WorldWideScience

Sample records for cotton gin trash

  1. Pilot scale cotton gin trash energy recovery

    Energy Technology Data Exchange (ETDEWEB)

    Harp, S.L. [Oklahoma State Univ., Stillwater, OK (United States)

    1993-12-31

    During the summer of 1992 a 520,000 kcal/h (2,064,400 Btu/hr) biomass combustor was installed at a cotton gin in southwestern Oklahoma. The gin has a capacity of approximately 35 bales per hour. Each bale of cotton ginned weighs about 227 kg (500 lb) and produces about 68 kg (150 lb) of trash. Therefore, this gin produces about 52,360 kg (115,500 lb) of trash per day during a typical ginning season. Approximately 2 million kg (4 million lb) of gin trash are produced at this site each year. Cotton must first be dried to about 3-5% moisture content before the ginning process is begun. To accomplish this at this gin, two six million Btu/hour direct fired gas heaters are used to heat air for drying the cotton. The biomass combustor was installed to operate in parallel with one of the heaters to supply heated air for the drying process. A pneumatic conveying system was installed to intercept a portion of the gin trash and divert it to the burner. The burner was operated during the 1992 ginning season, which lasted from September through November, with few problems.

  2. Cotton gin trash in the western United States: Resource inventory and energy conversion characterization

    Energy Technology Data Exchange (ETDEWEB)

    Haase, S.G.; Quinn, M.W.; Whittier, J.P. [NEOS Corp., Lakewood, CO (United States); Cohen, T.M.; Lansford, R.R. [New Mexico State Univ., Las Cruces, NM (United States); Craig, J.D. [Cratech Inc., Tahoka, TX (United States); Swanson, D.S.; Morgan, G. [Western Regional Biomass Energy Program, Golden, CO (United States)

    1993-12-31

    The disposal of wastes associated with the processing of cotton is posing increasing problems for cotton gin operators in the western United States. Traditional disposal methods, such as open-air incineration and landfilling are no longer adequate due to increasing environmental concerns. This paper evaluates the technical, economic and environmental feasibility for cotton gin trash to serve as an energy resource. Cotton gin trash has been quantified, by county, in the five cotton-growing states of the western United States. The energy conversion technology that appears to offer the most promise is gasification. An economic evaluation model has been developed that will allow gin operators to analyze their own situation to determine the profitability of converting gin trash to energy.

  3. Non-contact image processing for gin trash sensors in stripper harvested cotton with burr and fine trash correction

    Science.gov (United States)

    This study was initiated to provide the basis for obtaining online information as to the levels of the various types of gin trash. The objective is to provide the ginner with knowledge of the quantity of the various trash components in the raw uncleaned seed cotton. This information is currently not...

  4. Mote trash system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  5. Master trash system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  6. Fourier transform infrared macro-imaging of botanical cotton trash

    Science.gov (United States)

    The marketability of cotton fiber is directly tied to the trash comingled with it. Trash can contaminate cotton during harvesting, ginning, and processing. Thus, the removal of trash is important from field to fabric. An ideal prerequisite to removing trash from lint is identifying what trash types...

  7. Fluidized bed gasification of high tonnage sorghum, cotton gin trash and beef cattle manure: Evaluation of synthesis gas production

    International Nuclear Information System (INIS)

    Maglinao, Amado L.; Capareda, Sergio C.; Nam, Hyungseok

    2015-01-01

    Highlights: • High tonnage sorghum, cotton gin trash and beef cattle manure were characterized and gasified in a fluidized bed reactor. • Biomass gasification at 730 °C and ER = 0.35 produced synthesis gas with an average energy content of 4.19 MJ Nm −3 . • Synthesis gas heating value and yield were relatively constant at reaction temperatures from 730 °C to 800 °C. • Optimum hydrogen production on HTS gasification was achieved at 780 °C temperature and ER of 0.4. - Abstract: Fluidized bed gasification using high-tonnage sorghum, cotton gin trash and beef cattle manure was performed in a pilot scale bubbling fluidized bed reactor equipped with the necessary feedback control system. Characterization of biomass showed that the high-tonnage sorghum had the highest energy and carbon content of 19.58 MJ kg −1 and 42.29% wt , respectively among the three feed stocks. At 730 °C reaction temperature and equivalence ratio of 0.35, comparable yields of methane, nitrogen and carbon dioxide (within ± 1.4% vol ) were observed in all three feed stocks. The gasification system produced synthesis gas with an average heating value of 4.19 ± 0.09 MJ Nm −3 and an average yield of 1.98 ± 0.1 Nm 3 kg −1 of biomass. Carbon conversion and gasification efficiencies indicated that most of the carbon was converted to gaseous products (85% average ) while 48% average of the energy from the biomass was converted into combustible gas. The production of hydrogen was significantly affected by the biomass used during gasification. The synthesis gas heating value and yield were relatively constant at reaction temperatures from 730 °C to 800 °C. Utilizing high-tonnage sorghum, the optimum hydrogen production during gasification was achieved at a reaction temperature of 780 °C and an equivalence ratio of 0.40.

  8. Biological control agent of larger black flour beetles (Coleoptera: Tenebrionidae): A nuisance pest developing in cotton gin trash piles.

    Science.gov (United States)

    Larger black flour beetles (LBFB), Cynaeus angustus, feed on saprophytic fungi found in gin trash piles, and become nuisance pests in homes and businesses. We examined the dose-response of three entomopathogenic nematode species (Steinernema carpocapsae, S. feltiae, and Heterorhabditis bacteriophora...

  9. 7 CFR 319.8-9 - Hull fiber and gin trash.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 5 2010-01-01 2010-01-01 false Hull fiber and gin trash. 319.8-9 Section 319.8-9 Agriculture Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION... Importation and Entry of Cotton and Covers § 319.8-9 Hull fiber and gin trash. (a) Entry of hull fiber will be...

  10. Energy usage for cotton ginning in Australia

    Energy Technology Data Exchange (ETDEWEB)

    Ismail, S.A. [MARA Univ. of Technology, Shah Alam (Malaysia). Faculty of Applied Sciences; Southern Queensland Univ., Toowoomba, QLD (Australia). National Centre for Engineering in Agriculture; Chen, G.; Baillie, C.; Symes, T. [Southern Queensland Univ., Toowoomba, QLD (Australia). National Centre for Engineering in Agriculture

    2010-07-01

    This paper reported on a study that evaluated the energy consumption of cotton gins used in Australia. The average electricity use is 52.3 kWh per bale. In practicality, the electricity consumption for different gins is correlated linearly with the bale numbers produced. The cost of electricity is therefore important in cotton ginning operations. The power factor in all the gins monitored in this study was greater than 0.85. The study showed that the use of gas dryers was highly influenced by the cotton moisture and regulated drying temperature. In general, electricity and gas consumption comprised 61 and 39 per cent of total energy use respectively. The study showed that 60.38 kg of carbon dioxide are emitted for ginning each bale of cotton. This paper described a newly developed method for monitoring the energy performance in cotton gins. Detailed monitoring and analysis carried out at 2 gin sites revealed that electricity consumption is not influenced much by changes in trash content in the module, degree of moisture and lint quality. However, the cotton variety influences the energy consumption. Cotton handling constituted nearly 50 per cent of the power used in both gins.

  11. Effects of Pyrolysis Temperature on Product Yields and Energy Recovery from Co-Feeding of Cotton Gin Trash, Cow Manure, and Microalgae: A Simulation Study

    Science.gov (United States)

    Hanif, Muhammad Usman; Capareda, Sergio C.; Iqbal, Hamid; Arazo, Renato Ortiz; Baig, Muhammad Anwar

    2016-01-01

    The intensive search of new and cleaner energy catches interest in recent years due to huge consumption of fossil fuels coupled with the challenge of energy and environmental sustainability. Production of renewable and environmentally benign energy from locally available raw materials is coming in the frontline. In this work, conversion of the combined biomass (cotton gin trash, cow manure, and Microalgae [Nannochloropsis oculata]) through batch pyrolysis has been investigated. The effect of temperature to the production of energy fuels such as bio-oil, char, and biogas have been simulated considering the yield and energy content as responses. Result of the investigation generally revealed that the proportions of the different biomass did not significantly affect the product yield and energy recovery. Significant effect of temperature is evident in the simulation result of energy recovery whereby maximum conversion was achieved at 400°C for char (91 wt%), 600°C for syngas (22 wt%), and 551°C for bio-oil (48 wt%). Overall energy conversion efficiency of 75.5% was obtained at 589°C in which 15.6 MJ/kg of mixed biomass will be elevated to pyrolysis products. PMID:27043929

  12. Fourier-transform imaging of cotton and botanical and field trash mixtures

    Science.gov (United States)

    Botanical and field cotton trash comingled with cotton lint can greatly reduce the marketability and quality of cotton. Trash can be found comingled with cotton lint during harvesting, ginning, and processing, thus this study is of interest. Attenuated Total Reflectance-Fourier Transform Infrared (A...

  13. Image processing for stripper harvested cotton trash content measurement a progress report

    Science.gov (United States)

    This study was initiated to provide the basis for obtaining on-line information as to the levels of the various types of gin trash. The objective is to provide the ginner with knowledge of the quantity of the various trash components in the raw uncleaned seed cotton. This information is currently no...

  14. Cotton gin electrical energy use trends and 2009 audit results

    Science.gov (United States)

    Cotton gin energy costs have risen more than other operating costs. Energy audits were conducted in twenty US cotton gins representing a range of capacities in six states. The average participating saw gin used 39.5 kWh to process a bale. The average roller gin used 62.6 kWh. Gins have become la...

  15. Dictionary of cotton: Picking & ginning

    Science.gov (United States)

    Cotton is an essential commodity for textiles and has long been an important item of trade in the world’s economy. Cotton is currently grown in over 100 countries by an estimated 100 producers. The basic unit of the cotton trade is the cotton bale which consists of approximately 500 pounds of raw c...

  16. Fourier transform infrared imaging of Cotton trash mixtures

    Science.gov (United States)

    There is much interest in the identification of trash types comingled with cotton lint. A good understanding of the specific trash types present can lead to the fabrication of new equipment which can identify and sort cotton trash found with cotton fiber. Conventional methods, including the High Vo...

  17. Changes in cotton gin energy consumption apportioned by ten functions

    Science.gov (United States)

    The public is concerned about air quality and sustainability. Cotton producers, gin owners and plant managers are concerned about rising energy prices. Both have an interest in cotton gin energy consumption trends. Changes in cotton gins’ energy consumption over the past fifty years, a period of ...

  18. The Cost of Ginning Cotton - 2007 Survey Results

    Science.gov (United States)

    The 2007 United States cotton crop was 18.7 million running bales, 11 percent below 2006 production. This crop was gathered from 10.2 million acres, which yielded a record high 879 pounds per acre and was ginned with 806 operating gins, averaging over 23,000 bales per gin. There has been a yearly ...

  19. Economics of oversized cyclones in the cotton ginning industry

    Science.gov (United States)

    Cost of reducing pollution to meet increasingly stringent air quality standards particularly for the U.S. cotton ginning industry is rising overtime. Most industry participants use cyclones to control air pollutants. These cyclones have no moving parts and their initial investment costs are relative...

  20. Bioinspiration and Biomimicry: Possibilities for Cotton Byproducts

    Science.gov (United States)

    The byproducts from cotton gins have commonly been referred to as cotton gin trash or cotton gin waste primarily because the lint and seed were the main focus of the operation and the byproducts were a financial liability that did not have a consistent market. Even though the byproducts were called ...

  1. 3rd stage seed-cotton cleaning system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  2. 2nd stage seed-cotton cleaning system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  3. 1st stage seed-cotton cleaning system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  4. Overflow system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  5. 1st stage mote system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts to characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was f...

  6. 2nd stage lint cleaning system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  7. 1st stage lint cleaning system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  8. Mote cleaner system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  9. Combined mote system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  10. Mote cyclone robber system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  11. Unloading system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  12. Combined lint cleaning system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  13. Cyclone robber system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  14. 2nd stage mote system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  15. Battery condenser system total particulate emission factors and rates for cotton gins: Method 17

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  16. Battery condenser system PM10 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that to characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study ...

  17. Battery condenser system total particulate emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study was...

  18. Botanical trash mixtures analyzed with near-infrared and attenuated total reflectance fourier transform spectroscopy and thermogravimetric analysis

    Science.gov (United States)

    Botanical cotton trash mixed with lint reduces cotton’s marketability and appearance. During cotton harvesting, ginning, and processing, trash size reduction occurs, thus complicating its removal and identification. This trash causes problems by increasing ends down in yarn formation and thus proce...

  19. Characterization of cotton gin PM10 emissions based on EPA stack sampling methodologies and particle size distributions

    Science.gov (United States)

    A project to characterize cotton gin emissions in terms of stack sampling was conducted during the 2008 through 2011 ginning seasons. The impetus behind the project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. EPA AP-42 emission factors ar...

  20. Theoretical bases of rotation dynamics of raw materials poller with s ratify consideration for saw gin processing of cotton

    International Nuclear Information System (INIS)

    Saidov, Kh.; Babaeva, A.Kh.

    2005-01-01

    In this paper is examined motion of raw materials rollers on the base of a stratify models. Foe every layers of the rollers are determined dynamical influences for saw gin processing of cotton. It is noticed that in the gin processing of cotton the second layer of cotton roller plagues an important role

  1. Work health and safety in cotton ginning industry: a survey of practices in australia

    International Nuclear Information System (INIS)

    Soomro, N.

    2015-01-01

    This survey focuses on the WH and S (Work Health and Safety) practices in Australia and relates them with those in Pakistan. It also highlights the planned areas of work required on WH and S in cotton ginning industry of Pakistan. This article is one a series of research studies that will inform a broader approach development. The aim of the survey was to design a standardized health and safety Act for cotton ginning industry of Pakistan and to help ginners meet their due industry obligations under the model WH and S Act. The first component of the research study survey was to review the relevant Australian work and safety model as this provides a framework to protect the health, safety and welfare of all employees at work and of other people who might be affected by the job. The second aspect of the research study survey concerned site visits to cotton gins with the support of Australian Centre for Agricultural Health and Safety, Moree, NSW. During these visits the existing ginning process in terms of WH and S were reviewed. Informal interviews were also conducted with Gin Managers and Ginning Experts regarding WH and S in the Australian cotton ginning industry. (author)

  2. Battery condenser system PM10 emission factors and rates for cotton gins: Method 201A PM10 sizing cyclones

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that to characterize cotton gin emissions from the standpoint of stack sampling. The impetus behind this project was the urgent need to collect additional cotton gin emissions data to address current regulatory issues. A key component of this study ...

  3. Development of cotton gin PM10 emission factors for EPA’s AP-42

    Science.gov (United States)

    The Compilation of Air Pollution Emission Factors (AP-42) emission factors are assigned ratings, from A (Excellent) to E (Poor), based on the quality of data used to develop them. All current PM10 cotton gin emission factors received quality ratings of D or lower. In an effort to improve these ratin...

  4. Update on the development of cotton gin PM10 emission factors for EPA's AP-42

    Science.gov (United States)

    A cotton ginning industry-supported project was initiated in 2008 to update the U.S. Environmental Protection Agency’s (EPA) Compilation of Air Pollution Emission Factors (AP-42) to include PM10 emission factors. This study develops emission factors from the PM10 emission factor data collected from ...

  5. Battery condenser system particulate emission factors for cotton gins: Particle size distribution characteristics

    Science.gov (United States)

    This report is part of a project to characterize cotton gin emissions from the standpoint of total particulate stack sampling and particle size analyses. In 2013, the Environmental Protection Agency (EPA) published a more stringent standard for particulate matter with nominal diameter less than or e...

  6. Battery condenser system PM2.5 emission factors and rates for cotton gins

    Science.gov (United States)

    This manuscript is part of a series of manuscripts that detail a project to characterize cotton gin emissions from the standpoint of stack and ambient sampling. The impetus behind the project was the 2006 EPA implementation of a more stringent standard for particulate matter less than or equal to 2....

  7. 100 Years of Cotton Production, Harvesting and Ginning Systems Engineering: 1907 - 2007

    Science.gov (United States)

    The American Society of Agricultural and Biological Engineers (ASABE) celebrated its centennial year during 2007. As part of the ASABE centennial, the authors were asked to describe agricultural engineering accomplishments in U.S. cotton production, harvesting and ginning over the past 100 years. ...

  8. Ginning U.S. cotton for domestic and export markets

    Science.gov (United States)

    The U.S. cotton crop is produced by a highly mechanized production system that seeks to minimize manual labor while maximizing fiber quality. It is estimated that a bale of U.S. cotton is produced using approximately three man hours of labor while foreign producers may utilize several hundred man h...

  9. CATEGORIZATION OF EXTRANEOUS MATTER IN COTTON USING MACHINE VISION SYSTEMS

    Science.gov (United States)

    The Cotton Trash Identification System (CTIS) was developed at the Southwestern Cotton Ginning Research Laboratory to identify and categorize extraneous matter in cotton. The CTIS bark/grass categorization was evaluated with USDA-Agricultural Marketing Service (AMS) extraneous matter calls assigned ...

  10. Development of cotton gin PM10 emission factors for EPA’s AP-42-DUPLICATE DO NOT USE

    Science.gov (United States)

    The Compilation of Air Pollution Emission Factors (AP-42) emission factors are assigned ratings, from A (Excellent) to E (Poor), based on the quality of data used to develop them. All current PM10 cotton gin emission factors received quality ratings of D or lower. In an effort to improve these ratin...

  11. A simulated approach to estimating PM10 and PM2.5 concentrations downwind from cotton gins

    Science.gov (United States)

    Cotton gins are required to obtain operating permits from state air pollution regulatory agencies (SAPRA), which regulate the amount of particulate matter that can be emitted. Industrial Source Complex Short Term version 3 (ISCST3) is the Gaussian dispersion model currently used by some SAPRAs to pr...

  12. A review of the effects of ginning practices on cotton fibre and yarn properties and processing performance

    CSIR Research Space (South Africa)

    Sanderson, KW

    1985-08-01

    Full Text Available Over the years, since the first formal cotton ginning experiments were conducted by the United State department of agriculture in 1962, a large volume of literature, from research papers to popular articles, has been published on the effect...

  13. Relationship between three cotton trash measurements: High Volume Instrumentation (HVI), Shirley Analyzer (SA), and Advanced Fiber Information System (AFIS)

    Science.gov (United States)

    Presence of non-lint materials (trashes) in commercial cotton bales at various amounts degrades the market values and further influences the end-use qualities. In order to ensure a fair trading, the USDA’s AMS has introduced the high volume instrument (HVI) measurement as a universal standard index....

  14. Laboratory microwave measurement of the moisture content in seed cotton and ginned cotton fiber

    Science.gov (United States)

    The timely and accurate measurement of cotton fiber moisture content is important, but the measurement is often performed by laborious, time-consuming laboratory oven drying methods. Microwave technology for measuring fiber moisture content directly (not for drying only) offers potential advantages...

  15. Impacto do beneficiamento sobre o número de neps e quantidade de impurezas da fibra do algodão Ginning impact on the number of neps and amount of cotton fiber contaminants

    Directory of Open Access Journals (Sweden)

    Odilon R. R. F. da Silva

    2010-01-01

    lint with 350 g were collected to be analyzed by the AFIS instrument (Advanced Fiber Information System, for determining the content of trash, dust and the number of neps in the cotton fiber. The results indicate that the processes of cotton pre-cleaning and fiber cleaning reduced significantly the amount of cotton trash and dust, while that jointly with the ginning, these processes increased the number of neps in cotton fiber. The use of the saw lint cleaner system increases the efficiency of fiber cleaning, but causes considerable rise in the number of neps.

  16. Parallel Algorithm for GPU Processing; for use in High Speed Machine Vision Sensing of Cotton Lint Trash

    Directory of Open Access Journals (Sweden)

    Mathew G. Pelletier

    2008-02-01

    Full Text Available One of the main hurdles standing in the way of optimal cleaning of cotton lint isthe lack of sensing systems that can react fast enough to provide the control system withreal-time information as to the level of trash contamination of the cotton lint. This researchexamines the use of programmable graphic processing units (GPU as an alternative to thePC’s traditional use of the central processing unit (CPU. The use of the GPU, as analternative computation platform, allowed for the machine vision system to gain asignificant improvement in processing time. By improving the processing time, thisresearch seeks to address the lack of availability of rapid trash sensing systems and thusalleviate a situation in which the current systems view the cotton lint either well before, orafter, the cotton is cleaned. This extended lag/lead time that is currently imposed on thecotton trash cleaning control systems, is what is responsible for system operators utilizing avery large dead-band safety buffer in order to ensure that the cotton lint is not undercleaned.Unfortunately, the utilization of a large dead-band buffer results in the majority ofthe cotton lint being over-cleaned which in turn causes lint fiber-damage as well assignificant losses of the valuable lint due to the excessive use of cleaning machinery. Thisresearch estimates that upwards of a 30% reduction in lint loss could be gained through theuse of a tightly coupled trash sensor to the cleaning machinery control systems. Thisresearch seeks to improve processing times through the development of a new algorithm forcotton trash sensing that allows for implementation on a highly parallel architecture.Additionally, by moving the new parallel algorithm onto an alternative computing platform,the graphic processing unit “GPU”, for processing of the cotton trash images, a speed up ofover 6.5 times, over optimized code running on the PC’s central processing

  17. Modelling and Predicting the Breaking Strength and Mass Irregularity of Cotton Rotor-Spun Yarns Containing Cotton Fiber Recovered from Ginning Process by Using Artificial Neural Network Algorithm

    Directory of Open Access Journals (Sweden)

    Mohsen Shanbeh

    2011-01-01

    Full Text Available One of the main methods to reduce the production costs is waste recycling which is the most important challenge for the future. Cotton wastes collected from ginning process have desirable properties which could be used during spinning process. The purpose of this study was to develop predictive models of breaking strength and mass irregularity (CV% of cotton waste rotor-spun yarns containing cotton waste collected from ginning process by using the artificial neural network trained with backpropagation algorithm. Artificial neural network models have been developed based on rotor diameter, rotor speed, navel type, opener roller speed, ginning waste proportion and yarn linear density as input parameters. The parameters of artificial neural network model, namely, learning, and momentum rate, number of hidden layers and number of hidden processing elements (neurons were optimized to get the best predictive models. The findings showed that the breaking strength and mass irregularity of rotor spun yarns could be predicted satisfactorily by artificial neural network. The maximum error in predicting the breaking strength and mass irregularity of testing data was 8.34% and 6.65%, respectively.

  18. Battery condenser system PM2.5 emission factors and rates for cotton gins: Method 201A combination PM10 and PM2.5 sizing cyclones

    Science.gov (United States)

    This report is part of a project to characterize cotton gin emissions from the standpoint of stack sampling. In 2006, EPA finalized and published a more stringent standard for particulate matter with nominal diameter less than or equal to 2.5 µm (PM2.5). This created an urgent need to collect additi...

  19. Development of a prototype sensor to detect plastic contamination in seed cotton at the gin

    Science.gov (United States)

    US cotton is considered to have some of the lowest levels of contamination in the world. That reputation is expected by foreign and domestic mills. Despite this reputation, U.S. spinners have recently experienced some serious contamination issues with US cotton. Of particular concern are plastic con...

  20. Cultured Trash, Not Trash Culture

    Directory of Open Access Journals (Sweden)

    Taufiqurrohman Taufiqurrohman

    2017-09-01

    Full Text Available As civilized creature, human actually can manage trash as well as possible although it is often stereotyped as a vain thing. This article gives the proof that trash can be cultured as well so that a society can take benefits from the existence of it. This article parses ways of orderly managing it at schools, in this case two schools in Jepara. The results say that trash can be cultured by having an organization to manage the Trash Bank at schools and to train students to classify and recycle trash then take advantage of it by selling the collected and the recycled trash. It makes trash have good transformation of values, repelling against the prior stereotype. Finally, by taking example from Trash Bank management at schools, human can have so cultured trash that they would not be trapped by trash culture.

  1. How Much Trash Do You Trash?

    Science.gov (United States)

    Nargund-Joshi, Vanashri; Lee, Jean S.

    2013-01-01

    A classroom discussion started after a student noticed three days of accumulated trash in the wastebasket and exclaimed, "Wow, look at the trash! If it keeps piling up like this, it will soon be everywhere!" His statement motivated the authors' class to research about the trash, or solid waste, we create and what can we do about it.…

  2. trash epoch

    Directory of Open Access Journals (Sweden)

    Elena Grigoryeva

    2012-02-01

    Full Text Available Unconventionally, the editorial of this issue begins with two epigraphs:trash1. foolish ideas or talk; nonsense;2. Chiefly US and Canadian useless or unwanted matter or objects;3. a literary or artistic production of poor quality;4. Chiefly US and Canadian a poor or worthless person or a group of such people.[Collins English Dictionary]You got to make good out of bad. That's all there is to make it with. Robert Penn Warren, “All the King’s Men”.But before talking about the topic of the issue, we should pay off the debt. The previous (double issue was completely devoted to Irkutsk’s jubilee. We will fill in the gaps and look back on the events of the past year missed by PB. There are a lot of them: the UIA Congress in Tokyo (5-7, the Zodchestvo Festival and the UAR Plenary Meeting in Moscow (16-29, the review competition of graduation works in Erevan (30–39 and Les Ateliers of Urban Planning and Development in Cergy-Pontoise (48–54.The New Year’s news blends into the topic of the issue. This year in Irkutsk discarded Christmas trees began to be recycled into fertilizer. In the Kemerovo region the old Christmas trees are used as food for cows. So the supercilious attitude toward trash is no longer relevant. In the future we shall eat it; actually, we are already eating it. Artists help us adjust to the idea that we will live in the global dump. Trash Muses inspired Zhenya Kraineva and Konstantin Lidin to a diptych about trash art (66–75.The first essential step in waste recycling is to change our view on waste. In people’s minds the dump is turned into a deposit of valuable resources. The detailed text by Andrei Ivanov (90–99 tells us about a slum district obtaining a new status and turning into a historical heritage.It is very urgent to convert trash into resources. On the Earth, mountains of garbage grow twice as fast as the population. 17% of homes in Sweden are heated with garbage

  3. Hearing impairment among workers exposed to excessive levels of noise in ginning industries

    Directory of Open Access Journals (Sweden)

    Kamalesh J Dube

    2011-01-01

    Full Text Available Cotton ginning workers have a risk of hearing loss due to excessive noise levels at the workplace environment. In this study, estimates of typical sound levels prevailing at the workplace environment and its effects on hearing ability of the exposed workers were made among cotton ginning workers. Data on self-reported health status was collected by a questionnaire survey at 10 cotton ginning industries located at Jalgaon district of Maharashtra state, India. The cotton ginning workers were exposed to continuous noise levels between 89 and 106 dBA. The hearing ability of the subjects was accessed by pure tone audiometry. The results of audiometry show mild, moderate and moderately severe degree of hearing impairment among the cotton ginning workers. The data generated during the study show that hearing loss was significantly associated with period of exposure to the workplace noise (P <0.0001. The prevalence of audiometric hearing impairment defined as a threshold average greater than 25 dB hearing level was 96% for binaural low-frequency average, 97% for binaural mid frequency average and 94% for binaural high-frequency average in the cotton ginning workers. We recommend the compulsory use of personal protective equipment like ear plug by the cotton ginning workers at the workplace environment. A regular maintenance of ginning and pressing machineries will avoid the emission of excessive noise at the workplace environment of cotton gins. A regular periodic medical examination is necessary to measure the impact of workplace noise on the health of cotton ginning workers.

  4. Desenvolvimento e avaliação de um descaroçador e prensa enfardadeira itinerantes para o beneficiamento do algodão Development of a mobile gin and baler press for cotton

    Directory of Open Access Journals (Sweden)

    Jeane F. Jerônimo

    2013-03-01

    Full Text Available Novas tecnologias vêm sendo incorporadas ao sistema produtivo da cotonicultura brasileira, visando verticalizar a produção por meio do beneficiamento do algodão em caroço possibilitando, aos produtores ou associações, a agregação de valor à sua produção. Objetivou-se então, com o presente trabalho, desenvolver e avaliar um equipamento de beneficiamento composto de descaroçador e prensa enfardadeira itinerantes. O descaroçador se compõe de: limpador, cilindro de serras, cilindro de escovas, condensador e rolo. A prensa enfardadeira é constituída de chapas de prensagem, cilindros hidráulicos, bomba hidráulica, válvula de controle de acionamento, dispositivos de filtragem do óleo hidráulico e manômetro. Esses equipamentos são montados sobre um reboque composto por chassi de cantoneiras em U, quatro rodas de aro 13, pontas de eixo, dois feixes de cinco molas, lastro em chapa de ferro e sistema de frenagem. Na avaliação e validação do conjunto pelos cotonicultores, este conjunto recebeu o conceito "muito bom" quanto ao rendimento do descaroçador, o peso do fardo e em relação à qualidade da fibra obtida. A qualidade da fibra obtida com o conjunto descaroçador e prensa enfardadeira atendeu aos padrões da indústria têxtil.New technologies have been incorporated into the Brazilian cotton production system, in order to verticalize the production through processing, allowing the producers or associations to add value to their production. Thus, the present study aimed to develop and evaluate processing equipment composed of mobile gin and baler press. The ginner consists of cleaner, saw cylinder, cylinder brushes, condenser and coil. The baler press is constituted of pressing sheets, hydraulic cylinders, hydraulic pump, control valve actuation, devices for filtering hydraulic oil and manometer. These devices are mounted on a trailer chassis composed of U-shaped angle iron chassis, four wheels (rim 13, shaft ends, two

  5. Absolute moisture sensing for cotton bales

    Science.gov (United States)

    With the recent prevalence of moisture restoration systems in cotton gins, more and more gins are putting moisture back into the bales immediately before the packaging operation. There are two main reasons for this recent trend, the first is that it has been found that added moisture at the bale pre...

  6. EVALUATION OF GIN WASTE AS A GROWING SUBSTRATE, ENRICHED WITH DIFFERENT VOLUME PERCENTAGE OF THE WHEAT BRAN FOR CULTIVATION OF OYSTER MUSHROOM (PLEUROTUS OSTREATUS

    Directory of Open Access Journals (Sweden)

    M. M. Akhtar

    2016-08-01

    Full Text Available Pleurotusostreatus mushroom was cultivated on cotton gin waste amended with wheat bran in order to judge its growth potential. Two substrates (cotton gin waste and wheat bran were employed alone and with different combinations. Experiment consisted of four treatments T0 (100 % cotton gin waste, T1(97% cotton gin waste + 3% wheat bran, T2(94% cotton gin waste + 6% wheat bran and T3(91% cotton gin waste + 9% wheat bran. Data about time needed for commencement of spawn run, time needed for completion of mycelial growth, time needed for initiation of pinheads, time needed for harvesting of 1st, 2nd and 3rd flush, fresh weight of 1st, 2nd and 3rd flush harvested, total yield, pH of mushroom, total soluble solids of mushroom, acidity and ascorbic acid contents, reducing sugars, non-reducing sugars and total sugars of mushroom, total nitrogen, phosphorus and potassium contents of mushroom was recorded. T0 (100 % cotton gin waste performed better as compared to other treatments.

  7. Trash-to-Gas: Converting Space Trash into Useful Products

    Science.gov (United States)

    Caraccio, Anne J.; Hintze, Paul E.

    2013-01-01

    NASA's Logistical Reduction and Repurposing (LRR) project is a collaborative effort in which NASA is determined to reduce total logistical mass through reduction, reuse and recycling of various wastes and components of long duration space missions and habitats. LRR is focusing on four distinct advanced areas of study: Advanced Clothing System, Logistics-to-Living, Heat Melt Compactor and Trash to Supply Gas (TtSG). The objective of TtSG is to develop technologies that convert material waste, human waste and food waste into high-value products. High-value products include life support oxygen and water, rocket fuels, raw material production feedstocks, and other energy sources. There are multiple pathways for converting waste to products involving single or multi-step processes. This paper discusses thermal oxidation methods of converting waste to methane. Different wastes, including food, food packaging, Maximum Absorbent Garments (MAGs), human waste simulants, and cotton washcloths have been evaluated in a thermal degradation reactor under conditions promoting pyrolysis, gasification or incineration. The goal was to evaluate the degradation processes at varying temperatures and ramp cycles and to maximize production of desirable products and minimize high molecular weight hydrocarbon (tar) production. Catalytic cracking was also evaluated to minimize tar production. The quantities of CO2, CO, CH4, and H2O were measured under the different thermal degradation conditions. The conversion efficiencies of these products were used to determine the best methods for producing desired products.

  8. Use of Electronic Technologies to Manage Seed Cotton Modules

    Science.gov (United States)

    Most U.S. farmers and ginners still use paper tags to identify cotton modules along with a large number painted on the side of traditional modules. The gin typically assigns tags for the modules. When the gin gets the module, the paper tag is removed and the information is manually entered into a s...

  9. Trust It or Trash It?

    Science.gov (United States)

    Trust It or Trash It? About | Contact | Español Tab 1 Tab 2 What is Trust It or Trash It? This is a tool ... be true, it may be. (See the second “Trust it” statement above). Click on each element below ...

  10. 29 CFR 780.806 - Exempt ginning limited to first processing.

    Science.gov (United States)

    2010-07-01

    ... cottonseed, is not exempt under section 13(b)(15). It is not first processing of the seed cotton; rather, it... 29 Labor 3 2010-07-01 2010-07-01 false Exempt ginning limited to first processing. 780.806 Section... AGRICULTURE, PROCESSING OF AGRICULTURAL COMMODITIES, AND RELATED SUBJECTS UNDER THE FAIR LABOR STANDARDS ACT...

  11. Engineering economic evaluations of trash segregation alternatives

    International Nuclear Information System (INIS)

    Collins, H.E.

    1987-01-01

    Health physicists are becoming increasingly involved in the selection of equipment to segregate a contaminated trash from clean trash in the effort to reduce low level waste disposal costs. Although well qualified to evaluate the technical merits of different equipment, health physicists also need to be aware of the elements of economic comparisons of different alternatives that meet all technical requirements

  12. Preliminary evidence of oxidation in standard oven drying of cotton: attenuated total reflectance/ Fourier transform spectroscopy, colorimetry, and particulate matter formation

    Science.gov (United States)

    Moisture is paramount to cotton fiber properties dictating harvesting, ginning, storage and spinning as well as others. Currently, oven drying in air is often utilized to generate the percentage of moisture in cotton fibers. Karl Fischer Titration another method for cotton moisture, has been compa...

  13. Hydrodynamics induced vibration to trash-racks

    International Nuclear Information System (INIS)

    Sadrnejad, A.

    2002-01-01

    In conventional power plants trash-racks are provided at the intakes to protect the turbines. In pumped storage plants, the draft tube or tailrace must also have trash-racks to protect the units while pumping. Because the loads believed to cause many failures of trash-racks are dynamic in nature, it is important to understand the dynamic characteristics of trash-racks structures in general and a single rack in particular. The classical added-mass solution structure-fluid dynamic interaction is known as an approximate solution procedure. An accurate added-mass approach mixed with implementation in finite element framework is proposed. In this proposal, experimental conclusions, supported by theory, led to presentation of more accurate results in vibration of trash-racks. This numerical solution as a powerful method to solve such a complex problem can be employed to carry out dynamic characteristics of these structures while vibrating in water

  14. Composting of cotton wastes; Compostaje de residuos de algodon

    Energy Technology Data Exchange (ETDEWEB)

    Dobao, M.M.; Tejada, M.; Benitez, C.; Gonzalez, J.L.

    1997-12-31

    In this article a study on the composting process of residuals of cotton gin is presented crushed and not crushed, previous. The analysis of correlation gotten for each one of the treatments reveals that although common correlations between the parameters studied for both treatment exist, they are presented a great number of correlations between this parameters for the treatment of cotton crushed residuals. (Author) 11 refs.

  15. MOISTURE IN COTTON BY THE KARL FISCHER TITRATION REFERENCE METHOD

    Science.gov (United States)

    Moisture is a critical parameter that influences many aspects of cotton fiber from harvesting and ginning to various fiber properties. Because of their importance, reference moisture methods that are more accurate than the existing oven-drying techniques and relatively easy to generate results are ...

  16. Using digital images to measure and discriminate small particles in cotton

    Science.gov (United States)

    Taylor, Robert A.; Godbey, Luther C.

    1991-02-01

    Inages from conventional video systems are being digitized in coraputers for the analysis of small trash particles in cotton. The method has been developed to automate particle counting and area measurements for bales of cotton prepared for market. Because the video output is linearly proportional to the amount of light reflected the best spectral band for optimum particle discrimination should be centered at the wavelength of maximum difference between particles and their surroundings. However due to the spectral distribution of the illumination energy and the detector sensitivity peak image performance bands were altered. Reflectance from seven mechanically cleaned cotton lint samples and trash removed were examined for spectral contrast in the wavelength range of camera sensitivity. Pixel intensity histograms from the video systent are reported for simulated trashmeter area reference samples (painted dots on panels) and for cotton containing trash to demonstrate the particle discrimination mechanism. 2.

  17. Long-term performance of thermoplastic composite material with cotton burr and stem (CBS) as a partial filler

    Science.gov (United States)

    Rationale: Cotton burr and stem (CBS) fraction of cotton gin byproducts has shown promise as a fiber filler in thermoplastic composites, with physical and mechanical properties comparable to that made with wood fiber fillers. However, the long-term performance of this composite material is not known...

  18. Genetic diversity in upland cotton for cotton leaf curl virus disease, earliness and fiber quality

    International Nuclear Information System (INIS)

    Saeed, F.; Farooq, J.; Mahmood, A.; Hussain, T.

    2014-01-01

    In Pakistan during last two decades the major factor limiting cotton production is cotton leaf curl virus disease (CLCuD). For estimation of genetic diversity regarding CLCuD tolerance, fiber quality and some yield contributing traits, 101 cotton genotypes imported from USA were evaluated. Different statistical procedures like cluster, principle components (PC) and correlation analysis were employed to identify the suitable genotypes that can be further exploited in breeding programme. Significant associations were found between yield contributing trait, boll weight and fiber related trait, staple length. Earliness related traits, like days taken to 1 square and days taken to 1 flower had positive correlation with each other and both these traits also showed their positive association with ginning out turn. The negative significant correlation of CLCuD was obtained with monopodial branches, sympodial branches and plant height. Principal component (PC) analysis showed first five PCs having eigen value >1 explaining 67.8% of the total variation with days to st 1 square and flowering along with plant height and sympodia plant which were being the most important characters in PC1. Cluster analysis classified 101 accessions into five divergent groups. The genotypes in st cluster 1 only showed reasonable values for days to 1 square and flower, sympodia per plant, ginning out turn, staple length and fiber fineness and the genotypes in cluster 5 showed promising values for the traits like cotton leaf curl virus, ginning out turn and fiber fineness. The genotypes in cluster 1 and 5 may be combined to obtain desirable traits related to earliness and better disease tolerance. Scatter plot and tree diagrams demonstrated sufficient diversity among the cotton accessions for various traits and some extent of association between various clusters. It is concluded that diversity among the genotypes could be utilized for the development of CLCuD resistant lines with increased seed

  19. Trash Talking and Good Times on the Softball Field

    Science.gov (United States)

    Aicinena, Steven

    2008-01-01

    Trash talking can be found in virtually all American sport environments. It is viewed by many as a tool to achieve athletic success. Trash talking can be a harmless form of verbal jousting. However, there comes a point at which trash talking serves as motivation for violence inside of the sport setting and outside of it as well. In this paper, the…

  20. Of volcanoes, saints, trash, and frogs

    DEFF Research Database (Denmark)

    Andersen, Astrid Oberborbeck

    , at the same time as political elections and economic hardship. During one year of ethnographic fieldwork volcanoes, saints, trash and frogs were among the nonhuman entities referred to in conversations and engaged with when responding to the changes that trouble the world and everyday life of Arequipans...

  1. Trash and Aesthetics in the Hoard

    Directory of Open Access Journals (Sweden)

    Charmaine Eddy

    2015-06-01

    Full Text Available Trash and Aesthetics in the Hoard by Charmaine Eddy, Issue 7: The Aesthetics of Trash. This article examines two reality television series, Hoarders and Hoarding: Buried Alive, in terms of a variation in the understanding of the object in relation to value based upon an aesthetic tied to consumer capitalism. Object collection is viewed as a spectacle of abjection in each episode, as items that were once worthy of purchase come to produce a garbage heap within the home. The concept of “trash” is an evaluative category applied to objects over time, but it also becomes part of the therapeutic process, as hoarders are required to dispose of their things. Object-oriented ontology, or “thing theory,” provides an alternate semiology for the object, ultimately illustrating how an evaluative aesthetics of the object in these series is linked to consumer capitalism and normative patterns of consumption.

  2. From Trash to Treasure: Recycling Scrap Metal into Steel

    Science.gov (United States)

    Cantu, Diana

    2011-01-01

    Trash is having a global impact not only on land, but at sea--making its way into the ocean and creating large islands of floating debris. One such island is The Great Pacific Trash Patch, which is located in the North Pacific and is made up of floating trash and debris that is spread out in an area as much as one and a half times the size of the…

  3. Trash-polluted irrigation: characteristics and impact on agriculture

    Science.gov (United States)

    Sulaeman, D.; Arif, SS; Sudarmadji

    2018-04-01

    Trash pollution has been a problem in sustainable water resources management. Trash pollutes not only rivers, lakes and seas, but also irrigation canals and rice fields. This study aimed to identify the characteristics of solid waste (type, time of occurrence and sources of trash) and its impact on agriculture. The study was conducted in four irrigation areas, namely Gamping, Merdiko, Nglaren and Karangploso in Bantul District, Yogyakarta Special Region. We applied the Irrigation Rapid Trash Assessment (IRTA) as our field survey instrument. The results showed that trash was found throughout irrigation canals and rice fields, and the occurrence was influenced by water flow, time and farmer activities. The irrigation was dominantly polluted by plastic trash (52.2%), biodegradable waste (17.91%) and miscellaneous trash (12.3%). The IRTA score showed that Gamping Irrigation Area was at marginal condition, bearing a high risk of disturbing the operation and maintenance of the irrigation canals as well as farmers’ health. Trash in irrigation also generated technical impact of the irrigation operation and maintenance, environmental quality, and social life. This research also offered environmental policy integration approach and water-garbage governance approach as an alternative solution to manage water resources and agriculture in a sustainable manner, under the pressure of increasing amount of trash.

  4. Basura electrónica Electronic trash

    OpenAIRE

    Pedro Costa Morata

    2012-01-01

    Este texto es un comentario acerca del vídeo viral "Buy it, Use it, Break it, Junk it, it's Toxic" de la organización Greenpeace sobre el problema presentado por la “basura electrónica”, una amenaza ambiental relativamente reciente derivado del ingente consumo de aparatos electrónicos.This text is a comment about the viral video "Buy it, Use it, Break it, Junk it, it's Toxic", from Greenpeace, about the problem presented by the "electronic trash", a relatively recently environmental threat de...

  5. Solar Powered Reverse Trash Vendo Machine

    Directory of Open Access Journals (Sweden)

    Alexis John M. Rubio

    2016-05-01

    Full Text Available –The study was conducted with the purpose of developing a Solar Powered Reverse Trash Vendo Machine that aims to encourage people to engage in recycling and to diminish the practice of improper waste disposal in thePhilippines. The device used a Gizduino X ATMega 1281 as its main processing module along with a Gizduino 644 microcontroller board, anda GSM Shield module for communication. Arduino1.6 IDE is used to program the Gizduinoboards. The device is powered by a 15V rechargeable battery, which is charged by a solar panel retrofitted at the roof of the device, this is to promote energy conservation, and green engineering principles in the development of the study.The device can process empty plastic bottles (500ml. max with a base diameter of 3.5 inches, and aluminium cans. These recyclable materials are placed inside the machine and is scanned, then crushed and placed in a bin. An inductive sensor is used to detect either the material is a plastic bottle or an aluminium can. To compensate the user for recycling, an equivalent monetary value will be dispensed. The owner of the device can check the status of the coin dispenser and bins through an Android messaging application developed using the Eclipse IDE and the Java programming language, and when a certain limit is reached by the coin dispenser or the trash bins, an automatic text message notification will be sent to the owner.

  6. Pleurotus sajor caju

    African Journals Online (AJOL)

    Administrator

    The influence of fungus treatment on the biochemical composition and degradation patter of sawdust and cotton plant by-products (cotton burns and cotton gin trash) by Pleurotus sajor caju were evaluated. Lignin degradation increased as the incubation period progressed while the highest loss of hemicellulose, cellulose ...

  7. Batch biomethanation of banana trash and coir path

    Energy Technology Data Exchange (ETDEWEB)

    Deivanai, K.; Bai, R.K. [Madurai Kamaraj Univ. (India)

    1995-08-01

    Anaerobic digestion of banana trash and coir pith was carried out for a period of one month by batch digestion. During biomethanation reduction of total- and volatile-solids was, respectively, 25.3 and 39.6% in banana trash and 13.6 and 21.6% in coir pith. A production of 9.22 l and 1.69 l (per kg TS added) of biogas with average methane content of 72 and 80% was achieved from banana trash and coir pith, respectively. (author)

  8. Cotton contamination

    CSIR Research Space (South Africa)

    Van der Sluijs, MHJ

    2018-05-01

    Full Text Available This review focusses on physical forms of contaminant including the presence, prevention and/or removal of foreign bodies, stickiness and seed-coat fragments rather than the type and quantity of chemical residues that might be present in cotton...

  9. Characterization of Volume F Trash from the Three FY11 STS Missions: Trash Weights and Categorization and Microbial Characterization

    Science.gov (United States)

    Strayer, Richard F.; Hummerick, Mary E.; Richards, Jeffrey T.; McCoy, LaShelle E.; Roberts, Michael S.; Wheller, Raymond M.

    2011-01-01

    The project reported here provides microbial characterization support to the Waste Management Systems (WMS) element of NASA's Life Support and Habitation Systems (LSHS) program. Conventional microbiological methods were used to detect and enumerate microorganisms in STS Volume F Compartment trash for three shuttle missions: STS 133, 134, and 135. This trash was usually made available within 2 days of landing at KSC. The Volume F bag was weighed, opened and the contents were cataloged and placed into categories: personal hygiene items - inclUding EVA maximum absorbent garments (MAGs) and Elbow packs (daily toilet wipes, etc), drink containers, food waste (and containers), office waste (paper), and packaging materials - plastic film and duct tape. The average wet trash generation rate for the three STS missions was 0.362 % 0.157 kgwet crew 1 d-1 . This was considerably lower and more variable than the average rate for 4 STS missions reported for FY10. Trash subtotals by category: personal hygiene wastes, 56%; drink items, 11 %; food wastes, 18%; office waste, 3%; and plastic film, 12%. These wastes have an abundance of easily biodegraded compounds that can support the growth of microorganisms. Microbial characterization of trash showed that large numbers of bacteria and fungi have taken advantage of this readily available nutrient source to proliferate. Exterior and interior surfaces of plastic film bags containing trash were sampled and counts of cultivatable microbes were generally low and mostly occurred on trash bundles within the exterior trash bags. Personal hygiene wastes, drink containers, and food wastes and packaging all contained high levels of, mostly, aerobic heterotrophic bacteria and lower levels of yeasts and molds. Isolates from plate count media were obtained and identified .and were mostly aerobic heterotrophs with some facultative anaerobes. These are usually considered common environmental isolates on Earth. However, several pathogens were also

  10. Modernity rejected? Marketing schnapps gin in West Africa, 1945 ...

    African Journals Online (AJOL)

    During the 1950s and 1960s, advertising for a diverse range of products, ... why African consumers rejected the claim that schnapps gin was „modern‟, and why ... used and interpreted on a day-to-day level during the decolonisation era. ... on marketing and consumption of imported commodities in twentieth-century Africa.

  11. Influence of Trash-Barriering on Operation of Pumping Station with Wet-Pits

    Directory of Open Access Journals (Sweden)

    Baoyun Qiu

    2014-04-01

    Full Text Available Trash racks are set before inlet sumps of a pumping station with wet-pits in order to block trash. The flow fields before and behind the trash rack were numerically simulated and flow fields in the inlet sump were calculated using the simulated velocity distribution of the section behind the trash rack as the inlet boundary condition. Local head loss of trash-barriering increases with the increase of blockage ratio of the trash rack. When waterweeds block upper part of the trash rack, flow pattern behind the trash rack will be extremely turbulent, flow velocity of lower part of inlet section of inlet sump will increase, flow velocity of the upper part will decrease, and even backflow appears, which will deteriorate the flow pattern and increase head loss in the inlet sump. Trash-barriering has little effect on velocity distribution of impeller inlet section. Trash-barriering will not only increase head and power of the pump but also decrease the flow. For the example of the pumping station: when blockage ratios of the trash racks are 0.3, 0.5, and 0.7, operating cost will increase by 13%~43% than that of without trash racks. Therefore, the trash rack should be cleaned up timely.

  12. American Material Culture: Investigating a World War II Trash Dump

    Energy Technology Data Exchange (ETDEWEB)

    Julie Braun

    2005-10-01

    The Idaho National Laboratory: An Historical Trash Trove Historians and archaeologists love trash, the older the better. Sometimes these researchers find their passion in unexpected places. In this presentation, the treasures found in a large historic dump that lies relatively untouched in the middle of the Idaho National Laboratory (INL) will be described. The U.S. military used the central portion of the INL as one of only six naval proving grounds during World War II. They dumped trash in dry irrigation canals during and after their wartime activities and shortly before the federal government designated this arid and desolate place as the nation’s nuclear reactor testing station in 1949. When read critically and combined with memories and photographs, the 60-year old trash provides a glimpse into 1940s’ culture and the everyday lives of ordinary people who lived and worked during this time on Idaho’s desert. Thanks to priceless stories, hours of research, and the ability to read the language of historic artifacts, the dump was turned from just another trash heap into a treasure trove of 1940s memorabilia. Such studies of American material culture serve to fire our imaginations, enrich our understanding of past practices, and humanize history. Historical archaeology provides opportunities to integrate inanimate objects with animated narrative and, the more recent the artifacts, the more human the stories they can tell.

  13. DETERMINATION THE EFFECT OF DEFOLIATION TIMING ON COTTON YIELD AND QUALITY

    Directory of Open Access Journals (Sweden)

    Karademir Emine

    2007-12-01

    Full Text Available This study was carried out for determining the effect of different application times at 40, 50, 60 and 70 % boll opening and untreated plot of the defoliant on cotton yield, earliness and technological properties in Southeast Anatolia Region conditions in Turkey. Maras 92 cotton variety was used as plant material in the experiment field of the Southeast Anatolia Agricultural Research Institute during 2000-2001. Defoliant was including thidiazuron + diuron chemical substance. The result of this study showed that ginning percentage, 100 seed weight, seed germination percentage, fiber fineness, fiber length, fiber strength, reflectance, elongation and seed cotton yield were not affected by the treatment; plant height and first picking percentage in 2001, fiber uniformity in 2000 were 5 % significantly affected. This study showed that application of defoliant didn’t affect significantly yield and technological properties of cotton and after 40 % boll opening the defoliant can be used.

  14. Trash to Supply Gas (TtSG) Project Overview

    Science.gov (United States)

    Hintze, Paul; Santiago-Maldonado, Edgardo; Kulis, Michael J.; Lytle, John K.; Fisher, John W.; Vaccaro, Helen; Ewert, Michael K.; Broyan, James L.

    2012-01-01

    Technologies that reduce logistical needs are a key to long term space missions. Currently, trash and waste generated during a mission is carried during the entire roundtrip mission or stored inside a logistic module which is de-orbited into Earth's atmosphere for destruction. The goal of the Trash to Supply Gas (TtSG) project is to develop space technology alternatives for converting trash and other waste materials from human spaceflight into high-value products that might include propellants or power system fuels in addition to life support oxygen and water. In addition to producing a useful product from waste, TtSG will decrease the volume needed to store waste on long term space missions. This paper presents an overview of the TtSG technologies and future plans for the project.

