Implementación TIC en la docencia universitaria: estudio de los esfuerzos en vigas = Implementing ITC in higher education: study of effort on beams

Directory of Open Access Journals (Sweden)

Alfonso Blasco Gutierrez

2017-04-01

Full Text Available En el presente artículo se presenta una práctica académica que aporta una visión de la evolución de los esfuerzos resultantes en vigas debido a las cargas concentradas o distribuidas en vigas isostáticamente apoyadas. Debido a la versatilidad del sistema se pueden realizar medidas dinámicas cambiando la disposición geométrica de la carga o su valor observando en tiempo real el cambio en los esfuerzos medidos. Por contraposición a las medidas clásicas de esfuerzos, consistentes en la sucesión de medidas estáticas costosas en tiempo y que suelen conllevar que los alumnos “desconecten” de la práctica, la capacidad de realizar medidas dinámicas permite que los alumnos adquieran una comprensión rápida y más intuitiva de cómo cambian los esfuerzos que afectan a la viga (elemento estructural en función de la carga. El coste de los materiales y la infraestructura necesarios para esta práctica es lo suficientemente bajo como para que sea posible su implementación en casi cualquier centro formativo. Abstract This work shows a new teaching practice focused on a better understanding of the efforts on beams, both owing to concentrated or distributed loads in isostatically supported beams. Due to the system versatility, it can obtain dynamic measurements changing the geometric arrangement of the load or its values. The system allows us to obtain, in real time, the measurements of efforts. By contrast to the classical measurements, that consist in the succession of static measures which during for so long and entail the students don’t pay attention to the practice. This ability to get dynamic measurements allows that students get an intuitive knowledge and a better understanding of how the efforts affect the beam (structural element versus the load. The cost of materials needed to carry out this practice and its own infrastructure is very low and because of that, is affordable for the most academic centers.

Intergranular stress corrosion in soldered joints of stainless steel 304.; Corrosion intergranular bajo esfuerzo en uniones soldadas de acero inoxidable 304

Energy Technology Data Exchange (ETDEWEB)

Zamora R, L [Instituto Nacional de Investigaciones Nucleares, Mexico City (Mexico)

1994-12-31

The intergranular stress cracking of welded joints of austenitic stainless steel, AISI 304, is a serious problem in BWR type reactors. It is associated with the simultaneous presence of three factors; stress, a critical media and sensibilization (DOS). EPR technique was used in order to verify the sensibilization degree in the base metal, and the zone affected by heat and welding material. The characterization of material was done. The objective of this work is the study of microstructure and the evaluation of EPR technique used for the determination of DOS in a welded plate of austenitic stainless steel AISI 304. (Author).

Suspensión retropúbica en mujeres con incontinencia urinaria de esfuerzo

Directory of Open Access Journals (Sweden)

Amparo Mirabal Fariñas

2014-09-01

Full Text Available Se efectuó un estudio descriptivo y transversal de 60 pacientes con incontinencia urinaria de esfuerzo, atendidas en la consulta de Urología del Hospital Provincial Docente Clinicoquirúrgico "Saturnino Lora Torres" de Santiago de Cuba, de enero del 2003 a igual mes del 2012, con vistas a evaluar la aplicación de la técnica quirúrgica de suspensión retropúbica en ellas. Entre los resultados relevantes de la serie figuraron: edad promedio de 50 años, incontinencia urinaria de esfuerzo de grados III (48,0 % y II (28,0 % y un elevado porcentaje de continencia posoperatoria inmediata (95,3. A los 3 meses de practicada la intervención, la continencia fue de 92,2 %, mientras que luego de 6 y 9 meses, se obtuvo una continencia de 87,5 %. Se concluyó que la suspensión retropúbica es un procedimiento de elevada efectividad para tratar pacientes con incontinencia urinaria de esfuerzo e incontinencia urinaria mixta, debido a su simple realización y las escasas complicaciones que se producen, lo cual incide favorablemente en la estadía hospitalaria

ESTUDIO DE LA RESISTENCIA MECÁNICA DE MATERIALES COMPUESTOS POLIMÉRICOS REFORZADOS CON FIBRAS DE CARBONO

Directory of Open Access Journals (Sweden)

Enrique Rocha-Rangel

2011-01-01

Full Text Available Materiales compuestos hechos de una resina epóxica reforzada con diferentes contenidos de fibra de carbono, fueron preparados por dos técnicas de laminación diferentes. Se aplicó 1 Kg/cm2 de presión en los laminados, mientras, que otros laminados se sometieron a un vacío de 1 atm. De los resultados se tiene que las resistencias a la flexión y tensión de los compósitos son mejoradas con el aumento en el contenido de fibra en los mismos. Los compósitos resultantes presentan un mejor comportamiento mecánico bajo esfuerzos de tensión que cuando lo hacen bajo esfuerzos de flexión, debido a que en flexión las fibras se rompen eventualmente, provocando que el material falle a bajos valores de esfuerzo. Cuando los materiales compuestos son sometidos a tensión, las fibras trasmiten los esfuerzos entre ellas y el material falla hasta que se acumula la energía necesaria para romper todas las fibras de una sola vez.

Modelo Neuronal de Estimación para el Esfuerzo de Desarrollo en Proyectos de Software (MONEPS

Directory of Open Access Journals (Sweden)

Mario G. Almache C, Geovanny Raura , Jenny A. Ruiz R., Efraín R. Fonseca C

2015-07-01

Full Text Available —La estimación temprana del esfuerzo para la construcción de un producto software, es crucial en la previsión del costo y tiempo necesarios para su desarrollo. Los modelos y técnicas para la estimación del esfuerzo presentan como principal inconveniente, la poca precisión en las predicciones realizadas y generalmente se hace una mínima consideración de los aspectos no funcionales del software. Se propone la construcción de un modelo de estimación para el esfuerzo en el desarrollo de software denominado MONEPS, que pretende mejorar la precisión en la estimación del esfuerzo, utilizando una Red Neuronal Artificial (RNA en Backpropagation, cuya capa de entrada se estructura sobre la base de un conjunto de características y atributos tomados de la norma ISO/IEC 25000 de la calidad del software. La RNA fue entrenada con datos recopilados de aplicaciones desarrolladas en el ámbito académico, de las cuales se conocían sus tiempos de desarrollo y costos asociados. Las estimaciones de tiempo y costo, para dos casos de prueba, muestran más precisión en el modelo neuronal, en comparación con los modelos Cocomo-81 y Cocomo-II. MONEPS ha logrado la convergencia de aspectos funcionales y no funcionales para mejorar la precisión en la estimación del esfuerzo en proyectos de software

Influencia de la sobremaduración en las propiedades mecánicas y comportamiento a corrosión bajo tensión de una aleación de aluminio 7075 T6

Directory of Open Access Journals (Sweden)

Badía, J. M.

2004-04-01

Full Text Available The effect of a reageing heat treatment following a T6 temper on the mechanical properties and the stress corrosion cracking behaviour (SCC on the EN AW 7075 aluminium alloy is studied. The reageing time was 27 hours for all the temperatures used: 147, 152 and 163 ºC; this last temperature is indicated in the MIL-H-6088F standard to obtain the T73 temper from the T6 temper. The mechanical properties and the stress corrosion behaviour are evaluated and, compared with the T6 and T73 tempers. The evolution of the microstructure is analysed with transmission electron microscopy (TEM and differential scanning calorimetry (DSC techniques, and related with the properties. The reageing following to the T6 temper made a more stable structure higher the temperature, and, consequently, lowing the stress corrosion susceptibility. For temperatures lower than 147 ºC, this diminution of stress corrosion susceptibility occurs without reducing the mechanical properties. So, the 147 ºC reageing heat treatment has better stress corrosion behaviour than the T6 temper, with similar mechanical properties. By the other hand, the stress corrosion susceptibility achieved with the 152 ºC reageing is slightly worse than the T73 one, but their mechanical properties are better.

En este trabajo se estudia el efecto de la aplicación de una etapa de remaduración posterior al estado T6 sobre las propiedades mecánicas y el comportamiento a corrosión bajo tensiones de una aleación EN AW 7075. Todas las remaduraciones se dieron durante 27 horas a tres temperaturas distintas: 147, 152 y 163 ºC; esta última corresponde a la indicada por la norma MIL-H-6088F para la obtención del estado T73 a partir del estado T6. Se evalúan las propiedades mecánicas y a corrosión bajo tensiones de estos tratamientos, teniendo como referencia los tratamientos T6 y T73. Se analiza la evolución de la microestructura con técnicas de microscopia electrónica de transmisión (TEM y

New fundamental and environmental aspects of atmospheric corrosion

Directory of Open Access Journals (Sweden)

Leygraf, C.

2009-06-01

Full Text Available Atmospheric corrosion involves chemical, electrochemical, and physical processes in three phases (solid, liquid, and gas and two interfaces (solid/liquid and liquid/gas. Because of inherent experimental and conceptual difficulties, scientific efforts to characterize this highly complex interfacial regime came relatively late into the field. With the access and development of surface and interface sensitive analytical techniques, it has lately become possible to perform molecular in situ analyses of the interfaces involved in atmospheric corrosion. This lecture presents some highlights from our fundamental research in atmospheric corrosion, performed at the Royal Institute of Technology in Stockholm, Sweden. It includes results from the most recent efforts in our research group to provide a molecular understanding of the interfacial regime that governs atmospheric corrosion. Using copper or zinc as substrate and carboxylic acid as corrosion stimulator in the humidity-containing atmosphere, results have been obtained with particular emphasis on probing the metal oxide/water interface (by infrared reflection absorption spectroscopy (IRAS combined with the quartz crystal microbalance (QCM and sum frequency generation (SFG and the water/gas interface (by SFG, respectively. While research in atmospheric corrosion traditionally has aimed at understanding how the environment influences the metal, the opposite question- how the metal influences the environment during atmospheric corrosion- may be of equally technical importance. Some examples of on-going research on new environmental aspects of atmospheric corrosion of zinc will also be presented.

La corrosión atmosférica implica procesos químicos, electroquímicos y físicos en tres fases (sólido, liquido y gas y dos interfases (sólido/líquido y líquido/gas. A causa de dificultades experimentales y conceptuales los esfuerzos científicos para caracterizar el proceso, interfacial

Un repaso de los conceptos sobre capacidad y esfuerzo fiscal, y su aplicación en los gobiernos locales mexicanos

Directory of Open Access Journals (Sweden)

Laura Sour

2008-01-01

Full Text Available En este estudio se revisan los métodos con que es posible calcular el esfuerzo y la capacidad fiscal de una región, y se demuestra que la falta de disponibilidad de información limita las posibilidades de examinar estos aspectos de las finanzas públicas. Se presentan además algunos de los esfuerzos teóricos y empíricos que se han realizado con la intención de brindar un panorama general sobre el tema. Se calcula el esfuerzo y la capacidad fiscal de 2 412 gobiernos locales de México para los años 1993 a 2004. Los resultados cuestionan el mito de que los gobiernos locales grandes suelen desarrollar un mayor esfuerzo fiscal ante la política de transferencias, sean éstas condicionadas o no condicionadas.

Comportamiento Mecánico Estático de los Instrumentos S1, S2, F1 de Protaper Universal® Bajo Torsión y Doblamiento. Análisis por Elementos Finitos

Directory of Open Access Journals (Sweden)

Luisa Fernanda Cartagena

2011-10-01

Full Text Available Propósito: Examinar el comportamiento mecánico estático de los instrumentos ProTaper Universal® S1, S2, F1 bajo torsión y doblamiento teniendo en cuenta las propiedades mecánicas del material, mediante el método de elementos finitos. Metodología: Estudio Observacional descriptivo. Las limas investigadas fueron S1, S2, F1 de ProTaper Universal®, modeladas con el software ANSYS 10 y sometidas a fuerzas de torsión empezando en 0.25N/cm hasta alcanzar el torque máximo recomendado por la casa comercial Maillefer® y doblamiento en un ángulo de 600. Resultados:El máximo esfuerzo ocurre en el núcleo de la sección para todos los instrumentos evaluados;  al incrementar el torque el  esfuerzo  se disipa a la periferia para S1 (D5, D10, D14, S2 (D5, D7, D8, D10, F1 (D2, D3, D5.  La lima S1 al ser sometida a  torsión en D0 y D5 independiente del torque que fuese aplicado el máximo de esfuerzo superaba el límite de deformación plástica en el núcleo de la sección  del instrumento. La lima S2 con torques de  1 ó 1,5 N/cm superó  el límite elástico del material. Lima F1 en D0, D2 con torques de  0.25, 0.5, 1, 1.5, 2 N/cm el esfuerzo máximo no supero el límite de deformación plástica. En la prueba de doblamiento la gran mayoría de la estructura de las limas S1, S2, F1, se encuentra  por debajo del esfuerzo de ruptura (línea neutral es bastante ancha.Conclusion: Las fuerzas de  torsión para todas la limas del estudio mostraron tener mayor riesgo de separación del instrumento en comparación con  las fuerzas de doblamiento. 

Asentamientos y esfuerzos verticales en suelos que soportan cargas verticales de distribución arbitraria

OpenAIRE

Rodríguez-Gutiérrez, J.; Aristizabal-Ochoa, J.

2004-01-01

Se propone un modelo para el cálculo de asentamientos y esfuerzos verticales en suelos sometidas a cargas verticales distribuidas en el plano horizontal en áreas de forma arbitraria. El modelo permite determinar los asentamientos elásticos o inelásticos y los esfuerzos verticales en cualquier un punto debajo del área cargada. Dos tipos de variación del módulo de elasticidad del suelo son utilizados: 1) el módulo varía linealmente con la profundidad; 2) el módulo varía con la intensidad del es...

La gestion bajo una cultura de calidad en Mexico: una verificacion empirica.

Directory of Open Access Journals (Sweden)

Rositas, J.

2004-07-01

Full Text Available El artículo presenta de entrada, enfoques administrativos que pueden ser englobados en el término “Gestión bajo una cultura de calidad” (GBCC, conocida internacionalmente como Total Quality Management [TQM], o simplemente Gestión de Calidad, citándose en seguida dos puntos de vista contrapunteados a nivel internacional en relación a este enfoque. Se presentan esfuerzos previos de consultores e implantadores mexicanos que, en base al método de casos y de generalizaciones empíricas de sus experiencias profesionales, consideran a la GBCC como una de las grandes tendencias y fuerzas de cambio en el siglo XXI. Se hace referencia a la escasez de investigaciones en las que se ponga a prueba estadísticamente los conceptos de teóricos, practicantes y consultores del área de la calidad. El autor propone y pone a prueba un modelo agregado de ecuaciones estructurales basado en datos de campo de su investigación de doctorado aportados por 45 empresas manufactureras mexicanas. El análisis de datos, realizado con los paquetes de software SPPS y AMOS, arroja coeficientes de regresión y de determinación, así como niveles de bondad del ajuste, altamente significativos. Al concluir, el autor sugiere estrategias adicionales para refinar futuros análisis de datos.

Tratamiento de la incontinencia urinaria de esfuerzo en la mujer, por la técnica de Perrin modificada

Directory of Open Access Journals (Sweden)

Edilberto Borges Cárdenas

1995-12-01

Full Text Available Se realizó un estudio prospectivo en 21 mujeres que presentaron incontinencia urinaria de esfuerzo, las cuales recibieron tratamiento quirúrgico por la técnica de Perrin modificada, en el Hospital General Docente "Guillermo Domínguez", del municipio Puerto Padre, en los años 1990 y 1991. Estas pacientes se siguieron después de operadas por espacio de 1 año, para evaluar los resultados mediatos obtenidos al aplicar esta técnica. Como principales resultados y conclusiones se expresan: la incontinencia urinaria de esfuerzo fue más frecuente después de la cuarta década de la vida, estuvo relacionada con la multiparidad y con el tipo de parto transpelviano; se encontró asociada con diversos grados de relajación pelviana, y resultaron los ligeros y medianos esfuerzos los que con mayor frecuencia la provocaron. Las pruebas de esfuerzo presentaron un alto grado de positividad. Técnicas quirúrgicas fallidas por vía vaginal, se recogieron como un antecedente importante. La retención urinaria fue la complicación posoperatoria más frecuente. El 95 % de los resultados mediatos alcanzados se evaluaron de satisfactorios

La energía humana el esfuerzo físico

Directory of Open Access Journals (Sweden)

Luis Suárez Flórez

1991-01-01

Full Text Available Se llama la atención sobre la energía humana, su importancia como elemento de productividad y como principio ó quizás como fin de la actividad deportiva. Se estudia el máximo esfuerzo físico, así como también algunos conceptos acerca de la energía aeróbica y la energía anaeróbica.

Determinación del centro de esfuerzo en un troquel de corte utilizando un programa CAD

OpenAIRE

BALDI DE COSTA, CLARA

2006-01-01

Se discute la importancia de la correcta ubicación del centro de esfuerzo en un troquel de corte para minimizar las cargas laterales sobre los , elementos de guía. Se describe el proceso matemático para determinar el centro de esfuerzo a través del cálculo del centroide de una curva, y sucesivamente se proporciona un método de aproximación que utiliza la capacidad de AutoCAD de calcular el centroide de una región plana bidimensional. The importance of a correct positioning of the force cen...

EL CONTROL DE LA INTENSIDAD DEL ESFUERZO Y SU INCIDENCIA SOBRE LA ACTIVIDAD FÍSICA EN EDAD ESCOLAR

Directory of Open Access Journals (Sweden)

Borja Sañudo Corrales

2007-01-01

Full Text Available El objetivo del presente estudio fue dotar a los alumnos de una herramienta que les permitiese controlar la intensidad de su actividad física utilizando para ello la valoración subjetiva del esfuerzo. 32 sujetos (n1=12 niños y n2=20 niñas de 11,5 ± 0,5 años participaron en un programa de entrenamiento en circuito integrado por seis postas. Se registró la frecuencia cardiaca con pulsómetros y la percepción subjetiva del esfuerzo mediante la escala OMNI. Tras las siete sesiones del programa se observaron correlaciones muy altas entre ambos parámetros (r=0,54-0,76. Una vez finalizado el estudio los alumnos fueron capaces de regular su esfuerzo dentro de un rango de frecuencia cardiaca establecido en un 53,13% respecto a la frecuencia cardiaca percibida y 56,25% respecto a la frecuencia cardiaca medida, facilitándoles así un procedimiento práctico para el control de la intensidad durante la actividad física.

Validez y reproducibilidad de la velocidad de desplazamiento de las cargas como indicador del carácter del esfuerzo

OpenAIRE

Martínez Cava, Alejandro

2015-01-01

Estudios recientes han constatado que evitar alcanzar la repetición de fallo muscular durante el entrenamiento de fuerza, y más concretamente controlar el número de repeticiones que se dejan de completar en cada serie de esfuerzo, es la estrategia más acertada para optimizar las adaptaciones neuromusculares y fisiológicas de los deportistas. No obstante, hasta la fecha el atleta únicamente dispone de la percepción subjetiva del esfuerzo que está realizando para detener la serie de repeticione...

Shrinkage behaviour and related corrosion performance of low-pH cementitious materials based on OPC or CAC

Directory of Open Access Journals (Sweden)

García-Calvo, J. L.

2016-03-01

Full Text Available Prior to using low-pH cementitious materials in underground repositories for high level waste, the characteristics determining their long-term durability must be analysed in depth. In this sense, different shrinkage tests have been made on mortar and concrete specimens using low-pH cement formulations based on ordinary portland cement (OPC or calcium aluminate cement (CAC, with high mineral admixtures contents. They showed similar autogenous shrinkage than samples without mineral admixtures but higher drying shrinkage when materials based on OPC with high silica fume contents were considered. Besides, as the use of reinforced concrete could be required in underground repositories, the susceptibility of reinforcement to corrosion when using low-pH cementitious materials based on OPC was analyzed, considering carbon steel and galvanized steel. In the formers corrosion was detected due to the low pore solution pH but any problem was detected when galvanized reinforcement were used.Previo al empleo de materiales con cementos de bajo pH en almacenamientos geológicos profundos (AGP de residuos radiactivos de alta actividad, características relacionadas con su durabilidad a largo plazo deben ser verificadas. Así, su estabilidad volumétrica se ha analizado en morteros y hormigones de bajo pH basados en OPC o CAC, con elevados contenidos de adiciones minerales. Estos presentaron retracciones autógenas similares a las medidas en materiales convencionales, pero retracciones por secado mayores en los basados en OPC y altos contenidos de humo de sílice. Dado que en zonas de los AGP podría emplearse hormigón armado, también se evaluó la susceptibilidad a la corrosión de aceros al carbono y aceros galvanizados en materiales de bajo pH basados en OPC. Se detectó un inicio temprano de corrosión en los primeros debido al bajo pH presente en el fluido de los poros de estos materiales, sin detectarse problemas al emplear aceros galvanizados.

Dictionary corrosion and corrosion control

International Nuclear Information System (INIS)

1985-01-01

This dictionary has 13000 entries in both languages. Keywords and extensive accompanying information simplify the choice of word for the user. The following topics are covered: Theoretical principles of corrosion; Corrosion of the metals and alloys most frequently used in engineering. Types of corrosion - (chemical-, electro-chemical, biological corrosion); forms of corrosion (superficial, pitting, selective, intercrystalline and stress corrosion; vibrational corrosion cracking); erosion and cavitation. Methods of corrosion control (material selection, temporary corrosion protection media, paint and plastics coatings, electro-chemical coatings, corrosion prevention by treatment of the corrosive media); Corrosion testing methods. (orig./HP) [de

The intangible legacy of the Indonesian Bajo

Directory of Open Access Journals (Sweden)

Chandra Nuraini

2016-05-01

Full Text Available The Sama-Bajau, or Bajo diaspora, extends from the southern Philippines and Sabah (Malaysian Borneo to the eastern part of Indonesia. The Indonesian Bajo, now scattered along the coasts of Sulawesi (Celebes and East Kalimantan, the Eastern Lesser Sunda Islands and Maluku, were once mostly nomadic fishermen of the sea or ocean freight carriers. Today, the Bajo are almost all fishermen and settled. Their former and present ways of life made them favour intangible forms of culture: it is impossible to transport bulky artefacts when moving frequently by boat, or when living in stilt houses, very close to the sea or on a reef. It is therefore an intangible legacy that is the essence of the Bajo’s culture. Sandro healers have a vast range of expertise that allows them to protect and heal people when they suffer from natural or supernatural diseases. On the other hand, music and especially oral literature are very rich. In addition to song and the pantun poetry contests, the most prestigious genre is the iko-iko, long epic songs that the Bajo consider to be historical rather than fictional narratives. The Bajo’s intangible heritage is fragile, since it is based on oral transmission. In this article, I give a description of this heritage, dividing it into two areas: the knowledge that allows them to “protect and heal” on the one hand, and to “distract and relax”, on the other.

Esfuerzos nacionales para la implementación de las sentencias interamericanas: La experiencia mexicana

Directory of Open Access Journals (Sweden)

Gladys Fabiola Morales Ramírez

2015-08-01

Full Text Available El presente artículo está dedicado al análisis de la experiencia de México en el cumplimiento de sentencias emitidas por la Corte Interamericana de Derechos Humanos, específicamente los esfuerzos de las autoridades nacionales en el diseño de instrumentos especializados para la implementación de estas decisiones.

Susceptibility of 17-4PH stainless steel to stress corrosion cracking in aqueous environments by electrochemical techniques.; Estudio de la corrosion bajo tension del acero 17-4PH en medios acuosos usando tecnicas electroquimicas

Energy Technology Data Exchange (ETDEWEB)

Diaz S, A C [Instituto Nacional de Investigaciones Nucleares, Mexico City (Mexico)

1998-12-31

The susceptibility of a 17-4PH type steel to Stress Corrosion Cracking (SCC) in low pressure steam turbine environments was assessed using slow strain rate test at 90 Centigrade and at 1.35x10{sup -6} seg{sup -1}. Environments tested included different concentrated solutions of NaCl, NaOH and Na{sub 2}SO{sub 4}. It was concluded that this steel is susceptible to SCC in 20 % NaCl and pH=3 and in 20 % NaCl pH=neutral but under cathodic polarisation. The electrochemical potential noise of the specimen was monitored during the test. The naturally fluctuations in potential were arise due to spontaneous brake protective film and were characteristics of the kind of corrosion like pit or stress corrosion cracking. After that using Fast Fourier Transformer (FFT) the noise data set were analyzed to obtain power spectral density plots which showed differences between general corrosion and localized corrosion. Polarization curves were carry out at two different rates and them showed the general behavior of the systems. (Author).

Arte y marketing: Esfuerzos interdisciplinarios para una cultura de conciencia socio-ambiental

OpenAIRE

Belis Paulino, Elisaul

2014-01-01

Partiendo de referencias teóricas de Baudrillard, Kosuth, Debord, Kotler, Armstrong, Hagtvedt y Patrick se analiza la situación de la sociedad de consumo actual, así como iniciativas realizadas para generar conciencia ambiental. Se plantea la oportunidad de sumar esfuerzos de disciplinas como el Arte y el Marketing con la finalidad de traer propuestas que contribuyan a comunicar temas socio-ambientales. Viéndose casos de artistas como Colbert y Jordan, y campañas de ma...

Uso de la programación lineal paramétrica en la solución de un problema de planeación de requerimiento de materiales bajo condiciones de incertidumbre

Directory of Open Access Journals (Sweden)

Martin Darío Arango Serna

2010-09-01

Full Text Available El uso de la teoría de los conjuntos difusos como una metodología para el modelado y análisis de sistemas de decisión es de particular interés para investigadores en ingeniería industrial, debido a la capacidad para permitir un análisis cualitativo y cuantitativo de los problemas que implican vaguedad e imprecisión. Es así como, en un esfuerzo por obtener una mejor compresión del uso de la lógica difusa en la ingeniería industrial y más específicamente en el campo de la planificación de la producción, se proporciona en el presente artículo un problema de planeación de requerimiento de materiales (MRP bajo condiciones de incertidumbre aplicado a la industria automotriz, y el cual es solucionado a través de programación lineal paramétrica difusa.

DIFERENTES MODELOS DE REGRESIÓN PARA DESCRIBIR LA RELACIÓN V.O2-FC Y PARA ESTIMAR EL V.O2 A DIFERENTES INTENSIDADES DE ESFUERZO

Directory of Open Access Journals (Sweden)

Nuria Garatachea Vallejo

2005-01-01

Full Text Available Muchos son los estudios que demuestran el potencial de la frecuencia cardiaca (FC para estimar el coste energético de una actividad física, ya que se relaciona directamente con el consumo de oxígeno (V. O2. La mayoría de estudios describen la relación V. O2- FC como lineal para un amplio rango de esfuerzo, exceptuando los valores de reposo aunque se han propuesto diferentes funciones matemáticas continuas no lineales sin existir todavía un acuerdo en la ecuación más apropiada. También existen estudios que apuntan un cambio en la relación V. O2-FC en función de la intensidad del esfuerzo. Nuestro objetivo fue determinar cuál es la mejor función matemática que describe la relación entre la FC y el V. O2 y decidir cuál es la mejor función matemática para estimar el V. O2 a diferentes intensidades de esfuerzo. Participaron 14 sujetos que realizaron una prueba de esfuerzo máxima sobre cicloergómetro y una prueba que consistía en pedalear a 5 intensidades de esfuerzo (40, 50, 60, 70 y 80% del V. O2max durante 3 minutos. Durante ambas pruebas se midió V. O2 y frecuencia cardiaca. El modelo lineal y potencial fueron los modelos matemáticos más exactos para describir la relación V. O2-FC. El mayor error de estimación se produjo a bajas intensidades de esfuerzo. En conclusión, la elección de un tipo u otro de regresión influye en la exactitud del método de monitorización de la frecuencia cardiaca.

Corrosion and corrosion control

International Nuclear Information System (INIS)

Khanna, A.S.; Totlani, M.K.

1995-01-01

Corrosion has always been associated with structures, plants, installations and equipment exposed to aggressive environments. It effects economy, safety and product reliability. Monitoring of component corrosion has thus become an essential requirement for the plant health and safety. Protection methods such as appropriate coatings, cathodic protection and use of inhibitors have become essential design parameters. High temperature corrosion, especially hot corrosion, is still a difficult concept to accommodate in corrosion allowance; there is a lack of harmonized system of performance testing of materials at high temperatures. In order to discuss and deliberate on these aspects, National Association for Corrosion Engineers International organised a National Conference on Corrosion and its Control in Bombay during November 28-30, 1995. This volume contains papers presented at the symposium. Paper relevant to INIS is indexed separately. refs., figs., tabs

Corrosion of metallic materials. Dry corrosion, aqueous corrosion and corrosion by liquid metal, methods of protection

International Nuclear Information System (INIS)

Helie, Max

2015-01-01

This book is based on a course on materials given in an engineering school. The author first gives an overview of metallurgy issues: metallic materials (pure metals, metallic alloys), defects of crystal lattices (point defects, linear defects or dislocations), equilibrium diagrams, steels and cast, thermal processing of steels, stainless steels, aluminium and its alloys, copper and its alloys. The second part addresses the properties and characterization of surfaces and interfaces: singularity of a metal surface, surface energy of a metal, energy of grain boundaries, adsorption at a material surface, metal-electrolyte interface, surface oxide-electrolyte interface, techniques of surface analysis. The third chapter addresses the electrochemical aspects of corrosion: description of the corrosion phenomenon, free enthalpy of a compound and free enthalpy of a reaction, case of dry corrosion (thermodynamic aspect, Ellingham diagram, oxidation mechanisms, experimental study, macroscopic modelling), case of aqueous corrosion (electrochemical thermodynamics and kinetics, experimental determination of corrosion rate). The fourth part addresses the different forms of aqueous corrosion: generalized corrosion (atmospheric corrosion, mechanisms and tests), localized corrosion (galvanic, pitting, cracking, intergranular, erosion and cavitation), particular cases of stress cracking (stress corrosion, fatigue-corrosion, embrittlement by hydrogen), and bi-corrosion (of non alloyed steels, of stainless steels, and of aluminium and copper alloys). The sixth chapter addresses the struggle and the protection against aqueous corrosion: methods of prevention, scope of use of main alloys, geometry-based protection of pieces, use of corrosion inhibitors, use of organic or metallic coatings, electrochemical protection. The last chapter proposes an overview of corrosion types in industrial practices: in the automotive industry, in the oil industry, in the aircraft industry, and in the

DISEÑO DE UNA METODOLOGIA DE PERFECCIONAMIENTO Y ENRIQUECIMIENTO EN MATERMATICA PARA ALUMNOS Y PROFESORES BASADA EN LA ESTRUCTURA DEL RAZONAMIENTO LOGICO-MATEMATICO

OpenAIRE

PEREZ WILSON, CARLOS EDUARDO

2011-01-01

Los resultados deficitarios que evidencian en los últimos años los diferentes mecanismos de evaluación nacional e internacional en que participan los alumnos y profesores del sector escolar chileno en el área de la Matemática, muestran en forma sostenida un bajo nivel de logro, que no ha logrado mejoras sustantivas a pesar de los esfuerzos y recursos comprometidos, esfuerzos que al ser de conocimiento público, agudizan la percepción negativa social, que lo define casi como un “pro...

EFECTO DEL TIPO DE PROPULSION EN LA FRECUENCIA CARDIACA MAXIMA Y EN LA PERCEPCION DEL ESFUERZO EN CARRERA

Directory of Open Access Journals (Sweden)

Pietro Scaglioni Solano

2001-12-01

Full Text Available Este estudio examina el efecto del tipo de propulsión sobre la Frecuencia Cardíaca (FC y el Esfuerzo Percibido (EP, Escala de Borg en el ejercicio de carrera, obtenidas durante dos protocolos equivalentes, en terreno plano (pendiente 0%, uno con propulsión externa (motor, en la banda sinfín y otro con autopropulsión (carrera en pista de atletismo. 14 corredores (34.3 +/- 9.77 años, 1.74 +/- 0.06m, 75.3 +/- 10.3 Kg realizaron un protocolo que consistía en un calentamiento de 30 min. a una intensidad entre 60 y 70% de FCmáx. seguido de un incremento gradual de la intensidad del ejercicio, aumentando la velocidad de calentamiento 1.6 Km/h cada 30 seg., llevando al sujeto a un esfuerzo máximo en un lapso de 3 a 4 minutos, se recupera hasta la condición de calentamiento, se repite dos veces el proceso de incremento gradual y recuperación, escogiendo el valor máximo de FC y EP de los tres obtenidos. En el protocolo de pista, se marcó el paso al sujeto con una bicicleta provista de un velocímetro calibrado. Se realizaron mediciones de EP durante el calentamiento (EPC y de FC y EP durante los esfuerzos máximos (FCM, EPM. La FC del calentamiento se mantuvo constante para ambos protocolos (119.2 +/- 5.3 latidos/min; 65 +/- 2.4 % de FCmáx. Se compararon los datos obtenidos con propulsión externa, (EPC1, FCM1, EPM1 y los obtenidos con autopropulsión (EPC2, FCM2, EPM2 aplicando pruebas T. No se encontraron diferencias significativas para la FCmáx entre los dos protocolos (FCM1=181.8+/ 8.3 ; FCM2= 181.5+/- 6.9. Para EP se encontraron diferencias significativas (p< 0.01 entre los dos protocolos para el esfuerzo máximo (EPM1= 16.22+/-2.12 ; EPM2= 15.11+/- 2.09 y también para la fase de calentamiento (EPC1=10+/- 1 ; EPC2 = 8.56+/- 1.74. Los resultados indican que no hay un efecto del tipo de propulsión en la FC máx en carrera, por lo que se puede utilizar indistintamente una prueba en banda sinfín o en el campo para estimar un valor m

Factores asociados al bajo peso al nacer

Directory of Open Access Journals (Sweden)

Georgina J Peraza Roque

2001-10-01

Full Text Available El bajo peso al nacer (BPN ha constituido un enigma en la ciencia a través de los tiempos. Múltiples son las investigaciones realizadas acerca de las causas que lo producen y las consecuencias que provoca. Su importancia no solo radica en lo que significa en la morbilidad y la mortalidad infantil, sino que estos niños tienen habitualmente múltiples problemas posteriores. El Programa para la Reducción del BPN señala que los niños nacidos con un peso inferior a los 2 500 g presentan riesgo de mortalidad 14 veces mayor durante el primer año de vida, en comparación con los niños que nacen con un peso normal a término. Dentro de los factores de riesgo del BPN se han encontrado con mayor frecuencia en estudios realizados por diferentes autores, los siguientes: el embarazo en la adolescencia, la desnutrición en la madre, el hábito de fumar, la hipertensión arterial durante el embarazo, la sepsis cervicovaginal, la anemia y los embarazos gemelares, entre otros. Es innegable la influencia que el BPN tiene sobre las futuras generaciones, por lo que debe constituir la diana de los esfuerzos que el médico y la enfermera deben desarrollar en su prevención, sobre todo en la comunidadLow birth weight has been an enigma for Science through times. A lot of research works have been carried out about its causes and consequences. The importance of LBW not only lies in its meaning for infant mortality and morbidity but also in the many problems that low birth weight children regularly face in the future. The program for the reduction of LBW points out that newborns weighing under 2500g have during his/her first year of life a mortality risk 14 times higher than newborns with a normal weight at term. Among the low birth weight risk factors, a number of studies by various authors have frequently found the following; pregnancy at adolescence; undernourishment in mothers, smoking, blood hypertension during pregnancy, cervix-vaginal sepsis; anemia, twin

Contacto normal entre un medio elasto-plástico continuo y una esfera rígida : observaciones experimentales y computacionales

Directory of Open Access Journals (Sweden)

Ángela María Pedraza

2005-01-01

Full Text Available Se presenta en este trabajo una investigación experimental y numérica del contacto normal de una esfera rígida con una placa plana de material cuyo comportamiento mecánico se asume de tipo elasto-plástico. Los esfuerzos locales bajo el punto de contacto se han obtenido experimentalmente mediante visualización foto-elástica. Se ha evaluado numéricamente la evolución de los bulbos de esfuerzo bajo el punto contacto como función del tiempo y se ha efectuado la comparación con las observaciones experimentales. Los resultados indican que un modelo elasto-plástico tridimensional reproduce de manera apropiada las características principales observadas en los experimentos físicos. Este ejercicio puramente académico y de carácter didáctico enfatiza en el enorme potencial de los elementos finitos en la solución de problemas de deformación bajo diferentes tipos de modelos constitutivos y pone de manifiesto la enorme utilidad del modelamiento matemático y computacional basado en aproximaciones continuas de la materia

Methodology for the accelerated simulation of the deterioration that by atmospheric corrosion appears in electronic equipment; Metodologia para la simulacion acelerada del deterioro que por corrosion atmosferica se presenta en equipo electronico

Energy Technology Data Exchange (ETDEWEB)

Ortiz Prado, A.; Schouwenaars, R.; Cerrud Sanchez, S.M. [Facultad de Ingenieria, UNAM, Mexico, D.F. (Mexico)

2002-12-01

The corrosion resistance of systems and electronic parts which are designed to work in atmospheric conditions have been tested for decades; some of these methods were the Cyclic Humidity Test, Field Tests and Salt Spray (Fog) Testing, the latter was one of the most popular methods. However, the salt spray test and most of the other existing methods do not show strong relationships with the real conditions of service. For this reason, it is necessary to develop appropriated methods and equipment for the accelerated simulation of real atmospheric corrosion phenomena. This article seeks to demonstrate the need to develop a test and the necessary equipment to reproduce the damage in electronic systems and equipment by atmospheric corrosion. [Spanish] Para la evaluacion de la resistencia a la corrosion de sistemas y equipo electronico que trabajaran bajo condiciones de deterioro generadas por el medio ambiente, se han aplicado una serie de ensayos, donde el mas popular es el de camara de niebla salina. Sin embargo, este y otros que se han elaborado para tal efecto no tienen ninguna relacion con las condiciones reales de servicio, por lo que es necesario un metodo de evaluacion que permita simular de forma acelerada los fenomenos de deterioro por efectos ambientales. Este articulo pretende demostrar la necesidad de desarrollar una prueba, que en forma acelerada, reproduzca el dano que sufre el material por efecto de la atmosfera; el cual se orienta a la evaluacion de equipo electrico y electronico.

Factores de riesgo en el bajo peso al nacer

Directory of Open Access Journals (Sweden)

Guillermo Díaz Alonso

Full Text Available Se realizó un estudio retrospectivo de tipo caso control en el área del Policlínico Docente "Luis A. Turcios Lima" del municipio 10 de Octubre durante el período de 1990 a 1993, con el objetivo de identificar el comportamiento del bajo peso al nacer, establecer la existencia y la intensidad de esta entidad con los factores de riesgo seleccionados, e identificar el grado de influencia individual de dichos factores. La muestra quedó conformada por 92 recién nacidos de bajo peso y 468 con normopeso. Las variables estudiadas fueron la edad materna, la valoración ponderal, las complicaciones obstétricas, las enfermedades asociadas con la gestación, el hábito de fumar y el período intergenésico. Se aplicó el test chi-cuadrado, el odds- -ratio y el de riesgo atribuible en los nacimientos expuestos y en la población total. Todas las variables estuvieron asociadas significativamente con el bajo peso al nacer, y fueron identificadas como factores de riesgo con influencia marcada: la edad materna de 35 años o más, la amenaza de parto prematuro, la rotura prematura de membranas, la toxemia y la diabetes mellitus; con efecto moderado, el bajo peso materno, un período intergenésico menor de 1 año, la hipertensión arterial, el asma bronquial, el hábito de fumar, la sepsis urinaria, y con influencia ligera, la edad materna inferior a los 20 años.

Análisis de esfuerzos en túneles excavados en materiales con K0 diferente a 1.0

Directory of Open Access Journals (Sweden)

Ricardo E. Barbosa Carrillo

1984-09-01

Full Text Available En el presente trabajo se desarrollaron las soluciones elásticas para túneles circulares revestidos, excavados en materiales con un estado inicial de esfuerzos σxo=Kσyo se formularon los modelos para resolver el problema utilizando la técnica de los elementos finitos.

Propagation of cracks by stress corrosion in conditions of BWR type reactor; Propagacion de grietas por corrosion bajo esfuerzo en condiciones de reactor de agua en ebullicion (BWR)

Energy Technology Data Exchange (ETDEWEB)

Merino C, F.J. [ININ, 52045 Estado de Mexico (Mexico); Fuentes C, P. [ITT, Metepec, Estado de Mexico (Mexico)]. E-mail: fjmc@nuclear.inin.mx

2004-07-01

In this work, the obtained results when applying the Hydrogen Chemistry to a test tube type Compact Tension (CT), built in austenitic stainless steel 304l, simulating the conditions to those that it operates a Boiling Water Reactor (BWR), temperature 288 C and pressure of 8 MPa are presented. With the application of this water chemistry, seeks to be proven the diminution of the crack propagation speed. (Author)

Actualización en el manejo del colesterol hdl bajo

Directory of Open Access Journals (Sweden)

Rigotti R. Attilio, Dr.

2012-11-01

Full Text Available Los niveles plasmáticos bajos de colesterol transportado en las lipoproteínas de alta densidad (HDL constituyen un elemento independiente de riesgo cardiovascular ateroesclerótico. Algunos protocolos clínicos enfocados en el manejo farmacológico de los niveles bajos de colesterol HDL en pacientes de alto riesgo cardiovascular han mostrado resultados favorables. Por otro lado, existen nuevas formulaciones de la niacina, el agente farmacológico disponible más efectivo para el manejo del colesterol HDL bajo, y se están desarrollando nuevos fármacos más potentes para aumentar los niveles plasmáticos de colesterol HDL. En el futuro, nuevos medicamentos que modulen el metabolismo de HDL y demuestren beneficio sobre el control del riesgo cardiovascular ateroesclerótico, podrían mejorar aún más el manejo actual de esta condición patológica que se basa esencialmente en el uso de estatinas.

EVALUACION DE LA RESISTENCIA A LA CORROSION DEL SISTEMA PRIMER EPOXICO RICO EN ZINC/ACABADO POLISILOXANO POR MEDIO DE ESPECTROSCOPIA DE IMPEDANCIA ELECTROQUIMICA

Directory of Open Access Journals (Sweden)

ANDRES ALBERTO GUZMAN ROSAS

2011-01-01

Full Text Available En este trabajo fue estudiado el sistema primer epoxico rico en zinc / acabado polisiloxano aplicado sobre laminas de acero al carbono laminado en caliente y sometido a camaras de corrosion acelerada (inmersion total, niebla salina, ciclo de corrosion y prohesion por un periodo de hasta 5000 horas. Las probetas bajo estudio se evaluaron cada 20 dias por medio de espectroscopia de impedancia electroquimica y al final de la prueba se realizaron chequeos visuales y microscopia optica para ver la morfologia de la interface metal-recubrimiento y microespectroscopia Raman para identificar la presencia de posibles productos de corrosion. Los resultados de impedancia fueron simulados por medio de circuitos electricos equivalentes. Para el sistema se encontraron modulos de impedancia del orden de 1011 ¿.cm2 en prohesion, 1010 ¿.cm2 en ciclo de corrosion, 109 ¿.cm2 tanto niebla salina como en las inmersiones totales (NaCl 10-2M y Na2SO4 10-2M. Este sistema tuvo durante el tiempo de pruebas un comportamiento excelente con altas resistencias de pelicula y de transferencia de carga y bajas capacitancias de pelicula y de doble capa.

El crecimiento y desarrollo ante la prematuridad y el bajo peso al nacer

Directory of Open Access Journals (Sweden)

Christine Baccarat de Godoy Martins

2015-09-01

Full Text Available Objetivo: Realizar una revisión bibliográfica sobre el crecimiento y desarrollo de prematuros y/o de bajo peso al nacer. Metodología: Se utilizaron las bases de datos lilacs, medline y scielo. Se encontraron 64 trabajos: 10 publicados en 2005, 10 en 2006, 12 en 2007, 16 en 2008, 8 en 2009 y 8 en 2010. Las publicaciones halladas pertenecían a las áreas de medicina (59,4%, nutrición (7,8%, enfermería (7,8%, salud pública (7,8%, psicología (6,2%, epidemiología (4,7%, fisiología (3,1% y fonoaudiología (3,1%. Resultados:Los textos encontrados permitieron la organización del conocimiento producido según las siguientes categorías de análisis: Factores asociados al bajo peso en el nacimiento/prematuridad; Repercusiones del bajo peso en el nacimiento/prematuridad para el crecimiento y desarrollo y medidas de prevención; y Supervivencia de los recién nacidos prematuros o de bajo peso. Conclusión: Los niños nacidos prematuramente y de bajo peso generalmente presentan déficit de desarrollo. Un acompañamiento postnatal centrado en el crecimiento y desarrollo es fundamental.

El Esfuerzo Físico en el Baile Flamenco de Principios del S. XX y el Actual

Directory of Open Access Journals (Sweden)

Alfonso Vargas Macías

2008-06-01

Full Text Available En este artículo se analiza como ha evolucionado el esfuerzo físico del baile flamenco a lo largo del último siglo. Se ha estudiado el tiempo que se dedica a las fases de braceo y zapateado, así como los tipos, velocidad y frecuencia de zapa- teado. En todas las variables analizadas, se ha observado mayores exigencias en el baile fla- menco actual.

Estudio de corrosión bajo tensión en los aceros inoxidables 17-4PH y 17-7PH en presencia de NaCl y NaOH (20 % a 90 °C

Directory of Open Access Journals (Sweden)

Gaona-Tiburcio, Citlalli

2000-04-01

Full Text Available One of the problems that affects to the electric industry is the not programmed stoppages in the power plants, due to the failure of any main component: boiler, turbine and generator. In the turbine, the combined action of a corrosive agent (humid polluted vapor and a mechanical effort generally will result in Stress Corrosion Cracking (SCC. In this work the SCC susceptibility of the precipitation hardening stainless steels 17-4PH and 17- 7PH, thoroughly used in steam turbine blades of power stations is analyzed. The specimens were tested in the presence of NaCl and NaOH (20 % to 90 °C and different pH. The CERT test (Constant Extension Rate Test was used, at 10^-6 s^-1 supplementing it with electrochemical noise; the aim was to identify the conditions of maximum susceptibility and the performance of the studied materials. The fractographic analysis revealed ductile and brittle fracture. Intergranular crackings, characteristic of the anodic dissolution mechanism of the material was observed. Nevertheless, the main mechanism responsible the failure was hydrogen embrittlement.

Uno de los problemas que afecta a la industria eléctrica es el de los paros no programados en las plantas generadoras de electricidad, debidos al fallo de algún componente principal: caldera, turbina y generador. En la turbina, la acción combinada de un agente corrosivo (vapor húmedo contaminado y un esfuerzo mecánico, generalmente provocará corrosión bajo tensión (CBT. En este trabajo se analiza la susceptibilidad a la CBT de los aceros inoxidables, endurecibles por precipitación, 17-4PH y 17-7PH, ampliamente usados en alabes de turbina de vapor de centrales termoeléctricas. Las muestras se ensayaron en presencia de NaCl y NaOH (20 % a 90 °C, y distintos valores de pH. Se empleó el ensayo CERT (Constant Extensión Rate Test, a velocidades de 10^-6 s^-1, complementándolo con ruido electroquímico, buscando

Estudio de las propiedades mecánicas del sistema óseo (segunda parte)

OpenAIRE

Mendoza, Alvaro

2011-01-01

Los estudios se hicieron bajo la supervisión del área de Biomecánica. Los ensayos dieron a conocer los valores reales de los esfuerzos mecánicos que es capaz de resistir el tejido óseo. Se elaboraron curvas de esfuerzo-deformación, con la ayuda de deformímetros mecánicos y rosetas de deformación, encontrándose las diferentes propiedades mecánicas y dando una base sólida para estudios posteriores en el área, que ayuden aún más al desarrollo de la bioingeniería en Colombia.

Aulas-laboratorios de bajo costo, usando TIC

Directory of Open Access Journals (Sweden)

Silvia E. Calderón

2015-01-01

Full Text Available En este trabajo se presentan los resultados de una propuesta educativa orientada a promover el desarrollo de un pensamiento critico y un mayor interes por las ciencias experimentales. Con este fin desarrollamos propuestas de proyectos educativos susceptibles de ser destinadas a las aulas y laboratorios de las escuelas secundarias y primeros anos de la universidad, que resaltan los aspectos metodologicos de las ciencias. Aqui, realizamos una compilacion de varios proyectos, que ilustran formas de incorporar las tecnologias de la informacion y la comunicacion (TIC en diversos experimentos de ciencias, muchos de ellos publicados individualmente anteriormente, y que en conjunto se pueden utilizar para implementar un aula-laboratorio de bajo costo. Con TIC hacemos referencia a la convergencia de computadoras, sistemas audiovisuales, Internet, telefonia, y diversos equipos que se integran con algunos de ellos. Los proyectos intentan integrar areas como fisica, matematica, quimica, informatica, arte, etc. y apuntan a que los estudiantes puedan responder a las preguntas: .Como sabemos esto?, .Por que creemos en aquello? Preguntas que ilustran la naturaleza del pensamiento cientifico. Nuestra contribucion mas significativa es haber desarrollado ≪aulas-laboratorios≫ de muy bajo costo, usando TIC. Con el advenimiento de programas como ≪Una Laptop por Nino≫ que se estan implementando en varios paises de Latinoamerica, resulta oportuno utilizar este recurso como base para generar laboratorios de bajo costo, que creemos pueden ser una herramienta util para mejorar el aprendizaje de las ciencias, incentivar vocaciones y contribuir a desarrollar un pensamiento critico, a la par de desarrollar habilidades con el uso de las TIC que pueden ser de utilidad en diversos ambitos academicos y laborales.

Sesgo de género en el esfuerzo terapéutico Gender bias in treatment

Directory of Open Access Journals (Sweden)

María T. Ruiz-Cantero

2004-05-01

Full Text Available Los estudios de sesgo de género y el paradigma de la medicina basada en la evidencia comparten la hipótesis de que existen imprecisiones empíricas en la práctica médica. No obstante, falta información sobre la variabilidad de la práctica en función del sexo, y el androcentrismo puede ser una de sus causas. Muchos estudios biomédicos como los ensayos clínicos han utilizado a los hombres como prototipos poblacionales e inferido los resultados en las mujeres. Esta tendencia parte de la presunción errónea de igualdad entre mujeres y hombres. Las investigaciones sobre sesgo de género en el esfuerzo terapéutico se centran en el acceso a los hospitales de ambos sexos para igual necesidad, la comparación de los tiempos de demora y de espera desde los primeros síntomas hasta la atención sanitaria, los tipos de estrategias terapéuticas y el consumo y el gasto de medicamentos por sexo. También se incluyen investigaciones de sobreprescripción de terapias en los problemas de salud más prevalentes o exclusivos de mujeres. El sesgo de género en el esfuerzo terapéutico depende del sesgo de género en el esfuerzo diagnóstico; pues, la probabilidad de que quien padece sea tratado es casi nula si por cualquier causa queda excluido del proceso diagnóstico, o disminuye si en el proceso diagnóstico no se realizan las pruebas oportunas. Este artículo tiene como objetivo presentar una aproximación a la evidencia de sesgo de género en el esfuerzo terapéutico en España.Both gender bias studies and evidence-based medicine share the hypothesis of the existence of empirical uncertainty in medical practice. Nevertheless there is a lack of information regarding variations and sex, possibly due to androcentric reasons. Many biomedical studies ncluding randomised controlled trials, have used men as the population's prototype and applied its conclusions to women. This approach is based in an erroneous assumption of equality between men and women

CULTIVOS BAJO CUBIERTA EN EL SURESTE DE ESPAÑA

Directory of Open Access Journals (Sweden)

Encarnación Gil Meseguer

2011-01-01

Full Text Available En España, más de 62.000 ha regadas se cultivan en ambiente controlado, bajo determinadas cubiertas. Dos tercios se localizan en Andalucía, y más de la cuarta parte, en el Sureste de la Península Ibérica. En el espacio surestino, delimitado por la coincidencia de las isolíneas climáticas (isoyeta de los 400 mm anuales e isoterma de 16ºC de TMA y la línea de costa mediterránea entre Almería y Alicante, sobresalen una serie de estructuras con cubiertas de plásticos y mallas para la producción de cultivos intensivos en las comarcas del Levante Almeriense-Bajo Almanzora, Lorca y Valle Guadalentín, Campo de Cartagena-Mar Menor, Meridional de Alicante-Vega Baja, etc. Los avances tecnológicos aplicados al riego y al ciclo natural de la planta, se incorporan al cultivo forzado bajo cubierta, logrando modificar el ciclo de cultivo, con una amplitud en los calendarios para presentar el producto en los momentos de mayor demanda. El interés de esta agricultura intensiva de invernaderos, mallas y acolchados radica en su mayor productividad, empleo y precio final del producto.

Corrosion

Science.gov (United States)

Slabaugh, W. H.

1974-01-01

Presents some materials for use in demonstration and experimentation of corrosion processes, including corrosion stimulation and inhibition. Indicates that basic concepts of electrochemistry, crystal structure, and kinetics can be extended to practical chemistry through corrosion explanation. (CC)

Evaluacion del factor central y periferico en fatiga muscular

Directory of Open Access Journals (Sweden)

Marcela E. Panizza

1983-09-01

Full Text Available Se estúdio la fatiga muscular en 13 sujetos normales; para ello, fueron sometidos a un esfuerzo sostenido durante 10 minutos previo y posterior, al cual se realizo la medición de la onda M máxima. Durante el esfuerzo y cada 2 minutos, se obtuvieron cuantificaciones de la frecuencia y duración de las ondas positivas y negativas del EMG. Los resultados, mostraron diferencias significativas de estos valores, en función del tiempo de esfuerzo realizado, mientras que las mediciones de la onda M máxima inicial y final, no fueron diferentes, todo lo cual lleva a jerarquizar el factor central como el más importante en el desarrollo de fatiga, bajo nuestras condiciones de estudio, que son además de sencilla aplicación clínica.

Corrosion in airframes

OpenAIRE

PETROVIC ZORAN C.

2016-01-01

The introductory chapter provides a brief reference to the issue of corrosion and corrosion damage to aircraft structures. Depending on the nature and dimensions of this non uniformity, three different categories of corrosion are defined: uniform, selective and localized corrosion. The following chapters present the forms of corrosion that can occur in three defined categories of corrosion. Conditions that cause certain types of corrosion in various corrosive environments are discussed. Examp...

Corrosion engineering

Energy Technology Data Exchange (ETDEWEB)

Fontana, M.G.

