WorldWideScience

Sample records for creep buckling behavior

  1. Creep buckling analysis of shells

    Energy Technology Data Exchange (ETDEWEB)

    Stone, C.M.; Nickell, R.E.

    1977-01-01

    The current study was conducted in an effort to determine the degree of conservatism or lack of conservatism in current ASME design rules concerning time-dependent (creep) buckling. In the course of this investigation, certain observations were made concerning the numerical solution of creep buckling problems. It was demonstrated that a nonlinear finite element code could be used to solve the time-dependent buckling problem. A direct method of solution was presented which proved to be computationally efficient and provided answers which agreed very well with available analytical solutions. It was observed that the calculated buckling times could vary widely for small errors in computed displacements. The presence of high creep strain rates contributed to the prediction of early buckling times when calculated during the primary creep stage. The predicted time estimates were found to increase with time until the secondary stage was reached and the estimates approached the critical times predicted without primary creep. It can be concluded, therefore, that for most nuclear piping components, whose primary creep stage is small compared to the secondary stage, the effect of primary creep is negligible and can be omitted from the calculations. In an evaluation of the past and current ASME design rules for time-dependent, load controlled buckling, it was concluded that current use of design load safety factors is not equivalent to a safety factor of ten on service life for low creep exponents.

  2. On the durable critic load in creep buckling of viscoelastic laminated plates and circular cylindrical shells

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Based on the first order shear deformation theory and classic buckling theory, the paper investigates the creep buckling behavior of viscoelastic laminated plates and laminated circular cylindrical shells. The analysis and elaboration of both instantaneous elastic critic load and durable critic load are emphasized. The buckling load in phase domain is obtained from governing equations by applying Laplace transform, and the instantaneous elastic critic load and durable critic load are determined according to the extreme value theorem for inverse Laplace transform. It is shown that viscoelastic approach and quasi-elastic approach yield identical solutions for these two types of critic load respectively. A transverse disturbance model is developed to give the same mechanics significance of durable critic load as that of elastic critic load. Two types of critic loads of boron/epoxy composite laminated plates and circular cylindrical shells are discussed in detail individually, and the influencing factors to induce creep buckling are revealed by examining the viscoelasticity incorporated in transverse shear deformation and in-plane flexibility.

  3. Creep behavior of microbiotic crust

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The creep behavior of microbiotic crust at room temperature was revealed by the creep bending tests of cantilever beam under constant-load conditions.The variation in the deflection with time can be depicted well by a standard creep curve.Creep rupture is a fundamental failure mechanism of microbiotic crust due to creep.A simple theory was then applied to describe this new me-chanical behavior.The existence of creep phenomenon brings into question the validity of widely used methods for measuring the strength of microbiotic crust.

  4. Stochastic behavior of nanoscale dielectric wall buckling

    Science.gov (United States)

    Friedman, Lawrence H.; Levin, Igor; Cook, Robert F.

    2016-01-01

    The random buckling patterns of nanoscale dielectric walls are analyzed using a nonlinear multi-scale stochastic method that combines experimental measurements with simulations. The dielectric walls, approximately 200 nm tall and 20 nm wide, consist of compliant, low dielectric constant (low-k) fins capped with stiff, compressively stressed TiN lines that provide the driving force for buckling. The deflections of the buckled lines exhibit sinusoidal pseudoperiodicity with amplitude fluctuation and phase decorrelation arising from stochastic variations in wall geometry, properties, and stress state at length scales shorter than the characteristic deflection wavelength of about 1000 nm. The buckling patterns are analyzed and modeled at two length scales: a longer scale (up to 5000 nm) that treats randomness as a longer-scale measurable quantity, and a shorter-scale (down to 20 nm) that treats buckling as a deterministic phenomenon. Statistical simulation is used to join the two length scales. Through this approach, the buckling model is validated and material properties and stress states are inferred. In particular, the stress state of TiN lines in three different systems is determined, along with the elastic moduli of low-k fins and the amplitudes of the small-scale random fluctuations in wall properties—all in the as-processed state. The important case of stochastic effects giving rise to buckling in a deterministically sub-critical buckling state is demonstrated. The nonlinear multiscale stochastic analysis provides guidance for design of low-k structures with acceptable buckling behavior and serves as a template for how randomness that is common to nanoscale phenomena might be measured and analyzed in other contexts. PMID:27330220

  5. Buckling Behavior of Substrate Supported Graphene Sheets

    Directory of Open Access Journals (Sweden)

    Kuijian Yang

    2016-01-01

    Full Text Available The buckling of graphene sheets on substrates can significantly degrade their performance in materials and devices. Therefore, a systematic investigation on the buckling behavior of monolayer graphene sheet/substrate systems is carried out in this paper by both molecular mechanics simulations and theoretical analysis. From 70 simulation cases of simple-supported graphene sheets with different sizes under uniaxial compression, two different buckling modes are investigated and revealed to be dominated by the graphene size. Especially, for graphene sheets with length larger than 3 nm and width larger than 1.1 nm, the buckling mode depends only on the length/width ratio. Besides, it is revealed that the existence of graphene substrate can increase the critical buckling stress and strain to 4.39 N/m and 1.58%, respectively, which are about 10 times those for free-standing graphene sheets. Moreover, for graphene sheets with common size (longer than 20 nm, both theoretical and simulation results show that the critical buckling stress and strain are dominated only by the adhesive interactions with substrate and independent of the graphene size. Results in this work provide valuable insight and guidelines for the design and application of graphene-derived materials and nano-electromechanical systems.

  6. Interaction Between Axisymmetric and Multilobed Creep Buckling of Circular Cylindrical Shells in Axial Compression.

    Science.gov (United States)

    general equilibrium equations derived for shallow shells are expressed in terms of the stresses and deviations corresponding to the equivalent sandwich model. The radial displacement as well as the meridional, circumferential and membrane shear stresses are expressed by finite Fourier series for each face of the sandwich model. A closed form solution is found for the multilobed deformation rates and for the critical time as well. A numerical integration of the deformation rates shows, for a given cylinder, that the multilobed creep buckling deformations grow much faster

  7. Buckling behavior of pipes in oil and gas wells

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Based on the non-linear differential equations of buckled pipes, the buckling behavior of pipes in different wellbores has been analyzed. The relation between the deflection of buckled pipe and the loads on it has been given, and the critical loads for sinusodal and helical buckling within different wellbores subjected to axial and torsional loads have been determined. Therefore, the profile of load increase during the post-buckling process and the bending moments in the buckled pipe can be determined. In addition, the effects of down-hole packer as fixed end on the helical buckling behavior of pipes have been investigated. These results can be applied to the related engineering design and construction.

  8. Creep rupture behavior of unidirectional advanced composites

    Science.gov (United States)

    Yeow, Y. T.

    1980-01-01

    A 'material modeling' methodology for predicting the creep rupture behavior of unidirectional advanced composites is proposed. In this approach the parameters (obtained from short-term tests) required to make the predictions are the three principal creep compliance master curves and their corresponding quasi-static strengths tested at room temperature (22 C). Using these parameters in conjunction with a failure criterion, creep rupture envelopes can be generated for any combination of in-plane loading conditions and ambient temperature. The analysis was validated experimentally for one composite system, the T300/934 graphite-epoxy system. This was done by performing short-term creep tests (to generate the principal creep compliance master curves with the time-temperature superposition principle) and relatively long-term creep rupture tensile tests of off-axis specimens at 180 C. Good to reasonable agreement between experimental and analytical results is observed.

  9. Dynamic buckling behavior of thin metal film lines from substrate

    Science.gov (United States)

    Wu, Dan; Xie, Huimin; Wang, Heling; Zhang, Jie; Li, Chuanwei

    2014-10-01

    The dynamic buckling behavior of thin films from substrate is studied in this work. The experimental results show that the buckling morphology of the constantan film lines from the polymer substrate is inconsistent and non-sinusoidal, which is different from the sinusoidal form of the buckling morphology under static loads. The plastic deformation of the film lines results in the non-sinusoidal buckling morphology and residual deformation when unloaded. Finite element modeling results with regard to the plastic dissipation of the constantan film lines reveal that the plastic dissipation suppresses the buckling-driven delaminating under impact loads. This study will give some new perspectives on the buckling behavior of thin film from substrate.

  10. Modeling creep behavior of fiber composites

    Science.gov (United States)

    Chen, J. L.; Sun, C. T.

    1988-01-01

    A micromechanical model for the creep behavior of fiber composites is developed based on a typical cell consisting of a fiber and the surrounding matrix. The fiber is assumed to be linearly elastic and the matrix nonlinearly viscous. The creep strain rate in the matrix is assumed to be a function of stress. The nominal stress-strain relations are derived in the form of differential equations which are solved numerically for off-axis specimens under uniaxial loading. A potential function and the associated effective stress and effective creep strain rates are introduced to simplify the orthotropic relations.

  11. Theory of buckling and post-buckling behavior of elastic structures

    Science.gov (United States)

    Budiansky, B.

    1974-01-01

    The present paper provides a unified, general presentation of the basic theory of the buckling and post-buckling behavior of elastic structures in a form suitable for application to a wide variety of special problems. The notation of functional analysis is used for this purpose. Before the general analysis, simple conceptual models are used to elucidate the basic concepts of bifurcation buckling, snap buckling, imperfection sensitivity, load-shortening relations, and stability. The energy approach, the virtual-work approach, and mode interaction are discussed. The derivations and results are applicable to continua and finite-dimensional systems. The virtual-work and energy approaches are given separate treatments, but their equivalence is made explicit. The basic concepts of stability occupy a secondary position in the present approach.

  12. Correlation of Creep Behavior of Domal Salts

    Energy Technology Data Exchange (ETDEWEB)

    Munson, D.E.

    1999-02-16

    assumptions permit the set to be completed. From the analysis, two distinct response groups were evident, with the salts of one group measurably more creep resistant than the other group. Interestingly, these groups correspond well with the indirectly determined creep closure of the SPR storage caverns, a correlation that probably should be expected. Certainly, the results suggest a simple laboratory determination of the creep characteristics of a salt material from a dome site can indicate the relative behavior of any potential cavern placed within that dome.

  13. Flexural-torsional buckling behavior of aluminum alloy beams

    Institute of Scientific and Technical Information of China (English)

    Xiaonong GUO; Zhe XIONG; Zuyan SHEN

    2015-01-01

    This paper presents an investigation on the flexural-torsional buckling behavior of aluminum alloy beams (AAB). First, based on the tests of 14 aluminum alloy beams under concentrated loads, the failure pattern, load- deformation curves, bearing capacity and flexural-torsional buckling factor are studied. It is found that all the beam specimens collapsed in the flexuml-torsional buckling with excessive deformation pattern. Moreover, the span, loading location and slenderness ratio influence the flexural-torsional buckling capacity of beams significantly. Secondly, besides the experiments, a finite element method (FEM) analysis on the flexural-torsional buckling behavior of AAB is also conducted. The main parameters in the FEM analysis are initial imperfection, material property, cross-section and loading scheme. According to the analytical results, it is indicated that the FEM is reasonable to capture mechanical behavior of AAB. Finally, on the basis of the experimental and analytical results, theoretical formulae to estimate the flexural- torsional buckling capacity of AAB are proposed, which could improve the application of present codes for AAB.

  14. Creep Aging Behavior Characterization of 2219 Aluminum Alloy

    Directory of Open Access Journals (Sweden)

    Lingfeng Liu

    2016-06-01

    Full Text Available In order to characterize the creep behaviors of 2219 aluminum alloy at different temperatures and stress levels, a RWS-50 Electronic Creep Testing Machine (Zhuhai SUST Electrical Equipment Company, Zhuhai, China was used for creep experiment at temperatures of 353~458 k and experimental stresses of 130~170 MPa. It was discovered that this alloy displayed classical creep curve characteristics in its creep behaviors within the experimental parameters, and its creep value increased with temperature and stress. Based on the creep equation of hyperbolic sine function, regression analysis was conducted of experimental data to calculate stress exponent, creep activation energy, and other related variables, and a 2219 aluminum alloy creep constitutive equation was established. Results of further analysis of the creep mechanism of the alloy at different temperatures indicated that the creep mechanism of 2219 aluminum alloy differed at different temperatures; and creek characteristics were presented in three stages at different temperatures, i.e., the grain boundary sliding creep mechanism at a low temperature stage (T < 373 K, the dislocation glide creep mechanism at a medium temperature stage (373 K ≤ T < 418 K, and the dislocation climb creep mechanism at a high temperature stage (T ≥ 418 K. By comparative analysis of the fitting results and experiment data, they were found to be in agreement with the experimental data, revealing that the established creep constitutive equation is suitable for different temperatures and stresses.

  15. Perturbation analysis on post-buckling behavior of pile

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The nonlinear large deflection differential equation, based on the assumption that the subsoil coefficient is the 2nd root of the depth, was established by energy method. The perturbation parameter was introduced to transform the equation to a series of linear differential equations to be solved, and the deflection function according with the boundary condition was considered. Then,the nonlinear higher-order asymptotic solution of post-buckling behavior of a pile was obtained by parameter-substituting. The influencing factors such as bury-depth ratio and stiffness ratio of soil to pile, slenderness ratio on the post-buckling behavior of a pile were analyzed. The results show that the pile is more unstable when the bury-depth ratio and stiffness ratio of soil to pile increase,and although the buckling load increases with the stiffness of soil, the pile may ruin for its brittleness. Thus, in the region where buckling behavior of pile must be taken into account, the high grade concrete is supposed to be applied, and the dynamic buckling behavior of pile needs to be further studied.

  16. Homogenized Creep Behavior of CFRP Laminates at High Temperature

    Science.gov (United States)

    Fukuta, Y.; Matsuda, T.; Kawai, M.

    In this study, creep behavior of a CFRP laminate subjected to a constant stress is analyzed based on the time-dependent homogenization theory developed by the present authors. The laminate is a unidirectional carbon fiber/epoxy laminate T800H/#3631 manufactured by Toray Industries, Inc. Two kinds of creep analyses are performed. First, 45° off-axis creep deformation of the laminate at high temperature (100°C) is analyzed with three kinds of creep stress levels, respectively. It is shown that the present theory accurately predicts macroscopic creep behavior of the unidirectional CFRP laminate observed in experiments. Then, high temperature creep deformations at a constant creep stress are simulated with seven kinds of off-axis angles, i.e., θ = 0°, 10°, 30°, 45°, 60°, 75°, 90°. It is shown that the laminate has marked in-plane anisotropy with respect to the creep behavior.

  17. Creep Behavior and Microstructure Evolution of P92 Steel During Creep Test at 873 K

    Science.gov (United States)

    Zhang, Zuogui; Shi, Kexian; Wang, Yanfeng; Lin, Fusheng

    In this paper, the creep behavior of P92 steel has been analyzed by creep strain and creep rate variations after the creep tests were stopped at the steady-state creep stage. The microstructure evolution of the P92 steel at the steady-state stage during creep test at 873 K under different load stresses of 125-160 MPa were studied by using a scanning electron microscopy (SEM) and a transmission electron microscopy (TEM). The grain boundary characteristics in the P92 steels during creep test were investigated by an electron backscattered diffraction (EBSD) technique. Experimental results showed that with increasing load stresses from 125 MPa to 160 MPa, creep rates of the P92 steels increased in Norton's power law relation and creep times to the steady-state creep stage decreased. With decreasing load stresses and increasing creep times, martensite lath microstructure occurred recovery and the dislocation densities in ferritic matrix decreased. M23C6 particles located in prior austenite grain, sub-grain and lath boundaries showed slight coarsening. Some Laves phase particles precipitated in the grain boundaries for the P92 specimens after creep test under a load stress of 125 MPa. Comparing to as-tempered P92 steel, the volume fractions of LAGBs are lower and the volume fraction of HAGBs are higher with decreasing load stresses and increasing creep times. It is considered that understanding on creep behavior and microstructual evolution of the P92 steels during creep test will effectively support life design and assessment of the high temperature metal parts in fossil-fired power plant.

  18. The dynamic aspects of thermo-elasto-viscoplastic snap-through and creep buckling phenomena

    Science.gov (United States)

    Riff, R.; Simitses, G. J.

    1987-01-01

    Use of a mathematical model and solution methodology, to examine dynamic buckling and dynamic postbuckling behavior of shallow arches and spherical caps made of a realistic material and undergoing non-isothermal, elasto-viscoplastic deformation was examined. Thus, geometric as well as material type nonlinearities of higher order are included in this analysis. The dynamic stability problem is studied under impulsive loading and suddenly applied loading with loads of constant magnitude and infinite duration. A finite element model was derived directly from the incrementally formulated nonlinear shell equations, by using a tensor-oriented procedure. As an example of the results, the time history of the midspan displacement of a damped shallow circular arch is presented.

  19. On the buckling behavior of piezoelectric nanobeams: An exact solution

    Energy Technology Data Exchange (ETDEWEB)

    Jandaghian, Ali Akbar; Rahmaini, Omid [University of Zanjan, Zanjan (Iran, Islamic Republic of)

    2015-08-15

    In this paper, thermoelectric-mechanical buckling behavior of the piezoelectric nanobeams is investigated based on the nonlocal theory and Euler-Bernoulli beam theory. The electric potential is assumed linear through the thickness of the nanobeam and the governing equations are derived by Hamilton's principle. The governing equations are solved analytically for different boundary conditions. The effects of the nonlocal parameter, temperature change, and external electric voltage on the critical buckling load of the piezoelectric nanobeams are discussed in detail. This study should be useful for the design of piezoelectric nanodevices.

  20. Creep rupture behavior of welded Grade 91 steel

    Energy Technology Data Exchange (ETDEWEB)

    Shrestha, Triratna [Department of Chemical and Materials Engineering, University of Idaho, Moscow, ID 83844 (United States); Basirat, Mehdi [Department of Mechanical Engineering, University of Idaho, Moscow, ID 83844 (United States); Alsagabi, Sultan; Sittiho, Anumat [Department of Chemical and Materials Engineering, University of Idaho, Moscow, ID 83844 (United States); Charit, Indrajit, E-mail: icharit@uidaho.edu [Department of Chemical and Materials Engineering, University of Idaho, Moscow, ID 83844 (United States); Potirniche, Gabriel P. [Department of Mechanical Engineering, University of Idaho, Moscow, ID 83844 (United States)

    2016-07-04

    Creep rupture behavior of fusion welded Grade 91 steel was studied in the temperature range of 600 – 700 °C and at stresses of 50–200 MPa. The creep data were analyzed in terms of the Monkman-Grant relation and Larson-Miller parameter. The creep damage tolerance factor was used to identify the origin of creep damage. The creep damage was identified as the void growth in combination with microstructural degradation. The fracture surface morphology of the ruptured specimens was studied by scanning electron microscopy and deformed microstructure examined by transmission electron microscopy, to further elucidate the rupture mechanisms.

  1. Uniaxial tension and tensile creep behaviors of EPS

    Institute of Scientific and Technical Information of China (English)

    康颖安; 李显方; 谭加才

    2008-01-01

    The mechanical behavior of EPS(Expanded polystyrene) with three densities at room temperature and under tension loading was studied.The results show that EPS material is characterized by brittle behavior in the tension tests,and tensile properties of EPS increase with the increase of density.Volume fraction has no a significant effect on the modulus of these foams.The tensile creep strain increases with stress for EPS with same density,indicating that the creep behavior is of the stress dependency.And the creep behavior of EPS exhibits density dependency,which the creep strain decreases with densities for a fixed stress value.Moreover the creep behavior under the constant tension load is well in coincidence with the three-parameter solid model.

  2. Locally Corroded Stiffener Effect on Shear Buckling Behaviors of Web Panel in the Plate Girder

    Directory of Open Access Journals (Sweden)

    Jungwon Huh

    2015-01-01

    Full Text Available The shear buckling failure and strength of a web panel stiffened by stiffeners with corrosion damage were examined according to the degree of corrosion of the stiffeners, using the finite element analysis method. For this purpose, a plate girder with a four-panel web girder stiffened by vertical and longitudinal stiffeners was selected, and its deformable behaviors and the principal stress distribution of the web panel at the shear buckling strength of the web were compared after their post-shear buckling behaviors, as well as their out-of-plane displacement, to evaluate the effect of the stiffener in the web panel on the shear buckling failure. Their critical shear buckling load and shear buckling strength were also examined. The FE analyses showed that their typical shear buckling failures were affected by the structural relationship between the web panel and each stiffener in the plate girder, to resist shear buckling of the web panel. Their critical shear buckling loads decreased from 82% to 59%, and their shear buckling strength decreased from 88% to 76%, due to the effect of corrosion of the stiffeners on their shear buckling behavior. Thus, especially in cases with over 40% corrosion damage of the vertical stiffener, they can have lower shear buckling strength than their design level.

  3. Creep Behavior of Passive Bovine Extraocular Muscle

    OpenAIRE

    Lawrence Yoo; Hansang Kim; Andrew Shin; Vijay Gupta; Demer, Joseph L.

    2011-01-01

    This paper characterized bovine extraocular muscles (EOMs) using creep, which represents long-term stretching induced by a constant force. After preliminary optimization of testing conditions, 20 fresh EOM samples were subjected to four different loading rates of 1.67, 3.33, 8.33, and 16.67%/s, after which creep was observed for 1,500 s. A published quasilinear viscoelastic (QLV) relaxation function was transformed to a creep function that was compared with data. Repeatable creep was observed...

  4. Effect of Topological Defects on Buckling Behavior of Single-walled Carbon Nanotube

    Directory of Open Access Journals (Sweden)

    Wang Guoxiu

    2011-01-01

    Full Text Available Abstract Molecular dynamic simulation method has been employed to consider the critical buckling force, pressure, and strain of pristine and defected single-walled carbon nanotube (SWCNT under axial compression. Effects of length, radius, chirality, Stone–Wales (SW defect, and single vacancy (SV defect on buckling behavior of SWCNTs have been studied. Obtained results indicate that axial stability of SWCNT reduces significantly due to topological defects. Critical buckling strain is more susceptible to defects than critical buckling force. Both SW and SV defects decrease the buckling mode of SWCNT. Comparative approach of this study leads to more reliable design of nanostructures.

  5. Creep behavior of passive bovine extraocular muscle.

    Science.gov (United States)

    Yoo, Lawrence; Kim, Hansang; Shin, Andrew; Gupta, Vijay; Demer, Joseph L

    2011-01-01

    This paper characterized bovine extraocular muscles (EOMs) using creep, which represents long-term stretching induced by a constant force. After preliminary optimization of testing conditions, 20 fresh EOM samples were subjected to four different loading rates of 1.67, 3.33, 8.33, and 16.67%/s, after which creep was observed for 1,500 s. A published quasilinear viscoelastic (QLV) relaxation function was transformed to a creep function that was compared with data. Repeatable creep was observed for each loading rate and was similar among all six anatomical EOMs. The mean creep coefficient after 1,500 seconds for a wide range of initial loading rates was at 1.37 ± 0.03 (standard deviation, SD). The creep function derived from the relaxation-based QLV model agreed with observed creep to within 2.7% following 16.67%/s ramp loading. Measured creep agrees closely with a derived QLV model of EOM relaxation, validating a previous QLV model for characterization of EOM biomechanics.

  6. Creep Behavior of Passive Bovine Extraocular Muscle

    Directory of Open Access Journals (Sweden)

    Lawrence Yoo

    2011-01-01

    Full Text Available This paper characterized bovine extraocular muscles (EOMs using creep, which represents long-term stretching induced by a constant force. After preliminary optimization of testing conditions, 20 fresh EOM samples were subjected to four different loading rates of 1.67, 3.33, 8.33, and 16.67%/s, after which creep was observed for 1,500 s. A published quasilinear viscoelastic (QLV relaxation function was transformed to a creep function that was compared with data. Repeatable creep was observed for each loading rate and was similar among all six anatomical EOMs. The mean creep coefficient after 1,500 seconds for a wide range of initial loading rates was at 1.37±0.03 (standard deviation, SD. The creep function derived from the relaxation-based QLV model agreed with observed creep to within 2.7% following 16.67%/s ramp loading. Measured creep agrees closely with a derived QLV model of EOM relaxation, validating a previous QLV model for characterization of EOM biomechanics.

  7. Creep behavior of Zr-Nb alloys

    Energy Technology Data Exchange (ETDEWEB)

    Suh, Yong Chan; Kim, Young Suk; Cheong, Yong Mu; Kwon, Sang Chul; Kim, Sung Soo; Choo, Ki Nam [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-01-01

    The creep characteristics of Zirconium alloy is affected by several parameters. Out-reactor creep increases both with an increasing amount of Nb, Sn and S contained in alpha-Zr and decreases with the increasing volume of alpha-Zr. Especially, the creep of Zr-2.5Nb alloy depends on the solubility of Nb in alpha-Zr, which is associated with the decomposition of beta-Zr. Since Zr of the hcp structure is strongly anisotropic, it shows the characteristics of texture and results in the anisotropy of creep. Due to the circumferential texture of Zr-2.5%Nb alloy (CANDU Pressure tube), the longitudinal slip is easier than the circumferential one, resulting in the high creep rate. The irradiation creep also increases with increasing neutron fluence. The neutron irradiation increases the strength of the zirconium alloys but decreases their creep strength. In contrast to the out-reactor creep, the irradiation creep is little sensitive to temperature, resulting in the lower activation energy. The most important factor to affect the in-reactor and out-reactor creep of niobium containing alloys seems to be the solution hardening by Nb or Sn which is soluble in alpha-zirconium and the texture as well. Irradiation growth is the mechanism which is caused only by the irradiation. It becomes saturated at lower fluence than the critical fluence but beyond it, shows the break-away growth. The onset of accelerated irradiation growth corresponds with the c-dislocation loop formation, though its mechanism needs better understanding. Generally, the irradiation growth of Zr-Nb alloys increases with an increase in fluence, cold working, dislocation, density and temperature, and with a decrease in the grain size. 141 refs., 59 figs., 10 tabs. (Author)

  8. Creep behavior of abaca fibre reinforced composite material

    Energy Technology Data Exchange (ETDEWEB)

    Tobias, B.C.; Lieng, V.T. [Victoria Univ. of Technology, Victoria (Australia)

    1996-12-31

    This study investigates the creep behavior of abaca fibre reinforced composite lamina. The optimum proportions of constituents and loading conditions, temperature and stresses, are investigated in terms of creep properties. Lamina with abaca fibre volume fractions of 60, 70 and 80 percent, embedded in polyester resin were fabricated. Creep tests in tension at three temperature levels 20{degrees}C, 100{degrees}C and 120{degrees}C and three constant stress levels of 0. 1 MPa, 0. 13 Mpa and 0. 198 MPa using a Dynamic Mechanical Analyzer (DMA) were performed. The creep curves show standard regions of an ideal creep curve such as primary and secondary creep stage. The results also show that the minimum creep rate of abaca fibre reinforced composite increases with the increase of temperature and applied stress. Plotting the minimum creep rate against stress, depicts the variations of stress exponents which vary from 1.6194 at 20{degrees}C to 0.4576 at 120{degrees}C.

  9. A Comparison of the Irradiation Creep Behavior of Several Graphites

    Energy Technology Data Exchange (ETDEWEB)

    Burchell, Timothy D [ORNL; Windes, Will [Idaho National Laboratory (INL)

    2016-01-01

    Graphite creep strain data from the irradiation creep capsule Advanced Graphite Creep-1 (AGC-1) are reported. This capsule was the first (prototype) of a series of five or six capsules planned as part of the AGC experiment, which was designed to fully characterize the effects of neutron irradiation and the radiation creep behavior of current nuclear graphite. The creep strain data and analysis are reported for the six graphite grades incorporated in the capsule. The AGC-1 capsule was irradiated in the Advanced Test Reactor at Idaho National Laboratory (INL) at approximately 700 C and to a peak dose of 7 dpa (displacements per atom). The specimen s final dose, temperature, and stress conditions have been reported by INL and were used during this analysis. The derived creep coefficients (K) were calculated for each grade and were found to compare well to literature data for the creep coefficient, even under the wide range of AGC-1 specimen temperatures. Comparisons were made between AGC-1 data and historical grade data for creep coefficients.

  10. Molecular dynamics simulation on the buckling behavior of GaN nanowires under uniaxial compression

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Zhiguo; Zu, Xiaotao; Yang, Li; Gao, Fei; Weber, William J

    2008-01-01

    Molecular dynamics simulation is one of the most promising methods for investigating the mechanical behavior of nanostructures, such as nanowires and nanotubes. Atomistic simulations are performed to investigate the buckling properties of [001], [11¯0] and [110] oriented GaN nanowires under uniaxial compression, these three types of nanowires correspond to experimentally synthesized nanowires. The effects of simulation temperature, and wire length on the buckling behavior are investigated. The simulation results show that critical stress decreases with the increase of wire length, which is in agreement with the Euler theory. Buckling occurs as a result of dynamic processes, buckling strain (and corresponding stress) decreases as temperature is increased.

  11. Understanding the nanoscale local buckling behavior of vertically aligned MWCNT arrays with van der Waals interactions

    Science.gov (United States)

    Li, Yupeng; Kim, Hyung-Ick; Wei, Bingqing; Kang, Junmo; Choi, Jae-Boong; Nam, Jae-Do; Suhr, Jonghwan

    2015-08-01

    The local buckling behavior of vertically aligned carbon nanotubes (VACNTs) has been investigated and interpreted in the view of a collective nanotube response by taking van der Waals interactions into account. To the best of our knowledge, this is the first report on the case of collective VACNT behavior regarding van der Waals force among nanotubes as a lateral support effect during the buckling process. The local buckling propagation and development of VACNTs were experimentally observed and theoretically analyzed by employing finite element modeling with lateral support from van der Waals interactions among nanotubes. Both experimental and theoretical analyses show that VACNTs buckled in the bottom region with many short waves and almost identical wavelengths, indicating a high mode buckling. Furthermore, the propagation and development mechanism of buckling waves follow the wave damping effect.The local buckling behavior of vertically aligned carbon nanotubes (VACNTs) has been investigated and interpreted in the view of a collective nanotube response by taking van der Waals interactions into account. To the best of our knowledge, this is the first report on the case of collective VACNT behavior regarding van der Waals force among nanotubes as a lateral support effect during the buckling process. The local buckling propagation and development of VACNTs were experimentally observed and theoretically analyzed by employing finite element modeling with lateral support from van der Waals interactions among nanotubes. Both experimental and theoretical analyses show that VACNTs buckled in the bottom region with many short waves and almost identical wavelengths, indicating a high mode buckling. Furthermore, the propagation and development mechanism of buckling waves follow the wave damping effect. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr03581c

  12. Creep Behavior and Mechanism for CMCs with Continuous Ceramic Fibers

    Science.gov (United States)

    Chermant, Jean-Louis; Farizy, Gaëlle; Boitier, Guillaume; Darzens, Séverine; Vicens, Jean; Sangleboeuf, Jean-Christophe

    This paper gives an overview on the creep behavior and mechanism of some CMCs, with a SiC ceramic matrix, such as Cf-SiC, SiCf-SiC and SiCf-SiBC. Tensile creep tests were conducted under argon and air in order to have the influence of the environmental conditions on the macroscopical mechanical response. Nevertheless, multi-scale and multi-technique approaches were required to identify and quantify mechanism(s) which is (are) involved in the creep behavior. The initiation and propagation of damages which are occurring under high stress and temperature conditions were investigated at mesoscopic, microscopic and nanoscopic scales using SEM, TEM and HREM, in order to identify the mechanism(s) involved at each scale. Automatic image analysis was used in order to quantify the evolution of some damage morphological parameters. The macroscopical creep behavior has been investigated through a damage mechanics approach which seems to be the most promising route. A good correlation was found between the kinetics of the damage mechanisms and the creep behavior. For such ceramic matrix composites, the governing mechanism is a damage-creep one, with an additional delay effect due to formation of a glass when tests are performed under air.

  13. Bending and buckling behavior analysis of foamed metal circular plate.

    Science.gov (United States)

    Fan, Jian Ling; Ma, Lian Sheng; Zhang, Lu; De Su, Hou

    2016-07-04

    This paper establishes a density gradient model along the thickness direction of a circular plate made of foamed material. Based on the first shear deformation plate theory, the result is deduced that the foamed metal circular plate with graded density along thickness direction yields axisymmetric bending problem under the action of uniformly distributed load, and the analytical solution is obtained by solving the governing equation directly. The analyses on two constraint conditions of edge radial clamping and simply supported show that the density gradient index and external load may affect the axisymmetric bending behavior of the plate. Then, based on the classical plate theory, the paper analyzes the behavior of axisymmetric buckling under radial pressure applied on the circular plate. Shooting method is used to obtain the critical load, and the effects of gradient nature of material properties and boundary conditions on the critical load of the plate are analyzed.

  14. Effect of misalignment on mechanical behavior of metals in creep. [computer programs

    Science.gov (United States)

    Wu, H. C.

    1979-01-01

    Application of the endochronic theory of viscoplasticity to creep, creep recovery, and stress relaxation at the small strain and short time range produced the following results: (1) The governing constitutive equations for constant-strain-rate stress-strain behavior, creep, creep recovery, and stress relaxation were derived by imposing appropriate constraints on the general constitutive equation of the endochronic theory. (2) A set of material constants was found which correlate strain-hardening, creep, creep recovery, and stress relaxation. (3) The theory predicts with reasonable accuracy the creep and creep recovery behaviors at short time. (4) The initial strain history prior to the creep stage affects the subsequent creep significantly. (5) A critical stress was established for creep recovery. A computer program, written for the misalignment problem is reported.

  15. Creep Behavior of Poly(lactic acid) Based Biocomposites

    Science.gov (United States)

    Morreale, Marco; Mistretta, Maria Chiara; Fiore, Vincenzo

    2017-01-01

    Polymer composites containing natural fibers are receiving growing attention as possible alternatives for composites containing synthetic fibers. The use of biodegradable matrices obtained from renewable sources in replacement for synthetic ones is also increasing. However, only limited information is available about the creep behavior of the obtained composites. In this work, the tensile creep behavior of PLA based composites, containing flax and jute twill weave woven fabrics, produced through compression molding, was investigated. Tensile creep tests were performed at different temperatures (i.e., 40 and 60 °C). The results showed that the creep behavior of the composites is strongly influenced by the temperature and the woven fabrics used. As preliminary characterization, quasi-static tensile tests and dynamic mechanical tests were carried out on the composites. Furthermore, fabrics (both flax and jute) were tested as received by means of quasi-static tests and creep tests to evaluate the influence of fabrics mechanical behavior on the mechanical response of the resulting composites. The morphological analysis of the fracture surface of the tensile samples showed the better fiber-matrix adhesion between PLA and jute fabric. PMID:28772755

  16. Creep Behavior of Poly(lactic acid Based Biocomposites

    Directory of Open Access Journals (Sweden)

    Marco Morreale

    2017-04-01

    Full Text Available Polymer composites containing natural fibers are receiving growing attention as possible alternatives for composites containing synthetic fibers. The use of biodegradable matrices obtained from renewable sources in replacement for synthetic ones is also increasing. However, only limited information is available about the creep behavior of the obtained composites. In this work, the tensile creep behavior of PLA based composites, containing flax and jute twill weave woven fabrics, produced through compression molding, was investigated. Tensile creep tests were performed at different temperatures (i.e., 40 and 60 °C. The results showed that the creep behavior of the composites is strongly influenced by the temperature and the woven fabrics used. As preliminary characterization, quasi-static tensile tests and dynamic mechanical tests were carried out on the composites. Furthermore, fabrics (both flax and jute were tested as received by means of quasi-static tests and creep tests to evaluate the influence of fabrics mechanical behavior on the mechanical response of the resulting composites. The morphological analysis of the fracture surface of the tensile samples showed the better fiber-matrix adhesion between PLA and jute fabric.

  17. Creep and Creep Crack Growth Behaviors for SMAW Weldments of Gr. 91 Steel

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Woo Gon; Yin, Song Nan; Park, Ji Yeon; Hong, Sung Deok; Kim, Yong Wan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Jae Young [Pukyong National University, Busan (Korea, Republic of)

    2010-05-15

    High Cr ferritic resistance steels with tempered martensite microstructures posses enhanced creep strength at the elevated temperatures. Those steels as represented by a modified 9Cr-1Mo steel (ASME Grade 91, hereafter Gr.91) are regarded as main structural materials of sodium-cooled fast reactors (SFR) and reactor pressure vessel materials of very high temperature reactors (VHTR). The SFR and VHTR systems are designed during long-term duration reaching 60 years at elevated temperatures and often subjected to non-uniform stress and temperature distribution during service. These conditions may generate localized creep damage and propagate the cracks and ultimately may cause a fracture. A significant portion of its life is spent in crack propagation. Therefore, a creep crack growth rate (CCGR) due to creep damage should be assessed for both the base metal (BM) and welded metal (WM). Enough CCGR data for them should be provided for assessing their structural integrities. However, their CCGR data for the Gr. 91 steels is still insufficient. In this study, the CCGR for the BM and the WM of the Gr. 91 steel was comparatively investigated. A series of the CCG tests were conducted under different applied loads for the BM and the WM at 600 .deg. C. The CCGR was characterized in terms of the C parameter, and their CCG behavior were compared, respectively

  18. Creep and recovery behavior analysis of space mesh structures

    Science.gov (United States)

    Tang, Yaqiong; Li, Tuanjie; Ma, Xiaofei

    2016-11-01

    The Schapery's nonlinear viscoelastic theory and nonlinear force-density method have been investigated to analyze the creep and recovery behaviors of space deployable mesh reflectors in this paper. Based on Schapery's nonlinear viscoelastic theory, we establish the creep and recovery constitutive model for cables whose pretensions were applied stepwise in time. This constitutive model has been further used for adjustment of cables' elongation rigidity. In addition, the time-dependent tangent stiffness matrix is calculated by the partial differentiation of the corresponding load vector with respect to the nodal coordinate vector obtained by the nonlinear force-density method. An incremental-iterative solution based on the Newton-Raphson method is adopted for solving the time-dependent nonlinear statics equations. Finally, a hoop truss reflector antenna is presented as a numerical example to illustrate the efficiency of the proposed method for the creep and recovery behavior analysis of space deployable mesh structures.

  19. Creep and creep-rupture behavior of a continuous strand, swirl mat reinforced polymer composite in automotive environments

    Energy Technology Data Exchange (ETDEWEB)

    Ren, W.; Brinkman, C.R. [Oak Ridge National Lab., TN (United States). Metals and Ceramics Div.

    1998-12-31

    Creep and creep-rupture behavior of an isocyanurate based polyurethane matrix with a continuous strand, swirl mat E-glass reinforcement was investigated for automotive applications. The material under stress was exposed to various automobile service environments. Results show that environment has substantial effects on its creep and creep-rupture properties. Proposed design guide lines and stress reduction factors were developed for various automotive environments. These composites are considered candidate structural materials for light weight and fuel efficient automobiles of the future.

  20. Mechanical behavior of carbon nanotubes in the rippled and buckled phase

    Science.gov (United States)

    Jackman, H.; Krakhmalev, P.; Svensson, K.

    2015-02-01

    We have studied the mechanical behavior of multi-walled carbon nanotubes for bending strains beyond the onset for rippling and buckling. We found a characteristic drop in the bending stiffness at the rippling and buckling onset and the relative retained stiffness was dependent on the nanotube dimensions and crystallinity. Thin tubes are more prone to buckle, where some lose all of their bending stiffness, while thicker tubes are more prone to ripple and on average retain about 20% of their bending stiffness. In defect rich tubes, the bending stiffness is very low prior to rippling, but these tubes retain up to 70% of their initial bending stiffness.

  1. Shear stress relaxation of dental ceramics determined from creep behavior.

    Science.gov (United States)

    DeHoff, Paul H; Anusavice, Kenneth J

    2004-10-01

    To test the hypothesis that shear stress relaxation functions of dental ceramics can be determined from creep functions measured in a beam-bending viscometer. Stress relaxation behavior was determined from creep data for the following materials: (1) a veneering ceramic-IPS Empress2 body ceramic (E2V); (2) an experimental veneering ceramic (EXV); (3) a low expansion body porcelain-Vita VMK 68 feldspathic body porcelain (VB); (4) a high expansion body porcelain-Will Ceram feldspathic body porcelain (WCB); (5) a medium expansion opaque porcelain-Vita feldspathic opaque porcelain (VO); and (6) a high expansion opaque porcelain-Will Ceram feldspathic opaque porcelain (WCO). Laplace transform techniques were used to relate shear stress relaxation functions to creep functions for an eight-parameter, discrete viscoelastic model. Nonlinear regression analysis was performed to fit a four-term exponential relaxation function for each material at each temperature. The relaxation functions were utilized in the ANSYS finite element program to simulate creep behavior in three-point bending for each material at each temperature. Shear stress relaxation times at 575 degrees C ranged from 0.03 s for EXV to 195 s for WCO. Knowledge of the shear relaxation functions for dental ceramics at high temperatures is required input for the viscoelastic element in the ANSYS finite element program, which can used to determine transient and residual stresses in dental prostheses during fabrication.

  2. Assessment of Tungsten Content on Tertiary Creep Deformation Behavior of Reduced Activation Ferritic-Martensitic Steel

    Science.gov (United States)

    Vanaja, J.; Laha, Kinkar

    2015-10-01

    Tertiary creep deformation behavior of reduced activation ferritic-martensitic (RAFM) steels having different tungsten contents has been assessed. Creep tests were carried out at 823 K (550 °C) over a stress range of 180 to 260 MPa on three heats of the RAFM steel (9Cr-W-0.06Ta-0.22V) with tungsten content of 1, 1.4, and 2.0 wt pct. With creep exposure, the steels exhibited minimum in creep rate followed by progressive increase in creep rate until fracture. The minimum creep rate decreased, rupture life increased, and the onset of tertiary stage of creep deformation delayed with the increase in tungsten content. The tertiary creep behavior has been assessed based on the relationship, , considering minimum creep rate () instead of steady-state creep rate. The increase in tungsten content was found to decrease the rate of acceleration of tertiary parameter ` p.' The relationships between (1) tertiary parameter `p' with minimum creep rate and time spent in tertiary creep deformation and (2) the final creep rate with minimum creep rate revealed that the same first-order reaction rate theory prevailed in the minimum creep rate as well as throughout the tertiary creep deformation behavior of the steel. A master tertiary creep curve of the steels has been developed. Scanning electron microscopic investigation revealed enhanced coarsening resistance of carbides in the steel on creep exposure with increase in tungsten content. The decrease in tertiary parameter ` p' with tungsten content with the consequent decrease in minimum creep rate and increase in rupture life has been attributed to the enhanced microstructural stability of the steel.

  3. Mechanical Behavior of Low Porosity Carbonate Rock: From Brittle Creep to Ductile Creep.

    Science.gov (United States)

    Nicolas, A.; Fortin, J.; Gueguen, Y.

    2014-12-01

    Mechanical compaction and associated porosity reduction play an important role in the diagenesis of porous rocks. They may also affect reservoir rocks during hydrocarbon production, as the pore pressure field is modified. This inelastic compaction can lead to subsidence, cause casing failure, trigger earthquake, or change the fluid transport properties. In addition, inelastic deformation can be time - dependent. In particular, brittle creep phenomena have been deeply investigated since the 90s, especially in sandstones. However knowledge of carbonates behavior is still insufficient. In this study, we focus on the mechanical behavior of a 14.7% porosity white Tavel (France) carbonate rock (>98% calcite). The samples were deformed in a triaxial cell at effective confining pressures ranging from 0 MPa to 85 MPa at room temperature and 70°C. Experiments were carried under dry and water saturated conditions in order to explore the role played by the pore fluids. Two types of experiments have been carried out: (1) a first series in order to investigate the rupture envelopes, and (2) a second series with creep experiments. During the experiments, elastic wave velocities (P and S) were measured to infer crack density evolution. Permeability was also measured during creep experiments. Our results show two different mechanical behaviors: (1) brittle behavior is observed at low confining pressures, whereas (2) ductile behavior is observed at higher confining pressures. During creep experiments, these two behaviors have a different signature in term of elastic wave velocities and permeability changes, due to two different mechanisms: development of micro-cracks at low confining pressures and competition between cracks and microplasticity at high confining pressure. The attached figure is a summary of 20 triaxial experiments performed on Tavel limestone under different conditions. Stress states C',C* and C*' and brittle strength are shown in the P-Q space: (a) 20°C and dry

  4. Experimental Investigation on Creep Deformation Behavior of Medium-strength Marble Rock

    Directory of Open Access Journals (Sweden)

    Li Yong

    2014-01-01

    Full Text Available The creep deformation behavior of rocks has significant effect on the stability of underground structures. This study presents the short-term and creep deformation behavior of medium-strength marble rock using a conventional uniaxial compression testing machine and a servo-controlled rheology testing machine. The uniaxial compressive strength is obtained by the uniaxial compression testing machine. During the creep behavior test, two types of rock specimens (dry and water-saturated are specified to be used to perform the uniaxial creep tests. Two rheological failure modes and the relationship curves between axial/circumferential strain and stress levels of marble specimens are also obtained from the creep test results. Eventually, the creep deformation behaviors are compared with those of typical soft rocks. These creep curves combined with a given creep constitutive model would provide accurate parameters for long-term stability analyses of actual projects.

  5. Development of Finite Element Model for the Static Buckling Behavior of the Spacer Grid

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, Young Ik; Park, Nam Gyu; Kim, Kyoung Ju; Suh, Jung Min [Kepco Nuclear Fuel, Daejeon (Korea, Republic of)

    2013-10-15

    In this study, finite element model was proposed to evaluate the buckling characteristics and structural behavior of partial spacer grids. A two-dimensional model was developed to simplify a real spacer gird model and save analysis time. And it was validated for comparison with experimental tests. A non-linear analysis method was introduced to perform realistic simulation. Later, the buckling analysis of the full size grid will be performed based on the analysis results of partial spacer grids. A study was conducted to develop the simplified model of a spacer grid and provide a prediction of buckling behavior. The FE analysis results are quite similar to the experimental tests. · The deformed geometry of FE model after compression is consistent and very similar to that of real situation, and the non-linear analysis method used in this model can simulate buckling and post-buckling behavior well. · The buckling strength obtained by FEM shows a very good agreement with the physical tests.

  6. Microstructural Evaluation and Thermal Creep Behavior of Zr-Excel

    Science.gov (United States)

    Ahmmed, Kazi Foyez

    Dual phase (alpha-beta) Zr-Excel Pressure Tube (PT) material has been heat treated in the (alpha+beta) or beta-phase regime to generate variable microstructures. These heat-treated microstructures revealed significant modification in the inital microstructure. The microstructural changes by heat-treatment will have a profound influence on their deformation behavior; characterizing those properties is the main goal of this study. In this dissertation, the experimental results are presented in a manuscript format, which is divided in three technical chapters. Chapter 3 discusses the effect of heat treatment on texture modification; where, as received (ASR) PT materials were heated to a range of temperatures and cooled either in water or in air. It has been observed that due to the orientation relationship between alpha and beta-phase, the ASR microstructure has been significantly altered during heating and cooling. The extent of this alteration strongly depends on the solution temperature and cooling rate. Although, variant selection is observed during texture modification, significant randomization is noticed in the room temperature texture. In Chapter 4, line profile analysis technique has been used to quantitatively analyze the microstructural details of the heat-treated materials. Diffraction pattern analyses demonstrated significant peak broadening in the heat-treated material; which is attributed due to the increase of volume fraction of martensitic alpha and alteration in the dislocation structures. Line profile analyses also revealed that primary alpha consists with large sub-grains and correlated dislocations but the martensitic alpha are highly dislocated. Finally in Chapter 5, thermal creep behavior of the heat treated materials has been studied. Microstructural analyses were also conducted in the pre- and post-creep materials to understand the creep mechanism. Creep anisotropy of the heat treated materials has been investigated by correlating the

  7. Brittle Creep Failure, Critical Behavior, and Time-to-Failure Prediction of Concrete under Uniaxial Compression

    Directory of Open Access Journals (Sweden)

    Yingchong Wang

    2015-01-01

    Full Text Available Understanding the time-dependent brittle deformation behavior of concrete as a main building material is fundamental for the lifetime prediction and engineering design. Herein, we present the experimental measures of brittle creep failure, critical behavior, and the dependence of time-to-failure, on the secondary creep rate of concrete under sustained uniaxial compression. A complete evolution process of creep failure is achieved. Three typical creep stages are observed, including the primary (decelerating, secondary (steady state creep regime, and tertiary creep (accelerating creep stages. The time-to-failure shows sample-specificity although all samples exhibit a similar creep process. All specimens exhibit a critical power-law behavior with an exponent of −0.51 ± 0.06, approximately equal to the theoretical value of −1/2. All samples have a long-term secondary stage characterized by a constant strain rate that dominates the lifetime of a sample. The average creep rate expressed by the total creep strain over the lifetime (tf-t0 for each specimen shows a power-law dependence on the secondary creep rate with an exponent of −1. This could provide a clue to the prediction of the time-to-failure of concrete, based on the monitoring of the creep behavior at the steady stage.

  8. Functional buckling behavior of silicone rubber shells for biomedical use

    NARCIS (Netherlands)

    van der Houwen, E B; Kuiper, L H; Burgerhof, J G M; van der Laan, B F A M; Verkerke, G J

    2013-01-01

    BACKGROUND: The use of soft elastic biomaterials in medical devices enables substantial function integration. The consequent increased simplification in design can improve reliability at a lower cost in comparison to traditional (hard) biomaterials. Functional bi-stable buckling is one of the many n

  9. Viscoelastoplastic constitutive model for creep deformation behavior of asphalt sand

    Institute of Scientific and Technical Information of China (English)

    叶永; 杨新华; 陈传尧

    2008-01-01

    A uniaxial viscoelastoplastic model that can describe whole creep behaviors of asphalt sand at different temperatures was presented.The model was composed of three submodels in series,which describe elastoplastic,viscoelastic and viscoplastic characteristics respectively.The constitutive equation was established for uniaxial loading condition,and the creep representation was also obtained.The constitutive parameters were determined by uniaxial compression tests under controlled-stress of 0.1 MPa with five different test temperatures of 20,40,45,50 and 60 ℃.Expressions of the model parameters in terms of temperatures were also given.The model gave prediction at various temperatures consistent with the experimental results,and can reflect the total deformation characterization of asphalt sands.

  10. The creep behavior of acrylic denture base resins.

    Science.gov (United States)

    Sadiku, E R; Biotidara, F O

    1996-01-01

    The creep behavior of acrylic dental base resins, at room temperature and at different loading conditions, has been examined. The behaviors of these resins are similar to that of "commercial perspex" at room temperature over a period of 1000 seconds. The pseudo-elastic moduli of the blends of PMMA VC show a significant increase compared with PMMA alone. The addition of the PVC powder to the heat-cured acrylic resin increased the time-dependent elastic modulus. This increase in elastic modulus is advantageous in the production of denture based resins of improv mechanical properties.

  11. Time-Dependent Behavior of Diabase and a Nonlinear Creep Model

    Science.gov (United States)

    Yang, Wendong; Zhang, Qiangyong; Li, Shucai; Wang, Shugang

    2014-07-01

    Triaxial creep tests were performed on diabase specimens from the dam foundation of the Dagangshan hydropower station, and the typical characteristics of creep curves were analyzed. Based on the test results under different stress levels, a new nonlinear visco-elasto-plastic creep model with creep threshold and long-term strength was proposed by connecting an instantaneous elastic Hooke body, a visco-elasto-plastic Schiffman body, and a nonlinear visco-plastic body in series mode. By introducing the nonlinear visco-plastic component, this creep model can describe the typical creep behavior, which includes the primary creep stage, the secondary creep stage, and the tertiary creep stage. Three-dimensional creep equations under constant stress conditions were deduced. The yield approach index (YAI) was used as the criterion for the piecewise creep function to resolve the difficulty in determining the creep threshold value and the long-term strength. The expression of the visco-plastic component was derived in detail and the three-dimensional central difference form was given. An example was used to verify the credibility of the model. The creep parameters were identified, and the calculated curves were in good agreement with the experimental curves, indicating that the model is capable of replicating the physical processes.

  12. Experimental Investigation on Creep Deformation Behavior of Medium-strength Marble Rock

    OpenAIRE

    Li Yong; Zhu Weishen; Li Shucai

    2014-01-01

    The creep deformation behavior of rocks has significant effect on the stability of underground structures. This study presents the short-term and creep deformation behavior of medium-strength marble rock using a conventional uniaxial compression testing machine and a servo-controlled rheology testing machine. The uniaxial compressive strength is obtained by the uniaxial compression testing machine. During the creep behavior test, two types of rock specimens (dry and water-saturated) are speci...

  13. Magnetic field effects on buckling behavior of smart size-dependent graded nanoscale beams

    Science.gov (United States)

    Ebrahimi, Farzad; Reza Barati, Mohammad

    2016-07-01

    In this article, buckling behavior of nonlocal magneto-electro-elastic functionally graded (MEE-FG) beams is investigated based on a higher-order beam model. Material properties of smart nanobeam are supposed to change continuously throughout the thickness based on the power-law model. Eringen's nonlocal elasticity theory is adopted to capture the small size effects. Nonlocal governing equations of MEE-FG nanobeam are obtained employing Hamilton's principle and they are solved using the Navier solution. Numerical results are presented to indicate the effects of magnetic potential, electric voltage, nonlocal parameter and material composition on buckling behavior of MEE-FG nanobeams. Therefore, the present study makes the first attempt in analyzing the buckling responses of higher-order shear deformable (HOSD) MEE-FG nanobeams.

  14. Creep of Refractory Fibers and Modeling of Metal and Ceramic Matrix Composite Creep Behavior

    Science.gov (United States)

    Tewari, S.N.

    1995-01-01

    Our concentration during this research was on the following subprograms. (1) Ultra high vacuum creep tests on 218, ST300 and WHfC tungsten and MoHfC molybdenum alloy wires, temperature range from 1100 K to 1500 K, creep time of 1 to 500 hours. (2) High temperature vacuum tensile tests on 218, ST300 and WHfC tungsten and MoHfC molybdenum alloy wires. (3) Air and vacuum tensile creep tests on polycrystalline and single crystal alumina fibers, such as alumina-mullite Nextel fiber, yttrium aluminum ganet (YAG) and Saphikon, temperature range from 1150 K to 1470 K, creep time of 2 to 200 hours. (4) Microstructural evaluation of crept fibers, TEM study on the crept metal wires, SEM study on the fracture surface of ceramic fibers. (5) Metal Matrix Composite creep models, based on the fiber creep properties and fiber-matrix interface zone formation.

  15. Buckling Behavior of Long Anisotropic Plates Subjected to Fully Restrained Thermal Expansion

    Science.gov (United States)

    Nemeth, Michael P.

    2003-01-01

    An approach for synthesizing buckling results and behavior for thin, balanced and unbalanced symmetric laminates that are subjected to uniform heating or cooling and which are fully-restrained against thermal expansion or contraction is presented. This approach uses a nondimensional analysis for infinitely long, flexurally anisotropic plates that are subjected to combined mechanical loads and is based on useful nondimensional parameters. In addition, stiffness-weighted laminate thermal-expansion parameters are derived and used to determine critical temperature changes in terms of physically intuitive mechanical buckling coefficients. The effects of membrane orthotropy and anisotropy are included. Many results are presented for some common laminates that are intended to facilitate a structural designer's transition to the use of the generic buckling design curves that are presented in the paper. Several generic buckling design curves are presented that provide physical insight into buckling response and provide useful design data. Examples are presented that demonstrate the use of generic design curves. The analysis approach and generic results indicate the effects and characteristics of laminate thermal expansion, membrane orthotropy and anisotropy, and flexural orthotropy and anisotropy in a very general, unifying manner.

  16. Comparison of Accelerated Compressive Creep Behavior of Virgin HDPE Using Thermal and Energy Approaches

    Science.gov (United States)

    Bozorg-Haddad, Amir; Iskander, Magued

    2011-10-01

    This article compares two available approaches for accelerating the creep response of viscoelastic materials, such as High Density Polyethylene (HDPE), which is increasingly gaining attention for use in construction. Thermal acceleration methods to predict the tensile creep of polymers are already available. The Time-Temperature Superposition (TTS) phenomenon is the basis of several available methods, and an ASTM standard for tensile creep of geosynthetics is based on one of its derivatives, the Stepped Isothermal Method (SIM). In this article, both TTS and SIM have been adapted to study the compressive creep of virgin HDPE. An alternate approach, based on the equivalence of strain energy density (SED) between conventional constant-stress creep tests and strain-controlled stress-strain tests, is also adapted for accelerated compressive creep of HDPE. There is remarkably a good agreement among the creep behaviors obtained from conventional tests, TTS, SIM, and SED predictions for virgin HDPE.

  17. On the analysis and evaluation of enhanced creep behavior of LMFBR structure

    Energy Technology Data Exchange (ETDEWEB)

    Kim, J. B.; Lee, H. Y.; Lee, J. M.; Lee, J. H

    2003-03-01

    High temperature structures of LMR experience inelastic deformation such as plasticity and creep due to high temperature operating temperature of 530{approx}550 .deg. C. The generated creep strains are connected with the stress relaxations, redistributions and/or progressive deformations. The superposition of primary and secondary stresses may lead to enhanced creep deformations. The term 'creep ratchetting' refer to the phenomenon where enhanced creep occurs with plasticity ratcheting. The interchange of elastoplastic and creep strains is important for its understanding. Since creep ratcheting is highly nonlinear structural behavior, it is required to secure the proper analysis technique to evaluate inelastic strain due to enhanced creep. In this project, the simplified evaluation method for enhanced creep using core stress concept was investigated and the enhanced creep of pipe subjected to sustained axial tensile loading and transient thermal loading with hold time was evaluated using several analysis models; that is, isotropic hardening model, kinematic hardening model and combined hardening model with Norton's power law creep equation. In addition, the viscoplastic analysis using NONSTA-VP was performed for comparisons. The simplified evaluation method using core stress concept yields conservative result as expected. It is necessary to systematize the simplified evaluation procedure, to analyze the conservatism of the method, and to improve the inelastic analysis techniques including NONSTA-VP.

  18. Buckling Behavior of Cold-Formed Studs with Thermal Perforations

    Directory of Open Access Journals (Sweden)

    Garifullin Marsel

    2016-01-01

    Full Text Available Studies have shown that the optimal structural scheme for low-rise buildings that meets all regulatory requirements is a frame system. In this connection, thin-walled cold-formed steel (CFS profiles seem to be the best material for constructing light steel framed (LSF walls. The framework of LSF walls is usually constructed from CFS C-shaped profiles. To increase the thermal effectiveness of a wall, CFS profiles usually have thermal perforations and thus are called thermoprofiles. However, these openings have a negative impact on bearing capacity of profiles and require accurate evaluation. In this article a relatively new reticular-stretched thermoprofile with diamond-shaped openings is considered. The article deals with the buckling analysis of perforated CFS C-sections subjected to compression.

  19. Renewal theory applied to creep and inelastic behavior of copper

    Energy Technology Data Exchange (ETDEWEB)

    Gibbons, K.A.; Cook, D.E. [Wright-Patterson Air Force Base, Dayton, OH (United States); Bearden, K.L. [Air Force Academy, Colorado Springs, CO (United States)

    1995-12-31

    A series of constant load creep tests on C11000 copper are described. The copper microstructure was closely controlled through appropriate heat treatment. Renewal theory was applied to interpret creep test data while developing the parameters of a general inelasticity model suitable for prediction. Creep experiments were predicted using renewal theory. Time varying load and load control stress-strain experiments were also predicted using renewal inelasticity theory. Results show that renewal theory is an efficient and effective approach to modeling creep of copper, needing a limited number of parameters. The simplicity of applying this theory to creep, variable load conditions, and a stress-strain experiment predictions for copper has been demonstrated.

  20. Creep and creep-fatigue behavior of high chromium steel weldment

    Institute of Scientific and Technical Information of China (English)

    Yukio TAKAHASHI; Masaaki TABUCHI

    2011-01-01

    Manuscript received I December 2010; in revised form 9 March 2011Strength of welded joints of high chromium steels is one of the important concerns for fabricators and operators of ultra supercritical thermal power plants. A number of creep as well as creep-fatigue tests with tensile hold have been carried out on the welded joints of two types of high chromium steels widely used in Japan, I.e. Grade 91 and 122 steels. It was found that failure occurred in fine grain heat-affected zone in all the creep-fatigue tests, even at a relatively low temperature and fairly short time where failure occurred in plain base metal region in simple creep testing. Four procedures were used to predict failure lives and their results were compared with the test results. A newly proposed energy-based approach gave the best estimation of failure life, without respect of the material and temperature.

  1. Modeling of Different Fiber Type and Content SiC/SiC Minicomposites Creep Behavior

    Science.gov (United States)

    Almansour, Amjad S.; Morscher, Gregory N.

    2017-01-01

    Silicon Carbide based Ceramic Matrix Composites (CMCs) are attractive materials for use in high-temperature applications in the aerospace and nuclear industries. However, creep damage mechanism in CMCs is the most dominant mechanism at elevated temperatures. Consequently, the tensile creep behavior of Hi-Nicalon, Hi-Nicalon Type S SiC fibers and Chemical vapor infiltrated Silicon Carbide matrix (CVI-SiC) were characterized and creep parameters were extracted from creep experiments. Some fiber creep tests were performed in inert environment at 1200 C on individual fibers. Creep behavior of different fiber content pristine and precracked Hi-Nicalon and Hi-Nicalon Type S reinforced minicomposites with BN interphases and CVI-SiC matrix were then modelled using the creep data found in this study and the literature and compared with creep experiments results for the pristine and precracked Hi-Nicalon and Hi-Nicalon Type S minicomposites. Finally, the effects of load-sharing and matrix cracking on CMC creep behavior will be discussed.

  2. A Simplified Analysis of the Post-buckling Behavior of a Compressed Reinforcing Bar

    Directory of Open Access Journals (Sweden)

    P. Kabele

    2004-01-01

    Full Text Available Recently, a computational methodology based on a sequential multiscale approach, which facilitates numerical simulation of an R/C building demolition has been developed. In this type of analysis, it is necessary to capture the behavior of compressed reinforcement bars until complete rupture, which occurs due to extensive bending in the post-buckling regime. To this end, a simplified analytical model of the post-buckling behavior of a compressed bar is proposed. The simplification consists namely in considering rigid-plastic material behavior, neglecting axial contraction of the central line, and approximating the shape of the deformed central line in the plastic hinges by a circular arch. Consequently, the axial loading force, bar end displacement, and extreme strain can be expressed in relatively simple closed forms. The results obtained with the proposed model show very close agreement with those obtained by a detailed and realistic finite element analysis, which justifies the use of the simplifying assumptions. 

  3. Buckling Behavior of Long Anisotropic Plates Subjected to Elastically Restrained Thermal Expansion

    Science.gov (United States)

    Nemeth, Michael P.

    2002-01-01

    An approach for synthesizing buckling results for, and behavior of, thin balanced and unbalanced symmetric laminates that are subjected to uniform heating or cooling and elastically restrained against thermal expansion or contraction is presented. This approach uses a nondimensional analysis for infinitely long, flexurally anisotropic plates that are subjected to combined mechanical loads and is based on useful nondimensional parameters. In addition, stiffness-weighted laminate thermal-expansion parameters and compliance coefficients are derived that are used to determine critical temperatures in terms of physically intuitive mechanical-buckling coefficients. The effects of membrane orthotropy and membrane anisotropy are included in the general formulation. Many results are presented for some common laminates that are intended to facilitate a structural designer's transition to the use of generic buckling design curves. Several curves that illustrate the fundamental parameters used in the analysis are presented, for nine contemporary material systems, that provide physical insight into the buckling response in addition to providing useful design data. Examples are presented that demonstrate the use of generic design curves. The analysis approach and generic results indicate the effects and characteristics of elastically restrained laminate thermal expansion or contraction, membrane orthotropy and anisotropy, and flexural orthotropy and anisotropy in a very general and unifying manner.

  4. Influence of Uncertainties on the Dynamic Buckling Loads of Structures Liable to Asymmetric Postbuckling Behavior

    Directory of Open Access Journals (Sweden)

    Paulo B. Gonçalves

    2008-01-01

    Full Text Available Structural systems liable to asymmetric bifurcation usually become unstable at static load levels lower than the linear buckling load of the perfect structure. This is mainly due to the imperfections present in real structures. The imperfection sensitivity of structures under static loading is well studied in literature, but little is know on the sensitivity of these structures under dynamic loads. The aim of the present work is to study the behavior of an archetypal model of a harmonically forced structure, which exhibits, under increasing static load, asymmetric bifurcation. First, the integrity of the system under static load is investigated in terms of the evolution of the safe basin of attraction. Then, the stability boundaries of the harmonically excited structure are obtained, considering different loading processes. The bifurcations connected with these boundaries are identified and their influence on the evolution of safe basins is investigated. Then, a parametric analysis is conducted to investigate the influence of uncertainties in system parameters and random perturbations of the forcing on the dynamic buckling load. Finally, a safe lower bound for the buckling load, obtained by the application of the Melnikov criterion, is proposed which compare well with the scatter of buckling loads obtained numerically.

  5. Mechanisms Governing the Creep Behavior of High Temperature Alloys for Generation IV Nuclear Energy Systems

    Energy Technology Data Exchange (ETDEWEB)

    Vasudevan, Vijay [Univ. of Cincinnati, OH (United States); Carroll, Laura [Idaho National Lab. (INL), Idaho Falls, ID (United States); Sham, Sam [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-04-06

    This research project, which includes collaborators from INL and ORNL, focuses on the study of alloy 617 and alloy 800H that are candidates for applications as intermediate heat exchangers in GEN IV nuclear reactors, with an emphasis on the effects of grain size, grain boundaries and second phases on the creep properties; the mechanisms of dislocation creep, diffusional creep and cavitation; the onset of tertiary creep; and theoretical modeling for long-term predictions of materials behavior and for high temperature alloy design.

  6. Effects of stress and physical ageing on nonlinear creep behavior of poly(methyl methacrylate)

    Institute of Scientific and Technical Information of China (English)

    赵荣国; 陈朝中; 李其抚; 罗文波

    2008-01-01

    The effects of stress,ageing time and ageing temperature on creep behavior of poly(methyl methacrylate) were studied.After annealing above its glass transition temperature for a period of time to eliminate the stress and thermal history,the specimens were quenched and aged at various ageing temperatures for different ageing time,and then the short-term creep tests under different stress levels were carried out at room temperature.The creep strains were modeled by means of time-ageing time equivalence and time-stress equivalence,and the master creep curves were constructed via ageing time shift factors and stress shift factors.The results indicate that the creep rate increases with stress,while decreases with ageing time,and the ageing temperature history obviously affects the creep rate.For linear viscoelastic material,the ageing shift rate is independent on imposed stress,while for nonlinear viscoelastic material,the ageing shift rate decreases with increasing stress.The unified master creep curve up to 540 d at reference state was constructed by shifting the creep curves horizontally along the logarithmic time axis to overlap each other.It is demonstrated that the time-stress equivalence,united with the time-ageing time equivalence,provides an effective accelerated characterization technique in the laboratory to evaluate the long-term creep behavior of physical ageing polymers.

  7. Influence of Prior Fatigue Cycling on Creep Behavior of Reduced Activation Ferritic-Martensitic Steel

    Science.gov (United States)

    Sarkar, Aritra; Vijayanand, V. D.; Parameswaran, P.; Shankar, Vani; Sandhya, R.; Laha, K.; Mathew, M. D.; Jayakumar, T.; Rajendra Kumar, E.

    2014-06-01

    Creep tests were carried out at 823 K (550 °C) and 210 MPa on Reduced Activation Ferritic-Martensitic (RAFM) steel which was subjected to different extents of prior fatigue exposure at 823 K at a strain amplitude of ±0.6 pct to assess the effect of prior fatigue exposure on creep behavior. Extensive cyclic softening that characterized the fatigue damage was found to be immensely deleterious for creep strength of the tempered martensitic steel. Creep rupture life was reduced to 60 pct of that of the virgin steel when the steel was exposed to as low as 1 pct of fatigue life. However, creep life saturated after fatigue exposure of 40 pct. Increase in minimum creep rate and decrease in creep rupture ductility with a saturating trend were observed with prior fatigue exposures. To substantiate these findings, detailed transmission electron microscopy studies were carried out on the steel. With fatigue exposures, extensive recovery of martensitic-lath structure was distinctly observed which supported the cyclic softening behavior that was introduced due to prior fatigue. Consequently, prior fatigue exposures were considered responsible for decrease in creep ductility and associated reduction in the creep rupture strength.

  8. The vibrational and buckling behaviors of piezoelectric nanobeams with surface effects

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Z; Jiang, L Y, E-mail: lyjiang@eng.uwo.ca [Department of Mechanical and Materials Engineering, University of Western Ontario, London, ON, N6A 5B9 (Canada)

    2011-06-17

    In this work, the influence of surface effects, including residual surface stress, surface elasticity and surface piezoelectricity, on the vibrational and buckling behaviors of piezoelectric nanobeams is investigated by using the Euler-Bernoulli beam theory. The surface effects are incorporated by applying the surface piezoelectricity model and the generalized Young-Laplace equations. The results demonstrate that surface effects play a significant role in predicting these behaviors. It is found that the influence of the residual surface stress and the surface piezoelectricity on the resonant frequencies and the critical electric potential for buckling is more prominent than the surface elasticity. The nanobeam boundary conditions are also found to influence the surface effects on these parameters. This study also shows that the resonant frequencies can be tuned by adjusting the applied electrical load. The present study is envisaged to provide useful insights for the design and applications of piezoelectric-beam-based nanodevices.

