Sulphate content of the Muntimpa dam water and its impact on water quality

International Nuclear Information System (INIS)

Tembo, F; Shitumbanuma, V; Simukanga, S; Mudenda, G; Chileshe, P; Mulenga, S; Phiri, Y

2004-01-01

This article presents results of a study of the quality of water from Muntimpa Dam, a reservior of waste mine water released from the processing of copper and cobalt ores by Konkola Copper Mines(KCM) Plc in Chingola. The mine water is discharged into the local Muntimpa stream, a possible source of drinking and domestic water for the local population. The purpose of the study was to determine levels of sulphate in the dam and stream water and recommend possible methods of partial sulphate removal to levels below the recommended statutory limits and secondly, to assess the impact of high sulphate levels on water quality. Study methods included the sampling of water from the Muntimpa dam and catchment area. Stream water samples were collected about 5m from the stream banks while water samples from the dam were randomly collected from the near the centre of the dam at a depth of 50cm. Laboratory methods involved the determination of physical and chemical properties of the water using standard analytical techniques. Results of the study indicate that both total (2470mg/l) and available (1965mg/l) sulphate concentrations are higher than the recommended statutory limit for the discharge of sulphates into natural streams of 1500mg/l. From the study it is concluded that water in Muntimpa dam and stream is not suitable for drinking and other domestic use due to the high sulphate levels. From theorectical considerations, it was established that sulphate reduction could be achieved by addition of lime, which however had the consquence of increasing the pH of the water in excess of the recommended Zambian statutory value of nine, and would thus require an additional process to reduce the pH. (author)

Activation of Sphalerite by Ammoniacal Copper Solution in Froth Flotation

Directory of Open Access Journals (Sweden)

Xian Xie

2016-01-01

Full Text Available The activation of sphalerite particles by ammoniacal copper solution (ACS was investigated in this study. This microflotation study was conducted on a single sphalerite mineral with the particles size of 38 μm to 75 μm. Results showed that ACS has somewhat better activation effect than copper sulphate (a traditional activator with sodium isobutyl xanthate as the collector. Agglomeration observation, contact angle measurement, and X-ray photoelectron spectroscopy measurement results of sphalerite particles verified the superiority of this new activator. Therefore, the substitution of copper sulphate with ACS would increase the separation efficiency not only in marmatite flotation but also in sphalerite flotation.

Copper complexes as 'radiation recovery' agents

International Nuclear Information System (INIS)

Sorenson, J.R.J.

1989-01-01

Copper and its compounds have been used for their remedial effects since the beginning of recorded history. As early as 3000 BC the Egyptians used copper as an antiseptic for healing wounds and to sterilise drinking water; and later, ca 1550 BC, the Ebers Papyrus reports the use of copper acetate, copper sulphate and pulverised metallic copper for the treatment of eye infections. These historical uses of copper and its compounds are particularly interesting in the light of modern evidence concerning the use of certain copper complexes for the treatment of radiation sickness and more recently as an adjunct to radiotherapy for cancer patients. (author)

Copper Powder and Chemicals: edited proceedings of a seminar

Energy Technology Data Exchange (ETDEWEB)

1980-12-01

Various papers are presented covering the following topics: Status of Copper Chemical Industry in India, Copper Powder from Industrial Wastes, Manufacture of Copper Hydroxide and High Grade Cement Copper from Low Grade Copper Ore, Manufacture of Copper Sulphate as a By-Product, Hydrometallurgical Treatments of Copper Converter and Smelter Slage for Recovering Copper and other Non-Ferrous Metals, Recovery of Copper from Dilute Solutions, Use of Copper Compounds as Fungicides in India, Copper in Animal Husbandry, and Use of Copper Powder and Chemicals for Marine Applications. The keynote paper given at the Seminar was on Conservation of Copper for Better Use.

Sulphate solubility and sulphate diffusion in oxide glasses: implications for the containment of sulphate-bearing nuclear wastes

International Nuclear Information System (INIS)

Lenoir, M.

2009-09-01

The thesis deals with sulphate solubility and sulphate diffusion in oxide glasses, in order to control sulphate incorporation and sulphate volatilization in nuclear waste glasses. It was conducted on simplified compositions, in the SiO 2 -B 2 O 3 -R 2 O (R = Li, Na, K, Cs), SiO 2 -B 2 O 3 -BaO and V 2 O 5 -B 2 O 3 -BaO systems. These compositions allowed us to study the influence of the nature of network-modifying ions (Li + , Na + , K + , Cs + or Ba 2+ ) and also of former elements (Si, B, V), on structure and properties of glasses. Sulphate volatility is studied in sodium borosilicate melts using an innovative technique of sulphate quantitation with Raman spectroscopy. This technique is useful to obtain kinetic curves of sulphate volatilization. The establishment of a model to fit these curves leads to the determination of diffusion coefficients of sulphate. These diffusion coefficients can thus be compared to diffusion coefficients of other species, determined by other techniques and presented in the literature. They are also linked to diffusion coefficients in relation with the viscosity of the melts. Concerning sulphate solubility in glasses, it depends on glass composition and on the nature of sulphate incorporated. Sulphate incorporation in alkali borosilicate glasses leads to the formation of a sulphate layer floating on top of the melt. Sulphate incorporation in barium borosilicate and boro-vanadate glasses leads to the crystallization of sulphate species inside the vitreous matrix. Moreover, sulphate solubility is higher in these glasses than in alkali borosilicates. Finally, exchanges between cations present in glasses and cations present in the sulphate phase are also studied. (author)

Bacterial Reduction Of Barium Sulphate By Sulphate-Reducing Bacteria

Directory of Open Access Journals (Sweden)

Luptáková Alena

2015-12-01

Full Text Available Acid mine drainage (AMD is a worldwide problem leading to contamination of water sources. AMD are characterized by low pH and high content of heavy metals and sulphates. The barium salts application presents one of the methods for the sulphates removing from AMD. Barium chloride, barium hydroxide and barium sulphide are used for the sulphates precipitation in the form of barium sulphate. Because of high investment costs of barium salts, barium sulphide is recycled from barium sulphate precipitates. It can be recycled by thermic or bacterial reduction of barium sulphate. The aim of our study was to verify experimentally the possibility of the bacterial transformation of BaSO4 to BaS by sulphate-reducing bacteria. Applied BaSO4 came from experiments of sulphates removal from Smolnik AMD using BaCl2.

Removal of sulphates from waste waters by sulphate-reducing bacteria

Directory of Open Access Journals (Sweden)

Luptáková Alena

2002-03-01

Full Text Available are present in almost all types of water, usually as a simple anion SO42-. The sulphates together with hydrogencarbonates and chlorides are principal anions in natural waters. In typical underground and surface waters, the concentration of sulphates is in the range from ten to hundreds milligrams per litre.Nowadays, the importance of the control of sulphate concentration in waste waters increases. According to the Slovak legislation the limit concentration of sulphates in surface and drinking waters is 250 mg.l-1 . In rivers the contents of sulphates increases mainly by the discharge of waste waters, which are coming mainly from chemical, textile, metallurgical, pharmaceutical, paper and mining industry. The concentration of sulphates in these waters is in the order of grams per litre.Many technologies for the sulphates removal from waste waters exist, including biologico-chemical processes. The principle of one of these methods is the reduction of sulphates by sulphate-reducing bacteria to hydrogen-sulphide.The objective of this work was to study the effect of initial sulphates concentration on the activity of anaerobic sulphate reducers as well as the kinetics of the anaerobic sulphate reduction. The batch reactor was used at temperature of 30°C and pH 7,5. Lactate was used as the carbon source.

The effect of an induced copper deficiency on the total plasma ...

African Journals Online (AJOL)

The effect of a copper deficiency on certain aspects of reproduction in ewes was ... induced by using the copper antagonists cadmium, calcium and sulphate. .... sodium (Na), magnesium (MG), potassium (K), blood urea nitrogen (BUN) and ...

Sulphate in Pregnancy

Directory of Open Access Journals (Sweden)

Paul A. Dawson

2015-03-01

Full Text Available Sulphate is an obligate nutrient for healthy growth and development. Sulphate conjugation (sulphonation of proteoglycans maintains the structure and function of tissues. Sulphonation also regulates the bioactivity of steroids, thyroid hormone, bile acids, catecholamines and cholecystokinin, and detoxifies certain xenobiotics and pharmacological drugs. In adults and children, sulphate is obtained from the diet and from the intracellular metabolism of sulphur-containing amino acids. Dietary sulphate intake can vary greatly and is dependent on the type of food consumed and source of drinking water. Once ingested, sulphate is absorbed into circulation where its level is maintained at approximately 300 μmol/L, making sulphate the fourth most abundant anion in plasma. In pregnant women, circulating sulphate concentrations increase by twofold with levels peaking in late gestation. This increased sulphataemia, which is mediated by up-regulation of sulphate reabsorption in the maternal kidneys, provides a reservoir of sulphate to meet the gestational needs of the developing foetus. The foetus has negligible capacity to generate sulphate and thereby, is completely reliant on sulphate supply from the maternal circulation. Maternal hyposulphataemia leads to foetal sulphate deficiency and late gestational foetal death in mice. In humans, reduced sulphonation capacity has been linked to skeletal dysplasias, ranging from the mildest form, multiple epiphyseal dysplasia, to achondrogenesis Type IB, which results in severe skeletal underdevelopment and death in utero or shortly after birth. Despite being essential for numerous cellular and metabolic functions, the nutrient sulphate is largely unappreciated in clinical settings. This article will review the physiological roles and regulation of sulphate during pregnancy, with a particular focus on animal models of disturbed sulphate homeostasis and links to human pathophysiology.

Coupled Transport/Reaction Modelling of Copper Canister Corrosion Aided by Microbial Processes

Energy Technology Data Exchange (ETDEWEB)

Liu, Jinsong [Royal Institute of Technology, Stockholm (Sweden). Dept. of Chemical Engineering and Technology

2006-04-15

Copper canister corrosion is an important issue in the concept of a nuclear fuel repository. Previous studies indicate that the oxygen-free copper canister could hold its integrity for more than 100,000 years in the repository environment. Microbial processes may reduce sulphate to sulphide and considerably increase the amount of sulphides available for corrosion. In this paper, a coupled transport/reaction model is developed to account for the transport of chemical species produced by microbial processes. The corroding agents like sulphide would come not only from the groundwater flowing in a fracture that intersects the canister, but also from the reduction of sulphate near the canister. The reaction of sulphate-reducing bacteria and the transport of sulphide in the bentonite buffer are included in the model. The depth of copper canister corrosion is calculated by the model. With representative 'central values' of the concentrations of sulphate and methane at repository depth at different sites in Fennoscandian Shield the corrosion depth predicted by the model is a few millimetres during 10{sup 5} years. As the concentrations of sulphate and methane are extremely site-specific and future climate changes may significantly influence the groundwater compositions at potential repository sites, sensitivity analyses have been conducted. With a broad perspective of the measured concentrations at different sites in Sweden and in Finland, and some possible mechanisms (like the glacial meltwater intrusion and interglacial seawater intrusion) that may introduce more sulphate into the groundwater at intermediate depths during future climate changes, higher concentrations of either/both sulphate and methane than what is used as the representative 'central' values would be possible. In worst cases. locally, half of the canister thickness could possibly be corroded within 10{sup 5} years.

Coupled Transport/Reaction Modelling of Copper Canister Corrosion Aided by Microbial Processes

International Nuclear Information System (INIS)

Jinsong Liu

2006-04-01

Copper canister corrosion is an important issue in the concept of a nuclear fuel repository. Previous studies indicate that the oxygen-free copper canister could hold its integrity for more than 100,000 years in the repository environment. Microbial processes may reduce sulphate to sulphide and considerably increase the amount of sulphides available for corrosion. In this paper, a coupled transport/reaction model is developed to account for the transport of chemical species produced by microbial processes. The corroding agents like sulphide would come not only from the groundwater flowing in a fracture that intersects the canister, but also from the reduction of sulphate near the canister. The reaction of sulphate-reducing bacteria and the transport of sulphide in the bentonite buffer are included in the model. The depth of copper canister corrosion is calculated by the model. With representative 'central values' of the concentrations of sulphate and methane at repository depth at different sites in Fennoscandian Shield the corrosion depth predicted by the model is a few millimetres during 10 5 years. As the concentrations of sulphate and methane are extremely site-specific and future climate changes may significantly influence the groundwater compositions at potential repository sites, sensitivity analyses have been conducted. With a broad perspective of the measured concentrations at different sites in Sweden and in Finland, and some possible mechanisms (like the glacial meltwater intrusion and interglacial seawater intrusion) that may introduce more sulphate into the groundwater at intermediate depths during future climate changes, higher concentrations of either/both sulphate and methane than what is used as the representative 'central' values would be possible. In worst cases. locally, half of the canister thickness could possibly be corroded within 10 5 years

Coupled Transport/Reaction Modelling of Copper Canister Corrosion Aided by Microbial Processes

Energy Technology Data Exchange (ETDEWEB)

Jinsong Liu [Royal Institute of Technology, Stockholm (Sweden). Dept. of Chemical Engineering and Technology

2006-04-15

Copper canister corrosion is an important issue in the concept of a nuclear fuel repository. Previous studies indicate that the oxygen-free copper canister could hold its integrity for more than 100,000 years in the repository environment. Microbial processes may reduce sulphate to sulphide and considerably increase the amount of sulphides available for corrosion. In this paper, a coupled transport/reaction model is developed to account for the transport of chemical species produced by microbial processes. The corroding agents like sulphide would come not only from the groundwater flowing in a fracture that intersects the canister, but also from the reduction of sulphate near the canister. The reaction of sulphate-reducing bacteria and the transport of sulphide in the bentonite buffer are included in the model. The depth of copper canister corrosion is calculated by the model. With representative 'central values' of the concentrations of sulphate and methane at repository depth at different sites in Fennoscandian Shield the corrosion depth predicted by the model is a few millimetres during 10{sup 5} years. As the concentrations of sulphate and methane are extremely site-specific and future climate changes may significantly influence the groundwater compositions at potential repository sites, sensitivity analyses have been conducted. With a broad perspective of the measured concentrations at different sites in Sweden and in Finland, and some possible mechanisms (like the glacial meltwater intrusion and interglacial seawater intrusion) that may introduce more sulphate into the groundwater at intermediate depths during future climate changes, higher concentrations of either/both sulphate and methane than what is used as the representative 'central' values would be possible. In worst cases. locally, half of the canister thickness could possibly be corroded within 10{sup 5} years.

Effect of dietary organic and inorganic copper supplement on ...

African Journals Online (AJOL)

The effect of dietary copper source and dosage on growth, apparent nutrient digestibility, trace mineral retention, ileal morphology and blood parameters of cockerel chicks were investigated using two hundred and forty (240) day-old chicks arranged in a 2 × 3 factorial arrangements involving 2 Cu sources (copper sulphate ...

Yield of castor bean fertilized with sewage sludge and potassium and magnesium sulphate

Directory of Open Access Journals (Sweden)

Thâmara F. M. Cavalcanti

2015-08-01

Full Text Available ABSTRACTThe aim of this study was to evaluate the yield and nutrition of castor bean in response to fertilization with sewage sludge and potassium (K and magnesium (Mg sulphate. The experiment was carried out from January to July 2011. The treatments, in a randomized block design with three replicates, in a Nitosol, corresponded to a factorial scheme (2 x 4 +1: two doses of K and Mg sulphate combined with four doses of sewage sludge (0, 2.60, 5.20 and 10.40 t ha-1, dry basis, applied based on its nitrogen (N content and the N requirement for the crop and an additional treatment with NPK. The castor bean grain yield fertilized with sewage sludge did not differ from conventional fertilization, with the maximum value achieved at a dose of 7.5 t ha-1 of sewage sludge. The fertilization with sewage sludge increased zinc and copper levels in the soil to values close to or higher than those in conventional fertilization, without any influence on the concentrations in the leaf. Fertilization with K and Mg sulphate increased the levels of these cations in the soil without affecting the concentrations in the leaves. The fertilization with sewage sludge increased the contents of organic matter, sulfur, zinc, iron, copper and boron in the soil, and manganese and boron in castor bean leaves.

Effects of in vitro copper sulphate supplementation on the ejaculated sperm characteristics in water buff aloes ( Bubalus bubalis

Directory of Open Access Journals (Sweden)

Mehdi Tabassomi

2013-03-01

Full Text Available This study was carried out to investigate effects of copper sulphate (CuSO4 additive tosemen extenders on sperm parameters:progressive motility, viability, membrane integrityand DNA damage, after semen dilution and cryopreservation. Semen samples of 5 buffalobulls of 3-5 years old were collected at 5 different occasions during the autumn 2011. A totalnumber of 25 samples were used in each examination. Sperm progressive motility andviability were measured at 0 (T0, 60 (T1 and 120 (T2 min after diluting semen in tris-citricacid extender containing 0 (control, 0.004, 0.008, 0.016, 0.032 and 0.064 mg L-1CuSO4. Later,semen was diluted in a tris-citric acid-egg yolk-glycerol extender containing the sameamounts ofCuSO4, cooled to 4̊C and kept refrigerated for 4 hr to equilibrate, spermprogressive motility, viability, membrane integrity and DNA damage were estimated. Then,semen was packed in 0.5 mL French straws and frozen in liquid nitrogen. Later, the frozensemen was thawed in 37 ̊C water bath for 30 sec, and the same parameters as well as totalantioxidant capacity (TAC of the frozen-thawed semen were estimated. The results showedthat copper additive at the rate of 0.032 mg L-1gives a better protection of sperms throughthe process of dilution, equilibration and freeze-thawing than that in control and other Cuconcentrations, while 0.064 mg L-1CuSO4had deleterious effect on the sperm.

Isotopic evolution of aqueous sulphate in northern Chile water

International Nuclear Information System (INIS)

Aravena, R.; Suzuki, O.; Fritz, P.; Pena, H.; Rauert, W.

1987-01-01

deposits in the Salares provides strong indication that groundwater sulphate was their precursor. The enriched values of the springs' sulphate suggest that oxidation of sulphide minerals is not the main source of the sulphate in the recharge area. The isotope content of the aqueous sulphate in these water could be generated by an input of marine sulphate of Permian age. However, the rocks in this area are mainly igneous and volcanic. A more likely sulphur source are sulphate minerals associated with sulphide minerals in these terrains. For example the sulphate in porphyry copper deposits, which ate abundant in the Chilean Andes, shows an isotope content between +6.8 per mille and +8.5 per mille for 18 O and +8.6 per mille and + 15.5 per mille for 34 S. In conclusion, the sulphate in the Pampa and Llamara water is probably of hydrothermal-magmatic and/or volcanic origin. It has been proposed that the 18 O isotope exchange between water and sulphate could be used as an age indicator. However, comparison of radiocarbon data in groundwater with the parameter 18 O sulphate - 18 O water does not show any correlation and, therefore, no age information can be deducted based on the 18 O evolution of the sulphate. (author)

Assessment of strains of Pseudomonas syringae pv. tomato from Tanzania for resistance to copper and streptomycin

DEFF Research Database (Denmark)

Shenge, K.C.; Wydra, K.; Mabagala, M.B.

2008-01-01

Fifty-six strains of Pseudomonas syringae pv. tomato (P.s. pv. tomato) were collected from tomato-producing areas in Tanzania and assessed for resistance to copper and antibiotics. The collection was done from three tomato-producing regions (Morogoro, Arusha and Iringa), representing three...... different ecological conditions in the country. After isolation and identification, the P. s. pv. tomato strains were grown on King's medium B (KB) amended with 20% copper sulphate (w/v). The strains were also assessed for resistance to antibiotics. Results indicated that there was widespread resistance...... strains of the pathogen were moderately resistant to copper sulphate, such that 54.0% of them were able to grow on the KB medium amended with 20% (w/v) of the copper compound....

The Effect of Copper

African Journals Online (AJOL)

environment, where fishes are found, stuns them ... of earthen ponds are springing up near cocoa ... farm, which posses toxicological risk to farmed ... Veg. oil. 1.0. 1.0. 1.0. 1.0. 1.0. Copper sulphate 0. 1.0. 2.5. 5.0. 7.5. Total ..... Cellulase Production by Wild Strains of Aspergillus Niger, ... Mangrove Area of Lagos, Nigeria.

A novel polymeric leveller for the electrodeposition of copper from acidic sulphate bath: A spectroelectrochemical investigation

International Nuclear Information System (INIS)

Bozzini, Benedetto; D'Urzo, Lucia; Mele, Claudio

2007-01-01

The electrodeposition of copper has recently become a 'hot topic' due to its extensive application to the fabrication of interconnects in the integrated circuits (IC) manufacturing process. However, the proper composition of the electrochemical deposition (ECD) bath, and in particular the selection of the levelling agent, represents one of the crucial factors for an effective transition of Cu ECD towards the most advanced technology nodes. In this paper we report on the electrodeposition of Cu from acidic sulphate baths containing a potential innovative polymeric leveller: a benzyl-phenyl modified polyethyleneimine (BPPEI). This investigation was carried out by: (i) cyclic voltammetry (CV) at a rotating-disk electrode, (ii) in situ surface-enhanced Raman spectroscopy (SERS) during electrodeposition and (iii) scanning electron microscopy (SEM). CV results show that BPPEI acts as an inhibitor of the electrodeposition process, since it reduces the exchange current density and increases the cathodic Tafel slope. Mass transport limitations to the Cu(II) reduction process are essentially unaffected by the presence of BPPEI. SERS spectra show that BPPEI is adsorbed at the growing Cu cathode at all potentials of interest for electroplating. SEM micrographs prove that BPPEI acts as an efficient grain-refiner and suppressor of unstable 3D growth. Cathodic reactivity of BPPEI was proved by the analysis of CV features and potential-dependent SERS spectral changes

The Reclamation of Industrial Wastes Inclusive Sulphates by Sulphate-Reducing Bacteria

Directory of Open Access Journals (Sweden)

Mária Kušnierová

2004-12-01

Full Text Available The objective of our study was to verify experimentally the possibility of using coal mine drainage and gypsum from the „stabilizate“ (the final product from the combustion desulphurisation as the source of sulphate for the cultivation of SRB with the prospect of: purging of mine waste waters inclusive sulphates, recycling of desulphurisation agent (limestone and production of elemental sulphur from hydrogen sulphide. The results confirmed the theoretical assumptions on the use of gypsum, which forms the substantial component of „stabilizate“, as the source of sulphate for sulphate-reducing bacteria, which produce hydrogen sulphide in the process of bacterial reduction of sulphates. They also showed the possibility of recycling the desulphurisation agent – limestone, as well as the realistic alternative of using „stabilizate“ in the production of elemental sulphur which still represents an important raw material needed in chemical, paper or other industries.

Sodium diethyldithiocarbamate as accelerator of the rate of copper cementation

Directory of Open Access Journals (Sweden)

Abeer A. El-Saharty

2015-12-01

Full Text Available The effects of Cu2+ ion concentration and temperature on the cementation rate of copper from copper sulphate on zinc and the effect of additives of the organic compound “sodium diethyldithiocarbamate” (NaDDC were studied. It was noticed that the cementation increases significantly by increasing the concentrations of NaDDC. The rate of cementation increased by 58.58−100.31%. Our data showed that sodium diethyldithiocarbamate reacts with the Cu2+ solution giving a complex of copper diethyldithiocarbamate, which enhances the rate of cementation.

Patterned electrochemical deposition of copper using an electron beam

Directory of Open Access Journals (Sweden)

Mark den Heijer

2014-02-01

Full Text Available We describe a technique for patterning clusters of metal using electrochemical deposition. By operating an electrochemical cell in the transmission electron microscope, we deposit Cu on Au under potentiostatic conditions. For acidified copper sulphate electrolytes, nucleation occurs uniformly over the electrode. However, when chloride ions are added there is a range of applied potentials over which nucleation occurs only in areas irradiated by the electron beam. By scanning the beam we control nucleation to form patterns of deposited copper. We discuss the mechanism for this effect in terms of electron beam-induced reactions with copper chloride, and consider possible applications.

Concentration of copper in muscles, liver, hair and feaces of growing rabbits fed diet supplemented with copper sulphate

Czech Academy of Sciences Publication Activity Database

Marounek, Milan; Skřivanová, V.; Volek, Z.; Březina, P.

2002-01-01

Roč. 10, č. 4 (2002), s. 167-170 ISSN 1257-5011 R&D Projects: GA AV ČR KSK5020115 Grant - others:GA NATO(XX) MO2-99-04 Keywords : copper retention * mineral metabolism * copper supplementation Subject RIV: FB - Endocrinology, Diabetology, Metabolism, Nutrition

Synthesis of Copper Nanoparticles in Ethylene Glycol by Chemical Reduction with Vanadium (+2 Salts

Directory of Open Access Journals (Sweden)

Andrea Pietro Reverberi

2016-09-01

Full Text Available Copper nanoparticles have been synthesized in ethylene glycol (EG using copper sulphate as a precursor and vanadium sulfate as an atypical reductant being active at room temperature. We have described a technique for a relatively simple preparation of such a reagent, which has been electrolytically produced without using standard procedures requiring an inert atmosphere and a mercury cathode. Several stabilizing agents have been tested and cationic capping agents have been discarded owing to the formation of complex compounds with copper ions leading to insoluble phases contaminating the metallic nanoparticles. The elemental copper nanoparticles, stabilized with polyvinylpyrrolidone (PVP and sodium dodecyl sulphate (SDS, have been characterized for composition by energy dispersive X-ray spectroscopy (EDS, and for size by dynamic light scattering (DLS, and transmission electron microscopy (TEM, giving a size distribution in the range of 40–50 nm for both stabilizing agents. From a methodological point of view, the process described here may represent an alternative to other wet-chemical techniques for metal nanoparticle synthesis in non-aqueous media based on conventional organic or inorganic reductants.

[Biohydrometallurgical technology of a complex copper concentrate process].

Science.gov (United States)

Murav'ev, M I; Fomchenko, N V; Kondrat'eva, T F

2011-01-01

Leaching of sulfide-oxidized copper concentrate of the Udokan deposit ore with a copper content of 37.4% was studied. In the course of treatment in a sulfuric acid solution with pH 1.2, a copper leaching rate was 6.9 g/kg h for 22 h, which allowed extraction of 40.6% of copper. As a result of subsequent chemical leaching at 80 degrees C during 7 h with a solution of sulphate ferric iron obtained after bio-oxidation by an association of microorganisms, the rate of copper recovery was 52.7 g/kg h. The total copper recovery was 94.5% (over 29 h). Regeneration of the Fe3+ ions was carried out by an association of moderately thermophilic microorganisms, including bacteria of genus Sulfobacillus and archaea of genus Ferroplasma acidiphilum, at 1.0 g/l h at 40 degrees C in the presence of 3% solids obtained by chemical leaching of copper concentrate. A technological scheme of a complex copper concentrate process with the use of bacterial-chemical leaching is proposed.

Development and validation of a behavioural assay to measure the tolerance of Hediste diversicolor to copper

International Nuclear Information System (INIS)

Burlinson, Frazer C.; Lawrence, Andrew J.

2007-01-01

The behaviour of Hediste diversicolor from the Humber was investigated under different concentrations of copper sulphate. A range of behaviours were indicative of metal-stress. These included consistent attempts at burrowing, eversion of the proboscis and abnormal crawling. The bioassay itself consisted of exposing worms to increasing concentrations of copper sulphate and recording the concentration at which a stress response was elicited. The behavioural end-points were shown to be a good predictor of time of death of Fal estuary worms under acutely toxic conditions. The bioassay would therefore allow the separation of tolerance phenotypes without mortality to the worm. Worms were not affected by consecutive bioassays and it was proposed that tolerance to more than one metal could be determined for individual worms. - A non-destructive behavioural bioassay is developed to determine the copper tolerance of ragworms

Adsorption of some heavy metals on sulphate and phosphate modified kaolinite clay

International Nuclear Information System (INIS)

Adebowale, K.O.; Unuabonah, I.E.; Olu-Owolabi, B.I.

2003-12-01

Kaolinite clay, in bright white lumps collected from from Ubulu-Ukwu, Delta State, Nigeria, was modified with 200μ.ml -1 of phosphate and sulphate anion and thereafter used to adsorb some heavy metals viz. lead (Pb), Cadmium (Cd), Zinc (Zn) and Copper (Cu) from aqueous solution of the metals. The metal ions showed the greatest affinity for the P-modified (P-mod) sorbents. The order of adsorption of P-mod follows the order: P-mod Pb > P-mod Cu > P-mod Zn > P-mod Cd . Desorption studies showed that the P-modified sorbents exhibited a very strong ability to specifically adsorb lead, copper and zinc and are therefore poorly desorbed. All the metals were easily desorbed from the unmodified sorbent. The potential of the modified sorbents are enumerated. (author)

Corrosion of copper alloys in sulphide containing district heting systems

DEFF Research Database (Denmark)

Thorarinsdottir, R.I.; Maahn, Ernst Emanuel

1999-01-01

Copper and some copper alloys are prone to corrosion in sulphide containing geothermal water analogous to corrosion observed in district heating systems containing sulphide due to sulphate reducing bacteria. In order to study the corrosion of copper alloys under practical conditions a test...... was carried out at four sites in the Reykjavik District Heating System. The geothermal water chemistry is different at each site. The corrosion rate and the amount and chemical composition of deposits on weight loss coupons of six different copper alloys are described after exposure of 12 and 18 months......, respectively. Some major differences in scaling composition and the degree of corrosion attack are observed between alloys and water types....

Sulphate in Liquid Nuclear Waste: from Production to Containment

Energy Technology Data Exchange (ETDEWEB)

Lenoir, M.; Grandjean, A.; Ledieu, A.; Dussossoy, J.L.; Cau Dit Coumes, C.; Barre, Y.; Tronche, E. [CEA Marcoule, DEN/DTCD/SECM/LDMC, Batiment 208 BP17171, Bagnols sur Ceze, 30207 (France)

2009-06-15

Nuclear industry produces a wide range of low and intermediate level liquid radioactive wastes which can include different radionuclides such as {sup 90}Sr. In La Hague reprocessing plant and in the nuclear research centers of CEA (Commissariat a l'Energie Atomique), the coprecipitation of strontium with barium sulphate is the technique used to treat selectively these contaminated streams with the best efficiency. After the decontamination process, low and intermediate level activity wastes incorporating significant quantities of sulphate are obtained. The challenge is to find a matrix easy to form and with a good chemical durability which is able to confine this kind of nuclear waste. The current process used to contain sulphate-rich nuclear wastes is bituminization. However, in order to improve properties of containment matrices and simplify the process, CEA has chosen to supervise researches on other materials such as cements or glasses. Indeed, cements are widely used for the immobilization of a variety of wastes (low and intermediate level wastes) and they may be an alternative matrix to bitumen. Even if Portland cement, which is extensively used in the nuclear industry, presents some disadvantages for the containment of sulphate-rich nuclear wastes (risk of swelling and cracking due to delayed ettringite formation), other cement systems, such as calcium sulfo-aluminate binders, may be valuable candidates. Another matrix to confine sulphate-rich waste could be the glass. One of the advantages of this material is that it could also immobilize sulphate containing high level nuclear waste which is present in some countries. This waste comes from the use of ferrous sulfamate as a reducing agent for the conversion of Pu{sup 4+} to Pu{sup 3+} in the partitioning stage of the actinides during reprocessing. Sulphate solubility in borosilicate glasses has already been studied in CEA at laboratory and pilot scales. At a pilot scale, low level liquid waste has been

Sulphonated metal phthalocyanine complexes as redox indicators in micro titrations with cerium(IV) sulphate

Energy Technology Data Exchange (ETDEWEB)

Gowda, H S; Achar, B N [Mysore Univ. (India). Dept. of Chemistry

1980-01-01

Tetrasodium salts of copper(II) 4,4', 4'', 4'''-tetrasulphophthalocyanine 2-hydrate, nickel(II) 4,4', 4'', 4'''-tetrasulphophthalocyanine, nickel(II) 3,3', 3'', 3'''-tetrasulphophthalocyanine and cobalt(II) 4,4', 4'', 4'''-tetrasulphophthalocyanine 2-hydrate, and copper phthalocyanine trisulphonic acid are prepared in pure state. The molar absorptivity and formal redox potentials of the complexes are determined. The complexes are proposed as sensitive redox indicators in the micro determination of iron(II), arsenic(III), molybdenum(V), uranium(IV) and hydroquinone with 0.001-0.0005N cerium(IV) sulphate in sulphuric, hydrochloric and acetic acid media. They give sharp colour change from light turquoise blue to pale purple colour at the equivalence point. They have advantages over a few existing redox indicators.

Quantitation and identification of methanogens and sulphate reducers in Olkiluoto groundwater

International Nuclear Information System (INIS)

Bomberg, M.; Nyyssoenen, M.; Itaevaara, M.

2010-08-01

The GEOFUNC Project focuses on the microbiology connected to safety and risk assessment of the final disposal of high radioactive nuclear waste. Methanogenic archaea and sulphate reducing bacteria are significant groups of microorganisms in anaerobic environments, and are of crucial concern for the safe long term storage of nuclear waste in deep bedrock. The sulphate reducing bacteria are able to produce sulphide which may cause corrosion of the copper in the radioactive waste storage capsules. Methanogens, on the other hand, may produce quantities of methane from various organic carbon compounds, CO 2 and H 2 . Methane may both serve as carbon source for methanotrophic microbial groups, and may also cause mobilization of radionuclides, as a result of gas discharge through fractures in the bedrock. The transition zones between the sulphate rich and methane rich waters are locations for microbial processes where the methane may serve as carbon source for sulphate reducing bacteria, which in turn would produce corrosive sulphides. It has been estimated that only 1-10 % of all the microorganisms present in the environment can be isolated and cultivated. Uncultured microorganisms can be identified and their numbers in the environment quantified by identification of specific marker genes that are essential for their functions by use of molecular methods. Methanogens, for example, can be identified by their genes for methyl coenzyme M reductase (mcrA), which is an essential enzyme involved in the production of methane. The mcrA is specifically present only in methanogenic archaea. Sulphate reducers are identified by their dissimilatory sulphite reductase genes (dsrB), which are present in and essential for all microorganisms performing dissimilatory sulphate reducing. In the GEOFUNC project, a quantitative PCR method (qPCR) was developed for the detection of methanogens and sulphate reducers. This method is based on specific quantitative detection of marker genes

THE ROLE OF PIPE AGEING IN COPPER CORROSION BY-PRODUCT RELEASE

Science.gov (United States)

The presence of sulphate, bicarbonate and orthophosphate can change the type of solid present in systems containing cupric ion or cupric hydroxide solids. In some cases, a short-term reduction in copper solubility is realized, but over longer periods of time formation of basic c...

Characterization of copper toxicity in letttuce seedlings

Energy Technology Data Exchange (ETDEWEB)

Mukherji, S; Gupta, B D

1972-01-01

Information on the effects of toxic concentration of cupric sulphate on the growth of lettuce (Lactuca sativa) seedlings is provided. Root growth is completely inhibited at 5 x 10/sup -2/ M and germination stops altogether at 10/sup -1/ M. The relative inhibition of root growth is stronger than that of hypocotyl growth. Various metabolites and hormones are partially capable of relieving copper inhibition. Catalase, peroxidase and IAA-oxidase activity shows increments directly proportional to the concentration of copper. It is obvious that growth is inversely proportional to enzyme activity. The increased level of these enzymes is probably due to an accelerated protein synthesis.

The effect of surfactants on the electropolishing behavior of copper in orthophosphoric acid

Energy Technology Data Exchange (ETDEWEB)

Taha, A.A., E-mail: asia_taha@yahoo.com; Ahmed, A.M.; Rahman, H.H. Abdel; Abouzeid, F.M.

2013-07-15

The electropolishing behavior of copper was studied in orthophosphoric acid with Triton X-100, sodium dodecyl sulphate and cetyl pyridinium chloride as additives for improving the finish obtained on copper surface. This was investigated by measuring and comparing anode potential-limiting current relationships in solutions of gradually increasing concentration of surfactants. The addition of surfactants to the electropolishing solution results in a lower limiting current. This confirms the mass transport of dissolved species from the anode surface to the bulk of solution as the rate-determining step in the presence of three surfactants in all concentrations investigated. Scanning electron microscope (SEM), atomic force microscope (AFM) and measured brightness values were used to investigate the copper surface after electropolishing and the results were compared to polishing done in absence of surfactants. According to SEM images and brightness values, addition of Triton X-100 was effective to enhance levelling and brightening more than sodium dodecyl sulphate and cetyl pyridinium chloride. AFM analysis showed that the roughness values (R{sub a}) for an electropolished copper surface, in presence of surfactants, is significantly lower than in absence of surfactants. Different reaction conditions and the physical properties of solutions are studied to obtain dimensionless correlation among all these parameters.

Modelling copper solvent extraction from acidic sulphate solutions using MOC 45

Directory of Open Access Journals (Sweden)

Alguacil, F. J.

1998-05-01

Full Text Available A mathematical model to predict the extraction has been developed for the Cu-MOC 45 system. The model consists of sets of nonlinear mass action and mass balance equations where the dimerization of the oxime was also considered. The predictive model calculated the equilibrium concentrations from the total oxime concentration, total copper concentration, initial pH value and the O/A volume phase ratio. The model suggests that the extraction of copper can be defined by the existence of two species into the organic solution: CuR₂ (k^ext = 4.2 and Cu(HR₂₂ (k^ext = 10.000- The initial oxime concentration defines the predominancy in the organic solution of both species. The model can be used to predict copper extraction isotherm as well as copper stripping with sulphuric acid.

Se desarrolla un modelo matemático para predecir el proceso de extracción en el sistema Cu-MOC 45. El modelo consiste en un conjunto de ecuaciones en el que se considera la dimerización de la oxima. El modelo permite predecir la extracción a partir de las concentraciones totales de la oxima y del cobre, del pH inicial y de la relación de fases O/A. La extracción de cobre responde a la existencia de dos especies en la fase orgánica: CuR₂ (k^ext = 4,2 y Cu(HR₂₂ (k^ext = 10.000. La predominancia de una u otra especie en esta fase depende de la concentración inicial de la oxima. El modelo también puede predecir las isotermas de extracción y la reextracción de cobre mediante ácido sulfúrico.

Sulphate removal from sodium sulphate-rich brine and recovery of barium as a barium salt mixture.

Science.gov (United States)

Vadapalli, Viswanath R K; Zvimba, John N; Mulopo, Jean; Motaung, Solly

2013-01-01

Sulphate removal from sodium sulphate-rich brine using barium hydroxide and recovery of the barium salts has been investigated. The sodium sulphate-rich brine treated with different dosages of barium hydroxide to precipitate barium sulphate showed sulphate removal from 13.5 g/L to less than 400 mg/L over 60 min using a barium to sulphate molar ratio of 1.1. The thermal conversion of precipitated barium sulphate to barium sulphide achieved a conversion yield of 85% using coal as both a reducing agent and an energy source. The recovery of a pure mixture of barium salts from barium sulphide, which involved dissolution of barium sulphide and reaction with ammonium hydroxide resulted in recovery of a mixture of barium carbonate (62%) and barium hydroxide (38%), which is a critical input raw material for barium salts based acid mine drainage (AMD) desalination technologies. Under alkaline conditions of this barium salt mixture recovery process, ammonia gas is given off, while hydrogen sulfide is retained in solution as bisulfide species, and this provides basis for ammonium hydroxide separation and recovery for reuse, with hydrogen sulfide also recoverable for further industrial applications such as sulfur production by subsequent stripping.

Grape berry bacterial inhibition by different copper fungicides

Directory of Open Access Journals (Sweden)

Martins Guilherme

2016-01-01

Full Text Available Copper fungicides are widely used in viticulture. Due to its large spectrum of action, copper provides an efficient control over a great number of vine pathogens. Previous studies showed that, high levels of cupric residues can impact grape-berry microbiota, in terms of the size and population structure, reducing the diversity and the abundance. Due to the importance of grape-berry bacterial in crop health, and the potential impact of copper fungicides over the microbiota, we determined Minimum Inhibitory Concentration (MIC of different copper formulations for bacterial species isolated from grape berries. We study the Minimum Inhibitory Concentration (MIC of different copper formulations (copper sulphate (CuSO4 pure, Bordeaux mixture (CuSO4 + Ca(OH2, copper oxide (Cu2O, copper hydroxide (Cu(OH2 over 92 bacterial strains isolated from grape berries in different stages of the ripening process. The results of MIC measurements revealed that the different copper formulations have a variable inhibitory effect and among the different isolates, some species are the most resistant to all copper formulations than others. This study confirm that usage of cupric phytosanitary products should be reasonable independently of the farming system; they also provide evidence of the importance of the choice of which copper formulations are to be used regarding their impact on the grape berry bacterial microbiota.

Effects of copper-based compounds, antibiotics and a plant activator on population sizes and spread of Clavibacter michiganensis subsp. michiganensis in greenhouse tomato seedlings

OpenAIRE

Milijašević Svetlana; Todorović Biljana; Potočnik Ivana; Rekanović Emil; Stepanović Miloš

2009-01-01

Three copper-based compounds (copper hydroxide, copper oxychloride, copper sulphate), two antibiotics (streptomycin and kasugamycin) and a plant activator (ASM) significantly reduced population sizes and spread of C. michiganensis subsp. michiganensis among tomato seedlings in the greenhouse. Streptomycin had the best effect in reducing pathogen population size in all sampling regions. Moreover, this antibiotic completely stopped the spread of C. michiganensis subsp. michiganensis in the regi...

Sulphate reduction in the Aespoe HRL tunnel

International Nuclear Information System (INIS)

Gustafson, G.; Pedersen, K.; Tullborg, E.L.; Wallin, B.; Wikberg, P.

1995-12-01

Evidence and indications of sulphate reduction based on geological, hydrogeological, groundwater, isotope and microbial data gathered in and around the Aespoe Hard Rock Laboratory tunnel have been evaluated. This integrated investigation showed that sulphate reduction had taken place in the past but is most likely also an ongoing process. Anaerobic sulphate-reducing bacteria can live in marine sediments, in the tunnel sections under the sea and in deep groundwaters, since there is no access to oxygen. The sulphate-reducing bacteria seem to thrive when the Cl - concentration of the groundwater is 4000-6000 mg/l. Sulphate reduction is an in situ process but the resulting hydrogen-sulphide rich water can be transported to other locations. A more vigorous sulphate reduction takes place when the organic content in the groundwater is high (>10 mg/l DOC) which is the case in the sediments and in the groundwaters under the sea. Some bacteria use hydrogen as an electron donor instead of organic carbon and can therefore live in deep environments where access to organic material is limited. The sulphate-reducing bacteria seem to adapt to changing flow situations caused by the tunnel construction relatively fast. Sulphate reduction seems to have occurred and will probably occur where conditions are favourable for the sulphate-reducing bacteria such as anaerobic brackish groundwater with dissolved sulphate and organic carbon or hydrogen. 59 refs, 37 figs, 6 tabs

Acute Toxicity and the Effects of Copper Sulphate (CuSO4.5H2O on the Behavior of the Black Fish (Capoeta Fusca

Directory of Open Access Journals (Sweden)

Iman Zarei

2013-02-01

Full Text Available Background: The development of toxicity tests regarding toxic responses of different fish species could be more effectively used in predictive toxicology and risk assessment. In this study lethal concentrations (LC50-96 h values of copper sulphate; an important toxic industrial pollutant, on Capoeta fusca were determined. Behavioral changes at different concentrations of CuSO4 were determined for the C.fusca. Methods: The sample fishes were collected from Qanat in Birjand and were transported to the laboratory in polythene bags. The exposure time of fish to CuSO4 was 96 hours. Mortalities were recorded at 24, 48, 72, and 96 hours of exposure, and the dead fish were removed regularly from the test aquariums. Physicochemical parameters, such as dissolved oxygen, pH and Total hardness of aquaria were monitored daily. Results: The LC50 values for CuSO4 at 24, 48, 72, and 96 h of exposure, were 43.62, 12.6, 7.66, and 6.85 mg/L, respectively. The median LC50 value of CuSO4 for C.fusca was found to be 6.928 mg/L by EPA method and estimated to be 6.787 mg/L with SPSS statistical software. Conclusion: The mortality decreased with time, and most of the deaths occurred during the first 24 h. In addition, behavioural changes increased with increased concentration. This metal is an important constituent in industrial effluents discharged into freshwaters. The results obtained in this study clearly revealed the fact that it is necessary to control the use of a heavy metal such as copper.

[Leaching of nonferrous metals from copper-smelting slag with acidophilic microorganisms].

Science.gov (United States)

Murav'ev, M I; Fomchenko, N V

2013-01-01

The leaching process of copper and zinc from copper converter slag with sulphuric solutions of trivalent iron sulphate obtained using the association of acidophilic chemolithotrophic microorganisms was investigated. The best parameters of chemical leaching (temperature 70 degrees C, an initial concentration of trivalent iron in the leaching solution of 10.1 g/L, and a solid-phase content in the suspension of 10%) were selected. Carrying out the process under these parameters resulted in the recovery of 89.4% of copper and 39.3% of zinc in the solution. The possibility of the bioregeneration of trivalent iron in the solution obtained after the chemical leaching of slag by iron-oxidizingacidophilic chemolithotrophic microorganisms without inhibiting their activity was demonstrated.

