WorldWideScience

Sample records for core restraint mechanism

  1. Core mechanics and configuration behavior of advanced LMFBR core restraint concepts

    International Nuclear Information System (INIS)

    Fox, J.N.; Wei, B.C.

    1978-02-01

    Core restraint systems in LMFBRs maintain control of core mechanics and configuration behavior. Core restraint design is complex due to the close spacing between adjacent components, flux and temperature gradients, and irradiation-induced material property effects. Since the core assemblies interact with each other and transmit loads directly to the core restraint structural members, the core assemblies themselves are an integral part of the core restraint system. This paper presents an assessment of several advanced core restraint system and core assembly concepts relative to the expected performance of currently accepted designs. A recommended order for the development of the advanced concepts is also presented

  2. Mechanical restraint in psychiatry

    DEFF Research Database (Denmark)

    Bak, Jesper; Zoffmann, Vibeke; Sestoft, Dorte Maria

    2014-01-01

    PURPOSE: To examine how potential mechanical restraint preventive factors in hospitals are associated with the frequency of mechanical restraint episodes. DESIGN AND METHODS: This study employed a retrospective association design, and linear regression was used to assess the associations. FINDINGS......: Three mechanical restraint preventive factors were significantly associated with low rates of mechanical restraint use: mandatory review (exp[B] = .36, p mechanical...

  3. Bypass Flow and Hot Spot Analysis for PMR200 Block-Core Design with Core Restraint Mechanism

    International Nuclear Information System (INIS)

    Lim, Hong Sik; Kim, Min Hwan

    2009-01-01

    The accurate prediction of local hot spot during normal operation is important to ensure core thermal margin in a very high temperature gas-cooled reactor because of production of its high temperature output. The active cooling of the reactor core determining local hot spot is strongly affected by core bypass flows through the inter-column gaps between graphite blocks and the cross gaps between two stacked fuel blocks. The bypass gap sizes vary during core life cycle by the thermal expansion at the elevated temperature and the shrinkage/swelling by fast neutron irradiation. This study is to investigate the impacts of the variation of bypass gaps during core life cycle as well as core restraint mechanism on the amount of bypass flow and thus maximum fuel temperature. The core thermo fluid analysis is performed using the GAMMA+ code for the PMR200 block-core design. For the analysis not only are some modeling features, developed for solid conduction and bypass flow, are implemented into the GAMMA+ code but also non-uniform bypass gap distribution taken from a tool calculating the thermal expansion and the shrinkage/swell of graphite during core life cycle under the design options with and without core restraint mechanism is used

  4. Lateral restraint assembly for reactor core

    Science.gov (United States)

    Gorholt, Wilhelm; Luci, Raymond K.

    1986-01-01

    A restraint assembly for use in restraining lateral movement of a reactor core relative to a reactor vessel wherein a plurality of restraint assemblies are interposed between the reactor core and the reactor vessel in circumferentially spaced relation about the core. Each lateral restraint assembly includes a face plate urged against the outer periphery of the core by a plurality of compression springs which enable radial preloading of outer reflector blocks about the core and resist low-level lateral motion of the core. A fixed radial key member cooperates with each face plate in a manner enabling vertical movement of the face plate relative to the key member but restraining movement of the face plate transverse to the key member in a plane transverse to the center axis of the core. In this manner, the key members which have their axes transverse to or subtending acute angles with the direction of a high energy force tending to move the core laterally relative to the reactor vessel restrain such lateral movement.

  5. Magnetic nuclear core restraint and control

    International Nuclear Information System (INIS)

    Cooper, M.H.

    1979-01-01

    A lateral restraint and control system for a nuclear reactor core adaptable to provide an inherent decrease of core reactivity in response to abnormally high reactor coolant fluid temperatures. An electromagnet is associated with structure for radially compressing the core during normal reactor conditions. A portion of the structures forming a magnetic circuit are composed of ferromagnetic material having a curie temperature corresponding to a selected coolant fluid temperature. Upon a selected signal, or inherently upon a preselected rise in coolant temperature, the magnetic force is decreased a given amount sufficient to relieve the compression force so as to allow core radial expansion. The expanded core configuration provides a decreased reactivity, tending to shut down the nuclear reaction

  6. Magnetic nuclear core restraint and control

    International Nuclear Information System (INIS)

    Cooper, M.H.

    1979-01-01

    A lateral restraint and control systemm for a nuclear reactor core provides an inherent decrease of core reactivity in response to abnormally high reactor coolant fluid temperatures. An electromagnet is associated with structure for radially compressing the core during normal reactor conditions. A portion of the structures forming a magnetic circuit is composed of ferromagnetic material having a curie temperature corresponding to a selected coolant fluid temperature. Upon a selected signal, or inherently upon a preselected rise in coolant temperature, the magnetic force is decreased by an amount sufficient to relieve the compression force so as to allow core radial expansion. The expanded core configuration provides a decreased reactivity, tending to shut down the nuclear reaction

  7. Magnetic nuclear core restraint and control

    International Nuclear Information System (INIS)

    Cooper, M.H.

    1978-01-01

    Disclosed is a lateral restraint and control system for a nuclear reactor core adaptable to provide an inherent decrease of core reactivity in response to abnormally high reactor coolant fluid temperatures. An electromagnet is associated with structure for radially compressing the core during normal reactor conditions. A portion of the structures forming a magnetic circuit are composed of ferromagnetic material having a curie temperature corresponding to a selected coolant fluid temperature. Upon a selected signal, or inherently upon a preselected rise in coolant temperature, the magnetic force is decreased a given amount sufficient to relieve the compression force so as to allow core radial expansion. The expanded core configuration provides a decreased reactivity, tending to shut down the nuclear reaction

  8. Stress analysis of two-dimensional C/C composite components for HTGR's core restraint techanism

    International Nuclear Information System (INIS)

    Satoshi Hanawa; Taiju Shibata; Jyunya Sumita; Masahiro Ishihara; Tatsuo Iyoku; Kazuhiro Sawa

    2005-01-01

    Carbon fiber reinforced carbon matrix composite (C/C composite) is one of the most promising materials for HTGRs core components due to their high strength as well as high temperature resistibility. One of the most attractive applications of C/C composite is the core restraint mechanism. The core restraint mechanism is located around the reflector block and it works to tighten reactor core blocks so as to restrict un-supposition flow pass of coolant gas (bypass flow) in the core. The restriction of bypass flow reads to the high efficiency of coolant flow rate inside of the reactor core. For the future HTGRs and VHTR (Very High Temperature Reactor), it is important to develop the core restraint mechanism with C/C composite substitute for metallic materials as used for HTTR. For the application of C/C composite to core restraint mechanism, it is important to investigate the applicability of C/C composite in viewpoint of structural integrity. In the present study, supposing the application of 2D-C/C composite to core restraint mechanism, thermal stress behavior was analyzed by considering the thickness of the C/C composite and the gap between reflector block and core restraint. It was shown from the thermal stress analysis that the circumferential stress decreases with increasing the gap and that the restraint force increases with increasing the thickness. By optimizing the thickness of C/C composite and gap between reflector block and core restraint, the C/C composite is applicable to the core restraint mechanism. (authors)

  9. Mechanical Restraint - Which Interventions Prevent Episodes of Mechanical Restraint? - A Systematic Review

    DEFF Research Database (Denmark)

    Bak, Jesper; Brandt-Christensen, Anne Mette; Sestoft, Dorte Maria

    2012-01-01

    PURPOSE:  To identify interventions preventing mechanical restraints. DESIGN AND METHODS:  Systematic review of international research papers dealing with mechanical restraint. The review combines qualitative and quantitative research in a new way, describing the quality of evidence and the effect...... of intervention. FINDINGS:  Implementation of cognitive milieu therapy, combined interventions, and patient-centered care were the three interventions most likely to reduce the number of mechanical restraints. PRACTICE IMPLICATIONS:  There is a lack of high-quality and effective intervention studies. This leaves...... patients and metal health professionals with uncertainty when choosing interventions in an attempt to prevent mechanical restraints....

  10. Overview of the design of core restraint systems

    International Nuclear Information System (INIS)

    Heinecke, J.

    1984-01-01

    The optimization of the core restraint system is an important condition for the safe and reliable operation of a fast breeder reactor. For KNK II which is under successful operation and SNR 300 all requirements for safety and operation have been met with help of a ring type system. For SNR 2 the decision between the ring type system and the free standing core has to be done in the near future. Within these considerations the advantages of a ring type restraint system of limiting deflections during operation and limiting of possible movements under seismic conditions have to be balanced against the somewhat more complicated structure of the ring type restraint system

  11. Overview of core designs and requirements/criteria for core restraint systems

    International Nuclear Information System (INIS)

    Sutherland, W.H.

    1984-09-01

    The requirements and lifetime criteria for the design of a Liquid Metal Fast Breeder Reactor (LMFBR) Core Restraint System are presented. A discussion of the three types of core restraint systems used in LMFBR core design is given. Details of the core restraint system selected for FFTF are presented and the reasons for this selection given. Structural analysis procedures being used to manage the FFTF assembly irradiations are discussed. Efforts that are ongoing to validate the calculational methods and lifetime criteria are presented

  12. Fast Flux Test Facility core restraint system performance

    International Nuclear Information System (INIS)

    Hecht, S.L.; Trenchard, R.G.

    1990-02-01

    Characterizing Fast Flux Test Facility (FFTF) core restraint system performance has been ongoing since the first operating cycle. Characterization consists of prerun analysis for each core load, in-reactor and postirradiation measurements of subassembly withdrawal loads and deformations, and using measurement data to fine tune predictive models. Monitoring FFTF operations and performing trend analysis has made it possible to gain insight into core restraint system performance and head off refueling difficulties while maximizing component lifetimes. Additionally, valuable information for improved designs and operating methods has been obtained. Focus is on past operating experience, emphasizing performance improvements and avoidance of potential problems. 4 refs., 12 figs., 2 tabs

  13. Supporting system for the core restraint of nuclear reactors

    International Nuclear Information System (INIS)

    Kaser, A.

    1973-01-01

    The core restraint of water cooled nuclear reactors which is needed to direct the flow of the coolant through the core can be manufactured only in a moderate wall thickness. Thus, the majority of the loads have to be transmitted to the core barrel which is more rigid. The patent refers to a system of circumferential and vertical support members most of which are free to move relatively to each other, thus reducing thermal stresses during operation. (P.K.)

  14. 'Mechanical restraint-confounders, risk, alliance score'

    DEFF Research Database (Denmark)

    Deichmann Nielsen, Lea; Bech, Per; Hounsgaard, Lise

    2017-01-01

    . AIM: To clinically validate a new, structured short-term risk assessment instrument called the Mechanical Restraint-Confounders, Risk, Alliance Score (MR-CRAS), with the intended purpose of supporting the clinicians' observation and assessment of the patient's readiness to be released from mechanical...... restraint. METHODS: The content and layout of MR-CRAS and its user manual were evaluated using face validation by forensic mental health clinicians, content validation by an expert panel, and pilot testing within two, closed forensic mental health inpatient units. RESULTS: The three sub-scales (Confounders......, Risk, and a parameter of Alliance) showed excellent content validity. The clinical validations also showed that MR-CRAS was perceived and experienced as a comprehensible, relevant, comprehensive, and useable risk assessment instrument. CONCLUSIONS: MR-CRAS contains 18 clinically valid items...

  15. Overview of core designs and requirements/criteria for core restraint systems

    International Nuclear Information System (INIS)

    Sutherland, W.H.

    1984-01-01

    The requirements and lifetime criteria for the design of a Liquid Metal Fast Breeder Reactor (LMFBR) Core Restraint System is presented. A discussion of the three types of core restraint systems used in LMFBR core design is given. Details of the core restraint system selected for FFTF are presented and the reasons for this selection given. Structural analysis procedures being used to manage the FFTF assembly irradiations are discussed. Efforts that are ongoing to validate the calculational methods and lifetime criteria are presented. (author)

  16. Prediction of PEC core mechanical behaviour

    International Nuclear Information System (INIS)

    Cecchini, F.; Di Francesca, R.; Mcloughlin, J.; Neri, P.

    1984-01-01

    A brief description of the original PEC core restraint system is presented. Recent advanced seismic analysis studies have necessitated the introduction of anti-seismic design modifications which have increased the difficulties of fuel handling. Computer codes and numerical methods, used by ENEA to resolve core restraint and fuel handling problems are given together with an outline of mechanical tests and handling experiments in support of the anti-seismic core design. (author)

  17. Restraint system for core elements of a reactor core

    International Nuclear Information System (INIS)

    Class, G.

    1975-01-01

    In a nuclear reactor, a core element bundle formed of a plurality of side-by-side arranged core elements is surrounded by restraining elements that exert a radially inwardly directly restraining force generating friction forces between the core elements in a restraining plane that is transverse to the core element axes. The adjoining core elements are in rolling contact with one another in the restraining plane by virtue of rolling-type bearing elements supported in the core elements. (Official Gazette)

  18. Design of the core support and restraint structures for FFTF and CRBRP

    International Nuclear Information System (INIS)

    Sutton, H.G.; Rylatt, J.A.

    1977-12-01

    This paper presents and compares the design and fabrication of the FFTF and CRBRP reactor structures which support and restrain the reactor core assemblies. The fabrication of the core support structure (CSS) for the FFTF reactor was completed October 1972 and this paper discusses how the fabrication problems encountered with the FFTF were avoided in the subsequent design of the CRBR CSS. The radial core restraint structure of the FFTF was designed and fabricated such that an active system could replace the present passive system which is segmented and relies on the CSS core barrel for total structure integrity to maintain core geometry. The CRBR core restraint structure is designed for passive restraint only, and this paper discusses how the combined strengths of the restraint structure former rings and the CSS core barrel are utilized to maintain core geometry. Whereas the CSS for the FFTF interfaces directly with the reactor core assemblies, the CRBR CSS does not. A comparison is made on how intermediate structures in CRBR (inlet modules) provide the necessary design interfaces for supporting and providing flow distribution to the reactor core assemblies. A discussion is given on how the CRBR CSS satisfied the design requirements of the Equipment Specification, including thermal transient, dynamic and seismic loadings, and results of flow distribution testing that supported the CRBR design effort. The approach taken to simplify fabrication of the CRBR components, and a novel 20 inch deep narrow gap weld joint in the CSS are described

  19. Choosing Staff Members Reduces Time in Mechanical Restraint Due to Self-Injurious Behaviour and Requesting Restraint

    Science.gov (United States)

    Jensen, Craig C.; Lydersen, Tore; Johnson, Paul R.; Weiss, Shannon R.; Marconi, Michael R.; Cleave, Mary L.; Weber, Patricia

    2012-01-01

    Background: Using mechanical restraints to protect a person who engaged in dangerous self-injury was decreased by manipulation of an establishing operation involving the client choosing the staff person who would work with her. Materials and Methods: The client was a 28-year-old woman diagnosed with autism, bipolar disorder, static cerebral…

  20. Mental Health Nursing, Mechanical Restraint Measures and Patients’ Legal Rights

    DEFF Research Database (Denmark)

    Birkeland, Søren; Gildberg, Frederik Alkier

    2016-01-01

    Abstract: Coercive mechanical restraint (MR) in psychiatry constitute the perhaps most important exception from the common health law requirement for involving patients in health care decisions and achieving their informed consent prior to treatment. Coercive measures and particularly MR constitute...... a serious collision with patient autonomy principles, pose a particular challenge to psychiatric patients’ legal rights, and put intensified demands on health professional performance. Legal rights principles require rationale for coercive measure use be thoroughly considered and rigorously documented....... This article presents an in-principle Danish Psychiatric Complaint Board decision concerning MR use initiated by untrained staff. The case illustrates that, judicially, weight must be put on the patient perspective on course of happenings and especially when health professional documentation is scant, patients...

  1. Overview of PEC core design and requirements for PEC core restraint systems

    International Nuclear Information System (INIS)

    Cecchini, F.

    1984-01-01

    The Italian PEC reactor is an experimental loop type fast reactor of 120 MW thermal. Its main purpose is the in-pile development of fast reactor fuel. The mechanical principles in PEC core design and current modifications to ensure a safe seismic perturbation and shutdown are discussed in this paper. These anti-seismic modifications are aimed to limit the extent of reactivity perturbation during the seismic event and to guarantee control rod entry at any time during the seismic event

  2. Adjustable, physiological ventricular restraint improves left ventricular mechanics and reduces dilatation in an ovine model of chronic heart failure.

    Science.gov (United States)

    Ghanta, Ravi K; Rangaraj, Aravind; Umakanthan, Ramanan; Lee, Lawrence; Laurence, Rita G; Fox, John A; Bolman, R Morton; Cohn, Lawrence H; Chen, Frederick Y

    2007-03-13

    Ventricular restraint is a nontransplantation surgical treatment for heart failure. The effect of varying restraint level on left ventricular (LV) mechanics and remodeling is not known. We hypothesized that restraint level may affect therapy efficacy. We studied the immediate effect of varying restraint levels in an ovine heart failure model. We then studied the long-term effect of restraint applied over a 2-month period. Restraint level was quantified by use of fluid-filled epicardial balloons placed around the ventricles and measurement of balloon luminal pressure at end diastole. At 4 different restraint levels (0, 3, 5, and 8 mm Hg), transmural myocardial pressure (P(tm)) and indices of myocardial oxygen consumption (MVO2) were determined in control (n=5) and ovine heart failure (n=5). Ventricular restraint therapy decreased P(tm) and MVO2, and improved mechanical efficiency. An optimal physiological restraint level of 3 mm Hg was identified to maximize improvement without an adverse affect on systemic hemodynamics. At this optimal level, end-diastolic P(tm) and MVO2 indices decreased by 27% and 20%, respectively. The serial longitudinal effects of optimized ventricular restraint were then evaluated in ovine heart failure with (n=3) and without (n=3) restraint over 2 months. Optimized ventricular restraint prevented and reversed pathological LV dilatation (130+/-22 mL to 91+/-18 mL) and improved LV ejection fraction (27+/-3% to 43+/-5%). Measured restraint level decreased over time as the LV became smaller, and reverse remodeling slowed. Ventricular restraint level affects the degree of decrease in P(tm), the degree of decrease in MVO2, and the rate of LV reverse remodeling. Periodic physiological adjustments of restraint level may be required for optimal restraint therapy efficacy.

  3. Structural evaluation of fast reactor core restraint with irradiation creep-swelling opposition effects

    International Nuclear Information System (INIS)

    Kalinowski, J.E.

    1979-01-01

    Irradiation creep and swelling correlations are derived from primary loading in-reactor experiments in which irradiation creep and swelling act in the same direction. When correlation uncertainty bands are applied in core restraint evaluations, significant variability in sub-assembly behavior is predicted. For example, sub-assemblies in the outer core region where neutron flux and duct temperature gradients are significant exhibit bowing responses ranging from a creep dominated outward bow to a swelling dominated inward bow. Furthermore, solutions based on upper bound and lower bound correlation uncertainty combinations are observed to cross-over indicating that such combinations are physically unrealistic in the assessment of creep-swelling opposition effects. In order to obtain realistic upper and lower bound sub-assembly responses, judgement must be applied in the selection of creep-swelling equation uncertainty combinations. Experimental programs have been defined which will provide the needed basic as well as prototypic creep-swelling opposition data for reference and advanced sub-assembly duct alloys. The first of these is an irradiation of cylindrical capsules subjected to a through-wall temperature gradient. This test which is presently underway in the EBR-II reactor will provide the data needed to refine irradiation creep and swelling correlations and their associated uncertainties when applied to core restraint evaluations. Restrained pin and duct bowing experiments in FFTF have also been defined. These will provide the prototypic data necessary to verify irradiated duct bowing methodology. The results of this experimental program are expected to reduce creep and swelling uncertainties and permit better definition of the design window for load plane gaps. (orig.)

  4. Forensic mental health clinician's experiences with and assessment of alliance regarding the patient's readiness to be released from mechanical restraint

    DEFF Research Database (Denmark)

    Nielsen, Lea Deichmann; Gildberg, Frederik Alkier; Bech, Per

    2018-01-01

    One of the main reasons for prolonged duration of mechanical restraint is patient behaviour in relation to the clinician-patient alliance. This article reports on the forensic mental health clinicians experiences of the clinician-patient alliance during mechanical restraint, and their assessment...

  5. Nuclear reactor support and seismic restraint with in-vessel core retention cooling features

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, Tyler A.; Edwards, Michael J.

    2018-01-23

    A nuclear reactor including a lateral seismic restraint with a vertically oriented pin attached to the lower vessel head and a mating pin socket attached to the floor. Thermally insulating materials are disposed alongside the exterior surface of a lower portion of the reactor pressure vessel including at least the lower vessel head.

  6. Resisting force characteristics of a mechanical snubber and its restraint effect on beam deformation

    International Nuclear Information System (INIS)

    Ohmata, Kenichiro

    1987-01-01

    A mechanical snubber is used to restrain piping systems in nuclear power plants during an earthquake. It has nonlinearities in both load (or exciting amplitude) and frequency response, so it will be very difficult to analyze the resisting force characteristics of the mechanical snubber theoretically. In this report, the equation of motion of the mechanical snubber is derived and digital simulations of snubber dynamic characteristics over a frequency range are carried out using the Continuous System Simulation Language (CSSL). Also, the restraint effect of the mechanical snubber applied to a simple beam is discussed both numerically and experimentally. The beam is replaced by a lumped mass system and CSSL is used to perform the digital simulations. (author)

  7. [Effects of a training of power and balance on the use of mechanical restraint among in-patients with dementia].

    Science.gov (United States)

    Steinert, Tilman; Bohnet, Ulrich; Flammer, Erich; Lüchtenberg, Dietmar; Eisele, Frank

    2009-09-01

    Patients with dementia are most frequently affected by mechanical restraint in psychiatric hospitals, most frequently due to falls. There is evidence for beneficial effects of a training of power and balance on the frequency of falls in residential homes. An adapted training of power and balance was developed by specialists of training in sports. In 2007, 159 patients with dementia were trained. The frequency and duration of mechanical restraint was compared with a control group of a different hospital (n = 217) and the patients treated in the year before (n = 164). The percentage of patients with mechanical restraint and the mean duration of restraint per admission were significantly lower than in the control group. However, only a non-significant reduction could be achieved in comparison with the patients treated in the year before without an increase of falls. A considerable reduction of the use of mechanical restraint in patients with dementia is feasible. An unequivocal association with the training could not be confirmed due to other influencing factors.

  8. 'Mechanical restraint-confounders, risk, alliance score': testing the clinical validity of a new risk assessment instrument.

    Science.gov (United States)

    Deichmann Nielsen, Lea; Bech, Per; Hounsgaard, Lise; Alkier Gildberg, Frederik

    2017-08-01

    Unstructured risk assessment, as well as confounders (underlying reasons for the patient's risk behaviour and alliance), risk behaviour, and parameters of alliance, have been identified as factors that prolong the duration of mechanical restraint among forensic mental health inpatients. To clinically validate a new, structured short-term risk assessment instrument called the Mechanical Restraint-Confounders, Risk, Alliance Score (MR-CRAS), with the intended purpose of supporting the clinicians' observation and assessment of the patient's readiness to be released from mechanical restraint. The content and layout of MR-CRAS and its user manual were evaluated using face validation by forensic mental health clinicians, content validation by an expert panel, and pilot testing within two, closed forensic mental health inpatient units. The three sub-scales (Confounders, Risk, and a parameter of Alliance) showed excellent content validity. The clinical validations also showed that MR-CRAS was perceived and experienced as a comprehensible, relevant, comprehensive, and useable risk assessment instrument. MR-CRAS contains 18 clinically valid items, and the instrument can be used to support the clinical decision-making regarding the possibility of releasing the patient from mechanical restraint. The present three studies have clinically validated a short MR-CRAS scale that is currently being psychometrically tested in a larger study.

  9. eLearning course may shorten the duration of mechanical restraint among psychiatric inpatients: a cluster-randomized trial.

    Science.gov (United States)

    Kontio, Raija; Pitkänen, Anneli; Joffe, Grigori; Katajisto, Jouko; Välimäki, Maritta

    2014-10-01

    The management of psychiatric inpatients exhibiting severely disturbed and aggressive behaviour is an important educational topic. Well structured, IT-based educational programmes (eLearning) often ensure quality and may make training more affordable and accessible. The aim of this study was to explore the impact of an eLearning course for personnel on the rates and duration of seclusion and mechanical restraint among psychiatric inpatients. In a cluster-randomized intervention trial, the nursing personnel on 10 wards were randomly assigned to eLearning (intervention) or training-as-usual (control) groups. The eLearning course comprised six modules with specific topics (legal and ethical issues, behaviour-related factors, therapeutic relationship and self-awareness, teamwork and integrating knowledge with practice) and specific learning methods. The rates (incidents per 1000 occupied bed days) and durations of the coercion incidents were examined before and after the course. A total of 1283 coercion incidents (1143 seclusions [89%] and 140 incidents involving the use of mechanical restraints [11%]) were recorded on the study wards during the data collection period. On the intervention wards, there were no statistically significant changes in the rates of seclusion and mechanical restraint. However, the duration of incidents involving mechanical restraints shortened from 36.0 to 4.0 h (median) (P eLearning course, the duration of incidents involving the use of mechanical restraints decreased. However, more studies are needed to ensure that the content of the course focuses on the most important factors associated with the seclusion-related elements. The eLearning course deserves further development and further studies. The duration of coercion incidents merits attention in future research.

  10. Clean Development Mechanism: Core of Kyoto Mechanism

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Myung Kyun [United Nations Environment Programme (Denmark)

    2000-06-01

    Kyoto protocol is a foundation for achieving an ultimate goal of UNFCCC, which is to stabilizing greenhouse gas concentration in the air. The clean development system is a core element for successful implementation of Kyoto protocol with other Kyoto mechanisms. While UNFCCC requires a new paradigm changing to sustainable development considering demand and future environment from the past supply-oriented resource consumption, the clean development system will be used as a means of successful establishment of a new paradigm in 21st century. As environmental problem is integrated with economic problem and each country is thriving for securing its own economic benefit in the issue of environmental conservation, Korea should do its best to have both of global environmental conservation and economic benefit for its own. 1 tab.

  11. Physical and mechanical restraint in psychiatric units: Perceptions and experiences of nursing staff.

    Science.gov (United States)

    Vedana, Kelly Graziani Giacchero; da Silva, Danielle Maria; Ventura, Carla Aparecida Arena; Giacon, Bianca Cristina Ciccone; Zanetti, Ana Carolina Guidorizzi; Miasso, Adriana Inocenti; Borges, Tatiana Longo

    2018-06-01

    Physical restraint in psychiatric units is a common practice but extremely controversial and poorly evaluated by methodologically appropriate investigations. The cultural issues and professionals' perceptions and attitudes are substantial contributors to the frequency of restraint that tend to be elevated. Aim In this qualitative study, we aimed to understand the experiences and perceptions of nursing staff regarding physical restraint in psychiatric units. Through theoretical sampling, 29 nurses from two Brazilian psychiatric units participated in the study. Data were collected from 2014 to 2016 from individual interviews and analyzed through thematic analysis, employing theoretical presuppositions of symbolic interactionism. Physical restraint was considered unpleasant, challenging, risky, and associated with dilemmas and conflicts. The nursing staff was often exposed to the risks and injuries related to restraint. Professionals sought strategies to reduce restraint-related damages, but still considered it necessary due to the lack of effective options to control aggressive behavior. This study provides additional perspectives about physical restraint and reveals the need for safer, humanized and appropriate methods for the care of aggressive patients that consider the real needs and rights of these patients. Copyright © 2017 Elsevier Inc. All rights reserved.

  12. The effect of mechanical restraint on the deformation of Zircaloy cladding

    International Nuclear Information System (INIS)

    Jones, P.M.; Haste, T.J.

    1980-10-01

    Zircaloy cladding, deformed at temperatures postulated for loss-of-coolant accidents, can exhibit considerable ductility. The actual circumferential strain is governed by the temperature uniformity around the rod during the time at which the major part of the deformation occurs. If the bulges in neighbouring rods in a multi-rod array touch before rupture, and the array is large enough for the outer rods to restrain bulges rather than be pushed away by them, then the stress in such bulges drops. However the stress in adjacent axial regions of the cladding which have not contacted remains high and these continue to strain until they also interact, thus propagating the bulging axially. Meanwhile the non-contacted portions of the interacting bulges continue to strain slowly into the remaining sub-channels. Illustrative calculations suggest that the mechanical restraint of bulging cladding will only be effective in increasing sub-channel blockage when the failure strains are greater than 60-70%. This may occur with temperature differences between neighbouring rods of 10-25 0 C if the deformation process is thermally stabilised. (author)

  13. Thermal hydraulics and mechanics core design programs

    International Nuclear Information System (INIS)

    Heinecke, J.

    1992-10-01

    The report documents the work performed within the Research and Development Task T hermal hydraulics and mechanics core design programs , funded by the German government. It contains the development of new codes, the extension of existing codes, the qualification and verification of codes and the development of a code library. The overall goal of this work was to adapt the system of thermal hydraulics and mechanics codes to the permanently growing requirements of the status of science and technology

  14. Waves in the core and mechanical core-mantle interactions

    DEFF Research Database (Denmark)

    Jault, D.; Finlay, Chris

    2015-01-01

    This Chapter focuses on time-dependent uid motions in the core interior, which can beconstrained by observations of the Earth's magnetic eld, on timescales which are shortcompared to the magnetic diusion time. This dynamics is strongly inuenced by the Earth's rapid rotation, which rigidies...... the motions in the direction parallel to the Earth'srotation axis. This property accounts for the signicance of the core-mantle topography.In addition, the stiening of the uid in the direction parallel to the rotation axis gives riseto a magnetic diusion layer attached to the core-mantle boundary, which would...... otherwisebe dispersed by Alfven waves. This Chapter complements the descriptions of large-scaleow in the core (8.04), of turbulence in the core (8.06) and of core-mantle interactions(8.12), which can all be found in this volume. We rely on basic magnetohydrodynamictheory, including the derivation...

  15. Mechanical core coupling and reactors stability

    International Nuclear Information System (INIS)

    Suarez Antola, R.

    2006-01-01

    Structural parts of nuclear reactors are complex mechanical systems, able to vibrate with a set of proper frequencies when suitably excited. Cyclical variations in the strain state of the materials, including density perturbations, are produced. This periodic changes may affect reactor reactivity. But a variation in reactivity affects reactor thermal power, thus modifying the temperature field of the abovementiones materials. If the variation in temperature fields is fast enough, thermal-mechanical coupling may produce fast variations in strain states, and this, at its turn, modifies the reactivity, and so on. This coupling between mechanical vibrations of the structure and the materials of the core, with power oscillations of the reactor, not only may not be excluded a priori, but it seems that it has been present in some stage of the incidents or accidents that happened during the development of nuclear reactor technology. The purpose of the present communication is: (a) To review and generalize some mathematical models that were proposed in order to describe thermal-mechanical coupling in nuclear reactors. (b) To discuss some conditions in which significant instabilities could arise, including large amplitude power oscillations coupled with mechanical vibrations whose amplitudes are too small to be excluded by conventional criteria of mechanical design. Enough Certain aspects of thr physical safety of nuclear power reactors, that are objected by people that opposes to the renaissance of nucleoelectric generation, are discussed in the framework of the mathematical model proposed in this paper [es

  16. In-core monitor drive mechanism

    International Nuclear Information System (INIS)

    Hattori, Kunimitsu; Ishii, Yoshimi.

    1969-01-01

    Instruments for measuring the neutron flux in a reactor are hung at the upper end of a shuttle tube connected to the upper portion of a perforated tube a plurality of the holes of which are engaged at all times with the teeth of an endless chain. The endless chain is driven by a sprocket integrated with a worm wheel shaft driven by a motor through a flexible shaft. The perforated tube is capable of being smoothly driven vertically into the reactor core without causing any noise. Since the tube is driven through a plurality of the teeth of the endless chain, the dimensions of the sprockets and other associated parts can be reduced to make the entire drive mechanism more compact. (Ohno, Y.)

  17. Antidepressant-Like Effects of Vaccinium bracteatum in Chronic Restraint Stress Mice: Functional Actions and Mechanism Explorations.

    Science.gov (United States)

    Oh, Dool-Ri; Kim, Yujin; Choi, Eun-Jin; Jung, Myung-A; Oh, Kyo-Nyeo; Hong, Ji-Ae; Bae, Donghyuck; Kim, Kwangsu; Kang, Huwon; Kim, Jaeyong; Kim, Young Ran; Cho, Seung Sik; Choi, Chul-Young

    2018-01-01

    The fruit of Vaccinium bracteatum Thunb. (VBF) is commonly known as the oriental blueberry in Korea. The aim of this study was to evaluate the antidepressant-like effects of water VBF extract (VBFW) in a mouse model of chronic restraint stress (CRS) and to identify the underlying mechanisms of its action. The behavioral effects of VBFW were assessed in the forced swim test (FST) and open field test (OFT). The levels of serum corticosterone (CORT), brain monoamines, in addition to the extracellular signal-regulated kinases (ERKs)/protein kinase B (Akt) signaling pathway were evaluated. VBFW treatment significantly reduced the immobility time and increased swimming time in FST without altering the locomotor activity in unstressed mice. Furthermore, CRS mice treated with VBFW exhibited a significantly decreased immobility time in FST and serum CORT, increased locomotor activity in OFT, and enhanced brain monoamine neurotransmitters. Similarly, VBFW significantly upregulated the ERKs/Akt signaling pathway in the hippocampus and PFC. In addition, VBFW may reverse CORT-induced cell death by enhancing cyclic AMP-responsive element-binding protein expression through the up-regulation of ERKs/Akt signaling pathways. In addition, VBFW showed the strong antagonistic effect of the 5-HT[Formula: see text] receptor by inhibiting 5-HT-induced intracellular Ca[Formula: see text] and ERK1/2 phosphorylation. Our study provides evidence that antidepressant-like effects of VBFW might be mediated by the regulation of monoaminergic systems and glucocorticoids, which is possibly associated with neuroprotective effects and antagonism of 5-HT[Formula: see text] receptor.

  18. Introducing mechanics by tapping core causal knowledge

    International Nuclear Information System (INIS)

    Klaassen, Kees; Westra, Axel; Emmett, Katrina; Eijkelhof, Harrie; Lijnse, Piet

    2008-01-01

    This article concerns an outline of an introductory mechanics course. It is based on the argument that various uses of the concept of force (e.g. from Kepler, Newton and everyday life) share an explanatory strategy based on core causal knowledge. The strategy consists of (a) the idea that a force causes a deviation from how an object would move of its own accord (i.e. its force-free motion), and (b) an incentive to search, where the motion deviates from the assumed force-free motion, for recurring configurations with which such deviations can be correlated (interaction theory). Various assumptions can be made concerning both the force-free motion and the interaction theory, thus giving rise to a variety of specific explanations. Kepler's semi-implicit intuition about the force-free motion is rest, Newton's explicit assumption is uniform rectilinear motion, while in everyday explanations a diversity of pragmatic suggestions can be recognized. The idea is that the explanatory strategy, once made explicit by drawing on students' intuitive causal knowledge, can be made to function for students as an advance organizer, in the sense of a general scheme that they recognize but do not yet know how to detail for scientific purposes

  19. Protective effect of Momordica charantia water extract against liver injury in restraint-stressed mice and the underlying mechanism.

    Science.gov (United States)

    Deng, Yuanyuan; Tang, Qin; Zhang, Yan; Zhang, Ruifen; Wei, Zhencheng; Tang, Xiaojun; Zhang, Mingwei

    2017-01-01

    Background : Momordica charantia is used in China for its jianghuo (heat-clearing and detoxifying) effects. The concept of shanghuo (the antonym of jianghuo , excessive internal heat) in traditional Chinese medicine is considered a type of stress response of the body. The stress process involves internal organs, especially the liver. Objective : We hypothesized that Momordica charantia water extract (MWE) has a hepatoprotective effect and can protect the body from stress. The aim of this study was to investigate the possible effects of MWE against liver injury in restraint-stressed mice. Design : The mice were intragastrically administered with MWE (250, 500 and 750 mg/kg bw) daily for 7 days. The Normal Control (NC) and Model groups were administered distilled water. A positive control group was intragastrically administered vitamin C 250 mg/kg bw. After the last administration, mice were restrained for 20 h. Results : MWE reduced the serum AST and ALT, reduced the NO content and the protein expression level of iNOSin the liver; significantly reduced the mitochondrial ROS content, increased the mitochondrial membrane potential and the activities of mitochondrial respiratory chain complexes I and II in restraint-stressed mice. Conclusions : The results indicate that MWE has a protective effect against liver injury in restraint-stressed mice. Abbreviations : MWE: Momordica charantia water extract; M. charantia: Momordica charantia L.; ROS: reactive oxygen species; NO: nitric oxide; iNOS: inducible nitric oxide synthase; IL-1β: interleukin-1 beta; TNF-α: tumor necrosis factor alpha; IL-6: interleukin 6; IFN-γ: interferon gamma; VC: vitamin C; ALT: alanine transaminase; AST: aspartate aminotransferase; GSH: glutathione; GSH-PX: glutathione peroxidase; MDA: malondialdehyde; BCA: bicinchoninic acid; TBARS: thiobarbituric acid reactive substances; Trolox: 6-hydroxy-2,5,7,8-tetramethylchroman-2-carboxylic acid; JC-B: Janus Green B; DW: dry weight; FC: Folin

  20. Lateral restraint assembly in a nuclear reactor

    International Nuclear Information System (INIS)

    Brown, S.J.; Gorholt, W.

    1977-01-01

    A lateral restraint assembly is described for a reactor of, for example, the high temperature gas-cooled type which commonly includes a reactor core of relatively complex construction supported within a shell or vessel providing a shielded cavity for containing the reactor core. (U.K.)

  1. Praying Mantis Bending Core Breakoff and Retention Mechanism

    Science.gov (United States)

    Badescu, Mircea; Sherrit, Stewart; Bar-Cohen, Yoseph; Bao, Xiaoqi; Lindermann, Randel A.

    2011-01-01

    Sampling cores requires the controlled breakoff of the core at a known location with respect to the drill end. An additional problem is designing a mechanism that can be implemented at a small scale, yet is robust and versatile enough to be used for a variety of core samples. The new design consists of a set of tubes (a drill tube, an outer tube, and an inner tube) and means of sliding the inner and outer tubes axially relative to each other. Additionally, a sample tube can be housed inside the inner tube for storing the sample. The inner tube fits inside the outer tube, which fits inside the drill tube. The inner and outer tubes can move axially relative to each other. The inner tube presents two lamellae with two opposing grabbing teeth and one pushing tooth. The pushing tooth is offset axially from the grabbing teeth. The teeth can move radially and their motion is controlled by the outer tube. The outer tube presents two lamellae with radial extrusions to control the inner tube lamellae motion. In breaking the core, the mechanism creates two support points (the grabbing teeth and the bit tip) and one push point. The core is broken in bending. The grabbing teeth can also act as a core retention mechanism. The praying mantis that is disclosed herein is an active core breaking/retention mechanism that requires only one additional actuator other than the drilling actuator. It can break cores that are attached to the borehole bottom as

  2. General presentation of the core mechanical behaviour approach in France

    International Nuclear Information System (INIS)

    Bernard, A.; Dorsselaere, J.P. van

    1984-01-01

    This French review paper presents the evolution along time of the FBR core mechanical behaviour approach, from RAPSODIE to SPX2, through PHENIX and SPX1: core designs, knowledge of the irradiation laws, project criterias, calculation codes, and R and D fields. (author)

  3. The TMI-2 core relocation: Heat transfer and mechanism

    International Nuclear Information System (INIS)

    Epstein, M.; Fauske, H.K.

    1987-07-01

    It is postulated that the collapse of the upper debris bed was the main cause of core failure and core material relocation during the TMI-2 accident. It is shown that this mechanism of core relocation can account for the timescale(s) and energy transfer rate inferred from plant instrumentation. Additional analysis suggests that the water in the lower half of the reactor vessel was subcooled at the onset of relocation, as subcooling serves to explain the final coolable configuration at the bottom of the TMI vessel

  4. Failure mechanisms for compacted uranium oxide fuel cores

    International Nuclear Information System (INIS)

    Berghaus, D.G.; Peacock, H.B.

    1980-01-01

    Tension, compression, and shear tests were performed on test specimens of aluminum-clad, compacted powder fuel cores to determine failure mechanisms of the core material. The core, which consists of 70% uranium oxide in an aluminum matrix, frequently fails during post-extrusion drawing. Tests were conducted to various strain levels up to failure of the core. Sections were made of tested specimens to microscopically study initiation of failure. Two failure modes wee observed. Tensile failure mode is initiated by prior tensile failure of uranium oxide particles with the separation path strongly influenced by the arrangement of particles. Delamination mode consists of the separation of laminae formed during extrusion of tubes. Separation proceeds from fine cracks formed parallel to the laminae. Tensile failure mode was experienced in tension and shear tests. Delamination mode was produced in compression tests

  5. Rolling-Tooth Core Breakoff and Retention Mechanism

    Science.gov (United States)

    Badescu, Mircea; Bickler, Donald B.; Sherrit, Stewart; Bar-Cohen, Yoseph; Bao, Xiaoqi; Hudson, Nicolas H.

    2011-01-01

    Sampling cores requires the controlled breakoff of the core at a known location with respect to the drill end. An additional problem is designing a mechanism that can be implemented at a small scale that is robust and versatile enough to be used for a variety of core samples. This design consists of a set of tubes (a drill tube and an inner tube) and a rolling element (rolling tooth). An additional tube can be used as a sample tube. The drill tube and the inner tube have longitudinal holes with the axes offset from the axis of each tube. The two eccentricities are equal. The inner tube fits inside the drill tube, and the sample tube fits inside the inner tube. While drilling, the two tubes are positioned relative to each other such that the sample tube is aligned with the drill tube axis and core. The drill tube includes teeth and flutes for cuttings removal. The inner tube includes, at the base, the rolling element implemented as a wheel on a shaft in an eccentric slot. An additional slot in the inner tube and a pin in the drill tube limit the relative motion of the two tubes. While drilling, the drill assembly rotates relative to the core and forces the rolling tooth to stay hidden in the slot along the inner tube wall. When the drilling depth has been reached, the drill bit assembly is rotated in the opposite direction, and the rolling tooth is engaged and penetrates into the core. Depending on the strength of the created core, the rolling tooth can score, lock the inner tube relative to the core, start the eccentric motion of the inner tube, and break the core. The tooth and the relative position of the two tubes can act as a core catcher or core-retention mechanism as well. The design was made to fit the core and hole parameters produced by an existing bit; the parts were fabricated and a series of demonstration tests were performed. This invention is potentially applicable to sample return and in situ missions to planets such as Mars and Venus, to moons such

  6. Investigation of failure mechanisms for HTGR core supports

    International Nuclear Information System (INIS)

    Bennett, J.G.; Ju, F.D.; Anderson, C.A.

    1976-12-01

    The report is concerned with potential instabilities of High-Temperature Gas-Cooled Reactor Cores supported by graphite columns. Two failure mechanisms are investigated in detail: that of torsional buckling of the entire core-column assemblage and that of column failure alone. A torsional model of the core-column assemblage is described and static buckling loads are calculated. Dynamic instability of the model to seismic loadings is also investigated. Individual column failure is examined using nonlinear graphite behavior and safety factors for static loading situations are given and compared to values given by conventional design formulas. A model of a cracked graphite column is given and buckling loads are computed for columns using a combined column and fracture mechanics analysis. A finite element analysis of a cracked graphite column is presented

  7. The European strategy for fast reactor core static mechanics studies

    International Nuclear Information System (INIS)

    Jones, C.H.; Di Francesca, R.; Coors, D.; Steenberghe, T. van

    1987-01-01

    The strategy is designed to meet the needs of participating European countries by achieving the following objectives: To provide generic information and data on the static mechanics of all styles of core of interest, validate codes and optimise new designs. To endorse specific features of SPX2 and SNR2 designs. To provide the new facilities which are needed. To present the programme of work required and timescale. (orig./HP)

  8. Tunable engineered skin mechanics via coaxial electrospun fiber core diameter.

    Science.gov (United States)

    Blackstone, Britani Nicole; Drexler, Jason William; Powell, Heather Megan

    2014-10-01

    Autologous engineered skin (ES) offers promise as a treatment for massive full thickness burns. Unfortunately, ES is orders of magnitude weaker than normal human skin causing it to be difficult to apply surgically and subject to damage by mechanical shear in the early phases of engraftment. In addition, no manufacturing strategy has been developed to tune ES biomechanics to approximate the native biomechanics at different anatomic locations. To enhance and tune ES biomechanics, a coaxial (CoA) electrospun scaffold platform was developed from polycaprolactone (PCL, core) and gelatin (shell). The ability of the coaxial fiber core diameter to control both scaffold and tissue mechanics was investigated along with the ability of the gelatin shell to facilitate cell adhesion and skin development compared to pure gelatin, pure PCL, and a gelatin-PCL blended fiber scaffold. CoA ES exhibited increased cellular adhesion and metabolism versus PCL alone or gelatin-PCL blend and promoted the development of well stratified skin with a dense dermal layer and a differentiated epidermal layer. Biomechanics of the scaffold and ES scaled linearly with core diameter suggesting that this scaffold platform could be utilized to tailor ES mechanics for their intended grafting site and reduce graft damage in vitro and in vivo.

  9. Tunable Engineered Skin Mechanics via Coaxial Electrospun Fiber Core Diameter

    Science.gov (United States)

    Blackstone, Britani Nicole; Drexler, Jason William

    2014-01-01

    Autologous engineered skin (ES) offers promise as a treatment for massive full thickness burns. Unfortunately, ES is orders of magnitude weaker than normal human skin causing it to be difficult to apply surgically and subject to damage by mechanical shear in the early phases of engraftment. In addition, no manufacturing strategy has been developed to tune ES biomechanics to approximate the native biomechanics at different anatomic locations. To enhance and tune ES biomechanics, a coaxial (CoA) electrospun scaffold platform was developed from polycaprolactone (PCL, core) and gelatin (shell). The ability of the coaxial fiber core diameter to control both scaffold and tissue mechanics was investigated along with the ability of the gelatin shell to facilitate cell adhesion and skin development compared to pure gelatin, pure PCL, and a gelatin-PCL blended fiber scaffold. CoA ES exhibited increased cellular adhesion and metabolism versus PCL alone or gelatin-PCL blend and promoted the development of well stratified skin with a dense dermal layer and a differentiated epidermal layer. Biomechanics of the scaffold and ES scaled linearly with core diameter suggesting that this scaffold platform could be utilized to tailor ES mechanics for their intended grafting site and reduce graft damage in vitro and in vivo. PMID:24712409

  10. Contribution to the explanation of the spalling of small specimen without any mechanical restraint exposed to high temperature

    International Nuclear Information System (INIS)

    Morais, Marcus V.G. de; Pliya, Prosper; Noumowe, Albert; Beaucour, Anne-Lise; Ortola, Sophie

    2010-01-01

    The behaviour of concrete subjected to high temperature is studied. The aim of the study is to explain the spalling or bursting phenomenon observed during experimental studies in the laboratory. Mechanical computations are carried out with the finite element code CAST3M developed at the French Atomic Energy Agency (CEA). Heat gradient and water vapour pressure inside the concrete element are determined by using a thermo-hydrous model. Then, the mechanical stresses generated in the studied concrete element are calculated according to two behaviour assumptions: the linear isotropic elastic law and an elastoplastic model. Numerical simulations show that, during the heating cycles, tension stresses are developed in the central part and compression stresses at the surface of the cylindrical concrete element. The highest stresses appear when the surface temperature of the concrete element is about 300 o C. The tension stresses in the specimens then exceed the concrete tensile strength.

  11. Contribution to the explanation of the spalling of small specimen without any mechanical restraint exposed to high temperature

    Energy Technology Data Exchange (ETDEWEB)

    Morais, Marcus V.G. de, E-mail: mvmorais@unb.b [Cergy-Pontoise University - L2MGC, 5 mail Gay-Lussac Neuville sur Oise, 95031 Cergy-Pontoise Cedex (France); Pliya, Prosper [Cergy-Pontoise University - L2MGC, 5 mail Gay-Lussac Neuville sur Oise, 95031 Cergy-Pontoise Cedex (France); Noumowe, Albert, E-mail: Albert.Noumowe@u-cergy.f [Cergy-Pontoise University - L2MGC, 5 mail Gay-Lussac Neuville sur Oise, 95031 Cergy-Pontoise Cedex (France); Beaucour, Anne-Lise; Ortola, Sophie [Cergy-Pontoise University - L2MGC, 5 mail Gay-Lussac Neuville sur Oise, 95031 Cergy-Pontoise Cedex (France)

    2010-10-15

    The behaviour of concrete subjected to high temperature is studied. The aim of the study is to explain the spalling or bursting phenomenon observed during experimental studies in the laboratory. Mechanical computations are carried out with the finite element code CAST3M developed at the French Atomic Energy Agency (CEA). Heat gradient and water vapour pressure inside the concrete element are determined by using a thermo-hydrous model. Then, the mechanical stresses generated in the studied concrete element are calculated according to two behaviour assumptions: the linear isotropic elastic law and an elastoplastic model. Numerical simulations show that, during the heating cycles, tension stresses are developed in the central part and compression stresses at the surface of the cylindrical concrete element. The highest stresses appear when the surface temperature of the concrete element is about 300 {sup o}C. The tension stresses in the specimens then exceed the concrete tensile strength.

  12. Comparing the effect of non-medical mechanical restraint preventive factors between psychiatric units in Denmark and Norway

    DEFF Research Database (Denmark)

    Bak, Jesper; Zoffmann, V.; Sestoft, D.M.

    2015-01-01

    was not supported by earlier research, the identification of the patient's crisis triggers; therefore, more research on the mechanisms involved is needed. CLINICAL IMPLICATIONS: None of the six MR preventive factors presents any adverse effects; therefore, units in Denmark and Norway may consider investigating......-medical origin may explain the differing number of MR episodes between Denmark and Norway. METHODS: This study is a cross-sectional survey of psychiatric units. Linear regression was used to assess the confounding effects of the MR preventive factors, i.e. whether a difference in the impact of these factors...... the effect of implementing, the identification of the patient's crisis triggers, an increased number of staff per patient, increased staff education, a better work environment and reduced use of substitute staff in practice....

  13. Review of coaxial flow gas core nuclear rocket fluid mechanics

    International Nuclear Information System (INIS)

    Weinstein, H.

    1976-01-01

    In a prematurely aborted attempt to demonstrate the feasibility of using a gas core nuclear reactor as a rocket engine, NASA initiated a number of studies on the relevant fluid mechanics problems. These studies were carried out at NASA laboratories, universities and industrial research laboratories. Because of the relatively sudden termination of most of this work, a unified overview was never presented which demonstrated the accomplishments of the program and pointed out the areas where additional work was required for a full understanding of the cavity flow. This review attempts to fulfill a part of this need in two important areas

  14. Evaluating the Effect of a Mechanical Adjunct to Improve the Installation of Child Restraint Systems to Vehicles.

    Science.gov (United States)

    Mirman, Jessica H; Seifert, Sara J; Zonfrillo, Mark R; Metzger, Kristi; Durbin, Dennis R; Arbogast, Kristy B

    2015-01-01

    We explored if an alternative CRS design that utilized a mechanical adjunct to amplify the force applied to the adult seat belt (intervention CRS) results in more accurate and secure attachment between the CRS and the vehicle compared to similar CRS models that use LATCH or the existing adult seat belt. We conducted three separate studies to address this question and additionally explored: (1) the contribution of prior CRS installation experience (Study 1), (2) the value-added of CRS labeling (Study 2), and (3) paper-based vs. video instructions (Study 3). In Studies 1 and 2 we assessed a forward facing combination CRS design (intervention CRS) compared to a commercially available LATCH equipped model (control CRS) and in Study 3 we conducted a similar study using a convertible model of both the intervention and control CRS. Participants installed both CRS in a contemporary minivan and could choose which type of attachment to use for the control CRS (LATCH or seat belt); order of installation was counter-balanced. Evaluators systematically examined installations for accuracy and security. Study 1: A greater proportion of participants in both the experienced and inexperienced groups was able to securely install the intervention CRS compared to the control CRS: (45% vs. 16%, p =.0001 for experienced) and (37% vs. 6%, p =.003 for inexperienced). No differences between the CRS were observed for accuracy of installation in either user group. Study 2: A greater proportion of participants were able to securely install the enhanced intervention CRS compared to the control CRS: (62% vs. 9%, p =.001). The intervention CRS demonstrated reduced installation accuracy: (30% vs. 61%, p =.001). Study 3: A greater proportion of participants was able to securely install the intervention CRS compared to the control CRS: 79% vs. 66% p =.03, but this effect was smaller than in the previous studies. Participants were less likely to achieve an accurate installation with the intervention

  15. Study of the mechanism of clamping and detachment of a core sample by core lever lifters

    Energy Technology Data Exchange (ETDEWEB)

    Barabashkin, I I; Mizyakin, V M; Nikitin, S V

    1981-01-01

    Geometric dimensions of the basic elements of a core lifter should be determined depending on the clamping conditions. The changes should be determined depending on the conditions of the core sample diameter, critical angle between the lever and the core samples in the necessary depth of submersion of the contact edge of the lever into its surface. The core lifter KTsRZ-80 with eccentric core reception makes it possible to arrange more efficiently the core removing elements on the edge of the band. The use of the core lifters with eccentric plan of arrangement of the levers and their optimal length increases the removal of the core sample.

  16. Chronic restraint stress during withdrawal increases vulnerability to drug priming-induced cocaine seeking via a dopamine D1-like receptor-mediated mechanism.

    Science.gov (United States)

    Ball, Kevin T; Stone, Eric; Best, Olivia; Collins, Tyler; Edson, Hunter; Hagan, Erin; Nardini, Salvatore; Neuciler, Phelan; Smolinsky, Michael; Tosh, Lindsay; Woodlen, Kristin

    2018-06-01

    A major obstacle in the treatment of individuals with cocaine addiction is their high propensity for relapse. Although the clinical scenario of acute stress-induced relapse has been well studied in animal models, few pre-clinical studies have investigated the role of chronic stress in relapse or the interaction between chronic stress and other relapse triggers. We tested the effect of chronic restraint stress on cocaine seeking in rats using both extinction- and abstinence-based animal relapse models. Rats were trained to press a lever for I.V. cocaine infusions (0.50 mg/kg/infusion) paired with a discrete tone + light cue in daily 3-h sessions. Following self-administration, rats were exposed to a chronic restraint stress procedure (3 h/day) or control procedure (unstressed) during the first seven days of a 13-day extinction period during which lever presses had no programmed consequences. This was followed by cue- and cocaine priming-induced drug seeking tests. In a separate group of rats, cocaine seeking was assessed during forced abstinence both before and after the same chronic stress procedure. A history of chronic restraint stress was associated with increased cocaine priming-induced drug seeking, an effect attenuated by co-administration of SCH-23390 (10.0 μg/kg; i.p.), a dopamine D 1 -like receptor antagonist, with daily restraint. Repeated SCH-23390 administration but not stress during extinction increased cue-induced reinstatement. Exposure to chronic stress during early withdrawal may confer lasting vulnerability to some types of relapse, and dopamine D 1 -like receptors appear to mediate both chronic stress effects on cocaine seeking and extinction of cocaine seeking. Copyright © 2018 Elsevier B.V. All rights reserved.

  17. Meta-analysis of the effects of cognitive-behavioral therapy on the core eating disorder maintaining mechanisms: implications for mechanisms of therapeutic change.

    Science.gov (United States)

    Linardon, Jake

    2018-03-01

    The original and enhanced cognitive model of eating disorders proposes that cognitive-behavioral therapy (CBT) "works" through modifying dietary restraint and dysfunctional attitudes towards shape and weight. However, evidence supporting the validity of this model is limited. This meta-analysis examined whether CBT can effectively modify these proposed maintaining mechanisms. Randomized controlled trials that compared CBT to control conditions or non-CBT interventions, and reported dietary restraint and shape and weight concern outcomes were searched. Twenty-nine trials were included. CBT was superior to control conditions in reducing shape (g=0.53) and weight (g=0.63) concerns, and dietary restraint (g=0.36). These effects occurred across all diagnoses and treatment formats. Improvements in shape and weight concerns and restraint were also greater in CBT than non-CBT interventions (g's=0.25, 0.24, 0.31, respectively) at post-treatment and follow-up. The magnitude of improvement in binge/purge symptoms was related to the magnitude of improvement in these maintaining mechanisms. Findings demonstrate that CBT has a specific effect in targeting the eating disorder maintaining mechanisms, and offers support to the underlying cognitive model. If changes in these variables during treatment are shown to be causal mechanisms, then these findings show that CBT, relative to non-CBT interventions, is better able to modify these mechanisms.

  18. Chronic restraint stress causes a delayed increase in responding for palatable food cues during forced abstinence via a dopamine D1-like receptor-mediated mechanism.

    Science.gov (United States)

    Ball, Kevin T; Best, Olivia; Luo, Jonathan; Miller, Leah R

    2017-02-15

    Relapse to unhealthy eating habits in dieters is often triggered by stress. Animal models, moreover, have confirmed a causal role for acute stress in relapse. The role of chronic stress in relapse vulnerability, however, has received relatively little attention. Therefore, in the present study, we used an abstinence-based relapse model in rats to test the hypothesis that exposure to chronic stress increases subsequent relapse vulnerability. Rats were trained to press a lever for highly palatable food reinforcers in daily 3-h sessions and then tested for food seeking (i.e., responding for food associated cues) both before and after an acute or chronic restraint stress procedure (3h/day×1day or 10days, respectively) or control procedure (unstressed). The second food seeking test was conducted either 1day or 7days after the last restraint. Because chronic stress causes dopamine D1-like receptor-mediated alterations in prefrontal cortex (a relapse node), we also assessed dopaminergic involvement by administering either SCH-23390 (10.0μg/kg; i.p.), a dopamine D1-like receptor antagonist, or vehicle prior to daily treatments. Results showed that chronically, but not acutely, stressed rats displayed increased food seeking 7days, but not 1day, after the last restraint. Importantly, SCH-23390 combined with chronic stress reversed this effect. These results suggest that drugs targeting D 1 -like receptors during chronic stress may help to prevent future relapse in dieters. Copyright © 2016 Elsevier B.V. All rights reserved.

  19. Crucial Physical Dependencies of the Core-Collapse Supernova Mechanism

    Science.gov (United States)

    Burrows, A.; Vartanyan, D.; Dolence, J. C.; Skinner, M. A.; Radice, D.

    2018-02-01

    We explore with self-consistent 2D F ornax simulations the dependence of the outcome of collapse on many-body corrections to neutrino-nucleon cross sections, the nucleon-nucleon bremsstrahlung rate, electron capture on heavy nuclei, pre-collapse seed perturbations, and inelastic neutrino-electron and neutrino-nucleon scattering. Importantly, proximity to criticality amplifies the role of even small changes in the neutrino-matter couplings, and such changes can together add to produce outsized effects. When close to the critical condition the cumulative result of a few small effects (including seeds) that individually have only modest consequence can convert an anemic into a robust explosion, or even a dud into a blast. Such sensitivity is not seen in one dimension and may explain the apparent heterogeneity in the outcomes of detailed simulations performed internationally. A natural conclusion is that the different groups collectively are closer to a realistic understanding of the mechanism of core-collapse supernovae than might have seemed apparent.

  20. Testing the relative associations of different components of dietary restraint on psychological functioning in anorexia nervosa and bulimia nervosa.

    Science.gov (United States)

    Linardon, Jake; Phillipou, Andrea; Newton, Richard; Fuller-Tyszkiewicz, Matthew; Jenkins, Zoe; Cistullo, Leonardo L; Castle, David

    2018-05-25

    Although empirical evidence identifies dietary restraint as a transdiagnostic eating disorder maintaining mechanism, the distinctiveness and significance of the different behavioural and cognitive components of dietary restraint are poorly understood. The present study examined the relative associations of the purportedly distinct dietary restraint components (intention to restrict, delayed eating, food avoidance, and diet rules) with measures of psychological distress (depression, anxiety, and stress), disability, and core eating disorder symptoms (overvaluation and binge eating) in patients with anorexia nervosa (AN) and bulimia nervosa (BN). Data were analysed from a treatment-seeking sample of individuals with AN (n = 124) and BN (n = 54). Intention to restrict, food avoidance, and diet rules were strongly related to each other (all r's > 0.78), but only weakly-moderately related to delayed eating behaviours (all r's psychological distress. Patient diagnosis did not moderate these associations. Overall, findings indicate that delayed eating behaviours may be a distinct component from other indices of dietary restraint (e.g., intention to restrict, food avoidance, diet rules). This study highlights the potential importance of ensuring that delayed eating behaviours are screened, assessed, and targeted early in treatment for patients with AN and BN. Copyright © 2018 Elsevier Ltd. All rights reserved.

  1. Status of voluntary restraint

    Energy Technology Data Exchange (ETDEWEB)

    Aarts, W. [SWOKA Institute for Strategic Consumer Behaviour, Leiden (Netherlands)

    2000-05-01

    Do people enjoying a higher status, especially those with a higher education, constrain their consumption more than others? In general, higher status and high levels of consumption go hand in hand. But the greater availability of luxury goods has led to a decline in their exclusivity. Since environmental awareness has increased, a countercurrent may be possible. It is possible that certain high status groups, the environmentally aware trendsetters, can now be distinguished by their voluntary restraint rather than by their conspicuous consumption. This hypothesis formed the basis for a sociological doctoral project at the University of Amsterdam. The research was conducted under the umbrella of the National Research Programme on Global Air Pollution and Climate Change.

  2. Tidal excitation of elliptical instability in the Martian core: Possible mechanism for generating the core dynamo

    Science.gov (United States)

    Arkani-Hamed, J.; Seyed-Mahmoud, B.; Aldridge, K. D.; Baker, R. E.

    2008-06-01

    We propose a causal relationship between the creation of the giant impact basins on Mars by a large asteroid, ruptured when it entered the Roche limit, and the excitation of the Martian core dynamo. Our laboratory experiments indicate that the elliptical instability of the Martian core can be excited if the asteroid continually exerts tidal forces on Mars for ~20,000 years. Our numerical experiments suggest that the growth-time of the instability was 5,000-15,000 years when the asteroid was at a distance of 50,000-75,000 km. We demonstrate the stability of the orbital motion of an asteroid captured by Mars at a distance of 100,000 km in the presence of the Sun and Jupiter. We also present our results for the tidal interaction of the asteroid with Mars. An asteroid captured by Mars in prograde fashion can survive and excite the elliptical instability of the core for only a few million years, whereas a captured retrograde asteroid can excite the elliptical instability for hundreds of millions of years before colliding with Mars. The rate at which tidal energy dissipates in Mars during this period is over two orders of magnitude greater than the rate at which magnetic energy dissipates. If only 1% of the tidal energy dissipation is partitioned to the core, sufficient energy would be available to maintain the core dynamo. Accordingly, a retrograde asteroid is quite capable of exciting an elliptical instability in the Martian core, thus providing a candidate process to drive a core dynamo.

  3. 32 CFR 636.34 - Restraint systems.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Restraint systems. 636.34 Section 636.34 National... Restraint systems. (a) Restraint systems (seat belts) will be worn by all operators and passengers of U.S. Government vehicles on or off the installations. (b) Restraint systems will be worn by all civilian personnel...

  4. Finite element program ARKAS: verification for IAEA benchmark problem analysis on core-wide mechanical analysis of LMFBR cores

    International Nuclear Information System (INIS)

    Nakagawa, M.; Tsuboi, Y.

    1990-01-01

    ''ARKAS'' code verification, with the problems set in the International Working Group on Fast Reactors (IWGFR) Coordinated Research Programme (CRP) on the inter-comparison between liquid metal cooled fast breeder reactor (LMFBR) Core Mechanics Codes, is discussed. The CRP was co-ordinated by the IWGFR around problems set by Dr. R.G. Anderson (UKAEA) and arose from the IWGFR specialists' meeting on The Predictions and Experience of Core Distortion Behaviour (ref. 2). The problems for the verification (''code against code'') and validation (''code against experiment'') were set and calculated by eleven core mechanics codes from nine countries. All the problems have been completed and were solved with the core structural mechanics code ARKAS. Predictions by ARKAS agreed very well with other solutions for the well-defined verification problems. For the validation problems based on Japanese ex-reactor 2-D thermo-elastic experiments, the agreements between measured and calculated values were fairly good. This paper briefly describes the numerical model of the ARKAS code, and discusses some typical results. (author)

  5. Core compressor exit stage study. 1: Aerodynamic and mechanical design

    Science.gov (United States)

    Burdsall, E. A.; Canal, E., Jr.; Lyons, K. A.

    1979-01-01

    The effect of aspect ratio on the performance of core compressor exit stages was demonstrated using two three stage, highly loaded, core compressors. Aspect ratio was identified as having a strong influence on compressors endwall loss. Both compressors simulated the last three stages of an advanced eight stage core compressor and were designed with the same 0.915 hub/tip ratio, 4.30 kg/sec (9.47 1bm/sec) inlet corrected flow, and 167 m/sec (547 ft/sec) corrected mean wheel speed. The first compressor had an aspect ratio of 0.81 and an overall pressure ratio of 1.357 at a design adiabatic efficiency of 88.3% with an average diffusion factor or 0.529. The aspect ratio of the second compressor was 1.22 with an overall pressure ratio of 1.324 at a design adiabatic efficiency of 88.7% with an average diffusion factor of 0.491.

  6. Evaluation of the influence of bypass flow gap distribution on the core hot spot in a prismatic VHTR core

    International Nuclear Information System (INIS)

    Kim, Min-Hwan; Lim, Hong-Sik

    2011-01-01

    Highlights: → A procedure to evaluate the local gap size variation between graphite blocks was developed and applied to a prismatic core VHTR. → The analysis for the core bypass flow and hot spot was carried out based on the calculated gap distributions. → The predicted gap size is large enough to affect the flow distribution in the core. → The bypass gap and flow distributions are closely related to the local hot spot temperature and its location. → The core restraint mechanism preventing outward movement of graphite block reduces the bypass gap size and hot spot temperature. - Abstract: Core bypass flow in VHTR is one of the key issues for core thermal margins and efficiency. The bypass flow in the prismatic core varies during core cycles due to the irradiation shrinkage/swelling and thermal expansion of the graphite blocks. A procedure to evaluate the local gap size variation between graphite blocks was developed and applied to a prismatic core VHTR. The influence of the core restraint mechanism on the bypass flow gap was evaluated. The predicted gap size is as much as 8 mm when the graphite block is exposed to its allowable limit of fast neutron fluence. The analysis for the core bypass flow and hot spot was carried out based on the calculated gap distributions. The results indicate that the bypass gap and flow distributions are closely related to the local hot spot and its location and the core restraint mechanism preventing outward movement of the graphite block by a fastening device reduces the bypass gap size, which results in the decrease of maximum fuel temperature not less than 100 deg. C, when compared to the case without it.

  7. Mechanical properties of zirconia core-shell rods with porous core and dense shell prepared by thermoplastic co-extrusion

    Czech Academy of Sciences Publication Activity Database

    Kaštyl, J.; Chlup, Zdeněk; Clemen, F.; Trunec, M.

    2017-01-01

    Roč. 37, č. 6 (2017), s. 2439-2447 ISSN 0955-2219 R&D Projects: GA MŠk(CZ) LQ1601 Institutional support: RVO:68081723 Keywords : ceramic injection moldings * oxide fuel -cells * electrophoretic deposition * large pores * alumina * fabrication * behavior * tubes * bioceramics * composites * Zirconia * Co-extrusion * Core-shell * Porous structure * Mechanical properties Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass OBOR OECD: Ceramics Impact factor: 3.411, year: 2016

  8. An overview of the Indian program related to fast reactor core mechanical behaviour

    International Nuclear Information System (INIS)

    Govindarajan, S.; Bhoje, S.B.; Paranjpe, S.R.

    1984-01-01

    This Indian review paper presents the evolution of the fast breeder program which began with fast breeder test reactor (FBTR) commencing in 1972. The state-of-art in the field of core mechanical behaviour is reviewed

  9. Mechanical design of core components for a high performance light water reactor with a three pass core

    International Nuclear Information System (INIS)

    Fischer, Kai; Schneider, Tobias; Redon, Thomas; Schulenberg, Thomas; Starflinger, Joerg

    2007-01-01

    Nuclear reactors using supercritical water as coolant can achieve more than 500 deg. C core outlet temperature, if the coolant is heated up in three steps with intermediate mixing to avoid hot streaks. This method reduces the peak cladding temperatures significantly compared with a single heat up. The paper presents an innovative mechanical design which has been developed recently for such a High Performance Light Water Reactor. The core is built with square assemblies of 40 fuel pins each, using wire wraps as grid spacers. Nine of these assemblies are combined to a cluster having a common head piece and a common foot piece. A downward flow of additional moderator water, separated from the coolant, is provided in gaps between the assemblies and in a water box inside each assembly. The cluster head and foot pieces and mixing chambers, which are key components for this design, are explained in detail. (authors)

  10. CETA truck and EVA restraint system

    Science.gov (United States)

    Beals, David C.; Merson, Wayne R.

    1991-01-01

    The Crew Equipment Translation Aid (CETA) experiment is an extravehicular activity (EVA) Space Transportation System (STS) based flight experiment which will explore various modes of transporting astronauts and light equipment for Space Station Freedom (SSF). The basic elements of CETA are: (1) two 25 foot long sections of monorail, which will be EVA assembled in the STS cargo bay to become a single 50 ft. rail called the track; (2) a wheeled baseplate called the truck which rolls along the track and can accept three cart concepts; and (3) the three carts which are designated manual, electric, and mechanical. The three carts serve as the astronaut restraint and locomotive interfaces with the track. The manual cart is powered by the astronaut grasping the track's handrail and pulling himself along. The electric cart is operated by an astronaut turning a generator which powers the electric motor and drives the cart. The mechanical cart is driven by a Bendix type transmission and is similar in concept to a man-propelled railroad cart. During launch and landing, the truck is attached to the deployable track by means of EVA removable restraint bolts and held in position by a system of retractable shims. These shims are positioned on the exterior of the rail for launch and landing and rotate out of the way for the duration of the experiment. The shims are held in position by strips of Velcro nap, which rub against the sides of the shim and exert a tailored force. The amount of force required to rotate the shims was a major EVA concern, along with operational repeatability and extreme temperature effects. The restraint system was tested in a thermal-vac and vibration environment and was shown to meet all of the initial design requirements. Using design inputs from the astronauts who will perform the EVA, CETA evolved through an iterative design process and represented a cooperative effort.

  11. Experimental Study and Mathematical Modeling of Asphaltene Deposition Mechanism in Core Samples

    Directory of Open Access Journals (Sweden)

    Jafari Behbahani T.