  9. Experimental investigation of creep behavior of clastic rock in Xiangjiaba Hydropower Project

    Directory of Open Access Journals (Sweden)

    Yu ZHANG

    2015-01-01

    Full Text Available There are many fracture zones crossing the dam foundation of the Xiangjiaba Hydropower Project in southwestern China. Clastic rock is the main media of the fracture zone and has poor physical and mechanical properties. In order to investigate the creep behavior of clastic rock, triaxial creep tests were conducted using a rock servo-controlling rheological testing machine. The results show that the creep behavior of clastic rock is significant at a high level of deviatoric stress, and less time-dependent deformation occurs at high confining pressure. Based on the creep test results, the relationship between axial strain and time under different confining pressures was investigated, and the relationship between axial strain rate and deviatoric stress was also discussed. The strain rate increases rapidly, and the rock sample fails eventually under high deviatoric stress. Moreover, the creep failure mechanism under different confining pressures was analyzed. The main failure mechanism of clastic rock is plastic shear, accompanied by a significant compression and ductile dilatancy. On the other hand, with the determined parameters, the Burgers creep model was used to fit the creep curves. The results indicate that the Burgers model can exactly describe the creep behavior of clastic rock in the Xiangjiaba Hydropower Project.

  10. Effect of Zr on behavior of compressive creep in as cast ZA27 alloy

    Institute of Scientific and Technical Information of China (English)

    魏晓伟; 沈保罗

    2003-01-01

    The effect of Zr on the behavior of compressive creep in as cast ZA27 alloy was investigated in the temperature range of 20-160 ℃ and under different compressive stresses in the range of 50-137.5 MPa with special apparatus. The results show that the primary compressive creep strains and steady creep rates of ZA27-Zr alloy and ZA27 alloy increase with increasing temperature and stress. However, the primary compressive creep strain and steady creep rate of the ZA27-Zr alloy are lower than that of the ZA27 alloy below 100 ℃, but higher at 160 ℃. The compressive creep behaviors in both ZA27-Zr alloy and ZA27 alloy obey an empirical equation lnt=C-nlnσ+Q/RT, and the exponent stress n is 3.63 for ZA27-Zr alloy and 3.46 for ZA27 alloy, respectively, the activation energy Q is 87.32 kJ/mol for ZA27-Zr alloy and 81.09 kJ/mol for ZA27 alloy. Different material structural constants are associated with different compressive creep behaviors in the alloy. The compressive creep rate in the alloy is controlled by the lattice diffusion of zinc and dislocation limb.

  11. Out-of-pile creep behavior of uranium carbide

    Science.gov (United States)

    Wright, T. R.; Seltzer, M. S.

    1974-01-01

    Compression creep tests were investigated on various UC-based fuel materials having a variation in both density and composition. Specimens were prepared by casting and by hot pressing. Steady-state creep rates were measured under vacuum at 1400 to 1800 C in the stress range 500-4000 psi.

  12. Initial approach to assess lateral buckling behavior: comparison between design and operational condition of offshore pipeline

    Energy Technology Data Exchange (ETDEWEB)

    Familiar Solano, Rafael; Reis Antunes, Bruno; Santos Hansen, Alexandre [PETROBRAS, Rio de Janeiro, (Brazil)

    2010-07-01

    Offshore pipelines can be subject to lateral buckling; some strategies are applied to prevent buckle initiation by monitoring the buckling behaviour. Some pipelines have been modified by PETROBRAS with triggers and sleepers; and distributed buoyancies have been added along the pipeline route. This paper investigated the thermo-mechanical design of the pipeline to avoid buckling and its consequences. Both planned buckles at dual sleepers and at distributed buoyancy modules and unplanned buckles were studied. Comparisons between the results obtained in design with finite element analysis and observed during operation with sidescan images were made. Seven planned buckles and two unplanned buckles were mapped and analyzed. It was found that the maximum stress, strain and fatigue damage at the buckle locations were fairly low. The mapping tests showed that the lengths and amplitudes of the buckles were compatible with lateral buckles in the design of pipelines.

  13. Fabrication and buckling behavior of polycrystalline palladium, cobalt, and rhodium nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Jahed, Zeinab [Department of Chemical Engineering, University of Waterloo, 200 University Avenue West, Waterloo, ON N2L 3G1 (Canada); Department of Mechanical and Mechatronics Engineering, University of Waterloo, 200 University Avenue West, Waterloo, ON N2L 3G1 (Canada); Jin, Sumin [Department of Chemical Engineering, University of Waterloo, 200 University Avenue West, Waterloo, ON N2L 3G1 (Canada); Waterloo Institute for Nanotechnology, University of Waterloo, 200 University Avenue West, Waterloo, ON N2L 3G1 (Canada); Burek, Michael J. [Waterloo Institute for Nanotechnology, University of Waterloo, 200 University Avenue West, Waterloo, ON N2L 3G1 (Canada); Tsui, Ting Y., E-mail: tttsui@uwaterloo.ca [Department of Chemical Engineering, University of Waterloo, 200 University Avenue West, Waterloo, ON N2L 3G1 (Canada); Department of Mechanical and Mechatronics Engineering, University of Waterloo, 200 University Avenue West, Waterloo, ON N2L 3G1 (Canada); Waterloo Institute for Nanotechnology, University of Waterloo, 200 University Avenue West, Waterloo, ON N2L 3G1 (Canada)

    2012-04-30

    Highlights: Black-Right-Pointing-Pointer Pd, Co, and Rh nano-pillars with diameter of {approx}130 nm were fabricated by using novel electron beam lithography and electroplating techniques. Black-Right-Pointing-Pointer Uniaxial compression load and displacement responses of the nanopillars were characterized. Black-Right-Pointing-Pointer Pd nano-pillars have the highest fracture toughness followed by Co and Rh pillars. Black-Right-Pointing-Pointer Tangent moduli of the three materials were extracted from the experimental results. - Abstract: Novel fabrication techniques were developed to manufacture polycrystalline palladium, cobalt, and rhodium nanopillars with diameters of approximately 130 nm. These nanostructures have length-to-radius ratios in the range of 4 and 20. Using uniaxial nano-compression techniques, the buckling behaviors of the produced nanopillars were characterized and critical buckling loads were extracted. The tangent moduli, which were extracted from plots of critical buckling load as a function of effective specimen cross-sectional area, of palladium, cobalt, and rhodium nanopillars are 90 {+-} 6 GPa, 175 {+-} 9 GPa, and 375 {+-} 23 GPa, respectively. As expected, these calculated values are slightly smaller than the bulk polycrystalline elastic moduli for all three materials. Post compression scanning electron microscope images revealed ductile behavior for palladium nanostructures, while cobalt and rhodium specimens failed by fracture.

  14. Optical measurement on dynamic buckling behavior of stiffened composite panels under in-plane shear

    Science.gov (United States)

    Lei, Zhenkun; Bai, Ruixiang; Tao, Wang; Wei, Xiao; Leng, Ruijiao

    2016-12-01

    The buckling behavior and failure mode of a composite panel stiffened by I-shaped stringers under in-plane shear is studied using digital fringe projection profilometry. The basic principles of the dynamic phase-shifting technique, multi-frequency phase-unwrapping technique and inverse-phase technique for nonlinear error compensation are introduced. Multi-frequency fringe projection profilometry was used to monitor and measure the change in the morphology of a discontinuous surface of the stiffened composite panel during in-plane shearing. Meanwhile, the strain history of multiple points on the skin was obtained using strain rosettes. The buckling mode and deflection of the panel at different moments were analyzed and compared with those obtained using the finite element method. The experimental results validated the FEM analysis.

  15. Controlled buckling behavior of patterned oxide structures on compliant substrates for flexible optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Bejitual, T.S.; Morris, N.J.; Cairns, D.R.; Sierros, K.A., E-mail: kostas.sierros@mail.wvu.edu

    2013-12-31

    There is currently a great interest to design and fabricate novel flexible devices for solar cell, solid-state lighting, biomedical and energy harvesting applications. Such devices require the use of electrode components. Desired electrodes must exhibit structural integrity, low electrical resistivity and, in most cases, high optical transparency in the visible range. Despite growing efforts to replace them, transparent conducting oxide layers deposited on polymer substrates are still enjoying a dominant role as the electrode component. This is because of their excellent combination of electrical and optical properties. However, their performance when they are subjected to externally-applied mechanical stresses is limited. Such performance has been extensively investigated for the case of continuous brittle oxide films on polymer substrates. However, there is relatively little work reported to date on the mechanical behavior of patterned conducting layers on compliant substrates. In this study we report on the mechanical behavior of various patterned indium tin oxide shapes and sizes on polyethylene terephthalate. Micron-sized shapes include squares, circles, and zigzag-based structures. Controlled buckling experiments are performed in-situ using an optical microscope in order to monitor critical strains and potential failure mechanisms. In addition, ITO electrical resistance changes are continuously monitored during deformation. Furthermore, ex-situ characterization of the tested surfaces using scanning electron microscopy is conducted. Higher crack onset values are observed for the smaller size patterns. Also, square-shaped patterns are found to exhibit the lowest crack onset values. SEM observations suggest cracking-driven and buckling-driven delamination during ITO tensile and compressive buckling mode respectively. In both cases, failure is observed to initiate from the pattern edges. - Highlights: • In-situ experimental analysis of various patterned shapes

  16. Creep Behavior of Solid Solution Strengthened Y3Al5O12

    Science.gov (United States)

    2007-11-02

    DATES COVERED Final Technical Report 15 Feb 97 to 29 Aug 97 4. TITLE AND SUBTITLE Creep Behavior of Solid Solution Strengthened Y3A15012 6...Final Report Title: Creep Behavior of Solid Solution Strengthened Y3AI5012 Award Number: F49620-97-1-0097 For the period of: 2/14/97-8/31/97...been investigated at present in these oxides is through the formation of solid solution alloys. For the case of oxides two different possible solid

  17. Creep behavior of bone cement: a method for time extrapolation using time-temperature equivalence.

    Science.gov (United States)

    Morgan, R L; Farrar, D F; Rose, J; Forster, H; Morgan, I

    2003-04-01

    The clinical lifetime of poly(methyl methacrylate) (PMMA) bone cement is considerably longer than the time over which it is convenient to perform creep testing. Consequently, it is desirable to be able to predict the long term creep behavior of bone cement from the results of short term testing. A simple method is described for prediction of long term creep using the principle of time-temperature equivalence in polymers. The use of the method is illustrated using a commercial acrylic bone cement. A creep strain of approximately 0.6% is predicted after 400 days under a constant flexural stress of 2 MPa. The temperature range and stress levels over which it is appropriate to perform testing are described. Finally, the effects of physical aging on the accuracy of the method are discussed and creep data from aged cement are reported.

  18. Time-dependent Creep Crack Growth Behavior of Alloy 617 at 800 .deg. C

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Woogon; Kim, Minhwan; Kim, Yongwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Jaeyoung; Ekaputra, I. M. W. [Pukyong National Univ., Busan (Korea, Republic of)

    2014-05-15

    The VHTR components are designed to be used for a 60 year lifetime at a high temperature, the creep crack growth (CCG) behavior as well as creep behavior is very important for the design application due to creep damage during the long service life at elevated temperatures. Alloy 617 is a major candidate material for the IHX component. The design of the component, which will operate well into the creep range, will require a good understanding of creep crack growth deformation. Efforts are now being undertaken in the Generation IV program to provide data needed for the design and licensing of the nuclear plants, and with this goal in mind, to meet the needs of the conceptual designers of the VHTR system, 'Gen-IV Materials Handbook DB' is being established through an international collaboration program of several GIF (Gen-IV Forum) countries. CCG experimental data should be prepared to 'the Gen-IV Materials Handbook DB' website, because the CCG data for Alloy 617 are not available in the ASME design code. In this paper, experimental creep crack growth data were obtained through a series of CCG tests performed under different applied loads at 800 .deg. C. The CCG behavior was characterized in terms of the C{sup *} fracture mechanics parameter, and the CCGR equation for Alloy 617 was presented. Experimental CCG data of Alloy 617 were obtained from a series of creep crack growth tests under different applied loads at 800 .deg. C.

  19. STATISTIC MODELING OF THE CREEP BEHAVIOR OF METAL MATRIX COMPOSITES BASED ON FINITE ELEMENT ANALYSIS

    Institute of Scientific and Technical Information of China (English)

    岳珠峰

    2002-01-01

    The aim of the paper is to discover the general creep mechanisms for the short fiber reinforcement matrix composites (MMCs) under uniaxial stress states and to build a relationship between the macroscopic steady creep behavior and the material micro geometric parameters. The unit cell models were used to calculate the macroscopic creep behavior with different micro geometric parameters of fibers on different loading directions. The influence of the geometric parameters of the fibers and loading directions on the macroscopic creep behavior had been obtained, and described quantitatively. The matrix/fiber interface had been considered by a third layer, matrix/fiber interlayer, in the unit cells with different creep properties and thickness. Based on the numerical results of the unit cell models, a statistic model had been presented for the plane randomly-distributed-fiber MMCs. The fiber breakage had been taken into account in the statistic model for it starts experimentally early in the creep life. With the distribution of the geometric parameters of the fibers, the results of the statistic model agree well with the experiments. With the statistic model, the influence of the geometric parameters and the breakage of the fibers as well as the properties and thickness of the interlayer on the macroscopic steady creep rate have been discussed.

  20. Comparative investigation of creep behavior of ceramic fiber-reinforced alumina and silica aerogel

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Xiaoguang; Wei, Jing [School of Energy and Power Engineering, Beihang University, P.O. Box 405, Beijing 100191 (China); Shi, Duoqi, E-mail: shdq@buaa.edu.cn [School of Energy and Power Engineering, Beihang University, P.O. Box 405, Beijing 100191 (China); Sun, Yantao; Lv, Shuangqi [School of Energy and Power Engineering, Beihang University, P.O. Box 405, Beijing 100191 (China); Feng, Jian; Jiang, Yonggang [National Key Laboratory of Science and Technology on Advanced Ceramic Fibers and Composites, College of Aerospace Science and Engineering, National University of Defense Technology, Changsha 410073 (China)

    2014-07-15

    Ambient and high temperature creep experiments at constant stresses of 0.05 MPa and 0.2 MPa were conducted on a ceramic fiber-reinforced alumina aerogel. Experimental results show that at low temperature (below 300 °C), there is no significant creep phenomenon at low stress level (0.05 MPa), but time-dependent creep deformation is found at high stress level (0.2 MPa) for the material. Scanning Electron Microscope (SEM) analysis was also conducted to understand the micro mechanism of the creep behavior. Crack initiation and propagation in matrix are the key factors that change the creep property. Comparative investigation of creep properties was also carried out between ceramic fiber-reinforced alumina and silica aerogel. Finally the application prospect of the two composites was discussed. The result shows that alumina aerogel has excellent creep resistance, thermal stability and heat insulation properties at high temperature (above 800 °C), and it has a good application prospect in high temperature insulation fields, while the ceramic fiber-reinforced silica aerogel, limited by the sintering and poor creep resistance under high temperature, is more suitable for low temperature (below 600 °C) insulation field.

  1. On the nonlinear axisymmetric dynamic buckling behavior of clamped functionally graded spherical caps

    Science.gov (United States)

    Prakash, T.; Sundararajan, N.; Ganapathi, M.

    2007-01-01

    Here, the dynamic thermal buckling behavior of functionally graded spherical caps is studied considering geometric nonlinearity based on von Karman's assumptions. The formulation is based on first-order shear deformation theory and it includes the in-plane and rotary inertia effects. The material properties are graded in the thickness direction according to the power-law distribution in terms of volume fractions of the material constituents. The effective material properties are evaluated using homogenization method. The governing equations obtained using finite element approach are solved employing the Newmark's integration technique coupled with a modified Newton-Raphson iteration scheme. The pressure load corresponding to a sudden jump in the maximum average displacement in the time history of the shell structure is taken as the dynamic buckling load. The present model is validated against the available isotropic case. A detailed numerical study is carried out to highlight the influences of shell geometries, power law index of functional graded material and boundary conditions on the dynamic buckling load of shallow spherical shells.

  2. Creep behavior for advanced polycrystalline SiC fibers

    Energy Technology Data Exchange (ETDEWEB)

    Youngblood, G.E.; Jones, R.H. [Pacific Northwest National Lab., Richland, WA (United States); Kohyama, Akira [Kyoto Univ. (Japan)] [and others

    1997-08-01

    A bend stress relaxation (BSR) test is planned to examine irradiation enhanced creep in polycrystalline SiC fibers which are under development for use as fiber reinforcement in SiC/SiC composite. Baseline 1 hr and 100 hr BSR thermal creep {open_quotes}m{close_quotes} curves have been obtained for five selected advanced SiC fiber types and for standard Nicalon CG fiber. The transition temperature, that temperature where the S-shaped m-curve has a value 0.5, is a measure of fiber creep resistance. In order of decreasing thermal creep resistance, with the 100 hr BSR transition temperature given in parenthesis, the fibers ranked: Sylramic (1261{degrees}C), Nicalon S (1256{degrees}C), annealed Hi Nicalon (1215{degrees}C), Hi Nicalon (1078{degrees}C), Nicalon CG (1003{degrees}C) and Tyranno E (932{degrees}C). The thermal creep for Sylramic, Nicalon S, Hi Nicalon and Nicalon CG fibers in a 5000 hr irradiation creep BSR test is projected from the temperature dependence of the m-curves determined during 1 and 100 hr BSR control tests.

  3. The effect of temperature and stress on creep behavior of ultrafine grained nanocrystalline Ni-3 at% Zr alloy

    Science.gov (United States)

    Meraj, Md.; Pal, Snehanshu

    2017-02-01

    In this paper, molecular dynamics (MD) simulation based study of creep behavior for nanocrystalline (NC) Ni-3 at% Zr alloy having grain size 6 nm has been performed using embedded atom method (EAM) potential to study the influence of variation of temperature (1220-1450 K) as well as change in stress (0.5-1.5 GPa) on creep behavior. All the simulated creep curves for this ultra-fine grained NC Ni-Zr alloy has extensive tertiary creep regime. Primary creep regime is very short and steady state creep part is almost absent. The effect of temperatures and stress is prominent on the nature of the simulated creep curves and corresponding atomic configurations. Additionally, mean square displacement calculation has been performed at 1220 K, 1250 K, 1350 K, and 1450 K temperatures to correlate the activation energy of atomic diffusion and creep. The activation energy of creep process found to be less compared to activation energies of self-diffusion for Ni and Zr in NC Ni-3 at% Zr alloy. Formation of martensite is identified during creep process by common neighbour analysis. Presence of dislocations is observed only in primary regime of creep curve up till 20 ps, as evident from calculated dislocation density through MD simulations. Coble creep is found to be main operative mechanism for creep deformation of ultrafine grained NC Ni-3 at% Zr alloy.

  4. Matrix cracking and creep behavior of monolithic zircon and zircon silicon carbide fiber composites

    Science.gov (United States)

    Anandakumar, Umashankar

    In this study, the first matrix cracking behavior and creep behavior of zircon matrix silicon carbide fiber composites were studied, together with the fracture and creep behavior of the monolithic zircon. These behaviors are of engineering and scientific importance, and the study was aimed at understanding the deformation mechanisms at elevated temperatures. The first matrix cracking behavior of zircon matrix uniaxially reinforced with silicon carbide fiber (SCS-6) composites and failure behavior of monolithic zircon were studied as a function of temperature (25°C, 500°C, and 1200°C) and crack length in three point bending mode. A modified vicker's indentation technique was used to vary the initial crack length in monolithic and composite samples. The interfacial shear strength was measured at these temperatures from matrix crack saturation spacing. The composites exhibited steady state and non steady state behaviors at the three different temperatures as predicted by theoretical models, while the failure stress of zircon decreased with increasing stress. The intrinsic properties of the composites were used to numerically determine the results predicted by three different matrix cracking models based on a fracture mechanics approach. The analysis showed that the model based on crack bridging analysis was valid at 25°C and 500°C, while a model based on statistical fiber failure was valid at 1200°C. Microstructural studies showed that fiber failure in the crack wake occurred at or below the matrix cracking stress at 1200°C, and no fiber failure occurred at the other two temperatures, which validated the results predicted by the theoretical models. Also, it was shown that the interfacial shear stress corresponding to debonding determined the matrix cracking stress, and not the frictional shear stress. This study showed for the first time, the steady state and non-steady state matrix cracking behavior at elevated temperatures, the difference in behavior between

  5. Prediction of long-term creep behavior and lifetime of PPC pipe materials by linear extrapolation

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The universal creep equation relates creep behavior(ε/εo)to aging time(ta),coefficient of retardation time(β),and intrinsic time(to).The relation was used to treat the creep experimental data for pipe specimens of polypropylene block copelymer(PPC),which were aged for different days(short-term)and tested under different stress levels at a certain temperature.Then unified master lines were constructed with the treated data and curves according to the universal equation.The master straight lines can be used for extrapolation to predict the long-term creep behavior and lifetime of the pipe materials of PPC in the same way as plate materials.

  6. Creep behavior of alloy 617 in high temperature air and helium environments-effect of oxidation damage

    Energy Technology Data Exchange (ETDEWEB)

    Jang, Chang Heui; Kim, Sung Hwan [Dept. of Nuclear and Quantum Engineering, Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Sah, Injin; Kim, Dae Jong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    The creep behavior of a nickel-base superalloy, Alloy 617, which is considered as a candidate material for the very high temperature gas cooled reactor, was studied. Creep rupture tests were carried out at 800°C, 900°C and 1000°C in static and flowing helium environments as well as in air. Creep rupture life in static helium was longer than that in air, while it was shorter in flowing helium environments. Microstructure observation of the creep tested specimens showed that the shorter creep rupture life in flowing helium was associated with the thicker oxide layer, greater decarburization depth, and deeper internal oxidation happened during the creep tests. The degree of such oxidation damage was quantified for the creep tested specimens and correlated with the creep rupture life in different environments.

  7. Microstructure and creep behavior of magnesium-aluminum alloys containing alkaline and rare earth additions

    Science.gov (United States)

    Saddock, Nicholas David

    In the past few decades governmental regulation and consumer demands have lead the automotive companies towards vehicle lightweighting. Powertrain components offer significant potential for vehicle weight reductions. Recently, magnesium alloys have shown promise for use in powertrain applications where creep has been a limiting factor. These systems are Mg-Al based, with alkaline earth or rare earth additions. The solidification, microstructure, and creep behavior of a series of Mg-4 Al- 4 X:(Ca, Ce, La, and Sr) alloys and a commercially developed AXJ530 (Mg--5 Al--3 Ca--0.15 Sr) alloy (by wt%) have been investigated. The order of decreasing freezing range of the five alloys was: AX44, AXJ530, AJ44, ALa44 and ACe44. All alloys exhibited a solid solution primary alpha-Mg phase surrounded by an interdendritic region of Mg and intermetallic(s). The primary phase was composed of grains approximately an order of magnitude larger than the cellular structure. All alloys were permanent mold cast directly to creep specimens and AXJ530 specimens were provided in die-cast form. The tensile creep behavior was investigated at 175 °C for stresses ranging from 40 to 100 MPa. The order of decreasing creep resistance was: die-cast AXJ530 and permanent mold cast AXJ530, AX44, AJ44, ALa44 and ACe44. Grain size, solute concentration, and matrix precipitates were the most significant microstructural features that influenced the creep resistance. Decreases in grain size or increases in solute concentration, both Al and the ternary addition, lowered the minimum creep rate. In the Mg-Al-Ca alloys, finely distributed Al2Ca precipitates in the matrix also improved the creep resistance by a factor of ten over the same alloy with coarse precipitates. The morphology of the eutectic region was distinct between alloys but did not contribute to difference in creep behavior. Creep strain distribution for the Mg-Al-Ca alloys developed heterogeneously on the scale of the alpha-Mg grains. As

  8. Creep behavior for advanced polycrystalline SiC fibers

    Energy Technology Data Exchange (ETDEWEB)

    Youngblood, G.E.; Jones, R.H. [Pacific Northwest National Lab., Richland, WA (United States); Kohyama, Akira [Kyoto Univ. (Japan)] [and others

    1997-04-01

    A bend stress relaxation (BSR) test has been utilized to examine irradiation enhanced creep in polycrystalline SiC fibers which are under development for use as fiber reinforcement in SiC/SiC composite. Qualitative, S-shaped 1hr BSR curves were compared for three selected advanced SiC fiber types and standard Nicalon CG fiber. The temperature corresponding to the middle of the S-curve (where the BSR parameter m = 0.5) is a measure of a fiber`s thermal stability as well as it creep resistance. In order of decreasing thermal creep resistance, the measured transition temperatures were Nicalon S (1450{degrees}C), Sylramic (1420{degrees}C), Hi-Nicalon (1230{degrees}C) and Nicalon CG (1110{degrees}C).

  9. Constitutive modeling of creep behavior in single crystal superalloys: Effects of rafting at high temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Fan, Ya-Nan, E-mail: fanyn12@mails.tsinghua.edu.cn; Shi, Hui-Ji, E-mail: shihj@mail.tsinghua.edu.cn; Qiu, Wen-Hui

    2015-09-17

    Rafting and creep modeling of single crystal superalloys at high temperatures are important for the safety assessment and life prediction in practice. In this research, a new model has been developed to describe the rafting evolution and incorporated into the Cailletaud single crystal plasticity model to simulate the creep behavior. The driving force of rafting is assumed to be the relaxation of the strain energy, and it is calculated with the local stress state, a superposition of the external and misfit stress tensors. In addition, the isotropic coarsening is introduced by the cube root dependence of the microstructure periodicity on creep time based on Ostwal ripening. Then the influence of rafting on creep deformation is taken into account as the Orowan stress in the single crystal plasticity model. The capability of the proposed model is validated with creep experiments of CMSX-4 at 950 °C and 1050 °C. It is able to predict the rafting direction at complex loading conditions and evaluate the channel width during rafting. For [001] tensile creep tests, good agreement has been shown between the model predictions and experimental results at different temperatures and stress levels. The creep acceleration can be captured with this model and is attributed to the microstructure degradation caused by the precipitate coarsening.

  10. The primary creep behavior of single crystal, nickel base superalloys PWA 1480 and PWA 1484

    Science.gov (United States)

    Wilson, Brandon Charles

    Primary creep occurring at intermediate temperatures (650°C to 850°C) and loads greater than 500 MPa has been shown to result in severe creep strain, often exceeding 5-10%, during the first few hours of creep testing. This investigation examines how the addition of rhenium and changes in aging heat treatment affect the primary creep behavior of PWA 1480 and PWA 1484. To aid in the understanding of rhenium's role in primary creep, 3wt% Re was added to PWA 1480 to create a second generation version of PWA 1480. The age heat treatments used for creep testing were either 704°C/24 hr. or 871°C/32hr. All three alloys exhibited the presence of secondary gamma' confirmed by scanning electron microscopy and local electrode atom probe techniques. These aging heat treatments resulted in the reduction of the primary creep strain produced in PWA 1484 from 24% to 16% at 704°C/862 MPa and produced a slight dependence of the tensile properties of PWA 1480 on aging heat treatment temperature. For all test temperatures, the high temperature age resulted in a significant decrease in primary creep behavior of PWA 1484 and a longer lifetime for all but the lowest test temperature. The primary creep behavior of PWA 1480 and PWA 1480+Re did not display any significant dependence on age heat treatment. The creep rupture life of PWA 1480 is greater than PWA 1484 at 704°C, but significantly shorter at 760°C and 815°C. PWA 1480+Re, however, displayed the longest lifetime of all three alloys at both 704°C and 815°C (PWA 1480+Re was not tested at 760°C). Qualitative TEM analysis revealed that PWA 1484 deformed by large dislocation "ribbons" spanning large regions of material. PWA 1480, however, deformed primarily due to matrix dislocations and the creation of interfacial dislocation networks between the gamma and gamma' phases. PWA 1480+ contained stacking faults as well, though they acted on multiple slip systems generating work hardening and forcing the onset of secondary creep. X

  11. Creep Behavior of High Temperature Alloys for Generation IV Nuclear Energy Systems

    Science.gov (United States)

    Wen, Xingshuo

    The Very High Temperature Reactor (VHTR) is one of the leading concepts of the Generation IV nuclear reactor development, which is the core component of Next Generation Nuclear Plant (NGNP). The major challenge in the research and development of NGNP is the performance and reliability of structure materials at high temperature. Alloy 617, with an exceptional combination of high temperature strength and oxidation resistance, has been selected as a primary candidate material for structural use, particularly in Intermediate Heat Exchanger (IHX) which has an outlet temperature in the range of 850 to 950°C and an inner pressure from 5 to 20MPa. In order to qualify the material to be used at the operation condition for a designed service life of 60 years, a comprehensive scientific understanding of creep behavior at high temperature and low stress regime is necessary. In addition, the creep mechanism and the impact factors such as precipitates, grain size, and grain boundary characters need to be evaluated for the purpose of alloy design and development. In this study, thermomechanically processed specimens of alloy 617 with different grain sizes were fabricated, and creep tests with a systematic test matrix covering the temperatures of 850 to 1050°C and stress levels from 5 to 100MPa were conducted. Creep data was analyzed, and the creep curves were found to be unconventional without a well-defined steady-state creep. Very good linear relationships were determined for minimum creep rate versus stress levels with the stress exponents determined around 3-5 depending on the grain size and test condition. Activation energies were also calculated for different stress levels, and the values are close to 400kJ/mol, which is higher than that for self-diffusion in nickel. Power law dislocation climb-glide mechanism was proposed as the dominant creep mechanism in the test condition regime. Dynamic recrystallization happening at high strain range enhanced dislocation climb and

  12. Creep-fatigue behavior of turbine disc of superalloy GH720Li at 650 °C and probabilistic creep-fatigue modeling

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Dianyin [School of Energy and Power Engineering, Beihang University, Beijing 100191 (China); Collaborative Innovation Center of Advanced Aero-Engine, Beijing 100191 (China); Beijing Key Laboratory of Aero-Engine Structure and Strength, Beijing 100191 (China); Ma, Qihang [School of Energy and Power Engineering, Beihang University, Beijing 100191 (China); Shang, Lihong [Mining and Materials Engineering, McGill University, Montreal, QC H3A 0C5 (Canada); Gao, Ye [School of Energy and Power Engineering, Beihang University, Beijing 100191 (China); Wang, Rongqiao, E-mail: wangrq@buaa.edu.cn [School of Energy and Power Engineering, Beihang University, Beijing 100191 (China); Collaborative Innovation Center of Advanced Aero-Engine, Beijing 100191 (China); Beijing Key Laboratory of Aero-Engine Structure and Strength, Beijing 100191 (China)

    2016-07-18

    Creep-fatigue experiments have been conducted in nickel-based superalloy GH720Li at an elevated temperature of 650 °C with a stress ratio of 0.1, based on which, different dwell times at the maximum loading were applied to investigate the effect of dwell time on the creep-fatigue behaviors. The tested specimens were cut from the rim region of an actual turbine disc in the hoop direction. The grain size and precipitates of the GH720Li superalloy were examined through scanning electronic microscope (SEM) and energy-dispersive X-ray spectroscopy (EDS) analyses. Experimental data shows creep-fatigue lifetime decreases as the dwell time prolongs. Further, different scattering was observed in the creep-fatigue lifetime at different dwell times. Then a probabilistic model based on the applied mechanical work density (AMWD), with a linear heteroscedastic function that evaluates the non-constant deviation in the creep-fatigue lifetime, was formulated to describe the dependence of creep-fatigue lifetime on the dwell time. Finally, the possible microscopic mechanism of the creep-fatigue behavior has been discussed by SEM with EDS on the fracture surfaces.

  13. Creep testing and viscous behavior research on carbon constructional quality steel under high temperature

    Institute of Scientific and Technical Information of China (English)

    余敏; 罗迎社; 彭相华

    2008-01-01

    Creep tests under at a certain temperature and different stress levels were performed on two carbon constructional quality steels at a certain stress level and different temperatures,and their creep curves at high temperature were obtained based on analyzing the testing data.Taking 45 steel at a certain temperature and stress as the example,the integral creep constitutive equation and the differential stress-strain constitutive relationship were established based on the relevant rheological model,and the integral core function was also obtained.Simultaneously,the viscous coefficients denoting the viscous behavior in visco-plastic constitutive equation were determined by taking use of the creep testing data.Then the viscous coefficients of three carbon steels(20 steel,35 steel and 45 steel) were compared and analyzed.The results show that the viscosity is different due to different materials at the same temperature and stress.

  14. Creep behavior of oxide dispersion strengthened 8Cr-2WVTa and 8Cr-1W steels

    Energy Technology Data Exchange (ETDEWEB)

    Shinozuka, K. [Department of Material Science and Engineering, National Defense Academy, Yokosuka, Kanagawa 239-8686 (Japan)], E-mail: kshinozu@nda.ac.jp; Tamura, M.; Esaka, H. [Department of Material Science and Engineering, National Defense Academy, Yokosuka, Kanagawa 239-8686 (Japan); Shiba, K.; Nakamura, K. [Japan Atomic Energy Agency, Tokai-mura, Naka-Gun, Ibaraki 319-1195 (Japan)

    2009-01-31

    Microstructures and creep behavior of two martensitic oxide dispersion strengthened (ODS) steels 8%Cr-2%W-0.2%V-0.1%Ta (J1) and 8%Cr-1%W (J2) with finely dispersed Y{sub 2}Ti{sub 2}O{sub 7} have been investigated. Creep tests have been carried out at 670, 700 and 730 deg. C. Creep strength of J1 is stronger than that of any other ODS martensitic steels and the hoop strength of the ferritic ODS steel cladding. At the beginning of creep test, shrinkage was frequently observed for J1. This is one of the reasons for high creep strength of J1. The {delta}-ferrite, which is untransformed to austenite at hot isostatic press and hot rolling temperatures, was elongated along the rolling direction, and volume fraction of {delta}-ferrite in J1 is larger than J2. Although the elongated {delta}-ferrite affects the anisotropy of creep behavior, the extent of anisotropy in J1 is not so large as that of the ferritic ODS steel.

  15. A Modified Theta Projection Model for Creep Behavior of Metals and Alloys

    Science.gov (United States)

    Kumar, Manish; Singh, I. V.; Mishra, B. K.; Ahmad, S.; Venugopal Rao, A.; Kumar, Vikas

    2016-09-01

    In this work, a modified theta projection model is proposed for the constitutive modeling of creep behavior of metals and alloys. In the conventional theta projection model, strain hardening exponent is a function of time and theta, whereas in the modified theta projection model, the exponent is taken as a function of time, theta, and applied stress. The results obtained by the modified theta projection model for Al 2124 T851 alloy at constant uniaxial tensile stress are compared with the experimental results and with the predictions of the conventional theta projection method. The creep behavior of Al 7075 T651 alloy is also predicted using modified and conventional theta projection model and compared with the available experimental data. It is observed that the modified theta projection model captures the creep behavior more accurately as compared to the conventional theta projection model. The modified theta projection model can be used to predict the creep strain of pure metals and class M alloys (similar creep behavior to pure metals) for intermediate range of stress and temperature.

  16. Effect of matrix cracking on the time delayed buckling of viscoelastic laminated circular cylindrical shells

    Institute of Scientific and Technical Information of China (English)

    PENG Fan; FU YiMing; CHEN YaoJun

    2008-01-01

    The effect of matrix cracking on the bifurcation creep buckling of viscoelastic laminated circular cylindrical shells is investigated. The viscoelastic behavior of laminas is modeled by Schapery's integral constitutive equation with growing ma-trix cracks. The values of damage variables are correlated to non-dimensional density of matrix cracks relying on the formulas from meso-mechanics approach, and the evolution equation predicting the growth rate of density of matrix cracks is assumed to follow a power type relation with transverse tensile stress. The gov-erning equations for pre-buckling creep deformation and bifurcation buckling of laminated circular cylindrical shells under axial compression are obtained on the basis of the Donnell type shallow shell theory and Karman-Donnell geometrically nonlinear relationship. Corresponding solution strategy is constructed by inte-grating finite-difference technique, trigonometric series expansion method and Taylor's numerical recursive scheme for convolution integration. The bifurcation creep buckling of symmetrically laminated glass-epoxy circular cylindrical shells with matrix creep cracking coupled are examined for various geometrical parame-ters and parameters of damage evolution as well as boundary conditions. The nu-merical results show that matrix creep cracking remarkably shortens the critic time of bifurcation buckling and reduces the durable critic loads, and its effects become weak and finally vanish with the increase of the ratio of radius to thickness in the case of short laminated circular cylindrical shells, also the influence of the matrix creep cracking is mainly dependent on the boundary conditions at two ends for moderately long circular cylindrical shells.

  17. Local buckling behavior of 48', X80 high-strain line pipes

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Nobuhisa; Tajika, Hisakazu; Igi, Satoshi; Okatsu, Mitsuru; Kondo, Joe; Arakawa, Takekazu [JFE Steel Corporation (Japan)

    2010-07-01

    In the natural gas sector, more and more long distance and high pressure pipelines are now constructed in challenging areas, such as seismic and Arctic regions. In order to provide safe and reliable operations, high strength, high strain and large diameter pipes are used in such projects to withstand the important strains induced by the environment. The aim of this paper is to investigate the local buckling behavior of high strength and large diameter line pipes. A bending test apparatus was developed and used to perform 2 bending tests on X80 grade, 48'' pipes pressurized to 60% SMYS and a finite element analysis (FEA) was conducted. The comparison between experimental results and simulations showed that the FEA was successful in predicting bending moment, displacement and longitudinal strain. This paper demonstrated the FEA can be used to determine the behavior of high strength, high strain and large diameter pipes.

  18. Creep behavior of hand-mixed Simplex P bone cement under cyclic tensile loading.

    Science.gov (United States)

    Verdonschot, N; Huiskes, R

    1994-01-01

    Acrylic cement, used for the fixation of total hip replacements and other orthopedic implants, is a subject of renewed scientific interest as a result of recent hypotheses about dynamic, long-term mechanical failure mechanisms suspected to play a role in prosthetic loosening. Little is known, however, about the long-term mechanical behavior of cement. In this study, the dynamic creep deformation of hand mixed acrylic cement was examined in laboratory tests. Strain patterns found represented the familiar creep process consisting of a primary, a secondary, and a tertiary creep phase. Specimens dynamically loaded with a maximum stress of 3 MPa from 0 were subject to creep of about 50% of the elastic strain after 250 000 loading cycles. A linear relationship between the logarithmic values of the creep-strain and the number of loading cycles was found. Specimens exposed to higher loads showed significantly higher creep-strains. No relationship could be established between the strain levels and the porosity of the specimens. Specimens dynamically loaded with a maximal stress of 7 or 11 MPa from 0 failed during the tests. The number of loading cycles to failure was similar to fatigue strength data reported in earlier literature.

  19. Influence of dispersoids on the creep behavior of dispersion strengthened aluminum materials

    OpenAIRE

    Carreño, F.; O.A. Ruano

    1997-01-01

    The creep behavior of a rapidly solidified Al-6.5%Fe-0.6%V-1.3%Si dispersion strengthened material containing 16 volume % of dispersoids has been studied by means of tensile tests at high temperatures from 483 to 821 K. The imposed strain rates ranged from 2.5∙10-6 to 10-2s-1. The microstructure was very fine, consisting of submicron grains and small hard round-shaped dispersoids of about 54 nm. The creep behavior was charac...

  20. On the Through-the-Width Multiple Delamination, and Buckling and Postbuckling Behaviors of Symmetric and Unsymmetric Composite Laminates

    Science.gov (United States)

    Liu, P. F.; Zheng, J. Y.

    2013-12-01

    Multiple delamination causes severe degradation of the stiffness and strength of composites. Interactions between multiple delamination, and buckling and postbuckling under compressive loads add the complexity of mechanical properties of composites. In this paper, the buckling, postbuckling and through-the-width multiple delamination of symmetric and unsymmetric composite laminates are studied using 3D FEA, and the virtual crack closure technique with two delamination failure criteria: B-K law and power law is used to predict the delamination growth and to calculate the mixed-mode energy release rate. The compressive load-strain curves, load-central deflection curves and multiple delamination process for eight composite specimens with different initial delamination sizes and their distributions as well as two angle-ply configurations 04//(± θ)6//04 ( θ = 0° and 45°, and "//" denotes the delaminated interface) are comparatively studied. From numerical results, the unsymmetry decreases the local buckling load and initial delamination load, but does not affect the global buckling load compared with the symmetric laminates. Besides, the unsymmetry affects the unstable delamination and buckling behaviors of composite laminates largely when the initial multiple delamination sizes are relatively small.

  1. INFLUENCE OF CHEMICAL CROSS-LINKING ON THE CREEP-BEHAVIOR OF ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE FIBERS

    NARCIS (Netherlands)

    PENNING, JP; PRAS, HE; PENNINGS, AJ

    1994-01-01

    In this study, the effect of chemical crosslinking on the creep behavior of high-strength fibers, obtained by gel-spinning and subsequent hot-drawing of ultra-high molecular weight polyethylene (UHMWPE), is examined. In the first part of the paper, the general aspects of the creep behavior of these

  2. Phase Transformation and Creep Behavior in Ti50Pd30Ni20 High Temperature Shape Memory Alloy in Compression

    Science.gov (United States)

    Kumar, Parikshith K.; Desai, Uri; Monroe, James; Lagoudas, Dimitris C.; Karaman, Ibrahim; Noebe, Ron; Bigelow, Glenn

    2010-01-01

    The creep behavior and the phase transformation of Ti50Pd30Ni20 High Temperature Shape Memory Alloy (HTSMA) is investigated by standard creep tests and thermomechanical tests. Ingots of the alloy are induction melted, extruded at high temperature, from which cylindrical specimens are cut and surface polished. A custom high temperature test setup is assembled to conduct the thermomechanical tests. Following preliminary monotonic tests, standard creep tests and thermally induced phase transformation tests are conducted on the specimen. The creep test results suggest that over the operating temperatures and stresses of this alloy, the microstructural mechanisms responsible for creep change. At lower stresses and temperatures, the primary creep mechanism is a mixture of dislocation glide and dislocation creep. As the stress and temperature increase, the mechanism shifts to predominantly dislocation creep. If the operational stress or temperature is raised even further, the mechanism shifts to diffusion creep. The thermally induced phase transformation tests show that actuator performance can be affected by rate independent irrecoverable strain (transformation induced plasticity + retained martensite) as well as creep. The rate of heating and cooling can adversely impact the actuators performance. While the rate independent irrecoverable strain is readily apparent early in the actuators life, viscoplastic strain continues to accumulate over the lifespan of the HTSMA. Thus, in order to get full actuation out of the HTSMA, the heating and cooling rates must be sufficiently high enough to avoid creep.

  3. Phase Transformation and Creep Behavior in Ti50Pd30Ni20 High Temperature Shape Memory Alloy in Compression

    Science.gov (United States)

    Kumar, Parikshith K.; Desai, Uri; Monroe, James; Lagoudas, Dimitris C.; Karaman, Ibrahim; Noebe, Ron; Bigelow, Glenn

    2010-01-01

    The creep behavior and the phase transformation of Ti50Pd30Ni20 High Temperature Shape Memory Alloy (HTSMA) is investigated by standard creep tests and thermomechanical tests. Ingots of the alloy are induction melted, extruded at high temperature, from which cylindrical specimens are cut and surface polished. A custom high temperature test setup is assembled to conduct the thermomechanical tests. Following preliminary monotonic tests, standard creep tests and thermally induced phase transformation tests are conducted on the specimen. The creep test results suggest that over the operating temperatures and stresses of this alloy, the microstructural mechanisms responsible for creep change. At lower stresses and temperatures, the primary creep mechanism is a mixture of dislocation glide and dislocation creep. As the stress and temperature increase, the mechanism shifts to predominantly dislocation creep. If the operational stress or temperature is raised even further, the mechanism shifts to diffusion creep. The thermally induced phase transformation tests show that actuator performance can be affected by rate independent irrecoverable strain (transformation induced plasticity + retained martensite) as well as creep. The rate of heating and cooling can adversely impact the actuators performance. While the rate independent irrecoverable strain is readily apparent early in the actuators life, viscoplastic strain continues to accumulate over the lifespan of the HTSMA. Thus, in order to get full actuation out of the HTSMA, the heating and cooling rates must be sufficiently high enough to avoid creep.

  4. Time-Dependent Behaviors of Granite: Loading-Rate Dependence, Creep, and Relaxation

    Science.gov (United States)

    Hashiba, K.; Fukui, K.

    2016-07-01

    To assess the long-term stability of underground structures, it is important to understand the time-dependent behaviors of rocks, such as their loading-rate dependence, creep, and relaxation. However, there have been fewer studies on crystalline rocks than on tuff, mudstone, and rock salt, because the high strength of crystalline rocks makes the detection of their time-dependent behaviors much more difficult. Moreover, studies on the relaxation, temporal change of stress and strain (TCSS) conditions, and relations between various time-dependent behaviors are scarce for not only granites, but also other rocks. In this study, previous reports on the time-dependent behaviors of granites were reviewed and various laboratory tests were conducted using Toki granite. These tests included an alternating-loading-rate test, creep test, relaxation test, and TCSS test. The results showed that the degree of time dependence of Toki granite is similar to other granites, and that the TCSS resembles the stress-relaxation curve and creep-strain curve. A viscoelastic constitutive model, proposed in a previous study, was modified to investigate the relations between the time-dependent behaviors in the pre- and post-peak regions. The modified model reproduced the stress-strain curve, creep, relaxation, and the results of the TCSS test. Based on a comparison of the results of the laboratory tests and numerical simulations, close relations between the time-dependent behaviors were revealed quantitatively.

  5. NONLINEAR BUCKLING BEHAVIOR OF DAMAGED COMPOSITE SANDWICH PLATES CONSIDERING THE EFFECT OF TEMPERATURE-DEPENDENT THERMAL AND MECHANICAL PROPERTIES

    Institute of Scientific and Technical Information of China (English)

    Bai Ruixiang; Chen Haoran

    2001-01-01

    On the basis of the first-order shear deformation plate theory and the zig-zag deformation assumption, an incremental finite element formulation for nonlinear buckling analysis of the composite sandwich plate is deduced and the temperature-dependent thermal and mechanical properties of composite is considered. A finite element method for thermal or thermo-mechanical coupling nonlinear buckling analysis of the composite sandwich plate with an interfacial crack damage between face and core is also developed. Numerical results and discussions concerning some typical examples show that the effects of the variation of the thermal and mechanical properties with temperature, extermal compressive loading, size of the damage zone and piy angle of the faces on the thermal buckling behavior are significant.

  6. In-Plane Elastic Buckling of Arch

    Institute of Scientific and Technical Information of China (English)

    剧锦三; 郭彦林

    2002-01-01

    The in-plane elastic buckling behavior of arches is investigated using a new finite-element approach for the nonlinear analysis. The linear buckling, nonlinear primary buckling, and secondary bifurcation buckling behavior of arches are compared taking into account the large deformation and the effects of initial geometric imperfections or perturbations. The theoretical investigation emphasizes the nonlinear secondary bifurcation buckling behavior for a full span uniformly distributed load. The efficiency of compact method for tracing secondary buckling path is shown through several examples. Finally, a new structural design, which prevents the secondary bifurcation buckling by adding some crossed cables across the arch, is proposed to improve the limit load carrying capacity.

  7. Laminate Analyses, Micromechanical Creep Response, and Fatigue Behavior of Polymer Matrix Composite Materials.

    Science.gov (United States)

    1982-12-01

    FATIGUE BEHAVIOR of POLYMER MATRIX COMPOSITE MATERIALS , 4 " .’* .. . . ". ... .. ... . . ~December 1982 41 .. FINAL REPORT .Army Research Office I I...DEPARTMENT REPORT UWME-DR-201-108-1 LAMINATE ANALYSES, MICROMECHANICAL CREEP RESPONSE, AND FATIGUE BEHAVIOR OF POLYMER MATRIX COMPOSITE MATERIALS...Behavior of Polymer Matrix Composite 16 Sept. 1979 - 30 Nov. 1982 Materials 6 PERFORMING ORG. REPORT NUMBER UWME-DR-201-108-1 7. AUTHOR(.) S. CONTRACT

  8. Behavior of Repeating Earthquake Sequences in Central California and the Implications for Subsurface Fault Creep

    Energy Technology Data Exchange (ETDEWEB)

    Templeton, D C; Nadeau, R; Burgmann, R

    2007-07-09

    Repeating earthquakes (REs) are sequences of events that have nearly identical waveforms and are interpreted to represent fault asperities driven to failure by loading from aseismic creep on the surrounding fault surface at depth. We investigate the occurrence of these REs along faults in central California to determine which faults exhibit creep and the spatio-temporal distribution of this creep. At the juncture of the San Andreas and southern Calaveras-Paicines faults, both faults as well as a smaller secondary fault, the Quien Sabe fault, are observed to produce REs over the observation period of March 1984-May 2005. REs in this area reflect a heterogeneous creep distribution along the fault plane with significant variations in time. Cumulative slip over the observation period at individual sequence locations is determined to range from 5.5-58.2 cm on the San Andreas fault, 4.8-14.1 cm on the southern Calaveras-Paicines fault, and 4.9-24.8 cm on the Quien Sabe fault. Creep at depth appears to mimic the behaviors seen of creep on the surface in that evidence of steady slip, triggered slip, and episodic slip phenomena are also observed in the RE sequences. For comparison, we investigate the occurrence of REs west of the San Andreas fault within the southern Coast Range. Events within these RE sequences only occurred minutes to weeks apart from each other and then did not repeat again over the observation period, suggesting that REs in this area are not produced by steady aseismic creep of the surrounding fault surface.

  9. Combined-load buckling behavior of metal-matrix composite sandwich panels under different thermal environments

    Science.gov (United States)

    Ko, William L.; Jackson, Raymond H.

    1991-01-01

    Combined compressive and shear buckling analysis was conducted on flat rectangular sandwich panels with the consideration of transverse shear effects of the core. The sandwich panel is fabricated with titanium honeycomb core and laminated metal matrix composite face sheets. The results show that the square panel has the highest combined load buckling strength, and that the buckling strength decreases sharply with the increases of both temperature and panel aspect ratio. The effect of layup (fiber orientation) on the buckling strength of the panels was studied in detail. The metal matrix composite sandwich panel was much more efficient than the sandwich panel with nonreinforced face sheets and had the same specific weight.

  10. Uniqueness of rate-dependency, creep and stress relaxation behaviors for soft clays

    Institute of Scientific and Technical Information of China (English)

    朱启银; 尹振宇; 徐长节; 殷建华; 夏小和

    2015-01-01

    This work focuses on the uniqueness of rate-dependency, creep and stress relaxation behaviors for soft clays under one-dimensional condition. An elasto-viscoplastic model is briefly introduced based on the rate-dependency of preconsolidation pressure. By comparing the rate-dependency formulation with the creep based formulation, the relationship between rate-dependency and creep behaviors is firstly described. The rate-dependency based formulation is then extended to derive an analytical solution for the stress relaxation behavior with defining a stress relaxation coefficient. Based on this, the relationship between the rate-dependency coefficient and the stress relaxation coefficient is derived. Therefore, the uniqueness between behaviors of rate-dependency, creep and stress relaxation with their key parameters is obtained. The uniqueness is finally validated by comparing the simulated rate-dependency of preconsolidation pressure, the estimated values of secondary compression coefficient and simulations of stress relaxation tests with test results on both reconstituted Illite and Berthierville clay.

  11. Effect of resin variables on the creep behavior of high density hardwood composite panels

    Science.gov (United States)

    R.C. Tang; Jianhua Pu; C.Y Hse

    1993-01-01

    The flexural creep behavior of oriented strandboards (OSB) fabricated with mixed high, density hardwood flakes was investigated. Three types of adhesives, liquid phenolic-formaldehyde (LPF), melamine modified urea-formaldehyde (MUF), and LPF (face)/MUF (core) were chosen in this investigation. The resin contents (RC) used were 3.5 percent and 5.0 percent. The flakes...

  12. Effect of Nanoclay on the Flexural Creep Behavior of Wood/Plastic Composites

    Science.gov (United States)

    Kord, B.; Sheykholeslami, A.; Najafi, A.

    2016-01-01

    The effect of nanoclay on the short-term flexural creep behavior of polypropylene/wood flour composites was investigated. The results obtained showed that the flexural strength and modulus increased with contentt of nanoclay up to 3 phc and then decreased. The fractional deflection and relative creep decreased with increasing content of nanoclay. X-ray diffraction patterns and transmission electron microscopy revealed that the nanocomposites formed were intercalated. Morphological findings testified that the samples containing 3 phc of nanoclay had the highest degree of intercalation and dispersion.

  13. Cyclic compressive creep-elastoplastic behaviors of in situ TiB{sub 2}/Al-reinforced composite

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Qing [School of Mechanical Engineering, Beijing Institute of Technology, 100081 (China); Zhang, Weizheng, E-mail: zhangwz@bit.edu.cn [School of Mechanical Engineering, Beijing Institute of Technology, 100081 (China); Liu, Youyi [School of Mechanical Engineering, State University of New York at Stony Brook, NY 11790 (United States); Guo, BingBin [School of Mechanical Engineering, Beijing Institute of Technology, 100081 (China)

    2016-06-01

    This paper presents a study on the cyclic compressive creep-elastoplastic behaviors of a TiB{sub 2}-reinforced aluminum matrix composite (ZL109) at 350 °C and 200 °C. According to the experimental results, under cyclic elastoplasticity and cyclic coupled compressive creep-elastoplasticity, the coupled creep will cause changes in isotropic stress and kinematic stress. Isotropic stress decreases with coupled creep, leading to cyclic softening. Positive kinematic stress, however, increases with coupled creep, leading to cyclic hardening. Transmission electron microscopy (TEM) observations of samples under cyclic compressive creep-elastoplasticity with different temperatures and strain amplitudes indicate that more coupled creep contributes to more subgrain boundaries but fewer intracrystalline dislocations. Based on the macro tests and micro observations, the micro mechanism of compressive creep's influence on cyclic elastoplasticity is elucidated. Dislocations recovering with coupled creep leads to isotropic softening, whereas subgrain structures created by coupled creep lead to kinematic hardening during cyclic deformation.

  14. Creep Behavior of High-Strength Concrete Subjected to Elevated Temperatures

    Directory of Open Access Journals (Sweden)

    Minho Yoon

    2017-07-01

    Full Text Available Strain is generated in concrete subjected to elevated temperatures owing to the influence of factors such as thermal expansion and design load. Such strains resulting from elevated temperatures and load can significantly influence the stability of a structure during and after a fire. In addition, the lower the water-to-binder (W–B ratio and the smaller the quantity of aggregates in high-strength concrete, the more likely it is for unstable strain to occur. Hence, in this study, the compressive strength, elastic modulus, and creep behavior were evaluated at target temperatures of 100, 200, 300, 500, and 800 °C for high-strength concretes with W–B ratios of 30%, 26%, and 23%. The loading conditions were set as non-loading and 0.33fcu. It was found that as the compressive strength of the concrete increased, the mechanical characteristics deteriorated and transient creep increased. Furthermore, when the point at which creep strain occurred at elevated temperatures after the occurrence of transient creep was considered, greater shrinkage strain occurred as the compressive strength of the concrete increased. At a heating temperature of 800 °C, the 80 and 100 MPa test specimens showed creep failure within a shrinkage strain range similar to the strain at the maximum load.

  15. Creep Behavior of High-Strength Concrete Subjected to Elevated Temperatures.

    Science.gov (United States)

    Yoon, Minho; Kim, Gyuyong; Kim, Youngsun; Lee, Taegyu; Choe, Gyeongcheol; Hwang, Euichul; Nam, Jeongsoo

    2017-07-11

    Strain is generated in concrete subjected to elevated temperatures owing to the influence of factors such as thermal expansion and design load. Such strains resulting from elevated temperatures and load can significantly influence the stability of a structure during and after a fire. In addition, the lower the water-to-binder (W-B) ratio and the smaller the quantity of aggregates in high-strength concrete, the more likely it is for unstable strain to occur. Hence, in this study, the compressive strength, elastic modulus, and creep behavior were evaluated at target temperatures of 100, 200, 300, 500, and 800 °C for high-strength concretes with W-B ratios of 30%, 26%, and 23%. The loading conditions were set as non-loading and 0.33fcu. It was found that as the compressive strength of the concrete increased, the mechanical characteristics deteriorated and transient creep increased. Furthermore, when the point at which creep strain occurred at elevated temperatures after the occurrence of transient creep was considered, greater shrinkage strain occurred as the compressive strength of the concrete increased. At a heating temperature of 800 °C, the 80 and 100 MPa test specimens showed creep failure within a shrinkage strain range similar to the strain at the maximum load.

  16. Creep Behavior and Its Influence on the Mechanics of Electrodeposited Nickel Films

    Institute of Scientific and Technical Information of China (English)

    Zengsheng Ma; Shiguo Long; Yong Pan; Yichun Zhou

    2009-01-01

    In order to improve the accuracy and comparability of hardness and elastic modulus measurements in nanoin-dentation, an evaluation of the creep behavior and its influence on the mechanical properties of the electrode-posited nickel film has been conducted. The influence of loading time and hold period on the hardness and elastic modulus results at maximum load 5000 μN has also been examined. It is found that with increasing the loading time, the creep value is decreased. However, the creep value is increased when the hold period is increased. The elastic modulus results are more reliable if the hold period is longer. If the hold period is long enough, the loading time has no remarkable effect on the hardness and elastic modulus measured.

  17. Role of P, S and B on Creep Behavior of Alloy 718

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The doping of phosphorus, sulfur and boron in IN718 superalloy can remarkably influence the creep behavior. The modifications of the minor elements seem not to vary the stress exponent and the influences primarily concentrate on the effective diffusion coefficient. A pronounced beneficial interaction between P and B and a weaker detrimental interaction between P and S have been obtained. The preexponential frequency constant is proved to be strongly related with the creep activation energy because of the so-called compensation effect. The compensation temperature has been determined to be about 1080 K, which corresponds to the transformation temperature from rapidly coarsened γ″ phase to δ phase. It has been proposed that trace elements can influence the effective diffusion coefficient individually or cooperatively, which in turn either retard or speed the creep process.

  18. Simultaneous consolidation and creep

    DEFF Research Database (Denmark)

    Krogsbøll, Anette

    1997-01-01

    Materials that exhibit creep under constant effective stress typically also show rate dependent behavior. The creep deformations and the rate sensitive behavior is very important when engineering and geological problems with large time scales are considered. When stress induced compaction...

  19. Analytical study on creep behavior of a tube of coolant piping system in nuclear power plant. Contract research

    Energy Technology Data Exchange (ETDEWEB)

    Miyazaki, Noriyuki [Kyushu Univ., Fukuoka (Japan); Hagihara, Seiya [Saga Univ., Saga (Japan); Chino, Eiichi; Maeda, Akio [MRI Systems Inc., Tokyo (Japan); Maruyama, Yu; Hashimoto, Kazuichiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-10-01

    During severe accident of a light water reactor (LWR), reactor coolant piping would be damaged when the piping is subjected to high internal pressure and very high temperature due to heat transfer from high-temperature gas and decay heat from wall-deposited fission product (FP), both from degraded core. In such a case, high-temperature fast creep deformation could be the main cause for the pipe failure. For the evaluation of piping integrity during severe accidents, a method to predict such high-temperature fast creep deformation should be developed, using a creep constitutive equation considering tertiary creep behavior which has not been considered well in the pipe failure analyses. In this study, a creep constitutive equation was developed first based on the Kachanov-Ravotnov isotropic damage rule that considers the tertiary creep behavior. JAERI creep tensile test data for both nuclear-grade cold-drawn SUS316N and hot-extruded SUS316 materials were used to determine coefficients of the developed constitutive equation. Using the developed constitutive equation, finite element analyses were performed for local creep deformation of coolant piping under two temperature conditions: uniform temperature and temperature gradient. The analytical results indicated the damage variable being integrated following the evolution of creep damage can indicate pipe wall internal damage condition quantitatively. The damage variable was confirmed further to be able to reproduce the observation in JAERI piping failure tests, that is, pipe failure from the wall outside. (author)

  20. Effect of fiber-matrix adhesion on the creep behavior of CF/PPS composites: temperature and physical aging characterization

    NARCIS (Netherlands)

    Motta Dias, M.H.; Jansen, K.M.B.; Luinge, J.W.; Bersee, H.E.N.; Benedictus, R.

    2016-01-01

    The influence of fiber-matrix adhesion on the linear viscoelastic creep behavior of ‘as received’ and ‘surface modified’ carbon fibers (AR-CF and SM-CF, respectively) reinforced polyphenylene sulfide (PPS) composite materials was investigated. Short-term tensile creep tests were performed on ±45°

  1. The influence of fiber-matrix adhesion on the linear viscoelastic creep behavior of CF/PPS composites

    NARCIS (Netherlands)

    Motta Dias, M.H.; Jansen, K.M.B.; Luinge, H.; Nayak, K.; Bersee, H.E.N.

    2014-01-01

    The influence of fiber-matrix adhesion on the linear viscoelastic creep behavior of as received and surface modified carbon fiber (AR-CF and SM-CF, respectively) reinforced polyphenylene sulfide (PPS) composite materials was investigated. Short-term tensile creep tests were performed on ±45°

  2. Effect of fiber-matrix adhesion on the creep behavior of CF/PPS composites: temperature and physical aging characterization

    NARCIS (Netherlands)

    Motta Dias, M.H.; Jansen, K.M.B.; Luinge, J.W.; Bersee, H.E.N.; Benedictus, R.

    2016-01-01

    The influence of fiber-matrix adhesion on the linear viscoelastic creep behavior of ‘as received’ and ‘surface modified’ carbon fibers (AR-CF and SM-CF, respectively) reinforced polyphenylene sulfide (PPS) composite materials was investigated. Short-term tensile creep tests were performed on ±45° sp

  3. The influence of fiber-matrix adhesion on the linear viscoelastic creep behavior of CF/PPS composites

    NARCIS (Netherlands)

    Motta Dias, M.H.; Jansen, K.M.B.; Luinge, H.; Nayak, K.; Bersee, H.E.N.

    2014-01-01

    The influence of fiber-matrix adhesion on the linear viscoelastic creep behavior of as received and surface modified carbon fiber (AR-CF and SM-CF, respectively) reinforced polyphenylene sulfide (PPS) composite materials was investigated. Short-term tensile creep tests were performed on ±45° specime

  4. Creep Behavior of Lead-Free Sn-Ag-Cu + Ni-Ge Solder Alloys

    Science.gov (United States)

    Hidaka, N.; Watanabe, H.; Yoshiba, M.

    2009-05-01

    We developed a new lead-free solder alloy, an Sn-Ag-Cu base to which a small amount of Ni and Ge is added, to improve the mechanical properties of solder alloys. We examined creep deformation in bulk and through-hole (TH) form for two lead-free solder alloys, Sn-3.5Ag-0.5Cu-Ni-Ge and Sn-3.0Ag-0.5Cu, at elevated temperatures, finding that the creep rupture life of the Sn-3.5Ag-0.5Cu-Ni-Ge solder alloy was over three times better than that of the Sn-3.0Ag-0.5Cu solder at 398 K. Adding Ni to the solder appears to make microstructural development finer and more uniform. The Ni added to the solder readily combined with Cu to form stable intermetallic compounds of (Cu, Ni)6Sn5 capable of improving the creep behavior of solder alloys. Moreover, microstructural characterization based on transmission electron microscopy analyses observing creep behavior in detail showed that such particles in the Sn-3.5Ag-0.5Cu-Ni-Ge solder alloy prevent dislocation and movement.

  5. Effect of matrix cracking on the time delayed buckling of viscoelastic laminated circular cylindrical shells

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The effect of matrix cracking on the bifurcation creep buckling of viscoelastic laminated circular cylindrical shells is investigated.The viscoelastic behavior of laminas is modeled by Schapery’s integral constitutive equation with growing matrix cracks.The values of damage variables are correlated to non-dimensional density of matrix cracks relying on the formulas from mesomechanics approach,and the evolution equation predicting the growth rate of density of matrix cracks is assumed to follow a power type relation with transverse tensile stress.The governing equations for prebuckling creep deformation and bifurcation buckling of laminated circular cylindrical shells under axial compression are obtained on the basis of the Donnell type shallow shell theory and Kármán-Donnell geometrically nonlinear relationship.Corresponding solution strategy is constructed by integrating finite-difference technique,trigonometric series expansion method and Taylor’s numerical recursive scheme for convolution integration.The bifurcation creep buckling of symmetrically laminated glass-epoxy circular cylindrical shells with matrix creep cracking coupled are examined for various geometrical parameters and parameters of damage evolution as well as boundary conditions.The numerical results show that matrix creep cracking remarkably shortens the critic time of bifurcation buckling and reduces the durable critic loads,and its effects become weak and finally vanish with the increase of the ratio of radius to thickness in the case of short laminated circular cylindrical shells,also the influence of the matrix creep cracking is mainly dependent on the boundary conditions at two ends for moderately long circular cylindrical shells.

  6. Prediction and Monitoring Systems of Creep-Fracture Behavior of 9Cr-1Mo Steels for Teactor Pressure Vessels

    Energy Technology Data Exchange (ETDEWEB)

    Potirniche, Gabriel [Univ. of Idaho, Moscow, ID (United States); Barlow, Fred D. [Univ. of Idaho, Moscow, ID (United States); Charit, Indrajit [Univ. of Idaho, Moscow, ID (United States); Rink, Karl [Univ. of Idaho, Moscow, ID (United States)

    2013-11-26

    A recent workshop on next-generation nuclear plant (NGNP) topics underscored the need for research studies on the creep fracture behavior of two materials under consideration for reactor pressure vessel (RPV) applications: 9Cr-1Mo and SA-5XX steels. This research project will provide a fundamental understanding of creep fracture behavior of modified 9Cr-1Mo steel welds for through modeling and experimentation and will recommend a design for an RPV structural health monitoring system. Following are the specific objectives of this research project: Characterize metallurgical degradation in welded modified 9Cr-1Mo steel resulting from aging processes and creep service conditions; Perform creep tests and characterize the mechanisms of creep fracture process; Quantify how the microstructure degradation controls the creep strength of welded steel specimens; Perform finite element (FE) simulations using polycrystal plasticity to understand how grain texture affects the creep fracture properties of welds; Develop a microstructure-based creep fracture model to estimate RPVs service life; Manufacture small, prototypic, cylindrical pressure vessels, subject them to degradation by aging, and measure their leak rates; Simulate damage evolution in creep specimens by FE analyses; Develop a model that correlates gas leak rates from welded pressure vessels with the amount of microstructural damage; Perform large-scale FE simulations with a realistic microstructure to evaluate RPV performance at elevated temperatures and creep strength; Develop a fracture model for the structural integrity of RPVs subjected to creep loads; and Develop a plan for a non-destructive structural health monitoring technique and damage detection device for RPVs.

  7. Simultaneous consolidation and creep

    DEFF Research Database (Denmark)

    Krogsbøll, Anette

    1997-01-01

    Materials that exhibit creep under constant effective stress typically also show rate dependent behavior. The creep deformations and the rate sensitive behavior is very important when engineering and geological problems with large time scales are considered. When stress induced compaction...... (consolidation) is retarded by slow drainage of excess pore pressure it is expected that consolidation and creep occur simultaneously. A constitutive model adressing the problems of rate sensitive behavior and simultaneous consolidation and creep is presented....

  8. A Comparison of Tension and Compression Creep in a Polymeric Composite and the Effects of Physical Aging on Creep Behavior

    Science.gov (United States)

    Gates, Thomas S.; Veazie, David R.; Brinson, L. Catherine

    1996-01-01

    Experimental and analytical methods were used to investigate the similarities and differences of the effects of physical aging on creep compliance of IM7/K3B composite loaded in tension and compression. Two matrix dominated loading modes, shear and transverse, were investigated for two load cases, tension and compression. The tests, run over a range of sub-glass transition temperatures, provided material constants, material master curves and aging related parameters. Comparing results from the short-term data indicated that although trends in the data with respect to aging time and aging temperature are similar, differences exist due to load direction and mode. The analytical model used for predicting long-term behavior using short-term data as input worked equally as well for the tension or compression loaded cases. Comparison of the loading modes indicated that the predictive model provided more accurate long term predictions for the shear mode as compared to the transverse mode. Parametric studies showed the usefulness of the predictive model as a tool for investigating long-term performance and compliance acceleration due to temperature.

  9. Effect of Microstructure on Creep Crack Growth Behavior of a Near- α Titanium Alloy IMI-834

    Science.gov (United States)

    Satyanarayana, D. V. V.; Omprakash, C. M.; Sridhar, T.; Kumar, Vikas

    2009-01-01

    In the present study, the effect of microstructure ( i.e., α + β and transformed β) on creep crack growth (CCG) behavior of a near-alpha (IMI 834) titanium alloy has been explored at temperatures 550 °C and 600 °C. For characterizing the CCG behavior of the alloy, both stress intensity factor ( K) and energy integral parameter ( C t ) were used in the present investigation. The use of stress intensity factor ( K) as crack-tip parameter is not appropriate in the present study as no unique correlation between crack growth rate and K could be obtained from the observed trend due to transients in the creep crack rate data. On the other hand, C t parameter for both microstructural conditions consolidates CCG data into a single trend. The alloy with fully transformed β microstructure exhibits better CCG resistance as compared to bimodal ( α + β) microstructure. This is consistent with the fact that the transformed β structure offers superior creep resistance as compared to α + β microstructure. Microstructural examination has revealed that CCG for both microstructural conditions is accompanied by formation of damage zone in the form of numerous environmental-assisted secondary surface cracks (perpendicular to the stress axis) ahead of the main crack tip. For α + β microstructure of the alloy, the surface creep cracks were formed by growth and coalescence of microcracks nucleated by fracture of primary α particles. While in the interior of the specimens, CCG occurred by growth and coalescence of microvoids nucleated at primary α/transformed β (matrix) interfaces. For β microstructure of the alloy, while the surface creep cracks formed by growth and coalescence of microvoids nucleated at titanium enriched surface oxide particles, in the interior CCG occurred by nucleation of intergranular cavities.