  15. Alternative Fuels Data Center: Central Ohio Turns Trash Into Natural Gas

    Science.gov (United States)

    Central Ohio Turns Trash Into Natural Gas to someone by E-mail Share Alternative Fuels Data Center : Central Ohio Turns Trash Into Natural Gas on Facebook Tweet about Alternative Fuels Data Center: Central Ohio Turns Trash Into Natural Gas on Twitter Bookmark Alternative Fuels Data Center: Central Ohio Turns

  16. An OmpA Family Protein, a Target of the GinI/GinR Quorum-Sensing System in Gluconacetobacter intermedius, Controls Acetic Acid Fermentation▿ †

    Science.gov (United States)

    Iida, Aya; Ohnishi, Yasuo; Horinouchi, Sueharu

    2008-01-01

    Via N-acylhomoserine lactones, the GinI/GinR quorum-sensing system in Gluconacetobacter intermedius NCI1051, a gram-negative acetic acid bacterium, represses acetic acid and gluconic acid fermentation. Two-dimensional polyacrylamide gel electrophoretic analysis of protein profiles of strain NCI1051 and ginI and ginR mutants identified a protein that was produced in response to the GinI/GinR regulatory system. Cloning and nucleotide sequencing of the gene encoding this protein revealed that it encoded an OmpA family protein, named GmpA. gmpA was a member of the gene cluster containing three adjacent homologous genes, gmpA to gmpC, the organization of which appeared to be unique to vinegar producers, including “Gluconacetobacter polyoxogenes.” In addition, GmpA was unique among the OmpA family proteins in that its N-terminal membrane domain forming eight antiparallel transmembrane β-strands contained an extra sequence in one of the surface-exposed loops. Transcriptional analysis showed that only gmpA of the three adjacent gmp genes was activated by the GinI/GinR quorum-sensing system. However, gmpA was not controlled directly by GinR but was controlled by an 89-amino-acid protein, GinA, a target of this quorum-sensing system. A gmpA mutant grew more rapidly in the presence of 2% (vol/vol) ethanol and accumulated acetic acid and gluconic acid in greater final yields than strain NCI1051. Thus, GmpA plays a role in repressing oxidative fermentation, including acetic acid fermentation, which is unique to acetic acid bacteria and allows ATP synthesis via ethanol oxidation. Consistent with the involvement of gmpA in oxidative fermentation, its transcription was also enhanced by ethanol and acetic acid. PMID:18487322

  17. An OmpA family protein, a target of the GinI/GinR quorum-sensing system in Gluconacetobacter intermedius, controls acetic acid fermentation.

    Science.gov (United States)

    Iida, Aya; Ohnishi, Yasuo; Horinouchi, Sueharu

    2008-07-01

    Via N-acylhomoserine lactones, the GinI/GinR quorum-sensing system in Gluconacetobacter intermedius NCI1051, a gram-negative acetic acid bacterium, represses acetic acid and gluconic acid fermentation. Two-dimensional polyacrylamide gel electrophoretic analysis of protein profiles of strain NCI1051 and ginI and ginR mutants identified a protein that was produced in response to the GinI/GinR regulatory system. Cloning and nucleotide sequencing of the gene encoding this protein revealed that it encoded an OmpA family protein, named GmpA. gmpA was a member of the gene cluster containing three adjacent homologous genes, gmpA to gmpC, the organization of which appeared to be unique to vinegar producers, including "Gluconacetobacter polyoxogenes." In addition, GmpA was unique among the OmpA family proteins in that its N-terminal membrane domain forming eight antiparallel transmembrane beta-strands contained an extra sequence in one of the surface-exposed loops. Transcriptional analysis showed that only gmpA of the three adjacent gmp genes was activated by the GinI/GinR quorum-sensing system. However, gmpA was not controlled directly by GinR but was controlled by an 89-amino-acid protein, GinA, a target of this quorum-sensing system. A gmpA mutant grew more rapidly in the presence of 2% (vol/vol) ethanol and accumulated acetic acid and gluconic acid in greater final yields than strain NCI1051. Thus, GmpA plays a role in repressing oxidative fermentation, including acetic acid fermentation, which is unique to acetic acid bacteria and allows ATP synthesis via ethanol oxidation. Consistent with the involvement of gmpA in oxidative fermentation, its transcription was also enhanced by ethanol and acetic acid.

  18. Experiences developing socially acceptable interactions for a robotic trash barrel

    DEFF Research Database (Denmark)

    Yang, Stephen; Mok, Brian Ka Jun; Sirkin, David

    2015-01-01

    strategies that seemed to evoke clear engagement and responses, both positive and negative. Observations and interviews show that a) people most welcome the robot's presence when they need its services and it actively advertises its intent through movement; b) people create mental models of the trash barrel...

  19. 29 CFR 1928.57 - Guarding of farm field equipment, farmstead equipment, and cotton gins.

    Science.gov (United States)

    2010-07-01

    .... Functional components, such as snapping or husking rolls, straw spreaders and choppers, cutterbars, flail.... Panels made of materials conforming to the requirements in Table D-1, or equivalent, may be substituted... Guard Panel Materials Material Clearance from moving part at all points (in inches) Largest mesh or...

  20. Head losses in small hydropower plant trash racks (SHP

    Directory of Open Access Journals (Sweden)

    N. Walczak

    2016-12-01

    Full Text Available Small hydropower plants (SHP are technical facilities that are part of alternative energy sources [Paish 2002]. They are primarily characterised by low unit power (in Poland below 5 MW and are often constructed on existing barrages. Electrical current produced by these plants is used to meet local demand. Considering the exploitation of SHPs, it is important to ensure a stable flow through turbines. Aggidis et al. [2010] analysed SHP equipment costs depending on the turbine set. The turbines are protected against damage with trash racks applied for capturing water-borne detritus, such as plant debris carried by water. However, trash racks as solid equipment of SHPs cause head losses, and as a consequence reduce the efficiency of the system. These losses result not only from the spacing of bars, their shape and the technical condition of the inlet chamber, but also from plant debris, its nature, and the quantity of accumulated material that effectively limits the flow. The plant debris captured on trash racks is characterised by diversity in terms of species composition related to the vegetation period and the area where hydraulic facilities are located. Therefore, it is important to maintain trash racks clean by regular removal of the accumulated material. In this context, modernised and newly built power plants are fitted with mechanical cleaners. In older facilities, manual intervention for regular cleaning is required. The present study analyses how the bar shape and the orientation angle of trash racks as well as the accumulated plant debris affect head losses. The results were obtained from laboratory tests. The research examined the impact the inclination angle of trash racks (30°, 60° and 80° has on head loss values for three different shapes of bars (cylindrical, angled and flat rectangular and various weight portions of plant debris (0.25, 0.375 and 0.5 kg. The summarised losses were determined by measuring the difference in water

  1. Dictionary of Cotton

    Science.gov (United States)

    The Dictionary of Cotton has over 2,000 terms and definitions that were compiled by 33 researchers. It reflects the ongoing commitment of the International Cotton Advisory Committee, through its Technical Information Section, to the spread of knowledge about cotton to all those who have an interest ...

  2. Trash can bomb can fall into the hands of terrorists

    CERN Multimedia

    2001-01-01

    Leading scientists from CERN described how if terrorists were able to get their hands on plutonium or uranium, they would be able to manufacture a 'trash can' nuclear bomb simply by inserting the radioactive material into a normal bomb. Once detonated a large area could be contaminated leading to the immediate deaths of many with many more future casualties due to cancers caused by the radiation.

  3. STUDY & SURVEY ON TRASH BIN USING WI-FI TECHNOLOGY

    OpenAIRE

    Yash Kumar Gadwal*, Siddharth Kumar Gupta, VedikaTiwari, Yash Raj Rao, Vedant Bakliwal

    2016-01-01

    India is a country where people love to break the rules, We see it on the roads where no one is driving in their lane. We see it in the way people disrespect public spaces by throwing garbage anywhere that they want to.So the people from THINKSCREAM came up with this idea and invented a trash can that rewards people with 15 minutes of free Wi-Fi every time they throw something away.

  4. Trash to Gas: Converting Space Waste into Useful Supply Products

    Science.gov (United States)

    Tsoras, Alexandra

    2013-01-01

    The cost of sending mass into space with current propulsion technology is very expensive, making every item a crucial element of the space mission. It is essential that all materials be used to their fullest potential. Items like food, packaging, clothing, paper towels, gloves, etc., normally become trash and take up space after use. These waste materials are currently either burned up upon reentry in earth's atmosphere or sent on cargo return vehicles back to earth: a very wasteful method. The purpose of this project was to utilize these materials and create useful products like water and methane gas, which is used for rocket fuel, to further supply a deep space mission. The system used was a thermal degradation reactor with the configuration of a down-draft gasifier. The reactor was loaded with approximately 100g of trash simulant and heated with two external ceramic heaters with separate temperature control in order to create pyrolysis and gasification in one zone and incineration iri a second zone simultaneously. Trash was loaded into the top half of the reactor to undergo pyrolysis while the downdraft gas experienced gasification or incineration to treat tars and maximize the production of carbon dioxide. Minor products included carbon monoxide, methane, and other hydrocarbons. The carbon dioxide produced can be sent to a Sabatier reactor to convert the gas into methane, which can be used as rocket propellant. In order to maximize the carbon dioxide and useful gases produced, and minimize the unwanted tars and leftover ashen material, multiple experiments were performed with altered parameters such as differing temperatures, flow rates, and location of inlet air flow. According to the data received from these experiments, the process will be further scaled up and optimized to ultimately create a system that reduces trash buildup while at the same time providing enough useful gases to potentially fill a methane tank that could fuel a lunar ascent vehicle or

  5. Identification of cotton properties to improve yarn count quality by using regression analysis

    International Nuclear Information System (INIS)

    Amin, M.; Ullah, M.; Akbar, A.

    2014-01-01

    Identification of raw material characteristics towards yarn count variation was studied by using statistical techniques. Regression analysis is used to meet the objective. Stepwise regression is used for mode) selection, and coefficient of determination and mean squared error (MSE) criteria are used to identify the contributing factors of cotton properties for yam count. Statistical assumptions of normality, autocorrelation and multicollinearity are evaluated by using probability plot, Durbin Watson test, variance inflation factor (VIF), and then model fitting is carried out. It is found that, invisible (INV), nepness (Nep), grayness (RD), cotton trash (TR) and uniformity index (VI) are the main contributing cotton properties for yarn count variation. The results are also verified by Pareto chart. (author)

  6. Influence of bleach activators on the fabric made from cotton (gossypium hamster l.)

    International Nuclear Information System (INIS)

    Asif, H.M.; Iftikhar, M.; Shahbaz, B.

    2013-01-01

    Raw cotton contains various type of trash and most of the impurities are removed during the spinning process but still the cotton fabric coming from the weaving or knitting process always contains some impurities. Some time cotton fabric gets the oil, stains and coloured materials which affect the quality of dyed fabric. Bleaching is a process that eliminates unwanted coloured matters from the fibres, yarn and fabrics. A bleaching agent is a material that lightens or whitens a substrate through chemical action. Hydrogen peroxide is by far the most commonly used oxidative bleaching agent for cotton and its blends, accounting for more than 90 percent of all the bleaching agents. The use of activators to enhance the bleaching performance of hydrogen peroxide for cellulosic materials has gained popularity now a day. In this context the main objectives of this paper are to study the influence of different bleaching activators on cotton fabric and to give implications for textile extension.The results indicate that the activators with different concentrations, along with different concentrations of hydrogen peroxide (H/sub 2/O/sub 2) have significant influence on the bleaching performance of cotton fabric. (author)

  7. 25 CFR 171.420 - Can I dispose of sewage, trash, or other refuse on a BIA irrigation project?

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Can I dispose of sewage, trash, or other refuse on a BIA... AND WATER IRRIGATION OPERATION AND MAINTENANCE Irrigation Facilities § 171.420 Can I dispose of sewage, trash, or other refuse on a BIA irrigation project? No. Sewage, trash, or other refuse are considered...

  8. Trash to Gas (TtG) Simulant Analysis

    Science.gov (United States)

    Miles, John D., II; Hintze, Paul E.

    2014-01-01

    Space exploration in outer earths orbit is a long-term commitment, where the reuse of discarded materials is a critical component for its success. The Logistics Reduction and Repurposing (LRR) project under the NASA Advanced Exploration System Program is a project focused on technologies that reduce the amount of consumables that are needed to be sent into space, repurpose items sent to space, or convert wastes to commodities. In particular, Trash to Gas (TtG), part of the LRR project, is a novel space technology capable of converting raw elements from combustible waste including food waste and packaging, paper, wipes and towels, nitrile gloves, fecal matter, urine brine, maximum absorbency garments, and other organic wastes from human space exploration into useful gases. Trash to gas will ultimately reduce mission cost by producing a portion of important consumables in situ. This paper will discuss results of waste processing by steam reforming. Steam reforming is a thermochemical process developed as part of TtG, where waste is heated in the presence of oxygen and steam to produce carbon dioxide, carbon monoxide, hydrogen, methane and water. The aim of this experiment is to investigate the processing of different waste simulants and their gaseous products. This will lay a foundation for understating and optimizing the production of useful gases for propulsion and recovery of water for life support.

  9. Superoleophobic cotton textiles

    NARCIS (Netherlands)

    Leng, B.; Shao, Z.; With, de G.; Ming, W.

    2009-01-01

    Common cotton textiles are hydrophilic and oleophilic in nature. Superhydrophobic cotton textiles have the potential to be used as self-cleaning fabrics, but they typically are not super oil-repellent. Poor oil repellency may easily compromise the self-cleaning property of these fabrics. Here, we

  10. Cotton trends in India

    Indian Academy of Sciences (India)

    First page Back Continue Last page Graphics. Cotton trends in India. A crop of significant economic importance, valued at over Rs. 15000 Crs. Provides income to 60 million people. Crucial raw material for Rs 83000 Crores textile industry out of which Rs 45754 crores is exports. Approx. 20 Million acres of cotton provides ...

  11. The "Cotton Problem"

    OpenAIRE

    Baffes, John

    2005-01-01

    Cotton is an important cash crop in many developing economies, supporting the livelihoods of millions of poor households. In some countries it contributes as much as 40 percent of merchandise exports and more than 5 percent of gross domestic product (GDP). The global cotton market, however, has been subject to numerous policy interventions, to the detriment of nonsubsidized producers. This ...

  12. PELOLOSAN IKAN KURISI (Nemipterus japonicus MELALUI JUVENILE AND TRASH EXLUDER DEVICES PADA JARING ARAD

    Directory of Open Access Journals (Sweden)

    Hufiadi Hufiadi

    2016-06-01

    Full Text Available Permasalahan utama pada perikanan jaring arad adalah banyaknya jumlah hasil tangkap sampingan berukuran kecil yang belum layak tangkap. Dalam upaya untuk mengurangi tangkapan ikan muda yang belum layak tangkap telah dilakukan observasi dan ujicoba operasi penangkapan melalui penggunaan perangkat juvenile and trash exluder devices pada alat tangkap jaring arad yang dioperasikan nelayan di Pekalongan. Perangkat juvenile and trash exluder devices yang digunakan dibedakan pada ukuran jarak antar kisi, yaitu 10,0; 17,5; dan 25,4 mm. Analisis selektivitas kisi menggunakan model kurva logistik dengan bantuan solver pada Microsoft Excel. Hasil penelitian menunjukkan bahwa penggunaan juvenile and trash exluder devices pada jaring arad dapat meloloskan ikan kurisi (Nemipterus spp. berukuran kecil. Ukuran jarak antar kisi 25,4 mm mempunyai selektivitas yang paling baik terhadap ikan kurisi berdasarkan atas ukuran panjang baku dan jarak antar kisi 17,5 mm mempunyai selektivitas paling baik berdasarkan atas ukuran lingkar tubuh ikan kurisi.   The serius problem on bottom mini trawl has the large number caught of bycatch caught especially for juvenile and trash fish. Improvement to reduce catches of juvenile was conducted through observation and experimental fishing using juvenile and trash exluder devices of mini bottom trawl in Pekalongan. The juvenile and trash excluder devices (juvenile and trash exluder devices in the experimental fishing with different space bar of the juvenile and trash exluder devices i.e. 10.0; 17.5; and 25.4 mm. The selectivity analysis of logistic curve by using solver on Microsoft Excel was applied. The results showed that juvenile and trash excluder devices might reduce catches of threadfin breams juvenile. Where as 25.4 space bar had the best selectivity based on the size of threadfin breams fork length and 17.5 mm space bar had the best selectivity based on the size of threadfin breams body girth.

  13. Characterization of Volume F Trash from Four Recent STS Missions: Weights, Categorization, Water Content

    Science.gov (United States)

    Strayer, Richard F.; Hummerick, Mary E.; Richards, Jeffrey T.; McCoy, LaShelle E.; Roberts, Michael S.; Wheeler, Raymond M.

    2011-01-01

    The fate of space-generated solid wastes, including trash, for future missions is under consideration by NASA. Several potential treatment options are under consideration and active technology development. Potential fates for space-generated solid wastes are: Storage without treatment; storage after treatment(s) including volume reduction, water recovery, sterilization, and recovery plus recycling of waste materials. Recycling might be important for partial or full closure scenarios because of the prohibitive costs associated with resupply of consumable materials. For this study, we determined the composition of trash returned from four recent STS missions. The trash material was 'Volume F' trash and other trash, in large zip-lock bags, that accompanied the Volume F trash. This is the first of two submitted papers on these wastes. This one will cover trash content, weight and water content. The other will report on the microbial Characterization of this trash. STS trash was usually made available within 2 days of landing at KSC. The Volume F bag was weighed, opened and the contents were catalogued and placed into one of the following categories: food waste (and containers), drink containers, personal hygiene items - including EVA maximum absorbent garments (MAGs)and Elbow packs (daily toilet wipes, etc), paper, and packaging materials - plastic firm and duct tape. Trash generation rates for the four STS missions: Total wet trash was 0.602 plus or minus 0.089 kg(sub wet) crew(sup -1) d(sup -1) containing about 25% water at 0.154 plus or minus 0.030 kg(sub water) crew(sup -1) d(sup -1) (avg plus or minus stdev). Cataloguing by category: personal hygiene wastes accounted for 50% of the total trash and 69% of the total water for the four missions; drink items were 16% of total weight and 16% water; food wastes were 22% of total weight and 15% of the water; office waste and plastic film were 2% and 11% of the total waste and did not contain any water. The results can be

  14. Commander Lousma is surrounded by a week's worth of trash on the middeck

    Science.gov (United States)

    1982-01-01

    Commander Lousma, wearing communication kit assembly (ASSY) mini headset (HDST), gathers three freefloating plastic trash bags filled with empty containers, paper towels, straws, etc. Lousma will stow them in a designated stowage volume.

  15. Utilisation of sugarcane trash and other cellulosic wastes for production of oxalic acid

    Energy Technology Data Exchange (ETDEWEB)

    Mane, J D; Modak, H M; Ramaiah, N A; Jadhav, S J

    1988-01-01

    The nitric acid oxidation process was developed for the production of oxalic acid from sugarcane trash, groundnut shells, corn cobs and rice husks. Good yields of oxalic acid from the above raw materials were obtained under optimum conditions, with sugarcane trash as the preferable raw material. The absorption of waste nitrogen oxide gases in aqueous NaOH to get a valuable by-product, sodium nitrite, was also successful.

  16. Case Study of Trash Fish under Environmental Stress for Their Survival and Utilization

    OpenAIRE

    Tehseen Ahmed; Imran Malik; Qazi Jahnzeb; Khalid Ahmed; Rafia Azmat

    2008-01-01

    The intention of this study was to describe nutritional status of a low value/trash fish which have a low commercial value by virtue of their low consumer preference, low quality and small size. This research provided the important information about the hazards of environments on low valued fish and discussed survival of trash fish with the importance and significance of minerals and nutrition like sodium, potassium, calcium, moisture, total protein, total fat, ash and calorific value w...

  17. Application of Optimum Compaction Energy in the Development of Bricks Made with Construction Trash Soils

    OpenAIRE

    Lopez-Lara, T.; Gonzalez-Vega, C. L.; Hernandez-Zaragoza, J. B.; Rojas-Gonzalez, E.; Carreón-Freyre, D.; Salgado-Delgado, R.; Garcia-Hernandez, E.; Cerca, M.

    2014-01-01

    In general, bricks frequently show different densities and therefore different resistances because the compaction energy is not considered in their production. Expansive soils represent a problem for light buildings over them because of volumetric instability. A generalized solution has been to extract them and substitute them by inert soil; thus they become construction trash. So, in this work the compaction energy aspect and the use of construction trash soils in the elaboration of resistan...

  18. Trash Can Volcano - One Change of State with Endless Possibilities

    Science.gov (United States)

    Brill, K. A.; Lanza, F.; Gochis, E. E.; Lechner, H. N.; Waite, G. P.

    2013-12-01

    Introducing students to earth science and geophysical concepts in fun, innovative and demonstrative ways is critical to capturing the attention of students at all levels. A properly designed experiment may provide a variety of dimensions that middle and high school teachers can use to introduce some of the core ideas in geosciences while addressing many of the Next Generation Science Standards (NGSS). Using a modified experiment from Harpp et al. (2005) referred to here as 'Trash Can Volcano' we introduce students to the fields of volcanology, natural hazards, and geophysics as well as the use of models and data analysis in an inquiry based fashion. The Trash Can Volcano uses the expansive properties of boiling nitrogen or subliming carbon dioxide to simulate an eruption of a magmatic system. We produce an analog model of an eruption by confining either of these gasses in a submerged plastic soda pop bottle. The expanding gasses pressurize the bottle beyond the yield strength of the plastic; the resulting explosion is analogous to a Strombolian style eruption. An experiment of this type engages students by providing a dramatic experience and begs further inquiry into the nature of the event. This activity also provides educators with a variety of possible directions to explore the core ideas and NGSS standards. In one of our explorations we show how scientists monitor volcanic eruptions and hazards. We deploy three separate microphones to capture atmospheric pressure changes at known distances, and students can calculate the speed of the wave emitted from the energetic release of the gas by identifying the arrival of the waves at each microphone. Using this data, students can also investigate wave attenuation. In another module, students observe the demonstration, develop a research plan, discuss different variables and controls, and then observe the explosive demonstration again. This methodology provides an opportunity to observe, learn and study an event

  19. GINS complex protein Sld5 recruits SIK1 to activate MCM helicase during DNA replication.

    Science.gov (United States)

    Joshi, Kiranmai; Shah, Varun Jayeshkumar; Maddika, Subbareddy

    2016-12-01

    In eukaryotes, proper loading and activation of MCM helicase at chromosomal origins plays a central role in DNA replication. Activation of MCM helicase requires its association with CDC45-GINS complex, but the mechanism of how this complex activates MCM helicase is poorly understood. Here we identified SIK1 (salt-inducible kinase 1), an AMPK related protein kinase, as a molecular link that connects GINS complex with MCM helicase activity. We demonstrated that Sld5 a component of GINS complex interacts with SIK1 and recruits it to the sites of DNA replication at the onset of S phase. Depletion of SIK1 leads to defective DNA replication. Further, we showed that SIK1 phosphorylates MCM2 at five conserved residues at its N-terminus, which is essential for the activation of MCM helicase. Collectively, our results suggest SIK1 as a novel integral component of CMG replicative helicase during eukaryotic DNA replication. Copyright © 2016 Elsevier Inc. All rights reserved.

  20. Estimation of Heterosis and Combining Ability in F1 Hybrids of Upland Cotton for Yield and Fiber Traits

    International Nuclear Information System (INIS)

    Arain, B.T.; Baloch, M.J.; Bughio, Q.U.A.; Sial, P.; Arain, M.A.; Baloch, A.

    2015-01-01

    The experimental research was conducted so as to determine the general combining ability (GCA) and specific combining ability (SCA) estimates and heterotic effects for seed cotton yield and fibre traits in 5 x 5 half diallel crosses of upland cotton (Gossypium hirsutum L.). The parental genotypes studied were; CRIS-134, IR-3701, IR-1524, FH-113 and MG-6. The characters such as bolls/plant, sympodial branches/plant, boll weight (g), plant height (cm), fibre length (mm), seed cotton yield/plant (g), seed index (g) and ginning out turn percentage were studied. The experiment was laid-out in a randomized complete block design with four replications at experimental field of the Department of Plant Breeding and Genetics, Sindh Agriculture University Tandojam, Pakistan during 2013. The results revealed that, parents and hybrids differed significantly for their mean performance regarding all the traits studied. The importance of heterotic effects was evident from the significance of parents vs. hybrids performance. The variances due to GCA and SCA were significant for all the traits except that GCA was non-significant for boll weight only whereas, SCA was non-significant for boll weight, seed index and ginning out turn percentage. The significance of GCA indicated the importance of additive genes advocating the traits while, the involvement of non-additive genes was evident from the significance of SCA variances. The GCA variances were greater than SCA for bolls per plant, plant height, seed cotton yield and lint percentage while, SCA variances were higher than GCA for sympodial branches/plant and fibre length. Parents IR-3701, FH-113 and MG-6 displayed higher positive GCA effects for bolls/plant, sympodial branches/plant, fibre length, seed cotton yield, seed index and ginning out turn percentage. The per se performance of these three parents was exactly reflected in their GCA effects and such happenings are exceptional. Such results suggested that, all three parents were

  1. Effect of cotton leaf-curl virus on the yield-components and fibre properties of cotton genotypes under varying plant spacing and nitrogen fertilizer

    International Nuclear Information System (INIS)

    Ahmad, S.; Hayat, K.; Ashraf, F.; Sadiq, M.A.

    2008-01-01

    Cotton leaf-curl virus (CLCu VB. Wala strain) is one of the major biotic constraints of cotton production in Punjab. Development of resistant cotton genotype is the most feasible, economical and effective method to combat this hazardous problem, but so far no resistant genotype has been reported. Therefore, the objective of this study was to compare yield and yield-components and fiber traits of different genotypes/varieties under different plant spacing and nitrogen fertilizer as a management strategy to cope with this viral disease. Field experiment was conducted during 2006-07 to evaluate the effect of genotype, plant spacing and nitrogen fertilizer on cotton. Five genotypes (MNH-786, MNH-789, MNH- 6070, CIM- 496, and BH-160), three plant-spacings (15, 30 and 45 cm) and three nitrogen fertilizer-levels (6.5, 8.6 and 11 bags Urea / ha) were studied. Results showed that significant differences exist for plant height, no. of bolls/m/sup -2/, seed-cotton yield (kg/ha) due to genotype, interaction of genotype with plant spacing and nitrogen fertilizer level. Whereas boll weight, ginning out-turn, staple length and fiber fineness were not affected significantly by the plant spacing and nitrogen fertilizer, the effect due to genotype was significant for these traits. CLCuV infestation varied significantly with genotypes, while all other factors, i.e., plant spacing and nitrogen fertilizers, have non-significant effect. As the major objective of cotton cultivation is production of lint for the country and seed- cotton yield for the farmers, it is noted that genotypes grown in narrow plant-spacing (15 cm) and higher nitrogen fertilizer level (11.0 bags of urea/ha) produced maximum seed-cotton yield under higher CLCu V infestation in case of CIM-496, MNH-789 and BH-I60, while the new strain MNH-6070 gave maximum yield under 30cm plant-spacing and 8.6 bags of urea/ha has the 2.3% CLCu V infestation was observed in this variety. From the present study, it is concluded that

  2. Ginásio Clube Português (GCP) : measuring customer satisfaction in services industry

    OpenAIRE

    Alves, Guilherme Fernandes Rito

    2015-01-01

    The objective of this thesis is to measure and analyze the customer satisfaction level in Ginásio Clube Português, by understanding the key determinants and consequences of customer satisfaction. After an exponential growth both in revenues and in number of clients between 1998 and 2011, Ginásio Clube Português is losing competitive edge due to the increasing competition in the high-end and low-cost markets as well as due to the effects of the economic downturn. Aiming to en...

  3. Cotton (Gossypium hirsutum L.).

    Science.gov (United States)

    Rathore, Keerti S; Campbell, LeAnne M; Sherwood, Shanna; Nunes, Eugenia

    2015-01-01

    Cotton continues to be a crop of great economic importance in many developing and some developed countries. Cotton plants expressing the Bt gene to deter some of the major pests have been enthusiastically and widely accepted by the farmers in three of the major producing countries, i.e., China, India, and the USA. Considering the constraints related to its production and the wide variety of products derived from the cotton plant, it offers several target traits that can be improved through genetic engineering. Thus, there is a great need to accelerate the application of biotechnological tools for cotton improvement. This requires a simple, yet robust gene delivery/transformant recovery system. Recently, a protocol, involving large-scale, mechanical isolation of embryonic axes from germinating cottonseeds followed by direct transformation of the meristematic cells has been developed by an industrial laboratory. However, complexity of the mechanical device and the patent restrictions are likely to keep this method out of reach of most academic laboratories. In this chapter, we describe the method developed in our laboratory that has undergone further refinements and involves Agrobacterium-mediated transformation of cotton cells, selection of stable transgenic callus lines, and recovery of plants via somatic embryogenesis.

  4. Characteristics and properties of sugar cane trash; Caracteristicas e propriedades do palhico de cana-de-acucar

    Energy Technology Data Exchange (ETDEWEB)

    Innocente, Andreia F. [Universidade Estadual Paulista (UNESP), Botucatu, SP (Brazil); Saglietti, Jose R. C. [Universidade Estadual Paulista (IBB/UNESP), Botucatu, SP (Brazil). Inst. de Biociencias de Botucatu], E-mail: jroberto@ibb.unesp.br

    2010-07-01

    The sugar cane processing wastes (bagasse and trash) became an important energy source which may be used in the electrical energy co-generation. This work is aimed to determine the trash physical properties, define its energetic value and ideal combination of bagasse + trash to use in conventional boilers. The trash productivity (20 t/ha), green (14.9%) and dry (71.3%) leaves, and remaining material (8.3%) was found one day after the cane crop. The trash moisture content was measured for each component and the final average value was 28.7%. The bagasse showed a 49.81% moisture average content. The higher heating value (HHV) was found for the bagasse (19.27 MJ/kg), trash (17.90 MJ/kg) and bagasse + trash mixtures in different proportions. For the lower heating value (LHV), we observed that the released energy in the trash (12.11 MJ/kg) was higher than the one in the bagasse (8.55 MJ/kg). This result was expected due to the higher bagasse moisture content. From the analysed mixtures, the 50%-50% one had the highest LHV (10.08 MJ/kg), showing that the trash left in the field after the crop may be efficient for the energy production mixed to the bagasse in 50% proportion. (author)

  5. A microcultura de um ginásio de treinamento de ginástica artística feminina de alto rendimento

    OpenAIRE

    Mauricio dos Santos de Oliveira

    2014-01-01

    No esporte podemos identificar microculturas constituídas por um grupo de pessoas que compartilham valores, crenças, padrões de comportamentos e um sistema de símbolos, verbal e não verbal, que os distingue do meio cultural dominante. O ginásio é o espaço no qual as microculturas de Ginástica Artística (GA) estão resguardadas e mantém a preeminência das tradições que constituem, em âmbito maior, a macrocultura da modalidade. Nesse ambiente há uma teia de significados, supostamente compartilha...

  6. Environmental Assessment of the City of El Cerrito, CA: Creek, Trash and Air Quality Analysis

    Science.gov (United States)

    Moore, A.; Ilan, A.

    2015-12-01

    The City of El Cerrito, CA is located within Western Contra Costa County and adjacent to the San Francisco Bay. Local land-uses that affect its overall public and environmental health include major freeways, railways, and commercial and industrial zones. In an effort to assess the overall health of the local environment, students at Korematsu Middle School conducted a comprehensive analysis that included street litter auditing, water monitoring of Cerritos Creek and air quality measurements made along local streets. In 2014 the City of El Cerrito adopted a long-term trash plan that included strategies for reducing trash loads of local stormwater sewer systems. This plan called for load reduction of 70% by July 1, 2017 and 100% by July 1, 2022. To evaluate the effectiveness of the trash plan, our team quantified and scored trash concentration levels at two locations—one in a residential neighborhood and the other in a commercial zone. We also monitored water quality at nearby Cerritos Creek to investigate the impacts that each area's trash concentrations had on water quality. We also monitored particulate matter (PM) concentration levels in air within these locations to determine whether or not differences exist between residential and commercial areas. Preliminary analysis of litter data suggests that the Long Term Trash Plan has thus far been effective in reducing concentrations of street litter along San Pablo Avenue, which is located within a major commercial zone, but has been inadequate in reducing trash in nearby parks. Water quality results indicate that Cerritos Creek contains waters that are quite healthy with respect to Ammonia and Nitrate concentration levels (i.e., very low values for every sample collected). However, elevated concentration levels of Phosphates were detected in every sample collected. Air quality data surprisingly revealed that extremely high PM concentration levels occur in air surrounding a residential park in El Cerrito.

  7. Genotype-by-sowing date interaction effects on cotton yield and quality in irrigated condition of dera ismail khan, pakistan

    International Nuclear Information System (INIS)

    Usman, K.; Khan, S.; Ayatullah, A.

    2016-01-01

    Cotton is a major export commodity of Pakistan. It is affected by variable environmental conditions throughout the country which limits its production. A 2-year field study was conducted in 2012 and 2013 at Cotton Research Station, Dera Ismail Khan, Pakistan to evaluate the effects of six sowing dates on yield and quality attributes of four cotton genotypes. The experiments were laid out in split-plot within a randomized complete block design with three replications. Main plots treatments were six sowing dates, namely March 20, April 4, April 19, May 4, May 19, and June 3 while subplots treatments were four approved transgenic varieties of cotton (CIM-598, CIM-599, CIM-602, and Ali Akber-703). Results revealed that earlier planting produced more vegetative growth rather than lint yield while late planting induced flowering and boll formation when temperature was much cold that adversely affected cotton yield and quality. The results further indicate that the genotype CIM-599 scored first rank in number of bolls plant-1, boll weight, seed cotton yield, ginning out turn, fiber length, fiber strength, fiber fineness, and fiber uniformity when sown on April 19. CIM-598 was the next suitable genotype after CIM-599 which produced higher yield and quality traits in April 19 sowing. Earlier and later sowing than April 19 resulted in lower cotton yield and quality characters due to unfavorable environmental conditions and shorter growth period, respectively. Thus it is concluded that the genotype, CIM-599 sown on April 19 suits well to the study area and had the potential to optimize cotton yield and quality in irrigated condition of Dera Ismail Khan, Pakistan. (author)

  8. Análise de seis sistemas de recolhimento do palhiço na colheita mecânica da cana-de-açúcar Analysis of six systems of trash recovery in mechanical harvesting of sugarcane

    Directory of Open Access Journals (Sweden)

    Marcio B. Michelazzo

    2008-10-01

    Full Text Available A biomassa da cana-de-açúcar é uma das fontes de energia renovável mais disponível no Brasil, em virtude dos seus resíduos de colheita, como palhiço (pontas e folhas; todavia, o aproveitamento do palhiço em larga escala é dificultado pelo alto custo de sua recuperação, sobretudo no que diz respeito ao recolhimento, adensamento e transporte. Com o presente trabalho, apresenta-se uma análise dos processos envolvidos na recuperação do palhiço, como densidade final do palhiço e princípios operacionais das máquinas envolvidas, juntamente com uma análise econômica, através de um modelo de cálculo de custo, por meio de simulação de rendimentos e capacidades operacionais que compõem cada sistema de recuperação do palhiço. Seis sistemas foram avaliados, técnica e economicamente. De acordo com os resultados, o sistema de colheita integral apresentou o menor custo de recuperação do palhiço para qualquer distância, seguido dos sistemas picado a granel, fardo cilíndrico, fardo algodoeiro, peletização e briquetagem.Sugarcane biomass is one of the energy sources most readily available in Brazil, mainly due to residues such as trash (tops, dry and green leaves. Large scale use of these residues still faces high recovery costs related to gathering, baling, transportation, chopping and residue utilization technology. An analysis was done of the mechanical principles involved in the packing processes. A model was defined to estimate the cost of trash recovery, simulating the field capacity, oil consumption, depreciation, repair and maintenance as well as labor required for the field and transport operations. Six recovery systems were studied both from the technical and economical points of view. The results showed that handling billets and trash together, described as "Integral harvesting", has the lowest cost for trash recovery, both for short and long distances, followed by bulk handling of chopped trash, the round bale, the

  9. Characterization of Escherichia coli populations from gulls, landfill trash, and wastewater using ribotyping.

    Science.gov (United States)

    Nelson, M; Jones, S H; Edwards, C; Ellis, J C

    2008-08-19

    Due to their opportunistic and gregarious nature, gulls may be important reservoirs and vectors for anthropogenically derived fecal pathogens in coastal areas. We used ribotyping, a genotypic bacterial source tracking method, to compare populations of Escherichia coli among herring gulls Larus argentatus, great black-backed gulls L. marinus, wastewater, and landfill trash in New Hampshire and Maine, USA. Concentrations of E. coli in gull feces varied widely among individuals, but were generally high (6.0 x 10(1) to 2.5 x 10(9) g(-1) wet weight). Of 39 E. coli isolates from L. argentatus, 67% had banding patterns that were > or = 90% similar to those from wastewater and trash, whereas only 39% of 36 L. marinus isolates exhibited > or = 90% similarity to these sources. Strains of E. coli from gulls matched (> or = 90% similarity) more strains from wastewater (39% matching) than from trash (15% matching). E. coli isolates from L. marinus feces exhibited a greater diversity of banding patterns than did isolates from L. argentatus. There were more unique E. coli banding patterns in trash samples than in wastewater, and higher diversity indices in the former compared to the latter. These findings suggest that both species of gulls, especially L. argentatus, obtain fecal bacteria from wastewater and landfill trash, which they may transport to recreational beaches and waters. Our results also indicate that E. coli populations may vary widely between gull species, and between the anthropogenic habitats that they frequent, i.e. landfills and wastewater treatment facilities.

  10. Generalized INverse imaging (GIN): ultrafast fMRI with physiological noise correction.

    Science.gov (United States)

    Boyacioğlu, Rasim; Barth, Markus

    2013-10-01

    An ultrafast functional magnetic resonance imaging (fMRI) technique, called generalized inverse imaging (GIN), is proposed, which combines inverse imaging with a phase constraint-leading to a less underdetermined reconstruction-and physiological noise correction. A single 3D echo planar imaging (EPI) prescan is sufficient to obtain the necessary coil sensitivity information and reference images that are used to reconstruct standard images, so that standard analysis methods are applicable. A moving dots stimulus paradigm was chosen to assess the performance of GIN. We find that the spatial localization of activation for GIN is comparable to an EPI protocol and that maximum z-scores increase significantly. The high temporal resolution of GIN (50 ms) and the acquisition of the phase information enable unaliased sampling and regression of physiological signals. Using the phase time courses obtained from the 32 channels of the receiver coils as nuisance regressors in a general linear model results in significant improvement of the functional activation, rendering the acquisition of external physiological signals unnecessary. The proposed physiological noise correction can in principle be used for other fMRI protocols, such as simultaneous multislice acquisitions, which acquire the phase information sufficiently fast and sample physiological signals unaliased. Copyright © 2012 Wiley Periodicals, Inc.

  11. Geosciences Information Network (GIN): A modular, distributed, interoperable data network for the geosciences

    Science.gov (United States)

    Allison, M.; Gundersen, L. C.; Richard, S. M.; Dickinson, T. L.

    2008-12-01

    A coalition of the state geological surveys (AASG), the U.S. Geological Survey (USGS), and partners will receive NSF funding over 3 years under the INTEROP solicitation to start building the Geoscience Information Network (www.geoinformatics.info/gin) a distributed, interoperable data network. The GIN project will develop standardized services to link existing and in-progress components using a few standards and protocols, and work with data providers to implement these services. The key components of this network are 1) catalog system(s) for data discovery; 2) service definitions for interfaces for searching catalogs and accessing resources; 3) shared interchange formats to encode information for transmission (e.g. various XML markup languages); 4) data providers that publish information using standardized services defined by the network; and 5) client applications adapted to use information resources provided by the network. The GIN will integrate and use catalog resources that currently exist or are in development. We are working with the USGS National Geologic Map Database's existing map catalog, with the USGS National Geological and Geophysical Data Preservation Program, which is developing a metadata catalog (National Digital Catalog) for geoscience information resource discovery, and with the GEON catalog. Existing interchange formats will be used, such as GeoSciML, ChemML, and Open Geospatial Consortium sensor, observation and measurement MLs. Client application development will be fostered by collaboration with industry and academic partners. The GIN project will focus on the remaining aspects of the system -- service definitions and assistance to data providers to implement the services and bring content online - and on system integration of the modules. Initial formal collaborators include the OneGeology-Europe consortium of 27 nations that is building a comparable network under the EU INSPIRE initiative, GEON, Earthchem, and GIS software company ESRI

  12. cotton fabric 51

    African Journals Online (AJOL)

    DR. AMINU

    1Department of Chemistry, Federal College of Education, Kano – Nigeria. 2Department of ... its versatility were examined taken into consideration, the molecular structure. ... hemicelluloses, pectin, coloring matter and ash ... temperature for a fixed period of time. These processes rendered the cotton 99% cellulose in nature.

  13. Cotton, Prof. Frank Albert

    Indian Academy of Sciences (India)

    ... Lecture Workshops · Refresher Courses · Symposia · Live Streaming. Home; Fellowship. Fellow Profile. Elected: 1985 Honorary. Cotton, Prof. Frank Albert. Date of birth: 9 April 1930. Date of death: 20 February 2007. Last known address: Department of Chemistry, Texas A & M University, College Station, TX 77843, U.S.A..

  14. Cotton regeneration in vitro

    Science.gov (United States)

    H. F. Sakhanokho and K. Rajasekaran Over the years, plant breeders have improved cotton via conventional breeding methods, but these methods are time-consuming. To complement classical breeding and, at times, reduce the time necessary for new cultivar development, breeders have turned to in vitro ...

  15. Advanced Exploration Systems Logistics Reduction and Repurposing Trash-to-Gas and Heat Melt Compactor KSC

    Science.gov (United States)

    Caraccio, Anne J.; Layne, Andrew; Hummerick, Mary

    2013-01-01

    Topics covered: 1. Project Structure 2. "Trash to Gas" 3. "Smashing Trash! The Heat Melt Compactor" 4. "Heat Melt Compaction as an Effective Treatment for Eliminating Microorganisms from Solid Waste" Thermal degradation of trash reduces volume while creating water, carbon dioxide and ash. CO2 can be fed to Sabatier reactor for CH4 production to fuel LOX/LCH4 ascent vehicle. Optimal performance: HFWS, full temperature ramp to 500-600 C. Tar challenges exist. Catalysis: Dolomag did eliminate allene byproducts from the product stream. 2nd Gen Reactor Studies. Targeting power, mass, time efficiency. Gas separation, Catalysis to reduce tar formation. Microgravity effects. Downselect in August will determine where we should spend time optimizing the technology.

  16. Archaeal orthologs of Cdc45 and GINS form a stable complex that stimulates the helicase activity of MCM.

    Science.gov (United States)

    Xu, Yuli; Gristwood, Tamzin; Hodgson, Ben; Trinidad, Jonathan C; Albers, Sonja-Verena; Bell, Stephen D

    2016-11-22

    The regulated recruitment of Cdc45 and GINS is key to activating the eukaryotic MCM(2-7) replicative helicase. We demonstrate that the homohexameric archaeal MCM helicase associates with orthologs of GINS and Cdc45 in vivo and in vitro. Association of these factors with MCM robustly stimulates the MCM helicase activity. In contrast to the situation in eukaryotes, archaeal Cdc45 and GINS form an extremely stable complex before binding MCM. Further, the archaeal GINS•Cdc45 complex contains two copies of Cdc45. Our analyses give insight into the function and evolution of the conserved core of the archaeal/eukaryotic replisome.

  17. Out of Site & Out of Mind: Speculative Historiographies of Techno Trash

    Directory of Open Access Journals (Sweden)

    Mél Hogan

    2015-06-01

    Full Text Available Out of Site & Out of Mind: Speculative Historiographies of Techno Trash by Mel Hogan and Andrea Zeffiro. Our contribution to the “Aesthetics of Trash” introduces an online participatory storytelling project, Speculative Historiographies of Techno Trash (technotrash.org. In its current iteration, technotrash.org is a website through which we are soliciting and featuring personal written reflections on the consumption and disposal of media technologies. Our project goal is to render the material and immaterial residues generated from of our everyday media practices more visible by accentuating the ecological and ethical dilemmas posed by the production, consumption, and disposal of media technologies.

  18. Potential for radioactive patient excreta in hospital trash and medical waste

    International Nuclear Information System (INIS)

    Evdokimoff, V.; Cash, C.; Buckley, K.

    1994-01-01

    Radioactive excreta from nuclear medicine patients can enter solid waste as common trash and medical biohazardous waste. Many landfills and transfer stations now survey these waste streams with scintillation detectors which may result in rejection of a hospital's waste. Our survey indicated that on the average either or both of Boston University Medical Center Hospital's waste streams can contain detectable radioactive excreta on a weekly basis. To avoid potential problems, radiation detectors were installed in areas where housekeepers carting trash and medical waste must pass through to ensure no radioactivity leaves the institution. 3 refs

  19. Evaluation of cotton stalks destroyers

    OpenAIRE

    Bianchini, Aloisio; Borges, Pedro H. de M.

    2013-01-01

    The destruction of the cotton crop residues (cotton stalks) is a mandatory procedure in Brazil for prophylactic issues, but is a subject unexplored by the research and there are few studies that deal with this issue. However, this is not encouraged in recent decades, studies aimed at developing and evaluating equipment for this purpose. The present study had the objective to evaluate six methods for mechanical destruction of cotton crop residues. Each method was defined based on the principle...

  20. Matter Unmoored: Trash, Archaeological Consciousness and American Culture and Fiction in the 1980s

    NARCIS (Netherlands)

    Jelfs, Tim

    This article considers the cultural significance of the garbage panics of the 1980s, including the voyage of the infamous Mobro 4000 “garbage barge.” The article argues that the trash at the centre of these panics is important to our understanding of both the 1980s and the present because it

  1. Analysis of the trash elimination in the city of Belen, Pa; The case of aura dump

    International Nuclear Information System (INIS)

    Lopez de Araujo, M.; De Souza, S; Lobato, V.

    2010-01-01

    This work is about the challenge of Belen city in Brasil because of the urban waste problem. For that reason is important to improve public policies and increase the accessibility of the population to implant trash collection services successfully combined with the education. The geography in this context has a vital role as well as the environmental analysis

  2. Characterization of Volume F Trash from Four Recent STS Missions: Microbial Occurrence, Numbers, and Identifications

    Science.gov (United States)

    Strayer, Richard F.; Hummerick, Mary E.; Richards, Jeffrey T.; McCoy, LaShelle E.; Roberts, Michael S.; Wheeler, Raymond M.

    2011-01-01

    The fate of space-generated solid wastes, including trash, for future missions is under consideration by NASA. Several potential treatment options are under active technology development. Potential fates for space-generated solid wastes: Storage without treatment; storage after treatment(s) including volume reduction, water recovery, sterilization, and recovery plus recycling of waste materials. For this study, a microbial characterization was made on trash returned from four recent STS missions. The material analyzed were 'Volume F' trash and other bags of accompanying trash. This is the second of two submitted papers on these wastes. This first one covered trash content, weight and water content. Upon receipt, usually within 2 days of landing, trash contents were catalogued and placed into categories: drink containers, food waste, personal hygiene items, and packaging materials, i.e., plastic film and duct tape. Microbial counts were obtained with cultivatable counts on agar media and direct counts using Acridine Orange fluorescent stain (AODC). Trash bag surfaces, 25 square cm , were also sampled. Direct counts were approximately 1 x 10(exp 6) microbes/square cm and cultivatable counts ranged from 1 x 10 to 1 X 10(exp 4) microbes/ square cm-2. Aerobic microbes, aerobic sporeformers, and yeasts plus molds were common for all four missions. Waste items from each category were placed into sterile ziplock bags and 1.5 L sterile DI water added. These were then dispersed by hand shaking for 2 min. prior to inoculation of count media or determining AODC. In general, cultivatable microbes were found in drinks, food wastes, and personal hygiene items. Direct counts were usually higher than cultivatable counts. Some pathogens were found: Staphylococcus auerus, Escherichia coli (fecal wastes). Count ranges: drink pouches - AODC 2 x 10(exp 6) to 1 X 10(exp 8) g(sub fw) (exp -1); cultivatable counts variable between missions; food wastes: Direct counts were close to aerobic

  3. Response of cotton varieties to different environments: flowering behavior and fiber quality

    International Nuclear Information System (INIS)

    Jawdat, D.; Ayyoub, Z.; Elias, R.

    2012-01-01

    Flowering behavior and fiber quality traits were analyzed of six Gossypium hirsutum L. varieties and one G. barbadense variety that were cultivated in two environmentally different locations. Records of days after planting (DAP) at first floral bud emergence, DAP at first floral opening, plant height at first flower and nodes above white flower (NAWF) were analyzed statistically to study flowering behavior in both locations. Fiber traits were tested and records of micronaire, fiber length, strength, cohesion, elongation, ginning percentage, and weight of seed cotton were statistically analyzed to look for significant differences and correlations. Earliness and a decline in fiber strength, and fiber cohesion were obtained in varieties cultivated in Soujeh accompanied with an increase in ginning percentages. Uniquely, fiber elongation showed no significant differences in varieties between the two environments in both seasons. Our results indicated that stability in some fiber traits such as, micronaire, fiber length, strength and cohesion was a variety specific. Evidently, fiber elongation in our work was not affected by cultivation managements and environmental conditions which suggest the solid genetic bases that control this trait. (author)

  4. Response of cotton varieties to different environments flowering behavior and fiber quality

    International Nuclear Information System (INIS)

    Jawdat, D.; Ayyoubi, Z.; Al-Safadi, B.

    2015-01-01

    The flowering behavior and fiber quality traits were analyzed of six Gossypium hirsutum L. varieties and one G. barbadense variety that were cultivated in two environmentally different locations. Records of days after planting (DAP) at first floral bud emergence, DAP at first floral opening, plant height at first flower and nodes above white flower (NAWF) were analyzed statistically to study flowering behavior in both locations. Fiber traits were tested and records of micronaire, fiber length, strength, cohesion, elongation, ginning percentage, and weight of seed cotton were statistically analyzed to look for significant differences and correlations. Earliness and a decline in fiber strength, and fiber cohesion were obtained in varieties cultivated in Soujeh accompanied with an increase in ginning percentages. Uniquely, fiber elongation showed no significant differences in varieties between the two environments in both seasons. Our results indicated that stability in some fiber traits such as, micronaire, fiber length, strength and cohesion was a variety specific. Evidently, fiber elongation in our work was not affected by cultivation managements and environmental conditions which suggest the solid genetic bases that control this trait.(author)

  5. Victory Gin Lane. Starvation and Beverages in Orwell’s Nineteen Eighty-Four

    Directory of Open Access Journals (Sweden)

    Paolo Caponi

    2015-05-01

    Full Text Available Gin is an ubiquitous presence in the domestic and urban scenery of Nineteen Eighty-Four (1949. For a population mercilessly hungered, it represents a handy and cheap commodity item providing a fluid opportunity for social aggregation. Victory Gin, served “in handless chine mugs” (53, is part of the workers’ staple diet at the Ministry of Truth, and is sold “at ten cents the large nip” from the small bar (actually, “a mere hole in the wall”, 51 in the canteen; served with cloves, it is the “speciality” (79 of that disreputable place which is the Chestnut Tree Café, where Winston Smith once spotted three fallen-out-of-favor members of the Inner Party – Jones, Aaronson and Rutherford – drink it silently after their release from Oceania prison camps (79. As is typical of the fate of spirits in literature, gin also serves as self-medication and can fuel a kind of inner escapism. It is to make the world “look more cheerful” that Winston gulps it down “like a dose of medicine”, and only after the “shock” of swallowing it can he squeeze himself into his alcove and begin his diary (7; gin clears out Winston’s stomach (53, and is the ultima ratio against that prescient “dull ache” in his belly (105; 106 that originates after bumping into “the girl with dark hair” (later: Julia one evening outside Mr. Charrington’s shop.

  6. Prospective systematic review registration: perspective from the Guidelines International Network (G-I-N

    Directory of Open Access Journals (Sweden)

    Van der Wees Philip

    2012-02-01

    Full Text Available Abstract Clinical practice and public health guidelines are important tools for translating research findings into practice with the aim of assisting health practitioners as well as patients and consumers in health behavior and healthcare decision-making. Numerous programs for guideline development exist around the world, with growing international collaboration to improve their quality. One of the key features in developing trustworthy guidelines is that recommendations should be based on high-quality systematic reviews of the best available evidence. The review process used by guideline developers to identify and grade relevant evidence for developing recommendations should be systematic, transparent and unbiased. In this paper, we provide an overview of current international developments in the field of practice guidelines and methods to develop guidelines, with a specific focus on the role of systematic reviews. The Guidelines International Network (G-I-N aims to stimulate collaboration between guideline developers and systematic reviewers to optimize the use of available evidence in guideline development and to increase efficiency in the guideline development process. Considering the significant benefit of systematic reviews for the guideline community, the G-I-N Board of Trustees supports the international prospective register of systematic reviews (PROSPERO initiative. G-I-N also recently launched a Data Extraction Resource (GINDER to present and share data extracted from individual studies in a standardized template. PROSPERO and GINDER are complementary tools to enhance collaboration between guideline developers and systematic reviewers to allow for alignment of activities and a reduction in duplication of effort.