1986-01-01

This book emphasizes the engineering approach to handling corrosion. It presents corrosion data by corrosives or environments rather than by materials. It discusses the corrosion engineering of noble metals, ''exotic'' metals, non-metallics, coatings, mechanical properties, and corrosion testing, as well as modern concepts. New sections have been added on fracture mechanics, laser alloying, nuclear waste isolation, solar energy, geothermal energy, and the Statue of Liberty. Special isocorrosion charts, developed by the author, are introduced as a quick way to look at candidates for a particular corrosive.

Bajo rendimiento escolar: una perspectiva desde el desarrollo del sistema nervioso

Directory of Open Access Journals (Sweden)

K. Shapiro Bruce, MD.

2011-03-01

Full Text Available El bajo rendimiento escolar es un problema frecuente y tiene múltiples causas; las alteraciones que lo caracterizan, se expresan fundamentalmente en las áreas de funcionamiento cognitivo, académico y conductual. El bajo rendimiento escolar es una vía final común de diferentes trastornos, etiologías y mecanismos. Es habitual la presencia de múltiples alteraciones, porque la disfunción cerebral en la niñez generalmente afecta a muchas funciones. Consecuente con lo anterior, los programas de manejo deben ser individualizados, comprensivos e incorporar aspectos del niño en particular, la escuela y la familia. La planificación del tratamiento incluye, educación y entrenamiento de los padres, adecuaciones académicas, técnicas para mantener la autoestima y un enfoque psicofarmacológico. Es necesario monitorear en forma continua los programas de manejo especialmente para detectar comorbilidades importantes que puedan emerger, para realizar modificaciones que se adecuen a los cambios en las demandas académicas y sociales a las diferentes edades del niño y para proveer de información actualizada. Las consecuencias que tenga el bajo rendimiento escolar para el niño dependerán en medida importante de las alteraciones subyacentes. El personal de salud tiene múltiples roles en la prevención, detección, diagnóstico y manejo del niño con bajo rendimiento escolar.

Estratificación del bajo peso al nacer desde un enfoque de determinantes sociales

Directory of Open Access Journals (Sweden)

Hilda María Delgado Acosta

2013-03-01

Full Text Available Fundamento: el área materno-infantil requiere de un enfoque en sus determinantes para aumentar el alcance estratégico de sus programas. Objetivo: estratificar el bajo peso al nacer en el municipio de Cienfuegos y caracterizar el bajo peso de acuerdo a determinantes sociales seleccionadas. Métodos: se realizó un estudio epidemiológico, descriptivo, correlacional sobre la estratificación del bajo peso al nacer en los consejos populares del municipio Cienfuegos, en el período comprendido entre los años 2003 y 2007. Los estratos se definieron según el valor de la media del índice de bajo peso al nacer en este periodo. Para realizar el análisis de las variables cualitativas en muestras independientes se utilizó la prueba de independencia u homogeneidad utilizada en el caso de dos muestras con resultado dicotómico o más. El procesamiento estadístico se realizó en el programa SPSS versión 15,0 y se utilizaron como medidas matemáticas para las variables cualitativas el porcentaje, y para las variables cuantitativas la media aritmética. La técnica estadística para relacionar las variables fue la prueba Chi-cuadrado. Resultados: se mostraron diferencias estadísticamente significativas entre los estratos de bajo, mediano y alto riesgo, en el nivel de escolaridad, estado civil, ocupación, evaluación nutricional, hábito de fumar, antecedentes de bajo peso al nacer, período ínter genésico. La única enfermedad asociada que mostró diferencias entre ellos fue la hipertensión gestacional. Conclusiones: el bajo peso al nacer continúa siendo un serio problema de salud en el municipio Cienfuegos, cuestión esta que debe ser abordada desde sus determinantes para realizar intervenciones futuras y el logro de mejores resultados.

Achievments of corrosion science and corrosion protection technology

International Nuclear Information System (INIS)

Fontana, M.; Stehjl, R.

1985-01-01

Problems of corrosion-mechanical strength of metals, effect of corrosive media on creep characteristics are presented. New concepts of the mechanism of corrosion cracking and its relation to hydrogen embrittlement are described. Kinetics and mechanism of hydrogen embrittlement effect on the process of corrosion cracking of different steels and alloys are considered. The dependence of such types of failure on various structural factors is shown. Data on corrosion cracking of high-strength aluminium and titanium alloys, mechanism of the processes and protective methods are given

Erosion–corrosion and corrosion properties of DLC coated low temperature Erosion–corrosion and corrosion properties of DLC coated low temperature

DEFF Research Database (Denmark)

Jellesen, Morten Stendahl; Christiansen, Thomas; Hilbert, Lisbeth Rischel

2009-01-01

of AISI 316 as substrate for DLC coatings are investigated. Corrosion and erosion–corrosion measurements were carried out on low temperature nitrided stainless steel AISI 316 and on low temperature nitrided stainless steel AISI 316 with a top layer of DLC. The combination of DLC and low temperature...... nitriding dramatically reduces the amount of erosion–corrosion of stainless steel under impingement of particles in a corrosive medium....

Corrosion Evaluation and Corrosion Control of Steam Generators

International Nuclear Information System (INIS)

Maeng, W. Y.; Kim, U. C.; Sung, K. W.; Na, J. W.; Lee, Y. H.; Lee, D. H.; Kim, K. M.

2008-06-01

Corrosion damage significantly influences the integrity and efficiency of steam generator. Corrosion problems of steam generator are unsolved issues until now even though much effort is made around world. Especially the stress corrosion cracking of heat exchange materials is the first issue to be solved. The corrosion protection method of steam generator is important and urgent for the guarantee of nuclear plant's integrity. The objectives of this study are 1) to evaluate the corrosion properties of steam generator materials, 2) to optimize the water chemistry of steam generator and 3) to develop the corrosion protection method of primary and secondary sides of steam generator. The results will be reflected to the water chemistry guideline for improving the integrity and efficiency of steam generator in domestic power plants

Estudio de las propiedades mecánicas del sistema óseo (Segunda parte

Directory of Open Access Journals (Sweden)

Alvaro Mendoza

1998-09-01

Full Text Available Los estudios se hicieron bajo la supervisión del área de Biomecánica. Los ensayos dieron a conocer los valores reales de los esfuerzos mecánicos que es capaz de resistir el tejido óseo. Se elaboraron curvas de esfuerzo-deformación, con la ayuda de deformímetros mecánicos y rosetas de deformación, encontrándose las diferentes propiedades mecánicas y dando una base sólida para estudios posteriores en el área, que ayuden aún más al desarrollo de la bioingeniería en Colombia.

Modelo dinámico para la estimación temprana de esfuerzo en proyectos de desarrollo de software

Directory of Open Access Journals (Sweden)

Ana Lucía Pérez

2006-07-01

Full Text Available Existen modelos para estimación del esfuerzo requerido en proyectos software que presentan limitaciones cuando se utilizan en etapas tempranas del ciclo de vida de desarrollo. En este artículo se presenta una revisión de los modelos existentes y se describe un nuevo modelo capaz de estimar esfuerzo en las primeras etapas del desarrollo, cuyas entradas dependen de históricos de proyectos realizados y de la experiencia de proyectos similares. El modelo expuesto en este artículo fue resultado de un proyecto de investigación aplicada realizado entre la Universidad de Antioquia y Orbitel S. A., con el objetivo de estimar el esfuerzo requerido por los analistas de la Gerencia de Informática para la creación y operación de soluciones. Considerando los históricos disponibles en Orbitel, nuestro modelo entrega estimaciones precisas desde el punto de vista estadístico. Adicionalmente, el modelo propuesto puede ser simulado con una herramienta orientada a la Web.There are models for estimation of the effort required in software projects that present limitations when they are used in early stages of the service life of development. In this article a revision of the existing models is presented and a new model able of estimating effort in the first stages of the development is described, whose entrances depend on both historical of projects made and on the experience of similar projects. The model exposed in this article was the result of an applied research project done between Universidad de Antioquia and Orbitel S.A., with the objective of considering the effort required by the analysts of the Management of Computer science for the creation and operation of solutions. Considering the historical available in Orbitel, our model gives precise estimations from the statistical point of view. Additionally, the proposed model can be simulated with a tool oriented to the Web.

Corrosion-Activated Micro-Containers for Environmentally Friendly Corrosion Protective Coatings

Science.gov (United States)

Li, Wenyan; Buhrow, J. W.; Zhang, X.; Johnsey, M. N.; Pearman, B. P.; Jolley, S. T.; Calle, L. M.

2016-01-01

This work concerns the development of environmentally friendly encapsulation technology, specifically designed to incorporate corrosion indicators, inhibitors, and self-healing agents into a coating, in such a way that the delivery of the indicators and inhibitors is triggered by the corrosion process, and the delivery of self-healing agents is triggered by mechanical damage to the coating. Encapsulation of the active corrosion control ingredients allows the incorporation of desired autonomous corrosion control functions such as: early corrosion detection, hidden corrosion detection, corrosion inhibition, and self-healing of mechanical damage into a coating. The technology offers the versatility needed to include one or several corrosion control functions into the same coating.The development of the encapsulation technology has progressed from the initial proof-of-concept work, in which a corrosion indicator was encapsulated into an oil-core (hydrophobic) microcapsule and shown to be delivered autonomously, under simulated corrosion conditions, to a sophisticated portfolio of micro carriers (organic, inorganic, and hybrid) that can be used to deliver a wide range of active corrosion ingredients at a rate that can be adjusted to offer immediate as well as long-term corrosion control. The micro carriers have been incorporated into different coating formulas to test and optimize the autonomous corrosion detection, inhibition, and self-healing functions of the coatings. This paper provides an overview of progress made to date and highlights recent technical developments, such as improved corrosion detection sensitivity, inhibitor test results in various types of coatings, and highly effective self-healing coatings based on green chemistry. The NASA Kennedy Space Centers Corrosion Technology Lab at the Kennedy Space Center in Florida, U.S.A. has been developing multifunctional smart coatings based on the microencapsulation of environmentally friendly corrosion

Review on stress corrosion and corrosion fatigue failure of centrifugal compressor impeller

Science.gov (United States)

Sun, Jiao; Chen, Songying; Qu, Yanpeng; Li, Jianfeng

2015-03-01

Corrosion failure, especially stress corrosion cracking and corrosion fatigue, is the main cause of centrifugal compressor impeller failure. And it is concealed and destructive. This paper summarizes the main theories of stress corrosion cracking and corrosion fatigue and its latest developments, and it also points out that existing stress corrosion cracking theories can be reduced to the anodic dissolution (AD), the hydrogen-induced cracking (HIC), and the combined AD and HIC mechanisms. The corrosion behavior and the mechanism of corrosion fatigue in the crack propagation stage are similar to stress corrosion cracking. The effects of stress ratio, loading frequency, and corrosive medium on the corrosion fatigue crack propagation rate are analyzed and summarized. The corrosion behavior and the mechanism of stress corrosion cracking and corrosion fatigue in corrosive environments, which contain sulfide, chlorides, and carbonate, are analyzed. The working environments of the centrifugal compressor impeller show the behavior and the mechanism of stress corrosion cracking and corrosion fatigue in different corrosive environments. The current research methods for centrifugal compressor impeller corrosion failure are analyzed. Physical analysis, numerical simulation, and the fluid-structure interaction method play an increasingly important role in the research on impeller deformation and stress distribution caused by the joint action of aerodynamic load and centrifugal load.

Corrosion Evaluation and Corrosion Control of Steam Generators

Energy Technology Data Exchange (ETDEWEB)

Maeng, W. Y.; Kim, U. C.; Sung, K. W.; Na, J. W.; Lee, Y. H.; Lee, D. H.; Kim, K. M

2008-06-15

Corrosion damage significantly influences the integrity and efficiency of steam generator. Corrosion problems of steam generator are unsolved issues until now even though much effort is made around world. Especially the stress corrosion cracking of heat exchange materials is the first issue to be solved. The corrosion protection method of steam generator is important and urgent for the guarantee of nuclear plant's integrity. The objectives of this study are 1) to evaluate the corrosion properties of steam generator materials, 2) to optimize the water chemistry of steam generator and 3) to develop the corrosion protection method of primary and secondary sides of steam generator. The results will be reflected to the water chemistry guideline for improving the integrity and efficiency of steam generator in domestic power plants.

Bajo Peso al Nacer. Factores de riesgo y calidad de la atención Prenatal. Buenaventura. 2008-2009

Directory of Open Access Journals (Sweden)

Luis Enrique Gallardo-Ibarra

2012-01-01

Full Text Available Se realizó estudio descriptivo sobre Bajo Peso al Nacer, Área de Salud Buenaventura, bienio 2008-2009, sobre factores de riesgo y calidad de la atención médica recibida por las gestantes que aportaron recién nacidos bajo peso. Los datos estadísticos se obtuvieron mediante revisión de historias clínicas familiares, obstétricas y hospitalarias. Se emplearon métodos estadísticos histórico lógico, análisis y síntesis e inducción-deducción. Se obtuvo predominio del CIUR como variedad de Bajo Peso al Nacer, mostraron asociación con el bajo peso al nacer la valoración nutricional Bajo Peso materna al inicio de la gestación, insuficiente ganancia de peso, ingreso percápita bajo, malas condiciones de vivienda, antecedentes de dos o más abortos, multigestación, período intergenésico corto, HTA y sepsis cervicovaginal. La Atención Prenatal fue deficiente. No existió relación entre grupos de edades menores de 20 o mayor de 35 años y hábitos tóxicos con la aparición del bajo peso al nacer.

Corrosion cracking

International Nuclear Information System (INIS)

Goel, V.S.

1985-01-01

This book presents the papers given at a conference on alloy corrosion cracking. Topics considered at the conference included the effect of niobium addition on intergranular stress corrosion cracking, corrosion-fatigue cracking in fossil-fueled-boilers, fracture toughness, fracture modes, hydrogen-induced thresholds, electrochemical and hydrogen permeation studies, the effect of seawater on fatigue crack propagation of wells for offshore structures, the corrosion fatigue of carbon steels in seawater, and stress corrosion cracking and the mechanical strength of alloy 600

Pipeline corrosion prevention by pH stabilization or corrosion inhibitors

Energy Technology Data Exchange (ETDEWEB)

Nyborg, Rolf [Institute for Energy Technology, Oslo (Norway)

2009-07-01

In many offshore oil and gas projects the pipeline costs are a considerable part of the investment and can become prohibitively high if the corrosivity of the fluid necessitates the use of corrosion resistant alloys instead of carbon steel. Development of more robust and reliable methods for internal corrosion control can increase the application range of carbon steel and therefore have a large economic impact. Corrosion control of carbon steel pipelines has traditionally often been managed by the use of corrosion inhibitors. The pH stabilization technique has been successfully used for corrosion control of several large wet gas pipelines in the last years. This method has advantages over film forming corrosion inhibitors when no or little formation water is produced. The use of corrosion inhibitors in multiphase pipelines implies several challenges which are not fully accounted for in traditional corrosion inhibitor testing procedures. Specialized test procedures have been developed to take account for the presence of emulsions dispersions and sand and clay particles in corrosion inhibitor testing. (author)

Underground pipeline corrosion

CERN Document Server

Orazem, Mark

2014-01-01

Underground pipelines transporting liquid petroleum products and natural gas are critical components of civil infrastructure, making corrosion prevention an essential part of asset-protection strategy. Underground Pipeline Corrosion provides a basic understanding of the problems associated with corrosion detection and mitigation, and of the state of the art in corrosion prevention. The topics covered in part one include: basic principles for corrosion in underground pipelines, AC-induced corrosion of underground pipelines, significance of corrosion in onshore oil and gas pipelines, n

Social Change of Bajo Tribe Society in Karimunjawa: From "Sea Tribe" to "Land Tribe"

Directory of Open Access Journals (Sweden)

Titiek Suliyati

2017-12-01

The result of the research shows that there is a social change in Bajo society living permanently in Karimunjawa that is, the change of daily behavior in the society, social interaction with other tribes, values held by the society and social institution, structure and social classes. Social change occurring to Bajo society in Karimunjawa brings positive influences. The social changes among others are awareness towards the importance of education, Bajo society has new jobs other than fisherman, the increase of income, living standard, also modernization in fisheries system. The negative impact as a consequence of the social changes is faded culture, changes in life orientation and views of life, and consumerism in the society.

Secuelas del neurodesarrollo de recién nacidos prematuros de extremadamente bajo peso y de muy bajo peso a los dos años de edad, egresados de la Unidad de Cuidados Intensivos Neonatales del Hospital Nacional Edgardo Rebagliati Martins 2009-2014

OpenAIRE

Fernández Sierra, Carmen; Matzumura Kasano, Juan; Gutiérrez Crespo, Hugo; Zamudio Eslava, Luisa; Melgarejo García, Giannina

2017-01-01

Objetivo: Describir las secuelas del neurodesarrollo de los recién nacidos prematuros de extremadamente bajo peso y de muy bajo peso a los dos años de edad, egresados de la Unidad de Cuidados Intensivos Neonatales del Hospital Nacional Edgardo Rebagliati Martins. Materiales y métodos: Estudio descriptivo, retrospectivo, transversal en una población de 190 prematuros de extremadamente bajo peso y de muy bajo peso que nacieron durante enero 2009 a junio del 2014, egresados de la Unidad de Cuida...

Monitoring corrosion rates and localised corrosion in low conductivity water

DEFF Research Database (Denmark)

Hilbert, Lisbeth Rischel

2006-01-01

Monitoring of low corrosion rates and localised corrosion in a media with low conductivity is a challenge. In municipal district heating, quality control may be improved by implementing on-line corrosion monitoring if a suitable technique can be identified to measure both uniform and localised...... corrosion. Electrochemical techniques (LPR, EIS, crevice corrosion current) as well as direct measurement techniques (high-sensitive electrical resistance, weight loss) have been applied in operating plants. Changes in the corrosion processes are best monitored in non-aggressive, low conductivity media...

Atmospheric corrosion of low carbon steel in a polar marine environment. Study of the effect of wind regime; Corrosion atmosferica del acero bajo en carbono en un ambiente marino polar. Estudio del efecto del regimen de vientos

Energy Technology Data Exchange (ETDEWEB)

Rivero, S.; Chico, B.; Fuente, D. de la; Morcillo, M.

2007-07-01

The present work studies the atmospheric corrosion of carbon steel (UNE-EN 10130) in a sub-polar marine environment (Artigas Antarctic Scientific Base (BCAA), Uruguay) as a function of site atmospheric salinity and exposure time. A linear relationship is established between corrosion rate and airborne salinity deposition rate, valid in the deposition range encountered (125-225 mg Cl-l/m{sup 2}.d) and a bi logarithmic relationship established between corrosion and exposure time (1-4 years). Atmospheric salinity is related with the monthly wind speed average, based on the concept of the wind run. chloride ion deposition rates of less than 300 mg Cl-l/m{sup 2}.d are related with remote (oceanic) winds and coastal winds basically of speeds between 1-40 km/h, while higher deposition rates (300-700 mg Cl-/m{sup 2}.d) correspond to coastal marine winds of a certain persistence with speeds of between 41-80 km/h. (Author) 39 refs.

Review of corrosion causes and corrosion control in a technical facility

International Nuclear Information System (INIS)

Charng, T.; Lansing, F.

1982-06-01

Causes of corrosion of metals and their alloys are reviewed. The corrosion mechanism is explained by electrochemical reaction theory. The causes and methods of controlling of both physiochemical corrosion and biological corrosion are presented. Factors which influence the rate of corrosion are also discussed

Condiciones de trabajo materno y bajo peso al nacer en la Ciudad de México

Directory of Open Access Journals (Sweden)

CERÓN-MIRELES PRUDENCIA

1997-01-01

Full Text Available Objetivo. Estudiar la asociación entre condiciones de trabajo materno y bajo peso al nacer en la Ciudad de México. Material y métodos. Se encuestaron 2 623 trabajadoras que atendieron sus partos en tres grandes hospitales de la Ciudad de México en 1992. Se obtuvo información sobre los principales factores biológicos y sociales que se asocian al bajo peso al nacer; asimismo, se determinó el estrés ocupacional utilizando el instrumento desarrollado por Karasek. Se utilizaron modelos de regresión logística para evaluar la relación de las condiciones de trabajo con el bajo peso al nacer, controlando por variables confusoras. Resultados. El bajo peso al nacer fue más alto en trabajadoras con jornadas mayores a 50 horas semanales (RM= 1.6; IC= 1.17, 2.28 y con conflictos laborales (RM= 1.5; IC= 1.0, 2.25. La falta de apoyo social tangible fue identificado como un factor de riesgo de bajo peso al nacer (RM= 1.7; IC= 1.20, 2.33. Las medidas preventivas laborales como el cambio de tareas, disminución de la jornada y las salidas por enfermedad no mostraron un efecto benéfico en el peso al nacer, a excepción de la licencia de maternidad; las madres que no la tuvieron mostraron una probabilidad 2.2 veces mayor para bajo peso al nacer (IC= 1.66, 2.93. Conclusiones. Estos hallazgos resaltan la importancia de identificar los factores de riesgo ocupacional en el embarazo..

Corrosion/95 conference papers

International Nuclear Information System (INIS)

Anon.

1995-01-01

The papers in this conference represent the latest technological advances in corrosion control and prevention. The following subject areas are covered: cathodic protection in natural waters; materials for fossil fuel combustion and conversion systems; modern problems in atmospheric corrosion; innovative ideas for controlling the decaying infrastructure; deposits and their effects on corrosion in industry; volatile high temperature and non aqueous corrosion inhibitors; corrosion of light-weight and precoated metals for automotive application; refining industry corrosion; corrosion in pulp and paper industry; arctic/cold weather corrosion; materials selection for waste incinerators and associated equipment; corrosion measurement technology; environmental cracking of materials; advancing technology in the coating industry; corrosion in gas treating; green inhibition; recent advances in corrosion control of rail equipment; velocity effects and erosion corrosion in oil and gas production; marine corrosion; corrosion of materials in nuclear systems; underground corrosion control; corrosion in potable and industrial water systems in buildings and its impact on environmental compliance; deposit related boiler tube failures; boiler systems monitoring and control; recent developments and experiences in reactive metals; microbiologically influenced corrosion; corrosion and corrosion control for steel reinforced concrete; international symposium on the use of 12 and 13 Cr stainless steels in oil and gas production environments; subsea corrosion /erosion monitoring in production facilities; fiberglass reinforced pipe and tubulars in oilfield service; corrosion control technology in power transmission and distribution; mechanisms and methods of scale and deposit control; closing the loop -- results oriented cooling system monitoring and control; and minimization of aqueous discharge

EUROCORR 2007 - The European corrosion congress - Progress by corrosion control. Book of Abstracts

International Nuclear Information System (INIS)

2007-01-01

This book of abstracts contains lectures, workshops and posters which were held on the European Corrosion Congress 2007 in Freiburg (Germany). The main topics of the sessions and posters are: 1. Corrosion and scale inhibition; 2. Corrosion by hot gases and combustion products; 3. Nuclear corrosion; 4. Environment sensitive fracture; 5. Surface Science; 6. Physico-chemical methods of corrosion testing; 7. Marine corrosion; 8. Microbial corrosion; 9. Corrosion of steel in concrete; 10. Corrosion in oil and gas production; 11. Coatings; 12. Corrosion in the refinery industry; 13. Cathodic protection; 14. Automotive Corrosion; 15. Corrosion of polymer materials. The main topics of the workshops are: 1. High temperature corrosion in the chemical, refinery and petrochemical industries; 2. Bio-Tribocorrosion; 3. Stress corrosion cracking in nuclear power plants; 4. Corrosion monitoring in nuclear systems; 5. Cathodic protection for marine and offshore environments; 6. Self-healing properties of new surface treatments; 7. Bio-Tribocorrosion - Cost 533/Eureka-ENIWEP-Meeting; 8. Drinking water systems; 9. Heat exchangers for seawater cooling

Corrosion and stress corrosion cracking in supercritical water

Science.gov (United States)

Was, G. S.; Ampornrat, P.; Gupta, G.; Teysseyre, S.; West, E. A.; Allen, T. R.; Sridharan, K.; Tan, L.; Chen, Y.; Ren, X.; Pister, C.

2007-09-01

Supercritical water (SCW) has attracted increasing attention since SCW boiler power plants were implemented to increase the efficiency of fossil-based power plants. The SCW reactor (SCWR) design has been selected as one of the Generation IV reactor concepts because of its higher thermal efficiency and plant simplification as compared to current light water reactors (LWRs). Reactor operating conditions call for a core coolant temperature between 280 °C and 620 °C at a pressure of 25 MPa and maximum expected neutron damage levels to any replaceable or permanent core component of 15 dpa (thermal reactor design) and 100 dpa (fast reactor design). Irradiation-induced changes in microstructure (swelling, radiation-induced segregation (RIS), hardening, phase stability) and mechanical properties (strength, thermal and irradiation-induced creep, fatigue) are also major concerns. Throughout the core, corrosion, stress corrosion cracking, and the effect of irradiation on these degradation modes are critical issues. This paper reviews the current understanding of the response of candidate materials for SCWR systems, focusing on the corrosion and stress corrosion cracking response, and highlights the design trade-offs associated with certain alloy systems. Ferritic-martensitic steels generally have the best resistance to stress corrosion cracking, but suffer from the worst oxidation. Austenitic stainless steels and Ni-base alloys have better oxidation resistance but are more susceptible to stress corrosion cracking. The promise of grain boundary engineering and surface modification in addressing corrosion and stress corrosion cracking performance is discussed.

Corrosion/96 conference papers

International Nuclear Information System (INIS)

Anon.

1996-01-01

Topics covered by this conference include: cathodic protection in natural waters; cleaning and repassivation of building HVAC systems; worldwide opportunities in flue gas desulfurization; advancements in materials technology for use in oil and gas service; fossil fuel combustion and conversion; technology of corrosion inhibitors; computers in corrosion control--modeling and information processing; recent experiences and advances of austenitic alloys; managing corrosion with plastics; corrosion measurement technology; corrosion inhibitors for concrete; refining industry; advances in corrosion control for rail and tank trailer equipment; CO 2 corrosion--mechanisms and control; microbiologically influenced corrosion; corrosion in nuclear systems; role of corrosion in boiler failures; effects of water reuse on monitoring and control technology in cooling water applications; methods and mechanisms of scale and deposit control; corrosion detection in petroleum production lines; underground corrosion control; environmental cracking--relating laboratory results and field behavior; corrosion control in reinforced concrete structures; corrosion and its control in aerospace and military hardware; injection and process addition facilities; progress reports on the results of reinspection of deaerators inspected or repaired per RP0590 criteria; near 100% volume solids coating technology and application methods; materials performance in high temperature environments containing halides; impact of toxicity studies on use of corrosion/scale inhibitors; mineral scale deposit control in oilfield related operations; corrosion in gas treating; marine corrosion; cold climate corrosion; corrosion in the pulp and paper industry; gaseous chlorine alternatives in cooling water systems; practical applications of ozone in recirculating cooling water systems; and water reuse in industry. Over 400 papers from this conference have been processed separately for inclusion on the data base

Corrosion/94 conference papers

International Nuclear Information System (INIS)

Anon.

1994-01-01

The approximately 500 papers from this conference are divided into the following sections: Rail transit systems--stray current corrosion problems and control; Total quality in the coatings industry; Deterioration mechanisms of alloys at high temperatures--prevention and remediation; Research needs and new developments in oxygen scavengers; Computers in corrosion control--knowledge based system; Corrosion and corrosivity sensors; Corrosion and corrosion control of steel reinforced concrete structures; Microbiologically influenced corrosion; Practical applications in mitigating CO 2 corrosion; Mineral scale deposit control in oilfield-related operations; Corrosion of materials in nuclear systems; Testing nonmetallics for life prediction; Refinery industry corrosion; Underground corrosion control; Mechanisms and applications of deposit and scale control additives; Corrosion in power transmission and distribution systems; Corrosion inhibitor testing and field application in oil and gas systems; Decontamination technology; Ozone in cooling water applications, testing, and mechanisms; Corrosion of water and sewage treatment, collection, and distribution systems; Environmental cracking of materials; Metallurgy of oil and gas field equipment; Corrosion measurement technology; Duplex stainless steels in the chemical process industries; Corrosion in the pulp and paper industry; Advances in cooling water treatment; Marine corrosion; Performance of materials in environments applicable to fossil energy systems; Environmental degradation of and methods of protection for military and aerospace materials; Rail equipment corrosion; Cathodic protection in natural waters; Characterization of air pollution control system environments; and Deposit-related problems in industrial boilers. Papers have been processed separately for inclusion on the data base

Caracterización parcial del proteoma del trofozoíto de Plasmodium falciparum bajo tratamiento con quinina, mefloquina y el compuesto natural diosgenona

Directory of Open Access Journals (Sweden)

César Segura

2014-06-01

Full Text Available Introducción. A pesar de los esfuerzos para controlar la malaria, esta sigue siendo un problema de salud pública. Plasmodium falciparum es responsable de la mayoría de los casos graves y de las muertes. Los programas de control de la malaria han sido cuestionados debido al fracaso del tratamiento y a la resistencia del parásito a los antipalúdicos de primera línea, por lo que se requieren nuevas y mejores alternativas. El análisis proteómico permite identificar y determinar los niveles de expresión de las proteínas bajo la presión de los medicamentos, lo que posibilita la identificación de nuevos blancos terapéuticos y mecanismos de acción. Objetivo. Analizar cualitativamente la expresión diferencial de proteínas del citosol del trofozoíto de P. falciparum bajo tratamiento con quinina, mefloquina y el compuesto natural diosgenona mediante una aproximación proteómica. Materiales y métodos. Se trataron trofozoítos sincronizados y cultivados in vitro de P. falciparum (cepa ITG2 con quinina, mefloquina y el compuesto natural diosgenona. Los extractos proteicos se prepararon y analizaron por electroforesis bidimensional. Las proteínas con aparente expresión diferencial se seleccionaron e identificaron mediante espectrometría de masas MALDI-TOF. Resultados. Se encontraron las siguientes proteínas diferencialmente expresadas en el trofozoíto: la enolasa (PF10_0155, la proteína de unión a calcio (PF11_0098, la chaperonina (PFL0740c, la proteína de invasión a la célula del huésped (PF10_0268 y la proteína relacionada con procesos de reducción y oxidación (redox (MAL8P1.17. Estos hallazgos son congruentes con resultados previos de estudios en los que el parásito fue presionado con otros medicamentos antipalúdicos. Conclusión. Los cambios observados en el perfil de proteínas del trofozoíto de P. falciparum tratado con antipalúdicos involucraron preferencialmente proteínas relacionadas con la respuesta al estr

Stress corrosion (Astm G30-90 standard) in 08x18H10T stainless steel of nuclear fuel storage pool in WWER reactors; Corrosion bajo esfuerzo (Norma ASTM G30-90) en acero inoxidable 08x18H10T de piscinas de almacenamiento de combustible nuclear en reactores V.V.E.R

Energy Technology Data Exchange (ETDEWEB)

Herrera, V.; Zamora R, L. [Centro de Estudios Aplicados al Desarrollo Nuclear (Cuba)

1997-07-01

At the water storage of the irradiated nuclear fuel has been an important factor in its management. The actual pools have its walls covered with inoxidable steel and heat exchangers to dissipate the residual heat from fuel. It is essential to control the water purity to eliminate those conditions which aid to the corrosion process in fuel and at related components. The steel used in this research was obtained from an austenitic inoxidizable steel standardized with titanium 08x18H10T (Type 321) similar to one of the two steel coatings used to cover walls and the pools floor. the test consisted in the specimen deformation through an U ply according to the Astm G30-90 standard. The exposition of the deformed specimen it was realized in simulated conditions to the chemical regime used in pools. (Author)

Corrosion technology. V. 1

International Nuclear Information System (INIS)

Khan, I.H.

1989-01-01

This book has been produced for dissemination of information on corrosion technology, corrosion hazards and its control. Chapter one of this book presents an overall view of the subject and chapter 2-5 deals with electrochemical basics, types of corrosion, pourbaix diagrams and form of corrosion. The author explains polarization/kinetics of corrosion, passivity, aqueous corrosion and corrosion testing and monitoring in 6-11 chapters. The author hopes it will provide incentive to all those interested in the corrosion technology. (A.B.)

A review on pipeline corrosion, in-line inspection (ILI), and corrosion growth rate models

International Nuclear Information System (INIS)

Vanaei, H.R.; Eslami, A.; Egbewande, A.

2017-01-01

Pipelines are the very important energy transmission systems. Over time, pipelines can corrode. While corrosion could be detected by in-line inspection (ILI) tools, corrosion growth rate prediction in pipelines is usually done through corrosion rate models. For pipeline integrity management and planning selecting the proper corrosion ILI tool and also corrosion growth rate model is important and can lead to significant savings and safer pipe operation. In this paper common forms of pipeline corrosion, state of the art ILI tools, and also corrosion growth rate models are reviewed. The common forms of pipeline corrosion introduced in this paper are Uniform/General Corrosion, Pitting Corrosion, Cavitation and Erosion Corrosion, Stray Current Corrosion, Micro-Bacterial Influenced Corrosion (MIC). The ILI corrosion detection tools assessed in this study are Magnetic Flux Leakage (MFL), Circumferential MFL, Tri-axial MFL, and Ultrasonic Wall Measurement (UT). The corrosion growth rate models considered in this study are single-value corrosion rate model, linear corrosion growth rate model, non-linear corrosion growth rate model, Monte-Carlo method, Markov model, TD-GEVD, TI-GEVD model, Gamma Process, and BMWD model. Strengths and limitations of ILI detection tools, and also corrosion predictive models with some practical examples are discussed. This paper could be useful for those whom are supporting pipeline integrity management and planning. - Highlights: • Different forms of pipeline corrosion are explained. • Common In-Line Inspection (ILI) tools and corrosion growth rate models are introduced. • Strength and limitations of corrosion growth rate models/ILI tools are discussed. • For pipeline integrity management programs using more than one corrosion growth rate model/ILI tool is suggested.

Erosion and erosion-corrosion

International Nuclear Information System (INIS)

Isomoto, Yoshinori

2008-01-01

It is very difficult to interpret the technical term of erosion-corrosion' which is sometimes encountered in piping systems of power plants, because of complicated mechanisms and several confusing definitions of erosion-corrosion phenomena. 'FAC (flow accelerated corrosion)' is recently introduced as wall thinning of materials in power plant systems, as a representative of 'erosion-corrosion'. FAC is, however, not necessarily well understood and compared with erosion-corrosion. This paper describes firstly the origin, definition and fundamental understandings of erosion and erosion-corrosion, in order to reconsider and reconfirm the phenomena of erosion, erosion-corrosion and FAC. Next, typical mapping of erosion, corrosion, erosion-corrosion and FAC are introduced in flow velocity and environmental corrosiveness axes. The concept of damage rate in erosion-corrosion is finally discussed, connecting dissolution rate, mass transfer of metal ions in a metal oxide film and film growth. (author)

Túnel bajo el agua

Directory of Open Access Journals (Sweden)

Stamhuis, E.

1964-03-01

Full Text Available This article describes the results obtained by the Dutch Central Institute of Scientific Research when studying the problem of underwater tunnels. This Institute has sought to establish general specifications for the design of this type of tunnels, so that they shall be more efficient than those at present in use. Firstly, a study was made of the strength, waterproof qualities, and most rational type of ventilation, with a view to drawing up of general principles on this aspect of the design. An analysis is given of the shape, suitable cross sections and constructive methods, and these are compared with those adopted in the construction of underwater tunnels at present in use in America. Particular attention has been given to designs which are largely based on prefabrication and the use of factory made structural parts, and also on the transport and erection of these at the site. The author goes on to discuss the interplay of soil and water pressures, buoyancy forces, and cases in which the tunnel is subjected to important bending and shear forces on particular sections of it. In this connection care is taken to give the theoretical considerations a ready practical interpretation. In particular, a description is given of special distance pieces which connect the two tubes making up a tunnel, also the system of joining two sections of the tube, and the measure of watertightness and flexibility which such joints provide. Finally, a summary is given of the theoretical foundations, as well as a number of observations and items of advise, which are applicable to these types of structures.El ingeniero A. Eggink describió, en un trabajo publicado últimamente, un nuevo tipo de túnel bajo el agua para canalizar la circulación rodada. En este trabajo se desarrolla un análisis sobre las consideraciones que han jugado un papel predominante en la redacción del proyecto de ejecución de un túnel subacuo. Acompañan al trabajo los resultados referentes

Accelerated Corrosion Testing

Science.gov (United States)

1982-12-01

Treaty Organization, Brussels, 1971), p. 449. 14. D. 0. Sprowls, T. J. Summerson, G. M. Ugianski, S. G. Epstein, and H. L. Craig , Jr., in Stress...National Association of Corrosion Engineers Houston, TX, 1972). 22. H. L. Craig , Jr. (ed.), Stress Corrosion-New Approaches, ASTM-STP- 610 (American...62. M. Hishida and H. Nakada, Corrosion 33 (11) 403 (1977). b3. D. C. Deegan and B. E. Wilde, Corrosion 34 (6), 19 (1978). 64. S. Orman, Corrosion Sci

INTENSIDAD DE LA MUSICA: EFECTO SOBRE LA FRECUENCIA CARDIACA Y EL ESFUERZO PERCIBIDO DURANTE LA ACTIVIDAD FISICA

Directory of Open Access Journals (Sweden)

Jorge Marín Hernández

2001-12-01

Full Text Available La música ha sido ampliamente utilizada en la práctica de ejercicios aeróbicos en la industria deportiva. El propósito de este estudio fue comparar el efecto de diferentes intensidades de la música sobre la frecuencia cardiaca (FC y el esfuerzo percibido (EP durante ejercicio estandarizado en un cicloergómetro. 13 hombres y 5 mujeres voluntarios, físicamente activos (edad 20.6 ± 2.2 años realizaron una prueba bajo tres condiciones en diferentes días, asignadas en un diseño contrabalanceado de medidas repetidas: no música (NM, música a 70 dB, (M70 y música a 85 dB (M85. Ellos se ejercitaron por 20 min. con una carga de trabajo constante predeterminada y equivalente al 80% de su FCMax (kp = 1.47 ± 0.4, 90 rev/min. La música utilizada fue del tipo 'Merengue House' en español con un tempo de 131 ± 4.30 bpm, las diferentes intensidades fueron calibradas con un sonómetro. La FC y el EP fueron registrados a los 10 y 20 min. con un monitor de FC Polar y la escala EP-15 de Borg. Prueba FC 10 min. FC 20 min. EP 10 min. EP 20 min. NM 164.78 ± 8.37 172.11 ± 8.54 12.06 ±1.92 13.78 ±2.58 M70 165.11 ±11.16 173.00 ±12.05 12.00 ±2.11 13.56 ±2.89 M85 163.00 ± 7.58 170.17 ± 7.87 11.50 ±1.55 12.94 ±2.07 Tanto para FC como para EP un ANOVA 3 x 2 con medidas repetidas indicó que los promedios a los 20 min. fueron significativamente mayores que a los 10 min. (p<0.05. Las diferencias en FC y EP entre las tres condiciones no fueron significativas (p >0.05. Los resultados indican que los rangos de intensidades de música estudiados M70 y M85 no produjeron un efecto sobre el EP y la FC cuando se realizó ejercicio estandarizado en un cicloergómetro comparado con una condición sin música NM.

Concrete cover cracking with reinforcement corrosion of RC beam during chloride-induced corrosion process

International Nuclear Information System (INIS)

Zhang Ruijin; Castel, Arnaud; Francois, Raoul

2010-01-01

This paper deals with the evolution of the corrosion pattern based on two beams corroded by 14 years (beam B1CL1) and 23 years (beam B2CL1) of conservation in a chloride environment. The experimental results indicate that, at the cracking initiation stage and the first stage of cracking propagation, localized corrosion due to chloride ingress is the predominant corrosion pattern and pitting corrosion is the main factor that influences the cracking process. As corrosion cracking increases, general corrosion develops rapidly and gradually becomes predominant in the second stage of cracking propagation. A comparison between existing models and experimental results illustrates that, although Vidal et al.'s model can better predict the reinforcement corrosion of beam B1CL1 under localized corrosion, it cannot predict the corrosion of beam B2CL1 under general corrosion. Also, Rodriguez's model, derived from the general corrosion due to electrically accelerated corrosion experiments, cannot match natural chloride corrosion irrespective of whether corrosion is localized or general. Thus, for natural general corrosion in the second stage of cracking propagation, a new model based on the parameter of average steel cross-section loss is put forward to predict steel corrosion from corrosion cracking.

Perubahan Sosial Pada Komunitas Suku Bajo Di Pesisir Teluk Tomini

Directory of Open Access Journals (Sweden)

Muhammad Obie

2016-06-01

Full Text Available Abstract: Society and culture of human being always change as an ever –present phenomena in the world. A distinction is sometimes made then between processes of change within the social structure, which serve in part to maintain the structure, and, even the processes itself can be slow or fast through evolusion and revolusion.   One of the factors that quicken the social change process is the government interventions. This study aims at analyzing the social change on the Bajo Tribe community as the impact of various government programs at Tomini bay coastal. This research used strategy of historical sociology. The kinds of data collected were primer and secondary data that were analyzed by using qualitative approac. The result showed that various   government programs at Tomini bay, such as designating conservation area, granting concession license to private sectors through forest concession right (FCR, indefeasible right of use (IRU, and fishing industry at the bay had caused the loss of access of the Bajo tribe community to coastal and marine resources area. Various interventions of government programs had implication on resettlement of the Bajo tribe community, causing the Bajo tribe divided into sea Bajo and land Bajo. The loss of access of the Bajo tribe to coastal and marine resources caused traditional institution weaken which made its philosophy of living in harmony with nature, and  conservation ethics fade away, its local wisdom, and self identity lose, and its social capital destructed.  الملخص: كان المجتمع وحضارته متغيّرين في أيّ كان المجتمع وهذه الحضارة. ويكون الفرق في كون هذا التغيّر. قد تكون عملية التغيّر متمهّلة أو سريعة وقد تكون عن طريق التطوّر والثّورة. وأحد العناصر المسرعة في عملية هذا التغيّر هو تدخّل الحكومة. حاولت هذه �

Humid-air and aqueous corrosion models for corrosion-allowance barrier material

International Nuclear Information System (INIS)

Lee, J.H.; Atkins, J.E.; Andrews, R.W.

1995-01-01

Humid-air and aqueous general and pitting corrosion models (including their uncertainties) for the carbon steel outer containment barrier were developed using the corrosion data from literature for a suite of cast irons and carbon steels which have similar corrosion behaviors to the outer barrier material. The corrosion data include the potential effects of various chemical species present in the testing environments. The atmospheric corrosion data also embed any effects of cyclic wetting and drying and salts that may form on the corroding specimen surface. The humid-air and aqueous general corrosion models are consistent in that the predicted humid-air general corrosion rates at relative humidities between 85 and 100% RH are close to the predicted aqueous general corrosion rates. Using the expected values of the model parameters, the model predicts that aqueous pitting corrosion is the most likely failure mode for the carbon steel outer barrier, and an earliest failure (or initial pit penetration) of the 100-mm thick barrier may occur as early as about 500 years if it is exposed continuously to an aqueous condition at between 60 and 70 degrees C

Quantitative measures of corrosion and prevention: application to corrosion in agriculture

NARCIS (Netherlands)

Schouten, J.C.; Gellings, P.J.

1987-01-01

The corrosion protection factor (c.p.f.) and the corrosion condition (c.c.) are simple instruments for the study and evaluation of the contribution and efficiency of several methods of corrosion prevention and control. The application of c.p.f. and c.c. to corrosion and prevention in agriculture in

Evaluation of corrosive behavior of SAE 5155 by corrosion environment

International Nuclear Information System (INIS)

An, Jae Pil; Park, Keyung Dong

2005-01-01

In this study, the influence of shot peening and corrosive condition for corrosion property was investigated on immersed in 3.5% NaCl, 10% HNO 3 + 3% HF, 6% FeCl 3 . The immersion test was performed on two kinds of specimen. The immersion periods was performed 30days. Corrosion potential, weight loss were investigated from experimental results. From test results, the effect of shot peening on the corrosion was evaluated

The effect of corrosion on stained glass windows

Directory of Open Access Journals (Sweden)

Laissner, Johanna

1996-06-01

Full Text Available Stained glass windows belong to the most important cultural heritage of Europe. Within the last decades a disastrous deterioration took place. The wonderful stained glass windows and their glass paintings as pieces of art are acutely menaced by environmental corrosive influences. This corrosion process is a very complex reaction which is not only influenced by temperature and humidity changes but also by gaseous pollutants like sulfur dioxide, nitrogen oxides or ozone, by dust and air, microorganisms as well as synergetic interactions. Strongly affected by these environmental attacks are medieval stained glasses due to their chemical composition. They have a low content in silica and high contents of modifier ions (e.g. potassium and calcium. The corrosion phenomena can range from predominantly pitting on the surface to the formation of thick corrosion crusts which are turning the panel opaque and thus reducing strongly the transparency of the windows. In order to set up a conservation and restoration concept, it is necessary to know about the environmental conditions to which the stained glass windows are exposed. For this purpose very corrosion sensitive model glasses (so called glass sensors were developed which have a similar chemical composition as historic stained glasses. They exhibit the same corrosion reactions but react much faster, and are now widely used to estimate corrosive stresses on stained glass windows to give basic information about the corrosive impacts which work on the historic glasses. In this paper principle corrosion mechanisms of stained glass windows and their enhancing factors are discussed. For the evaluation of the environmental impact, the application of glass sensors is demonstrated.

Las vidrieras coloreadas pertenecen al legado cultural más importante de Europa. En las últimas décadas se ha producido en ellas un desastroso deterioro. Las maravillosas vidrieras coloreadas y sus policromías est

Synergy effect of naphthenic acid corrosion and sulfur corrosion in crude oil distillation unit

Science.gov (United States)

Huang, B. S.; Yin, W. F.; Sang, D. H.; Jiang, Z. Y.

2012-10-01

The synergy effect of naphthenic acid corrosion and sulfur corrosion at high temperature in crude oil distillation unit was studied using Q235 carbon-manganese steel and 316 stainless steel. The corrosion of Q235 and 316 in corrosion media containing sulfur and/or naphthenic acid at 280 °C was investigated by weight loss, scanning electron microscope (SEM), EDS and X-ray diffractometer (XRD) analysis. The results showed that in corrosion media containing only sulfur, the corrosion rate of Q235 and 316 first increased and then decreased with the increase of sulfur content. In corrosion media containing naphthenic acid and sulfur, with the variations of acid value or sulfur content, the synergy effect of naphthenic acid corrosion and sulfur corrosion has a great influence on the corrosion rate of Q235 and 316. It was indicated that the sulfur accelerated naphthenic acid corrosion below a certain sulfur content but prevented naphthenic acid corrosion above that. The corrosion products on two steels after exposure to corrosion media were investigated. The stable Cr5S8 phases detected in the corrosion products film of 316 were considered as the reason why 316 has greater corrosion resistance to that of Q235.

Bajo materialismo y surrealismo. El debate Bataille-Breton

Directory of Open Access Journals (Sweden)

Noelia Denise Dunan

2015-01-01

Full Text Available Hacia 1923 Georges Bataille era un joven desconocido que comenzaba a entablar amistades y también enemistades en el núcleo del movimiento surrealista e intelectual de París. Alentado por algunos de aquellos vínculos, lee a Mauss y Durkheim, Nietzsche y Freud y, comienza a delinear un pensamiento que se plasmará en la creación de Documents. Resulta difícil comprender la relevancia de esta revista y la producción batailleana sin referir a sus primeras lecturas y al debate que tempranamente entabló con el máximo exponente del movimiento surrealista, André Breton. Bataille coordinó allí un grupo de disidentes y convirtió la publicación en una máquina contra el surrealismo. El presente artículo desarrolla la formación de Bataille para hacer hincapié en la categoría de bajo materialismo construida en tensión entre el idealismo surrealista y los distintos materialismos. Así puede verse que Documents y el bajo materialismo conjugan las preocupaciones que perseguirá toda su vida.

Degradation of aged plants by corrosion: 'Long cell action' in unresolved corrosion issues

International Nuclear Information System (INIS)

Saji, Genn

2009-01-01

In a series of previously published papers the author has identified that 'long cell action' corrosion plays a pivotal role in practically all unresolved corrosion issues for all types of nuclear power plants (e.g. PWR/VVER, BWR/RBMK and CANDU). Some of these unresolved issues are IGSCC, PWSCC, AOA and FAC (erosion-corrosion). In conventional corrosion science it is well established that 'long cell action' can seriously accelerate or suppress the local cell corrosion activities. Although long cell action is another fundamental mechanism of corrosion, especially in a 'soil corrosion' arena, potential involvement of this corrosion process has never been studied in nuclear and fossil power plants as far as the author has been able to establish. The author believes that the omission of this basic corrosion mechanism is the root cause of practically all un-resolved corrosion issues. In this paper, the author further elaborated on his assessment to other key corrosion issues, e.g. steam generator and turbine corrosion issues, while briefly summarizing previous discussions for completeness purposes, as well as introducing additional experimental and theoretical evidence of this basic corrosion mechanism. Due to the importance of this potential mechanism the author is calling for institutional review activities and further verification experiments in the form of a joint international project.

Corrosion Testing Facility

Data.gov (United States)

Federal Laboratory Consortium — The Corrosion Testing Facility is part of the Army Corrosion Office (ACO). It is a fully functional atmospheric exposure site, called the Corrosion Instrumented Test...

Velocidad de onda y módulos de elasticidad por ultrasonido y ondas de esfuerzo de vigas de madera de Pinus spp. mexicana

Directory of Open Access Journals (Sweden)

Javier Sotomayor

2015-04-01

Full Text Available La industria de edificación con madera requiere datos de resistencia mecánica de madera con dimensiones y clasificación apropiadas para su uso como elementos estructurales. La presente investigación propone una estrategia experimental para la caracterización mecánica de vigas de madera y su aplicación como material de Ingeniería. El objetivo de la investigación fue: determinar las velocidades de onda y los módulos de elasticidad de vigas de Pinus spp., empleando ultrasonido y ondas de esfuerzo estudiando 70 vigas de Pinus spp. con dimensiones de 0.10 m x 0.15 m de sección transversal, 35 vigas de 5 m y 35 de 6 m de longitud. Las velocidades de transmisión presentaron coeficientes de variación coherentes a la heterogeneidad estructural de la madera. Los valores de estos coeficientes se incrementaron cuando se calcularon características de segundo nivel, como es el caso de los módulos de elasticidad. La velocidad y el módulo de elasticidad mostraron un carácter de anisotropía importante para el cálculo de la resistencia mecánica de las vigas. Igualmente, los parámetros calculados con el método de ondas de esfuerzo resultaron mayores a los determinados con ultrasonido. Los resultados permiten concluir que las técnicas de ultrasonido y ondas de esfuerzo pueden determinar la velocidad de onda y los módulos de elasticidad de vigas de madera de Pinus spp.

Synergy effect of naphthenic acid corrosion and sulfur corrosion in crude oil distillation unit

Energy Technology Data Exchange (ETDEWEB)

Huang, B.S., E-mail: yinwenfeng2010@163.com [College of Materials Science and Engineering, Southwest Petroleum University, Sichuan, Chengdu, 610500 (China); Yin, W.F. [College of Mechatronic Engineering, Southwest Petroleum University, Sichuan, Chengdu, 610500 (China); Sang, D.H. [Sheng Li Construction Group International Engineering Department, Shandong, Dongying, 257000 (China); Jiang, Z.Y. [College of Materials Science and Engineering, Southwest Petroleum University, Sichuan, Chengdu, 610500 (China)

2012-10-15

Highlights: Black-Right-Pointing-Pointer The corrosion of a carbon-manganese steel and a stainless steel in sulfur and/or naphthenic acid media was investigated. Black-Right-Pointing-Pointer The corrosion rate of the carbon-manganese steel increased with the increase of the acid value and sulfur content. Black-Right-Pointing-Pointer The critical values of the concentration of sulfur and acid for corrosion rate of the stainless steel were ascertained respectively. Black-Right-Pointing-Pointer The stainless steel is superior to the carbon-manganese steel in corrosion resistance because of the presence of stable Cr{sub 5}S{sub 8} phases. - Abstract: The synergy effect of naphthenic acid corrosion and sulfur corrosion at high temperature in crude oil distillation unit was studied using Q235 carbon-manganese steel and 316 stainless steel. The corrosion of Q235 and 316 in corrosion media containing sulfur and/or naphthenic acid at 280 Degree-Sign C was investigated by weight loss, scanning electron microscope (SEM), EDS and X-ray diffractometer (XRD) analysis. The results showed that in corrosion media containing only sulfur, the corrosion rate of Q235 and 316 first increased and then decreased with the increase of sulfur content. In corrosion media containing naphthenic acid and sulfur, with the variations of acid value or sulfur content, the synergy effect of naphthenic acid corrosion and sulfur corrosion has a great influence on the corrosion rate of Q235 and 316. It was indicated that the sulfur accelerated naphthenic acid corrosion below a certain sulfur content but prevented naphthenic acid corrosion above that. The corrosion products on two steels after exposure to corrosion media were investigated. The stable Cr{sub 5}S{sub 8} phases detected in the corrosion products film of 316 were considered as the reason why 316 has greater corrosion resistance to that of Q235.

Factores de riesgo de bajo peso al nacer en un hospital cubano, 1997-2000

Directory of Open Access Journals (Sweden)

Escobar José Andrés Cabrales

2002-01-01

Full Text Available Objetivo. Identificar qué factores de riesgo materno durante el embarazo se asocian a la incidencia de bajo peso al nacer (menos de 2 500 g. Métodos. Se diseñó un estudio de casos y testigos con 764 casos de nacimiento simple con un peso al nacer de menos de 2 500 g, y 1 437 testigos del Hospital Gineco-Obstétrico Provincial de Sancti Spíritus, Cuba, durante el cuatrienio de 1997-2000. Los datos se obtuvieron de historias clínicas, registros de partos y entrevistas personales con las madres. Se realizó un análisis con dos variables y se controlaron los posibles factores de confusión mediante regresión logística dicotómica con el programa SPSS. Se usó un modelo final de múltiples variables para identificar los factores de riesgo maternos asociados con el bajo peso al nacer. Resultados. El análisis con múltiples variables mostró una asociación significativa del bajo peso al nacer con la presencia de anemia en la madre cuando se detectó el embarazo, la sepsis urinaria durante el embarazo, el asma bronquial, un aumento de peso materno menor de 8 kg durante todo el embarazo, el hábito de fumar durante el mismo, antecedentes de bajo peso al nacer en partos anteriores, la presencia de hipertensión arterial desde antes de la gestación y la consulta prenatal extemporánea. Conclusiones. A partir de estos resultados se concluyó que, independientemente de la medida de impacto utilizada, es importante tratar de disminuir los factores de riesgo identificados a fin de reducir la incidencia del bajo peso al nacer en la provincia de Sancti Spíritus.