  10. Creep Behavior in Interlaminar Shear of a SiC/SiC Ceramic Composite with a Self-healing Matrix

    Science.gov (United States)

    Ruggles-Wrenn, M. B.; Pope, M. T.

    2014-02-01

    Creep behavior in interlaminar shear of a non-oxide ceramic composite with a multilayered matrix was investigated at 1,200 °C in laboratory air and in steam environment. The composite was produced via chemical vapor infiltration (CVI). The composite had an oxidation inhibited matrix, which consisted of alternating layers of silicon carbide and boron carbide and was reinforced with laminated Hi-Nicalon™ fibers woven in a five-harness-satin weave. Fiber preforms had pyrolytic carbon fiber coating with boron carbide overlay applied. The interlaminar shear properties were measured. The creep behavior was examined for interlaminar shear stresses in the 16-22 MPa range. Primary and secondary creep regimes were observed in all tests conducted in air and in steam. In air and in steam, creep run-out defined as 100 h at creep stress was achieved at 16 MPa. Larger creep strains were accumulated in steam. However, creep strain rates and creep lifetimes were only moderately affected by the presence of steam. The retained properties of all specimens that achieved run-out were characterized. Composite microstructure, as well as damage and failure mechanisms were investigated.

  11. Measurement of buckling load for metallic plate columns in severe accident conditions

    Energy Technology Data Exchange (ETDEWEB)

    Jo, Byeongnam, E-mail: jo@vis.t.u-tokyo.ac.jp; Sagawa, Wataru, E-mail: sagawa@vis.t.u-tokyo.ac.jp; Okamoto, Koji, E-mail: okamoto@n.t.u-tokyo.ac.jp

    2014-07-01

    Highlights: • Buckling load was experimentally measured in a wide range of temperature up to 1200 °C. • Two different test methods for measuring buckling failure load were suggested and compared. • Creep buckling under compressive load was performed to explain results of buckling tests. • Reduced buckling load was explained by effects of creep buckling, geometrical imperfection, and thermal stress. • Buckling processes were visualized by a high speed camera. - Abstract: In severe accidents, a reactor pressure vessel, its components, and piping have to be under extremely high temperature and high pressure conditions, which results in failure modes like rupture by internal pressure, buckling, creep, and their combinations. In this study, buckling (failure) load was experimentally measured for metallic columns under the compressive force from room temperature up to 1200 °C. A stainless steel was chosen to be a test material to measure the buckling load. Two different test methods were employed to explore the effect of thermal history of the material on the buckling load. Particularly, the effect of creep under a compressive load was considered as a reason for the reduced buckling load at high temperatures. Additionally, finite element simulations were also conducted to predict buckling load for both an ideal column and a column with geometrical imperfection as well. Moreover, buckling process was visualized using a high speed camera to understand buckling processes.

  12. Indentation creep behavior of cold sprayed aluminum amorphous/nano-crystalline coatings

    Energy Technology Data Exchange (ETDEWEB)

    Babu, P. Suresh [International Advanced Research Centre for Powder Metallurgy and New Materials (ARCI), Balapur, Hyderabad 500005, Andhra Pradesh (India); Nanomechanics and Nanotribology Laboratory, Department of Mechanical and Materials Engineering, Florida International University, Miami, FL 33174 (United States); Jha, R.; Guzman, M. [Nanomechanics and Nanotribology Laboratory, Department of Mechanical and Materials Engineering, Florida International University, Miami, FL 33174 (United States); Sundararajan, G. [International Advanced Research Centre for Powder Metallurgy and New Materials (ARCI), Balapur, Hyderabad 500005, Andhra Pradesh (India); Agarwal, Arvind, E-mail: agarwala@fiu.edu [Nanomechanics and Nanotribology Laboratory, Department of Mechanical and Materials Engineering, Florida International University, Miami, FL 33174 (United States)

    2016-03-21

    In this study, we report room temperature creep properties of cold sprayed aluminum amorphous/nanocrystalline coating using nanoindentation technique. Creep experiments were also performed on heat treated coatings to study the structural stability and its influence on the creep behavior. The peak load and holding time were varied from 1000 to 4000 µN and 0 to 240 s respectively. Stress exponent value (n) vary from 5.6 to 2.3 in as-sprayed (AS) coatings and 7.2–4.8 in heat treated (HT) coatings at peak load of 1000–4000 µN at 240 s hold time. Higher stress exponent value indicates heat treated coatings have more resistance to creep deformation than as-sprayed coatings. Relaxed, partially crystallized structure with less porosity, and stronger inter-splat boundaries restrict the deformation in heat treated coatings as compared to greater free volume generation in amorphous as-sprayed coatings. The computed activation volume of heat treated coatings is twice of as-sprayed coatings indicating greater number of atom participation in shear band formation in heat treated coatings. The proposed mechanism was found to be consistent with the stress exponent values.

  13. Geometry and Material Constraint Effects on Creep Crack Growth Behavior in Welded Joints

    Science.gov (United States)

    Li, Y.; Wang, G. Z.; Xuan, F. Z.; Tu, S. T.

    2017-02-01

    In this work, the geometry and material constraint effects on creep crack growth (CCG) and behavior in welded joints were investigated. The CCG paths and rates of two kinds of specimen geometry (C(T) and M(T)) with initial cracks located at soft HAZ (heat-affected zone with lower creep strength) and different material mismatches were simulated. The effect of constraint on creep crack initiation (CCI) time was discussed. The results show that there exists interaction between geometry and material constraints in terms of their effects on CCG rate and CCI time of welded joints. Under the condition of low geometry constraint, the effect of material constraint on CCG rate and CCI time becomes more obvious. Higher material constraint can promote CCG due to the formation of higher stress triaxiality around crack tip. Higher geometry constraint can increase CCG rate and reduce CCI time of welded joints. Both geometry and material constraints should be considered in creep life assessment and design for high-temperature welded components.

  14. Buckling Behavior of Long Anisotropic Plates Subjected to Elastically Restrained Thermal Expansion and Contraction

    Science.gov (United States)

    Nemeth, Michael P.

    2004-01-01

    An approach for synthesizing buckling results for thin balanced and unbalanced symmetric laminates that are subjected to uniform heating or cooling and elastically restrained against thermal expansion or contraction is presented. This approach uses a nondimensional analysis for infinitely long, flexural anisotropic plates that are subjected to combined mechanical loads. In addition, stiffness-weighted laminate thermal-expansion parameters and compliance coefficients are derived that are used to determine critical temperatures in terms of physically intuitive mechanical-buckling coefficients. Many results are presented for some common laminates that are intended to facilitate a structural designer s transition to the use of the generic buckling design curves. Several curves that illustrate the fundamental parameters used in the analysis are presented, for nine contemporary material systems, that provide physical insight into the buckling response in addition to providing useful design data. Examples are presented that demonstrate the use of the generic design curves.

  15. The effect of multiaxial stress state on creep behavior and fracture mechanism of P92 steel

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Yuan; Xu, Hong, E-mail: xuhong@ncepu.edu.cn; Ni, Yongzhong; Lan, Xiang; Li, Hongyuan

    2015-06-11

    The creep experiments on plain and double U-typed notched specimens were conducted on P92 steel at 650 °C. The notch strengthening effect was found in the notched specimens. Fracture appearance observed by scanning electron microscopy revealed that dimpled fracture for relatively blunt notched specimen, and dimpled fracture doubled with intergranular brittle fracture for relatively sharp notched specimen, which meant that fracture mechanism of P92 steel altered due to the presence of the notch. Meanwhile, based on Norton–Bailey and Kachanov–Robotnov constitutive models, a modified model was proposed. Finite element simulations were carried out to investigate the effect of multiaxial stress state on the creep behavior, fracture mechanism and damage evolvement of P92 steel. The simulation results agreed well with the fracture behaviors observed experimentally.

  16. NUMERICAL STUDY OF THE NOTCH EFFECT ON THE CREEP BEHAVIOR AND LIFE OF NICKEL-BASE SINGLE CRYSTAL SUPERALLOYS

    Institute of Scientific and Technical Information of China (English)

    Q.M. Yu; Z.F. Yue

    2004-01-01

    Numerical calculations of creep damage development and life behavior of circular notched specimens of nickel-base single crystal had been performed. The creep stress distributions depend on the specimen geometry. For a small notch radius, von Mises stress has an especial distribution. The damage distribution is greatly influenced by the notch depth, notch radius as well as notch type. The creep crack initiation place is different for each notched specimen. The characteristics of notch strengthening and notch weakening depend on the notch radius and notch type. For the same notch type,the creep rupture lives decrease with the decreasing of notch radius. A creep life model has been presented for the multiaxial stress states based on the crystallographic slip system theory.

  17. Creep Behavior of Glass/Ceramic Sealant and its Effect on Long-term Performance of Solid Oxide Fuel Cells

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Wenning N.; Sun, Xin; Koeppel, Brian J.; Stephens, Elizabeth V.; Khaleel, Mohammad A.

    2009-10-14

    The creep behavior of glass or glass-ceramic sealant materials used in solid oxide fuel cells (SOFCs) becomes relevant under SOFC operating temperatures. In this paper, the creep of glass-ceramic sealants was experimentally examined, and a standard linear solid model was applied to capture the creep behavior of glass ceramic sealant materials developed for planar SOFCs at high temperatures. The parameters of this model were determined based on the creep test results. Furthermore, the creep model was incorporated into finite-element software programs SOFC-MP and Mentat-FC developed at Pacific Northwest National Laboratory for multi-physics simulation of SOFCs. The effect of creep of glass ceramic sealant materials on the long-term performance of SOFC stacks was investigated by studying the stability of the flow channels and the stress redistribution in the glass seal and on the various interfaces of the glass seal with other layers. Finite element analyses were performed to quantify the stresses in various parts. The stresses in glass seals were released because of creep behavior during operations.

  18. Growth Kinetics of Laves Phase and Its Effect on Creep Rupture Behavior in 9Cr Heat Resistant Steel

    Institute of Scientific and Technical Information of China (English)

    Zhi-xin XIA; Chuan-yang WANG; Chen LEI; Yun-ting LAI; Yan-fen ZHAO; Lu ZHANG

    2016-01-01

    The effects of Laves phase formation and growth on creep rupture behaviors of P92 steel at 883 K were studied.The microstructural evolution was characterized using scanning electron microscopy and transmission elec-tron microscopy.Kinetic modeling was carried out using the software DICTRA.The results indicated Fe2 (W,Mo) Laves phase has formed during creep with 200 MPa applied stress at 883 K for 243 h.The experimental results showed a good agreement with thermodynamic calculations.The plastic deformation of laths is the main reason of creep rupture under the applied stress beyond 160 MPa,whereas,creep voids initiated by coarser Laves phase play an effective role in creep rupture under the applied stress lower than 160 MPa.Laves phase particles with the mean size of 243 nm lead to the change of creep rupture feature.Microstructures at the vicinity of fracture surface,the gage portion and the threaded ends of creep rupture specimens were also observed,indicating that creep tensile stress enhances the coarsening of Laves phase.

  19. Creep behavior of reduced activation ferritic/martensitic steels irradiated at 573 and 773 K up to 5 dpa

    Energy Technology Data Exchange (ETDEWEB)

    Ando, M. [Fusion Structural Materials Development Group, Directorates of Fusion Energy Technology, Fusion Research and Development Directorate, Japan Atomic Energy Agency (JAEA) (Japan)]. E-mail: ando.masami@jaea.go.jp; Li, M. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Tanigawa, H. [Fusion Structural Materials Development Group, Directorates of Fusion Energy Technology, Fusion Research and Development Directorate, Japan Atomic Energy Agency (JAEA) (Japan); Grossbeck, M.L. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); University of Tennessee, Knoxville, TN 37996-2300 (United States); Kim, S. [Institute of Advanced Energy, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan); Sawai, T. [Fusion Structural Materials Development Group, Directorates of Fusion Energy Technology, Fusion Research and Development Directorate, Japan Atomic Energy Agency (JAEA) (Japan); Shiba, K. [Fusion Structural Materials Development Group, Directorates of Fusion Energy Technology, Fusion Research and Development Directorate, Japan Atomic Energy Agency (JAEA) (Japan); Kohno, Y. [Muroran Institute of Technology, Muroran, Hokkaido 050-8585 (Japan); Kohyama, A. [Institute of Advanced Energy, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan)

    2007-08-01

    The irradiation creep behavior of F82H and several variants of JLF-1 steel has been measured at 573 and 773 K up to 5 dpa using helium-pressurized creep tubes irradiated in HFIR. These tubes were pressurized with helium to hoop stress levels of 0-400 MPa at the irradiation temperature. The results for F82H and JLF-1 with a 400 MPa hoop stress showed small creep strains (<0.25%) after irradiation at 573 K. The irradiation creep strain at 573 K in these steels is linearly dependent on the applied stress at stress levels below 250 MPa. However, at higher hoop stress levels, the creep strain becomes nonlinear. At 773 K, the irradiation creep strain of F82H is linearly dependent on the applied stress level below 100 MPa. At higher stress levels, the creep strain increased strongly. The creep compliance coefficients for F82H and JLF-1 are consistent with the values obtained for other steels. These data contribute to the materials database for ITER test blanket design work.

  20. Creep-Fatigue Behavior of Alloy 617 at 850 and 950°C, Revision 2

    Energy Technology Data Exchange (ETDEWEB)

    Carroll, L. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Carroll, M. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-05-01

    Alloy 617 is the leading candidate material for an Intermediate Heat Exchanger (IHX) of the Very High Temperature Reactor (VHTR). To evaluate the behavior of this material in the expected service conditions, strain-controlled cyclic tests including hold times up to 9000 s at maximum tensile strain were conducted at 850 and 950 degrees C. At both temperatures, the fatigue resistance decreased when a hold time was added at peak tensile strain. The magnitude of this effect depended on the specific mechanisms and whether they resulted in a change in fracture mode from transgranular in pure fatigue to intergranular in creep-fatigue for a particular temperature and strain range combination. Increases in the tensile hold duration beyond an initial value were not detrimental to the creep-fatigue resistance at 950 degrees C but did continue to degrade the lifetimes at 850 degrees C.

  1. Experimental study on the buckling and post-buckling behavior of thin-walled cylindrical shells with varying thickness under hydrostatic pressure

    OpenAIRE

    FAKHIM, Y. G.; SHOWKATI, H.; K Abedi

    2009-01-01

    p. 2511-2522 The application of thin-walled cylindrical shells, as the essential structural members, has been known for engineers and functional duty of them is basic necessaries of modern industries. These structures are prone to fail by buckling under external pressure which could be happened during discharging or wind load. Although the buckling capacity of the shells depends principally on two geometric ratios of "length to radius" (L/R) and "radius to thickness" (R/t), but...

  2. Creep deformation and rupture behavior of CLAM steel at 823 K and 873 K

    Science.gov (United States)

    Zhong, Boyu; Huang, Bo; Li, Chunjing; Liu, Shaojun; Xu, Gang; Zhao, Yanyun; Huang, Qunying

    2014-12-01

    China Low Activation Martensitic (CLAM) steel is selected as the candidate structural material in Fusion Design Study (FDS) series fusion reactor conceptual designs. The creep property of CLAM steel has been studied in this paper. Creep tests have been carried out at 823 K and 873 K over a stress range of 150-230 MPa. The creep curves showed three creep regimes, primary creep, steady-state creep and tertiary creep. The relationship between minimum creep rate (ε˙min) and the applied stress (σ) could be described by Norton power law, and the stress exponent n was decreased with the increase of the creep temperature. The creep mechanism was analyzed with the fractographes of the rupture specimens which were examined by scanning electron microscopy (SEM). The coarsening of precipitates observed with transmission electron microscope (TEM) indicated the microstructural degradation after creep test.

  3. Creep behavior of plasma sprayed NiCr and NiCrAl coating-based systems

    Institute of Scientific and Technical Information of China (English)

    Xiancheng ZHANG; Changjun LIU; Fuzhen XUAN; Zhengdong WANG; Shan-Tung TU

    2011-01-01

    The creep behavior of the plasma sprayed NiCr and NiCrAl coating/Nickel alloy 690substrate systems at 1033 K was investigated. Results showed that there was almost no difference in the creep lives between the NiCr and NiCrAl coated specimens at a given stress level, since the contents of Cr used in the NiCr and NiCrAl powders are almost same. The relationship between the minimum creep rate and the applied stress followed the well-known Norton's power law, εmin=Aσn, with the values of A=2.66× 10-16 Mpa-n.h-1 and n=6.48. The relation between the applied stress and time to rupture of the coated specimens can be estimated by using Larson-Miller equation. The θ projection method can be used to accurately characterize the creep behavior of the coated specimens.

  4. Influence of loading path and precipitates on indentation creep behavior of wrought Mg–6 wt% Al–1 wt% Zn magnesium alloy

    Energy Technology Data Exchange (ETDEWEB)

    Nautiyal, Pranjal [Discipline of Mechanical Engineering, Indian Institute of Information Technology, Design & Manufacturing, Jabalpur, Madhya Pradesh 482005 (India); Department of Applied Mechanics, Indian Institute of Technology, Delhi 110016 (India); Jain, Jayant [Department of Applied Mechanics, Indian Institute of Technology, Delhi 110016 (India); Agarwal, Arvind, E-mail: agarwala@fiu.edu [Department of Mechanical and Materials Engineering, Florida International University, Miami, FL 33174 (United States)

    2016-01-05

    This study reports the effect of loading path and precipitates on indentation induced creep behavior of AZ61 magnesium alloy. Indentation creep tests were performed on solution-treated and peak-aged extruded AZ61 magnesium alloy, and Atomic Force Microscopy (AFM) investigations were carried out to study deformation mechanisms. Twinning is the dominant creep mechanism for indentation along the extrusion direction (ED) in solution-treated alloy. A combination of slip and twinning appears to be the prominent mechanisms for indentation creep perpendicular to ED. Creep flow is arrested for indentation perpendicular to ED, due to slip–twin interactions. Influence of precipitates on creep deformation was also studied. Aged specimen exhibited higher creep resistance than solution-treated specimen. Unlike solution-treated specimens, twinning was not observed in aged alloy. Creep in aged specimen was attributed to slip.

  5. Influence of dispersoids on the creep behavior of dispersion strengthened aluminum materials

    Directory of Open Access Journals (Sweden)

    Carreño, F.

    1997-10-01

    Full Text Available The creep behavior of a rapidly solidified Al-6.5%Fe-0.6%V-1.3%Si dispersion strengthened material containing 16 volume % of dispersoids has been studied by means of tensile tests at high temperatures from 483 to 821 K. The imposed strain rates ranged from 2.5∙10-6 to 10-2s-1. The microstructure was very fine, consisting of submicron grains and small hard round-shaped dispersoids of about 54 nm. The creep behavior was characterized by high apparent stress exponents and high activation energies that are not accurately predicted by models from the literature. Therefore, a creep equation is developed to describe the creep behavior of the studied aluminum dispersion strengthened material and other materials with similar microstructures. The proposed equation is a generalization of conventional slip creep equations without the use of a threshold stress.

    Se estudió el comportamiento en fluencia del material solidificado rápidamente Al-6,5%Fe-0,6%V-1,3%Si, reforzado por dispersión que contenía una fracción de volumen de dispersoides de 16 %, mediante ensayos de tracción a altas temperaturas desde 483 a 821 K. Las velocidades de deformación impuestas variaron desde 2,5∙10-6 to 10-2s-1. La microestructura, que era muy fina, estaba formada por granos submicrométricos y pequeños dispersoides redondeados y duros de unos 54 nm. El comportamiento en fluencia se caracterizó por altos exponentes de la tensión aparente y altas energías de activación aparentes que no se predicen con exactitud por modelos de la literatura. Por ello, se ha desarrollado una ecuación de fluencia que describe el comportamiento del material de base aluminio reforzado por dispersión y de otros materiales de microestructura similar. La ecuación propuesta es una generalización de ecuaciones de fluencia convencionales por movimiento de dislocaciones y no emplea una tensión umbral.

  6. STUDY ON THE EFFECTS OF BREAKAGE OF SINGLE FIBER ON CREEP BEHAVIOR OF FIBER REINFORCED COMPOSITES

    Institute of Scientific and Technical Information of China (English)

    X.J. Shao; Y.P. Jiang; Z. F. Yue

    2004-01-01

    A 3-D micro cell model with multi-fibers has been presented to study the effects of breakage of single fiber on the whole creep behavior of fiber reinforced composites by finite element method (FEM). Before the fiber breakage, the stresses of all fibers are identical. With the creep time increasing, stress in fiber increases but stress in matrix decreases. It is assumed that the fiber breakage occurs when the stress in fiber reaches a critical value. The stress redistribution resulted from the breakage of fiber has been obtained. The influence on the axial stress of the broken fiber is local. The stress in the all fiber sections is not uniform. There is a local stress concentration in the matrix. And this stress concentration in the matrix is more and more serious with the creep deformation. The stress transference of the loading due to the fiber breakage has been studies numerically. It is found that the fibers near to the broken fiber will take over more loading.

  7. Low temperature creep plasticity

    Directory of Open Access Journals (Sweden)

    Michael E. Kassner

    2014-07-01

    Full Text Available The creep behavior of crystalline materials at low temperatures (T < 0.3Tm is discussed. In particular, the phenomenological relationships that describe primary creep are reviewed and analyzed. A discussion of the activation energy for creep at T < 0.3Tm is discussed in terms of the context of higher temperature activation energy. The basic mechanism(s of low temperature creep plasticity are discussed, as well.

  8. Investigation on creep behavior of geo-materials with suction control technique

    Directory of Open Access Journals (Sweden)

    Nishimura Tomoyoshi

    2016-01-01

    Full Text Available The compacted bentonite which has typical couple problem associated to thermal - hydration - mechanical – chemical (THMC consist of one component of engineered barrier. Recently, the couple THMC formulation modelling suggested by some researchers can be predicted basically phenomena for engineered barrier that approach to correct evaluate satisfied facilities. The compacted bentonite is essentially unsaturated condition, some behaviors for bentonite has similar or close with generally expansive unsaturated soils. Therefore, hydrations have given significant influence on deformation of compacted bentonite such as swelling. There are many researches for swelling behavior of compacted bentonite within soaking. Extended theoretical or experimental investigations for unsaturated soil mechanics are possible to describe the strength-deformation behavior of compacted bentonite with suction controlling principle. A new method of determining the failure phase such as great axis deformation and destructions like strip of surface in the laboratory is described and the creep behavior of compacted bentonite is considered under maintain of high relative humidity environment. The creep deformation measured using improved cyclic relative humidity control apparatus in terms of specific suction control technique.

  9. Nonlocal and surface effects on the buckling behavior of functionally graded nanoplates: An isogeometric analysis

    Science.gov (United States)

    Ansari, R.; Norouzzadeh, A.

    2016-10-01

    The size-dependent static buckling responses of circular, elliptical and skew nanoplates made of functionally graded materials (FGMs) are investigated in this article based on an isogeometric model. The Eringen nonlocal continuum theory is implemented to capture nonlocal effects. According to the Gurtin-Murdoch surface elasticity theory, surface energy influences are also taken into account by the consideration of two thin surface layers at the top and bottom of nanoplate. The material properties vary in the thickness direction and are evaluated using the Mori-Tanaka homogenization scheme. The governing equations of buckled nanoplate are achieved by the minimum total potential energy principle. To perform the isogeometric analysis as a solution methodology, a novel matrix-vector form of formulation is presented. Numerical examples are given to study the effects of surface stress as well as other important parameters on the critical buckling loads of functionally graded nanoplates. It is found that the buckling configuration of nanoplates at small scales is significantly affected by the surface free energy.

  10. Creep rupture strength and creep behavior of low-activation martensitic OPTIFER alloys. Final report; Das Zeitstandfestigkeits- und Kriechverhalten der niedrigaktivierenden martensitischen OPTIFER-Legierungen. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Schirra, M.; Falkenstein, A.; Heger, S.; Lapena, J. [ITN-CIEMAT, Madrid (Spain). Programa de Materiales

    2001-07-01

    The creep rupture strength and creep experiments performed on low-activation OPTIFER alloys in the temperature range of 450-700 C shall be summarized in the present report. Together with the reference alloy of the type 9.5Cr1W-Mn-V-Ta, W-free variants (+Ge) with a more favorable activation and decay behavior shall be studied. Their smaller strength values are compensated by far better toughness characteristics. Of each development line, several batches of slightly varying chemical composition have been investigated over service lives of up to 40,000 h. Apart from the impact of a reference thermal treatment at a hardening temperature of 1075 C and an annealing temperature of 750 C, the influence of reduced hardening temperatures (up to 950 C) has been determined. A long-term use at increased temperatures (max. 550 C-20,000 h) produces an aging effect with strength being decreased in the annealed state. To determine this aging effect quantitatively, creep rupture experiments have been performed using specimens that were subjected to variable types of T/t annealing (550 -650 C, 330-5000 h). Based on all test results, minimum values for the 1% time-strain limit and creep rupture in the T range of 400-600 C can be given as design curves for 20,000 h. The minimum creep rates obtained from the creep curves recorded as a function of the experimental stress yield the stress exponent n (n=Norton) for the individual test temperatures. Creep behavior as a function of the test temperature yields the values for the effective activation energy of creeping Q{sub K}. The influence of a preceding temperature transient up to 800 C ({<=}Ac{sub 1b}) or 840 C (>Ac{sub 1b}) with subsequent creep rupture tests at 500 C and 550 C, respectively, shall be described. The results obtained for the OPTIFER alloys shall be compared with the results achieved for the Japanese 2% W-containing F82H-mod. alloy. (orig.) [German] Die Zeitstandfestigkeits- und Kriechversuche an den niedrigaktivierenden

  11. Creep Behavior of a Sn-Ag-Bi Pb-Free Solder

    Directory of Open Access Journals (Sweden)

    Alice Kilgo

    2012-11-01

    Full Text Available Compression creep tests were performed on the ternary 91.84Sn-3.33Ag-4.83Bi (wt.%, abbreviated Sn-Ag-Bi Pb-free alloy. The test temperatures were: −25 °C, 25 °C, 75 °C, 125 °C, and 160 °C (± 0.5 °C. Four loads were used at the two lowest temperatures and five at the higher temperatures. The specimens were tested in the as-fabricated condition or after having been subjected to one of two air aging conditions: 24 hours at either 125 °C or 150 °C. The strain-time curves exhibited frequent occurrences of negative creep and small-scale fluctuations, particularly at the slower strain rates, that were indicative of dynamic recrystallization (DRX activity. The source of tertiary creep behavior at faster strain rates was likely to also be DRX rather than a damage accumulation mechanism. Overall, the strain-time curves did not display a consistent trend that could be directly attributed to the aging condition. The sinh law equation satisfactorily represented the minimum strain rate as a function of stress and temperature so as to investigate the deformation rate kinetics: dε/dtmin = Asinhn (ασ exp (−ΔH/RT. The values of α, n, and  ΔH were in the following ranges (±95% confidence interval: α, 0.010–0.015 (±0.005 1/MPa; n, 2.2–3.1 (±0.5; and ΔH, 54–66 (±8 kJ/mol. The rate kinetics analysis indicated that short-circuit diffusion was a contributing mechanism to dislocation motion during creep. The rate kinetics analysis also determined that a minimum creep rate trend could not be developed between the as-fabricated versus aged conditions. This study showed that the elevated temperature aging treatments introduced multiple changes to the Sn-Ag-Bi microstructure that did not result in a simple loss (“softening” of its mechanical strength.

  12. Improved tensile and buckling behavior of defected carbon nanotubes utilizing boron nitride coating – A molecular dynamic study

    Energy Technology Data Exchange (ETDEWEB)

    Badjian, H.; Setoodeh, A.R., E-mail: setoodeh@sutech.ac.ir

    2017-02-15

    Synthesizing inorganic nanostructures such as boron nitride nanotubes (BNNTs) have led to immense studies due to their many interesting functional features such as piezoelectricity, high temperature resistance to oxygen, electrical insulation, high thermal conductivity and very long lengths as physical features. In order to utilize the superior properties of pristine and defected carbon nanotubes (CNTs), a hybrid nanotube is proposed in this study by forming BNNTs surface coating on the CNTs. The benefits of such coating on the tensile and buckling behavior of single-walled CNTs (SWCNTs) are illustrated through molecular dynamics (MD) simulations of the resulted nanostructures during the deformation. The AIREBO and Tersoff-Brenner potentials are employed to model the interatomic forces between the carbon and boron nitride atoms, respectively. The effects of chiral indices, aspect ratio, presence of mono-vacancy defects and coating dimension on coated/non-coated CNTs are examined. It is demonstrated that the coated defective CNTs exhibit remarkably enhanced ultimate strength, buckling load capacity and Young's modulus. The proposed coating not only enhances the mechanical properties of the resulted nanostructure, but also conceals it from few external factors impacting the behavior of the CNT such as humidity and high temperature.

  13. Improved tensile and buckling behavior of defected carbon nanotubes utilizing boron nitride coating - A molecular dynamic study

    Science.gov (United States)

    Badjian, H.; Setoodeh, A. R.

    2017-02-01

    Synthesizing inorganic nanostructures such as boron nitride nanotubes (BNNTs) have led to immense studies due to their many interesting functional features such as piezoelectricity, high temperature resistance to oxygen, electrical insulation, high thermal conductivity and very long lengths as physical features. In order to utilize the superior properties of pristine and defected carbon nanotubes (CNTs), a hybrid nanotube is proposed in this study by forming BNNTs surface coating on the CNTs. The benefits of such coating on the tensile and buckling behavior of single-walled CNTs (SWCNTs) are illustrated through molecular dynamics (MD) simulations of the resulted nanostructures during the deformation. The AIREBO and Tersoff-Brenner potentials are employed to model the interatomic forces between the carbon and boron nitride atoms, respectively. The effects of chiral indices, aspect ratio, presence of mono-vacancy defects and coating dimension on coated/non-coated CNTs are examined. It is demonstrated that the coated defective CNTs exhibit remarkably enhanced ultimate strength, buckling load capacity and Young's modulus. The proposed coating not only enhances the mechanical properties of the resulted nanostructure, but also conceals it from few external factors impacting the behavior of the CNT such as humidity and high temperature.

  14. CREEP BEHAVIOR OF TI-6AL-4V WITH MARTENSITIC AND EQUIAXED STRUCTURES AT 600°C

    Directory of Open Access Journals (Sweden)

    Luciana Aparecida Narciso da Silva Briguent

    2013-12-01

    Full Text Available Ti-6Al-4V presents important properties as high specific strength, corrosion and creep resistance and metallurgical stability and it has been used in aerospace and aeronautical industries in some applications that requires high temperatures resistance. For these reasons is important understand Ti-6Al-4V deformation at high temperatures. A method of increasing the resistance of a material is heat treatments which can modify its microstructure. Aiming the improvement of Ti-6Al-4V creep resistance it was performed a specific heat treatment in this alloy to obtain a martensitic microstructure. The material was heat-treated at 1,050°C for 30 minutes and cooled in water until room temperature. The aim of this work is to evaluate Ti-6Al-4V creep behavior with equiaxed and martensitic microstructure at 600°C and stress conditions of 125 MPa, 250 MPa e 319 MPa at constant load. The alloy with martensitic structure showed higher creep resistance with a longer time in creep and lower steady-state creep rate.

  15. ELECTRORHEOLOGY AND CREEP-RECOVERY BEHAVIOR OF CONDUCTING POLYTHIOPHENE/POLY(OXYMETHYLENE)-BLEND SUSPENSIONS

    Institute of Scientific and Technical Information of China (English)

    Ozlem Erol; H.Ibrahim Unal; Bekir Sari

    2012-01-01

    Electrorheological properties and creep-recovery behavior of polythiophene/polyoxymethylene-blend having PT(50%)/POM(50%) composition wcrc invcstigatcd.Particle size,conductivity and dielectric values were measured to be 24.77 μm,3.85 × 10-5 S·m-1 and 26.75,respectively.Sedimentation ratio was measured to be 64% at the end of 16 days.The effects of dispersed particle volume fraction,external electric field strength,shear rate,frequency and temperature on ER properties and storage modulus of PT/POM-blend/silicone oil (SO) suspensions were examined.Enhancement were observed in the electric field viscosities of the suspensions and thus they were classified as a smart material.Shear thinning non-Newtonian viscoelastic behavior was determined for PT/POM-blend/SO system.Further,time-dependent deformation was examined by creep-recovery tests and recoverable viscoelastic deformation established.

  16. Vibration and buckling studies of pretensioned structures

    Science.gov (United States)

    Belvin, W. K.

    1982-01-01

    Results of analyses and tests of a simple pretensional structure are presented. Linear finite element analysis correlated well with experimental small amplitude vibration data. The buckling and vibration behavior of a pretensional stayed column was studied in detail. The bifurcation buckling load was also predicted accurately. Postbuckling behavior of the column was unusual and results in a post buckling restoring force of only 1/64 the bifurcation buckling load. Interaction between lateral accelerations and compressive load creates isolated stay slackening at loads above 50 percent of the buckling load. Further research will be required to fully understand their impact on the use of pretensioned structures as large space structures.

  17. CREEP CRACK GROWTH BEHAVIOR OF ALLOY 718 DURING HIGH TEMPERATURE EXPOSURE

    Institute of Scientific and Technical Information of China (English)

    J.X. Dong; M.C. Zhang; Y.P. Zeng; X.S. Xie

    2005-01-01

    Alloy 718 is a precipitation strengthened nickel-based superalloy based on the precipitation ofγ"-Ni3Nb (DO22 structure) and γ-Ni3(Al, Ti) (Ll2 structure) phases. Creep crack growth rate(CCGR) was investigated after high temperature exposure at 593, 650 and 677℃ for 2000h inAlloy 718. In addition to the coalescence of γ'/ γ" and the amount increasing of δ phase, theexistence of a bcc chromium enriched α-Cr phase was observed by SEM, and the weight fraction of α-Cr and other phases were determined by chemical phase analysis methods. The CCGR behavior and regulation have been analyzed by means of strength and structure analysis approaches. The experimental results show higher the exposure temperature and longer the ex posure time, lower the CCGR. This is probably attributed to the interaction of material softening and brittling due to complex structure changes during high temperature exposure. Therefore,despite α-Cr phase formation and amount enhancement were run in this test range. It seems to us a srnall amount of α-Cr will be not harmful for creep crack propagation resistance, which is critical for disk application in aircraft and land-based gas turbine.

  18. The role of proteoglycans in the nanoindentation creep behavior of human dentin.

    Science.gov (United States)

    Bertassoni, Luiz E; Kury, Matheus; Rathsam, Catherine; Little, Christopher B; Swain, Michael V

    2015-03-01

    Attempts to understand the mechanical behavior of dentin and other mineralized tissues have been primarily focused on the role of their more abundant matrix components, such as collagen and hydroxyapatite. The structural mechanisms endowing these biological materials with outstanding load bearing properties, however, remain elusive to date. Furthermore, while their response to deformation has been extensively studied, mechanisms contributing to their recovery from induced deformation remain poorly described in the literature. Here, we offer novel insights into the participation of proteoglycans (PG) and glycosaminoglycans (GAG) in regulating the nanoindentation creep deformation and recovery of mineralized and demineralized dentin. Accordingly, after the enzymatic digestion of either PGs and associated GAGs or only GAGs, the nanoindentation creep deformation of dentin increased significantly, while the relative recovery of both the mineralized and demineralized dentin dropped by 40-70%. In summary, our results suggest that PGs and GAGs may participate in a nanoscale mechanism that contributes significantly to the outstanding durability of dentin and possibly other mineralized tissues of similar composition.

  19. A molecular dynamics investigation into the size-dependent buckling behavior of a novel three-dimensional metallic carbon nanostructure (T6)

    Science.gov (United States)

    Ansari, R.; Ajori, S.; Hassani, R.

    2016-09-01

    The buckling behavior of a novel three-dimensional metallic carbon nanostructure known as T6 is investigated herein employing the molecular dynamics (MD) simulations. The models are prepared on the basis of two beam- and plate-like structures to study the effects of size and geometry on the critical buckling force and critical strain. It is observed that the range of critical force for the beam-like and plate-like T6 with different geometrical parameters is approximately identical. Moreover, it is demonstrated that the critical buckling force decreases and increases by increasing the length and the width of T6, respectively. Moreover, it is shown that critical strain of beam-like T6 decreases by increasing the length, whereas, in the case of plate-like T6, the critical strain only fluctuates around 2% by increasing the width. It is further found that the buckling parameters of T6 are not comparable with those of single-walled carbon nanotubes (SWCNTs) and graphene with a relatively similar dimension. The critical buckling force and critical strain of T6 are considerably smaller than those of SWCNT and larger than those of graphene.

  20. Creep-Fatigue Behavior of Alloy 617 at 850°C

    Energy Technology Data Exchange (ETDEWEB)

    Carroll, Laura [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-05-01

    Creep-fatigue deformation is expected to be a significant contributor to the potential factors that limit the useful life of the Intermediate Heat Exchanger (IHX) in the Very High Temperature Reactor (VHTR) nuclear system.[1] The IHX of a high temperature gas reactor will be subjected to a limited number of transient cycles due to start-up and shut-down operations imparting high local stresses on the component. This cycling introduces a creep-fatigue type of interaction as dwell times occur intermittently. The leading candidate alloy for the IHX is a nickel-base solid solution strengthened alloy, Alloy 617, which must safely operate near the expected reactor outlet temperature of up to 950 °C.[1] This solid solution strengthened nickel-base alloy provides an interesting creep-fatigue deformation case study because it has characteristics of two different alloy systems for which the cyclic behavior has been extensively investigated. Compositionally, it resembles nickel-base superalloys, such as Waspalloy, IN100, and IN718, with the exception of its lower levels of Al. At temperatures above 800 °C, the microstructure of Alloy 617, however, does not contain the ordered ?’ or ?’’ phases. Thus microstructurally, it is more similar to an austenitic stainless steel, such as 316 or 304, or Alloy 800H comprised of a predominantly solid solution strengthened matrix phase with a dispersion of inter- and intragranular carbides. Previous studies of the creep-fatigue behavior of Alloy 617 at 950 °C indicate that the fatigue life is reduced when a constant strain dwell is added at peak tensile strain.[2-5] This results from the combination of faster crack initiation occurring at surface-connected grain boundaries due to oxidation from the air environment along with faster, and intergranular, crack propagation resulting from the linking of extensive interior grain boundary cracking.[3] Saturation, defined as the point at which further increases in the strain

  1. Creep to inertia dominated stick-slip behavior in sliding friction modulated by tilted non-uniform loading

    Science.gov (United States)

    Tian, Pengyi; Tao, Dashuai; Yin, Wei; Zhang, Xiangjun; Meng, Yonggang; Tian, Yu

    2016-09-01

    Comprehension of stick-slip motion is very important for understanding tribological principles. The transition from creep-dominated to inertia-dominated stick-slip as the increase of sliding velocity has been described by researchers. However, the associated micro-contact behavior during this transition has not been fully disclosed yet. In this study, we investigated the stick-slip behaviors of two polymethyl methacrylate blocks actively modulated from the creep-dominated to inertia-dominated dynamics through a non-uniform loading along the interface by slightly tilting the angle of the two blocks. Increasing the tilt angle increases the critical transition velocity from creep-dominated to inertia-dominated stick-slip behaviors. Results from finite element simulation disclosed that a positive tilt angle led to a higher normal stress and a higher temperature on blocks at the opposite side of the crack initiating edge, which enhanced the creep of asperities during sliding friction. Acoustic emission (AE) during the stick-slip has also been measured, which is closely related to the different rupture modes regulated by the distribution of the ratio of shear to normal stress along the sliding interface. This study provided a more comprehensive understanding of the effect of tilted non-uniform loading on the local stress ratio, the local temperature, and the stick-slip behaviors.

  2. Buckling a Semiflexible Polymer Chain under Compression

    Directory of Open Access Journals (Sweden)

    Ekaterina Pilyugina

    2017-03-01

    Full Text Available Instability and structural transitions arise in many important problems involving dynamics at molecular length scales. Buckling of an elastic rod under a compressive load offers a useful general picture of such a transition. However, the existing theoretical description of buckling is applicable in the load response of macroscopic structures, only when fluctuations can be neglected, whereas membranes, polymer brushes, filaments, and macromolecular chains undergo considerable Brownian fluctuations. We analyze here the buckling of a fluctuating semiflexible polymer experiencing a compressive load. Previous works rely on approximations to the polymer statistics, resulting in a range of predictions for the buckling transition that disagree on whether fluctuations elevate or depress the critical buckling force. In contrast, our theory exploits exact results for the statistical behavior of the worm-like chain model yielding unambiguous predictions about the buckling conditions and nature of the buckling transition. We find that a fluctuating polymer under compressive load requires a larger force to buckle than an elastic rod in the absence of fluctuations. The nature of the buckling transition exhibits a marked change from being distinctly second order in the absence of fluctuations to being a more gradual, compliant transition in the presence of fluctuations. We analyze the thermodynamic contributions throughout the buckling transition to demonstrate that the chain entropy favors the extended state over the buckled state, providing a thermodynamic justification of the elevated buckling force.

  3. High temperature creep behavior of in-situ synthesized MoSi2-30%SiC composite

    Institute of Scientific and Technical Information of China (English)

    傅晓伟; 杨王玥; 孙祖庆; 张来启; 朱静

    2002-01-01

    The compressive creep behavior at 1200~1400℃ of an in-situ synt hesized MoSi2-30%SiC (volume fraction) composite and a traditional PM MoSi2 -30%SiC (volume fraction) composite is investigated. The creep rate of the in -situ synthesized MoSi2-30%SiC (volume fraction) composite is about 10- 7s-1 under stress of 60~120MPa, and significantly lower than that made by PM method above 1300℃. The reason is that the interface be tween SiC particle and MoSi2 matrix in in-situ synthesized SiCp/MoSi2 is of direct atomic bonding without any amorphous glassy phase, such as SiO2 stru cture. Creep deformation occurs primarily by dislocation motion and the dislocat ions have Burgers vectors of the ty pe of 〈110〉 and 〈100〉.

  4. The microstructure and impression creep behavior of cast Mg–4Sn–4Ca alloy

    Energy Technology Data Exchange (ETDEWEB)

    Khalilpour, Hamid, E-mail: Ha.Khalilpoorster@gmail.com [Shahid Rajaee Teacher Training University, Faculty of Mechanical Engineering, Lavizan, Tehran (Iran, Islamic Republic of); Mahdi Miresmaeili, Seyed, E-mail: s_m_miresmaeily@yahoo.com [Shahid Rajaee Teacher Training University, Faculty of Mechanical Engineering, Lavizan, Tehran (Iran, Islamic Republic of); Baghani, Amir, E-mail: amir-baghani@uiowa.edu [University of Iowa, Department of Mechanical and Industrial Engineering, Iowa City, IA (United States)

    2016-01-15

    Because of low creep properties of magnesium–aluminum alloys, magnesium–tin alloys have received much attention in applications where high mechanical properties in high temperatures required. In this study creep properties of Mg–4Sn–4Ca alloy were investigated by the aim of impression creep test, scanning electron microscopy, energy dispersion spectrometry and X-ray diffraction analysis. The impression creep tests were carried out under different shear modulus normalized stress at high temperatures. According to the measured stress exponent values and activation energies the climb-controlled dislocation creep was determined as the dominant mechanism. The creep resistance of this alloy was related to the presence of Ca–Mg–Sn and Mg{sub 2}Ca phases which are distributed uniformly in the matrix and exhibit high thermal stability.

  5. EXPERIMENTAL INVESTIGATION AND COMPUTER SIMULATION ON DYNAMIC BUCKLING BEHAVIOR OF LIQUID-FILLED CYLINDRICAL SHELLS UNDER AXIAL IMPACT

    Institute of Scientific and Technical Information of China (English)

    Zhang Shanyuan; Lei Jianping; Zhao Longmao; Cheng Guoqiang; Lu Guoyun

    2000-01-01

    This article reports an experimental investigation on the axial impact buckling of thin metallic cylindrical shells fully filled with water. Low velocity impact tests are carried out by DHR-9401 drop hammer rig. The whole process of dynamic buckling is simulated using LS-DYNA computer code. The consistency between experimental observation and numerical simulation is quite satisfactory. The investigation indicates that quite high internal hydrodynamic pressure occurs inside the shell during the impact process. Under the combined action of the high internal pressure and axial compression plastic buckling occurs easily in the thin walled shells and buckling modes take on regular and axisymmetric wrinkles.

  6. Creep behavior of a dispersion-strengthened Cu-Ti-Al alloy obtained by reaction milling

    Energy Technology Data Exchange (ETDEWEB)

    Espinoza, Rodrigo G. [Departamento de Ciencia de los Materiales, FCFM, Universidad de Chile, Av. Tupper 2069, Santiago 8370451 (Chile)], E-mail: roespino@ing.uchile.cl; Palma, Rodrigo H.; Sepulveda, Aquiles O.; Zuniga, Alejandro [Departamento de Ingenieria Mecanica, FCFM, Universidad de Chile, Beauchef 850, 4o Piso, Santiago 8370448 (Chile)

    2008-12-20

    Creep results of a dispersion-strengthened nominal-composition Cu-2.5 vol.%Ti-2.5 vol.%Al alloy, and the adjustment of those results to existing creep models, are presented. The alloy was prepared by reaction milling; its microstructural characterization by transmission electron microscopy had been recently reported elsewhere. Creep tests were here performed at 773, 973 and 1123 K, under loads that produced steady-state creep rates between 9 x 10{sup -7} and 2 x 10{sup -4} s{sup -1}. Two deformation models, available in the literature, were considered: dislocation creep, where the strain rate is controlled by the dislocation-particle interaction within the grains, and diffusional creep, controlled by the interaction between grain-boundary dislocations and particles. In all creep experiments the alloy exhibited high values of the apparent stress exponent, as typical for dispersion-strengthened alloys. Through model adjustment, the operating creep mechanisms where determined: at 773 and 1123 K, creep is controlled by dislocation/particle interactions taking place in the matrix and in grain boundaries, respectively, while at the intermediate temperature of 973 K, controlling dislocation-particle interactions would occur both in the matrix and in grain boundaries.

  7. DETERMINATION OF CREEP PARAMETERS FROM INDENTATION CREEP EXPERIMENTS

    Institute of Scientific and Technical Information of China (English)

    岳珠峰; 万建松; 吕震宙

    2003-01-01

    The possibilities of determining creep parameters for a simple Norton law material are explored from indentation creep testing. Using creep finite element analysis the creep indentation test technique is analyzed in terms of indentation rates at constant loads. Emphasis is placed on the relationships between the steady creep behavior of indentation systems and the creep property of the indented materials. The role of indenter geometry, size effects and macroscopic constraints is explicitly considered on indentation creep experiments. The influence of macroscopic constraints from the material systems becomes important when the size of the indenter is of the same order of magnitude as the size of the testing material. Two methods have been presented to assess the creep property of the indented material from the indentation experimental results on the single-phase-material and two-phase-material systems. The results contribute to a better mechanical understanding and extending the application of indentation creep testing.

  8. A Universal Reduced Rupture Creep Approach for Prediction of Long Term Failure Behavior of Aged Glass Polymers from the Short Term Test of Rupture Creep Compliance by the Unified Master Curved Extrapolation

    Institute of Scientific and Technical Information of China (English)

    Guang-jun Song; Da-ming Wu; Wei-yue Song; Ming-shi Song; Gui-xian Hu

    2012-01-01

    The prediction of long term failure behaviors and lifetime of aged glass polymers from the short term tests of reduced rupture creep compliance (or strain) is one of difficult problems in polymer science and engineering.A new "universal reduced rupture creep approach" with exact theoretical analysis and computations is proposed in this work.Failure by creep for polymeric material is an important problem to be addressed in the engineering.A universal equation on reduced extensional failure creep compliance for PMMA has been derived.It is successful in relating the reduced extensional failure creep compliance with aging time,temperature,levels of stress,the average growth dimensional number and the parameter in K-W-W function.Based on the universal equation,a method for the prediction of failure behavior,failure strain criterion,failure time of PMMA has been developed which is named as a universal "reduced rupture creep approach".The results show that the predicted failure strain and failure time of PMMA at different aging times for different levels of stress are all in agreement with those obtained directly from experiments,and the proposed method is reliable and practical.The dependences of reduced extensional failure creep compliance on the conditions of aging time,failure creep stress,the structure of fluidized-domain constituent chains are discussed.The shifting factor,exponent for time-stress superposition at different levels of stress and the shifting factor,exponent for time-time aging superposition at different aging time are theoretically defined respectively.

  9. Creep Behavior and Degradation of Subgrain Structures Pinned by Nanoscale Precipitates in Strength-Enhanced 5 to 12 Pct Cr Ferritic Steels

    Science.gov (United States)

    Ghassemi Armaki, Hassan; Chen, Ruiping; Maruyama, Kouichi; Igarashi, Masaaki

    2011-10-01

    Creep behavior and degradation of subgrain structures and precipitates of Gr. 122 type xCr-2W-0.4Mo-1Cu-VNb ( x = 5, 7, 9, 10.5, and 12 pct) steels were evaluated during short-term and long-term static aging and creep with regard to the Cr content of steel. Creep rupture life increased from 5 to 12 pct Cr in the short-term creep region, whereas in the long-term creep region, it increased up to 9 pct Cr and then decreased with the addition of Cr from 9 to 12 pct. Behavior of creep rupture life was attributed to the size of elongated subgrains. In the short-term creep region, subgrain size decreased from 5 to 12 pct Cr, corresponding to the longer creep strength. However, in the long-term creep region after 104 hours, subgrain size increased up to 9 pct Cr and then decreased from 9 to 12 pct, corresponding to the behavior of creep rupture life. M23C6 and MX precipitates had the highest number fraction among all of the precipitates present in the studied steels. Cr concentration dependence of spacing of M23C6 and MX precipitates exhibited a V-like shape during short-term as well as long-term aging at 923 K (650 °C), and the minimum spacing of precipitates belonged to 9 pct Cr steel, corresponding to the lowest recovery speed of subgrain structures. In the short-term creep region, subgrain coarsening during creep was controlled by strain and proceeded slower with the addition of Cr, whereas in long-term creep region, subgrain coarsening was controlled by the stability of precipitates rather than due to the creep plastic deformation and took place faster from 9 to 12 pct and 9 to 5 pct Cr. However, M23C6 precipitates played a more important role than MX precipitates in the control of subgrain coarsening, and there was a closer correlation between spacing of M23C6 precipitates and subgrain size during static aging and long-term creep region.

  10. Creep Effects in Pultruded FRP Beams

    Science.gov (United States)

    Boscato, G.; Casalegno, C.; Russo, S.

    2016-03-01

    The paper presents results of two creep tests on pultruded open-section GFRP beams aimed to evaluate the long-term deformations, the residual deflection after unloading, and the influence of creep strains on the flexuraltorsional buckling phenomenon. Two beams were subjected to a constant load for about one year. Then one of the beams was unloaded to evaluate its residual deflection. For the other beam, the load was increased up to failure, and the residual buckling strength was compared with that of a similar beam tested up to failure. The parameters of the Findley power law are evaluated, and the experimental results are compared with those of numerical analyses and with available formulations for prediction of the time-dependent properties of composite beams. Results of the investigation testify, in particular, to a noninsignificant time-dependent increment in deflections of the beams and to a significant reduction in their buckling strength due to creep deformations.

  11. 复合材料加筋板后屈曲特性研究%Study on Post-buckling Behavior of a Blade Stiffened Fiber Composite Panel

    Institute of Scientific and Technical Information of China (English)

    高晶晶; 关志东; 刘德博; 孙彦鹏

    2011-01-01

    Experimental and numerical investigations were conducted into the damage growth and collapse behavior of a composite blade-stiffened panel during the post-buckling period. The panel was loaded in compression to collapse, which was characterized by complex post-buckling damage, including stiffener debonding, fiber fracture, delamination, matrix cracking, etc. Hashin failure criterion and a quadratic stress-based adhesive failure criterion were introduced to the finite element model, both the buckling load and collapse load agree well with results from the experiment. It is found that the property of the interface is critical to the post-buckling behavior. Stiffeners withstand most of the load than skin after local buckling, stiffness allocation between skin and stiffeners should be given serious consideration during buckling and post-buckling design.%通过对复合材料加筋板进行轴向压缩实验和非线性有限元模拟,研究了其后屈曲阶段的损伤和破坏行为.加筋板在实验中被压缩至完全破坏,压溃的加筋板表现出复杂的后屈曲损伤,包括筋条脱粘、纤维断裂、分层、基体开裂等损伤模式.有限元模型中引入了Hashin准则和基于二次应力的胶层失效准则,失稳及破坏载荷的预测结果和实验值吻合较好.分析表明:胶结界面对复合材料加筋板的后屈曲性能有重要影响;局部失稳后蒙皮承载能力变弱,筋条承受主要载荷,蒙皮、筋条刚度分配应该是结构屈曲和后屈曲设计时重点考虑的问题.

  12. Creep Crack Growth Behavior of Alloys 617 and 800H in Air and Impure Helium Environments at High Temperatures

    Science.gov (United States)

    Grierson, D. S.; Cao, G.; Brooks, P.; Pezzi, P.; Glaudell, A.; Kuettel, D.; Fischer, G.; Allen, T.; Sridharan, K.; Crone, W. C.

    2016-11-01

    The environmental degradation of intermediate heat exchanger (IHX) materials in impure helium has been identified as an area with major ramifications on the design of very high-temperature reactors (VHTR). It has been reported that in some helium environments, non-ductile failure is a significant failure mode for Alloy 617 with long-term elevated-temperature service. Non-ductile failure of intermediate exchangers can result in catastrophic consequences; unfortunately, the knowledge of creep crack initiation and creep crack growth (CCG) in candidate alloys is limited. Current codes and code cases for the candidate alloys do not provide specific guidelines for effects of impure helium on the high-temperature behavior. The work reported here explores creep crack growth characterization of Alloy 617 and Alloy 800H at elevated temperatures in air and in impure helium environments, providing information on the reliability of these alloys in VHTR for long-term service. Alloy 617 was found to exhibit superior CCG resistance compared to Alloy 800H. For Alloy 617 tested at 973 K (700 °C), a notable increase in the resistance to crack growth was measured in air compared to that measured in the helium environment; CCG results for Alloy 800H suggest that air and helium environments produce similar behavior. Testing of grain boundary-engineered (GBE) Alloy 617 samples revealed that, although the technique produces superior mechanical properties in many respects, the GBE samples exhibited inferior resistance to creep crack growth compared to the other Alloy 617 samples tested under similar conditions. Grain size is noted as a confounding factor in creep crack growth resistance.

  13. Creep Crack Growth Behavior of Alloys 617 and 800H in Air and Impure Helium Environments at High Temperatures

    Science.gov (United States)

    Grierson, D. S.; Cao, G.; Brooks, P.; Pezzi, P.; Glaudell, A.; Kuettel, D.; Fischer, G.; Allen, T.; Sridharan, K.; Crone, W. C.

    2017-03-01

    The environmental degradation of intermediate heat exchanger (IHX) materials in impure helium has been identified as an area with major ramifications on the design of very high-temperature reactors (VHTR). It has been reported that in some helium environments, non-ductile failure is a significant failure mode for Alloy 617 with long-term elevated-temperature service. Non-ductile failure of intermediate exchangers can result in catastrophic consequences; unfortunately, the knowledge of creep crack initiation and creep crack growth (CCG) in candidate alloys is limited. Current codes and code cases for the candidate alloys do not provide specific guidelines for effects of impure helium on the high-temperature behavior. The work reported here explores creep crack growth characterization of Alloy 617 and Alloy 800H at elevated temperatures in air and in impure helium environments, providing information on the reliability of these alloys in VHTR for long-term service. Alloy 617 was found to exhibit superior CCG resistance compared to Alloy 800H. For Alloy 617 tested at 973 K (700 °C), a notable increase in the resistance to crack growth was measured in air compared to that measured in the helium environment; CCG results for Alloy 800H suggest that air and helium environments produce similar behavior. Testing of grain boundary-engineered (GBE) Alloy 617 samples revealed that, although the technique produces superior mechanical properties in many respects, the GBE samples exhibited inferior resistance to creep crack growth compared to the other Alloy 617 samples tested under similar conditions. Grain size is noted as a confounding factor in creep crack growth resistance.

  14. Creep behavior in interlaminar shear of a Hi-Nicalon™/SiC–B{sub 4}C composite at 1200 °C in air and in steam

    Energy Technology Data Exchange (ETDEWEB)

    Ruggles-Wrenn, M.B., E-mail: marina.ruggles-wrenn@afit.edu; Pope, M.T.; Zens, T.W.

    2014-07-29

    Creep behavior in interlaminar shear of a non-oxide ceramic composite with a multilayered matrix was investigated at 1200 °C in laboratory air and in steam environment. The composite was produced via chemical vapor infiltration (CVI). The composite had an oxidation inhibited matrix, which consisted of alternating layers of silicon carbide and boron carbide and was reinforced with laminated Hi-Nicalon™ fibers woven in a five-harness-satin weave. Fiber preforms had pyrolytic carbon fiber coating with boron carbon overlay applied. The interlaminar shear properties were measured. The creep behavior was examined for interlaminar shear stresses in the 16–22 MPa range. Primary and secondary creep regimes were observed in all tests conducted in air and in steam. In air and in steam, creep run-out defined as 100 h at creep stress was achieved at 16 MPa. Similar creep strains were accumulated in air and in steam. Furthermore, creep strain rates and creep lifetimes were only moderately affected by the presence of steam. The retained properties of all specimens that achieved run-out were characterized. Composite microstructure, as well as damage and failure mechanisms were investigated. The tested specimens were also examined using electron probe microanalysis (EPMA) with wavelength dispersive spectroscopy (WDS). Analysis of the fracture surfaces revealed significant surface oxidation, but only trace amounts of boron and carbon. Cross sectional analysis showed increasing boron concentration in the specimen interior.

  15. Creep behavior in interlaminar shear of a Hi-NicalonTM/ SiC-B4C composite at 1200∘C in air and in steam

    Directory of Open Access Journals (Sweden)

    Ruggles-Wrenn Marina

    2015-01-01

    Full Text Available Creep behavior in interlaminar shear of a non-oxide ceramic composite with a multilayered matrix was investigated at 1200∘C in laboratory air and in steam environment. The composite was produced via chemical vapor infiltration (CVI. The composite had an oxidation inhibited matrix, which consisted of alternating layers of silicon carbide and boron carbide and was reinforced with laminated Hi-NicalonTM fibers woven in a five-harness-satin weave. Fiber preforms had pyrolytic carbon fiber coating with boron carbon overlay applied. The interlaminar shear properties were measured. The creep behavior was examined for interlaminar shear stresses in the 16–22 MPa range. Primary and secondary creep regimes were observed in all tests conducted in air and in steam. In air and in steam, creep run-out defined as 100 h at creep stress was achieved at 16 MPa. Similar creep strains were accumulated in air and in steam. Furthermore, creep strain rates and creep lifetimes were only moderately affected by the presence of steam. The retained properties of all specimens that achieved run-out were characterized. Composite microstructure, as well as damage and failure mechanisms were investigated. The tested specimens were also examined using electron probe microanalysis (EPMA with wavelength dispersive spectroscopy (WDS. Analysis of the fracture surfaces revealed significant surface oxidation, but only trace amounts of boron and carbon. Cross sectional analysis showed increasing boron concentration in the specimen interior.

  16. Effect of fiber-matrix adhesion on the creep behavior of CF/PPS composites: temperature and physical aging characterization

    Science.gov (United States)

    Motta Dias, M. H.; Jansen, K. M. B.; Luinge, J. W.; Bersee, H. E. N.; Benedictus, R.

    2016-06-01

    The influence of fiber-matrix adhesion on the linear viscoelastic creep behavior of `as received' and `surface modified' carbon fibers (AR-CF and SM-CF, respectively) reinforced polyphenylene sulfide (PPS) composite materials was investigated. Short-term tensile creep tests were performed on ±45° specimens under six different isothermal conditions, 40, 50, 60, 65, 70 and 75 °C. Physical aging effects were evaluated on both systems using the short-term test method established by Struik. The results showed that the shapes of the curves were affected neither by physical aging nor by the test temperature, allowing then superposition to be made. A unified model was proposed with a single physical aging and temperature-dependent shift factor, a_{T,te}. It was suggested that the surface treatment carried out in SM-CF/PPS had two major effects on the creep response of CF/PPS composites at a reference temperature of 40 °C: a lowering of the initial compliance of about 25 % and a slowing down of the creep response of about 1.1 decade.

  17. The Dependence of Creep Behavior on Elemental Partitioning in Mg-5Al-3Ca- xSn Alloys

    Science.gov (United States)

    TerBush, Jessica R.; Chen, Olivia H.; Jones, J. Wayne; Pollock, Tresa M.

    2012-09-01

    Cast Mg-5Al-3Ca- xSn alloys have been examined to investigate the effect of Sn additions on elemental partitioning during solidification, microstructure development, and compressive creep behavior at 453 K (180 °C). Alloys containing 0.25 to 3.0 wt pct Sn were cast with a permanent mold technique. The addition of 0.75 to 1.0 wt pct Sn had a beneficial effect on Ca partitioning to the α-Mg phase. Additions beyond 1 wt pct Sn resulted in the formation of an orthorhombic Mg-Ca-Sn phase, with decreased Ca partitioning to the α-Mg. A lower minimum creep rate was observed for the Mg-5Al-3Ca- xSn alloy with increased Ca partitioning. Consistent with this finding, analyses that consider the influence of solute and precipitation strengthening on creep in Mg-5Al-3Ca- xSn alloys suggest that Ca in the α-Mg contributes to a greater degree than Al in solution to the creep resistance at 453 K (180 °C).

  18. Coupling between creep and redox behavior in nickel - yttria stabilized zirconia observed in-situ by monochromatic neutron imaging

    Science.gov (United States)

    Makowska, Malgorzata Grazyna; Kuhn, Luise Theil; Frandsen, Henrik Lund; Lauridsen, Erik Mejdal; De Angelis, Salvatore; Cleemann, Lars Nilausen; Morgano, Manuel; Trtik, Pavel; Strobl, Markus

    2017-02-01

    Ni-YSZ (nickel - yttria stabilized zirconia) is a material widely used for electrodes and supports in solid oxide electrochemical cells. The mechanical and electrochemical performance of these layers, and thus the whole cell, depends on their microstructure. During the initial operation of a cell, NiO is reduced to Ni. When this process is conducted under external load, like also present in a stack assembly, significant deformations of NiO/Ni-YSZ composite samples are observed. The observed creep is orders of magnitude larger than the one observed after reduction during operation. This phenomenon is referred to as accelerated creep and is expected to have a significant influence on the microstructure development and stress field present in the Ni-YSZ in solid oxide electrochemical cells (SOCs), which is highly important for the durability of the SOC. In this work we present energy selective neutron imaging studies of the accelerated creep phenomenon in Ni/NiO-YSZ composite during reduction and also during oxidation. This approach allowed us to observe the phase transition and the creep behavior simultaneously in-situ under SOC operation-like conditions.

  19. A novel on chip test method to characterize the creep behavior of metallic layers under heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Lapouge, P., E-mail: pierre.lapouge@cea.fr [Service de recherches Métallurgiques Appliquées, CEA Saclay 91191 Gif-sur-Yvette (France); Onimus, F. [Service de recherches Métallurgiques Appliquées, CEA Saclay 91191 Gif-sur-Yvette (France); Vayrette, R. [Institute of Mechanics, Materials and Civil Engineering, Université catholique de Louvain, 1348, Louvain-la-Neuve (Belgium); Institute of Information and Communication Technologies, Electronics and Applied Mathematics, Université catholique de Louvain, 1348, Louvain-la-Neuve (Belgium); Raskin, J.-P. [Institute of Information and Communication Technologies, Electronics and Applied Mathematics, Université catholique de Louvain, 1348, Louvain-la-Neuve (Belgium); Research Center in Micro and Nanoscopic Materials and Electronic Devices, Université catholique de Louvain, 1348, Louvain-la-Neuve (Belgium); Pardoen, T. [Institute of Mechanics, Materials and Civil Engineering, Université catholique de Louvain, 1348, Louvain-la-Neuve (Belgium); Research Center in Micro and Nanoscopic Materials and Electronic Devices, Université catholique de Louvain, 1348, Louvain-la-Neuve (Belgium); Bréchet, Y. [CNRS SIMAP/Univ. Grenoble Alpes, F-3800, Grenoble (France)

    2016-08-01

    An on chip test method has been developed to characterize the irradiation creep behavior of thin freestanding films under uniaxial tension. The method is based on the use of a long beam involving large internal stress protected from the irradiation flux that imposes a spring like deformation to a specimen beam. These elementary freestanding structures fabricated using a combination of deposition, lithography and release steps are multiplied with different dimensions in order to test different levels of stress and of initial plastic deformation. The method has been validated on 200 and 500 nm thick copper films under heavy copper ions irradiation. The irradiation creep rate is shown to be at least one order of magnitude larger than in the absence of irradiation. - Highlights: • On chip method developed to test freestanding films under ion irradiation. • Several tens of in situ irradiation creep tests performed simultaneously. • Technique successfully validated on 200 and 500 nm thick Cu films. • Fast creep rates measured in Cu films due to irradiation.

  20. Creep Behavior of Hafnia and Ytterbium Silicate Environmental Barrier Coating Systems on SiC/SiC Ceramic Matrix Composites

    Science.gov (United States)

    Zhu, Dongming; Fox, Dennis S.; Ghosn, Louis J.; Harder, Bryan

    2011-01-01

    Environmental barrier coatings will play a crucial role in future advanced gas turbine engines because of their ability to significantly extend the temperature capability and stability of SiC/SiC ceramic matrix composite (CMC) engine components, thus improving the engine performance. In order to develop high performance, robust coating systems for engine components, appropriate test approaches simulating operating temperature gradient and stress environments for evaluating the critical coating properties must be established. In this paper, thermal gradient mechanical testing approaches for evaluating creep and fatigue behavior of environmental barrier coated SiC/SiC CMC systems will be described. The creep and fatigue behavior of Hafnia and ytterbium silicate environmental barrier coatings on SiC/SiC CMC systems will be reported in simulated environmental exposure conditions. The coating failure mechanisms will also be discussed under the heat flux and stress conditions.

  1. Microstructural Evolution and Creep-Rupture Behavior of Fusion Welds Involving Alloys for Advanced Ultrasupercritical Power Generation

    Science.gov (United States)

    Bechetti, Daniel H., Jr.

    Projections for large increases in the global demand for electric power produced by the burning of fossil fuels, in combination with growing environmental concerns surrounding these fuel sources, have sparked initiatives in the United States, Europe, and Asia aimed at developing a new generation of coal fired power plant, termed Advanced Ultrasupercritical (A-USC). These plants are slated to operate at higher steam temperatures and pressures than current generation plants, and in so doing will offer increased process cycle efficiency and reduced greenhouse gas emissions. Several gamma' precipitation strengthened Ni-based superalloys have been identified as candidates for the hottest sections of these plants, but the microstructural instability and poor creep behavior (compared to wrought products) of fusion welds involving these alloys present significant hurdles to their implementation and a gap in knowledge that must be addressed. In this work, creep testing and in-depth microstructural characterization have been used to provide insight into the long-term performance of these alloys. First, an investigation of the weld metal microstructural evolution as it relates to creep strength reductions in A-USC alloys INCONELRTM 740, NIMONICRTM 263 (INCONEL and NIMONIC are registered trademarks of Special Metals Corporation), and HaynesRTM 282RTM (Haynes and 282 are registered trademarks of Haynes International) was performed. gamma'-precipitate free zones were identified in two of these three alloys, and their development was linked to the evolution of phases that precipitate at the expense of gamma'. Alloy 282 was shown to avoid precipitate free zone formation because the precipitates that form during long term aging in this alloy are poor in the gamma'-forming elements. Next, the microstructural evolution of INCONELRTM 740H (a compositional variant of alloy 740) during creep was investigated. Gleeble-based interrupted creep and creep-rupture testing was used to

  2. Rate Dependence and Short-Term Creep Behavior of PMR-15 Neat Resin at 23 and 288 deg C

    Science.gov (United States)

    2005-09-01

    applicability of VBO to six different polymers: polycarbonate (PC), Nylon 66, high-density polyethylene (HDPE), polyethylene - terephthalate ( PET ...Pre-Necking and Post-Necking Relaxation and Creep Behavior of Polycarbonate : A Phenomenological Study,” Polymer Engineering and Science, 44:1783...and Ian D. Moore. “Nonlinear Mechanical Response of High Density Polyethylene . Part I: Experimental Investigation and Model Evaluation,” Polymer

  3. Creep Behavior of Porous Supports in Metal-support Solid Oxide Fuel Cells

    DEFF Research Database (Denmark)

    Boccaccini, Dino; Frandsen, Henrik Lund; Blennow Tullmar, Peter;

    2013-01-01

    Creep is the inelastic deformation of a material at high temperatures over long periods of time. It can be defined as timedependent deformation at absolute temperatures greater than one half the absolute melting. Creep resistance is a key parameter for high temperature steel components, e.g. SOFC...... by means of a thermo mechanical analyzer (TMA) for stresses in the range of 1-17 MPa and temperatures between 650-750 °C. The creep parameters of Crofer® 22 APU were also acquired and compared with values obtained from literature to validate the technique....