  7. Prospective systematic review registration: perspective from the Guidelines International Network (G-I-N).

    Science.gov (United States)

    Van der Wees, Philip; Qaseem, Amir; Kaila, Minna; Ollenschlaeger, Guenter; Rosenfeld, Richard

    2012-02-09

    Clinical practice and public health guidelines are important tools for translating research findings into practice with the aim of assisting health practitioners as well as patients and consumers in health behavior and healthcare decision-making. Numerous programs for guideline development exist around the world, with growing international collaboration to improve their quality. One of the key features in developing trustworthy guidelines is that recommendations should be based on high-quality systematic reviews of the best available evidence. The review process used by guideline developers to identify and grade relevant evidence for developing recommendations should be systematic, transparent and unbiased. In this paper, we provide an overview of current international developments in the field of practice guidelines and methods to develop guidelines, with a specific focus on the role of systematic reviews. The Guidelines International Network (G-I-N) aims to stimulate collaboration between guideline developers and systematic reviewers to optimize the use of available evidence in guideline development and to increase efficiency in the guideline development process. Considering the significant benefit of systematic reviews for the guideline community, the G-I-N Board of Trustees supports the international prospective register of systematic reviews (PROSPERO) initiative. G-I-N also recently launched a Data Extraction Resource (GINDER) to present and share data extracted from individual studies in a standardized template. PROSPERO and GINDER are complementary tools to enhance collaboration between guideline developers and systematic reviewers to allow for alignment of activities and a reduction in duplication of effort.

  8. Superhydrophobic cotton by fluorosilane modification

    CSIR Research Space (South Africa)

    Erasmus, E

    2009-12-01

    Full Text Available the treatment with fluorinated or silicon compounds)1-4 and by enhancing the surface roughness with a fractal structure5-8. Cotton, a cellulose-based material, that is greatly hydrophilic, is more benefited when made hydrophobic. Modification of cotton...

  9. Los Angeles Area Permit Holder Estimated Trash Load Reduction, Los Angeles CA, 2012, US EPA Region 9

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Los Angeles River has been designated as an impaired waterbody due to the large volume of trash it receives from the watershed. To address this problem a Total...

  10. San Francisco Bay Area Baseline Trash Loading Summary Results, San Francisco Bay Area CA, 2012, US EPA Region 9

    Data.gov (United States)

    U.S. Environmental Protection Agency — The San Francisco Bay Area stormwater permit sets trash control guidelines for discharges through the storm drain system. The permit covers Alameda, Contra Costa,...

  11. Impact of Bollgard cotton on Indian cotton production and Income of ...

    Indian Academy of Sciences (India)

    Impact of Bollgard cotton on Indian cotton production and Income of cotton farmers. Presentation made in the Seventy Second Annual Meeting Indian Academy of Sciences, Bangalore at Devi Ahilya Vishwavidyalaya Indore 11th November 2006.

  12. Influence of gamma radiation and freezing on emulsifying capacity of trash fish muscle

    International Nuclear Information System (INIS)

    Ghosh, S.K.; Lewis, N.F.

    1979-01-01

    The authors examined meat taken from seven different types of fish to determine its emulsifying capacity, i.e. once after treatment with γ-rays and once after frozen storage. The results showed that the shelf life of refrigerated trash fish with a low γ-radiation dose (100 Krad), which hardly affected the emulsifying capacity of the fishmeat, can be considerably extended. Trash fis frozen at -18 0 C should (apart from a few exceptions) be processed at the latest after one month's storage. Generally speaking however the emulsifying capacity of the fish musculature fell much more quickly in all species of fish after irradiation than it did during frozen storage. (orig./MG) 891 MG/orig.- 892 HIS [de

  13. Visual analysis of trash bin processing on garbage trucks in low resolution video

    Science.gov (United States)

    Sidla, Oliver; Loibner, Gernot

    2015-03-01

    We present a system for trash can detection and counting from a camera which is mounted on a garbage collection truck. A working prototype has been successfully implemented and tested with several hours of real-world video. The detection pipeline consists of HOG detectors for two trash can sizes, and meanshift tracking and low level image processing for the analysis of the garbage disposal process. Considering the harsh environment and unfavorable imaging conditions, the process works already good enough so that very useful measurements from video data can be extracted. The false positive/false negative rate of the full processing pipeline is about 5-6% at fully automatic operation. Video data of a full day (about 8 hrs) can be processed in about 30 minutes on a standard PC.

  14. Experimental study on hydraulic characteristic around trash rack of a pumping station

    Science.gov (United States)

    Zhou, MinZhe; Li, TongChun; Lin, XiangYang; Liu, XiaoQing; Ding, Yuan; Liu, GuangYuan

    2017-11-01

    This paper focuses on flow pattern around trash rack of intake of a pumping station project. This pumping station undertake the task of supplying up to 3,500,000 m3 water per day for a megacity. Considering the large flow rate, high lift, multi-pipe supply and long-time operation in this water conveyance pumping station, we built a physical model test to measure the flow velocity and observe the flow pattern to verify the reasonability of preliminary design. In this test, we set 3 layers of current meters around each trash rack of intake in reservoir to collect the flow velocity. Furthermore, we design 2 operating conditions of 9 pumps to observe the change of flow pattern. Finally, we found the velocity data were in a normal range under 2 different operating conditions of the 9 pump units.

  15. Sugarcane trash management assessed by the interaction of yield with soil properties

    Directory of Open Access Journals (Sweden)

    Flávio Carlos Dalchiavon

    2013-12-01

    Full Text Available Currently, sugarcane plays an important global role, particularly with a view to alternative energy sources. Thus, in a sugarcane field of the mill Vale do Paraná S/A Álcool e Açúcar, Rubineia, São Paulo State, managed under two green cane harvest systems (cane trash left on and cane trash removed from the soil, Pearson and spatial correlations between the sugarcane yield (variety RB855035 in the third cut and soil physical and chemical properties were studied to identify the property best correlated with stalk yield and the best harvest method. For this purpose, two geostatistical grids (121 sampling points on 1.30 ha were installed on a eutrophic Red Argisol (homogeneous slope of 0.065 m m-1, in 2011, to determine the properties: stalk yield and sugarcane plant population, and soil resistance to penetration, gravimetric moisture, bulk density, and carbon stock, in the layers 0-0.20 and 0.20-0.40 m. The data were analyzed by descriptive, linear correlation and geostatistical analysis. In both treatments, the property stand density was best correlated with sugarcane yield (r = 0.725 in the trash mulching treatment - TM and r = 0.769 in the trash removal treatment - TR. However, in relation to the soil properties, bulk density (0-0.20 m was best correlated (r = 0.305 in TM, r = 0.211 in TR. Similarly, from the spatial point of view, stand density was the property that best explained the sugarcane yield. However, in the TM treatment the density (0.20-0.40 m was the only soil property spatially correlated with stalk yield. The carbon stock in the soil of the TM was 11.5 % higher than in the TR treatment. Results of the TM treatment were best, also with regard to soil management and conservation.

  16. Radioactivity appearing at landfills in household trash of nuclear medicine patients: much ado about nothing?

    Science.gov (United States)

    Siegel, Jeffry A; Sparks, Richard B

    2002-03-01

    The U.S. NRC in 1997 removed its arbitrary 1.11 GBq (30 mCi) rule, which had been in existence for almost 50 y, and now many more patients receiving radionuclide therapy in nuclear medicine can be treated as outpatients. However, another problem has the potential to limit the short-lived reality of outpatient treatment unless nuclear medicine practitioners and the health physics community gets involved. Radioactive articles in the household trash of nuclear medicine patients are appearing at solid waste landfills that have installed radiation monitors to prevent the entry of any detectable radioactivity, and alarms are going off around the country. These monitors are set to alarm at extremely low activity levels. Some states may actually hold licensees responsible if a patient's radioactive household trash is discovered in a solid waste stream; this is another major reason [along with continued use of the 1.11 GBq (30 mCi) rule] why many licensees are still not releasing their radionuclide therapy patients. This is in spite of the fact that the radioactivity contained in released nuclear medicine therapy patients, let alone the much lower activity level contained in their potentially radioactive household wastes, poses a minimal hazard to the public health and safety or to the environment. Currently, there are no regulations governing the disposal of low-activity, rapidly-decaying radioactive materials found in the household trash of nuclear medicine patients, the performance of landfill radiation monitors, or the necessity of spectrometry equipment. Resources are, therefore, being unnecessarily expended by regulators and licensees in responding to radiation monitor alarms that are caused by these unregulated short-lived materials that may be mixed with municipal trash. Recommendations are presented that would have the effect of modifying the existing landfill regulations and practices so as to allow the immediate disposal of such wastes.

  17. Experimental and numerical studies on the treatment of wet astronaut trash by forced-convection drying

    Science.gov (United States)

    Arquiza, J. M. R. Apollo; Morrow, Robert; Remiker, Ross; Hunter, Jean B.

    2017-09-01

    During long-term space missions, astronauts generate wet trash, including food containers with uneaten portions, moist hygiene wipes and wet paper towels. This waste produces two problems: the loss of water and the generation of odors and health hazards by microbial growth. These problems are solved by a closed-loop, forced-convection, heat-pump drying system which stops microbial activity by both pasteurization and desiccation, and recovers water in a gravity-independent porous media condensing heat exchanger. A transient, pseudo-homogeneous continuum model for the drying of wet ersatz trash was formulated for this system. The model is based on the conservation equations for energy and moisture applied to the air and solid phases and includes the unique trash characteristic of having both dry and wet solids. Experimentally determined heat and mass transfer coefficients, together with the moisture sorption equilibrium relationship for the wet material are used in the model. The resulting system of differential equations is solved by the finite-volume method as implemented by the commercial software COMSOL. Model simulations agreed well with experimental data under certain conditions. The validated model will be used in the optimization of the entire closed-loop system consisting of fan, air heater, dryer vessel, heat-pump condenser, and heat-recovery modules.

  18. Ginés Pérez y su O Crux

    Directory of Open Access Journals (Sweden)

    Climent, José

    2002-12-01

    Full Text Available The exact names attributed to Ginés Pérez were never at all clear. His first appointment to the Cathedral in Valencia complicated matters even more when he was referred to with the Christian name of what appeared to be "Juan", which only added to the confusion as it lead us to believe that he was the only candidate to apply for that position. Today, however, we now know his true and full names: he was called Ginés Pérez de la Parra. We also know, for the first time, the exact date of his death. The quality of his compositions not only contributed to their popularity but gave rise to the works of other composers being attributed to him. The authorship of the majority of his compositions are considered anonymous, though they can be located in diverse archives. Even so, we cannot find a single copy of the O Crux attributed to his name, despite the numerous copies and their variants that abound in Region of Valencia.El nombre de Ginés Pérez nunca ha tenido la claridad de debía. Su primer nombramiento en la catedral de Valencia ya lo confunde añadiéndole el “Juan” lo que ya siembra confusión, además de sugerirnos que, posiblemente, fue llamado para ocupar el puesto sin oposición. Hoy conocemos toda su filiación: Ginés Pérez de la Parra, así como la fecha de su muerte, totalmente equivocada hasta ahora. La valía de sus composiciones motivó, además de la difusión de su obra, la atribución de composiciones de otros autores. La mayor parte de sus composiciones constan como "anónimos", si bien pueden encontrarse en distintos archivos. Del presente O crux, sin embargo, no hemos podido encontrar ninguna copia con su nombre, pese a las múltiples copias, con sus variantes, existentes en la Comunidad Valenciana.

  19. The GIN legal problems of multi-parties at the drill site

    International Nuclear Information System (INIS)

    Case, C.W.

    1991-01-01

    The presence of multiple parties working at a drilling site complicates the application of the environmental laws, rules and regulations. A critical decision prior to any physical activities needs to be made as to which person (i.e., company, partnership) will be charged with the obligation of being the designated Generator of hazardous waste for that site. This critical decision is dictated by the refusal of the EPA to assign more than one EPA Generator Identification Number (GIN) to a single drilling site. The decision as to which member of the multiple parties presence at the drill site will obtain the GIN has liability ramifications when a mistake is made in the cleanup of spilled hazardous waste or hazardous substances; an improper situation arises as to the transportation, storage, treatment and disposal of hazardous waste; the waste is improperly classified, or the biennial reporting of hazardous waste activities does not occur. Liability issues arise that go far beyond the ordinary contractual disputes seen in the past arising from drilling activities, with liability in some situations well in excess of any damage claims normally allowed under common law or statutory law in the State of Texas for non-environmental disputes. This paper reviews the liabilities and responsibilities of oil and gas drillers under the Resource Conservation and Recovery Act and the Comprehensive Environmental Response, Compensation and Liability Act

  20. Agrobacterium rhizogenes-induced cotton hairy root culture as an alternative tool for cotton functional genomics

    Science.gov (United States)

    Although well-accepted as the ultimate method for cotton functional genomics, Agrobacterium tumefaciens-mediated cotton transformation is not widely used for functional analyses of cotton genes and their promoters since regeneration of cotton in tissue culture is lengthy and labor intensive. In cer...

  1. Impact of efficient refuge policies for Bt cotton in India on world cotton trade

    OpenAIRE

    Singla, Rohit; Johnson, Phillip N.; Misra, Sukant K.

    2010-01-01

    India is a major cotton producing country in the world along with the U.S. and China. A change in the supply of and demand for cotton in the Indian market has the potential to have an impact on world cotton trade. This study evaluates the implications of efficient Bt cotton refuge policies in India on world and U.S. cotton markets. It can be hypothesized that increased refuge requirements for Bt cotton varieties in India could decrease the world supply of cotton because of the lower yield pot...

  2. Synthesis of Cotton from Tossa Jute Fiber and Comparison with Original Cotton

    Directory of Open Access Journals (Sweden)

    Md. Mizanur Rahman

    2015-01-01

    Full Text Available Cotton fibers were synthesized from tossa jute and characteristics were compared with original cotton by using FTIR and TGA. The FTIR results indicated that the peak intensity of OH group from jute cotton fibers occurred at 3336 cm−1 whereas the peak intensity of original cotton fibers occurred at 3338 cm−1. This indicated that the synthesized cotton fiber properties were very similar to the original cotton fibers. The TGA result showed that maximum rate of mass loss, the onset of decomposition, end of decomposition, and activation energy of synthesized cotton were higher than original cotton. The activation energy of jute cotton fibers was higher than the original cotton fibers.

  3. Effect of trash mulch and nitrogen application on the cane yield and quality of sugarcane variety thatta

    International Nuclear Information System (INIS)

    Junejo, S.S.; Talpur, R.N.; Panhwar, M.

    2014-01-01

    The study was carried out to investigate the effect of trash mulching and nitrogen application on the growth, yield and quality of sugarcane variety Thatta-10 at NSCRI, farm Thatta during 2008-09. The data revealed that the plots received 225 N kg ha-1+ trash mulch showed better results for cane yield, yield components and quality. It was further observed that that the plots with mulching and varying doses of nitrogen application had low weed occurrence as compared to control plots receiving 175 N kg ha-1 + no mulch. Economic analysis data revealed that there could be no additional income from the control treatment, which received low levels of N fertilizer (175 N kg/ha) with no mulching. However, all fertilizer levels with trash mulching proved profitable over control. Moreover, better response was observed at 225 N kg/ha+ trash mulch. It is recommended that 225 N kg ha-1 application with trash mulch was profitable for obtaining maximum production of sugarcane. (author)

  4. Sugarcane trash levels in soil affects the fungi but not bacteria in a short-term field experiment.

    Science.gov (United States)

    Rachid, C T C C; Pires, C A; Leite, D C A; Coutinho, H L C; Peixoto, R S; Rosado, A S; Salton, J; Zanatta, J A; Mercante, F M; Angelini, G A R; Balieiro, Fabiano de Carvalho

    2016-01-01

    The sugarcane in Brazil is passing through a management transition that is leading to the abolition of pre-harvest burning. Without burning, large amounts of sugarcane trash is generated, and there is a discussion regarding the utilization of this biomass in the industry versus keeping it in the field to improve soil quality. To study the effects of the trash removal on soil quality, we established an experimental sugarcane plantation with different levels of trash over the soil (0%, 50% and 100% of the original trash deposition) and analyzed the structure of the bacterial and fungal community as the bioindicators of impacts. The soil DNA was extracted, and the microbial community was screened by denaturing gradient gel electrophoresis in two different seasons. Our results suggest that there are no effects from the different levels of trash on the soil chemistry and soil bacterial community. However, the fungal community was significantly impacted, and after twelve months, the community presented different structures among the treatments. Copyright © 2016. Published by Elsevier Editora Ltda.

  5. Sugarcane trash levels in soil affects the fungi but not bacteria in a short-term field experiment

    Directory of Open Access Journals (Sweden)

    C.T.C.C Rachid

    2016-06-01

    Full Text Available Abstract The sugarcane in Brazil is passing through a management transition that is leading to the abolition of pre-harvest burning. Without burning, large amounts of sugarcane trash is generated, and there is a discussion regarding the utilization of this biomass in the industry versus keeping it in the field to improve soil quality. To study the effects of the trash removal on soil quality, we established an experimental sugarcane plantation with different levels of trash over the soil (0%, 50% and 100% of the original trash deposition and analyzed the structure of the bacterial and fungal community as the bioindicators of impacts. The soil DNA was extracted, and the microbial community was screened by denaturing gradient gel electrophoresis in two different seasons. Our results suggest that there are no effects from the different levels of trash on the soil chemistry and soil bacterial community. However, the fungal community was significantly impacted, and after twelve months, the community presented different structures among the treatments.

  6. Cotton : Market setting, trade policies, and issues

    OpenAIRE

    Baffes, John

    2004-01-01

    The value of world cotton production in 2000-01 has been estimated at about $20 billion, down from $35 billion in 1996-97 when cotton prices were 50 percent higher. Although cotton's share in world merchandise trade is insignificant (about 0.12 percent), it is very important to a number of developing countries. Cotton accounts for approximately 40 percent of total merchandise export earnin...

  7. Per preparare la ripresa: Progetto europeo GI-N2K, “Geographic Information – Need to Know”

    Directory of Open Access Journals (Sweden)

    Mauro Salvemini

    2014-02-01

    Full Text Available The GI-N2K project, coordinated by the Katholieke Universiteit Leuven, which began in October 2013, and formed by an international consortium of 31 partners (25  countries is funded by the Erasmus Lifelong Learning Programme, aims to reformulate  the Body of Knowledge in the field of Geographic Information Science and  Technology.

  8. The water footprint of cotton consumption

    NARCIS (Netherlands)

    Chapagain, Ashok; Hoekstra, Arjen Ysbert; Savenije, H.H.G.; Gautam, R.

    2005-01-01

    The consumption of a cotton product is connected to a chain of impacts on the water resources in the countries where cotton is grown and processed. The aim of this report is to assess the ‘water footprint’ of worldwide cotton consumption, identifying both the location and the character of the

  9. Effectiveness of Environmental Management Based on Trash in The City of Depok

    Directory of Open Access Journals (Sweden)

    Ismiyati

    2016-01-01

    Full Text Available Indonesian government efforts, particularly in the city of Depok, regarding decent and healthy environmental management in the waste sector have to be enhanced. This is a complex and diverse problems, even though the government has set into the form of Law (UU Number 18 Year 2008 on Waste Management to build a strategic partnership of stakeholders in waste management. The Government has also issued Government Regulation of the Republic of Indonesia Number 81 Year 2012 on “Management of household waste and household-like waste”. Further research is required on what extent that the implementation of waste management had been undertaken, as well as the necessity to study the methods of environmental insight in waste management. Waste management needs to be comprehensive and integrated from upstream to downstream, thus providing economic benefits, people healthiness and environmental safety. The purpose of this study is to analyze the effectiveness of environmental management based in Depok. This study uses qualitative design, which is to observe, understand and expose reality or empirical phenomena; hence the proper method used is descriptive method. Instrument to gather the data is completed by observation and in-depth interviews. The type of data required includes primary and secondary data. The informant is selected by purposive sampling, and data analysis is treated with triangulation technique. The results present that in the framework of the effectiveness of environmental management based trash in Depok showed that 1 Institutional Factor for Urban Waste Management of Depok has run properly, 2 Private partnership (commercial solution to be involved in urban waste management in Depok is being explored, 3 Applicable technology in fostering a culture of 3R (reduce, reuse and recycle on the entire community of Depok, has been done with the declaration of Depok Trash Care towards Trash Clean 2020 in March 2014.

  10. Thwarting one of cotton's nemeses

    International Nuclear Information System (INIS)

    Senft, D.

    1991-01-01

    There's not much good to be said for the pink bollworm, cotton's most destructive pest, except that it is being controlled to cut crop damage. Scientists have developed strategies, such as increasing native populations of predatory insects and pest-resistant cotton varieties. Thanks to research, growers today can also use cultural practices such as early plowdown of harvested cotton to break up stalks and bury overwintering pink bollworms. And they can disrupt normal mating by releasing sterile insects and using copies of natural compounds, called pheromones, that the pink bollworm uses to attract mates. Such strategies, together with judicious use of insecticides, put together in various combinations, form what is called an integrated pest management system

  11. Garbage is a man thing! Gender issues in the subculture of trash

    Directory of Open Access Journals (Sweden)

    Mayka Castellano

    2011-12-01

    Full Text Available In this article I analyze how the relationship between genders occur within the fan community as well as researchers of trash cinema. Starting from perspectives presented by paracinema researchers, and also from the observation of a sustained process of sociability that takes place in Orkut social network I investigate how the construction of the cult of masculinity existing in this type of movie is set in place, and also how the association of this type of consumption as a subculture contributes to the perpetuation of different approaches in gender.

  12. San Francisco Bay Area Base Line Trash Loading (5000 - 25000 gal/yr)

    Science.gov (United States)

    Marine debris degrades ocean habitats, endangers marine and coastal wildlife, causes navigation hazards, results in economic losses to industry and governments, and threatens human health and safety. EPA Pacific Southwest (Region 9) is tapping existing programs and resources to advance the prevention, reduction and clean-up of marine debris in the North Pacific Ocean. EPA Pacific Southwest activities build upon specific recommendations of the Interagency Marine Debris Coordinating Committee by targeting threats and sources of debris and responding to debris impacts. EPA is initiating a three-pronged effort to reduce sources of marine debris, prevent trash from entering the oceans, and assess the human and ecosystem impacts and potential for cleanup.

  13. San Francisco Bay Area Base Line Trash Loading (25001 - 50000 gal/yr)

    Science.gov (United States)

    Marine debris degrades ocean habitats, endangers marine and coastal wildlife, causes navigation hazards, results in economic losses to industry and governments, and threatens human health and safety. EPA Pacific Southwest (Region 9) is tapping existing programs and resources to advance the prevention, reduction and clean-up of marine debris in the North Pacific Ocean. EPA Pacific Southwest activities build upon specific recommendations of the Interagency Marine Debris Coordinating Committee by targeting threats and sources of debris and responding to debris impacts. EPA is initiating a three-pronged effort to reduce sources of marine debris, prevent trash from entering the oceans, and assess the human and ecosystem impacts and potential for cleanup.

  14. San Francisco Bay Area Base Line Trash Loading (2501 - 5000 gal/yr)

    Science.gov (United States)

    Marine debris degrades ocean habitats, endangers marine and coastal wildlife, causes navigation hazards, results in economic losses to industry and governments, and threatens human health and safety. EPA Pacific Southwest (Region 9) is tapping existing programs and resources to advance the prevention, reduction and clean-up of marine debris in the North Pacific Ocean. EPA Pacific Southwest activities build upon specific recommendations of the Interagency Marine Debris Coordinating Committee by targeting threats and sources of debris and responding to debris impacts. EPA is initiating a three-pronged effort to reduce sources of marine debris, prevent trash from entering the oceans, and assess the human and ecosystem impacts and potential for cleanup.

  15. San Francisco Bay Area Base Line Trash Loading (0-2500 gal/yr)

    Science.gov (United States)

    Marine debris degrades ocean habitats, endangers marine and coastal wildlife, causes navigation hazards, results in economic losses to industry and governments, and threatens human health and safety. EPA Pacific Southwest (Region 9) is tapping existing programs and resources to advance the prevention, reduction and clean-up of marine debris in the North Pacific Ocean. EPA Pacific Southwest activities build upon specific recommendations of the Interagency Marine Debris Coordinating Committee by targeting threats and sources of debris and responding to debris impacts. EPA is initiating a three-pronged effort to reduce sources of marine debris, prevent trash from entering the oceans, and assess the human and ecosystem impacts and potential for cleanup.

  16. Plastic Trash goes Biohybrid"-Rapid and Selective Functionalization of Inert Plastic Surfaces with Biomolecules

    DEFF Research Database (Denmark)

    Schiller, Stefan M; Kambhampati, Dev; Stengel, Gudrun

    2010-01-01

    The covalent functionalization of "inert" polymers such as polypropylene with biomolecules for biocompatible or biosensor surfaces is challenging. Here we present a powerful approach to covalently modify "inert" macromolecular surfaces with biomacromolecules reusing old plastic material. A special...... emphasis was placed on easily accessible materials and a process which is easy, fast, efficient, cheap, and reliable. "Plastic trash" (lids from Eppendorf® pipet tip containers) was used as a polymer substrate to demonstrate the use/reuse of commercial packing material to covalently modify this material...

  17. Exposição a fungos dos trabalhadores dos ginásios com piscina

    OpenAIRE

    Viegas, Carla Sofia Costa

    2010-01-01

    RESUMO - Os trabalhadores dos ginásios com piscinas apresentam maior prevalência de lesões fúngicas, como a Tinea pedis e a onicomicose, devido às características intrínsecas da sua actividade profissional, pois apresentam mais horas por dia de exposição à contaminação fúngica das superfícies. Esta situação verifica-se não só por serem os que mais frequentam os locais possíveis de estarem contaminados, como é o caso de balneários, vestiários e zona envolvente às piscinas, mas t...

  18. “Ginasticando”: parcerias e possibilidades da Ginástica na comunidade

    Directory of Open Access Journals (Sweden)

    PRISCILA LOPES

    2016-06-01

    Full Text Available O Projeto de Extensão “Ginasticando” tem como meta disseminar a Ginástica em Diamantina, MG. Tendo início em 2011, teve seus objetivos e metodologias modificadas de acordo com as demandas da região, diagnosticadas por meio de estudos e pesquisas na área da Educação Física escolar. Os principais resultados alcançados até o momento apontam para a necessidade de continuidade do projeto no sentido de contribuir para a ampliação do repertório de práticas corporais vivenciadas no ambiente escolar.

  19. Application of Optimum Compaction Energy in the Development of Bricks Made with Construction Trash Soils

    Directory of Open Access Journals (Sweden)

    T. Lopez-Lara

    2014-01-01

    Full Text Available In general, bricks frequently show different densities and therefore different resistances because the compaction energy is not considered in their production. Expansive soils represent a problem for light buildings over them because of volumetric instability. A generalized solution has been to extract them and substitute them by inert soil; thus they become construction trash. So, in this work the compaction energy aspect and the use of construction trash soils in the elaboration of resistant masonry bricks of homogeneous and controlled density are a new contribution in the production of bricks of better quality. First, the soil was stabilized with CaOH which leads to a decrease in its volumetric changes. Then, they were compacted with a specific energy for obtaining an optimal and maximum controlled density to ensure an increase in strength. Our results show that two optimal compaction energies can be considered with respect to the variation of optimum moisture in masonry bricks of expansive soil stabilized with lime. The first is when the optimal humidity reaches its smallest value (integrated soil lumps and the second is when humidity increases (disintegrated soil lumps, after reaching its lowest value. We also conclude that high compaction energy does not improve density values.

  20. China's Cotton Policy and the Impact of China's WTO Accession and Bt Cotton Adoption on the Chinese and U.S. Cotton Sectors

    OpenAIRE

    Cheng Fang; Bruce A. Babcock

    2003-01-01

    In this paper we provide an analysis of China's cotton policy and develop a framework to quantify the impact of both China's World Trade Organization (WTO) accession and Bt (Bacillus thuringiensis) cotton adoption on Chinese and U.S. cotton sectors. We use a Chinese cotton sector model consisting of supply, demand, price linkages, and textiles output equations. A two-stage framework model provides gross cropping area and total area for cotton and major subsitute crops from nine cotton-produci...

  1. Cocoa/Cotton Comparative Genomics

    Science.gov (United States)

    With genome sequence from two members of the Malvaceae family recently made available, we are exploring syntenic relationships, gene content, and evolutionary trajectories between the cacao and cotton genomes. An assembly of cacao (Theobroma cacao) using Illumina and 454 sequence technology yielded ...

  2. Cotton fiber quality determined by fruit position, temperature and management

    OpenAIRE

    Wang, X.; Evers, J.B.; Zhang, L.; Mao, L.; Pan, X.; Li, Z.

    2013-01-01

    CottonXL is a tool to explore cotton fiber quality in relation to fruit position, to improve cotton quality by optimizing cotton plant structure, as well as to help farmers understand how the structure of the cotton plant determines crop growth and quality.

  3. 7 CFR 1205.319 - Cotton-producing region.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 10 2010-01-01 2010-01-01 false Cotton-producing region. 1205.319 Section 1205.319... Cotton Research and Promotion Order Definitions § 1205.319 Cotton-producing region. Cotton-producing region means each of the following groups of cotton-producing States: (a) Southeast Region: Alabama...

  4. Twirling Trash

    Science.gov (United States)

    Ashley, Susan

    2011-01-01

    The process of finding inspiration for a class project is fascinating and intriguing. In this article, the author describes a class project inspired by the gyre, a widespread circulating rotation or vortex of ocean currents, known as the Great Pacific Garbage Patch. This particular gyre is the location of an enormous floating mass of garbage,…

  5. Lesões desportivas na ginástica artística: estudo a partir de morbidade referida

    OpenAIRE

    Hoshi,Rosangela Akemi; Pastre,Carlos Marcelo; Vanderlei,Luiz Carlos Marques; Netto Júnior,Jayme; Bastos,Fábio do Nascimento

    2008-01-01

    INTRODUÇÃO: Os níveis de exigência biomecânica devidos ao alto grau de dificuldade na realização de gestos fazem da ginástica artística (GA) uma modalidade com elevado risco de lesões. Assim, é necessário que os aspectos a elas relacionados sejam controlados. OBJETIVO: Analisar a ocorrência de lesões na Ginástica Artística, associando-as a fatores de risco específicos da modalidade e do atleta, a partir de inquérito de morbidade referida. MÉTODOS: Foram entrevistados 54 ginastas, recrutados a...

  6. Assessment of Bollgard II cotton pollen mediated transgenes flow to ...

    African Journals Online (AJOL)

    Assessment of Bollgard II cotton pollen mediated transgenes flow to conventional cotton in the farming conditions of Burkina ... This has led to experiment on Bt cotton from 2003 to 2007. ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

  7. Aqueous supercapacitors on conductive cotton

    KAUST Repository

    Pasta, Mauro; La Mantia, Fabio; Hu, Liangbing; Deshazer, Heather Dawn; Cui, Yi

    2010-01-01

    Wearable electronics offer the combined advantages of both electronics and fabrics. In this article, we report the fabrication of wearable supercapacitors using cotton fabric as an essential component. Carbon nanotubes are conformally coated onto the cotton fibers, leading to a highly electrically conductive interconnecting network. The porous carbon nanotube coating functions as both active material and current collector in the supercapacitor. Aqueous lithium sulfate is used as the electrolyte in the devices, because it presents no safety concerns for human use. The supercapacitor shows high specific capacitance (~70-80 F·g-1 at 0.1 A·g-1) and cycling stability (negligible decay after 35,000 cycles). The extremely simple design and fabrication process make it applicable for providing power in practical electronic devices. © 2010 Tsinghua University Press and Springer-Verlag Berlin Heidelberg.

  8. Aqueous supercapacitors on conductive cotton

    KAUST Repository

    Pasta, Mauro

    2010-06-01

    Wearable electronics offer the combined advantages of both electronics and fabrics. In this article, we report the fabrication of wearable supercapacitors using cotton fabric as an essential component. Carbon nanotubes are conformally coated onto the cotton fibers, leading to a highly electrically conductive interconnecting network. The porous carbon nanotube coating functions as both active material and current collector in the supercapacitor. Aqueous lithium sulfate is used as the electrolyte in the devices, because it presents no safety concerns for human use. The supercapacitor shows high specific capacitance (~70-80 F·g-1 at 0.1 A·g-1) and cycling stability (negligible decay after 35,000 cycles). The extremely simple design and fabrication process make it applicable for providing power in practical electronic devices. © 2010 Tsinghua University Press and Springer-Verlag Berlin Heidelberg.

  9. ECONOMIC EVALUATION OF MAINTAINING THE CAPACITY OF TRASH RACKS IN HYDRAULIC ENGINEERING STRUCTURES

    Directory of Open Access Journals (Sweden)

    Natalia Walczak

    2017-05-01

    Full Text Available Considering the limited capabilities of obtaining energy in a traditional way from coal combustion and the requirements of the European Union, other alternative energy sources should be sought. They have been being increasingly used by business entities and individual investors and are designed to provide financial profits, which will be ensured only with correct operation of the energy system. One of examples of alternative energy sources application is the construction of small hydropower plants, where the efficiency of all elements included is of great importance. The article analyses financial losses incurred by owners of power plants when the energy system lacks 100% capacity of the inlet channel. Material that accumulates on SHP trash racks might be analysed in two ways: biologically (these are screenings – as in wastewater treatment plants and hydraulically.

  10. Estimation of best parents parents and superior cross combinations for yield and fiber quality related traits in upland cotton (gossypium hirsutum L.)

    International Nuclear Information System (INIS)

    Shaukat, S.; Khan, T.M.; Ijaz, S.

    2013-01-01

    Combining ability was studied for identification of potential cultivars and hybrids in upland cotton (Gossypium hirsutum L.) in a 6x6 set of diallel crosses among six genotypes of cotton, i.e., VH-232, CRS-2007, SB-149, GR-156, FH-207, and MARVI carried out on fiber length, fiber fineness, fiber elongation, fiber strength, ginning out tern (GOT) and seed cotton yield. Analysis of variance revealed highly significant (p < 0.01) differences among the genotypes for all traits. Combining ability studies showed that the mean squares, due to general combining ability (GCA), specific combining ability (SCA) and reciprocal effects were highly significant in F1 generation. Genetic components, due to GCA and SCA, revealed that traits, such as, fiber length, strength and fineness, showed high proportion of additive type of gene action in F1 generation because of greater GCA variances were greater than SCA variance. GR-156 was the best combiner for lint percentage and fiber length. FH-207 was the best combiner for fiber fineness. FH-207, MARVI and SB-149 were the best general combiners for fiber character and were suggested to be used in future breeding programme to improve fiber quality traits. CRS-2007 x GR-156, CRS-2007 x MARVI, SB-149 x MARVI and VH-232 x SB-149 had higher specific combining ability and reciprocal effects and they can be used for future breeding programme to improve fiber quality. (author)

  11. Cotton transformation via pollen tube pathway.

    Science.gov (United States)

    Wang, Min; Zhang, Baohong; Wang, Qinglian

    2013-01-01

    Although many gene transfer methods have been employed for successfully obtaining transgenic cotton, the major constraint in cotton improvement is the limitation of genotype because the majority of transgenic methods require plant regeneration from a single transformed cell which is limited by cotton tissue culture. Comparing with other plant species, it is difficult to induce plant regeneration from cotton; currently, only a limited number of cotton cultivars can be cultured for obtaining regenerated plants. Thus, development of a simple and genotype-independent genetic transformation method is particularly important for cotton community. In this chapter, we present a simple, cost-efficient, and genotype-independent cotton transformation method-pollen tube pathway-mediated transformation. This method uses pollen tube pathway to deliver transgene into cotton embryo sacs and then insert foreign genes into cotton genome. There are three major steps for pollen tube pathway-mediated genetic transformation, which include injection of -foreign genes into pollen tube, integration of foreign genes into plant genome, and selection of transgenic plants.

  12. Field test of trash removal screen utilizing current energy in irrigation canal; Ryusui energy wo riyoshita suisha jojinki no jissho shiken ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Goto, M; Katayama, S [National Research Institute of Agricultural Engineering, Tsukuba (Japan)

    1996-10-27

    A trash removal system working by current energy has been developed for agricultural waterway. It consists of a wheel, shaft, screen and conveyor to exhaust collected trash. Current energy is converted by the wheel into rotational power, which drives the screen lake and conveyor. It is installed in an agricultural water way, 1.2m wide, 1/5000 in gradient and 1m/s in flow speed. Observed in the field test were service conditions of the system and torque limiter, water level at each portion, wheel speed, and types and quantity of trash collected. It is found to be serviceable at a low cost. The troubles, such as noise and bent lake occurring when the chain is out of place, have been solved. The test also has clarified types of trash discarded in the waterway. 3 refs., 11 figs.

  13. Passive and active protection of cotton textiles

    NARCIS (Netherlands)

    Bochove, C. van

    1967-01-01

    In rotproofing of cotton a distinction is made between passive and active protection. In passive protection, the structure of the cotton fibre is modified in such a way that the fibre can longer be attacked. This modification of structure can be effected on different levels: microscopical,

  14. Fiber quality challenges facing the cotton industry

    Science.gov (United States)

    The cotton industry is in the midst of an exciting time with increased domestic consumption, but also facing pressure from other crops and the global marketplace. In order to ensure the US cotton crop remains the fiber of choice for the world it is important to keep an eye on the challenges to fibe...

  15. Within canopy distribution of cotton seed N

    Science.gov (United States)

    Whole cotton seeds can be an important component of dairy rations. Nitrogen content of the seed is an important determinant of the feed value of the seed. Efforts to increase the seed value as feed will be enhanced with knowledge of the range and distribution of seed N within the cotton crop. This s...

  16. Milkweed, stink bugs, and Georgia cotton

    Science.gov (United States)

    In peanut-cotton farmscapes in Georgia, stink bugs, i.e., Nezara viridula (L.)(Say) and Chinavia hilaris (Say), develop in peanut and then disperse at the crop-to-crop interface to feed on fruit in cotton. The main objective of this study was to examine the influence of a habitat of tropical milkwe...

  17. Cotton in Benin: governance and pest management

    NARCIS (Netherlands)

    Togbe, C.E.

    2013-01-01

    Key words: cotton, synthetic pesticides, neem oil (Azadirachta indica), Beauveria bassiana,

    Bacillus thuringiensis, field experiment, farmers’ participation

    Pests are one of the main factors limiting cotton production worldwide. Most of the pest

    control

  18. Remotely Measuring Trash Fluxes in the Flood Canals of Megacities with Time Lapse Cameras and Computer Vision Algorithms - a Case Study from Jakarta, Indonesia.

    Science.gov (United States)

    Sedlar, F.; Turpin, E.; Kerkez, B.

    2014-12-01

    As megacities around the world continue to develop at breakneck speeds, future development, investment, and social wellbeing are threatened by a number of environmental and social factors. Chief among these is frequent, persistent, and unpredictable urban flooding. Jakarta, Indonesia with a population of 28 million, is a prime example of a city plagued by such flooding. Yet although Jakarta has ample hydraulic infrastructure already in place with more being constructed, the increasingly severity of the flooding it experiences is not from a lack of hydraulic infrastructure but rather a failure of existing infrastructure. As was demonstrated during the most recent floods in Jakarta, the infrastructure failure is often the result of excessive amounts of trash in the flood canals. This trash clogs pumps and reduces the overall system capacity. Despite this critical weakness of flood control in Jakarta, no data exists on the overall amount of trash in the flood canals, much less on how it varies temporally and spatially. The recent availability of low cost photography provides a means to obtain such data. Time lapse photography postprocessed with computer vision algorithms yields a low cost, remote, and automatic solution to measuring the trash fluxes. When combined with the measurement of key hydrological parameters, a thorough understanding of the relationship between trash fluxes and the hydrology of massive urban areas becomes possible. This work examines algorithm development, quantifying trash parameters, and hydrological measurements followed by data assimilation into existing hydraulic and hydrological models of Jakarta. The insights afforded from such an approach allows for more efficient operating of hydraulic infrastructure, knowledge of when and where critical levels of trash originate from, and the opportunity for community outreach - which is ultimately needed to reduce the trash in the flood canals of Jakarta and megacities around the world.

  19. Using cotton plant residue to produce briquettes

    Energy Technology Data Exchange (ETDEWEB)

    Coates, W. [University of Arizona, Tucson, AZ (United States). Bioresources Research Facility

    2000-07-01

    In Arizona, cotton (Gossypium) plant residue left in the field following harvest must be buried to prevent it from serving as an overwintering site for insects such as the pink bollworm. Most tillage operations employed to incorporate the residue into the soil are energy intensive and often degrade soil structure. Trials showed that cotton plant residue could be incorporated with pecan shells to produce commercially acceptable briquettes. Pecan shell briquettes containing cotton residue rather than waste paper were slightly less durable, when made using equivalent weight mixtures and moisture contents. Proximate and ultimate analyses showed the only difference among briquette samples to be a higher ash content in those made using cotton plant residue. Briquettes made with paper demonstrated longer flame out time, and lower ash percentage, compared to those made with cotton plant residue. (author)

  20. Cotton for removal of aquatic oil spills

    International Nuclear Information System (INIS)

    Parker, H.W.; Fedler, C.B.; Heintz, C.E.; Nash, P.T.; Carr, D.L.; Lu, M.

    1992-01-01

    Raw cotton has considerable potential for selective removal of spilled oil and oil products from surface waters, since the natural waxes on the raw cotton make it preferentially oil wet. This potential was recognized in the early seventies at Texas Tech University. More recently other research workers have considered cotton as an adsorbent for spilled oil. The adsorbent market is now dominated by synthetic materials, such as air-blown polypropylene fiber, inorganic clays, and recycled paper and paper products. This paper further examines the potential of cotton in relation to these other adsorbents. Emphasis is placed on the potential for complete biodegradation of oil-soaked cotton adsorbents as a means avoiding the expense for incineration and/or the long-term environmental risk associated with placing the used adsorbents in landfills

  1. Trash measurement in middle sugar cane cultivars after the harvest; Quantificacao de palhico em diferentes cultivares medios de cana-de-acucar, apos a colheita

    Energy Technology Data Exchange (ETDEWEB)

    Santin, Ivan; Silva Neto, Helio F. da; Tasso Junior, Luiz Carlos; Marques, Diogo; Marques, Marcos O. [Universidade Estadual Paulista (FCAV/UNESP), Jaboticabal, SP (Brazil). Fac. de Ciencias Agrarias e Veterinarias. Dept. de Tecnologia], E-mail: santinivan@hotmail.com

    2010-07-01

    The introduction of mechanized harvesting of sugarcane made it possible to cut raw cane. Thus the amount of trash has produced a significant increase, which is important in that it can be used in the production of electricity through combustion. This study aimed to quantify the productivity of trash in the semi-mechanized harvesting of different middle sugarcane cultivars. The experiment was conducted at UNESP-Jaboticabal. The experimental design was a randomized block design with six treatments (cultivars) and three replications. At harvest, we counted the number of stems in the meter and the weight of stems was estimated agricultural productivity. After harvesting the cane, was used a rectangle of 4.5 m{sup 2}, which was placed randomly within each plot and all trash contained therein was weighed. Using these results to estimate the potential number of people who would benefit from the energy from this trash. Cultivar IAC94-4004 received the largest amount of trash (44.33 t ha- 1), IP (37.66%), Pd (38.00 x10-6) and TCH (118.00 t ha-1). Cultivar IAC95- 5000 obtained the less satisfactory results, generating a small amount of trash and therefore expressing lower potential energy. (author)

  2. Resolução temporal: desempenho de escolares no teste GIN - Gaps-in-noise Temporal resolution: performance of school-aged children in the GIN - Gaps-in-noise test

    Directory of Open Access Journals (Sweden)

    Maria Isabel Ramos do Amaral

    2010-12-01

    Full Text Available A habilidade auditiva denominada resolução temporal consiste no tempo mínimo necessário para resolver eventos acústicos, sendo fundamental para a compreensão de fala, e pode ser avaliada por testes de detecção de gaps, dentre eles o teste GIN - Gaps In Noise. OBJETIVO: Verificar o desempenho da resolução temporal em crianças sem queixas auditivas e/ou dificuldades escolares, no teste GIN, considerando-se o gênero masculino e feminino e a faixa etária de 8, 9 e 10 anos. FORMA DO ESTUDO: Coorte contemporânea com corte transversal prospectivo. MATERIAL E MÉTODO: O teste GIN foi aplicado em 75 escolares, reunidos em três grupos por faixa etária. RESULTADOS: Não foram encontradas diferenças significantes em relação às variáveis orelha e faixa etária. O gênero masculino obteve desempenho levemente melhor do que o feminino em relação apenas à porcentagem de acertos. CONCLUSÃO: A média do limiar de detecção de gaps e porcentagem de acertos foram calculados independente das variáveis orelha, gênero e faixa etária, sendo encontrados os valores de 4,7ms e 73,6%. Baseado no critério de intervalo de confiança 95% como corte para normalidade, os valores do limiar de detecção de gap e porcentagem de acertos foram 6,1ms e 60%, respectivamente.Time resolution hearing skill is the minimum time necessary to solve acoustic events, which is fundamental for speech understanding, and which may be assessed by gap-detection tests, such as the Gaps-in-noise test (GIN. AIM: the purpose of this study was to verify the performance of time processing ability in children with no hearing and/or education difficulties by applying the GIN test in both genders and ages from 8 to 10 years. STUDY DESIGN: a prospective cross-sectional contemporary cohort. MATERIAL AND METHOD: The GIN test was applied to 75 school-aged children separated into three groups by age. RESULTS: The findings showed no statistical differences among age groups or ears

  3. Honda WT20K1C 2 inch electric driven trash pump and Honda ES6500c generator

    International Nuclear Information System (INIS)

    1992-01-01

    Recovery of highly volatile hydrocarbon spills has always presented safety problems due to the explosive, flammable nature of the product being recovered. In an effort to increase safety, decrease spill response time, and improve recovery and/or pumping of hydrocarbons, an electric driven trash pump has been designed, developed, and tested. This pump has the capacity to recover and/or pump volatile and flammable substances such as condensate, gasoline, diesel fuel, and light gravity crude oil products in a safe manner. The pumping unit consists of an electric motor rated for use in hazardous locations, a trash pump with a Duraprene impeller and pump body, a motor/pump frame, and a Honda ES6500c generator that powers the pump motor through up to 100 feet of cable. A remote control switch is used to operate the unit so that workers can stay at least 30 m away while it is running. 5 figs

  4. Superamphiphobic cotton fabrics with enhanced stability

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Bi, E-mail: xubi@dhu.edu.cn [National Engineering Research Center for Dyeing and Finishing of Textiles, Donghua University, Shanghai 201620 (China); Key Laboratory of Science & Technology of Eco-Textile, Ministry of Education, Donghua University, Shanghai 201620 (China); College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai 201620 (China); Ding, Yinyan; Qu, Shaobo [College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai 201620 (China); Cai, Zaisheng, E-mail: zshcai@dhu.edu [College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai 201620 (China)

    2015-11-30

    Highlights: • Superamphiphobic cotton fabrics were prepared. • Water and hexadecane contact angels reach to 164.4° and 156.3°, respectively. • Nanoporous organically modified silica alcogel particles were synthesized. • The superamphiphobic cotton fabrics exhibit enhanced stability against abrasion, laundering and acid. - Abstract: Superamphiphobic cotton fabrics were prepared by alternately depositing organically modified silica alcogel (ormosil) particles onto chitosan precoated cotton fabrics and subsequent 1H, 1H, 2H, 2H-perfluorooctyltrimethoxysilane (PFOTMS) modification. Transmission electron microscopy and scanning electron microscopy images reveal that the ormosil particles display a fluffy, sponge-like nanoporous structure, and the entire cotton fiber surface is covered with highly porous networks. PFOTMS acts as not only a modifier to lower the surface energy of the cotton fabric but also a binder to enhance the coating stability against abrasion and washing. The treated cotton fabrics show highly liquid repellency with the water, cooking oil and hexadecane contact angels reaching to 164.4°, 160.1° and 156.3°, respectively. Meanwhile, the treated cotton fabrics exhibit good abrasion resistance and high laundering durability, which can withstand 10,000 cycles of abrasion and 30 cycles of machine wash without apparently changing the superamphiphobicity. The superamphiphobic cotton fabric also shows high acid stability, and can withstand 98% H{sub 2}SO{sub 4}. Moreover, the superamphiphobic coating has almost no influence on the other physical properties of the cotton fabrics including tensile strength, whiteness and air permeability. This durable non-wetting surface may provide a wide range of new applications in the future.

  5. Investigation of bio-regenerative life support and Trash-to-gas experiment on a 4 month mars simulation mission

    OpenAIRE

    Caraccio, A.; Poulet, Lucie; Hintze, P.; Miles, J.D.

    2014-01-01

    Future crewed missions to other planets or deep space locations will require regenerative Life Support Systems (LSS) as well as recycling processes for mission waste. Constant resupply of many commodity materials will not be a sustainable option for deep space missions, nor will stowing trash on board a vehicle or at a lunar or Martian outpost. The habitable volume will decline as the volume of waste increases. A complete regenerative environmentally controlled life support system (ECLSS) on ...

  6. 7 CFR 27.21 - Preparation of samples of cotton.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Preparation of samples of cotton. 27.21 Section 27.21... REGULATIONS COTTON CLASSIFICATION UNDER COTTON FUTURES LEGISLATION Regulations Inspection and Samples § 27.21 Preparation of samples of cotton. The samples from each bale shall be prepared as specified in this section...

  7. Minimization of operational impacts on spectrophotometer color measurements for cotton

    Science.gov (United States)

    A key cotton quality and processing property that is gaining increasing importance is the color of the cotton. Cotton fiber in the U.S. is classified for color using the Uster® High Volume Instrument (HVI), using the parameters Rd and +b. Rd and +b are specific to cotton fiber and are not typical ...

  8. Inheritance and segregation of exogenous genes in transgenic cotton

    Indian Academy of Sciences (India)

    Three transgenic cotton varieties (lines) were chosen for the study of inheritance and segregation of foreign Bt (Bacillus thuringiensis toxin) and tfdA genes in cotton. The transformed cotton varieties CCRI 30 and NewCott 33B expressing the Bt cryIA gene, and cotton line TFD expressing the tfdA gene were crossed with ...

  9. Increasing cotton stand establishment in soils prone to soil crusting

    Science.gov (United States)

    Many factors can contribute to poor cotton stand establishment, and cotton is notorious for its weak seedling vigor. Soil crusting can be a major factor hindering cotton seedling emergence in many of the cotton production regions of the US and the world. Crusting is mainly an issue in silty soils ...

  10. (Pleurotus pulmonarius) grown on cotton waste and cassava peel

    African Journals Online (AJOL)

    This work evaluated the yield of Pleurotus pulmonarius on different mixtures of cotton waste and cassava peel. P. pulmonarius demonstrated significantly higher colonization rate on cotton waste substrate (100 g cotton waste) 3 weeks after inoculation of spawn than any other substrate mixtures. Cotton waste had the ...

  11. Quantification of trash in early sugarcane cultivars; Quantificacao do palhico em cultivares precoces de cana-de-acucar

    Energy Technology Data Exchange (ETDEWEB)

    Pauli, Fernando A. de; Silva, Helio F. da; Tasso Junior, Luiz Carlos; Marques, Diogo; Marques, Marcos O. [Universidade Estadual Paulista (FCAV/UNESP), Jaboticabal, SP (Brazil). Fac. de Ciencias Agrarias e Veterinarias], E-mail: fernando_abackerli@hotmail

    2010-07-01

    The energy generated from biomass of sugarcane is on the spotlight on the world stage. The straw remaining in the soil after harvest of sugarcane, brings several attributes that qualify as plant material to be used for power cogeneration. Thus, this study aimed to quantify the straw in early cultivars of sugarcane. The experimental design was randomized blocks with 6 treatments (cultivars) and three replications. At harvest, we counted the number of stems on the meter and the weight of stems was estimated agricultural productivity. After harvesting the cane was used a rectangle of 4.5 m2, which was placed randomly within each plot and all trash contained therein was weighed. From these results was estimated the number of people benefiting the energy from this trash. The SP80-1842 had the best performance, the highest amounts of trash (31.00 t ha-1), the largest index value of straw (28.33%) and more people benefit from the energy generated from the same (26.66x10-1) showing its greater suitability for cogeneration. Cultivars CTC9 and SP91-1049 presented the results less satisfactory. (author)

  12. Separation and recycling of cotton from cotton/PET blends by depolymerization of PET catalyzed by bases and ionic liquids

    NARCIS (Netherlands)

    Bouwhuis, G.H. (Gerrit); Brinks, G.J. (Ger); Groeneveld, R.A.J. (Richard); Oelerich, J. (Jens)

    2014-01-01

    The recycling of post consumer cotton textile waste is highly requested, due to the high environmental impact of cotton production. Often cotton is mixed in blends with polyethylene terephthalate (PET). For the generation of high value products from recycled cotton, it essential that PET is

  13. Weed flora, yield losses and weed control in cotton crop

    OpenAIRE

    Jabran, Khawar

    2016-01-01

    Cotton (Gossypium spp.) is the most important fiber crop of world and provides fiber, oil, and animals meals. Weeds interfere with the growth activities of cotton plants and compete with it for resources. All kinds of weeds (grasses, sedges, and broadleaves) have been noted to infest cotton crop. Weeds can cause more than 30% decrease in cotton productivity. Several methods are available for weed control in cotton. Cultural control carries significance for weed control up to a certain extent....