    2015-11-01

    Full Text Available In this work, experimental studies were conducted to determine the effect of asphaltene deposition on the permeability reduction and porosity reduction of carbonate, sandstone and dolomite rock samples using an Iranian bottom hole live oil sample which is close to reservoir conditions, whereas in the majority of previous work, a mixture of recombined oil (a mixture of dead oil and associated gas was injected into a core sample which is far from reservoir conditions. The effect of the oil injection rate on asphaltene deposition and permeability reduction was studied. The experimental results showed that an increase in the oil injection flow rate can result in an increase in asphaltene deposition and permeability reduction. Also, it can be observed that at lower injection flow rates, a monotonic decrease in permeability of the rock samples can be attained upon increasing the injection flow rate, while at higher injection rates, after a decrease in rock permeability, an increasing trend is observed before a steady-state condition can be reached. The experimental results also showed that the rock type can affect the amount of asphaltene deposition, and the asphaltene deposition has different mechanisms in sandstone and carbonate core samples. It can be seen that the adsorption and plugging mechanisms have a more important role in asphaltene deposition in carbonate core samples than sandstone core samples. From the results, it can be observed that the pore volumes of the injected crude oil are higher for sandstone cores compared with the carbonate cores. Also, it can be inferred that three depositional types may take place during the crude oil injection, i.e., continuous deposition for low-permeability cores, slow, steady plugging for high-permeability cores and steady deposition for medium-permeability cores. It can be seen from the experimental results that damage to the core samples was found to increase when the production pressures were

  12. Mechanical and thermo-mechanical response of a lead-core bearing device subjected to different loading conditions

    Directory of Open Access Journals (Sweden)

    Zhelyazov Todor

    2018-01-01

    Full Text Available The contribution is focused on the numerical modelling, simulation and analysis of a lead-core bearing device for passive seismic isolation. An accurate finite element model of a lead-core bearing device is presented. The model is designed to analyse both mechanical and thermo-mechanical responses of the seismic isolator to different loading conditions. Specifically, the mechanical behaviour in a typical identification test is simulated. The response of the lead-core bearing device to circular sinusoidal paths is analysed. The obtained shear displacement – shear force relationship is compared to experimental data found in literature sources. The hypothesis that heating of the lead-core during cyclic loading affects the degrading phenomena in the bearing device is taken into account. Constitutive laws are defined for each material: lead, rubber and steel. Both predefined constitutive laws (in the used general–purpose finite element code and semi-analytical procedures aimed at a more accurate modelling of the constitutive relations are tested. The results obtained by finite element analysis are to be further used to calibrate a macroscopic model of the lead-core bearing device seen as a single-degree-of-freedom mechanical system.

  13. A week of Israeli restraint

    NARCIS (Netherlands)

    Reinhart, T.

    2006-01-01

    In Israeli discourse, Israel is always the side exercising restraint in its conflict with the Palestinians. This was true again for the events of the past week: As the Qassam rockets were falling on the Southern Israeli town of Sderot, it was “leaked” that the Israeli Minister of Defense had

  14. Development and testing of restraints for nuclear piping systems

    International Nuclear Information System (INIS)

    Kelly, J.M.; Skinner, M.S.

    1980-06-01

    As an alternative to current practice of pipe restraint within nuclear power plants it has been proposed to adopt restraints capable of dissipating energy in the piping system. The specific mode of energy dissipation focused upon in these studies is the plastic yielding of steels utilizing relative movement between the pipe and the base of the restraint, a general mechanism which has been proven as reliable in several allied studies. This report discusses the testing of examples of two energy-absorbing devices, the results of this testing and the conclusions drawn. This study concentrated on the specific relevant performance characteristics of hysteretic behavior and degradation with use. The testing consisted of repetitive continuous loadings well into the plastic ranges of the devices in a sinusoidal or random displacement controlled mode

  15. Simple Synthesis and Growth Mechanism of Core/Shell CdSe/SiOx Nanowires

    Directory of Open Access Journals (Sweden)

    Guozhang Dai

    2010-01-01

    Full Text Available Core-shell-structured CdSe/SiOx nanowires were synthesized on an equilateral triangle Si (111 substrate through a simple one-step thermal evaporation process. SEM, TEM, and XRD investigations confirmed the core-shell structure; that is, the core zone is single crystalline CdSe and the shell zone is SiOx amorphous layer and CdSe core was grown along (001 direction. Two-stage growth process was present to explain the growth mechanism of the core/shell nanwires. The silicon substrate of designed equilateral triangle providing the silicon source is the key factor to form the core-shell nanowires, which is significant for fabrication of nanowire-core sheathed with a silica system. The PL of the product studied at room temperature showed two emission bands around 715 and 560 nm, which originate from the band-band transition of CdSe cores and the amorphous SiOx shells, respectively.

  16. Design and optimization for the occupant restraint system of vehicle based on a single freedom model

    Science.gov (United States)

    Zhang, Junyuan; Ma, Yue; Chen, Chao; Zhang, Yan

    2013-05-01

    Throughout the vehicle crash event, the interactions between vehicle, occupant, restraint system (VOR) are complicated and highly non-linear. CAE and physical tests are the most widely used in vehicle passive safety development, but they can only be done with the detailed 3D model or physical samples. Often some design errors and imperfections are difficult to correct at that time, and a large amount of time will be needed. A restraint system concept design approach which based on single-degree-of-freedom occupant-vehicle model (SDOF) is proposed in this paper. The interactions between the restraint system parameters and the occupant responses in a crash are studied from the view of mechanics and energy. The discrete input and the iterative algorithm method are applied to the SDOF model to get the occupant responses quickly for arbitrary excitations (impact pulse) by MATLAB. By studying the relationships between the ridedown efficiency, the restraint stiffness, and the occupant response, the design principle of the restraint stiffness aiming to reduce occupant injury level during conceptual design is represented. Higher ridedown efficiency means more occupant energy absorbed by the vehicle, but the research result shows that higher ridedown efficiency does not mean lower occupant injury level. A proper restraint system design principle depends on two aspects. On one hand, the restraint system should lead to as high ridedown efficiency as possible, and at the same time, the restraint system should maximize use of the survival space to reduce the occupant deceleration level. As an example, an optimization of a passenger vehicle restraint system is designed by the concept design method above, and the final results are validated by MADYMO, which is the most widely used software in restraint system design, and the sled test. Consequently, a guideline and method for the occupant restraint system concept design is established in this paper.

  17. Bioprinting Using Mechanically Robust Core-Shell Cell-Laden Hydrogel Strands.

    Science.gov (United States)

    Mistry, Pritesh; Aied, Ahmed; Alexander, Morgan; Shakesheff, Kevin; Bennett, Andrew; Yang, Jing

    2017-06-01

    The strand material in extrusion-based bioprinting determines the microenvironments of the embedded cells and the initial mechanical properties of the constructs. One unmet challenge is the combination of optimal biological and mechanical properties in bioprinted constructs. Here, a novel bioprinting method that utilizes core-shell cell-laden strands with a mechanically robust shell and an extracellular matrix-like core has been developed. Cells encapsulated in the strands demonstrate high cell viability and tissue-like functions during cultivation. This process of bioprinting using core-shell strands with optimal biochemical and biomechanical properties represents a new strategy for fabricating functional human tissues and organs. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Mechanical properties of kenaf bast and core fibre reinforced unsaturated polyester composites

    Energy Technology Data Exchange (ETDEWEB)

    Ishak, M R; Leman, Z; Sapuan, S M [Department of Mechanical and Manufacturing Engineering, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Edeerozey, A M M; Othman, I S, E-mail: zleman@eng.upm.edu.my [Faculty of Manufacturing Engineering, Universiti Teknikal Malaysia Melaka, 76109 Durian Tunggal, Melaka (Malaysia)

    2010-05-15

    Kenaf fibre has high potential to be used for composite reinforcement in biocomposite material. It is made up of an inner woody core and an outer fibrous bark surrounding the core. The aim of this study was to compare the mechanical properties of short kenaf bast and core fibre reinforced unsaturated polyester composites with varying fibre weight fraction i.e. 0%, 5%, 10%, 20%, 30% and 40%. The compression moulding technique was used to prepare the composite specimens for tensile, flexural and impact tests in accordance to the ASTM D5083, ASTM D790 and ASTM D256 respectively. The overall results showed that the composites reinforced with kenaf bast fibre had higher mechanical properties than kenaf core fibre composites. The results also showed that the optimum fibre content for achieving highest tensile strength for both bast and core fibre composites was 20%wt. It was also observed that the elongation at break for both composites decreased as the fibre content increased. For the flexural strength, the optimum fibre content for both composites was 10%wt while for impact strength, it was at 10%wt and 5%wt for bast and core fibre composites respectively.

  19. Mechanical properties of kenaf bast and core fibre reinforced unsaturated polyester composites

    International Nuclear Information System (INIS)

    Ishak, M R; Leman, Z; Sapuan, S M; Edeerozey, A M M; Othman, I S

    2010-01-01

    Kenaf fibre has high potential to be used for composite reinforcement in biocomposite material. It is made up of an inner woody core and an outer fibrous bark surrounding the core. The aim of this study was to compare the mechanical properties of short kenaf bast and core fibre reinforced unsaturated polyester composites with varying fibre weight fraction i.e. 0%, 5%, 10%, 20%, 30% and 40%. The compression moulding technique was used to prepare the composite specimens for tensile, flexural and impact tests in accordance to the ASTM D5083, ASTM D790 and ASTM D256 respectively. The overall results showed that the composites reinforced with kenaf bast fibre had higher mechanical properties than kenaf core fibre composites. The results also showed that the optimum fibre content for achieving highest tensile strength for both bast and core fibre composites was 20%wt. It was also observed that the elongation at break for both composites decreased as the fibre content increased. For the flexural strength, the optimum fibre content for both composites was 10%wt while for impact strength, it was at 10%wt and 5%wt for bast and core fibre composites respectively.

  20. Nuclear component horizontal seismic restraint

    International Nuclear Information System (INIS)

    Snyder, G.J.

    1988-01-01

    In a nuclear reactor having a reactor vessel, a reactor guard vessel, a thermal insulation shell and a horizontal seismic restraint, a restraint is described comprising: a. a first ring on the wall of the reactor vessel; b. a second ring on the wall of the reactor guard vessel in alignment with the first ring; c. a first block attached to the second ring proximate the first ring so as to provide a predetermined clearance between the first block and the first ring which is reduced to zero during thermal expansion; d. motion limit means extending through an aperture in the thermal insulation shell in alignment with the second ring and the first block; the e. a second block attached to the motion limit means proximate the second ring and in alignment the first block so as to provide a predetermined clearance between the second block and the second ring which is reduced to zero during thermal expansion

  1. Humidity Effects on Soluble Core Mechanical and Thermal Properties (Polyvinyl Alcohol/Microballoon Composite)

    Science.gov (United States)

    1993-01-01

    This document constitutes the final report for the study of humidity effects and loading rate on soluble core (PVA/MB composite material) mechanical and thermal properties. This report describes test results, procedures employed, and any unusual occurrences or specific observations associated with this test program.

  2. HCV Core Protein Uses Multiple Mechanisms to Induce Oxidative Stress in Human Hepatoma Huh7 Cells

    Science.gov (United States)

    Ivanov, Alexander V.; Smirnova, Olga A.; Petrushanko, Irina Y.; Ivanova, Olga N.; Karpenko, Inna L.; Alekseeva, Ekaterina; Sominskaya, Irina; Makarov, Alexander A.; Bartosch, Birke; Kochetkov, Sergey N.; Isaguliants, Maria G.

    2015-01-01

    Hepatitis C virus (HCV) infection is accompanied by the induction of oxidative stress, mediated by several virus proteins, the most prominent being the nucleocapsid protein (HCV core). Here, using the truncated forms of HCV core, we have delineated several mechanisms by which it induces the oxidative stress. The N-terminal 36 amino acids of HCV core induced TGFβ1-dependent expression of nicotinamide adenine dinucleotide phosphate (NADPH) oxidases 1 and 4, both of which independently contributed to the production of reactive oxygen species (ROS). The same fragment also induced the expression of cyclo-oxygenase 2, which, however, made no input into ROS production. Amino acids 37–191 of HCV core up-regulated the transcription of a ROS generating enzyme cytochrome P450 2E1. Furthermore, the same fragment induced the expression of endoplasmic reticulum oxidoreductin 1α. The latter triggered efflux of Ca2+ from ER to mitochondria via mitochondrial Ca2+ uniporter, leading to generation of superoxide anions, and possibly also H2O2. Suppression of any of these pathways in cells expressing the full-length core protein led to a partial inhibition of ROS production. Thus, HCV core causes oxidative stress via several independent pathways, each mediated by a distinct region of the protein. PMID:26035647

  3. Beacon: A three-dimensional structural analysis code for bowing history of fast breeder reactor cores

    International Nuclear Information System (INIS)

    Miki, K.

    1979-01-01

    The core elements of an LMFBR are bowed due to radial gradients of both temperature and neutron flux in the core. Since all hexagonal elements are multiply supported by adjacent elements or the restraint system, restraint forces and bending stresses are induced. In turn, these forces and stresses are relaxed by irradiation enhanced creep of the material. The analysis of the core bowing behavior requires a three-dimensional consideration of the mechanical interactions among the core elements, because the core consists of different kinds of elements and of fuel assemblies with various burnup histories. A new computational code BEACON has been developed for analyzing the bowing behavior of an LMFBR's core in three dimensions. To evaluate mechanical interactions among core elements, the code uses the analytical method of the earlier SHADOW code. BEACON analyzes the mechanical interactions in three directions, which form angles of 60 0 with one another. BEACON is applied to the 60 0 sector of a typical LMFBR's core for analyzing the bowing history during one equilibrium cycle. 120 core elements are treated, assuming the boundary condition of rotational symmetry. The application confirms that the code can be an effective tool for parametric studies as well as for detailed structural analysis of LMFBR's core. (orig.)

  4. Predictors of restraint use among child occupants.

    Science.gov (United States)

    Benedetti, Marco; Klinich, Kathleen D; Manary, Miriam A; Flannagan, Carol A

    2017-11-17

    The objective of this study was to identify factors that predict restraint use and optimal restraint use among children aged 0 to 13 years. The data set is a national sample of police-reported crashes for years 2010-2014 in which type of child restraint is recorded. The data set was supplemented with demographic census data linked by driver ZIP code, as well as a score for the state child restraint law during the year of the crash relative to best practice recommendations for protecting child occupants. Analysis used linear regression techniques. The main predictor of unrestrained child occupants was the presence of an unrestrained driver. Among restrained children, children had 1.66 (95% confidence interval, 1.27, 2.17) times higher odds of using the recommended type of restraint system if the state law at the time of the crash included requirements based on best practice recommendations. Children are more likely to ride in the recommended type of child restraint when their state's child restraint law includes wording that follows best practice recommendations for child occupant protection. However, state child restraint law requirements do not influence when caregivers fail to use an occupant restraint for their child passengers.

  5. Metabolic immune restraints: implications for anticancer vaccines.

    Science.gov (United States)

    Mocellin, Simone

    2010-01-01

    Metabolic immune restraints belong to a highly complex network of molecular mechanisms underlying the failure of naturally occurring and therapeutically induced immune responses against cancer. In the light of the disappointing results yielded so far with anticancer vaccines in the clinical setting, the dissection of the cascade of molecular events leading to tumor immune escape appears the most promising way to develop more effective immunotherapeutic strategies. Here we review the significant advances recently made in the understanding of the tumor-specific metabolic features that contribute to keep malignant cells from being recognized and destroyed by immune effectors. These mechanistic insights are fostering the development of rationally designed therapeutics aimed to revert the immunosuppressive circuits and thus to enhance the effectiveness of anticancer vaccines.

  6. Numerical and Experimental Investigations on Mechanical Behavior of Composite Corrugated Core

    Science.gov (United States)

    Dayyani, Iman; Ziaei-Rad, Saeed; Salehi, Hamid

    2012-06-01

    Tensile and flexural characteristics of corrugated laminate panels were studied using numerical and analytical methods and compared with experimental data. Prepreg laminates of glass fiber plain woven cloth were hand-laid by use of a heat gun to ease the creation of the panel. The corrugated panels were then manufactured by using a trapezoidal machined aluminium mould. First, a series of simple tension tests were performed on standard samples to evaluate the material characteristics. Next, the corrugated panels were subjected to tensile and three-point bending tests. The force-displacement graphs were recorded. Numerical and analytical solutions were proposed to simulate the mechanical behavior of the panels. In order to model the energy dissipation due to delamination phenomenon observed in tensile tests in all members of corrugated core, plastic behavior was assigned to the whole geometry, not only to the corner regions. Contrary to the literature, it is shown that the three-stage mechanical behavior of composite corrugated core is not confined to aramid reinforced corrugated laminates and can be observed in other types such as fiber glass. The results reveal that the mechanical behavior of the core in tension is sensitive to the variation of core height. In addition, for the first time, the behavior of composite corrugated core was studied and verified in bending. Finally, the analytical and numerical results were validated by comparing them with experimental data. A good degree of correlation was observed which showed the suitability of the finite element model for predicting the mechanical behavior of corrugated laminate panels.

  7. Design and intestinal mucus penetration mechanism of core-shell nanocomplex.

    Science.gov (United States)

    Zhang, Xin; Cheng, Hongbo; Dong, Wei; Zhang, Meixia; Liu, Qiaoyu; Wang, Xiuhua; Guan, Jian; Wu, Haiyang; Mao, Shirui

    2018-02-28

    The objective of this study was to design intestinal mucus-penetrating core-shell nanocomplex by functionally mimicking the surface of virus, which can be used as the carrier for peroral delivery of macromolecules, and further understand the influence of nanocomplex surface properties on the mucosal permeation capacity. Taking insulin as a model drug, the core was formed by the self-assembly among positively charged chitosan, insulin and negatively charged sodium tripolyphosphate, different types of alginates were used as the shell forming material. The nanocomplex was characterized by dynamic light scattering (DLS), atomic force microscopy (AFM) and FTIR. Nanocomplex movement in mucus was recorded using multiple particle tracking (MPT) method. Permeation and uptake of different nanocomplex were studied in rat intestine. It was demonstrated that alginate coating layer was successfully formed on the core and the core-shell nanocomplex showed a good physical stability and improved enzymatic degradation protection. The mucus penetration and MPT study showed that the mucus penetration capacity of the nanocomplex was surface charge and coating polymer structure dependent, nanocomplex with negative alginate coating had 1.6-2.5 times higher mucus penetration ability than that of positively charged chitosan-insulin nanocomplex. Moreover, the mucus penetration ability of the core-shell nanocomplex was alginate structure dependent, whereas alginate with lower G content and lower molecular weight showed the best permeation enhancing ability. The improvement of intestine permeation and intestinal villi uptake of the core-shell nanocomplex were further confirmed in rat intestine and multiple uptake mechanisms were involved in the transport process. In conclusion, core-shell nanocomplex composed of oppositely charged materials could provide a strategy to overcome the mucus barrier and enhance the mucosal permeability. Copyright © 2018 Elsevier B.V. All rights reserved.

  8. Comparative study of mechanical properties of direct core build-up materials

    Directory of Open Access Journals (Sweden)

    Girish Kumar

    2015-01-01

    Full Text Available Background and Objectives: The strength greatly influences the selection of core material because core must withstand forces due to mastication and para-function for many years. This study was conducted to evaluate certain mechanical properties of commonly used materials for direct core build-up, including visible light cured composite, polyacid modified composite, resin modified glass ionomer, high copper amalgam, and silver cermet cement. Materials and Methods: All the materials were manipulated according to the manufacturer′s recommendations and standard test specimens were prepared. A universal testing machine at different cross-head speed was used to determine all the four mechanical properties. Mean compressive strength, diametral tensile strength, flexural strength, and elastic modulus with standard deviations were calculated. Multiple comparisons of the materials were also done. Results: Considerable differences in compressive strength, diametral tensile strength, and flexural strength were observed. Visible light cured composite showed relatively high compressive strength, diametral tensile strength, and flexural strength compared with the other tested materials. Amalgam showed the highest value for elastic modulus. Silver cermet showed less value for all the properties except for elastic modulus. Conclusions: Strength is one of the most important criteria for selection of a core material. Stronger materials better resist deformation and fracture provide more equitable stress distribution, greater stability, and greater probability of clinical success.

  9. Numerical and experimental investigation on labyrinth seal mechanism for bypass flow reduction in prismatic VHTR core

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Su-Jong, E-mail: paper80@snu.ac.r [Department of Nuclear Engineering, Seoul National University, San 56-1, Daehak-Dong, Kwanak-Gu, Seoul 151-742 (Korea, Republic of); Lee, Jeong-Hun [Department of Nuclear Engineering, Seoul National University, San 56-1, Daehak-Dong, Kwanak-Gu, Seoul 151-742 (Korea, Republic of); Lee, Sang-Moon [Department of Mechanical Engineering, Inha University, 253 Yonghyun-Dong, Nam-Gu, Incheon 402-751 (Korea, Republic of); Tak, Nam-il; Kim, Min-Hwan [Korea Atomic Energy Research Institute, 150-1 Deokjin-Dong, 1045 Daedeokdaero, Yuseong, Daejeon 305-353 (Korea, Republic of); Kim, Kwang-Yong [Department of Mechanical Engineering, Inha University, 253 Yonghyun-Dong, Nam-Gu, Incheon 402-751 (Korea, Republic of); Park, Goon-Cherl [Department of Nuclear Engineering, Seoul National University, San 56-1, Daehak-Dong, Kwanak-Gu, Seoul 151-742 (Korea, Republic of)

    2013-09-15

    Highlights: • Bypass flow reduction method was developed by applying labyrinth seal mechanism. • Grooves on side walls of replaceable reflector block were made. • Design of the grooved wall of the reflector block was optimized by the RSA method. • The flow resistance of the bypass gap rose from 18.04 to 26.24 by the optimization. • The bypass ratios at the inlet and outlet were reduced by 36.19% and 14.66%, respectively. -- Abstract: Core bypass flow in block type very high temperature reactor (VHTR) occurs due to the inevitable gaps between the hexagonal core blocks for the block installation and refueling. Since the core bypass flow affects the reactor safety and efficiency, it should be minimized to enhance the core thermal margin. In this regard, the core bypass flow reduction method applying the labyrinth seal mechanism was developed and optimized by using the single-objective shape optimization method. Response surface approximation (RSA) method was adopted as the optimization method. Side wall of the replaceable reflector block was redesigned and response surface approximate model was adopted to optimize the shape of the reflector wall. Computational fluid dynamics (CFD) analyses were carried out not only to assess the limitation of existing method of bypass flow reduction, but also to optimize the design of a newly developed reduction method. The experiment with Seoul National University (SNU) multi-block experimental facility was performed to demonstrate the performance of the reduction method. It was found that the effect of the existing bypass flow reduction method by sealing the bypass gap exit was restricted nearby the lower region of the core. However, the flow resistance factor of the bypass gap increased from 18.04 to 26.24 by the optimized reduction method. The results of the performance test showed that the bypass flow distribution was reduced throughout the entire core regions. The bypass flow ratios at the inlet and the outlet were

  10. Cholinergic Modulation of Restraint Stress Induced Neurobehavioral ...

    African Journals Online (AJOL)

    The involvement of the cholinergic system in restraint stress induced neurobehavioral alterations was investigated in rodents using the hole board, elevated plus maze, the open field and the light and dark box tests. Restraint stress (3h) reduced significantly (p<0.05) the number of entries and time spent in the open arm, ...

  11. Modelling mechanical properties of the multilayer composite materials with the polyamide core

    Directory of Open Access Journals (Sweden)

    Talaśka Krzysztof

    2018-01-01

    Full Text Available Due to the wide range of application for belt conveyors, engineers look for many different combinations of mechanical properties of conveyor and transmission belts. It can be made by creating multilayer or fibre reinforced composite materials from base thermoplastic or thermosetting polymers. In order to gain high strength with proper elasticity and friction coefficient, the core of the composite conveyor belt is made of polyamide film core, which can be combined with various types of polymer fabrics, films or even rubbers. In this paper authors show the complex model of multilayer composite belt with the polyamide core, which can be used in simulation analyses. The following model was derived based on the experimental research, which consisted of tensile, compression and shearing tests. In order to achieve the most accurate model, proper simulations in ABAQUS were made and then the results were compared with empirical mechanical characteristics of a conveyor belt. The main goal of this research is to fully describe the perforation process of conveyor and transmission belts for vacuum belt conveyors. The following model will help to develop design briefs for machines used for mechanical perforation.

  12. 3D FDM production and mechanical behavior of polymeric sandwich specimens embedding classical and honeycomb cores

    Science.gov (United States)

    Brischetto, Salvatore; Ferro, Carlo Giovanni; Torre, Roberto; Maggiore, Paolo

    2018-04-01

    Desktop 3D FDM (Fused Deposition Modelling) printers are usually employed for the production of nonstructural objects. In recent years, the present authors tried to use this technology also to produce structural elements employed in the construction of small UAVs (Unmanned Aerial Vehicles). Mechanical stresses are not excessive for small multirotor UAVs. Therefore, the FDM technique combined with polymers, such as the ABS (Acrylonitrile Butadiene Styrene) and the PLA(Poly Lactic Acid), can be successfully employed to produce structural components. The present new work is devoted to the production and preliminary structural analysis of sandwich configurations. These new lamination schemes could lead to an important weight reduction without significant decreases of mechanical properties. Therefore, it could be possible, for the designed application (e.g., a multifunctional small UAV produced via FDM), to have stiffener and lighter structures easy to be manufactured with a low-cost 3D printer. The new sandwich specimens here proposed are PLA sandwich specimens embedding a PLA honeycomb core produced by means of the same extruder, multilayered specimens with ABS external layers and an internal homogeneous PLA core using different extruders for the two materials, sandwich specimens with external ABS skins and an internal PLA honeycomb core using different extruders for the two materials, and sandwich specimens where two different extruders have been employed for PLA material used for skins and for the internal honeycomb core. For all the proposed configurations, a detailed description of the production activity is given.Moreover, several preliminary results about three-point bending tests, different mechanical behaviors and relative delamination problems for each sandwich configuration will be discussed in depth.

  13. Neurocognitive Mechanisms Underlying Value-Based Decision-Making: From Core Values to Economic Value

    Directory of Open Access Journals (Sweden)

    Tobias eBrosch

    2013-07-01

    Full Text Available Value plays a central role in practically every aspect of human life that requires a decision: whether we choose between different consumer goods, whether we decide which person we marry or which political candidate gets our vote, we choose the option that has more value to us. Over the last decade, neuroeconomic research has mapped the neural substrates of economic value, revealing that activation in brain regions such as ventromedial prefrontal cortex (VMPFC, ventral striatum or posterior cingulate cortex reflects how much an individual values an option and which of several options he/she will choose. However, while great progress has been made exploring the mechanisms underlying concrete decisions, neuroeconomic research has been less concerned with the questions of why people value what they value, and why different people value different things. Social psychologists and sociologists have long been interested in core values, motivational constructs that are intrinsically linked to the self-schema and are used to guide actions and decisions across different situations and different time points. Core value may thus be an important determinant of individual differences in economic value computation and decision-making. Based on a review of recent neuroimaging studies investigating the neural representation of core values and their interactions with neural systems representing economic value, we outline a common framework that integrates the core value concept and neuroeconomic research on value-based decision-making.

  14. Neurocognitive mechanisms underlying value-based decision-making: from core values to economic value.

    Science.gov (United States)

    Brosch, Tobias; Sander, David

    2013-01-01

    VALUE PLAYS A CENTRAL ROLE IN PRACTICALLY EVERY ASPECT OF HUMAN LIFE THAT REQUIRES A DECISION: whether we choose between different consumer goods, whether we decide which person we marry or which political candidate gets our vote, we choose the option that has more value to us. Over the last decade, neuroeconomic research has mapped the neural substrates of economic value, revealing that activation in brain regions such as ventromedial prefrontal cortex (VMPFC), ventral striatum or posterior cingulate cortex reflects how much an individual values an option and which of several options he/she will choose. However, while great progress has been made exploring the mechanisms underlying concrete decisions, neuroeconomic research has been less concerned with the questions of why people value what they value, and why different people value different things. Social psychologists and sociologists have long been interested in core values, motivational constructs that are intrinsically linked to the self-schema and are used to guide actions and decisions across different situations and different time points. Core value may thus be an important determinant of individual differences in economic value computation and decision-making. Based on a review of recent neuroimaging studies investigating the neural representation of core values and their interactions with neural systems representing economic value, we outline a common framework that integrates the core value concept and neuroeconomic research on value-based decision-making.

  15. Neurocognitive mechanisms underlying value-based decision-making: from core values to economic value

    Science.gov (United States)

    Brosch, Tobias; Sander, David

    2013-01-01

    Value plays a central role in practically every aspect of human life that requires a decision: whether we choose between different consumer goods, whether we decide which person we marry or which political candidate gets our vote, we choose the option that has more value to us. Over the last decade, neuroeconomic research has mapped the neural substrates of economic value, revealing that activation in brain regions such as ventromedial prefrontal cortex (VMPFC), ventral striatum or posterior cingulate cortex reflects how much an individual values an option and which of several options he/she will choose. However, while great progress has been made exploring the mechanisms underlying concrete decisions, neuroeconomic research has been less concerned with the questions of why people value what they value, and why different people value different things. Social psychologists and sociologists have long been interested in core values, motivational constructs that are intrinsically linked to the self-schema and are used to guide actions and decisions across different situations and different time points. Core value may thus be an important determinant of individual differences in economic value computation and decision-making. Based on a review of recent neuroimaging studies investigating the neural representation of core values and their interactions with neural systems representing economic value, we outline a common framework that integrates the core value concept and neuroeconomic research on value-based decision-making. PMID:23898252

  16. A study on bypass flow gap distribution in a prismatic VHTR core

    International Nuclear Information System (INIS)

    Kim, M. H.; Jo, C. K.; Lim, H. S.

    2010-01-01

    Core bypass flow in VHTR is one of the key issues for core thermal margins and efficiency. The bypass flow in the prismatic core varies during core cycles due to the irradiation shrinkage and thermal expansion of the graphite blocks. A procedure to evaluate the local gap size variation between graphite blocks was developed and applied to a prismatic core VHTR. The influence of the core restraint mechanism on the bypass flow gap was evaluated. The predicted gap size is as much as 8 mm when the graphite block is exposed to its allowable limit of irradiation fluence. The analysis for the core bypass flow and hot spot was carried out based on the calculated gap distributions. The results indicate that the bypass flow and the location of core hot spots are closely related and a measure to reduce the bypass flow is necessary. (authors)

  17. [Compatibility law of Baizhi formulae and molecular mechanism of core herbal pair "Baizhi-Chuanxiong"].

    Science.gov (United States)

    Su, Jin; Tang, Shi-Huan; Guo, Fei-Fei; Li, De-Feng; Zhang, Yi; Xu, Hai-Yu; Yang, Hong-Jun

    2018-04-01

    By using the traditional Chinese medicine inheritance support system (TCMISS) in this study, the prescription rules of Baizhi formulae were analyzed and the core herbal pair "Baizhi-Chuanxiong" was obtained. Through the systemic analysis of prescription rules of "Baizhi-Chuanxiong" and combined with the pharmacology thinking of "Baizhi-Chuanxiong" in treating headache, the paper was aimed to find out the combination rules containing Baizhi andits molecular mechanisms for treating headaches, and provide the theory basis for further research and reference of Baizhi and its formula. Totally 3 887 prescriptions were included in this study, involving 2 534 Chinese herbs. With a support degree of 20% in analysis, 16 most commonly used drug combinations were screened, which were mainly used to treat 15 types of diseases. Baizhi was often used to treat headache, and the core combination "Baizhi-Chuanxiong" was also often used to treat, consistent with ancient record. A chemical database was established; then the headache and migraine disease targets were retrieved and added in the database to build up the "compounds-targets-pathways "core network of "Baizhi-Chuanxiong" by the internet-based computation platform for IP of TCM (TCM-IP). TCM-IP was then applied to study the molecular mechanism of "Baizhi-Chuanxiong" treatment of headache. The results suggested that37 chemical compounds in the core combination "Baizhi-Chuanxiong" were closely related with headache treatment by adjusting serotonin levels or applying to inflammation-related targets and energy metabolism pathways such as purine metabolism, pyruvate metabolism, fatty acid degradation, carbon metabolism and gluconeogenesis. Copyright© by the Chinese Pharmaceutical Association.

  18. A new type of sandwich panel with periodic cellular metal cores and its mechanical performances

    International Nuclear Information System (INIS)

    Lim, Chae-Hong; Jeon, Insu; Kang, Ki-Ju

    2009-01-01

    Many studies have been performed on the mechanical properties and optimization of truss PCMs (periodic cellular metals), but those on the fabrication process, which is one of key factors determining the survivability of PCMs in the market, have been relatively limited. This study introduces a new idea on the fabrication of quasi Kagome truss cored sandwich panels, which is based on the expanded-metal process. And the mechanical behavior of the sandwich panels is to be evaluated. The mechanical strengths and failure mechanisms under compression and bending load are estimated based on elementary mechanics of materials, and the optimal design is derived. Its validity is proved by comparison with the results of experiments. The results showed that the new idea is promising with respect to all three requirements, i.e., the morphology, fabrication cost, and raw materials. The simple mechanical analysis was sufficiently effective and accurate for estimating the performance and failure mode of the sandwich panels. In the experiments, sandwich panel specimens of three different designs were compared in their bending behaviors to demonstrate sensitivity of geometric parameters. Namely, although all the designs had little difference in their load capacity-per-weight, the failure mechanisms and the behaviors after a peak load were totally different.

  19. Seismic restraint means for radiation detector

    International Nuclear Information System (INIS)

    Underwood, R.H.; Todt, W.H.

    1983-01-01

    Seismic restraint means are provided for mounting an elongated, generally cylindrical nuclear radiation detector within a tubular thimble in a nuclear reactor monitor system. The restraint means permits longitudinal movement of the radiation detector into and out of the thimble. Each restraint means comprises a split clamp ring and a plurality of symmetrically spaced support arms pivotally mounted on the clamp ring. Each support arm has spring bias means and thimble contact means eg insulating rollers whereby the contact means engage the thimble with a constant predetermined force which minimizes seismic vibration action on the radiation detector. (author)

  20. Failure Predictions for VHTR Core Components using a Probabilistic Contiuum Damage Mechanics Model

    Energy Technology Data Exchange (ETDEWEB)

    Fok, Alex

    2013-10-30

    The proposed work addresses the key research need for the development of constitutive models and overall failure models for graphite and high temperature structural materials, with the long-term goal being to maximize the design life of the Next Generation Nuclear Plant (NGNP). To this end, the capability of a Continuum Damage Mechanics (CDM) model, which has been used successfully for modeling fracture of virgin graphite, will be extended as a predictive and design tool for the core components of the very high- temperature reactor (VHTR). Specifically, irradiation and environmental effects pertinent to the VHTR will be incorporated into the model to allow fracture of graphite and ceramic components under in-reactor conditions to be modeled explicitly using the finite element method. The model uses a combined stress-based and fracture mechanics-based failure criterion, so it can simulate both the initiation and propagation of cracks. Modern imaging techniques, such as x-ray computed tomography and digital image correlation, will be used during material testing to help define the baseline material damage parameters. Monte Carlo analysis will be performed to address inherent variations in material properties, the aim being to reduce the arbitrariness and uncertainties associated with the current statistical approach. The results can potentially contribute to the current development of American Society of Mechanical Engineers (ASME) codes for the design and construction of VHTR core components.

  1. Synthesis and Growth Mechanism of Multimetallic Core-Shell and Hollow-Like Nanoparticles

    Science.gov (United States)

    Londono-Calderon, Alejandra

    A thorough control of nanoscale systems is crucial for developing and improving their activity in a variety of application fields. These range from nanocatalysis, plasmonics, nanosensors, nanomedicine, communications, and others. Controlling and understanding the growth and spatial distribution of multi metallic systems allow us to explore the correlation between the characteristics of the nanoparticle (composition, surface chemistry, crystallinity, etc.) and their properties (mechanical, optical, structural, etc.). In this dissertation bimetallic and multi-metallic nanoparticles were obtained by a seed mediated method and galvanic replacement. Combinations of the type core shell of Au Ag, Au Pd and Au Pd-Au Au multi-metallic systems were studied. A galvanic replacement method was used to obtain hollow-like Au/Pt nanoboxes and Au AgM (M = Au, Pd or Pt) yolk-shell structures with voids in the middle shell. Characterization regarding composition, morphology, optical properties and atomic structures was performed. The mechanical properties of Au Pd nanocubes were studied in situ by the use of a TEM-AFM nanomechanical holder. The nanoparticles strengthening mechanism relies on the Au core resistance to the motion of partial dislocations. The catalytic efficiency of core-shell and nanorattles structures were tested with a model reaction for the decomposition of 4-ntp to 4-amp. Yolk-shell systems exhibit an enhancement in the catalytic decomposition rate in comparison with solid and bimetallic system. Finally, the development of an Electrospray assisted Langmuir Blodgett technique was successfully employed for the deposition of nanoparticles monolayer on a substrate. High particle density and coverage of the substrate makes this a promising technique to finely tune nanoparticles self-assembly.

  2. Identifying deformation mechanisms in the NEEM ice core using EBSD measurements

    Science.gov (United States)

    Kuiper, Ernst-Jan; Weikusat, Ilka; Drury, Martyn R.; Pennock, Gill M.; de Winter, Matthijs D. A.

    2015-04-01

    Deformation of ice in continental sized ice sheets determines the flow behavior of ice towards the sea. Basal dislocation glide is assumed to be the dominant deformation mechanism in the creep deformation of natural ice, but non-basal glide is active as well. Knowledge of what types of deformation mechanisms are active in polar ice is critical in predicting the response of ice sheets in future warmer climates and its contribution to sea level rise, because the activity of deformation mechanisms depends critically on deformation conditions (such as temperature) as well as on the material properties (such as grain size). One of the methods to study the deformation mechanisms in natural materials is Electron Backscattered Diffraction (EBSD). We obtained ca. 50 EBSD maps of five different depths from a Greenlandic ice core (NEEM). The step size varied between 8 and 25 micron depending on the size of the deformation features. The size of the maps varied from 2000 to 10000 grid point. Indexing rates were up to 95%, partially by saving and reanalyzing the EBSP patterns. With this method we can characterize subgrain boundaries and determine the lattice rotation configurations of each individual subgrain. Combining these observations with arrangement/geometry of subgrain boundaries the dislocation types can be determined, which form these boundaries. Three main types of subgrain boundaries have been recognized in Antarctic (EDML) ice core¹². Here, we present the first results obtained from EBSD measurements performed on the NEEM ice core samples from the last glacial period, focusing on the relevance of dislocation activity of the possible slip systems. Preliminary results show that all three subgrain types, recognized in the EDML core, occur in the NEEM samples. In addition to the classical boundaries made up of basal dislocations, subgrain boundaries made of non-basal dislocations are also common. ¹Weikusat, I.; de Winter, D. A. M.; Pennock, G. M.; Hayles, M

  3. The Physical Mechanism of Core-Wide and Local Instabilities at the Forsmark-1 BWR

    International Nuclear Information System (INIS)

    Analytis, G. Th.

    1998-10-01

    During the last 15 years, the problem of BWR instabilities has attracted the attention of a number of researchers. From the theoretical point of view, one would be interested in physically understanding the mechanisms responsible for the in- and out-of-phase core wide power oscillations observed at certain operating points of the power-flow map in different BWRs. From the practical point of view, one must try to avoid these 'incidents' since either locally, or globally, the power may substantially exceed the prescribed levels. In this work, we shall use RAMONA3-12 and analyse a rather unusual instability incident at Forsmark-1 in which in addition to the core-wide fundamental spatial mode oscillation, there were local large amplitude power oscillations at different radial positions in the core. We were able to reproduce these unusual experimental findings by assuming that there are large amplitude Density Wave Oscillations (DWOs) in different bundles, induced by the fact that these bundles were not seated properly into the lower fuel support plate. (author)

  4. Neutronic and mechanical design of the reactor core of the Opus system

    Energy Technology Data Exchange (ETDEWEB)

    Raepsaet, X.; Pascal, S. [CEA Saclay, Dept. Modelisation de Systemes et Structures (DEN/DM2S), 91 - Gif sur Yvette (France)

    2007-07-01

    Since a few years now, Cea decided to maintain a waking state in its space nuclear activities by carrying out some conceptual studies of embarked nuclear power systems in the range of 100-500 kWe. Results stemming from these ongoing studies are gathered in the project OPUS -Optimized Propulsion Unit System-. This nuclear power system relies on a fast gas-cooled reactor concept coupled either to a Brayton cycle or to a more ambitious energy conversion system using a Hirn cycle to dramatically reduce the size of the radiator. The OPUS reactor core consists of an arrangement of enriched graphite elements of hexagonal cross-section. Their length is equal to the core diameter (48 cm). Coated fuel particles containing enriched (93%) uranium are embedded in these fuel elements. Each fuel element is designed with a centered axial channel through which flows the working fluid: a mixture of helium and xenon gas. This reactor is expected to have an operating life of over 2000 days at full power. In fact the main questions remain on the fuel element manufacturing and on the mechanical design (type and size of particles, packing fraction in the matrix, final core diameter and mass). Especially, the nuclear reactor has been defined considering the possible synergies with the next generation of terrestrial nuclear reactor (International Generation IV Forum). Based on relatively short-term technologies, the same reactor is designed to cover a wide range of power: 100 to 500 kWe without core design modification. The final reactor design presented in this paper is the result of a coupled analysis between the thermomechanical and the neutronic aspects.

  5. Nonlinear Thermo-mechanical Finite Element Analysis of Polymer Foam Cored Sandwich Structures including Geometrical and Material Nonlinearity

    DEFF Research Database (Denmark)

    Palleti, Hara Naga Krishna Teja; Thomsen, Ole Thybo; Taher, Siavash Talebi

    In this paper, polymer foam cored sandwich structures with fibre reinforced composite face sheets subjected to combined mechanical and thermal loads will be analysed using the commercial FE code ABAQUS® incorporating both material and geometrical nonlinearity. Large displacements and rotations...

  6. A new mechanism of hydrogen absorption in water-water reactor core materials

    International Nuclear Information System (INIS)

    Gann, V.V.; Gann, A.V.

    2012-01-01

    The spectrum of fast protons, generated in water by fast neutrons of WWER-1000 reactor core, has been calculated using the code MCNPX. The main mechanism of fast proton generation in the moderator is found to be elastic scattering of fast neutrons on hydrogen nuclei. Fast protons with mean energy 1 MeV flow towards the surface of cladding material at flux density ∼ 0.1 μA/cm 2 . Proton range distribution profile in cladding material is calculated. The range of fast protons in zirconium averages 20 μm, the maximal proton range is larger than 200 μm. The rate of hydrogen deposition in 40 μm layer amounts to 5 x 10 -5 H/n/μ. A role of the suggested mechanism in process of zirconium clad hydrogenation during reactor irradiation is discussed.

  7. Effects of chronic restraint stress on body weight, food intake, and hypothalamic gene expressions in mice.

    Science.gov (United States)

    Jeong, Joo Yeon; Lee, Dong Hoon; Kang, Sang Soo

    2013-12-01

    Stress affects body weight and food intake, but the underlying mechanisms are not well understood. We evaluated the changes in body weight and food intake of ICR male mice subjected to daily 2 hours restraint stress for 15 days. Hypothalamic gene expression profiling was analyzed by cDNA microarray. Daily body weight and food intake measurements revealed that both parameters decreased rapidly after initiating daily restraint stress. Body weights of stressed mice then remained significantly lower than the control body weights, even though food intake slowly recovered to 90% of the control intake at the end of the experiment. cDNA microarray analysis revealed that chronic restraint stress affects the expression of hypothalamic genes possibly related to body weight control. Since decreases of daily food intake and body weight were remarkable in days 1 to 4 of restraint, we examined the expression of food intake-related genes in the hypothalamus. During these periods, the expressions of ghrelin and pro-opiomelanocortin mRNA were significantly changed in mice undergoing restraint stress. Moreover, daily serum corticosterone levels gradually increased, while leptin levels significantly decreased. The present study demonstrates that restraint stress affects body weight and food intake by initially modifying canonical food intake-related genes and then later modifying other genes involved in energy metabolism. These genetic changes appear to be mediated, at least in part, by corticosterone.

  8. Bupleurum falcatum prevents depression and anxiety-like behaviors in rats exposed to repeated restraint stress.

    Science.gov (United States)

    Lee, Bombi; Yun, Hye-Yeon; Shim, Insop; Lee, Hyejung; Hahm, Dae-Hyun

    2012-03-01

    Previous studies have demonstrated that repeated restraint stress in rodents produces increases in depression and anxietylike behaviors and alters the expression of corticotrophinreleasing factor (CRF) in the hypothalamus. The current study focused on the impact of Bupleurum falcatum (BF) extract administration on repeated restraint stress-induced behavioral responses using the forced swimming test (FST) and elevated plus maze (EPM) test. Immunohistochemical examinations of tyrosine hydroxylase (TH) expression in rat brain were also conducted. Male rats received daily doses of 20, 50, or 100 mg/kg (i.p.) BF extract for 15 days, 30 min prior to restraint stress (4 h/day). Hypothalamicpituitary- adrenal axis activation in response to repeated restraint stress was confirmed base on serum corticosterone levels and CRF expression in the hypothalamus. Animals that were pre-treated with BF extract displayed significantly reduced immobility in the FST and increased open-arm exploration in the EPM test in comparison with controls. BF also blocked the increase in TH expression in the locus coeruleus of treated rats that experienced restraint stress. Together, these results demonstrate that BF extract administration prior to restraint stress significantly reduces depression and anxiety-like behaviors, possibly through central adrenergic mechanisms, and they suggest a role for BF extract in the treatment of depression and anxiety disorders.

  9. Isostructural solid-solid phase transition in monolayers of soft core-shell particles at fluid interfaces: structure and mechanics.

    Science.gov (United States)

    Rey, Marcel; Fernández-Rodríguez, Miguel Ángel; Steinacher, Mathias; Scheidegger, Laura; Geisel, Karen; Richtering, Walter; Squires, Todd M; Isa, Lucio

    2016-04-21

    We have studied the complete two-dimensional phase diagram of a core-shell microgel-laden fluid interface by synchronizing its compression with the deposition of the interfacial monolayer. Applying a new protocol, different positions on the substrate correspond to different values of the monolayer surface pressure and specific area. Analyzing the microstructure of the deposited monolayers, we discovered an isostructural solid-solid phase transition between two crystalline phases with the same hexagonal symmetry, but with two different lattice constants. The two phases corresponded to shell-shell and core-core inter-particle contacts, respectively; with increasing surface pressure the former mechanically failed enabling the particle cores to come into contact. In the phase-transition region, clusters of particles in core-core contacts nucleate, melting the surrounding shell-shell crystal, until the whole monolayer moves into the second phase. We furthermore measured the interfacial rheology of the monolayers as a function of the surface pressure using an interfacial microdisk rheometer. The interfaces always showed a strong elastic response, with a dip in the shear elastic modulus in correspondence with the melting of the shell-shell phase, followed by a steep increase upon the formation of a percolating network of the core-core contacts. These results demonstrate that the core-shell nature of the particles leads to a rich mechanical and structural behavior that can be externally tuned by compressing the interface, indicating new routes for applications, e.g. in surface patterning or emulsion stabilization.

  10. M.E.366-J embodiment design project: Portable foot restraint

    Science.gov (United States)

    Heaton, Randall; Meyer, Eikar; Schmidt, Davey; Enders, Kevin

    1994-01-01

    During space shuttle operations, astronauts require support to carry out tasks in the weightless environment. In the past, portable foot restraints (PFR) with orientations adjustable in pitch, roll, and yaw provided this support for payload bay operations. These foot restraints, however, were designed for specific tasks with a load limit of 111.2 Newtons. Since the original design, new applications for foot restraints have been identified. New designs for the foot restraints have been created to boost the operational work load to 444.8 Newtons and decrease setup times. What remains to be designed is an interface between the restraint system and the extravehicular mobility unit (EMU) boots. NASA provided a proposed locking device involving a spring-loaded mechanism. This locking mechanism must withstand loads of 1334.4 Newtons in any direction and weigh less than 222.4 Newtons. This paper develops an embodiment design for the interface between the PFR and the EMU boots. This involves design of the locking mechanism and a removable cleat that allows the boot to interface with this mechanism. The design team used the Paul Beitz engineering methodology to present the systematic development, structural analysis, and production considerations of the embodiment design. This methodology provides a basis for understanding the justification behind the decisions made in the design.

  11. International Space Station Crew Restraint Design

    Science.gov (United States)

    Whitmore, M.; Norris, L.; Holden, K.

    2005-01-01

    With permanent human presence onboard the International Space Station (ISS), crews will be living and working in microgravity, dealing with the challenges of a weightless environment. In addition, the confined nature of the spacecraft environment results in ergonomic challenges such as limited visibility and access to the activity areas, as well as prolonged periods of unnatural postures. Without optimum restraints, crewmembers may be handicapped for performing some of the on-orbit tasks. Currently, many of the tasks on ISS are performed with the crew restrained merely by hooking their arms or toes around handrails to steady themselves. This is adequate for some tasks, but not all. There have been some reports of discomfort/calluses on the top of the toes. In addition, this type of restraint is simply insufficient for tasks that require a large degree of stability. Glovebox design is a good example of a confined workstation concept requiring stability for successful use. They are widely used in industry, university, and government laboratories, as well as in the space environment, and are known to cause postural limitations and visual restrictions. Although there are numerous guidelines pertaining to ventilation, seals, and glove attachment, most of the data have been gathered in a 1-g environment, or are from studies that were conducted prior to the early 1980 s. Little is known about how best to restrain a crewmember using a glovebox in microgravity. In 2004, The Usability Testing and Analysis Facility (UTAF) at the NASA Johnson Space Center completed development/evaluation of several design concepts for crew restraints to meet the various needs outlined above. Restraints were designed for general purpose use, for teleoperation (Robonaut) and for use with the Life Sciences Glovebox. All design efforts followed a human factors engineering design lifecycle, beginning with identification of requirements followed by an iterative prototype/test cycle. Anthropometric

  12. A Parametric Study of the Acoustic Mechanism for Core-collapse Supernovae

    International Nuclear Information System (INIS)

    Harada, A.; Nagakura, H.; Iwakami, W.; Yamada, S.

    2017-01-01

    We investigate the criterion for the acoustic mechanism to work successfully in core-collapse supernovae. The acoustic mechanism is an alternative to the neutrino-heating mechanism. It was proposed by Burrows et al., who claimed that acoustic waves emitted by g -mode oscillations in proto-neutron stars (PNS) energize a stalled shock wave and eventually induce an explosion. Previous works mainly studied to which extent the g -modes are excited in the PNS. In this paper, on the other hand, we investigate how strong the acoustic wave needs to be if it were to revive a stalled shock wave. By adding the acoustic power as a new axis, we draw a critical surface, which is an extension of the critical curve commonly employed in the context of neutrino heating. We perform both 1D and 2D parametrized simulations, in which we inject acoustic waves from the inner boundary. In order to quantify the power of acoustic waves, we use the extended Myers theory to take neutrino reactions into proper account. We find for the 1D simulations that rather large acoustic powers are required to relaunch the shock wave, since the additional heating provided by the secondary shocks developed from acoustic waves is partially canceled by the neutrino cooling that is also enhanced. In 2D, the required acoustic powers are consistent with those of Burrows et al. Our results seem to imply, however, that it is the sum of neutrino heating and acoustic powers that matters for shock revival.

  13. A Parametric Study of the Acoustic Mechanism for Core-collapse Supernovae

    Energy Technology Data Exchange (ETDEWEB)

    Harada, A. [Physics Department, University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-0033 (Japan); Nagakura, H. [TAPIR, Walter Burke Institue for Theoretical Physics, Mailcode 350-17, California Institute of Technology, Pasadena, CA 91125 (United States); Iwakami, W.; Yamada, S., E-mail: harada@utap.phys.s.u-tokyo.ac.jp [Advanced Research Institute for Science and Engineering, Waseda University, 3-4-1 Okubo, Shinjuku, Tokyo 169-8555 (Japan)

    2017-04-10

    We investigate the criterion for the acoustic mechanism to work successfully in core-collapse supernovae. The acoustic mechanism is an alternative to the neutrino-heating mechanism. It was proposed by Burrows et al., who claimed that acoustic waves emitted by g -mode oscillations in proto-neutron stars (PNS) energize a stalled shock wave and eventually induce an explosion. Previous works mainly studied to which extent the g -modes are excited in the PNS. In this paper, on the other hand, we investigate how strong the acoustic wave needs to be if it were to revive a stalled shock wave. By adding the acoustic power as a new axis, we draw a critical surface, which is an extension of the critical curve commonly employed in the context of neutrino heating. We perform both 1D and 2D parametrized simulations, in which we inject acoustic waves from the inner boundary. In order to quantify the power of acoustic waves, we use the extended Myers theory to take neutrino reactions into proper account. We find for the 1D simulations that rather large acoustic powers are required to relaunch the shock wave, since the additional heating provided by the secondary shocks developed from acoustic waves is partially canceled by the neutrino cooling that is also enhanced. In 2D, the required acoustic powers are consistent with those of Burrows et al. Our results seem to imply, however, that it is the sum of neutrino heating and acoustic powers that matters for shock revival.

  14. FFTF irradiation of fracture mechanics specimens for out-of-core structures

    International Nuclear Information System (INIS)

    King, D.C.

    1978-09-01

    The National Program Plan has established data requirements for out-of-core structures for FBRs. Significant FFTF irradiation space with moderate gamma heating levels is required to irradiate relatively large fracture mechanics specimens to total neutron fluences ranging between 5 x 10 21 and 5 x 10 22 n/cm 2 and temperatures which range between 400 0 C (750 0 F) and 650 0 C (1200 0 F). Priority 1 data on stainless steel welds requires a test volume of 7443 cm 3 (454 in 3 ). Priority 2 data on 304 and 316 SS and Inconel 718 materials and Inconel 718 welds requires 2760 cm 3 (168 in 3 ). Priority 3 data on stainless steels, other nickel-base alloys, and ferritics requires 33,118 cm 3 (2021 in 3 ). Priority 4 data at elevated temperatures on stainless steels, other nickel-base alloys and ferritics requires 69,182 cm 3

  15. Effect of neutron radiation on mechanical properties of permanent near core structures

    International Nuclear Information System (INIS)

    Tavassoli, A.A.

    1988-01-01

    Several hundred specimens have been tested in order to assess the effects of low dose neutron radiation ( 0 C and ductility and toughness are primary design concerns, the changes provoked, by doses up to 1.3 dpa, in overall mechanical properties of welded joints are small. For upper core structure, where the operating temperature is about 550 0 C and fatigue and creep resistance are major design needs, the changes induced, through formation of up to about 2 appm helium, in conventional fatigue properties or fatigue with short hold times are negligible. With increasing hold time, intergranular rupture in irradiated specimens is enhanced but the limited number of tests does not allow definite conclusions to be drawn. 53 refs, 3 tabs, 9 figs

  16. Acute Cold / Restraint Stress in Castrated Rats

    Directory of Open Access Journals (Sweden)

    Farideh Zafari Zangeneh

    2008-09-01

    Full Text Available Objective: The present study aimed to determine whether castration altered osmotically stimulated vasopressin (VP release and urinary volume and what is the role of endocrine-stress axis in this process.Materials and methods: Totally 108 mice were studied in two main groups of castrated (n=78 and control (n=30. Each group was extracted by acute cold stress (4◦C for 2h/day, restraint stress (by syringes 60cc 2h/day and cold/restraint stress. The castrated group was treated in sub groups of testosterone, control (sesame oil as vehicle of testosterone. Propranolol as blocker of sympathetic nervous system was given to both groups of castrated mice and main control.Results: Our results showed that, there is interactions between testosterone and sympathetic nervous system on vasopressin, because urine volume was decreased only in testoctomized mice with cold/restraint and cold stress (P<0.001; propranolol as the antagonist of sympathetic nervous system could block and increase urine volume in castrated mice. This increased volume of urine was due to acute cold stress, not restraint stress (p<0.001. The role of testosterone, noradrenalin (NA and Vasopressin (VP in the acute cold stress is confirmed, because testosterone could return the effect of decreased urine volume in control group (P<0.001. Conclusion: Considering the effect of cold/restraint stress on urinary volume in castrated mice shows that there is interaction between sex hormone (testosterone, vasopressin and adrenergic systems.

  17. Roadside observation of child passenger restraint use

    Directory of Open Access Journals (Sweden)

    Beth Bruce

    2015-10-01

    Full Text Available Background: Despite legislation and research evidence supporting the use of childhood vehicle restraints, motor vehicle crashes remain the leading cause of injury, death and disability among Canadian children. Methods: Working in collaboration with trained car seat specialists and police officers, roadside checks were conducted to observe correct use of child restraints. Results: Of the 1323 child vehicle restraints inspected, 99.6% of the children were restrained, 91% were in the correct seat, and 48% of restraints were correctly installed. The seat/restraint types most used incorrectly used were booster seats (31% and seat belts (53%. The majority of incorrectly installed or fitted seats (55% were forward facing. Common errors in installation and fit included the seat not being secured tightly enough to the vehicle, incorrect tether strap use, the harness not being tight enough, and/or the chest clip being in the wrong place. Conclusions: The greatest proportion of incorrect seat use was among those children who transitioned to a seat belt too soon. The greatest proportion of installation and fit errors were among forward facing seats. Researchers recommend: 1 targeting parents with older children (ages 3 and above regarding transitioning too soon from forward facing seats to booster seats, and from booster seats to seat belts; 2 targeting parents with younger children regarding correct installation of rear facing and forward facing seats; 3 collaborating with police officers to review the most common errors and encourage observation at roadside checks; and 4 creating community awareness by way of roadside checks.

  18. Computer simulation of migration atomic mechanism and substitutional impurity interaction with screw dislocation core in bcc lattice

    International Nuclear Information System (INIS)

    Klyavin, O.V.; Likhodedov, N.P.; Orlov, A.N.

    1986-01-01

    Distribution and migration of substitutional impurity atoms (He and C) in the screw dislocation core of the 1/2 type is studied in α-Fe. The atomic mechanism of impurity atom diffusion over screw dislocation core, consisting in the fact that impurity migration proceeds in a screw trajectory, is discovered and analyzed. It is shown that tubular He diffusion over screw dislocation may proceed at T <= 300 K

  19. Legislating child restraint usage -Its effect on self-reported child restraint use rates in a central city.

    Science.gov (United States)

    Brixey, Suzanne; Ravindran, Karthik; Guse, Clare E

    2010-02-01

    To assess the effect of the newly enacted child passenger safety law, Wisconsin Act 106, on self-report of proper restraint usage of children in Milwaukee's central city population. A prospective, non-randomized study design was used. The settings used were (a) a pediatric urban health center, and (b) two Women, Infants and Children offices in Milwaukee, Wisconsin. Participants included 11,566 surveys collected over 18 months that spanned the pre-legislation and post-legislation time periods from February 2006 through August 2008. The study set out to assess appropriate child passenger restraint. The results showed that the changes in adjusted proper restraint usage rates for infants between the pre-law, grace period, and post-fine periods were 94%, 94%, and 94% respectively. For children 1-3years old, the adjusted proper usage rates were 65%, 63%, and 59%, respectively. And for children 4-7years old, the rates were 43%, 44% and 42%, respectively. There was a significant increase in premature booster seat use in children who should have been restrained in a rear- or forward-facing car seat (10% pre-law, 12% grace period, 20% post-fine; padvertising and marketing to the correct age group, ease of installation, and mechanisms to prevent incorrect safety strap and harness placement. To ensure accurate and consistent use on every trip, car seat manufacturers must ensure that best practice recommendations for use as well as age, weight, and height be clearly specified on each child restraint. The authors support the United States Department of Transportation's new consumer program that will assist caregivers in identifying the child seat that will fit in their vehicle. In addition, due to the increase in premature graduation of children into belt-positioning booster seats noted as a result of legislation, promoting and marketing booster seat use for children less than 40 pounds should not be accepted. Child passenger safety technicians must continue to promote best

  20. Performance evaluation of CPF shredder type mechanical crusher with simulated core fuel pin

    International Nuclear Information System (INIS)

    Nakahara, Masaumi; Sano, Yuichi; Aose, Shin-ichi

    2006-12-01

    In the advanced aqueous reprocessing system, powder fuel dissolution has been investigated, which is quite effective on the dissolution for highly concentrated solution. As one of the effective means that powder the irradiated MOX fuel, we have been developing shredder type mechanical crusher. This apparatus can automatically crush the sheared fuel pieces by twin-shaft disk blades, powder the crushed fragments by disk blades and screen blade, and recover the powdered fuel. The shredder type mechanical crusher was developed for using in a hot cell in Chemical Processing Facility, and the first crush experiment with this crusher was carried out at July 2004 using the simulated core fuel pin. This experiment showed that the crushed fragments could not be grinded efficiency because screen blade vibrated up and down during the operation. Additionally, the strength of screen blade block was insufficient to crush the sheared fuel pieces stably. Therefore, about 70% of fuel was recovered in maximum. Based on the results of the first experiment, screen blade was fixed up mainly and the second experiment was carried out with improved apparatus at September 2005. In this experiment, about 96% of fuel could be recovered in maximum because screen blade was stable during the operation. (J.P.N.)

  1. Analysis for mechanical consequences of a core disruptive accident in Prototype Fast Breeder Reactor

    International Nuclear Information System (INIS)

    Chellapandi, P.; Velusamy, K.; Chetal, S.C.; Bhoje, S.B.; Lal, H.; Sethi, V.S.

    2003-01-01

    The mechanical consequences of a core disruptive accident (CDA) in a fast breeder reactor are described. The consequences are development of deformations and strains in the vessels, intermediate heat exchangers (IHX) and decay heat exchangers (DHX), impact of sodium slug on the bottom surface of the top shield, sodium release to reactor containment building through top shield penetrations, sodium fire and consequent temperature and pressure rise in reactor containment building (RCB). These are quantified for 500 MWe Prototype Fast Breeder Reactor (PFBR) for a CDA with 100 MJ work potential. The results are validated by conducting a series of experiments on 1/30 and 1/13 scaled down models with increasing complexities. Mechanical energy release due to nuclear excursion is simulated by chemical explosion of specially developed low density explosive charge. Based on these studies, structural integrity of primary containment, IHX and DHX is demonstrated. The sodium release to RCB is 350 kg which causes pressure rise of 12 kPa in RCB. (author)

  2. Striving for balance between caring and restraint

    DEFF Research Database (Denmark)

    Moberg, Julie Y; Larsen, Dorte; Brødsgaard, Anne

    2017-01-01

    with 14 young adults were conducted. RESULTS: The essence of the phenomenon of having a parent with multiple sclerosis was synthesized into 'Striving for balance between caring and restraint' from two themes 'caring' and 'restraint' and eight subthemes. Participants' experiences of caring for parents...... that one of the greatest challenges of having a parent with multiple sclerosis is achieving a balance between caring for others and asserting one's own desires. RELEVANCE TO CLINICAL PRACTICE: Health care professionals can support the family by encouraging family members to participate in consultations...

  3. Acute restraint stress induces endothelial dysfunction: role of vasoconstrictor prostanoids and oxidative stress.

    Science.gov (United States)

    Carda, Ana P P; Marchi, Katia C; Rizzi, Elen; Mecawi, André S; Antunes-Rodrigues, José; Padovan, Claudia M; Tirapelli, Carlos R

    2015-01-01

    We hypothesized that acute stress would induce endothelial dysfunction. Male Wistar rats were restrained for 2 h within wire mesh. Functional and biochemical analyses were conducted 24 h after the 2-h period of restraint. Stressed rats showed decreased exploration on the open arms of an elevated-plus maze (EPM) and increased plasma corticosterone concentration. Acute restraint stress did not alter systolic blood pressure, whereas it increased the in vitro contractile response to phenylephrine and serotonin in endothelium-intact rat aortas. NG-nitro-l-arginine methyl ester (l-NAME; nitric oxide synthase, NOS, inhibitor) did not alter the contraction induced by phenylephrine in aortic rings from stressed rats. Tiron, indomethacin and SQ29548 reversed the increase in the contractile response to phenylephrine induced by restraint stress. Increased systemic and vascular oxidative stress was evident in stressed rats. Restraint stress decreased plasma and vascular nitrate/nitrite (NOx) concentration and increased aortic expression of inducible (i) NOS, but not endothelial (e) NOS. Reduced expression of cyclooxygenase (COX)-1, but not COX-2, was observed in aortas from stressed rats. Restraint stress increased thromboxane (TX)B(2) (stable TXA(2) metabolite) concentration but did not affect prostaglandin (PG)F2α concentration in the aorta. Restraint reduced superoxide dismutase (SOD) activity, whereas concentrations of hydrogen peroxide (H(2)O(2)) and reduced glutathione (GSH) were not affected. The major new finding of our study is that restraint stress increases vascular contraction by an endothelium-dependent mechanism that involves increased oxidative stress and the generation of COX-derived vasoconstrictor prostanoids. Such stress-induced endothelial dysfunction could predispose to the development of cardiovascular diseases.

  4. Chronic restraint stress exacerbates nociception and inflammatory response induced by bee venom in rats: the role of the P2X7 receptors.

    Science.gov (United States)

    Li, Xiao-Qiu; Li, Man; Zhou, Zhong-He; Liu, Bao-Jun; Chen, Hui-Sheng

    2016-02-01

    Chronic restraint stress exacerbates pain and inflammation. The present study was designed to evaluate the effect of chronic restraint stress on inflammatory pain induced by subcutaneous injection of bee venom (BV). First, we investigated: (1) the effect of two-week restraint stress with daily 2 or 8 h on the baseline paw withdrawal mechanical threshold (PWMT), paw withdrawal thermal latency (PWTL) and paw circumference (PC); (2) the effect of chronic stress on the spontaneous paw-flinching reflex (SPFR), decrease in PWM, PWTL and increase in PC of the injected paw induced by BV. The results showed that (1) chronic restraint decreased significantly the PWMT and inhibited significantly the increase in PC, but had no effect on PWTL, compared with control group; (2) chronic restraint enhanced significantly BV-induced SPFR and inflammatory swelling of the injected paw. In a second series of experiments, the role of P2X7 receptor (P2X7R) in the enhancement of BV-induced inflammatory pain produced by chronic restraint stress was determined. Systemic pretreatment with P2X7R antagonist completely reversed the decrease in PWMT produced by chronic restraint, inhibited significantly the enhancement of BV-induced inflammatory pain produced by chronic restraint stress. Taken together, our data indicate that chronic restraint stress-enhanced nociception and inflammation in the BV pain model, possibly involving the P2X7R.

  5. Astronaut Anna Fisher demonstrates sleep restraints on shuttle

    Science.gov (United States)

    1984-01-01

    Astronaut Anna L. Fisher demonstrates the versatility of shuttle sleep restraints to accommodate the preference of crewmembers as she appears to have configured hers in a horizontal hammock mode. Stowage lockers, one of the middeck walls, another sleep restraint, a jury-rigged foot and hand restraint are among other items in the frame.

  6. Physical Restraint Initiation in Nursing Homes and Subsequent Resident Health

    Science.gov (United States)

    Engberg, John; Castle, Nicholas G.; McCaffrey, Daniel

    2008-01-01

    Purpose: It is widely believed that physical restraint use causes mental and physical health decline in nursing home residents. Yet few studies exist showing an association between restraint initiation and health decline. In this research, we examined whether physical restraint initiation is associated with subsequent lower physical or mental…

  7. Restraint, tendency toward overeating and ice cream consumption

    NARCIS (Netherlands)

    Van Strien, T; Cleven, A.H.G.; Schippers, G.

    2000-01-01

    OBJECTIVE: The examination of the prediction of grams of ice cream eaten by preload, restraint, susceptibility toward overeating, and interaction terms. METHOD: A milkshake-ice cream study on 200 females using the Restraint Scale (RS) and the restraint and disinhibition scales from the Three-Factor

  8. EFFECTS OF CORE STABILIZATION PROGRAM AND CONVENTIONAL EXERCISES IN THE MANAGEMENT OF PATIENTS WITH CHRONIC MECHANICAL LOW BACK PAIN

    Directory of Open Access Journals (Sweden)

    Suresh Babu Reddy .A

    2015-04-01

    Full Text Available Background: Conventional back care exercises are advocated to treat the pain and to strengthen the involved muscles. There will be possibility of the pain getting recurred due to disproportionate balance and stability in the muscles. The core stabilization is major trend in rehabilitation, it aims at improving stability during functional activities, balance, flexibility, strength training and effectively manage the pain as well. Objective: To find the efficacy of the concept of core stabilization when compared to conventional back care exercises in patients with chronic mechanical low back pain. Methods: Forty patients with chronic Mechanical Low back pain were selected through purposive sampling and were randomly assigned into control group who received conventional back exercises and SWD (n=20, experimental group who received core stabilization and SWD (n=20. Both the groups received SWD, along with conventional back exercises for one group and core stabilization for the other group three days a week for 6 weeks. The treatment outcome was assessed using visual analogue scale, Rolland Morris Disability Questionnaire and Lumbar range of motion using goniometer. Results: After a 6 weeks training period the core stabilization group scored significantly higher than the conventional group for VAS (p=0.05 RMDQ (p=0.05 whereas ROM improved higher in conventional group (p=0.05. Conclusion: After the treatment sessions Core stabilization group registered a significant improvement when compared to conventional back care exercises in improving function and in relieving pain.

  9. Mechanical properties of chemically bonded sand core materials dipped in sol-gel coating impregnated with filter

    DEFF Research Database (Denmark)

    Nwaogu, Ugochukwu Chibuzoh; Tiedje, Niels Skat

    2012-01-01

    A novel sol-gel coating impregnated with filter dust was applied on chemically bonded sand core materials by dipping. After curing, the strengths of the core materials were measured under uniaxial loading using a new strength testing machine (STM). The STM presents the loading history as a force-...... of the chemically bonded sand core materials, a combination of flexural and compression tests is suggested for improving the casting quality. © 2012 W. S. Maney & Son Ltd.......A novel sol-gel coating impregnated with filter dust was applied on chemically bonded sand core materials by dipping. After curing, the strengths of the core materials were measured under uniaxial loading using a new strength testing machine (STM). The STM presents the loading history as a force...... the strengths were increased under compression. The mode of fracture of the chemically bonded sand core materials was observed to be intergranular through the binder. The stiffness of the chemically bonded sand core materials was determined. For better understanding of the mechanical properties...

  10. Dietary restraint and impulsivity modulate neural responses to food in adolescents with obesity and healthy adolescents.

    Science.gov (United States)

    Hofmann, Johannes; Ardelt-Gattinger, Elisabeth; Paulmichl, Katharina; Weghuber, Daniel; Blechert, Jens

    2015-11-01

    Despite alarming prevalence rates, surprisingly little is known about neural mechanisms underlying eating behavior in juveniles with obesity. To simulate reactivity to modern food environments, event-related potentials (ERP) to appetizing food images (relative to control images) were recorded in adolescents with obesity and healthy adolescents. Thirty-four adolescents with obesity (patients) and 24 matched healthy control adolescents watched and rated standardized food and object images during ERP recording. Personality (impulsivity) and eating styles (trait craving and dietary restraint) were assessed as potential moderators. Food relative to object images triggered larger early (P100) and late (P300) ERPs. More impulsive individuals had considerably larger food-specific P100 amplitudes in both groups. Controls with higher restraint scores showed reduced food-specific P300 amplitudes and subjective palatability ratings whereas patients with higher restraint scores showed increased P300 and palatability ratings. This first ERP study in adolescents with obesity and controls revealed impulsivity as a general risk factor in the current obesogenic environment by increasing food-cue salience. Dietary restraint showed paradoxical effects in patients, making them more vulnerable to visual food-cues. Salutogenic therapeutic approaches that deemphasize strict dietary restraint and foster healthy food choice might reduce such paradoxical effects. © 2015 The Obesity Society.

