Investigation of primary cooling water chemistry following the partial meltdown of Pu-Be neutron source in Tehran Research Reactor Core (TRR)

Energy Technology Data Exchange (ETDEWEB)

Aghoyeh, Reza Gholizadeh [School of Research and Development of Nuclear Reactors and Accelerators, Nuclear Science and Technology Research Institute (NSTRI), Atomic Energy Organization of Iran (AEOI), P.O. Box: 14155-1339, Tehran (Iran, Islamic Republic of); Khalafi, Hossein, E-mail: hkhalafi@aeoi.org.i [School of Research and Development of Nuclear Reactors and Accelerators, Nuclear Science and Technology Research Institute (NSTRI), Atomic Energy Organization of Iran (AEOI), P.O. Box: 14155-1339, Tehran (Iran, Islamic Republic of)

2011-03-15

Research highlights: Effect of Pu-Be neutron source meltdown in core on reactor water chemistry. Water chemistry of primary cooling before, during and after of above incident was compared. Training importance. Management of nuclear incident and accident. - Abstract: Effect of Pu-Be neutron source meltdown in core on reactor water chemistry was main aim of this study. Leaving the neutron source in the core after reactor power exceeds a few hundred Watts was the main reason for its partial meltdown. Water chemistry of primary cooling before, during and after of above incident was compared. Activity of some radio-nuclides such as Ba-140, La-140, I-131, I-132, Te-132 and Xe-135 increased. Other radio-nuclides such as Nd-147, Xe-133, Sr-91, I-133 and I-135 are also detected which were not existed before this incident.

How to arrest a core meltdown accident (doing nothing)

International Nuclear Information System (INIS)

Baron, Jorge H.

2000-01-01

In the eventual situation of a severe accident in a nuclear reactor, the molten core is able to relocate inside the pressure vessel. This may lead to the vessel failure, due to the thermal attack of the molten core (at approximation of 3000K) on the vessel steel wall. The vessel failure implies the failure of a very important barrier that contains the radioactive materials generated during the reactor operation, with a significant risk of producing high radiation doses both on operators and on the public. It is expected, for the new generation of nuclear reactors, that these will be required to withstand (by design) a core melt down accident, without the need for an immediate evacuation of the surrounding population. In this line, the use of a totally passive system is postulated, which fulfills the objective of containing the molten core inside the pressure vessel, at low temperature (approximation 1200K) precluding its failure. The conceptual design of a passive in-vessel core catcher is presented in this paper, built up of zinc, and designed for the CAREM-25 nuclear power plant. (author)

Method and device for catching reactor core melt-down masses in hypothetical accidents of nuclear power plants

International Nuclear Information System (INIS)

Morlock, G.; Wiesemes, J.; Bachner, D.

1977-01-01

The device is to receive the afterheat of the molten core and in this way to prevent afterflow of coolant and a new criticality. A tank below the reactor pressure vessel, with the proper diameter, contains a store of salt or a salt mixture suitable to receive the afterheat of a core melt-down as heat of fusion or conversion. Above the salt, there is a layer of thermoplastics or of a material forming a hardening foam. Coolant eventually continuing to flow out is separated from the core melt by this barrier layer, and thus the build-up of high steam pressures is prevented. Neutron-absorbing materials, like boron salts mixed to the salts, as well as a subdivision of the salt surface, e.g. by means of canalizing firebricks, prevent the formation of new criticality. Further installations within the tank, like pipings or channels, permit the introduction of water after cooling down of the core or salt melt-down mass and to wash out the brine with all radioactive and other constituents for transport to reprocessing or ultimate storage. (HP) [de

A critical experimental study of integral physics parameters in simulated LMFBR meltdown cores

International Nuclear Information System (INIS)

Bhattacharyya, S.K.; Wade, D.C.; Bucher, R.G.; Smith, D.M.; McKnight, R.D.; Lesage, L.G.

1978-01-01

Integral physics parameters of several representative, idealized meltdown LMFBR configurations were measured in mockup critical assemblies on the ZPR-9 reactor at Argonne National Laboratory. The experiments were designed to provide data for the validation of analytical methods used in the neutronics part of LMFBR accident analysis. Large core distortions were introduced in these experiments (involving 18.5% core volume) and the reactivity worths of configuration changes were determined. The neutronics parameters measured in the various configurations showed large changes upon core distortion. Both diffusion theory and transport theory methods were shown to mispredict the experimental configuration eigenvalues. In addition, diffusion theory methods were shown to result in a non-conservative misprediction of the experimental configuration change worths. (author)

On-site releases of noble gases and iodine in the event of core meltdown in a swimming pool reactor

International Nuclear Information System (INIS)

Montaignac, E. de.

1976-10-01

Research aimed at defining a standard model accident for swimming pool type reactors, has led to the adoption to the so-called BORAX accident which involves complete meltdown of the reactor core. This type of accident-an accident related to dimensional problems- is useful for calculations concerning reactor components which have to withstand the mechanical forces resulting from the accident. A study of the radiobiological consequences of this type of accident, involving the entire reactor core, required research to determine as accurately as possible how the iodine, noble gases and solid fission products are distributed between the melted core and the site. The joint document in the annexure served as the basis for discussion at the meeting (BEVS/SESR) on 9th March 1973, at which the SESR set the standard parameter values to be used for estimating fission product distributions on the site. (author)

Numerical simulation of passive heat removal under severe core meltdown scenario in a sodium cooled fast reactor

Energy Technology Data Exchange (ETDEWEB)

David, Dijo K.; Mangarjuna Rao, P., E-mail: pmr@igcar.gov.in; Nashine, B.K.; Selvaraj, P.; Chellapandi, P.

2015-09-15

hydraulics of Post Accident Heat Removal (PAHR) towards extending the functionality of core catcher for handling Whole Core Meltdown Accident (WCA) scenarios in future SFRs.

On the failure modes of alternative containment designs following postulated core meltdown

International Nuclear Information System (INIS)

Chan, C.K.; Knee, H.E.; Okrent, D.

1977-01-01

The containment response to a postulated core meltdown accident in a PWR ice condenser containment, a BWR Mark III containment and a BWR non-inerted Mark I containment has been examined to see if the WASH-1400 containment failure mode judgement for the Surry large, dry containment and the Peach Bottom Mark I inerted-containment are likely to be appropriate for these alternative containment plant designs. For the PWR, the representative accident chosen for the analysis is a large cold leg break accompanied by a loss of all electric power while the BWR respresentative event chosen is a recirculation line break without adequate core cooling function. Two containment event paths are studied for each of these two cases, depending on whether or not containment vapor suppression function is assumed to be available. Both the core and the containment pressure and temperature response to the accident events are computed for the four time intervals which characterize (a) blowdown of the pipe break, (b) core melt, (c) vessel melt-through, and (d) containment foundation penetration. The calculations are based on a best esimate of the most probable sequence, but certain phenomena and events were followed down multiple tracks. It appears that the non-inerted Mark I containment is not so vulnerable to overpressurization from hydrogen burning as the Mark III; however, acceptable temperatures may be exceeded. (Auth.)

Event course analysis of core disruptive accidents; Ereignisablaufanalyse kernzerstoerender Unfaelle

Energy Technology Data Exchange (ETDEWEB)

Hering, W.; Homann, C.; Sengpiel, W.; Struwe, D.; Messainguiral, C.

1995-08-01

The theortical studies of the behavior of a PWR core in a meltdown accident are focused on hydrogen release, materials redistribution in the core area including forming of an oxide melt pool, quantity of melt and its composition, and temperatures attained by the RPV internals (esp. in the upper plenum) during the accident up to the time of melt relocation into the lower plenum. The calculations are done by the SCDAP/RELAP5 code. For its validation selected CORA results and Phebus FPTO results have been used. (orig.)

Effects of methodic deficiencies on the quantification of core meltdown frequency

International Nuclear Information System (INIS)

Hahn, L.

1984-01-01

The application of sequence of events and fault tree analyses for the assessment of the core meltdown frequency raises problems, most of which can be classified under: - Completeness and representativeness of sequences and cuases of events - Modelling of conditional outages (common-mode outages) - Modelling of human behaviour - Reliability data and models. All of the weak points of the German Risk Study related to these problems which are mentioned by the Ecological Institute show a tendency to underestimate the core meltdown frequency by a factor at least 6. (RF) [de

Method of reducing the hazard which may occur as a consequence of a reactor core meltdown

International Nuclear Information System (INIS)

Donne, M.D.; Dorner, S.; Schumacher, G.

1978-01-01

The core melt resulting from a meltdown accident of a GFB, LWR or LMFRR is collected by a core catcher from graphite placed below the core. The core melt is penetrating step by step into a borate store in the collecting vessel and is dissolving in it. Therefore the borate at the same time will absorb the decay heat. In order to remove the solidified and cooled down melted mass water is applied eliminating the borate. The remaining oxide state of the powdery core is sucked off again from the core catcher together with the water. The borate store (e.g. alkali borate) itself consists of separate layers with shaped parts, the coverings of which are made of steel, iron, cast iron, nickel, iron or nickel alloys, ceramic material or glass. (DG) [de

Method of reducing the hazard which may occur as a consequence of a reactor core meltdown

International Nuclear Information System (INIS)

Donne, M.D.; Dorner, S.; Schumacher, G.

1985-01-01

The core melt resulting from a meltdown accident of a GFB, LWR or LMFRR is collected by a core catcher from graphite placed below the core. The core melt is penetrating step by step into a borate store in the collecting vessel and is dissolving in it. Therefore the borate at the same time will absorb the decay heat. In order to remove the solidified and cooled down melted mass water is applied eliminating the borate. The remaining oxide states of the powdery core is sucked off again from the core catcher together with the water. The borate store (e.g. alkali borate) itself consists of separate layers with shaped parts, the coverings of which are made of steel, iron, cast iron, nickel, iron or nickel alloys, ceramic material or glass. (orig./PW)

Study of diluting and absorber materials to control the reactivity during a postulated core meltdown accident in generation IV reactors

International Nuclear Information System (INIS)

Plevacova, Kamila

2010-01-01

In order to limit the consequences of a hypothetical core meltdown accident in Generation IV Sodium Fast Reactors, absorber materials in or near the core, such as boron carbide B 4 C, and diluting materials in the core catcher will be used to prevent recriticality within the mixture of molten oxide fuel and molten structures called corium. The aim of the PhD thesis was to select materials of both types and to understand their behaviour during their interaction with corium, from chemical and thermodynamic points of view. Concerning B 4 C, thermodynamic calculations and experiments agree with the formation of two immiscible phases at high temperature in the B 4 C - UO 2 system: one oxide and one boride. This separation of phases can reduce the efficiency of the neutrons absorption inside the molten fuel contained in the oxide phase. Moreover, volatilization of a part of the boron element can occur. According to these results, the necessary quantity of B 4 C to be introduced should be reconsidered for postulated severe accident sequence. Other solution could be the use of Eu 2 O 3 or HfO 2 as absorber material. These oxides form a solid solution with the oxide fuel. Concerning the diluting materials, mixed oxides Al 2 O 3 - HfO 2 and Al 2 O 3 - Eu 2 O 3 were preselected. These systems being completely unknown to date at high temperature in association with UO 2 , first points on the corresponding ternary phase diagrams were researched. Contrary to Al 2 O 3 - Eu 2 O 3 - UO 2 system, the Al 2 O 3 - HfO 2 - UO 2 mixture presents only one eutectic and thus only one solidification path which makes easier forecasting the behaviour of corium in the core catcher. (author)

Concepts for passive heat removal and filtration systems under core meltdown conditions

International Nuclear Information System (INIS)

Wilhelm, J.G.; Neitzel, H.-J.

1993-01-01

The objective of the new containment concept being developed by KfK is the complete passive enclosure of a power reactor after a core meltdown accident by means of a solid containment structure and passive removal of the decay heat. This is to be accomplished by cooling the containment walls with ambient air, with thermoconvection as the driving force. The concept of the containment is described. Data are given of the heat removal and the requirements for filtration of the exhaust air, which is contaminated due to the leak rate assumed for the inner containment. The concept for the filter system is described. Various solutions for reduction of the large volumetric flow to be filtered are discussed. 3 refs., 8 figs

Synthesis of the IRSN report on the topic of water way answers to implement in case of accident with core meltdown occurring on operating pressurized water nuclear reactors

International Nuclear Information System (INIS)

2009-06-01

This report briefly discusses the efficiency of technical measures adopted for the implementation of water ways as answers to an accident with core meltdown in operating pressurized water nuclear reactors. While mentioning the importance of the hydro-geological characteristics of the various sites, the IRSN asks EDF to plan and implement means to prevent any rejection through water ways for some of these sites, to investigate the possibility of building a geotechnical enclosure, to define a storing-control-treatment-rejection chain which would guarantee an efficient management of the water to be pumped, to study retention phenomena for strontium and caesium isotopes in sands and gravels

ASTRID core: Design objectives, design approach, and R&D in support

International Nuclear Information System (INIS)

Mignot, G.; Devictor, N.

2012-01-01

ASTRID core design is mainly guided by safety objectives: 1. Prevention of the core meltdown accident: To prevent meltdown accidents: - by a natural behavior of the core and the reactor (no actuation of the two shutdown systems); - with adding passive complementary systems if natural behavior is not sufficient for some transient cases. 2. Mitigation of the fusion accident: To garantee that core fusion accidents don’t lead to significant mechanical energy release, whatever initiator event: - by a natural core behavior; - with adding specific mitigation dispositions in case of natural behavior is not suffficient

Thermohydraulics in a high-temperature gas-cooled reactor primary loop during early phases of unrestricted core-heatup accidents

International Nuclear Information System (INIS)

Kroeger, P.G.; Colman, J.; Hsu, C.J.

1983-01-01

In High Temperature Gas Cooled Reactor (HTGR) siting considerations, the Unrestricted Core Heatup Accidents (UCHA) are considered as accidents of highest consequence, corresponding to core meltdown accidents in light water reactors. Initiation of such accidents can be, for instance, due to station blackout, resulting in scram and loss of all main loop forced circulation, with none of the core auxiliary cooling system loops being started. The result is a slow but continuing core heatup, extending over days. During the initial phases of such UCHA scenarios, the primary loop remains pressurized, with the system pressure slowly increasing until the relief valve setpoint is reached. The major objectives of the work described here were to determine times to depressurization as well as approximate loop component temperatures up to depressurization

Annual meeting on nuclear technology 1982. Technical meeting: Possibilities and effects of serious reactor accidents

International Nuclear Information System (INIS)

1982-01-01

A critical examination of the forecast of a design basis accident, the view of the Sandia National Laboratory on the probability of a steam explosion after a core meltdown accident is comparison with WASH-1400, the possibilities of interactions with the containment structure and fission product release, as well as the influences for the assessment of risk in Germany taken from the analysis of core meltdown accidents are dealt with in these papers. (DG) [de

Nuclear reactor core catcher

International Nuclear Information System (INIS)

1977-01-01

A nuclear reactor core catcher is described for containing debris resulting from an accident causing core meltdown and which incorporates a method of cooling the debris by the circulation of a liquid coolant. (U.K.)

Severe accident considerations for modern KWU-PWR plants

International Nuclear Information System (INIS)

Eyink, J.

1987-01-01

In assumption of severe accident on modern KWU-PWR plants the author discusses on the: selection of core meltdown sequences, course of the accident, containment behaviour and source terms for fission products release to the environment

Core failure accident pathways and ways to control it

International Nuclear Information System (INIS)

Mayinger, F.

1982-01-01

In the German Risk Study accidents are assumed to result in core meltdown whenever the criteria spelt out in the guidelines of the Advisory Committee on Reactor Safeguards are no longer met. This assumption must be seen in the light of an earlier state of the art in which no detailed information could be obtained about intermediate stages in emergency core cooling systems working according to permit up to the complete failure of all heat removal systems. However, experimental studies and theoretical analyses conducted over the past few years have advanced the state of the art such that it is now possible to predict with considerably more physical reality the behavior of a core in a loss-of-coolant accident. These findings are not only based on calculations, but also on the results of experiments in large facilities allowing direct comparisons to be made with conditions in nuclear power plants. Studies of the effects of systems failures both in major leakages and in the small leakages regarded to be much more dangerous show much more favorable conditions with respect to core coolability than had to be anticipated on the basis of earlier assumptions. This also implies that it would neither be necessary nor meaningful to reinforce emergency core cooling systems. Instead, it is much more important, besides having technically highly qualified and thoroughly trained operating crews, to inform those crews reliably of the hydrodynamic and thermodynamic state of the primary system, especially the core. (orig.) [de

Numerical investigation on turbulent natural convection in partially connected cylindrical enclosures for analysing SFR safety under core meltdown scenario

International Nuclear Information System (INIS)

David, Dijo K.; Mangarjuna Rao, P.; Nashine, B.K.; Selvaraj, P.

2015-01-01

Under the unlikely event of severe core meltdown accident in pool type SFR, the molten core materials may rupture the grid plate which supports the fuel subassemblies and it can get relocated in to the lower pool. These debris may eventually settle on the debris collector (i.e., core catcher) installed above the bottom wall of the lower pool. The bed thus formed generates heat due to radioactive decay which has to be passively removed for maintaining the structural integrity of main vessel. By means of natural convection, the heat generated in the debris bed will be transferred to the top pool where the heat sink (i.e., Decay heat exchanger (DHX)) is installed. Heat transfer to the DHX (which is a part of safety grade decay heat removal system) can take place through the opening created in the grid plate which connects the two liquid pools (i.e., the top pool and the lower pool). Heat transfer can also take place through the lateral wall of the lower cylindrical pool to the side pool and eventually to the top pool, and thus to the DHX. This study numerically investigates the effectiveness of heat transfer between lower pool and top pool during PARR by considering them as partially connected cylindrical enclosures. The governing equations have been numerically solved using finite volume method in cylindrical co-ordinates using SIMPLE algorithm. Turbulence has been modeled using k-ω model and the model is validated against benchmark problems of natural convection found in literature. The effect of parameters such as the heat generation rate in the bed and the size of the grid plate opening are evaluated. Also PAHR in SFR pool is modeled using an axi-symmetric model to fund out the influence of grid plate opening on heat removal from core catcher. The results obtained are useful for improving the cooling capability of in-vessel tray type core catcher for handling the whole core meltdown scenarios in SFR. (author)

Assessment of uncertainties in core melt phenomenology and their impact on risk at the Z/IP facilities

International Nuclear Information System (INIS)

Pratt, W.T.; Ludewig, H.; Bari, R.A.; Meyer, J.F.

1983-01-01

An evaluation of core meltdown accidents in the Z/IP facilities has been performed. Containment event trees have been developed to relate the progression of a given accident to various potential containment building failure modes. An extensive uncertainty analysis related to core melt phenomenology has been performed. A major conclusion of the study is that large variations in parameters associated with major phenomenological uncertainties have a relatively minor impact on risk when external initiators are considered. This is due to the inherent capability fo the Z/IP containment buildings to contain a wide range of core meltdown accidents. 12 references, 2 tables

Scoping Analysis on Core Disruptive Accident in PGSFR (2015 Results)

Energy Technology Data Exchange (ETDEWEB)

Lee, Seung Won; Chang, Won-Pyo; Ha, Kwi-Seok; Ahn, Sang June; Kang, Seok Hun; Choi, Chi-Woong; Lee, Kwi Lim; Jeong, Jae-Ho; Kim, Jin Su; Jeong, Taekyeong [KAERI, Daejeon (Korea, Republic of)

2016-05-15

In general, the severe accident is classified by three phases. The first phase is the initiation (pre-disassembly) phase that occurs the gradual core meltdown from accident initiation to the point of neutronic shutdown with an intact geometry. The second phase is the transition phase that happens the fuel transition from a solid to a liquid phase. Fuel and cladding can melt to form a molten pool and core can boil, then criticality conditions can recur. The third phase is the disassembly phase. In other words, this phase is Core Disruptive Accident (CDA). Power excursion is followed until the core is disassembled in this phase. In the early considerations of Liquid Metal Fast Breeder Reactor (LMFBR) energetics, the term Hypothetical Core Disruptive Accidents (HCDAs) was in common use. This was not only to connote the extremely low probability of initiation of such accidents, but also the tentative nature of our understanding of their behavior and resulting consequences. A numerical analysis is conducted to estimate the energy release, pressure behavior and core expansion behavior induced by CDA of PGSFR using CDA-ER and CDA-CEME codes. Conservatively, the calculated results of energy release and pressure behavior induced by CDA without Doppler effect in PGSFR when whole cores were melted (100 $/s) were 7.844 GJ and 4.845 GPa, respectively. With Doppler effect, the analyzed maximum energy release and pressure were 6.696 GJ and 3.449 GPa, respectively. The calculated results of the core expansion behavior during 0.015 seconds after the explosion without Doppler effect in PGSFR when whole cores were melted (100 $/s) were as follows: The total energy is calculated to be 1.87 GJ. At 0.01 s, the kinetic energy of the sodium is 1.85 GJ, while the expansion work and internal energy of the bubble are 19.7 MJ and 0.98 J, respectively. With Doppler effect, the total energy is calculated to be 1.33 GJ. At 0.01 s, the kinetic energy of the sodium is 1.31 GJ, while the expansion

Comparison of computer codes relative to the aerosol behavior in the reactor containment building during severe core damage accidents in a PWR

International Nuclear Information System (INIS)

Fermandjian, J.; Bunz, H.; Dunbar, I.; Gauvain, J.; Ricchena, R.

1986-01-01

The present study concerns a comparative exercise, performed within the framework of the Commission of the European Communities, of the computer codes (AEROSIM-M, UK; AEROSOLS/B1, France; CORRAL-2, CEC and NAUA Mod5, Germany) used in order to assess the aerosol behavior in the reactor containment building during severe core damage accidents in a PWR. Topics considered in this paper include aerosols, containment buildings, reactor safety, fission product release, reactor cores, meltdown, and monitoring

The consequences from liquid pathways after a reactor meltdown accident

International Nuclear Information System (INIS)

Niemczyk, S.J.; Adams, K.G.; Murfin, W.B.; Ritchie, L.T.; Eppel, E.W.; Johnson, J.D.

1981-06-01

The potential radiological impact of a core-melt accident on the human population has been investigated. In particular, the radiation dose received from radioactivity which could reach the population via liquid pathways has been considered. Radioactivity could be released directly to the hydrosphere after a core-melt accident as a result of melt-through of the containment basemat followed by any of three processes: (1) leaching of the melt debris; 2 escape of sumpwater through the hole formed by the melt (or from passage out of the containment by an alternate route); and 3) depressurization of the containment atmosphere through the melt hole. The three types of releases would differ primarily in their rates, their magnitudes and their radioactive compositions. Both the containment atmosphere and the sumpwater releases would occur relatively rapidly. However, most of the radionuclides present in these two releases in substantial quantities would be expected to be rather short-lived. Therefore, such releases could have a significant impact at a specific site only if the travel times of the important radionuclides to the human population were small. In contrast, leaching of radionuclides from the melt debris would be expected to occur relatively slowly. Most of the long-lived isotopes would be expected to be found primarily in the melt debris. Consequently, even though this release occurred relatively slowly, the impact could still be significant. In contrast to the situation for releases to the atmosphere, accidents corresponding to the most probable RSS (Reactor Safety Study) meltdown categories would result in the largest releases to the hydrosphere. Furthermore, substantial amounts of radioactivity would generally be expected to be released to the hydrosphere during any meltdown accident involving complete melt-through of the containment basemat. On the basis of subsurface hydrologies alone, sites range from those that essentially preclude any impacts to the human

Use of decision trees for evaluating severe accident management strategies in nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Jae, Moosung [Hanyang Univ., Seoul (Korea, Republic of). Dept. of Nuclerar Engineering; Lee, Yongjin; Jerng, Dong Wook [Chung-Ang Univ., Seoul (Korea, Republic of). School of Energy Systems Engineering

2016-07-15

Accident management strategies are defined to innovative actions taken by plant operators to prevent core damage or to maintain the sound containment integrity. Such actions minimize the chance of offsite radioactive substance leaks that lead to and intensify core damage under power plant accident conditions. Accident management extends the concept of Defense in Depth against core meltdown accidents. In pressurized water reactors, emergency operating procedures are performed to extend the core cooling time. The effectiveness of Severe Accident Management Guidance (SAMG) became an important issue. Severe accident management strategies are evaluated with a methodology utilizing the decision tree technique.

The consequences from liquid pathways after a reactor meltdown accident

Energy Technology Data Exchange (ETDEWEB)

Niemczyk, S J; Adams, K G; Murfin, W B; Ritchie, L T; Eppel, E W; Johnson, J D

1981-06-01

The potential radiological impact of a core-melt accident on the human population has been investigated. In particular, the radiation dose received from radioactivity which could reach the population via liquid pathways has been considered. Radioactivity could be released directly to the hydrosphere after a core-melt accident as a result of melt-through of the containment basemat followed by any of three processes: (1) leaching of the melt debris; 2 escape of sumpwater through the hole formed by the melt (or from passage out of the containment by an alternate route); and 3) depressurization of the containment atmosphere through the melt hole. The three types of releases would differ primarily in their rates, their magnitudes and their radioactive compositions. Both the containment atmosphere and the sumpwater releases would occur relatively rapidly. However, most of the radionuclides present in these two releases in substantial quantities would be expected to be rather short-lived. Therefore, such releases could have a significant impact at a specific site only if the travel times of the important radionuclides to the human population were small. In contrast, leaching of radionuclides from the melt debris would be expected to occur relatively slowly. Most of the long-lived isotopes would be expected to be found primarily in the melt debris. Consequently, even though this release occurred relatively slowly, the impact could still be significant. In contrast to the situation for releases to the atmosphere, accidents corresponding to the most probable RSS (Reactor Safety Study) meltdown categories would result in the largest releases to the hydrosphere. Furthermore, substantial amounts of radioactivity would generally be expected to be released to the hydrosphere during any meltdown accident involving complete melt-through of the containment basemat. On the basis of subsurface hydrologies alone, sites range from those that essentially preclude any impacts to the human

Transuranium contamination in BWRs after fuel accidents and its impact on decommissioning exposures and costs

Energy Technology Data Exchange (ETDEWEB)

Lundgren, K.

1996-12-01

The theme of the present study is to quantify the amount of transuranium activity in different parts of the plant after various fuel accidents, and which impact such contamination has on radiation exposure and costs for decommissioning the plant. The consequences of four different accident degrees have been treated: Common fuel failures, e.g. in line with recent experiences from Swedish BWRs; Fuel channel obstruction resulting in partial melting of one fuel assembly; Total loss of electric power resulting in partial meltdown of the core, but with primary circuit intact preventing a massive contamination of the containment; A LOCA followed by a core meltdown and melting and penetration of the reactor pressure vessel. The amount of transuranium activity distributed, the form of this activity and the plant contamination are evaluated for these accidents. The costs and exposures have been split up on cleanup activities after the accident and decommissioning. 75 refs.

Transuranium contamination in BWRs after fuel accidents and its impact on decommissioning exposures and costs

International Nuclear Information System (INIS)

Lundgren, K.

1996-12-01

The theme of the present study is to quantify the amount of transuranium activity in different parts of the plant after various fuel accidents, and which impact such contamination has on radiation exposure and costs for decommissioning the plant. The consequences of four different accident degrees have been treated: Common fuel failures, e.g. in line with recent experiences from Swedish BWRs; Fuel channel obstruction resulting in partial melting of one fuel assembly; Total loss of electric power resulting in partial meltdown of the core, but with primary circuit intact preventing a massive contamination of the containment; A LOCA followed by a core meltdown and melting and penetration of the reactor pressure vessel. The amount of transuranium activity distributed, the form of this activity and the plant contamination are evaluated for these accidents. The costs and exposures have been split up on cleanup activities after the accident and decommissioning. 75 refs

Applicability of Phebus FP results to severe accident safety evaluations and management measures

International Nuclear Information System (INIS)

Schwarz, M.; Clement, B.; Jones, A.V.

2001-01-01

The international Phebus FP (Fission Product) programme is the largest research programme in the world investigating core degradation and radioactive product release should a core meltdown accident occur in a light water reactor plant. Three integral experiments have already been performed. The experimental database obtained so far contains a wealth of information to validate the computer codes used for safety and accident management assessment

Study of an hypothetical reactor meltdown accident for a 50 MW sub(th) fast reactor

International Nuclear Information System (INIS)

Azevedo, E.M. de.

1983-01-01

A melhodology for determining the energy released in hypothetical reactor meltdown accidents is presented. A numerical code was developed based upon the Nicholson method for a uniform and homogeneous reactor with spherical geometry. A comparative study with other know programs in the literature which use better approximations for small energy released, shows that the methodology used were compatible with those under comparison. Besides the influence of some parameters on the energy released, such as the initial power level and the prompt neutron lifetime was studied under this metodology and its result exhibitted. The Doppler effect was also analyzed and its influence on the energy released has been emphasized. (Author) [pt

Risk reduction of core-melt accidents in advaned CAPRA burner cores

International Nuclear Information System (INIS)

Maschek, W.; Struwe, D.; Eigemann, M.

1997-01-01

As part of the CAPRA Program (Consommation Accrue de Plutonium dans les RApides) the feasibility of fast reactors is investigated to burn plutonium and also to destruct minor actinides. The design of CAPRA cores shows significant differences compared to conventional cores. Especially the high Pu-enrichment has an important influence on the core melt-down behavior and the associated recriticality risk. To cope with this risk, inherent design features and special measures/devices are investigated for their potential of early fuel discharge to reduce the criticality of the reactor core. An assessment of such measures/devices is given and experimental needs are formulated. 11 refs., 5 figs

How to arrest a core meltdown accident (doing nothing); Como detener un accidente con fusion de nucleo (sin hacer nada)

Energy Technology Data Exchange (ETDEWEB)

Baron, Jorge H [Autoridad Regulatoria Nuclear, Buenos Aires (Argentina)

2000-07-01

In the eventual situation of a severe accident in a nuclear reactor, the molten core is able to relocate inside the pressure vessel. This may lead to the vessel failure, due to the thermal attack of the molten core (at approximation of 3000K) on the vessel steel wall. The vessel failure implies the failure of a very important barrier that contains the radioactive materials generated during the reactor operation, with a significant risk of producing high radiation doses both on operators and on the public. It is expected, for the new generation of nuclear reactors, that these will be required to withstand (by design) a core melt down accident, without the need for an immediate evacuation of the surrounding population. In this line, the use of a totally passive system is postulated, which fulfills the objective of containing the molten core inside the pressure vessel, at low temperature (approximation 1200K) precluding its failure. The conceptual design of a passive in-vessel core catcher is presented in this paper, built up of zinc, and designed for the CAREM-25 nuclear power plant. (author)

Caesium-rich micro-particles: A window into the meltdown events at the Fukushima Daiichi Nuclear Power Plant

Science.gov (United States)

Furuki, Genki; Imoto, Junpei; Ochiai, Asumi; Yamasaki, Shinya; Nanba, Kenji; Ohnuki, Toshihiko; Grambow, Bernd; Ewing, Rodney C.; Utsunomiya, Satoshi

2017-02-01

The nuclear disaster at the Fukushima Daiichi Nuclear Power Plant (FDNPP) in March 2011 caused partial meltdowns of three reactors. During the meltdowns, a type of condensed particle, a caesium-rich micro-particle (CsMP), formed inside the reactors via unknown processes. Here we report the chemical and physical processes of CsMP formation inside the reactors during the meltdowns based on atomic-resolution electron microscopy of CsMPs discovered near the FDNPP. All of the CsMPs (with sizes of 2.0-3.4 μm) comprise SiO2 glass matrices and ~10-nm-sized Zn-Fe-oxide nanoparticles associated with a wide range of Cs concentrations (1.1-19 wt% Cs as Cs2O). Trace amounts of U are also associated with the Zn-Fe oxides. The nano-texture in the CsMPs records multiple reaction-process steps during meltdown in the severe FDNPP accident: Melted fuel (molten core)-concrete interactions (MCCIs), incorporating various airborne fission product nanoparticles, including CsOH and CsCl, proceeded via SiO2 condensation over aggregates of Zn-Fe oxide nanoparticles originating from the failure of the reactor pressure vessels. Still, CsMPs provide a mechanism by which volatile and low-volatility radionuclides such as U can reach the environment and should be considered in the migration model of Cs and radionuclides in the current environment surrounding the FDNPP.

Innovations in systems engineering and analysis for the simulation of beyond design-base accidents

International Nuclear Information System (INIS)

Frisch, W.; Beraha, D.

1990-01-01

An important target in improving reactor safety is to have the most realistic simulation possible of beyond design-base accidents in the computer. This paper presents new developments in ATHLET and further developments (description of the thermo-fluid-dynamic conditions in the core and cooling circuits during serious incidents in the computer programme ATHLET-SA) and extensions (link-up to RALOC). RALOC is a computer programme for describing thermodynamic conditions inside the containment during design-base accidents and accidents involving core meltdown. Further research is dedicated to code acceleration. (DG) [de

Overview of core disruptive accidents

International Nuclear Information System (INIS)

Marchaterre, J.F.

1977-01-01

An overview of the analysis of core-disruptive accidents is given. These analyses are for the purpose of understanding and predicting fast reactor behavior in severe low probability accident conditions, to establish the consequences of such conditions and to provide a basis for evaluating consequence limiting design features. The methods are used to analyze core-disruptive accidents from initiating event to complete core disruption, the effects of the accident on reactor structures and the resulting radiological consequences are described

Accident at Harrisburg

International Nuclear Information System (INIS)

1979-05-01

The course of events during the accident on 28 March 1979 at Three Mile Island-2 Reactor at Harrisburg, Pennsylvania, is described in detail. The effects (in the environment and within the safety containment) are described. The following points are then discussed: the possibility of a comparable accident occurring in the nuclear power stations in the German Federal Republic; the possibility of any point having been overlooked in the design of nuclear power stations in the Federal Republic; whether previous risk analyses are still valid; and how near the Three Mile Island reactor was to a core meltdown. Some conclusions are drawn. (U.K.)

Neutronics simulations on hypothetical power excursion and possible core melt scenarios in CANDU6

International Nuclear Information System (INIS)

Kim, Yonghee

2015-01-01

LOCA (Loss of coolant accident) is an outstanding safety issue in the CANDU reactor system since the coolant void reactivity is strongly positive. To deal with the LOCA, the CANDU systems are equipped with specially designed quickly-acting secondary shutdown system. Nevertheless, the so-called design-extended conditions are requested to be taken into account in the safety analysis for nuclear reactor systems after the Fukushima accident. As a DEC scenario, the worst accident situation in a CANDU reactor system is a unprotected LOCA, which is supposed to lead to a power excursion and possibly a core melt-down. In this work, the hypothetical unprotected LOCA scenario is simulated in view of the power excursion and fuel temperature changes by using a simplified point-kinetics (PK) model accounting for the fuel temperature change. In the PK model, the core reactivity is assumed to be affected by a large break LOCA and the fuel temperature is simulated to account for the Doppler effect. In addition, unlike the conventional PK simulation, we have also considered the Xe-I model to evaluate the impact of Xe during the LOCA. Also, we tried to simulate the fuel and core melt-down scenario in terms of the reactivity through a series of neutronics calculations for hypothetical core conditions. In case of a power excursion and possible fuel melt-down situation, the reactor system behavior is very uncertain. In this work, we tried to understand the impacts of fuel melt and relocation within the pressure vessel on the core reactivity and failure of pressure and calandria tubes. (author)

The nature of reactor accidents

International Nuclear Information System (INIS)

Domaratzki, Z.; Campbell, F.R.; Atchison, R.J.

1981-01-01

Reactor accidents are events which result in the release of radioactive material from a nuclear power plant due to the failure of one or more critical components of that plant. The failures, depending on their number and type, can result in releases whose consequences range from negligible to catastrophic. By way of examples, this paper describes four specific accidents which cover this range of consequence: failure of a reactor control system, loss of coolant, loss of coolant with impaired containment, and reactor core meltdown. For each a possible sequence of events and an estimate of the expected frequency are presented

PWR severe accident mitigation measures, the french point of view

International Nuclear Information System (INIS)

Duco, J.; L'Homme, A.; Queniart, D.

1990-01-01

French studies have early considered the fact that, despite all the precautions taken, the possibility of severe accidents cannot be absolutely excluded; these accidents include core meltdown and a more or less significant loss, at an early or later stage, of the confinement of the radioactive substances in the containment. For a given scenario, one can almost always imagine a more severe scenario by postulating additional failures, but it is obvious that, as the severity of the imagined scenario increases, the probability of its occurrence tends towards zero. However, it does not appear reasonable to attempt to set a probability threshold below which the scenarios should be excluded. First of all, the higher the improbability of the scenarios, the greater the uncertainty in the calculation of their probability, with the result that the calculation is not very meaningful. Secondly, and more importantly, this approach ignores the essential problem of accident situation management. From the outset, French studies have been focused on controlling the development of these situations and mitigating their consequences by means of a series of appropriate actions involving, on the one hand, optimum use of the resources available in the installation during the course of the accident and, on the other hand, the taking of protective measures for the population. To attempt to prevent an initial event to degenerate into a severe accident leading to core meltdown if the proper actions are not taken, Electricite de France has proposed a new operating procedure based on the characterization of every possible cooling state of the core

Recriticality, a Key Phenomenon to Investigate in Core Disruptive Accident Scenarios of Current and Future Fast Reactor Designs

International Nuclear Information System (INIS)

Maschek, W.; Rineiski, A.; Flad, M.; Kriventsev, V.; Gabrielli, F.; Morita, K.

2012-01-01

Final comments and conclusions: • Modern plants, should have performed better under Fukushima type event. • In future fast reactor systems significantly higher active and passive safety features are installed, which should cope with events like Fukushima. • One important lesson: put a focus on rare initiators, accident routes and consequences that are neither expected nor have been observed, events that are categorized under ‘black swans’. • Importance of severe accident research demonstrated - both analytically and experimentally for assessing and interpreting accident scenarios and developments. Precondition for developing preventive & mitigative safety measures. Passive safety measures are in the focus of advanced design options and must work under conditions of multiple loads and aggravating events. • Fast reactor systems behavior as the SFR under severe accident conditions: – In fast spectrum systems as the SFR the core is not in its neutronically most reactive configuration and SFRs may be loaded with MAs for waste management; – Recriticalities have a high probability because of the higher enrichment levels; – Short time scales have to be envisioned for core melt-down; – Decay heat levels might be significantly higher, if MA bearing fuel is involved. • Improve design by measures for prevention and/or mitigation of recriticalities; – High reliability of simulations required for proof; • Assessment of fuel relocated on peripheral structures; • Preventive/mitigating measures should not replace containment measures

Environmental impacts of an accident with a nuclear power plant

International Nuclear Information System (INIS)

1985-10-01

A maximum credible reactor accident is considered: all safety systems fail and the reactor core is not cooled anymore. This so-called meltdown accident is discussed for two different weather situations. For these cases, the effects on public health and environment is studied (radioactive clouds, inhalation and deposition of radioactive materials). The radiation doses calculated are compared with standard levels. In so doing, an estimation is made of the measures necessary to reduce unfavourable consequences. (G.J.P.)

Tchernobyl accident

International Nuclear Information System (INIS)

1986-06-01

First, R.M.B.K type reactors are described. Then, safety problems are dealt with reactor control, behavior during transients, normal loss of power and behavior of the reactor in case of leak. A possible scenario of the accident of Tchernobyl is proposed: events before the explosion, possible initiators, possible scenario and events subsequent to the core meltdown (corium-concrete interaction, interaction with the groundwater table). An estimation of the source term is proposed first from the installation characteristics and the supposed scenario of the accident, and from the measurements in Europe; radiological consequences are also estimated. Radioactivity measurements (Europe, Scandinavia, Western Europe, France) are given in tables (meteorological maps and fallouts in Europe). Finally, a description of the site is given [fr

Teaching of severe accident of Fukushima Daiichi Nuclear Power Plants of Tokyo Electric Power

International Nuclear Information System (INIS)

Saito, Shinzo

2011-01-01

The Great East Japan Earthquake and accompanied tsunami brought about the severe accident at Fukushima Daiichi Nuclear Power Plants of Tokyo Electric Power Co., Inc. For 'No more Fukushima', twelve teaching of the accident was pointed out as follows: 1) natural disasters and external events shall be taken into consideration, 2) severe accident shall be included into safety regulation, 3) all possibility of hydrogen explosion shall be excluded, 4) diversity of safety important component and equipment shall be added with sufficient period of outage, 5) siting of multiple units at the same site shall be avoided at quake-prone country like Japan, 6) accident response environment for operators shall be improved, 7) accident convergence termination system shall be established so as to concentrate technical experience and knowledge, 8) off-site center shall be improved, 9) resident evacuation, consumption limit of food, radiation exposure and soil contamination limit shall be decided openly, 10) nuclear regulation and prevention of disaster shall be conducted by unitary organization to gain public trust, 11) fostering of safety culture among relevant enterprises shall be more encouraged and 12) nuclear industry shall develop reactor such as with no core meltdown or no evacuation and environmental contamination even if reactor core would be meltdown. (T. Tanaka)

Severe accidents in nuclear reactors

International Nuclear Information System (INIS)

Ohai, Dumitru; Dumitrescu, Iulia; Tunaru, Mariana

2004-01-01

The likelihood of accidents leading to core meltdown in nuclear reactors is low. The consequences of such an event are but so severe that developing and implementing of adequate measures for preventing or diminishing the consequences of such events are of paramount importance. The analysis of major accidents requires sophisticated computation codes but necessary are also relevant experiments for checking the accuracy of the predictions and capability of these codes. In this paper an overview of the severe accidents worldwide with definitions, computation codes and relating experiments is presented. The experimental research activity of severe accidents was conducted in INR Pitesti since 2003, when the Institute jointed the SARNET Excellence Network. The INR activity within SARNET consists in studying scenarios of severe accidents by means of ASTEC and RELAP/SCDAP codes and conducting bench-scale experiments

A condensed review of the core catcher in the LMR

International Nuclear Information System (INIS)

Lee, Yong Bum; Hahn, Do hee

2001-03-01

The overwhelming emphasis in reactor safety is on the prevention of core meltdown. Moreover, although there have been several accidents that have resulted in some fuel melting, to date there have been no accidents severe enough to cause the syndrome of core collapse, reactor vessel melt-through, containment penetration, and dispersal into the ground. Nevertheless, a number of proposals have been made for the design of core catcher systems to control or stop the motion of the molten core mass should such an accident take place. Core catchers may differ in both their location within the reactor system and in the mechanism that is used to cool and control the motion of the core debris. In this report the classification, configuration and main features of the core catcher are described. And also, the core catcher provisions in constructed and planned LMRs (Liquid Metal Reactors) are summarized

Radioactive contamination of Danish territory after core-melt accidents at the Barsebaeck power plant

International Nuclear Information System (INIS)

Gjoerup, H.L.; Jensen, N.O.; Hedemann Jensen, P.; Kristensen, L.; Nielsen, O.J.; Petersen, E.L.; Petersen, T.; Roed, J.; Thykier-Nielsen, S.; Heikel Vinter, F.; Warming, L.; Aarkrog, A.

1982-03-01

An assessment is made of the radioactive contamination of Danish territory in the event of a core-melt accident at the Barsebaeck nuclear power plant in Sweden. Accidents including both core melt-down and containment failure are considered. Consequences are calculated for a BWR-3 release under common meteorological conditions and for a BWR-2 release under extreme meteorological conditions. Calculations are based on experiments and theoretical work relating to deposition velocities for different types of surface, shielding effect of structures, and weathering. The effects are described of different dose-reducing measures, e.g., decontamination, relocation, destruction of contaminated foodstuffs. The collective effective dose equivalent from external gamma radiation from deposited activity integrated over a time period of 30 years, is calculated to be 3.6 Megamanrem in the BWR-3 case without dose-reducing measures. For the BWR-2 case, the corresponding dose is approx. 41 Megamanrem. A combination of temporary relocation, hosing of roads etc. and digging of gardens is estimated to reduce these doses to approx. 2.5 Megamanrem and approx. 15 Megamanrem, respectively. The collective committed effective dose equivalent from the consumption of contaminated foodstuffs is calculated to 23 Megamanrem in the BWR-3 case without dose-reducing measures. This dose could be reduced to 0.2 Megamanrem if contaminated crops are destroyed during the first year after the accident and if changes are made in agricultural production in the contaminated area. The corresponding doses in the BWR-2 case would be 197 Megamanrem and 1.4 Megmanrem, respectively. (author)

Reaction- and melting behaviour of LWR-core components UO2, Zircaloy and steel during the meltdown period

International Nuclear Information System (INIS)

Hofmann, P.

1976-07-01

The reaction behaviour of the UO 2 , Zircaloy-4 and austenitic steel core components was investigated as a function of temperature (till melting temperatures) under inert and oxidizing conditions. Component concentrations varied between that of Corium-A (65 wt.% UO 2 , 18% Zry, 17% steel) and that of Corium-E (35 wt.% UO 2 , 10% Zry, 55% steel). In addition, Zircaloy and stainless steel were used with different degrees of oxidation. The paper describes systematically the phases that arise during heating and melting. The integral composition of the melts and the qualitative as well as quantitative analysis of the phases present in solidified corium are given. In some cases melting points have been determined. The reaction and melting behaviour of the corium specimens strongly depends on the concentration and on the degree of oxidation of the core components. First liquid phases are formed at the Zry-steel interface at about 1,350 0 C. The maximum temperatures of about 2,500 0 C for the complete melting of the corium-specimens are well below the UO 2 melting point. Depending on the steel content and/or degree of oxidation of Zry and steel, a homogeneous metallic or oxide melt or two immiscible melts - one oxide and the other metallic - are obtained. During the melting experiments performed under inert gas conditions the chemical composition of the molten specimens generally change by evaporation losses of single elements, especially of uranium, zirconium and oxygen. The total weight losses go up to 30%; under oxidizing conditions they are substantially smaller due to the occurrence of different phases. In air or water vapor, the occurrence of the phases and the melting behaviour of the core components are strongly influenced by the oxidation rate and the oxygen supply to the surface of the melt. In the case of the hypothetical core melting accident, a heterogeneous melt (oxide and metallic) is probable after the meltdown period. (orig./RW) [de

CNE (central nuclear en Embalse): probabilistic safety study. Loss-of-coolant accidents. Analysis through events sequence

International Nuclear Information System (INIS)

Layral, S.I.

1987-01-01

The aim of this study was to perform for the Embalse nuclear power plant, a probabilistic evaluation of loss-of-coolant accidents (LOCA) to identify the risks associated with them and to determine their acceptability in accordance with norms. This study includes all ruptures in the primary system that produce the automatic activation of 'emergency core cooling system'. Three starting events were selected for the probabilistic evaluation: 100% rupture of an input collector; 5% rupture of an input collector; 1.2% rupture of an input collector. At this stage the evaluation is focussed on the identification and quantization of the main failure sequences that follow a LOCA and lead to an uncontrolled reactor state or 'core meltdown'. The most important contribution to the core meltdown due to LOCA is the failure of supplies that are required for the emergency core cooling system. (Author)

ATHENA-2D: A computer code for simulation of hypothetical recriticality accidents in a thermal neutron spectrum

International Nuclear Information System (INIS)

Schwinkendorf, K.N.

1995-01-01

In a damaged light water reactor core (as in the aftermath of a Three-Mile-Island-like core meltdown), water reflood is performed to carry off decay heat. The severely degraded geometry of the fuel debris bed may increase core reactivity with water reflood. Sufficient boron poisoning of the reflood water is therefore very important. One hypothetical accident is the reintroduction of cooling water that is insufficiently borated, resulting in the damaged reactor attaining criticality in this uncontrolled configuration. The goal in simulating this accident is the prediction of the energy release from the resulting transient

A review of the core catcher design in LMR

International Nuclear Information System (INIS)

Lee, Yong Bum; Hahn, Do Hee

2001-08-01

The overwhelming emphasis in reactor safety is on the prevention of core meltdown. Moreover, although there have been several accidents that have resulted in some fuel melting, to date there have been no accidents severe enough to cause the syndrome of core collapse, reactor vessel melt-through, containment penetration, and dispersal into the ground. Nevertheless, a number of proposals have been made for the design of core catcher systems to control or stop the motion of the molten core mass should such an accident take place. Core catchers may differ in both their location within the reactor system and in the mechanism that is used to cool and control the motion of the core debris. In this report the classification, configuration and main features of the core catcher are described. And also, The core catcher design technologies and processes are presented. Finally the core catcher provisions in constructed and planned LMRs (Liquid Metal Reactors) are summarized and the preliminary assessment on the core catcher installation in KALIMER is presented

Phenomena in the interaction among a core melt and protective and sacrificial materials

International Nuclear Information System (INIS)

Steinwarz, W.; Koller, W.; Dyllong, N.; Fischer, M.; Hellmann, S.; Lansmann, V.; Nie, M.; Haefner, W.; Alkan, Z.; Andrae, P.; Rensing, B.

2000-01-01

In a postulated core meltdown accident in a light water reactor there are bound to be interactions, in the ex-vessel phase, among the core melt and the structural materials within and below the reactor cavity. In existing plants, these structural materials normally are structural concrete, while future, evolutionary reactor lines are to have sacrificial and protective materials specially designed for this hypothetical case. To add to the state of knowledge about the phenomena occurring, experiments need to be conducted under conditions as realistic as possible. Within the research programs funded by the European Union, the German Federal Ministry for Economics, and the German nuclear power plant operators, experiments on a laboratory as well as an industrial scale on these problems are being carried out in the two projects called CORESA (COrium on REfractory and SAcrificial materials) and ECOSTAR (Ex-vessel COre melt STAbilization Research). The experiments are accompanied by an extensive analytical theoretical program also serving to advance and validate computer codes on the problems under investigation. The projects, which are carried out with international European participation, are expected to allow a concept to be developed for managing postulated accident scenarios involving core meltdown for innovative nuclear power plants, and to provide findings on risk evaluation of plants now in operation so as to further develop accident management measures. (orig.) [de

Investigation of the different scenarios occurring in a PWR in case of a TMLB accident

International Nuclear Information System (INIS)

Pochard, R.; Dufresne, J.; Autrusson, B.

1988-10-01

Severe accidents in light water reactors fall into one of two main categories, depending on whether or not core meltdown is accompanied by a pressure buildup in the primary system. The way in which the accident develops is, in fact, largely conditioned by this pressure aspect: temperature distribution in the core and primary system resulting from natural convection gas streams; fuel clad failure mode, etc... One major effect of pressure buildup on the accident scenario is primary system failure under the combined actions of pressure and temperature. The purpose of the present paper is to present, after a detailed thermalhydraulic study, an analysis of the timing and location of the system failures in case of a TMLB accident on CPY french type reactor

Reactivity accident analysis in MTR cores

International Nuclear Information System (INIS)

Waldman, R.M.; Vertullo, A.C.

1987-01-01

The purpose of the present work is the analysis of reactivity transients in MTR cores with LEU and HEU fuels. The analysis includes the following aspects: the phenomenology of the principal events of the accident that takes place, when a reactivity of more than 1$ is inserted in a critical core in less than 1 second. The description of the accident that happened in the RA-2 critical facility in September 1983. The evaluation of the accident from different points of view: a) Theoretical and qualitative analysis; b) Paret Code calculations; c) Comparison with Spert I and Cabri experiments and with post-accident inspections. Differences between LEU and HEU RA-2 cores. (Author)

Apparatus for controlling nuclear core debris

Science.gov (United States)

Jones, Robert D.

1978-01-01

Nuclear reactor apparatus for containing, cooling, and dispersing reactor debris assumed to flow from the core area in the unlikely event of an accident causing core meltdown. The apparatus includes a plurality of horizontally disposed vertically spaced plates, having depressions to contain debris in controlled amounts, and a plurality of holes therein which provide natural circulation cooling and a path for debris to continue flowing downward to the plate beneath. The uppermost plates may also include generally vertical sections which form annular-like flow areas which assist the natural circulation cooling.