Factores de riesgo de bajo peso al nacer en un hospital cubano, 1997-2000

Directory of Open Access Journals (Sweden)

José Andrés Cabrales Escobar

2002-09-01

Full Text Available Objetivo. Identificar qué factores de riesgo materno durante el embarazo se asocian a la incidencia de bajo peso al nacer (menos de 2 500 g. Métodos. Se diseñó un estudio de casos y testigos con 764 casos de nacimiento simple con un peso al nacer de menos de 2 500 g, y 1 437 testigos del Hospital Gineco-Obstétrico Provincial de Sancti Spíritus, Cuba, durante el cuatrienio de 1997-2000. Los datos se obtuvieron de historias clínicas, registros de partos y entrevistas personales con las madres. Se realizó un análisis con dos variables y se controlaron los posibles factores de confusión mediante regresión logística dicotómica con el programa SPSS. Se usó un modelo final de múltiples variables para identificar los factores de riesgo maternos asociados con el bajo peso al nacer. Resultados. El análisis con múltiples variables mostró una asociación significativa del bajo peso al nacer con la presencia de anemia en la madre cuando se detectó el embarazo, la sepsis urinaria durante el embarazo, el asma bronquial, un aumento de peso materno menor de 8 kg durante todo el embarazo, el hábito de fumar durante el mismo, antecedentes de bajo peso al nacer en partos anteriores, la presencia de hipertensión arterial desde antes de la gestación y la consulta prenatal extemporánea. Conclusiones. A partir de estos resultados se concluyó que, independientemente de la medida de impacto utilizada, es importante tratar de disminuir los factores de riesgo identificados a fin de reducir la incidencia del bajo peso al nacer en la provincia de Sancti Spíritus.

Erosion-corrosion

International Nuclear Information System (INIS)

Aghili, B.

1999-05-01

A literature study on erosion-corrosion of pipings in the nuclear industry was performed. Occurred incidents are reviewed, and the mechanism driving the erosion-corrosion is described. Factors that influence the effect in negative or positive direction are treated, as well as programs for control and inspection. Finally, examples of failures from databases on erosion-corrosion are given in an attachment

Corrosion behaviors and effects of corrosion products of plasma electrolytic oxidation coated AZ31 magnesium alloy under the salt spray corrosion test

International Nuclear Information System (INIS)

Wang, Yan; Huang, Zhiquan; Yan, Qin; Liu, Chen; Liu, Peng; Zhang, Yi; Guo, Changhong; Jiang, Guirong; Shen, Dejiu

2016-01-01

Highlights: • Corrosion behaviors of a PEO coating was investigated after the salt spray test. • Corrosion products have significant effects on corrosion behaviors of the coating. • An electrochemical corrosion model is proposed. - Abstract: The effects of corrosion products on corrosion behaviors of AZ31 magnesium alloy with a plasma electrolytic oxidation (PEO) coating were investigated under the salt spray corrosion test (SSCT). The surface morphology, cross-sectional microstructure, chemical and phase compositions of the PEO coating were determined using scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction analysis (XRD), respectively. Further, the corrosion process of the samples under the SSCT was examined in a non-aqueous electrolyte (methanol) using electrochemical impedance spectroscopy (EIS) coupled with equivalent circuit. The results show that the inner layer of the coating was destroyed firstly and the corrosion products have significant effects on the corrosion behaviors of the coating. The results above are discussed and an electrochemical corrosion model is proposed in the paper.

Corrosion behaviors and effects of corrosion products of plasma electrolytic oxidation coated AZ31 magnesium alloy under the salt spray corrosion test

Energy Technology Data Exchange (ETDEWEB)

Wang, Yan; Huang, Zhiquan; Yan, Qin; Liu, Chen; Liu, Peng; Zhang, Yi [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Guo, Changhong; Jiang, Guirong [College of Mechanical Engineering, Yanshan University, Qinhuangdao 066004 (China); Shen, Dejiu, E-mail: DejiuShen@163.com [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China)

2016-08-15

Highlights: • Corrosion behaviors of a PEO coating was investigated after the salt spray test. • Corrosion products have significant effects on corrosion behaviors of the coating. • An electrochemical corrosion model is proposed. - Abstract: The effects of corrosion products on corrosion behaviors of AZ31 magnesium alloy with a plasma electrolytic oxidation (PEO) coating were investigated under the salt spray corrosion test (SSCT). The surface morphology, cross-sectional microstructure, chemical and phase compositions of the PEO coating were determined using scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction analysis (XRD), respectively. Further, the corrosion process of the samples under the SSCT was examined in a non-aqueous electrolyte (methanol) using electrochemical impedance spectroscopy (EIS) coupled with equivalent circuit. The results show that the inner layer of the coating was destroyed firstly and the corrosion products have significant effects on the corrosion behaviors of the coating. The results above are discussed and an electrochemical corrosion model is proposed in the paper.

Stress corrosion and corrosion fatigue crack growth monitoring in metals

International Nuclear Information System (INIS)

Senadheera, T.; Shipilov, S.A.

2003-01-01

Environmentally assisted cracking (including stress corrosion cracking and corrosion fatigue) is one of the major causes for materials failure in a wide variety of industries. It is extremely important to understand the mechanism(s) of environmentally assisted crack propagation in structural materials so as to choose correctly from among the various possibilities-alloying elements, heat treatment of steels, parameters of cathodic protection, and inhibitors-to prevent in-service failures due to stress corrosion cracking and corrosion fatigue. An important step towards understanding the mechanism of environmentally assisted crack propagation is designing a testing machine for crack growth monitoring and that simultaneously provides measurement of electrochemical parameters. In the present paper, a direct current (DC) potential drop method for monitoring crack propagation in metals and a testing machine that uses this method and allows for measuring electrochemical parameters during stress corrosion and corrosion fatigue crack growth are described. (author)

General Corrosion and Localized Corrosion of Waste Package Outer Barrier

Energy Technology Data Exchange (ETDEWEB)

K.G. Mon

2004-10-01

The waste package design for the License Application is a double-wall waste package underneath a protective drip shield (BSC 2004 [DIRS 168489]; BSC 2004 [DIRS 169480]). The purpose and scope of this model report is to document models for general and localized corrosion of the waste package outer barrier (WPOB) to be used in evaluating waste package performance. The WPOB is constructed of Alloy 22 (UNS N06022), a highly corrosion-resistant nickel-based alloy. The inner vessel of the waste package is constructed of Stainless Steel Type 316 (UNS S31600). Before it fails, the Alloy 22 WPOB protects the Stainless Steel Type 316 inner vessel from exposure to the external environment and any significant degradation. The Stainless Steel Type 316 inner vessel provides structural stability to the thinner Alloy 22 WPOB. Although the waste package inner vessel would also provide some performance for waste containment and potentially decrease the rate of radionuclide transport after WPOB breach before it fails, the potential performance of the inner vessel is far less than that of the more corrosion-resistant Alloy 22 WPOB. For this reason, the corrosion performance of the waste package inner vessel is conservatively ignored in this report and the total system performance assessment for the license application (TSPA-LA). Treatment of seismic and igneous events and their consequences on waste package outer barrier performance are not specifically discussed in this report, although the general and localized corrosion models developed in this report are suitable for use in these scenarios. The localized corrosion processes considered in this report are pitting corrosion and crevice corrosion. Stress corrosion cracking is discussed in ''Stress Corrosion Cracking of the Drip Shield, the Waste Package Outer Barrier, and the Stainless Steel Structural Material'' (BSC 2004 [DIRS 169985]).

Low carbon steel corrosion damage prediction in rural and urban environments

Directory of Open Access Journals (Sweden)

Díaz, V.

2003-12-01

Full Text Available This paper presents an Artificial Neural Network (ANN model for the damage function of carbon steel, expressed in μm of corrosion penetration as a function of environmental variables. Working in the context of the Iberoamerican Atmospheric Corrosion Map Project, the experimental data comes as result of the corrosion of low alloy steel subtracts in three test sites in Uruguay, South America. In addition, we included experimental values obtained from short time kinetics studies, corresponding to special series from one of the sites. The ANN numerical model shows attractive results regarding goodness of fit and residual distributions. It achieves a RMSE value of 0.5 μm while a classical regression model lies in the range of 4.1 μm. Furthermore, a properly adjusted ANN model can be useful in the prediction of corrosion damage under different climatological and pollution conditions, while linear models cannot.

Este artículo presenta la metodología de las redes neuronales artificiales (RNA como solución para el modelado de los valores experimentales obtenidos en los procesos de corrosión atmosférica. Se desarrolla el modelo de RNA para la función de daño, expresada en μm de penetración para el acero de bajo carbono en función de las variables medioambientales, en el contexto del Proyecto MICAT (Mapa Iberoamericano de Corrosión Atmosférica y programas de experimentación propios. Los datos experimentales son resultado de los estudios de calibración sobre sustratos ferrosos en tres sitios del territorio uruguayo, Sudamérica. Se incluyen, además, los valores experimentales obtenidos en los estudios de cinéticas iniciales, correspondientes a series especiales de cortos tiempos de exposición en una de las estaciones de ensayo. El modelo numérico de RNA muestra resultados con un valor de RMSE de 0,5 μm, en tanto el modelo de regresión clásico arroja un valor de 4,1 μm.

THE CONSTRUCTION AND CONTESTATION OF ISLAMIC IDENTITY OF THE BAJO PEOPLE IN WAKATOBI ISLANDS, SOUTH EAST SULAWESI, INDONESIA

Directory of Open Access Journals (Sweden)

Benny Baskara

2014-02-01

Full Text Available On the one one hand, the Bajo people are well-known as ‘the sea people’ who have their own indigenous belief system – belief in the Lord of the Sea. On the other hand, they also acknowledge themselves as Muslims. Thus, the religious identity of the Bajo people reflects a unique combination of Islamic teachings and their indigenous beliefs. This unique combination is not only expressed in their religious life, in their rituals and worship practices, but also in the values found in their customary practices (adat as a guiding system for their life. This paper examines the construction and contestation of the religious identity of the Bajo people, especially how they construct their identities in relation to their natural, social, and religious environments. The contestation of the Bajo religious identity covers three aspects: the contestation of the Islam of ‘the sea people’ against the Islam of ‘the land people’, the contenstation of the ‘official’ Islam against the ‘traditional’ Islam, and the challenges of modernity, especially the commodification of the Bajo religious expressions. This contestation, in turn, reconstructs their religious identity into a more adaptive one.

Corrosion and anticorrosion. Industrial practice

International Nuclear Information System (INIS)

Beranger, G.; Mazille, H.

2002-01-01

This book comprises 14 chapters written with the collaboration of about 50 French experts of corrosion. It is complementary to another volume entitled 'corrosion of metals and alloys' and published by the same editor. This volume comprises two parts: part 1 presents the basic notions of corrosion phenomena, the properties of surfaces, the electrochemical properties of corrosion etc.. Part 2 describes the most frequent forms of corrosion encountered in industrial environments and corresponding to specific problems of protection: marine environment, atmospheric corrosion, galvanic corrosion, tribo-corrosion, stress corrosion etc.. The first 8 chapters (part 1) treat of the corrosion problems encountered in different industries and processes: oil and gas production, chemical industry, phosphoric acid industry, PWR-type power plants, corrosion of automobile vehicles, civil engineering and buildings, corrosion of biomaterials, non-destructive testing for the monitoring of corrosion. The other chapters (part 2) deal with anticorrosion and protective coatings and means: choice of materials, coatings and surface treatments, thick organic coatings and enamels, paints, corrosion inhibitors and cathodic protection. (J.S.)

Corrosion principles and surface modification

International Nuclear Information System (INIS)

Kruger, J.

1982-01-01

This chapter examines the important strategies provided by the newer ideas of corrosion science and engineering that surface modification techniques must utilize to help prevent corrosion, especially the most damaging kind of aqueous corrosion, localized corrosion. Provides a brief introduction to the principles underlying the phenomenon of corrosion in order to use them to discuss surface modification strategies to combat corrosion. Discusses the electrochemistry of corrosion; the thermodynamics of corrosion; the kinetics of corrosion; thermodynamic strategies; and kinetic strategies (formation of more protective passive films; resistance to breakdown; ductility; repassivation)

Perfil cognitivo de niños con rendimientos bajos en comprensión lectora

Directory of Open Access Journals (Sweden)

Lorena Canet-Juric

2013-10-01

Full Text Available La mayoría de los niños con dificultades en la comprensión lectora poseen rendimientos inferiores en un conjunto de procesos cognitivos. El objetivo del presente estudio es establecer un perfil cognitivo asociado al bajo rendimiento en comprensión lectora en relación a la habilidad de monitoreo, a la producción de inferencias, al vocabulario, a la amplitud de memoria de trabajo y a la capacidad inhibitoria, en niños hispanoparlantes. Para ello se administraron tareas correspondientes a dichos procesos en niños con altos y bajos rendimientos en comprensión lectora. Los resultados mostraron que si bien los niños con mala comprensión presentan bajos rendimientos en estas habilidades, no puede establecerse un perfil consistente ya que hay niños con problemas en comprensión que presentan normal o superior rendimiento en algunas de estas habilidades cognitivas.

Development of Copper Corrosion Products and Relation between Surface Appearance and Corrosion Rate

International Nuclear Information System (INIS)

Lan, Tran Thi Ngoc; Binh, Nguyen Thi Thanh; Tru, Nguyen Nhi; Yoshino, Tsujino; Yasuki, Maeda

2008-01-01

Copper was exposed unsheltered and sheltered in four humid tropical sites, representing urban, urban-industrial, urban-marine and rural environments. The corrosion rates and the sequence of corrosion product formation are presented and discussed in relation with climatic and atmospheric pollution parameters. Chemical compositions of corrosion products were found to depend on environments and duration of exposure. In all environments, cuprite was the predominating corrosion product that formed first and continuously increased during the exposure. Among the sulphur-containing corrosion products, posnjakite and brochantite were more frequently found and the first formed earlier. Nantokite was the most common chlorine-containing products for most cases, except the high-chloride environment, where atacamite was detected instead. The corrosion rate of copper was well indicated by the colour of patina. The red-purple colour corresponded to the high corrosion rate and the greenish grey colour corresponded to the low corrosion rate. Corrosion rate of sheltered copper in urban-marine environment increased with the exposure time

Evaluation of the problematic of corrosion in bottoms of tanks of crude oil storage; Evaluacion de la problematica de corrosion en fondos de tanques de almacenamiento de petroleo crudo

Energy Technology Data Exchange (ETDEWEB)

Malo T, Jose M; Uruchurtu C, Jorge; Meza, Beatriz [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); Lopez C, Luis F [Region Marina Suroeste, Pemex (Mexico)

2003-07-01

resultados relacionados con la agresividad corrosiva de los fluidos de agua de crudo de la Terminal Maritima de Dos Bocas (TMDB), sobre la efectividad de los metodos de control anticorrosivo y sobre medidas de control que podrian adoptarse. Asimismo, este articulo forma parte de un trabajo realizado por personal del Instituto de Investigaciones Electricas (IIE) durante el ano 2002. La corrosion en tanques es de naturaleza electroquimica y tiene su origen en la fase acuosa que acompana al crudo al ser extraido del subsuelo. En el caso de los tanques de almacenamiento, la fase acuosa se separa en el fondo, ocasionado el mojado de las placas de acero del fondo y su degradacion. Debido al limitado acceso al interior del tanque durante su operacion, se diseno un dispositivo de pruebas que fue conectado a una valvula de drenado de un tanque de la terminal. El trabajo experimental busco evaluar la agresividad de los fluidos, el tipo de productos de corrosion formados y la eficacia de la proteccion catodica y de los recubrimientos. Adicionalmente, se recolectaron muestras de fluidos para analizar el nivel de agresividad natural que presenta el agua de los tres tipos de crudos: Maya, Olmeca e Istmo, manejados en la terminal, estudiando muestras de acero y de fluidos de planta bajo condiciones controladas de laboratorio. La agresividad se obtuvo de mediciones de velocidades de reaccion de corrosion y de analisis de actividad microbiana. Se analizo la factibilidad de aplicar el metodo de proteccion catodica, observando su efectividad, asi como formas particulares de corrosion como la que ocurre en los pontones. Los resultados del estudio conducen a proponer un esquema de monitoreo para el seguimiento de la integridad de los recubrimientos, la operacion de la proteccion catodica y la corrosion en tanques, con el que se podria tener un mejor control de la operacion de los metodos anticorrosivos y de la degradacion que ocurre por corrosion.

Effect of Flow Velocity on Corrosion Rate and Corrosion Protection Current of Marine Material

Energy Technology Data Exchange (ETDEWEB)

Lee, Seong Jong [Kunsan National University, Kunsan (Korea, Republic of); Han, Min Su; Jang, Seok Ki; Kim, Seong Jong [Mokpo National Maritime University, Mokpo (Korea, Republic of)

2015-10-15

In spite of highly advanced paint coating techniques, corrosion damage of marine metal and alloys increase more and more due to inherent micro-cracks and porosities in coatings formed during the coating process. Furthermore, flowing seawater conditions promote the breakdown of the protective oxide of the materials introducing more oxygen into marine environments, leading to the acceleration of corrosion. Various corrosion protection methods are available to prevent steel from marine corrosion. Cathodic protection is one of the useful corrosion protection methods by which the potential of the corroded metal is intentionally lowered to an immune state having the advantage of providing additional protection barriers to steel exposed to aqueous corrosion or soil corrosion, in addition to the coating. In the present investigation, the effect of flow velocity was examined for the determination of the optimum corrosion protection current density in cathodic protection as well as the corrosion rate of the steel. It is demonstrated from the result that the material corrosion under dynamic flowing conditions seems more prone to corrosion than under static conditions.

EFECTO DE LOS PARÁMETROS GEOMECÁNICOS EN EL FRACTURAMIENTO HIDRÁULICO DE YACIMIENTOS DE HIDROCARBUROS SENSIBLES A ESFUERZOS

OpenAIRE

NARANJO A., ABEL; SOTO J., CARLOS M.

2007-01-01

La teoría sobre el proceso de fracturamiento hidráulico indica que se requiere acoplar el comportamiento de la roca y el comportamiento del fluido para un modelamiento exitoso del tratamiento. En el presente trabajo se analizan los efectos de las propiedades geomecánicas en el fracturamiento hidráulico para yacimientos de hidrocarburos sensibles a esfuerzos. Se desarrolla un software para simular el fracturamiento hidráulico en tres dimensiones en diferencias finitas, que acopla el flujo de f...

NASA's Beachside Corrosion Test Site and Current Environmentally Friendly Corrosion Control Initiatives

Science.gov (United States)

Russell, Richard W.; Calle, Luz Marina; Johnston, Frederick; Montgomery, Eliza L.; Curran, Jerome P.; Kolody, Mark R.

2013-01-01

NASA began corrosion studies at the Kennedy Space Center (KSC) in 1966 during the Gemini/Apollo Programs with the evaluation of long-term corrosion protective coatings for carbon steel. KSC's Beachside Corrosion Test Site (BCTS), which has been documented by the American Society of Materials (ASM) as one of the most corrosive, naturally occurring, environments in the world, was established at that time. With the introduction of the Space Shuttle in 1981, the already highly corrosive conditions at the launch pad were rendered even more severe by the acid ic exhaust from the solid rocket boosters. In the years that followed, numerous studies have identified materials, coatings, and maintenance procedures for launch hardware and equipment exposed to the highly corrosive environment at the launch pad. This paper presents a historical overview of over 45 years of corrosion and coating evaluation studies and a description of the BCTS's current capabilities. Additionally, current research and testing programs involving chromium free coatings, environmentally friendly corrosion preventative compounds, and alternates to nitric acid passivation will be discussed.

NASA's Corrosion Technology Laboratory at the Kennedy Space Center: Anticipating, Managing, and Preventing Corrosion

Science.gov (United States)

Calle, Luz Marina

2015-01-01

The marine environment at NASAs Kennedy Space Center (KSC) has been documented by ASM International (formerly American Society for Metals) as the most corrosive in North America. With the introduction of the Space Shuttle in 1981, the already highly corrosive conditions at the launch pads were rendered even more severe by the highly corrosive hydrochloric acid (HCl) generated by the solid rocket boosters (SRBs). Numerous failures at the launch pads are caused by corrosion. The structural integrity of ground infrastructure and flight hardware is critical to the success, safety, cost, and sustainability of space missions. NASA has over fifty years of experience dealing with unexpected failures caused by corrosion and has developed expertise in corrosion control in the launch and other environments. The Corrosion Technology Laboratory at KSC evolved, from what started as an atmospheric exposure test site near NASAs launch pads, into a capability that provides technical innovations and engineering services in all areas of corrosion for NASA, external partners, and customers.This paper provides a chronological overview of NASAs role in anticipating, managing, and preventing corrosion in highly corrosive environments. One important challenge in managing and preventing corrosion involves the detrimental impact on humans and the environment of what have been very effective corrosion control strategies. This challenge has motivated the development of new corrosion control technologies that are more effective and environmentally friendly. Strategies for improved corrosion protection and durability can have a huge impact on the economic sustainability of human spaceflight operations.

Fighting corrosion in India

Energy Technology Data Exchange (ETDEWEB)

Rajagopalan, K S; Rangaswamy, N S

1979-03-01

A survey covers the cost of corrosion in India; methods of preventing corrosion in industrial plants; some case histories, including the prevention of corrosion in pipes through which fuels are pumped to storage and the stress-corrosion cracking of evaporators in fertilizer plants; estimates of the increase in demand in 1979-89 for anticorrosion products and processes developed by the Central Electrochemical Research Institute (CECRI) at Karaikudi, India; industries that may face corrosion problems requiring assistance from CECRI, including the light and heavy engineering structural, and transport industries and the chemical industry; and some areas identified for major efforts, including the establishment of a Corrosion Advisory Board with regional centers and the expansion of the Tropical Corrosion Testing Station at Mandapam Camp, Tamil Nadu.

Corrosion evaluation technology

International Nuclear Information System (INIS)

Kim, Uh Chul; Han, Jeong Ho; Nho, Kye Ho; Lee, Eun Hee; Kim, Hong Pyo; Hwang, Seong Sik; Lee, Deok Hyun; Hur, Do Haeng; Kim, Kyung Mo.

1997-09-01

A multifrequency ACPD system was assembled which can measure very small crack. Stress corrosion cracking test system with SSRT operating high temperature was installed. Stress corrosion cracking test of newly developed alloy 600 and existing alloy 600 was carried out in steam atmosphere of 400 deg C. No crack was observed in both materials within a test period of 2,000 hrs. Corrosion fatigue test system operating at high temperature was installed in which fatigue crack was measured by CDPD. Lead enhanced the SCC of the Alloy 600 in high temperature water, had a tendency to modify a cracking morphology from intergranular to transgranular. Pit initiation preferentially occurred at Ti-rich carbide. Resistance to pit initiation decreased with increasing temperature up to 300 deg C. Test loop for erosion corrosion was designed and fabricated. Thin layer activation technique was very effective in measuring erosion corrosion. Erosion corrosion of a part of secondary side pipe was evaluated by the Check Family Codes of EPRI. Calculated values of pipe thickness by Check Family Codes coincided with the pipe thickness measured by UT with an error of ± 20%. Literature review on turbine failure showed that failure usually occurred in low pressure turbine rotor disc and causes of failure are stress corrosion cracking and corrosion fatigue. (author). 12 refs., 20 tabs., 77 figs

Corrosion Cost and Corrosion Map of Korea - Based on the Data from 2005 to 2010

International Nuclear Information System (INIS)

Kim, Y. S.; Lim, H. K.; Kim, J. J.; Hwang, W. S.; Park, Y. S.

2011-01-01

Corrosion of metallic materials occurs by the reaction with corrosive environment such as atmosphere, marine, soil, urban, high temperature etc. In general, reduction of thickness and cracking and degradation are resulted from corrosion. Corrosion in all industrial facilities and infrastructure causes large economic losses as well as a large number of accidents. Economic loss by corrosion has been reported to be nearly 1-6% of GNP or GDP. In order to reduce corrosion damage of industrial facilities, corrosion map as well as a systematic investigation of the loss of corrosion in each industrial sector is needed. The Corrosion Science Society of Korea in collaboration with 15 universities and institutes has started to survey on the cost of corrosion and corrosion map of Korea since 2005. This work presents the results of the survey on cost of corrosion by Uhlig, Hoar, and input-output methods, and the evaluation of atmospheric corrosion rate of carbon steel, weathering steel, galvanized steel, copper, and aluminum in Korea. The total corrosion cost was estimated in terms of the percentage of the GDP of industry sectors and the total GDP of Korea. According to the result of Input/output method, corrosion cost of Korea was calculated as 2.9% to GDP (2005). Time of wetness was shown to be categories 3 to 4 in all exposure areas. A definite seasonal difference was observed in Korea. In summer and fall, time of wetness was higher than in other seasons. Because of short exposure period (12 months), significant corrosion trends depending upon materials and exposure corrosion environments were not revealed even though increased mass loss and decreased corrosion rate by exposure time

Exploratory shaft liner corrosion estimate

International Nuclear Information System (INIS)

Duncan, D.R.

1985-10-01

An estimate of expected corrosion degradation during the 100-year design life of the Exploratory Shaft (ES) is presented. The basis for the estimate is a brief literature survey of corrosion data, in addition to data taken by the Basalt Waste Isolation Project. The scope of the study is expected corrosion environment of the ES, the corrosion modes of general corrosion, pitting and crevice corrosion, dissimilar metal corrosion, and environmentally assisted cracking. The expected internal and external environment of the shaft liner is described in detail and estimated effects of each corrosion mode are given. The maximum amount of general corrosion degradation was estimated to be 70 mils at the exterior and 48 mils at the interior, at the shaft bottom. Corrosion at welds or mechanical joints could be significant, dependent on design. After a final determination of corrosion allowance has been established by the project it will be added to the design criteria. 10 refs., 6 figs., 5 tabs

Dictionary corrosion and corrosion control. English-German/German-English. Fachwoerterbuch Korrosion und Korrosionsschutz. Englisch-Deutsch/Deutsch-Englisch

Energy Technology Data Exchange (ETDEWEB)

1985-01-01

This dictionary has 13000 entries in both languages. Keywords and extensive accompanying information simplify the choice of word for the user. The following topics are covered: Theoretical principles of corrosion; Corrosion of the metals and alloys most frequently used in engineering. Types of corrosion - (chemical-, electro-chemical, biological corrosion); forms of corrosion (superficial, pitting, selective, intercrystalline and stress corrosion; vibrational corrosion cracking); erosion and cavitation. Methods of corrosion control (material selection, temporary corrosion protection media, paint and plastics coatings, electro-chemical coatings, corrosion prevention by treatment of the corrosive media); Corrosion testing methods.

Factores nutricionales maternos y el bajo peso al nacer en un área de salud

Directory of Open Access Journals (Sweden)

Arley Rey Vilchez

2013-01-01

Full Text Available Fundamento: el bajo peso al nacer es multifactorial y se atribuye a causas maternas, fetales y ambientales. Los hábitos alimentarios inadecuados unidos a otros factores nutricionales maternos son determinantes. Objetivo: identificar los factores nutricionales maternos relacionados con el bajo peso al nacer en pacientes del Área I del municipio Cienfuegos. Métodos: se realizó un estudio analítico, retrospectivo, de casos y controles entre enero 2006 y diciembre 2008. Se estudiaron 50 madres de recién nacidos bajo peso (casos y 100 madres de niños normopesos (controles a razón de 2 por cada caso, seleccionadas del registro de nacimientos del área. Se revisaron las historias clínicas obstétricas y se entrevistó a cada paciente para evaluar sus hábitos alimentarios según frecuencia de comidas y grupos de alimentos consumidos. El procesamiento de la información se realizó utilizando el programa estadístico SPSS versión 15,0. Los resultados se presentaron en tablas con frecuencias absolutas, porcentajes y resultados de las técnicas estadísticas empleadas. Resultados: se comportaron como factores de riesgo: la edad materna, el estado nutricional al inicio del embarazo, la ganancia de peso durante la gestación y la hemoglobina del tercer trimestre. Las mujeres con hábitos alimentarios inestables e insuficientes tuvieron 33 veces más probabilidades de tener neonatos bajo peso y las que refirieron dietas no saludables según grupos de alimentos consumidos tuvieron 9 veces más riesgo. Conclusiones: los factores nutricionales maternos influyeron en la incidencia del bajo peso al nacer, fundamentalmente los hábitos alimentarios inadecuados.

Penetration of corrosion products and corrosion-induced cracking in reinforced cementitious materials

DEFF Research Database (Denmark)

Michel, Alexander; Pease, Brad J.; Peterova, Adela

2014-01-01

This paper describes experimental investigations on corrosion-induced deterioration in reinforced cementitious materials and the subsequent development and implementation of a novel conceptual model. Rejnforced mortar specimens of varying water-to-cement ratios were subjected to current-induced c......This paper describes experimental investigations on corrosion-induced deterioration in reinforced cementitious materials and the subsequent development and implementation of a novel conceptual model. Rejnforced mortar specimens of varying water-to-cement ratios were subjected to current......-dependent concentrations of corrosion products averaged through the specimen thickness. Digital image correlation (DIC) was used to measure corrosion-induced deformations including deformations between steel and cementitious matrix as well as formation and propagation of corrosion-induced cracks. Based on experimental...... observations, a conceptual model was developed to describe the penetration of solid corrosion products into capillary pores of the cementitious matrix. Only capillary pores within a corrosion accommodating region (CAR), i.e. in close proximity of the steel reinforcement, were considered accessible...

Los exilios de católicos y arrianos bajo Leovigildo y Recaredo

Directory of Open Access Journals (Sweden)

Vallejo Girvés, Margarita

2003-06-01

Full Text Available In this paper we try to analyse the various topics of the exile that have been applied by the visigothic kings Leovigild and Reccared. It is known that most part of the individuals that had suffered this exile were ecclesiasticals, catholics under Leovigild and arians during Reccared, but all of them were of germanic origin.

En este artículo se analizan los diversos tipos de exilio que aplicaron los monarcas visigodos Leovigildo y Recaredo. Se da la circunstancia de que la mayoría de ellos fueron eclesiásticos y que bajo Leovigildo lo sufrieron singularmente los católicos y los arríanos bajo Recaredo, pero en ambos casos todos los condenados son de origen germánico.

NASA's Corrosion Technology Laboratory at the Kennedy Space Center: Anticipating, Managing, and Preventing Corrosion

Science.gov (United States)

Calle, Luz Marina

2014-01-01

Corrosion is the degradation of a material that results from its interaction with the environment. The marine environment at NASAs Kennedy Space Center (KSC) has been documented by ASM International (formerly American Society for Metals) as the most corrosive in the United States. With the introduction of the Space Shuttle in 1981, the already highly corrosive conditions at the launch pads were rendered even more severe by the 70 tons of highly corrosive hydrochloric acid that were generated by the solid rocket boosters. Numerous failures at the launch pads are caused by corrosion.The structural integrity of ground infrastructure and flight hardware is critical to the success, safety, cost, and sustainability of space missions. As a result of fifty years of experience with launch and ground operations in a natural marine environment that is highly corrosive, NASAs Corrosion Technology Laboratory at KSC is a major source of corrosion control expertise in the launch and other environments. Throughout its history, the Laboratory has evolved from what started as an atmospheric exposure facility near NASAs launch pads into a world-wide recognized capability that provides technical innovations and engineering services in all areas of corrosion for NASA and external customers.This presentation will provide a historical overview of the role of NASAs Corrosion Technology in anticipating, managing, and preventing corrosion. One important challenge in managing and preventing corrosion involves the detrimental impact on humans and the environment of what have been very effective corrosion control strategies. This challenge has motivated the development of new corrosion control technologies that are more effective and environmentally friendly. Strategies for improved corrosion protection and durability can have a huge impact on the economic sustainability of human spaceflight operations.

Corrosion behavior of corrosion resistant alloys in stimulation acids

Energy Technology Data Exchange (ETDEWEB)

Cheldi, Tiziana [ENI E and P Division, 20097 San Donato Milanese Milano (Italy); Piccolo, Eugenio Lo; Scoppio, Lucrezia [Centro Sviluppo Materiali, via Castel Romano 100, 00128 Rome (Italy)

2004-07-01

In the oil and gas industry, selection of CRAs for downhole tubulars is generally based on resistance to corrosive species in the production environment containing CO{sub 2}, H{sub 2}S, chloride and in some case elemental sulphur. However, there are non-production environments to which these materials must also be resistant for either short term or prolonged duration; these environments include stimulation acids, brine and completion fluids. This paper reports the main results of a laboratory study performed to evaluate the corrosion and stress corrosion behaviour to the acidizing treatments of the most used CRAs for production tubing and casing. Laboratory tests were performed to simulate both 'active' and 'spent' acids operative phases, selecting various environmental conditions. The selected steel pipes were a low alloyed steel, martensitic, super-martensitic, duplex 22 Cr, superduplex 25 Cr and super-austenitic stainless steels (25 Cr 35 Ni). Results obtained in the 'active' acid environments over the temperature range of 100-140 deg. C, showed that the blend acids with HCl at high concentration and HCl + HF represented too much severe conditions, where preventing high general corrosion and heavy localised corrosion by inhibition package becomes very difficult, especially for duplex steel pipe, where, in some case, the specimens were completely dissolved into the solution. On the contrary, all steels pipes were successfully protected by inhibitor when organic acid solution (HCOOH + CH{sub 3}COOH) were used. Furthermore, different effectiveness on corrosion protection was showed by the tested inhibitors packages: e.g. in the 90% HCl at 12% + 10 CH{sub 3}COOH acid blend. In 'spent' acid environments, all steel pipes showed to be less susceptible to the localised and general corrosion attack. Moreover, no Sulphide Stress Corrosion Cracking (SSC) was observed. Only one super-austenitic stainless steel U-bend specimen showed

Corrosion failure analysis as related to prevention of corrosion failures

International Nuclear Information System (INIS)

Suss, H.

1977-10-01

The factors and conditions which have contributed to many of the corrosion related service failures are discussed based on a review of actual case histories. The anti-corrosion devices which developed as a result of these failure analyses are reviewed, and the method which must be adopted and used to take advantage of the available corrosion prevention techniques is discussed

Corrosion and corrosion fatigue of airframe aluminum alloys

Science.gov (United States)

Chen, G. S.; Gao, M.; Harlow, D. G.; Wei, R. P.

1994-01-01

Localized corrosion and corrosion fatigue crack nucleation and growth are recognized as degradation mechanisms that effect the durability and integrity of commercial transport aircraft. Mechanically based understanding is needed to aid the development of effective methodologies for assessing durability and integrity of airframe components. As a part of the methodology development, experiments on pitting corrosion, and on corrosion fatigue crack nucleation and early growth from these pits were conducted. Pitting was found to be associated with constituent particles in the alloys and pit growth often involved coalescence of individual particle-nucleated pits, both laterally and in depth. Fatigue cracks typically nucleated from one of the larger pits that formed by a cluster of particles. The size of pit at which fatigue crack nucleates is a function of stress level and fatigue loading frequency. The experimental results are summarized, and their implications on service performance and life prediction are discussed.

Atmospheric corrosion of uranium-carbon alloys; Corrosion atmospherique des alliages uranium-carbone

Energy Technology Data Exchange (ETDEWEB)

Rousset, P; Accary, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1965-07-01

The authors study the corrosion of uranium-carbon alloys having compositions close to that of the mono-carbide; they show that the extent of the observed corrosion effects increases with the water vapour content of the surrounding gas and they conclude that the atmospheric corrosion of these alloys is due essentially to the humidity of the air, the effect of the oxygen being very slight at room temperature. They show that the optimum conditions for preserving U-C alloys are either a vacuum or a perfectly dry argon atmosphere. The authors have also established that the type of corrosion involved is a corrosion which 'cracks under stress' and is transgranular (it can also be intergranular in the case of sub-stoichiometric alloys). They propose, finally, two hypotheses for explaining this mechanism, one of which is illustrated by the existence, at the fissure interface, of corrosion products which can play the role of 'corners' in the mono-carbide grains. (authors) [French] Les auteurs etudient la corrosion des alliages uranium-carbone de composition voisine du monocarbure; ils montrent que l'importance des effets de la corrosion observee augmente avec la teneur en vapeur d'eau du milieu gazeux ambiant et concluent que la corrosion atmospherique de ces alliages est due essentiellement a l'humidite de l'air, l'action de l'oxygene de l'air etant tres faible a la temperature ambiante. Ils indiquent que les conditions optimales de conservation des alliages U-C sont le vide ou une atmosphere d'argon parfaitement desseches. D'autre part, les auteurs etablissent que le type de corrosion mis en jeu est une corrosion 'fissurante sous contrainte', transgranulaire (pouvant egalement etre intergranulaire dans le cas d'alliages sous-stoechiometriques). Ils proposent enfin deux hypotheses pour rendre compte de ce mecanisme, dont l'une est illustree par la mise en evidence, a l'interface des fissures, de produits de corrosion pouvant jouer le role de 'coins' dans les grains de

Corrosion and corrosion protection of support structures for offshore wind energy devices (OWEA)

Energy Technology Data Exchange (ETDEWEB)

Momber, A. [Muehlhan AG, Schlinckstrasse 3, D-21107 Hamburg (Germany)

2011-05-15

The paper provides a review about the corrosion and corrosion protection of offshore wind energy devices (OWEA). Firstly, special features resulting from location and operation of OWEA are being discussed. Secondly, types of corrosion and corrosion phenomena are summarized in a systematic way. Finally, practical solutions to the corrosion protection of OWEA, including steel allowances, cathodic protection and coatings and linings, are discussed. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Corrosion behaviors and effects of corrosion products of plasma electrolytic oxidation coated AZ31 magnesium alloy under the salt spray corrosion test

Science.gov (United States)

Wang, Yan; Huang, Zhiquan; Yan, Qin; Liu, Chen; Liu, Peng; Zhang, Yi; Guo, Changhong; Jiang, Guirong; Shen, Dejiu

2016-08-01

The effects of corrosion products on corrosion behaviors of AZ31 magnesium alloy with a plasma electrolytic oxidation (PEO) coating were investigated under the salt spray corrosion test (SSCT). The surface morphology, cross-sectional microstructure, chemical and phase compositions of the PEO coating were determined using scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction analysis (XRD), respectively. Further, the corrosion process of the samples under the SSCT was examined in a non-aqueous electrolyte (methanol) using electrochemical impedance spectroscopy (EIS) coupled with equivalent circuit. The results show that the inner layer of the coating was destroyed firstly and the corrosion products have significant effects on the corrosion behaviors of the coating. The results above are discussed and an electrochemical corrosion model is proposed in the paper.

Limitación del esfuerzo terapéutico versus eutanasia: una reflexión bioética Limiting life-sustaining medical treatment versus euthanasia: a bioethical reflection

Directory of Open Access Journals (Sweden)

Gilberto de Jesús Betancourt Betancourt

2011-08-01

Full Text Available La práctica de la limitación del esfuerzo terapéutico no es novedad en las unidades de atención al paciente grave. Es necesario diferenciar la eutanasia de la limitación del esfuerzo terapéutico, considerada esta última como una buena práctica clínica. En este trabajo se realiza una reflexión teórica que tiene como objetivo fundamental el análisis bioético acerca de las diferencias fundamentales entre ambas.The practice of limiting life-sustaining medical treatment is nothing new at intensive care units. Euthanasia should be distinguished from limiting life-sustaining medical treatments, which is considered as a good practice. This paper presents a theoretical reflection based on a bioethical analysis of the main differences between both of them.

Long-term corrosion studies

International Nuclear Information System (INIS)

Gdowski, G.

1998-01-01

The scope of this activity is to assess the long-term corrosion properties of metallic materials under consideration for fabricating waste package containers. Three classes of metals are to be assessed: corrosion resistant, intermediate corrosion resistant, and corrosion allowance. Corrosion properties to be evaluated are general, pitting and crevice corrosion, stress-corrosion cracking, and galvanic corrosion. The performance of these materials will be investigated under conditions that are considered relevant to the potential emplacement site. Testing in four aqueous solutions, and vapor phases above them, and at two temperatures are planned for this activity. (The environmental conditions, test metals, and matrix are described in detail in Section 3.0.) The purpose and objective of this activity is to obtain the kinetic and mechanistic information on degradation of metallic alloys currently being considered for waste package containers. This information will be used to provide assistance to (1) waste package design (metal barrier selection) (E-20-90 to E-20-92), (2) waste package performance assessment activities (SIP-PA-2), (3) model development (E-20-75 to E-20-89). and (4) repository license application

Corrosion of beryllium

International Nuclear Information System (INIS)

Mueller, J.J.; Adolphson, D.R.

1987-01-01

The corrosion behavior of beryllium in aqueous and elevated-temperature oxidizing environments has been extensively studied for early-intended use of beryllium in nuclear reactors and in jet and rocket propulsion systems. Since that time, beryllium has been used as a structural material in les corrosive environments. Its primary applications include gyro systems, mirror and reentry vehicle structures, and aircraft brakes. Only a small amount of information has been published that is directly related to the evaluation of beryllium for service in the less severe or normal atmospheric environments associated with these applications. Despite the lack of published data on the corrosion of beryllium in atmospheric environments, much can be deduced about its corrosion behavior from studies of aqueous corrosion and the experiences of fabricators and users in applying, handling, processing, storing, and shipping beryllium components. The methods of corrosion protection implemented to resist water and high-temperature gaseous environments provide useful information on methods that can be applied to protect beryllium for service in future long-term structural applications

Initiation and inhibition of pitting corrosion on reinforcing steel under natural corrosion conditions

Energy Technology Data Exchange (ETDEWEB)

Abd El Wanees, S., E-mail: s_wanees@yahoo.com [Chemistry Department, Faculty of Science, University of Tabuk, Tabuk (Saudi Arabia); Chemistry Department, Faculty of Science, Zagazig University, Zagazig 44519 (Egypt); Bahgat Radwan, A. [Center for Advanced Materials, Qatar University, Doha 2713 (Qatar); Alsharif, M.A. [Chemistry Department, Faculty of Science, University of Tabuk, Tabuk (Saudi Arabia); Abd El Haleem, S.M. [Chemistry Department, Faculty of Science, Zagazig University, Zagazig 44519 (Egypt)

2017-04-01

Initiation and inhibition of pitting corrosion on reinforcing steel in saturated, naturally aerated Ca(OH){sub 2} solutions, under natural corrosion conditions, are followed through measurements of corrosion current, electrochemical impedance spectroscopy and SEM investigation. Induction period for pit initiation and limiting corrosion current for pit propagation are found to depend on aggressive salt anion and cation-types, as well as, concentration. Ammonium chlorides and sulfates are more corrosive than the corresponding sodium salts. Benzotriazole and two of its derivatives are found to be good inhibitors for pitting corrosion of reinforcing steel. Adsorption of these compounds follows a Langmuir adsorption isotherm. The thermodynamic functions ΔE{sup ∗}, ΔH{sup ∗} and ΔS{sup ∗} for pitting corrosion processes in the absence and presence of inhibitor are calculated and discussed. - Highlights: • Cl{sup −} and SO{sub 4} {sup 2-} induce pitting corrosion on passive reinforcing steel. • Initiation and propagation of pitting depend on cation and anion types. • Inhibition is based on adsorption according to Langmuir isotherm.

Real time corrosion monitoring in atmosphere using automated battery driven corrosion loggers

DEFF Research Database (Denmark)

Prosek, T.; Kouril, M.; Hilbert, Lisbeth Rischel

2008-01-01

diminishes due to corrosion. Zinc, iron, copper and nickel sensors at several thicknesses are available. Sensitivity of the corrosion measurement varies from 1 to 10 nm depending on the type and thickness of the sensor. Changes in the air corrosivity can be thus detected within hours or even tens of minutes......A logger enabling continuous measurement of corrosion rate of selected metals in indoor and outdoor atmospheres has been developed. Principle of the measurement method is based on the increasing electrical resistance of a measuring element made of the material concerned as its cross-sectional area....... The logger lifetime in medium corrosive environments is designed to be 2 years with full autonomy. Data on the sensor corrosion rate are available any time through GPRS connection or by a non-contact inductive reading without the need of retracting the logger from the exposure site....

Estudio de una Cronosecuencia de Suelos en el Bajo Cauca (Antioquia

Directory of Open Access Journals (Sweden)

Jaramillo J. Daniel F.

1996-09-01

Full Text Available En la región del Bajo Cauca, Antioquia, se estudiaron tres terrazas, a diferentes alturas, las cuales poseen diferencias apreciables entre la evolución de sus respectivos suelos. La terraza de mayor altura presentó los suelos más evolucionados: Typic Paleudult; la de mediana altura presentó suelos de incipiente evolución, clasificados como Typic Dystropept y la de menor altitud presentó suelos recientes, con muy bajo grado de evolución: Tropic Fluvaquent. Las diferencias en evolución observadas entre los suelos se deben a los largos intervalos de tiempo transcurridos entre la formación de los tres niveles de las terrazas. La fertilidad natural de los suelos desarrollados sobre las terrazas alta y media se puede calificar como baja a muy baja; por su parte, la terraza a menor altura posee alta fertilidad.

Corrosion-resistant metal surfaces

Science.gov (United States)

Sugama, Toshifumi [Wading River, NY

2009-03-24

The present invention relates to metal surfaces having thereon an ultrathin (e.g., less than ten nanometer thickness) corrosion-resistant film, thereby rendering the metal surfaces corrosion-resistant. The corrosion-resistant film includes an at least partially crosslinked amido-functionalized silanol component in combination with rare-earth metal oxide nanoparticles. The invention also relates to methods for producing such corrosion-resistant films.

Corrosion testing facilities in India

International Nuclear Information System (INIS)

Viswanathan, R.; Subramanian, Venu

1981-01-01

Major types of corrosion tests, establishment of specifications on corrosion testing and scope of their application in practice are briefly described. Important organizations in the world which publish specifications/standards are listed. Indian organizations which undertake corrosion testing and test facilities available at them are also listed. Finally in an appendix, a comprehensive list of specifications relevant to corrosion testing is given. It is arranged under the headings: environmental testing, humidity tests, salt spray/fog tests, immersion tests, specification corrosion phenomena, (tests) with respect to special corrosion media, (tests) with respect to specific corrosion prevention methods, and specific corrosion tests using electrical and electrochemical methods (principles). Each entry in the list furnishes information about: nature of the test, standard number, and its specific application. (M.G.B.)

Serie Madera para construcción La madera certificada bajo el concepto del triple resultado

OpenAIRE

Camacho-Cornejo, Diego; Moya-Roque, Róger

2012-01-01

A nivel mundial existe una tendencia de utilización de los productos certificados de madera bajo el concepto de triple resultado. En Costa Rica, diferentes empresas trabajan bajo este concepto. Es por ello que el presente trabajo tiene como objetivo mostrar el desarrollo de la madera certificada en Costa Rica, estableciendo la importancia de utilizar este tipo de madera, las ventajas de utilizarla en relación a aquella que no presenta esta certificación. Así mismo se presenta un detalle de la...

Corrosion characteristics of K-claddings

International Nuclear Information System (INIS)

Park, J. Y.; Choi, B. K.; Jung, Y. H.; Jung, Y. H.

2004-01-01

The Improvement of the corrosion resistance of nuclear fuel claddings is the critical issue for the successful development of the high burn-up fuel. KAERI have developed the K-claddings having a superior corrosion resistance by controlling the alloying element addition and optimizing the manufacturing process. The comparative evaluation of the corrosion resistance for K-claddings and the foreign claddings was performed and the effect of the heat treatment on the corrosion behavior of K-claddings was also examined. Corrosion tests were carried out in the conditions of 360 .deg. C pure water, PWR-simulating loop and 400 .deg. C steam, From the results of the corrosion tests, it was found that the corrosion resistance of K-claddings is superior to those of Zry4 and A claddings and K6 showed a better corrosion resistance than K3. The corrosion behavior of K-cladding was strongly influenced by the final annealing rather than the intermediate annealing, and the corrosion resistance increased with decreasing the final annealing temperature

Factores de riesgo en el bajo peso al nacer

Directory of Open Access Journals (Sweden)

Guillermo Díaz Alonso

1995-06-01

Full Text Available Se realizó un estudio retrospectivo de tipo caso control en el área del Policlínico Docente "Luis A. Turcios Lima" del municipio 10 de Octubre durante el período de 1990 a 1993, con el objetivo de identificar el comportamiento del bajo peso al nacer, establecer la existencia y la intensidad de esta entidad con los factores de riesgo seleccionados, e identificar el grado de influencia individual de dichos factores. La muestra quedó conformada por 92 recién nacidos de bajo peso y 468 con normopeso. Las variables estudiadas fueron la edad materna, la valoración ponderal, las complicaciones obstétricas, las enfermedades asociadas con la gestación, el hábito de fumar y el período intergenésico. Se aplicó el test chi-cuadrado, el odds- -ratio y el de riesgo atribuible en los nacimientos expuestos y en la población total. Todas las variables estuvieron asociadas significativamente con el bajo peso al nacer, y fueron identificadas como factores de riesgo con influencia marcada: la edad materna de 35 años o más, la amenaza de parto prematuro, la rotura prematura de membranas, la toxemia y la diabetes mellitus; con efecto moderado, el bajo peso materno, un período intergenésico menor de 1 año, la hipertensión arterial, el asma bronquial, el hábito de fumar, la sepsis urinaria, y con influencia ligera, la edad materna inferior a los 20 años.A case-control retrospective study was carried out at "Luis A. Turcios Lima" Teaching Polyclinics form 10 de Octubre municipality during the period of 1990-1993, with the aim of identifying the behaviour of low birth weight, establishing the occurrence and intensity of this entity with selected risk factors, and identifying the degree of individual influence of such factors. The sample consisted of 92 low birth weight infants and 468 with normal weight. Variables studied were: maternal age, weight appraisal, and obstetric complications, diseases associated with pregnancy, smoking habit, and the

Corrosion control. 2. ed.

International Nuclear Information System (INIS)

Bradford, S.A.

2001-01-01

The purpose of this text is to train engineers and technologists not just to understand corrosion but to control it. Materials selection, coatings, chemical inhibitors, cathodic and anodic protection, and equipment design are covered in separate chapters. High-temperature oxidation is discussed in the final two chapters ne on oxidation theory and one on controlling oxidation by alloying and with coatings. This book treats corrosion and high-temperature oxidation separately. Corrosion is divided into three groups: (1) chemical dissolution including uniform attack, (2) electrochemical corrosion from either metallurgical or environmental cells, and (3) stress-assisted corrosion. Corrosion is logically grouped according to mechanisms rather than arbitrarily separated into different types of corrosion as if they were unrelated. For those university students and industry personnel who approach corrosion theory very hesitantly, this text will present the electrochemical reactions responsible for corrosion summed up in only five simple half-cell reactions. When these are combined on a polarization diagram, which is also explained in detail, the electrochemical processes become obvious. For those who want a text stripped bare of electrochemical theory, several noted sections can be omitted without loss of continuity. However, the author has presented the material in such a manner that these sections are not beyond the abilities of any high school graduate who is interested in technology

Three-dimensional modeling of pavement with dual load using finite element

Directory of Open Access Journals (Sweden)

Wilson Rodríguez-Calderón

2015-01-01

Full Text Available El modelo desarrollado busca prede cir los esfuerzos y deformaci ones de un pavimento de manera más real, realizando un análisis elástico tridimensional con solicitaciones de carga de ejes dobles, cons tituyéndose en un avance respect o de modelos axisimétricos bidimensionales que s ólo representan el comportamiento bajo car gas de ejes sencillos. Etapas anteriores de esta investigación dan cuenta de modelos bidimensionales de carga simple bajo distintas hipót esis de liga entre capas y modelo s constitutivos no lineales, n o obstante, el propósito es avanzar en la met odología de análisis del estad o tensodeformacional ante cargas estándar. El modelo se implem entó en el programa Algor y se realizó una comparación con el programa multicapa de dist ribución libre Elsym5 . Los resultados advierten la existencia de concentraciones de esfuerzos de corte en la capa asfáltica que pueden ser causantes de fallas importantes que no son tenidas en cuenta en los tradicionale s métodos de diseño lo cual podría llevar a la posibilidad de revaluarlos.

Corrosion in the oil industry

Energy Technology Data Exchange (ETDEWEB)

Brondel, D [Sedco Forex, Montrouge (France); Edwards, R [Schlumberger Well Services, Columbus, OH (United States); Hayman, A [Etudes et Productions Schlumberger, Clamart (France); Hill, D [Schlumberger Dowell, Tulsa, OK (United States); Mehta, S [Schlumberger Dowell, St. Austell (United Kingdom); Semerad, T [Mobil Oil Indonesia, Inc., Sumatra (Indonesia)

1994-04-01

Corrosion costs the oil industry billions of dollars a year, a fact that makes the role of the corrosion engineer an increasingly important one. Attention is paid to how corrosion affects every aspect of exploration and production, from offshore rigs to casing. Also the role of corrosion agents such as drilling and production fluids is reviewed. Methods of control and techniques to monitor corrosion are discussed, along with an explanation of the chemical causes of corrosion. 21 figs., 32 refs.

Phytochemicals as Green Corrosion Inhibitors in Various Corrosive ...

African Journals Online (AJOL)

There is an intensive effort underway to develop new plant origin corrosion inhibitors for metal subjected to various environmental conditions. These efforts have been motivated by the desire to replace toxic inhibitors used for mitigation of corrosion of various metals and alloys in aqueous solutions. Plants represent a class ...

Monitoring Microbially Influenced Corrosion

DEFF Research Database (Denmark)

Hilbert, Lisbeth Rischel

and diffusional effects and unreliable corrosion rates, when biofilm and ferrous sulphide corrosion products cover the steel surface. Corrosion rates can be overestimated by a factor of 10 to 100 by electrochemical techniques. Weight loss coupons and ER are recommended as necessary basic monitoring techniques......Abstract Microbially influenced corrosion (MIC) of carbon steel may occur in media with microbiological activity of especially sulphate-reducing bacteria (SRB). The applicability and reliability of a number of corrosion monitoring techniques for monitoring MIC has been evaluated in experiments....... EIS might be used for detection of MIC as the appearance of very large capacitances can be attributed to the combined ferrous sulphide and biofilm formation. Capacitance correlates directly with sulphide concentration in sterile sulphide media. Keywords: Corrosion monitoring, carbon steel, MIC, SRB...

SRB seawater corrosion project

Science.gov (United States)

Bozack, M. J.