  4. Creep behavior of a novel Co-Al-W-base single crystal alloy containing Ta and Ti at 982 ∘C

    Directory of Open Access Journals (Sweden)

    Xue Fei

    2014-01-01

    Full Text Available The tensile creep behavior of a Co-Al-W-base single crystal alloy containing Ta and Ti was investigated at 982 ∘C and 248 MPa. The lattice misfit of experimental alloy was measured to be positive by synchrotron X-ray diffraction at high temperature, and long term heat treatment at 1000 ∘C for 1000 h revealed a γ′ volume fraction of 75% without secondary phases. The creep test indicated that the creep properties of experimental alloy exceeded commercial 1st generation Ni-base single crystal superalloy CMSX-3 with respect to the rupture life. The initial cuboidal γ′ precipitates directionally coarsened parallel to the applied stress axis during the creep process. The stacking faults in {111} planes within γ′ rafts were the primary creep deformation mode by TEM investigation.

  5. Effect of Double Aging Heat Treatment on the Short-Term Creep Behavior of the Inconel 718

    Science.gov (United States)

    Caliari, Felipe Rocha; Candioto, Kátia Cristiane Gandolpho; Couto, Antônio Augusto; Nunes, Carlos Ângelo; Reis, Danieli Aparecida Pereira

    2016-06-01

    This research studies the effect of double aging heat treatment on the short-term creep behavior of the superalloy Inconel 718. The superalloy, received in the solution treated state, was subjected to an aging treatment which comprises a solid solution at 1095 °C for 1 h, a first aging step of 955 °C for 1 h, then aged at 720 and 620 °C, 8 h each step. Creep tests at constant load mode, under temperatures of 650, 675, 700 °C and stress of 510, 625 and 700 MPa, were performed before and after heat treatment. The results indicate that after the double aging heat treatment creep resistance is increased, influenced by the presence of precipitates γ' and γ″ and its interaction with the dislocations, by grain size growth (from 8.20 to 7.23 ASTM) and the increase of hardness by approximately 98%. Creep parameters of primary and secondary stages have been determined. There is a breakdown relationship between dot{\\upvarepsilon }_{{s}} and stress at 650 °C of Inconel 718 as received, around 600 MPa. By considering the internal stress values, effective stress exponent, effective activation energy, and TEM images of Inconel 718 double aged, it is suggested that the creep mechanism is controlled by the interaction of dislocations with precipitates. The fracture mechanism of Inconel 718 as received is transgranular (coalescence of dimples) and mixed (transgranular-intergranular), whereas the Inconel 718 double aged condition crept surfaces evidenced the intergranular fracture mechanism.

  6. Improved creep and oxidation behavior of a martensitic 9Cr steel by the controlled addition of boron and nitrogen

    Energy Technology Data Exchange (ETDEWEB)

    Mayr, Peter [Massachusetts Institute of Technology, Cambridge, MA (United States). Dept. of Materials Science; Graz Univ. of Technology (Austria). Inst. of Material Science and Welding; Holzer, Ivan; Mendez-Martin, Francisca [Graz Univ. of Technology (Austria). Inst. of Material Science and Welding; Albu, Mihaela; Mitsche, Stefan [Graz Univ. of Technology (Austria). Inst. for Electron Microscopy; Gonzalez, Vanessa; Agueero, Alina [Instituto Nacional de Tecnica Aeroespacial, Torrejon de Ardoz (Spain)

    2010-07-01

    This manuscript gives an overview on recent developments of a martensitic steel grade based on 9Cr3W3CoVNb with controlled additions of boron and nitrogen. Alloy design by thermodynamic equilibrium calculations and calculation of boron-nitrogen solubility is discussed. Out of this alloy design process, two melts of a 9Cr3W3CoVNbBN steel were produced. The investigation focused on microstructural evolution during high temperature exposure, creep properties and oxidation resistance in steam at 650 C. Microstructural characterization of ''as-received'' and creep exposed material was carried out using conventional optical as well as advanced electron microscopic methods. Creep data at 650 was obtained at various stress levels. Longest-running specimens have reached more than 20,000 hours of testing time. In parallel, long-term oxidation resistance has been studied at 650 C in steam atmosphere up to 5,000 hours. Preliminary results of the extensive testing program on a 9Cr3W3CoVNbBN steel show significant improvement in respect to creep strength and oxidation resistance compared to the state-of-the-art 9 wt. % Cr martensitic steel grades. Up to current testing times, the creep strength is significantly beyond the +20% scatterband of standard grade P92 material. Despite the chromium content of 9 wt % the material exhibits excellent oxidation resistance. Steam exposed plain base material shows comparable oxidation behavior to coated material, and the corrosion rate of the boron-nitrogen controlled steel is much lower compared to standard 9 wt % Cr steel grades, P91 and P92. (orig.)

  7. Antiskid control of railway train braking based on adhesion creep behavior

    Science.gov (United States)

    Zuo, Jianyong; Chen, Zhongkai

    2012-05-01

    In modern trains wheelset skidding leads to the deterioration of braking behavior, the degradation of comfort, as well as a boost in system hazards. Because of the nonlinearity and unknown characteristics of wheelset adhesion, simplifications are widely adopted in the modeling process of conventional antiskid controllers. Therefore, conventional antiskid controllers usually cannot perform satisfactorily. In this paper, systematic computer simulation and field tests for railway antiskid control system are introduced. The operating principal of antiskid control system is explained, which is fundamental to the simulation of antiskid brakes, and the simulation model is introduced, which incorporates both the adhesion creep curve and a pneumatic submodel of antiskid control system. In addition, the characteristics of adhesion curves and the simulation target are also provided. Using DHSplus, the pneumatic submodel is created to analyze the performance of the different control strategies of antiskid valves. Then the system simulation is realized by combining the kinematical characteristics of railway trains and the pneumatic submodel. The simulation is performed iteratively to obtain the optimized design of the antiskid control system. The design result is incorporated in the hardware design of the antiskid control system and is evaluated in the field tests in Shanghai Subway Line 1. Judging by the antiskid efficiency, the antiskid braking performance observed in the field tests shows the superiority of the optimized design. Therefore, the proposed simulation method, especially in view of its ease of application, appears to be a useful one for designing railway antiskid control systems.

  8. Mechanisms of high-temperature, solid-state flow in minerals and ceramics and their bearing on the creep behavior of the mantle

    Science.gov (United States)

    Kirby, S.H.; Raleigh, C.B.

    1973-01-01

    The problem of applying laboratory silicate-flow data to the mantle, where conditions can be vastly different, is approached through a critical review of high-temperature flow mechanisms in ceramics and their relation to empirical flow laws. The intimate association of solid-state diffusion and high-temperature creep in pure metals is found to apply to ceramics as well. It is shown that in ceramics of moderate grain size, compared on the basis of self-diffusivity and elastic modulus, normalized creep rates compare remarkably well. This comparison is paralleled by the near universal occurrence of similar creep-induced structures, and it is thought that the derived empirical flow laws can be associated with dislocation creep. Creep data in fine-grained ceramics, on the other hand, are found to compare poorly with theories involving the stress-directed diffusion of point defects and have not been successfully correlated by self-diffusion rates. We conclude that these fine-grained materials creep primarily by a quasi-viscous grain-boundary sliding mechanism which is unlikely to predominate in the earth's deep interior. Creep predictions for the mantle reveal that under most conditions the empirical dislocation creep behavior predominates over the mechanisms involving the stress-directed diffusion of point defects. The probable role of polymorphic transformations in the transition zone is also discussed. ?? 1973.

  9. A Reduction Factor for Buckling Load of Spherical Cap Shells

    Directory of Open Access Journals (Sweden)

    P.N. Khakina

    2011-12-01

    Full Text Available The classical buckling theory usually overestimates the buckling load of shells. In this study, a reduction factor is determined using geometrical parameters so as to reduce the classical buckling load to a more realistic value based on the post-buckling load. It is observed that the buckling load is directly proportional to the thickness and rise and inversely proportional to the span of the spherical cap. Finite element modeling and simulation using ABAQUS was conducted to determine the buckling behavior of a spherical cap shell subjected to different initial geometrical imperfections. The load-deflection curves drawn from the simulation formed a plateau at the post-buckling load. It is observed that as the initial geometrical imperfection is increased, the value of the initial buckling load is almost the same as the value of the post-buckling load on the plateau. The results obtained from different shells were used to derive a formula for the reduction factor.

  10. Negative creep in nickel base superalloys

    DEFF Research Database (Denmark)

    Dahl, Kristian Vinter; Hald, John

    2004-01-01

    Negative creep describes the time dependent contraction of a material as opposed to the elongation seen for a material experiencing normal creep behavior. Negative creep occurs because of solid state transformations that results in lattice contractions. For most applications negative creep will h...

  11. A novel on chip test method to characterize the creep behavior of metallic layers under heavy ion irradiation

    Science.gov (United States)

    Lapouge, P.; Onimus, F.; Vayrette, R.; Raskin, J.-P.; Pardoen, T.; Bréchet, Y.

    2016-08-01

    An on chip test method has been developed to characterize the irradiation creep behavior of thin freestanding films under uniaxial tension. The method is based on the use of a long beam involving large internal stress protected from the irradiation flux that imposes a spring like deformation to a specimen beam. These elementary freestanding structures fabricated using a combination of deposition, lithography and release steps are multiplied with different dimensions in order to test different levels of stress and of initial plastic deformation. The method has been validated on 200 and 500 nm thick copper films under heavy copper ions irradiation. The irradiation creep rate is shown to be at least one order of magnitude larger than in the absence of irradiation.

  12. A Physics-Based Crystallographic Modeling Framework for Describing the Thermal Creep Behavior of Fe-Cr Alloys

    Science.gov (United States)

    Wen, W.; Capolungo, L.; Patra, A.; Tomé, C. N.

    2017-02-01

    In this work, a physics-based thermal creep model is developed based on the understanding of the microstructure in Fe-Cr alloys. This model is associated with a transition state theory-based framework that considers the distribution of internal stresses at sub-material point level. The thermally activated dislocation glide and climb mechanisms are coupled in the obstacle-bypass processes for both dislocation and precipitate-type barriers. A kinetic law is proposed to track the dislocation densities evolution in the subgrain interior and in the cell wall. The predicted results show that this model, embedded in the visco-plastic self-consistent framework, captures well the creep behaviors for primary and steady-state stages under various loading conditions. The roles of the mechanisms involved are also discussed.

  13. A physics-based crystallographic modeling framework for describing the thermal creep behavior of Fe-Cr alloys

    Energy Technology Data Exchange (ETDEWEB)

    Wen, Wei [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Capolungo, Laurent [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Patra, Anirban [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Tome, Carlos [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-02-02

    This Report addresses the Milestone M2MS-16LA0501032 of NEAMS Program (“Develop hardening model for FeCrAl cladding), with a deadline of 09/30/2016. Here we report a constitutive law for thermal creep of FeCrAl. This Report adds to and complements the one for Milestone M3MS-16LA0501034 (“Interface hardening models with MOOSE-BISON”), where we presented a hardening law for irradiated FeCrAl. The last component of our polycrystal-based constitutive behavior, namely, an irradiation creep model for FeCrAl, will be developed as part of the FY17 Milestones, and the three regimes will be coupled and interfaced with MOOSE-BISON.

  14. Creep in amorphous metals

    Directory of Open Access Journals (Sweden)

    Michael E. Kassner

    2015-01-01

    Full Text Available This paper reviews the work on creep behavior of amorphous metals. There have been, over the past several years, a few reviews of the mechanical behavior of amorphous metals. Of these, the review of the creep properties of amorphous metals by Schuh et al. though oldest of the three, is particularly noteworthy and the reader is referred to this article published in 2007. The current review of creep of amorphous metals particularly focuses on those works since that review and places the work prior to 2007 in a different context where new developments warrant.

  15. The Effect of Creep Aging on the Fatigue Fracture Behavior of 2524 Aluminum Alloy

    Directory of Open Access Journals (Sweden)

    Wenke Li

    2016-09-01

    Full Text Available Normal temperature tensile and fatigue tests were adopted to test the mechanical performance and fatigue life of 2524 aluminum alloy under the three states of T3, artificial aging, and creep aging, and scanning electron microscope and transmission electron microscope were also used to observe the fatigue fracture morphology and aging precipitation features of the alloy under the above three states. Results showed that the alloy treated by creep aging can obtain higher fatigue life, but that treated by artificial aging is lower than T3; T3 alloy is mainly dominated by GPB region. Meanwhile, the crystal boundary displays continuously distributed fine precipitated phases; after artificial aging and creep aging treatment, a large amount of needle-shaped S′ phases precipitate inside the alloy, while there are wide precipitated phases at the crystal boundary. Wide precipitation free zones appear at the crystal boundary of artificial-aging samples, but precipitation free zones at the alloy crystal boundary of creep aging become narrower and even disappear. It can be seen that creep aging can change the precipitation features of the alloy and improve its fatigue life.

  16. Deterministic Multiaxial Creep and Creep Rupture Enhancements for CARES/Creep Integrated Design Code

    Science.gov (United States)

    Jadaan, Osama M.

    1998-01-01

    High temperature and long duration applications of monolithic ceramics can place their failure mode in the creep rupture regime. A previous model advanced by the authors described a methodology by which the creep rupture life of a loaded component can be predicted. That model was based on the life fraction damage accumulation rule in association with the modified Monkman-Grant creep rupture criterion. However, that model did not take into account the deteriorating state of the material due to creep damage (e.g., cavitation) as time elapsed. In addition, the material creep parameters used in that life prediction methodology, were based on uniaxial creep curves displaying primary and secondary creep behavior, with no tertiary regime. The objective of this paper is to present a creep life prediction methodology based on a modified form of the Kachanov-Rabotnov continuum damage mechanics (CDM) theory. In this theory, the uniaxial creep rate is described in terms of sum, temperature, time, and the current state of material damage. This scalar damage state parameter is basically an abstract measure of the current state of material damage due to creep deformation. The damage rate is assumed to vary with stress, temperature, time, and the current state of damage itself. Multiaxial creep and creep rupture formulations of the CDM approach are presented in this paper. Parameter estimation methodologies based on nonlinear regression analysis are also described for both, isothermal constant stress states and anisothermal variable stress conditions This creep life prediction methodology was preliminarily added to the integrated design code CARES/Creep (Ceramics Analysis and Reliability Evaluation of Structures/Creep), which is a postprocessor program to commercially available finite element analysis (FEA) packages. Two examples, showing comparisons between experimental and predicted creep lives of ceramic specimens, are used to demonstrate the viability of Ns methodology and the

  17. Creep rupture behavior of candidate materials for nuclear process heat applications

    Energy Technology Data Exchange (ETDEWEB)

    Schubert, F.; te Heesen, E.; Bruch, U.; Cook, R.; Diehl, H.; Ennis, P.J.; Jakobeit, W.; Penkalla, H.J.; Ullrich, G.

    1984-08-01

    Creep and stress rupture properties are determined for the candidate materials to be used in hightemperature gas-cooled reactor (HTGR) components. The materials and test methods are briefly described based on experimental results of test durations of about20000 h. The medium creep strengths of the alloys Inconel-617, Hastelloy-X, Nimonic-86, Hastelloy-S, Manaurite-36X, IN-519, and Incoloy-800H are compared showing that Inconel-617 has the best creep rupture properties in the temperature range above 800/sup 0/C. The rupture time of welded joints is in the lower range of the scatterband of the parent metal. The properties determined in different simulated HTGR atmospheres are within the scatterband of the properties obtained in air. Extrapolation methods are discussed and a modified minimum commitment method is favored.

  18. Buckling of Bucket Foundations

    DEFF Research Database (Denmark)

    Madsen, Søren; Andersen, Lars Vabbersgaard; Ibsen, Lars Bo

    2012-01-01

    In this paper, the risk of structural buckling during installation of large-diameter bucket foundations is addressed using numerical methods. Imperfect geometries are introduced based on the pre-buckling mode shapes from a linear Eigenvalue buckling analysis. Various imperfect geometries...... are introduced to reveal how sensitive the buckling load is to the mentioned imperfections. Including the first 21 mode shapes as imperfect geometries reduces the buckling pressure compared to only considering mode 1....

  19. Fractal and probability analysis of creep crack growth behavior in 2.25Cr–1.6W steel incorporating residual stresses

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Mengjia; Xu, Jijin, E-mail: xujijin_1979@sjtu.edu.cn; Lu, Hao; Chen, Jieshi; Chen, Junmei; Wei, Xiao

    2015-12-30

    Graphical abstract: - Highlights: • Statistical and fractal analysis is applied to study the creep fracture surface. • The tensile residual stresses promote the initiation of creep crack. • The fractal dimension of a mixed mode fracture surface shows a wavy variation. • The fractal dimension increases with increasing intergranular fracture percentage. • Height coordinates of intergranular fracture surface fit Gaussian distribution. - Abstract: In order to clarify creep crack growth behavior in 2.25Cr–1.6W steel incorporating residual stresses, creep crack tests were carried out on the tension creep specimens, in which the residual stresses were generated by local remelting and cooling. Residual stresses in the specimens were measured using Synchrotron X-ray diffraction techniques. The fracture surface of the creep specimen was analyzed using statistical methods and fractal analysis. The relation between fractal dimension of the fracture surface and fracture mode of the creep specimen was discussed. Due to different fracture mechanisms, the probability density functions of the height coordinates vary with the intergranular crack percentage. Good fitting was found between Gaussian distribution and the probability function of height coordinates of the high percentage intergranular crack surface.

  20. Precipitation behavior of Z phase after long-term creep in high chromium ferritic heat resistant steels

    Energy Technology Data Exchange (ETDEWEB)

    Sawada, K.; Kushima, H.; Kimura, K. [National Institute for Materials Science, Tsukuba (Japan). Materials Reliability Center

    2006-07-01

    The precipitation behavior of the Z phase was investigated after long-term creep exposure in ASME-T91, T92, T122 without {delta}-ferrite, and T122 with {delta}-ferrite through elemental mapping using EF-TEM. The Z phase was identified by comparing the Cr map with the V map. Most of the Z phase was observed around prior austenite grain boundaries and/or packet boundaries in all of the steels examined. In T122 with {delta}-ferrite, the Z phase also precipitates around the {delta}-ferrite. In particular, the number of MX carbonitrides was very small in T122 with a large amount of the Z phase. The main metallic composition of the Z phase in T91 was the same as that in T92. In T122, the Z phase contained a lower Nb content. The main metallic composition of the Z phase around the {delta}-ferrite was the same as that in the other areas. There was no large difference in the size distribution of the Z phase among the steels. The mean diameter of the Z phases for T122 with {delta}-ferrite was relatively large in spite of a shorter creep exposure in contrast with T91 and T92. The number density of the Z phases increased with increasing creep exposure time except in the case of T91. The order of the number density was T122 with {delta}-ferrite, T91, T122 without {delta}-ferrite, and T92. In crept samples, the amount of Z phase in the gauge portion was higher than that in the grip portion, meaning that stress and/or strain promotes the formation of a Z phase during creep exposure. (orig.)

  1. Studies on Creep Deformation and Rupture Behavior of 316LN SS Multi-Pass Weld Joints Fabricated with Two Different Electrode Sizes

    Science.gov (United States)

    Vijayanand, V. D.; Kumar, J. Ganesh; Parida, P. K.; Ganesan, V.; Laha, K.

    2017-02-01

    Effect of electrode size on creep deformation and rupture behavior has been assessed by carrying out creep tests at 923 K (650 °C) over the stress range 140 to 225 MPa on 316LN stainless steel weld joints fabricated employing 2.5 and 4 mm diameter electrodes. The multi-pass welding technique not only changes the morphology of delta ferrite from vermicular to globular in the previous weld bead region near to the weld bead interface, but also subjects the region to thermo-mechanical heat treatment to generate appreciable strength gradient. Electron backscatter diffraction analysis revealed significant localized strain gradients in regions adjoining the weld pass interface for the joint fabricated with large electrode size. Larger electrode diameter joint exhibited higher creep rupture strength than the smaller diameter electrode joint. However, both the joints had lower creep rupture strength than the base metal. Failure in the joints was associated with microstructural instability in the fusion zone, and the vermicular delta ferrite zone was more prone to creep cavitation. Larger electrode diameter joint was found to be more resistant to failure caused by creep cavitation than the smaller diameter electrode joint. This has been attributed to the larger strength gradient between the beads and significant separation between the cavity prone vermicular delta ferrite zones which hindered the cavity growth. Close proximity of cavitated zones in smaller electrode joint facilitated their faster coalescence leading to more reduction in creep rupture strength. Failure location in the joints was found to depend on the electrode size and applied stress. The change in failure location has been assessed on performing finite element analysis of stress distribution across the joint on incorporating tensile and creep strengths of different constituents of joints, estimated by ball indentation and impression creep testing techniques.

  2. Creep behavior and in-depth microstructural characterization of dissimilar joints

    Directory of Open Access Journals (Sweden)

    F Kauffmann, T Klein, A Klenk and K Maile

    2013-01-01

    Full Text Available The 700 °C power plants currently under development will utilize Ni-base alloys such as alloy 617 for components to be operated at temperatures >650 °C. Due to economic reasons for components or parts of components which are subjected to temperatures <650 °C, 2% Cr or 9–12% Cr steels is used, depending on the required mechanical properties. This makes the dissimilar joining of Ni-base alloys and Cr steels a necessity in these plants. Experimental investigations show that these joints have to be identified as weak points with regard to damage development under creep and creep-fatigue loading. The present investigation focuses on welds between the alloy 617 and 2% Cr steel. Under creep load the fracture occurs near the fusion line between the 2% Cr steel base metal and alloy 617 weld metal. To explain the reasons for this fracture location, the microstructure of this fusion line was investigated using TEM and FIB techniques after welding and after creep loading. The TEM investigations have shown a small zone in the weld metal near the fusion line exhibiting chromium depletion and clearly reduced amounts of chromium carbides, leading to a weakening of this zone.

  3. Creep behavior and in-depth microstructural characterization of dissimilar joints

    Science.gov (United States)

    Kauffmann, F.; Klein, T.; Klenk, A.; Maile, K.

    2013-02-01

    The 700 °C power plants currently under development will utilize Ni-base alloys such as alloy 617 for components to be operated at temperatures >650 °C. Due to economic reasons for components or parts of components which are subjected to temperatures steels is used, depending on the required mechanical properties. This makes the dissimilar joining of Ni-base alloys and Cr steels a necessity in these plants. Experimental investigations show that these joints have to be identified as weak points with regard to damage development under creep and creep-fatigue loading. The present investigation focuses on welds between the alloy 617 and 2% Cr steel. Under creep load the fracture occurs near the fusion line between the 2% Cr steel base metal and alloy 617 weld metal. To explain the reasons for this fracture location, the microstructure of this fusion line was investigated using TEM and FIB techniques after welding and after creep loading. The TEM investigations have shown a small zone in the weld metal near the fusion line exhibiting chromium depletion and clearly reduced amounts of chromium carbides, leading to a weakening of this zone.

  4. Nanoindentation creep behavior in a CoCrFeCuNi high-entropy alloy film with two different structure states

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Y.; Peng, G.J.; Wen, D.H.; Zhang, T.H., E-mail: zhangth@zjut.edu.cn

    2015-01-05

    A CoCrFeCuNi high-entropy alloy (HEA) film, with thickness of about 1450 nm, was prepared by magnetron sputtering using alloy target. The structure of HEA film was fully relaxed by annealing at temperature of 800 K for one hour. The atomic lattice structures and morphologies of the surface and cross-section were detected in both as-deposited and annealed films by X-ray diffraction (XRD) and scanning electron microscope (SEM), respectively. The results indicate that a simple face-centered cubic (fcc) structure in the as-deposited film and the structure configuration in the annealed one was strongly changed, even a tiny but non-ignorable body-centered cubic (bcc) structure emerged. Furthermore, the creep behaviors of both samples were systematically studied by nanoindentation with a spherical tip. The sample's ability to resist both instantaneous and time-dependent plastic deformation was weakened after annealing. The creep behaviors of both cases were promoted at higher loads. Meanwhile, the effect of loading rate on the steady-state creep was more complicated: creep rate was accelerated in the as-deposited film with the loading rate, however it showed an opponent variation trend in the annealed one. Moreover, strain rate sensitivity was calculated from the steady-state creep and the creep deformation mechanism was discussed.

  5. Effect of Tungsten on Long-Term Microstructural Evolution and Impression Creep Behavior of 9Cr Reduced Activation Ferritic/Martensitic Steel

    Science.gov (United States)

    Thomas Paul, V.; Vijayanand, V. D.; Sudha, C.; Saroja, S.

    2017-01-01

    The present study describes the changes in the creep properties associated with microstructural evolution during thermal exposures to near service temperatures in indigenously developed reduced activation ferritic-martensitic steels with varying tungsten (1 and 1.4 wt pct W) contents. The creep behavior has been studied employing impression creep (IC) test, and the changes in impression creep behavior with tungsten content have been correlated with the observed microstructures. The results of IC test showed that an increase in 0.4 pct W decreases the creep rate to nearly half the value. Creep strength of 1.4 pct W steel showed an increase in steels aged for short durations which decreased as aging time increased. The microstructural changes include coarsening of precipitates, reduction in dislocation density, changes in microchemistry, and formation of new phases. The formation of various phases and their volume fractions have been predicted using the JMatPro software for the two steels and validated by experimental methods. Detailed transmission electron microscopy analysis shows coarsening of precipitates and formation of a discontinuous network of Laves phase in 1.4 W steel aged for 10,000 hours at 823 K (550 °C) which is in agreement with the JMatPro simulation results.

  6. Effect of Tungsten on Long-Term Microstructural Evolution and Impression Creep Behavior of 9Cr Reduced Activation Ferritic/Martensitic Steel

    Science.gov (United States)

    Thomas Paul, V.; Vijayanand, V. D.; Sudha, C.; Saroja, S.

    2016-10-01

    The present study describes the changes in the creep properties associated with microstructural evolution during thermal exposures to near service temperatures in indigenously developed reduced activation ferritic-martensitic steels with varying tungsten (1 and 1.4 wt pct W) contents. The creep behavior has been studied employing impression creep (IC) test, and the changes in impression creep behavior with tungsten content have been correlated with the observed microstructures. The results of IC test showed that an increase in 0.4 pct W decreases the creep rate to nearly half the value. Creep strength of 1.4 pct W steel showed an increase in steels aged for short durations which decreased as aging time increased. The microstructural changes include coarsening of precipitates, reduction in dislocation density, changes in microchemistry, and formation of new phases. The formation of various phases and their volume fractions have been predicted using the JMatPro software for the two steels and validated by experimental methods. Detailed transmission electron microscopy analysis shows coarsening of precipitates and formation of a discontinuous network of Laves phase in 1.4 W steel aged for 10,000 hours at 823 K (550 °C) which is in agreement with the JMatPro simulation results.

  7. Irradiation Creep in Graphite

    Energy Technology Data Exchange (ETDEWEB)

    Ubic, Rick; Butt, Darryl; Windes, William

    2014-03-13

    An understanding of the underlying mechanisms of irradiation creep in graphite material is required to correctly interpret experimental data, explain micromechanical modeling results, and predict whole-core behavior. This project will focus on experimental microscopic data to demonstrate the mechanism of irradiation creep. High-resolution transmission electron microscopy should be able to image both the dislocations in graphite and the irradiation-induced interstitial clusters that pin those dislocations. The team will first prepare and characterize nanoscale samples of virgin nuclear graphite in a transmission electron microscope. Additional samples will be irradiated to varying degrees at the Advanced Test Reactor (ATR) facility and similarly characterized. Researchers will record microstructures and crystal defects and suggest a mechanism for irradiation creep based on the results. In addition, the purchase of a tensile holder for a transmission electron microscope will allow, for the first time, in situ observation of creep behavior on the microstructure and crystallographic defects.

  8. Vortex Depinning in YBa2Cu3O7 : Resistive Transition Identification of the Crossover from Flux-Creep to Flux-Flow Behavior

    NARCIS (Netherlands)

    Hebard, A.F.; Palstra, T.T.M.

    1989-01-01

    Analysis of resistive transitions of YBa2Cu3O7, crystals reveals a scaling behavior which identifies the vortex-depinning critical field Hcp, hence the crossover in behavior from flux creep to flux flow. The inferred Hcp for YBa2Cu3O7 crystals closely approximates the magnitude and temperature depen

  9. Effect of Concrete Age and Creep on the Behavior of Concrete-Filled Steel Tube Columns

    Directory of Open Access Journals (Sweden)

    HaiYang Wang

    2016-01-01

    Full Text Available The influence of concrete age and creep on the ultimate axial loading capacity of concrete-filled steel tube (CFST columns is experimentally and numerically investigated. After validation of numerical models, a parametric study is conducted and the results are used to formulate empirical formulas for predicting the ultimate axial load-bearing capacity of the columns. Formulas are also proposed for predicting both the composite creep and aging coefficients of the CFST columns, which consider the confinement action of steel tubes on concrete. Then, the proposed formulas are validated independently by comparing their predictions with existing test results performed by other researchers. The comparisons show that the empirical formulas have the potential to be used in the practical design of CFST columns.

  10. Influence of weld structure on cross-weld creep behavior in P23 steel

    Energy Technology Data Exchange (ETDEWEB)

    Allen, D.J.; Degnan, C.C. [E.ON Engineering (United Kingdom); Brett, S.J. [RWE npower (United Kingdom); Buchanan, L.W. [Doosan Babcock (United Kingdom)

    2010-07-01

    A thick section pipe weld in low alloy steel P23 has been characterised by cross-weld creep rupture testing at a range of stresses, together with all-weld-metal and parent material testing, under the auspices of the UK High Temperature Power Plant Forum. The results generally show that the weld metal can be weak when tested in the transverse (cross-weld) orientation, and can fail with limited overall ductility by cracking in the zone of refined weld metal beneath the fusion boundary of the superposed weld bead. However, one specimen showed a much superior performance, which could be understood in terms of its locally more creep resistant weld macrostructure. The implications for P23 performance and weld manufacture are discussed. (orig.)

  11. Biaxial Creep Specimen Fabrication

    Energy Technology Data Exchange (ETDEWEB)

    JL Bump; RF Luther

    2006-02-09

    This report documents the results of the weld development and abbreviated weld qualification efforts performed by Pacific Northwest National Laboratory (PNNL) for refractory metal and superalloy biaxial creep specimens. Biaxial creep specimens were to be assembled, electron beam welded, laser-seal welded, and pressurized at PNNL for both in-pile (JOYO reactor, O-arai, Japan) and out-of-pile creep testing. The objective of this test campaign was to evaluate the creep behavior of primary cladding and structural alloys under consideration for the Prometheus space reactor. PNNL successfully developed electron beam weld parameters for six of these materials prior to the termination of the Naval Reactors program effort to deliver a space reactor for Project Prometheus. These materials were FS-85, ASTAR-811C, T-111, Alloy 617, Haynes 230, and Nirnonic PE16. Early termination of the NR space program precluded the development of laser welding parameters for post-pressurization seal weldments.

  12. Buckling of Bucket Foundations

    DEFF Research Database (Denmark)

    Madsen, Søren; Andersen, Lars Vabbersgaard; Ibsen, Lars Bo

    2012-01-01

    In this paper, the risk of structural buckling during installation of large-diameter bucket foundations is addressed using numerical methods. Imperfect geometries are introduced based on the pre-buckling mode shapes from a linear Eigenvalue buckling analysis. Various imperfect geometries are intr...

  13. Creep behavior and wear resistance of Al 5083 based hybrid composites reinforced with carbon nanotubes (CNTs) and boron carbide (B{sub 4}C)

    Energy Technology Data Exchange (ETDEWEB)

    Alizadeh, Ali [Faculty of Materials & Manufacturing Processes, Malek-e-Ashtar University of Technology, Tehran (Iran, Islamic Republic of); Abdollahi, Alireza, E-mail: alirezaabdollahi1366@gmail.com [Faculty of Materials & Manufacturing Processes, Malek-e-Ashtar University of Technology, Tehran (Iran, Islamic Republic of); Biukani, Hootan [Faculty of Engineering, South Tehran Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of)

    2015-11-25

    In the current research, aluminum based hybrid composite reinforced with boron carbide (B{sub 4}C) and carbon nanotubes (CNTs) was produced by powder metallurgy method. creep behavior, wear resistance, surface roughness, and hardness of the samples were investigated. To prepare the samples, Al 5083 powder was milled with boron carbide particles and carbon nanotubes using planetary ball mill under argon atmosphere with ball-to-powder weight ratio of 10:1 for 5 h. Afterwards, the milled powders were formed by hot press process at 380{sup °}C and then were sintered at 585{sup °}C under argon atmosphere for 2 h. There was shown to be an increase in hardness values of composite with an increase in B{sub 4}C content. The micrograph of worn surfaces indicate a delamination mechanism due to the presence of CNTs and abrasion mechanism in composite containing 10 vol.%B{sub 4}C. Moreover, it was shown that increasing B{sub 4}C content increases the wear resistance by 3 times under a load of 20 N and 10 times under a load of 10 N compared to CNTs-reinforced composite. surface roughness of the composite containing 5 vol.%CNT has shown to be more than other samples. The results of creep test showed that adding carbon nanotubes increases creep rate of Al 5083 alloy; however, adding B{sub 4}C decreases its creep rate. - Highlights: • Al 5083/(CNTs + B{sub 4}C) hybrid composite was produced by powder metallurgy method. • Creep behavior, wear resistance, surface roughness, and Hardness of samples were investigated. • Addition of CNTs to Al 5083 matrix reduces alloy hardness, wear resistance and creep strength. • By addition of B{sub 4}C and composite hybridization, creep strength and wear resistance increased. • Surface roughness of Al-5 vol.%CNT has shown to be more than other samples.

  14. Effects of fuel particle size and fission-fragment-enhanced irradiation creep on the in-pile behavior in CERCER composite pellets

    Science.gov (United States)

    Zhao, Yunmei; Ding, Shurong; Zhang, Xunchao; Wang, Canglong; Yang, Lei

    2016-12-01

    The micro-scale finite element models for CERCER pellets with different-sized fuel particles are developed. With consideration of a grain-scale mechanistic irradiation swelling model in the fuel particles and the irradiation creep in the matrix, numerical simulations are performed to explore the effects of the particle size and the fission-fragment-enhanced irradiation creep on the thermo-mechanical behavior of CERCER pellets. The enhanced irradiation creep effect is applied in the 10 μm-thick fission fragment damage matrix layer surrounding the fuel particles. The obtained results indicate that (1) lower maximum temperature occurs in the cases with smaller-sized particles, and the effects of particle size on the mechanical behavior in pellets are intricate; (2) the first principal stress and radial axial stress remain compressive in the fission fragment damage layer at higher burnup, thus the mechanism of radial cracking found in the experiment can be better explained.

  15. Stochastic analysis of laminated composite plates on elastic foundation: The cases of post-buckling behavior and nonlinear free vibration

    Energy Technology Data Exchange (ETDEWEB)

    Singh, B.N., E-mail: bnsingh@aero.iitkgp.ernet.i [Department of Aerospace Engineering, IIT Kharagpur 721 302, West Bengal (India); Lal, Achchhe [Department of Mechanical Engineering, SVNIT, Surat 395007 (India)

    2010-10-15

    This study deals with the stochastic post-buckling and nonlinear free vibration analysis of a laminated composite plate resting on a two parameters Pasternak foundation with Winkler cubic nonlinearity having uncertain system properties. The system properties are modeled as basic random variables. A C{sup 0} nonlinear finite element formulation of the random problem based on higher-order shear deformation theory in the von Karman sense is presented. A direct iterative method in conjunction with a stochastic nonlinear finite element method proposed earlier by the authors is extended to analyze the effect of uncertainty in system properties on the post-buckling and nonlinear free vibration of the composite plates having Winler type of geometric nonlinearity. Mean as well as standard deviation of the responses have been obtained for various combinations of geometric parameters, foundation parameters, stacking sequences and boundary conditions and compared with those available in the literature and Monte Carlo simulation.

  16. Crack growth behavior under creep-fatigue conditions using compact and double edge notch tension-compression specimens

    Science.gov (United States)

    Narasimha Chary, Santosh Balaji

    inspection of fatigue surfaces, it has been found that that better alignment control procedures are needed to ensure symmetric crack fronts for the DEN(T-C) specimen. Creep-fatigue crack growth tests were conducted on 9Cr-1Mo (P91) steels at 625°C with various hold times. These tests were conducted using C(T) specimens under constant load amplitude conditions (tension-tension) and DEN(T-C) specimens under displacement like conditions (tension-compression). Crack growth data generated under creep-fatigue conditions using standard C(T) specimens correlated well with crack growth data generated using DEN(T-C) specimens. The crack growth rates per cycle increased significantly with increase in hold time when crack growth data were plotted with the cyclic stress intensity parameter, Delta-K. A transient behavior in the initial portion of da/dN versus Delta-K plots were observed for the hold time tests, as reported previously by several other researchers. It is shown for the C(T) specimens that the creep-fatigue interactions during crack growth for various hold times are represented better by the (Ct)avg parameter implying that the P91 steel behaves in a creep-ductile manner. Significant differences (factors of 2 to 5) were observed between the calculated values of (Ct)avg and those based on measured values of force-line deflection. It is also shown that there is a high risk of obtaining invalid data in longer hold time tests under force-control conditions. The usefulness of DEN(T-C) specimens for crack growth studies under displacement controlled conditions to combat ratcheting problems in tests conducted under load conditions is established. The tests conditions for the round-robin program on creep-fatigue crack growth testing in support of ASTM E-2760 are finalized. Further developments needed in creep-fatigue crack growth testing are also presented.

  17. Effect of Notches on Creep-Fatigue Behavior of a P/M Nickel-Based Superalloy

    Science.gov (United States)

    Telesman, Jack; Gabb, Timothy P.; Ghosn, Louis J.; Gayda, John, Jr.

    2015-01-01

    A study was performed to determine and model the effect of high temperature dwells on notched low cycle fatigue (NLCF) and notch stress rupture behavior of a fine grain LSHR powder metallurgy (PM) nickel-based superalloy. It was shown that a 90 second dwell applied at the minimum stress (min dwell) was considerably more detrimental to the NLCF lives than similar dwell applied at the maximum stress (max dwell). The short min dwell NLCF lives were shown to be caused by growth of small oxide blisters which caused preferential cracking when coupled with high concentrated notch root stresses. The cyclic max dwell notch tests failed mostly by a creep accumulation, not by fatigue, with the crack origin shifting internally to a substantial distance away from the notch root. The classical von Mises plastic flow model was unable to match the experimental results while the hydrostatic stress profile generated using the Drucker-Prager plasticity flow model was consistent with the experimental findings. The max dwell NLCF and notch stress rupture tests exhibited substantial creep notch strengthening. The triaxial Bridgman effective stress parameter was able to account for the notch strengthening by collapsing the notched and uniform gage geometry test data into a singular grouping.

  18. Effect of particle size and temperature on rheology and creep behavior of barley β-d-glucan concentrate dough.

    Science.gov (United States)

    Ahmed, Jasim

    2014-10-13

    Concentrated β-D-glucan has been added in the formulation of food products development that attributing human health. The purpose of this study is to assess the role of particle size (74, 105, 149, 297 and 595 μm) of barley β-D-glucan concentrate (BGC) on two fundamental rheological properties namely oscillatory rheology and creep in a dough system (sample to water = 1:2). The water holding capacity, sediment volume fraction and protein content increased with an increase in particle size from 74 μm to 595 μm, which directly influences the mechanical strength and visco-elasticity of the dough. The dough exhibited predominating solid-like behavior (elastic modulus, G'>viscous modulus, G"). The G' decreased systematically with increasing temperature from 25 to 85 °C at the frequency range of 0.1-10 Hz except for the dough having particle size of 105 μm, which could be associated with increase in protein content in the fraction. A discrete retardation spectrum is employed to the creep data to obtain retardation time and compliance parameters which varied significantly with particle size and the process temperature. All those information could be helpful to identify the particle size range of BGC that could be useful to produce a β-D-glucan enriched designed food.

  19. Study on buckling and plastic collapse behavior of a continuous stiffened plate subjected to in-plane compression loads; Mennai asshuku kaju wo ukeru renzoku bodo panel no zakutsu sosei hokai kyodo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yao, T.; Fujikubo, M.; Yanagihara, D. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1996-04-10

    A hull structure is constituted by thin panels, and reinforced longitudinally and laterally by stiffened members to increase the effectiveness of the structure. In order to attain findings on buckling and plastic collapse behavior of stiffened plates, this paper describes analysis of elasto-plastic large deflection by using the finite element method on thin stiffened plates having flat-bars and angle-bars. The analysis includes the case of an aspect ratio being 5.0 and the case to consider welding residual stress. Considerations were given on cross sectional shape, panel aspect ratio and effects of initial welding imperfections against the buckling and plastic collapse behavior of the stiffened plates. The angle-bars tend to cause secondary buckling more easily because it has greater bending and twisting rigidity, and stronger constraint against deflection than the flat-bars. When the aspect ratio is larger and the span is longer, the ultimate strength declines, and the withstand power after the ultimate strength decreases rapidly. Existence of the residual stress tends to make the secondary buckling occur more easily. The secondary buckling affects little the withstand power after the ultimate strength. 3 refs., 7 figs., 1 tab.

  20. Plastic Buckling of Cylindrical Shells Under Transverse Loading

    Institute of Scientific and Technical Information of China (English)

    ZHANG Chonghou; LIU Yansheng; Yoshiaki Goto

    2008-01-01

    Thick cylindrical shells under transverse loading exhibit an elephant foot buckling mode, whereas moderately thick cylindrical shells show a diamond buckling mode. There exists some intermediate geome- try at which the transition between buckling modes can take place. This behavior is significantly influenced by the radius-to-thickness ratio and the material yield strength, rather than the length-to-radius ratio and the axial force. This paper presents a critical value at which the transition of buckling modes occurs as a func- tion of the radius-to-thickness ratio and the material yield strength. The result shows that the circumferential wave number of the diamond buckling mode increases with decreasing wall thickness. The strain concentra- tion is also intensified for the diamond buckling modes compared with the elephant foot buckling modes.

  1. Anomalous steam oxidation behavior of a creep resistant martensitic 9 wt. % Cr steel

    Energy Technology Data Exchange (ETDEWEB)

    Agüero, Alina, E-mail: agueroba@inta.es [Instituto Nacional de Técnica Aeroespacial, Ctra. de Ajalvir Km 4, 28850 Torrejón de Ardoz (Spain); González, Vanessa [Instituto Nacional de Técnica Aeroespacial, Ctra. de Ajalvir Km 4, 28850 Torrejón de Ardoz (Spain); Mayr, Peter [Chair of Welding Engineering, Chemnitz University of Technology, Reichenhainer Str. 70, 09126 Chemnitz (Germany); Spiradek-Hahn, Krystina [Alloy Development Group, Montanuniversität Leoben, 8700 Leoben (Austria)

    2013-08-15

    The efficiency of thermal power plants is currently limited by the long-term creep strength and the steam oxidation resistance of the commercially available ferritic/martensitic steel grades. Higher operating pressures and temperatures are essential to increase efficiency but impose important requirements on the materials, from both the mechanical and chemical stability perspective. It has been shown that in general, a Cr wt. % higher than 9 is required for acceptable oxidation rates at 650 °C, but on the other hand such high Cr content is detrimental to the creep strength. Surprisingly, preliminary studies of an experimental 9 wt. % Cr martensitic steel, exhibited very low oxidation rates under flowing steam at 650 °C for exposure times exceeding 20,000 h. A metallographic investigation at different time intervals has been carried out. Moreover, scanning transmission electron microscopy (STEM) analysis of a ground sample exposed to steam for 10,000 h at 650 °C revealed the formation of a complex tri-layered protective oxide comprising a top and bottom Fe and Cr rich spinel layer with a magnetite intermediate layer on top of a very fine grained zone. - Highlights: • High steam oxidation resistant 9 wt. % Cr martensitic steel at 650 °C. • Multilayer thin protective Cr–Fe oxide. • Nano-grain sub-oxide metal zone.

  2. Creep-rupture behavior of 3Cr-3W-V bainitic steels

    Energy Technology Data Exchange (ETDEWEB)

    Klueh, R.L. [Oak Ridge National Laboratory, TN 37831-6138 (United States)]. E-mail: kluehrl@ornl.gov; Evans, N.D. [Oak Ridge National Laboratory, TN 37831-6138 (United States); Maziasz, P.J. [Oak Ridge National Laboratory, TN 37831-6138 (United States); Sikka, V.K. [Oak Ridge National Laboratory, TN 37831-6138 (United States)

    2007-01-15

    A nominally Fe-3.0Cr-3.0W-0.25 V (3Cr-3WV) steel and this composition with 0.07% Ta (3Cr-3WVTa) were developed for elevated-temperature service in the power-generation and petrochemical industries. Creep-rupture strengths of the new steels to 600 deg. C exceeded those of the two advanced commercial 2.25Cr steels T23 (Fe-2.25Cr-1.6W-0.25V-0.05Nb-0.07C) and T24 (Fe-2.25Cr-1.0Mo-0.25V-0.07Ti-0.005B-0.07C). Moreover, the strength of 3Cr-3WVTa approached that of modified 9Cr-1Mo (T91) at 650 deg. C. Elevated-temperature strength in the new steels is obtained from a bainitic microstructure with a high number density of fine needle-like MX precipitates in the matrix. The presence of tantalum promotes a finer MX precipitate in the 3Cr-3WVTa than in the 3Cr-3WV, and it suppresses the coarsening of these fine precipitates during creep.

  3. Creep-Rupture Behavior of Ni-Based Alloy Tube Bends for A-USC Boilers

    Science.gov (United States)

    Shingledecker, John

    Advanced ultrasupercritical (A-USC) boiler designs will require the use of nickel-based alloys for superheaters and reheaters and thus tube bending will be required. The American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code Section II PG-19 limits the amount of cold-strain for boiler tube bends for austenitic materials. In this summary and analysis of research conducted to date, a number of candidate nickel-based A-USC alloys were evaluated. These alloys include alloy 230, alloy 617, and Inconel 740/740H. Uniaxial creep and novel structural tests and corresponding post-test analysis, which included physical measurements, simplified analytical analysis, and detailed microscopy, showed that different damage mechanisms may operate based on test conditions, alloy, and cold-strain levels. Overall, creep strength and ductility were reduced in all the alloys, but the degree of degradation varied substantially. The results support the current cold-strain limits now incorporated in ASME for these alloys for long-term A-USC boiler service.

  4. Effects of Hf and B on high temperature low stress creep behavior of a second generation Ni-based single crystal superalloy DD11

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Y.S. [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China); Science and Technology on Advanced High Temperature Structural Materials Laboratory, Beijing Institute of Aeronautical Materials, Beijing 100095 (China); Zhang, J.; Luo, Y.S. [Science and Technology on Advanced High Temperature Structural Materials Laboratory, Beijing Institute of Aeronautical Materials, Beijing 100095 (China); Li, J. [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China); NCS Testing Technology Co., Ltd., Beijing 100081 (China); Tang, D.Z., E-mail: Dingzhongtang621@163.com [Science and Technology on Advanced High Temperature Structural Materials Laboratory, Beijing Institute of Aeronautical Materials, Beijing 100095 (China)

    2016-08-30

    The as-cast and heat-treated microstructures and high temperature creep properties have been investigated in four experimental Ni-based single crystal superalloys containing various levels of Hf addition (0–0.4 wt%) and B addition (0–0.02 wt%). The experimental results indicated that the creep rupture life showed an improvement with individual addition of Hf, but it was decreased with individual addition of B. The elemental partitioning ratio and interfacial dislocation spacing of γ/γ′ were obviously changed with individual Hf or B additions. Meanwhile, the formation of secondary phases, such as the blocky MC carbide, script-like shape M{sub 3}B{sub 2} phases, was observed in the creep samples, which was also closely related to the high temperature creep behaviors. The high volume fraction of residual (γ+γ′) eutectics was mainly attributed to the significant decrease of creep rupture life for the present experimental alloy containing both Hf and B additions. This study is helpful to better understand Hf and B's role of strengthening mechanism and to optimize Hf and B additions in single crystal superalloys.

  5. Creep-rupture behavior of candidate Stirling engine alloys after long-term aging at 760 deg C in low-pressure hydrogen

    Science.gov (United States)

    Titran, R. H.

    1984-01-01

    Nine candidate Stirling automotive engine alloys were aged at 760 C for 3500 hr in low pressure hydrogen or argon to determine the resulting effects on mechanical behavior. Candidate heater head tube alloys were CG-27, W545, 12RN72, INCONEL-718, and HS-188 while candidate cast cylinder-regenerator housing alloys were SA-F11, CRM-6D, XF-818, and HS-31. Aging per se is detrimental to the creep rupture and tensile strengths of the iron base alloys. The presence of hydrogen does not significantly contribute to strength degradation. Based percent highway driving cycle; CG-27 has adequate 3500 hr - 870 C creep rupture strength and SA-Fll, CRM-6D, and XF-818 have adequate 3500 hr - 775 C creep rupture strength.

  6. Study of creep behavior of a calcarenite: San Julián´s stone (Alicante

    Directory of Open Access Journals (Sweden)

    Brotóns, V.

    2013-12-01

    Full Text Available Rocks creep has a great importance in the evaluation of the long-term behaviour of elements built with or within these materials. In this work, a porous well-known limestone locally named as San Julián stone has been physically and mechanically characterized. Uniaxial compressive tests for 96 h. at constant stress are carried out. Long-term behaviour has been modelled by means of a well-known creep model, the CEB-FIP Model code 2010, used for modelling other stony-material (i.e. concrete. Furthermore, a rheological model has been proposed. The main aim of this work is to investigate the possibility of exploiting the vast experience accumulated in the study of concrete deformational long-term behaviour in order to obtaining a reasonable approach to the behaviour of the rock, for too long testing times difficult to implement in laboratory. A creep function adapted to the studied rock only dependent on its elastic and mechanical characteristics is also proposed in this work.La fluencia de las rocas tiene gran importancia en la evaluación del comportamiento a largo plazo de elementos construidos con estos materiales. En este trabajo, se ha caracterizado física y mecánicamente una calcarenita porosa bien conocida localmente como Piedra de San Julián. Se han realizado ensayos de compresión uniaxial de 96 h. a carga constante. Se ha utilizado un modelo de fluencia bien conocido, el Código-modelo CEB-FIP 2010, usado para modelizar otro material pétreo (hormigón. Además, se ha propuesto un modelo reológico. El objetivo principal de este trabajo es investigar la posibilidad de aprovechar la gran experiencia acumulada en el estudio del hormigón, con el fin de obtener un enfoque para el comportamiento de la roca, para tiempos de prueba muy largos difíciles de implementar en laboratorio. Se propone una función de fluencia adaptada a la roca estudiada dependiente sólo de sus características elásticas y mecánicas.

  7. An high order Mixed Interpolation Tensorial Components (MITC) shell element approach for modeling the buckling behavior of delaminated composites

    DEFF Research Database (Denmark)

    Gaiotti, Marco; Rizzo, Cesare M.; Branner, Kim

    2014-01-01

    of composite laminates of wind turbine blades, results were found valuable for the marine industry as well, because similar laminates are used for the hull shell and stiffeners. Systematic calculations were carried out to assess the effects of an embedded delamination on the buckling load, varying the size...... and through thickness position of the delamination. Different finite element modeling strategies were considered and validated against the experimental results. The one applying the 9 nodes MITC shell elements was found matching the experimental data despite failure modes were different for the two...

  8. Micromechanics of collective buckling in CNT turfs

    Science.gov (United States)

    Torabi, Hamid; Radhakrishnan, Harish; Mesarovic, Sinisa Dj.

    2014-12-01

    Complex structures consisting of intertwined, nominally vertical carbon nanotubes (CNTs) are called turfs. Under uniform compression experiments, CNT turfs exhibit irreversible collective buckling of a layer preceded by reorientation of CNT segments. Experimentally observed independence of the buckling stress and the buckling wavelength on the turf width suggests the existence of an intrinsic material length. To investigate the relationship the macroscopic material properties and the statistical parameters describing the nano-scale geometry of the turf (tortuosity, density and connectivity) we develop a nano-scale computational model, based on the representation of CNT segments as elastica finite elements with van der Waals interactions. The virtual turfs are generated by means of a constrained random walk algorithm and subsequent relaxation. The resulting computational model is robust and is capable of modeling the collective behavior of CNTs. We first establish the dependence of statistical parameters on the computational parameters used for turf generation, then establish relationships between post-buckling stress, initial elastic modulus and buckling wavelength on statistical turf parameters. Finally, we analyze the reorientation of buckling planes of individual CNTs during the collective buckling process.

  9. Study of creep-fatigue behavior in a 1000 MW rotor using a phenomenological lifetime model

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Nailong; Wang, Weizhe; Jiang, Jishen; Liu, Yingzheng [School of Mechanical Engineering, Shanghai (China)

    2017-02-15

    In this study, the phenomenological lifetime model was applied to part of an ultra-supercritical steam turbine rotor model to predict its lifetime as a post processing of the finite element method. To validate the accuracy and adaptation of the post processing program, stress strain hysteresis loops of a cylinderal model under service-like load cycle conditions in cycle N = 1 and 300 were constructed, and the comparison of the results with experimental data on the same cylinderal specimen showed them to be satisfactory. The temperature and von Mises stress distributions of the rotor during a startup-running-shutdown-natural cool process were numerically studied using ABAQUS and the damage caused by the interaction of creep and fatigue was subsequently computed and discussed. It was found that the maximum damage appeared at the inlet notch zone, with the blade groove areas and the front notch areas also suffering a large damage amplitude.

  10. On The Creep Behavior and Deformation Mechanisms Found in an Advanced Polycrystalline Nickel-Base Superalloy at High Temperatures

    Science.gov (United States)

    Deutchman, Hallee Zox

    Polycrystalline Ni-base superalloys are used as turbine disks in the hot section in jet engines, placing them in a high temperature and stress environment. As operating temperatures increase in search of better fuel efficiency, it becomes important to understand how these higher temperatures are affecting mechanical behavior and active deformation mechanisms in the substructure. Not only are operating temperatures increasing, but there is a drive to design next generation alloys in shorter time periods using predictive modeling capabilities. This dissertation focuses on mechanical behavior and active deformation mechanisms found in two different advanced polycrystalline alloy systems, information which will then be used to build advanced predictive models to design the next generation of alloys. The first part of this dissertation discusses the creep behavior and identifying active deformation mechanisms in an advanced polycrystalline Ni-based superalloy (ME3) that is currently in operation, but at higher temperatures and stresses than are experienced in current engines. Monotonic creep tests were run at 700°C and between 655-793MPa at 34MPa increments, on two microstructures (called M1 and M2) produced by different heat treatments. All tests were crept to 0.5% plastic strain. Transient temperature and transient stress tests were used determine activation energy and stress exponents of the M1 microstructure. Constant strain rate tests (at 10-4s-1) were performed on both microstructures as well. Following creep testing, both M1 and M2 microstructures were fully characterized using Scanning Electron Microscopy (SEM) for basic microstructure information, and Scanning Transmission Electron Microscopy (STEM) to determine active deformation mechanism. It was found that in the M1 microstructure, reorder mediated activity (such as discontinuous faulting and microtwinning) is dominant at low stresses (655-724 MPa). Dislocations in the gamma matrix, and overall planar

  11. DETERMINATION OF CREEP PROPERTIES OF THERMAL BARRIER COATING(TBC) SYSTEMS FROM THE INDENTATION CREEP TESTING WITH ROUND FLAT INDENTERS

    Institute of Scientific and Technical Information of China (English)

    B. Zhao; B.X. Xu; J. Liu; Z.F. Yue

    2004-01-01

    Indentation creep behavior with cylindrical flat indenters on the thermal barrier coating (TBC) was studied by finite element method (FEM). On the constant applied indentation creep stress, there is a steady creep rate for each case studied for different creep properties of the TBC system. The steady creep depth rate depends on the applied indentation creep stress and size of the indenters as well as the creep properties of the bond coat of the TBC and the substrate. The possibilities to determine the creep properties of a thermal barrier system from indention creep testing were discussed. As an example, with two different size indenters, the creep properties of bond coat of the TBC system can be derived by an inverse FEM method. This study not only provides a numerical method to obtain the creep properties of the TBC system, but also extends the application of indentation creep method with cylindrical flat indenters.

  12. Development of an accurate molecular mechanics model for buckling behavior of multi-walled carbon nanotubes under axial compression.

    Science.gov (United States)

    Safaei, B; Naseradinmousavi, P; Rahmani, A

    2016-04-01

    In the present paper, an analytical solution based on a molecular mechanics model is developed to evaluate the elastic critical axial buckling strain of chiral multi-walled carbon nanotubes (MWCNTs). To this end, the total potential energy of the system is calculated with the consideration of the both bond stretching and bond angular variations. Density functional theory (DFT) in the form of generalized gradient approximation (GGA) is implemented to evaluate force constants used in the molecular mechanics model. After that, based on the principle of molecular mechanics, explicit expressions are proposed to obtain elastic surface Young's modulus and Poisson's ratio of the single-walled carbon nanotubes corresponding to different types of chirality. Selected numerical results are presented to indicate the influence of the type of chirality, tube diameter, and number of tube walls in detailed. An excellent agreement is found between the present numerical results and those found in the literature which confirms the validity as well as the accuracy of the present closed-form solution. It is found that the value of critical axial buckling strain exhibit significant dependency on the type of chirality and number of tube walls. Copyright © 2016. Published by Elsevier Inc.

  13. Uniaxial creep behavior of nanostructured, solution and dispersion hardened V-1.4Y-7W-9Mo-0.7TiC with different grain sizes

    Energy Technology Data Exchange (ETDEWEB)

    Sakamoto, T. [Department of Materials Science and Biotechnology, Ehime University, 3 Bunkyo-cho, Matsuyama 790-8577 (Japan); Kurishita, H., E-mail: kurishi@imr.tohoku.ac.jp [International Research Center for Nuclear Materials Science, Institute for Materials Research, Tohoku University, Oarai, Ibaraki 311-1313 (Japan); Furuno, T. [Department of Materials Science and Biotechnology, Ehime University, 3 Bunkyo-cho, Matsuyama 790-8577 (Japan); Nagasaka, T. [Fusion Engineering Research Center, National Institute for Fusion Science (NIFS), Oroshi-cho 322-6, Toki, Gifu 292 (Japan); Kobayashi, S.; Nakai, K. [Department of Materials Science and Biotechnology, Ehime University, 3 Bunkyo-cho, Matsuyama 790-8577 (Japan); Matsuo, S.; Arakawa, H. [International Research Center for Nuclear Materials Science, Institute for Materials Research, Tohoku University, Oarai, Ibaraki 311-1313 (Japan); Nishimura, A.; Muroga, T. [Fusion Engineering Research Center, National Institute for Fusion Science (NIFS), Oroshi-cho 322-6, Toki, Gifu 292 (Japan)

    2011-10-15

    Highlights: {yields} The major concern for nanostructured V is poor creep resistance due to grain boundary sliding. {yields} Significant enhancement of creep resistance in nanostructured V has been achieved using V-1.4Y-7W-9Mo-0.7TiC. {yields} The enhancement owes to solute W and Mo, dispersoids of Y{sub 2}O{sub 3} and TiC and grain size (GS) adjustment. {yields} The creep life of V-1.4Y-7W-9Mo-0.7TiC increases by a factor 30 by increasing GS from 0.6 to 2.2 {mu}m. {yields} The creep life for 2.2 {mu}m GS is two orders longer than that of primary candidate V-4Cr-4Ti (GS: {approx}18 {mu}m). - Abstract: Nanostructured vanadium (V) alloys are expected to exhibit high performance under neutron irradiation environments. However, their ultra-fine or refined grains cause significant decrease in flow stress at high temperatures due to grain boundary sliding (GBS), which is the major concern for their high-temperature structural applications such as future fusion reactors. The contribution of GBS to plastic deformation is known to depend strongly on grain size (GS) and may give more significant influence on long-time creep test results than on short-time tensile test results. In order to improve the creep resistance through elucidation of the effect of GS on the uniaxial creep behavior of nanostructured V alloys, a solution and dispersion hardened V alloy, V-1.4Y-7W-9Mo-0.7TiC (in wt%), with GSs from 0.58 to 2.16 {mu}m was developed by mechanical alloying and HIP processes, followed by annealing at 1473-1773 K, and creep tested at 1073 K and 250 MPa in vacuum. It is shown that the creep resistance of V-1.4Y-7W-9Mo-0.7TiC increases monotonically with GS: The creep life for the alloy with 2.16 {mu}m in GS is as long as 114 h, which is longer by factors of 2-30 than those for the other finer grained alloys and by two orders than that for coarse-grained V-4Cr-4Ti (Nifs heat2, GS: 17.8 {mu}m) that is a primary candidate material for fusion reactor structural applications. The

  14. Comparison of Bending Creep Behavior of Bamboo-based Composites Manufactured by Two Types of Stacking Sequences

    OpenAIRE

    Xinxin Ma; Ge Wang; Zehui Jiang; Yu Xian; Haidong Li

    2014-01-01

    The study of viscoelastic and mechano-sorptive creep on bamboo laminated veneer lumber (BLVL) and bamboo/poplar plywood (BPP) is described in this paper. Bending creep tests parallel to the grain were carried out on two bamboo-based composites for a length of 90 days. The specimens measured 500 mm × 20 mm × 12 mm. Based on the experimental data, the creep curves of two boards were evaluated. The results are summarized as follows: (1) the anti-creep property of BLVL was better than that of BPP...

  15. Seismic Creep

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Seismic creep is the constant or periodic movement on a fault as contrasted with the sudden erupture associated with an earthquake. It is a usually slow deformation...

  16. Creeping eruption

    Science.gov (United States)

    ... are infected. Symptoms Symptoms of creeping eruption include: Blisters Itching , may be more severe at night Raised, ... enter the body through bare feet, so wearing shoes in areas where hookworm infestations are known to ...

  17. Numerical analysis of the creeping behavior of the S. Andrea di Perarolo secondary landslide (Italian Eastern Alps)

    Science.gov (United States)

    Cioli, C.; Genevois, R.; Iafelice, M.; Zorzi, L.

    2012-04-01

    The S. Andrea landslide is a complex secondary phenomenon characterized by continuous movements causing a very high hazard condition for the near Perarolo di Cadore village (Italian Eastern Alps). A significant amount of geological and geotechnical investigations has been carried out in the past allowing the detection of the basal sliding surface. In specific, the sliding surface coincides with the contact between the bedrock and the overlying mass of an old landslides, involving a volume of about 180.000 cubic meters. A numerical approach has been adopted to analyze the stability of slope. This method is able to simulate the formation and development of shear zones as areas of strain localization in the model. Indeed, the S. Andrea landslide has been, then, investigated using FLAC, a two-dimensional explicit finite difference program, particularly useful in case of slopes with complex geometry. In order to build up a suitable model, variation of geological, hydrogeological and geotechnical parameters have been identified from the interpretation of all available data. In a preliminary stage, a Mohr-Coulomb plasticity model has been adopted except for the bedrock, which was characterized by an isotropic elastic model. Groundwater flow condition has been performed evaluating the change in pore pressure coupled to the mechanical deformation calculation. Numerical results show that this model cannot simulate real displacement behavior of the slope mainly due to both the complex material behavior and lithological heterogeneity, and due to geotechnical spatial complexity of different soils and mechanical parameters. It has been assumed that it was necessary to improve the model in the light of a time dependent behavior of existing soils. An elastic-viscoplastic model has been then used to reproduce the observed creeping behavior, and only in viscoplastic region time effects have been considered. Discussion of results points out on: i) the evolution of the ``mechanical

  18. Creep rupture behavior of 9Cr–1.8W–0.5Mo–VNb (ASME grade 92) ferritic steel weld joint

    Energy Technology Data Exchange (ETDEWEB)

    Sakthivel, T., E-mail: tsakthivel@igcar.gov.in; Vasudevan, M.; Laha, K., E-mail: laha@igcar.gov.in; Parameswaran, P.; Chandravathi, K.S.; Panneer Selvi, S.; Maduraimuthu, V.; Mathew, M.D.

    2014-01-03

    Creep rupture behavior of 9Cr–1.8W–0.5Mo–VNb (ASME grade 92) ferritic steel weld joint fabricated by activated TIG (A-TIG) welding process have been investigated at 923 K over a stress range of 80–150 MPa. The weld joint was comprise of fusion zone, heat affected zone (HAZ) and base metal. The HAZ consisted of coarse prior-austenite grain (CGHAZ), fine prior-austenite grain (FGHAZ) and intercritical (ICHAZ) regions in an order away from the fusion zone to base metal. A hardness trough was observed at the outer edge of HAZ of the weld joint. TEM investigation revealed the presence of coarse M{sub 23}C{sub 6} precipitates and recovery of martensite lath structure into subgrain in the ICHAZ of the weld joint, leading to the hardness trough. The weld joint exhibited lower creep rupture lives than the base metal at relatively lower stresses. Creep rupture failure location of the weld joint was found to shift with applied stress. At high stresses fracture occurred in the base metal, whereas failure location shifted to FGHAZ at lower stresses with significant decrease in rupture ductility. SEM investigation of the creep ruptured specimens revealed precipitation of Laves phase across the joint, more extensively in the FGHAZ. On creep exposure, the hardness trough was found to shift from the ICHAZ to FGHAZ. Extensive creep cavitation was observed in the FGHAZ and was accompanied with the Laves phase, leading to the premature type IV failure of the steel weld joint at the FGHAZ.

  19. Impression creep technique-An overview

    Energy Technology Data Exchange (ETDEWEB)

    Sastry, D.H. [Department of Metallurgy, Indian Institute of Science, Bangalore (India)]. E-mail: dhsastry@hotmail.com

    2005-11-15

    Impression creep technique is a modified indentation creep test wherein the conical or ball indenter is replaced by a cylindrical, flat bottomed punch. The usefulness of this technique, pioneered by Prof. Li, is illustrated by application to a variety of problems in this laboratory. High temperature creep behavior of a number of metals and alloys, particularly estimation of the thermal activation parameters aiding the identification of the rate controlling mechanisms of creep, has been investigated. The technique has also been exploited to assess the 'single crystal' creep behavior vis a vis that of a polycrystalline sample. Utilizing the impression creep test, the creep behavior of individual zones in steel weldments has been examined. The simplicity and the utility of the impression creep test have been further demonstrated by its application to the study of superplastic behavior in alloys. This paper presents a cross section of the results obtained in the above investigations. It is concluded that the impression creep test technique is capable of yielding much of the information that can be obtained from tensile creep testing. Furthermore, it can provide data which are either impossible or extremely difficult to obtain with conventional creep testing.

  20. Experimental research on the creep behavior and bearing capacity of repeatedly prestressed concrete beam

    Institute of Scientific and Technical Information of China (English)

    SHAO Xudong; LI Lifeng; YANG Jianjun

    2007-01-01

    In the prestress tensioning process of medium or short span prestressed concrete beam bridges,there are always many serious problems,such as the camber of straight beam being too large,curved beam going crosswise,and columns of rigid beam bridge cracking,that can be commonly seen because of its greater additional stress in prestressing.To solve the above problems,a new concept of repeatedly prestressed bridge structure was innovatively proposed in this work.It was proved,through theoretical and experimental comparison between this new structure and the traditional prestressed structure,that the application of repeated prestressing technology can greatly improve the mechanical and deformational performance of the low height beam during construction and long-term use.Furthermore,a kind of computational formula to calculate creep strain and deformation due to repeated prestressing in terms of time t was derived in this paper and the bearing capacity of this new structure has been tested.Finally,the work concludes that there is a bright application prospect for this new structure for medium and short span prestressed beam bridges to control deformations.

  1. Deterministic and Probabilistic Creep and Creep Rupture Enhancement to CARES/Creep: Multiaxial Creep Life Prediction of Ceramic Structures Using Continuum Damage Mechanics and the Finite Element Method

    Science.gov (United States)

    Jadaan, Osama M.; Powers, Lynn M.; Gyekenyesi, John P.

    1998-01-01

    High temperature and long duration applications of monolithic ceramics can place their failure mode in the creep rupture regime. A previous model advanced by the authors described a methodology by which the creep rupture life of a loaded component can be predicted. That model was based on the life fraction damage accumulation rule in association with the modified Monkman-Grant creep ripture criterion However, that model did not take into account the deteriorating state of the material due to creep damage (e.g., cavitation) as time elapsed. In addition, the material creep parameters used in that life prediction methodology, were based on uniaxial creep curves displaying primary and secondary creep behavior, with no tertiary regime. The objective of this paper is to present a creep life prediction methodology based on a modified form of the Kachanov-Rabotnov continuum damage mechanics (CDM) theory. In this theory, the uniaxial creep rate is described in terms of stress, temperature, time, and the current state of material damage. This scalar damage state parameter is basically an abstract measure of the current state of material damage due to creep deformation. The damage rate is assumed to vary with stress, temperature, time, and the current state of damage itself. Multiaxial creep and creep rupture formulations of the CDM approach are presented in this paper. Parameter estimation methodologies based on nonlinear regression analysis are also described for both, isothermal constant stress states and anisothermal variable stress conditions This creep life prediction methodology was preliminarily added to the integrated design code CARES/Creep (Ceramics Analysis and Reliability Evaluation of Structures/Creep), which is a postprocessor program to commercially available finite element analysis (FEA) packages. Two examples, showing comparisons between experimental and predicted creep lives of ceramic specimens, are used to demonstrate the viability of this methodology and

  2. Buckling of Ship Structures

    CERN Document Server

    Shama, Mohamed

    2013-01-01

    Buckling of Ship Structures presents a comprehensive analysis of the buckling problem of ship structural members. A full analysis of the various types of loadings and stresses imposed on ship plating and primary and secondary structural members is given. The main causes and consequences of the buckling mode of failure of ship structure and the methods commonly used to control buckling failure are clarified. This book contains the main equations required to determine the critical buckling stresses for both ship plating and the primary and secondary stiffening structural members. The critical buckling stresses are given for ship plating subjected to the induced various types of loadings and having the most common boundary conditions encountered in ship structures.  The text bridges the gap existing in most books covering the subject of buckling of ship structures in the classical analytical format, by putting the emphasis on the practical methods required to ensure safety against buckling of ship structur...