Apparatus for controlling nuclear core debris

International Nuclear Information System (INIS)

Jones, R.D.

1978-01-01

Disclosed is an apparatus for containing, cooling, and dispersing reactor debris assumed to flow from the core area in the unlikely event of an accident causing core meltdown. The apparatus includes a plurality of horizontally disposed vertically spaced plates, having depressions to contain debris in controlled amounts, and a plurality of holes therein which provide natural circulation cooling and a path for debris to continue flowing downward to the plate beneath. The uppermost plates may also include generally vertical sections which form annular-like flow areas which assist the natural circulation cooling

Review of the TMI-2 accident evaluation and vessel investigation projects

Energy Technology Data Exchange (ETDEWEB)

Ladekarl Thomsen, Knud

1998-03-01

The results of the TMI-2 Accident Evaluation Programme and the Vessel Investigation Project have been reviewed as part of a literature study on core meltdown and in-vessel coolability. The emphasis is placed on the late phase melt progression, which is of special relevance to the NKS-sponsored RAK-2.1 project on Severe Accident Phenomenology. The body of the report comprises three main sections, The TMI-2 Accident Scenario, Core Region and Relocation Path Investigations, and Lower Head Investigations. In the final discussion, the lower head gap formation mechanism is explained in terms of thermal contraction and fracturing of the debris crust. This model seems more plausible than the MAAP model based on creep expansion of the lower head. (au) 1 tab., 33 ills., 31 refs.

Serious accidents of PWR type reactors for power generation

International Nuclear Information System (INIS)

2008-12-01

This document presents the great lines of current knowledge on serious accidents relative to PWR type reactors. First, is exposed the physics of PWR type reactor core meltdown and the possible failure modes of the containment building in such a case. Then, are presented the dispositions implemented with regards to such accidents in France, particularly the pragmatic approach that prevails for the already built reactors. Then, the document tackles the case of the European pressurized reactor (E.P.R.), for which the dimensioning takes into account explicitly serious accidents: it is a question of objectives conception and their respect must be the object of a strict demonstration, by taking into account uncertainties. (N.C.)

Transient debris freezing and potential wall melting during a severe reactivity initiated accident experiment

International Nuclear Information System (INIS)

El-Genk, M.S.; Moore, R.L.

1981-01-01

It is important to light water reactor (LWR) safety analysis to understand the transient freezing of molten core debris on cold structures following a hypothetical core meltdown accident. The purpose of this paper is to (a) present the results of a severe reactivity initiated accident (RIA) in-pile experiment with regard to molten debris distribution and freezing following test fuel rod failure, (b) analyze the transient freezing of molten debris (primarily a mixture of UO/sub 2/ fuel and Zircaloy cladding) deposited on the inner surface of the test shroud wall upon rod failure, and (c) assess the potential for wall melting upon being contacted by the molten debris. 26 refs

Severe accident analysis using MARCH 1.0 code

International Nuclear Information System (INIS)

Guimaraes, A.C.F.

1987-09-01

The description and utilization of the MARCH 1.0 computer code, which aim to analyse physical phenomena associated with core meltdown accidents in PWR type reactors, are presented. The primary system is modeled as a single volume which is partitioned into a gas (steam and hydrogen) region and a water region. March predicts blowdown from the primary system in single phase. Based on results of the probabilistic safety analysis for the Zion and Indian Point Nuclear Power Plants, the S 2 HFX sequence accident for Angra-1 reactor is studied. The S 2 HFX sequence means that the loss of coolant accident occurs through small break in primary system with bot total failures of the reactor safety system and containment in yours recirculation modes, leading the core melt and the containment failure due to overpressurization. The obtained results were considered reasonable if compared with the results obtained for the Zion and Indian Point nuclear power plants. (Author) [pt

Technical bases for estimating fission product behavior during LWR accidents. Technical report

International Nuclear Information System (INIS)

1981-06-01

The objective of this report is to provide the Nuclear Regulatory Commission and the public with a description of the best technical information currently available for estimating the release of radioactive material during postulated reactor accidents, and to identify where gaps exist in our knowledge. This report focuses on those low probability-high consequence accidents involving severe damage to the reactor core and core meltdown that dominate the risk to the public. Furthermore, in this report particular emphasis is placed on the accident behavior of radioactive iodine, as (1) radioiodine is predicted to be a major contributor to public exposure, (2) current regulatory accident analysis procedures focus on iodine, and (3) several technical issues have been raised recently about the magnitude of iodine release. The generation, transport, and attenuation of aerosols were also investigated in some detail to assess their effect on fission product release estimates and to determine the performance of engineered safety features under accident conditions exceeding their design bases

Accident source terms for Light-Water Nuclear Power Plants. Final report

International Nuclear Information System (INIS)

Soffer, L.; Burson, S.B.; Ferrell, C.M.; Lee, R.Y.; Ridgely, J.N.

1995-02-01

In 1962 tile US Atomic Energy Commission published TID-14844, ''Calculation of Distance Factors for Power and Test Reactors'' which specified a release of fission products from the core to the reactor containment for a postulated accident involving ''substantial meltdown of the core''. This ''source term'', tile basis for tile NRC's Regulatory Guides 1.3 and 1.4, has been used to determine compliance with tile NRC's reactor site criteria, 10 CFR Part 100, and to evaluate other important plant performance requirements. During the past 30 years substantial additional information on fission product releases has been developed based on significant severe accident research. This document utilizes this research by providing more realistic estimates of the ''source term'' release into containment, in terms of timing, nuclide types, quantities and chemical form, given a severe core-melt accident. This revised ''source term'' is to be applied to the design of future light water reactors (LWRs). Current LWR licensees may voluntarily propose applications based upon it

Analysis and research status of severe core damage accidents

International Nuclear Information System (INIS)

1984-03-01

The Severe Core Damage Research and Analysis Task Force was established in Nuclear Safety Research Center, Tokai Research Establishment, JAERI, in May, 1982 to make a quantitative analysis on the issues related with the severe core damage accident and also to survey the present status of the research and provide the required research subjects on the severe core damage accident. This report summarizes the results of the works performed by the Task Force during last one and half years. The main subjects investigated are as follows; (1) Discussion on the purposes and necessities of severe core damage accident research, (2) proposal of phenomenological research subjects required in Japan, (3) analysis of severe core damage accidents and identification of risk dominant accident sequences, (4) investigation of significant physical phenomena in severe core damage accidents, and (5) survey of the research status. (author)

Method for consequence calculations for severe accidents

International Nuclear Information System (INIS)

Nielsen, F.

1988-07-01

This report was commissioned by the Swedish State Power Board. The report contains a calculation of radiation doses in the surroundings caused by a theoretical core meltdown accident at Forsmark reactor No 3. The accident sequence chosen for the calculating was a release caused by total power failure. The calculations were made by means of the PLUCON4 code. Meteorological data for two years from the Forsmark meteorological tower were analysed to find representative weather situations. As typical weather, Pasquill D was chosen with a wind speed of 5 m/s, and as extreme weather, Pasquill F with a wind speed of 2 m/s. 23 tabs., 37 ills., 20 refs. (author)

Core catcher concepts future PWR-Plants

International Nuclear Information System (INIS)

Alsmeyer, H.; Werle, H.

1994-01-01

Light water reactors of the next generation should have still greater passive safety, even in the most serious accidents. This includes the long term safe inclusion of the core inventory in the case of core meltdown accidents. The three concepts for cooling the liquefied core outside the reactor pressure vessel examined by KfK should remove the post-shutdown heat by direct contact of the melt with water. The geometric distribution of the melt increases its surface area, so that favourable conditions for heat removal from the poorly thermally-conducting melt are created and complete quick solidification occurs. The experiments examine both the relocation and distribution mechanisms of the melt and the reactions occurring when water enters. As strong interaction is possible on direct contact of the melt with water, an important aim is experimental determination and limitation of any resulting mechanical stresses. (orig./HP) [de

Serious reactor accidents reconsidered

International Nuclear Information System (INIS)

1987-12-01

The chance is determined for damage of the reactor core and that sequel events will cause excursion of radioactive materials into the environment. The gravity of such an accident is expressed by the source term. It appears that the chance for such an accident varies with the source term. In general it is valid that how larger the source term how smaller the chance is for it and vice versa. The chance for excursion is related to two complexes of events: serious damage (meltdown) of the reactor core, and the escape of the liberated radionuclides into the environment. The results are an order of magnitude consideration of the relation between the extent of the source term and the chance for it. From the spectrum of possible source terms three representative ones have been chosen: a large, a medium and a relative small source term. This choice is in accordance with international considerations. The hearth of this study is the estimation of the chance for occurrence of the three chosen source terms for new light-water reactors. refs.; figs.; tabs

Method for consequence calculations for severe accidents

International Nuclear Information System (INIS)

Nielsen, F.; Thykier-Nielsen, S.; Walmod-Larsen, O.

1986-08-01

This report was commissioned by the Swedish State Power Board, who wanted a method for calculation of radiation doses in the surroundings of nuclear power plants caused by severe accidents. The PLUCON4 code were used for the calculations. A TC-SV-accident at Ringhals 1 wer chosen as example. A transient without shutdown leads to core meltdown through the reactor vessel. The pressure peak at the moment of vessel failure opens a safety valve in the dry well. Meteorolgical data for two years from the Ringhals meteorological tower were analysed to find representative weather situations. As typical weather were chosen Pasquill D with wind speed 8 m/s, and as extreme weather were chosen Pasquill F with wind speed 4.8 m/s. (author)

Method for consequence calculations for severe accidents

International Nuclear Information System (INIS)

Nielsen, F.

1988-01-01

This report was commissioned by the Swedish State Power Board. The report contains a calculation of radiation doses in the surroundings caused by a theoretical core meltdown accident at Ringhals reactor No 3/4. The accident sequence chosen for the calcualtions was a release caused by total power failure. The calculations were made by means of the PLUCON4 code. A decontamination factor of 500 is used to account for the scrubber effect. Meteorological data for two years from the Ringhals meteorological tower were analysed to find representative weather situations. As typical weather, Pasquill D, was chosen with a wind speed of 10 m/s, and as extreme weather, Pasquill E, with a wind speed of 2 m/s. 19 refs. (author)

Accident-tolerant control rod

International Nuclear Information System (INIS)

Ohta, Hirokazu; Sawabe, Takashi; Ogata, Takanari

2013-01-01

Boron carbide (B 4 C) and hafnium (Hf) metal are used for the neutron absorber materials of control rods in BWRs, and silver-indium-cadmium (Ag-In-Cd) alloy is used in PWRs. These materials are clad with stainless steel. The eutectic point of B 4 C and iron (Fe) is about 1150 deg. C and the melting point of Ag-In-Cd alloy is about 800 deg. C, which are lower than the temperature of zircaloy - steam reaction increases rapidly (∼1200 deg. C). Accordingly, it is possible that the control rods melt and collapse before the reactor core is significantly damaged in the case of severe accidents. Since the neutron absorber would be separated from the fuels, there is a risk of re-criticality, when pure water or seawater is injected for emergency cooling. In order to ensure sub-criticality and extend options of emergency cooling in the course of severe accidents, a concept of accident-tolerant control rod (ACT) has been derived. ACT utilises a new absorber material having the following properties: - higher neutron absorption than current control rod; - higher melting or eutectic temperature than 1200 deg. C where rapid zircaloy oxidation occurs; - high miscibility with molten fuel materials. The candidate of a new absorber material for ATC includes gadolinia (Gd 2 O 3 ), samaria (Sm 2 O 3 ), europia (Eu 2 O 3 ), dysprosia (Dy 2 O 3 ), hafnia (HfO 2 ). The melting point of these materials and the liquefaction temperature with Fe are higher than the rapid zircaloy oxidation temperature. ACT will not collapse before the core melt-down. After the core melt-down, the absorber material will be mixed with molten fuel material. The current absorber materials, such as B 4 C, Hf and Ag-In-Cd, are charged at the tip of ATC in which the neutron flux is high, and a new absorber material is charged in the low-flux region. This design could minimise the degradation of a new absorber material by the neutron absorption and the influence of ATC deployment on reactor control procedure. As a

Post-accident heat removal research: A state of the art review

International Nuclear Information System (INIS)

Mueller, U.; Schulenberg, T.

1983-11-01

For a realistic assessment of the consequence of extremely unlikely reactor accidents resulting in core degradation or core meltdown key questions are how to remove the decay heat from the reactor system and how to retain the radioactive core debris within the containment. Usually, this complex of questions is referred to as Post-Accident Heat Removal (PAHR). In this article the research work on PAHR performed by various institutions during the last decade has been reviewed. The main results have been summarized under the chapter headings ''Accident Scenarios,'' - ''Core Debris Accommodation Concepts,'' and ''PAHR Topics.'' Particular emphasis has been placed on the presentation of the following problems: characteristics and coolability of solid core debris in the vector vessel, heat removal from molten pools of core material, and core-melt interaction with structural materials. Some unresolved or insufficiently answered questions relating to special ''PAHR Topics'' have been mentioned or discussed at the end of the particular Chapter. Problem areas of major uncertainty have been identified and listed at the end of the review article. They include the following subjects: formation of debris beds and bed characteristics, post dryout behaviour of particle beds, long-term availability and proper location of heat sinks, creep rupture of structures under high thermal loads. (orig.) [de

Passive decay heat removal by natural air convection after severe accidents

Energy Technology Data Exchange (ETDEWEB)

Erbacher, F.J.; Neitzel, H.J. [Forschungszentrum Karlsruhe Institut fur Angewandte Thermo- und Fluiddynamik, Karlsruhe (Germany); Cheng, X. [Technische Universitaet Karlsruhe Institut fur Stroemungslehre und Stroemungsmaschinen, Karlsruhe (Germany)

1995-09-01

The composite containment proposed by the Research Center Karlsruhe and the Technical University Karlsruhe is to cope with severe accidents. It pursues the goal to restrict the consequences of core meltdown accidents to the reactor plant. One essential of this new containment concept is its potential to remove the decay heat by natural air convection and thermal radiation in a passive way. To investigate the coolability of such a passive cooling system and the physical phenomena involved, experimental investigations are carried out at the PASCO test facility. Additionally, numerical calculations are performed by using different codes. A satisfying agreement between experimental data and numerical results is obtained.

Release of gases and their influence on containment integrity during a hypothetical meltdown accident

International Nuclear Information System (INIS)

Hassmann, K.; Reimann, M.

1981-01-01

The sequence of a hypothetical core melt down accident has been subdivided into four phases. Heating up of the core until failure of the core support structure is the first phase. It starts at a certain water level in the reactor pressure vessel (RPV) and ends with the failure of the grid plate. The second phase is characterized by the evaporation of the water in the lower plenum of the RPV. The second phase lasts until a molten core debris is formed. The third phase is concerned with the heating up of the pressure vessel after formation of a molten pool in the lower plenum of the RPV. After pressure vessel failure, the molten corium will interact in the fourth phase with the concrete structure beneath the pressure vessel. In this paper the gas release during all four accident phases and the resulting pressure-time history within the containment of a German standard PWR is given, taking into account violent combustion of hydrogen. In particular, the differences caused by dsestruction of concrete with silicious and with calcareous aggregates has been analyzed. The basis for the results in the 4th phase is the WECHSL code. Long term containment calculations have been performed with the COCMEL-code

Behavior of LWR fuel elements under accident conditions

International Nuclear Information System (INIS)

Albrecht, H.; Bocek, M.; Erbacher, F.; Fiege, A.; Fischer, M.; Hagen, S.; Hofmann, P.; Holleck, H.; Karb, E.; Leistikow, S.; Melang, S.; Ondracek, G.; Thuemmler, F.; Wiehr, K.

1977-01-01

to evaluate the influence of irradiation and high burnup on fuel failure mechanisms during accident conditions. Under the extreme hypothetical assumption that in the case of a LOCA simultaneously all emergency core cooling systems fail, the consequences of a core meltdown accident and the possibilities to mitigate the consequences are investigated. Results are described on the meltdown behavior of LWR fuel rods, on the reaction behavior of mixtures of molten core components, and the most important core melt properties, on the interaction process of core melts with the concrete structure of a reactor and the associated fission product release

Research work for improving LWR safety

International Nuclear Information System (INIS)

Bork, G.

1993-09-01

The work performed in 1992 for the PSF project centers on various phenomena of severe fuel damage and on selected aspects of a core meltdown accident, relating to aerosol behaviour and filter engineering, and to methods of assessing and minimizing the radiological impacts of a reactor accident. The 1992 task programme of the project included research into extreme load conditions affecting the containment in a core meltdown accident: first results are given of the experiments performed. (orig./HP) [de

Studies on melt-water-structure interaction during severe accidents

International Nuclear Information System (INIS)

Sehgal, B.R.; Dinh, T.N.; Okkonen, T.J.; Bui, V.A.; Nourgaliev, R.R.; Andersson, J.

1996-10-01

Results of a series of studies, on melt-water-structure interactions which occur during the progression of a core melt-down accident, are described. The emphasis is on the in-vessel interactions and the studies are both experimental and analytical. Since, the studies performed resulted in papers published in proceedings of the technical meetings, and in journals, copies of a set of selected papers are attached to provide details. A summary of the results obtained is provided for the reader who does not, or cannot, venture into the perusal of the attached papers. (au)

Studies on melt-water-structure interaction during severe accidents

Energy Technology Data Exchange (ETDEWEB)

Sehgal, B.R.; Dinh, T.N.; Okkonen, T.J.; Bui, V.A.; Nourgaliev, R.R.; Andersson, J. [Royal Inst. of Technology, Div. of Nucl. Power Safety, Stockholm (Sweden)

1996-10-01

Results of a series of studies, on melt-water-structure interactions which occur during the progression of a core melt-down accident, are described. The emphasis is on the in-vessel interactions and the studies are both experimental and analytical. Since, the studies performed resulted in papers published in proceedings of the technical meetings, and in journals, copies of a set of selected papers are attached to provide details. A summary of the results obtained is provided for the reader who does not, or cannot, venture into the perusal of the attached papers. (au).

Ecological and toxicological aspects of the partial meltdown of the Chernobyl nuclear power plant reactor

Science.gov (United States)

Eisler, Ronald; Hoffman, David J.; Rattner, Barnett A.; Burton, G. Allen; Cairns, John

1995-01-01

the partial meltdown of the 1000-MW reactor at Chernobyl, Ukraine, on April 26, 1986, released large amounts of radiocesium and other radionuclides into the environment, causing widespread radioactive contamination of Europe and the former Soviet Union.1-7 At least 3,000,000 trillion becquerels (TBq) were released from the fuel during the accident (Table 24.1), dwarfing, by orders of magnitude, radiation released from other highly publicized reactor accidents at Windscale (U.K.) and three-Mile Island (U.S.)3,8 The Chernobyl accident happened while a test was being conducted during a normal scheduled shutdown and is attributed mainly to human error.3

Surface analytical investigations of the release behaviour of volatile fission products during simulated core meltdown accidents and of the reaction behaviour of iodine with silver surfaces

International Nuclear Information System (INIS)

Moers, H.

1986-07-01

The report presents the results of the analysis of aerosol particles formed in simulated laboratory scale core meltdown experiments. In addition the interaction of silver surfaces with gaseous molecular iodine and with iodide and molecular iodine in aqueous solution was investigated. The composition of the aerosol samples and the progress of the reactions mentioned were determined by use of surface analytical techniques (X-ray photoelectron spectroscopy, Auger electron spectroscopy, secondary ion mass spectroscopy). The major information can be evaluated from X-ray photoelectron spectra which exhibit chemical shifts of the photoelectron lines which allowing a discrimination between different chemical species of the same element. The analyses showed that iodine is present in the aerosol particles mainly as caesium iodide and, to a smaller fraction, as silver iodide. During the adsorption of gaseous molecular iodine at metallic silver surfaces a closed silver iodide overlayer is formed. In aqueous iodide solutions one observes chemisorption of the iodide anions up to a coverage of the metallic silver surface of about half a monolayer. Molecular iodine in aqueous solution is completely converted to silver iodide which covers the substrate irregularly. (orig./HP) [de

Three Mile Island Accident Data

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Three Mile Island Accident Data consists of mostly upper air and wind observations immediately following the nuclear meltdown occurring on March 28, 1979, near...

A assessment of loss-of-heat-sink accident with scram in the LMFBR

International Nuclear Information System (INIS)

Bari, R.A.; Ludewig, H.; Pratt, W.T.; Sun, Y.H.

1978-01-01

A description of a slow core meltdown in a liquid metal fast breeder reactor is presented for conditions of loss-of-heat-sink following neutronic shutdown. Simple models are developed for the prediction of phase changes and/or relocation of the core materials including fuel, clad, ducts, control rod absorber material (B 4 C), and plenum gases. The sequence of events is accounted for and the accident progression is described up to the point of recriticality. The neutronic behavior of the disrupted core is analyzed in R-Z geometry with a static transport theory code. For most scenarios assessed, the reactor is expected to become recritical although large ramp rates are not anticipated. (author)

Assessment of the loss-of-heat-sink accident with scram in the LMFBR

International Nuclear Information System (INIS)

Bari, R.A.; Ludewig, H.; Pratt, W.T.; Sun, Y.H.

1978-01-01

A description of a slow core meltdown in a liquid metal fast breeder reactor is presented for the conditions of loss-of-heat-sink following neutronic shutdown. Simple models are developed for the prediction of phase changes and/or relocation of the core materials including fuel, clad, ducts, control rod absorber material (B 4 C), and plenum gases. The sequence of events is accounted for and the accident progression is described up to the point of recriticality. The neutronic behavior of the disrupted core is analyzed in R-Z geometry with a static transport theory code. For most scenarios assessed, the reactor is expected to become recritical although large ramp rates are not anticipated

Core fusion accidents in nuclear power reactors. Knowledge review

International Nuclear Information System (INIS)

Bentaib, Ahmed; Bonneville, Herve; Clement, Bernard; Cranga, Michel; Fichot, Florian; Koundy, Vincent; Meignen, Renaud; Corenwinder, Francois; Leteinturier, Denis; Monroig, Frederique; Nahas, Georges; Pichereau, Frederique; Van-Dorsselaere, Jean-Pierre; Cenerino, Gerard; Jacquemain, Didier; Raimond, Emmanuel; Ducros, Gerard; Journeau, Christophe; Magallon, Daniel; Seiler, Jean-Marie; Tourniaire, Bruno

2013-01-01

This reference document proposes a large and detailed review of severe core fusion accidents occurring in nuclear power reactors. It aims at presenting the scientific aspects of these accidents, a review of knowledge and research perspectives on this issue. After having recalled design and operation principles and safety principles for reactors operating in France, and the main studied and envisaged accident scenarios for the management of severe accidents in French PWRs, the authors describe the physical phenomena occurring during a core fusion accident, in the reactor vessel and in the containment building, their sequence and means to mitigate their effects: development of the accident within the reactor vessel, phenomena able to result in an early failure of the containment building, phenomena able to result in a delayed failure with the corium-concrete interaction, corium retention and cooling in and out of the vessel, release of fission products. They address the behaviour of containment buildings during such an accident (sizing situations, mechanical behaviour, bypasses). They review and discuss lessons learned from accidents (Three Mile Island and Chernobyl) and simulation tests (Phebus-PF). A last chapter gives an overview of software and approaches for the numerical simulation of a core fusion accident

Post-accident core coolability of light water reactors

International Nuclear Information System (INIS)

Michio, I.; Teruo, I.; Tomio, Y.; Tsutao, H.

1983-01-01

A study on post-accident core coolability of LWR is discussed based on the practical fuel failure behavior experienced in NSRR, PBF, PNS and others. The fuel failure behavior at LOCA, RIA and PCM conditions are reviewed, and seven types of fuel failure modes are extracted as the basic failure mechanism at accident conditions. These are: cladding melt or brittle failure, molten UO 2 failure, high temperature cladding burst, low temperature cladding burst, failure due to swelling of molten UO 2 , failure due to cracks of embrittled cladding for irradiated fuel rods, and TMI-2 core failure. The post-accident core coolability at each failure mode is discussed. The fuel failures caused actual flow blockage problems. A characteristic which is common among these types is that the fuel rods are in the conditions violating the present safety criteria for accidents, and UO 2 pellets are in melting or near melting hot conditions when the fuel rods failed

Energetics of LMFBR core disruptive accidents

International Nuclear Information System (INIS)

Marchaterre, J.F.

1979-01-01

In general, in the design of fast reactor systems, containment design margins are specified by investigating the response of the containment to core disruptive accidents. The results of these analyses are then translated into criteria which the designers must meet. Currently, uniform and agreed upon criteria are lacking, and in this time while they are being developed, the designer should be aware of the considerations which go into the particular criteria he must work with, and participate in their development. This paper gives an overview of the current state of the art in assessing core disruptive accidents and the design implications of this process. (orig.)

Study of diluting and absorber materials to control reactivity during a postulated core melt down accident in Generation IV reactors

International Nuclear Information System (INIS)

Plevacova, K.

2010-01-01

In order to limit the consequences of a hypothetical core meltdown accident in Generation IV Sodium Fast Reactors, absorber materials in or near the core, such as boron carbide B 4 C, and diluting materials in the core catcher will be used to prevent recriticality within the mixture of molten oxide fuel and molten structures called corium. The aim of the PhD thesis was to select materials of both types and to understand their behaviour during their interaction with corium, from chemical and thermodynamic point of view. Concerning B 4 C, thermodynamic calculations and experiments agree with the formation of two immiscible phases at high temperature in the B 4 C - UO 2 system: one oxide and one boride. This separation of phases can reduce the efficiency of the neutrons absorption inside the molten fuel contained in the oxide phase. Moreover, a volatilization of a part of the boron element can occur. According to these results, the necessary quantity of B 4 C to be introduced should be reconsidered for postulated severe accident sequence. Other solution could be the use of Eu 2 O 3 or HfO 2 as absorber material. These oxides form a solid solution with the oxide fuel. Concerning the diluting materials, mixed oxides Al 2 O 3 - HfO 2 and Al 2 O 3 - Eu 2 O 3 were preselected. These systems being completely unknown to date at high temperature in association with UO 2 , first points on the corresponding ternary phase diagrams were researched. Contrary to Al 2 O 3 - Eu 2 O 3 - UO 2 system, the Al 2 O 3 - HfO 2 - UO 2 mixture presents only one eutectic and thus only one solidification path which makes easier forecasting the behaviour of corium in the core catcher. (author) [fr

Analysis of the danger potential of H2/CO-combustion in the event of core meltdown

International Nuclear Information System (INIS)

Fischer, M.; Wagler, K.; Schwarzott, W.; Reineke, H.H.

1987-01-01

Based on an evaluation of the present state of knowledge and the experiments performed, several computing programs for the simulation of H 2 /CO combustion processes were developed within the scope of this project. Besides the one-compartment-model MOPED, based on the formulation of empirical and phenomenological connections, which was also used later to perform the pressure buildup analyses during various core meltdown (CM) scenarios, these were the first two attempts in respect of a fluid-dynamic description of the combustion processes that also takes the reaction kinetics into account (VERLA code, PISCES code). The analysis of the low (LP) and high (HP) pressure path CM conditions showed that no additional risk arises on the HP path due to potential H 2 combustion. In opposition to this maximum combustion gas fractions of 15% by vol. H 2 and 2.5% by vol. CO with assumption of complete enrichment in the containment result on the LP path. With 37 refs., 3 tabs., 78 figs [de

Analysis of the primary source term for meltdown accidents using MELCOR 1.8.2

International Nuclear Information System (INIS)

Schmuck, P.

1995-01-01

The MELCOR code describing accident phenomena in the core and primary systems was used for source term calculations and - in the context of the MELCOR Cooperative Assessment Programme - for studying two-phase flows through components such as valves and chokes. Results of the latter studies in comparison to experiments gave hints for an improved calculation of momentum transfer between the phases. (orig.)

Assessment of CRBR core disruptive accident energetics

International Nuclear Information System (INIS)

Theofanous, T.G.; Bell, C.R.

1984-03-01

The results of an independent assessment of core disruptive accident energetics for the Clinch River Breeder Reactor are presented in this document. This assessment was performed for the Nuclear Regulatory Commission under the direction of the CRBR Program Office within the Office of Nuclear Reactor Regulation. It considered in detail the accident behavior for three accident initiators that are representative of three different classes of events; unprotected loss of flow, unprotected reactivity insertion, and protected loss of heat sink. The primary system's energetics accommodation capability was realistically, yet conservatively, determined in terms of core events. This accommodation capability was found to be equivalent to an isentropic work potential for expansion to one atmosphere of 2550 MJ or a ramp rate of about 200 $/s applied to a classical two-phase disassembly

Prediction of thermoplastic failure of a reactor pressure vessel under a postulated core melt accident

International Nuclear Information System (INIS)

Duijvestijn, G.; Birchley, J.; Reichlin, K.

1997-01-01

This paper presents the lower head failure calculations performed for a postulated accident scenario in a commercial nuclear power plant. A postulated one inch break in the primary coolant circuit leads to dryout and subsequent meltdown of the core. The reference plant is a pressurized water reactor without penetrations in the reactor vessel lower head. The molten core material accumulates in the lower head, eventually causing failure of the vessel. The analysis investigates flow conditions in the melt pool, temperature evolution in the reactor vessel wall, and structure mechanical evaluation of the vessel under strong thermal loads and a range of internal pressures. The calculations were performed using the ADINA finite element codes. The analysis focusses on the failure processes, time and mode of failure. The most likely mode of failure at low pressure is global rupture due to gradual accumulation of creep strain over a large part of the heated area. In contrast, thermoplasticity becomes important at high pressure or following a pressure spike and can lead to earlier local failure. In situations in which part of the heat load is concentrated over a small area, resulting in a hot spot, local failure occurs, but not until the temperatures are close to the melting point. At low pressure, in particular, the hot spot area remains intact until the structure is molten across more than half of the thickness. (author) 14 figs., 16 refs

Core catcher for nuclear reactor core meltdown containment

International Nuclear Information System (INIS)

Driscoll, M.J.; Bowman, F.L.

1978-01-01

A bed of graphite particles is placed beneath a nuclear reactor core outside the pressure vessel but within the containment building to catch the core debris in the event of failure of the emergency core cooling system. Spray cooling of the debris and graphite particles together with draining and flooding of coolant fluid of the graphite bed is provided to prevent debris slump-through to the bottom of the bed

Integrated CFD investigation of heat transfer enhancement using multi-tray core catcher in SFR

International Nuclear Information System (INIS)

Rakhi; Sharma, Anil Kumar; Velusamy, K.

2017-01-01

Highlights: • Heat transfer enhancement using multi-tray core catcher for SFR is investigated. • The capability of a single core collector tray is estimated. • Double and triple collector trays with innovative designs is discussed. • Provision of openings in the trays contributed to enhanced natural circulation. - Abstract: To render future SFR more robust and safe, certain BDBE have been considered in the recent years. A Core Disruptive Accident leading to a whole core meltdown scenario has gained the interest of researchers. Various design concepts and safety measures have been suggested and incorporated in design to address such a low probability scenario. A core catcher concept, in particular, has proved to be inevitable as an in-vessel core retention device in SFR for safe retention of core debris arising out after the severe accident. This study aims to analyse the cooling capability of the innovative design concept of core catcher to remove decay heat of degraded core after the accident. First, the capability of single collection tray is established and then the study is extended to two and three collection trays with different design concepts. Transient forms of governing equations of mass, momentum and energy conservations along with k-ε turbulence model are solved by finite volume based CFD solver. Boussinesq approximation is invoked to model buoyancy in sodium. The study shows that a single collection tray is capable of removing up to 20 MW decay heat load in a typical 500 MWe pool type SFR. Further, studies are carried out to improve the natural circulation of sodium around the source, in the lower plenum and to distribute core debris of the whole core to multiple collection trays. It is found that the double and triple collection trays can accommodate decay loads up to 29 MW. Provision of openings in the collection trays has proved to be effective in improving the heat transfer and sodium flow as well as in distributing the core debris to the

Loss of coolant accident mitigation for liquid metal cooled space reactors

International Nuclear Information System (INIS)

Georgevich, Vladimir; Best, Frederick; Erdman, Carl

1989-01-01

A loss of coolant accident (LOCA) in a liquid metal-cooled space reactor system has been considered as a possible accident scenario. Development of new concepts that will prevent core damage by LOCA caused elevated temperatures is the primary motivation of this work. Decay heat generated by the fission products in the reactor core following shutdown is sufficiently high to melt the fuel unless energy can be removed from the pins at a sufficiently rapid rate. There are two major reasons that prevent utilization of traditional emergency cooling methods. One is the absence of gravity and the other is the vacuum condition outside the reactor vessel. A concept that overcomes both problems is the Saturated Wick Evaporation Method (SWEM). This method involves placing wicking structures at specific locations in the core to act as energy sinks. One of its properties is the isothermal behaviour of the liquid in the wick. The absorption of energy by the surface at the isothermal temperature will direct the energy into an evaporation process and not in sensible heat addition. The use of this concept enables establishment of isothermal positions within the core. A computer code that evaluates the temperature distribution of the core has been developed and the results show that this design will prevent fuel meltdown. (author)

Evaluation of downmotion time interval molten materials to core catcher during core disruptive accidents postulated in LMFR

International Nuclear Information System (INIS)

Voronov, S.A.; Kiryushin, A.I.; Kuzavkov, N.G.; Vlasichev, G.N.

1994-01-01

Hypothetical core disruptive accidents are postulated to clear potential of a reactor plant to withstand extreme conditions and to generate measures for management and mitigation of accidents consequence. In Russian advanced reactors there is a core catcher below the diagrid to prevent vessel bottom melting and to localize fuel debris. In this paper the calculation technique and estimation of relocation time of molten fuel and materials are presented in the case of core disruptive accidents postulated for LMFR reactor. To evaluate minimum interval of fuel relocation time the calculations for different initial data are provided. Large mass of materials between the core and the catcher in LMFR reactor hinders molten materials relocation toward the vessel bottom. That condition increases the time interval of reaching core catcher by molten fuel. Computations performed allowed to evaluate the minimum molten materials relocation time from the core to the core catcher. This time interval is in a range of 3.5-5.5 hours. (author)

Analysis of severe core damage accident progression for the heavy water reactor

International Nuclear Information System (INIS)

Tong Lili; Yuan Kai; Yuan Jingtian; Cao Xuewu

2010-01-01

In this study, the severe accident progression analysis of generic Canadian deuterium uranium reactor 6 was preliminarily provided using an integrated severe accident analysis code. The selected accident sequences were multiple steam generator tube rupture and large break loss-of-coolant accidents because these led to severe core damage with an assumed unavailability for several critical safety systems. The progressions of severe accident included a set of failed safety systems normally operated at full power, and initiative events led to primary heat transport system inventory blow-down or boil off. The core heat-up and melting, steam generator response,fuel channel and calandria vessel failure were analyzed. The results showed that the progression of a severe core damage accident induced by steam generator tube rupture or large break loss-of-coolant accidents in a CANDU reactor was slow due to heat sinks in the calandria vessel and vault. (authors)

Nuclear power reactor core melt accidents. Current State of Knowledge

International Nuclear Information System (INIS)

Jacquemain, Didier; Cenerino, Gerard; Corenwinder, Francois; Raimond, Emmanuel IRSN; Bentaib, Ahmed; Bonneville, Herve; Clement, Bernard; Cranga, Michel; Fichot, Florian; Koundy, Vincent; Meignen, Renaud; Corenwinder, Francois; Leteinturier, Denis; Monroig, Frederique; Nahas, Georges; Pichereau, Frederique; Van-Dorsselaere, Jean-Pierre; Couturier, Jean; Debaudringhien, Cecile; Duprat, Anna; Dupuy, Patricia; Evrard, Jean-Michel; Nicaise, Gregory; Berthoud, Georges; Studer, Etienne; Boulaud, Denis; Chaumont, Bernard; Clement, Bernard; Gonzalez, Richard; Queniart, Daniel; Peltier, Jean; Goue, Georges; Lefevre, Odile; Marano, Sandrine; Gobin, Jean-Dominique; Schwarz, Michel; Repussard, Jacques; Haste, Tim; Ducros, Gerard; Journeau, Christophe; Magallon, Daniel; Seiler, Jean-Marie; Tourniaire, Bruno; Durin, Michel; Andreo, Francois; Atkhen, Kresna; Daguse, Thierry; Dubreuil-Chambardel, Alain; Kappler, Francois; Labadie, Gerard; Schumm, Andreas; Gauntt, Randall O.; Birchley, Jonathan

2015-11-01

For over thirty years, IPSN and subsequently IRSN has played a major international role in the field of nuclear power reactor core melt accidents through the undertaking of important experimental programmes (the most significant being the Phebus-FP programme), the development of validated simulation tools (the ASTEC code that is today the leading European tool for modelling severe accidents), and the coordination of the SARNET (Severe Accident Research Network) international network of excellence. These accidents are described as 'severe accidents' because they can lead to radioactive releases outside the plant concerned, with serious consequences for the general public and for the environment. This book compiles the sum of the knowledge acquired on this subject and summarises the lessons that have been learnt from severe accidents around the world for the prevention and reduction of the consequences of such accidents, without addressing those from the Fukushima accident, where knowledge of events is still evolving. The knowledge accumulated by the Institute on these subjects enabled it to play an active role in informing public authorities, the media and the public when this accident occurred, and continues to do so to this day. Following the introduction, which describes the structure of this book and highlights the objectives of R and D on core melt accidents, this book briefly presents the design and operating principles (Chapter 2) and safety principles (Chapter 3) of the reactors currently in operation in France, as well as the main accident scenarios envisaged and studied (Chapter 4). The objective of these chapters is not to provide exhaustive information on these subjects (the reader should refer to the general reference documents listed in the corresponding chapters), but instead to provide the information needed in order to understand, firstly, the general approach adopted in France for preventing and mitigating the consequences of core melt

Research work for improving LWR safety. 1991 annual report

International Nuclear Information System (INIS)

1992-08-01

The work performed in 1991 for the PNS project centers on various phenomena of severe fuel damage and on selected aspects of a core meltdown accident, relating to aerosol behaviour and filter engineering, and to methods of assessing and minimizing the radiological impacts of a reactor accident. One paper included in this annual report summarizes the evaluation of experiments carried out in 1990 at the Wuerenlingen PROTEUS reactor. The 1991 task programme of the project for the first time included research into extreme load conditions affecting the containment in a core meltdown accident; first results are given of the experiments performed. (orig./DG) [de

Method for consequence calculations for severe accidents

International Nuclear Information System (INIS)

Nielsen, F.; Thykier-Nielsn, S.

1987-03-01

This report was commissioned by the Swedish State Power Board. The report contains a calculation of radiation doses in the surroundings caused by a theoretical core meltdown accident at Forsmark reactor No 3. The assumption used for the calculations were a 0.06% release of iodine and cesium corresponding to a 0.1% release through the FILTRA plant at Barsebaeck. The calculations were made by means of the PLUCON4 code. Meteorological data for two years from the Forsmark meteorological tower were analysed to find representative weather situations. As typical weather pasquill D was chosen with wind speed 5 m/s, and as extreme weather, Pasquill F with wind speed 2 m/s. 23 tabs., 36 ills., 21 refs. (author)

Safety analysis of a stratified reactor foundation subject to core meltdown

International Nuclear Information System (INIS)

Laermann, K.H.; Berhalter, D.; Wieching, G.

1983-01-01

Comprehensive calculations were made to examine a foundation plate under static load with non-linear material behaviour. In particular, deformation and crack behaviour of the plate were observed. The calculations hereunder, made to calculate the time of rupture of the plate with the foundation exposed to high temperatures, with and without cavity formation, prove that high temperatures are not as relevant as the melt-down of the layers of armour on top of the middle of the plate. The consequences of this survey are: to protect the top armour of the plate centre and not to use it as support for any structural components. This free space could then be used to instal said multi-layer plate. (orig./HP) [de

Implications for accident management of adding water to a degrading reactor core

International Nuclear Information System (INIS)

Kuan, P.; Hanson, D.J.; Pafford, D.J.; Quick, K.S.; Witt, R.J.

1994-02-01

This report evaluates both the positive and negative consequences of adding water to a degraded reactor core during a severe accident. The evaluation discusses the earliest possible stage at which an accident can be terminated and how plant personnel can best respond to undesired results. Specifically discussed are (a) the potential for plant personnel to add water for a range of severe accidents, (b) the time available for plant personnel to act, (c) possible plant responses to water added during the various stages of core degradation, (d) plant instrumentation available to understand the core condition and (e) the expected response of the instrumentation during the various stages of severe accidents

Implications for accident management of adding water to a degrading reactor core

Energy Technology Data Exchange (ETDEWEB)

Kuan, P.; Hanson, D.J.; Pafford, D.J.; Quick, K.S.; Witt, R.J. [EG and G Idaho, Inc., Idaho Falls, ID (United States)

1994-02-01

This report evaluates both the positive and negative consequences of adding water to a degraded reactor core during a severe accident. The evaluation discusses the earliest possible stage at which an accident can be terminated and how plant personnel can best respond to undesired results. Specifically discussed are (a) the potential for plant personnel to add water for a range of severe accidents, (b) the time available for plant personnel to act, (c) possible plant responses to water added during the various stages of core degradation, (d) plant instrumentation available to understand the core condition and (e) the expected response of the instrumentation during the various stages of severe accidents.

ILK statement on the consequences of the Chernobyl accident. Taking stock after twenty years

International Nuclear Information System (INIS)

2006-01-01

The Chernobyl reactor accident was the consequence of a reactor design which was not inherently safe, and of a lack of 'safety culture'. The RBMK-type reactor (a Russian graphite-moderated light water reactor design: reaktor bolshoi moshnosty kanalny=high-power channel reactor) had not been designed to a satisfactory safety level, and the operating staff were not informed on the weak spots in plant design. The combination of these factors caused the worst nuclear accident, completely destroying the reactor. The consequences may be seen as the product of two severe accidents superimposed upon each other: the explosion of the reactor, and core melt-down associated with an intense, persistent fire of the graphite moderator. The Statement contains analyses of these points: Release, Propagation and Deposition of Radioactive Materials; Protective Measures; Impact on the Environment and Agriculture; Assessment of Radiation Exposure; Health Impact; Psychological and Societal Impacts; Potential Residual Risks. (orig.)

Thermal and stress analyses of meltdown cups for LMFBR safety experiments using SLSF in-reactor loops

International Nuclear Information System (INIS)

Blomquist, C.A.; Pierce, R.D.; Pedersen, D.R.; Ariman, T.

1977-01-01

The test trains for the Sodium Loop Safety Facility (SLSF) in-reactor experiments, which simulate hypothetical LMFBR accidents, have a meltdown cup to protect the primary containment from the effects of molten materials. Thermal and stress analyses were performed on the cup which is designed to contain 3.6 kg of molten fuel and 2.4 kg of molten steel. Thermal analyses were performed with the Argonne-modified version fo the general heat transfer code THTB, based on the instantaneous addition of 3200 0 K molten fuel with a decay heat of 9 W/gm and 1920 0 K molten steel. These analyses have shown that the cup will adequately cool the molten materials. The stress analysis showed that the Inconel vessel would not fail from the pressure loading, it was also shown that brittle fracture of the tungsten liner from thermal gradients is unlikely. Therefore, the melt-down cup meets the structural design requirements. (Auth.)

Case for integral core-disruptive accident analysis

International Nuclear Information System (INIS)

Luck, L.B.; Bell, C.R.

1985-01-01

Integral analysis is an approach used at the Los Alamos National Laboratory to cope with the broad multiplicity of accident paths and complex phenomena that characterize the transition phase of core-disruptive accident progression in a liquid-metal-cooled fast breeder reactor. The approach is based on the combination of a reference calculation, which is intended to represent a band of similar accident paths, and associated system- and separate-effect studies, which are designed to determine the effect of uncertainties. Results are interpreted in the context of a probabilistic framework. The approach was applied successfully in two studies; illustrations from the Clinch River Breeder Reactor licensing assessment are included

Simulation experiments concerning core meltdown

International Nuclear Information System (INIS)

Werle, H.

1979-01-01

A gas stream causes a remarkable increase in the interfacial heat flux (by a factor of 8 for v = 0.63 cm/s, v = gas volume flux/horizontal area). The most important characteristics of the system investigated (silicon oil/wood metal) are relatively similar to those of a core melt, Therefore a remarkable increase of the interfacial heat transfer by the gas release may be expected also for a core melt, compared with earlier investigations at the system silicon oil/water the influence of a gas stream is nevertheless remarkably lower for silicon oil/wood metal. This shows that the density ratio plays an important role. (orig./RW) [de

Application of nanofluids to mitigation of severe accident at the Fukushima Daiichi Nuclear Power Plant

International Nuclear Information System (INIS)

Suh, Kune Y.

2011-01-01

This paper presents the pivotal thermohydrodynamic and neutronic characteristics of nanofluids as an alternative coolant for boiling water reactors (BWRs) during the abnormal operation including, but not necessarily limited to, severe accident involving meltdown as well as potentially melt-through of the reactor core material. Results indicate that the benefit of utilizing nanoparticles in the BWR working fluid appears to be minimal during the nominal operation since the nanoparticles tend to carry over to the turbine and condenser lending themselves to erosion and fouling concerns. Good news, on the other hand, is that exploitation of nanofluids during the decay heat removal condition in case of an accident is promising indeed because of their high thermal conductivity and their neutron poisoning effect. Thermohydrodynamic and neutronic investigations are in progress to streamline the nanoparticles and to optimize their concentration during the abnormal operation beyond the conventional design basis extending to severe accident. (author)

Core loss during a severe accident (COLOSS)

International Nuclear Information System (INIS)

Adroguer, B.; Bertrand, F.; Chatelard, P.; Cocuaud, N.; Van Dorsselaere, J.P.; Bellenfant, L.; Knocke, D.; Bottomley, D.; Vrtilkova, V.; Belovsky, L.; Mueller, K.; Hering, W.; Homann, C.; Krauss, W.; Miassoedov, A.; Schanz, G.; Steinbrueck, M.; Stuckert, J.; Hozer, Z.; Bandini, G.; Birchley, J.; Berlepsch, T. von; Kleinhietpass, I.; Buck, M.; Benitez, J.A.F.; Virtanen, E.; Marguet, S.; Azarian, G.; Caillaux, A.; Plank, H.; Boldyrev, A.; Veshchunov, M.; Kobzar, V.; Zvonarev, Y.; Goryachev, A.

2005-01-01

The COLOSS project was a 3-year shared-cost action, which started in February 2000. The work-programme performed by 19 partners was shaped around complementary activities aimed at improving severe accident codes. Unresolved risk-relevant issues regarding H 2 production, melt generation and the source term were studied through a large number of experiments such as (a) dissolution of fresh and high burn-up UO 2 and MOX by molten Zircaloy (b) simultaneous dissolution of UO 2 and ZrO 2 (c) oxidation of U-O-Zr mixtures (d) degradation-oxidation of B 4 C control rods. Corresponding models were developed and implemented in severe accident computer codes. Upgraded codes were then used to apply results in plant calculations and evaluate their consequences on key severe accident sequences in different plants involving B 4 C control rods and in the TMI-2 accident. Significant results have been produced from separate-effects, semi-global and large-scale tests on COLOSS topics enabling the development and validation of models and the improvement of some severe accident codes. Breakthroughs were achieved on some issues for which more data are needed for consolidation of the modelling in particular on burn-up effects on UO 2 and MOX dissolution and oxidation of U-O-Zr and B 4 C-metal mixtures. There was experimental evidence that the oxidation of these mixtures can contribute significantly to the large H 2 production observed during the reflooding of degraded cores under severe accident conditions. The plant calculation activity enabled (a) the assessment of codes to calculate core degradation with the identification of main uncertainties and needs for short-term developments and (b) the identification of safety implications of new results. Main results and recommendations for future R and D activities are summarized in this paper

Melt propagation in dry core debris beds

International Nuclear Information System (INIS)

Dosanjh, S.S.

1989-01-01

During severe light water reactor accidents like Three Mile Island Unit 2, the fuel rods can fragment and thus convert the reactor core into a large particle bed. The postdryout meltdown of such debris beds is examined. A two-dimensional model that considers the presence of oxidic (UO 2 and ZrO 2 ) as well as metallic (e.g., zirconium) constituents is developed. Key results are that a dense metallic crust is created near the bottom of the bed as molten materials flow downward and freeze; liquid accumulates above the blockage and, if zirconium is present, the pool grows rapidly as molten zirconium dissolved both UO 2 and ZrO 2 particles; if the melt wets the solid, a fraction of the melt flows radially outward under the action of capillary forces and freezes near the radial boundary; in a nonwetting system, all of the melt flows into the bottom of the bed; and when zirconium and iron are in intimate contact and the zirconium metal atomic fraction is > 0.33, these metals can liquefy and flow out of the bed very early in the meltdown sequence

German risk study nuclear power plants, phase B

International Nuclear Information System (INIS)

1990-01-01

The book documents the results of the probabilistic safety analysis performed at the Biblis-B reference plant. It covers 1) result course analyses and reliability analyses of loss of coolant accidents and transients without and with regard to on-site emergency measures; 2) event tree analyses of on-site and off-site events; 3) analyses of the function of the safety tank in the case of core meltdown accidents, and of the release of fission products into the environment in such case. The probability of a core meltdown is about 3-4 to 100,000 per year and plant. (HP) [de

ADAM: An Accident Diagnostic,Analysis and Management System - Applications to Severe Accident Simulation and Management

International Nuclear Information System (INIS)

Zavisca, M.J.; Khatib-Rahbar, M.; Esmaili, H.; Schulz, R.

2002-01-01

The Accident Diagnostic, Analysis and Management (ADAM) computer code has been developed as a tool for on-line applications to accident diagnostics, simulation, management and training. ADAM's severe accident simulation capabilities incorporate a balance of mechanistic, phenomenologically based models with simple parametric approaches for elements including (but not limited to) thermal hydraulics; heat transfer; fuel heatup, meltdown, and relocation; fission product release and transport; combustible gas generation and combustion; and core-concrete interaction. The overall model is defined by a relatively coarse spatial nodalization of the reactor coolant and containment systems and is advanced explicitly in time. The result is to enable much faster than real time (i.e., 100 to 1000 times faster than real time on a personal computer) applications to on-line investigations and/or accident management training. Other features of the simulation module include provision for activation of water injection, including the Engineered Safety Features, as well as other mechanisms for the assessment of accident management and recovery strategies and the evaluation of PSA success criteria. The accident diagnostics module of ADAM uses on-line access to selected plant parameters (as measured by plant sensors) to compute the thermodynamic state of the plant, and to predict various margins to safety (e.g., times to pressure vessel saturation and steam generator dryout). Rule-based logic is employed to classify the measured data as belonging to one of a number of likely scenarios based on symptoms, and a number of 'alarms' are generated to signal the state of the reactor and containment. This paper will address the features and limitations of ADAM with particular focus on accident simulation and management. (authors)

Reactor safety study. An assessment of accident risks in U.S. commercial nuclear power plants. Appendices VII, VIII, IX, and X

International Nuclear Information System (INIS)

1975-10-01

Information is presented concerning the release of radioactivity in reactor accidents; physical processes in reactor meltdown accidents; safety design rationale for nuclear power plants; and design adequacy

The risk of a major nuclear accident: calculation and perception of probabilities

International Nuclear Information System (INIS)

Leveque, Francois

2013-07-01

The accident at Fukushima Daiichi, Japan, occurred on 11 March 2011. This nuclear disaster, the third on such a scale, left a lasting mark in the minds of hundreds of millions of people. Much as Three Mile Island or Chernobyl, yet another place will be permanently associated with a nuclear power plant which went out of control. Fukushima Daiichi revived the issue of the hazards of civil nuclear power, stirring up all the associated passion and emotion. The whole of this paper is devoted to the risk of a major nuclear accident. By this we mean a failure initiating core meltdown, a situation in which the fuel rods melt and mix with the metal in their cladding. Such accidents are classified as at least level 5 on the International Nuclear Event Scale. The Three Mile Island accident, which occurred in 1979 in the United States, reached this level of severity. The explosion of reactor 4 at the Chernobyl plant in Ukraine in 1986 and the recent accident in Japan were classified as class 7, the highest grade on this logarithmic scale. The main difference between the top two levels and level 5 relates to a significant or major release of radioactive material to the environment. In the event of a level-5 accident, damage is restricted to the inside of the plant, whereas, in the case of level-7 accidents, huge areas of land, above or below the surface, and/or sea may be contaminated. Before the meltdown of reactors 1, 2 and 3 at Fukushima Daiichi, eight major accidents affecting nuclear power plants had occurred worldwide. This is a high figure compared with the one calculated by the experts. Observations in the field do not appear to fit the results of the probabilistic models of nuclear accidents produced since the 1970's. Oddly enough the number of major accidents is closer to the risk as perceived by the general public. In general we tend to overestimate any risk relating to rare, fearsome accidents. What are we to make of this divergence? How are we to reconcile

KATS experiments to simulate corium spreading in the EPR core catcher concept

International Nuclear Information System (INIS)

Eppinger, B.; Fieg, G.; Schuetz, W.; Stegmaier, U.