1991-01-01

The corrosion behavior of 2219 aluminum when exposed to seawater was characterized. Controlled corrosion experiments at three different temperatures (30, 60 and 100 C) and two different environments (seawater and 3.5 percent salt solution) were designed to elucidate the initial stages in the corrosion process. It was found that 2219 aluminum is an active catalytic surface for growth of Al2O3, NaCl, and MgO. Formation of Al2O3 is favored at lower temperatures, while MgO is favored at higher temperatures. Visible corrosion products are formed within 30 minutes after seawater exposure. Corrosion characteristics in 3.5 percent salt solution are different than corrosion in seawater. Techniques utilized were: (1) scanning electron microscopy, (2) energy dispersive x-ray spectroscopy, and (3) Auger electron spectroscopy.

Corrosion of circulating water pipings in thermal and nuclear power stations and corrosion prevention measures

International Nuclear Information System (INIS)

Hachiya, Minoru

1982-01-01

In the age of energy conservation at present, the power generation facilities have been examined from the viewpoint of performance, endurance and economy, and in particular, the prevention of the loss due to the corrosion of various facilities is one of most important problems. Since circulating water pipings are in contact with sea water and soil, the peculiar corrosion phenomena are brought about on their external and internal surfaces. Namely, the pitting corrosion due to the environment of soil quality difference, the defects of coating and the contact with reinforcing bars in concrete occurs on the external surface, and the overall corrosion due to the increase of flow velocity and the pitting corrosion due to the defects of coating, the contact with different kinds of metals and the gap in corrosion-resistant steel occur on the internal surface. As the measures for corrosion prevention, corrosion-preventive coating and electric corrosion prevention are applied. The principle, the potential and current density, the system, the design procedure and the examples of application of electric corrosion prevention are described. (Kako, I.)

Situación General de la Industria de la Construcción de Bajo Bordo

OpenAIRE

Chui, Alexander; Gamero, Magali; Cornejo, Karla; Rios, Vanessa; Valdivia, Maria Laura; Benzaquén de las Casas, Jorge

2016-01-01

Objetivo: Determinar las condiciones en que se encuentra la industria de construcción naval de bajo bordo en el Perú, relacionado con su contexto latinoamericano. Métodos: Se estableció un protocolo de actuación a base entrevistas, cuestionarios y recopilación de datos con el fin de conocer los principales indicadores de la dinámica funcional e industria de construcción naval de bajo bordo. Resultados: El Perú ha crecido notablemente en las últimas dos décadas como consecuencia de la apertura...

Mobile evaporator corrosion test results

International Nuclear Information System (INIS)

Rozeveld, A.; Chamberlain, D.B.

1997-05-01

Laboratory corrosion tests were conducted on eight candidates to select a durable and cost-effective alloy for use in mobile evaporators to process radioactive waste solutions. Based on an extensive literature survey of corrosion data, three stainless steel alloys (304L, 316L, AL-6XN), four nickel-based alloys (825, 625, 690, G-30), and titanium were selected for testing. The corrosion tests included vapor phase, liquid junction (interface), liquid immersion, and crevice corrosion tests on plain and welded samples of candidate materials. Tests were conducted at 80 degrees C for 45 days in two different test solutions: a nitric acid solution. to simulate evaporator conditions during the processing of the cesium ion-exchange eluant and a highly alkaline sodium hydroxide solution to simulate the composition of Tank 241-AW-101 during evaporation. All of the alloys exhibited excellent corrosion resistance in the alkaline test solution. Corrosion rates were very low and localized corrosion was not observed. Results from the nitric acid tests showed that only 316L stainless steel did not meet our performance criteria. The 316L welded interface and crevice specimens had rates of 22.2 mpy and 21.8 mpy, respectively, which exceeds the maximum corrosion rate of 20 mpy. The other welded samples had about the same corrosion resistance as the plain samples. None of the welded samples showed preferential weld or heat-affected zone (HAZ) attack. Vapor corrosion was negligible for all alloys. All of the alloys except 316L exhibited either open-quotes satisfactoryclose quotes (2-20 mpy) or open-quotes excellentclose quotes (<2 mpy) corrosion resistance as defined by National Association of Corrosion Engineers. However, many of the alloys experienced intergranular corrosion in the nitric acid test solution, which could indicate a susceptibility to stress corrosion cracking (SCC) in this environment

The corrosion and corrosion mechanical properties evaluation for the LBB concept in VVERs

Energy Technology Data Exchange (ETDEWEB)

Ruscak, M.; Chvatal, P.; Karnik, D.

1997-04-01

One of the conditions required for Leak Before Break application is the verification that the influence of corrosion environment on the material of the component can be neglected. Both the general corrosion and/or the initiation and, growth of corrosion-mechanical cracks must not cause the degradation. The primary piping in the VVER nuclear power plant is made from austenitic steels (VVER 440) and low alloy steels protected with the austenitic cladding (VVER 1000). Inspection of the base metal and heterogeneous weldments from the VVER 440 showed that the crack growth rates are below 10 m/s if a low oxygen level is kept in the primary environment. No intergranular cracking was observed in low and high oxygen water after any type of testing, with constant or periodic loading. In the framework of the LBB assessment of the VVER 1000, the corrosion and corrosion mechanical properties were also evaluated. The corrosion and corrosion mechanical testing was oriented predominantly to three types of tests: stress corrosion cracking tests corrosion fatigue tests evaluation of the resistance against corrosion damage. In this paper, the methods used for these tests are described and the materials are compared from the point of view of response on static and periodic mechanical stress on the low alloyed steel 10GN2WA and weld metal exposed in the primary circuit environment. The slow strain rate tests and static loading of both C-rings and CT specimens were performed in order to assess the stress corrosion cracking characteristics. Cyclic loading of CT specimens was done to evaluate the kinetics of the crack growth under periodical loading. Results are shown to illustrate the approaches used. The data obtained were evaluated also from the point of view of comparison of the influence of different structure on the stress corrosion cracking appearance. The results obtained for the base metal and weld metal of the piping are presented here.

An evaluation of corrosion resistant alloys by field corrosion test in Japanese refuse incineration plants

International Nuclear Information System (INIS)

Kawahara, Yuuzou; Nakamura, Masanori; Shibuya, Eiichi; Yukawa, Kenichi

1995-01-01

As the first step for development of the corrosion resistant superheater tube materials of 500 C, 100 ata used in high efficient waste-to-energy plants, field corrosion tests of six conventional alloys were carried out at metal temperatures of 450 C and 550 C for 700 and 3,000 hours in four typical Japanese waste incineration plants. The test results indicate that austenitic alloys containing approximately 80 wt% [Cr+Ni] show excellent corrosion resistance. When the corrosive environment is severe, intergranular corrosion of 40∼200 microm depth occurs in stainless steel and high alloyed materials. It is confirmed quantitatively that corrosion behavior is influenced by environmental corrosion factors such as Cl concentration and thickness of deposits on tube surface, metal temperature, and flue gas temperature. The excellent corrosion resistance of high [Cr+Ni+Mo] alloys such as Alloy 625 is explained by the stability of its protective oxide, such that the time dependence of corrosion nearly obeys the parabolic rate law

Modelling reinforcement corrosion in concrete

DEFF Research Database (Denmark)

Michel, Alexander; Geiker, Mette Rica; Stang, Henrik

2012-01-01

A physio-chemical model for the simulation of reinforcement corrosion in concrete struc-tures was developed. The model allows for simulation of initiation and subsequent propaga-tion of reinforcement corrosion. Corrosion is assumed to be initiated once a defined critical chloride threshold......, a numerical example is pre-sented, that illustrates the formation of corrosion cells as well as propagation of corrosion in a reinforced concrete structure....

Understanding corrosion via corrosion product characterization: II. Role of alloying elements in improving the corrosion resistance of Zn-Al-Mg coatings on steel

International Nuclear Information System (INIS)

Volovitch, P.; Vu, T.N.; Allely, C.; Abdel Aal, A.; Ogle, K.

2011-01-01

Highlights: → Origins of better corrosion resistance of ZnAlMg coatings than galvanized steel. → Comparative study of corrosion products formed on ZnAlMg, ZnMg and Zn coatings. → Modeling of dissolution and precipitation stages of corrosion. → At early stages Mg stabilizes protective zinc basic salts during dry-wet cycling. → At later stages Al dissolves at high pH forming protective layered double hydroxides. - Abstract: Corrosion products are identified on Zn, ZnMg and ZnAlMg coatings in cyclic corrosion tests with NaCl or Na 2 SO 4 containing atmospheres. For Mg-containing alloys the improved corrosion resistance is achieved by stabilization of protective simonkolleite and zinc hydroxysulfate. At later stages, the formation of layered double hydroxides (LDH) is observed for ZnAlMg. According to thermodynamic modeling, Mg 2+ ions bind the excess of carbonate or sulfate anions preventing the formation of soluble or less-protective products. A preferential dissolution of Zn and Mg at initial stages of corrosion is confirmed by in situ dissolution measurement. The physicochemical properties of different corrosion products are compared.

Modelling of Corrosion Cracks

DEFF Research Database (Denmark)

Thoft-Christensen, Palle

Modelling of corrosion cracking of reinforced concrete structures is complicated as a great number of uncertain factors are involved. To get a reliable modelling a physical and mechanical understanding of the process behind corrosion in needed.......Modelling of corrosion cracking of reinforced concrete structures is complicated as a great number of uncertain factors are involved. To get a reliable modelling a physical and mechanical understanding of the process behind corrosion in needed....

Exposure testing of fasteners in preservative treated wood: Gravimetric corrosion rates and corrosion product analyses

Energy Technology Data Exchange (ETDEWEB)

Zelinka, Samuel L., E-mail: szelinka@fs.fed.u [USDA Forest Products Laboratory, One Gifford Pinchot Drive, Madison, WI 53726 (United States); Sichel, Rebecca J. [College of Engineering, University of Wisconsin, Madison, WI 53706 (United States); Stone, Donald S. [Department of Materials Science and Engineering, College of Engineering, University of Wisconsin, Madison, WI 53706 (United States)

2010-12-15

Research highlights: {yields} The composition of the corrosion products was similar for the nail head and shank. {yields} Reduced copper was not detected on any of the fasteners. {yields} Measured corrosion rates were between 1 and 35 {mu}m year{sup -1}. - Abstract: Research was conducted to determine the corrosion rates of metals in preservative treated wood and also understand the mechanism of metal corrosion in treated wood. Steel and hot-dip galvanized steel fasteners were embedded in wood treated with one of six preservative treatments and exposed to 27 {sup o}C at 100% relative humidity for 1 year. The corrosion rate was determined gravimetrically and the corrosion products were analyzed with scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction. Although the accepted mechanism of corrosion in treated wood involves the reduction of cupric ions from the wood preservative, no reduced copper was found on the corrosion surfaces. The galvanized corrosion products contained sulfates, whereas the steel corrosion products consisted of iron oxides and hydroxides. The possible implications and limitations of this research on fasteners used in building applications are discussed.

Habilidades pre-escolares de los niños nacidos prematuramente y con bajo peso

OpenAIRE

Sasha A. Martínez-Espiet; Irene Sumaza Laborde; Leila Crespo Fernández; Maribel Campos Rivera; Frances Boulon Díaz

2016-01-01

RESUMEN: El objetivo de este estudio fue conocer el nivel de desarrollo en la etapa pre-escolar de un grupo de niños nacidos prematuramente y con bajo peso. Se evaluó un grupo 20 niños de cuatro años nacidos prematuramente y con bajo peso y un grupo de 20 niños nacidos luego de gestación completada y peso deseado utilizando la prueba de integración visual-motora Beery-Buktenica. Además, se administró el cuestionario del desarrollo Ages and Stages (ASQ-3) a las 40 madres. El análisis estadísti...

Management of Reinforcement Corrosion

DEFF Research Database (Denmark)

Küter, André; Geiker, Mette Rica; Møller, Per

Reinforcement corrosion is the most important cause for deterioration of reinforced concrete structures, both with regard to costs and consequences. Thermodynamically consistent descriptions of corrosion mechanisms are expected to allow the development of innovative concepts for the management...... of reinforcement corrosion....

Viviendas de muy bajo coste

Directory of Open Access Journals (Sweden)

Lemus, V.

1982-11-01

Full Text Available Not available.En el Instituto de Investigaciones en Materiales de la Universidad Nacional Autónoma de México, se está desarrollando un área de investigación sobre tecnología de materiales y tecnología de sistemas constructivos, la cual está integrada por diversos proyectos encaminados a solucionar problemas relativos a la vivienda. El presente trabajo consiste en el desarrollo de materiales compuestos a base de desechos agrícolas e industriales, con características tales como baja densidad, resistencia adecuada, excelentes propiedades térmicas y acústicas y, fundamentalmente, bajo costo y gran disponibilidad. Los resultados obtenidos son bastante alentadores debido a la durabilidad y resistencia mecánica obtenidos a base del tratamiento proporcionado a la materia orgánica. Se comentan las aplicaciones actuales y futuras de estos nuevos materiales.

Microbiologically induced corrosion

International Nuclear Information System (INIS)

Stein, A.A.

1988-01-01

Biological attack is a problem that can affect all metallic materials in a variety of environments and systems. In the power industry, corrosion studies have focused on condensers and service water systems where slime, barnacles, clams, and other macro-organisms are easily detected. Efforts have been made to eliminate the effect of these organisms through the use of chlorination, backflushing, organic coating, or thermal shock. The objective is to maintain component performance by eliminating biofouling and reducing metallic corrosion. Recently, corrosion of power plant components by micro-organisms (bacteria) has been identified even in very clean systems. A system's first exposure to microbiologically induced corrosion (MIC) occurs during its first exposure to an aqueous environment, such as during hydrotest or wet layup. Corrosion of buried pipelines by sulfate-reducing bacteria has been studied by the petrochemical industry for years. This paper discusses various methods of diagnosing, monitoring, and controlling MIC in a variety of systems, as well as indicates areas where further study is needed

CORROSION RATE OF STEELS DX51D AND S220GD IN DIFFERENT CORROSION ENVIRONMENT

Directory of Open Access Journals (Sweden)

Alina Crina CIUBOTARIU

2016-06-01

Full Text Available Corrosion in the marine environment is an important issue because the costs causes by marine corrosion increased year upon year. It is necessary a correctly approach to materials selection, protection and corrosion control to reduce this burden of wasted materials, wasted energy and wasted money. Many different types of corrosion attack can be observed to structures, ships and other equipment used in sea water service. Shipping containers are exposed to various corrosive mediums like as airborne salt, industrial pollutants, rain and saltwater. Transport damage during loading onto and unloading off trucks, train beds and ships breaches the paint coating which further contributes to corrosion. The result is shortened container life and high costs for container repair or replacement. The paper intends to evaluate, by gravimetric method, the corrosion rate and corrosion penetration rate of two types of carbon steel DX51D and S220GD. Carbon steel DX51D and hot-dip galvanized steel S220GD are used in marine and industrial applications for buildings cargo vessels, container ships and oil tankers. For testing it was used different corrosive environments: 5% NaOH solution; 5% HCL solution and 0.5M NaCl solution. The samples were immersed in 400mL of testing solution for exposure period of 28 days. Periodically at 3 days, 7 days, 14 days, 21 days and 28 days was measured de mass loss and evaluate the corrosion rate and corrosion stability coefficient. The steel DX51D was stable in 5% NaOH solution for 28 days, the values of corrosion stability coefficient was 7 after 3 days and 6 after 28 days of immersion in corrosive medium. In 5% HCL solution steels DX51D and S220GD was completely corroded in 21 days with a corrosion stability coefficient equal with 9 for 7 days and 8 for 21 days of immersion in corrosive solution. It was observed a good resistance for 3 days in 0.5M NaCl solution with a corrosion stability coefficient equal with 5, but after that

General Corrosion and Localized Corrosion of the Drip Shield

Energy Technology Data Exchange (ETDEWEB)

F. Hua

2004-09-16

The repository design includes a drip shield (BSC 2004 [DIRS 168489]) that provides protection for the waste package both as a barrier to seepage water contact and a physical barrier to potential rockfall. The purpose of the process-level models developed in this report is to model dry oxidation, general corrosion, and localized corrosion of the drip shield plate material, which is made of Ti Grade 7. This document is prepared according to ''Technical Work Plan For: Regulatory Integration Modeling and Analysis of the Waste Form and Waste Package'' (BSC 2004 [DIRS 171583]). The models developed in this report are used by the waste package degradation analyses for TSPA-LA and serve as a basis to determine the performance of the drip shield. The drip shield may suffer from other forms of failure such as the hydrogen induced cracking (HIC) or stress corrosion cracking (SCC), or both. Stress corrosion cracking of the drip shield material is discussed in ''Stress Corrosion Cracking of the Drip Shield, the Waste Package Outer Barrier, and the Stainless Steel Structural Material'' (BSC 2004 [DIRS 169985]). Hydrogen induced cracking of the drip shield material is discussed in ''Hydrogen Induced Cracking of Drip Shield'' (BSC 2004 [DIRS 169847]).

General Corrosion and Localized Corrosion of the Drip Shield

International Nuclear Information System (INIS)

F. Hua

2004-01-01

The repository design includes a drip shield (BSC 2004 [DIRS 168489]) that provides protection for the waste package both as a barrier to seepage water contact and a physical barrier to potential rockfall. The purpose of the process-level models developed in this report is to model dry oxidation, general corrosion, and localized corrosion of the drip shield plate material, which is made of Ti Grade 7. This document is prepared according to ''Technical Work Plan For: Regulatory Integration Modeling and Analysis of the Waste Form and Waste Package'' (BSC 2004 [DIRS 171583]). The models developed in this report are used by the waste package degradation analyses for TSPA-LA and serve as a basis to determine the performance of the drip shield. The drip shield may suffer from other forms of failure such as the hydrogen induced cracking (HIC) or stress corrosion cracking (SCC), or both. Stress corrosion cracking of the drip shield material is discussed in ''Stress Corrosion Cracking of the Drip Shield, the Waste Package Outer Barrier, and the Stainless Steel Structural Material'' (BSC 2004 [DIRS 169985]). Hydrogen induced cracking of the drip shield material is discussed in ''Hydrogen Induced Cracking of Drip Shield'' (BSC 2004 [DIRS 169847])

Algas epífitas de Bajo Pepito, Isla Mujeres, Quintana Roo, México

Directory of Open Access Journals (Sweden)

L.I Quan-Young

2006-06-01

Full Text Available Epiphytic algae from Bajo Pepito, Isla Mujeres, Quintana Roo, México. A total of 96 epiphytic algae species were identified from Bajo Pepito, Quintana Roo, México. 60.4% (58 belonged to the Rhodophyta, 19.79% (19 to the Phaeophyta, 16.6% (16 to the Chlorophyta and 3.1% (3 to the Cyanophyta; 49 species (50.5% were found only in one month, while Heterosiphonia crispella was found in all of the sampled months. That species provided the largest contribution to the biomass of epiphytes. During January we registered the greater biommass and richness of epiphytes species, coincidently with high values of host species cover and rainfall. Rev. Biol. Trop. 54(2: 317-328. Epub 2006 Jun 01.

Catastrophes caused by corrosion

OpenAIRE

PETROVIC ZORAN C.

2016-01-01

For many years, huge attention has been paid to the problem of corrosion damage and destruction of metallic materials. Experience shows that failures due to corrosion problems are very important, and statistics at the world level shows that the damage resulting from the effects of various forms of corrosion is substantial and that, for example, in industrialized countries it reaches 4-5% of national incomes. Significant funds are determined annually for the prevention and control of corrosion...

An overview of erosion corrosion models and reliability assessment for corrosion defects in piping system

International Nuclear Information System (INIS)

Srividya, A.; Suresh, H.N.; Verma, A.K.; Gopika, V.; Santosh

2006-01-01

Piping systems are part of passive structural elements in power plants. The analysis of the piping systems and their quantification in terms of failure probability is of utmost importance. The piping systems may fail due to various degradation mechanisms like thermal fatigue, erosion-corrosion, stress corrosion cracking and vibration fatigue. On examination of previous results, erosion corrosion was more prevalent and wall thinning is a time dependent phenomenon. The paper is intended to consolidate the work done by various investigators on erosion corrosion in estimating the erosion corrosion rate and reliability predictions. A comparison of various erosion corrosion models is made. The reliability predictions based on remaining strength of corroded pipelines by wall thinning is also attempted. Variables in the limit state functions are modelled using normal distributions and Reliability assessment is carried out using some of the existing failure pressure models. A steady state corrosion rate is assumed to estimate the corrosion defect and First Order Reliability Method (FORM) is used to find the probability of failure associated with corrosion defects over time using the software for Component Reliability evaluation (COMREL). (author)

Corrosion protection and control using nanomaterials

CERN Document Server

Cook, R

2012-01-01

This book covers the use of nanomaterials to prevent corrosion. The first section deals with the fundamentals of corrosion prevention using nanomaterials. Part two includes a series of case studies and applications of nanomaterials for corrosion control.$bCorrosion is an expensive and potentially dangerous problem in many industries. The potential application of different nanostructured materials in corrosion protection, prevention and control is a subject of increasing interest. Corrosion protection and control using nanomaterials explores the potential use of nanotechnology in corrosion control. The book is divided into two parts. Part one looks at the fundamentals of corrosion behaviour and the manufacture of nanocrystalline materials. Chapters discuss the impact of nanotechnology in reducing corrosion cost, and investigate the influence of various factors including thermodynamics, kinetics and grain size on the corrosion behaviour of nanocrystalline materials. There are also chapters on electrodeposition ...

Efectividad del proyecto de convergencia contable mexicano emprendido a partir de 2005: evidencia empírica (1997-2010

Directory of Open Access Journals (Sweden)

Sergio Demetrio Polo Jiménez

2015-01-01

Full Text Available El propósito de nuestro estudio es conocer si los esfuerzos llevados a cabo por el Consejo Mexicano de Normas de Información Financiera ha logrado reducir las diferencias en el cálculo de las cifras contables mexicanas y las calculadas bajo principios norteamericanos (US GAAP en el periodo 1997- 2010. Para alcanzar los objetivos planteados hemos analizado 230 Informes 20-F que corresponden a 27 empresas mexicanas listadas en la bolsa de valores de Nueva York. Los resultados obtenidos en la aplicación de los modelos de regresión lineal muestran la existencia de determinados factores que explican el grado de comparabilidad de las variables contables fundamentales obtenidas bajo principios mexicanos y estadounidenses.

Autoestima en adolescentes con bajo rendimiento escolar a través del psicodiagnóstico de Rorschach

Directory of Open Access Journals (Sweden)

Magally de Garrido-Lecca

1997-12-01

Full Text Available El objetivo fue determinar si existen diferencias en la autoestima de adolescentes con bajo rendimiento escolar comparados con los de un rendimiento promedio o superior. Los participantes fueron 60 adolescentes, entre 13 y 16 años, de ambos sexos, con un C.I. promedio o superior al promedio, de los cuales 30 presentaban un bajo rendimiento escolar  (grupo de estudio y 30 un buen rendimiento (grupo contraste. Se administró el WISCR para determinar el C.I. y el Rorschach según el SC de Exner para evaluar la autoestima. Los resultados mostraron que el Rorschach es adecuado para evaluar la autoestima. Asimismo existe una diferencia significativa en la autoestima de adolescentes con bajo rendimiento como resultado de sus déficits afectivos, en comparación con los de alto rendimiento.

Monitoring and modeling stress corrosion and corrosion fatigue damage in nuclear reactors

International Nuclear Information System (INIS)

Andresen, P.L.; Ford, F.P.; Solomon, H.D.; Taylor, D.F.

1990-01-01

Stress corrosion and corrosion fatigue are significant problems in many industries, causing economic penalties from decreased plant availability and component repair or replacement. In nuclear power reactors, environmental cracking occurs in a wide variety of components, including reactor piping and steam generator tubing, bolting materials and pressure vessels. Life assessment for these components is complicated by the belief that cracking is quite irreproducible. Indeed, for conditions which were once viewed as nominally similar, orders of magnitude variability in crack growth rates are observed for stress corrosion and corrosion fatigue of stainless steels and low-alloy steels in 288 degrees C water. This paper shows that design and life prediction approaches are destined to be overly conservative or to risk environmental failure if life is predicted by quantifying only the effects of mechanical parameters and/or simply ignoring or aggregating environmental and material variabilities. Examples include the Nuclear Regulatory Commission (NRC) disposition line for stress-corrosion cracking of stainless steel in boiling water reactor (BWR) water and the American Society of Mechanical Engineers' Section XI lines for corrosion fatigue

Recognition and Analysis of Corrosion Failure Mechanisms

Directory of Open Access Journals (Sweden)

Steven Suess

2006-02-01

Full Text Available Corrosion has a vast impact on the global and domestic economy, and currently incurs losses of nearly $300 billion annually to the U.S. economy alone. Because of the huge impact of corrosion, it is imperative to have a systematic approach to recognizing and mitigating corrosion problems as soon as possible after they become apparent. A proper failure analysis includes collection of pertinent background data and service history, followed by visual inspection, photographic documentation, material evaluation, data review and conclusion procurement. In analyzing corrosion failures, one must recognize the wide range of common corrosion mechanisms. The features of any corrosion failure give strong clues as to the most likely cause of the corrosion. This article details a proven approach to properly determining the root cause of a failure, and includes pictographic illustrations of the most common corrosion mechanisms, including general corrosion, pitting, galvanic corrosion, dealloying, crevice corrosion, microbiologically-influenced corrosion (MIC, corrosion fatigue, stress corrosion cracking (SCC, intergranular corrosion, fretting, erosion corrosion and hydrogen damage.

Corrosion of PWR steam generators

International Nuclear Information System (INIS)

Garnsey, R.

1979-01-01

Some designs of pressurized water reactor (PWR) steam generators have experienced a variety of corrosion problems which include stress corrosion cracking, tube thinning, pitting, fatigue, erosion-corrosion and support plate corrosion resulting in 'denting'. Large international research programmes have been mounted to investigate the phenomena. The operational experience is reviewed and mechanisms which have been proposed to explain the corrosion damage are presented. The implications for design development and for boiler and feedwater control are discussed. (author)

Archaeological analogs and corrosion; Analogues archeologiques et corrosion

Energy Technology Data Exchange (ETDEWEB)

David, D

2008-07-01

In the framework of the high level and long life radioactive wastes disposal deep underground, the ANDRA built a research program on the material corrosion. In particular they aim to design containers for a very long time storage. Laboratory experiments are in progress and can be completed by the analysis of metallic archaeological objects and their corrosion after hundred years. (A.L.B.)

The Corrosion Inhibition Characteristics of Sodium Nitrite Using an On-line Corrosion Rate Measurement System

International Nuclear Information System (INIS)

Park, Mal-Yong; Kang, Dae-Jin; Moon, Jeon-Soo

2015-01-01

An on-line corrosion rate measurement system was developed using a personal computer, a data acquisition board and program, and a 2-electrode corrosion probe. Reliability of the developed system was confirmed with through comparison test. With this system, the effect of sodium nitrite (NaNO 2 ) as a corrosion inhibitor were studied on iron and aluminum brass that were immersed in sodium chloride (NaCl) solution. Corrosion rate was measured based on the linear polarization resistance method. The corrosion rates of aluminum brass and iron in 1% NaCl solutions were measured to be 0.290 mm per year (mmpy) and 0.2134 mmpy, respectively. With the addition of 200 ppm of NO 2 - , the corrosion rates decreased to 0.0470 mmpy and 0.0254 mmpy. The addition of NO 2 - caused a decrease in corrosion rates of both aluminum brass and iron, yet the NO 2 - acted as a more effective corrosion inhibitor for iron. than aluminum brass

Corrosion Engineering.

Science.gov (United States)

White, Charles V.

A description is provided for a Corrosion and Corrosion Control course offered in the Continuing Engineering Education Program at the General Motors Institute (GMI). GMI is a small cooperative engineering school of approximately 2,000 students who alternate between six-week periods of academic study and six weeks of related work experience in…

Some observations on phosphate based corrosion inhibitors in preventing carbon steel corrosion

International Nuclear Information System (INIS)

Anupkumar, B.; Satpathy, K.K.

2000-01-01

Among the various types of phosphonic acid based inhibitors assayed, namely HEDP, ATMP and a commercial corrosion inhibitor (code named Betz), it was found that Betz has the maximum amount of organic phosphate followed by HEDP and ATMP. The corrosion rate studies show that Betz gives the highest inhibition efficiency followed by HEDP and ATMP. This shows that organic phosphate plays a significant role in corrosion protection. However, it was observed that due to synergestic effect, HEDP in the presence of Zn 2+ gave a better corrosion protection than Betz. The results are discussed in the light of available literature. (author)

Corrosion and alteration of materials from the nuclear industry; La Corrosion et l'alteration des materiaux du nucleaire

Energy Technology Data Exchange (ETDEWEB)

Beauvy, M.; Berthoud, G.; Defranceschi, M.; Ducros, G.; Feron, D.; Guerin, Y.; Latge, C.; Limoge, Y.; Madic, C.; Santarini, G.; Seiler, J.M.; Vernaz, E.; Richet, C.

2010-07-01

The control of the corrosion phenomenon is of prime importance for the nuclear industry. The efficiency and the safety of facilities can be affected by this phenomenon. The nuclear industry has to face corrosion for a large variety of materials submitted to various environments. Metallic corrosion operates in the hot and aqueous environment of water reactors which represent the most common reactor type in the world. Progresses made in the control of the corrosion of the different components of these reactors allow to improve their safety. Corrosion is present in the facilities of the back-end of the fuel cycle as well (corrosion in acid environment in fuel reprocessing plants, corrosion of waste containers in disposal and storage facilities, etc). The future nuclear systems will widen even more the range of materials to be studied and the situations in which they will be placed (corrosion by liquid metals or by helium impurities). Very often, corrosion looks like a patchwork of particular cases in its description. The encountered corrosion problems and their study are presented in this book according to chapters representing the main sectors of the nuclear industry and classified with respect to their phenomenology. This monograph illustrates the researches in progress and presents some results of particular importance obtained recently. Content: 1 - Introduction: context, stakes and goals; definition of corrosion; a complex science; corrosion in the nuclear industry; 2 - corrosion in water reactors - phenomenology, mechanisms, remedies: A - uniform corrosion: mechanisms, uniform corrosion of fuel cladding, in-situ measurement of generalized corrosion rate by electrochemical methods, uniform corrosion of nickel alloys, characterization of the passive layer and growth mechanisms, the PACTOLE code - an integrating tool, influence of water chemistry on corrosion and contamination, radiolysis impact on uniform corrosion; B - stress corrosion: stress corrosion cracking

Smart Coatings for Corrosion Protection

Science.gov (United States)

Calle, Luz Marina; Li, Wendy; Buhrow, Jerry W.; Johnsey, Marissa N.

2016-01-01

Nearly all metals and their alloys are subject to corrosion that causes them to lose their structural integrity or other critical functionality. It is essential to detect corrosion when it occurs, and preferably at its early stage, so that action can be taken to avoid structural damage or loss of function. Protective coatings are the most commonly used method of corrosion control. However, progressively stricter environmental regulations have resulted in the ban of many commercially available corrosion protective coatings due to the harmful effects of their solvents or corrosion inhibitors. This work concerns the development of a multifunctional, smart coating for the autonomous control of corrosion. This coating is being developed to have the inherent ability to detect the chemical changes associated with the onset of corrosion and respond autonomously to indicate it and control it.

Modelo matemático para la predicción del esfuerzo de corte en el mecanizado a alta velocidad

Directory of Open Access Journals (Sweden)

Harber, R. E.

2004-08-01

Full Text Available This paper presents cutting force-based models able to describe a high speed machining process. The model considers the cutting force as output variable, essential for the physical processes that are taking place in high speed machining. Moreover, this paper shows the mathematical development to derive the integral-differential equations, and the algorithms implemented in MATLAB to predict the cutting force in real time. MATLAB is a software tool for doing numerical computations with matrices and vectors. It can also display information graphically and includes many toolboxes for several research and applications areas. Two end mill shapes are considered (i.e., cylindrical and ball end mill for real-time implementation of the developed algorithms. The developed models are validated in slot milling operations. The results corroborate the importance of the cutting force variable for predicting tool wear in high speed machining operations. The developed models are the starting point for future work related with vibration analysis, process stability and dimensional surface finish in high speed machining processes.

Este trabajo presenta una primera aproximación a un modelo matemático que describe el proceso de mecanizado a alta velocidad. El modelo propuesto está sustentado en el esfuerzo de corte como variable de salida, representativa de los procesos físicos que tienen lugar durante el corte. El trabajo muestra el desarrollo matemático conducente a la obtención de las ecuaciones integro-diferenciales y los algoritmos, computacionalmente eficientes e implementados en MATLAB, para la predicción del esfuerzo de corte en el mecanizado a alta velocidad. MATLAB es un entorno de computación y desarrollo de aplicaciones, que permite realizar de forma eficiente cálculos con vectores y matrices. En el entorno, se incluyen facilidades para el análisis numérico, cálculo matricial, procesamiento de señales y visualización gráfica. En los

cultivadas bajo un gradiente de sombra

Directory of Open Access Journals (Sweden)

Marco V. Gutiérrez

2007-01-01

Full Text Available Se evaluó el crecimiento de 9 especies de palmas cultivadas bajo un gradiente de sombra producido por mallas de polipropileno negro de 40, 50, 60, 70 y 80% de sombra, más un tratamiento de malla aluminizada de 70%, y uno con plantas a pleno sol. Las especies evaluadas fueron Caryota mitis (cola de pez, Chamaedorea costaricana (pacaya, Chamaedorea tepejilote (tepejilote, Dypsis lutescens (areca, Licuala elegans (licuala, Phoenix roebelenii (fénix, Ptychosperma macarthurii (palma macarthur, Roystonea regia (palma real, y Veitchia merrillii (navideña. Se midió la altura de las plantas, la longitud de las hojas maduras, y el número de hojas cosechadas, durante 5 cosechas por 2 años. En general, la altura de las plantas y la longitud de las hojas fueron menores a 0-40% de sombra, se incrementaron a 50-70%, y decrecieron a 80%. C. mitis, C. tepejilote, L. elegans y P. macarthurii, se comportaron como especies obligadas de sombra y no sobrevivieron a pleno sol. C. costaricana y D. lutescens sobrevivieron a plena exposición solar, y su crecimiento alcanzó valores máximos a 50-60%. P. roebelenii, R. regia, y V. merrillii mostraron un crecimiento reducido a 0-40%, pero éste mejoró bajo los demás niveles de sombra a lo largo del gradiente. En general, 1-2 años es un periodo apropiado para el cultivo de palmas de crecimiento rápido (R. regia, Chamedorea spp., D. lutescens en casas de mallas. Palmas de lento crecimiento (L.elegans pueden permanecer 3-5 años en una casa de sombra. Se discute estrategias para el uso de gradientes de sombra en el tiempo y en el espacio, según la utilidad y los requerimientos de las especies, los requisitos establecidos por el mercado, y el ciclo de producción del material vegetal.

Corrosion studies on PREPP waste form

International Nuclear Information System (INIS)

Welch, J.M.; Neilson, R.M. Jr.

1984-05-01

Deformation or Failure Test and Accelerated Corrosion Test procedures were conducted to investigate the effect of formulation variables on the corrosion of oversize waste in Process Experimental Pilot Plant (PREPP) concrete waste forms. The Deformation or Failure Test did not indicate substantial waste form swelling from corrosion. The presence or absence of corrosion inhibitor was the most significant factor relative to measured half-cell potentials identified in the Accelerated Corrosion Test. However, corrosion inhibitor was determined to be only marginally beneficial. While this study produced no evidence that corrosion is of sufficient magnitude to produce serious degradation of PREPP waste forms, the need for corrosion rate testing is suggested. 11 references, 4 figures, 8 tables

DPC materials and corrosion environments.

Energy Technology Data Exchange (ETDEWEB)

Ilgen, Anastasia Gennadyevna; Bryan, Charles R.; Teich-McGoldrick, Stephanie; Hardin, Ernest

2014-10-01

After an exposition of the materials used in DPCs and the factors controlling material corrosion in disposal environments, a survey is given of the corrosion rates, mechanisms, and products for commonly used stainless steels. Research needs are then identified for predicting stability of DPC materials in disposal environments. Stainless steel corrosion rates may be low enough to sustain DPC basket structural integrity for performance periods of as long as 10,000 years, especially in reducing conditions. Uncertainties include basket component design, disposal environment conditions, and the in-package chemical environment including any localized effects from radiolysis. Prospective disposal overpack materials exist for most disposal environments, including both corrosion allowance and corrosion resistant materials. Whereas the behavior of corrosion allowance materials is understood for a wide range of corrosion environments, demonstrating corrosion resistance could be more technically challenging and require environment-specific testing. A preliminary screening of the existing inventory of DPCs and other types of canisters is described, according to the type of closure, whether they can be readily transported, and what types of materials are used in basket construction.

Pipe Lines – External Corrosion

Directory of Open Access Journals (Sweden)

Dan Babor

2008-01-01

Full Text Available Two areas of corrosion occur in pipe lines: corrosion from the medium carried inside the pipes; corrosion attack upon the outside of the pipes (underground corrosion. Electrolytic processes are also involved in underground corrosion. Here the moisture content of the soil acts as an electrolyte, and the ions required to conduct the current are supplied by water-soluble salts (chlorides, sulfates, etc. present in the soil. The nature and amount of these soluble materials can vary within a wide range, which is seen from the varying electrical conductivity and pH (varies between 3 and 10. Therefore the characteristics of a soil will be an important factor in under-ground corrosion.

Automated Methods Of Corrosion Measurements

DEFF Research Database (Denmark)

Bech-Nielsen, Gregers; Andersen, Jens Enevold Thaulov; Reeve, John Ch

1997-01-01

The chapter describes the following automated measurements: Corrosion Measurements by Titration, Imaging Corrosion by Scanning Probe Microscopy, Critical Pitting Temperature and Application of the Electrochemical Hydrogen Permeation Cell.......The chapter describes the following automated measurements: Corrosion Measurements by Titration, Imaging Corrosion by Scanning Probe Microscopy, Critical Pitting Temperature and Application of the Electrochemical Hydrogen Permeation Cell....

Corrosion and Corrosion Fatigue of Aluminum Alloys: Chemistry, Micromechanics and Reliability

National Research Council Canada - National Science Library

Wei, Robert

1998-01-01

... No. F49620-98-1-0198, to further develop a basic mechanistic understanding of the damage evolution processes of localized corrosion and corrosion fatigue crack nucleation and growth in aluminum alloys...

Corrosion in Electronics

DEFF Research Database (Denmark)

Ambat, Rajan; Gudla, Helene Virginie Conseil; Verdingovas, Vadimas

2017-01-01

Electronic control units, power modules, and consumer electronics are used today in a wide variety of varying climatic conditions. Varying external climatic conditions of temperature and humidity can cause an uncontrolled local climate inside the device enclosure. Uncontrolled humidity together...... and high density packing combined with the use of several materials, which can undergo electrochemical corrosion in the presence of water film formed due to humidity exposure and bias conditions on the PCBA surface. This article provides a short review of the corrosion reliability issues of electronics due...... to the use of electronics under varying humidity conditions. Important PCBA aspects, which are fundamental to the corrosion cell formation under humid conditions, are discussed. Effect of hygroscopic residues from the process and service and their role in assisting water film build up and corrosion...

Assessing resistance of stabilized corrosion resistant steels to intergranular corrosion

International Nuclear Information System (INIS)

Karas, A.; Cihal, V. Jr.; Vanek, V.; Herzan, J.; Protiva, K.; Cihal, V.

1987-01-01

Resistance to intergranular corrosion was determined for four types of titanium-stabilized steels from the coefficients of stabilization efficiency according to the degree the chemical composition was known. The ATA SUPER steel showed the highest resistance parameter value. The resistance of this type of steel of a specific composition, showing a relatively low value of mean nitrogen content was compared with steel of an optimized chemical composition and with low-carbon niobium stabilized, molybdenum modified steels. The comparison showed guarantees of a sufficient resistance of the steel to intergranular corrosion. The method of assessing the resistance to intergranular corrosion using the calculation of the minimum content of Cr', i.e., the effective chromium content, and the maximum effective carbon content C' giving the resistance parameter k seems to be prospective for practical use in the production of corrosion resistant steels. (author). 1 tab., 5 figs., 15 refs

Microbiological corrosion of metals

International Nuclear Information System (INIS)

Vladislavlev, V.V.

1992-01-01

Problems is considered of development of the microbiological corrosion of the NPP equipment. The main attention is paid to the selective character of microbiological corrosion in zones of welded joints of austenitic steels. It is noted that the presence of technological defects promotes growth of corrosional damages. Methods for microbiological corrosion protection are discussed

Corrosion control for low-cost reliability

International Nuclear Information System (INIS)

Anon.

1993-01-01

This conference was held September 19-24, 1993 in Houston, Texas to provide a forum for exchange of state-of-the-art information on corrosion. Topics of interest focus on the following: atmospheric corrosion; chemical process industry corrosion; high temperature corrosion; and corrosion of plant materials. Individual papers have been processed separately for inclusion in the appropriate data bases

A Multifunctional Coating for Autonomous Corrosion Control

Science.gov (United States)

Calle, Luz M.; Li, Wenyan; Buhrow, Jerry W.; Jolley, Scott t.

2011-01-01

Nearly all metals and their alloys are subject to corrosion that causes them to lose their structural integrity or other critical functionality. Protective coatings are the most commonly used method of corrosion control. However, progressively stricter environmental regulations have resulted in the ban of many commercially available corrosion protective coatings due to the harmful effects of their solvents or corrosion inhibitors. This work concerns the development of a multifunctional smart coating for the autonomous control of corrosion. This coating is being developed to have the inherent ability to detect the chemical changes associated with the onset of corrosion and respond autonomously to indicate it and control it. The multi-functionality of the coating is based on microencapsulation technology specifically designed for corrosion control applications. This design has, in addition to all the advantages of existing microcapsulation designs, the corrosion controlled release function that triggers the delivery of corrosion indicators and inhibitors on demand, only when and where needed. Microencapsulation of self-healing agents for autonomous repair of mechanical damage to the coating is also being pursued. Corrosion indicators, corrosion inhibitors, as well as self-healing agents, have been encapsulated and dispersed into several paint systems to test the corrosion detection, inhibition, and self-healing properties of the coating. Key words: Corrosion, coating, autonomous corrosion control, corrosion indication, corrosion inhibition, self-healing coating, smart coating, multifunctional coating, microencapsulation.

New technologies - new corrosion problems

International Nuclear Information System (INIS)

Heitz, E.

1994-01-01

Adequate resistance of materials to corrosion is equally important for classical and for new technologies. This article considers the economic consequences of corrosion damage and, in addition to the long-known GNP orientation, presents a new approach to the estimation of the costs of corrosion and corrosion protection via maintenance and especially corrosion-related maintenance. The significance of ''high-tech'', ''medium-tech'' and ''low-tech'' material and corrosion problems is assessed. Selected examples taken from new technologies in the areas of power engineering, environmental engineering, chemical engineering, and biotechnology demonstrate the great significance of the problems. It is concluded that corrosion research and corrosion prevention technology will never come to an end but will constantly face new problems. Two technologies are of particular interest since they focus attention on new methods of investigation: microelectronics and final disposal of radioactive wastes. The article closes by considering the importance of the transfer of experience and technology. Since the manufacturs and operators of machines and plant do not generally have access to the very latest knowledge, they should be kept informed through advisory services, experimental studies, databases, and further education. (orig.) [de

Corrosion probe. Innovative technology summary report

International Nuclear Information System (INIS)

1999-05-01

Over 253 million liters of high-level waste (HLW) generated from plutonium production is stored in mild steel tanks at the Department of Energy (DOE) Hanford Site. Corrosion monitoring of double-shell storage tanks (DSTs) is currently performed at Hanford using a combination of process knowledge and tank waste sampling and analysis. Available technologies for corrosion monitoring have progressed to a point where it is feasible to monitor and control corrosion by on-line monitoring of the corrosion process and direct addition of corrosion inhibitors. The electrochemical noise (EN) technique deploys EN-based corrosion monitoring probes into storage tanks. This system is specifically designed to measure corrosion rates and detect changes in waste chemistry that trigger the onset of pitting and cracking. These on-line probes can determine whether additional corrosion inhibitor is required and, if so, provide information on an effective end point to the corrosion inhibitor addition procedure. This report describes the technology, its performance, its application, costs, regulatory and policy issues, and lessons learned

Corrosion behaviors of ceramics against liquid sodium. Sodium corrosion characteristics of sintering additives

International Nuclear Information System (INIS)

Tachi, Yoshiaki; Kano, Shigeki; Hirakawa, Yasushi; Yoshida, Eiichi

1998-01-01

It has been progressed as the Frontier Materials Research to research and develop ceramics to apply for several components of fast breeder reactor using liquid sodium as coolant instead of metallic materials. Grain boundary of ceramics has peculiar properties compared with matrix because most of ceramics are produced by hardening and firing their raw powders. Some previous researchers indicated that ceramics were mainly corroded at grain boundaries by liquid sodium, and ceramics could not be used under corrosive environment. Thus, it is the most important for the usage of ceramics in liquid sodium to improve corrosion resistance of grain boundaries. In order to develop the advanced ceramics having good sodium corrosion resistance among fine ceramics, which have recently been progressed in quality and characteristics remarkably, sodium corrosion behaviors of typical sintering additives such as MgO, Y 2 O 3 and AlN etc. have been examined and evaluated. As a result, the followings have been clarified and some useful knowledge about developing advanced ceramics having good corrosion resistance against liquid sodium has been obtained. (1) Sodium corrosion behavior of MgO depended on Si content. Samples containing large amount of Si were corroded severely by liquid sodium, whereas others with low Si contents showed good corrosion resistance. (2) Both Y 2 O 3 and AlN, which contained little Si, showed good sodium corrosion resistance. (3) MgO, Y 2 O 3 and AlN are thought to be corroded by liquid sodium, if they contain some SiO 2 . Therefore, in order to improve sodium corrosion resistance, it is very important for these ceramics to prevent the contamination of matrix with SiO 2 through purity control of their raw powders. (author)

Shadow Corrosion Mechanism of Zircaloy

International Nuclear Information System (INIS)

Ullberg, Mats; Lysell, Gunnar; Nystrand, Ann-Charlotte

2004-02-01

Local corrosion enhancement appears on zirconium-base alloys in-core in boiling water reactors when the zirconium alloy is in close proximity to another metal. The visual appearance often resembles a shadow of the other component. The phenomenon is therefore referred to as 'shadow corrosion'. Shadow corrosion has been known for more than 25 years. Mechanisms based on either galvanic corrosion or local radiolysis effects have been proposed as explanations. Both types of mechanism have seemed to explain some facets of the phenomenon. Normally, shadow corrosion is of no practical significance. However, an enhanced and potentially serious form of shadow corrosion was discovered in 1996. This discovery stimulated new experiments that fully supported neither of the longstanding theories. Thus, there is till now no generally accepted understanding of the shadow corrosion phenomenon. The aim of the present investigation was to analyse the available data and to identify, if possible, a plausible mechanism of shadow corrosion. It was found that the experimental evidence is, with a few exceptions, remarkably consistent with a galvanic mechanism. The main exception is that shadow corrosion may occur also when the two metals are nominally electrically insulated. One way to account for the main exception could be to invoke the effect of photoconductivity. Photoconductivity results when a semiconductor or an insulator is irradiated with photons of UV or higher energy. The photons elevate electrons from the valence band to the conduction band, thereby raising the electron conductivity of the solid. In particular, photoconductivity lowers the electrical resistance of the normally insulating oxide on zirconium base alloys. Photoconductivity therefore also has the potential to explain why shadow corrosion is only seen in, or in proximity to, a nuclear reactor core. The suggested mechanism of shadow corrosion can be tested in a reasonably simple experiment in a research reactor

Effect of flow on corrosion in catenary risers and its corrosion inhibitor performance

Energy Technology Data Exchange (ETDEWEB)

Ferreira, Pedro Altoe; Magalhaes, Alvaro Augusto Oliveira; Silva, Jussara de Mello [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil); Kang, Cheolho; More, Parimal P. [Det Norske Veritas (DNV), Oslo (Norway)

2009-07-01

In oil and gas production, multiphase flow is often encountered and a range of different flow patterns can be experienced in pipelines. The flow regime transition and flow characteristics can be changed with the change of pipeline topography, which affects the corrosion and the performance of corrosion inhibitor in these multiphase pipelines. This paper outlines on the effect of inclination on the flow characteristics and their subsequent effect on corrosion rates. Also, this paper presents on the performance of three candidate corrosion inhibitors under severe slugging conditions at low water cut. For the simulation of offshore flow lines and risers, the experiments were carried out in a 44 m long, 10 cm diameter, three different pipeline inclinations of 0, 3 and 45 degrees. Light condensate oil with a viscosity of 2.5 cP at room temperature was used and water cut was 20%. The results indicated that the baseline corrosion rate in 45 degrees showed higher than other inclinations. Each corrosion inhibitor showed a different inhibitor performance. (author)

CHECWORKS integrated software for corrosion control

International Nuclear Information System (INIS)

Schefski, C.; Pietralik; Hazelton, T.

1997-01-01

CHECWORKS, a comprehensive software package for managing Flow-Accelerated Corrosion (FAC, also called erosion-corrosion and flow-assisted corrosion) concerns, is expanding to include other systems and other aspects of corrosion control in CANDU reactors. This paper will outline CHECWORKS applications at various CANDU stations and further plans for CHECWORKS to become a code for comprehensive corrosion control management. (author)

The resistance of titanium to pitting, microbially induced corrosion and corrosion in unsaturated conditions

International Nuclear Information System (INIS)

Shoesmith, D.W.; Ikeda, B.M.

1997-04-01

Titanium and its alloys (Grades-2, -12, -16) are candidate materials for Canadian nuclear waste containers on the basis of their apparent immunity to many localized corrosion processes. This simplifies markedly the effort needed to justify the use of these materials and to develop models to predict the lifetimes of containers. Here we review the pitting, microbially influenced corrosion (MIC), and corrosion under unsaturated conditions, of titanium. For all these processes, the properties of the passive oxide film are paramount in determining the metal's resistance to corrosion. A review of these oxide properties is included and the conditions to which the metal must be exposed if localized corrosion is to occur are defined. Since these conditions cannot be achieved under Canadian waste vault conditions, it can be concluded that pitting and MIC will not occur and that corrosion under unsaturated conditions is extremely unlikely. (author)

The Effects of Corrosive Chemicals on Corrosion Rate of Steel Reinforcement Bars: II. Swamp Sludges

Directory of Open Access Journals (Sweden)

Henki Ashadi

2010-10-01

Full Text Available A polluted environment will influence the building age. The objective of this research was to find out the influence of corrosive chemicals within the sludge swamp area with the corrosion rate of steel concrete. Corrosion in steel concrete usually occur in acid area which contain of SO42-, Cl- and NO3-. The research treatment used by emerging ST 37 andST 60 within 60 days in 'polluted' sludge swamp area. Three variation of 'polluted' swamp sludge were made by increasing the concentration a corrosive unsure up to 1X, 5X and 10X. The corrosion rate measured by using an Immersion Method. The result of Immersion test showed that sulphate had a greatest influence to corrosion rate of ST 37 and ST 60 and followed by chloride and nitrate. Corrosion rate value for ST 37 was 17.58 mpy and for ST 60 was 12.47 mpy.

Materiales, tecnologías y prototipos de viviendas de muy bajo coste

Directory of Open Access Journals (Sweden)

Salas Serrano, Julián

1982-11-01

Full Text Available Not available.El fin último de la investigación es el de conseguir unas tipologías de viviendas realizadas mediante materiales, procedimientos o sistemas constructivos que permitan proporcionar un producto final, cuyas características fundamentales sean: adecuación a las necesidades físicas y socioculturales de la zona y, prioritariamente, la consecución de un muy bajo coste da ejecución de las mismas. Cuando se habla a continuación de «viviendas de muy bajo coste» se debe entender que nos referimos a las que cumplen básicamente las dos condiciones limitativas aceptadas por las Naciones Unidas (UNCHSHABITAT: a Superficie construida comprendida entre 30 y 50 m2. b Coste de construcción inferior a los 100 $ USA (1982 por metro cuadrado construido. (Para nuestras condiciones, fijaríamos un coste aproximado de 10.000 pts/m2.

Protecting solar collector systems from corrosion

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

The main cause of the reduced life of a solar heating system is corrosion of the exterior parts and the internal components. This report outlines ways of reducing the cost of solar heating by reducing the corrosion in solar heating systems, and hence increasing the system's service life. Mechanisms for corrosion are discussed: these include galvanic corrosion and crevice corrosion. Means of minimizing corrosion at the design stage are then described. Such methods, when designing the solar collector, involve ensuring proper drainage of exterior water; eliminating situations where moisture, dirt and pollutants may collect; preventing condensation inside the collector; using proper gaskets and sealants at appropriate places; and selecting optimum materials and coatings. Interior corrosion can be minimized at the design stage by choosing a good heat transfer fluid and corrosion inhibitor, in the case of systems where liquids are used; ensuring a low enough flow rate to avoid erosion; designing the system to avoid crevices; and avoiding situations where galvanic corrosion could occur. Other procedures are given for minimizing corrosion in the construction and operation of solar heating systems. 7 figs., 7 tabs.

DESARROLLO E IMPLEMENTACIÓN DE FOTOCONTROL TEMPORIZADO CON TECNOLOGÍA DE BAJO CONSUMO

Directory of Open Access Journals (Sweden)

Fredy Hernán Martínez Sarmiento

2013-09-01

Full Text Available En este trabajo se presenta el desarrollo e implementación de un fotocontrol con tecnología de bajo consumo desarrollado con un microcontrolador, el cual controla variables de tensión, luminosidad  y sincronización con la red, por medio de  una salida con modo PWM producir una salida de Vdc en el relé. El microcontrolador realiza un  muestreo análogo de voltaje sobre la onda sinusoidal y se hace un filtro de promedio móvil para eliminar ruido de la onda.La temporización se realiza cuando el contacto del relé está cerrado y el tiempo a temporizar es programado por el usuario el cual lo requiera, el fotocontrol presenta un modo de ultra bajo consumo en el microcontrolador con un supercap.