  14. The Effect of Rate and Application Method of Potassium on Yield and Yield Components of Cotton in Saline Condition

    Directory of Open Access Journals (Sweden)

    A Ardakani

    2016-12-01

    flowering (25P+25V+50F, and 25% at planting+50% at vegetative stage and 25%at early boll development (25P+50V+25B as the subplot. The seeds planted had been acid-delinted and treated with chemicals against seed and seedling diseases. Plots consisted of six rows spaced 0.5 min row and 0.2 m in plant (10 plants m-2 and 6 m in length. To evaluate yield components of cotton including plant height, sympodial branch number, boll number, boll weight, 10 individual plants were selected randomly from final harvest area. At harvesting time one meter square from the beginning and a half meter around each plot was removed as a marginal effect. The remaining area was harvested by hand for determine of lint and biological yield. Seed-cotton samples were ginned to separate the fiber (lint from the seed. Lint percentage (% was calculated as the weight of lint to weight of the seed-cotton. The statistical analyses were performed by SAS software Ver. 9.1. The mean separation was done through Fischer least significant difference (FLSD test at alpha 0.05. Results and Discussion Analysis of variance showed that boll weight, seed cotton yield and biological yield were significantly affected by potassium rate, whereas plant height, number of sympodial branch, boll number and lint percentage was not affected by potassium rate. All traits were affected by potassium application method except plant height and lint percentage. Plant height, boll weight, seed cotton yield and lint percentage were affected by interaction of potassium rate and application method. Increasing of K level up to 150 kg ha-1 increased boll weight (23.64%, seed cotton yield (17.67%, and biological yield (9.86% in comparison with the application of 75 kg ha-1. Plant height, sympodial branch number and lint percentage did not respond to K rate. K application as 25% at planting+25% at vegetative stage (5-8 leaves stage, 25% at first flowering and 25% at early boll development (25P+25V+25F+25B had the highest boll weight, seed

  15. Examining cotton in rotation with rice and cotton in rotation with other crops using natural experiment

    Science.gov (United States)

    Sun, Ling; Zhu, Zesheng

    2017-08-01

    This paper is to show the ability of remote sensing image analysis combined with statistical analysis to characterize the environmental risk assessment of cotton in rotation with rice and cotton in rotation with other crops in two ways: (1) description of rotation period of cotton in rotation with rice and cotton in rotation with other crops by the observational study or natural experiment; (2) analysis of rotation period calculation of cotton in rotation with rice and cotton in rotation with other crops. Natural experimental results show that this new method is very promising for determining crop rotation period for estimating regional averages of environmental risk. When it is applied to determining crop rotation period, two requested remote sensing images of regional crop are required at least.

  16. Towards Sustainable Clothing Disposition: Exploring the Consumer Choice to Use Trash as a Disposal Option

    Directory of Open Access Journals (Sweden)

    Pamela S. Norum

    2017-07-01

    Full Text Available The textile and apparel supply chain plays an integral role in providing consumers with a continuous supply of apparel that must ultimately be discarded. Viewing the consumer as a player in the process between the supply chain and the post-consumer textile waste stream, this study was designed to explore the consumer apparel disposition process with an eye towards understanding how both supply chain members and post-consumer waste entities can interact with consumers to reduce the amount of apparel discarded in landfills. Hanson’s Consumer Product Disposition Process framework was used to help guide the research. Using a qualitative research approach, semi-structured in-depth interviews were conducted with twenty-four female consumers in the United States to address three main research questions. The findings revealed several themes: use of both “compensatory” and “non-compensatory” choice heuristics in decision making; a “usable life” and the “personal nature” of garments as barriers to non-trash disposal options; and the need to “create awareness” and “provide assurance” to encourage alternative disposal modes. Implications for apparel producers and retailers, secondhand stores and textile recyclers are discussed.

  17. The Cdc45/RecJ-like protein forms a complex with GINS and MCM, and is important for DNA replication in Thermococcus kodakarensis.

    Science.gov (United States)

    Nagata, Mariko; Ishino, Sonoko; Yamagami, Takeshi; Ogino, Hiromi; Simons, Jan-Robert; Kanai, Tamotsu; Atomi, Haruyuki; Ishino, Yoshizumi

    2017-10-13

    The archaeal minichromosome maintenance (MCM) has DNA helicase activity, which is stimulated by GINS in several archaea. In the eukaryotic replicative helicase complex, Cdc45 forms a complex with MCM and GINS, named as CMG (Cdc45-MCM-GINS). Cdc45 shares sequence similarity with bacterial RecJ. A Cdc45/RecJ-like protein from Thermococcus kodakarensis shows a bacterial RecJ-like exonuclease activity, which is stimulated by GINS in vitro. Therefore, this archaeal Cdc45/RecJ is designated as GAN, from GINS-associated nuclease. In this study, we identified the CMG-like complex in T. kodakarensis cells. The GAN·GINS complex stimulated the MCM helicase, but MCM did not affect the nuclease activity of GAN in vitro. The gene disruption analysis showed that GAN was non-essential for its viability but the Δgan mutant did not grow at 93°C. Furthermore, the Δgan mutant showed a clear retardation in growth as compared with the parent cells under optimal conditions at 85°C. These deficiencies were recovered by introducing the gan gene encoding the nuclease deficient GAN protein back to the genome. These results suggest that the replicative helicase complex without GAN may become unstable and ineffective in replication fork progression. The nuclease activity of GAN is not related to the growth defects of the Δgan mutant cells. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

  18. U.S. Cotton Prices and the World Cotton Market: Forecasting and Structural Change

    OpenAIRE

    Isengildina-Massa, Olga; MacDonald, Stephen

    2009-01-01

    The purpose of this study was to analyze structural changes that took place in the cotton industry in recent years and develop a statistical model that reflects the current drivers of U.S. cotton prices. Legislative changes authorized the U.S. Department of Agriculture to resume publishing cotton price forecasts for the first time in 79 years. In addition, systematic problems have become apparent in the forecasting models used by USDA and elsewhere, highlighting the need for an updated review...

  19. Identification of a New Cotton Disease Caused by an Atypical Cotton Leafroll Dwarf Virus in Argentina.

    Science.gov (United States)

    Agrofoglio, Yamila C; Delfosse, Verónica C; Casse, María F; Hopp, Horacio E; Kresic, Iván Bonacic; Distéfano, Ana J

    2017-03-01

    An outbreak of a new disease occurred in cotton (Gossypium hirsutum) fields in northwest Argentina starting in the 2009-10 growing season and is still spreading steadily. The characteristic symptoms of the disease included slight leaf rolling and a bushy phenotype in the upper part of the plant. In this study, we determined the complete nucleotide sequences of two independent virus genomes isolated from cotton blue disease (CBD)-resistant and -susceptible cotton varieties. This virus genome comprised 5,866 nucleotides with an organization similar to that of the genus Polerovirus and was closely related to cotton leafroll dwarf virus, with protein identity ranging from 88 to 98%. The virus was subsequently transmitted to a CBD-resistant cotton variety using Aphis gossypii and symptoms were successfully reproduced. To study the persistence of the virus, we analyzed symptomatic plants from CBD-resistant varieties from different cotton-growing fields between 2013 and 2015 and showed the presence of the same virus strain. In addition, a constructed full-length infectious cDNA clone from the virus caused disease symptoms in systemic leaves of CBD-resistant cotton plants. Altogether, the new leafroll disease in CBD-resistant cotton plants is caused by an atypical cotton leafroll dwarf virus.

  20. Mutagenesis in naturally coloured cotton

    International Nuclear Information System (INIS)

    Khatod, J.P.; Meshram, L.D.; Jain, P.P.

    2000-01-01

    The seeds of naturally coloured cotton were treated with 15 kR, 20 kR doses of gamma rays and 0.5% Ethyl Methane Sulphonate (EMS) and their combinations. The M 1 and M 2 generations were studied for mutagenic effectiveness and efficiency in inducing the useful mutants, spectrum of mutation and their effects on bract characters. Results obtained revealed that 15 kR and 20 kR doses were more effective in inducing the mutations. In G. hirsutum, significant differences were found for bract size and dry weight of bract was noted in 20 kR dose and low in 0.5% EMS in M 1 . In the M 2 generation increased ratio of bract surface area to lint weight per boll was noted in 20 kR + 0.5% EMS. (author)

  1. Imagens da prática profissional em academias de ginástica na cidade do Rio de Janeiro

    Directory of Open Access Journals (Sweden)

    Carlos Alberto de Andrade Coelho Filho

    2010-05-01

    Full Text Available O objetivo deste estudo é fornecer subsídios aos cursos de educação física, aproximando a formação profissional do campo de atuação em academias de ginástica. Através da análise de discurso, descrevemos e interpretamos a maneira como o profissional apresenta a si mesmo e a sua prática às outras pessoas, os meios pelos quais dirige e regula a impressão que formam a seu respeito e as atividades que pode ou não realizar. Os resultados confirmam que a prática do profissional de ginástica em academia vive momentos de tensão e impasse, o que implica a urgência de reformular a formação para essa prática nos cursos de graduação e de pós-graduação em educação física

  2. Producing Organic Cotton: A Toolkit - Crop Guide, Projekt guide, Extension tools

    OpenAIRE

    Eyhorn, Frank

    2005-01-01

    The CD compiles the following extension tools on organic cotton: Organic Cotton Crop Guide, Organic Cotton Training Manual, Soil Fertility Training Manual, Organic Cotton Project Guide, Record keeping tools, Video "Organic agriculture in the Nimar region", Photos for illustration.

  3. Cotton Transportation and Logistics: A Dynamic System

    OpenAIRE

    Robinson, John R.; Park, John L.; Fuller, Stephen

    2007-01-01

    The paper reviews the evolution of U.S. cotton transportation and logistics patterns over the last three decades. There have been many forces of change over this time period, with the largest change being a shift from primarily domestic market destinations to the international market. We describe the pre-1999 system and flow patterns when domestic consumption of U.S. cotton was dominant. We contrast this with current flow patterns as measured by available secondary export data and a sample of...

  4. Transgenic cotton expressing Cry10Aa toxin confers high resistance to the cotton boll weevil.

    Science.gov (United States)

    Ribeiro, Thuanne Pires; Arraes, Fabricio Barbosa Monteiro; Lourenço-Tessutti, Isabela Tristan; Silva, Marilia Santos; Lisei-de-Sá, Maria Eugênia; Lucena, Wagner Alexandre; Macedo, Leonardo Lima Pepino; Lima, Janaina Nascimento; Santos Amorim, Regina Maria; Artico, Sinara; Alves-Ferreira, Márcio; Mattar Silva, Maria Cristina; Grossi-de-Sa, Maria Fatima

    2017-08-01

    Genetically modified (GM) cotton plants that effectively control cotton boll weevil (CBW), which is the most destructive cotton insect pest in South America, are reported here for the first time. This work presents the successful development of a new GM cotton with high resistance to CBW conferred by Cry10Aa toxin, a protein encoded by entomopathogenic Bacillus thuringiensis (Bt) gene. The plant transformation vector harbouring cry10Aa gene driven by the cotton ubiquitination-related promoter uceA1.7 was introduced into a Brazilian cotton cultivar by biolistic transformation. Quantitative PCR (qPCR) assays revealed high transcription levels of cry10Aa in both T 0 GM cotton leaf and flower bud tissues. Southern blot and qPCR-based 2 -ΔΔCt analyses revealed that T 0 GM plants had either one or two transgene copies. Quantitative and qualitative analyses of Cry10Aa protein expression showed variable protein expression levels in both flower buds and leaves tissues of T 0 GM cotton plants, ranging from approximately 3.0 to 14.0 μg g -1 fresh tissue. CBW susceptibility bioassays, performed by feeding adults and larvae with T 0 GM cotton leaves and flower buds, respectively, demonstrated a significant entomotoxic effect and a high level of CBW mortality (up to 100%). Molecular analysis revealed that transgene stability and entomotoxic effect to CBW were maintained in T 1 generation as the Cry10Aa toxin expression levels remained high in both tissues, ranging from 4.05 to 19.57 μg g -1 fresh tissue, and the CBW mortality rate remained around 100%. In conclusion, these Cry10Aa GM cotton plants represent a great advance in the control of the devastating CBW insect pest and can substantially impact cotton agribusiness. © 2017 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

  5. The water footprint of cotton consumption: An assessment of the impact of worldwide consumption of cotton products on the water resources in the cotton producing countries

    NARCIS (Netherlands)

    Chapagain, Ashok; Hoekstra, Arjen Ysbert; Savenije, H.H.G.; Gautam, R.

    2006-01-01

    The consumption of a cotton product is connected to a chain of impacts on the water resources in the countries where cotton is grown and processed. The aim of this paper is to assess the ‘water footprint’ of worldwide cotton consumption, identifying both the location and the character of the

  6. STIFFNESS MODIFICATION OF COTTON IN CHITOSAN TREATMENT

    Directory of Open Access Journals (Sweden)

    CAMPOS Juan

    2017-05-01

    Full Text Available Chitosan is a biopolymer obtained from chitin, and among their most important aspects highlights its applications in a lot of industrial sectors due to its intrinsic properties, especially in the textile sector. In the last years, chitosan is widely used in the cotton and wool finishing processes due to its bond between them and its properties as an antifungical and antimicrobial properties. In this paper three different molecular weight chitosan are used in the finishing process of cotton to evaluate its influence in the surface properties modification. In order to evaluate the effect of the treatment with chitosan, flexural stiffness test is performed in warp and weft direction, and then the total value is calculated. The cotton fabric is treated with 5 g/L of different types of chitosan in an impregnation bath. This study shows the extent of surface properties modification of the cotton provided by three types of chitosan treatment. The results show that all types of chitosan modify the cotton flexural rigidity properties but the one which modifies it in a relevant manner is chitosan originated from shrimps. Chitosan, textile, flexural stiffnes, chitin, cotton.

  7. Lauretsius : Trash, pop&kitš ehk mäluta tsitaadid õhtumaade allakäigu ajastust = Trash, Pop&kitsch or quotations without memory from the era of the decline of the West / Andreas Trossek

    Index Scriptorium Estoniae

    Trossek, Andreas, 1980-

    2007-01-01

    Maalikunstnik Lauri Sillaku alias Lauretsiuse loomingust ja koostööst erinevate partneritega. Nende ühiseks visiitkaardiks kujunesid suured trash-maalid, tulvil apokalüptilist pinget ja grandioossust. Ta on armastanud alati "vinti üle keerata", millest kumab kitši toimeloogika tundmine ja selle ärakasutamine. Camp ja punk ei välista teineteist. Ta on maalinud ka Madalmaade renassansijärgse miniatuurmaali jälgedes pilte puuviljadest, kattes need kristlik-mütoloogilise tähenduskastme ja krakleega või on raamistanud ilutsevate raamidega isegi grafitit. Tommy nime all tegutses Toomas Tõnissoo

  8. Development and validation of SUCROS-Cotton : A potential crop growth simulation model for cotton

    NARCIS (Netherlands)

    Zhang, L.; Werf, van der W.; Cao, W.; Li, B.; Pan, X.; Spiertz, J.H.J.

    2008-01-01

    A model for the development, growth and potential production of cotton (SUCROS-Cotton) was developed. Particular attention was given to the phenological development of the plant and the plasticity of fruit growth in response to temperature, radiation, daylength, variety traits, and management. The

  9. 75 FR 50847 - Cotton Program Changes for Upland Cotton, Adjusted World Price, and Active Shipping Orders

    Science.gov (United States)

    2010-08-18

    ... Cotton Program Changes for Upland Cotton, Adjusted World Price, and Active Shipping Orders AGENCY... Assistance Program (EAAP) and clarifying the definition of ``active shipping order.'' DATES: Effective Date... address that matter this rule amends in the payment calculation for semi-processed and reginned motes in 7...

  10. 76 FR 32067 - Common Crop Insurance Regulations; Extra Long Staple Cotton Crop Provisions

    Science.gov (United States)

    2011-06-03

    ... ``Any AUP cotton'' and replacing it with the phrase ``Mature AUP cotton'' to clarify the AUP cotton must be mature in order to calculate a conversion factor between AUP cotton and ELS cotton. List of... dividing Price A by 85 percent of Price B. * * * * * (f) Mature AUP cotton harvested or appraised from...

  11. HVI Colorimeter and Color Spectrophotometer Relationships and Their Impacts on Developing "Traceable" Cotton Color Standards

    Science.gov (United States)

    Color measurements of cotton fiber and cotton textile products are important quality parameters. The Uster® High Volume Instrument (HVI) is an instrument used globally to classify cotton quality, including cotton color. Cotton color by HVI is based on two cotton-specific color parameters—Rd (diffuse...

  12. Investigation of Bio-Regenerative Life Support and Trash-to-Gas Experiment on a 4-Month Mars Simulation Mission

    Science.gov (United States)

    Caraccio, Anne; Poulet, Lucie; Hintze, Paul E.; Miles, John D.

    2014-01-01

    Future crewed missions to other planets or deep space locations will require regenerative Life Support Systems (LSS) as well as recycling processes for mission waste. Constant resupply of many commodity materials will not be a sustainable option for deep space missions, nor will stowing trash on board a vehicle or at a lunar or Martian outpost. The habitable volume will decline as the volume of waste increases. A complete regenerative environmentally controlled life support system (ECLSS) on an extra-terrestrial outpost will likely include physico-chemical and biological technologies, such as bioreactors and greenhouse modules. Physico-chemical LSS do not enable food production and bio-regenerative LSS are not stable enough to be used alone in space. Mission waste that cannot be recycled into the bio-regenerative ECLSS can include excess food, food packaging, clothing, tape, urine and fecal waste. This waste will be sent to a system for converting the trash into high value products. Two crew members on a 120 day Mars analog simulation, in collaboration with Kennedy Space Centers (KSC) Trash to Gas (TtG) project investigated a semi-closed loop system that treated non-edible biomass and other logistical waste for volume reduction and conversion into useful commodities. The purpose of this study is to show how plant growth affects the amount of resources required by the habitat and how spent plant material can be recycled. Real-time data was sent to the reactor at KSC in Florida for replicating the analog mission waste for laboratory operation. This paper discusses the 120 day mission plant growth activity, logistical and plant waste management, power and water consumption effects of the plant and logistical waste, and potential energy conversion techniques using KSCs TtG technology.

  13. Investigation of Bio-Regenerative Life Support and Trash-To-Gas Experiment on a 4 Month Mars Simulation Mission

    Science.gov (United States)

    Caraccio, Anne; Poulet, Lucie; Hintze, Paul E.; Miles, John D.

    2014-01-01

    Future crewed missions to other planets or deep space locations will require regenerative Life Support Systems (LSS) as well as recycling processes for mission waste. Constant resupply of many commodity materials will not be a sustainable option for deep space missions, nor will storing trash on board a vehicle or at a lunar or Martian outpost. The habitable volume will decline as the volume of waste increases. A complete regenerative environmentally controlled life support system (ECLSS) on an extra-terrestrial outpost will likely include physico-chemical and biological technologies, such as bioreactors and greenhouse modules. Physico-chemical LSS do not enable food production and bio-regenerative LSS are not stable enough to be used alone in space. Mission waste that cannot be recycled into the bio-regenerative ECLSS can include excess food, food packaging, clothing, tape, urine and fecal waste. This waste will be sent to a system for converting the trash into the high value products. Two crew members on a 120 day Mars analog simulation, in collaboration with Kennedy Space Centers (KSC) Trash to Gas (TtG) project investigated a semi-closed loop system that treated non-edible biomass and other logistical waste for volume reduction and conversion into useful commodities. The purposes of this study are to show the how plant growth affects the amount of resources required by the habitat and how spent plant material can be recycled. Real-time data was sent to the reactor at KSC in Florida for replicating the analog mission waste for laboratory operation. This paper discusses the 120 day mission plant growth activity, logistical and plant waste management, power and water consumption effects of the plant and logistical waste, and potential energy conversion techniques using KSCs TtG reactor technology.

  14. Physical model of a floating trash boom to control aquatic weeds at the TVA Widows Creek Fossil Plant

    International Nuclear Information System (INIS)

    Hopping, P.N.

    1991-01-01

    This paper reports that the Tennessee Valley Authority (TVA) Widows Creek Fossil plant seasonally encounters adverse accumulations of aquatic weeds at the intakes of the condenser cooling water pumps. To reduce the accumulations, a floating trash boom has been proposed for the intakes. To evaluate the hydraulic feasibility of a boom, a physical model of the intakes has been built at the TVA Engineering Laboratory. The model was used to determine the boom alignment and depth of skimming needed to successfully deflect weeds away from the intakes and provide self-cleaning

  15. Inheritance and segregation of exogenous genes in transgenic cotton

    Indian Academy of Sciences (India)

    1Key Laboratory of Cotton Genetic Improvement of the Ministry of Agriculture, Cotton Research Institute, Chinese. Academy of Agricultural Sciences, Anyang Henan 455 112, People's Republic of China. 2Institute ..... Athens, Greece. Xie D. X. ...

  16. The chemical recycle of cotton

    Directory of Open Access Journals (Sweden)

    Alice Beyer Schuch

    2016-08-01

    Full Text Available The chemical recycle of cotton textiles and/or other cellulosic materials for the purpose of manufacturing regenerated high quality textiles fibres is a novel process. The objective of related research is based on the forecast of population growth, on resource scarcity predictions, and on the negative environmental impact of the textile industry. These facts lead the need of broadening the scope for long-term textile-to-textile recycle - as the mechanical recycle of natural fibres serve for limited number of cycles, still depends on input of virgin material, and offer a reduced-in-quality output. Critical analysis of scientific papers, relevant related reports, and personal interviews were the base of this study, which shows viable results in laboratorial scale of using low-quality cellulosic materials as input for the development of high-quality regenerated textile fibres though ecological chemical process. Nevertheless, to scale up and implement this innovative recycle method, other peripheral structures are requested, such as recover schemes or appropriate sort, for instance. Further researches should also be considered in regards to colours and impurities.

  17. PREDICTING DEMAND FOR COTTON YARNS

    Directory of Open Access Journals (Sweden)

    SALAS-MOLINA Francisco

    2017-05-01

    Full Text Available Predicting demand for fashion products is crucial for textile manufacturers. In an attempt to both avoid out-of-stocks and minimize holding costs, different forecasting techniques are used by production managers. Both linear and non-linear time-series analysis techniques are suitable options for forecasting purposes. However, demand for fashion products presents a number of particular characteristics such as short life-cycles, short selling seasons, high impulse purchasing, high volatility, low predictability, tremendous product variety and a high number of stock-keeping-units. In this paper, we focus on predicting demand for cotton yarns using a non-linear forecasting technique that has been fruitfully used in many areas, namely, random forests. To this end, we first identify a number of explanatory variables to be used as a key input to forecasting using random forests. We consider explanatory variables usually labeled either as causal variables, when some correlation is expected between them and the forecasted variable, or as time-series features, when extracted from time-related attributes such as seasonality. Next, we evaluate the predictive power of each variable by means of out-of-sample accuracy measurement. We experiment on a real data set from a textile company in Spain. The numerical results show that simple time-series features present more predictive ability than other more sophisticated explanatory variables.

  18. Statistical t Analysis for the Solution of Prediction Trash Management in Dusun Tanjung Sari Kec. Ngaglik Kab Sleman, Yogyakarta

    International Nuclear Information System (INIS)

    Salmahaminati; Yahya, Amri; Husnaqilati, Atina

    2017-01-01

    Trash management is one of the society participation to have a good hygiene for each area or nationally. Trash is known as the remainder of regular consumption that should be disposed to do waste processing which will be beneficial and improve the hygiene. The way to do is by sorting plastic which is processed into goods in accordance with the waste. In this study, we will know what are the factors that affect the desire of citizens to process the waste. The factors would have the identity and the state of being of each resident, having known of these factors will be the education about waste management, so it can be compared how the results of the extension by using preliminary data prior to the extension and the final data after extension. The analysis uses multiple logistic regression is the identify factors that influence people’s to desire the waste while the comparison results using t analysis. Data is derived from statistical instrument in the form of a questionnaire. (paper)

  19. Fiber sample presentation system for spectrophotometer cotton fiber color measurements

    Science.gov (United States)

    The Uster® High Volume Instrument (HVI) is used to class U.S. cotton for fiber color, yielding the industry accepted, cotton-specific color parameters Rd and +b. The HVI examines a 9 square inch fiber sample, and it is also used to test large AMS standard cotton “biscuits” or rectangles. Much inte...

  20. At-line cotton color measurements by portable color spectrophotometers

    Science.gov (United States)

    As a result of reports of cotton bales that had significant color changes from their initial Uster® High Volume Instrument (HVI™) color measurements, a program was implemented to measure cotton fiber color (Rd, +b) at-line in remote locations (warehouse, mill, etc.). The measurement of cotton fiber...

  1. IMPROVED SPECTROPHOTOMETER FIBER SAMPLING SYSTEM FOR COTTON FIBER COLOR MEASUREMENTS

    Science.gov (United States)

    Cotton in the U.S. is classified for color using the Uster® High Volume Instrument (HVI), and the parameters Rd and +b are used to designate color grades for cotton fiber. However, Rd and +b are cotton-specific color parameters, and the need existed to demonstrate the relationships of Rd and +b to...

  2. 78 FR 68983 - Cotton Futures Classification: Optional Classification Procedure

    Science.gov (United States)

    2013-11-18

    ...-AD33 Cotton Futures Classification: Optional Classification Procedure AGENCY: Agricultural Marketing... regulations to allow for the addition of an optional cotton futures classification procedure--identified and... response to requests from the U.S. cotton industry and ICE, AMS will offer a futures classification option...

  3. Insecticide use and practices among cotton farmers in northern ...

    African Journals Online (AJOL)

    Cotton (Gossypium hirsutum L.) is an important cash crop in Uganda. Insecticide application practices among cotton growers in northern Uganda were examined to determine the pests targeted and the compliance of control measures with the standards recommended by the Uganda's Cotton Development Organization ...

  4. Genetic transformation of cry1EC gene into cotton ( Gossypium ...

    African Journals Online (AJOL)

    Cotton is the chief fibre crop of global importance. It plays a significant role in the national economy. Cotton crop is vulnerable to a number of insect species, especially to the larvae of lepidopteron pests. 60% insecticides sprayed on cotton are meant to control the damage caused by bollworm complex. Transgenic ...

  5. MicroRNA expression profiling during upland cotton gland forming ...

    African Journals Online (AJOL)

    Jane

    2011-08-15

    Aug 15, 2011 ... 2Key Laboratory of Cotton Genetic Improvement, Cotton Research Institute of the Chinese Academy of Agricultural. Sciences, Ministry of ... terpenoid aldehyde biosynthesis pathway, genetic engineering and molecular breeding of cotton. ... toxic to non-ruminant animals and humans, which means that large ...

  6. THE ELASTICITY OF EXPORT DEMAND FOR US COTTON

    OpenAIRE

    Paudel, Laxmi; Houston, Jack E.; Adhikari, Murali; Devkota, Nirmala

    2004-01-01

    There exist conflicting views among the researchers about the magnitudes of US cotton export demand elasticity, ranging from the highly inelastic to highly elastic. An Armington model was used to analyze the export demand elasticity of US Cotton. Our analysis confirms an elastic nature of US cotton export demand.

  7. 7 CFR 27.25 - Additional samples of cotton; drawing.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Additional samples of cotton; drawing. 27.25 Section... Samples § 27.25 Additional samples of cotton; drawing. In addition to the samples hereinbefore prescribed, separate samples, if desired, may be drawn and furnished to the owner of the cotton. ...

  8. 7 CFR 1427.23 - Cotton loan deficiency payments.

    Science.gov (United States)

    2010-01-01

    ..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS COTTON Nonrecourse Cotton Loan and Loan... intentions to receive a loan deficiency payment on the identified commodity or (ii) A completed request for a... cotton based on a locked-in adjusted world price, provide identifying numbers for modules or other...

  9. 7 CFR 1427.174 - Maturity of seed cotton loans.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 10 2010-01-01 2010-01-01 false Maturity of seed cotton loans. 1427.174 Section 1427.174 Agriculture Regulations of the Department of Agriculture (Continued) COMMODITY CREDIT CORPORATION... Maturity of seed cotton loans. Seed cotton loans mature on demand by CCC but no later than May 31 following...

  10. farmers' knowledge and perceptions of cotton insect pests and their

    African Journals Online (AJOL)

    Prince Acheampong

    A survey of 337 cotton farmers in the three northern regions of Ghana was ... five applications were made during the season. ... Keywords: cotton, farmer knowledge and perception, insect pest control, Ghana. .... bordered on tests of farmers' knowledge of cotton insect pests, their damage ..... Agricultural Experiment Station.

  11. Zinc comprising coordination compounds as growth stimulants of cotton seeds

    International Nuclear Information System (INIS)

    Yusupov, Z.N.; Nurmatov, T.M.; Rakhimova, M.M.; Dzhafarov, M.I.; Nikolaeva, T.B.

    1991-01-01

    Present article is devoted to zinc comprising coordination compounds as growth stimulants of cotton seeds. The influence of zinc coordination compounds with physiologically active ligands on germinative energy and seed germination of cotton was studied. The biogical activity and effectiveness of zinc comprising coordination compounds at application them for humidification of cotton seeds was studied as well.

  12. 7 CFR 1427.1203 - Eligible ELS cotton.

    Science.gov (United States)

    2010-01-01

    ... OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS COTTON Extra Long Staple (ELS) Cotton... must be either: (1) Baled lint, including baled lint classified by USDA's Agricultural Marketing..., under the provisions of this subpart, has been made available; (2) Imported ELS cotton; (3) Raw...

  13. Cotton Production in Mali: Subsidies or Sustainable Development?

    Science.gov (United States)

    Moore, Lindsey

    2007-01-01

    Current trade rules concerning cotton subsidies are intricately linked with poverty and hunger in Mali. Over half of Mali's economy and over 30 million people depend directly on cotton. It is the main cash crop and the most important source of export revenue. Cotton also plays a key role in development policies and in the fight against poverty by…

  14. Indian Bt cotton varieties do not affect the performance of cotton aphids.

    Directory of Open Access Journals (Sweden)

    Nora C Lawo

    Full Text Available Cotton varieties expressing Cry proteins derived from the soil bacterium Bacillus thuringiensis (Bt are grown worldwide for the management of pest Lepidoptera. To prevent non-target pest outbreaks and to retain the biological control function provided by predators and parasitoids, the potential risk that Bt crops may pose to non-target arthropods is addressed prior to their commercialization. Aphids play an important role in agricultural systems since they serve as prey or host to a number of predators and parasitoids and their honeydew is an important energy source for several arthropods. To explore possible indirect effects of Bt crops we here examined the impact of Bt cotton on aphids and their honeydew. In climate chambers we assessed the performance of cotton aphids, Aphis gossypii Glover (Hemiptera: Aphididae when grown on three Indian Bt (Cry1Ac cotton varieties (MECH 12, MECH 162, MECH 184 and their non-transformed near isolines. Furthermore, we examined whether aphids pick up the Bt protein and analyzed the sugar composition of aphid honeydew to evaluate its suitability for honeydew-feeders. Plant transformation did not have any influence on aphid performance. However, some variation was observed among the three cotton varieties which might partly be explained by the variation in trichome density. None of the aphid samples contained Bt protein. As a consequence, natural enemies that feed on aphids are not exposed to the Cry protein. A significant difference in the sugar composition of aphid honeydew was detected among cotton varieties as well as between transformed and non-transformed plants. However, it is questionable if this variation is of ecological relevance, especially as honeydew is not the only sugar source parasitoids feed on in cotton fields. Our study allows the conclusion that Bt cotton poses a negligible risk for aphid antagonists and that aphids should remain under natural control in Bt cotton fields.

  15. Early warning of cotton bollworm resistance associated with intensive planting of Bt cotton in China.

    Directory of Open Access Journals (Sweden)

    Haonan Zhang

    Full Text Available Transgenic crops producing Bacillus thuringiensis (Bt toxins kill some key insect pests, but evolution of resistance by pests can reduce their efficacy. The predominant strategy for delaying pest resistance to Bt crops requires refuges of non-Bt host plants to promote survival of susceptible pests. To delay pest resistance to transgenic cotton producing Bt toxin Cry1Ac, farmers in the United States and Australia planted refuges of non-Bt cotton, while farmers in China have relied on "natural" refuges of non-Bt host plants other than cotton. Here we report data from a 2010 survey showing field-evolved resistance to Cry1Ac of the major target pest, cotton bollworm (Helicoverpa armigera, in northern China. Laboratory bioassay results show that susceptibility to Cry1Ac was significantly lower in 13 field populations from northern China, where Bt cotton has been planted intensively, than in two populations from sites in northwestern China where exposure to Bt cotton has been limited. Susceptibility to Bt toxin Cry2Ab did not differ between northern and northwestern China, demonstrating that resistance to Cry1Ac did not cause cross-resistance to Cry2Ab, and implying that resistance to Cry1Ac in northern China is a specific adaptation caused by exposure to this toxin in Bt cotton. Despite the resistance detected in laboratory bioassays, control failures of Bt cotton have not been reported in China. This early warning may spur proactive countermeasures, including a switch to transgenic cotton producing two or more toxins distinct from Cry1A toxins.

  16. Induced mutations for improvement of desi cotton

    International Nuclear Information System (INIS)

    Waghmare, V.N.; Mohan, Punit; Singh, Phundan; Gururajan, K.N.

    2000-01-01

    Desi cotton varieties of Gossypium arboreum have wide adaptability and are relatively tolerant to biotic (insect pests and diseases) and abiotic (moisture and salt) stresses. Desi varieties have got potential to yield even under adverse and low input situations. Most of them are synchronous in maturity and possess consistent fibre properties. Despite such merits, very little attention has been paid for improvement of desi cotton. The present area under arboreum varieties is 17.0% (15.30 lakh ha.) against 65% (35.75 lakh ha) during 1947-48. Deliberate attempts are required to improve G. arboreum for its economic and quality characters to compete with upland varieties in rainfed cotton ecology

  17. Biological control of cotton aphid (Aphis gossypii Glover) in cotton (inter)cropping systems in China : a simulation study

    NARCIS (Netherlands)

    Xia, J.

    1997-01-01

    Cotton aphid ( Aphis gossypii Glover) is the key insect pest of seedling cotton ( Gossypium hirsutum L. ) in China, particularly in the North China cotton region. The resulting annual losses amount to 10-15% of the attainable yield. Sole reliance on

  18. Diversity of arthropod community in transgenic poplar-cotton ecosystems.

    Science.gov (United States)

    Zhang, D J; Lu, Z Y; Liu, J X; Li, C L; Yang, M S

    2015-12-02

    Poplar-cotton agro-ecosystems are the main agricultural planting modes of plain cotton fields in China. Here, we performed a systematic survey of the diversity and population of arthropod communities in four different combination of poplar-cotton eco-systems, including I) non-transgenic poplar and non-transgenic cotton fields; II) non-transgenic poplar and transgenic cotton fields [Bacillus thuringiensis (Bt) cotton]; III) Bt transgenic poplar (high insect resistant strain Pb29) and non-transgenic cotton; and IV) transgenic poplar and transgenic cotton fields, over a period of 3 years. Based on the statistical methods used to investigate community ecology, the effects of transgenic ecosystems on the whole structure of the arthropod community, on the structure of arthropods in the nutritive layer, and on the similarity of arthropod communities were evaluated. The main results were as follows: the transgenic poplar-cotton ecosystem has a stronger inhibitory effect on insect pests and has no impact on the structure of the arthropod community, and therefore, maintains the diversity of the arthropod community. The character index of the community indicated that the structure of the arthropod community of the transgenic poplar-cotton ecosystem was better than that of the poplar-cotton ecosystem, and that system IV had the best structure. As for the abundance of nutritional classes, the transgenic poplar-cotton ecosystem was also better than that of the non-transgenic poplar-cotton ecosystem. The cluster analysis and similarity of arthropod communities between the four different transgenic poplar-cotton ecosystems illustrated that the structure of the arthropod community excelled in the small sample of the transgenic poplar-cotton ecosystems.

  19. Radiation degradation of short-cotton linters

    International Nuclear Information System (INIS)

    Ma Zue Teh; Zhou Rui Min

    1984-01-01

    Radiation degradation of short-cotton linters has been studied by using X-ray diffraction, an infrared spectrometer and a viscosimeter. Average molecular weight and crystallinity of short-cotton linters and the change of reducing sugar in γ-radiation degradation were examined. It was found that cellulosic saccharification in hydrolysis was enhanced with preirradiation of linter. This probably resulted from the radiation induced change of cellulosic structure. Sensitizers to promote radiation degradation effect were investigated. Carbon tetrachloride has been found to be effective. (author)

  20. Identification of Marker-Trait Associations for Lint Traits in Cotton

    Science.gov (United States)

    Iqbal, Muhammad A.; Rahman, Mehboob-ur-

    2017-01-01

    Harvesting high quality lint, a long-awaited breeding goal—accomplished partly, can be achieved by identifying DNA markers which could be used for diagnosing cotton plants containing the desired traits. In the present studies, a total of 185 cotton genotypes exhibiting diversity for lint traits were selected from a set of 546 genotypes evaluated for fiber traits in 2009. These genotypes were extensively studied for three consecutive years (2011–2013) at three different locations. Significant genetic variations were found for average boll weight, ginning out turn (GOT), micronaire value, staple length, fiber bundle strength, and uniformity index. IR-NIBGE-3701 showed maximum GOT (43.63%). Clustering of genotypes using Ward's method was found more informative than that of the clusters generated by principal component analysis. A total of 382 SSRs were surveyed on 10 Gossypium hirsutum genotypes exhibiting contrasting fiber traits. Out of these, 95 polymorphic SSR primer pairs were then surveyed on 185 genotypes. The gene diversity averaged 0.191 and the polymorphic information content (PIC) averaged 0.175. Unweighted pair group method with arithmetic mean (UPGMA), principal coordinate analysis (PCoA), and STRUCTURE software grouped these genotypes into four major clusters each. Genetic distance within the clusters ranged from 0.0587 to 0.1030. A total of 47 (25.41%) genotypes exhibited shared ancestry. In total 6.8% (r2 ≥ 0.05) and 4.4% (r2 ≥ 0.1) of the marker pairs showed significant linkage disequilibrium (LD). A number of marker-trait associations (in total 75) including 13 for average boll weight, 18 for GOT percentage, eight for micronaire value, 18 for staple length, three for fiber bundle strength, and 15 for uniformity index were calculated. Out of these, MGHES-51 was associated with all the traits. Most of the marker-trait associations were novel while few validated the associations reported in the previous studies. High frequency of favorable

  1. Detecting mismatches in the phenology of cotton bollworm larvae and cotton flowering in response to climate change

    Science.gov (United States)

    Huang, Jian; Hao, HongFei

    2018-05-01

    Current evidence suggests that climate change has directly affected the phenology of many invertebrate species associated with agriculture. Such changes in phenology have the potential to cause temporal mismatches between predators and prey and may lead to a disruption in natural pest control ecosystem. Understanding the synchrony between pest insects and host plant responses to climate change is a key step to improve integrated pest management strategies. Cotton bollworm larvae damage cotton, and thus, data from Magaiti County, China, collected during the period of 1990-2015 were analyzed to assess the effects of climate change on cotton bollworm larvae and cotton flowering. The results showed that a warming climate advanced the phenology of cotton bollworm larvae and cotton flowering. However, the phenological rate of change was faster in cotton bollworm larvae than that in cotton flowering, and the larval period was prolonged, resulting in a great increase of the larval population. The abrupt phenological changes in cotton bollworm larvae occurred earlier than that in cotton, and the abrupt phenological changes in cotton flowering occurred earlier than that in larval abundance. However, the timing of abrupt changes in larval abundance all occurred later than that in temperature. Thus, the abrupt changes that occurred in larvae, cotton flowering and climate were asynchronous. The interval days between the cotton flowering date (CFD) and the half-amount larvae date (HLD) expanded by 3.41 and 4.41 days with a 1 °C increase of T mean in May and June, respectively. The asynchrony between cotton bollworm larvae and cotton flowering will likely broaden as the climate changes. The effective temperature in March and April and the end date of larvae (ED) were the primary factors affecting asynchrony.

  2. Detecting mismatches in the phenology of cotton bollworm larvae and cotton flowering in response to climate change.

    Science.gov (United States)

    Huang, Jian; Hao, HongFei

    2018-05-11

    Current evidence suggests that climate change has directly affected the phenology of many invertebrate species associated with agriculture. Such changes in phenology have the potential to cause temporal mismatches between predators and prey and may lead to a disruption in natural pest control ecosystem. Understanding the synchrony between pest insects and host plant responses to climate change is a key step to improve integrated pest management strategies. Cotton bollworm larvae damage cotton, and thus, data from Magaiti County, China, collected during the period of 1990-2015 were analyzed to assess the effects of climate change on cotton bollworm larvae and cotton flowering. The results showed that a warming climate advanced the phenology of cotton bollworm larvae and cotton flowering. However, the phenological rate of change was faster in cotton bollworm larvae than that in cotton flowering, and the larval period was prolonged, resulting in a great increase of the larval population. The abrupt phenological changes in cotton bollworm larvae occurred earlier than that in cotton, and the abrupt phenological changes in cotton flowering occurred earlier than that in larval abundance. However, the timing of abrupt changes in larval abundance all occurred later than that in temperature. Thus, the abrupt changes that occurred in larvae, cotton flowering and climate were asynchronous. The interval days between the cotton flowering date (CFD) and the half-amount larvae date (HLD) expanded by 3.41 and 4.41 days with a 1 °C increase of T mean in May and June, respectively. The asynchrony between cotton bollworm larvae and cotton flowering will likely broaden as the climate changes. The effective temperature in March and April and the end date of larvae (ED) were the primary factors affecting asynchrony.

  3. Give Earth a Chance Series, Dirty Air, Trash Is Taking Over, Sounds and Silence, Pesticides Are Perilous, Tragedy in the Laundromat, Troublesome Tail Pipes.

    Science.gov (United States)

    Minneapolis Independent School District 275, Minn.

    These six booklets in the "Give Earth a Chance Series" are titled, "Dirty Air,""Trash is Taking Over,""Sounds and Silence,""Pesticides are Perilous,""Tragedy in the Laundromat," and "Troublesome Tail Pipes." The booklets are suitable for elementary use, and are intended to…

  4. 7 CFR 1427.101 - Eligible upland cotton.

    Science.gov (United States)

    2010-01-01

    ... classification purposes that have been rebaled; (3) Semi-processed motes that are of a quality suitable, without further processing, for spinning, papermaking, or production of non-woven fabric; or (4) Re-ginned... derivatives of the lint cleaning process; or (3) Textile mill wastes. ...

  5. Influence of Tencel/cotton blends on knitted fabric performance

    Directory of Open Access Journals (Sweden)

    Alaa Arafa Badr

    2016-09-01

    Full Text Available The requirements in terms of wearing comfort with sportswear, underwear and outerwear are widely linked to the use of new fibers. Today, Tencel fiber is one of the most important developments in regenerated cellulosic fiber. However, the relation between Tencel fiber properties and fabric characteristics has not been enough studied in the literature especially the influence of fiber materials on mechanical, Ultraviolet Protection Factor (UPF and absorption properties. Therefore, in this study, knitted fabric samples were manufactured with eight different yarns with two fabric types (single jersey and single jersey with Lycra. 30/1-Ne yarns from natural and regenerated cellulosic fibers: 50% Tencel-LF/50% cotton, 67% Tencel-LF/33% cotton, 67% Tencel-STD/33% cotton, 70% bamboo/30% cotton, 100% bamboo, 100% Modal, 100% Micro-Modal and 100% cotton were employed. Then, all the produced fabrics were subjected to five cycles laundering and then flat dried. The results show that 67% Tencel-LF/33% cotton has more flexural rigidity and withdrawing handle force than 67% Tencel-STD/33% cotton fabric, while 67% Tencel-STD/33% cotton has a merit of durability during bursting test. Blending Egyptian cotton fibers with bamboo and Tencel as in 70/30% bamboo/cotton and 50/50% Tencel-LF/cotton improve UPF of the produced fabric.

  6. Gene cloning: exploring cotton functional genomics and genetic improvement

    Institute of Scientific and Technical Information of China (English)

    Diqiu LIU; Xianlong ZHANG

    2008-01-01

    Cotton is the most important natural fiber plant in the world. The genetic improvement of the quality of the cotton fiber and agricultural productivity is imperative under the situation of increasing consumption and rapid development of textile technology. Recently, the study of cotton molecular biology has progressed greatly. A lot of specifically or preferentially expressed cotton fiber genes were cloned and analyzed. On the other hand, identification of stress response genes expressed in cotton was performed by other research groups. The major stress factors were studied including the wilt pathogens Verticillium dahliae, Fusarium oxy-sporum f. sp. vasinfectum, bacterial blight, root-knot nematode, drought, and salt stress. What is more, a few genes related to the biosynthesis of gossypol, other sesquiterpene phytoalexins and the major seed oil fatty acids were isolated from cotton. In the present review, we focused on the major advances in cotton gene cloning and expression profiling in the recent years.

  7. The Impacts of U.S. Cotton Programs on the West and Central African Countries Cotton Export Earnings

    OpenAIRE

    Fadiga, Mohamadou L.; Mohanty, Samarendu; Pan, Suwen

    2005-01-01

    This study uses a stochastic simulation approach based on a partial equilibrium structural econometric model of the world fiber market to examine the effects of a removal of U.S. cotton programs on the world market. The effects on world cotton prices and African export earnings were analyzed. The results suggest that on average an elimination of U.S. cotton programs would lead to a marginal increase in the world cotton prices thus resulting in minimal gain for cotton exporting countries in Af...

  8. Effects of rotation of cotton (Gossypium hirsutum L.) and soybean [Glycine max (L.) Merr.] crops on soil fertility in Elizabeth, Mississippi, USA

    OpenAIRE

    H.A., Reddy, K. and Pettigrew, W.T.

    2018-01-01

    The effects of cotton (Gossypium hirsutum L.): soybean [Glycine max (L.) Merr.] rotation on the soil fertility levels are limited. An irrigated soybean: cotton rotation experiment was conducted from 2012 through 2015 near Elizabeth, Mississippi, USA. The crop rotation sequences were included continuous cotton (CCCC), continuous soybean (SSSS), cotton-soybean-cotton-soybean (CSCS), cotton-soybean-soybean-cotton (CSSC), soybean-cotton-cotton-soybean (SCCS), soybean-cotton-soybean-cotton (SCSC)....

  9. Pilot plant studies of the bioconversion of cellulose and production of ethanol

    Energy Technology Data Exchange (ETDEWEB)

    Wilke, C.R.

    1977-01-31

    Progress is reported in several areas of research. The following cellulosic raw materials were selected for study: wheat, barley, and rice straws, rice hulls, sorghum, corn stover, cotton gin trash, newsprint, ground wood, and masonite steam-treated Douglas fir and redwood. Samples were collected, prepared, and analyzed for hexosans, pentosans, lignin, ash, and protein. Results of acid extraction and enzymatic hydrolysis are discussed. Yields of glucose, polyglucose, xylose, and arabinose are reported. Progress in process design and economic studies, as well as pilot plant process development and design studies, is summarized. (JGB)

  10. Evaluating cotton seed gland initiation by microscopy

    Science.gov (United States)

    Gossypol is a terpenoid aldehyde found in cotton (Gossypium hirsutum L.) glands and helps protect the seed from pests and pathogens. However, gossypol is toxic to many animals, so the seed is used mainly in cattle feed, as ruminants are tolerant to the effects of gossypol. In order to develop strat...

  11. Satellite-based monitoring of cotton evapotranspiration

    Science.gov (United States)

    Dalezios, Nicolas; Dercas, Nicholas; Tarquis, Ana Maria

    2016-04-01

    Water for agricultural use represents the largest share among all water uses. Vulnerability in agriculture is influenced, among others, by extended periods of water shortage in regions exposed to droughts. Advanced technological approaches and methodologies, including remote sensing, are increasingly incorporated for the assessment of irrigation water requirements. In this paper, remote sensing techniques are integrated for the estimation and monitoring of crop evapotranspiration ETc. The study area is Thessaly central Greece, which is a drought-prone agricultural region. Cotton fields in a small agricultural sub-catchment in Thessaly are used as an experimental site. Daily meteorological data and weekly field data are recorded throughout seven (2004-2010) growing seasons for the computation of reference evapotranspiration ETo, crop coefficient Kc and cotton crop ETc based on conventional data. Satellite data (Landsat TM) for the corresponding period are processed to estimate cotton crop coefficient Kc and cotton crop ETc and delineate its spatiotemporal variability. The methodology is applied for monitoring Kc and ETc during the growing season in the selected sub-catchment. Several error statistics are used showing very good agreement with ground-truth observations.

  12. Airborne multispectral detection of regrowth cotton fields

    Science.gov (United States)

    Regrowth of cotton, Gossypium hirsutum L., can provide boll weevils, Anthonomus grandis Boheman, with an extended opportunity to feed and reproduce beyond the production season. Effective methods for timely areawide detection of these potential host plants are critically needed to achieve eradicati...

  13. Integrated nutrients management for 'desi' cotton

    International Nuclear Information System (INIS)

    Qazi, M.A.; Akram, M.; Ahmad, N.; Khattak, M.A.

    2007-01-01

    Intensive cropping with no return of crop residues and other organic inputs result in the loss of soil organic matter (SOM) and nutrient supply in (Desi) cotton-wheat cropping system in Pakistan. For appraisal of problem and finding solution to sustainability, we evaluated six treatments comprised of two fertilizer doses and three management techniques over a period of three years (2003-05) monitoring their effects on seed cotton yield and soil fertility. The techniques included chemical fertilizers, municipal solid waste manure (MSWM) integrated with chemical fertilizers in 1:4 ratios with, and without pesticides. The results revealed that cotton yields. Were enhanced by 19% due to site-specific fertilizer dose over conventional dose. Ignoring weeds control by means of herbicided application resulted in 5% decrease of seed cotton yield in IPNM technique positive effect of MSWM integration was noted on soil test phosphorus and SOM. Site-specific fertilizer application and integrated plant nutrient management by MSWM proved their suitability as the techniques not only improve soil quality in terms of sustained levels of organic matter and phosphorus but also provide a safe way of waste disposal. (author)

  14. Cotton genetic resources and crop vulnerability

    Science.gov (United States)

    A report on the genetic vulnerability of cotton was provided to the National Genetic Resources Advisory Council. The report discussed crop vulnerabilities associated with emerging diseases, emerging pests, and a narrowing genetic base. To address these crop vulnerabilities, the report discussed the ...

  15. PESTICIDE CONTAMINATION OF THE DRIDJI COTTON ...

    African Journals Online (AJOL)

    ruud

    pesticide contamination in the Dridji cotton production area poses a risk to public ... the Kiti River as well as bean leaves grown near the river were sampled and ... Sediments were analysed at the Institute of Environmental Studies of the VU .... Empty bottles of pesticides were recycled to buy oil from the market and to bring.

  16. Locally Grown: Examining Attitudes and Perceptions About Organic Cotton Production and Manufacturing Between Mississippi Cotton Growers and Consumers

    Directory of Open Access Journals (Sweden)

    Charles Freeman

    2016-06-01

    Full Text Available The purpose of this study is to examine attitudes and perceptions about organic cotton of Mississippi cotton growers and producers in comparison to fashion-conscious consumers, including advantages/disadvantages of growing and production processes, quality control, consumer preferences, and competitive price structures/profit margins. A sample size of 16 local Mississippi growers and/or producers and 44 undergraduate students at a mid-major Southeastern university were chosen to participate in the study. Instruments were developed based on current research and the definition of organic cotton production defined by the United States Department of Agriculture. Results indicate 75% of growers and producers do not perceive a quality difference between organic and conventionally grown cotton, while 72.7% of the consumers report organically grown cotton is capable of producing a higher quality product compared to conventionally grown cotton. Even with an increase in organic cotton prices (25- 40% higher premium, only 25% of growers and producers would be willing to convert, while a majority (52.3% of consumers would not be willing to spend more than 25% extra for an organically grown cotton product. Consumers indicate the negative effects of conventionally grown cotton, yet many report little knowledge about organic cotton production, while growers/producers immediately dismiss organically grown cotton as a retail marketing strategy.

  17. The halo effect: suppression of pink bollworm on non-Bt cotton by Bt cotton in China.

    Directory of Open Access Journals (Sweden)

    Peng Wan

    Full Text Available In some previously reported cases, transgenic crops producing insecticidal proteins from Bacillus thuringiensis (Bt have suppressed insect pests not only in fields planted with such crops, but also regionally on host plants that do not produce Bt toxins. Here we used 16 years of field data to determine if Bt cotton caused this "halo effect" against pink bollworm (Pectinophora gossypiella in six provinces of the Yangtze River Valley of China. In this region, the percentage of cotton hectares planted with Bt cotton increased from 9% in 2000 to 94% in 2009 and 2010. We found that Bt cotton significantly decreased the population density of pink bollworm on non-Bt cotton, with net decreases of 91% for eggs and 95% for larvae on non-Bt cotton after 11 years of Bt cotton use. Insecticide sprays targeting pink bollworm and cotton bollworm (Helicoverpa armigera decreased by 69%. Previously reported evidence of the early stages of evolution of pink bollworm resistance to Bt cotton in China has raised concerns that if unchecked, such resistance could eventually diminish or eliminate the benefits of Bt cotton. The results reported here suggest that it might be possible to find a percentage of Bt cotton lower than the current level that causes sufficient regional pest suppression and reduces the risk of resistance.