Mineralogical Study of a Biologically-Based Treatment System That Removes Arsenic, Zinc and Copper from Landfill Leachate

Directory of Open Access Journals (Sweden)

Maryam Khoshnoodi

2013-12-01

Full Text Available Mineralogical characterization by X-ray diffraction (XRD and a high throughput automated quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN was conducted on samples from a sulphate-reducing biochemical reactor (BCR treating high concentrations of metals (As, Zn, Cu in smelter waste landfill seepage. The samples were also subjected to energy dispersive X-ray (EDX analysis of specific particles. The bulk analysis results revealed that the samples consisted mainly of silicate and carbonate minerals. More detailed phase analysis indicated four different classes: zinc-arsenic sulphosalts/sulphates, zinc-arsenic oxides, zinc phosphates and zinc-lead sulphosalts/sulphates. This suggests that sulphates and sulphides are the predominant types of Zn and As minerals formed in the BCR. Sphalerite (ZnS was a common mineral observed in many of the samples. In addition, X-ray point analysis showed evidence of As and Zn coating around feldspar and amphibole particles. The presence of arsenic-zinc-iron, with or without cadmium particles, indicated arsenopyrite minerals. Copper-iron-sulphide particles suggested chalcopyrite (CuFeS2 and tennantite (Cu,Fe12As4S13. Microbial communities found in each sample were correlated with metal content to describe taxonomic groups associated with high-metal samples. The research results highlight mineral grains that were present or formed at the site that might be the predominant forms of immobilized arsenic, zinc and copper.

Incorporation of layered double nanomaterials in thin film nanocomposite nanofiltration membrane for magnesium sulphate removal

Science.gov (United States)

Hanis Tajuddin, Muhammad; Yusof, Norhaniza; Salleh, Wan Norharyati Wan; Fauzi Ismail, Ahmad; Hanis Hayati Hairom, Nur; Misdan, Nurasyikin

2018-03-01

Thin film nanocomposite (TFN) membrane with copper-aluminium layered double hydroxides (LDH) incorporated into polyamide (PA) selective layer has been prepared for magnesium sulphate salt removal. 0, 0.05, 0.1, 0.15, 0.2 wt% of LDH were dispersed in the trimesoyl chloride (TMC) in n-hexane as organic solution and embedded into PA layer during interfacial polymerization with piperazine. The fabricated membranes were further characterized to evaluate its morphological structure and membrane surface hydrophilicity. The TFN membranes performance were evaluated with divalent salt magnesium sulphate (MgSO4) removal and compared with thin film composite (TFC). The morphological structures of TFN membranes were altered and the surface hydrophilicity were enhanced with addition of LDH. Incorporation of LDH has improved the permeate water flux by 82.5% compared to that of TFC membrane with satisfactory rejection of MgSO4. This study has experimentally validated the potential of LDH to improve the divalent salt separation performance for TFN membranes.

Incorporation of layered double nanomaterials in thin film nanocomposite nanofiltration membrane for magnesium sulphate removal

Directory of Open Access Journals (Sweden)

Tajuddin Muhammad Hanis

2018-01-01

Full Text Available Thin film nanocomposite (TFN membrane with copper-aluminium layered double hydroxides (LDH incorporated into polyamide (PA selective layer has been prepared for magnesium sulphate salt removal. 0, 0.05, 0.1, 0.15, 0.2 wt% of LDH were dispersed in the trimesoyl chloride (TMC in n-hexane as organic solution and embedded into PA layer during interfacial polymerization with piperazine. The fabricated membranes were further characterized to evaluate its morphological structure and membrane surface hydrophilicity. The TFN membranes performance were evaluated with divalent salt magnesium sulphate (MgSO4 removal and compared with thin film composite (TFC. The morphological structures of TFN membranes were altered and the surface hydrophilicity were enhanced with addition of LDH. Incorporation of LDH has improved the permeate water flux by 82.5% compared to that of TFC membrane with satisfactory rejection of MgSO4. This study has experimentally validated the potential of LDH to improve the divalent salt separation performance for TFN membranes.

Radioprotective effects of dextran sulphate in mice

International Nuclear Information System (INIS)

Vacek, A.; Bartonickova, A.; Rotkovska, D.; Palyga, G.F.; Zhukova, N.A.

1981-01-01

Influence of a single i.p. injection of dextran sulphate on radiosensitivity of mice was investigated. The administration of dextran sulphate 24, 48 and 72 hours prior to irradiation increased formation of endogenous colonies of the hemopoietic tissue on the surface of the spleen. DRF calculated from an equieffective exposure for 5 colonies was 1.96 when dextran sulphate was administered 24 hours before irradiation, and 2.25 when dextran sulphate was administered 72 hours before irradiation. The radioprotective effects of dextran sulphate were manifested also in the survival of animals exposed to lethal doses of short-termed as well as long-termed gamma radiation. (orig.) [de

Isotopic methods of investigations of hydrodynamics in installations for hydrometallurgic processing of copper concentrates

International Nuclear Information System (INIS)

Stsheletski, M.; Urban'ski, T.S.

1979-01-01

Isotope methods have been presented of investigations of hydrodynamics of liquid and solid phases in pilot-scale installations for hydrometallurgic processing of copper concentrates: in the column installation for leaching; in the tubular reactor for copper reduction by hydrogen and in the installation for crystallization of magnesium sulphate under pressure conditions. The column leaching installation has been tested by pulse injection of two radioisotope indicators simultaneously. The copper concentrate was labelled by sorbed colloidal gold-198 and the liquid phase was labelled by solution of sodium chloride containing sodium-24. Measurements of the radiation intensities were registered by scintillation counters, working with a single-channel amplitude analyzer, integrators and counting rate monitors. According to the distribution of time of stay, by the moments method, number of powers of ideal intermixings in the cell model of flow of the both phases. In the tubular reactor process of copper reduction by hydrogen is going on in three phases: gas-liquid-solig phase. Hydrodynamic investigations in this instalation was done in the presence of air, water and copper powder. Water was labelled by sodium-24 and copper powder by copper-64. Changes of intensity of radiation were measured by scintillation counters, located along the installation and were registered by multichannel amplitude analyzer. Peckle number and longitudal dispersion factor were determined. In investigations of the solid phase hydrodynamics during crystallization of magnesium sulphate under elevated temperature and high pressure, as an indicator, isotope gold-198 has been used, by which crystalls of the solid phase were labelled, and isotope sodium-24 was added to a liquid. Simultaneousely were measured and registered by a single-channel analyzer intensity of radiation of both indicators. Mean time of stay and parameters of a mathematical model of the phases flow in this installation were

Sulphate solubility and sulphate diffusion in oxide glasses: implications for the containment of sulphate-bearing nuclear wastes; Solubilite et cinetiques de diffusion des sulfates dans differents verres d'oxydes: application au conditionnement des dechets nucleaires sulfates

Energy Technology Data Exchange (ETDEWEB)

Lenoir, M.

2009-09-15

The thesis deals with sulphate solubility and sulphate diffusion in oxide glasses, in order to control sulphate incorporation and sulphate volatilization in nuclear waste glasses. It was conducted on simplified compositions, in the SiO{sub 2}-B{sub 2}O{sub 3}-R{sub 2}O (R = Li, Na, K, Cs), SiO{sub 2}-B{sub 2}O{sub 3}-BaO and V{sub 2}O{sub 5}-B{sub 2}O{sub 3}-BaO systems. These compositions allowed us to study the influence of the nature of network-modifying ions (Li{sup +}, Na{sup +}, K{sup +}, Cs{sup +} or Ba{sup 2+}) and also of former elements (Si, B, V), on structure and properties of glasses. Sulphate volatility is studied in sodium borosilicate melts using an innovative technique of sulphate quantitation with Raman spectroscopy. This technique is useful to obtain kinetic curves of sulphate volatilization. The establishment of a model to fit these curves leads to the determination of diffusion coefficients of sulphate. These diffusion coefficients can thus be compared to diffusion coefficients of other species, determined by other techniques and presented in the literature. They are also linked to diffusion coefficients in relation with the viscosity of the melts. Concerning sulphate solubility in glasses, it depends on glass composition and on the nature of sulphate incorporated. Sulphate incorporation in alkali borosilicate glasses leads to the formation of a sulphate layer floating on top of the melt. Sulphate incorporation in barium borosilicate and boro-vanadate glasses leads to the crystallization of sulphate species inside the vitreous matrix. Moreover, sulphate solubility is higher in these glasses than in alkali borosilicates. Finally, exchanges between cations present in glasses and cations present in the sulphate phase are also studied. (author)

Synthesis and characterization of copper nanofluid by a novel one-step method

International Nuclear Information System (INIS)

Kumar, S. Ananda; Meenakshi, K. Shree; Narashimhan, B.R.V.; Srikanth, S.; Arthanareeswaran, G.

2009-01-01

This paper presents a novel one-step method for the preparation of stable, non-agglomerated copper nanofluids by reducing copper sulphate pentahydrate with sodium hypophosphite as reducing agent in ethylene glycol as base fluid by means of conventional heating. This is an in situ, one-step method which gives high yield of product with less time consumption. The characterization of the nanofluid is done by particle size analyzer, X-ray diffraction topography, UV-vis analysis and Fourier transform infrared spectroscopy (FT-IR) followed by the study of thermal conductivity of nanofluid by the transient hot wire method

Removal of Sulphate and Manganese on Synthetic Wastewater in Sulphate Reducing Bioreactor Using Indonesian Natural Zeolite

Directory of Open Access Journals (Sweden)

Endah Retnaningrum

2017-07-01

Full Text Available The present research was conducted to investigate sulphate and manganese removal from synthetic wastewater. The continuous laboratory scale of down-flow fluidized-bed reactor (DFBR using sulphate reducing bacteria (SRB consortium and Indonesian natural zeolite as a bacterial support material was designed. At 9 days operation, maximum sulphate and manganese removal was observed to be 23% and 15.4%, respectively. The pH values were also changed to neutral. The population of SRB increased which effect on the raising of their activity for removing sulphate and manganese. Using the scanning electronic microscopy (SEM, it was observed that natural zeolite possesses excellent physical characteristics as a bacterial support material in DFBR. The imaging SEM result of SRB consortium on zeolite surface clearly showed the developed SRB biofilm on that particle. Analysis result of EDX confirmed that manganese was precipitated as manganese–sulfides.

Integrating biomass, sulphate and sea-salt aerosol responses into a microphysical chemical parcel model: implications for climate studies.

Science.gov (United States)

Ghosh, S; Smith, M H; Rap, A

2007-11-15

Aerosols are known to influence significantly the radiative budget of the Earth. Although the direct effect (whereby aerosols scatter and absorb solar and thermal infrared radiation) has a large perturbing influence on the radiation budget, the indirect effect (whereby aerosols modify the microphysical and hence the radiative properties and amounts of clouds) poses a greater challenge to climate modellers. This is because aerosols undergo chemical and physical changes while in the atmosphere, notably within clouds, and are removed largely by precipitation. The way in which aerosols are processed by clouds depends on the type, abundance and the mixing state of the aerosols concerned. A parametrization with sulphate and sea-salt aerosol has been successfully integrated within the Hadley Centre general circulation model (GCM). The results of this combined parametrization indicate a significantly reduced role, compared with previous estimates, for sulphate aerosol in cloud droplet nucleation and, consequently, in indirect radiative forcing. However, in this bicomponent system, the cloud droplet number concentration, N(d) (a crucial parameter that is used in GCMs for radiative transfer calculations), is a smoothly varying function of the sulphate aerosol loading. Apart from sea-salt and sulphate aerosol particles, biomass aerosol particles are also present widely in the troposphere. We find that biomass smoke can significantly perturb the activation and growth of both sulphate and sea-salt particles. For a fixed salt loading, N(d) increases linearly with modest increases in sulphate and smoke masses, but significant nonlinearities are observed at higher non-sea-salt mass loadings. This non-intuitive N(d) variation poses a fresh challenge to climate modellers.

Demonstration of immunogenic keratan sulphate in commercial chondroitin 6-sulphate from shark cartilage. Implications for ELISA assays

DEFF Research Database (Denmark)

Møller, H J; Møller-Pedersen, T; Damsgaard, T E

1995-01-01

The prototype monoclonal keratan sulphate (KS) antibody 5D4 that is widely used for detection of KS in tissues and biological fluids reacts strongly with commercial low grade shark cartilage chondroitin 6-sulphate. Characterization of the immunogenic material by chondroitinase ABC digestion, ELISA...... cartilage chondroitin 6-sulphate is an easy accessible source of immunogenic KS that can be used as a reference standard and as coating antigen in KS-ELISAs. The concentration of immunogenic KS in synovial fluid measured with an ELISA based solely on reagents of shark cartilage chondroitin 6-sulphate...... correlated well (r = 0.90) with the concentrations obtained with a traditional KS-ELISA that uses purified aggrecan as standard and coating antigen, and KS in both serum and synovial fluid could be measured with sufficient linearity....

Effectivness of dexametasone vs. Magnesium sulphate in postoperative analgesia: Dexametasone vs. Magnesium sulphate

Directory of Open Access Journals (Sweden)

Dautaj Brikena

2016-01-01

Full Text Available Introduction: Preoperative use of additive substances may be very helpful in perioperative acute pain management. Intravenous administration of dexametasone in preoperative period prevents postoperative nausea and vomiting but also provides better pain relief. It is also well known that magnesium sulphate (the NMDA receptor's antagonist by its central mechanism of action may be effective in postoperative pain control. Aim: The purpose of this study was to evaluate the effect of dexametasone and magnesium sulphate on postoperative pain management in patients undergoing abdominal surgery (open cholecystectomy. Methods: Seventy eight patients scheduled for elective surgery (open cholecystectomy were included in this study. This was the prospective cohort randomized placebo- controlled study. A total of 78 patients were randomized into three groups. Each group had twenty six patients. The group D, received dexametasone 0.1 mg/ kg iv 30 minutes before surgery. The group M received magnesium sulphate 3 mg/kg iv 30 minutes before surgery. The third group S was placebo group and patients in this group received saline in the same volume for each patient. For pain control after surgery all patients received tramadol 0.9-1.2 mg/kg and diklophenac 1.76 mg/kg. When necessary (VAS ≥ 7, morphine sulphate in dose 0.15 mg/kg was administred subcutaneously For treatment of emetic episodes metoclopramid 10 mg iv. was used. The patients were observed for intensity of pain measured VAS 0-10, pain relief and satisfaction with therapy, sedation, adverse events, emetic episodes and hemodynamic parameters. Results: There was no difference between groups regarding demographic data (age, gender, body weight, ASA score, comorbidity, duration of surgery and anesthesia and amount of fentanyl received during surgery. In group D 11.54% of patients received additional analgesia (morphine sulphate 0.15 mg/kg sc in the first 4 hours and 27% of patients in the first 24 hours

Influence of copper and formalin on the mycorrhiza of pine (Pinus kesiya Royle ex Gordon

Directory of Open Access Journals (Sweden)

G. D. Sharma

2014-08-01

Full Text Available Various concentrations of copper sulphate and formalin were tested for their effect on the efficiency of mycorrhizal functioning in pine seedlings. Low and higher doses of copper applied to the container grown seedling exhibited a less stimulatory effect than nedium doses. When applied in higher concentrations, the formalin caused mortality in young pine seedlings. The seedling yield and phosphate uptake was found maximum in 100 ppm applied concentration of copper. while słów growth and lower phosphate concentration was observed in the seedlings not given any copper treatment. Formalin at 50 ppm concentration slightly improved the seedling growth and phosphate uptake in mycorrhizal seedling as compared with untreated ones. Variation in the development and spread of ectomycorrhiza on the surface of roots of pine seedlings was also recorded in responses to copper and formalin treatments.

High emittance black nickel coating on copper substrate for space applications

Energy Technology Data Exchange (ETDEWEB)

Somasundaram, Soniya, E-mail: jrf0013@isac.gov.in; Pillai, Anju M., E-mail: anjum@isac.gov.in; Rajendra, A., E-mail: rajendra@isac.gov.in; Sharma, A.K., E-mail: aks@isac.gov.in

2015-09-15

Highlights: • High emittance black nickel coating is obtained on copper substrate. • The effect of various process parameters on IR emittance is studied systematically. • Process parameters are optimized to develop a high emittance black nickel coating. • Coating obtained using the finalized parameters exhibited an emittance of 0.83. • SEM and EDAX are used for coating characterization. - Abstract: Black nickel, an alloy coating of zinc and nickel, is obtained on copper substrate by pulse electrodeposition from a modified Fishlock bath containing nickel sulphate, nickel ammonium sulphate, zinc sulphate and ammonium thiocyanate. A nickel undercoat of 4–5 μm thickness is obtained using Watts bath to increase the corrosion resistance and adhesion of the black nickel coating. The effect of bath composition, temperature, solution pH, current density and plating time on the coating appearance and corresponding infra-red emittance of the coating is investigated systematically. Process parameters are optimized to develop a high emittance space worthy black nickel coating to improve the heat radiation characteristics. The effect of the chemistry of the plating bath on the coating composition was studied using energy dispersive X-ray analysis (EDAX) of the coatings. The 5–6 μm thick uniform jet black zinc–nickel alloy coating obtained with optimized process exhibited an emittance of 0.83 and an absorbance of 0.92. The zinc to nickel ratio of black nickel coatings showing high emittance and appealing appearance was found to be in the range 2.3–2.4.

Copper vertical micro dendrite fin arrays and their superior boiling heat transfer capability

Science.gov (United States)

Wang, Ya-Qiao; Lyu, Shu-Shen; Luo, Jia-Li; Luo, Zhi-Yong; Fu, Yuan-Xiang; Heng, Yi; Zhang, Jian-Hui; Mo, Dong-Chuan

2017-11-01

Micro pin fin arrays have been widely used in electronic cooling, micro reactors, catalyst support, and wettability modification and so on, and a facile way to produce better micro pin fin arrays is demanded. Herein, a simple electrochemical method has been developed to fabricate copper vertical micro dendrite fin arrays (Cu-VMDFA) with controllable shapes, number density and height. High copper sulphate concentration is one key point to make the dendrite stand vertically. Besides, the applied current should rise at an appropriate rate to ensure the copper dendrite can grow vertically on its own. The Cu-VMDFA can significantly enhance the heat transfer coefficient by approximately twice compared to the plain copper surface. The Cu-VMDFA may be widely used in boiling heat transfer areas such as nuclear power plants, electronic cooling, heat exchangers, and so on.

Electrodeposited porous and amorphous copper oxide film for application in supercapacitor

Energy Technology Data Exchange (ETDEWEB)

Patake, V.D. [Thin Film Physics Laboratory, Department of Physics, Shivaji University, Kolhapur 416004, (M.S.) (India); Joshi, S.S. [Clean Energy Research Center, Korea Institute of Science and Technology, Cheongryang, Seoul 130-650 (Korea, Republic of); Lokhande, C.D. [Thin Film Physics Laboratory, Department of Physics, Shivaji University, Kolhapur 416004, (M.S.) (India); Clean Energy Research Center, Korea Institute of Science and Technology, Cheongryang, Seoul 130-650 (Korea, Republic of)], E-mail: l_chandrakant@yahoo.com; Joo, Oh-Shim [Clean Energy Research Center, Korea Institute of Science and Technology, Cheongryang, Seoul 130-650 (Korea, Republic of)], E-mail: joocat@kist.rre.kr

2009-03-15

In present study, the porous amorphous copper oxide thin films have been deposited from alkaline sulphate bath. The cathodic electrodeposition method was employed to deposit copper oxide film at room temperature on stainless steel substrate. Their structural and surface morphological properties were investigated by means of X-ray diffraction (XRD) and scanning electron micrograph (SEM), respectively. To propose this as a new material for possible application in the supercapacitor, its electrochemical properties have been studied in aqueous 1 M Na{sub 2}SO{sub 4} electrolyte using cyclic voltammetry. The structural analysis from XRD pattern showed the formation of amorphous copper oxide film on the substrate. The surface morphological studies from scanning electron micrographs revealed the formation of porous cauliflower-like copper oxide film. The cyclic voltammetric curves showed symmetric nature and increase in capacitance with increase in film thickness. The maximum specific capacitance of 36 F g{sup -1} was exhibited for the 0.6959 mg cm{sup -2} film thickness. This shows that low-cost copper oxide electrode will be a potential application in supercapacitor.

Demonstration of immunogenic keratan sulphate in commercial chondroitin 6-sulphate from shark cartilage. Implications for ELISA assays

DEFF Research Database (Denmark)

Møller, H J; Møller-Pedersen, T; Damsgaard, T E

1995-01-01

The prototype monoclonal keratan sulphate (KS) antibody 5D4 that is widely used for detection of KS in tissues and biological fluids reacts strongly with commercial low grade shark cartilage chondroitin 6-sulphate. Characterization of the immunogenic material by chondroitinase ABC digestion, ELISA...... inhibition studies, immunoblotting and HPLC analyses confirmed the presence of substantial amounts of KS, probably as a large proteoglycan (> 120 kDa). Commercial and heterogenic glycosaminoglycan preparations therefore must be used with great caution in immunological analyses. On the other hand the shark...... cartilage chondroitin 6-sulphate is an easy accessible source of immunogenic KS that can be used as a reference standard and as coating antigen in KS-ELISAs. The concentration of immunogenic KS in synovial fluid measured with an ELISA based solely on reagents of shark cartilage chondroitin 6-sulphate...

Extraction of sulphates by long chain amines

International Nuclear Information System (INIS)

Boirie, Ch.

1959-05-01

The extraction of sulphuric acid by long chain amines in organic solution has been studied with a view to determining the value of the stability constants of the amine sulphates and bi-sulphates formed. We have concentrated chiefly on uranium sulphate and thorium sulphate. The formulae of the complexes extractable with amines have been established, as well as the corresponding dissociation constants. We have observed that for uranium sulphate the formula of the complex depends only on the nature of the amine, whereas for thorium this formula varies with the amine structure. From the formulae determined and the value of the constants calculated, we have been able to establish the best conditions for uranium and thorium extraction and also for a separation of these two elements. Finally we propose an application of this study to the determination of uranium in ores, where the separation of uranium by this method is particularly easy and complete. (author) [fr

Sulphate deposition by precipitation into Lake Ontario

Energy Technology Data Exchange (ETDEWEB)

Shaw, R W; Whelpdale, D M

1973-01-01

Measurements of sulphate concentration in precipitation from individual snow storms of several hours duration in the western Lake Ontario region indicate that approximately 9-66 mg/M/sub 2/ of SO/sub 4//sup 2 -/ is being deposited into the lake per storm. This amount is up to several times more than daily average values over long periods found by other workers. Using a mean sulphate concentration of 4 mg/l and an annual accumulation of precipitation of 760 mm, the yearly sulphate deposition by precipitation is about 0.1% of the total mass of sulphate in the lake; however, more significantly, it is of the same order of magnitude as that discharged directly into the lake by industry.

Mortar and concrete based on calcium sulphate binders

NARCIS (Netherlands)

Bakker, J.J.F.; Brouwers, H.J.H.; Fischer, H.B

2006-01-01

In this study both hemi-hydrate and anhydrite are tested as calcium sulphate binders for structural mortar and concrete. The advantage of using calcium sulphates instead of cement as a binder is the fact that the production of calcium sulphate is more environmental friendly than that of cement. For

Copper recovery from slag by indirect bio leaching

International Nuclear Information System (INIS)

Mazuelos, A.; Iglesias, N.; Romero, R.; Forcat, O.; Carranza, F.

2009-01-01

The main source of copper loss from a smelter is copper in discard slag. Slag can contain Cu in concentrations very much higher than those of many ores. Cu is present in slag entrained in very small drops of matte, white metal and blister copper occluded in fayalitic phase. In this work, the technical viability of the BRISA process, that is based on the indirect bio leaching, for this residue has been proved. A sample of slag, containing 2 % of copper, has been chemical, granulometric and metallographic characterized and it has been leached with ferric sulphate solutions in agitated reactors. The influence of several variables have been investigated. Once the best operating conditions had been selecting and an economic estimation had been done (with very really attractive results), the leaching stage has been designed for a plant of 30 tonnes per hour capacity. Cu extractions higher than 70% can be achieved with a residence time of only five hours. Despite of Cu(II) concentration in fed is as high as 30 g/l, bio oxidation stage can supply Fe(III) demanded by ferric leaching stage. (Author) 17 refs

Physicochemical and in vitro deposition properties of salbutamol sulphate/ipratropium bromide and salbutamol sulphate/excipient spray dried mixtures for use in dry powder inhalers.

Science.gov (United States)

Corrigan, Deirdre O; Corrigan, Owen I; Healy, Anne Marie

2006-09-28

The physicochemical and aerodynamic properties of spray dried powders of the drug/drug mixture salbutamol sulphate/ipratropium bromide were investigated. The in vitro deposition properties of spray dried salbutamol sulphate and the spray dried drug/excipient mixtures salbutamol sulphate/lactose and salbutamol sulphate/PEG were also determined. Spray drying ipratropium bromide monohydrate resulted in a crystalline material from both aqueous and ethanolic solution. The product spray dried from aqueous solution consisted mainly of ipratropium bromide anhydrous. There was evidence of the presence of another polymorphic form of ipratropium bromide. When spray dried from ethanolic solution the physicochemical characterisation suggested the presence of an ipratropium bromide solvate with some anhydrous ipratropium bromide. Co-spray drying salbutamol sulphate with ipratropium bromide resulted in amorphous composites, regardless of solvent used. Particles were spherical and of a size suitable for inhalation. Twin impinger studies showed an increase in the fine particle fraction (FPF) of spray dried salbutamol sulphate compared to micronised salbutamol sulphate. Co-spray dried salbutamol sulphate:ipratropium bromide 10:1 and 5:1 systems also showed an increase in FPF compared to micronised salbutamol sulphate. Most co-spray dried salbutamol sulphate/excipient systems investigated demonstrated FPFs greater than that of micronised drug alone. The exceptions to this were systems containing PEG 4000 20% or PEG 20,000 40% both of which had FPFs not significantly different from micronised salbutamol sulphate. These two systems were crystalline unlike most of the other spray dried composites examined which were amorphous in nature.

Sulphate reduction and vertical distribution of sulphate-reducing bacteria quantified by rRNA slot-blot hybridization in a coastal marine sediment

DEFF Research Database (Denmark)

Sahm, K.; MacGregor, BJ; Jørgensen, BB

1999-01-01

In the past, enumeration of sulphate-reducing bacteria (SRB) by cultivation-based methods generally contradicted measurements of sulphate reduction, suggesting unrealistically high respiration rates per cell. Here, we report evidence that quantification of SRB rRNA by slot-blot hybridization......, directly above the sulphate reduction maximum. Cell numbers calculated by converting the relative contribution of SRB rRNA to the percentage of DAPI-stained cells indicated a population size for SRB of 2.4-6.1 x 10(8) cells cm(-3) wet sediment. Cellular sulphate reduction rates calculated on the basis...

Electrochemical study in the molten sodium acid sulphate - potassium acid sulphate eutectic

International Nuclear Information System (INIS)

Le Ber, F.

1964-01-01

The general properties of the NaHSO 4 - KHSO 4 molten eutectic resemble those of neutral sulphates and those of concentrated H 2 SO 4 . We have been able to show the existence in solution of the ions HSO - 4 SO 2- 4 , and H 3 O + , these last being formed by the action of the HSO - 4 ions on dissolved H 2 O. The electro-active zone with a polished platinum electrode is limited in oxidation by the ions H 3 O + and SO 2- 4 , and in reduction by the protons of HSO - 4 . We have compared the electro-active zones obtained with different electrodes (Ag-Au-graphite-mercury). We have considered the dissolution of a few metallic oxides and halides. This work shows the role as O 2- ion acceptors of HSO - 4 ions. We have undertaken an electro-chemical study of a few oxido-reduction Systems: H + / H 2 , Ag↓ / Ag (1), the vanadium and uranium Systems, those of mercury Hg↓ / Hg 2- 2 and of gold Au/Au 3+ , then of the attack by the solvent of a few common metals such as aluminium, iron, copper and nickel. The study of silver Systems has made it possible to obtain the solubility products of AgCl and AgBr and to consider the possibility of coulometric titration Cl - ions with Ag + ions. We have shown the existence of various chemical species of vanadium which may exist in the molten eutectic. (author) [fr

Reaction and nucleation mechanisms of copper electrodeposition on disposable pencil graphite electrode

Energy Technology Data Exchange (ETDEWEB)

Majidi, M.R. [Department of Analytical Chemistry, Faculty of Chemistry, University of Tabriz, 29th Bahman Bolvard, Tabriz 51664 (Iran, Islamic Republic of)], E-mail: sr.majidi@gmail.com; Asadpour-Zeynali, K.; Hafezi, B. [Department of Analytical Chemistry, Faculty of Chemistry, University of Tabriz, 29th Bahman Bolvard, Tabriz 51664 (Iran, Islamic Republic of)

2009-01-01

The reaction and nucleation mechanism of copper electrodeposition on disposable pencil graphite electrode (PGE) in acidic sulphate solution were investigated using cyclic voltammetry (CV) and chronoamperometry (CA) techniques, respectively. Electrochemical experiments were followed by morphological studies with scanning electron microscopy (SEM). The effect of some experimental parameters, namely copper concentration, pH, scan rate, background electrolyte, deposition potential, and conditioning surface of the electrode were described. At the surface of PGE, Cu{sup 2+} ions were reduced at -250 mV vs. SCE. It was found that electrodeposition of copper is affected by rough surface of PGE. The nucleation mechanisms were examined by fitting the experimental CA data into Scharifker-Hills nucleation models. The nuclei population densities were also determined by means of two common fitting models developed for three-dimensional nucleation and growth (Scharifker-Mostany and Mirkin-Nilov-Herrman-Tarallo). It was found that deposition potential and background electrolyte affect the distribution of the deposited copper. The morphology of the deposited copper is affected by background electrolyte.

Gut Health of Pigs: Challenge Models and Response Criteria with a Critical Analysis of the Effectiveness of Selected Feed Additives - A Review.

Science.gov (United States)

Adewole, D I; Kim, I H; Nyachoti, C M

2016-07-01

The gut is the largest organ that helps with the immune function. Gut health, especially in young pigs has a significant benefit to health and performance. In an attempt to maintain and enhance intestinal health in pigs and improve productivity in the absence of in-feed antibiotics, researchers have evaluated a wide range of feed additives. Some of these additives such as zinc oxide, copper sulphate, egg yolk antibodies, mannan-oligosaccharides and spray dried porcine plasma and their effectiveness are discussed in this review. One approach to evaluate the effectiveness of these additives in vivo is to use an appropriate disease challenge model. Over the years, researchers have used a number of challenge models which include the use of specific strains of enterotoxigenic Escherichia coli, bacteria lipopolysaccharide challenge, oral challenge with Salmonella enteric serotype Typhimurium, sanitation challenge, and Lawsonia intercellularis challenge. These challenge models together with the criteria used to evaluate the responses of the animals to them are also discussed in this review.

Pitting corrosion of copper. An equilibrium - mass transport study

International Nuclear Information System (INIS)

Taxen, C.

2002-08-01

A mathematical model for the propagation of corrosion pits is described and used to calculate the potentials below which copper is immune to pitting. The model uses equilibrium data and diffusion coefficients and calculates the stationary concentration profiles of 26 aqueous species from the bulk water outside a corrosion pit to the site of the metal dissolution. Precipitation of oxides and salts of copper is considered. Studied conditions include water compositions from tap waters to seawater at the temperatures 25 deg C and 75 deg C. Carbonate and sulphate are aggressive towards copper because of complex formation with divalent copper. Carbonate is less aggressive in a corrosion pit than outside at the pH of the bulk. Carbonate carries acidity out from the pit, favours oxide formation and may prevent the initiation of acidic corrosion pits. The concentration profiles are used to estimate the maximum propagation rates for a corrosion pit. A high potential is found to be the most important factor for the rate of propagation. The levels of potential copper can sustain, as corrosion potentials are discussed in terms of the stability of cuprous oxide as a cathode material for oxygen reduction relative to non-conducting cupric phases

Pitting corrosion of copper. An equilibrium - mass transport study

Energy Technology Data Exchange (ETDEWEB)

Taxen, C. [Swedish Corrosion Inst., Stockholm (Sweden)

2002-08-01

A mathematical model for the propagation of corrosion pits is described and used to calculate the potentials below which copper is immune to pitting. The model uses equilibrium data and diffusion coefficients and calculates the stationary concentration profiles of 26 aqueous species from the bulk water outside a corrosion pit to the site of the metal dissolution. Precipitation of oxides and salts of copper is considered. Studied conditions include water compositions from tap waters to seawater at the temperatures 25 deg C and 75 deg C. Carbonate and sulphate are aggressive towards copper because of complex formation with divalent copper. Carbonate is less aggressive in a corrosion pit than outside at the pH of the bulk. Carbonate carries acidity out from the pit, favours oxide formation and may prevent the initiation of acidic corrosion pits. The concentration profiles are used to estimate the maximum propagation rates for a corrosion pit. A high potential is found to be the most important factor for the rate of propagation. The levels of potential copper can sustain, as corrosion potentials are discussed in terms of the stability of cuprous oxide as a cathode material for oxygen reduction relative to non-conducting cupric phases.

Effects of Topical Corticosteroid and Tacrolimus on Ceramides and Irritancy to Sodium Lauryl Sulphate in Healthy Skin

DEFF Research Database (Denmark)

Jungersted, Jakob Mutanu; Høgh, Julie Kaae; Hellgren, Lars

2011-01-01

twice daily for one week with betamethasone, tacrolimus, emollient, or left untreated, respectively. After one week each area was challenged with a 24 h sodium lauryl sulphate patch test. The lipids were collected using the cyanoacrylate method and evaluated by high performance thin layer chromatography...... found between treatment regimes. Pretreatment with betamethasone (p = 0.01) or with tacrolimus (p = 0.001) causes a decreased inflammatory response to sodium lauryl sulphate compared with emollient. In conclusion, treatment with betamethasone and tacrolimus has a positive effect on the ceramide...

Biomass reduction of Salvinia molesta exposed to copper sulfate pentahydrate (CuSO4.5H2O)

OpenAIRE

Barros,João Pedro Alves de Azevedo; Henares,Matheus Nicolino Peixoto

2015-01-01

Copper in the aquatic ecosystem may remain adsorbed or be incorporated into the biomass and undergo biomagnification causing unwanted effects to aquatic macrophyte communities. This study evaluated the biomass reduction of Salvinia molesta (Mitchell) exposed to copper sulphate pentahydrate (CuSO4.5H2O) under laboratory conditions. Approximately 20.5 g of fresh mass (FM) of S. molesta (0.74 g dry matter, DM) were placed in glass tanks with different concentrations (n = 3) of CuSO4.5H2O as foll...

Sulphate reduction and vertical distribution of sulphate-reducing bacteria quantified by rRNA slot-blot hybridization in a coastal marine sediment

DEFF Research Database (Denmark)

Sahm, K.; MacGregor, BJ; Jørgensen, BB

1999-01-01

In the past, enumeration of sulphate-reducing bacteria (SRB) by cultivation-based methods generally contradicted measurements of sulphate reduction, suggesting unrealistically high respiration rates per cell. Here, we report evidence that quantification of SRB rRNA by slot-blot hybridization...... between 18% and 25% to the prokaryotic rRNA pool. The dominant SRB were related to complete oxidizing genera (Desulphococcus, Desulphosarcina and Desulphobacterium), while Desulpho-bacter could not be detected. The vertical profile and quantity of rRNA from SRB was compared with sulphate reduction rates......, directly above the sulphate reduction maximum. Cell numbers calculated by converting the relative contribution of SRB rRNA to the percentage of DAPI-stained cells indicated a population size for SRB of 2.4-6.1 x 10(8) cells cm(-3) wet sediment. Cellular sulphate reduction rates calculated on the basis...

Sulphate rocks as an arena for karst development

Directory of Open Access Journals (Sweden)

Andrejchuk V.

1996-01-01

Full Text Available The rocks in which karst systems develop are most commonly composed of carbonate sulphate and chloride minerals. The sulphate minerals are quite numerous, but only gypsum and anhydrite form extensive masses in sedimentary sequences. Other minerals, which represent sulphates of K, Mg and Na, normally occur as minor beds (0.1-5.0 m, or as inclusions associated with chloride rocks. However some minerals precipitated in salt-generating basins, such as mirabilite and glauberite (typically formed in the Kara-Bogaz-Gol Gulf, salt lakes of Siberia and in China, form sequences up to 5-10 m thick where karst may develop. Due to the very high solubility of Na -sulphates, karst processes and features occurring in these rocks resemble salt karst. Thus, the term sulphate karst, although not strictly correct, is used mainly to indicate karst developed in gypsum and anhydrite.

Occurrence of sulphate reducing bacteria (SRB) associated with biocorrosion on metallic surfaces in a hydroelectric power station in Ibirama (SC) - Brazil

OpenAIRE

Paulo Roberto Dantas Marangoni; Diogo Robl; Marcos Antonio Coelho Berton; Carlos Mario Garcia; Angela Bozza; Mariana Vieira Porsani; Patricia do Rocio Dalzoto; Vânia Aparecida Vicente; Ida Chapaval Pimentel

2013-01-01

The aim of this study was evaluate, two methods for the detection and identification of sulphate reducing bacteria (SRB): ML medium and PCR with specific primers for SRB groups. SRB were detected through the selective medium only on carbon steel, which showed corrosion. Employing specific PCR primer, SBR were detected from all the metallic components assayed, even those that did not present visible corrosion spots, such stainless steel and copper alloys. Despite the presence or absence of cor...

Gut Health of Pigs: Challenge Models and Response Criteria with a Critical Analysis of the Effectiveness of Selected Feed Additives — A Review

Science.gov (United States)

Adewole, D. I.; Kim, I. H.; Nyachoti, C. M.

2016-01-01

The gut is the largest organ that helps with the immune function. Gut health, especially in young pigs has a significant benefit to health and performance. In an attempt to maintain and enhance intestinal health in pigs and improve productivity in the absence of in-feed antibiotics, researchers have evaluated a wide range of feed additives. Some of these additives such as zinc oxide, copper sulphate, egg yolk antibodies, mannan-oligosaccharides and spray dried porcine plasma and their effectiveness are discussed in this review. One approach to evaluate the effectiveness of these additives in vivo is to use an appropriate disease challenge model. Over the years, researchers have used a number of challenge models which include the use of specific strains of enterotoxigenic Escherichia coli, bacteria lipopolysaccharide challenge, oral challenge with Salmonella enteric serotype Typhimurium, sanitation challenge, and Lawsonia intercellularis challenge. These challenge models together with the criteria used to evaluate the responses of the animals to them are also discussed in this review. PMID:26954144

Sulphate reduction experiment: SURE-1

International Nuclear Information System (INIS)

Pedersen, K.; Arlinger, J.; Bengtsson, A.; Edlund, J.; Eriksson, L.; Hallbeck, L.; Johansson, J.; Paeaejaervi, A.; Rabe, L.

2013-11-01

It was previously concluded that opposing gradients of sulphate and methane, observations of 16S rDNA sequences displaying great similarity to those of anaerobic methane-oxidizing Archaea, and a peak in sulphide concentration in groundwater from a depth of 250-350 m in Olkiluoto, Finland, indicated proper conditions for methane oxidation with sulphate. In the present research (SURE-1), pressure-resistant, gas-tight circulating systems were constructed to enable the investigation of attached and unattached anaerobic microbial populations from a depth of 327 m in Olkiluoto under in situ pressure (2.4 MPa), diversity, dissolved gas, and hydrochemical conditions of groundwater station ONKPVA6. Three parallel flow cell cabinets were configured to allow observation of the influence on microbial metabolic activity of 11 mM methane, 11 mM methane plus 10 mM H 2 , or 2.1 mM O 2 plus 7.9 mM N 2 (i.e., air). The concentrations of these gases and of organic acids and carbon, sulphur chemistry, pH and E h , ATP, numbers of cultivable microorganisms, and total numbers of cells and bacteriophages were subsequently recorded under batch conditions for 105 d. The system containing H 2 and methane displayed microbial reduction of 0.7 mM sulphate to sulphide, while the system containing only methane produced 0.2 mM reduced sulphate. The system containing added air became inhibited and displayed no signs of microbial activity. Added H 2 and methane induced increasing numbers of lysogenic bacteriophages per cell. It appears possible that a microbial anaerobic methane-oxidizing process coupled to acetate formation and sulphate reduction may be ongoing in aquifers at a depth of 250-350 m in Olkiluoto, but clear evidence of such an AOM process was not obtained. (orig.)

Sulphate reduction experiment: SURE-1

Energy Technology Data Exchange (ETDEWEB)

Pedersen, K.; Arlinger, J.; Bengtsson, A.; Edlund, J.; Eriksson, L.; Hallbeck, L.; Johansson, J.; Paeaejaervi, A.; Rabe, L. [Microbial Analytics Sweden AB, Moelnlycke (Sweden)

2013-11-15

It was previously concluded that opposing gradients of sulphate and methane, observations of 16S rDNA sequences displaying great similarity to those of anaerobic methane-oxidizing Archaea, and a peak in sulphide concentration in groundwater from a depth of 250-350 m in Olkiluoto, Finland, indicated proper conditions for methane oxidation with sulphate. In the present research (SURE-1), pressure-resistant, gas-tight circulating systems were constructed to enable the investigation of attached and unattached anaerobic microbial populations from a depth of 327 m in Olkiluoto under in situ pressure (2.4 MPa), diversity, dissolved gas, and hydrochemical conditions of groundwater station ONKPVA6. Three parallel flow cell cabinets were configured to allow observation of the influence on microbial metabolic activity of 11 mM methane, 11 mM methane plus 10 mM H{sub 2}, or 2.1 mM O{sub 2} plus 7.9 mM N{sub 2} (i.e., air). The concentrations of these gases and of organic acids and carbon, sulphur chemistry, pH and E{sub h}, ATP, numbers of cultivable microorganisms, and total numbers of cells and bacteriophages were subsequently recorded under batch conditions for 105 d. The system containing H{sub 2} and methane displayed microbial reduction of 0.7 mM sulphate to sulphide, while the system containing only methane produced 0.2 mM reduced sulphate. The system containing added air became inhibited and displayed no signs of microbial activity. Added H{sub 2} and methane induced increasing numbers of lysogenic bacteriophages per cell. It appears possible that a microbial anaerobic methane-oxidizing process coupled to acetate formation and sulphate reduction may be ongoing in aquifers at a depth of 250-350 m in Olkiluoto, but clear evidence of such an AOM process was not obtained. (orig.)

Sulphate Removal from Water by Carbon Residue from Biomass Gasification: Effect of Chemical Modification Methods on Sulphate Removal Efficiency

Directory of Open Access Journals (Sweden)

Hanna Runtti

2016-02-01

Full Text Available Sulphate removal from mine water is a problem because traditional chemical precipitation does not remove all sulphates. In addition, it creates lime sediment as a secondary waste. Therefore, an inexpensive and environmental-friendly sulphate removal method is needed in addition to precipitation. In this study, carbon residues from a wood gasification process were repurposed as precursors to a suitable sorbent for SO42- ion removal. The raw material was modified using ZnCl2, BaCl2, CaCl2, FeCl3, or FeCl2. Carbon residues modified with FeCl3 were selected for further consideration because the removal efficiency toward sulphate was the highest. Batch sorption experiments were performed to evaluate the effects of the initial pH, initial SO42- ion concentration, and contact time on sulphate removal. The removal of SO42- ions using Fe-modified carbon residue was notably higher compared with unmodified carbon residue and commercially available activated carbon. The sorption data exhibited pseudo-second-order kinetics. The isotherm analysis indicated that the sorption data of Fe-modified carbon residues can be represented by the bi-Langmuir isotherm model.

Chemical sulphate removal for treatment of construction and demolition debris leachate.

Science.gov (United States)

Kijjanapanich, Pimluck; Annachhatre, Ajit P; Esposito, Giovanni; Lens, Piet N L

2014-08-01

Construction and demolition debris (CDD) is a product of construction, renovation or demolition activities. It has a high gypsum content (52.4% of total gypsum), concentrated in the CDD sand (CDDS) fraction. To comply with the posed limit of the maximum amount of sulphate present in building sand, excess sulphate needs to be removed. In order to enable reuse of CDDS, a novel treatment process is developed based on washing of the CDDS to remove most of the gypsum, and subsequent sulphate removal from the sulphate-rich CDDS leachate. This study aims to assess chemical techniques, i.e. precipitation and adsorption, for sulphate removal from the CDDS leachate. Good sulphate removal efficiencies (up to 99.9%) from the CDDS leachate can be achieved by precipitation with barium chloride (BaCl2) and lead(II) nitrate (Pb(NO3)2). Precipitation with calcium chloride (CaCl2), calcium carbonate (CaCO3) and calcium oxide (CaO) gave less efficient sulphate removal. Adsorption of sulphate to aluminium oxide (Al2O3) yielded a 50% sulphate removal efficiency, whereas iron oxide-coated sand as adsorbent gave only poor (10%) sulphate removal efficiencies.