2001-01-01

In future Light Water Reactors special devices (core catchers) might be required to prevent containment failure by basement erosion after reactor pressure vessel melt-through during a core meltdown accident. Quick freezing of the molten core masses is desirable to reduce release of radioactivity. Several concepts of core catcher de-vices have been proposed based on the spreading of corium melt onto flat surfaces with subsequent cooling by flooding with water. Therefore a series of experiments to investigate high temperature melt spreading on flat surfaces has been carried out using alumina-iron thermite melts as a simulant. The oxidic thermite melt is conditioned by adding other oxides to simulate a realistic corium melt as close as possible. Spreading of oxidic and metallic melts have been performed in one- and two-dimensional geometry. Substrates were chemically inert ceramic layers, dry concrete and concrete with a shallow water layer on top. (authors)

High enrichment to low enrichment core's conversion. Accidents analysis

International Nuclear Information System (INIS)

Abbate, P.; Rubio, R.; Doval, A.; Lovotti, O.

1990-01-01

This work analyzes the different accidents that may occur in the reactor's facility after the 20% high-enriched uranium core's conversion. The reactor (of 5 thermal Mw), built in the 50's and 60's, is of the 'swimming pool' type, with light water and fuel elements of the curve plates MTR type, enriched at 93.15 %. This analysis includes: a) accidents by reactivity insertion; b) accidents by coolant loss; c) analysis by flow loss and d) fission products release. (Author) [es

Theoretical and experimental methods to determine the properties of molten core components and reaction products. Pt. 2

International Nuclear Information System (INIS)

Nazare, S.; Ondracek, G.; Schulz, B.

1975-10-01

In the course of a loss of coolant accident, a sequence of events would be initiated that ultimately could lead to core melting. The course of these events and the consequences of core meltdown would in part be determined by the properties of the core materials and the products of their interaction. On the basis of available theoretical and experimental results, the report attempts an estimation of properties such as: 1) work of adhesion between UO 2 - and (U,Zr) liquid phase, 2) heat of fusion of some melts, 3) heat capacity of liquid reaction products, 4) viscosity of liquid reaction products, 5) thermal conductivity of liquid reaction products. Experimental work is suggested for those cases, where the estimates need to be improved or verified. (orig.) [de

Role of fission product in whole core accidents: research in the USA

International Nuclear Information System (INIS)

Jackson, J.F.; Deitrich, L.W.

1977-01-01

The techniques being developed in the United States for analyzing postulated whole-core accidents in LMFBRs are briefly reviewed. The key mechanistic analysis methods are discussed in detail. Important research projects in the area of fission product effects are examined. Some typical results on the role of fission products in whole-core accidents are presented

Simulation experiment on the flooding behaviour of core melts: KATS-9

International Nuclear Information System (INIS)

Fieg, G.; Massier, H.; Schuetz, W.; Stegmaier, U.; Stern, G.

2000-11-01

For future Light Water Reactors special devices (core catchers) are being developed to prevent containment failure by basement erosion after reactor pressure vessel meltthrough during a core meltdown accident. Quick freezing of the molten core masses is desirable to reduce release of radioactivity. Several concepts of core catcher devices have been proposed based on the spreading of corium melt onto flat surfaces with subsequent water cooling. A KATS-experiment has been performed to investigate the flooding behaviour of high temperature melts using alumina-iron thermite melts as a simulant. The oxidic thermite melt is conditioned by adding other oxides to simulate a realistic corium melt as close as possible in terms of liquidus and solidus temperatures. Before flooding with water, spreading of the separate oxidic and metallic melts has been done in one-dimensional channels with a silicate concrete as the substrate. The flooding rate was, in relation to the melt surface, identical to the flooding rate in EPR. (orig.) [de

The Fukushima accident

International Nuclear Information System (INIS)

Maqua, M.; Stueck, R.

2012-01-01

On 11 March 2011, the Tohoku earthquake and the subsequent tsunami hit the Japanese east coast, causing more than 15,000 fatalities. To this date, 3,000 people are still missing. The Fukushima Dai-ichi NPP was the nuclear installation that was most affected by the tsunami. The earthquake cut off the NPP from the national grid. About 45 minutes later, the tsunami flooded units 1-4 and led to core meltdown events with large releases for units 1, 2 and 3. Unit 4 had been in refuelling outage at that time and lost the cooling of the spent fuel pool for several days. Considerable hydrogen explosions occurred in units 1, 3 and 4. Shortly after the accident, TEPCO started to mitigate the consequences of the accident by providing external cooling to the reactors and by removing the radioactive debris from the site. Great emphasis was laid on effective radiation protection measures for the clean-up workers. Thus, up to now there has been no fatality due to the radiation caused by the Fukushima accident. The main steps of the accident sequences are described, taking into account the latest findings of investigations performed by TEPCO or on behalf of the regulatory body. The presentation focuses on the description of the status of the Fukushima Dai-ichi nuclear power plant and the future steps for cleaning-up the site. In the presentation, the major phases of the roadmap that TEPCO has developed for the clean-up are highlighted. The risks associated with the current plant status and the clean-up phases are described. Abstract the content of the manuscript in a few lines.

RBMK-1500 accident management for loss of long-term core cooling

International Nuclear Information System (INIS)

Uspuras, E.; Kaliatka, A.

2001-01-01

Results of the Level 1 probabilistic safety assessment of the Ignalina NPP has shown that in topography of the risk, transients dominate above the accidents with LOCAs and failure of the core long-term cooling are the main factors to frequency of the core damage. Previous analyses have shown, that after initial event, as a rule, the reactivity control, as well as short-term and intermediate cooling are provided. However, the acceptance criteria of the long-term cooling are not always carried out. It means that from this point of view the most dangerous accident scenarios are the scenarios related to loss of the core long-term cooling. On the other hand, the transition to the core condition due to loss of the long-term cooling specifies potential opportunities for the management of the accident consequences. Hence, accident management for the mitigation of the accident consequences should be considered and developed. The most likely initiating event, which probably leads to the loss of long term cooling accident, is station blackout. The station blackout is the loss of normal electrical power supply for local needs with an additional failure on start-up of all diesel generators. In the case of loss of electrical power supply MCPs, the circulating pumps of the service water system and MFWPs are switched-off. At the same time, TCV of both turbines are closed. Failure of diesel generators leads to the non-operability of the ECCS long-term cooling subsystem. It means the impossibility to feed MCC by water. The analysis of the station blackout for Ignalina NPP was performed using RELAP5 code. (author)

Release fraction of PWR after severe accidents. Vol. 4

Energy Technology Data Exchange (ETDEWEB)

Aziz, M; El-Messeiry, A M [National Center for Nuclear Safety and Radiation Control, Atomic Energy Authority, Cairo (Egypt)

1996-03-01

Fission fragments and gases are emitted after accidents as a result of core meltdown and core concrete interactions. These aerosols are transported and fill the reactor containment. With increasing the pressure above pressure design bases, a failure of containment may occur and subsequently these aerosols will release into the external environment leading to a source term of radioactivity that affects the safety of workers and public. The amount of aerosol which escapes to the environment can be described by the release fraction which is defined as the total accumulated aerosol which initially enters the containment. The factors that affect the release fraction is studied, and the aerosol dynamics equation is used to model the release of aerosol to the outside atmosphere. These factors are containment pressure, failure time,break area, the size of aerosol particle. It found that early failure time and higher pressure increase the release fraction, also the release faction is affected by the area and the aerosol particle size. 7 figs., 2 tabs.

Release fraction of PWR after severe accidents. Vol. 4

International Nuclear Information System (INIS)

Aziz, M.; El-Messeiry, A.M.

1996-01-01

Fission fragments and gases are emitted after accidents as a result of core meltdown and core concrete interactions. These aerosols are transported and fill the reactor containment. With increasing the pressure above pressure design bases, a failure of containment may occur and subsequently these aerosols will release into the external environment leading to a source term of radioactivity that affects the safety of workers and public. The amount of aerosol which escapes to the environment can be described by the release fraction which is defined as the total accumulated aerosol which initially enters the containment. The factors that affect the release fraction is studied, and the aerosol dynamics equation is used to model the release of aerosol to the outside atmosphere. These factors are containment pressure, failure time,break area, the size of aerosol particle. It found that early failure time and higher pressure increase the release fraction, also the release faction is affected by the area and the aerosol particle size. 7 figs., 2 tabs

The Chernobyl reactor accident. Pt. 1 and 2

International Nuclear Information System (INIS)

1986-06-01

The report first summarizes the available information on the various incidents of the whole accident scenario, and combines the information to present a first general outline and a basis for appraisal. The most significant incidents reported, namely power excursion, core meltdown, and fire, are discussed with a view to the reactor design and safety of reactors installed in the FRG. The main differences and advantages of German reactor designs are shown, as e.g.: Power excursions are mastered by inherent physical conditions; far better redundancy of engineered safety systems; enclosure of the complete reactor cooling system in a pressure-retaining steel containment; reactor buildings being made of reinforced concrete. The second part of the report deals with the radiological effects to be expected for our country. Data are given on the varying radiological exposure of the different regions. The fate and uptake of radioactivity in the human body are discussed. The conclusion drawn from the data presented is that the individual exposure due to the reactor accident will remain within the variations and limits of natural radioactivity and effects. (orig./HP) [de

analysis of reactivity accidents in MTR for various protection system parameters and core condition

International Nuclear Information System (INIS)

Mohamed, F.M.

2011-01-01

Egypt Second Research Reactor (ETRR-2) core was modified to irradiate LEU (Low Enriched Uranium) plates in two irradiation boxes for fission 99 Mo production. The old core comprising 29 fuel elements and one Co Irradiation Device (CID) and the new core comprising 27 fuel elements, CID, and two 99 Mo production boxes. The in core irradiation has the advantage of no special cooling or irradiation loop is required. The purpose of the present work is the analysis of reactivity accidents (RIA) for ETRR-2 cores. The analysis was done to evaluate the accidents from different point of view:1- Analysis of the new core for various Reactor Protection System (RPS) parameters 2- Comparison between the two cores. 3- Analysis of the 99 Mo production boxes.PARET computer code was employed to compute various parameters. Initiating events in RIA involve various modes of reactivity insertion, namely, prompt critical condition (p=1$), accidental ejection of partial and complete CID uncontrolled withdrawal of a control rod accident, and sudden cooling of the reactor core. The time histories of reactor power, energy released, and the maximum fuel, clad and coolant temperatures of fuel elements and LEU plates were calculated for each of these accidents. The results show that the maximum clad temperatures remain well below the clad melting of both fuel and uranium plates during these accidents. It is concluded that for the new core, the RIA with scram will not result in fuel or uranium plate failure.

Transport-diffusion comparisons for small core LMFBR disruptive accidents

International Nuclear Information System (INIS)

Tomlinson, E.T.

1977-11-01

A number of numerical experiments were performed to assess the validity of diffusion theory for calculating the reactivity state of various small core LMFBR disrupted geometries. The disrupted configurations correspond, in general, to various configurations predicted by SAS3A for transient undercooling (TUC) and transient overpower (TOP) accidents for homogeneous cores and to the ZPPR-7 configurations for heterogeneous core. In all TUC cases diffusion theory was shown to be inadequate for the calculation of reactivity changes during core disassembly

Reactor safety study. An assessment of accident risks in U. S. commercial nuclear power plants. Appendices VII, VIII, IX, and X. [PWR and BWR

Energy Technology Data Exchange (ETDEWEB)

1975-10-01

Information is presented concerning the release of radioactivity in reactor accidents; physical processes in reactor meltdown accidents; safety design rationale for nuclear power plants; and design adequacy.

Brookhaven lecture series No. 227: The Chernobyl accident

International Nuclear Information System (INIS)

Kouts, H.

1986-01-01

This lecture discusses the events leading to, during, and following the Chernobyl Reactor number 4 accident. A description of the light water cooled, graphite moderated reactor, the reactor site conditions leading to meltdown is presented. The emission of radioactive effluents and the biological radiation effects is also discussed. (FI)

Eigen's Error Threshold and Mutational Meltdown in a Quasispecies Model

OpenAIRE

Bagnoli, F.; Bezzi, M.

1998-01-01

We introduce a toy model for interacting populations connected by mutations and limited by a shared resource. We study the presence of Eigen's error threshold and mutational meltdown. The phase diagram of the system shows that the extinction of the whole population due to mutational meltdown can occur well before an eventual error threshold transition.

Four-fluid model of PWR degraded cores

International Nuclear Information System (INIS)

Dearing, J.F.

1985-01-01

This paper describes the new two-dimensional, four-fluid fluid dynamics and heat transfer (FLUIDS) module of the MELPROG code. MELPROG is designed to give an integrated, mechanistic treatment of pressurized water reactor (PWR) core meltdown accidents from accident initiation to vessel melt-through. The code has a modular data storage and transfer structure, with each module providing the others with boundary conditions at each computational time step. Thus the FLUIDS module receives mass and energy source terms from the fuel pin module, the structures module, and the debris bed module, and radiation energy source terms from the radiation module. MELPROG, which models the reactor vessel, is also designed to model the vessel as a component in the TRAC/PF1 networking solution of a PWR reactor coolant system (RCS). The coupling between TRAC and MELPROG is implicit in the fluid dynamics of the reactor coolant (liquid water and steam) allowing an accurate simulation of the coupling between the vessel and the rest of the RCS during an accident. This paper deals specifically with the numerical model of fluid dynamics and heat transfer within the reactor vessel, which allows a much more realistic simulation (with less restrictive assumptions on physical behavior) of the accident than has been possible before

Summary of treat experiments on oxide core-disruptive accidents

International Nuclear Information System (INIS)

Dickerman, C.E.; Rothman, A.B.; Klickman, A.E.; Spencer, B.W.; DeVolpi, A.

1979-02-01

A program of transient in-reactor experiments is being conducted by Argonne National Laboratory in the Transient Reactor Test (TREAT) facility to guide and support analyses of hypothetical core-disruptive accidents (HCDA) in liquid-metal fast breeder reactors (LMFBR). Test results provide data needed to establish the response of LMFBR cores to hypothetical accidents producing fuel failure, coolant boiling, and the movement of coolant, molten fuel, and molten cladding. These data include margins to fuel failure, the modes of failure and movements, and evidence for identification of the mechanisms which determine the failure and movements. A key element in the program is the fast-neutron hodoscope, which detects fuel movement as a function of time during experiments

Reactor Core Coolability Analysis during Hypothesized Severe Accidents of OPR1000

International Nuclear Information System (INIS)

Lee, Yongjae; Seo, Seungwon; Kim, Sung Joong; Ha, Kwang Soon; Kim, Hwan-Yeol

2014-01-01

Assessment of the safety features over the hypothesized severe accidents may be performed experimentally or numerically. Due to the considerable time and expenditures, experimental assessment is implemented only to the limited cases. Therefore numerical assessment has played a major role in revisiting severe accident analysis of the existing or newly designed power plants. Computer codes for the numerical analysis of severe accidents are categorized as the fast running integral code and detailed code. Fast running integral codes are characterized by a well-balanced combination of detailed and simplified models for the simulation of the relevant phenomena within an NPP in the case of a severe accident. MAAP, MELCOR and ASTEC belong to the examples of fast running integral codes. Detailed code is to model as far as possible all relevant phenomena in detail by mechanistic models. The examples of detailed code is SCDAP/RELAP5. Using the MELCOR, Carbajo. investigated sensitivity studies of Station Black Out (SBO) using the MELCOR for Peach Bottom BWR. Park et al. conduct regulatory research of the PWR severe accident. Ahn et al. research sensitivity analysis of the severe accident for APR1400 with MELCOR 1.8.4. Lee et al. investigated RCS depressurization strategy and developed a core coolability map for independent scenarios of Small Break Loss-of-Coolant Accident (SBLOCA), SBO, and Total Loss of Feed Water (TLOFW). In this study, three initiating cases were selected, which are SBLOCA without SI, SBO, and TLOFW. The initiating cases exhibit the highest probability of transitioning into core damage according to PSA 1 of OPR 1000. The objective of this study is to investigate the reactor core coolability during hypothesized severe accidents of OPR1000. As a representative indicator, we have employed Jakob number and developed JaCET and JaMCT using the MELCOR simulation. Although the RCS pressures for the respective accident scenarios were different, the JaMCT and Ja

Oxidation during reflood of reactor core with melting cladding

Energy Technology Data Exchange (ETDEWEB)

Siefken, L.J.; Allison, C.M.; Davis, K.L. [and others

1995-09-01

Models were recently developed and incorporated into the SCDAP/RELAP5 code for calculating the oxidation of fuel rods during cladding meltdown and reflood. Experiments have shown that a period of intense oxidation may occur when a hot partially oxidized reactor core is reflooded. This paper offers an explanation of the cladding meltdown and oxidation processes that cause this intense period of oxidation. Models for the cladding meltdown and oxidation processes are developed. The models are assessed by simulating a severe fuel damage experiment that involved reflood. The models for cladding meltdown and oxidation were found to improve calculation of the temperature and oxidation of fuel rods during the period in which hot fuel rods are reflooded.

Large population center and core melt accident considerations in siting

International Nuclear Information System (INIS)

Camarinopoulos, L.; Yadigaroglu, G.

1983-01-01

The problem of providing suitable demographic siting criteria in the presence of a very large population center in an otherwise sparsely populated region is addressed. Simple calculations were performed making maximum use of pretabulated results of studies where core melt accidents are considered. These show that taking into consideration the air flow patterns in the region can lower the expected population doses from core melt accidents more effectively than distance alone. Expected doses are compared to the annual background radiation dose. A simple siting criterion combining geographical considerations with the probability of a release reaching the large population center is proposed

Safety oriented LWR research. Annual report 1990

International Nuclear Information System (INIS)

1991-07-01

The contributions describe phenomenons of severe fuel damage and aspects of core meltdown accidents. These accidents deal with aerosol behaviour and ventilation systems and the methods for assessing and reducing the radiological concequences of nuclear accidents. Other contributions describe selected questions of safety of HCLWR type reactors. (DG)

The role of fission product in whole core accidents - research in the USA

Energy Technology Data Exchange (ETDEWEB)

Dietrich, L W [Argonne National Laboratory, Division of Reactor Analysis and Safety, Argonne, IL (United States); Jackson, J F [Los Alamos Scientific Laboratory, Q Division - Energy, Los Alamos, NM (United States)

1977-07-01

Safety of nuclear reactors has been a central concern of the nuclear energy industry from the very beginning. This concern, and the resultant excellence of design, fabrication, and operation, aided by extensive engineered safety features, has given nuclear energy its superior record of protection of the environment and of the public health and safety. With respect to the fast reactor, it was recognized early in the programme that there exists a theoretical possibility of a core compaction leading to significant energy release. Early analysis of this problem employed a number of conservative assumptions in attempting to bound the energy release. As reactors have grown in size, the suitability of such bounding calculations has diminished, and research into hypothetical accident analysis has emphasized a more mechanistic approach. In the USA, much effort has been directed towards modeling and computer code development aimed at following the course of an accident from its initiation to its ultimate conclusion with a stable, permanently subcritical, coolable core geometry, along with considerations of post-accident heat removal and radiological consequence assessment. Throughout this effort, the potential role of fission products has been recognized and account taken of the effects of fission products in determining accident progression. It is important to recognize that reactor safety is a very diverse topic, requiring consideration of a number of factors. While the major questions of public risk appear to be related to the hypothetical core disruptive accident (HCDA), it is necessary that the probability of having such an accident be extremely low In order that acceptable public risk be demonstrated. Such a demonstration requires sound engineering design and Implementation, with high standards of reliability, inspectability, maintainability, and operation, along with the requisite quality control and assurance. Tile current approach, typified by that taken by the

Sensitivity Analysis of Core Damage from Reactor Coolant Pump Seal Leakage during Extended Loss of All AC Power

Energy Technology Data Exchange (ETDEWEB)

Park, Da Hee; Kim, Min Gi; Lee, Kyung Jin; Hwang, Su hyun; Lee, Byung Chul [FNC Technology Co. Ltd., Yongin (Korea, Republic of); Yoon, Duk Joo; Lee, Seung Chan [Korea Hydro and Nuclear Power Co. Ltd., Daejeon (Korea, Republic of)

2015-10-15

In this study, in order to comprehend the Fukushima accident, the sensitivity analysis was performed to analyze the behavior of Reactor Coolant System (RCS) during ELAP using the RELAP5/MOD3.3 code. The Fukushima accident was caused by tsunami resulted in Station Black Out (SBO) followed by the reactor core melt-down and release of radioactive materials. After the accident, the equipment and strategies for the Extended Loss of All AC Power (ELAP) were recommended strongly. In this analysis, sensitivity studies for the RCP seal failure of the OPR1000 type NPP were performed by using RELAP5/MOD3.3 code. Six cases with different leakage rate of RCP seal were studied for ELAP with operator action or not. The main findings are summarized as follows: (1) Without the operator action, the core uncovery time is determined by the leakage rate of RCP seal. When the leakage rate per RCP seal are 5 gpm, 50 gpm, and 300 gpm respectively, the core uncovery time are 1.62 hr, 1.58 hr, and 1.29 hr respectively. Namely, If the leakage rate of RCP seal was much bigger, the uncover time of core would be shorter. (2) In case that the cooling by SG secondary side was performed using the TDAFP and SG ADV, the core uncovery time was significantly extended.

Safety evaluation of accident-tolerant FCM fueled core with SiC-coated zircalloy cladding for design-basis-accidents and beyond DBAs

Energy Technology Data Exchange (ETDEWEB)

Chun, Ji-Han, E-mail: chunjh@kaeri.re.kr; Lim, Sung-Won; Chung, Bub-Dong; Lee, Won-Jae

2015-08-15

Highlights: • Thermal conductivity model of the FCM fuel was developed and adopted in the MARS. • Scoping analysis for candidate FCM FAs was performed to select feasible FA. • Preliminary safety criteria for FCM fuel and SiC/Zr cladding were set up. • Enhanced safety margin and accident tolerance for FCM-SiC/Zr core were demonstrated. - Abstract: The FCM fueled cores proposed as an accident tolerant concept is assessed against the design-basis-accident (DBA) and the beyond-DBA (BDBA) scenarios using MARS code. A thermal conductivity model of FCM fuel is incorporated in the MARS code to take into account the effects of irradiation and temperature that was recently measured by ORNL. Preliminary analyses regarding the initial stored energy and accident tolerant performance were carried out for the scoping of various cladding material candidates. A 16 × 16 FA with SiC-coated Zircalloy cladding was selected as the feasible conceptual design through a preliminary scoping analysis. For a selected design, safety analyses for DBA and BDBA scenarios were performed to demonstrate the accident tolerance of the FCM fueled core. A loss of flow accident (LOFA) scenario was selected for a departure-from-nucleate-boiling (DNB) evaluation, and large-break loss of coolant accident (LBLOCA) scenario for peak cladding temperature (PCT) margin evaluation. A control element assembly (CEA) ejection accident scenario was selected for peak fuel enthalpy and temperature. Moreover, a station blackout (SBO) and LBLOCA without a safety injection (SI) scenario were selected as a BDBA. It was demonstrated that the DBA safety margin of the FCM core is satisfied and the time for operator actions for BDBA s is evaluated.

Structural assessment of TAPS core shroud under accident loads

International Nuclear Information System (INIS)

Bhasin, Vivek; Kushwaha, H.S.; Mahajan, S.C.; Kakodkar, A.

1996-09-01

Over the last few years, the Core Shroud of Boiling Water Reactors (BWRs) operating in foreign countries, have developed cracks at weld locations. As a first step for assessment of structural safety of Tarapur Atomic Power Station (TAPS) core shroud, its detailed stress analysis was done for postulated accident loads. This report is concerned with structural assessment of core shroud, of BWR at TAPS, subjected to loads resulting from main steam line break (MSLB), recirculation line break (RLB) and safe shut down earthquake. The stress analysis was done for core shroud in healthy condition and without any crack since, visual examination conducted till now, do not indicate presence of any flaw. Dynamic structural analysis for MSLB and RLB events was done using dynamic load factor (DLF) method. The complete core shroud and its associated components were modelled and analysed using 3D plate/shell elements. Since, the components of core shroud are submerged in water, hence, hydrodynamic added mass was also considered for evaluation of natural frequencies. It was concluded that from structural point of view, adequate safety margin is available under all the accident loads. Nonlinear analysis was done to evaluate buckling/collapse load. The collapse/buckling load have sufficient margin against the allowable limits. The displacements are low hence, the insertion of control rod may not be affected. (author)

Shock loading of reactor vessel following hypothetical core disruptive accident

International Nuclear Information System (INIS)

Srinivas, G.; Doshi, J.B.

1990-01-01

Hypothetical Core Disruptive Accident (HCDA) has been historically considered as the maximum credible accident in Fast Breeder Reactor systems. Environmental consequences of such an accident depends to a great extent on the ability of the reactor vessel to maintain integrity during the shock loading following an HCDA. In the present paper, a computational model of the reactor core and the surrounding coolant with a free surface is numerical technique. The equations for conservation of mass, momentum and energy along with an equation of state are considered in two dimensional cylindrical geometry. The reactor core at the end of HCDA is taken as a bubble of hot, vaporized fuel at high temperature and pressure, formed at the center of the reactor vessel and expanding against the surrounding liquid sodium coolant. The free surface of sodium at the top of the vessel and the movement of the core bubble-liquid coolant interface are tracked by Marker and Cell (MAC) procedure. The results are obtained for the transient pressure at the vessel wall and also for the loading on the roof plug by the impact of the slug of liquid sodium. The computer code developed is validated against a benchmark experiment chosen to be ISPRA experiment reported in literature. The computer code is next applied to predict the loading on the Indian Prototype Fast Breeder Reactor (PFBR) being developed at Kalpakkam

Mutational meltdown in laboratory yeast populations

NARCIS (Netherlands)

Zeyl, C.; Mizesko, M.; Visser, de J.A.G.M.

2001-01-01

In small or repeatedly bottlenecked populations, mutations are expected to accumulate by genetic drift, causing fitness declines. In mutational meltdown models, such fitness declines further reduce population size, thus accelerating additional mutation accumulation and leading to extinction. Because

Analysis of space-time core dynamics on reactor accident at Chernobyl

International Nuclear Information System (INIS)

Takano, Makoto; Shindo, Ryuichi; Yamashita, Kiyonobu; Sawa, Kazuhiro

1987-05-01

Regarding reactor accident at Chernobyl in USSR, core dynamics has been analyzed by COMIC code which solves space-time dependent diffusion equation in three-dimension taking spatial thermohydraulic effect into account. The code was originally developed for high temperature gas-cooled reactors (HTGR), however, has been modified to include light water as coolant, instead of helium, for analysis of the accident. In the analysis, emphasis is placed on spatial effects on core dynamics. The analyses are performed for the cases of modeling the core fully and partially where 6 fuel channels surround one control rod channel. The result shows that the speed of applying void reactivity averaged over the core depends on the power and coolant flow distributions. Therefore, these distributions have potential to influence on the value and the time of peak power estimated by calculation. (author)

European community light water reactor safety research projects. Experimental issue

International Nuclear Information System (INIS)

1975-01-01

Research programs on light water reactor safety currently carried out in the European Community are presented. They cover: accident conditions (LOCA, ECCS, core meltdown, external influences, etc...), fault and accident prevention and means of mitigation, normal operation conditions, on and off site implications and equipment under severe accident conditions, and miscellaneous subjects

GLOBAL ECONOMIC MELTDOWN AND THE NIGERIAN ...

African Journals Online (AJOL)

global financial meltdown, marked by the collapse of hitherto revered and great financial ... Indeed it is an integral part of a market (capitalist) economy. .... competitively in economic production, so also is the deficit in its trade with the rest of the.

Core-melting accidents in Chernobyl and Harrisburg

International Nuclear Information System (INIS)

Loon, A.J. van; Vonderen, A.C.M. van

1987-01-01

This publication deals with the essences of the reactor accident in Chernobylsk and the conclusions to be drawn from these with regard to reactor safety. Therein the technical differences between the reactor types in the West and the East play an important role. Also attention is spent to the now generally accepted philosophy that by simplification and making use of proven technologies, a further deminishing of the risks can be achieved step by step. In ch.'s 2 and 4 the origin and course of the accidents in respectively Chernobylsk and Harrisburg are analyzed; in the analysis of the Chernobylsk accident also date have been used which were provided by the Sovjet-Union, supplied with results of studies of the U.S. Department of Energy (DOE). In ch. 3 this information is compared with the insights which have grown at KEMA about these on the base of reactor physical and thermohydraulic considerations and of computer calculations reproducing the course of the accident. An important question is if, and if so: to which extent, an accident such as the one in Chernobylsk also can take place in the West. In order to answer that question as accurate as possible the consequences of core meltings accidents and the risk for such an accident taking place are pursued. In ch. 6 the legal frameworks are indicated by which the risk may be limited and by which eventually yet occurring damage may be arranged. Ch. 7 finally deals with the lessons which the accidents in Chernobylsk and Harrisburg have learnt us and with the possible consequences of these for the further application of nuclear power in the Netherlands. (H.W.). 105 refs.; 42 figs.; 17 refs

Containment loading during severe core damage accidents

International Nuclear Information System (INIS)

Fermandjian, J.; Evrard, J.M.; Cenerino, C.; Berthion, Y.; Carvallo, G.

1984-11-01

The objective of the article is to study the influence of the state of the reactor cavity (dry or flooded) and of the corium coolability on the thermal-hydraulics in the containment in the case of an accident sequence involving core melting and subsequent containment basemat erosion, in a 900 MWe PWR unit. Calculations are performed by using the JERICHO thermal hydraulics code

Simulation of LOF accidents with directly electrical heated UO2 pins

International Nuclear Information System (INIS)

Alexas, A.

1976-01-01

The behavior of directly electrical heated UO 2 pins has been investigated under loss of coolant conditions. Two types of hypothetical accidents have been simulated, first, a LOF accident without power excursion (LOF accident) and second, a LOF accident with subsequent power excursion (LOF-TOP accident). A high-speed film shows the sequence of events for two characteristic experiments. In consequence of the high-speed film analysis as well as the metallographical evaluation statements are given in respect to the cladding meltdown process, the fuel melt fraction and the energy input from the beginning of a power transient to the beginning of the molten fuel ejections

National radiological emergency response to the Fukushima Daiichi Nuclear Power Plant accident

International Nuclear Information System (INIS)

Dela Rosa, Alumanda M.

2011-01-01

The Fukushima nuclear power plant accident occurred on March 11, 2011, when two natural disasters of unprecedented strengths, an earthquake with magnitude 9 followed one hour later by a powerful tsunami struck northeastern Japan and felled the external power supply and the emergency diesel generators of the Fukushima Daiichi nuclear power station, resulting in a loss of coolant accident. There were core meltdowns in three nuclear reactors with the release of radioactivity estimated to be 1/10 of what was released to the environment during the Chernobyl nuclear power plant accident in April 1986. The Fukushima nuclear accident tested the capability of the Philippine Nuclear Research Institute (PNRI) and the National Disaster Risk Reduction and Management Council (NDRRMC) in responding to such radiological emergency as a nuclear power plant accident. The PNRI and NDRRMC activated the RADPLAN for possible radiological emergency. The emergency response was calibrated to the status of the nuclear reactors on site and the environmental monitoring undertaken around the site and off-site, including the marine environment. This orchestrated effort enabled the PNRI and the national agencies concerned to reassure the public that the nuclear accident does not have a significant impact on the Philippines, both on the health and safety of the people and on the safety of the environment. National actions taken during the accident will be presented. The role played by the International Atomic Energy Agency as the central UN agency for nuclear matters will be discussed. (author)

Examination of offsite emergency protective measures for core melt accidents

International Nuclear Information System (INIS)

Aldrich, D.C.; McGrath, P.E.; Ericson, D.M. Jr.; Jones, R.B.; Rasmussen, N.C.

Evacuation, sheltering followed by population relocation, and iodine prophylaxis are evaluated as offsite public protective measures in response to potential nuclear reactor accidents involving core-melt. Evaluations were conducted using a modified version of the Reactor Safety Study consequence model. Models representing each protective measure were developed and are discussed. Potential PWR core-melt radioactive material releases are separated into two categories, ''Melt-through'' and ''Atmospheric,'' based upon the mode of containment falure. Protective measures are examined and compared for each category in terms of projected doses to the whole body and thyroid. Measures for ''Atmospheric'' accidents are also examined in terms of their influence on the occurrence of public health effects

Exorcising the nightmare of reactor meltdowns. First of four articles

International Nuclear Information System (INIS)

Faltermayer, E.

1979-01-01

Facts on the hazards of reactors are investigated in this first article of four on that subject. Some knowledgeable critics warn that a serious nuclear disaster is a real possibility within the next few decades. Other experts, mostly in the nuclear industry, counter that fission power is just another engineering challenge that has been met by a society that copes with many others. Each year, they note, U.S. industry handles enough chlorine to kill the entire human race 100,000 times over. U.S. utilities have accumulated 440 reactor-years of experience with nonbreeeding reactors with no meltdowns. Beginning in 1972, a study (eventually report WASH-1400) was made of hundreds of sequences of things that could go wrong in commercial reactors, including human error, and estimated the amounts of radioactivity that could be released in each sequence under varying weather conditions; the optimistic analyses in that report are well known. In January 1979, the Nuclear Regulatory Commission issued a statement saying that it does not regard as reliable WASH-1400's figures on the overall risk of reactor accidents. In March 1975, some 1,600 electrical cables were burned in a seven-hour fire at Brown's Ferry nuclear plant near Athens, Alabama with no major accident occurring. .The LOFT reactor experiment in Idaho is described. Pipe cracks are the most worrisome problem, but these get discovered and corrected before an accident occurs. In a society that long ago lost its technological innocence, and that lives with far greater hazards both natural and manmade, nuclear power causes more unease that it should

Development of a DNBR evaluation method for the CEA ejection accident in SMART core

Energy Technology Data Exchange (ETDEWEB)

Hwang, Dae Hyun; Yoo, Y. J.; In, W. K.; Chang, M. H. [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-12-01

A methodology applicable to the analysis of the CEA ejection accident in SMART is developed for the evaluation of the fraction of fuel failure caused by DNB. The transient behavior of the core thermal-hydraulic conditions is calculated by the subchannel analysis code MATRA. The minimum DNBR during the accident is calculated by KRB-1 CHF correlation considering the 1/8 symmetry of hot assembly. The variation of hot assembly power during the accident is simulated by the LTC(Limiting transient Curve) which is determined from the analysis of power distribution data resulting from the three-dimensional core dynamics calculations. The initial condition of the accident is determined by considering LOC(Limiting Conditions for Operation) of SMART core. Two different methodologies for the evaluation of DNB failure rate are established; a deterministic method based on the DNB envelope, and a probabilistic method based on the DNB probability of each fuel rod. The methodology developed in this study is applied to the analysis of CEA ejection accident in the preliminary design core of SMART. As the result, the fractions of DNB fuel failure by the deterministic method and the probabilistic method are calculated as 38.7% and 7.8%, respectively. 16 refs., 16 figs., 5 tabs. (Author)

Discussion of the H2 problem connected with possible measures to be taken to reduce the consequences of accidents

International Nuclear Information System (INIS)

Jahn, H.

1983-01-01

The German Reactor Safety Commission's guidelines provide for the design of emergency cooling systems that no more than 1% of the zirconium materials are to react with water in a loss-of-coolant incident. If this emergency cooling marginal value is also applied as the maximum value for hydrogen control, such design-related incidents will be technically controllable concerning hydrogen (flow mixing and recombination). This report dealt exclusively with questions arising from temporary excess core temperatures owing to emergency cooling that does not meet the requirements of design and causing substantial zirconium reactions with temporary excess hydrogen generation. In order to distinguish this type of incident from unproblematic design-related incidents for one thing and from cases with complete core meltdown for another thing, the term ''accident'' is applied. (orig./RW) [de

Reference accident (Core disruption accident - safety analysis detailed report no. 11)

Energy Technology Data Exchange (ETDEWEB)

1988-01-15

The PEC safety analysis led to the conclusion that all credible sequences (incident sequences characterized by a frequency of occurrence above 10/sup minus 7/ events per year) are limited to the design basis conditions of components of the plant protection systems, and that none of them leads to a release of mechanical energy or to an extensive damage of the core and primary containment structures event in the case of failure to scram. Nevertheless, as is done in other countries for similar reactors, some events beyond the limits of credibility were considered for the PEC reactor. These were defined on a absolutely hypothetical basis that involves severe core disruption and dynamic loading of primary containment boundary. A series of containments, each having a different role, was designed to mitigate the radiological effects of a postulated core disruptive accident. The final aim was to demonstrate that residual heat can be removed and that the release of radioactivity to the environment is within acceptable limits.

Nuclear Power Reactor Core Melt Accidents. Current State of Knowledge

International Nuclear Information System (INIS)

Bentaib, Ahmed; Bonneville, Herve; Clement, Bernard; Cranga, Michel; Fichot, Florian; Koundy, Vincent; Meignen, Renaud; Corenwinder, Francois; Leteinturier, Denis; Monroig, Frederique; Nahas, Georges; Pichereau, Frederique; Van-Dorsselaere, Jean-Pierre; Cenerino, Gerard; Jacquemain, Didier; Raimond, Emmanuel; Ducros, Gerard; Journeau, Christophe; Magallon, Daniel; Seiler, Jean-Marie; Tourniaire, Bruno

2013-01-01

For over thirty years, IPSN and subsequently IRSN has played a major international role in the field of nuclear power reactor core melt accidents through the undertaking of important experimental programmes (the most significant being the Phebus- FP programme), the development of validated simulation tools (the ASTEC code that is today the leading European tool for modelling severe accidents), and the coordination of the SARNET (Severe Accident Research Network) international network of excellence. These accidents are described as 'severe accidents' because they can lead to radioactive releases outside the plant concerned, with serious consequences for the general public and for the environment. This book compiles the sum of the knowledge acquired on this subject and summarises the lessons that have been learnt from severe accidents around the world for the prevention and reduction of the consequences of such accidents, without addressing those from the Fukushima accident, where knowledge of events is still evolving. The knowledge accumulated by the Institute on these subjects enabled it to play an active role in informing public authorities, the media and the public when this accident occurred, and continues to do so to this day

Thermal and hydraulic behaviour of CANDU cores under severe accident conditions - final report. Vol. 1

International Nuclear Information System (INIS)

Rogers, J.T.

1984-06-01

This report gives the results of a study of the thermo-hydraulic aspects of severe accident sequences in CANDU reactors. The accident sequences considered are the loss of the moderator cooling system and the loss of the moderator heat sink, each following a large loss-of-coolant accident accompanied by loss of emergency coolant injection. Factors considered include expulsion and boil-off of the moderator, uncovery, overheating and disintegration of the fuel channels, quenching of channel debris, re-heating of channel debris following complete moderator expulsion, formation and possible boiling of a molten pool of core debris and the effectiveness of the cooling of the calandria wall by the shield tank water during the accident sequences. The effects of these accident sequences on the reactor containment are also considered. Results show that there would be no gross melting of fuel during moderator expulsion from the calandria, and for a considerable time thereafter, as quenched core debris re-heats. Core melting would not begin until about 135 minutes after accident initiation in a loss of the moderator cooling system and until about 30 minutes in a loss of the moderator heat sink. Eventually, a pool of molten material would form in the bottom of the calandria, which may or may not boil, depending on property values. In all cases, the molten core would be contained within the calandria, as long as the shield tank water cooling system remains operational. Finally, in the period from 8 to 50 hours after the initiation of the accident, the molten core would re-solidify within the calandria. There would be no consequent damage to containment resulting from these accident sequences, nor would there be a significant increase in fission product releases from containment above those that would otherwise occur in a dual failure LOCA plus LOECI

Zircaloy-oxidation and hydrogen-generation rates in degraded-core accident situations

International Nuclear Information System (INIS)

Chung, H.M.; Thomas, G.R.

1983-02-01

Oxidation of Zircaloy cladding is the primary source of hydrogen generated during a degraded-core accident. In this paper, reported Zircaloy oxidation rates, either measured at 1500 to 1850 0 C or extrapolated from the low-temperature data obtained at 0 C, are critically reviewed with respect to their applicability to a degraded-core accident situation in which the high-temperature fuel cladding is likely to be exposed to and oxidized in mixtures of hydrogen and depleted steam, rather than in an unlimited flux of pure steam. New results of Zircaloy oxidation measurements in various mixtures of hydrogen and steam are reported for >1500 0 C. The results show significantly smaller oxidation and, hence, hydrogen-generation rates in the mixture, compared with those obtained in pure steam. It is also shown that a significant fraction of hydrogen, generated as a result of Zircaloy oxidation, is dissolved in the cladding material itself, which prevents that portion of hydrogen from reaching the containment building space. Implications of these findings are discussed in relation to a more realistic method of quantifying the hydrogen source term for a degraded-core accident analysis

Core damage frequency estimation using accident sequence precursor data: 1990-1993

International Nuclear Information System (INIS)

Martz, H.F.

1998-01-01

The Nuclear Regulatory Commission's (NRC's) ongoing Accident Sequence Precursor (ASP) program uses probabilistic risk assessment (PRA) techniques to assess the potential for severe core damage (henceforth referred to simply as core damage) based on operating events. The types of operating events considered include accident sequence initiators, safety equipment failures, and degradation of plant conditions that could increase the probability that various postulated accident sequences occur. Such operating events potentially reduce the margin of safety available for prevention of core damage an thus can be considered as precursors to core damage. The current process for identifying, analyzing, and documenting ASP events is described in detail in Vanden Heuval et al. The significance of a Licensee Event Report (LER) event (or events) is measured by means of the conditional probability that the event leads to core damage, the so-called conditional core damage probability or, simply, CCDP. When the first ASP study results were published in 1982, it covered the period 1969--1979. In addition to identification and ranking of precursors, the original study attempted to estimate core damage frequency (CDF) based on the precursor events. The purpose of this paper is to compare the average annual CDF estimates calculated using the CCDP sum, Cooke-Goossens, Bier, and Abramson estimators for various reactor classes using the combined ASP data for the four years, 1990--1993. An important outcome of this comparison is an answer to the persistent question regarding the degree and effect of the positive bias of the CCDP sum method in practice. Note that this paper only compares the estimators with each other. Because the true average CDF is unknown, the estimation error is also unknown. Therefore, any observations or characterizations of bias are based on purely theoretical considerations

Radioactivity inspection of Taiwan for food products imported from Japan after the Fukushima nuclear accident

International Nuclear Information System (INIS)

Chiu, Huang-Sheng; Huang, Ping-Ji; Wuu, Jyi-Lan; Wang, Jeng-Jong

2013-01-01

The 3–11 Earthquake occurred in Japan last year had greatly damaged the lives and properties and also caused the core meltdown accident in the Fukushima nuclear power plant followed by the leakage of radioactive materials into biosphere. In order to protect against the detriment of radiation from foods which were imported from Japan, the Institute of Nuclear Energy Research (INER) in Taiwan started to conduct radioactivity inspection of food products from Japan after the accident. A total of about 20,000 samples had been tested from March 24 2011 to March 31 2012. - Highlights: • About 20,000 food products imported from Japan were tested by low-background HPGe detectors. • In total, 46 food products had been found to be contaminated by I-131, Cs-134 or Cs-137, however, the radiation levels were all below the limit of Taiwanese regulations. • The measurement techniques described in this study can be used as a fast screening tool to ensure safety of food supplied

Current position on severe accident phenomena

Energy Technology Data Exchange (ETDEWEB)

Henry, Robert E [Fauske and Associates, Inc., Burr Ridge, IL (United States)

2004-07-01

The phenomena addressed in this lecture are: in-vessel and ex-vessel hydrogen generation; in-vessel and in-containment natural circulation, steam explosions, direct containment heating, core-concrete interaction; debris coolability, containment strength/failure. The following events were modeled: axial and radial power distribution, two-phase level in the core, steam generation in covered section, decay heat generation, convection to gas, cladding oxidation, cold ballooning and rupture, natural circulation between the core and upper plenum, hydrogen generation, core meltdown, reflooding. Differences between PWR and BWR type reactors.

Current position on severe accident phenomena

International Nuclear Information System (INIS)

Henry, Robert E.

2004-01-01

The phenomena addressed in this lecture are: in-vessel and ex-vessel hydrogen generation; in-vessel and in-containment natural circulation, steam explosions, direct containment heating, core-concrete interaction; debris coolability, containment strength/failure. The following events were modeled: axial and radial power distribution, two-phase level in the core, steam generation in covered section, decay heat generation, convection to gas, cladding oxidation, cold ballooning and rupture, natural circulation between the core and upper plenum, hydrogen generation, core meltdown, reflooding. Differences between PWR and BWR type reactors

Behaviour of LWR core materials under accident conditions. Proceedings of a technical committee meeting

International Nuclear Information System (INIS)

1996-12-01

At the invitation of the Government of the Russian Federation, following a proposal of the International Working Group on Water Reactor Fuel Performance and Technology, the IAEA convened a Technical Committee Meeting on Behaviour of LWR Core Materials Under Accident Conditions from 9 to 13 October 1995 in Dimitrovgrad to analyze and evaluate the behaviour of LWR core materials under accident conditions with special emphasis on severe accidents. In-vessel severe accidents phenomena were considered in detail, but specialized thermal hydraulic aspects as well as ex-vessel phenomena were outside the scope of the meeting. Forty participants representing eight countries attended the meeting. Twenty-three papers were presented and discussed during five sessions. Refs, figs, tabs

Normal accidents living with high-risk technologies

CERN Document Server

Perrow, Charles

1984-01-01

Normal Accidents analyzes the social side of technological risk. Charles Perrow argues that the conventional engineering approach to ensuring safety--building in more warnings and safeguards--fails because systems complexity makes failures inevitable. He asserts that typical precautions, by adding to complexity, may help create new categories of accidents. (At Chernobyl, tests of a new safety system helped produce the meltdown and subsequent fire.) By recognizing two dimensions of risk--complex versus linear interactions, and tight versus loose coupling--this book provides a powerful framework for analyzing risks and the organizations that insist we run them.

Main results of German risk study, Phase B, in the light of methodological problems

International Nuclear Information System (INIS)

Koeberlein, K.

1991-01-01

The German Risk Study, Phase B, which has been performed for a 1,300 MWe KWU-type pressurized water reactor, is a level 2 probabilistic safety assessment (PSA). In the study, 32 initiating events have been considered. An expected plant damage state frequency of about 3x10 -5 per year has been calculated. In a plant damage state core meltdown can only be prevented by means of accident management procedures. The probability is high (about 98%) that in a plant damage state the primary system will not be depressurized. Core meltdown under high system pressure would endanger the containment integrity immediately. In most plant damage states accident management procedures are possible which bring the plant in a safe state or, at least, reduce the pressure in the primary system before the pressure vessel fails. On a preliminary basis, a success probability of 99% for accident management procedures (secondary or primary side bleed and feed) has been estimated. This results in an expected core melt frequency of about 4x10 -6 per year. The expected frequency of high pressure core meltdown is about 6x10 -7 per year. Loads on, and failure modes of, the containment during a core melt accident as well as release fractions after containment failure have been analyzed. The study did, however, refrain from quantifying the probability of containment failure modes. A main uncertainty in this area is the probability of containment failure due to hydrogen burning. The results of the study point out, that the risk can be reduced significantly if containment failure due to hydrogen burning can be reliably prevented

Method for consequence calculations for servere accidents

International Nuclear Information System (INIS)

Nielsen, F.

1987-01-01

With the exception of the part about collective doses, this report was commissioned by the Swedish State Power Board. The part about collective doses was commissioned by the Swedish National Institute of Radiation Protection. The report contains a calculation of radiation doses in the sursurroundings caused by a theoretical core meltdown accident at one of the Barsebaeck reactors with filtered venting through the FILTRA plant. The calculations were made by means of the PLUCON4 code. The assumption used for the calculations were givon by the Swedish National Institute of Radiation Protection as follows: Pasquill D with wind speed 3 m/s and a mixing layer at 300 m height. Elevation of the release: 100 m with no energy release. The release starts 12 hours after shut-down and its duration is one hour. The release contains 100% of the noble gasses and 0,1% of all other isotopes in a 1800 MW t -reactor. (author)

Considerations on the influence of fission products in whole core accidents

International Nuclear Information System (INIS)

Meyer Heine, A.; Pattoret, A.; Schmitz, F.

1977-01-01

If the hypothetical Whole Core Accidents which are taken into account in reactor safety analysis can change from one country to another, there is nevertheless a general agreement over their description and main phases. Furthermore the important parameters have also been identified by every laboratory. During the development of such core accidents the role of the fission products in essential. It is not the purpose of this paper to give an exhaustive description of the phases which can be influenced by the fission products, we will try however to focus this study on the most important ones. In a second step we will discuss the equation of state of irradiated fuels; here again one principal preoccupation being to quantify the influence of fission products on reactor accidents. It is not our purpose to enter on the fundamental aspects of the equation of state. The studies and the experimental program launched at the CEA will then be described. Special attention will be directed towards the eventual role of fission products in molten fuel-coolant interactions (MFCls) or the events leading to the initiation of whole core accidents. This paper will be limited to oxide fuels. Whether the whole core accident is initiated by a reactivity defect or a coolant coast-down, one has to deal with four great categories of phenomena. Loss of flow: the power is around the nominal value, while the coolant flow has been reduced by a factor of 5 to 10. This induces boiling and clad weakening. Will the plenum pressure lead to a clad rupture? In case of a rupture, what will be the effect on the voiding of the channel? Transient over power: influence of gases from gaseous and volatile fission products on the fuel movements? MFCIs: Influence of the fission products in the mode of contact between fuel and coolant? Influence on the fuel characteristics. Sodium vapour bubble expansion: influence of the fission products on the heat transfer and eventual condensation of the bubble?

Re-assessment of road accident data-analysis policy : applying theory from involuntary, high-consequence, low-probability events like nuclear power plant meltdowns to voluntary, low-consequence, high-probability events like traffic accidents

Science.gov (United States)

2002-02-01

This report examines the literature on involuntary, high-consequence, low-probability (IHL) events like nuclear power plant meltdowns to determine what can be applied to the problem of voluntary, low-consequence high-probability (VLH) events like tra...