  11. Restraint Stress Impairs Glucose Homeostasis Through Altered ...

    African Journals Online (AJOL)

    olayemitoyin

    serum level of adiponectin was significantly (p< 0.05) lower compared with ... were significantly (p< 0.05) decreased in the skeletal muscle of restraint stress exposed rats. ... controlled conditions for the light/dark cycle, ..... increase the production of catecholamines. ... specific protein that has been suggested to play a role.

  12. The use of restraints in psychiatric patients

    African Journals Online (AJOL)

    2009-09-17

    Sep 17, 2009 ... In South Africa, according to the Mental Health Care Act No. 17 of 2002 .... and staff composition, type of ward and ward atmosphere. The type of ... (e.g. psychiatric diagnosis, strengths, family history), and restraint should be ...

  13. PDBStat: a universal restraint converter and restraint analysis software package for protein NMR

    International Nuclear Information System (INIS)

    Tejero, Roberto; Snyder, David; Mao, Binchen; Aramini, James M.; Montelione, Gaetano T.

    2013-01-01

    The heterogeneous array of software tools used in the process of protein NMR structure determination presents organizational challenges in the structure determination and validation processes, and creates a learning curve that limits the broader use of protein NMR in biology. These challenges, including accurate use of data in different data formats required by software carrying out similar tasks, continue to confound the efforts of novices and experts alike. These important issues need to be addressed robustly in order to standardize protein NMR structure determination and validation. PDBStat is a C/C++ computer program originally developed as a universal coordinate and protein NMR restraint converter. Its primary function is to provide a user-friendly tool for interconverting between protein coordinate and protein NMR restraint data formats. It also provides an integrated set of computational methods for protein NMR restraint analysis and structure quality assessment, relabeling of prochiral atoms with correct IUPAC names, as well as multiple methods for analysis of the consistency of atomic positions indicated by their convergence across a protein NMR ensemble. In this paper we provide a detailed description of the PDBStat software, and highlight some of its valuable computational capabilities. As an example, we demonstrate the use of the PDBStat restraint converter for restrained CS-Rosetta structure generation calculations, and compare the resulting protein NMR structure models with those generated from the same NMR restraint data using more traditional structure determination methods. These results demonstrate the value of a universal restraint converter in allowing the use of multiple structure generation methods with the same restraint data for consensus analysis of protein NMR structures and the underlying restraint data

  14. PDBStat: a universal restraint converter and restraint analysis software package for protein NMR

    Energy Technology Data Exchange (ETDEWEB)

    Tejero, Roberto [Rutgers, The State University of New Jersey, Center for Advanced Biotechnology and Medicine (United States); Snyder, David [William Paterson University, Department of Chemistry (United States); Mao, Binchen; Aramini, James M.; Montelione, Gaetano T., E-mail: guy@cabm.rutgers.edu [Rutgers, The State University of New Jersey, Center for Advanced Biotechnology and Medicine (United States)

    2013-08-15

    The heterogeneous array of software tools used in the process of protein NMR structure determination presents organizational challenges in the structure determination and validation processes, and creates a learning curve that limits the broader use of protein NMR in biology. These challenges, including accurate use of data in different data formats required by software carrying out similar tasks, continue to confound the efforts of novices and experts alike. These important issues need to be addressed robustly in order to standardize protein NMR structure determination and validation. PDBStat is a C/C++ computer program originally developed as a universal coordinate and protein NMR restraint converter. Its primary function is to provide a user-friendly tool for interconverting between protein coordinate and protein NMR restraint data formats. It also provides an integrated set of computational methods for protein NMR restraint analysis and structure quality assessment, relabeling of prochiral atoms with correct IUPAC names, as well as multiple methods for analysis of the consistency of atomic positions indicated by their convergence across a protein NMR ensemble. In this paper we provide a detailed description of the PDBStat software, and highlight some of its valuable computational capabilities. As an example, we demonstrate the use of the PDBStat restraint converter for restrained CS-Rosetta structure generation calculations, and compare the resulting protein NMR structure models with those generated from the same NMR restraint data using more traditional structure determination methods. These results demonstrate the value of a universal restraint converter in allowing the use of multiple structure generation methods with the same restraint data for consensus analysis of protein NMR structures and the underlying restraint data.

  15. Mechanic properties analysis of quasi-square honeycomb sandwich structure′s core

    Directory of Open Access Journals (Sweden)

    Guan TONG

    2017-12-01

    Full Text Available In order to illustrate the relationship between the quasi-square-honeycomb structure and the hexagonal honeycomb structure, after decomposing the quasi-square honeycomb sandwich structure into unique T-shaped cell, the equivalent elastic constants equations of T-shaped cell model are derived respectively by applying Euler beam theory and energy method. At the same time, the quasi-square honeycomb's characteristic structure parameters are substituted into the equivalent elastic constants equations which are derived by the classical method of a hexagonal honeycomb core, and the same results are obtained as that of the preceding both methods. It is proved that the quasi-square-honeycomb structure is an evolution of hexagonal honeycomb. The limitations and application scope of the two classical honeycomb formulas are pointed out. The research of the structural characteristics of the square-shaped honeycomb shows that the classical cellular theoretical formula are singular and inaccurate when the feature angle values equal to zero or near zero. This study has important reference value for the subsequent research and improvement of the theories about cellular structure mechanical properties.

  16. Data Acquisition System Design for Advanced Core-Cooling Mechanism Experiment

    International Nuclear Information System (INIS)

    Zhang, Ziyang; Tian, Fang; Zhang, Tao; Wang, Shen

    2011-01-01

    Data Acquisition System (DAS) design for Advanced Core-Cooling Mechanism Experiment(ACME) is studied in the paper. DAS is an important connection between test facility and result analysis. Firstly, it introduces DAS and its design requirement for ACME. Nearly one thousand data resources need record in ACME. They have different types and acquisition frequencies. In order to record these data, a large scale and high speed layered data acquisition system is developed. Secondly, it discusses the DAS design for ACME, including the analog signal adjusting circuits, clock circuit design, sampling frequencies, data storage and transmission by large database system, anti-interference and etc. Analog signal adjusting circuits are necessary to deal with different kinds of input data to gain standard data resources. Some data change slowly and others change in several seconds according to the test performed on ACME. So it is difficult to use uniform sampling frequencies, and a layered data acquisition system is introduced. A large database is built to store data for ACME test, which keeps data safer and makes subsequent data handling more convenient. A database hot backup is also applied to ensure data safety. The software of DAS is built by Labview, which can provide intuitionist result and friendly interface. Another important function of DAS is the ACME safety protection. Finally, the characteristics and improvement of DAS for ACME is analyzed compared to other test facility. Besides friendly user interface, DAS of ACME can also assure higher data precision and sampling frequency

  17. The mechanism of translational displacements of the core of the Earth at inversion molten and solidification of substance at core-mantle boundary in opposite hemispheres

    Science.gov (United States)

    Barkin, Yu. V.

    2009-04-01

    Shell dynamics. "The Earth represents system of non-spherical eccentric shells (the core, the mantle, a rigid core etc.) which have various structure and distribution of density. Their moments of inertia and dynamic oblatenesses are various. From the point of view of the mechanics it means, that external celestial bodies (the Moon and the Sun) on miscellaneous (differentially) gravitationally act on the separate shells. They try to cause various accelerations to the centers of masses of shells and various angular accelerations to their rotary motions. It the most external celestial bodies put shells of forced body in difficult state, forcing them to push each other to prevent each other and to struggle with each other. That is between shells there are powerful force interactions: additional forces, and more significant on value, than tidal forces, and the huge moments of forces which all time aspire to turn one of shells relatively to another. The external influence is stronger, the shells are pressed more strongly or taken away. If external action weakens, also shells mutually exist more quietly. External influence depends on position of perturbing celestial bodies. But the last vary cyclically in various time scales. It means, that interactions of shells with each other also are cyclic with the set of frequencies being a derivative from basic frequencies of orbital motions of celestial bodies (coincide with basic frequencies or are their various combinations). Clearly, that the specified mechanical interactions are as though primary which generate then a sequence of every possible interactions of all layers of shells, geodynamic and geophysical processes (which are naturally also cyclic). Elastic layers will test deformations, thus absorbing, and then returning a mechanical energy of translatory - rotary motion of shells and their relative swing. Plastic properties of layers of shells will result in absorption of mechanical energy and to its transformation to

  18. Real-world adjustments of driver seat and head restraint in Saab 9-3 vehicles.

    Science.gov (United States)

    Carlsson, Anna; Pipkorn, Linda; Kullgren, Anders; Svensson, Mats

    2017-05-19

    Whiplash-associated disorder (WAD), commonly denoted whiplash injury, is a worldwide problem. These injuries occur at relatively low changes of velocity (typically whiplash injury than males.  Improved seat design is the prevailing means of increasing the protection of whiplash injury for occupants in rear impacts. Since 1997, more advanced whiplash protection systems have been introduced on the market, the Saab Active Head Restraint (SAHR) being one of the most prominent. The SAHR-which is height adjustable-is mounted to a pressure plate in the seatback by means of a spring-resisted link mechanism.  Nevertheless, studies have shown that seats equipped with reactive head restraints (such as the SAHR) have a very high injury-reducing effect for males (∼60-70%) but very low or no reduction effect for females. One influencing factor could be the position of the head restraint relative to the head, because a number of studies have reported that adjustable head restraints often are incorrectly positioned by drivers.  The aim was to investigate how female and male Saab drivers adjust the seat in the car they drive the most. The seated positions of drivers in stationary conditions have been investigated in a total of 76 volunteers (34 females, 42 males) who participated in the study. Inclusion criteria incorporated driving a Saab 9-3 on a regularly basis. The majority of the volunteers (89%) adjusted the head restraint to any of the 3 uppermost positions and as many as 59% in the top position.  The average vertical distance between the top of the head and the top of the head restraint (offset) increase linearly with increasing statures, from an average of -26 mm (head below the head restraint) for small females to an average of 82 mm (head above the head restraint) for large males. On average, the offset was 23 mm for females, which is within a satisfactory range and in accordance with recommendations; the corresponding value for males was 72 mm.

  19. Embedding Hands-On Mini Laboratory Experiences in a Core Undergraduate Fluid Mechanics Course: A Pilot Study

    Science.gov (United States)

    Han, Duanduan; Ugaz, Victor

    2017-01-01

    Three self-contained mini-labs were integrated into a core undergraduate fluid mechanics course, with the goal of delivering hands-on content in a manner scalable to large class sizes. These mini-labs supported learning objectives involving friction loss in pipes, flow measurement, and centrifugal pump analysis. The hands-on experiments were…

  20. Learner Characteristic Based Learning Effort Curve Mode: The Core Mechanism on Developing Personalized Adaptive E-Learning Platform

    Science.gov (United States)

    Hsu, Pi-Shan

    2012-01-01

    This study aims to develop the core mechanism for realizing the development of personalized adaptive e-learning platform, which is based on the previous learning effort curve research and takes into account the learner characteristics of learning style and self-efficacy. 125 university students from Taiwan are classified into 16 groups according…

  1. Reduction of Restraint of People with Intellectual Disabilities: An Organizational Behavior Management (OBM) Approach

    Science.gov (United States)

    Williams, Don E.; Grossett, Deborah L.

    2011-01-01

    We used an organizational behavior management (OBM) approach to increase behavior intervention plans and decrease the use of mechanical restraint. First, recipients were tracked as a member of the priority group if they engaged in frequent self-injurious behavior or physical aggression toward others and/or if they had been placed in mechanical…

  2. Restraint Procedures and Challenging Behaviours in Intellectual Disability: An Analysis of Causative Factors

    Science.gov (United States)

    Matson, Johnny L.; Boisjoli, Jessica A.

    2009-01-01

    Background: Persons with intellectual disability often evince challenging behaviours. Efforts have been underway for some time to develop prosocial or positive skill acquisition treatments to address challenging behaviours. However, physical/mechanical and chemical restraint is still commonly used in many clinical and community settings. Such…

  3. Experimental study of the mechanical behaviour of pin reinforced foam core sandwich materials under shear load

    International Nuclear Information System (INIS)

    Dimassi, M A; Brauner, C; Herrmann, A S

    2016-01-01

    Sandwich structures with a lightweight closed cell hard foam core have the potential to be used in primary structures of commercial aircrafts. Compared to honeycomb core sandwich, the closed cell foam core sandwich overcomes the issue of moisture take up and makes the manufacturing of low priced and highly integrated structures possible. However, lightweight foam core sandwich materials are prone to failure by localised external loads like low velocity impacts. Invisible cracks could grow in the foam core and threaten the integrity of the structure. In order to enhance the out-of-plane properties of foam core sandwich structures and to improve the damage tolerance (DT) dry fibre bundles are inserted in the foam core. The pins are infused with resin and co-cured with the dry fabric face sheets in an out-of-autoclave process. This study presents the results obtained from shear tests following DIN 53294-standard, on flat sandwich panels. All panels were manufactured with pin-reinforcement manufactured with the Tied Foam Core Technology (TFC) developed by Airbus. The effects of pin material (CFRP and GFRP) and pin volume fraction on the shear properties of the sandwich structure and the crack propagation were investigated and compared to a not pinned reference. It has been concluded that the pin volume fraction has a remarkable effect on the shear properties and damage tolerance of the observed structure. Increasing the pin volume fraction makes the effect of crack redirection more obvious and conserves the integrity of the structure after crack occurrence. (paper)

  4. Thermal and mechanical design of the plasma core CXRS diagnostics for the fusion reactor ITER; Thermische und mechanische Auslegung der Plasma Core CXRS Diagnostik des ITER Kernfusionsreaktors

    Energy Technology Data Exchange (ETDEWEB)

    Greza, H. [WTI Wissenschaftlich-Technische Ingenieurberatung GmbH, Juelich (Germany); Neubauer, O.; Wolters, J. [Forschungszentrum Juelich GmbH (Germany)

    2009-07-01

    In the frame of the research project ITER (international thermonuclear experimental reactor) the plasma state is monitored using the plasma core diagnostics CXRS (charge exchange recombination spectroscopy).The authors describe the thermal and mechanical design of the first mirror of the CXRS diagnostics. The components of the first mirror are exposed to high heat and neutron irradiation. The surface temperature will be 300 to 400 deg C. The misalignment tolerance is plus or minus 0.1 degree. The maximum mechanical stresses in the mirror have to be minimized. The design calculations use the finite element code ANSYS. The results indicate that the heat input from the plasma can be removed by the coolant flow. Further calculation shave to concern the brazed joints between mirror and cooling block.

  5. Thermal and mechanical design of the plasma core CXRS diagnostics for the fusion reactor ITER; Thermische und mechanische Auslegung der Plasma Core CXRS Diagnostik des ITER Kernfusionsreaktors

    Energy Technology Data Exchange (ETDEWEB)

    Greza, H.; Knauff, R. [Wissenschaftlich-Technische Ingenieurberatung GmbH (WTI), Juelich (Germany); Neubauer, O.; Wolters, J.; Offermanns, G.; Biel, W. [Forschungszentrum Juelich GmbH (Germany)

    2011-07-01

    In the frame of the research project ITER (international thermonuclear experimental reactor) the plasma state is monitored using the plasma core diagnostics CXRS (charge exchange recombination spectroscopy).The authors describe the thermal and mechanical design of the first mirror of the CXRS diagnostics. The components of the first mirror are exposed to high heat and neutron irradiation. The surface temperature will be 300 to 400 deg C. The misalignment tolerance is plus or minus 0.1 degree. The maximum mechanical stresses in the mirror have to be minimized. The design calculations use the finite element code ANSYS. The results indicate that the heat input from the plasma can be removed by the coolant flow. Further calculation shave to concern the brazed joints between mirror and cooling block.

  6. Post and core build-ups in crown and bridge abutments: Bio-mechanical advantages and disadvantages.

    Science.gov (United States)

    Mamoun, John

    2017-06-01

    Dentists often place post and core buildups on endodontically treated abutments for crown and bridge restorations. This article analyzes the bio-mechanical purposes, advantages and disadvantages of placing a core or a post and core in an endodontically treated tooth and reviews literature on post and core biomechanics. The author assesses the scientific rationale of the claim that the main purpose of a post is to retain a core, or the claim that posts weaken teeth. More likely, the main function of a post is to help prevent the abutment, on which a crown is cemented, from fracturing such that the abutment separates from the tooth root, at a fracture plane that is located approximately and theoretically at the level of the crown (or ferrule) margin. A post essentially improves the ferrule effect that is provided by the partial fixed denture prosthesis. This paper also explores the difference between bio-mechanical failures of crowns caused by lack of retention or excess taper, versus failures due to a sub-optimal ferrule effect in crown and bridge prostheses.

  7. Investigation on multilayer failure mechanism of RPV with a high temperature gradient from core meltdown scenario

    Energy Technology Data Exchange (ETDEWEB)

    Jianfeng, Mao, E-mail: jianfeng-mao@163.com [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Engineering Research Center of Process Equipment and Remanufacturing, Ministry of Education (China); Xiangqing, Li [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Shiyi, Bao, E-mail: bsy@zjut.edu.cn [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Engineering Research Center of Process Equipment and Remanufacturing, Ministry of Education (China); Lijia, Luo [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Zengliang, Gao [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Engineering Research Center of Process Equipment and Remanufacturing, Ministry of Education (China)

    2016-12-15

    Highlights: • The multilayer failure mechanism is investigated for RPV under CHF. • Failure time and location of RPV are predicted under various SA scenarios. • The structural behaviors are analyzed in depth for creep and plasticity. • The effect of internal pressure and temperature gradient is considered. • The structural integrity of RPV is secured within the required 72 creep hours. - Abstract: The Fukushima accident shows that in-vessel retention (IVR) of molten core debris has not been appropriately assessed, and a certain pressure (up to 8.0 MPa) still exists inside the reactor pressure vessel (RPV). In the traditional concept of IVR, the pressure is supposed to successfully be released, and the temperature distributed among the wall thickness is assumed to be uniform. However, this concept is seriously challenged by reality of Fukushima accident with regard to the existence of both internal pressure and high temperature gradient. Therefore, in order to make the IVR mitigation strategy succeed, the numerical investigation of the lower head behavior and its failure has been performed for several internal pressures under high temperature gradient. According to some requirements in severe accident (SA) management of RPV, it should be ensured that the IVR mitigation takes effect in preventing the failure of the structure within a period of 72 h. Subsequently, the failure time and location have to be predicted under the critical heat flux (CHF) loading condition for lower head, since the CHF is limit thermal boundary before the melt-through of RPV. In illustrating the so called ‘multilayer failure mechanism’, the structural behaviors of RPV are analyzed in terms of the stress, creep strain, deformation, damage on selected paths.

  8. Investigation on multilayer failure mechanism of RPV with a high temperature gradient from core meltdown scenario

    International Nuclear Information System (INIS)

    Jianfeng, Mao; Xiangqing, Li; Shiyi, Bao; Lijia, Luo; Zengliang, Gao

    2016-01-01

    Highlights: • The multilayer failure mechanism is investigated for RPV under CHF. • Failure time and location of RPV are predicted under various SA scenarios. • The structural behaviors are analyzed in depth for creep and plasticity. • The effect of internal pressure and temperature gradient is considered. • The structural integrity of RPV is secured within the required 72 creep hours. - Abstract: The Fukushima accident shows that in-vessel retention (IVR) of molten core debris has not been appropriately assessed, and a certain pressure (up to 8.0 MPa) still exists inside the reactor pressure vessel (RPV). In the traditional concept of IVR, the pressure is supposed to successfully be released, and the temperature distributed among the wall thickness is assumed to be uniform. However, this concept is seriously challenged by reality of Fukushima accident with regard to the existence of both internal pressure and high temperature gradient. Therefore, in order to make the IVR mitigation strategy succeed, the numerical investigation of the lower head behavior and its failure has been performed for several internal pressures under high temperature gradient. According to some requirements in severe accident (SA) management of RPV, it should be ensured that the IVR mitigation takes effect in preventing the failure of the structure within a period of 72 h. Subsequently, the failure time and location have to be predicted under the critical heat flux (CHF) loading condition for lower head, since the CHF is limit thermal boundary before the melt-through of RPV. In illustrating the so called ‘multilayer failure mechanism’, the structural behaviors of RPV are analyzed in terms of the stress, creep strain, deformation, damage on selected paths.

  9. Simulation of the PHEBUS FPT-1 experiment using MELCOR and exploration of the primary core degradation mechanism

    International Nuclear Information System (INIS)

    Wang, Jun; Corradini, Michael L.; Fu, Wen; Haskin, Troy; Zhang, Yapei; Tian, Wenxi; Su, Guanghui; Qiu, Suizheng

    2015-01-01

    Highlights: • Core degradation evaluation is an important process in risk analysis. • PHEBUS experiment was simulated using MELCOR. • The results confirm the validity of MELCOR’s simulation of the PHEBUS experiment. • These results are used to analyze the mode and behavior of core degradation. - Abstract: Core degradation evaluation of probability, progression and consequences of a core degradation accident is critical for evaluation of risk as well as its mitigation. However, research and modeling of severe accidents to date are limited, and their accuracy in predicting severe accident consequences is still insufficient. It is therefore important to explore the mechanisms of core degradation and to develop mitigation measures for severe accidents. PHEBUS FPT1 is a typical and classic core degradation experiment. MELCOR is a world famous severe accident analysis code developed by Sandia National Lab that has seen wide application, a broad user base, and a number of supporting experiments. The PHEBUS experiment was simulated using MELCOR in this paper. Experimental data on, thermal power and steam mass flow rates are used to determine average pressure, energy distribution, molten mass, temperature of the fuel, and hydrogen generation. Data from the PHEBUS experiment and Cho’s calculations are used to compare the average pressure, several fuel temperatures and the hydrogen generation rate. The results confirm the validity of MELCOR’s simulation of the PHEBUS experiment. The temperature distribution of the core is provided. These results are used to determine the mode and behavior of core degradation with the intent of building a foundation for further research

  10. Mechanical behavior of a fast reactor core: Application of the 3D codes to SUPER PHENIX 1

    International Nuclear Information System (INIS)

    Bernard, A.; Masoni, P.; Dorsselaere, J.P. van

    1983-01-01

    The series of the 3-dimensional mechanical codes of a fast reactor core was used for the first time within the framework of a design study of an industrial reactor: SUPER-PHENIX 1. These codes are the following ones: - ARGOH which calculates the behavior of an isolated subassembly. - HARMONIE which calculates the core mechanical equilibrium - TRACAR which yields a graphic visualization of HARMONIE results, and calculates the handling forces and support reactions - HARMOREA which calculates the reactivity variations between given equilibrium states (for instance: pads effect and diagrid effect); now at the end of its development. The calculations were performed on 1/3 of the SPX1 core. Their purpose is double: - on the one hand, to check design criteria, and provide the loadings for the subassembly mechanical design studies; on the other hand, to evaluate the reactivity effects, related to the horizontal core deformations, and useful for operation and safety studies. The results of these calculations showed that the design criteria were verified for the contractual lifetime of the subassemblies. (orig.)

  11. Discussion on Microwave-Matter Interaction Mechanisms by In Situ Observation of "Core-Shell" Microstructure during Microwave Sintering.

    Science.gov (United States)

    Liu, Wenchao; Xu, Feng; Li, Yongcun; Hu, Xiaofang; Dong, Bo; Xiao, Yu

    2016-02-23

    This research aims to deepen the understanding of the interaction mechanisms between microwave and matter in a metal-ceramic system based on in situ synchrotron radiation computed tomography. A special internal "core-shell" microstructure was discovered for the first time and used as an indicator for the interaction mechanisms between microwave and matter. Firstly, it was proved that the microwave magnetic field acted on metal particles by way of inducing an eddy current in the surface of the metal particles, which led to the formation of a "core-shell" microstructure in the metal particles. On this basis, it was proposed that the ceramic particles could change the microwave field and open a way for the microwave, thereby leading to selective heating in the region around the ceramic particles, which was verified by the fact that all the "core-shell" microstructure was located around ceramic particles. Furthermore, it was indicated that the ceramic particles would gather the microwaves, and might lead to local heating in the metal-ceramic contact region. The focusing of the microwave was proved by the quantitative analysis of the evolution rate of the "core-shell" microstructure in a different region. This study will help to reveal the microwave-matter interaction mechanisms during microwave sintering.

  12. Pipe restraints for nuclear power plants

    International Nuclear Information System (INIS)

    Keever, R.E.; Broman, R.; Shevekov, S.

    1976-01-01

    A pipe restraint for nuclear power plants in which a support member is anchored on supporting surface is described. Formed in the support member is a semicylindrical wall. Seated on the semicylindrical wall is a ring-shaped pipe restrainer that has an inner cylindrical wall. The inner cylindrical wall of the pipe restrainer encircles the pressurized pipe. In a modification of the pipe restraint, an arched-shaped pipe restrainer is disposed to overlie a pressurized pipe. The ends of the arch-shaped pipe restrainer are fixed to support members, which are anchored in concrete or to a supporting surface. A strap depends from the arch-shaped pipe restrainer. The pressurized pipe is supported by the depending strap

  13. Pipeline dynamics subject to restraints with clearance

    International Nuclear Information System (INIS)

    Loula, A.F.D.; Guerreiro, J.N.C.

    1980-12-01

    The principle of virtual works at its incremental form, is utilized for the formulation of flat pipeline vibration problems, of elastic-plastic behavior, submitted to restraints with clearance (also with elastic-plastic behavior) and with viscous damping. The possibility of uniform movement of the support, that simulates the seismic action is also considered. The finite element method and an integration time algorithm, are utilized for the problem resolution. Some examples ilustrate the application of the development program. (Author) [pt

  14. Financial Restraints in the South Korean Miracle

    OpenAIRE

    Panicos O Demetriades; Kul B Luintel

    2000-01-01

    We provide novel empirical evidence on the effects of financial restraints on South Korean financial development. The evidence is linked to a simple model of the Korean banking system that encapsulates its cartelised nature, which predicts a positive association between financial development and (i) the degree of state control over the banking system, (ii) mild repression of lending rates. The model also predicts that in the presence of lending rate controls, increases in the level of the adm...

  15. Vortex induced vibrations in gapped restrainted pipes

    International Nuclear Information System (INIS)

    Veloso, P. de A.A.; Loula, A.F.D.

    1984-01-01

    The vortex induced vibration problem of gapped restrained piping is solved numerically. The model proposed by Skop-Griffin is used to describe the pipe-fluid interaction. The variational formulation is obtained modeling the gapped restraints as non-linear elastic springs. The regularized problem is solved using a finite element discretization for the spatial domain. In the time domain a finite difference discretization is used for the lift coefficient equatin and a Newmark discretization for the equation of motion. (Author) [pt

  16. Gold Mine or Minefield: Understanding Russian Law on Vertical Restraints

    Directory of Open Access Journals (Sweden)

    Valentina Rucker

    2014-01-01

    Full Text Available While the Russian Federation represents a significant opportunity for growth, that opportunity is coupled with serious risks. As it relates to managing product distribution, Russian vertical restraint law remains significantly more restrictive than that of the U.S. and, since unless a company is fully integrated, it must manage its distribution system by way of vertical agreements, presents a large problem for businesses seeking to conduct business in Russia. While Russia has made significant steps in the right direction, the lack of consistent application of economic analysis to evaluation of vertical restraints leaves companies exposed. Further, the sometimes inconsistent application of the laws also makes it hard to predict how any particular vertical agreement would be evaluated. Neither American nor Russian antitrust laws establish a list of possible vertical restraints. Thus, there is no exhaustive guidance regarding how these restraints should be treated. U.S. antitrust laws, however, generally place all vertical restraints into one of two categories, intrabrand restraints and interbrand restraints. Intrabrand restraints are those that restrain the downstream firm’s freedom with regard to the resale of the product at issue (distribution restrictions. Interbrand restraints are those that restrict a downstream or upstream firm’s freedom to deal with competitors of the firm imposing the restraint (interbrand restrictions. It should be noted that Russian law does not make this distinction.

  17. Measurement of Dietary Restraint: Validity Tests of Four Questionnaires

    Science.gov (United States)

    Williamson, Donald A.; Martin, Corby K.; York-Crowe, Emily; Anton, Stephen D.; Redman, Leanne M.; Han, Hongmei; Ravussin, Eric

    2007-01-01

    This study tested the validity of four measures of dietary restraint: Dutch Eating Behavior Questionnaire, Eating Inventory (EI), Revised Restraint Scale (RS), and the Current Dieting Questionnaire. Dietary restraint has been implicated as a determinant of overeating and binge eating. Conflicting findings have been attributed to different methods for measuring dietary restraint. The validity of four self-report measures of dietary restraint and dieting behavior was tested using: 1) factor analysis, 2) changes in dietary restraint in a randomized controlled trial of different methods to achieve calorie restriction, and 3) correlation of changes in dietary restraint with an objective measure of energy balance, calculated from the changes in fat mass and fat-free mass over a six-month dietary intervention. Scores from all four questionnaires, measured at baseline, formed a dietary restraint factor, but the RS also loaded on a binge eating factor. Based on change scores, the EI Restraint scale was the only measure that correlated significantly with energy balance expressed as a percentage of energy require d for weight maintenance. These findings suggest that that, of the four questionnaires tested, the EI Restraint scale was the most valid measure of the intent to diet and actual caloric restriction. PMID:17101191

  18. Gold Mine or Minefield: Understanding Russian Law on Vertical Restraints

    Directory of Open Access Journals (Sweden)

    Valentina Rucker

    2015-02-01

    Full Text Available While the Russian Federation represents a significant opportunity for growth, that opportunity is coupled with serious risks. As it relates to managing product distribution, Russian vertical restraint law remains significantly more restrictive than that of the U.S. and, since unless a company is fully integrated, it must manage its distribution system by way of vertical agreements, presents a large problem for businesses seeking to conduct business in Russia. While Russia has made significant steps in the right direction, the lack of consistent application of economic analysis to evaluation of vertical restraints leaves companies exposed. Further, the sometimes inconsistent application of the laws also makes it hard to predict how any particular vertical agreement would be evaluated. Neither American nor Russian antitrust laws establish a list of possible vertical restraints. Thus, there is no exhaustive guidance regarding how these restraints should be treated. U.S. antitrust laws, however, generally place all vertical restraints into one of two categories, intrabrand restraints and interbrand restraints. Intrabrand restraints are those that restrain the downstream firm’s freedom with regard to the resale of the product at issue (distribution restrictions. Interbrand restraints are those that restrict a downstream or upstream firm’s freedom to deal with competitors of the firm imposing the restraint (interbrand restrictions. It should be noted that Russian law does not make this distinction.

  19. Emotional eating and routine restraint scores are associated with activity in brain regions involved in urge and self-control.

    Science.gov (United States)

    Wood, Samantha M W; Schembre, Susan M; He, Qinghua; Engelmann, Jeffrey M; Ames, Susan L; Bechara, Antoine

    2016-10-15

    Researchers have proposed a variety of behavioral traits that may lead to weight gain and obesity; however, little is known about the neurocognitive mechanisms underlying these weight-related eating behaviors. In this study, we measured activation of reward circuitry during a task requiring response and inhibition to food stimuli. We assessed participants' emotional eating, external eating, and two subscales of dietary restraint-routine restraint and compensatory restraint-using the Weight-Related Eating Questionnaire. For routine restraint, we found positive associations with activation in the insula, dorsolateral prefrontal cortex, anterior cingulate cortex, orbitofrontal cortex and ventromedial prefrontal cortex in response to high-calorie versus low-calorie foods. For emotional eating, we found positive associations with insula and dorsolateral prefrontal cortex activation in response to high-calorie versus low-calorie foods. We also found positive associations between emotional eating and dorsolateral prefrontal cortex activation in response to approach versus inhibition towards high-calorie foods. Thus, our results demonstrate an increase in activation across brain regions related to self-control and urges in response to high-calorie food associated with both emotional eating and routine restraint. Overall, these results support the construct validity of both emotional eating and routine restraint and provide preliminary evidence that these subscales have similar neural correlates. Copyright © 2016 Elsevier Inc. All rights reserved.

  20. Humidity effects on soluble core mechanical and thermal properties (polyvinyl alcohol/microballoon composite) type CG extendospheres, volume 2

    Science.gov (United States)

    1993-01-01

    This document constitutes the final report for the study of humidity effects and loading rate on soluble core (PVA/MB composite material) mechanical and thermal properties under Contract No. 100345. This report describes test results procedures employed, and any unusual occurrences or specific observations associated with this test program. The primary objective of this work was to determine if cured soluble core filler material regains its tensile and compressive strength after exposure to high humidity conditions and following a drying cycle. Secondary objectives include measurements of tensile and compressive modulus, and Poisson's ratio, and coefficient of thermal expansion (CTE) for various moisture exposure states. A third objective was to compare the mechanical and thermal properties of the composite using 'SG' and 'CG' type extendospheres. The proposed facility for the manufacture of soluble cores at the Yellow Creek site incorporates no capability for the control of humidity. Recent physical property tests performed with the soluble core filler material showed that prolonged exposure to high humidity significantly degradates in strength. The purpose of these tests is to determine if the product, process or facility designs require modification to avoid imparting a high risk condition to the ASRM.

  1. Study of the mechanisms for the emergency cooling of the core of the Radioisotope Producing Reator (RPR)

    International Nuclear Information System (INIS)

    Lacerda, F.C.

    1987-01-01

    The mechanisms for the emergency cooling of the core of the Radioisotope Producing Reactor (R.P.R.) are studied, in particular the thermal-hydraulic behaviour of the coolant after reactor shut-down. The coolant operates bd convection, and flows downward through the core passing into beel-shaped plenum that encloses the core and proceeding across the primary cooling loop. When the reactor is shut-down, the coolant flow undergoes a transient period until the steady state of natural convection is reached, after which the coolant flows upwards from the lower plenum. A plocking valve will be installed at the exit of the lower plenum, which will automatically shut in case of an accident that will involve the loss of flow in the primary circuit. The present work aims at evaluating the contribution of natural convection by natural recirculation in the core when the blocking valve is close, and via the external coolant circuit when the blocking valve is open. In particular, we study the natural self-regulating mechanisms of extraction of the heat generated by the fission product after reactor shut-down. (author) [pt

  2. Ice-sheet flow conditions deduced from mechanical tests of ice core

    DEFF Research Database (Denmark)

    Miyamoto, Atsushi; Narita, Hideki; Hondoh, Takeo

    1999-01-01

    Uniaxial compression tests were performed on samples of the Greenland Ice Core Project (GRIP) deep ice core, both in the field and later in a cold-room laboratory, in order to understand the ice-flow behavior of large ice sheets. Experiments were conducted under conditions of constant strain rate....... It was revealed that cloudy bands affect ice-deformation processes, but the details remain unclear. Udgivelsesdato: June......Uniaxial compression tests were performed on samples of the Greenland Ice Core Project (GRIP) deep ice core, both in the field and later in a cold-room laboratory, in order to understand the ice-flow behavior of large ice sheets. Experiments were conducted under conditions of constant strain rate......-core samples with basal planes parallel to the horizontal plane of the ice sheet. The ice-flow enhancement factors show a gradual increase with depth down to approximately 2000 m. These results can be interpreted in terms of an increase in the fourth-order Schmid factor. Below 2000 m depth, the flow...

  3. Reactor core and passive safety systems descriptions of a next generation pressure tube reactor - mechanical aspects

    Energy Technology Data Exchange (ETDEWEB)

    Yetisir, M.; Gaudet, M.; Rhodes, D.; Hamilton, H.; Pencer, J. [Atomic Energy of Canada Limited, Chalk River, ON (Canada)

    2014-07-01

    Canada has been developing a channel-type supercritical water-cooled nuclear reactor concept, often called the Canadian SCWR. The objective of this reactor concept is to meet the technology goals of the Generation IV International Forum (GIF) for the next generation nuclear reactor development, which include enhanced safety features (inherent safe operation and deploying passive safety features), improved resource utilization, sustainable fuel cycle, and greater proliferation resistance than Generation III nuclear reactors. The Canadian SCWR core concept consists of a high-pressure inlet plenum, a separate low-pressure heavy water moderator contained in a calandria vessel, and 336 pressure tubes surrounded by the moderator. The reactor uses supercritical water as a coolant, and a direct steam power cycle to generate electricity. The reactor concept incorporates advanced safety features such as passive core cooling, long-term decay heat rejection to the environment and fuel melt prevention via passive moderator cooling. These features significantly reduce core damage frequency relative to existing nuclear reactors. This paper presents a description of the design concepts for the Canadian SCWR core, reactor building layout and the plant layout. Passive safety concepts are also described that address containment and core cooling following a loss-of coolant accident, as well as long term reactor heat removal at station blackout conditions. (author)

  4. Cell-like pressure sensors reveal increase of mechanical stress towards the core of multicellular spheroids under compression.

    Science.gov (United States)

    Dolega, M E; Delarue, M; Ingremeau, F; Prost, J; Delon, A; Cappello, G

    2017-01-27

    The surrounding microenvironment limits tumour expansion, imposing a compressive stress on the tumour, but little is known how pressure propagates inside the tumour. Here we present non-destructive cell-like microsensors to locally quantify mechanical stress distribution in three-dimensional tissue. Our sensors are polyacrylamide microbeads of well-defined elasticity, size and surface coating to enable internalization within the cellular environment. By isotropically compressing multicellular spheroids (MCS), which are spherical aggregates of cells mimicking a tumour, we show that the pressure is transmitted in a non-trivial manner inside the MCS, with a pressure rise towards the core. This observed pressure profile is explained by the anisotropic arrangement of cells and our results suggest that such anisotropy alone is sufficient to explain the pressure rise inside MCS composed of a single cell type. Furthermore, such pressure distribution suggests a direct link between increased mechanical stress and previously observed lack of proliferation within the spheroids core.

  5. Mechanical behavior of a fast reactor core application of 3D codes to SUPER-PHENIX 1 and parametric studies

    International Nuclear Information System (INIS)

    Bernard, A.; Dorsselaere, J.P. van

    1984-01-01

    This paper presents the SPX1 project calculations, performed on 1/3 core with the aid of the series of 3D codes described in Session 2. The main criteria, related to contact forces, head bowings and handling forces, are fulfilled. Some parametric studies on the mechanical equilibrium are also presented. The main parameters are: the axial pad level, the subassembly stiffness and the pad local stiffness. (author)

  6. Core-firm Based View on the Mechanism of Constructing a Corporate Innovation Ecosystem

    DEFF Research Database (Denmark)

    Jiang, Shimei; Wang, Ziyuan; Hu, Yimei

    2016-01-01

    The fierce transformation of the competitive status of business world in the 21st century has urged the innovation activities turned from mechanistic and deterministic to ecological and organic. The study firstly defines the concept of core firm based on reviewing existing corporate innovation...... constructing a corporate innovation ecosystem through building up an innovation platform that include multi-level collaborative relationships based on different technologies; while at the same time integrating non-technological issues such as strategy, culture, management, organization, institution and market....... This research complements and extends literature on corporate innovation ecosystem, and provides implications to innovative companies on constructing a core firm based innovation ecosystem....

  7. Mechanical and Physical Properties of Low Density Kenaf Core Particleboards Bonded with Different Resins

    OpenAIRE

    Mohamad Jani Saad; Izran Kamal

    2012-01-01

    Single layer kenaf (Hibiscus cannabinus) core particleboards bonded with urea formaldehyde (UF), phenol formaldehyde (PF) and polymeric 4,4-methyl phenylmethane di-isocyanate (PMDI) resins were manufactured. The boards were fabricated with three different densities i.e 350 kg/m3, 450 kg/m3 and 550 kg/m3. Each type of the resin used was sprayed at three different resin loadings on the kenaf core particles. The boards produced was evaluated for its modulus of rupture (MOR), modulus of elasticit...

  8. Quantum mechanics/molecular mechanics modeling of photoelectron spectra: the carbon 1s core-electron binding energies of ethanol-water solutions.

    Science.gov (United States)

    Löytynoja, T; Niskanen, J; Jänkälä, K; Vahtras, O; Rinkevicius, Z; Ågren, H

    2014-11-20

    Using ethanol-water solutions as illustration, we demonstrate the capability of the hybrid quantum mechanics/molecular mechanics (QM/MM) paradigm to simulate core photoelectron spectroscopy: the binding energies and the chemical shifts. An integrated approach with QM/MM binding energy calculations coupled to preceding molecular dynamics sampling is adopted to generate binding energies averaged over the solute-solvent configurations available at a particular temperature and pressure and thus allowing for a statistical assessment with confidence levels for the final binding energies. The results are analyzed in terms of the contributions in the molecular mechanics model-electrostatic, polarization, and van der Waals-with atom or bond granulation of the corresponding MM charge and polarizability force-fields. The role of extramolecular charge transfer screening of the core-hole and explicit hydrogen bonding is studied by extending the QM core to cover the first solvation shell. The results are compared to those obtained from pure electrostatic and polarizable continuum models. Particularly, the dependence of the carbon 1s binding energies with respect to the ethanol concentration is studied. Our results indicate that QM/MM can be used as an all-encompassing model to study photoelectron binding energies and chemical shifts in solvent environments.

  9. Organizational Routines as Coupling Mechanisms: Policy, School Administration, and the Technical Core

    Science.gov (United States)

    Spillane, James P.; Parise, Leigh Mesler; Sherer, Jennifer Zoltners

    2011-01-01

    The institutional environment of America's schools has changed substantially as government regulation has focused increasingly on the core technical work of schools--instruction. The authors explore the school administrative response to this changing environment, describing how government regulation becomes embodied in the formal structure of four…

  10. Energy and generating mechanism of a subsurface, cold core eddy in the Bay of Bengal

    Digital Repository Service at National Institute of Oceanography (India)

    PrasannaKumar, S.; Babu, M.T.; Rao, D.P.

    Computation of available potential energy (APE) of a recently observed cold core, subsurface eddy (centered at 17 degrees 40'N and 85 degrees 19'E) in the Bay of Bengal revealed that the energy maxima associated with the eddy was of the order of 1...

  11. Restraint methods for radiography in dogs and cats

    International Nuclear Information System (INIS)

    Scrivani, P.V.; Bednarski, R.M.; Myer, C.W.; Dykes, N.L.

    1996-01-01

    Excellent patient restraint techniques are necessary to produce high-quality diagnostic images during survey and contrast radiography and ultrasonography. Use of non manual physical restraint (i.e., devices to hold the patient in position) helps reduce the exposure of veterinary personnel to radiation. Exposure of personnel to radiation should be kept as low as reasonably achievable. Usually, this involves taking the radiograph when no personnel are present in the room. Some procedures, however, require the presence of the veterinarian. No personnel should ever put any part of their bodies in the path of the x-ray beam. Protective gear must be worn. Physical restraint can be facilitated by chemical restraint, which varies from minimal sedation to general anesthesia. Appropriate chemical restraint for radiography is the minimum amount of sedation required for the efficient and safe completion of the radiographic examination. Chemical restraint techniques vary according to the patient's physical status, the type of examination, and the skill of the examiner in non manual restraint techniques. This article describes techniques for non manual restraint and protocols for chemical restraint for dogs and cats

  12. FBR core mock-up RAPSODIE I - experimental analysis

    International Nuclear Information System (INIS)

    Brochard, D.; Buland, P.; Gantenbein, F.

    1990-01-01

    The main phenomena which influence the LMFBR core response to a seismic excitation are the fluid structure interaction and the impacts between subassemblies. To study the core behaviour, seismic tests have been performed on the core mock-up RAPSODIE with and without fluid and restraint ring and for different levels of excitation. This paper summarizes the results of these tests. (author)

  13. AT89S52 Microcontroller Based A Speed Restraint Equipment for Motorcycle

    Directory of Open Access Journals (Sweden)

    Ikhsan hidayat

    2009-08-01

    Full Text Available Security riding is very important in the aspects of traffic. One of the main factors of traffic accidents is high speed. Therefore, it is required a speed restraint equipment for pressing the number of accidents. The car speed restraint system is available in the market, but on a motorcycle is not available yet. This paper presents a design of speed restraint equipment for motorcycle that safe for users, and is expected to reduce traffic accident. The Main idea this speed restriction is cutting off the flow of electrical signals from the pulser (the time ignition trigger sensor to the CDI for 1 second. The cutting Signal with mechanical relays controlled by microcontroller AT89S52 using the on-off algorithm. Speed sensor use optocoupler is used to detect the number of rounds wheel motorcycle. If a result of measurement is more than the speed setpoint, microcontroler make a decission to cut motorcycle ignition signal. Results of this research is a prototype speed restraint shown that it able to process data from the measurement of the speed limit on the speed of a motorcycle. This prototype safe for all users and accordance with the set value and the level of success is above 90% for speed of 10 km/hr to 40 km/hr.

  14. The restraint bias: how the illusion of self-restraint promotes impulsive behavior

    NARCIS (Netherlands)

    Nordgren, L.F.; van Harreveld, F.; van der Pligt, J.

    2009-01-01

    Four studies examined how impulse-control beliefs—beliefs regarding one's ability to regulate visceral impulses, such as hunger, drug craving, and sexual arousal—influence the self-control process. The findings provide evidence for a restraint bias: a tendency for people to overestimate their

  15. Circumstellar Disks and Outflows in Turbulent Molecular Cloud Cores: Possible Formation Mechanism for Misaligned Systems

    Energy Technology Data Exchange (ETDEWEB)

    Matsumoto, Tomoaki [Faculty of Sustainability Studies, Hosei University, Fujimi, Chiyoda-ku, Tokyo 102-8160 (Japan); Machida, Masahiro N. [Department of Earth and Planetary Sciences, Kyushu University, Fukuoka 812-8581 (Japan); Inutsuka, Shu-ichiro, E-mail: matsu@hosei.ac.jp [Department of Physics, Nagoya University, Chikusa-ku, Nagoya 464-8602 (Japan)

    2017-04-10

    We investigate the formation of circumstellar disks and outflows subsequent to the collapse of molecular cloud cores with the magnetic field and turbulence. Numerical simulations are performed by using an adaptive mesh refinement to follow the evolution up to ∼1000 years after the formation of a protostar. In the simulations, circumstellar disks are formed around the protostars; those in magnetized models are considerably smaller than those in nonmagnetized models, but their size increases with time. The models with stronger magnetic fields tend to produce smaller disks. During evolution in the magnetized models, the mass ratios of a disk to a protostar is approximately constant at ∼1%–10%. The circumstellar disks are aligned according to their angular momentum, and the outflows accelerate along the magnetic field on the 10–100 au scale; this produces a disk that is misaligned with the outflow. The outflows are classified into two types: a magnetocentrifugal wind and a spiral flow. In the latter, because of the geometry, the axis of rotation is misaligned with the magnetic field. The magnetic field has an internal structure in the cloud cores, which also causes misalignment between the outflows and the magnetic field on the scale of the cloud core. The distribution of the angular momentum vectors in a core also has a non-monotonic internal structure. This should create a time-dependent accretion of angular momenta onto the circumstellar disk. Therefore, the circumstellar disks are expected to change their orientation as well as their sizes in the long-term evolutions.

  16. Quantum mechanics capacitance molecular mechanics modeling of core-electron binding energies of methanol and methyl nitrite on Ag(111) surface.

    Science.gov (United States)

    Löytynoja, T; Li, X; Jänkälä, K; Rinkevicius, Z; Ågren, H

    2016-07-14

    We study a newly devised quantum mechanics capacitance molecular mechanics (QMCMM) method for the calculation of core-electron binding energies in the case of molecules adsorbed on metal surfaces. This yet untested methodology is applied to systems with monolayer of methanol/methyl nitrite on an Ag(111) surface at 100 K temperature. It was found out that the studied C, N, and O 1s core-hole energies converge very slowly as a function of the radius of the metallic cluster, which was ascribed to build up of positive charge on the edge of the Ag slab. Further analysis revealed that an extrapolation process can be used to obtain binding energies that deviated less than 0.5 eV against experiments, except in the case of methanol O 1s where the difference was as large as 1.8 eV. Additional QM-cluster calculations suggest that the latter error can be connected to the lack of charge transfer over the QM-CMM boundary. Thus, the results indicate that the QMCMM and QM-cluster methods can complement each other in a holistic picture of molecule-adsorbate core-ionization studies, where all types of intermolecular interactions are considered.

  17. Restraint Use in Older Adults Receiving Home Care.

    Science.gov (United States)

    Scheepmans, Kristien; Dierckx de Casterlé, Bernadette; Paquay, Louis; Van Gansbeke, Hendrik; Milisen, Koen

    2017-08-01

    To determine the prevalence, types, frequency, and duration of restraint use in older adults receiving home nursing care and to determine factors involved in the decision-making process for restraint use and application. Cross-sectional survey of restraint use in older adults receiving home care completed by primary care nurses. Homes of older adults receiving care from a home nursing organization in Belgium. Randomized sample of older adults receiving home care (N = 6,397; mean age 80.6; 66.8% female). For each participant, nurses completed an investigator-constructed and -validated questionnaire collecting information demographic, clinical, and behavioral characteristics and aspects of restraint use. A broad definition of restraint was used that includes a range of restrictive actions. Restraints were used in 24.7% of the participants, mostly on a daily basis (85%) and often for a long period (54.5%, 24 h/d). The most common reason for restraint use was safety (50.2%). Other reasons were that the individual wanted to remain at home longer, which necessitated the use of restraints (18.2%) and to provide respite for the informal caregiver (8.6%). The latter played an important role in the decision and application process. The physician was less involved in the process. In 64.5% of cases, there was no evaluation after restraint use was initiated. Use of restraints is common in older adults receiving home care nursing in Belgium. These results contribute to a better understanding of the complexity of use of restraints in home care, a situation that may be even more complex than in nursing homes and acute hospital settings. © 2017, Copyright the Authors Journal compilation © 2017, The American Geriatrics Society.

  18. Universal core model for multiple-gate field-effect transistors with short channel and quantum mechanical effects

    Science.gov (United States)

    Shin, Yong Hyeon; Bae, Min Soo; Park, Chuntaek; Park, Joung Won; Park, Hyunwoo; Lee, Yong Ju; Yun, Ilgu

    2018-06-01

    A universal core model for multiple-gate (MG) field-effect transistors (FETs) with short channel effects (SCEs) and quantum mechanical effects (QMEs) is proposed. By using a Young’s approximation based solution for one-dimensional Poisson’s equations the total inversion charge density (Q inv ) in the channel is modeled for double-gate (DG) and surrounding-gate SG (SG) FETs, following which a universal charge model is derived based on the similarity of the solutions, including for quadruple-gate (QG) FETs. For triple-gate (TG) FETs, the average of DG and QG FETs are used. A SCEs model is also proposed considering the potential difference between the channel’s surface and center. Finally, a QMEs model for MG FETs is developed using the quantum correction compact model. The proposed universal core model is validated on commercially available three-dimensional ATLAS numerical simulations.

  19. Monitoring the mechanical vibration of in-core detector tubes and fuel channels via ICFD noise analysis

    International Nuclear Information System (INIS)

    Glockler, O.; Cooke, D.F.; Czuppon, G.J.; Kapoor, K.K.

    2000-01-01

    Vibrations of core internals are regularly monitored in the CANDU nuclear generating stations of Ontario Power Generation (OPG) via the noise analysis of in-core flux detectors (ICFDs). Voltage signals of standard station instrumentation are recorded by portable multi-channel high-speed high-resolution data acquisition systems, then statistical parameters are derived from the multi-channel time series measurements. Reactor noise analysis is a non-intrusive statistical technique regularly used in system surveillance, diagnostics and in actual operational I and C problems. It utilizes the dynamic information carried by the small fluctuations (noise) of station signals measured around their mean values during steady-state operation. The present paper discusses specific results related to the flow-induced mechanical vibrations of detector tubes and fuel channels. (author)

  20. Rearrangement of a polar core provides a conserved mechanism for constitutive activation of class B G protein-coupled receptors

    Science.gov (United States)

    Yin, Yanting; de Waal, Parker W.; He, Yuanzheng; Zhao, Li-Hua; Yang, Dehua; Cai, Xiaoqing; Jiang, Yi; Melcher, Karsten; Wang, Ming-Wei; Xu, H. Eric

    2017-01-01

    The glucagon receptor (GCGR) belongs to the secretin-like (class B) family of G protein-coupled receptors (GPCRs) and is activated by the peptide hormone glucagon. The structures of an activated class B GPCR have remained unsolved, preventing a mechanistic understanding of how these receptors are activated. Using a combination of structural modeling and mutagenesis studies, we present here two modes of ligand-independent activation of GCGR. First, we identified a GCGR-specific hydrophobic lock comprising Met-338 and Phe-345 within the IC3 loop and transmembrane helix 6 (TM6) and found that this lock stabilizes the TM6 helix in the inactive conformation. Disruption of this hydrophobic lock led to constitutive G protein and arrestin signaling. Second, we discovered a polar core comprising conserved residues in TM2, TM3, TM6, and TM7, and mutations that disrupt this polar core led to constitutive GCGR activity. On the basis of these results, we propose a mechanistic model of GCGR activation in which TM6 is held in an inactive conformation by the conserved polar core and the hydrophobic lock. Mutations that disrupt these inhibitory elements allow TM6 to swing outward to adopt an active TM6 conformation similar to that of the canonical β2-adrenergic receptor complexed with G protein and to that of rhodopsin complexed with arrestin. Importantly, mutations in the corresponding polar core of several other members of class B GPCRs, including PTH1R, PAC1R, VIP1R, and CRFR1, also induce constitutive G protein signaling, suggesting that the rearrangement of the polar core is a conserved mechanism for class B GPCR activation. PMID:28356352

  1. Rearrangement of a polar core provides a conserved mechanism for constitutive activation of class B G protein-coupled receptors.

    Science.gov (United States)

    Yin, Yanting; de Waal, Parker W; He, Yuanzheng; Zhao, Li-Hua; Yang, Dehua; Cai, Xiaoqing; Jiang, Yi; Melcher, Karsten; Wang, Ming-Wei; Xu, H Eric

    2017-06-16

    The glucagon receptor (GCGR) belongs to the secretin-like (class B) family of G protein-coupled receptors (GPCRs) and is activated by the peptide hormone glucagon. The structures of an activated class B GPCR have remained unsolved, preventing a mechanistic understanding of how these receptors are activated. Using a combination of structural modeling and mutagenesis studies, we present here two modes of ligand-independent activation of GCGR. First, we identified a GCGR-specific hydrophobic lock comprising Met-338 and Phe-345 within the IC3 loop and transmembrane helix 6 (TM6) and found that this lock stabilizes the TM6 helix in the inactive conformation. Disruption of this hydrophobic lock led to constitutive G protein and arrestin signaling. Second, we discovered a polar core comprising conserved residues in TM2, TM3, TM6, and TM7, and mutations that disrupt this polar core led to constitutive GCGR activity. On the basis of these results, we propose a mechanistic model of GCGR activation in which TM6 is held in an inactive conformation by the conserved polar core and the hydrophobic lock. Mutations that disrupt these inhibitory elements allow TM6 to swing outward to adopt an active TM6 conformation similar to that of the canonical β 2 -adrenergic receptor complexed with G protein and to that of rhodopsin complexed with arrestin. Importantly, mutations in the corresponding polar core of several other members of class B GPCRs, including PTH1R, PAC1R, VIP1R, and CRFR1, also induce constitutive G protein signaling, suggesting that the rearrangement of the polar core is a conserved mechanism for class B GPCR activation. © 2017 by The American Society for Biochemistry and Molecular Biology, Inc.

  2. Estimation of the mechanical effects of a core disruptive accident on a LMFBR

    International Nuclear Information System (INIS)

    Robbe, M.F.; Lepareux, M.; Treille, E.

    2001-01-01

    In case of a Hypothetical Core Disruptive Accident (HCDA) in a Liquid Metal Reactor, the interaction between fuel and liquid sodium creates a high pressure gas bubble in the core. The violent expansion of this bubble loads the vessel and the internal structures, whose deformation is important. In order to demonstrate the CASTEM-PLEXUS capability to predict the behaviour of real reactors], axisymmetric computations of the MARA series were confronted with the experimental results. The computations performed at the beginning of the years 90 showed a rather good agreement between the experimental and computed results for the MARA 8 and MARA 10 tests even if there were some discrepancies which might be eliminated by increasing the fineness of the mesh. On the contrary, the prediction of the MARS structure displacements and strains was overestimated. This conservatism was supposed to come from the fact that several MARS non axisymmetric structures like core elements, pumps and heat exchangers were not represented in the CASTEM-PLEXUS model. These structures, acting as porous barriers, had a protective effect on the containment by absorbing energy and slowing down the fluid impacting the containment. For these reasons, we developed in CASTEM-PLEXUS a new HCDA constitutive law taking into account the presence of the internal structures (without meshing them) by means of an equivalent porosity method and we simulated the MARS test another time with the new HCDA constitutive law. This paper presents the numerical results relative to the structure behaviour during the accident. The results are described through the evolution of several variables versus time: deformed shape of the structures and the mesh, displacements, stresses and plastic strains. (author)

  3. Alcohol, Appetite and Loss of Restraint.

    Science.gov (United States)

    Caton, Samantha J; Nolan, Laurence J; Hetherington, Marion M

    2015-03-01

    Alcoholic beverages have long been associated with feasts, celebration and marking special events. Today, it is commonplace to consume alcoholic beverages before, with and/or after a meal. Alcohol provides additional pleasure to the meal and enhances appetite. However, consuming an alcoholic beverage with or before a meal is associated with poor short-term energy compensation; energy from alcohol is additive to total energy intake with the added property of stimulating further eating. Limiting alcohol intake is an obvious means to reduce total energy intake for those who wish to lose weight. However, dieters and restrained eaters drink more and report greater binge drinking than unrestrained eaters despite employing cognitive strategies to reduce their intake. Increased intake may be attributable to greater attentional bias to alcohol related cues as well as to food cues, since these are more salient to those limiting intake. Alcohol increases energy intake in dieters, in part due to abandonment of restraint (disinhibition) and consumption of forbidden items including alcohol exacerbates attempts to resist temptation. Paradoxically, links between binge drinking or increased drinking frequency to overweight and obesity may be mediated by dietary restraint. Efforts to limit food and alcohol intake for weight control appear to be unsuccessful and have the net effect of promoting overconsumption. The potential role of restrained eating in the association between alcohol, appetite and obesity has been overlooked by much of the current research and further investigation of this is therefore warranted.

  4. 75 FR 9613 - Draft NIJ Restraints Standard for Criminal Justice

    Science.gov (United States)

    2010-03-03

    ... DEPARTMENT OF JUSTICE Office of Justice Programs [OJP (NIJ) Docket No. 1512] Draft NIJ Restraints Standard for Criminal Justice AGENCY: National Institute of Justice, Office of Justice Programs, DOJ. ACTION: Notice of Draft NIJ Restraints Standard for Criminal Justice and Certification Program...

  5. Acute restraint stress induces hyperalgesia via non-adrenergic ...

    African Journals Online (AJOL)

    Analgesia or hyperalgesia has been reported to occur in animals under different stress conditions. This study examined the effect of acute restraint stress on nociception in rats. Acute restraint stress produced a time-dependant decrease in pain threshold; this hyperalgesia was not affected by prior administration of ...

  6. The relationship between restraints of trade and garden leave ...

    African Journals Online (AJOL)

    The relationship between restraints of trade and garden leave. ... Potchefstroom Electronic Law Journal/Potchefstroomse Elektroniese Regsblad ... The purpose of the article is to examine the relationship between a so-called "garden leave" clause and a post-termination restraint of trade clause in employment contracts, ...

  7. Continuous restraint control systems: safety improvement for various occupants

    NARCIS (Netherlands)

    Laan, E. van der; Jager, B. de; Veldpaus, F.; Steinbuch, M.; Nunen, E. van; Willemsen, D.

    2009-01-01

    Occupant safety can be significantly improved by continuous restraint control systems. These restraint systems adjust their configuration during the impact according to the actual operating conditions, such as occupant size, weight, occupant position, belt usage and crash severity. In this study,

  8. Ring waves as a mass transport mechanism in air-driven core-annular flows.

    Science.gov (United States)

    Camassa, Roberto; Forest, M Gregory; Lee, Long; Ogrosky, H Reed; Olander, Jeffrey

    2012-12-01

    Air-driven core-annular fluid flows occur in many situations, from lung airways to engineering applications. Here we study, experimentally and theoretically, flows where a viscous liquid film lining the inside of a tube is forced upwards against gravity by turbulent airflow up the center of the tube. We present results on the thickness and mean speed of the film and properties of the interfacial waves that develop from an instability of the air-liquid interface. We derive a long-wave asymptotic model and compare properties of its solutions with those of the experiments. Traveling wave solutions of this long-wave model exhibit evidence of different mass transport regimes: Past a certain threshold, sufficiently large-amplitude waves begin to trap cores of fluid which propagate upward at wave speeds. This theoretical result is then confirmed by a second set of experiments that show evidence of ring waves of annular fluid propagating over the underlying creeping flow. By tuning the parameters of the experiments, the strength of this phenomenon can be adjusted in a way that is predicted qualitatively by the model.

  9. Deep venous thrombosis and pulmonary embolism following physical restraint

    DEFF Research Database (Denmark)

    Laursen, S B; Jensen, T N; Bolwig, T

    2005-01-01

    . The literature on physical restraint, DVT, and PE was reviewed using a search of Medline and Psychinfo from 1966 to the present. RESULTS: Four other reported cases of DVT and PE were found in association with physically restrained patients. CONCLUSION: Risk of DVT and PE in association with immobilization during......OBJECTIVE: We describe a case of deep venous thrombosis (DVT) and pulmonary embolism (PE) following the use of physical restraint in a patient with a diagnosis of acute delusional psychotic disorder. METHOD: A new case report of DVT and PE associated with prolonged physical restraint is presented...... physical restraint may occur in spite of no pre-existing risk factors. Medical guidelines for the prevention of thrombosis following physical restraint are presented. Despite the absence of controlled trials of treatment effectiveness, the catastrophic outcome of DVT and PE warrants early and vigorous...

  10. Orthogonal Assessment of Biotherapeutic Glycosylation: A Case Study Correlating N-Glycan Core Afucosylation of Herceptin with Mechanism of Action.

    Science.gov (United States)

    Upton, Rosie; Bell, Leonard; Guy, Colin; Caldwell, Paul; Estdale, Sian; Barran, Perdita E; Firth, David

    2016-10-18

    In the development of therapeutic antibodies and biosimilars, an appropriate biopharmaceutical CMC control strategy that connects critical quality attributes with mechanism of action should enable product assessment at an early stage of development in order to mitigate risk. Here we demonstrate a new analytical workflow using trastuzumab which comprises "middle-up" analysis using a combination of IdeS and the endoglycosidases EndoS and EndoS2 to comprehensively map the glycan content. Enzymatic cleavage between the two N-acetyl glucosamine residues of the chitobiose core of N-glycans significantly simplifies the oligosaccharide component enabling facile distinction of GlcNAc from GlcNAc with core fucose. This approach facilitates quantitative determination of total Fc-glycan core-afucosylation, which was in turn correlated with receptor binding affinity by surface plasmon resonance and in vitro ADCC potency with a cell based bioassay. The strategy also quantifies Fc-glycan occupancy and the relative contribution from high mannose glycans.

  11. Prediction of mining conditions from bore core information: rock mechanics investigations in the Whybrow Seam at Wambo Colliery

    Energy Technology Data Exchange (ETDEWEB)

    Richmond, A.; Levers, R.; Smith, K.

    1979-12-01

    Rock mechanics investigations were conducted at Wambo Colliery as part of the series designed to study the stability of mining structures and obtain geomechanical properties. The roof and floor were drilled in order to obtain core for rock testing and samples of coal were collected to measure the coal properties. A successful overcoring of a CSIR strain cell was achieved to determine the absolute stress field. The core which was recovered was logged prior to laboratory testing to determine a C index (modified RQD index based on core fragmentation). This was used to estimate the in-situ strata properties from the laboratory results. The roof material was found to consist predominantly of a competent laminite. The Whybrow seam above the Cow Manure band had an average uniaxial strength of 26 MPa. The Cow Manure band was extremely weak with a strength of 1 MPa, while the coal below this band was much weaker than the upper section coal with a strength of 7 MPa. The floor strata was made up of competent carbonaceous siltstone and alternate bands of shale and sandstone. Finite element analyses indicate very stable roof, floor and rib, corresponding closely to the in-situ conditions.

  12. 3D Printed Auxetic Mechanical Metamaterial with Chiral Cells and Re-entrant Cores.

    Science.gov (United States)

    Jiang, Yunyao; Li, Yaning

    2018-02-05

    By combining the two basic deformation mechanisms for auxetic open-cell metamaterials, re-entrant angle and chirality, new hybrid chiral mechanical metamaterials are designed and fabricated via a multi-material 3D printer. Results from mechanical experiments on the 3D printed prototypes and systematic Finite Element (FE) simulations show that the new designs can achieve subsequential cell-opening mechanism under a very large range of overall strains (2.91%-52.6%). Also, the effective stiffness, the Poisson's ratio and the cell-opening rate of the new designs can be tuned in a wide range by tailoring the two independent geometric parameters: the cell size ratio [Formula: see text], and re-entrant angle θ. As an example application, a sequential particle release mechanism of the new designs was also systematically explored. This mechanism has potential application in drug delivery. The present new design concepts can be used to develop new multi-functional smart composites, sensors and/or actuators which are responsive to external load and/or environmental conditions.

  13. ARKAS: A three-dimensional finite element code for the analysis of core distortions and mechanical behaviour

    International Nuclear Information System (INIS)

    Nakagawa, M.

    1984-01-01

    Computer program ARKAS has been developed for the purpose of predicting core distortions and mechanical behaviour in a cluster of subassemblies under steady state conditions in LMFBR cores. This report describes the analytical models and numerical procedures employed in the code together with some typical results of the analysis made on large LMFBR cores. ARKAS is programmed in the FORTRAN-IV language and is capable of treating up to 260 assemblies in a cluster with flexible boundary conditions including mirror and rotational symmetry. The nonlinearity of the problem due to contact and separation is solved by the step iterative procedure based on the Newton-Raphson method. In each step iterative procedure, the linear matrix equation must be reconstructed and then solved directly. To save computer time and memory, the substructure method is adopted in the step of reconstructing the linear matrix equation, and in the step of solving the linear matrix equation, the block successive over-relaxation method is adopted. The program ARKAS computes, at every time step, 3-dimensional displacements and rotations of the subassemblies in the core and the interduct forces including at the nozzle tips and nozzle bases with friction effects. The code also has an ability to deal with the refueling and shuffling of subassemblies and to calculate the values of withdrawal forces. For the qualitative validation of the code, sample calculations were performed on the several bundle arrays. In these calculations, contact and separation processes under the influences of friction forces, off-center loading, duct rotations and torsion, thermal expansion and irradiation induced swelling and creep were analyzed. These results are quite reasonable in the light of the expected behaviour. This work was performed under the sponsorship of Toshiba Corporation

  14. Thermo-mechanical interaction effects in foam cored sandwich panels-correlation between High-order models and Finite element analysis results

    DEFF Research Database (Denmark)

    Palleti, Hara Naga Krishna Teja; Santiuste, Carlos; Thomsen, Ole Thybo

    2010-01-01

    Thermo-mechanical interaction effects including thermal material degradation in polymer foam cored sandwich structures is investigated using the commercial Finite Element Analysis (FEA) package ABAQUS/Standard. Sandwich panels with different boundary conditions in the form of simply supported...

  15. Nature of diffraction fringes originating in the core of core-shell nanoparticle Cu/SiO2 and formation mechanism of the structures

    Science.gov (United States)

    Radnaev, A. R.; Kalashnikov, S. V.; Nomoev, A. V.

    2016-05-01

    This article is devoted to the analysis of the reasons for the occurrence of diffraction fringes in the cores of the core-shell nanoparticles Cu/SiO2. Moiré and diffraction fringes are observed while studying the nanoparticle cores under a transmission electron microscope. The formation of diffraction fringes is closely connected to the mechanism of nanoparticle formation under study and appears to be its consequence, letting us develop a hypothesis of metastable phase formation in nanoparticle cores. In our opinion, the emergence of diffraction fringes in cores of copper is connected to clasterisation in solid solution oversaturated with silicon α-Cu with the diffused interphase state. Only copper and oxygen (oxygen is presented as oxides in such types of copper as M0 - up to 0.01%; and M1 - up to 0.03%), Copper and silicon with oxygen in a stoichiometric proportion that is only sufficient for silicon dioxide formation (SiO2), Copper and silicon with oxygen in an amount that is sufficient not only for silicon dioxide formation, but also for the dissolution of silicon in the α-Cu solid solution, The amount of silicon in the alloy is not sufficient for the total fixation of oxygen contained in copper, Copper, oxygen and silicon whose contamination is greater than 8 wt.%. In the first case, the top-cut of oxygen in α-Cu solid solution is 0.03% at the temperature of 1066 °C. At slow cooling, secondary recrystallisation leads to the formation of equilibrium Cu2O on the line of the ultimate solubility (Figure 1a - line of maximum solubility of oxygen in copper). In the case of fast cooling fixation of oversaturated, single-phase, non-equilibrium α-Cu, solid solution (heat-treated) takes place, which contains saluted oxygen in an interstice crystal lattice of copper.Room temperature for nonferrous alloys (metals) is sufficient for the diffusive mobility of atoms, but insufficient for the formation of an equilibrium phase and stable phase of Cu2O. This is why

  16. Designing and evaluating a persuasive child restraint television commercial.

    Science.gov (United States)

    Lewis, Ioni; Ho, Bonnie; Lennon, Alexia

    2016-01-01

    Relatively high rates of child restraint inappropriate use and misuse and faults in the installation of restraints have suggested a crucial need for public education messages to raise parental awareness of the need to use restraints correctly. This project involved the devising and pilot testing of message concepts, filming of a television advertisement (the TVC), and the evaluation of the TVC. This article focuses specifically upon the evaluation of the TVC. The development and evaluation of the TVC were guided by an extended theory of planned behavior that included the standard constructs of attitudes, subjective norms, and perceived behavioral control as well as the additional constructs of group norms and descriptive norms. The study also explored the extent to which parents with low and high intentions to self-check restraints differed on salient beliefs regarding the behavior. An online survey of parents (N = 384) was conducted where parents were randomly assigned to either the intervention group (n = 161), and therefore viewed the advertisement within the survey, or the control group (n = 223), and therefore did not view the advertisement. Following a one-off exposure to the TVC, the results indicated that, although not a significant difference, parents in the intervention group reported stronger intentions (M = 4.43, SD = 0.74) to self-check restraints than parents in the control group (M = 4.18, SD = 0.86). In addition, parents in the intervention group (M = 4.59, SD = 0.47) reported significantly higher levels of perceived behavioral control than parents in the control group (M = 4.40, SD = 0.73). The regression results revealed that, for parents in the intervention group, attitudes and group norms were significant predictors of parental intentions to self-check their child restraint. Finally, the exploratory analyses of parental beliefs suggested that those parents with low intentions to self-check child restraints were significantly more likely than

  17. Mechanical properties of Mo-Si-B alloys fabricated by using core-shell powder with dispersion of yttria nanoparticles

    Science.gov (United States)

    Byun, Jong Min; Bang, Su-Ryong; Choi, Won June; Kim, Min Sang; Noh, Goo Won; Kim, Young Do

    2017-01-01

    In recent years, refractory materials with excellent high-temperature properties have been in the spotlight as a next generation's high-temperature materials. Among these, Mo-Si-B alloys composed of two intermetallic compound phases (Mo5SiB2 and Mo3Si) and a ductile α-Mo phase have shown an outstanding thermal properties. However, due to the brittleness of the intermetallic compound phases, Mo-Si-B alloys were restricted to apply for the structural materials. So, to enhance the mechanical properties of Mo-Si-B alloys, many efforts to add rare-earth oxide particles in the Mo-Si-B alloy were performed to induce the improvement of strength and fracture toughness. In this study, to investigate the effect of adding nano-sized Y2O3 particles in Mo-Si-B alloy, a core-shell powder consisting of intermetallic compound phases as the core and nano-sized α-Mo and Y2O3 particles surrounding the core was fabricated. Then pressureless sintering was carried out at 1400 °C for 3 h, and the mechanical properties of sintered bodies with different amounts of Y2O3 particles were evaluated by Vickers hardness and 3-point bending test. Vickers hardness was improved by dispersed Y2O3 particles in the Mo-Si-B alloy. Especially, Mo-3Si-1B-1.5Y2O3 alloy had the highest value, 589 Hv. The fracture toughness was measured using Mo-3Si-1B-1.5Y2O3 alloy and the value indicated as 13.5 MPa·√m.