Uranium and sulphate values from carbonate leach process

International Nuclear Information System (INIS)

Berger, B.

1983-01-01

The process concerns the recovery of uraniferous and sulphur values from liquor resulting from the attack of sulphur containing uraniferous ores by an alkaline solution of sodium carbonate and/or bicarbonate. Ammonia is introduced into the liquor to convert any HCO 3 - to CO 3 2- . The neutralised liquor from this step is then contacted with an anion exchange resin to fix the uranium and sulphate ions, leaving a liquor containing ammonia, sodium carbonate and/or bicarbonate in solution. Uranium and sulphate ions are eluted with an ammonia carbonate and/or bicarbonate solution to yield a solution of ammonium uranyl carbonate complex and ammonium sulphate. The solution is subjected to thermal treatment until a suspension of precipitated ammonium uranate and/or diuranate is obtained in a solution of the ammonium sulphate. Carbon dioxide, ammonia and water vapor are driven off. The precipitated ammonium uranate and/or diuranate is then separated from the solution of ammonium sulphate and the precipitate is calcined to yield uranium trioxide and ammonia

Sulphate Incorporation in Borosilicate Glasses and Melts: a Kinetic Approach

Energy Technology Data Exchange (ETDEWEB)

Lenoir, M. [CEA, DEN, Laboratoire d' etude et de Developpement de Matrices de Conditionnement, Centre de Marcoule, 30207 Bagnols-sur-Ceze (France); Physique des Mineraux et Magmas, UMR 7047, CNRS- Institut de Physique du Globe de Paris, 7 place Jussieu, 75252 Paris 05 (France); Grandjean, A. [Institut de Chimie Separative de Marcoule, UMR 5257, Laboratoire des Nanomateriaux Autoreparants, Marcoule, 30207 Bagnols-sur-Ceze (France); Dussossoy, J.L. [CEA, DEN, Laboratoire d' etude et de Developpement de Matrices de Conditionnement, Centre de Marcoule, 30207 Bagnols-sur-Ceze (France); Neuville, D.R. [Physique des Mineraux et Magmas, UMR 7047, CNRS- Institut de Physique du Globe de Paris, 7 place Jussieu, 75252 Paris 05 (France)

2008-07-01

The kinetics of sulphate departure in a sodium borosilicate melt were studied using in situ Raman spectroscopy. This technique allows the quantification of the amount of sulphate dissolved in a borosilicate glass as a function of heating time by comparison with measurements obtained by microprobe wavelength dispersive spectrometry. To quantify the sulphate content obtained with Raman spectroscopy, the integrated intensity of the sulphate band at 990 cm{sup -1} was scaled to the sum of the integrated bands between 800 and 1200 cm{sup -1}, bands that are assigned to Qn silica units on the basis of previous literature. Calibration curves were then determined for two different samples. An evaluation of the kinetics of departure of sulphate could thus be made as a function of the viscosity of the borosilicate glass, showing that the kinetics were controlled by the diffusion of sulphate and its volatilization from the melt. This experimental method allows in situ measurements of sulphate content at high temperature which cannot be obtained by any other simple technique. (authors)

Gastrointestinal tract wall visualization and distention during abdominal and pelvic multidetector CT with a neutral barium sulphate suspension: comparison with positive barium sulphate suspension and with water.

Science.gov (United States)

Oliva, M R; Erturk, S M; Ichikawa, T; Rocha, T; Ros, P R; Silverman, S G; Mortele, K J

2012-01-01

When examining patients with contrast-enhanced multidetector-row CT, we determined if the stomach and small bowel were visualized and distended better with a neutral barium sulphate suspension than with positive barium sulphate suspension or water. After obtaining approval from our institutional review board, 156 patients (women: 84; mean age: 54 yrs) with no history of gastrointestinal tract disease were randomized prospectively to receive orally either 900 ml of neutral (0.1% w/v) barium sulphate suspension (n = 53), 900 ml of positive (2.1% w/v) barium sulphate suspension (n = 53), or 900 ml of water (n = 50), prior to undergoing contrast-enhanced abdominal and pelvic multidetector-row CT. Two independent radiologists evaluated the stomach, and small bowel, for luminal distension and wall visualization, using a five point scale. Results were compared using Kruskal-Wallis and Mann-Whitney U tests. The walls of the stomach, and small bowel were visualized better in patients who were administered neutral barium sulphate suspension than those who were administered either positive barium sulphate suspension (p barium sulphate suspension, the stomach and small bowel were distended better compared to patients administered water (p barium sulphate suspension (p contrast-enhanced abdominal and pelvic multidetector-row CT, orally administered neutral barium sulphate suspension allows the gastrointestinal tract to be visualized and distended better than either positive barium sulphate suspension, or water.

Effects of agmatine sulphate on facial nerve injuries.

Science.gov (United States)

Surmelioglu, O; Sencar, L; Ozdemir, S; Tarkan, O; Dagkiran, M; Surmelioglu, N; Tuncer, U; Polat, S

2017-03-01

To evaluate the effect of agmatine sulphate on facial nerve regeneration after facial nerve injury using electron and light microscopy. The study was performed on 30 male Wistar albino rats split into: a control group, a sham-treated group, a study control group, an anastomosis group, and an anastomosis plus agmatine sulphate treatment group. The mandibular branch of the facial nerve was dissected, and a piece was removed for histological and electron microscopic examination. Regeneration was better in the anastomosis group than in the study control group. However, the best regeneration findings were seen in the agmatine sulphate treatment group. There was a significant difference between the agmatine group and the others in terms of median axon numbers (p Agmatine sulphate treatment with anastomosis in traumatic facial paralysis may enhance nerve regeneration.

Removal of cobalt and nickel from zinc sulphate solutions using activated cementation

Directory of Open Access Journals (Sweden)

Boyanov B.

2004-01-01

Full Text Available The influence of different parameters (duration, temperature, zinc dust quantity, concentration of activators - copper and antimony on the process of activated cementation of Co and Ni has been studied. We have worked with industrial zinc sulphate solutions. During the process of activated cementation of Co and Ni, copper (involved as CuSO4.5H2O and antimony (involved as Sb2O3 were used as activators. The lowest values of Co content have been obtained at a temperature of 80-85 oC, CCu = 200-300 mg/dm3 and 18 multiple surplus of zinc dust. After adding Cu to the solution, mainly the cementation of Ni is activated, and that of Co is activated to a lower degree. It was found that when GSb : GCo ratio is between 0.5 : 1 and 2 : 1, the solution is purified from Co and Ni to a great degree. After intensive stirring and increasing the duration of the process the cement sediments dissolve reversely. This holds true of Co to a greater extent, as compared to Ni. The results obtained will be used to establish optimal conditions for the carrying out of activated cementation in Zinc Production Plant in KCM SA, Plovdiv.

Copper electrodeposition from an acidic plating bath containing accelerating and inhibiting organic additives

International Nuclear Information System (INIS)

Pasquale, M.A.; Gassa, L.M.; Arvia, A.J.

2008-01-01

Copper electrodeposition on copper from still plating solutions of different compositions was investigated utilising electrochemical impedance spectroscopy (EIS), cyclic voltammetry, and scanning electron microscopy (SEM). An acid copper sulphate plating base solution was employed either with or without sodium chloride in the presence of a single additive, either polyethylene glycol (PEG) or 3-mercapto-2-propanesulphonic acid (MPSA), and their mixture. Thallium underpotential deposition/anodic stripping was employed to determine the adsorption capability of additives on copper. In the absence of chloride ions, MPSA shows a moderate adsorption on copper, whereas PEG is slightly adsorbed. At low cathodic overpotentials, the simultaneous presence of MPSA and chloride ions accelerates copper electrodeposition through the formation of an MPSA-chloride ion complex in the solution, particularly for about 220 μM sodium chloride. The reverse effect occurs in PEG-sodium chloride plating solutions. In this case, from EIS data the formation of a film that interferes with copper electrodeposition can be inferred. At higher cathodic overpotentials, when copper electrodeposition is under mass transport control, the cathode coverage by a PEG-copper chloride-mediated film becomes either partially or completely detached as the concentration of chloride ions at the negatively charged copper surface diminishes. The copper cathode grain topography at the μm scale depends on the cathodic overpotential, plating solution composition and average current density. Available data about the solution constituents and their adsorption on copper make it possible to propose a likely complex mechanism to understand copper electrodeposition from these media, including the accelerating effect of MPSA and the dynamics of PEG-copper chloride complex adsorbate interfering with the surface mobility of depositing copper ad-ions/ad-atoms

Anthropogenic influence on the distribution of tropospheric sulphate aerosol

Energy Technology Data Exchange (ETDEWEB)

Langner, J; Rodhe, H; Crutzen, P J; Zimmermann, P [Swedish Meteorological and Hydrological Institute, Norrkoeping (Sweden)

1992-10-22

Human activities have increased global emissions of sulphur gases by about a factor of three during the past century, leading to increased sulphate aerosol concentrations, mainly in the Northern Hemisphere. Sulphate aerosols can affect the climate directly, by increasing the backscattering of solar radiation in cloud-free air, and indirectly, by providing additional cloud condensation nuclei. Here a global transport-chemistry model is used to estimate the changes in the distribution of tropospheric sulphate aerosol and deposition of non-seasalt sulphur that have occurred since pre-industrial times. The increase in sulphate aerosol concentration is small over the Southern Hemisphere oceans, but reaches a factor of 100 over northern Europe in winter. Calculations indicate, however, that at most 6% of the anthropogenic sulphur emissions is available for the formation of new aerosol particles. This is because about one-half of the sulphur dioxide is deposited on the Earth's surface, and most of the remainder is oxidized in cloud droplets so that the sulphate becomes associated with pre-existing particles. Even so, the rate of formation of new sulphate particles may have doubled since pre-industrial times. 18 refs., 3 figs.

Controlling Barium Sulphate Scale Deposition Problems in an unbleached Kraft Paper Mill

CSIR Research Space (South Africa)

Sithole, Bruce

2015-06-01

Full Text Available Troubleshooting of scale deposits and defects in paper samples showed that the problem was caused by barium sulphate and calcium sulphate scales. However, it was ascertained that barium sulphate was more of a concern than calcium sulphate...

Treatment with magnesium sulphate in pre-term birth

DEFF Research Database (Denmark)

Wolf, Hans; Hegaard, H K; Greisen, G

2012-01-01

Premature birth increases a child's risk of cerebral palsy and death. The aim of this work is to investigate the association between treatment with magnesium sulphate during premature deliveries and infants' cerebral palsy and mortality through a meta-analysis of observational studies....... A comprehensive search of the Cochrane Library, EMBASE and the PubMed database from their inceptions to 1 October, 2010 using the keywords 'magnesium sulphate, children/infant/pre-term/premature and cerebral palsy/mortality/morbidity/adverse effects/outcome' identified 11 reports of observational studies. Two...... authors working independently extracted the data. A meta-analysis of the data found an association between magnesium sulphate treatment and a significantly reduced risk of mortality (RR 0.73; 95% CI 0.61-0.89) and cerebral palsy (OR 0.64; 95% CI 0.47-0.89). Antenatal treatment with magnesium sulphate...

Post traumatic tetanus and role magnesium sulphate

International Nuclear Information System (INIS)

Sikendr, R.I.; Samad, B.U.; Memon, M.I.

2009-01-01

Tetanus is a life threatening disease. Reported mortality for tetanus is 15-39%. Conventional treatment includes heavy sedation and artificial ventilation. Complications resulting from long term heavy sedation and artificial ventilation contribute to 60% of the total mortality caused by tetanus. In this study magnesium sulphate was used to reduce the need for sedation and artificial ventilation. Objectives of this prospective study were to determine the role of magnesium sulphate in post traumatic tetanus. The study was carried out in surgical Intensive Care at Pakistan Institute of Medical Sciences (PIMS), Islamabad from Jan 2004 to Dec 2007. Forty-four patients presented during this period and 33 patients were included in the study. All patients had tracheostomy done within 48 hours. Every patient was started Magnesium Sulphate therapy for control of spasms after sending baseline investigations. Patients were given ventilatory support when needed. All data was entered in well structured proforma. SPSS-10 was used to analyse data. Thirty-three patients were included in the study and all patients were given magnesium sulphate. Out of these, 45.5% cases were grade 4 tetanus, 73.6% and 63.3% cases did not require artificial ventilation and additional sedation respectively, 51.1% patients remained free of complications of tetanus. Overall mortality was 30.3%. Use of Magnesium Sulphate is safe and reduces the need for sedation and artificial ventilation in high grade tetanus thus contributing to survival benefit in adult post-traumatic tetanus cases. (author)

Copper Deficiency Leads to Anemia, Duodenal Hypoxia, Upregulation of HIF-2α and Altered Expression of Iron Absorption Genes in Mice

Science.gov (United States)

Matak, Pavle; Zumerle, Sara; Mastrogiannaki, Maria; El Balkhi, Souleiman; Delga, Stephanie; Mathieu, Jacques R. R.; Canonne-Hergaux, François; Poupon, Joel; Sharp, Paul A.; Vaulont, Sophie; Peyssonnaux, Carole

2013-01-01

Iron and copper are essential trace metals, actively absorbed from the proximal gut in a regulated fashion. Depletion of either metal can lead to anemia. In the gut, copper deficiency can affect iron absorption through modulating the activity of hephaestin - a multi-copper oxidase required for optimal iron export from enterocytes. How systemic copper status regulates iron absorption is unknown. Mice were subjected to a nutritional copper deficiency-induced anemia regime from birth and injected with copper sulphate intraperitoneally to correct the anemia. Copper deficiency resulted in anemia, increased duodenal hypoxia and Hypoxia inducible factor 2α (HIF-2α) levels, a regulator of iron absorption. HIF-2α upregulation in copper deficiency appeared to be independent of duodenal iron or copper levels and correlated with the expression of iron transporters (Ferroportin - Fpn, Divalent Metal transporter – Dmt1) and ferric reductase – Dcytb. Alleviation of copper-dependent anemia with intraperitoneal copper injection resulted in down regulation of HIF-2α-regulated iron absorption genes in the gut. Our work identifies HIF-2α as an important regulator of iron transport machinery in copper deficiency. PMID:23555700

Effects of Cuminum cyminum L. essential oil on some epididymal sperm parameters and histopathology of testes following experimentally induced copper poisoning in mice.

Science.gov (United States)

Sakhaee, E; Emadi, L; Azari, O; Kheirandish, R; Esmaili Nejad, M R; Shafiei Bafti, H

2016-06-01

Copper overload can cause sperm cell damage by inducing oxidative stress. On the other hand, cumin has a good antioxidant potential. Therefore, the aim of this study was to evaluate the effects of cumin on sperm quality and testicular tissue following experimentally induced copper poisoning in mice. Forty-eight mature male mice were divided into four equal groups as follows: group Cu which received 0.1 ml copper sulphate at dose of 100 mg kg(-1) , group Cc which received Cuminum cyminum at dose of 1 mg kg(-1) , treatment group which received copper sulphate (100 mg kg(-1) ) and treated with Cuminum cyminum (1 mg kg(-1) ), and control group which received the same volume of normal saline. Six mice in each group were sacrificed at week 4 and week 6. The results showed that sperm concentration, motility and viability in group Cu were significantly decreased at weeks 4 and 6, and severe degenerative changes were observed in testicular tissues in comparison with the control group. In treatment group, significant improvement in the sperm count, motility and viability, and normal architecture in most seminiferous tubules with organised epithelium was observed compared to the group Cu. The sperm quality parameters in the treatment group approached those of the control group. © 2015 Blackwell Verlag GmbH.

Interdependent action of nickel sulphate and X-rays on human lymphoblastoid leukeamic cells

International Nuclear Information System (INIS)

Bensimon, Jacques

1977-01-01

In a first experiment, cells were cultured in media supplemented by nickel sulphate, irradiated in same media and cultured in same media after irradiation. In a second experiment, cells were cultured during 18hrs. in media supplemented by nickel sulphate, and then cells were washed and cultured in normal media where they were irradiated. The nickel sulphate toxicity appears as a creasing function of the nickel sulphate concentration and the nickel sulphate action endurance. The nickel sulphate toxic effect is amplified by X-rays. This amplification is a time function that depends on the X-ray dose, nickel sulphate concentration and period of time from the outset of culture to the irradiation. The nickel sulphate toxic effect appears faster when nickel works after X-rays [fr

Copper wire bonding

CERN Document Server

Chauhan, Preeti S; Zhong, ZhaoWei; Pecht, Michael G

2014-01-01

This critical volume provides an in-depth presentation of copper wire bonding technologies, processes and equipment, along with the economic benefits and risks.  Due to the increasing cost of materials used to make electronic components, the electronics industry has been rapidly moving from high cost gold to significantly lower cost copper as a wire bonding material.  However, copper wire bonding has several process and reliability concerns due to its material properties.  Copper Wire Bonding book lays out the challenges involved in replacing gold with copper as a wire bond material, and includes the bonding process changes—bond force, electric flame off, current and ultrasonic energy optimization, and bonding tools and equipment changes for first and second bond formation.  In addition, the bond–pad metallurgies and the use of bare and palladium-coated copper wires on aluminum are presented, and gold, nickel and palladium surface finishes are discussed.  The book also discusses best practices and re...

Mesophilic and thermophilic anaerobic digestion of sulphate-containing wastewaters.

Science.gov (United States)

Colleran, E; Pender, S

2002-01-01

The effect of sulphate at an influent chemical oxygen demand (COD):sulphate ratio of 4 on the operational performance of anaerobic hybrid reactors treating molasses wastewater was investigated under mesophilic and thermophilic conditions in a long-term laboratory-scale study over a 1,081 day period. The presence of sulphate reduced the COD removal efficiency under both mesophilic and thermophilic conditions. At 55 degrees C, effluent acetate levels were consistently greater than 4000 mg l(-1) indicating that thermophilic acetate-utilising methane-producing bacteria (MPB) or sulphate-reducing bacteria (SRB) had not developed in the reactor under the conditions applied. At 37 degrees C, acetate was exclusively utilised by acetoclastic methanogens, whereas H2-utilising SRB predominated over H2-utilising MPB in the competition for hydrogen. By contrast, hydrogenotrophic MPB were shown to outcompete H2-utilising SRB during long-term thermophilic operation. 16SrDNA analysis of the seed sludge and reactor biomass on conclusion of the 37 degrees C and 55 degrees C trials illustrated that the dominant methanogen present on conclusion of the thermophilic trial in the absence of influent sulphate was related to Methanocorpusculum parvuum, and was capable of growth on both acetate and hydrogen. By contrast, an organism closely related to Methanobacterium thermoautotrophicum was the dominant methanogen present in the sulphate-fed reactor on completion of the thermophilic trial.

Copper oxide thin films anchored on glass substrate by sol gel spin coating technique

Science.gov (United States)

Krishnaprabha, M.; Venu, M. Parvathy; Pattabi, Manjunatha

2018-05-01

Owing to the excellent optical, thermal, electrical and photocatalytic properties, copper oxide nanoparticles/films have found applications in optoelectronic devices like solar/photovoltaic cells, lithium ion batteries, gas sensors, catalysts, magnetic storage media etc. Copper oxide is a p-type semiconductor material having a band gap energy varying from 1.2 eV-2.1 eV. Syzygium Samarangense fruit extract was used as reducing agent to synthesize copper oxide nanostructures at room temperature from 10 mM copper sulphate pentahydrate solution. The synthesized nanostructures are deposited onto glass substrate by spin coating followed by annealing the film at 200 °C. Both the copper oxide colloid and films are characterized using UV-Vis spectroscopy, field emission scanning electron microscopy (FESEM) and energy dispersive spectroscopy (EDS) techniques. Presence of 2 peaks at 500 nm and a broad peak centered around 800 nm in the UV-Vis absorbance spectra of copper oxide colloid/films is indicative of the formation of anisotropic copper oxide nanostructures is confirmed by the FESEM images which showed the presence of triangular shaped and rod shaped particles. The rod shaped particles inside island like structures were found in unannealed films whereas the annealed films contained different shaped particles with reduced sizes. The elemental analysis using EDS spectra of copper oxide nanoparticles/films showed the presence of both copper and oxygen. Electrical properties of copper oxide nanoparticles are affected due to quantum size effect. The electrical studies carried out on both unannealed and annealed copper oxide films revealed an increase in resistivity with annealing of the films.

Are high rates of sulphate reduction associated with anaerobic oxidation of methane

Energy Technology Data Exchange (ETDEWEB)

Devol, A H; Ahmed, S I

1981-01-01

Classical models of sulphur diagenesis in marine sediments are based on the assumption that the rate of sulphate reduction is first order with respect to oxidizable particulate organic carbon (POC). This assumption requires that oxidizable POC, sulphate concentration and the sulphate reduction rate be highest at the top of the sulphate reduction zone and decrease exponentially with increasing sediment depth. However, to explain recent observations of concave upwards methane distributions, the anaerobic consumption of methane has been proposed. Furthermore, it has been proposed that this consumption takes place near the bottom of the sulphate reducing zone where sulphate concentrations are low. Thus, if sulphate reducing bacteria are associated with the anaerobic oxidation of methane, a peak in sulphate reduction rate might be expected in this deep consumption zone. The importance of the process in sedimentary sulphur diagenesis is indicated by calculations estimating that 30 to 75% of the downward sulphate flux at depth may be consumed by methane oxidation within this zone. We present here profiles of sulphate reduction rate in anoxic sediments that show distinct local maxima at the depth where the anaerobic oxidation of methane would be expected. Our measurements were made during July and August 1978 in Saanich Inlet, an anoxic fjord located on the south-east of Vancouver Island, British Columbia. The inlet has a shallow sill (approx 70 m) which restricts circulation of the deeper water (maximum depth 225 m) inside the basin to the extent that for about 8 months of the year the bottom waters contain hydrogen sulphide, the inlet is an ideal location for studying sedimentary sulphate reduction because reactions with oxygen and the effects of burrowing organisms can be neglected.

Removal of radium from aqueous sulphate solutions

International Nuclear Information System (INIS)

Weir, D.R.; Masters, J.T.; Neven, M.

1983-01-01

Radium is often present in ores and an aqueous solution associated with the ore may consequently contain dissolved radium. It is frequently necessary to remove radium from such solutions to reduce the total radium content to a prescribed low level before the solution can be returned to the environment. The present invention is based on the discovery that the total radium content can be reduced to a satisfactory level within a reasonable time by adding a soluble barium salt to a radium-containing sulphate solution which also contains dissolved magnesium at a pH not greater than about 0 to precipitate radium as barium radium sulphate, raising the pH to at least 11 to precipitate an insoluble magnesium compound which collects the barium radium sulphate precipitate, and separating substantially all of the precipitates from the solution

Computerised analysis of sulphate action on model concrete piles

Digital Repository Service at National Institute of Oceanography (India)

Deshmukh, A.M.; Balasubramanian, S.; Venugopal, C.

Sulphate action severely affects the durability of marine structures. It is imperative to study precisely the effects of magnesium sulphate on pile foundations in the marine environment. In the present paper an attempt is made to assess and analyse...

Bacterial sulphate reduction and the development of alkalinity. II. Laboratory experiments with soils

Energy Technology Data Exchange (ETDEWEB)

Abd-El-Malek, Y; Rizk, S G

1963-01-01

In waterlogged soils sulphate reduction was characterized by increases in counts of sulphate reducers, and increase in titratable alkalinity, insoluble carbonate, and soluble sulphides, and a decrease in soluble Ca/sup 2 +/ + Mg/sup 2 +/. Presence of organic matter greatly enhanced sulphate reduction. A linear relationship between the amount of sulphate reduced and increases in titratable alkalinity and insoluble carbonate were apparent. The potential effects of sulphate reduction on soil fertility through the development of alkalinity are discussed.

Safety and efficacy of Bolus administration of magnesium sulphate ...

African Journals Online (AJOL)

Safety and efficacy of Bolus administration of magnesium sulphate for preeclampsia. ... On-going research is addressing its administration in terms of dosage, duration and safety. Objective: We evaluated a ... Keywords: safety, efficacy, bolus magnesium sulphate, preeclampsia, University of Benin Teaching Hospital

Kinetics and mechanism of protection of thymine from sulphate ...

Indian Academy of Sciences (India)

Unknown

The rate constant of sulphate radical anion with caffeic acid has been ... transfer of radical sites from base moiety to sugar moiety. Strand ... titrated with a standard ceric ammonium sulphate solution as reported by Kapoor et al.7. At room ...

Bacterial sulphate reduction and the development of alkalinity. I. Experiments with synthetic media

Energy Technology Data Exchange (ETDEWEB)

Abd-El-Malek, Y; Rizk, S G

1963-01-01

In liquid cultures of desulphovibrio desulphuricans the effects of the following on sulphate reduction were determined: The type of cation (ca++ or na+) attached to the sulphate ion; the presence of calcium carbonate alone and with sodium chloride; the concentration of sodium sulphate, sodium lactate and sodium chloride; and the initial pH. The titratable alkalinity formed as a result of sulphate reduction was found to be quantitatively related to the sulphate reduced, and apparently unaffected by strain variation or energy source.

Hydrogen peroxide as pre-treatment stressor in experimental immer-sion challenge of rainbow trout fry with Flavobacterium psychrophilum

DEFF Research Database (Denmark)

Henriksen, Maya Maria Mihályi; Madsen, Lone; Dalsgaard, Inger

2012-01-01

. Non-medical therapeutic substances are routinely used against pathogens in aquacultures, including copper sulphate, chloramine-T, sodium carbonates, sodium chloride, formalin and hydrogen peroxide (H2O2). One of the more successful immersion models used formalin as a stressor, but a less harmful...

Sulphate respiration from hydrogen in Desulfovibrio bacteria: a structural biology overview.

Science.gov (United States)

Matias, Pedro M; Pereira, Inês A C; Soares, Cláudio M; Carrondo, Maria Arménia

2005-11-01

Sulphate-reducing organisms are widespread in anaerobic enviroments, including the gastrointestinal tract of man and other animals. The study of these bacteria has attracted much attention over the years, due also to the fact that they can have important implications in industry (in biocorrosion and souring of oil and gas deposits), health (in inflamatory bowel diseases) and the environment (bioremediation). The characterization of the various components of the electron transport chain associated with the hydrogen metabolism in Desulfovibrio has generated a large and comprehensive list of studies. This review summarizes the more relevant aspects of the current information available on the structural data of various molecules associated with hydrogen metabolism, namely hydrogenases and cytochromes. The transmembrane redox complexes known to date are also described and discussed. Redox-Bohr and cooperativity effects, observed in a few cytochromes, and believed to be important for their functional role, are discussed. Kinetic studies performed with these redox proteins, showing clues to their functional inter-relationship, are also addressed. These provide the groundwork for the application of a variety of molecular modelling approaches to understanding electron transfer and protein interactions among redox partners, leading to the characterization of several transient periplasmic complexes. In contrast to the detailed understanding of the periplasmic hydrogen oxidation process, very little is known about the cytoplasmic side of the respiratory electron transfer chain, in terms of molecular components (with exception of the terminal reductases), their structure and the protein-protein interactions involved in sulphate reduction. Therefore, a thorough understanding of the sulphate respiratory chain in Desulfovibrio remains a challenging task.

Sulphation reactions of oxidic dust particles in waste heat boiler environment. Literature review

Energy Technology Data Exchange (ETDEWEB)

Ranki, T.

1999-09-01

Sulphation of metal oxides has an important role in many industrial processes. In different applications sulphation reactions have different aims and characteristics. In the flash smelting process sulphation of oxidic flue dust is a spontaneous and inevitable phenomena, which takes place in the waste heat boiler (WHB) when cooling down hot dust laden off-gases from sulphide smelters. Oxidic dust particles (size 0 - 50 {mu}m) react with O{sub 2} and SO{sub 2} or SO{sub 3} in a certain temperature range (500 - 800 deg C). Sulphation reactions are highly exothermic releasing large amount of heat, which affects the gas cooling and thermal performance of the boiler. Thermodynamics and kinetics of the system have to be known to improve the process and WHB operation. The rate of sulphation is affected by the prevailing conditions (temperature, gas composition) and particle size and microstructure (porosity, surface area). Some metal oxides (CuO) can react readily with SO{sub 2} and O{sub 2} and act as self-catalysts, but others (NiO) require the presence of an external catalyst to enhance the SO{sub 3} formation and sulphation to proceed. Some oxides (NiO) sulphate directly, some (CuO) may form first intermediate phases (basic sulphates) depending on the reaction conditions. Thus, the reaction mechanisms are very complex. The aim of this report was to search information about the factors affecting the dust sulphation reactions and suggested reaction mechanisms and kinetics. Many investigators have studied sulphation thermodynamics and reaction kinetics and mechanisms of macroscopical metal oxide pieces, but only few articles have been published about sulphation of microscopical particles, like dust. All the found microscale studies dealt with sulphation reactions of calcium oxide, which is not present in the flash smelting process, but used as an SO{sub 2} absorbent in the combustion processes. However, also these investigations may give some hints about the sulphation

Thermal decomposition of uranyl sulphate hydrate

International Nuclear Information System (INIS)

Sato, T.; Ozawa, F.; Ikoma, S.

1980-01-01

The thermal decomposition of uranyl sulphate hydrate (UO 2 SO 4 .3H 2 O) has been investigated by thermogravimetry, differential thermal analysis, X-ray diffraction and infrared spectrophotometry. As a result, it is concluded that uranyl sulphate hydrate decomposes thermally: UO 2 SO 4 .3H 2 O → UO 2 SO 4 .xH 2 O(2.5 = 2 SO 4 . 2H 2 O → UO 2 SO 4 .H 2 O → UO 2 SO 4 → α-UO 2 SO 4 → β-UO 2 SO 4 → U 3 O 8 . (author)

Thermometric titration of sulphate.

Science.gov (United States)

Williams, M B; Janata, J

1970-06-01

Direct thermometric titration of sulphate with a solution of barium perchlorate is proposed. The stoichiometry of the titration is shown to be critically dependent on the concentration of ethanol in the titration medium. The titration is rapid and suffers from only a few interferences.

Magnesium sulphate for fetal neuroprotection

DEFF Research Database (Denmark)

Bickford, Celeste D; Magee, Laura A; Mitton, Craig

2013-01-01

of cerebral palsy (CP) averted and quality-adjusted life years (QALYs). RESULTS: From a health system and a societal perspective, respectively, a savings of $2,242 and $112,602 is obtained for each QALY gained and a savings of $30,942 and $1,554,198 is obtained for each case of CP averted when magnesium......BACKGROUND: The aim of this study was to assess the cost-effectiveness of administering magnesium sulphate to patients in whom preterm birth at ... sensitivity analyses were used to compare the administration of magnesium sulphate with the alternative of no treatment. Two separate cost perspectives were utilized in this series of analyses: a health system and a societal perspective. In addition, two separate measures of effectiveness were utilized: cases...

Sulphate, more than a nutrient, protects the microalga Chlamydomonas moewusii from cadmium toxicity

Energy Technology Data Exchange (ETDEWEB)

Mera, Roi; Torres, Enrique, E-mail: torres@udc.es; Abalde, Julio

2014-03-01

Highlights: • Sulphate effect on cadmium toxicity in the microalga Chlamydomonas moewusii Gerloff. • Cadmium increases the sulphur requirements in Chlamydomonas moewusii. • Kinetic coefficients for sulphate utilization and cadmium effect on them. • Sulphate and cadmium influence on the biosynthesis of low-molecular mass thiols. • Cadmium toxicity reduction by sulphate due to higher biosynthesis of thiols. - Abstract: Sulphur is an essential macroelement that plays important roles in living organisms. The thiol rich sulphur compounds, such as cysteine, γ-Glu–Cys, glutathione and phytochelatins participate in the tolerance mechanisms against cadmium toxicity. Plants, algae, yeasts and most prokaryotes cover their demand for reduced sulphur by reduction of inorganic sulphate. The aim of this study was to investigate, using a bifactorial experimental design, the effect of different sulphate concentrations in the nutrient solution on cadmium toxicity in the freshwater microalga Chlamydomonas moewusii. Cell growth, kinetic parameters of sulphate utilization and intracellular concentrations of low-molecular mass thiol compounds were determined. A mathematical model to describe the growth of this microalga based on the effects of sulphate and cadmium was obtained. An ANOVA revealed an interaction between them, 16% of the effect sizes was explained by this interaction. A higher amount of sulphate in the culture medium allowed a higher cadmium tolerance due to an increase in the thiol compound biosynthesis. The amount of low-molecular mass thiol compounds, mainly phytochelatins, synthesized by this microalga was significantly dependent on the sulphate and cadmium concentrations; the higher phytochelatin content was obtained in cultures with 4 mg Cd/L and 1 mM sulphate. The maximum EC{sub 50} value (based on nominal cadmium concentration) reached for this microalga was 4.46 ± 0.42 mg Cd/L when the sulphate concentration added to the culture medium was also 1 m

Relationship between sulphate and sulphur dioxide in the air

Energy Technology Data Exchange (ETDEWEB)

Fugas, M; Gentilizza, M

1978-01-01

The relationship between the sulphate in suspended particulates and sulphur dioxide in the air was studied in various urban and industrial areas. The relationship is best described by the equation y = ax/sup b/, where y is the percentage of the sulphate S in the total S (sulphate and sulphur dioxide) and x is the concentration of the total S in the air. The regression coefficients a and b seem to be characteristics of the area. In urban areas studied so far a was between 316 and 378 and b between -0.74 and -0.83. In industrial areas polluted by dust which contains elevated concentrations of metals a was between 91 and 107 and b between -0.35 and -0.49. In the area polluted by cement dust there was practically no correlation between the sulphate S (%) and the total S, but a relatively high correlation between absolute amounts of the sulphate S and the total S. The relations indicate that the limitation of SO/sub 2/ conversion is influenced by aerosol composition. Aerosols containing certain metals may promote the conversion by a catalytic effect while alkaline substances by increasing the pH. Whether this can only happen in the plume or in the air as well remains to be clarified.

Core Sulphate-Reducing Microorganisms in Metal-Removing Semi-Passive Biochemical Reactors and the Co-Occurrence of Methanogens

Directory of Open Access Journals (Sweden)

Maryam Rezadehbashi

2018-02-01

Full Text Available Biochemical reactors (BCRs based on the stimulation of sulphate-reducing microorganisms (SRM are emerging semi-passive remediation technologies for treatment of mine-influenced water. Their successful removal of metals and sulphate has been proven at the pilot-scale, but little is known about the types of SRM that grow in these systems and whether they are diverse or restricted to particular phylogenetic or taxonomic groups. A phylogenetic study of four established pilot-scale BCRs on three different mine sites compared the diversity of SRM growing in them. The mine sites were geographically distant from each other, nevertheless the BCRs selected for similar SRM types. Clostridia SRM related to Desulfosporosinus spp. known to be tolerant to high concentrations of copper were members of the core microbial community. Members of the SRM family Desulfobacteraceae were dominant, particularly those related to Desulfatirhabdium butyrativorans. Methanogens were dominant archaea and possibly were present at higher relative abundances than SRM in some BCRs. Both hydrogenotrophic and acetoclastic types were present. There were no strong negative or positive co-occurrence correlations of methanogen and SRM taxa. Knowing which SRM inhabit successfully operating BCRs allows practitioners to target these phylogenetic groups when selecting inoculum for future operations.

Feasibility of lead removal from industrial effluents by sulphate reducing bacteria

International Nuclear Information System (INIS)

Nunez, L. A.; Diez, M.; Rodriguez, F. J.

2009-01-01

Battery manufacturing wastewater contains high concentration of sulphate and lead at low pH values. Biogical treatment by anaerobic reduction of sulphate to sulphite, with organic matter as electron donor, increases alkalinity and allow precipitating lead as sulphide. the type of organic matter, COD/SO 4 ratio and lead concentration over sulphate reduction rate are investigated in this work. (Author)

Differential responses of freshwater wetland soils to sulphate pollution

NARCIS (Netherlands)

Lamers, L.P.M.; Dolle, ten G.E.; Berg, van den S.T.G.; Delft, van S.P.J.; Roelofs, J.G.M.

2001-01-01

Sulphate (SO42-) reduction rates are generally low in freshwater wetlands and are regulated by the scarce availability of the ion. Increased concentrations of this electron acceptor due to sulphur (S) pollution of groundwater and surface water may, however, lead to high sulphate reduction rates now

The effect of magnesium on partial sulphate removal from mine water as gypsum.

Science.gov (United States)

Tolonen, Emma-Tuulia; Rämö, Jaakko; Lassi, Ulla

2015-08-15

The aim of this research was to investigate the effect of magnesium on the removal efficiency of sulphate as gypsum from mine water. The precipitation conditions were simulated with MINEQL + software and the simulation results were compared with the results from laboratory jar test experiments. Both the simulation and the laboratory results showed that magnesium in the mine water was maintaining sulphate in a soluble form as magnesium sulphate (MgSO4) at pH 9.6. Thus magnesium was preventing the removal of sulphate as gypsum (CaSO4·2H2O). However, change in the lime precipitation pH from 9.6 to 12.5 resulted in magnesium hydroxide (Mg(OH)2) precipitation and improved sulphate removal. Additionally, magnesium hydroxide could act as seed crystals for gypsum precipitation or co-precipitate sulphate further enhancing the removal of sulphate from mine water. Copyright © 2015 Elsevier Ltd. All rights reserved.

Sulphated glycosaminoglycans and proteoglycans in the developing vertebral column of juvenile Atlantic salmon (Salmo salar)

OpenAIRE

Hannesson, Kirsten O.; Ytteborg, Elisabeth; Takle, Harald; Enersen, Grethe; B?verfjord, Grete; Pedersen, Mona E.

2015-01-01

In the present study, the distribution of sulphated glycosaminoglycans (GAGs) in the developing vertebral column of Atlantic salmon (Salmo salar) at 700, 900, 1100 and 1400?d? was examined by light microscopy. The mineralization pattern was outlined by Alizarin red S and soft structures by Alcian blue. The temporal and spatial distribution patterns of different types of GAGs: chondroitin-4-sulphate/dermatan sulphate, chondroitin-6-sulphate, chondroitin-0-sulphate and keratan sulphate were add...

Microwave assisted synthesis of nano sized sulphate doped hydroxyapatite

International Nuclear Information System (INIS)

Alshemary, Ammar Z.; Goh, Yi-Fan; Akram, Muhammad; Razali, Ili Rabihah; Abdul Kadir, Mohammed Rafiq; Hussain, Rafaqat

2013-01-01

Highlights: ► Phase pure nano-sized sulphur doped hydroxyapatite has been synthesized. ► TEM analysis confirmed formation of needle shaped structure. ► Lattice parameters and cell volume increased with increase in sulphate doping. ► Crystallite size decreased as sulphate content inside the structure increased. ► Degree of crystallinity decreased with increase in sulphate substitution. - Abstract: Inorganic sulphate is required by all mammalian cells to function properly, it is the fourth most abundant anion in the human plasma. Sulphate ions are the major source of sulphur which is considered an important element for sustenance of life as it is present in the essential amino and is required by cells to function properly. In this study we have successfully substituted sulphate ions (SO 4 2− ) into hydroxyapatite (Ca 10 (PO 4 ) 6−x (SO 4 ) x (OH) 2−x ) lattice via ion exchange process with phosphate group. Concentration of SO 4 2− ions was varied between X = 0.05–0.5, using (Ca (NO 3 ) 2 ·4H 2 O), ((NH 4 ) 2 HPO 4 ) and (Na 2 SO 4 ) as starting materials. X-ray diffraction (XRD), Fourier transform IR spectroscopy (FTIR), showed that the substitution of SO 4 2− ions into the lattice resulted in peak broadening and reduced peak height due to the amorphous nature and reduced crystallinity of the resulting HA powder. Transmission electron microscopy (TEM) and field emission electron microscopy (FESEM) analysis confirmed the formation of needle shaped particles of 41 nm size with homogenous and uniform distribution of element within the HA structure

Sulphate removal from uraniferous liquors

International Nuclear Information System (INIS)

Berger, B.

1983-01-01

A process for the recovery of uranium from liquor resulting from the attack of sulphur containing uraniferous ores by an alkaline solution of sodium carbonate and/or sodium bicarbonate is claimed. An ion exchange resin is used to separate the uranium from the solution of sodium carbonate and/or bicarbonate and sodium sulphate. The ion exchange resin is then eluted with a solution of ammonium carbonate and/or bicarbonate to provide an eluate containing ammonium uranyl tricarbonate, ammonium carbonate and/or bicarbonate and ammonium sulphate. The eluate is heated to boiling to convert the ammonium uranyl tricarbonate to ammonium uranate and/or diuranate. Ammonia, carbon dioxide and water vapor are released. The precipitated ammonium uranate and/or diuranate is separated from the remaining liquor and calcined to give uranium trioxide

Serum and urinary oestrone sulphate in pregnancy and delivery measured by a direct radioimmunoassay

International Nuclear Information System (INIS)

Honjo, Hideo; Kitawaki, Jo; Itoh, Masafumi; Yasuda, Jinsuke; Yamamoto, Takara; Yamamoto, Takao; Okada, Hiroji; Ohkubo, Tadashi; Nambara, Toshio

1986-01-01

Serum and urinary levels of oestrone sulphate in pregnancy and delivery were measured by a direct radioimmunoassay without hydrolysis. the serum and urinary oestrone sulphate increased as pregnancy progressed. the mean level of serum oestrone sulphate increased to the highest peak of 494 pmol/ml at the 35th gestational week and then decreased. The mean level of urinary oestrone sulphate increased to the highest peak of 1.28 μmol/l at the 34th gestational week and the decreased. At vaginal deliveries, the mean level of maternal peripheral serum oestrone sulphate increased hourly at as high a level as 979 pmol/ml. The mean serum level of oestrone sulphate was 204 pmol/ml in the umbilical artery and 145 pmol/ml in the umbilical vein. At Caesarean section, on the other hand, the maternal peripheral serum level of oestrone sulphate averaged 362 pmol/ml. The mean serum levels of oestrone sulphate wre 90.7 pmol/ml and 171 pmol/ml in the umbilical artery and umbilical vein, respectively. These results suggest a maternal origin of oestrone sulphate in pregnancy, with fluctuations in the levels being of interest in relation to labour pain. (author)

Leaching for recovery of copper from municipal solid waste incineration fly ash: influence of ash properties and metal speciation.

Science.gov (United States)

Lassesson, Henric; Fedje, Karin Karlfeldt; Steenari, Britt-Marie

2014-08-01

Recovery of metals occurring in significant amounts in municipal solid waste incineration fly ash, such as copper, could offer several advantages: a decreased amount of potentially mobile metal compounds going to landfill, saving of natural resources and a monetary value. A combination of leaching and solvent extraction may constitute a feasible recovery path for metals from municipal solid waste incineration fly ash. However, it has been shown that the initial dissolution and leaching is a limiting step in such a recovery process. The work described in this article was focused on elucidating physical and chemical differences between two ash samples with the aim of explaining the differences in copper release from these samples in two leaching methods. The results showed that the chemical speciation is an important factor affecting the release of copper. The occurrence of copper as phosphate or silicate will hinder leaching, while sulphate and chloride will facilitate leaching. © The Author(s) 2014.

2-Mercaptobenzothiazole doped chitosan/11-alkanethiolate acid composite coating: Dual function for copper protection

International Nuclear Information System (INIS)

Bao Qi; Zhang Dun; Wan Yi

2011-01-01

Chitosan (CS) hydrogel loaded with the well-known corrosion inhibitor 2-mercaptobenzothiazole (MBT) has been introduced into a composite coating to improve copper protection. This composite coating, which has both anticorrosion and antibacterial properties, was fabricated onto the surface of copper by combining a simple self-assembled monolayer technique with a sol-gel method. The anti-corrosion ability of the coating in 3.5 wt.% NaCl solution was investigated by electrochemical methods including potentiodynamic polarization and electrochemical impedance spectroscopy. The protection efficiency of the coating is 97.70%, calculated on the basis of the corrosion current density. The stability and integrity of the composite coating were evaluated by field emission scanning electron microscopy (FESEM) and energy dispersive spectrometry (EDS). The FESEM and EDS results suggest that the composite coating endows the copper substrate with antibacterial properties, as untreated bare copper underwent microbiologically influenced corrosion in the presence of sulphate reducing bacteria (SRB). This antibacterial feature was further confirmed by the SRB culture method. In a 3.5% NaCl solution and highly corrosive SRB culture media, the as-prepared CS based composite coating gave corrosion protection by exhibiting better barrier effects against the attack of aggressive environments.

The hypobranchial mucin of the whelk Buccinum undatum L. The polysaccharide sulphate component.

Science.gov (United States)

Hunt, S; Jevons, F R

1966-02-01

1. A polysaccharide sulphate has been isolated from the hypobranchial mucin of the whelk Buccinum undatum. 2. The molecular weight of this polysaccharide, which is a glucan carrying one ester sulphate group per monosaccharide residue, is 1.7x10(5). 3. Some investigations bearing on the location of the ester sulphate groups are reported. 4. The viscosity of the whole mucin has been shown to depend mainly on the glucan sulphate.