Prediction of reinforcement corrosion using corrosion induced cracks width in corroded reinforced concrete beams

International Nuclear Information System (INIS)

Khan, Inamullah; François, Raoul; Castel, Arnaud

2014-01-01

This paper studies the evolution of reinforcement corrosion in comparison to corrosion crack width in a highly corroded reinforced concrete beam. Cracking and corrosion maps of the beam were drawn and steel reinforcement was recovered from the beam to observe the corrosion pattern and to measure the loss of mass of steel reinforcement. Maximum steel cross-section loss of the main reinforcement and average steel cross-section loss between stirrups were plotted against the crack width. The experimental results were compared with existing models proposed by Rodriguez et al., Vidal et al. and Zhang et al. Time prediction models for a given opening threshold are also compared to experimental results. Steel cross-section loss for stirrups was also measured and was plotted against the crack width. It was observed that steel cross-section loss in the stirrups had no relationship with the crack width of longitudinal corrosion cracks. -- Highlights: •Relationship between crack and corrosion of reinforcement was investigated. •Corrosion results of natural process and then corresponds to in-situ conditions. •Comparison with time predicting model is provided. •Prediction of load-bearing capacity from crack pattern was studied

A non-destructive test method to monitor corrosion products and corrosion-induced cracking in reinforced cement based materials

DEFF Research Database (Denmark)

Michel, Alexander; Pease, Bradley Justin; Peterova, Adela

2011-01-01

) was conducted to describe the impact of water-to-cement ratio and corrosion current density (i.e., corrosion rate) on the reinforcement corrosion process. Focus was placed, in particular on the determination of the corrosion accommodating region (CAR) and time to corrosion-induced cracking. Experimental results...... showed that x-ray attenuation measurements allow determination of the actual concentrations of corrosion products averaged through the specimen thickness. The total mass loss of steel measured by x-ray attenuation was found to be in very good agreement with the calculated mass loss obtained by Faraday......’s law. Furthermore, experimental results demonstrated that the depth of penetration of corrosion products as well as time to corrosion-induced cracking is varying for the different water-to-cement ratios and applied corrosion current densities....

Corrosion and protection of magnesium alloys

Energy Technology Data Exchange (ETDEWEB)

Ghali, E. [Laval Univ., Quebec City, PQ (Canada). Dept. of Mining and Metallurgy

2000-07-01

The oxide film on magnesium offers considerable surface protection in rural and some industrial environments and the corrosion rate lies between that of aluminum and low carbon steels. Galvanic coupling of magnesium alloys, high impurity content such as Ni, Fe, Cu and surface contamination are detrimental for corrosion resistance of magnesium alloys. Alloying elements can form secondary particles which are noble to the Mg matrix, thereby facilitating corrosion, or enrich the corrosion product thereby possibly inhibiting the corrosion rate. Bimetallic corrosion resistance can be increased by fluxless melt protection, choice of compatible alloys, insulating materials, and new high-purity alloys. Magnesium is relatively insensible to oxygen concentration. Pitting, corrosion in the crevices, filiform corrosion are observed. Granular corrosion of magnesium alloys is possible due to the cathodic grain-boundary constituent. More homogeneous microstructures tend to improve corrosion resistance. Under fatigue loading conditions, microcrack initiation in Mg alloys is related to slip in preferentially oriented grains. Coating that exclude the corrosive environments can provide the primary defense against corrosion fatigue. Magnesium alloys that contain neither aluminum nor zinc are the most SCC resistant. Compressive surface residual stresses as that created by short peening increase SCC resistance. Cathodic polarization or cladding with a SCC resistant sheet alloy are good alternatives. Effective corrosion prevention for magnesium alloy components and assemblies should start at the design stage. Selective surface preparation, chemical treatment and coatings are recommended. Oil application, wax coating, anodizing, electroplating, and painting are possible alternatives. Recently, it is found that a magnesium hydride layer, created on the magnesium surface by cathodic charging in aqueous solution is a good base for painting. (orig.)

Efecto de los parámetros geomecánicos en el fracturamiento hidráulico de yacimientos de hidrocarburos sensibles a esfuerzos

OpenAIRE

Naranjo A., Abel; Soto J ., Carlos M.

2008-01-01

La teoría sobre el proceso de fracturamiento hidráulico indica que se requiere acoplar el comportamiento de la roca y el comportamiento del fluido para un modelamiento exitoso del tratamiento. En el presente trabajo se analizan los efectos de las propiedades geomecánicas en el fracturamiento hidráulico para yacimientos de hidrocarburos sensibles a esfuerzos.Se desarrolla un software para simular el fracturamiento hidráulico en tres dimensiones en diferencias finitas, que acopla el flujo de fl...

High Temperature Corrosion under Laboratory Conditions Simulating Biomass-Firing: A Comprehensive Characterization of Corrosion Products

DEFF Research Database (Denmark)

Okoro, Sunday Chukwudi; Montgomery, Melanie; Jappe Frandsen, Flemming

2014-01-01

characterization of the corrosion products. The corrosion products consisted of three layers: i) the outermost layer consisting of a mixed layer of K2SO4 and FexOy on a partly molten layer of the initial deposit, ii) the middle layer consists of spinel (FeCr2O4) and Fe2O3, and iii) the innermost layer is a sponge......-like Ni3S2 containing layer. At the corrosion front, Cl-rich protrusions were observed. Results indicate that selective corrosion of Fe and Cr by Cl, active oxidation and sulphidation attack of Ni are possible corrosion mechanisms....

Corrosion of X65 Pipeline Steel Under Deposit and Effect of Corrosion Inhibitor

Directory of Open Access Journals (Sweden)

XU Yun-ze

2016-10-01

Full Text Available Effect of the deposit on the electrochemical parameters of X65 pipeline steel in oxygen contained sodium chloride solution was studied by EIS and PDS methods. The galvanic corrosion behavior under deposit and effect of different concentration of corrosion inhibitor PBTCA were studied by electrical resistance (ER method combined with ZRA. The results show that the corrosion potential of X65 steel shifts negatively as SiO2 covering its surface and the corrosion rate becomes lower. When the galvanic couple specimen with deposit is electrically connected with the specimen without deposit, anodic polarization occurs on X65 steel under deposit and the galvanic current density decreases from 120μA/cm2 to 50μA/cm2 and keeps stable. As 5×10-5, 8×10-5 and 3×10-4 PBTCA were introduced into the solution, the galvanic current density reaches the highest 1300μA/cm2 and then decreases to 610μA/cm2 keeping stable around 610μA/cm2, corrosion rate of X65 steel under deposit reaches 6.11mm/a. PBTCA accelerates the corrosion of X65 steel under deposit in oxygen contained solution. Through the investigation on the surface of the specimens, serious local corrosion occurs on the X65 steel surface under deposit.

Limitación del esfuerzo terapéutico: aspectos religiosos y culturales

Directory of Open Access Journals (Sweden)

Gilberto de Jesús Betancourt Betancourt

Full Text Available La comprensión de la muerte varía según la época, la cultura, la religión y la edad. Con anterioridad al desarrollo que la ciencia médica ha experimentado desde finales del siglo XIX, en la mayoría de las culturas y religiones había una aceptación de la muerte y se consideraba como parte del ciclo vital de la persona donde se trascendía a una forma celestial y puramente sobrenatural. Los avances científicos de la medicina han venido a cambiar esta situación. La muerte se empezó a ver como un enemigo y dio comienzo a una lucha encarnizada entre ambas. El concepto de "muerte natural" se sustituyó por el de "muerte intervenida," dando origen a numerosas cuestiones relacionadas con la toma de decisiones y actuaciones a realizar en pacientes ingresados y en situación terminal. En este trabajo se realiza una reflexión teórica que tiene como objetivo el análisis bioético acerca de las diferencias entre los aspectos religiosos y culturales relacionados con la práctica de la limitación del esfuerzo terapéutico.

The resistance of titanium to pitting, microbially induced corrosion and corrosion in unsaturated conditions

Energy Technology Data Exchange (ETDEWEB)

Shoesmith, D W; Ikeda, B M

1997-04-01

Titanium and its alloys (Grades-2, -12, -16) are candidate materials for Canadian nuclear waste containers on the basis of their apparent immunity to many localized corrosion processes. This simplifies markedly the effort needed to justify the use of these materials and to develop models to predict the lifetimes of containers. Here we review the pitting, microbially influenced corrosion (MIC), and corrosion under unsaturated conditions, of titanium. For all these processes, the properties of the passive oxide film are paramount in determining the metal`s resistance to corrosion. A review of these oxide properties is included and the conditions to which the metal must be exposed if localized corrosion is to occur are defined. Since these conditions cannot be achieved under Canadian waste vault conditions, it can be concluded that pitting and MIC will not occur and that corrosion under unsaturated conditions is extremely unlikely. (author) 114 refs., 1 tab., 18 figs.

Corrosion fatigue of steels

International Nuclear Information System (INIS)

Spaehn, H.; Wagner, G.H.

1976-01-01

Corrosion fatigue phenomena can be classified into two main groups according to the electrochemical state of the metal surface in the presence of electrolytes: the active and the passive state with an important sub-group of corrosion fatigue in the unstable passive state. The allowable stress for structures exposed to the conjoint action of corrosion and fatigue is influenced by many factors: kind of media, number of cycles, frequency, mean stress, size, notches, loading mode, alloy composition and mechanical strength. A critical literature review shows contradictory results if a classification by the electrochemical surface state is not applied. Case histories and counter measures illustrate the practical importance of corrosion fatigue in many branches of industry as well as the urgent need for a better knowledge about the mutual influence of the phenomena to get rules by which the engineer can appraise the risk of corrosion fatigue. (orig.) [de

Cathodic corrosion: Part 2. Properties of nanoparticles synthesized by cathodic corrosion

International Nuclear Information System (INIS)

Yanson, A.I.; Yanson, Yu.I.

2013-01-01

We demonstrate how cathodic corrosion in concentrated aqueous solutions enables one to prepare nanoparticles of various metals and metal alloys. Using various characterization methods we show that the composition of nanoparticles remains that of the starting material, and the resulting size distribution remains rather narrow. For the case of platinum we show how the size and possibly even the shape of the nanoparticles can be easily controlled by the parameters of corrosion. Finally, we discuss the advantages of using the nanoparticles prepared by cathodic corrosion for applications in (electro-)catalysis.

Corrosion of high-density sintered tungsten alloys

International Nuclear Information System (INIS)

Batten, J.J.; Moore, B.T.

1989-01-01

In comparative corrosion tests, the corrosion resistance of an Australian tungsten alloy (95% W, 3.5% Ni, 1.5% Fe) was found to be superior to three other tungsten alloys and, under certain conditions, even more corrosion-resistant than pure tungsten. Corrosion resistance was evaluated after immersion in both distilled water and 5% sodium chloride solutions, and in cyclic humidity and salt mist environments. For all but the Australian alloy, the rate of corrosion in sodium chloride solution was markedly less than that in distilated water. In all cases, alloys containing copper had the greatest corrosion rates. Corrosion mechanisms were investigated using a scanning electron microscope, analysis of corrosion products and galvanic corrosion studies. For the alloys, corrosion was attributed primarily to a galvanic reaction. Whether the tungsten or binder phase of the alloy became anodic, and thus was attacked preferentially, depended upon alloy composition and corrosion environment. 16 refs., 4 tabs., 4 figs

Internal corrosion control of northern pipelines

Energy Technology Data Exchange (ETDEWEB)

Papavinasam, S.

2005-02-01

The general causes of internal corrosion in pipelines were discussed along with the methods to control them. Efficient methods are needed to determine chemical efficiency for mitigating internal corrosion in transmission pipelines, particularly those used in environmentally sensitive regions in the Arctic where harsh environmental conditions prevail. According to the Office of Pipeline Safety, 15 per cent of pipeline failures in the United States from 1994 to 2000 were caused by internal corrosion. Since pipelines in the United States are slightly older than Canadian pipelines, internal corrosion is a significant issue from a Canadian perspective. There are 306,618 km of energy-related pipelines in western Canada. Between April 2001 and March 2002 there were 808 failures, of which 425 failures resulted from internal corrosion. The approach to control internal corrosion comprises of dehydrating the gases at production facilities; controlling the quality of corrosive gases such as carbon dioxide and hydrogen sulphide; and, using internal coatings. The approaches to control internal corrosion are appropriate, when supplemented by adequate integrity management program to ensure that corrosive liquids do not collect, over the operational lifetime of the pipelines, at localized areas. It was suggested that modeling of pipeline operations may need improvement. This paper described the causes, prediction and control of internal pitting corrosion. It was concluded that carbon steel equipment can continue to be used reliably and safely as pipeline materials for northern pipelines if the causes that lead to internal corrosion are scientifically and accurately predicted, and if corrosion inhibitors are properly evaluated and applied. 5 figs.

An electrochemical investigation of the corrosion behavior of Al-Si-Cu hypereutectic alloys in alcoholic environments

Directory of Open Access Journals (Sweden)

Traldi, S. M.

2003-12-01

Full Text Available Al-Si-Cu hypereutetic alloys produced by spray forming are mostly used in the automotive industry, especially for cylinder liners. They have the advantage of low weight associated with low coefficient of thermal expansion and excellent mechanical properties - mainly wear resistance at high temperatures. The corrosion resistance of these alloys in fuels, particularly alcoholic media, however is not yet known. In this investigation, electrochemical impedance spectroscopy (EIS and potentiodynamic polarisation have been used to evaluate the corrosion resistance of a hypereutectic Al-Si-Cu alloy in alcoholic environments. The EIS tests were carried out in pure ethanol, and ethanol with small additions (1 mM of acid and chloride, to investigate the effect of these contaminants on corrosion resistance. The corrosion resistance of a grey cast iron has also been evaluated in pure ethanol for comparison. The Al-Si-Cu alloy showed high corrosion resistance in pure ethanol, far superior to that of grey cast iron in the same medium.

Aleaciones hipereutécticas producidas por conformación por spray son muy empleadas en la industria automovilística, especialmente en los revestimientos de los cilindros. Tienen la ventaja de añadir menos peso con bajo coeficiente de expansión térmica y excelentes propiedades mecánicas, sobre todo resistencia al desgaste en altas temperaturas. Todavía, la resistencia a la corrosión de estas aleaciones en combustibles no es conocida. En este estudio fueron utilizadas las técnicas de espectroscopia de impedancia electroquímica y polarización potenciodinámica, para evaluar la resistencia a la corrosión de una aleación hipereutéctica Al-Si-Cu en medio alcohólico. Las pruebas fueron conducidas en etanol puro y etanol con pequeñas adiciones (1 mM de ácido y cloruro, con la finalidad de investigar el efecto de estos contaminantes en la resistencia a la corrosión. Hierro fundido gris, también fue

Dinámica espacio-temporal del esfuerzo en una pesquería de buceo artesanal multiespecífica y sus efectos en la variabilidad de las capturas: Implicaciones para el manejo sostenible

Directory of Open Access Journals (Sweden)

Helven Naranjo Madrigal

2014-12-01

Full Text Available Las pesquerías artesanales asociadas a métodos de buceo son fuente de ingreso, empleo y seguridad alimentaria de zonas costeras en muchos países. Los altos precios y la poca movilidad de especies bénticas capturadas por buceo enfrentan retos cada vez mayores en su aprovechamiento y manejo, esto demanda un entendimiento integral de estas pesquerías en diferentes contextos, incluyendo la dinámica espacial y temporal del esfuerzo pesquero, las artes y las especies. En el presente estudio se busca elucidar si existen diferencias en las estrategias de pesca desarrolla- das por pescadores que emplean buceo en dos modalidades (hookah y buceo libre. También se busca conocer si se desarrollan adaptaciones de estas estrategias en el tiempo, bajo qué condiciones y el posible efecto de las estrategias sobre las capturas. Para ese fin se analizó información detallada de las operaciones de pesca de embarcaciones artesanales que operan en la costa del océano Pacífico de Costa Rica durante dos temporadas de pesca. Se analizó información obtenida a bordo de embarcaciones como: sitio de pesca, composición de especies, tiempo de pesca, número de inmersiones por viaje, entre otros; y se aplicaron entrevistas a buzos al momento de las descargas para obtener información de precios, el volumen de las especies capturadas y forma de operación de los pescadores. Para el buceo con hookah se obtuvo una muestra del 69.3% del total de viajes en las dos temporadas de pesca y en el caso del buceo libre se obtuvo una muestra del 41.9% del total de viajes en las dos temporadas de pesca estudiadas (2007-2008 y 2011-2012. Se identificaron más de 15 especies en cada temporada de pesca, dominaron tres categorías en ambas temporadas pero con diferencias en las proporciones obtenidas en cada caso: langosta (Panulirus gracilis, pulpo (Octopus sp y pez loro (Scarus perrico y S. Ghobban. Resalta un componente importante de captura retenida por los pescadores para

Corrosion '98: 53. annual conference and exposition, proceedings

International Nuclear Information System (INIS)

Anon.

1998-01-01

This conference was divided into the following sections: Corrosion in Gas Treating; Problems and Solutions in Commercial Building Water Systems; Green Corrosion/Scale Inhibitors; Atmospheric Corrosion; AIRPOL Update/98; Rubber Lining--Answers to Many Problems; Interference Problems; Environmental Assisted Cracking: Fundamental Research and Industrial Applications; Corrosion in Nuclear Systems; New Developments in Scale and Deposit Control; Corrosion and Corrosion Protection in the Transportation Industries; What's All the Noise About--Electrochemical That Is; Refining Industry Corrosion; Corrosion Problems in Military Hardware: Case Histories, Fixes and Lessons Learned; Cathodic Protection Test Methods and Instrumentation for Underground and On-grade Pipelines and Tanks; Recent Developments in Volatile Corrosion Inhibitors; Corrosion in Supercritical Fluids; Microbiologically Influenced Corrosion; Advances in Understanding and Controlling CO 2 Corrosion; Managing Corrosion with Plastics; Material Developments for Use in Exploration and Production Environments; Corrosion in Cold Regions; The Effect of Downsizing and Outsourcing on Cooling System Monitoring and Control Practices; New Developments in Mechanical and Chemical Industrial Cleaning; Mineral Scale Deposit Control in Oilfield Related Operations; Biocides in Cooling Water; Corrosion and Corrosion Control of Reinforced Concrete Structures; Materials Performance for Fossil Energy Conversion Systems; Marine corrosion; Thermal Spray--Coating and Corrosion Control; Flow Effects on Corrosion in Oil and Gas Production; Corrosion Measurement Technologies; Internal Pipeline Monitoring--Corrosion Monitoring, Intelligent Pigging and Leak Detection; Cathodic Protection in Natural Waters; Corrosion in Radioactive Liquid Waste Systems; On-line Hydrogen Permeation Monitoring Equipment and Techniques, State of the Art; Water Reuse and Recovery; Performance of Materials in High Temperature Environments; Advances in Motor

Screening of soil corrosivity by field testing: Results and design of an electrochemical soil corrosion probe

DEFF Research Database (Denmark)

Nielsen, Lars vendelbo; Bruun, Niels Kåre

1996-01-01

The corrosivity of different types of soil have been assessed by exposing carbon-steel plates at 50 different locations in Denmark for an extended period of time. The investigations included weight loss measurements and analysis of the chemical compositions of the corrosion products formed...... on the plates during exposure. An electrochemical soil corrosion probe has been designed and manufactured allowing for simultaneous measurements of several qauntities to predict corrosion. The probe consists of individual sections capable of measuring redox-potential, corrosion potential, soil resistivity...

Corrosion behaviour of the UO2 pellet in corrosive solutions using electrochemical Technique

International Nuclear Information System (INIS)

Taftanzani, A.; Sucipto; Lahagu, F.; Irianto, B.

1996-01-01

The UO 2 electrodes has been made from the local product of UO 2 pellets. The corrosion behaviour of the UO 2 pellets is affected by solution, by pH value and by concentration of salt solution. Investigation into corrosion behaviour of UO 2 electrodes have been carried out in saturated salt solutions using electrochemical technique. The saturated solutions have been made from salts NaCl, Na 2 CO 3 , Na 2 SO 4 and Na 3 PO 4 . The pH value have been done over range 1 pH 10 and the salt concentration (C) over range 0,001 mol/l C 1,0 mol/l, Na 2 CO 3 solution produced the lowest corrosion rates of UO 2 pellets. Those rates were relative constant in the range of pH = 4 - 8. The results indicate an influence of the Na 2 CO 3 concentrations on the corrosions on the corrosion rate, and the lowest rates occur in 0,10 mol/l Na 2 CO 3 . The lowest corrosion rate was 0.3388 mil/year in 0.10 mol/l Na 2 CO 3 by pH = 4. (author)

Relationship between Corrosion Level of Rebar Embedded in Concrete, Corrosion Potential and Current Density Measured by Non-destructive Test Method

International Nuclear Information System (INIS)

Chung, Lan; Cho, Seung Ho; Roh, Young Sook; Kim, Joong Koo

2004-01-01

The purpose of this study is to identify corrosion mechanism and develop qualitative measurement method of corrosion level. Fist of all, structural behavior of each different level of corrosion states have been evaluated. And mathematical models that can predict corrosion level in terms of electric potential and corrosion intensity are proposed. Corrosion rate in reinforcing bar was investigated in this study using accelerated corrosion method due to electric potential differences based on Faradays law. Total 288 measurement spots were designed in terms of corrosion rates, diameter of reinforcing bars, and concrete cover thickness. Corrosion current densities and corrosion potentials of concrete were measured on these specimens using Gecor device. This study suggested the relationship between corrosion levels, and measured electric current density as follows

Modeling of Corrosion-induced Concrete Damage

DEFF Research Database (Denmark)

Thybo, Anna Emilie A.; Michel, Alexander; Stang, Henrik

2013-01-01

In the present paper a finite element model is introduced to simulate corrosion-induced damage in concrete. The model takes into account the penetration of corrosion products into the concrete as well as non-uniform formation of corrosion products around the reinforcement. To ac-count for the non...... of corrosion products affects both the time-to cover cracking and the crack width at the concrete surface.......In the present paper a finite element model is introduced to simulate corrosion-induced damage in concrete. The model takes into account the penetration of corrosion products into the concrete as well as non-uniform formation of corrosion products around the reinforcement. To ac-count for the non......-uniform formation of corrosion products at the concrete/reinforcement interface, a deterministic approach is used. The model gives good estimates of both deformations in the con-crete/reinforcement interface and crack width when compared to experimental data. Further, it is shown that non-uniform deposition...

Bridging of inspection with corrosion management

International Nuclear Information System (INIS)

Zamaluddin Ali; Mohd Hawari Hassan; Rohana Jaafar

2009-01-01

Formerly, Inspection and Corrosion Engineers have less interaction and sharing of information to each other even they are working in the same plant or organization. Inspection finding either from visual inspection or NDT techniques rarely shared with corrosion engineers. Similarly corrosion engineers rarely discussed their corrosion prediction and potential damage mechanism with inspection engineers. A demanding request of more holistic plant safety and asset integrity promoted the introduction and implementation of Risk Based Inspection (RBI). RBI analysis demands the input mainly from both disciplines i.e. Inspection and Corrosion Engineers. Most of RBI methodologies are once-off analysis approach which also promoted once-off interaction between Inspection and Corrosion Engineers. PETRONAS has developed a methodology with supporting software, integrating both Inspection and Corrosion disciplines. PETRONAS Risk Based Inspection (PRBI) is intended to promote continuous integration of Inspection and Corrosion management of the plant through out the whole life cycle starting from the design stage to fabrication, operation and decommissions stage. (author)

Steam generator corrosion 2007; Dampferzeugerkorrosion 2007

Energy Technology Data Exchange (ETDEWEB)

Born, M. (ed.)

2007-07-01

Between 8th and 9th November, 2007, SAXONIA Standortentwicklungs- und -verwertungsgesellschaft GmbH (Freiberg, Federal Republic of Germany) performed the 3rd Freiberger discussion conference ''Fireside boiler corrosion''. The topics of the lectures are: (a) Steam generator corrosion - an infinite history (Franz W. Alvert); (b) CFD computations for thermal waste treatment plants - a contribution for the damage recognition and remedy (Klaus Goerner, Thomas Klasen); (c) Experiences with the use of corrosion probes (Siegfried R. Horn, Ferdinand Haider, Barbara Waldmann, Ragnar Warnecke); (d) Use of additives for the limitation of the high temperature chlorine corrosion as an option apart from other measures to the corrosion protection (Wolfgang Spiegel); (e) Current research results and aims of research with respect to chlorine corrosion (Ragnar Warnecke); (f) Systematics of the corrosion phenomena - notes for the enterprise and corrosion protection (Thomas Herzog, Wolfgang Spiegel, Werner Schmidl); (g) Corrosion protection by cladding in steam generators of waste incinerators (Joerg Metschke); (h) Corrosion protection and wear protection by means of thermal spraying in steam generators (Dietmar Bendix); (i) Review of thick film nickelized components as an effective protection against high-temperature corrosion (Johann-Wilhelm Ansey); (j) Fireproof materials for waste incinerators - characteristics and profile of requirement (Johannes Imle); (k) Service life-relevant aspects of fireproof linings in the thermal recycling of waste (Till Osthoevener and Wolfgang Kollenberg); (l) Alternatives to the fireproof material in the heating space (Heino Sinn); (m) Cladding: Inconal 625 contra 686 - Fundamentals / applications in boiler construction and plant construction (Wolfgang Hoffmeister); (n) Thin films as efficient corrosion barriers - thermal spray coating in waste incinerators and biomass firing (Ruediger W. Schuelein, Steffen Hoehne, Friedrich

Future and benefits of corrosion research

International Nuclear Information System (INIS)

Staehle, Roger W.

2002-01-01

The subject of corrosion is a design science. The subject of stress analysis is a design science as is the subject of heat transfer. When the subject of corrosion is considered in the framework design a clear framework of the priorities and objectives becomes apparent. Further, corrosion becomes a more explicit and important subject in the overall design, manufacturing, and operation phases of equipment: in this framework, the funding and support of corrosion work is necessary to the designers and users of equipment. The subject of corrosion is usually less important in the early stages of operation of equipment: in these early stages, the subjects. Corrosion becomes important to the longer term reliability and safety of equipment. Corrosion is often a principal determiner of design life. Corrosion is often more important after the manufacturing warranty is expired: therefore the subject is often more important to the user than to the manufacturer. In order that the subject of corrosion is considered and incorporated in the design as well as in user specifications, there must be a language and means of easily understood communication between the design-operation community and the corrosion community. For example, the designers do not understand the language of 'pitting potential': rather, they understand design life and permissible stress. Thus, corrosion must be put into terms that can be understood and utilized by designers and operators. Two methodologies have been developed for communicating effectively between the corrosion and the design communities: these are the 'Corrosion Based Design Approach' and the 'Location for Analysis Matrix.' These provide simple check off lists to designers for asking questions and assuring that credible answers have been obtained on issues that affect reliable and economic performance. Both of these subject are discussed in this presentation. The future of corrosion research is its effective linkage with design and operation of

Stochastic theory of fatigue corrosion

Science.gov (United States)

Hu, Haiyun

1999-10-01

A stochastic theory of corrosion has been constructed. The stochastic equations are described giving the transportation corrosion rate and fluctuation corrosion coefficient. In addition the pit diameter distribution function, the average pit diameter and the most probable pit diameter including other related empirical formula have been derived. In order to clarify the effect of stress range on the initiation and growth behaviour of pitting corrosion, round smooth specimen were tested under cyclic loading in 3.5% NaCl solution.

Zircaloy-4 corrosion in PWR's

International Nuclear Information System (INIS)

Fyfitch, S.; Smalley, W.R.; Roberts, E.

1985-01-01

Zircaloy-4 waterside corrosion has been studied extensively in the nuclear industry for a number of years. Following the early crud-related corrosion failures in the Saxton test reactor, Westinghouse undertook numerous programs to minimize crud deposition on fuel rods in power reactors through primary coolant chemistry control. Modern plants today are operating with improved coolant chemistry guidelines, and crud deposition levels are very low in proportion to earlier experience. Zircaloy-4 corrosion under a variety of coolant chemistry, heat flux and exposure conditions has been studied extensively. Experience to date, even in relatively high coolant temperature plants, has indicated that -for both fuel cladding and structural components- Zircaloy-4 waterside corrosion performance has been excellent. Recognizing future industry trends, however, which will result in Zircaloy-4 being subjected to ever increasing corrosion duties, Westinghouse will continue accumulating Zircaloy-4 corrosion experience in large power plants. 13 refs.

Nuclear corrosion science and engineering

CERN Document Server

2012-01-01

Understanding corrosion mechanisms, the systems and materials they affect, and the methods necessary for accurately measuring their incidence is of critical importance to the nuclear industry for the safe, economic and competitive running of its plants. This book reviews the fundamentals of nuclear corrosion. Corrosion of nuclear materials, i.e. the interaction between these materials and their environments, is a major issue for plant safety as well as for operation and economic competitiveness. Understanding these corrosion mechanisms, the systems and materials they affect, and the methods to accurately measure their incidence is of critical importance to the nuclear industry. Combining assessment techniques and analytical models into this understanding allows operators to predict the service life of corrosion-affected nuclear plant materials, and to apply the most appropriate maintenance and mitigation options to ensure safe long term operation. This book critically reviews the fundamental corrosion mechani...

Corrosion management in nuclear industry

International Nuclear Information System (INIS)

Kamachi Mudali, U.

2012-01-01

Corrosion is a major degradation mechanism of metals and alloys which significantly affects the global economy with an average loss of 3.5% of GDP of several countries in many important industrial sectors including chemical, petrochemical, power, oil, refinery, fertilizer etc. The demand for higher efficiency and achieving name plate capacity, in addition to ever increasing temperatures, pressures and complexities in equipment geometry of industrial processes, necessitate utmost care in adopting appropriate corrosion management strategies in selecting, designing, fabricating and utilising various materials and coatings for engineering applications in industries. Corrosion control and prevention is an important focus area as the savings achieved from practicing corrosion control and prevention would bring significant benefits to the industry. Towards this, advanced corrosion management strategies starting from design, manufacturing, operation, maintenance, in-service inspection and online monitoring are essential. At the Indira Gandhi Centre for Atomic Research (IGCAR) strategic corrosion management efforts have been pursued in order to provide solutions to practical problems emerging in the plants, in addition to innovative efforts to provide insight into mechanism and understanding of corrosion of various engineering materials and coatings. In this presentation the author highlights how the nuclear industry benefited from the practical approach to successful corrosion management, particularly with respect to fast breeder reactor programme involving both reactor and associated reprocessing plants. (author)

Corrosion control in nuclear fuel reprocessing

International Nuclear Information System (INIS)

Steele, D.F.

1986-01-01

This article looks in detail at tribology-related hazards of corrosion in irradiated fuel reprocessing plants and tries to identify and minimize problems which could contribute to disaster. First, the corrosion process is explained. Then the corrosion aspects at each of four stages in reprocessing are examined, with particular reference to oxide fuel reprocessing. The four stages are fuel receipt and storage, fuel breakdown and dissolution, solvent extraction and product concentration and waste management. Results from laboratory and plant corrosion trails are used at the plant design stage to prevent corrosion problems arising. Operational procedures which minimize corrosion if it cannot be prevented at the design stage, are used. (UK)

Carbon Dioxide Corrosion:

DEFF Research Database (Denmark)

Fosbøl, Philip Loldrup

2008-01-01

CO2 corrosion is a general problem in the industry and it is expensive. The focus of this study is an oil gas production related problem. CO2 corrosion is observed in offshore natural gas transportation pipelines. A general overview of the problem is presented in chapter 1. The chemical system...... with the basic thermodynamics of electrolytes in chapter 2, the extension and general description of electrolyte mass transport in chapter 3, and the electrochemical kinetics of corrosion in chapter 4. A literature overview of CO2 corrosion is shown in chapter 5 and possible extensions of the models...... and validated against heat capacity data. The model is also fitted to experimental data produced and shown in chapter 8 for SLE in the Na2CO3-NaHCO3-MEG-H2O system. The application of the above model is shown in chapter 9. Here the thermodynamic correction factors are calculated. These show how the diffusion...

Biotribocorrosion-an appraisal of the time dependence of wear and corrosion interactions: I. The role of corrosion

International Nuclear Information System (INIS)

Yan, Y; Neville, A; Dowson, D

2006-01-01

With the increasing interest in metal-on-metal (MoM) joint implants, studies have been focused on their wear and corrosion behaviour. Integrated electrochemical tests have been conducted and are reported in this paper. The corrosion, wear and wear-corrosion behaviour for three materials (high carbon CoCrMo, low carbon CoCrMo and UNS S31603) have been discussed. Corrosion effects on the overall performance for the three materials are analysed. Two distinct regimes have been found for the three materials: (a) the running-in regime and (b) the steady state regime, in line with other research. Even in the steady state regime, 20%-30% of the material degradation can be attributed to corrosion-related damage. High carbon CoCrMo showed excellent corrosion, wear and corrosion-wear resistance and therefore it delivered the best overall performance in terms of a lower wear rate, a lower friction coefficient and a higher resistance to corrosion

Corrosion inhibitors

International Nuclear Information System (INIS)

El Ashry, El Sayed H.; El Nemr, Ahmed; Esawy, Sami A.; Ragab, Safaa

2006-01-01

The corrosion inhibition efficiencies of some triazole, oxadiazole and thiadiazole derivatives for steel in presence of acidic medium have been studied by using AM1, PM3, MINDO/3 and MNDO semi-empirical SCF molecular orbital methods. Geometric structures, total negative charge on the molecule (TNC), highest occupied molecular energy level (E HOMO ), lowest unoccupied molecular energy level (E LUMO ), core-core repulsion (CCR), dipole moment (μ) and linear solvation energy terms, molecular volume (V i ) and dipolar-polarization (π *), were correlated to corrosion inhibition efficiency. Four equations were proposed to calculate corrosion inhibition efficiency. The agreement with the experimental data was found to be satisfactory; the standard deviations between the calculated and experimental results ranged between ±0.03 and ±4.18. The inhibition efficiency was closely related to orbital energies (E HOMO and E LUMO ) and μ. The correlation between quantum parameters and experimental inhibition efficiency has been validated by single point calculations for the semi-empirical AM1 structures using B3LYP/6-31G** as a higher level of theory. The proposed equations were applied to predict the corrosion inhibition efficiency of some related structures to select molecules of possible activity from a presumable library of compounds

Evaluation of steel corrosion by numerical analysis

OpenAIRE

Kawahigashi, Tatsuo

2017-01-01

Recently, various non-destructive and numerical methods have been used and many cases of steel corrosion are examined. For example, methods of evaluating corrosion through various numerical methods and evaluating macrocell corrosion and micro-cell corrosion using measurements have been proposed. However, there are few reports on estimating of corrosion loss with distinguishing the macro-cell and micro-cell corrosion and with resembling an actuality phenomenon. In this study, for distinguishin...

Corrosion on Mars: An Investigation of Corrosion Mechanisms Under Relevant Simulated Martian Environments

Science.gov (United States)

Calle, Luz M.; Li, Wenyan; Johansen, Michael R.; Buhrow, Jerry W.; Calle, Carlos I.

2017-01-01

This one-year project was selected by NASA's Science Innovation Fund in FY17 to address Corrosion on Mars which is a problem that has not been addressed before. Corrosion resistance is one of the most important properties in selecting materials for landed spacecraft and structures that will support surface operations for the human exploration of Mars. Currently, the selection of materials is done by assuming that the corrosion behavior of a material on Mars will be the same as that on Earth. This is understandable given that there is no data regarding the corrosion resistance of materials in the Mars environment. However, given that corrosion is defined as the degradation of a metal that results from its chemical interaction with the environment, it cannot be assumed that corrosion is going to be the same in both environments since they are significantly different. The goal of this research is to develop a systematic approach to understand corrosion of spacecraft materials on Mars by conducting a literature search of available data, relevant to corrosion in the Mars environment, and by performing preliminary laboratory experiments under relevant simulated Martian conditions. This project was motivated by the newly found evidence for the presence of transient liquid brines on Mars that coincided with the suggestion, by a team of researchers, that some of the structural degradation observed on Curiosity's wheels may be caused by corrosive interactions with the brines, while the most significant damage was attributed to rock scratching. An extensive literature search on data relevant to Mars corrosion confirmed the need for further investigation of the interaction between materials used for spacecraft and structures designed to support long-term surface operations on Mars. Simple preliminary experiments, designed to look at the interaction between an aerospace aluminum alloy (AA7075-T73) and the gases present in the Mars atmosphere, at 20degC and a pressure of 700 Pa

Corrosion Control in the Aerospace Industry

Science.gov (United States)

Calle, Luz Marina; Li, Wenyan; Buhrow, Jerry W.; Johnsey, Marissa N.

2016-01-01

Nearly all metals and their alloys are subject to corrosion that causes them to lose their structural integrity or other critical functionality. It is essential to detect corrosion when it occurs, and preferably at its early stage, so that action can be taken to avoid structural damage or loss of function. Protective coatings are the most commonly used method of corrosion control. However, progressively stricter environmental regulations have resulted in the ban of many commercially available corrosion protective coatings due to the harmful effects of their solvents or corrosion inhibitors. This work concerns the development of a multifunctional, smart coating for the autonomous control of corrosion. This coating is being developed to have the inherent ability to detect the chemical changes associated with the onset of corrosion and respond autonomously to indicate it and control it..

Integration of a thermal stresses supervisory system and useful life of steam turbine rotors; Integracion de un sistema supervisorio de esfuerzos termicos y vida util de rotores de turbinas de vapor

Energy Technology Data Exchange (ETDEWEB)

Carnero, Antonio; Serrano, Luis E. [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); Nebradt, G. Jesus; Leyva, M. Luis [Comision Federal de Electricidad, Mexico, D.F. (Mexico)

2007-11-15

The turbine wheels undergo high thermal and mechanical stresses caused by the requirements of their operation. This causes a mechanical damage (fatigue) that is accumulated according to the frequency whereupon the different operation ways (cold starts, lukewarm or hot) happen. On the other hand, the greater efficiency of power stations of combined cycle with respect to conventional power stations is reflected in a greater production cost of the electrical energy, which has forced to that conventional generation units designed to operate on base load, now are used as variable load units to satisfy the demand during the peak hours. The former, rebounds in a greater frequency of operations of shut downs and hot starts of turbines, reason why the fatigue damage will be increased when changing its operating range. In Mexico turbines there are turbines that have been 15 or 20 years in operation and that do not have a thermal stresses supervisor, reason why when changing their load operation from base load to variable load it is essential to install a rotor supervisor of thermal efforts, with the purpose of limiting or reducing the thermal stresses and in this way reduce the fatigue damage to extend their useful life. The article deals over the integration of a supervisory system of thermal stresses, that from the operation parameters of the turbine, determines the temperature gradient in the labyrinth seals zone between the control passage and the first passage of the high pressure section of the rotor, the thermal and mechanical stresses and the fatigue are calculated, determining the consumption of the useful life for each operation cycle (shutdown and starting). [Spanish] Los rotores de turbina experimentan altas esfuerzos termicos y mecanicos causados por los requerimientos de su operacion. Esto causa un dano mecanico (fatiga) que se acumula de acuerdo a la frecuencia con que los diferentes modos de operacion (arranques en frio, tibio o caliente) suceden. Por otro

The effects of corrosion conditions and cold work on the nodular corrosion of zircaloy-4

International Nuclear Information System (INIS)

You, Gil Sung

1992-02-01

The nodular corrosion of Zircaloy-4 was investigated on the effects of corrosion conditions and cold work. Variation of steam pressures, heat-up environments and prefilms were considered and cold work effects were also studied. The corrosion rate of Zircaloy-4 was dependent on pressure between 1 and 100 atm and it followed the cubic law as W=16.85 x P 0.31 for plate specimens and W=12.69 x P 0.27 for tube specimens, where W is weight gain (mg/dm 2 ) and P is the steam pressure (atm). The environment variation in autoclave during heat-up period did not affect the early stage of nodular corrosion. The prefilm, which was formed at 500 .deg. C under 1 atm steam for 4 hours, restrained the formation of the initial small nodules. The oxide film formed under 1 atm steam showed no difference of electrical resistivity from the oxides formed under 100 atm steam pressure. Cold work specimens showed the higher resistivity against nodular corrosion than as-received specimens. The corrosion resistance arising from cold work seems to be due to the texture changes by the cold work. The results showed that cold work can affect the later stage of uniform corrosion and the early stage of nodular corrosion, namely, the nodule initiation stage

Experiments and models of general corrosion and flow-assisted corrosion of materials in nuclear reactor environments

Science.gov (United States)

Cook, William Gordon

Corrosion and material degradation issues are of concern to all industries. However, the nuclear power industry must conform to more stringent construction, fabrication and operational guidelines due to the perceived additional risk of operating with radioactive components. Thus corrosion and material integrity are of considerable concern for the operators of nuclear power plants and the bodies that govern their operations. In order to keep corrosion low and maintain adequate material integrity, knowledge of the processes that govern the material's breakdown and failure in a given environment are essential. The work presented here details the current understanding of the general corrosion of stainless steel and carbon steel in nuclear reactor primary heat transport systems (PHTS) and examines the mechanisms and possible mitigation techniques for flow-assisted corrosion (FAC) in CANDU outlet feeder pipes. Mechanistic models have been developed based on first principles and a 'solution-pores' mechanism of metal corrosion. The models predict corrosion rates and material transport in the PHTS of a pressurized water reactor (PWR) and the influence of electrochemistry on the corrosion and flow-assisted corrosion of carbon steel in the CANDU outlet feeders. In-situ probes, based on an electrical resistance technique, were developed to measure the real-time corrosion rate of reactor materials in high-temperature water. The probes were used to evaluate the effects of coolant pH and flow on FAC of carbon steel as well as demonstrate of the use of titanium dioxide as a coolant additive to mitigated FAC in CANDU outlet feeder pipes.

Desafío con wssv bajo fluctuaciones de temperatura

OpenAIRE

Sonnenholzner, Stanislaus

2002-01-01

Desafío con WSSV bajo fluctuaciones de temperatura En trabajos anteriores sobre el efecto de la temperatura del agua sobre la supervivencia del camarón infectado con el virus de la Mancha Blanca, se demostró que una temperatura constante de 33ºC por 8 días genera una respuesta inmune en el camarón correlacionada a una supervivencia superior al 90%, lo cual se tradujo posteriormente en una propuesta práctica de cultivo de camarón en estanques con invernaderos, actualmente en evaluación e...

Corrosion test by low-temperature coal tar

Energy Technology Data Exchange (ETDEWEB)

Ando, S; Yamamoto, S

1952-01-01

Corrosive actions of various fractions of low-temperature coal tar against mild steel or Cr 13-steel were compared at their boiling states. Corrosions became severe when the boiling points exceeded 240/sup 0/. The acidic fractions were more corrosive. In all instances, corrosion was excessive at the beginning of immersion testing and then gradually became mild; boiling accelerated the corrosion. Cr 13-steel was corrosion-resistant to low-temperature coal-tar fractions.

Electrochemical characterisation speeds up prediction of corrosion behaviour

Energy Technology Data Exchange (ETDEWEB)

Schuring, E.W.; Hooijmans, J.W. [ECN Environment and Energy Engineering, Petten (Netherlands)

2013-04-15

The contents of this presentation show the following elements: Introduction; Corrosion in real life; Why Electrochemical characterisation of corrosion; Applications (corrosion resistance coatings, corrosion behaviour (brazed) joints); Available electrochemical corrosion techniques; Standards; Conclusions. In the Conclusions the corrosion screening method is summarized: ECN method fast; within 1h -1 week results depending on test method; Fast pre-selection of promising materials/combinations (cost savings); Determining of corrosion initiation; Determination of corrosion mechanisms and propagation; Life time predictions possible; Strong combination with metallographic post-investigation; Ranking materials / constructions for corrosion performance.

Microencapsulation Technology for Corrosion Mitigation by Smart Coatings

Science.gov (United States)

Buhrow, Jerry; Li, Wenyan; Jolley, Scott; Calle, Luz M.

2011-01-01

A multifunctional, smart coating for the autonomous control of corrosion is being developed based on micro-encapsulation technology. Corrosion indicators as well as corrosion inhibitors have been incorporated into microcapsules, blended into several paint systems, and tested for corrosion detection and protection effectiveness. This paper summarizes the development, optimization, and testing of microcapsules specifically designed to be incorporated into a smart coating that will deliver corrosion inhibitors to mitigate corrosion autonomously. Key words: smart coating, corrosion inhibition, microencapsulation, microcapsule, pH sensitive microcapsule, corrosion inhibitor, corrosion protection pain

Characterization of Corrosion Products on Carbon Steel Exposed to Natural Weathering and to Accelerated Corrosion Tests

Directory of Open Access Journals (Sweden)

Renato Altobelli Antunes

2014-01-01

Full Text Available The aim of this work was to compare the corrosion products formed on carbon steel plates submitted to atmospheric corrosion in urban and industrial atmospheres with those formed after accelerated corrosion tests. The corrosion products were characterized by X-ray diffraction, Mössbauer spectroscopy, and Raman spectroscopy. The specimens were exposed to natural weathering in both atmospheres for nine months. The morphologies of the corrosion products were evaluated using scanning electron microscopy. The main product found was lepidocrocite. Goethite and magnetite were also found on the corroded specimens but in lower concentrations. The results showed that the accelerated test based on the ASTM B117 procedure presented poor correlation with the atmospheric corrosion tests whereas an alternated fog/dry cycle combined with UV radiation exposure provided better correlation.

49 CFR 172.442 - CORROSIVE label.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false CORROSIVE label. 172.442 Section 172.442... SECURITY PLANS Labeling § 172.442 CORROSIVE label. (a) Except for size and color, the CORROSIVE label must... CORROSIVE label must be white in the top half and black in the lower half. [Amdt. 172-123, 56 FR 66259, Dec...

Emerging Corrosion Inhibitors for Interfacial Coating

Directory of Open Access Journals (Sweden)

Mona Taghavikish

2017-12-01

Full Text Available Corrosion is a deterioration of a metal due to reaction with environment. The use of corrosion inhibitors is one of the most effective ways of protecting metal surfaces against corrosion. Their effectiveness is related to the chemical composition, their molecular structures and affinities for adsorption on the metal surface. This review focuses on the potential of ionic liquid, polyionic liquid (PIL and graphene as promising corrosion inhibitors in emerging coatings due to their remarkable properties and various embedment or fabrication strategies. The review begins with a precise description of the synthesis, characterization and structure-property-performance relationship of such inhibitors for anti-corrosion coatings. It establishes a platform for the formation of new generation of PIL based coatings and shows that PIL corrosion inhibitors with various heteroatoms in different form can be employed for corrosion protection with higher barrier properties and protection of metal surface. However, such study is still in its infancy and there is significant scope to further develop new structures of PIL based corrosion inhibitors and coatings and study their behaviour in protection of metals. Besides, it is identified that the combination of ionic liquid, PIL and graphene could possibly contribute to the development of the ultimate corrosion inhibitor based coating.

A STUDY OF CORROSION AND STRESS CORROSION CRACKING OF CARBON STEEL NUCLEAR WASTE STORAGE TANKS

International Nuclear Information System (INIS)

BOOMER, K.D.

2007-01-01

The Hanford reservation Tank Farms in Washington State has 177 underground storage tanks that contain approximately 50 million gallons of liquid legacy radioactive waste from cold war plutonium production. These tanks will continue to store waste until it is treated and disposed. These nuclear wastes were converted to highly alkaline pH wastes to protect the carbon steel storage tanks from corrosion. However, the carbon steel is still susceptible to localized corrosion and stress corrosion cracking. The waste chemistry varies from tank to tank, and contains various combinations of hydroxide, nitrate, nitrite, chloride, carbonate, aluminate and other species. The effect of each of these species and any synergistic effects on localized corrosion and stress corrosion cracking of carbon steel have been investigated with electrochemical polarization, slow strain rate, and crack growth rate testing. The effect of solution chemistry, pH, temperature and applied potential are all considered and their role in the corrosion behavior will be discussed

Microencapsulation of Corrosion Indicators for Smart Coatings

Science.gov (United States)

Li, Wenyan; Buhrow, Jerry W.; Jolley, Scott T.; Calle, Luz M.; Hanna,Joshua S.; Rawlins, James W.

2011-01-01

A multifunctional smart coating for the autonomous detection, indication, and control of corrosion is been developed based on microencapsulation technology. This paper summarizes the development, optimization, and testing of microcapsules specifically designed for early detection and indication of corrosion when incorporated into a smart coating. Results from experiments designed to test the ability of the microcapsules to detect and indicate corrosion, when blended into several paint systems, show that these experimental coatings generate a color change, indicative of spot specific corrosion events, that can be observed with the naked eye within hours rather than the hundreds of hours or months typical of the standard accelerated corrosion test protocols.. Key words: smart coating, corrosion detection, microencapsulation, microcapsule, pH-sensitive microcapsule, corrosion indicator, corrosion sensing paint

Condiciones de trabajo materno y bajo peso al nacer en la Ciudad de México

Directory of Open Access Journals (Sweden)

PRUDENCIA CERÓN-MIRELES

1997-01-01

Full Text Available Objetivo. Estudiar la asociación entre condiciones de trabajo materno y bajo peso al nacer en la Ciudad de México. Material y métodos. Se encuestaron 2 623 trabajadoras que atendieron sus partos en tres grandes hospitales de la Ciudad de México en 1992. Se obtuvo información sobre los principales factores biológicos y sociales que se asocian al bajo peso al nacer; asimismo, se determinó el estrés ocupacional utilizando el instrumento desarrollado por Karasek. Se utilizaron modelos de regresión logística para evaluar la relación de las condiciones de trabajo con el bajo peso al nacer, controlando por variables confusoras. Resultados. El bajo peso al nacer fue más alto en trabajadoras con jornadas mayores a 50 horas semanales (RM= 1.6; IC= 1.17, 2.28 y con conflictos laborales (RM= 1.5; IC= 1.0, 2.25. La falta de apoyo social tangible fue identificado como un factor de riesgo de bajo peso al nacer (RM= 1.7; IC= 1.20, 2.33. Las medidas preventivas laborales como el cambio de tareas, disminución de la jornada y las salidas por enfermedad no mostraron un efecto benéfico en el peso al nacer, a excepción de la licencia de maternidad; las madres que no la tuvieron mostraron una probabilidad 2.2 veces mayor para bajo peso al nacer (IC= 1.66, 2.93. Conclusiones. Estos hallazgos resaltan la importancia de identificar los factores de riesgo ocupacional en el embarazo..Objective. To study the association between maternal working conditions and low birth-weight in Mexico City. Material and methods. Interviews of 2 623 workers who gave birth in Mexico City hospitals during 1992 were analyzed. Information on the main biologic and social factors associated to low birth-weight was registered. Occupational stress was determined with the instrument designed by Karasek. Logistic regression models to evaluate the relationship between working conditions and low birth-weight were used, controlling by confounding variables. Results. Low birth-weight was

Scanning reference electrode techniques in localized corrosion

International Nuclear Information System (INIS)

Isaacs, H.S.; Vyas, B.

1979-04-01

The principles, advantages, and implementations of scanning reference electrode techniques are reviewed. Data related to pitting, intergranular corrosion, welds and stress corrosion cracking are presented. The technique locates the position of localized corrosion and can be used to monitor the development of corrosion and changes in the corrosion rate under a wide range of conditions

Accelerated Stress-Corrosion Testing

Science.gov (United States)

1986-01-01

Test procedures for accelerated stress-corrosion testing of high-strength aluminum alloys faster and provide more quantitative information than traditional pass/fail tests. Method uses data from tests on specimen sets exposed to corrosive environment at several levels of applied static tensile stress for selected exposure times then subsequently tensile tested to failure. Method potentially applicable to other degrading phenomena (such as fatigue, corrosion fatigue, fretting, wear, and creep) that promote development and growth of cracklike flaws within material.

Aspects of high temperature corrosion of boiler tubes

Energy Technology Data Exchange (ETDEWEB)

Spiegel, M.; Bendick, W. [Salzgitter-Mannesmann-Forschung GmbH, Duisburg (Germany)

2008-07-01

The development of new boiler steels for power generation has to consider significant creep strength as well as oxidation and corrosion resistance. High temperature corrosion of boiler materials concerns steam oxidation as well as fireside corrosion of parts, in contact with the flue gas. It will be shown that depending on the quality of the fuel, especially chlorine and sulphur are responsible for most of the fireside corrosion problems. Corrosion mechanisms will be presented for flue gas induced corrosion (HCl) and deposit induced corrosion (chlorides and sulfates). Especially for the 700 C technology, deposit induced corrosion issues have to be considered and the mechanisms of corrosion by molten sulfates 'Hot Corrosion' will be explained. Finally, an overview will be given on the selection of suitable materials in order to minimise corrosion relates failures. (orig.)

Corrosion strength monitoring of NPP component residual lifetime

International Nuclear Information System (INIS)

Denisov, V.G.; Belous, V.N.; Arzhaev, A.I.; Shuvalov, V.A.

1994-01-01

Importance of corrosion and fatigue monitoring; types of corrosion determine the NPP equipment life; why automated on-line corrosion and fatigue monitoring is preferable; major stages of lifetime monitoring system development; major groups of sensors for corrosion and strength monitoring system; high temperature on-line monitoring of water chemistry and corrosion; the RBMK-1000 NPP unit automatic water chemistry and corrosion monitoring scheme; examples of pitting, crevice and general corrosion forecast calculations on the basis of corrosion monitoring data; scheme of an experimental facility for water chemistry and corrosion monitoring sensor testing. 2 figs., 4 tabs

Influence of temperature on corrosion rate and porosity of corrosion products of carbon steel in anoxic bentonite environment

International Nuclear Information System (INIS)

Stoulil, J.; Kaňok, J.; Kouřil, M.; Parschová, H.; Novák, P.

2013-01-01

Highlights: •The corrosion rate is not significantly dependent on temperature. •Corrosion products at higher temperatures have different color. •Corrosion products at higher temperatures are more compact. •The change in corrosion products nature is reversible. -- Abstract: The study focuses on the porosity of layers of corrosion products and its impact on corrosion rate of carbon steel in moist bentonite. Measurements were performed in an aggressive Czech type of bentonite – Rokle B75 at temperatures of 90 and 40 °C. Aggressiveness of B75 bentonite consists in low content of chlorides. Presence of chlorides in pore solution allows formation of more protective magnetite. The evaluation was made by electrochemical techniques (red/ox potential, open circuit potential, linear polarization resistance, impedance spectroscopy) and resistometric sensor measurements. The result imply that the higher the temperature the more compact is the layer of corrosion products that slightly decelerates corrosion rate compared to the state at 40 °C. The state of corrosion products at both temperatures is reversible

Influence of temperature on corrosion rate and porosity of corrosion products of carbon steel in anoxic bentonite environment

Energy Technology Data Exchange (ETDEWEB)

Stoulil, J., E-mail: jan.stoulil@vscht.cz [Department of Metals and Corrosion Engineering, Institute of Chemical Technology, Prague (Czech Republic); Kaňok, J.; Kouřil, M. [Department of Metals and Corrosion Engineering, Institute of Chemical Technology, Prague (Czech Republic); Parschová, H. [Department of Power Engineering, Institute of Chemical Technology, Prague (Czech Republic); Novák, P. [Department of Metals and Corrosion Engineering, Institute of Chemical Technology, Prague (Czech Republic)

2013-11-15

Highlights: •The corrosion rate is not significantly dependent on temperature. •Corrosion products at higher temperatures have different color. •Corrosion products at higher temperatures are more compact. •The change in corrosion products nature is reversible. -- Abstract: The study focuses on the porosity of layers of corrosion products and its impact on corrosion rate of carbon steel in moist bentonite. Measurements were performed in an aggressive Czech type of bentonite – Rokle B75 at temperatures of 90 and 40 °C. Aggressiveness of B75 bentonite consists in low content of chlorides. Presence of chlorides in pore solution allows formation of more protective magnetite. The evaluation was made by electrochemical techniques (red/ox potential, open circuit potential, linear polarization resistance, impedance spectroscopy) and resistometric sensor measurements. The result imply that the higher the temperature the more compact is the layer of corrosion products that slightly decelerates corrosion rate compared to the state at 40 °C. The state of corrosion products at both temperatures is reversible.