  18. Reflexões sobre o trabalho do psicólogo do esporte em uma academia de ginástica

    Directory of Open Access Journals (Sweden)

    Livia Gomes Viana-Meireles

    2015-11-01

    Full Text Available http://dx.doi.org/10.5007/2175-8042.2015v27n46p171 O presente estudo buscou desenvolver uma reflexão sobre a prática do psicólogo do esporte dentro de uma academia de ginástica a partir do relato de experiência de estágio em psicologia. Foi realizada uma pesquisa com alunos e professores que possibilitou a contextualização do ambiente da academia e o planejamento das atividades a serem realizadas. A experiência de estágio possibilitou o início de uma reflexão sobre o campo de atuação do psicólogo do esporte nas academias de ginástica apontando ricas possibilidades para ações e intervenções em diferentes contextos que envolvam atividade física.

  19. Resilient modulus of black cotton soil

    Directory of Open Access Journals (Sweden)

    K.H. Mamatha

    2017-03-01

    Full Text Available Resilient modulus (MR values of pavement layers are the basic input parameters for the design of pavements with multiple layers in the current mechanistic empirical pavement design guidelines. As the laboratory determination of resilient modulus is costly, time consuming and cumbersome, several empirical models are developed for the prediction of resilient modulus for different regions of the world based on the database of resilient modulus values of local soils. For use of these relationships there is a need to verify the suitability of these models for local conditions. Expansive clay called black cotton soil (BC soil is found in several parts of India and is characterized by low strength and high compressibility. This soil shows swell – shrink behaviour upon wetting and drying and are problematic. The BC soil shows collapse behaviour on soaking and therefore the strength of the soil needs to be improved. Additive stabilization is found to be very effective in stabilizing black cotton soils and generally lime is used to improve the strength and durability of the black cotton soil. In this paper, the results of repeated load tests on black cotton soil samples for the determination of MR under soaked and unsoaked conditions at a relative compaction levels of 100% and 95% of both standard and modified proctor conditions are reported. The results indicate that the black cotton soil fails to meet the density requirement of the subgrade soil and shows collapse behaviour under soaked condition. To overcome this, lime is added as an additive to improve the strength of black cotton soil and repeated load tests were performed as per AASHTO T 307 - 99 for MR determination. The results have shown that the samples are stable under modified proctor condition with MR values ranging from 36 MPa to 388 MPa for a lime content of 2.5% and curing period ranging from 7 to 28 days. Also, it is observed that, the CBR based resilient modulus is not in agreement

  20. Production cross sections and isomeric ratios for sup(110m)In/sup(110g)In formed in Cd (d,xn) reactions

    International Nuclear Information System (INIS)

    Herreros Usher, Oscar; Maceiras de Jefimowicz, Elena; De la Vega Vedoya, Mario; Jorge Nassiff, Sonia

    1980-01-01

    Excitation functions and isomeric cross sections ratios have been measured for the 110 Cd (d,2n) and 111 Cd (d,3n) reactions in which the isomeric pair sup(110m)In/sup(110g)In is produced. Activation method was employed and the irradiations were performed at the synchrocyclotron of the Comision Nacional de Energia Atomica, Argentina, with an incident energy of 27.MeV. (author) [es

  1. Effects of nematicides on cotton root mycobiota.

    Science.gov (United States)

    Baird, R E; Carling, D E; Watson, C E; Scruggs, M L; Hightower, P

    2004-02-01

    Baseline information on the diversity and population densities of fungi collected from soil debris and cotton (Gossypium hirsutum L.) roots was determined. Samples were collected from Tifton, GA, and Starkville, MS containing cotton field soil treated with the nematicides 1,3-dichloroproprene (fumigant) and aldicarb (granules). A total of 10,550 and 13,450 fungal isolates were collected from these two study sites, respectively. Of this total, 34 genera of plant pathogenic or saprophytic species were identified. Pathogenic root fungi included Fusarium spp. (40% of all isolations), Macrophomina, Pythium, Rhizoctonia, and Sclerotium. Fusarium and Rhizoctonia were the most common fungal species identified and included F. oxysporum, F. verticillioides and F. solani, the three Fusarium species pathogenic on cotton plants. Population densities of Fusarium were not significantly different among locations or tissue types sampled. Macrophomina was isolated at greater numbers near the end of the growing seasons. Anastomosis groups of R. solani isolated from roots and soil debris included AG-3, -4, -7, 2-2, and -13 and anastomosis groups of binucleate Rhizoctonia included CAG-2, -3, and -5. Occurrences and frequency of isolations among sampling dates were not consistent. Fluctuations in the frequency of isolation of Rhizoctonia did not correspond with changes in frequency of isolation of the biological control fungus, Trichoderma. When individual or pooled frequencies of the mycobiota were compared to nematicide treatments, no specific trends occurred between treatments, application methods or rates. Results from this study show that use of 1,3-D and aldicarb in cotton fields does not significantly impact plant pathogenic fungi or saprophytic fungal populations. Thus cotton producers need not adjust seedling disease control measures when these two nematicides are used.

  2. Processing and properties of PCL/cotton linter compounds

    Energy Technology Data Exchange (ETDEWEB)

    Bezerra, Elieber Barros; Franca, Danyelle Campos; Morais, Dayanne Diniz de Souza; Araujo, Edcleide Maria [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Departamento de Engenharia de Materiais; Rosa, Morsyleide de Freitas; Morais, Joao Paulo Saraiva [Embrapa Tropical Agroindustia, Fortaleza, CE (Brazil); Wellen, Renate Maria Ramos, E-mail: wellen.renate@gmail.com [Universidade Federal da Paraiaba (UFPB), Joao Pessoa, PB (Brazil)

    2017-03-15

    Biodegradable compounds of poly(ε-caprolactone) (PCL)/ cotton linter were melting mixed with filling content ranging from 1% to 5% w/w. Cotton linter is an important byproduct of textile industry; in this work it was used in raw state and after acid hydrolysis. According to the results of torque rheometry no decaying of viscosity took place during compounding, evidencing absence of breaking down in molecular weight. The thermal stability increased by 20% as observed in HDT for PCL/cotton nanolinter compounds. Adding cotton linter to PCL did not change its crystalline character as showed by XRD; however an increase in degree of crystallinity was observed by means of DSC. From mechanical tests in tension was observed an increase in ductility of PCL, and from mechanical tests in flexion an increase in elastic modulus upon addition of cotton linter, whereas impact strength presented lower values for PCL/cotton linter and PCL/cotton nanolinter compounds. SEM images showed that PCL presents plastic fracture and cotton linter has an interlacing fibril structure with high L/D ratio, which are in agreement with matrix/fibril morphology observed for PCL/cotton linter compounds. PCL/cotton linter compounds made in this work cost less than neat PCL matrix and presented improved properties making feasible its commercial use. (author)

  3. Cover Crop Biomass Harvest Influences Cotton Nitrogen Utilization and Productivity

    Directory of Open Access Journals (Sweden)

    F. Ducamp

    2012-01-01

    Full Text Available There is a potential in the southeastern US to harvest winter cover crops from cotton (Gossypium hirsutum L. fields for biofuels or animal feed use, but this could impact yields and nitrogen (N fertilizer response. An experiment was established to examine rye (Secale cereale L. residue management (RM and N rates on cotton productivity. Three RM treatments (no winter cover crop (NC, residue removed (REM and residue retained (RET and four N rates for cotton were studied. Cotton population, leaf and plant N concentration, cotton biomass and N uptake at first square, and cotton biomass production between first square and cutout were higher for RET, followed by REM and NC. However, leaf N concentration at early bloom and N concentration in the cotton biomass between first square and cutout were higher for NC, followed by REM and RET. Seed cotton yield response to N interacted with year and RM, but yields were greater with RET followed by REM both years. These results indicate that a rye cover crop can be beneficial for cotton, especially during hot and dry years. Long-term studies would be required to completely understand the effect of rye residue harvest on cotton production under conservation tillage.

  4. Engineered disease resistance in cotton using RNA-interference to knock down cotton leaf curl kokhran virus-Burewala and cotton leaf curl Multan betasatellite

    Science.gov (United States)

    Cotton Leaf Curl virus Disease (CLCuD) has caused enormous losses in cotton (Gossypium hirsutum) production in Pakistan. RNA interference (RNAi) is an emerging technique that could knock out CLCuD by targeting different regions of the pathogen genome that are important for replication, transcription...

  5. Motivos de abandono na prática de ginástica artística no contexto extracurricular

    Directory of Open Access Journals (Sweden)

    Priscila LOPES

    Full Text Available Resumo O Esporte consiste na principal opção para a prática de atividades físicas entre as crianças e os jovens. Apesar do grande interesse desse público às práticas esportivas, a literatura aponta alto índice de abandono. Motivados por essa conjuntura, o objetivo desse estudo foi verificar o motivo de abandono, mais especificamente, na prática de Ginástica Artística (GA no contexto das atividades extracurriculares. Entrevistamos praticantes meninas de GA que apresentavam histórico de abandono dessa prática esportiva por determinado período de tempo. Para o tratamento dos dados, optamos pela Análise de Conteúdo proposta por BARDIN. Constatamos que fatores intrínsecos e extrínsecos estão vinculados ao processo de abandono da prática desse esporte. Entretanto, os fatores extrínsecos sobrepuseram àqueles intrínsecos, o que evidencia que o ambiente e as condições situacionais e interpessoais exercem maior influência sobre o afastamento das ginastas. Assim, ressaltamos a importância da atenção dos profissionais a esses aspectos para garantir que as atividades atendam às necessidades e aos anseios das ginastas.

  6. 75 FR 70850 - Common Crop Insurance Regulations; Extra Long Staple Cotton Crop Provisions

    Science.gov (United States)

    2010-11-19

    ... dividing Price A by 85 percent of Price B. * * * * * (f) Any AUP cotton harvested or appraised from acreage... dividing the price per pound for AUP cotton by the price per pound for ELS cotton. The prices used for AUP...

  7. 77 FR 51867 - Cotton Board Rules and Regulations: Adjusting Supplemental Assessment on Imports

    Science.gov (United States)

    2012-08-28

    ... Advertising, Agricultural research, Cotton, Marketing agreements, Reporting and recordkeeping requirements... supplemental assessments collected for use by the Cotton Research and Promotion Program. An amendment is..., Chief, Research and Promotion Staff, Cotton and Tobacco Programs, AMS, USDA, 100 Riverside Parkway...

  8. Modern trends on development of cotton production and processing chain Uzbekistan

    OpenAIRE

    Abdimumin Alikulov

    2010-01-01

    The cotton production complex of Uzbekistan has high rating comparing other export oriented branches. Cotton fiber value in 2008 share made 12% from total export of the country. The paper observes some trends and policy developments in cotton industry development.

  9. Regulation of auxin on secondary cell wall cellulose biosynthesis in developing cotton fibers

    Science.gov (United States)

    Cotton (Gossypium hirsutum L.) fibers are unicellular trichomes that differentiate from epidermal cells of developing cotton ovules. Mature fibers exhibit thickened secondary walls composed of nearly pure cellulose. Cotton fiber development is divided into four overlapping phases, 1) initiation sta...

  10. Fabrication of cotton fabric with superhydrophobicity and flame retardancy.

    Science.gov (United States)

    Zhang, Ming; Wang, Chengyu

    2013-07-25

    A simple and facile method for fabricating the cotton fabric with superhydrophobicity and flame retardancy is described in the present work. The cotton fabric with the maximal WCA of 160° has been prepared by the covalent deposition of amino-silica nanospheres and the further graft with (heptadecafluoro-1,1,2,2-tetradecyl) trimethoxysilane. The geometric microstructure of silica spheres was measured by transmission electron microscopy (TEM). The cotton textiles before and after treatment were characterized by using scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). The wetting behavior of cotton samples was investigated by water contact angle measurement. Moreover, diverse performances of superhydrophobic cotton textiles have been evaluated as well. The results exhibited the outstanding superhydrophobicity, excellent waterproofing durability and flame retardancy of the cotton fabric after treatment, offering a good opportunity to accelerate the large-scale production of superhydrophobic textiles materials for new industrial applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

  11. An Assessment of Current Policy Initiatives in Zambia's Cotton Sector

    OpenAIRE

    Zulu, Ballard; Tschirley, David L.

    2004-01-01

    This paper assesses three of these policy initiatives: input credit provision for smallholder producers of selected cash crops including cotton, the proposed creation of a Cotton Board, and the emergence in 2003 of District Council levies as a point of conflict between local governments and cotton companies. The purpose of the paper is to provide guidance to public and private decision makers regarding key modifications which may need to be made to these policies to ensure continued healthy d...

  12. Processing and Properties of PCL/Cotton Linter Compounds

    OpenAIRE

    Bezerra,Elieber Barros; França,Danyelle Campos; Morais,Dayanne Diniz de Souza; Rosa,Morsyleide de Freitas; Morais,João Paulo Saraiva; Araújo,Edcleide Maria; Wellen,Renate Maria Ramos

    2017-01-01

    Biodegradable compounds of poly(ε-caprolactone) (PCL)/ cotton linter were melting mixed with filling content ranging from 1% to 5% w/w. Cotton linter is an important byproduct of textile industry; in this work it was used in raw state and after acid hydrolysis. According to the results of torque rheometry no decaying of viscosity took place during compounding, evidencing absence of breaking down in molecular weight. The thermal stability increased by 20% as observed in HDT for PCL/cotton...

  13. THE WORLD TRADE ORGANIZATION AND SOUTHERN AGRICULTURE: THE COTTON PERSPECTIVE

    OpenAIRE

    Hudson, Darren

    2000-01-01

    The World Trade Organization (WTO) negotiations could have important implications for Southern Agriculture. This paper explores some of the issues surrounding the WTO negotiations for cotton. Specifically, this paper examines the impacts of the phase-out of the Multi-Fiber Arrangement (MFA) on the location of textile production and cotton trade flows. Generally, it is believed that the WTO negotiations will have little direct impact on cotton, but will have indirect impacts through textile po...

  14. EVALUATION OF FOUR INTEGRATED PEST MANAGEMENT PACKAGES FOR CONTROLLING MAIN PESTS OF COTTON IN RAINFED FIELDS

    OpenAIRE

    Nurindah Nurindah; Dwi Adi Sunarto

    2014-01-01

    Cotton production nationally is low due to various constraints, including pests. Two main pests commonly found in cotton plantation in rain fed fields are cotton leafhopper (Amrasca biguttula) and cotton bollworm (Helicoverpa armigera). The study aimed to evaluate four packages of integrated pest management (IPM) techniques to control cotton leafhopper and cotton bollworm in rain fed fields. The experiment was conducted in farmers’ fields at Asembagus, East Java, between January and July 2012...

  15. Screening Pakistani cotton for drought tolerance

    International Nuclear Information System (INIS)

    Soomro, M.H.; Markhand, G.S.

    2011-01-01

    The drought is one of the biggest abiotic stresses for crop production in arid and semi-arid agriculture. Thus it is a challenge for plant scientists to screen and develop the drought tolerant cotton lines. In this study, 31 cotton genotypes/cultivars were evaluated under two irrigation regimes i. e., seven irrigations (Control) and two irrigations (Stress), using split plot design with four replications. The crop growth, yield and some physiological parameters were studied. There were high inter-varietal differences for all the parameters under control as well as drought stress. Although all the varieties for all parameters were significantly affected by drought but however, CRIS-9, MARVI, CRIS-134, CRIS-126, CRIS-337, CRIS-355 and CRIS-377 maintained highest performance for all the parameters studied under high drought conditions. (author)

  16. Cotton genotypes selection through artificial neural networks.

    Science.gov (United States)

    Júnior, E G Silva; Cardoso, D B O; Reis, M C; Nascimento, A F O; Bortolin, D I; Martins, M R; Sousa, L B

    2017-09-27

    Breeding programs currently use statistical analysis to assist in the identification of superior genotypes at various stages of a cultivar's development. Differently from these analyses, the computational intelligence approach has been little explored in genetic improvement of cotton. Thus, this study was carried out with the objective of presenting the use of artificial neural networks as auxiliary tools in the improvement of the cotton to improve fiber quality. To demonstrate the applicability of this approach, this research was carried out using the evaluation data of 40 genotypes. In order to classify the genotypes for fiber quality, the artificial neural networks were trained with replicate data of 20 genotypes of cotton evaluated in the harvests of 2013/14 and 2014/15, regarding fiber length, uniformity of length, fiber strength, micronaire index, elongation, short fiber index, maturity index, reflectance degree, and fiber quality index. This quality index was estimated by means of a weighted average on the determined score (1 to 5) of each characteristic of the HVI evaluated, according to its industry standards. The artificial neural networks presented a high capacity of correct classification of the 20 selected genotypes based on the fiber quality index, so that when using fiber length associated with the short fiber index, fiber maturation, and micronaire index, the artificial neural networks presented better results than using only fiber length and previous associations. It was also observed that to submit data of means of new genotypes to the neural networks trained with data of repetition, provides better results of classification of the genotypes. When observing the results obtained in the present study, it was verified that the artificial neural networks present great potential to be used in the different stages of a genetic improvement program of the cotton, aiming at the improvement of the fiber quality of the future cultivars.

  17. Ecoinformatics reveals effects of crop rotational histories on cotton yield.

    Science.gov (United States)

    Meisner, Matthew H; Rosenheim, Jay A

    2014-01-01

    Crop rotation has been practiced for centuries in an effort to improve agricultural yield. However, the directions, magnitudes, and mechanisms of the yield effects of various crop rotations remain poorly understood in many systems. In order to better understand how crop rotation influences cotton yield, we used hierarchical Bayesian models to analyze a large ecoinformatics database consisting of records of commercial cotton crops grown in California's San Joaquin Valley. We identified several crops that, when grown in a field the year before a cotton crop, were associated with increased or decreased cotton yield. Furthermore, there was a negative association between the effect of the prior year's crop on June densities of the pest Lygus hesperus and the effect of the prior year's crop on cotton yield. This suggested that some crops may enhance L. hesperus densities in the surrounding agricultural landscape, because residual L. hesperus populations from the previous year cannot continuously inhabit a focal field and attack a subsequent cotton crop. In addition, we found that cotton yield declined approximately 2.4% for each additional year in which cotton was grown consecutively in a field prior to the focal cotton crop. Because L. hesperus is quite mobile, the effects of crop rotation on L. hesperus would likely not be revealed by small plot experimentation. These results provide an example of how ecoinformatics datasets, which capture the true spatial scale of commercial agriculture, can be used to enhance agricultural productivity.

  18. Ecoinformatics reveals effects of crop rotational histories on cotton yield.

    Directory of Open Access Journals (Sweden)

    Matthew H Meisner

    Full Text Available Crop rotation has been practiced for centuries in an effort to improve agricultural yield. However, the directions, magnitudes, and mechanisms of the yield effects of various crop rotations remain poorly understood in many systems. In order to better understand how crop rotation influences cotton yield, we used hierarchical Bayesian models to analyze a large ecoinformatics database consisting of records of commercial cotton crops grown in California's San Joaquin Valley. We identified several crops that, when grown in a field the year before a cotton crop, were associated with increased or decreased cotton yield. Furthermore, there was a negative association between the effect of the prior year's crop on June densities of the pest Lygus hesperus and the effect of the prior year's crop on cotton yield. This suggested that some crops may enhance L. hesperus densities in the surrounding agricultural landscape, because residual L. hesperus populations from the previous year cannot continuously inhabit a focal field and attack a subsequent cotton crop. In addition, we found that cotton yield declined approximately 2.4% for each additional year in which cotton was grown consecutively in a field prior to the focal cotton crop. Because L. hesperus is quite mobile, the effects of crop rotation on L. hesperus would likely not be revealed by small plot experimentation. These results provide an example of how ecoinformatics datasets, which capture the true spatial scale of commercial agriculture, can be used to enhance agricultural productivity.

  19. Ergonomic Evaluation of Battery Powered Portable Cotton Picker

    Science.gov (United States)

    Dixit, A.; Manes, G. S.; Singh, A.; Prakash, A.; Mahal, J. S.

    2012-09-01

    Ergonomic evaluation of battery powered portable manual cotton picker was carried out on two subjects for three cotton varieties and was compared against manual method of picking. It is a hand operated machine and has a pair of chain with small sharp edged teeth and sprockets and is operated by a light weight 12 V battery. Cotton gets entangled with the chain and is collected and guided into the collection bag. Average heart rate, oxygen consumption, workload, energy expenditure was more in case of cotton picking by manual cotton picker as compared to manual picking for both the subjects for all three cotton variety types. Oxygen consumption varied from 0.81 to 0.97 l/min, workload varied from 36.32 to 46.16 W and energy expenditure varied from 16.83 to 20.33 kJ/min for both the subject in case of machine picking for all three cotton varieties. The maximum discomfort experienced by the subjects during picking cotton by manual cotton picker was in right wrist palm, right forearm, upper and lower back, left shoulder and in lower legs and both feet.

  20. Problems and achievements of cotton (Gossypium Hirsutum L. weeds control

    Directory of Open Access Journals (Sweden)

    T. Barakova

    2017-09-01

    Full Text Available Abstract. Weed control in the cultivation of cotton is critical to the yield and quality of production. The influence of economically important weeds was studied. Chemical control is the most effective method of weed control in cotton but much of the information on it relates to primary weed infestation. Problems with primary weed infestation in cotton have been solved to a significant extent. The question of secondary weed infestation with annual and perennial graminaceous weeds during the period of cotton vegetation is also determined largely by the use of antigraminaceous herbicides. The data related to herbicides to effectively control secondary germinated broadleaf weeds in conventional technology for cotton growing are quite scarce, even globally. We are still seeking effective herbicides for control of these weeds in cotton crops. Studies on their influence on the sowing characteristics of cotton seed and the quality of cotton fiber are still insufficient. In the scientific literature there is not enough information on these questions. The combinations of herbicides, as well as their tank mixtures with fertilizers or plant growth regulators are more efficient than autonomous application. Often during their combined application higher synergistic effect on yield is produced. There is information about cotton cultivars resistant to glyphosate. These cultivars are GMO and they are banned within the European Union, including Bulgaria.

  1. Radiation synthesis of silver nanostructures in cotton matrix

    International Nuclear Information System (INIS)

    Chmielewska, Dagmara; Sartowska, Bożena

    2012-01-01

    Cotton is one of the most popular natural fibres, composed mainly of cellulose, which finds a wide range of applications in paper, textile and health care products industry. Researchers have focused their interest on the synthesis of cotton nanocomposites, which enhances its mechanical, thermal and antimicrobial properties by the incorporation of various nanoparticles into the cotton matrix. Silver is one of the most popular antimicrobial agents with a wide spectrum of antibacterial and antifungal activity that results from a complex mechanism of its interactions with the cells of harmful microorganism. In this work, electron beam radiation was applied to synthesise silver nanostructures in cotton fibres. Investigations of the influence of the initial silver salt concentration on the size and distribution of the obtained silver nanostructures were carried out. A detailed characterisation of these nanocomposites with SEM-BSE and EDS methods was performed. TGA and DSC analyses were performed to assess the influence of different size silver nanoparticles and the effect of electron beam irradiation on the thermal properties of cotton fibres. A microbiological investigation to determine the antibacterial activity of Ag-cotton nanocomposites was carried out. - Highlights: ► Ag NPs embedded in cotton matrix were synthesised by electron beam irradiation. ► Concentration of silver salt solution influences on size of silver nanoparticles. ► Silver content as well as irradiation affect thermal properties of cotton fabrics. ► Ag-cotton nanocomposites exhibit antibacterial activity against bacteria and fungi.

  2. Weed hosts of cotton mealybug, Phenacoccus solenopsis Tinsley (Hemiptera: Pseudococcidae).

    Science.gov (United States)

    Vennila, S; Prasad, Y G; Prabhakar, M; Agarwal, Meenu; Sreedevi, G; Bambawale, O M

    2013-03-01

    The exotic cotton mealybug, Phenacoccus solenopsis Tinsley (Hemiptera: Pseudococcidae) invaded India during 2006, and caused widespread infestation across all nine cotton growing states. P. solenopsis also infested weeds that aided its faster spread and increased severity across cotton fields. Two year survey carried out to document host plants of P. solenopsis between 2008 and 2010 revealed 27, 83, 59 and 108 weeds belonging to 8, 18, 10 and 32 families serving as alternate hosts at North, Central, South and All India cotton growing zones, respectively. Plant species of four families viz., Asteraceae, Amaranthaceae, Malvaceae and Lamiaceae constituted almost 50% of the weed hosts. While 39 weed species supported P. solenopsis multiplication during the cotton season, 37 were hosts during off season. Higher number of weeds as off season hosts (17) outnumbering cotton season (13) at Central over other zones indicated the strong carryover of the pest aided by weeds between two cotton seasons. Six, two and seven weed hosts had the extreme severity of Grade 4 during cotton, off and cotton + off seasons, respectively. Higher number of weed hosts of P. solenopsis were located at roadside: South (12) > Central (8) > North (3) zones. Commonality of weed hosts was higher between C+S zones, while no weed host was common between N+S zones. Paper furnishes the wide range of weed hosts of P. solenopsis, discusses their significance, and formulated general and specific cultural management strategies for nationwide implementation to prevent its outbreaks.

  3. Study of mungbean intercropping in cotton planted with different techniques

    International Nuclear Information System (INIS)

    Khan, M.B.; Khaliq, A.

    2004-01-01

    Bio-economic efficiency of different cotton-based intercropping systems was determined at the Agronomic Research Area, University of Agriculture, Faisalabad, (Pakistan) during 1996-1997 and 1997-98. Cotton cultivar NIAB-78 was planted in 80-cm apart single rows and 120-cm spaced double row strips with the help of a single row hand drill. Intercropping systems were cotton alone and cotton + mungbean. Experiment was laid out in a RCBD with split arrangements in four replications. Planting patterns were kept in main plots and intercropping systems in sub-plots. Inter crop was sown in the space between 80-cm apart single rows as well as 120-cm spaced double row strips. Competition functions like relative crowding coefficient, competitive ratio, aggressivity, land equivalent ratio and area time equivalent ratio were calculated for the assessment of the benefits of the intercropping. Partial budget was prepared for determining net field benefits of the systems under study. Growing of cotton in 120-cm spaced double row strips proved superior to 80-cm spaced single rows. Intercropping decreased the seed cotton production significantly in both years, however, inter crop not only covered this loss but also increased overall productivity. Higher net field benefit (NFB) was obtained from cotton + mungbean than sole cropping of cotton. Farmers with small land holdings, seriously constrained by low crop income can adopt the practice of intercropping of mungbean in cotton. (author)

  4. Chemical analysis of plasma-assisted antimicrobial treatment on cotton

    International Nuclear Information System (INIS)

    Kan, C W; Lam, Y L; Yuen, C W M; Luximon, A; Lau, K W; Chen, K S

    2013-01-01

    This paper explores the use of plasma treatment as a pretreatment process to assist the application of antimicrobial process on cotton fabric with good functional effect. In this paper, antimicrobial finishing agent, Microfresh Liquid Formulation 9200-200 (MF), and a binder (polyurethane dispersion, Microban Liquid Formulation R10800-0, MB) will be used for treating the cotton fabric for improving the antimicrobial property and pre-treatment of cotton fabric by plasma under atmospheric pressure will be employed to improve loading of chemical agents. The chemical analysis of the treated cotton fabric will be conducted by Fourier transform Infrared Spectroscopy.

  5. BENDING BEHAVIOUR OF MAGNETIC COTTON YARNS

    Directory of Open Access Journals (Sweden)

    LUPU Iuliana G.

    2017-05-01

    Full Text Available Magnetic yarns are composite yarns, i.e. they combine elements of various natures and properties, with proven potential for electromagnetic interference (EMI shielding. In this paper, different mixtures of hard and soft magnetic powder were chosen to cover materials made of cotton yarn. The physical properties and bending behavior of the produced composite yarns were investigated in order to evaluate the yarns for further textile processing.The cotton yarn used as base material was covered with hard (barium hexaferrite BaFe12O19 and soft (Black Toner magnetic particles. An in-house developed laboratory equipment has been used to cover the twist cotton yarns with seven mixtures having different amounts of magnetic powder (30% – 50%. The bending behavior of the coated yarns was evaluated based on the average width of cracks which appeared on the yarn surface after repeated flexural tests. The obtained results revealed that usage of a polyurethane adhesive in the coating solution prevents crack formation on the surface of hard magnetic yarns after flexural tests. At the same time, the higher the mass percentage of hard magnetic powder in the mixture, the higher was the cracks’ width. The soft magnetic yarns are more flexible and a smaller crack width is observed on their surface. Both the coating solution composition and the powder diameter are expected to influence the bending behavior of coated yarns.

  6. Cotton dust exposure and self-reported respiratory symptoms among textile factory workers in Northwest Ethiopia: a comparative cross-sectional study.

    Science.gov (United States)

    Daba Wami, Sintayehu; Chercos, Daniel Haile; Dessie, Awrajaw; Gizaw, Zemichael; Getachew, Atalay; Hambisa, Tesfaye; Guadu, Tadese; Getachew, Dawit; Destaw, Bikes

    2018-01-01

    Cotton dust induced respiratory disorders are dramatically increased over the globe, especially the problem is serious in developing countries. Respiratory symptoms, such as cough, phlegm, wheezing, shortness of breath, chest tightness, chronic bronchitis, and byssinosis are common among workers exposed to cotton dust. However, in Ethiopia, the magnitude of the problem is not well known and information is limited about the risk factors. Therefore, this study was aimed to assess the prevalence of respiratory symptoms and associated factors. A Comparative cross-sectional study design was employed. A total of 413 (276 exposed and 137 unexposed) participants were included in the study. Stratified and simple random sampling techniques were used to select exposed and unexposed groups to cotton dust respectively. Multivariable binary logistic regression analyses was performed to identify variables associated with respiratory symptoms and adjusted odds ratio (AOR) was used to determine the strength of associations. Significance level was obtained at 95% confidence interval (CI) and p -value ≤0.05. The prevalence of self-reported respiratory symptoms was 47.8% (95% CI: 41.3, 53.7%) and 15.3% (95% CI: 9.6, 22.3%) among exposed and control groups respectively. Sex (AOR = 2.1, 95% CI: 1.29, 3.45), service year (AOR = 2.38, 95% CI: 1.19, 4.71) and ventilation (AOR = 2.4, 95% CI: 1.17, 4.91) were factors significantly associated with respiratory symptoms. Furthermore, working department such as; ginning (AOR = 5.1, 95% CI: 2.13, 12.16), spinning (AOR = 4.96, 95% CI: 2.18, 11.29), weaving (AOR = 5.9, 95% CI: 2.46, 14.27) and blowing working departments (AOR = 5.14, 95% CI: 1.4, 18.94) were significantly associated with respiratory disorders. The prevalence of self-reported respiratory symptoms was higher among workers exposed to cotton dust than unexposed workers. Sex, service year, working department and work unit ventilation were predictor

  7. Profile of small interfering RNAs from cotton plants infected with the polerovirus Cotton leafroll dwarf virus

    Directory of Open Access Journals (Sweden)

    Schrago Carlos EG

    2011-08-01

    Full Text Available Abstract Background In response to infection, viral genomes are processed by Dicer-like (DCL ribonuclease proteins into viral small RNAs (vsRNAs of discrete sizes. vsRNAs are then used as guides for silencing the viral genome. The profile of vsRNAs produced during the infection process has been extensively studied for some groups of viruses. However, nothing is known about the vsRNAs produced during infections of members of the economically important family Luteoviridae, a group of phloem-restricted viruses. Here, we report the characterization of a population of vsRNAs from cotton plants infected with Cotton leafroll dwarf virus (CLRDV, a member of the genus Polerovirus, family Luteoviridae. Results Deep sequencing of small RNAs (sRNAs from leaves of CLRDV-infected cotton plants revealed that the vsRNAs were 21- to 24-nucleotides (nt long and that their sequences matched the viral genome, with higher frequencies of matches in the 3- region. There were equivalent amounts of sense and antisense vsRNAs, and the 22-nt class of small RNAs was predominant. During infection, cotton Dcl transcripts appeared to be up-regulated, while Dcl2 appeared to be down-regulated. Conclusions This is the first report on the profile of sRNAs in a plant infected with a virus from the family Luteoviridae. Our sequence data strongly suggest that virus-derived double-stranded RNA functions as one of the main precursors of vsRNAs. Judging by the profiled size classes, all cotton DCLs might be working to silence the virus. The possible causes for the unexpectedly high accumulation of 22-nt vsRNAs are discussed. CLRDV is the causal agent of Cotton blue disease, which occurs worldwide. Our results are an important contribution for understanding the molecular mechanisms involved in this and related diseases.

  8. Profile of small interfering RNAs from cotton plants infected with the polerovirus Cotton leafroll dwarf virus.

    Science.gov (United States)

    Silva, Tatiane F; Romanel, Elisson A C; Andrade, Roberto R S; Farinelli, Laurent; Østerås, Magne; Deluen, Cécile; Corrêa, Régis L; Schrago, Carlos E G; Vaslin, Maite F S

    2011-08-24

    In response to infection, viral genomes are processed by Dicer-like (DCL) ribonuclease proteins into viral small RNAs (vsRNAs) of discrete sizes. vsRNAs are then used as guides for silencing the viral genome. The profile of vsRNAs produced during the infection process has been extensively studied for some groups of viruses. However, nothing is known about the vsRNAs produced during infections of members of the economically important family Luteoviridae, a group of phloem-restricted viruses. Here, we report the characterization of a population of vsRNAs from cotton plants infected with Cotton leafroll dwarf virus (CLRDV), a member of the genus Polerovirus, family Luteoviridae. Deep sequencing of small RNAs (sRNAs) from leaves of CLRDV-infected cotton plants revealed that the vsRNAs were 21- to 24-nucleotides (nt) long and that their sequences matched the viral genome, with higher frequencies of matches in the 3- region. There were equivalent amounts of sense and antisense vsRNAs, and the 22-nt class of small RNAs was predominant. During infection, cotton Dcl transcripts appeared to be up-regulated, while Dcl2 appeared to be down-regulated. This is the first report on the profile of sRNAs in a plant infected with a virus from the family Luteoviridae. Our sequence data strongly suggest that virus-derived double-stranded RNA functions as one of the main precursors of vsRNAs. Judging by the profiled size classes, all cotton DCLs might be working to silence the virus. The possible causes for the unexpectedly high accumulation of 22-nt vsRNAs are discussed. CLRDV is the causal agent of Cotton blue disease, which occurs worldwide. Our results are an important contribution for understanding the molecular mechanisms involved in this and related diseases.

  9. Ginástica Laboral: efeitos de um programa de ginástica laboral sobre a flexibilidade em trabalhadores de diversos setores de um hospital de ensino da região do Vale do Rio Pardo/RS

    Directory of Open Access Journals (Sweden)

    Andréa Mattos de Andrade

    2015-12-01

    Full Text Available A Ginástica Laboral (GL é uma atividade física realizada durante a jornada de trabalho, com exercício de compensação aos movimentos repetitivos, à ausência de movimentos, ou a posturas desconfortáveis assumidas durante o período de trabalho. Objetivo: verificar possíveis efeitos de um programa de GL sobre a flexibilidade em trabalhadores de diversos setores de um hospital de ensino da região do Vale do Rio Pardo/RS. Método: estudo semi-experimental realizado em diversos setores de um hospital, de março de 2014 a maio 2015, em que foram avaliados 42 indivíduos, do sexo feminino, com idade entre 22 e 58 anos, que participavam do programa de GL. Para a coleta de dados, foi aplicado o teste sentar e alcançar (sit and reach e o teste do manguito rotador (ombro direito e esquerdo em três momentos: 1 (antes da intervenção com GL; 2 (logo após o término da intervenção e 3 (quatro meses, após a intervenção. Resultados: a flexibilidade diferiu na comparação entre os momentos 1 e 2 e entre os momentos 1 e 3, em todos os testes aplicados, demonstrando que o programa de GL melhorou os níveis de flexibilidade dos trabalhadores. Não foi observada diferença significativa entre os momentos 2 e 3. Considerações finais: o programa de GL melhorou os níveis de flexibilidade dos trabalhadores, mantendo esses níveis semelhantes seis meses após o término da intervenção.

  10. Fate of selected microorganisms when introduced as cross-contamination inocula into simulated food trash compartment waste

    Science.gov (United States)

    Strayer, Richard; Hummerick, Mary; Richards, Jeffrey; Birmele, Michele; Roberts, Michael

    AdHocReviewCycleID-309796538 NewReviewCycle EmailSubjectPlease review this (?today?) AuthorEm Richard F. (KSC)[DYNAMAC CORP] ReviewingToolsShownOnceurn:schemas-microsoft-com:office:smart One goal of Exploration Life Support solid waste processing is to stabilize wastes for storage, mitigate crew risks, and enable resource recovery. Food and crew fecal wastes contain easily biodegraded organic components that support microbial growth. Our objective is to determine a baseline for the fate of selected microbes in wastes prior to processing treatments. Challenge microbes, including human-associated pathogens, were added to unsterilized, simulated food trash solid waste containing a mixed microbial community. The fate of the microbial community and challenge microbes was determined over a 6 week time course of waste storage. Challenge microbes were selected from a list of microorganisms common to residual food or fecal wastes and included: Escherichia coli, Salmonella enterica serovar typhimurium, Staphylococcus aureus, Pseudomonas aeruginosa, Aspergillus niger (a common mold), and Bacillus pumilus SAFR-032, a spore-forming bacterium previously isolated from spacecraft assembly facilities selected for its resistance to heat, uv, and desiccation. The trash model simulant contained 80% food trash (food waste and containers) and 20% hygiene wipes. Cultures of challenge microbes were grown overnight on Nutrient Agar (Difco), harvested, re-suspended in physiological saline, and diluted to achieve the desired optical density for inoculation. The six organisms were pooled and inoculated into the simulated food wastes and packaging before manual mixing. Inoculated simulated waste was stored in custom FlexfoilTM gas sampling bags (SKC, Inc.) which were then connected to a gas analysis system designed to supply fresh air to each bag to maintain O2 above 1%. Bag headspace was monitored for CO2 (PP Systems) and O2 (Maxtec). Total microbes were quantified by microscopic direct

  11. Field Comparison of Fertigation Vs. Surface Irrigation of Cotton Crop

    International Nuclear Information System (INIS)

    Janat, M.

    2004-01-01

    Based on previous results of the same nature, one nitrogen rate 180 kg N ha -1 was tested under two-irrigation methods, surface irrigation and drip fertigation of cotton (Cultivar Rakka-5) for two consecutive seasons 2000 and 2001. The study aimed to answer various questions regarding the applicability of drip fertigation at farm level and the effect of its employment on yield and growth parameters, compared to surface irrigation. Nitrogen fertilizer was either injected in eight equally split applications for the drip fertigated cotton or divided in four unequally split applications as recommend by Ministry of Agriculture (20% before planting, 40% at thinning, 20% after 60 days from planting and 20% after 75 days after planting). 15 N labeled urea was used to evaluate nitrogen fertilizer efficiency. The experimental design was randomized block design with seven replicates. Results showed that drip fertigation led to water saving exceeding 50% in some cases. Field germination percentage was highly increased under drip- fertigated cotton relative to surface-irrigated cotton. Dry matter and seed cotton yield of surface-irrigated cotton was slightly higher than that of drip-fertigated cotton in the first growing season. The reason for that was due to the hot spill that occurred in the region, which exposed the cotton crop to water stress and consequently pushed the cotton into early flowering. Lint properties were not affected by the introduction of drip-fertigation. Actually some properties were improved relative to the standard properties identified by the cotton Bureau.Nitrogen uptake was slightly increased under drip fertigation whereas nitrogen use efficiencies were not constant along the growing seasons. The reason for that could be lateral leaching and root proliferation into the labeled and unlabeled subplots. Field water use efficiency was highly increased for both growing seasons under drip fertigation practice. The rate of field water use efficiencies

  12. Fluvial Export Variability Of Limiting Nutrient Fluxes To The Indian Ocean From Kelani, Kalu and Gin Rivers Of Sri Lanka

    Science.gov (United States)

    Ranasinghage, P. N.; Silva, A. N.; Vlahos, P.

    2016-12-01

    Inorganic `reactive' nutrients hold the highest importance in understanding the role of limiting nutrients in the ocean since they facilitate marine biological productivity and carbon sequestration that would eventually pave the way to regulate the biogeochemical climate feedbacks. Significant inorganic fractions are expected to be exported episodically to the ocean from fluvial fluxes though this is poorly understood. Thus, no considerable amounts of published work regarding the fluxes from Sri Lankan freshwater streams have ever been recorded. A study was carried out to quantify the contribution of Kelani, Kalu and Gin Rivers, three major rivers in the wet zone of Sri Lanka, in exporting major limiting nutrient fluxes to the Indian Ocean; to understand the significance of their variability patterns with rainfall and understand differences in their inputs. The study was conducted during the summer monsoonal period from late August to early November at two-three week intervals where water samples were collected for ammonia, nitrite, nitrate, orthophosphate, silica, sulfate and iron analysis by Colorimetric Spectroscopy. Discharge and rainfall data were retrieved from the Department of Irrigation and Department of Meteorology, Sri Lanka respectively. According to Two Way ANOVA, none of the individual fluxes showed significant differences (p>0.1) both in their temporal and spatial variability suggesting that studied rivers respond similarly in fluvial transportation owing to the similar rainfall intensities observed during the study period in the wet zone. Linear Regression Analysis indicates that only PO43- (p<0.01), SO42- (p<0.01) and NO2-(p<0.01 for Kelani and Kalu; 0.0.1Key words; nutrients, fluvial, fluxes, Redfield ratios

  13. Carbon contributions from roots in cotton based rotations

    Science.gov (United States)

    Tan, D. K. Y.; Hulugalle, N. R.

    2012-04-01

    Most research on the decline in soil organic carbon (SOC) stocks in Australian cotton farming systems has focussed on the inputs from above-ground crop residues, with contribution from roots being less studied. This paper aims to outline the contribution of cotton roots and roots of other crops to soil carbon stocks in furrow-irrigated Vertisols in several cotton (Gossypium hirsutum L.)-based rotations. Data was collected from cotton-based rotation systems: cotton monoculture, cotton-vetch (Vicia benghalensis) Roth.), cotton-wheat (Triticum aestivum L.), cotton-wheat-vetch, cotton-corn, corn-corn, cotton-sorghum (Sorghum bicolor L.) and from BollgardTM II (Bt) and non-Bt cotton. Land management systems were permanent beds, with or without standing stubble, and conventional tillage. Root growth in the surface 0.10 m was measured with the core-break method, and that in the 0.10 to 1.0 m depth with a minirhizotron and I-CAP image capture system. These measurements were used to derive root C added to soil through intra-seasonal root death (Clost), C in roots remaining at the end of season (Croot), and total root C added to soil (Ctotal = Croot + Clost). Ctotal in non-Bt cotton (Sicot 80RRF, 0.9 t C/ha/year) was higher than in Bt cotton (Sicot 80RRF, 0.6 t C/ha/year). Overall, Ctotal from cotton roots ranges between 0.5 to 5 t C/ha/year, with Clost contributing 25-70%. Ctotal was greater with vetch than with wheat and was in the order of vetch in cotton-wheat-vetch (5.1 t C/ha/year) > vetch in cotton-vetch (1.9 t C/ha/year) > wheat in cotton-wheat (1.6 t C/ha/year) = wheat in cotton-wheat-vetch (1.7 t C/ha/year). Intra-seasonal root mortality accounted for 12% of total root carbon in vetch and 36% in wheat. Average corn Ctotal with monoculture was 9.3 t/ha and with cotton-corn 5.0 t/ha. Ctotal averaged between both treatments was, thus, of the order of 7.7 t C/ha/year and average Clost 0.04 t/ha/yr. Sorghum roots contributed less carbon with conventional tillage (8.2 t

  14. [Effects of cotton stalk biochar on microbial community structure and function of continuous cropping cotton rhizosphere soil in Xinjiang, China].

    Science.gov (United States)

    Gu, Mei-ying; Tang, Guang-mu; Liu, Hong-liang; Li, Zhi-qiang; Liu, Xiao-wei; Xu, Wan-li

    2016-01-01

    In this study, field trials were conducted to examine the effects of cotton stalk biochar on microbial population, function and structural diversity of microorganisms in rhizosphere soil of continuous cotton cropping field in Xinjiang by plate count, Biolog and DGGE methods. The experiment was a factorial design with four treatments: 1) normal fertilization with cotton stalk removed (NPK); 2) normal fertilization with cotton stalk powdered and returned to field (NPKS); 3) normal fertilization plus cotton stalk biochar at 22.50 t · hm⁻² (NPKB₁); and 4) normal fertilization plus cotton stalk biochar at 45.00 t · hm⁻² (NPKB₂). The results showed that cotton stalk biochar application obviously increased the numbers of bacteria and actinomycetes in the rhizospheric soil. Compared with NPK treatment, the number of fungi was significantly increased in the NPKB₁treatment, but not in the NPKB₂ treatment. However, the number of fungi was generally lower in the biochar amended (NPKB₁, NPKB₂) than in the cotton stalk applied plots (NPKS). Application of cotton stalk biochar increased values of AWCD, and significantly improved microbial richness index, suggesting that the microbial ability of utilizing carbohydrates, amino acids and carboxylic acids, especially phenolic acids was enhanced. The number of DGGE bands of NPKB₂ treatment was the greatest, with some species of Gemmatimonadetes, Acidobacteria, Proteobacteria and Actinobacteria being enriched. UPGMC Cluster analysis pointed out that bacterial communities in the rhizospheric soil of NPKB₂ treatment were different from those in the NPK, NPKS and NPKB₁treatments, which belonged to the same cluster. These results indicated that application of cotton stalk biochar could significantly increase microbial diversity and change soil bacterial community structure in the cotton rhizosphere soil, thus improving the health of soil ecosystem.

  15. Preliminary assessments of portable color spectrophotometer measurements of cotton color

    Science.gov (United States)

    Cotton in the U.S. is classified for color with the Uster® High Volume Instrument (HVI), using the parameters Rd (diffuse reflectance) and +b (yellowness). It has been reported that some cotton bales, especially those transported overseas, appear to have changed significantly in color from their in...

  16. 78 FR 54970 - Cotton Futures Classification: Optional Classification Procedure

    Science.gov (United States)

    2013-09-09

    ... Service 7 CFR Part 27 [AMS-CN-13-0043] RIN 0581-AD33 Cotton Futures Classification: Optional Classification Procedure AGENCY: Agricultural Marketing Service, USDA. ACTION: Proposed rule. SUMMARY: The... optional cotton futures classification procedure--identified and known as ``registration'' by the U.S...

  17. Effect of nitrates on embryo induction efficiency in cotton (Gossypium ...

    African Journals Online (AJOL)

    Fred

    cotton species (Zhang, 1994b). Somatic embryogenesis and plant regeneration systems have been established from cotton tissue, protoplasts and ovules (Zhang and Li,. 1992; Feng and Zhang, 1994; Zhang, 1995). Regeneration procedures have been used to obtain genetically modified plants after Agrobacterium- ...

  18. Efficacy of some synthetic insecticides for control of cotton bollworms ...

    African Journals Online (AJOL)

    ... and Betsulfan at 3.2 l ha-1 recorded the highest and lowest yields, respectively. For effective control of cotton bollworms for maximum yield in the ecology, Thionex applied at 2.8 l ha-1 is recommended. Keywords: Control, cotton bollworms, efficacy, Ghana, synthetic insecticides. African Crop Science Journal, Vol. 20, No.

  19. Quantification and characterization of cotton crop biomass residue

    Science.gov (United States)

    Cotton crop residual biomass remaining in the field after mechanical seed cotton harvest is not typically harvested and utilized off-site thereby generating additional revenue for producers. Recently, interest has increased in utilizing biomass materials as feedstock for the production of fuel and ...

  20. Crop residue inventory estimates for Texas High Plains cotton

    Science.gov (United States)

    Interest in the use of cotton crop by-products for the production of bio-fuels and value-added products is increasing. Research documenting the availability of cotton crop by-products after machine harvest is needed. The objectives of this work were to document the total biomass production for moder...

  1. Productivity and resource use in cotton and wheat relay intercropping

    NARCIS (Netherlands)

    Zhang, L.

    2007-01-01

    Keywords: Grain yield; lint yield; phenological delay; light use; nitrogen use; resource use efficiency; modelling; profitability; water productivity. From the early 1980s onwards, farmers in the Yellow River cotton producing region intercropped cotton and winter wheat; currently on more than 60% of

  2. Leaf tissue assay for lepidopteran pests of Bt cotton

    Science.gov (United States)

    Laboratory measurements of susceptibility to Bt toxins can be a poor indicator of the ability of an insect to survive on transgenic crops. We investigated the potential of using cotton leaf tissue for evaluating heliothine susceptibilities to two dual-gene Bt cottons. A preliminary study was conduct...

  3. Sequencing of a Cultivated Diploid Cotton Genome-Gossypium arboreum

    Institute of Scientific and Technical Information of China (English)

    WILKINS; Thea; A

    2008-01-01

    Sequencing the genomes of crop species and model systems contributes significantly to our understanding of the organization,structure and function of plant genomes.In a `white paper' published in 2007,the cotton community set forth a strategic plan for sequencing the AD genome of cultivated upland cotton that initially targets less complex diploid genomes.This strategy banks on the high degree

  4. Polyploidization altered gene functions in cotton (Gossypium spp.)

    Science.gov (United States)

    Cotton fibers are seed trichomes derived from individual cells of the epidermal layer of the seed coat. It has been known for a long time that a large set of genes determine the development of cotton fiber, and more recently it has been determined that these genes are distributed across the At and ...

  5. Current university and USDA lab cotton contamination research

    Science.gov (United States)

    U.S. cotton is considered to have some of the lowest levels of contamination in the world. However, that reputation is in jeopardy as complaints of contamination from domestic and foreign mills are on the rise. Cotton contamination can be classified under four major categorizes: fabrics and strings ...

  6. Nitrogen economy in relay intercropping systems of wheat and cotton

    NARCIS (Netherlands)

    Zhang, L.Z.; Spiertz, J.H.J.; Zhang, S.; Li, B.; Werf, van der W.

    2008-01-01

    Relay intercropping of wheat and cotton is practiced on a large scale in China. Winter wheat is thereby grown as a food crop from November to June and cotton as a cash crop from April to October. The crops overlap in time, growing as an intercrop, from April till June. High levels of nitrogen are

  7. Molecular systematics of the cotton root rot pathogen, Phymatotrichopsis omnivora

    NARCIS (Netherlands)

    Marek, S.M.; Hansen, K.; Romanish, M.; Thorn, R.G.

    2009-01-01

    Cotton root rot is an important soilborne disease of cotton and numerous dicot plants in the south-western United States and Mexico. The causal organism, Phymatotrichopsis omnivora (= Phymatotrichum omnivorum), is known only as an asexual, holoanamorphic (mitosporic) fungus, and produces conidia

  8. Governing the transnational organic cotton network from Benin

    NARCIS (Netherlands)

    Glin, L.C.; Mol, A.P.J.; Oosterveer, P.J.M.; Vodouhè, S.

    2012-01-01

    In this article, we attempt to conceptualize the historical development and the governance structure of the transnational organic cotton network from Benin. We aim to discover how the organic cotton production-consumption network is governed locally and internationally. Existing bodies of literature

  9. Role of secondary metabolites biosynthesis in resistance to cotton ...

    African Journals Online (AJOL)

    use

    2011-12-12

    Dec 12, 2011 ... Disease percentage on six cotton varieties with respect to time for cotton leaf curl virus (CLCuV) was evaluated. In August 2007, the maximum disease was observed in CIM-506, CYTO-89 and BH-118. (susceptible), whereas CIM-443 was resistant with lower disease percentage. It was found that the leaf.

  10. 7 CFR 28.8 - Classification of cotton; determination.

    Science.gov (United States)

    2010-01-01

    ... Standards Act Administrative and General § 28.8 Classification of cotton; determination. For the purposes of the Act, the classification of any cotton shall be determined by the quality of a sample in accordance... employees will determine all fiber property measurements using High Volume Instruments. The classification...

  11. Statistical behavior of the tensile property of heated cotton fiber

    Science.gov (United States)

    The temperature dependence of the tensile property of single cotton fiber was studied in the range of 160-300°C using Favimat test, and its statistical behavior was interpreted in terms of structural changes. The tenacity of control cotton fiber was well described by the single Weibull distribution,...

  12. 7 CFR 27.73 - Supervision of transfers of cotton.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Supervision of transfers of cotton. 27.73 Section 27.73 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER REGULATIONS COTTON CLASSIFICATION UNDER...

  13. 76 FR 80278 - Revision of Cotton Classification Procedures for Determining Cotton Leaf Grade

    Science.gov (United States)

    2011-12-23

    ... challenge to the provisions of this rule. Regulatory Flexibility Act Pursuant to requirements set forth in... currently part of the official USDA cotton classification. Accurate assignment of leaf grade is of economic... cost factor associated with its removal. Furthermore, since small leaf particles cannot always be...