Microwave assisted synthesis of nano sized sulphate doped hydroxyapatite

Energy Technology Data Exchange (ETDEWEB)

Alshemary, Ammar Z.; Goh, Yi-Fan; Akram, Muhammad; Razali, Ili Rabihah [Department of Chemistry, Faculty of Science, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor Darul Ta’zim (Malaysia); Abdul Kadir, Mohammed Rafiq [Medical Implant Technology Group, Faculty of Biomedical Engineering and Health Science, Universiti Teknologi Malaysia,81310 UTM Skudai, Johor Darul Ta’zim (Malaysia); Hussain, Rafaqat, E-mail: rafaqat@kimia.fs.utm.my [Ibnu Sina Institute for Fundamental Science Studies, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor DarulTa’zim (Malaysia)

2013-06-01

Highlights: ► Phase pure nano-sized sulphur doped hydroxyapatite has been synthesized. ► TEM analysis confirmed formation of needle shaped structure. ► Lattice parameters and cell volume increased with increase in sulphate doping. ► Crystallite size decreased as sulphate content inside the structure increased. ► Degree of crystallinity decreased with increase in sulphate substitution. - Abstract: Inorganic sulphate is required by all mammalian cells to function properly, it is the fourth most abundant anion in the human plasma. Sulphate ions are the major source of sulphur which is considered an important element for sustenance of life as it is present in the essential amino and is required by cells to function properly. In this study we have successfully substituted sulphate ions (SO{sub 4}{sup 2−}) into hydroxyapatite (Ca{sub 10}(PO{sub 4}){sub 6−x}(SO{sub 4}){sub x}(OH){sub 2−x}) lattice via ion exchange process with phosphate group. Concentration of SO{sub 4}{sup 2−} ions was varied between X = 0.05–0.5, using (Ca (NO{sub 3}){sub 2}·4H{sub 2}O), ((NH{sub 4}){sub 2}HPO{sub 4}) and (Na{sub 2}SO{sub 4}) as starting materials. X-ray diffraction (XRD), Fourier transform IR spectroscopy (FTIR), showed that the substitution of SO{sub 4}{sup 2−} ions into the lattice resulted in peak broadening and reduced peak height due to the amorphous nature and reduced crystallinity of the resulting HA powder. Transmission electron microscopy (TEM) and field emission electron microscopy (FESEM) analysis confirmed the formation of needle shaped particles of 41 nm size with homogenous and uniform distribution of element within the HA structure.

Characteristics and antioxidant of Ulva intestinalis sulphated polysaccharides extracted with different solvents.

Science.gov (United States)

Peasura, Napassorn; Laohakunjit, Natta; Kerdchoechuen, Orapin; Wanlapa, Sorada

2015-11-01

Ulva intestinalis, a tubular green seaweed, is a rich source of nutrient, especially sulphated polysaccharides. Sulphated polysaccharides from U. intestinalis were extracted with distilled water, 0.1N HCl, and 0.1N NaOH at 80°C for 1, 3, 6, 12, and 24h to study the effect of the extraction solvent and time on their chemical composition and antioxidant activity. Different types of solvents and extraction time had a significant influence on the chemical characteristics and antioxidant activity (pMonosaccharide composition and FT-IR spectra analyses revealed that sulphated polysaccharides from all solvent extractions have a typical sugar backbone (glucose, rhamnose, and sulphate attached at C-2 or C-3 of rhamnose). Sulphated polysaccharides extracted with acid exhibited greater antioxidant activity than did those extracted with distilled water and alkali. The results indicated that solvent extraction could be an efficacious method for enhancing antioxidant activity by distinct molecular weight and chemical characteristic of sulphated polysaccharides. Copyright © 2015 Elsevier B.V. All rights reserved.

Dose-response testing with nickel sulphate using the TRUE test in nickel-sensitive individuals. Multiple nickel sulphate patch-test reactions do not cause an 'angry back'

DEFF Research Database (Denmark)

Andersen, Klaus Ejner; Lidén, C; Hansen, J

1993-01-01

The aim of this study was to employ the TRUE test assay to confirm the presence or absence of the 'angry back' phenomenon, i.e. that a strong positive patch-test reaction heightens adjacent patch-test response. In addition, we wished to establish the dose-response relationship for nickel sulphate...... back' phenomenon was not apparent in this study, as the spill-over effect was not statistically significant. Strong reactions to high concentrations of nickel sulphate did not enhance the response to adjacent lower concentrations of nickel sulphate....

Dietary copper effects survival of channel catfish challenged with Flavobacterium columnare

Science.gov (United States)

Columnaris disease is one of the most important bacterial diseases of channel catfish, Ictalurus punctatus, commercially grown in the US. Copper sulfate (CuSO4) has also been shown to be both therapeutic and prophylactic as a water treatment for columnaris disease. As copper is an essential dietar...

Corrosion Performance of Inconel 625 in High Sulphate Content

Science.gov (United States)

Ismail, Azzura

2016-05-01

Inconel 625 (UNS N06625) is a type of nickel-chromium-molybdenum alloy with excellent corrosion resistance in a wide range of corrosive media, being especially resistant to pitting and crevice corrosion. However, in aggressive environment, Inconel 625 will suffer corrosion attack like other metals. This research compared the corrosion performance of Inconel 625 when exposed to higher sulphate content compared to real seawater. The results reveal that Inconel 625 is excellent in resist the corrosion attack in seawater. However, at increasing temperature, the corrosion resistance of this metal decrease. The performance is same in seawater with high sulphate content at increasing temperature. It can be concluded that sulphate promote perforation on Inconel 625 and become aggressive agents that accelerate the corrosion attack.

Effects of Copper-based Compounds, Antibiotics and a Plant Activator on Population Sizes and Spread of Clavibacter michiganensis subsp. michiganensis in Greenhouse Tomato Seedlings

Directory of Open Access Journals (Sweden)

Svetlana Milijašević

2009-01-01

Full Text Available Three copper-based compounds (copper hydroxide, copper oxychloride, copper sulphate, two antibiotics (streptomycin and kasugamycin and a plant activator (ASM significantly reduced population sizes and spread of C. michiganensis subsp. michiganensis among tomatoseedlings in the greenhouse. Streptomycin had the best effect in reducing pathogen population size in all sampling regions. Moreover, this antibiotic completely stopped the spread of C. michiganensis subsp. michiganensis in the region most distant from the inoculumfocus. Copper hydroxide mixed with streptomycin significantly limited the pathogen population, compared with copper hydroxide alone, the other copper-based compounds, ASM and kasugamycin. However, combining streptomycin with copper hydroxide did notcontribute to its greater efficacy against the pathogen population. Copper-based compounds, in general, were less effective in limiting pathogen population sizes than the other treatments in all three sampling regions, primarily copper oxychloride and the combinationof copper hydroxide and mancozeb. Among copper compounds, copper hydroxide was the most prominent in reducing the bacterial population, especially in the region closest to the inoculum focus, while its combination with mancozeb did not improve the effects. Kasugamycin significantly limited pathogen population size, compared to copper bactericides, but it was less effective than the other antibiotic compound, i.e. streptomycin. The plant activator ASM significantly reduced population density, and it was more effectivewhen used three days prior to inoculation than six days before inoculation.

Synthesis and thermal behavior of double copper and potassium pyrophosphate

International Nuclear Information System (INIS)

Ciopec, Mihaela; Muntean, Cornelia; Negrea, Adina; Lupa, Lavinia; Negrea, Petru; Barvinschi, Paul

2009-01-01

This paper presents the synthesis and thermal behavior of double copper and potassium pyrophosphate, which can be used as a PK fertilizer containing copper as micronutrient. In order to find the conditions for the synthesis of this compound from copper sulphate and potassium pyrophosphate, various Cu 2+ :P 2 O 7 4- molar ratios (0:1-2:1), various molar concentrations of the solutions (0.075; 0.1; 0.15 and 0.2 mol L -1 ) and various temperatures (25, 50, 75 and 100 o C) have been used. The solid product synthesized in optimum conditions for the separation of micronutrient copper from the reaction mass (Cu 2+ :P 2 O 7 4- molar ratio 1:1, concentration 0.1 mol L -1 ) was subjected to a complex study: chemical analysis, thermal analysis, energy dispersive X-ray spectroscopy, scanning electron microscopy and X-ray diffractometry. During heating up to 1000 o C, K 2 Cu 3 (P 2 O 7 ) 2 .3H 2 O loses the crystallization water; several transformations of the phosphates also take place: the decomposition of pyrophosphates to ortho-phosphates; the transformation of ortho-phosphates; the polymerization of a fraction of ortho-phosphates to amorphous phosphates with longer chains; the reorganization of ortho-phosphates and poly-phosphates to pyrophosphates and their crystallization. The decomposition mechanism was confirmed when using the X-ray diffraction patterns of the compound, thermally treated at several temperatures.

Study of the sulphate expansion phenomenon in concrete: behaviour of the cemented radioactive wastes containing sulphate

International Nuclear Information System (INIS)

Li, Guanshu

1994-01-01

Sulphate attack is one of the major degradation processes of concrete. It is especially important in storing cemented radioactive wastes containing sulphate. In this thesis, we have thoroughly investigated the degradation mechanisms of cemented radioactive wastes by sulphate. The CaO-Al 2 O 3 -SO 3 -H 2 O systems with and without alkalis are studied. For the system without alkalis, experimental results show that it is the formation of a secondary ettringite under external water supply by steric effect that causes the expansion. For the system with alkalis, the ettringite does not appear while a new mineral called 'U', a sodium-substituted AFm phase is detected. This phase is shown to be responsible for the expansion and destruction of the specimens. The conditions for the formation, the product of solubility and many means of its synthesis are discussed, and a complete list of the inter-reticular distances file is given. The behaviour of the different types of cemented wastes containing sulphate are then studied with a special focus on the U phase on entity which was heretofore very little understood. The following three hypothetical mechanisms of sulphate expansion are proposed: the formation of the secondary U phase, the transformation of the U phase to the ettringite and the topochemical hydration of thenardite into mirabilite. Experiments on a simplified system have demonstrated clearly that the formation of the secondary U phase can induce enormous expansion by steric effect, this justifying the first assumption. Simulation by the mass and volume balances is carried out thereafter and enables us to estimate the expansion induced by the formation of the secondary U phase in the cemented wastes. The second assumption is also well verified by a series of leaching tests in different solutions on mixtures containing the U phase. On the basis of the analysis of the specimens under leaching, it has been assumed that the expansion is associated with the

The effect of water on the sulphation of limestone

Energy Technology Data Exchange (ETDEWEB)

Chunbo Wang; Lufei Jia; Yewen Tan; E.J. Anthony [North China Electric Power University, Baoding City (China). School of Energy and Power Engineering

2010-09-15

A series of tests was conducted in a thermogravimetric analyzer (TGA) to study the sulphation behaviour of limestone in the presence of water over the temperature range of 800-850{sup o}C. Four different Canadian limestones, all with a particle size range of 75-425 {mu}m, were sulphated using a synthetic flue gas with a composition of 15% CO{sub 2}, 3% O{sub 2}, 0% or 10% H{sub 2}O, 1750 ppm SO{sub 2} and the balance N{sub 2}. Water was shown to have a significant promotional effect on sulphation, especially in the diffusion-controlled stage. However, the effect of water during the kinetic-controlled stage appeared to be much less pronounced. Based on these results, it is proposed that the presence of water leads to the transient formation of Ca(OH){sub 2} as an intermediate, which in turn reacts with SO{sub 2} at a faster rate than CaO does. Alternatively stated, it appears that H{sub 2}O acts as catalyst for the sulphation reaction of CaO. 30 refs., 8 figs., 3 tabs.

The action of diazoxide and minoxidil sulphate on rat blood vessels: a comparison with cromakalim.

Science.gov (United States)

Newgreen, D. T.; Bray, K. M.; McHarg, A. D.; Weston, A. H.; Duty, S.; Brown, B. S.; Kay, P. B.; Edwards, G.; Longmore, J.; Southerton, J. S.

1990-01-01

1. The actions of diazoxide and minoxidil sulphate have been compared with those of cromakalim in rat aorta and portal vein. 2. Diazoxide and minoxidil sulphate hyperpolarized the rat portal vein in a similar manner to cromakalim. 3. Cromakalim, diazoxide and minoxidil sulphate increased 42K and 86Rb efflux from rat portal vein, although minoxidil sulphate had only a small effect on 86Rb efflux. 4. Cromakalim, diazoxide and minoxidil sulphate increased 42K efflux from rat aorta but only cromakalim and diazoxide increased 86Rb efflux from this tissue. 5. Glibenclamide inhibited the relaxant actions of cromakalim, diazoxide and minoxidil sulphate on rat aorta and the increase in 42K efflux produced by these agents in this tissue. 6. Diazoxide relaxed an 80 mM KCl-induced contraction of rat aorta, whilst cromakalim and minoxidil sulphate were without effect. 7. Cromakalim, diazoxide and minoxidil sulphate had no effect on cyclic AMP or cyclic GMP concentrations in rat aorta. 8. It is concluded that diazoxide and minoxidil sulphate like cromakalim exhibit K+ channel opening properties in vascular smooth muscle. Diazoxide exerts an additional inhibitory action not related to the production of cyclic AMP or cyclic GMP. The action of minoxidil sulphate may be primarily located at a K+ channel which is relatively impermeable to 86Rb. PMID:2167738

ENVIRONMENTAL RISK ASSESSMENT OF SOME COPPER BASED FUNGICIDES ACCORDING TO THE REQUIREMENTS OF GOOD LABORATORY PRACTICE

Directory of Open Access Journals (Sweden)

Marga GRĂDILĂ

2015-10-01

Full Text Available The paper presents data demonstrating the functionality of biological systems reconstituted with aquatic organisms developed under Good Laboratory Practice testing facility within Research - Development Institute for Plant Protection Bucharest for environmental risk assessment of four fungicides based on copper, according to Good Laboratory Practice requirements. For risk assessment, according to GLP were made the following steps: Good Laboratory Practice test facility was established, we have ensured adequate space for growth, acclimatization and testing for each test species, it was installed a complex water production instalation needed to perform tests, it was achieved control system for checking environmental conditions and have developed specific operating procedures that have been accredited according to Good Laboratory Practice.The results showed that biological systems model of the Good Laboratory Practice test facility in Research - Development Institute for Plant Protection meet the requirements of Organisation for Economic Co-operation and Development Guidelines regarding GLP, and after testing copper-based fungicides in terms of acute toxicity Cyprinus carpio and to Daphnia magna revealed that three of them (copper oxychloride, copper hydroxide and copper sulphate showed ecological efficiency, ie low toxicity. Metallic copper based fungicides showed a higher toxicity, resulting in fish toxicity symptoms: sleep, sudden immersion, faded, weakness, swimming in spiral, lack of balance, breathing slow and cumbersome, spasms and mortality.

Blood biochemical changes in common carp (Cyprinus carpio Linnaeus, 1758 fed different levels of copper sulphate and zeolite

Directory of Open Access Journals (Sweden)

Arzu Aydın Uncumusaoğlu

2018-02-01

Full Text Available In this study, copper toxicity, was investigated after the addition of zeolite to the diet of common carps (Cyprinus carpio. The experiment included four groups with three replicates each. The 4 group feeds were [CuSO4; CuSO4 + Zeolite; Zeolite, and the control without CuSO4 or Zeolite with three replicates each. Fishes were kept in 80 L glass aquariums with 10 fishes with a mean weight of 60.6 ± 0.2 g. At the end of each period, a necropsy was performed on fishes from each treatment, and gross clinical signs were recorded. We found significant changes in the blood parameters of the common carps with or without different levels of zeolite and copper. Changes in cholesterol (CHOL, triglyceride (TG, low density lipoprotein (LDL, alanine aminotransferase (ALT, aspartate aminotransferase (AST, alkaline phosphatase (ALP, calcium (Ca2+, phosphorus (P+, sodium (Na+, potassium (K+, chloride (Cl-, magnesium (Mg2+, and ferrous (Fe+2 were also significant. Our results suggest that zeolite can be used in fish feeds at a rate of 40 mg/l to mitigate the toxic effects of copper.

Magnesium sulphate and other anticonvulsants for women with pre-eclampsia.

Science.gov (United States)

Duley, Lelia; Gülmezoglu, A Metin; Henderson-Smart, David J; Chou, Doris

2010-11-10

Eclampsia, the occurrence of a seizure (fit) in association with pre-eclampsia, is rare but potentially life-threatening. Magnesium sulphate is the drug of choice for treating eclampsia. This review assesses its use for preventing eclampsia. To assess the effects of magnesium sulphate, and other anticonvulsants, for prevention of eclampsia. We searched the Cochrane Pregnancy and Childbirth Group's Trials Register (4 June 2010), and the Cochrane Central Register of Controlled Trials Register (The Cochrane Library 2010, Issue 3). Randomised trials comparing anticonvulsants with placebo or no anticonvulsant, or comparisons of different drugs, for pre-eclampsia. Two authors assessed trial quality and extracted data independently. We included 15 trials. Six (11,444 women) compared magnesium sulphate with placebo or no anticonvulsant: magnesium sulphate more than a halved the risk of eclampsia (risk ratio (RR) 0.41, 95% confidence interval (CI) 0.29 to 0.58; number needed to treat for an additional beneficial outcome (NNTB) 100, 95% CI 50 to 100), with a non-significant reduction in maternal death (RR 0.54, 95% CI 0.26 to 1.10) but no clear difference in serious maternal morbidity (RR 1.08, 95% CI 0.89 to 1.32). It reduced the risk of placental abruption (RR 0.64, 95% CI 0.50 to 0.83; NNTB 100, 95% CI 50 to 1000), and increased caesarean section (RR 1.05, 95% CI 1.01 to 1.10). There was no clear difference in stillbirth or neonatal death (RR 1.04, 95% CI 0.93 to 1.15). Side effects, primarily flushing, were more common with magnesium sulphate (24% versus 5%; RR 5.26, 95% CI 4.59 to 6.03; number need to treat for an additional harmful outcome (NNTH) 6, 95% CI 5 to 6).Follow-up was reported by one trial comparing magnesium sulphate with placebo: for 3375 women there was no clear difference in death (RR 1.79, 95% CI 0.71 to 4.53) or morbidity potentially related to pre-eclampsia (RR 0.84, 95% CI 0.55 to 1.26) (median follow-up 26 months); for 3283 children exposed in utero

Performance of cement solidification with barium for high activity liquid waste including sulphate

International Nuclear Information System (INIS)

Waki, Toshikazu; Yamada, Motoyuki; Horikawa, Yoshihiko; Kaneko, Masaaki; Saso, Michitaka; Haruguchi, Yoshiko; Yamashita, Yu; Sakai, Hitoshi

2009-01-01

The target liquid waste to be solidified is generated from PWR primary loop spent resin treatment with sulphate acid, so, its main constituent is sodium sulphate and the activity of this liquid is relatively high. Waste form of this liquid waste is considered to be a candidate for the subsurface disposal. The disposed waste including sulphate is anticipated to rise a concentration of sulphate ion in the ground water around the disposal facility and it may cause degradation of materials such as cement and bentonite layer and comprise the disposal facility. There could be two approaches to avoid this problem, the strong design of the disposal facility and the minimization of sulphaste ion migration from the solidified waste. In this study, the latter approach was examined. In order to keep the low concentration of sulphate ion in the ground water, it is effective to make barium sulphate by adding barium compound into the liquid waste in solidification. However, adding equivalent amount of barium compound with sulphate ion causes difficulty of mixing, because production of barium sulphate causes high viscosity. In this study, mixing condition after and before adding cement into the liquid waste was estimated. The mixing condition was set with consideration to keep anion concentration low in the ground water and of mixing easily enough in practical operation. Long term leaching behavior of the simulated solidified waste was also analyzed by PHREEQC. And the concentration of the constitution affected to the disposal facility was estimated be low enough in the ground water. (author)

Activity and deactivation of sulphated TiO2- and ZrO2-based V, Cu, and Fe oxide catalysts for NO abatement in alkali containing flue gases

DEFF Research Database (Denmark)

Kustov, Arkadii; Rasmussen, Søren Birk; Fehrmann, Rasmus

2007-01-01

Vanadia, copper and iron oxide catalysts supported on conventional TiO2, ZrO2, and sulphated-TiO2 and ZrO2 have been prepared. These catalysts were characterized by elemental analysis, N-2-BET, XRD, and NH3-TPD methods. The influence of potassium oxide additives on the acidity and activity...... of the catalysts with potassium leads to a considerable decrease of their catalytic activity. In the case of the traditional carriers (TiO2, ZrO2), the poisoning of the catalyst with small amounts of potassium oxide (K/metal ratio...

Effect of temperature on sulphate reduction, growth rate and growth yield in five psychrophilic sulphate-reducing bacteria from Arctic sediments

DEFF Research Database (Denmark)

Knoblauch, C.; Jørgensen, BB

1999-01-01

Five psychrophilic sulphate-reducing bacteria (strains ASv26, LSv21, PSv29, LSv54 and LSv514) isolated from Arctic sediments were examined for their adaptation to permanently low temperatures, All strains grew at -1.8 degrees C, the freezing point of sea water, but their optimum temperature...... and T(opt). For strains LSv21 and LSv514, however, growth yields were highest at the lowest temperatures, around 0 degrees C. The results indicate that psychrophilic sulphate-reducing bacteria are specially adapted to permanently low temperatures by high relative growth rates and high growth yields...... at in site conditions....

Complete sulphate removal from neutralised acidic mine drainage with barium carbonate

CSIR Research Space (South Africa)

Swanepoel, H

2012-03-01

Full Text Available -barium-calcium) Desalination process which uses barium salts to further reduce the sulphate concentration to acceptable levels with the added advantage that sulphate removal can be controlled due to the low solubility of BaSO4. This paper reports on the results...

Stream plant chemistry as indicator of acid sulphate soils in Sweden

Directory of Open Access Journals (Sweden)

K. LAX

2008-12-01

Full Text Available Results from the biogeochemical mapping (roots of aquatic plants and Fontinalis antipyretica conducted by the Geological Survey of Sweden (SGU reflects the metal load of surface waters draining acid sulphate (AS soils in Sweden. In this study, results from the biogeochemical, soil geochemical and Quaternary mapping programmes at SGU were used to investigate the impact of fine-grained deposits hosting AS soils on stream water trace element chemistry in two separate areas. In the area around Lake Mälaren, postglacial sediments contain the highest levels of most trace elements studied. Owing to the low pH of AS soils and subsequent leaching, levels of nickel (Ni, cobalt (Co, copper (Cu, sulphur (S, yttrium (Y, uranium (U, tungsten (W, and molybdenum (Mo were significantly elevated in aquatic roots. Levels were lower in the Skellefteå area, which may be explained by lower concentrations in source deposits. Concentrations of arsenic (As and lead (Pb were normal or impoverished in biogeochemical samples from postglacial, finegrained sediment areas. Maps based on ratios (Ni:Pb or Y:Pb in biogeochemical samples can, together with results from Quaternary mapping, be used to predict areas with AS soils in Sweden.;

Development of melt compositions for sulphate bearing high level waste

International Nuclear Information System (INIS)

Jahagirdar, P.B.; Wattal, P.K.

1997-09-01

The report deals with the development and characterization of vitreous matrices for sulphate bearing high level waste. Studies were conducted in sodium borosilicate and lead borosilicate systems with the introduction of CaO, BaO, MgO etc. Lead borosilicate system was found to be compatible with sulphate bearing high level wastes. Detailed product evaluation carried on selected formulations is also described. (author)

Aspergillus fumigatus Copper Export Machinery and Reactive Oxygen Intermediate Defense Counter Host Copper-Mediated Oxidative Antimicrobial Offense

Directory of Open Access Journals (Sweden)

Philipp Wiemann

2017-05-01

Full Text Available The Fenton-chemistry-generating properties of copper ions are considered a potent phagolysosome defense against pathogenic microbes, yet our understanding of underlying host/microbe dynamics remains unclear. We address this issue in invasive aspergillosis and demonstrate that host and fungal responses inextricably connect copper and reactive oxygen intermediate (ROI mechanisms. Loss of the copper-binding transcription factor AceA yields an Aspergillus fumigatus strain displaying increased sensitivity to copper and ROI in vitro, increased intracellular copper concentrations, decreased survival in challenge with murine alveolar macrophages (AMΦs, and reduced virulence in a non-neutropenic murine model. ΔaceA survival is remediated by dampening of host ROI (chemically or genetically or enhancement of copper-exporting activity (CrpA in A. fumigatus. Our study exposes a complex host/microbe multifactorial interplay that highlights the importance of host immune status and reveals key targetable A. fumigatus counter-defenses.

Differential inhibition of polymorphonuclear leukocyte recruitment in vivo by dextran sulphate and fucoidan

Directory of Open Access Journals (Sweden)

N. Van Osselaer

1996-01-01

Full Text Available The selectin-mediated rolling of leukocytes along the endothelial cells is a prerequisite step followed by firm adhesion and extravasation into the inflamed tissue. This initial contact can be suppressed by sulphated polysaccharides. We have studied the effect of sulphated polysaccharides on the ultimate polymorphonuclear leukocyte (PMN recruitment and plasma leakage in rabbit skin in response to intradermal injection of various inflammatory mediators. PMN infiltration evoked by various PMN chemoattractants (FMLP, C5a desArg, LTB4 and IL-8 was significantly inhibited after intravenous injection of dextran sulphate (25 mg/kg, heparin (2 × 90 mg/kg or fucoidan (1 mg/kg. PMN-dependent plasma leakage was equally well reduced by the different sulphated polymers. Vascular permeability induced by histamine or thrombin acting via a PMN-independent mechanism was not reduced. Fucoidan was the only polysaccharide able to suppress IL-1-induced PMN infiltration for 60–70%. Local administration of dextran sulphate had no effect on PMN-dependent plasma leakage. Differential inhibition of PMN recruitment was determined after injection of dextran sulphate or fucoidan depending on the type of insult. Therefore, these results suggest that different adhesion pathways are utilized during PMN recruitment in vivo in response to chemoattractants and IL-1.

Corrosivity Index Copper and Steel at Two Locations in Villahermosa, Tabasco

Directory of Open Access Journals (Sweden)

Tejero-Rivas María Candelaria

2015-03-01

Full Text Available This paper presents a study of the atmospheric corrosion of copper and carbon steel made ​​in two environments Villahermosa, Tabasco for six months. The test site of the industrial zone started Villahermosa Institute of Technology (ITVH and rural-urban site at the Technological University of Tabasco (UTTAB. Aluminum in combination with a screw carbon steel provided the index marine corrosivity (MA, the brass screw gives the index of industrial corrosivity (IA; wire method of screw according to ASTM G116-93 was used and the plastic screw nylon gives the rate of rural-urban corrosivity (RUA. The determination of air pollutants (sulfur dioxide and chlorides, was with the methods of wet candle and sulfation plates according to ISO 9225. Morphology studies were performed on the corrosion products formed on the specimens screw, using scanning electron microscopy coupled with energy dispersive. The corrosion products that formed on the surface of copper and carbon steel, having a bulb-shaped morphology characteristic of the addition of soluble salts, particularly sulphates and chlorides, were identified in the two stations.

Influence on ammonium-sulphate fertilizer on P-uptake by upland rice

International Nuclear Information System (INIS)

Abdullah, N; Mitrosuhardjo, M.M.

1988-01-01

A greenhouse experiment to study the influence of ammonium -sulphate fertilizer on P-uptake by Atomita I/1 rice variety on latosol soil of Pasar Jumat has been conducted. Factorial experiment consisting of eight treatments was arrange in a fully randomized design. Each treatment was replicated three times. The rate of ammonium sulphate fertilizer was equivalent to 0, 30, 60, and 90 kg N/ha, and TSP at the rate of 90 and 180 kg P/ha. Ammonium sulphate fertilizer with 2% atom 15-N and TSP with specific activity of 0.2 mCi/g P2O5 were used in the experiment. The plant was harvested 70 days after planting, It was turned out that ammonium sulphate fertilizer gave a highly significant difference (p=<0.01) of dry weight of plant. The rate of TSP did not effect significantly on plant dry weight. Ammonium sulphate fertilizer gave highly significant difference on P-uptake. Fertilizer use efficiency was in the range of 3.88 - 6.60% for 90 kg P and 2.51 - 4.46% for 180 kg P. Fertilizer-N uptake was significantly increased (p=<0.05) with the increase of N rate. Rate of fertilizer-N use efficiency was in the range of 47-60% of the applied fertilizer. (authors). 4 refs, 9 tabs

Influence of the Interaction between Sphalerite and Pyrite on the Copper Activation of Sphalerite

Directory of Open Access Journals (Sweden)

Bo Yang

2018-01-01

Full Text Available In this paper, the effect of pyrite on the activation of sphalerite was investigated by micro-flotation, copper adsorption experiments, X-ray photoelectron spectroscopy (XPS, and electrochemical measurement. The micro-flotation test results showed that the recovery and flotation rate of sphalerite with copper sulphate as activator and butyl xanthate as collector were significantly decreased with the increasing content of pyrite in pulp. Cu2+ adsorption results indicated that the adsorption of Cu2+ on the sphalerite surface were decreased when pyrite was present in the pulp. XPS surface analysis demonstrated that the proportion of Cu+ species increased in the activation products on the sphalerite surface, but the total atomic concentration of Cu atom was decreased. Linear voltammetry measurement suggested that the current density of Cu+ species oxidizing to Cu2+ species was increased when sphalerite was electrically contacted with pyrite, which confirmed the increased proportion of Cu+ species on Cu-activation sphalerite surface when contacting with pyrite. These results indicated that there is not only a competitive adsorption for cupric ions (Cu2+, but the galvanic interaction between sphalerite and pyrite also has a significant influence on the copper activation of sphalerite.

Tyrosine sulphation is not required for microvillar expression of intestinal aminopeptidase N

DEFF Research Database (Denmark)

Danielsen, E M

1988-01-01

incorporation of [35S]sulphate into aminopeptidase N and other major microvillar hydrolases by 70-85% compared with controls, indicating an inhibition of their post-translational tyrosine sulphation. In labelling experiments with [35S]methionine from 0.5 to 5 h, DCNP was tested for its possible influence...... on synthesis, processing and microvillar expression of aminopeptidase N, but no effect on any of these parameters could be detected. It can therefore be concluded that tyrosine sulphation is not required (for instance as a sorting signal) for the targeting of newly synthesized enzymes to the microvillar...

Challenges regarding the start-up of an anaerobic biological sulphate reactor using H2 and CO2 as electron donor and carbon sources

CSIR Research Space (South Africa)

Roux, SP

2009-05-01

Full Text Available Include neutralization and chemical precipitation as well as membrane dependent processes. Biological sulphate reduction is another, environmentally benign option but relies heavily on the availability of an economically viable electron donor...

Oxygen isotopic composition of sulphates from some mineral waters and mine waters in western Bohemia

International Nuclear Information System (INIS)

Smejkal, V.

1979-01-01

Two main genetic types of sulphate can be distinguished according to the delta 18 O(SO 4 2- ) measurements in sulphate-rich mineral and mine waters of western Bohemia - sulphates in descending mine waters and in weathered outcrops of graphitic pyrite slates from areas outside Tertiary basins, which originated in recent time by the oxidation of sulphides in the presence of atmospheric oxygen, have delta 18 O values from -2.1 to -6.1 per mille SMOW; and sulphates from springs of mineral waters of the renowned spas of Karlovy Vary, Frantiskovy Lazne and Marianske Lazne show distinctly heavier delta 18 O values - from +4.0 to +6.4 per mille, with maximum of values between +5.0 and +6.0 per mille. Similar delta 18 O values have been established in thenardites and in gypsum in Miocene claystones and in sulphates of some mine waters in the nearby Tertiary Cheb and Sokolov Basins. The presented results indicate that sulphates in mineral waters of the Karlovy Vary type originate mainly by leaching of Miocene sulphates and not by present-day oxidation of sulphidic sulphur. (author)

Possibilities of Sulphate Elimination from Mine Water

Directory of Open Access Journals (Sweden)

Heviánková Silvie

2004-12-01

Full Text Available The issue of „acid water“ (or AMD is well known in the world for some centuries. In the Eastern Slovakia, the most acid surface water occurs in the area of old mine Smolník, which is closed and submerged for 15 years. The submitted contribution deals with the sulphate-elimination from this locality. Recently, several methods of sulphate-elimination from the mine water are applied. The best-known methods are biological, physical-chemical and chemical precipitation. The method described in this contribution consists of chemical precipitation by sodium aluminate and calcium hydrate. Under application of this method very interesting results were obtained. The amount of SO42- anions decreased to almost zero-value, using optimal doses of the chemical reagents.

The Metal And Sulphate Removal From Mine Drainage Waters By Biological-Chemical Ways

Directory of Open Access Journals (Sweden)

Jenčárová Jana

2015-06-01

Full Text Available Mine drainage waters are often characterized by high concentrations of sulphates and metals as a consequence of the mining industry of sulphide minerals. The aims of this work are to prove some biological-chemical processes utilization for the mine drainage water treatment. The studied principles of contamination elimination from these waters include sulphate reduction and metal bioprecipitation by the application of sulphate-reducing bacteria (SRB. Other studied process was metal sorption by prepared biogenic sorbent. Mine drainage waters from Slovak localities Banská Štiavnica and Smolník were used to the pollution removal examination. In Banská Štiavnica water, sulphates decreased below the legislative limit. The elimination of zinc by sorption experiments achieved 84 % and 65 %, respectively.

Volcanic lake systems as terrestrial analogue for sulphate-rich terrains on Mars

NARCIS (Netherlands)

Rodríguez, A.

2016-01-01

Remote-sensing observations and rover missions have documented the abundant presence of sulphate-rich mineral associations on the surface of Mars. Together with widespread occurrences of silica and frequent enrichments of chlorine and bromine in soils and rocks, the sulphate associations are

Leaching Characteristics of Uranium And Copper from Their Mineralization in the Carbonate Rich latosol of Abu-Thor Locality, South Western Sinai, Egypt

International Nuclear Information System (INIS)

El-Sheikh, E.M.; Ghazala, R.A.; Abdelwarith, A.; Salem, F.; Ali, S.

2015-01-01

The chemical processing of the poly-mineralized carbonate rich latosol ore occurring at Abu-Thor locality of south western Sinai area has been studied for the recovery of uranium and copper metal values. A technological sample assaying 700 ppm U and 9.7% Cu was collected. In the present study, two successive percolation leaching procedures were performed after determination of optimum leaching factors by agitation leaching process. The first was carried out for uranium recovery by using urea as organic leaching agent which was possible to achieve leaching efficiency exceeding 90.3%. This procedure was followed by a second one for copper recovery using ammonium hydroxide solution and ammonium carbonate. The obtained dissolution efficiency was about 93%. The leached metal values namely U and Cu from the studied ore were then extracted as marketable products in the form of ammonium diuranate and copper sulphate, respectively.

X-ray CT Scanning Reveals Long-Term Copper Pollution Effects on Functional Soil Structure

DEFF Research Database (Denmark)

Naveed, Muhammad; Møldrup, Per; Homstrup, Martin

Soil structure plays the main role in the ability of the soil to fulfill essential soil functions such as the root growth, rate of water infiltration and retention, transport of gaseous and chemicals/pollutants through the soil. Soil structure is a dynamic soil property and affected by various...... factors such as soil type, land use, and soil contamination. In this study, we quantified the soil structure using X-ray CT scanning and revealed the effect of a long history of Copper (Cu) pollution on it. A fallow field at Hygum Denmark provides this opportunity as it had a long history of Copper...... sulphate contamination in a gradient with Cu content varies from 21 mg kg-1 to 3837 mg kg-1. Total 20 intact soil columns (diameter of 10 cm and height of 8 cm) were sampled at five locations along the Cu-gradient from a depth of 5 to 15 cm below surface level. The soil columns were scanned at a voxel...

Electroless copper plating on 3-mercaptopropyltriethoxysilane modified PET fabric challenged by ultrasonic washing

International Nuclear Information System (INIS)

Lu Yinxiang

2009-01-01

Electroless deposition of Cu on poly(ethylene terephthalate) (PET) fabric modified with 3-mercaptopropyltriethoxysilane was investigated. Morphology, composition, structure, thermal decomposing behavior of copper coating PET fabric after ultrasonic washing in water for 1 h were characterized by scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analysis, X-ray photoelectron spectroscopy (XPS), Raman spectrometer, X-ray diffraction (XRD), and thermogravimetric analysis (TG), respectively. Copper plating on modified fabric has good adherence stability and high electric conductivity before and after ultrasonic washing, while copper coating fabric without modification is easily destroyed during the washing process, which leads to the textile changing from conductor to dielectric. As the copper weight on the treated fabric is 28 g/m 2 , the shielding effectiveness (SE) is more than 54 dB at frequency ranging from 0.01 MHz to 18 GHz.

Risk minimisation of FGD gypsum leachates by incorporation of aluminium sulphate

Energy Technology Data Exchange (ETDEWEB)

Alvarez-Ayuso, E. [Department of Environmental Geology, Institute of Earth Sciences ' Jaume Almera' (CSIC), C/ Lluis Sole i Sabaris, s/n, 08028 Barcelona (Spain); Department of Environmental Geochemistry, IRNASA, CSIC, Apto. 257, 37071 Salamanca (Spain)], E-mail: ealvarez@ija.csic.es; Querol, X. [Department of Environmental Geology, Institute of Earth Sciences ' Jaume Almera' (CSIC), C/ Lluis Sole i Sabaris, s/n, 08028 Barcelona (Spain); Ballesteros, J.C.; Gimenez, A. [Endesa Generacion, S.A., C/ Ribera de Loira, 60, 28042 Madrid (Spain)

2008-11-15

The incorporation of aluminium sulphate to (flue gas desulphurisation) FGD gypsum before its disposal was investigated as a way to minimise the risk supposed by the high fluoride content of its leachates. Using a bath method the kinetic and equilibrium processes of fluoride removal by aluminium sulphate were studied at fluoride/aluminium molar concentration (F/Al) ratios in the range 1.75 10{sup -2}-1.75 under the pH conditions (about 6.5) of FGD gypsum leachates. It was found that fluoride removal was a very fast process at any of the (F/Al) ratios subject of study, with equilibrium attained within the first 15 min of interaction. High decreases in solution fluoride concentrations (50-80%) were found at the equilibrium state. The use of aluminium sulphate in the stabilization of FGD gypsum proved to greatly decrease its fluoride leachable content (in the range 20-90% for aluminium sulphate doses of 0.1-5%, as determined by the European standard EN 12457-4). Such fluoride leaching minimisation assures the characterization of this by-product as a waste acceptable at landfills for non-hazardous wastes according to the Council Decision 2003/33/EC on waste disposal. Furthermore, as derived from column leaching studies, the proposed stabilization system showed to be highly effective in simulated conditions of disposal, displaying fluoride leaching reduction values about 55 and 80% for aluminium sulphate added amounts of 1 and 2%, respectively.

Abiotic nitrate and sulphate reduction by hydrogen: a comparative experimental study

International Nuclear Information System (INIS)

Truche, L.; Berger, G.; Albrecht, A.; Giffaut, E.

2010-01-01

Document available in extended abstract form only. The bituminous waste which is part of the intermediate level, long-lived waste (MAVL) is characterised, amongst others, by the coexistence of nitrates, sulphates, organic matter, native metals and hydrogen gas in the waste mixture and package. It can be considered as the most complex example that will be used to discuss redox reactions occurring in such waste mixtures. The evaluation of the redox conditions requires quantification of the amount of electron acceptors and donors and definition of the kinetics of redox reaction. The objectives of an experimental study to unravel some of these reaction complexities are: - to investigate nature and rate of sulphate and nitrate reduction by hydrogen in the presence of different catalysts (stainless steel, hastelloy, magnetite and argillite); - to compare sulphate and nitrate as electron acceptors; - to provide a mechanistic model of these reactions. It is well known that reduction of sulphate and nitrate requires high activation energies, usually supplied either by thermal processes or via bacterial and surface catalysis, of which the latter has been investigated in this study. Preliminary experiments performed at 150 deg. C and under H 2 pressure show that sulphate reduction is enhanced in the presence of magnetite, but essentially under the restricted condition of low sulphate concentration and at a pH below the Point of Zero Charge of magnetite. This suggests that sorption of sulphate contributes to the catalysed reaction (at low pH) but provided that the magnetite surface sites are not saturated with respect to aqueous sulphate (low concentration). On the contrary, nitrate reduction is observed whatever the pH and the nitrate concentration in the presence of both magnetite and hastelloy C276 (Ni, Cr, Mo, W, Fe alloy). The effect of temperature on the rate of nitrate reduction (500 ppm KNO 3 solution) is shown by comparing three different experiments conducted in

Grass-cellulose as energy source for biological sulphate removal from acid mine effluents

CSIR Research Space (South Africa)

Greben, HA

2008-11-01

Full Text Available The biological sulphate removal technology requires carbon and energy sources to reduce sulphate to sulphide. Plant biomass, e.g. grass, is a sustainable source of energy when cellulose is utilised during anaerobic degradation, producing volatile...

Development of a glass matrix for vitrification of sulphate bearing high level radioactive liquid waste

International Nuclear Information System (INIS)

Kaushik, C.P.; Mishra, R.K.; Thorat, Vidya; Ramchandran, M.; Amar Kumar; Ozarde, P.D.; Raj, Kanwar; Das, D.

2004-07-01

High level radioactive liquid waste (HLW) is generated during reprocessing of spent nuclear fuel. In the earlier reprocessing flow sheet ferrous sulphamate has been used for valancy adjustment of Pu from IV to III for effective separation. This has resulted in generation of HLW containing significance amount of sulphate. Internationally borosilicate glass matrix has been adopted for vitrification of HLW. The first Indian vitrification facility at Waste Immobilislition Plant (WIP), Tarapur a five component borosilicate matrix (SiO 2 :B 2 O 3 :Na 2 O : MnO : TiO 2 ) has been used for vitrification of waste. However at Trombay HLW contain significant amount of sulphate which is not compatible with standard borosilicate formulation. Extensive R and D efforts were made to develop a glass formulation which can accommodate sulphate and other constituents of HLW e.g., U, Al, Ca, etc. This report deals with development work of a glass formulations for immobilization of sulphate bearing waste. Different glass formulations were studied to evaluate the compatibility with respect to sulphate and other constituents as mentioned above. This includes sodium, lead and barium borosilicate glass matrices. Problems encountered in different glass matrices for containment of sulphate have also been addressed. A glass formulation based on barium borosilicate was found to be effective and compatible for sulphate bearing high level waste. (author)

Thermodynamic evaluation of Cu-H-O-S-P system - Phase stabilities and solubilities for OFP-copper

International Nuclear Information System (INIS)

Magnusson, Hans; Frisk, Karin

2013-04-01

A thermodynamic evaluation for Cu-H-O-S-P has been made, with special focus on the phase stabilities and solubilities for OFP-copper. All binary systems including copper have been reviewed. Gaseous species and stoichiometric crystalline phases have been included for higher systems. Sulphur in OFP-copper will be found in sulphides. The sulphide can take different morphologies but constant stoichiometry Cu 2 S. The solubility of sulphur in FCC-copper reaches ppm levels already at 550 deg C and decreases with lower temperature. No phosphorus-sulphide will be stable, although the copper sulphide can be replaced by copper sulphates at high partial pressure oxygen like in the oxide scale. Phosphorus has a high affinity to oxygen, and phosphorus oxide P 4 O 10 and copper phosphates (Cu 2 P 2 O 7 and Cu 3 (PO 4 ) 2 ) are all more stable than copper oxide Cu 2 O. With hydrogen present at atmospheric pressure, copper phosphates Cu 2 P 2 O 7 and Cu 3 (P 2 O 6 OH) 2 are both more stable than water vapour or aqueous water at temperatures below 400 deg C. At high pressure conditions, the copper phosphates can be reduced giving water. However, the phosphates are still more stable than water vapour. The solubility limit of phosphorus in FCC-copper at 25 deg C is 510 ppm, in equilibrium with copper phosphide Cu 3 P. The major part of phosphorus in OFP-copper will be in solid solution. Oxygen in FCC-copper has a very low solubility. In the presence of a strong oxide forming element such as phosphorus in OFP-copper, the solubility decreases even more. Copper oxides will become stable first when all phosphorus has been consumed, which takes place at twice the phosphorus content, calculated in weight. Hydrogen has a low solubility in copper, calculated as 0.1 ppm at 675 deg C. No crystalline hydrogen phase has been found stable at atmospheric pressures and above 400 deg C. At lower temperatures the hydrogen containing phosphate Cu 3 (P 2 O 6 OH) 2 can become stable. Measured hydrogen

Chaperones CCS, ATOX and COXIV responses to copper supplementation in healthy adults.