High temperature corrosion during biomass firing: improved understanding by depth resolved characterisation of corrosion products

DEFF Research Database (Denmark)

Okoro, Sunday Chukwudi; Montgomery, Melanie; Jappe Frandsen, Flemming

2015-01-01

changes within the near surface region (covering both the deposit and the steel surface). Such cross-section analysis was further complemented by plan view investigations (additionally involving X-ray diffraction) combined with removal of the corrosion products. Improved insights into the nature......The high temperature corrosion of an austenitic stainless steel (TP 347H FG), widely utilised as a superheater tube material in Danish power stations, was investigated to verify the corrosion mechanisms related to biomass firing. KCl coated samples were exposed isothermally to 560 degrees C...... of the corrosion products as a function of distance from the deposit surface were revealed through this comprehensive characterisation. Corrosion attack during simulated straw-firing conditions was observed to occur through both active oxidation and sulphidation mechanisms....

Corrosion measurement using flux gate magnetometer

International Nuclear Information System (INIS)

Rashdi Shah Ahmad; Chong Cheong Wei

2001-01-01

The ability of fluxgate magnetometer to detect and measure quantitatively the magnetic field generated by electrochemical corrosion is presented. In this study, each sample (iron plate) was exposed to a range of increasingly corrosive environment. During the exposure, we measured the magnetic field above the sample for specific duration of time. The result shows that there is a clear relationship between corrosivity of the environment and the change in magnitude of magnetic field that was generated by the corrosion reaction. Therefore, the measurement of magnetic field might be used to determine the corrosion rates. (Author)

Nodular Corrosion Characteristics of Zirconium Alloys

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyun Gil; Jeong, Y. H.; Park, S. Y.; Lee, D. J

2003-01-15

This study was reported the effect of the nodular corrosion on the nuclear reactor environmental along with metallurgical influence, also suggested experimental scheme related to evaluate nodular corrosion characteristics of Zr-1 Nb alloy. Remedial strategies against the nodular corrosion should firstly develop plan to assess the effect of the water quality condition (Oxygen, Hydrogen) as well as the boiling on the nodular corrosion, secondarily establish plan to control heat treatment process to keep a good resistance on nodular corrosion in Zr-1Nb alloy as former western reactor did.

Measurement of weak magnetic field of corrosion current of isolated corrosion center

Directory of Open Access Journals (Sweden)

I. V. Bardin

2015-01-01

Full Text Available A very small magnetic field of corrosion current, of the order of 10−4 Oe, generated by isolated zinc inclusion in a copper platelet placed in electrolyte has been measured for the first time with a highly sensitive giant magneto-impedance magnetometer. The total corrosion current of the inclusion is estimated comparing the measured magnetic field distribution with corresponding theoretical calculation. The estimated value of the total corrosion current turns out to be in reasonable agreement with that one obtained in the standard gravimetric measurement.

Rhenium corrosion in chloride melts

International Nuclear Information System (INIS)

Stepanov, A.D.; Shkol'nikov, S.N.; Vetyukov, M.M.

1989-01-01

The results investigating rhenium corrosion in chloride melts containing sodium, potassium and chromium ions by a gravimetry potentials in argon atmosphere in a sealing quarth cell are described. Rhenium corrosion is shown to be rather considerable in melts containing CrCl 2 . The value of corrosion rate depending on temperature is determined

Stochastic process corrosion growth models for pipeline reliability

International Nuclear Information System (INIS)

Bazán, Felipe Alexander Vargas; Beck, André Teófilo

2013-01-01

Highlights: •Novel non-linear stochastic process corrosion growth model is proposed. •Corrosion rate modeled as random Poisson pulses. •Time to corrosion initiation and inherent time-variability properly represented. •Continuous corrosion growth histories obtained. •Model is shown to precisely fit actual corrosion data at two time points. -- Abstract: Linear random variable corrosion models are extensively employed in reliability analysis of pipelines. However, linear models grossly neglect well-known characteristics of the corrosion process. Herein, a non-linear model is proposed, where corrosion rate is represented as a Poisson square wave process. The resulting model represents inherent time-variability of corrosion growth, produces continuous growth and leads to mean growth at less-than-one power of time. Different corrosion models are adjusted to the same set of actual corrosion data for two inspections. The proposed non-linear random process corrosion growth model leads to the best fit to the data, while better representing problem physics

Corrosion-Resistant High-Entropy Alloys: A Review

Directory of Open Access Journals (Sweden)

Yunzhu Shi

2017-02-01

Full Text Available Corrosion destroys more than three percent of the world’s gross domestic product. Therefore, the design of highly corrosion-resistant materials is urgently needed. By breaking the classical alloy-design philosophy, high-entropy alloys (HEAs possess unique microstructures, which are solid solutions with random arrangements of multiple elements. The particular locally-disordered chemical environment is expected to lead to unique corrosion-resistant properties. In this review, the studies of the corrosion-resistant HEAs during the last decade are summarized. The corrosion-resistant properties of HEAs in various aqueous environments and the corrosion behavior of HEA coatings are presented. The effects of environments, alloying elements, and processing methods on the corrosion resistance are analyzed in detail. Furthermore, the possible directions of future work regarding the corrosion behavior of HEAs are suggested.

Spatial distribution of crystalline corrosion products formed during corrosion of stainless steel in concrete

Energy Technology Data Exchange (ETDEWEB)

Serdar, Marijana [Department of Materials, Faculty of Civil Engineering, University of Zagreb, 10000 Zagreb (Croatia); Meral, Cagla [Middle East Technical University, Department of Civil Engineering, Ankara (Turkey); Kunz, Martin [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Bjegovic, Dubravka [Department of Materials, Faculty of Civil Engineering, University of Zagreb, 10000 Zagreb (Croatia); Wenk, Hans-Rudolf [Department of Earth and Planetary Science, University of California, Berkeley, CA 94720 (United States); Monteiro, Paulo J.M., E-mail: monteiro@ce.berkeley.edu [Department of Civil and Environmental Engineering, University of California, Berkeley, CA 94720 (United States)

2015-05-15

The mineralogy and spatial distribution of nano-crystalline corrosion products that form in the steel/concrete interface were characterized using synchrotron X-ray micro-diffraction (μ-XRD). Two types of low-nickel high-chromium reinforcing steels embedded into mortar and exposed to NaCl solution were investigated. Corrosion in the samples was confirmed by electrochemical impedance spectroscopy (EIS). μ-XRD revealed that goethite (α-FeOOH) and akaganeite (β-FeOOH) are the main iron oxide–hydroxides formed during the chloride-induced corrosion of stainless steel in concrete. Goethite is formed closer to the surface of the steel due to the presence of chromium in the steel, while akaganeite is formed further away from the surface due to the presence of chloride ions. Detailed microstructural analysis is shown and discussed on one sample of each type of steel. - Highlights: • Synchrotron micro-diffraction used to map the distribution of crystalline phases. • Goethite and akaganeite are the main corrosion products during chloride induced corrosion in mortar. • Layers of goethite and akaganeite are negatively correlated. • EDS showed Cr present in corrosion products identified by SEM.

Spatial distribution of crystalline corrosion products formed during corrosion of stainless steel in concrete

International Nuclear Information System (INIS)

Serdar, Marijana; Meral, Cagla; Kunz, Martin; Bjegovic, Dubravka; Wenk, Hans-Rudolf; Monteiro, Paulo J.M.

2015-01-01

The mineralogy and spatial distribution of nano-crystalline corrosion products that form in the steel/concrete interface were characterized using synchrotron X-ray micro-diffraction (μ-XRD). Two types of low-nickel high-chromium reinforcing steels embedded into mortar and exposed to NaCl solution were investigated. Corrosion in the samples was confirmed by electrochemical impedance spectroscopy (EIS). μ-XRD revealed that goethite (α-FeOOH) and akaganeite (β-FeOOH) are the main iron oxide–hydroxides formed during the chloride-induced corrosion of stainless steel in concrete. Goethite is formed closer to the surface of the steel due to the presence of chromium in the steel, while akaganeite is formed further away from the surface due to the presence of chloride ions. Detailed microstructural analysis is shown and discussed on one sample of each type of steel. - Highlights: • Synchrotron micro-diffraction used to map the distribution of crystalline phases. • Goethite and akaganeite are the main corrosion products during chloride induced corrosion in mortar. • Layers of goethite and akaganeite are negatively correlated. • EDS showed Cr present in corrosion products identified by SEM

The dual role of microbes in corrosion.

Science.gov (United States)

Kip, Nardy; van Veen, Johannes A

2015-03-01

Corrosion is the result of a series of chemical, physical and (micro) biological processes leading to the deterioration of materials such as steel and stone. It is a world-wide problem with great societal and economic consequences. Current corrosion control strategies based on chemically produced products are under increasing pressure of stringent environmental regulations. Furthermore, they are rather inefficient. Therefore, there is an urgent need for environmentally friendly and sustainable corrosion control strategies. The mechanisms of microbially influenced corrosion and microbially influenced corrosion inhibition are not completely understood, because they cannot be linked to a single biochemical reaction or specific microbial species or groups. Corrosion is influenced by the complex processes of different microorganisms performing different electrochemical reactions and secreting proteins and metabolites that can have secondary effects. Information on the identity and role of microbial communities that are related to corrosion and corrosion inhibition in different materials and in different environments is scarce. As some microorganisms are able to both cause and inhibit corrosion, we pay particular interest to their potential role as corrosion-controlling agents. We show interesting interfaces in which scientists from different disciplines such as microbiology, engineering and art conservation can collaborate to find solutions to the problems caused by corrosion.

The dual role of microbes in corrosion

Science.gov (United States)

Kip, Nardy; van Veen, Johannes A

2015-01-01

Corrosion is the result of a series of chemical, physical and (micro) biological processes leading to the deterioration of materials such as steel and stone. It is a world-wide problem with great societal and economic consequences. Current corrosion control strategies based on chemically produced products are under increasing pressure of stringent environmental regulations. Furthermore, they are rather inefficient. Therefore, there is an urgent need for environmentally friendly and sustainable corrosion control strategies. The mechanisms of microbially influenced corrosion and microbially influenced corrosion inhibition are not completely understood, because they cannot be linked to a single biochemical reaction or specific microbial species or groups. Corrosion is influenced by the complex processes of different microorganisms performing different electrochemical reactions and secreting proteins and metabolites that can have secondary effects. Information on the identity and role of microbial communities that are related to corrosion and corrosion inhibition in different materials and in different environments is scarce. As some microorganisms are able to both cause and inhibit corrosion, we pay particular interest to their potential role as corrosion-controlling agents. We show interesting interfaces in which scientists from different disciplines such as microbiology, engineering and art conservation can collaborate to find solutions to the problems caused by corrosion. PMID:25259571

A New Corrosion Sensor to Determine the Start and Development of Embedded Rebar Corrosion Process at Coastal Concrete

Directory of Open Access Journals (Sweden)

Weiliang Jin

2013-09-01

Full Text Available The corrosion of reinforcements induced by chloride has resulted to be one of the most frequent causes of their premature damage. Most corrosion sensors were designed to monitor corrosion state in concrete, such as Anode-Ladder-System and Corrowatch System, which are widely used to monitor chloride ingress in marine concrete. However, the monitoring principle of these corrosion sensors is based on the macro-cell test method, so erroneous information may be obtained, especially from concrete under drying or saturated conditions due to concrete resistance taking control in macro-cell corrosion. In this paper, a fast weak polarization method to test corrosion state of reinforcements based on electrochemical polarization dynamics was proposed. Furthermore, a new corrosion sensor for monitoring the corrosion state of concrete cover was developed based on the proposed test method. The sensor was tested in cement mortar, with dry-wet cycle tests to accelerate the chloride ingress rate. The results show that the corrosion sensor can effectively monitor chloride penetration into concrete with little influence of the relative humidity in the concrete. With a reasonable corrosion sensor electrode arrangement, it seems the Ohm-drop effect measured by EIS can be ignored, which makes the tested electrochemical parameters more accurate.

A new corrosion sensor to determine the start and development of embedded rebar corrosion process at coastal concrete.

Science.gov (United States)

Xu, Chen; Li, Zhiyuan; Jin, Weiliang

2013-09-30

The corrosion of reinforcements induced by chloride has resulted to be one of the most frequent causes of their premature damage. Most corrosion sensors were designed to monitor corrosion state in concrete, such as Anode-Ladder-System and Corrowatch System, which are widely used to monitor chloride ingress in marine concrete. However, the monitoring principle of these corrosion sensors is based on the macro-cell test method, so erroneous information may be obtained, especially from concrete under drying or saturated conditions due to concrete resistance taking control in macro-cell corrosion. In this paper, a fast weak polarization method to test corrosion state of reinforcements based on electrochemical polarization dynamics was proposed. Furthermore, a new corrosion sensor for monitoring the corrosion state of concrete cover was developed based on the proposed test method. The sensor was tested in cement mortar, with dry-wet cycle tests to accelerate the chloride ingress rate. The results show that the corrosion sensor can effectively monitor chloride penetration into concrete with little influence of the relative humidity in the concrete. With a reasonable corrosion sensor electrode arrangement, it seems the Ohm-drop effect measured by EIS can be ignored, which makes the tested electrochemical parameters more accurate.

Corrosion engineering in nuclear power industry

International Nuclear Information System (INIS)

Prazak, M.; Tlamsa, J.; Jirousova, D.; Silber, K.

1990-01-01

Corrosion problems in nuclear power industry are discussed from the point of view of anticorrosion measures, whose aim is not only increasing the lifetime of the equipment but, first of all, securing ecological safety. A brief description is given of causes of corrosion damage that occurred at Czechoslovak nuclear power plants and which could have been prevented. These involve the corrosion of large-volume radioactive waste tanks made of the CSN 17247 steel and of waste piping of an ion exchange station made of the same material, a crack in a steam generator collector, contamination of primary circuit water with iron, and corrosion of CrNi corrosion-resistant steel in a spent fuel store. It is concluded that if a sufficient insight into the corrosion relationships exists and a reasonable volume of data is available concerning the corrosion state during the nuclear facility performance, the required safety can be achieved without adopting extremely costly anticorrosion measures. (Z.M.)

High temperature corrosion of metals

International Nuclear Information System (INIS)

Quadakkers, W.J.; Schuster, H.; Ennis, P.J.

1988-08-01

This paper covers three main topics: 1. high temperature oxidation of metals and alloys, 2. corrosion in sulfur containing environments and 3. structural changes caused by corrosion. The following 21 subjects are discussed: Influence of implanted yttrium and lanthanum on the oxidation behaviour of beta-NiA1; influence of reactive elements on the adherence and protective properties of alumina scales; problems related to the application of very fine markers in studying the mechanism of thin scale formation; oxidation behaviour of chromia forming Co-Cr-Al alloys with or without reactive element additions; growth and properties of chromia-scales on high-temperature alloys; quantification of the depletion zone in high temperature alloys after oxidation in process gas; effects of HC1 and of N2 in the oxidation of Fe-20Cr; investigation under nuclear safety aspects of Zircaloy-4 oxidation kinetics at high temperatures in air; on the sulfide corrosion of metallic materials; high temperature sulfide corrosion of Mn, Nb and Nb-Si alloys; corrosion behaviour or NiCrAl-based alloys in air and air-SO2 gas mixtures; sulfidation of cobalt at high temperatures; preoxidation for sulfidation protection; fireside corrosion and application of additives in electric utility boilers; transport properties of scales with complex defect structures; observations of whiskers and pyramids during high temperature corrosion of iron in SO2; corrosion and creep of alloy 800H under simulated coal gasification conditions; microstructural changes of HK 40 cast alloy caused by exploitation in tubes in steam reformer installation; microstructural changes during exposure in corrosive environments and their effect on mechanical properties; coatings against carburization; mathematical modeling of carbon diffusion and carbide precipitation in Ni-Cr-based alloys. (MM)

Evaluation of corrosion products formed by sulfidation as inhibitors of the naphthenic corrosion of AISI-316 steel

Science.gov (United States)

Sanabria-Cala, J. A.; Montañez, N. D.; Laverde Cataño, D.; Y Peña Ballesteros, D.; Mejía, C. A.

2017-12-01

Naphthenic acids present in oil from most regions worldwide currently stand as the main responsible for the naphthenic corrosion problems, affecting the oil-refining industry. The phenomenon of sulfidation, accompanying corrosion processes brought about by naphthenic acids in high-temperature refining plant applications, takes place when the combination of sulfidic acid (H2S) with Fe forms layers of iron sulphide (FeS) on the material surface, layers with the potential to protect the material from attack by other corrosive species like naphthenic acids. This work assessed corrosion products formed by sulfidation as inhibitors of naphthenic corrosion rate in AISI-316 steel exposed to processing conditions of simulated crude oil in a dynamic autoclave. Calculation of the sulfidation and naphthenic corrosion rates were determined by gravimetry. The surfaces of the AISI-316 gravimetric coupons exposed to acid systems; were characterized morphologically by X-Ray Diffraction (XRD) and X-ray Fluorescence by Energy Dispersive Spectroscopy (EDS) combined with Scanning Electron Microscopy (SEM). One of the results obtained was the determination of an inhibiting effect of corrosion products at 250 and 300°C, where lower corrosion rate levels were detected. For the temperature of 350°C, naphthenic corrosion rates increased due to deposition of naphthenic acids on the areas where corrosion products formed by sulfidation have lower homogeneity and stability on the surface, thus accelerating the destruction of AISI-316 steel. The above provides an initial contribution to oil industry in search of new alternatives to corrosion control by the attack of naphthenic acids, from the formation of FeS layers on exposed materials in the processing of heavy crude oils with high sulphur content.

Downhole corrosion mechanisms and mitigation strategies

Energy Technology Data Exchange (ETDEWEB)

McDougall, D. [Baker Hughes Canada, Calgary, AB (Canada)

2010-07-01

Pipeline corrosion refers to its deterioration because of a reaction with its environment. Although the physical condition of the metal at the anode initiates the corrosion process, it is the chemistry and composition of the electrolyte that controls the rate of the corrosion reaction and the severity of the corrosion. This presentation described the role of corrosion rate accelerators, with particular reference to dissolved gases such as oxygen, hydrogen sulfides and carbon dioxide, as well as pH levels, salinity, flow rate, temperature and presence of solids such as iron sulfides and sulfur. The effects of these accelerators were shown to be additive. Mitigation strategies include using materials such as resistant metal alloys or fiberglass, and applying coatings and chemical inhibitors. The importance of corrosion monitoring was also emphasized, with particular reference to the value of examining the number of corrosion related failures that have occurred over a fixed period of time. It was concluded that the ability to analyze samples of failed materials results in a better understanding of the cause of the failure, and is an integral part of designing any successful corrosion control program. tabs., figs.

Corrosion of Carbon Steel and Corrosion-Resistant Rebars in Concrete Structures Under Chloride Ion Attack

Science.gov (United States)

Mohamed, Nedal; Boulfiza, Mohamed; Evitts, Richard

2013-03-01

Corrosion of reinforced concrete is the most challenging durability problem that threatens reinforced concrete structures, especially structures that are subject to severe environmental conditions (i.e., highway bridges, marine structures, etc.). Corrosion of reinforcing steel leads to cracking and spalling of the concrete cover and billions of dollars are spent every year on repairing such damaged structures. New types of reinforcements have been developed to avoid these high-cost repairs. Thus, it is important to study the corrosion behavior of these new types of reinforcements and compare them to the traditional carbon steel reinforcements. This study aimed at characterizing the corrosion behavior of three competing reinforcing steels; conventional carbon steel, micro-composite steel (MMFX-2) and 316LN stainless steel, through experiments in carbonated and non-carbonated concrete exposed to chloride-laden environments. Synthetic pore water solutions have been used to simulate both cases of sound and carbonated concrete under chloride ions attack. A three-electrode corrosion cell is used for determining the corrosion characteristics and rates. Multiple electrochemical techniques were applied using a Gamry PC4™ potentiostat manufactured by Gamry Instruments (Warminster, PA). DC corrosion measurements were applied on samples subjected to fixed chloride concentration in the solution.

Corrosion problems of PWR steam generators

International Nuclear Information System (INIS)

Urbancik, L.; Kostal, M.

Literature data are assessed on corrosion failures of steam generator tubes made of INCONEL 600 or INCOLOY 800. It was found that both alloys with high nickel content showed good stability in a corrosion environment while being sensitive to carbide formation on grain boundaries. The gradual depletion of chromium results from the material and corrosion resistance deteriorates. INCOLOY 800 whose chromium carbide precipitation on grain boundaries in pure water and steam is negligible up to 75O degC and which is not subject to corrosion attacks in the above media and in an oxidizing environment at a temperature to about 700 degC shows the best corrosion resistance. Its favourable properties were tested in long-term operation in the Peach Bottom 1 nuclear power plant where no failures due to corrosion of this material have been recorded since 1967. In view of oxygenic-acid surface corrosion, it is necessary to work in a neutral or slightly basic environment should any one of the two alloys be used for steam generator construction. The results are summed up of an analysis conducted for the Beznau I NOK reactor. Water treatment with ash-free amines can be used as prevention against chemical corrosion mechanisms, although the treatment itself does not ensure corrosion resistance of steam generator key components. (J.B.)

Boric Acid Corrosion of Concrete Rebar

Directory of Open Access Journals (Sweden)

Yang L.

2013-07-01

Full Text Available Borated water leakage through spent fuel pools (SFPs at pressurized water reactors is a concern because it could cause corrosion of reinforcement steel in the concrete structure and compromise the integrity of the structure. Because corrosion rate of carbon steel in concrete in the presence of boric acid is lacking in published literature and available data are equivocal on the effect of boric acid on rebar corrosion, corrosion rate measurements were conducted in this study using several test methods. Rebar corrosion rates were measured in (i borated water flowing in a simulated concrete crack, (ii borated water flowing over a concrete surface, (iii borated water that has reacted with concrete, and (iv 2,400 ppm boric acid solutions with pH adjusted to a range of 6.0 to 7.7. The corrosion rates were measured using coupled multielectrode array sensor (CMAS and linear polarization resistance (LPR probes, both made using carbon steel. The results indicate that rebar corrosion rates are low (~1 μm/yr or lesswhen the solution pH is ~7.1 or higher. Below pH ~7.1, the corrosion rate increases with decreasing pH and can reach ~100 μm/yr in solutions with pH less than ~6.7. The threshold pH for carbon steel corrosion in borated solution is between 6.8 and 7.3.

BWR steel containment corrosion

Energy Technology Data Exchange (ETDEWEB)

Tan, C.P.; Bagchi, G.

1996-04-01

The report describes regulatory actions taken after corrosion was discovered in the drywell at the Oyster Creek Plant and in the torus at the Nine Mile Point 1 Plant. The report describes the causes of corrosion, requirements for monitoring corrosion, and measures to mitigate the corrosive environment for the two plants. The report describes the issuances of generic letters and information notices either to collect information to determine whether the problem is generic or to alert the licensees of similar plants about the existence of such a problem. Implementation of measures to enhance the containment performance under severe accident conditions is discussed. A study by Brookhaven National Laboratory (BNL) of the performance of a degraded containment under severe accident conditions is summarized. The details of the BNL study are in the appendix to the report.

Research on corrosion mechanism of suspension insulator steel foot of direct current system and measures for corrosion inhibition

Science.gov (United States)

Chen, He; Yang, Yueguang; Su, Guolei; Wang, Xiaoqing; Zhang, Hourong; Sun, Xiaoyu; Fan, Youping

2017-09-01

There are increasingly serious electrocorrosion phenomena on insulator hardware caused by direct current transmission due to the wide-range popularization of extra high voltage direct current transmission engineering in our country. Steel foot corrosion is the main corrosion for insulators on positive polarity side of transmission lines. On one hand, the corrosion leads to the tapering off of steel foot diameter, having a direct influence on mechanical property of insulators; on the other hand, in condition of corrosion on steel foot wrapped in porcelain ware, the volume of the corrosion product is at least 50% more than that of the original steel foot, leading to bursting of porcelain ware, threatening safe operation of transmission lines. Therefore, it is necessary to conduct research on the phenomenon and propose feasible measures for corrosion inhibition. Starting with the corrosion mechanism, this article proposes two measures for corrosion inhibition, and verifies the inhibition effect in laboratory conditions, providing reference for application in engineering.

Corrosion Monitoring System

Energy Technology Data Exchange (ETDEWEB)

Dr. Russ Braunling

2004-10-31

The Corrosion Monitoring System (CMS) program developed and demonstrated a continuously on-line system that provides real-time corrosion information. The program focused on detecting pitting corrosion in its early stages. A new invention called the Intelligent Ultrasonic Probe (IUP) was patented on the program. The IUP uses ultrasonic guided waves to detect small defects and a Synthetic Aperture Focusing Technique (SAFT) algorithm to provide an image of the pits. Testing of the CMS demonstrated the capability to detect pits with dimensionality in the sub-millimeter range. The CMS was tested in both the laboratory and in a pulp and paper industrial plant. The system is capable of monitoring the plant from a remote location using the internet.

Effect of zinc injection on BWR fuel cladding corrosion. Pt. 1. Study on an accelerated corrosion condition to evaluate corrosion resistance of zircaloy-2 fuel cladding

International Nuclear Information System (INIS)

Kawamura, Hirotaka; Kanbe, Hiromu; Furuya, Masahiro

2002-01-01

Japanese BWR utilities have a plan to apply zinc injection to the primary coolant in order to reduce radioactivity accumulation on the structure. Prior to applying the zinc injection to BWR plants, it is necessary to evaluate the effect of zinc injection on corrosion resistance of fuel cladding. The objective of this report was to examine the accelerated corrosion condition for evaluation of BWR fuel cladding corrosion resistance under non-irradiated conditions, as the first step of a zinc injection evaluation study. A heat transfer corrosion test facility, in which a two phase flow condition could be achieved, was designed and constructed. The effects of heat flux, void fraction and solution temperature on BWR fuel cladding corrosion resistance were quantitatively investigated. The main findings were as follows. (1) In situ measurements using high speed camera and a void sensor together with one dimensional two phase flow analysis results showed that a two phase flow simulated BWR core condition can be obtained in the corrosion test facility. (2) The heat transfer corrosion test results showed that the thickness of the zirconium oxide layer increased with increasing solution temperature and was independent of heat flux and void fraction. The corrosion accelerating factor was about 2.5 times in the case of a temperature increase from 288degC to 350degC. (author)

Current status of studies on nodular corrosion

International Nuclear Information System (INIS)

Yasuda, Takayoshi; Kawasaki, Satoru; Echigoya, Hironori; Kinoshita, Yutaka; Kubota, Hiroyuki; Konishi, Takao; Yamanaka, Tuneyasu.

1993-01-01

The studies on nodular corrosion formed on the outer surface of BWR fuel cladding tubes were reviewed. Main factors affecting the corrosion behavior were material and environmental conditions and combined effect. The effects of such material conditions as fabrication process, alloy elements, texture and surface treatment and environmental factors as neutron irradiation, thermo-hydrodynamic, water chemistry, purity of the coolant and contact with foreign metals on the corrosion phenomena were surveyed. Out-of-reactor corrosion test methods and models for the corrosion mechanism were also reviewed. Suppression of the accumulated annealing temperature during tube reduction process improved the nodular corrosion resistance of Zircaloys. Improved resistance for the nodular corrosion was reported for the unirradiated Zircaloys with some additives. Detailed irradiation test under the BWR conditions is needed to confirm the trend. Concerning the environmental factors, boiling on the cladding surface due to heat flux reduces the nodular corrosion susceptibility, while oxidizing radical generated from dissolved oxygen accelerates the corrosion. Concerning corrosion mechanisms, importance of such phenomena as the depleted zone of alloying elements in zirconium matrix, reduction of H + to H 2 in oxide layer, electrochemical property of precipitates, crystallographic anisotropy of oxidation rates were revealed. (author) 59 refs

Corrosion problems in light water nuclear reactors

International Nuclear Information System (INIS)

Berry, W.E.

1984-01-01

The corrosion problems encountered during the author's career are reviewed. Attention is given to the development of Zircaloys and attendant factors that affect corrosion; the caustic and chloride stress corrosion cracking (SCC) of austenitic stainless steel steam generator tubing; the qualification of Inconel Alloy 600 for steam generator tubing and the subsequent corrosion problem of secondary side wastage, caustic SCC, pitting, intergranular attack, denting, and primary side SCC; and SCC in weld and furnace sensitized stainless steel piping and internals in boiling water reactor primary coolants. Also mentioned are corrosion of metallic uranium alloy fuels; corrosion of aluminum and niobium candidate fuel element claddings; crevice corrosion and seizing of stainless steel journal-sleeve combinations; SCC of precipitation hardened and martensitic stainless steels; low temperature SCC of welded austenitic stainless steels by chloride, fluoride, and sulfur oxy-anions; and corrosion problems experienced by condensers

Corrosion chemistry closing comments: opportunities in corrosion science facilitated by operando experimental characterization combined with multi-scale computational modelling.

Science.gov (United States)

Scully, John R

2015-01-01

Recent advances in characterization tools, computational capabilities, and theories have created opportunities for advancement in understanding of solid-fluid interfaces at the nanoscale in corroding metallic systems. The Faraday Discussion on Corrosion Chemistry in 2015 highlighted some of the current needs, gaps and opportunities in corrosion science. Themes were organized into several hierarchical categories that provide an organizational framework for corrosion. Opportunities to develop fundamental physical and chemical data which will enable further progress in thermodynamic and kinetic modelling of corrosion were discussed. These will enable new and better understanding of unit processes that govern corrosion at the nanoscale. Additional topics discussed included scales, films and oxides, fluid-surface and molecular-surface interactions, selected topics in corrosion science and engineering as well as corrosion control. Corrosion science and engineering topics included complex alloy dissolution, local corrosion, and modelling of specific corrosion processes that are made up of collections of temporally and spatially varying unit processes such as oxidation, ion transport, and competitive adsorption. Corrosion control and mitigation topics covered some new insights on coatings and inhibitors. Further advances in operando or in situ experimental characterization strategies at the nanoscale combined with computational modelling will enhance progress in the field, especially if coupling across length and time scales can be achieved incorporating the various phenomena encountered in corrosion. Readers are encouraged to not only to use this ad hoc organizational scheme to guide their immersion into the current opportunities in corrosion chemistry, but also to find value in the information presented in their own ways.

A Theoretical Model for Metal Corrosion Degradation

Directory of Open Access Journals (Sweden)

David V. Svintradze

2010-01-01

Full Text Available Many aluminum and stainless steel alloys contain thin oxide layers on the metal surface which greatly reduce the corrosion rate. Pitting corrosion, a result of localized breakdown of such films, results in accelerated dissolution of the underlying metal through pits. Many researchers have studied pitting corrosion for several decades and the exact governing equation for corrosion pit degradation has not been obtained. In this study, the governing equation for corrosion degradation due to pitting corrosion behavior was derived from solid-state physics and some solutions and simulations are presented and discussed.

Corrosion of high temperature resisting alloys exposed to heavy fuel ash; Corrosion de aleaciones resistentes a altas temperaturas expuestas a ceniza de combustoleo pesado

Energy Technology Data Exchange (ETDEWEB)

Wong Moreno, Adriana del Carmen

1998-03-01

aleaciones de diferente tipo (aceros de baja y media aleacion, aceros inoxidables ferriticos y austeniticos, aleaciones base niquel y una aleacion FeCrAl del tipo ODS) expuestas a temperaturas elevadas (580 grados Celsius - 900 grados Celsius) a 15 depositos de ceniza con diferente potencial corrosivo, los cuales fueron colectados de la zona de alta temperatura de calderas de centrales termoelectricas. Los estudios posteriores a los ensayos de corrosion consistieron en el analisis por microscopia electronica de barrido apoyada con microanalisis de las probetas corroidas, con el fin de determinar el efecto de Na, V y S sobre la corrosividad de los depositos de ceniza y el efecto de los principales elementos aleantes sobre la resistencia a la corrosion de las aleaciones. Tales efectos son ampliamente documentados y discutidos para apoyar los mecanismos propuestos de degradacion que estan operando. El analisis global de los resultados generados ha permitido proponer un modelo para explicar el mecanismo global de corrosion de aleaciones expuestas a altas temperaturas de depositos de ceniza. El modelo propuesto, complementa el elaborado por Wilson, ampliamente aceptado para vanadatos fundidos, en cuanto a que por un lado, considera el efecto de la presencia de sulfato de sodio (ademas de los compuestos de vanadio) en los depositos, y por otro, lo extiende a temperaturas mas altas que el punto de fusion de los compuestos de vanadio constituyentes de los depositos. Ambos aspectos involucran el considerar el papel que el proceso de difusion de especies tiene sobre la degradacion y la capacidad de proteccion de la aleacion. La investigacion realizada permitio confirmar lo establecido por el modelo de Wilson para depositos con alto contenido de vanadio y muy bajo contenido de azufre, a las temperaturas proximas al punto de fusion de los compuestos de vanadio que los constituyen. El desarrollo de los procesos de deterioro metalico que se incluyen en el modelo propuesto fue documentado

A Multifunctional Smart Coating for Autonomous Corrosion Control

Science.gov (United States)

Calle, Luz Marina; Buhrow, Jerry W.; Jolley, Scott T.

2012-01-01

Corrosion is a destructive process that often causes failure in metallic components and structures. Protective coatings are the most commonly used method of corrosion control. However, progressively stricter environmental regulations have resulted in the ban of many commercially available corrosion protective coatings due to the harmful effects of their solvents or corrosion inhibitors. This work concerns the development of a multifunctional, smart coating for the autonomous control of corrosion. This coating is being developed to have the inherent ability to detect the chemical changes associated with the onset of corrosion and respond autonomously to control it. The multi-functionality of the coating is based on micro-encapsulation technology specifically designed for corrosion control applications. This design has, in addition to all the advantages of other existing microcapsules designs, the corrosion controlled release function that allows the delivery of corrosion indicators and inhibitors on demand only when and where needed. Corrosion indicators as well as corrosion inhibitors have been incorporated into microcapsules, blended into several paint systems, and tested for corrosion detection and protection efficacy. This

Corrosion in power industry

International Nuclear Information System (INIS)

Ventakeshwarlu, K.S.

1979-01-01

A brief account of the problem areas encountered as a result of corrosion in the electrical power industry including nuclear power industry is given and some of the measures contemplated and/or implemented to control corrosion are outlined. The corrosion problems in the steam generators and cladding tubes of the nuclear power plant have an added dimension of radioactivation which leads to contamination and radiation field. Importance of monitoring water quality and controlling water chemistry by addition of chemicals is emphasised. (M.G.B.)

Corrosion investigations of high-alloyed steels carried out in different marine area organized by European Federation of Corrosion

International Nuclear Information System (INIS)

Birn, J.; Skalski, I.

1999-01-01

Research works arranged by EFC Working Party on Marine Corrosion are described. The research was performed in sea areas of Norway, Finland, Sweden, France, Italy, Poland and Netherlands. Subjected to test were three corrosion resistant steel grades; 316, 904 and UNS S 31524. Two corrosion tests were carried out in the years 1993 and 1994 each of min. 6 month duration. The results show that chemical composition of water at salinity level of more than 0.7% has not great effect on corrosion aggressivity in relation to corrosion resistant steels. On the other hand temperature of sea water has great influence on corrosion process. (author)

Corrosion and alteration of materials from the nuclear industry

International Nuclear Information System (INIS)

Beauvy, M.; Berthoud, G.; Defranceschi, M.; Ducros, G.; Feron, D.; Guerin, Y.; Latge, C.; Limoge, Y.; Madic, C.; Santarini, G.; Seiler, J.M.; Vernaz, E.; Richet, C.

2010-01-01

The control of the corrosion phenomenon is of prime importance for the nuclear industry. The efficiency and the safety of facilities can be affected by this phenomenon. The nuclear industry has to face corrosion for a large variety of materials submitted to various environments. Metallic corrosion operates in the hot and aqueous environment of water reactors which represent the most common reactor type in the world. Progresses made in the control of the corrosion of the different components of these reactors allow to improve their safety. Corrosion is present in the facilities of the back-end of the fuel cycle as well (corrosion in acid environment in fuel reprocessing plants, corrosion of waste containers in disposal and storage facilities, etc). The future nuclear systems will widen even more the range of materials to be studied and the situations in which they will be placed (corrosion by liquid metals or by helium impurities). Very often, corrosion looks like a patchwork of particular cases in its description. The encountered corrosion problems and their study are presented in this book according to chapters representing the main sectors of the nuclear industry and classified with respect to their phenomenology. This monograph illustrates the researches in progress and presents some results of particular importance obtained recently. Content: 1 - Introduction: context, stakes and goals; definition of corrosion; a complex science; corrosion in the nuclear industry; 2 - corrosion in water reactors - phenomenology, mechanisms, remedies: A - uniform corrosion: mechanisms, uniform corrosion of fuel cladding, in-situ measurement of generalized corrosion rate by electrochemical methods, uniform corrosion of nickel alloys, characterization of the passive layer and growth mechanisms, the PACTOLE code - an integrating tool, influence of water chemistry on corrosion and contamination, radiolysis impact on uniform corrosion; B - stress corrosion: stress corrosion cracking

Development of Flow Accelerated Corrosion Reduction Technology

Energy Technology Data Exchange (ETDEWEB)

Heo, Min Bum; Choi, Won Yeol; Lee, Jong Chan; Lim, Dong Seok; Kwon, Byung Il; Ku, Hee Kwon; Kim, Jong Uk [FNC Tech, Yongin (Korea, Republic of)

2015-10-15

Development of flow accelerated corrosion reduction technology is necessary for prevent this kind of accidents. This study deals with development of flow accelerated corrosion reduction technology through platinum injection and developed of flow accelerated corrosion reduction technology by imitating water chemical condition in PWR secondary system in practice. In addition, in order to get reliability of water chemical simulator in PWR secondary system, analyzed and compared with test result through CFD analysis. This study composed test device that can simulate water chemical environment in PWR secondary system, in order to develop flow accelerated corrosion reduction , and evaluated the ratio of corrosion in water chemical environment in PWR secondary system. In conclusion, corrosion ratio of low alloy steel material that includes more Cr and Mo was lower. And the results were confirmed to be the maximum corrosion rate in the case that replicate the 90 elbow. Additionally, inserted Pt nano particle for developing flow accelerated corrosion rate reduction technology, the test results, it was confirmed for about 80% of the flow accelerated corrosion rate reduction than before input.

The Effects of Corrosive Chemicals on Corrosion Rate of Steel Reinforcement Bars: I. Swamp Water

Directory of Open Access Journals (Sweden)

Sulistyoweni Widanarko

2010-10-01

Full Text Available Most of infrastructures using steel concrete to reinforce the strength of concrete. Steel concrete is so vulnerable to chemical compounds that can cause corrosion. It can happen due to the presence of chemical compounds in acid environment in low pH level. These chemical compounds are SO42-, Cl-, NO3-. There are many swamp area in Indonesia. The acid contents and the concentration of ion sulphate, chlorides, and nitrate are higher in the swamp water than in the ground water .The objective of this research was to find out the influence of corrosive chemicals in the swamp water to the steel concrete corrosion rate. There were two treatment used: (1 emerging ST 37 and ST 60 within 60 days in the 'polluted' swamp water, (2 moving the ST 37 up and down periodically in the ' polluted' swamp water. Three variation of 'polluted' swamp water were made by increasing the concentration of corrosive chemical up to 1X, 5X and 10X respectively. The corrosion rate was measured by using an Immersion Method. The result of Immersion test showed that chloride had the greatest influence to corrosion rate of ST 37 and ST 60 and followed by sulphate and Nitrate. Corrosion rate value for ST 37 is 24.29 mpy and for ST 60 is 22.76 mpy. By moving the sample up and down, the corrosion rate of ST 37 increase up to 37.59 mpy, and chloride still having the greatest influence, followed by sulphate and nitrate.

Critical Study of Corrosion Damaged Concrete Structures

OpenAIRE

Sallehuddin Shah Ayop; John Cairns

2013-01-01

Corrosion of steel reinforcement in concrete is one of the major problems with respect to the durability of reinforced concrete structures. The degradation of the structure strength due to reinforcement corrosion decreases its design life. This paper presents the literature study on the influence of the corrosion on concrete structure starting from the mechanism of the corrosion until the deterioration stage and the structural effects of corrosion on concrete structures.

Graphene: corrosion-inhibiting coating.

Science.gov (United States)

Prasai, Dhiraj; Tuberquia, Juan Carlos; Harl, Robert R; Jennings, G Kane; Rogers, Bridget R; Bolotin, Kirill I

2012-02-28

We report the use of atomically thin layers of graphene as a protective coating that inhibits corrosion of underlying metals. Here, we employ electrochemical methods to study the corrosion inhibition of copper and nickel by either growing graphene on these metals, or by mechanically transferring multilayer graphene onto them. Cyclic voltammetry measurements reveal that the graphene coating effectively suppresses metal oxidation and oxygen reduction. Electrochemical impedance spectroscopy measurements suggest that while graphene itself is not damaged, the metal under it is corroded at cracks in the graphene film. Finally, we use Tafel analysis to quantify the corrosion rates of samples with and without graphene coatings. These results indicate that copper films coated with graphene grown via chemical vapor deposition are corroded 7 times slower in an aerated Na(2)SO(4) solution as compared to the corrosion rate of bare copper. Tafel analysis reveals that nickel with a multilayer graphene film grown on it corrodes 20 times slower while nickel surfaces coated with four layers of mechanically transferred graphene corrode 4 times slower than bare nickel. These findings establish graphene as the thinnest known corrosion-protecting coating.

Colorimetric visualization of tin corrosion: A method for early stage corrosion detection on printed circuit boards

DEFF Research Database (Denmark)

Verdingovas, Vadimas; Jellesen, Morten Stendahl; Ambat, Rajan

2017-01-01

A majority of printed circuit board surfaces are covered with tin, therefore tin corrosion under humid conditions and movement of tin ions under the influence of an electric field plays an important role in the corrosion failure development. Tracking tin corrosion products spread on the printed c...

Corrosion in the nuclear power industry

International Nuclear Information System (INIS)

Danko, J.C.

1987-01-01

This article reviews the major corrosion problems in light water reactors, the research on the corrosion mechanism(s), and the development of engineering solutions and their implementation. To understand the occurrence of corrosion problems, a brief historical perspective of the corrosion design basis of commercial light water reactors, boiling water, and pressurized water reactors is necessary. Although corrosion was considered in the plant designs, it was not viewed as a serious problem. This was based on the results of laboratory experiments and in-reactor tests that did not indicate any major corrosion problems with the materials selected for the plant construction. However, the laboratory tests did not necessarily reproduce the reactor operating conditions and the early in-reactor test did not fully represent the commercial reactor conditions in all cases, and, finally, the test times were indeed of short duration relative to the plant design lifetime of 40 years. Thus, the design basis for the materials selection was determined on the favorable but limited test data that were available, and corrosion limitations on component integrity were therefore not anticipated

Marine atmospheric corrosion of carbon steels

Energy Technology Data Exchange (ETDEWEB)

Morcillo, M.; Alcantara, J.; Diaz, I.; Chico, B.; Simancas, J.; Fuente, D. de la

2015-07-01

Basic research on marine atmospheric corrosion of carbon steels is a relatively young scientific field and there continue to be great gaps in this area of knowledge. The presence of akaganeite in the corrosion products that form on steel when it is exposed to marine atmospheres leads to a notable increase in the corrosion rate. This work addresses the following issues: (a) environmental conditions necessary for akaganeite formation; (b) characterisation of akaganeite in the corrosion products formed; (c) corrosion mechanisms of carbon steel in marine atmospheres; (d) exfoliation of rust layers formed in highly aggressive marine atmospheres; (e) long-term corrosion rate prediction; and (f) behaviour of weathering steels. Field research has been carried out at Cabo Vilano wind farm (Camarinas, Galicia) in a wide range of atmospheric salinities and laboratory work involving the use of conventional atmospheric corrosion techniques and near-surface and bulk sensitive analytical techniques: scanning electron microscopy (SEM)/energy dispersive spectrometry (EDS), X-ray diffraction (XRD), Mossbauer spectroscopy and SEM/μRaman spectroscopy. (Author)

Study on influence of native oxide and corrosion products on atmospheric corrosion of pure Al

International Nuclear Information System (INIS)

Liu, Yanjie; Wang, Zhenyao; Ke, Wei

2014-01-01

Highlights: •Corrosion products layer is only formed in coastal atmosphere. •In coastal atmosphere, rate controlling step is diffusion process. •In rural atmosphere, rate controlling step is charge transfer process. •Pitting area increases greatly in coastal site, but slightly in rural site. -- Abstract: Effects of native oxide and corrosion products on atmospheric corrosion of aluminium in rural and coastal sites were studied by electrochemical impedance spectroscopy (EIS), open-circuit potential (OCP) and scanning electron microscope (SEM) techniques after outdoor exposure. In the rural atmosphere, only the compact, adhesive native oxide layer exists, and the rate controlling step is diffusion process, while in the coastal atmosphere, another loose, inadhesive corrosion products layer exists, and a charge transfer process controls the corrosion process. The pitting area in the coastal atmosphere increases over time more obviously than that in the rural atmosphere

Corrosive wear. Evaluation of wear and corrosive resistant materials; Noetningskorrosion. Utvaerdering av noetnings- och korrosionsbestaendiga material

Energy Technology Data Exchange (ETDEWEB)

Persson, H.; Hjertsen, D.; Waara, P.; Prakash, B.; Hardell, J.

2007-12-15

With a new purchase of a waste conveyer screw at hand, for the 'A-warehouse' at the combined power and heating plant at E.ON Norrkoeping, the request for improved construction materials was raised. The previous screw required maintenance with very short intervals due to the difficult operation conditions. With the new screw the expectation is to manage 6 months of operation without interruption. The environment for the screw has two main components that sets the demand on the materials, on one hand the corrosive products that comes along and which forms at digestion of the waste and on the other hand the abrasive content in the waste. The term of the mechanism is wear-corrosion and can give considerably higher material loss than the two mechanisms wear and corrosion separately. Combination of a strong corrosive environment together with extensive wear is something that we today have limited knowledge about. The overall objective of the project has been to establish better wear and corrosive resistant construction materials for a waste conveyer screw that will lead to reduced operational disturbance costs. The evaluation has been performed in both controlled laboratory environments and in field tests, which has given us a better understanding of what materials are more suitable in this tough environment and has given us a tool for future predictions of the wear rate of the different material. The new conveyer screw, installed in February 2007 and with which the field test have been performed, has considerably reduced the wear of the construction and the target of 6 month maintenance-free operation is met with this screw for all the evaluated materials. The wear along the screw varies very much and with a clear trend for all the materials to increase towards the feeding direction of the screw. As an example, the wear plate SS2377 (stainless duplex steel) has a useful life at the most affected areas that is calculated to be 1077 days of operation with the

Corrosion-resistant coating development

Energy Technology Data Exchange (ETDEWEB)

Stinton, D.P.; Kupp, D.M.; Martin, R.L. [Oak Ridge National Lab., TN (United States)

1997-12-01

SiC-based heat exchangers have been identified as the prime candidate material for use as heat exchangers in advanced combined cycle power plants. Unfortunately, hot corrosion of the SiC-based materials created by alkali metal salts present in the combustion gases dictates the need for corrosion-resistant coatings. The well-documented corrosion resistance of CS-50 combined with its low (and tailorable) coefficient of thermal expansion and low modulus makes CS-50 an ideal candidate for this application. Coatings produced by gelcasting and traditional particulate processing have been evaluated.

Proyecto de factibilidad para la creación de una Unidad Educativa Particular en la parroquia El Corazón, cantón Pangua, provincia de Cotopaxi.

OpenAIRE

Merino Illauri, Carmen Enith

2012-01-01

La educación en el Ecuador en los últimos años se ha visto afectada por índices preocupantes de: analfabetismo, bajo nivel de escolaridad, tasas de repetición, deserción escolar, mala calidad de la educación, deficiente infraestructura educativa y material didáctico obsoleto. Todos los esfuerzos que se realicen para eliminar estas situaciones serán provechos para el desarrollo del país. Es realmente importante unidades educativas que mitiguen en parte estas falencias anteriormente menciona...

Ductilidad y tenacidad de un borde cortado por plasma en una chapa de acero S460M de 15 mm de espesor

OpenAIRE

Aldazabal, J.; Martín-Meizoso, A.; Cicero González, Sergio; Klimpel, A.; Bannister, A.

2015-01-01

Los procesos de corte (y soldadura) son sin duda traumáticos para la microestructura de los materiales, de los que se deriva su comportamiento mecánico. Además esto afecta a la superficie, lo que agrava el problema, pues con frecuencia son las zonas que soportan unos mayores esfuerzos. En este trabajo se propone determinar si un corte por plasma mejora o no su comportamiento mecánico (fundamentalmente de cara a su comportamiento en fatiga bajo cargas alternadas). Se presentan los resultado...

Política y Administración Provincial. La Diputación de Sevilla durante la Dictadura de Primo de Rivera y la II República (1923-1936).

OpenAIRE

Ponce Alberca, Julio

2016-01-01

Desde la perspectiva de fines del siglo XX, los regímenes políticos de la España de los años veinte y treinta aparecen como una secuencia de ensayos en respuesta a la profunda crisis sufrida por el sistema de la Restauración (1876-1923). Bajo ese enfoque, la Segunda República (1931-1936) se nos muestra inscrita en el esfuerzo por encontrar una nueva alternativa tras el fracaso de la Dictadura primorriverista (1923-1930) y las dictablandas del genera...

Restos de vida en Bajo este sol tremendo de Carlos Busqued

Directory of Open Access Journals (Sweden)

Marcos Seifert

2017-07-01

Full Text Available Este trabajo se propone analizar cómo la novela de Carlos Busqued Bajo este sol tremendo (2009 se apoya en la representación de vidas desechadas, basura y todo tipo de restos para instalarse en una tensión entre orden y exceso. La narración plantea una lógica en la que la basura, en lugar de constituirse en un indicio que posibilite la reconstrucción del paisaje social, exhibe lo desbordante, lo inasimilable y los vacíos de sentido. En el mundo que nos presenta Busqued lo viviente se vuelve resto en la medida en que encarna una heterogeneidad irreductible a cualquier estructura social y productiva. This paper analyzes the way in which Carlos Busqued's novel Bajo este sol tremendo (2009 is based on the representation of discarded lives, garbage, and all kinds of remains and thus proposes a tension between order and excess. The narration raises a logic in which garbage, instead of constituting an indicator that allows for the reconstruction of the social landscape, exhibits the overflowing, the unassimilable, and the voids of meaning. In the world that Busqued presents, the living becomes a remainder because it embodies an irreducible heterogeneity with regards to any social and productive structure.

Virtual Instrumentation Corrosion Controller for Natural Gas Pipelines

Science.gov (United States)

Gopalakrishnan, J.; Agnihotri, G.; Deshpande, D. M.

2012-12-01

Corrosion is an electrochemical process. Corrosion in natural gas (methane) pipelines leads to leakages. Corrosion occurs when anode and cathode are connected through electrolyte. Rate of corrosion in metallic pipeline can be controlled by impressing current to it and thereby making it to act as cathode of corrosion cell. Technologically advanced and energy efficient corrosion controller is required to protect natural gas pipelines. Proposed virtual instrumentation (VI) based corrosion controller precisely controls the external corrosion in underground metallic pipelines, enhances its life and ensures safety. Designing and development of proportional-integral-differential (PID) corrosion controller using VI (LabVIEW) is carried out. When the designed controller is deployed at field, it maintains the pipe to soil potential (PSP) within safe operating limit and not entering into over/under protection zone. Horizontal deployment of this technique can be done to protect all metallic structure, oil pipelines, which need corrosion protection.

49 CFR 193.2631 - Internal corrosion control.

Science.gov (United States)

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Internal corrosion control. 193.2631 Section 193... GAS FACILITIES: FEDERAL SAFETY STANDARDS Maintenance § 193.2631 Internal corrosion control. Each component that is subject to internal corrosive attack must be protected from internal corrosion by— (a...

Fatigue and Corrosion in Metals

CERN Document Server

Milella, Pietro Paolo

2013-01-01

This textbook, suitable for students, researchers and engineers, gathers the experience of more than 20 years of teaching fracture mechanics, fatigue and corrosion to professional engineers and running experimental tests and verifications to solve practical problems in engineering applications. As such, it is a comprehensive blend of fundamental knowledge and technical tools to address the issues of fatigue and corrosion. The book initiates with a systematic description of fatigue from a phenomenological point of view, since the early signs of submicroscopic damage in few surface grains and continues describing, step by step, how these precursors develop to become mechanically small cracks and, eventually, macrocracks whose growth is governed by fracture mechanics. But fracture mechanics is also introduced to analyze stress corrosion and corrosion assisted fatigue in a rather advanced fashion. The author dedicates a particular attention to corrosion starting with an electrochemical treatment that mechanical e...

Benchmarking of Zinc Coatings for Corrosion Protection: A Detailed Characterization of Corrosion and Electrochemical Properties of Zinc Coatings

Energy Technology Data Exchange (ETDEWEB)

Wijesinghe, Sudesh L; Zixi, Tan [Singapore Institute of Manufacturing Technology, Nanyang Drive (Singapore)

2017-02-15

Due to various types of Zn coatings for many decades for various applications, it is imperative to study and compare their corrosion resistance properties of some of these. Here, we introduce a systematic methodology for evaluation and validation of corrosion protection properties of metallic coatings. According to this methodology, samples are were exposed in an advanced cyclic corrosion test chamber according to ISO 14993, and removed at the end of each withdrawal for respective corrosion and electrochemical characterization to evaluate both barrier and galvanic protection properties. Corrosion protection properties of coatings were evaluated by visual examination according to ISO 10289, mass loss and subsequent corrosion rate measurements, electrochemical properties, and advanced electrochemical scanning techniques. In this study, corrosion protection properties of a commercial zinc rich coating (ZRC) on AISI 1020 mild steel substrates were evaluated and benchmarked against hot dip galvanized (HDG). Results were correlated, and corrosion protection capabilities of the two coatings were compared. The zinc rich coating performed better than hot dip galvanized coating in terms of overall corrosion protection properties, according to the exposure and experimental conditions used in this study. It proved to be a suitable candidate to replace hot dip galvanized coatings for desired applications.