  3. The influence of Mg on creep properties and fracture behaviors of Mar-M247 superalloy under 1255 K/200 MPa

    Science.gov (United States)

    Bor, H. Y.; Ma, C. Y.; Chao, C. G.

    2000-05-01

    The effects of Mg microadditions on the high-temperature/low stress (1255 K/200 MPa) creep properties and fracture behavior of a Mar-M247 superalloy were investigated in this study. The results of quantitative statistical analyses showed that when Mg microadditions up to 50 ppm were made, the MC carbides located at grain boundaries (designated GB MC) were significantly refined and spheroidized and the number of MC carbides decreased. In addition, the M23C6 carbides present on GBs dramatically increased with increasing Mg contents up to 50 ppm, and the creep resistance was enhanced under the test condition of 1255 K/200 MPa. However, the creep performance of a Mar-M247 superalloy containing 80 ppm Mg deteriorated due to the formation of an extremely large amount of MC carbide and a decrease in the number of M23C6 carbides at GBs. The cracks mainly initiated and propagated along GBs in both the Mg-free and Mg-containing Mar-M247 superalloys under 1255 K/200 MPa, and the finial rupture was caused by intergranular fracture. Under the present creep condition, the optimal Mg microaddition to a Mar-M247 superalloy should be 30 to 50 ppm.

  4. Voltage-Induced Buckling of Dielectric Films using Fluid Electrodes

    CERN Document Server

    Tavakol, Behrouz

    2016-01-01

    Accurate and integrable control of different flows within microfluidic channels is crucial to further development of lab-on-a-chip and fully integrated adaptable structures. Here we introduce a flexible microactuator that buckles at a high deformation rate and alters the downstream fluid flow. The microactuator consists of a confined, thin, dielectric film that buckles into the microfluidic channel when exposed to voltage supplied through conductive fluid electrodes. We estimate the critical buckling voltage, and characterize the buckled shape of the actuator. Finally, we investigate the effects of frequency, flow rate, and the pressure differences on the behavior of the buckling structure and the resulting fluid flow. These results demonstrate that the voltage--induced buckling of embedded microstructures using fluid electrodes provides a means for high speed attenuation of microfluidic flow.

  5. Small punch creep test in a 316 austenitic stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Saucedo-Munoz, M. L.; Komazaki, S. I.; Hashida, T.; Lopez-Hirata, V. M.

    2015-03-30

    The small punch creep test was applied to evaluate the creep behavior of a 316 type austenitic stainless steel at temperatures of 650, 675 and 700 degree centigrade. The small punch test was carried out using a creep tester with a specimen size of 10x10x0.3 mm at 650, 675 and 700 degree centigrade using loads from 199 to 512 N. The small punch creep curves show the three stages found in the creep curves of the conventional uniaxial test. The conventional creep relationships which involve parameters such as creep rate, stress, time to rupture and temperature were followed with the corresponding parameters of small punch creep test and they permitted to explain the creep behavior in this steel. The mechanism and activation energy of the deformation process were the grain boundary sliding and diffusion, respectively, during creep which caused the intergranular fracture in the tested specimens. (Author)

  6. Low-temperature creep of austenitic stainless steels

    Science.gov (United States)

    Reed, R. P.; Walsh, R. P.

    2017-09-01

    Plastic deformation under constant load (creep) in austenitic stainless steels has been measured at temperatures ranging from 4 K to room temperature. Low-temperature creep data taken from past and unreported austenitic stainless steel studies are analyzed and reviewed. Creep at cryogenic temperatures of common austenitic steels, such as AISI 304, 310 316, and nitrogen-strengthened steels, such as 304HN and 3116LN, are included. Analyses suggests that logarithmic creep (creep strain dependent on the log of test time) best describe austenitic stainless steel behavior in the secondary creep stage and that the slope of creep strain versus log time is dependent on the applied stress/yield strength ratio. The role of cold work, strain-induced martensitic transformations, and stacking fault energy on low-temperature creep behavior is discussed. The engineering significance of creep on cryogenic structures is discussed in terms of the total creep strain under constant load over their operational lifetime at allowable stress levels.

  7. Axisymmetric compressive buckling of multi-walled carbon nanotubes under different boundary conditions

    Institute of Scientific and Technical Information of China (English)

    Cheng-Qi Sun; Kai-Xin Liu; You-Shi Hong

    2012-01-01

    The paper studies the axisymmetric compressive buckling behavior of multi-walled carbon nanotubes (MWNTs) under different boundary conditions based on continuum mechanics model.A buckling condition is derived for determining the critical buckling load and associated buckling mode of MWNTs,and numerical results are worked out for MWNTs with different aspect ratios under fixed and simply supported boundary conditions.It is shown that the critical buckling load of MWNTs is insensitive to boundary conditions,except for nanotubes with smaller radii and very small aspect ratio.The associated buckling modes for different layers of MWNTs are in-phase,and the buckling displacement ratios for different layers are independent of the boundary conditions and the length of MWNTs.Moreover,for simply supported boundary conditions,the critical buckling load is compared with the corresponding one for axial compressive buckling,which indicates that the critical buckling load for axial compressive buckling can be well approximated by the corresponding one for axisymmetric compressive buckling.In particular,for axial compressive buckling of double-walled carbon nanotubes,an analytical expression is given for approximating the critical buckling load.The present investigation may be of some help in further understanding the mechanical properties of MWNTs.

  8. Oscillatory rheology and creep behavior of barley β-D-glucan concentrate dough: effect of particle size, temperature, and water content.

    Science.gov (United States)

    Ahmed, Jasim; Thomas, Linu; Al-Attar, Hasan

    2015-01-01

    Small amplitude oscillatory rheology and creep behavior of β-glucan concentrate (BGC) dough were studied as function of particle size (74, 105, 149, 297, and 595 μm), BGC particle-to-water ratio (1:4, 1:5, and 1:6), and temperature (25, 40, 55, 70, and 85 °C). The color intensity and protein content increased with decreasing particle size by creating more surface areas. The water holding capacity (WHC) and sediment volume fraction increased with increasing particle size from 74 to 595 μm, which directly influences the mechanical rigidity and viscoelasticity of the dough. The dough exhibited predominating solid-like behavior (elastic modulus, G' > viscous modulus, G″). A discrete retardation spectrum is employed to the creep data to obtain retardation time and compliance parameters, which varied significantly with particle size and the process temperature. Creep tests exhibited more pronounced effect on dough behavior compared to oscillatory measurement. The protein denaturation temperature was insignificantly increased with particle fractions from 107 to 110 °C. All those information could be helpful to identify the particle size range and WHC of BGC that could be useful to produce a β-d-glucan enriched designed food. © 2014 Institute of Food Technologists®

  9. 3D discrete dislocation dynamics study of creep behavior in Ni-base single crystal superalloys by a combined dislocation climb and vacancy diffusion model

    Science.gov (United States)

    Gao, Siwen; Fivel, Marc; Ma, Anxin; Hartmaier, Alexander

    2017-05-01

    A three-dimensional (3D) discrete dislocation dynamics (DDD) creep model is developed to investigate creep behavior under uniaxial tensile stress along the crystallographic [001] direction in Ni-base single crystal superalloys, which takes explicitly account of dislocation glide, climb and vacancy diffusion, but neglects phase transformation like rafting of γ‧ precipitates. The vacancy diffusion model takes internal stresses by dislocations and mismatch strains into account and it is coupled to the dislocation dynamics model in a numerically efficient way. This model is helpful for understanding the fundamental creep mechanisms in superalloys and clarifying the effects of dislocation glide and climb on creep deformation. In cases where the precipitate cutting rarely occurs, e.g. due to the high anti-phase boundary energy and the lack of superdislocations, the dislocation glide in the γ matrix and the dislocation climb along the γ/γ‧ interface dominate plastic deformation. The simulation results show that a high temperature or a high stress both promote dislocation motion and multiplication, so as to cause a large creep strain. Dislocation climb accelerated by high temperature only produces a small plastic strain, but relaxes the hardening caused by the filling γ channels and lets dislocations further glide and multiply. The strongest variation of vacancy concentration occurs in the horizontal channels, where more mixed dislocations exit and tend to climb. The increasing internal stresses due to the increasing dislocation density are easily overcome by dislocations under a high external stress that leads to a long-term dislocation glide accompanied by multiplication.

  10. Mechanical and microstructural behavior of oxide dispersion strengthened 8Cr-2W and 8Cr-1W steels during creep deformation

    Energy Technology Data Exchange (ETDEWEB)

    Shinozuka, K.; Tamura, M.; Esaka, H. [National Defense Academy, Dept. MS and E, Kanagawa (Japan); Shiba, K.; Nakamura, K. [Japan Atomic Energy Agency, Tokai-mura, Naga-gun, Ibaraki-ken (Japan)

    2007-07-01

    Full text of publication follows: Oxide dispersion strengthened (ODS) steel is a promising candidate for fusion reactor material because of excellent mechanical properties. However, the ODS steel exhibits some defects, such as mechanical anisotropy and little elongation . To reveal details of these defects, we investigated correlations between mechanical and microstructural behavior of ODS ferritic steels during creep deformation at high temperature. The materials used in this study are two kinds of hot rolled ODS steels: Fe-8Cr-2W-0.2V-0.1Ta-0.2Ti-0.4Y{sub 2}O{sub 3} (J1) and Fe-8Cr-1W-0.2Ti-0.4Y{sub 2}O{sub 3} (J2). Creep tests was carried out on specimens sampling along both the rolling direction and the cross direction at 670, 700 and 730 deg. C. Microstructural analyses were made on the normalized and tempered condition by using OM, SEM, TEM and XRD. Creep ruptured and interrupted specimens were also investigated. Both J1 and J2 existed two phases, namely martensite and {delta}-ferrite which was elongated in the rolling direction. Y-Ti complex oxide particles were finely dispersed in martensite and {delta}- ferrite phases. Results of creep tests indicated that the time-to-rupture of specimens of J1 were much longer than J2, and the time-to-rupture of specimens sampling along the rolling direction were longer than cross direction. Accordingly, J1 sampling along hot rolling direction was the strongest, for instance, the time-to-rupture was 11400 h at 700 deg. C and 162 MPa. All specimens indicated that elongation was less than 1.3 % and the rupture occurred at steady state creep region from creep curves. Internal cracks were propagated in martensite phase along elongated {delta}-ferrite phase in the direction of hot rolling. On the other hand, {delta}-ferrite phases seemed to prevent combining cracks. These results suggest that elongated {delta}-ferrite and internal clacks in martensite strongly affect on the anisotropy and little elongation of creep. (authors)

  11. Creep behavior of reduced activation martensitic steel F82H injected with a large amount of helium

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, N. E-mail: yamamoto.norikazu@nims.go.jp; Murase, Y.; Nagakawa, J.; Shiba, K

    2002-12-01

    Creep response against DEMO reactor level helium was examined on F82H steel, a candidate structural material for advanced fusion systems. Helium was injected into the material at 823 K to a concentration of about 1000 appm utilizing {alpha}-particle irradiation with a cyclotron. Post-injection creep rupture tests were conducted at the same temperature. It has been demonstrated that helium brought about no significant effect on a variety of creep properties (lifetime, rupture elongation and minimum creep rate). In parallel with this, it did not cause any influence on fracture appearance. Both helium implanted and unimplanted samples were failed in a completely transcrystalline and ductile fashion. No symptom of helium induced grain boundary separation was thereby observed even after high concentration helium introduction. These facts hint a fairly good resistance of this material toward high temperature helium embrittlement even for long-time service in fusion reactors.

  12. Investigation on the Flexural Creep Stiffness Behavior of PC-ABS Material Processed by Fused Deposition Modeling Using Response Surface Definitive Screening Design

    Science.gov (United States)

    Mohamed, Omar Ahmed; Masood, Syed Hasan; Bhowmik, Jahar Lal

    2017-03-01

    The resistance of polymeric materials to time-dependent plastic deformation is an important requirement of the fused deposition modeling (FDM) design process, its processed products, and their application for long-term loading, durability, and reliability. The creep performance of the material and part processed by FDM is the fundamental criterion for many applications with strict dimensional stability requirements, including medical implants, electrical and electronic products, and various automotive applications. Herein, the effect of FDM fabrication conditions on the flexural creep stiffness behavior of polycarbonate-acrylonitrile-butadiene-styrene processed parts was investigated. A relatively new class of experimental design called "definitive screening design" was adopted for this investigation. The effects of process variables on flexural creep stiffness behavior were monitored, and the best suited quadratic polynomial model with high coefficient of determination ( R 2) value was developed. This study highlights the value of response surface definitive screening design in optimizing properties for the products and materials, and it demonstrates its role and potential application in material processing and additive manufacturing.

  13. Investigation on the Flexural Creep Stiffness Behavior of PC-ABS Material Processed by Fused Deposition Modeling Using Response Surface Definitive Screening Design

    Science.gov (United States)

    Mohamed, Omar Ahmed; Masood, Syed Hasan; Bhowmik, Jahar Lal

    2016-12-01

    The resistance of polymeric materials to time-dependent plastic deformation is an important requirement of the fused deposition modeling (FDM) design process, its processed products, and their application for long-term loading, durability, and reliability. The creep performance of the material and part processed by FDM is the fundamental criterion for many applications with strict dimensional stability requirements, including medical implants, electrical and electronic products, and various automotive applications. Herein, the effect of FDM fabrication conditions on the flexural creep stiffness behavior of polycarbonate-acrylonitrile-butadiene-styrene processed parts was investigated. A relatively new class of experimental design called "definitive screening design" was adopted for this investigation. The effects of process variables on flexural creep stiffness behavior were monitored, and the best suited quadratic polynomial model with high coefficient of determination (R 2) value was developed. This study highlights the value of response surface definitive screening design in optimizing properties for the products and materials, and it demonstrates its role and potential application in material processing and additive manufacturing.

  14. STUDY OF ANISOTROPIC CREEP BEHAVIOR OF FRACTURED GRANITE%裂隙花岗岩各向异性蠕变特性研究

    Institute of Scientific and Technical Information of China (English)

    潘鹏志; 冯夏庭; 申林方; 杨金保; 周辉

    2011-01-01

    Due to the heterogeneity of rocks and the complex environment around rock mass, rock mass always presents anisotropic creep behavior in the loading process.In order to describe the anisotropic creep behavior of rocks, a viscoplastic fluidity parameter tensor is proposed; and the anisotropic visco-elastoplastic creep model of fractured rock is developed.The rock matrix and fracture are represented by introducing statistical distribution and weak element, respectively.A cellular automaton creep updating rule is established.This model is integrated into the EPCA3D and a numerical system EPCA3D-EVP to simulate the creep failure process of heterogeneous rocks is compiled in VC++ environment.The model and numerical method are validated against creep tests of fractured granite, which comes from the nuclear waste underground disposal candidate site in Beishan, Gansu province, China, with consideration of hydro-mechanical coupling effect.It is found that, larger lateral creep deformation of fractured granite under the effect of seepage, compared with the situation in dry condition.The EPCA3D-EVP system is used to simulate the creep test process.It is found that the simulated results are in well agreement with experiments, indicating that the developed model can well reflect the anisotropic creep phenomenon of fractured granite under the hydro-mechanical environment.The developed model can be used to long-term stability analysis of rock mass under complex conditions.%由于岩石的非均质性、裂隙的存在以及所处地质环境的复杂性,岩样在蠕变破坏过程中通常表现出各向异性的特点.为了描述岩石的这种各向异性蠕变性质,在经典弹黏塑性理论的基础上,提出黏塑性流动系数张量表达式,建立岩石各向异性弹黏塑性蠕变模型,将该模型嵌入到三维弹塑性细胞自动机模型中,开发岩石蠕变过程分析的三维弹黏塑性细胞自动机模拟系统(EPCA3D-EVP),建立非均质岩石蠕变破

  15. Creep behavior and microstructural correlation of a particle-strengthened Nb{endash}1Zr{endash}0.1C alloy

    Energy Technology Data Exchange (ETDEWEB)

    Farkas, D.M.; Mukherjee, A.K. [Department of Chemical Engineering and Materials Science, University of California, Davis, California 95616 (United States)

    1996-09-01

    The steady-state creep behavior of a particle-strengthened alloy of niobium (Nb{endash}1Zr{endash}0.1C) was compared with pure niobium and a Nb{endash}1Zr alloy. The approach to a threshold stress was indicated at stress levels below 16 MPa and was supported by a statistical analysis of mean particle size. Analysis of the crept microstructure showed a classic dislocation substructure whose cell size was inversely proportional to the applied stress except at very low stresses. The smaller than predicted cell size observed at low applied stresses was attributed to the particles, preventing the dislocation cells from reaching their equilibrium dimension. Some amount of particle growth was observed which lead to a reduction in creep resistance with time. {copyright} {ital 1996 Materials Research Society.}

  16. COMPARE THE BEHAVIOR FACTOR OF THE ULTIMATE RESISTANCE OF MOMENT FRAME, PLAIN AND PERFORATED STEEL PLATE SHEAR WALLS AND BUCKLING RESTRAINED BRACE AS YIELDING METAL DAMPER

    OpenAIRE

    Hamid Reza Ashrafi; Peyman Beiranvand; Kasra Shahbazian; Shaahin Bidmeshki; Somaye Yaghooti

    2016-01-01

    Steel moment frame systems, steel plate shear walls and also buckling restrained brace (BRB) are considered as the most widely used seismic resistant systems of the world. Firstly, in this research, in order to validate the finite element models, the tested sample of steel plate shear walls of 4 floors at the University of Alberta, Canada, and the tested sample of buckling restrained brace at the University of Berkeley California, with the software ABAQUS 6.10-1 were used. Then, the obtained ...

  17. Short-Term Creep Behavior of CFRP-Reinforced Wood Composites Subjected to Cyclic Loading at Different Climate Conditions

    Directory of Open Access Journals (Sweden)

    Xiaojun Yang

    2014-02-01

    Full Text Available Carbon fiber reinforced plastic (CFRP was used to adhesively reinforce Chinese fir (Cunninghamia lanceolata wood specimens. This study examined the flexural static and creep performances of CFPR-reinforced wood composites that had been subjected to changes in moisture and stress levels. The major findings were as follows: 1 the cyclic creep was slightly lower for those specimens subjected to the cyclic stress condition than for those subjected to a constant stress level due to the deflection recovery under cyclic loading; 2 the environmental conditions of high temperature and high humidity assisted in accelerating the creep by increasing the moisture content of the composite and reducing the compressive strength of wood, causing the composite specimen to fail via damage in the wood layer from compressive crushing; 3 the stress level governed the creep of the CFRP-reinforced wood composite; and 4 the Burger model was able to accurately simulate the short-term creep performance of the CFPR-reinforced wood composite. It was suggested the maximum bending stress level should be limited to 40% for the CFRP-reinforced wood composites fabricated in this study.

  18. Long-Term Creep Behavior of the Intervertebral Disc: Comparison between Bioreactor Data and Numerical Results

    Directory of Open Access Journals (Sweden)

    APG eCastro

    2014-11-01

    Full Text Available The Loaded Disc Culture System (LDCS is an Intervertebral Disc (IVD-oriented bioreactor developed by the VU Medical Center (VUmc, Amsterdam, The Netherlands, which has the capacity of maintaining up to 12 IVDs in culture, for approximately 3 weeks after extraction. Using this system, 8 goat IVDs were provided with the essential nutrients and submitted to compression tests without losing their biomechanical and physiological properties, for 22 days. Based on previous reports (Detiger et al., 2013; Paul et al., 2013, 2012, 4 of these IVDs were kept in physiological condition (control and the other 4 were previously injected with chondroitinase ABC (CABC, in order to promote Degenerative Disc Disease (DDD. The loading profile intercalated 16h of activity loading with 8h of loading recovery to express the standard circadian variations.The displacement behavior of these 8 IVDs along the first 2 days of the experiment was numerically reproduced, using an IVD osmo-poro-hyper-viscoelastic and fiber-reinforced Finite Element (FE model. The simulations were run on a custom FE solver (Castro et al., 2014.The analysis of the experimental results allowed concluding that the effect of the CABC injection was only significant in 2 of the 4 IVDs. The 4 control IVDs showed no signs of degeneration, as expected. In what concerns to the numerical simulations, the IVD FE model was able to reproduce the generic behavior of the two groups of goat IVDs (control and injected. However, some discrepancies were still noticed on the comparison between the injected IVDs and the numerical simulations, namely on the recovery periods. This may be justified by the complexity of the pathways for DDD, associated with the multiplicity of physiological responses to each direct or indirect stimulus. Nevertheless, one could conclude that ligaments, muscles and IVD covering membranes could be added to the FE model, in order to improve its accuracy and properly describe the recovery

  19. Creep fracture behavior of dissimilar weld joints between T92 martensitic and HR3C austenitic steels

    Energy Technology Data Exchange (ETDEWEB)

    Cao Jian; Gong Yi [Department of Materials Science, Fudan University, Shanghai 200433 (China); Yang Zhenguo, E-mail: zgyang@fudan.edu.c [Department of Materials Science, Fudan University, Shanghai 200433 (China); Luo Xiaoming; Gu Fuming [Shanghai Institute of Special Equipment Inspection and Technical Research, Shanghai 200062 (China); Hu Zhengfei [School of Materials Science and Engineering, Tongji University, Shanghai 200092 (China)

    2011-02-15

    The creep fracture of T92/HR3C dissimilar weld joints is investigated. HR3C austenitic steel is welded with T92 martensitic steel to obtain a T92/HR3C weld joint. After welding, creep tests are carried out at 625 {sup o}C in the stress range 110-180 MPa. The results indicate that the creep fracture mechanism is dependent on stress. When stresses {>=}140 MPa, the fracture location is at the T92 base material and the connection of adjacent dimples results in transcrystalline fracture. For stresses <140 MPa, the fracture location is at the T92 coarse-grained heat affected zone and growth of M{sub 23}C{sub 6} particles as well as Laves phase (Fe{sub 2}(W, Mo)) precipitation on the grain boundaries leads to intergranular fracture.

  20. Effects of thermomechanical processing on tensile and long-time creep behavior of Nb-1 percent Zr-0.1 percent C sheet

    Science.gov (United States)

    Titran, Robert H.; Uz, Mehmet

    1994-01-01

    Effects of thermomechanical processing on the mechanical properties of Nb-1 wt. percent Zr-0.1 wt. percent C, a candidate alloy for use in advanced space power systems, were investigated. Sheet bars were cold rolled into 1-mm thick sheets following single, double, or triple extrusion operations at 1900 K. All the creep and tensile specimens were given a two-step heat treatment 1 hr at 1755 K + 2 hr 1475 K prior to testing. Tensile properties were determined at 300 as well as at 1350 K. Microhardness measurements were made on cold rolled, heat treated, and crept samples. Creep tests were carried out at 1350 K and 34.5 MPa for times of about 10,000 to 19,000 hr. The results show that the number of extrusions had some effects on both the microhardness and tensile properties. However, the long-time creep behavior of the samples were comparable, and all were found to have adequate properties to meet the design requirements of advanced power systems regardless of thermomechanical history. The results are discussed in correlation with processing and microstructure, and further compared to the results obtained from the testing of Nb-1 wt. percent Zr and Nb-1 wt. percent Zr-0.06 wt. percent C alloys.

  1. Engineering tools for robust creep modelling

    OpenAIRE

    Holmström, Stefan

    2010-01-01

    High temperature creep is often dealt with simplified models to assess and predict the future behavior of materials and components. Also, for most applications the creep properties of interest require costly long-term testing that limits the available data to support design and life assessment. Such test data sets are even smaller for welded joints that are often the weakest links of structures. It is of considerable interest to be able to reliably predict and extrapolate long term creep beha...

  2. Cylindrical shell buckling through strain hardening

    Energy Technology Data Exchange (ETDEWEB)

    Bandyopadhyay, K.; Xu, J.; Shteyngart, S. [Brookhaven National Lab., Upton, NY (United States); Gupta, D. [USDOE, Germantown, MD (United States)

    1995-04-01

    Recently, the authors published results of plastic buckling analysis of cylindrical shells. Ideal elastic-plastic material behavior was used for the analysis. Subsequently, the buckling analysis program was continued with the realistic stress-strain relationship of a stainless steel alloy which does not exhibit a clear yield point. The plastic buckling analysis was carried out through the initial stages of strain hardening for various internal pressure values. The computer program BOSOR5 was used for this purpose. Results were compared with those obtained from the idealized elastic-plastic relationship using the offset stress level at 0.2% strain as the yield stress. For moderate hoop stress values, the realistic stress-grain case shows a slight reduction of the buckling strength. But, a substantial gain in the buckling strength is observed as the hoop stress approaches the yield strength. Most importantly, the shell retains a residual strength to carry a small amount of axial compressive load even when the hoop stress has exceeded the offset yield strength.

  3. The Effect of Microstructure on the Creep behavior of Ti-6Al-2Nb-1Ta-0.8Mo.

    Science.gov (United States)

    1985-09-01

    J. Gittus , "Creep, Viscoelasticity and Creep Fracture in Solids"* Applied Science Publishers LTD, London, England, 1975. 36. S. M. L. Sastry, P. S...Induced by Load Cycling in a C-Mn Steel ", Acta. Met., Vol. No. 24, 511 (1976). 75. C. E. Feltner, Trans. AIME, Vol. No. 227, 798 (1963). 76. E, W. Lee...34The Effect of Strain-Rate on the Cyclic Deformation Properties ofza- Iron Single Crystals", Acta. Met., Vol. No. 24, 659 (1976). 79. H. G. Paris, B. G

  4. Creep-rupture behavior of a developmental cast-iron-base alloy for use up to 800 deg C

    Science.gov (United States)

    Titran, Robert H.; Scheuermann, Coulson M.

    1987-01-01

    A promising iron-base cast alloy is being developed as part of the DOE/NASA Stirling Engine Systems Project under contract DEN 3-282 with the United Technologies Research Center. This report presents the results of a study at the Lewis Research Center of the alloy's creep-rupture properties. The alloy was tested under a variety of conditions and was found to exhibit the normal 3-stage creep response. The alloy compared favorably with others being used or under consideration for the automotive Stirling engine cylinder/regenerator housing.

  5. Influence of UV Light on Creep Behavior of Polypropylene%紫外光对PP蠕变行为的影响

    Institute of Scientific and Technical Information of China (English)

    刘小林; 孙世利; 陈健; 刘罡; 杨其; 李光宪

    2011-01-01

    The effect of UV light on the creep behavior of PP was studied by UV irradiation. The creep behavior and creep failure mechanisms of PP under UV irradiation were studied by creep property test, GPC、 XPS、 PALS and SEM analysis. It was found that the UV could accelerate creep failure of PP. The failure mechanisms were connected with UV radiation intensity. The short-term failure was mainly caused by the change of the activity of molecular chain; and the long-term failure was due to strength weakness of materials caused by UV. In addition, under the same external conditions(temperature, tensile stress and UV light), the failure rate for different types of PP had been found to be independent of the structure and molecular weight, depending only on the yield strength at certain temperature, the higher the yield strength was, the slower the failure rate was.%通过对聚丙烯(PP)施加紫外光的方法研究了紫外光对其蠕变行为的影响,利用蠕变性能测试、GPC、XPS、PALS、SEM等手段考察了紫外光作用下的PP蠕变行为及其失效机理.实验结果表明:紫外光能加速PP的蠕变失效,其失效机理与辐照强度有关;短时间失效主要是由紫外光引起的分子链段的活性变化所致,长时间作用下的失效,主要是紫外光引起的老化导致材料强度的削弱所致;另外,对不同种类的PP,在相同的外部条件下(温度、应力和紫外光),其失效速率与结构和分子量无关,只与该温度下材料的屈服强度有关,屈服强度越高,抗蠕变能力越好.

  6. Thermally Induced Asymmetric Buckling of Circular Monolayer Graphene

    Directory of Open Access Journals (Sweden)

    Haw-Long Lee

    2013-01-01

    Full Text Available The asymmetric buckling behaviors of circular monolayer graphene with clamped boundary condition subjected to temperature change are analytically studied based on the nonlocal elasticity theory, including the small length effect. The axisymmetrical and asymmetric critical buckling temperatures and mode shape of different order modes are obtained. According to the analysis, the asymmetric critical buckling temperature of monolayer graphene is larger than the axisymmetric one. The axisymmetrical and asymmetric critical buckling temperatures decrease with increasing nonlocal parameter. In addition, nodal diametrical lines and nodal circles can be found from the modal shapes. In order to avoid destruction of the sensors due to buckling of the structure, they can be placed at the nodal diametrical lines or nodal circles.

  7. Buckling of Carbon Nanotubes: A State of the Art Review

    Directory of Open Access Journals (Sweden)

    Hiroyuki Shima

    2011-12-01

    Full Text Available The nonlinear mechanical response of carbon nanotubes, referred to as their “buckling” behavior, is a major topic in the nanotube research community. Buckling means a deformation process in which a large strain beyond a threshold causes an abrupt change in the strain energy vs. deformation profile. Thus far, much effort has been devoted to analysis of the buckling of nanotubes under various loading conditions: compression, bending, torsion, and their certain combinations. Such extensive studies have been motivated by (i the structural resilience of nanotubes against buckling, and (ii the substantial influence of buckling on their physical properties. In this contribution, I review the dramatic progress in nanotube buckling research during the past few years.

  8. Creep Properties of Walikukun (Schouthenia ovata Timber Beams

    Directory of Open Access Journals (Sweden)

    Ali Awaludin

    2016-09-01

    Full Text Available This study presents an evaluation of creep constants of Walikukun (Schoutheniaovata timber beams when rheological model of four solid elements, which is obtained byassembling Kelvin and Maxwell bodies in parallel configuration, was adopted. Creep behaviorobtained by this method was further discussed and compared with creep behavior developedusing phenomenological model of the previous study. Creep data of previous study was deformationmeasurement of Walikukun beams having cross-section of 15 mm by 20 mm with a clearspan of 550 mm loaded for three weeks period under two different room conditions: with andwithout Air Conditioner. Creep behavior given by both four solid elements model and phenomenological(in this case are power functions had good agreement during the period of creepmeasurement, but they give different prediction of creep factor beyond this period. The powerfunction of phenomenological model could give a reasonable creep prediction, while for the foursolid elements model a necessary modification is required to adjust its long-term creep behavior.

  9. COMPARISON OF FATIGUE AND CREEP BEHAVIOR BETWEEN 2D AND 3D-C/SiC COMPOSITES

    Institute of Scientific and Technical Information of China (English)

    D. Han; S.R. Qiao; M. Li; J.T. Hou; X.J. Wu

    2004-01-01

    The differences of tension-tension fatigue and tensile creep characters of 2D-C/SiCand 3D-C/SiC composites have been scrutinized to meet the engineering needs. Experiments of tension-tension fatigue and tensile creep are carried out under vacuum high temperature condition. All of the high temperature fatigue curves are flat; the fatigue curves of the 2D-C/SiC are flatter and even parallel to the horizontal axis. While the tension-tension fatigue limit of the 3D-C/SiC is higher than that of the 2D-C/SiC, the fiber pullout length of the fatigue fracture surface of the 3D-C/SiC is longer than that of the 2D-C/SiC, and fracture morphology of the 3D-C/SiC is rougher, and pullout length of the fiber tows is longer. At the same time the 3D-C/SiC has higher tensile creep resistance. The tensile curve and the tensile creep curve of both materials consist of a series of flat step. These phenomena can be explained by the non-continuity of the damage.

  10. Creep behavior of the F82H steel under irradiation with 17 MeV protons at 300 deg. C

    Energy Technology Data Exchange (ETDEWEB)

    Nagakawa, Johsei [National Institute for Materials Science (NIMS), 1-2-1 Sengen, Tsukuba, Ibaraki 305-0047 (Japan); Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, 6-1 Kasuga Koen, Kasuga, Fukuoka 816-8580 (Japan)], E-mail: NAGAKAWA.Johsei@nims.go.jp; Uchio, S. [National Institute for Materials Science (NIMS), 1-2-1 Sengen, Tsukuba, Ibaraki 305-0047 (Japan); Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, 6-1 Kasuga Koen, Kasuga, Fukuoka 816-8580 (Japan); Murase, Y.; Yamamoto, N. [National Institute for Materials Science (NIMS), 1-2-1 Sengen, Tsukuba, Ibaraki 305-0047 (Japan); Shiba, K. [Japan Atomic Energy Agency (JAEA), 2-4 Shirakata, Tokai-Mura, Ibaraki-Ken 319-1195 (Japan)

    2009-04-30

    Although fusion blankets are exposed to severe irradiation, its rear side would stay at rather a modest condition. In this research, the irradiation-induced deformation of F82H IEA-heat steel at 300 deg. C was examined. A torsion creep apparatus with a strain resolution of {approx}10{sup -7} was used with 17 MeV protons (2 x 10{sup -7} dpa/s). At the lowest stress of 30 MPa, deformation in the direction against applied stress was observed. This 'negative creep' was attributed to the increase in elastic modulus due to irradiation. Such an effect was compensated for each measurement based on the modulus data measured during irradiation. Stress exponent n of irradiation creep rates was 1.5, very close to that of creep strain at 5 dpa of pressurized tubes. The predicted stress relaxation was slower than that for 5% cold-worked Type 316L steel, resulting mainly from the difference in n, smaller and closer to unity in the latter.

  11. Flexural creep behaviour of jute polypropylene composites

    Science.gov (United States)

    Chandekar, Harichandra; Chaudhari, Vikas

    2016-09-01

    Present study is about the flexural creep behaviour of jute fabric reinforced polypropylene (Jute-PP) composites. The PP sheet and alkali treated jute fabric is stacked alternately and hot pressed in compression molding machine to get Jute-PP composite laminate. The flexural creep study is carried out on dynamic mechanical analyzer. The creep behaviour of the composite is modeled using four-parameter Burgers model. Short-term accelerated creep testing is conducted which is later used to predict long term creep behaviour. The feasibility of the construction of a master curve using the time-temperature superposition (TTS) principle to predict long term creep behavior of unreinforced PP and Jute-PP composite is investigated.

  12. Creep of parylene-C film

    KAUST Repository

    Lin, Jeffrey Chun-Hui

    2011-06-01

    The glass transition temperature of as-deposited parylene-C is first measured to be 50°C with a ramping-temperature-dependent modulus experiment. The creep behavior of parylene-C film in the primary and secondary creep region is then investigated below and above this glass transition temperature using a dynamic mechanical analysis (DMA) machine Q800 from TA instruments at 8 different temperatures: 10, 25, 40, 60, 80, 100, 120 and 150°C. The Burger\\'s model, which is the combined Maxwell model and Kelvin-Voigt model, fits well with our primary and secondary creep data. Accordingly, the results show that there\\'s little or no creep below the glass transition temperature. Above the glass transition temperature, the primary creep and creep rate increases with the temperature, with a retardation time constant around 6 minutes. © 2011 IEEE.

  13. Room temperature creep in metals and alloys

    Energy Technology Data Exchange (ETDEWEB)

    Deibler, Lisa Anne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Materials Characterization and Performance

    2014-09-01

    Time dependent deformation in the form of creep and stress relaxation is not often considered a factor when designing structural alloy parts for use at room temperature. However, creep and stress relaxation do occur at room temperature (0.09-0.21 Tm for alloys in this report) in structural alloys. This report will summarize the available literature on room temperature creep, present creep data collected on various structural alloys, and finally compare the acquired data to equations used in the literature to model creep behavior. Based on evidence from the literature and fitting of various equations, the mechanism which causes room temperature creep is found to include dislocation generation as well as exhaustion.

  14. Effect of Cross-linking Density on Creep and Recovery Behavior in Epoxy-Based Shape Memory Polymers (SMEPs) for Structural Applications

    Science.gov (United States)

    Rao, Kavitha V.; Ananthapadmanabha, G. S.; Dayananda, G. N.

    2016-12-01

    Epoxy-based shape memory polymers (SMEPs) are gaining importance in the area of aerospace structures due to their high strength and stiffness which is a primary requirement for an SMEP in structural applications. The understanding of viscoelastic behavior of SMEPs is very essential to assess their shape memory effect. In the present work, three types of SMEPs with varying cross-linking densities were developed by curing an aromatic epoxy resin with aliphatic amines. Glass transition temperature ( T g) was measured for these SMEPs using advanced rheometric expansion system, and from the T g measurements, a range of temperatures from glassy to rubbery regimes were chosen. At selected temperatures, creep-recovery tests were performed in order to evaluate the viscoelastic behavior of SMEPs and also to investigate the effect of temperature on creep-recovery. Further, a three-parameter viscoelastic model (Zener) was used to fit the data obtained from experiments. Model parameters like moduli of the springs and viscosity of the dashpot were evaluated by curve fitting. Results revealed that Zener model was well suited to describe the viscoelastic behavior of SMEPs as a function of test temperatures.

  15. COMPARE THE BEHAVIOR FACTOR OF THE ULTIMATE RESISTANCE OF MOMENT FRAME, PLAIN AND PERFORATED STEEL PLATE SHEAR WALLS AND BUCKLING RESTRAINED BRACE AS YIELDING METAL DAMPER

    Directory of Open Access Journals (Sweden)

    Hamid Reza Ashrafi

    2016-03-01

    Full Text Available Steel moment frame systems, steel plate shear walls and also buckling restrained brace (BRB are considered as the most widely used seismic resistant systems of the world. Firstly, in this research, in order to validate the finite element models, the tested sample of steel plate shear walls of 4 floors at the University of Alberta, Canada, and the tested sample of buckling restrained brace at the University of Berkeley California, with the software ABAQUS 6.10-1 were used. Then, the obtained results of the test and analysis have been compared. The confirmed models have been used for the analysis of two-dimensional frame of plain and perforated steel plate shear walls with a regular pattern of positing holes in the screen, buckling restrained brace and moment frame of 4 floors.

  16. Out-plane buckling behavior and application of three-storey multi-column subjected to axial load%三层通高区群柱面外稳定性能与设计方法研究

    Institute of Scientific and Technical Information of China (English)

    郭彦林; 王永海

    2011-01-01

    The buckling behavior of a compressed column braced with two spring supports, as the equivalent model of three-storey multi-column frame, was investigated systemically in the previous study. It was observed that, with the bracing stiffness increasing, the buckling mode of the column changed from symmetric single wave to antisymmetric double waves before the fully fixed supported reaction was reached. Obviously, two lateral supports in the equivalent model were independent, and the stiffness of the supports was the same even under different buckling mode. However, the two lateral supports of the column were not independent in three-storey multi-column frame subjected to different buckling modes, and the interaction between lateral bracing stiffness of columns and different buckling modes needs to be taken account. In this study , the out-plane lateral bracing stiffness of the columns under different buckling modes in three-storey multi-column frame was obtained via theoretical derivation, so that the column braced with two lateral spring supports could be treated as an equivalent model where the column has different lateral brace stiffness under corresponding buckling mode. The elastic buckling load and effective slenderness of the multi-column were obtained by using the results obtained from the equivalent model. The ultimate load-carrying capacity of three-storey multi-column frame with imperfections was analyzed by using finite element method. The random out-plane imperfection distributions of different columns in the frame were considered in the study above. It was proved that the design approach of the equivalent model could be used to estimate the load-carrying capacity of three-storey multi-column frame.%对带两个等跨布置侧向弹簧支撑的轴压柱(三层通高群柱的面外稳定性等效模型)的研究表明,随着柱子受到支撑作用的增强,柱子最低阶屈曲模态会依次经历单波、双波及三波(完全支撑)三种

  17. Optical manifestation of buckled configurations in graphene-like materials

    Science.gov (United States)

    Kazemlou, V.; Phirouznia, A.; Jamshidi-Ghaleh, K.

    2017-04-01

    In the present study, the effects of the configuration buckling on dielectric function of silicene, germanene and stanene are investigated. The behavior of the optical absorption spectrum and the refractive index dispersion are studied using the density functional theory in terms of incident photon energy at different buckling heights. The results show that for a fixed bond length, increasing the unit cell buckling height, increases the absorption and the refractive index in silicene and germanene but decreases in stanene. In addition, the absorption peaks shift toward the longer wavelengths (red shift) in the case of silicene and germanene by increasing the buckling height. For clear understanding of the mentioned results, the behavior of the optical absorption spectrum and refractive index dispersion at different buckling heights are studied within the present work. In the case of the silicene and germanene reduction of the band gap with increasing the buckling height could be regarded as the origin of this red shift. Meanwhile unlike the silicene and germanene, band-structure reshaping in stanene could explain the stanene blue shift as a result of the buckling height increment.

  18. Global buckling assessment of high pressure and high temperature (HP/HT) offshore pipeline

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Seung-Ho; Jung, Jong-Jin; Lee, Woo-Seob [Maritime Research Institute, Hyundai Heavy Industries, Ulsan, (Korea, Republic of); Kim, Yun-Hak; Kim, Jong-Bae [Offshore Installation Engineering Department, Hyundai Heavy Industries, Ulsan, (Korea, Republic of)

    2010-07-01

    High pressure and high temperature (HP/HT) offshore pipelines are frequently subjected to lateral buckling due to excessive compressive axial force. Several control processes have been designed such as sleepers to reduce lateral buckling. This paper investigated the effect of the introduction of sleepers as buckle triggers on the behavior of HP/HT pipelines. A 3D finite element analysis using ABAQUS software was performed to simulate concrete sleepers and a profile of the seabed. The analysis criteria were the buckling amplitude, Von Mises stress, equivalent plastic strain and the effective axial force on the pipeline. A case study for HP/HT pipeline was been carried out based on installation surveys. Comparisons between the results from a model without buckle trigger and those from a model with buckle trigger were carried out. It was found that the change to the support structure, adding a buckle trigger, affected the behaviour of the pipeline considerably.

  19. Experimental and Numerical Study of Buckling of Vacuum Chambers for Fast-Cycling Synchrotrons

    DEFF Research Database (Denmark)

    Bräuner, Lars Erik

    The optimal functioning of the long span thin walled elliptical cross section shells used as vacuum chambers for fast-cycling synchrotrons is provided by their buckling capacity. Also it is often necessary to design inter-stiffener panels of elliptical shells used as vacuum chambers to resist any...... tendency towards pressure induced buckling due to some combination of excessive out-gassing, fragility, radiation damage, magnetic field distortion,. The analysis for design is complicated because elliptical shell chambers display a complex form of nonlinear snap buckling behavior under the external...... pressure. Buckling analysis for shells is further complicated by the observation that geometric imperfections have an important influence on the buckling mode as well as on the buckling load-carrying capacity. Buckling loads are, in general, considerably lower than the lowest critical loads predicted from...

  20. Scleral Buckling with Chandelier Illumination.

    Science.gov (United States)

    Seider, Michael I; Nomides, Riikka E K; Hahn, Paul; Mruthyunjaya, Prithvi; Mahmoud, Tamer H

    2016-01-01

    Scleral buckling is a highly successful technique for the repair of rhegmatogenous retinal detachment that requires intra-operative examination of the retina and treatment of retinal breaks via indirect ophthalmoscopy. Data suggest that scleral buckling likely results in improved outcomes for many patients but is declining in popularity, perhaps because of significant advances in vitrectomy instrumentation and visualization systems. Emerging data suggest that chandelier-assisted scleral buckling is safe and has many potential advantages over traditional buckling techniques. By combining traditional scleral buckling with contemporary vitreoretinal visualization techniques, chandelier-assistance may increase the popularity of scleral buckling to treat primary rhegmatogenous retinal detachment for surgeons of the next generation, maintaining buckling as an option for appropriate patients in the future.

  1. Scleral buckling with chandelier illumination

    Directory of Open Access Journals (Sweden)

    Michael I Seider

    2016-01-01

    Full Text Available Scleral buckling is a highly successful technique for the repair of rhegmatogenous retinal detachment that requires intra-operative examination of the retina and treatment of retinal breaks via indirect ophthalmoscopy. Data suggest that scleral buckling likely results in improved outcomes for many patients but is declining in popularity, perhaps because of significant advances in vitrectomy instrumentation and visualization systems. Emerging data suggest that chandelier-assisted scleral buckling is safe and has many potential advantages over traditional buckling techniques. By combining traditional scleral buckling with contemporary vitreoretinal visualization techniques, chandelier-assistance may increase the popularity of scleral buckling to treat primary rhegmatogenous retinal detachment for surgeons of the next generation, maintaining buckling as an option for appropriate patients in the future.

  2. Large earthquakes and creeping faults

    Science.gov (United States)

    Harris, Ruth A.

    2017-01-01

    Faults are ubiquitous throughout the Earth's crust. The majority are silent for decades to centuries, until they suddenly rupture and produce earthquakes. With a focus on shallow continental active-tectonic regions, this paper reviews a subset of faults that have a different behavior. These unusual faults slowly creep for long periods of time and produce many small earthquakes. The presence of fault creep and the related microseismicity helps illuminate faults that might not otherwise be located in fine detail, but there is also the question of how creeping faults contribute to seismic hazard. It appears that well-recorded creeping fault earthquakes of up to magnitude 6.6 that have occurred in shallow continental regions produce similar fault-surface rupture areas and similar peak ground shaking as their locked fault counterparts of the same earthquake magnitude. The behavior of much larger earthquakes on shallow creeping continental faults is less well known, because there is a dearth of comprehensive observations. Computational simulations provide an opportunity to fill the gaps in our understanding, particularly of the dynamic processes that occur during large earthquake rupture and arrest.

  3. Creep characterization of solder bumps using nanoindentation

    Science.gov (United States)

    Du, Yingjie; Liu, Xiao Hu; Fu, Boshen; Shaw, Thomas M.; Lu, Minhua; Wassick, Thomas A.; Bonilla, Griselda; Lu, Hongbing

    2017-08-01

    Current nanoindentation techniques for the measurement of creep properties are applicable to viscoplastic materials with negligible elastic deformations. A new technique for characterization of creep behavior is needed for situations where the elastic deformation plays a significant role. In this paper, the effect of elastic deformation on the determination of creep parameters using nanoindentation with a self-similar nanoindenter tip is evaluated using finite element analysis (FEA). It is found that the creep exponent measured from nanoindentation without taking into account of the contribution of elastic deformation tends to be higher than the actual value. An effective correction method is developed to consider the elastic deformation in the calculation of creep parameters. FEA shows that this method provides accurate creep exponent. The creep parameters, namely the creep exponent and activation energy, were measured for three types of reflowed solder bumps using the nanoindentation method. The measured parameters were verified using FEA. The results show that the new correction approach allows extraction of creep parameters with precision from nanoindentation data.

  4. Effect of silver and indium addition on mechanical properties and indentation creep behavior of rapidly solidified Bi-Sn based lead-free solder alloys

    Energy Technology Data Exchange (ETDEWEB)

    Shalaby, Rizk Mostafa, E-mail: rizk1969@yahoo.co.uk [Mansoura University, Metal Physics Lab., Physics Department, Faculty of Science, Al-Gomhouria Street, Mansoura, P.O.Box 35516 (Egypt)

    2013-01-10

    Mechanical properties and indentation creep of the melt-spun process Bi-42 wt%Sn, Bi-40 wt%Sn-2 wt%In, Bi-40 wt%Sn-2 wt%Ag and Bi-38 wt%Sn-2 wt%In-2 wt%Ag were studied by dynamic resonance technique and Vickers indentation testing at room temperature and compared to that of the traditional Sn-37 wt%Pb eutectic alloy. The results show that the structure of Bi-42 wt%Sn alloy is characterized by the presence of rhombohedral Bi and body centered tetragonal {beta}-Sn. The two ternary alloys exhibit additional constituent phases of intermetallic compounds SnIn{sub 19} for Bi-40 wt%Sn-2 wt%In and {epsilon}-Ag{sub 3}Sn for Bi-40 wt%Sn-2 wt%Ag alloys. Attention has been paid to the role of intermetallic compounds on mechanical and creep behavior. The In and Ag containing solder alloy exhibited a good combination of higher creep resistance, good mechanical properties and lower melting temperature as compared with Pb-Sn eutectic solder alloy. This was attributed to the strengthening effect of Bi as a strong solid solution element in the Sn matrix and formation of intermetallic compounds {beta}-SnBi, {epsilon}-Ag{sub 3}Sn and InSn{sub 19} which act as both strengthening agent and grain refiner in the matrix of the material. Addition of In and Ag decreased the melting temperature of Bi-Sn lead-free solder from 143 Degree-Sign C to 133 Degree-Sign C which was possible mainly due to the existence of InSn{sub 19} and Ag{sub 3}Sn intermetallic compounds. Elastic constants, internal friction and thermal properties of Bi-Sn based alloys have been studied and analyzed.

  5. Dynamic buckling of actin within filopodia

    DEFF Research Database (Denmark)

    Leijnse, Natascha; Oddershede, Lene B; Bendix, Pól Martin

    2015-01-01

    Filopodia are active tubular structures protruding from the cell surface which allow the cell to sense and interact with the surrounding environment through repetitive elongation-retraction cycles. The mechanical behavior of filopodia has been studied by measuring the traction forces exerted...... on external substrates.(1) These studies have revealed that internal actin flow can transduce a force across the cell surface through transmembrane linkers like integrins. In addition to the elongation-retraction behavior filopodia also exhibit a buckling and rotational behavior. Filopodial buckling...... microsphere which acts like an external substrate attached to the filopodial tip. There is a clear correlation between presence of actin near the tip and exertion of a traction force, thus demonstrating that the traction force is transduced along the actin shaft inside the filopodium. By extending...

  6. A New Creep Constitutive Model for 7075 Aluminum Alloy Under Elevated Temperatures

    Science.gov (United States)

    Lin, Y. C.; Jiang, Yu-Qiang; Zhou, Hua-Min; Liu, Guan

    2014-12-01

    Exposure of aluminum alloy to an elastic loading, during "creep-aging forming" or other manufacturing processes at relatively high temperature, may lead to the lasting creep deformation. The creep behaviors of 7075 aluminum alloy are investigated by uniaxial tensile creep experiments over wide ranges of temperature and external stress. The results show that the creep behaviors of the studied aluminum alloy strongly depend on the creep temperature, external stress, and creep time. With the increase of creep temperature and external stress, the creep strain increases quickly. In order to overcome the shortcomings of the Bailey-Norton law and θ projection method, a new constitutive model is proposed to describe the variations of creep strain with time for the studied aluminum alloy. In the proposed model, the dependences of creep strain on the creep temperature, external stress, and creep time are well taken into account. A good agreement between the predicted and measured creep strains shows that the established creep constitutive model can give an accurate description of the creep behaviors of 7075 aluminum alloy. Meanwhile, the obtained stress exponent indicates that the creep process is controlled by the dislocation glide, which is verified by the microstructural observations.

  7. Interaction between particle precipitation and creep behavior in the NI-base Alloy 617B: Microstructural observations and constitutive material model

    Energy Technology Data Exchange (ETDEWEB)

    Haan, J., E-mail: j.haan@iwm.rwth-aachen.de; Bezold, A., E-mail: a.bezold@iwm.rwth-aachen.de; Broeckmann, C., E-mail: c.broeckmann@iwm.rwth-aachen.de

    2015-07-29

    The creep behavior of the Ni-base Alloy 617B was analyzed at 725 °C with the focus on microstructural changes during temperature and stress exposure. High resolution electron microscopy of crept specimens reveals the precipitation behavior of secondary phases such as Cr-rich M{sub 23}C{sub 6}-carbides and the γ'-phase. Physical models are used to describe the Ostwald coarsening of the γ' particles and the evolution of the yield strength of the alloy. Together with the results from hot tensile tests and hardness measurements, a constitutive model for Alloy 617B has been developed. This model takes account of precipitation strengthening which is consistent with the microstructural observations, internal back stress due to dislocation hardening and material damage, all by evolutionary equations.

  8. Experimental approach and micro-mechanical modeling of the creep behavior of irradiated zirconium alloys; Approche experimentale et modelisation micromecanique du comportement en fluage des alliages de zircomium irradies

    Energy Technology Data Exchange (ETDEWEB)

    Ribis, J

    2007-12-15

    The fuel rod cladding, strongly affected by microstructural changes due to irradiation such as high density of dislocation loops, is strained by the end-of-life fuel rod internal pressure and the potential release of fission gases and helium during dry storage. Within the temperature range that is expected during dry interim storage, cladding undergoes long term creep under over-pressure. So, in order to have a predictive approach of the behavior of zirconium alloys cladding in dry storage conditions it is essential to take into account: initial dislocation loops, thermal annealing of loops and creep straining due to over pressure. Specific experiments and modelling for irradiated samples have been developed to improve our knowledge in that field. A Zr-1%Nb-O alloy was studied using fine microstructural investigations and mechanical testing. The observations conducted by transmission electron microscopy show that the high density of loops disappears during a heat treatment. The loop size becomes higher and higher while their density falls. The microhardness tests reveal that the fall of loop density leads to the softening of the irradiated material. During a creep test, both temperature and applied stress are responsible of the disappearance of loops. The loops could be swept by the activation of the basal slip system while the prism slip system is inhibited. Once deprived of loops, the creep properties of the irradiated materials are closed to the non irradiated state, a result whose consequence is a sudden acceleration of the creep rate. Finally, a micro-mechanical modeling based on microscopic deformation mechanisms taking into account experimental dislocation loop analyses and creep test, was used for a predictive approach by constructing a deformation mechanism map of the creep behavior of the irradiated material. (author)

  9. Crack buckling in soft gels under compression

    Institute of Scientific and Technical Information of China (English)

    Rong Long; Chung-Yuen Hui

    2012-01-01

    Recent interest in designing soft gels with high fracture toughness has called for simple and robust methods to test fracture behavior.The conventional method of applying tension to a gel sample suffers from a difficulty of sample gripping.In this paper,we study a possible fracture mechanism of soft gels under uni-axial compression.We show that the surfaces of a pre-existing crack,oriented parallel to the loading axis,can buckle at a critical compressive stress.This buckling instability can open the crack surfaces and create highly concentrated stress fields near the crack tip,which can lead to crack growth.We show that the onset of crack buckling can be deduced by a dimensional argument combined with an analysis to determine the critical compression needed to induce surface instabilities of an elastic half space.The critical compression for buckling was verified for a neoHookean material model using finite element simulations.

  10. The electromechanical response of silicon nanowires to buckling mode transitions

    Energy Technology Data Exchange (ETDEWEB)

    Wong, Chee Chung; Liao, Kin [Division of Bioengineering, Nanyang Technological University (Singapore); Reboud, Julien; Neuzil, Pavel; Soon, Jeffrey; Agarwal, Ajay; Balasubramanian, Naranayan, E-mail: pavel@kist-europe.de, E-mail: askliao@ntu.edu.sg [Institute of Microelectronics, A-STAR (Agency for Science, Technology, and Research) (Singapore)

    2010-10-08

    Here we show how the electromechanical properties of silicon nanowires (NWs) are modified when they are subjected to extreme mechanical deformations (buckling and buckling mode transitions), such as those appearing in flexible devices. Flexible devices are prone to frequent dynamic stress variations, especially buckling, while the small size of NWs could give them an advantage as ultra-sensitive electromechanical stress sensors embedded in such devices. We evaluated the NWs post-buckling behavior and the effects of buckling mode transition on their piezoresistive gauge factor (GF). Polycrystalline silicon NWs were embedded in SiO{sub 2} microbridges to facilitate concurrent monitoring of their electrical resistance without problematic interference, while an external stylus performed controlled deformations of the microbridges. At points of instability, the abrupt change in the buckling configuration of the microbridge corresponded to a sharp resistance change in the embedded NWs, without altering the NWs' GF. These results also highlight the importance of strategically positioning the NW in the devices, since electrical monitoring of buckling mode transitions is feasible when the deformations impact a region where the NW is placed. The highly flexible NWs also exhibited unusually large fracture strength, sustaining tensile strains up to 5.6%; this will prove valuable in demanding flexible sensors.

  11. Creep Behavior of Carbonaceous Slate under Stepwise Loading%分级加载下炭质板岩蠕变特性的试验研究

    Institute of Scientific and Technical Information of China (English)

    宋勇军; 雷胜友; 邹翀; 刘昭; 王吉庆

    2013-01-01

    Creep behavior is one of the important mechanical properties of rock material,and is closely related with the long-term stability and safety of rock engineering.To investigate the creep characteristics of Carbonaceous slate,uniaxial creep tests under different stress levels were carried out on RLW-1000 rheology testing machine.The creep test result was analyzed by using generalized Kelvin model,Burgers model and FC (function component) assembly model.The results showed that FC model had good fitting results in low stress level,while in high stress level,Burgers model had better fitting results than the other two models.In general,Burgers model could effectively reflect the creep characteristics of carbonaceous slate in all stress levels.Moreover,parameter fitting results in different stress levels indicated that the viscous coefficient increased along with the time development in low stress level,and significantly reduced with time in high load stress,which presented as the function of time and stress-level.The research results can offer model parameters and design basis for further understanding the creep properties of carbonaceous slates.%蠕变特性是岩石类材料的重要力学性质之一,与岩石工程的长期稳定和安全密切相关.为了解炭质板岩的蠕变特性,采用RLW-1000岩石流变试验机进行了单轴压缩蠕变试验.选用广义Kelvin模型、Burgers模型及FC元件组合模型进行了参数拟合分析.分析表明:板岩在低应力水平下,FC元件组合模型拟合效果较好,而在高应力水平下Burgers模型拟合结果优于其余2种模型.总体来讲,不论应力水平的高低,Burgers模型能够较好地反映炭质板岩的蠕变特性.同时,对不同应力水平下的蠕变曲线进行参数拟合,发现黏滞系数在较低应力水平下随时间而增大,而在较高加载应力下随时间显著减小,表现为应力水平和时间的函数,研究成果可为进一步了解该岩石的蠕变特性提供模型参数和设计依据.

  12. Experimental Study on the Mechanical, Creep, and Viscoelastic Behavior of TiO2/Glass/Epoxy Hybrid Nanocomposites

    Science.gov (United States)

    Salehi, H. R.; Salehi, M.

    2016-11-01

    The mechanical and viscoelastic properties of hybrid glass/epoxy nanocomposites whose matrix was doped with 0.25, 0.5, and 1 vol.% of TiO2 nanoparticles were investigated in tension and bending. The nanoparticles were found to increase the strength of the composites by 20-30% and their stiffness by 10-20%. In addition, their creep resistance also grew. A SEM analysis of microstructure of the composites revealed that these improvements were caused by an increased adhesion between fibers and the matrix and enhanced properties of the matrix itself.

  13. Inversion of hysteresis and creep operators

    Science.gov (United States)

    Krejčí, Pavel; Al Janaideh, Mohammad; Deasy, Fergal

    2012-05-01

    The explicit inversion formula for rate dependent Prandtl-Ishlinskii operators is extended to cases without the threshold dilation condition. This solves a problem in hysteresis and creep modeling of magnetostrictive behavior.

  14. Scleral Buckling with Chandelier Illumination

    OpenAIRE

    Michael I Seider; Riikka E.K Nomides; Paul Hahn; Prithvi Mruthyunjaya; Mahmoud, Tamer H

    2016-01-01

    Scleral buckling is a highly successful technique for the repair of rhegmatogenous retinal detachment that requires intra-operative examination of the retina and treatment of retinal breaks via indirect ophthalmoscopy. Data suggest that scleral buckling likely results in improved outcomes for many patients but is declining in popularity, perhaps because of significant advances in vitrectomy instrumentation and visualization systems. Emerging data suggest that chandelier-assisted scleral buckl...

  15. Buckle Driven Delamination in Thin Hard Film Compliant Substrate Systems

    Directory of Open Access Journals (Sweden)

    Bahr D.F.

    2010-06-01

    Full Text Available Deformation and fracture of thin films on compliant substrates are key factors constraining the performance of emerging flexible substrate devices. [1-3] These systems often contain layers of thin polymer, ceramic and metallic films and stretchable interconnects where differing properties induce high normal and shear stresses. [4] As long as the films remain bonded to the substrates, they may deform far beyond their freestanding form. Once debonded, substrate constraint disappears leading to film failure. [3] Experimentally it is very difficult to measure properties in these systems at sub-micron and nanoscales. Theoretically it is very difficult to determine the contributions from the films, interfaces, and substrates. As a result our understanding of deformation and fracture behavior in compliant substrate systems is limited. This motivated a study of buckle driven delamination of thin hard tungsten films on pure PMMA substrates. The films were sputter deposited to thicknesses of 100 nm, 200 nm, and 400 nm with a residual compressive stress of 1.7 GPa. An aluminum oxide interlayer was added on several samples to alter interfacial composition. Buckles formed spontaneously on the PMMA substrates following film deposition. On films without the aluminum oxide interlayer, an extensive network of small telephone cord buckles formed following deposition, interspersed with regions of larger telephone cord buckles. (Figure 1 On films with an aluminum oxide interlayer, telephone cord buckles formed creating a uniform widely spaced pattern. Through-substrate optical observations revealed matching buckle patterns along the film-substrate interface indicating that delamination occurred for large and small buckles with and without an interlayer. The coexistence of large and small buckles on the same substrate led to two distinct behaviors as shown in Figure 2 where normalized buckle heights are plotted against normalized film stress. The behaviors deviate

  16. Buckle Driven Delamination in Thin Hard Film Compliant Substrate Systems

    Science.gov (United States)

    Moody, N. R.; Reedy, E. D.; Corona, E.; Adams, D. P.; Kennedy, M. S.; Cordill, M. J.; Bahr, D. F.

    2010-06-01

    Deformation and fracture of thin films on compliant substrates are key factors constraining the performance of emerging flexible substrate devices. [1-3] These systems often contain layers of thin polymer, ceramic and metallic films and stretchable interconnects where differing properties induce high normal and shear stresses. [4] As long as the films remain bonded to the substrates, they may deform far beyond their freestanding form. Once debonded, substrate constraint disappears leading to film failure. [3] Experimentally it is very difficult to measure properties in these systems at sub-micron and nanoscales. Theoretically it is very difficult to determine the contributions from the films, interfaces, and substrates. As a result our understanding of deformation and fracture behavior in compliant substrate systems is limited. This motivated a study of buckle driven delamination of thin hard tungsten films on pure PMMA substrates. The films were sputter deposited to thicknesses of 100 nm, 200 nm, and 400 nm with a residual compressive stress of 1.7 GPa. An aluminum oxide interlayer was added on several samples to alter interfacial composition. Buckles formed spontaneously on the PMMA substrates following film deposition. On films without the aluminum oxide interlayer, an extensive network of small telephone cord buckles formed following deposition, interspersed with regions of larger telephone cord buckles. (Figure 1) On films with an aluminum oxide interlayer, telephone cord buckles formed creating a uniform widely spaced pattern. Through-substrate optical observations revealed matching buckle patterns along the film-substrate interface indicating that delamination occurred for large and small buckles with and without an interlayer. The coexistence of large and small buckles on the same substrate led to two distinct behaviors as shown in Figure 2 where normalized buckle heights are plotted against normalized film stress. The behaviors deviate significantly from

  17. Buckling of dislocation in graphene

    Science.gov (United States)

    Yao, Yin; Wang, Shaofeng; Bai, Jianhui; Wang, Rui

    2016-10-01

    The buckling of dislocation in graphene is discussed through the lattice theory of dislocation and elastic theory. The approximate solution of the buckling is obtained based on the inner stress distribution caused by different structure of dislocations and is proved to be suitable by the simulation. The position of the highest buckling is predicted to be at the vertex of the pentagon far away from the heptagon. The buckling is strongly influenced by the internal stress and the distance between the extrusive area and stretching area, as well as the critical stress σc. The SW defect is proved to be unbuckled due to its strong interaction between extrusion and stretching.

  18. Study of Buckling Restrained Braces in Steel Frame Building

    Directory of Open Access Journals (Sweden)

    Mr. Y. D. Kumbhar

    2014-08-01

    Full Text Available Conventional braces have limited deformation ductility capacity, and exhibit unsymmetrical hysteretic cycles, with marked strength deterioration when loaded in compression. To overcome the above mentioned problems, a new type of brace was developed in Japan called as buckling restrained braces, designated as BRB’s. These braces are designed such that buckling is inhibited to occur, exhibiting adequate behavior and symmetrical hysteretic curves under the action of both tensile and compressive cycles, produced by the action of seismic and wind forces. This paper presents experimental results concerning the lateral load carrying capacity of steel frame model by use of buckling restrained brace. This paper also includes the comparative study of lateral load carrying capacity of frame model for bare frame, frame with Conventional brace and frame with buckling restrained brace.

  19. Buckling analysis of a ring stiffened hybrid composite cylinder

    Science.gov (United States)

    Potluri, Rakesh; Eswara Kumar, A.; Navuri, Karteek; Nagaraju, M.; Mojeswara Rao, Duduku

    2016-09-01

    This study aims to understand the response of the ring stiffened cylinders made up of hybrid composites subjected to buckling loads by using the concepts of Design of Experiments (DOE) and optimization by using Finite Element Method (FEM) simulation software Ansys workbench V15. Carbon epoxy and E-glass epoxy composites were used in the hybrid composite. This hybrid composite was analyzed by using different layup angles. Central composite design (CCD) was used to perform design of experiments (D.O.E) and kriging method was used to generate a response surface. The response surface optimization (RSO) was performed by using the method of the multi-objective genetic algorithm (MOGA). After optimization, the best candidate was chosen and applied to the ring stiffened cylinder and eigenvalue buckling analysis was performed to understand the buckling behavior. Best laminate candidates with high buckling strength have been identified. A generalized procedure of the laminate optimization and analysis have been shown.

  20. Scale effects on thermal buckling properties of carbon nanotube

    Energy Technology Data Exchange (ETDEWEB)

    Wang Yize, E-mail: wangyize@gmail.co [P.O. Box 137, School of Astronautics, Harbin Institute of Technology, Harbin 150001 (China); Department of Mechanical Sciences and Engineering, Tokyo Institute of Technology, 2-12-1, O-okayama, Meguro-ku, Tokyo 152-8552 (Japan); Li Fengming, E-mail: fmli@hit.edu.c [P.O. Box 137, School of Astronautics, Harbin Institute of Technology, Harbin 150001 (China); Kishimoto, Kikuo [Department of Mechanical Sciences and Engineering, Tokyo Institute of Technology, 2-12-1, O-okayama, Meguro-ku, Tokyo 152-8552 (Japan)

    2010-11-01

    In this Letter, the thermal buckling properties of carbon nanotube with small scale effects are studied. Based on the nonlocal continuum theory and the Timoshenko beam model, the governing equation is derived and the nondimensional critical buckling temperature is presented. The influences of the scale coefficients, the ratio of the length to the diameter, the transverse shear deformation and rotary inertia are discussed. It can be observed that the small scale effects are significant and should be considered for thermal analysis of carbon nanotube. The nondimensional critical buckling temperature becomes higher with the ratio of length to diameter increasing. Furthermore, for smaller ratios of the length to the diameter and higher mode numbers, the transverse shear deformation and rotary inertia have remarkable influences on the thermal buckling behaviors.

  1. Static and dynamic buckling of thin-walled plate structures

    CERN Document Server

    Kubiak, Tomasz

    2013-01-01

    This monograph deals with buckling and postbuckling behavior of thin plates and thin-walled structures with flat wall subjected to static and dynamic load. The investigations are carried out in elastic range. The basic assumption here is the  thin plate theory. This method is used to determination the buckling load and postbuckling analysis of thin-walled structures subjected to static and dynamic load. The book introduces two methods for static and dynamic buckling investigation which allow for a wider understanding of the phenomenon. Two different methods also can allow uncoupling of the phenomena occurring at the same time and attempt to estimate their impact on the final result. A general mathematical model, adopted in proposed analytical-numerical method, enables the consideration of all types of stability loss i.e.local, global and interactive forms of buckling. The applied numerical-numerical method includes adjacent of walls, shear-lag phenomenon and a deplanation of cross-sections.

  2. Creep in structures

    Energy Technology Data Exchange (ETDEWEB)

    Zyczkowski, M. (Krakow Univ. of Technology (Poland). Inst. of Mechanics and Machine Design) (ed.)

    1991-01-01

    This volume contains 81 papers divided into three almost equal parts: Constitutive equations, combined loadings; damage, creep crack growth, creep rupture; structures, analytical and numerical methods, optimal design. (orig.).

  3. Creep and Creep-Fatigue of Alloy 617 Weldments

    Energy Technology Data Exchange (ETDEWEB)

    Wright, Jill K. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Carroll, Laura J. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Wright, Richard N. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-08-01

    Alloy 617 is the primary candidate material for the heat exchanger of a very high temperature gas cooled reactor intended to operate up to 950°C. While this alloy is currently qualified in the ASME Boiler and Pressure Vessel Code for non-nuclear construction, it is not currently allowed for use in nuclear designs. A draft Code Case to qualify Alloy 617 for nuclear pressure boundary applications was submitted in 1992, but was withdrawn prior to approval. Prior to withdrawal of the draft, comments were received indicating that there was insufficient knowledge of the creep and creep-fatigue behavior of Alloy 617 welds. In this report the results of recent experiments and analysis of the creep-rupture behavior of Alloy 617 welds prepared using the gas tungsten arc process with Alloy 617 filler wire. Low cycle fatigue and creep-fatigue properties of weldments are also discussed. The experiments cover a range of temperatures from 750 to 1000°C to support development of a new Code Case to qualify the material for elevated temperature nuclear design. Properties of the welded material are compared to results of extensive characterization of solution annealed plate base metal.