Science.gov (United States)

Araya, Magdalena; Andrews, Monica; Pizarro, Fernando; Arredondo, Miguel

2012-04-01

Assessment of proteins in blood and other tissues has failed to identify markers of early copper effects on health. Studies in animal models show that chaperone of SOD (CCS) respond to changes of copper status. Evidence about other copper chaperones (COXIV, ATOX) is not clear. The aim of this study was to assess by means of an in vitro challenge the mRNA relative abundance of ccs, sod1, coxIV, mtIIa and atox in peripheral mononuclear cells (PMNCs) obtained from healthy individuals, acutely and chronically supplemented with small-to-moderate amounts of copper. Healthy participants received 8 mg Cu/d (supplemented group, SG) or placebo, (placebo group, PG) for 2 months. Biochemical indicators were assessed at basal (T0) and after 2 (T2) and 60 days (T60). At these times PMNCs were obtained, challenged with 1, 5 or 20 μM Cu-histidine for 20 h and the mRNA relative abundance of the selected genes assessed by real time PCR. The results showed that at T0, intracellular copper was not different between experimental and control groups. This increased at T2 and T60 when the copper in the media increased (two-way ANOVA, P CCS mRNA transcripts showed no significant changes (two-way ANOVA) at T2 and T60. In SG, CCS changed by treatment, time and interaction (two-way ANOVA, all P CCS but not SOD, ATOX or COXIV responded consistently to controlled changes of copper availability in an in vitro copper challenge.

Static antibiotic spacers augmented by calcium sulphate impregnated beads in revision TKA: Surgical technique and review of literature.

Science.gov (United States)

Risitano, Salvatore; Sabatini, Luigi; Atzori, Francesco; Massè, Alessandro; Indelli, Pier Francesco

2018-06-01

Periprosthetic joint infection (PJI) is a serious complication in total knee arthroplasty (TKA) and represents one of the most common causes of revision. The challenge for surgeons treating an infected TKA is to quickly obtain an infection-free joint in order to re-implant, when possible, a new TKA. Recent literature confirms the role of local antibiotic-loaded beads as a strong bactericidal, allowing higher antibiotic elution when compared with antibiotic loaded spacers only. Unfortunately, classical Polymethylmethacrylate (PMMA) beads might allow bacteria adhesion, secondary development of antibiotic resistance and eventually surgical removal once antibiotics have eluted. This article describes a novel surgical technique using static, custom-made antibiotic loaded spacers augmented by calcium sulphate antibiotic-impregnated beads to improve the success rate of revision TKA in a setting of PJI. The use of calcium sulphate beads has several potential benefits, including a longer sustained local antibiotic release when compared with classical PMMA beads and, being resorbable, not requiring accessory surgical interventions.

Treatment of acid and sulphate-rich effluents in an integrated biological/chemical process

CSIR Research Space (South Africa)

Maree, JP

2004-04-01

Full Text Available .4 g SO4/(l.d). The rate of biological sulphate removal was found to be directly related to the square root of sulphate, COD and VSS concentrations respectively, and inversely proportional to sulphide concentration. The practical value of simultaneous...

Comparison of the effects of the K(+)-channel openers cromakalim and minoxidil sulphate on vascular smooth muscle.

Science.gov (United States)

Wickenden, A. D.; Grimwood, S.; Grant, T. L.; Todd, M. H.

1991-01-01

1 The actions of the potassium channel openers, cromakalim and minoxidil sulphate, were compared in a range of isolated blood vessel preparations. 2 Cromakalim and minoxidil sulphate inhibited spontaneous mechanical activity of the guinea-pig portal vein and relaxed the noradrenaline precontracted rat aorta with similar potency. In contrast, minoxidil sulphate was less potent than cromakalim in inhibiting spontaneous activity in the rat portal vein and was essentially inactive in the noradrenaline precontracted rat mesenteric artery and rabbit aorta. 3 Minoxidil sulphate did not antagonize the effects of cromakalim in the rabbit aorta indicating it was not acting as a partial 'agonist'. 4 Charybdotoxin, noxiustoxin and rubidium failed to discriminate between cromakalim and minoxidil sulphate indicating that the apparently selective effects of minoxidil sulphate were not mediated by either Ca(2+)-activated potassium channels, delayed rectifiers or rubidium impermeable potassium channels. 5 Glibenclamide antagonized the effects of cromakalim in an apparently competitive manner whereas the effects of minoxidil sulphate were antagonized in a non-competitive manner. The involvement of subtypes of ATP-sensitive potassium channels is discussed. PMID:1878752

Differential toxicity and influence of salinity on acute toxicity of ...

African Journals Online (AJOL)

Differential toxicity and influence of salinity on acute toxicity of copper sulphate and lead nitrate against Oreochromis niloticus. KA Bawa-Allah, F Osuala, J Effiong. Abstract. This study investigated the salinity-tolerance of Oreochromis niloticus and the influence of salinity changes on the acute toxicities of copper sulphate ...

Sodium Sulphate Effect on Cement Produced with Building Stone Waste

Directory of Open Access Journals (Sweden)

Emre Sancak

2015-01-01

Full Text Available In this study, the blended cements produced by using the building stone waste were exposed to sulphate solution and the cement properties were examined. Prepared mortar specimens were cured under water for 28 days and then they were exposed to three different proportions of sodium sulphate solution for 125 days. Performances of cements were determined by means of compressive strength and tensile strength tests. The broken parts of some mortar bars were examined with scanning electron microscope (SEM. Besides, they were left under moist atmosphere and their length change was measured and continuously monitored for period of 125 days. In blended cements, solely cements obtained by replacing 10–20% of diatomites gave similar strength values with ordinary Portland cement (CEM I 42.5R at the ages of 7, 28, and 56 days. In all mortar specimens that included either waste andesite (AP or marble powder (MP showed best performance against very severe effective sodium sulphate solutions (13500 mg/L.

Should Magnesium Sulphate Prophylaxis be Used in all Cases of Severe Preeclampsia?

Directory of Open Access Journals (Sweden)

Sohini Bhattacharya,

2011-01-01

Full Text Available A case control study, undertaken in the department of Obstetrics and Gynecology in a tertiary referral centre, was designed to administer standard dose of magnesium sulphate to 50 randomly selected severely preeclamptic women in labor (Group 1. 48 women who formed the control group did not receive the drug (Group 2. The admission – delivery interval, rate of Cesarean section showed no statistically significant difference. Four patients developed convulsions in Group 1 in contrast to twelve patients in Group 2. Efficacy of magnesium sulphate at preventing eclampsia was calculated as 68%. Mild respiratory depression occurred in two cases and oliguria in eight cases in Group 1. Both the conditions improved on suspending further doses of magnesium sulphate. No patient had post partum haemorrhage in Group 1 although 4% patients had it in Group 2. Neonatal outcome was comparable in both the groups. Hence magnesium sulphate may be regarded as a fairly safe and effective prophylactic agent for eclampsia when used in severe preeclampsia in labor.

Thermal decomposition of hydrotalcite with chromate, molybdate or sulphate in the interlayer

Energy Technology Data Exchange (ETDEWEB)

Frost, Ray L. [Inorganic Materials Research Program, School of Physical and Chemical Sciences, Queensland University of Technology, GPO Box 2434, Brisbane Queensland 4001 (Australia)]. E-mail: r.frost@qut.edu.au; Musumeci, Anthony W. [Inorganic Materials Research Program, School of Physical and Chemical Sciences, Queensland University of Technology, GPO Box 2434, Brisbane Queensland 4001 (Australia); Bostrom, Thor [Inorganic Materials Research Program, School of Physical and Chemical Sciences, Queensland University of Technology, GPO Box 2434, Brisbane Queensland 4001 (Australia); Adebajo, Moses O. [Inorganic Materials Research Program, School of Physical and Chemical Sciences, Queensland University of Technology, GPO Box 2434, Brisbane Queensland 4001 (Australia); Weier, Matt L. [Inorganic Materials Research Program, School of Physical and Chemical Sciences, Queensland University of Technology, GPO Box 2434, Brisbane Queensland 4001 (Australia); Martens, Wayde [Inorganic Materials Research Program, School of Physical and Chemical Sciences, Queensland University of Technology, GPO Box 2434, Brisbane Queensland 4001 (Australia)

2005-05-15

The thermal decomposition of hydrotalcites with chromate, molybdate and sulphate in the interlayer has been studied using thermogravimetric analysis coupled to a mass spectrometer measuring the gas evolution. X-ray diffraction shows the hydrotalcites have a d(0 0 3) spacing of 7.98 A with very small differences in the d-spacing between the three hydrotalcites. XRD was also used to determine the products of the thermal decomposition. For the sulphate-hydrotalcite decomposition the products were MgO and a spinel MgAl{sub 2}O{sub 4}, for the chromate interlayered hydrotalcite MgO, Cr{sub 2}O{sub 3} and spinel. For the molybdate interlayered hydrotalcite the products were MgO, spinel and MgMoO{sub 4}. EDX analyses enabled the formula of the hydrotalcites to be determined. Two processes are observed in the thermal decomposition namely dehydration and dehydroxylation and for the case of the sulphate interlayered hydrotalcite, a third process is the loss of sulphate. Both the dehydration and dehydroxylation take place in three steps each for each of the hydrotalcites.

Variations in the Peritrophic Matrix Composition of Heparan Sulphate from the Tsetse Fly, Glossina morsitans morsitans

Directory of Open Access Journals (Sweden)

Evelyn Rogerson

2018-03-01

Full Text Available Tsetse flies are the principal insect vectors of African trypanosomes—sleeping sickness in humans and Nagana in cattle. One of the tsetse fly species, Glossina morsitans morsitans, is host to the parasite, Trypanosoma brucei, a major cause of African trypanosomiasis. Precise details of the life cycle have yet to be established, but the parasite life cycle involves crossing the insect peritrophic matrix (PM. The PM consists of the polysaccharide chitin, several hundred proteins, and both glycosamino- and galactosaminoglycan (GAG polysaccharides. Owing to the technical challenges of detecting small amounts of GAG polysaccharides, their conclusive identification and composition have not been possible until now. Following removal of PMs from the insects and the application of heparinases (bacterial lyase enzymes that are specific for heparan sulphate (HS GAG polysaccharides, dot blots with a HS-specific antibody showed heparan sulphate proteoglycans (HSPGs to be present, consistent with Glossina morsitans morsitans genome analysis, as well as the likely expression of the HSPGs syndecan and perlecan. Exhaustive HS digestion with heparinases, fluorescent labeling of the resulting disaccharides with BODIPY fluorophore, and separation by strong anion exchange chromatography then demonstrated the presence of HS for the first time and provided the disaccharide composition. There were no significant differences in the type of disaccharide species present between genders or between ages (24 vs. 48 h post emergence, although the HS from female flies was more heavily sulphated overall. Significant differences, which may relate to differences in infection between genders or ages, were evident, however, in overall levels of 2-O-sulphation between sexes and, for females, between 24 and 48 h post-emergence, implying a change in expression or activity for the 2-O-sulphotransferase enzyme. The presence of significant quantities of disaccharides containing the

Molecular structure of dextran sulphate sodium in aqueous environment

Science.gov (United States)

Yu, Miao; Every, Hayley A.; Jiskoot, Wim; Witkamp, Geert-Jan; Buijs, Wim

2018-03-01

Here we propose a 3D-molecular structural model for dextran sulphate sodium (DSS) in a neutral aqueous environment based on the results of a molecular modelling study. The DSS structure is dominated by the stereochemistry of the 1,6-linked α-glucose units and the presence of two sulphate groups on each α-glucose unit. The structure of DSS can be best described as a helix with various patterns of di-sulphate substitution on the glucose rings. The presence of a side chain does not alter the 3D-structure of the linear main chain much, but affects the overall spatial dimension of the polymer. The simulated polymers have a diameter similar to or in some cases even larger than model α-hemolysin nano-pores for macromolecule transport in many biological processes, indicating a size-limited translocation through such pores. All results of the molecular modelling study are in line with previously reported experimental data. This study establishes the three-dimensional structure of DSS and summarizes the spatial dimension of the polymer, serving as the basis for a better understanding on the molecular level of DSS-involved electrostatic interaction processes with biological components like proteins and cell pores.

Magnesium sulphate as an anticonvulsant in the management of eclampsia

International Nuclear Information System (INIS)

Ahmed, R.

2004-01-01

Objective: To evaluate the use of magnesium sulphate (MgSO/sub 4/) as an anticonvulsant in the management of eclamptic patients. Patients and Methods: Out of a total of 6050 pregnant women, 31 patients had eclampsia and were managed according to the set protocol. MgSO/sub 4/ 'Nas given to eclamptic patients according to protocol who had no contraindication to this agent. Recurrence of convulsion, side effects of magnesium sulphate, maternal and fetal outcome was noted. Results: Over two years' study period, out of 6050 patients, 31 were admitted with eclampsia (0.51 %). There was no maternal death. Out of 31 eclamptic patients only 5 patients were booked. Twenty-two patients (70.9%) were primigravida and 9 (29%) were multigravida. Seventeen (54%) were less than 20 years of age, 22 (79.9%) patients were admitted with antepartum and 6 (19.35%) had postpartum eclampsia. Magnesium sulphate was effective in 29 (93.54%) patients. Fifteen patients delivered by caesarean (C) section and 16 delivered vaginally. Twenty-nine (93.5%) babies were born alive. Two patients had recurrent convulsion i.e. 6.4%. Only one patient had respiratory depression after the use of magnesium sulphate. Conclusion: Eclampsia was well controlled by the use of MgSO/sub 4/. There were only 2 patients who had recurrence of convulsion. Convulsions were controlled in 29 (93.54%) patients despite lack of monitoring facilities of serum magnesium level. (author)

Predicting the effects of microbial activity on the corrosion of copper nuclear fuel waste disposal containers

International Nuclear Information System (INIS)

King, F.; Stroes-Gascoyne, S.

1996-08-01

Microbially influenced corrosion (MIC) of copper nuclear fuel waste containers may occur in a disposal vault located 500-1000 m underground in the granitic rock of the Canadian Shield. The extent and diversity of microbial activity in the vault is expected to be limited initially because of the aggressive conditions produced by γ-radiation, elevated temperatures and desiccation of the clay-based buffer in which the containers will be embedded. Experimental results on the heat- and radiation-sensitivity of the natural microbiota in buffer material are presented. The data suggest that the low water activity in the buffer material will severely limit the growth of microbes near the container. The most likely form of MIC involves sulphate-reducing bacteria (SRB). Electrochemical experiments using a clay-covered copper electrode have shown that sulphide ions produced by SRB could diffuse through buffer material and induce corrosion of the container. A method to predict the long-term corrosion behaviour is presented. (author)

Correlation analysis between sulphate content and leaching of sulphates in recycled aggregates from construction and demolition wastes.

Science.gov (United States)

Barbudo, Auxi; Galvín, Adela P; Agrela, Francisco; Ayuso, Jesús; Jiménez, Jose Ramón

2012-06-01

In some recycled aggregates applications, such as component of new concrete or roads, the total content of soluble sulphates should be measured and controlled. Restrictions are usually motivated by the resistance or stability of the new structure, and in most cases, structural concerns can be remedied by the use of techniques such as sulphur-resistant cements. However, environmental risk assessment from recycling and reuse construction products is often forgotten. The purpose of this study is to analyse the content of soluble sulphate on eleven recycled aggregates and six samples prepared in laboratory by the addition of different gypsum percentages. As points of reference, two natural aggregates were tested. An analysis of the content of the leachable amount of heavy metals regulated by European regulation was included. As a result, the correlation between solubility and leachability data allow suggest a limiting gypsum amount of 4.4% on recycled aggregates. This limit satisfies EU Landfill Directive criteria, which is currently used as reference by public Spanish Government for recycled aggregates in construction works. Copyright © 2012 Elsevier Ltd. All rights reserved.

Sulphated glycosaminoglycans and proteoglycans in the developing vertebral column of juvenile Atlantic salmon (Salmo salar).

Science.gov (United States)

Hannesson, Kirsten O; Ytteborg, Elisabeth; Takle, Harald; Enersen, Grethe; Bæverfjord, Grete; Pedersen, Mona E

2015-08-01

In the present study, the distribution of sulphated glycosaminoglycans (GAGs) in the developing vertebral column of Atlantic salmon (Salmo salar) at 700, 900, 1100 and 1400 d° was examined by light microscopy. The mineralization pattern was outlined by Alizarin red S and soft structures by Alcian blue. The temporal and spatial distribution patterns of different types of GAGs: chondroitin-4-sulphate/dermatan sulphate, chondroitin-6-sulphate, chondroitin-0-sulphate and keratan sulphate were addressed by immunohistochemistry using monoclonal antibodies against the different GAGs. The specific pattern obtained with the different antibodies suggests a unique role of the different GAG types in pattern formation and mineralization. In addition, the distribution of the different GAG types in normal and malformed vertebral columns from 15 g salmon was compared. A changed expression pattern of GAGs was found in the malformed vertebrae, indicating the involvement of these molecules during the pathogenesis. The molecular size of proteoglycans (PGs) in the vertebrae carrying GAGs was analysed with western blotting, and mRNA transcription of the PGs aggrecan, decorin, biglycan, fibromodulin and lumican by real-time qPCR. Our study reveals the importance of GAGs in development of vertebral column also in Atlantic salmon and indicates that a more comprehensive approach is necessary to completely understand the processes involved.

Sulphation of calcium-based sorbents in circulating fluidised beds under oxy-fuel combustion conditions

Energy Technology Data Exchange (ETDEWEB)

Francisco Garcia-Labiano; Luis F. de Diego; Alberto Abad; Pilar Gayan; Margarita de las Obras-Loscertales; Aranzazu Rufas; Juan Adanez [Instituto de Carboquimica (CSIC), Zaragoza (Spain). Dept. Energy and Environment

2009-07-01

Sulphur Retention (SR) by calcium-based sorbents is a process highly dependent on the temperature and CO{sub 2} concentration. In circulating fluidised beds combustors (CFBC's) operating under oxy-fuel conditions, the sulphation process takes place in atmospheres enriched in CO{sub 2} with bed concentrations that can vary from 40 to 95%. Under so high CO{sub 2} concentrations, very different from that in conventional coal combustion atmosphere with air, the calcination and sulphation behaviour of the sorbent must be defined to optimise the SR process in the combustor. The objective of this work was to determine the SO{sub 2} retention capacity of a Spanish limestone at typical oxy-fuel conditions in CFBC's. Long term duration tests of sulphation (up to 24 h), to simulate the residence time of sorbents in CFBC's, were carried out by thermogravimetric analysis (TGA). Clear behaviour differences were found under calcining and non-calcining conditions. Especially relevant was the result obtained at calcining conditions but close to the thermodynamic temperature given for sorbent calcination. This situation must be avoided in CFBC's because the CO{sub 2} produced inside the particle during calcination can destroy the particles if a non-porous sulphate product layer has been formed around the particle. The effect of the main variables on the sorbent sulphation such as SO{sub 2} concentration, temperature, and particle size were analysed in the long term TGA tests. These data were also used to determine the kinetic parameters for the sulphation under oxy-fuel combustion conditions, which were able to adequately predict the sulphation conversion values in a wide range of operating conditions. 20 refs., 5 figs., 2 tabs.

Spore-forming, Desulfosporosinus-like sulphate-reducing bacteria from a shallow aquifer contaminated with gasoline.

Science.gov (United States)

Robertson, W J; Franzmann, P D; Mee, B J

2000-02-01

Previous studies on the geochemistry of a shallow unconfined aquifer contaminated with hydrocarbons suggested that the degradation of some hydrocarbons was linked to bacterial sulphate reduction. There was attenuation of naphthalene, 1,3,5-trimethylbenzene (TMB), toluene, p-xylene and ethylbenzene in the groundwater with concomitant loss of sulphate. Here, the recovery of eight strains of sulphate-reducing bacteria (SRB) from the contaminated site is reported. All were straight or curved rod-shaped cells which formed endospores. Amplification and sequencing of the 16S rDNA indicated that the strains were all sulphate reducers of the Gram-positive line of descent, and were most closely related to Desulfosporosinus (previously Desulfotomaculum) orientis DSM 8344 (97-98.9% sequence similarity). The strains clustered in three phylogenetic groups based on 16S rRNA sequences. Whole cell fatty acid compositions were similar to those of D. orientis DSM 8344, and were consistent with previous studies of fatty acids in soil and groundwater from the site. Microcosms containing groundwater from this aquifer indicated a role for sulphate reduction in the degradation of [ring-UL-14C]toluene, but not for the degradation of [UL-14C]benzene which could also be degraded by the microcosms. Adding one of the strains that was isolated from the groundwater (strain T2) to sulphate-enriched microcosms increased the rate of toluene degradation four- to 10-fold but had no effect on the rate of benzene degradation. The addition of molybdate, an inhibitor of sulphate reduction, to the groundwater samples decreased the rate of toluene mineralization. There was no evidence to support the mineralization of [UL-14C]benzene, [ring-UL-14C]toluene or unlabelled m-xylene, p-xylene, ethylbenzene, TMB or naphthalene by any of the strains in pure culture. Growth of all the strains was completely inhibited by 100 micromol l-1 TMB.

A contribution to the study of CuSO4.5H2O solubility in aqueous media

International Nuclear Information System (INIS)

Juan, D. de; Meseguer, V. F.; Lozano, L. J.

1999-01-01

Pentahydrate copper sulphate (Blue vitriol) is a copper salt used in mineralogy as activator reagent in concentration methods by flotation for sulphide ores: In this work, crystallization conditions of copper sulphate solutions have been determined as a function of both temperature and sulphuric acidity. The results obtained showed that Cu 2+ concentration in the solution is mainly a direct function of the logarithm of temperature and the sulfuric acid concentration. The influence of Zn 2+ presence in copper sulphate solubility has been also studied at ambient temperature. Results obtained led to a multiple linear regression between Cu 2+ concentration in the solution and sulphuric acid and Zn 2+ concentrations in the medium. Finally, a comparison between the results obtained and data available in the literature is made. (Author) 5 refs

A natural analogue for copper waste canisters: The copper-uranium mineralised concretions in the Permian mudrocks of south Devon, United Kingdom

International Nuclear Information System (INIS)

Milodowski, A.E.; Styles, M.T.; Hards, V.L.

2000-08-01

mineralisation and alteration that can be related to the burial and diagenetic history of the Permian strata. The native copper mineralisation exhibits close temporal association with the formation of uraniferous and vanadiferous concretions (known as 'fish-eyes') in the same rocks. Petrographical relationships indicate that both the copper and the 'fish-eye' concretions formed during burial diagenesis but before the maximum compaction of the host mudstone and siltstone. The regional burial history Wessex Basin, indicates that the maximum compaction of the Permian strata would have been achieved by at least the end of the Lower Jurassic (possibly even in the Triassic). Therefore, the native copper mineralisation is older than 176 Ma. The native copper sheets display a complex sequence of alteration and subsequent mineral growth of minerals on their surfaces. The earliest alteration was to copper oxides - principally cuprite with minor tenorite, indicating a change to more oxidising groundwater conditions. The dissolution of native silver and the growth of fringes of copper arsenides followed this. Nickel arsenides and chalcocite, associated with the precipitation of uranium silicates occurred in the later stages of alteration. This suggests a return to a more reducing pore water environment. Again, petrographical relationships indicate that this alteration and subsequent mineralisation is geologically old (i.e. Lower Jurassic or older). Secondary malachite, intimately intergrown copper sulphate and copper oxides, copper chloride, copper-uranium arsenate and uranium vanadates have formed as late-stage alteration products of the native copper and earlier diagenetic cuprite, chalcocite, copper-nickel arsenide and uranium silicate alteration and mineralisation. This latest stage alteration is most probably attributable to near-surface weathering processes. Although the native copper is affected by corrosion, the study has shown that a significant proportion (30-80% of the original

A natural analogue for copper waste canisters: The copper-uranium mineralised concretions in the Permian mudrocks of south Devon, United Kingdom

Energy Technology Data Exchange (ETDEWEB)

Milodowski, A.E.; Styles, M.T.; Hards, V.L. [Natural Environment Research Council (United Kingdom). British Geological Survey

2000-08-01

mineralisation and alteration that can be related to the burial and diagenetic history of the Permian strata. The native copper mineralisation exhibits close temporal association with the formation of uraniferous and vanadiferous concretions (known as 'fish-eyes') in the same rocks. Petrographical relationships indicate that both the copper and the 'fish-eye' concretions formed during burial diagenesis but before the maximum compaction of the host mudstone and siltstone. The regional burial history Wessex Basin, indicates that the maximum compaction of the Permian strata would have been achieved by at least the end of the Lower Jurassic (possibly even in the Triassic). Therefore, the native copper mineralisation is older than 176 Ma. The native copper sheets display a complex sequence of alteration and subsequent mineral growth of minerals on their surfaces. The earliest alteration was to copper oxides - principally cuprite with minor tenorite, indicating a change to more oxidising groundwater conditions. The dissolution of native silver and the growth of fringes of copper arsenides followed this. Nickel arsenides and chalcocite, associated with the precipitation of uranium silicates occurred in the later stages of alteration. This suggests a return to a more reducing pore water environment. Again, petrographical relationships indicate that this alteration and subsequent mineralisation is geologically old (i.e. Lower Jurassic or older). Secondary malachite, intimately intergrown copper sulphate and copper oxides, copper chloride, copper-uranium arsenate and uranium vanadates have formed as late-stage alteration products of the native copper and earlier diagenetic cuprite, chalcocite, copper-nickel arsenide and uranium silicate alteration and mineralisation. This latest stage alteration is most probably attributable to near-surface weathering processes. Although the native copper is affected by corrosion, the study has shown that a significant proportion (30

Determination of Oversulphated Chondroitin Sulphate and Dermatan Sulphate in unfractionated heparin by (1)H-NMR - Collaborative study for quantification and analytical determination of LoD.

Science.gov (United States)

McEwen, I; Mulloy, B; Hellwig, E; Kozerski, L; Beyer, T; Holzgrabe, U; Wanko, R; Spieser, J-M; Rodomonte, A

2008-12-01

Oversulphated Chondroitin Sulphate (OSCS) and Dermatan Sulphate (DS) in unfractionated heparins can be identified by nuclear magnetic resonance spectrometry (NMR). The limit of detection (LoD) of OSCS is 0.1% relative to the heparin content. This LoD is obtained at a signal-to-noise ratio (S/N) of 2000:1 of the heparin methyl signal. Quantification is best obtained by comparing peak heights of the OSCS and heparin methyl signals. Reproducibility of less than 10% relative standard deviation (RSD) has been obtained. The accuracy of quantification was good.

Studies on calcium, magnesium and sulphate in the Mandovi and Zuari river system (Goa)

Digital Repository Service at National Institute of Oceanography (India)

SenGupta, R.; Naik, S.

-conservative parameters. Sulphate, however behaves in a purely conservative manner and remains in a steady state in the rivers. A'Simple mixture'relationship is applied to calculate the dilution and mixing processes in the rivers using calcium, magnesium and sulphate...

Measured Copper Toxicity to Cnesterodon decemmaculatus (Pisces: Poeciliidae and Predicted by Biotic Ligand Model in Pilcomayo River Water: A Step for a Cross-Fish-Species Extrapolation

Directory of Open Access Journals (Sweden)

María Victoria Casares

2012-01-01

Full Text Available In order to determine copper toxicity (LC50 to a local species (Cnesterodon decemmaculatus in the South American Pilcomayo River water and evaluate a cross-fish-species extrapolation of Biotic Ligand Model, a 96 h acute copper toxicity test was performed. The dissolved copper concentrations tested were 0.05, 0.19, 0.39, 0.61, 0.73, 1.01, and 1.42 mg Cu L-1. The 96 h Cu LC50 calculated was 0.655 mg L-1 (0.823-0.488. 96-h Cu LC50 predicted by BLM for Pimephales promelas was 0.722 mg L-1. Analysis of the inter-seasonal variation of the main water quality parameters indicates that a higher protective effect of calcium, magnesium, sodium, sulphate, and chloride is expected during the dry season. The very high load of total suspended solids in this river might be a key factor in determining copper distribution between solid and solution phases. A cross-fish-species extrapolation of copper BLM is valid within the water quality parameters and experimental conditions of this toxicity test.

Biotreatment of Cr(VI) contaminated waters by sulphate reducing bacteria fed with ethanol

International Nuclear Information System (INIS)

Pagnanelli, F.; Cruz Viggi, C.; Cibati, A.; Uccelletti, D.; Toro, L.; Palleschi, C.

2012-01-01

Highlights: ► Use of ethanol as electron donor for sulphate-reducing bacteria for the treatment of Cr(VI). ► Isolation of contribution in Cr removal (adsorption vs. bioprecipitation). ► Bioassessment of the process effectiveness by ecotoxicological in vivo tests using C. elegans. - Abstract: Biological treatment of Cr(VI) contaminated waters was performed in fixed bed reactors inoculated with SRB (sulphate-reducing bacteria) growing on ethanol. Treatment efficiency was evaluated by checking chemical abatement of Cr(VI) and by ecotoxicological tests using the nematode Caenorhabditis elegans. A preliminary comparison between ethanol and lactate was performed, denoting that using ethanol, the same values of final sulphate abatement were obtained. In addition ethanol showed to be a substrate more competitive than lactate in kinetic terms. Fixed bed column reactors were continuously fed with a solution containing sulphates (3 g L −1 ), ethanol (1.5 g L −1 ) and Cr(VI) (50 mg L −1 ). At steady state the column inoculated with SRB removed 65 ± 5% of sulphate and 95 ± 5% of chromium. Bioactive removal mechanisms predominated over biosorption. Diminution of Cr(VI) toxicity was assessed by using the nematode C. elegans as a test organism showing that the survival of nematodes was 20% in the presence of the untreated influent and raised up to 53% when the nematodes were exposed to the treated effluent.

Formulation and evaluation and terbutaline sulphate and ...

African Journals Online (AJOL)

We report the use of low rugosity lactose, product of controlled crystallization of this carrier, in the formulation of terbutaline sulphate and beclomethasone dipropionate dry powder inhalers. The deposition patterns obtained with inhalation mixtures consisting of the modified lactose and each of the micronised drugs ...

Thermodynamic evaluation of Cu-H-O-S-P system - Phase stabilities and solubilities for OFP-copper

Energy Technology Data Exchange (ETDEWEB)

Magnusson, Hans; Frisk, Karin [Swerea KIMAB, Kista (Sweden)

2013-04-15

A thermodynamic evaluation for Cu-H-O-S-P has been made, with special focus on the phase stabilities and solubilities for OFP-copper. All binary systems including copper have been reviewed. Gaseous species and stoichiometric crystalline phases have been included for higher systems. Sulphur in OFP-copper will be found in sulphides. The sulphide can take different morphologies but constant stoichiometry Cu{sub 2}S. The solubility of sulphur in FCC-copper reaches ppm levels already at 550 deg C and decreases with lower temperature. No phosphorus-sulphide will be stable, although the copper sulphide can be replaced by copper sulphates at high partial pressure oxygen like in the oxide scale. Phosphorus has a high affinity to oxygen, and phosphorus oxide P{sub 4}O{sub 10} and copper phosphates (Cu{sub 2}P{sub 2}O{sub 7} and Cu{sub 3}(PO{sub 4}){sub 2}) are all more stable than copper oxide Cu{sub 2}O. With hydrogen present at atmospheric pressure, copper phosphates Cu{sub 2}P{sub 2}O{sub 7} and Cu{sub 3}(P{sub 2}O{sub 6}OH){sub 2} are both more stable than water vapour or aqueous water at temperatures below 400 deg C. At high pressure conditions, the copper phosphates can be reduced giving water. However, the phosphates are still more stable than water vapour. The solubility limit of phosphorus in FCC-copper at 25 deg C is 510 ppm, in equilibrium with copper phosphide Cu{sub 3}P. The major part of phosphorus in OFP-copper will be in solid solution. Oxygen in FCC-copper has a very low solubility. In the presence of a strong oxide forming element such as phosphorus in OFP-copper, the solubility decreases even more. Copper oxides will become stable first when all phosphorus has been consumed, which takes place at twice the phosphorus content, calculated in weight. Hydrogen has a low solubility in copper, calculated as 0.1 ppm at 675 deg C. No crystalline hydrogen phase has been found stable at atmospheric pressures and above 400 deg C. At lower temperatures the hydrogen

Magnesium sulphate for women at risk of preterm birth for neuroprotection of the fetus

NARCIS (Netherlands)

Doyle, Lex W.; Crowther, Caroline A.; Middleton, Philippa; Marret, Stephane; Rouse, Dwight

2009-01-01

Background Epidemiological and basic science evidence suggests that magnesium sulphate before birth may be neuroprotective for the fetus. Objectives To assess the effects of magnesium sulphate as a neuroprotective agent when given to women considered at risk of preterm birth. Search strategy We

Possible mechanisms for interaction of poly electrolytes with ions in aqueous solution

International Nuclear Information System (INIS)

Siyam, T.

1995-01-01

The interaction between the active groups of water soluble poly electrolytes such as polyacrylamide 'neutral polymers PAM', poly sodium acrylate 'anionic polymer PAANA', polyacrylamide-diallyamine-hydrochloride 'cationic polymer PAM-DAA-HCl and polyacrylamide-diallylethylamine-hydrochloride 'cationic polymer PAM-DAEA-HCl' with copper sulphate has been carried out under different experimental conditions. Spectroscopic studies show that the mechanism of the flock formation due to interaction between the polymer and copper sulphate is a bond formation between the active group of polymeric chains and copper sulphate. This bond formation depends on the nature of polymer chain. It was also found that the amide groups form complexes with hydrated cations, while both carboxylate-and ammonium groups interact by ion-exchange mechanism. The same studies were applied on polyacrylamideacrylic acid resin 'PAM-AA' resin and copper sulphate. The obtained results show that the resin interacts by the same mechanism, where the amide groups form a complex with hydrated cations, while the carboxylic group interacts by ion-exchange mechanism. 1 fig., 1 tab

Automatic colorimetric determination of low concentrations of sulphate for measuring sulphur dioxide in ambient air

Energy Technology Data Exchange (ETDEWEB)

Persson, G A

1966-01-01

An automatic colorimetric method for the determination of low concentrations of sulphate (0-10 microgram/ml) using the thoron indicator is described. Total amounts of sulphate as small as 0.3 micrograms can be determined. The sulphate is precipitated with barium perchlorate and the excess of barium is indicated with 1-(o-arsenophenylazo)-2-naphthol-3-6-disulfonic acid(thoron). The procedure is worked out primarily for the determination of sulphur dioxide in air after absorption in diluted hydrogen peroxide.

Modelling the competition between sulphate reducers and methanogens in a thermophilic methanol-fed bioreactor

NARCIS (Netherlands)

Spanjers, H.; Weijma, J.; Abusam, A.

2002-01-01

Sulphate can be removed from wastewater by means of biological anaerobic reduction to sulphide. The reduction requires the presence of a substrate that can serve as an electron donor. Methanol a suitable electron donor for sulphate reduction under thermophilic conditions. In an anaerobic system

Performance of Electrocoagulation Process for Removal of Sulphate Ion from Aqueous Environments Using Plate Aluminum Electrodes

Directory of Open Access Journals (Sweden)

a.h Mahvi

2012-05-01

Full Text Available

Background and Objectives: Sulphate ion is one of the main ions available in natural and waste water. The high rate of sulphate in drinking water causes health problems such as irritation and digestive problems and makes water taste bitter. The purpose of this study was to assess the efficiency of sulphate ion removal from drinking water through Electrocogualation process (EC using plate aluminum electrodes. Methods: This study was conducted as a pilot plant using one glass tank in the volume of 1.3liter containing 6 plate aluminum electrodes. These electrodes were attached to a power supply in a mono-polar and parallel arrangement in order to switch the alternating current to the direct one. That is, each electrode was attached to positive and negative poles directly and alternately. The tank was filled with synthetic water containing sulphate ion with the concentration of 350 & 700mg/L. Percentage of sulphate ion removal in potential range of 10, 20 and 30 V, reaction times of 40, 20 and 60min and pH 7.0, 3.0 & 11.0 were measured. Results: In this study the maximum efficiency of sulphate ion removal was in the electrical potential of 30 V, reaction time of 60min and pH 11.0. With increase of ion concentration, the time needed to achieve a suitable efficiency of removal increased, that is, it indicated the direct effect of pH and difference of electrical potential on removal of sulphate ion through EC process. Conclusion: The results of this research show that Electrocogualation technology can be introduced as a suitable and promising technique to remove sulphate ion from aqueous environments using plate aluminum electrodes.

Performance of Electrocoagulation Process for Removal of Sulphate Ion from Aqueous Environments Using Plate Aluminum Electrodes

Directory of Open Access Journals (Sweden)

Rajabizadeh A.

2010-09-01

Full Text Available Background and Objectives: Sulphate ion is one of the main ions available in natural and waste water. The high rate of sulphate in drinking water causes health problems such as irritation and digestive problems and makes water taste bitter. The purpose of this study was to assess the efficiency of sulphate ion removal from drinking water through Electrocogualation process (EC using plate aluminum electrodes.Methods: This study was conducted as a pilot plant using one glass tank in the volume of 1.3liter containing 6 plate aluminum electrodes. These electrodes were attached to a power supply in a mono-polar and parallel arrangement in order to switch the alternating current to the direct one. That is, each electrode was attached to positive and negative poles directly and alternately. The tank was filled with synthetic water containing sulphate ion with the concentration of 350 & 700mg/L. Percentage of sulphate ion removal in potential range of 10, 20 and 30 V, reaction times of 40, 20 and 60min and pH 7.0, 3.0 & 11.0 were measured.Results: In this study the maximum efficiency of sulphate ion removal was in the electrical potential of 30 V, reaction time of 60min and pH 11.0. With increase of ion concentration, the time needed to achieve a suitable efficiency of removal increased, that is, it indicated the direct effect of pH and difference of electrical potential on removal of sulphate ion through EC process.Conclusion: The results of this research show that Electrocogualation technology can be introduced as a suitable and promising technique to remove sulphate ion from aqueous environments using plate aluminum electrodes.

Sulphate Potasium Extraction From Banana Stem Ash with Bleaching Earth Waste Liquid

OpenAIRE

Edahwati, Luluk

2010-01-01

Sulphate potassium is one of the important chemistry compound for industrial at our country, usually for fertilizerindustry. Therefore, necessary done sulphate potassium maker watchfulness from various ingredient that containsulphate potassium compound. Among others with extract banana stem ash. Watchfulness methodology that is withmix banana stem ash with aquadest (20 gram ash/1 water litre) in temperature 100oc during 30 minutes and stirringrotation 300 rpm. Ash extract that got reaction wi...

Toxicology studies of primycin-sulphate using a three-dimensional (3D) in vitro human liver aggregate model.

Science.gov (United States)

Pénzes, Ágota; Mahmud Abdelwahab, Elhusseiny Mohamed; Rapp, Judit; Péteri, Zsanett A; Bovári-Biri, Judit; Fekete, Csaba; Miskei, György; Kvell, Krisztián; Pongrácz, Judit E

2017-11-05

Primycin-sulphate is a highly effective compound against Gram (G) positive bacteria. It has a potentially synergistic effect with vancomycin and statins which makes primycin-sulphate a potentially very effective preparation. Primycin-sulphate is currently used exclusively in topical preparations. In vitro animal hepatocyte and neuromuscular junction studies (in mice, rats, snakes, frogs) as well as in in vitro human red blood cell experiments were used to test toxicity. During these studies, the use of primycin-sulphate resulted in reduced cellular membrane integrity and modified ion channel activity. Additionally, parenteral administration of primycin-sulphate to mice, dogs, cats, rabbits and guinea pigs indicated high level of acute toxicity. The objective of this study was to reveal the cytotoxic and gene expression modifying effects of primycin-sulphate in a human system using an in vitro, three dimensional (3D) human hepatic model system. Within the 3D model, primycin-sulphate presented no acute cytotoxicity at concentrations 1μg/ml and below. However, even at low concentrations, primycin-sulphate affected gene expressions by up-regulating inflammatory cytokines (e.g., IL6), chemokines (e.g., CXCL5) and by down-regulating molecules of the lipid metabolism (e.g., peroxisome proliferator receptor (PPAR) alpha, gamma, etc). Down-regulation of PPAR alpha cannot just disrupt lipid production but can also affect cytochrome P450 metabolic enzyme (CYP) 3A4 expression, highlighting the need for extensive drug-drug interaction (DDI) studies before human oral or parenteral preparations can be developed. Copyright © 2017 Elsevier B.V. All rights reserved.

A Cooperative Copper Metal-Organic Framework-Hydrogel System Improves Wound Healing in Diabetes

OpenAIRE

Xiao, Jisheng; Chen, Siyu; Yi, Ji; Zhang, Hao; Ameer, Guillermo A.

2016-01-01

Chronic non-healing wounds remain a major clinical challenge that would benefit from the development of advanced, regenerative dressings that promote wound closure within a clinically relevant time frame. The use of copper ions has shown promise in wound healing applications possibly by promoting angiogenesis. However, reported treatments that use copper ions require multiple applications of copper salts or oxides to the wound bed, exposing the patient to potentially toxic levels of copper io...

Effects of topical corticosteroid and tacrolimus on ceramides and irritancy to sodium lauryl sulphate in healthy skin

DEFF Research Database (Denmark)

Jungersted, Jakob Mutanu; Høgh, Julie Kaae; Hellegren, Lars I

2011-01-01

twice daily for one week with betamethasone, tacrolimus, emollient, or left untreated, respectively. After one week each area was challenged with a 24 h sodium lauryl sulphate patch test. The lipids were collected using the cyanoacrylate method and evaluated by high performance thin layer chromatography......The skin barrier, located in the stratum corneum, is influenced mainly by the lipid and protein composition of this layer. In eczematous diseases impairment of the skin barrier is thought to be of prime importance. Topical anti-inflammatory drugs and emollients are the most widely used eczema...

Effects of Manganese (Ii Sulphate on Structural, Spectral, Optical, Thermal and Mechanical Properties of L-Alanine Sodium Sulphate Single Crystals

Directory of Open Access Journals (Sweden)

F. Praveena

2017-04-01

Full Text Available New Non-linear Optical materials have been attracting in the research world for their potential applications in emerging opto-electronic technology. The dipolar nature of amino acid leads to peculiar physical and chemical properties, thus making a good candidate for NLO applications. Single crystals of manganese(II sulphate doped L-Alanine sodium sulphate(LASS has been synthesized by slow evaporation technique. Structural property of the grown crystals are characterized by X-ray powder diffraction,FT-IR spectral analysis conforms all the functional groups. Thermogravity (TG and differential themogravimetric (DTA analysis have been performed to study the thermal stability of the crystals. The second harmonic generation efficiency was measured by Kurtz-Perry powder technique. The transmission and absorption of electromagnetic radiation is analysed through UV-VIS spectrum. Microhardness was measured at different applied load to understand the mechanical stability of the crystal.

Evaluating portland cement concrete degradation by sulphate exposure through artificial neural networks modeling

International Nuclear Information System (INIS)

Oliveira, Douglas Nunes de; Bourguignon, Lucas Gabriel Garcia; Tolentino, Evandro; Costa, Rodrigo Moyses; Tello, Cledola Cassia Oliveira de

2015-01-01

A concrete is durable if it has accomplished the desired service life in the environment in which it is exposed. The durability of concrete materials can be limited as a result of adverse performance of its cement-paste matrix or aggregate constituents under either chemical or physical attack. Among other aggressive chemical exposures, the sulphate attack is an important concern. Water, soils and gases, which contain sulphate, represent a potential threat to the durability of concrete structures. Sulphate attack in concrete leads to the conversion of the hydration products of cement to ettringite, gypsum, and other phases, and also it leads to the destabilization of the primary strength generating calcium silicate hydrate (C-S-H) gel. The formation of ettringite and gypsum is common in cementitious systems exposed to most types of sulphate solutions. The present work presents the application of the neural networks for estimating deterioration of various concrete mixtures due to exposure to sulphate solutions. A neural networks model was constructed, trained and tested using the available database. In general, artificial neural networks could be successfully used in function approximation problems in order to approach the data generation function. Once data generation function is known, artificial neural network structure is tested using data not presented to the network during training. This paper is intent to provide the technical requirements related to the production of a durable concrete to be used in the structures of the Brazilian near-surface repository of radioactive wastes. (author)

Biotreatment of Cr(VI) contaminated waters by sulphate reducing bacteria fed with ethanol

Energy Technology Data Exchange (ETDEWEB)

Pagnanelli, F., E-mail: francesca.pagnanelli@uniroma1.it [Department of Chemistry, Sapienza University of Rome, P.le Aldo Moro 5, 00185 Rome (Italy); Cruz Viggi, C., E-mail: carolina.cruzviggi@uniroma1.it [Department of Chemistry, Sapienza University of Rome, P.le Aldo Moro 5, 00185 Rome (Italy); Cibati, A., E-mail: alessio.cibati@uniroma1.it [Department of Chemistry, Sapienza University of Rome, P.le Aldo Moro 5, 00185 Rome (Italy); Uccelletti, D., E-mail: daniela.uccelletti@uniroma1.it [Department of Biology and Biotechnology, Sapienza University of Rome, P.le A. Moro 5, 00185 Rome (Italy); Toro, L., E-mail: luigi.toro@uniroma1.it [Department of Chemistry, Sapienza University of Rome, P.le Aldo Moro 5, 00185 Rome (Italy); Palleschi, C., E-mail: claudio.palleschi@uniroma1.it [Department of Biology and Biotechnology, Sapienza University of Rome, P.le A. Moro 5, 00185 Rome (Italy)

2012-01-15

Highlights: Black-Right-Pointing-Pointer Use of ethanol as electron donor for sulphate-reducing bacteria for the treatment of Cr(VI). Black-Right-Pointing-Pointer Isolation of contribution in Cr removal (adsorption vs. bioprecipitation). Black-Right-Pointing-Pointer Bioassessment of the process effectiveness by ecotoxicological in vivo tests using C. elegans. - Abstract: Biological treatment of Cr(VI) contaminated waters was performed in fixed bed reactors inoculated with SRB (sulphate-reducing bacteria) growing on ethanol. Treatment efficiency was evaluated by checking chemical abatement of Cr(VI) and by ecotoxicological tests using the nematode Caenorhabditis elegans. A preliminary comparison between ethanol and lactate was performed, denoting that using ethanol, the same values of final sulphate abatement were obtained. In addition ethanol showed to be a substrate more competitive than lactate in kinetic terms. Fixed bed column reactors were continuously fed with a solution containing sulphates (3 g L{sup -1}), ethanol (1.5 g L{sup -1}) and Cr(VI) (50 mg L{sup -1}). At steady state the column inoculated with SRB removed 65 {+-} 5% of sulphate and 95 {+-} 5% of chromium. Bioactive removal mechanisms predominated over biosorption. Diminution of Cr(VI) toxicity was assessed by using the nematode C. elegans as a test organism showing that the survival of nematodes was 20% in the presence of the untreated influent and raised up to 53% when the nematodes were exposed to the treated effluent.