Poison and diluent system for nuclear power plants

International Nuclear Information System (INIS)

Parker, W.G.; Ravets, J.M.; Preble, B.S.

1978-01-01

A system to prevent supercriticality in nuclear power plants in the unlikely event of a core destructive accident terminating in the nuclear core meltdown is described. The system dilutes and poisons the molten core to maintain subcriticality, and is useful in mobile nuclear power plants, or in nuclear plants subject to seismic disturbances, where the orientation of the nuclear reactor after the accident is unknown. It is also applicable to alleviate the consequences of loss of coolant flow accidents from any cause. Aside from preventing supercriticality, the system serves the dual purpose of acting as a biological shield and/or structural member that reduces the deleterious effects of accidental core impaction, without compromising power plant weight and size constraints. A borated material, with a melting point greater than the fuel melting point, is inserted in the pressure vessel behind an inner wall. In the unlikely event of a core meltdown, the molten fuel melts through the inner wall and is diluted and poisoned by the borated material. In the event the molten fuel melts through the pressure vessel, additional borated material is provided to continue diluting and poisoning

Modeling of BWR core meltdown accidents - for application in the MELRPI. MOD2 computer code

Energy Technology Data Exchange (ETDEWEB)

Koh, B R; Kim, S H; Taleyarkhan, R P; Podowski, M Z; Lahey, Jr, R T

1985-04-01

This report summarizes improvements and modifications made in the MELRPI computer code. A major difference between this new, updated version of the code, called MELRPI.MOD2, and the one reported previously, concerns the inclusion of a model for the BWR emergency core cooling systems (ECCS). This model and its computer implementation, the ECCRPI subroutine, account for various emergency injection modes, for both intact and rubblized geometries. Other changes to MELRPI deal with an improved model for canister wall oxidation, rubble bed modeling, and numerical integration of system equations. A complete documentation of the entire MELRPI.MOD2 code is also given, including an input guide, list of subroutines, sample input/output and program listing.

Water reactor fuel behaviour and fission products release in off-normal and accident conditions

International Nuclear Information System (INIS)

1987-09-01

The present meeting was scheduled by the International Atomic Energy Agency upon the proposal of the Members of the International Working Group on Water Reactor Fuel Performance and Technology and held at the IAEA Headquarters in Vienna from 10 to 13 November 1986. Thirty participants from 17 countries and an international organization attended the meeting. Eighteen papers were presented from 13 countries and one international organization. The meeting was composed of four sessions and covered subjects related to: physico-chemical properties of core materials under off-normal conditions, and their interactions up to and after melt-down (5 papers); core materials deformation, relocation and core coolability under (severe) accident conditions (4 papers); fission products release: including experience, mechanisms and modelling (5 papers); power plant experience (4 papers). A separate abstract was prepared for each of these 18 papers. Four working groups covering the above-mentioned topics were held to discuss the present status of the knowledge and to develop recommendations for future activities in this field. Refs, figs and tabs

Safety analysis of RA reactor operation, I-III, Part III - Environmental effect of the maximum credible accident

International Nuclear Information System (INIS)

Raisic, N.

1963-02-01

Maximum credible accident at the RA reactor would consider release of fission products into the environment. This would result from fuel elements failure or meltdown due to loss of coolant. The analysis presented in this report assumes that the reactor was operating at nominal power at the moment of maximum possible accident. The report includes calculations of fission products activity at the moment of accident, total activity release during the accident, concentration of radioactive material in the air in the reactor neighbourhood, and the analysis of accident environmental effects

Phenomena occurring in the reactor coolant system during severe core damage accidents

International Nuclear Information System (INIS)

Malinauskas, A.P.

1989-01-01

The reactor coolant system (RCS) of a nuclear power plant consists of the reactor pressure vessel and the piping and associated components that are required for the continuous circulation of the coolant which is used to maintain thermal equilibrium throughout the system. In the event of an accident, the RCS also serves as one of several barriers to the escape of radiotoxic material into the biosphere. In contrast to normal operating conditions, severe core damage accidents are characterized by significant temporal and spatial variations in heat and mass fluxes, and by eventual geometrical changes within the RCS. Furthermore, the difficulties in describing the system in the severe accident mode are compounded by the occurrence of chemical reactions. These reactions can influence both the thermal and the mass transport behavior of the system. In addition, behavior of the reactor vessel internals and of materials released from the core region (especially the radioactive fission products) in the course of the accident likewise become of concern to the analyst. This report addresses these concerns. 9 refs., 1 tab

Consideration of BORAX-type reactivity accidents applied to research reactors

International Nuclear Information System (INIS)

Couturier, Jean; Meignen, Renaud; Bourgois, Thierry; Biaut, Guillaume; Mireau, Jean-Pierre; Natta, Marc

2011-01-01

Most of the research reactors discussed in this document are pool-type reactors in which the reactor vessel and some of the reactor coolant systems are located in a pool of water. These reactors generally use fuel in plate assemblies formed by a compact layer of uranium (or U 3 Si 2 ) and aluminium particles, sandwiched between two thin layers of aluminium serving as cladding. The fuel melting process begins at 660 deg. C when the aluminium melts, while the uranium (or U 3 Si 2 ) particles may remain solid. The accident that occurred in the American SL-1 reactor in 1961, together with tests carried out in the United States as of 1954 in the BORAX-1 reactor and then, in 1962, in the SPERT-1 reactor, showed that a sudden substantial addition of reactivity in this type of reactor could lead to explosive mechanisms caused by degradation, or even fast meltdown, of part of the reactor core. This is what is known as a 'BORAX-type' accident. The aim of this document is first to briefly recall the circumstances of the SL-1 reactor accident, the lessons learned, how this operational feedback has been factored into the design of various research reactors around the world and, second, to describe the approach taken by France with regard to this type of accident and how, led by IRSN, this approach has evolved in the last decade. (authors)

Accident risk. Chapter 5

International Nuclear Information System (INIS)

1978-01-01

Following a historical introduction in which WASH-740, WASH-1400, Swedish, Finnish, Scandinavian, Netherlands and West German analyses are briefly presented, the concept of risk itself is discussed, distinguishing between objective and subjective aspects, and between voluntary and involuntary risk. Risk analysis is briefly described and an attempt made to define acceptable risk. In treating the safety philosophy of nuclear power plants the engineered safety precautions are presented. The numerical results of the analysis made for Norwegian conditions are presented and discussed. Underground siting, which has been much discussed in Norway is also treated, and emergency planning briefly discussed. The probability and consequences of core meltdown in a light water reactor are then discussed, and the possible faults leading to this, both internal, human errors and external impacts are analysed. The failure mechanisms in the containment building which could lead to the release of activity are discussed, followed by the dispersion of the activity and the health and economic consequences. The accidents at Wuergassen and Brown's Ferry are briefly described as examples. A brief discussion of nuclear insurance and nuclear law in Norway form the concluding sections. (JIW)

the accident at Three Mile Island

International Nuclear Information System (INIS)

Torrey, L.

1979-01-01

The recently published final report of the President's Commision on the accident at Three Mile Island (TMI) is considered. In the report the power utilities and the US Nuclear Regulatory Commission (NRC) are severely criticised for being 'unable to provide an acceptable level of safety in nuclear power' which is reflected in the operators lack of training and understanding in depth. The 44 recommendations of the Commission include the abolition of the NRC, periodic renewal of operating licences, the siting of all future nuclear power plants away from large population centres, emergency response procedures to be improved and the revamping of warning display panels in control rooms. The commission also evaluated the severity of the accident and endeavoured to determine how close TMI came to a total catastrophic meltdown. The role of the media in the accident was also considered. (UK)

Analysis of hypothetical LMFBR whole-core accidents in the USA

International Nuclear Information System (INIS)

Ferguson, D.R.; Deitrich, L.W.; Brown, N.W.; Waltar, A.E.

1978-01-01

The issue of hypothetical whole-core accidents continues to play a significant role in assessment of the potential risk to the public associated with LMFBR operation in the USA. The paper briefly characterizes the changing nature of this role, with emphasis on the current risk-oriented perspective. It then describes the models and codes used for accident analysis in the USA which have been developed under DOE sponsorship and summarizes some specific applications of the codes to the current generation of fast reactors. An assessment of future trends in this area concludes the paper

Dose estimation for nuclear power plant 4 accident in Taiwan at Fukushima nuclear meltdown emission level.

Science.gov (United States)

Tang, Mei-Ling; Tsuang, Ben-Jei; Kuo, Pei-Hsuan

2016-05-01

An advanced Gaussian trajectory dispersion model is used to evaluate the evacuation zone due to a nuclear meltdown at the Nuclear Power Plant 4 (NPP4) in Taiwan, with the same emission level as that occurred at Fukushima nuclear meltdown (FNM) in 2011. Our study demonstrates that a FNM emission level would pollute 9% of the island's land area with annual effective dose ≥50 mSv using the meteorological data on 11 March 2011 in Taiwan. This high dose area is also called permanent evacuation zone (denoted as PEZ). The PEZ as well as the emergency-planning zone (EPZ) are found to be sensitive to meteorological conditions on the event. In a sunny day under the dominated NE wind conditions, the EPZ can be as far as 100 km with the first 7-day dose ≥20 mSv. Three hundred sixty-five daily events using the meteorological data from 11 March 2011 to 9 March 2012 are evaluated. It is found that the mean land area of Taiwan in becoming the PEZ is 11%. Especially, the probabilities of the northern counties/cities (Keelung, New Taipei, Taipei, Taoyuan, Hsinchu City, Hsinchu County and Ilan County) to be PEZs are high, ranging from 15% in Ilan County to 51% in Keelung City. Note that the total population of the above cities/counties is as high as 10 million people. Moreover, the western valleys of the Central Mountain Range are also found to be probable being PEZs, where all of the reservoirs in western Taiwan are located. For example, the probability can be as high as 3% in the far southern-most tip of Taiwan Island in Pingtung County. This shows that the entire populations in western Taiwan can be at risk due to the shortage of clean water sources under an event at FNM emission level, especially during the NE monsoon period. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

The radiological consequences of degraded core accidents for the Sizewell PWR The impact of adopting revised frequencies of occurrence

CERN Document Server

Kelly, G N

1983-01-01

The radiological consequences of degraded core accidents postulated for the Sizewell PWR were assessed in an earlier study and the results published in NRPB-R137. Further analyses have since been made by the Central Electricity Generating Board (CEGB) of degraded core accidents which have led to a revision of their predicted frequencies of occurrence. The implications of these revised frequencies, in terms of the risk to the public from degraded core accidents, are evaluated in this report. Increases, by factors typically within the range of about 1.5 to 7, are predicted in the consequences, compared with those estimated in the earlier study. However, the predicted risk from degraded core accidents, despite these increases, remains exceedingly small.

The role of fission products in whole core accidents

Energy Technology Data Exchange (ETDEWEB)

Baker, A R [FRSD, UKAEA, RNPDE, Risley, Warrington (United Kingdom); Teague, H J [SRD, UKAEA, Culcheth, Warrington (United Kingdom)

1977-07-01

The review of the role of fission products in whole-core accidents falls into two parts. Firstly, there is a discussion of the hypothetical accidents usually considered in the UK and how they are dealt with. Secondly, there is a discussion of individual topics where fission products are known to be important or might be so. There is a brief discussion of the UK work on the establishment of an equation of state for unirradiated fuel and how this might be extended to incorporate fission product effects. The main issue is the contribution of fission products to the effective vapour pressure and the experimental programme on the pulsed reactor VIPER investigates this. Fission products may influence the probability of occurrence and the severity of MFCIs. Finally, the fission product effects in the pre-disassembly, disassembly and recriticality stages of an accident are discussed. (author)

Comparative study of heterogeneous and homogeneous LMFBR cores in some accident conditions

International Nuclear Information System (INIS)

Renard, A.; Evrard, G.

1978-01-01

An heterogeneous design and a homogeneous one of a LMFBR core with the same power and similar dimensions are compared from the safety point-of-view. The comparison is performed for several accident conditions, such as Loss-of-Flow and Transient Overpower, with the same failure criteria and model assumptions for both cores. Qualitative trends are deduced from the behaviour of the core designs in the investigated transient conditions. (author)

Spread of fission products after a nuclear melt-down accident

International Nuclear Information System (INIS)

Andriesse, C.D.; Tanke, R.H.J.

1987-01-01

In this article experimental investigation is described into the spread of fission products within a nuclear power plant, which after an accident involving melting of the nucleus, will be possible in spite of prohibiting constructions for the case of severe unbalancing of generated and carried-off energy. 6 refs.; 4 figs

Laboratory studies of the meltfront propagation in a borax core-catcher

International Nuclear Information System (INIS)

Dalle Donne, M.; Werle, H.

1980-08-01

A series of seven laboratory experiments concerning the meltdown of a borax core catcher have been performed. By the selection of the simulant materials the most important thermophysical properties of the core catcher materials were taken into account. Fission product heating of the molten core masses was simulated by electrolytically heating of the molten region. The experiments reveal interesting details of the phenomena to be expected during melt-down of a borax core catcher, especially on the flow pattern, the mixing processes of molten materials and the layer formation the melt. The most interesting result is that the ratio of downward to sideward melting rate is heavily reduced by high melting barriers and that a cubic structure of barriers will not equalize downward and sideward melting rates. A super 8 film is available as additional information. (orig.) [de

Destruction of the BETA experimental facility for core meltdown experiments in the Karlsruhe Nuclear Research Center on 21 March 1992

International Nuclear Information System (INIS)

Feige, K.D.

1992-01-01

The BETA experiment V 6.2 was intended to yield information on the processes involved in a lateral containment meltdown starting in a concrete wall with external water cooling. The unexpected overpressure that caused the explosion occurred 1896 seconds after the melt had been fed into the crucible, inducing the melt-water interaction. The explosion destroyed only the inner space of the facility. (orig.) [de

Accidents and transients analyses of a super fast reactor with single flow pass core

International Nuclear Information System (INIS)

Sutanto,; Oka, Yoshiaki

2014-01-01

Highlights: • Safety analysis of a Super FR with single flow pass core is conducted. • Loss of feed water flow leads to a direct effect on the loss of fuel channel flow. • The core pressure is sensitive to LOCA accidents due to the direct effect. • Small LOCA introduces a critical break. • The safety criteria for all selected events are satisfied. - Abstract: The supercritical water cooled fast reactor with single flow pass core has been designed to simplify refueling and the structures of upper and lower mixing plenums. To evaluate the safety performance, safety analysis has been conducted with regard to LOCA and non-LOCA accidents including transient events. Safety analysis results show that the safety criteria are satisfied for all selected events. The total loss of feed water flow is the most important accident which the maximum cladding surface temperature (MCST) is high due to a direct effect of the accident on the total loss of flow in all fuel assemblies. However, actuation of the ADS can mitigate the accident. Small LOCA also introduces a critical break at 7.8% break which results high MCST at BOC because the scram and ADS are not actuated. Early ADS actuation is effective to mitigate the accident. In large LOCA, 100% break LOCA results a high MCST of flooding phase at BOC due to high power peaking at the bottom part. Use of high injection flow rate by 2 LPCI units is effective to decrease the MCST

Analysis of Fukushima Daiichi Nuclear Power Station severe accident using MAAP4.05

International Nuclear Information System (INIS)

Yoo, Jae S.; Suh, Kune Y.; Kim, Dong M.

2011-01-01

Rather extensive reactor core meltdown and partial melt-through that took place at the Fukushima Daiichi nuclear power plants (NPPs) on March 11, 2011 had been caused by a massive earthquake followed by tsunami rarely seen in history. The happening had turned into an unprecedented serious accident since the Chernobyl Unit 4 in 1986 that extended over multiple reactors simultaneously. A previous documentary survey, NUREG-1150 report provides significant insights into how a severe accident might develop at a boiling water reactor (BWR) and the range of consequences. NUREG-1150 did identify the importance of loss of power accidents for a BWR. This paper describes recent analyses of the Fukushima Daiichi NPPs severe accident. Calculations were performed with the MAAP4.05 code by modifying the parameter file for the Peach Bottom Unit 2, a BWR 4 type in the Mark-I containment. Generally this is the same type of reactor as Fukushima Daiichi Units 2 and 3. This resulted in good understanding of the response of this type of early BWRs to prolonged loss of diesel generators and batteries. There is clearly vulnerability with this early type of BWRs which would be less onerous than later existing plant and new build designs. This analysis, however, was based on rather limited amount of information obtained at the time of preparing this report and adopted various estimates and assumptions for conditions necessary to run the analysis. Hence there persists considerable uncertainty in the results. MAAP4.05 was run pursuant to the observed data and chronology of Fukushima Daiichi Units 1 through 3 reported by the Tokyo Electric Power Company (TEPCO) as well as the Japanese Government. Severe accident scenarios have not only gone far beyond the design basis, but also exceeded the extent of multiple breakdowns assumed in the preparation for such accident management measures as the malfunction or loss of all the emergency core cooling system (ECCS) combined with the extended loss of

MORECA: A computer code for simulating modular high-temperature gas-cooled reactor core heatup accidents

International Nuclear Information System (INIS)

Ball, S.J.

1991-10-01

The design features of the modular high-temperature gas-cooled reactor (MHTGR) have the potential to make it essentially invulnerable to damage from postulated core heatup accidents. This report describes the ORNL MORECA code, which was developed for analyzing postulated long-term core heatup scenarios for which active cooling systems used to remove afterheat following the accidents can be assumed to the unavailable. Simulations of long-term loss-of-forced-convection accidents, both with and without depressurization of the primary coolant, have shown that maximum core temperatures stay below the point at which any significant fuel failures and fission product releases are expected. Sensitivity studies also have been done to determine the effects of errors in the predictions due both to uncertainties in the modeling and to the assumptions about operational parameters. MORECA models the US Department of Energy reference design of a standard MHTGR

Examination of offsite radiological emergency measures for nuclear reactor accidents involving core melt

International Nuclear Information System (INIS)

Aldrich, D.C.; McGrath, P.E.; Rasmussen, N.C.

1978-06-01

Evacuation, sheltering followed by population relocation, and iodine prophylaxis are evaluated as offsite public protective measures in response to nuclear reactor accidents involving core-melt. Evaluations were conducted using a modified version of the Reactor Safety Study consequence model. Models representing each measure were developed and are discussed. Potential PWR core-melt radioactive material releases are separated into two categories, ''Melt-through'' and ''Atmospheric,'' based upon the mode of containment failure. Protective measures are examined and compared for each category in terms of projected doses to the whole body and thyroid. Measures for ''Atmospheric'' accidents are also examined in terms of their influence on the occurrence of public health effects

Development of CHF models for inner and outer RPV gaps in a meltdown severe accident

International Nuclear Information System (INIS)

Wang, J.; Tian, W.X.; Feng, K.; Yu, H.X.; Zhang, Y.P.; Su, G.H.; Qiu, S.Z.

2013-01-01

Highlights: • A CHF model was developed to predict the CHF in hemispherical narrow gap. • The computed result was validated by the test data of Park and Köhler. • An analytical CHF model was developed to predict the CHF on the outer surface of the lower head. • The predicted CHF was compared with the experimental data of ULPU-V. • Two CHF models developed for the inner and outer CHF predict the CHF well. - Abstract: During a severe accident, the core melt relocates in the lower head and a hemispherical narrow gap may appear between the crust and the lower head because of the different material expansion ratio. The existence of this gap is very important to the integrity of the lower head. Based on the counter current flow limitation (CCFL) between the vapor phase and the liquid phase, a CHF model was developed to predict the CHF in hemispherical narrow gap. The CHF model developed was validated by the test data of Park and Köhler. The effect of key parameters, including the system pressure, radius of melt, and gap size, on the CHF were investigated. And the TMI-2 accident was also calculated by using the CHF formula. Moreover, based on the interface separation model, an analytical CHF model was developed to predict the CHF on the outer surface of the lower head. The predicted CHF was compared with the experimental data of ULPU-V. It indicated that the CHF models developed for the inner and outer CHF could predict the CHF well

Consequence analysis of core damage states following severe accidents for the CANDU reactor design

International Nuclear Information System (INIS)

Wahba, N.N.; Kim, Y.T.; Lie, S.G.

1997-01-01

The analytical methodology used to evaluate severe accident sequences is described. The relevant thermal-mechanical phenomena and the mathematical approach used in calculating the timing of the accident progression and source term estimate are summarized. The postulated sever accidents analyzed, in general, mainly differ in the timing to reach and progress through each defined c ore damage state . This paper presents the methodology and results of the timing and steam discharge calculations as well as source term estimate out of containment for accident sequences classified as potentially leading to core disassembly following a small break loss-of-coolant accident (LOCA) scenario as a specific example. (author)

APRI-7 Accident Phenomena of Risk Importance. A progress report on research in the field of severe accidents in 2009-2011

International Nuclear Information System (INIS)

Garis, Ninos; Agrell, Maria; Glaenneskog, Henrik

2012-01-01

Knowledge of the phenomena that may occur during severe accidents in a nuclear power plant is an important prerequisite for being able to predict the plant behavior, in order to formulate procedures and instructions for incident handling, for contingency planning, and to get good quality at the accident analysis and risk studies. Since the early 80's nuclear power companies and authorities in Sweden has collaborated in research on severe reactor accidents. Cooperation in the beginning was mostly linked to strengthening the protection against environmental impacts after a severe reactor accident, in particular to develop systems for filtered depressurization of the reactor containment. Since the early 90's the cooperation has partially changed and shifted to the phenomenological questions of risk dominance. During the years 2009-2011, cooperation continued in the research-program APRI-7. The aim was to show whether the solutions adopted in the Swedish strategy for accident management provides reasonable protection for the environment. This was done by gaining detailed knowledge of both important phenomena in the hearth melting behavior, and the amount of radioactivity that can be discharged to the surroundings during a severe accident. To achieve this aim, the research program has included a follow-up of international research in severe accidents and evaluation of results, and continued to support research at KTH and Chalmers Univ. of severe accidents. The follow-up of international research has promoted the exchange of knowledge and experience and has provided access to a wealth of information about various phenomena relevant to the events at severe accidents. This was important to obtain a good basis for assessment of abatement measures in the Swedish nuclear reactors. Continuing support to the Royal Inst. of Technology has provided increased knowledge about the ability to cool the molten core of the reactor vessel and the processes associated with cooling the

Summary of severe accident assessment for Atucha 2 Nuclear Power Plant using RELAP5/SCDAPSIM Mod3.6

International Nuclear Information System (INIS)

Bonelli, Analia; Mazzantini, Oscar; Siefken, Larry; Allison, Chris

2014-01-01

A severe accident assessment was performed for the Atucha 2 Nuclear Power Plant in Argentina. Atucha 2 is a PHWR, cooled and moderated by heavy water, presently in commissioning process. Its 451 fuel assemblies are 6.03m high and each composed of 37 Zircaloy clad fuel rods. Each assembly is placed inside an individual Zircaloy coolant channel. Heavy water coolant flows inside the channels which are all immersed inside the moderator tank. The RPV lower plenum is occupied by a massive steel structure called 'filling body' that was designed to minimize heavy water inventory. Due to some unique design characteristics, severe accident progression in Atucha 2 is expected to be somewhat different from that predicted for regular PWRs. Therefore, a very detailed assessment was performed, focused on the different accident stages and expected phenomena by the use of different input models and nodalizations. When possible, linking to available experimental data was performed. RELAP/SCDAPSIM Mod 3.6 was the computer code selected to perform this task. The modeling of Atucha 2's unique characteristics required several extensions to the code. For the severe accident assessment of Atucha 2, three different input models were developed that were key instruments for the debugging and evaluation process. A Single Channel Model was used to evaluate the first stages of core heatup (including the boiloff of the channels and moderator tank), an RPV standalone model was used to assess the interaction between components in the complete core and for the evaluation of late in-core melting and relocation. Then, a Lower Plenum standalone model was developed to assess the behavior of the melted and slumped core material on top of the filling body and to analyze ex-vessel cooling as a possible severe accident management action. For each of the cases, highlights of key results are shown and general conclusions are drawn. In the case of a severe accident with significant meltdown of

Fukushima nuclear accident and the social responsibility of science

International Nuclear Information System (INIS)

Yoshioka, Hitoshi

2011-01-01

Five months had passed since Fukushima Daiichi Nuclear Power Plant (NPP) accident occurred but still there was no knowing when the accident ended. Released radioactivity seemed to be greater than one million terra Bq and if there occurred an explosive rupture of containment vessel due to the failure of containment vent or occurrence of steam explosion, the amount of released radioactivity might amount to be at least equivalent to or surpass that of Chernobyl NPP accident. There existed still a risk that overheating and meltdown of nuclear fuels might reoccur with loss of cooling due to a possible giant aftershock. This article described total views on significant disaster that the accident brought about on many neighboring residents or wide range of people. After a general discussion about what was social responsibility of scientists, social responsibility of scientists for Fukushima Daiichi NPP accident was discussed. Responsibility of omission was also argued. (T. Tanaka)

Termination of light-water reactor core-melt accidents with a chemical core catcher: the core-melt source reduction system (COMSORS)

International Nuclear Information System (INIS)

Forsberg, C.W.; Parker, G.W.; Rudolph, J.C.; Osborne-Lee, I.W.; Kenton, M.A.

1996-09-01

The Core-Melt Source Reduction System (COMSORS) is a new approach to terminate light-water reactor core melt accidents and ensure containment integrity. A special dissolution glass is placed under the reactor vessel. If core debris is released onto the glass, the glass melts and the debris dissolves into the molten glass, thus creating a homogeneous molten glass. The molten glass, with dissolved core debris, spreads into a wide pool, distributing the heat for removal by radiation to the reactor cavity above or by transfer to water on top of the molten glass. Expected equilibrium glass temperatures are approximately 600 degrees C. The creation of a low-temperature, homogeneous molten glass with known geometry permits cooling of the glass without threatening containment integrity. This report describes the technology, initial experiments to measure key glass properties, and modeling of COMSORS operations

Severe Accident Mitigation by using Core Catcher applicable for Korea standard nuclear power plant

Energy Technology Data Exchange (ETDEWEB)

Park, Hae Kyun; Kim, Sang Nyung [Kyung Hee Univ., Yongin (Korea, Republic of)

2013-10-15

Nuclear power plants have been designed and operated in order to prevent severe accident because of their risk that contains tremendous radioactive materials that are potentially hazardous. Moreover, the government requested the nuclear industry to implement a severe accident management strategy for existing reactors to mitigate the risk of potential severe accidents. However, Korea standard nuclear power plant(APR-1400 and OPR-1000) are much more vulnerable for severe accident management than that of developed countries. Due to the design feature of reactor cavity in Korea standard nuclear power plant, inequable and serious Molten Core-Concrete Interaction(MCCI) may cause considerable safety problem to the reactor containment liner. At worst, it brings the release of radioactive materials to the environment. This accident applies to the fourth level of defense in depth(IAEA 1996), 'severe accident'. This study proposes and designs the 'slope' to secure reactor containment liner integrity when the corium spreads out from the destroyed reactor vessel to the reactor cavity due to the core melting accident. For this, make the initial corium distribution evenly exploit the 'slope' on the basis of the study of Ex-vessel corium behavior to prevent inequable and serious MCCI, in order to mitigate severe accident. The viscosity has a dominant position in the calculation. According to the result, the spread out distance on the slope is 10.7146841m, considering the rough surface of the concrete(slope) and margin of reactor cavity end(under 11m). Easy to design, production and economic feasibility are the advantage of the designed slope in this study. However, the slope design may unsuitable when the sequences of the accidents did not satisfy the assumptions as mentioned. Despite of those disadvantages, the slope will show a great performance to mitigate the severe accident. As mentioned in assumption, the corium releasing time property was

Severe Accident Mitigation by using Core Catcher applicable for Korea standard nuclear power plant

International Nuclear Information System (INIS)

Park, Hae Kyun; Kim, Sang Nyung

2013-01-01

Nuclear power plants have been designed and operated in order to prevent severe accident because of their risk that contains tremendous radioactive materials that are potentially hazardous. Moreover, the government requested the nuclear industry to implement a severe accident management strategy for existing reactors to mitigate the risk of potential severe accidents. However, Korea standard nuclear power plant(APR-1400 and OPR-1000) are much more vulnerable for severe accident management than that of developed countries. Due to the design feature of reactor cavity in Korea standard nuclear power plant, inequable and serious Molten Core-Concrete Interaction(MCCI) may cause considerable safety problem to the reactor containment liner. At worst, it brings the release of radioactive materials to the environment. This accident applies to the fourth level of defense in depth(IAEA 1996), 'severe accident'. This study proposes and designs the 'slope' to secure reactor containment liner integrity when the corium spreads out from the destroyed reactor vessel to the reactor cavity due to the core melting accident. For this, make the initial corium distribution evenly exploit the 'slope' on the basis of the study of Ex-vessel corium behavior to prevent inequable and serious MCCI, in order to mitigate severe accident. The viscosity has a dominant position in the calculation. According to the result, the spread out distance on the slope is 10.7146841m, considering the rough surface of the concrete(slope) and margin of reactor cavity end(under 11m). Easy to design, production and economic feasibility are the advantage of the designed slope in this study. However, the slope design may unsuitable when the sequences of the accidents did not satisfy the assumptions as mentioned. Despite of those disadvantages, the slope will show a great performance to mitigate the severe accident. As mentioned in assumption, the corium releasing time property was conservatively calculated

Investigation on multilayer failure mechanism of RPV with a high temperature gradient from core meltdown scenario

Energy Technology Data Exchange (ETDEWEB)

Jianfeng, Mao, E-mail: jianfeng-mao@163.com [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Engineering Research Center of Process Equipment and Remanufacturing, Ministry of Education (China); Xiangqing, Li [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Shiyi, Bao, E-mail: bsy@zjut.edu.cn [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Engineering Research Center of Process Equipment and Remanufacturing, Ministry of Education (China); Lijia, Luo [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Zengliang, Gao [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Engineering Research Center of Process Equipment and Remanufacturing, Ministry of Education (China)

2016-12-15

Highlights: • The multilayer failure mechanism is investigated for RPV under CHF. • Failure time and location of RPV are predicted under various SA scenarios. • The structural behaviors are analyzed in depth for creep and plasticity. • The effect of internal pressure and temperature gradient is considered. • The structural integrity of RPV is secured within the required 72 creep hours. - Abstract: The Fukushima accident shows that in-vessel retention (IVR) of molten core debris has not been appropriately assessed, and a certain pressure (up to 8.0 MPa) still exists inside the reactor pressure vessel (RPV). In the traditional concept of IVR, the pressure is supposed to successfully be released, and the temperature distributed among the wall thickness is assumed to be uniform. However, this concept is seriously challenged by reality of Fukushima accident with regard to the existence of both internal pressure and high temperature gradient. Therefore, in order to make the IVR mitigation strategy succeed, the numerical investigation of the lower head behavior and its failure has been performed for several internal pressures under high temperature gradient. According to some requirements in severe accident (SA) management of RPV, it should be ensured that the IVR mitigation takes effect in preventing the failure of the structure within a period of 72 h. Subsequently, the failure time and location have to be predicted under the critical heat flux (CHF) loading condition for lower head, since the CHF is limit thermal boundary before the melt-through of RPV. In illustrating the so called ‘multilayer failure mechanism’, the structural behaviors of RPV are analyzed in terms of the stress, creep strain, deformation, damage on selected paths.

Investigation on multilayer failure mechanism of RPV with a high temperature gradient from core meltdown scenario

International Nuclear Information System (INIS)

Jianfeng, Mao; Xiangqing, Li; Shiyi, Bao; Lijia, Luo; Zengliang, Gao

2016-01-01

Highlights: • The multilayer failure mechanism is investigated for RPV under CHF. • Failure time and location of RPV are predicted under various SA scenarios. • The structural behaviors are analyzed in depth for creep and plasticity. • The effect of internal pressure and temperature gradient is considered. • The structural integrity of RPV is secured within the required 72 creep hours. - Abstract: The Fukushima accident shows that in-vessel retention (IVR) of molten core debris has not been appropriately assessed, and a certain pressure (up to 8.0 MPa) still exists inside the reactor pressure vessel (RPV). In the traditional concept of IVR, the pressure is supposed to successfully be released, and the temperature distributed among the wall thickness is assumed to be uniform. However, this concept is seriously challenged by reality of Fukushima accident with regard to the existence of both internal pressure and high temperature gradient. Therefore, in order to make the IVR mitigation strategy succeed, the numerical investigation of the lower head behavior and its failure has been performed for several internal pressures under high temperature gradient. According to some requirements in severe accident (SA) management of RPV, it should be ensured that the IVR mitigation takes effect in preventing the failure of the structure within a period of 72 h. Subsequently, the failure time and location have to be predicted under the critical heat flux (CHF) loading condition for lower head, since the CHF is limit thermal boundary before the melt-through of RPV. In illustrating the so called ‘multilayer failure mechanism’, the structural behaviors of RPV are analyzed in terms of the stress, creep strain, deformation, damage on selected paths.

Accident source terms for boiling water reactors with high burnup cores.

Energy Technology Data Exchange (ETDEWEB)

Gauntt, Randall O.; Powers, Dana Auburn; Leonard, Mark Thomas

2007-11-01

The primary objective of this report is to provide the technical basis for development of recommendations for updates to the NUREG-1465 Source Term for BWRs that will extend its applicability to accidents involving high burnup (HBU) cores. However, a secondary objective is to re-examine the fundamental characteristics of the prescription for fission product release to containment described by NUREG-1465. This secondary objective is motivated by an interest to understand the extent to which research into the release and behaviors of radionuclides under accident conditions has altered best-estimate calculations of the integral response of BWRs to severe core damage sequences and the resulting radiological source terms to containment. This report, therefore, documents specific results of fission product source term analyses that will form the basis for the HBU supplement to NUREG-1465. However, commentary is also provided on observed differences between the composite results of the source term calculations performed here and those reflected NUREG-1465 itself.

Enhanced Accident Tolerant LWR Fuels National Metrics Workshop Report

Energy Technology Data Exchange (ETDEWEB)

Lori Braase

2013-01-01

The U.S. Department of Energy Office of Nuclear Energy (DOE-NE), in collaboration with the nuclear industry, has been conducting research and development (R&D) activities on advanced Light Water Reactor (LWR) fuels for the last few years. The emphasis for these activities was on improving the fuel performance in terms of increased burnup for waste minimization and increased power density for power upgrades, as well as collaborating with industry on fuel reliability. After the events at the Fukushima Nuclear Power Plant in Japan in March 2011, enhancing the accident tolerance of LWRs became a topic of serious discussion. In the Consolidated Appropriations Act, 2012, Conference Report 112-75, the U.S. Congress directed DOE-NE to: • Give “priority to developing enhanced fuels and cladding for light water reactors to improve safety in the event of accidents in the reactor or spent fuel pools.” • Give “special technical emphasis and funding priority…to activities aimed at the development and near-term qualification of meltdown-resistant, accident-tolerant nuclear fuels that would enhance the safety of present and future generations of light water reactors.” • Report “to the Committee, within 90 days of enactment of this act, on its plan for development of meltdown-resistant fuels leading to reactor testing and utilization by 2020.” Fuels with enhanced accident tolerance are those that, in comparison with the standard UO2-zirconium alloy system currently used by the nuclear industry, can tolerate loss of active cooling in the reactor core for a considerably longer time period (depending on the LWR system and accident scenario) while maintaining or improving the fuel performance during normal operations, and operational transients, as well as design-basis and beyond design-basis events. The overall draft strategy for development and demonstration is comprised of three phases: Feasibility Assessment and Down-selection; Development and Qualification; and

The role of fission gas in the analysis of hypothetical core disruptive accidents

Energy Technology Data Exchange (ETDEWEB)

Fischer, E A [Gesellschaft fuer Kernforschung mbH, INR Kernforschungszentrum, Karlsruhe (Germany)

1977-07-01

This paper summarizes recent work at Karlsruhe with the goal of understanding the effects of fission gas in hypothetical core disruptive accidents. The fission gas behavior model is discussed. The computer programs LANGZEIT and KURZZEIT describe the long-term and the transient gas behavior, respectively. Recent improvements in the modeling and a comparison of results with experimental data are reported. A somewhat detailed study of the role of fission gas in transient overpower (TOP) accidents was carried out. If pessimistic assumptions, like pin failure near the axial midplane are made, these accidents end in core disassembly. The codes HOPE and KADIS were used to analyze the initiating and the disassembly phase in these studies. Improvements of the codes are discussed. They include an automatic data transfer from HOPE to KADIS, and a new equation of state in KADIS, with an improved model for fission gas behavior. The analysis of a 15 cents/sec reactivity ramp accident is presented. Different pin failure criteria are used. In the cases selected, the codes predict an energetic disassembly. For the much discussed loss-of-flow driven TOP, detailed models are presently not available at Karlsruhe. Therefore, only a few comments and the results of a few scoping calculations will be presented.

Severe accident mitigation and core melt retention in the European pressurized reactor (EPR)

International Nuclear Information System (INIS)

Fischer, Manfred

2003-01-01

For the mitigation of severe accidents, the FPR has adopted and improved the defense-in-depth approaches of its predecessors, the French 'N4' and the German 'Konvoi' PWR's. Beyond these evolutionary changes, it includes a new, 4-th level of defense aimed at limiting the consequences of a postulated severe accident with core melting. This involves a strengthening of the confinement function and the avoidance of large early releases, by the prevention of scenarios and events with potentially high loads on the containment, incl. RPV failure at high pressure. The remaining low-pressure accidents are mitigated by dedicated design measures. The paper gives an overview and of the measures for H 2 -mitigation and steam explosion and focuses on a detailed description of the precautions and design measures for the stabilization and long-term cooling of the molten core. In the EPR the latter is achieved by melt spreading into a large outside-cooled crucible lateral to the pit, which is passively flooded and cooled with water from the IRWST. The separation of functions between pit and spreading room not only isolates the core catcher from the various loads during RPV failure, but also avoids any risks related to an unintended initiation of flooding during power operation. A stable state of the melt is reached after a few hours. Complete solidification is achieved within days. The core catcher can optionally be cooled actively by the CHRS, which avoids further steaming into the containment and establishes ambient pressure conditions in the long term. (author)

Dose estimation for nuclear power plant 4 accident in Taiwan at Fukushima nuclear meltdown emission level

International Nuclear Information System (INIS)

Tang, Mei-Ling; Tsuang, Ben-Jei; Kuo, Pei-Hsuan

2016-01-01

An advanced Gaussian trajectory dispersion model is used to evaluate the evacuation zone due to a nuclear meltdown at the Nuclear Power Plant 4 (NPP4) in Taiwan, with the same emission level as that occurred at Fukushima nuclear meltdown (FNM) in 2011. Our study demonstrates that a FNM emission level would pollute 9% of the island's land area with annual effective dose ≥50 mSv using the meteorological data on 11 March 2011 in Taiwan. This high dose area is also called permanent evacuation zone (denoted as PEZ). The PEZ as well as the emergency-planning zone (EPZ) are found to be sensitive to meteorological conditions on the event. In a sunny day under the dominated NE wind conditions, the EPZ can be as far as 100 km with the first 7-day dose ≥20 mSv. Three hundred sixty-five daily events using the meteorological data from 11 March 2011 to 9 March 2012 are evaluated. It is found that the mean land area of Taiwan in becoming the PEZ is 11%. Especially, the probabilities of the northern counties/cities (Keelung, New Taipei, Taipei, Taoyuan, Hsinchu City, Hsinchu County and Ilan County) to be PEZs are high, ranging from 15% in Ilan County to 51% in Keelung City. Note that the total population of the above cities/counties is as high as 10 million people. Moreover, the western valleys of the Central Mountain Range are also found to be probable being PEZs, where all of the reservoirs in western Taiwan are located. For example, the probability can be as high as 3% in the far southern-most tip of Taiwan Island in Pingtung County. This shows that the entire populations in western Taiwan can be at risk due to the shortage of clean water sources under an event at FNM emission level, especially during the NE monsoon period. - Highlights: • An advanced Gaussian-type trajectory model to evaluate the evacuation zone at Nuclear Power Plant 4 in Taiwan. • Mean land area of Taiwan in becoming the permanent evacuation zone is 11%. • The probabilities of the northern

Evaluation of Effect of Global Economic Meltdown on Capital Market Performance

Directory of Open Access Journals (Sweden)

ONAOLAPO ADEKUNLE RAHMAN

2013-07-01

Full Text Available The recent financial crisis that loomed the global economy was considered more inclusive than any other period of financial turmoil in the past 60 years. This paper evaluates the implications of the global economic meltdown on the Nigerian Capital Market Performance using the market capitalization of the Nigerian Stock Exchange as a major indicator. When the global economic meltdown came, it poses a recession on the Market Capitalization and the volume of share index of the Nation. This study depends entirely on secondary data in form of annual aggregate time series data of Market capitalization (dependent variable, exchange rate, interest rate, inflation rate, market share index with Dummy variable to represent the period of economic crisis. Ordinary least square of multiple regressions was used to analyze the data into econometric model while F-statistics was used to test for the formulated hypothesis. This study depicts that the global economic meltdown has a negative effect on the Capital Market Performance. It was therefore recommended that the Federal government and the regulatory agencies (CBN, NSE, SEC etc. should come up with intervention and fiscal policies that will suppress these effects and jumpstart the capital market and that the policies should be properly implemented and monitored.

Steady-state thermal hydraulic analysis and flow channel blockage accident analysis of JRR-3 silicide core

International Nuclear Information System (INIS)

Kaminaga, Masanori

1997-03-01

JRR-3 is a light water moderated and cooled, beryllium and heavy water reflected pool type research reactor using low enriched uranium (LEU) plate-type fuels. Its thermal power is 20 MW. The core conversion program from uranium-aluminum (UAl x -Al) dispersion type fuel (aluminide fuel) to uranium-silicon-aluminum (U 3 Si 2 -Al) dispersion type fuel (silicide fuel) is currently conducted at the JRR-3. This report describes about the steady-state thermal hydraulic analysis results and the flow channel blockage accident analysis result. In JRR-3, there are two operation mode. One is high power operation mode up to 20 MW, under forced convection cooling using the primary and the secondary cooling systems. The other is low power operation mode up to 200 kW, under natural circulation cooling between the reactor core and the reactor pool without the primary and the secondary cooling systems. For the analysis of the flow channel blockage accident, COOLOD code was used. On the other hand, steady-state thermal hydraulic analysis for both of the high power operation mode under forced convection cooling and low power operation under natural convection cooling, COOLOD-N2 code was used. From steady-state thermal hydraulic analysis results of both forced and natural convection cooling, fuel temperature, minimum DNBR etc. meet the design criteria and JRR-3 LEU silicide core has enough safety margin under normal operation conditions. Furthermore, flow channel blockage accident analysis results show that one channel flow blockage accident meet the safety criteria for accident conditions which have been established for JRR-3 LEU silicide core. (author)

APRI-7 Accident Phenomena of Risk Importance. A progress report on research in the field of severe accidents in 2009-2011; APRI-7 Accident Phenomena of Risk Importance. En laegesrapport om forskningen inom omraadet svaara haverier under aaren 2009-2011

Energy Technology Data Exchange (ETDEWEB)

Garis, Ninos; Agrell, Maria [SSM, Stockholm (Sweden); Glaenneskog, Henrik [Vattenfall Research and Development AB, Aelvkarleby (Sweden)] [and others

2012-11-01

Knowledge of the phenomena that may occur during severe accidents in a nuclear power plant is an important prerequisite for being able to predict the plant behavior, in order to formulate procedures and instructions for incident handling, for contingency planning, and to get good quality at the accident analysis and risk studies. Since the early 80's nuclear power companies and authorities in Sweden has collaborated in research on severe reactor accidents. Cooperation in the beginning was mostly linked to strengthening the protection against environmental impacts after a severe reactor accident, in particular to develop systems for filtered depressurization of the reactor containment. Since the early 90's the cooperation has partially changed and shifted to the phenomenological questions of risk dominance. During the years 2009-2011, cooperation continued in the research-program APRI-7. The aim was to show whether the solutions adopted in the Swedish strategy for accident management provides reasonable protection for the environment. This was done by gaining detailed knowledge of both important phenomena in the hearth melting behavior, and the amount of radioactivity that can be discharged to the surroundings during a severe accident. To achieve this aim, the research program has included a follow-up of international research in severe accidents and evaluation of results, and continued to support research at KTH and Chalmers Univ. of severe accidents. The follow-up of international research has promoted the exchange of knowledge and experience and has provided access to a wealth of information about various phenomena relevant to the events at severe accidents. This was important to obtain a good basis for assessment of abatement measures in the Swedish nuclear reactors. Continuing support to the Royal Inst. of Technology has provided increased knowledge about the ability to cool the molten core of the reactor vessel and the processes associated with

Systematic technology evaluation program for SiC/SiC composite-based accident-tolerant LWR fuel cladding and core structures: Revision 2015

Energy Technology Data Exchange (ETDEWEB)

Katoh, Yutai [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrani, Kurt A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-08-01

Fuels and core structures in current light water reactors (LWR’s) are vulnerable to catastrophic failure in severe accidents as unfortunately evidenced by the March 2011 Fukushima Dai-ichi Nuclear Power Plant Accident. This vulnerability is attributed primarily to the rapid oxidation kinetics of zirconium alloys in a water vapor environment at very high temperatures. Zr alloys are the primary material in LWR cores except for the fuel itself. Therefore, alternative materials with reduced oxidation kinetics as compared to zirconium alloys are sought to enable enhanced accident-tolerant fuels and cores.

Thermal conditions and functional requirements for molten fuel containment

International Nuclear Information System (INIS)

Kang, C.S.; Torri, A.

1980-05-01

This paper discusses the configuration and functional requirements for the molten fuel containment system (MFCS) in the GCFR demonstration plant design. Meltdown conditions following a loss of shutdown cooling (LOSC) accident were studied to define the core debris volume for a realistic meltdown case. Materials and thicknesses of the molten fuel container were defined. Stainless steel was chosen as the sacrificial material and magnesium oxide was chosen as the crucible material. Thermal conditions for an expected quasi-steady state were analyzed. Highlights of the functional requirements which directly affect the MFCS design are discussed

Papers presented as part of the status report of the Nuclear Safety Research Project of the Karlsruhe Nuclear Center on 23 March 1994

International Nuclear Information System (INIS)

Hueper, R.

1994-05-01

The ten papers deal with the state of safety requirements on future LWR plants and with nuclear safety research with regard to fast reactors and future PWR plants. In particular, passive after-heat removal, core disruptive accidents, and actinide burning in fast reactors are analysed. For PWR type plants the fuel element behaviour in the event of accidents, hydrogen distribution and hydrogen fires, and the origin and effects of steam explosions on the reactor pressure vessel and the containment are examined. Core meltdown cooling systems are suggested. (DG) [de

Evaluation of results of Phase B of the German Risk Study for Nuclear Power Plants

International Nuclear Information System (INIS)

Fischer, B.; Hahn, L.; Sailer, M.

1989-01-01

The expert opinion summarizes and discusses the intermediate and the final results of Phase B of the German Risk Study. Emphasis is placed on systems analyses and event scenarios, core melt-down scenarios and effects on the containment, failure of the containment and resulting source terms, radioactivity transport and consequences of accidents, multi-system emergencies and external disturbances, accident management and means of mitigation of damage. (DG) [de

Code package {open_quotes}SVECHA{close_quotes}: Modeling of core degradation phenomena at severe accidents

Energy Technology Data Exchange (ETDEWEB)

Veshchunov, M.S.; Kisselev, A.E.; Palagin, A.V. [Nuclear Safety Institute, Moscow (Russian Federation)] [and others

1995-09-01

The code package SVECHA for the modeling of in-vessel core degradation (CD) phenomena in severe accidents is being developed in the Nuclear Safety Institute, Russian Academy of Science (NSI RAS). The code package presents a detailed mechanistic description of the phenomenology of severe accidents in a reactor core. The modules of the package were developed and validated on separate effect test data. These modules were then successfully implemented in the ICARE2 code and validated against a wide range of integral tests. Validation results have shown good agreement with separate effect tests data and with the integral tests CORA-W1/W2, CORA-13, PHEBUS-B9+.

EPRTM engineered features for core melt mitigation in severe accidents

International Nuclear Information System (INIS)

Fischer, Manfred; Henning, Andreas

2009-01-01

For the prevention of accident conditions, the EPR TM relies on the proven 3-level safety concepts inherited from its predecessors, the French 'N4' and the German 'Konvoi' NPP. In addition, a new, fourth 'beyond safety' level is implemented for the mitigation of postulated severe accidents (SA) with core melting. It is aimed at preserving the integrity of the containment barrier and at significantly reducing the frequency and magnitude of activity releases into the environment under such extreme conditions. Loss of containment integrity is prevented by dedicated design measures that address short- and long-term challenges, like: the melt-through of the reactor pressure vessel under high internal pressure, energetic hydrogen/steam explosions, containment overpressure failure, and basemat melt-through. The EPR TM SA systems and components that address these issues are: - the dedicated SA valves for the depressurization the primary circuit, - the provisions for H 2 recombination, atmospheric mixing, steam dilution, - the core melt stabilization system, - the dedicated SA containment heat removal system. The core melt stabilization system (CMSS) of the EPR TM is based on a two-stage ex-vessel approach. After its release from the RPV the core debris is first accumulated and conditioned in the (dry) reactor pit by the addition of sacrificial concrete. Then the created molten pool is spread into a lateral core catcher to establish favorable conditions for the later flooding, quenching and cooling with water passively drained from the Internal Refueling Water Storage Tank. Long-term heat removal from the containment is achieved by sprays that are supplied with water by the containment heat removal system. Complementing earlier publications focused on the principle function, basic design, and validation background of the EPR TM CMSS, this paper describes the state achieved after detailed design, as well as the technical solutions chosen for its main components, including

Development of Lower Plenum Molten Pool Module of Severe Accident Analysis Code in Korea

International Nuclear Information System (INIS)

Son, Donggun; Kim, Dong-Ha; Park, Rae-Jun; Bae, Jun-Ho; Shim, Suk-Ku; Marigomen, Ralph

2014-01-01

To simulate a severe accident progression of nuclear power plant and forecast reactor pressure vessel failure, we develop computational software called COMPASS (COre Meltdown Progression Accident Simulation Software) for whole physical phenomena inside the reactor pressure vessel from a core heat-up to a vessel failure. As a part of COMPASS project, in the first phase of COMPASS development (2011 - 2014), we focused on the molten pool behavior in the lower plenum, heat-up and ablation of reactor vessel wall. Input from the core module of COMPASS is relocated melt composition and mass in time. Molten pool behavior is described based on the lumped parameter model. Heat transfers in between oxidic, metallic molten pools, overlying water, steam and debris bed are considered in the present study. The models and correlations used in this study are appropriately selected by the physical conditions of severe accident progression. Interaction between molten pools and reactor vessel wall is also simulated based on the lumped parameter model. Heat transfers between oxidic pool, thin crust of oxidic pool and reactor vessel wall are considered and we solve simple energy balance equations for the crust thickness of oxidic pool and reactor vessel wall. As a result, we simulate a benchmark calculation for APR1400 nuclear power plant, with assumption of relocated mass from the core is constant in time such that 0.2ton/sec. We discuss about the molten pool behavior and wall ablation, to validate our models and correlations used in the COMPASS. Stand-alone SIMPLE program is developed as the lower plenum molten pool module for the COMPASS in-vessel severe accident analysis code. SIMPLE program formulates the mass and energy balance for water, steam, particulate debris bed, molten corium pools and oxidic crust from the first principle and uses models and correlations as the constitutive relations for the governing equations. Limited steam table and the material properties are provided

Radiation accidents

International Nuclear Information System (INIS)

Saenger, E.L.