  18. Bidirectional Thermo-Mechanical Properties of Foam Core Materials Using DIC

    DEFF Research Database (Denmark)

    Taher, Siavash Talebi; Thomsen, Ole Thybo; M Dulieu-Barton, Janice

    2011-01-01

    mechanical properties at room and at elevated temperatures. The MAF enables the realization of pure compression or high compression to shear bidirectional loading conditions that is not possible with conventional Arcan fixtures. The MAF is attached to a standard universal test machine equiped...... with an environmental chamber using specially designed grips that allow the specimen to rotate, and hence reduces paristic effects due to misalignment. The objective is to measure the unidirectional and bidirectional mechanical properties of PVC foam materials at elevated tempreature using digital image correlation...

  19. Hydrothermal Synthesis and Mechanism of Unusual Zigzag Ag2Te and Ag2Te/C Core-Shell Nanostructures

    Directory of Open Access Journals (Sweden)

    Saima Manzoor

    2014-01-01

    Full Text Available A single step surfactant-assisted hydrothermal route has been developed for the synthesis of zigzag silver telluride nanowires with diameter of 50–60 nm and length of several tens of micrometers. Silver nitrate (AgNO3 and sodium tellurite (Na2TeO3, are the precursors and polyvinylpyrrolidone (PVP is used as surfactant in the presence of the reducing agent, that is, hydrazine hydrate (N2H4·H2O. In addition to the zigzag nanowires a facile hydrothermal reduction-carbonization route is proposed for the preparation of uniform core-shell Ag2Te/C nanowires. In case of Ag2Te/C synthesis process the same precursors are employed for Ag and Te along with the ethylene glycol used as reducing agent and glucose as the carbonizing agent. Morphological and compositional properties of the prepared products are analyzed with the help of scanning electron microscopy, transmission electron microscopy, and energy dispersive X-ray spectroscopy, respectively. The detailed formation mechanism of the zigzag morphology and reduction-carbonization growth mechanism for core-shell nanowires are illustrated on the bases of experimental results.

  20. On the age and formation mechanism of the core of the Quadrantid meteoroid stream

    Czech Academy of Sciences Publication Activity Database

    Abedin, A.; Spurný, Pavel; Wiegert, P.; Pokorný, P.; Borovička, Jiří; Brown, P.

    2015-01-01

    Roč. 261, November (2015), s. 100-117 ISSN 0019-1035 R&D Projects: GA ČR(CZ) GAP209/11/1382 Institutional support: RVO:67985815 Keywords : asteroids * comets * dynamics Subject RIV: BN - Astronomy, Celestial Mechanics, Astrophysics Impact factor: 3.383, year: 2015

  1. The thermal-mechanical behavior of fuel pins during power's maneuvering regime at stationary core loading on 2nd unit of KHNPP

    International Nuclear Information System (INIS)

    Ieremenko, M.; Ovdiyenko, Y.; Khalimonchuk, V.

    2007-01-01

    Results of thermal-mechanical behaviour of fuel pins during daily power's maneuvering regime that were proposed for second unit of Khmelnitsky NPP are presented. Calculations were performed for campaign's moments 100 and 160 fpd and for different type of regulation. Additionally calculations were performed for campaign 7. It is the design variant of the campaign and reactor core contains the high burnt fuel. Calculations of macro-core parameters (Kq, Kv) was performed by spatial computer code DYN3D. Calculations of micro-core parameters (fuel pin power) was performed by computer code DERAB. Calculations of thermal-mechanical behaviour of fuel pins was performed by computer code TRANSURANUS (Authors)

  2. Mechanical design philosophy for the graphite components of the core structure of an HTGR

    International Nuclear Information System (INIS)

    Bodmann, E.

    1987-01-01

    Parallel to the layout and design of the graphite components for THTRs and the succeeding high temperature reactor projects, the design methods for graphite components have been improved over the years. The aim of this works is to develop the design methods which take into account both the particular properties of graphite and the particular functions of the components. Because of the close relation ship between materials and design codes, this development work has progressed with the development, testing and qualification of German reactor graphite. In this paper, the experience in this field of Hochtemperatur Reaktorbau GmbH and the results of the work and approach to the design problems are reported. The example of a HTR 500 design for a 550 MWe power station is taken up, and the core structure is explained. The graphite components are divided into three classes according to the stress limits. The loading of these components is reviewed. The aim of the design is not the complete avoidance of failure, but to avoid the failure of a single component from leading to a disadvantageous consequence which is not allowable. The classification of loading events, Weibull statistics and maximum allowable stress, the formation of the permissible stress, the assessment of stress due to multiaxial loading and so on are described. (Kako, I.)

  3. An editor for the generation and customization of geometry restraints.

    Science.gov (United States)

    Moriarty, Nigel W; Draizen, Eli J; Adams, Paul D

    2017-02-01

    Chemical restraints for use in macromolecular structure refinement are produced by a variety of methods, including a number of programs that use chemical information to generate the required bond, angle, dihedral, chiral and planar restraints. These programs help to automate the process and therefore minimize the errors that could otherwise occur if it were performed manually. Furthermore, restraint-dictionary generation programs can incorporate chemical and other prior knowledge to provide reasonable choices of types and values. However, the use of restraints to define the geometry of a molecule is an approximation introduced with efficiency in mind. The representation of a bond as a parabolic function is a convenience and does not reflect the true variability in even the simplest of molecules. Another complicating factor is the interplay of the molecule with other parts of the macromolecular model. Finally, difficult situations arise from molecules with rare or unusual moieties that may not have their conformational space fully explored. These factors give rise to the need for an interactive editor for WYSIWYG interactions with the restraints and molecule. Restraints Editor, Especially Ligands (REEL) is a graphical user interface for simple and error-free editing along with additional features to provide greater control of the restraint dictionaries in macromolecular refinement.

  4. Heating mechanisms for intermittent loops in active region cores from AIA/SDO EUV observations

    Energy Technology Data Exchange (ETDEWEB)

    Cadavid, A. C.; Lawrence, J. K.; Christian, D. J. [Department of Physics and Astronomy, California State University Northridge, Northridge, CA 91330 (United States); Jess, D. B. [Astrophysics Research Centre, School of Mathematics and Physics, Queen' s University Belfast, Belfast BT7 1NN (United Kingdom); Nigro, G. [Universita della Calabria, Dipartimento di Fisica and Centro Nazionale Interuniversitario Struttura della Materia, Unita di Cosenza, I-87030 Arcavacata di Rende (Italy)

    2014-11-01

    We investigate intensity variations and energy deposition in five coronal loops in active region cores. These were selected for their strong variability in the AIA/SDO 94 Å intensity channel. We isolate the hot Fe XVIII and Fe XXI components of the 94 Å and 131 Å by modeling and subtracting the 'warm' contributions to the emission. HMI/SDO data allow us to focus on 'inter-moss' regions in the loops. The detailed evolution of the inter-moss intensity time series reveals loops that are impulsively heated in a mode compatible with a nanoflare storm, with a spike in the hot 131 Å signals leading and the other five EUV emission channels following in progressive cooling order. A sharp increase in electron temperature tends to follow closely after the hot 131 Å signal confirming the impulsive nature of the process. A cooler process of growing emission measure follows more slowly. The Fourier power spectra of the hot 131 Å signals, when averaged over the five loops, present three scaling regimes with break frequencies near 0.1 min{sup –1} and 0.7 min{sup –1}. The low frequency regime corresponds to 1/f noise; the intermediate indicates a persistent scaling process and the high frequencies show white noise. Very similar results are found for the energy dissipation in a 2D 'hybrid' shell model of loop magneto-turbulence, based on reduced magnetohydrodynamics, that is compatible with nanoflare statistics. We suggest that such turbulent dissipation is the energy source for our loops.

  5. Structure, Mechanics and Flow Properties of Fractured Shale: Core-Scale Experimentation and In-situ Imaging

    Science.gov (United States)

    Abdelmalek, B. F.; Karpyn, Z.; Liu, S.

    2014-12-01

    Over the last several years, hydrocarbon exploitation and development in North America has been heavily centered on shale gas plays. However, the physical attributes of shales and their manifestation on transport properties and storage capacity remain poorly understood. Therefore, more experimentally based data are needed to fill the gaps in understanding both transport and storage of fluids in shale. The proposed work includes installation and testing of an experimental system which is capable of monitoring the dynamic evolution of shale core permeability under variable loading conditions and in coordination with X-ray microCT imaging. The goal of this study is to better understand and quantify fluid flow patterns and associated transport dynamics of fractured shale samples. The independent variables considered in this study are: mechanical loading and pore pressure. The mechanical response of shale core is captured for different loading paths. To best replicate the in-situ production scenario, the pore pressure is progressively depleted to mimic pressure decline. During the course of experimentation, permeability is estimated using the pulse-decay method under tri-axial stress boundary conditions. Simultaneously, X-ray microCT imaging is used with a tracer gas that is allowed to flow through the sample as an illuminating agent. In the presence of an illuminating agent, either Xenon or Krypton, the X-ray CT scanner can image fractures, global pathways and diffusional fronts in the matrix, as well as sorption sites that reflect heterogeneities in the sample and localized deformation. Anticipated results from these experiments will help quantify permeability evolution as a function of different loading conditions and pore pressure depletion. Also, the X-ray images will help visualize the change of flow patterns and the intensity of sorption as a function of mechanical loading and pore pressure.

  6. Environmental restraints and life strategies: a habitat templet matrix.

    Science.gov (United States)

    Holm, E

    1988-02-01

    Four basic environmental restraints on life are deduced from the requirements of life's inherent order laws. Possible life strategies to contend with these restraints are listed. The various combinations of the restraints are subsequently investigated, and appropriate combinations of life strategies are fitted. This model is finally tested against insect case histories in various environments, and is demonstrated to explain some combinations of characteristics of insects in ecosystems not covered by the r-K or r-K-A continua. The role of heterochrony in achieving appropriate life strategies is briefly discussed.

  7. Do head-restraints protect the neck from whiplash injuries?

    Science.gov (United States)

    Morris, F

    1989-01-01

    Over an 11-month period a study was made of all patients presenting to an accident and emergency department who had sustained whiplash as a result of rear-bumper impacts. The patients were analysed with respect to the presence of head-restraints in their vehicles. A significant increase in the incidence of whiplash was found in patients whose vehicles did not have head-restraints fitted. Legislation requiring all passenger cars to have head-restraints fitted as standard would have a major impact in reducing the number of whiplash injuries sustained in rear bumper impacts. PMID:2712983

  8. Electroconvulsive Stimulation, but not Chronic Restraint Stress, Causes Structural Alterations in Adult Rat Hippocampus

    DEFF Research Database (Denmark)

    Olesen, Mikkel V.; Wörtwein, Gitta; Pakkenberg, Bente

    2015-01-01

    The neurobiological mechanisms underlying depression are not fully understood. Only a few previous studies have used validated stereological methods to test how stress and animal paradigms of depression affect adult hippocampal neurogenesis and whether antidepressant therapy can counteract possible...... changes in an animal model. Thus, in this study we applied methods that are state of the art in regard to stereological cell counting methods. Using a validated rat model of depression in combination with a clinically relevant schedule of electroconvulsive stimulation, we estimated the total number...... of newly formed neurons in the hippocampal subgranular zone. Also estimated were the total number of neurons and the volume of the granule cell layer in adult rats subjected to chronic restraint stress and electroconvulsive stimulation either alone or in combination. We found that chronic restraint stress...

  9. Comparison of the SASSYS/SAS4A radial core expansion reactivity feedback model and the empirical correlation for FFTF

    International Nuclear Information System (INIS)

    Wigeland, R.A.

    1987-01-01

    The present emphasis on inherent safety for LMR designs has resulted in a need to represent the various reactivity feedback mechanisms as accurately as possible. The dominant negative reactivity feedback has been found to result from radial expansion of the core for most postulated ATWS events. For this reason, a more detailed model for calculating the reactivity feedback from radial core expansion has been recently developed for use with the SASSYS/SAS4A Code System. The purpose of this summary is to present an extension to the model so that it is more suitable for handling a core restraint design as used in FFTF, and to compare the SASSYS/SAS4A results using this model to the empirical correlation presently being used to account for radial core expansion reactivity feedback to FFTF

  10. Thermophysical, hydrodynamic and mechanical aspects of molten core relocation to lower plenum

    Energy Technology Data Exchange (ETDEWEB)

    Suh, Kune Y.; Huh, Chang Wook [Seoul National University, Seoul (Korea, Republic of)

    1997-12-31

    This paper presents the current state of knowledge on molten material relocation into the lower plenum. Consequences of movement of material to the lower head are considered with regard to the potential for reactor pressure vessel failure from both thermal hydraulic and mechanical standpoints. The models are applied to evaluating various in-vessel retention strategies for the Korean Standard Power Plant (KSNPP) reactor. The results are summarized in terms of thermal response of the reactor vessel from the very relevant severe accident management perspective. 10 refs., 1 fig., 1 tab. (Author)

  11. Thermophysical, hydrodynamic and mechanical aspects of molten core relocation to lower plenum

    Energy Technology Data Exchange (ETDEWEB)

    Suh, Kune Y; Huh, Chang Wook [Seoul National University, Seoul (Korea, Republic of)

    1998-12-31

    This paper presents the current state of knowledge on molten material relocation into the lower plenum. Consequences of movement of material to the lower head are considered with regard to the potential for reactor pressure vessel failure from both thermal hydraulic and mechanical standpoints. The models are applied to evaluating various in-vessel retention strategies for the Korean Standard Power Plant (KSNPP) reactor. The results are summarized in terms of thermal response of the reactor vessel from the very relevant severe accident management perspective. 10 refs., 1 fig., 1 tab. (Author)

  12. Intergranular cracking mechanism in baffle former bolt materials for PWR core internals

    Energy Technology Data Exchange (ETDEWEB)

    Yonezawa, Toshio; Arioka, Koji; Kanasaki, Hiroshi; Fujimoto, Koji [Takasago R and D Center, Mitsubishi Heavy Industries Ltd., Takasago, Hyogo (Japan); Ajiki, Kazuhide [Kobe Shipyard and Machinery, Mitsubishi Heavy Industries Ltd., Kobe, Hyogo (Japan); Matsuoka, Takanori [Nuclear Development Corp., Tokai, Ibaraki (Japan); Urata, Sigeru; Mizuta, Hitoshi [Kansai Electric Power Co., Inc., Osaka (Japan)

    2000-03-01

    In this study, the cause of intergranular cracking in baffle former bolts(BFBs) was estimated from metallurgical and chemical viewpoints based upon the experimental data and information published by EdF. At first, five kinds of possibilities were estimated as the cause of intergranular cracking in BFBs. Five possibilities estimated were (1) mechanical cracking caused by high strain in irradiation hardened austenitic stainless steels, (2) O{sub 2} SCC due to residual oxygen in the bolt stagnant region, (3) caustic SCC due to dry and wet phenomenon, (4) low pH SCC due to oxygen concentration cell, and (5) PWSCC due to radiation induced segregation. In this study each possibility was evaluated by the calculation and some out of pile tests. And also, the cause of the intergranular cracking in BFBs was estimated by the data of the post-irradiation examinations and basic out of pile tests for Type 316CW and Type 347 stainless steels in the authors' previous study. From these evaluation, the intergranular cracking in BFBs seems to be caused by the PWSCC, but not caused by mechanical cracking O{sub 2} SCC, caustic SCC or low pH SCC. (author)

  13. One pot synthesis, growth mechanism and optical properties of Zn{sub 1-x}Cd{sub x}Se graded core/shell and alloy nanocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Sonawane, Kiran G. [Department of Physics, University of Pune, Pune 411 007 (India); Patil, K.R. [Centre for Materials Characterization, National Chemical Laboratory, Pune 411 008 (India); Mahamuni, Shailaja, E-mail: shailajamahamuni@yahoo.co.in [Department of Physics, University of Pune, Pune 411 007 (India)

    2013-03-15

    Comparatively higher photoluminescence yield along with robustness of core/shell semiconductor nanocrystals make them attractive candidates for studying intricate quantum size effects. Here, we report, one pot synthesis of Zn{sub 1-x}Cd{sub x}Se graded core/shell structures by exploiting change in the reactivity of precursors. Optical and structural measurements indicate formation of graded structure. Growth mechanism probed by inductively coupled plasma atomic emission spectroscopy shows formation of graded core/shell structure, with CdSe rich core and ZnSe rich shell. Annealing these nanocrystals, in chemical bath, leads to diffusion of Cd from core to shell region. Formation of Zn{sub 1-x}Cd{sub x}Se alloy is also observed in X-ray photoelectron spectroscopic measurements, confirming the diffusion of Cd from core to shell region. Substantially high photoluminescence quantum efficiency of 60% with narrow line width of about 27 nm, was observed and is attributable to the reduced strain due to graded core/shell structure. - Highlights: Black-Right-Pointing-Pointer Graded CdSe/ZnSe core-shell nanocrystals are synthesized exploiting reactivity of precursors. Black-Right-Pointing-Pointer Growth mechanism is probed using ICP-AES spectroscopy. Black-Right-Pointing-Pointer Reduced strain leads to luminescence efficiency as high as 60%. Black-Right-Pointing-Pointer Alloy formation by annealing in chemical bath is probed using XPS.

  14. A prospective study of children aged children and are associated with restraint misuse.

    Science.gov (United States)

    Skjerven-Martinsen, Marianne; Naess, Paal Aksel; Hansen, Trond Boye; Gaarder, Christine; Lereim, Inggard; Stray-Pedersen, Arne

    2014-12-01

    The implementation of the compulsory wearing of seat belts (SBs) for children and improvements in child restraint systems have reduced the number of deaths and severe injuries among children involved in motor vehicle (MV) collisions (MVCs). Establishing the characteristics predictive of such injuries may provide the basis for targeted safety campaigns and lead to a further reduction in mortality and morbidity among children involved in MVCs. This study performed a multidisciplinary investigation among child occupants involved in MVCs to elucidate injury mechanisms, evaluate the safety measures used and determine the characteristics that are predictive of injury. A prospective study was conducted of all child occupants aged interior of the MVs were investigated and the injured children were medically examined. Supplementary information was obtained from witnesses, the crash victims, police reports, medical records and reconstructions. Each case was reviewed by a multidisciplinary team to assess the mechanism of injury. In total, 158 child occupants involved in 100 MVCs were investigated, of which 27 (17%) exhibited Abbreviated Injury Scale (AIS) scores of 2+ injuries and 15 (9%) exhibited AIS 3+ injuries. None of the children died. Of those with AIS 2+ injuries (n=27), 89% (n=24) were involved in frontal impact collisions and 11% (3/27) were involved in side impacts. Multivariate analysis revealed that restraint misuse, age, the prevailing lighting conditions and ΔV were all independently correlated with AIS 2+ injuries. Safety errors were found in 74% (20/27) of those with AIS 2+ injuries and 93% (14/15) of those with AIS 3+ injuries. The most common safety error was misuse of restraints, and in particular loose and/or improperly positioned SBs. The risk of injury among child occupants is significantly higher when the child occupants are exposed to safety errors within the interior of the vehicle. Future campaigns should focus on the prevention of restraint misuse

  15. A versatile method for combining different biopolymers in a core/shell fashion by 3D plotting to achieve mechanically robust constructs.

    Science.gov (United States)

    Akkineni, Ashwini Rahul; Ahlfeld, Tilman; Lode, Anja; Gelinsky, Michael

    2016-10-07

    Three-dimensional extrusion of two different biomaterials in a core/shell (c/s) fashion has gained much interest in the last couple of years as it allows for fabricating constructs with novel and interesting properties. We now demonstrate that combining high concentrated (16.7 wt%) alginate hydrogels as shell material with low concentrated, soft biopolymer hydrogels as core leads to mechanically stable and robust 3D scaffolds. Alginate, chitosan, gellan gum, gelatin and collagen hydrogels were utilized successfully as core materials-hydrogels which are too soft for 3D plotting of open-porous structures without an additional mechanical support. The respective c/s scaffolds were characterized concerning their morphology, mechanical properties and swelling behavior. It could be shown that core as well as shell part can be loaded with growth factors and that the release depends on core composition and shell thickness. Neither the plotting process nor the crosslinking with 1M CaCl 2 denatured the proteins. When core and shell were loaded with different growth factors (VEGF and BMP-2, respectively) a dual release was achieved. Finally, live human endothelial cells were integrated in the core material, demonstrating that this new strategy can be used for bioprinting purposes as well.

  16. Experimental Study of Hydraulic Control Rod Drive Mechanism for Passive IN-core Cooling System of Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Kim, In Guk; Kim, Kyung Mo; Jeong, Yeong Shin; Bang, In Cheol [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    CAREM 25 (27 MWe safety systems using hydraulic control rod drives (CRD) studied critical issues that were rod drops with interrupted flow [3]. Hydraulic control rod drive suggested fast shutdown condition using a large gap between piston and cylinder in order to fast drop of neutron absorbing rods. A Passive IN-core Cooling system (PINCs) was suggested for safety enhancement of pressurized water reactors (PWR), small modular reactor (SMR), sodium fast reactor (SFR) in UNIST. PINCs consist of hydraulic control rod drive mechanism (Hydraulic CRDM) and hybrid control rod assembly with heat pipe combined with control rod. The schematic diagram of the hydraulic CRDM for PINCs is shown in Fig. 1. The experimental results show the steady state and transient behavior of the upper cylinder at a low pressure and low temperature. The influence of the working fluid temperature and cylinder mass are investigated. Finally, the heat removal between evaporator section and condenser section is compared with or without the hybrid control rod. Heat removal test of the hybrid heat pipe with hydraulic CRDM system showed the heat transfer coefficient of the bundle hybrid control rod and its effect on evaporator pool. The preliminary test both hydraulic CRDM and heat removal system was conducted, which showed the possibility of the in-core hydraulic drive system for application of PINCs.

  17. The Relationship between Restraints of Trade and Garden Leave

    Directory of Open Access Journals (Sweden)

    Yeukai Mupangavanhu

    2017-06-01

    Full Text Available The purpose of the article is to examine the relationship between a so-called "garden leave" clause and a post-termination restraint of trade clause in employment contracts, in view of the decision in Vodacom (Pty Ltd v Motsa 2016 3 SA 116 (LC. The Labour Court grappled with the question of whether the enforcement of the garden leave provision impacts on the enforcement of a post-termination restraint of trade clause. Enforcement of both these types of clauses may be problematic. It can result in unfairness if an employee ends up being commercially inactive for a long period. The author argues that garden leave has a direct effect on the enforcement of a post- termination restraint of trade clause. Accordingly, a restraint of trade will be enforced only if the employer's proprietary interest requires additional protection beyond what is achieved under the garden leave clause.

  18. Do emotion regulation difficulties when upset influence the association between dietary restraint and weight gain among college students?

    Science.gov (United States)

    Hunt, Tyler K; Forbush, Kelsie T; Hagan, Kelsey E; Chapa, Danielle A N

    2017-07-01

    Obesity is a significant public health concern that affects more than one-fifth of adolescents aged 12-19 in the United States. Theoretical models suggest that prolonged dietary restraint leads to binge-eating behaviors, which in turn increases individuals' risk for weight gain or obesity. Results from the literature indicate a potential role for negative urgency (the tendency to act rashly when distressed) as a mediating variable that explains the link between dietary restraint and binge-eating episodes. The current study tested short-term, prospective longitudinal associations among dietary restraint, binge eating, negative urgency, and weight gain among college students - a population at increased risk for the development of overweight and obesity. We hypothesized that dietary restraint and weight gain would be mediated by negative urgency and binge eating, but only among participants with overweight and obesity. College students (N = 227) completed the Eating Pathology Symptoms Inventory, UPPS-P Impulsivity Scale, and self-reported weight and height to calculate body mass index. Results showed that the association between dietary restraint and weight gain was mediated by negative urgency and binge eating, but only among participants with overweight and obesity. Our findings indicated that negative urgency might represent a mechanism that explains why dietary restraint leads to future binge-eating episodes and weight gain among college students with overweight and obesity. Results suggest that future treatment and prevention programs for overweight and obesity may benefit from incorporating strategies to improve emotion regulation as a way to reduce binge eating and to prevent additional weight gain among 'at-risk' populations. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Restraint use law enforcement intervention in Latino communities.

    Science.gov (United States)

    Schaechter, Judy; Uhlhorn, Susan B

    2011-11-01

    Motor vehicle crashes are the leading cause of death for U.S. Latinos aged 1 to 35 years. Restraint use is an effective means of prevention of motor vehicle crash injury. Effective interventions to raise restraint use include the following: legislation, law enforcement, education, and equipment distribution. The effects of law enforcement interventions in Latino immigrant communities are understudied. We measured the community-level effect of a combined intervention that included warnings and citations phase enforcement in Latino communities. We designed and implemented in two of three Latino-majority communities a multicomponent intervention consisting of a community awareness campaign, restraint use education with equipment distribution, and a two-staged law enforcement intervention. Restraint use observations were conducted in all three communities at baseline, after the warnings phase and again after the citations phase of the intervention were completed. The combined intervention of community awareness, education, child passenger restraint distribution, and law enforcement focused on educational traffic stops with incentives and warnings was associated with a significant increase in both driver and child passenger restraint use in one intervention community, but only driver restraint increased to a level of significance in the other intervention community; significant increase was also noted among nonintervention drivers. The citations phase of the intervention did not result in a significant increase in restraint use and was complicated by interruptions due to unlicensed drivers. The combined effort of community awareness, education, equipment distribution and law enforcement intervention that included incentives and warnings may be effective at increasing seat belt use in Latino communities without the need for citations.

  20. Ergonomic Evaluation of the Foot Restraint Equipment Device (FRED)

    Science.gov (United States)

    Whitmore, Mihriban; Chmielewski, Cindy; Qazi, A. S.; Mount, Francis

    1999-01-01

    Within the scope of the Microgravity Workstation and Restraint Evaluation project, funded by the NASA Headquarters Life Sciences Division, evaluations were proposed to be conducted in ground, KC-135, and/or Shuttle environments to investigate the human factors engineering (HFE) issues concerning confined/unique workstations, including crew restraint requirements. As part of these evaluations, KC-135 flights were conducted to investigate user/ workstation/ restraint integration for microgravity use of the FRED with the RMS workstation. This evaluation was a pre-cursor to Detailed Supplementary Objective (DSO) - 904 on STS-88. On that mission, a small-statured astronaut will be using the FRED restraint while working at the Aft RMS workstation. The DSO will collect video for later posture analyses, as well as subjective data in the form of an electronic questionnaire. This report describes the current FRED KC-135 evaluations. The primary objectives were to evaluate the usability of the FRED and to verify the DSO in-flight setup. The restraint interface evaluation consisted of four basic areas of restraint use: 1) adjustability; 2) general usability and comfort; 3) usability at the RMS workstation; and 4) assembly and disassembly.

  1. Restraint stress enhances arterial thrombosis in vivo--role of the sympathetic nervous system.

    Science.gov (United States)

    Stämpfli, Simon F; Camici, Giovanni G; Keller, Stephan; Rozenberg, Izabela; Arras, Margarete; Schuler, Beat; Gassmann, Max; Garcia, Irene; Lüscher, Thomas F; Tanner, Felix C

    2014-01-01

    Stress is known to correlate with the incidence of acute myocardial infarction. However, the molecular mechanisms underlying this correlation are not known. This study was designed to assess the effect of experimental stress on arterial thrombus formation, the key event in acute myocardial infarction. Mice exposed to 20 h of restraint stress displayed an increased arterial prothrombotic potential as assessed by photochemical injury-induced time to thrombotic occlusion. This increase was prevented by chemical sympathectomy performed through 6-hydroxydopamine (6-OHDA). Blood-born tissue factor (TF) activity was enhanced by stress and this increase could be prevented by 6-OHDA treatment. Vessel wall TF, platelet count, platelet aggregation, coagulation times (PT, aPTT), fibrinolytic system (t-PA and PAI-1) and tail bleeding time remained unaltered. Telemetric analysis revealed only minor hemodynamic changes throughout the stress protocol. Plasma catecholamines remained unaffected after restraint stress. Tumor necrosis factor alpha (TNF-α) plasma levels were unchanged and inhibition of TNF-α had no effect on stress-enhanced thrombosis. These results indicate that restraint stress enhances arterial thrombosis via the sympathetic nervous system. Blood-borne TF contributes, at least in part, to the observed effect whereas vessel wall TF, platelets, circulating coagulation factors, fibrinolysis and inflammation do not appear to play a role. These findings shed new light on the understanding of stress-induced cardiovascular events.

  2. Social isolation alters central nervous system monoamine content in prairie voles following acute restraint.

    Science.gov (United States)

    McNeal, Neal; Anderson, Eden M; Moenk, Deirdre; Trahanas, Diane; Matuszewich, Leslie; Grippo, Angela J

    2018-04-01

    Animal models have shown that social isolation and other forms of social stress lead to depressive- and anxiety-relevant behaviors, as well as neuroendocrine and physiological dysfunction. The goal of this study was to investigate the effects of prior social isolation on neurotransmitter content following acute restraint in prairie voles. Animals were either paired with a same-sex sibling or isolated for 4 weeks. Plasma adrenal hormones and ex vivo tissue concentrations of monoamine neurotransmitters and their metabolites were measured following an acute restraint stressor in all animals. Isolated prairie voles displayed significantly increased circulating adrenocorticotropic hormone levels, as well as elevated serotonin and dopamine levels in the hypothalamus, and potentially decreased levels of serotonin in the frontal cortex. However, no group differences in monoamine levels were observed in the hippocampus or raphe. The results suggest that social stress may bias monoamine neurotransmission and stress hormone function to subsequent acute stressors, such as restraint. These findings improve our understanding of the neurobiological mechanisms underlying the consequences of social stress.

  3. PIE technology on mechanical tests for HTTR core component and structural materials developed at Research Hot Laboratory

    International Nuclear Information System (INIS)

    Kizaki, Minoru; Honda, Junichi; Usami, Kouji; Ouchi, Asao; Oeda, Etsuro; Matsumoto, Seiichiro

    2001-02-01

    The high temperature engineering test reactor (HTTR) with the target operation temperature of 950degC established the first criticality on November, 1998 based on a large amount of R and D results on fuel and materials. In such R and D works, the development of reactor materials are one of the key issues from the view point of reactor environments such as extremely high temperature, neutron irradiation and so on for the HTTR. The Research Hot Laboratory (RHL) had carried out much kind of post irradiation examinations (PIEs) on core component and pressure vessel materials for during more than a quarter century. And obtained data played an important role in development, characterization and licensing of those materials for the HTTR. This paper describes the PIE technology developed at RHL and typical results on mechanical tests such as elevated temperature tensile and creep rupture tests for Hasteloy-X, Incolloy 800H and so on, and Charpy impact, J IC fracture toughness, K Id fracture toughness and small punch tests for normalized and tempered 2 1/4Cr-1Mo steel from historical view. In addition, an electrochemical test technique established for investigating the irradiation embrittlement mechanism on 2 1/4Cr-1Mo steel is also mentioned. (author)

  4. Mechanical energy yields and pressure volume and pressure time curves for whole core fuel-coolant interactions

    Energy Technology Data Exchange (ETDEWEB)

    Coddington, P [United Kingdom Atomic Energy Authority, Atomic Energy Establishment, Winfrith, Dorchester, Dorset (United Kingdom)

    1979-10-15

    In determining the damage consequences of a whole core Fuel-Coolant Interaction (FCI), one measure of the strength of a FCI that can be used and is independent of the system geometry is the constant volume mixing mechanical yield (often referred to as the Hicks-Menzies yield), which represents a near upper limit to the mechanical work of a FCI. This paper presents a recalculation of the Hicks-Menzies yields for UO{sub 2} and sodium for a range of initial fuel temperatures and fuel to coolant mass ratios, using recently published UO{sub 2} and sodium equation of state data. The work presented here takes a small number of postulated FCIs with as wide range as possible of thermal interaction parameters and determines their pressure-volume P(V) and pressure-time P(t) relations, using geometrical constraints representative of the reactor. Then by examining these P(V) and P(t) curves a representative pressure-relative volume curve or range of possible curves, for use in containment analysis, is recommended

  5. Anticipatory precrash restraint sensor feasibility study: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kercel, S.W.; Dress, W.B.

    1995-08-01

    This report explores feasibility of an anticipatory precrash restraint sensor. The foundation principle is the anticipation mechanism found at a primitive level of biological intelligence and originally formalized by the mathematical biologist Robert Rosen. A system based on formal anticipatory principles should significantly outperform conventional technologies. It offers the prospect of high payoff in prevention of death and injury. Sensors and processes are available to provide a good, fast, and inexpensive description of the present dynamical state of the vehicle to the embedded system model in the anticipation engine. The experimental part of this study found that inexpensive radar in a real-world setting does return useful data on target dynamics. The data produced by a radar system can be converted to target dynamical information by good, fast and inexpensive signal-processing techniques. Not only is the anticipatory sensor feasible, but further development under the sponsorship of the National Highway Traffic Safety Administration is necessary and desirable. There are a number of possible lines of follow-on investigation. The level of effort and expected benefits of various alternatives are discussed.

  6. [New theory of holistic integrative physiology and medicine. III: New insight of neurohumoral mechanism and pattern of control and regulation for core axe of respiration, circulation and metabolism].

    Science.gov (United States)

    Sun, Xing-guo

    2015-07-01

    Systemic mechanism of neurohumoral control and regulation for human is limited. We used the new theory of holistic integrative physiology and medicine to approach the mechanism and pattern of neurohumoral control and regulation for life. As the core of human life, there are two core axes of functions. The first one is the common goal of respiration and circulation to transport oxygen and carbon dioxide for cells, and the second one is the goal of gastrointestinal tract and circulation to transport energy material and metabolic product for cells. These two core axes maintain the metabolism. The neurohumoral regulation is holistically integrated and unified for all functions in human body. We simplified explain the mechanism of neurohumoral control and regulation life (respiration and circulation) as the example pattern of sound system. Based upon integrated regulation of life, we described the neurohumoral pattern to control respiration and circulation.

  7. Reactor core

    International Nuclear Information System (INIS)

    Azekura, Kazuo; Kurihara, Kunitoshi.

    1992-01-01

    In a BWR type reactor, a great number of pipes (spectral shift pipes) are disposed in the reactor core. Moderators having a small moderating cross section (heavy water) are circulated in the spectral shift pipes to suppress the excess reactivity while increasing the conversion ratio at an initial stage of the operation cycle. After the intermediate stage of the operation cycle in which the reactor core reactivity is lowered, reactivity is increased by circulating moderators having a great moderating cross section (light water) to extend the taken up burnup degree. Further, neutron absorbers such as boron are mixed to the moderator in the spectral shift pipe to control the concentration thereof. With such a constitution, control rods and driving mechanisms are no more necessary, to simplify the structure of the reactor core. This can increase the fuel conversion ratio and control great excess reactivity. Accordingly, a nuclear reactor core of high conversion and high burnup degree can be attained. (I.N.)

  8. A COMPARATIVE STUDY TO FIND OUT THE EFFECTIVENESS BETWEEN CORE STABILIZATION VS MCKENZIE EXERCISES IN THE TREATMENT OF PATIENTS WITH MECHANICAL LOW BACK PAIN

    Directory of Open Access Journals (Sweden)

    Abhijit Dutta

    2015-10-01

    Full Text Available Background: Mechanical Low back pain is a leading cause of disability. It occurs in similar proportions in all cultures, interferes with quality of life and work performance. Both male and female populations are affected; however, there is a tendency towards a higher incidence in male patients. Mechanical low back pain is associated with pain and clinical instability in lumbar motion segments. Exercises play an important part in the rehabilitation of low back pain. The aim of this study was to compare the effectiveness between Core stabilization vs McKenzie exercises in the treatment of patients with mechanical low back pain. Methods: 30 patients were selected between the age groups of 20 yrs to 50 yrs and having a past history of low back pain for one month. 15 patients were allotted to each group of experiment. Group I was given Core stabilization exercises and Group II with McKenzie exercises. Interferential therapy was a common treatment for both the groups. Evaluations of the subjects were done using the Revised Oswestry Disability Index and Dynamic Endurance tests. Results: Data analysis revealed statistically significant difference between both the groups (p<0.05 and proved that Core stabilization exercises is more effective than McKenzie exercises in mechanical low back pain. Conclusion: This study shows that core stabilization exercises possess a greater potential over McKenzie exercises in treating Mechanical Low back pain patients.

  9. F.B.R. Core mock-up RAPSODIE- I: Experimental analysis

    International Nuclear Information System (INIS)

    Brochard, D.; Buland, P.; Gantenbein, F.

    1990-01-01

    The main phenomena which influence the LMFBR core response to a seismic excitation are the fluid structure interaction and the impacts between subassemblies. To study the core behaviour, seismic tests have been performed on the core mock-up RAPSODIE with or without fluid and restraint ring and for different levels of excitation. This paper summarizes the results of these tests

  10. Inhibition of misleading heuristics as a core mechanism for typical cognitive development: evidence from behavioural and brain-imaging studies.

    Science.gov (United States)

    Borst, Grégoire; Aïte, Ania; Houdé, Olivier

    2015-04-01

    Cognitive development is generally conceived as incremental with knowledge of increasing complexity acquired throughout childhood and adolescence. However, several studies have now demonstrated not only that infants possess complex cognitive abilities but also that older children, adolescents, and adults tend to make systematic errors even in simple logical reasoning tasks. Therefore, one of the main issues for any theory of typical cognitive development is to provide an explanation of why at some age and in some contexts children, adolescents, and adults do not express a knowledge or cognitive principle that they already acquired when they were younger. In this review, we present convergent behavioural and neurocognitive evidence that cognitive development is more similar to a non-linear dynamic system than to a linear, stage-like system. In this theoretical framework, errors can emerge in problems similar to the ones infants or young children were succeeding when older children, adolescents, and adults rely on a misleading heuristic rather than on the correct logical algorithm to solve such problems. And the core mechanism for overcoming these errors is inhibitory control (i.e. the ability to inhibit the misleading heuristics). Therefore, typical cognitive development relies not only on the ability to acquire knowledge of incremental complexity but also to inhibit previously acquired knowledge. © 2015 The Authors. Developmental Medicine & Child Neurology © 2015 Mac Keith Press.

  11. PBDOWN - a computer code for simulating core material discharge and thermal to mechanical energy conversion in LMFBR hypothetical accidents

    International Nuclear Information System (INIS)

    Royl, P.

    1981-01-01

    PBDOWN is a computer code that simulates the blowdown of confined boiling materials ('pools') into a colder upper coolant plenum as time dependent ejection and expansion with consideration of a few selected exchange processes. Its application is restricted to situations resulting from hypothetical loss of flow (LOF) accidents in LMFBR's, where enough voiding has occured, that in core sodium vapor pressures become negligible. PBDOWN considers one working fluid for the discharge process (either fuel or steel) and a maximum of two working fluids (either fuel and sodium or steel and sodium) for the expansion process in the upper coolant plenum. Entrainment of sodium at the accelerated bubble liquid interfaces is mechanistically calculated by a Taylor instability entrainment model. Simulation of a hemispherical expansion form together with this mechanistic entrainment model gives a new integrated calculation of the time dependent sodium mass in the bubble. The paper summarizes the basic equations and assumptions of this computer model. Sample results compare different heat transfer and Na entrainment models during steel and fuel driven discharge processes. Mechanistic sodium entrainment simulation for SNR-type reactors coupled with a realistic heat transfer model is shown to reduce the integral mechanical work potential by a factor of 1.3 to 2.0 over the isentropic energy of the discharge working fluids. (orig.)

  12. Biomechanical evaluation of bending strength of spinal pedicle screws, including cylindrical, conical, dual core and double dual core designs using numerical simulations and mechanical tests.

    Science.gov (United States)

    Amaritsakul, Yongyut; Chao, Ching-Kong; Lin, Jinn

    2014-09-01

    Pedicle screws are used for treating several types of spinal injuries. Although several commercial versions are presently available, they are mostly either fully cylindrical or fully conical. In this study, the bending strengths of seven types of commercial pedicle screws and a newly designed double dual core screw were evaluated by finite element analyses and biomechanical tests. All the screws had an outer diameter of 7 mm, and the biomechanical test consisted of a cantilever bending test in which a vertical point load was applied using a level arm of 45 mm. The boundary and loading conditions of the biomechanical tests were applied to the model used for the finite element analyses. The results showed that only the conical screws with fixed outer diameter and the new double dual core screw could withstand 1,000,000 cycles of a 50-500 N cyclic load. The new screw, however, exhibited lower stiffness than the conical screw, indicating that it could afford patients more flexible movements. Moreover, the new screw produced a level of stability comparable to that of the conical screw, and it was also significantly stronger than the other screws. The finite element analysis further revealed that the point of maximum tensile stress in the screw model was comparable to the point at which fracture occurred during the fatigue test. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

  13. Comprehensive thermal-hydraulic and thermal-mechanical analysis of core and fuel rods for the safety validation of real refueling at the Kozloduy WWER-440

    Energy Technology Data Exchange (ETDEWEB)

    Stefanova, S; Panajotov, D; Ilieva, B; Vitkova, M; Simeonova, V; Passage, G; Manolova, M [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. za Yadrena Izsledvaniya i Yadrena Energetika

    1996-12-31

    Safety analysis aimed at determination of thermal-hydraulic and thermal-mechanical margins of core and fuel rods has been carried out using computer codes COBSOFM and PIN-micro. Thermal-hydraulic calculations for the part of the core with maximum heat flux during steady-state regime show that the coolant, cladding and fuel temperatures are within the design limits. A severe accident with reactor blackout has been simulated. It is found that at 95% probability level there is no boiling crisis anywhere in the core. The thermal-mechanical parameters of working assembly fuel rod with maximum load have been calculated. The assembly linear power reached a maximum of 25 kW/m during the second fuel cycle, the fuel temperature remaining well below 1000{sup o} C. As the fuel assembly with typical power history has enough safety margins, it was proposed to use it for one more cycle. 4 refs., 12 figs.

  14. On-Chip Scan-Based Test Strategy for a Dependable Many-Core Processor Using a NoC as a Test Access Mechanism

    NARCIS (Netherlands)

    Zhang, X.; Kerkhoff, Hans G.; Vermeulen, Bart

    2010-01-01

    Periodic on-chip scan-based tests have to be applied to a many-core processor SoC to improve its dependability. An infrastructural IP module has been designed and incorporated into the SoC to function as an ATE. This paper introduces the reuse of a Network-on-Chip as a test access mechanism. Since

  15. Effects of the vessel core seismic interaction for a fast reactor

    International Nuclear Information System (INIS)

    Martelli, A.; Maresca, G.

    1983-01-01

    This report describes the features and the results of the analysis carried out in collaboration between ENEA and NIRA for evaluating the effects of the vessel core dynamic interaction in case of safe shutdown earthquake, both in absence and in presence of one or two restraint plates inserted in the tank close to the middle and or top planes for limiting the core seismic motion. Such analysis, although carried out making use of preliminary data, contributed to the recent ENEA decision of applying a core restraint close to the core element top

  16. [Medical-legal issues of physical and pharmacological restraint].

    Science.gov (United States)

    Gómez-Durán, Esperanza L; Guija, Julio A; Ortega-Monasterio, Leopoldo

    2014-03-01

    The use of physical and pharmacological restraint is controversial but is currently accepted as inevitable. It is indicated for controlling behavioral disorders and psychomotor agitation that put patients and third parties at risk. Its indication should be medical, and we should opt for the least restrictive measure. Restraints represent a possible infringement of patients' fundamental rights and require understanding and strict respect for the medical-legal precepts by physicians and other practitioners involved in its application. This article reviews the current legal framework, as well as the medical-legal premises and aspects of applying restraints, with the objective of ensuring maximum respect for patients' rights and the appropriate legal safety in the activity of practitioners. Copyright © 2014 Elsevier España, S.L. All rights reserved.

  17. Mars Science Laboratory Differential Restraint: The Devil is in the Details

    Science.gov (United States)

    Jordan, Elizabeth

    2012-01-01

    The Differential Restraint, a mechanism used on the Mars Science Laboratory (MSL) rover to maintain symmetry of the mobility system during the launch, cruise, and entry descent and landing phases of the MSL mission, completed nearly three full design cycles before a finalized successful design was achieved. This paper address the lessons learned through these design cycles, including three major design elements that can easily be overlooked during the design process, including, tolerance stack contribution to load path, the possibility of Martian dirt as a failure mode, and the effects of material properties at temperature extremes.

  18. The application of mechanical desktop in the design of the reactor core structure of China advanced research reactor

    International Nuclear Information System (INIS)

    Lang Ruifeng

    2002-01-01

    The three-dimensional parameterization design method is introduced to the design of reactor core structure for China advanced research reactor. Based on the modeling and dimension variable driving of the main parts as well as the modification of dimension variable, the preliminary design and modification of reactor core is carried out with high design efficiency and quality as well as short periods

  19. Mechanical ball-milling preparation of fullerene/cobalt core/shell nanocomposites with high electrochemical hydrogen storage ability.

    Science.gov (United States)

    Bao, Di; Gao, Peng; Shen, Xiande; Chang, Cheng; Wang, Longqiang; Wang, Ying; Chen, Yujin; Zhou, Xiaoming; Sun, Shuchao; Li, Guobao; Yang, Piaoping

    2014-02-26

    The design and synthesis of new hydrogen storage nanomaterials with high capacity at low cost is extremely desirable but remains challenging for today's development of hydrogen economy. Because of the special honeycomb structures and excellent physical and chemical characters, fullerenes have been extensively considered as ideal materials for hydrogen storage materials. To take the most advantage of its distinctive symmetrical carbon cage structure, we have uniformly coated C60's surface with metal cobalt in nanoscale to form a core/shell structure through a simple ball-milling process in this work. The X-ray diffraction (XRD), scanning electron microscope (SEM), Raman spectra, high-solution transmission electron microscopy (HRTEM), energy-dispersive X-ray spectrometry (EDX) elemental mappings, and X-ray photoelectron spectroscopy (XPS) measurements have been conducted to evaluate the size and the composition of the composites. In addition, the blue shift of C60 pentagonal pinch mode demonstrates the formation of Co-C chemical bond, and which enhances the stability of the as-obtained nanocomposites. And their electrochemical experimental results demonstrate that the as-obtained C60/Co composites have excellent electrochemical hydrogen storage cycle reversibility and considerably high hydrogen storage capacities of 907 mAh/g (3.32 wt % hydrogen) under room temperature and ambient pressure, which is very close to the theoretical hydrogen storage capacities of individual metal Co (3.33 wt % hydrogen). Furthermore, their hydrogen storage processes and the mechanism have also been investigated, in which the quasi-reversible C60/Co↔C60/Co-Hx reaction is the dominant cycle process.

  20. Mechanisms of Breast Cancer in Shift Workers: DNA Methylation in Five Core Circadian Genes in Nurses Working Night Shifts.

    Science.gov (United States)

    Samulin Erdem, Johanna; Skare, Øivind; Petersen-Øverleir, Marte; Notø, Heidi Ødegaard; Lie, Jenny-Anne S; Reszka, Edyta; Pepłońska, Beata; Zienolddiny, Shanbeh

    2017-01-01

    Shift work has been suggested to be associated with breast cancer risk, and circadian disruption in shift workers is hypothesized as one of the mechanisms of increased cancer risk. There is, however, insufficient molecular evidence supporting this hypothesis. Using the quantitative methodology of pyrosequencing, epigenetic changes in 5-methyl cytosine (5mC) in five circadian genes CLOCK , BMAL1 , CRY1, PER1 and PER2 in female nurses working night shift work (278 breast cancer cases, 280 controls) were analyzed. In breast cancer cases, a medium exposure to night work was associated with increased methylation levels of the CLOCK (p=0.050), BMAL1 (p=0.001) and CRY1 (p=0.040) genes, compared with controls. Within the cases, analysis of the effects of shift work on the methylation patterns showed that methylation of CRY1 was lower in those who had worked night shift and had a high exposure (p=0.006) compared with cases that had worked only days. For cases with a medium exposure to night work, an increase in BMAL1 (p=0.003) and PER1 (p=0.035) methylation was observed compared with day working (unexposed) cases. The methylation levels of the five core circadian genes were also analyzed in relation to the estrogen and progesterone receptors status of the tumors in the cases, and no correlations were observed. Furthermore, nineteen polymorphisms in the five circadian genes were assessed for their effects on the methylation levels of the respective genes, but no associations were found. In summary, our data suggest that epigenetic regulation of CLOCK , BMAL1, CRY1 and PER1 may contribute to breast cancer in shift workers.

  1. Effect of silica fiber on the mechanical and chemical behavior of alumina-based ceramic core material

    OpenAIRE

    Weiguo Jiang; Kaiwen Li; Jiuhan Xiao; Langhong Lou

    2017-01-01

    In order to improve the chemical leachability, the alumina-based ceramic core material with the silica fiber was injected and sintered at 1100 °C/4 h, 1200 °C/4 h, 1300 °C/4 h and 1400 °C/4 h, respectively. The micrographs of ceramic core materials at sintered and leached state were characterized by scanning electron microscopy (SEM). The phase composition of ceramic core material after sintering and the leaching product after leaching were detected by X-ray diffraction (XRD). The porosity, r...

  2. A bimodal neurophysiological study of motor control in attention-deficit hyperactivity disorder: a step towards core mechanisms?

    Science.gov (United States)

    Heinrich, Hartmut; Hoegl, Thomas; Moll, Gunther H; Kratz, Oliver

    2014-04-01

    Knowledge about the core neural mechanisms of attention-deficit hyperactivity disorder, a pathophysiologically heterogeneous psychiatric disorder starting in childhood, is still limited. Progress may be achieved by combining different methods and levels of investigation. In the present study, we investigated neural mechanisms of motor control in 19 children with attention-deficit hyperactivity disorder (aged 9-14 years) and 21 age-matched typically developing children by relating neural markers of attention and response control (using event-related potentials) and measures of motor excitability/inhibition (evoked by transcranial magnetic stimulation). Thus, an interplay of processes at a subsecond scale could be studied. Using a monetary incentives-based cued Go/No-Go task, parameters that are well-known to be reduced in attention-deficit hyperactivity disorder were analysed: event-related potential components P3 (following cue stimuli; in Go and No-Go trials) and contingent negative variation as well as the transcranial magnetic stimulation-based short-interval intracortical inhibition measured at different latencies in Go and No-Go trials. For patient and control groups, different associations were obtained between performance, event-related potential and transcranial magnetic stimulation measures. In children with attention-deficit hyperactivity disorder, the P3 amplitude in Go trials was not correlated with reaction time measures but with short-interval intracortical inhibition at rest (r=0.56, P=0.01). In No-Go trials, P3 and short-interval intracortical inhibition after inhibiting the response (at 500 ms post-stimulus) were correlated in these children only (r=0.62; P=0.008). A classification rate of 90% was achieved when using short-interval intracortical inhibition (measured shortly before the occurrence of a Go or No-Go stimulus) and the amplitude of the P3 in cue trials as input features in a linear discriminant analysis. Findings indicate deviant neural

  3. 32 CFR 884.3 - Placing member under restraint pending delivery.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false Placing member under restraint pending delivery. 884.3 Section 884.3 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE... member under restraint pending delivery. Continue restraint only as long as is reasonably necessary to...

  4. Mechanical Property Comparison of the Soviet BS-41 and the US M993 Armor-Penetrating Cores

    Science.gov (United States)

    2016-11-23

    influences the formation of cracks at the tips of hardness indentations. The observations from the optical and SEM micrographs allow one to better...core is a fine-grained WC cemented in cobalt. The M993 core was determined to have superior hardness and indentation toughness. The superior... hardness , toughness, microstructure, composition 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18. NUMBER OF PAGES 20 19a

  5. Seismic anisotropy; a window on how the Earth works: multiple mechanisms and sites, from shallow mantle to inner core

    Science.gov (United States)

    Osmaston, Miles

    2013-04-01

    Since the seismic anisotropy (SA) in the uppermost oceanic mantle was discovered [1] and attributed to the shearing of olivine by an MOR-divergent flow velocity gradient, rheological mobility interpretations of this type have dominated studies of SA there and elsewhere in the Earth. Here I describe two other SA-generating mechanisms. I will reason that one of these, the anisotropic crystallization from melt, bids fair largely to replace the shearing one and be present in even larger volumes of the Earth, both within its outer 100km and in the Inner Core. The other, the layered deposition of disparate substances, offers to explain the ULVZs and SA in D''. We start with the Upper Mantle. New constraints on its rheological properties and dynamical behaviour have come from two directions. Firstly, contrary to the seismologists' rule-book, the oceanic LVZ is no longer to be thought of as mobile because the presence of interstitial melt strips out the water-weakening of the mineral structure [2, 3]. So we require a substitute for the divergent-flow model for MORs. In fact it also has three other, apparently unrecognized, dynamical inconsistencies. One of these [4] is that there are in the record many rapid changes of spreading rate and direction, and ridge jumps. This cannot happen with a process driven by slow-to-change body forces. Secondly, during the past decade, my work on the global dynamics for the past 150Ma (I will show examples) has shown [4 - 7] that the tectospheres of cratons must extend to very close to the bottom of the upper mantle. And that East Antarctica's 'keel' must actually reach it, because its CW rotation [7] suggests it has been picking up an electromagnetic torque from the CMB via the lower mantle. Xenoliths suggest that the reason for this downwards extent of 'keels' is the same as [3]. To meet these two sets of constraints I will demonstrate my now not-so-new MOR model, which has a narrow, wall-accreting subaxial crack. Among its many features

  6. Food Intake and Success or Failure of Dietary Restraint

    NARCIS (Netherlands)

    Anschutz, D.J.; Strien, T. van; Engels, R.C.M.E.

    2006-01-01

    Objectives: Determination of success and failure of dietary restraint in relation to food intake in 510 females. Methods: Food intake as measured with the Food Frequency Questionnaire (FFQ) was assessed in low vs. high restrained eaters and overeaters, as measured with the DEBQ (Dutch Eating

  7. 49 CFR 213.110 - Gage restraint measurement systems.

    Science.gov (United States)

    2010-10-01

    ... requirements specified in §§ 213.109 and 213.127. (5) If the PTLF becomes non-functional or is missing, the... and fastener requirements specified in §§ 213.109 and 213.127 provided that— (1) The track owner... the minimum design requirements of a GRMS vehicle which specify that— (1) Gage restraint shall be...

  8. Restraint stress impairs glucose homeostasis through altered insulin ...

    African Journals Online (AJOL)

    The study investigated the potential alteration in the level of insulin and adiponectin, as well as the expression of insulin receptors (INSR) and glucose transporter 4 GLUT-4 in chronic restraint stress rats. Sprague-Dawley rats were randomly divided into two groups: the control group and stress group in which the rats were ...

  9. Restraint stress and social defeat: What they have in common.

    Science.gov (United States)

    Motta, Simone Cristina; Canteras, Newton Sabino

    2015-07-01

    Bob Blanchard was a great inspiration for our studies on the neural basis of social defense. In the present study, we compared the hypothalamic pattern of activation between social defeat and restraint stress. As important stress situations, both defeated and immobilized animals displayed a substantial increase in Fos in the parvicellular part of the paraventricular nucleus,mostly in the region that contains the CRH neurons. In addition, socially defeated animals, but not restrained animals, recruited elements of the medial hypothalamic conspecific-responsive circuit, a region also engaged in other forms of social behavior. Of particular interest, both defeated and immobilized animals presented a robust increase in Fos expression in specific regions of the lateral hypothalamic area (i.e., juxtaparaventricular and juxtadorsomedial regions) likely to convey septo-hippocampal information encoding the environmental boundary restriction observed in both forms of stress, and in the dorsomedial part of the dorsal premammillary nucleus which seems to work as a key player for the expression of, at least, part of the behavioral responses during both restraint and social defeat. These results indicate interesting commonalities between social defeat and restraint stress, suggesting, for the first time, a septo-hippocampal–hypothalamic path likely to respond to the environmental boundary restriction that may act as common stressor component for both types of stress. Moreover, the comparison of the neural circuits mediating physical restraint and social defense revealed a possible path for encoding the entrapment component during social confrontation.

  10. Conceptual design of pipe whip restraints using interactive computer analysis

    International Nuclear Information System (INIS)

    Rigamonti, G.; Dainora, J.

    1975-01-01

    Protection against pipe break effects necessitates a complex interaction between failure mode analysis, piping layout, and structural design. Many iterations are required to finalize structural designs and equipment arrangements. The magnitude of the pipe break loads transmitted by the pipe whip restraints to structural embedments precludes the application of conservative design margins. A simplified analytical formulation of the nonlinear dynamic problems associated with pipe whip has been developed and applied using interactive computer analysis techniques. In the dynamic analysis, the restraint and the associated portion of the piping system, are modeled using the finite element lumped mass approach to properly reflect the dynamic characteristics of the piping/restraint system. The analysis is performed as a series of piecewise linear increments. Each of these linear increments is terminated by either formation of plastic conditions or closing/opening of gaps. The stiffness matrix is modified to reflect the changed stiffness characteristics of the system and re-started using the previous boundary conditions. The formation of yield hinges are related to the plastic moment of the section and unloading paths are automatically considered. The conceptual design of the piping/restraint system is performed using interactive computer analysis. The application of the simplified analytical approach with interactive computer analysis results in an order of magnitude reduction in engineering time and computer cost. (Auth.)

  11. The Cost of Prior Restraint: "U. S. v. The Progressive."

    Science.gov (United States)

    Soloski, John; Dyer, Carolyn Stewart

    Increased litigation and rising litigation costs threaten the future of newspapers and magazines. A case study was conducted to determine the costs and effects of "United States v. 'The Progressive,'" a prior restraint case over the publication in 1979 of an article on the hydrogen bomb. "The Progressive," which operates at a…

  12. Chronic restraint stress in rats causes sustained increase in urinary corticosterone excretion without affecting cerebral or systemic oxidatively generated DNA/RNA damage

    DEFF Research Database (Denmark)

    Jorgensen, Anders; Maigaard, Katrine; Wörtwein, Gitta

    2013-01-01

    acids, 8-oxo-7,8-dihydro-2'-deoxyguanosine (8-oxodG) and 8-oxo-7,8-dihydroguanosine (8-oxoGuo), respectively, in rats subjected to chronic restraint stress. To reliably collect 24h urine samples, the full 3-week restraint stress paradigm was performed in metabolism cages. We further determined frontal...... and Tnf). The metabolism cage housing in itself did not significantly influence a range of biological stress markers. In the restraint stress group, there was a sustained 2.5 fold increase in 24h corticosterone excretion from day 2 after stress initiation. However, neither whole-body nor cerebral measures......Increased oxidatively generated damage to nucleic acids (DNA/RNA) may be a common mechanism underlying accelerated aging in psychological stress states and mental disorders. In the present study, we measured the urinary excretion of corticosterone and markers of systemic oxidative stress on nucleic...

  13. Mechanical-Stratigraphic Characterization of the Eagle Ford Formation in Outcrop and Core, McMullen and Terrell Counties, Texas

    Science.gov (United States)

    Xu, G.; Chester, J. S.; Chester, F. M.

    2017-12-01

    The objective of this project is to characterize the geomechanical properties of individual and composite lithologic units over length scales of decimeter to tens of meters. We have characterized the stratigraphy and lithology of the Eagle Ford Formation in outcrops at Lozier and Antonio Canyons of West TX, and in core taken at 3.2 km depth in McMullen County, TX. Dominant lithologies examined include reworked ash layers, argillaceous mudstone, organic-rich mudstone, foraminifera wackestone, packstone, pyritic packstone, and foraminifera/dolomitic packstone-grainstone. Samples of these units are deformed in triaxial compression at 1- 40 MPa confining pressure (Pc), and room temperature and humidity. The elastic properties, pre-fracture yielding (ductility), and fracture strength are primarily a function of particle size, texture (degree of mud versus grain support), and composition. Young's Modulus (YM) and Poison's Ratio (PR) increase similarly with an increase in grain-support and carbonate content, and a decrease in organic matter and clay. The greatest change occurs at the transition from mud-supported to grain-supported textures where YM and PR increase by a factor of 3 and 1.5, respectively. Both YM and PR can display anisotropy with directional variation of 30%, most notably in micro-laminated units, but also in the more massive pyritic packstones. Overall, pre-fracture ductility decreases with an increase in carbonate content; ductile strain in the argillaceous- and organic-rich-mudstones is 1.4%, 3-4 times greater than that in the packstone/grainstone. Fracture strength increases with an increase in carbonate content and a decrease in clay content. The organic rich mudstone fails at 130 MPa, is nearly 2 times stronger than argillaceous mudstones, and 50% weaker than packstone/grainstones at 1 MPa Pc. The angle of internal friction is 45 degrees for all lithologies, consistent with a transition in fracture from opening- to shear-mode between 1 to 15 MPa Pc

  14. Effects of acupuncture on behavioral, cardiovascular and hormonal responses in restraint-stressed Wistar rats

    Directory of Open Access Journals (Sweden)

    Guimarães C.M.

    1997-01-01

    Full Text Available Stress is a well-known entity and may be defined as a threat to the homeostasis of a being. In the present study, we evaluated the effects of acupuncture on the physiological responses induced by restraint stress. Acupuncture is an ancient therapeutic technique which is used in the treatment and prevention of diseases. Its proposed mechanisms of action are based on the principle of homeostasis. Adult male Wistar EPM-1 rats were divided into four groups: group I (N = 12, unrestrained rats with cannulas previously implanted into their femoral arteries for blood pressure and heart rate measurements; group II (N = 12, rats that were also cannulated and were submitted to 60-min immobilization; group III (N = 12, same as group II but with acupuncture needles implanted at points SP6, S36, REN17, P6 and DU20 during the immobilization period; group IV (N = 14, same as group III but with needles implanted at points not related to acupuncture (non-acupoints. During the 60-min immobilization period animals were assessed for stress-related behaviors, heart rate, blood pressure and plasma corticosterone, noradrenaline and adrenaline levels. Group III animals showed a significant reduction (60% on average, P<0.02 in restraint-induced behaviors when compared to groups II and IV. Data from cardiovascular and hormonal assessments indicated no differences between group III and group II and IV animals, but tended to be lower (50% reduction on average in group I animals. We hypothesize that acupuncture at points SP6, S36, REN17, P6 and DU20 has an anxiolytic effect on restraint-induced stress that is not due to a sedative action

  15. Subchronic nandrolone administration reduces cardiac oxidative markers during restraint stress by modulating protein expression patterns.

    Science.gov (United States)

    Pergolizzi, Barbara; Carriero, Vitina; Abbadessa, Giuliana; Penna, Claudia; Berchialla, Paola; De Francia, Silvia; Bracco, Enrico; Racca, Silvia

    2017-10-01

    Nandrolone decanoate (ND), an anabolic-androgenic steroid prohibited in collegiate and professional sports, is associated with detrimental cardiovascular effects through redox-dependent mechanisms. We previously observed that high-dose short-term ND administration (15 mg/kg for 2 weeks) did not induce left heart ventricular hypertrophy and, paradoxically, improved postischemic response, whereas chronic ND treatment (5 mg/kg twice a week for 10 weeks) significantly reduced the cardioprotective effect of postconditioning, with an increase in infarct size and a decrease in cardiac performance. We wanted to determine whether short-term ND administration could affect the oxidative redox status in animals exposed to acute restraint stress. Our hypothesis was that, depending on treatment schedule, ND may have a double-edged sword effect. Measurement of malondialdehyde and 4-hydroxynonenal, two oxidative stress markers, in rat plasma and left heart ventricular tissue, revealed that the levels of both markers were increased in animals exposed to restraint stress, whereas no increase in marker levels was noted in animals pretreated with ND, indicating a possible protective action of ND against stress-induced oxidative damage. Furthermore, isolation and identification of proteins extracted from the left heart ventricular tissue samples of rats pretreated or not with ND and exposed to acute stress showed a prevalent expression of enzymes involved in amino acid synthesis and energy metabolism. Among other proteins, peroxiredoxin 6 and alpha B-crystallin, both involved in the oxidative stress response, were predominantly expressed in the left heart ventricular tissues of the ND-pretreated rats. In conclusion, ND seems to reduce oxidative stress by inducing the expression of antioxidant proteins in the hearts of restraint-stressed animals, thus contributing to amelioration of postischemic heart performance.

  16. Restriction on Restraints in the Care for People With Intellectual Disabilities in the Netherlands: Lessons Learned from Australia, UK, and United States

    NARCIS (Netherlands)

    Romijn, A.; Frederiks, B.J.M.

    2012-01-01

    In the Netherlands, physical/mechanical restraints in the care provided to people with intellectual disabilities are still in use, with the case of "Brandon" being a recent and illustrative example. The public debate that this case triggered raised questions concerning the policy proposal in the

  17. Sensitization of restraint-induced corticosterone secretion after chronic restraint in rats: Involvement of 5-HT7 receptors

    Science.gov (United States)

    García-Iglesias, Brenda B.; Mendoza-Garrido, María E.; Gutiérrez-Ospina, Gabriel; Rangel-Barajas, Claudia; Noyola-Díaz, Martha; Terrón, José A.

    2013-01-01

    Serotonin (5-HT) modulates the hypothalamic-pituitary-adrenal (HPA) axis response to stress. We examined the effect of chronic restraint stress (CRS; 20 min/day) as compared to control (CTRL) conditions for 14 days, on: 1) restraint-induced ACTH and corticosterone (CORT) secretion in rats pretreated with vehicle or SB-656104 (a 5-HT7 receptor antagonist); 2) 5-HT7 receptor-like immunoreactivity (5-HT7-LI) and protein in the hypothalamic paraventricular nucleus (PVN) and adrenal glands (AG); 3) baseline levels of 5-HT and 5-hydroxyindolacetic acid (5-HIAA), and 5-HIAA/5-HT ratio in PVN and AG; and 4) 5-HT-like immunoreactivity (5-HT-LI) in AG and tryptophan hydroxylase (TPH) protein in PVN and AG. On day 15, animals were subdivided into Treatment and No treatment groups. Treatment animals received an i.p. injection of vehicle or SB-656104; No Treatment animals received no injection. Sixty min later, Treatment animals were either decapitated with no further stress (0 min) or submitted to acute restraint (10, 30, 60 or 120 min); hormone serum levels were measured. No Treatment animals were employed for the rest of measurements. CRS decreased body weight gain and increased adrenal weight. In CTRL animals, acute restraint increased ACTH and CORT secretion in a time of restraint-dependent manner; both responses were inhibited by SB-656104. Exposure to CRS abolished ACTH but magnified CORT responses to restraint as compared to CTRL conditions; SB-656104 had no effect on ACTH levels but significantly inhibited sensitized CORT responses. In CTRL animals, 5-HT7-LI was detected in magnocellular and parvocellular subdivisions of PVN and sparsely in adrenal cortex. Exposure to CRS decreased 5-HT7-LI and protein in the PVN, but increased 5-HT7-LI in the adrenal cortex and protein in whole AG. Higher 5-HT and 5-HIAA levels were detected in PVN and AG from CRS animals but 5-HIAA/5-HT ratio increased in AG only. Finally, whereas 5-HT-LI was sparsely observed in the adrenal cortex

  18. Influence of time dependent longitudinal magnetic fields on the cooling process, exchange bias and magnetization reversal mechanism in FM core/AFM shell nanoparticles: a Monte Carlo study.

    Science.gov (United States)

    Yüksel, Yusuf; Akıncı, Ümit

    2016-12-07

    Using Monte Carlo simulations, we have investigated the dynamic phase transition properties of magnetic nanoparticles with ferromagnetic core coated by an antiferromagnetic shell structure. Effects of field amplitude and frequency on the thermal dependence of magnetizations, magnetization reversal mechanisms during hysteresis cycles, as well as on the exchange bias and coercive fields have been examined, and the feasibility of applying dynamic magnetic fields on the particle have been discussed for technological and biomedical purposes.

  19. Moderation: an alternative to restraint as a mode of weight self-regulation.

    Science.gov (United States)

    Stotland, S

    2012-12-01

    This study considered two types of eating and weight self-regulation, in five groups, including four types of weight controllers and one non-dieting group. New scales were developed to measure eating moderation and restraint. Moderation was largely uncorrelated with restraint in 4 groups and had a fairly strong positive relation in 1 group. The moderation scale was unrelated to the Dutch Eating Behavior Questionnaire (DEBQ) restraint scale and the Three Factor Eating Questionnaire (TFEQ) rigid restraint subscale and weakly positively related to TFEQ flexible restraint. The restraint scale was strongly correlated to the DEBQ restraint scale, and to both flexible and rigid restraint subscales of the TFEQ. Across the five groups, moderation had exclusively positive relationships with attitude, behavior and emotion variables, while restraint had primarily negative relationships. The study supports moderation as a new dimension of weight self-regulation, independent of restraint. The new measures of moderation and restraint can be used together in research on the processes of change in weight management. Copyright © 2012 Elsevier Ltd. All rights reserved.