Corrosion Rate Monitoring in District Heating Systems

DEFF Research Database (Denmark)

Hilbert, Lisbeth Rischel; Nielsen, Lars Vendelbo; Andersen, A.

2005-01-01

be applicable, and if on-line monitoring could improve the quality control. Water quality monitoring was applied as well as corrosion rate monitoring with linear polarization resistance (LPR), electrochemical impedance spectroscopy (EIS), electrical resistance (ER) technique, mass loss and a crevice corrosion......Quality control in district heating systems to keep uniform corrosion rates low and localized corrosion minimal is based on water quality control. Side-stream units equipped with carbon steel probes for online monitoring were mounted in district heating plants to investigate which techniques would...... cell for localized corrosion risk estimation. Important variations in corrosion rate due to changes in make-up water quality were detected with the continuous monitoring provided by ER and crevice cell, while LPR gave unreliable corrosion rates. The acquisition time of two-three days for EIS...

49 CFR 192.477 - Internal corrosion control: Monitoring.

Science.gov (United States)

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Internal corrosion control: Monitoring. 192.477... Control § 192.477 Internal corrosion control: Monitoring. If corrosive gas is being transported, coupons... internal corrosion. Each coupon or other means of monitoring internal corrosion must be checked two times...

Corrosion testing and prediction in SCWO environments

International Nuclear Information System (INIS)

Kriksunov, L.B.; Macdonald, D.D.

1995-01-01

The authors review recent advances in corrosion monitoring and modeling in SCWO systems. Techniques and results of experimental corrosion measurements at high temperatures are presented. Results of modeling corrosion in high subcritical and supercritical aqueous systems indicate the primary importance of density of water in corrosion processes. A phenomenological model has been developed to simulate corrosion processes at nearcritical and supercritical temperatures in SCWO systems. They discuss as well the construction of Pourbaix diagrams for metals in SCW

Corrosion monitoring during a chemical cleaning

International Nuclear Information System (INIS)

Delepine, J.; Feron, D.; Roy, M.

1994-01-01

In order to estimate the possible corrosion induced by the chemical cleaning, a corrosion monitoring has been realized during the cleaning of the secondary circuit (including the model boiler) of ORION loop. It included coupons and electrodes and has required a preliminary setting in laboratory. The electrochemical device which was used during the chemical cleaning included two reference electrodes (Ag/AgCl) and eight metallic electrodes (carbon steel, stainless steel, Alloy 600 and Alloy 690) for free corrosion potential monitoring, three other carbon steel electrodes for instantaneous corrosion rate measurements by polarization resistance and three coupling devices with different surface ratios between carbon steel and Alloy 600. The results showed a good agreement between corrosion rates measured by weight losses on coupons or by electrochemistry (polarization resistance), and an increase of the carbon steel corrosion rate when it was coupled with Alloy 600. (authors). 5 figs., 2 tabs., 3 refs

Localized Corrosion Behavior of Type 304SS with a Silica Layer Under Atmospheric Corrosion Environments

International Nuclear Information System (INIS)

E. Tada; G.S. Frankel

2006-01-01

The U.S. Department of Energy (DOE) has proposed a potential repository for spent nuclear fuel and high-level radioactive waste at the Yucca Mountain site in Nevada. [I] The temperature could be high on the waste packages, and it is possible that dripping water or humidity could interact with rock dust particulate to form a thin electrolyte layer with concentrated ionic species. Under these conditions, it is possible that highly corrosion-resistant alloys (CRAs) used as packages to dispose the nuclear waste could suffer localized corrosion. Therefore, to better understand long-term corrosion performance of CRAs in the repository, it is important to investigate localized corrosion under a simulated repository environment. We measured open circuit potential (OCP) and galvanic current (i g ) for silica-coated Type 304SS during drying of salt solutions under controlled RH environments to clarify the effect of silica layer as a dust layer simulant on localized corrosion under atmospheric environments. Type 304SS was used as a relatively susceptible model CRA instead of the much more corrosion resistant alloys, such as Alloy 22, that are being considered as, waste package materials

Demystifying Controlling Copper Corrosion

Science.gov (United States)

The LCR systematically misses the highest health and corrosion risk sites for copper. Additionally, there are growing concerns for WWTP copper in sludges and discharge levels. There are many corrosion control differences between copper and lead. This talk explains the sometimes c...

Corrosion protection with eco-friendly inhibitors

Science.gov (United States)

Shahid, Muhammad

2011-12-01

Corrosion occurs as a result of the interaction of a metal with its environment. The extent of corrosion depends on the type of metal, the existing conditions in the environment and the type of aggressive ions present in the medium. For example, CO3-2 and NO-3 produce an insoluble deposit on the surface of iron, resulting in the isolation of metal and consequent decrease of corrosion. On the other hand, halide ions are adsorbed selectively on the metal surface and prevent formation of the oxide phase on the metal surface, resulting in continuous corrosion. Iron, aluminum and their alloys are widely used, both domestically and industrially. Linear alkylbenzene and linear alkylbenzene sulfonate are commonly used as detergents. They have also been found together in waste water. It is claimed that these chemicals act as inhibitors for stainless steel and aluminum. Release of toxic gases as a result of corrosion in pipelines may lead in certain cases to air pollution and possible health hazards. Therefore, there are two ways to look at the relationship between corrosion and pollution: (i) corrosion of metals and alloys due to environmental pollution and (ii) environmental pollution as a result of corrosion protection. This paper encompasses the two scenarios and possible remedies for various cases, using 'green' inhibitors obtained either from plant extracts or from pharmaceutical compounds. In the present study, the effect of piperacillin sodium as a corrosion inhibitor for mild steel was investigated using a weight-loss method as well as a three-electrode dc electrochemical technique. It was found that the corrosion rate decreased as the concentration of the inhibitor increased up to 9×10-4 M 93% efficiency was exhibited at this concentration.

Prediction of corrosion rates of water distribution pipelines according to aggressive corrosive water in Korea.

Science.gov (United States)

Chung, W S; Yu, M J; Lee, H D

2004-01-01

The drinking water network serving Korea has been used for almost 100 years. Therefore, pipelines have suffered various degrees of deterioration due to aggressive environments. The pipe breaks were caused by in-external corrosion, water hammer, surface loading, etc. In this paper, we focused on describing corrosion status in water distribution pipes in Korea and reviewing some methods to predict corrosion rates. Results indicate that corrosive water of lakes was more aggressive than river water and the winter was more aggressive compared to other seasons. The roughness growth rates of Dongbok lake showed 0.23 mm/year. The high variation of corrosion rates is controlled by the aging pipes and smaller diameter. Also the phenolphthalein test on a cementitious core of cement mortar lined ductile cast iron pipe indicated the pipes over 15 years old had lost 50-100% of their lime active cross sectional area.

Evaluación de la escala Borg de esfuerzo percibido aplicada a la rehabilitación cardiaca Instrument evaluation of Borg's perceived exertion scale in cardiac rehabilitation

Directory of Open Access Journals (Sweden)

Natalie Burkhalter

1996-12-01

Full Text Available La escala Borg de esfuerzo percibido mide la gama entera del esfuerzo que el individuo percibe al hacer ejercicio. Esta escala da criterios para hacerle ajustes a la intensidad de ejercicio, o sea, a la carga de trabajo, y así pronosticar y dictaminar las diferentes intensidades del ejercicio en los deportes y en la rehabilitación médica (BORG, 1982. También se puede usar tanto en el atletismo, en la astronáutica, la industria y ambientes militares, como en las situaciones cotidianas. El concepto del esfuerzo percibido es una valoración subjetiva que indica la opinión del sujeto respecto a la intensidad del trabajo realizado (MORGAN, 1973. El sujeto que hace el ejercicio debe asignar un número del 1 al 20, para representar la sensación subjetiva de la cantidad de trabajo desempeñado. La escala es una herramienta valiosa dentro del ámbito del desempeño humano, en que a menudo la consideración importante no es tanto "lo que haga el individuo" "sino" "lo que cree que hace" (MORGAN, 1973.Borg's perceived exertion scale measures the extent of perceived exertion which a person experiences during exercise. The perceived exertion scale is used to adjust exercise intensity (workload for predictions and prescriptions of exercise intensities in sports and medical rehabilitation (BORG, 1982. In addition, Borg's scale can be used in the athletic arena, space, industry, military settings, or under everyday circumstances. The concept of perceived exertion is a subjective rating, indicating the subject's opinion about the intensity of the work being performed (MORGAN, 1973. The task of exercising subjects is to assign a number (from 1-20 to represent the subjective sensation of the amount of work being performed. This is a valuable tool in human performance setting, where an important consideration is not "what the individual is doing, but what he thinks and is doing" (MORGAN, 1973.

Corrosion of carbon steel under waste disposal conditions

International Nuclear Information System (INIS)

Marsh, G.

1990-01-01

The corrosion of carbon steel has been studied in the United Kingdom under granitic groundwater conditions, with pH between 5 and 10 and possibly substantial amounts of Cl - , SO 4 2- and HCO 3 - /CO 3 2- . Corrosion modes considered include uniform corrosion under both aerobic and anaerobic conditions; passive corrosion; localized attack in the form of pitting or crevice corrosion; and environmentally assisted cracking - hydrogen embrittlement or stress corrosion cracking. Studies of these processes are being carried out in order to predict the metal thicknesses required to give container lifetimes of 500 to 1000 years. A simple uniform corrosion model predicts a corrosion rate of around 13.4 μm/a at 20C, rising to 69 μm/a at 50C and 208 μm/a at 90C. A radiation dose of 10 5 rad/h and a G-value of 2.8 for the production of oxidizing species would account for an increase in corrosion rate of 7 μm/a. This model overestimates slightly the results actually achieved for experimental samples exposed for two years, the difference being due to a protective film formed on the samples. These corrosion rates predict that the container must be 227 mm thick to withstand uniform corrosion; however, they predict very high levels of hydrogen production. Conditions will be favourable for localized or pitting corrosion for about 125 years, leading to a maximum penetration of 160 mm. Since the exposure environment cannot be predicted precisely, one cannot state that stress corrosion cracking is impossible. Thus the container must be stress relieved. Other corrosion mechanisms such as microbial corrosion and hydrogen embrittlement are not considered significant

The corrosion behavior of DWPF glasses

International Nuclear Information System (INIS)

Ebert, W.L.; Bates, J.K.

1995-01-01

The authors analyzed the corroded surfaces of reference glasses developed for the Defense Waste Processing Facility (DWPF) to characterize their corrosion behavior. The corrosion mechanism of nuclear waste glasses must be known in order to provide source terms describing radionuclide release for performance assessment calculations. Different DWPF reference glasses were corroded under conditions that highlighted various aspects of the corrosion process and led to different extents of corrosion. The glasses corroded by similar mechanisms, and a phenomenological description of their corrosion behavior is presented here. The initial leaching of soluble glass components results in the formation of an amorphous gel layer on the glass surface. The gel layer is a transient phase that transforms into a layer of clay crystallites, which equilibrates with the solution as corrosion continues. The clay layer does not act as a barrier to either water penetration or glass dissolution, which continues beneath it, and may eventually separate from the glass. Solubility limits for glass components may be established by the eventual precipitation of secondary phases; thus, corrosion of the glass becomes controlled by the chemical equilibrium between the solution and the assemblage of secondary phases. In effect, the solution is an intermediate phase through which the glass transforms to an energetically more favorable assemblage of phases. Implications regarding the prediction of long-term glass corrosion behavior are discussed

Hanford transuranic storage corrosion review

International Nuclear Information System (INIS)

Nelson, J.L.; Divine, J.R.

1980-12-01

The rate of atmospheric corrosion of the transuranic (TRU) waste drums at the US Department of Energy's Hanford Project, near Richland, Washington, was evaluated by Pacific Northwest Laboratory (PNL). The rate of corrosion is principally contingent upon the effects of humidity, airborne pollutants, and temperature. Results of the study indicate that actual penetration of barrels due to atmospheric corrosion will probably not occur within the 20-year specified recovery period. Several other US burial sites were surveyed, and it appears that there is sufficient uncertainty in the available data to prevent a clearcut statement of the corrosion rate at a specific site. Laboratory and site tests are recommended before any definite conclusions can be made. The corrosion potential at the Hanford TRU waste site could be reduced by a combination of changes in drum materials (for example, using galvanized barrels instead of the currently used mild steel barrels), environmental exposure conditions (for example, covering the barrels in one of numerous possible ways), and storage conditions

Corrosion of Zircaloy-clad fuel rods in high-temperature PWRs: Measurement of waterside corrosion in North Anna Unit 1

International Nuclear Information System (INIS)

Balfour, M.G.; Kilp, G.R.; Comstock, R.J.; McAtee, K.R.; Thornburg, D.R.

1992-03-01

Twenty-four peripheral rods and two interior rods from North Anna Unit 1, End-of-Cycle 7, were measured at poolside for waterside corrosion on four-cycle Region 6 assemblies F35 and F66, with rod average burnups of 60 GWD/MTU. Similar measurements were obtained on 24 two-cycle fuel rods from Region 8A assemblies H02 and H10 with average burnups of about 40 GWD/MTU. The Region 6 peripheral rods had been corrosion measured previously after three cycles, at 45 GWD/MTU average burnup. The four-cycle Region 6 fuel rods showed high corrosion, compared to only intermediate corrosion level after three cycles. The accelerated corrosion rate in the fourth cycle was accompanied by extensive laminar cracking and spalling of the oxide film in the thickest regions. The peak corrosion of the two-cycle region 8A rods was 32 μm to 53 μm, with some isolated incipient oxide spalling. In conjunction with the in-reactor corrosion measurements, extensive characterization tests plus long-term autoclave corrosion tests were performed on archive samples of the three major tubing lots represented in the North Anna measurements. The autoclave tests generally showed the same ordering of corrosion by tubing lot as in the reactor; the chief difference between the archive tubing samples was a lower tin content (1.38 percent) for the lot with the lowest corrosion rate compared with a higher tin content (1.58) for the lot with the highest corrosion rate. There was no indication in the autoclave tests of an accelerated rate of corrosion as observed in the reactor

Events as Power Source: Wireless Sustainable Corrosion Monitoring

OpenAIRE

Sun, Guodong; Qiao, Guofu; Zhao, Lin; Chen, Zhibo

2013-01-01

This study presents and implements a corrosion-monitoring wireless sensor platform, EPS (Events as Power Source), which monitors the corrosion events in reinforced concrete (RC) structures, while being powered by the micro-energy released from the corrosion process. In EPS, the proposed corrosion-sensing device serves both as the signal source for identifying corrosion and as the power source for driving the sensor mote, because the corrosion process (event) releases electric energy; this is ...

Corrosion Monitors for Embedded Evaluation

Energy Technology Data Exchange (ETDEWEB)

Robinson, Alex L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Pfeifer, Kent B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Casias, Adrian L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Howell, Stephen W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sorensen, Neil R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Missert, Nancy A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-05-01

We have developed and characterized novel in-situ corrosion sensors to monitor and quantify the corrosive potential and history of localized environments. Embedded corrosion sensors can provide information to aid health assessments of internal electrical components including connectors, microelectronics, wires, and other susceptible parts. When combined with other data (e.g. temperature and humidity), theory, and computational simulation, the reliability of monitored systems can be predicted with higher fidelity.

Environmentally Friendly Coating Technology for Autonomous Corrosion Control

Science.gov (United States)

Calle, Luz M.; Li, Wenyan; Buhrow, Jerry W.; Johnsey, Marissa N.; Jolley, Scott T.; Pearman, Benjamin P.; Zhang, Xuejun; Fitzpatrick, Lilliana; Gillis, Mathew; Blanton, Michael;

The corrosion behaviour of galvanized steel in cooling tower water containing a biocide and a corrosion inhibitor.

Science.gov (United States)

Minnoş, Bihter; Ilhan-Sungur, Esra; Çotuk, Ayşın; Güngör, Nihal Doğruöz; Cansever, Nurhan

2013-01-01

The corrosion behaviour of galvanized steel in cooling tower water containing a biocide and a corrosion inhibitor was investigated over a 10-month period in a hotel. Planktonic and sessile numbers of sulphate reducing bacteria (SRB) and heterotrophic bacteria were monitored. The corrosion rate was determined by the weight loss method. The corrosion products were analyzed by energy dispersive X-ray spectroscopy and X-ray diffraction. A mineralized, heterogeneous biofilm was observed on the coupons. Although a biocide and a corrosion inhibitor were regularly added to the cooling water, the results showed that microorganisms, such as SRB in the mixed species biofilm, caused corrosion of galvanized steel. It was observed that Zn layers on the test coupons were completely depleted after 3 months. The Fe concentrations in the biofilm showed significant correlations with the weight loss and carbohydrate concentration (respectively, p < 0.01 and p < 0.01).

Investigations on Microstructure and Corrosion behavior of Superalloy 686 weldments by Electrochemical Corrosion Technique

Science.gov (United States)

Arulmurugan, B.; Manikandan, M.

2018-02-01

In the present study, microstructure and the corrosion behavior of Nickel based superalloy 686 and its weld joints has been investigated by synthetic sea water environment. The weldments were fabricated by Gas Tungsten Arc Welding (GTAW) and Pulsed Current Gas Tungsten Arc Welding (PCGTAW) techniques with autogenous mode and three different filler wires (ERNiCrMo-4, ERNiCrMo-10 and ERNiCrMo-14). Microstructure and Scanning electron microscope examination was carried out to evaluate the structural changes in the fusion zones of different weldments. Energy Dispersive X-ray Spectroscopy (EDS) analysis was carried out to evaluate the microsegregation of alloying elements in the different weld joints. Potentiodynamic polarization study was experimented on the base metal and weld joints in the synthetic sea water environment to evaluate the corrosion rate. Tafel’s interpolation technique was used to obtain the corrosion rate. The microstructure examination revealed that the fine equiaxed dendrites were observed in the pulsed current mode. EDS analysis shows the absence of microsegregation in the current pulsing technique. The corrosion rates of weldments are compared with the base metal. The results show that the fine microstructure with the absence of microsegregation in the PCGTA weldments shows improved corrosion resistance compared to the GTAW. Autogenous PCGTAW shows higher corrosion resistance irrespective of all weldments employed in the present study.

Atmospheric corrosion of metals in industrial city environment.

Science.gov (United States)

Kusmierek, Elzbieta; Chrzescijanska, Ewa

2015-06-01

Atmospheric corrosion is a significant problem given destruction of various materials, especially metals. The corrosion investigation in the industrial city environment was carried out during one year exposure. Corrosion potential was determined using the potentiometric method. The highest effect of corrosion processes was observed during the winter season due to increased air pollution. Corrosion of samples pre-treated in tannic acid before the exposure was more difficult compared with the samples without pretreatment. The corrosion products determined with the SEM/EDS method prove that the most corrosive pollutants present in the industrial city air are SO2, CO2, chlorides and dust.

Acid corrosion inhibitor

Energy Technology Data Exchange (ETDEWEB)

Chen, N G

1964-04-28

An acid corrosion inhibitor is prepared by a 2-stage vacuum evaporation of effluents obtained from the ammonia columns of the coking oven plant. The effluent, leaving a scrubber in which the phenols are removed at a temperature of 98$C, passes through a quartz filter and flows into a heated chamber in which it is used for preheating a solution circulating through a vacuum unit, maintaining the temperature of the solution at 55$ to 60$C. The effluent enters a large tank in which it is boiled at 55$ to 60$C under 635 to 640 mm Hg pressure. Double evaporation of this solution yields a very effective acid corrosion inhibitor. Its corrosion-preventing effect is 97.9% compared with 90.1% for thiourea and 88.5% for urotropin under identical conditions.

LOCAL GENIUS AS SOCIO-CULTURAL CAPITAL FOR EMPOWERING THE BAJO ETHNIC PEOPLE RESIDING AT THE COASTAL AREA OF BUNGIN PERMAI VILLAGE, SOUTH EAST SULAWESI

Directory of Open Access Journals (Sweden)

La Ode Ali Basri

2012-11-01

Full Text Available In this dissertation the local genius as socio-cultural capital for empowering theBajo ethnic people residing at the costal area of Bungin Permai Village, TinanggeaDistrict, South Konawe Regency, South Sulawesi Province is discussed. The Bajo ethnicpeople have a set of local genius within their socio-cultural system which is reflected intheir belief, tradition and custom and is used as the reference for conceiving andexplaining the objective and essence of life and the world. However, such local geniushas not functioned optimally yet as they are still marginalized.This research is focused on (1 what forms of local genius serve as the sociocultural capital for empowering the Bajo ethnic group residing at the coastal area?; (2how the local genius is developed to empower the Bajo ethnic people residing at thecoastal area?; and (3 what factors which may support and obstruct the local genius usedas the socio cultural capital for empowering the Bajo ethnic people residing at the coastalarea? Qualitative method is employed in this study with the approach of cultural studies.The theories used are the post colonial theory, structural theory, generative theory,hegemony theory and semiotic theory. The techniques used for collecting the data neededare participative observation, in-depth interview, library research, and focus groupdiscussion. The data obtained are analytically and descriptively processed and arepresented in the forms of narration, tables and visual illustration.The results of the study show that the Bajo ethnic people residing at BunginPermai Village have a set of local genius which may be potentially used as the sociocultural capital for empowering their community such as (1 indigenous skills andknowledge; (2 working culture; and (3 local organizations. The development of theindigenous skills and knowledge (pengetahuan dan ketrampilan asli; hereon abbreviatedto PKA and the revitalization of their local organizations may be used as the

Natural analogues of nuclear waste glass corrosion

International Nuclear Information System (INIS)

Abrajano, T.A. Jr.; Ebert, W.L.; Luo, J.S.

1999-01-01

This report reviews and summarizes studies performed to characterize the products and processes involved in the corrosion of natural glasses. Studies are also reviewed and evaluated on how well the corrosion of natural glasses in natural environments serves as an analogue for the corrosion of high-level radioactive waste glasses in an engineered geologic disposal system. A wide range of natural and experimental corrosion studies has been performed on three major groups of natural glasses: tektite, obsidian, and basalt. Studies of the corrosion of natural glass attempt to characterize both the nature of alteration products and the reaction kinetics. Information available on natural glass was then compared to corresponding information on the corrosion of nuclear waste glasses, specifically to resolve two key questions: (1) whether one or more natural glasses behave similarly to nuclear waste glasses in laboratory tests, and (2) how these similarities can be used to support projections of the long-term corrosion of nuclear waste glasses. The corrosion behavior of basaltic glasses was most similar to that of nuclear waste glasses, but the corrosion of tektite and obsidian glasses involves certain processes that also occur during the corrosion of nuclear waste glasses. The reactions and processes that control basalt glass dissolution are similar to those that are important in nuclear waste glass dissolution. The key reaction of the overall corrosion mechanism is network hydrolysis, which eventually breaks down the glass network structure that remains after the initial ion-exchange and diffusion processes. This review also highlights some unresolved issues related to the application of an analogue approach to predicting long-term behavior of nuclear waste glass corrosion, such as discrepancies between experimental and field-based estimates of kinetic parameters for basaltic glasses

Natural analogues of nuclear waste glass corrosion.

Energy Technology Data Exchange (ETDEWEB)

Abrajano, T.A. Jr.; Ebert, W.L.; Luo, J.S.

1999-01-06

This report reviews and summarizes studies performed to characterize the products and processes involved in the corrosion of natural glasses. Studies are also reviewed and evaluated on how well the corrosion of natural glasses in natural environments serves as an analogue for the corrosion of high-level radioactive waste glasses in an engineered geologic disposal system. A wide range of natural and experimental corrosion studies has been performed on three major groups of natural glasses: tektite, obsidian, and basalt. Studies of the corrosion of natural glass attempt to characterize both the nature of alteration products and the reaction kinetics. Information available on natural glass was then compared to corresponding information on the corrosion of nuclear waste glasses, specifically to resolve two key questions: (1) whether one or more natural glasses behave similarly to nuclear waste glasses in laboratory tests, and (2) how these similarities can be used to support projections of the long-term corrosion of nuclear waste glasses. The corrosion behavior of basaltic glasses was most similar to that of nuclear waste glasses, but the corrosion of tektite and obsidian glasses involves certain processes that also occur during the corrosion of nuclear waste glasses. The reactions and processes that control basalt glass dissolution are similar to those that are important in nuclear waste glass dissolution. The key reaction of the overall corrosion mechanism is network hydrolysis, which eventually breaks down the glass network structure that remains after the initial ion-exchange and diffusion processes. This review also highlights some unresolved issues related to the application of an analogue approach to predicting long-term behavior of nuclear waste glass corrosion, such as discrepancies between experimental and field-based estimates of kinetic parameters for basaltic glasses.

Atmospheric corrosion of uranium-carbon alloys

International Nuclear Information System (INIS)

Rousset, P.; Accary, A.

1965-01-01

The authors study the corrosion of uranium-carbon alloys having compositions close to that of the mono-carbide; they show that the extent of the observed corrosion effects increases with the water vapour content of the surrounding gas and they conclude that the atmospheric corrosion of these alloys is due essentially to the humidity of the air, the effect of the oxygen being very slight at room temperature. They show that the optimum conditions for preserving U-C alloys are either a vacuum or a perfectly dry argon atmosphere. The authors have also established that the type of corrosion involved is a corrosion which 'cracks under stress' and is transgranular (it can also be intergranular in the case of sub-stoichiometric alloys). They propose, finally, two hypotheses for explaining this mechanism, one of which is illustrated by the existence, at the fissure interface, of corrosion products which can play the role of 'corners' in the mono-carbide grains. (authors) [fr

Corrosion mechanism of copper in palm biodiesel

International Nuclear Information System (INIS)

Fazal, M.A.; Haseeb, A.S.M.A.; Masjuki, H.H.

2013-01-01

Highlights: ► Corrosion of copper in biodiesel increases with the increase of immersion time. ► The corrosion patina is found to be composed of CuO, Cu 2 O, CuCO 3 and Cu(OH) 2 . ► Green CuCO 3 was found as the major corrosion product. ► The mechanisms governing corrosion of copper in palm biodiesel are discussed. - Abstract: Biodiesel is a promising alternative fuel. However, it causes enhanced corrosion of automotive materials, especially of copper based components. In the present study, corrosion mechanism of copper was investigated by scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Compositional change of biodiesel due to the exposure of copper was also investigated. Corrosion patina on copper is found to be composed of Cu 2 O, CuO, Cu(OH) 2 and CuCO 3. Dissolved O 2 , H 2 O, CO 2 and RCOO − radical in biodiesel seem to be the leading factors in enhancing the corrosiveness of biodiesel.

Electrochemical corrosion testing of metal waste forms

International Nuclear Information System (INIS)

Abraham, D. P.; Peterson, J. J.; Katyal, H. K.; Keiser, D. D.; Hilton, B. A.

1999-01-01

Electrochemical corrosion tests have been conducted on simulated stainless steel-zirconium (SS-Zr) metal waste form (MWF) samples. The uniform aqueous corrosion behavior of the samples in various test solutions was measured by the polarization resistance technique. The data show that the MWF corrosion rates are very low in groundwaters representative of the proposed Yucca Mountain repository. Galvanic corrosion measurements were also conducted on MWF samples that were coupled to an alloy that has been proposed for the inner lining of the high-level nuclear waste container. The experiments show that the steady-state galvanic corrosion currents are small. Galvanic corrosion will, hence, not be an important mechanism of radionuclide release from the MWF alloys

Corrosion behaviour of non-ferrous metals in sea water

Energy Technology Data Exchange (ETDEWEB)

Birn, Jerzy; Skalski, Igor [Ship Design and Research Centre, Al. Rzeczypospolitej 8, 80-369 Gdansk (Poland)

2004-07-01

The most typical kinds of corrosion of brasses are selective corrosion (dezincification) and stress corrosion. Prevention against these kinds of corrosion lies in application of arsenic alloy addition and appropriate heat treatment removing internal stresses as well as in maintaining the arsenic and phosphorus contents on a proper level. The most typical corrosion of cupronickels is the local corrosion. Selective corrosion occurs less often and corrosion cracking caused by stress corrosion in sea water does not usually occur. Crevice corrosion is found especially in places of an heterogeneous oxidation of the surface under inorganic deposits or under bio-film. Common corrosive phenomena for brasses and cupronickels are the effects caused by sea water flow and most often the impingement attack. Alloy additions improve resistance to the action of intensive sea water flow but situation in this field requires further improvement, especially if the cheaper kinds of alloys are concerned. Contaminants of sea water such as ammonia and hydrogen sulphide are also the cause of common corrosion processes for all copper alloys. Corrosion of copper alloys may be caused also by sulphate reducing bacteria (SRB). Galvanic corrosion caused by a contact with titanium alloys e.g. in plate heat exchangers may cause corrosion of both kinds copper alloys. Bronzes belong to copper alloys of the highest corrosion resistance. Failures that sometimes occur are caused most often by the cavitation erosion, by an incorrect chemical composition of alloys or at last by their inadequate structure. The main problems of aluminium alloys service in sea water are following phenomena: local corrosion (pitting and crevice corrosion), galvanic corrosion, exfoliation and corrosion in the presence of OH- ions. The cause of local corrosion are caused by presence of passive film on the alloy's surface and presence of chlorides in sea water which are able to damage the passive film. Galvanic corrosion is

Improvement of PWR reliability by corrosion prevention

International Nuclear Information System (INIS)

Takamatsu, Hiroshi

1999-01-01

Since first PWR in Japan started commercial operation in 1970, we have encountered the various modes of corrosion on primary and secondary side components. We have paid much efforts for resolving these corrosion problems, that is, investigating the causes of corrosion and establishing the countermeasures for these corrosion. We summarize these efforts in this article. (author)

New corrosion issues in gas sweetening plants

Energy Technology Data Exchange (ETDEWEB)

Asperger, R.G. (CLI International and Asperger Technologies, Houston, TX (United States))

Gas treating plants are experiencing corrosion problems which impact on efficiency and safety. While general corrosion is not particularly hazardous in the gas processing industry, local corrosion is very dangerous since it has several different mechanisms, all of which have dangerously high rates, and it occurs at locations which are hard to find and hard to predict. A newly discovered, velocity-dependent type of corrosion is reported. It is related to yet-undefined species which cause excessively high corrosion in areas of turbulence. This accelerated corrosion is not due to erosion or cavitation, but to a diffusion-limited reaction accelerated by turbulence. A full-flow test loop was built to evaluate the corrosiveness of gas plant solutions at their normal temperature and flow rates. Test runs were conducted with Co[sub 2]-loaded amine solutions for periods of 12 days. Carbon steel specimens mounted in the test loop were examined and corrosion rates calculated. Chromium alloys were shown to be attacked by corrodents in the low-velocity part of the loop and very aggressively attacked in the high-velocity part. The tests demonstrate the need for rigorous monitoring of corrosion in areas of higher velocity such as piping elbows and other points of turbulence. 5 refs., 2 figs., 3 tabs.

General Corrosion and Localized Corrosion of Waste Package Outer Barrier

Energy Technology Data Exchange (ETDEWEB)

Farmer, J.C.; McCright, R.D.

2000-01-28

Alloy 22 is an extremely Corrosion Resistant Material, with a very stable passive film. Based upon exposures in the LTCTF, the GC rates of Alloy 22 are typically below the level of detection, with four outliers having reported rates up to 0.75 #mu#m per year. In any event, over the 10,000 year life of the repository, GC of the Alloy 22 (assumed to be 2 cm thick) should not be life limiting. Because measured corrosion potentials are far below threshold potentials, localized breakdown of the passive film is unlikely under plausible conditions, even in SSW at 120 deg C. The pH in ambient-temperature crevices formed from Alloy 22 have been determined experimentally, with only modest lowering of the crevice pH observed under plausible conditions. Extreme lowering of the crevice pH was only observed under situations where the applied potential at the crevice mouth was sufficient to result in catastrophic breakdown of the passive film above the threshold potential in non-buffered conditions not characteristic of the Yucca Mountain environment. In cases where naturally ocurring buffers are present in the crevice solution, little or no lowering of the pH was observed, even with significant applied potential. With exposures of twelve months, no evidence of crevice corrosion has been observed in SDW, SCW and SAW at temperatures up to 90 deg C. An abstracted model has been presented, with parameters determined experimentally, that should enable performance assessment to account for the general and localized corrosion of this material. A feature of this model is the use of the materials specification to limit the range of corrosion and threshold potentials, thereby making sure that substandard materials prone to localized attack are avoided. Model validation will be covered in part by a companion SMR on abstraction of this model.

Corrosion of Metal-Matrix Composites with Aluminium Alloy Substrate

Directory of Open Access Journals (Sweden)

B. Bobic

2010-03-01

Full Text Available The corrosion behaviour of MMCs with aluminium alloy matrix was presented. The corrosion characteristics of boron-, graphite-, silicon carbide-, alumina- and mica- reinforced aluminium MMCs were reviewed. The reinforcing phase influence on MMCs corrosion rate as well as on various corrosion forms (galvanic, pitting, stress corrosion cracking, corrosion fatique, tribocorrosion was discussed. Some corrosion protection methods of aluminium based MMCs were described

Mecanismos de licuación y flujo de suelos granulares durante sismos

Directory of Open Access Journals (Sweden)

Adolfo Alarcón Guzmán

1987-09-01

Full Text Available Una amplia evidencia experimental ha mostrado que vibraciones de pequeña amplitud producen una disminución progresiva del volumen en suelos granulares; ello ocurre aún en el caso de arenas densas que podrían dilatar durante carga monotónica o unidireccional bajo un cierto nivel de esfuerzos de confinamiento. Por tanto, cuando un depósito de arena saturada se ve sometido a las ondas de corte que se propagan durante un Sismo, la estructura de la arena tiende a densificarse. Sin embargo, como la duración de aplicación de los esfuerzos de corte cíclicos es, en general, muy pequeña en comparación con el tiempo necesario para que ocurra algún drenaje, la tendencia de la arena a disminuir de volumen durante cada ciclo se refleja en un incremento progresivo de la presión de poros (8,14. Esto produce una reducción continua del esfuerzo efectivo y consecuentemente una disminución en la resistencia al corte de la arena. Una disminución considerable de la resistencia puede conducir a fallas por corte, que en algunas ocasiones son de consecuencias catastróficas.

Corrosion study in molten fluoride salt

International Nuclear Information System (INIS)

Keny, S.J.; Kumbhar, A.G.; Rangarajan, S.; Gupta, V.K.; Maheshwari, N.K.; Vijayan, P.K.

2013-01-01

Corrosion behaviors of two alloys viz. Inconel 625 and Inconel 617 were tested in molten fluoride salts of lithium, sodium and potassium (FLiNaK) in the temperature range of 550-750 ℃ in a nickel lined Inconel vessel. Electrochemical polarization (Tafel plot) technique was used for this purpose. For both alloys, the corrosion rate was found to increase sharply beyond 650 ℃ . At 600 ℃ , Inconel 625 showed a decreasing trend in the corrosion rate over a period of 24 hours, probably due to changes in the surface conditions. After fifteen days, re-testing of Inconel 625 in the same melt showed an increase in the corrosion rate. Inconel 625 was found to be more corrosion resistant than Inconel 617. (author)

Corrosion mechanism applicable to biodegradable magnesium implants

Energy Technology Data Exchange (ETDEWEB)

Atrens, Andrej, E-mail: Andrejs.Atrens@uq.edu.au [University of Queensland, Division of Materials, Brisbane, Qld 4072 (Australia); Liu Ming; Zainal Abidin, Nor Ishida [University of Queensland, Division of Materials, Brisbane, Qld 4072 (Australia)

2011-12-15

Much of our understanding of the Mg corrosion mechanism is based on research using aggressive chloride based solutions like 3% NaCl, which are appropriate for understand the corrosion for applications such as auto construction. The chloride ions tend to cause break down of the partly protective surface film on the Mg alloy surface. The corrosion rate increases with exposure time until steady state is reached, which may take several weeks. An overview is provided of the aspects which determine the corrosion of Mg alloys: (i) measurement details; (ii) impurity elements Fe, Ni, Cu and Co; (iii) second phases; (iv) surface films and surface condition and (v) stress corrosion cracking (SCC). This understanding is used to help understand Mg corrosion for Mg as a biodegradable implant for medical applications. Solutions that elucidate these applications tend to form surface films and the corrosion rate tends to decrease with immersion time.

Corrosion of fuel assembly materials

International Nuclear Information System (INIS)

Noe, M.; Frejaville, G.; Beslu, P.

1985-08-01

Corrosion of zircaloy-4 is reviewed in relation with previsions of improvement in PWRs performance: higher fuel burnup; increase coolant temperature, implying nucleate boiling on the hot clad surfaces; increase duration of the cycle due to load-follow operation. Actual knowledge on corrosion rates, based partly on laboratory tests, is insufficient to insure that external clad corrosion will not constitute a limitation to these improvements. Therefore, additional testing within representative conditions is felt necessary [fr

Experiences of corrosion and corrosion protection in seawater systems in the Nordic countries

International Nuclear Information System (INIS)

Henrikson, S.

1985-01-01

A summary is given of the experience of the corrosion resistance of pumps, heat exchangers, valves and pipings in different seawater cooling systems in Scandinavia, including power reactor cooling systems in Finland and Sweden. For pumps and heat exchangers the experience has been so extensive that a clear picture of today's standing can be given. Owing to scanty data concerning valves and pipes, the survey of the corrosion in these components is less well supported. Vertically extended centrifugal pumps are the pumps in general use in power plant cooling systems. To counteract corrosion on pump riser and pump casing having an organic surface coating, and on stainless steel shafts and impellers, these components should be provided with internal and external cathodic protection. For tube and plate type heat exchangers, titanium has proved to be the best material choice. Rubber-enclosed carbon steel pipings, or pipings having a thick coating of epoxy plastic, have shown very strong corrosion resistance in power plant seawater cooling systems. Valves in seawater systems have primarily been affected by corrosion due to poorly executed or damaged organic coating on cast iron. Different seawater-resistant bronzes (red bronze, tin bronze and aluminium bronze) are therefore preferable as valve materials

Bacillus sp. Acting as Dual Role for Corrosion Induction and Corrosion Inhibition with Carbon Steel (CS

Directory of Open Access Journals (Sweden)

Santosh K. Karn

2017-10-01

Full Text Available Present work investigated the role of five different bacteria species as a corrosion inducer as well as corrosion inhibitor with carbon steel (CS. We observed the ability of different bacteria species on the metal surface attachment, biofilm formation, and determined Peroxidase, Catalase enzyme activity in the detached biofilm from the CS surface. We found that each strain has diverse conduct for surface attachment like DS1 3.3, DS2 2.5, DS3 4.3, DS4 4.0, and DS5 4.71 log cfu/cm2 and for biofilm 8.3 log cfu/cm2. The enzyme Peroxidase, Catalase was found in huge concentration inside the biofilm Peroxidase was maximum for DS4 36.0 U/ml and least for DS3 19.54 U/ml. Whereas, Catalase was highest for DS4, DS5 70.14 U/ml and least 57.2 U/ml for DS2. Scanning electron microscopy (SEM was conducted to examine the biofilm and electrochemical impedance spectroscopy (EIS were utilized to observe corrosion in the presence of bacteria. The electrochemical results confirmed that DS1, DS3, DS4, and DS5 strains have statistically significant MIC-factors (Microbially Influenced Corrosion of 5.46, 8.51, 2.36, and 1.04, while DS2 protective effect factor of 0.89. Weight reduction results with carbon steel likewise supports that corrosion was initiated by DS1 and DS3, while DS2 and DS5 have no any impact though with DS4 we watched less weight reduction however assumed no role in the corrosion. We established the relation of Peroxidase enzyme activity of the isolates. DS1, DS3 and having Peroxidase in the range 22.18, 19.54 U/ml which induce the corrosion whereas DS2 and DS5 having 28.57 and 27.0 U/ml has no any effect and DS4 36 U/ml has inhibitory effect, increasing concentration inhibiting the corrosion. For Catalase DS1, DS3 have 67.28, 61.57 U/ml which induce corrosion while DS2 and DS5 57.71 and 59.14 U/ml also has no effect whereas DS4 70.14 U/ml can inhibit corrosion. Results clearly express that in a specific range both enzymes can induce the corrosion

PLANTS AS A SOURCE OF GREEN CORROSION INHIBITORS ...

African Journals Online (AJOL)

Mgina

Acacia senegal) exhibit good inhibition characteristics to corrosion on mild steel under fresh water medium and the ... as corrosion inhibitors for metals in various corrosive media ..... alloy corrosion in chloride solution", J. Appl. Electrochem.

Atmospheric corrosion of metals in industrial city environment

Directory of Open Access Journals (Sweden)

Elzbieta Kusmierek

2015-06-01

Full Text Available Atmospheric corrosion is a significant problem given destruction of various materials, especially metals. The corrosion investigation in the industrial city environment was carried out during one year exposure. Corrosion potential was determined using the potentiometric method. The highest effect of corrosion processes was observed during the winter season due to increased air pollution. Corrosion of samples pre-treated in tannic acid before the exposure was more difficult compared with the samples without pretreatment. The corrosion products determined with the SEM/EDS method prove that the most corrosive pollutants present in the industrial city air are SO2, CO2, chlorides and dust.

Materials corrosion and protection at high temperatures

International Nuclear Information System (INIS)

Balbaud, F.; Desgranges, Clara; Martinelli, Laure; Rouillard, Fabien; Duhamel, Cecile; Marchetti, Loic; Perrin, Stephane; Molins, Regine; Chevalier, S.; Heintz, O.; David, N.; Fiorani, J.M.; Vilasi, M.; Wouters, Y.; Galerie, A.; Mangelinck, D.; Viguier, B.; Monceau, D.; Soustelle, M.; Pijolat, M.; Favergeon, J.; Brancherie, D.; Moulin, G.; Dawi, K.; Wolski, K.; Barnier, V.; Rebillat, F.; Lavigne, O.; Brossard, J.M.; Ropital, F.; Mougin, J.

2011-01-01

This book was made from the lectures given in 2010 at the thematic school on 'materials corrosion and protection at high temperatures'. It gathers the contributions from scientists and engineers coming from various communities and presents a state-of-the-art of the scientific and technological developments concerning the behaviour of materials at high temperature, in aggressive environments and in various domains (aerospace, nuclear, energy valorization, and chemical industries). It supplies pedagogical tools to grasp high temperature corrosion thanks to the understanding of oxidation mechanisms. It proposes some protection solutions for materials and structures. Content: 1 - corrosion costs; macro-economical and metallurgical approach; 2 - basic concepts of thermo-chemistry; 3 - introduction to the Calphad (calculation of phase diagrams) method; 4 - use of the thermodynamic tool: application to pack-cementation; 5 - elements of crystallography and of real solids description; 6 - diffusion in solids; 7 - notions of mechanics inside crystals; 8 - high temperature corrosion: phenomena, models, simulations; 9 - pseudo-stationary regime in heterogeneous kinetics; 10 - nucleation, growth and kinetic models; 11 - test experiments in heterogeneous kinetics; 12 - mechanical aspects of metal/oxide systems; 13 - coupling phenomena in high temperature oxidation; 14 - other corrosion types; 15 - methods of oxidized surfaces analysis at micro- and nano-scales; 16 - use of SIMS in the study of high temperature corrosion of metals and alloys; 17 - oxidation of ceramics and of ceramic matrix composite materials; 18 - protective coatings against corrosion and oxidation; 19 - high temperature corrosion in the 4. generation of nuclear reactor systems; 20 - heat exchangers corrosion in municipal waste energy valorization facilities; 21 - high temperature corrosion in oil refining and petrochemistry; 22 - high temperature corrosion in new energies industry. (J.S.)

Long Term Corrosion/Degradation Test Six Year Results

Energy Technology Data Exchange (ETDEWEB)

M. K. Adler Flitton; C. W. Bishop; M. E. Delwiche; T. S. Yoder

2004-09-01

The Subsurface Disposal Area (SDA) of the Radioactive Waste Management Complex (RWMC) located at the Idaho National Engineering and Environmental Laboratory (INEEL) contains neutron-activated metals from non-fuel, nuclear reactor core components. The Long-Term Corrosion/Degradation (LTCD) Test is designed to obtain site-specific corrosion rates to support efforts to more accurately estimate the transfer of activated elements to the environment. The test is using two proven, industry-standard methods—direct corrosion testing using metal coupons, and monitored corrosion testing using electrical/resistance probes—to determine corrosion rates for various metal alloys generally representing the metals of interest buried at the SDA, including Type 304L stainless steel, Type 316L stainless steel, Inconel 718, Beryllium S200F, Aluminum 6061, Zircaloy-4, low-carbon steel, and Ferralium 255. In the direct testing, metal coupons are retrieved for corrosion evaluation after having been buried in SDA backfill soil and exposed to natural SDA environmental conditions for times ranging from one year to as many as 32 years, depending on research needs and funding availability. In the monitored testing, electrical/resistance probes buried in SDA backfill soil will provide corrosion data for the duration of the test or until the probes fail. This report provides an update describing the current status of the test and documents results to date. Data from the one-year and three-year results are also included, for comparison and evaluation of trends. In the six-year results, most metals being tested showed extremely low measurable rates of general corrosion. For Type 304L stainless steel, Type 316L stainless steel, Inconel 718, and Ferralium 255, corrosion rates fell in the range of “no reportable” to 0.0002 mils per year (MPY). Corrosion rates for Zircaloy-4 ranged from no measurable corrosion to 0.0001 MPY. These rates are two orders of magnitude lower than those specified in

Evaluation of Encapsulated Inhibitor for Autonomous Corrosion Protection

Science.gov (United States)

Johnsey, M. N.; Li, W.; Buhrow, J. W.; Calle, L. M.; Pearman, B. P.; Zhang, X.

2015-01-01

This work concerns the development of smart coating technologies based on microencapsulation for the autonomous control of corrosion. Microencapsulation allows the incorporation of corrosion inhibitors into coating which provides protection through corrosion-controlled release of these inhibitors.One critical aspect of a corrosion protective smart coating is the selection of corrosion inhibitor for encapsulation and comparison of the inhibitor function before and after encapsulation. For this purpose, a systematic approach is being used to evaluate free and encapsulated corrosion inhibitors by salt immersion. Visual, optical microscope, and Scanning Electron Microscope (with low-angle backscatter electron detector) are used to evaluate these inhibitors. It has been found that the combination of different characterization tools provide an effective method for evaluation of early stage localized corrosion and the effectiveness of corrosion inhibitors.

Liquid metal corrosion considerations in alloy development

International Nuclear Information System (INIS)

Tortorelli, P.F.; DeVan, J.H.

1984-01-01

Liquid metal corrosion can be an important consideration in developing alloys for fusion and fast breeder reactors and other applications. Because of the many different forms of liquid metal corrosion (dissolution, alloying, carbon transfer, etc.), alloy optimization based on corrosion resistance depends on a number of factors such as the application temperatures, the particular liquid metal, and the level and nature of impurities in the liquid and solid metals. The present paper reviews the various forms of corrosion by lithium, lead, and sodium and indicates how such corrosion reactions can influence the alloy development process

Recent Developments on Autonomous Corrosion Protection Through Encapsulation

Science.gov (United States)

Li, W.; Buhrow, J. W.; Calle, L. M.; Gillis, M.; Blanton, M.; Hanna, J.; Rawlins, J.

2015-01-01

This paper concerns recent progress in the development of a multifunctional smart coating, based on microencapsulation, for the autonomous detection and control of corrosion. Microencapsulation has been validated and optimized to incorporate desired corrosion control functionalities, such as early corrosion detection and inhibition, through corrosion-initiated release of corrosion indicators and inhibitors, as well as self-healing agent release triggered by mechanical damage. While proof-of-concept results have been previously reported, more recent research and development efforts have concentrated on improving coating compatibility and synthesis procedure scalability, with a targeted goal of obtaining easily dispersible pigment-grade type microencapsulated materials. The recent progress has resulted in the development of pH-sensitive microparticles as a corrosion-triggered delivery system for corrosion indicators and inhibitors. The synthesis and early corrosion indication results obtained with coating formulations that incorporate these microparticles are reported. The early corrosion indicating results were obtained with color changing and with fluorescent indicators.

Corrosion of carbon steel in contact with bentonite

International Nuclear Information System (INIS)

Dobrev, D.; Vokal, A.; Bruha, P.

2010-01-01

Document available in extended abstract form only. Carbon steel canisters were chosen in a number of disposal concepts as reference material for disposal canisters. The corrosion rates of carbon steels in water solution both in aerobic and anaerobic conditions are well known, but only scarce data are available for corrosion behaviour of carbon steels in contact with bentonite. A special apparatus, which enables to measure corrosion rate of carbon steels under conditions simulating conditions in a repository, namely in contact with bentonite under high pressure and elevated temperatures was therefore prepared to study: - Corrosion rate of carbon steels in direct contact with bentonite in comparison with corrosion rate of carbon steels in synthetic bentonite pore water. - Influence of corrosion products on bentonite. The apparatus is composed of corrosion chamber containing a carbon steel disc in direct contact with compacted bentonite. Synthetic granitic water is above compacted bentonite under high pressure (50 - 100 bar) to simulate hydrostatic pressure in a repository. The experiments can be carried out under various temperatures. Bentonites used for experiments were Na-type of bentonite Volclay KWK 80 - 20 and Ca-Mg Czech bentonite from deposit Rokle. Before adding water into corrosion system the corrosion chamber was purged by nitrogen gas. The saturation of bentonite and corrosion rate were monitored by measuring consumption of water, pressure increase caused by swelling pressure of bentonite and by generation of hydrogen. Corrosion rate was also determined after corrosion experiments from weight loss of samples. The results of experiments show that the corrosion behaviour of carbon steels in contact with bentonite is very different from corrosion of carbon steels in water simulating bentonite pore water solution. The corrosion rates of carbon steel in contact with bentonite reached after 30 days of corrosion the values approaching 40 mm/yr contrary to values

Aluminum Corrosion and Turbidity

International Nuclear Information System (INIS)

Longtin, F.B.

2003-01-01

Aluminum corrosion and turbidity formation in reactors correlate with fuel sheath temperature. To further substantiate this correlation, discharged fuel elements from R-3, P-2 and K-2 cycles were examined for extent of corrosion and evidence of breaking off of the oxide film. This report discusses this study

Kinetics of steel corrosion in water

International Nuclear Information System (INIS)

Vettegren', V.I.; Bashkarev, A.Ya.; Danchukov, K.G.; Morozov, G.I.

2003-01-01

Kinetics of corrosion damage accumulation in steels of different composition (Cr-Ni-Mo-Ti, Cr-Ni-Mn-N-V, Cr-Ni-N-Mn-Mo, Cr-Ni-Nb, Cr-Ni-Ti, Cr-Mn-Ni, Mn-Al-Nb-Si, Mn-Cr-Al-Si and Mn-Al-Si) in NaCl solution and in sea water was studied. It is shown that degree of corrosion damage relates to time according to the first order reaction expression. The values of corrosion activation energy and of parameter characterizing protection properties of corrosion film are determined [ru

Corrosion inhibition

Energy Technology Data Exchange (ETDEWEB)

Fisher, A O

1965-12-29

An acid corrosion-inhibiting composition consists essentially of a sugar, and an alkali metal salt selected from the group consisting of iodides and bromides. The weight ratio of the sugar to the alkali metal salt is between 2:1 and about 20,000:1. Also, a corrosion- inhibited phosphoric acid composition comprising at least about 20 wt% of phosphoric acid and between about 0.1 wt% and about 10 wt% of molasses, and between about 0.0005 wt% and about 1 wt% of potassium iodide. The weight ratio of molasses to iodide is greater than about 2:1. (11 claims)

Corrosion protection of reusable surgical instruments.

Science.gov (United States)

Shah, Sadiq; Bernardo, Mildred

2002-01-01

To understand the corrosion properties of surgical scissors, 416 stainless steel disks and custom electrodes were used as simulated surfaces under various conditions. These simulated surfaces were exposed to tap water and 400-ppm synthetic hard water as Ca2CO3 under different conditions. The samples were evaluated by various techniques for corrosion potential and the impact of environmental conditions on the integrity of the passive film. The electrodes were used to monitor the corrosion behavior by potentiodynamic polarization technique in water both in the presence and absence of a cleaning product. The surface topography of the 416 stainless steel disks was characterized by visual observations and scanning electron microscopy (SEM), and the surface chemistry of the passive film on the surface of the scissors was characterized by x-ray photoelectron spectroscopy (XPS). The results suggest that surgical instruments made from 416 stainless steel are not susceptible to uniform corrosion; however, they do undergo localized corrosion. The use of suitable cleaning products can offer protection against localized corrosion during the cleaning step. More importantly, the use of potentiodynamic polarization techniques allowed for a quick and convenient approach to evaluate the corrosion properties of surgical instruments under a variety of simulated-use environmental conditions.

Corrosion of aluminium in soft drinks.

Science.gov (United States)

Seruga, M; Hasenay, D

1996-04-01

The corrosion of aluminium (Al) in several brands of soft drinks (cola- and citrate-based drinks) has been studied, using an electrochemical method, namely potentiodynamic polarization. The results show that the corrosion of Al in soft drinks is a very slow, time-dependent and complex process, strongly influenced by the passivation, complexation and adsorption processes. The corrosion of Al in these drinks occurs principally due to the presence of acids: citric acid in citrate-based drinks and orthophosphoric acid in cola-based drinks. The corrosion rate of Al rose with an increase in the acidity of soft drinks, i.e. with increase of the content of total acids. The corrosion rates are much higher in the cola-based drinks than those in citrate-based drinks, due to the facts that: (1) orthophosphoric acid is more corrosive to Al than is citric acid, (2) a quite different passive oxide layer (with different properties) is formed on Al, depending on whether the drink is cola or citrate based. The method of potentiodynamic polarization was shown as being very suitable for the study of corrosion of Al in soft drinks, especially if it is combined with some non-electrochemical method, e.g. graphite furnace atomic absorption spectrometry (GFAAS).