  4. Creep, Fatigue and Fracture Behavior of Environmental Barrier Coating and SiC-SiC Ceramic Matrix Composite Systems: The Role of Environment Effects

    Science.gov (United States)

    Zhu, Dongming; Ghosn, Louis J.

    2015-01-01

    Advanced environmental barrier coating (EBC) systems for low emission SiCSiC CMC combustors and turbine airfoils have been developed to meet next generation engine emission and performance goals. This presentation will highlight the developments of NASAs current EBC system technologies for SiC-SiC ceramic matrix composite combustors and turbine airfoils, their performance evaluation and modeling progress towards improving the engine SiCSiC component temperature capability and long-term durability. Our emphasis has also been placed on the fundamental aspects of the EBC-CMC creep and fatigue behaviors, and their interactions with turbine engine oxidizing and moisture environments. The EBC-CMC environmental degradation and failure modes, under various simulated engine testing environments, in particular involving high heat flux, high pressure, high velocity combustion conditions, will be discussed aiming at quantifying the protective coating functions, performance and durability, and in conjunction with damage mechanics and fracture mechanics approaches.

  5. Implications of Jeffreys-Lomnitz Transient Creep

    Science.gov (United States)

    Strick, Ellis

    1984-01-01

    In 1958 Jeffreys proposed a power law generalization of the logarithmic transient creep earlier attributed to Lomnitz. Although Jeffreys' power law form was admittedly defective in that it became unbounded at infinite time, he did apply it to the viscoelastic behavior of the earth-moon system. Since then it has been successfully applied by many investigators to mantle rehology and Chandler wobble. Experimental seismic studies indicate that most rock types exhibit the almost constant Q behavior which Lomnitz showed to be associated with his logarithmic creep. In this paper, we study not only the Q behavior related to Jeffreys' power law creep but also other mechanical properties such as a precise spring-dashpot ladder network realization are developed. In addition, a very simple physically realizable modification of this ladder network leads to a boundedness at long times of Jeffreys' creep in a manner which does not affect his successful application at finite times.

  6. Chemical controls on fault behavior: weakening of serpentinite sheared against quartz-bearing rocks and its significance for fault creep in the San Andreas system

    Science.gov (United States)

    Moore, Diane E.; Lockner, David A.

    2013-01-01

    The serpentinized ultramafic rocks found in many plate-tectonic settings commonly are juxtaposed against crustal rocks along faults, and the chemical contrast between the rock types potentially could influence the mechanical behavior of such faults. To investigate this possibility, we conducted triaxial experiments under hydrothermal conditions (200-350°C), shearing serpentinite gouge between forcing blocks of granite or quartzite. In an ultramafic chemical environment, the coefficient of friction, µ, of lizardite and antigorite serpentinite is 0.5-0.6, and µ increases with increasing temperature over the tested range. However, when either lizardite or antigorite serpentinite is sheared against granite or quartzite, strength is reduced to µ ~ 0.3, with the greatest strength reductions at the highest temperatures (temperature weakening) and slowest shearing rates (velocity strengthening). The weakening is attributed to a solution-transfer process that is promoted by the enhanced solubility of serpentine in pore fluids whose chemistry has been modified by interaction with the quartzose wall rocks. The operation of this process will promote aseismic slip (creep) along serpentinite-bearing crustal faults at otherwise seismogenic depths. During short-term experiments serpentine minerals reprecipitate in low-stress areas, whereas in longer experiments new Mg-rich phyllosilicates crystallize in response to metasomatic exchanges across the serpentinite-crustal rock contact. Long-term shear of serpentinite against crustal rocks will cause the metasomatic mineral assemblages, which may include extremely weak minerals such as saponite or talc, to play an increasingly important role in the mechanical behavior of the fault. Our results may explain the distribution of creep on faults in the San Andreas system.

  7. The secondary buckling transition: wrinkling of buckled spherical shells.

    Science.gov (United States)

    Knoche, Sebastian; Kierfeld, Jan

    2014-07-01

    We theoretically explain the complete sequence of shapes of deflated spherical shells. Decreasing the volume, the shell remains spherical initially, then undergoes the classical buckling instability, where an axisymmetric dimple appears, and, finally, loses its axisymmetry by wrinkles developing in the vicinity of the dimple edge in a secondary buckling transition. We describe the first axisymmetric buckling transition by numerical integration of the complete set of shape equations and an approximate analytic model due to Pogorelov. In the buckled shape, both approaches exhibit a locally compressive hoop stress in a region where experiments and simulations show the development of polygonal wrinkles, along the dimple edge. In a simplified model based on the stability equations of shallow shells, a critical value for the compressive hoop stress is derived, for which the compressed circumferential fibres will buckle out of their circular shape in order to release the compression. By applying this wrinkling criterion to the solutions of the axisymmetric models, we can calculate the critical volume for the secondary buckling transition. Using the Pogorelov approach, we also obtain an analytical expression for the critical volume at the secondary buckling transition: The critical volume difference scales linearly with the bending stiffness, whereas the critical volume reduction at the classical axisymmetric buckling transition scales with the square root of the bending stiffness. These results are confirmed by another stability analysis in the framework of Donnel, Mushtari and Vlasov (DMV) shell theory, and by numerical simulations available in the literature.

  8. The Impact of Weld Metal Creep Strength on the Overall Creep Strength of 9% Cr Steel Weldments

    OpenAIRE

    Mayr, Peter; Mitsche, Stefan; Cerjak, Horst; Allen, Samuel Miller

    2010-01-01

    In this work, three joints of a X11CrMoWVNb9-1-1 (P911) pipe were welded with three filler metals by conventional arc welding. The filler metals varied in creep strength level, so that one overmatched, one undermatched, and one matched the creep strength of the P911 grade pipe base material. The long-term objective of this work was to study the influence of weld metal creep strength on the overall creep behavior of the welded joints and their failure mechanism. Uniaxial creep tests at 600°C a...

  9. 软土固结蠕变特性及机制研究%Experimental study of coupling behaviors of consolidation-creep of soft clay and its mechanism

    Institute of Scientific and Technical Information of China (English)

    张先伟; 王常明; 李军霞

    2011-01-01

    以黄石地区软土为研究对象,在不同排水条件、固结压力作用下开展固结蠕变试验,对原状样与蠕变后试样进行扫描电镜观测,分析软土的固结蠕变特性及其微观机制.结果表明:不排水条件下蠕变特性表现更为显著.低偏应力作用下,排水条件下试样的变形大于不排水条件下的变形;高偏应力作用下,则与之相反.排水条件下,变形是由蠕变和固结共同产生的,具有线性蠕变特性;不排水条件下,蠕变是变形的主要原因,具有非线性蠕变特性.蠕变过程中,颗粒间以边-边、边-面为主的接触形式向以面-面为主的接触形式过渡,颗粒间距减小,大孔隙减少,小孔隙增多.固结过程中的主要是自由水以及渗透吸收结合水转化为自由水的排出,而蠕变阶段主要受结合水控制,随着压力加大,孔隙体积减小,结合水膜变薄,增大了土的黏滞性,在长时期就表现为蠕变特性.在软土地基加固过程中可提高土体的排水性能,增大土体的固结程度,降低蠕变带来的危害,提高建筑物的稳定性.%In order to analyze micromechanism and coupled behaviors of consolidation and creep of soft clay, the consolidation and creep test at different drainage conditions and different consolidation pressures and the scanning electron microscopy test of the undisturbed sample and sample after creep are carried out from soft clay in the Yellowstone region. The results show that the creep behaviors under undrained condition are even more significant compared with under drained condition. Under lower bias stress condition, the deformation under drained condition is larger comparatively and with the opposite conclusion under higher bias stress condition. The deformations under drained condition are induced by consolidation and creep which have linear creep properties; and the deformations under undrained condition are induced mainly by creep which has nonlinear creep properties

  10. Low Temperature Creep of Hot-Extruded Near-Stoichiometric NiTi Shape Memory Alloy. Part I; Isothermal Creep

    Science.gov (United States)

    Raj, S. V.; Noebe, R. D.

    2013-01-01

    This two-part paper is the first published report on the long term, low temperature creep of hot-extruded near-stoichiometric NiTi. Constant load tensile creep tests were conducted on hot-extruded near-stoichiometric NiTi at 300, 373 and 473 K under initial applied stresses varying between 200 and 350 MPa as long as 15 months. These temperatures corresponded to the martensitic, two-phase and austenitic phase regions, respectively. Normal primary creep lasting several months was observed under all conditions indicating dislocation activity. Although steady-state creep was not observed under these conditions, the estimated creep rates varied between 10(exp -10) and 10(exp -9)/s. The creep behavior of the two phases showed significant differences. The martensitic phase exhibited a large strain on loading followed by a primary creep region accumulating a small amount of strain over a period of several months. The loading strain was attributed to the detwinning of the martensitic phase whereas the subsequent strain accumulation was attributed to dislocation glide-controlled creep. An "incubation period" was observed before the occurrence of detwinning. In contrast, the austenitic phase exhibited a relatively smaller loading strain followed by a primary creep region, where the creep strain continued to increase over several months. It is concluded that the creep of the austenitic phase occurs by a dislocation glide-controlled creep mechanism as well as by the nucleation and growth of deformation twins.

  11. Buckling of polymerized monomolecular films

    Science.gov (United States)

    Bourdieu, L.; Daillant, J.; Chatenay, D.; Braslau, A.; Colson, D.

    1994-03-01

    The buckling of a two-dimensional polymer network at the air-water interface has been evidenced by grazing incidence x-ray scattering. A comprehensive description of the inhomogeneous octadecyltrichlorosilane polymerized film was obtained by atomic force microscopy and x-ray scattering measurements. The buckling occurs with a characteristic wavelength ~=10 μm.

  12. Creep in ceramics

    CERN Document Server

    Pelleg, Joshua

    2017-01-01

    This textbook is one of its kind, since there are no other books on Creep in Ceramics. The book consist of two parts: A and B. In part A general knowledge of creep in ceramics is considered, while part B specifies creep in technologically important ceramics. Part B covers creep in oxide ceramics, carnides and nitrides. While covering all relevant information regarding raw materials and characterization of creep in ceramics, the book also summarizes most recent innovations and developments in this field as a result of extensive literature search.

  13. The effect of temperature on the compressive buckling of boron nitride nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Shokuhfar, Ali; Ebrahimi-Nejad, Salman [Faculty of Mechanical Engineering, K.N. Toosi University of Technology, 19991-43344 Tehran (Iran, Islamic Republic of); Hosseini-Sadegh, Amin [Faculty of Petroleum Engineering, Petroleum University of Technology, 14539-53153 Tehran (Iran, Islamic Republic of); Zare-Shahabadi, Abolfazl [Department of Mechanical Engineering, Yazd Branch, Islamic Azad University, Yazd (Iran, Islamic Republic of)

    2012-07-15

    Inspired by the stability at high temperature and the high mechanical strength of boron nitride nanotubes (BNNTs), the effect of temperature on the compressive buckling of BNNTs has been investigated in this paper. Molecular dynamics (MD) simulations of BNNTs subjected to high temperatures (up to 3000 K) were performed and their structures were analyzed by studying their optimized structures at different temperatures through the radial distribution function (RDF). Then, the structural stability and compressive resistance properties of these nanotubes were investigated and the critical buckling loads and critical buckling strains of the nanotubes and their susceptibility to high temperatures were determined. The gradual decrease in the sharpness of the peaks of RDF plots of non-loaded nanotubes implies that at higher temperatures the structure displays greater deviations from that at room temperature. Results of buckling simulations also indicate a general weakening of the nanotubes and lower critical buckling loads and critical buckling strains at increased temperatures. The decrease in the critical buckling load is more significant for the longer nanotube (L {proportional_to} 6 nm) than the shorter one (L {proportional_to} 3 nm). The critical buckling strain experienced a drop of about 35-50% at temperatures higher than 1500 K. A transitional behavior was observed between T = 1000 and 2000 K. Temperature-dependent axial buckling behavior of boron nitride nanotubes. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  14. Buckling failures in insect exoskeletons.

    Science.gov (United States)

    Parle, Eoin; Herbaj, Simona; Sheils, Fiona; Larmon, Hannah; Taylor, David

    2016-02-01

    Thin walled tubes are often used for load-bearing structures, in nature and in engineering, because they offer good resistance to bending and torsion at relatively low weight. However, when loaded in bending they are prone to failure by buckling. It is difficult to predict the loading conditions which cause buckling, especially for tubes whose cross sections are not simple shapes. Insights into buckling prevention might be gained by studying this phenomenon in the exoskeletons of insects and other arthropods. We investigated the leg segments (tibiae) of five different insects: the locust (Schistocerca gergaria), American cockroach (Periplaneta americana), death's head cockroach (Blaberus discoidalis), stick insect (Parapachymorpha zomproi) and bumblebee (Bombus terrestris audax). These were tested to failure in cantilever bending and modelled using finite element analysis (FEA). The tibiae of the locust and the cockroaches were found to be approximately circular in shape. Their buckling loads were well predicted by linear elastic FEA, and also by one of the analytical solutions available in the literature for elastic buckling. The legs of the stick insect are also circular in cross section but have several prominent longitudinal ridges. We hypothesised that these ridges might protect the legs against buckling but we found that this was not the case: the loads necessary for elastic buckling were not reached in practice because yield occurred in the material, causing plastic buckling. The legs of bees have a non-circular cross section due to a pollen-carrying feature (the corbicula). We found that this did not significantly affect their resistance to buckling. Our results imply that buckling is the dominant failure mode in the tibia of insects; it likely to be a significant consideration for other arthropods and any organisms with stiff exoskeletons. The interactions displayed here between material properties and cross sectional geometry may provide insights for the

  15. Documentation for the viscoplastic and creep program

    DEFF Research Database (Denmark)

    Bellini, Anna

    2004-01-01

    of this workpackage is to simulate creep behavior of aluminum cast samples subjected to high temperature. In this document a two-state variables unified model is applied in order to simulate creep behavior and time-dependent metallurgical changes. The fundamental assumption of the unified theory is that creep...... and viscoplasticity, which are both irreversible strains developed because of dislocations motion in the material structure, can be modelled through the implementation of a similar plastic strain velocity law, generally called flow rule. The document shows how to obtain the material data needed for the simulation...... is run using the material data obtained through the mentioned experimental study. The results obtained for the simulation of tensile tests and of creep tests are compared with experimental curves, showing a good agreement. Moreover, the document describes the results obtained during the first...

  16. Creep of frozen soil by damage mechanics

    Institute of Scientific and Technical Information of China (English)

    苗天德; 魏雪霞; 张长庆

    1995-01-01

    A microstructure damage theory for creep of frozen soil under the frame of damage mechan-ics is presented.Based on the test study and microscope observation,several internal variables are chosen tocharacterize the microstructure changes and the evolution equations of these internal variables are developed.The theory can describe both the "hardening" and "softening" behavior in the creep process.A detailed analysis hasbeen made for the uniaxial compressure and compared with the test data.

  17. Correlation Between Transient Regime and Steady-State Regime on Creep Crack Growth Behavior of Grade 91 Steel

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jae Young; Ekaputra, I. M. W.; Kim, Seon Jin [Pukyong National Univ., Busan (Korea, Republic of); Kim, Woo Gon; Kim, Eung Seon [KAERI, Daejeong (Korea, Republic of)

    2015-12-15

    A correlation between the transient regime and steady state regime on the creep crack growth (CCG) for Grade 91 steel, which is used as the structural material for the Gen-IV reactor systems, was investigated. A series of CCG tests were performed using 1/2' CT specimens under a constant applied load and at a constant temperature of 600 °C. The CCG rates for the transient and steady state regimes were obtained in terms of C* parameter. The transient CCG rate had a close correlation with the steady-state CCG rate, as the slope of the transient CCG data was very similar to that of the steady state data. The transient rate was slower by 5.6 times as compared to the steady state rate. It can be inferred that the steady state CCG rate, which is required for long-time tests, can be predicted from the transient CCG rate obtained from short-time tests.

  18. Super long-term creep tests of advanced HP and IP rotor steels

    Energy Technology Data Exchange (ETDEWEB)

    Tchizhik, A.A. [The Polzunov Central Boiler and Turbine Institute, Department the Fatigue Life of Materials for Power Plans Equipment, St. Petersburg (Russian Federation)

    1998-12-31

    A creep model has been developed for predicting the long-term creep behavior, in excess of 200,000 h for advanced materials.The new creep theory is based on a continuum microdamage model and is used to calculate the fields of stress and strain and wedge and cavities damage in critical components of steam and gas turbines. The application of this new model increases the reliability and service life of modern turbines. The accuracy of the model to predict long - term creep behavior, creep ductility was verified using the data bank of super long-term creep tests of advanced materials. (orig.) 12 refs.

  19. Buckling analysis of sandwich plate using layer wise theory

    Energy Technology Data Exchange (ETDEWEB)

    Ranjbaran, Arash; Khoshravan, Mohammad Reza [University of Tabriz, Tabriz (Iran, Islamic Republic of); Kharazi, Mahsa [Sahand University of Technology, Sahand (Iran, Islamic Republic of)

    2014-07-15

    Buckling analysis of sandwich plate was investigated using layer wise method. The formulation was based on the first-order shear deformation theory, and the Rayleigh-Ritz method was used for approximating and determining the displacement field. The results obtained from layer wise theory was compared with finite element results and showed good agreement. This study demonstrated that layer wise theory could describe buckling behavior of sandwich plates with high accuracy and represents a more realistic and acceptable description of behavior of the plates with much less computational cost.

  20. Buckling Characteristics of Cylindrical Pipes

    Institute of Scientific and Technical Information of China (English)

    Toshiaki Sakurai

    2015-01-01

    This paper describes the buckling pattern of the body frame by energy absorbed efficiency of crashworthiness related toresearch of the buckling characteristics of aluminum cylindrical pipes with various diameters formed mechanical tools. Experimentswere performed by the quasi-static test without lubrication between specimen and equipment. According to the change in the radiusversus thickness of the specimen, the buckling phenomena are transformed from folding to bellows and the rate of energy absorptionis understood. In crashworthiness, frames are characterized by the folding among three patterns from the absorbed energy efficiencypoint of view and weight reduction. With the development of new types of transport such as electric vehicles, innovated bodystructure should be designed.

  1. 屈曲约束支撑加固框架抗震性能试验研究%Experiment Study on Seismic Behavior of RC Frame Strengthened by Buckling-restrained Braces

    Institute of Scientific and Technical Information of China (English)

    曹炳政; 朱春明; 郑昊; 李向民

    2012-01-01

    Based on a two-layer RC frame building, two RC frames are designed with the scale 1:2. One RC frame is tested by low-reversed cyclic loading, another RC frame is tested by low-reversed cyclic loading with buckling-restrained braces. Based on the tests, the force performance, failure mode, hysteretic behavior, and displacement ductility of two RC frames are analyzed. The tests are examined by numerical simulation anlysis of the seismostruct 5. 03. The results show that the seismic behavior of RC frame with buckling-restrained braces is improved significantly.%以两层钢筋混凝土框架为原型,按1∶2的缩尺比例设计了2榀钢筋混凝土框架.对其中1榀进行了低周反复试验,对另1榀采取屈曲约束支撑加固后进行低周反复试验.试验主要研究了原型框架和屈曲约束支撑框架的受力性能、破坏形态、滞回特性以及位移延性等,并采用Seismostruct 5.03程序对试验过程进行数值模拟分析.结果表明,屈曲约束支撑混凝土框架的抗震性能有了较好的改善.

  2. Creep simulation of adhesively bonded joints using modified generalized time hardening model

    Energy Technology Data Exchange (ETDEWEB)

    Sadigh, Mohammad Ali Saeimi [Azarbaijan Shahid Madani University, Tabriz (Iran, Islamic Republic of)

    2016-04-15

    Creep behavior of double lap adhesively bonded joints was investigated using experimental tests and numerical analysis. Firstly, uniaxial creep tests were carried out to obtain the creep characteristics and constitutive parameters of the adhesive at different stress and temperature levels. Generalized time hardening model was used to predict the creep behavior of the adhesive. This model was modified to simulate the creep behavior at different stress and temperature levels. Secondly, the developed model was used to simulate the creep behavior of bonded joints using finite element based numerical analysis. Creep deformations of the joints were measured experimentally and good agreement was observed in comparison with the results obtained using numerical simulation. Afterward, stress redistribution due to the creep along the adhesively bonded joint was obtained numerically. It was observed that temperature level had a significant effect on the stress redistribution along the adhesive thickness.

  3. Nonlinear Analysis of Buckling

    Directory of Open Access Journals (Sweden)

    Psotný Martin

    2014-06-01

    Full Text Available The stability analysis of slender web loaded in compression was presented. To solve this problem, a specialized computer program based on FEM was created. The nonlinear finite element method equations were derived from the variational principle of minimum of potential energy. To obtain the nonlinear equilibrium paths, the Newton-Raphson iteration algorithm was used. Corresponding levels of the total potential energy were defined. The peculiarities of the effects of the initial imperfections were investigated. Special attention was focused on the influence of imperfections on the post-critical buckling mode. The stable and unstable paths of the nonlinear solution were separated. Obtained results were compared with those gained using ANSYS system.

  4. 湛江强结构性黏土的三轴排水蠕变特征%CREEP BEHAVIOR OF ZHANJIANG STRONG STRUCTURED CLAY BY DRAINED TRIAXIAL TEST

    Institute of Scientific and Technical Information of China (English)

    孔令伟; 张先伟; 郭爱国; 蔡羽

    2011-01-01

    利用GDS应力路径三轴试验系统,开展不同围压下湛江强结构性黏土的三轴固结排水剪切蠕变试验,获得其轴向应变、体应变与应力和时间的关系,分析蠕变性状的结构性效应,建立相应的蠕变模型.结果表明,湛江黏土的蠕变变形演化特征受其强结构性制约,其蠕变特性的敏感干程度与结构性强弱相关联.在低偏应力下,其蠕变变形和变形速率均较小;偏应力超过临界值后,土体在短时间内发生破坏.湛江黏土在σ3<σk时,其体变性状总体上表现为剪缩,但随时间变化出现一定的剪缩和剪胀交替性,即存在回弹现象;而当σ3≥σk时,则表现为剪缩.蠕变引起的强度衰减主要表现为黏聚力的降低,且C∞/Cj=77.63%.采用6元件扩展Burgers模型能较好地描述湛江黏土的瞬时弹性应变、衰减蠕变和稳定蠕变3个阶段.在实际工程中,必须对土的结构性给予充分的认识,在较低应力范围内,可以利用其结构性的有利因素,但设计荷载严禁超出结构屈服应力.%The drained triaxial shear creep tests for Zhanjiang strong structured clay under different confining pressures by GDS triaxial testing system are performed.The relationships of axial strain and volumetric strain with stress and time are obtained.The effect of soil structural property on its creep behavior is analyzed; and the corresponding creep model is established.The results show that the evolution characteristics of creep deformation of Zhanjiang clay are restricted by its poorly structural property; and its sensitivity is related to the structural property of soil.The creep deformation and deformation rate of Zhanjiang clay are small in the range of low deviatoric stress; when the deviatoric stress exceeds a critical value, the soil mass failure occurs in a short time.The overall behavior of volumetric strain of Zhanjiang clay in the process of drained triaxial shear creep presents shear contraction, while

  5. Buckling analysis of a laminate plate

    Directory of Open Access Journals (Sweden)

    Mamuzić, I.

    2008-04-01

    Full Text Available The paper deals with a modeling of laminate plates and with their buckling analysis. To predict the inception of buckling for plates in plane resultant forces must be included. The buckling analysis is made by the help of finite element method in program COSMOS/M. For rectangular laminate plate consisting of 4 layers with symmetric and antisymmetric stacking sequence a buckling analysis is carried out. In the illustrative example there are depicted buckling modes for symmetric laminates [30/-30]s, [45/-45]s, [60/-60]s, [90/-90]s and results of the buckling analysis for the symmetric and antisymmetric laminates.

  6. Rate-controlling processes in creep of subgrain containing aluminum materials

    Energy Technology Data Exchange (ETDEWEB)

    Sherby, Oleg D. [Department Materials Science and Engineering, Stanford University, Stanford, CA 94305 (United States); Ruano, Oscar A. [Department Physical Metallurgy, Centro Nacional de Investigaciones Metalurgicas, CSIC, Av. Gregorio de Amo, 8, 28040 Madrid (Spain)]. E-mail: ruano@cenim.csic.es

    2005-11-25

    The creep behavior of aluminum alloys containing Bi, Zn, Ge, Cu, Fe, Mn and Ti has been investigated. Aluminum containing solutes that diffused faster than aluminum has faster creep rates and lower activation energies for creep than observed in pure aluminum. Solutes that diffused slower than aluminum have slower creep rates and higher activation energies for creep than observed in pure aluminum. A dislocation climb model in the subgrain boundary that involves solute atom diffusion as the rate-controlling creep process is proposed to explain the results.

  7. Molecular dynamics analysis on buckling of defective carbon nanotubes.

    Science.gov (United States)

    Kulathunga, D D T K; Ang, K K; Reddy, J N

    2010-09-01

    Owing to their remarkable mechanical properties, carbon nanotubes have been employed in many diverse areas of applications. However, similar to any of the many man-made materials used today, carbon nanotubes (CNTs) are also susceptible to various kinds of defects. Understanding the effect of defects on the mechanical properties and behavior of CNTs is essential in the design of nanotube-based devices and composites. It has been found in various past studies that these defects can considerably affect the tensile strength and fracture of CNTs. Comprehensive studies on the effect of defects on the buckling and vibration of nanotubes is however lacking in the literature. In this paper, the effects of various configurations of atomic vacancy defects, on axial buckling of single-walled carbon nanotubes (SWCNTs), in different thermal environments, is investigated using molecular dynamics simulations (MDS), based on a COMPASS force field. Our findings revealed that even a single missing atom can cause a significant reduction in the critical buckling strain and load of SWCNTs. In general, increasing the number of missing atoms, asymmetry of vacancy configurations and asymmetric distribution of vacancy clusters seemed to lead to higher deterioration in buckling properties. Further, SWCNTs with a single vacancy cluster, compared to SWCNTs with two or more vacancy clusters having the same number of missing atoms, appeared to cause higher deterioration of buckling properties. However, exceptions from the above mentioned trends could be expected due to chemical instabilities of defects. Temperature appeared to have less effect on defective CNTs compared to pristine CNTs.

  8. Molecular dynamics analysis on buckling of defective carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Kulathunga, D D T K; Ang, K K [Department of Civil Engineering, National University of Singapore (Singapore); Reddy, J N, E-mail: cveangkk@nus.edu.s [Department of Mechanical Engineering, Texas A and M University, College Station, TX 77843-3123 (United States)

    2010-09-01

    Owing to their remarkable mechanical properties, carbon nanotubes have been employed in many diverse areas of applications. However, similar to any of the many man-made materials used today, carbon nanotubes (CNTs) are also susceptible to various kinds of defects. Understanding the effect of defects on the mechanical properties and behavior of CNTs is essential in the design of nanotube-based devices and composites. It has been found in various past studies that these defects can considerably affect the tensile strength and fracture of CNTs. Comprehensive studies on the effect of defects on the buckling and vibration of nanotubes is however lacking in the literature. In this paper, the effects of various configurations of atomic vacancy defects, on axial buckling of single-walled carbon nanotubes (SWCNTs), in different thermal environments, is investigated using molecular dynamics simulations (MDS), based on a COMPASS force field. Our findings revealed that even a single missing atom can cause a significant reduction in the critical buckling strain and load of SWCNTs. In general, increasing the number of missing atoms, asymmetry of vacancy configurations and asymmetric distribution of vacancy clusters seemed to lead to higher deterioration in buckling properties. Further, SWCNTs with a single vacancy cluster, compared to SWCNTs with two or more vacancy clusters having the same number of missing atoms, appeared to cause higher deterioration of buckling properties. However, exceptions from the above mentioned trends could be expected due to chemical instabilities of defects. Temperature appeared to have less effect on defective CNTs compared to pristine CNTs.

  9. Creep Test of Polymer-matrix 3-D Braided Composites

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The long-term creep behavior of polymer-matrix 3-D braided composites was studied by using the tensile creep test method, and the effect of braiding structure, braiding angle and fiber volume fraction were discussed. The creep curve appears as expected, and can be defimed two phases,namely, the primary phase and the secondary phase. For each sample, strain increases with time rapidly, and then the strain rate decreases and appears to approach a constant rate of change (steady-state creep). The experiment results show that the creep resistant properties are improved while the braiding angle decreases or the fiber volume fraction increases, and that the five-directional braiding structure offers better creep resistant properties than the fourdirectional braiding structure.

  10. Effect of surface layer thickness on buckling and vibration of nonlocal nanowires

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Kai-Ming; Zhang, Wen-Ming, E-mail: wenmingz@sjtu.edu.cn; Zhong, Zuo-Yang; Peng, Zhi-Ke; Meng, Guang

    2014-01-31

    In this Letter, the buckling and vibration behavior of nonlocal nanowires by incorporating surface elasticity is investigated. A modified core–shell model is developed to depict the size effect of Young's modulus and validated by the reported experimental data. Our results show that the buckling load and natural frequency of nanowires increase when the effect of surface layer thickness is taken into account. Moreover, as the diameter of nanowires is smaller than 50 nm, the influence of surface layer thickness becomes obvious. This work can be helpful in characterizing and predicting the buckling and vibration behavior of NWs.

  11. Structural model for the dynamic buckling of a column under constant rate compression

    CERN Document Server

    Kuzkin, Vitaly A

    2015-01-01

    Dynamic buckling behavior of a column (rod, beam) under constant rate compression is considered. The buckling is caused by prescribed motion of column ends toward each other with constant velocity. Simple model with one degree of freedom simulating static and dynamic buckling of a column is derived. In the case of small initial disturbances the model yields simple analytical dependencies between the main parameters of the problem: critical force, compression rate, and initial disturbance. It is shown that the time required for buckling is inversely proportional to cubic root of compression velocity and logarithmically depends on the initial disturbance. Analytical expression for critical buckling force as a function of compression velocity is derived. It is shown that in a range of compression rates typical for laboratory experiments the dependence is accurately approximated by a power law with exponent equal to $2/3$. Theoretical findings are supported by available results of laboratory experiments. Keywords...

  12. Estimation of transient creep C(t)-integrals for SE(B) specimen under elastic-plastic creep

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Han Sang; Je, Jin Ho; Kim, Dong Jun; Kim, Yun Jae [Dept. of Mechanical Engineering, Korea University, Seoul (Korea, Republic of)

    2015-09-15

    In this paper, we estimate the time-dependent C(t) integrals under elastic-plastic-creep conditions. Finite-element (FE) transient creep analyses have been performed for single-edge-notched-bend (SEB) specimens. We investigate the effect of the initial plasticity on the transient creep by systematically varying the magnitude of the initial step load. We consider both the same stress exponent and different stress exponents in the power-law creep and plasticity to elastic-plastic-creep behavior. To estimate the C(t) integrals, we compare the FE analysis results with those obtained using formulas. In this paper, we propose a modified equation to predict the C(t) integrals for the case of creep exponents that are different from the plastic exponent.

  13. Viscous Creep in Dry Unconsolidated Gulf of Mexico Shale

    Science.gov (United States)

    Chang, C.; Zoback, M. D.

    2002-12-01

    We conducted laboratory experiments to investigate creep characteristics of dry unconsolidated shale recovered from the pathfinder well, Gulf of Mexico (GOM). We subjected jacketed cylindrical specimens (25.4 mm diameter) to hydrostatic pressure that increased from 10 to 50 MPa in steps of 5 MPa. We kept the pressure constant in each step for at least 6 hours and measured axial and lateral strains (provided by LVDTs) and ultrasonic velocities (provided by seismic-wave transducers). The dry shale exhibited pronounced creep strain at all pressure levels, indicating that the dry frame of the shale possesses an intrinsic viscous property. Interestingly, the creep behavior of the shale is different above and below 30 MPa confining pressure. Above 30 MPa, the amount of creep strain in 6 hours is nearly constant with equal pressurization steps, indicating a linear viscous rheology. Below 30 MPa, the amount of creep increases linearly as pressure is raised in constant incremental steps, suggesting that the creep deformation accelerates as pressure increases within this pressure range. Thus, the general creep behavior of the GOM shale is characterized by a bilinear dependence on pressure magnitude. This creep characteristic is quite different from that observed in unconsolidated reservoir sands (Hagin and Zoback, 2002), which exhibited nearly constant amount of creep regardless of the pressure magnitude for equal increasing steps of pressure. The shale exhibits a lack of creep (and nearly negligible strain recovery) when unloaded, suggesting that the creep strain is irrecoverable and can be considered viscoplastic deformation. SEM observations show that the major mechanism of compaction of the dry shale appears to be packing of clay and a progressive collapse of pore (void) spaces. Creep compaction is considerably more significant than compaction that occurs instantaneously, indicating that the process of shale compaction is largely time-dependent.

  14. Research Progress on High-temperature Creep Behavior of Reactor Pressure Vessel%严重事故下反应堆压力容器材料高温蠕变研究进展

    Institute of Scientific and Technical Information of China (English)

    武志玮; 宁冬; 姚伟达

    2011-01-01

    介绍了近年来在假想堆芯熔化严重事故下国内外反应堆压力容器材料高温蠕变行为的研究进展及现状,着重阐述了在材料高温蠕变试验、缩比模型试验和数值模拟等方面取得的成果,并提出了目前存在的问题及未来的发展方向。%An overview of research status and progress on high-temperature creep behavior pressure vessel considering the hypothetical core melt down scenario is presented in this paper. is placed on accomplished achievements in The present problems as well as the future of reactor Emphasis creep tests, scale model experiments and numerical simulation. development are also suggested.

  15. Primary and secondary creep in aluminum alloys as a solid state transformation

    Science.gov (United States)

    Fernández, R.; Bruno, G.; González-Doncel, G.

    2016-08-01

    Despite the massive literature and the efforts devoted to understand the creep behavior of aluminum alloys, a full description of this phenomenon on the basis of microstructural parameters and experimental conditions is, at present, still missing. The analysis of creep is typically carried out in terms of the so-called steady or secondary creep regime. The present work offers an alternative view of the creep behavior based on the Orowan dislocation dynamics. Our approach considers primary and secondary creep together as solid state isothermal transformations, similar to recrystallization or precipitation phenomena. In this frame, it is shown that the Johnson-Mehl-Avrami-Kolmogorov equation, typically used to analyze these transformations, can also be employed to explain creep deformation. The description is fully compatible with present (empirical) models of steady state creep. We used creep curves of commercially pure Al and ingot AA6061 alloy at different temperatures and stresses to validate the proposed model.

  16. Estimation of post-buckling fatigue damage for LMFBR reactor vessel under seismic load

    Energy Technology Data Exchange (ETDEWEB)

    Ogiso, S.; Sasaki, T.; Oooka, Y. [Kawasaki Heavy Industries, Ltd., Tokyo (Japan). Nuclear Systems Div.; Nakamura, H. [Central Research Inst. of Electric Power Industry, Chiba (Japan)

    1995-12-31

    Estimation of fatigue damage caused by buckling deformation is important to evaluate safety margin in a seismic buckling design criterion for LMFBR reactor vessels, in addition to limiting the buckling strength. An advanced buckling design guideline draft including the seismic margin criterion has been proposed under the sponsorship of MITI to date. An ultimate state in this criterion was defined as the condition that the maximum global displacement {delta}{sub max} reaches a critical displacement {delta}{sub u}. The authors have previously proposed an estimation method of the fatigue damage based on the post buckling fatigue tests 304 s.s. cylinders at room temperature. However, adoption of a modified 316 s.s named 316FR s.s is under development as the material of reactor vessel of the updated design of the Demonstration Fast Breeder Reactor. The buckling tests with 316FR s.s cylinders were performed under high temperature to obtain the skeleton curve of the relation between load and displacement. And the buckling behaviors under the cyclic loading were compared with those of 304 s.s. Objectives of the present study are: to apply the proposed estimation method to a reactor vessel made of 316FR s.s., and clarify the correlation between {delta}{sub max} and fatigue failure; to verify structural soundness of the ultimate state derived from the seismic margin criterion against the fatigue failure due to the buckling deformation. (author). 7 refs., 12 figs., 1 tab.

  17. Computation Analysis of Buckling Loads of Thin-Walled Members with Open Sections

    Directory of Open Access Journals (Sweden)

    Lihua Huang

    2016-01-01

    Full Text Available The computational methods for solving buckling loads of thin-walled members with open sections are not unique when different concerns are emphasized. In this paper, the buckling loads of thin-walled members in linear-elastic, geometrically nonlinear-elastic, and nonlinear-inelastic behaviors are investigated from the views of mathematical formulation, experiment, and numerical solution. The differential equations and their solutions of linear-elastic and geometrically nonlinear-elastic buckling of thin-walled members with various constraints are derived. Taking structural angle as an example, numerical analysis of elastic and inelastic buckling is carried out via ANSYS. Elastic analyses for linearized buckling and nonlinear buckling are realized using finite elements of beam and shell and are compared with the theoretical results. The effect of modeling of constraints on numerical results is studied when shell element is applied. The factors that influence the inelastic buckling load in numerical solution, such as modeling of constraint, loading pattern, adding rib, scale factor of initial defect, and yield strength of material, are studied. The noteworthy problems and their solutions in numerically buckling analysis of thin-walled member with open section are pointed out.

  18. Irradiation creep of nano-powder sintered silicon carbide at low neutron fluences

    Energy Technology Data Exchange (ETDEWEB)

    Koyanagi, Takaaki [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States); Shimoda, Kazuya [Kyoto Univ., Kyoto (Japan); Kondo, Sosuke [Kyoto Univ., Kyoto (Japan); Hinoki, Tatsuya [Kyoto Univ., Kyoto (Japan); Ozawa, Kazumi [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States); Katoh, Yutai [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)

    2014-12-01

    The irradiation creep behavior of nano-powder sintered silicon carbide was investigated using the bend stress relaxation method under neutron irradiation up to 1.9 dpa. The creep deformation was observed at all temperatures ranging from 380 to 1180 °C mainly from the irradiation creep but with the increasing contributions from the thermal creep at higher temperatures. Microstructural observation and data analysis were performed.

  19. Creep behavior of Re-free nickel-based single crystal superalloy at intermediate temperature%无Re镍基单晶合金的中温蠕变行为

    Institute of Scientific and Technical Information of China (English)

    田素贵; 薛永超; 曾征; 舒德龙; 郭忠革; 谢君

    2013-01-01

    通过中温蠕变性能测试、组织形貌观察及位错组态的衍衬分析,研究无 Re 镍基单晶合金的蠕变行为与变形机制。结果表明:在760℃、750 MPa条件下,合金具有良好的蠕变抗力及较长的蠕变寿命,蠕变期间,合金中的γ′相仅发生粗化,未发生筏形化转变。合金在蠕变初期的变形机制是(1/2)〈110〉位错在基体通道的{111}八面体滑移系中运动,蠕变位错可发生单取向滑移、双取向滑移和交滑移;随着蠕变进入后期,合金的应变增大,其变形机制是〈110〉位错在基体中运动和剪切进入γ′相,其中,基体中的位错发生扭曲,而部分剪切进入γ′相的〈110〉超位错发生分解,形成〈112〉肖克莱不全位错+层错的位错组态,可抑制位错的交滑移,使合金具有较好的蠕变抗力。%By means of creep property measurement at intermediate temperature, microstructure observation and contrast analysis of dislocation configuration, the creep behavior and deformation mechanism of Re-free nickel-based single crystal superalloy at intermediate temperature were investigated. The results show that the alloy displays a better creep resistance and long creep life at 760℃, 750 MPa. During creep at intermediate temperature, the coarsening of the cubicalγ′ phase occurs, and no rafting transformation of γ′ phase is detected. The deformation mechanism of the superalloy during initial creep is the slipping of (1/2) dislocations with single oriented, double oriented and cross-slipping features activated on the octahedral systems in theγmatrix channels. The strain of the alloy increases as the creep enters latter stage, the deformation mechanism of the superalloy is that 〈110〉 dislocations slipping in theγmatrix and shearing enter into the cubical γ′ phase. Thereinto, the twisting of dislocations in the matrix occurs, and some 〈110〉super-dislocations shearing into γ′ phase

  20. Buckling of a single-layered graphene sheet on an initially strained InGaAs thin plate

    Energy Technology Data Exchange (ETDEWEB)

    Taziev, R M; Ya Prinz, V, E-mail: taziev@thermo.isp.nsc.ru [Institute of Semiconductor Physics, 630090, Novosibirsk (Russian Federation)

    2011-07-29

    The elastic buckling behavior of a defect-free single-layered graphene sheet deposited on a strained InGaAs substrate is investigated. Such a buckled sandwich structure can be formed by local etching of an initially strained InGaAs substrate. We numerically investigated the necessary buckling conditions for a single-layered graphene sheet of circular geometry on an initially strained InGaAs thin plate. A criterion for buckling for various axisymmetric buckling shapes was obtained. It is shown that for a thin circular InGaAs plate with a monolayer graphene sheet of radius 80 nm and thickness 4 nm three axisymmetric buckling shapes can be obtained. For an initial value of the elastic deformation of the plate of 3%, the in-plane strain in graphene can reach a value of 1%. This deformation is shown to be distributed inhomogeneously along the radius of the graphene monolayer.

  1. 聚合物膜上的微尺度金属导线在力电耦合作用下的屈曲行为%Buckling behavior of micro metal wire on polymer membrane under combined effect of electrical loading and mechanical loading

    Institute of Scientific and Technical Information of China (English)

    王庆华; 岸本哲; 谢惠民; 李艳杰; 吴丹

    2014-01-01

    The buckling behavior of a typical structure consisting of a micro constantan wire and a polymer membrane under coupled electrical-mechanical loading was studied. The phenomenon that the constantan wire delaminates from the polymer membrane was observed after unloading. The interfacial toughness of the constantan wire and the polymer membrane was estimated. Moreover, several new instability modes of the constantan wire could be further triggered based on the buckle-driven delamination. After electrical loading and tensile loading, the constantan wire was likely to fracture based on buckling. After electrical loading and compressive loading, the constantan wire was easily folded at the top of the buckling region. On the occasion, the constantan wire buckled towards the inside of the polymer membrane under electrical-compressive loading. The mechanisms of these instability modes were analyzed.%研究一种典型的微尺度康铜线/聚合物膜结构在力电耦合作用下的屈曲行为。根据卸载后康铜线从聚合物基底上屈曲的现象,评估康铜线与聚合物基底间的界面韧性。此外,力电耦合作用还会诱发新的失稳模态。在电载荷和拉伸载荷作用下,康铜线易在屈曲时发生断裂。在电载荷和压缩载荷作用下,康铜线易在屈曲区域的顶部发生折叠,偶尔还会向聚合物基底内部方向发生屈曲。分析了这些失稳模态的产生机理。

  2. Probabilistic models for creep-fatigue in a steel alloy

    Science.gov (United States)

    Ibisoglu, Fatmagul

    In high temperature components subjected to long term cyclic operation, simultaneous creep and fatigue damage occur. A new methodology for creep-fatigue life assessment has been adopted without the need to separate creep and fatigue damage or expended life. Probabilistic models, described by hold times in tension and total strain range at temperature, have been derived based on the creep rupture behavior of a steel alloy. These models have been validated with the observed creep-fatigue life of the material with a scatter band close to a factor of 2. Uncertainties of the creep-fatigue model parameters have been estimated with WinBUGS which is an open source Bayesian analysis software tool that uses Markov Chain Monte Carlo method to fit statistical models. Secondly, creep deformation in stress relaxation data has been analyzed. Well performing creep equations have been validated with the observed data. The creep model with the highest goodness of fit among the validated models has been used to estimate probability of exceedance at 0.6% strain level for the steel alloy.

  3. Buckling and Delamination Growth Analysis of Composite Laminates Containing Embedded Delaminations

    Science.gov (United States)

    Hosseini-Toudeshky, H.; Hosseini, S.; Mohammadi, B.

    2010-04-01

    The objective of this work is to study the post buckling behavior of composite laminates, containing embedded delamination, under uniaxial compression loading. For this purpose, delamination initiation and propagation is modeled using the softening behavior of interface elements. The full layer-wise plate theory is also employed for approximating the displacement field of laminates and the interface elements are considered as a numerical layer between any two adjacent layers which delamination is expected to propagate. A finite element program was developed and the geometric non-linearity in the von karman sense is incorporated to the strain/displacement relations, to obtain the buckling behavior. It will be shown that, the buckling load, delamination growth process and buckling mode of the composite plates depends on the size of delamination and stacking sequence of the laminates.

  4. Improved Creep Behavior of a High Nitrogen Nb-Stabilized 15Cr-15Ni Austenitic Stainless Steel Strengthened by Multiple Nanoprecipitates

    Science.gov (United States)

    Ha, Vu The; Jung, Woo Sang; Suh, Jin Yoo

    2011-11-01

    Austenitic stainless steels are expected to be a major material for boiler tubes and steam turbines in future ultra-supercritical (USC) fossil power plants. It is of great interest to maximize the creep strength of the materials without increasing the cost. Precipitation strengthening was found to be the best and cheapest way for increasing the creep strength of such steels. This study is concerned with improving creep properties of a high nitrogen Nb-stabilized 15Cr-15Ni austenitic alloy through introducing a high number of nanosized particles into the austenitic matrix. The addition of around 4 wt pct Mn and 0.236 wt pct N into the 15Cr-15Ni-0.46Si-0.7Nb-1.25Mo-3Cu-Al-B-C matrix in combination with a special multicycled aging-quenching heat treatment resulted in the fine dispersion of abundant quantities of thermally stable (Nb,Cr,Fe)(C,N) precipitates with sizes of 10 to 20 nm. Apart from the carbonitrides, it was found that a high number of coherent copper precipitates with size 40 to 60 nm exist in the microstructure. Results of creep tests at 973 K and 1023 K (700 °C and 750 °C) showed that the creep properties of the investigated steel are superior compared to that of the commercial NF709 alloy. The improved creep properties are attributed to the improved morphology and thermal stability of the carbonitrides as well as to the presence of the coherent copper precipitates inside the austenitic matrix.

  5. Creep Resistant Zinc Alloy

    Energy Technology Data Exchange (ETDEWEB)

    Frank E. Goodwin

    2002-12-31

    This report covers the development of Hot Chamber Die Castable Zinc Alloys with High Creep Strengths. This project commenced in 2000, with the primary objective of developing a hot chamber zinc die-casting alloy, capable of satisfactory service at 140 C. The core objectives of the development program were to: (1) fill in missing alloy data areas and develop a more complete empirical model of the influence of alloy composition on creep strength and other selected properties, and (2) based on the results from this model, examine promising alloy composition areas, for further development and for meeting the property combination targets, with the view to designing an optimized alloy composition. The target properties identified by ILZRO for an improved creep resistant zinc die-casting alloy were identified as follows: (1) temperature capability of 1470 C; (2) creep stress of 31 MPa (4500 psi); (3) exposure time of 1000 hours; and (4) maximum creep elongation under these conditions of 1%. The project was broadly divided into three tasks: (1) Task 1--General and Modeling, covering Experimental design of a first batch of alloys, alloy preparation and characterization. (2) Task 2--Refinement and Optimization, covering Experimental design of a second batch of alloys. (3) Task 3--Creep Testing and Technology transfer, covering the finalization of testing and the transfer of technology to the Zinc industry should have at least one improved alloy result from this work.

  6. Creep Resistant Zinc Alloy

    Energy Technology Data Exchange (ETDEWEB)

    Frank E. Goodwin

    2002-12-31

    This report covers the development of Hot Chamber Die Castable Zinc Alloys with High Creep Strengths. This project commenced in 2000, with the primary objective of developing a hot chamber zinc die-casting alloy, capable of satisfactory service at 140 C. The core objectives of the development program were to: (1) fill in missing alloy data areas and develop a more complete empirical model of the influence of alloy composition on creep strength and other selected properties, and (2) based on the results from this model, examine promising alloy composition areas, for further development and for meeting the property combination targets, with the view to designing an optimized alloy composition. The target properties identified by ILZRO for an improved creep resistant zinc die-casting alloy were identified as follows: (1) temperature capability of 1470 C; (2) creep stress of 31 MPa (4500 psi); (3) exposure time of 1000 hours; and (4) maximum creep elongation under these conditions of 1%. The project was broadly divided into three tasks: (1) Task 1--General and Modeling, covering Experimental design of a first batch of alloys, alloy preparation and characterization. (2) Task 2--Refinement and Optimization, covering Experimental design of a second batch of alloys. (3) Task 3--Creep Testing and Technology transfer, covering the finalization of testing and the transfer of technology to the Zinc industry should have at least one improved alloy result from this work.

  7. Timoshenko beam model for buckling of piezoelectric nanowires with surface effects.

    Science.gov (United States)

    Samaei, Arash Tourki; Bakhtiari, Majid; Wang, Gang-Feng

    2012-03-27

    This paper investigates the buckling behavior of piezoelectric nanowires under distributed transverse loading, within the framework of the Timoshenko beam theory, and in the presence of surface effects. Analytical relations are given for the critical force of axial buckling of nanowires by accounting for the effects of surface elasticity, residual surface tension, and transverse shear deformation. Through an example, it is shown that the critical electric potential of buckling depends on both the surface stresses and piezoelectricity. This study may be helpful in the characterization of the mechanical properties of nanowires and in the calibration of the nanowire-based force sensors.

  8. On the buckling eigenvalue problem

    Energy Technology Data Exchange (ETDEWEB)

    Antunes, Pedro R S, E-mail: pant@cii.fc.ul.pt [Departamento de Matematica, Universidade Lusofona de Humanidades e Tecnologias, Av. do Campo Grande, 376, 1749-024 Lisboa (Portugal); Group of Mathematical Physics of the University of Lisbon, Complexo Interdisciplinar, Av. Professor Gama Pinto 2, P-1649-003 Lisboa (Portugal)

    2011-05-27

    We prove a density result which allows us to justify the application of the method of fundamental solutions to solve the buckling eigenvalue problem of a plate. We address an example of an analytic convex domain for which the first eigenfunction does change the sign and present a large-scale numerical study with polygons providing numerical evidence to some new conjectures.

  9. Combined scleral buckling and phacoemulsification

    Directory of Open Access Journals (Sweden)

    Pukhraj Rishi

    2009-01-01

    Conclusion: Combined scleral buckling and phacoemulsification is a safe and effective procedure that spares the patient the burden of repeated surgeries. It may be considered as a treatment option in selected cases of rhegmatogenous retinal detachment with significant cataract with/without early PVR.

  10. Structure of twisted and buckled bilayer graphene

    Science.gov (United States)

    Jain, Sandeep K.; Juričić, Vladimir; Barkema, Gerard T.

    2017-03-01

    We study the atomic structure of twisted bilayer graphene, with very small mismatch angles (θ ∼ {0.28}0), a topic of intense recent interest. We use simulations, in which we combine a recently presented semi-empirical potential for single-layer graphene, with a new term for out-of-plane deformations, (Jain et al 2015 J. Phys. Chem. C 119 9646) and an often-used interlayer potential (Kolmogorov et al 2005 Phys. Rev. B 71 235415). This combination of potentials is computationally cheap but accurate and precise at the same time, allowing us to study very large samples, which is necessary to reach very small mismatch angles in periodic samples. By performing large scale atomistic simulations, we show that the vortices appearing in the Moiré pattern in the twisted bilayer graphene samples converge to a constant size in the thermodynamic limit. Furthermore, the well known sinusoidal behavior of energy no longer persists once the misorientation angle becomes very small (θ \\lt {1}0). We also show that there is a significant buckling after the relaxation in the samples, with the buckling height proportional to the system size. These structural properties have direct consequences on the electronic and optical properties of bilayer graphene.

  11. Influence of Heat Treatment Condition for the Grain Boundary Serration on Deformation Behavior of Alloy 617 during Creep at 950℃

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Ji Won; Hong, Hyun Uk [Changwon National University, Changwon (Korea, Republic of)

    2015-10-15

    The effect of the heat treatment condition to introduce the grain boundary (GB) serration on the creep properties was investigated at 950℃ in a solid-solution-strengthened Alloy 617. Serrated GBs without carbide at the early stage of slow-cooling were newly observed, and appear to challenge previous models. As the aging temperature for which the specimen was slow-cooled from 1200℃ decreased, the amplitude and the fraction of the serration became higher. The serrated GBs with stable planar M{sub 2}3C{sub 6} carbides caused a fairly long period of a steady-state stage due to their higher resistance to GB cavitation cracking as well as substantial suppression of recrystallization. The very fine and stable intragranular carbides, which precipitated uniformly throughout the serrated specimen aged at 1000 ℃ during the initial stage of creep, were responsible for the further improvement in the creep rupture life (up to 2.8 times longer) by lowering the creep strain rate.

  12. Creep characterization of gels and nonlinear viscoelastic material model

    Science.gov (United States)

    Ishikawa, Kiyotaka; Fujikawa, Masaki; Makabe, Chobin; Tanaka, Kou

    2016-07-01

    In this paper, we examine gel creep behavior and develop a material model for useful and simple numerical simulation of this behavior. This study has three stages and aims: (1) gel creep behavior is examined; (2) the material model is determined and the material constants are identified; and (3) the versatility of the material model and the constants are evaluated. The creep behavior is found to be independent of the initial stress level in the present experiment. Thus, the viscoelastic model proposed by Simo is selected, and its material constants are identified using the results of creep tests. Moreover, from the results of numerical calculations and experiments, it is found that the chosen material model has good reproducibility, predictive performance and high versatility.

  13. CREEP AND CREEP-FATIGUE OF ALLOY 617 WELDMENTS

    Energy Technology Data Exchange (ETDEWEB)

    Wright, Jill; Carroll, Laura; Wright, Richard

    2014-08-01

    The Very High Temperature Reactor (VHTR) Intermediate Heat Exchanger (IHX) may be joined to piping or other components by welding. Creep-fatigue deformation is expected to be a predominant failure mechanism of the IHX1 and thus weldments used in its fabrication will experience varying cyclic stresses interrupted by periods of elevated temperature deformation. These periods of elevated temperature deformation are greatly influenced by a materials’ creep behavior. The nickel-base solid solution strengthened alloy, Alloy 617, is the primary material candidate for a VHTR-type IHX, and it is expected that Alloy 617 filler metal will be used for welds. Alloy 617 is not yet been integrated into Section III of the Boiler and Pressure Vessel Code, however, nuclear component design with Alloy 617 requires ASME (American Society of Mechanical Engineers) Code qualification. The Code will dictate design for welded construction through significant performance reductions. Despite the similar compositions of the weldment and base material, significantly different microstructures and mechanical properties are inevitable. Experience of nickel alloy welds in structural applications suggests that most high temperature failures occur at the weldments or in the heat-affected zone. Reliably guarding against this type of failure is particularly challenging at high temperatures due to the variations in the inelastic response of the constituent parts of the weldment (i.e., weld metal, heat-affected zone, and base metal) [ref]. This work focuses on the creep-fatigue behavior of nickel-based weldments, a need noted during the development of the draft Alloy 617 ASME Code Case. An understanding of Alloy 617 weldments when subjected to this important deformation mode will enable determination of the appropriate design parameters associated with their use. Specifically, the three main areas emphasized are the performance reduction due to a weld discontinuity in terms of the reduced number of

  14. Characteristics of bifurcation and buckling load of space truss in consideration of initial imperfection and load mode

    Institute of Scientific and Technical Information of China (English)

    Su-deok SHON; Seung-jae LEE; Kang-guk LEE

    2013-01-01

    This study investigated characteristics of bifurcation and critical buckling load by shape imperfection of space truss,which were sensitive to initial conditions.The critical point and buckling load were computed by the analysis of the eigenvalues and determinants of the tangential stiffness matrix.The two-free-nodes example and star dome were selected for the case study in order to examine the nodal buckling and global buckling by the sensitivity to the eigen buckling mode and the analyses of the influence,and characteristics of the parameters as defined by the load ratio of the center node and surrounding node,as well as rise-span ratio were performed.The sensitivity to the imperfection of the initial shape of the two-free-nodes example,which occurs due 1o snapping at the critical point,resulted in bifurcation before the limit point due to the buckling mode,and the buckling load was reduced by the increase in the amount of imperfection.The two sensitive buckling patterns of the numerical model are established by investigating the displaced position of the free nodes,and the asymmetric eigenmode greatly influenced the behavior of the imperfection shape whether it was at limit point or bifurcation.Furthermore,the sensitive mode of the two-free-nodes example was similar to the in-extensional basis mechanism of a simplified model.The star dome,which was used to examine the influence among several nodes,indicated that the influence of nodal buckling was greater than that of global buckling as the rise-span ratio was higher.Besides,global buckling is occurred with reaching bifurcation point as the value of load ratio was higher,and the buckling load level was about 50%-70% of load level at limit point.

  15. Artery buckling analysis using a two-layered wall model with collagen dispersion.

    Science.gov (United States)

    Mottahedi, Mohammad; Han, Hai-Chao

    2016-07-01

    Artery buckling has been proposed as a possible cause for artery tortuosity associated with various vascular diseases. Since microstructure of arterial wall changes with aging and diseases, it is essential to establish the relationship between microscopic wall structure and artery buckling behavior. The objective of this study was to developed arterial buckling equations to incorporate the two-layered wall structure with dispersed collagen fiber distribution. Seven porcine carotid arteries were tested for buckling to determine their critical buckling pressures at different axial stretch ratios. The mechanical properties of these intact arteries and their intima-media layer were determined via pressurized inflation test. Collagen alignment was measured from histological sections and modeled by a modified von-Mises distribution. Buckling equations were developed accordingly using microstructure-motivated strain energy function. Our results demonstrated that collagen fibers disperse around two mean orientations symmetrically to the circumferential direction (39.02°±3.04°) in the adventitia layer; while aligning closely in the circumferential direction (2.06°±3.88°) in the media layer. The microstructure based two-layered model with collagen fiber dispersion described the buckling behavior of arteries well with the model predicted critical pressures match well with the experimental measurement. Parametric studies showed that with increasing fiber dispersion parameter, the predicted critical buckling pressure increases. These results validate the microstructure-based model equations for artery buckling and set a base for further studies to predict the stability of arteries due to microstructural changes associated with vascular diseases and aging.

  16. Thermal and Mechanical Buckling Analysis of Hypersonic Aircraft Hat-Stiffened Panels With Varying Face Sheet Geometry and Fiber Orientation

    Science.gov (United States)

    Ko, William L.

    1996-01-01

    Mechanical and thermal buckling behavior of monolithic and metal-matrix composite hat-stiffened panels were investigated. The panels have three types of face-sheet geometry: Flat face sheet, microdented face sheet, and microbulged face sheet. The metal-matrix composite panels have three types of face-sheet layups, each of which is combined with various types of hat composite layups. Finite-element method was used in the eigenvalue extractions for both mechanical and thermal buckling. The thermal buckling analysis required both eigenvalue and material property iterations. Graphical methods of the dual iterations are shown. The mechanical and thermal buckling strengths of the hat-stiffened panels with different face-sheet geometry are compared. It was found that by just microdenting or microbulging of the face sheet, the axial, shear, and thermal buckling strengths of both types of hat-stiffened panels could be enhanced considerably. This effect is more conspicuous for the monolithic panels. For the metal-matrix composite panels, the effect of fiber orientations on the panel buckling strengths was investigated in great detail, and various composite layup combinations offering, high panel buckling strengths are presented. The axial buckling strength of the metal-matrix panel was sensitive to the change of hat fiber orientation. However, the lateral, shear, and thermal buckling strengths were insensitive to the change of hat fiber orientation.

  17. Axial buckling scrutiny of doubly orthogonal slender nanotubes via nonlocal continuum theory

    Energy Technology Data Exchange (ETDEWEB)

    Kiani, Keivan [K.N. Toosi University of Technolog, Tehran (Iran, Islamic Republic of)

    2015-10-15

    Using nonlocal Euler-Bernoulli beam theory, buckling behavior of elastically embedded Doubly orthogonal single-walled carbon nanotubes (DOSWCNTs) is studied. The nonlocal governing equations are obtained. In fact, these are coupled fourth-order integroordinary differential equations which are very difficult to be solved explicitly. As an alternative solution, Galerkin approach in conjunction with assumed mode method is employed, and the axial compressive buckling load of the nanosystem is evaluated. For DOSWCNTs with simply supported tubes, the influences of the slenderness ratio, aspect ratio, intertube free space, small-scale parameter, and properties of the surrounding elastic matrix on the axial buckling load of the nanosystem are addressed. The proposed model could be considered as a pivotal step towards better understanding the buckling behavior of more complex nanosystems such as doubly orthogonal membranes or even jungles of carbon nanotubes.

  18. Size-dependent thermal buckling of heated nanowires with ends axially restrained

    Science.gov (United States)

    Wang, Yu; Wang, Zhi-Qiao; Lv, Jian-Guo

    2014-02-01

    Nanowires (NWs) are being actively explored for applications as nanoscale building blocks of sensors, actuators and nanoelectromechanical systems (NEMS). Temperature changes can induce an axial force within NWs due to the thermal expansion and may lead to buckling. The thermal buckling behaviors of ends-axially-restrained nanowires, subjected to a uniform temperature rise, are studied based on Bernoulli-Euler beam theory including the surface thermoelastic effects. Besides the surface elastic modulus, the influences of surface thermal expansion coefficient are incorporated into the model presented herein to describe size-dependent thermoelastic behaviors of nanowires. The results show that the critical buckling temperature and postbuckling deflection are significantly affected by surface thermoelastic effects and the influences become more prominent as the thickness of nanowire decreases. The corresponding influences of the slenderness ratio are also discussed. This research is helpful not only in understanding the thermal buckling properties of nanowires but also in designing the nanowire-based sensor and thermal actuator.

  19. Size-dependent thermal buckling of heated nanowires with ends axially restrained

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yu [School of Engineering and Technology, China University of Geosciences, Beijing 100083 (China); Key Laboratory on Deep GeoDrilling Technology, Ministry of Land and Resources, China University of Geosciences, Beijing 100083 (China); Wang, Zhi-Qiao, E-mail: zqwang@cugb.edu.cn [School of Engineering and Technology, China University of Geosciences, Beijing 100083 (China); Key Laboratory on Deep GeoDrilling Technology, Ministry of Land and Resources, China University of Geosciences, Beijing 100083 (China); Lv, Jian-Guo [School of Engineering and Technology, China University of Geosciences, Beijing 100083 (China); Key Laboratory on Deep GeoDrilling Technology, Ministry of Land and Resources, China University of Geosciences, Beijing 100083 (China)

    2014-02-01

    Nanowires (NWs) are being actively explored for applications as nanoscale building blocks of sensors, actuators and nanoelectromechanical systems (NEMS). Temperature changes can induce an axial force within NWs due to the thermal expansion and may lead to buckling. The thermal buckling behaviors of ends-axially-restrained nanowires, subjected to a uniform temperature rise, are studied based on Bernoulli–Euler beam theory including the surface thermoelastic effects. Besides the surface elastic modulus, the influences of surface thermal expansion coefficient are incorporated into the model presented herein to describe size-dependent thermoelastic behaviors of nanowires. The results show that the critical buckling temperature and postbuckling deflection are significantly affected by surface thermoelastic effects and the influences become more prominent as the thickness of nanowire decreases. The corresponding influences of the slenderness ratio are also discussed. This research is helpful not only in understanding the thermal buckling properties of nanowires but also in designing the nanowire-based sensor and thermal actuator.

  20. ANALYSIS ON THE MAGNETO-ELASTIC-PLASTIC BUCKLING/SNAPPING OF CANTILEVER RECTANGULAR FERROMAGNETIC PLATES

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    An analysis of buckling/snapping and bending behaviors of magneto-elastic-plastic interaction and coupling for cantilever rectangular soft ferromagnetic plates is presented. Based on the expression of magnetic force from the variational principle of ferromagnetic plates, the buckling and bending theory of thin plates, the Mises yield criterion and the increment theory for plastic deformation, we establish a numerical code to quantitatively simulate the behaviors of the nonlinearly multi-fields coupling problems by the finite element method. Along with the phenomena of buckling/snapping and bending, or the characteristic curve of deflection versus magnitude of applied magnetic fields being numerically displayed, the critical loads of buckling/snapping,and the influences of plastic deformation and the width of plate on these critical loads, the plastic regions expanding with the magnitude of applied magnetic field, as well as the evolvement of deflection configuration of the plate are numerically obtained in a case study.

  1. Circular Functions Based Comprehensive Analysis of Plastic Creep Deformations in the Fiber Reinforced Composites

    Science.gov (United States)

    Monfared, Vahid

    2016-06-01

    Analytically based model is presented for behavioral analysis of the plastic deformations in the reinforced materials using the circular (trigonometric) functions. The analytical method is proposed to predict creep behavior of the fibrous composites based on basic and constitutive equations under a tensile axial stress. New insight of the work is to predict some important behaviors of the creeping matrix. In the present model, the prediction of the behaviors is simpler than the available methods. Principal creep strain rate behaviors are very noteworthy for designing the fibrous composites in the creeping composites. Analysis of the mentioned parameter behavior in the reinforced materials is necessary to analyze failure, fracture, and fatigue studies in the creep of the short fiber composites. Shuttles, spaceships, turbine blades and discs, and nozzle guide vanes are commonly subjected to the creep effects. Also, predicting the creep behavior is significant to design the optoelectronic and photonic advanced composites with optical fibers. As a result, the uniform behavior with constant gradient is seen in the principal creep strain rate behavior, and also creep rupture may happen at the fiber end. Finally, good agreements are found through comparing the obtained analytical and FEM results.

  2. Circular Functions Based Comprehensive Analysis of Plastic Creep Deformations in the Fiber Reinforced Composites

    Science.gov (United States)

    Monfared, Vahid

    2016-12-01

    Analytically based model is presented for behavioral analysis of the plastic deformations in the reinforced materials using the circular (trigonometric) functions. The analytical method is proposed to predict creep behavior of the fibrous composites based on basic and constitutive equations under a tensile axial stress. New insight of the work is to predict some important behaviors of the creeping matrix. In the present model, the prediction of the behaviors is simpler than the available methods. Principal creep strain rate behaviors are very noteworthy for designing the fibrous composites in the creeping composites. Analysis of the mentioned parameter behavior in the reinforced materials is necessary to analyze failure, fracture, and fatigue studies in the creep of the short fiber composites. Shuttles, spaceships, turbine blades and discs, and nozzle guide vanes are commonly subjected to the creep effects. Also, predicting the creep behavior is significant to design the optoelectronic and photonic advanced composites with optical fibers. As a result, the uniform behavior with constant gradient is seen in the principal creep strain rate behavior, and also creep rupture may happen at the fiber end. Finally, good agreements are found through comparing the obtained analytical and FEM results.

  3. 防腐混凝土梁长期力学性能试验研究%THE STUDY ON CREEP BEHAVIOR OF FRP REBAR REINFORCED ANTISEPTIC CONCRETE BEAM

    Institute of Scientific and Technical Information of China (English)

    余启明; 吴卫国; 李军向; 晏石林

    2009-01-01

    FRP rural resin concrete which has extensive application prospect is a kind of anti-corrosive new en-gineering material. Although it's stronger in compression than cementitious concrete, its tension behavior is weak, the reinforcement of polymer concrete beams in the tension zone with puhruded profiles made of resin and glass fibers are a good compromise between strength and stiffness. In this paper, firstly the experience has performed about the bending and creep characteristic of non-FRP reinforced furan resin concrete beam and FRP reinforced furan concrete beam, the creep curves are gained of the beams under different loads by four-point bending tests method, analysis is carried on the viscoelasticity nature, the result shows that FRP not only enhances the furan resin concrete beam's ini-tial stiffness and strength, but also obviously reduces the creep strain of the beam. Secondly the creep model varia-bles are determined through the least square method, the bending creep power law model are separately built of non-FRP reinforced furan resin concrete beam and FRP reinforced furan concrete beam,which is the basis of estimation of material's long term mechanics performance, and also has important project practical value to the FRP furan resin concrete structure design.%玻璃钢(FRP)筋防腐混凝土是一种强度高、全方位耐腐蚀的新型工程材料,具有十分广泛的应用前景.本文先对防腐混凝土梁采用四点弯曲试验方法,对FRP筋加强混凝土梁的弯曲长期力学特性进行了试验研究与分析,得到了梁在不同荷载水平作用下的蠕变曲线.结果表明,FRP筋不仅提高了防腐混凝土梁的初始刚度和强度,且明显降低了梁的蠕变变形.最后,运用最小二乘法确定蠕变模型参数,分别建立了防腐混凝土粱和FRP筋加强防腐混凝土梁的弯曲蠕变幂律模型,为估计材料的长期力学性能提供依据,对FRP筋防腐混凝土结构设计具有重要的价值.