  20. Real-time adjustment of ventricular restraint therapy in heart failure.

    Science.gov (United States)

    Ghanta, Ravi K; Lee, Lawrence S; Umakanthan, Ramanan; Laurence, Rita G; Fox, John A; Bolman, Ralph Morton; Cohn, Lawrence H; Chen, Frederick Y

    2008-12-01

    Current ventricular restraint devices do not allow for either the measurement or adjustment of ventricular restraint level. Periodic adjustment of restraint level post-device implantation may improve therapeutic efficacy. We evaluated the feasibility of an adjustable quantitative ventricular restraint (QVR) technique utilizing a fluid-filled polyurethane epicardial balloon to measure and adjust restraint level post-implantation guided by physiologic parameters. QVR balloons were implanted in nine ovine with post-infarction dilated heart failure. Restraint level was defined by the maximum restraint pressure applied by the balloon to the epicardium at end-diastole. An access line connected the balloon lumen to a subcutaneous portacath to allow percutaneous access. Restraint level was adjusted while left ventricular (LV) end-diastolic volume (EDV) and cardiac output was assessed with simultaneous transthoracic echocardiography. All nine ovine successfully underwent QVR balloon implantation. Post-implantation, restraint level could be measured percutaneously in real-time and dynamically adjusted by instillation and withdrawal of fluid from the balloon lumen. Using simultaneous echocardiography, restraint level could be adjusted based on LV EDV and cardiac output. After QVR therapy for 21 days, LV EDV decreased from 133+/-15 ml to 113+/-17 ml (p<0.05). QVR permits real-time measurement and physiologic adjustment of ventricular restraint therapy after device implantation.

  1. Restraint use in older adults in home care: A systematic review.

    Science.gov (United States)

    Scheepmans, Kristien; Dierckx de Casterlé, Bernadette; Paquay, Louis; Milisen, Koen

    2018-03-01

    To get insight into restraint use in older adults receiving home care and, more specifically, into the definition, prevalence and types of restraint, as well as the reasons for restraint use and the people involved in the decision-making process. Systematic review. Four databases (i.e. Pubmed, CINAHL, Embase, Cochrane Library) were systematically searched from inception to end of April 2017. The study encompassed qualitative and quantitative research on restraint use in older adults receiving home care that reported definitions of restraint, prevalence of use, types of restraint, reasons for use or the people involved. We considered publications written in English, French, Dutch and German. One reviewer performed the search and made the initial selection based on titles and abstracts. The final selection was made by two reviewers working independently; they also assessed study quality. We used an integrated design to synthesise the findings. Eight studies were reviewed (one qualitative, seven quantitative) ranging in quality from moderate to high. The review indicated there was no single, clear definition of restraint. The prevalence of restraint use ranged from 5% to 24.7%, with various types of restraint being used. Families played an important role in the decision-making process and application of restraints; general practitioners were less involved. Specific reasons, other than safety for using restraints in home care were noted (e.g. delay to nursing home admission; to provide respite for an informal caregiver). Contrary to the current socio demographical evolutions resulting in an increasing demand of restraint use in home care, research on this subject is still scarce and recent. The limited evidence however points to the challenging complexity and specificity of home care regarding restraint use. Given these serious challenges for clinical practice, more research about restraint use in home care is urgently needed. Copyright © 2017. Published by Elsevier

  2. Cell type-specific sorting of neuropeptides : a mechanism to modulate peptide composition of large dense core vesicles

    NARCIS (Netherlands)

    Klumperman, J.; Spijker, S.; Minnen, J. van; Sharp-Baker, H.; Smit, A.B.; Geraerts, W.P.M.

    1996-01-01

    The CNS of Lymnaea stagnalis contains two populations of egg-laying hormone (ELH)-producing neurons that differ in size and topology. In type I neurons, all peptides located C-terminally from the cleavage site Arg-Ser-Arg-Arg180-183 are sorted into secretory large dense-core vesicles (LDCV), whereas

  3. Hormonal and molecular effects of restraint stress on formalin-induced pain-like behavior in male and female mice.

    Science.gov (United States)

    Long, Caela C; Sadler, Katelyn E; Kolber, Benedict J

    2016-10-15

    The evolutionary advantages to the suppression of pain during a stressful event (stress-induced analgesia (SIA)) are obvious, yet the reasoning behind sex-differences in the expression of this pain reduction are not. The different ways in which males and females integrate physiological stress responses and descending pain inhibition are unclear. A potential supraspinal modulator of stress-induced analgesia is the central nucleus of the amygdala (CeA). This limbic brain region is involved in both the processing of stress and pain; the CeA is anatomically and molecularly linked to regions of the hypothalamic pituitary adrenal (HPA) axis and descending pain network. The CeA exhibits sex-based differences in response to stress and pain that may differentially induce SIA in males and females. Here, sex-based differences in behavioral and molecular indices of SIA were examined following noxious stimulation. Acute restraint stress in male and female mice was performed prior to intraplantar injections of formalin, a noxious inflammatory agent. Spontaneous pain-like behaviors were measured for 60min following formalin injection and mechanical hypersensitivity was evaluated 120 and 180min post-injection. Restraint stress altered formalin-induced spontaneous behaviors in male and female mice and formalin-induced mechanical hypersensitivity in male mice. To assess molecular indices of SIA, tissue samples from the CeA and blood samples were collected at the 180min time point. Restraint stress prevented formalin-induced increases in extracellular signal regulated kinase 2 (ERK2) phosphorylation in the male CeA, but no changes associated with pERK2 were seen with formalin or restraint in females. Sex differences were also seen in plasma corticosterone concentrations 180min post injection. These results demonstrate sex-based differences in behavioral, molecular, and hormonal indices of acute stress in mice that extend for 180min after stress and noxious stimulation. Copyright

  4. Mechanisms and Effects on HBV Replication of the Interaction between HBV Core Protein and Cellular Filamin B.

    Science.gov (United States)

    Li, Yilin; Sun, Yishuang; Sun, Fuyun; Hua, Rong; Li, Chenlin; Chen, Lang; Guo, Deyin; Mu, Jingfang

    2018-03-28

    Hepatitis B virus (HBV) infection is one of the major problems that threatens global health. There have been many studies on HBV, but the relationship between HBV and host factors is largely unexplored and more studies are needed to clarify these interactions. Filamin B is an actin-binding protein that acts as a cytoskeleton protein, and it is involved in cell development and several signaling pathways. In this study, we showed that filamin B interacted with HBV core protein, and the interaction promoted HBV replication. The interaction between filamin B and core protein was observed in HEK 293T, Huh7 and HepG2 cell lines by co-immunoprecipitation and co-localization immnofluoresence. Overexpression of filamin B increased the levels of HBV total RNAs and pre-genome RNA (pgRNA), and improved the secretion level of hepatitis B surface antigen (HBsAg) and hepatitis B e antigen (HBeAg). In contrast, filamin B knockdown inhibited HBV replication, decreased the level of HBV total RNAs and pgRNA, and reduced the secretion level of HBsAg and HBeAg. In addition, we found that filamin B and core protein may interact with each other via four blocks of argentine residues at the C-terminus of core protein. In conclusion, we identify filamin B as a novel host factor that can interact with core protein to promote HBV replication in hepatocytes. Our study provides new insights into the relationship between HBV and host factors and may provide new strategies for the treatment of HBV infection.

  5. Rapid Synthesis and Formation Mechanism of Core-Shell-Structured La-Doped SrTiO3 with a Nb-Doped Shell

    Directory of Open Access Journals (Sweden)

    Nam-Hee Park

    2015-07-01

    Full Text Available To provide a convenient and practical synthesis process for metal ion doping on the surface of nanoparticles in an assembled nanostructure, core-shell-structured La-doped SrTiO3 nanocubes with a Nb-doped surface layer were synthesized via a rapid synthesis combining a rapid sol-precipitation and hydrothermal process. The La-doped SrTiO3 nanocubes were formed at room temperature by a rapid dissolution of NaOH pellets during the rapid sol-precipitation process, and the Nb-doped surface (shell along with Nb-rich edges formed on the core nanocubes via the hydrothermal process. The formation mechanism of the core-shell-structured nanocubes and their shape evolution as a function of the Nb doping level were investigated. The synthesized core-shell-structured nanocubes could be arranged face-to-face on a SiO2/Si substrate by a slow evaporation process, and this nanostructured 10 μm thick thin film showed a smooth surface.

  6. Composites Based on Core-Shell Structured HBCuPc@CNTs-Fe3O4 and Polyarylene Ether Nitriles with Excellent Dielectric and Mechanical Properties

    Science.gov (United States)

    Pu, Zejun; Zhong, Jiachun; Liu, Xiaobo

    2017-10-01

    Core-shell structured magnetic carbon nanotubes (CNTs-Fe3O4) coated with hyperbranched copper phthalocyanine (HBCuPc) (HBCuPc@CNTs-Fe3O4) hybrids were prepared by the solvent-thermal method. The results indicated that the HBCuPc molecules were decorated on the surface of CNTs-Fe3O4 through coordination behavior of phthalocyanines, and the CNTs-Fe3O4 core was completely coaxial wrapped by a functional intermediate HBCuPc shell. Then, polymer-based composites with a relatively high dielectric constant and low dielectric loss were fabricated by using core-shell structured HBCuPc@CNTs-Fe3O4 hybrids as fillers and polyarylene ether nitriles (PEN) as the polymer matrix. The cross-sectional scanning electron microscopy (SEM) images of composites showed that there is almost no agglomeration and internal delamination. In addition, the rheological analysis reveals that the core-shell structured HBCuPc@CNTs-Fe3O4 hybrids present better dispersion and stronger interface adhesion with the PEN matrix than CNTs-Fe3O4, thus resulting in significant improvement of the mechanical, thermal and dielectric properties of polymer-based composites.

  7. Poor compliance with child safety restraint use while travelling.

    LENUS (Irish Health Repository)

    Fallon, R

    2011-02-01

    Road traffic accidents are a leading cause of death of children. It is the law that all children should be appropriately secured when traveling in vehicles. The aim of this study was to evaluate parental conformity with these regulations and to test if advice given at a Paediatric outpatient clinic could improve compliance. Two groups were assigned, an intervention group (parents given an information leaflet and a clear explanation about appropriate restraints for their children) and a non-intervention group (received no information). They were contacted again after 2 months and asked regarding compliance. A total of 394 children from 186 families were initially given the questionnaire. Nearly one third of children (29.2%) were not using any restraint while travelling rising to 35.3% on follow up. This study concluded that once off parental education made negligible difference to an already inconsistent and haphazard approach to compliance with safety regulations.

  8. Coping with budget restraint in a Scandinavian welfare state

    DEFF Research Database (Denmark)

    Nielsen, Annemette Ljungdalh; Holm, Lotte; Lund, Thomas Bøker

    2015-01-01

    The purpose of this study was to investigate how different types of households react to experiences of food budget restraint in Denmark. The study applied a mixed method design, based on survey data and on qualitative interviews. The qualitative data source consisted of interviews with 30...... institute GfK ConsumerTracking Scandinavia. Using both data sources the study explored how shopping, storing, cooking and eating practices changed as a consequence of experienced restraints on the food budget. The quantitative results revealed how differences in terms of application of various types...... of strategies are related to different levels of food budget restrictions. Strategies applied to storing and cooking food in more efficient manners were widely practiced across all groups. Strategies which affected eating experiences, such as compromising the tastiness of food and giving up social ties involved...

  9. Polyacrylonitrile/polyaniline core/shell nanofiber mat for removal of hexavalent chromium from aqueous solution: mechanism and applications

    KAUST Repository

    Wang, Jianqiang

    2013-01-01

    Polyacrylonitrile/polyaniline core/shell nanofibers were prepared via electrospinning followed by in situ polymerization of aniline. Nanofibers with different morphology were obtained by changing the polymerization temperature. When used as absorbent for Cr(vi) ions, the core/shell nanofiber mats exhibit excellent adsorption capability. The equilibrium capacity is 24.96, 37.24, and 52.00 mg g-1 for 105, 156, and 207 mg L-1 initial Cr(vi) solution, respectively, and the adsorption capacity increases with temperature. The adsorption follows a pseudo second order kinetics model and is best fit using the Langmuir isotherm model. The mats show excellent selectivity towards Cr(vi) ions in the presence of competing ions albeit a small decrease in adsorption is observed. The mats can be regenerated and reused after treatment with NaOH making them promising candidates as practical adsorbents for Cr(vi) removal. © The Royal Society of Chemistry 2013.

  10. Mechanism for radiative recombination and defect properties of GaP/GaNP core/shell nanowires

    International Nuclear Information System (INIS)

    Dobrovolsky, A.; Stehr, J. E.; Chen, S. L.; Chen, W. M.; Buyanova, I. A.; Kuang, Y. J.; Sukrittanon, S.; Tu, C. W.

    2012-01-01

    Recombination processes in GaP/GaNP core/shell nanowires (NWs) grown on a Si substrate by molecular beam epitaxy are examined using a variety of optical characterization techniques, including cw- and time-resolved photoluminescence and optically detected magnetic resonance (ODMR). Superior optical quality of the structures is demonstrated based on the observation of intense emission from a single NW at room temperature. This emission is shown to originate from radiative transitions within N-related localized states. From ODMR, growth of GaP/GaNP NWs is also found to facilitate formation of complex defects containing a P atom at its core that act as centers of competing non-radiative recombination.

  11. New enhancement mechanism of the transitions in the Earth of the solar and atmospheric neutrinos crossing the Earth core

    International Nuclear Information System (INIS)

    Petcov, S.T.

    1999-01-01

    It is shown that the ν 2 → ν e and ν μ → ν e (ν e → ν μ(τ) ) transitions respectively of the solar and atmospheric neutrinos in the Earth in the case of ν e - ν μ(τ) mixing in vacuum, are strongly enhanced by a new type of resonance when the neutrinos cross the Earth core. The resonance is operative at small mixing angles but differs from the MSW one. It is in many respects similar to the electron paramagnetic resonance taking place in a specific configuration of two magnetic fields. The conditions for existence of the new resonance include, in particular, specific constraints on the neutrino oscillation lengths in the Earth mantle and in the Earth core, thus the resonance is a 'neutrino oscillation length resonance'. It leads also to enhancement of the ν 2 → ν e and ν e → ν s transitions in the case of ν e - ν s mixing and of the ν-bar s (or ν μ → ν s ) transitions at small mixing angles. The presence of the neutrino oscillation length resonance in the transitions of solar and atmospheric neutrinos traversing the Earth core has important implications for current and future solar and atmospheric neutrino experiments, and more specifically, for the interpretation of the results of the Super-Kamiokande experiment

  12. Construct Validation of the Portuguese Version of the Restraint Scale

    Directory of Open Access Journals (Sweden)

    João Carvalho

    2016-08-01

    Full Text Available AimThe main purpose of this study was to adapt the Restraint Scale (RS to Portuguese and examine its psychometric properties, specifically its construct validity.MethodIn this study, 238 normal-weight adults (82% women; Mean age = 36.6, SD = 15.0 participated in an online survey containing measures of Restraint Scale, Three Factor Eating Questionnaire, Dutch Eating Behaviour Questionnaire, and Body Dissatisfaction and Drive for Thinness scales.ResultsExploratory factor analyses corroborated the two-factors structure found in previous studies, in particular when three items without clear factorial assignment and low correlation were excluded. A final two-factors version of the RS containing seven items presented a very good fit to the measurement model and good internal consistency. Confirmatory factor analysis of the 7-items RS in relation to a three-factor model of overeating, dieting and body dissatisfaction measures revealed that the RS was the only restraint measure loading in all three factors.ConclusionThis suggests that the 7-items Portuguese version of the RS has good psychometric properties and unique features that lend it appropriate to identify and study unsuccessful chronic dieters.

  13. STS-102 Onboard Photograph-The Payload Equipment Restraint System

    Science.gov (United States)

    2001-01-01

    In this Space Shuttle STS-102 mission image, the Payload Equipment Restraint System H-Strap is shown at the left side of the U.S. Laboratory hatch and behind Astronaut James D. Weatherbee, mission specialist. PERS is an integrated modular system of components designed to assist the crew of the International Space Station (ISS) in restraining and carrying necessary payload equipment and tools in a microgravity environment. The Operations Development Group, Flight Projects Directorate at the Marshall Space Flight Center (MSFC), while providing operation support to the ISS Materials Science Research Facility (MSRF), recognized the need for an on-orbit restraint system to facilitate control of lose objects, payloads, and tools. The PERS is the offspring of that need and it helps the ISS crew manage tools and rack components that would otherwise float away in the near-zero gravity environment aboard the Space Station. The system combines Kevlar straps, mesh pockets, Velcro and a variety of cornecting devices into a portable, adjustable system. The system includes the Single Strap, the H-Strap, the Belly Pack, the Laptop Restraint Belt, and the Tool Page Case. The Single Strap and the H-Strap were flown on this mission. The PERS concept was developed by industrial design students at Auburn University and the MSFC Flight Projects Directorate.

  14. Restraint reduction in a nursing home and its impact on employee attitudes.

    Science.gov (United States)

    Sundel, M; Garrett, R M; Horn, R D

    1994-04-01

    To reduce physical restraint use in a nursing home and increase employee support for the restraint-reduction program. A one-group pretest-posttest design with repeated measures was used to determine changes in restraint use with participants over a 14-month interval. All individuals employed at the nursing home were surveyed at two time periods to determine their opinions on restraint use. A 265-bed private, non-profit nursing home in Dallas, Texas. A restrained cohort of 170 residents with a mean age of 84 years; 84% were female. A total of 182 employees participated in the first survey and 209 in the second. Formation of a project team that planned and supervised restraint removal. Inservice training on restraint use was conducted for all employees. Type and frequency of restraint use among the restrained cohort at four evaluation points within a 14-month interval. The frequency of restraint use in the nursing home population was also recorded. Survey measures included employee responses to a 16-item closed-end questionnaire before and after training. The mean number of restraints used with each resident in the restrained cohort decreased from 1.56 to 0.67. The number of residents on restraints in the nursing home was reduced during the course of the study (67.5% vs. 36.7%, P reduction program in a nursing home can produce positive results in terms of decreased restraint use and supportive employee attitudes. More practical alternatives to restraints need to be developed for application in the training of nursing home employees. Future studies on resident, employee, and family attitudes about restraint use are suggested.

  15. Allopregnanolone's attenuation of the lordosis-inhibiting effects of restraint is blocked by the antiprogestin, CDB-4124.

    Science.gov (United States)

    Uphouse, Lynda; Hiegel, Cindy

    2014-07-01

    A brief restraint experience reduces lordosis behavior in ovariectomized females that have been hormonally primed with estradiol benzoate. The addition of progesterone to the priming prevents the lordosis inhibition. Based on prior studies with an inhibitor of progesterone metabolism, we have implicated the intracellular progesterone receptor, rather than progesterone metabolites, as responsible for this protection. However, the progesterone metabolite, allopregnanolone (3α-hydroxy-5α-pregnan-20-one), also prevents lordosis inhibition after restraint. In a prior study, we reported that the progestin receptor antagonist, RU486 (11β-(4-dimethylamino)phenyl-17β-hydroxy-17-(1-propynyl)estra-4,9-dien-3-one), attenuated the effect of allopregnanolone. Because RU486 can also block the glucocorticoid receptor, in the current studies, we evaluated the effect of the progestin receptor antagonist, CDB-4124 (17α-acetoxy-21-methoxy-11β-[4-N,N-dimethyaminopheny]-19-norpregna-4,9-dione-3,20-dione), which is relatively devoid of antiglucocorticoid activity. Ovariectomized, Fischer rats were injected with 10 μg estradiol benzoate. Two days later, rats received either 60 mg/kg CDB-4124 or 20% DMSO/propylene glycol vehicle 1 h before injection with 4 mg/kg allopregnanolone. After a pretest to confirm sexual receptivity, rats were restrained for 5min and immediately tested for sexual behavior. Lordosis behavior was reduced by the restraint and attenuated by allopregnanolone. Pretreatment with CDB-4124 reduced allopregnanolone's effect. These findings support prior suggestions that allopreganolone reduces the response to restraint by mechanisms that require activation of the intracellular progesterone receptor. Copyright © 2014 Elsevier Inc. All rights reserved.

  16. ALLOPREGNANOLONE’S ATTENUATION OF THE LORDOSIS-INHIBITNG EFFECTS OF RESTRAINT IS BLOCKED BY THE ANTIPROGESTIN, CDB-4124

    Science.gov (United States)

    Uphouse, Lynda; Hiegel, Cindy

    2014-01-01

    A brief restraint experience reduces lordosis behavior in ovariectomized females that have been hormonally primed with estradiol benzoate. The addition of progesterone to the priming prevents the lordosis inhibition. Based on prior studies with an inhibitor of progesterone metabolism, we have implicated the intracellular progesterone receptor, rather than progesterone metabolites, as responsible for this protection. However, the progesterone metabolite, allopregnanolone (3α-hydroxy-5α-pregnan-20-one), also prevents lordosis inhibition after restraint. In a prior study, we reported that the progestin receptor antagonist, RU486 (11β-(4-dimethylamino)phenyl-17β-hydroxy-17-(1-propynyl)estra-4,9-dien-3-one), attenuated the effect of allopregnanolone. Because RU486 can also block the glucocorticoid receptor, in the current studies, we evaluated the effect of the progestin receptor antagonist, CDB-4124 (17 α-acetoxy-21-methoxy-11β-[4-N,N-dimethyaminopheny]-19-norpregna-4,9-dione-3,20-dione), which is relatively devoid of antiglucocorticoid activity. Ovariectomized, Fischer rats were injected with 10 μg estradiol benzoate. Two days later, rats received either 60 mg/kg CDB-4124 or the 20% DMSO/propylene glycol vehicle 1 hr before injection with 4 mg/kg allopregnanolone. After a pretest to confirm sexual receptivity, rats were restrained for 5 min and immediately tested for sexual behavior. Lordosis behavior was reduced by the restraint and attenuated by allopregnanolone. Pretreatment with CDB-4124 reduced allopregnanolone’s effect. These findings support prior suggestions that allopreganolone reduces the response to restraint by mechanisms that require activation of the intracellular progesterone receptor. PMID:24650591

  17. An analysis of fast reactor fuel assembly performance taking into account their mechanical interaction in the core and refuelling line capabilities

    International Nuclear Information System (INIS)

    Buksha, Yu.K.; Zabudko, L.M.; Kravchenko, I.N.; Matveenko, L.V.; Meshkov, M.N.

    1984-01-01

    An approach to assessment of fast reactor fuel assembly performance has been considered. A concept of passive restraint of fuel assemblies in a reactor adopted in the USSR is described. Some methods for calculating the interassembly interactions during operation are briefly outlined, some calculated results are presented. A problem of fuel assembly performance during refuelling taking into account the refuelling line capabilities is considered. Some results from fuel assemblies operation experience in the BN-600 reactor are given. (author)

  18. Behavioral effects of acclimatization to restraint protocol used for awake animal imaging.

    Science.gov (United States)

    Reed, Michael D; Pira, Ashley S; Febo, Marcelo

    2013-07-15

    Functional MRI in awake rats involves acclimatization to restraint to minimize motion. We designed a study to examine the effects of an acclimatization protocol (5 days of restraint, 60 min per day) on the emission of 22-kHz ultrasonic vocalizations and performance in a forced swim test (FST). Our results showed that USV calls are reduced significantly by days 3, 4 and 5 of acclimatization. Although the rats showed less climbing activity (and more immobility) in FST on day 5 compared to the 1st day of restraint acclimatization, the difference was not detected once the animals were given a 2-week hiatus. Overall, we showed that animals adapt to the restraint over a five-day period; however, restraint may introduce confounding behavioral outcomes that may hinder the interpretation of results derived from awake rat imaging. The present data warrants further testing of the effects of MRI restraint on behavior. Copyright © 2013 Elsevier B.V. All rights reserved.

  19. Dietary restraint, anxiety, and the relative reinforcing value of snack food in non-obese women.

    Science.gov (United States)

    Goldfield, Gary S; Legg, Christine

    2006-11-01

    This study tested the independent and interactive effects of anxiety and dietary restraint on the relative reinforcing value of snack food. Thirty non-obese, female university students were assigned to one of four groups based on median split scores on measures of dietary restraint and state-anxiety: low-restraint/low-anxiety (n=7), low-restraint/high-anxiety (n=7), high-restraint/low-anxiety (n=9), and high-restraint/high-anxiety (n=7). Participants were provided the choice to earn points for palatable snack foods or fruits and vegetables using a computerized concurrent schedules choice task. The behavioural cost to gain access to snack foods increased across trials, whereas the cost to gain access to fruits and vegetables was held constant across trials. The relative reinforcing value of palatable snack food in relation to fruits and vegetables was defined as the total amount of points earned for snack food. Two-way analysis of covariance, with hunger and hedonic snack food ratings as covariates, showed that dietary restraint and anxiety had a significant interactive effect on the relative reinforcing value of snack food, indicating that the effect of anxiety on snack food reinforcement is moderated by dietary restraint. Specifically, the high-anxiety/low-restraint women found snack food significantly less reinforcing than low-anxiety/low-restraint women, but no differences emerged between high- and low-anxiety women with high-restraint. Neither restraint nor anxiety had an independent effect on the relative reinforcing value of snack food. These findings indicate that anxiety may have a suppressive effect on the relative reinforcing value of snack food in low-restrained eaters, but not an enhancing effect on snack food reinforcement in high-restrained eaters. Clinical implications of these findings are discussed.

  20. Evaluation of the influence of seismic restraint characteristics on breeder reactor piping systems

    International Nuclear Information System (INIS)

    Mello, R.M.; Pollono, L.P.

    1979-01-01

    For the Clinch River Breeder Reactor Plant (CRBRP) heat transport system piping within the reactor containment building, dynamic analyses of the piping loops have been performed to study the effect of restraint stiffness on the dynamic behavior of the piping. In addition, analysis and testing of typical CRBRP restraint system components have been performed for the purpose of quantifying and verifying the basic characteristics of the restraints used in the piping system dynamic analysis

  1. The detrimental effects of physical restraint as a consequence for inappropriate classroom behavior.

    Science.gov (United States)

    Magee, S K; Ellis, J

    2001-01-01

    Functional analyses produced inconclusive results regarding variables that maintained problem behavior for 2 students with developmental disabilities. Procedures were modified to include a contingent physical restraint condition based on in-class observations. Results indicated that tinder conditions in which physical restraint (i.e., basket-hold timeout) was applied contingent on problem behavior, rates of these behaviors increased across sessions for both subjects. Implications for the use of physical restraint in the classroom are discussed.

  2. Use of physical restraint: Nurses' knowledge, attitude, intention and practice and influencing factors.

    Science.gov (United States)

    Eskandari, Fatemeh; Abdullah, Khatijah Lim; Zainal, Nor Zuraida; Wong, Li Ping

    2017-12-01

    To investigate the knowledge, attitude, intention and practice of nurses towards physical restraint and factors influencing these variables. A literature review showed a lack of studies focused on the intention of nurses regarding physical restraint throughout the world. Considering that very little research on physical restraint use has been carried out in Malaysia, assessment of nurses' knowledge, attitude, intention and practice is necessary before developing a minimising programme in hospitals. A cross-sectional study was used. A questionnaire to assess the knowledge, attitude, intention and practice was completed by all nurses (n = 309) in twelve wards of a teaching hospital in Kuala Lumpur. Moderate knowledge and attitude with strong intention to use physical restraint were found among the nurses. Less than half of nurses considered alternatives to physical restraint and most of them did not understand the reasons for the physical restraint. Nurses' academic qualification, read any information source during past year and nurses' work unit showed a significant association with nurses' knowledge. Multiple linear regression analysis found knowledge, attitude and intention were significantly associated with nurses' practice to use physical restraint. This study showed some important misunderstandings of nurses about using physical restraint and strong intention regarding using physical restraint. Findings of this study serve as a supporting reason for importance of educating nurses about the use of physical restraint. Exploring the knowledge, attitude, intention and current practice of nurses towards physical restraint is important so that an effective strategy can be formulated to minimise the use of physical restraints in hospitals. © 2017 John Wiley & Sons Ltd.

  3. Analysis of fluid-structure interaction mechanism of a Na-FBR core while the evacuation of a gas pocket

    International Nuclear Information System (INIS)

    Sargentini, Lucia

    2014-01-01

    The purpose of this study is to improve the knowledge about the core behavior of a sodium fast breeder reactor (Na-FBR) during vibrations through the fluid-structure interaction analysis. Namely, we investigate the flowering of the Phenix core during the SCRAM for negative reactivity (AURN) and the seismic behavior of the core of Astrid project. Three approaches are followed: experimental campaign, performing of analytical solution and development of numerical model. We create a flow regime map to identify the flow regimes in the fluid gap for very short times scales (as AURN) as well as longer time scales (as seismic oscillations). The most suitable equation system (Navier-Stokes, Euler or linearized Euler) is chosen to model the fluid flow in the numerical code. To our knowledge, for the first time, an analytical solution for free vibration and very narrow gaps is proposed. We designed two experimental apparatus (PISE-1a and PISE-2c) composed respectively by 1 and 19 hexagonal assemblies (two crowns) of Poly-methyl methacrylate (PMMA). Every PMMA assembly is fixed to a stainless steel twin-blades support allowing only orthogonal oscillations with respect to generating line of assembly. The twin-blades supports are designed to give the same range frequency of Phenix assembly in liquid sodium. The experimental equipment PISE-1a is used to determine the dynamic characteristics of PISE-2c assembly, to calibrate instrumentation and for validating our numerical model. Free vibration tests in air are performed to evaluate the dynamic characteristics of the body. Free vibration experiments in water allow to assess the added mass and added damping effect on the frequency. Even though the fluid flow during vibration should be completely bidimensional, the fluid flow is affected by a 3D effect - named 'jambage' - at the top and the basis of the assembly. This effect produces a lower frequency than the theoretical value. Tests are modeled with a bidimensional

  4. A self-medication hypothesis for increased vulnerability to drug abuse in prenatally restraint stressed rats.

    Science.gov (United States)

    Reynaert, Marie-Line; Marrocco, Jordan; Gatta, Eleonora; Mairesse, Jérôme; Van Camp, Gilles; Fagioli, Francesca; Maccari, Stefania; Nicoletti, Ferdinando; Morley-Fletcher, Sara

    Stress-related events that occur in the perinatal period can permanently change brain and behavior of the developing individual and there is increasing evidence that early-life adversity is a contributing factor in the etiology of drug abuse and mood disorders. Neural adaptations resulting from early-life stress may mediate individual differences in novelty responsiveness and in turn contribute to drug abuse vulnerability. Prenatal restraint stress (PRS) in rats is a well-documented model of early stress known to induce long-lasting neurobiological and behavioral alterations including impaired feedback mechanisms of the HPA axis, enhanced novelty seeking, and increased sensitiveness to psychostimulants as well as anxiety/depression-like behavior. Together with the HPA axis, functional alterations of the mesolimbic dopamine system and of the metabotropic glutamate receptors system appear to be involved in the addiction-like profile of PRS rats.

  5. Increase in best practice child car restraint use for children aged 2-5 years in low socioeconomic areas after introduction of mandatory child restraint laws.

    Science.gov (United States)

    Brown, Julie; Keay, Lisa; Hunter, Kate; Bilston, Lynne E; Simpson, Judy M; Ivers, Rebecca

    2013-06-01

    To examine changes in child car restraint practices in low socioeconomic areas following the introduction of mandatory child car restraint legislation in New South Wales (NSW), Australia. Data from two cross-sectional studies of child car restraint use at pre-schools, early childhood centres and primary schools before and after the introduction of legislating mandatory age-appropriate car restraint use for children up to the age of seven years was used in this analysis. All included observations were from local government areas with socioeconomic status in the lowest 30% of urban Sydney. Children aged 2-5 years were observed in their vehicles as they arrived at observation sites (107 pre-legislation, 360 post-legislation). Multilevel logistic regression was used to examine changes in observed age-appropriate and correct use of car restraints. Age-appropriate car restraint use was higher post-legislation than pre-legislation. After controlling for child's age, parental income, language spoken at home and adjusting for clustering, the odds of children being appropriately restrained post-legislation were 2.3 times higher than in the pre-legislation sample, and the odds of them being correctly restrained were 1.6 times greater. Results indicate an improvement in car restraint practices among children aged 2-5 in low socioeconomic areas after introduction of child restraint laws. Implications : Despite improvements observed with enhanced legislation, further efforts are required to increase optimal child car restraint use. © 2013 The Authors. ANZJPH © 2013 Public Health Association of Australia.

  6. Proteomics Core

    Data.gov (United States)

    Federal Laboratory Consortium — Proteomics Core is the central resource for mass spectrometry based proteomics within the NHLBI. The Core staff help collaborators design proteomics experiments in a...

  7. An alternate and reversible method for flight restraint of cranes.

    Science.gov (United States)

    Zhang, Sen Lin; Yang, Shu Hui; Li, Bing; Xu, Yan Chun; Ma, Jian Hua; Xu, Jian Feng; Zhang, Xian Guang

    2011-01-01

    Flight restraint is important for zoos, safaris, and breeding centers for large birds. Currently used techniques for flight restraint include both surgical and non-surgical approaches. Surgical approaches usually cause permanent change to or removal of tendon, patagial membrane, or wing bones, and can cause pain and inflammation. Non-surgical approaches such as clipping or trimming feathers often alter the bird's appearance, and can damage growing blood feathers in fledglings or cause joint stiffness. We observed microstructure of primary feathers of the red-crowned crane (Grus japonensis) and found that the width of barbs is a determinative factor influencing vane stiffness and geometric parameters. We hypothesized that partial longitudinal excision of barbs on the ventral surface of the primary feathers would reduce the stiffness of the vane and render the feathers unable to support the crane's body weight during flight. Furthermore, we hypothesized that this modification of barbs would also change the aerodynamic performance of feathers such that they could not generate sufficient lift and thrust during flapping to enable the bird to fly. We tested this hypothesis on a red-crowned crane that had normal flight capability by excising the ventral margin of barbs on all 10 primaries on the left wing. The bird was unable to take off until the modified feathers were replaced by new ones. Removal of barbs proved to be a simple, non-invasive, low-cost and reversible method for flight restraint. It is potentially applicable to other large birds with similar structural characteristics of primary feathers. © 2010 Wiley-Liss, Inc.

  8. Dietary restraint and self-discrepancy in male university students.

    Science.gov (United States)

    Orellana, Ligia; Grunert, Klaus G; Sepúlveda, José; Lobos, Germán; Denegri, Marianela; Miranda, Horacio; Adasme-Berríos, Cristian; Mora, Marcos; Etchebarne, Soledad; Salinas-Oñate, Natalia; Schnettler, Berta

    2016-04-01

    Self-discrepancy describes the distance between an ideal and the actual self. Research suggests that self-discrepancy and dietary restraint are related, causing a significant impact on the person's well-being. However, this relationship has been mostly reported in female and mixed populations. In order to further explore dietary behaviors and their relations to self-discrepancy and well-being-related variables in men, a survey was applied to a non-probabilistic sample of 119 male students from five Chilean state universities (mean age=21.8, SD=2.75). The questionnaire included the Revised Restraint Scale (RRS) with the subscales weight fluctuations (WF) and diet concern (DC), the Satisfaction with Life Scale (SWLS), the Satisfaction with Food-Related Life Scale (SWFL), the Nutrition Interest Scale (NIS), and the Self-discrepancy Index (SDI). Questions were asked about socio-demographic characteristics, eating and drinking habits, and approximate weight and height. A cluster analysis applied to the Z-scores of the RRS classified the following typologies: Group 1 (22.7%), men concerned about weight fluctuations; Group 2 (37.0%), men concerned about diet and weight fluctuations; Group 3 (40.3%), unconcerned about diet and weight fluctuations. The typologies differed in their SDI score, restriction on pastry consumption and reported body mass index (BMI). Students with higher DC and WF scores had a higher BMI, and tended to report high self-discrepancy not only on a physical level, but also on social, emotional, economic and personal levels. This study contributes to the literature on subjective well-being, dietary restraint and self-discrepancy in men from non-clinical samples. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. [Therapeutic restraint and freedom of movement, changing practices].

    Science.gov (United States)

    Perrin-Niquet, Annick

    From confinement to the philosophy of care in the community, the history of psychiatry testifies to the evolution of practices in the matter of the restriction of freedom. The French National Health Authority still too often recommends practices based on restraint. Caregivers, in relation to the clinical aspect of the patients, need clearly identified therapeutic projects. While training can be vital for them, risk management policies can prove to be a hindrance to patients' freedom. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  10. Crew Restraint Design for the International Space Station

    Science.gov (United States)

    Norris, Lena; Holden, Kritina; Whitmore, Mihriban

    2006-01-01

    With permanent human presence onboard the International Space Station (ISS), crews will be living and working in microgravity, dealing with the challenges of a weightless environment. In addition, the confined nature of the spacecraft environment results in ergonomic challenges such as limited visibility and access to the activity areas, as well as prolonged periods of unnatural postures. Without optimum restraints, crewmembers may be handicapped for performing some of the on-orbit tasks. Currently, many of the tasks on ISS are performed with the crew restrained merely by hooking their arms or toes around handrails to steady themselves. This is adequate for some tasks, but not all. There have been some reports of discomfort/calluses on the top of the toes. In addition, this type of restraint is simply insufficient for tasks that require a large degree of stability. Glovebox design is a good example of a confined workstation concept requiring stability for successful use. They are widely used in industry, university, and government laboratories, as well as in the space environment, and are known to cause postural limitations and visual restrictions. Although there are numerous guidelines pertaining to ventilation, seals, and glove attachment, most of the data have been gathered in a 1-g environment, or are from studies that were conducted prior to the early 1980 s. Little is known about how best to restrain a crewmember using a glovebox in microgravity. Another ISS task that requires special consideration with respect to restraints is robotic teleoperation. The Robot Systems Technology Branch at the NASA Johnson Space Center is developing a humanoid robot astronaut, or Robonaut. It is being designed to perform extravehicular activities (EVAs) in the hazardous environment of space. An astronaut located inside the ISS will remotely operate Robonaut through a telepresence control system. Essentially, the robot mimics every move the operator makes. This requires the

  11. Restraint behavior of concrete under extreme thermal and hygral conditions

    International Nuclear Information System (INIS)

    Schwesinger, P.; Dommnich, F.

    1989-01-01

    Stresses due to temperature may be a considerable part of the whole loading of the structure especially in reactor vessels, chimneys and other structures. During using of this structures the heating cycle consisting of heating and cooling may be repeated for several times. On the other hand the initial load, the preloading time, the heating rate and the moisture of concrete can differ in respect of the design or utilization of the structure. The effect of this environmental factors on the restraint behavior of concrete is presented in this paper

  12. The core spline method for solution of quantum-mechanical systems of differential equations for bound states

    International Nuclear Information System (INIS)

    Aleksandrov, L.; Drenska, M.; Karadzhov, D.

    1986-01-01

    A generalization of the core spline method is given in the case of solution of the general bound state problem for a system of M linear differential equations with coefficients depending on the spectral parameter. The recursion scheme for construction of basic splines is described. The wave functions are expressed as linear combinations of basic splines, which are approximate partial solutions of the system. The spectral parameter (the eigenvalue) is determined from the condition for existence of a nontrivial solution of a (MxM) linear algebraic system at the last collocation point. The nontrivial solutions of this system determine (M - 1) coefficients of the linear spans, expressing the wave functions. The last unknown coefficient is determined from a boundary (or normalization) condition for the system. The computational aspects of the method are discussed, in particular, its concrete algorithmic realization used in the RODSOL program. The numerical solution of the Dirac system for the bound states of a hydrogen atom is given is an example

  13. Evaluation of Multi Canister Overpack (MCO) Handling Machine Uplift Restraint for a Seismic Event During Repositioning Operations

    International Nuclear Information System (INIS)

    SWENSON, C.E.

    2000-01-01

    Insertion of the Multi-Canister Overpack (MCO) assemblies into the Canister Storage Building (CSB) storage tubes involves the use of the MCO Handling Machine (MHM). During MCO storage tube insertion operations, inadvertent movement of the MHM is prevented by engaging seismic restraints (''active restraints'') located adjacent to both the bridge and trolley wheels. During MHM repositioning operations, the active restraints are not engaged. When the active seismic restraints are not engaged, the only functioning seismic restraints are non-engageable (''passive'') wheel uplift restraints which function only if the wheel uplift is sufficient to close the nominal 0.5-inch gap at the uplift restraint interface. The MHM was designed and analyzed in accordance with ASME NOG-1-1995. The ALSTHOM seismic analysis reported seismic loads on the MHM uplift restraints and EDERER performed corresponding structural calculations to demonstrate structural adequacy of the seismic uplift restraint hardware. The ALSTHOM and EDERER calculations were performed for a parked MHM with the active seismic restraints engaged, resulting in uplift restraint loading only in the vertical direction. In support of development of the CSB Safety Analysis Report (SAR), an evaluation of the MHM seismic response was requested for the case where the active seismic restraints are not engaged. If a seismic event occurs during MHM repositioning operations, a moving contact at a seismic uplift restraint would introduce a friction load on the restraint in the direction of the movement. These potential horizontal friction loads on the uplift restraints were not included in the existing restraint hardware design calculations. One of the purposes of the current evaluation is to address the structural adequacy of the MHM seismic uplift restraints with the addition of the horizontal friction associated with MHM repositioning movements

  14. Sensitivity of reactivity feedback due to core bowing in a metallic-fueled core

    International Nuclear Information System (INIS)

    Nakagawa, Masatoshi; Kawashima, Masatoshi; Endo, Hiroshi; Nishimura, Tomohiro

    1991-01-01

    A sensitivity study has been carried out on negative reactivity feedback caused by core bowing to assess the potential effectiveness of FBR passive safety features in regard to withstanding an anticipated transient without scram (ATWS). In the present study, an analysis has been carried to obtain the best material and geometrical conditions concerning the core restraint system out for several power to flow rates (P/F), up to 2.0 for a 300 MWe metallic-fueled core. From this study, it was clarified that the pad stiffness at an above core loading pads (ACLP) needs to be large enough to ensure negative reactivity feedback against ATWS. It was also clarified that there is an upper limit for the clearances between ducts at ACLP. A new concept, in regard to increasing the absolute value for negative reactivity feedback due to core bowing at ATWS, is proposed and discussed. (author)

  15. Stress and strain patterns, kinematics and deformation mechanisms in a basement-cored anticline: Sheep Mountain Anticline, Wyoming

    Science.gov (United States)

    Amrouch, Khalid; Lacombe, Olivier; Bellahsen, Nicolas; Daniel, Jean-Marc; Callot, Jean-Paul

    2010-02-01

    In order to characterize and compare the stress-strain record prior to, during, and just after folding at the macroscopic and the microscopic scales and to provide insights into stress levels sustained by folded rocks, we investigate the relationship between the stress-strain distribution in folded strata derived from fractures, striated microfaults, and calcite twins and the development of the Laramide, basement-cored Sheep Mountain Anticline, Wyoming. Tectonic data were mainly collected in Lower Carboniferous to Permian carbonates and sandstones. In both rock matrix and veins, calcite twins recorded three different tectonic stages: the first stage is a pre-Laramide (Sevier) layer-parallel shortening (LPS) parallel to fold axis, the second one is a Laramide LPS perpendicular to the fold axis, and the third stage corresponds to Laramide late fold tightening with compression also perpendicular to the fold axis. Stress and strain orientations and regimes at the microscale agree with the polyphase stress evolution revealed by populations of fractures and striated microfaults, testifying for the homogeneity of stress record at different scales through time. Calcite twin analysis additionally reveals significant variations of differential stress magnitudes between fold limbs. Our results especially point to an increase of differential stress magnitudes related to Laramide LPS from the backlimb to the forelimb of the fold possibly in relation with motion of an underlying basement thrust fault that likely induced stress concentrations at its upper tip. This result is confirmed by a simple numerical model. Beyond regional implications, this study highlights the potential of calcite twin analyses to yield a representative quantitative picture of stress and strain patterns related to folding.

  16. Comparison of chemical restraint techniques in ostrich (Struthio camelus

    Directory of Open Access Journals (Sweden)

    R Ciboto

    2006-06-01

    Full Text Available Chemical restraint in ostriches is usually required for short-time interventions. Thus, this study established and evaluated intravenous anesthetics formulated from commonly used drugs in order to accomplish total restraint on this species and allow painful procedures to be performed. Thirty male and female ostriches weighing from 40 to 90 kg were randomly distributed into five groups. Animals in Groups I, II and III were given acepromazine (0.25 mg/kg i.m. and those in Groups IV and V were given xylazine (1.0 mg/kg i.m.. The following drugs were administered intravenously 15 to 20 min later: Group I - propofol (4.0 mg/kg, Groups II and IV - ketamine (5.0 mg/kg and diazepam (0.25 mg/kg, Groups III and V - tiletamine-zolazepam (3.0 mg/kg. All protocols have produced satisfactory results regarding total containment, muscular relaxation and maintenance of the evaluated parameters within a normal range.

  17. Wheelchair tiedown and occupant restraint practices in paratransit vehicles.

    Directory of Open Access Journals (Sweden)

    Karen Frost

    Full Text Available The purpose of this study was to characterize wheelchair tiedown and occupant restraint system (WTORS usage in paratransit vehicles based on observations of wheelchair and scooter (wheeled mobility devices, collectively, "WhMD" passenger trips. A retrospective review of on-board video monitoring recordings of WhMD trips was conducted. Four hundred seventy-five video recordings were collected for review and analysis. The use of all four tiedowns to secure the WhMD was observed more frequently for power WhMDs (82% and manual WhMDs (80% compared to scooters (39%, and this difference was significant (p< 0.01. Nonuse or misuse of the occupant restraint system occurred during 88% of WhMD trips, and was most frequently due to vehicle operator neglect in applying the shoulder belt. Despite the absence of incidents or injuries in this study, misuse and nonuse of WTORS potentially place WhMD seated passengers at higher risk of injury during transit. These findings support the need for improved vehicle operator training and passenger education on the proper use of WTORS and development of WTORS with improved usability and/or alternative technologies that can be automated or used independently.

  18. 28 CFR 552.26 - Medical attention in use of force and application of restraints incidents.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Medical attention in use of force and application of restraints incidents. 552.26 Section 552.26 Judicial Administration BUREAU OF PRISONS... § 552.26 Medical attention in use of force and application of restraints incidents. (a) In immediate use...

  19. Clinical decision making on the use of physical restraint in intensive care units

    Directory of Open Access Journals (Sweden)

    Xinqian Li

    2014-12-01

    Full Text Available Physical restraint is a common nursing intervention in intensive care units and nurses often use it to ensure patients' safety and to prevent unexpected accidents. However, existing literature indicated that the use of physical restraint is a complex one because of inadequate rationales, the negative physical and emotional effects on patients, but the lack of perceived alternatives. This paper is aimed to interpret the clinical decision-making theories related to the use of physical restraint in intensive care units in order to facilitate our understanding on the use of physical restraint and to evaluate the quality of decisions made by nurses. By reviewing the literature, intuition and heuristics are the main decision-making strategies related to the use of physical restraint in intensive care units because the rapid and reflexive nature of intuition and heuristics allow nurses to have a rapid response to urgent and emergent cases. However, it is problematic if nurses simply count their decision-making on experience rather than incorporate research evidence into clinical practice because of inadequate evidence to support the use of physical restraint. Besides that, such a rapid response may lead nurses to make decisions without adequate assessment and thinking and therefore biases and errors may be generated. Therefore, despite the importance of intuition and heuristics in decision-making in acute settings on the use of physical restraint, it is recommended that nurses should incorporate research evidence with their experience to make decisions and adequate assessment before implementing physical restraint is also necessary.

  20. [Vision on and use of physical restraints and 'smart technology' in nursing homes in Flanders].

    Science.gov (United States)

    Carlassara, V; Lampo, E; Degryse, B; Van Audenhove, C; Spruytte, N

    2017-04-01

    The STAFF-project investigates in what way 'smart technology' can offer an alternative for physical restraints in nursing homes. A survey is realized aimed at gaining more insight into the vision on and the use of physical restraints and 'smart technology'. Two partly overlapping structured questionnaires were developed and sent to nursing home staff in Flanders (Belgium). One hundred fifty six administrators (managers or assistant-managers) and 238 caregiving staff (nurses, nursing aids, paramedical staff and other) completed the online questionnaire. In general there is a low acceptability of physical restraint use, however, a more nuanced picture of acceptability is present depending on the specific motivation for using physical restraints and on the specific means of physical restraints. About half of the administrators say they use smart technology in the nursing home. The two main reasons for not applying (yet) smart technology are 'too high price for smart technology' and 'inadequate infrastructure of the nursing home'. All respondents underscore the importance of multiple strategies to diminish the use of physical restraints in nursing homes. Physical restraint use is a complex theme and needs a nuanced analysis and management. This study shows that there is still room for improvement in diminishing the use of physical restraints and that nursing homes in Flanders are open to use smart technology.

  1. Growth and Predictors of Growth Restraint in Moderately Preterm Children Aged 0 to 4 Years

    NARCIS (Netherlands)

    Bocca-Tjeertes, I.F.; Kerstjens, J.M.; Reijneveld, S.A.; de Winter, A.F.; Bos, A.F.

    2011-01-01

    OBJECTIVE: To describe growth in moderately preterm-born children, determine the prevalence of growth restraint at the age of 4, and identify predictors of growth restraint. We hypothesized that growth in moderately preterm-born children differs from growth in term-born children and that growth

  2. 76 FR 55825 - Federal Motor Vehicle Safety Standards, Child Restraint Systems

    Science.gov (United States)

    2011-09-09

    ... [Docket No. NHTSA-2011-0139] RIN 2127-AJ44 Federal Motor Vehicle Safety Standards, Child Restraint Systems..., amends a provision in Federal Motor Vehicle Safety Standard No. 213, ``Child restraint systems,'' that... provision: When a motor vehicle safety standard is in effect under this chapter, a State or a political...

  3. Drilling, Coring and Sampling Using Piezoelectric Actuated Mechanisms: From the USDC to a Piezo-Rotary-Hammer Drill

    Science.gov (United States)

    Bar-Cohen, Yoseph; Sherrit, Stewart; Badescu, Mircea; Bao, Xiaoqi

    2012-01-01

    NASA exploration missions are increasingly including sampling tasks but with the growth in engineering experience (particularly, Phoenix Scout and MSL) it is now very much recognized that planetary drilling poses many challenges. The difficulties grow significantly with the hardness of sampled material, the depth of drilling and the harshness of the environmental conditions. To address the requirements for samplers that could be operated at the conditions of the various bodies in the solar system, a number of piezoelectric actuated drills and corers were developed by the Advanced Technologies Group of JPL. The basic configuration that was conceived in 1998 is known as the Ultrasonic/Sonic Driller/Corer (USDC), and it operates as a percussive mechanism. This drill requires as low preload as 10N (important for operation at low gravity) allowing to operate with as low-mass device as 400g, use an average power as low as 2- 3W and drill rocks as hard as basalt. A key feature of this drilling mechanism is the use of a free-mass to convert the ultrasonic vibrations generated by piezoelectric stack to sonic impacts on the bit. Using the versatile capabilities f the USDC led to the development of many configurations and device sizes. Significant improvement of the penetration rate was achieved by augmenting the hammering action by rotation and use of a fluted bit to remove cuttings. To reach meters deep in ice a wireline drill was developed called the Ultrasonic/Sonic Gopher and it was demonstrated in 2005 to penetrate about 2-m deep at Antarctica. Jointly with Honeybee Robotics, this mechanism is currently being modified to incorporate rotation and inchworm operation forming Auto-Gopher to reach meters deep in rocks. To take advantage of the ability of piezoelectric actuators to operate over a wide temperatures range, piezoelectric actuated drills were developed and demonstrated to operate at as cold as -200oC and as hot as 500oC. In this paper, the developed mechanisms

  4. Effect of chronic restraint stress on inhibitory gating in the auditory cortex of rats.

    Science.gov (United States)

    Ma, Lanlan; Li, Wai; Li, Sibin; Wang, Xuejiao; Qin, Ling

    2017-05-01

    A fundamental adaptive mechanism of auditory function is inhibitory gating (IG), which refers to the attenuation of neural responses to repeated sound stimuli. IG is drastically impaired in individuals with emotional and cognitive impairments (i.e. posttraumatic stress disorder). The objective of this study was to test whether chronic stress impairs the IG of the auditory cortex (AC). We used the standard two-tone stimulus paradigm and examined the parametric qualities of IG in the AC of rats by recording the electrophysiological signals of a single-unit and local field potential (LFP) simultaneously. The main results of this study were that most of the AC neurons showed a weaker response to the second tone than to the first tone, reflecting an IG of the repeated input. A fast negative wave of LFP showed consistent IG across the sampled AC sites, whereas a slow positive wave of LFP had less IG effect. IG was diminished following chronic restraint stress at both, the single-unit and LFP level, due to the increase in response to the second tone. This study provided new evidence that chronic stress disrupts the physiological function of the AC. Lay Summary The effects of chronic stress on IG were investigated by recording both, single-unit spike and LFP activities, in the AC of rats. In normal rats, most of the single-unit and N25 LFP activities in the AC showed an IG effect. IG was diminished following chronic restraint stress at both, the single-unit and LFP level.

  5. Novel elastomeric fibrous networks produced from poly(xylitol sebacate)2:5 by core/shell electrospinning: fabrication and mechanical properties.

    Science.gov (United States)

    Li, Yuan; Thouas, George A; Chen, Qizhi

    2014-12-01

    Fabrication of nonlinear elastic materials that resemble biological tissues remains a challenge in biomaterials research. Here, a new fabrication protocol to produce elastomeric fibrous scaffolds was established, using the core/shell electrospinning technique. A prepolymer of poly(xylitol sebacate) with a 2:5mol ratio of xylitol:sebacic acid (PXS2:5) was first formulated, then co-electrospun with polyvinyl alcohol (PVA - 95,000Mw). After cross-linking of core polymer PXS2:5, the PVA shells were rinsed off in water, leaving a porous elastomeric network of PXS2:5 fibres. Under aqueous conditions, the PXS2:5 fibrous scaffolds exhibited stable, nonlinear J-shaped stress-strain curves, with large average rupture elongation (76%) and Young׳s modulus (~1.0MPa), which were in the range of muscle tissue. Rupture elongation of PXS2:5 was also much higher when electrospun, compared to 2D solid sheets (45%). In direct contact with cell monolayers under physiological conditions, PXS2:5 scaffolds were as biocompatible as those made of poly-l-lactic acid (PLLA), with improvements over culture medium alone. In conclusion, the newly developed porous PXS2:5 scaffolds show tissue-like mechanical properties and excellent biocompatibility, making them very promising for bioengineering of soft tissues and organs. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

  6. Enhancement of the Mechanical Properties and Dimensional Stability of Oil Palm Empty Fruit Bunch-Kenaf Core and Oil Palm Mesocarp-Kenaf Core Hybrid Fiber-Reinforced Poly(lactic acid Biocomposites by Borax Decahydrate Modification of Fibers

    Directory of Open Access Journals (Sweden)

    Abubakar Umar Birnin-Yauri

    2016-04-01

    Full Text Available The surfaces of kenaf core fiber (KCF, oil palm empty fruit bunch fiber (EFBF, and oil palm mesocarp fiber (OPMF, were chemically modified using 5 wt.% aqueous sodium tetraborate decahydrate (borax solution to enhance their hybrid fiber interface bonding with a polylactic acid (PLA matrix. The untreated fibers (KCF, EFBF, and OPMF and treated fibers (BXKCF, BXEFBF, and BXOPMF, were examined using chemical analysis, Fourier transform infrared (FTIR spectroscopy, and scanning electron microscopy (SEM. The treatment caused minimal removal of lignin and significant elimination of hemicellulose and waxy substances. The treated and untreated KCF (5%, as a secondary fiber, was randomly mixed, respectively, with treated and untreated EFBF and OPMF (55%, melt-blended with PLA (40%, and subsequently compression-molded to form hybrid fiber-PLA biocomposites. The resulting composite is aimed to exhibit improvements in its mechanical properties and dimensional stability. The optimum results for tensile and flexural properties, as well as water uptake and thickness swelling, were observed for the borax-treated fibers in comparison with the untreated fibers. The BXEFBF-BXKCF-PLA biocomposites exhibited the best results. This work demonstrated that aqueous borax modification of natural fibers could offer a possible option to the most common mercerization method.

  7. Torsional Restraint Problem of Steel Cold-Formed Beams Restrained By Planar Members

    Science.gov (United States)

    Balázs, Ivan; Melcher, Jindřich; Pešek, Ondřej

    2017-10-01

    The effect of continuous or discrete lateral and torsional restraints of metal thinwalled members along their spans can positively influence their buckling resistance and thus contribute to more economical structural design. The prevention of displacement and rotation of the cross-section results in stabilization of the member. The restraints can practically be provided e.g. by planar members of cladding supported by metal members (purlins, girts). The rate of stabilization of a member can be quantified using values of shear and rotational stiffness provided by the adjacent planar members. While the lateral restraint effected by certain shear stiffness can be often considered as sufficient, the complete torsional restraint can be safely considered in some practical cases only. Otherwise the values of the appropriate rotational stiffness provided by adjacent planar members may not be satisfactory to ensure full torsional restraint and only incomplete restraint is available. Its verification should be performed using theoretical and experimental analyses. The paper focuses on problem of steel thin-walled coldformed beams stabilized by planar members and investigates the effect of the magnitude of the rotational stiffness provided by the planar members on the resistance of the steel members. Cold-formed steel beams supporting planar members of cladding are considered. Full lateral restraint and incomplete torsional restraint are assumed. Numerical analyses performed using a finite element method software indicate considerable influence of the torsional restraint on the buckling resistance of a steel thin-walled member. Utilization of the torsional restraint in the frame of sizing of a stabilized beam can result in more efficient structural design. The paper quantifies this effect for some selected cases and summarizes results of numerical analysis.

  8. Safety characteristics of the US advanced liquid metal reactor core

    International Nuclear Information System (INIS)

    Magee, P.M.; Dubberley, A.E.; Gyorey, G.L.; Lipps, A.J.; Wu, T.

    1991-01-01

    The U.S. Advanced Liquid Metal Reactor (ALMR) design employs innovative, passive features to provide an unprecedented level of public safety and the ability to demonstrate this safety to the public. The key features employed in the core design to produce the desired passive safety characteristics are: a small core with a tight restraint system, the use of metallic U-Pu-Zr fuel, control rod withdrawal limiters, and gas expansion modules. In addition, the reactor vessel and closure are designed to have the capability to withstand, with large margins, the maximum possible core disruptive accident without breach and radiological release. (author)

  9. Dynamic Mechanical Properties and Fracture Surface Morphologies of Core-Shell Rubber (CSR) Toughened Epoxy at Liquid Nitrogen (Ln2) Temperatures

    Science.gov (United States)

    Wang, J.; Magee, D.; Schneider, J. A.

    2009-01-01

    The dynamic mechanical properties and fracture surface morphologies were evaluated for a commercial epoxy resin toughened with two types of core-shell rubber (CSR) toughening agents (Kane Ace(Registered TradeMark) MX130 and MX960). The impact resistance (R) was evaluated by the resulting breaking energy measured in Charpy impact tests conducted on an instrumented drop tower. The resulting fracture surface morphologies were examined using Scanning Electron Microscopy (SEM). Fractographic observations of the CSR toughened epoxy tested at ambient temperature, showed a fracture as characterized by slender dendrite textures with large voids. The increasing number of dendrites and decreasing size of scale-like texture with more CSR particles corresponded with increased R. As the temperature decreased to Liquid Nitrogen (LN 2), the fracture surfaces showed a fracture characterized by a rough, torn texture containing many river markings and deep furrows.

  10. Mental health inpatients' and staff members' suggestions for reducing physical restraint: A qualitative study.

    Science.gov (United States)

    Wilson, C; Rouse, L; Rae, S; Kar Ray, M

    2018-04-01

    WHAT IS KNOWN ON THE SUBJECT?: Restraint has negative psychological, physical and relational consequences for mental health patients and staff. Restraint reduction interventions have been developed (e.g., "Safewards"). Limited qualitative research has explored suggestions on how to reduce physical restraint (and feasibility issues with implementing interventions) from those directly involved. WHAT DOES THIS PAPER ADD TO EXISTING KNOWLEDGE?: This paper explores mental health patients' and staff members' suggestions for reducing physical restraint, whilst addressing barriers to implementing these. Findings centred on four themes: improving communication and relationships; staffing factors; environment and space; and activities and distraction. Not all suggestions are addressed by currently available interventions. Barriers to implementation were identified, centring on a lack of time and/or resources; with the provision of more time for staff to spend with patients and implement interventions seen as essential to reducing physical restraint. WHAT ARE THE IMPLICATIONS FOR PRACTICE?: Improving communication and relationships between staff/patients, making staffing-related changes, improving ward environments and providing patient activities are central to restraint reduction in mental healthcare. Fundamental issues related to understaffing, high staff turnover, and lack of time and resources need addressing in order for suggestions to be successfully implemented. Introduction Physical restraint has negative consequences for all involved, and international calls for its reduction have emerged. Some restraint reduction interventions have been developed, but limited qualitative research explores suggestions on how to reduce physical restraint (and feasibility issues with implementation) from those directly involved. Aims To explore mental health patients' and staff members' suggestions for reducing physical restraint. Methods Interviews were conducted with 13 inpatients

  11. Do organisational constraints explain the use of restraint? A comparative ethnographic study from three nursing homes in Norway.

    Science.gov (United States)

    Øye, Christine; Jacobsen, Frode Fadnes; Mekki, Tone Elin

    2017-07-01

    To investigate (1) what kind of restraint is used in three nursing homes in Norway and (2) how staff use restraint under what organisational conditions. Restraint use in residents living with dementia in nursing homes is controversial, and at odds with fundamental human rights. Restraint is a matter of hindering residents' free movement and will by applying either interactional, physical, medical, surveillance or environmental restraint. Previous research has identified use of restraint related to individual resident characteristics such as agitation, aggressiveness and wandering. This model is embedded in an overall mixed-method education intervention design study called Modelling and evaluating evidence-based continuing education program in dementia care (MEDCED), applying ethnography postintervention to examine the use of restraint in 24 nursing homes in Norway. Based on restraint diversity measured in the trial, ethnographic investigation was carried out in three different nursing homes in Norway over a 10-month period to examine restraint use in relation to organisational constraints. Several forms of restraint were observed; among them, interactional restraint was used most frequently. We identified that use of restraint relates to the characteristics of individual residents, such as agitation, aggressiveness and wandering. However, restraint use should also be explained in relation to organisational conditions such as resident mix, staff culture and available human resources. A fluctuating and dynamic interplay between different individual and contextual factors determines whether restraint is used - or not in particular situations with residents living with dementia. Educational initiatives targeting staff to reduce restraint must be sensitive towards fluctuating organisational constraints. © 2016 John Wiley & Sons Ltd.

  12. Social factors modulate restraint stress induced hyperthermia in mice.

    Science.gov (United States)

    Watanabe, Shigeru

    2015-10-22

    Stress-induced hyperthermia (SIH) was examined in three different social conditions in mice by thermographic measurement of the body surface temperature. Placing animals in cylindrical holders induced restraint stress. I examined the effect of the social factors in SIH using the thermograph (body surface temperature). Mice restrained in the holders alone showed SIH. Mice restrained in the holders at the same time as other similarly restrained cage mates (social equality condition) showed less hyperthermia. Interestingly, restrained mice with free moving cage mates (social inequality condition) showed the highest hyperthermia. These results are consistent with a previous experiment measuring the memory-enhancing effects of stress and the stress-induced elevation of corticosterone, and suggest that social inequality enhances stress. Copyright © 2015 Elsevier B.V. All rights reserved.

  13. The application of viscous dampers as pipe restraints

    International Nuclear Information System (INIS)

    Keowen, R.S.; Hueffmann, G.; Mays, B.; Rencher, D.

    1993-01-01

    Dynamic loading of power generation piping systems may result in nonpermissable deflections and stresses. Fatigue failure translate to increased maintenance costs and possible lost revenue. Undesirable loading can occur due to external events such as earthquakes and internal events such as water and steam hammer, two-phase flow and cavitation. Sway braces and snubbers have been employed to reduce the negative effects of piping motion in emergency cases, however, repetitive loading due to internal events has caused premature wear and failure. Visco elastic dampers, however, have proven to be piping response due to slugging, steam hammer and other repetitive loads. Functional and modeling aspects of visco elastic dampers are discussed, experimental evidence of their effectiveness in a steam hammer application is presented and examples of primary coolant loop restraint applications are illustrated

  14. Wheelchair tiedown and occupant restraint practices in paratransit vehicles.

    Science.gov (United States)

    Frost, Karen; Bertocci, Gina; Smalley, Craig

    2018-01-01

    The purpose of this study was to characterize wheelchair tiedown and occupant restraint system (WTORS) usage in paratransit vehicles based on observations of wheelchair and scooter (wheeled mobility devices, collectively, "WhMD") passenger trips. A retrospective review of on-board video monitoring recordings of WhMD trips was conducted. Four hundred seventy-five video recordings were collected for review and analysis. The use of all four tiedowns to secure the WhMD was observed more frequently for power WhMDs (82%) and manual WhMDs (80%) compared to scooters (39%), and this difference was significant (pinjuries in this study, misuse and nonuse of WTORS potentially place WhMD seated passengers at higher risk of injury during transit. These findings support the need for improved vehicle operator training and passenger education on the proper use of WTORS and development of WTORS with improved usability and/or alternative technologies that can be automated or used independently.

  15. Can child restraint product information developed using consumer testing sustain correct use 6 months after child restraint purchase? Study protocol for a cluster randomised controlled trial.

    Science.gov (United States)

    Brown, Julie; Elkington, Jane; Hall, Alexandra; Keay, Lisa; Charlton, Judith L; Hunter, Kate; Koppel, Sjaan; Hayen, Andrew; Bilston, Lynne E

    2018-03-07

    With long-standing and widespread high rates of errors in child restraint use, there is a need to identify effective methods to address this problem. Information supplied with products at the point of sale may be a potentially efficient delivery point for such a countermeasure. The aim of this study is to establish whether product materials developed using a consumer-driven approach reduce errors in restraint use among purchasers of new child restraint systems. A cluster randomised controlled trial (cRCT) will be conducted. Retail stores (n=22) in the greater Sydney area will be randomised into intervention sites (n=11) and control sites (n=11), stratified by geographical and socioeconomic indicators. Participants (n=836) will enter the study on purchase of a restraint. Outcome measures are errors in installation of the restraint as observed by a trained researcher during a 6-month follow-up home assessment, and adjustment checks made by the parent when the child is placed into the restraint (observed using naturalistic methods). Process evaluation measures will also be collected during the home visit. An intention-to-treat approach will be used for all analyses. Correct use and adjustment checks made by the parent will be compared between control and intervention groups using a logistic regression model. The number of installation errors between groups will be compared using Poisson regression. This cRCT will determine the effectiveness of targeted, consumer-driven information on actual error rates in use of restraints. More broadly, it may provide a best practice model for developing safety product information. ACTRN12617001252303p; Pre-results. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  16. A novel ventricular restraint device (ASD) repetitively deliver Salvia miltiorrhiza to epicardium have good curative effects in heart failure management.

    Science.gov (United States)

    Naveed, Muhammad; Wenhua, Li; Gang, Wang; Mohammad, Imran Shair; Abbas, Muhammad; Liao, Xiaoqian; Yang, Mengqi; Zhang, Li; Liu, Xiaolin; Qi, Xiaoming; Chen, Yineng; Jiadi, Lv; Ye, Linlan; Zhijie, Wang; Ding, Chen Ding; Feng, Yu; Xiaohui, Zhou

    2017-11-01

    A novel ventricular restraint is the non-transplant surgical option for the management of an end-stage dilated heart failure (HF). To expand the therapeutic techniques we design a novel ventricular restraint device (ASD) which has the ability to deliver a therapeutic drug directly to the heart. We deliver a Traditional Chinese Medicine (TCM) Salvia miltiorrhiza (Danshen Zhusheye) through active hydraulic ventricular support drug delivery system (ASD) and we hypothesize that it will show better results in HF management than the restraint device and drug alone. SD rats were selected and divided into five groups (n=6), Normal, HF, HF+SM (IV), HF+ASD, HF+ASD+SM groups respectively. Post myocardial infarction (MI), electrocardiography (ECG) showed abnormal heart function in all groups and HF+ASD+SM group showed a significant therapeutic improvement with respect to other treatment HF, HF+ASD, and HF+SM (IV) groups on day 30. The mechanical functions of the heart such as heart rate, LVEDP, and LVSP were brought to normal when treated with ASD+SM and show significant (P valueASD+SM group animals compared with other treatment groups. Masson's Trichrome staining was used to study histopathology of cardiac myocytes and quantification of fibrosis was assessed. The large blue fibrotic area was observed in HF, HF+ASD, and HF+SM (IV) groups while HF+ASD+SM showed negligible fibrotic myocyte at the end of study period (30days). This study proves that novel ASD device augments the therapeutic effect of the drug and delivers Salvia miltiorrhiza to the cardiomyocytes significantly as well as provides additional support to the dilated ventricle by the heart failure. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  17. Effect of head restraint backset on head-neck kinematics in whiplash.

    Science.gov (United States)

    Stemper, Brian D; Yoganandan, Narayan; Pintar, Frank A

    2006-03-01

    Although head restraints were introduced in the 1960s as a countermeasure for whiplash, their limited effectiveness has been attributed to incorrect positioning. The effect of backset on cervical segmental angulations, which were previously correlated with spinal injury, has not been delineated. Therefore, the practical restraint position to minimize injury remains unclear. A parametric study of increasing head restraint backset between 0 and 140mm was conducted using a comprehensively validated computational model. Head retraction values increased with increasing backset, reaching a maximum value of 53.5mm for backsets greater than 60mm. Segmental angulation magnitudes, greatest at levels C5-C6 and C6-C7, reached maximum values during the retraction phase and increased with increasing backset. Results were compared to a previously published head restraint rating system, wherein lower cervical extension magnitudes from this study exceeded mean physiologic limits for restraint positions rated good, acceptable, marginal, and poor. As head restraint contact was the limiting factor in head retraction and segmental angulations, the present study indicates that minimizing whiplash injury may be accomplished by limiting head restraint backset to less than 60mm either passively or actively after impact.