  14. 77 FR 20503 - Revision of Cotton Classification Procedures for Determining Cotton Leaf Grade

    Science.gov (United States)

    2012-04-05

    ... measurements for other quality factors are performed by precise HVI measurements, manual determinations for.... Accurate assignment of leaf grade is of economic importance to all participants along the cotton supply... significant economic impact on a substantial number of small entities. Fees paid by users of the service are...

  15. Ammonium carboxylate production from sugarcane trash using long-term air-lime pretreatment followed by mixed-culture fermentation.

    Science.gov (United States)

    Nachiappan, Balasubramaniyan; Fu, Zhihong; Holtzapple, Mark T

    2011-03-01

    Sugarcane trash (ST) was converted to ammonium carboxylates using a novel bioprocessing strategy known as long-term air-lime pretreatment/mixed-culture fermentation. At mild conditions (50°C, 5 weeks, 1-atm air, and excess lime loading of 0.4 g Ca(OH)(2)/(g dry biomass)), air-lime pretreatment of ST had moderate delignification (64.4%) with little loss in polysaccharides. Without employing detoxification, sterility, expensive nutrients, or costly enzymes, the feedstock (80% treated ST/20% chicken manure) was fermented to primarily ammonium acetate (>75%) and butyrate by a mixed culture of marine microorganisms at 55°C. In the best four-stage countercurrent fermentation, the product yield was 0.36 g total acids/(g VS fed) and the substrate conversion was 64%. Model predictions indicate both high acid concentrations (>47.5 g/L) and high substrate conversions (>70%) are possible at industrial scale. Copyright © 2010 Elsevier Ltd. All rights reserved.

  16. Cost avoidance techniques through the Fernald controlled area trash segregation program and the RIMIA solid waste reduction program

    International Nuclear Information System (INIS)

    Menche, C.E.

    1997-01-01

    The Fernald Environmental Management Project is a Department of Energy owned facility that produced high quality uranium metals for military defense. The Fernald mission has changed from one of production to remediation. Remediation is intended to clean up legacy (primary) waste from past practices. Little opportunity is available to reduce the amount of primary waste. However, there is an opportunity to reduce secondary waste generation, primarily through segregation. Two programs which accomplish this are the Controlled Area Trash Segregation Program and the RIMIA Solid Waste Reduction Program. With these two programs now in place at the FEMP, it has been estimated that a 60% reduction has been achieved in unnecessary clean waste being disposed as Low Level Waste at the Nevada Test Site. The cost savings associated with these programs (currently 79,000 cubic feet, $428,000) could easily run into the millions of dollars based on the upcoming restoration activities to be undertaken. The segregation of non-radiological waste in the radiologically Controlled Area not only establishes a firm commitment to send only low-level radioactive waste to the Nevada Test Site, but also results in substantial cost avoidance

  17. Transtorno alimentar e variáveis comportamentais relacionadas ao excercício físico em academia de ginástica

    OpenAIRE

    Weis, Andréia

    2013-01-01

    Resumo: O objetivo do estudo foi analisar variáveis comportamentais relacionadas ao exercício físico (compromisso ao exercício físico, modalidades praticadas, objetivos para prática e características de treinamento) em pessoas com transtorno alimentar frenquentadoras de uma academia de ginástica de Balneário Camboriú - SC. Participaram da pesquisa 239 indivíduos, sendo 139 mulheres (32,2, ±11,0 anos) e 100 homens (31,4, ±13,1 anos). Os sujeitos responderam o Teste de Atitudes Alimentares (EAT...

  18. Hipotensão pós-exercício em idosas hipertensas controladas, após uma aula de ginástica localizada

    OpenAIRE

    Silva, Natal da

    2012-01-01

    O presente estudo teve como objetivo avaliar a Hipotensão pós-exercício em idosas hipertensas com pressão arterial controlada por medicamentos anti-hipertensivos, em uma aula de ginástica localizada de intensidade moderada de acordo com a escala de Borg. Para tanto, a amostra foi composta por 13 idosas ativas do CCI (Centro de Convivência do Idoso) do Recanto das Emas/DF, as quais foram aplicadas um questionário contendo 10 questões, com o intuito de conhecer a vida pregressa do indivíduo em ...

  19. Gerenciamento de custos para tomada de decisão - estudo em academia de musculação e ginástica

    OpenAIRE

    Góes, Dhiandra Amabille Simões

    2014-01-01

    Artigo – Trabalho de Conclusão de Curso apresentado à Fundação Universidade Federal de Rondônia – UNIR – Câmpus Prof. Francisco Gonçalves Quiles como requisito parcial para a obtenção do grau em Bacharel em Ciências Contábeis. Orientadora Profa. Me. Liliane Maria Nery Andrade o presente artigo apresenta os resultados de uma pesquisa de campo, exploratória e aplicada realizada em uma academia de ginástica localizada no município de Cacoal - RO. O objetivo da pesquisa foi identificar a deman...

  20. A facile method to fabricate superhydrophobic cotton fabrics

    Science.gov (United States)

    Zhang, Ming; Wang, Shuliang; Wang, Chengyu; Li, Jian

    2012-11-01

    A facile and novel method for fabricating superhydrophobic cotton fabrics is described in the present work. The superhydrophobic surface has been prepared by utilizing cationic poly (dimethyldiallylammonium chloride) and silica particles together with subsequent modification of (heptadecafluoro-1,1,2,2-tetradecyl) trimethoxysilane. The size distribution of silica particles was measured by Particle Size Analyzer. The cotton textiles before and after treatment were characterized by using scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). The wetting behavior of cotton samples was investigated by water contact angle measurement. Moreover, the superhydrophobic durability of coated cotton textiles has been evaluated by exposure, immersion and washing tests. The results show that the treated cotton fabrics exhibited excellent chemical stability and outstanding non-wettability with the WCA of 155 ± 2°, which offers an opportunity to accelerate the large-scale production of superhydrophobic textiles materials for new industrial applications.

  1. 21 CFR 182.70 - Substances migrating from cotton and cotton fabrics used in dry food packaging.

    Science.gov (United States)

    2010-04-01

    ... used in dry food packaging. 182.70 Section 182.70 Food and Drugs FOOD AND DRUG ADMINISTRATION... used in dry food packaging. Substances migrating to food from cotton and cotton fabrics used in dry food packaging that are generally recognized as safe for their intended use, within the meaning of...

  2. Fabrication of recyclable superhydrophobic cotton fabrics

    Science.gov (United States)

    Han, Sang Wook; Park, Eun Ji; Jeong, Myung-Geun; Kim, Il Hee; Seo, Hyun Ook; Kim, Ju Hwan; Kim, Kwang-Dae; Kim, Young Dok

    2017-04-01

    Commercial cotton fabric was coated with SiO2 nanoparticles wrapped with a polydimethylsiloxane (PDMS) layer, and the resulting material surface showed a water contact angle greater than 160°. The superhydrophobic fabric showed resistance to water-soluble contaminants and maintained its original superhydrophobic properties with almost no alteration even after many times of absorption-washing cycles of oil. Moreover, superhydrophobic fabric can be used as a filter to separate oil from water. We demonstrated a simple method of fabrication of superhydrophobic fabric with potential interest for use in a variety of applications.

  3. Phosphorus response in two varieties of cotton

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Mahendra; Bhandari, D K; Kumar, Vinod [Haryana Agricultural Univ., Hissar (India)

    1974-09-01

    Phosphorus requirements of cotton varieties H-14 and J-34 were studied on seirozem soils of Hissar under greenhouse conditions. The dry matter yield of both the varieties increased significantly upto 120 kg/ha P after which dry matter yield decreased. Total P uptake also increased with the addition of P. The highest utilization of fertilizer P by H-14 and J-34 was observed at 240 kg and 120 kg/ha levels of applied P, respectively. H-14 utilized more native P than J-34 at all levels of P application.

  4. Marketing policies and economic interests in the cotton sector of Kenya

    NARCIS (Netherlands)

    Dijkstra, T.

    1990-01-01

    This report, which is based on field research carried out in 1988, examines the marketing arrangements for raw cotton, cotton lint and cotton seed in Kenya, as well as the relationships and conflicts between the actors involved. The report starts with the history of cotton production and marketing

  5. CCI and CI Join Hands:A Better Supply Chain with More Innovations on Cotton Fabrics

    Institute of Scientific and Technical Information of China (English)

    Tom; Xue

    2010-01-01

    Cotton Council International("CCI")and Cotton Incorporated("CI") joined forces again,from October 19-22,2010 at Intertextile Shanghai,to promote natural fiber-U.S.cotton.As global textile strategic partners,both organizations were bringing together alliances through the cotton

  6. 7 CFR 28.107 - Original cotton standards and reserve sets.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Original cotton standards and reserve sets. 28.107... Standards Act Practical Forms of Cotton Standards § 28.107 Original cotton standards and reserve sets. (a) The containers of the original Universal Standards and other official cotton standards of the United...

  7. Using Agricultural Residue Biochar to Improve Soil Quality of Desert Soils

    Directory of Open Access Journals (Sweden)

    Yunhe Zhang

    2016-03-01

    Full Text Available A laboratory study was conducted to test the effects of biochars made from different feedstocks on soil quality indicators of arid soils. Biochars were produced from four locally-available agricultural residues: pecan shells, pecan orchard prunings, cotton gin trash, and yard waste, using a lab-scale pyrolyzer operated at 450 °C under a nitrogen environment and slow pyrolysis conditions. Two local arid soils used for crop production, a sandy loam and a clay loam, were amended with these biochars at a rate of 45 Mg·ha−1 and incubated for three weeks in a growth chamber. The soils were analyzed for multiple soil quality indicators including soil organic matter content, pH, electrical conductivity (EC, and available nutrients. Results showed that amendment with cotton gin trash biochar has the greatest impact on both soils, significantly increasing SOM and plant nutrient (P, K, Ca, Mn contents, as well as increasing the electrical conductivity, which creates concerns about soil salinity. Other biochar treatments significantly elevated soil salinity in clay loam soil, except for pecan shell biochar amended soil, which was not statistically different in EC from the control treatment. Generally, the effects of the biochar amendments were minimal for many soil measurements and varied with soil texture. Effects of biochars on soil salinity and pH/nutrient availability will be important considerations for research on biochar application to arid soils.

  8. Engineering cotton (Gossypium hirsutum L.) for resistance to cotton leaf curl disease using viral truncated AC1 DNA sequences.

    Science.gov (United States)

    Hashmi, Jamil A; Zafar, Yusuf; Arshad, Muhammad; Mansoor, Shahid; Asad, Shaheen

    2011-04-01

    Several important biological processes are performed by distinct functional domains found on replication-associated protein (Rep) encoded by AC1 of geminiviruses. Two truncated forms of replicase (tAC1) gene, capable of expressing only the N-terminal 669 bp (5'AC1) and C-terminal 783 bp (3'AC1) nucleotides cloned under transcriptional control of the CaMV35S were introduced into cotton (Gossypium hirsutum L.) using LBA4404 strain of Agrobacterium tumefaciens to make use of an interference strategy for impairing cotton leaf curl virus (CLCuV) infection in transgenic cotton. Compared with nontransformed control, we observed that transgenic cotton plants overexpressing either N-terminal (5'AC1) or C-terminal (3'AC1) sequences confer resistance to CLCuV by inhibiting replication of viral genomic and β satellite DNA components. Molecular analysis by Northern blot hybridization revealed high transgene expression in early and late growth stages associated with inhibition of CLCuV replication. Of the eight T(1) transgenic lines tested, six had delayed and minor symptoms as compared to nontransformed control lines which developed disease symptoms after 2-3 weeks of whitefly-mediated viral delivery. Virus biological assay and growth of T(2) plants proved that transgenic cotton plants overexpressing 5'- and 3'AC1 displayed high resistance level up to 72, 81%, respectively, as compared to non-transformed control plants following inoculation with viruliferous whiteflies giving significantly high cotton seed yield. Progeny analysis of these plants by polymerase chain reaction (PCR), Southern blotting and virus biological assay showed stable transgene, integration, inheritance and cotton leaf curl disease (CLCuD) resistance in two of the eight transgenic lines having single or two transgene insertions. Transgenic cotton expressing partial AC1 gene of CLCuV can be used as virus resistance source in cotton breeding programs aiming to improve virus resistance in cotton crop.

  9. Identification of top-down forces regulating cotton aphid population growth in transgenic Bt cotton in central China.

    Directory of Open Access Journals (Sweden)

    Peng Han

    Full Text Available The cotton aphid Aphis gossypii Glover is the main aphid pest in cotton fields in the Yangtze River Valley Cotton-planting Zone (YRZ in central China. Various natural enemies may attack the cotton aphid in Bt cotton fields but no studies have identified potential specific top-down forces that could help manage this pest in the YRZ in China. In order to identify possibilities for managing the cotton aphid, we monitored cotton aphid population dynamics and identified the effect of natural enemies on cotton aphid population growth using various exclusion cages in transgenic Cry1Ac (Bt+CpTI (Cowpea trypsin inhibitor cotton field in 2011. The aphid population growth in the open field (control was significantly lower than those protected or restricted from exposure to natural enemies in the various exclusion cage types tested. The ladybird predator Propylaea japonica Thunberg represented 65% of Coccinellidae predators, and other predators consisted mainly of syrphids (2.1% and spiders (1.5%. The aphid parasitoids Aphidiines represented 76.7% of the total count of the natural enemy guild (mainly Lysiphlebia japonica Ashmead and Binodoxys indicus Subba Rao & Sharma. Our results showed that P. japonica can effectively delay the establishment and subsequent population growth of aphids during the cotton growing season. Aphidiines could also reduce aphid density although their impact may be shadowed by the presence of coccinellids in the open field (likely both owing to resource competition and intraguild predation. The implications of these results are discussed in a framework of the compatibility of transgenic crops and top-down forces exerted by natural enemy guild.

  10. Intercropping With Fruit Trees Increases Population Abundance and Alters Species Composition of Spider Mites on Cotton.

    Science.gov (United States)

    Li, Haiqiang; Pan, Hongsheng; Wang, Dongmei; Liu, Bing; Liu, Jian; Zhang, Jianping; Lu, Yanhui

    2018-05-05

    With the recent increase in planting of fruit trees in southern Xinjiang, the intercropping of fruit trees and cotton has been widely adopted. From 2014 to 2016, a large-scale study was conducted in Aksu, an important agricultural area in southern Xinjiang, to compare the abundance and species composition of spider mites in cotton fields under jujube-cotton, apple-cotton, and cotton monocrop systems. The abundance of spider mites in cotton fields under both intercropping systems was generally higher than in the cotton monocrop. The species composition of spider mites also differed greatly between cotton intercropped with apple or jujube compared to the cotton monocrop. The relative proportion of Tetranychus truncates Ehara (Acari: Tetranychidae) in the species complex generally increased while that of another spider mite, Tetranychus dunhuangensis Wang (Acari: Tetranychidae), decreased under fruit tree-cotton systems. More attention should be paid to the monitoring and management of spider mites, especially T. truncates in this important region of China.

  11. Screening cotton genotypes for seedling drought tolerance

    Directory of Open Access Journals (Sweden)

    Penna Julio C. Viglioni

    1998-01-01

    Full Text Available The objectives of this study were to adapt a screening method previously used to assess seedling drought tolerance in cereals for use in cotton (Gossypium hirsutum L. and to identify tolerant accessions among a wide range of genotypes. Ninety genotypes were screened in seven growth chamber experiments. Fifteen-day-old seedlings were subjected to four 4-day drought cycles, and plant survival was evaluated after each cycle. Three cycles are probably the minimum required in cotton work. Significant differences (at the 0.05 level or lower among entries were obtained in four of the seven experiments. A "confirmation test" with entries previously evaluated as "tolerant" (high survival and "susceptible" (low survival was run. A number of entries duplicated their earlier performance, but others did not, which indicates the need to reevaluate selections. Germplasms considered tolerant included: `IAC-13-1', `IAC-RM4-SM5', `Minas Sertaneja', `Acala 1517E-1' and `4521'. In general, the technique is simple, though time-consuming, with practical value for screening a large number of genotypes. Results from the screening tests generally agreed with field information. The screening procedure is suitable to select tolerant accessions from among a large number of entries in germplasm collections as a preliminary step in breeding for drought tolerance. This research also demonstrated the need to characterize the internal lack of uniformity in growth chambers to allow for adequate designs of experiments.

  12. Bio-oil production from cotton stalk

    International Nuclear Information System (INIS)

    Zheng Jilu; Yi Weiming; Wang Nana

    2008-01-01

    Cotton stalk was fast pyrolyzed at temperatures between 480 deg. C and 530 deg. C in a fluidized bed, and the main product of bio-oil is obtained. The experimental result shows that the highest bio-oil yield of 55 wt% was obtained at 510 deg. C for cotton stalk. The chemical composition of the bio-oil acquired was analyzed by GC-MS, and its heat value, stability, miscibility and corrosion characteristics were determined. These results showed that the bio-oil obtained can be directly used as a fuel oil for combustion in a boiler or a furnace without any upgrading. Alternatively, the fuel can be refined to be used by vehicles. Furthermore, the energy performance of the pyrolysis process was analyzed. In the pyrolysis system used in our experiment, some improvements to former pyrolysis systems are done. Two screw feeders were used to prevent jamming the feeding system, and the condenser is equipped with some nozzles and a heat exchanger to cool quickly the cleaned hot gas into bio-oil

  13. TRACTION RESISTANCE IN CHITOSAN TREATED COTTON

    Directory of Open Access Journals (Sweden)

    LOX Wouter

    2015-05-01

    Full Text Available Nowadays natural products interest has increased. However, when some products are included on textile fibers, they have no affinity and need some binders or other kind of auxiliaries to improve the yeld of the process, and some of them are not so natural as the product which are binding and consequently the “bio” definition is missed as some of them can be considered as highly pollutant. Chitosan is a common used bonding agent for cotton. It improves the antimicrobial and antifungal activity, improves wound healing and is a non-toxic bonding agent. The biopolymer used in this work is chitosan, which is a deacetylated derivative of chitin. These properties depend on the amount of deacetylation (DD and the Molecular weight (MW. Along with these improving properties, as it requires some acid pH to ve solved the treatment with chitosan can have some decreasing mechanical properties. The aim of that paper is to evaluate the change in breaking force of the treated samples and a change in elongation of those samples. It compared different amounts of concentration of chitosan with non treated cotton. The traction resistance test were performed on a dynamometer. The test was conducted according to the UNE EN ISO 13934-1 standard.

  14. Heterosis and correlation in interspecific and intraspecific hybrids of cotton.

    Science.gov (United States)

    Munir, S; Hussain, S B; Manzoor, H; Quereshi, M K; Zubair, M; Nouman, W; Shehzad, A N; Rasul, S; Manzoor, S A

    2016-06-24

    Interspecific and intraspecific hybrids show varying degrees of heterosis for yield and yield components. Yield-component traits have complex genetic relationships with each other. To determine the relationship of yield-component traits and fiber traits with seed cotton yield, six lines (Bt. CIM-599, CIM-573, MNH-786, CIM-554, BH-167, and GIZA-7) and three test lines (MNH-886, V4, and CIM-557) were crossed in a line x tester mating design. Heterosis was observed for seed cotton yield, fiber traits, and for other yield-component traits. Heterosis in interspecific hybrids for seed cotton yield was more prominent than in intraspecific hybrids. The interspecific hybrid Giza-7 x MNH-886 had the highest heterosis (114.77), while among intraspecific hybrids, CIM-554 x CIM-557 had the highest heterosis (61.29) for seed cotton yield. A major trait contributing to seed cotton yield was bolls/plant followed by boll weight. Correlation studies revealed that bolls/plant, boll weight, lint weight/boll, lint index, seed index, lint/seed, staple length, and staple strength were significantly and positively associated with seed cotton yield. Selection based on boll weight, boll number, lint weight/boll, and lint index will be helpful for improving cotton seed yield.

  15. Using atmospheric pressure plasma treatment for treating grey cotton fabric.

    Science.gov (United States)

    Kan, Chi-Wai; Lam, Chui-Fung; Chan, Chee-Kooi; Ng, Sun-Pui

    2014-02-15

    Conventional wet treatment, desizing, scouring and bleaching, for grey cotton fabric involves the use of high water, chemical and energy consumption which may not be considered as a clean process. This study aims to investigate the efficiency of the atmospheric pressure plasma (APP) treatment on treating grey cotton fabric when compared with the conventional wet treatment. Grey cotton fabrics were treated with different combinations of plasma parameters with helium and oxygen gases and also through conventional desizing, scouring and bleaching processes in order to obtain comparable results. The results obtained from wicking and water drop tests showed that wettability of grey cotton fabrics was greatly improved after plasma treatment and yielded better results than conventional desizing and scouring. The weight reduction of plasma treated grey cotton fabrics revealed that plasma treatment can help remove sizing materials and impurities. Chemical and morphological changes in plasma treated samples were analysed by FTIR and SEM, respectively. Finally, dyeability of the plasma treated and conventional wet treated grey cotton fabrics was compared and the results showed that similar dyeing results were obtained. This can prove that plasma treatment would be another choice for treating grey cotton fabrics. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Acoustical evaluation of carbonized and activated cotton nonwovens.

    Science.gov (United States)

    Jiang, N; Chen, J Y; Parikh, D V

    2009-12-01

    An activated carbon fiber nonwoven (ACF) was manufactured from a cotton nonwoven fabric. For the ACF acoustic application, a nonwoven composite of ACF with cotton nonwoven as a base layer was developed. Also produced were the composites of the cotton nonwoven base layer with a layer of glassfiber nonwoven, and the cotton nonwoven base layer with a layer of cotton fiber nonwoven. Their noise absorption coefficients and sound transmission loss were measured using the Brüel and Kjaer impedance tube instrument. Statistical significance of the differences between the composites was tested using the method of Duncan's grouping. The study concluded that the ACF composite exhibited a greater ability to absorb normal incidence sound waves than the composites with either glassfiber or cotton fiber. The analysis of sound transmission loss revealed that the three composites still obeyed the mass law of transmission loss. The composite with the surface layer of cotton fiber nonwoven possessed a higher fabric density and therefore showed a better sound insulation than the composites with glassfiber and ACF.

  17. Correlations and Correlated Responses in Upland Cotton (Gossypium hirsutum L.

    Directory of Open Access Journals (Sweden)

    Echekwu, CA.

    2001-01-01

    Full Text Available Plant breeders must be concerned with the total array of economic characters in their efforts to develop a crop variety acceptable to farmers. Their selection endeavours must therefore take into consideration how changes in one trait affect, simultaneously changes in other economic attributes. The importance of correlations and correlated responses is therefore self evident in plant breeding endeavours. In this study F3 progenies from a cross between two cotton lines SAMCOT-9 x Y422 were evaluated for two years and performance data were used to obtain correlations between nine agronomic and fibre quality traits in upland cotton. The results indicated that plant helght was significantly and positively correlated with seed cotton yield, number of sympodial and monopodial branches, seed index, fibre length and micronaire index. Positive and significant correlations were also obtained between : seed cotton yield, tint percent and fibre strength and fibre length. Significant negative correlations were obtained between : plant height and lint percent ; number of monopodial branches, sympodial branches and lint percent ; fibre length, fibre strength and micronaire index. The correlated responses in the other eight traits when selection was practiced for seed cotton yield in the present study shows that it might be more profitable to practice direct selection for seed cotton yield compared to selecting for seed cotton yield through any of the other traits.

  18. Normalized Tritium Quantification Approach (NoTQA) a Method for Quantifying Tritium Contaminated Trash and Debris at LLNL

    International Nuclear Information System (INIS)

    Dominick, J.L.; Rasmussen, C.L.

    2008-01-01

    characterization method for quantification of tritium contaminated trash and debris. The characterization technique is applicable to surface and subsurface tritium contaminated materials with surfaces amenable to swiping. Some limitations of this characterization technique are identified

  19. Meth Mouth, White Trash, and the Pseudo-Racialization of Methamphetamine Use in the U.S.

    Science.gov (United States)

    Peterson, Jeffery Chaichana; Gubrium, Aline; Fiddian-Green, Alice

    2018-05-07

    Drug scares have historically been created for a range of purposes and with a variety of effects in the United States. Moral panics evoked by these drug scares either support or challenge dominant American ideas about race, economics, and society. In the present study, we examined newspaper accounts of methamphetamine use in the Inland Pacific Northwest of the United States in an effort to understand how the "reality" of the "meth epidemic" is socially constructed in a "meth hotspot," and reflect upon the ways that the discourse of Whiteness intersects with this construction. For our analysis, we are cognizant of the "slipperiness" of the logic of Whiteness as a concept, and the ways that an alternative logic is articulated - one that strategically embraces or distances White drug users to support notions of White dominance. We focus on the possibility that individual meth users could then be portrayed pseudo-racially as "White trash," and thus rendered outside the logic of White racial order. Our findings center on two main themes: (1) the use of fear in the construction of the meth drug scare through the sensationalization of meth, its anthropomorphization, and the depiction of the threat of the White drug user; and (2) how the logic of Whiteness is discursively reconciled within this construction. Given current mediated discourses about drug use and health in the United States that center on the emergence of the White drug user as the face of the opioid crisis, we are well served to carefully consider the recent historical precedence of the "meth epidemic" in which the public was faced with reconciling their views about drug use and the intersection of race, class, and mainstream American identity.

  20. The Optimal Tax on Antebellum U.S. Cotton Exports

    OpenAIRE

    Douglas A. Irwin

    2001-01-01

    The United States produced about 80 percent of the world's cotton in the decades prior to the Civil War. How much monopoly power did the United States possess in the world cotton market and what would have been the effect of an optimal export tax? This paper estimates the elasticity of foreign demand for U.S. cotton exports and uses the elasticity in a simple partial equilibrium model to calculate the optimal export tax and its effect on prices, trade, and welfare. The results indicate that t...

  1. The effect of dendrimer on cotton dyeability with direct dyes

    Directory of Open Access Journals (Sweden)

    Khakzar Bafrooei F.

    2014-01-01

    Full Text Available Pretreatment of cotton fabric with poly(propylene imine dendrimer enhanced its colour strength using C.I. Direct Red 81 and C.I. Direct Blue 78. Application of this dendrimer and the direct dye simultaneously on cotton fabric by the exhaust and the continuous dyeing method were studied; slight improvements in the dyeing results were obtained. Pretreatment of the cotton fabric with dendrimer in an emulsion form using the pad-dry method followed by continuous dyeing markedly increased the colour strength. In addition, level dyeing was obtained, and no negative effects on the fastness properties of the dyes used were observed.

  2. Performance enhancement of a solar still using cotton regenerative medium

    Directory of Open Access Journals (Sweden)

    Thirumalai Gopal Sakthivel

    2017-01-01

    Full Text Available This paper presents the performance of a single slope solar still using cotton cloth regenerative medium. The performance was evaluated under the metrological conditions of Chennai city in India during the summer months of 2016. Two single-slope solar stills are fabricated with an effective area of 0.5 m2 with various thicknesses (2, 4, 6, and 8 mm of cotton cloth were used for the performance comparison. The results showed, the solar still with 6 mm thick cotton assisted regenerative solar still has about 28% improved productivity when compared to conventional solar still.

  3. Desenvolvimento e avaliação de descaroçador para o beneficiamento do algodão Development and evaluation of coring machine for processing cotton seeds

    Directory of Open Access Journals (Sweden)

    Francisco de A. C. Almeida

    2011-06-01

    Full Text Available Desenvolveu-se, através deste trabalho, um descaroçador de 20 serras, visando ao beneficiamento de algodão. As partes constituintes deste descaroçador consistem essencialmente, dos seguintes dispositivos: armação estática (chassi, constituída de duas chapas de ferro de espessura de 6,35 mm, para sustentação dos demais componentes da máquina; uma caixa acumuladora de algodão; câmara de descaroçamento de massa de algodão; dispositivo para regulagem da quantidade de línter; um cilindro composto de 20 serras e um outro de escovas; um condensador; alavanca de deslocamento e acionamento do cilindro descaroçador de discos; um motor elétrico trifásico de 5 CV, 320-220 V para acionamento dos dispositivos de beneficiamento por meio de polias e correias, e chave de partida automática. A avaliação do descaroçador se deu em comparação com as máquinas de 50 e 90 serras, amplamente utilizadas pelas usinas de beneficiamento de algodão no Nordeste brasileiro. O descaroçador desenvolvido responde satisfatoriamente ao beneficiamento do algodão e com desempenho similar ao das máquinas de 50 e 90 serras para todas as características tecnológicas analisadas da fibra no HVI. A melhor eficiência de trabalho do descaroçador de 20 serras foi para a rotação de 344 rpm, com o dispositivo para regulagem de quantidade de línter na posição A e amostra de 600 g.In this study a ginner of 20 saws was developed for processing cotton seeds. The constituent parts of the ginner of 20 saws essentially consist of the following devices: static frame (chassis, consisting of two iron plates of 6.35 mm thickness, for the support of other components of the machine; a box of cotton accumulator; chamber of a mass of cotton ginning; device for regulating the amount of linter; a cylinder composed of 20 saws, another of brushes; a capacitor; gear for shifting and activating the cylinder, ginner discs; a three-phase 5 HP electric motor, 320-220 V to drive

  4. Field evaluation of Bt cotton crop impact on nontarget pests: cotton aphid and boll weevil.

    Science.gov (United States)

    Sujii, E R; Togni, P H B; de A Ribeiro, P; de A Bernardes, T; Milane, P V G N; Paula, D P; Pires, C S S; Fontes, E M G

    2013-02-01

    Bt cotton plants expressing Cry1Ac protein have high specificity for the control of lepidopteran larvae. However, studies conducted in several countries have shown these plants have a differential impact on nontarget herbivores. The aim of this study was to compare the colonization rates and population abundance of the cotton aphid, Aphis gossypii Glover (Hemiptera: Aphididae) and the boll weevil, Anthonomus grandis Boheman (Coleoptera: Curculionidae), in plots of Bt (Nuopal) and non-Bt cotton (Delta Opal) in an experimental field in Brasilia, DF, Brazil. No difference was observed in the preference and colonization by winged aphids to plants from the two treatments. There was no significant difference in abundance of wingless aphids or in the production of winged aphids between treatments. Apparently, the parameters that control factors such as fecundity, survival, and dispersal were similar on both Bt and non-Bt plants. Monitoring of plants for coccinellids, a specialist predator of aphids, and ants that act on the dispersal of aphids among plants showed no significant difference between Bt and non-Bt plants, supporting the inference above. Regarding the effect on boll weevil, there was also no significant difference between treatments in the total number of fruiting structures attacked in each plot, the percentage of fruiting structures attacked per plant or on the number of weevils emerging from fruits with boll weevil damage from egg-laying, when damaged fruit samples were held in the laboratory. Based on these results, we conclude that there is no impact of Bt cotton crop expressing Cry1Ac on the nontarget herbivores tested under field conditions.

  5. Molecular and Biochemical Characterization of Cotton Epicuticular Wax in Defense Against Cotton Leaf Curl Disease.

    Science.gov (United States)

    Khan, Muhammad Azmat Ullah; Shahid, Ahmad Ali; Rao, Abdul Qayyum; Bajwa, Kamran Shehzad; Samiullah, Tahir Rehman; Muzaffar, Adnan; Nasir, Idrees Ahmad; Husnain, Tayyab

    2015-12-01

    Gossypium arboreumis resistant to Cotton leaf curl Burewala virus and its cognate Cotton leaf curl Multan beta satellite ( CLCuBuV and CLCuMB ). However, the G. arboreum wax deficient mutant (GaWM3) is susceptible to CLCuV . Therefore, epicuticular wax was characterized both quantitatively and qualitatively for its role as physical barrier against whitefly mediated viral transmission and co-related with the titer of each viral component (DNA-A, alphasatellite and betasatellite) in plants. The hypothesis was the CLCuV titer in cotton is dependent on the amount of wax laid down on plant surface and the wax composition. Analysis of the presence of viral genes, namely alphasatellite, betasatellite and DNA-A, via real-time PCR in cotton species indicated that these genes are detectable in G. hirsutum , G. harknessii and GaWM3, whereas no particle was detected in G. arboreum . Quantitative wax analysis revealed that G. arboreum contained 183 μg.cm -2 as compared to GaWM3 with only 95 μg.cm -2 . G. hirsutum and G. harknessii had 130 μg.cm -2 and 146 μg.cm -2 , respectively. The GCMS results depicted that Lanceol, cis was 45% in G. harknessii . Heptadecanoic acid was dominant in G. arboreum with 25.6%. GaWM3 had 18% 1,2,-Benenedicarboxylic acid. G. hirsutum contained 25% diisooctyl ester. The whitefly feeding assay with Nile Blue dye showed no color in whiteflies gut fed on G. arboreum . In contrast, color was observed in the rest of whiteflies. From results, it was concluded that reduced quantity as well as absence of (1) 3-trifluoroacetoxytetradecane, (2) 2-piperidinone,n-|4-bromo-n-butyl|, (3) 4-heptafluorobutyroxypentadecane, (4) Silane, trichlorodocosyl-, (5) 6- Octadecenoic acid, methyl ester, and (6) Heptadecanoicacid,16-methyl-,methyl ester in wax could make plants susceptible to CLCuV , infested by whiteflies.

  6. DeepCotton: in-field cotton segmentation using deep fully convolutional network

    Science.gov (United States)

    Li, Yanan; Cao, Zhiguo; Xiao, Yang; Cremers, Armin B.

    2017-09-01

    Automatic ground-based in-field cotton (IFC) segmentation is a challenging task in precision agriculture, which has not been well addressed. Nearly all the existing methods rely on hand-crafted features. Their limited discriminative power results in unsatisfactory performance. To address this, a coarse-to-fine cotton segmentation method termed "DeepCotton" is proposed. It contains two modules, fully convolutional network (FCN) stream and interference region removal stream. First, FCN is employed to predict initially coarse map in an end-to-end manner. The convolutional networks involved in FCN guarantee powerful feature description capability, simultaneously, the regression analysis ability of neural network assures segmentation accuracy. To our knowledge, we are the first to introduce deep learning to IFC segmentation. Second, our proposed "UP" algorithm composed of unary brightness transformation and pairwise region comparison is used for obtaining interference map, which is executed to refine the coarse map. The experiments on constructed IFC dataset demonstrate that our method outperforms other state-of-the-art approaches, either in different common scenarios or single/multiple plants. More remarkable, the "UP" algorithm greatly improves the property of the coarse result, with the average amplifications of 2.6%, 2.4% on accuracy and 8.1%, 5.5% on intersection over union for common scenarios and multiple plants, separately.

  7. Conductive Cotton Fabrics for Motion Sensing and Heating Applications

    Directory of Open Access Journals (Sweden)

    Mengyun Yang

    2018-05-01

    Full Text Available Conductive cotton fabric was prepared by coating single-wall carbon nanotubes (CNTs on a knitted cotton fabric surface through a “dip-and-dry” method. The combination of CNTs and cotton fabric was analyzed using scanning electron microscopy (SEM and Raman scattering spectroscopy. The CNTs coating improved the mechanical properties of the fabric and imparted conductivity to the fabric. The electromechanical performance of the CNT-cotton fabric (CCF was evaluated. Strain sensors made from the CCF exhibited a large workable strain range (0~100%, fast response and great stability. Furthermore, CCF-based strain sensors was used to monitor the real-time human motions, such as standing, walking, running, squatting and bending of finger and elbow. The CCF also exhibited strong electric heating effect. The flexible strain sensors and electric heaters made from CCF have potential applications in wearable electronic devices and cold weather conditions.

  8. Assessment of Bollgard II cotton pollen mediated transgenes flow to ...

    African Journals Online (AJOL)

    INERA05

    2013-08-14

    Aug 14, 2013 ... insects such as honey bees, bumble bees and butterflies. Genetic materials ... cotton fields separated from the transgenes source by wide open space. In Boni ..... Breeding: new strategies in plant improvement. International ...

  9. Bleaching of hydroentangled greige cotton nonwoven fabrics without scouring

    Science.gov (United States)

    This work investigated whether a hydroentangled greige cotton nonwoven fabric made at a relatively high hydroentangling water pressure, say, 135-bar, could be successfully bleached to attain the desired whiteness, absorbency and other properties without traditional scouring. Accordingly, the scoured...

  10. Aerial electrostatic spray deposition and canopy penetration in cotton

    Science.gov (United States)

    Spray deposition on abaxial and adaxial leaf surfaces along with canopy penetration are essential for insect control and foliage defoliation in cotton production agriculture. Researchers have reported that electrostatically charged sprays have increased spray deposit onto these surfaces under widel...

  11. Teste GIN: detecção de gap em crianças com desvio fonológico Noise test: gap detection in children with phonological deviation

    Directory of Open Access Journals (Sweden)

    Elaine Feltre Assis

    2012-01-01

    Full Text Available OBJETIVO: investigar a resolução temporal: detecção de gaps em crianças com desvios fonológicos por meio do teste GIN e relacionar o grau do desvio fonológico com desempenho no teste GIN. MÉTODO: 6 indivíduos, de ambos os gêneros, 5 meninos e 1 menina, com idade entre 10 e 11 anos, com diagnóstico de desvio fonológico, em atendimento na clínica-escola do curso de Fonoaudiologia da FEAD de Belo Horizonte/MG, todos com ausência de perda auditiva e problemas neurológicos e/ou cognitivos. Os participantes foram submetidos ao Teste GIN, em intensidade de 50dB acima do limiar. RESULTADOS: das 06 crianças avaliadas, 5 (83,33% encontram-se alteradas e apenas 1 (16,67% obteve valores dentro do padrão de normalidade. Apesar da pequena amostra, viu-se que 83,33% das crianças com desvio fonológico tiveram limiares do GIN aquém do esperado para faixa etária. Porém não foi possível estabelecer uma relação direta entre grau de classificação do desvio fonológico e o baixo desempenho obtido no teste GIN, no qual apenas 1 criança com desvio médio moderado apresentou pior desempenho no teste GIN. CONCLUSÃO: crianças com desvio fonológico podem apresentar alteração no processamento temporal.PURPOSE: to investigate the temporal resolution, as for: gaps detection in children with phonological deviation through noise test and related with the degree of phonological performance in noise test. METHOD: 6 patients of both genders, five boys and one girl, aged between 10 and 11 year-old with phonological disorder' diagnosis in attendance at the school clinic of the Speech Therapy course (FEAD Belo Horizonte / MG, all with no hearing loss and no neurological and / or cognitive problems. The subjects underwent the GIN test at intensity of 50dB above the threshold. RESULTS: from the 6 evaluated children, 5 (83.33% had abnormal responses at gin test and only one (16.67% had values within the normal range. Despite the small sample, it was

  12. Teste GIN: detecção de gap em crianças com desvio fonológico Noise test: gap detection in children with phonological deviation

    Directory of Open Access Journals (Sweden)

    Elaine Feltre Assis

    2013-02-01

    Full Text Available OBJETIVO: investigar a resolução temporal: detecção de gaps em crianças com desvios fonológicos por meio do teste GIN e relacionar o grau do desvio fonológico com desempenho no teste GIN. MÉTODO: 6 indivíduos, de ambos os gêneros, 5 meninos e 1 menina, com idade entre 10 e 11 anos, com diagnóstico de desvio fonológico, em atendimento na clínica-escola do curso de Fonoaudiologia da FEAD de Belo Horizonte/MG, todos com ausência de perda auditiva e problemas neurológicos e/ou cognitivos. Os participantes foram submetidos ao Teste GIN, em intensidade de 50dB acima do limiar. RESULTADOS: das 06 crianças avaliadas, 5 (83,33% encontram-se alteradas e apenas 1 (16,67% obteve valores dentro do padrão de normalidade. Apesar da pequena amostra, viu-se que 83,33% das crianças com desvio fonológico tiveram limiares do GIN aquém do esperado para faixa etária. Porém não foi possível estabelecer uma relação direta entre grau de classificação do desvio fonológico e o baixo desempenho obtido no teste GIN, no qual apenas 1 criança com desvio médio moderado apresentou pior desempenho no teste GIN. CONCLUSÃO: crianças com desvio fonológico podem apresentar alteração no processamento temporal.PURPOSE: to investigate the temporal resolution, as for: gaps detection in children with phonological deviation through noise test and related with the degree of phonological performance in noise test. METHOD: 6 patients of both genders, five boys and one girl, aged between 10 and 11 year-old with phonological disorder' diagnosis in attendance at the school clinic of the Speech Therapy course (FEAD Belo Horizonte / MG, all with no hearing loss and no neurological and / or cognitive problems. The subjects underwent the GIN test at intensity of 50dB above the threshold. RESULTS: from the 6 evaluated children, 5 (83.33% had abnormal responses at gin test and only one (16.67% had values within the normal range. Despite the small sample, it was

  13. Remote sensing techniques for monitoring the Rio Grande Valley cotton stalk destruction program

    Energy Technology Data Exchange (ETDEWEB)

    Richardson, A.J.; Gerbermann, A.H.; Summy, K.R.; Anderson, G.L. (Department of Agriculture, Weslaco, TX (United States))

    1993-09-01

    Post harvest cotton (Gossypium hirsutum L.) stalk destruction is a cultural practice used in the Rio Grande Valley to suppress over wintering populations of boll weevils (Anthonomus grandis Boheman) without using chemicals. Consistent application of this practice could substantially reduce insecticide usage, thereby minimizing environmental hazards and increasing cotton production profits. Satellite imagery registered within a geographic information system was used to monitor the cotton stalk destruction program in the Rio Grande Valley. We found that cotton stalk screening procedures based on standard multispectral classification techniques could not reliably distinguish cotton from sorghum. Greenness screening for cotton plant stalks after the stalk destruction deadline was possible only where ground observations locating cotton fields were available. These findings indicate that a successful cotton stalk destruction monitoring program will require satellite images and earth referenced data bases showing cotton field locations.

  14. Study of gene flow from GM cotton (Gossypium hirsutum) varieties in El Espinal (Tolima, Colombia)

    International Nuclear Information System (INIS)

    Rache Cardenal, Leidy Yanira; Mora Oberlaender, Julian; Chaparro Giraldo, Alejandro

    2013-01-01

    In 2009, 4088 hectares of genetically modified (GM) cotton were planted in Tolima (Colombia), however there is some uncertainty about containment measures needed to prevent the flow of pollen and seed from regulated GM fields into adjacent fields. In this study, the gene flow from GM cotton varieties to conventional or feral cotton plants via seed and pollen was evaluated. ImmunostripTM, PCR and ELISA assays were used to detect gene flow. Fifty six refuges, 27 fields with conventional cotton and four feral individuals of the enterprise Remolinos Inc. located in El Espinal (Tolima) were analyzed in the first half of 2010. The results indicated seed mediated gene flow in 45 refuges (80.4 %) and 26 fields with conventional cotton (96 %), besides pollen mediated gene flow in one field with conventional cotton and nine refuges. All fields cultivated with conventional cotton showed gene flow from GM cotton. Two refuges and two feral individuals did not reveal gene flow from GM cotton.

  15. Utilization of cotton waste for regenerated cellulose fibres: Influence of degree of polymerization on mechanical properties.

    Science.gov (United States)

    De Silva, Rasike; Byrne, Nolene

    2017-10-15

    Cotton accounts for 30% of total fibre production worldwide with over 50% of cotton being used for apparel. In the process from cotton bud to finished textile product many steps are required, and significant cotton waste is generated. Typically only 30% of pre consumer cotton is recycled. Here we use cotton waste lint to produce regenerated cellulose fibres (RCF). We find the RCF from waste cotton lint had increased mechanical properties compared to RCF produced from wood pulp. We show that this is likely linked to the higher degree of polymerization (DP) of waste cotton lint. An ionic liquid is used to dissolve the cotton lint and the rheology of the spinning is measured. The properties of the RCF are characterized and compared to wood pulp RCF. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Evaluation of vinasse/aqua ammonia mixture applied to soil fertilization in sugar cane areas harvested lacking sugar cane trash without prior burning: losses of NH3 by volatilization and 15 N recovery

    International Nuclear Information System (INIS)

    Oliveira, M.W.; Trivelin, P.C.O.; Bendassolli, J.A.; Muraoka, T.

    1997-01-01

    The present work aimed to evaluate the losses of NH 3 by volatization, from the vinasse/aqua ammonia mixture and urea solution applied to the soil. The N dose applied for both sources was 80 Kg ha -1 , with the volume of vinasse and urea solution applied to the surface being 200 and 100 m 3 , respectively. The nitrogen sources were applied to soil covered or not by sugarcane trash. A semi-opened static collector device was used to evaluate the ammonia volatization. The isotopic technique with 15 N was used to quantify the N recovered in the soil from the nitrogen sources applied in microplots. These microplots consisted of 96 mm-diameter PVC cylinders which were buried in the soil at 200 mm. The results show that the volatization of ammonia from the vinasse/aqua ammonia mixture, applied to the soil covered or not by sugarcane trash, ranged from 5 to 7% of the N applied. These results were similar to those observed in the treatment where urea solution was applied to the soil lacking sugarcane trash, but lower when compared to the urea applied to the soil covered with trash confirmed the volatization results, with the least 15 N recovery (57%) being obtained in this treatment. In the other treatments, i.e. urea applied to soil lacking sugarcane trash; aqua annonia/vinasse mixture applied to soil covered or not with sugarcane trash, the mean recovery of 15 N were 60.2; 70.6 and 74.2 % respectively. These results support the recommendation of the use of a fluid mixture for nitrogen fertilization in ratoon cane areas after the mechanized sugarcane harvest without prior burning. (author). 15 refs., 1 fig., 1 tab

  17. Sustainability in the supply chain of organic cotton

    OpenAIRE

    Retamiro, Wiliam; Silva, José Luis Gomes da; Vieira, Edson Trajano

    2013-01-01

    This article aims to diagnose the application of sustainability concepts in the economic, spatial,ecological, social, cultural and politics in the productive chain of cotton. Explains about the cotton industry is free from all pesticides and their use in the textile production chain, increasing the value of the input, as well as products derived from this. Analyzed by the method of case studywith a qualitative approach in a bibliographic and documentary through to the collection of data,their...

  18. Biological Innovation and Productivity Growth in the Antebellum Cotton Economy

    OpenAIRE

    Alan L. Olmstead; Paul W. Rhode

    2008-01-01

    The Cliometrics literature on slave efficiency has generally focused on static questions. We take a decidedly more dynamic approach. Drawing on the records of 142 plantations with 509 crops years, we show that the average daily cotton picking rate increased about four-fold between 1801 and 1862. We argue that the development and diffusion of new cotton varieties were the primary sources of the increased efficiency. These finding have broad implications for understanding the South's preeminenc...

  19. Cycling of fertilizer and cotton crop residue nitrogen

    International Nuclear Information System (INIS)

    Rochester, I.J.; Constable, G.A.; MacLeod, D.A.

    1993-01-01

    Mineral nitrogen (N), nitrate and ammonium contents were monitored in N-fertilized soils supporting cotton crops to provide information on the nitrification, mineralization and immobilization processes operating in the soil. The relative contributions of fertilizer N, previous cotton crop residue N and indigenous soil N to the mineral N pools and to the current crop's N uptake were calculated. After N fertilizer (urea) application, the soil's mineral N content rose rapidly and subsequently declined at a slower rate. The recovery of 15 N-labelled urea as mineral N declined exponentially with time. Biological immobilization (and possibly denitrification to some extent) were believed to be the major processes reducing post-application soil mineral N content. Progressively less N was mineralized upon incubation of soil sampled through the growing season. Little soil N (either from urea or crop residue) was mineralized at crop maturity. Cycling of N was evident between the soil mineral and organic N pools throughout the cotton growing season. Considerable quantities of fertilizer N were immobilized by the soil micro biomass; immobilized N was remineralized and subsequently taken up by the cotton crop. A large proportion of the crop N was taken up in the latter part of the season when the soil mineral N content was low. It is suggested that much of the N taken up by cotton was derived from microbial sources, rather than crop residues. The application of cotton crop residue (stubble) slightly reduced the mineral N content in the soil by encouraging biological immobilization. 15 N was mineralized very slowly from the labelled crop residue and did not contribute significantly to the supply of N to the current crop. Recovery of labelled fertilizer N and labelled crop residue N by the cotton crop was 28% and 1%, respectively. In comparison, the apparent recovery of fertilizer N was 48%. Indigenous soil N contributed 68% of the N taken up by the cotton crop. 33 refs., 1 tab

  20. Genomic studies for drought tolerance in cotton (abstract)

    International Nuclear Information System (INIS)

    Mahboob-ur-Rehman; Ullah, I.; Asir, M.; Zafar, Y.; Malik, K.A.

    2005-01-01

    The cotton germplasm developed in Pakistan has not been screened comprehensively for their response to water stress, which is a pre-requisite in exploring different metabolic pathways, development of genome maps, isolation of genes etc. The objectives of the study were to identify drought tolerant/sensitive cotton genotypes, development of genetic linkage maps, and to identify the most robust DNA markers leading towards marker-assisted selection (MAS). A field trial was conducted to investigate variation in gas exchange parameters and productivity traits in 32 cotton cultivars/promising strains under water stress environment and to ascertain association among these physiological and productivity traits. Photosynthetic rate (P), stomatal conductance (gs) and transpiration rate (E) were significantly reduced under water stress. Substantial genotypic variation for gas exchange parameters especially photosynthetic rate were observed with a significant association with productivity traits under water-limited environment elucidating its use as an indirect selection criterion for seed cotton yield. Moreover, the genotypes FH-901 and CIM-1100 were found the most sensitive and tolerant cultivars, respectively. Four hundred eighty random primers were surveyed on different cotton genotypes involved in population development programs. Out of these, 32 polymorphic primers were identified which are being converted into sequence characterized amplified regions (SCARs). Similarly, 25 out of 150 microstatellite loci (SSRs) were polymorphic among the cotton genotypes. Amplified fragment length polymorphism (AFLP) fingerprinting technique is being exploited to search for additional polymorphisms. The study will have impact on cotton breeding programme by reducing span to develop drought tolerant cotton varieties. (author)

  1. Study on Bleaching Technology of Cotton Fabric with Sodium Percarbonate

    OpenAIRE

    Li Zhi; Wang Yanling; Wang Zhichao

    2016-01-01

    Bleach cotton fabric with sodium percarbonate solution. Analyse of the effect of the concentration of sodium percarbonate solution, bleaching time, bleaching temperature and the light radiation on the bleaching effect of fabric.The result shows that increasing concentrations of percarbonate,increasing the bleaching time , raising the bleaching temperature and the UV irradiation may whiten the cotton fabric.The most suitable conditions for the bleaching process is concentration of sodium perca...

  2. Elemental analysis of cotton by laser-induced breakdown spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Schenk, Emily R.; Almirall, Jose R.

    2010-05-01

    Laser-induced breakdown spectroscopy (LIBS) has been applied to the elemental characterization of unprocessed cotton. This research is important in forensic and fraud detection applications to establish an elemental fingerprint of U.S. cotton by region, which can be used to determine the source of the cotton. To the best of our knowledge, this is the first report of a LIBS method for the elemental analysis of cotton. The experimental setup consists of a Nd:YAG laser that operates at the fundamental wavelength as the LIBS excitation source and an echelle spectrometer equipped with an intensified CCD camera. The relative concentrations of elements Al, Ba, Ca, Cr, Cu, Fe, Mg, and Sr from both nutrients and environmental contributions were determined by LIBS. Principal component analysis was used to visualize the differences between cotton samples based on the elemental composition by region in the U.S. Linear discriminant analysis of the LIBS data resulted in the correct classification of >97% of the cotton samples by U.S. region and >81% correct classification by state of origin.

  3. Textile industry can be less pollutant: introducing naturally colored cotton

    Directory of Open Access Journals (Sweden)

    Solimar Garcia

    2014-07-01

    Full Text Available 800x600 Studies in agribusiness and textile industry, both involved with the production of manufacturing fashion present insufficient development for new products that could represent water savings and reduction of chemical effluents, making this production chain a sustainable business. This paper introduces the colored and organic cotton as an alternative to foster colored cotton producing farmers and improving the concept of sustainability in the textile sector. Results show that the increase in the production of colored and organic cotton, may result in reduction of water use, and consequent reduction in the disposal of effluents in nature. As the colored and organic cotton is produced by small farmers, governmental agencies need to participate in the effort of improving its production and distribution, providing the needed infrastructure to meet the increasing market. This would slowly encourage the reduction of white cotton consumption in exchange for this naturally colored product. The water used, and consequent polluted discharge in the use of colored cotton in the textile industry might be reduced by 70%, assuming a reduction of environmental impact of 5% per year would represent expressive numbers in the next ten years. Normal 0 21 false false false ES X-NONE X-NONE

  4. Asymmetric evolution and domestication in allotetraploid cotton (Gossypium hirsutum L.

    Directory of Open Access Journals (Sweden)

    Lei Fang

    2017-04-01

    Full Text Available Polyploidy plays a major role in genome evolution, which corresponds to environmental changes over millions of years. The mechanisms of genome evolution, particularly during the process of domestication, are of broad interest in the fields of plant science and crop breeding. Upland cotton is derived from the hybridization and polyploidization of its ancient A and D diploid ancestors. As a result, cotton is a model for polyploid genome evolution and crop domestication. To explore the genomic mysteries of allopolyploid cotton, we investigated asymmetric evolution and domestication in the A and D subgenomes. Interestingly, more structural rearrangements have been characterized in the A subgenome than in the D subgenome. Correspondingly, more transposable elements, a greater number of lost and disrupted genes, and faster evolution have been identified in the A subgenome. In contrast, the centromeric retroelement (RT-domain related sequence of tetraploid cotton derived from the D subgenome progenitor was found to have invaded the A subgenome centromeres after allotetrapolyploid formation. Although there is no genome-wide expression bias between the subgenomes, as with expression-level alterations, gene expression bias of homoeologous gene pairs is widespread and varies from tissue to tissue. Further, there are more positively selected genes for fiber yield and quality in the A subgenome and more for stress tolerance in the D subgenome, indicating asymmetric domestication. This review highlights the asymmetric subgenomic evolution and domestication of allotetraploid cotton, providing valuable genomic resources for cotton research and enhancing our understanding of the basis of many other allopolyploids.