  4. 钢管混凝土轴压构件徐变有限元研究%Finite Element Analysis on the Creep Behavior of Axially-Compressed Concrete Filled Steel Tube Members

    Institute of Scientific and Technical Information of China (English)

    冯伟; 查晓雄

    2011-01-01

    The use of concrete filled steel tubular (CFST) structures in high-rise building can well solve the conflict between the long time of concrete hardening and the requirement of fast construction speed, and make full use of the strength and stiffness of the hollow steel tube. But it also brings such problems, during the construction process of the structure, the CFST members suffered gradually increased long-term load, which makes concrete creep sustainably developing, concrete unloading. internal forces re-distributing, resulting in lower load-carrying capacity of the CFST members. By adopting DirichLet series in the concrete creep model, this paper applied the nonlinear FEM software ABAQUS in simulating the creep process of CFST members and testing their load-carrying capacity; the FEM results are validated to be reliable and accurate. A parametric study is then conducted to investigate the creep behavior of CFST members. It is concluded that the initial stress can be introduced to roughly estimate the effect of creep on axially load-carrying capacity.%在高层和超高层建筑中采用钢管混凝土结构,可充分利用空钢管所具有的强度和刚度,并能较好地解决混凝土硬化时间较长与施工速度之间的矛盾.但由此也会带来这样的问题,即在结构施工过程中,构件所受长期荷载随施工过程逐渐增加,徐变持续发展,混凝土卸载,内力重新分布,导致构件稳定承载力降低.本文运用DirichLet级数建立管内混凝土徐变模型,并应用非线性有限元软件ABAQUS对钢管混凝土徐变以及承载力进行了有限元计算,较好地模拟了钢管混凝土的徐变过程.本文回归分析了钢管混凝土的徐变性质,并认为可以用初应力的方法粗略估计徐变构件对承载力的影响.

  5. Creep-rupture reliability analysis

    Science.gov (United States)

    Peralta-Duran, A.; Wirsching, P. H.

    1985-01-01

    A probabilistic approach to the correlation and extrapolation of creep-rupture data is presented. Time temperature parameters (TTP) are used to correlate the data, and an analytical expression for the master curve is developed. The expression provides a simple model for the statistical distribution of strength and fits neatly into a probabilistic design format. The analysis focuses on the Larson-Miller and on the Manson-Haferd parameters, but it can be applied to any of the TTP's. A method is developed for evaluating material dependent constants for TTP's. It is shown that optimized constants can provide a significant improvement in the correlation of the data, thereby reducing modelling error. Attempts were made to quantify the performance of the proposed method in predicting long term behavior. Uncertainty in predicting long term behavior from short term tests was derived for several sets of data. Examples are presented which illustrate the theory and demonstrate the application of state of the art reliability methods to the design of components under creep.

  6. Creep of Two-Phase Microstructures for Microelectronic Applications

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, Heidi Linch [Univ. of California, Berkeley, CA (United States)

    1998-12-01

    The mechanical properties of low-melting temperature alloys are highly influenced by their creep behavior. This study investigates the dominant mechanisms that control creep behavior of two-phase, low-melting temperature alloys as a function of microstructure. The alloy systems selected for study were In-Ag and Sn-Bi because their eutectic compositions represent distinctly different microstructure.” The In-Ag eutectic contains a discontinuous phase while the Sn-Bi eutectic consists of two continuous phases. In addition, this work generates useful engineering data on Pb-free alloys with a joint specimen geometry that simulates microstructure found in microelectronic applications. The use of joint test specimens allows for observations regarding the practical attainability of superplastic microstructure in real solder joints by varying the cooling rate. Steady-state creep properties of In-Ag eutectic, Sn-Bi eutectic, Sn-xBi solid-solution and pure Bi joints have been measured using constant load tests at temperatures ranging from O°C to 90°C. Constitutive equations are derived to describe the steady-state creep behavior for In-Ageutectic solder joints and Sn-xBi solid-solution joints. The data are well represented by an equation of the form proposed by Dom: a power-law equation applies to each independent creep mechanism. Rate-controlling creep mechanisms, as a function of applied shear stress, test temperature, and joint microstructure, are discussed. Literature data on the steady-state creep properties of Sn-Bi eutectic are reviewed and compared with the Sn-xBi solid-solution and pure Bi joint data measured in the current study. The role of constituent phases in controlling eutectic creep behavior is discussed for both alloy systems. In general, for continuous, two-phase microstructure, where each phase exhibits significantly different creep behavior, the harder or more creep resistant phase will dominate the creep behavior in a lamellar microstructure. If a

  7. Creep in refractory materials; Fluencia en materiales refractarios

    Energy Technology Data Exchange (ETDEWEB)

    Tomba Martinez, A. G.; Luz, A. P.; Pandolfelli, V. C.

    2013-10-01

    Refractory materials are widely used in various industrial fields due to their outstanding properties and performance in aggressive environments. However, although creep resistance is one of the most important properties for the selection of these materials, few researches were carried out focused on the fundamentals and technological understanding of their performance at high temperatures. In this context, this work addresses: 1) the creep mechanisms, 2) the mathematical models proposed for the analysis and to forecast the creep deformation at high temperature, 3) technical procedures and experimental testing, and 4) a critical analysis of some basic and practical aspects considering the literature available on this issue. Based on the collected information, mathematical models (such as the Projection concept) were considered as a powerful tool for the prediction of the refractories creep behavior, helping to identify the main creep mechanisms in these materials and to induce the development of optimized compositions able to attend the end-users requirements. (Author)

  8. CREEP BEHAVIOR OF TWO KINDS OF HR3C HEAT RESISTANT STEELS BASED ON STRESS RELAXATION TESTS%应力松弛方法研究2种HR3C耐热钢的高温蠕变行为

    Institute of Scientific and Technical Information of China (English)

    曹铁山; 方旭东; 程从前; 赵杰

    2014-01-01

    Rupture life is a main property for a material using at high-temperature condition.Usually,the rupture life is gained from creep rupture test.As creep and stress relaxation are two main behaviors for a material served in high-temperature environment,it is important to work out the interrelationship through which one of the two behaviors can be deduced from the other one.Recently,a number of researchs have taken stress relaxation test to replace creep rupture test on studying the creep behavior,and furthermore predicting the rupture life and the stress relaxation test is proved to be superior to the traditional creep rupture test for its short time,small at damage,abundant of information and so on.In this work,the stress relaxation test was used to analyze the creep behavior of two HR3C heat resistant steels with different grain sizes.Additionally,considering the change of microstructure during serve period,the aged HR3C steel was used to compare with as-received HR3C steel for studying the aging effects on the creep behavior.Furthermore,the creep behavior was correlated to their microstructure characteristics.The result was shown that the creep behaviors of two HR3C heat resistant steels varied significantly in spite of their similarity in chemical composition.The coarse grained HR3C steel had lower creep rate,larger stress exponent,greater activation energy and higher creep resistance than that of fine grained HR3C steel for both as-received one and aged one.The long-term aging process damaged the microstructures of two HR3C steels,increased aged HR3C steel's creep rate,lowered stress exponent and activation energy and reduced creep resistance.And the damaging effects on the coarse grained HR3C steel were larger than that on fine grained HR3C steel,which meant the coarse grained HR3C steel had much more stable creep resistance than that of fine grained HR3C steel.%采用应力松弛方法研究了2种不同晶粒大小HR3C耐热钢的初始态试样和时效态

  9. Limit Load and Buckling Analysis for Assessing Hanford Single-Shell Tank Dome Structural Integrity - 12278

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Ken I.; Deibler, John E.; Karri, Naveen K.; Pilli, Siva P. [Pacific Northwest National Laboratory, Richland, Washington 99352 (United States); Julyk, Larry J. [M and D Professional Services, Inc., Richland, Washington 99352 (United States)

    2012-07-01

    dome, so the penetration does reduce the concentrated limit load somewhat. However, the safety factors comparing the limit loads to the maximum allowable applied loads remain well above the required value of 3.0. The buckling analysis method accounts for the geometric imperfections, concrete creep, cracking and reinforcements, and concrete plasticity in determining the allowable buckling load limits. The method was demonstrated in this paper for the evaluation of a tank before and after a penetration is added in the dome center. Finite element buckling models were used to accurately calculate the linear critical buckling loads. The models showed that adding the penetration reduces the linear critical buckling load by only 2.5%. Bounding cases also showed that the possible range of soil support on the walls does not significantly affect the dome buckling loads. Buckling models of the full 360 deg. dome also showed that the dome is more resistant to buckling when the load is offset than when it is positioned over the center. These limit load and buckling analysis methods are being used at the Hanford site to assess the tank loads that can be safely applied during future waste retrieval activities. (authors)

  10. Research on Flexural Creep Behavior of Glass Fiber Reinforced Vinyl Ester Resin Composites%玻纤增强乙烯基树脂复合材料弯曲蠕变行为研究

    Institute of Scientific and Technical Information of China (English)

    张兴刚; 张用兵

    2013-01-01

    树脂基复合材料具有粘弹性,长期在外力作用下会发生蠕变现象,导致复合材料的刚度和强度都发生衰退,致使复合材料结构失去继续承载能力。由于复合材料蠕变研究多集中在拉伸状况下,缺少足够的弯曲蠕变数据,难以进行复合材料结构的可靠性设计。针对玻纤增强乙烯基树脂复合材料进行了弯曲蠕变测试,分析了弯曲蠕变后复合材料试样的力学性能及翘曲变形,并根据时间-挠度曲线探讨了蠕变极限。结果显示,该复合材料在20天左右基本可以达到蠕变平衡,且其蠕变性能优异。%As the viscoelastic nature of fiber reinforced plastic, creep may occur under long term ex-ternal force, then the stiffness and strength of composite structures decrease gradually, and the whole structural system will fail at last. For many years, creep study on fiber reinforced plastic is mainly concerned with tensile behavior, but less research is done on the flexural creep behavior. Because of the insufifciency of storage data, it is dififcult to study the reliability of composites structures in long-term use of lfexure loadings. In this paper, by means of testing lfexural lfexibility change at different times, the lfexural creep behavior by three-point loading of glass if-ber reinforced vinyl ester resins composites is studied. The results show that lfexural delfection changes obviously at the beginning stage of applying lfexural loading, and the change of lfexural delfection is decreased with the prolong of time.

  11. Creep of fibrous composite materials

    DEFF Research Database (Denmark)

    Lilholt, Hans

    1985-01-01

    Models are presented for the creep behaviour of fibrous composite materials with aligned fibres. The models comprise both cases where the fibres remain rigid in a creeping matrix and cases where the fibres are creeping in a creeping matrix. The treatment allows for several contributions to the cr......Models are presented for the creep behaviour of fibrous composite materials with aligned fibres. The models comprise both cases where the fibres remain rigid in a creeping matrix and cases where the fibres are creeping in a creeping matrix. The treatment allows for several contributions...... such as Ni + W-fibres, high temperature materials such as Ni + Ni3Al + Cr3C2-fibres, and medium temperature materials such as Al + SiC-fibres. For the first two systems reasonable consistency is found for the models and the experiments, while for the third system too many unquantified parameters exist...

  12. Creep Behavior of Frozen Sand.

    Science.gov (United States)

    1981-06-01

    temperature and stress range. There was a 2strong stress dependance to S (r =0.95) for saturated Manchester Fine Sand which does not agree with RPT. The...Curves at High Stress 161 Ratio D/Du = 0.505 for Frozen HF’S at w=10% IV-20 Minimum Strain Rate Dependance on Stress 162 Ratio for Frozen MFS IV-21 Minimum...Strain Rate Dependance on Relative 163 Density for Frozen MFS IV-22 Temperature Stage Test on Frozen Saturated 164 MFS under a Load of D=9.24MPa Fig

  13. Steady state creep of Ni-8YSZ substrates for application in solid oxide fuel and electrolysis cells

    Science.gov (United States)

    Wei, J.; Malzbender, J.

    2017-08-01

    Steady state creep was characterized for Ni-8YSZ solid oxide fuel/electrolysis cell (SOFC/SOEC) substrate material. Intrinsic and extrinsic factors affecting creep behavior were assessed, such as compositional ratio, porosity and mechanical loading configuration. Mechanical tests were supported by analytical and numerical calculations. The results indicated a diffusion-dominated creep mechanism under both compressive and tensile creep conditions. Creep appeared to be dominated by the ceramic phase. Porosity significantly reduced creep resistance. The activation energy was discussed based on loading configuration, temperature and porosity.

  14. Creep behavior of plasma carburized Ti-6Al-4V alloy; Comportamento em fluencia da liga Ti-6Al-4V carbonetada por plasma

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Veronica Mara Cortez Alves de; Barboza, Miguel Justino Ribeiro; Silva, Mariane Capellari Leite da; Pinto, Catia Gisele; Suzuki, Paulo Atsushi [Universidade de Sao Paulo (EEL/USP), Lorena, SP (Brazil). Escola de Engenharia; Reis, Danieli Aparecida Pereira; Piorino Neto, Francisco [Instituto de Aeronautica e Espaco (IAE/DCTA), Sao Jose dos Campos, SP (Brazil); Machado, Joao Paulo B. [Instituto Nacional de Pesquisas Espaciais (INPE), Sao Jose dos Campos, SP (Brazil)

    2010-07-01

    This paper aims to evaluate the effect of plasma carburizing on the Ti-6Al-4V alloy submitted to creep tests. The results showed that the alloy Ti-6Al-4V had a hardness of 334 ± 18 HV. After treatment thermochemical by plasma, was observed the formation of a layer of average thickness of 1,5 μm and hardness of 809 ± 79 HV due to the presence of TiC phase identified by X-ray diffraction. The treatment increased the values of average roughness of 1,28 to 2,02 μm. The creep properties of carburized specimens were improved in comparison with those of the uncarburized Ti-6Al-4V alloy. (author)

  15. Biaxial thermal creep of Alloy 617 An Alloy 230 for VHTR applications

    Energy Technology Data Exchange (ETDEWEB)

    Mo, Kun; Lv, Wei; Tung, Hsiao-Ming; Yun, Di; Miao, Yinbin; Lan, Kuan-Che; Stubbins, James F.

    2016-07-01

    In this study, we employed pressurized creep tubes to investigate the biaxial thermal creep behavior of Inconel 617 (alloy 617) and Haynes 230 (alloy 230). Both alloys are considered to he the primary candidate structural materials for very high-temperature reactors (VITITRs) due to their exceptional high-temperature mechanical properties. The current creep experiments were conducted at 900 degrees C for the effective stress range of 15-35 MPa. For both alloys, complete creep strain development with primary, secondary, and tertiary regimes was observed in all the studied conditions. Tertiary creep was found to he dominant over the entire creep lives of both alloys. With increasing applied creep stress, the fraction of the secondary creep regime decreases. The nucleation, diffusion, and coarsening of creep voids and carbides on grain boundaries were found to be the main reasons for the limited secondary regime and were also found to be the major causes of creep fracture. The creep curves computed using the adjusted creep equation of the form epsilon= cosh 1(1 rt) + P-sigma ntm agree well with the experimental results for both alloys at die temperatures of 850-950 degrees C.

  16. A Research Status on High-Temperature Creep of Alloy 617 for Use in VHTR System

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Woo-Gon; Park, Jae-Young; Kim, Eung-Seon; Kim, Yong-Wan; Kim, Min-Hwan [KAERI, Daejeon (Korea, Republic of); Kim, Seon-Jin [Pukyong National Univ., Busan (Korea, Republic of)

    2016-05-15

    In this study, a research status on creep works of Alloy 617 conducting at KAERI was introduced and summarized. Various experimental creep data and creep constants obtained in the air/helium environments and base/weld metals were presented and discussed using various creep equations and parameters. The draft Code Case is a modification from ASME Section III Subsection NH that was put forth by a special task force of the ASME subgroup that deals with elevated temperature design. The primary intended application of the draft Code Case is a VHTR. Presently, various creep data for Alloy 617 are being accumulated through Generation-IV forum (GIF) Material Handbook Database of a next-generation nuclear plant research and development. As per this, a new Alloy 617 Code Case is planned to be approved by 2017. However, to do so, various creep data and creep constants in air/helium environments, and base/weld metals etc. should be obtained to help draft the new Code Case, and creep behavior should be investigated through systematic analysis of a wide range of creep temperature and stress conditions. Using various creep equations and parameters, the creep constants were determined for design use of Alloy 617. The stress of the He environment was more reduced than that of the air one. As the stress increases, the creep rate of WM was significantly lower than that of BM. The reason for this was that the rupture elongation of WM was largely reduced compared with that of BM.

  17. Anisotropia no comportamento à fluência de cerâmicas à base de Si3N4 prensadas à quente Creep behavior anisotropy of hot pressed Si3N4 based ceramics

    Directory of Open Access Journals (Sweden)

    C. Santos

    2005-06-01

    Full Text Available Nesse trabalho foi estudada a anisotropia no comportamento à fluência de cerâmicas de Si3N4 prensadas a quente. Quatro tipos de cerâmicas à base de Si3N4 foram desenvolvidas, utilizando-se Al2O3-CRE2O3 ou AlN e CRE2O3 como aditivos, em frações volumétricas de 5 e 20%. CRE2O3 é um óxido misto de ítrio e terras raras produzido na FAENQUIL. As misturas de pós foram submetidas à prensagem uniaxial a quente, a 1750 °C - 20 MPa. As amostras sinterizadas apresentaram fases cristalinas e microestruturas distintas, e foram submetidas a ensaios por compressão a 1300 °C, sob tensão de 300 MPa. Corpos de prova foram confeccionados nos planos paralelo e perpendicular ao eixo de prensagem a quente, e as taxas de fluência para ambos os planos foram obtidas e correlacionadas. Os resultados demonstraram que as amostras confeccionadas no plano perpendicular ao eixo de prensagem a quente, sofreram maiores deformações que as amostras do plano paralelo. Esse comportamento é devido à orientação dos grãos alinhados com o eixo de aplicação de carga compressiva durante os ensaios de fluência.In this work the anisotropy of the creep behavior in hot pressed Si3N4 ceramics was evaluated. Four different Si3N4 ceramics were developed, using Al2O3-CRE2O3 or AlN e CRE2O3 as sintering aids. Specimens were hot pressed at 1750 °C - 20 MPa. The sintered specimens show different crystalline phases and microstructures, and were submitted to compressive creep tests at 1300 °C and stress of 300 MPa. Specimens in the parallel and perpendicular plane to the hot pressing axis were tested and the creep rates and strain were correlated as a function to the plane analyzed. The results show the influence of anisotropy on the creep behavior, related to the orientation of the grains, activating the rotation of the grains by viscous flow of the intergranular phase.

  18. Tailored Buckling Microlattices as Reusable Light-Weight Shock Absorbers.

    Science.gov (United States)

    Frenzel, Tobias; Findeisen, Claudio; Kadic, Muamer; Gumbsch, Peter; Wegener, Martin

    2016-07-01

    Structures and materials absorbing mechanical (shock) energy commonly exploit either viscoelasticity or destructive modifications. Based on a class of uniaxial light-weight geometrically nonlinear mechanical microlattices and using buckling of inner elements, either a sequence of snap-ins followed by irreversible hysteretic - yet repeatable - self-recovery or multistability is achieved, enabling programmable behavior. Proof-of-principle experiments on three-dimensional polymer microstructures are presented.

  19. Evaluation of microstructure and creep damage in high-Cr ferritic steel welds

    Institute of Scientific and Technical Information of China (English)

    Masaaki TABUCHI; Hiromichi HONGO

    2011-01-01

    11Cr-0.4Mo-2W-CuVNb steel (ASME Gr.122) is used for boiler components in ultrasupercritical (USC) thermal power plants. The creep strength of high-Cr steel welds decreases due to the formation of Type Ⅳ creep damage in the heat-affected zone (HAZ) during long-term use at high temperatures. In the present study, the processes and mechanisms of Type Ⅳ creep damage were elucidated by investigating the long-term creep strength, microstructure and damage behavior of Gr.122 steel welds.Creep tests using thick welded joints were interrupted at several time steps, and the initiation, evolution and distribution of creep damage were measured. It was found that the formation and growth of creep damage was suppressed during the steadystate stage; creep voids formed at 0.5 of life, and coalesced to form a crack after 0.9of life. Type Ⅳ creep damage was mostly observed in the area about 30% below the surface of the plate. Differences in creep damage behavior between Gr.122 and Gr.91 steel welds were examined. Experimental creep damage distribution was compared with computed versions using the finite element method and damage mechanics.

  20. Developing Process of Negative Creeping Discharge along Aerial Insulated Wire

    Science.gov (United States)

    Nishi, Toshiyuki; Hanaoka, Ryoichi; Takata, Shinzo

    When a lightning occurs at the neighborhood of high voltage aerial distribution lines, the overvoltage due to the inductive lightning surge invades to the central line of the insulated wire. Because of the insulated wire is supported by the insulator and the binding wire at the electric light pole, the creeping discharges develop along the wire surface from the free end of the binding wire, just after a flashover of the insulator at the wire supporting point. These creeping discharges give rise to the disaster near the wire supporting point including the punch-through breakdown of wire when the weak points such as pin-holes exist in the wire insulator. To prevent these accidents, it is important to understand the behavior of creeping discharges at the insulated wire surface originating in the lightning strike. Positive and negative creeping discharges reveal the distinctive aspect by the polarities of the inductive lightning surges. In the previous paper, we have clarified the developing process of positive creeping discharge based on the data obtained from an image converter camera. In this paper, we report the developing process of negative creeping discharge. Complicated behavior of negative creeping discharge is clarified using an image converter camera and its process is discussed.

  1. Elastic buckling strength of corroded steel plates

    Indian Academy of Sciences (India)

    Ahmad Rahbar-Ranji

    2013-02-01

    Corrosion makes structures more vulnerable to buckling and yielding failures. It is common practice to assume a uniform thickness reduction for general corrosion. To estimate the remaining strength of corroded structures, typically a much higher level of accuracy is required, since the actual corroded structures have irregular surfaces. Elastic buckling of simply supported rectangular corroded plates are studied with one- and both-sided irregular surfaces. Eigenvalue analysis by using finite element method (FEM) is employed for computing Euler stress. The influence of various geometric and corrosion characteristics are investigated and it is found that the aspect ratio of the plate, the average thickness diminution, the standard deviation of thickness diminution and the amount of corrosion loss have influence on the reduction of buckling strength of the corroded plates. Buckling strength of one- and both-sided corroded plates are the same. In plates with low value of aspect ratio, reduction of buckling strength is negligible. Reduction of buckling strength is more prominent in plates with higher aspect ratio. Reduction of buckling strength is very sensitive to the amount of corrosion loss; the higher the amount of corrosion loss, the more reduction of buckling strength. Reduction of buckling strength is less sensitive to the standard deviation of thickness diminution.

  2. Transient effects in friction fractal asperity creep

    CERN Document Server

    Goedecke, Andreas

    2013-01-01

    Transient friction effects determine the behavior of a wide class of mechatronic systems. Classic examples are squealing brakes, stiction in robotic arms, or stick-slip in linear drives. To properly design and understand mechatronic systems of this type, good quantitative models of transient friction effects are of primary interest. The theory developed in this book approaches this problem bottom-up, by deriving the behavior of macroscopic friction surfaces from the microscopic surface physics. The model is based on two assumptions: First, rough surfaces are inherently fractal, exhibiting roughness on a wide range of scales. Second, transient friction effects are caused by creep enlargement of the real area of contact between two bodies. This work demonstrates the results of extensive Finite Element analyses of the creep behavior of surface asperities, and proposes a generalized multi-scale area iteration for calculating the time-dependent real contact between two bodies. The toolset is then demonstrated both...

  3. The elastic buckling of super-graphene and super-square carbon nanotube networks

    Energy Technology Data Exchange (ETDEWEB)

    Li Ying; Qiu Xinming [AML, Department of Engineering Mechanics, School of Aerospace, Tsinghua University, 100084 Beijing (China); Yin Yajun, E-mail: yinyj@tsinghua.edu.c [AML, Department of Engineering Mechanics, School of Aerospace, Tsinghua University, 100084 Beijing (China)] [Division of Mechanics, Nanjing University of Technology, 210009 Nanjing (China); Yang Fan [AML, Department of Engineering Mechanics, School of Aerospace, Tsinghua University, 100084 Beijing (China); Fan Qinshan [Division of Mechanics, Nanjing University of Technology, 210009 Nanjing (China)

    2010-04-05

    The super-graphene (SG) and super-square (SS) carbon nanotube network are built by the straight single-walled carbon nanotubes and corresponding junctions. The elastic buckling behaviors of these carbon nanotube networks under different boundary conditions are explored through the molecular structural mechanics method. The following results are obtained: (a) The critical buckling forces of the SG and SS networks decrease as the side lengths or aspect ratios of the networks increase. The continuum plate theory could give good predictions to the buckling of the SS network but not the SG network with non-uniform buckling modes. (b) The carbon nanotube networks are more stable structures than the graphene structures with less carbon atoms.

  4. 玻纤增强阻燃PBT长期弯曲蠕变行为预测%Long-term Flexural Creep Behavior Prediction of GF-reinforced Flame Retardant PBT

    Institute of Scientific and Technical Information of China (English)

    陈大华; 吴博; 雷彩红

    2011-01-01

    The short term creep data of glass-fiber reinforced flame retardant poly (butylene terephthalate) (PBT-RG301) was studied under different stress using universal testing machine. The long term creep behavior was predicted based on time-stress superposition (TSS) principle, Burgers model and Findley power law. It was found that using TSS principle, the creep value up to 104 h could be predicted. Within experimental time of 4 000 s, the predicted results from Burgers model and Findley power law were in good agreement with the experimental results. The strain values under long time of 10 000h predicted based on Burgers model were far larger than those based on TSS principle and Findley power law, which was further proved by experimental results within 14 h.%采用万能电子拉力机测试了不同应力下玻纤增强阻燃PBT(PBT-RG301)的短期蠕变数据,并采用时间应力等效原理、Burgers模型以及Findley指数定律预测了长期蠕变行为.结果发现:依据时间应力等效原理可预测10000h后体系的蠕变数值,在4000s实验时间内Burgers模型和Findley指数定律均可很好的拟合实验结果,但Burgers模型预测的长期蠕变数据高于Findley指数定律和时间应力等效原理预测数值,实验时间14h的跟踪数据也证实了该结果.

  5. Creep of timber joints

    NARCIS (Netherlands)

    Van de Kuilen, J.W.G.

    2008-01-01

    A creep analysis has been performed on nailed, toothed-plates and split-ring joints in a varying uncontrolled climate. The load levels varied between 30% and 50% of the average ultimate short term strength of these joints, tested in accordance with ISO 6891. The climate in which the tests were

  6. Creep Feeding Beef Calves

    OpenAIRE

    2005-01-01

    Creep feeding is the managerial practice of supplying supplemental feed (usually concentrates) to the nursing calf. Milk from a lactating beef cow furnishes only about 50 percent of the nutrients that a 3-4 month-old calf needs for maximum growth.

  7. Strain rate sensitivity of nanoindentation creep in an AlCoCrFeNi high-entropy alloy

    Science.gov (United States)

    Jiao, Z. M.; Wang, Z. H.; Wu, R. F.; Qiao, J. W.

    2016-09-01

    Creep behaviors of an AlCoCrFeNi high-entropy alloy with the body-centered cubic structure were investigated by nanoindentation. The enhanced strain gradient induced by higher strain rate leads to decreased strain rate sensitivity during creep process. The present alloy exhibits excellent creep resistance, mainly due to its large entropy of mixing and highly distorted lattice structure.

  8. Estimating the creep strain to failure of PP at different load levels based on short term tests and Weibull characterization

    Directory of Open Access Journals (Sweden)

    L. M. Vas

    2012-12-01

    Full Text Available The short and long term creep behavior is one of the most important properties of polymers used for engineering applications. In order to study this kind of behavior of PP tensile and short term creep measurements were performed and analyzed using long term creep behavior estimating method based on short term tensile and creep tests performed at room temperature, viscoelastic behavior, and variable transformations. Applying Weibull distribution based approximations for the measured curves predictions for the creep strain to failure depending on the creep load were determined and the parameters were found by fitting the measurements. The upper, mean, and lower estimations as well as the confidence interval for the means give a possibility for designers' calculations at arbitrary creep load levels.

  9. Creep behaviour and creep mechanisms of normal and healing ligaments

    Science.gov (United States)

    Thornton, Gail Marilyn

    Patients with knee ligament injuries often undergo ligament reconstructions to restore joint stability and, potentially, abate osteoarthritis. Careful literature review suggests that in 10% to 40% of these patients the graft tissue "stretches out". Some graft elongation is likely due to creep (increased elongation of tissue under repeated or sustained load). Quantifying creep behaviour and identifying creep mechanisms in both normal and healing ligaments is important for finding clinically relevant means to prevent creep. Ligament creep was accurately predicted using a novel yet simple structural model that incorporated both collagen fibre recruitment and fibre creep. Using the inverse stress relaxation function to model fibre creep in conjunction with fibre recruitment produced a superior prediction of ligament creep than that obtained from the inverse stress relaxation function alone. This implied mechanistic role of fibre recruitment during creep was supported using a new approach to quantify crimp patterns at stresses in the toe region (increasing stiffness) and linear region (constant stiffness) of the stress-strain curve. Ligament creep was relatively insensitive to increases in stress in the toe region; however, creep strain increased significantly when tested at the linear region stress. Concomitantly, fibre recruitment was evident at the toe region stresses; however, recruitment was limited at the linear region stress. Elevating the water content of normal ligament using phosphate buffered saline increased the creep response. Therefore, both water content and fibre recruitment are important mechanistic factors involved in creep of normal ligaments. Ligament scars had inferior creep behaviour compared to normal ligaments even after 14 weeks. In addition to inferior collagen properties affecting fibre recruitment and increased water content, increased glycosaminoglycan content and flaws in scar tissue were implicated as potential mechanisms of scar creep

  10. Creep of metal-type organic compounds. 3: Friction stress models for creep in particle-hardened systems

    Energy Technology Data Exchange (ETDEWEB)

    Davies, G.C.; Jones, D.R.H. [Univ. of Cambridge (United Kingdom). Engineering Dept.

    1996-08-15

    The effect of a dispersed phase of small, hard particles on the creep behavior of two plastic crystals, camphene and succinonitrile, is investigated experimentally. Three models describing the creep deformation of a material containing hard particles are compared to the experimental data. Previous work has considered the particles to result in a constant friction stress which opposes creep deformation. The experimental results for plastic crystals are shown to be equally consistent with a model in which the friction stress is a linear function of the applied stress.

  11. 元素Re对镍基单晶合金中温蠕变行为的影响%Influence of element Re on intermediate temperature creep behavior of single crystal nickel-base superalloy

    Institute of Scientific and Technical Information of China (English)

    田素贵; 舒德龙; 曾征; 刘臣; 郭忠革

    2013-01-01

    通过对有/无元素Re合金进行蠕变曲线测定及组织形貌观察,研究了元素Re对镍基单晶合金中温蠕变行为的影响.结果表明:与无Re合金相比,4.5% Re合金在中温/高应力条件下具有良好的蠕变抗力.蠕变期间无Re合金中的γ'相转变成串状,而4.5Re合金中的γ'相仍保持立方体形貌,有/无元素Re合金在中温蠕变期间的变形机制均为超位错剪切γ'相,切入γ'相的超位错可在{111}面滑移,或在{111}面分解形成{112}超肖克莱不全位错+(SISF)的位错组态,抑制其交滑移;其中,4.5% Re合金中切入Y'相的超位错可由{111}面交滑移至(100)面,形成K-W锁,是使合金具有良好蠕变抗力的重要原因之一.%Influence of element Re on intermediate temperature creep behavior of the single crystal nickel-base superalloy was studied by means of creep curve measurement and microstructure observation.The results show that compared to free-Re superalloy,4.5% Re superalloy exhibits a better creep resistance under the conditions of medium temperature and high stress.During creep at intermediate temperature,the cubical γ' phase in free-Re superalloy is transformed into the bunch-like structure,and large numbers of γ' phase in 4.5% Re superalloy keep still the cubical configuration.The deformation mechanisms of the free/with Re superalloys during creep are that the slipping of (1/2) dislocations is activated in the γmatrix channels and super-dislocations shear into the γ' phase,and the super-dislocations shearing into the γ' phase both slip on {111} planes and decompose to form the configuration of (1/3) superShockleys partials plus the stacking fault,which may restrain the cross-slipping of dislocations.Therein,the super-dislocations shearing into the γ' phase in 4.5% Re superalloy may cross slip from { 111} to {100} planes to form K-W locks which may restrain the slipping of dislocations due to the non-plane core structure of them,this is

  12. Accurate stress analysis on rigid central buckle of Ions-span suspension bridges based on submodel method

    Institute of Scientific and Technical Information of China (English)

    WANG Hao; LI AiQun; GUO Tong; MA Shuang

    2009-01-01

    Runyang Suspension Bridge (RSB) with the main span of 1490 m is the longest bridge in China and the third longest one in the world. In this bridge the rigid central buckle is employed for the first time in the mid-span of the suspension bridge in China. For such a super-long-span bridge, the traditional finite element (FE) modeling technique and stress analysis methods obviously cannot satisfy the needs of conducting accurate stress analysis on the central buckle. In this paper, the submodel method is introduced and for the first time used in analyzing the stresses of the central buckle. After an accurate FE submodel of the central buckle was specially established according to the analysis results from the whole FE model, the connection technique between the two-scale FE models was realized and the accurate stresses of the central buckle under various vehicle load cases were then conducted based on the submodel method. The calculation results were testified to be accurate and reliable by the field measurements, which show the efficiency and reliability of the submodel method on analyzing the mechanical condition of the central buckle of long-span suspension bridges. Finally, the working behavior and mechanical characteristics of the central buckle of the RSB under vehicle loads were analyzed based on the calculation and measurement results. The results obtained in this paper can provide theoretic references for analyzing and designing the rigid central buckle in long-span suspension bridges in future.

  13. Effects of Elastic Edge Restraints and Initial Prestress on the Buckling Response of Compression-Loaded Composite Panels

    Science.gov (United States)

    Hilburger, Mark W.; Nemeth, Michael P.; Riddick, Jaret C.; Thornburgh, Robert P.

    2004-01-01

    A parametric study of the effects of test-fixture-induced initial prestress and elastic edge restraints on the prebuckling and buckling responses of a compression-loaded, quasi-isotropic curved panel is presented. The numerical results were obtained by using a geometrically nonlinear finite element analysis code with high-fidelity models. The results presented show that a wide range of prebuckling and buckling behavior can be obtained by varying parameters that represent circumferential loaded-edge restraint and rotational unloaded-edge restraint provided by a test fixture and that represent the mismatch in specimen and test-fixture radii of curvature. For a certain range of parameters, the panels exhibit substantial nonlinear prebuckling deformations that yield buckling loads nearly twice the corresponding buckling load predicted by a traditional linear bifurcation buckling analysis for shallow curved panels. In contrast, the results show another range of parameters exist for which the nonlinear prebuckling deformations either do not exist or are relatively benign, and the panels exhibit buckling loads that are nearly equal to the corresponding linear bifurcation buckling load. Overall, the results should also be of particular interest to scientists, engineers, and designers involved in simulating flight-hardware boundary conditions in structural verification and certification tests, involved in validating structural analysis tools, and interested in tailoring buckling performance.

  14. Buckling and Post-buckling Performance of Advanced Composite Stiffened Panel Under Compression

    Directory of Open Access Journals (Sweden)

    ZHANG Haoyu

    2016-08-01

    Full Text Available The axial compressive experiment was conducted on the domestic advanced composite stiffened panel, and its buckling and post-buckling performance was analyzed by monitoring strain and out-of-plane displacement of typical positions. The initial buckling load and buckling mode of panels were calculated by engineering methods to direct the follow-up axial compressive experiment. The experimental results show that the buckling patterns are mainly local buckling of panels between stiffeners, the second buckling of few positions of panels and cylindrical buckling of all 4 stiffeners successively; after local buckling of panels, part of load bearded by panels before is transferred to stiffeners and then stiffeners become the main bearing part; after fracture failure of stiffeners, the specimen is destroyed rapidly; the average value of failure load is 482.67 kN, which is 2.37 times of 204 kN of the average value of buckling load; the composite stiffened panel can bear more load after buckling.

  15. 缓慢复活型滑坡滑带土的蠕变性质与特征强度试验研究%Creep behavior of slip zone of reactivated slow-moving landslide and its characteristic strength

    Institute of Scientific and Technical Information of China (English)

    蒋秀姿; 宝萍

    2015-01-01

    锁儿头滑坡是甘肃省舟曲县城附近、体积约72.85×106 m3的一个巨型老滑坡。20世纪70年代末滑坡开始复活,至今一直处于缓慢活动之中,显示滑坡活动具有典型的蠕动特点。滑带力学特性是控制滑坡活动机制的关键因素之一,为了弄清该滑坡滑带物质的蠕变性质以及控制滑坡活动的强度指标,通过滑带土残余状态下的直剪蠕变试验,研究了滑坡滑带土的蠕变特性,比较了滑带长期强度和残余强度的关系。研究发现,滑带土蠕变特性与应力状态相关,滑带进入加速蠕变的临界剪应力和剪切速率均与正应力线性正相关。该滑坡应力状态指示其已具备进入加速蠕变的条件。残余状态下该滑坡滑带土的长期与残余强度基本等价,前者略大于后者,且增大量值与正应力有负相关关系。%The Suoertou landslide, a giant old landslide with a volume of 72.85×106 m3 in Zhouqu county, Gansu province of China, has been reactivated with a small rate since 1970’s. The slow-moving character indicates the typical rheological behavior of the landslide. It is well known that mechanical characteristic of slip zone plays an important role in landslide activities. In order to clarify the creep behavior of slip zone and the relationship between long-term strength and residual strength, a series of directed creep shear tests under residual state is employed. It is found that the creep behavior of residual slip zone is strongly dependent on normal and shear stress, with two critical shear stresses and two critical initial strain rates. Moreover, it can be found that the critical shear stress and strain rate, when the creep develops into accelerated stage, have a linear relationship with normal stress separately. Based on the linear relationship between critical shear stress and normal stress, it can be speculated that the shear stress condition of the Suoertou landslide has been in

  16. Compression Buckling Behavior of Large-Scale Friction Stir Welded and Riveted 2090-T83 Al-Li Alloy Skin-Stiffener Panels

    Science.gov (United States)

    Hoffman, Eric K.; Hafley, Robert A.; Wagner, John A.; Jegley, Dawn C.; Pecquet, Robert W.; Blum, Celia M.; Arbegast, William J.

    2002-01-01

    To evaluate the potential of friction stir welding (FSW) as a replacement for traditional rivet fastening for launch vehicle dry bay construction, a large-scale friction stir welded 2090-T83 aluminum-lithium (Al-Li) alloy skin-stiffener panel was designed and fabricated by Lockheed-Martin Space Systems Company - Michoud Operations (LMSS) as part of NASA Space Act Agreement (SAA) 446. The friction stir welded panel and a conventional riveted panel were tested to failure in compression at the NASA Langley Research Center (LaRC). The present paper describes the compression test results, stress analysis, and associated failure behavior of these panels. The test results provide useful data to support future optimization of FSW processes and structural design configurations for launch vehicle dry bay structures.

  17. Flexural buckling of fire exposed aluminium columns

    NARCIS (Netherlands)

    Maljaars, J.; Twilt, L.; Soetens, F.

    2009-01-01

    In order to study buckling of fire exposed aluminium columns, a finite element model is developed. The results of this model are verified with experiments. Based on a parametric study with the finite element model, it is concluded that the simple calculation model for flexural buckling of fire expos

  18. On the analysis of viscoplastic buckling

    DEFF Research Database (Denmark)

    Mikkelsen, Lars Pilgaard

    1993-01-01

    For elastic-viscoplastic structures the classical elastic-plastic bifurcation approach to inelastic buckling is not valid. Only an elastic bifurcation point exists in the el~tic-viscoplastic case, and the inelastic buckling behaviour is controlled by a strong sensitivity to small imperfections...

  19. Creep properties of Pb-free solder joints

    Energy Technology Data Exchange (ETDEWEB)

    Song, H.G.; Morris Jr., J.W.; Hua, F.

    2002-04-01

    Describes the creep behavior of three Sn-rich solders that have become candidates for use in Pb-free solder joints: Sn-3.5Ag, Sn-3Ag-0.5Cu and Sn-0.7Cu. The three solders show the same general behavior when tested in thin joints between Cu and Ni/Au metallized pads at temperatures between 60 and 130 C. Their steady-state creep rates are separated into two regimes with different stress exponents(n). The low-stress exponents range from {approx}3-6, while the high-stress exponents are anomalously high (7-12). Strikingly, the high-stress exponent has a strong temperature dependence near room temperature, increasing significantly as the temperature drops from 95 to 60 C. The anomalous creep behavior of the solders appears to be due to the dominant Sn constituent. Joints of pure Sn have stress exponents, n, that change with stress and temperature almost exactly like those of the Sn-rich solder joints. Research on creep in bulk samples of pure Sn suggests that the anomalous temperature dependence of the stress exponent may show a change in the dominant mechanism of creep. Whatever its source, it has the consequence that conventional constitutive relations for steady-state creep must be used with caution in treating Sn-rich solder joints, and qualification tests that are intended to verify performance should be carefully designed.

  20. Biaxial thermal creep of Inconel 617 and Haynes 230 at 850 and 950 °C

    Science.gov (United States)

    Tung, Hsiao-Ming; Mo, Kun; Stubbins, James F.

    2014-04-01

    The biaxial thermal creep behavior of Inconel 617 and Haynes 230 at 850 and 950 °C was investigated. Biaxial stresses were generated using the pressurized tube technique. The detailed creep deformation and fracture mechanism have been studied. Creep curves for both alloys showed that tertiary creep accounts for a greater portion of the materials' life, while secondary creep only accounts for a small portion. Fractographic examinations of the two alloys indicated that nucleation, growth, and coalescence of creep voids are the dominant micro-mechanisms for creep fracture. At 850 °C, alloy 230 has better creep resistance than alloy 617. When subjected to the biaxial stress state, the creep rupture life of the two alloys was considerably reduced when compared to the results obtained by uniaxial tensile creep tests. The Monkman-Grant relation proves to be a promising method for estimating the long-term creep life for alloy 617, whereas alloy 230 does not follow the relation. This might be associated with the significant changes in the microstructure of alloy 230 at high temperatures.

  1. Sequential buckling of an elastic wall

    Science.gov (United States)

    Bico, Jose; Bense, Hadrien; Keiser, Ludovic; Roman, Benoit; Melo, Francisco; Abkarian, Manouk

    A beam under quasistatic compression classically buckles beyond a critical threshold. In the case of a free beam, the lowest buckling mode is selected. We investigate the case of a long ``wall'' grounded of a compliant base and compressed in the axial compression. In the case of a wall of slender rectangular cross section, the selected buckling mode adopts a nearly fixed wavelength proportional to the height of the wall. Higher compressive loads only increase the amplitude of the buckle. However if the cross section has a sharp shape (such as an Eiffel tower profile), we observe successive buckling modes of increasing wavelength. We interpret this unusual evolution in terms of scaling arguments. At small scales, this variable periodicity might be used to develop tunable optical devices. We thank ECOS C12E07, CNRS-CONICYT, and Fondecyt Grant No. N1130922 for partially funding this work.

  2. Reassembling Surveillance Creep

    DEFF Research Database (Denmark)

    Bøge, Ask Risom; Lauritsen, Peter

    2017-01-01

    We live in societies in which surveillance technologies are constantly introduced, are transformed, and spread to new practices for new purposes. How and why does this happen? In other words, why does surveillance “creep”? This question has received little attention either in theoretical...... development or in empirical analyses. Accordingly, this article contributes to this special issue on the usefulness of Actor-Network Theory (ANT) by suggesting that ANT can advance our understanding of ‘surveillance creep’. Based on ANT’s model of translation and a historical study of the Danish DNA database......, we argue that surveillance creep involves reassembling the relations in surveillance networks between heterogeneous actors such as the watchers, the watched, laws, and technologies. Second, surveillance creeps only when these heterogeneous actors are adequately interested and aligned. However...

  3. Creep/Stress Rupture Behavior and Failure Mechanisms of Full CVI and Full PIP SiC/SiC Composites at Elevated Temperatures in Air

    Science.gov (United States)

    Bhatt, R. T.; Kiser, J. D.

    2017-01-01

    SiC/SiC composites fabricated by melt infiltration are being considered as potential candidate materials for next generation turbine components. However these materials are limited to 2400 F application because of the presence of residual silicon in the SiC matrix. Currently there is an increasing interest in developing and using silicon free SiC/SiC composites for structural aerospace applications above 2400 F. Full PIP or full CVI or CVI + PIP hybrid SiC/SiC composites can be fabricated without excess silicon, but the upper temperature stress capabilities of these materials are not fully known. In this study, the on-axis creep and rupture properties of the state-of-the-art full CVI and full PIP SiC/SiC composites with Sylramic-iBN fibers were measured at temperatures to 2700 F in air and their failure modes examined. In this presentation creep rupture properties, failure mechanisms and upper temperature capabilities of these two systems will be discussed and compared with the literature data.

  4. An Approximate Solution and Master Curves for Buckling of Symmetrically Laminated Composite Cylinders

    Science.gov (United States)

    Nemeth, Michael P.

    2013-01-01

    Nondimensional linear-bifurcation buckling equations for balanced, symmetrically laminated cylinders with negligible shell-wall anisotropies and subjected to uniform axial compression loads are presented. These equations are solved exactly for the practical case of simply supported ends. Nondimensional quantities are used to characterize the buckling behavior that consist of a stiffness-weighted length-to-radius parameter, a stiffness-weighted shell-thinness parameter, a shell-wall nonhomogeneity parameter, two orthotropy parameters, and a nondimensional buckling load. Ranges for the nondimensional parameters are established that encompass a wide range of laminated-wall constructions and numerous generic plots of nondimensional buckling load versus a stiffness-weighted length-to-radius ratio are presented for various combinations of the other parameters. These plots are expected to include many practical cases of interest to designers. Additionally, these plots show how the parameter values affect the distribution and size of the festoons forming each response curve and how they affect the attenuation of each response curve to the corresponding solution for an infinitely long cylinder. To aid in preliminary design studies, approximate formulas for the nondimensional buckling load are derived, and validated against the corresponding exact solution, that give the attenuated buckling response of an infinitely long cylinder in terms of the nondimensional parameters presented herein. A relatively small number of "master curves" are identified that give a nondimensional measure of the buckling load of an infinitely long cylinder as a function of the orthotropy and wall inhomogeneity parameters. These curves reduce greatly the complexity of the design-variable space as compared to representations that use dimensional quantities as design variables. As a result of their inherent simplicity, these master curves are anticipated to be useful in the ongoing development of

  5. A Novel Rational Design Method for Laminated Composite Structures Exhibiting Complex Geometrically Nonlinear Buckling Behaviour

    DEFF Research Database (Denmark)

    Lindgaard, Esben; Lund, Erik

    2012-01-01

    This paper presents a novel FEM-based approach for fiber angle optimal design of laminated composite structures exhibiting complicated nonlinear buckling behavior, thus enabling design of lighter and more cost-effective structures. The approach accounts for the geometrically nonlinear behavior...

  6. Observation of optomechanical buckling transitions

    Science.gov (United States)

    Xu, H.; Kemiktarak, U.; Fan, J.; Ragole, S.; Lawall, J.; Taylor, J. M.

    2017-03-01

    Correlated phases of matter provide long-term stability for systems as diverse as solids, magnets and potential exotic quantum materials. Mechanical systems, such as buckling transition spring switches, can have engineered, stable configurations whose dependence on a control variable is reminiscent of non-equilibrium phase transitions. In hybrid optomechanical systems, light and matter are strongly coupled, allowing engineering of rapid changes in the force landscape, storing and processing information, and ultimately probing and controlling behaviour at the quantum level. Here we report the observation of first- and second-order buckling transitions between stable mechanical states in an optomechanical system, in which full control of the nature of the transition is obtained by means of the laser power and detuning. The underlying multiwell confining potential we create is highly tunable, with a sub-nanometre distance between potential wells. Our results enable new applications in photonics and information technology, and may enable explorations of quantum phase transitions and macroscopic quantum tunnelling in mechanical systems.

  7. Elevated temperature tensile and creep behavior of a SiC fiber-reinforced titanium metal matrix composite. Final Report, 22 Dec. 1994 M.S. Thesis, 7 May 1993

    Science.gov (United States)

    Thurston, Rita J.

    1995-01-01

    In this research program, the tensile properties and creep behavior in air of (0)(sub 4), (0/90)(sub s) and (90)(sub 4) SCS-9/Beta 21S composite layups with 0.24 volume fraction fiber were evaluated. Monotonic tensile tests at 23, 482, 650 and 815 C yielded the temperature dependence of the elastic modulus, proportional limit, ultimate tensile strength and total strain at failure. At 650 C, the UTS of the (0)(sub 4) and (0/90)(sub s) layups decreases by almost 50 percent from the room temperature values, indicating that operating temperatures should be less than 650 C to take advantage of the specific tensile properties of these composites.

  8. Creep failure of a spray drier

    CSIR Research Space (South Africa)

    Carter, P

    1998-06-01

    Full Text Available , and creep. The calculations pointed to creep, and no positive metallurgic or physical evidence was discovered to support any of the hypotheses. However, the compression stresses implied that creep deformation could have occurred without inducing discernible...

  9. Nitinol stent design - understanding axial buckling.

    Science.gov (United States)

    McGrath, D J; O'Brien, B; Bruzzi, M; McHugh, P E

    2014-12-01

    Nitinol׳s superelastic properties permit self-expanding stents to be crimped without plastic deformation, but its nonlinear properties can contribute towards stent buckling. This study investigates the axial buckling of a prototype tracheobronchial nitinol stent design during crimping, with the objective of eliminating buckling from the design. To capture the stent buckling mechanism a computational model of a radial force test is simulated, where small geometric defects are introduced to remove symmetry and allow buckling to occur. With the buckling mechanism ascertained, a sensitivity study is carried out to examine the effect that the transitional plateau region of the nitinol loading curve has on stent stability. Results of this analysis are then used to redesign the stent and remove buckling. It is found that the transitional plateau region can have a significant effect on the stability of a stent during crimping, and by reducing the amount of transitional material within the stent hinges during loading the stability of a nitinol stent can be increased.

  10. Modified Burger’s model for describing creep behavior of tomato fruits%番茄果实蠕变特性表征的Burger’s修正模型

    Institute of Scientific and Technical Information of China (English)

    刘继展; 白欣欣; 李萍萍

    2013-01-01

    error of different ripening periods with the new model were 0.9975-0.9994 and 0.04047-0.07633, respectively, which are more ideal, obviously. The average relative errors of the rate of creep deformation, and the rate of elasticity with the new model were only 2.54%-3.04% and 2.89%-7.12%, respectively. The average relative error of the creep deformation prediction with the new model were 0.29%-0.46%, which are several times less than not only the Burger’s model but also the existing modified exponential and power-law models. Finally, the initial creep deformation rate of the new model was also closer to the real rate than any other models. To conclude, this study used a good 4-element with 6-parameter modified model to express and predict the creep behavior more accurately, which gives a better model option to bruise reducing in fruit harvesting, transporting or sorting.

  11. Low cycle fatigue and creep-fatigue interaction behavior of nickel-base superalloy GH4169 at elevated temperature of 650 °C

    Energy Technology Data Exchange (ETDEWEB)

    Chen, G., E-mail: agang@tju.edu.cn [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Zhang, Y. [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Xu, D.K. [Environmental Corrosion Center, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Lin, Y.C. [School of Mechanical and Electrical Engineering, Central South University, Changsha 410083 (China); Chen, X. [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China)

    2016-02-08

    Total strain-controlled low cycle fatigue (LCF) tests of a nickel based superalloy were performed at 650 °C. Various hold times were introduced at the peak tensile strain to investigate the high-temperature creep-fatigue interaction (CFI) effects under the same temperature. A substantial decrease in fatigue life occurred as the total strain amplitude increased. Moreover, tensile strain holding further reduced fatigue life. The saturation phenomenon of holding effect was found when the holding period reached 120 s. Cyclic softening occurred during the LCF and CFI process and it was related to the total strain amplitude and the holding period. The relationship between life-time and total strain amplitude was obtained by combining Basquin equation and Coffin-Manson equation. The surface and fracture section of the fatigued specimens were observed via scanning electronic microscope (SEM) to determine the failure mechanism.

  12. Snap-Through Buckling Problem of Spherical Shell Structure

    Directory of Open Access Journals (Sweden)

    Sumirin Sumirin

    2014-12-01

    Full Text Available This paper presents results of a numerical study on the nonlinear behavior of shells undergoing snap-through instability. This research investigates the problem of snap-through buckling of spherical shells applying nonlinear finite element analysis utilizing ANSYS Program. The shell structure was modeled by axisymmetric thin shell of finite elements. Shells undergoing snap-through buckling meet with significant geometric change of their physical configuration, i.e. enduring large deflections during their deformation process. Therefore snap-through buckling of shells basically is a nonlinear problem. Nonlinear numerical operations need to be applied in their analysis. The problem was solved by a scheme of incremental iterative procedures applying Newton-Raphson method in combination with the known line search as well as the arc- length methods. The effects of thickness and depth variation of the shell is taken care of by considering their geometrical parameter l. The results of this study reveal that spherical shell structures subjected to pressure loading experience snap-through instability for values of l≥2.15. A form of ‘turn-back’ of the load-displacement curve took place at load levels prior to the achievement of the critical point. This phenomenon was observed for values of l=5.0 to l=7.0.

  13. Buckling of a beam extruded into highly viscous fluid

    Science.gov (United States)

    Gosselin, F. P.; Neetzow, P.; Paak, M.

    2014-11-01

    Inspired by microscopic Paramecia which use trichocyst extrusion to propel themselves away from thermal aggression, we propose a macroscopic experiment to study the stability of a slender beam extruded in a highly viscous fluid. Piano wires were extruded axially at constant speed in a tank filled with corn syrup. The force necessary to extrude the wire was measured to increase linearly at first until the compressive viscous force causes the wire to buckle. A numerical model, coupling a lengthening elastica formulation with resistive-force theory, predicts a similar behavior. The model is used to study the dynamics at large time when the beam is highly deformed. It is found that at large time, a large deformation regime exists in which the force necessary to extrude the beam at constant speed becomes constant and length independent. With a proper dimensional analysis, the beam can be shown to buckle at a critical length based on the extrusion speed, the bending rigidity, and the dynamic viscosity of the fluid. Hypothesizing that the trichocysts of Paramecia must be sized to maximize their thrust per unit volume as well as avoid buckling instabilities, we predict that their bending rigidity must be about 3 ×10-9N μ m2 . The verification of this prediction is left for future work.

  14. Molecular dynamics simulations of the buckling of graphyne and its family

    Energy Technology Data Exchange (ETDEWEB)

    Salmalian, K., E-mail: kavehsalmalian@iaul.ac.ir; Rouhi, S.; Mehran, S.

    2015-01-15

    Molecular dynamics simulations are employed to study the instability characteristics of graphyne and its family under compressive loads. The effects of nanosheet side length and aspect ratio on the critical compressive force and critical strain are investigated. It is shown that increasing aspect ratio leads to decreasing the critical compressive force. Besides, the effect of atomic structure on the compressive behavior of nanosheets is explored. It is observed that the zigzag graphynes have larger buckling forces than the armchair graphynes with same geometries. Finally, the buckling behavior of different nanosheets from the graphyne family is studied. It is represented that the nanosheets with more acetylene links have smaller critical compressive forces.

  15. Failure of bacterial streamers in creeping flows

    Science.gov (United States)

    Biswas, Ishita; Ghosh, Ranajay; Sadrzadeh, Mohtada; Kumar, Aloke

    2016-11-01

    In the recent years, the dynamical response of filamentous bacterial aggregates called bacterial streamer in creeping flows has attracted attention. We report the observation of 'necking-type' instability leading to failure in bacterial (Pseudomonas fluorescens) streamers formed in creeping flows. Quantification of the failure process was made possible through the use of 200 nm red fluorescent polystyrene tracer particles embedded in the bacterial extracellular polymeric substances (EPS). The nonlinear failure behavior shows distinct phases of deformation with mutually different characteristic times, which end with a distinct localized failure of the streamer. We also develop a simplified analytical model to describe the experimental observations of the failure phenomena. The theoretical power law relationship between critical stretch ratio and the fluid velocity scale matches closely experimental observations.

  16. Creep, fatigue and creep-fatigue interactions in modified 9% Chromium - 1% Molybdenum (P91) steels

    Science.gov (United States)

    Kalyanasundaram, Valliappa

    Grade P91 steel, from the class of advanced high-chrome ferritic steels, is one of the preferred materials for many elevated temperature structural components. Creep-fatigue (C-F) interactions, along with oxidation, can accelerate the kinetics of damage accumulation and consequently reduce such components' life. Hence, reliable C-F test data is required for meticulous consideration of C-F interactions and oxidation, which in turn is vital for sound design practices. It is also imperative to develop analytical constitutive models that can simulate and predict material response under various long-term in-service conditions using experimental data from short-term laboratory experiments. Consequently, the major objectives of the proposed research are to characterize the creep, fatigue and C-F behavior of grade P91 steels at 625 C and develop robust constitutive models for simulating/predicting their microstructural response under different loading conditions. This work will utilize experimental data from 16 laboratories worldwide that conducted tests (creep, fatigue and C-F) on grade P91 steel at 625°C in a round-robin (RR) program. Along with 7 creep deformation and rupture tests, 32 pure fatigue and 46 C-F tests from the RR are considered in this work. A phenomenological constitutive model formulated in this work needs just five fitting parameters to simulate/predict the monotonic, pure fatigue and C-F behavior of grade P91 at 625 C. A modified version of an existing constitutive model is also presented for particularly simulating its isothermal creep deformation and rupture behavior. Experimental results indicate that specimen C-F lives, as measured by the 2% load drop criterion, seem to decrease with increasing strain ranges and increasing hold times at 625°C. Metallographic assessment of the tested specimens shows that the damage mode in both pure fatigue and 600 seconds hold time cyclic tests is predominantly transgranular fatigue with some presence of

  17. Buckling instability of squeezed droplets

    CERN Document Server

    Elfring, Gwynn J

    2015-01-01

    Motivated by recent experiments, we consider theoretically the compression of droplets pinned at the bottom on a surface of finite area. We show that if the droplet is sufficiently compressed at the top by a surface, it will always develop a shape instability at a critical compression. When the top surface is flat, the shape instability occurs precisely when the apparent contact angle of the droplet at the pinned surface is pi, regardless of the contact angle of the upper surface, reminiscent of past work on liquid bridges and sessile droplets as first observed by Plateau. After the critical compression, the droplet transitions from a symmetric to an asymmetric shape. The force required to deform the droplet peaks at the critical point then progressively decreases indicative of catastrophic buckling. We characterize the transition in droplet shape using illustrative examples in two dimensions followed by perturbative analysis as well as numerical simulation in three dimensions. When the upper surface is not f...

  18. Preconsolidation Pressure and Creep Settlements

    DEFF Research Database (Denmark)

    Thorsen, Grete

    1995-01-01

    of oedometer tests with undisturbed samples have been analysed by means of different methods to determine the pre-consolidation pressure. An attempt is made to estimate the creep rates on the basis of AMS 14C-datings of the sediments and a model for creep determination proposed by Moust Jacobsen....

  19. Mathematical modeling and full-scale shaking table tests for multi-curve buckling restrained braces

    Institute of Scientific and Technical Information of China (English)

    C. S. Tsai; Yungchang Lin; Wenshin Chen; H. C. Su

    2009-01-01

    Buckling restrained braces (BRBs) have been widely applied in seismic mitigation since they were introduced in the 1970s. However, traditional BRBs have several disadvantages caused by using a steel tube to envelope the mortar to prevent the core plate from buckling, such as: complex interfaces between the materials used, uncertain precision, and time consumption during the manufacturing processes. In this study, a new device called the multi-curve buckling restrained brace (MC-BRB) is proposed to overcome these disadvantages. The new device consists of a core plate with multiple neck portions assembled to form multiple energy dissipation segments, and the enlarged segment, lateral support elements and constraining elements to prevent the BRB from buckling. The enlarged segment located in the middle of the core plate can be welded to the lateral support and constraining elements to increase buckling resistance and to prevent them from sliding during earthquakes. Component tests and a series of shaking table tests on a full-scale steel structure equipped with MC-BRBs were carried out to investigate the behavior and capability of this new BRB design for seismic mitigation. The experimental results illustrate that the MC-BRB possesses a stable mechanical behavior under cyclic loadings and provides good protection to structures during earthquakes. Also, a mathematical model has been developed to simulate the mechanical characteristics of BRBs.

  20. How vein sealing boosts fracture widening rates - The buckling-enhanced aperture growth mechanism for syn-tectonic veins

    Science.gov (United States)

    Nüchter, Jens-Alexander

    2017-01-01

    The paper introduces the mechanism of buckling-enhanced aperture growth for syn-tectonic veins that formed in simple-shear dominated kinematic frameworks in the middle or lower crust. Apart from the well understood concepts of fracture widening driven by effective tensile stresses, buckling-enhanced fracture aperture growth relates widening to active outward buckling of more viscous incipient cement layers precipitated as hydrothermal minerals for the pore fluid on the walls of juvenile syn-tectonic veins, driven by fracture-parallel compressive creep strain in the host rocks. Thus, the mechanism proposed here follows similar principles as tectonic folding, although important differences exist. Inspired by the structural record of low-aspect ratio veins exposed in HP/LT metamorphic rocks cropping out on south Evia island, Greece, generic numerical models are calculated to study development of buckling instabilities in such incompletely cemented veins and their impact on aperture growth rates. The models indicate (1) that aperture growth rates increase with increasing viscosity contrast between the host rocks and the cement layers, (2) an increase in the thickness of the cement layers cause acceleration of aperture growth, (3) that support of restraining forces at the vein tips offered by the host rocks against buckling of the cement layers cause fully compressive states of stress ahead the fracture tips, and (4) that fracture aperture growth is possible against fully compressive fracture-normal stresses. The buckling-enhanced vein aperture growth mechanism yields important implications for the maintenance and decay of fracture-bound permeability and for the mechanical state of the middle and lower crust in seismically active regions.

  1. Linear extrapolation for prediction of tensile creep compliance of polyvinyl chloride

    Institute of Scientific and Technical Information of China (English)

    XIE Gang

    2005-01-01

    The universal creep equation is successful in relating the creep (ε) to the aging time (te), coefficient of retardation time (β), and intrinsic time (to ). This relation was used to treat the creep experimental data for polyvinyl chloride (PVC) specimens at a given stress and different aging times. The βgs found by the "polynomial fitting" method in this work instead of the "middle -point" method reported in the literature. The unified master line was constructed with the treated data and curves according to the universal equation. The master line can be used to predict the long -term creep behavior and lifetime by extrapolating.

  2. Review of data on irradiation creep of monolithic SiC

    Energy Technology Data Exchange (ETDEWEB)

    Garner, F.A.; Youngblood, G.E.; Hamilton, M.L. [Pacific Northwest National Laboratory, Richland, WA (United States)

    1996-04-01

    An effort is now underway to design an irradiation creep experiment involving SiC composites to SiC fibers. In order to successfully design such an experiment, it is necessary to review and assess the available data for monolithic SiC to establish the possible bounds of creep behavior for the composite. The data available show that monolithic SiC will indeed creep at a higher rate under irradiation compared to that of thermal creep, and surprisingly, it will do so in a temperature-dependant manner that is typical of metals.

  3. On the prediction of stress relaxation from known creep of nonlinear materials

    Energy Technology Data Exchange (ETDEWEB)

    Touati, D.; Cederbaum, G. [Ben-Gurion Univ. of the Negev, Beer Sheva (Israel)

    1997-04-01

    A method to predict the nonlinear relaxation behavior from creep experiments of nonlinear viscoelastic materials is presented. It is shown that for given nonlinear creep properties, and creep compliance represented by the Prony series, the Schapery creep model can be transformed into a set of first order nonlinear equations. The solution of these equations enables the obtaining of the nonlinear stress relaxation curves. The strain-dependent constitutive equation can then be constructed for a given nonlinear viscoelastic model, as needed for engineering applications. A comparison example of the calculated stress relaxation curves, with test data for polyurethane demonstrates the very good accuracy of the proposed method.

  4. Investigation of creep by use of closed loop servo-hydraulic test system

    Science.gov (United States)

    Wu, H. C.; Yao, J. C.

    1981-01-01

    Creep tests were conducted by means of a closed loop servo-controlled materials test system. These tests are different from the conventional creep tests in that the strain history prior to creep may be carefully monitored. Tests were performed for aluminum alloy 6061-0 at 150 C and monitored by a PDP 11/04 minicomputer at a preset constant plastic-strain rate prehistory. The results show that the plastic-strain rate prior to creep plays a significant role in creep behavior. The endochronic theory of viscoplasticity was applied to describe the observed creep curves. The concepts of intrinsic time and strain rate sensitivity function are employed and modified according to the present observation.

  5. Creep investigation of GFRP RC Beams - Part B: a theoretical framework

    Directory of Open Access Journals (Sweden)

    masmoudi abdelmonem

    2014-11-01

    Full Text Available This paper presents an analytical study about the viscoelastic time-dependent (creep behavior of pultruded GFRP elements made of polyester and E-glass fibres. Experimental results reported in Part A are firstly used for material characterization by means of empirical and phenomenological formulations.   The superposition principles by adopting the law of creep following the Eurocode 2 recommendations are also investigated. Analytical study was also conducted including creep under constant stress; successions of increasing stress superposition principle equivalent time and the return creep reloading. The results of this study revealed that Beams reinforced with GFRP are less marked with creep phenomenon.  This investigation should guide the civil engineer/designer for a better understanding creep phenomenon in GFRP reinforced concrete members.

  6. Scleral buckle infection with Alcaligenes xylosoxidans

    Directory of Open Access Journals (Sweden)

    Chih-Kang Hsu

    2014-01-01

    Full Text Available We describe a rare case of extraocular inflammation secondary to scleral buckle infection with Alcaligenes xylosoxidans. A 60-year-old female with a history of retinal detachment repair with open-book technique of scleral buckling presented with purulent discharge and irritation in the right eye that had begun 4 weeks earlier and had been treated ineffectively at another hospital. Conjunctival erosion with exposure of the scleral buckle was noted. The scleral buckle was removed and cultured. The explanted material grew gram-negative rod later identified as A. xylosoxidans. On the basis of the susceptibility test results, the patient was treated by subconjunctival injection and fortified topical ceftazidime. After 4 weeks of treatment, the infection resolved.

  7. Scleral buckle infection with Alcaligenes xylosoxidans.

    Science.gov (United States)

    Hsu, Chih-Kang; Chang, Yun-Hsiang; Chen, Jiann-Torng

    2014-06-01

    We describe a rare case of extraocular inflammation secondary to scleral buckle infection with Alcaligenes xylosoxidans. A 60-year-old female with a history of retinal detachment repair with open-book technique of scleral buckling presented with purulent discharge and irritation in the right eye that had begun 4 weeks earlier and had been treated ineffectively at another hospital. Conjunctival erosion with exposure of the scleral buckle was noted. The scleral buckle was removed and cultured. The explanted material grew gram-negative rod later identified as A. xylosoxidans. On the basis of the susceptibility test results, the patient was treated by subconjunctival injection and fortified topical ceftazidime. After 4 weeks of treatment, the infection resolved.

  8. Buckling optimisation of sandwich cylindrical panels

    Science.gov (United States)

    Abouhamzeh, M.; Sadighi, M.

    2016-06-01

    In this paper, the buckling load optimisation is performed on sandwich cylindrical panels. A finite element program is developed in MATLAB to solve the governing differential equations of the global buckling of the structure. In order to find the optimal solution, the genetic algorithm Toolbox in MATLAB is implemented. Verifications are made for both the buckling finite element code and also the results from the genetic algorithm by comparisons to the results available in literature. Sandwich cylindrical panels are optimised for the buckling strength with isotropic or orthotropic cores with different boundary conditions. Results are presented in terms of stacking sequence of fibers in the face sheets and core to face sheet thickness ratio.

  9. Long-term creep-rupture failure envelope of epoxy

    Science.gov (United States)

    Melo, José Daniel D.; de Medeiros, Antonio M.

    2014-02-01

    An accelerated testing methodology based on the time-temperature superposition principle has been proposed in the literature for the long-term creep strength of polymer matrices and polymer composites. Also, it has been suggested that a standard master curve may be a feasible assumption to describe the creep behavior in both tension and compression modes. In the present research, strength master curves for an aerospace epoxy (8552) were generated for tension and compression, by shifting strength data measured at various temperatures. The shift function is obtained from superposition of creep-compliance curves obtained at different temperatures. A standard master curve was presented to describe the creep-rupture of the polymer under tension and compression. Moreover, long-term creep-rupture failure envelopes of the polymer were presented based on a two-part failure criterion for homogeneous and isotropic materials. Ultimately, the approach presented allows the prediction of creep-rupture failure envelopes for a time-dependent material based on tensile strengths measured at various temperatures, considering that the ratio between tensile and compressive strengths is known.

  10. Cumulative creep fatigue damage in 316 stainless steel

    Science.gov (United States)

    Mcgaw, Michael A.

    1989-01-01

    The cumulative creep-fatigue damage behavior of 316 stainless steel at 1500 F was experimentally established for the two-level loading cases of fatigue followed by fatigue, creep fatigue followed by fatigue, and fatigue followed by creep fatigue. The two-level loadings were conducted such that the lower life (high strain) cycling was applied first for a controlled number of cycles and the higher life (low strain) cycling was conducted as the second level to failure. The target life levels in this study were 100 cycles to failure for both the fatigue and creep-fatigue lowlife loading, 5000 cycles to failure for the higher life fatigue loading and 10,000 cycles to failure for the higher life creep-fatigue loading. The failed specimens are being examined both fractographically and metallographically to ascertain the nature of the damaging mechanisms that produced failure. Models of creep-fatigue damage accumulation are being evaluated and knowledge of the various damaging mechanisms is necessary to ensure that predictive capability is instilled in the final failure model.