  18. Exogenous agmatine has neuroprotective effects against restraint-induced structural changes in the rat brain

    Science.gov (United States)

    Zhu, Meng-Yang; Wang, Wei-Ping; Cai, Zheng-Wei; Regunathan, Soundar; Ordway, Gregory

    2009-01-01

    Agmatine is an endogenous amine derived from decarboxylation of arginine catalysed by arginine decarboxylase. Agmatine is considered a novel neuromodulator and possesses neuroprotective properties in the central nervous system. The present study examined whether agmatine has neuroprotective effects against repeated restraint stress-induced morphological changes in rat medial prefrontal cortex and hippocampus. Sprague-Dawley rats were subjected to 6 h of restraint stress daily for 21 days. Immunohistochemical staining with β-tubulin III showed that repeated restraint stress caused marked morphological alterations in the medial prefrontal cortex and hippocampus. Stress-induced alterations were prevented by simultaneous treatment with agmatine (50 mg/kg/day, i.p.). Interestingly, endogenous agmatine levels, as measured by high-performance liquid chromatography, in the prefrontal cortex and hippocampus as well as in the striatum and hypothalamus of repeated restraint rats were significantly reduced as compared with the controls. Reduced endogenous agmatine levels in repeated restraint animals were accompanied by a significant increase of arginine decarboxylase protein levels in the same regions. Moreover, administration of exogenous agmatine to restrained rats abolished increases of arginine decarboxylase protein levels. Taken together, these results demonstrate that exogenously administered agmatine has neuroprotective effects against repeated restraint-induced structural changes in the medial prefrontal cortex and hippocampus. These findings indicate that stress-induced reductions in endogenous agmatine levels in the rat brain may play a permissive role in neuronal pathology induced by repeated restraint stress. PMID:18364017

  19. A daily diary study of perceived social isolation, dietary restraint, and negative affect in binge eating.

    Science.gov (United States)

    Mason, Tyler B; Heron, Kristin E; Braitman, Abby L; Lewis, Robin J

    2016-02-01

    Negative affect and dietary restraint are key predictors of binge eating, yet less is known about the impact of social factors on binge eating. The study sought to replicate and extend research on the relationships between negative affect, dietary restraint, perceived social isolation and binge eating using a daily diary methodology. College women (N = 54) completed measures of dietary restraint, negative affect, perceived social isolation, and binge eating daily for 14 days. Participants completed the measures nightly each day. A series of generalized estimating equations showed that dietary restraint was associated with less binge eating while controlling for negative affect and for perceived social isolation separately. Negative affect and perceived social isolation were associated with greater binge eating while controlling for restraint in separate analyses, but only perceived social isolation was significant when modeled simultaneously. All two-way interactions between negative affect, dietary restraint, and perceived social isolation predicting binge eating were nonsignificant. This study furthers our understanding of predictors of binge eating in a nonclinical sample. Specifically, these data suggest perceived social isolation, negative affect, and dietary restraint are important variables associated with binge eating in daily life and warrant further research. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. [Therapeutic restraint management in Intensive Care Units: Phenomenological approach to nursing reality].

    Science.gov (United States)

    Acevedo-Nuevo, M; González-Gil, M T; Solís-Muñoz, M; Láiz-Díez, N; Toraño-Olivera, M J; Carrasco-Rodríguez-Rey, L F; García-González, S; Velasco-Sanz, T R; Martínez-Álvarez, A; Martin-Rivera, B E

    2016-01-01

    To identify nursing experience on physical restraint management in Critical Care Units. To analyse similarities and differences in nursing experience on physical restraint management according to the clinical context that they are involved in. A multicentre phenomenological study was carried out including 14 Critical Care Units in Madrid, classified according to physical restraint use: Common/systematic use, lacking/personalised use, and mixed use. Five focus groups (23 participants were selected following purposeful sampling) were convened, concluding in data saturation. Data analysis was focused on thematic content analysis following Colaizzi's method. Six main themes: Physical restraint meaning in Critical Care Units, safety (self-retreat vital devices), contribution factors, feelings, alternatives, and pending issues. Although some themes are common to the 3 Critical Care Unit types, discourse differences are found as regards to indication, feelings, systematic use of pain and sedation measurement tools. In order to achieve real physical restraint reduction in Critical Care Units, it is necessary to have a deep understanding of restraints use in the specific clinical context. As self-retreat vital devices emerge as central concept, some interventions proposed in other settings could not be effective, requiring alternatives for critical care patients. Discourse variations laid out in the different Critical Care Unit types could highlight key items that determine the use and different attitudes towards physical restraint. Copyright © 2015 Elsevier España, S.L.U. y SEEIUC. All rights reserved.

  1. Minimizing Restraint and Seclusion in Schools: A Response to Beaudoin and Moore.

    Science.gov (United States)

    Walker, Virginia L; Pinkelman, Sarah E

    2018-06-01

    Increasing efforts have been made in the field of special education to identify positive, evidence-based practices (EBPs) to meet the needs of students who engage in problem behavior, with a major goal being to eliminate or limit the use of reactive measures such as restraint and seclusion ( Snell & Walker, 2014 ). Various stakeholders, including families and self-advocates, have voiced concerns about the dangers of restraint and seclusion and the lack of protection afforded to students who engage in severe problem behavior. In the previous article in this issue of Intellectual and Developmental Disabilities, Beaudoin and Moore (2018) echo these concerns in their account of a family's experience with restraint as told from the perspective of a father whose son was subjected to restraint, resulting in a number of adverse short- and long-term consequences that affected the entire family. In response to Beaudoin and Moore, we provide readers with a brief review of the current status of restraint and seclusion in school settings and evidence-based strategies that can be used to address severe problem behavior and reduce the need for restraint and seclusion. For readers interested in exploring restraint and seclusion in greater depth, we suggest recent work by Trader and colleagues (2017) . We also have outlined guidelines for behavior support planning that should be considered by various stakeholders as educators work toward establishing safe and supportive school environments that address a wide range of student behavioral needs.

  2. SUPERENERGY-2: a multiassembly, steady-state computer code for LMFBR core thermal-hydraulic analysis

    Energy Technology Data Exchange (ETDEWEB)

    Basehore, K.L.; Todreas, N.E.

    1980-08-01

    Core thermal-hydraulic design and performance analyses for Liquid Metal Fast Breeder Reactors (LMFBRs) require repeated detailed multiassembly calculations to determine radial temperature profiles and subchannel outlet temperatures for various core configurations and subassembly structural analyses. At steady-state, detailed core-wide temperature profiles are required for core restraint calculations and subassembly structural analysis. In addition, sodium outlet temperatures are routinely needed for each reactor operating cycle. The SUPERENERGY-2 thermal-hydraulic code was designed specifically to meet these designer needs. It is applicable only to steady-state, forced-convection flow in LMFBR core geometries.

  3. SUPERENERGY-2: a multiassembly, steady-state computer code for LMFBR core thermal-hydraulic analysis

    International Nuclear Information System (INIS)

    Basehore, K.L.; Todreas, N.E.

    1980-08-01

    Core thermal-hydraulic design and performance analyses for Liquid Metal Fast Breeder Reactors (LMFBRs) require repeated detailed multiassembly calculations to determine radial temperature profiles and subchannel outlet temperatures for various core configurations and subassembly structural analyses. At steady-state, detailed core-wide temperature profiles are required for core restraint calculations and subassembly structural analysis. In addition, sodium outlet temperatures are routinely needed for each reactor operating cycle. The SUPERENERGY-2 thermal-hydraulic code was designed specifically to meet these designer needs. It is applicable only to steady-state, forced-convection flow in LMFBR core geometries

  4. CLASSIFICATION OF RESTRAINTS IN THE OPTIMIZATION PROBLEM OF A COLD-FORMED PROFILE

    Directory of Open Access Journals (Sweden)

    Agnieszka Łukowicz

    2015-11-01

    Full Text Available This work describes the restraints in the optimization problem. This is an important and complicated issue because it requires taking into account a vast range of information related to the design and production. In order to describe the relations of a specific optimization problem, it is essential to adopt appropriate criteria and to collect information on all kinds of restraints, i.e. boundary conditions. The following paper verifies the various restraints and defines three subsets: design assumptions, technological limitations and standard conditions. The provided classification was made with reference to the analysis of the construction applicability of the newly patented cold-formed profile.

  5. [Physical and pharmacological restraints in geriatric and gerontology services and centers].

    Science.gov (United States)

    Ramos Cordero, Primitivo; López Trigo, José Antonio; Maíllo Pedraz, Herminio; Paz Rubio, José María

    2015-01-01

    Physical and pharmacological restraints are a controversial issue in the context of geriatric care due to their moral, ethical, social and legal repercussions and, despite this fact, no specific legislation exists at a national level. The use of restraints is being questioned with growing frequency, as there are studies that demonstrate that restraints do not reduce the number of falls or their consequences, but rather can increase them, cause complications, injuries and potentially fatal accidents. Restraints are not always used rationally, despite compromising a fundamental human right, that is, freedom, protected in the Constitution, as well as values and principles, such as dignity and personal self-esteem. There are centers where restraints are applied to more than 50% of patients, and in some cases without the consent of their legal representatives. On some occasions, restraints are used for attaining organizational or environmental objectives, such as complying with tight schedules, and for reducing or avoiding the supervision of patients who walk erratically and, at times, are used indefinitely. Even greater confusion exists with respect to the emerging concept of chemical or pharmacological restraints, since no conceptual framework exists based on scientific evidence, and with sufficient consensus for guiding healthcare workers. In this context, the Sociedad Española de Geriatría y Gerontología (SEGG--Spanish Geriatrics and Gerontology Society), aware of the significance and transcendence of the issue, and in an attempt to preserve and guarantee maximum freedom, dignity and self-esteem, on the one hand, and to ensure the maximum integrity and legal certainty of the persons cared for in geriatric and gerontology services and centers, on the other, decided to create an "Interdisciplinary Committee on Restraints" made up by members from different disciplines and members of SEGG Working Groups or Committees, external health care workers, groups

  6. Dietary restraint partially mediates the relationship between impulsivity and binge eating only in lean individuals: The importance of accounting for body mass in studies of restraint

    Directory of Open Access Journals (Sweden)

    Jaime Ashley Coffino

    2016-10-01

    Full Text Available Binge eating is characteristic of eating and weight-related disorders such as binge eating disorder, bulimia nervosa, and obesity. In light of data that suggests impulsivity is associated with overeating specifically in restrained eaters, this study sought to elucidate the exact nature of the associations between these variables, hypothesizing that the relationship between impulsivity and binge eating is mediated by restrained eating. We further hypothesized that the role of dietary restraint as a mediator would be moderated by body mass index (BMI. Study participants (n = 506, 50.6% female were categorized based on self-reported BMI as under- and normal weight (BMI < 25, 65.8%, n = 333 or overweight and obese (BMI ≥ 25, 34.2%, n = 173 and completed the restrained eating subscale of the Dutch Eating Behavior Questionnaire, the difficulties with impulse control subscale of the Difficulties with Emotion Regulation Scale, and the Binge Eating Scale. Findings provide initial evidence for the hypothesized moderated mediation model, with dietary restraint partially mediating the relationship between impulsivity and binge eating severity only in lean respondents. In respondents with overweight or obesity, impulsivity was significantly correlated with binge eating severity, but dietary restraint was not. Findings inform our conceptualization of dietary restraint as a possible risk factor for binge eating and highlight the importance of accounting for body mass in research on the impact of dietary restraint on eating behaviors.

  7. Design features of selected mechanisms developed for use in Spacelab. [mechanical ground support equipment and environmental control

    Science.gov (United States)

    Inden, W.

    1979-01-01

    Selected mechanisms developed for the Spacelab program are discussed. These include: (1) the roller rail used to install/remove the Spacelab floor loaded with racks carrying experiments; (2) the foot restraint; and (3) the lithium hydroxide used for decontamination.

  8. The effect of restraints type on the generated stresses in gantry crane beam

    Directory of Open Access Journals (Sweden)

    Sowa Leszek

    2018-01-01

    Full Text Available This paper includes an analysis of the mechanical phenomena in the gantry crane beam, because the cranes are currently one of the most common devices for the transporting loads. Designing modern mechanical structures is a complex task that requires the use of appropriate tools. Such a modern tool is the numerical simulation, which uses different numerical methods. One of the best known methods is the finite element method, also used here. Simulations are limited to analysis of the strength of the gantry crane beam that was the loaded of the force load movement along its length. The numerical analysis was made to the gantry crane beam which cross-section was an I-beam and ends were fixed in different ways. As the result of numerical calculations, the stresses and displacements of the structure of gantry were obtained. The influence of the restraints type and changing the loading force position on generate the Huber-Misses stress in the gantry crane beam was estimated. The aim was to ensure that the maximum equivalent stress generated in the gantry crane beam was less than the strength of material, because then the construction is safe.

  9. The Role of MAPK and Dopaminergic Synapse Signaling Pathways in Antidepressant Effect of Electroacupuncture Pretreatment in Chronic Restraint Stress Rats

    Directory of Open Access Journals (Sweden)

    Xinjing Yang

    2017-01-01

    Full Text Available Acupuncture has demonstrated the function in ameliorating depressive-like behaviors via modulating PKA/CREB signaling pathway. To further confirm the antidepressant mechanism of EA on the mitogen-activated protein kinase (MAPK and dopaminergic synapse signaling pathways, 4 target proteins were detected based on our previous iTRAQ analysis. Rats were randomly divided into control group, model group, and electroacupuncture (EA group. Except for the control group, all rats were subjected to 28 days of chronic restraint stress (CRS protocols to induce depression. In the EA group, EA pretreatment at Baihui (GV20 and Yintang (GV29 was performed daily (1 mA, 2 Hz, discontinuous wave, 20 minutes prior to restraint. The antidepressant-like effect of EA was measured by body weight and open-field test. The protein levels of DAT, Th, Mapt, and Prkc in the hippocampus were examined by using Western blot. The results showed EA could ameliorate the depression-like behaviors and regulate the expression levels of Prkc and Mapt in CRS rats. The effect of EA on DAT and Th expression was minimal. These findings implied that EA pretreatment could alleviate depression through modulating MAPK signaling pathway. The role of EA on dopaminergic synapse signaling pathways needs to be further explored.

  10. Applying sensory modulation to mental health inpatient care to reduce seclusion and restraint

    DEFF Research Database (Denmark)

    Andersen, Charlotte; Kolmos, Anne; Andersen, Kjeld

    2017-01-01

    that is associated with reduced rates of seclusion and restraint in mental healthcare, but there is need for more research in this area. AIMS: Using SM to reduce restraint and seclusion in inpatient mental health care. METHODS: The study included two similar psychiatric units where one unit implemented SM and one...... unit served as the control group. In the very beginning of the study, a staff-training program in the use of SM including assessment tools and intervention strategies was established. Data on restraint and forced medicine were sampled post the course of the year of implementation and compared...... with the control group. RESULTS: The use of belts decreased with 38% compared to the control group. The use of forced medication decreased with 46% compared to the control group. Altogether the use of physical restraint and forced medication decreased significantly with 42% (p 

  11. Prehospital chemical restraint of a noncommunicative autistic minor by law enforcement.

    Science.gov (United States)

    Ho, Jeffrey D; Nystrom, Paul C; Calvo, Darryl V; Berris, Marc S; Norlin, Jeffrey F; Clinton, Joseph E

    2012-01-01

    When responders are dealing with an agitated patient in the field, safety for all involved may sometimes only be accomplished with physical or chemical restraints. While experiences using chemical restraint in the prehospital setting are found in the medical literature, the use of this by law enforcement as a first-response restraint has not previously been described. We report a case of successful law enforcement-administered sedation of a noncommunicative, autistic, and violent minor using intramuscular droperidol and diphenhydramine. Although this case has some unique characteristics that allowed chemical restraint to be given by the law enforcement agency, it calls attention to some specific prehospital issues that need to be addressed when dealing with autistic patients with extreme agitation.

  12. Fabrication of a small animal restraint for synchrotron biomedical imaging using a rapid prototyper

    International Nuclear Information System (INIS)

    Zhu Ying; Zhang Honglin; McCrea, Richard; Bewer, Brian; Wiebe, Sheldon; Nichol, Helen; Ryan, Christopher; Wysokinski, Tomasz; Chapman, Dean

    2007-01-01

    Biomedical research at synchrotron facilities may involve imaging live animals that must remain motionless for extended periods of time to obtain quality images. Even breathing movements reduce image quality but on the other hand excessive restraint of animals increases morbidity and mortality. We describe a humane animal restraint designed to eliminate head movements while promoting animal survival. This paper describes how an animal restraint that conforms to the shape of an animal's head was fabricated by a 3D prototyper. The method used to translate medical computed tomography (CT) data to a 3D stereolithography format is described and images of its use at the Canadian Light Source (CLS) are shown. This type of restraint holds great promise in improving image quality and repeatability while reducing stress on experimental animals

  13. Examination of ethical dilemmas experienced by adult intensive care unit nurses in physical restraint practices.

    Science.gov (United States)

    Yönt, Gülendam Hakverdioğlu; Korhan, Esra Akin; Dizer, Berna; Gümüş, Fatma; Koyuncu, Rukiye

    2014-01-01

    Nurses are more likely to face the dilemma of whether to resort to physical restraints or not and have a hard time making that decision. This is a descriptive study. A total of 55 nurses participated in the research. For data collection, a question form developed by researchers to determine perceptions of ethical dilemmas by nurses in the application of physical restraint was used. A descriptive analysis was made by calculating the mean, standard deviation, and maximum and minimum values. The nurses expressed (36.4%) having difficulty in deciding to use physical restraint. Nurses reported that they experience ethical dilemmas mainly in relation to the ethic principles of nonmaleficence, beneficence, and convenience. We have concluded that majority of nurses working in critical care units apply physical restraint to patients, although they are facing ethical dilemmas concerning harm and benefit principles during the application.

  14. National roadside survey of child restraint system use in Belgium.

    Science.gov (United States)

    Mathieu, Roynard; Peter, Silverans; Yvan, Casteels; Philippe, Lesire

    2014-01-01

    In September 2011 the Belgian Road Safety Institute (BRSI) conducted its first roadside survey of child restraint system (CRS) use and misuse. The aim of this study was to obtain population-bases estimates of the prevalence of use and misuse of CRS and to identify predictors of misuse on the basis of observations in real traffic conditions. The survey was conducted on randomly selected sites across the country, stratified across various types of journeys. The principal parameters analysed were: the characteristics of the children and the car drivers, type of journey, types of CRS and types of misuse. The sample consisted of 1461 children (under 135cm) for whom the conditions of restraint were observed in detail and the driver was interviewed. At least 50% of the children were not correctly restrained and 10% were not restrained at all. The most significant factors associated with CRS use were the use of a seatbelt by the driver (31% of unrestrained children for unbelted drivers, compared to 7% for belted drivers - only 32% of correctly restrained children for unbelted drivers compared to 54% for belted drivers), whether the CRS was bought in a specialized shop (only 27% of misuse compared to 45% of misuse for CRS both in supermarkets) and the age of the children. The proportion of correctly restrained children (appropriate without misuse, the bottom category in the figure) has a roughly curvilinear relation with age; decreasing from 75% at age 0 to 24% at age 8 and going back up to 63% at age 10. Although the sample of ISOFIX users was small (n=76), it appears that the ISOFIX system reduced misuse significantly. Most of the drivers were ignorant of their own errors concerning the inappropriateness and/or misuse of the CRS or they were remiss and underestimated the risk. The three main reasons given by the drivers to explain or justify the misuse noticed were: low attention level to safety (inattention, time pressure, and short distance), the child's resistance to

  15. Tests for development of estimation technology of reactor core deformation. Report No.1: fundamental mechanical properties of wrapper tube (test report)

    International Nuclear Information System (INIS)

    Nishiura, Takeo; Shimazaki, Yuji; Horikiri, Morito

    1998-10-01

    Mechanical properties such as local contact compression stiffness, bending stiffness, deformation properties, material properties, and friction properties of a wrapper tube structure were clarified experimentally, which can be used as the basic data for development of estimation technology of reactor core deformation. Contents of the Tests data as follows: (1) Effects of load supporting boundary conditions, whether or not a contact-proof pad is attached, and length of duct, on cross section deformation of wrapper tube were made clear as the local contact compression stiffness characteristics. (2) Bending stiffness does not depend on the difference of load supporting boundary conditions. The property of cross section deformation under bending load was obtained. (3) The deformation modes and the strain distributions were obtained by the deformation tests of wrapper tube. (4) The stress-strain diagrams including plastic range under various strain variation rates were obtained by the material tests at room temperature. (5) The static and the dynamic friction coefficients by various contact angles and the contact loads between contact-proof pads of two wrapper tubes were obtained by friction property tests. (author)

  16. Influence of Kenaf Core Fiber Incorporation on the Mechanical Performance and Dimensional Stability of Oil Palm Fiber Reinforced Poly(lactic acid Hybrid Biocomposites

    Directory of Open Access Journals (Sweden)

    Abubakar Umar Birnin-Yauri

    2016-02-01

    Full Text Available This study demonstrated the reinforcing potential of kenaf core fiber (KCF to complement and sustain oil palm fiber supply chain in the production of natural fiber-thermoplastic biocomposites. The lignin-rich KCF was incorporated into cellulose-rich oil palm empty fruit bunch fiber (EFBF- and oil palm mesocarp fiber (OPMF-poly(lactic acid (PLA composites, aimed at achieving synergism. The hybrid biocomposites developed by melt blending and subsequent compression molding were characterized for possible application as an alternative to medium-density fiberboards. The mechanical properties and dimensional stability of both single fiber- and hybrid fiber-PLA biocomposites were evaluated and compared. The test results showed a synergistic improvement as a consequence of fiber hybridization. Also, the findings suggested the best material performance with the incorporation of 5% KCF into 55% EFBF or OPMF and 40% PLA matrix. The OPMF-KCF-PLA hybrid biocomposites gave better results than the EFBF-KCF-PLA hybrid biocomposites.

  17. Comparative Assessment of Torso and Seat Mounted Restraint Systems using Manikins on the Vertical Deceleration Tower

    Science.gov (United States)

    2017-03-01

    AFRL-RH-WP-TR-2017-0044 Comparative Assessment of Torso and Seat Mounted Restraint Systems using Manikins on the Vertical ...Restraint Systems using Manikins on the Vertical Deceleration Tower 5a. CONTRACT NUMBER FA8650-14-D-6500-0001 5b. GRANT NUMBER 5c. PROGRAM...experimental effort involving a series of +z-axis impact tests was conducted on the 711th Human Performance Wing’s Vertical Deceleration Tower (VDT

  18. How the architect-engineer manages design objectives and restraints for optimizing sodium cooled reactors

    International Nuclear Information System (INIS)

    Roe, K.A.; Roe, K.K.

    1978-01-01

    The design objectives of low capital and operating costs and high reliability are best attained by carefully defining criteria early in the development stage. Throughout the design development, unusual attention to constructibility, reliability and availability requirements, and the early resolution of licensing issues by designated engineering specialists are some of the approaches used to minimize design restraints. Effective management of these design objectives and restraints can assure that, on balance, LMFBR costs can be improved, reliability increased, and maintenance can be effective. (author)

  19. The evolution of the doctrine of restraint of trade in Australia: a law reform perspective

    OpenAIRE

    Cheng, John Wei-Ting

    2017-01-01

    This thesis examines the present state of the common law doctrine of restraint of trade from a law reform perspective. The doctrine was developed in England between the 1600s and mid-1800s and its evolution over the centuries has been a slow and ongoing process. The present state of the doctrine and its application in the Australian jurisdiction presents a challenging set of circumstances due to the difficulties faced by contracting parties when they wish to engage in restraint of trade. ...

  20. Mixed selection. Effects of body images, dietary restraint, and persuasive messages on females' orientations towards chocolate.

    Science.gov (United States)

    Durkin, Kevin; Hendry, Alana; Stritzke, Werner G K

    2013-01-01

    Many women experience ambivalent reactions to chocolate: craving it but also wary of its impact on weight and health. Chocolate advertisements often use thin ideal models and previous research indicates that this exacerbates ambivalence. This experiment compared attitudes to, and consumption of, chocolate following exposure to images containing thin or overweight models together with written messages that were either positive or negative about eating chocolate. Participants (all female) were categorised as either low- or high-restraint. Approach, avoidance and guilt motives towards chocolate were measured and the participants had an opportunity to consume chocolate. Exposure to thin ideal models led to higher approach motives and this effect was most marked among the high restraint participants. Avoidance and guilt scores did not vary as a function of model size or message, but there were clear differences between the restraint groups, with the high restraint participants scoring substantially higher than low restraint participants on both of these measures. When the participants were provided with an opportunity to eat some chocolate, those with high restraint who had been exposed to the thin models consumed the most. Copyright © 2012 Elsevier Ltd. All rights reserved.

  1. Restraint status improves the predictive value of motor vehicle crash criteria for pediatric trauma team activation.

    Science.gov (United States)

    Bozeman, Andrew P; Dassinger, Melvin S; Recicar, John F; Smith, Samuel D; Rettiganti, Mallikarjuna R; Nick, Todd G; Maxson, Robert T

    2012-12-01

    Most trauma centers incorporate mechanistic criteria (MC) into their algorithm for trauma team activation (TTA). We hypothesized that characteristics of the crash are less reliable than restraint status in predicting significant injury and the need for TTA. We identified 271 patients (age, <15 y) admitted with a diagnosis of motor vehicle crash. Mechanistic criteria and restraint status of each patient were recorded. Both MC and MC plus restraint status were evaluated as separate measures for appropriately predicting TTA based on treatment outcomes and injury scores. Improper restraint alone predicted a need for TTA with an odds ratios of 2.69 (P = .002). MC plus improper restraint predicted the need for TTA with an odds ratio of 2.52 (P = .002). In contrast, the odds ratio when using MC alone was 1.65 (P = .16). When the 5 MC were evaluated individually as predictive of TTA, ejection, death of occupant, and intrusion more than 18 inches were statistically significant. Improper restraint is an independent predictor of necessitating TTA in this single-institution study. Copyright © 2012 Elsevier Inc. All rights reserved.

  2. Effects and costs of requiring child-restraint systems for young children traveling on commercial airplanes.

    Science.gov (United States)

    Newman, Thomas B; Johnston, Brian D; Grossman, David C

    2003-10-01

    The US Federal Aviation Administration is planning a new regulation requiring children younger than 2 years to ride in approved child-restraint seats on airplanes. To estimate the annual number of child air crash deaths that might be prevented by the proposed regulation, the threshold proportion of families switching from air to car travel above which the risks of the policy would exceed its benefits, and the cost per death prevented. Risk and economic analyses. Child-restraint seat use could prevent about 0.4 child air crash deaths per year in the United States. Increased deaths as a result of car travel could exceed deaths prevented by restraint seat use if the proportion of families switching from air to car travel exceeded about 5% to 10%. The estimate for this proportion varied with assumptions about trip distance, driver characteristics, and the effectiveness of child-restraint seats but is unlikely to exceed 15%. Assuming no increase in car travel, for each dollar increase in the cost of implementing the regulation per round trip per family, the cost per death prevented would increase by about $6.4 million. Unless space for young children in restraint seats can be provided at low cost to families, with little or no diversion to automobile travel, a policy requiring restraint seat use could cause a net increase in deaths. Even excluding this possibility, the cost of the proposed policy per death prevented is high.

  3. Transformer core

    NARCIS (Netherlands)

    Mehendale, A.; Hagedoorn, Wouter; Lötters, Joost Conrad

    2008-01-01

    A transformer core includes a stack of a plurality of planar core plates of a magnetically permeable material, which plates each consist of a first and a second sub-part that together enclose at least one opening. The sub-parts can be fitted together via contact faces that are located on either side

  4. Transformer core

    NARCIS (Netherlands)

    Mehendale, A.; Hagedoorn, Wouter; Lötters, Joost Conrad

    2010-01-01

    A transformer core includes a stack of a plurality of planar core plates of a magnetically permeable material, which plates each consist of a first and a second sub-part that together enclose at least one opening. The sub-parts can be fitted together via contact faces that are located on either side

  5. Interactive effects of dietary restraint and adiposity on stress-induced eating and the food choice of children.

    Science.gov (United States)

    Roemmich, James N; Lambiase, Maya J; Lobarinas, Christina L; Balantekin, Katherine N

    2011-12-01

    The Individual Differences Model posits that individual differences in physiological and psychological factors explain eating behaviors in response to stress. The purpose was to determine the effects of individual differences in adiposity, dietary restraint and stress reactivity on children's energy intake and food choices. A total of 40 boys and girls, age 8-12 years, with wide ranges of dietary restraint, adiposity, and stress reactivity were measured for total energy intake and choice of energy dense 'comfort' and lower density 'healthy' foods following reading and speech stressor manipulations. When exploring the interaction of dietary restraint and stress reactivity, lower restraint/lower reactivity and lower restraint/higher reactivity were associated with reductions in energy intake (37-62 kcal) and comfort food (33-89 kcal). Higher restraint/lower reactivity was associated with consuming 86 fewer total kcal and 45 fewer kcal of comfort food. Only higher restraint/higher reactivity predicted increased energy intake (104 kcal) and comfort food (131 kcal). The interaction of dietary restraint and percentage body fat revealed that lower restraint/lower adiposity was associated with consuming 123 fewer kcal after being stressed with the entire reduction due to a decrease in comfort food. Lower restraint/higher adiposity was associated with consuming 116 kcal more after being stressed with 70% (81 kcal) of the increase in the form of comfort foods. Higher restraint/lower adiposity and higher restraint/higher adiposity were associated with smaller changes in total energy intake of 22 kcal and 1 kcal; respectively. Both restraint and adiposity moderated the effect of stress on energy intake and food choice. Children with greater adiposity may be at risk for stress-induced eating to contribute to their obesity. Copyright © 2011 Elsevier Ltd. All rights reserved.

  6. Real-World Rib Fracture Patterns in Frontal Crashes in Different Restraint Conditions.

    Science.gov (United States)

    Lee, Ellen L; Craig, Matthew; Scarboro, Mark

    2015-01-01

    The purpose of this study was to use the detailed medical injury information in the Crash Injury Research and Engineering Network (CIREN) to evaluate patterns of rib fractures in real-world crash occupants in both belted and unbelted restraint conditions. Fracture patterns binned into rib regional levels were examined to determine normative trends associated with belt use and other possible contributing factors. Front row adult occupants with Abbreviated Injury Scale (AIS) 3+ rib fractures, in frontal crashes with a deployed frontal airbag, were selected from the CIREN database. The circumferential location of each rib fracture (with respect to the sternum) was documented using a previously published method (Ritchie et al. 2006) and digital computed tomography scans. Fracture patterns for different crash and occupant parameters (restraint use, involved physical component, occupant kinematics, crash principal direction of force, and occupant age) were compared qualitatively and quantitatively. There were 158 belted and 44 unbelted occupants included in this study. For belted occupants, fractures were mainly located near the path of the shoulder belt, with the majority of fractures occurring on the inboard (with respect to the vehicle) side of the thorax. For unbelted occupants, fractures were approximately symmetric and distributed across both sides of the thorax. There were negligible differences in fracture patterns between occupants with frontal (0°) and near side (330° to 350° for drivers; 10° to 30° for passengers) crash principal directions of force but substantial differences between groups when occupant kinematics (and contacts within the vehicle) were considered. Age also affected fracture pattern, with fractures tending to occur more anteriorly in older occupants and more laterally in younger occupants (both belted and unbelted). Results of this study confirmed with real-world data that rib fracture patterns in unbelted occupants were more distributed

  7. Restraint of fatigue crack growth by wedge effects of fine particles

    CERN Document Server

    Takahashi, I; Kotani, N

    2000-01-01

    Presents some experimental results which demonstrate restraint of fatigue crack growth in an Al-Mg alloy by wedge effects of fine particles. Fatigue test specimens were machined from a JIS A5083P-O Al-Mg alloy plate of 5 mm thickness and an EDM starter notch was introduced to each specimen. Three kinds of fine particles were prepared as the materials to be wedged into the fatigue cracks, i.e. magnetic particles and two kinds of alumina particles having different mean particle sizes of 47.3 mu m and 15.2 mu m. Particles of each kind were suspended in an oil to form a paste, which was applied on the specimen surface covering the notch zone prior to the fatigue tests. In order to make some fracture mechanics approaches, in situ observations of fatigue cracks were performed for the two cases using a CCD microscope, with a magnification of *1000. The crack length and the crack opening displacement (COD) at the notch root, delta , were measured. The crack retardation effect continues almost through the entire lifet...

  8. Lactobacillus rhamnosus strain JB-1 reverses restraint stress-induced gut dysmotility.

    Science.gov (United States)

    West, C; Wu, R Y; Wong, A; Stanisz, A M; Yan, R; Min, K K; Pasyk, M; McVey Neufeld, K-A; Karamat, M I; Foster, J A; Bienenstock, J; Forsythe, P; Kunze, W A

    2017-01-01

    Environmental stress affects the gut with dysmotility being a common consequence. Although a variety of microbes or molecules may prevent the dysmotility, none reverse the dysmotility. We have used a 1 hour restraint stress mouse model to test for treatment effects of the neuroactive microbe, L. rhamnosus JB-1 ™ . Motility of fluid-filled ex vivo gut segments in a perfusion organ bath was recorded by video and migrating motor complexes measured using spatiotemporal maps of diameter changes. Stress reduced jejunal and increased colonic propagating contractile cluster velocities and frequencies, while increasing contraction amplitudes for both. Luminal application of 10E8 cfu/mL JB-1 restored motor complex variables to unstressed levels within minutes of application. L. salivarius or Na.acetate had no treatment effects, while Na.butyrate partially reversed stress effects on colonic frequency and amplitude. Na.propionate reversed the stress effects for jejunum and colon except on jejunal amplitude. Our findings demonstrate, for the first time, a potential for certain beneficial microbes as treatment of stress-induced intestinal dysmotility and that the mechanism for restoration of function occurs within the intestine via a rapid drug-like action on the enteric nervous system. © 2016 John Wiley & Sons Ltd.

  9. Core lifter

    Energy Technology Data Exchange (ETDEWEB)

    Pavlov, N G; Edel' man, Ya A

    1981-02-15

    A core lifter is suggested which contains a housing, core-clamping elements installed in the housing depressions in the form of semirings with projections on the outer surface restricting the rotation of the semirings in the housing depressions. In order to improve the strength and reliability of the core lifter, the semirings have a variable transverse section formed from the outside by the surface of the rotation body of the inner arc of the semiring aroung the rotation axis and from the inner a cylindrical surface which is concentric to the outer arc of the semiring. The core-clamping elements made in this manner have the possibility of freely rotating in the housing depressions under their own weight and from contact with the core sample. These semirings do not have weakened sections, have sufficient strength, are inserted into the limited ring section of the housing of the core lifter without reduction in its through opening and this improve the reliability of the core lifter in operation.

  10. Effect of PCMI restraint on bubble size distribution in the rim structure of UO2 fuel

    International Nuclear Information System (INIS)

    Oh, Je-Yong; Koo, Yang-Hyun; Cheon, Jin-Sik; Lee, Byung-Ho; Sohn, Dong-Seong

    2005-01-01

    Generally, the bubble size in the rim structure of UO 2 is not dependent on the fuel burnup and the bubble pressure is higher than that in the equilibrium condition. However it was also observed that if the fuel pellet is not restrained, the size of the bubbles in the rim structure could be larger than that in the restraint condition. Although the wide variety of rim bubble sizes and porosities possibly result from an external restrain effect, the quantitative method to analyze the effect of PCMI restraint on bubble distribution in the rim is not available at the moment. In this paper, a method is developed which can be used to analyze the effect of PCMI restraint on the bubble distribution in the rim structure of UO 2 fuel based on the data in the literatures. The total number of Xe atoms in the rim bubbles per unit rim volume could be derived by a summation of the number of Xe atoms of each rim bubble in a unit rim volume. The number of Xe atoms of each rim bubble could be calculated by the Van der Waals equation of state and the pressure expressed by p=σ+C/r, where C is an unknown constant to be determined as a function of the temperature and the burnup. On the other hand, the total number of Xe atoms in the rim bubbles per unit rim volume can also be calculated by Xe depression data. If the fuel pellet is not restrained, the uniform hydrostatic stress, σ is zero. Hence if the data of the fuel disk without a restraint is used, a constant C can be obtained at 823K and a local burnup of 90 GWd/t. Although the local burnup of PCMI restraint case is slightly different from that without PCMI restraint, the value derived above is used for the analysis of PCMI restraint case. The calculated bubble distribution with PCMI restraint was similar to the measured one. Because the effect of PCMI restraint on bubble size increased with the bubble size, the development of a large bubble was suppressed. Hence, the PCMI restraint caused a typical bubble size in the rim and

  11. Dietary restraint in college women: fear of an imperfect fat self is stronger than hope of a perfect thin self.

    Science.gov (United States)

    Dalley, Simon E; Toffanin, Paolo; Pollet, Thomas V

    2012-09-01

    We predicted that the perceived likelihood of acquiring a hoped-for thin self would mediate perfectionistic strivings on dietary restraint, and that the perceived likelihood of acquiring a feared fat self would mediate perfectionistic concerns on dietary restraint. We also predicted that the mediation pathway from perfectionistic concerns to dietary restraint would have a greater impact than that from perfectionistic strivings. Participants were 222 female college students who reported their height and weight and completed measures of perfectionism, the likelihood of acquiring the feared fat and hoped-for thin selves, and dietary restraint. Statistical analyses revealed that the perceived likelihood of acquiring the feared fat self mediated both perfectionistic concerns and perfectionistic strivings on dietary restraint, and that the mediating pathway from perfectionistic concerns to dietary restraint was greater than that from perfectionistic strivings. Implications for future research and eating pathology interventions are discussed. Copyright © 2012 Elsevier Ltd. All rights reserved.

  12. THE LANDSCAPE OF THE NEUTRINO MECHANISM OF CORE-COLLAPSE SUPERNOVAE: NEUTRON STAR AND BLACK HOLE MASS FUNCTIONS, EXPLOSION ENERGIES, AND NICKEL YIELDS

    International Nuclear Information System (INIS)

    Pejcha, Ondřej; Thompson, Todd A.

    2015-01-01

    If the neutrino luminosity from the proto-neutron star formed during a massive star core collapse exceeds a critical threshold, a supernova (SN) results. Using spherical quasi-static evolutionary sequences for hundreds of progenitors over a range of metallicities, we study how the explosion threshold maps onto observables, including the fraction of successful explosions, the neutron star (NS) and black hole (BH) mass functions, the explosion energies (E SN ) and nickel yields (M Ni ), and their mutual correlations. Successful explosions are intertwined with failures in a complex pattern that is not simply related to initial progenitor mass or compactness. We predict that progenitors with initial masses of 15 ± 1, 19 ± 1, and ∼21-26 M ☉ are most likely to form BHs, that the BH formation probability is non-zero at solar-metallicity and increases significantly at low metallicity, and that low luminosity, low Ni-yield SNe come from progenitors close to success/failure interfaces. We qualitatively reproduce the observed E SN -M Ni correlation, we predict a correlation between the mean and width of the NS mass and E SN distributions, and that the means of the NS and BH mass distributions are correlated. We show that the observed mean NS mass of ≅ 1.33 M ☉ implies that the successful explosion fraction is higher than 0.35. Overall, we show that the neutrino mechanism can in principle explain the observed properties of SNe and their compact objects. We argue that the rugged landscape of progenitors and outcomes mandates that SN theory should focus on reproducing the wide ranging distributions of observed SN properties

  13. Mechanism of in situ surface polymerization of gallic acid in an environmental-inspired preparation of carboxylated core-shell magnetite nanoparticles.

    Science.gov (United States)

    Tóth, Ildikó Y; Szekeres, Márta; Turcu, Rodica; Sáringer, Szilárd; Illés, Erzsébet; Nesztor, Dániel; Tombácz, Etelka

    2014-12-30

    Magnetite nanoparticles (MNPs) with biocompatible coatings are good candidates for MRI (magnetic resonance imaging) contrasting, magnetic hyperthermia treatments, and drug delivery systems. The spontaneous surface induced polymerization of dissolved organic matter on environmental mineral particles inspired us to prepare carboxylated core-shell MNPs by using a ubiquitous polyphenolic precursor. Through the adsorption and in situ surface polymerization of gallic acid (GA), a polygallate (PGA) coating is formed on the nanoparticles (PGA@MNP) with possible antioxidant capacity. The present work explores the mechanism of polymerization with the help of potentiometric acid-base titration, dynamic light scattering (for particle size and zeta potential determination), UV-vis (UV-visible light spectroscopy), FTIR-ATR (Fourier-transformed infrared spectroscopy by attenuated total reflection), and XPS (X-ray photoelectron spectroscopy) techniques. We observed the formation of ester and ether linkages between gallate monomers both in solution and in the adsorbed state. Higher polymers were formed in the course of several weeks both on the surface of nanoparticles and in the dispersion medium. The ratio of the absorbances of PGA supernatants at 400 and 600 nm (i.e., the E4/E6 ratio commonly used to characterize the degree of polymerization of humic materials) was determined to be 4.3, similar to that of humic acids. Combined XPS, dynamic light scattering, and FTIR-ATR results revealed that, prior to polymerization, the GA monomers became oxidized to poly(carboxylic acid)s due to ring opening while Fe(3+) ions reduced to Fe(2+). Our published results on the colloidal and chemical stability of PGA@MNPs are referenced thoroughly in the present work. Detailed studies on biocompatibility, antioxidant property, and biomedical applicability of the particles will be published.

  14. Investigation of mechanical properties of hydrate-bearing pressure core sediments recovered from the Eastern Nankai Trough using transparent acrylic cell triaxial testing system (TACTT-system)

    Science.gov (United States)

    Yoneda, J.; Masui, A.; Konno, Y.; Jin, Y.; Kida, M.; Suzuki, K.; Nakatsuka, Y.; Tenma, N.; Nagao, J.

    2014-12-01

    Natural gas hydrate-bearing pressure core sediments have been sheared in compression using a newly developed Transparent Acrylic Cell Triaxial Testing (TACTT) system to investigate the geophysical and geomechanical behavior of sediments recovered from the deep seabed in the Eastern Nankai Trough, the first Japanese offshore production test region. The sediments were recovered by hybrid pressure core system (hybrid PCS) and pressure cores were cut by pressure core analysis tools (PCATs) on board. These pressure cores were transferred to the AIST Hokkaido centre and trimmed by pressure core non-destructive analysis tools (PNATs) for TACTT system which maintained the pressure and temperature conditions within the hydrate stability boundary, through the entire process of core handling from drilling to the end of laboratory testing. An image processing technique was used to capture the motion of sediment in a transparent acrylic cell, and digital photographs were obtained at every 0.1% of vertical strain during the test. Analysis of the optical images showed that sediments with 63% hydrate saturation exhibited brittle failure, although nonhydrate-bearing sediments exhibited ductile failure. In addition, the increase in shear strength with hydrate saturation increase of natural gas hydrate is in agreement with previous data from synthetic gas hydrate. This research was financially supported by the Research Consortium for Methane Hydrate Resources in Japan (MH21 Research Consortium) that carries out Japan's Methane Hydrate R&D Program by the Ministry of Economy, Trade and Industry (METI).

  15. Ice Cores

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Records of past temperature, precipitation, atmospheric trace gases, and other aspects of climate and environment derived from ice cores drilled on glaciers and ice...

  16. Algorithm for selection of optimized EPR distance restraints for de novo protein structure determination

    Science.gov (United States)

    Kazmier, Kelli; Alexander, Nathan S.; Meiler, Jens; Mchaourab, Hassane S.

    2010-01-01

    A hybrid protein structure determination approach combining sparse Electron Paramagnetic Resonance (EPR) distance restraints and Rosetta de novo protein folding has been previously demonstrated to yield high quality models (Alexander et al., 2008). However, widespread application of this methodology to proteins of unknown structures is hindered by the lack of a general strategy to place spin label pairs in the primary sequence. In this work, we report the development of an algorithm that optimally selects spin labeling positions for the purpose of distance measurements by EPR. For the α-helical subdomain of T4 lysozyme (T4L), simulated restraints that maximize sequence separation between the two spin labels while simultaneously ensuring pairwise connectivity of secondary structure elements yielded vastly improved models by Rosetta folding. 50% of all these models have the correct fold compared to only 21% and 8% correctly folded models when randomly placed restraints or no restraints are used, respectively. Moreover, the improvements in model quality require a limited number of optimized restraints, the number of which is determined by the pairwise connectivities of T4L α-helices. The predicted improvement in Rosetta model quality was verified by experimental determination of distances between spin labels pairs selected by the algorithm. Overall, our results reinforce the rationale for the combined use of sparse EPR distance restraints and de novo folding. By alleviating the experimental bottleneck associated with restraint selection, this algorithm sets the stage for extending computational structure determination to larger, traditionally elusive protein topologies of critical structural and biochemical importance. PMID:21074624

  17. Physical restraint use among nursing home residents: A comparison of two data collection methods

    Directory of Open Access Journals (Sweden)

    Voyer Philippe

    2004-10-01

    Full Text Available Abstract Background In view of the issues surrounding physical restraint use, it is important to have a method of measurement as valid and reliable as possible. We determined the sensitivity and specificity of physical restraint use a reported by nursing staff and b reviewed from medical and nursing records in nursing home settings, by comparing these methods with direct observation. Methods We sampled eight care units in skilled nursing homes, seven care units in nursing homes and one long-term care unit in a hospital, from eight facilities which included 28 nurses and 377 residents. Physical restraint use was assessed the day following three periods of direct observation by two different means: interview with one or several members of the regular nursing staff, and review of medical and nursing records. Sensitivity and specificity values were calculated according to 2-by-2 contingency tables. Differences between the methods were assessed using the phi coefficient. Other information collected included: demographic characteristics, disruptive behaviors, body alignment problems, cognitive and functional skills. Results Compared to direct observation (gold standard, reported restraint use by nursing staff yielded a sensitivity of 87.4% at a specificity of 93.7% (phi = 0.84. When data was reviewed from subjects' medical and nursing records, sensitivity was reduced to 74.8%, and specificity to 86.3% (phi = 0.54. Justifications for restraint use including risk for falls, agitation, body alignment problems and aggressiveness were associated with the use of physical restraints. Conclusions The interview of nursing staff and the review of medical and nursing records are both valid and reliable techniques for measuring physical restraint use among nursing home residents. Higher sensitivity and specificity values were achieved when nursing staff was interviewed as compared to reviewing medical records. This study suggests that the interview of nursing

  18. Effectiveness of a multifactorial intervention to reduce physical restraints in nursing home residents.

    Science.gov (United States)

    Koczy, Petra; Becker, Clemens; Rapp, Kilian; Klie, Thomas; Beische, Denis; Büchele, Gisela; Kleiner, Andrea; Guerra, Virginia; Rissmann, Ulrich; Kurrle, Susan; Bredthauer, Doris

    2011-02-01

    To evaluate the effectiveness of a multifactorial intervention to reduce the use of physical restraints in residents of nursing homes. Cluster-randomized controlled trial. Forty-five nursing homes in Germany. Three hundred thirty-three residents who were being restrained at the start of the intervention. Persons responsible for the intervention in the nursing homes attended a 6-hour training course that included education about the reasons restraints are used, the adverse effects, and alternatives to their use. Technical aids, such as hip protectors and sensor mats, were provided. The training was designed to give the change agents tools for problem-solving to prevent behavioral symptoms and injuries from falls without using physical restraints. The main outcome was the complete cessation of physical restraint use on 3 consecutive days 3 months after the start of the intervention. Secondary outcomes were partial reductions in restraint use, percentage of fallers, number of psychoactive drugs, and occurrence of behavioral symptoms. The probability of being unrestrained in the intervention group (IG) was more than twice that in the control group (CG) at the end of the study (odds ratio=2.16, 95% confidence interval=1.05-4.46). A partial reduction of restraint use was also about twice as often achieved in the IG as in the CG. No negative effect was observed regarding medication or behavioral symptoms. The percentage of fallers was higher in the IG. The intervention reduced restraint use without a significant increase in falling, behavioral symptoms, or medication. © 2011, Copyright the Authors. Journal compilation © 2011, The American Geriatrics Society.

  19. Use of top tethers with forward-facing child restraints: observations and driver interviews.

    Science.gov (United States)

    Eichelberger, Angela H; Decina, Lawrence E; Jermakian, Jessica S; McCartt, Anne T

    2014-02-01

    Despite the safety benefits, many parents do not use top tethers with forward-facing child restraints. Detailed information was collected about why parents are not using tethers. The sample included 479 drivers who had forward-facing child restraints installed in passenger vehicles equipped with tether anchors. The survey was conducted primarily at shopping centers, recreation facilities, child care facilities, car seat check events, and health care facilities in mostly suburban areas surrounding Philadelphia, Washington, DC, Fredericksburg (VA), and Seattle. Drivers were surveyed about their knowledge and use of tethers and experience with child restraints. Tether use was observed to verify whether tethers were being used correctly. Fifty-six percent of forward-facing child restraints were installed with the tether; 39% were installed with the tether used correctly. The tether was used with 71% of LATCH lower anchor installations and 33% of seat belt installations. Drivers who installed child restraints without tethers most often said they did not know about the tether or how to use it. Although the tether use rate was slightly higher in the current research than in previous studies, many parents and caregivers still use forward-facing child restraints without attaching the tether. Because the main problem is lack of awareness of the tether or how to use it, public education should focus specifically on the safety benefits of tethers and how to use them. Information about why caregivers fail to use top tethers is potentially useful to child restraint manufacturers, child passenger safety technicians, and others who work with parents to improve motor vehicle safety. Copyright © 2013 Elsevier Ltd and National Safety Council. All rights reserved.

  20. Cardiovascular and hormonal responses of conscious pigs during physical restraint

    International Nuclear Information System (INIS)

    Wade, C.E.; Bossone, C.A.; Hannon, J.P.; Hunt, M.M.; Rodkey, W.G.

    1986-01-01

    We investigated the effect of physical restraint on cardiovascular function and plasma hormone levels in 20 to 25 kg conscious Duroc pigs. Pigs were placed in a Pavlov sling or remained in a portable holding cage. Blood pressure and heart rate were monitored and blood samples taken at 0, 2.5, 5, 10, 30, 60, 120 and 240 min. Placement into the sling increased heart rate from 106 ''+ or -'' 3 to 151 ''+ or -'' 13 beats/min and mean arterial pressure rose from 95 ''+ or -'' 2 to 115 ''+ or -'' 2 mm Hg. Both heart rate and blood pressure returned to basal values within 10 min. Hematocrit was increased from 26 ''+ or -'' 1 to 32 ''+ or -'' 1%. Heart rate, blood pressure and hematocrit were not changed in caged animals. Plasma norepinephrine increased from 179 ''+ or -'' 32 to 461 ''+ or -'' 52 pg/ml returning to basal values within 10 min. Epinephrine showed a similar trend rising from 69 ''+ or -'' 10 to 337 ''+ or -'' 53 pg/ml. Plasma renin activity increased after 5 min in the sling and remained increased from a basal level of 1.0 ''+ or -'' 0.2 to 2.8 ''+ or -'' 0.5 ng AI/ml/hr at four hr. Plasma cortisol (4.5 ''+ or -'' 0.6 to 8.2 ''+ or -'' 1.5 microg/dl), ACTH (45 ''+ or -'' 9 to 169 ''+ or -'' pg/ml) and aldosterone (3.5 ''+ or -'' 0.4 to 11.2 ''+ or -'' 1.1 ng/dl) rose over the four hr period. Pigs in cages showed no change in plasma hormones. Placement of an untrained pig into a sling raises heart rate, blood pressure and hematocrit and produces increases in plasma concentrations of epinephrine, ACTH, cortisol and aldosterone

  1. Women, sex and marriage. Restraint as a feminine strategy.

    Science.gov (United States)

    Kishwar, M

    1997-01-01

    The expression of sexuality varies in different cultures, and most societies attempt to control sexuality through the institution of marriage. In the West, the availability of cheap, effective contraceptives separated sex from reproduction and promoted the sexual liberation of women. Today, while divorce is common, sexually liberated people nevertheless engage in a form of serial monogamy. Sexual liberation in the West causes women to be exploited by men and creates instability in nuclear families. In India, feminism is tempered by a belief that familial rights have precedence over individual rights. India women practice sexual self-denial after being widowed to protect their children and to gain power and respect in the community. The power of chastity was illustrated by Mahatma Gandhi who marshalled his spiritual forces to fight for independence. The stories of many individual women illustrate how they attain status and prestige through chastity. Other women maintain absolute marital faithfulness as a marital strategy to control wayward husbands. These women deemphasize their roles as wives and emphasize their roles as mothers. The children of such women often recognize their sacrifices and become their strongest allies. On the other hand, examples of women who have chosen sexual freedom show that such a choice places them at the mercy of men, makes them social outcasts, and causes other women to distrust them as competitors for their husbands. In patriarchal societies, women can not win if they try to mimic men's capacity for irresponsible sex. Sexual freedom can only work for women in matrilineal communities that shun marriage in favor of strong ties within a woman's natal family. Indian women rooted in the extended family enjoy the resilience and flexibility attendant upon playing a larger role than simply pleasing men. Opting for sexual restraint can be an effective though costly strategy to achieve the sympathy and support of an extended family when a man is

  2. Restraint stress intensifies interstitial K+ accumulation during severe hypoxia

    Directory of Open Access Journals (Sweden)

    Christian eSchnell

    2012-03-01

    Full Text Available Chronic stress affects neuronal networks by inducing dendritic retraction, modifying neuronal excitability and plasticity, and modulating glial cells. To elucidate the functional consequences of chronic stress for the hippocampal network, we submitted adult rats to daily restraint stress for three weeks (6 h/day. In acute hippocampal tissue slices of stressed rats, basal synaptic function and short-term plasticity at Schaffer collateral/CA1 neuron synapses were unchanged while long-term potentiation was markedly impaired. The spatiotemporal propagation pattern of hypoxia-induced spreading depression episodes was indistinguishable among control and stress slices. However, the duration of the extracellular direct current (DC potential shift was shortened after stress. Moreover, K+ fluxes early during hypoxia were more intense, and the postsynaptic recoveries of interstitial K+ levels and synaptic function were slower. Morphometric analysis of immunohistochemically stained sections suggested hippocampal shrinkage in stressed rats, and the number of cells that are immunoreactive for GFAP (glial fibrillary acidic protein was increased in the CA1 subfield indicating activation of astrocytes. Western blots showed a marked downregulation of the inwardly rectifying K+ channel Kir4.1 in stressed rats. Yet, resting membrane potentials, input resistance and K+-induced inward currents in CA1 astrocytes were indistinguishable from controls. These data indicate an intensified interstitial K+ accumulation during hypoxia in the hippocampus of chronically stressed rats which seems to arise from a reduced interstitial volume fraction rather than impaired glial K+ buffering. One may speculate that chronic stress aggravates hypoxia-induced pathophysiological processes in the hippocampal network and that this has implications for the ischemic brain.

  3. Mechanical spectral shift reactor

    International Nuclear Information System (INIS)

    Sherwood, D.G.; Wilson, J.F.; Salton, R.B.; Fensterer, H.F.

    1982-01-01

    A mechanical spectral shift reactor comprises apparatus for inserting and withdrawing water displacer elements from the reactor core for selectively changing the water-moderator volume in the core thereby changing the reactivity of the core. The apparatus includes drive mechanisms for moving the displacer elements relative to the core and guide mechanisms for guiding the displacer rods through the reactor vessel. (author)

  4. Optimising product advice based on age when design criteria are based on weight: child restraints in vehicles.

    Science.gov (United States)

    Anderson, R W G; Hutchinson, T P

    2009-03-01

    The motivation for this paper is the high rate of inappropriate child restraint selection in cars that is apparent in published surveys of child restraint use and how the public health messages promoting child restraints might respond. Advice has increasingly been given solely according to the child's weight, while many parents do not know the weight of their children. A common objection to promoting restraint use based on the age of the child is the imprecision of such advice, given the variation in the size of children, but the magnitude of the misclassification such advice would produce has never been estimated. This paper presents a method for estimating the misclassification of children by weight, when advice is posed in terms of age, and applies it to detailed child growth data published by the Centers for Disease Control and Prevention. In Australia, guidelines instructing all parents to promote their children from an infant restraint to a forward-facing child seat at 6 months, and then to a belt-positioning booster at 4 years, would mean that 5% of all children under the age of 6 years would be using a restraint not suited to their weight. Coordination of aged-based advice and the weight ranges chosen for the Australian Standard on child restraints could reduce this level of misclassification to less than 1%. The general method developed may also be applied to other aspects of restraint design that are more directly relevant to good restraint fit.

  5. Single-molecule fluorescence measurements reveal the reaction mechanisms of the core RISC, composed of human Argonaute 2 and a guide RNA.

    Science.gov (United States)

    Jo, Myung Hyun; Song, Ji-Joon; Hohng, Sungchul

    2015-12-01

    In eukaryotes, small RNAs play important roles in both gene regulation and resistance to viral infection. Argonaute proteins have been identified as a key component of the effector complexes of various RNA-silencing pathways, but the mechanistic roles of Argonaute proteins in these pathways are not clearly understood. To address this question, we performed single-molecule fluorescence experiments using an RNA-induced silencing complex (core-RISC) composed of a small RNA and human Argonaute 2. We found that target binding of core-RISC starts at the seed region of the guide RNA. After target binding, four distinct reactions followed: target cleavage, transient binding, stable binding, and Argonaute unloading. Target cleavage required extensive sequence complementarity and accelerated core-RISC dissociation for recycling. In contrast, the stable binding of core-RISC to target RNAs required seed-match only, suggesting a potential explanation for the seed-match rule of microRNA (miRNA) target selection.

  6. Pasireotide treatment does not modify hyperglycemic and corticosterone acute restraint stress responses in rats.

    Science.gov (United States)

    Ribeiro-Oliveira, Antônio; Schweizer, Junia R O L; Amaral, Pedro H S; Bizzi, Mariana F; Silveira, Warley Cezar da; Espirito-Santo, Daniel T A; Zille, Giancarlo; Soares, Beatriz S; Schmid, Herbert A; Yuen, Kevin C J

    2018-04-17

    Pasireotide is a new-generation somatostatin analog that acts through binding to multiple somatostatin receptor subtypes. Studies have shown that pasireotide induces hyperglycemia, reduces glucocorticoid secretion, alters neurotransmission, and potentially affects stress responses typically manifested as hyperglycemia and increased corticosterone secretion. This study specifically aimed to evaluate whether pasireotide treatment modifies glucose and costicosterone secretion in response to acute restraint stress. Male Holtzman rats of 150-200 g were treated with pasireotide (10 µg/kg/day) twice-daily for two weeks or vehicle for the same period. Blood samples were collected at baseline and after 5, 10, 30, and 60 min of restraint stress. The three experimental groups comprised of vehicle + restraint (VEHR), pasireotide + restraint (PASR), and pasireotide + saline (PASNR). Following pasireotide treatment, no significant differences in baseline glucose and corticosterone levels were observed among the three groups. During restraint, hyperglycemia was observed at 10 min (p stressed groups when compared to the non-stressed PASNR group (p stressed groups at 5 min (p stressed PASNR group (p stress responses, thus preserving acute stress regulation.

  7. Chemical restraint in routine clinical practice: a report from a general hospital psychiatric ward in Greece

    Directory of Open Access Journals (Sweden)

    Papamichael Georgios

    2011-02-01

    Full Text Available Abstract Background There is a dearth of studies regarding chemical restraint in routine clinical psychiatric practice. There may be wide variations between different settings and countries. Methods A retrospective study on chemical restraint was performed in the 11-bed psychiatric ward of the General Hospital of Arta, in northwestern Greece. All admissions over a 2-year-period (from March 2008 to March 2010 were examined. Results Chemical restraint was applied in 33 cases (10.5% of total admissions. From a total of 82 injections, 22 involved a benzodiazepine and/or levomepromazine, whereas 60 injections involved an antipsychotic agent, almost exclusively haloperidol (96.7% of cases, usually in combination with a benzodiazepine (61.7% of cases. In 36.4% of cases the patient was further subjected to restraint or seclusion. Conclusions In our unit, clinicians prefer the combined antipsychotic/benzodiazepine regimen for the management of patients' acute agitation and violent behaviour. Conventional antipsychotics are administrated almost exclusively and in a significant proportion of cases further coercive measures are applied. Studies on the practice of chemical restraint should be regularly performed in clinical settings.

  8. Psychological assessment of acute schizophrenia patients who experienced seclusion either alone or in combination with restraint.

    Science.gov (United States)

    Eguchi, Rika; Onozuka, Daisuke; Ikeda, Kouji; Kuroda, Kenji; Ieiri, Ichiro; Hagihara, Akihito

    2018-05-01

    Objective Numerous studies on the effects of seclusion and/or restraint in acute psychiatric treatment have reported both positive and negative effects. However, no studies to date have evaluated the effects of seclusion and/or restraint on schizophrenia patients using a rating scale. Thus, to examine the effects of seclusion and/or restraint on schizophrenia patients, we used the Brief Psychiatric Rating Scale and assessed the psychological condition of patients. Methods Factor analysis was conducted to create subscales of Brief Psychiatric Rating Scale, and psychiatric changes were assessed with respect to each subscale using multiple logistic regression analyses. Analyses were performed on three groups (i.e. entire, higher functioning, and lower functioning groups) involving a total of 1559 schizophrenia patients aged 18 to 65 years. Results In the entire and lower functioning groups, seclusion was a significant predictor of improvements related to the "hostility/suspiciousness" subscale. Seclusion combined with restraint was associated with improvements related to the "psychosis/thinking disorder" subscale. In the higher functioning group, there were no significant predictors. Conclusions It is implied that seclusion and/or restraint is related to improved psychiatric symptoms only among patients whose functioning is impaired. To verify the present findings, further studies involving multiple sites and additional psychiatric measures are necessary.

  9. Vessel core seismic interaction for a fast reactor

    International Nuclear Information System (INIS)

    Martelli, A.; Maresca, G.

    1984-01-01

    This report deals with the analysis carried out in collaboration between ENEA and NIRA for optimizing the iterative procedure applied for the evaluation of the effects of the vessel core dynamic interaction for a fast reactor in the case of a earthquake. In fact, as shown in a previous report the convergence of such procedure was very slow for the design solution adopted for the PEC reactor, i.e. with a core restraint plate located close to the top of the core elements. This study, although performed making use of preliminary data (the same of the cited previous report) demonstrates that the convergence is fast if a suitable linear core model is applied in the first iteration linear calculations carried out by NIRA, with an intermediate stiffness with respect to those corresponding to the two limit models previously assumed and increased damping coefficients. Thus, the optimized iterative procedures is now applied in the PEC reactor block seismic verification analysis

  10. The relational neurobehavioral approach: can a non-aversive program manage adults with brain injury-related aggression without seclusion/restraint?

    Science.gov (United States)

    Kalapatapu, Raj K; Giles, Gordon M

    2017-11-01

    The Relational Neurobehavioral Approach (RNA) is a set of non-aversive intervention methods to manage individuals with brain injury-related aggression. New data on interventions used in the RNA and on how the RNA interventions can be used with patients with acquired brain injury (ABI) who have differing levels of functional impairment are provided in this paper. The study was conducted over a 6-week period in a secure 65-bed program for individuals with ABI that is housed in two units of a skilled nursing facility (SNF). Implementation of the RNA was compared between two units that housed patients with differing levels of functional impairment (n = 65 adults). Since this was a hierarchical clustered dataset, Generalized Estimating Equations regression was used in the analyses. RNA interventions used to manage the 495 aggressive incidents included the following: Aggression ignored, Closer observation, Talking to patient, Reassurance, Physical distraction, Isolation without seclusion, Immediate medication by mouth, Holding patient. Different interventions were implemented differentially by staff based on level of functional impairment and without use of seclusion or mechanical restraint. The RNA can be used to non-aversively manage aggression in patients with brain injury and with differing levels of functional impairment. Programs adopting the RNA can potentially manage brain injury-related aggression without seclusion or mechanical restraint. Implications for Rehabilitation The Relational Neurobehavioral Approach (RNA) is a set of non-aversive intervention methods to manage individuals with brain injury-related aggression. RNA methods can be used to manage aggression in patients with brain injury who have differing levels of functional impairment. Successful implementation of the RNA may allow for the management of brain injury-related aggression without seclusion or mechanical restraint.

  11. Physical restraint and the protection of the human rights of immigration detainees in hospitals.

    Science.gov (United States)

    Pickles, Hilary; Norton, Emma; Ginn, Emma; Schleicher, Theresa

    2015-08-01

    Immigration detainees, like prisoners, are entitled to the same standard of healthcare as non-detained patients. When hospital attendance or admission is required, the priority for custodial staff (who for purposes of this article we refer to as 'escorts') is to prevent absconding. For that reason, they may wish to use physical restraints, such as handcuffs, and remain with the detainee at all times. This can be degrading for the patient and breach their human rights. Clinicians have professional obligations to all their patients and must object to any restraint methods that risk damaging the patient's right to confidentiality, treatment, health or the therapeutic relationship itself. The starting presumption is that restraints ought not to be used during treatment and only in the most exceptional cases ought escorts to be present during clinical examination or treatment. © Royal College of Physicians 2015. All rights reserved.

  12. Greater hunger and less restraint predict weight loss success with phentermine treatment.

    Science.gov (United States)

    Thomas, Elizabeth A; Mcnair, Bryan; Bechtell, Jamie L; Ferland, Annie; Cornier, Marc-Andre; Eckel, Robert H

    2016-01-01

    Phentermine is thought to cause weight loss through a reduction in hunger. It was hypothesized that higher hunger ratings would predict greater weight loss with phentermine. This is an observational pilot study in which all subjects were treated with phentermine for 8 weeks and appetite and eating behaviors were measured at baseline and week 8. Outcomes were compared in subjects with ≥5% vs. hunger (P = 0.017), desire to eat (P =0.003), and prospective food consumption (0.006) and lower baseline cognitive restraint (P = 0.01). In addition, higher baseline home prospective food consumption (P = 0.002) and lower baseline cognitive restraint (P hunger and less restraint are more likely to achieve significant weight loss with phentermine. This information can be used clinically to determine who might benefit most from phentermine treatment. © 2015 The Obesity Society.

  13. Geometrically Nonlinear Transient Response of Laminated Plates with Nonlinear Elastic Restraints

    Directory of Open Access Journals (Sweden)

    Shaochong Yang

    2017-01-01

    Full Text Available To investigate the dynamic behavior of laminated plates with nonlinear elastic restraints, a varied constraint force model and a systematic numerical procedure are presented in this work. Several kinds of typical relationships of force-displacement for spring are established to simulate the nonlinear elastic restraints. In addition, considering the restraining moments of flexible pads, the pads are modeled by translational and rotational springs. The displacement- dependent constraint forces are added to the right-hand side of equations of motion and treated as additional applied loads. These loads can be explicitly defined, via an independent set of nonlinear load functions. The time histories of transverse displacements at typical points of the laminated plate are obtained through the transient analysis. Numerical examples show that the present method can effectively treat the geometrically nonlinear transient response of plates with nonlinear elastic restraints.

  14. How Farm Animals React and Perceive Stressful Situations Such As Handling, Restraint, and Transport

    Directory of Open Access Journals (Sweden)

    Temple Grandin

    2015-12-01

    Full Text Available An animal that has been carefully acclimated to handling may willingly re-enter a restrainer. Another animal may have an intense agitated behavioral reaction or refuse to re-enter the handling facility. Physiological measures of stress such as cortisol may be very low in the animal that re-enters willingly and higher in animals that actively resist restraint. Carefully acclimating young animals to handling and restraint can help improve both productivity and welfare by reducing fear stress. Some of the topics covered in this review are: How an animal perceives handling and restraint, the detrimental effects of a sudden novel event, descriptions of temperament and aversion tests and the importance of good stockmanship.

  15. Mechanics

    CERN Document Server

    Hartog, J P Den

    1961-01-01

    First published over 40 years ago, this work has achieved the status of a classic among introductory texts on mechanics. Den Hartog is known for his lively, discursive and often witty presentations of all the fundamental material of both statics and dynamics (and considerable more advanced material) in new, original ways that provide students with insights into mechanical relationships that other books do not always succeed in conveying. On the other hand, the work is so replete with engineering applications and actual design problems that it is as valuable as a reference to the practicing e

  16. Reactor core

    International Nuclear Information System (INIS)

    Matsuura, Tetsuaki; Nomura, Teiji; Tokunaga, Kensuke; Okuda, Shin-ichi

    1990-01-01

    Fuel assemblies in the portions where the gradient of fast neutron fluxes between two opposing faces of a channel box is great are kept loaded at the outermost peripheral position of the reactor core also in the second operation cycle in the order to prevent interference between a control rod and the channel box due to bending deformation of the channel box. Further, the fuel assemblies in the second row from the outer most periphery in the first operation cycle are also kept loaded at the second row in the second operation cycle. Since the gradient of the fast neutrons in the reactor core is especially great at the outer circumference of the reactor core, the channel box at the outer circumference is bent such that the surface facing to the center of the reactor core is convexed and the channel box in the second row is also bent to the identical direction, the insertion of the control rod is not interfered. Further, if the positions for the fuels at the outermost periphery and the fuels in the second row are not altered in the second operation cycle, the gaps are not reduced to prevent the interference between the control rod and the channel box. (N.H.)

  17. Use of physical restraints and antipsychotic medications in nursing homes: a cross-national study.

    Science.gov (United States)

    Feng, Zhanlian; Hirdes, John P; Smith, Trevor F; Finne-Soveri, Harriet; Chi, Iris; Du Pasquier, Jean-Noel; Gilgen, Ruedi; Ikegami, Naoki; Mor, Vincent

    2009-10-01

    This study compares inter- and intra-country differences in the prevalence of physical restraints and antipsychotic medications in nursing homes, and examines aggregated resident conditions and organizational characteristics correlated with these treatments. Population-based, cross-sectional data were collected using a standardized Resident Assessment Instrument (RAI) from 14,504 long-term care facilities providing nursing home level services in five countries participating in the interRAI consortium, including Canada, Finland, Hong Kong (Special Administrative Region, China), Switzerland, and the United States. Facility-level prevalence rates of physical restraints and antipsychotic use were examined both between and within the study countries. The prevalence of physical restraint use varied more than five-fold across the study countries, from an average 6% in Switzerland, 9% in the US, 20% in Hong Kong, 28% in Finland, and over 31% in Canada. The prevalence of antipsychotic use ranged from 11% in Hong Kong, between 26-27% in Canada and the US, 34% in Switzerland, and nearly 38% in Finland. Within each country, substantial variations existed across facilities in both physical restraint and antipsychotic use rates. In all countries, neither facility case mix nor organizational characteristics were particularly predictive of the prevalence of either treatment. There exists large, unexplained variability in the prevalence of physical restraint and antipsychotic use in nursing home facilities both between and within countries. Since restraints and antipsychotics are associated with adverse outcomes, it is important to understand the idiosyncratic factors specific to each country that contribute to variation in use rates. Copyright (c) 2009 John Wiley & Sons, Ltd.

  18. Exploiting structure similarity in refinement: automated NCS and target-structure restraints in BUSTER

    Energy Technology Data Exchange (ETDEWEB)

    Smart, Oliver S., E-mail: osmart@globalphasing.com; Womack, Thomas O.; Flensburg, Claus; Keller, Peter; Paciorek, Włodek; Sharff, Andrew; Vonrhein, Clemens; Bricogne, Gérard [Global Phasing Ltd, Sheraton House, Castle Park, Cambridge CB3 0AX (United Kingdom)

    2012-04-01

    Local structural similarity restraints (LSSR) provide a novel method for exploiting NCS or structural similarity to an external target structure. Two examples are given where BUSTER re-refinement of PDB entries with LSSR produces marked improvements, enabling further structural features to be modelled. Maximum-likelihood X-ray macromolecular structure refinement in BUSTER has been extended with restraints facilitating the exploitation of structural similarity. The similarity can be between two or more chains within the structure being refined, thus favouring NCS, or to a distinct ‘target’ structure that remains fixed during refinement. The local structural similarity restraints (LSSR) approach considers all distances less than 5.5 Å between pairs of atoms in the chain to be restrained. For each, the difference from the distance between the corresponding atoms in the related chain is found. LSSR applies a restraint penalty on each difference. A functional form that reaches a plateau for large differences is used to avoid the restraints distorting parts of the structure that are not similar. Because LSSR are local, there is no need to separate out domains. Some restraint pruning is still necessary, but this has been automated. LSSR have been available to academic users of BUSTER since 2009 with the easy-to-use -autoncs and @@target target.pdb options. The use of LSSR is illustrated in the re-refinement of PDB entries http://scripts.iucr.org/cgi-bin/cr.cgi?rm, where -target enables the correct ligand-binding structure to be found, and http://scripts.iucr.org/cgi-bin/cr.cgi?rm, where -autoncs contributes to the location of an additional copy of the cyclic peptide ligand.