Evaluating portland cement concrete degradation by sulphate exposure through artificial neural networks modeling

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Douglas Nunes de; Bourguignon, Lucas Gabriel Garcia; Tolentino, Evandro, E-mail: tolentino@timoteo.cefetmg.br [Centro Federal de Educacao Tecnologica de Minas Gerais (CEFET-MG), Timoteo, MG (Brazil); Costa, Rodrigo Moyses, E-mail: rodrigo@moyses.com.br [Universidade de Itauna, Itauna, MG (Brazil); Tello, Cledola Cassia Oliveira de, E-mail: tellocc@cdtn.br [Centro de Desenvolvimento da Tecnologia Nucelar (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2015-07-01

A concrete is durable if it has accomplished the desired service life in the environment in which it is exposed. The durability of concrete materials can be limited as a result of adverse performance of its cement-paste matrix or aggregate constituents under either chemical or physical attack. Among other aggressive chemical exposures, the sulphate attack is an important concern. Water, soils and gases, which contain sulphate, represent a potential threat to the durability of concrete structures. Sulphate attack in concrete leads to the conversion of the hydration products of cement to ettringite, gypsum, and other phases, and also it leads to the destabilization of the primary strength generating calcium silicate hydrate (C-S-H) gel. The formation of ettringite and gypsum is common in cementitious systems exposed to most types of sulphate solutions. The present work presents the application of the neural networks for estimating deterioration of various concrete mixtures due to exposure to sulphate solutions. A neural networks model was constructed, trained and tested using the available database. In general, artificial neural networks could be successfully used in function approximation problems in order to approach the data generation function. Once data generation function is known, artificial neural network structure is tested using data not presented to the network during training. This paper is intent to provide the technical requirements related to the production of a durable concrete to be used in the structures of the Brazilian near-surface repository of radioactive wastes. (author)

Hexagonal ZnO porous plates prepared from microwave synthesized layered zinc hydroxide sulphate via thermal decomposition

Energy Technology Data Exchange (ETDEWEB)

Machovsky, Michal, E-mail: machovsky@ft.utb.cz [Centre of Polymer Systems, University Institute, Tomas Bata University in Zlin, Nad Ovcirnou 3685, 760 01 Zlin (Czech Republic); Polymer Centre, Faculty of Technology, Tomas Bata University in Zlin, Nam. T.G. Masaryka 275, 762 72 Zlin (Czech Republic); Kuritka, Ivo, E-mail: ivo@kuritka.net [Centre of Polymer Systems, University Institute, Tomas Bata University in Zlin, Nad Ovcirnou 3685, 760 01 Zlin (Czech Republic); Polymer Centre, Faculty of Technology, Tomas Bata University in Zlin, Nam. T.G. Masaryka 275, 762 72 Zlin (Czech Republic); Sedlak, Jakub, E-mail: j1sedlak@ft.utb.cz [Centre of Polymer Systems, University Institute, Tomas Bata University in Zlin, Nad Ovcirnou 3685, 760 01 Zlin (Czech Republic); Polymer Centre, Faculty of Technology, Tomas Bata University in Zlin, Nam. T.G. Masaryka 275, 762 72 Zlin (Czech Republic); Pastorek, Miroslav, E-mail: pastorek@ft.utb.cz [Centre of Polymer Systems, University Institute, Tomas Bata University in Zlin, Nad Ovcirnou 3685, 760 01 Zlin (Czech Republic); Department of Polymer Engineering, Faculty of Technology, Tomas Bata University in Zlin, Nam. T.G. Masaryka 275, 762 72 Zlin (Czech Republic)

2013-10-15

Graphical abstract: - Highlights: • Zinc hydroxy sulphate was synthesized in 3 min via microwave hydrothermal route. • Zinc hydroxy sulphate was converted into mesh like porous ZnO by calcining at 900°. • The process of transformation is topotactic. - Abstract: Layered zinc hydroxide sulphate (ZHS) was prepared by microwave-assisted hydrothermal precipitation of zinc sulphate monohydrate with hexamethylenetetramine. Under ambient conditions, the structure of ZHS determined by X-ray diffraction (XRD) was found to be a mixture of zinc hydroxide sulphate pentahydrate Zn{sub 4}SO{sub 4}(OH){sub 6}·5H{sub 2}O and tetrahydrate Zn{sub 4}SO{sub 4}(OH){sub 6}·4H{sub 2}O. Fourier transform infrared (FTIR) spectroscopy was used for characterization of the prepared materials. Based on the interpretation of ZHS's thermal decomposition profile obtained by thermogravimetric analysis, ZnO of high purity was prepared by calcination at 900 °C for 2 h. The structure of the resulting ZnO was confirmed by the XRD. The morphology examination by scanning electron microscopy revealed a porous mesh-like ZnO structure developed from the ZHS precursor at the expense of mass removal due to the release of water and sulphate during the calcination.

Intoxication experiments with beryllium sulphate

International Nuclear Information System (INIS)

Bucurescu, I.; Stan, T.

1990-01-01

The changes in the particular number of animals in two groups of 40 rats each subjected to intoxication experiments with beryllium sulphate was investigated. The two investigations had very different characteristics. In the case of chronic intoxication there was a marked lethality over given time intervals. In the case of subacute intoxication the number of animals decreased with time. It was found empirically that this change can be described by an exponential relationship which lends itself to statistical interpretation. (author)

Effectiveness acidic pre-cleaning for copper-gold ore

Directory of Open Access Journals (Sweden)

Antonio Clareti Pereira

Full Text Available Abstract The presence of copper-bearing minerals is known to bring on many challenges during the cyanidation of gold ore, like high consumption of cyanide and low extraction of metal, which are undesirable impacts on the auriferous recovery in the subsequent process step. The high copper solubility in cyanide prevents the direct use of classical hydrometallurgical processes for the extraction of gold by cyanidation. Additionally, the application of a conventional flotation process to extract copper is further complicated when it is oxidized. As a result, an acid pre-leaching process was applied in order to clean the ore of these copper minerals that are cyanide consumers. The objective was to evaluate the amount of soluble copper in cyanide before and after acidic cleaning. From a gold ore containing copper, the study selected four samples containing 0.22%, 0.55%, 1.00% and 1.36% of copper. For direct cyanidation of the ore without pre-treatment, copper extraction by cyanide complexing ranged from 8 to 83%. In contrast, the pre-treatment carried out with sulfuric acid extracted 24% to 99% of initial copper and subsequent cyanidation extracted 0.13 to 1.54% of initial copper. The study also showed that the copper contained in the secondary minerals is more easily extracted by cyanide (83%, being followed by the copper oxy-hydroxide minerals (60%, while the copper contained in the manganese oxide is less complexed by cyanide (8% a 12%. It was possible to observe that minerals with low acid solubility also have low solubility in cyanide. Cyanide consumption decreased by about 2.5 times and gold recovery increased to above 94% after acidic pre-cleaning.

Comparison of methods for the determination of reduced inorganic sulphur in acid sulphate soils

International Nuclear Information System (INIS)

Santomartino, S.L.

1999-01-01

Full text: The management of acid sulphate soils requires analytical methods that provide accurate data on the quantity of reduced inorganic sulphur within a soil, as it is this fraction that produces acid upon oxidation. This study uses sulphidic Coode Island Silt samples to compare common analytical methods including POCAS (Peroxide Oxidation-Combined Acidity and Sulphate) which consists of TSA (Total Sulphidic Acidity), S pos (Peroxide Oxidisable Sulphur), TOS (Total Oxidisable Sulphur) and chromium-reducible sulphur. The determination of total sulphur by Leco sulphur is strongly correlated with, but slightly less than, that analysed by XRF. Comparison of soil sulphide content by chromium-reducible sulphur, TSA and TOS methods indicates that TOS values are substantially higher than both other methods. The problem with the TOS method lies in the sulphate extraction procedure. Hot distilled water and HCI are commonly used as extractants, however hot distilled water fails to remove organic sulphur, thereby overestimating the sulphide content of the soil. Leco carbon analyses verify that a substantial proportion of organic matter exists within the samples. The HCI extraction process, which uses Ion Chromatography to analyse for sulphate, produces highly inaccurate results due to the interference of the sulphate peak by the chloride peak during analysis. An alternative method involving HCI extraction and XRF analysis of the soil residue is currently being undertaken. The use of KCI to extract sulphate generally produces values similar to the hot distilled water method. The sulphidic content measured by TSA is strongly correlated with, but slightly higher than that determined by the chromium-reducible sulphur method. This is attributed to the use of hydrogen peroxide in the TSA method, which oxidises organic matter to organic acids in addition to oxidising sulphides. These preliminary findings indicate that the chromium-reducible sulphur method is the most suitable

Mitigation of organically bound sulphate from water treatment plants at Bruce NGS and impact on steam generator secondary side chemistry control

Energy Technology Data Exchange (ETDEWEB)

Nashiem, R.; Davloor, R.; Harper, B.; Smith, K. [Bruce Power, Tiverton, Ontario (Canada); Gauthier, C. [CTGIX Services Inc., Burlington, Ontario (Canada); Schexnailder, S. [GE Water and Process Technologies, Dallas, Texas (United States)

2010-07-01

Bruce Power is the source of more than 20 per cent of Ontario's electricity and currently operates six reactor units at the Bruce Nuclear Generating Station A (two units) and B (four units) stations located on Lake Huron. This paper discusses the challenges faced and operating experience (OPEX) gained in meeting WANO 1.0 chemistry performance objectives for steam generator secondary side chemistry control, particularly with control of steam generator sulphates. A detailed sampling and analysis program conducted as part of this study concluded that a major contributor to steam generator (SG) elevated sulphates is Organically Bound Sulphate (OBS) in Water Treatment Plants (WTP) effluent. The Bruce A and B WTPs consist of clarification with downstream sand and carbon filtration for Lake Water pre-treatment, which are followed by conventional Ion Exchange (IX) demineralization. Samples taken from various locations in the process stream were analyzed for a variety of parameters including both organic bound and inorganic forms of sulphate. The results are inconclusive with respect to finding the definitive source of OBS. This is primarily due to the condition that the OBS in the samples, which are in relatively low levels, are masked during chemical analysis by the considerably higher inorganic sulphate background. Additionally, it was also determined that on-line Total Organic Carbon (TOC) levels at different WTP locations did not always correlate well with OBS levels in the effluent, such that TOC could not be effectively used as a control parameter to improve OBS performance of the WTP operation. Improvement efforts at both plants focused on a number of areas including optimization of clarifier operation, replacement of IX resins, addition of downstream mobile polishing trailers, testing of new resins and adsorbents, pilot-scale testing with a Reverse Osmosis (RO) rig, review of resin regeneration and backwashing practices, and operating procedure improvements

Mitigation of organically bound sulphate from water treatment plants at Bruce NGS and impact on steam generator secondary side chemistry control

International Nuclear Information System (INIS)

Nashiem, R.; Davloor, R.; Harper, B.; Smith, K.; Gauthier, C.; Schexnailder, S.

2010-01-01

Bruce Power is the source of more than 20 per cent of Ontario's electricity and currently operates six reactor units at the Bruce Nuclear Generating Station A (two units) and B (four units) stations located on Lake Huron. This paper discusses the challenges faced and operating experience (OPEX) gained in meeting WANO 1.0 chemistry performance objectives for steam generator secondary side chemistry control, particularly with control of steam generator sulphates. A detailed sampling and analysis program conducted as part of this study concluded that a major contributor to steam generator (SG) elevated sulphates is Organically Bound Sulphate (OBS) in Water Treatment Plants (WTP) effluent. The Bruce A and B WTPs consist of clarification with downstream sand and carbon filtration for Lake Water pre-treatment, which are followed by conventional Ion Exchange (IX) demineralization. Samples taken from various locations in the process stream were analyzed for a variety of parameters including both organic bound and inorganic forms of sulphate. The results are inconclusive with respect to finding the definitive source of OBS. This is primarily due to the condition that the OBS in the samples, which are in relatively low levels, are masked during chemical analysis by the considerably higher inorganic sulphate background. Additionally, it was also determined that on-line Total Organic Carbon (TOC) levels at different WTP locations did not always correlate well with OBS levels in the effluent, such that TOC could not be effectively used as a control parameter to improve OBS performance of the WTP operation. Improvement efforts at both plants focused on a number of areas including optimization of clarifier operation, replacement of IX resins, addition of downstream mobile polishing trailers, testing of new resins and adsorbents, pilot-scale testing with a Reverse Osmosis (RO) rig, review of resin regeneration and backwashing practices, and operating procedure improvements

Determinants of magnesium sulphate use in women hospitalized at <29 weeks with severe or non-severe pre-eclampsia.

Directory of Open Access Journals (Sweden)

Dane A De Silva

Full Text Available Magnesium sulphate is recommended by international guidelines to prevent eclampsia among women with pre-eclampsia, especially when it is severe, but fewer than 70% of such women receive magnesium sulphate. We aimed to identify variables that prompt Canadian physicians to administer magnesium sulphate to women with pre-eclampsia.Data were used from the Canadian Perinatal Network (2005-11 of women hospitalized at <29 weeks' who were thought to be at high risk of delivery due to pre-eclampsia (using broad Canadian definition. Unadjusted analyses of relative risks were estimated directly and population attributable risk percent (PAR% calculated to identify variables associated with magnesium sulphate use. A multivariable model was created and a generalized estimating equation was used to estimate the adjusted RR that explained magnesium sulphate use in pre-eclampsia. The adjusted PAR% was estimated by bootstrapping.Of 631 women with pre-eclampsia, 174 (30.1% had severe pre-eclampsia, of whom 131 (75.3% received magnesium sulphate. 457 (69.9% women had non-severe pre-eclamspia, of whom 291 (63.7% received magnesium sulphate. Use of magnesium sulphate among women with pre-eclampsia could be attributed to the following clinical factors (PAR%: delivery for 'adverse conditions' (48.7%, severe hypertension (21.9%, receipt of antenatal corticosteroids (20.0%, maternal transport prior to delivery (9.9%, heavy proteinuria (7.8%, and interventionist care (3.4%.Clinicians are more likely to administer magnesium sulphate for eclampsia prophylaxis in the presence of more severe maternal clinical features, in addition to concomitant antenatal corticosteroid administration, and shorter admission to delivery periods related to transport from another institution or plans for interventionist care.

Green chemical incorporation of sulphate into polyoxoanions of ...

Indian Academy of Sciences (India)

Green chemical incorporation of sulphate into polyoxoanions of molybdenum to nano level ... Keywords. Polyoxometalate; green synthesis; nanostructures; surfactant. ... The effects of reaction parameters such as concentration of surfactant, temperature and pH of solution on the synthesis of nanospheres were investigated.

Analgesic effect of intra-articular magnesium sulphate compared with bupivacaine after knee arthroscopic menisectomy

Directory of Open Access Journals (Sweden)

Yasser A. Radwan

2013-07-01

Full Text Available This work aimed to evaluate the analgesic efficacy of intra-articular injection of magnesium sulphate (4% compared with equivalent volume of bupivacaine (0.5% after outpatient knee arthroscopic meniscectomy. Forty patients were randomly assigned to two groups. Group M (n = 20 received intra-articular magnesium sulphate 4%, group B (n = 20 received bupivacaine (0.5%. Analgesic effect was evaluated by analgesic duration, and by measuring pain intensity at 1, 2, 4, 6, 12, 24 h both at rest and on knee movement to 90°. The primary outcome variable was pain intensity on the VAS at 1, 2, 4, 6, 12, 24 h post arthroscopy at rest and on movement (flexion of knee to 90°, although the magnesium group had lower time weighted averages (TWAs at rest and on movement, these TWAs were not statistically significant. The median duration of postoperative analgesia was significantly longer in the patients treated with magnesium sulphate (528 min than in the bupivacaine group (317 min (p < 0.0001, with less number of patients needing supplementary analgesia in magnesium group (8/20 than those of the bupivacaine group (16/20 (p < 0.022. Also analgesic consumption was significantly lower in the magnesium sulphate group (p < 0.002. We concluded that the use of magnesium sulphate is rational and effective in reducing pain, and is more physiological and shortens convalescence after outpatient arthroscopic meniscectomy, however our hypotheses that analgesic efficacy of intra-articular isotonic magnesium sulphate would be superior to intra-articular local anaesthetic cannot be supported with this study.

Remediation of copper in vineyards – A mini review

International Nuclear Information System (INIS)

Mackie, K.A.; Müller, T.; Kandeler, E.

2012-01-01

Viticulturists use copper fungicide to combat Downy Mildew. Copper, a non-degradable heavy metal, can accumulate in soil or leach into water sources. Its accumulation in topsoil has impacted micro and macro organisms, spurring scientists to research in situ copper removal methods. Recent publications suggest that microorganism assisted phytoextraction, using plants and bacteria to actively extract copper, is most promising. As vineyards represent moderately polluted sites this technique has great potential. Active plant extraction and chelate assisted remediation extract too little copper or risk leaching, respectively. However, despite interesting pot experiment results using microorganism assisted phytoextraction, it remains a challenge to find plants that primarily accumulate copper in their shoots, a necessity in vineyards where whole plant removal would be time consuming and financially cumbersome. Vineyard remediation requires a holistic approach including sustainable soil management, proper plant selection, increasing biodiversity and microorganisms. - Highlights: ► We describe copper distribution and availability in vineyards. ► We explain the environmental impact of copper on organisms, plants and processes. ► We detail possible remediation methods within vineyards. ► Microbially assisted phytoremediation is the most promising remediation method. ► A solution requires an interdisciplinary approach between plants, soil and vines. - This review is significant because it highlights prospective remediation methods usable in copper contaminated vineyards.

Sulphate partitioning into calcite: Experimental verification of pH control and application to seasonality in speleothems

Science.gov (United States)

Wynn, Peter M.; Fairchild, Ian J.; Borsato, Andrea; Spötl, Christoph; Hartland, Adam; Baker, Andy; Frisia, Silvia; Baldini, James U. L.

2018-04-01

Carbonate-associated sulphate (CAS) is a useful carrier of palaeoenvironmental information throughout the geologic record, particularly through its stable isotope composition. However, a paucity of experimental data restricts quantitative understanding of sulphate incorporation into carbonates, and consequently CAS concentrations and their diagenetic modifications are rarely interpreted. However, in the case of calcite speleothems, the remarkably high-resolution CAS records which are obtainable via modern microanalytical techniques represent a potentially invaluable source of palaeoenvironmental information. Here, we describe the results of controlled experiments of sulphate co-precipitation with calcite in freshwater solutions where pH, saturation state, and sulphate concentration were varied independently of each other. Solution pH is confirmed as the principal control on sulphate incorporation into calcite. The relative efficiency of incorporation was calculated as a partition coefficient DSO4 = (mSO4/mCO3)solid/(mSO4/mCO3)solution. High crystal growth rates (driven by either pH or saturation state) encouraged higher values of DSO4 because of an increasing concentration of defect sites on crystal surfaces. At low growth rates, DSO4 was reduced due to an inferred competition between sulphate and bicarbonate at the calcite surface. These experimental results are applied to understand the incorporation of sulphate into speleothem calcite. The experimentally determined pH-dependence suggests that strong seasonal variations in cave air PCO2 could account for annual cycles in sulphate concentration observed in stalagmites. Our new experimentally determined values of DSO4 were compared with DSO4 values calculated from speleothem-drip water monitoring from two caves within the Austrian and Italian Alps. At Obir cave, Austria, DSO4 (×105) varies between 11.1 (winter) and 9.0 (summer) and the corresponding figures for Ernesto cave, Italy, are 15.4 (winter) and 14

Micrometeorological measurement of the dry deposition flux of sulphate and nitrate aerosols to coniferous forest

NARCIS (Netherlands)

Wyers, G.P.; Duyzer, J.H.

1997-01-01

Dry deposition fluxes of sulphate and nitrate have been determined over a coniferous canopy using the aerodynamic gradient technique. Vertical concentration gradients of sulphate and nitrate were measured with filters; the gradient of ammonium bisulphate was measured with thermodenuders. Filter

The soil sulphate effect and maize plant (Zea mays L.) growth of sulphate reducing bacteria (SRB) inoculation in acid sulfate soils with the different soil water condition

Science.gov (United States)

Asmarlaili, S.; Rauf, A.; Hanafiah, D. S.; Sudarno, Y.; Abdi, P.

2018-02-01

The objective of the study was to determine the potential application of sulphate reducing bacteria on acid sulfate soil with different water content in the green house. The research was carried out in the Laboratory and Green House, Faculty of Agriculture, Universitas Sumatera Utara. This research used Randomized Block Design with two treatments factors, ie sulphate reducing bacteria (SRB) isolate (control, LK4, LK6, TSM4, TSM3, AP4, AP3, LK4 + TSM3, LK4 + AP4, LK4 + AP3, LK6 + TSM3, LK6 + AP4, LK6 + AP3, TSM4 + TSM3, TSM4 + AP4, TSM4 + AP3) and water condition (100% field capacity and 110% field capacity). The results showed that application of isolate LK4 + AP4 with water condition 110% field capacity decreased the soil sulphate content (27.38 ppm) significantly after 6 weeks. Application of isolate LK4 + AP3 with water condition 110% field capacity increased soil pH (5.58) after-week efficacy 6. Application of isolate LK4 with water condition 110% field capacity increased plant growth (140 cm; 25.74 g) significantly after week 6. The best treatment was application isolate LK4 with water condition 110% field Capacity (SRB population 2.5x108; soil sulphate content 29.10ppm; soil acidity 4.78; plant height 140cm; plant weight 25.74g).

Effect of temperature on sulphate reduction, growth rate and growth yield in five psychrophilic sulphate-reducing bacteria from Arctic sediments

DEFF Research Database (Denmark)

Knoblauch, C.; Jørgensen, BB

1999-01-01

and T(opt). For strains LSv21 and LSv514, however, growth yields were highest at the lowest temperatures, around 0 degrees C. The results indicate that psychrophilic sulphate-reducing bacteria are specially adapted to permanently low temperatures by high relative growth rates and high growth yields......Five psychrophilic sulphate-reducing bacteria (strains ASv26, LSv21, PSv29, LSv54 and LSv514) isolated from Arctic sediments were examined for their adaptation to permanently low temperatures, All strains grew at -1.8 degrees C, the freezing point of sea water, but their optimum temperature...... for growth (T(opt)) were 7 degrees C (PSv29), 10 degrees C (ASv26, LSv54) and 18 degrees C (LSv21, LSv514), Although T(opt) was considerably above the in situ temperatures of their habitats (-1.7 degrees C and 2.6 degrees C), relative growth rates were still high at 0 degrees C, accounting for 25...

Removal of Pb (II from Aqueous Solutions Using Mixtures of Bamboo Biochar and Calcium Sulphate, and Hydroxyapatite and Calcium Sulphate

Directory of Open Access Journals (Sweden)

Ahmed Hassan

2016-01-01

Full Text Available Sorption characteristics of Pb(II from aqueous solutions through a low-cost adsorbent mixture comprising of Bamboo biochar (BB and Calcium Sulphate (CS, and a more expensive mixture of Hydroxyapatite (HAP and Calcium Sulphate (CS, were investigated. The effects of equilibrium contact time, and adsorbate concentration conducted in batch experiments were studied. Adsorption equilibrium was established in 40 (min. The adsorption mechanism of Pb(II from these two adsorbent mixtures was carried out through a kinetic rate order. A pseudo second-order kinetic model was applied for the adsorption processes. The model yielded good correlation (R2 >0.999 of the experimental data. Adsorption of Pb(II using (BB&CS and (HAP&CS correlated well (R2 >0.99 with both the Langmuir and Freundlich isotherm equations under the concentration range studied. Hence, the effectiveness of an inexpensive natural material (BB&CS mixture in Pb(II removal is established, and is promising for use in other heavy metal adsorptions.

Mechanism of protection of adenosine from sulphate radical anion ...

Indian Academy of Sciences (India)

Unknown

Keywords. Repair by caffeic acid; repair of adenosine radicals; oxidation by sulphate radical anions. ... known that hydroxycinnamic acids are natural anti- oxidants ... acid. 2. Experimental ..... ously and independently under kinetic conditions at.

Preliminary Data on the In Vitro Effect of Copper-Based Compounds on Aerobic Bacterial Microflora Isolated from Sheep Footrot

Directory of Open Access Journals (Sweden)

Flore CHIRILĂ

2018-05-01

The results demonstrated that 7 of the samples (58.33 % are sensitive to the product I, 6 samples (50% to the product III, 4 samples (33.33 % to the product 2 and the 0.5% Copper sulphate solution only has a bacteriostatic effect. In comparison to the two antibiotics, 9 samples (75 % are sensitive to enrofloxacin and only 5 samples (41.66 % to oxytetracycline. Regarding the associations of microorganisms in the samples with resistance, we have found that these are represented by the most common germs of genus Bacillus, Corynebacterium and Gram negative bacteria, and rarer associations with Micrococcus and Staphylococcus.

Susceptibility of salmonid fish to poisons under estuarine conditions. I. Zinc sulphate

Energy Technology Data Exchange (ETDEWEB)

Herbert, D W.M.; Wakeford, A C

1964-01-01

The resistance of yearling rainbow trout and Atlantic salmon smolts to zinc sulphate increases with salinity up to 30-40 percent sea water, in which these species can withstand for 2 days respectively 15 and 13 times as much zinc sulphate as on fresh water. Further increase in salinity to 72 percent sea water reduces tolerance for the zinc salt. Salmon smolts were more susceptible to zinc poisoning than trout in fresh water and at all salinities tested.

Decolourisation and degradation of textile dyes using a sulphate ...

African Journals Online (AJOL)

SERVER

2008-01-18

Jan 18, 2008 ... Full Length Research Paper ... and microflora that augmented a sulphate reducing bacteria (SRB) consortium. ... and degradation of aromatic compounds from the deco- ... ed that aromatic amines are toxic, carcinogenic and.

Glycosaminoglycan sulphation affects the seeded misfolding of a mutant prion protein.

Directory of Open Access Journals (Sweden)

Victoria A Lawson

Full Text Available BACKGROUND: The accumulation of protease resistant conformers of the prion protein (PrP(res is a key pathological feature of prion diseases. Polyanions, including RNA and glycosaminoglycans have been identified as factors that contribute to the propagation, transmission and pathogenesis of prion disease. Recent studies have suggested that the contribution of these cofactors to prion propagation may be species specific. METHODOLOGY/PRINCIPAL FINDING: In this study a cell-free assay was used to investigate the molecular basis of polyanion stimulated PrP(res formation using brain tissue or cell line derived murine PrP. Enzymatic depletion of endogenous nucleic acids or heparan sulphate (HS from the PrP(C substrate was found to specifically prevent PrP(res formation seeded by mouse derived PrP(Sc. Modification of the negative charge afforded by the sulphation of glycosaminoglycans increased the ability of a familial PrP mutant to act as a substrate for PrP(res formation, while having no effect on PrP(res formed by wildtype PrP. This difference may be due to the observed differences in the binding of wild type and mutant PrP for glycosaminoglycans. CONCLUSIONS/SIGNIFICANCE: Cofactor requirements for PrP(res formation are host species and prion strain specific and affected by disease associated mutations of the prion protein. This may explain both species and strain dependent propagation characteristics and provide insights into the underlying mechanisms of familial prion disease. It further highlights the challenge of designing effective therapeutics against a disease which effects a range of mammalian species, caused by range of aetiologies and prion strains.

A novel anti-influenza copper oxide containing respiratory face mask.

Science.gov (United States)

Borkow, Gadi; Zhou, Steve S; Page, Tom; Gabbay, Jeffrey

2010-06-25

Protective respiratory face masks protect the nose and mouth of the wearer from vapor drops carrying viruses or other infectious pathogens. However, incorrect use and disposal may actually increase the risk of pathogen transmission, rather than reduce it, especially when masks are used by non-professionals such as the lay public. Copper oxide displays potent antiviral properties. A platform technology has been developed that permanently introduces copper oxide into polymeric materials, conferring them with potent biocidal properties. We demonstrate that impregnation of copper oxide into respiratory protective face masks endows them with potent biocidal properties in addition to their inherent filtration properties. Both control and copper oxide impregnated masks filtered above 99.85% of aerosolized viruses when challenged with 5.66+/-0.51 and 6.17+/-0.37 log(10)TCID(50) of human influenza A virus (H1N1) and avian influenza virus (H9N2), respectively, under simulated breathing conditions (28.3 L/min). Importantly, no infectious human influenza A viral titers were recovered from the copper oxide containing masks within 30 minutes (masks. Similarly, the infectious avian influenza titers recovered from the copper oxide containing masks were masks 5.03+/-0.54 log(10)TCID(50). The copper oxide containing masks successfully passed Bacterial Filtration Efficacy, Differential Pressure, Latex Particle Challenge, and Resistance to Penetration by Synthetic Blood tests designed to test the filtration properties of face masks in accordance with the European EN 14683:2005 and NIOSH N95 standards. Impregnation of copper oxide into respiratory protective face masks endows them with potent anti-influenza biocidal properties without altering their physical barrier properties. The use of biocidal masks may significantly reduce the risk of hand or environmental contamination, and thereby subsequent infection, due to improper handling and disposal of the masks.

Photochemical Copper Coating on 3D Printed Thermoplastics

Science.gov (United States)

Yung, Winco K. C.; Sun, Bo; Huang, Junfeng; Jin, Yingdi; Meng, Zhengong; Choy, Hang Shan; Cai, Zhixiang; Li, Guijun; Ho, Cheuk Lam; Yang, Jinlong; Wong, Wai Yeung

2016-08-01

3D printing using thermoplastics has become very popular in recent years, however, it is challenging to provide a metal coating on 3D objects without using specialized and expensive tools. Herein, a novel acrylic paint containing malachite for coating on 3D printed objects is introduced, which can be transformed to copper via one-step laser treatment. The malachite containing pigment can be used as a commercial acrylic paint, which can be brushed onto 3D printed objects. The material properties and photochemical transformation processes have been comprehensively studied. The underlying physics of the photochemical synthesis of copper was characterized using density functional theory calculations. After laser treatment, the surface coating of the 3D printed objects was transformed to copper, which was experimentally characterized by XRD. 3D printed prototypes, including model of the Statue of Liberty covered with a copper surface coating and a robotic hand with copper interconnections, are demonstrated using this painting method. This composite material can provide a novel solution for coating metals on 3D printed objects. The photochemical reduction analysis indicates that the copper rust in malachite form can be remotely and photo-chemically reduced to pure copper with sufficient photon energy.

Growth morphology of zinc tris(thiourea) sulphate crystals

Indian Academy of Sciences (India)

The growth morphology of crystals of zinc tris(thiourea) sulphate (ZTS) is investigated experimentally, and computed using the Hartman–Perdok approach. Attachment energies of the observed habit faces are calculated for determining their relative morphological importance. A computer code is developed for carrying out ...

Anodically generated manganese(III) sulphate for the oxidation of ...

Indian Academy of Sciences (India)

Unknown

oxidation of dipeptides in aqueous sulphuric acid medium: A kinetic study ... acetic acid (TFA) and N-methylmorpholine (NMM) were purchased ... and chloroform–methanol– acetic acid .... tion), manganese(II) sulphate and water (to keep the.

Mechanistic studies of copper(I)-catalyzed 1,3-halogen migration.

Science.gov (United States)

Van Hoveln, Ryan; Hudson, Brandi M; Wedler, Henry B; Bates, Desiree M; Le Gros, Gabriel; Tantillo, Dean J; Schomaker, Jennifer M

2015-04-29

An ongoing challenge in modern catalysis is to identify and understand new modes of reactivity promoted by earth-abundant and inexpensive first-row transition metals. Herein, we report a mechanistic study of an unusual copper(I)-catalyzed 1,3-migration of 2-bromostyrenes that reincorporates the bromine activating group into the final product with concomitant borylation of the aryl halide bond. A combination of experimental and computational studies indicated this reaction does not involve any oxidation state changes at copper; rather, migration occurs through a series of formal sigmatropic shifts. Insight provided from these studies will be used to expand the utility of aryl copper species in synthesis and develop new ligands for enantioselective copper-catalyzed halogenation.

A kinetic approach of sulphur behaviour in borosilicate glasses and melts: implications for sulphate incorporation in nuclear waste glasses

Energy Technology Data Exchange (ETDEWEB)

Lenoir, Marion [Service de Confinement des Dechets et Vitrification - Laboratoire d' Etudes de Base sur les Verres, CEA Valrho, Centre de Marcoule, 30207 Bagnols sur Ceze (France); Physique des Mineraux et des Magmas, UMR 7047 - CNRS, Institut de Physique du Globe de Paris, 7 place Jussieu, 75252 Paris Cedex 05 (France); Grandjean, Agnes [Service de Confinement des Dechets et Vitrification - Laboratoire d' Etudes de Base sur les Verres, CEA Valrho, Centre de Marcoule, 30207 Bagnols sur Ceze (France); Neuville, Daniel R. [Physique des Mineraux et des Magmas, UMR 7047 - CNRS, Institut de Physique du Globe de Paris, 7 place Jussieu, 75252 Paris Cedex 05 (France)

2008-07-01

The kinetics of sulphate decomposition in a borosilicate melt were studied using in situ Raman spectroscopy. This technique permits the quantification of the amount of sulphate dissolved in a borosilicate glass as a function of heating time by comparison with measurements obtained by microprobe WDS (Wavelength Dispersive Spectrometry). In order to quantify the content of sulphate obtained by Raman spectroscopy, the integrated intensity of the sulphate band at 985 cm{sup -1} was scaled to the sum of the integrated bands between 800 and 1200 cm{sup -1}, bands that are assigned to Q{sup n} silica units on the basis of previous literature. Viscosities of some borosilicate glasses are also presented here in order to study the kinetics of sulphate decomposition as a function of the viscosity of the melt. This underlines the importance of variations in viscosity depending on the composition of the melt and thus shows that viscosity is an important parameter governing the kinetics of decomposition of sulphate in borosilicate glasses. (authors)

Copper and Copper Proteins in Parkinson's Disease

Science.gov (United States)

Rivera-Mancia, Susana; Diaz-Ruiz, Araceli; Tristan-Lopez, Luis; Rios, Camilo

2014-01-01

Copper is a transition metal that has been linked to pathological and beneficial effects in neurodegenerative diseases. In Parkinson's disease, free copper is related to increased oxidative stress, alpha-synuclein oligomerization, and Lewy body formation. Decreased copper along with increased iron has been found in substantia nigra and caudate nucleus of Parkinson's disease patients. Copper influences iron content in the brain through ferroxidase ceruloplasmin activity; therefore decreased protein-bound copper in brain may enhance iron accumulation and the associated oxidative stress. The function of other copper-binding proteins such as Cu/Zn-SOD and metallothioneins is also beneficial to prevent neurodegeneration. Copper may regulate neurotransmission since it is released after neuronal stimulus and the metal is able to modulate the function of NMDA and GABA A receptors. Some of the proteins involved in copper transport are the transporters CTR1, ATP7A, and ATP7B and the chaperone ATOX1. There is limited information about the role of those biomolecules in the pathophysiology of Parkinson's disease; for instance, it is known that CTR1 is decreased in substantia nigra pars compacta in Parkinson's disease and that a mutation in ATP7B could be associated with Parkinson's disease. Regarding copper-related therapies, copper supplementation can represent a plausible alternative, while copper chelation may even aggravate the pathology. PMID:24672633

TiO2 effect on break-down of low-grade tantalum-niobium concentrates in the process of sulphatization

International Nuclear Information System (INIS)

Petrova, N.V.; Popov, A.D.; Mulenko, V.N.

1982-01-01

The effect of TiO 2 additive or materials containing it on tantalum-niobate decomposition in the process of sulphatization is investigated. It is shown that favourable effect of titanium dioxide in the process of sulphatization is especially noticeable in reprocessing of hard-brokening down tantalum-niobium concentrates with low Nb:Ta ratio etc. Chemical composition and type of tantalum-niobium mineralization of enrichment products used in the given investigation is presented. It is stated that the degree of concentrate break-down under similar sulphatization conditions (t=230 deg C; tau=2 h) essentially depends on the quantity of the introduced titanium dioxide. It is shown that sulphatization in the presence of titanium dioxide additive or materials containing it permits to exercise practically complete break-down of lean tantalum-niobium raw material, to avoid application of complexers in leaching of sulphatization products

The microbial communities and potential greenhouse gas production in boreal acid sulphate, non-acid sulphate, and reedy sulphidic soils

Czech Academy of Sciences Publication Activity Database

Šimek, Miloslav; Virtanen, S.; Simojoki, A.; Chroňáková, Alica; Elhottová, Dana; Krištůfek, Václav; Yli-Halla, M.

2014-01-01

Roč. 466, January (2014), s. 663-672 ISSN 0048-9697 R&D Projects: GA ČR GA526/09/1570; GA MŠk LC06066 Grant - others:GAJU(CZ) GAJU 138/2010/P Institutional support: RVO:60077344 Keywords : acid sulphate soil * carbon * CARD-FISH * microorganisms * nitrogen * PLFA Subject RIV: EE - Microbiology, Virology Impact factor: 4.099, year: 2014

Separation of copper-64 from copper phthalocyanine

International Nuclear Information System (INIS)

Battaglin, R.I.M.

1979-01-01

The separation of copper-64 from irradiated copper phthalocyanine by Szilard-Chalmers effect is studied. Two methods of separation are used: one of them is based on the dissolution of the irradiated dry compound in concentrated sulfuric acid following its precipitation in water. In the other one the compound is irradiated with water in paste form following treatment with water and hydrochloric acid. The influence of the crystal form of the copper phthalocyanine on the separation yield of copper-64 is shown. Preliminary tests using the ionic exchange technique for purification and changing of copper-64 sulfate to chloride form are carried out. The specific activity using the spectrophotometric technique, after the determination of the copper concentration in solution of copper-64, is calculated. (Author) [pt

Anisotropy in elastic properties of lithium sodium sulphate ...

Indian Academy of Sciences (India)

Anisotropy in elastic properties of lithium sodium sulphate hexahydrate single crystal—An ultrasonic study. GEORGE VARUGHESE. ,∗. , A S KUMAR†, J PHILIP†† and GODFREY LOUIS#. Department of Physics, Catholicate College, Pathanamthitta 689 648, India. †SPAP, M.G. University, Kottayam 686 560, India. ††STIC ...

calcium sulphate hemihydrate and bioactive glass composites for ...

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 41; Issue 2. In vitro bioactivity evaluation of α -calcium sulphate hemihydrate and bioactive glass composites for their potential use in bone regeneration. YANYAN ZHENG CHENGDONG XIONG DUJUAN ZHANG LIFANG ZHANG. Volume 41 Issue 2 April 2018 Article ID ...

Conductance and bulk vertical detachment energy of hydrated sulphate and oxalate dianions: a theoretical study

Science.gov (United States)

Pathak, Arup Kumar

2014-06-01

Analytical expressions have been derived for the vertical detachment energy (VDE) for hydrated sulphate (SO2 -4) and oxalate (C2O2 -4) dianions that can be used to calculate the same over a wide range of cluster sizes including the bulk from the knowledge of VDE for a finite number of stable clusters. The calculated bulk detachment energies are found to be very good in agreement (within 5%) with the available experimental results for both the systems. It is observed that two or more water molecules will be essential for the stability of sulphate and oxalate dianions against spontaneous electron loss and this is consistent with the experiment. We have, for the first time, provided a scheme to calculate the radius of the solvent berg for sulphate and oxalate dianions. The calculated conductivity values for the sulphate and oxalate dianions using Stokes-Einstein relation and the radius of solvent berg are found to be very good in agreement (within 4%) with the available experimental results.

Toxic effects of chromic sulphate on the common carp, Cyprinus carpio

Energy Technology Data Exchange (ETDEWEB)

Wong, M.H.; Lau, W.M.; Tong, T.Y.; Liu, W.K.; Luk, K.C.

1982-02-01

The effects of chromic sulphate, which is commonly used in the tanning of leather, on the common carp, Cyprinus carpio and the bighead, Aristichthys nobilis, were studied. C. carpio was found to be more susceptible than A. nobilis to chromic sulphate at the lowest concentration tested (100 mg/l) whereas results obtained at other concentration were similar for both species. Damage to the gills, liver and intestine was observed by histopathological examination. A wide range of chemicals is used in the different stages of treating leather and a possible treatment of the effluent from the tanneries is suggested.

Performance of Periwinkle Shell Ash Blended Cement Concrete Exposed to Magnesium Sulphate

Directory of Open Access Journals (Sweden)

Umoh A.A.

2013-01-01

Full Text Available The study examined the compressive strength of periwinkle shell ash (PSA blended cement concrete in magnesium sulphate medium. Specimens were prepared from designed characteristics strength of 25 MPa. The cement replacement with PSA ranged between 0 and 40% by volume. A total of 180 cube specimens were cast and cured in water. At 28 days curing, 45 specimens each were transferred into magnesium sulphate of 1%, 3%, and 5% solution, while others were continuously cured in water and tested at 62, 92, and 152 days. The results revealed a higher loss in compressive strength with the control mix, and that it increases with increased in MgSO4 concentration and exposure period, whereas, the attack on the PSA blended cement concrete was less and the least value recorded by 10% PSA content. Therefore, the study concluded that the optimum percentage replacement of cement with 10% PSA could mitigate magnesium sulphate attack.

Gasification of sulphate soap for the lime kiln

Energy Technology Data Exchange (ETDEWEB)

Saviharju, Kari (Valtion Teknillinen Tutkimuskeskus, Espoo (Finland). Lab. of Fuel and Process Technology); Timonen, Tuomas (Finnish Energy Economy Association, Espoo (Finland). Finnish Recovery Boiler Committee)

1993-01-01

Sulphate soap is a by-product of pulp mills utilized as a raw material for the chemical industry. However, this results in an increase in sulphur input of several kilograms SO[sub 2] per ADt pulp into the mill. Another increasingly interesting alternative is to utilize soap in the lime kiln of the mill. This has a positive effect, in addition to sulphur problems, on the energy balance of the mill. The crucial problem is the high Na + K content of soap, from 4 to 8%, which can result in plugging of the lime kiln. The operational problems can be avoided by gasifying the soap and by separating the inorganic materials from the product gas before the kiln. This paper describes research work on the gasification of crude sulphate soap carried out at the Technical Research Centre of Finland (VTT) over the years 1991 and 1992. This work will be continued in 1993 by focusing on specified problems, after which commercial applications should be available. (author)

Coastal acid sulphate soils in Poland: a review

Directory of Open Access Journals (Sweden)

Hulisz Piotr

2017-03-01

Full Text Available This paper presents the state of knowledge on coastal acid sulphate soils in Poland. The properties of these soils are closely related to the influence of brackish water from the Baltic Sea, high accumulation of organic matter and human activity. The obtained results demonstrate that the sulphide accumulation in soils refers to a relatively small areas of the Polish coastal zone with the unique and very valuable habitats. They require an adequate regulation of the water relations to avoid the risk of strong soil acidification and environmental pollution by heavy metals. Currently, there are no relevant criteria for classification of acid sulphate soil materials in the Polish Soil Classification (2011. Therefore, based on the presented data, the authors proposed to identify these features at the lower classification level (for different soil types. The criteria for the Thionic and Sulfidic qualifiers used in the WRB classification (IUSS Working Group WRB 2015 could be accepted for this purpose.