Evolutionary Computation Techniques for Predicting Atmospheric Corrosion

Directory of Open Access Journals (Sweden)

Amine Marref

2013-01-01

Full Text Available Corrosion occurs in many engineering structures such as bridges, pipelines, and refineries and leads to the destruction of materials in a gradual manner and thus shortening their lifespan. It is therefore crucial to assess the structural integrity of engineering structures which are approaching or exceeding their designed lifespan in order to ensure their correct functioning, for example, carrying ability and safety. An understanding of corrosion and an ability to predict corrosion rate of a material in a particular environment plays a vital role in evaluating the residual life of the material. In this paper we investigate the use of genetic programming and genetic algorithms in the derivation of corrosion-rate expressions for steel and zinc. Genetic programming is used to automatically evolve corrosion-rate expressions while a genetic algorithm is used to evolve the parameters of an already engineered corrosion-rate expression. We show that both evolutionary techniques yield corrosion-rate expressions that have good accuracy.

Predicting the Performance of Organic Corrosion Inhibitors

Directory of Open Access Journals (Sweden)

David A. Winkler

2017-12-01

Full Text Available The withdrawal of effective but toxic corrosion inhibitors has provided an impetus for the discovery of new, benign organic compounds to fill that role. Concurrently, developments in the high-throughput synthesis of organic compounds, the establishment of large libraries of available chemicals, accelerated corrosion inhibition testing technologies, and the increased capability of machine learning methods have made discovery of new corrosion inhibitors much faster and cheaper than it used to be. We summarize these technical developments in the corrosion inhibition field and describe how data-driven machine learning methods can generate models linking molecular properties to corrosion inhibition that can be used to predict the performance of materials not yet synthesized or tested. We briefly summarize the literature on quantitative structure–property relationships models of small organic molecule corrosion inhibitors. The success of these models provides a paradigm for rapid discovery of novel, effective corrosion inhibitors for a range of metals and alloys in diverse environments.

Improvements in zirconium alloy corrosion resistance

International Nuclear Information System (INIS)

Kilp, G.R.; Thornburg, D.R.; Comstock, R.J.

1990-01-01

The corrosion rates of a series of Zircaloy 4 and Zr-Nb alloys were evaluated in long-term (exceeding 500 days in some cases) autoclave tests. The testing was done at various conditions including 633 K (680 F) water, 633 K (650 F) water, 633 k (680 F) lithiated water (70 PPM/0.01 molal lithium), and 673 K (750 F) steam. Materials evaluated are from the following three groups: (1) standard Zircaloy 4; (2) Zircaloy 4 with tightened controls on chemistry limits and heat-treatment history; and (3) Zr-Nb alloys. To optimize the corrosion resistance of the Zircaloy 4 material, the effects of specific chemistry controls (tighter limits on nitrogen, oxygen, silicon, carbon and tin) were evaluated. Also the effects of the thermal history, as measured by integrated annealing of ''A'' time were determined. The ''A'' times ranged from 0.1x10 -18 (h) to 46x10 -18 (h). A material referred to as ''Improved Zircaloy 4'', having optimized chemistry and ''A'' time levels for reduced corrosion, has been developed and tested. This material has a reduced and more uniform corrosion rate compared to the prior Zircaloy 4 material. Alternative alloys were also evaluated for potential improvement in cladding corrosion resistance. ZIRLO TM material was chosen for development and has been included in the long-term corrosion testing. Demonstration fuel assemblies using ZIRLO cladding are now operating in a commercial reactor. The results for the various test conditions and compositions are reported and the relative corrosion characteristics summarized. Based on the BR-3 data, there is a ranking correspondence between in-reactor corrosion and autoclave testing in lithiated water. In particular, the ZIRLO material has significantly improved relative corrosion resistance in the lithiated water tests. Reduced Zircaloy-4 corrosion rates are also obtained from the tighter controls on the chemistry (specifically lower tin, nitrogen, and carbon; higher silicon; and reduced oxygen variability) and ''A

Corrosion of bare and galvanized steel in gypsum

Directory of Open Access Journals (Sweden)

Gómez, Mercedes

1988-12-01

Full Text Available Gypsum is a relatively low-cost building material much abounding in our country. When it is put in contact with steel, it may produce high corrosion rates due to its pH value (close to 7. This work reports the results obtained in studying the corrosion rates of bare and galvanized steel in contact with gypsum and plaster, as well as the influence curing thermal treatment applied to gypsum, enviromental relative humidity and addition of compounds with different natures and purposes may have in such process. In-situ observations, as well as the measurement of the Polarization Resistance and the weight loss have been used as measurement technics. From the results obtained it has been possible to deduce that galvanized steel has better behaviour in dry enviroments than bare steel in the same conditions and moist atmosphere induces proportionally more corrosion in galvanized steel than in bare one. Additions to gypsum do not modified these conclusions, though it may be pointed out that addition of nitrites or lime improves the behaviour of bare steel, while galvanized behaviour is not modified. The addition of lime is not recommended because phenomena of dilated along time expansion may take place.

El yeso es un material de construcción de relativo bajo coste y que, además, es muy abundante en nuestro país. Debido a su pH cercano a la neutralidad, cuando entra en contacto con el acero, este puede corroerse a elevadas velocidades. En esta comunicación se presentan los resultados de un estudio sobre la velocidad de corrosión del acero desnudo y galvanizado en contacto con yeso y escayola y la influencia que tienen: el tratamiento térmico del curado del yeso, la humedad relativa ambiental y la adición de aditivos de diversa naturaleza y finalidad. Como técnicas de medida se han utilizado la medida de la Resistencia de Polarización y de la pérdida de peso, así como observaciones visuales. De los resultados se puede deducir que en

Limitación del esfuerzo terapéutico y principios bioéticos en la toma de decisiones

Directory of Open Access Journals (Sweden)

Gilberto de Jesús Betancourt Betancourt

Full Text Available Se realiza un estudio de los principios básicos o tradicionales de la bioética y su influencia en la práctica de la limitación del esfuerzo terapéutico en las Unidades de Cuidados Intensivos, como condicionante que favorece su aplicación en los pacientes en estado terminal. Se aborda la necesidad de una bioética no importada de otros países, que se corresponda a las características de la realidad latinoamericana y a cada contexto sociocultural. El trabajo tiene como objetivo fundamental resaltar la importancia de estos principios básicos en la discusión ético-clínica para la toma de decisiones, a partir de una bioética que se corresponda a la realidad de los sistemas imperantes.

Corrosion of reactor materials

Energy Technology Data Exchange (ETDEWEB)

NONE

1963-01-15

Much operational experience and many experimental results have accumulated in recent years regarding corrosion of reactor materials, particularly since the 1958 Geneva Conference on the Peaceful Uses of Atomic Energy, where these problems were also discussed. It was, felt that a survey and critical appraisal of the results obtained during this period had become necessary and, in response to this need, IAEA organized a Conference on the Corrosion of Reactor Materials at Salzburg, Austria (4-9 June 1962). It covered many of the theoretical, experimental and engineering problems relating to the corrosion phenomena which occur in nuclear reactors as well as in the adjacent circuits

Comportamiento del índice de bajo peso al nacer en el Policlínico Docente Cerro durante los años 2009-2010

Directory of Open Access Journals (Sweden)

Ramona Moraima Torres Zulueta

Full Text Available Introducción: el bajo peso al nacerconstituye el índice predictivo más importante de la mortalidad infantil y se plantea que es 20 veces mayor que en el recién nacido con peso adecuado. Objetivo: comparar el comportamiento del índice de bajo peso al nacer en recién nacidos de un Policlínico durante los años 2009 y 2010. Método: se realizó un estudio comparativo de tipo descriptivo en el Policlínico Universitario Cerro, en la provincia La Habana, durante los años 2009 y 2010. El Universo estuvo constituido por los 350 recién nacidos vivos en el 2009 y los 318 en el 2010, y la muestra estuvo conformada por 23 niños con bajo peso al nacer en el 2009 y por 21 en el 2010. Se revisaron las historias obstétricas de las madres y se identificaron algunas variables socio-demográficas. Resultados: en ambos años estudiados la edad materna de mayor bajo peso al nacer fue de 20 a 34 años, con 73,9 y 80,9 %. Los factores de riesgo que se asociaron al bajo peso fueron: el hábito de fumar, que predominó en ambos años de estudio, representado por un 60,8 % en 2009 y por un 61,9 % en el 2010; el trastorno hipertensivo, con un 35 % en el año 2010 y un 27,7 % en el año 2009, y en ambos años fue superior en el grupo de gestantes con hipertensión arterial crónica. La anemia aumentó considerablemente en el 2010 en un 80,9 %, comparado con un 69,5 % en el año 2009. Conclusiones: el bajo peso al nacer resultó más frecuente en las gestantes de 20 a 34 años. Los factores de riesgo asociados al bajo peso al nacer con mayor frecuencia fueron: la anemia, el hábito de fumar y los trastornos hipertensivos.

Crevice Corrosion on Ni-Cr-Mo Alloys

International Nuclear Information System (INIS)

P. Jakupi; D. Zagidulin; J.J. Noel; D.W. Shoesmith

2006-01-01

Ni-Cr-Mo alloys were developed for their exceptional corrosion resistance in a variety of extreme corrosive environments. An alloy from this series, Alloy-22, has been selected as the reference material for the fabrication of nuclear waste containers in the proposed Yucca Mountain repository located in Nevada (US). A possible localized corrosion process under the anticipated conditions at this location is crevice corrosion. therefore, it is necessary to assess how this process may, or may not, propagate if the use of this alloy is to be justified. Consequently, the primary objective is the development of a crevice corrosion damage function that can be used to assess the evolution of material penetration rates. They have been using various electrochemical methods such as potentiostatic, galvanostatic and galvanic coupling techniques. Corrosion damage patterns have been investigated using surface analysis techniques such as scanning electron microscopy (SEM) and optical microscopy. All crevice corrosion experiments were performed at 120 C in 5M NaCl solution. Initiating crevice corrosion on these alloys has proven to be difficult; therefore, they have forced it to occur under either potentiostatic or galvanostatic conditions

Corrosion of porous silicon in tetramethylammonium hydroxide solution

International Nuclear Information System (INIS)

Lai, Chuan; Li, Xue-Ming; Zou, Li-Ke; Chen, Qiang; Xie, Bin; Li, Yu-Lian; Li, Xiao-Lin; Tao, Zhi

2014-01-01

Highlights: • The corrosion of porous silicon in (CH 3 ) 4 NOH solution was studied. • The residue of corrosion products was a mixture of [(CH 3 ) 4 N] 2 SiO 3 and SiO 2 . • The effect factors for porous silicon corrosion were elaborately investigated. • The additive of ethanol in (CH 3 ) 4 NOH solution could reduce the corrosion rate. • The 1.0 M (CH 3 ) 4 NOH could act as an applicable and novel corrosion solution. - Abstract: Corrosion of porous silicon in tetramethylammonium hydroxide (TMAH) solution was studied using weight loss measurements and scanning electron microscope. The effects of temperature, concentration of TMAH and volume ratio of ethanol in 1.0 M TMAH on corrosion rate and corrosion time were elaborately investigated. The residue of corrosion products were characterized as a mixture of [(CH 3 ) 4 N] 2 SiO 3 and SiO 2 . A comparative test among TMAH, KOH and NaOH illustrated that the 1.0 M TMAH could act as an applicable and novel corrosion solution to remove porous silicon layer for determining the porosity of porous silicon

Passive Corrosion Behavior of Alloy 22

International Nuclear Information System (INIS)

R.B. Rebak; J.H. Payer

2006-01-01

Alloy 22 (NO6022) was designed to stand the most aggressive industrial applications, including both reducing and oxidizing acids. Even in the most aggressive environments, if the temperature is lower than 150 F (66 C) Alloy 22 would remain in the passive state having particularly low corrosion rates. In multi-ionic solutions that may simulate the behavior of concentrated ground water, even at near boiling temperatures, the corrosion rate of Alloy 22 is only a few nano-meters per year because the alloy is in the complete passive state. The corrosion rate of passive Alloy 22 decreases as the time increases. Immersion corrosion testing also show that the newer generation of Ni-Cr-Mo alloys may offer a better corrosion resistance than Alloy 22 only in some highly aggressive conditions such as in hot acids

High Temperature Corrosion on Biodust Firing

DEFF Research Database (Denmark)

Okoro, Sunday Chukwudi

The high content of alkali metals and chlorine in biomass gives rise to fouling/slagging and corrosion of heat exchange components, such as superheaters, in biomass fired power plants. Increasing the lifetime of these components, and in addition, preventing unwarranted plant shutdowns due...... to their failure, requires understanding of the complex corrosion mechanisms, as well as development of materials that are resistant to corrosion under biomass firing conditions, thereby motivating the current work. To understand the mechanisms of corrosion attack, comprehensive analysis of corrosion products...... by the combined use of complementary information from microscopy, energy dispersive X-ray spectroscopy and various X-ray diffraction characterization techniques. In light of the wide variation in operating conditions in biomass fired power plants, systematic and well-controlled, but realistic laboratory scale...

Corrosion and Corrosion-Fatigue Behavior of 7075 Aluminum Alloys Studied by In Situ X-Ray Tomography

Science.gov (United States)

Stannard, Tyler

7XXX Aluminum alloys have high strength to weight ratio and low cost. They are used in many critical structural applications including automotive and aerospace components. These applications frequently subject the alloys to static and cyclic loading in service. Additionally, the alloys are often subjected to aggressive corrosive environments such as saltwater spray. These chemical and mechanical exposures have been known to cause premature failure in critical applications. Hence, the microstructural behavior of the alloys under combined chemical attack and mechanical loading must be characterized further. Most studies to date have analyzed the microstructure of the 7XXX alloys using two dimensional (2D) techniques. While 2D studies yield valuable insights about the properties of the alloys, they do not provide sufficiently accurate results because the microstructure is three dimensional and hence its response to external stimuli is also three dimensional (3D). Relevant features of the alloys include the grains, subgrains, intermetallic inclusion particles, and intermetallic precipitate particles. The effects of microstructural features on corrosion pitting and corrosion fatigue of aluminum alloys has primarily been studied using 2D techniques such as scanning electron microscopy (SEM) surface analysis along with post-mortem SEM fracture surface analysis to estimate the corrosion pit size and fatigue crack initiation site. These studies often limited the corrosion-fatigue testing to samples in air or specialized solutions, because samples tested in NaCl solution typically have fracture surfaces covered in corrosion product. Recent technological advancements allow observation of the microstructure, corrosion and crack behavior of aluminum alloys in solution in three dimensions over time (4D). In situ synchrotron X-Ray microtomography was used to analyze the corrosion and cracking behavior of the alloy in four dimensions to elucidate crack initiation at corrosion pits

Corrosion and Wear Analysis in Marine Transport Constructions

OpenAIRE

Urbahs, A; Savkovs, K; Rijkuris, G; Andrejeva, D

2018-01-01

Corrosion is one of the most common naturally occurring processes studied by thermodynamics, which includes oxidation process, metal disruption, and its chemical and electrochemical effects under environmental influence. Corrosion of metal and equipment accounts for a considerable proportion of total corrosion losses, thus providing the impetus for further investigation and developments related to corrosion protection in order to provide transport systems and industry with corrosion preventiv...

Corrosion detection of nanowires by magnetic sensors

KAUST Repository

Kosel, Jü rgen; Amara, Selma; Ivanov, Iurii; Blanco, Mario

2017-01-01

Disclosed are various embodiments related to a corrosion detection device for detecting corrosive environments. A corrosion detection device comprises a magnetic sensor and at least one magnetic nanowire disposed on the magnetic sensor. The magnetic sensor is configured to detect corrosion of the one or more magnetic nanowires based at least in part on a magnetic field of the one or more magnetic nanowires.

Corrosion detection of nanowires by magnetic sensors

KAUST Repository

Kosel, Jürgen

2017-10-05

Disclosed are various embodiments related to a corrosion detection device for detecting corrosive environments. A corrosion detection device comprises a magnetic sensor and at least one magnetic nanowire disposed on the magnetic sensor. The magnetic sensor is configured to detect corrosion of the one or more magnetic nanowires based at least in part on a magnetic field of the one or more magnetic nanowires.

Proyecto de factibilidad para la creación de una Unidad Educativa Particular en el cantón Riobamba provincia de Chimborazo.

OpenAIRE

Logroño Satán, Viviana del Pilar

2015-01-01

El analfabetismo, bajo nivel de escolaridad, tasas de repetición deserción escolar, deficiente infraestructura educativa han sido factores que durante los últimos años han afectado la educación en el Ecuador, todos los esfuerzos que se puedan realizar para eliminar esta realidad serán provechosos para el desarrollo del país. Durante los últimos años se ha evidenciado una serie de problemas e ineficiencias en el sector educativo del país haciendo cada vez más evidente la necesidad de un cambio...

Educación para el amor: una necesidad impostergable

OpenAIRE

Gerardo Alonso Steele-Zúñiga

2001-01-01

Este artículo reconoce los esfuerzos hechos en Costa Rica, concernientes a la Educación Sexual. Señala, también, el bajo nivel de logro en este campo, debido a la falta de coordinación entre las instituciones y las personas preocupadas por la Educación Sexual. Y lo más, importante, propone trabajar fuertemente en Educación para el Amor, enfatizando en los principios éticos y filosóficos del Amor, como los fundamentos de la educación de la sexualidad y el sexo.

Modelización de Terrenos Granulares Sometidos a Gran Número de Ciclos de Carga

OpenAIRE

Illueca Jové, Manuel

2011-01-01

El presente trabajo describe el proceso llevado a cabo para la obtención de los asientos producidos por la cimentación de un equipo dinámico sobre un terreno granular. En primer lugar, comenzamos obteniendo los esfuerzos dinámicos transmitidos por el equipo y la cimentación al terreno. Posteriormente, modelizaremos el comportamiento del terreno bajo esta carga dinámica para obtener los asientos producidos. Principalmente este trabajo se centra en la obtención de la deformación que sufre un te...

Nueva ruralidad: usos, funciones y actividades. Dinámicas y problemáticas

OpenAIRE

Zuluaga Sánchez, Gloria Patricia

2002-01-01

Resumen: el trabajo que aquí se presenta, constituye un esfuerzo por problematizar las nociones de lo "rural" y la "ruralidad", guiado en buena medida por la reflexión y el análisis de las preguntas más recurrentes en las asignaturas que han estado bajo mi responsabilidad en la Universidad Nacional. Por lo tanto el documento propone una discusión sobre dichos conceptos y categorías, retomando tanto los enfoques tradicionales como actuales, los cuales se ilustran con ejemplos sobre las implica...

Corrosion potential monitoring in nuclear power environments

International Nuclear Information System (INIS)

Molander, A.

2004-01-01

Full text of publication follows: corrosion monitoring. The corrosion potential is usually an important parameter or even the prime parameter for many types of corrosion processes. One typical example of the strong influence of the corrosion potential on corrosion performance is stress corrosion of sensitized stainless steel in pure high temperature water corresponding to boiling water conditions. The use of in-plant monitoring to follow the effect of hydrogen addition to mitigate stress corrosion in boiling water reactors is now a well-established technique. However, different relations between the corrosion potential of stainless steel and the oxidant concentration have been published and only recently an improved understanding of the electrochemical reactions and other conditions that determine the corrosion potential in BWR systems have been reached. This improved knowledge will be reviewed in this paper. Electrochemical measurements has also been performed in PWR systems and mainly the feedwater system on the secondary side of PWRs. The measurements performed so far have shown that electrochemical measurements are a very sensitive tool to detect and follow oxygen transients in the feedwater system. Also determinations of the minimum hydrazine dosage to the feedwater have been performed. However, PWR secondary side monitoring has not yet been utilized to the same level as BWR hydrogen water chemistry surveillance. The future potential of corrosion potential monitoring will be discussed. Electrochemical measurements are also performed in other reactor systems and in other types of reactors. Experiences will be briefly reviewed. In a BWR on hydrogen water chemistry and in the PWR secondary system the corrosion potentials show a large variation between different system parts. To postulate the material behavior at different locations the local chemical and electrochemical conditions must be known. Thus, modeling of chemical and electrochemical conditions along

Monitoring reinforcement corrosion and corrosion-induced cracking using non-destructive x-ray attenuation measurements

DEFF Research Database (Denmark)

Michel, Alexander; Pease, Bradley Justin; Geiker, Mette Rica

2011-01-01

To test the applicability of the x-ray attenuation method to monitor the movement of corrosion products as well as the formation and propagation of cracks in cementitious materials reinforced mortar samples were prepared and tested under accelerated corrosion conditions. It is evident from the ex...... of the corrosion products averaged through the specimen thickness. The total mass loss of steel, obtained by the x-ray attenuation method, was found to be in very good agreement with the mass loss obtained by gravimetric method as well as Faraday's law....

The multimedia corrosion guide, 2. edition

International Nuclear Information System (INIS)

Audisio, S.

2006-01-01

Collecting the knowledge and experience of 26 international experts, the Multimedia Corrosion Guide is a reference book in the field of corrosion, for scientists, engineers, technicians and students. Also available in English, the second edition is more than just an update; it contains new chapters, new corrosion case studies and new smart functions. When knowledge is combined with experience, the result is a work of unprecedented quality and detail. Under the supervision of Professor Dr. S. Audisio of the Industrial Physical Chemistry Laboratory, INSA de Lyon, France, leading corrosion specialists from industry (Aerospatiale, CEA, EDF, ELF, Fragema, GDF, Pechiney, Renault, Rhone-Poulenc, Ugine...) have joined forces with experts from renowned French universities (INSA, UTC, ENSEEP, ENSCP, ENSAM...) to produce this book. In addition to the Corrosion Treatise, this program also contains a Case Studies Library, a corrosion database to which users can add their own experience base. New cases are automatically inserted alongside the existing ones, with the same selection criteria. Numerous other advanced functions make this second edition a unique, intelligent, professional and invaluable reference tool. (authors)

Influence of anaerobic physical effort in the horizontal and vertical peripheral view INFLUENCIA DEL ESFUERZO FÍSICO ANAERÓBICO EN LA VISIÓN PERIFÉRICA VERTICAL Y HORIZONTAL

Directory of Open Access Journals (Sweden)

M. Arteaga

2010-09-01

Full Text Available

There now seems to be a generalized tendency to consider that sporting performance declines as the sportsperson becomes fatigued. However, there is little empirical evidence to show that this adversely affects visual function. In some sports it is necessary to see stimuli in zones peripheral to central vision. The aim of this study is to analyze the influence of anaerobic exertion on vertical and horizontal Peripheral Vision. An intra-subject design was used with 14 replications. The visual parameters of Vertical Peripheral Vision and Horizontal Peripheral Vision were measured in different fatigue conditions to analyze the possible negative influence which this could exert on the subject’s visual capacity. The results show that fatigue due to anaerobic effort does not harm the visual abilities studied.
KEY WORDS: Peripheral Vision, Fatigue, Anaerobic exertion, Visual abilities

Parece haber una tendencia generalizada a considerar que el rendimiento deportivo disminuye en la medida en que los deportistas acumulan fatiga; sin embargo existen pocas evidencias empíricas que indiquen que la función visual se vea perjudicada por este motivo. En algunos deportes es necesario observar estímulos en zonas periféricas a la visión central. En el presente estudio se pretende analizar la influencia de los esfuerzos anaeeróbicos sobre la Visión Periférica (vertical y horizontal. Se utilizó un diseño intrasujeto A-(B1,B2-A con catorce replicaciones. Se realizaron mediciones de los parámetros visuales: Visión Periférica Vertical y Visión Periférica Horizontal en diferentes condiciones de fatiga para analizar la posible influencia negativa que pudiera ejercer ésta sobre la capacidad visual de los sujetos. Los resultados permiten afirmar que la fatiga debida a esfuerzos de tipo anaeróbico no producen un perjuicio sobre las habilidades visuales estudiadas.
PALABRAS CLAVE: Visi

High Temperature Corrosion in Biomass-Fired Boilers

DEFF Research Database (Denmark)

Henriksen, Niels; Montgomery, Melanie; Hede Larsen, Ole

2002-01-01

condense on superheater components. This gives rise to specific corrosion problems not previously encountered in coal-fired power plants. The type of corrosion attack can be directly ascribed to the composition of the deposit and the metal surface temperature. To avoid such high corrosion rates, woodchip...... has also been utilised as a fuel. Combustion of woodchip results in a smaller amount of ash, and potassium and chlorine are present in lesser amounts. However, significant corrosion rates were still seen. A case study of a woodchip fired boiler is described. The corrosion mechanisms in both straw-fired...... and woodchip fired boilers are discussed....

Launch Pad Coatings for Smart Corrosion Control

Science.gov (United States)

Calle, Luz M.; Hintze, Paul E.; Bucherl, Cori N.; Li, Wenyan; Buhrow, Jerry W.; Curran, Jerome P.; Whitten, Mary C.

2010-01-01

Corrosion is the degradation of a material as a result of its interaction with the environment. The environment at the KSC launch pads has been documented by ASM International (formerly American Society for Metals) as the most corrosive in the US. The 70 tons of highly corrosive hydrochloric acid that are generated by the solid rocket boosters during a launch exacerbate the corrosiveness of the environment at the pads. Numerous failures at the pads are caused by the pitting of stainless steels, rebar corrosion, and the degradation of concrete. Corrosion control of launch pad structures relies on the use of coatings selected from the qualified products list (QPL) of the NASA Standard 5008A for Protective Coating of Carbon Steel, Stainless Steel, and Aluminum on Launch Structures, Facilities, and Ground Support Equipment. This standard was developed to establish uniform engineering practices and methods and to ensure the inclusion of essential criteria in the coating of ground support equipment (GSE) and facilities used by or for NASA. This standard is applicable to GSE and facilities that support space vehicle or payload programs or projects and to critical facilities at all NASA locations worldwide. Environmental regulation changes have dramatically reduced the production, handling, use, and availability of conventional protective coatings for application to KSC launch structures and ground support equipment. Current attrition rate of qualified KSC coatings will drastically limit the number of commercial off the shelf (COTS) products available for the Constellation Program (CxP) ground operations (GO). CxP GO identified corrosion detection and control technologies as a critical, initial capability technology need for ground processing of Ares I and Ares V to meet Constellation Architecture Requirements Document (CARD) CxP 70000 operability requirements for reduced ground processing complexity, streamlined integrated testing, and operations phase affordability

Jenis dan Status Konservasi Ikan Hiu yang Tertangkap di Tempat Pelelangan Ikan (TPI Labuan Bajo, Manggarai Barat, Flores

Directory of Open Access Journals (Sweden)

Ismail Syakurachman Alaydrus

2016-03-01

Full Text Available The study aimed to determine the types of sharks are caught, sold and conservation status in the fish auction place (TPI Labuan Bajo, West Manggarai, Flores, East Nusa Tenggara have been conducted in February and March 2014 in Labuan Bajo. The research method was the survey method and used Market Survey sampling techniques and identification by Rapid Assessment method. Descriptively analyzed data, displayed in the form of narration and a table. Based on the results of the study, found 114 individual sharks, 55 individual males, 59 females were classified into three orders, namely Orectolobiformes, Lamniformes, and Carcharhiniformes; 4 families that Carcharhinidae, Odontaspididae, Rhynchobatidae, and Ginglymostomatidae; 5 genera namely Carcharhinus, Triaenodon, Rhyncobatus, Prionace, and Rhizoprionodon and 9 types of sharks that Carcharhinus melanopterus, Triaenodon obesus, Carcharhinus limbatus, Carcharhinus taurus, Carcharhinus amblyrhynchos, Rhynchobatus australiae, Prionace glauca, Rhizoprionodon acutus, and Nebrius ferrugineus. Based on the state of conservation, shark found in Labuan Bajo TPI classified Vulnerable and Near Threatened, the dominant type of shark found is Carcharhinus melanopterus (91 fishes while the least was found is Rhynchobatus australiae, Prionace glauca, Rhizoprionodon acutus, and Nebrius ferrugineus (each 1 individual.

Non-destructive elecrochemical monitoring of reinforcement corrosion

DEFF Research Database (Denmark)

Nygaard, Peter Vagn

been widely accepted as a non-destructive ”state of the art” technique for detection of corrosion in concrete structures. And, over the last decade, the trend in corrosion monitoring has moved towards quantitative non-destructive monitoring of the corrosion rate of the steel reinforcement. A few...... corrosion rate measurement instruments have been developed and are commercially available. The main features of these instruments are the combined use of an electrochemical technique for determining the corrosion rate and a so-called ”confinement technique”, which in principle controls the polarised surface...... area of the reinforcement, i.e. the measurement area. Both on-site investigations and laboratory studies have shown that varying corrosion rates are obtained when the various commercially available instruments are used. And in the published studies, conflicting explanations are given illustrating...

A New Corrosion Sensor to Determine the Start and Development of Embedded Rebar Corrosion Process at Coastal Concrete

OpenAIRE

Xu, Chen; Li, Zhiyuan; Jin, Weiliang

2013-01-01

The corrosion of reinforcements induced by chloride has resulted to be one of the most frequent causes of their premature damage. Most corrosion sensors were designed to monitor corrosion state in concrete, such as Anode-Ladder-System and Corrowatch System, which are widely used to monitor chloride ingress in marine concrete. However, the monitoring principle of these corrosion sensors is based on the macro-cell test method, so erroneous information may be obtained, especially from concrete u...

Effects of prior cold work on corrosion and corrosive wear of copper in HNO3 and NaCl solutions

International Nuclear Information System (INIS)

Yin Songbo; Li, D.Y.

2005-01-01

Effects of prior cold work on corrosion and corrosive wear behavior of copper in 0.1 M HNO 3 and 3.5% NaCl solutions, respectively, were investigated using electrochemical tests, electron work function measurements, and sliding corrosive wear tests with and without cathodic protection. Optical microscope and SEM were employed to examine the microstructure and worn surfaces. It was shown that, in general, the prior cold work raised the corrosion rate, but the effect differed in different corrosive media. In both the solutions, pure mechanical wear decreased with an increase in cold work. The prior cold work had a significant influence on the corrosive wear of copper, depending on the corrosive solution and the applied load. In the 0.1 M HNO 3 solution, the ratio of the wear loss caused by corrosion-wear synergism to the total wear loss increased with the cold work and became saturated when the cold work reached a certain level. In the 3.5% NaCl solution, however, this ratio decreased initially and then became relatively stable with respect to the cold work. It was observed that wear of copper in the 3.5% NaCl solution was larger than that in 0.1 M HNO 3 solution, although copper showed lower corrosion rate in the former solution. The experimental observations and the possible mechanisms involved are discussed

Flow accelerated corrosion and erosion-corrosion of RAFM steel in liquid breeders

International Nuclear Information System (INIS)

Kondo, Masatoshi; Muroga, Takeo; Sagara, Akio

2010-11-01

Corrosion experiments for RAFM, JLF-1 steel (Fe-9Cr-2w-0.1C) in 3types of flowing liquid breeders (i.e. Li, Pb-17Li and Flinak) were performed at the same conditions, and the compatibility was compared with each other. The weight loss of the specimens in the fluids was evaluated by the corrosion model based on mass transfer. The model can be applied to different test systems with different quantity of liquid breeders and different surface area of the systems. The flow enhanced the dissolution of element of the steel in the fluids. The mechanism of an erosion-corrosion in the liquid breeders was the peeling off of the corroded steel surface by the flow. (author)

Assessing Level and Effectiveness of Corrosion Education in the UAE

Directory of Open Access Journals (Sweden)

Hwee Ling Lim

2012-01-01

Full Text Available The consequences of corrosion can be minimized by an engineering workforce well trained in corrosion fundamentals and management. Since the United Arab Emirates incurs the second highest cost of corrosion after Saudi Arabia, this paper examined the quality of corrosion education in the UAE. Surveys with academia and industry respondents showed that dedicated corrosion courses and engineering courses that integrated corrosion into the curricula were available in UAE universities, but graduates had insufficient knowledge of corrosion engineering and superficial understanding of corrosion in real-life design contexts. The effectiveness of corrosion education is determined by both competence in corrosion knowledge/skills and availability of resources (faculty and research. Though most departments would not hire new corrosion-specialist faculty, department research efforts and industry partnerships in corrosion research were present. The paper concluded with recommendations for improving knowledge and skills of future engineers in corrosion and enhancing corrosion instruction to better meet industry needs.

Atmospheric corrosion of metals in industrial city environment

OpenAIRE

Kusmierek, Elzbieta; Chrzescijanska, Ewa

2015-01-01

Atmospheric corrosion is a significant problem given destruction of various materials, especially metals. The corrosion investigation in the industrial city environment was carried out during one year exposure. Corrosion potential was determined using the potentiometric method. The highest effect of corrosion processes was observed during the winter season due to increased air pollution. Corrosion of samples pre-treated in tannic acid before the exposure was more difficult compared with the s...

General corrosion, irradiation-corrosion, and environmental-mechanical evaluation of nuclear-waste-package structural-barrier materials. Progress report

International Nuclear Information System (INIS)

Westerman, R.E.; Pitman, S.G.; Nelson, J.L.

1982-09-01

Pacific Northwest Laboratory is studying the general corrosion, irradiation-corrosion, and environmentally enhanced crack propagation of five candidate materials in high-temperature aqueous environments simulating those expected in basalt and tuff repositories. The materials include three cast ferrous materials (ductile cast iron and two low-alloy Cr-Mo cast steels) and two titanium alloys, titanium Grade 2 (commercial purity) and Grade 12 (a Ti-Ni-Mo alloy). The general corrosion results are being obtained by autoclave exposure of specimens to slowly replenished simulated ground water flowing upward through a bed of the appropriate crushed rock (basalt or tuff), which is maintained at the desired test temperature (usually 250 0 C). In addition, tests are being performed in deionized water. Metal penetration rates of iron-base alloys are being derived by stripping off the corrosion product film and weighing the specimen after the appropriate exposure time. The corrosion of titanium alloy specimens is being determined by weight gain methods. The irradiation-corrosion studies are similar to the general corrosion tests, except that the specimen-bearing autoclaves are held in a 60 Co gamma radiation field at dose rates up to 2 x 10 6 rad/h. For evaluating the resistance of the candidate materials to environmentally enhanced crack propagation, three methods are being used: U-bend and fracture toughness specimens exposed in autoclaves; slow strain rate studies in repository-relevant environments to 300 0 C; and fatigue crack growth rate studies at ambient pressure and 90 0 C. The preliminary data suggest a 1-in. corrosion allowance for iron-base barrier elements intended for 1000-yr service in basalt or tuff repositories. No evidence has yet been found that titanium Grade 2 or Grade 12 is susceptible to environmentally induced crack propagation or, by extension, to stress corrosion cracking

On-line Corrosion Monitoring in District Heating Systems

DEFF Research Database (Denmark)

Richter, Sonja; Thorarinsdottir, R.I.; Hilbert, Lisbeth Rischel

2005-01-01

The corrosion control in district heating systems is today performed primarily with control of the water quality. The corrosion rate is kept low by assuring low dissolved oxygen concentration, high pH and low conductivity. Corrosion failures can occur, e.g. as a result of unknown oxygen ingress, ......, precipitation of deposits or crevices. The authors describe methods used for on-line monitoring of corrosion, cover the complications and the main results of a Nordic project.......The corrosion control in district heating systems is today performed primarily with control of the water quality. The corrosion rate is kept low by assuring low dissolved oxygen concentration, high pH and low conductivity. Corrosion failures can occur, e.g. as a result of unknown oxygen ingress...

Ventilación mecánica convencional en recién nacidos muy bajo peso ingresados en el hospital provincial Dr. Ernesto Guevara de la Serna

OpenAIRE

Lenny Carbonell García; Alicia Fernández Chacón; Yadira Rodríguez Ramírez; Maribel Machado

2015-01-01

Se realizó un estudio descriptivo de corte transversal, para determinar el comportamiento de los recién nacidos muy bajo peso, ventilados en modalidades convencionales en el Hospital General Docente “Dr. Ernesto Guevara de la Serna”, en el período de enero de 2010 a julio de 2012. El universo estuvo constituido por 104 recién nacidos vivos muy bajo peso, tomándose como muestra a los 66 recién nacidos muy bajo peso que necesitaron apoyo ventilatorio. Las principales variables a estudiar fueron...

Corrosion problems in PWR steam generators

International Nuclear Information System (INIS)

Weber, J.; Suery, P.

1976-01-01

Examinations on pulled steam generator tubes from the Swiss nuclear power plants Beznau I and II, together with some laboratory tests, may be summarized as follows: Corrosion problems in vertical U-tube steam generators with Alloy 600 as tube material are localized towards relatively narrow regions above the tube sheet where thermohydraulic conditions and, as a consequence thereof, chemical conditions are uncontrolled. Within these zones Alloy 600 is not sufficienthy resistent to caustic or phosphate attack (caustic stress corrosion cracking and general corrosion, resp.). The mechanisms of several corrosion phenomena are not fully understood. (orig.) [de

Exfoliation Corrosion and Pitting Corrosion and Their Role in Fatigue Predictive Modeling: State-of-the-Art Review

Directory of Open Access Journals (Sweden)

David W. Hoeppner

2012-01-01

Full Text Available Intergranular attack (IG and exfoliation corrosion (EC have a detrimental impact on the structural integrity of aircraft structures of all types. Understanding the mechanisms and methods for dealing with these processes and with corrosion in general has been and is critical to the safety of critical components of aircraft. Discussion of cases where IG attack and exfoliation caused issues in structural integrity in aircraft in operational fleets is presented herein along with a much more detailed presentation of the issues involved in dealing with corrosion of aircraft. Issues of corrosion and fatigue related to the structural integrity of aging aircraft are introduced herein. Mechanisms of pitting nucleation are discussed which include adsorption-induced, ion migration-penetration, and chemicomechanical film breakdown theories. In addition, pitting corrosion (PC fatigue models are presented as well as a critical assessment of their application to aircraft structures and materials. Finally environmental effects on short crack behavior of materials are discussed, and a compilation of definitions related to corrosion and fatigue are presented.

Estrés Materno y Configuración Familiar: Estudio comparativo en Familias Chilenas Monoparentales y Nucleares de bajos ingresos

OpenAIRE

Olhaberry, Marcia; Pontificia Universidad Católica de Chile; Farkas, Chamarrita

2012-01-01

Los estudios sobre estrés materno durante la crianza infantil han considerado variables contextuales para explicarlo. El nivel socioeconómico, así como la configuración familiar han sido variables relevantes, asociándose monoparentalidad en familias de bajos ingresos a mayores niveles de estrés materno. Se estudian los niveles de estrés materno en familias chilenas nucleares y monoparentales de N.S.E. bajo, considerando el estrés en distintas dimensiones, asociado al rol materno, a la interac...

Astrakhan-Mangyshlak water main (pipeline): corrosion state of the inner surface, and methods for its corrosion protection. Part III. The effects of KW2353 inhibitor. Part IV. Microbiological corrosion

International Nuclear Information System (INIS)

Reformatskaya, I.I.; Ashcheulova, I.I.; Barinova, M.A.; Kostin, D.V.; Prutchenko, S.G.; Ivleva, G.A.; Taubaldiev, T.S.; Murinov, K.S.; Tastanov, K.Kh.

2003-01-01

The effect of the KW2353 corrosion inhibitor, applied on the Astrakhan-Mangyshlak water main (pipeline) since 1997, on the corrosion processes, occurring on the 17G1S steel surface, is considered. The properties of the surface sediments are also considered. The role of the microbiological processes in the corrosion behavior of the water main (pipeline) inner surface is studied. It is shown, that application of the polyphosphate-type inhibitors, including the KW2353 one, for the anticorrosive protection of the inner surface of the extended water main (pipelines) is inadmissible: at the temperature of ∼20 deg C this corrosion inhibitor facilitates the development of the local corrosion processes on the water main (pipeline) inner surface. At the temperature of ∼8 deg C the above inhibitor discontinues to effect the corrosive stability of the 17G1S steel. The optimal way of the anticorrosive protection of the steel equipment, contacting with the water media, is the increase in the oxygen content therein [ru

High temperature corrosion in straw-fired power plants: Influence of steam/metal temperature on corrosion rates for TP347H

DEFF Research Database (Denmark)

Montgomery, Melanie; Biede, O; Larsen, OH

2002-01-01

The corrosion in straw-fired boilers has been investigated at various straw-fired power plants in Denmark. Water/air-cooled probes, a test superheater and test sections removed from the actual superheater have been utilised to characterise corrosion and corrosion rates. This paper describes...... the corrosion rates measured for the TP347H type steel. The corrosion morphology at high temperature consists of grain boundary attack and selective attack of chromium. The corrosion rate increases with calculated metal temperature (based on steam temperature), however there is great variation within....... The difference in the results could be traced back to a lower flue gas temperature on one side of the boiler. Although metal temperature is the most important parameter with respect to corrosion rate, flue gas temperature also plays an important role. Efforts to quantify the effect of flue gas temperature...

Radiation-induced corrosion of stellite-6

International Nuclear Information System (INIS)

Behazin, M.; Wren, J.C.

2012-09-01

Stellite-6 is a Co-based (58%) alloy that is used for components that require high wear-resistance, such as valve facings and ball bearings in nuclear reactors. In the reactor core, stable 59 Co can be neutron activated by absorption of a neutron to become the radioactive isotope, 60 Co. The 60 Co that is created constitutes a safety hazard for plant workers who have to perform maintenance on the reactor. One of the operational and safety issues in a nuclear reactor is the potential corrosion of Co-based alloys and the introduction of dissolved Co ions into the reactor core. While the corrosion of Stellite-6 has been studied its corrosion behaviour with ionizing radiation present has not been well established. Corrosion kinetics depend on both the aqueous redox conditions and the physical and chemical nature of the alloy surface. The high radiation fields present in a reactor core will cause water to decompose to a range of redox-active species (both highly oxidizing (e.g., ·OH, H 2 O 2 ) and highly reducing (e.g., ·eaq - , ·O 2 - )). These species can significantly influence corrosion kinetics. The effect of γ-radiation on the corrosion of Stellite-6 at pH 10.6 was investigated at temperatures ≤ 150 deg. C. Since the corrosion rate depends strongly on the type of oxide that is present on the material surface, the focus of this corrosion study was to establish the mechanism by which radiolysis affects the nature of the oxide that is present on Stellite-6. The results show that γ-radiation (at a dose rate of 5.5 kGy.h -1 ) increases the corrosion potential on Stellite-6 from -0.7 VSCE to 0.12 VSCE . The corrosion potential without irradiation present is in a potential range where oxidation is limited to the formation of a Co (OH) 2 and CoCr 2 O 4 outer oxide layer on a pre-existing Cr 2 O 3 film. The corrosion potential with irradiation is in a potential range where further oxidation of Co (OH) 2 to CoOOH also occurs. However, since CoOOH is less soluble than

Water side corrosion prevention in boilers

International Nuclear Information System (INIS)

Zeid, A.

1993-01-01

Corrosion may be defined as a naturally occurring physical and chemical deterioration of a material due to reaction with the environment or surrounding atmosphere. In boilers the material is subjected on both sides to two different media which may cause severe corrosion. At the water side the content of O 2 considered one of the principal factors which determine the extent of corrosion in the boiler tubes. This paper deals with certain conditions that result in the increase of O 2 in the boiler water and hence increase the corrosion rate, to minimize the effect of these conditions a chemical treatment was carried out the results obtained indicated the success of the treatment procedure in corrosion prevention and boiler material protection. The treatment is traditional. But the study indicates how a simple mean could be applied to solve a serious problem. 4 tab

Vehicle accelerated corrosion test procedures for automotive in Malaysia

Directory of Open Access Journals (Sweden)

Anuar Liza

2017-01-01

Full Text Available An accelerated corrosion test, known as proving ground accelerated test, is commonly performed by automotive manufacturers to evaluate the corrosion performance of a vehicle. The test combines corrosion and durability inputs to detect potential failures that may occur during in-service conditions. Currently, the test is conducted at an external test center overseas. Such test is aimed to simulate the effects of one year accelerated corrosion in severe corrosive environment of the north-east and south east of America. However, the test results obtained do not correlate with the actual corrosion conditions observed in the Malaysian market, which is likely attributed to the different test environment of the tropical climate of vehicles in service. Therefore, a vehicle accelerated corrosion test procedure that suits the Malaysian market is proposed and benchmarked with other global car manufacturers that have their own dedicated corrosion test procedure. In the present work, a test track is used as the corrosion test ground and consists of various types of roads for structural durability exposures. Corrosion related facilities like salt trough, mud trough and gravel road are constructed as addition to the existing facilities. The establishment of accelerated corrosion test facilities has contributed to the development of initial accelerated corrosion test procedure for the national car manufacturer. The corrosion exposure is monitored by fitting test coupons at the underbody of test vehicle using mass loss technique so that the desired corrosion rate capable of simulating the real time corrosion effects for its target market.

Corrosion resistant cemented carbide

International Nuclear Information System (INIS)

Hong, J.

1990-01-01

This paper describes a corrosion resistant cemented carbide composite. It comprises: a granular tungsten carbide phase, a semi-continuous solid solution carbide phase extending closely adjacent at least a portion of the grains of tungsten carbide for enhancing corrosion resistance, and a substantially continuous metal binder phase. The cemented carbide composite consisting essentially of an effective amount of an anti-corrosion additive, from about 4 to about 16 percent by weight metal binder phase, and with the remaining portion being from about 84 to about 96 percent by weight metal carbide wherein the metal carbide consists essentially of from about 4 to about 30 percent by weight of a transition metal carbide or mixtures thereof selected from Group IVB and of the Periodic Table of Elements and from about 70 to about 96 percent tungsten carbide. The metal binder phase consists essentially of nickel and from about 10 to about 25 percent by weight chromium, the effective amount of an anti-corrosion additive being selected from the group consisting essentially of copper, silver, tine and combinations thereof

Corrosion in seawater systems

International Nuclear Information System (INIS)

Henrikson, S.

1988-01-01

Highly alloyed stainless steels have been exposed to natural chlorinated and chlorine-free seawater at 35 deg. C. Simulated tube-tubesheet joints, weld joints and galvanic couples with titanium, 90/10 CuNi and NiAl bronze were tested and evaluated for corrosion. The corrosion rates of various anode materials - zinc, aluminium and soft iron - were also determined. Finally the risk of hydrogen embrittlement of tubes of ferritic stainless steels and titanium as a consequence of cathodic protection was studied. An attempt was also made to explain the cracking mechanism of the ferritic steels by means of transmission electron microscopy. One important conclusion of the project is that chlorinated seawater is considerably more corrosive to stainless steels than chlorine-free water, whereas chlorination reduces the rate of galvanic corrosion of copper materials coupled to stainless steels. Hydrogen embrittlement of ferritic stainless steels and titanium as a consequence of cathodic protection of carbon steel or cast iron in the same structure can be avoided by strict potentiostatic control of the applied potential. (author)

Corrosion behavior of 2205 duplex stainless steel.

Science.gov (United States)

Platt, J A; Guzman, A; Zuccari, A; Thornburg, D W; Rhodes, B F; Oshida, Y; Moore, B K

1997-07-01

The corrosion of 2205 duplex stainless steel was compared with that of AISI type 316L stainless steel. The 2205 stainless steel is a potential orthodontic bracket material with low nickel content (4 to 6 wt%), whereas the 316L stainless steel (nickel content: 10 to 14 wt%) is a currently used bracket material. Both stainless steels were subjected to electrochemical and immersion (crevice) corrosion tests in 37 degrees C, 0.9 wt% sodium chloride solution. Electrochemical testing indicates that 2205 has a longer passivation range than 316L. The corrosion rate of 2205 was 0.416 MPY (milli-inch per year), whereas 316L exhibited 0.647 MPY. When 2205 was coupled to 316L with equal surface area ratio, the corrosion rate of 2205 reduced to 0.260 MPY, indicating that 316L stainless steel behaved like a sacrificial anode. When 316L is coupled with NiTi, TMA, or stainless steel arch wire and was subjected to the immersion corrosion test, it was found that 316L suffered from crevice corrosion. On the other hand, 2205 stainless steel did not show any localized crevice corrosion, although the surface of 2205 was covered with corrosion products, formed when coupled to NiTi and stainless steel wires. This study indicates that considering corrosion resistance, 2205 duplex stainless steel is an improved alternative to 316L for orthodontic bracket fabrication when used in conjunction with titanium, its alloys, or stainless steel arch wires.

Plastics for corrosion inhibition

CERN Document Server

Goldade, Victor A; Makarevich, Anna V; Kestelman, Vladimir N

2005-01-01

The development of polymer composites containing inhibitors of metal corrosion is an important endeavour in modern materials science and technology. Corrosion inhibitors can be located in a polymer matrix in the solid, liquid or gaseous phase. This book details the thermodynamic principles for selecting these components, their compatibility and their effectiveness. The various mechanisms of metal protection – barrier, inhibiting and electromechanical – are considered, as are the conflicting requirements placed on the structure of the combined material. Two main classes of inhibited materials (structural and films/coatings) are described in detail. Examples are given of structural plastics used in friction units subjected to mechano-chemical wear and of polymer films/coatings for protecting metal objects against corrosion.

Microencapsulation Technologies for Corrosion Protective Coating Applications

Science.gov (United States)

Li, Wenyan; Buhrow, Jerry; Jolley, Scott; Calle, Luz; Pearman, Benjamin; Zhang, Xuejun

2015-01-01

Microencapsulation technologies for functional smart Coatings for autonomous corrosion control have been a research area of strong emphasis during the last decade. This work concerns the development of pH sensitive micro-containers (microparticles and microcapsules) for autonomous corrosion control. This paper presents an overview of the state-of-the-art in the field of microencapsulation for corrosion control applications, as well as the technical details of the pH sensitive microcontainer approach, such as selection criteria for corrosion indicators and corrosion inhibitors; the development and optimization of encapsulation methods; function evaluation before and after incorporation of the microcontainers into coatings; and further optimization to improve coating compatibility and performance.

Ferritic stainless steels: corrosion resistance + economy

International Nuclear Information System (INIS)

Remus, A.L.

1976-01-01

Ferritic stainless steels provide corrosion resistance at lower cost. They include Type 409, Type 439, 18SR, 20-Mo (1.6 Mo), 18-2 (2 Mo), 26-1S, E-Brite 26-1, 29 Cr-4 Mo, and 29 Cr-4 Mo-2 Ni. Their corrosion and mechanical properties are examined. Resistance to stress-corrosion cracking is an advantage compared to austenitic types

bajo el bosque en Costa Rica. 1980-2000

Directory of Open Access Journals (Sweden)

Rafael Ocampo

2007-01-01

Full Text Available La ipecacuana o raicilla, hierba nativa de América, es la única planta medicinal del trópico húmedo de Costa Rica cultivada bajo el bosque. Es cultivada en la región Huetar Norte, limítrofe con Nicaragua; la raíz seca de ipecacuana se ha comercializado en Costa Rica como materia prima para la industria farmacéutica internacional desde principios del siglo XX. De acuerdo con las estadísticas oficiales, las exportaciones de raicilla desde Costa Rica en los últimos 20 años han significado un promedio de 64 t año-1. Este trabajo resume actividades relacionadas con la descripción y cultivo de la planta, así como algunos de los aspectos agroecológicos de su cultivo.

Recent Natural Corrosion Inhibitors for Mild Steel: An Overview

Directory of Open Access Journals (Sweden)

Marko Chigondo

2016-01-01

Full Text Available Traditionally, reduction of corrosion has been managed by various methods including cathodic protection, process control, reduction of the metal impurity content, and application of surface treatment techniques, as well as incorporation of suitable alloys. However, the use of corrosion inhibitors has proven to be the easiest and cheapest method for corrosion protection and prevention in acidic media. These inhibitors slow down the corrosion rate and thus prevent monetary losses due to metallic corrosion on industrial vessels, equipment, or surfaces. Inorganic and organic inhibitors are toxic and costly and thus recent focus has been turned to develop environmentally benign methods for corrosion retardation. Many researchers have recently focused on corrosion prevention methods using green inhibitors for mild steel in acidic solutions to mimic industrial processes. This paper provides an overview of types of corrosion, corrosion process, and mainly recent work done on the application of natural plant extracts as corrosion inhibitors for mild steel.

Corrosion problems and solutions in oil refining and petrochemical industry

CERN Document Server

Groysman, Alec

2017-01-01

This book addresses corrosion problems and their solutions at facilities in the oil refining and petrochemical industry, including cooling water and boiler feed water units. Further, it describes and analyzes corrosion control actions, corrosion monitoring, and corrosion management. Corrosion problems are a perennial issue in the oil refining and petrochemical industry, as they lead to a deterioration of the functional properties of metallic equipment and harm the environment – both of which need to be protected for the sake of current and future generations. Accordingly, this book examines and analyzes typical and atypical corrosion failure cases and their prevention at refineries and petrochemical facilities, including problems with: pipelines, tanks, furnaces, distillation columns, absorbers, heat exchangers, and pumps. In addition, it describes naphthenic acid corrosion, stress corrosion cracking, hydrogen damages, sulfidic corrosion, microbiologically induced corrosion, erosion-corrosion, and corrosion...

On-line corrosion monitoring in district heating systems

DEFF Research Database (Denmark)

Richter, Sonja; Thorarinsdottir, R.I.; Hilbert, Lisbeth Rischel

2004-01-01

), Electrochemical Noise (EN) and Zero Resistance Ammetry (ZRA). Electrochemical Resistance (ER) has also been used to measure corrosion. The method traditionally only measures corrosion off-line but with newly developed high-sensitive ER technique developed by MetriCorr in Denmark, on-line monitoring is possible...... complicates the chemistry of the environment. Hydrogen sulphide is present in geothermal systems and can be formed as a by-product of sulphate-reducing-bacteria (SRB). The application of electrochemical methods makes on-line monitoring possible. These methods include: Linear Polarization Resistance (LPR....... In order to assess both general corrosion and localized corrosion, it is necessary to apply more than one monitoring technique simultaneously, ZRA or EN for measuring localized corrosion and LPR or ER for measuring general corrosion rate. The advantage of monitoring localized corrosion is indisputable...

49 CFR 192.475 - Internal corrosion control: General.

Science.gov (United States)

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Internal corrosion control: General. 192.475... Control § 192.475 Internal corrosion control: General. (a) Corrosive gas may not be transported by... taken to minimize internal corrosion. (b) Whenever any pipe is removed from a pipeline for any reason...

Microbiologically Influenced Corrosion: Causative Organisms and Mechanisms

Science.gov (United States)

2012-01-31

enviromental composition as a potential method for reversing microbiologically influenced corrosion, Corrosion (NAC’E) International. Houston. Texas...International fellow and associate editor for Biofouling, The Journal of Bioadhesion and Biofilm Research. J. Lee is a Materials and Corrosion Engineer

[Epiphytic algae from Bajo Pepito, Isla Mujeres, Quintana Roo, Mexico].