  19. Improving Working Conditions for Astronauts: An Electronic Personal Restraint System for Use in Microgravity Environments

    Directory of Open Access Journals (Sweden)

    Kevin Tait

    2012-01-01

    Full Text Available While in microgravity, astronauts are preoccupied with physical restraint, which takes attention away from the maintenance task or scientific experiment at hand. This may directly lead to safety concerns and increased time for extravehicular activity, as well as potentially inhibit or corrupt data collection. A primary concern is the time it takes to manipulate the current restraint system. The portable foot restraint currently in use by NASA employs a series of pins in order to engage the system or release in an emergency. This requires considerable time for the user to detach, and there is an increased risk of entanglement. If restraint operating time could be reduced by 50%, the astronaut’s assigned experiment time could be increased an average of 100 minutes per mission. Another problem identified by NASA included the inability of the current system to release the user upon failure. Research and design was conducted following the Six-Sigma DMEDI project architecture, and a new form of restraint to replace the existing system was proposed. The research team first studied the customer requirements and relevant standards set by NASA, and with this information they began drafting designs for a solution. This project utilized electromagnetism to restrain a user in microgravity. The proposed system was capable of being manipulated quickly, failing in a manner that released the user, and being electronically controlled. This active electronic control was a new concept in restraint systems, as it enabled an astronaut to effectively “walk” along a surface while remaining restrained to it. With the design prototype and a limited budget, a rudimentary test assembly was built by the team, and most of NASA’s specifications were met. With recommendations from NASA, the research team concluded by developing potential material and design solutions that can be explored in the future by Purdue University or other parties.

  20. A new approach for applying residual dipolar couplings as restraints in structure elucidation

    International Nuclear Information System (INIS)

    Meiler, Jens; Blomberg, Niklas; Nilges, Michael; Griesinger, Christian

    2000-01-01

    Residual dipolar couplings are useful global structural restraints. The dipolar couplings define the orientation of a vector with respect to the alignment tensor. Although the size of the alignment tensor can be derived from the distribution of the experimental dipolar couplings, its orientation with respect to the coordinate system of the molecule is unknown at the beginning of structure determination. This causes convergence problems in the simulated annealing process. We therefore propose a protocol that translates dipolar couplings into intervector projection angles, which are independent of the orientation of the alignment tensor with respect to the molecule. These restraints can be used during the whole simulated annealing protocol

  1. The concept of restraints in nursing home practice: a mixed method study in nursing homes for people with dementia.

    NARCIS (Netherlands)

    Zwijsen, S.A.; Depla, M.F.I.A.; Niemeijer, A.R.; Francke, A.L.; Hertogh, C.M.P.M.

    2011-01-01

    Introduction: Although in most developed countries the use of restraints is regulated and restricted by law, the concept of restraint in nursing home care remains ambiguous. This study aims to explore how care professionals and family members of nursing home residents with dementia in the

  2. The concurrent validity of a classification of dieters with low versus high susceptibility toward failure of restraint

    NARCIS (Netherlands)

    van Strien, T

    1997-01-01

    It has been experimentally shown that the population of high restrained eaters consists of two subpopulations, i.e., those with a low and those with a high susceptibility toward failure of restraint. Only those who combined high restraint with high scores on the disinhibition scale of the TFEQ

  3. Quality of life of nursing-home residents with dementia subject ot surveillance technology versus physical restraints: an explorative study

    NARCIS (Netherlands)

    te Boekhorst, S.; Depla, M.F.I.A.; Francke, A.L.; Twisk, J.W.R.; Zwijsen, S.A.; Hertogh, C.M.P.M.

    2013-01-01

    Objective As physical restraints should only be used in exceptional cases, there is an urgent need for alternatives to restraint use. Surveillance technology could be such an alternative. This study explored whether nursing-home residents with dementia subjected to surveillance technology had better

  4. Quality of life of nursing-home residents with dementia subject to surveillance technology versus physical restraints: an explorative study.

    NARCIS (Netherlands)

    Boekhorst, S. te; Depla, M.F.I.A.; Francke, A.L.; Twisk, J.W.R.; Zwijsen, S.A.; Hertogh, C.M.P.M.

    2013-01-01

    Objective: As physical restraints should only be used in exceptional cases, there is an urgent need for alternatives to restraint use. Surveillance technology could be such an alternative. This study explored whether nursing-home residents with dementia subjected to surveillance technology had

  5. Reducing and Eliminating Restraint of People with Developmental Disabilities and Severe Behavior Disorders: An Overview of Recent Research

    Science.gov (United States)

    Williams, Don E.

    2010-01-01

    This paper provides a brief overview of the most recent research (1999-2009) on restraint reduction and elimination efforts in the literature and also examines the characteristics of restraint along with the risks and benefits. Some earlier papers were included in this review because of their importance to the topic. The results of this literature…

  6. Educational intervention on physical restraint use in long-term care facilities - Systematic review and meta-analysis.

    Science.gov (United States)

    Lan, Shao-Huan; Lu, Li-Chin; Lan, Shou-Jen; Chen, Jong-Chen; Wu, Wen-Jun; Chang, Shen-Peng; Lin, Long-Yau

    2017-08-01

    "Physical restraint" formerly used as a measure of protection for psychiatric patients is now widely used. However, existing studies showed that physical restraint not only has inadequate effect of protection but also has negative effects on residents. To analyzes the impact of educational program on the physical restraint use in long-term care facilities. A systematic review with meta-analysis and meta-regression. Eight databases, including Cochrane Library, ProQuest, PubMed, EMBASE, EBSCO, Web of Science, Ovid Medline and Physiotherapy Evidence Database (PEDro), were searched up to January 2017. Eligible studies were classified by intervention and accessed for quality using the Quality Assessment Tool for quantitative studies. Sixteen research articles were eligible in the final review; 10 randomize control trail studies were included in the analysis. The meta-analysis revealed that the use of physical restraint was significantly less often in the experimental (education) group (OR = 0.55, 95% CI: 0.39 to 0.78, p education would have decreased the effect of the restraint educational program (β: 0.08, p = 0.002); instead, the longer education period and more times of education would have a stronger effect of reducing the use of physical restraint (β: -0.07, p educational program had an effect on the reduced use of physical restraint. The results of meta-regression suggest that long-term care facilities should provide a continuous education program of physical restraint for caregivers. Copyright © 2017. Published by Elsevier Taiwan.

  7. Exploring perspectives on restraint during medical procedures in paediatric care: a qualitative interview study with nurses and physicians.

    Science.gov (United States)

    Svendsen, Edel Jannecke; Pedersen, Reidar; Moen, Anne; Bjørk, Ida Torunn

    2017-12-01

    The aim of this study was to explore nurses' and physicians' perspectives on and reasoning about the use of restraint during medical procedures on newly admitted preschoolers in somatic hospital care. We analysed qualitative data from individual interviews with a video recall session at the end with seven physicians and eight nurses. They had earlier participated in video recorded peripheral vein cannulations on preschool children. The data were collected between May 2012 and May 2013 at a paediatric hospital unit in Norway. The analysis resulted in three main themes: (1) disparate views on the concept of restraint and restraint use (2), ways to limit the use of physical restraint and its negative consequences, and (3) experience with the role of parents and their influence on restraint. Perspectives from both healthcare professions were represented in all the main themes and had many similarities. The results of this study may facilitate more informed and reflective discussions of restraint and contribute to higher awareness of restraint in clinical practice. Lack of guidance and scientific attention to restraint combined with conflicting interests and values among healthcare providers may result in insecurity, individual dogmatism, and a lack of shared discussions, language, and terminology.

  8. Dietary restraint in college women : Fear of an imperfect fat self is stronger than hope of a perfect thin self

    NARCIS (Netherlands)

    Dalley, Simon E.; Toffanin, Paolo; Pollet, Thomas V.

    We predicted that the perceived likelihood of acquiring a hoped-for thin self would mediate perfectionistic strivings on dietary restraint, and that the perceived likelihood of acquiring a feared fat self would mediate perfectionistic concerns on dietary restraint. We also predicted that the

  9. Dietary restraint in college women: Fear of an imperfect fat self is stronger than hope of a perfect thin self

    NARCIS (Netherlands)

    Dalley, S.E.; Toffanin, P.; Pollet, T.V.

    2012-01-01

    We predicted that the perceived likelihood of acquiring a hoped-for thin self would mediate perfectionistic strivings on dietary restraint, and that the perceived likelihood of acquiring a feared fat self would mediate perfectionistic concerns on dietary restraint. We also predicted that the

  10. "A Very Fine Line": Parents' Experiences of Using Restraint with Their Adult Son/Daughter with Intellectual Disabilities

    Science.gov (United States)

    Elford, Helen; Beail, Nigel; Clarke, Zara

    2010-01-01

    Background: Restraint is sometimes used on people with intellectual disabilities who display challenging behaviours, and may be justifiable as a last resort to prevent harm. A substantial proportion of such people are cared for within the family home. The aim of this paper is to explore parents' experiences of using restraint with their…

  11. Akebia quinata Decaisne aqueous extract acts as a novel anti-fatigue agent in mice exposed to chronic restraint stress.

    Science.gov (United States)

    Park, Sun Haeng; Jang, Seol; Lee, Si Woo; Park, Sun Dong; Sung, Yoon-Young; Kim, Ho Kyoung

    2018-08-10

    Akebia quinata Decaisne extract (AQE; Lardizabalaceae) is used in traditional herbal medicine for stress- and fatigue-related depression, improvement of fatigue, and mental relaxation. To clarify the effects of AQE on stress-induced fatigue, we investigated the neuroprotective pharmacological effects of A. quinata Decaisne in mice exposed to chronic restraint stress. Seven-week old C57BL/6 mice chronically stressed by immobilization for 3 h daily for 15 d and non-stressed control mice underwent daily oral administration of AQE or distilled water. The open field, sucrose preference, and forced swimming behavioral tests were carried out once weekly, and immunohistochemical analyses of NeuN, brain-derived neurotrophic factor (BDNF), phosphorylated cAMP response element-binding (CREB) protein, and BDNF receptor tropomyosin receptor kinase B (TrkB) in striatum and hippocampus were performed at the end of the experimental period. Brain levels of serotonin, adrenaline, and noradrenaline as well as serum levels of corticosterone were measured. Behavioral tests showed that treatment with AQE improved all lethargic behaviors examined. AQE significantly attenuated the elevated levels of adrenaline, noradrenaline, and serotonin in the brain and corticosterone, alanine transaminase, and aspartate transaminase levels in the serum. Histopathological analysis showed that AQE reduced liver injury and lateral ventricle size in restraint-stress mice via inhibition of neuronal cell death. Immunohistochemical analysis showed increased phosphorylation of CREB and expression of BDNF and its receptor TrkB in striatum and hippocampus. Chlorogenic acid, isochlorogenic acid A, and isochlorogenic acid C were identified as the primary components of AQE. All three agents increased expression of BDNF in SH-SY5Y cells and PC12 cells with H 2 O 2 -induced neuronal cell damage. AQE may have a neuroprotective effect and ameliorate the effects of stress and fatigue-associated brain damage through

  12. Influence of material non-linearity on the thermo-mechanical response of polymer foam cored sandwich structures - FE modelling and preliminary experiemntal results

    DEFF Research Database (Denmark)

    Palleti, Hara Naga Krishna Teja; Thomsen, Ole Thybo; Fruehmann, Richard.K

    In this paper, the polymer foam cored sandwich structures with fibre reinforced composite face sheets will be analyzed using the commercial FE code ABAQUS/Standard® incorporating the material and geometrical non-linearity. Large deformations are allowed which attributes geometric non linearity...

  13. New scan-based test strategy for a dependable many-core processor using a NoC as a Test Access Mechanism

    NARCIS (Netherlands)

    Zhang, X.; Kerkhoff, Hans G.; Vermeulen, Bart

    2010-01-01

    Periodic on-chip scan-based tests have to be applied to a many-core processor to improve its dependability. This paper describes an infrastructural IP module that has been designed and incorporated into an SoC to function as an ATE. The Network-on-Chip inside the SoC is reused as a test access

  14. Knowledge and application of correct car seat head restraint usage among chiropractic college interns: a cross-sectional study.

    Science.gov (United States)

    Taylor, John Am; Burke, Jeanmarie; Gavencak, John; Panwar, Pervinder

    2005-03-01

    Cervical spine injuries sustained in rear-end crashes cost at least $7 billion in insurance claims annually in the United States alone. When positioned correctly, head restraint systems have been proven effective in reducing the risk of whiplash associated disorders. Chiropractors should be knowledgeable about the correct use of head restraint systems to educate their patients and thereby prevent or minimize such injuries. The primary objective of this study was to determine the prevalence of correct positioning of car seat head restraints among the interns at our institution. The secondary objective was to determine the same chiropractic interns' knowledge of the correct positioning of car seat head restraints. It was hypothesized that 100 percent of interns would have their head restraint correctly positioned within an acceptable range and that all interns would possess the knowledge to instruct patients in the correct positioning of head restraints. Cross-sectional study of a convenient sample of 30 chiropractic interns from one institution. Interns driving into the parking lot of our health center were asked to volunteer to have measurements taken and to complete a survey. Vertical and horizontal positions of the head restraint were measured using a beam compass. A survey was administered to determine knowledge of correct head restraint position. The results were recorded, entered into a spreadsheet, and analyzed. 13.3 percent of subjects knew the recommended vertical distance and only 20 percent of subjects knew the recommended horizontal distance. Chi Square analyses substantiated that the majority of subjects were unaware of guidelines set forth by the National Highway Traffic Safety Administration (NHTSA) for the correct positioning of the head restraint (chi(2) (vertical) = 16.13, chi(2) (horizontal) = 10.80, p .05). Interestingly, the 13.3 percent of the subjects who were aware of the vertical plane recommendations did not correctly position their own

  15. Seclusion and restraint in psychiatry: patients' experiences and practical suggestions on how to improve practices and use alternatives.

    Science.gov (United States)

    Kontio, Raija; Joffe, Grigori; Putkonen, Hanna; Kuosmanen, Lauri; Hane, Kimmo; Holi, Matti; Välimäki, Maritta

    2012-01-01

    This study explored psychiatric inpatients' experiences of, and their suggestions for, improvement of seclusion/restraint, and alternatives to their use in Finland. The data were collected by focused interviews (n= 30) and were analyzed with inductive content analysis. Patients' perspectives received insufficient attention during seclusion/restraint processes. Improvements (e.g., humane treatment) and alternatives (e.g., empathetic patient-staff interaction) to seclusion/restraint, as suggested by the patients, focused on essential parts of nursing practice but have not been largely adopted. Patients' basic needs have to be met, and patient-staff interaction has to also continue during seclusion/restraint. Providing patients with meaningful activities, planning beforehand, documenting the patients' wishes, and making patient-staff agreements reduce the need for restrictions and offer alternatives for seclusion/restraint. Service users must be involved in all practical development. © 2011 Wiley Periodicals, Inc.

  16. Mechanical spectral shift reactor

    International Nuclear Information System (INIS)

    Sherwood, D.G.; Wilson, J.F.; Salton, R.B.; Fensterer, H.F.

    1981-01-01

    A mechanical spectral shift reactor comprises apparatus for inserting and withdrawing water displacer elements from the reactor core for selectively changing the water-moderator volume in the core thereby changing the reactivity of the core. The apparatus includes drivemechanisms for moving the displacer elements relative to the core and guide mechanisms for guiding the displayer rods through the reactor vessel

  17. Effects of Polyethylene Grafted Maleic Anhydride on the Mechanical, Morphological, and Swelling Properties of Poly (Vinyl Chloride / Epoxidized Natural Rubber / Kenaf Core Powder Composites

    Directory of Open Access Journals (Sweden)

    Rohani Abdul Majid

    2014-10-01

    Full Text Available The effects of polyethylene grafted maleic anhydride (PE-g-MA on the properties of poly (vinyl chloride/epoxidized natural rubber (PVC/ENR kenaf core powder composites were studied, with four different loadings of kenaf core powder (5, 10, 15, and 20 phr. The tensile properties indicated that the strength and elongation at break of the composites exhibited an increase for samples with PE-g-MA. Morphological analysis using a scanning electron microscope (SEM showed better dispersion of kenaf fiber with the addition of PE-g-MA and less kenaf powder agglomeration. Furthermore, the swelling index indicated that composites with PE-g-MA showed lower toluene absorption than composites without PE-g-MA.

  18. Stellar mass spectrum within massive collapsing clumps. II. Thermodynamics and tidal forces of the first Larson core. A robust mechanism for the peak of the IMF

    Science.gov (United States)

    Lee, Yueh-Ning; Hennebelle, Patrick

    2018-04-01

    Context. Understanding the origin of the initial mass function (IMF) of stars is a major problem for the star formation process and beyond. Aim. We investigate the dependence of the peak of the IMF on the physics of the so-called first Larson core, which corresponds to the point where the dust becomes opaque to its own radiation. Methods: We performed numerical simulations of collapsing clouds of 1000 M⊙ for various gas equations of state (eos), paying great attention to the numerical resolution and convergence. The initial conditions of these numerical experiments are varied in the companion paper. We also develop analytical models that we compare to our numerical results. Results: When an isothermal eos is used, we show that the peak of the IMF shifts to lower masses with improved numerical resolution. When an adiabatic eos is employed, numerical convergence is obtained. The peak position varies with the eos, and using an analytical model to infer the mass of the first Larson core, we find that the peak position is about ten times its value. By analyzing the stability of nonlinear density fluctuations in the vicinity of a point mass and then summing over a reasonable density distribution, we find that tidal forces exert a strong stabilizing effect and likely lead to a preferential mass several times higher than that of the first Larson core. Conclusions: We propose that in a sufficiently massive and cold cloud, the peak of the IMF is determined by the thermodynamics of the high-density adiabatic gas as well as the stabilizing influence of tidal forces. The resulting characteristic mass is about ten times the mass of the first Larson core, which altogether leads to a few tenths of solar masses. Since these processes are not related to the large-scale physical conditions and to the environment, our results suggest a possible explanation for the apparent universality of the peak of the IMF.

  19. Investigation about the influence of the mechanical properties of lead core and brass jacket of a NATO 7.62 mm ball bullet in numerical simulations of ballistic impacts

    Directory of Open Access Journals (Sweden)

    Scapin M.

    2012-08-01

    Full Text Available In the present work a validated numerical approach has been used in order to build a robust and reliable FE model of the impact of a NATO 7.62 mm ball bullet, against an aluminium transmission shaft. The bullet is a full metal jacket type, with a lead alloy core and a brass jacket. Target shaft is made by an Al6061-T6 aluminium alloy. According to the soft core (lead alloy of the bullet, most effort has been spent in order to evaluate the effect of bullet materials mechanical properties on the numerical results. Numerical analyses, carried out using the non-linear dynamic finite element solver Abaqus∖Explicit 6.10, have been performed focusing on core and jacket material behaviour (target material, Al6061-T6, has been previously calibrated by the authors. Thus numerical analyses have been performed considering for the mechanical behaviour of the bullet both a simplified approach (as reported in literature and new material data (with strain rate effect obtained by means of experimental tests on the two materials (lead and brass with specimens cut directly from the bullet. Finally the results of the analyses have been compared with real experimental ballistic tests.

  20. Imidazo[1,2-c]pyrimidin-5(6H)-one as a novel core of cyclin-dependent kinase 2 inhibitors: Synthesis, activity measurement, docking, and quantum mechanical scoring.

    Science.gov (United States)

    Ajani, Haresh; Jansa, Josef; Köprülüoğlu, Cemal; Hobza, Pavel; Kryštof, Vladimír; Lyčka, Antonín; Lepsik, Martin

    2018-04-23

    We report on the synthesis, activity testing, docking, and quantum mechanical scoring of novel imidazo[1,2-c]pyrimidin-5(6H)-one scaffold for cyclin-dependent kinase 2 (CDK2) inhibition. A series of 26 compounds substituted with aromatic moieties at position 8 has been tested in in vitro enzyme assays and shown to inhibit CDK2. 2D structure-activity relationships have ascertained that small substituents at position 8 (up to the size of naphtyl or methoxyphenyl) generally lead to single-digit micromolar IC 50 values, whereas bigger substituents (substituted biphenyls) decreased the compounds' activities. The binding modes of the compounds obtained using Glide docking have exhibited up to 2 hinge-region hydrogen bonds to CDK2 and differed in the orientation of the inhibitor core and the placement of the 8-substituents. Semiempirical quantum mechanics-based scoring identified probable favourable binding modes, which will serve for future structure-based design and synthetic optimization of substituents of the heterocyclic core. In summary, we have identified a novel core for CDK2 inhibition and will explore it further to increase the potencies of the compounds and also monitor selectivities against other protein kinases. Copyright © 2018 John Wiley & Sons, Ltd.

  1. All tied up: the fine art of balancing regulatory restraint compliance and excellent patient care.

    Science.gov (United States)

    Bybel, Barbara-Ann

    2016-10-01

    This article presents examples of different resources that can be implemented to help manage a patient in crisis. It discusses challenges and solutions in regard to the ED boarding of behavioral health patients and reviews various restraint types and definitions (violent, non-violent, forensic). It stresses the importance of teamwork between security police and clinicians.

  2. [Injuries caused by traffic accidents: passive safety and restraint systems in automobiles].

    Science.gov (United States)

    Zuppichini, F; Orlandi, E; Genna, M; Rodella, L; Ricci, G; Arienzo, A; Dorrucci, V; Inaspettato, G

    1986-10-01

    In this article are considered the multiple instruments today employed in cars, in order to prevent or ameliorate the lesions caused to the occupants in case of road accident. The acquisitions in the differentiated structure of the car, in the windshield, in the components of the passenger cell are described, and the peculiar importance of the restraint systems is evidenced.

  3. Reducing Seclusion Timeout and Restraint Procedures with At-Risk Youth

    Science.gov (United States)

    Ryan, Joseph B.; Peterson, Reece; Tetreault, George; Hagen, Emily Vander

    2007-01-01

    The purpose of this pilot study was to review the effects of professional staff training in crisis management and de-escalation techniques on the use of seclusion timeout and restraint procedures with at-risk students in a K-12 special day school. An exploratory pre-post study was conducted over a two-year period, comparing the use of these…

  4. Console video games, postural activity, and motion sickness during passive restraint.

    Science.gov (United States)

    Chang, Chih-Hui; Pan, Wu-Wen; Chen, Fu-Chen; Stoffregen, Thomas A

    2013-08-01

    We examined the influence of passive restraint on postural activity and motion sickness in individuals who actively controlled a potentially nauseogenic visual motion stimulus (a driving video game). Twenty-four adults (20.09 ± 1.56 years; 167.80 ± 7.94 cm; 59.02 ± 9.18 kg) were recruited as participants. Using elastic bands, standing participants were passively restrained at the head, shoulders, hips, and knees. During restraint, participants played (i.e., controlled) a driving video game (a motorcycle race), for 50 min. During game play, we recorded the movement of the head and torso, using a magnetic tracking system. Following game play, participants answered a forced choice, yes/no question about whether they were motion sick, and were assigned to sick and well groups on this basis. In addition, before and after game play, participants completed the Simulator Sickness Questionnaire, which provided numerical ratings of the severity of individual symptoms. Five of 24 participants (20.83 %) reported motion sickness. Participants moved despite being passively restrained. Both the magnitude and the temporal dynamics of movement differed between the sick and well groups. The results show that passive restraint of the body can reduce motion sickness when the nauseogenic visual stimulus is under participants' active control and confirm that motion sickness is preceded by distinct patterns of postural activity even during passive restraint.

  5. Dietary restraint and subjective well-being in university students in Chile

    DEFF Research Database (Denmark)

    Schnettler, Berta; Horacio, Miranda; Sepúlveda, José

    2014-01-01

    with a significant variation in PD, WF, SWLS and SWFL scoring, number of days with mental health problems, frequency of alcoholic drinks consumption, restraint on the consumption of certain foods, drinks and spices, consumption frequency of fruit out of the main meals and types. Typologies did not differ...

  6. 28 CFR 552.24 - Use of four-point restraints.

    Science.gov (United States)

    2010-07-01

    ... beyond eight hours requires the supervision of qualified health personnel. Mental health and qualified... Section 552.24 Judicial Administration BUREAU OF PRISONS, DEPARTMENT OF JUSTICE INSTITUTIONAL MANAGEMENT...-point restraints, qualified health personnel shall initially assess the inmate to ensure appropriate...

  7. Use of psychotropic medication among inpatients during focused efforts in prevention of coercion and restraint

    DEFF Research Database (Denmark)

    Højlund, Mikkel; Høgh, Lene; Munk-Jørgensen, Povl

    Objective: Department of Psychiatry in Aabenraa participates in a national Danish project supporting efforts to reduce coercion and restraint in psychiatry. Antipsychotic and anxiolytic medicine is widely used among agitated patients, but is also known to contribute to cardio-vascular disease...

  8. Changing the Definition of Education. On Kant's Educational Paradox between Freedom and Restraint

    Science.gov (United States)

    Schaffar, Birgit

    2014-01-01

    Ever since Kant asked: "How am I to develop the sense of freedom in spite of the restraint?" in his lecture on education, the tension between necessary educational influence and unacceptable restriction of the child's individual development and freedom has been considered an educational paradox. Many have suggested solutions to the…

  9. Self-Injurious Behavior, Self-Restraint, and Compulsive Behaviors in Cornelia de Lange Syndrome.

    Science.gov (United States)

    Hyman, Philippa; Oliver, Chris; Hall, Scott

    2002-01-01

    Analysis of questionnaires completed by caregivers of 77 individuals with Cornelia de Lange syndrome in the United Kingdom found a significant association between self-injurious behaviors and self-restraint, and those displaying both behaviors displayed significantly more compulsions than did those not exhibiting them. Findings extend the…

  10. Pasung: Physical restraint and confinement of the mentally ill in the community

    Directory of Open Access Journals (Sweden)

    Diatri Hervita

    2008-06-01

    Full Text Available Abstract Background Physical restraint and confinement (pasung by families of people with mental illness is known to occur in many parts of the world but has attracted limited investigation. This preliminary observational study was carried out on Samosir Island in Sumatra, Indonesia, to investigate the nature of such restraint and confinement, the clinical characteristics of people restrained, and the reasons given by families and communities for applying such restraint. Methods The research method was cross-sectional observational research in a natural setting, carried out during a six-month period of working as the only psychiatrist in a remote district. Results Fifteen cases of pasung, approximately even numbers of males and females and almost all with a diagnosis of schizophrenia were identified. Duration of restraint ranged from two to 21 years. Discussion and Conclusion The provision of basic community mental health services, where there were none before, enabled the majority of the people who had been restrained to receive psychiatric treatment and to be released from pasung.

  11. Effect of honey on the reproductive system of male rat offspring exposed to prenatal restraint stress.

    Science.gov (United States)

    Haron, M N; Mohamed, M

    2016-06-01

    Exposure to prenatal stress is associated with impaired reproductive function in male rat offspring. Honey is traditionally used by the Malays for enhancement of fertility. The aim of this study was to determine the effect of honey on reproductive system of male rat offspring exposed to prenatal restraint stress. Dams were divided into four groups (n = 10/group): control, honey, stress and honey + stress groups. Dams from honey and honey + stress groups received oral honey (1.2 g kg(-1) body weight) daily from day 1 of pregnancy, meanwhile dams from stress and honey + stress groups were subjected to restraint stress (three times per day) from day 11 of pregnancy until delivery. At 10 weeks old, each male rat offspring was mated with a regular oestrus cycle female. Male sexual behaviour and reproductive performance were evaluated. Then, male rats were euthanised for assessment on reproductive parameters. Honey supplementation during prenatal restraint stress significantly increased testis and epididymis weights as well as improved the percentages of abnormal spermatozoa and sperm motility in male rat offspring. In conclusion, this study might suggest that supplementation of honey during pregnancy seems to reduce the adverse effects of restraint stress on reproductive organs weight and sperm parameters in male rat offspring. © 2015 Blackwell Verlag GmbH.

  12. The Pattern of Physical Restraints applied to the Mentally-ill in the ...

    African Journals Online (AJOL)

    Diagnostic groups found among the patients included Bipolar Affective Disorder current episode manic with psychotic symptoms (30%), Delirium (25%), Schizophrenia (20%), Acute polymorphic psychotic disorder without symptoms of schizophrenia (20%) and Dementia (5%). The reason for the use of restraints was ...

  13. Protecting children: a survey of caregivers’ knowledge of Georgia’s child restraint laws

    Directory of Open Access Journals (Sweden)

    Sheryl Strasser

    2010-11-01

    Full Text Available Sheryl Strasser1, Laurie Whorton2, Amanda J Walpole3, Sarah Beddington11Institute of Public Health, Partnership for Urban Health Research, Georgia State University, Atlanta, GA, USA; 2WellStar Corporate and Community Health, Marietta, GA, USA; 3Cobb and Douglas Public Health, Marietta, GA, USAIntroduction: The leading cause of injury and death among children in the United States is motor vehicle crashes. Even though restraint laws are in place and public awareness campaigns and educational interventions have increased, many children are still improperly restrained or not restrained at all. When correctly used, child restraints significantly reduce risk of injury or death.Methods: The purpose of the study was to elicit caregiver baseline knowledge of car seat installation and regulation before receiving car seat education from certified technicians at Inspection Station events. Inspection Station is a program whereby staff assists parents in correctly positioning car seats in participants’ vehicles. Over an 8-week period, Safe Kids Cobb County Car Seat Technicians distributed a 16-item survey, with 10 knowledge-based questions and six demographic questions to Inspection Station participants. Descriptive statistics and t-tests were conducted to assess relationships between participant age, ethnicity, and gender with overall knowledge scores. Regression analysis was run to determine the association between participant education level and total child restraint knowledge.Results: One hundred sixty-nine surveys were completed. Participant knowledge of vehicular child restraint ranged from 0% to 90% on all items. Only 29.6% of caregivers understood the proper tightness of the harness system. Less than half of the caregivers (43.8% were aware of the Georgia law requiring children aged 6 years and younger to be in some type of child restraint. Only 43.2% of caregivers surveyed knew that children need to ride in a rear-facing child restraint until 1

  14. Core BPEL

    DEFF Research Database (Denmark)

    Hallwyl, Tim; Højsgaard, Espen

    The Web Services Business Process Execution Language (WS-BPEL) is a language for expressing business process behaviour based on web services. The language is intentionally not minimal but provides a rich set of constructs, allows omission of constructs by relying on defaults, and supports language......, does not allow omissions, and does not contain ignorable elements. We do so by identifying syntactic sugar, including default values, and ignorable elements in WS-BPEL. The analysis results in a translation from the full language to the core subset. Thus, we reduce the effort needed for working...

  15. Greater physiological and behavioral effects of interrupted stress pattern compared to daily restraint stress in rats.

    Directory of Open Access Journals (Sweden)

    Wei Zhang

    Full Text Available Repeated stress can trigger a range of psychiatric disorders, including anxiety. The propensity to develop abnormal behaviors after repeated stress is related to the severity, frequency and number of stressors. However, the pattern of stress exposure may contribute to the impact of stress. In addition, the anxiogenic nature of repeated stress exposure can be moderated by the degree of coping that occurs, and can be reflected in homotypic habituation to the repeated stress. However, expectations are not clear when a pattern of stress presentation is utilized that diminishes habituation. The purpose of these experiments is to test whether interrupted stress exposure decreases homotypic habituation and leads to greater effects on anxiety-like behavior in adult male rats. We found that repeated interrupted restraint stress resulted in less overall homotypic habituation compared to repeated daily restraint stress. This was demonstrated by greater production of fecal boli and greater corticosterone response to restraint. Furthermore, interrupted restraint stress resulted in a lower body weight and greater adrenal gland weight than daily restraint stress, and greater anxiety-like behavior in the elevated plus maze. Control experiments demonstrated that these effects of the interrupted pattern could not be explained by differences in the total number of stress exposures, differences in the total number of days that the stress periods encompased, nor could it be explained as a result of only the stress exposures after an interruption from stress. These experiments demonstrate that the pattern of stress exposure is a significant determinant of the effects of repeated stress, and that interrupted stress exposure that decreases habituation can have larger effects than a greater number of daily stress exposures. Differences in the pattern of stress exposure are therefore an important factor to consider when predicting the severity of the effects of repeated

  16. Pine needle extract prevents hippocampal memory impairment in acute restraint stress mouse model.

    Science.gov (United States)

    Lee, Jin-Seok; Kim, Hyeong-Geug; Lee, Hye-Won; Kim, Won-Yong; Ahn, Yo-Chan; Son, Chang-Gue

    2017-07-31

    The Pinus densiflora leaf has been traditionally used to treat mental health disorders as a traditional Chinese medicine. Here we examined the ethnopharmacological relevance of pine needle on memory impairment caused by stress. To elucidate the possible modulatory actions of 30% ethanolic pine needle extract (PNE) on stress-induced hippocampal excitotoxicity, we adopted an acute restraint stress mouse model. Mice were orally administered with PNE (25, 50, or 100mg/kg) or ascorbic acid (100mg/kg) for 9 days, and were then subjected to restraint stress (6h/day) for 3 days (from experimental day 7-9). To evaluate spatial cognitive and memory function, the Morris water maze was performed during experimental days 5-9. Restraint stress induced the memory impairment (the prolonged escape latency and cumulative path-length, and reduced time spent in the target quadrant), and these effects were significantly prevented by PNE treatment. The levels of corticosterone and its receptor in the sera/hippocampus were increased by restraint stress, which was normalized by PNE treatment. Restraint stress elicited the hippocampal excitotoxicity, the inflammatory response and oxidative injury as demonstrated by the increased glutamate levels, altered levels of tumor necrosis factor (TNF)-α and imbalanced oxidant-antioxidant balance biomarkers. Two immunohistochemistry activities against glial fibrillary acidic protein (GFAP)-positive astrocytes and neuronal nuclei (NeuN)-positive neurons supported the finding of excitotoxicity especially in the cornu ammonis (CA)3 region of the hippocampus. Those alterations were notably attenuated by administration of PNE. The above findings showed that PNE has pharmacological properties that modulate the hippocampal excitotoxicity-derived memory impairment under severe stress conditions. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

  17. Brain-derived neurotrophic factor and hypothalamic-pituitary-adrenal axis adaptation processes in a depressive-like state induced by chronic restraint stress.

    Science.gov (United States)

    Naert, Gaelle; Ixart, Guy; Maurice, Tangui; Tapia-Arancibia, Lucia; Givalois, Laurent

    2011-01-01

    Depression is potentially life-threatening. The most important neuroendocrine abnormality in this disorder is hypothalamo-pituitary-adrenocortical (HPA) axis hyperactivity. Recent findings suggest that all depression treatments may boost the neurotrophin production especially brain-derived neurotrophic factor (BDNF). Moreover, BDNF is highly involved in the regulation of HPA axis activity. The aim of this study was to determine the impact of chronic stress (restraint 3h/day for 3 weeks) on animal behavior and HPA axis activity in parallel with hippocampus, hypothalamus and pituitary BDNF levels. Chronic stress induced changes in anxiety (light/dark box test) and anhedonic states (sucrose preference test) and in depressive-like behavior (forced swimming test); general locomotor activity and body temperature were modified and animal body weight gain was reduced by 17%. HPA axis activity was highly modified by chronic stress, since basal levels of mRNA and peptide hypothalamic contents in CRH and AVP and plasma concentrations in ACTH and corticosterone were significantly increased. The HPA axis response to novel acute stress was also modified in chronically stressed rats, suggesting adaptive mechanisms. Basal BDNF contents were increased in the hippocampus, hypothalamus and pituitary in chronically stressed rats and the BDNF response to novel acute stress was also modified. This multiparametric study showed that chronic restraint stress induced a depressive-like state that was sustained by mechanisms associated with BDNF regulation. Copyright © 2010 Elsevier Inc. All rights reserved.

  18. Mechanics

    CERN Document Server

    Chester, W

    1979-01-01

    When I began to write this book, I originally had in mind the needs of university students in their first year. May aim was to keep the mathematics simple. No advanced techniques are used and there are no complicated applications. The emphasis is on an understanding of the basic ideas and problems which require expertise but do not contribute to this understanding are not discussed. How­ ever, the presentation is more sophisticated than might be considered appropri­ ate for someone with no previous knowledge of the subject so that, although it is developed from the beginning, some previous acquaintance with the elements of the subject would be an advantage. In addition, some familiarity with element­ ary calculus is assumed but not with the elementary theory of differential equations, although knowledge of the latter would again be an advantage. It is my opinion that mechanics is best introduced through the motion of a particle, with rigid body problems left until the subject is more fully developed. Howev...

  19. Detailed comparison between computed and measured FBR core seismic responses

    International Nuclear Information System (INIS)

    Forni, M.; Martelli, A.; Melloni, R.; Bonacina, G.

    1988-01-01

    This paper presents a detailed comparison between seismic calculations and measurements performed for various mock-ups consisting of groups of seven and nineteen simplified elements of the Italian PEC fast reactor core. Experimental tests had been performed on shaking tables in air and water (simulating sodium) with excitations increasing up to above Safe Shutdown Earthquake. The PEC core-restraint ring had been simulated in some tests. All the experimental tests have been analysed by use of both the one-dimensional computer program CORALIE and the two-dimensional program CLASH. Comparisons have been made for all the instrumented elements, in both the time and the frequency domains. The good agreement between calculations and measurements has confirmed adequacy of the fluid-structure interaction model used for PEC core seismic design verification

  20. Mechanical properties of API X80 steel pipe joints welded by Flux Core Arc Weld Process; Propriedades mecanicas de juntas de tubos de aco API X80 soldadas com arame tubulares

    Energy Technology Data Exchange (ETDEWEB)

    Ordonez, Robert E. Cooper; Silva, Jose Hilton F.; Trevisan, Roseana E. [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Mecanica. Dept. de Engenharia de Fabricacao

    2003-07-01

    Flux Core Arc Welding processes (FCAW) are beginning to be applied in pipeline welds, however, very limited experimental data regarding mechanical properties of pipeline weld joints with these processes are available in the literature. In this paper, the effects of preheat temperature and type of FCAW on mechanical properties (microhardness and tensile strength) of API X80 weld joint steel are presented. FCAW processes with gas protection and self-shielded were used. Multipasses welding were applied in 30'' diameter and 0,625'' thickness tubes. Influence factors were: FCAW type and preheat temperature. Acceptance criteria of welded joints were evaluated by API 1104 standard for tensile strength test and ASTM E384-99 for microhardness test. The results obtained showed that FCAW type and preheat temperature have no influence on mechanical properties of API X80 joint steel. (author)

  1. Quality of life of nursing-home residents with dementia subject to surveillance technology versus physical restraints: an explorative study.

    Science.gov (United States)

    Te Boekhorst, S; Depla, M F I A; Francke, A L; Twisk, J W R; Zwijsen, S A; Hertogh, C M P M

    2013-04-01

    As physical restraints should only be used in exceptional cases, there is an urgent need for alternatives to restraint use. Surveillance technology could be such an alternative. This study explored whether nursing-home residents with dementia subjected to surveillance technology had better quality of life scores for mood, behavioral and societal dimensions than residents with physical restraints. Quality of life was assessed longitudinally, with three measurements in six psychogeriatric nursing homes of residents with surveillance technology (n = 170) and residents with physical restraints (n = 22). QUALIDEM subscales were used to measure five dimensions of quality of life. Multilevel longitudinal univariate and multivariate regression techniques were used to analyze the data. Because physical restraints were almost exclusively used in residents with low activities of daily living (ADL) independency (18 of the 22), we restricted the regression analyses to residents with a Barthel Index score ≤ 5 (overall n = 53). Univariate results showed that highly ADL-dependent residents with surveillance technology had significantly more positive affect than highly ADL-dependent residents with physical restraints. However, this difference proved to be no longer significant after adjustment for the confounders: age, sex and stage of dementia. Quality of life of highly ADL-dependent nursing-home residents with dementia seems to be unrelated to the use of surveillance technology as opposed to physical restraints. Copyright © 2012 John Wiley & Sons, Ltd.

  2. Contributions of mindful eating, intuitive eating, and restraint to BMI, disordered eating, and meal consumption in college students.

    Science.gov (United States)

    Anderson, Lisa M; Reilly, Erin E; Schaumberg, Katherine; Dmochowski, Sasha; Anderson, Drew A

    2016-03-01

    Mindful eating and intuitive eating are promoted as means to circumvent potentially maladaptive dietary restraint while maintaining a healthy weight. Although theoretically related, no studies have examined the correlations between intuitive eating, mindful eating, and restraint in the same sample. This study sought to examine these constructs and their correlations with body mass index (BMI), eating-disordered behaviors, and meal consumption in a college sample. Participants (N = 125) completed a laboratory taste-test meal and measures of each eating-related construct using the EDDS, IES, MEQ, and TFEQ-Restraint Subscale. Mindful eating, intuitive eating, and restraint were not strongly correlated. Hierarchical multiple regression analyses indicated that restraint and intuitive eating accounted for significant variance in disordered eating and BMI. Elevated restraint was associated with increased BMI and disordered eating; elevated intuitive eating was associated with decreased BMI and disordered eating. Mindful eating did not correlate with any outcome variables. Follow-up analyses suggested that specific intuitive eating subscales accounted for unique variance in the relation between intuitive eating and disordered eating. Intuitive eating was the only construct that was significantly associated with meal consumption. Intuitive eating and restraint appear to be only weakly correlated, and each is differentially associated with meal consumption. Mindful eating does not appear to relate to outcome variables.

  3. Core sequence of PAPf39 amyloid fibrils and mechanism of pH-dependent fibril formation: the role of monomer conformation.

    Science.gov (United States)

    French, Kinsley C; Makhatadze, George I

    2012-12-21

    PAPf39, a 39-residue peptide fragment from human prostatic acidic phosphatase, has been shown to form amyloid fibrils in semen (SEVI), which increase HIV infectivity by up to 5 orders of magnitude. The sequence of the PAPf39 fibrillar core was identified using hydrogen-deuterium exchange (HDX) mass spectrometry and protease protection assays. The central and C-terminal regions are highly protected from HDX and proteolytic cleavage and, thus, are part of the fibrillar core. Conversely, the N-terminal region is unprotected from HDX and proteolytic cleavage, suggesting that it is exposed and not part of the fibrillar core. This finding was tested using two N-terminal truncated variants, PAPf39Δ1-8 and PAPf39Δ1-13. Both variants formed amyloid fibrils at neutral pH. However, these variants showed a markedly different pH dependence of fibril formation versus that of PAPf39. PAPf39 fibrils can form at pH 7.7, but not at pH 5.5 or 2.5, while both N-terminally truncated variants can form fibrils at these pH values. Thus, the N-terminal region is not necessary for fibril formation but modulates the pH dependence of PAPf39 fibril formation. PAPf39Δ1-8 and PAPf39Δ1-13 are capable of seeding PAPf39 fibril formation at neutral pH, suggesting that these variants are structurally compatible with PAPf39, yet no mixed fibril formation occurs between the truncated variants and PAPf39 at low pH. This suggests that pH affects the PAPf39 monomer conformational ensemble, which is supported by far-UV circular dichroism spectroscopy. A conceptual model describing the pH dependence of PAPf39 aggregation is proposed and provides potential biological implications.

  4. Child restraint use in low socio-economic areas of urban Sydney during transition to new legislation.

    Science.gov (United States)

    Keay, Lisa; Hunter, Kate; Brown, Julie; Bilston, Lynne E; Simpson, Judy M; Stevenson, Mark; Ivers, Rebecca Q

    2013-01-01

    Child restraints protect a young child against injury in crashes but best practice child restraint use is low in Australia, particularly among lower socio-economic groups. We investigated factors associated with restraint use to inform the development of education and distribution programmes to support new Australian legislation on child passengers among families in low socio-economic areas of metropolitan Sydney. We interviewed a parent or carer of 1160 children aged 2-5 years enrolled at one of 28 early childhood centres in low socio-economic areas of urban Sydney. Appropriate child restraint use was defined as a forward facing child restraint (FFCR) for 2-3 year olds and a FFCR or booster seat for children aged 4 years or more. Predictors of self-reported appropriate use were explored using logistic regression. Analysis was conducted on one child from each family in the target age range (2-5 years): 586 (51%) were male and the mean age was 3.5 (Standard Deviation 0.8) years. There were 432 (45%) families with annual income below $60,000, 248 (22%) spoke a language other than English at home and 360 (33%) had 3 or more children. Fifty-four percent of carers indicated that their 2-3 year old children travelled in a FFCR. Inappropriate use among children in this age group was more likely when the carer was law and poorer knowledge of safety benefits of child restraints. They also had lower household incomes and more concerns about cost of child restraints and booster seats. These findings can inform development of interventions to promote best practice child restraint use, which will reach non-English speaking families in this region. They also confirm the importance of economic and logistic barriers to best practice child restraint use. Copyright © 2012 Elsevier Ltd. All rights reserved.

  5. [Land layout for lake tourism based on ecological restraint].

    Science.gov (United States)

    Wang, Jian-Ying; Li, Jiang-Feng; Zou, Li-Lin; Liu, Shi-Bin

    2012-10-01

    To avoid the decrease and deterioration of lake wetlands and the other ecological issues such as lake water pollution that were caused by the unreasonable exploration of lake tourism, a land layout for the tourism development of Liangzi Lake with the priority of ecological security pattern was proposed, based on the minimal cumulative resistance model and by using GIS technology. The study area was divided into four ecological function zones, i. e., core protection zone, ecological buffer zone, ecotone zone, and human activity zone. The core protection zone was the landscape region of ecological source. In the protection zone, new tourism land was forbidden to be increased, and some of the existing fundamental tourism facilities should be removed while some of them should be upgraded. The ecological buffer zone was the landscape region with resistance value ranged from 0 to 4562. In the buffer zone, expansion of tourism land should be forbidden, the existing tourism land should be downsized, and human activities should be isolated from ecological source by converting the human environment to the natural environment as far as possible. The ecotone zone was the landscape region with resistance value ranged from 4562 to 30797. In this zone, the existing tourism land was distributed in patches, tourism land could be expanded properly, and the lake forestry ecological tourism should be developed widely. The human activity zone was the landscape region with resistance value ranged from 30797 to 97334, which would be the key area for the land layout of lake tourism. It was suggested that the land layout for tourism with the priority of landscape ecological security pattern would be the best choice for the lake sustainable development.

  6. Influence of drying restraint on physical and mechanical properties of nanofibrillated cellulose films

    Science.gov (United States)

    Carlos Baez; John Considine; Robert Rowlands

    2014-01-01

    Nanofibrillated cellulose (NFC) is a renewable and biodegradable fibril that possesses high strength and stiffness resulting from high level hydrogen bonding. Films made from NFC shrink and distort as they transition from a wet state (20 wt% solids) to a state of moisture equilibrium (90 wt% solids at 50 % RH, 23 °C). Material distortions are driven by development of...

  7. Hydro-mechanical properties of pressure core sediments recovered from the Krishna-Godavari Basin during India's National Gas Hydrate Program Expedition NGHP-02

    Science.gov (United States)

    Yoneda, J.; Oshima, M.; Kida, M.; Kato, A.; Konno, Y.; Jin, Y.; Waite, W. F.; Jang, J.; Kumar, P.; Tenma, N.

    2017-12-01

    Pressure coring and analysis technology allows for gas hydrate to be recovered from the deep seabed, transferred to the laboratory and characterized while continuously maintaining gas hydrate stability. For this study, dozens of hydrate-bearing pressure core sediment subsections recovered from the Krishna-Godavari Basin during India's National Gas Hydrate Program Expedition NGHP-02 were tested with Pressure Core Non-destructive Analysis Tools (PNATs) through a collaboration between Japan and India. PNATs, originally developed by AIST as a part of the Japanese National hydrate research program (MH21, funded by METI) conducted permeability, compression and consolidation tests under various effective stress conditions, including the in situ stress state estimated from downhole bulk density measurements. At the in situ effective stress, gas hydrate-bearing sediments had an effective permeability range of 0.01-10mD even at pore-space hydrate saturations above 60%. Permeability increased by 10 to 100 times after hydrate dissociation at the same effective stress, but these post-dissociation gains were erased when effective stress was increased from in situ values ( 1 MPa) to 10MPa in a simulation of the depressurization method for methane extraction from hydrate. Vertical-to-horizontal permeability anisotropy was also investigated. First-ever multi-stage loading tests and strain-rate alternation compression tests were successfully conducted for evaluating sediment strengthening dependence on the rate and magnitude of effective confining stress changes. In addition, oedometer tests were performed up to 40MPa of consolidation stress to simulate the depressurization method in ultra-deep sea environments. Consolidation curves measured with and without gas hydrate were investigated over a wide range of effective confining stresses. Compression curves for gas hydrate-bearing sediments were convex downward due to high hydrate saturations. Consolidation tests show that

  8. Au@NiO core-shell nanoparticles as a p-type gas sensor: Novel synthesis, characterization, and their gas sensing properties with sensing mechanism

    KAUST Repository

    Majhi, Sanjit Manohar

    2018-04-25

    In this work, Au@NiO core-shell nanoparticles (C-S NPs) as a p-type gas sensing material was synthesized by a facile wet-chemical method, and evaluated their gas sensing properties as compared to the pristine NiO NPs gas sensors. Transmission electron microscope (TEM) results exhibited the well-dispersed formation of Au@NiO C-S NPs having the total size of 70–120 nm and NiO shells having 30–50 nm thickness. The C-S morphology as well as the overall particle sizes are unchanged even at 500 °C. The gas sensing result reveals that the response of Au@NiO C-S NPs gas sensor is higher than pristine NiO NPs gas sensor for 100 ppm of ethanol at 200 °C operating temperature. The baseline resistance in the air for Au@NiO C-S NPs sensor is lowered as compared to pristine NiO NPs, which is due to the increased number of holes as charge carriers in Au@NiO C-S NPs. The high response of Au@NiO core-shell NPs as compared to pristine NiO NPs is attributed to electronic and chemical sensitization effects of Au. In Au@NiO C-S structure, the contact between metal (Au) and semiconductor (NiO) formed a Schottky junction since Au metal acted as electron acceptor, a withdrawal of electrons from NiO by Au metal core leaved behind number of holes as charge carriers in Au@NiO C-S NPs. Therefore, the baseline resistance of Au@NiO C-S NPs greatly decreased than pristine NiO NPs, as a result the Au@NiO C-S NPs showed higher response. On the other hand, in chemical sensitization effect, Au NPs catalyzed to dissociate O2 molecules into ionic species. This work will give some clue to the researchers for the further development of p-type based C-S NPs sensors.

  9. Belt restraint reduction in nursing homes: design of a quasi-experimental study

    Directory of Open Access Journals (Sweden)

    van Rossum Erik

    2010-02-01

    Full Text Available Abstract Background The use of physical restraints still is common practice in the nursing home care. Since physical restraints have been shown to be an ineffective and sometimes even hazardous measure, interventions are needed to reduce their usage. Several attempts have been made to reduce the use of physical restraints. Most studies used educational approaches and introduced a nurse specialist as a consultant. However, the success rate of these interventions has been inconsistent. We developed a new multi-component intervention (EXBELT comprising an educational intervention for nursing home staff in combination with a policy change (belt use is prohibited by the nursing home management, availability of a nurse specialist and nursing home manager as consultants, and availability of alternative interventions. The first aim of this study is to further develop and test the effectiveness of EXBELT on belt restraint reduction in Dutch psychogeriatric nursing homes. However, the reduction of belts should not result in an increase of other restrictive restraints (such as a chair with locked tray table or psychoactive drug use. The overall aim is an effective and feasible intervention that can be employed on a large scale in Dutch nursing homes. Methods and design Effects of EXBELT will be studied in a quasi-experimental longitudinal study design. Alongside the effect evaluation, a process evaluation will be carried out in order to further develop EXBELT. Data regarding age, gender, use of physical restraints, the number of falls and fall related injuries, psychoactive drug use, and the use of alternative interventions will be collected at baseline and after four and eight months of follow-up. Data regarding the process evaluation will be gathered in a period of eight months between baseline and the last measurement. Furthermore, changing attitudes will become an important addition to the educational part of EXBELT. Discussion A quasi

  10. Discordance between age- and size-based criteria of child passenger restraint appropriateness.

    Science.gov (United States)

    Smiley, Mary L; Bingham, C Raymond; Jacobson, Peter D; Macy, Michelle L

    2018-04-03

    In this study, we sought to accomplish the following objectives: to (1) calculate the percentage of children considered appropriately restrained across 8 criteria of increasing restrictiveness; (2) examine agreement between age- and size-based appropriateness criteria; (3) assess for changes in the percentage of children considered appropriately restrained by the 8 criteria between 2011 (shortly after updates to U.S. guidelines) and 2015. Data from 2 cross-sectional surveys of 928 parents of children younger than 12 years old (n = 591 in 2011, n = 337 in 2015) were analyzed in 2017. Child age, weight, and height were measured at an emergency department visit and used to determine whether the parent-reported child passenger restraint was considered appropriate according to 8 criteria. Age-based criteria were derived from Michigan law and U.S. Weight, height, and size-based criteria were derived from typical restraints available in the United States in 2007 and 2011. The percentage appropriate restraint use was calculated for each criterion. The kappa statistic was used to measure agreement between criteria. Change in appropriateness from 2011 to 2015 was assessed with chi-square statistics. Percentage appropriate restraint use varied from a low of 19% for higher weight limits in 2011 to a high of 91% for Michigan law in 2015. Agreement between criteria was slight to moderate. The lowest kappa was for Michigan law and higher weight limits in 2011 (κ = 0.06) and highest for U.S. guidelines and lower weight limits in 2011 (κ = 0.60). Percentage appropriate restraint use was higher in 2015 than 2011 for the following criteria: U.S. guidelines (74 vs. 58%, P consistency in reporting results from studies of child passenger safety in the United States. Potential explanations for the increased percentage of children considered appropriately restrained between 2011 and 2015 include adoption of the updated U.S. guidelines and the use of child passenger restraints with

  11. WHIPJET progress on piping restraint elimination at Beaver Valley - 2

    International Nuclear Information System (INIS)

    Server, W.L.; Szy Slow Ski, J.J.; Goldstein, N.A.

    1986-01-01

    Fracture mechanics technology has advanced to the point that an engineering approach using the concept of leak-before-break in lieu of postulating double-ended pipe rupture is now possible. An approach based upon this fracture mechanics technology, termed WHIPJET, is currently being applied to Beaver Valley Power Station, Unit 2 for Duquesne Light Company. The WHIPJET philosophy is simple, conservative, and provides defense-in-depth arguments for high energy piping throughout the balance-of-plant. Progress being made in applying WHIPJET to several lines is presented

  12. Analysis of the seismic response of a fast reactor core

    International Nuclear Information System (INIS)

    Martelli, A.; Maresca, G.

    1984-01-01

    This report deals with the methods to apply for a correct evaluation of the reactor core seismic response. Reference is made to up-to-date design data concerning the PEC core, taking into account the presence of the core-restraint plate located close to the PEC core elements top and applying the optimized iterative procedure between the vessel linear calculation and the non-linear ones limited to the core, which had been described in a previous report. It is demonstrated that the convergence of this procedure is very fast, similar to what obtained in the calculations of the cited report, carried out with preliminary data, and it is shown that the cited methods allow a reliable evaluation of the excitation time histories for the experimental tests in support of the seismic verification of the shutdown system and the core of a fast reactor, as well as relevant data for the experimental, structural and functional, verification of the core elements in the case of seismic loads

  13. Assessing competence of broccoli consumption on inflammatory and antioxidant pathways in restraint-induced models: estimation in rat hippocampus and prefrontal cortex.

    Science.gov (United States)

    Khalaj, Leila; Nejad, Sara Chavoshi; Mohammadi, Marzieh; Sarraf Zadeh, Sadaf; Pour, Marieh Hossein; Ashabi, Ghorbangol; Khodagholi, Fariba; Ahmadiani, Abolhassan

    2013-01-01

    A growing body of evidence advocated the protective and therapeutic potential of natural compounds and phytochemicals used in diets against pathological conditions. Herein, the outcome of dietary whole broccoli consumption prior to restraint stress has been investigated in the hippocampus and prefrontal cortex of male rats, two important regions involved in the processing of responses to stressful events. Interestingly, a region-specific effect was detected regarding some of antioxidant defense system factors: nuclear factor erythroid-derived 2-related factor 2 (Nrf-2) antioxidant pathway, mitochondrial prosurvival proteins involved in mitochondrial biogenesis, and apoptotic cell death proteins. Dietary broccoli supplementation modulated the restraint-induced changes towards a consistent overall protection in the hippocampus. In the prefrontal cortex, however, despite activation of most of the protective factors, presumably as an attempt to save the system against the stress insult, some detrimental outcomes such as induced malate dehydrogenase (MDA) level and cleaved form of caspase-3 were detectable. Such diversity may be attributed in one hand to the different basic levels and/or availability of defensive mechanisms within the two studied cerebral regions, and on the other hand to the probable dose-dependent and hormetic effects of whole broccoli. More experiments are essential to demonstrate these assumptions.

  14. Assessing Competence of Broccoli Consumption on Inflammatory and Antioxidant Pathways in Restraint-Induced Models: Estimation in Rat Hippocampus and Prefrontal Cortex

    Directory of Open Access Journals (Sweden)

    Leila Khalaj

    2013-01-01

    Full Text Available A growing body of evidence advocated the protective and therapeutic potential of natural compounds and phytochemicals used in diets against pathological conditions. Herein, the outcome of dietary whole broccoli consumption prior to restraint stress has been investigated in the hippocampus and prefrontal cortex of male rats, two important regions involved in the processing of responses to stressful events. Interestingly, a region-specific effect was detected regarding some of antioxidant defense system factors: nuclear factor erythroid-derived 2-related factor 2 (Nrf-2 antioxidant pathway, mitochondrial prosurvival proteins involved in mitochondrial biogenesis, and apoptotic cell death proteins. Dietary broccoli supplementation modulated the restraint-induced changes towards a consistent overall protection in the hippocampus. In the prefrontal cortex, however, despite activation of most of the protective factors, presumably as an attempt to save the system against the stress insult, some detrimental outcomes such as induced malate dehydrogenase (MDA level and cleaved form of caspase-3 were detectable. Such diversity may be attributed in one hand to the different basic levels and/or availability of defensive mechanisms within the two studied cerebral regions, and on the other hand to the probable dose-dependent and hormetic effects of whole broccoli. More experiments are essential to demonstrate these assumptions.

  15. Did Child Restraint Laws Globally Converge? Examining 40 Years of Policy Diffusion.

    Science.gov (United States)

    Nazif-Muñoz, José Ignacio

    2015-01-01

    The objective of the current study is to determine what factors have been associated with the global adoption of mandatory child restraint laws (ChRLs) since 1975. In order to determine what factors explained the global adoption of mandatory ChRLs, Weibull models were analyzed. To carry out this analysis, 170 countries were considered and the time risk corresponded to 5,146 observations for the period 1957-2013. The dependent variable was first time to adopt a ChRL. Independent variables representing global factors were the World Health Organization (WHO) and World Bank's (WB) road safety global campaign; the Geneva Convention on Road Traffic; and the United Nation's (UN) 1958 Vehicle Agreement. Independent variables representing regional factors were the creation of the European Transport Safety Council and being a Commonwealth country. Independent variables representing national factors were population; gross domestic product (GDP) per capita; political violence; existence of road safety nongovernmental organizations (NGOs); and existence of road safety agencies. Urbanization served as a control variable. To examine regional dynamics, Weibull models for Africa, Asia, Europe, North America, Latin America, the Caribbean, and the Commonwealth were also carried out. Empirical estimates from full Weibull models suggest that 2 global factors and 2 national factors are significantly associated with the adoption of this measure. The global factors explaining adoption are the WHO and WB's road safety global campaign implemented after 2004 (P policy was global. Regional analysis showed that the UN's Convention on Road Traffic was significant in Asia, the creation of the European Transport Safety Council was significant in Europe and North America, and the global campaign was in Africa. In Commonwealth and European and North American countries, the existence of road safety agencies was also positively associated with ChRL adoption. Results of the world models suggest that

  16. Interactive effects of dietary restraint and adiposity on stress-induced eating and the food choice of children

    Science.gov (United States)

    The Individual Differences Model posits that individual differences in physiological and psychological factors explain eating behaviors in response to stress. The purpose was to determine the effects of individual differences in adiposity, dietary restraint and stress reactivity on children's energy...

  17. Surveillance technology: an alternative to physical restraints? A qualitative study among professionals working in nursing homes for people with dementia.

    NARCIS (Netherlands)

    Zwijsen, S.A.; Depla, M.F.I.A.; Niemeijer, A.R.; Francke, A.L.; Hertogh, C.M.P.M.

    2012-01-01

    Background: Working with surveillance technology as an alternative to traditional restraints creates obvious differences in the way care is organised. It is not clear whether professional caregivers find working with surveillance technology useful and workable and whether surveillance technology is

  18. Dieting in Moderation: The Role of Dietary Restraint in the Relationship between Body Dissatisfaction and Psychological Well-being.

    Science.gov (United States)

    Tiggemann, M

    1997-10-01

    This study demonstrates the substantial conceptual consequences in distinguishing a variable's role as a moderator as opposed to a mediator. In particular, the study investigates the role of dietary restraint in the relationship between body dissatisfaction and psychological well-being. Path analyses showed that, in addition to its mediating role, dietary restraint has a moderating role, such that there is a stronger relationship between body dissatisfaction and psychological well-being when dietary restraint is high than when dietary restraint is low. In contrast, gender had only a direct effect on weight dissatisfaction. It was concluded that the same processes occur for both men and for women, whereby it is the individuals who diet who suffer loss of psychological well-being.

  19. A network approach to response inhibition: dissociating functional connectivity of neural components involved in action restraint and action cancellation

    NARCIS (Netherlands)

    Dambacher, F.; Sack, A.T.; Lobbestael, J.; Arntz, A.; Brugman, S.; Schuhmann, T.

    2014-01-01

    The ability to inhibit action tendencies is vital for adaptive human behaviour. Various paradigms are supposed to assess action inhibition and are often used interchangeably. However, these paradigms are based on different conceptualizations (action restraint vs. action cancellation) and the

  20. Enhancing the humidity sensitivity of Ga2O3 /SnO2 core/shell microribbon by applying mechanical strain and its application as a flexible strain sensor.

    Science.gov (United States)

    Liu, Kewei; Sakurai, Makoto; Aono, Masakazu

    2012-12-07

    The humidity sensitivity of a single β-Ga(2) O(3) /amorphous SnO(2) core/shell microribbon on a flexible substrate is enhanced by the application of tensile strain and increases linearly with the strain. The strain-induced enhancement originates from the increase in the effective surface area where water molecules are adsorbed. This strain dependence of humidity sensitivity can be used to monitor the external strain. The strain sensing of the microribbon device under various amounts of mechanical loading shows excellent reliability and reproducibility with a gauge factor of -41. The flexible device has high potential to detect both humidity and strain at room temperature. These findings and the mechanism involved are expected to pave the way for new flexible strain and multifunctional sensors. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Investigating core genetic-and-epigenetic cell cycle networks for stemness and carcinogenic mechanisms, and cancer drug design using big database mining and genome-wide next-generation sequencing data.

    Science.gov (United States)

    Li, Cheng-Wei; Chen, Bor-Sen

    2016-10-01

    Recent studies have demonstrated that cell cycle plays a central role in development and carcinogenesis. Thus, the use of big databases and genome-wide high-throughput data to unravel the genetic and epigenetic mechanisms underlying cell cycle progression in stem cells and cancer cells is a matter of considerable interest. Real genetic-and-epigenetic cell cycle networks (GECNs) of embryonic stem cells (ESCs) and HeLa cancer cells were constructed by applying system modeling, system identification, and big database mining to genome-wide next-generation sequencing data. Real GECNs were then reduced to core GECNs of HeLa cells and ESCs by applying principal genome-wide network projection. In this study, we investigated potential carcinogenic and stemness mechanisms for systems cancer drug design by identifying common core and specific GECNs between HeLa cells and ESCs. Integrating drug database information with the specific GECNs of HeLa cells could lead to identification of multiple drugs for cervical cancer treatment with minimal side-effects on the genes in the common core. We found that dysregulation of miR-29C, miR-34A, miR-98, and miR-215; and methylation of ANKRD1, ARID5B, CDCA2, PIF1, STAMBPL1, TROAP, ZNF165, and HIST1H2AJ in HeLa cells could result in cell proliferation and anti-apoptosis through NFκB, TGF-β, and PI3K pathways. We also identified 3 drugs, methotrexate, quercetin, and mimosine, which repressed the activated cell cycle genes, ARID5B, STK17B, and CCL2, in HeLa cells with minimal side-effects.

  2. Determination of protein global folds using backbone residual dipolar coupling and long-range NOE restraints

    International Nuclear Information System (INIS)

    Giesen, Alexander W.; Homans, Steve W.; Brown, Jonathan Miles

    2003-01-01

    We report the determination of the global fold of human ubiquitin using protein backbone NMR residual dipolar coupling and long-range nuclear Overhauser effect (NOE) data as conformational restraints. Specifically, by use of a maximum of three backbone residual dipolar couplings per residue (N i -H N i , N i -C' i-1 , H N i - C' i-1 ) in two tensor frames and only backbone H N -H N NOEs, a global fold of ubiquitin can be derived with a backbone root-mean-square deviation of 1.4 A with respect to the crystal structure. This degree of accuracy is more than adequate for use in databases of structural motifs, and suggests a general approach for the determination of protein global folds using conformational restraints derived only from backbone atoms

  3. Allometric scaling of chemical restraint associated with inhalant anesthesia in giant anteaters.

    Science.gov (United States)

    Carregaro, Adriano Bonfim; Gerardi, Patrícia Molina; Honsho, Daniel Kan

    2009-04-01

    This study describes the use of allometric scaling in five giant anteaters (Myrmecophaga tridactyla) submitted for osteosynthesis, gastrostomy, or treatment of burns. Chemical restraint was performed by allometric scaling using the dog as a reference; acepromazine (0.06 mg/kg), diazepam (0.3 mg/kg), ketamine (8.8 mg/kg), and buprenorphine (5.9 microg/kg) were combined, and the animals were maintained under isoflurane anesthesia. Heart rate, respiratory rate, hemoglobin oxygen saturation, temperature, and anesthetic depth were measured. Postoperative treatment consisted of ketoprofen, buprenorphine, and ceftiofur. Anesthetic induction was obtained in 10-15 min, achieving muscle relaxation and absence of excitement. Physiologic parameters were stable during the procedures, and postoperative treatment was effective. Allometric scaling was effective for chemical restraint and postoperative treatment.

  4. A smart base restraint for wind turbines to mitigate undesired effects due to structural vibrations

    DEFF Research Database (Denmark)

    Caterino, N.; Georgakis, Christos T.; Spizzuoco, M.

    2016-01-01

    Concerns in the last decades of the negative impact of the use of fossil fuels on the environment has lead to a boom in the production of wind turbines. To take advantage of the smoother stronger winds at height, wind turbine heights are progressively increasing. This has led to an increased demand...... to control tower forces. The application of a semi-active (SA) control system is herein proposed and discussed. Its aim is to limit bending moment demand at the base of a wind turbine by relaxing the base restraint of the turbine's tower, without increasing the top displacement. This is done thanks....... This smart restraint is made of a central smooth hinge, elastic springs and SA magnetorheological dampers driven by a control algorithm properly designed for the specific application. A commercial 105 m tall wind turbine has been assumed as a case study. Several numerical simulations have been performed...

  5. [Use of restraint in psychiatry: Feelings of caregivers and ethical perspectives].

    Science.gov (United States)

    Guivarch, J; Cano, N

    2013-09-01

    The return of restraint in psychiatry raises many ethical issues for caregivers. However their experience is little explored in literature. Our objective was to study the feelings of caregivers facing restraint with regard to an ethical perspective and to identify areas for improvement. Between November 2011 and February 2012 a descriptive cross-sectional epidemiological study was performed in two psychiatric emergency services and two closed units in which doctors and nurses were individually interviewed using semi-structured questionnaires. Five topics were explored: indications and contexts, impact on the patient, caregiver-patient relationship, perspective on the practice and feelings of caregivers on which we insist particularly. Results were presented in tables with percentages and possibly diagrams. The notable responses of caregivers were also cited. Twenty nurses and nine psychiatrists, mostly female, were recruited. They all had participated in experiments of restraint. The self-aggressiveness, the aggressiveness against other persons and agitation were the most frequent indications. In the patients, caregivers identified misunderstanding (79.3%) and anger (75.9%). The majority of nurses (75%) felt that there was an improvement in the caregiver-patient relationship after the episode of restraint compared to what it had been in the moments preceding this measure. The emotional experience of caregivers was rich, intense and predominantly negative type of frustration (35% of nurses; 66.7% of doctors), anger (30 and 33.3%) and lack of feeling (35 and 44.4%). The feelings of doctors and nurses were not completely similar. For caregivers it was "a difficult but necessary experience" (82.75%), "an act of care and safety" (68.9%). All psychiatrists and almost half of the nurses (45%) said they did not feel the same when they used seclusion. In their opinion, seclusion entailed a less painful experience because of its therapeutic properties. More than half of the

  6. Mediation of Weight Loss and Weight Loss Maintenance through Dietary Disinhibition and Restraint.

    Science.gov (United States)

    JaKa, Meghan M; Sherwood, Nancy E; Flatt, Shirley W; Pacanowski, Carly R; Pakiz, Bilgé; Thomson, Cynthia A; Rock, Cheryl L

    2015-04-01

    Understanding the degree to which eating behaviors, such as disinhibition and restraint, are associated with weight loss and weight loss maintenance could contribute to further refinement of effective weight management intervention strategies. The purpose of this analysis was to examine if these factors mediate weight loss or weight loss maintenance using data from a randomized controlled trial testing a commercial weight loss program that delivered behavioral counseling and structured meal plans including prepackaged foods. Mediation analyses were used to examine whether changes in disinhibition and restraint mediated the relationship between intervention and weight change during initial weight loss (0-6 months), continued weight loss (6-12 months), or weight loss maintenance (12-24 months) phases. Only decreases in disinhibition between baseline and 6 months mediated the intervention effect on initial weight loss. Our results suggest the mediation effects of these eating behaviors are modest and other factors contribute to a larger, more complex long-term weight loss prognosis.

  7. Antagonism of corticotrophin-releasing factor receptors in the fourth ventricle modifies responses to mild but not restraint stress

    OpenAIRE

    Miragaya, Joanna R.; Harris, Ruth B. S.