  5. Fabrication of superhydrophobic cotton fabrics using crosslinking polymerization method

    Science.gov (United States)

    Jiang, Bin; Chen, Zhenxing; Sun, Yongli; Yang, Huawei; Zhang, Hongjie; Dou, Haozhen; Zhang, Luhong

    2018-05-01

    With the aim of removing and recycling oil and organic solvent from water, a facile and low-cost crosslinking polymerization method was first applied on surface modification of cotton fabrics for water/oil separation. Micro-nano hierarchical rough structure was constructed by triethylenetetramine (TETA) and trimesoyl chloride (TMC) that formed a polymeric layer on the surface of the fabric and anchored Al2O3 nanoparticles firmly between the fabric surface and the polymer layer. Superhydrophobic property was further obtained through self-assembly grafting of hydrophobic groups on the rough surface. The as-prepared cotton fabric exhibited superoleophilicity in atmosphere and superhydrophobicity both in atmosphere and under oil with the water contact angle of 153° and 152° respectively. Water/oil separation test showed that the as-prepared cotton fabric can handle with various oil-water mixtures with a high separation efficiency over 99%. More importantly, the separation efficiency remained above 98% over 20 cycles of reusing without losing its superhydrophobicity which demonstrated excellent reusability in oil/water separation process. Moreover, the as-prepared cotton fabric possessed good contamination resistance ability and self-cleaning property. Simulation washing process test showed the superhydrophobic cotton fabric maintained high value of water contact angle above 150° after 100 times washing, indicating great stability and durability. In summary, this work provides a brand-new way to surface modification of cotton fabric and makes it a promising candidate material for oil/water separation.

  6. Cotton leaf curl Burewala virus with intact or mutant transcriptional activator proteins: complexity of cotton leaf curl disease.

    Science.gov (United States)

    Kumar, Jitendra; Gunapati, Samatha; Alok, Anshu; Lalit, Adarsh; Gadre, Rekha; Sharma, Naresh C; Roy, Joy K; Singh, Sudhir P

    2015-05-01

    Cotton leaf curl disease (CLCuD) is a serious disease of cotton on the Indian subcontinent. In the present study, three cotton leaf curl viruses, cotton leaf curl Burewala virus (CLCuBuV), cotton leaf curl Kokhran virus (CLCuKoV) and cotton leaf curl Multan virus (CLCuMV), and their associated satellites, cotton leaf curl Multan betasatellite (CLCuMB) and cotton leaf curl Multan alphasatellite (CLCuMA), were detected. CLCuBuV with either intact (CLCuBuV-1) or mutant (CLCuBuV-2) transcriptional activator protein (TrAP) were detected in different plants. Agroinoculation with CLCuBuV-1 or CLCuBuV-2 together with CLCuMB and CLCuMA, resulted in typical leaf curling and stunting of tobacco plants. Inoculation with CLCuKoV or an isolate of CLCuMV (CLCuMV-2), together with CLCuMB and CLCuMA, induced severe leaf curling, while the other isolate of CLCuMV (CLCuMV-1), which was recombinant in origin, showed mild leaf curling in tobacco. To investigate the effect of intact or mutant TrAP and also the recombination events, CLCuBuV-1, CLCuBuV-2, CLCuMV-1 or CLCuMV-2 together with the satellites (CLCuMA and CLCuMB) were transferred to cotton via whitefly-mediated transmission. Cotton plants containing CLCuBuV-1, CLCuBuV-2 or CLCuMV-2 together with satellites showed curling and stunting, whereas the plants having CLCuMV-1 and the satellites showed only mild and indistinguishable symptoms. CLCuBuV-1 (intact TrAP) showed severe symptoms in comparison to CLCuBuV-2 (mutant TrAP). The present study reveals that two types of CLCuBuV, one with an intact TrAP and the other with a mutant TrAP, exist in natural infection of cotton in India. Additionally, CLCuMuV-1, which has a recombinant origin, induces mild symptoms in comparison to the other CLCuMV isolates.

  7. Understanding the relationship between cotton fiber properties and non-cellulosic cell wall polysaccharides

    DEFF Research Database (Denmark)

    Rajasundaram, Dhivyaa; Runavot, Jean-Luc; Guo, Xiaoyuan

    2014-01-01

    cotton fibers, which are of both biological and industrial importance. To this end, we attempted to study cotton fiber characteristics together with glycan arrays using regression based approaches. Taking advantage of the comprehensive microarray polymer profiling technique (CoMPP), 32 cotton lines from...... different cotton species were studied. The glycan array was generated by sequential extraction of cell wall polysaccharides from mature cotton fibers and screening samples against eleven extensively characterized cell wall probes. Also, phenotypic characteristics of cotton fibers such as length, strength...

  8. Postcards from the edge: Trash-2-Cash communication tools used to support inter-disciplinary work towards a design driven material innovation (DDMI) methodology

    Science.gov (United States)

    Earley, R.; Hornbuckle, R.

    2017-10-01

    In this paper postcards from the EU funded Horizon 2020 Trash-2-Cash (2015-2018) project - completed by workshop participants - are presented in three tables with a focus on how they contributed to the building of communication channels, shared understanding and methods in this inter-disciplinary consortium work. The Trash-2-Cash project aims to support better waste utilisation, improve material efficiency, contribute to reduction of landfill area needs, whilst also producing high-value commercial products. Novel materials will drive the generation of new textile fibres that will utilize paper and textile fibre waste, originating from continuously increasing textile consumption. The inter-disciplanarity of the participants is key to achieving the project aims - but communication between sectors is challenging due to diverse expertise and levels of experience; language and cultural differences can also be barriers to collaboration as well. Designing easy and accessible, even fun, communication tools are one of the ways to help build relationships. The cards reviewed were used in Prato (November 2015), Helsinki (February 2016) and London (November 2016). This paper concludes with insights for the ongoing development of the project communications work towards the Design Driven Material Innovation (DDMI) methodology, due to be presented at the end of the project in 2018.

  9. Avaliação da qualidade de vida em funcionários praticantes de ginástica holística em empresa

    OpenAIRE

    Fernanda Fonseca dos Santos Lopes; Zelia Zilda Lourenço de Camargo Bittencourt

    2012-01-01

    Introdução: A qualidade de vida na empresa é um importante recurso de promoção de saúde, e pode ser desenvolvida a partir da pratica de atividades físicas. O exercício físico é uma forma de lazer e de restaurar a saúde dos efeitos da rotina estressante do trabalho, proporcionando condições de melhor desempenho e produtividade. A Ginástica Holística atua através da sensibilização e da tomada de consciência, de modo a levar o sujeito a uma melhor utilização do seu potencial perceptivo, sensoria...

  10. Avaliação dos benefícios da ginástica localizada sobre a postura e a flexibilidade de mulheres na terceira idade

    OpenAIRE

    Lima,Hélia Cristina Oliveira; Aguiar,Jaina Bezerra de; Paredes,Paulo Fernando Machado; Gurgel,Luilma Albuquerque

    2010-01-01

    Desvios posturais e redução na flexibilidade são alterações observadas com o avançar da idade, podendo desencadear dor e dificuldades de movimentação. Este estudo buscou avaliar a influência de um programa de ginástica, de dois meses de duração, sobre a postura e flexibilidade de idosas institucionalizadas (n = 10, 60-75 anos). A postura foi avaliada através do uso de simetrógrafo, fotografias e do teste de equilíbrio sagital pélvico, e a flexibilidade através do teste de sentar e alcançar. C...

  11. Extensionando “saúdes”, produzindo sociabilidades: o projeto "ginástica para comunidade" da Universidade Federal do Rio Grande

    OpenAIRE

    Freitas, Gustavo da Silva; Nunes, Giovana Valente; Teixeira, Juliana Cotting

    2014-01-01

    Trabalho apresentado no 31º SEURS - Seminário de Extensão Universitária da Região Sul, realizado em Florianópolis, SC, no período de 04 a 07 de agosto de 2013 - Universidade Federal de Santa Catarina. O Projeto “Ginástica para a Comunidade” está em ação há mais de dezesseis anos tendo sido criado por iniciativa de professores de Educação Física da Universidade Federal do Rio Grande (FURG), motivados em se integrar à comunidade numa ação de extensão. Com diferentes propósitos e formatos ao ...

  12. Tensile Properties of Single Jersey and 1×1 Rib Knitted Fabrics Made from 100% Cotton and Cotton/Lycra Yarns

    Directory of Open Access Journals (Sweden)

    Dereje Berihun Sitotaw

    2017-01-01

    Full Text Available The tensile properties such as tensile strength which is measured as breaking force in Newton (N and elongation percent (% at break of single jersey and 1×1 rib (knitted with full needles knitted fabrics made from 100% cotton and cotton/Lycra yarns (5% Lycra yarn content in 95% combed cotton yarn are investigated in this research. The sample fabrics are conditioned for 24 hours at 20±1°C temperature and 65±2% relative humidity before testing. Ten specimens (five for lengthwise and five for widthwise have been taken from each of the two knitted structures, those made from 100% cotton and cotton/Lycra (at 95/5 percent ratio blend yarns. According to the discussion and as found from the investigations, the tensile properties of single jersey and 1×1 rib knitted fabrics made from 100% cotton and cotton/Lycra yarns are significantly different from each other and both of the knitted fabrics have high elongation percent at break with cotton/Lycra blend yarns as compared to 100% cotton yarn. Knitted fabrics made from cotton/Lycra blended yarn have low breaking force and high elongation percent at break relative to knitted fabrics made from 100% cotton yarns.

  13. CORRELACIONES Y ANÁLISIS DE SENDERO EN ALGODÓN (Gossypium hirsutum L. EN EL CARIBE COLOMBIANO CORRELATIONS AND PATH ANALYSIS IN COTTON (Gossypium hirsutum L. IN THE COLOMBIAN CARIBBEAN

    Directory of Open Access Journals (Sweden)

    Miguel Mariano Espitia Camacho

    2008-06-01

    Full Text Available El cultivo del algodón es la principal actividad agrícola en la economía del Caribe colombiano en el segundo semestre del año y el principal abastecedor de fibra a la industria nacional desde hace aproximadamente 60 años. El objetivo de este trabajo fue estimar las correlaciones fenotípicas, genéticas y ambientales, entre 11 caracteres agronómicos y realizar un análisis de sendero para rendimiento de fibra. Se utilizaron los datos de la evaluación agronómica de 10 genotipos de algodón en ocho ambientes del Caribe colombiano. En cada ambiente se utilizó un diseño experimental de bloques completos al azar con cuatro repeticiones. Los resultados indicaron que las correlaciones genéticas fueron superiores a las fenotípicas y ambientales. El rendimiento de fibra (REF presentó las mayores correlaciones fenotípicas, genéticas y fenotipicas parciales con el porcentaje de fibra (PFI, el rendimiento de algodón - semilla (RAS y el peso de mota (PMO, con valores de r > 0,43 (PThe cotton crop is the main agricultural activity in the economy of the colombian Caribbean in the second semester of the year and the main supplier of fibre to national industry for about 60 years. The objective of this work was to estimate the phenotypic, genetic and environmental correlations, between 11 agronomic characters and to make a path analysis for fibre yield. Data of agronomic evaluation of 10 genotypes of cotton in eight environments of the colombian Caribbean were used. In each environment experimental design at random complete blocks with four repetitions were used. The results indicated that genetic correlations were superior to phenotypic and environmental correlations. Fibre yield (FIY presented the highest phenotypic, genetic and partial phenotypic correlations with ginning percentage (GP, seed-cotton yield (SCY and boll weight (BOW with values of r > 0,43 (P<0,01. The FIP (0,810 was the cause variable that showed the greatest direct effect on

  14. Exploring potential and opportunities for pakistan cotton export

    International Nuclear Information System (INIS)

    Afridi, G. S.; Tariq, S. A.

    2016-01-01

    Agriculture is the single largest shareholder to GDP an employment to labour force. It has major share in export but unfortunately unable to meet international standards. This study aims to analyze the pattern of Pakistan cotton export, and to explore sector's export potential and opportunities. This new research endeavor with well-tested analytical tools enabled the trade experts and policy makers to explore the answer of lackness for diversification in export, HS-2- digits aggregated data for cotton sub-sectors have been used with latest data from 2004 to 2013 for the panel 39 countries. Revealed comparative advantage (RCA) index and gravity model approach was employed considering country and time specific fixed effect. The RCA index revealed that cotton sub-sectors have comparative advantage in export and there is gradual gain in the competitiveness with time. The opportunity exists in the markets of low, lower-middle and upper middle income countries and countries those have fair trade (low tariff and non-tariff barriers) for cotton export. Greater export potential lies with malaysia, kenya jordan, thailand, mauritius, netherlands norway, Australia and russian federation for export of cotton, however, export potential for cotton has been exhausted with canada, france, india, iran and saudi arabia. The study provide the policy information that countries of Latin america, eastern europe, central asia and northern africa are virgin for export. Therefore, pakistan should penetrate in these markets for export of cotton and other agricultural products. cognizant to new trade theories, pakistan focus on quality to gain maximum trade volume in the markets of high income countries, Pakistan may develop trade agreement with ASEAN, SAFTA, and EU-27 for export of agricultural products. (author)

  15. Values in the trash

    DEFF Research Database (Denmark)

    Gjerris, Mickey; Gaiani, S.

    2015-01-01

    and is one of the important contributors to climate change, simply seems wrong. Here we discuss three questions in relation of this almost self-evident fact: (1) different definitions of food waste and the difficulties in reaching a global definition, how desirable it might be; (2) different ways......Food waste is one of the most discussed subjects within food production in recent years. Throwing food away at a time when almost 900 million humans live in hunger and it is becoming more and more clear that food production draws on limited resources of eg. agricultural land and fresh water...... of preventing food waste from the individual to the international level and the importance of examining the values behind different strategies; and (3) ethical challenges in relation to food waste and the opportunity to utilize the indignation that many feel when confronted with food waste to re...

  16. Trashing the planet

    International Nuclear Information System (INIS)

    Ray, D.L.; Guzzo, L.

    1990-01-01

    The authors use a common sense approach to their goals of clarifying environmental issues, separating fact from factoid, unmaking the dooms-crying opponents of all progress, and re-establishing a sense of reason and balance with respect to the environment, modern technology and science. The introductory section is a discussion of man, technology, and the environment. The authors point out the three major problem areas in the interface between science, the media, and the public: anxiety, factoids, and misinterpretation. They also discuss the reality of the economic and technological changes from the good old days. The second section of the book focuses on four major environmental issues: the greenhouse effect; acid rain; pesticides; and chemical toxins (asbestos, PCB, dioxin). In the third section the authors present a broad approach to the nuclear issues facing us: understanding of radiation; nuclear medicine; nuclear power; and nuclear waste. Finally the book concludes with a section of environmentalism and the future. The authors discuss political environmental activism, governmental actions, and global prospective. They also list four common sense approaches for ordinary citizens: pressure on the legislative branch of government; refusal to listen to the just in case argument; keeping a sense of perspective; and realizing that humans have the responsibility to be good stewards while at the same time they cannot live without altering the earth. At the end of the book there is a sizable section of endnotes and referenced citations

  17. From trash to art

    OpenAIRE

    Požar, Matjaž

    2015-01-01

    The time in which we live is marked by environmental problems and massive amounts of waste, which is increasing day by day. Plastics packaging, plastic cutlery, cans ... objects that serve only for single use. Some of this waste is recycled, but still not enough. In recent years, awareness of the problem of waste is increasing, because in some countries, people are literally drowning in them. A major problem are those, who ignore warnings and instructions regarding the disposal and recycling ...

  18. Microbial contamination of water-soaked cotton gauze and its cause.

    Science.gov (United States)

    Oie, S; Yoshida, H; Kamiya, A

    2001-01-01

    Seven in-use cotton gauze samples and three cotton balls soaked in sterile distilled water in canisters were investigated 7 days after they were prepared in hospital. All samples were contaminated with bacteria including 10(6) to 10(7) colony forming units/ml of Pseudomonas aeruginosa. In vitro viability tests using cotton gauze and cotton balls soaked in sterile distilled water revealed rapid proliferation of P. aeruginosa, Serratia marcescens and Candida albicans. Since the cotton gauze and the cotton balls were soaked in water containing nutrients, such as protein and glucose, these materials may be readily contaminated with bacteria including P. aeruginosa. Thus, when using cotton gauze and cotton balls containing water, microbial contamination should be expected.

  19. Incorporating a Sorghum Habitat for Enhancing Lady Beetles (Coleoptera: Coccinellidae in Cotton

    Directory of Open Access Journals (Sweden)

    P. G. Tillman

    2012-01-01

    Full Text Available Lady beetles (Coleoptera: Coccinellidae prey on insect pests in cotton. The objective of this 2 yr on-farm study was to document the impact of a grain sorghum trap crop on the density of Coccinellidae on nearby cotton. Scymnus spp., Coccinella septempunctata (L., Hippodamia convergens Guérin-Méneville, Harmonia axyridis (Pallas, Coleomegilla maculata (De Geer, Cycloneda munda (Say, and Olla v-nigrum (Mulsant were found in sorghum over both years. Lady beetle compositions in sorghum and cotton and in yellow pyramidal traps were similar. For both years, density of lady beetles generally was higher on cotton with sorghum than on control cotton. Our results indicate that sorghum was a source of lady beetles in cotton, and thus incorporation of a sorghum habitat in farmscapes with cotton has great potential to enhance biocontrol of insect pests in cotton.

  20. Responses of reniform nematode and browntop millet to tillage, cover crop, and herbicides in cotton

    Science.gov (United States)

    Cropping practices that reduce competition from reniform nematode (Rotylenchulus reniformis) and browntop millet (Urochlora ramosum) may help minimize losses in cotton (Gossypium hirsutum). The impacts of tillage, rye cover crop, and preemergence and postemergence herbicides on cotton yields, renifo...

  1. Efficacy of Cotton Root Destruction and Winter Cover Crops for Suppression of Hoplolaimus columbus.

    Science.gov (United States)

    Davis, R F; Baird, R E; McNeil, R D

    2000-12-01

    The efficacy of rye (Secale cereale) and wheat (Triticum aestivum) winter cover crops and cotton stalk and root destruction (i.e., pulling them up) were evaluated in field tests during two growing seasons for Hoplolaimus columbus management in cotton. The effect of removing debris from the field following root destruction also was evaluated. Wheat and rye produced similar amounts of biomass, and both crops produced more biomass (P Cover crops did not suppress H. columbus population levels or increase subsequent cotton yields. Cotton root destruction did not affect cotton stand or plant height the following year. Cotton root destruction lowered (P rye or wheat cover crop or cotton root destruction following harvest is ineffective for H. columbus management in cotton.

  2. Cotton nanofibers obtained by different acid conditions

    International Nuclear Information System (INIS)

    Teixeira, Eliangela de M.; Oliveira, Caue Ribeiro de; Mattoso, Luiz H.C.; Correa, Ana Carolina; Palladin, Priscila

    2009-01-01

    The thermal stability of cellulose nanofibers is related to their application and especially to polymer processing which temperatures of processing are around 200 deg C. In this work, nanofibers of commercial cotton were obtained by acid hydrolysis employing different acids: sulfuric, hydrochloric and a mixture (2:1; sulfuric acid: hydrochloric acid).The morphology of the nanofibers were characterized by transmission microscopy (TEM), crystallinity by x-ray diffraction (XRD) and thermal stability in air atmosphere by thermogravimetric analysis (TGA). The results indicated a very similar morphology and crystallinity among them. The main differences were relative to aggregation state e and thermal stability. The aggregation state of the suspensions decreases in the order HCl 2 SO 4 :HCl 2 SO 4- . The hydrolysis with a mix of HCl and H 2 SO 4 resulted in cellulose nanofibers with higher thermal stability than those hydrolyzed with H 2 SO 4 . The hydrolysis employed with a mixture of sulphuric and hydrochloric acids also showed a better dispersion than those suspensions of nanofibers obtained by hydrolysis with only HCl. (author)

  3. Polyploidization altered gene functions in cotton (Gossypium spp.).

    Science.gov (United States)

    Xu, Zhanyou; Yu, John Z; Cho, Jaemin; Yu, Jing; Kohel, Russell J; Percy, Richard G

    2010-12-16

    Cotton (Gossypium spp.) is an important crop plant that is widely grown to produce both natural textile fibers and cottonseed oil. Cotton fibers, the economically more important product of the cotton plant, are seed trichomes derived from individual cells of the epidermal layer of the seed coat. It has been known for a long time that large numbers of genes determine the development of cotton fiber, and more recently it has been determined that these genes are distributed across At and Dt subgenomes of tetraploid AD cottons. In the present study, the organization and evolution of the fiber development genes were investigated through the construction of an integrated genetic and physical map of fiber development genes whose functions have been verified and confirmed. A total of 535 cotton fiber development genes, including 103 fiber transcription factors, 259 fiber development genes, and 173 SSR-contained fiber ESTs, were analyzed at the subgenome level. A total of 499 fiber related contigs were selected and assembled. Together these contigs covered about 151 Mb in physical length, or about 6.7% of the tetraploid cotton genome. Among the 499 contigs, 397 were anchored onto individual chromosomes. Results from our studies on the distribution patterns of the fiber development genes and transcription factors between the At and Dt subgenomes showed that more transcription factors were from Dt subgenome than At, whereas more fiber development genes were from At subgenome than Dt. Combining our mapping results with previous reports that more fiber QTLs were mapped in Dt subgenome than At subgenome, the results suggested a new functional hypothesis for tetraploid cotton. After the merging of the two diploid Gossypium genomes, the At subgenome has provided most of the genes for fiber development, because it continues to function similar to its fiber producing diploid A genome ancestor. On the other hand, the Dt subgenome, with its non-fiber producing D genome ancestor

  4. Dynamic and Stochastic Structures of U.S. Cotton Exports and Mill Demand

    OpenAIRE

    Fadiga, Mohamadou L.

    2006-01-01

    This study employs a structural time-series method to model and estimate U.S. cotton exports and mill use. The results show that the stochastic process governing cotton export fluctuations is transitory, while the process pertaining to mill use has transitory, seasonal, and secular origins. The estimated structural relationships after accounting for the unobserved components indicate U.S. cotton exports respond directly to higher international price relative to domestic price of cotton, while...

  5. ANALYSIS OF EXCHANGE RATE LINKED SUBSIDIES FOR NON-PRICE EXPORT PROMOTION: THE CASE OF COTTON

    OpenAIRE

    Paudel, Laxmi; Adhikari, Murali; Houston, Jack E.; Kinnucan, Henry W.

    2002-01-01

    An equilibrium displacement framework was developed to evaluate the effect of exchange rate linked subsidies for non-price export promotion for US cotton. Study results show that an increase in promotion expenditure increased the dollar value and producer welfare of cotton growers. The gross gain to the domestic cotton producers from the exchange-rate linked subsidy scheme was positive. These evidences support exchange rate linked subsidies for US cotton export promotion.

  6. Finding the moral fiber: Why reform is urgently needed for a fair cotton trade

    OpenAIRE

    Pfeifer, K.; Kripke, G.; Alpert, E.

    2004-01-01

    Metadata only record US subsidies have led to depressed world cotton prices, which in turn have cost countries in Africa millions of dollars in lost export earnings. Oxfam estimates that sub-Saharan African countries lost $305 million due to US subsidies in crop year 2001. Because cotton is an important livelihood for millions of poor people, Oxfam believes action is urgently needed to reform the distortions in cotton trade that undermine the value of cotton to developing countries. The ce...

  7. Insect pests management of bt cotton through the manipulation of different eco-friendly techniques

    International Nuclear Information System (INIS)

    Ahmad, N.; Khan, M.H.; Tofique, M.

    2011-01-01

    This study was designed to manage insect pests of Bt cotton through the manipulation of different eco-friendly techniques. A perusal of data, based on the overall performance of different treatments reflected that lowest population of jassids (0.29) was observed in bio-control treated Bt cotton followed by bio-control treated conventional cotton (0.41). Mean per leaf population of thrips was found lowest in insecticide treated Bt cotton (0.97) which was statically at par with bi-control treated conventional cotton (0.95), biocontrol treated Bt cotton (1.09) and colour traps treated Bt cotton (1.50). In case of white flies, bio-control treated Bt cotton and bio-control treated conventional cotton again proved effective in maintaining the population at lower levels per leaf (0.33 and 0.35 respectively). No bollworms infestation was recorded in transgenic cotton whereas higher attack of the same was observed in the untreated conventional cotton block. The best results were achieved with the application of bio-control agents in combination with Bt cotton resulting in least infestation by insect pests and maximum seed yield of 3657 kg/ha. The population of Chrysoperla carnea was significantly higher in Bt and conventional cotton treated with bio-control agents as compared to the other treatments. The parasitism percentage of Trichogramma chilonis was observed significantly higher in bio-control treated conventional cotton. The studies manifested that combination of bio-control technology with Bt cotton effectively preserves the local beneficial insect fauna indicating its potential to be used as integrated management system against different insect pests of cotton. (author)

  8. POLICY IMPLICATIONS OF TEXTILE TRADE MANAGEMENT AND THE U.S. COTTON INDUSTRY

    OpenAIRE

    Shui, Shangnan; Wohlgenant, Michael K.; Beghin, John C.

    1993-01-01

    This study investigates the effects on the U.S. cotton industry of textile trade liberalization using a multi-market equilibrium displacement model. The simulation results suggest that textile trade liberalization would induce small changes in the total demand for U.S. cotton but would affect considerable y U.S. cotton demand structure, making U. S, cotton growers more dependent on world markets. The welfare analyses reveal that textile trade liberalization would result in a small welfare los...

  9. Cotton Trade Liberalizations and Domestic Agricultural Policy Reforms: A Partial Equilibrium Analysis

    OpenAIRE

    Pan, Suwen; Fadiga, Mohamadou L.; Mohanty, Samarendu; Welch, Mark

    2006-01-01

    This paper analyzed the effects of trade liberalizing reforms in the world cotton market using a partial equilibrium model. The simulation results indicated that a removal of domestic subsidies and border tariffs for cotton would increase the amount of world cotton trade by an average of 4% in the next five years and world cotton prices by an average of 12% over the same time horizon. The findings indicated that under the liberalization policy, the United States would lose part of its export ...

  10. A Grey Fuzzy Logic Approach for Cotton Fibre Selection

    Science.gov (United States)

    Chakraborty, Shankar; Das, Partha Protim; Kumar, Vidyapati

    2017-06-01

    It is a well known fact that the quality of ring spun yarn predominantly depends on various physical properties of cotton fibre. Any variation in these fibre properties may affect the strength and unevenness of the final yarn. Thus, so as to achieve the desired yarn quality and characteristics, it becomes imperative for the spinning industry personnel to identify the most suitable cotton fibre from a set of feasible alternatives in presence of several conflicting properties/attributes. This cotton fibre selection process can be modelled as a Multi-Criteria Decision Making (MCDM) problem. In this paper, a grey fuzzy logic-based approach is proposed for selection of the most apposite cotton fibre from 17 alternatives evaluated based on six important fibre properties. It is observed that the preference order of the top-ranked cotton fibres derived using the grey fuzzy logic approach closely matches with that attained by the past researchers which proves the application potentiality of this method in solving varying MCDM problems in textile industries.

  11. Effect of low doses gamma irradiation of cotton seeds

    International Nuclear Information System (INIS)

    Al-Oudat, M.; Khalifa, Kh.

    1996-01-01

    Field experiments and then large scale application of irradiated cotton seeds (C.V. Aleppo-40) were carried out during three seasons (1986, 1987 and 1988) for field experiment at ACSAD Station in Dier-Ezzor and 1988, 1989 and 1990 for large scale application at Euphrate's Basin, Al-Ghab and Salamia, farmers farms. The above areas were selected as they represent major cotton production areas in Syria. The aims of the experiments were to study the effect of low doses of gamma irradiation 0, 5, 10, 20, 30, 40 and 50 Gy on cotton yield and to look for the optimum dose of gamma irradiation to obtain best results. The results show that, there were positive effect (P<0.95) for doses 5-30 Gy in increasing cotton yield. The highest increase was at dose of 10 Gy. which as 19.5% higher than control. For the large scale application using 10 Gy the increase in cotton yield varied from 10-39% compared to control. (author). 11 refs., 6 figs

  12. Atmospheric Pressure Plasma Treatment for Grey Cotton Knitted Fabric

    Directory of Open Access Journals (Sweden)

    Chi-wai Kan

    2018-01-01

    Full Text Available 100% grey cotton knitted fabric contains impurities and yellowness and needs to be prepared for processing to make it suitable for coloration and finishing. Therefore, conventionally 100% grey cotton knitted fabric undergoes a process of scouring and bleaching, which involves the use of large amounts of water and chemicals, in order to remove impurities and yellowness. Due to increased environmental awareness, pursuing a reduction of water and chemicals is a current trend in textile processing. In this study, we explore the possibility of using atmospheric pressure plasma as a dry process to treat 100% grey cotton knitted fabric (single jersey and interlock before processing. Experimental results reveal that atmospheric pressure plasma treatment can effectively remove impurities from 100% grey cotton knitted fabrics and significantly improve its water absorption property. On the other hand, if 100% grey cotton knitted fabrics are pretreated with plasma and then undergo a normal scouring process, the treatment time is reduced. In addition, the surface morphological and chemical changes in plasma-treated fabrics were studied and compared with the conventionally treated fabrics using scanning electron microscope (SEM, Fourier-transform infrared spectroscopy-attenuated total reflection (FTIR-ATR and X-ray photoelectron spectroscopy (XPS. The decrease in carbon content, as shown in XPS, reveal the removal of surface impurities. The oxygen-to-carbon (O/C ratios of the plasma treated knitted fabrics reveal enhanced hydrophilicity.

  13. Remediation of deltamethrin contaminated cotton fields: residual and adsorption assessment

    Directory of Open Access Journals (Sweden)

    Rafique Uzaira

    2016-01-01

    Full Text Available Pakistan occupies a significant global position in the growing of high quality cotton. The extensive application of pesticides on agricultural products leads to environmental risk due to toxic residues in air, water and soil. This study examined the chemodynamic effect of Deltamethrin on cotton fields. Samples were collected from the cotton fields of D.G. Khan, Pakistan and analyzed for heavy metal speciation patterns. Batch experiments were administered in order to study the adsorption of Deltamethrin in cotton fields. The effect of different factors including pH, adsorbate dose, and adsorbent mass on adsorption were studied. It was observed that in general, adsorption increased with increases in the mass of adsorbate, although the trends were irregular. Residual fractions of deltamethrin in the soil and water of cotton fields were analyzed to assess concentrations of xenobiotics bound to soil particles. Results indicated that such residues are significantly higher in soil samples due to high Koc in comparison to water, indicating the former is an efficient degradation agent. Results from the batch experiment resulted in 95% removal with alkaline pH and an adsorbent-adsorbate ratio of 250:1. These results may be used to environment friendly resource management policies.

  14. Isolation and characterization of gene sequences expressed in cotton fiber

    Directory of Open Access Journals (Sweden)

    Taciana de Carvalho Coutinho

    2016-06-01

    Full Text Available ABSTRACT Cotton fiber are tubular cells which develop from the differentiation of ovule epidermis. In addition to being one of the most important natural fiber of the textile group, cotton fiber afford an excellent experimental system for studying the cell wall. The aim of this work was to isolate and characterise the genes expressed in cotton fiber (Gossypium hirsutum L. to be used in future work in cotton breeding. Fiber of the cotton cultivar CNPA ITA 90 II were used to extract RNA for the subsequent generation of a cDNA library. Seventeen sequences were obtained, of which 14 were already described in the NCBI database (National Centre for Biotechnology Information, such as those encoding the lipid transfer proteins (LTPs and arabinogalactans (AGP. However, other cDNAs such as the B05 clone, which displays homology with the glycosyltransferases, have still not been described for this crop. Nevertheless, results showed that several clones obtained in this study are associated with cell wall proteins, wall-modifying enzymes and lipid transfer proteins directly involved in fiber development.

  15. Systems for harvesting and handling cotton plant residue

    Energy Technology Data Exchange (ETDEWEB)

    Coates, W. [Univ. of Arizona, Tucson, AZ (United States)

    1993-12-31

    In the warmer regions of the United States, cotton plant residue must be buried to prevent it from serving as an overwintering site for insect pests such as the pink bollworm. Most of the field operations used to bury the residue are high energy consumers and tend to degrade soil structure, thereby increasing the potential for erosion. The residue is of little value as a soil amendment and consequently is considered a negative value biomass. A commercial system to harvest cotton plant residue would be of both economic and environmental benefit to cotton producers. Research has been underway at the University of Arizona since the spring of 1991 to develop a commercially viable system for harvesting cotton plant residue. Equipment durability, degree of densification, energy required, cleanliness of the harvested material, and ease of product handling and transport are some of the performance variables which have been measured. Two systems have proven superior. In both, the plants are pulled from the ground using an implement developed specifically for the purpose. In one system, the stalks are baled using a large round baler, while in the other the stalks are chopped with a forage harvester, and then made into packages using a cotton module maker. Field capacities, energy requirements, package density and durability, and ease of handling with commercially available equipment have been measured for both systems. Selection of an optimum system for a specific operation depends upon end use of the product, and upon equipment availability.

  16. Stink Bug Feeding Induces Fluorescence in Developing Cotton Bolls

    Directory of Open Access Journals (Sweden)

    Toews Michael D

    2011-08-01

    Full Text Available Abstract Background Stink bugs (Hemiptera: Pentatomidae comprise a critically important insect pest complex affecting 12 major crops worldwide including cotton. In the US, stink bug damage to developing cotton bolls causes boll abscission, lint staining, reduced fiber quality, and reduced yields with estimated losses ranging from 10 to 60 million dollars annually. Unfortunately, scouting for stink bug damage in the field is laborious and excessively time consuming. To improve scouting accuracy and efficiency, we investigated fluorescence changes in cotton boll tissues as a result of stink bug feeding. Results Fluorescent imaging under long-wave ultraviolet light showed that stink bug-damaged lint, the inner carpal wall, and the outside of the boll emitted strong blue-green fluorescence in a circular region near the puncture wound, whereas undamaged tissue emissions occurred at different wavelengths; the much weaker emission of undamaged tissue was dominated by chlorophyll fluorescence. We further characterized the optimum emission and excitation spectra to distinguish between stink bug damaged bolls from undamaged bolls. Conclusions The observed characteristic fluorescence peaks associated with stink bug damage give rise to a fluorescence-based method to rapidly distinguish between undamaged and stink bug damaged cotton bolls. Based on the fluorescent fingerprint, we envision a fluorescence reflectance imaging or a fluorescence ratiometric device to assist pest management professionals with rapidly determining the extent of stink bug damage in a cotton field.

  17. Diversity, Mutation and Recombination Analysis of Cotton Leaf Curl Geminiviruses.

    Directory of Open Access Journals (Sweden)

    Huma Saleem

    Full Text Available The spread of cotton leaf curl disease in China, India and Pakistan is a recent phenomenon. Analysis of available sequence data determined that there is a substantial diversity of cotton-infecting geminiviruses in Pakistan. Phylogenetic analyses indicated that recombination between two major groups of viruses, cotton leaf curl Multan virus (CLCuMuV and cotton leaf curl Kokhran virus (CLCuKoV, led to the emergence of several new viruses. Recombination detection programs and phylogenetic analyses showed that CLCuMuV and CLCuKoV are highly recombinant viruses. Indeed, CLCuKoV appeared to be a major donor virus for the coat protein (CP gene, while CLCuMuV donated the Rep gene in the majority of recombination events. Using recombination free nucleotide datasets the substitution rates for CP and Rep genes were determined. We inferred similar nucleotide substitution rates for the CLCuMuV-Rep gene (4.96X10-4 and CLCuKoV-CP gene (2.706X10-4, whereas relatively higher substitution rates were observed for CLCuMuV-CP and CLCuKoV-Rep genes. The combination of sequences with equal and relatively low substitution rates, seemed to result in the emergence of viral isolates that caused epidemics in Pakistan and India. Our findings also suggest that CLCuMuV is spreading at an alarming rate, which can potentially be a threat to cotton production in the Indian subcontinent.

  18. Yield components and quality of intercropped cotton in response to mepiquat chloride and plant density

    NARCIS (Netherlands)

    Mao, Lili; Zhang, Lizhen; Evers, J.B.; Werf, van der Wopke; Liu, Shaodong; Zhang, Siping; Wang, Baomin; Li, Zhaohu

    2015-01-01

    Cotton yield is greatly improved by moderately increasing plant density and modifying the cotton plants to have a compact structure, which is also required by the increasing demand for mechanized harvest. However, in cotton strip intercropped with wheat, only limited knowledge on yield response

  19. King Cotton's Lasting Legacy of Poverty and Southern Region Contemporary Conditions

    Science.gov (United States)

    Guthrie, James W.; Peevely, Gary

    2010-01-01

    One hundred fifty years ago, cotton was considered as the king of all United States' agricultural exports. Cotton's dollar value far exceeded that of any other mid-19th-century United States trade item, much more than tobacco, fish, forest products, raw materials for manufacturing, or manufactured items. Indeed, in the mid-19th century, cotton was…

  20. 78 FR 9330 - Revision of Regulations Defining Bona Fide Cotton Spot Markets

    Science.gov (United States)

    2013-02-08

    ... Cotton Spot Markets AGENCY: Agricultural Marketing Service, USDA. ACTION: Proposed rule. SUMMARY: The... bona fide cotton spot markets in order to assure consistency with the revised Cotton Research and Promotion Act. Updated bona fide spot market definitions will allow for published spot quotes to consider...

  1. Effect Of Bird Manure On Cotton Plants Grown On Soils Sampled ...

    African Journals Online (AJOL)

    Cotton plant had a better development and growth when bird manure was only applied to soil or combined with mineral fertilizer and when cotton was grown on a soil where the previous crops were cereals (maize or sorghum). Planting cotton on a soil where the previous crop grown was maize or sorghum had no significant ...

  2. Employment Opportunities and Training Needs in Agribusiness. Competencies for Cotton Production in the United States.

    Science.gov (United States)

    Holcomb, John W.; And Others

    The competencies necessary for entry and advancement in cotton production were determined by surveying people in the cotton production industry from nine of the ten leading cotton producing states. A preliminary listing of competencies was developed from a review of the literature and from a survey of specialized personnel in soil and crop…

  3. Orientation of cotton growers of multan district about heal hazards and pesticide use

    International Nuclear Information System (INIS)

    Haq, Q.U.; Hussain, R.; Ali, T.; Ahmad, M.

    2008-01-01

    Cotton growing farmers and cotton pickers are the twin pillars of cotton growing community. Cotton growing farmers (male) are involved in monitoring of quality and quantity of cotton crops by handsome usage of pesticides for better marketing of cotton crops. Whereas, cotton pickers (female) are involved in picking of cotton mainly. To assess their knowledge and source of knowledge about pesticides related health problems, the study was designed and conducted in 20 villages of district Multan selected by multistage random sampling technique. From the selected 20 villages, from the list bearing the villages, mouzas and union councils of district Multan, 220 cotton growers and 150 cotton pickers were selected by simple random sampling technique and interviewed through a reliable and validated interview schedule. The data collected were processed through Statistical Package for Social Sciences (SPSS). The results showed that 75% of cotton growing farmers were having orientation about side effects of pesticides whereas, almost 8% of cotton growers were having no knowledge about side effects of pesticides. (author)

  4. 7 CFR 1427.16 - Movement and protection of warehouse-stored cotton.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 10 2010-01-01 2010-01-01 false Movement and protection of warehouse-stored cotton. 1427.16 Section 1427.16 Agriculture Regulations of the Department of Agriculture (Continued) COMMODITY... Cotton Loan and Loan Deficiency Payments § 1427.16 Movement and protection of warehouse-stored cotton. (a...

  5. Low-level hydrogen peroxide generation by unbleached cotton nonwovens: implications for wound healing applications

    Science.gov (United States)

    Greige cotton is an intact plant fiber. The cuticle and primary cell wall near the outer surface of the cotton fiber contains pectin, peroxidases, superoxide dismutase (SOD), and trace metals, which are associated with hydrogen peroxide (H2O2) generation during cotton fiber development. The compon...

  6. Association of Verde plant bug, Creontiades signatus (Hemiptera: Miridae), with cotton boll rot

    Science.gov (United States)

    Cotton along the Gulf Coast of south Texas has experienced loss from cotton boll rot especially during the last 10 to 15 years, and stink bugs and plant bugs (Hemiptera: Pentatomidae and Miridae) that feed on cotton bolls have been suspected in introducing the disease. A replicated grower field surv...

  7. 49 CFR 176.903 - Stowage of cotton or vegetable fibers with coal.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Stowage of cotton or vegetable fibers with coal... § 176.903 Stowage of cotton or vegetable fibers with coal. Cotton or vegetable fibers being transported on a vessel may not be stowed in the same hold with coal. They may be stowed in adjacent holds if the...

  8. Response of successive three generations of cotton bollworm, Helicoverpa armigera (Hübner), fed on cotton bolls, under elevated CO2

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The growth, development and consumption of successive three generations of cotton bollworm, Helicoverpa armigera (Hübner), fed on cotton bolls grown under elevated CO2 (double-ambient vs. ambient) in open-top chambers were examined. Significant decreases in protein, total amino acid, water and nitrogen content and increases in free fatty acid were observed in cotton bolls. Changes in quality of cotton bolls affected the growth, development and food utilization of H. armigera. Significantly longer larval development duration in three successive generations and lower pupal weight of the second and third generations were observed in cotton bollworm fed on cotton bolls grown under elevated CO2. Significantly lower fecundity was also found in successive three generations of H. armigera fed on cotton bolls grown under elevated CO2. The consumption per larva occurred significant increase in successive three generations and frass per larva were also significantly increased during the second and third generations under elevated CO2. Significantly lower relative growth rate, efficiency of conversion of ingested food and significant higher relative consumption rate in successive three generations were observed in cotton bollworm fed on cotton bolls grown under elevated CO2. Significantly lower potential female fecundity, larval numbers and population consumption were found in the second and third generations of cotton bollworm fed on cotton bolls grown under elevated CO2. The integrative effect of higher larval mortality rate and lower adult fecundity resulted in significant decreases in potential population consumption in the latter two generations. The results show that elevated CO2 adversely affects cotton bolls quality, which indicates the potential population dynamics and potential population consumption of cotton bollworm will alleviate the harm to the plants in the future rising CO2 atmosphere.

  9. Semiochemicals from herbivory induced cotton plants enhance the foraging behavior of the cotton boll weevil, Anthonomus grandis.

    Science.gov (United States)

    Magalhães, D M; Borges, M; Laumann, R A; Sujii, E R; Mayon, P; Caulfield, J C; Midega, C A O; Khan, Z R; Pickett, J A; Birkett, M A; Blassioli-Moraes, M C

    2012-12-01

    The boll weevil, Anthonomus grandis, has been monitored through deployment of traps baited with aggregation pheromone components. However, field studies have shown that the number of insects caught in these traps is significantly reduced during cotton squaring, suggesting that volatiles produced by plants at this phenological stage may be involved in attraction. Here, we evaluated the chemical profile of volatile organic compounds (VOCs) emitted by undamaged or damaged cotton plants at different phenological stages, under different infestation conditions, and determined the attractiveness of these VOCs to adults of A. grandis. In addition, we investigated whether or not VOCs released by cotton plants enhanced the attractiveness of the aggregation pheromone emitted by male boll weevils. Behavioral responses of A. grandis to VOCs from conspecific-damaged, heterospecific-damaged (Spodoptera frugiperda and Euschistus heros) and undamaged cotton plants, at different phenological stages, were assessed in Y-tube olfactometers. The results showed that volatiles emitted from reproductive cotton plants damaged by conspecifics were attractive to adults boll weevils, whereas volatiles induced by heterospecific herbivores were not as attractive. Additionally, addition of boll weevil-induced volatiles from reproductive cotton plants to aggregation pheromone gave increased attraction, relative to the pheromone alone. The VOC profiles of undamaged and mechanically damaged cotton plants, in both phenological stages, were not different. Chemical analysis showed that cotton plants produced qualitatively similar volatile profiles regardless of damage type, but the quantities produced differed according to the plant's phenological stage and the herbivore species. Notably, vegetative cotton plants released higher amounts of VOCs compared to reproductive plants. At both stages, the highest rate of VOC release was observed in A. grandis-damaged plants. Results show that A. grandis uses

  10. The cotton mealybug, Phenacoccus solenopsis Tinsley (Hemiptera: Pseudococcidae as a new menace to cotton in Egypt and its chemical control

    Directory of Open Access Journals (Sweden)

    El-Zahi El-Zahi Saber

    2016-04-01

    Full Text Available The cotton mealybug, Phenacoccus solenopsis Tinsley (Hemiptera: Pseudococcidae is a polyphagous sap sucking insect with a wide geographical and host range causing severe losses in economically important crops. This study represents the first record of P. solenopsis as a new insect attacking cotton plants (Gossypium barbadense var. Giza 86 in Kafr El-Sheikh governorate, Egypt. The insect was noticed on cotton plants for the first time during its growing season of 2014. The mealybug specimens were collected from infested cotton plants and identified as P. solenopsis. In an attempt to control this pest, eight toxic materials viz., imidacloprid, thiamethoxam, flonicamid, emamectin-benzoate, chlorpyrifos, methomyl, deltamethrin and mineral oil (KZ-oil, belonging to different chemical groups, were tested for their influence against P. solenopsis on cotton under field conditions. Methomyl, imidacloprid, thiamethoxam and chlorpyrifos showed the highest efficacy against P. solenopsis recording 92.3 to 80.4% reduction of the insect population. Flonicamid, emamectin-benzoate and KZ-oil failed to exhibit sufficient P. solenopsis control.

  11. Transgenic Cotton Plants Expressing the HaHR3 Gene Conferred Enhanced Resistance to Helicoverpa armigera and Improved Cotton Yield.

    Science.gov (United States)

    Han, Qiang; Wang, Zhenzhen; He, Yunxin; Xiong, Yehui; Lv, Shun; Li, Shupeng; Zhang, Zhigang; Qiu, Dewen; Zeng, Hongmei

    2017-08-30

    RNA interference (RNAi) has been developed as an efficient technology. RNAi insect-resistant transgenic plants expressing double-stranded RNA (dsRNA) that is ingested into insects to silence target genes can affect the viability of these pests or even lead to their death. HaHR3 , a molt-regulating transcription factor gene, was previously selected as a target expressed in bacteria and tobacco plants to control Helicoverpa armigera by RNAi technology. In this work, we selected the dsRNA- HaHR3 fragment to silence HaHR3 in cotton bollworm for plant mediated-RNAi research. A total of 19 transgenic cotton lines expressing HaHR3 were successfully cultivated, and seven generated lines were used to perform feeding bioassays. Transgenic cotton plants expressing ds HaHR3 were shown to induce high larval mortality and deformities of pupation and adult eclosion when used to feed the newly hatched larvae, and 3rd and 5th instar larvae of H. armigera . Moreover, HaHR3 transgenic cotton also demonstrated an improved cotton yield when compared with controls.

  12. Effects of the irradiation in seeds of cotton

    International Nuclear Information System (INIS)

    Araujo, Ana Leticia; Arthur, Paula Bergamin; Arthur, Valter; Franco, Camilo Flamorion de Oliveira

    2017-01-01

    The experiment aimed to verify if seeds of cotton of variety FiberMax FM 993, irradiated with the doses of 0 (test); 25; 50; 75; 100 Gy can induce the production increase in cotton culture. For all treatments with irradiation, was used a source of cobalt-60, type Gammacell 220. After the irradiation, the seeds were planted in the experimental field of the Department of Plant Production ESALQ-USP, Piracicaba-SP. The experimental design was randomized blocks with four replications and 60 g of seed were used for each repetition, the rows were 5m and the spacing of 0.90m, using randomized blocks and rows of edging. After planting the final height and productivity were evaluated. The obtained data were statistically analyzed in the Tukey test at 5% level of probability. From the results obtained, it was concluded that the dose of 50Gy was the one that induced a greater production of cotton. (author)

  13. Conductive Cotton Textile from Safely Functionalized Carbon Nanotubes

    Directory of Open Access Journals (Sweden)

    Mohammad Jellur Rahman

    2015-01-01

    Full Text Available Electroconductive cotton textile has been prepared by a simple dipping-drying coating technique using safely functionalized multiwalled carbon nanotubes (f-MWCNTs. Owing to the surface functional groups, the f-MWCNTs become strongly attached with the cotton fibers forming network armors on their surfaces. As a result, the textile exhibits enhanced electrical properties with improved thermal conductivity and therefore is demonstrated as a flexible electrothermal heating element. The fabricated f-MWCNTs/cotton textile can be heated uniformly from room temperature to ca. 100°C within few minutes depending on the applied voltage. The textile shows good thermal stability and repeatability during a long-term heating test.

  14. Chitosan pretreatment for cotton dyeing with black tea

    Science.gov (United States)

    Campos, J.; Díaz-García, P.; Montava, I.; Bonet-Aracil, M.; Bou-Belda, E.

    2017-10-01

    Chitosan is used in a wide range of applications due to its intrinsic properties. Chitosan is a biopolymer obtained from chitin and among their most important aspects highlights its bonding with cotton and its antibacterial properties. In this study two different molecular weight chitosan are used in the dyeing process of cotton with black tea to evaluate its influence. In order to evaluate the effect of the pretreatment with chitosan, DSC and reflection spectrophotometer analysis are performed. The curing temperature is evaluated by the DSC analysis of cotton fabric treated with 15 g/L of chitosan, whilst the enhancement of the dyeing is evaluated by the colorimetric coordinates and the K/S value obtained spectrophotometrically. This study shows the extent of improvement of the pretreatment with chitosan in dyeing with natural products as black tea.

  15. Regressional Estimation of Cotton Sirospun Yarn Properties from Fibre Properties

    Directory of Open Access Journals (Sweden)

    Bedez Üte Tuba

    2014-09-01

    Full Text Available In this paper, it is aimed at determining the equations and models for estimating the sirospun yarn quality characteristics from the yarn production parameters and cotton fibre properties, which are focused on fibre bundle measurements represented by HVI (high volume instrument. For this purpose, a total of 270 sirospun yarn samples were produced on the same ring spinning machine under the same conditions at Ege University, by using 11 different cotton blends and three different strand spacing settings, in four different yarn counts and in three different twist coefficients. The sirospun yarn and cotton fibre property interactions were investigated by correlation analysis. For the prediction of yarn quality characteristics, multivariate linear regression methods were performed. As a result of the study, equations were generated for the prediction of yarn tenacity, breaking elongation, unevenness and hairiness by using fibre and yarn properties. After the goodness of fit statistics, very large determination coefficients (R2 and adjusted R2 were observed.

  16. Effects of the irradiation in seeds of cotton

    Energy Technology Data Exchange (ETDEWEB)

    Araujo, Ana Leticia [Centro de Energia Nuclear na Agricultura (CENA/USP), Piracicaba, SP (Brazil); Arthur, Paula Bergamin; Arthur, Valter, E-mail: paula.arthur@hotmail.com [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil); Franco, Camilo Flamorion de Oliveira [Empresa Brasileira de Pesquisa Agropecuária (EMBRAPA/EMEPA), João Pessoa, PB (Brazil)

    2017-07-01

    The experiment aimed to verify if seeds of cotton of variety FiberMax FM 993, irradiated with the doses of 0 (test); 25; 50; 75; 100 Gy can induce the production increase in cotton culture. For all treatments with irradiation, was used a source of cobalt-60, type Gammacell 220. After the irradiation, the seeds were planted in the experimental field of the Department of Plant Production ESALQ-USP, Piracicaba-SP. The experimental design was randomized blocks with four replications and 60 g of seed were used for each repetition, the rows were 5m and the spacing of 0.90m, using randomized blocks and rows of edging. After planting the final height and productivity were evaluated. The obtained data were statistically analyzed in the Tukey test at 5% level of probability. From the results obtained, it was concluded that the dose of 50Gy was the one that induced a greater production of cotton. (author)

  17. Fabrication of superhydrophobic cotton fabrics by silica hydrosol and hydrophobization

    Science.gov (United States)

    Xu, Lihui; Zhuang, Wei; Xu, Bi; Cai, Zaisheng

    2011-04-01

    Superhydrophobic cotton fabrics were prepared by the incorporation of silica nanoparticles and subsequent hydrophobization with hexadecyltrimethoxysilane (HDTMS). The silica nanoparticles were synthesized via sol-gel reaction with methyl trimethoxy silane (MTMS) as the precursor in the presence of the base catalyst and surfactant in aqueous solution. As for the resulting products, characterization by particle size analyzer, scanning electron microscopy (SEM), scanning probe microscopy (SPM), X-ray photoelectron spectroscopy (XPS), and thermal gravimetric analysis (TGA) were performed respectively. The size of SiO2 nanoparticles can be controlled by adjusting the catalyst and surfactant concentrations. The wettability of cotton textiles was evaluated by the water contact angle (WCA) and water shedding angle (WSA) measurements. The results showed that the treated cotton sample displayed remarkable water repellency with a WCA of 151.9° for a 5 μL water droplet and a WSA of 13° for a 15 μL water droplet.