Presidential Green Chemistry Challenge: 2002 Designing Greener Chemicals Award

Science.gov (United States)

Presidential Green Chemistry Challenge 2002 award winner, Chemical Specialties, developed an alkaline copper quaternary wood preservative to replace chromated copper arsenate preservative phased out due to risk to children.

Uptake and metabolism of sulphated steroids by the blood-brain barrier in the adult male rat.

Science.gov (United States)

Qaiser, M Zeeshan; Dolman, Diana E M; Begley, David J; Abbott, N Joan; Cazacu-Davidescu, Mihaela; Corol, Delia I; Fry, Jonathan P

2017-09-01

Little is known about the origin of the neuroactive steroids dehydroepiandrosterone sulphate (DHEAS) and pregnenolone sulphate (PregS) in the brain or of their subsequent metabolism. Using rat brain perfusion in situ, we have found 3 H-PregS to enter more rapidly than 3 H-DHEAS and both to undergo extensive (> 50%) desulphation within 0.5 min of uptake. Enzyme activity for the steroid sulphatase catalysing this deconjugation was enriched in the capillary fraction of the blood-brain barrier and its mRNA expressed in cultures of rat brain endothelial cells and astrocytes. Although permeability measurements suggested a net efflux, addition of the efflux inhibitors GF120918 and/or MK571 to the perfusate reduced rather than enhanced the uptake of 3 H-DHEAS and 3 H-PregS; a further reduction was seen upon the addition of unlabelled steroid sulphate, suggesting a saturable uptake transporter. Analysis of brain fractions after 0.5 min perfusion with the 3 H-steroid sulphates showed no further metabolism of PregS beyond the liberation of free steroid pregnenolone. By contrast, DHEAS underwent 17-hydroxylation to form androstenediol in both the steroid sulphate and the free steroid fractions, with some additional formation of androstenedione in the latter. Our results indicate a gain of free steroid from circulating steroid sulphates as hormone precursors at the blood-brain barrier, with implications for ageing, neurogenesis, neuronal survival, learning and memory. © 2017 International Society for Neurochemistry.

Two case studies on the origin of aqueous sulphate in deep crystalline rocks

International Nuclear Information System (INIS)

Michelot, J.L.; Fontes, J.C.

1987-01-01

The paper reports preliminary results obtained from studies in Central Sweden (Stripa) and in Northern Switzerland (Boettstein). The isotopic compositions ( 34 S, 18 O) of dissolved sulphates in shallow and deep groundwaters from the Stripa test site show that (1) the origins of the salinity in the shallow and in the deep groundwaters are probably different, (2) the low sulphate content of the waters collected from the upper part of the deep aquifer system could be derived from the shallow aqueous sulphate through bacterial reduction, (3) a deeper bulk of sulphate can be identified. After examining several hypotheses, a Permian or Triassic origin is attributed to this deep sulphate. Boettstein is the first drilled borehole of the NAGRA (Swiss National Co-operative for the Storage of Radioactive Wastes programme). In the 34 S versus 18 O diagram, most of the representative points of samples collected at different depths (from apparently different water bodies), lie along a straight line. It seems that this line cannot be a reduction line, nor a precipitation line (gypsum or anhydrite). It is thus interpreted as a mixing line. The end members of this mixing line are still unknown. However, a deep brine is present at the bottom of the system, probably related to brines circulating in the Permian channel found at the same depth, a few kilometres away. A working hypothesis involving this deep brine as a source for both end members of the mixing, through two different processes, is presented, with the problem of possible connections between the different water bodies. (author). 16 refs, 5 figs, 2 tabs

Measurement of dynamic wedge angles and beam profiles by means of MRI ferrous sulphate gel dosimetry

Science.gov (United States)

Bengtsson, Magnus; Furre, Torbjørn; Rødal, Jan; Skretting, Arne; Olsen, Dag R.

1996-02-01

The purpose of this study is to examine the possible value of measuring the dose distribution in dynamic wedge photon beams using ferrous sulphate gel phantoms analysed by MRI. The wedge angles and dose profiles were measured for a field size of and for dynamic wedge angles of , , and using a 15 MV photon beam generated from a Clinac 2100 CD (Varian). The dose profiles obtained from MRI ferrous sulphate gel were in good agreement with the dose measurements performed with a diode detector array. Also, the wedge angles determined from the MRI ferrous sulphate gel agreed well with the values obtained by using film dosimetry and with calculations by use of TMS (treatment planning system) (Helax, Uppsala, Sweden). The study demonstrated that MRI ferrous sulphate gel dosimetry is an adequate tool for measurements of some beam characteristics of dynamic radiation fields.

The trade-off of availability and growth inhibition through copper for the production of copper-dependent enzymes by Pichia pastoris.

Science.gov (United States)

Balakumaran, Palanisamy Athiyaman; Förster, Jan; Zimmermann, Martin; Charumathi, Jayachandran; Schmitz, Andreas; Czarnotta, Eik; Lehnen, Mathias; Sudarsan, Suresh; Ebert, Birgitta E; Blank, Lars Mathias; Meenakshisundaram, Sankaranarayanan

2016-02-20

Copper is an essential chemical element for life as it is a part of prosthetic groups of enzymes including super oxide dismutase and cytochrome c oxidase; however, it is also toxic at high concentrations. Here, we present the trade-off of copper availability and growth inhibition of a common host used for copper-dependent protein production, Pichia pastoris. At copper concentrations ranging from 0.1 mM (6.35 mg/L) to 2 mM (127 mg/L), growth rates of 0.25 h(-1) to 0.16 h(-1) were observed with copper uptake of as high as 20 mgcopper/gCDW. The intracellular copper content was estimated by subtracting the copper adsorbed on the cell wall from the total copper concentration in the biomass. Higher copper concentrations led to stronger cell growth retardation and, at 10 mM (635 mg/L) and above, to growth inhibition. To test the determined copper concentration range for optimal recombinant protein production, a laccase gene from Aspergillus clavatus [EMBL: EAW07265.1] was cloned under the control of the constitutive glyceraldehyde-3-phosphate (GAP) dehydrogenase promoter for expression in P. pastoris. Notably, in the presence of copper, laccase expression improved the specific growth rate of P. pastoris. Although copper concentrations of 0.1 mM and 0.2 mM augmented laccase expression 4 times up to 3 U/mL compared to the control (0.75 U/mL), while higher copper concentrations resulted in reduced laccase production. An intracellular copper content between 1 and 2 mgcopper/gCDW was sufficient for increased laccase activity. The physiology of the yeast could be excluded as a reason for the stop of laccase production at moderate copper concentrations as no flux redistribution could be observed by (13)C-metabolic flux analysis. Copper and its pivotal role to sustain cellular functions is noteworthy. However, knowledge on its cellular accumulation, availability and distribution for recombinant protein production is limited. This study attempts to address one such challenge

Selection of Suitable Carbon, Nitrogen and Sulphate Source for the Production of Alkaline Protease by Bacillus licheniformis NCIM-2042

Directory of Open Access Journals (Sweden)

Biswanath BHUNIA

2010-06-01

Full Text Available In this study, selection of suitable carbon, nitrogen and sulphate sources were carried out by one-variable-at-time approach for the production of alkaline protease enzyme by Bacillus licheniformis NCIM-2042. Maximum levels of alkaline protease were found in culture media supplemented with magnesium sulphate, starch and soybean meal as a good sulphate, carbon and nitrogen sources which influenced the maximum yield of this enzyme (137.694.57, 135.231.73 and 134.741.77, respectively in comparison with the other sulphate, carbon and nitrogen sources.

Behaviour of Type 316 steel in acidic sulphate solutions at 300-3500C

International Nuclear Information System (INIS)

Newman, J.F.

1987-11-01

Most cation resin beds in service in CEGB power stations, and particularly those in AGR stations, are regenerated with sulphuric acid. Slippage results in trace levels of sulphate passing into the boilers. Previous work has shown that in once-through boilers, feedwater containing 2 μg kg -1 of sulphate could concentrate at localized dry-out sites to form solutions having from 0.1 to 7 wt% of solute. It has been shown also that if the sulphate was present in an acidic solution and it were to be in contact with Type 316 austentitic superheater steel, then intergranular corrosion and intergranular cracking could occur. Previous data, including some unreported results, are tabulated and discussed. The current work had two main objectives. The first was to extend the previous investigations to examine a wider range of acidic sulphate concentrations (as indicated by calculations on the concentration of solute in feedwater), the influence of environment pH, and the effect of sensitization of specimens. The second objective was primarily concerned with elucidating the causes of scatter in the results. This involved examining the influence of electrode potential, the ageing characteristics of the environment, and the method of applying stress to the specimens. (author)

Optimisation of the zinc sulphate turbidity test for the determination of immune status.

Science.gov (United States)

Hogan, I; Doherty, M; Fagan, J; Kennedy, E; Conneely, M; Crowe, B; Lorenz, I

2016-02-13

Failure of passive transfer of maternal immunity occurs in calves that fail to absorb sufficient immunoglobulins from ingested colostrum. The zinc sulphate turbidity test has been developed to test bovine neonates for this failure. The specificity of this test has been shown to be less than ideal. The objective was to examine how parameters of the zinc sulphate turbidity test may be manipulated in order to improve its diagnostic accuracy. One hundred and five blood samples were taken from calves of dairy cows receiving various rates of colostrum feeding. The zinc sulphate turbidity test was carried out multiple times on each sample, varying the solution strength, time of reaction and wavelength of light used and the results compared with those of a radial immunodiffusion test, which is the reference method for measuring immunoglobulin concentration in serum. Reducing the time over which the reaction occurs, or increasing the wavelength of light used to read the turbidity, resulted in decreased specificity without improving sensitivity. Increasing the concentration of the zinc sulphate solution used in the test was shown to improve the specificity without decreasing sensitivity. Examination of the cut-off points suggested that a lower cut-off point would improve the performance. British Veterinary Association.

Short communication: Use of calcium sulphate dihydrate as an ...

African Journals Online (AJOL)

flocculant alternative to the conventional use of aluminium sulphate in the primary treatment of wastewater was evaluated using a jar test apparatus. Samples from the State Water Commission (CEA) in Queretaro, Mexico, were collected for the ...

Investigating the Changes of Sulphate in Potabale Water of Yasuj City and preparing it's Qualitative Plan by Means of GIS Tools

International Nuclear Information System (INIS)

Pasereh, F.; Hasani, A.; Hoseini, N.; Javid, A.

2016-01-01

Water has always some soluble salts, such as sulphate. Sulphate enters the water through different resources such as, dissolved gypsum, waste water of industrial factories and automobiles smoke, dissolved in rain. Presence of sulphate in potable water has an enormous role in creating constant hardness.On the other hand Presence of sulphate with high density in drinking water, causes changes in taste and it's combination with Calcium and Magnesium anions has laxative effect. The goal of this study is to assess the amount of existing sulphate in Yasuj city potable ground water, and determining the procedure of changes in chemical parameters of sulphate and recognizing effective factors on these parameters and preparing qualitative plan for water resources for sulphate parameter by means of GIS tools. Method: In the study described above, 42 specimens in the 7 early months of the year 1387 were acquired and tested. Sulphate tests were done based on the measuring method of the instrument of Filter photometer (Model: 7000). For analysing the results, Excel software and for preparing qualitative plan, GIS software was used. Findings: This study showed that sulfate levels in water resources by reducing water level in summer and autumn and with a water level of under ground water resources increases. Discussion and Conclusion: Decrease of ground water resources of Yasuj city, causes the sulphate density to increase.

Biomass reduction of Salvinia molesta exposed to copper sulfate pentahydrate (CuSO4.5H2O

Directory of Open Access Journals (Sweden)

João Pedro Alves de Azevedo Barros

2015-07-01

Full Text Available Copper in the aquatic ecosystem may remain adsorbed or be incorporated into the biomass and undergo biomagnification causing unwanted effects to aquatic macrophyte communities. This study evaluated the biomass reduction of Salvinia molesta (Mitchell exposed to copper sulphate pentahydrate (CuSO4.5H2O under laboratory conditions. Approximately 20.5 g of fresh mass (FM of S. molesta (0.74 g dry matter, DM were placed in glass tanks with different concentrations (n = 3 of CuSO4.5H2O as follows: 0.0; 2.0; 4.0; 6.0; and 8.0 mg L-1 for 28 days. The dry mass was determined after each seven-day interval over 28 days and submitted to repeated ANOVA measures, followed by a Tukey test (P<0,05. The results show that macrophyte increased until the seventh day of exposure in all treatments. After this period, the biomass of S. molesta decreased; but there was no significant difference between treatments with copper, except for the 8.0 mg L-1 treatment. The copper treatments decreased the S. molesta biomass an average of 43.2% (0.50 g DM after 28 days. At the end of the experiment, copper absorption in the treatments with 6.0 and 8.0 mg L-1 was on average 77.9% higher than in the treatments with 2 and 4 mg L-1 . The treatments with 6.0 and 8.0 mg L-1 reached their maximum bioaccumulation capacity after 14 days. The results show that contamination of the aquatic environment at concentrations above 2 mg L-1 Cu2+ can reduce the S. molesta biomass by approximately 43%.

Influence of Height Waterlogging on Soil Physical Properties of Potential and Actual Acid Sulphate Soils

Directory of Open Access Journals (Sweden)

Arifin Fahmi

2014-06-01

Full Text Available Water management is main factor that determines the successful of rice cultivation in acid sulphate soil. Soil waterlogging determines the direction and rate of chemical, geochemical and biological reaction in the soil, indirectly these reactions may influence to the changes of soil psycal properties during soil waterlogging process. The experiment was aimed to study the changes of two type of acid sulphate soils physical properties during rice straw decomposition processes. The research was conducted in the greenhouse consisting of the three treatment factors using the completely randomized design with three replications. The first factor was soil type: potential acid sulphate soil (PASS and actual acid sulphate soil (AASS. The second factor was height of water waterlogging: 0.5-1.0 cm (muddy water–level condition and 4.0 cm from above the soil surface (waterlogged. The third factor was organic matter type: rice straw (RS, purun tikus (Eleocharis dulcis (PT and mixed of RS and PT (MX. Soil physical properties such as aggregate stability, total soil porosity, soil permeability, soil particle density and bulk density were observed at the end of experiment (vegetative maximum stage. The results showed that acid sulphate soil type had large effect on soil physicl properties, soil waterlogging decreased aggregate stability, soil particle density and bulk density both of soil type.

The Influence of Sempervivum Tectorum and Melatonin Administration on Erythrocyte Catalase in Rats Exposed to Aluminium Sulphate

Directory of Open Access Journals (Sweden)

Loredana Gabriela Stana

2012-10-01

Full Text Available The aim of the study was to highlight the effect of Sempervivum tectorum and melatonin administration in rats exposed to aluminium sulphate through drinking water on the erythrocyte catalase activity The researches were carried out on Wistar albinos rats, grouped in 8 lots: a control lot (C and 7 experimental lots (E1: 10% Sempervivum tectorum aqueous extract, 3 month; E2: melatonin, 10 mg/100 ml water, 3 month; E3: aluminium sulphate, 3 months; E4: aluminium sulphate with 10% Sempervivum tectorum aqueous extract, 3 months; E5: aluminium sulphate with melatonin 3 months; E6: aluminium sulphate 3 months followed by 10% Sempervivum tectorum aqueous extract for a month; E7: aluminium sulphate 3 months, followed by melatonin for a month. Al(3+ level in drinking water was 1000 ppb. It was registered decrease of catalase activity compared to C group in E3, E4 (p0.05 and an insignificant increase in E1, E2, E6, E7 groups. Sempervivum tectorum and melatonin administration led to the increase of catalase activity comparing to the group exposed only to aluminium. The catalase activity increase was significantly higher in case of consecutive administration to aluminium intake. Melatonin effect was more wellmarked as the one induced by Sempervivum tectorum (p>0.05.

Copper and copper-nickel alloys as zebra mussel antifoulants

Energy Technology Data Exchange (ETDEWEB)

Dormon, J.M.; Cottrell, C.M.; Allen, D.G.; Ackerman, J.D.; Spelt, J.K. [Univ. of Toronto, Ontario (Canada)

1996-04-01

Copper has been used in the marine environment for decades as cladding on ships and pipes to prevent biofouling by marine mussels (Mytilus edulis L.). This motivated the present investigation into the possibility of using copper to prevent biofouling in freshwater by both zebra mussels and quagga mussels (Dreissena polymorpha and D. bugensis collectively referred to as zebra mussels). Copper and copper alloy sheet proved to be highly effective in preventing biofouling by zebra mussels over a three-year period. Further studies were conducted with copper and copper-nickel mesh (lattice of expanded metal) and screen (woven wire with a smaller hole size), which reduced the amount of copper used. Copper screen was also found to be strongly biofouling-resistant with respect to zebra mussels, while copper mesh reduced zebra mussel biofouling in comparison to controls, but did not prevent it entirely. Preliminary investigations into the mechanism of copper antifouling, using galvanic couples, indicated that the release of copper ions from the surface of the exposed metal into the surrounding water is directly or indirectly responsible for the biofouling resistance of copper.

Treatment of food-agro (sugar industry wastewater with copper metal and salt: Chemical oxidation and electro-oxidation combined study in batch mode

Directory of Open Access Journals (Sweden)

Anurag Tiwari

2017-06-01

Full Text Available Sugar industry is one of the major industries which have been included in the polluting industries list by the World Bank. Different pollution monitoring agencies like State and National Pollution Control Boards have been made compulsory for each industry to set up a waste water treatment plants. In treatment system, single treatments of effluent are not effective to manage the dischargeable limit. So an attempted has been made to treat sugar industry wastewater with electrochemical and chemical process by using copper as electrode and chemical. Electrochemical process shows 81% chemical oxygen demand and 83.5% color reduction at pH 6, electrode distance 20 mm, current density 178 A m−2 and 120 min treatment time. The combined treatment results show 98% chemical oxygen demand and 99.5% color removal at 8 mM mass loading and pH 6 with copper sulphate.

Use of 16S rRNA-targeted oligonucleotide probes to investigate the distribution of sulphate-reducing bacteria in estuarine sediments.

Science.gov (United States)

Purdy, K J.; Nedwell, D B.; Embley, T M.; Takii, S

2001-07-01

The distribution of sulphate-reducing bacteria (SRBs) in three anaerobic sediments, one predominantly freshwater and low sulphate and two predominantly marine and high sulphate, on the River Tama, Tokyo, Japan, was investigated using 16S rRNA-targeted oligonucleotide probes. Hybridisation results and sulphate reduction measurements indicated that SRBs are a minor part of the bacterial population in the freshwater sediments. Only Desulfobulbus and Desulfobacterium were detected, representing 1.6% of the general bacterial probe signal. In contrast, the SRB community detected at the two marine-dominated sites was larger and more diverse, representing 10-11.4% of the bacterial signal and with Desulfobacter, Desulfovibrio, Desulfobulbus and Desulfobacterium detected. In contrast to previous reports our results suggest that Desulfovibrio may not always be the most abundant SRB in anaerobic sediments. Acetate-utilising Desulfobacter were the dominant SRB in the marine-dominated sediments, and Desulfobulbus and Desulfobacterium were active in low-sulphate sediments, where they may utilise electron acceptors other than sulphate.

Selection of Suitable Carbon, Nitrogen and Sulphate Source for the Production of Alkaline Protease by Bacillus licheniformis NCIM-2042

Directory of Open Access Journals (Sweden)

Biswanath BHUNIA

2010-06-01

Full Text Available In this study, selection of suitable carbon, nitrogen and sulphate sources were carried out by one-variable-at-time approach for the production of alkaline protease enzyme by Bacillus licheniformis NCIM-2042. Maximum levels of alkaline protease were found in culture media supplemented with magnesium sulphate, starch and soybean meal as a good sulphate, carbon and nitrogen sources which influenced the maximum yield of this enzyme (137.69�4.57, 135.23�1.73 and 134.74�1.77, respectively in comparison with the other sulphate, carbon and nitrogen sources.

The bioavailability of four zinc oxide sources and zinc sulphate in broiler chickens

OpenAIRE

Veldkamp, T.; Diepen, van, J.T.M.; Bikker, P.

2014-01-01

Zinc is an essential trace element for all farm animal species. It is commonly included in animal diets as zinc oxide, zinc sulphate or organically bound zinc. Umicore Zinc Chemicals developed zinc oxide products with different mean particle sizes. Umicore Zinc Chemicals requested Wageningen UR Livestock Research to determine the bioavailability of four zinc oxide sources and zinc sulphate in broiler chickens. A precise estimate of the bioavailability of zinc sources is required both for fulf...

Comparative proteomic analysis of the molecular responses of mouse macrophages to titanium dioxide and copper oxide nanoparticles unravels some toxic mechanisms for copper oxide nanoparticles in macrophages.

Directory of Open Access Journals (Sweden)

Sarah Triboulet

Full Text Available Titanium dioxide and copper oxide nanoparticles are more and more widely used because of their catalytic properties, of their light absorbing properties (titanium dioxide or of their biocidal properties (copper oxide, increasing the risk of adverse health effects. In this frame, the responses of mouse macrophages were studied. Both proteomic and targeted analyses were performed to investigate several parameters, such as phagocytic capacity, cytokine release, copper release, and response at sub toxic doses. Besides titanium dioxide and copper oxide nanoparticles, copper ions were used as controls. We also showed that the overall copper release in the cell does not explain per se the toxicity observed with copper oxide nanoparticles. In addition, both copper ion and copper oxide nanoparticles, but not titanium oxide, induced DNA strands breaks in macrophages. As to functional responses, the phagocytic capacity was not hampered by any of the treatments at non-toxic doses, while copper ion decreased the lipopolysaccharide-induced cytokine and nitric oxide productions. The proteomic analyses highlighted very few changes induced by titanium dioxide nanoparticles, but an induction of heme oxygenase, an increase of glutathione synthesis and a decrease of tetrahydrobiopterin in response to copper oxide nanoparticles. Subsequent targeted analyses demonstrated that the increase in glutathione biosynthesis and the induction of heme oxygenase (e.g. by lovastatin/monacolin K are critical for macrophages to survive a copper challenge, and that the intermediates of the catecholamine pathway induce a strong cross toxicity with copper oxide nanoparticles and copper ions.

Comparative proteomic analysis of the molecular responses of mouse macrophages to titanium dioxide and copper oxide nanoparticles unravels some toxic mechanisms for copper oxide nanoparticles in macrophages.

Science.gov (United States)

Triboulet, Sarah; Aude-Garcia, Catherine; Armand, Lucie; Collin-Faure, Véronique; Chevallet, Mireille; Diemer, Hélène; Gerdil, Adèle; Proamer, Fabienne; Strub, Jean-Marc; Habert, Aurélie; Herlin, Nathalie; Van Dorsselaer, Alain; Carrière, Marie; Rabilloud, Thierry

2015-01-01

Titanium dioxide and copper oxide nanoparticles are more and more widely used because of their catalytic properties, of their light absorbing properties (titanium dioxide) or of their biocidal properties (copper oxide), increasing the risk of adverse health effects. In this frame, the responses of mouse macrophages were studied. Both proteomic and targeted analyses were performed to investigate several parameters, such as phagocytic capacity, cytokine release, copper release, and response at sub toxic doses. Besides titanium dioxide and copper oxide nanoparticles, copper ions were used as controls. We also showed that the overall copper release in the cell does not explain per se the toxicity observed with copper oxide nanoparticles. In addition, both copper ion and copper oxide nanoparticles, but not titanium oxide, induced DNA strands breaks in macrophages. As to functional responses, the phagocytic capacity was not hampered by any of the treatments at non-toxic doses, while copper ion decreased the lipopolysaccharide-induced cytokine and nitric oxide productions. The proteomic analyses highlighted very few changes induced by titanium dioxide nanoparticles, but an induction of heme oxygenase, an increase of glutathione synthesis and a decrease of tetrahydrobiopterin in response to copper oxide nanoparticles. Subsequent targeted analyses demonstrated that the increase in glutathione biosynthesis and the induction of heme oxygenase (e.g. by lovastatin/monacolin K) are critical for macrophages to survive a copper challenge, and that the intermediates of the catecholamine pathway induce a strong cross toxicity with copper oxide nanoparticles and copper ions.

Reuse of partially sulphated CFBC ash as an SO{sub 2} sorbent

Energy Technology Data Exchange (ETDEWEB)

Wu, Y.; Jia, L.; Anthony, E.J. [Natural Resources Canada, Ottawa, ON (Canada). CANMET Energy; Nobili, M.; Telesca, A. [Basilicata Univ., Potenza (Italy). Dept. of Environmental Engineering and Physics; Montagnaro, F. [Naples Univ., Naples (Italy). Dept. of Chemistry

2010-06-15

Ash produced from circulating fluidized bed combustion (CFBC) boilers typically contains large amounts of unreacted calcium oxide (CaO) when limestone is added into the combustor for in situ removal of sulphur dioxide (SO{sub 2}). This paper reported on a study that evaluated the reactivation of partially sulphated ash obtained from an industrial circulating fluidized bed combustion (CFBC) boiler by hydration with liquid water and steam. A pilot-scale mini-CFBC was used to evaluate the results of reactivation on the bed ash by hydrating with liquid water and admixtures of sodium carbonate (Na{sub 2}CO{sub 3}) in solution or as powder. Re-sulphation tests on the hydrated samples were performed in a Cahn 1000 thermogravimetric analyzer (TGA) at 850 degrees C for 90 minutes in a simulated flue gas environment with sulphur dioxide (SO{sub 2}) concentration at 5000 ppm. Re-sulphation was carried out on unhydrated ash at the same conditions used in the baseline test. The TGA results showed that although liquid water and steam successfully hydrate and reactivate the unreacted CaO in the bed ash, the treated ashes sulphated to widely different extents. Attempts to reactivate fly ash with hydration failed, but the fly ash by itself was extremely reactive. When the treated ash was re-injected into the combustor with the fuel, the effect on SO{sub 2} removal efficiency was negligible if Na{sub 2}CO{sub 3} was added as powder. Doping with aqueous solution improved SO{sub 2} removal, but to a lesser extent than if only water hydration was used. Increasing the amount of water to reactivate the ash did not improve the sulphur capture capacity in the mini-CFBC. It was concluded that reactivation by water is the most practical way to reuse the partially sulphated bed ash as a sulphur sorbent. 21 refs., 7 tabs., 3 figs.

MATHEMATICAL MODELING FOR BENZYLPENICILIN POTASSIUM AND STREPTOMYCIN SULPHATE POTENCY DETERMINATION OF ASCOMICIN

Directory of Open Access Journals (Sweden)

Viviana Ciuca

2016-12-01

Full Text Available Ascomicin is an antibacterial unguent for treatment of local infections of skin, eyes, outer ear, in cattle, sheep, pig, dog and cat. The product contains two active substances: benzylpenicillin potassium (Penicillin G potassium and streptomycin sulphate. The main characteristic of commercial product is benzylpenicillin potassium and streptomycin sulphate potency. The potency is estimated by comparing the inhibition of growth of sensitive micro-organisms produced by known concentrations of the antibiotic to be examined and a reference substance. The validation study aims to demonstrate the determination of the potency of benzylpenicillin potassium and streptomycin sulphate, it is an appropriate analytical method, reproducible and meets the quality requirements of Ascomicin product. The paper establishes the performance characteristics of the method considered and identify the factors that influence these characteristics. The diameters of inhibition zones, directly proportional to the logarithm of the concentration of the antibiotic used for the assay, measured and calculated using statistical methods (Combistats Soft. The assay is designed in such a way that the mathematical model on which the potency equation is based can be proved to be valid. A parallel-line model is chosen. The two log dose response lines of the preparation under examination and the standard preparation are parallel; they are rectilinear over the range of doses used in the calculation. These conditions are verified by validity tests for a given probability (P = 0.05. The test is not valid unless the confidence limits (P = 0.95 are not less than 50 per cent and not more than 200 per cent of the estimated potency. The estimated potency is not less than 95 per cent and not more than 105 per cent of the stated potency. The stated potency is not less than 19400 international units/g benzylpenicillin potassium and 13960 international units/g streptomycin sulphate. The validation

Effect of clonidine and magnesium sulphate on anaesthetic consumption, haemodynamics and postoperative recovery: A comparative study

Directory of Open Access Journals (Sweden)

Manjushree Ray

2010-01-01

Full Text Available This randomised, placebo-controlled, double-blind study was designed to assess the effect of intravenous clonidine and magnesium sulphate on intraoperative haemodynamics, anaesthetic consumption and postoperative recovery. Seventy five patients undergoing elective upper limb orthopaedic surgery were randomised into three groups. Group C received clonidine 3 μg/kg as a bolus before induction and 1μg/kg/hour by infusion intraopertively. Group M received magnesium sulphate 30 mg/kg as a bolus before induction and 10 mg/kg/hour by infusion. Group P received same volume of isotonic saline. Anaesthesia was induced and maintained with fentanyl citrate and propofol. Muscular relaxation was achieved by vecuronium bromide. Induction time, recovery time and consumption of propofol as well as fentanyl citrate were recorded. Induction of anaesthesia was rapid with both clonidine and magnesium sulphate. Time of bispectral index (BIS to reach 60 was significantly lower in Group C and Group M (P < 0.0001. Requirements of propofol and fentanyl were significantly less in Group C and Group M (P < 0.001. Postoperative recovery was slower in Group M compared with other two groups (P < 0.001. Perioperative use of both clonidine and magnesium sulphate significantly reduced the consumption of propofol and fentanyl citrate. Magnesium sulphate caused a delayed recovery.

Highly sulphated galactan from Halymenia durvillei (Halymeniales, Rhodophyta), a red seaweed of Madagascar marine coasts.

Science.gov (United States)

Fenoradosoa, T A; Delattre, C; Laroche, C; Wadouachi, A; Dulong, V; Picton, L; Andriamadio, P; Michaud, P

2009-08-01

Halymenia durvillei is a red seaweed with a great potential as sulphated galactan producer collected in the coastal waters of small island of Madagascar (Nosy-be in Indian Ocean). To elucidate the structure of its polysaccharide, NMR (1H and 13C), FTIR, HPAEC and different colorimetric methods were carried out. It has been shown that this polysaccharide, consisted mainly of galactose, was branched by xylose and galactose in minor amounts. Arabinose and fucose were also detected. This galactan was found highly sulphated (42%, w/w) and pyruvylated (1.8%, w/w). Analysis of glycosidic linkages by CPG-MS and 13C NMR indicated that the polysaccharide has the defining linear backbone of alternating 3-beta-D-galactopyranosyl units and 4-linked alpha-L/D-galactopyranosyl residues. 3,6-Anhydrogalactose units have been also detected in minor quantity. This lambda-carrageenan like polysaccharide has shown original sulphatation patterns with 2-O (26%) or 2/6-O (58%) sulphated 3-linked beta-D-galactopyranosyl units and 6-O (19%) or 2/6-O (47%) 4-linked alpha-L/D-galactopyranosyl residues.

Copper and Copper Proteins in Parkinson’s Disease

Directory of Open Access Journals (Sweden)

Sergio Montes

2014-01-01

Full Text Available Copper is a transition metal that has been linked to pathological and beneficial effects in neurodegenerative diseases. In Parkinson’s disease, free copper is related to increased oxidative stress, alpha-synuclein oligomerization, and Lewy body formation. Decreased copper along with increased iron has been found in substantia nigra and caudate nucleus of Parkinson’s disease patients. Copper influences iron content in the brain through ferroxidase ceruloplasmin activity; therefore decreased protein-bound copper in brain may enhance iron accumulation and the associated oxidative stress. The function of other copper-binding proteins such as Cu/Zn-SOD and metallothioneins is also beneficial to prevent neurodegeneration. Copper may regulate neurotransmission since it is released after neuronal stimulus and the metal is able to modulate the function of NMDA and GABA A receptors. Some of the proteins involved in copper transport are the transporters CTR1, ATP7A, and ATP7B and the chaperone ATOX1. There is limited information about the role of those biomolecules in the pathophysiology of Parkinson’s disease; for instance, it is known that CTR1 is decreased in substantia nigra pars compacta in Parkinson’s disease and that a mutation in ATP7B could be associated with Parkinson’s disease. Regarding copper-related therapies, copper supplementation can represent a plausible alternative, while copper chelation may even aggravate the pathology.

CHRONIC Cd TOXICITY OF BEAN PLANTS CAN BE PARTIALLY REDUCED BY SUPPLY OF AMMONIUM SULPHATE

Directory of Open Access Journals (Sweden)

Andon VASSILEV

2006-05-01

Full Text Available The effect of ammonium sulphate supply on plant Cd uptake, growth and photosynthesis of bean plants (cv. Limburgse vroege grown in Cd-contaminated artifi cial soil was studied. The experiments were performed at controlled conditions in absence or presence of Cd (0 or 50 mg Cd kg-1 soil and with or without supply of ammonium sulphate [0 or 0.687 g (NH42SO4 kg-1]. Cadmium inhibited both growth and photosynthetic activity of bean plants. The supply of ammonium sulphate had no signifi cant effect on plant Cd uptake and growth inhibition, but to some extend, reduced Cd-induced stress and its negative impact on the photosynthetic performance.

A novel anti-influenza copper oxide containing respiratory face mask.

Directory of Open Access Journals (Sweden)

Gadi Borkow

Full Text Available BACKGROUND: Protective respiratory face masks protect the nose and mouth of the wearer from vapor drops carrying viruses or other infectious pathogens. However, incorrect use and disposal may actually increase the risk of pathogen transmission, rather than reduce it, especially when masks are used by non-professionals such as the lay public. Copper oxide displays potent antiviral properties. A platform technology has been developed that permanently introduces copper oxide into polymeric materials, conferring them with potent biocidal properties. METHODOLOGY/PRINCIPAL FINDINGS: We demonstrate that impregnation of copper oxide into respiratory protective face masks endows them with potent biocidal properties in addition to their inherent filtration properties. Both control and copper oxide impregnated masks filtered above 99.85% of aerosolized viruses when challenged with 5.66+/-0.51 and 6.17+/-0.37 log(10TCID(50 of human influenza A virus (H1N1 and avian influenza virus (H9N2, respectively, under simulated breathing conditions (28.3 L/min. Importantly, no infectious human influenza A viral titers were recovered from the copper oxide containing masks within 30 minutes (< or = 0.88 log(10TCID(50, while 4.67+/-1.35 log(10TCID(50 were recovered from the control masks. Similarly, the infectious avian influenza titers recovered from the copper oxide containing masks were < or = 0.97+/-0.01 log(10TCID(50 and from the control masks 5.03+/-0.54 log(10TCID(50. The copper oxide containing masks successfully passed Bacterial Filtration Efficacy, Differential Pressure, Latex Particle Challenge, and Resistance to Penetration by Synthetic Blood tests designed to test the filtration properties of face masks in accordance with the European EN 14683:2005 and NIOSH N95 standards. CONCLUSIONS/SIGNIFICANCE: Impregnation of copper oxide into respiratory protective face masks endows them with potent anti-influenza biocidal properties without altering their physical

The bioactivation procedure for increasing the sulphate-reducing bacteria in a UASB reactor

Directory of Open Access Journals (Sweden)

M. M. M. Gonçalves

2005-12-01

Full Text Available Bioactivation, a procedure to obtain anaerobic sulphidogenic sludge, was developed in order to increase sulphate reduction and, consequently, sulphide production to remove metals from effluents. This procedure, in which the source of carbon/energy (lactate is gradually replaced, consisted of three operational conditions. It was observed that bioactivation took six months so there was a 100-fold increase in the population of sulphate-reducing bacteria estimated by the most-probable-number (MPN when molasses was employed as a new source.

Formation of sulphite, cysteic acid and taurine from sulphate by the egg embryo

International Nuclear Information System (INIS)

Chapeville, F.; Fromageot, P.

1959-01-01

It is shown that the formation of taurine from sulphate by the chicken embryo involves the reduction of sulphate to sulphite (I), the synthesis of cysteic acid (II) and its decarboxylation (Ill). The reaction (I) takes place in the vitellin sac. The reaction (II) results from the condensation of the sulphite with a-amino-acrylic acid and is carried out by the yolk. The enzymes responsible for the decarboxylation (III) are distributed both in the embryo and in its appendages. (author) [fr

Copper carrier protein in copper toxic sheep liver

Energy Technology Data Exchange (ETDEWEB)

Harris, A L; Dean, P D.G.

1973-01-01

The livers of copper-toxic sheep have been analyzed by gel electrophoresis followed by staining the gels for copper with diethyldithiocarbamate and for protein with amido schwartz. These gels were compared with similar gels obtained from the livers of normal and copper-deficient animals. The copper-toxic livers contained an extra protein band which possessed relatively weakly bound copper. Possible origins of this protein are discussed. 8 references, 1 figure, 2 tables.

[Need for resuscitation in preterm neonates less than 32 weeks treated with antenatal magnesium sulphate for neuroprotection].

Science.gov (United States)

Lloreda-Garcia, Jose María; Lorente-Nicolás, Ana; Bermejo-Costa, Francisca; Martínez-Uriarte, Juan; López-Pérez, Rocío

2016-01-01

Magnesium sulphate administration is recommended for foetal neuroprotection in pregnant women at imminent risk of early preterm birth. To evaluate the relationship between intrapartum magnesium sulphate for foetal neuroprotection and delivery room resuscitation of preterm infants less 32 weeks. A prospective observational study was conducted on preterm infants less 32 weeks exposed to magnesium sulphate for neuroprotection, and a comparison made with another historic group immediately before starting this treatment. Cases in both groups that had not reached lung maturity with corticosteroids were rejected. The rates of resuscitation, morbidity and mortality for each of the groups were analysed and compared. There was a total of 107 preterm, with 56 exposed to magnesium sulphate. Rate of advanced resuscitation were similar between the two groups. There were no other differences in mortality, invasive mechanical ventilation, time to first stool, and other comorbidities. Intrapartum magnesium sulphate for foetal neuroprotection was not associated with an increased need for intensive delivery room resuscitation and other morbidities in these cohorts of less than 32 weeks preterm infants. Copyright © 2015 Sociedad Chilena de Pediatría. Publicado por Elsevier España, S.L.U. All rights reserved.

Production of ferric sulphate from pyrite by thiobacillus ferrooxidans. Application to uranium ore leaching

International Nuclear Information System (INIS)

Rouas, C.

1988-12-01

A process for uranium extraction by oxidizing solutions of ferric sulphate produced by T. ferrooxidans from pyrite is developed. A new counting method specific of T. ferrooxidans is designed. An uranium resistant wild strain, with oxidizing properties as high as the strain ATCC 19859, is isolated. Optimal conditions for ferric sulphate production from pyrite are defined (pH 1.8, density of the medium 1.2%, pyrite granulometry [fr

Ontario Hydro studies on copper corrosion under waste disposal conditions

International Nuclear Information System (INIS)

Lam, K.W.

1990-01-01

The corrosion rate of copper is generally greater in aerated solutions containing sulphide; also, in the presence of sulphide there is the fear that pitting may occur. Experiments have been carried out to study the corrosion of copper in deaerated groundwater/bentonite slurries with and without added sulphide for exposure periods from two months to one year. The groundwater contains 6500 ppm of chloride and 1000 ppm of sulphate. Tests were also performed in the presence of a 150 rad/h radiation field. In deaerated slurries at 75C the corrosion rate is less than 2 μm/a. With one addition of 10 mg/l sulphide, the rate increases by a factor of ten. With daily sulphide additions to deaerated solutions the corrosion rate initially falls but then rises and stabilizes after 15 days. In aerated solutions the corrosion increases over the first 25 days and then stabilizes. The corrosion rate of copper reached a steady value in 15 to 30 days. Rates are higher in aerated solutions, but the effect of adding sulphide is not so marked in aerated solutions as in unaerated solutions. The highest corrosion rate, less than 150 μm/a, was observed in aerated slurries saturated with sulphide. For deaerated solutions in the absence of sulphide the corrosion rate increases with temperature, but in aerated solutions the rate decreases. For solutions containing added sulphide the influence of temperature is negligible. The effect of a radiation field may be beneficial; in the presence of a radiation field the corrosion rate is less than 20 μm/a. After descaling the coupons showed a high density of irregularly shaped pits both in the presence and absence of sulphide, resulting from intergranular attack. The pitting factor for the highest corrosion rate is around 15

Effect of Minor Titanium Addition on Copper/Diamond Composites Prepared by Hot Forging

Science.gov (United States)

Yang, Fei; Sun, Wei; Singh, Ajit; Bolzoni, Leandro

2018-03-01

Copper/diamond composites have great potential to lead the next generation of advanced heat sink materials for use in high-power electronic devices and high-density integrated circuits because of their potential excellent properties of high thermal conductivity and close thermal expansion to the chip materials (e.g., Si, InP, GaAs). However, the poor wettability between copper and diamond presents a challenge for synthesizing copper/diamond composites with effective metallurgical bonding and satisfied thermal performance. In this article, copper/diamond composites were successfully prepared by hot forging of elemental copper and artificial diamond powders with small amounts (0 vol.%, 3 vol.% and 5 vol.%) of titanium additives. Microstructure observation and mechanical tests showed that adding minor titanium additions in the copper/diamond composite resulted in fewer cracks in the composites' microstructure and significantly improved the bonding between the copper and diamond. The strongest bonding strength was achieved for the copper/diamond composite with 3 vol.% titanium addition, and the possible reasons were discussed.

Occurrence of sulphate reducing bacteria (SRB associated with biocorrosion on metallic surfaces in a hydroelectric power station in Ibirama (SC - Brazil

Directory of Open Access Journals (Sweden)

Paulo Roberto Dantas Marangoni

2013-10-01

Full Text Available The aim of this study was evaluate, two methods for the detection and identification of sulphate reducing bacteria (SRB: ML medium and PCR with specific primers for SRB groups. SRB were detected through the selective medium only on carbon steel, which showed corrosion. Employing specific PCR primer, SBR were detected from all the metallic components assayed, even those that did not present visible corrosion spots, such stainless steel and copper alloys. Despite the presence or absence of corrosion at the later stages effectively by using the selective medium,, the initial stages of the corrosion could only be detected by the amplification of total DNA with SRB specific primers. The early detection of SRB could be employed for preventing the damages on metal surfaces before the installation of corrosion processes. Strategies for reducing the time spent on SRB isolation and identification could be auxiliary tools for controlling the corrosion of materials.

Lingual dyskinesia and tics: a novel presentation of copper-metabolism disorder.

Science.gov (United States)

Goez, Helly R; Jacob, Francois D; Yager, Jerome Y

2011-02-01

Copper is a trace element that is required for cellular respiration, neurotransmitter biosynthesis, pigment formation, antioxidant defense, peptide amidation, and formation of connective tissue. Abnormalities of copper metabolism have been linked with neurologic disorders that affect movement, such as Wilson disease and Menkes disease; however, the diagnosis of non-Wilson, non-Menkes-type copper-metabolism disorders has been more elusive, especially in cases with atypical characteristics. We present here the case of an adolescent with a novel presentation of copper-metabolism disorder who exhibited acute severe hemilingual dyskinesia and prominent tics, with ballismus of the upper limbs, but had normal brain and spinal MRI results and did not show any signs of dysarthria or dysphagia. His serum copper and ceruloplasmin levels were low, but his urinary copper level was elevated after penicillamine challenge. We conclude that copper-metabolism disorders should be included in the differential diagnosis for movement disorders, even in cases with highly unusual presentations, because many of them are treatable. Moreover, a connection between copper-metabolism disorders and tics is presented, to our knowledge, for the first time in humans; further investigation is needed to better establish this connection and understand its underlying pathophysiology.

Reuse of Partially Sulphated CFBC Ash as an SO2 Sorbent

Energy Technology Data Exchange (ETDEWEB)

Wu, Yinghai; Jia, Lufei; Anthony, E.J. [CanmetENERGY, 1 Haanel Drive, Ottawa, Ontario, K1A1M1 (Canada); Nobili, M.; Telesca, A. [Department of Environmental Engineering and Physics, University of Basilicata, Viale dell' Ateneo, Lucano 10, 85100 Potenza (Italy); Montagnaro, F. [Department of Chemistry, University of Naples ' Federico II' , Monte Sant' Angelo, 80126 Naples (Italy)

2010-06-15

Ashes produced from fluidized bed combustors (FBC) burning high-sulphur fuels often contain 20-30 % unreacted CaO because of the limestone added to remove SO2 in situ. This paper presents the results from experiments into reactivating partially sulphated FBC ash (both bed ash and fly ash) with liquid water, steam and sodium carbonate. The water- or steam-hydrated ashes were subsequently re-sulphated in a thermogravimetric analyzer (TGA) with simulated flue gas. The TGA results show that, while liquid water and steam successfully hydrate and reactivate the unreacted CaO in the bed ash, the treated ashes sulphated to widely different extents. Attempts to reactivate fly ash with hydration failed, although fly ash by itself is extremely reactive. A pilot-scale mini-circulating FBC (CFBC) was also used to evaluate the results of reactivation on the bed ash by hydrating with liquid water and admixtures of inorganic salt (Na2CO3) in the form of either powder or solution. When the treated ash was re-injected into the combustor with the fuel, the effect on SO2 removal efficiency was negligible if Na2CO3 was added as powder. Doping with aqueous solution resulted in enhanced SO2 removal; however, the extent was lower than the level achieved if only water hydration was employed. Increasing the amount of water (from 10% to 30%) to reactivate the ash did not improve the sulphur capture capacity in the mini-CFBC. Overall, this study suggests that the most practical way for re-use of the partially sulphated bed ash as a sulphur sorbent is reactivation by water. A proposal for utilization of the fly ash in an economically reasonable way is also discussed.