    2008-01-01

    Repeated restraint stress (RRS; 3 h of restraint on 3 consecutive days) in rodents produces temporary hypophagia, but a long-term downregulation of body weight. The mild stress (MS) of an intraperitoneal injection of saline and housing in a novel room for 2 h also inhibits food intake and weight gain, but the effects are smaller than for RRS. Previous exposure to RRS exaggerates hypophagia, glucocorticoid release, and anxiety-type behavior caused by MS. Here we tested the involvement of brain...

  8. Environmental Enrichment Blunts Ethanol Consumption after Restraint Stress in C57BL/6 Mice.

    Directory of Open Access Journals (Sweden)

    Priscila Marianno

    Full Text Available Elevated alcohol intake after abstinence is a key feature of the addiction process. Some studies have shown that environmental enrichment (EE affects ethanol intake and other reinforcing effects. However, different EE protocols may vary in their ability to influence alcohol consumption and stress-induced intake. The present study evaluated whether short (3 h or continuous (24 h EE protocols affect ethanol consumption after periods of withdrawal. Mice were challenged with stressful stimuli (24 h isolation and restraint stress to evaluate the effects of stress on drinking. Male C57BL/6 mice were subjected to a two-bottle choice drinking-in-the-dark paradigm for 15 days (20% ethanol and water, 2 h/day, acquisition phase. Control mice were housed under standard conditions (SC. In the first experiment, one group of mice was housed under EE conditions 24 h/day (EE24h. In the second experiment, the exposure to EE was reduced to 3 h/day (EE3h. After the acquisition phase, the animals were deprived of ethanol for 6 days, followed by 2 h ethanol access once a week. Animals were tested in the elevated plus maze (EPM during ethanol withdrawal. During the last 2 weeks, the mice were exposed to 24 h ethanol access. A 1-h restraint stress test was performed immediately before the last ethanol exposure. EE24h but not EE3h increased anxiety-like behavior during withdrawal compared to controls. Neither EE24h nor EE3h affected ethanol consumption during the 2 h weekly exposure periods. However, EE24h and EE3h mice that were exposed to acute restraint stress consumed less ethanol than controls during a 24 h ethanol access. These results showed that EE reduces alcohol intake after an acute restraint stress.

  9. Repeated restraint stress lowers the threshold for response to third ventricle CRF administration.

    Science.gov (United States)

    Harris, Ruth B S

    2017-03-01

    Rats and mice exposed to repeated stress or a single severe stress exhibit a sustained increase in energetic, endocrine, and behavioral response to subsequent novel mild stress. This study tested whether the hyper-responsiveness was due to a lowered threshold of response to corticotropin releasing factor (CRF) or an exaggerated response to a standard dose of CRF. Male Sprague-Dawley rats were subjected to 3h of restraint on each of 3 consecutive days (RRS) or were non-restrained controls. RRS caused a temporary hypophagia but a sustained reduction in body weight. Eight days after the end of restraint, rats received increasing third ventricle doses of CRF (0-3.0μg). The lowest dose of CRF (0.25μg) increased corticosterone release in RRS, but not control rats. Higher doses caused the same stimulation of corticosterone in the two groups of rats. Fifteen days after the end of restraint, rats were food deprived during the light period and received increasing third ventricle doses of CRF at the start of the dark period. The lowest dose of CRF inhibited food intake during the first hour following infusion in RRS, but not control rats. All other doses of CRF inhibited food intake to the same degree in both RRS and control rats. The lowered threshold of response to central CRF is consistent with the chronic hyper-responsiveness to CRF and mild stress in RRS rats during the post-restraint period. Copyright © 2016 Elsevier Inc. All rights reserved.

  10. Housing in Pyramid Counteracts Neuroendocrine and Oxidative Stress Caused by Chronic Restraint in Rats

    Directory of Open Access Journals (Sweden)

    M. Surekha Bhat

    2007-01-01

    Full Text Available The space within the great pyramid and its smaller replicas is believed to have an antistress effect. Research has shown that the energy field within the pyramid can protect the hippocampal neurons of mice from stress-induced atrophy and also reduce neuroendocrine stress, oxidative stress and increase antioxidant defence in rats. In this study, we have, for the first time, attempted to study the antistress effects of pyramid exposure on the status of cortisol level, oxidative damage and antioxidant status in rats during chronic restraint stress. Adult female Wistar rats were divided into four groups as follows: normal controls (NC housed in home cage and left in the laboratory; restrained rats (with three subgroups subject to chronic restraint stress by placing in a wire mesh restrainer for 6 h per day for 14 days, the restrained controls (RC having their restrainers kept in the laboratory; restrained pyramid rats (RP being kept in the pyramid; and restrained square box rats (RS in the square box during the period of restraint stress everyday. Erythrocyte malondialdehyde (MDA and plasma cortisol levels were significantly increased and erythrocyte-reduced glutathione (GSH levels, erythrocyte glutathione peroxidase (GSH-Px and superoxide dismutase (SOD activities were significantly decreased in RC and RS rats as compared to NC. However, these parameters were maintained to near normal levels in RP rats which showed significantly decreased erythrocyte MDA and plasma cortisol and significantly increased erythrocyte GSH levels, erythrocyte GSH-Px and SOD activities when compared with RS rats. The results showed that housing in pyramid counteracts neuroendocrine and oxidative stress caused by chronic restraint in rats.

  11. Intrinsic brain subsystem associated with dietary restraint, disinhibition and hunger: an fMRI study.

    Science.gov (United States)

    Zhao, Jizheng; Li, Mintong; Zhang, Yi; Song, Huaibo; von Deneen, Karen M; Shi, Yinggang; Liu, Yijun; He, Dongjian

    2017-02-01

    Eating behaviors are closely related to body weight, and eating traits are depicted in three dimensions: dietary restraint, disinhibition, and hunger. The current study aims to explore whether these aspects of eating behaviors are related to intrinsic brain activation, and to further investigate the relationship between the brain activation relating to these eating traits and body weight, as well as the link between function connectivity (FC) of the correlative brain regions and body weight. Our results demonstrated positive associations between dietary restraint and baseline activation of the frontal and the temporal regions (i.e., food reward encoding) and the limbic regions (i.e., homeostatic control, including the hypothalamus). Disinhibition was positively associated with the activation of the frontal motivational system (i.e., OFC) and the premotor cortex. Hunger was positively related to extensive activations in the prefrontal, temporal, and limbic, as well as in the cerebellum. Within the brain regions relating to dietary restraint, weight status was negatively correlated with FC of the left middle temporal gyrus and left inferior temporal gyrus, and was positively associated with the FC of regions in the anterior temporal gyrus and fusiform visual cortex. Weight status was positively associated with the FC within regions in the prefrontal motor cortex and the right ACC serving inhibition, and was negatively related with the FC of regions in the frontal cortical-basal ganglia-thalamic circuits responding to hunger control. Our data depicted an association between intrinsic brain activation and dietary restraint, disinhibition, and hunger, and presented the links of their activations and FCs with weight status.

  12. Adrenocortical and behavioural response to chronic restraint stress in neurokinin-1 receptor knockout mice.

    Science.gov (United States)

    Delgado-Morales, Raúl; del Río, Eva; Gómez-Román, Almudena; Bisagno, Verónica; Nadal, Roser; de Felipe, Carmen; Armario, Antonio

    2012-02-01

    Brain substance P and its receptor (neurokinin-1, NK1) have a widespread brain distribution and are involved in an important number of behavioural and physiological responses to emotional stimuli. However, the role of NK1 receptors in the consequences of exposure to chronic stress has not been explored. The present study focused on the role of these receptors in the hypothalamic-pituitary-adrenal (HPA) response to daily repeated restraint stress (evaluated by plasma corticosterone levels), as well as on the effect of this procedure on anxiety-like behaviour, spatial learning and memory in the Morris water maze (MWM), a hippocampus-dependent task. Adult null mutant NK1-/- mice, with a C57BL/6J background, and the corresponding wild-type mice showed similar resting corticosterone levels and, also, did not differ in corticosterone response to a first restraint. Nevertheless, adaptation to the repeated stressor was faster in NK1-/- mice. Chronic restraint modestly increased anxiety-like behaviour in the light-dark test, irrespective of genotype. Throughout the days of the MWM trials, NK1-/- mice showed a similar learning rate to that of wild-type mice, but had lower levels of thigmotaxis and showed a better retention in the probe trial. Chronic restraint stress did not affect these variables in either genotype. These results indicate that deletion of the NK1 receptor does not alter behavioural susceptibility to chronic repeated stress in mice, but accelerates adaptation of the HPA axis. In addition, deletion may result in lower levels of thigmotaxis and improved short-term spatial memory, perhaps reflecting a better learning strategy in the MWM. Copyright © 2011 Elsevier Inc. All rights reserved.

  13. The Effects of Soldier Gear Encumbrance on Restraints in a Frontal Crash Environment

    Science.gov (United States)

    2015-08-31

    ASME 2015 IDETC/ CIE AVT-7-1 Advances in Military and Commercial Ground Vehicle Design Sebastian Karwaczynski Lead Restraint Development Engineer...release; distribution unlimited 13. SUPPLEMENTARY NOTES ASME 2015 IDETC/ CIE AVT-7-1 Advances in Military and Commercial Ground Vehicle Design 14...has to date not accounted for the Soldier gear burden. •Actual loads imparted onto the occupant in a representative military vehicle crash test

  14. Variation in Behavioral Reactivity Is Associated with Cooperative Restraint Training Efficiency

    OpenAIRE

    Bliss-Moreau, Eliza; Moadab, Gilda

    2016-01-01

    Training techniques that prepare laboratory animals to participate in testing via cooperation are useful tools that have the potential to benefit animal wellbeing. Understanding how animals systematically vary in their cooperative training trajectories will help trainers to design effective and efficient training programs. In the present report we document an updated method for training rhesus monkeys to cooperatively participate in restraint in a ‘primate chair.’ We trained 14 adult male mac...

  15. Retrospective analysis of detomidine infusion for standing chemical restraint in 51 horses.

    Science.gov (United States)

    Wilson, D V; Bohart, G V; Evans, A T; Robertson, S; Rondenay, Y

    2002-01-01

    To assess the effectiveness of a detomidine infusion technique to provide standing chemical restraint in the horse. Retrospective study. Fifty-one adult horses aged 9.5 ± 6.9 years (range 1-23 years) and weighing 575 ± 290.3 kg. Records of horses presented to our clinic over a 3-year period in which a detomidine infusion was used to provide standing chemical restraint were reviewed. Information relating to the types of procedure performed, duration of infusion, drug dosages and adjunct drugs administered was retrieved. Detomidine was administered as an initial bolus loading dose (mean ± SD) of 7.5 ± 1.87 μg kg -1 . The initial infusion rate was 0.6 μg kg -1 minute -1 , and this was halved every 15 minutes. The duration of the infusion ranged from 20 to 135 minutes. Twenty horses received additional detomidine or butorphanol during the procedure. All horses undergoing surgery received local anesthesia or epidural analgesia in addition to the detomidine infusion. A wide variety of procedures were performed in these horses. Detomidine administered by infusion provides prolonged periods of chemical restraint in standing horses. Supplemental sedatives or analgesics may be needed in horses undergoing surgery. An effective method that provides prolonged periods of chemical restraint in standing horses is described. The infusion alone did not provide sufficient analgesia for surgery and a significant proportion of animals required supplemental sedatives and analgesics. Copyright © 2002 Association of Veterinary Anaesthetists and American College of Veterinary Anesthesia and Analgesia. Published by Elsevier Ltd. All rights reserved.

  16. Influence of omega-3 fatty acid status on the way rats adapt to chronic restraint stress.

    Directory of Open Access Journals (Sweden)

    Marie Hennebelle

    Full Text Available Omega-3 fatty acids are important for several neuronal and cognitive functions. Altered omega-3 fatty acid status has been implicated in reduced resistance to stress and mood disorders. We therefore evaluated the effects of repeated restraint stress (6 h/day for 21 days on adult rats fed omega-3 deficient, control or omega-3 enriched diets from conception. We measured body weight, plasma corticosterone and hippocampus glucocorticoid receptors and correlated these data with emotional and depression-like behaviour assessed by their open-field (OF activity, anxiety in the elevated-plus maze (EPM, the sucrose preference test and the startle response. We also determined their plasma and brain membrane lipid profiles by gas chromatography. Repeated restraint stress caused rats fed a control diet to lose weight. Their plasma corticosterone increased and they showed moderate behavioural changes, with increases only in grooming (OF test and entries into the open arms (EPM. Rats fed the omega-3 enriched diet had a lower stress-induced weight loss and plasma corticosterone peak, and reduced grooming. Rats chronically lacking omega-3 fatty acid exhibited an increased startle response, a stress-induced decrease in locomotor activity and exaggerated grooming. The brain omega-3 fatty acids increased as the dietary omega-3 fatty acids increased; diets containing preformed long-chain omega-3 fatty acid were better than diets containing the precursor alpha-linolenic acid. However, the restraint stress reduced the amounts of omega-3 incorporated. These data showed that the response to chronic restraint stress was modulated by the omega-3 fatty acid supply, a dietary deficiency was deleterious while enrichment protecting against stress.

  17. Association between weight and risk of crash-related injuries for children in child restraints.

    Science.gov (United States)

    Zonfrillo, Mark R; Elliott, Michael R; Flannagan, Carol A; Durbin, Dennis R

    2011-12-01

    To determine the association between weight and the risk of injury in motor vehicle crashes (MVCs) for children 1 through 8 years of age who were using child restraints. This was a cross-sectional study of children 1 to 8 years of age in MVCs, in which cases from the National Automotive Sampling System Crashworthiness Data System were used. Abbreviated Injury Scale scores of ≥2 indicated clinically significant injuries. The National Automotive Sampling System Crashworthiness Data System study sample included 650 children 1 to 5 years of age in forward-facing child restraints who weighed 20 to 65 lb and 344 children 3 to 8 years of age in belt-positioning booster seats who weighed 30 to 100 lb. With adjustment for seating position, type of vehicle, direction of impact, crash severity, and vehicle model year, there was no association between absolute weight and clinically significant injuries in either age group (odds ratio: 1.17 [95% confidence interval: 0.96-1.42] for children 1-5 years of age in forward-facing child restraints and 1.22 [95% confidence interval: 0.96-1.55] for children 3-8 years of age in belt-positioning booster seats). The risk of clinically significant injuries was not associated with weight across a broad weight range in this sample of children in MVCs who were using child restraint systems. Parents should continue to restrain their children according to current recommendations from the American Academy of Pediatrics and the National Highway Traffic Safety Administration.

  18. Applying sensory modulation to mental health inpatient care to reduce seclusion and restraint: a case control study.

    Science.gov (United States)

    Andersen, Charlotte; Kolmos, Anne; Andersen, Kjeld; Sippel, Volkmar; Stenager, Elsebeth

    2017-10-01

    Clinical training in managing conflicts and preventing violence seldom contains sensory modulation (SM) as a method to de-escalate and prevent restraint and seclusion. Sensory-based interventions promote adaptive regulation of arousal and emotion. SM is a complementary approach that is associated with reduced rates of seclusion and restraint in mental healthcare, but there is need for more research in this area. Using SM to reduce restraint and seclusion in inpatient mental health care. The study included two similar psychiatric units where one unit implemented SM and one unit served as the control group. In the very beginning of the study, a staff-training program in the use of SM including assessment tools and intervention strategies was established. Data on restraint and forced medicine were sampled post the course of the year of implementation and compared with the control group. The use of belts decreased with 38% compared to the control group. The use of forced medication decreased with 46% compared to the control group. Altogether the use of physical restraint and forced medication decreased significantly with 42% (p mental healthcare facilities has a significant effect on the reduction of restraint and seclusion. As a part of the implementation, staff training and education in SM are crucial.

  19. Nursing staff members' intentions to use physical restraints with older people: testing the theory of reasoned action.

    Science.gov (United States)

    Werner, P; Mendelsson, G

    2001-09-01

    To examine nursing staff members' attitudes, subjective norms, moral obligations and intentions to use physical restraints, using the Theory of Reasoned Action (TRA). During the last two decades an extensive body of research has examined nurses' attitudes as one of the main factors affecting the decision to use or not to use physical restraints with older persons. However, no studies have examined empirically the antecedents to nurses' intentions to use physical restraints within a theoretically based framework. A correlational design was used with 303 nursing staff members from an 800-bed elder care hospital in central Israel. Participants completed a questionnaire including questions based on the TRA as well as socio-demographic and professional characteristics. Regression analyses found attitudes, subjective norms and moral considerations to be significantly associated to intention to use physical restraints with older people. The TRA explained 48% of the variance in nurses' intentions. The TRA proved to be a useful framework for examining nurses' intentions to use physical restraints. Nurses' attitudes, beliefs and expectations of significant others should be examined before implementing educational programmes regarding the use of physical restraints.

  20. Impact of restraint and disinhibition on PYY plasma levels and subjective feelings of appetite.

    Science.gov (United States)

    Martins, C; Robertson, M D; Morgan, L M

    2010-10-01

    The impact of eating behaviours on circulating levels of appetite-regulating hormones remains largely unknown. The aims of this study were to assess the role of restraint and disinhibition on fasting/postprandial peptide YY (PYY) plasma levels and subjective feelings of appetite in normal-weight individuals and to determine whether the effect was energy load dependent. 33 participants (12 men) were classified as restrained/unrestrained and low/high in disinhibition based on Three Factor Eating Questionnaire-18R and Dutch Eating Behaviour Questionnaire. The impact of restraint/disinhibition on PYY plasma levels and feelings of appetite was measured, after a 500kcal and 1000kcal breakfast, using a randomised crossover design. Restraint did not impact on either fasting or postprandial PYY plasma levels, but participants with high disinhibition had a tendency towards a blunted postprandial PYY response. Moreover, restrained eaters reported lower ratings of prospective food consumption postprandially, and a tendency towards higher fullness/lower hunger. In conclusion, circulating PYY is unaffected by restrained eating behaviour, despite being associated with increased fullness and reduced hunger in the fed state. High levels of disinhibition tend to be associated with a blunted PYY response and this may contribute towards the susceptibility to overconsumption and increased risk of weight gain characteristic of this trait.

  1. Evaluation of Life Sciences Glovebox (LSG) and Multi-Purpose Crew Restraint Concepts

    Science.gov (United States)

    Whitmore, Mihriban

    2005-01-01

    Within the scope of the Multi-purpose Crew Restraints for Long Duration Spaceflights project, funded by Code U, it was proposed to conduct a series of evaluations on the ground and on the KC-135 to investigate the human factors issues concerning confined/unique workstations, such as the design of crew restraints. The usability of multiple crew restraints was evaluated for use with the Life Sciences Glovebox (LSG) and for performing general purpose tasks. The purpose of the KC-135 microgravity evaluation was to: (1) to investigate the usability and effectiveness of the concepts developed, (2) to gather recommendations for further development of the concepts, and (3) to verify the validity of the existing requirements. Some designs had already been tested during a March KC-135 evaluation, and testing revealed the need for modifications/enhancements. This flight was designed to test the new iterations, as well as some new concepts. This flight also involved higher fidelity tasks in the LSG, and the addition of load cells on the gloveports.

  2. Restraint stress in lactating mice alters the levels of sulfur-containing amino acids in milk.

    Science.gov (United States)

    Nishigawa, Takuma; Nagamachi, Satsuki; Ikeda, Hiromi; Chowdhury, Vishwajit S; Furuse, Mitsuhiro

    2018-03-30

    It is well known that maternal stress during the gestation and lactation periods induces abnormal behavior in the offspring and causes a lowering of the offspring's body weight. Various causes of maternal stress during the lactation period, relating to, for example, maternal nutritional status and reduced maternal care, have been considered. However, little is known about the effects on milk of maternal stress during the lactation period. The current study aimed to determine whether free amino acids, with special reference to sulfur-containing amino acids in milk, are altered by restraint stress in lactating mice. The dams in the stress group were restrained for 30 min at postnatal days 2, 4, 6, 8, 10 and 12. Restraint stress caused a reduction in the body weight of lactating mice. The concentration of taurine and cystathionine in milk was significantly higher in the stress group, though stress did not alter their concentration in maternal plasma. The ratio of taurine concentration in milk to its concentration in maternal plasma was significantly higher in the stress group, suggesting that stress promoted taurine transportation into milk. Furthermore, taurine concentration in milk was positively correlated with corticosterone levels in plasma. In conclusion, restraint stress in lactating mice caused the changes in the metabolism and in the transportation of sulfur-containing amino acids and resulted in higher taurine concentration in milk. Taurine concentration in milk could also be a good parameter for determining stress status in dams.

  3. The mGlu2/3 Receptor Agonists LY354740 and LY379268 Differentially Regulate Restraint-Stress-Induced Expression of c-Fos in Rat Cerebral Cortex

    Directory of Open Access Journals (Sweden)

    M. M. Menezes

    2013-01-01

    Full Text Available Metabotropic glutamate 2/3 (mGlu2/3 receptors have emerged as potential therapeutic targets due to the ability of mGlu2/3 receptor agonists to modulate excitatory transmission at specific synapses. LY354740 and LY379268 are selective and potent mGlu2/3 receptor agonists that show both anxiolytic- and antipsychotic-like effects in animal models. We compared the efficacy of LY354740 and LY379268 in attenuating restraint-stress-induced expression of the immediate early gene c-Fos in the rat prelimbic (PrL and infralimbic (IL cortex. LY354740 (10 and 30 mg/kg, i.p. showed statistically significant and dose-related attenuation of stress-induced increase in c-Fos expression, in the rat cortex. By contrast, LY379268 had no effect on restraint-stress-induced c-Fos upregulation (0.3–10 mg/kg, i.p.. Because both compounds inhibit serotonin 2A receptor (5-HT2AR-induced c-Fos expression, we hypothesize that LY354740 and LY379268 have different in vivo properties and that 5-HT2AR activation and restraint stress induce c-Fos through distinct mechanisms.

  4. A chemo-mechanical model coupled with thermal effect on the hollow core–shell electrodes in lithium-ion batteries

    Directory of Open Access Journals (Sweden)

    Bin Hu

    2017-07-01

    Full Text Available Electrode is a key component to remain durability and safety of lithium-ion (Li-ion batteries. Li-ion insertion/removal and thermal expansion mismatch may induce high stress in electrode during charging and discharging processes. In this paper, we present a continuum model based on COMSOL Multiphysics software, which involves thermal, chemical and mechanical behaviors of electrodes. The results show that, because of diffusion-induced stress and thermal mismatch, the electrode geometry plays an important role in diffusion kinetics of Li-ions. A higher local compressive stress results in a lower Li-ion concentration and thus a lower capacity when a particle is embedded another, which is in agreement with experimental observations. Keywords: Lithium-ion battery, Diffusion-induced stress, COMSOL, Chemo-mechanical, Electrode

  5. Experiments on graphite block gaps connected with leak flow in bottom-core structure of experimental very high-temperature gas-cooled reactor

    International Nuclear Information System (INIS)

    Kikuchi, Kenji; Futakawa, Masatoshi; Takizuka, Takakazu; Kaburaki, Hideo; Sanokawa, Konomo

    1984-01-01

    In order to minimize the leak flow rate of an experimental VHTR (a multi-purpose very high-temperature gas-cooled reactor), the graphite blocks are tightened to reduce the gap distance between blocks by core restrainers surrounded outside of the fixed reflectors of the bottom-core structure and seal elements are placed in the gaps. By using a 1/2.75-scale model of the bottom-core structure, the experiments on the following items have been carried out: a relationship between core restraint force and block gap, a relationship between core restraint force and inclined angle of the model, leak flow characteristics of seal elements etc. The conclusions derived from the experiments are as follows: (1) Core restraint force is significantly effective for decreasing the gap distance between hot plenum blocks, but ineffective for the gap between hot plenum block and fixed reflector. (2) Graphite seal element reduces the leak flow rate from the top surface of hot plenum block into plenum region to one-third. (author)

  6. Finite Element Models Development of Car Seats With Passive Head Restraints to Study Their Meeting Requirements for EURO NCAP

    Directory of Open Access Journals (Sweden)

    D. Yu. Solopov

    2014-01-01

    Full Text Available In performing calculations to evaluate passive safety of car seats by computer modelling methods it is desirable to use the final element models (FEM thereby providing the greatest accuracy of calculation results. Besides, it is expedient to use FEM, which can be calculated by computer for a small period of time to give preliminary results for short terms.The paper describes the features to evaluate a passive safety, which is ensured by the developed KEM of seats with passive head restraints according to requirements of the EURO NCAP.Besides, accuracy of calculated results that is provided by the developed KEM was evaluated. Accuracy evaluation was accomplished in relation to the results obtained the by specialists of the organization conducting similar researches (LSTC.This work was performed within the framework of a technique, which allows us to develop effectively the car seat designs both with passive, and active head restraints, meeting requirements for passive safety.By results of made calculations and experiments it was found that when evaluating by the EURO NCAP technique the "rough" KEM (the 1st and 2nd levels can be considered as rational ones (in terms of labour costs for its creation and problem solving as well as by result errors and it is expedient to use them for preliminary and multivariate calculations. Detailed models (the 3rd level provide the greatest accuracy (the greatest accuracy is reached with the evaluated impact of 16km/h speed under the loading conditions "moderate impact". A relative error of full head acceleration is of 12%.In evaluation by EURO NCAP using NIC criterion a conclusion can be drawn that the seat models of the 2nd level (467 936 KE and the 3rd level (1 255 358 KE meet the passive safety requirements according to EURO NCAP requirements under "light", "moderate", and "heavy" impacts.In evaluation by EURO NCAP for preliminary and multivariate calculations a model of the middle level (consisting of 467

  7. Effects of chronic restraint stress and estradiol on open field activity, spatial memory, and monoaminergic neurotransmitters in ovariectomized rats.

    Science.gov (United States)

    Bowman, R E; Ferguson, D; Luine, V N

    2002-01-01

    Twenty-one days of chronic restraint stress impairs male rat performance on the radial arm maze [Luine et al. (1994) Brain Res. 639, 167-170], but enhances female rat performance [Bowman et al. (2001) Brain Res. 904, 279-289]. To assess possible ovarian hormone mechanisms underlying this sexually dimorphic response to stress, we examined chronic stress effects in ovariectomized rats. Ovariectomized rats received Silastic capsule implants containing cholesterol or estradiol and were assigned to a daily restraint stress (21 days, 6 h/day) or non-stress group. Following the stress period, subjects were tested for open field activity and radial arm maze performance. Stress and estradiol treatment affected open field activity. All stressed animals, with or without estradiol treatment, made fewer total outer sector crossings. In contrast, estradiol-treated animals, with or without stress, made more inner sector visits, an indication that estradiol decreased anxious behavior on the open field across time. As measured by the total number of visits required to complete the task, stress did not affect radial arm maze performance in ovariectomized rats, but estradiol-treated animals, with or without stress, performed better than non-treated animals on the radial arm maze. Stressed subjects receiving estradiol showed the best radial arm maze performance. Following killing, tissue samples were obtained from various brain regions known to contribute to learning and memory, and monoamine and metabolite levels were measured. Several changes were observed in response to both stress and estradiol. Most noteworthy, stress treatment decreased homovanillic acid levels in the prefrontal cortex, an effect not previously observed in stressed intact females. Estradiol treatment increased norepinephrine levels in CA3 region of the hippocampus, mitigating stress-dependent changes. Both stress and estradiol decreased dentate gyrus levels of 5-hydroxyindole acetic acid. In summary, the current

  8. The developmental effects of media-ideal internalization and self-objectification processes on adolescents' negative body-feelings, dietary restraint, and binge eating.

    Science.gov (United States)

    Dakanalis, Antonios; Carrà, Giuseppe; Calogero, Rachel; Fida, Roberta; Clerici, Massimo; Zanetti, Maria Assunta; Riva, Giuseppe

    2015-08-01

    Despite accumulated experimental evidence of the negative effects of exposure to media-idealized images, the degree to which body image, and eating related disturbances are caused by media portrayals of gendered beauty ideals remains controversial. On the basis of the most up-to-date meta-analysis of experimental studies indicating that media-idealized images have the most harmful and substantial impact on vulnerable individuals regardless of gender (i.e., "internalizers" and "self-objectifiers"), the current longitudinal study examined the direct and mediated links posited in objectification theory among media-ideal internalization, self-objectification, shame and anxiety surrounding the body and appearance, dietary restraint, and binge eating. Data collected from 685 adolescents aged between 14 and 15 at baseline (47 % males), who were interviewed and completed standardized measures annually over a 3-year period, were analyzed using a structural equation modeling approach. Results indicated that media-ideal internalization predicted later thinking and scrutinizing of one's body from an external observer's standpoint (or self-objectification), which then predicted later negative emotional experiences related to one's body and appearance. In turn, these negative emotional experiences predicted subsequent dietary restraint and binge eating, and each of these core features of eating disorders influenced each other. Differences in the strength of these associations across gender were not observed, and all indirect effects were significant. The study provides valuable information about how the cultural values embodied by gendered beauty ideals negatively influence adolescents' feelings, thoughts and behaviors regarding their own body, and on the complex processes involved in disordered eating. Practical implications are discussed.

  9. Side core lifter

    Energy Technology Data Exchange (ETDEWEB)

    Edelman, Ya A

    1982-01-01

    A side core lifter is proposed which contains a housing with guide slits and a removable core lifter with side projections on the support section connected to the core receiver. In order to preserve the structure of the rock in the core sample by means of guaranteeing rectilinear movement of the core lifter in the rock, the support and core receiver sections are hinged. The device is equipped with a spring for angular shift in the core-reception part.

  10. Initial Comparison of Direct and Legacy Modeling Approaches for Radial Core Expansion Analysis

    International Nuclear Information System (INIS)

    Shemon, Emily R.

    2016-01-01

    Radial core expansion in sodium-cooled fast reactors provides an important reactivity feedback effect. As the reactor power increases due to normal start up conditions or accident scenarios, the core and surrounding materials heat up, causing both grid plate expansion and bowing of the assembly ducts. When the core restraint system is designed correctly, the resulting structural deformations introduce negative reactivity which decreases the reactor power. Historically, an indirect procedure has been used to estimate the reactivity feedback due to structural deformation which relies upon perturbation theory and coupling legacy physics codes with limited geometry capabilities. With advancements in modeling and simulation, radial core expansion phenomena can now be modeled directly, providing an assessment of the accuracy of the reactivity feedback coefficients generated by indirect legacy methods. Recently a new capability was added to the PROTEUS-SN unstructured geometry neutron transport solver to analyze deformed meshes quickly and directly. By supplying the deformed mesh in addition to the base configuration input files, PROTEUS-SN automatically processes material adjustments including calculation of region densities to conserve mass, calculation of isotopic densities according to material models (for example, sodium density as a function of temperature), and subsequent re-homogenization of materials. To verify the new capability of directly simulating deformed meshes, PROTEUS-SN was used to compute reactivity feedback for a series of contrived yet representative deformed configurations for the Advanced Burner Test Reactor design. The indirect legacy procedure was also performed to generate reactivity feedback coefficients for the same deformed configurations. Interestingly, the legacy procedure consistently overestimated reactivity feedbacks by 35% compared to direct simulations by PROTEUS-SN. This overestimation indicates that the legacy procedures are in fact

  11. Initial Comparison of Direct and Legacy Modeling Approaches for Radial Core Expansion Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Shemon, Emily R. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-10-10

    Radial core expansion in sodium-cooled fast reactors provides an important reactivity feedback effect. As the reactor power increases due to normal start up conditions or accident scenarios, the core and surrounding materials heat up, causing both grid plate expansion and bowing of the assembly ducts. When the core restraint system is designed correctly, the resulting structural deformations introduce negative reactivity which decreases the reactor power. Historically, an indirect procedure has been used to estimate the reactivity feedback due to structural deformation which relies upon perturbation theory and coupling legacy physics codes with limited geometry capabilities. With advancements in modeling and simulation, radial core expansion phenomena can now be modeled directly, providing an assessment of the accuracy of the reactivity feedback coefficients generated by indirect legacy methods. Recently a new capability was added to the PROTEUS-SN unstructured geometry neutron transport solver to analyze deformed meshes quickly and directly. By supplying the deformed mesh in addition to the base configuration input files, PROTEUS-SN automatically processes material adjustments including calculation of region densities to conserve mass, calculation of isotopic densities according to material models (for example, sodium density as a function of temperature), and subsequent re-homogenization of materials. To verify the new capability of directly simulating deformed meshes, PROTEUS-SN was used to compute reactivity feedback for a series of contrived yet representative deformed configurations for the Advanced Burner Test Reactor design. The indirect legacy procedure was also performed to generate reactivity feedback coefficients for the same deformed configurations. Interestingly, the legacy procedure consistently overestimated reactivity feedbacks by 35% compared to direct simulations by PROTEUS-SN. This overestimation indicates that the legacy procedures are in fact

  12. Reactor-core-reactivity control device

    International Nuclear Information System (INIS)

    Miura, Teruo; Sakuranaga, Tomonobu.

    1983-01-01

    Purpose: To improve the reactor safety upon failures of control rod drives by adapting a control rod not to drop out accidentally from the reactor core but be inserted into the reactor core. Constitution: The control rod is entered or extracted as usual from the bottom of the pressure vessel. A space is provided above the reactor core within the pressure vessel, in which the moving scope of the control rod is set between the space above the reactor core and the reactor core. That is, the control rod is situated above the reactor core upon extraction thereof and, if an accident occurs to the control rod drive mechanisms to detach the control rod and the driving rod, the control rod falls gravitationally into the reactor core to improve the reactor safety. In addition, since the speed limiter is no more required to the control rod, the driving force can be decreased to reduce the size of the rod drive mechanisms. (Ikeda, J.)

  13. Automated Core Design

    International Nuclear Information System (INIS)

    Kobayashi, Yoko; Aiyoshi, Eitaro

    2005-01-01

    Multistate searching methods are a subfield of distributed artificial intelligence that aims to provide both principles for construction of complex systems involving multiple states and mechanisms for coordination of independent agents' actions. This paper proposes a multistate searching algorithm with reinforcement learning for the automatic core design of a boiling water reactor. The characteristics of this algorithm are that the coupling structure and the coupling operation suitable for the assigned problem are assumed and an optimal solution is obtained by mutual interference in multistate transitions using multiagents. Calculations in an actual plant confirmed that the proposed algorithm increased the convergence ability of the optimization process

  14. Space reactor preliminary mechanical design

    International Nuclear Information System (INIS)

    Meier, K.L.

    1983-01-01

    An analysis was performed on the SABRE reactor space power system to determine the effect of the number and size of heat pipes on the design parameters of the nuclear subsystem. Small numbers of thin walled heat pipes were found to give a lower subsystem mass, but excessive fuel swelling resulted. The SP-100 preliminary design uses 120 heat pipes because of acceptable fuel swelling and a minimum nuclear subsystem mass of 1875 kg. Salient features of the reactor preliminary design are: individual fuel modules, ZrO 2 block core mounts, bolted collar fuel module restraints, and a BeO central plug

  15. Adaptive Queue Management with Restraint on Non-Responsive Flows

    Directory of Open Access Journals (Sweden)

    Lan Li

    2003-12-01

    Full Text Available This paper proposes an adaptive queue management scheme (adaptive RED to improve Random Early Detection (RED on restraining non-responsive flows. Due to a lack of flow control mechanism, non-responsive flows can starve responsive flows for buffer and bandwidth at the gateway. In order to solve the disproportionate resource problem, RED framework is modified in this way: on detecting when the non-responsive flows starve the queue, packet-drop intensity (Max_p in RED can be adaptively adjusted to curb non-responsive flows for resource fair-sharing, such as buffer and bandwidth fair-sharing. Based on detection of traffic behaviors, intentionally restraining nonresponsive flows is to increase the throughput and decrease the drop rate of responsive flows. Our experimental results based on adaptive RED shows that the enhancement of responsive traffic and the better sharing of buffer and bandwidth can be achieved under a variety of traffic scenarios.

  16. Study on a mechanical snubber with an adjustment mechanism for resisting force

    International Nuclear Information System (INIS)

    Ohmata, Kenichiro; Miyanaga, Hiroyuki.

    1991-01-01

    The mechanical snubber is an earthquakeproof device for a piping system under particular circumstances such as high temperature and radioactivity. It restrains the piping system by a strong resisting force during an earthquake. This strong force can cause elastic failure of grooves on a brake disk, where steel balls are placed. In this report, an improved mechanical snubber having an adjustment mechanism for resisting force is proposed in order to obtain a mechanical snubber which has almost the same restraint effect and less resisting force in comparison with a conventional mechanical snubber. The resisting force characteristics and the restraint effect of the improved mechanical snubber applied to a simple beam are discussed both numerically and experimentally. The digital simulations are carried out using the Continuous System Simulation Language (CSSL). (author)

  17. Control device for a nuclear reactor with a multitude of control rods, extending into the reactor core from above, with linear drive mechanisms and additional gripper devices

    International Nuclear Information System (INIS)

    Bevilacqua, F.

    1979-01-01

    The components of the additional gripper devices with magnetically operated finger-shaped latches are separated from the also magnetically operated latches of the linear drive mechanisms in order to avoid common-mode failures when fast shutdown is required. Only part of the safety rods are held by the additional gripping devices in the withdrawn position. There is provided for recording elements indicating positively which one of the safety locks is gearing with the control rods. At the upper end of each control rod there is a coupling head held by electromagnetically operated locking devices in the withdrawn position, if control power is available. (DG) [de

  18. Utilization of paramagnetic relaxation enhancements for high-resolution NMR structure determination of a soluble loop-rich protein with sparse NOE distance restraints

    International Nuclear Information System (INIS)

    Furuita, Kyoko; Kataoka, Saori; Sugiki, Toshihiko; Hattori, Yoshikazu; Kobayashi, Naohiro; Ikegami, Takahisa; Shiozaki, Kazuhiro; Fujiwara, Toshimichi; Kojima, Chojiro

    2015-01-01

    NMR structure determination of soluble proteins depends in large part on distance restraints derived from NOE. In this study, we examined the impact of paramagnetic relaxation enhancement (PRE)-derived distance restraints on protein structure determination. A high-resolution structure of the loop-rich soluble protein Sin1 could not be determined by conventional NOE-based procedures due to an insufficient number of NOE restraints. By using the 867 PRE-derived distance restraints obtained from the NOE-based structure determination procedure, a high-resolution structure of Sin1 could be successfully determined. The convergence and accuracy of the determined structure were improved by increasing the number of PRE-derived distance restraints. This study demonstrates that PRE-derived distance restraints are useful in the determination of a high-resolution structure of a soluble protein when the number of NOE constraints is insufficient

  19. Ice cores and palaeoclimate

    International Nuclear Information System (INIS)

    Krogh Andersen, K.; Ditlevsen, P.; Steffensen, J.P.

    2001-01-01

    Ice cores from Greenland give testimony of a highly variable climate during the last glacial period. Dramatic climate warmings of 15 to 25 deg. C for the annual average temperature in less than a human lifetime have been documented. Several questions arise: Why is the Holocene so stable? Is climatic instability only a property of glacial periods? What is the mechanism behind the sudden climate changes? Are the increased temperatures in the past century man-made? And what happens in the future? The ice core community tries to attack some of these problems. The NGRIP ice core currently being drilled is analysed in very high detail, allowing for a very precise dating of climate events. It will be possible to study some of the fast changes on a year by year basis and from this we expect to find clues to the sequence of events during rapid changes. New techniques are hoped to allow for detection of annual layers as far back as 100,000 years and thus a much improved time scale over past climate changes. It is also hoped to find ice from the Eemian period. If the Eemian layers confirm the GRIP sequence, the Eemian was actually climatically unstable just as the glacial period. This would mean that the stability of the Holocene is unique. It would also mean, that if human made global warming indeed occurs, we could jeopardize the Holocene stability and create an unstable 'Eemian situation' which ultimately could start an ice age. Currenlty mankind is changing the composition of the atmosphere. Ice cores document significant increases in greenhouse gases, and due to increased emissions of sulfuric and nitric acid from fossil fuel burning, combustion engines and agriculture, modern Greenland snow is 3 - 5 times more acidic than pre-industrial snow (Mayewski et al., 1986). However, the magnitude and abruptness of the temperature changes of the past century do not exceed the magnitude of natural variability. It is from the ice core perspective thus not possible to attribute the

  20. Vibrational characterization of hexagonal duct core assemblies under various support conditions

    International Nuclear Information System (INIS)

    Bartholf, L.W.; Julyk, L.J.; Ryan, J.A.

    1989-03-01

    Analysis of the dynamic response of advanced Liquid Metal Reactor (LMR) core internals to seismic excitation requires a significant number of simplifying assumptions and idealizations to economically meet the constraints of present-day computer limitations. Fluid coupling and nonlinearities associated with inter-assembly lateral support stiffness and clearances of a large cluster of core internal assemblies are some of the factors that complicate the analytical procedure (Moran, 1976). Well defined test data were needed to quantify these and other uncertainties associated with the use of analytical or numerical computer codes used in the seismic design and analysis of reactor cores. The purpose of the present experimental program was to supplement existing data, such as reported in (Sasaki and Muto, 1983), by developing vibrational characteristics of core assemblies over a range of parameters relative to LMR conceptual designs. The parameters selected for this program were variations in number and location of restraints, restraint-pad to duct-load-pad clearances, and input forcing frequency and g-level. Feature tests were conducted to characterize load pad stiffness and coefficient of restitution, and to calibrate load pads to measure inter-assembly across-flat impact loads. Simulated full-size LMR hexagonal duct core assemblies were used in vibration tests. A single assembly and a row of five assemblies were tested in air to establish modal characteristics and forced response behavior. 2 refs., 7 figs., 1 tab

  1. Transient bowing of core assemblies in advanced liquid metal fast reactors

    International Nuclear Information System (INIS)

    Kamal, S.A.; Orechwa, Y.

    1986-01-01

    Two alternative core restraint concepts are considered for a conceptual design of a 900 MWth liquid metal fast reactor core with a heterogeneous layout. The two concepts, known as limited free bowing and free flowering, are evaluated based on core bowing criteria that emphasize the enhancement of inherent reactor safety. The core reactivity change during a postulated loss of flow transient is calculated in terms of the lateral displacements and displacement-reactivity-worths of the individual assemblies. The NUBOW-3D computer code is utilized to determine the assembly deformations and interassembly forces that arise when the assemblies are subjected to temperature gradients and irradiation induced creep and swelling during the reactor operation. The assembly ducts are made of the ferritic steel HT-9 and remain in the reactor core for four-years at full power condition. Whereas both restraint systems meet the bowing criteria, a properly designed limited free bowing system appears to be more advantageous than a free flowering system from the point of view of enhancing the reactor inherent safety

  2. Dephosphorylation of the Core Clock Protein KaiC in the Cyanobacterial KaiABC Circadian Oscillator Proceeds via an ATP Synthase Mechanism

    Energy Technology Data Exchange (ETDEWEB)

    Egli, Martin; Mori, Tetsuya; Pattanayek, Rekha; Xu, Yao; Qin, Ximing; Johnson, Carl H. (Vanderbilt)

    2014-10-02

    The circadian clock of the cyanobacterium Synechococcus elongatus can be reconstituted in vitro from three proteins, KaiA, KaiB, and KaiC in the presence of ATP, to tick in a temperature-compensated manner. KaiC, the central cog of this oscillator, forms a homohexamer with 12 ATP molecules bound between its N- and C-terminal domains and exhibits unusual properties. Both the N-terminal (CI) and C-terminal (CII) domains harbor ATPase activity, and the subunit interfaces between CII domains are the sites of autokinase and autophosphatase activities. Hydrolysis of ATP correlates with phosphorylation at threonine and serine sites across subunits in an orchestrated manner, such that first T432 and then S431 are phosphorylated, followed by dephosphorylation of these residues in the same order. Although structural work has provided insight into the mechanisms of ATPase and kinase, the location and mechanism of the phosphatase have remained enigmatic. From the available experimental data based on a range of approaches, including KaiC crystal structures and small-angle X-ray scattering models, metal ion dependence, site-directed mutagenesis (i.e., E318, the general base), and measurements of the associated clock periods, phosphorylation patterns, and dephosphorylation courses as well as a lack of sequence motifs in KaiC that are typically associated with known phosphatases, we hypothesized that KaiCII makes use of the same active site for phosphorylation and dephosphorlyation. We observed that wild-type KaiC (wt-KaiC) exhibits an ATP synthase activity that is significantly reduced in the T432A/S431A mutant. We interpret the first observation as evidence that KaiCII is a phosphotransferase instead of a phosphatase and the second that the enzyme is capable of generating ATP, both from ADP and P{sub i} (in a reversal of the ATPase reaction) and from ADP and P-T432/P-S431 (dephosphorylation). This new concept regarding the mechanism of dephosphorylation is also supported by the

  3. Educational intervention on physical restraint use in long-term care facilities – Systematic review and meta-analysis

    Directory of Open Access Journals (Sweden)

    Shao-Huan Lan

    2017-08-01

    Full Text Available “Physical restraint” formerly used as a measure of protection for psychiatric patients is now widely used. However, existing studies showed that physical restraint not only has inadequate effect of protection but also has negative effects on residents. To analyzes the impact of educational program on the physical restraint use in long-term care facilities. Design: A systematic review with meta-analysis and meta-regression. Eight databases, including Cochrane Library, ProQuest, PubMed, EMBASE, EBSCO, Web of Science, Ovid Medline and Physiotherapy Evidence Database (PEDro, were searched up to January 2017. Eligible studies were classified by intervention and accessed for quality using the Quality Assessment Tool for quantitative studies. Sixteen research articles were eligible in the final review; 10 randomize control trail studies were included in the analysis. The meta-analysis revealed that the use of physical restraint was significantly less often in the experimental (education group (OR = 0.55, 95% CI: 0.39 to 0.78, p < 0.001 compared to the control group. Meta-regression revealed the period of post education would have decreased the effect of the restraint educational program (β: 0.08, p = 0.002; instead, the longer education period and more times of education would have a stronger effect of reducing the use of physical restraint (β: −0.07, p < 0.001; β: −0.04, p = 0.056. The educational program had an effect on the reduced use of physical restraint. The results of meta-regression suggest that long-term care facilities should provide a continuous education program of physical restraint for caregivers.

  4. Evaluation Model for Restraint Effect of Pressure Induced Bending on the Plastic Crack Opening of Circumferential Through-Wall-Crack

    International Nuclear Information System (INIS)

    Kim, Jin-Weon

    2006-01-01

    Most of the pipe crack evaluation procedures, including leak-before-break (LBB) analysis, assume that the cracked pipe subjected to remote bending or internal pressure is free to rotate. In this case, the pressure induced bending (PIB) enhances crack opening of a through-wall-crack (TWC) in a pipe. In a real piping system, however, the PIB will be restrained because the ends of the pipe are constrained by the rest of the piping system. Hence, the amount of restraint affects the crack opening of a TWC in a pipe, and the restraint effect on crack opening directly affects the results of LBB evaluation. Therefore, it is necessary to investigate the restraint effect of PIB on crack opening displacement (COD) to quantify the uncertainties in current analysis procedures and to ensure the application of LBB concepts to nuclear piping systems. Recently, several researches were conducted to investigate the restraint effect of PIB on COD, and they proposed a simplified model to evaluate COD under restrained conditions. However, these results are quite limited because the restraint effect was evaluated only in terms of linear-elastic crack opening. In practice, the TWC in a pipe behaves plastically under normal operating loads, and the current LBB analysis methodologies require elastic-plastic crack opening evaluation. Therefore, this study evaluates the restraint effect of PIB on the plastic crack opening of a TWC in a pipe using finite element analysis under various influencing parameters. Based on these results, a closed-from model to be able to estimate the restraint effect of PIB on plastic crack opening is proposed

  5. Testosterone depletion increases the susceptibility of brain tissue to oxidative damage in a restraint stress mouse model.

    Science.gov (United States)

    Son, Seung-Wan; Lee, Jin-Seok; Kim, Hyeong-Geug; Kim, Dong-Woon; Ahn, Yo-Chan; Son, Chang-Gue

    2016-01-01

    Among sex hormones, estrogen is particularly well known to act as neuroprotective agent. Unlike estrogen, testosterone has not been well investigated in regard to its effects on the brain, especially under psychological stress. To investigate the role of testosterone in oxidative brain injuries under psychological stress, we adapted an orchiectomy and restraint stress model. BALB/c mice were subjected to either an orchiectomy or sham operation. After allowing 15 days for recovery, mice were re-divided into four groups according to exposure of restraint stress: sham, sham plus stress, orchiectomy, and orchiectomy plus stress. Serum testosterone was undetectable in orchiectomized groups and restraint-induced stress significantly reduced testosterone levels in sham plus stress group. The serum levels of corticosterone and adrenaline were notably elevated by restraint stress, and these elevated hormones were markedly augmented by orchiectomy. Two oxidative stressors and biomarkers for lipid and protein peroxidation were significantly increased in the cerebral cortex and hippocampus by restraint stress, while the reverse pattern was observed in antioxidant enzymes. These results were supported by histopathological findings, with 4-hydroxynonenal staining for oxidative injury and Fluoro-Jade B staining showing the degenerating neurons. The aforementioned patterns of oxidative injury were accelerated by orchiectomy. These findings strongly suggest the conclusion that testosterone exerts a protective effect against oxidative brain damage, especially under stressed conditions. Unlike estrogen, the effects of testosterone on the brain have not been thoroughly investigated. In order to investigate the role of testosterone in oxidative brain injuries under psychological stress, we adapted an orchiectomy and restraint stress model. Orchiectomy markedly augmented the restraint stress-induced elevation of serum corticosterone and adrenaline levels as well as oxidative alterations

  6. Mechanisms of mono- and poly-ubiquitination: Ubiquitination specificity depends on compatibility between the E2 catalytic core and amino acid residues proximal to the lysine

    Directory of Open Access Journals (Sweden)

    Sadowski Martin

    2010-08-01

    Full Text Available Abstract Ubiquitination involves the attachment of ubiquitin to lysine residues on substrate proteins or itself, which can result in protein monoubiquitination or polyubiquitination. Ubiquitin attachment to different lysine residues can generate diverse substrate-ubiquitin structures, targeting proteins to different fates. The mechanisms of lysine selection are not well understood. Ubiquitination by the largest group of E3 ligases, the RING-family E3 s, is catalyzed through co-operation between the non-catalytic ubiquitin-ligase (E3 and the ubiquitin-conjugating enzyme (E2, where the RING E3 binds the substrate and the E2 catalyzes ubiquitin transfer. Previous studies suggest that ubiquitination sites are selected by E3-mediated positioning of the lysine toward the E2 active site. Ultimately, at a catalytic level, ubiquitination of lysine residues within the substrate or ubiquitin occurs by nucleophilic attack of the lysine residue on the thioester bond linking the E2 catalytic cysteine to ubiquitin. One of the best studied RING E3/E2 complexes is the Skp1/Cul1/F box protein complex, SCFCdc4, and its cognate E2, Cdc34, which target the CDK inhibitor Sic1 for K48-linked polyubiquitination, leading to its proteasomal degradation. Our recent studies of this model system demonstrated that residues surrounding Sic1 lysines or lysine 48 in ubiquitin are critical for ubiquitination. This sequence-dependence is linked to evolutionarily conserved key residues in the catalytic region of Cdc34 and can determine if Sic1 is mono- or poly-ubiquitinated. Our studies indicate that amino acid determinants in the Cdc34 catalytic region and their compatibility to those surrounding acceptor lysine residues play important roles in lysine selection. This may represent a general mechanism in directing the mode of ubiquitination in E2 s.

  7. Superrotation of Earth’s Inner Core, Extraterrestrial Impacts, and the Effective Viscosity of Outer Core

    OpenAIRE

    Pirooz Mohazzabi; John D. Skalbeck

    2015-01-01

    The recently verified superrotation of Earth’s inner core is examined and a new model is presented which is based on the tidal despinning of the mantle and the viscosity of the outer core. The model also takes into account other damping mechanisms arising from the inner core superrotation such as magnetic and gravitational coupling as well as contribution from eddy viscosity in the outer core. The effective viscosity obtained in this model confirms a previously well constrained value of about...

  8. Animal MRI Core

    Data.gov (United States)

    Federal Laboratory Consortium — The Animal Magnetic Resonance Imaging (MRI) Core develops and optimizes MRI methods for cardiovascular imaging of mice and rats. The Core provides imaging expertise,...

  9. Ti2Al(C, N) Solid Solution Reinforcing TiAl-Based Composites: Evolution of a Core-Shell Structure, Interfaces, and Mechanical Properties.

    Science.gov (United States)

    Song, Xiaojie; Cui, Hongzhi; Han, Ye; Ding, Lei; Song, Qiang

    2018-05-16

    In this work, Ti 2 Al(C, N) solid solution with lamellar structure-enhanced TiAl matrix composites was synthesized by vacuum arc melting, using bulk g-C 3 N 4 , Ti, and Al powders as raw materials. The phases, microstructures, interfaces, and mechanical properties were investigated. MAX phase of Ti 2 Al(C, N) solid solution with lamellar structure was formed. During the melting process, first, C 3 N 4 reacted with Ti to form Ti(C, N) by Ti + C 3 N 4 → Ti(C, N). Then Ti 2 Al(C, N) was formed by a peritectic reaction of TiAl(l) + Ti(C, N)(s) → Ti 2 Al(C, N). C 3 N 4 is the single reactant that provides C and N simultaneously to final product of Ti 2 Al(C, N). The interfaces of TiAl//Ti 2 Al(C, N) and Ti 2 Al(C, N)//Ti(C, N) display perfect orientation relationships with low misfit values. The microhardness, compressive strength, and strain of best-performing TiAl-10 mol % Ti 2 Al(C, N) composite were improved by 45%, 55.7%, and 50% compared with the TiAl alloy, respectively. Uniformly distributed Ti 2 Al(C, N) and unreacted Ti(C, N) particles contributed to the grain refinement and reinforcement of the TiAl matrix. Laminated tearing, particle pull-out, and the crack-arresting of Ti 2 Al(C, N) are crucial for the improvement in compressive strength and plasticity of the composites.

  10. Effective applied moment in circumferential through-wall cracked pipes for leak-before-break evaluation considering pipe restraint effects

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yeji; Hwang, Il-Soon [Seoul National University, Seoul 08826 (Korea, Republic of); Oh, Young-Jin, E-mail: yjoh2@kepco-enc.com [KEPCO Engineering and Construction Co. Inc., Gimcheon 39660 (Korea, Republic of)

    2016-05-15

    Highlights: • Effective applied moment at pipe cracked section considering the pipe restraint effect. • Verification of the proposed evaluation methods using finite element analyses. • Applicability for distributed external load of the proposed methods. - Abstract: In the leak-before-break (LBB) design of nuclear power plants, crack opening displacement (COD) is an essential element for determining the length of the leakage size crack. Recent researches regarding the evaluation of COD have indicated that the current practice of the LBB evaluation without consideration of the pressure induced bending (PIB) restraint overestimates COD, which in turn gives non-conservative results. Under a free-ended boundary condition, however, the applied moment at cracked section also can be overestimated, which has conservative effects on LBB evaluation. Therefore, it is necessary to evaluate pipe restraint effects on the applied moment as well as on COD to keep the constancy. In this paper, an evaluation method for the effect of the PIB restraint on COD and an effective applied moment (=crack driving force) at cracked section was developed. Both the linear elastic and elastic–plastic behaviors of the crack were considered. By comparing the behaviors with 3-D finite element analysis results from earlier studies, it was confirmed that the proposed methods make accurate estimations of the PIB restraint effect on COD. Next, the applicability of the proposed method to other types of external loading conditions was examined.

  11. Sedation and physiologic response to manual restraint after intranasal administration of midazolam in Hispaniolan Amazon parrots (Amazona ventralis).

    Science.gov (United States)

    Mans, Christoph; Guzman, David Sanchez-Migallon; Lahner, Lesanna L; Paul-Murphy, Joanne; Sladky, Kurt K

    2012-09-01

    Administration of intranasal midazolam (2 mg/kg) was evaluated for sedation and effects on cloacal temperature, respiratory rate, and heart rate in manually restrained Hispaniolan Amazon parrots (Amazona ventralis). Adult parrots (n=9) were administered either midazolam (2 mg/kg) or an equal volume of saline solution intranasally before a 15-minute manual restraint in a complete crossover study. Respiratory rate and sedation scores were recorded before and during capture and during and after 15 minutes of manual restraint. Heart rate and cloacal temperature were recorded during manual restraint. After restraint, the parrots received intranasal flumazenil (0.05 mg/kg) or an equal volume of saline solution, and the recovery time was recorded. In those birds that received midazolam, sedation was observed within 3 minutes of administration, and vocalization, flight, and defense responses were significantly reduced during capture. During manual restraint, the mean rate of cloacal temperature increase was significantly slower and remained significantly lower in birds that received midazolam compared with controls. Mean respiratory rates were significantly lower for up to 12 minutes in parrots that received midazolam compared with those receiving saline solution. Flumazenil antagonized the effects of midazolam within 10 minutes. No overt clinical adverse effects to intranasal midazolam and flumazenil administration were observed. Further studies on the safety of intranasal midazolam and flumazenil in this species are warranted.

  12. Restraint training for awake functional brain scanning of rodents can cause long-lasting changes in pain and stress responses.

    Science.gov (United States)

    Low, Lucie A; Bauer, Lucy C; Pitcher, Mark H; Bushnell, M Catherine

    2016-08-01

    With the increased interest in longitudinal brain imaging of awake rodents, it is important to understand both the short-term and long-term effects of restraint on sensory and emotional processing in the brain. To understand the effects of repeated restraint on pain behaviors and stress responses, we modeled a restraint protocol similar to those used to habituate rodents for magnetic resonance imaging scanning, and studied sensory sensitivity and stress hormone responses over 5 days. To uncover lasting effects of training, we also looked at responses to the formalin pain test 2 weeks later. We found that while restraint causes acute increases in the stress hormone corticosterone, it can also cause lasting reductions in nociceptive behavior in the formalin test, coupled with heightened corticosterone levels and increased activation of the "nociceptive" central nucleus of the amygdala, as seen by Fos protein expression. These results suggest that short-term repeated restraint, similar to that used to habituate rats for awake functional brain scanning, could potentially cause long-lasting changes in physiological and brain responses to pain stimuli that are stress-related, and therefore could potentially confound the functional activation patterns seen in awake rodents in response to pain stimuli.

  13. Nurses' ethical reasoning in cases of physical restraint in acute elderly care: a qualitative study.

    Science.gov (United States)

    Goethals, Sabine; Dierckx de Casterlé, Bernadette; Gastmans, Chris

    2013-11-01

    In their practice, nurses make daily decisions that are ethically informed. An ethical decision is the result of a complex reasoning process based on knowledge and experience and driven by ethical values. Especially in acute elderly care and more specifically decisions concerning the use of physical restraint require a thoughtful deliberation of the different values at stake. Qualitative evidence concerning nurses' decision-making in cases of physical restraint provided important insights in the complexity of decision-making as a trajectory. However a nuanced and refined understanding of the reasoning process in terms of ethical values is still lacking. A qualitative interview design, inspired by the Grounded Theory approach, was carried out to explore nurses' reasoning process in terms of ethical values. We interviewed 21 acute geriatric nurses from 12 hospitals in different regions in Flanders, Belgium in the period October 2009-April 2011. The Qualitative Analysis Guide of Leuven was used to analyse interview data. Nurses' decision-making is characterized as an ethical deliberation process where different values are identified and where the process of balancing these values forms the essence of ethical deliberation. Ethical decision-making in cases of physical restraint implies that nurses have to choose which values receive priority in the process, which entails that not all values can be respected to the same degree. As a result, decision making can be experienced as difficult, even as a dilemma. Driven by the overwhelming goal of protecting physical integrity, nurses took into account the values of dignity and justice more implicitly and less dominantly.

  14. Interaction between repeated restraint stress and concomitant midazolam administration on sweet food ingestion in rats

    Directory of Open Access Journals (Sweden)

    Silveira P.P.

    2000-01-01

    Full Text Available Emotional changes can influence feeding behavior. Previous studies have shown that chronically stressed animals present increased ingestion of sweet food, an effect reversed by a single dose of diazepam administered before testing the animals. The aim of the present study was to evaluate the response of animals chronically treated with midazolam and/or submitted to repeated restraint stress upon the ingestion of sweet food. Male adult Wistar rats were divided into two groups: controls and exposed to restraint 1 h/day, 5 days/week for 40 days. Both groups were subdivided into two other groups treated or not with midazolam (0.06 mg/ml in their drinking water during the 40-day treatment. The animals were placed in a lighted area in the presence of 10 pellets of sweet food (Froot loops®. The number of ingested pellets was measured during a period of 3 min, in the presence or absence of fasting. The group chronically treated with midazolam alone presented increased ingestion when compared to control animals (control group: 2.0 ± 0.44 pellets and midazolam group: 3.60 ± 0.57 pellets. The group submitted to restraint stress presented an increased ingestion compared to controls (control group: 2.0 ± 0.44 pellets and stressed group: 4.18 ± 0.58 pellets. Chronically administered midazolam reduced the ingestion in stressed animals (stressed/water group: 4.18 ± 0.58 pellets; stressed/midazolam group: 3.2 ± 0.49 pellets. Thus, repeated stress increases appetite for sweet food independently of hunger and chronic administration of midazolam can decrease this behavioral effect.

  15. A restraint molecular dynamics and simulated annealing approach for protein homology modeling utilizing mean angles

    Directory of Open Access Journals (Sweden)

    Maurer Till

    2005-04-01

    Full Text Available Abstract Background We have developed the program PERMOL for semi-automated homology modeling of proteins. It is based on restrained molecular dynamics using a simulated annealing protocol in torsion angle space. As main restraints defining the optimal local geometry of the structure weighted mean dihedral angles and their standard deviations are used which are calculated with an algorithm described earlier by Döker et al. (1999, BBRC, 257, 348–350. The overall long-range contacts are established via a small number of distance restraints between atoms involved in hydrogen bonds and backbone atoms of conserved residues. Employing the restraints generated by PERMOL three-dimensional structures are obtained using standard molecular dynamics programs such as DYANA or CNS. Results To test this modeling approach it has been used for predicting the structure of the histidine-containing phosphocarrier protein HPr from E. coli and the structure of the human peroxisome proliferator activated receptor γ (Ppar γ. The divergence between the modeled HPr and the previously determined X-ray structure was comparable to the divergence between the X-ray structure and the published NMR structure. The modeled structure of Ppar γ was also very close to the previously solved X-ray structure with an RMSD of 0.262 nm for the backbone atoms. Conclusion In summary, we present a new method for homology modeling capable of producing high-quality structure models. An advantage of the method is that it can be used in combination with incomplete NMR data to obtain reasonable structure models in accordance with the experimental data.

  16. Aged rats are hypo-responsive to acute restraint: implications for psychosocial stress in aging

    Directory of Open Access Journals (Sweden)

    Heather M Buechel

    2014-02-01

    Full Text Available Cognitive processes associated with prefrontal cortex and hippocampus decline with age and are vulnerable to disruption by stress. The stress/ stress hormone/ allostatic load hypotheses of brain aging posit that brain aging, at least in part, is the manifestation of life-long stress exposure. In addition, as humans age, there is a profound increase in the incidence of new onset stressors, many of which are psychosocial (e.g., loss of job, death of spouse, social isolation, and aged humans are well-understood to be more vulnerable to the negative consequences of such new-onset chronic psychosocial stress events. However, the mechanistic underpinnings of this age-related shift in chronic psychosocial stress response, or the initial acute phase of that chronic response, have been less well-studied. Here, we separated young (3 mo. and aged (21 mo. male F344 rats into control and acute restraint (an animal model of psychosocial stress groups (n = 9-12/ group. We then assessed hippocampus-associated behavioral, electrophysiological, and transcriptional outcomes, as well as blood glucocorticoid and sleep architecture changes. Aged rats showed characteristic water maze, deep sleep, transcriptome, and synaptic sensitivity changes compared to young. Young and aged rats showed similar levels of distress during the three hour restraint, as well as highly significant increases in blood glucocorticoid levels 21 hours after restraint. However, young, but not aged, animals responded to stress exposure with water maze deficits, loss of deep sleep and hyperthermia. These results demonstrate that aged subjects are hypo-responsive to new-onset acute psychosocial stress, which may have negative consequences for long-term stress adaptation and suggest that age itself may act as a stressor occluding the influence of new onset stressors.

  17. Anti-stress effect of ethyl acetate soluble fraction of Morus alba in chronic restraint stress.

    Science.gov (United States)

    Nade, Vandana S; Yadav, Adhikrao V

    2010-09-01

    Restraint stress is a well-known method to induce chronic stress which leads to alterations in various behavioral and biochemical parameters. The present work was designed to study anti-stress effects of Morus alba in chronic restraint stress (RS)-induced perturbations in behavioral, biochemical and brain oxidative stress status. The stress was produced by restraining the animals inside an adjustable cylindrical plastic tube for 3 h once daily for ten consecutive days. The ethyl acetate soluble fraction of Morus alba (EASF) 25, 50, 100 mg/kg and diazepam (1 mg/kg) per day was administered 60 min prior to the stress procedure. The behavioral and biochemical parameters such as open field, cognitive dysfunction; leucocytes count; blood glucose and corticosteroid levels were determined. On day 10, the rats were sacrificed and biochemical assessment of superoxide dismutase (SOD), lipid peroxidation (LPO), catalase (CAT), and glutathione reductase (GSH) in whole rat brain were performed. Chronic restraint stress produced cognitive dysfunction, altered behavioral parameters, increased leucocytes count, SOD, LPO, glucose and corticosterone levels, with concomitant decrease in CAT and GSH activities. Gastric ulceration, adrenal gland and spleen weights were also used as the stress indices. All these RS induced perturbations were attenuated by EASF of Morus alba. The results of the study suggest that in addition to its classically established pharmacological activities, the plant also has immense potential as an anti-stress agent of great therapeutic relevance. This study indicates the beneficial role of Morus alba for the treatment of oxidative stress-induced disorders.

  18. Aged rats are hypo-responsive to acute restraint: implications for psychosocial stress in aging

    Science.gov (United States)

    Buechel, Heather M.; Popovic, Jelena; Staggs, Kendra; Anderson, Katie L.; Thibault, Olivier; Blalock, Eric M.

    2013-01-01

    Cognitive processes associated with prefrontal cortex and hippocampus decline with age and are vulnerable to disruption by stress. The stress/stress hormone/allostatic load hypotheses of brain aging posit that brain aging, at least in part, is the manifestation of life-long stress exposure. In addition, as humans age, there is a profound increase in the incidence of new onset stressors, many of which are psychosocial (e.g., loss of job, death of spouse, social isolation), and aged humans are well-understood to be more vulnerable to the negative consequences of such new-onset chronic psychosocial stress events. However, the mechanistic underpinnings of this age-related shift in chronic psychosocial stress response, or the initial acute phase of that chronic response, have been less well-studied. Here, we separated young (3 month) and aged (21 month) male F344 rats into control and acute restraint (an animal model of psychosocial stress) groups (n = 9–12/group). We then assessed hippocampus-associated behavioral, electrophysiological, and transcriptional outcomes, as well as blood glucocorticoid and sleep architecture changes. Aged rats showed characteristic water maze, deep sleep, transcriptome, and synaptic sensitivity changes compared to young. Young and aged rats showed similar levels of distress during the 3 h restraint, as well as highly significant increases in blood glucocorticoid levels 21 h after restraint. However, young, but not aged, animals responded to stress exposure with water maze deficits, loss of deep sleep and hyperthermia. These results demonstrate that aged subjects are hypo-responsive to new-onset acute psychosocial stress, which may have negative consequences for long-term stress adaptation and suggest that age itself may act as a stressor occluding the influence of new onset stressors. PMID:24575039

  19. The role of galanin system in modulating depression, anxiety, and addiction-like behaviors after chronic restraint stress.

    Science.gov (United States)

    Zhao, X; Seese, R R; Yun, K; Peng, T; Wang, Z

    2013-08-29

    There is high comorbidity between stress-related psychiatric disorders and addiction, suggesting they may share one or more common neurobiological mechanisms. Because of its role in both depressive and addictive behaviors, the galanin system is a strong candidate for such a mechanism. In this study, we tested if galanin and its receptors are involved in stress-associated behaviors and drug addiction. Mice were exposed to 21 days of chronic restraint stress (CRS); subsequently, mRNA levels of galanin, galanin receptors (GalRs), the rate-limiting enzymes for the synthesis of monoamines, and monoamine autoreceptors were measured in the nucleus accumbens by a quantitative real-time polymerase chain reaction. Moreover, we tested the effects of this stress on morphine-induced addictive behaviors. We found that CRS induced anxiety and depression-like behaviors, impaired the formation and facilitated the extinction process in morphine-induced conditioned place preference (CPP), and also blocked morphine-induced behavioral sensitization. These behavioral results were accompanied by a CRS-dependent increase in the mRNA expression of galanin, GalR1, tyrosine hydroxylase (TH), tryptophan hydroxylase 2, and 5-HT1B receptor. Interestingly, treatment with a commonly used antidepressant, fluoxetine, normalized the CRS-induced behavioral changes based on reversing the higher expression of galanin and TH while increasing the expression of GalR2 and α2A-adrenceptor. These results indicate that activating the galanin system, with corresponding changes to noradrenergic systems, following chronic stress may modulate stress-associated behaviors and opiate addiction. Our findings suggest that galanin and GalRs are worthy of further exploration as potential therapeutic targets to treat stress-related disorders and drug addiction. Copyright © 2013 IBRO. All rights reserved.

  20. Effect of Fluoxetine on the Hippocampus of Wistar Albino Rats in Cold Restraint Stress Model.

    Science.gov (United States)

    Jayakumar, Saikarthik; Raghunath, Gunapriya; Ilango, Saraswathi; Vijayakumar, J; Vijayaraghavan, R

    2017-06-01

    Stress has been known to be a potential modulator of learning and memory. Long term stress can lead to depression. Fluoxetine is a selective serotonin reuptake inhibitor group of drug used in the treatment of depression. The present study was conducted to evaluate the potential of Fluoxetine on cold restraint induced stress in the hippocampus of Wistar rats. A total of 18 male wistar albino rats were divided randomly into three groups (n=6). Group 1 was the control group which were kept in normal laboratory conditions. Group 2 was the negative control group which were given cold restraint stress for period of four weeks. Group 3 was the experimental group, where the animals were pretreated with fluoxetine 10 mg/kg for a period of one week followed by cold restraint stress for 30 minutes and cotreated with fluoxetine 10 mg/kg for a period of four weeks. The whole study was done for a period of five weeks followed by behavioural studies and subsequently sacrificed with removal of brain for various histological, Immunohistochemical (IHC), neurochemical and antioxidant analysis. The values were expressed as Mean±SEM. One-way analysis of variance followed by Tukey's multiple comparisons test was used for the comparison of means. A probability of 0.05 and less was taken as statistically significant using Prism Graphpad software version 6.01. The results show there was significant improvement in the Morris water maze test after treatment with fluoxetine in Group 2. Similar results were also noted in the levels of neurotransmitters and antioxidant levels in brain and also in the number of cells counted in IHC and histological studies by H&E when Group 3 was compared with Group 2. The treatment reversed the damage in Group 2 which was comparable with the control group. The results revealed that administration of fluoxetine 10 mg/kg given orally has a potential antistressor effect by improving the neurogenic and neuroprotective effect on the cold restraint stress induced