  18. Características sócio-culturais de práticas ginásticas e futebolísticas no sul do brasil ao final do século XX

    OpenAIRE

    BRUNO, Giancarlo Bazarele Machado; Universidade Federal de Pelotas

    2013-01-01

    Com entrevistas, observações, quantificações e metragens, estudou-se as academias de Ginástica e os locais de Futsal e de Soccer em Pelotas/RS. Um total de 1.570 praticantes, 44,8 alunos/academia, 97 % mulheres, praticavam principalmente Ginástica Localizada, Aeróbica e Step, em 35 locais, área média de 205,4 m2. Pertenciam à iniciativa privada 91,4%, e as restantes a clubes sociais. A maior freqüência era no período antes do verão e entrel7:00 e 22:00 horas. O custo médio, para exercitação d...

  19. Ninguém é de ferro: a construção da corporeidade em uma academia de ginástica feminina de um bairro popular em João Pessoa

    OpenAIRE

    Lira, Manuella Ribeiro Barbosa

    2014-01-01

    A pesquisa que se segue tem como eixo central a construção do corpo feminino na atual sociedade, a partir do desenvolvimento de uma experiência etnográfica em uma academia de ginástica só para mulheres, localizada em um bairro popular da cidade de João Pessoa, no período entre os meses de dezembro de 2012 a dezembro de 2013. Os objetivos do estudo são investigar de que maneira o corpo é construído nas práticas e nos discursos da academia de ginástica só para mulheres, quais os ...

  20. Avaliação do equilíbrio estático e dinâmico de idosas praticantes de hidroginástica e ginástica

    OpenAIRE

    Almeida, Ana Paula Pessoa Veloso de; Veras, Renato Peixoto; Doimo, Leonice Aparecida

    2010-01-01

    Este estudo avaliou o equilíbrio estático e dinâmico e valências motoras relacionadas em idosas praticantes de ginástica e hidroginástica. Participaram 31 mulheres na modalidade hidroginástica (GH, 69,32 ± 6,57 anos) e 28 na ginástica (GG; 65,57 ± 7,67 anos), com no mínimo seis meses de prática e frequência mínina de três vezes na semana. Foram realizadas medidas de estatura (cm), peso (kg) e circunferências de cintura, quadril e abdome (cm) e cálculos do índice de massa corporal (IMC) e rela...

  1. TEST OF COTTON LINES WITH DROUGHT TOLERANT INTERCROPPED WITH MAIZE

    Directory of Open Access Journals (Sweden)

    Kadarwati F.T.

    2017-12-01

    Full Text Available The distribution of cotton cultivation is mostly located in the sub-optimal land due to competition with the field crop. The cotton cultivation in Indonesia is always done through intercropping with pulses. This research aims to test the suitability of cotton lines with drought-tolerant intercropped with maize. The research is conducted in February to August 2016 at Asembagus Experimental Garden, Situbondo. Planting materials used in this research are 6 lines and 2 varieties of drought-tolerant cotton consist of strain 03001/9, 03008/24, 03008/25, 03017/13, 06062/3, 06063/3, kanesia 10 and kanesia 14. The research prepared by the draft randomized group with three replications. The observation parameter consists of plant height, canopy width, number of generative branches, number of fruits, fruits weight, the yield of seed cotton, and corn dry results. The research result shows that the strain 03017/13 and 03008/24 have the highest consecutive acceptance of IDR 17,860,681 and IDR 17,520,879, the increase in revenue compared to monoculture is IDR 6,278,473 and IDR 5,668,191, seed cotton production amounted to 2470.01 kg/ha and 2329.72 kg/ha, maize production amounted to 2001.54 kg/ha and 2112.74 kg/ha, LER 1.68 and 1.60, number of harvested fruit of 12.66 and 11.76 fruits/plant, fruit weight of 4.05 and 4.17 g/fruit.

  2. Isolation and characterization of terpene synthases in cotton (Gossypium hirsutum).

    Science.gov (United States)

    Yang, Chang-Qing; Wu, Xiu-Ming; Ruan, Ju-Xin; Hu, Wen-Li; Mao, Yin-Bo; Chen, Xiao-Ya; Wang, Ling-Jian

    2013-12-01

    Cotton plants accumulate gossypol and related sesquiterpene aldehydes, which function as phytoalexins against pathogens and feeding deterrents to herbivorous insects. However, to date little is known about the biosynthesis of volatile terpenes in this crop. Herein is reported that 5 monoterpenes and 11 sesquiterpenes from extracts of a glanded cotton cultivar, Gossypium hirsutum cv. CCRI12, were detected by gas chromatography-mass spectrometry (GC-MS). By EST data mining combined with Rapid Amplification of cDNA Ends (RACE), full-length cDNAs of three terpene synthases (TPSs), GhTPS1, GhTPS2 and GhTPS3 were isolated. By in vitro assays of the recombinant proteins, it was found that GhTPS1 and GhTPS2 are sesquiterpene synthases: the former converted farnesyl pyrophosphate (FPP) into β-caryophyllene and α-humulene in a ratio of 2:1, whereas the latter produced several sesquiterpenes with guaia-1(10),11-diene as the major product. By contrast, GhTPS3 is a monoterpene synthase, which produced α-pinene, β-pinene, β-phellandrene and trace amounts of other monoterpenes from geranyl pyrophosphate (GPP). The TPS activities were also supported by Virus Induced Gene Silencing (VIGS) in the cotton plant. GhTPS1 and GhTPS3 were highly expressed in the cotton plant overall, whereas GhTPS2 was expressed only in leaves. When stimulated by mechanical wounding, Verticillium dahliae (Vde) elicitor or methyl jasmonate (MeJA), production of terpenes and expression of the corresponding synthase genes were induced. These data demonstrate that the three genes account for the biosynthesis of volatile terpenes of cotton, at least of this Upland cotton. Copyright © 2013 Elsevier Ltd. All rights reserved.

  3. Cotton phenotyping with lidar from a track-mounted platform

    Science.gov (United States)

    French, Andrew N.; Gore, Michael A.; Thompson, Alison

    2016-05-01

    High-Throughput Phenotyping (HTP) is a discipline for rapidly identifying plant architectural and physiological responses to environmental factors such as heat and water stress. Experiments conducted since 2010 at Maricopa, Arizona with a three-fold sensor group, including thermal infrared radiometers, active visible/near infrared reflectance sensors, and acoustic plant height sensors, have shown the validity of HTP with a tractor-based system. However, results from these experiments also show that accuracy of plant phenotyping is limited by the system's inability to discriminate plant components and their local environmental conditions. This limitation may be overcome with plant imaging and laser scanning which can help map details in plant architecture and sunlit/shaded leaves. To test the capability for mapping cotton plants with a laser system, a track-mounted platform was deployed in 2015 over a full canopy and defoliated cotton crop consisting of a scanning LIDAR driven by Arduinocontrolled stepper motors. Using custom Python and Tkinter code, the platform moved autonomously along a pipe-track at 0.1 m/s while collecting LIDAR scans at 25 Hz (0.1667 deg. beam). These tests showed that an autonomous LIDAR platform can reduce HTP logistical problems and provide the capability to accurately map cotton plants and cotton bolls. A prototype track-mounted platform was developed to test the use of LIDAR scanning for High- Throughput Phenotyping (HTP). The platform was deployed in 2015 at Maricopa, Arizona over a senescent cotton crop. Using custom Python and Tkinter code, the platform moved autonomously along a pipe-track at cotton bolls.

  4. POTASSIUM FERTILIZATION AND SOIL MANAGEMENT SYSTEMS FOR COTTON CROPS

    Directory of Open Access Journals (Sweden)

    VITOR MARQUES VIDAL

    2017-01-01

    Full Text Available Cotton has great socio-economic importance due to its use in textile industry, edible oil and biodiesel production and animal feed. Thus, the objective of this work was to identify the best potassium rate and soil management for cotton crops and select among cultivars, the one that better develops in the climatic conditions of the Cerrado biome in the State of Goiás, Brazil. Thus, the effect of five potassium rates (100, 150, 200, 250 and 300 kg ha-1 of K2O and two soil management systems (no-till and conventional tillage on the growth, development and reproduction of four cotton cultivars (BRS-371, BRS-372, BRS-286 and BRS-201 was evaluated. The data on cotton growth and development were subjected to analysis of variance; the data on potassium rates were subjected to regression analysis; and the data on cultivars and soil management to mean test. The correlation between the vegetative and reproductive variables was also assessed. The conventional tillage system provides the best results for the herbaceous cotton, regardless of the others factors evaluated. The cultivar BRS-286 has the best results in the conditions evaluated. The cultivar BRS-371 under no-till system present the highest number of fruiting branches at a potassium rate of 105.5% and highest number of floral buds at a potassium rate of 96.16%. The specific leaf area was positively correlated with the number of bolls per plant at 120 days after emergence of the herbaceous cotton.

  5. “É bom porque é ruim!” Considerações sobre produção e consumo de cultura trash no Brasil

    Directory of Open Access Journals (Sweden)

    Mayka Castellano

    2010-12-01

    Full Text Available Neste artigo, apresento um panorama do circuito de produção e consumo de cultura trash. Amparada em entrevistas em profundidade com fãs/produtores e na realização de uma etnografia virtual em sites de relacionamento, analiso a importância da mídia digital como base para a criação de uma articulada comunidade que cultua artefatos culturais considerados “ruins”. Oriundos tanto da cultura massiva quanto da produção amadora, tais produtos contam com uma dedicada fruição por parte de jovens que usam a diversão como principal justificativa para o engendramento dessa crescente rede de trocas culturais.

  6. Cotton/Wool Printing with Natural Dyes Nano-Particles

    OpenAIRE

    , D Maamoun; , H Osman; , SH Nassar

    2016-01-01

    In the present work, cotton/wool 50/50 blended fabric is printed via three natural dyes nanoparticles namely: turmeric, madder and rhubarb. Dye powder of the three plants was milled for 30 days after which it was exposed to ultrasound for 6 hours. Cotton/wool substrate is mordanted prior to printing process using two mordants separately: tartaric acid and potassium aluminium sulphate (alum). All parameters that are found to inşuence colour intensity as well as fastness levels of the prints ar...

  7. Mechanical damage in cotton buds caused by the boll weevil

    Directory of Open Access Journals (Sweden)

    Santos Roseane Cavalcanti

    2003-01-01

    Full Text Available The boll weevil (Anthonomus grandis Boheman causes high levels of bud abscission in cotton plants due to feeding or oviposition punctures. It has been reported that abscission is mainly due to enzymes present in the insect's saliva, but mechanical damage could also contribute to square abscission. The objective of this paper was to undertake an analysis of the morphological damages caused by the insect in cotton squares using microscopy. Anthers and ovules are the main target of boll weevil feeding. The process initiates by perforation of young sepal and petal tissues and proceeds with subsequent alimentation on stamen and ovary leading to abscission of floral structures.

  8. Physiological response of wheat, maize and cotton to gamma irradiation

    International Nuclear Information System (INIS)

    Sharabash, M.T.M.; Gaweesh, S.S.M.; Orabi, I.O.A.; Hammad, A.H.A.

    1988-01-01

    Grains of wheat triticum aestivum vulgare cv. Giza 155, maize Zea mays cv. double hybrid strain 17 S and cotton seeds Gossypium barbadence cv. Giza 67 were irradiated with successive doses of gamma rays from 0 to 64 Krad. Irradiating wheat grains with 1 Krad, maize grains with 0.5 Krad and cotton seeds with 4 Krad stimulated their germination and enhanced the growth of seedlings and their chlorophyll content. Also, these doses activated Alpha- and Beta-Amylase in the seeds. Higher doses had suppression effects. Peroxidase value in the seedlings of the three species was accelerated progressively in concomitant with the increase in the dosage

  9. Radiation mutagenesis in development of genetic fundamentals of cotton selection

    International Nuclear Information System (INIS)

    Musaev, D.A.; Almatov, A.S.

    1987-01-01

    Some results of investigations on preparation and genetic analysis of mutants in inbreeding lines of genetic collections of cotton plants, as well as problems on mutant application in practical selection are covered. The results show that the scientific authenticity and efficiency of fundamental and applied investigations in the field of experimental mutagenesis of cotton plants,being a facultative self-polinator, depend on keeping necessary methodical requirements. Application of inbreeding lines of genetic collection with marker features as the initial material, isolation of plants usinng self-polination of flowers on all stages of investigation are related to these requirements. Several methodical recommendations on genetic-selective investigations are developed

  10. Ginástica geral na escola: uma proposta metodológica General gymnastics at school: A methodological propositon Gimnasia general en la escuela: Una propuesta metodológica

    Directory of Open Access Journals (Sweden)

    2006-11-01

    Full Text Available Este trabalho tem por objetivo discutir a Ginástica como conteúdo da Educação Física escolar, por meio da Ginástica geral como proposta metodológica. Tal proposta tem como perspectiva a integração das diversas manifestações gímnicas e os outros componentes da cultura corporal, sendo sua principal característica a ausência da competição. PALAVRAS-CHAVE: ginástica – ginástica geral – educação física escolar. This study aims at discussing gym classes as a part of school physical education, using General Gymnastics as a methodological approach. Such an approach has the perspective of integrating the several gymnastic manifestations to the other components of body culture, with the lack of competition as its main feature. KEY WORDS: gym – general gymnastics – physical education in schools. Este trabajo tiene por objetivo discutir la Gimnasia como contenido de la Educación Física escolar, por medio de la Gimnasia general como propuesta metodológica. Tal propuesta tiene como perspectiva la integración de diversas manifestaciones gímnicas y los otros componentes de la cultura corporal, siendo su principal característica la ausencia de la competencia. PALABRAS-CLAVE: gimnasia – gimnasia general – educación física escolar.

  11. Comparative Analysis of Discovery Function of Cotton Future Price among Different Regions——A Case Study of Xinjiang

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Through comparative analysis, We research the relationship between cotton future price and cotton spot price in different regions, in order to formulate corresponding strategies in different regions under the new situation. We use ADF unit root test, E-G two-step cointegration test, Granger causality test, and other research methods in Eviews 5.0 statistical software, to empirically study the relationship between the cotton future price and cotton spot price in Xinjiang, the relationship between the cotton future price and cotton spot price in China. The results show that there is a long-term relationship between the cotton future price and cotton spot price in Xinjiang, between the cotton future price and cotton spot price in China; the cotton future price plays unidirectional role in guiding cotton spot price in Xinjiang and cotton spot price in China. The discovery function of cotton future price plays much greater role in the cotton market of China than in the cotton market of Xinjiang.

  12. A comparison of hemorrhage control and hydrogen peroxide generation in commercial and cotton-based wound dressing materials

    Science.gov (United States)

    Nonwoven UltraCleanTM Cotton (highly cleaned and hydroentangled, greige cotton) retains the native wax and pectin content (~2%) of the cotton fiber traditionally removed from scoured and bleached cotton gauze, yet potentially affording wound healing properties. In vitro thromboelastography, hydrog...

  13. The preparation and antibacterial effects of dopa-cotton/AgNPs

    International Nuclear Information System (INIS)

    Xu Hong; Shi Xue; Ma Hui; Lv Yihang; Zhang Linping; Mao Zhiping

    2011-01-01

    Silver nanoparticles (AgNPs) have been known to have powerful antibacterial activity. In this paper, in situ generation of AgNPs on the surface of dopamine modified cotton fabrics (dopa-cotton/AgNPs) in aqueous solution under room temperature is presented. X-ray photoelectron spectroscopy (XPS) and field emission scanning electron microscope (FE-SEM) were used to analyze the surface chemical composition and the morphology of the modified cotton fabrics, respectively. The results indicated that the surface of cotton fabrics was successfully coated with polydopamine and AgNPs. The cotton fabrics with AgNPs showed durable antibacterial activity.

  14. Inventories of Asian textile producers, US cotton exports, and the exchange rate

    Directory of Open Access Journals (Sweden)

    Durmaz Nazif

    2014-01-01

    Full Text Available The present paper develops a model with US cotton exports depending on the stock-to-use ratio, trade weighted exchange rates, and the relative cotton prices. The role of inventories in cotton consumption is examined in five textile producing cotton importers, China, Indonesia, Thailand, South Korea, and Taiwan. Cotton inventory dynamics is diverse among Asian textile producers. Relative prices have negative effect in all markets as expected. Exchange rate elasticities show that effects should be examined for each separate market. Changes in rates of depreciation also have stronger effects than exchange rate. Results reveal that these countries are not all that homogenous.

  15. A recepção da ginástica sueca em Portugal nas primeiras décadas do século XX: conformidades e dissensões culturais e políticas

    Directory of Open Access Journals (Sweden)

    Luís Miguel Carvalho

    2015-06-01

    Full Text Available O artigo aborda a presença persistente da "ginástica sueca" como referente principal da educação física em contexto escolar em Portugal, nas primeiras décadas do século XX, e as recepções distintas de que foi alvo. Numa primeira parte, o texto centra-se na compreensão da centralidade adquirida pela "ginástica sueca", em múltiplos contextos geopolíticos, no contexto da consolidação do projeto da escola de massas. Numa segunda parte, o texto documenta e analisa algumas deslocações interpretativas ocorridas na recepção da "ginástica sueca" em Portugal, entre 1920 e 1940, bem como os realinhamentos educativos, sociais e políticos que acompanharam esses conflitos sobre a sua "correta" mobilização para o contexto escolar português.

  16. El Manuscrito Cerramientos y trazas de montea de Ginés Martínez de Aranda

    Directory of Open Access Journals (Sweden)

    Calvo López, José

    2009-03-01

    Full Text Available Ginés Martínez de Aranda, master mason in the cathedrals of Cádiz and Santiago de Compostela during the late 16th century, wrote a manuscript, Cerramientos y trazas de montea, concerning geometrical problems in stone construction. This article deals with the copy of Cerramientos in the Servicio Histórico Militar (Madrid, its copyist, dating, the existence of an earlier version and whether or not Aranda intended to publish it. Also examined are the connections between Cerramientos and other Spanish stonecutting texts of the period, such as those by Alonso de Vandelvira, Cristóbal de Rojas, Alonso de Guardia or Juan de Portor y Castro. Finally, an assessment is made of Martínez de Aranda’s original contributions to European stonecutting literatura.

    El arquitecto y cantero baezano Ginés Martínez de Aranda, que trabajó a finales del siglo XVI y ejerció la maestría de las catedrales de Cádiz y Santiago de Compostela, compuso un manuscrito llamado Cerramientos y trazas de montea, que trata de los problemas geométricos de la construcción pétrea. El artículo analiza la copia del manuscrito conservada en el Servicio Histórico Militar de Madrid, la identidad del copista, la fecha de la primera redacción de la obra y la de la copia conservada, y el destino de la obra; a continuación, se estudia la relación del manuscrito con otras obras españolas de cantería, en especial las de Alonso de Vandelvira, Cristóbal de Rojas, Alonso de Guardia y Juan de Portor y Castro, para finalizar tratando diversas aportaciones originales de Aranda a la literatura europea de la cantería.

  17. Thermal reduction of graphene-oxide-coated cotton for oil and organic solvent removal

    International Nuclear Information System (INIS)

    Hoai, Nguyen To; Sang, Nguyen Nhat; Hoang, Tran Dinh

    2017-01-01

    Highlights: • A new method for preparation of reduced-graphene-oxide (RGO) coated cotton is proposed. • The RGO-Cotton composites were carefully characterized using many modern techniques. • RGO-Cotton exhibited superhydrophobicity and superolephilicity. • RGO-Cotton sponges can absorb many types of oils and organic solvents and can be recycled. - Abstract: The reduced-graphene-oxide (RGO)-coated cotton sponge (RGO-Cot) was prepared by simply heating a graphene-oxide (GO)-coated cotton sponge, which was fabricated by dipping a commercial cotton sponge into a GO dispersion, under vacuum at 200 °C for 2 h. The thus prepared RGO-Cot sponges exhibited superhydrophobicity and superoleophilicity, with a water contact angle of 151°. These RGO-Cot sponges could be used for removal of many types of oils and organic solvents as they exhibit absorption capacities in the range of 22–45 times their weight and good absorption recyclability.

  18. Thermal reduction of graphene-oxide-coated cotton for oil and organic solvent removal

    Energy Technology Data Exchange (ETDEWEB)

    Hoai, Nguyen To, E-mail: hoaito@pvu.edu.vn; Sang, Nguyen Nhat; Hoang, Tran Dinh

    2017-02-15

    Highlights: • A new method for preparation of reduced-graphene-oxide (RGO) coated cotton is proposed. • The RGO-Cotton composites were carefully characterized using many modern techniques. • RGO-Cotton exhibited superhydrophobicity and superolephilicity. • RGO-Cotton sponges can absorb many types of oils and organic solvents and can be recycled. - Abstract: The reduced-graphene-oxide (RGO)-coated cotton sponge (RGO-Cot) was prepared by simply heating a graphene-oxide (GO)-coated cotton sponge, which was fabricated by dipping a commercial cotton sponge into a GO dispersion, under vacuum at 200 °C for 2 h. The thus prepared RGO-Cot sponges exhibited superhydrophobicity and superoleophilicity, with a water contact angle of 151°. These RGO-Cot sponges could be used for removal of many types of oils and organic solvents as they exhibit absorption capacities in the range of 22–45 times their weight and good absorption recyclability.

  19. The complete genome sequence of a virus associated with cotton blue disease, cotton leafroll dwarf virus, confirms that it is a new member of the genus Polerovirus.

    Science.gov (United States)

    Distéfano, Ana J; Bonacic Kresic, Ivan; Hopp, H Esteban

    2010-11-01

    Cotton blue disease is the most important virus disease of cotton in the southern part of America. The complete nucleotide sequence of the ssRNA genome of the cotton blue disease-associated virus was determined for the first time. It comprised 5,866 nucleotides, and the deduced genomic organization resembled that of members of the genus Polerovirus. Sequence homology comparison and phylogenetic analysis confirm that this virus (previous proposed name cotton leafroll dwarf virus) is a member of a new species within the genus Polerovirus.

  20. [Effects of transgenic Bt + CpTI cotton on rhizosphere bacteria and ammonia oxidizing bacteria population].

    Science.gov (United States)

    Dong, Lianhua; Meng, Ying; Wang, Jing

    2014-03-04

    The effect of transgenic cotton on the rhizosphere bacteria can be important to the risk assessment for the genetically modified crops. We studied the rhizosphere microbial community with cultivating genetically modified cotton. The effects of transgenic Bt + CpTI Cotton (SGK321) and its receptor cotton (SY321) on rhizosphere total bacteria and ammonia oxidizing bacteria population size were studied by using droplet digital PCR. We collected rhizosphere soil before cotton planting and along with the cotton growth stage (squaring stage, flowering stage, belling stage and boll opening stage). There was no significant change on the total bacterial population between the transgenic cotton and the receptor cotton along with the growth stage. However, the abundance of ammonia oxidizing bacteria (AOB) in both type of cottons showed significant difference between different growth stages, and the variation tendency was different. In squaring stage, the numbers of AOB in rhizosphere of SY321 and SGK321 increased 4 and 2 times, respectively. In flowering stage, AOB number in rhizosphere of SY321 significantly decreased to be 5.96 x 10(5) copies/g dry soil, however, that of SGK321 increased to be 1.25 x 10(6) copies/g dry soil. In belling stage, AOB number of SY321 greatly increased to be 1.49 x 10(6) copies/g dry soil, but no significant change was observed for AOB number of SGK321. In boll opening stage, both AOB number of SY321 and SGK321 clearly decreased and they were significantly different from each other. Compared to the non-genetically modified cotton, the change in abundance of ammonia oxidizing bacteria was slightly smooth in the transgenic cotton. Not only the cotton growth stage but also the cotton type caused this difference. The transgenic cotton can slow down the speed of ammonia transformation through impacting the number of AOB, which is advantageous for plant growth.

  1. APPLICATION OF DRIP IRRIGATION ON COTTON PLANT GROWTH (Gossypium sp.

    Directory of Open Access Journals (Sweden)

    Syahruni Thamrin

    2017-12-01

    Full Text Available The condition of cotton planting in South Sulawesi is always constrained in the fulfillment of water. All plant growth stages are not optimal to increase production, so it is necessary to introduce good water management technology, such as through water supply with drip irrigation system. This study aims to analyze the strategy of irrigation management in cotton plants using drip irrigation system. Model of application by designing drip irrigation system and cotton planting on land prepared as demonstration plot. Observations were made in the germination phase and the vegetative phase of the early plants. Based on the result of drip irrigation design, the emitter droplet rate (EDR was 34.266 mm/hour with an operational time of 4.08 min/day. From the observation of cotton growth, it is known that germination time lasted from 6 to 13 days after planting, the average plant height reached 119.66 cm, with the number of leaves averaging 141.93 pieces and the number of bolls averaging 57.16 boll.

  2. Wash fastness improvement of malachite green-dyed cotton fabrics ...

    Indian Academy of Sciences (India)

    Administrator

    Nano-size features of both silica and titania nanosols are predicted to enhance the wash fastness of ... The cotton fabric was obtained from traditional market and was previously tested to contain fully cellulose ..... The authors acknowledge financial support of DP2M,. Directorate General of Higher Education, Indonesia,.

  3. Detecting cotton boll rot with an electronic nose

    Science.gov (United States)

    South Carolina Boll Rot is an emerging disease of cotton, Gossypium hirsutum L., caused by the opportunistic bacteria, Pantoea agglomerans (Ewing and Fife). Unlike typical fungal diseases, bolls infected with P. agglomerans continue to appear normal externally, complicating early and rapid detectio...

  4. Application of grafted polynomial function in forecasting cotton ...

    African Journals Online (AJOL)

    A study was conducted to forecast cotton production trend with the application of a grafted polynomial function in Nigeria from 1985 through 2013. Grafted models are used in econometrics to embark on economic analysis involving time series. In economic time series, the paucity of data and their availability has always ...

  5. The performance of cutinase and pectinase in cotton scouring

    NARCIS (Netherlands)

    Agrawal, Pramod

    2005-01-01

    Advances in biotechnology and enzymology have brought new lines of research and have accelerated the development of enzymatic applications in wet textile processing for now nearly one decade. Amongst the various stages of cotton preparation, wet textile processing is a highly energy, water and

  6. compressibility characteristics of compacted black cotton soil treated

    African Journals Online (AJOL)

    eobe

    E-mail addresses: 1111 aeberemu@yahoo.com, 2222sadat1010@live.com. Abstract. One dimensional consolidation studies on compacted black cotton soil treated with up to 16% rice .... 80% of the organic matter of the husk is burnt off and.

  7. Wireless sensor network for irrigation application in cotton

    Science.gov (United States)

    A wireless sensor network was deployed in a cotton field to monitor soil water status for irrigation. The network included two systems, a Decagon system and a microcontroller-based system. The Decagon system consists of soil volumetric water-content sensors, wireless data loggers, and a central data...

  8. Multiple shoot regeneration of cotton (Gossypium hirsutum L.) via ...

    African Journals Online (AJOL)

    user

    2011-03-14

    Mar 14, 2011 ... Induction of multiple shoots of cotton (Gossypium hirsutum L.) plant in two commercial varieties (Sahel and Varamin) using shoot apex was done. Explants were isolated from 3 - 4 days old seedlings, then they were cultured on a shoot induction media, modified MS nutrient agar with combinations: 1- ...

  9. Impact of Bollgard ® genetically modified cotton on the biodiversity ...

    African Journals Online (AJOL)

    Using cotton cultivars that express a gene of the Bacillus thuringiensis (Bt) bacterium producing a protein (Cry1Ac) with an insecticide effect on the Lepidoptera pests has made it possible to reduce the number of insecticide applications during the crop cycle. Thus, the objective was to determine, in the field during the ...

  10. Analysis Of The Reactivity Of Radpro Solution With Cotton Rags

    International Nuclear Information System (INIS)

    Marusich, R.M.

    2009-01-01

    Rags containing RadPro(reg s ign) solution will be generated during the decontamination of the Plutonium Finishing Plant (PFP). Under normal conditions, the rags will be neutralized with sodium carbonate prior to placing in the drums. The concern with RadPro solutions and cotton rags is that some of the RadPro solutions contain nitric acid. Under the right conditions, nitric acid and cotton rags exothermically react. The concern is, will RadPro solutions react with cotton rags exothermically? The potential for a runaway reaction for any of the RadPro solutions used was studied in Section 5.2 of PNNL-15410, Thermal Stability Studies of Candidate Decontamination Agents for Hanford's Plutonium Finishing Plant Plutonium-Contaminated Gloveboxes. This report shows the thermal behavior of cotton rags having been saturated in one of the various neutralized and non-neutralized RadPro solutions. The thermal analysis was performed using thermogravimetric Analysis (TGA), Differential Thermal Analysis (DTA) and Accelerating Rate Calorimetry (ARC).

  11. Drought coping strategies in cotton: increased crop per drop.

    Science.gov (United States)

    Ullah, Abid; Sun, Heng; Yang, Xiyan; Zhang, Xianlong

    2017-03-01

    The growth and yield of many crops, including cotton, are affected by water deficit. Cotton has evolved drought specific as well as general morpho-physiological, biochemical and molecular responses to drought stress, which are discussed in this review. The key physiological responses against drought stress in cotton, including stomata closing, root development, cellular adaptations, photosynthesis, abscisic acid (ABA) and jasmonic acid (JA) production and reactive oxygen species (ROS) scavenging, have been identified by researchers. Drought stress induces the expression of stress-related transcription factors and genes, such as ROS scavenging, ABA or mitogen-activated protein kinases (MAPK) signalling genes, which activate various drought-related pathways to induce tolerance in the plant. It is crucial to elucidate and induce drought-tolerant traits via quantitative trait loci (QTL) analysis, transgenic approaches and exogenous application of substances. The current review article highlights the natural as well as engineered drought tolerance strategies in cotton. © 2017 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

  12. Performance of fertigation technique for phosphorus application in cotton

    Directory of Open Access Journals (Sweden)

    M. Aslam

    2009-05-01

    Full Text Available Low native soil phosphorus availability coupled with poor utilization of added phosphorus is one of the major constraints limiting the productivity of the crops. With a view of addressing this issue, field studies were conducted to compare the relative efficacy of broadcast and fertigation techniques for phosphorus application during 2005-2006 using cotton as a test crop. Two methods of phosphorus application i.e. broadcast and fertigation were evaluated using five levels of P2O5 (0, 30, 45, 60 and 75 kg P2O5 ha -1. Fertigation showed an edge over broadcast method at all levels of phosphorus application. The highest seed cotton yield was recorded with 75 kg P2O5 ha-1. Fertilizer phosphorus applied at the rate of 60 kg ha-1 through fertigation produced 3.4 tons ha-1 of seed cotton yield, which was statistically identical to 3.3 tons recorded with 75 kg ha-1 of broadcast phosphorus. Agronomic performance of phosphorus was influenced considerably by either method of fertilizer application. The seed cotton yield per kg of fertigation phosphorus was 48% higher than the corresponding broadcast application. The results of these studies showed that fertigation was the most efficient method of phosphorus application compared with the conventional broadcast application of fertilizers.

  13. Site Suitability For Yam, Rice And Cotton Production In Adamawa ...

    African Journals Online (AJOL)

    This paper demonstrated the potentials of GIS technique for mapping and delineating the suitable sites for Yam, Rice and Cotton production in Adamawa State. Site suitability mapping is necessary to create data bank and to guide the farmers in decision making on sites for crop production in the state. The use of GIS for this ...

  14. Review: Genetic diversity and population structure of cotton ...

    African Journals Online (AJOL)

    Cotton (Gossypium spp.) is the world's leading natural fiber crop and is cultivated in diverse temperate and tropical areas. In this sense, molecular markers are important tools for polymorphism identification in genetic diversity analyses. The objective of this study was to evaluate genetic diversity and population structure in ...

  15. Yield evaluation and stability analysis in newly selected `KSA' cotton ...

    African Journals Online (AJOL)

    Yield evaluation and stability analysis in newly selected `KSA' cotton cultivars in Western Kenya. R M Opondo, G A Ombakho. Abstract. (African Crop Science Journal, 1997 5(2): 119-126). http://dx.doi.org/10.4314/acsj.v5i2.27854 · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians ...

  16. Distribution and Potential Impact of Feral Cotton on the ...

    African Journals Online (AJOL)

    Transgenic Bt cotton with insecticidal properties presents a potential solution to the bollworm infestation in Tanzania. However, concerns associated with transgenic crops viz.; transgene flow to wild and feral relatives, increased potential for resistance evolution, need to be addressed prior to adoption of any transgenic crop.

  17. Use of induced mutations for cotton breeding in India

    International Nuclear Information System (INIS)

    Raut, R.N.

    1980-01-01

    A large number of studies have been reported in recent years on the use of induced mutations in the improvement of food crops and ornamentals. Similar investigations on fibre crops like cotton have, however, been relatively few. The fact that most of the economically useful characters in cotton are under polygenic control appears to be the main limiting factor. Inspite of this there are reports of radiation induced useful mutations used as commercial varieties. As early as 1950 a X-ray induced mutant variety of G. hirsutum cotton Indore-2 was released for commercial cultivation in Madhya Pradesh and covered more than one lac hectares. More recently an early maturing mutant variety MCU-7 was released for cultivation in summer rice fallows of Tamil Nadu and covers nearly 10,000 acres. Other promising mutant strains found suitable b.v large scale trials and recommended for cultivation under specific conditions are Okra leaf mutant, photoinsensitive mutant of MCU-5 (named Rasmi) and Jassid tolerant early maturing mutant 4-1 (Pusa Ageti). In addition improved varieties like Badnaawar-1, Khandwa-2 and M64 have been evolved by utilizing mutant lines in cross breeding. The scope of induced mutation method as a breeding technique for cotton improvement in India is very wide. (author)

  18. KUTUN : a morphogenetic model for cotton (Gossypium hirsitum L.)

    NARCIS (Netherlands)

    Mutsaers, H.J.W.

    1982-01-01

    A whole crop model for growth and development of cotton ( Gossypium hirsutum L.) is presented. The model is based on previous extensive studies on plant morphogenesis, growth of fruits and canopy photosynthesis. The crop model basically is a carbohydrate budget, but all

  19. Site specific N application and remote sensing of cotton crop

    Science.gov (United States)

    A spatial variable nitrogen (N) rate trial and remote sensing of cotton crop was conducted during 2003 at Paul Good Farms, Mississippi, USA. The N rate trial consisted of three, 8-row transects at the east and west side of the field that were selected to represent variable soil and elevation feature...

  20. Is Hedging a Habit? Hedging Ratio Determination of Cotton Producers

    NARCIS (Netherlands)

    Dorfman, J.H.; Pennings, J.M.E.; Garcia, P.

    2010-01-01

    We examine the role that habit plays when producers determine their hedge ratio. Data were collected from U.S. cotton growers in which they indicated their hedging position in 2001 and 2002 as well as their perceived profitability, land ownership structure, and income. To account for heterogeneity,

  1. Nuclear ribosomal DNA diversity of a cotton pest ( Rotylenchulus ...

    African Journals Online (AJOL)

    The reniform nematode (Rotylenchulus reniformis) has emerged as a major cotton pest in the United States. A recent analysis of over 20 amphimictic populations of this pest from the US and three other countries has shown no sequence variation at the nuclear ribosomal internal transcribed spacer (ITS) despite the region's ...

  2. Mechanical Characterization of Cotton Fiber/Polyester Composite Material

    Directory of Open Access Journals (Sweden)

    Altaf Hussain Rajper

    2014-04-01

    Full Text Available Development of composite from natural fiber for lower structural application is growing for long-term sustainable perspective. Cotton fiber composite material has the added advantages of high specific strength, corrosion resistance, low cost and low weight compared to glass fiber on the expense of internal components of IC engines. The primary aim of the research study is to examine the effect of the cotton fiber on mechanical properties of lower structural applications when added with the polyester resin. In this paper composite material sample has been prepared by hand Lay-Up process. A mould is locally developed in the laboratory for test sample preparation. Initially samples of polyester resin with appropriate ratio of the hardener were developed and tested. At the second stage yarns of cotton fiber were mixed with the polyester resin and sample specimens were developed and tested. Relative effect of the cotton as reinforcing agent was examined and observed that developed composite specimen possess significant improvement in mechanical properties such as tensile strength was improved as 19.78 % and modulus of elasticity was increased up to 24.81%. Through this research it was also observed that developed composite material was of ductile nature and its density decreases up to 2.6%. Results from this study were compared with relevant available advanced composite materials and found improved mechanical properties of developed composite material

  3. Profitability of cover crops for single and twin row cotton

    Science.gov (United States)

    With the increased interest in cover crops, the impact of adoption on profitability of cash crops is a common question from producers. The objective of this study was to evaluate the profitability of cover crops for single and twin row cotton (Gossypium hirsutum L.) in Alabama. This experiment inclu...

  4. Effect of nitrates on embryo induction efficiency in cotton ...

    African Journals Online (AJOL)

    Cotton (Gossypium hirsutum L.) cv Coker-312 callus culture was assessed in terms of its usefulness as a system for investigating the effect of nitrates from different chemical compounds of nitrogen on embryo induction percentage in calli as the plant growth and cell differentiation mainly based on nitrogen. Both sources and ...

  5. Flavonoid biosynthesis controls fiber color in naturally colored cotton

    Directory of Open Access Journals (Sweden)

    Hai-Feng Liu

    2018-04-01

    Full Text Available The existence of only natural brown and green cotton fibers (BCF and GCF, respectively, as well as poor fiber quality, limits the use of naturally colored cotton (Gossypium hirsutum L.. A better understanding of fiber pigment regulation is needed to surmount these obstacles. In this work, transcriptome analysis and quantitative reverse transcription PCR revealed that 13 and 9 phenylpropanoid (metabolic pathway genes were enriched during pigment synthesis, while the differential expression of phenylpropanoid (metabolic and flavonoid metabolic pathway genes occurred among BCF, GCF, and white cotton fibers (WCF. Silencing the chalcone flavanone isomerase gene in a BCF line resulted in three fiber phenotypes among offspring of the RNAi lines: BCF, almost WCF, and GCF. The lines with almost WCF suppressed chalcone flavanone isomerase, while the lines with GCF highly expressed the glucosyl transferase (3GT gene. Overexpression of the Gh3GT or Arabidopsis thaliana 3GT gene in BCF lines resulted in GCF. Additionally, the phenylpropanoid and flavonoid metabolites of BCF and GCF were significantly higher than those of WCF as assessed by a metabolomics analysis. Thus, the flavonoid biosynthetic pathway controls both brown and green pigmentation processes. Like natural colored fibers, the transgenic colored fibers were weaker and shorter than WCF. This study shows the potential of flavonoid pathway modifications to alter cotton fibers’ color and quality.

  6. Catalytic bleaching of cotton: molecular and macroscopic aspects

    NARCIS (Netherlands)

    Topalovic, T.

    2007-01-01

    The scope of this thesis was to investigate the possibility of low-temperature cotton bleaching employing dinuclear tri- -oxo bridged manganese(IV) complex of the ligand 1,4,7-trimethyl-1,4,7-triazacyclononane (MnTACN) as the catalyst in the system with hydrogen peroxide. With this objective in

  7. Evaluation of cotton stalk hydrolysate for xylitol production.

    Science.gov (United States)

    Sapcı, Burcu; Akpinar, Ozlem; Bolukbasi, Ufuk; Yilmaz, Levent

    2016-07-03

    Cotton stalk is a widely distributed and abundant lignocellulosic waste found in Turkey. Because of its rich xylose content, it can be a promising source for the production of xylitol. Xylitol can be produced by chemical or biotechnological methods. Because the biotechnological method is a simple process with great substrate specificity and low energy requirements, it is more of an economic alternative for the xylitol production. This study aimed to use cotton stalk for the production of xylitol with Candida tropicalis Kuen 1022. For this purpose, the combined effects of different oxygen concentration, inoculum level and substrate concentration were investigated to obtain high xylitol yield and volumetric xylitol production rate. Candida tropicalis Kuen 1022 afforded different concentrations of xylitol depending on xylose concentration, inoculum level, and oxygen concentration. The optimum xylose, yeast concentration, and airflow rate for cotton stalk hydrolysate were found as 10.41 g L(-1), 0.99 g L(-1), and 1.02 vvm, respectively, and under these conditions, xylitol yield and volumetric xylitol production rate were obtained as 36% and 0.06 g L(-1) hr(-1), respectively. The results of this study show that cotton stalk can serve as a potential renewable source for the production of xylitol.

  8. Cotton photosynthetic regulation through nutrient and water availability

    Science.gov (United States)

    Photosynthesis is an extremely complicated process that is fundamental to supporting plant growth. It is regulated by multiple internal and external factors. Three factors regulating photosynthesis over which cotton producers can exert some influence are the levels of nitrogen, potassium, and soil...

  9. Identification of resistance to Aspergillus flavus infection in cotton germplasm

    Science.gov (United States)

    Natural resistance of in cottonseed to Aspergillus flavus infection has not been explored to date. A green fluorescent protein (GFP) expressing -70 strain was used to assess the resistance of seed from thirty five35 cotton varieties including representatives from Gossypium arboreum, G. barbadense, a...

  10. The Commodification and Underdevelopment of Ishan Cotton in ...

    African Journals Online (AJOL)

    The paper concluded that the root cause of Nigeria's post-imperial dependence on imported textile and cotton products is the result of the non-development of cash crops in backwards integration. It recommended the qualitative transformation of indigenous skills and resources to animate the spirit of local enterprise.

  11. Sugar alcohols-induced oxidative metabolism in cotton callus culture

    African Journals Online (AJOL)

    Sugar alcohols (mannitol and sorbitol) may cause oxidative damage in plants if used in higher concentration. Our present experiment was undertaken to study physiological and metabolic responses in cotton (Gossypium hirsutum L.) callus against mannitol and sorbitol higher doses. Both markedly declined mean values of ...

  12. Role of secondary metabolites biosynthesis in resistance to cotton ...

    African Journals Online (AJOL)

    Secondary metabolites production in healthy and diseased sample of leaves of cotton varieties after the attack of CLCuV found maximum phenolics, carotenoids, chlorophyll a, chlorophyll b and total chlorophyll a and b in healthy sample and minimum contents present in diseased sample. CIM-446 was the best variety to ...

  13. TURKISH TRADE POLICY AND THE EFFICIENCY OF TURKISH COTTON MARKETS

    OpenAIRE

    Schmitz, Troy G.

    1999-01-01

    Turkish cotton markets are affected by import duties, export taxes, and a range of domestic subsidies. The degree of economic inefficiency arising from these government policies is estimated through the use of two partial equilibrium models, one for the Aegean market and another for the non-Aegean market. The welfare implications of these policies are also explored.

  14. Efeitos do "feedback" autocontrolado na aprendizagem do lançamento da bola da ginástica rítmica

    Directory of Open Access Journals (Sweden)

    Anielle Lemos

    2013-09-01

    Full Text Available O objetivo do presente estudo foi investigar os efeitos da frequência autocontrolada de "feedback" na aprendizagem do lançamento da bola da ginástica rítmica. A amostra foi constituída de 24 crianças, de sete a 10 anos de idade, distribuídas em dois grupos em relação aos diferentes tipos de condições de "feedback": autocontrolado e externamente controlado. O estudo foi composto de uma fase de prática e um teste de retenção. Os resultados de um questionário revelaram que a maioria dos participantes do grupo autocontrolado solicitou "feedback" principalmente após as boas tentativas de prática, enquanto os participantes do grupo "yoked" indicaram ter recebido "feedback" nas tentativas em que o desejavam. Nenhuma diferença foi encontrada em relação ao desempenho ou aprendizagem. Conclui-se que a frequência autocontrolada de "feedback" é tão eficiente quanto a frequência externamente controlada na aprendizagem da habilidade motora específica lançamento do aparelho bola em crianças desta faixa etária.

  15. Desequilíbrio hormonal e disfunção menstrual em atletas de ginástica rítmica

    Directory of Open Access Journals (Sweden)

    Sabrina Macedo Hott Coelho

    2015-09-01

    Full Text Available ResumoObjetivou-se avaliar a magnitude das alterações de hormônios reguladores do ciclo menstrual (CM e testosterona de atletas de ginástica rítmica (GR de alto rendimento, em período pré-competitivo para a Olimpíada de Beijing. Foram realizadas coletas de sangue em 4 momentos, com intervalos de 7 dias. Os hormônios estrogênio, progesterona, luteinizante (LH, folículo estimulante (FSH e testosterona foram mensurados por quimioluminescência. As atletas (n = 7 relataram disfunção menstrual e houve expressiva variação hormonal intra e entre indivíduos. Das amostras de estrogênio, 65% ficaram abaixo do valor referencial clínico, enquanto que as concentrações de progesterona e LH ficaram próximas ao limite inferior. Para FSH e testosterona, 10% e 30% das amostras, respectivamente, ficaram abaixo do referencial. Conclui-se que atletas de alto rendimento em GR apresentam maior risco de desequilíbrio hormonal e disfunção menstrual, o que inspira necessidade de atenção clínica.

  16. Interação entre leptina, ginástica artística, puberdade e exercício em atletas do sexo feminino

    Directory of Open Access Journals (Sweden)

    Tatiana de Barros Meira

    2010-09-01

    Full Text Available Há evidências de que as atletas de ginástica artística (GA apresentam desregulações no sistema reprodutório em relação à média populacional. A interação entre alguns fatores pode explicar esse fato: genética, estresse do exercício, baixa porcentagem de gordura corporal, má nutrição e ação da leptina. Por meio de uma revisão de literatura, discutimos resultados de pesquisas que relacionam a ação do hormônio leptina e desregulações no sistema reprodutório durante a puberdade em atletas de GA do sexo feminino. Podemos afirmar que existe uma interação entre a seleção natural na modalidade, a baixa ingestão calórica e o estresse do treinamento, que ocasionaria a diminuição de leptina plasmática e causaria desregulações no sistema reprodutório durante a puberdade.

  17. Screening of cotton (gossypium hirsutum l.) genotypes for heat tolerance

    International Nuclear Information System (INIS)

    Abro, S.; Khan, M.A.; Sial, M.A.

    2015-01-01

    Cotton yield is highly affected due to biotic (diseases and pests) and abiotic (heat, dought and salinity) Stresses. Among them, high temperature is the main environmental constraint which adversely reduces cotton yield and quality. High temperature above 36 degree C affects plant growth and development especially during reproductive phase. Present studies were carried out to assess the tolerance of fifty-eight newly evolved cotton genotypes to heat stresses, based on agronomic and physiological characteristics. The genotypes were screened in field conditions under two temperature regimes. The studies were conducted at experimental farm of Nuclear Institute of Agriculture, Tando Jam, Pakistan. The results showed that March sown crop experienced high temperature (i.e. > 44 degree C in May and June), which significantly affected crop growth and productivity. The genotypes were identified as heat-tolerant on the basis of relative cell injury percentage (RCI %), heat susceptibility index (HSI) values, boll retention and seed cotton yield (kg/ha). RCI level in cotton genotypes ranged from 39.0 to 86.0%. Out of 58, seventeen genotypes (viz.NIA-80, NIA-81, NIA-83, NIA-84, NIA-M-30, NIA-M31, NIA-HM-48, NIA-HM-327, NIA-H-32, NIA-HM-2-1, NIA-Bt1, NIA-Bt2, NIA-Perkh, CRIS-342, CRIS-134, NIAB-111 and check variety Sadori indicated high level of heat tolerance at both (heat-stressed and non-stressed) temperature regimes; as shown the lowest relative injury level and relatively heat resistant index (HSI<1) values. Such genotypes could be used as heattolerant genotypes under heat-stressed environments. (author)

  18. Cotton fabrics with UV blocking properties through metal salts deposition

    International Nuclear Information System (INIS)

    Emam, Hossam E.; Bechtold, Thomas

    2015-01-01

    Graphical abstract: - Highlights: • Introducing metal salt based UV-blocking properties into cotton fabric. • A quite simple technique used to produce wash resistant UV-absorbers using different Cu-, Zn- and Ti-salts. • Good UPF was obtained after treatment with Cu and Ti salts, and ranged between 11.6 and 14. • The efficiency of the deposited metal oxides is compared on molar basis. - Abstract: Exposure to sunlight is important for human health as this increases the resistance to diverse pathogens, but the higher doses cause skin problems and diseases. Hence, wearing of sunlight protective fabrics displays a good solution for people working in open atmosphere. The current study offered quite simple and technically feasible ways to prepare good UV protection fabrics based on cotton. Metal salts including Zn, Cu and Ti were immobilized into cotton and oxidized cotton fabrics by using pad-dry-cure technique. Metal contents on fabrics were determined by AAS; the highest metal content was recorded for Cu-fabric and it was 360.6 mmol/kg after treatment of oxidized cotton with 0.5 M of copper nitrate. Ti contents on fabrics were ranged between 168.0 and 200.8 mmol/kg and it showed the lowest release as only 38.1–46.4% leached out fabrics after five laundry washings. Metal containing deposits were specified by scanning electron microscopy and energy dispersive X-ray spectroscopy. UV-transmission radiation over treated fabrics was measured and ultraviolet protection factor (UPF) was calculated. UPF was enhanced after treatment with Cu and Ti salts to be 11.6 and 14, respectively. After five washings, the amount of metal (Cu or Ti) retained indicates acceptable laundering durability.

  19. Artificial neural nets application in the cotton yarn industry

    Directory of Open Access Journals (Sweden)

    Gilberto Clóvis Antoneli

    2016-06-01

    Full Text Available The competitiveness in the yarn production sector has led companies to search for solutions to attain quality yarn at a low cost. Today, the difference between them, and thus the sector, is in the raw material, meaning processed cotton and its characteristics. There are many types of cotton with different characteristics due to its production region, harvest, storage and transportation. Yarn industries work with cotton mixtures, which makes it difficult to determine the quality of the yarn produced from the characteristics of the processed fibers. This study uses data from a conventional spinning, from a raw material made of 100% cotton, and presents a solution with artificial neural nets that determine the thread quality information, using the fibers’ characteristics values and settings of some process adjustments. In this solution a neural net of the type MultiLayer Perceptron with 11 entry neurons (8 characteristics of the fiber and 3 process adjustments, 7 output neurons (yarn quality and two types of training, Back propagation and Conjugate gradient descent. The selection and organization of the production data of the yarn industry of the cocamar® indústria de fios company are described, to apply the artificial neural nets developed. In the application of neural nets to determine yarn quality, one concludes that, although the ideal precision of absolute values is lacking, the presented solution represents an excellent tool to define yarn quality variations when modifying the raw material composition. The developed system enables a simulation to define the raw material percentage mixture to be processed in the plant using the information from the stocked cotton packs, thus obtaining a mixture that maintains the stability of the entire productive process.

  20. Zero tillage: A potential technology to improve cotton yield

    Directory of Open Access Journals (Sweden)

    Abbas Hafiz Ghazanfar

    2016-01-01

    Full Text Available Zero tillage technology revealed with no use of any soil inverting technique to grow crops. The crop plant seed is planted in the soil directly after irrigation to make the soil soft without any replenishing in soil layers. A study was conducted to evaluate cotton genotypes FH-114 and FH-142 for the consecutive three years of growing seasons from 2013-15. The seed of both genotypes was sown with two date of sowing, 1 March and 1 May of each three years of sowing under three tillage treatments (zero tillage, minimum tillage and conventional tillage in triplicate completely randomized split-split plot design. It was found from results that significant differences were recorded for tillage treatments, date of sowing, genotypes and their interactions. Multivariate analysis was performed to evaluate the yield and it attributed traits for potential of FH-114 and FH-142 cotton genotypes. The genotype FH-142 was found with higher and batter performance as compared to FH-114 under zero tillage, minimum tillage and conventional tillage techniques. The traits bolls per plant, boll weight, fibre fineness, fibre strength, plant height, cotton yield per plant and sympodial branches per plant were found as most contributing traits towards cotton yield and production. It was also found that FH-142 gives higher output in terms of economic gain under zero tillage with 54% increase as compared to conventional tillage technique. It was suggested that zero tillage technology should be adopted to improve cotton yield and quality. It was also recommended that further study to evaluate zero tillage as potential technology should be performed with different regions, climate and timing throughout the world.