1986-01-01

It is essential that emergency physicians understand ways to manage patients contaminated by radioactive materials and/or exposed to external radiation sources. Contamination accidents require careful surveys to identify the metabolic pathway of the radionuclides to guide prognosis and treatment. The level of treatment required will depend on careful surveys and meticulous decontamination. There is no specific therapy for the acute radiation syndrome. Prophylactic antibodies are desirable. For severely exposed patients treatment is similar to the supportive care given to patients undergoing organ transplantation. For high-dose extremity injury, no methods have been developed to reverse the fibrosing endarteritis that eventually leads to tissue death so frequently found with this type of injury. Although the Three Mile Island episode of March 1979 created tremendous public concern, there were no radiation injuries. The contamination outside the reactor building and the release of radioiodine were negligible. The accidental fuel element meltdown at Chernobyl, USSR, resulted in many cases of acute radiation syndrome. More than 100,000 people were exposed to high levels of radioactive fallout. The general principles outlined here are applicable to accidents of that degree of severity

Examination of off-site emergency protective measures for core melt accidents

International Nuclear Information System (INIS)

Aldrich, D.C.; Ericson, D.M. Jr.; Jones, R.B.

1978-01-01

Results from the Reactor Safety Study (RSS) have shown that to cause significant impacts off-site, i.e., sufficient quantities of biologically important radionuclides released, it is necessary to have a core melt accident. To mitigate the impact of such potential accidents, the design of appropriate emergency response actions requires information as to the relative merit of publicly available protective measures. In order to provide this information, a study using the consequence model developed for the RSS is being conducted to evaluate (in terms of reduced public health effects and dose exposure) potential off-site protective strategies. The paper describes the methods being used in the study as well as the results and conclusions obtained

Neutronic analysis of LMFBRs during severe core disruptive accidents

International Nuclear Information System (INIS)

Tomlinson, E.T.

1979-01-01

A number of numerical experiments were performed to assess the validity of diffusion theory and various perturbation methods for calculating the reactivity state of a severely disrupted liquid metal cooled fast breeder reactor (LMFBR). The disrupted configurations correspond, in general, to phases through which an LMFBR core could pass during a core disruptive accident (CDA). Two-reactor models were chosen for this study, the two zone, homogeneous Clinch River Breeder Reactor and the Large Heterogeneous Reactor Design Study Core. The various phases were chosen to approximate the CDA results predicted by the safety analysis code SAS3D. The calculational methods investigated in this study include the eigenvalue difference technique based on both discrete ordinate transport theory and diffusion theory, first-order perturbation theory, exact perturbation theory, and a new hybrid perturbation theory. Selected cases were analyzed using Monte Carlo methods. It was found that in all cases, diffusion theory and perturbation theory yielded results for the change in reactivity that significantly disagreed with both the discrete ordinate and Monte Carlo results. These differences were, in most cases, in a nonconservative direction

Analysis of the core reflooding of a PWR reactor under a loss-of-coolant postulated accident

International Nuclear Information System (INIS)

Austregesilo Filho, H.

1978-12-01

The main purpose of this work is to analyse the termohydraulic behaviour of emergency cooling water, during reflooding of a PWR core submitted to a postulated loss-of-coolant accident, with the scope of giving the boundary conditions needed to verify fuel element and containment integrity. The analytical model presented was applied to the simulation of Angra I core reflooding phase, after a double-ended break between pressure vessel and discharge of one of the main coolant pumps. For this accident, with a discharge coefficient of C sub(D) = 0.4, the highest peak cladding temperature is expected. (author) [pt

Evaluation of long-term post-accident core cooling of Three Mile Island Unit 2

Energy Technology Data Exchange (ETDEWEB)

None

1979-04-15

On the basis of current understanding of the accident scenario and available data, the staff reports here on its evaluation of the condition of the core and the core flow resistance as it might affect ability to cool the core by natural circulation. The natural circulation cooling capability of TMI-2 for the estimated core flow resistance and a variety of other conditions is evaluated and a comparison of the Base Case and off-nominal plant configurations is presented. The potential for and effects of natural convection core cooling are addressed, and the staff recommendations for reactor performance acceptance criteria upon initiation of natural convection are presented.

Determination of the availability of core exit thermocouples during severe accident situations

International Nuclear Information System (INIS)

Edson, J.L.

1985-04-01

This report presents the findings and recommendations of the Nuclear Power Plant Instrumentation Evaluation (NPPIE) program concerning signal validation methods to determine the on-line availability of core exit thermocouples during accident situations. Methods of selecting appropriate signal validation techniques are discussed and sources of error identified. This report shows that through the use of these techniques the existence of high-temperature-caused errors may be detected as they occur. Specific recommendations for application of selected signal validation techniques to core exit thermocouples and other measurement systems are made. 23 refs., 22 figs., 3 tabs

Core disruptive accident and recriticality analysis with FX2-POOL

International Nuclear Information System (INIS)

Abramson, P.B.

1976-01-01

The current state of development of FX2-POOL, a two-dimensional hydrodynamic, thermodynamic and neutronic scoping model for Hypothetical Core Disruptive Accident analysis is described. Checkout comparisons to VENUS for prompt burst conditions were good. Use of FX2-POOL to examine the importance of fuel to steel heat transfer during a prompt burst indicates that heat transfer plays no important role on that time scale. Scoping studies of material thermohydrodynamics for about 20 to 30 milliseconds following the prompt burst indicate that heat transfer is important on the time scale necessary for the CDA bubble to grow to the size of the original core. Preliminary results are presented for energetics of boiling fuel steel pools which are forced recritical by local surface pressurization

Software concepts for the build-up of complex systems - selection and realization taking as example a program system for calculation of hypothetical core meltdown accidents

International Nuclear Information System (INIS)

Scheuermann, W.

1994-10-01

Development and application of simulation systems for the analysis of complex processes require on the one hand and detailed engineering knowledge of the plant and the processes to be simulated and on the other hand a detailled knowledge about software engineering, numerics and data structures. The cooperation of specialists of both areas will become easier if it is possible to reduce the complexicity of the problems to be solved in a way that the analyses will not be disturbed and the communication between different disciplines will not become unnecessarily complicated. One solution to reduce the complexity is to consider computer science as an engineering discipline which provides mainly abstract elements and to allow engineers to build application systems based on these abstract elements. The principle of abstraction leads through the processes of modularisation and the solution of the interface problem to an almost problem independent system architecture where the elements of the system (modules, model components and models) operate only on those data assigned to them. In addition the development of abstract data types allows the formal description of the relations and interactions between system elements. This work describes how these ideas can be concretized to build complex systems which allow reliable and effective problem solutions. These ideas were applied successfully during the design, realization and application of the code system KESS, which allows the analysis of core melt down accidents in pressurized water reactors. (orig.) [de

Nuclear Safety Project. Annual report 1986

International Nuclear Information System (INIS)

1987-09-01

The annual report 1986 is a detailed description of work within the Nuclear Safety Project performed in 1986 in the nuclear safety field by KfK institutes and departments and by external institutes on behalf of KfK. It includes individual research activities on dynamic loads and strains of reactor components under accident conditions, fuel behaviour under accident conditions, investigation and control of LWR core-meltdown accidents, improvement of fission product retention and reduction of radiation exposure, and on behaviour, impact and removal of released pollutants. (DG)

Assessment of mass fraction and melting temperature for the application of limestone concrete and siliceous concrete to nuclear reactor basemat considering molten core-concrete interaction

Energy Technology Data Exchange (ETDEWEB)

Lee, Ho Jae; Kim, Do Gyeum [Korea Institute of Civil Engineering and Building Technology, Goyang (Korea, Republic of); Cho, Jae Leon [Korea Hydro and Nuclear Power Co., Ulsan (Korea, Republic of); Yoon, Eui Sik [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of); Cho, Myung Suk [Korea Hydro and Nuclear Power Co., Central Research Institute, Daejeon (Korea, Republic of)

2016-04-15

Severe accident scenarios in nuclear reactors, such as nuclear meltdown, reveal that an extremely hot molten core may fall into the nuclear reactor cavity and seriously affect the safety of the nuclear containment vessel due to the chain reaction caused by the reaction between the molten core and concrete. This paper reports on research focused on the type and amount of vapor produced during the reaction between a high-temperature molten core and concrete, as well as on the erosion rate of concrete and the heat transfer characteristics at its vicinity. This study identifies the mass fraction and melting temperature as the most influential properties of concrete necessary for a safety analysis conducted in relation to the thermal interaction between the molten core and the basemat concrete. The types of concrete that are actually used in nuclear reactor cavities were investigated. The H2O content in concrete required for the computation of the relative amount of gases generated by the chemical reaction of the vapor, the quantity of CO2 necessary for computing the cooling speed of the molten core, and the melting temperature of concrete are evaluated experimentally for the molten core-concrete interaction analysis.

Reactor containment depressurization and filtration equipment for use in the case of a serious accident

International Nuclear Information System (INIS)

L'Homme, A.

1987-06-01

A study was carried out under the aegis of the OECD into filtered vented containment systems which permit depressurization of the containment and filtration of the effluents released to the environment, in the event of a major accident with a pressurized water reactor (PWR) (or BWR or CANDU type reactors) involving core meltdown, with a view to minimizing the consequences. This paper describes the various systems examined which could possibly be used for this purpose. These comprised the French robust sand filtration system, the Swedish FILTRA system, the vacuum containment and discharge and emergency filtration system used by the CANDU plants of the Ontario-Hydro electricity company in Canada and the BWR pressure-suppression pounds. The positions of the various national authorities regarding incorporation of such systems into nuclear power plants, the design and technical principles underlying the systems, the procedures and criteria for their use and their advantages and disadvantages are examined [fr

Research activities at JAERI on core material behaviour under severe accident conditions

International Nuclear Information System (INIS)

Uetsuka, H.; Katanashi, S.; Ishijima, K.

1996-01-01

At the Japan Atomic Energy Research Institute (JAERI), experimental studies on physical phenomena under the condition of a severe accident have been conducted. This paper presents the progress of the experimental studies on fuel and core materials behaviour such as the thermal shock fracture of fuel cladding due to quenching, the chemical interaction of core materials at high temperatures and the examination of TMI-2 debris. The mechanical behaviour of fuel rod with heavily embrittled cladding tube due to the thermal shock during delayed reflooding have been investigated at the Nuclear Safety Research Reactor (NSSR) of JAERI. A test fuel rod was heated in steam atmosphere by both electric and nuclear heating using the NSSR, then the rod was quenched by reflooding at the test section. Melting of core component materials having relatively low melting points and their eutectic reaction with other materials significantly influence on the degradation and melt down of fuel bundles during severe accidents. Therefore basic information on the reaction of core materials is necessary to understand and analyze the progress of core melting and relocation. Chemical interactions have been widely investigated at high temperatures for various binary systems of core component materials including absorber materials such as Zircaloy/Inconel, Zircaloy/stainless steel, Zircaloy/(Ag-In-Cd), stainless steel B 4 C and Zircaloy/B 4 C. It was found that the reaction generally obeyed a parabolic rate law and the reaction rate was determined for each reaction system. Many debris samples obtained from the degraded core of TMI-2 were transported to JAERI for numerous examinations and analyses. The microstructural examination revealed that the most part of debris was ceramic and it was not homogeneous in a microscopic sense. The thermal diffusivity data was also obtained for the temperature range up to about 1800K. The data from the large scale integral experiments were also obtained through the

Thermohydraulics in a high-temperature gas-cooled reactor prestressed-concrete reactor vessel during unrestricted core-heatup accidents

International Nuclear Information System (INIS)

Kroeger, P.G.; Colman, J.; Araj, K.

1983-01-01

The hypothetical accident considered for siting considerations in High Temperature Gas-Cooled Reactors (HTGR) is the so called Unrestricted Core Heatup Accident (UCHA), in which all forced circulation is lost at initiation, and none of the auxillary cooling loops can be started. The result is a gradual slow core heatup, extending over days. Whether the liner cooling system (LCS) operates during this time is of crucial importance. If it does not, the resulting concrete decomposition of the prestressed concrete reactor vessel (PCRV) will ultimately cause containment building (CB) failure after about 6 to 10 days. The primary objective of the work described here was to establish for such accident conditions the core temperatures and approximate fuel failure rates, to check for potential thermal barrier failures, and to follow the PCRV concrete temperatures, as well as PCRV gas releases from concrete decomposition. The work was done for the General Atomic Corporation Base Line Zero reactor of 2240 MW(t). Most results apply at least qualitatively also to other large HTGR steam cycle designs

Analysis of natural convection in volumetrically-heated melt pools

International Nuclear Information System (INIS)

Sehgal, B.R.; Dinh, T.N.; Nourgaliev, R.R.

1996-12-01

Results of series of studies on natural convection heat transfer in decay-heated core melt pools which form in a reactor lower plenum during the progression of a core meltdown accident are described. The emphasis is on modelling and prediction of turbulent heat transfer characteristics of natural convection in a liquid pool with an internal energy source. Methods of computational fluid dynamics, including direct numerical simulation, were applied for investigation

Analysis of the primary source term for meltdown accidents using MELCOR 1.8.2; Analyse des primaeren Quellterms bei Kernschmelzunfaellen mit MELCOR 1.8.2

Energy Technology Data Exchange (ETDEWEB)

Schmuck, P.

1995-08-01

The MELCOR code describing accident phenomena in the core and primary systems was used for source term calculations and - in the context of the MELCOR Cooperative Assessment Programme - for studying two-phase flows through components such as valves and chokes. Results of the latter studies in comparison to experiments gave hints for an improved calculation of momentum transfer between the phases. (orig.)

Analysis of forces on core structures during a loss-of-coolant accident. Final report

International Nuclear Information System (INIS)

Griggs, D.P.; Vilim, R.B.; Wang, C.H.; Meyer, J.E.

1980-08-01

There are several design requirements related to the emergency core cooling which would follow a hypothetical loss-of-coolant accident (LOCA). One of these requirements is that the core must retain a coolable geometry throughout the accident. A possible cause of core damage leading to an uncoolable geometry is the action of forces on the core and associated support structures during the very early (blowdown) stage of the LOCA. An equally unsatisfactory design result would occur if calculated deformations and failures were so extensive that the geometry used for calculating the next stages of the LOCA (refill and reflood) could not be known reasonably well. Subsidiary questions involve damage preventing the operation of control assemblies and loss of integrity of other needed safety systems. A reliable method of calculating these forces is therefore an important part of LOCA analysis. These concerns provided the motivation for the study. The general objective of the study was to review the state-of-the-art in LOCA force determination. Specific objectives were: (1) determine state-of-the-art by reviewing current (and projected near future) techniques for LOCA force determination, and (2) consider each of the major assumptions involved in force determination and make a qualitative assessment of their validity

Comparative analysis of unprotected loss-of-flow accidents for the 1.0 m EFR-LVC core using different computer codes

International Nuclear Information System (INIS)

Royl, P.; Frizonnet, J.M.; Moran, J.

1993-02-01

A comparative analysis of the unprotected loss of flow (ULOF) accident has been performed for the LVC core (Lower Void Core) of the European Fast Reactor EFR with the FRAX5B and FRAX5C codes from the AEA-T, the PHYSURAC code from CEA and the SAS4A REF92 code system developed jointly between KfK, CEA and PNC. The accident is triggered by the run down of the coolant pumps with failure to trip the reactor by the primary and/or secondary shutdown system. Only a limited amount of mitigating reactivity from the third shutdown line was considered so that the accident can progress into boiling and core disruption. This code outlines the important modelling differences and compares the different simulations. The discussion of the rather wide spectrum of calculated accident progressions identifies the generic differences, relates them to the applied models, and summarizes the key points that are responsible for the different progressions. A comparison of the consequence spectrum from all simulations indicates zero work energies for the majority of the calculations. All simulations show up the need for a continued accident analysis into the early and late transition phase

Standards and guidelines should be rules between licensees and regulators

International Nuclear Information System (INIS)

Narabayashi, Tadashi

2014-01-01

The 2011 off the Pacific coast of Tohoku Pacific Earthquake and the Tsunami gave the serious damage to the Fukushima-Daiichi Nuclear Power Plants (NPPs). The accidents occurred in Unit 1, 2, 3 and 4. It is said that the height of tsunami attacked Fukushima NPP was more than 14m. After 50 minutes from the automatic shut-down, tsunami attacked the NPPs in Fukushima Daiichi NPPs. For example, the Unit 1 lost A/C power caused the loss of water injection function; it made the core meltdown and unusual increase of PCV pressure in the midnight of March 11th to 12th morning. Though the Unit one has the Isolation Condenser Core Cooling system, it was stopped by the operator to keep the cooling rate of 55degC/h. Finally, the isolation signal was transmitted from the control room to the motor driven isolation valves when the control room's battery discharged. It was the initiation of the core meltdown. The lessons from the accidents, we should improve the nuclear safety regulation through the innovation of regulatory rules and safety standards. Standards and guidelines should be rules between licensees and regulators. (author)

The Analysis of Surrounding Structure Effect on the Core Degradation Progress with COMPASS Code

Energy Technology Data Exchange (ETDEWEB)

Bae, Jun Ho; Son, Dong Gun; Kim, Jong Tae; Park, Rae Jun; Kim, Dong Ha [KAERI, Daejeon (Korea, Republic of)

2015-05-15

In line with the importance of severe accident analysis after Fukushima accident, the development of integrated severe accident code has been launched by the collaboration of three institutes in Korea. KAERI is responsible to develop modules related to the in-vessel phenomena, while other institutes are to the containment and severe accident mitigation facility, respectively. In the first phase, the individual severe accident module has been developed and the construction of integrated analysis code is planned to perform in the second phase. The basic strategy is to extend the design basis analysis codes of SPACE and CAP, which are being validated in Korea for the severe accident analysis. In the first phase, KAERI has targeted to develop the framework of severe accident code, COMPASS (COre Meltdown Progression Accident Simulation Software), covering the severe accident progression in a vessel from a core heat-up to a vessel failure as a stand-alone fashion. In order to analyze the effect of surrounding structure, the melt progression has been compared between the central zone and the most outer zone under the condition of constant radial power peaking factor. Figure 2 and 3 shows the fuel element temperature and the clad mass at the central zone, respectively. Due to the axial power peaking factor, the axial node No.3 has the highest temperature, while the top and bottom nodes have the lowest temperature. When the clad temperature reaches to the Zr melting temperature (2129.15K), the Zr starts to melt. The axial node No.2 reaches to the fuel melting temperature about 5000 sec and the molten fuel relocates to the node No.1, which results to the blockage of flow area in node No.1. The blocked flow area becomes to open about 6100 sec due to the molten ZrO{sub 2} mass relocation to core support plate. Figure 4 and 5 shows the fuel element temperature and the clad mass at the most outer zone, respectively. It is shown that the fuel temperature increase more slowly

Apparatus for controlling molten core debris

International Nuclear Information System (INIS)

Golden, M.P.; Tilbrook, R.W.; Heylmun, N.F.

1972-01-01

Disclosed is an apparatus for containing, cooling, diluting, dispersing and maintaining subcritical the molten core debris assumed to melt through the bottom of a nuclear reactor pressure vessel in the unlikely event of a core meltdown. The apparatus is basically a sacrificial bed system which includes an inverted conical funnel, a core debris receptacle including a spherical dome, a spherically layered bed of primarily magnesia bricks, a cooling system of zig-zag piping in graphite blocks about and below the bed and a cylindrical liner surrounding the graphite blocks including a steel shell surrounded by firebrick. Tantalum absorber rods are used in the receptacle and bed. 9 claims, 22 figures

Safety analysis of RA reactor operation, I-III, Part III - Environmental effect of the maximum credible accident; Analiza sigurnosti rada reaktora RA - I-III, III deo - Posledica maksimalno moguceg akcidenta na okolinu reaktora

Energy Technology Data Exchange (ETDEWEB)

Raisic, N [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1963-02-15

Maximum credible accident at the RA reactor would consider release of fission products into the environment. This would result from fuel elements failure or meltdown due to loss of coolant. The analysis presented in this report assumes that the reactor was operating at nominal power at the moment of maximum possible accident. The report includes calculations of fission products activity at the moment of accident, total activity release during the accident, concentration of radioactive material in the air in the reactor neighbourhood, and the analysis of accident environmental effects.

Thermo-physical properties of corium: development of an assessed data base for severe accident applications

Energy Technology Data Exchange (ETDEWEB)

Strizhov, V.F.; Galimov, R.G.; Ozrin, V.D. [Nuclear Safety Institute of the Russian Academy of Sciences, Moscow (Russian Federation); Yu Zitserman, V.; Kobzev, G.I.; Fokin, L.R. [Institute of high temperatures, Russian Academy of Sciences, Moscow (Russian Federation); Piluso, P. [CEA Cadarache (DEN/DTN/STRI), Lab. d' essais pour la Maitrise des Accidents graves, 13 - Saint Paul lez Durance (France); Chalaye, H. [CEA Saclay, Dir. de l' Energie Nucleaire, 91 - Gif sur Yvette (France)

2007-07-01

In a hypothetical case of a core melt-down scenarios a very high temperature would be reached (up to 3000 K). In this case, the materials of the core and structural materials (fuel, cladding, metallic alloys, concrete, etc.) could melt to form complex and aggressive mixtures called corium. Modelling of severe accident phenomena, code development and assessments of nuclear safety require a reliable knowledge of the thermophysical properties of corium at wide temperature range (below solidus temperature, between solidus and liquidus temperature and above the liquidus temperature). Common Russian-French project ISTC 3078, has been devoted to the development, assessment and recommendation for the establishment of a reliable thermophysical data base for severe accident applications. The project consists of two tasks related to properties of pure metallic (U, Zr, Fe, Cr, Ni) and oxide (UO{sub 2}, U{sub 3}O{sub 8}, U{sub 4}O{sub 9}, NiO, ZrO{sub 2}, Cr{sub 2}O{sub 3}, FeO, Fe{sub 2}O{sub 3}, Fe{sub 3}O{sub 4}, Al{sub 2}O{sub 3}, CaO, MgO, SiO{sub 2}, HfO{sub 2}, CeO{sub 2}) components, and mixtures relevant to severe accident conditions. Three categories of data (on UPAK classification) were considered: experimental data, critically evaluated data, and predicted data. The data of the first category is a result of specific experiment, data of the second category is a result of the analysis of data consistency and co-processing (expert and statistical) obtained in several experiments, data of the third category are based on model estimates, using correlations between different physical properties. The process of assessing, review and development of recommendation is described in the paper and illustrated by examples on thermophysical properties. (authors)

RA reactor safety analysis I-III, Part III - Environmental effect of the maximum credible accident; Analiza sigurnosti rada Reaktora RA I-III, III deo - Posledica maksimalno moguceg akcidenta na okolinu reaktora

Energy Technology Data Exchange (ETDEWEB)

Raisic, N [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1963-02-15

The objective of the maximum credible accident analysis was to determine the integral radiation doses in the vicinity of the reactor and in the environment. In case of RA reactor the maximum credible accident, meaning release of the fission products, would be caused by fuel elements meltdown. This analysis includes the following calculation results: activity of the fission products, volatility of the fission products, concentration of radioactive materials in the air, analysis of the accident environmental effects.

Control rod drop accident analysis for the mixed core project in Ling Ao NPS

International Nuclear Information System (INIS)

Zhang Shishun; Zhou Zhou; Xiao Min

2004-01-01

AFA-2G assemblies in Ling Ao NPS (LNPS) have been replaced gradually by AFA-3G assemblies from cycle 2 and subsequent cycles. the enrichment of the fuels will be increased from 3.2% to 3.7% from cycle 3 in Ling Ao. Therefore, the study of ling Ao mixed core and increased enrichment have been performed since 2001. Lots of accidents need to be re-analyzed in Ling Ao NPS in order to verify its safety requirements for the new fuel management. Control rod drop accident for LNPS was re-analyzed in 2001 in frame of FRAMATOME ANP analytical methodology. The analytical codes used in the accident analysis include SCIENCE, ESPADON, CINEMA, CANTAL and FLICA III. The control rod drop accident analysis is performed with respect to the 10 reference cycles of the generic fuel management design for Ling Ao mixed core and increased enrichment study. The pre-drop FδH for the first transition cycles and other cycles are 1.52 and 1.55, respectively. For detected dropped rod configurations, the negative flux rate protection system actuates a reactor trip. For the non-detected dropped rod configurations, the minimum DNBR values have been evaluated with conservative analysis methodology and assumptions and the DNBR fuel design limit is respected the analytical results shows that, for all the non-detected dropped rod configurations, the minimum DNB margin is about 2% which occurs in AFA-2G fuel assembly in the first transition cycle. (author)

Fuel and control rod failure behavior during degraded core accidents

International Nuclear Information System (INIS)

Chung, K.S.

1984-01-01

As a part of the pretest and posttest analyses of Light Water Reactor Source Term Experiments (STEP) which are conducted in the Transient Reactor Test (TREAT) facility, this paper investigates the thermodynamic and material behaviors of nuclear fuel pins and control rods during severe core degradation accidents. A series of four STEP tests are being performed to simulate the characteristics of the power reactor accidents and investigate the behavior of fission product release during these accidents. To determine the release rate of the fission products from the fuel pins and the control rod materials, information concerning the timing of the clad failure and the thermodynamic conditions of the fuel pins and control rods are needed to be evaluated. Because the phase change involves a large latent heat and volume expansion, and the phase change is a direct cause of the clad failure, the understanding of the phase change phenomena, particularly information regarding how much of the fuel pin and control rod materials are melted are very important. A simple energy balance model is developed to calculate the temperature profile and melt front in various heat transfer media considering the effects of natural convection phenomena on the melting and freezing front behavior

Third generation nuclear plants

Science.gov (United States)

Barré, Bertrand

2012-05-01

After the Chernobyl accident, a new generation of Light Water Reactors has been designed and is being built. Third generation nuclear plants are equipped with dedicated systems to insure that if the worst accident were to occur, i.e. total core meltdown, no matter how low the probability of such occurrence, radioactive releases in the environment would be minimal. This article describes the EPR, representative of this "Generation III" and a few of its competitors on the world market.

Specialists' meeting on role of fission products in whole core accidents

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-07-01

Safety of nuclear reactors has been a central concern of the nuclear energy industry from the very beginning. This concern, and the resultant excellence of design, fabrication, and operation, aided by extensive engineered safety features, has given nuclear energy its superior record of protection of the environment and of the public health and safety. With respect to the fast reactor, it was recognized early in the program that there exists a theoretical possibility of a core compaction leading to significant energy release. The considerations of fission product effects are primarily on of the main concerns in evaluation of safety issues. Since fission products have the potential for dispersing fuel from the core region and thereby producing reactor shutdown, knowledge of their effects can contribute to demonstrating that there is a low probability producing whole-core involvement. Similarly, knowledge of fission product effects can contribute to demonstrating that there is a low probability of a whole-core disruptive accident leading to sufficient energy release to challenge the containment capability.

Specialists' meeting on role of fission products in whole core accidents

International Nuclear Information System (INIS)

1977-01-01

Safety of nuclear reactors has been a central concern of the nuclear energy industry from the very beginning. This concern, and the resultant excellence of design, fabrication, and operation, aided by extensive engineered safety features, has given nuclear energy its superior record of protection of the environment and of the public health and safety. With respect to the fast reactor, it was recognized early in the program that there exists a theoretical possibility of a core compaction leading to significant energy release. The considerations of fission product effects are primarily on of the main concerns in evaluation of safety issues. Since fission products have the potential for dispersing fuel from the core region and thereby producing reactor shutdown, knowledge of their effects can contribute to demonstrating that there is a low probability producing whole-core involvement. Similarly, knowledge of fission product effects can contribute to demonstrating that there is a low probability of a whole-core disruptive accident leading to sufficient energy release to challenge the containment capability

Preventing another Chernobyl: codes, practices, and the role of new technology

International Nuclear Information System (INIS)

Egan, J.R.

1988-01-01

Preventative steps to prevent and mitigate the consequences of a nuclear accident are considered. The national and international legislation now available is mentioned elsewhere in the book. This chapter discusses the role of codes of conduct and personal agreements which could also prevent nuclear accidents. It is suggested that a radical departure from existing nuclear technology is needed. In particular some definite goals and objectives are suggested. The first is that there should be no meltdowns - all reactors must be physically incapable of core meltdown or explosion under any circumstances. This would mean no huge emergency evacuation plans, no need for expensive emergency core cooling systems. No spiralling cost overruns, no nuclear waste problem, no more huge reactors too big for national electrical systems, no military complications, no intractable decommissionings and no quality control problems are also given as goals. Some of these goals could be achieved with inherently safe reactor designs, much smaller reactors and factory assembly, rather than on-site construction. Other suggestions are also made to achieve the proposed new nuclear technology. (U.K.)

MELPROG/TRAC: update and applications

International Nuclear Information System (INIS)

Henninger, R.J.; Kelly, J.E.

1986-01-01

The first complete, coupled, and mechanistic analysis of a core meltdown sequence has been made with MELPROG-PWR/MOD1 and MELPROG/TRAC. The sequence analyzed was a station blackout accident for the Surry plant. Through vessel failure, all important aspects of the meltdown sequence were calculated. This version of MELPROG permits a full two-dimensional treatment of the in-vessel phenomena. Natural circulation can thus be modeled. Comparison to one-dimensional MELPROG and MARCH calculations shows that natural circulation reduces the rate of core heating, but increases the rate of heating of upper plenum structures and primary piping. This increased heating can inhibit fission product deposition and may lead to an early failure of the primary system. Because of uncertainty, sensitivity studies were performed to assess the relative importance of modeling assumptions. Changes in the modeling of the initial fuel rod melting and relocation were found to vary the hydrogen source by a factor of 2 and alter the timing of key events. These results imply that accurate and mechanistic modeling is important for severe accident sequence analysis

Lessons from the Russian meltdown : the economics of soft legal constraints

NARCIS (Netherlands)

Perotti, E.C.

2001-01-01

On August 17, 1998, Russia defaulted on its domestic public debt, declared a moratorium on the private banks foreign liabilities which was equivalent to an outright default, and abandoned its exchange rate regime. The depth of the Russian meltdown shocked the international markets, and precipitated

Lessons from the Russian meltdown : the economics of soft legal constraints

NARCIS (Netherlands)

Perotti, E.C.

2002-01-01

On August 17, 1998, Russia defaulted on its domestic public debt, declared a moratorium on the private banks foreign liabilities which was equivalent to an outright default, and abandoned its exchange rate regime. The depth of the Russian meltdown shocked the international markets, and precipitated

A Primer on Financial System Meltdown. The Economists' View

OpenAIRE

Hahn, Franz R.

2008-01-01

Ideologues are quick to explain the current financial meltdown: it's the markets, stupid. Economists agree but add: it's politics too, stupid. Ideologues agree but counter: first and foremost it's capitalism, stupid. Economists agree but reply: §$%&?!, stupid. This is where this short paper takes us: it makes an attempt to give a brief overview of the economists' views on the ongoing financial system crisis explaining "§$%&?!, stupid".

Prevention and investigations of core degradation in case of beyond design accidents of the 2400 MWTH gas-cooled fast reactor

International Nuclear Information System (INIS)

Bertrand, F.; Gatin, V.; Bentivoglio, F.; Gueneau, C.

2011-01-01

The present paper deals with studies carried out to assess the ability of the core of the Gas Fast Reactor (GFR) to withstand beyond design accidents. The work presented here is aimed at simulating the behaviour of this core by using analytical models whose input parameters are calculated with the CATHARE2 code. Among possible severe accident initiators, the Unprotected Loss Of Coolant Accident (ULOCA of 3 Inches diameter) is investigated in detail in the paper with CATHARE2. Additionally, a simplified pessimistic assessment of the effect of a postulated power excursion that could result from the failure of prevention provisions is presented. (author)

Analysis of natural convection in volumetrically-heated melt pools

Energy Technology Data Exchange (ETDEWEB)

Sehgal, B.R.; Dinh, T.N.; Nourgaliev, R.R. [Royal Inst. of Tech., Stockholm (Sweden). Div. of Nuclear Power Safety

1996-12-01

Results of series of studies on natural convection heat transfer in decay-heated core melt pools which form in a reactor lower plenum during the progression of a core meltdown accident are described. The emphasis is on modelling and prediction of turbulent heat transfer characteristics of natural convection in a liquid pool with an internal energy source. Methods of computational fluid dynamics, including direct numerical simulation, were applied for investigation. Refs, figs, tabs.

Degraded core accidents: review of aerosol behaviour in the containment of a PWR

International Nuclear Information System (INIS)

Nichols, A.L.; Walker, B.C.

1981-09-01

Low probability-high consequence accidents have become an important issue in reactor safety studies. Such accidents would involve damage to the core and the subsequent release of radioactive fission products into the environment. Aerosols play a major role in the transport and removal of these fission products in the reactor building containment. The aerosol mechanisms, computer modelling codes and experimental studies used to predict aerosol behaviour in the containment of a PWR are reviewed. There are significant uncertainties in the aerosol source terms and specific recommendations have been made for further studies, particularly with respect to code development and high density aerosol-fission product transport within closed systems. (author)

Lessons from the Russian meltdown : the economics of soft legal constraints

NARCIS (Netherlands)

Perotti, E.C.

2002-01-01

On 17 August 1998 Russia abandoned its exchange rate regime, defaulted on its domestic public debt and declared a moratorium on banks' foreign liabilities. This was equivalent to an outright default. The depth and speed of the Russian meltdown shocked the international markets and precipitated a

Core dynamics of HTR under ATWS and accident conditions

International Nuclear Information System (INIS)

Nabbi, R.

1988-05-01

The systematic classification of the ATWS has been undertaken by analogy to the considerations made for LWR. The initiating events of ATWS and protection actions of safety systems resulting from monitoring of the system variables have been described. The main emphasis of this work is the analysis of the core dynamic consequences of scram failure during the anticipated transients. The investigation has shown that because of the temperature feedback mechanisms a temperature rise during the ATWS results in a self-shutdown of the reactor. Further inherent safety features of the HTR - conditioned by the high heat capacity of the core and by the compressibility of the coolant - do effectively counteract an undesirable increase of temperature and pressure in the primary circuit. In case of the long-term failure of the forced cooling and following core heatup, neutron physical phenomena appear which determine the reactivity behaviour of the HTR. They are, for instance, the decay of Xenon 135, release of the fission products and subsiding of the top reflector. The results of the computer simulations show that a recriticality has to be excluded during the first 2 days if the reactor is shutdown by the reflector rods at the beginning of the accident. (orig./HP) [de

Specific features of RBMK severe accidents progression and approach to the accident management

International Nuclear Information System (INIS)

Vasilevskij, V.P.; Nikitin, Yu.M.; Petrov, A.A.; Potapov, A.A.; Cherkashov, Yu.M.

2001-01-01

Fundamental construction features of the LWGR facilities (absence of common external containment shell, disintegrated circulation circuit and multichannel reactor core, positive vapor reactivity coefficient, high mass of thermally capacious graphite moderator) predetermining development of assumed heavy non-projected accidents and handling them are treated. Rating the categories of the reactor core damages for non-projected accidents and accident types producing specific grope of damages is given. Passing standard non-projected accidents, possible methods of attack accident consequences, as well as methods of calculated analysis of non-projected accidents are demonstrated [ru

Atucha I nuclear power plant: Probabilistic safety study. Loss-of-coolant accidents

International Nuclear Information System (INIS)

Perez, S.S.

1987-01-01

The plant response to the group of events 'large coolant loss' in order to evaluate the associated risk is analyzed. The event that covers all events of similar sequence due to its evolution features, being also the most demanded, is selected as starting event. The representative event is the 'guillotine type rupture of cold primary branch'. An annual occurrence frequency of 10/year is assumed for this event. The safety systems, when the event occurs, must assure the reactor shutdown and the core cooling, creating a heat sink to remove the decay heat. The annual frequency of core meltdown due to great loss of coolant is obtained multiplying the annual frequency of the starting event by the probability of failure of involved safety systems. By means of failure trees, the following is obtained: a) probability of failure to demand of the boron injection shutdown system = 4 x 10 -2 ; b) probability of failure to demand of the high pressure safety injection = 3 x 10 -3 ; c) probability of emergency cooling system failure = 4.4 x 10 -2 . Therefore, the three possible sequences of core meltdown have the following frequencies: λ 1 = 4 x 10 -6 /year λ 2 = 3 x 10 -7 /year λ 3 = 4.4 x 10 -6 /year. (Author)

Safeguarding of emergency core cooling in case of loss-of-coolant accidents with insulation material release

International Nuclear Information System (INIS)

Pointner, W.; Broecker, A.

2012-01-01

The report on safeguarding of emergency core cooling in case of loss-of-coolant accidents with insulation material release covers the following issues: assessment of the relevant status for PWR, evaluation of the national and international (USA, Canada, France) status, actualization of recommendations, transferability from PWR to BWR. Generic studies on the core cooling capability in case of insulation material release in BWR-type reactors were evaluated.

Nuclear reactor core safety device

International Nuclear Information System (INIS)

Colgate, S.A.

1977-01-01

The danger of a steam explosion from a nuclear reactor core melt-down can be greatly reduced by adding a gasifying agent to the fuel that releases a large amount of gas at a predetermined pre-melt-down temperature that ruptures the bottom end of the fuel rod and blows the finely divided fuel into a residual coolant bath at the bottom of the reactor. This residual bath should be equipped with a secondary cooling loop

Physical properties of molten core materials: Zr-Ni and Zr-Cr alloys measured by electrostatic levitation

Energy Technology Data Exchange (ETDEWEB)

Ohishi, Yuji, E-mail: ohishi@see.eng.osaka-u.ac.jp [Graduate School of Engineering, Osaka University (Japan); Kondo, Toshiki [Graduate School of Engineering, Osaka University (Japan); Ishikawa, Takehiko [Japan Aerospace Exploration Agency (Japan); SOKEN-DAI (Graduate University for Advanced Studies) (Japan); Okada, Junpei T. [Institute for Materials Research, Tohoku University (Japan); Watanabe, Yuki [Advanced Engineering Services Co. Ltd. (Japan); Muta, Hiroaki; Kurosaki, Ken [Graduate School of Engineering, Osaka University (Japan); Yamanaka, Shinsuke [Graduate School of Engineering, Osaka University (Japan); Research Institute of Nuclear Engineering, University of Fukui (Japan)

2017-03-15

It is important to understand the behaviors of molten core materials to investigate the progression of a core meltdown accident. In the early stages of bundle degradation, low-melting-temperature liquid phases are expected to form via the eutectic reaction between Zircaloy and stainless steel. The main component of Zircaloy is Zr and those of stainless steel are Fe, Ni, and Cr. Our group has previously reported physical property data such as viscosity, density, and surface tension for Zr-Fe liquid alloys using an electrostatic levitation technique. In this study, we report the viscosity, density, and surface tension of Zr-Ni and Zr-Cr liquid alloys (Zr{sub 1-x}Ni{sub x} (x = 0.12 and 0.24) and Zr{sub 0.77}Cr{sub 0.23}) using the electrostatic levitation technique. - Highlights: • The physical properties of Zr-Ni and Zr-Cr liquid alloys have been measured Zr{sub 1-x}Ni{sub x} (x = 0.12 and 0.24) and Zr{sub 77}Cr{sub 23}. • The measurement was conducted using the electrostatic levitation technique. • The density, viscosity, and surface tension of each liquid alloy were measured.

Physical properties of molten core materials: Zr-Ni and Zr-Cr alloys measured by electrostatic levitation

International Nuclear Information System (INIS)

Ohishi, Yuji; Kondo, Toshiki; Ishikawa, Takehiko; Okada, Junpei T.; Watanabe, Yuki; Muta, Hiroaki; Kurosaki, Ken; Yamanaka, Shinsuke

2017-01-01

It is important to understand the behaviors of molten core materials to investigate the progression of a core meltdown accident. In the early stages of bundle degradation, low-melting-temperature liquid phases are expected to form via the eutectic reaction between Zircaloy and stainless steel. The main component of Zircaloy is Zr and those of stainless steel are Fe, Ni, and Cr. Our group has previously reported physical property data such as viscosity, density, and surface tension for Zr-Fe liquid alloys using an electrostatic levitation technique. In this study, we report the viscosity, density, and surface tension of Zr-Ni and Zr-Cr liquid alloys (Zr 1-x Ni x (x = 0.12 and 0.24) and Zr 0.77 Cr 0.23 ) using the electrostatic levitation technique. - Highlights: • The physical properties of Zr-Ni and Zr-Cr liquid alloys have been measured Zr 1-x Ni x (x = 0.12 and 0.24) and Zr 77 Cr 23 . • The measurement was conducted using the electrostatic levitation technique. • The density, viscosity, and surface tension of each liquid alloy were measured.

Comparison of the behaviour of two core designs for ASTRID in case of severe accidents

Energy Technology Data Exchange (ETDEWEB)

Bertrand, F., E-mail: frederic.bertrand@cea.fr [CEA, DEN, DER, F-13108 Saint Paul-lez-Durance (France); Marie, N.; Prulhière, G.; Lecerf, J. [CEA, DEN, DER, F-13108 Saint Paul-lez-Durance (France); Seiler, J.M. [CEA, DEN, DTN, F-38054 Grenoble (France)

2016-02-15

Highlights: • Low void worth CFV and SFRv2 cores are compared for ASTRID pre-conceptual design. • Severe accident behaviour is assessed with a simplified calculation approach and tools. • Mitigation to limit reactivity inserted by core compaction is easier for CFV than for SFRv2 core. • When facing arbitrary reactivity ramps, CFV core would lead to lower energy release than SFRv2 core. • Time scale for core degradation is one order of magnitude larger for CFV than for SFRv2. - Abstract: The present paper is dedicated to the studies carried out during the first stage of the pre-conceptual design of the French demonstrator of fourth generation SFR reactors (ASTRID) in order to compare the behaviour of two envisaged core concepts under severe accident transients. Among the two studied core concepts, whose powers are 1500 MWth, the first one is a classical homogeneous core (called SFRv2) with large pin diameter whose the sodium overall voiding reactivity effect is 5 $. The second concept is an axially heterogeneous core (called CFV) whose global void reactivity effect is negative (−1.2 $ at the end of cycle at the equilibrium). The comparison of the cores relies on two typical accident families: a reactivity insertion (unprotected transient overpower, UTOP) and an overall loss of core cooling (unprotected loss of flow, ULOF). In the first part of the comparison, the primary phase of an UTOP is studied in order to assess typical features of the transient behaviour: power and reactivity evolutions, material heating and melting/vaporization and mechanical energy release due to fuel vapor expansion. The second part of the comparison deals with the calculation of the reactivity potential for degraded states (molten pools) representative of the secondary phase of a mild UTOP and of a strong UTOP (strong or mild qualifies the reactivity ramp inserted). According to the reactivity potential, the amount of fuel to extract from the core and the amount of absorber

Reactivity Accidents in CAREM-25 Core with and Without Safety Systems Actuation

International Nuclear Information System (INIS)

Gimenez, Marcelo; Vertullo, Alicia; Schlamp, Miguel

2000-01-01

A reactivity accident in CAREM core can be provoked by different initiating events, a cold water injection in pressure vessel, a secondary side steam line breakage and a failure in the absorbing rods drive system.The present work analyses inadverted control rod withdraws transients.Maximum worth control rod (2.5 $) at normal velocity (1 cm/s) is adopted for the simulations (Reactivity ramp of 0.018 $/s).Different scenarios considering actuation of first shutdown system (FSS), second shutdown system (SSS) and selflimiting conditions were modeled.Results of the accident with actuation of FSS show that safety margins are well above critical values (DNBR and CPR).In the cases with failure of the FSS and success of SSS or selflimited, safety margins are below critical values, however, the SSS provides a reduction of elapsed time under advised margins

Flowing and freezing of molten core materials during unprotected loss of flow accidents in sodium cooled fast reactors

International Nuclear Information System (INIS)

Maschek, W.; Royl, P.

1988-09-01

Flowing and freezing of mobile core materials change the fissile material distribution and core-inventory under hypothetical accident conditions and determine the path to permanent shutdown of the neutronic events and the energetic potentials. The report classifies the bondary conditions for such flowing and freezing processes by going through the different situations under which these processes can occur in the scenario of the unprotected loss of flow (ULOF) accident. The classification is based on ULOF-accident simulations for a homogeneous reactor core concept of a 300 MWe LMFBR (e. g. SNR-300), but many boundary conditions are also characteristic for other core designs. A review of the relevant experiments is then made to correlate the available experimental information with these classified boundary conditions and to look at the resulting flowing and freezing processes. Boundary conditions that have been experimentally shown to be important are assigned high priorities. The data are specifically valued in relation to these boundary conditions of high priorities. The review includes the major experimental programs with published results. The discussion shows that the results from most clean condition tests for melt relocations are valuable for a better understanding of basic phenomena and analytical model development, but are not directly applicable to real accident conditions. The database for relevant boundary conditions from the ULOF scenario is limited and largely included in integral sequence tests from which quantitative information for modelling is difficult to obtain. Needs for additional investigations are identified. The suggestions are mainly restricted to investigations of the early phase of fuel removal. They are given with reference to candidate facilities and include relocations in the subassemblies and in the inter-subassembly gaps. Particular emphasis is put on the leading edge properties and possible driving forces to which more attention

In-vessel core degradation in LWR severe accidents: a state of the art report to CSNI january 1991

International Nuclear Information System (INIS)

1991-11-01

This state of the art report on in-vessel core degradation has been produced at the request of CSNI Principal Working Group 2. The objective of the report is to present to CSNI member countries the status of research and related information on in-vessel degraded core behaviour in both Pressurised Water Reactors (PWR) and Boiling Water Reactors (BWR). Information on experiments, codes and comparisons of calculations with experiments up to january 1991 is summarised and reviewed. Integrated codes, which are wider in scope than just in-vessel degradation are covered as well as specialist, degraded core codes. Implications for PWR and BWR plant calculations are considered. Conclusions and recommendations for research, plant calculations and further CSNI activity in this area are the subject of the final chapter. A major conclusion of the report is that early phase core degradation is relatively well understood. However, codes need further development to bring them up to date with the experimental database, particularly to include low temperature liquefaction processes. These processes significantly affect early phase core degradation and their neglect could affect assessments of accident management actions (including recriticality in BWR severe accidents)

Analysis of the loss of coolant accident for LEU cores of Pakistan research reactor-1

International Nuclear Information System (INIS)

Khan, L.A.; Bokhari, I.H.; Raza, S.H.

1993-12-01

Response of LEU cores for PARR-1 to a Loss of Coolant Accident (LOCA) has been studied. It has been assumed that pool water drains out to double ended rupture of primary coolant pipe or complete shearing of an experimental beam tube. Results show that for an operating power level of 10 MW, both the first high power and equilibrium cores would enter into melting conditions if the pool drain time is less than 22 h and 11 h respectively. However, an Emergency Core Cooling System (ECCS) capable of spraying the core at flow rate of 8.3 m/sup 3/h, for the above mentioned duration, would keep the peak core temperature much below the critical value. Maximum operating power levels below which melting would not occur have been assessed to 3.4 MW and 4.8 MW, respectively, for the first high power and equilibrium cores. (author) 5 figs

Heat Transfer Analysis of the European Pressurized Water Reactor (EPR) Core Catcher Test Facility Volley

Energy Technology Data Exchange (ETDEWEB)

Pikkarainen, Mika; Laine, Jani; Purhonen, Heikki; Kyrki-Rajamaeki, Riitta [Lappeenranta University of Technology, P.O. 20 53851 Lappeenranta (Finland); Sairanen, Risto [Radiation and Nuclear Safety Authority, P.O. 14 00881 Helsinki (Finland)

2008-07-01

The EPR is designed to cope with severe accidents, involving core meltdown. A specific melt spreading area has been designed within the containment. This core catcher will be flooded by water, which transfers the decay heat to the containment heat removal system. To improve cooling, horizontal flow channels made of cast iron are located also below the core catcher. STUK, the radiation and nuclear safety authority in Finland, wanted an independent study of the functionality of the core catcher design. Effect of the presence of insulation material and boric acid in the cooling water was to be studied, as well as the general behavior of the system in different phases of the flooding of the core melt spreading area. To verify the function of the core catcher design, a scaled down test facility was built at Lappeenranta University of Technology. Since there are some physical restrictions of a test facility computational tools were applied especially for the tests where steady state conditions could not be reached without endangering the integrity of the test facility. This paper introduces the Volley test facility, computational simulations and compares them with the test results. Simulated temperatures of those Volley tests, which could be run until steady state conditions, are very close to the measured temperatures. It can be concluded also, that the temperatures are evidently below the cast iron melting point with heat fluxes used in the tests, if there is a small flow inside the cooling channels or even in case when only a few adjacent cooling channels are totally dry. (authors)

Heat Transfer Analysis of the European Pressurized Water Reactor (EPR) Core Catcher Test Facility Volley

International Nuclear Information System (INIS)

Pikkarainen, Mika; Laine, Jani; Purhonen, Heikki; Kyrki-Rajamaeki, Riitta; Sairanen, Risto

2008-01-01

The EPR is designed to cope with severe accidents, involving core meltdown. A specific melt spreading area has been designed within the containment. This core catcher will be flooded by water, which transfers the decay heat to the containment heat removal system. To improve cooling, horizontal flow channels made of cast iron are located also below the core catcher. STUK, the radiation and nuclear safety authority in Finland, wanted an independent study of the functionality of the core catcher design. Effect of the presence of insulation material and boric acid in the cooling water was to be studied, as well as the general behavior of the system in different phases of the flooding of the core melt spreading area. To verify the function of the core catcher design, a scaled down test facility was built at Lappeenranta University of Technology. Since there are some physical restrictions of a test facility computational tools were applied especially for the tests where steady state conditions could not be reached without endangering the integrity of the test facility. This paper introduces the Volley test facility, computational simulations and compares them with the test results. Simulated temperatures of those Volley tests, which could be run until steady state conditions, are very close to the measured temperatures. It can be concluded also, that the temperatures are evidently below the cast iron melting point with heat fluxes used in the tests, if there is a small flow inside the cooling channels or even in case when only a few adjacent cooling channels are totally dry. (authors)

Comparative analysis of a hypothetical 0.1 $/SEC transient overpower accident in an irradiated LMFBR core using different computer models

International Nuclear Information System (INIS)

Cacciabue, P.C.; Fremont, R. de; Renard, A.