  11. Rationalization of Creep Data of Creep-Resistant Steels on the Basis of the New Power Law Creep Equation

    Science.gov (United States)

    Wang, Q.; Yang, M.; Song, X. L.; Jia, J.; Xiang, Z. D.

    2016-07-01

    The conventional power law creep equation (Norton equation) relating the minimum creep rate to creep stress and temperature cannot be used to predict the long-term creep strengths of creep-resistant steels if its parameters are determined only from short-term measurements. This is because the stress exponent and activation energy of creep determined on the basis of this equation depend on creep temperature and stress and these dependences cannot be predicted using this equation. In this work, it is shown that these problems associated with the conventional power law creep equation can be resolved if the new power law equation is used to rationalize the creep data. The new power law creep equation takes a form similar to the conventional power law creep equation but has a radically different capability not only in rationalizing creep data but also in predicting the long-term creep strengths from short-term test data. These capabilities of the new power law creep equation are demonstrated using the tensile strength and creep test data measured for both pipe and tube grades of the creep-resistant steel 9Cr-1.8W-0.5Mo-V-Nb-B (P92 and T92).

  12. A review of the high temperature creep in oxide nuclear fuels (I)

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Young Woo; Na, S. H.; Lee, Y. W.; Kim, H. S.; Kim, S. H.; Joung, C. Y

    1998-06-01

    Since the initial stage of fuel developmental until recently, considerable efforts have been extensively directed at studying the creep properties of uranium dioxide and its related phases largely due to the importance of their application to the reactor fuels. In this state-of-the-art report, the creep behavior and mechanisms of UO{sub 2} and its related phases were reviewed and discussed in terms of experimental variables such as applied stress, temperature, microstructure and stoichiometry. The objective of this review is to obtain a complete understanding of the influences of these variables on the creep property and creep mechanism in these materials aiming at devising more proper methods for the improvement of the behavior. The database obtained from the results will be primarily utilized also, as the reference data for studying the creep behavior of UO{sub 2}-based mixed oxide nuclear fuels. (author). 64 refs., 6 tabs., 25 figs

  13. Investigation of the effect of aggregates' morphology on concrete creep properties by numerical simulations

    Energy Technology Data Exchange (ETDEWEB)

    Lavergne, F. [Université Paris-Est, Laboratoire Navier (ENPC, IFSTTAR, CNRS), 77455 Marne-la-Vallée Cedex (France); Sab, K., E-mail: karam.sab@enpc.fr [Université Paris-Est, Laboratoire Navier (ENPC, IFSTTAR, CNRS), 77455 Marne-la-Vallée Cedex (France); Sanahuja, J. [Département Mécanique des Matériaux et des Composants, EDF R& D, Site des Renardières, Avenue des Renardières, 77818 Moret-Sur-Loing Cedex (France); Bornert, M. [Université Paris-Est, Laboratoire Navier (ENPC, IFSTTAR, CNRS), 77455 Marne-la-Vallée Cedex (France); Toulemonde, C. [Département Mécanique des Matériaux et des Composants, EDF R& D, Site des Renardières, Avenue des Renardières, 77818 Moret-Sur-Loing Cedex (France)

    2015-05-15

    Prestress losses due to creep of concrete is a matter of interest for long-term operations of nuclear power plants containment buildings. Experimental studies by Granger (1995) have shown that concretes with similar formulations have different creep behaviors. The aim of this paper is to numerically investigate the effect of size distribution and shape of elastic inclusions on the long-term creep of concrete. Several microstructures with prescribed size distribution and spherical or polyhedral shape of inclusions are generated. By using the 3D numerical homogenization procedure for viscoelastic microstructures proposed by Šmilauer and Bažant (2010), it is shown that the size distribution and shape of inclusions have no measurable influence on the overall creep behavior. Moreover, a mean-field estimate provides close predictions. An Interfacial Transition Zone was introduced according to the model of Nadeau (2003). It is shown that this feature of concrete's microstructure can explain differences between creep behaviors.

  14. Variations in creep rate along the Hayward Fault, California, interpreted as changes in depth of creep

    Science.gov (United States)

    Simpson, R.W.; Lienkaemper, J.J.; Galehouse, J.S.

    2001-01-01

    Variations ill surface creep rate along the Hayward fault are modeled as changes in locking depth using 3D boundary elements. Model creep is driven by screw dislocations at 12 km depth under the Hayward and other regional faults. Inferred depth to locking varies along strike from 4-12 km. (12 km implies no locking.) Our models require locked patches under the central Hayward fault, consistent with a M6.8 earthquake in 1868, but the geometry and extent of locking under the north and south ends depend critically on assumptions regarding continuity and creep behavior of the fault at its ends. For the northern onshore part of the fault, our models contain 1.4-1.7 times more stored moment than the model of Bu??rgmann et al. [2000]; 45-57% of this stored moment resides in creeping areas. It is important for seismic hazard estimation to know how much of this moment is released coseismically or as aseismic afterslip.

  15. Scleral buckle infection with aspergillus flavus

    Directory of Open Access Journals (Sweden)

    Bouhaimed Manal

    2008-01-01

    Full Text Available Purpose: To present a case of scleral buckle infection with Aspergillus flavus in a tertiary eye center in Saudi Arabia. Methods: A retrospective case report of a 28-year-old Saudi male who presented with a six-month history of conjunctival injection and discharge from the left eye which had undergone uncomplicated conventional retinal detachment surgery, at the King Khaled Eye Specialist Hospital in Riyadh, Saudi Arabia, in the form of cryopexy, subretinal fluid drainage and scleral buckle (grooved segmental sponge and circumferential band with sleeve for a macula on retinal detachment four years earlier. A diagnosis of infected extruded scleral buckle was made and the buckle was removed. Results: The infected scleral buckle was removed under local anesthesia with administration of sub-conjunctival irrigation of 50 mg solution of Vancomycin, and sub-conjunctival injection of 25mg of Vancomycin. Post operative microbiological studies revealed infection with silver staining of moderate Aspergillus flavus hyphae. Visual acuity of the left eye improved from 20/200 before surgery to 20/60 in the two years follow-up visit. Conclusion: This case report indicates the importance of considering infection with multiple organisms - including fungal ones - in cases of scleral buckle infections in our population.

  16. Buckling transition in long α-helices

    Energy Technology Data Exchange (ETDEWEB)

    Palenčár, Peter; Bleha, Tomáš, E-mail: bleha@savba.sk [Polymer Institute, Slovak Academy of Sciences, 845 41 Bratislava (Slovakia)

    2014-11-07

    The treatment of bending and buckling of stiff biopolymer filaments by the popular worm-like chain model does not provide adequate understanding of these processes at the microscopic level. Thus, we have used the atomistic molecular-dynamic simulations and the Amber03 force field to examine the compression buckling of α-helix (AH) filaments at room temperature. It was found that the buckling instability occurs in AHs at the critical force f{sub c} in the range of tens of pN depending on the AH length. The decrease of the force f{sub c} with the contour length follows the prediction of the classic thin rod theory. At the force f{sub c} the helical filament undergoes the swift and irreversible transition from the smoothly bent structure to the buckled one. A sharp kink in the AH contour arises at the transition, accompanied by the disruption of the hydrogen bonds in its vicinity. The kink defect brings in an effective softening of the AH molecule at buckling. Nonbonded interactions between helical branches drive the rearrangement of a kinked AH into the ultimate buckled structure of a compact helical hairpin described earlier in the literature.

  17. 腐蚀钢绞线与混凝土的长期粘结蠕变性能试验研究%EXPERIMENTAL STUDY ON BEHAVIOR OF LONG-TERM BOND-CREEP BETWEEN CORRODED STEEL STRANDS AND CONCRETE

    Institute of Scientific and Technical Information of China (English)

    李富民; 袁迎曙

    2012-01-01

    To study the influence of steel strands corrosion on the long-term behavior of bond-creep, 6 pre-tensioned prestressed concrete beams were fabricated, of which, 5 beams were mixed with salt and set in different places to be corroded in different intensity for 47 weeks, and the bond-slip of all the 6 beams was tested periodically through the whole period, and then the time varying curves of bond-slip under prestressing were obtained. The results show that under the condition of no corrosion crack, the bond strength increases with corrosion and the bond-creep is restrained, which contribute the creep slip of corrosion beams being less than that of the uncorrosion beam. Moreover, with the increase of corrosion rate and corrosion products expansion ratio, the long-term bond-slip decreases. The analysis shows that if there are corrosion cracks and the bond strength deteriorates, the long-term bond-creep and the load cracks width in anchoring segments should increase, but the prestressing loss and the anchoring bearing capacity should not decrease.%为探讨腐蚀对钢绞线与混凝土长期粘结蠕变性能的影响,制作6根先张法预应力混凝土梁试件,其中5根试件通过掺盐并置于不同环境中进行为期47周不同强度的长期腐蚀,期间对所有6根试件进行定期粘结滑移监测,得到各试件在预应力作用下的粘结滑移时变曲线。结果表明:在未发生锈胀开裂的条件下,腐蚀引起粘结强度增大,从而抑制了粘结蠕变,使腐蚀试件的蠕变滑移小于无腐蚀试件;而且,腐蚀率越高、腐蚀产物体积膨胀率越大,长期粘结滑移也越小。分析表明:如果腐蚀引起锈胀开裂并导致粘结强度退化,则会引起长期粘结蠕变及锚固段裂缝宽度的增大,但不会引起预应力损失及锚固承载力的降低。

  18. MODELING OF NONLINEAR DEFORMATION AND BUCKLING OF ELASTIC INHOMOGENEOUS SHELLS

    Directory of Open Access Journals (Sweden)

    Bazhenov V.A.

    2014-06-01

    Full Text Available The paper outlines the fundamentals of the method of solving static problems of geometrically nonlinear deformation, buckling, and postbuckling behavior of thin thermoelastic inhomogeneous shells with complex-shaped mid-surface, geometrical features throughout the thickness, and multilayer structure under complex thermomechanical loading. The method is based on the geometrically nonlinear equations of three-dimensional thermoelasticity and the moment finiteelement scheme. The method is justified numerically. Comparing solutions with those obtained by other authors and by software LIRA and SCAD is conducted.

  19. Buckling and Multiple Equilibrium States of Viscoelastic Rectangular Plates

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    On the basis of Karman's theory of thin plates with large deflection, the Boltzmann law on linear viscoelastic materials and the mathematical model of dynamic analysis on viscoelastic thin plates, a set of nonlinear integro-partial-differential equations is first presented by means of a structural function introduced in this paper. Then,by using the Galerkin technique in spatial field and a backward difference scheme in temporal field, the set of nonlinear integro-partial-differential equations reduces to a system of nonlinear algebraic equations. After solving the algebraic equations, the buckling behavior and multiple equilibrium states can be obtained.

  20. Small punch creep test in a 316 austenitic stainless steel

    Directory of Open Access Journals (Sweden)

    Saucedo-Muñoz, Maribel L.

    2015-03-01

    Full Text Available The small punch creep test was applied to evaluate the creep behavior of a 316 type austenitic stainless steel at temperatures of 650, 675 and 700 °C. The small punch test was carried out using a creep tester with a specimen size of 10×10×0.3 mm at 650, 675 and 700 °C using loads from 199 to 512 N. The small punch creep curves show the three stages found in the creep curves of the conventional uniaxial test. The conventional creep relationships which involve parameters such as creep rate, stress, time to rupture and temperature were followed with the corresponding parameters of small punch creep test and they permitted to explain the creep behavior in this steel. The mechanism and activation energy of the deformation process were the grain boundary sliding and diffusion, respectively, during creep which caused the intergranular fracture in the tested specimens.El ensayo de termofluencia por indentación se utilizó para evaluar el comportamiento a la termofluencia en un acero inoxidable austenítico 316. Este ensayo se realizó en una máquina de indentación con muestras de 10×10×0,3 mm a temperaturas de 650, 675 y 700 °C con cargas de 199 a 512 N. Las curvas de termofluencia del ensayo mostraron las tres etapas características observadas en el ensayo convencional de tensión. Asimismo, las principales relaciones de termofluencia entre parámetros como velocidad de termofluencia, esfuerzo, tiempo de ruptura y temperatura se observaron en los parámetros correspondientes al ensayo de indentación, lo que permitió caracterizar el comportamiento de termofluencia en este acero. El mecanismo y la energía de activación del proceso de deformación en la termofluencia corresponden al deslizamiento de los límites de grano y la difusión a través de los mismos, respectivamente, lo cual causó la fractura intergranular en las muestras ensayadas.

  1. Creep Burst Testing of a Woven Inflatable Module

    Science.gov (United States)

    Selig, Molly M.; Valle, Gerard D.; James, George H.; Oliveras, Ovidio M.; Jones, Thomas C.; Doggett, William R.

    2015-01-01

    A woven Vectran inflatable module 88 inches in diameter and 10 feet long was tested at the NASA Johnson Space Center until failure from creep. The module was pressurized pneumatically to an internal pressure of 145 psig, and was held at pressure until burst. The external environment remained at standard atmospheric temperature and pressure. The module burst occurred after 49 minutes at the target pressure. The test article pressure and temperature were monitored, and video footage of the burst was captured at 60 FPS. Photogrammetry was used to obtain strain measurements of some of the webbing. Accelerometers on the test article measured the dynamic response. This paper discusses the test article, test setup, predictions, observations, photogrammetry technique and strain results, structural dynamics methods and quick-look results, and a comparison of the module level creep behavior to the strap level creep behavior.

  2. BUCKLING BEHAVIOUR OF SINGLE-WALLED CARBON NANOTUBES UNDER AXIAL LOADING

    Directory of Open Access Journals (Sweden)

    Grzegorz Litak

    2017-03-01

    Full Text Available We investigate a single walled Carbon Nanotube under an axially directed compressive line loading applied at both of its edges. The expected buckling behavior we study by application of a molecular computation approach. We formulate a global potential and search for its minimum to obtain the equilibrium configuration. Using besides the main parameter, which is the value of the loading, as second parameter the diameter of the tube, we are able to define the critical value of the diameter, for which we obtain the coincident case of local shell buckling.

  3. Creep in electronic ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Routbort, J. L.; Goretta, K. C.; Arellano-Lopez, A. R.

    2000-04-27

    High-temperature creep measurements combined with microstructural investigations can be used to elucidate deformation mechanisms that can be related to the diffusion kinetics and defect chemistry of the minority species. This paper will review the theoretical basis for this correlation and illustrate it with examples from some important electronic ceramics having a perovskite structure. Recent results on BaTiO{sub 3}, (La{sub 1{minus}x}Sr){sub 1{minus}y}MnO{sub 3+{delta}}, YBa{sub 2}Cu{sub 3}O{sub x}, Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub x}, (Bi,Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub x} and Sr(Fe,Co){sub 1.5}O{sub x} will be presented.

  4. Study of Inverse Creep In Textile Yarns

    Directory of Open Access Journals (Sweden)

    P.G. Patil

    2009-12-01

    Full Text Available Creep has been known and studied for textilematerials for decades. In comparison, a newlyobserved phenomenon of inverse creep seems not tohave received much attention. A new instrument hasbeen fabricated to measure creep and inverse creep intextile materials particularly yarns. Creep and Inversecreep measurements of nylon multifilament yarn,polyester multifilament yarn, cotton and wool yarn atdifferent levels of stress have been studied using thenew instrument and results are reported in the presentpaper.

  5. Creep modelling of particle strengthened steels

    OpenAIRE

    Magnusson, Hans

    2010-01-01

    Materials used in thermal power plants have to resist creep deformation for time periods up to 30 years. Material evaluation is typically based on creep testing with a maximum duration of a few years. This information is used as input when empirically deriving models for creep. These kinds of models are of limited use when considering service conditions or compositions different from those in the experiments. In order to provide a more general model for creep, the mechanisms that give creep s...

  6. Designing pinhole vacancies in graphene towards functionalization: Effects on critical buckling load

    Science.gov (United States)

    Georgantzinos, S. K.; Markolefas, S.; Giannopoulos, G. I.; Katsareas, D. E.; Anifantis, N. K.

    2017-03-01

    The effect of size and placement of pinhole-type atom vacancies on Euler's critical load on free-standing, monolayer graphene, is investigated. The graphene is modeled by a structural spring-based finite element approach, in which every interatomic interaction is approached as a linear spring. The geometry of graphene and the pinhole size lead to the assembly of the stiffness matrix of the nanostructure. Definition of the boundary conditions of the problem leads to the solution of the eigenvalue problem and consequently to the critical buckling load. Comparison to results found in the literature illustrates the validity and accuracy of the proposed method. Parametric analysis regarding the placement and size of the pinhole-type vacancy, as well as the graphene geometry, depicts the effects on critical buckling load. Non-linear regression analysis leads to empirical-analytical equations for predicting the buckling behavior of graphene, with engineered pinhole-type atom vacancies.

  7. A Numerical Procedure to Obtain the Creep Parameters of the Thermal Barrier Coating

    Directory of Open Access Journals (Sweden)

    Shifeng Wen

    2014-05-01

    Full Text Available Three-point bending creep test was used to understand the creep behavior of typical thin film/substrate systems—thermal barrier coating (TBC systems. Firstly, a simplified model, which does not consider the local effect, has been set up to get an analytical relationship. The important result is that creep stress exponent of materials is equal to the creep load exponent of the steady-state deflection rate of BC specimens. Secondly, in order to consider the local effect of bending, the finite element method (FEM has been carried out. FEM calculation shows that there is a steady stage of the creep deflection under a constant applied load. And the exponent of the steady-state creep deflection rate to the applied load is found to be equal to the creep stress exponent of materials. The creep constant of the materials can be obtained by a set of trials with assumed creep constants of materials and can be finally determined by the best fit method. Finally, the finite element results show that the influences of the friction, the thickness of TBCs, and the modulus ratio of TBC to the substrate on stress distribution are important.

  8. Microstructure and Creep Property of a GH4169 Nickel-based Superalloy

    Directory of Open Access Journals (Sweden)

    LIU Chen

    2017-06-01

    Full Text Available By means of direct aging (DA heat treatment, creep properties measurement and microstructure observation, the microstructure and creep behaviors of the GH4169 superalloy were investigated. Results show that the microstructure of the alloy consists of γ, γ', γ" and δ phases, and the coherent interfaces exist between the phases. The creep life of the alloy at 660℃/700 MPa is predicted to be 123h, and 39h at 680℃/700MPa. Under the testing temperature and stress range, the creep activation energy of the alloy is calculated to be 588.0 kJ/mol. The deformation mechanisms of the alloy during creep are dislocation slipping and twin deformation. The granular carbides precipitated along the grain boundaries may restrain the slipping of the boundary, which is thought to be the main reason of the good creep resistance. As the creep goes on, the slipping dislocations activated within the grains are hindered and blocked by the boundaries to cause the stress concentration, which may promote the initiation and propagation of the crack occurring along the boundaries perpendicular to the stress axis, when the value of stress concentration is higher than the bonding strength of the boundaries, up to the occurrence of creep fracture. This is thought to be the fracture mechanism of alloy during creep.

  9. Application of Finite Element Method of Numerical Modelling to Understand Toe Buckling Deformation in the Southern Alps of New Zealand.

    Science.gov (United States)

    Ridl, Romy; Bell, David; Villeneuve, Marlene

    2017-04-01

    Toe buckling deformation is a temporal product of induced stresses concentrated at the base of a slope. Prolonged induced stresses may lead to yielding of an anisotropic rock mass, either through rheological creep deformation (flexural toe buckling) or brittle failure (hinge buckling). Progressive deformation can lead to the breakout at the buckled toe and ultimately result in deep seated displacements on a mountain range scale, referred to as deep seated gravitational slope deformation (DSGSD). DSGSD can have a considerable impact on civil infrastructure and should be well understood for hazard identification, to inform civil engineering design and for resource management purposes. Toe buckling deformation was identified beneath the basal sliding zone of three large (≥50 Mm3) landslides in the Cromwell Gorge, New Zealand. This area was subjected to extensive geotechnical investigations for the Clyde Hydropower Scheme. During these investigations seventeen major landslides were identified in the Cromwell Gorge and subsequently stabilised. The data from the landslide stabilisation project, including 26.7 km of boreholes and 9 km of tunnels, for the three landslides exhibiting toe buckling was made available for this study. This comprehensive database has enabled comparison and validation of numerical simulations carried out for the Cromwell Gorge. The application of numerical modelling has demonstrated that toe buckling within the Cromwell Gorge is a result of the combination of induced stresses acting on an anisotropic schistose rock mass. The induced stresses comprise: i) topographically-induced gravitational stresses parallel to the slope, associated with the evolution of the Cromwell Gorge from a relatively low relief surface to present day topography (1400 m deep valley), and ii) active far-field tectonic stresses associated with the obliquely convergent stress regime of the Australian-Pacific continent plate boundary. Finite Element Method (FEM) numerical

  10. Plasticity and creep of metals

    CERN Document Server

    Rusinko, Andrew

    2011-01-01

    Here is a systematic presentation of the postulates, theorems and principles of mathematical theories of plasticity and creep in metals, and their applications. Special attention is paid to analysis of the advantages and shortcomings of the classical theories.

  11. null Seismic Creep, null Images

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Seismic creep is the constant or periodic movement on a fault as contrasted with the sudden rupture associated with an earthquake. It is a usually slow deformation...

  12. Creep model of unsaturated sliding zone soils and long-term deformation analysis of landslides

    Science.gov (United States)

    Zou, Liangchao; Wang, Shimei; Zhang, Yeming

    2015-04-01

    Sliding zone soil is a special soil layer formed in the development of a landslide. Its creep behavior plays a significant role in long-term deformation of landslides. Due to rainfall infiltration and reservoir water level fluctuation, the soils in the slide zone are often in unsaturated state. Therefore, the investigation of creep behaviors of the unsaturated sliding zone soils is of great importance for understanding the mechanism of the long-term deformation of a landslide in reservoir areas. In this study, the full-process creep curves of the unsaturated soils in the sliding zone in different net confining pressure, matric suctions and stress levels were obtained from a large number of laboratory triaxial creep tests. A nonlinear creep model for unsaturated soils and its three-dimensional form was then deduced based on the component model theory and unsaturated soil mechanics. This creep model was validated with laboratory creep data. The results show that this creep model can effectively and accurately describe the nonlinear creep behaviors of the unsaturated sliding zone soils. In order to apply this creep model to predict the long-term deformation process of landslides, a numerical model for simulating the coupled seepage and creep deformation of unsaturated sliding zone soils was developed based on this creep model through the finite element method (FEM). By using this numerical model, we simulated the deformation process of the Shuping landslide located in the Three Gorges reservoir area, under the cycling reservoir water level fluctuation during one year. The simulation results of creep displacement were then compared with the field deformation monitoring data, showing a good agreement in trend. The results show that the creeping deformations of landslides have strong connections with the changes of reservoir water level. The creep model of unsaturated sliding zone soils and the findings obtained by numerical simulations in this study are conducive to

  13. Creep of sound paths in consolidated granular material detected through coda wave interferometry.

    Science.gov (United States)

    Espíndola, David; Galaz, Belfor; Melo, Francisco

    2016-07-01

    The time evolution of the contact force structure of a consolidated granular material subjected to a constant stress is monitored using the coda wave interferometry method. In addition, the nature of the aging and rejuvenation processes are investigated. These processes are interpreted in terms of affine and nonaffine structural path deformations. During the later stages of creep, the rearrangements of subgrains are so small that they only produce affine deformations in the contact paths, without any significant changes in the structural configuration. As a result, the strain path distribution follows the macroscopic strain. Conversely, in the presence of ultrasonic perturbations, the nonaffine grain buckling mechanism dominates, producing relatively drastic changes in the structural configuration accompanied by path deformations of the order of the grain size. This plastic mechanism induces material rejuvenation that is observed macroscopically as an ultrasonically accelerated creep.

  14. Buckling Analysis of Supporting Skirt of Security Injection Tank

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    The purpose of the calculating is to make a structural buckling analysis according to the code rules and the design requirements in order to judge whether the security injection tank have the ability to resist the buckling failure or not

  15. Study of irradiation creep of vanadium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Tsai, H.; Strain, R.V.; Smith, D.L. [Argonne National Lab., IL (United States)] [and others

    1997-08-01

    Thin-wall tubing was produced from the 832665 (500 kg) heat of V-4 wt.% Cr-4 wt.% Ti to study its irradiation creep behavior. The specimens, in the form of pressurized capsules, were irradiated in Advanced Test Reactor and High Flux Isotope Reactor experiments (ATR-A1 and HFIR RB-12J, respectively). The ATR-A1 irradiation has been completed and specimens from it will soon be available for postirradiation examination. The RB-12J irradiation is not yet complete.

  16. Comprehensive Creep and Thermophysical Performance of Refractory Materials

    Energy Technology Data Exchange (ETDEWEB)

    Ferber, M.K.; Wereszczak, A.; Hemrick, J.A.

    2006-06-29

    Furnace designers and refractory engineers recognize that optimized furnace superstructure design and refractory selection are needed as glass production furnaces are continually striving toward greater output and efficiencies. Harsher operating conditions test refractories to the limit, while changing production technology (such as the conversion to oxy-fuel from traditional air-fuel firing) can alter the way the materials perform [1-3]. Refractories for both oxy- and air-fuel fired furnace superstructures (see Fig. 1) are subjected to high temperatures that may cause them to creep excessively or subside during service if the refractory material is not creep resistant, or if it is subjected to high stress, or both. Furnace designers can ensure that superstructure structural integrity is maintained if the creep behavior of the refractory material is well understood and well represented by appropriate engineering creep models. Several issues limit the abilities of furnace designers to (1) choose the optimum refractory for their applications, (2) optimize the engineering design, or (3) predict the service mechanical integrity of their furnace superstructures. Published engineering creep data are essentially nonexistent for almost all commercially available refractories used for glass furnace superstructures. The limited data that do exist are supplied by the various refractory suppliers. Unfortunately, the suppliers generally have different ways of conducting their mechanical testing, and they interpret and report their data differently. This inconsistency makes it hard for furnace designers to draw fair comparisons between competing grades of candidate refractories. Furthermore, the refractory suppliers' data are often not available in a form that can be readily used for furnace design or for the prediction and design of long-term structural integrity of furnace superstructures. As a consequence, the U.S. Department of Energy (DOE) Industrial Technology Program

  17. Creep/Stress Rupture Behavior of 3D Woven SiC/SiC Composites with Sylramic-iBN, Super Sylramic-iBN and Hi-Nicalon-S Fibers at 2700F in Air

    Science.gov (United States)

    Bhatt, R. T.

    2017-01-01

    To determine the influence of fiber types on creep durability, 3D SiC/SiC CMCs were fabricated with Sylramic-iBN, super Sylramic-iBN and Hi-Nicalon-S fibers and the composite specimens were then tested under isothermal tensile creep at 14820C at 69, 103 and 138 MPa for up to 300hrs in air. The failed specimens were examined by scanning electron microscopy (SEM) and computed tomography (CT) for fracture mode analysis. The creep data of these composites are compared with those of other SiC/SiC composites in the literature. The results of this study will be presented.

  18. Buckled Graphene for Efficient Energy Harvest, Storage, and Conversion

    OpenAIRE

    Jiang, Jin-Wu

    2016-01-01

    Buckling is one of the most common phenomena in atomic-thick layered structures like graphene. While the buckling phenomenon usually causes disaster for most nano-devices, we illustrate one positive application of the buckled graphene for energy harvest, storage, and conversion. More specifically, we perform molecular dynamical simulations to show that the buckled graphene can be used to collect the wasted mechanical energy and store the energy in the form of internal knotting potential. Thro...

  19. Contemporary overview of soil creep phenomenon

    Directory of Open Access Journals (Sweden)

    Kaczmarek Łukasz

    2017-06-01

    Full Text Available Soil creep deformation refers to phenomena which take place in many areas and research in this field of science is rich and constantly developing. The article presents an analysis of the literature on soil creep phenomena. In light of the complexity of the issues involved and the wide variety of perspectives taken, this attempt at systematization seeks to provide a reliable review of current theories and practical approaches concerning creep deformation. The paper deals with subjects such as definition of creep, creep genesis, basic description of soil creep dynamics deformation, estimation of creep capabilities, various fields of creep occurrence, and an introduction to creep modeling. Furthermore, based on this analysis, a new direction for research is proposed.

  20. Significance of primary irradiation creep in graphite

    Energy Technology Data Exchange (ETDEWEB)

    Erasmus, Christiaan, E-mail: christiaan.erasmus@gmail.com [Pebble Bed Modular Reactor (Proprietary) Limited, PO Box 9396, Centurion 0046 (South Africa); Kok, Schalk [Advanced Mathematical Modelling, CSIR Modelling and Digital Science, Pretoria 0001 (South Africa); Hindley, Michael P. [Pebble Bed Modular Reactor (Proprietary) Limited, PO Box 9396, Centurion 0046 (South Africa)

    2013-05-15

    Traditionally primary irradiation creep is introduced into graphite analysis by applying the appropriate amount of creep strain to the model at the initial time-step. This is valid for graphite components that are subjected to high fast neutron flux fields and constant stress fields, but it does not allow for the effect of movement of stress locations around a graphite component during life, nor does it allow primary creep to be applied rate-dependently to graphite components subject to lower fast neutron flux. This paper shows that a differential form of primary irradiation creep in graphite combined with the secondary creep formulation proposed by Kennedy et al. performs well when predicting creep behaviour in experimental samples. The significance of primary irradiation creep in particular in regions with lower flux is investigated. It is shown that in low flux regions with a realistic operating lifetime primary irradiation creep is significant and is larger than secondary irradiation creep.

  1. Contemporary overview of soil creep phenomenon

    Science.gov (United States)

    Kaczmarek, Łukasz; Dobak, Paweł

    2017-06-01

    Soil creep deformation refers to phenomena which take place in many areas and research in this field of science is rich and constantly developing. The article presents an analysis of the literature on soil creep phenomena. In light of the complexity of the issues involved and the wide variety of perspectives taken, this attempt at systematization seeks to provide a reliable review of current theories and practical approaches concerning creep deformation. The paper deals with subjects such as definition of creep, creep genesis, basic description of soil creep dynamics deformation, estimation of creep capabilities, various fields of creep occurrence, and an introduction to creep modeling. Furthermore, based on this analysis, a new direction for research is proposed.

  2. Nonlinear buckling analyses of a small-radius carbon nanotube

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Ning, E-mail: liuxiao@ase.buaa.edu.cn; Li, Min; Jia, Jiao [School of Aeronautic Science and Engineering, Beihang University, Beijing 100091 (China); Wang, Yong-Gang [Department of Applied Mechanics, China Agricultural University, Beijing 100083 (China)

    2014-04-21

    Carbon nanotube (CNT) was first discovered by Sumio Iijima. It has aroused extensive attentions of scholars from all over the world. Over the past two decades, we have acquired a lot of methods to synthesize carbon nanotubes and learn their many incredible mechanical properties such as experimental methods, theoretical analyses, and computer simulations. However, the studies of experiments need lots of financial, material, and labor resources. The calculations will become difficult and time-consuming, and the calculations may be even beyond the realm of possibility when the scale of simulations is large, as for computer simulations. Therefore, it is necessary for us to explore a reasonable continuum model, which can be applied into nano-scale. This paper attempts to develop a mathematical model of a small-radius carbon nanotube based on continuum theory. An Isotropic circular cross-section, Timoshenko beam model is used as a simplified mechanical model for the small-radius carbon nanotube. Theoretical part is mainly based on modified couple stress theory to obtain the numerical solutions of buckling deformation. Meanwhile, the buckling behavior of the small radius carbon nanotube is simulated by Molecular Dynamics method. By comparing with the numerical results based on modified couple stress theory, the dependence of the small-radius carbon nanotube mechanical behaviors on its elasticity constants, small-size effect, geometric nonlinearity, and shear effect is further studied, and an estimation of the small-scale parameter of a CNT (5, 5) is obtained.

  3. Nonlinear buckling analyses of a small-radius carbon nanotube

    Science.gov (United States)

    Liu, Ning; Wang, Yong-Gang; Li, Min; Jia, Jiao

    2014-04-01

    Carbon nanotube (CNT) was first discovered by Sumio Iijima. It has aroused extensive attentions of scholars from all over the world. Over the past two decades, we have acquired a lot of methods to synthesize carbon nanotubes and learn their many incredible mechanical properties such as experimental methods, theoretical analyses, and computer simulations. However, the studies of experiments need lots of financial, material, and labor resources. The calculations will become difficult and time-consuming, and the calculations may be even beyond the realm of possibility when the scale of simulations is large, as for computer simulations. Therefore, it is necessary for us to explore a reasonable continuum model, which can be applied into nano-scale. This paper attempts to develop a mathematical model of a small-radius carbon nanotube based on continuum theory. An Isotropic circular cross-section, Timoshenko beam model is used as a simplified mechanical model for the small-radius carbon nanotube. Theoretical part is mainly based on modified couple stress theory to obtain the numerical solutions of buckling deformation. Meanwhile, the buckling behavior of the small radius carbon nanotube is simulated by Molecular Dynamics method. By comparing with the numerical results based on modified couple stress theory, the dependence of the small-radius carbon nanotube mechanical behaviors on its elasticity constants, small-size effect, geometric nonlinearity, and shear effect is further studied, and an estimation of the small-scale parameter of a CNT (5, 5) is obtained.

  4. 21 CFR 886.3300 - Absorbable implant (scleral buckling method).

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Absorbable implant (scleral buckling method). 886... SERVICES (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Prosthetic Devices § 886.3300 Absorbable implant (scleral buckling method). (a) Identification. An absorbable implant (scleral buckling method) is a...

  5. Vibration and Buckling of Web Plate of the Plate Girder

    OpenAIRE

    高橋, 和雄; 呉, 明強; 中澤, 聡志; 筑紫, 宏之

    1998-01-01

    The vibration and buckling of the web of the plate girder are studied in this paper. The small deflection theory of the thin plate is used. The finite strip method is employed to solve vibration and buckling of the plate girder. Natural frequenies of buckling properties are shown for various plate girder bridges.

  6. Buckling instability in amorphous carbon films

    Science.gov (United States)

    Zhu, X. D.; Narumi, K.; Naramoto, H.

    2007-06-01

    In this paper, we report the buckling instability in amorphous carbon films on mirror-polished sapphire (0001) wafers deposited by ion beam assisted deposition at various growth temperatures. For the films deposited at 150 °C, many interesting stress relief patterns are found, which include networks, blisters, sinusoidal patterns with π-shape, and highly ordered sinusoidal waves on a large scale. Starting at irregular buckling in the centre, the latter propagate towards the outer buckling region. The maximum length of these ordered patterns reaches 396 µm with a height of ~500 nm and a wavelength of ~8.2 µm. However, the length decreases dramatically to 70 µm as the deposition temperature is increased to 550 °C. The delamination of the film appears instead of sinusoidal waves with a further increase of the deposition temperature. This experimental observation is correlated with the theoretic work of Crosby (1999 Phys. Rev. E 59 R2542).

  7. Scleral Buckle Extrusion Associated with Phthisis

    Directory of Open Access Journals (Sweden)

    Tural Galbinur

    2011-01-01

    Full Text Available Exposure of implanted episcleral element is a rare complication of buckling procedures. We describe a 40-year-old man who presented to our clinic complaining of foreign body sensation and irritation in his left eye which lasted several months. The patient history was positive for bilateral rhegmatogenous retinal detachment which was treated with sclera buckling. Upon presentation the left eye demonstrated phthisis and an exposed and infected sclera buckle and explant in the lower quadrants. The explant was removed, and the patient was treated with antibiotics. This case suggests that wide encircling sclera element might erode through the conjunctiva of eyes undergoing phthisis. Integrity of the conjunctiva overlying episcleral implant should be evaluated during routine follow-up exams to exclude exposure of the implant particularly in eyes undergoing phthisis.

  8. Geometrically nonlinear creeping mathematic models of shells with variable thickness

    Directory of Open Access Journals (Sweden)

    V.M. Zhgoutov

    2012-08-01

    Full Text Available Calculations of strength, stability and vibration of shell structures play an important role in the design of modern devices machines and structures. However, the behavior of thin-walled structures of variable thickness during which geometric nonlinearity, lateral shifts, viscoelasticity (creep of the material, the variability of the profile take place and thermal deformation starts up is not studied enough.In this paper the mathematical deformation models of variable thickness shells (smoothly variable and ribbed shells, experiencing either mechanical load or permanent temperature field and taking into account the geometrical nonlinearity, creeping and transverse shear, were developed. The refined geometrical proportions for geometrically nonlinear and steadiness problems are given.

  9. (Irradiation creep of graphite)

    Energy Technology Data Exchange (ETDEWEB)

    Kennedy, C.R.

    1990-12-21

    The traveler attended the Conference, International Symposium on Carbon, to present an invited paper, Irradiation Creep of Graphite,'' and chair one of the technical sessions. There were many papers of particular interest to ORNL and HTGR technology presented by the Japanese since they do not have a particular technology embargo and are quite open in describing their work and results. In particular, a paper describing the failure of Minor's law to predict the fatigue life of graphite was presented. Although the conference had an international flavor, it was dominated by the Japanese. This was primarily a result of geography; however, the work presented by the Japanese illustrated an internal program that is very comprehensive. This conference, a result of this program, was better than all other carbon conferences attended by the traveler. This conference emphasizes the need for US participation in international conferences in order to stay abreast of the rapidly expanding HTGR and graphite technology throughout the world. The United States is no longer a leader in some emerging technologies. The traveler was surprised by the Japanese position in their HTGR development. Their reactor is licensed and the major problem in their graphite program is how to eliminate it with the least perturbation now that most of the work has been done.

  10. Development of Anti-Creep Andalusite-Based Bricks for Blast Furnace Stove

    Institute of Scientific and Technical Information of China (English)

    LIU Xiongzhang; ZHAO Huimin; CAO Hongfa

    2003-01-01

    Secondary mullitization and mineral phase compositions of reacting andalusite of different gain sizes with fine alumina powders are studied. By adopting reasonable process technology to control mullitization behavior during firing, good anti-creep andalusite bricks have been developed.

  11. STUDY THE CREEP OF TUBULAR SHAPED FIBER REINFORCED COMPOSITES

    Directory of Open Access Journals (Sweden)

    Najat J. Saleh

    2013-05-01

    Full Text Available Inpresent work tubular –shaped fiber reinforced composites were manufactured byusing two types of resins ( Epoxy and unsaturated polyester and separatelyreinforced with glass, carbon and kevlar-49 fibers (filament and woven roving,hybrid reinforcement composites of these fibers were also prepared. The fiberswere wet wound on a mandrel using a purposely designed winding machine,developed by modifying an ordinary lathe, in winding angle of 55° for filament. A creep test was made of either the fulltube or specimens taken from it. Creep was found to increase upon reinforcementin accordance to the rule of mixture and mainly decided by the type of singleor hybridized fibers. The creep behavior, showed that the observed strain tendsto appear much faster at higher temperature as compared with that exhibited atroom temperate. The creep rate also found to be depending on fiber type, matrixtype, and the fiber /matrix bonding. The creep energy calculated fromexperimental observations was found to exhibit highest value for hybridizedreinforcement.

  12. Creep in model pillars. [Salt, trona, and potash ore

    Energy Technology Data Exchange (ETDEWEB)

    Obert, L.

    1965-03-01

    A study was made of the deformational behavior (creep) of pillars made from three quasi-plastic rock--salt, trona, and potash ore. The first phase of this study considers the design of a model pillar suitable for creep tests; in the second phase, six model pillars were prepared from salt from two sources, from trona, and from potash ore. The pillars in each group were subjected to a different but constant axial stress, and the axial strain was measured for 1,000 hours. An analysis of the data shows that in general the creep rate for these model pillars can be expressed by the relationship .epsilon = K/sub 1/ sigma/sub 0//sup n/, where .epsilon is the strain rate, sigma/sub 0/ is the applied stress, and K/sub 1/ and n are constants. For the rocks included in this test, n ranged from 2.4 to 3.3.

  13. Creep of thermoplastic polyurethane reinforced with ozone functionalized carbon nanotubes

    Directory of Open Access Journals (Sweden)

    Z. Zhang

    2012-09-01

    Full Text Available This work focused on the mechanical behavior, especially creep resistance, of thermoplastic polyurethane (TPU filled with ozone-treated multi-walled carbon nanotubes (MWCNTs. It was found that the ozone functionalization of MWCNTs could improve their dispersion and interfacial adhesion to the TPU matrix as proved by scanning electron microscope and Raman spectrometer. It finally contributed to the enhancement of Young’s modulus and yield strength of TPU/MWCNT composites. Moreover, the creep resistance and recovery of MWCNT/TPU composites revealed a significant improvement by incorporating ozone functionalized MWCNTs. The strong interaction between the modified MWCNTs and TPU matrix would enhance the interfacial bonding and facilitate the load transfer, resulting in low creep strain and unrecovered strain.

  14. Overall buckling behavior of Q460 high strength steel welded box section columns under axial compression%Q460高强钢焊接箱形截面轴压构件整体稳定性能研究

    Institute of Scientific and Technical Information of China (English)

    班慧勇; 施刚; 石永久; 王元清

    2013-01-01

    为研究高强度钢材轴心受压钢柱的整体稳定性能,对5个国产Q460钢材焊接箱形截面柱进行了轴心受压试验研究.试验对试件的几何初弯曲、荷载初偏心以及截面的纵向残余应力分布均进行了测量.基于试验结果,分析了该类钢柱的失稳破坏形态和整体稳定承载力,建立了有限元分析模型并对试验结果进行模拟计算.研究结果表明:试件破坏模态均为整体弯曲失稳形态,大部分试件稳定承载力高于规范设计值;有限元分析模型能够准确地考虑几何初始缺陷和残余应力的影响,计算结果与试验结果吻合良好;通过与国内外钢结构设计规范的对比,提出了国产Q460高强钢焊接箱形截面轴压构件整体稳定设计的建议方法,即可以统一采用我国或欧洲规范的b类曲线进行设计,而不需要按板件宽厚比大小进行分类.%In order to investigate the overall buckling behavior of Q460 high strength steel columns under axial compression, 5 full-scale specimens were tested and the initial bending, loading eccentricity and sectional residual stress were also measured. Based on the experimental results, the failure mode and buckling capacity were clarified, and a finite element model was established to simulate the overall buckling behavior of such columns. It is found that the finite element model can well describe the effects caused by both initial geometric imperfections and residual stresses, and the calculated results through finite element analysis have a good agreement with experimental results. The validated model was further implemented for a large number of parametric analysis, and the calculated results were compared with different steel structure design codes. The design method for the overall buckling behavior of Q460 high strength steel welded box section columns was suggested, i. e. the column curve b in both GB 50017-2003 and Eurocode 3 can be employed to design such structural

  15. Compressive Creep Response of T1000G/RS-14 Graphite/Polycyanate Composite Materials

    Energy Technology Data Exchange (ETDEWEB)

    Starbuck, J.M.

    1998-01-01

    The response of a T1000G/RS-14 graphite/polycyanate composite material system to transverse compressive loads is quantified via experimentation. The primary objective of the work was to quantify the effects of process environment and test environment on the T1000G/RS-14 compressive creep response. Tests were conducted on both the neat resin and the composite material system. In addition to the creep tests, static compressive strength tests were conducted to define the stress-strain response. The creep behavior for the RS-14 resin was quantified by conducting a series of tests to study the effects of different process environments (air and nitrogen), different cure temperatures, and different test environments (air and vacuum). The combined effect on the RS-14 resin compressive creep of processing in nitrogen and testing under vacuum versus processing in air and testing in air was a 47% decrease in the creep strain after 2177 hr. The test environment appeared to have a greater effect on the resin creep than the process environment. Following the conclusion of the resin creep tests, composite transverse compressive creep tests were conducted. The composite creep test cylinder was post-cured in a nitrogen environment prior to machining test specimens and all tests were conducted in a vacuum environment. The series of tests investigated the effects of initial stress level and test temperature on the creep behavior. At the end of the 2000-hr tests at 275{degrees}F on specimens stressed at 10,000 psi, the nitrogen-processed and vacuum-tested conditions reduced the composite transverse compressive creep strain by 19% compared to processing in air and testing in air. The effects of process and test environment on the creep behavior are not as great for the composite system as they were for the neat resin, primarily because of the low resin content in the composite material system. At the 275{degrees}F test temperature there was a significant increase in the composite

  16. 薄壁波纹钢管混凝土柱局部屈曲性能研究%Study on the local buckling behavior of thin corrugated steel pipe concrete column

    Institute of Scientific and Technical Information of China (English)

    朱哲清; 高剑平; 罗民

    2014-01-01

    对一种新型的薄壁波纹钢管混凝土柱进行了低周反复荷载作用下滞回性能试验研究,然后利用ABAQUS进行模拟分析,分析了钢板截面宽厚比、长细比、钢板强度、混凝土强度等4个因素对薄壁波纹钢管混凝土柱局部屈曲的影响规律。试验结果表明:薄壁波纹钢管混凝土柱宽厚比、长细比基本与屈曲荷载成反比,钢板强度与屈曲荷载成正比,混凝土强度基本与屈曲荷载无关。%This paper presents an experimental research of hysteretic performance on a new kind of thin wall corrugated steel pipe concrete column under the effects of low cyclic load. The simulation analysis is carried on by ABAQUS towards the influence of such four factors as steel cross-section width-thickness ratio, slenderness ratio, steel strength, concrete strength on the thin wall corrugated steel pipe concrete column local buckling. The main conclusions are as follows: there is an inverse correlation between its width to thickness ratio, slenderness ratio and local buckling load; steel strength is proportional to the load; concrete strength has no effect on the load.

  17. Nonlocal modeling and buckling features of cracked nanobeams with von Karman nonlinearity

    Science.gov (United States)

    Akbarzadeh Khorshidi, Majid; Shaat, Mohamed; Abdelkefi, Abdessattar; Shariati, Mahmoud

    2017-01-01

    Buckling and postbuckling behaviors of cracked nanobeams made of single-crystalline nanomaterials are investigated. The nonlocal elasticity theory is used to model the nonlocal interatomic effects on the beam's performance accounting for the beam's axial stretching via von Karman nonlinear theory. The crack is then represented as torsional spring where the crack severity factor is derived accounting for the nonlocal features of the beam. By converting the beam into an equivalent infinite long plate with an edge crack subjected to a tensile stress at the far field, the crack energy release rate, intensity factor, and severity factor are derived according to the nonlocal elasticity theory. An analytical solution for the buckling and the postbuckling responses of cracked nonlocal nanobeams accounting for the beam axial stretching according to von Karman nonlinear theory of kinematics is derived. The impacts of the nonlocal parameter on the critical buckling loads and the static nonlinear postbuckling responses of cracked nonlocal nanobeams are studied. The results indicate that the buckling and postbuckling behaviors of cracked nanobeams are strongly affected by the crack location, crack depth, nonlocal parameter, and length-to-thickness ratio.

  18. Buckling and postbuckling of radially loaded microtubules by nonlocal shear deformable shell model.

    Science.gov (United States)

    Shen, Hui-Shen

    2010-05-21

    This paper presents an investigation on the buckling and postbuckling of microtubules (MTs) subjected to a uniform external radial pressure in thermal environments. The microtubule is modeled as a nonlocal shear deformable cylindrical shell which contains small scale effects. The governing equations are based on higher order shear deformation shell theory with a von Kármán-Donnell-type of kinematic nonlinearity and include the extension-twist and flexural-twist couplings. The thermal effects are also included and the material properties are assumed to be temperature-dependent. A singular perturbation technique is employed to determine the buckling pressure and postbuckling equilibrium paths. The small scale parameter e(0)a is estimated by matching the buckling pressure of MTs measured from the experiments with the numerical results obtained from the nonlocal shear deformable shell model. The numerical results show that buckling pressure and postbuckling behavior of MTs are very sensitive to the small scale parameter e(0)a. The results reveal that the 13_3 microtubule has a stable postbuckling path, whereas the 13_2 microtubule has an unstable postbuckling behavior due to the presence of skew angles.

  19. Buckling modes of elastic thin films on elastic substrates

    Science.gov (United States)

    Mei, Haixia; Huang, Rui; Chung, Jun Young; Stafford, Christopher M.; Yu, Hong-Hui

    2007-04-01

    Two buckling modes have been observed in thin films: buckle delamination and wrinkling. This letter identifies the conditions for selecting the favored buckling modes for elastic films on elastic substrates. Transition from one buckling mode to another is predicted as the stiffness ratio between the substrate and the film or is predicted for variation of the stiffness ratio between the substrate and the film or variation of theinterfacial defect size. The theoretical results are demonstrated experimentally by observing the coexistence of both buckling modes and mode transition in one film-substrate system.

  20. Nano-scaled diffusional or dislocation creep analysis of single-crystal ZnO

    Directory of Open Access Journals (Sweden)

    P. H. Lin

    2016-09-01

    Full Text Available The nanoindentation time-dependent creep experiments with different peak loads are conducted on c-plane (0001, a-plane (112¯0 and m-plane (101¯0 of single-crystal ZnO. Under nano-scaled indentation, the creep behavior is crystalline orientation-dependent. For the creep on (0001, the stress exponent at low loads is ∼1 and at high loads ∼4. The stress exponents under all loads are within 3∼7 for the creep on (112¯0 and (101¯0. This means that diffusion mechanism and dislocation mechanism is operative for different planes and loads. The relative difficulty of dislocations activation is an additional factor leading to the occurring of diffusion creep on the c-plane of single-crystal ZnO.

  1. Microstructural evolution in a Ti-Ta high-temperature shape memory alloy during creep

    Energy Technology Data Exchange (ETDEWEB)

    Rynko, Ramona; Marquardt, Axel; Pauksen, Alexander; Frenzel, Jan; Somsen, Christoph; Eggeler, Gunther [Bochum Univ. (Germany). Inst. for Materials

    2015-04-15

    Alloys based on the titanium-tantalum system are considered for application as high-temperature shape memory alloys due to their martensite start temperatures, which can surpass 200 C. In the present work we study the evolution of microstructure and the influence of creep on the phase transformation behavior of a Ti{sub 70}Ta{sub 30} (at.%) high-temperature shape memory alloy. Creep tests were performed in a temperature range from 470 to 530 C at stresses between 90 and 150 MPa. The activation energy for creep was found to be 307 kJ mol{sup -1} and the stress exponent n was determined as 3.7. Scanning and transmission electron microscopy investigations were carried out to characterize the microstructure before and after creep. It was found that the microstructural evolution during creep suppresses subsequent martensitic phase transformations.

  2. Some aspects of anelastic and microplastic creep of pure Al and two Al-alloys

    Energy Technology Data Exchange (ETDEWEB)

    Sgobba, S. (Lab. de Metallurgie Mecanique, Dept. des Materiaux, Ecole Polytechnique Federale de Lausanne (Switzerland)); Kuenzi, H.U. (Lab. de Metallurgie Mecanique, Dept. des Materiaux, Ecole Polytechnique Federale de Lausanne (Switzerland)); Ilschner, B. (Lab. de Metallurgie Mecanique, Dept. des Materiaux, Ecole Polytechnique Federale de Lausanne (Switzerland))

    1993-11-01

    Anelastic creep of pure Al, commercial Al-Cu and a binary Al-Cu alloy has been measured at room temperature by means of a high resolution laser interferometer. The irreversible component of the deformation was also quantified from measurements of the anelastic creep recovery. The dependence of the deformation-time curves on thermal treatment and cold work is analyzed. The mechanisms responsible for the room temperature anelastic creep are discussed. Materials loaded below their elastic limit can present either a pure anelastic behavior (commercial Al-Cu) or additional viscoelastic creep (pure Al, high purity Al-Cu). For commercial Al-Cu, the presence of an irreversible deformation appears to be mainly related to the state of the surface. A viscoelastic after effect has been measured for this alloy after a Cu-electroplating treatment. As a typical result for room temperature creep, the irreversible deformation depends logarithmically on load time. (orig.).

  3. Observations of orientation dependent creep of Ni{sub 3}Al

    Energy Technology Data Exchange (ETDEWEB)

    Knobloch, C.; Glock, K.; Glatzel, U.

    1999-07-01

    The influence of crystal orientation on the high temperature creep behavior of Ni{sub 3}(Al Ti Ta) was investigated by tensile creep testing under a constant load at a temperature of 1,123K. The single crystals were oriented close to [001], [011], [111], [557] and [012]. The results show an increasing stationary creep rate from [111] over [011] to [001]. The evolution of the microstructure during creep deformation was studied, using transmission electron microscopy (TEM). Only few systems are active in the primary regime, whereas several slip systems operate in the secondary stage. habit planes of dislocation pairs separated by an antiphase boundary were examined and compared with anisotropic elastic calculations, explaining the good creep response of [111] oriented using crystals.

  4. Equilibrium equations for nonlinear buckling analysis of drill-strings in 3D curved well-bores

    Institute of Scientific and Technical Information of China (English)

    TAN MeiLan; GAN LiFei

    2009-01-01

    With the development of drilling technology, the oil/gas well has evolved from its early vertical straight form to the inclined, horizontal, plane curved, or even 3D curved well-bore. Understanding of the buck-ling behavior of a drill-string in a well-bore is crucial for the success of a drilling operation. Therefore, equilibrium equations for analyzing the buckling behavior of a drill-string in a 3D curved well-bore are required. Based on Love's equilibrium equations for a curved and twisted rod in space, s set of equi-librium equations for the nonlinear buckling analysis of a drill-string in a 3D curved well-bore are de-rived by introducing a radial constraint of the well-bore. The proposed formulae can account for the well curvature and tortuosity. Thus, it can be used to analyze the buckling behaviors of a drill-string constrained in a well-bore and subjected to axial compression, torsion at its upper end, and gravity simultaneously. It is worth noting that the existing equations in the literature for a drill-string in a straight and plane curved well-bore with a constant curvature are a special case of the proposed model. Thus, the present model can provide s theoretical basis for the nonlinear buckling analysis of a drill-string constrained in a 3D curved well-bore.

  5. Temperature dependence of creep compliance of highly cross-linked epoxy: A molecular simulation study

    Energy Technology Data Exchange (ETDEWEB)

    Khabaz, Fardin, E-mail: rajesh.khare@ttu.edu; Khare, Ketan S., E-mail: rajesh.khare@ttu.edu; Khare, Rajesh, E-mail: rajesh.khare@ttu.edu [Department of Chemical Engineering, Texas Tech University, Lubbock, TX 79409 (United States)

    2014-05-15

    We have used molecular dynamics (MD) simulations to study the effect of temperature on the creep compliance of neat cross-linked epoxy. Experimental studies of mechanical behavior of cross-linked epoxy in literature commonly report creep compliance values, whereas molecular simulations of these systems have primarily focused on the Young’s modulus. In this work, in order to obtain a more direct comparison between experiments and simulations, atomistically detailed models of the cross-linked epoxy are used to study their creep compliance as a function of temperature using MD simulations. The creep tests are performed by applying a constant tensile stress and monitoring the resulting strain in the system. Our results show that simulated values of creep compliance increase with an increase in both time and temperature. We believe that such calculations of the creep compliance, along with the use of time temperature superposition, hold great promise in connecting the molecular insight obtained from molecular simulation at small length- and time-scales with the experimental behavior of such materials. To the best of our knowledge, this work is the first reported effort that investigates the creep compliance behavior of cross-linked epoxy using MD simulations.

  6. Creep Behaviour of Modified Mar-247 Superalloy

    Directory of Open Access Journals (Sweden)

    Cieśla M.

    2016-06-01

    Full Text Available The paper presents the results of analysis of creep behaviour in short term creep tests of cast MAR-247 nickel-based superalloy samples made using various modification techniques and heat treatment. The accelerated creep tests were performed under temperature of 982 °C and the axial stresses of σ = 150 MPa (variant I and 200 MPa (variant II. The creep behaviour was analysed based on: creep durability (creep rupture life, steady-state creep rate and morphological parameters of macro- and microstructure. It was observed that the grain size determines the creep durability in case of test conditions used in variant I, durability of coarse-grained samples was significantly higher.

  7. Lower Bound Approximation for Elastic Buckling Loads

    NARCIS (Netherlands)

    Vrouwenvelder, A.; Witteveen, J.

    1975-01-01

    An approximate method for the elastic buckling analysis of two-dimensional frames is introduced. The method can conveniently be explained with reference to a physical interpretation: In the frame every member is replaced by two new members: - a flexural member without extensional rigidity to transmi

  8. Buckling in quasi-2D polymers

    NARCIS (Netherlands)

    Edmondson, S; Frieda, K; Comrie, JE; Onck, PR; Huck, WTS

    2006-01-01

    Buckle-driven delamination and subsequent collapse of strained thin polymer films upon triggered release from the substrate is exploited to fabricate striking, well-defined ridging patterns (see figure). An analysis of these patterns is presented, including the effects of film thickness and the exte

  9. Critical Buckling Load on Large Spherical Shells

    DEFF Research Database (Denmark)

    Wedellsborg, B. W.

    1962-01-01

    Approximate evaluation for watertanks, hortonspheres, vapor containers, containment vessels for nuclear reactors, and so forth, has been computed, taking into account out-of-roundness and local flattened areas; graphs have been plotted giving critical buckling load as function of maximum radial...

  10. Dynamic Pulse Buckling--Theory and Experiment

    Science.gov (United States)

    1983-02-01

    34Buckling of Bars Subject to Axial Shock," Studii si Cercetari de Mecanica Applicata (Roumania), 7, 1, pp. 173-178, January 1956. 26. A.F. Schmitt, "A...Procopovici, "Transverse Deformation of an Elastic Bar Subjected to an Axial Impulsive Force," Studii si Ceretari de Mecanica Applicata. 8, 3, pp. 839

  11. Robust simulation of buckled structures using reduced order modeling

    Science.gov (United States)

    Wiebe, R.; Perez, R. A.; Spottswood, S. M.

    2016-09-01

    Lightweight metallic structures are a mainstay in aerospace engineering. For these structures, stability, rather than strength, is often the critical limit state in design. For example, buckling of panels and stiffeners may occur during emergency high-g maneuvers, while in supersonic and hypersonic aircraft, it may be induced by thermal stresses. The longstanding solution to such challenges was to increase the sizing of the structural members, which is counter to the ever present need to minimize weight for reasons of efficiency and performance. In this work we present some recent results in the area of reduced order modeling of post- buckled thin beams. A thorough parametric study of the response of a beam to changing harmonic loading parameters, which is useful in exposing complex phenomena and exercising numerical models, is presented. Two error metrics that use but require no time stepping of a (computationally expensive) truth model are also introduced. The error metrics are applied to several interesting forcing parameter cases identified from the parametric study and are shown to yield useful information about the quality of a candidate reduced order model. Parametric studies, especially when considering forcing and structural geometry parameters, coupled environments, and uncertainties would be computationally intractable with finite element models. The goal is to make rapid simulation of complex nonlinear dynamic behavior possible for distributed systems via fast and accurate reduced order models. This ability is crucial in allowing designers to rigorously probe the robustness of their designs to account for variations in loading, structural imperfections, and other uncertainties.

  12. Standard test method for measurement of creep crack growth times in metals

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2007-01-01

    1.1 This test method covers the determination of creep crack growth (CCG) in metals at elevated temperatures using pre-cracked specimens subjected to static or quasi-static loading conditions. The time (CCI), t0.2 to an initial crack extension δai = 0.2 mm from the onset of first applied force and creep crack growth rate, ˙a or da/dt is expressed in terms of the magnitude of creep crack growth relating parameters, C* or K. With C* defined as the steady state determination of the crack tip stresses derived in principal from C*(t) and Ct (1-14). The crack growth derived in this manner is identified as a material property which can be used in modeling and life assessment methods (15-25). 1.1.1 The choice of the crack growth correlating parameter C*, C*(t), Ct, or K depends on the material creep properties, geometry and size of the specimen. Two types of material behavior are generally observed during creep crack growth tests; creep-ductile (1-14) and creep-brittle (26-37). In creep ductile materials, where cr...

  13. Effect of creep-aging on precipitates of 7075 aluminum alloy

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Y.C., E-mail: yclin@csu.edu.cn [School of Mechanical and Electrical Engineering, Central South University, Changsha 410083 (China); State Key Laboratory of High Performance Complex Manufacturing, Changsha 410083 (China); State Key Laboratory of Material Processing and Die and Mould Technology, Wuhan 430074 (China); Jiang, Yu-Qiang; Chen, Xiao-Min; Wen, Dong-Xu [School of Mechanical and Electrical Engineering, Central South University, Changsha 410083 (China); State Key Laboratory of High Performance Complex Manufacturing, Changsha 410083 (China); Zhou, Hua-Min [State Key Laboratory of Material Processing and Die and Mould Technology, Wuhan 430074 (China)

    2013-12-20

    The creep-aging behaviors of 7075 aluminum alloy are studied by uniaxial tensile creep experiments under elevated temperatures. The effects of creep-aging temperature and applied stress on the precipitates of 7075-T651 aluminum alloy are investigated using a scanning electron microscope (SEM) and a transmission electron microscope (TEM). Results show that (1) coarse insoluble precipitates (Al{sub 7}Cu{sub 2}Fe and Mg{sub 2}Si) and intermediate precipitates (Al{sub 18}Mg{sub 3}Cr{sub 2} and Al{sub 3}Zr) are found in the aluminum matrix, and the effects of creep-aging treatment on these precipitates are not obvious; (2) the main aging precipitates are η′ and η phases, and the amount of aging precipitates increase with the increase of creep-aging temperature and applied stress; (3) with the increase of creep-aging temperature and applied stress, the precipitates are discontinuously distributed on the grain boundary, and the width of precipitate free zone increases with the increase of creep-aging temperature and applied stress and (4) compared with the microstructure in the traditional stress-free aged sample, the creep-aging process can refine the precipitates and narrow the width of the precipitate free zone.

  14. Irradiation creep of nano-powder sintered silicon carbide at low neutron fluences

    Science.gov (United States)

    Koyanagi, T.; Shimoda, K.; Kondo, S.; Hinoki, T.; Ozawa, K.; Katoh, Y.

    2014-12-01

    The irradiation creep behavior of nano-powder sintered silicon carbide was investigated using the bend stress relaxation method under neutron irradiation up to 1.9 dpa. The creep deformation was observed at all temperatures ranging from 380 to 1180 °C mainly from the irradiation creep but with the increasing contributions from the thermal creep at higher temperatures. The apparent stress exponent of the irradiation creep slightly exceeded unity, and instantaneous creep coefficient at 380-790 °C was estimated to be ∼1 × 10-5 [MPa-1 dpa-1] at ∼0.1 dpa and 1 × 10-7 to 1 × 10-6 [MPa-1 dpa-1] at ∼1 dpa. The irradiation creep strain appeared greater than that for the high purity SiC. Microstructural observation and data analysis indicated that the grain-boundary sliding associated with the secondary phases contributes to the irradiation creep at 380-790 °C to 0.01-0.11 dpa.

  15. Fluência em filtros cerâmicos de Al2O3 Creep in Al2O3 ceramic filters

    Directory of Open Access Journals (Sweden)

    V. R. Salvini

    2001-12-01

    Full Text Available O comportamento de fluência em materiais cerâmicos sólidos é afetado pela sua microestrutura. Fundamentalmente, são três os parâmetros que influenciam o comportamento de fluência nestes materiais: o constituinte mineralógico, a fase vítrea e a porosidade. Além destes fatores microestruturais, a fluência em cerâmicas celulares depende também da sua macroestrutura, constituída de um arranjo tridimensional de filamentos sólidos interligados. Assim, a análise dos resultados de fluência nestes materiais compreende duas etapas: na primeira deve-se identificar o modo de deformação dos filamentos cerâmicos (macroestrutura e na segunda, identificar o(s mecanismo(s de fluência da microestrutura através dos parâmetros n (expoente da tensão aplicada e Q (energia de ativação do processo. Neste trabalho avaliou-se a fluência em filtros cerâmicos de Al2O3 de 10 ppi sob compressão de 0,034; 0,051 e 0,068 MPa às temperaturas de 1500, 1550 e 1600 ºC ao ar. De acordo com os resultados obtidos, supõe-se que o modo de deformação por flambagem dos filamentos paralelos a carga aplicada é um dos principais fatores que contribui para o aumento da taxa de deformação do filtro e, portanto, dos valores de n e Q. Além do modo de deformação dos filamentos, observou-se que o tipo de ensaio de fluência (com ou sem troca de carga também influencia a determinação dos valores de n e Q.The creep behavior of solid ceramics is strongly affected by the microstructure. Fundamentally, there are three microstructural features which influence the creep behavior: the mineral content, the flux content and the apparent porosity. Additionally, the creep of cellular ceramics also depends on their macrostructure constituted by a tridimensional array of struts. Therefore, the creep analysis of these materials should consist of two stages. Firstly, identification of the macrostructure deformation mode and secondly, determination of the stress exponent

  16. Creep Behavior of Oxide/Oxide Composites with Monazite Fiber Coating at 1100 deg C in Air and in Steam Environments

    Science.gov (United States)

    2008-09-01

    tensometer was equipped with 6-inch alumina contact rods and protected by a heat shield to maintain the unit temperatures within the manufacturers...R.J. “Crack deflection in ceramic composites and fiber coating design criteria”. Composites: Part A, 30:521–524, 1999. 20. K.K., Chawla. Ceramic MAtrix...Behavior of NextelTM720/ Alumina (N720/A) Continuous Fiber Ceramic Composite”. Composites Part A: Applied Science and Manufacturing, 37:2029–2040, 2006

  17. Thermal Creep Force: Analysis And Application

    Science.gov (United States)

    2016-06-01

    Calhoun: The NPS Institutional Archive Theses and Dissertations Thesis and Dissertation Collection 2016-06 Thermal creep force: analysis and...CALIFORNIA DISSERTATION Approved for public release; distribution is unlimited THERMAL CREEP FORCE: ANALYSIS AND APPLICATION by David...blank) 2. REPORT DATE June 2016 3. REPORT TYPE AND DATES COVERED Doctoral Dissertation 4. TITLE AND SUBTITLE THERMAL CREEP FORCE: ANALYSIS

  18. Influence of precipitate morphology on intermediate temperature creep properties of a nickel-base superalloy single crystal

    Science.gov (United States)

    Nathal, M. V.; Mackay, R. A.; Miner, R. V.

    1989-01-01

    The relative creep behavior of cuboidal (as-heat treated) and rafted (precrept at 1000 C) gamma-prime microstructures in the single-crystal Ni-based superalloy NASAIR 100 at 760 C was investigated using SEM and TEM examinations of materials at various stages of creep. It was found that, at high applied stresses, the crystals with cuboidal gamma-prime structure had both lower minimum creep rates and longer rupture lives than the crystals with lamellar gamma-prime. At lower stress levels, the initially cuboidal gamma-prime microstructure maintained a lower creep rate, but exhibited a similar rupture life compared to the prerafted crystals.

  19. 等通道转角挤压ZK31+4Si镁合金的显微组织及高温蠕变行为%Microstructure and Creep Behavior of ECAPed ZK31+4Si Magnesium Alloy

    Institute of Scientific and Technical Information of China (English)

    周旭阳; 梁伟; 韩富银; 谢国印

    2012-01-01

    研究ZK31 +4Si镁合金经等通道转角挤压(ECAP)后的微观组织和高温蠕变行为.结果表明,ECAP挤压可显著细化原铸态组织中粗大的汉字状Mg2Si相,并使其趋于均匀弥散分布.ECAP挤压后试样的抗蠕变性能明显优于铸态试样,在温度为473 K,应力为70MPa的条件下,8道次挤压试样的稳态蠕变速率约为铸态试样的1/15,蠕变寿命提高近8倍.由稳态蠕变速率与应力的对数曲线关系求得473 K下4道次挤压和8道次挤压试样的应力指数n均约为4,同时按位错蠕变机制,当应力指数n=4时,理论计算所得稳态蠕变速率与实验值非常吻合,说明在本实验条件下发生的是位错蠕变.%The microstructures and the creep behavior of ZK31+4Si magnesium alloy processed by Equal channel angular pressing (ECAP) were investigated. The experimental results show that the coarse Chinese script-like Mg2Si precipitates are refined to fine polygonal shape particles and redistributed dispersedly after ECAP. The creep resistance is greatly enhanced after ECAP. The ctable creep rate of the 8-pass ECAPed specimen is nearly 1/15 of that of the as-cast one, and its creep life is increased by about S times. The curves of the minimum strain rate versus the stress show that the alloy ECAPed either through 8 passes or through 4 passes exhibit a same stress exponent n≈4. Furthermore, the theoretical calculation results according to the dislocation creep model with n=4 are well in agreement with the experimental values, indicating that the creep under the present test condition is controlled by the movement of dislocations.

  20. Effects of Heat-Treated Wood Particles on the Physico-Mechanical Properties and Extended Creep Behavior of Wood/Recycled-HDPE Composites Using the Time–Temperature Superposition Principle

    Directory of Open Access Journals (Sweden)

    Teng-Chun Yang

    2017-03-01

    Full Text Available This study investigated the effectiveness of heat-treated wood particles for improving the physico-mechanical properties and creep performance of wood/recycled-HDPE composites. The results reveal that the composites with heat-treated wood particles had significantly decreased moisture content, water absorption, and thickness swelling, while no improvements of the flexural properties or the wood screw holding strength were observed, except for the internal bond strength. Additionally, creep tests were conducted at a series of elevated temperatures using the time–temperature superposition principle (TTSP, and the TTSP-predicted creep compliance curves fit well with the experimental data. The creep resistance values of composites with heat-treated wood particles were greater than those having untreated wood particles due to the hydrophobic character of the treated wood particles and improved interfacial compatibility between the wood particles and polymer matrix. At a reference temperature of 20 °C, the improvement of creep resistance (ICR of composites with heat-treated wood particles reached approximately 30% over a 30-year period, and it increased significantly with increasing reference temperature.