1982-01-01

The Report gives the results of comparative calculations performed by the Whole Core Accident Codes Group which is a subgroup of the Safety Working Group of the Fast Reactor Coordinating Committee for a hypothetical transient overpower accident in an irradiated LMFBR core. Different computer codes from members of the European Community and the United States were used. The calculations are based on a Benchmark problem, using commonly agreed input data for the most important phenomena, such as the fuel pin failure threshold, FCl parameters, etc. Beside this, results with alternative assumptions for theoretical modelling are presented with the scope to show in a parametric way the influence of more advanced modelling capabilities and/or better (so-called best estimate) input data for the most important phenomena on the accident sequences

The acute effects of the thermogenic supplement Meltdown on energy expenditure, fat oxidation, and hemodynamic responses in young, healthy males

Directory of Open Access Journals (Sweden)

Cooke Matt

2008-12-01

Full Text Available Abstract The purpose of this study was to evaluate the effects of a thermogenic supplement, Meltdown, on energy expenditure, fat oxidation, and hemodynamics before and after maximal treadmill exercise. In a double-blind, randomized, placebo-controlled, cross-over design, 12 male participants underwent two testing sessions after consuming either the Meltdown or placebo supplement. While in a fasted state, participants rested for one hour, orally ingested either Meltdown or placebo and rested for another hour, performed a maximal treadmill exercise test, and then rested for another hour. Throughout the testing protocol, resting energy expenditure (REE and respiratory exchange ratio (RER were assessed. In addition, heart rate (HR and blood pressure (BP were assessed before and after exercise. Meltdown increased REE significantly more than placebo at 45 min (1.44 ± 0.25 vs. 1.28 ± 0.23 kcal/min; p = 0.003, 60 min (1.49 ± 0.28 vs. 1.30 ± 0.22 kcal/min; p = 0.025, and 120 min (1.51 ± 0.26 vs. 1.33 ± 0.27 kcals/min; p = 0.014 post-ingestion. Meltdown significantly decreased RER at 30 min (0.84 ± 0.03 vs. 0.91 ± 0.04; p = 0.022 and 45 min post-ingestion (0.82 ± 0.04 vs. 0.89 ± 0.05; p = 0.042, and immediately post-exercise (0.83 ± 0.05 vs. 0.90 ± 0.07; p = 0.009. Furthermore, over the course of the evaluation period, area under the curve assessment demonstrated that REE was significantly increased with Meltdown compared to placebo (992.5 ± 133.1 vs. 895.1 ± 296.1 kcals; p = 0.043, while RER was significantly less than placebo (5.55 ± 0.61 vs. 5.89 ± 0.44; p = 0.002 following ingestion. HR and BP were not significantly affected prior to exercise with either supplement (p > 0.05 and the exercise-induced increases for HR and BP decreased into recovery and were not different between supplements (p > 0.05. These data suggest that Meltdown enhances REE and fat oxidation more than placebo for several hours after ingestion in fully rested and

An investigation of core liquid level depression in small break loss-of-coolant accidents

International Nuclear Information System (INIS)

Schultz, R.R.; Watkins, J.C.; Motley, F.E.; Stumpf, H.; Chen, Y.S.

1991-08-01

Core liquid level depression can result in partial core dryout and heatup early in a small break loss-of-coolant accident (SBLOCA) transient. Such behavior occurs when steam, trapped in the upper regions of the reactor primary system (between the loop seal and the core inventory), moves coolant out of the core region and uncovers the rod upper elevations. The net result is core liquid level depression. Core liquid level depression and subsequent core heatups are investigated using subscale data from the ROSA-IV Program's 1/48-scale Large Scale Test Facility (LSTF) and the 1/1705-scale Semiscale facility. Both facilities are Westinghouse-type, four-loop, pressurized water reactor simulators. The depression phenomena and factors which influence the minimum core level are described and illustrated using examples from the data. Analyses of the subject experiments, conducted using the TRAC-PF1/MOD1 (Version 12.7) thermal-hydraulic code, are also described and summarized. Finally, the response of a typical Westinghouse four-loop plant (RESAR-3S) was calculated to qualitatively study coal liquid level depression in a full-scale system. 31 refs., 37 figs., 6 tabs

Laser-heating and Radiance Spectrometry for the Study of Nuclear Materials in Conditions Simulating a Nuclear Power Plant Accident.

Science.gov (United States)

Manara, Dario; Soldi, Luca; Mastromarino, Sara; Boboridis, Kostantinos; Robba, Davide; Vlahovic, Luka; Konings, Rudy

2017-12-14

Major and severe accidents have occurred three times in nuclear power plants (NPPs), at Three Mile Island (USA, 1979), Chernobyl (former USSR, 1986) and Fukushima (Japan, 2011). Research on the causes, dynamics, and consequences of these mishaps has been performed in a few laboratories worldwide in the last three decades. Common goals of such research activities are: the prevention of these kinds of accidents, both in existing and potential new nuclear power plants; the minimization of their eventual consequences; and ultimately, a full understanding of the real risks connected with NPPs. At the European Commission Joint Research Centre's Institute for Transuranium Elements, a laser-heating and fast radiance spectro-pyrometry facility is used for the laboratory simulation, on a small scale, of NPP core meltdown, the most common type of severe accident (SA) that can occur in a nuclear reactor as a consequence of a failure of the cooling system. This simulation tool permits fast and effective high-temperature measurements on real nuclear materials, such as plutonium and minor actinide-containing fission fuel samples. In this respect, and in its capability to produce large amount of data concerning materials under extreme conditions, the current experimental approach is certainly unique. For current and future concepts of NPP, example results are presented on the melting behavior of some different types of nuclear fuels: uranium-plutonium oxides, carbides, and nitrides. Results on the high-temperature interaction of oxide fuels with containment materials are also briefly shown.

Thermal and hydraulic behaviour of CANDU cores under severe accident conditions - final report

International Nuclear Information System (INIS)

Rogers, J.T.

1984-06-01

This volume of appendices presents listings and sample runs of the computer codes used in the study of the thermalhydraulic behaviour of CANDU reactor cores during severe loss of coolant accidents. The codes, written in standard FORTRAN, are MODBOIL, to calculate moderator temperatures, pressures and water levels; DEBRIS, to calculate the transient temperature distribution in the debris of calandria and pressure tubes and fuel pellets; MOLTENPOOL, to calculate the temperature history in a pool of molten debris; CONFILM, to calculate the behaviour of a condensing film of vaporized core debris on the calandria wall, and BLDG, to calculate the pressurization of the containment during the expulsion of moderator through pressure relief ducts. In addition there are discussions of the average condensation heat transfer coefficient for vaporized core material on the calandria wall, and of vapor explosions

Advanced neutron source reactor conceptual safety analysis report, three-element-core design: Chapter 15, accident analysis

International Nuclear Information System (INIS)

Chen, N.C.J.; Wendel, M.W.; Yoder, G.L.; Harrington, R.M.

1996-02-01

In order to utilize reduced enrichment fuel, the three-element-core design for the Advanced Neutron Source has been proposed. The proposed core configuration consists of inner, middle, and outer elements, with the middle element offset axially beneath the inner and outer elements, which are axially aligned. The three-element-core RELAP5 model assumes that the reactor hardware is changed only within the core region, so that the loop piping, heat exchangers, and pumps remain as assumed for the two-element-core configuration. To assess the impact of changes in the core region configuration and the thermal-hydraulic steady-state conditions, the safety analysis has been updated. This report gives the safety margins for the loss-of-off-site power and pressure-boundary fault accidents based on the RELAP5 results. AU margins are greater for the three-element-core simulations than those calculated for the two-element core

The risk of extinction - the mutational meltdown or the overpopulation

OpenAIRE

Malarz, K.

2006-01-01

The phase diagrams survival-extinction for the Penna model with parameters: (mutations rate)-(birth rate), (mutation rate)-(harmful mutations threshold), (harmful mutation threshold)-(minimal reproduction age) are presented. The extinction phase may be caused by either mutational meltdown or overpopulation. When the Verhulst factor is responsible for removing only newly born babies and does not act on adults the overpopulation is avoided and only genetic factors may lead to species extinction.

The risk of extinction - the mutational meltdown or the overpopulation.

Science.gov (United States)

Malarz, Krzysztof

2007-04-01

The phase diagrams survival-extinction for the Penna model with parameters: (mutations rate)-(birth rate), (mutation rate)-(harmful mutations threshold), (harmful mutation threshold)-(minimal reproduction age) are presented. The extinction phase may be caused by either mutational meltdown or overpopulation. When the Verhulst factor is responsible for removing only newly born babies and does not act on adults the overpopulation is avoided and only genetic factors may lead to species extinction.

Results of research and development works 1982

International Nuclear Information System (INIS)

1983-02-01

Arranged by main topics of research, the following contributions of the Institute are disposed as follows: 1. Fast Breeder Reactor Project (PSB) 1.1 Nuclear fuels and fuel elements 1.2 Cladding and core structure materials 1.3 Plant structure materials 1.4 Safety investigations 2. Nuclear Safety Project (PNS) 2.1 Fuel element behaviour during accidents 2.2 Core meltdown 3. Reprocessing and Waste Management Project (PWA) 4. Fusion technology (FT) 5. Innovations and new tasks (INNA). (orig./IHOe) [de

Thermal hydraulic features of the TMI accident

International Nuclear Information System (INIS)

Tolman, B.

1985-01-01

The TMI-2 accident resulted in extensive core damage and recent data confirms that the reactor vessel was challenged from molten core materials. A hypothesized TMI accident sencario is presented that consistently explains the TMI data and is also consistent with research findings from independent severe fuel damage experiements. The TMI data will prove useful in confirming our understanding of severe core damage accidents under realistic reactor systems conditions. This understanding will aid in addressing safety and regulatory issues related to severe core damage accidents in light water reactors

Steam explosion - physical foundations and relation to nuclear reactor safety

International Nuclear Information System (INIS)

Schumann, U.

1982-08-01

'Steam explosion' means the sudden evaporation of a fluid by heat exchange with a hotter material. Other terms are 'vapour explosion', 'thermal explosion', and 'energetic fuel-coolant interaction (FCI)'. In such an event a large fraction of the thermal energy initially stored in the hot material may possibly be converted into mechanical work. For pressurized water reactors one discusses (e.g. in risk analysis studies) a core melt-down accident during which molten fuel comes into contact with water. In the analysis of the consequences one has to investigate steam explosions. In this report an overview over the state of the knowledge is given. The overview is based on an extensive literature review. The objective of the report is to provide the basic knowledge which is required for understanding of the most important theories on the process of steam explosions. Following topics are treated: overview on steam explosion incidents, work potential, spontaneous nucleation, concept of detonation, results of some typical experiments, hydrodynamic fragmentation of drops, bubbles and jets, coarse mixtures, film-boiling, scenario of a core melt-down accident with possible steam-explosion in a pressurized water reactor. (orig.) [de

Analysis of reactivity accidents of the RSG-GAS core with silicide fuel

International Nuclear Information System (INIS)

Tukiran

2002-01-01

The fuels of RSG-GAS reactor is changed from uranium oxide to uranium silicide. For time being, the fuel of RSG-GAS core are mixed up between oxide and silicide fuels with 250 gr of loading and 2.96 g U/cm 3 of density, respectively. While, silicide fuel with 300 gr of loading is still under research. The advantages of silicide fuels are can be used in high density, so that, it can be stayed longer in the core at higher burn-up, therefore, the length of cycle is longer. The silicide fuel in RSG-GAS core is used in step-wise by using mixed up core. Firstly, it is used silicide fuel with 250 gr of loading and then, silicide fuel with 300 gr of loading (3.55 g U/cm 3 of density). In every step-wise of fuel loading must be analysed its safety margin. In this occasion, it is analysed the reactivity accident of RSG-GAS core with 300 gr of silicide fuel loading. The calculation was done by using POKDYN code which available at P2TRR. The calculation was done by reactivity insertion at start up and power rangers. From all cases which were have been done, the results of analysis showed that there is no anomaly and safety margin break at RSG-GAS core with 300 gr silicide fuel loading

Research and development with regard to severe accidents in pressurised water reactors: Summary and outlook

International Nuclear Information System (INIS)

2011-01-01

This document reviews the current state of research on severe accidents in France and other countries. It aims to provide an objective vision, and one that's as exhaustive as possible, for this innovative field of research. It will help in identifying R and D requirements and categorising them hierarchically. Obviously, the resulting prioritisation must be completed by a rigorous examination of needs in terms of safety analyses for various risks and physical phenomena, especially in relation to Level 2 Probabilistic Safety Assessments. PSA-2 should be sufficiently advanced so as not to obscure physical phenomena that, if not properly understood, might result in substantial uncertainty. It should be noted that neither the safety analyses nor PSA-2 are presented in this document. This report describes the physical phenomena liable to occur during a severe accident, in the reactor vessel and the containment. It presents accident sequences and methods for limiting impact. The corresponding scenarios are detailed in Chapter 2. Chapter 3 deals with in-vessel accident progression, examining core degradation (3.1), corium behaviour in the lower head (3.2), vessel rupture (3.3) and high-pressure core meltdown (3.4). Chapter 4 focuses on phenomena liable to induce early containment failure, namely direct containment heating (4.1), hydrogen risk (4.2) and steam explosions (4.3). The phenomenon that could lead to a late containment failure, namely molten core-concrete interaction, is discussed in Chapter 5. Chapter 6 focuses on problems related to in-vessel and ex-vessel corium retention and cooling, namely in-vessel retention by flooding the primary circuit or the reactor pit (6.1), cooling of the corium under water during the corium-concrete interaction (6.2), corium spreading (6.3) and ex-vessel core catchers (6.4). Chapter 7 relates to the release and transport of fission products (FP), addressing the themes of in-vessel FP release (7.1) and ex-vessel FP release (7.3), FP

Why Competent Persons Have Meltdowns Working with Troubled Students: A Personal Essay

Science.gov (United States)

Long, Nicholas J.

2010-01-01

How do otherwise competent helpers "lose it" in work with certain troubled children and youth? Drawing on extensive research and practice expertise, this article identifies four causes of these predictable professional "meltdowns"--(1) Caught in the Conflict Cycle; (2) Violation of cherished values and beliefs; (3) Tap-in issues; and (4) Carry-in…

The Accident Analysis Due to Reactivity Insertion of RSG GAS 3.55 g U/cc Silicide Core

International Nuclear Information System (INIS)

Endiah Puji-Hastuti; Surbakti, Tukiran

2004-01-01

The fuels of RSG-GAS reactor was changed from uranium oxide with 250 g U of loading or 2.96 g U/cc of fuel loading to uranium silicide with the same loading. The silicide fuels can be used in higher density, staying longer in the reactor core and hence having a longer cycle length. The silicide fuel in RSG-GAS core was made up in step-wise by using mixed up core Firstly, it was used silicide fuel with 250 g U of loading and then, silicide fuel with 300 g U of loading (3.55 g U/cc of fuel loading). In every step-wise of fuel loading, it must be analyzed its safety margin. In this occasion, the reactivity accident of RSG-GAS core with 300 g U of silicide fuel loading is analyzed. The calculation was done using EUREKA-2/RR code available at P2TRR. The calculation was done by reactivity insertion at start up and power rangers. The worst case accident is transient due to control rod with drawl failure at start up by means of lowest initial power (0.1 W), either in power range. From all cases which have been done, the results of analysis showed that there is no anomaly and safety margin break at RSG-GAS core with 300 g U silicide fuel loading. (author)

Modelling of QUENCH-03 and QUENCH-06 Experiments Using RELAP/SCDAPSIM and ASTEC Codes

Directory of Open Access Journals (Sweden)

Tadas Kaliatka

2014-01-01

Full Text Available To prevent total meltdown of the uncovered and overheated core, the reflooding with water is a necessary accident management measure. Because these actions lead to the generation of hydrogen, which can cause further problems, the related phenomena are investigated performing experiments and computer simulations. In this paper, for the experiments of loss of coolant accidents, performed in Forschungszentrum Karlsruhe, QUENCH-03 and QUENCH-06 are modelled using RELAP5/SCDAPSIM and ASTEC codes. The performed benchmark allowed analysing different modelling features. The recommendations for the model development are presented.

Behavior of a corium jet in high pressure melt ejection from a reactor pressure vessel

International Nuclear Information System (INIS)

Frid, W.E.

1986-01-01

A model has been developed to calculate the expansion and fragmentation of a corium jet, due to the evolution of dissolved gas, during a postulated core meltdown accident. Parametric calculations have been performed for a PWR high pressure accident scenario. Jet breakup occurs within a few jet diameters from the RPV. The diameter of the fragmented jet at the level of the reactor cavity floor is predicted to be 40-130 times the discharge diameter. Particles generated by fragmentation of corium melt are predicted to be in the 30-150 μm size range

Assessment of Core Failure Limits for Light Water Reactor Fuel under Reactivity Initiated Accidents

International Nuclear Information System (INIS)

Jernkvist, Lars Olof; Massih, Ali R.

2004-12-01

Core failure limits for high-burnup light water reactor UO 2 fuel rods, subjected to postulated reactivity initiated accidents (RIAs), are here assessed by use of best-estimate computational methods. The considered RIAs are the hot zero power rod ejection accident (HZP REA) in pressurized water reactors and the cold zero power control rod drop accident (CZP CRDA) in boiling water reactors. Burnup dependent core failure limits for these events are established by calculating the fuel radial average enthalpy connected with incipient fuel pellet melting for fuel burnups in the range of 30 to 70 MWd/kgU. The postulated HZP REA and CZP CRDA result in lower enthalpies for pellet melting than RIAs that take place at rated power. Consequently, the enthalpy thresholds presented here are lower bounds to RIAs at rated power. The calculations are performed with best-estimate models, which are applied in the FRAPCON-3.2 and SCANAIR-3.2 computer codes. Based on the results of three-dimensional core kinetics analyses, the considered power transients are simulated by a Gaussian pulse shape, with a fixed width of either 25 ms (REA) or 45 ms (CRDA). Notwithstanding the differences in postulated accident scenarios between the REA and the CRDA, the calculated core failure limits for these two events are similar. The calculated enthalpy thresholds for fuel pellet melting decrease gradually with fuel burnup, from approximately 960 J/gUO 2 at 30 MWd/kgU to 810 J/gUO 2 at 70 MWd/kgU. The decline is due to depression of the UO 2 melting temperature with increasing burnup, in combination with burnup related changes to the radial power distribution within the fuel pellets. The presented fuel enthalpy thresholds for incipient UO 2 melting provide best-estimate core failure limits for low- and intermediate-burnup fuel. However, pulse reactor tests on high-burnup fuel rods indicate that the accumulation of gaseous fission products within the pellets may lead to fuel dispersal into the coolant at

Thermal and stress analyses of meltdown cups for LMFBR safety experiments using SLSF in-reactor loops

International Nuclear Information System (INIS)

Blomquist, C.A.; Ariman, T.; Pierce, R.D.; Pedersen, D.R.

1977-01-01

A description of a meltdown cup to be used in the SLSF in-reactor experiments is presented. Thermal analyses have shown that the cup is capable of containing and cooling the postulated quantities of molten fuel and steel. The basic loadings for stress analyses were defined and failure modes were determined. It was shown that both the maximum bending stress and maximum tangential stress in the Inconel vessel are below the material yield stress. Additionally, the axial stress in the Inconel vessel was found to be negligible. The shear stress in the wire-formed retaining ring is much below the maximum shear stress. Therefore, the meltdown cup is capable of performing its required function

Aerosol retention during SGTR meltdown sequences under different conditions of tubes vibration

International Nuclear Information System (INIS)

Delgado Tardaguila, R.; Herranz, L. E.

2014-01-01

The containment bypass of the fission products during SGTR meltdown sequences makes this scenario be a significant risk contributor in PWRs. The EU-SGTR, ARTIST 1 and 2 and the on-going ARTIST-extension programs have investigated the potential attenuation of the source term reaching the secondary side of a failed SG even in the absence of water. (Author)

Incorporation of phenomenological uncertainties in probabilistic safety analysis - application to LMFBR core disruptive accident energetics

Energy Technology Data Exchange (ETDEWEB)

Najafi, B; Theofanous, T G; Rumble, E T; Atefi, B

1984-08-01

This report describes a method for quantifying frequency and consequence uncertainty distribution associated with core disruptive accidents (CDAs). The method was developed to estimate the frequency and magnitude of energy impacting the reactor vessel head of the Clinch River Breeder Plant (CRBRP) given the occurrence of hypothetical CDAs. The methodology is illustrated using the CRBR example.

PWR degraded core analysis

International Nuclear Information System (INIS)

Gittus, J.H.

1982-04-01

A review is presented of the various phenomena involved in degraded core accidents and the ensuing transport of fission products from the fuel to the primary circuit and the containment. The dominant accident sequences found in the PWR risk studies published to date are briefly described. Then chapters deal with the following topics: the condition and behaviour of water reactor fuel during normal operation and at the commencement of degraded core accidents; the generation of hydrogen from the Zircaloy-steam and the steel-steam reactions; the way in which the core deforms and finally melts following loss of coolant; debris relocation analysis; containment integrity; fission product behaviour during a degraded core accident. (U.K.)

Severe accident phenomena

International Nuclear Information System (INIS)

Jokiniemi, J.; Kilpi, K.; Lindholm, I.; Maekynen, J.; Pekkarinen, E.; Sairanen, R.; Silde, A.

1995-02-01

Severe accidents are nuclear reactor accidents in which the reactor core is substantially damaged. The report describes severe reactor accident phenomena and their significance for the safety of nuclear power plants. A comprehensive set of phenomena ranging from accident initiation to containment behaviour and containment integrity questions are covered. The report is based on expertise gained in the severe accident assessment projects conducted at the Technical Research Centre of Finland (VTT). (49 refs., 32 figs., 12 tabs.)

Estimation of the mechanical effects of a core disruptive accident on a LMFBR

International Nuclear Information System (INIS)

Robbe, M.F.; Lepareux, M.; Treille, E.

2001-01-01

In case of a Hypothetical Core Disruptive Accident (HCDA) in a Liquid Metal Reactor, the interaction between fuel and liquid sodium creates a high pressure gas bubble in the core. The violent expansion of this bubble loads the vessel and the internal structures, whose deformation is important. In order to demonstrate the CASTEM-PLEXUS capability to predict the behaviour of real reactors], axisymmetric computations of the MARA series were confronted with the experimental results. The computations performed at the beginning of the years 90 showed a rather good agreement between the experimental and computed results for the MARA 8 and MARA 10 tests even if there were some discrepancies which might be eliminated by increasing the fineness of the mesh. On the contrary, the prediction of the MARS structure displacements and strains was overestimated. This conservatism was supposed to come from the fact that several MARS non axisymmetric structures like core elements, pumps and heat exchangers were not represented in the CASTEM-PLEXUS model. These structures, acting as porous barriers, had a protective effect on the containment by absorbing energy and slowing down the fluid impacting the containment. For these reasons, we developed in CASTEM-PLEXUS a new HCDA constitutive law taking into account the presence of the internal structures (without meshing them) by means of an equivalent porosity method and we simulated the MARS test another time with the new HCDA constitutive law. This paper presents the numerical results relative to the structure behaviour during the accident. The results are described through the evolution of several variables versus time: deformed shape of the structures and the mesh, displacements, stresses and plastic strains. (author)

Investigation of activity release during light water reactor core meltdown

International Nuclear Information System (INIS)

Albrecht, H.; Matschoss, V.; Wild, H.

1978-01-01

A test facility was developed for the determination of activity release and of aerosol characteristics under realistic light water reactor core melting conditions. It is composed of a high-frequency induction furnace, a ThO 2 crucible system, and a collection apparatus consisting of membrane and particulate filters. Thirty-gram samples of a representative core material mixture (corium) were melted under air, argon, or steam at 0.8 to 2.2 bar. In air at 2700 0 C, for example, the relative release was 0.4 to 0.7% for iron, chromium, and cobalt and 4 to 11% for tin, antimony, and manganese. Higher release values of 20 to 40% at lower temperatures (2150 0 C, air) were found for selenium, cadmium, tellurium, and cesium. The size distribution of the aerosol particles was trimodal with maxima at diameters of 0.17, 0.30, and 0.73 μm. The result of a qualitative x-ray microanalysis was that the main elements of the melt were contained in each aerosol particle. Further investigations will include larger melt masses and the additional influence of concrete on the release and aerosol behavior

Study of heat removal by natural convection from the internal core catcher in PFBR using water model experiments

International Nuclear Information System (INIS)

Jasmin Sudha, A.; Punitha, G.; Das, S.K.; Lydia, G.; Murthy, S.S.; Malarvizhi, B.; Harvey, J.; Kannan, S.E.

2005-01-01

Full text of publication follows: In the event of a core meltdown accident in a Fast Breeder Reactor, the molten core material settling on the bottom of the main vessel can endanger the structural integrity of the main vessel. In the design of Prototype Fast Breeder Reactor in India, the construction of which is about to commence, a core catcher is provided as the internal core retention device to collect and retain the core debris in a coolable configuration. Heat transfer by natural convection above and below the core catcher plate, in the zone beneath the core support structure is evaluated from water mockup experiments in the 1:4 geometrically scaled setup. These studies were undertaken towards comparison of experimentally measured temperatures at different locations with the numerical results. The core catcher assembly consists of a core catcher plate, a heat shield plate and a chimney. Decay heat from the core debris is simulated by electrical heating of the heat shield plate. An opening is provided in the cover plate to reproduce the situation in the actual accident where the core debris would have breached a part of the core support structure. Experiments were carried out with different heat flux levels prevailing upon the heat shield plate. Temperature monitoring was done at more than 100 locations, distributed both on the solid components and in water. The temperature data was analysed to get the temperature profile at different steady state conditions. Flow visualisation was also carried out using water soluble dye to establish the direction of the convective currents. The captured images show that water flows through the slots provided in the top portion of the chimney in the upward direction as evidenced from the diffusion of dye injected inside the chimney. Both the temperature data and flow visualisation confirm mixing of water through the opening in the core support structure which indicates that natural convection is set up in that zone

Use of PSA and severe accident assessment results for the accident management

International Nuclear Information System (INIS)

Jang, S. H.; Kim, H. G.; Jang, H. S.; Moon, S. K.; Park, J. U.

1993-12-01

The objectives for this study are to investigate the basic principle or methodology which is applicable to accident management, by using the results of PSA and severe accident research, and also facilitate the preparation of accidents management program in the future. This study was performed as follows: derivation of measures for core damage prevention, derivation of measures for accident mitigation, application of computerized tool to assess severe accident management

Use of PSA and severe accident assessment results for the accident management

Energy Technology Data Exchange (ETDEWEB)

Jang, S H; Kim, H G; Jang, H S; Moon, S K; Park, J U [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

1993-12-15

The objectives for this study are to investigate the basic principle or methodology which is applicable to accident management, by using the results of PSA and severe accident research, and also facilitate the preparation of accidents management program in the future. This study was performed as follows: derivation of measures for core damage prevention, derivation of measures for accident mitigation, application of computerized tool to assess severe accident management.

Study On Safety Analysis Of PWR Reactor Core In Transient And Severe Accident Conditions

International Nuclear Information System (INIS)

Le Dai Dien; Hoang Minh Giang; Nguyen Thi Thanh Thuy; Nguyen Thi Tu Oanh; Le Thi Thu; Pham Tuan Nam; Tran Van Trung; Le Van Hong; Vo Thi Huong

2014-01-01

The cooperation research project on the Study on Safety Analysis of PWR Reactor Core in Transient and Severe Accident Conditions between Institute for Nuclear Science and Technology (INST), VINATOM and Korean Atomic Energy Research Institute (KAERI), Korea has been setup to strengthen the capability of researches in nuclear safety not only in mastering the methods and computer codes, but also in qualifying of young researchers in the field of nuclear safety analysis. Through the studies on the using of thermal hydraulics computer codes like RELAP5, COBRA, FLUENT and CFX the thermal hydraulics research group has made progress in the research including problems for safety analysis of APR1400 nuclear reactor, PIRT methodologies and sub-channel analysis. The study of severe accidents has been started by using MELCOR in collaboration with KAERI experts and the training on the fundamental phenomena occurred in postulated severe accident. For Vietnam side, VVER-1000 nuclear reactor is also intensively studied. The design of core catcher, reactor containment and severe accident management are the main tasks concerning VVER technology. The research results are presented in the 9 th National Conference on Mechanics, Ha Noi, December 8-9, 2012, the 10 th National Conference on Nuclear Science and Technology, Vung Tau, August 14-15, 2013, as well as published in the journal of Nuclear Science and Technology, Vietnam Nuclear Society and other journals. The skills and experience from using computer codes like RELAP5, MELCOR, ANSYS and COBRA in nuclear safety analysis are improved with the nuclear reactors APR1400, Westinghouse 4 loop PWR and especially the VVER-1000 chosen for the specific studies. During cooperation research project, man power and capability of Nuclear Safety center of INST have been strengthen. Three masters were graduated, 2 researchers are engaging in Ph.D course at Hanoi University of Science and Technology and University of Science and Technology, Korea

Review of the SIMMER-II analyses of liquid-metal-cooled fast breeder reactor core-disruptive accident fuel escape

International Nuclear Information System (INIS)

DeVault, G.P.; Bell, C.R.

1985-01-01

Early fuel removal from the active core of a liquid-metal-cooled fast breeder reactor undergoing a core-disruptive accident may reduce the potential for large energetics resulting from recriticalities. This paper presents a review of analyses with the SIMMER-II computer program of the effectiveness of possible fuel escape paths. Where possible, how SIMMER-II compares with or is validated against experiments that simulated the escape paths also is discussed

A Parameter Study of Large Fast Reactor Nuclear Explosion Accidents

Energy Technology Data Exchange (ETDEWEB)

Wiesel, J R

1969-02-15

An IBM-code EEM (Explosive Excursion Model) has been developed for calculating the energy releases associated with the explosive disassembly of a large fast reactor following a superprompt critical condition. The assumed failure chain of events and the possible core collapse following a fuel meltdown give the input data and initial conditions, the most important of which is the reactivity insertion rate at the moment of the explosive core disassembly. The dependence of the energy releases on the reactivity insertion rate, the Doppler reactivity feedback, the power form factor and the core size have been studied. The model enables a quick estimation of conservative values of the destructive mechanical energy releases following a nuclear explosion and gives suggestions as to how to reduce or even avoid such excursions.

A Parameter Study of Large Fast Reactor Nuclear Explosion Accidents

International Nuclear Information System (INIS)

Wiesel, J.R.

1969-02-01

An IBM-code EEM (Explosive Excursion Model) has been developed for calculating the energy releases associated with the explosive disassembly of a large fast reactor following a superprompt critical condition. The assumed failure chain of events and the possible core collapse following a fuel meltdown give the input data and initial conditions, the most important of which is the reactivity insertion rate at the moment of the explosive core disassembly. The dependence of the energy releases on the reactivity insertion rate, the Doppler reactivity feedback, the power form factor and the core size have been studied. The model enables a quick estimation of conservative values of the destructive mechanical energy releases following a nuclear explosion and gives suggestions as to how to reduce or even avoid such excursions

Results of laboratory tests on a robust filtration system for PWR containments in the case of a serious accident

International Nuclear Information System (INIS)

L'Homme, A.; Berlin, M.; Beraud, G.

1986-01-01

A study is currently in progress in France on a simple filtration process using sand as a filtration medium which, in the event of a serious accident leading to core meltdown in a pressurized water reactor, will permit controlled and filtered releases from the containment. Laboratory tests on sand filters for aerosols have been conducted. The tests involved the use of columns of sand, 80 cm high and 20 cm in diameter, under conditions which were similar to those inside the containment of a PWR in which a serious accident has occurred. The sand granulometry, the aerosol particle size and the flow rate and steam content of the fluid to be filtered were variable parameters. The results obtained from the experiment showed that as a filtration medium for this simple filter system for reactors a sand obtainable from the Cattenom quarry was most suitable. For this sand the filtration coefficient for aerosols is greater than 10 and the pressure drop is less than 10 4 pascals. Experience has also shown that there is no risk, under the operating conditions envisaged, that the filter will become clogged by aerosols or steam from condensed water or that there will be any major escape of aerosols retained during long-term operation of the filter or caused by the vaporisation of the condensed water. A larger scale experiment is already being carried out. (author)

Fission product release from HTGR fuel under core heatup accident conditions - HTR2008-58160

International Nuclear Information System (INIS)

Verfondern, K.; Nabielek, H.

2008-01-01

Various countries engaged in the development and fabrication of modern fuel for the High Temperature Gas-Cooled Reactor (HTGR) have initiated activities of modeling the fuel and fission product release behavior with the aim of predicting the fuel performance under operating and accidental conditions of future HTGRs. Within the IAEA directed Coordinated Research Project CRP6 on 'Advances in HTGR Fuel Technology Development' active since 2002, the 13 participating Member States have agreed upon benchmark studies on fuel performance during normal operation and under accident conditions. While the former has been completed in the meantime, the focus is now on the extension of the national code developments to become applicable to core heatup accident conditions. These activities are supported by the fact that core heatup simulation experiments have been resumed recently providing new, highly valuable data. Work on accident performance will be - similar to the normal operation benchmark - consisting of three essential parts comprising both code verification that establishes the correspondence of code work with the underlying physical, chemical and mathematical laws, and code validation that establishes reasonable agreement with the existing experimental data base, but including also predictive calculations for future heating tests and/or reactor concepts. The paper will describe the cases to be studied and the calculational results obtained with the German computer model FRESCO. Among the benchmark cases in consideration are tests which were most recently conducted in the new heating facility KUEFA. Therefore this study will also re-open the discussion and analysis of both the validity of diffusion models and the transport data of the principal fission product species in the HTGR fuel materials as essential input data for the codes. (authors)

In-core fuel disruption experiments simulating LOF accidents for homogeneous and heterogeneous core LMFBRs: FD2/4 series

International Nuclear Information System (INIS)

Wright, S.A.; Mast, P.K.; Schumacher, Gustav; Fischer, E.A.

1982-01-01

A series of Fuel Disruption (FD) experiments simulating LOF accidents transients for homogeneous- and heterogeneous-core LMFBRs is currently being performed in the Annular Core Research Reactor at SNL. The test fuel is observed with high-speed cinematography to determine the timing and the mode of the fuel disruption. The five experiments performed to date show that the timing and mode of fuel disruption depend on the power level, fuel temperature (after preheat and at disruption), and the fuel temperature gradient. Two basic modes of fuel disruption were observed; solid-state disruption and liquid-state swelling followed by slumping. Solid-state dispersive fuel behavior (several hundred degrees prior to fuel melting) is only observed at high power levels (6P 0 ), low preheat temperatures (2000 K), and high thermal gradients (2800 K/mm). The swelling/slumping behavior was observed in all cases near the time of fuel melting. Computational models have been developed that predict the fuel disruption modes and timing observed in the experiments

On high-temperature reactor accident topology

International Nuclear Information System (INIS)

Fassbender, J.; Kroeger, W.; Wolters, J.

1981-01-01

American and German risk studies for an HTGR and independent investigations of hypothetical accident sequences led to a fundamental understanding of the topology of HTGR accident sequences. The dominating importance of core heat-up accidents was confirmed and the initiating events were identified. Complications of core heat-up accidents by air or water ingress are of minor importance for the risk, whereas the long-term development of accidents during days and weeks plays an important role for the environmental impact. The risk caused by an HTGR at a German site cannot yet be determined exactly, because no modern German HTGR design has passed a licensing procedure. Cautious estimates show that risk will appear to be substantially smaller than the LWR risk. The main reasons are the considerably reduced release of fission procucts and the slow development of core heat-up accidents leaving much time for measures which reduce the risk. (orig.) [de

Reactor safety study. An assessment of accident risks in U.S. commercial nuclear power plants. Appendix I. Accident definition and use of event trees

International Nuclear Information System (INIS)

1975-10-01

Information is presented concerning accident definition and use of event trees, event tree methodology, potential accidents covered by the reactor safety study, analysis of potential accidents involving the reactor core, and analysis of potential accidents not involving the core

Response of an ESBWR to an accident like Fukushima

International Nuclear Information System (INIS)

Pena G, C. A.; Salazar S, E.

2014-10-01

The Fukushima nuclear accident occurred on March 11, 2011 was caused by an earthquake measuring 9.0 on the seismic scale, damaging the nuclear power plant (NPP) containing 6 nuclear reactors of boiling water, some of whom suffered a meltdown due to failure in the cooling systems of these. Electrical wiring was damaged and emergency diesel generators stopped with the arrival of the tsunami, caused by the earthquake. The presence of many critical systems in flood areas provided that a cascade of technological failures occurred, culminating in the complete loss of control over the central and reactors. This had important political consequences and several countries have revised their nuclear programs, considering dangerous and unworkable to the nuclear energy to meet the specific energy needs of each country. However, progress in the design of new reactors raise the possibility of continuing to use nuclear energy for much safer than before. The NPP of Fukushima contained BWR reactors of the first commercial generation designed in the 50. The new passive safety systems raise the idea of simplifying the systems, lowering costs while they are safer systems. New designs meet a these needs in both BWRs and PWRs. In this paper the response of an ESBWR reactor to similar conditions to those suffered by the reactors of Fukushima NPP during the accident is analyzed. In this new reactor of III + generation, the recirculation pumps are removed and emergency cooling systems that can maintain the stable core for several hours without electricity are used. To analyze the responses of this new reactor the simulator with basic principles that IAEA makes available to from Member States was used to better understand and analyze the performance of this type of reactors. (Author)

Modular Accident Analysis Program (MAAP) - MELCOR Crosswalk: Phase II Analyzing a Partially Recovered Accident Scenario

Energy Technology Data Exchange (ETDEWEB)

Andrews, Nathan [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Faucett, Christopher [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Haskin, Troy Christopher [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Luxat, Dave [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Geiger, Garrett [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Codella, Brittany [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-10-01

Following the conclusion of the first phase of the crosswalk analysis, one of the key unanswered questions was whether or not the deviations found would persist during a partially recovered accident scenario, similar to the one that occurred in TMI - 2. In particular this analysis aims to compare the impact of core degradation morphology on quenching models inherent within the two codes and the coolability of debris during partially recovered accidents. A primary motivation for this study is the development of insights into how uncertainties in core damage progression models impact the ability to assess the potential for recovery of a degraded core. These quench and core recovery models are of the most interest when there is a significant amount of core damage, but intact and degraded fuel still remain in the cor e region or the lower plenum. Accordingly this analysis presents a spectrum of partially recovered accident scenarios by varying both water injection timing and rate to highlight the impact of core degradation phenomena on recovered accident scenarios. This analysis uses the newly released MELCOR 2.2 rev. 966 5 and MAAP5, Version 5.04. These code versions, which incorporate a significant number of modifications that have been driven by analyses and forensic evidence obtained from the Fukushima - Daiichi reactor site.

Concluding colloquium of the Nuclear Safety Project (PNS)

International Nuclear Information System (INIS)

1986-08-01

The main points of the report are: environmental loads due to nuclear power stations and fuel reprocessing plants, behaviour of the system during reactor faults, extent of damage for the largest hypothetical reactor accidents and its dependence on time, assessment of the consequences of large hypothetical accidents and safety-related assessment of nuclear plants. The contributions relate particularly to the dynamic stresses on reactor components, behaviour of fuel elements in accidents, core melt-down accidents in LWR's and retention, behaviour and effects of released radionuclides from nuclear plants. Up-dating contributions concern the course, the effects and the analysis of the Chernobyl reactor accident. One contribution each is concerned with the development of waste air filters, the soil/plant transfer of actinides and the description of an FDWR. (DG) [de

Measures for removing hydrogen

International Nuclear Information System (INIS)

Baukal, W.; Koehling, A.; Langer, G.; Poeschel, E.

1984-01-01

Basis for the investigation is a 1300-MW-PWR. The evolution of hydrogen was studied in design-basis and three hypothetical accident scenarios, the loss-of-coolant accident, the failure of emergency cooling system and core meltdown. It was shown that in the case of release rates of 4m 3 H 2 /h, the known post-accident hydrogen removal systems can be used and at medium rates up to 80 m 3 H 2 /h recombines of nuclear and non-nuclear industries are suitable under certain conditions. In the case of larger release rates it appears useful to apply a small recombiner of the type of the post-accident hydrogen removal system combined with an other hydrogen countermeasures. Recommendations are being made for the installation of an accident-proof hydrogen measuring system. (DG) [de

Source term and behavioural parameters for a postulated HIFAR loss-of-coolant accident

International Nuclear Information System (INIS)

May, F.G.

1987-01-01

The fraction of the fission product inventory which might be released into the atmosphere of the HIFAR reactor containment building (RCB) during a postulated loss-of-coolant accident (LOCA) has been evaluated as a function of time, for each classification of airborne radioactivity. This appraisal will be used as the source term for a computer program, which uses realistic attenuation of the fission product aerosol in a single compartment model with a defined leakrate to predict possible radioactive releases into the environment in a hypothetical bounding case reactor accident which is rather more severe in all major aspects than any single LOCA. Also given are the parameters governing the attenuation of the aerosol and vapours in the atmosphere of the RCB so that their behaviour may be accurately modelled. The source terms for several other types of accident involving the meltdown of fuel elements have also been considered but in less detail than the LOCA case. In some of the cases, the fission products are released directly to atmosphere, so there is no attenuation of the release by deposition within the RCB

The influence of chemistry on core melt accidents

International Nuclear Information System (INIS)

Liljenzin, J.O.

1990-01-01

Chemical reactions play an important role in assessing the safety of nuclear power plants. The main source of heat in the early stage of an accident is due to a chemical reaction between steam and the circonium encapsulating the nuclear fuel. The heating and melting of fuel leads to a release of fission products which rapidly condense to form particles suspended in the surrounding gas. These aerosols are the main carriers of radioactivity as they may transport active material from the reactor vessel into the reactor containment building where it is deposited. The content of fission products in the aerosol particles and their chemical form determine their interaction with water molecules. Chemical forces laed to an absorption of water in the particles which transforms them into droplets with increased mass. The particles become spherical and hence deposit more rapidly on surrounding surfaces. There is a rapid reaction between boron carbide and stainless steel in the control blades of boiling water reactors. There is only a small formation of boric acid. This leads to a smaller formation of volatile iodine compounds. But the alloying process is likely to cause melting of the control blades so the are removed from the reactor core, a process which may have negative secondary effects. It has been found that a series of materials that are present in the reactor containment are likely to participate in various chemical reactions during an accident. Among these are electric cables, motors, thermal insulation, surface coatings and sheet metal. Metallic surface coatings and sheet metal can be some of the main sources of hydrogen. Effects from chemical reactions can be more accurately predicted by the new SHMAPP code, developed within this project, combining thermal, hydraulic and chemical phenomena. (AB)

Analysis of the accident at Fukushima Daiichi nuclear power plant in an A BWR reactor

International Nuclear Information System (INIS)

Escorcia O, D.; Salazar S, E.

2016-09-01

The present work aims to recreate the accident occurred at the Fukushima Daiichi nuclear power plant in Japan on March 11, 2011, making use of an academic simulator of forced circulation of the A BWR reactor provided by the IAEA to know the scope of this simulator. The simulator was developed and distributed by the IAEA for academic purposes and contains the characteristics and general elements of this reactor to be able to simulate transients and failures of different types, allowing also to observe the general behavior of the reactor, as well as several phenomena and present systems in the same. Is an educational tool of great value, but it does not have a scope that allows the training of plant operators. To recreate the conditions of the Fukushima accident in the simulator, we first have to know what events led to this accident, as well as the actions taken by operators and managers to reduce the consequences of this accident; and the sequence of events that occurred during the course of the accident. Differences in the nuclear power plant behavior are observed and interpreted throughout the simulation, since the Fukushima plant technology and the simulator technology are not the same, although they have several elements in common. The Fukushima plant had an event that by far exceeded the design basis, which triggered in an accident that occurred in the first place by a total loss of power supply, followed by the loss of cooling systems, causing a level too high in temperature, melting the core and damaging the containment accordingly, allowing the escape of hydrogen and radioactive material. As a result of the simulation, was determined that the scope of the IAEA academic simulator reaches the entrance of the emergency equipment, so is able to simulate almost all the events occurred at the time of the earthquake and the arrival of the tsunami in the nuclear power plant of Fukushima Daiichi. However, due to its characteristics, is not able to simulate later

A synopsis of experimental activities on small-break LOCA

International Nuclear Information System (INIS)

Hein, D.

1984-01-01

Through reactor safety studies like WASH 1400 or the ''Deutsche Risiko-Studie'' the attention has turned from large break loss of coolant accidents to small breaks because of the high contribution of this type of accidents to core meltdown. But only after the TMI-2 accident were also the main activities in the experimental fields shifted world-wide to the small break LOCAs. Since TMI numerous research programs have either been finished or are underway. This review paper presents: a classification of the various types of transients according to break size; a discussion of major physical phenomena associated with a small break LOCA, and a description of a few selected research programs and the most important results achieved. (author)

Severe accident tests and development of domestic severe accident system codes

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

According to lessons learned from Fukushima-Daiichi NPS accidents, the safety evaluation will be started based on the NRA's New Safety Standards. In parallel with this movement, reinforcement of Severe Accident (SA) Measures and Accident Managements (AMs) has been undertaken and establishments of relevant regulations and standards are recognized as urgent subjects. Strengthening responses against nuclear plant hazards, as well as realistic protection measures and their standardization is also recognized as urgent subjects. Furthermore, decommissioning of Fukushima-Daiichi Unit1 through Unit4 is promoted diligently. Taking into account JNES's mission with regard to these SA Measures, AMs and decommissioning, movement of improving SA evaluation methodologies inside and outside Japan, and prioritization of subjects based on analyses of sequences of Fukushima-Daiichi NPS accidents, three viewpoints was extracted. These viewpoints were substantiated as the following three groups of R and D subjects: (1) Obtaining near term experimental subjects: Containment venting, Seawater injection, Iodine behaviors. (2) Obtaining mid and long experimental subjects: Fuel damage behavior at early phase of core degradation, Core melting and debris formation. (3) Development of a macroscopic level SA code for plant system behaviors and a mechanistic level code for core melting and debris formation. (author)

Severe accident tests and development of domestic severe accident system codes

International Nuclear Information System (INIS)

2013-01-01

According to lessons learned from Fukushima-Daiichi NPS accidents, the safety evaluation will be started based on the NRA's New Safety Standards. In parallel with this movement, reinforcement of Severe Accident (SA) Measures and Accident Managements (AMs) has been undertaken and establishments of relevant regulations and standards are recognized as urgent subjects. Strengthening responses against nuclear plant hazards, as well as realistic protection measures and their standardization is also recognized as urgent subjects. Furthermore, decommissioning of Fukushima-Daiichi Unit1 through Unit4 is promoted diligently. Taking into account JNES's mission with regard to these SA Measures, AMs and decommissioning, movement of improving SA evaluation methodologies inside and outside Japan, and prioritization of subjects based on analyses of sequences of Fukushima-Daiichi NPS accidents, three viewpoints was extracted. These viewpoints were substantiated as the following three groups of R and D subjects: (1) Obtaining near term experimental subjects: Containment venting, Seawater injection, Iodine behaviors. (2) Obtaining mid and long experimental subjects: Fuel damage behavior at early phase of core degradation, Core melting and debris formation. (3) Development of a macroscopic level SA code for plant system behaviors and a mechanistic level code for core melting and debris formation. (author)

SEVERE ACCIDENT ISSUES RAISED BY THE FUKUSHIMA ACCIDENT AND IMPROVEMENTS SUGGESTED

OpenAIRE

SONG, JIN HO; KIM, TAE WOON

2014-01-01

This paper revisits the Fukushima accident to draw lessons in the aspect of nuclear safety considering the fact that the Fukushima accident resulted in core damage for three nuclear power plants simultaneously and that there is a high possibility of a failure of the integrity of reactor vessel and primary containment vessel. A brief review on the accident progression at Fukushima nuclear power plants is discussed to highlight the nature and characteristic of the event. As the severe accide...

An assessment of the radiological consequences of releases to groundwater following a core-melt accident at the Sizewell PWR

International Nuclear Information System (INIS)

Maul, P.R.

1984-03-01

In the extremely unlikely event of a degraded core accident at the proposed Sizewell PWR it is theoretically possible for the core to melt through the containment, after which activity could enter groundwater directly or as a result of subsequent leaching of the core in the ground. The radiological consequences of such an event are analysed and compared with the analysis undertaken by the NRPB for the corresponding releases to atmosphere. It is concluded that the risks associated with the groundwater route are much less important than those associated with the atmospheric route. The much longer transport times in the ground compared with those in the atmosphere enable countermeasures to be taken, if necessary, to restrict doses to members of the public to very low levels in the first few years following the accident. The entry of long-lived radionuclides into the sea over very long timescales results in the largest contribution to population doses, but these are delivered at extremely low dose rates which would be negligible compared with background exposure. (author)

Accident progression event tree analysis for postulated severe accidents at N Reactor

International Nuclear Information System (INIS)

Wyss, G.D.; Camp, A.L.; Miller, L.A.; Dingman, S.E.; Kunsman, D.M.; Medford, G.T.

1990-06-01

A Level II/III probabilistic risk assessment (PRA) has been performed for N Reactor, a Department of Energy (DOE) production reactor located on the Hanford reservation in Washington. The accident progression analysis documented in this report determines how core damage accidents identified in the Level I PRA progress from fuel damage to confinement response and potential releases the environment. The objectives of the study are to generate accident progression data for the Level II/III PRA source term model and to identify changes that could improve plant response under accident conditions. The scope of the analysis is comprehensive, excluding only sabotage and operator errors of commission. State-of-the-art methodology is employed based largely on the methods developed by Sandia for the US Nuclear Regulatory Commission in support of the NUREG-1150 study. The accident progression model allows complex interactions and dependencies between systems to be explicitly considered. Latin Hypecube sampling was used to assess the phenomenological and systemic uncertainties associated with the primary and confinement system responses to the core damage accident. The results of the analysis show that the N Reactor confinement concept provides significant radiological protection for most of the accident progression pathways studied

Molten Core - Concrete interactions in nuclear accidents. Theory and design of an experimental facility

International Nuclear Information System (INIS)

Sevon, T.

2005-11-01

In a hypothetical severe accident in a nuclear power plant, the molten core of the reactor may flow onto the concrete floor of containment building. This would cause a molten core . concrete interaction (MCCI), in which the heat transfer from the hot melt to the concrete would cause melting of the concrete. In assessing the safety of nuclear reactors, it is important to know the consequences of such an interaction. As background to the subject, this publication includes a description of the core melt stabilization concept of the European Pressurized water Reactor (EPR), which is being built in Olkiluoto in Finland. The publication includes a description of the basic theory of the interaction and the process of spalling or cracking of concrete when it is heated rapidly. A literature survey and some calculations of the physical properties of concrete and corium. concrete mixtures at high temperatures have been conducted. In addition, an equation is derived for conservative calculation of the maximum possible concrete ablation depth. The publication also includes a literature survey of experimental research on the subject of the MCCI and discussion of the results and deficiencies of the experiments. The main result of this work is the general design of an experimental facility to examine the interaction of molten metals and concrete. The main objective of the experiments is to assess the probability of spalling, or cracking, of concrete under pouring of molten material. A program of five experiments has been designed, and pre-test calculations of the experiments have been conducted with MELCOR 1.8.5 accident analysis program and conservative analytic calculations. (orig.)

Radiological consequence analysis for upgradation of Pakistan Research Reactor-1 from 9 to 10 MW

International Nuclear Information System (INIS)

Khan, L.A.; Raza, S.S.

1993-12-01

Radiological consequence analysis has been carried out for upgradation of PARR-I from 9 to 10 MW. A hypothetical loss of coolant accident resulting in core meltdown and release of fission products to the atmosphere has been analyzed. Whole body and thyroid doses have been calculated as a function of time and distance from the containment building. Based on these dose estimates, boundaries of exclusion and low population zones are assessed. (author)

Key Characteristics of Combined Accident including TLOFW accident for PSA Modeling

Energy Technology Data Exchange (ETDEWEB)

Kim, Bo Gyung; Kang, Hyun Gook [KAIST, Daejeon (Korea, Republic of); Yoon, Ho Joon [Khalifa University of Science, Technology and Research, Abu Dhabi (United Arab Emirates)

2015-05-15

The conventional PSA techniques cannot adequately evaluate all events. The conventional PSA models usually focus on single internal events such as DBAs, the external hazards such as fire, seismic. However, the Fukushima accident of Japan in 2011 reveals that very rare event is necessary to be considered in the PSA model to prevent the radioactive release to environment caused by poor treatment based on lack of the information, and to improve the emergency operation procedure. Especially, the results from PSA can be used to decision making for regulators. Moreover, designers can consider the weakness of plant safety based on the quantified results and understand accident sequence based on human actions and system availability. This study is for PSA modeling of combined accidents including total loss of feedwater (TLOFW) accident. The TLOFW accident is a representative accident involving the failure of cooling through secondary side. If the amount of heat transfer is not enough due to the failure of secondary side, the heat will be accumulated to the primary side by continuous core decay heat. Transients with loss of feedwater include total loss of feedwater accident, loss of condenser vacuum accident, and closure of all MSIVs. When residual heat removal by the secondary side is terminated, the safety injection into the RCS with direct primary depressurization would provide alternative heat removal. This operation is called feed and bleed (F and B) operation. Combined accidents including TLOFW accident are very rare event and partially considered in conventional PSA model. Since the necessity of F and B operation is related to plant conditions, the PSA modeling for combined accidents including TLOFW accident is necessary to identify the design and operational vulnerabilities.The PSA is significant to assess the risk of NPPs, and to identify the design and operational vulnerabilities. Even though the combined accident is very rare event, the consequence of combined

Assessment of accident risks in the CRBRP. Volume 2. Appendices

Energy Technology Data Exchange (ETDEWEB)

None

1977-03-01

Appendices to Volume I include core-related accident-sequence definition, CRBRP risk-assessment sequence-probability determinations, failure-probability data, accident scenario evaluation, radioactive material release analysis, ex-core accident analysis, safety philosophy and design features, calculation of reactor accident consequences, sensitivity study, and risk from fires.

Development of a fission product transport module predicting the behavior of radiological materials during sever accidents in a nuclear power plant

Energy Technology Data Exchange (ETDEWEB)

Kang, Hyung Seok; Rhee, Bo Wook; Kim, Dong Ha [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-09-15

Korea Atomic Energy Research Institute is developing a fission product transport module for predicting the behavior of radioactive materials in the primary cooling system of a nuclear power plant as a separate module, which will be connected to a severe accident analysis code, Core Meltdown Progression Accident Simulation Software (COMPASS). This fission product transport (COMPASS-FP) module consists of a fission product release model, an aerosol generation model, and an aerosol transport model. In the fission product release model there are three submodels based on empirical correlations, and they are used to simulate the fission product gases release from the reactor core. In the aerosol generation model, the mass conservation law and Raoult's law are applied to the mixture of vapors and droplets of the fission products in a specified control volume to find the generation of the aerosol droplet. In the aerosol transport model, empirical correlations available from the open literature are used to simulate the aerosol removal processes owing to the gravitational settling, inertia impaction, diffusiophoresis, and thermophoresis. The COMPASS-FP module was validated against Aerosol Behavior Code Validation and Evaluation (ABCOVE-5) test performed by Hanford Engineering Development Laboratory for comparing the prediction and test data. The comparison results assuming a non-spherical aerosol shape for the suspended aerosol mass concentration showed a good agreement with an error range of about ±6%. It was found that the COMPASS-FP module produced the reasonable results of the fission product gases release, the aerosol generation, and the gravitational settling in the aerosol removal processes for ABCOVE-5. However, more validation for other aerosol removal models needs to be performed.

Release of fission and activation products during LWR core meltdown

International Nuclear Information System (INIS)

Albrecht, H.; Matschoss, V.; Wild, H.

1978-01-01

Experiments are described by which activity release fractions and aerosol characteristics were investigated for various core melting conditions. Samples of corium and fissium were heated by induction to temperatures of 2800 0 C under air, argon and steam. Release values are presented for Cr, Mn, Fe, Co, Se, Zr, Mo, Cd, Sn, Sb, Te, J, Cs and U. The deposition behaviour of the released products was found to depend strongly on the volatility and on the gas flow rate. Preliminary results of additional measurements indicate that the size distribution of the aerosol particles is trimodal. (author)

MELCOR Severe Accident Analysis on the SMART Reactor

International Nuclear Information System (INIS)

Kim, Tae Woon; Jin, Young Ho; Kim, Young In; Kim, Keung Koo; Wang, Ziao; Revankar, Shripad

2014-01-01

A severe accident is analyzed for Korea SMR reactor, SMART. Core melt down sequences are analyzed for SMART reactor core using MELCOR version 1.8.5. MELCOR is developed by Sandia National Laboratory for US NRC for the simulation of severe accidents in nuclear power plants. Two cases are simulated here and compared between them; one is the case for core having 3 concentric rings and the other is the case for core having 5 concentric rings. One inch break LOCA scenario is simulated and compared between these two core models. Time sequences for the thermal hydraulic behaviors of RPV and thermal heatup behaviors of reactor core are explained in graphically. Thermal hydraulic behavior such as the change of pressure, level, mass, and temperature of RPV is explained. Thermal heatup behavior of reactor core such as oxidation of cladding, hydrogen generation, core slumping down to lower plenum, and finally creep rupture of PRV lower head is explained. Engineered safety features such as safety injection systems (SIS), and Passive residual heat removal systems (PHRS), etc. are assumed to be not working. One inch break of severe accident is simulated on Korean SMR (SMART) Integral PWR with MELCOR code version 1.8.5. Core melt progression and lower head failure time is very slow compared to other commercial reactors. Simulation on 3 and 5 radial rings core models gives very similar pattern in core cell failure timings. Other various accident scenarios (for example, SBO in Fukushima) will be tried further. Containment behaviors and source term behaviors in severe accident conditions will be analyzed in future

Study on severe accident induced by large break loss of coolant accident for pressureized water reactor

International Nuclear Information System (INIS)

Zhang Longfei; Zhang Dafa; Wang Shaoming

2007-01-01

Using the best estimate computer code SCDAP/RELAP5/MOD3.2 and taking US Westinghouse corporation Surry nuclear power plant as the reference object, a typical three-loop pressurized water reactor severe accident calculation model was established and 25 cm large break loss of coolant accident (LBLOCA) in cold and hot leg of primary loop induced core melt accident was analyzed. The calculated results show that core melt progression is fast and most of the core material melt and relocated to the lower plenum. The lower head of reactor pressure vessel failed at an early time and the cold leg break is more severe than the hot leg break in primary loop during LBLOCA. (authors)

Exploratory study of molten core material/concrete interactions, July 1975--March 1977

International Nuclear Information System (INIS)

Powers, D.A.; Dahlgren, D.A.; Muir, J.F.; Murfin, W.D.

1978-02-01

An experimental study of the interaction between high-temperature molten materials and structural concrete is described. The experimental efforts focused on the interaction of melts of reactor core materials weighing 12 to 200 kg at temperatures 1700 to 2800 0 C with calcareous and basaltic concrete representative of that found in existing light-water nuclear reactors. Observations concerning the rate and mode of melt penetration into concrete, the nature and generation rate of gases liberated during the interaction, and heat transfer from the melt to the concrete are described. Concrete erosion is shown to be primarily a melting process with little contribution from mechanical spallation. Water and carbon dioxide thermally released from the concrete are extensively reduced to hydrogen and carbon monoxide. Heat transfer from the melt to the concrete is shown to be dependent on gas generation rate and crucible geometry. Interpretation of results from the interaction experiments is supported by separate studies of the thermal decomposition of concretes, response of bulk concrete to intense heat fluxes (28 to 280 W/cm 2 ), and heat transfer from molten materials to decomposing solids. The experimental results are compared to assumptions made in previous analytic studies of core meltdown accidents in light-water nuclear reactors. A preliminary computer code, INTER, which models and extrapolates results of the experimental program is described. The code allows estimation of the effect of physical parameters on the nature of the melt/concrete interaction

On the sequence of core-melt accidents: Fission product release, source terms and Chernobyl release

Energy Technology Data Exchange (ETDEWEB)

Albrecht, H

1986-01-01

There is a sketch of our ideas on the course of a core melt-out accident in a PWR. There is then a survey of the most important results on fission product release, which were obtained by experiments on the SASCHA melt-out plant. The 3rd part considers questions which are important for determining source terms for the environment and the last part contains some considerations on radioactivity release from the Chernobyl reactor.

Core to surge-line energy transport in a severe accident scenario

International Nuclear Information System (INIS)

Marzo, M. di; Almenas, K.; Gopalnarayanan, S.

1994-01-01

The analysis of loss of coolant accidents in a nuclear power plant, which progress to the stage where the core is uncovered, poses important safety related questions. One of these concerns the rate of energy transport to metal components of the primary system. An experimental program has been conducted at the Univ. of Maryland test facility which quantifies the rate of energy transfer from an uncovered core in a B ampersand W (once-through type steam generators) plant. SF 6 is used to simulate the natural circulation driving force of the high pressure steam expected at prototypical conditions. A time-dependent scaling methodology is developed to transpose experimental data to prototypical conditions. To achieve this transformation, a nominal fluid temperature increase rate of 1.0 degrees C/s is inferred from available TMI-2 event data. To bracket the range of potential prototypical transient scenarios, temperature ramps of 0.8 degrees C/s and 1.2 degrees C/s are also considered. Repeated tests, covering a range of test facility conditions, lead to estimated failure times at the surge line nozzle of 1.5 to 2 hours after initiation of the natural circulation phase of the transient

Severe fuel damage in steam and helium environments observed in in-reactor experiments

International Nuclear Information System (INIS)

Saito, S.; Shiozawa, S.

1984-01-01

The bahavior of severe fuel damages has been studied in gaseous environments simulating core uncovery accidents in the in-reactor experiments utilizing the NSRR. Two types of cladding relocation modes, azimuthal flow and melt-down, were revealed through the parametric experiments. The azimuthal flow was evident in an oxidizing environment in case of no oxide film break. The melt-down can be categorized into flow-down and move-down, according to the velocity of the melt-down. Cinematographies showed that the flow-down was very fast as water flows down while the move-down appeared to be much slower. The flow-down was possible in an unoxidizing environment, whereas the move-down of molten cladding occured through a crack induced in an oxide film in an oxidizing environment. The criterion of the relocation modes was developed as a function of peak cladding temperature and oxidation condition. It was also found that neither immediate quench nor fuel fracture occurred upon flooding when cladding temperature was about 1800 0 C at water injection. The external mechanical force is needed for fuel fracture. (orig.)

Performance of core exit thermocouple for PWR accident management action in vessel top break LOCA simulation experiment at OECD/NEA ROSA project

International Nuclear Information System (INIS)

Suzuki, Mitsuhiro; Takeda, Takeshi; Nakamura, Hideo

2009-01-01

Presented are experiment results of the Large Scale Test Facility (LSTF) conducted at the Japan Atomic Energy Agency (JAEA) with a focus on core exit thermocouple (CET) performance to detect core overheat during a vessel top break loss-of-coolant accident (LOCA) simulation experiment. The CET temperatures are used to start accident management (AM) action to quickly depressurize steam generator (SG) secondary side in case of core temperature excursion. Test 6-1 is first test of the OECD/NEA ROSA Project started in 2005, simulating withdraw of a control rod drive mechanism penetration nozzle at the vessel top head. The break size is equivalent to 1.9% cold leg break. The AM action was initiated when CET temperature rose up to 623K. There was no reflux water fallback onto the CETs during the core heat-up period. The core overheat, however, was detected with a time delay of about 230s. In addition, a large temperature discrepancy was observed between the CETs and the hottest core region. This paper clarifies the reason of time delay and temperature discrepancy between the CETs and heated core during boil-off including three-dimensional steam flows in the core and core exit. The paper discusses applicability of the LSTF CET performance to pressurized water reactor (PWR) conditions and a possibility of alternative indicators for earlier AM action than in Test 6-1 is studied by using symptom-based plant parameters such as a reactor vessel water level detection. (author)

Precursors to potential severe core damage accidents: 1996. A status report. Volume 25

International Nuclear Information System (INIS)

Belles, R.J.; Cletcher, J.W.; Copinger, D.A.; Muhlheim, M.D.; Dolan, B.W.; Minarick, J.W.

1997-12-01

This report describes the 14 operational events in 1996 that affected 13 commercial light-water reactors and that are considered to be precursors to potential severe core damage accidents. All these events had conditional probabilities of subsequent severe core damage greater than or equal to 1.0 x 10 -6 . These events were identified by first computer-screening the 1996 licensee event reports from commercial light-water reactors to identify those events that could potentially be precursors. Candidate precursors were selected and evaluated in a process similar to that used in previous assessments. Selected events underwent engineering evaluation that identified, analyzed, and documented the precursors. Other events designated by the Nuclear Regulatory Commission (NRC) also underwent a similar evaluation. Finally, documented precursors were submitted for review by licensees and NRC headquarters and regional offices to ensure the plant design and its response to the precursor were correctly characterized. This study is a continuation of earlier work, which evaluated 1969--1995 events. The report discusses the general rationale for this study, the selection and documentation of events as precursors, and the estimation of conditional probabilities of subsequent severe core damage for the events

Precursors to potential severe core damage accidents: 1997 - A status report. Volume 26

International Nuclear Information System (INIS)

Belles, R.J.; Cletcher, J.W.; Copinger, D.A.; Muhlheim, M.D.; Dolan, B.W.; Minarick, J.W.

1998-11-01

This report describes the five operational events in 1997 that affected five commercial light-water reactors (LWRs) and that are considered to be precursors to potential severe core damage accidents. All these events had conditional probabilities of subsequent severe core damage greater than or equal to 1.0 x 10 -6 . These events were identified by first computer-screening the 1997 licensee event reports from commercial LWRs to identify those events that could be precursors. Candidate precursors were selected and evaluated in a process similar to that used in previous assessments. Selected events underwent engineering evaluation that identified, analyzed, and documented the precursors. Other events designated by the Nuclear Regulatory Commission (NRC) also underwent a similar evaluation. Finally, documented precursors were submitted for review by licensees and NRC headquarters to ensure that the plant design and its response to the precursor were correctly characterized. This study is a continuation of earlier work, which evaluated 1969--1996 events. The report discusses the general rationale for this study, the selection and documentation of events as precursors, and the estimation of conditional probabilities of subsequent severe core damage for the events

Analysis of loss of coolant accident and emergency core cooling system

International Nuclear Information System (INIS)

Abe, Kiyoharu; Kobayashi, Kenji; Hayata, Kunihisa; Tasaka, Kanji; Shiba, Masayoshi

1977-01-01

In this paper, the analysis for the performance evaluation of emergency core cooling system is described, which is the safety protection device to the loss of coolant accidents due to the break of primary cooling pipings of light water reactors. In the LOCA analysis for the performance evaluation of ECCS, it must be shown that a reactor core keeps the form which can be cooled with the ECCS in case of LOCA, and the overheat of the core can be prevented. Namely, the shattering of fuel cladding tubes is never to occur, and for the purpose, the maximum temperature of Zircaloy 2 or 4 cladding tubes must be limited to 1200 deg C, and the relative thickness of oxide film must be below 15%. The calculation for determining the temperature of cladding tubes in case of the LOCA in BWRs and PWRs is explained. First, the primary cooling system, the ECCS and the related installations of BWRs and PWRs are outlined. The code systems for LOCA/ECCS analysis are divid ed into several steps, such as blowdown process, reflooding process and heatup calculation. The examples of the sensitivity analysis of the codes are shown. The LOCA experiments carried out so far in Japan and foreign countries and the LOCA analysis of a BWR with RELAP-4J code are described. The guidance for the performance evaluation of ECCS was established in 1975 by the Reactor Safety Deliberation Committee in Japan, and the contents are quoted. (Kako, I.)

The effects of applying silicon carbide coating on core reactivity of pebble-bed HTR in water ingress accident

Energy Technology Data Exchange (ETDEWEB)

Zuhair, S.; Setiadipura, Topan [National Nuclear Energy Agency of Indonesia, Serpong Tagerang Selatan (Indonesia). Center for Nuclear Reactor Technology and Safety; Su' ud, Zaki [Bandung Institute of Technology (Indonesia). Dept. of Physics

2017-03-15

Graphite is used as the moderator, fuel barrier material, and core structure in High Temperature Reactors (HTRs). However, despite its good thermal and mechanical properties below the radiation and high temperatures, it cannot avoid corrosion as a consequence of an accident of water/air ingress. Degradation of graphite as a main HTR material and the formation of dangerous CO gas is a serious problem in HTR safety. One of the several steps that can be adopted to avoid or prevent the corrosion of graphite by the water/air ingress is the application of a thin layer of silicon carbide (SiC) on the surface of the fuel element. This study investigates the effect of applying SiC coating on the fuel surfaces of pebble-bed HTR in water ingress accident from the reactivity points of view. A series of reactivity calculations were done with the Monte Carlo transport code MCNPX and continuous energy nuclear data library ENDF/B-VII at temperature of 1200 K. Three options of UO{sub 2}, PuO{sub 2}, and ThO{sub 2}/UO{sub 2} fuel kernel were considered to obtain the inter comparison of the core reactivity of pebble-bed HTR in conditions of water/air ingress accident. The calculation results indicated that the UO{sub 2}-fueled pebble-bed HTR reactivity was slightly reduced and relatively more decreased when the thickness of the SiC coating increased. The reactivity characteristic of ThO{sub 2}/UO{sub 2}-fueled pebble-bed HTR showed a similar trend to that of UO{sub 2}, but did not show reactivity peak caused by water ingress. In contrast with UO{sub 2}- and ThO{sub 2}-fueled pebble-bed HTR, although the reactivity of PuO{sub 2}-fueled pebble-bed HTR was the lowest, its characteristics showed a very high reactivity peak (0.33 Δk/k) and this introduction of positive reactivity is difficult to control. SiC coating on the surface of the plutonium fuel pebble has no significant impact. From the comparison between reactivity characteristics of uranium, thorium and plutonium cores with 0

Severe accidents at nuclear power plants. Their risk assessment and accident management

International Nuclear Information System (INIS)

Abe, Kiyoharu.

1995-05-01

This document is to explain the severe accident issues. Severe Accidents are defined as accidents which are far beyond the design basis and result in severe damage of the core. Accidents at Three Mild Island in USA and at Chernobyl in former Soviet Union are examples of severe accidents. The causes and progressions of the accidents as well as the actions taken are described. Probabilistic Safety Assessment (PSA) is a method to estimate the risk of severe accidents at nuclear reactors. The methodology for PSA is briefly described and current status on its application to safety related issues is introduced. The acceptability of the risks which inherently accompany every technology is then discussed. Finally, provision of accident management in Japan is introduced, including the description of accident management measures proposed for BWRs and PWRs. (author)

Coupling of 3-D core computational codes and a reactor simulation software for the computation of PWR reactivity accidents induced by thermal-hydraulic transients

International Nuclear Information System (INIS)

Raymond, P.; Caruge, D.; Paik, H.J.

1994-01-01

The French CEA has recently developed a set of new computer codes for reactor physics computations called the Saphir system which includes CRONOS-2, a three-dimensional neutronic code, FLICA-4, a three-dimensional core thermal hydraulic code, and FLICA-S, a primary loops thermal-hydraulic transient computation code, which are coupled and applied to analyze a severe reactivity accident induced by a thermal hydraulic transient: the Steamline Break accident for a pressurized water reactor until soluble boron begins to accumulate in the core. The coupling of these codes has proved to be numerically stable. 15 figs., 7 refs

A theory of modern cultural shifts and meltdowns.

Science.gov (United States)

Hochberg, Michael E

2004-08-07

Many cultural attributes such as adornment, language slang, mannerisms and rituals are thought to have little or no influence on individual survival and reproduction, functioning rather as markers of cultural identity that promote group cohesion. Here, I show that if cultural markers are under weak selection and subject to loss or substitution, then the breakdown of cultural cohesiveness may proceed without stabilizing reactions until many or most of a culture's identifiers are forever lost. This may culminate in a 'cultural meltdown', whereby the culture is caught in a vortex of ever-decreasing membership and insufficient selection against the accumulation of unfamiliar markers. In progressively altering the topology of communication from diffusion to broadcasting, globalization may be both accelerating the erosion of cultural identities and amplifying dominance behaviours above their normal adaptive levels.

Accident termination by element dropout in the GCFR

International Nuclear Information System (INIS)

Torri, A.; Tomkins, J.L.

1976-01-01

Severe loss-of-flow accidents are being investigated for the GCFR in order to assess the risk from those low-probability accidents which lead to a loss of coolable core geometry. Accident mitigating phenomena unique to the GCFR have been identified for the loss of decay heat removal accident. Circumferential assembly duct melting is calculated to occur at the core mid-plane before the fuel within the assembly melts. The GCFR core assemblies are top-mounted and there is clearance between assemblies to accommodate swelling and thermal distortions without interference. No lateral core clamping system is employed and there are no structures in the plenum below the core. Thus it is possible for the lower portion of the individual assemblies, including most of the fuel, to drop to the cavity floor unless interference or bonding between assemblies develops during the accident. Due to the delay in duct corner melting the melt front at the duct mid-flat progresses over about one-half of the core height. The possibility of inter-element bonding by molten duct steel dislocated into the gap between assemblies has been recognized and a test program to verify the duct melting sequence and to investigate the duct dropout is being planned at the Los Alamos Scientific Laboratory

An outline of the interim report of the investigation committee on the accident at Fukushima Nuclear Power Stations

International Nuclear Information System (INIS)

Yoshioka, Hitoshi

2012-01-01

Interim report of the Investigation Committee of the Accident at Fukushima Nuclear Power Stations (NPSs) was published in December 26, 2011. The Japanese cabinet approved ten committee members including the author in May 2011. The committee interviewed more than 400 people over a total of 900 hours of hearings with about 40 staffs consisting of administrative team and three investigation teams of social system, root causes of the accident and countermeasures to prevent damage expansion of the accident. Interim report concluded 'the accident at Fukushima NPSs was caused by failures of every provision against reactor severe accident'. The failures appeared on (1) function of supervisory system for emergency response, (2) Fukushima Daiichi NPSs on-site disaster response especially related with operation of isolation condenser of unit 1 and high-pressure coolant injection system of unit 3, (3) Fukushima Daiichi NPSs off-site disaster response such the government failed to make use of data on the radioactive plumes released from the plant for evacuations, and (4) preparedness against tsunami and severe accident management. Possible worst or best simulation cases were also discussed. With no human support available on-site, workers might not have been able to prevent the meltdowns. Final report was due at the end of July 2012. (T. Tanaka)

Analyzing the BWR rod drop accident in high-burnup cores

International Nuclear Information System (INIS)

Diamond, D.J.; Neymotin, L.; Kohut, P.

1995-01-01

This study was undertaken for the US Nuclear Regulatory Commission to determine the fuel enthalpy during a rod drop accident (RDA) for cores with high burnup fuel. The calculations were done with the RAMONA-4B code which models the core with 3-dimensional neutron kinetics and multiple parallel coolant channels. The calculations were done with a model for a BWR/4 with fuel bundles having burnups up to 30 GWd/t and also with a model with bundle burnups to 60 GWd/t. This paper also discusses potential sources of uncertainty in calculations with high burnup fuel. One source is the ''rim'' effect which is the extra large peaking of the power distribution at the surface of the pellet. This increases the uncertainty in reactor physics and heat conduction models that assume that the energy deposition has a less peaked spatial distribution. Two other sources of uncertainty are the result of the delayed neutron fraction decreasing with burnup and the positive moderator temperature feedback increasing with burnup. Since these effects tend to increase the severity of the event, an RDA calculation for high burnup fuel will underpredict the fuel enthalpy if the effects are not properly taken into account. Other sources of uncertainty that are important come from the initial conditions chosen for the RDA. This includes the initial control rod pattern as well as the initial thermal-hydraulic conditions

Severe Accident Research Program plan update

International Nuclear Information System (INIS)

1992-12-01

In August 1989, the staff published NUREG-1365, ''Revised Severe Accident Research Program Plan.'' Since 1989, significant progress has been made in severe accident research to warrant an update to NUREG-1365. The staff has prepared this SARP Plan Update to: (1) Identify those issues that have been closed or are near completion, (2) Describe the progress in our understanding of important severe accident phenomena, (3) Define the long-term research that is directed at improving our understanding of severe accident phenomena and developing improved methods for assessing core melt progression, direct containment heating, and fuel-coolant interactions, and (4) Reflect the growing emphasis in two additional areas--advanced light water reactors, and support for the assessment of criteria for containment performance during severe accidents. The report describes recent major accomplishments in understanding the underlying phenomena that can occur during a severe accident. These include Mark I liner failure, severe accident scaling methodology, source term issues, core-concrete interactions, hydrogen transport and combustion, TMI-2 Vessel Investigation Project, and direct containment heating. The report also describes the major planned activities under the SARP over the next several years. These activities will focus on two phenomenological issues (core melt progression, and fuel-coolant interactions and debris coolability) that have significant uncertainties that impact our understanding and ability to predict severe accident phenomena and their effect on containment performance SARP will also focus on severe accident code development, assessment and validation. As the staff completes the research on severe accident issues that relate to current generation reactors, continued research will focus on efforts to independently evaluate the capability of new advanced light water reactor designs to withstand severe accidents

Application of the severe accident code ATHLET-CD. Modelling and evaluation of accident management measures (Project WASA-BOSS)

Energy Technology Data Exchange (ETDEWEB)

Wilhelm, Polina; Jobst, Matthias; Kliem, Soeren; Kozmenkov, Yaroslav; Schaefer, Frank [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Reactor Safety

2016-07-01

The improvement of the safety of nuclear power plants is a continuously on-going process. The analysis of transients and accidents is an important research topic, which significantly contributes to safety enhancements of existing power plants. In case of an accident with multiple failures of safety systems core uncovery and heat-up can occur. In order to prevent the accident to turn into a severe one or to mitigate the consequences of severe accidents, different accident management measures can be applied. Numerical analyses are used to investigate the accident progression and the complex physical phenomena during the core degradation phase, as well as to evaluate the effectiveness of possible countermeasures in the preventive and mitigative domain [1, 2]. The presented analyses have been performed with the computer code ATHLET-CD developed by GRS [3, 4].

Arguments against nuclear engineering

International Nuclear Information System (INIS)

Hahn, L.

1991-01-01

The arguments put forward are: data from risk studies concerning the frequency of occurrence of core meltdown in LWR type reactors, the frequency of containment failures and resulting off-site emissions, in-plant accident management, and the hazard of hydrogen explosions. Yet unresolved problems are stated to be: the presentation of results of the German Risk Study (part DRS-B), the way accident management is dealt with, the evaluation standards applied to safety deficits, the hydrogen problem, the biological effects of low-dose radiation, the qualification of radwaste repositories, the information policy of public authorities, and the regime of governmental control and supervision. (HP) [de

Fukushima Daiichi Radionuclide Inventories

Energy Technology Data Exchange (ETDEWEB)

Cardoni, Jeffrey N. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jankovsky, Zachary Kyle [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-09-01

Radionuclide inventories are generated to permit detailed analyses of the Fukushima Daiichi meltdowns. This is necessary information for severe accident calculations, dose calculations, and source term and consequence analyses. Inventories are calculated using SCALE6 and compared to values predicted by international researchers supporting the OECD/NEA's Benchmark Study on the Accident at Fukushima Daiichi Nuclear Power Station (BSAF). Both sets of inventory information are acceptable for best-estimate analyses of the Fukushima reactors. Consistent nuclear information for severe accident codes, including radionuclide class masses and core decay powers, are also derived from the SCALE6 analyses. Key nuclide activity ratios are calculated as functions of burnup and nuclear data in order to explore the utility for nuclear forensics and support future decommissioning efforts.

German risk study 'nuclear power plants, phase B'

International Nuclear Information System (INIS)

Heuser, F.W.

1989-01-01

The results of the German risk study 'Nuclear power plants, phase B' indicate that an accident in a nuclear power plant which cannot be managed by the safety systems according to design, is extremely improbable: Its probability is at about 3 to 100,000 per year and plant. Even if the safety systems fail, emergency measures can be effected in a nuclear power plant to prevent an accident. These in-plant emergency measures diminish the probability of a core meltdown to about 4 to 1,000,000 per year and plant. Hence, the accident risk is greatly reduced. The information given by the author are to smooth the emotional edge in the discussion about the safety of nuclear power plants. (orig.) [de

Numerical predictions of natural convection in a uniformly heated pool

International Nuclear Information System (INIS)

Tzanos, C.P.; Cho, D.H.

1993-01-01

In the event of a core meltdown accident, one of the accident progression paths is fuel relocation to the lower reactor plenum. In the heavy-water new production reactor (NPR-HWR) design, the reactor cavity is flooded with water. In such a design, decay heat removal to the water in the reactor cavity and thence to the containment may be adequate to keep the reactor vessel temperature below failure limits. If this is the case, the accident progression can be arrested by retaining a coolable corium configuration in the lower reactor plenum. The strategy of reactor cavity flooding to prevent reactor vessel failure from molten corium relocation to the reactor vessel lower head has also been considered for commercial pressurized water reactors

CINETHICA - Core accident analysis code

International Nuclear Information System (INIS)

Nakata, H.

1989-10-01

A computer program for nuclear accident analysis has been developed based on the point-kinetics approximation and one-dimensional heat transfer model for reactivity feedback calculation. Hansen's method/1/ were used for the kinetics equation solution and explicit Euler method were adopted for the thermohidraulic equations. The results were favorably compared to those from the GAPOTKIN Code/2/. (author) [pt

Deterministic analyses of severe accident issues

International Nuclear Information System (INIS)

Dua, S.S.; Moody, F.J.; Muralidharan, R.; Claassen, L.B.

2004-01-01

Severe accidents in light water reactors involve complex physical phenomena. In the past there has been a heavy reliance on simple assumptions regarding physical phenomena alongside of probability methods to evaluate risks associated with severe accidents. Recently GE has developed realistic methodologies that permit deterministic evaluations of severe accident progression and of some of the associated phenomena in the case of Boiling Water Reactors (BWRs). These deterministic analyses indicate that with appropriate system modifications, and operator actions, core damage can be prevented in most cases. Furthermore, in cases where core-melt is postulated, containment failure can either be prevented or significantly delayed to allow sufficient time for recovery actions to mitigate severe accidents

Approach to accident management in RBMK-1500

International Nuclear Information System (INIS)

Kaliatka, A.; Urbonavicius, E.; Uspuras, E.

2008-01-01

In order to ensure the safe operation of the nuclear power plants accident management programs are being developed around the world. These accident management programs cover the whole spectrum of accidents, including severe accidents. A lot of work is done to investigate the severe accident phenomena and implement severe accident management in NPPs with vessel-type reactors, while less attention is paid to channel-type reactors CANDU and RBMK. Ignalina NPP with RBMK-1500 reactor has implemented symptom based emergency operation procedures, which cover management of accidents until the core damage and do not extend to core damage region. In order to ensure coverage of the whole spectrum of accidents and meet the requirements of IAEA the severe accident management guidelines have to be developed. This paper presents the basic principles and approach to management of beyond design basis accidents at Ignalina NPP. In general, this approach could be applied to NPPs with RBMK-1000 reactors that are available in Russia, but the design differences should be taken into account

CARNSORE: Hypothetical reactor accident study

International Nuclear Information System (INIS)

Walmod-Larsen, O.; Jensen, N.O.; Kristensen, L.; Meide, A.; Nedergaard, K.L.; Nielsen, F.; Lundtang Petersen, E.; Petersen, T.; Thykier-Nielsen, S.

1984-06-01

Two types of design-basis accident and a series of hypothetical core-melt accidents to a 600 MWe reactor are described and their consequences assessed. The PLUCON 2 model was used to calculate the consequences which are presented in terms of individual and collective doses, as well as early and late health consequences. The site proposed for the nucelar power station is Carnsore Point, County Wexford, south-east Ireland. The release fractions for the accidents described are those given in WASH-1400. The analyses are based on the resident population as given in the 1979 census and on 20 years of data from the meteorological stations at Rosslare Harbour, 8.5 km north of the site. The consequences of one of the hypothetical core-melt accidents are described in detail in a meteorological parametric study. Likewise the consequences of the worst conceivable combination of situations are described. Finally, the release fraction in one accident is varied and the consequences of a proposed, more probable ''Class 9 accident'' are presented. (author)

The role of systems availability and operator actions in accident management

International Nuclear Information System (INIS)

Lutz, R.J. Jr.; Scobel, J.H.

1988-01-01

Traditional analyses of severe accidents, such as those presented in Probabilistic Risk Assessment (PRA) studies of nuclear power stations, have generally been performed on the assumption that all means of cooling the reactor core are lost and that no operator actions to mitigate the consequences or progression of the severe accident are performed. The assumption to neglect the availability of safety systems and operator actions which do not prevent core melting can lead to erroneous conclusions regarding the plant severe accident profile. Recent work in severe accident management has identified the need to perform analyses which consider all systems availabilities and operator actions, irrespective of their contribution to the prevention of core melting. These new analyses have far reaching conclusions. The analysis results indicate an unacceptably high degree of simplicity in the present severe accident analyses for Probabilistic Risk Assessment studies; the simplicity is in the assumption that systems availabilities and operator actions which do not impact core melt frequency can be neglected in the severe accident analyses. This results in overly pessimistic predictions of the time of core melting and the subsequent potential for recovery of core cooling prior to core melting. This simplicity can have a considerable impact on severe accident decision making, particularly in the evaluation of alternate plant design features and the priorities for research studies

Design approach to local blockages

International Nuclear Information System (INIS)

Roychowdhury, D.G.; Govindarajan, S.; Chetal, S.C.; Bhoje, S.B.

2000-01-01

In LMFBR, whole core meltdown accident falls in residual risk category. Propagation of a local fault to whole core, however, needs attention. Subassembly accidents are divided into two categories, Design Basis and Beyond Design Basis accidents. Design Basis is further classified into four categories. All events affecting fuel pin performance are identified and categorised, Total Instantaneous Blockage has been identified as the envelope of all local faults and categorised as BDB event and the safety objective is to demonstrate that no damage will propagate beyond six neighbouring SA. A core catcher has been provided for retention of core debris and cooling it by natural convection. Local blockages may be active and passive. Active blockages can be detected by DND signal. For passive blockages, detection is difficult. Hence, development of a finite volume computer code based on the porous body formulation has been undertaken to define the maximum allowable defect. Experimental programmes have been undertaken to understand blockage mechanism, define maximum credible defect and the thermalhydraulic behaviour of SA with local blockages. Also an experimental programme with a totally blocked SA with a bundle of heated pins has been undertaken to understand the behaviour of the SA. (author)

Simulant - water experiments to characterize the debris bed formed in severe core melt accidents

International Nuclear Information System (INIS)

Mathai, Amala M.; Anandan, J.; Sharma, Anil Kumar; Murthy, S.S.; Malarvizhi, B.; Lydia, G.; Das, Sanjay Kumar; Nashine, B.K.; Selvaraj, P.

2015-01-01

Molten Fuel Coolant Interaction (WO) and debris bed configuration on the core catcher plate assumes importance in assessing the Post Accident Heat Removal (PARR) of a heat generating debris bed. The key factors affecting the coolability of the debris bed are the bed porosity, morphology of the fragmented particles, degree of spreading/heaping of the debris on the core catcher and the fraction of lump formed. Experiments are conducted to understand the fragmentation kinetics and subsequent debris bed formation of molten woods metal in water at interface temperatures near the spontaneous nucleation temperature of water. Morphology of the debris particles is investigated to understand the fragmentation mechanisms involved. The spreading behavior of the debris on the catcher plate and the particle size distribution are presented for 5 kg and 10 kg melt inventories. Porosity of the undisturbed bed on the catcher plate is evaluated using a LASER sensor technique. (author)

Analysis of hypothetical LMFBR whole-core accidents in the USA

International Nuclear Information System (INIS)

Ferguson, D.R.; Deitrich, L.W.; Brown, N.W.; Waltar, A.E.

1978-01-01

Methods used for analysis of material behaviour, accident phenomenology and integrated accident calculations are reviewed. Applications of these methods to hypothetical LOF and TOP accidents are discussed. Recent results obtained from applications to FFTF and CRBRP are presented. (author)

Coolability of severely degraded CANDU cores

International Nuclear Information System (INIS)

Meneley, D.A.; Blahnik, C.; Rogers, J.T.; Snell, V.G.; Mijhawan, S.

1995-07-01

Analytical and experimental studies have shown that the separately cooled moderator in a CANDU reactor provides an effective heat sink in the event of a loss-of-coolant accident (LOCA) accompanied by total failure of the emergency core cooling system (ECCS). The moderator heat sink prevents fuel melting and maintains the integrity of the fuel channels, therefore terminating this severe accident short of severe core damage. Nevertheless, there is a probability, however low, that the moderator heat sink could fail in such an accident. The pioneering work of Rogers (1984) for such a severe accident using simplified models showed that the fuel channels would fail and a bed of dry, solid debris would be formed at the bottom of the calandria which would heat up and eventually melt. However, the molten pool of core material would be retained in the calandria vessel, cooled by the independently cooled shield-tank water, and would eventually re solidify. Thus, the calandria vessel would act inherently as a core-catcher as long as the shield tank integrity is maintained. The present paper reviews subsequent work on the damage to a CANDU core under severe accident conditions and describes an empirically based mechanistic model of this process. It is shown that, for such severe accident sequences in a CANDU reactor, the end state following core disassembly consists of a porous bed of dry solid, coarse debris, irrespective of the initiating event and the core disassembly process. (author). 48 refs., 3 tabs., 18 figs

A current perspective on the risk significance of steam explosions

International Nuclear Information System (INIS)

Snyder, A.W.

1982-01-01

The view currently held in the Sandia National Laboratory is that, in the case of a meltdown in the reactor core, the probability of a steam explosion is greater than was estimated in WASH-1400, but that the extent and effect of an explosion will be very much smaller than assumed in WASH-1400. This results in a far smaller total risk with regard to containment. In WASH-1400, a nominal conditional probability of 1% was assumed for a containment rupture in a PWR-type reactor, should a large part of the reactor fuel be subject to meltdown during the course of the accident. The German risk analysis study 'Deutsche Risikostudie Kernkraftwerke' dated 1979 considers an explosion of a size sufficient to represent a threat to containment to be considerably more improbable than was assumed in WASH-1400. (orig./DG) [de

Chernobyl: recovery operations and the entombment of Reactor 4

International Nuclear Information System (INIS)

Dalziel, S.P.C.

1988-01-01

The immediate actions taken following the accident at the Chernobyl-number 4 reactor in April 1986 are described. These included actions to put out the fires, initial medical aid and the dropping of sand, lead, dolomite and boron onto the reactor from helicopters. Following this the chamber below the damaged reactor core was filled with concrete to prevent any further explosions or meltdown. The reactor was subsequently entombed in steel and concrete. The evacuation of the surrounding area is also mentioned. (U.K.)

NPP Krsko Severe Accident Management Guidelines Implementation

International Nuclear Information System (INIS)

Basic, I.; Krajnc, B.; Bilic-Zabric, T.; Spiler, J.

2002-01-01

Severe Accident Management is a framework to identify and implement the Emergency Response Capabilities that can be used to prevent or mitigate severe accidents and their consequences. The USA NRC has indicated that the development of a licensee plant specific accident management program will be required in order to close out the severe accident regulatory issue (Ref. SECY-88-147). Generic Letter 88-20 ties the Accident management Program to IPE for each plant. The SECY-89-012 defines those actions taken during the course of an accident by the plant operating and technical staff to: 1) prevent core damage, 2) terminate the progress of core damage if it begins and retain the core within the reactor vessel, 3) maintain containment integrity as long as possible, and 4) minimize offsite releases. The subject of this paper is to document the severe accident management activities, which resulted in a plant specific Severe Accident Management Guidelines implementation. They have been developed based on the Krsko IPE (Individual Plant Examination) insights, Generic WOG SAMGs (Westinghouse Owners Group Severe Accident Management Guidances) and plant specific documents developed within this effort. Among the required plant specific actions the following are the most important ones: Identification and documentation of those Krsko plant specific severe accident management features (which also resulted from the IPE investigations). The development of the Krsko plant specific background documents (Severe Accident Plant Specific Strategies and SAMG Setpoint Calculation). Also, paper discusses effort done in the areas of NPP Krsko SAMG review (internal and external ), validation on Krsko Full Scope Simulator (Severe Accident sequences are simulated by MAAP4 in real time) and world 1st IAEA Review of Accident Management Programmes (RAMP). (author)

Development of severe accident analysis code - A study on the molten core-concrete interaction under severe accidents

Energy Technology Data Exchange (ETDEWEB)

Jung, Chang Hyun; Lee, Byung Chul; Huh, Chang Wook; Kim, Doh Young; Kim, Ju Yeul [Seoul National University, Seoul (Korea, Republic of)

1996-07-01

The purpose of this study is to understand the phenomena of the molten core/concrete interaction during the hypothetical severe accident, and to develop the model for heat transfer and physical phenomena in MCCIs. The contents of this study are analysis of mechanism in MCCIs and assessment of heat transfer models, evaluation of model in CORCON code and verification in CORCON using SWISS and SURC Experiments, and 1000 MWe PWR reactor cavity coolability, and establishment a model for prediction of the crust formation and temperature of melt-pool. The properties and flow condition of melt pool covering with the conditions of severe accident are used to evaluate the heat transfer coefficients in each reviewed model. Also, the scope and limitation of each model for application is assessed. A phenomenological analysis is performed with MELCOR 1.8.2 and MELCOR 1.8.3 And its results is compared with corresponding experimental reports of SWISS and SURC experiments. And the calculation is performed to assess the 1000 MWe PWR reactor cavity coolability. To improve the heat transfer model between melt-pool and overlying coolant and analyze the phase change of melt-pool, 2 dimensional governing equations are established using the enthalpy method and computational program is accomplished in this study. The benchmarking calculation is performed and its results are compared to the experiment which has not considered effects of the coolant boiling and the gas injection. Ultimately, the model shall be developed for considering the gas injection effect and coolant boiling effect. 66 refs., 10 tabs., 29 refs. (author)

Applications of nano-fluids to enhance LWR accidents management in in-vessel retention and emergency core cooling systems

International Nuclear Information System (INIS)

Chupin, A.; Hu, L. W.; Buongiorno, J.

2008-01-01

Water-based nano-fluid, colloidal dispersions of nano-particles in water; have been shown experimentally to increase the critical heat flux and surface wettability at very low concentrations. The use of nano-fluids to enhance accidents management would allow either to increase the safe margins in case of severe accidents or to upgrade the power of an existing power plant with constant margins. Building on the initial work, computational fluid dynamics simulations of the nano-fluid injection system have been performed to evaluate the feasibility of a nano-fluid injection system for in-vessel retention application. A preliminary assessment was also conducted on the emergency core cooling system of the European Pressurized Reactor (EPR) to implement a nano-fluid injection system for improving the management of loss of coolant accidents. Several design options were compared/or their respective merits and disadvantages based on criteria including time to injection, safety impact, and materials compatibility. (authors)

Core disruptive accident analysis in prototype fast breeder reactor

International Nuclear Information System (INIS)

Chellapandi, P.; Velusamy, K.; Kannan, S.E.; Singh, Om Pal; Chetal, S.C.; Bhoje, S.B.

2002-01-01

Liquid metal cooled fast breeder reactors, in particular, pool type have many inherent and engineered safety features and hence a core disruptive accident (CDA) involving melt down of the whole core is a very low probable event ( -6 /ry). The important mechanical consequences such as straining of the main vessel including top shield, structural integrity of safety grade decay heat exchangers (DHX) and intermediate heat exchangers (IHX) sodium release to reactor containment building (RCB) through the penetrations in the top shield, sodium fire and consequent temperature and pressure rise in RCB are theoretically analysed using computer codes. Through the analyses with these codes, it is demonstrated that an energetic CDA capability to the maximum 100 MJ mechanical energy in PFBR can be well contained in the primary containment. The sodium release to RCB is 350 kg and pressure rise in RCB is ∼10 kPa. In order to raise the confidence on the theoretical predictions, very systematic experimental program has been carried out. Totally 67 tests were conducted. This experimental study indicated that the primary containment is integral. The main vessel can withstand the energy release of ∼1200 MJ. The structural integrity of IHX and DHX is assured up to 200 MJ. The transient force transmitted to reactor vault is negligible. The average water leak measured under simulated tests for 122 MJ work potential is about 1.8 kg and the maximum leak is 2.41 kg. Extrapolation of the measured maximum leak based on simulation principles yields ∼ 233 kg of sodium leak in the reactor. Based on the above-mentioned theoretical and experimental investigations, the design pressure of 20 kPa is used for PFBR

Nuclear accidents. Three mile Island (United States)

International Nuclear Information System (INIS)

Duco, J.

2004-01-01

This paper describes the accident of Three Miles Island power plant which occurred the 28 march 1979 in the United States. The accident scenario, the consequences and the reactor core and vessel, after the accident, are analyzed. (A.L.B.)

Coolability of severely degraded CANDU cores. Revised

International Nuclear Information System (INIS)

Meneley, D.A.; Blahnik, C.; Rogers, J.T.; Snell, V.G.; Nijhawan, S.

1996-01-01

Analytical and experimental studies have shown that the separately cooled moderator in a CANDU reactor provides an effective heat sink in the event of a loss-of-coolant accident (LOCA) accompanied by total failure of the emergency core cooling system (ECCS). The moderator heat sink prevents fuel melting and maintains the integrity of the fuel channels, therefore terminating this severe accident short of severe core damage. Nevertheless, there is a probability, however low, that the moderator heat sink could fail in such an accident. The pioneering work of Rogers (1984) for such a severe accident using simplified models showed that the fuel channels would fail and a bed of dry, solid debris would be formed at the bottom of the calandria which would heat up and eventually melt. However, the molten pool of core material would be retained in the calandria vessel, cooled by the independently cooled shield-tank water, and would eventually resolidify. Thus, the calandria vessel would act inherently as a 'core-catcher' as long as the shield tank integrity is maintained. The present paper reviews subsequent work on the damage to a CANDU core under severe accident conditions and describes an empirically based mechanistic model of this process. It is shown that, for such severe accident sequences in a CANDU reactor, the end state following core disassembly consists of a porous bed of dry solid, coarse debris, irrespective of the initiating event and the core disassembly process. (author)

Calculation of individual and population doses on Danish territory resulting from hypothetical core-melt accidents at the Barsebaeck reactor

International Nuclear Information System (INIS)

1977-01-01

Individual and population doses within Danish territory are calculated from hypothetical, severe core-melt accidents at the Swedish nuclear plant at Barsebaeck. The fission product inventory of the Barsebaeck reactor is calculated. The release fractions for the accidents are taken from WASH-1400. Based on parametric studies, doses are calculated for very unfavourable, but not incredible weather conditions. The probability of such conditions in combination with wind direction towards Danish territory is estimated. Doses to bone marrow, lungs, GI-tract and thyroid are calculated based on dose models developed at Risoe. These doses are found to be consistent with doses calculated with the models used in WASH-1400. (author)

Conditions for oxygen-deficient combustion during accidents with severe core concrete thermal attack

International Nuclear Information System (INIS)

Luangdilok, W.; Elicson, G.T.; Berger, W.E. Jr.

1993-01-01

This paper addresses the interactions between MCCI (molten core-concrete interactions)-induced offgas releases, mostly the combustible gases, natural circulation between the cavity and the lower containment based on recent research developments in the area of mixed convection flow (Epstein, et al., 1989; Epstein, 1988; Epstein, 1992) between compartments, and their effects on combustion in PWR containments during prolonged severe accidents. Specifically, large dry PWR containments undergoing severe core-concrete attack during station blackouts where the containment atmosphere is expected to be inerted are objects of this analysis. The purpose of this paper, given the conditions that oxygen can be brought to the cavity, is to demonstrate that consumption of most oxygen present in the containment can be achieved in a reasonable time scale assuming that combustion is not subject to flammability limits due to the high cavity temperatures. The conditions for cavity combustion depend on several factors including good gas flowpaths between the cavity and other containment regions, and combustion processes within the cavity with the hot debris acting as the ignition source

The management of severe accidents in modern pressure tube reactors

International Nuclear Information System (INIS)

Popov, N.K.; Santamaura, P.; Blahnik, C.; Snell, V.G.; Duffey, R.B.

2007-01-01

Advanced new reactor designs resist severe accidents through a balance between prevention and mitigation. This balance is achieved by designing to ensure that such accidents are very rare; and by limiting core damage progression and releases from the plant in the event of such rare accidents. These design objectives are supported by a suitable combination of probabilistic safety analysis, engineering judgment and experimental and analytical study. This paper describes the approach used for the Advanced CANDU Reactor TM -1000 (ACR-1000) design, which includes provisions to both prevent and mitigate severe accidents. The paper describes the use of PSA as a 'design assist' tool; the analysis of core damage progression pathways; the definition of the core damage states; the capability of the mitigating systems to stop and control severe accident events; and the severe accident management opportunities for consequence reduction. (author)

TMI-2 core examination plan

International Nuclear Information System (INIS)

Owen, D.E.; MacDonald, P.E.; Hobbins, R.R.; Ploggr, S.A.

1982-01-01

The Three Mile Island (TMI-2) core examination is divided into four stages: (1) before removing the head; (2) before removing the plenum; (3) during defueling; and (4) offsite examinations. Core examinations recommended during the first three stages are primarily devoted to documenting the post-accident condition of the core. The detailed analysis of core damage structures will be performed during offsite examinations at government and commercial hot cell facilities. The primary objectives of these examinations are to enhance the understanding of the degraded core accident sequence, to develop the technical bases for reactor regulations, and to improve LWR design and operation

Thermal-hydraulic uncertainties affecting severe accident progression

International Nuclear Information System (INIS)

Haskin, F.E.; Behr, V.L.

1984-01-01

To provide the proper technical bases for decisions regarding severe accidents, the US Nuclear Regulatory Commission (NRC) is sponsoring the following activities: (a) a variety of severe accident research programs, combined under the Severe Accident Research Plan; (b) nationwide task forces on containment loading, containment response, and fission product source terms; (c) a review by the American Physical Society of state-of-the-art methods for calculating radiological source terms; and (d) technical exchange meetings with the Industry Degraded Core (IDCOR) program. One of the means for integrating this developing array of technical information is the Severe Accident Risk Reduction Program (SARRP). One of the current SARRP objectives is to utilize insights gained from the activities listed above to characterize the relative likelihoods of competing containment failure modes for core-melt accidents

Severe accident recriticality analyses (SARA)

DEFF Research Database (Denmark)

Frid, W.; Højerup, C.F.; Lindholm, I.

2001-01-01

with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality-both super-prompt power bursts and quasi steady-state power......Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies......, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g(-1), was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s(-1). In most cases, however, the predicted energy deposition was smaller, below...

On fission product retention in the core of the low powered high temperature reactor under accident conditions

International Nuclear Information System (INIS)

Bastek, H.

1984-01-01

In the core of the high temperature reactor the fuel element and the coated particles contained herein provide the safest enclosure for fission products. The complex process of fission product transport out of the particle kernel, through the particle coating and within the fuel element graphite is described in a simplified form by the Fick's diffusion. The effective diffusion coefficient is used for calculation. Starting from the existing ideas of fission product transport five burn-up and temperature-dependent diffusion coefficients for Cesium in (Th,U)O 2 -kernels are derived in this study. The results have been gained from several fuel element radiation experiments in recent years, which showed extreme variation in regard to burn-up, temperature cycle, neutron flux and operation time. Cs-137 release measurements from single particle kernels were present from all the experiments. Furthermore, annealing tests of AVR-fuel elements were analyzed. Heat-temperatur and heating-time, the fuel element burn-up in the AVR-reactor, as well as the measured Cs-137 inventory of the fuel elements before and after annealing, are included in the investigation as essential parameters. With the aid of the derived diffusion coeffizients and already present data sets the Cs-137 release of fuel elements into a small reactor core is investigated under unrestricted core heat-up. While the released Cs-137 is derived mainly from defective particles at accident temperatures up to 1600 0 C, the main part diffuses through the particle coating at higher accident temperatures. (orig./HP) [de

Residual risk over-estimated

International Nuclear Information System (INIS)

Anon.

1982-01-01

The way nuclear power plants are built practically excludes accidents with serious consequences. This is attended to by careful selection of material, control of fabrication and regular retesting as well as by several safety systems working independently. But the remaining risk, a 'hypothetic' uncontrollable incident with catastrophic effects is the main subject of the discussion on the peaceful utilization of nuclear power. The this year's 'Annual Meeting on Nuclear Engineering' in Mannheim and the meeting 'Reactor Safety Research' in Cologne showed, that risk studies so far were too pessimistic. 'Best estimate' calculations suggest that core melt-down accidents only occur if almost all safety systems fail, that accidents take place much more slowly, and that the release of radioactive fission products is by several magnitudes lower than it was assumed until now. (orig.) [de

Modelling of RPV lower head under core melt severe accident condition using OpenFOAM

International Nuclear Information System (INIS)

Madokoro, Hiroshi; Kretzschmar, Frank; Miassoedov, Alexei

2017-01-01

Although six years have been passed since the tragic severe accident at Fukushima Daiichi, still large uncertainties exist in modeling of core degradation and reactor pressure vessel (RPV) failure. It is extremely important to obtain a better understanding of complex phenomena in the lower head in order to improve accident management measures. The possible failure mode of reactor pressure vessel and its failure time are especially a matter of importance. Thermal behavior of the molten pool can be simulated by the Phase-change Effective Convectivity Model (PECM), which is a distributed-parameter model developed in the Royal Institute of Technology (KTH), Sweden. The model calculates convective currents not using a pure CFD approach but based on so called “characteristic velocities” that are determined by empirical correlations depending on the geometry and physical properties of the molten pool. At the Karlsruhe Institute of Technology (KIT), the PECM has been implemented in the open-source CFD software OpenFOAM in order to receive detailed predictions of a core melt behavior in the RPV lower head under severe accident conditions. An advantage of using OpenFOAM is that it is very flexible to add and modify models and physical properties. In the current work, the solver is extended to couple PECM with a structure analysis model of the vessel wall. The model considers thermal expansion, plasticity, creep and damage. The model and physical properties are based on those implemented in ANSYS. Although the previous implementation had restriction that the amount of and geometry of the melt cannot be changed, our coupled model allows flexibility of the melt amount and geometry. The extended solver was used to simulate the LIVE-L1 and -L7V experiments and has demonstrated good prediction of the temperature distribution in the molten pool and heat flux distribution through the vessel wall. Regarding the vessel failure the model was applied to one of the FOREVER tests

Comparative analysis of a hypothetical loss-of-flow accident in an irradiated LMFBR core using different computer models for a common benchmark problem

International Nuclear Information System (INIS)

Wider, H.U.; Devos, J.; Nguyen, H.; Goethem, G. Van.; Miles, K.J.; Tentner, A.M.; Pizzica, P.

1989-01-01

This report summarizes the results of an international exercise to compare whole-core accident calculations of the initiation phase of an unprotected LOF accident in a large irradiated LMFBR. The results for the accident phase before pin failure are in rather good agreement except for the fuel pin mechanics predictions. There are also some differences in the sodium boiling calculations but the voiding rates which are of key importance are very similar. The post - failure fuel motion and sodium voiding predictions show significant differences. However, the majority of these calculations agree that temporary fuel accumulations occur which increase the power beyond that caused by sodium voiding alone

Evaluation of final vapor pressures in the loss of flow accident in an irradiation device of a pool reactor core

International Nuclear Information System (INIS)

Verri, A.

1987-01-01

The reliability feature, are described for a device containing samples, at a temperatures of 300 grade centigrades, in a reactor core for a long time. After an examination of the maximum accident event, the maximum vapour pressure originated by the inlet of reactor cooling water into the experimental device, is evaluated

Assessment of fission product release from the reactor containment building during severe core damage accidents in a PWR

International Nuclear Information System (INIS)

Fermandjian, J.; Evrard, J.M.; Generino, G.

1984-07-01

Fission product releases from the RCB associated with hypothetical core-melt accidents ABβ, S 2 CDβ and TLBβ in a PWR-900 MWe have been performed using French computer codes (in particular, the JERICHO Code for containment response analysis and AEROSOLS/B1 for aerosol behavior in the containment) related to thermalhydraulics and fission product behavior in the primary system and in the reactor containment building

Analysis of articles in weekly magazines on scientific issues related to Fukushima nuclear power plant accident

International Nuclear Information System (INIS)

Sano, Kazumi; Kikuchi, Macoto

2012-01-01

The large area was polluted by the radioactive fallout released after the nuclear fuel meltdown of Fukushima first nuclear plant of Tokyo electric power company. The news media that reported the accident were required to have scientific knowledge on the structure of the nuclear reactor and the physics and health issues of the radioactivity. In this paper, we focus on how the weekly magazines reported this critical accident. The weekly magazines are not regarded as a neutral news media. Rather, their articles in general strongly reflect the editorial opinions. In this sense, the weekly magazines are 'biased media'. So, there are many points to discuss from the view point of the science communication. We analyze the articles appeared in the seven major weekly magazines published during the first half year after the earthquake. We found that the differences in the scientific literacy between magazines are reflected, for example, in selection of the experts who made comments in articles. (author)

Safety evaluation report in the matter of Offshore Power Systems Floating Nuclear Plants (1-8). Docket No. STN 50-437

International Nuclear Information System (INIS)

1980-02-01

The staff has performed an evaluation of a refractory sacrificial bed, called a core ladle, proposed by Offshore Power Systems (OPS) to be installed in Floating Nuclear Plants (FNPs) to delay the melt-through penetration of molten core debris in the unlikely event of a core meltdown accident. The core ladle design as proposed by OPS is in response to the staff's manufacturing license Condition 4 given in the Final Environmental Statement, Part III, NUREG-0502, dated December 1978 (FES-III). This condition requires that a pad constructed of magnesium oxide, or other equivalent refractory material, be installed in the FNP structure within the lower reactor cavity. The material must provide increased resistance to melt-through by the molten reactor core, must not react with core debris to form a large volume of gases, and must not have any deleterious effects on safety

Assessment of two BWR accident management strategies

International Nuclear Information System (INIS)

Hodge, S.A.; Petek, M.

1991-01-01

A recently completed Oak Ridge effort proposes two management strategies for mitigation of the events that might occur in-vessel after the onset of significant core damage in a BWR severe accident. While the probability of such an accident is low, there may be effective yet inexpensive mitigation measures that could be implemented employing the existing plant equipment and requiring only additions to the plant emergency procedures. In this spirit, accident management strategies have been proposed for use of a borated solution for reactor vessel refill should control blade damage occur during a period of temporary core dryout and for containment flooding to maintain the core debris within the reactor vessel if injection systems cannot be restored. The proposed strategy for poisoning of the water used for vessel reflood should injection systems be restored after control blade damage has occurred has great promise, using only the existing plant equipment but employing a different chemical form for the boron poison. The dominant BWR severe accident sequence is Station Blackout and without means for mechanical stirring or heating of the storage tank, the question of being able to form the poisoned solution under accident conditions becomes of supreme importance. On the other hand, the proposed strategy for drywell flooding to cool the reactor vessel bottom head and prevent the core and structure debris from escaping to the drywell holds less promise. This strategy does, however, have potential for future plant designs in which passive methods might be employed to completely submerge the reactor vessel under severe accident conditions without the need for containment venting

Fuel temperature analysis method for channel-blockage accident in HTTR

International Nuclear Information System (INIS)

Maruyama, So; Fujimoto, Nozomu; Sudo, Yukio; Kiso, Yoshihiro; Hayakawa, Hitoshi

1994-01-01

During operation of the High Temperature Engineering Test Reactor (HTTR), coolability must be maintained without core damage under all postulated accident conditions. Channel blockage of a fuel element was selected as one of the design-basis accidents in the safety evaluation of the reactor. The maximum fuel temperature for such a scenario has been evaluated in the safety analysis and is compared to the core damage limits.For the design of the HTTR, an in-core thermal and hydraulic analysis code ppercase[flownet/trump] was developed. This code calculates fuel temperature distribution, not only for a channel blockage accident but also for transient conditions. The validation of ppercase[flownet/trump] code was made by comparison of the analytical results with the results of thermal and hydraulic tests by the Helium Engineering Demonstration Loop (HENDEL) multi-channel test rig (T 1-M ), which simulated one fuel column in the core. The analytical results agreed well with the experiments in which the HTTR operating conditions were simulated.The maximum fuel temperature during a channel blockage accident is 1653 C. Therefore, it is confirmed that the integrity of the core is maintained during a channel blockage accident. ((orig.))

Severe accident training simulator APROS SA

International Nuclear Information System (INIS)

Raiko, Eerikki; Salminen, Kai; Lundstroem, Petra; Harti, Mika; Routamo, Tomi

2003-01-01

APROS SA is a severe accident training simulator based on the APROS simulation environment. APROS SA has been developed in Fortum Nuclear Services Ltd to serve as a training tool for the personnel of the Loviisa NPP. Training with APROS SA gives the personnel a deeper understanding of the severe accident phenomena and thus it is an important part of the implementation of the severe accident management strategy. APROS SA consists of two parts, a comprehensive Loviisa plant model and an external severe accident model. The external model is an extension to the Loviisa plant model, which allows the simulation to proceed into the severe accident phase. The severe accident model has three submodels: the core melting and relocation model, corium pool model and fission product model. In addition to these, a new thermal-hydraulic solver is introduced to the core region of the Loviisa plant model to replace the more limited APROS thermal-hydraulic solver. The full APROS SA training simulator has a graphical user interface with visualizations of both severe accident management panels at the operator room and the important physical phenomena during the accident. This paper describes the background of the APROS SA training simulator, the severe accident submodels and the graphical user interface. A short description how APROS SA will be used as a training tool at the Loviisa NPP is also given

Accidents with damage to nuclear core. A perspective for TMI-2

International Nuclear Information System (INIS)

Alonso, A.

1980-01-01

The most direct consequence of the TMI-2 accident was the destruction of substantial fraction of the fuel element cladding. With the aim of given a certain perspective to that accident, an analysis is made of the causes by which the fuel element clad may lose its integrity. The Windscale, SL-1 and Enrico Fermi accidents constitute important examples to that end. These accidents are analyzed giving special emphasis to those aspects which apear later on at TMI-2. The general consequences of the latter are examined with a certain details, including the social, institutional, technological and economic aspects of the accident. (author)

Effect of engineered safety features on the risk of hypothetical LMFBR accidents

International Nuclear Information System (INIS)

Cybulskis, P.

1978-01-01

The risks of hypothetical core-disruptive accidents in liquid-metal-cooled fast breeder reactors which involve meltthrough of the reactor vessel are compared for two plant designs: one design without specific provisions to accommodate such an accident and the other design with an ex-vessel core catcher and a cvity hot liner. The approach to risk analysis used is that developed in the Reactor Safety Study (WASH-1400). Since the probability of occurrence of such an event has not been evaluated, however, insight into the potential risk is gained only on a relative basis. The principal conclusions of this study are: (1) adding a core catcher--hot liner reduces the probabilty of accidents having major consequences; (2) the degree to which hot liner--core catcher systems can reduce the risk of melt-through accidents is limited by the failure probability of these systems; (3) fractional radioactive releases to the environment in the liquid-metal-cooled fast breeder reactor accidents considered are comparable to those from the light-water reactors evaluated in WASH-1400; (4) since sodium--concrete reactions are a dominant driving force during the accident, the integrity of the cavity liner is as important as the function of the core catcher; (5) there may be other accidents or paths to radioactive releases that are not affected by the addition of a hot liner--core catcher

Present status and needs of research on severe core damage

International Nuclear Information System (INIS)

1982-05-01

The needs for research on severe core damage accident have been emphasized recently, in particular, since TMI-2 accident. The Severe Core Damage Research Task Force was established by the Divisions of Reactor Safety and Reactor Safety Evaluation to evaluate individual phenomenon, to survey the present status of research and to provide the recommended research subjects on severe accidents. This report describes the accident phenomena involving some analytical results, status of research and recommended research subjects on severe core damage accidents, divided into accident sequence, fuel damage, and molten material behavior, fission product behavior, hydrogen generation and combustion, steam explosion and containment integrity. (author)

Lessons of nuclear robot history

International Nuclear Information System (INIS)

Oomichi, Takeo

2014-01-01

Severe accidents occurred at Fukushima Daiichi Nuclear Power Station stirred up people's great expectation of nuclear robot's deployment. However unexpected nuclear disaster, especially rupture of reactor building caused by core meltdown and hydrogen explosion, made it quite difficult to introduce nuclear robot under high radiation environment to cease accidents and dispose damaged reactor. Robotics Society of Japan (RSJ) set up committee to look back upon lessons learned from 50 year's past experience of nuclear robot development and summarized 'Lessons of nuclear robot history', which was shown on the home page website of RSJ. This article outlined it with personal comment. History of nuclear robot developed for inspection and maintenance at normal operation and for specific required response at nuclear accidents was reviewed with many examples at home and abroad for TMI, Chernobyl and JCO accidents. Present state of Fukushima accident response robot's introduction and development was also described with some comments on nuclear robot development from academia based on lessons. (T. Tanaka)

Uncertainties and severe-accident management

International Nuclear Information System (INIS)

Kastenberg, W.E.

1991-01-01

Severe-accident management can be defined as the use of existing and or alternative resources, systems, and actions to prevent or mitigate a core-melt accident. Together with risk management (e.g., changes in plant operation and/or addition of equipment) and emergency planning (off-site actions), accident management provides an extension of the defense-indepth safety philosophy for severe accidents. A significant number of probabilistic safety assessments have been completed, which yield the principal plant vulnerabilities, and can be categorized as (a) dominant sequences with respect to core-melt frequency, (b) dominant sequences with respect to various risk measures, (c) dominant threats that challenge safety functions, and (d) dominant threats with respect to failure of safety systems. Severe-accident management strategies can be generically classified as (a) use of alternative resources, (b) use of alternative equipment, and (c) use of alternative actions. For each sequence/threat and each combination of strategy, there may be several options available to the operator. Each strategy/option involves phenomenological and operational considerations regarding uncertainty. These include (a) uncertainty in key phenomena, (b) uncertainty in operator behavior, (c) uncertainty in system availability and behavior, and (d) uncertainty in information availability (i.e., instrumentation). This paper focuses on phenomenological uncertainties associated with severe-accident management strategies

Hypothetical core disruptive accident analysis of a 2000 MWsub(e) liquid metal cooled fast breeder reactor

International Nuclear Information System (INIS)

Struwe, D.

1977-12-01

A structural phase diagram for hypothetical core disruptive accidents (HCDA) has been developed based on a variety of analyses for different LMFBR's. The intention was to identify the strategic phases of HCDA's important with regard to safety aspects of the plant. These phases are investigated in detail for a 2,000 MWsub(e) LMFBR (SNR-2,000). Characteristic data of SNR-2,000 are discussed concerning their influence on safety analysis. Reasons for the choice of model parameters for special phenomena as fuel coolant interaction, fuel pin failure mechanisms and sodium voiding are given. The results of calculations with CAPRI-2, HOPE and KADIS are analyzed for possibilities to enter energetic core disassembly with consequences, making power values below 2,000 MWsub(e) necessary. Investigation of these results shows that the expected consequences do not lead to design requirements, restricting the magnitude of the electrical power output of LMFBR's to values below 2,000 MWsub(e). Therefore, consequences of HCDA's are principal not expected to limit the feasibility of conventional core design of this order of magnitude. (orig.) [de

γ radiation level simulation and analysis with MCNP in EPR containment during severe accident

International Nuclear Information System (INIS)

Zeng Jun; Liu Shuhuan; Wang Yang; Zhai Liang

2013-01-01

The γ dosimetry model based on the EPR core structure, material composition and the designed shielding system was established. The γ-ray dose rate distributions in EPR containment under different conditions including normal operation state, loss-of-coolant accident and core melt severe accident were simulated with MCNP5, and the calculation results under normal operation state and severe accident were compared and analyzed respectively with that of the designed limit. The study results may provide some relative data reference for EPR core accident prediction and reactor accident emergency decision making. (authors)

Managing severe reactor accidents. A review and evaluation of our knowledge on reactor accidents and accident management

International Nuclear Information System (INIS)

Gustavsson, Veine

2002-11-01

The report gives a review of the results from the last years research on severe reactor accidents, and an opinion on the possibilities to refine the present strategies for accident management in Swedish and Finnish BWRs. The following aspect of reactor accidents are the major themes of the study: 1. Early pressure relief from hydrogen production; 2. Recriticality in re-flooded, degraded core; 3. Melt-through; 4. Steam explosion after melt-through; 5. Coolability of the melt after after melt-through; 6. Hydrogen fire in the reactor containment; 7. Leaking containment; 8. Hydrogen fire in the reactor building; 9. Long-time developments after a severe accident; 10. Accidents during shutdown for overhaul; 11. Information need for remedial actions. Possibilities for improving the strategies in each of these areas are discussed. The review shows that our knowledge is sufficient in the areas 1, 2, 4, 6, 8. For the other areas, more research is needed

An analysis of reactor structural response to fuel sodium interaction in a hypothetical core disruptive accident

International Nuclear Information System (INIS)

Suzuki, K.; Tashiro, M.; Sasanuma, K.; Nagashima, K.

1976-01-01

This study shows the effect of constraints around FSI zone on FSI phenomena and deformations of reactor structures. SUGAR-PISCES code system has been developed to evaluate the phenomena of FSI and the response of reactor structure. SUGAR calculates the phenomena of FSI. PISCES, developed by Physics International Company in U.S.A., calculates the dynamic response of reactor structure in two-dimensional, time-dependent finite-difference Lagrangian model. The results show that the peak pressure and energy by FSI and the deformation of reactor structures are about twice in case of FSI zone surrounding by blanket than by coolant. The FSI phenomena highly depend on the reactor structure and the realistic configuration around core must be considered for analyzing hypothetical core disruptive accident. This work was supported by a grant from Power Reactor and Nuclear Fuel Development Corporation. (auth.)

The Chernobyl accident: Causes and consequences

International Nuclear Information System (INIS)

Malinauskas, A.P.

1987-01-01

Two explosions, one immediately following the other, in Unit 4 of the Chernobyl nuclear power station in the Soviet Union signaled the worst disaster ever to befall the commercial nuclear power production industry. This accident, which occurred at 1:24 a.m. on April 26, 1986, resulted from an almost incredible series of operational errors associated, ironically, with an attempt to enhance the capability of the reactor to safely accommodate station blackout accidents (i.e., accidents arising from a loss of station electrical power). Disruption of the core, due to a prompt criticality excursion, resulted in the destruction of the core vault and reactor building and the sudden dispersal of about 3% of the fuel from the core region into the environment. Lesser but significant releases of radioactivity continued through May 6, 1986, before attempts to certain the radioactivity and cool the remnants of the core were successful. The amount and composition of material released in the course of the accident remain somewhat uncertain, and inconsistencies in the release estimates are evident. The Soviet estimates, in addition to the dispersal of about 3% of the fuel, include complete release of the noble gas core inventory, 20% of the fission product iodine inventory, 15% of the tellurium inventory, and 10 to 13% of the fission product cesium inventory. The iodine and cesium release estimates are not consistent with the noble gas values, and are as much as a factor of two less than some estimates made by experts outside the Soviet Union

German Light-Water-Reactor Safety-Research Program

International Nuclear Information System (INIS)

Seipel, H.G.; Lummerzheim, D.; Rittig, D.

1977-01-01

The Light-Water-Reactor Safety-Research Program, which is part of the energy program of the Federal Republic of Germany, is presented in this article. The program, for which the Federal Minister of Research and Technology of the Federal Republic of Germany is responsible, is subdivided into the following four main problem areas, which in turn are subdivided into projects: (1) improvement of the operational safety and reliability of systems and components (projects: quality assurance, component safety); (2) analysis of the consequences of accidents (projects: emergency core cooling, containment, external impacts, pressure-vessel failure, core meltdown); (3) analysis of radiation exposure during operation, accident, and decommissioning (project: fission-product transport and radiation exposure); and (4) analysis of the risk created by the operation of nuclear power plants (project: risk and reliability). Various problems, which are included in the above-mentioned projects, are concurrently studied within the Heiss-Dampf Reaktor experiments

Preliminary design of a borax internal core-catcher for a gas cooled fast reactor

International Nuclear Information System (INIS)

Dalle Donne, M.; Dorner, S.; Schumacher, G.

1976-09-01

Preliminary thermal calculations show that a core-catcher appears to be feasible, which is able to cope with the complete meltdown of the core and blankets of a 1,000 MWe GCFR. This core-catcher is based on borax (Na 2 B 4 O 7 ) as dissolving material of the oxide fuel and of the fission products occuring in oxide form. The borax is contained in steel boxes forming a 2.1 meter thick slab on the base of the reactor cavity inside the prestressed concrete reactor vessel, just underneath the reactor core. The fission products are dispersed in the pool formed by the liquid borax. The heat power density in the pool is conveniently reduced and the resulting heat fluxes at the borders of the pool can be safely carried away through the PCRV liner and its water cooling system. (orig.) [de

In-plant considerations for optimal offsite response to reactor accidents

International Nuclear Information System (INIS)

Burke, R.P.; Heising, C.D.; Aldrich, D.C.

1982-11-01

Offsite response decision-making methods based on in-plant conditions are developed for use during severe reactor-accident situations. Dose projections are used to eliminate all LWR plant systems except the reactor core and the spent-fuel storage pool from consideration for immediate offsite emergency response during accident situations. A simple plant information-management scheme is developed for use in offsite response decision-making. Detailed consequence calculations performed with the CRAC2 model are used to determine the appropriate timing of offsite-response implementation for a range of PWR accidents involving the reactor core. In-plant decision criteria for offsite-response implementation are defined. The definition of decision criteria is based on consideration of core-accident physical processes, in-plant accident monitoring information, and results of consequence calculations performed to determine the effectiveness of various public-protective measures. The benefits and negative aspects of the proposed response-implementation criteria are detailed

Decision No. 2008-DC-0114 of 26 September 2008 by the French Nuclear Safety Authority Setting Forth Specific Requirements to Be Met by Electricite de France - Societe anonyme (EDF-SA) at the Flamanville Nuclear site Regarding the Design and Construction of the Flamanville-3 (INB No. 167) NPP and the Operation of Flamanville-1 (INB No. 108) and Flamanville-2 (INB No. 109) NPPs

International Nuclear Information System (INIS)

2009-01-01

This decision sets forth the requirements to be met by Electricite de France (EDF-SA), the operator, regarding the design and construction of Basic Nuclear Installation ('installation nucleaire de base' - INB) No. 167 and the operation of INBs Nos. 108 and 109 on the Flamanville Site, Manche Department. The specific requirements applicable to INB No. 167 (Flamanville-3) are described in Annex 1. Common requirements applicable to INBs Nos. 167 (Flamanville 3), 108 (Flamanville 1) and 109 (Flamanville 2) are described in Annex 2. Content of the annex 1 (Requirements applicable to INB No. 167 - Flamanville-3): Organisation and management: Organisation and management, Operations to be declared to or approved by ASN; Accident-risk management: Process control (Nuclear safety demonstration, Compliance of operations, Analysis of internal and external hazards leading to hostile conditions or damages to structures, systems and components, Analysis of hazards caused by the environment of the installation that may induced hostile conditions or damages to structures, systems and components, Probabilistic studies, Specific studies, Environmental qualification of systems, equipment, material and components, Controls or tests performed to comply with the hypotheses used in safety demonstration); Prevention of accident conditions that may lead to large early releases (Core-meltdown situations occurring while the primary circuit is at high pressure, Fuel-meltdown situations in the spent-fuel cooling pool, Reactivity accidents resulting from the rapid introduction in the primary circuit of cold water or of water with an insufficient concentration of soluble neutron absorber, Core-meltdown situations with containment bypass, Global hydrogen detonations and steam explosions likely to compromise the integrity of the reactor containment), Basic nuclear safety functions of the installation (Common provisions, Reactivity control, Cooling of nuclear fuel, Containment of radioactive

Status of degraded core issues. Synthesis paper prepared by G. Bandini in collaboration with the NEA task group on degraded core cooling

International Nuclear Information System (INIS)

2001-02-01

The in-vessel evolution of a severe accident in a nuclear reactor is characterised, generally, by core uncover and heat-up, core material oxidation and melting, molten material relocation and debris behaviour in the lower plenum up to vessel failure. The in-vessel core melt progression involves a large number of physical and chemical phenomena that may depend on the severe accident sequence and the reactor type under consideration. Core melt progression has been studied in the last twenty years through many experimental works. Since then, computer codes are being developed and validated to analyse different reactor accident sequences. The experience gained from the TMI-2 accident also constitutes an important source of data. The understanding of core degradation process is necessary to evaluate initial conditions for subsequent phases of the accident (ex-vessel and within the containment), and define accident management strategies and mitigative actions for operating and advanced reactors. This synthesis paper, prepared within the Task Group on Degraded Core Cooling (TG-DCC) of PWG2, contains a brief summary of current views on the status of degraded core issues regarding light water reactors. The in-vessel fission product release and transport issue is not addressed in this paper. The areas with remaining uncertainties and the needs for further experimental investigation and model development have been identified. The early phase of core melt progression is reasonably well understood. Remaining uncertainties may be addressed on the basis of ongoing experimental activities, e.g. on core quenching, and research programs foreseen in the near future. The late phase of core melt progression is less understood. Ongoing research programs are providing additional valuable information on corium molten pool behaviour. Confirmatory research is still required. The pool crust behaviour and material relocation into the lower plenum are the areas where additional research should

What is the purpose of risk studies

International Nuclear Information System (INIS)

Birkhofer, A.

1986-01-01

Over the past few years, more or less comprehensive risk analyses have been carried out for numerous nuclear power plants, especially in the USA. The first risk studies conducted, especially the Rasmussen Study and the 'German Risk Study,' investigated sequences of accidents up to their environmental impacts. Risk studies today are focused mostly on assessments of technical safety, which is why they are extended only as far as the determination of core meltdown frequencies or radionuclide releases. Studies of this type are also called probabilistic safety analyses. (orig.) [de

In-core monitoring detectors

International Nuclear Information System (INIS)

Mitelman, M.G.

2001-01-01

The main task of in-core monitoring consists in securing observability of the reactor installation in all possible operation modes (normal, transient, accident and post-accident). Operation safety at acceptable cost can be achieved by optimized measurement errors. The range of sensors applied as in-core detectors for operative measurements in the industry is very limited in number. Among them might be cited self powered neutron detectors (SPND) and thermocouples. Sensors are incorporated in the in-core detectors assemblies (SVRD). The presentation makes an effort to touch upon the problems of assuring and increasing quality of in-core on-line measurements. So we do not consider systems using movable detectors, as the latter do not assure on-line measurements. (Authors)

NPP Krsko Severe Accident Management Guidelines Upgrade

International Nuclear Information System (INIS)

Mihalina, Mario; Spalj, Srdjan; Glaser, Bruno; Jalovec, Robi; Jankovic, Gordan

2014-01-01

Nuclear Power Plant Krsko (NEK) has decided to take steps for upgrade of safety measures to prevent severe accidents, and to improve the means to successfully mitigate their consequences. The content of the program for the NEK Safety Upgrade is consistent with the nuclear industry response to Fukushima accident, which revealed many new insights into severe accidents. Therefore, new strategies and usage of new systems and components should be integrated into current NEK Severe Accident Management Guidelines (SAMG's). SAMG's are developed to arrest the progression of a core damage accident and to limit the extent of resulting releases of fission products. NEK new SAMG's revision major changes are made due to: replacement of Electrical Recombiners by Passive Autocatalytic Recombiners (PARs) and the installation of Passive Containment Filtered Vent System (PCFV); to handle a fuel damage situation in Spent Fuel Pool (SFP) and to assess risk of core damage situation during shutdown operation. (authors)

Severe accident simulation at Olkiuoto

Energy Technology Data Exchange (ETDEWEB)

Tirkkonen, H.; Saarenpaeae, T. [Teollisuuden Voima Oy (TVO), Olkiluoto (Finland); Cliff Po, L.C. [Micro-Simulation Technology, Montville, NJ (United States)

1995-09-01

A personal computer-based simulator was developed for the Olkiluoto nuclear plant in Finland for training in severe accident management. The generic software PCTRAN was expanded to model the plant-specific features of the ABB Atom designed BWR including its containment over-pressure protection and filtered vent systems. Scenarios including core heat-up, hydrogen generation, core melt and vessel penetration were developed in this work. Radiation leakage paths and dose rate distribution are presented graphically for operator use in diagnosis and mitigation of accidents. Operating on an graphically for operator use in diagnosis and mitigation of accidents. Operating on an 486 DX2-66, PCTRAN-TVO achieves a speed about 15 times faster than real-time. A convenient and user-friendly graphic interface allows full interactive control. In this paper a review of the component models and verification runs are presented.

KAPOOL experiments to simulate molten corium - sacrificial concrete interaction

International Nuclear Information System (INIS)

Eppinger, B.; Fieg, G.; Tromm, W.

2001-01-01

In future Light Water Reactors special devices (core catchers) might be required to prevent containment failure by basement erosion after reactor pressure vessel melt-through during a core meltdown accident. In the planned European Pressurized Reactor (EPR) the core melt is retained in the reactor cavity for ∼ 1 h to pick up late melts after the failure of the reactor pressure vessel. The reactor cavity is protected by a layer of sacrificial concrete and closed by a melt gate at the bottom towards the spreading compartment. After erosion of the sacrificial concrete and melt-through of the gate the core melt should be distributed homogeneously into the spreading compartment. There the melt is cooled by flooding with water. The knowledge of the sacrificial concrete erosion phase in the reactor cavity is essential for the severe accident assessment. Several KAPOOL experiments have been performed to investigate the erosion of two possible compositions of sacrificial concretes using alumina-iron thermite melts as a simulant for the core melt. Erosion rates as a function of the melt temperature and the inhomogeneity of the melt front are presented in this paper. (authors)

A study of entrainment at a break and in the core during small break loss-of-coolant accidents in PWRs

International Nuclear Information System (INIS)

Yonomoto, Taisuke

1996-05-01

Objectives of the present study are to obtain a better understanding of entrainment at a break and in the core during small break loss-of-coolant-accidents (SBLOCAs) in PWRs, and to develop a means for the best evaluation of the phenomena. For the study of entrainment at a break, a theoretical model was developed, which was assessed by comparisons with several experimental data bases. By modifying a LOCA analysis code using the present model, experimental results obtained from SBLOCA experiments at a PWR large-scale simulator were reproduced very well. For the study of entrainment in the core, reflooding experiments were conducted at high pressure, from which the onset conditions were obtained. It was confirmed that the cooling behavior for a dry-out core is very simple under typical high pressure reflooding conditions for PWRs, because liquid entrainment does not occur in the core. (author)

Accident management: What is it and how do you do it?

International Nuclear Information System (INIS)

Henry, Robert E.; Hammersley, Robert J.

2004-01-01

Accident management is the composite of those actions that would prevent, stop and/or mitigate a severe accident in a nuclear power plant. Since they act to prevent core damage, the Emergency Operating Procedures (EOPs) are an integral part of accident management. Each of the Owners Groups have developed EOPs that are well thought out for instructing the operator to respond to accident conditions which could threaten the core. However, for those very low probability events in which the core could be uncovered and damaged, accident management actions arise from a logical evaluation of possible actions (strategies) for recovering from the accident state and protecting the public health and safety. To understand the character of accident management it is first necessary to define: 1. What is threatened as a result of the accident? 2. Fundamentally, what needs to be protected? 3. What is known during an accident? 4. What have we learned from the TMI-2 accident? 5. What have we learned from the plant specific IPEs? Once these subjects are reviewed on a utility specific and plant specific basis, accident management actions become relatively straightforward and likely can be effectively addressed using the total capability available in a given design. This paper discusses these five questions in a global manner with the aim being to aid plant specific implementation. (author)

Statistical inference of the nuclear accidents occurrence number for the next decade

International Nuclear Information System (INIS)

Felizia, E.R.

1987-01-01

This paper aims to give a response using the classical statistical and bayesian inference techniques regarding the common characteristic in the Harrisburg and Chernobyl nuclear accidents: in both reactors, core fusion occurred. In relation to the last mentioned techniques, the most recent developments were applied, based on the decision theory of uncertainty; among others, the principle of maximum entropy. Besides, as a preliminar information on the accidents occurrence frequency with core fusion, the German risk analysis results were used. The estimations predicted for the next decade an average between one or two accidents with core fusion and low possibilities for the 'no accident' event in the same period. (Author)

Evaluation of reflooding effects on an overheated boiling water reactor core in a small steam-line break accident using MAAP, MELCOR, and SCDAP/RELAP5 computer codes

International Nuclear Information System (INIS)

Lindholm, I.; Pekkarinen, E.; Sjoevall, H.

1995-01-01

Selected core reflooding situations were investigated in the case of a Finnish boiling water reactor with three severe accident analysis computer codes (MAAP, MELCOR, and SCDAP/RELAP5). The unmitigated base case accident scenario was a 10% steam-line break without water makeup to the reactor pressure vessel initially. The pumping of water to the core was started with the auxiliary feed water system when the maximum fuel cladding temperature reached 1,500 K. The auxiliary feedwater system pumps water (temperature 303 K) through the core spray spargers (core spray) on the top of the core and through feedwater nozzles to the downcomer (downcomer injection). The scope of the study was restricted to cases where the overheated core was still geometrically intact at the start of the reflooding. The following different core reflooding situations were investigated: (1) auxiliary feedwater injection to core spray (45 kg/s); (2) auxiliary feedwater injection to downcomer (45 kg/s); (3) auxiliary feedwater injection to downcomer (45 kg/s) and to core spray (45 kg/s); (4) no reflooding of the core. All the three codes predicted debris formation after the water addition, and in all MAAP and MELCOR reflooding results the core was quenched. The major difference between the code predictions was in the amount of H 2 produced, though the trends in H 2 production were similar. Additional steam production during the quenching process accelerated the oxidation in the unquenched parts of the core. This result is in accordance with several experimental observations

An assessment of core wide coherency effects in the multichannel modeling of the initiating phase of a severe accident in a sodium fast reactor

International Nuclear Information System (INIS)

Guyot, M.; Gubernatis, P.; Suteau, C.; Le Tellier, R.; Lecerf, J.

2014-01-01

To consolidate the safety assessment for liquid-metal fast breeder reactors (LMFBRs), hypothetical core disruptive accident (HCDA) sequences have been extensively studied over the past decades. Numerous analyses of the so called initiating phase (or primary phase) of a HCDA have been made with the safety analysis system code SAS4A. The SAS4A accident analysis code requires that subassemblies or groups of subassemblies be represented together as independent channels. For simulating a severe accident sequence, a subassembly-to-channel assignment procedure has to be implemented to produce the consistent SAS4A input decks. Generally, one uses imposed criteria over relevant reactor parameters to determine the subassembly to- channel arrangement. The multiple-assembly-per-channel approach introduces core wide coherency effects, which can affect the reactivity balance and therefore the overall accident development. In this paper, a subassembly-to channel assignment procedure based on the subassembly power-to-flow ratio is presented and implemented to generate the SAS4A input decks over a range of parameter values. The corresponding SAS4A calculations have been performed on a large LMFBR. The purpose of the present series of calculations is to investigate the magnitude of errors encountered in the analysis of the initiating phase related to the subassembly-to-channel arrangement selection, by comparison with a one-subassembly-per-channel reference solution. It appears that a refinement in the channel arrangement substantially reduces core wide coherency effects. Analysis of the calculations also suggests that an accurate representation of the scenario requires the number of channels to be on approximately the same order of magnitude as the total number of subassemblies. Numerical results are examined to provide the reader with quantitative measurements of bias related to subassembly to- channel arrangement. (authors)

Analyses of severe accident scenarios in RBMK-1500

International Nuclear Information System (INIS)

Kaliatka, A.; Rimkevicius, S.; Uspuras, E.; Urbonavicius, E.

2006-01-01

Even though research of severe accidents in light water reactors is performed around the world for several decades many questions remain. Research is mostly performed for vessel-type reactors. RBMK is a channel type light water reactor, which differs from the vessel-type reactors in several aspects. These differences impose some specifics in the accident phenomena and processes that occur during severe accidents. Severe accident research for RBMK reactors is taking first steps and very little information is available in the open literature. The existing severe accident analysis codes are developed for vessel-type reactors and their application to the analysis of accidents in RBMK is not straightforward. This paper presents the results of an analysis of large loss-of-coolant accident scenarios with loss of coolant injection to the core of RBMK-1500. The analysis performed considers processes in the reactor core, in the reactor cooling system and in the confinement until the fuel melting started. This paper does not aim to answer all the questions regarding severe accidents in RBMK but rather to start a discussion, identify the expected timing of the key phenomena. (orig.)

Severe Accident Recriticality Analyses (SARA)

Energy Technology Data Exchange (ETDEWEB)

Frid, W. [Swedish Nuclear Power Inspectorate, Stockholm (Sweden); Hoejerup, F. [Risoe National Lab. (Denmark); Lindholm, I.; Miettinen, J.; Puska, E.K. [VTT Energy, Helsinki (Finland); Nilsson, Lars [Studsvik Eco and Safety AB, Nykoeping (Sweden); Sjoevall, H. [Teoliisuuden Voima Oy (Finland)

1999-11-01

Recriticality in a BWR has been studied for a total loss of electric power accident scenario. In a BWR, the B{sub 4}C control rods would melt and relocate from the core before the fuel during core uncovery and heat-up. If electric power returns during this time-window unborated water from ECCS systems will start to reflood the partly control rod free core. Recriticality might take place for which the only mitigating mechanisms are the Doppler effect and void formation. In order to assess the impact of recriticality on reactor safety, including accident management measures, the following issues have been investigated in the SARA project: 1. the energy deposition in the fuel during super-prompt power burst, 2. the quasi steady-state reactor power following the initial power burst and 3. containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core state initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality - both superprompt power bursts and quasi steady-state power generation - for the studied range of parameters, i. e. with core uncovery and heat-up to maximum core temperatures around 1800 K and water flow rates of 45 kg/s to 2000 kg/s injected into the downcomer. Since the recriticality takes place in a small fraction of the core the power densities are high which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal/g, was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding

Severe Accident Recriticality Analyses (SARA)

International Nuclear Information System (INIS)

Frid, W.; Hoejerup, F.; Lindholm, I.; Miettinen, J.; Puska, E.K.; Nilsson, Lars; Sjoevall, H.

1999-11-01

Recriticality in a BWR has been studied for a total loss of electric power accident scenario. In a BWR, the B 4 C control rods would melt and relocate from the core before the fuel during core uncovery and heat-up. If electric power returns during this time-window unborated water from ECCS systems will start to reflood the partly control rod free core. Recriticality might take place for which the only mitigating mechanisms are the Doppler effect and void formation. In order to assess the impact of recriticality on reactor safety, including accident management measures, the following issues have been investigated in the SARA project: 1. the energy deposition in the fuel during super-prompt power burst, 2. the quasi steady-state reactor power following the initial power burst and 3. containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core state initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality - both superprompt power bursts and quasi steady-state power generation - for the studied range of parameters, i. e. with core uncovery and heat-up to maximum core temperatures around 1800 K and water flow rates of 45 kg/s to 2000 kg/s injected into the downcomer. Since the recriticality takes place in a small fraction of the core the power densities are high which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal/g, was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding

Analyses of systems availability and operator actions to support the development of severe accident procedures

International Nuclear Information System (INIS)

Lutz, R.J. Jr.; Scobel, J.H.

1989-01-01

This paper reports on traditional analyses of severe accidents, such as those presented in Probabilistic Risk Assessment (PRA) studies of nuclear power stations, that have generally been performed on the assumption that all means of cooling the reactor core are lost and that no operator actions to mitigate the consequences or progression of the severe accident are performed. The assumption to neglect the availability of safety systems and operator actions which do not prevent core melting can lead to erroneous conclusions regarding the plant severer accident profile. Recent work in severe accident management has identified the need to perform analyses which consider all systems availabilities and operator actions, irrespective of their contribution to the prevention of core melting. These new analyses indicate that the traditional analyses result in overfly pessimistic predictions of the time of core melting and the subsequent potential for recovery of core cooling prior to core melting. Additionally, since the traditional analyses do not model all of the operator actions which are prescribed, the impact of additional severe accident operator actions on the progression and consequences of the accident cannot be reliably identified. Further, the more detailed analysis can change the focus of the importance of various system to the prevention of core damage and the mitigation of severe accident consequences. Finally, the simplicity of the traditional analyses can have a considerable impact on severe accident decision making, particularly in the evaluation of alternate plant design features and the priorities for research studies

Severe accident management. Optimized guidelines and strategies

International Nuclear Information System (INIS)

Braun, Matthias; Löffler, Micha; Plank, Hermann; Asse, Dietmar; Dimmelmeier, Harald

2014-01-01

The highest priority for mitigating the consequences of a severe accident with core melt lies in securing containment integrity, as this represents the last barrier against fission product release to the environment. Containment integrity is endangered by several physical phenomena, especially highly transient phenomena following high-pressure reactor pressure vessel failure (like direct containment heating or steam explosions which can lead to early containment failure), hydrogen combustion, quasi-static over-pressure, temperature failure of penetrations, and basemat penetration by core melt. Each of these challenges can be counteracted by dedicated severe accident mitigation hardware, like dedicated primary circuit depressurization valves, hydrogen recombiners or igniters, filtered containment venting, containment cooling systems, and core melt stabilization systems (if available). However, besides their main safety function these systems often have also secondary effects that need to be considered. Filtered containment venting causes (though limited) fission product release into the environment, primary circuit depressurization leads to loss of coolant, and an ex-vessel core melt stabilization system as well as hydrogen igniters can generate high pressure and temperature loads on the containment. To ensure that during a severe accident any available systems are used to their full beneficial extent while minimizing their potential negative impact, AREVA has implemented a severe accident management for German nuclear power plants. This concept makes use of extensive numerical simulations of the entire plant, quantifying the impact of system activations (operational systems, safety systems, as well as dedicated severe accident systems) on the accident progression for various scenarios. Based on the knowledge gained, a handbook has been developed, allowing the plant operators to understand the current state of the plant (supported by computational aids), to predict

Definition of containment failure

International Nuclear Information System (INIS)

Cybulskis, P.

1982-01-01

Core meltdown accidents of the types considered in probabilistic risk assessments (PRA's) have been predicted to lead to pressures that will challenge the integrity of containment structures. Review of a number of PRA's indicates considerable variation in the predicted probability of containment failure as a function of pressure. Since the results of PRA's are sensitive to the prediction of the occurrence and the timing of containment failure, better understanding of realistic containment capabilities and a more consistent approach to the definition of containment failure pressures are required. Additionally, since the size and location of the failure can also significantly influence the prediction of reactor accident risk, further understanding of likely failure modes is required. The thresholds and modes of containment failure may not be independent

Safety-related LWR research. Annual report 1989

International Nuclear Information System (INIS)

1990-11-01

The main topics in this annual report 1989 are phenomena of heavy fuel damage and single aspects of a core meltdown accident. The examined single aspects refer to aerosol behavior and filter engineering and to methods for assessment and minimization of the radiological consequences of reactor accidents. Different contributions to selected, safety-related problems of an advanced pressurized-water reactor complete the topic spectrum. The annual report 1989 describes the progress of the research work wich was carried out in the area of safety research by institutes and departments of the KfK, and on behalf of the KfK by external institutions. The individual contributions represent the status of work at the end of the year under review, 1989. (orig./HP) [de

Dominant accident sequences in Oconee-1 pressurized water reactor

International Nuclear Information System (INIS)

Dearing, J.F.; Henninger, R.J.; Nassersharif, B.

1985-04-01

A set of dominant accident sequences in the Oconee-1 pressurized water reactor was selected using probabilistic risk analysis methods. Because some accident scenarios were similar, a subset of four accident sequences was selected to be analyzed with the Transient Reactor Analysis Code (TRAC) to further our insights into similar types of accidents. The sequences selected were loss-of-feedwater, small-small break loss-of-coolant, loss-of-feedwater-initiated transient without scram, and interfacing systems loss-of-coolant accidents. The normal plant response and the impact of equipment availability and potential operator actions were also examined. Strategies were developed for operator actions not covered in existing emergency operator guidelines and were tested using TRAC simulations to evaluate their effectiveness in preventing core uncovery and maintaining core cooling

Prevention and mitigation of severe accidents

International Nuclear Information System (INIS)

Weisshaeupl, H.

1996-01-01

For the European Pressurized water Reactor (EPR), jointly developed by French and German industry, great emphasis is laid to gain further improvement in prevention of severe accidents based on the accumulative experience and proven technology of the French and German PWR reactors. In this evolutionary development, a balanced and comprehensive approach in respect to implement new passive features has been chosen. Improvements in each step of the defense in depth concept lead to a further decrease in the probability of occurrence of a severe accident with partial or even gross melting of the core. The different phenomenons that occur during such an hypothetical accident must be taken into account during the conception of specific measurements necessary to mitigate accident consequences. To cope with the consequences of a severe accident with core melt down means to deal with different phenomena which may threaten the integrity of the containment or may lead to an enhanced fission product release into the environment: high pressure reactor pressure vessel failure; energetic molten fuel coolant interaction; direct containment heating, molten core concrete interaction; hydrogen combustion; long term pressure and temperature increase in the containment. The EPR approach follows the recommendations from the DFD (Deutsch-Franzosischer Direktionsausschuss), jointly prepared by the French and German safety authorities. The EPR concept consist to prevent or eliminate as far as possible scenarios which are connected with high loads (high pressure failure of the reactor pressure vessel, or global hydrogen detonation etc..) by dedicated design provisions, and to deal with the consequences of severe accident scenarios which are not ruled out by specific safety measures. The measures comprise: the primary system depressurization; the control of hydrogen; the stabilisation and cooling of the melted core; the containment heat removal. They are completed by specific characteristics

The management of severe accidents

International Nuclear Information System (INIS)

Pelce, J.; Brignon, P.

1987-01-01

In considering severe accidents in water power reactors, a major problem that arises is how to manage them in such a way that the situation can be controlled as well as possible, from the aspects both of preventing serious damage to the core of limiting the discharge of radioactivity. A number of countries have announced provisions in the field of accident management, some already set up, others planned, but these mainly apply to preventing damage to the core. Part of this report deals with this aspect, to show that there is a fairly wide consensus on how problems should be approached. Attitudes vary, on the other hand, in the approach to mitigate radioactive release. In fact, few countries have proposed concrete steps to manage severe accidents in the final stages when the core is seriously damaged. Since it is difficult to compare different approaches, only the French approach is described. This description is however very brief, because in the five or six years since it was defined, the approach has been presented many times. The stress is placed more on the comments which this type of approach suggests, to make the subsequent general discussion easier

Joint research project WASA-BOSS: Further development and application of severe accident codes. Assessment and optimization of accident management measures. Project B: Accident analyses for pressurized water reactors with the application of the ATHLET-CD code; Verbundprojekt WASA-BOSS: Weiterentwicklung und Anwendung von Severe Accident Codes. Bewertung und Optimierung von Stoerfallmassnahmen. Teilprojekt B: Druckwasserreaktor-Stoerfallanalysen unter Verwendung des Severe-Accident-Codes ATHLET-CD

Energy Technology Data Exchange (ETDEWEB)

Jobst, Matthias; Kliem, Soeren; Kozmenkov, Yaroslav; Wilhelm, Polina

2017-02-15

Within the framework of the project an ATHLET-CD input deck for a generic German PWR of type KONVOI has been created. This input deck was applied to the simulation of severe accidents from the accident categories station blackout (SBO) and small-break loss-of-coolant accidents (SBLOCA). The complete accident transient from initial event at full power until the damage of reactor pressure vessel (RPV) is covered and all relevant severe accident phenomena are modelled: start of core heat up, fission product release, melting of fuel and absorber material, oxidation and release of hydrogen, relocation of molten material inside the core, relocation to the lower plenum, damage and failure of the RPV. The model has been applied to the analysis of preventive and mitigative accident management measures for SBO and SBLOCA transients. Therefore, the measures primary side depressurization (PSD), injection to the primary circuit by mobile pumps and for SBLOCA the delayed injection by the cold leg hydro-accumulators have been investigated and the assumptions and start criteria of these measures have been varied. The time evolutions of the transients and time margins for the initiation of additional measures have been assessed. An uncertainty and sensitivity study has been performed for the early phase of one SBO scenario with PSD (until the start of core melt). In addition to that, a code -to-code comparison between ATHLET-CD and the severe accident code MELCOR has been carried out.

Development of high performance core for large fast breeder reactors

International Nuclear Information System (INIS)

Inoue, Kotaro; Kawashima, Katsuyuki; Watari, Yoshio.

1982-01-01

Subsequently to the fast breeder prototype reactor ''Monju'', the construction of a demonstration reactor with 1000 MWe output is planned. This research aims at the establishment of the concept of a large core with excellent fuel breeding property and safety for a demonstration and commercial reactors. For the purpose, the optimum specification of fuel design as a large core was clarified, and the new construction of a core was examined, in which a disk-shaped blanket with thin peripheral edge is introduced at the center of a core. As the result, such prospect was obtained that the time for fuel doubling would be 1/2, and the energy generated in a core collapse accident would be about 1/5 as compared with a large core using the same fuel as ''Monju''. Generally, as a core is enlarged, the rate of breeding lowers. If a worst core collapse accident occurs, the scale of accident will be very large in the case of a ''Monju'' type large core. In an unhomogeneous core, an internal blanket is provided in the core for the purpose of improving the breeding property and safety. Hitachi Ltd. developed the concept of a large core unhomogeneous in axial direction and proposed it. The research on the fuel design for a large core, an unhomogeneous core and its core collapse accident is reported. (Kako, I.)

Lack of Critical Slowing Down Suggests that Financial Meltdowns Are Not Critical Transitions, yet Rising Variability Could Signal Systemic Risk

Science.gov (United States)

Hoarau, Quentin

2016-01-01

Complex systems inspired analysis suggests a hypothesis that financial meltdowns are abrupt critical transitions that occur when the system reaches a tipping point. Theoretical and empirical studies on climatic and ecological dynamical systems have shown that approach to tipping points is preceded by a generic phenomenon called critical slowing down, i.e. an increasingly slow response of the system to perturbations. Therefore, it has been suggested that critical slowing down may be used as an early warning signal of imminent critical transitions. Whether financial markets exhibit critical slowing down prior to meltdowns remains unclear. Here, our analysis reveals that three major US (Dow Jones Index, S&P 500 and NASDAQ) and two European markets (DAX and FTSE) did not exhibit critical slowing down prior to major financial crashes over the last century. However, all markets showed strong trends of rising variability, quantified by time series variance and spectral function at low frequencies, prior to crashes. These results suggest that financial crashes are not critical transitions that occur in the vicinity of a tipping point. Using a simple model, we argue that financial crashes are likely to be stochastic transitions which can occur even when the system is far away from the tipping point. Specifically, we show that a gradually increasing strength of stochastic perturbations may have caused to abrupt transitions in the financial markets. Broadly, our results highlight the importance of stochastically driven abrupt transitions in real world scenarios. Our study offers rising variability as a precursor of financial meltdowns albeit with a limitation that they may signal false alarms. PMID:26761792

Environmental Impact Assessment following a Nuclear Accident to a Candu NPP

International Nuclear Information System (INIS)

Margeanu, C.A.; Margeanu, S.; Olteanu, Gh.

2009-01-01

The paper presents calculations of nuclear accident consequences to public and environment, for a Candu NPP using advanced fuel in two hypothetical accident scenarios: (1) large LOCA followed by partial core melting with early containment failure; (2) late core disassembly and containment bypass through ECCS. During both accidents a release occurs, radioactive contaminants being dispersed into atmosphere. As reference, estimations for Candu standard UO 2 fuel were used. The radioactive core inventory was obtained by using ORIGEN-S computer code included in ORNL,SCALE 5 programs package. Radiological consequences assessment to public and environment was performed by means of PC COSYMA computer code