Kinetics of barium sulphate reaction crystallization in crystallizers with internal circulation

Directory of Open Access Journals (Sweden)

J. Koralewska

2008-06-01

Full Text Available Kinetic calculation results describing the observed nucleation and growth rates of barium sulphate crystals precipitated in an integrated reaction-crystallization process in a barium sulphate-ammonium chloride-water system are presented and analyzed. The scope of experiments included two continuous model DTM-type crystallizers (Draft Tube Magma with internal circulation of the suspension forced by a liquid jet-pump device responsible for stable and intensive enough ascending/descending flow of BaSO4 crystal magma in a mixing chamber. For comparison purposes the experimental data corresponding to a continuous DT (Draft Tube crystallizer with propeller agitator are presented and discussed. The various types of laboratory crystallizers used were fed with concentrated water solution of barium chloride (of 10 or 24 mass % and - in a stoichiometric proportion - crystalline ammonium sulphate, assuming isothermal (348 K and hydrodynamic (average residence time of suspension in a crystallizer: 900 s process conditions. The observed nucleation and growth rates of barium sulphate crystals were estimated on the basis of crystal size distributions (CSDs using convenient calculation scheme derived for an MSMPR (Mixed Suspension Mixed Product Removal model approach. Considering the experimental population density distribution courses, a size-dependent growth (SDG phenomenon was taken into account in the kinetic calculations. Five SDG kinetic models recommended in the accessible literature were used for kinetic parameter values estimation. It was proved statistically, that Rojkowski’s two SDG models (hyperbolic and exponential best suit for our own experimental data description. The experimental data presented can be practically applied for improving the constructions of liquid jet-pump DTM crystallizers recommended for reaction crystallization of sparingly soluble inorganic salts (especially for high concentrations of reaction substrates in the modern

Structure of sodium alkyl sulphate micelles

International Nuclear Information System (INIS)

Vass, Sz.

1990-05-01

Micellar aggregation numbers of aggregated sodium octyl, decyl, dodecyl and tetradecyl sulphate molecules obtained from small-angle neutron scattering (SANS) measurements are reported. The surfactant concentration and solution temperature were varied systematically. A survey of the physical models and evaluation algorithms applied for SANS are presented. By utilizing a new least square fitting algorithm, the formation and annihilation parameters of orthopositronium in the micellar pseudophase and in the aqueous solvent is deduced by evaluating positron lifetime spectra measured by conventional technqiues. (R.P.) 157 refs.; 10 figs

Effect of anhydrous magnesium sulphate fertilizer and cutting ...

African Journals Online (AJOL)

Effect of anhydrous magnesium sulphate fertilizer on Panicum maximum yield and chemical composition of the resultant herbage harvested at 3, 4 and 5 weeks of age was investigated. The treatments were labeled T1 to T6. T1 was fertilized and harvested at 3 weeks cutting interval, T2 was fertilized and harvested at 4 ...

Precipitation of calcium sulphate on hot walls - influence of impurities, thermal and hydraulic effects

International Nuclear Information System (INIS)

Guillermin, Roger

1973-01-01

After some generalities on desalination by distillation processes and on problems due to scaling, this research thesis aims at a better understanding of the formation of deposits and their effects in the case of precipitation of calcium sulphate hemihydrate which precipitates above 100 C in pure solution and between 100 and 300 C in brine. Deposit growth, influence of impurities, and influence of the deposit on heat exchange and loss of load are the main issues of this research. The author addresses general principles of salt crystallization and the thermodynamic and kinetic aspects of calcium sulphate precipitation, studies the growth kinetics of the calcium sulphate hemihydrate in a transient concentration regime, reports the study of thermal and hydraulic effects of the formation of a hemihydrate deposit, notably by discussing the different phases involved in the covering of a metallic surface

[Concordance between the zinc sulphate flotation and centrifugal sedimentation methods for the diagnosis of intestinal parasites].

Science.gov (United States)

Inês, Elizabete De Jesus; Pacheco, Flavia Thamiris Figueiredo; Pinto, Milena Carneiro; Mendes, Patrícia Silva de Almeida; Da Costa-Ribeiro, Hugo; Soares, Neci Matos; Teixeira, Márcia Cristina Aquino

2016-12-01

The diagnosis of intestinal parasitic infections depends on the parasite load, the specific gravity density of the parasite eggs, oocysts or cysts, and the density and viscosity of flotation or sedimentation medium where faeces are processed. To evaluate the concordance between zinc sulphate flotation and centrifugal sedimentation in the recovery of parasites in faecal samples of children. Faecal samples of 330 children from day care centers were evaluated by zinc sulphate flotation and centrifugal sedimentation techniques. The frequencies of detection of parasites by each method were determined and the agreement between the diagnostic techniques was evaluated using the kappa index, with 95% confidence intervals. The faecal flotation in zinc sulphate diagnosed significantly more cases of Trichuris trichiura infection when compared to centrifugal sedimentation (39/330; 11.8% vs. 13/330; 3.9%, p<0.001), with low diagnostic concordance between methods (kappa=0.264; 95% CI: 0.102-0.427). Moreover, all positive samples for Enterobius vermicularis eggs (n=5) and Strongyloides stercoralis larvae (n=3) were diagnosed only by zinc sulphate. No statistical differences were observed between methods for protozoa identification. The results showed that centrifugal flotation in zinc sulphate solution was significantly more likely to detect light helminths eggs such as those of T. trichiura and E. vermicularis in faeces than the centrifugal sedimentation process.

Copper and copper-nickel-alloys - An overview

Energy Technology Data Exchange (ETDEWEB)

Klassert, Anton; Tikana, Ladji [Deutsches Kupferinstitut e.V. Am Bonneshof 5, 40474 Duesseldorf (Germany)

2004-07-01

With the increasing level of industrialization the demand for and the number of copper alloys rose in an uninterrupted way. Today, the copper alloys take an important position amongst metallic materials due to the large variety of their technological properties and applications. Nowadays there exist over 3.000 standardized alloys. Copper takes the third place of all metals with a worldwide consumption of over 15 millions tons per year, following only to steel and aluminum. In a modern industrial society we meet copper in all ranges of the life (electro-technology, building and construction industry, mechanical engineering, automotive, chemistry, offshore, marine engineering, medical applications and others.). Copper is the first metal customized by humanity. Its name is attributed to the island Cyprus, which supplied in the antiquity copper to Greece, Rome and the other Mediterranean countries. The Romans called it 'ore from Cyprus' (aes cyprium), later cuprum. Copper deposited occasionally also dapper and could be processed in the recent stone age simply by hammering. Already in early historical time copper alloys with 20 to 50 percent tin was used for the production of mirrors because of their high reflecting power. Although the elementary nickel is an element discovered only recently from a historical perspective, its application in alloys - without any knowledge of the alloy composition - occurred at least throughout the last 2.000 years. The oldest copper-nickel coin originates from the time around 235 B.C.. Only around 1800 AD nickel was isolated as a metallic element. In particular in the sea and offshore technology copper nickel alloys found a broad field of applications in piping systems and for valves and armatures. The excellent combination of characteristics like corrosion resistance, erosion stability and bio-fouling resistance with excellent mechanical strength are at the basis of this success. An experience of many decades supports the use

Decolourisation and degradation of textile dyes using a sulphate ...

African Journals Online (AJOL)

Successful decolourisation and degradation of textile dyes was achieved in a biosulphidogenic batch reactor using biodigester sludge from a local municipality waste treatment plant as a source of carbon and microflora that augmented a sulphate reducing bacteria (SRB) consortium. Orange II (O II) was decolourised by ...

Corrosion of copper in oxygen-deficient groundwater with and without deep bedrock micro-organisms: Characterisation of microbial communities and surface processes

Energy Technology Data Exchange (ETDEWEB)

Huttunen-Saarivirta, E., E-mail: elina.huttunen-saarivirta@vtt.fi [VTT Technical Research Centre of Finland, Materials Performance, Kemistintie 3, FI-02044 VTT (Finland); Rajala, P. [VTT Technical Research Centre of Finland, Materials Performance, Kemistintie 3, FI-02044 VTT (Finland); Bomberg, M. [VTT Technical Research Centre of Finland, Geobiotechnology, Tietotie 2, FI-02044 VTT (Finland); Carpén, L. [VTT Technical Research Centre of Finland, Materials Performance, Kemistintie 3, FI-02044 VTT (Finland)

2017-02-28

Highlights: • Copper was exposed to groundwater with and without deep bedrock micro-organisms. • Biofilm composition was determined and correlated with the behaviour of copper. • Under biotic conditions, the film of Cu{sub 2}S formed on copper surfaces. • Bacterial pool was in a key role for the morphology and properties of Cu{sub 2}S film. • Under abiotic conditions, Cu{sub 2}O systematically developed on copper surfaces. - Abstract: Copper specimens were exposed to oxygen-deficient artificial groundwater in the presence and absence of micro-organisms enriched from the deep bedrock of the planned nuclear waste repository site at Olkiluoto island on the western coast of Finland. During the exposure periods of 4 and 10 months, the copper specimens were subjected to electrochemical measurements. The biofilm developed on the specimens and the water used in the exposures were subjected to microbiological analyses. Changes in the water chemistry were also determined and surfaces of the copper specimens were characterized with respect to the morphology and composition of the formed corrosion products. The results showed that under biotic conditions, redox of the water and open circuit potential (OCP) of the copper specimens were generally negative and resulted in the build-up of a copper sulphide, Cu{sub 2}S, layer due to the activity of sulphate-reducing bacteria (SRB) that were included in the system. In the 4-month test, the electrochemical behaviour of the specimens changed during the exposure and alphaproteobactria Rhizobiales were the dominant bacterial group in the biofilm where the highest corrosion rate was observed. In the 10-month test, however, deltaproteobacteria SRB flourished and the initial electrochemical behaviour and the low corrosion rate of the copper were retained until the end of the test period. Under abiotic conditions, the positive water redox potential and specimen OCP correlated with the formation of copper oxide, Cu{sub 2}O

Corrosion of copper in oxygen-deficient groundwater with and without deep bedrock micro-organisms: Characterisation of microbial communities and surface processes

International Nuclear Information System (INIS)

Huttunen-Saarivirta, E.; Rajala, P.; Bomberg, M.; Carpén, L.

2017-01-01

Highlights: • Copper was exposed to groundwater with and without deep bedrock micro-organisms. • Biofilm composition was determined and correlated with the behaviour of copper. • Under biotic conditions, the film of Cu_2S formed on copper surfaces. • Bacterial pool was in a key role for the morphology and properties of Cu_2S film. • Under abiotic conditions, Cu_2O systematically developed on copper surfaces. - Abstract: Copper specimens were exposed to oxygen-deficient artificial groundwater in the presence and absence of micro-organisms enriched from the deep bedrock of the planned nuclear waste repository site at Olkiluoto island on the western coast of Finland. During the exposure periods of 4 and 10 months, the copper specimens were subjected to electrochemical measurements. The biofilm developed on the specimens and the water used in the exposures were subjected to microbiological analyses. Changes in the water chemistry were also determined and surfaces of the copper specimens were characterized with respect to the morphology and composition of the formed corrosion products. The results showed that under biotic conditions, redox of the water and open circuit potential (OCP) of the copper specimens were generally negative and resulted in the build-up of a copper sulphide, Cu_2S, layer due to the activity of sulphate-reducing bacteria (SRB) that were included in the system. In the 4-month test, the electrochemical behaviour of the specimens changed during the exposure and alphaproteobactria Rhizobiales were the dominant bacterial group in the biofilm where the highest corrosion rate was observed. In the 10-month test, however, deltaproteobacteria SRB flourished and the initial electrochemical behaviour and the low corrosion rate of the copper were retained until the end of the test period. Under abiotic conditions, the positive water redox potential and specimen OCP correlated with the formation of copper oxide, Cu_2O. Furthermore, in the absence of

Forest land cover continues to exacerbate freshwater acidification despite decline in sulphate emissions

International Nuclear Information System (INIS)

Dunford, Robert W.; Donoghue, Daniel N.M.; Burt, Tim P.

2012-01-01

Evidence from a multi-date regional-scale analysis of both high-flow and annual-average water quality data from Galloway, south-west Scotland, demonstrates that forest land cover continues to exacerbate freshwater acidification. This is in spite of significant reductions in airborne pollutants. The relationship between freshwater sulphate and forest cover has decreased from 1996 to 2006 indicating a decrease in pollutant scavenging. The relationship between forest cover and freshwater acidity (pH) is, however, still present over the same period, and does not show conclusive signs of having declined. Furthermore, evidence for forest cover contributing to a chlorine bias in marine ion capture suggests that forest scavenging of sea-salts may mean that the forest acidification effect may continue in the absence of anthropogenic pollutant inputs, particularly in coastal areas. - Highlights: ► Forest cover and water chemistry remain linked despite decreased sulphate emissions. ► Forest cover has significant relationships SO 4 2− , Cl − , Na + , pH, ANC and Na:Cl ratio. ► Forest cover: pH relationships shows some evidence of decline 1996–2006. ► Forest cover: freshwater sulphate relationships show evidence of decline 1996–2006. ► Natural forest-mechanisms may exacerbate acidification, particularly sea-salt scavenging. - Relationships between forest land cover and freshwater pH continue to be evident despite declines in anthropogenic pollutant sulphate deposition; sea-salt scavenging may play a role.

COMPARATIVE STUDY OF EPIDURAL FENTANYL AND FENTANYL PLUS MAGNESIUM SULPHATE FOR POSTOPERATIVE ANALGESIA

Directory of Open Access Journals (Sweden)

Shiva

2015-11-01

Full Text Available AIMS AND OBJECTIVES Magnesium has antinociceptive effects in animal and human models of pain. It is found that the addition of Magnesium sulphate to postoperative Epidural infusion of Fentanyl may decrease the need for Fentanyl. We undertook a study to compare the duration of postoperative analgesia after Epidural Fentanyl and Epidural Fentanyl plus Magnesium sulphate administered postoperatively, along with side effects. MATERIALS AND METHODS 50 patients undergoing elective lower limb and abdominal surgeries were randomized into one of the two groups with 25 patients in each group. Combined Spinal Epidural Anaesthesia was used for all patients. Spinal anaesthesia with 2.5 cc of 0.5% Hyperbaric Bupivacaine was given. When sensory blockade regressed to L1, patients were given either 50 µg of Fentanyl (diluted to 6cc with normal saline, Group F or 50 µg of Fentanyl plus 50 mg Magnesium sulphate (diluted to 6cc with normal saline, Group FM. Parameters like blood pressure, pulse rate, respiratory rate and oxygen saturation were monitored, and other side effects were noted. Data were analysed by using Student t test and Chi-square/ Fisher Exact tests. RESULTS There was significant difference in duration of analgesia between Group F (107 min and Group FM (143 min. Hemodynamic parameters were stable in both the groups with minimal side effects. CONCLUSION Co-administration of Magnesium sulphate with Fentanyl for postoperative Epidural analgesia results in prolongation of Fentanyl analgesia without significant side-effects.

Constant current chronopotentiometric stripping of sulphated polysaccharides

Czech Academy of Sciences Publication Activity Database

Strmečki, S.; Plavšić, M.; Ćosović, B.; Ostatná, Veronika; Paleček, Emil

2009-01-01

Roč. 11, č. 10 (2009), s. 2032-2035 ISSN 1388-2481 R&D Projects: GA ČR(CZ) GA301/07/0490; GA ČR(CZ) GP202/07/P497; GA MŠk(CZ) LC06035 Institutional research plan: CEZ:AV0Z50040507; CEZ:AV0Z50040702 Keywords : sulphated polysaccharides * ióta-carrageenan * catalysis of hydrogen evolution Subject RIV: BO - Biophysics Impact factor: 4.243, year: 2009

The Protective Role of Zinc Sulphate on Ethanol -Induced Liver and Kidney Damages in Rats

International Nuclear Information System (INIS)

Al-Damegh, Mona Abdalla

2007-01-01

Around the world more and more people suffer from alcoholism. Addiction problems, alcoholism and excessive use of drugs both medical and nonmedical, are major causes of liver and kidney damage in adults. The purpose of this study was to investigate on the protective role of zinc sulphate on liver and kidney in rats with acute alcoholism. Wistar albino rats were divided into four groups. Group I; control group, group 2; given only Zinc Sulphate (100 mg/kg/day for 3days), group 3; rats given absolute ethanol (1 ml of absolute ethanol administrated by gavage technique to each rat), group 4 given Zinc sulphate prior to the administration of absolute ethanol. The results of this study revealed that acute ethanol exposure caused degenerative morphological changes in the liver and kidney. Significant difference were found in the levels of serum, liver, kidney super oxide dismutase(SOD), catalase (CAT), nitric oxide(NO), and malondialdehyde (MDA) in the ethanol group compared to the control group. Moreover ,serum urea, creatnine, uric acid, alkaline phoshpatase and transaminases activities (GOTand GPT) were increased in the ethanol group compared to the control group. On the other hand,administration of zinc sulphate in the ethanol group caused a significant decrease in the degenerative changes, lipid peroxidation, antioxidant enzymes, and nitric oxide in serum, liver, and kidney. It can be concluded that zinc Sulphate has a protective role on the ethanol induced liver and kidney injury. In addition ,nitric oxide is involved in the mechanism of acute alcohol intoxication. (author)

Effects of dietary Aloe vera crude extracts on digestive enzyme ...

African Journals Online (AJOL)

Gabriel Gabriel

2017-10-16

Oct 16, 2017 ... bMineral premix (mg/kg dry diet): Ferrous sulphate 372, copper sulphate ..... spoilage, and oxidative degradation of polyunsaturated fatty acid, and consequently decreases the fish meat .... Int. J. Green Pharma.2, 152-154.

Precursors for formation of copper selenide, indium selenide, copper indium diselenide, and/or copper indium gallium diselenide films

Science.gov (United States)

Curtis, Calvin J; Miedaner, Alexander; Van Hest, Maikel; Ginley, David S

2014-11-04

Liquid-based precursors for formation of Copper Selenide, Indium Selenide, Copper Indium Diselenide, and/or copper Indium Galium Diselenide include copper-organoselenides, particulate copper selenide suspensions, copper selenide ethylene diamine in liquid solvent, nanoparticulate indium selenide suspensions, and indium selenide ethylene diamine coordination compounds in solvent. These liquid-based precursors can be deposited in liquid form onto substrates and treated by rapid thermal processing to form crystalline copper selenide and indium selenide films.

Thalassiolin D: a new flavone O-glucoside Sulphate from the seagrass Thalassia hemprichii.

Science.gov (United States)

Hawas, Usama W; Abou El-Kassem, Lamia T

2017-10-01

Thalassiolin D, a new flavone O-glucoside sulphate along with three flavonoids, two steroids, p-hydroxybenzoic acid, 4,4'-dihydroxybenzophenone and nitrogen compound, octopamine were isolated from the seagrass Thalassia hemprichii, collected from the Saudi Red Sea coast. By extensive spectroscopic analysis including 1D and 2D NMR and MS data, the structure of the new compound was elucidated as diosmetin 7-O-β-glucosyl-2″-sulphate. The new compound displayed moderately in vitro antiviral HCV protease activity with IC 50 value 16 μM.

Yield of castor bean fertilized with sewage sludge and potassium and magnesium sulphate

OpenAIRE

Cavalcanti,Thâmara F. M.; Zuba,Geraldo R.; Sampaio,Regynaldo A.; Carneiro,João P.; Oliveira,Ely S. A. de; Rodrigues,Márcio N.

2015-01-01

ABSTRACTThe aim of this study was to evaluate the yield and nutrition of castor bean in response to fertilization with sewage sludge and potassium (K) and magnesium (Mg) sulphate. The experiment was carried out from January to July 2011. The treatments, in a randomized block design with three replicates, in a Nitosol, corresponded to a factorial scheme (2 x 4 +1): two doses of K and Mg sulphate combined with four doses of sewage sludge (0, 2.60, 5.20 and 10.40 t ha-1, dry basis), applied base...

Endogenous and bioaugmented sulphate reduction in calcareous gypsiferous soils

NARCIS (Netherlands)

Alfaya, F.; Cuenca-Sanchez, M.; Garcia-Orenes, F.; Lens, P.N.L.

2009-01-01

Gypsiferous soils have a high agricultural value, but their utilization is limited by the presence of gypsum that can induce hardpan and vertical crusting. This paper reports on sulphate reduction in this soil type as a basis of a bioremediation technology to remove the gypsum content of calcareous

INVESTIGATION OF DISSOLVED SULPHATE IN VARIOUS GEOTHERMAL FIELDS OF SUMATRA USING OXYGEN AND SULPHUR ISOTOPES

Directory of Open Access Journals (Sweden)

E. Ristin Pujiindiyati

2010-06-01

Full Text Available There are at least 30 high temperature systems; eleven active volcanoes, five degassing volcanoes and one caldera volcano controlled by Sumatra Fault Zone over a length of 1700 km. To understand this geothermal field system, some information about geochemistry including isotope composition in its fluid is needed. Sulphur-34 and oxygen-18 isotopes in dissolved sulphate pair have been used to determine the origin of acidic fluid of sulphate and to evaluate the process involved. The fluids from eight hot springs, two fumaroles, four deep wells and crater have been collected in along Sumatra geothermal fields. Sulphur-34 (d 34S (SO4, 0/00 CDT and oxygen-18 (d 18O (SO4, 0/00 SMOW in sulphate is analyzed according to Robinson-Kusakabe and Rafter method, respectively. The d 34S (SO4 values from Sibayak wells are more enriched of 16.8 0/00 to 18.2 0/0 that may indicate the dissolution of anhydrite minerals or isotope partitioning in hydration of SO2. The d 34S (SO4 values from two fumaroles (Pusuk Bukit - North Sumatra and Rantau Dadap - South Sumatra are at depleted value of -0.150/00 and 1.80/00, those are close to d 34S from magmatic sulphur.  In general, the d 34S (SO4 of springs spread in a wide range of 5.250/00 to14.20/00 and show a mixing process between atmospheric sulphate and sulphate from deep wells. The d 18O (SO4 from wells exhibits depleted value around -3.60/00 suggesting that 87.5% of sulphate oxygen is derived from groundwater oxygen and 12.5% is derived from atmospheric molecular oxygen in sulphide oxidation reaction. In the other hand, hot springs (except Semurup, crater and fumaroles have enriched value of d 18O (SO4. These enriched values suggest that a higher percentage of atmospherically derived oxygen compared to those from the depth.   Keywords: isotope, geothermal, Sumatra

A reliable radiochromatographic assay technique for hepatic microsomal 16α-hydroxylase activity towards oestrone 3-sulphate

International Nuclear Information System (INIS)

Tsoutsoulis, C.J.; Hobkirk, R.

1980-01-01

A reliable procedure for the assay of liver microsomal 16α-hydroxylation of oestrone 3-sulphate has been developed for the guinea pig. It is based on the rapid, quantitative separation of oestradiol and oestriol by Sephadex LH-20 columns after the chemical reduction and enzymic hydrolysis of the incubation products. Microsomal preparations and incubation conditions that optimized 16α-hydroxylation of oestrone 3-sulphate were employed. Under these circumstances, reduction of the substrate at C-17 and hydrolysis of the sulphate were minimized. Conditions were established that yielded reaction linearity with respect to time and microsomal concentration. This hydroxylation had an absolute requirement for NADPH, which could not be satisfied by NADH. Apparent Ksub(m) values for oestrone 3-sulphate and NADPH, under the conditions used, were 14μM and 0.17mM respectively. 16α-hydroxylase activity was present in the liver microsomal fraction from heavily pigmented, female English Shorthaired guinea pigs. Much lower activity was detected in mature pigmented males and albino females. No activity could be demonstrated in mature, albino males. (author)

Advanced Copper Composites Against Copper-Tolerant Xanthomonas perforans and Tomato Bacterial Spot.

Science.gov (United States)

Strayer-Scherer, A; Liao, Y Y; Young, M; Ritchie, L; Vallad, G E; Santra, S; Freeman, J H; Clark, D; Jones, J B; Paret, M L

2018-02-01

Bacterial spot, caused by Xanthomonas spp., is a widespread and damaging bacterial disease of tomato (Solanum lycopersicum). For disease management, growers rely on copper bactericides, which are often ineffective due to the presence of copper-tolerant Xanthomonas strains. This study evaluated the antibacterial activity of the new copper composites core-shell copper (CS-Cu), multivalent copper (MV-Cu), and fixed quaternary ammonium copper (FQ-Cu) as potential alternatives to commercially available micron-sized copper bactericides for controlling copper-tolerant Xanthomonas perforans. In vitro, metallic copper from CS-Cu and FQ-Cu at 100 μg/ml killed the copper-tolerant X. perforans strain within 1 h of exposure. In contrast, none of the micron-sized copper rates (100 to 1,000 μg/ml) from Kocide 3000 significantly reduced copper-tolerant X. perforans populations after 48 h of exposure compared with the water control (P copper-based treatments killed the copper-sensitive X. perforans strain within 1 h. Greenhouse studies demonstrated that all copper composites significantly reduced bacterial spot disease severity when compared with copper-mancozeb and water controls (P copper composites significantly reduced disease severity when compared with water controls, using 80% less metallic copper in comparison with copper-mancozeb in field studies (P copper composites have the potential to manage copper-tolerant X. perforans and tomato bacterial spot.

Copper as a target for prostate cancer therapeutics: copper-ionophore pharmacology and altering systemic copper distribution

Science.gov (United States)

Denoyer, Delphine; Pearson, Helen B.; Clatworthy, Sharnel A.S.; Smith, Zoe M.; Francis, Paul S.; Llanos, Roxana M.; Volitakis, Irene; Phillips, Wayne A.; Meggyesy, Peter M.; Masaldan, Shashank; Cater, Michael A.

2016-01-01

Copper-ionophores that elevate intracellular bioavailable copper display significant therapeutic utility against prostate cancer cells in vitro and in TRAMP (Transgenic Adenocarcinoma of Mouse Prostate) mice. However, the pharmacological basis for their anticancer activity remains unclear, despite impending clinical trails. Herein we show that intracellular copper levels in prostate cancer, evaluated in vitro and across disease progression in TRAMP mice, were not correlative with copper-ionophore activity and mirrored the normal levels observed in patient prostatectomy tissues (Gleason Score 7 & 9). TRAMP adenocarcinoma cells harbored markedly elevated oxidative stress and diminished glutathione (GSH)-mediated antioxidant capacity, which together conferred selective sensitivity to prooxidant ionophoric copper. Copper-ionophore treatments [CuII(gtsm), disulfiram & clioquinol] generated toxic levels of reactive oxygen species (ROS) in TRAMP adenocarcinoma cells, but not in normal mouse prostate epithelial cells (PrECs). Our results provide a basis for the pharmacological activity of copper-ionophores and suggest they are amendable for treatment of patients with prostate cancer. Additionally, recent in vitro and mouse xenograft studies have suggested an increased copper requirement by prostate cancer cells. We demonstrated that prostate adenocarcinoma development in TRAMP mice requires a functional supply of copper and is significantly impeded by altered systemic copper distribution. The presence of a mutant copper-transporting Atp7b protein (tx mutation: A4066G/Met1356Val) in TRAMP mice changed copper-integration into serum and caused a remarkable reduction in prostate cancer burden (64% reduction) and disease severity (grade), abrogating adenocarcinoma development. Implications for current clinical trials are discussed. PMID:27175597

Sulphation and carbonation properties of hydrated sorbents from a fluidized bed CO{sub 2} looping cycle reactor

Energy Technology Data Exchange (ETDEWEB)

Vasilije Manovic; Edward J. Anthony; Dennis Y. Lu [CANMET Energy Technology Centre-Ottawa, Ottawa, ON (Canada)

2008-10-15

Sulphation and carbonation have been performed on hydrated spent residues from a 75 kW{sub th} dual fluidized bed combustion (FBC) pilot plant operating as a CO{sub 2} looping cycle unit. The sulphation and carbonation tests were done in an atmospheric pressure thermogravimetric analyzer (TGA), with the sulphation performed using synthetic flue gas (0.45% SO{sub 2}, 3% O{sub 2}, 15% CO{sub 2} and N{sub 2} balance). Additional tests were carried out in a tube furnace (TF) with a higher SO{sub 2} concentration (1%) and conversions were determined by quantitative X-ray diffraction (QXRD) analyses. The morphology of the sulphated samples from the TF was examined by scanning electron microscopy (SEM). Sulphation tests were performed at 850{sup o}C for 150 min and carbonation tests at 750{sup o}C, 10 cycles for 15 min (7.5 min calcination + 7.5 min carbonation). Sulphation conversions obtained for the hydrated samples depended on sample type: in the TGA, they were 75-85% (higher values were obtained for samples from the carbonator); and in the TF, values around 90% and 70% for sample from carbonator and calciner, respectively, were achieved, in comparison to the 40% conversion seen with the original sample. The SEM analyses showed significant residual porosity that can increase total conversion with longer sulphation time. The carbonation tests showed a smaller influence of the sample type and typical conversions after 10 cycles were 50% - about 10% higher than that for the original sample. The influence of hydration duration, in the range of 15-60 min, is not apparent, indicating that samples are ready for use for either SO{sub 2} retention, or further CO{sub 2} capture after at most 15 min using saturated steam. The present results show that, upon hydration, spent residues from FBC CO{sub 2} capture cycles are good sorbents for both SO{sub 2} retention and additional CO{sub 2} capture. 33 refs., 10 figs., 2 tabs.

Decolourisation and degradation of reactive blue 2 by sulphate ...

African Journals Online (AJOL)

This work was performed to determine the influence of heat treatment on sewage sludge and addition of zero valent iron (ZVI) on the degradation and decolourisation of an anthraquinone dye, reactive blue 2 (RB 2). A consortium of sulphate reducing bacteria (SRB) in a biosulphidogenic batch reactor with biodigester ...

Lead, zinc and copper fine powder with controlled size and shape

Directory of Open Access Journals (Sweden)

Mahmoud A Rabah

2017-12-01

Full Text Available This study describes the preparation of lead, zinc and copper powders by hydrometallurgy from secondary resources. Chloride, sulphate and acetate salts of zinc, copper and lead were prepared. The powders were prepared by reducing the ionic species of these metals by hydrazine hydrate or ascorbic acid. The effect of addition of some water soluble polar organic solvents to the aqueous salt solutions on the morphology and particle size of the prepared powder was studied. Findings were explained on the basis of the transition state theory and according to the Hughes and Ingold’s rule. Aqueous solutions alone produce metal powder having different size and irregular shape. The presence of polar organic solvents with high molecular weight and polarity produce powders having controlled size and regular morphology. The reason was because solvent polarity enhances the rate of red-ox reactions between metal ions and the reducing agent. The mean particle size of the powder was 60 um with zinc, 80 um with copper, and 90 um with lead. The extent of productivity was ≥98%. Results highlighted that the chemical reduction of the ionic species took place in a sequence steps. The first is a diffusion of the reactants across a boundary layer established at the polar site of the organic solvent molecules. The next step is the direct contact of the reactants. The third step involved reduction to yield powder. The last is the backward diffusion of the powder outside the boundary layer. Results showed that addition of water-miscible solvents having high dielectric constant increased the polarity of the medium. This energizes and enhances the one or more t step of the model to be more rapid to yield particles with small size and symmetrical shape.

The impact of sulphate and magnesium on chloride binding in Portland cement paste

Energy Technology Data Exchange (ETDEWEB)

De Weerdt, K., E-mail: klaartje.d.weerdt@ntnu.no [Department of Structural Engineering, Norwegian University of science and Technology, Trondheim (Norway); SINTEF Building and Infrastructure, Trondheim (Norway); Orsáková, D. [Department of Civil Engineering, Technical University of Brno, Brno (Czech Republic); Geiker, M.R. [Department of Structural Engineering, Norwegian University of science and Technology, Trondheim (Norway)

2014-11-15

The effect of magnesium and sulphate present in sea water on chloride binding in Portland cement paste was investigated. Ground well hydrated cement paste was exposed to MgCl{sub 2}, NaCl, NaCl + MgCl{sub 2}, MgSO{sub 4} + MgCl{sub 2} and artificial sea water solutions with a range of concentrations at 20 °C. Chloride binding isotherms are determined and pH of the solutions were measured. A selection of samples was examined by SEM-EDS to identify phase changes upon exposure. The experimental data were compared with calculations of a thermodynamic model. Chloride binding from sea water was similar to chloride binding for NaCl solutions. The magnesium content in the sea water lead to a slight decrease in pH, but this did not result in a notable increase in chloride binding. The sulphate present in sea water reduces both chloride binding in C–S–H and AFm phases, as the C–S–H incorporates more sulphates instead of chlorides, and part of the AFm phases converts to ettringite.

Native copper as a natural analogue for copper canisters

International Nuclear Information System (INIS)

Marcos, N.

1989-12-01

This paper discusses the occurrence of native copper as found in geological formations as a stability analogue of copper canisters that are planned to be used for the disposal of spent nuclear fuel in the Finnish bedrock. A summary of several publications on native copper occurrences is presented. The present geochemical and geohydrological conditions in which copper is met with in its metallic state show that metallic copper is stable in a wide range of temperatures. At low temperatures native copper is found to be stable where groundwater has moderate pH (about 7), low Eh (< +100 mV), and low total dissolved solids, especially chloride. Microscopical and microanalytical studies were carried out on a dozen of rock samples containing native copper. The results reveal that the metal shows no significant alteration. Only the surface of copper grains is locally coated. In the oldest samples there exist small corrosion cracks; the age of the oldest samples is over 1,000 million years. A review of several Finnish groundwater studies suggests that there are places in Finland where the geohydrological conditions are favourable for native copper stability. (orig.)

High dose, fast delivery magnesium sulphate in a 3-year-old acute severe asthmatic

Directory of Open Access Journals (Sweden)

John R Elton

2017-09-01

Full Text Available Acute severe asthma when respiratory failure is imminent is not addressed in world asthma guidelines. Intravenous magnesium sulphate, salbutamol and aminophylline all have advocates but what order, speed of delivery or dosage is left up to the individual physician treating the patient. A child in respiratory failure was given a large, fast dose of intravenous magnesium sulphate before intravenous salbutamol which relaxed bronchial smooth muscle immediately and tracheal intubation and lung ventilation was avoided. Justification for this treatment is discussed.

Sulphate reduction and nitrogen fixation rates associated with roots, rhizomes and sediments from Zostera noltii and Spartina maritima meadows.

Science.gov (United States)

Nielsen, L B; Finster, K; Welsh, D T; Donelly, A; Herbert, R A; de Wit, R; Lomstein, B A

2001-01-01

Sulphate reduction rates (SRR) and nitrogen fixation rates (NFR) associated with isolated roots, rhizomes and sediment from the rhizosphere of the marine macrophytes Zostera noltii and Spartina maritima, and the presence and distribution of Bacteria on the roots and rhizomes, were investigated. Between 1% and 3% of the surface area of the roots and rhizomes of both macrophytes were colonized by Bacteria. Bacteria on the surfaces of S. maritima roots and rhizomes were evenly distributed, while the distribution of Bacteria on Z. noltii roots and rhizomes was patchy. Root- and rhizome-associated SRR and NFR were always higher than rates in the bulk sediment. In particular, nitrogen fixation associated with the roots and rhizomes was 41-650-fold higher than in the bulk sediment. Despite the fact that sulphate reduction was elevated on roots and rhizomes compared with bulk sediment, the contribution of plant-associated sulphate reduction to overall sulphate reduction was small (< or =11%). In contrast, nitrogen fixation associated with the roots and rhizomes accounted for 31% and 91% of the nitrogen fixed in the rhizosphere of Z. noltii and S. maritima respectively. In addition, plant-associated nitrogen fixation could supply 37-1,613% of the nitrogen needed by the sulphate-reducing community. Sucrose stimulated nitrogen fixation and sulphate reduction significantly in the root and rhizome compartments of both macrophytes, but not in the bulk sediment.

Barium sulphate preparations for use in double contrast examination of the upper gastrointestinal tract

International Nuclear Information System (INIS)

Anderson, W.; Harthill, J.E.; James, W.B.; Montgomery, D.

1980-01-01

Physical properties relevant to upper gastrointestinal radiology have been compared for five barium sulphate preparations and related to radiographic results. Evaluation of particles (size and stability) and whole suspension (dispersibility and fluidity) resulted in ranking of the preparations generally in accord with that based on radiological experience in double contrast examinations of the stomach. Experiments with extirpated pig stomach revealed a tendency for large particles in a low viscosity barium sulphate suspension to settle in mucosal grooves. This is believed to contribute to good radiographic definition of both the areae gastricae and small lesions. Particle size is therefore important and susceptibility to flocculation, a possible cause of random change in size during use, was assessed by measuring particle electrophoretic mobility under varying conditions; quantitative differences in suspension flow and dispersibility were also demonstrated. Fluidity and dispersibility together with rapid sedimentation of suitably sized particles resistant to flocculation underlie the successful use of low viscosity high density barium sulphate suspensions. (U.K.)

Ovarian steroid sulphate functions as priming pheromone in male ...

Indian Academy of Sciences (India)

Unknown

The study reveals that pre-ovulatory females of the fish Barilius bendelisis (Ham.) release sex steroids and their conjugates into the water and that a steroid sulphate of these compounds functions as a potent sex pheromone which stimulates milt production in conspecific males prior to spawning. Since males exposed to the ...

Formation of copper-indium-selenide and/or copper-indium-gallium-selenide films from indium selenide and copper selenide precursors

Science.gov (United States)

Curtis, Calvin J [Lakewood, CO; Miedaner, Alexander [Boulder, CO; Van Hest, Maikel [Lakewood, CO; Ginley, David S [Evergreen, CO; Nekuda, Jennifer A [Lakewood, CO

2011-11-15

Liquid-based indium selenide and copper selenide precursors, including copper-organoselenides, particulate copper selenide suspensions, copper selenide ethylene diamine in liquid solvent, nanoparticulate indium selenide suspensions, and indium selenide ethylene diamine coordination compounds in solvent, are used to form crystalline copper-indium-selenide, and/or copper indium gallium selenide films (66) on substrates (52).

Lowering Low-Density Lipoprotein Particles in Plasma Using Dextran Sulphate Co-Precipitates Procoagulant Extracellular Vesicles

Directory of Open Access Journals (Sweden)

Jiong-Wei Wang

2017-12-01

Full Text Available Plasma extracellular vesicles (EVs are lipid membrane vesicles involved in several biological processes including coagulation. Both coagulation and lipid metabolism are strongly associated with cardiovascular events. Lowering very-low- and low-density lipoprotein ((VLDL particles via dextran sulphate LDL apheresis also removes coagulation proteins. It remains unknown, however, how coagulation proteins are removed in apheresis. We hypothesize that plasma EVs that contain high levels of coagulation proteins are concomitantly removed with (VLDL particles by dextran sulphate apheresis. For this, we precipitated (VLDL particles from human plasma with dextran sulphate and analyzed the abundance of coagulation proteins and EVs in the precipitate. Coagulation pathway proteins, as demonstrated by proteomics and a bead-based immunoassay, were over-represented in the (VLDL precipitate. In this precipitate, both bilayer EVs and monolayer (VLDL particles were observed by electron microscopy. Separation of EVs from (VLDL particles using density gradient centrifugation revealed that almost all coagulation proteins were present in the EVs and not in the (VLDL particles. These EVs also showed a strong procoagulant activity. Our study suggests that dextran sulphate used in LDL apheresis may remove procoagulant EVs concomitantly with (VLDL particles, leading to a loss of coagulation proteins from the blood.

Recent Insights into Cell Surface Heparan Sulphate Proteoglycans and Cancer

DEFF Research Database (Denmark)

Couchman, John R; Multhaupt, Hinke; Sanderson, Ralph D

2016-01-01

behaviour. Here, we review some recent advances, emphasising that many tumour-related functions of proteoglycans are revealed only after their modification in processes subsequent to synthesis and export to the cell surface. These include enzymes that modify heparan sulphate structure, recycling of whole...

Sulphur-oxidising and Sulphate-reducing Communities in Brazilian Mangrove Sediments

NARCIS (Netherlands)

Varon-Lopez, Maryeimy; Dias, A.C.F; Fasanella, C.C.; Durrer, A.; Melo, I.S.; Kuramae, E.E.; Andreote, F.D.

2014-01-01

Mangrove soils are anaerobic environments rich in sulphate and organic matter. Although the sulphur cycle is one of the major actors in this ecosystem, little is known regarding the sulphur bacteria communities in mangrove soils. We investigated the abundance, composition and diversity of

Bio-corrosion of water pipeline by sulphate-reducing bacteria in a ...

African Journals Online (AJOL)

esiri

2013-11-13

Nov 13, 2013 ... Key words: Sulphate-reducing bacteria, corrosion, water pipeline, biocide. INTRODUCTION ... small amount of organic material required to produce biomass):. )1(. 3. 2 .... Oil, gas and shipping industries are seriously affected.

COPPER AND COPPER-CONTAINING PESTICIDES: METABOLISM, TOXICITY AND OXIDATIVE STRESS

Directory of Open Access Journals (Sweden)

Viktor Husak

2015-05-01

Full Text Available The purpose of this paper is to provide a brief review of the current knowledge regarding metabolism and toxicity of copper and copper-based pesticides in living organisms. Copper is an essential trace element in all living organisms (bacteria, fungi, plants, and animals, because it participates in different metabolic processes and maintain functions of organisms. The transport and metabolism of copper in living organisms is currently the subject of many studies. Copper is absorbed, transported, distributed, stored, and excreted in the body via the complex of homeostatic processes, which provide organisms with a needed constant level of this micronutrient and avoid excessive amounts. Many aspects of copper homeostasis were studied at the molecular level. Copper based-pesticides, in particularly fungicides, bacteriocides and herbicides, are widely used in agricultural practice throughout the world. Copper is an integral part of antioxidant enzymes, particularly copper-zinc superoxide dismutase (Cu,Zn-SOD, and plays prominent roles in iron homeostasis. On the other hand, excess of copper in organism has deleterious effect, because it stimulates free radical production in the cell, induces lipid peroxidation, and disturbs the total antioxidant capacity of the body. The mechanisms of copper toxicity are discussed in this review also.

Uptake and internalisation of copper by three marine microalgae: comparison of copper-sensitive and copper-tolerant species.

Science.gov (United States)

Levy, Jacqueline L; Angel, Brad M; Stauber, Jennifer L; Poon, Wing L; Simpson, Stuart L; Cheng, Shuk Han; Jolley, Dianne F

2008-08-29

Although it has been well established that different species of marine algae have different sensitivities to metals, our understanding of the physiological and biochemical basis for these differences is limited. This study investigated copper adsorption and internalisation in three algal species with differing sensitivities to copper. The diatom Phaeodactylum tricornutum was particularly sensitive to copper, with a 72-h IC50 (concentration of copper to inhibit growth rate by 50%) of 8.0 microg Cu L(-1), compared to the green algae Tetraselmis sp. (72-h IC50 47 microg Cu L(-1)) and Dunaliella tertiolecta (72-h IC50 530 microg Cu L(-1)). At these IC50 concentrations, Tetraselmis sp. had much higher intracellular copper (1.97+/-0.01 x 10(-13)g Cu cell(-1)) than P. tricornutum (0.23+/-0.19 x 10(-13)g Cu cell(-1)) and D. tertiolecta (0.59+/-0.05 x 10(-13)g Cu cell(-1)), suggesting that Tetraselmis sp. effectively detoxifies copper within the cell. By contrast, at the same external copper concentration (50 microg L(-1)), D. tertiolecta appears to better exclude copper than Tetraselmis sp. by having a slower copper internalisation rate and lower internal copper concentrations at equivalent extracellular concentrations. The results suggest that the use of internal copper concentrations and net uptake rates alone cannot explain differences in species-sensitivity for different algal species. Model prediction of copper toxicity to marine biota and understanding fundamental differences in species-sensitivity will require, not just an understanding of water quality parameters and copper-cell binding, but also further knowledge of cellular detoxification mechanisms.

Unintended consequences of atmospheric injection of sulphate aerosols.

Energy Technology Data Exchange (ETDEWEB)

Brady, Patrick Vane; Kobos, Peter Holmes; Goldstein, Barry

2010-10-01

Most climate scientists believe that climate geoengineering is best considered as a potential complement to the mitigation of CO{sub 2} emissions, rather than as an alternative to it. Strong mitigation could achieve the equivalent of up to -4Wm{sup -2} radiative forcing on the century timescale, relative to a worst case scenario for rising CO{sub 2}. However, to tackle the remaining 3Wm{sup -2}, which are likely even in a best case scenario of strongly mitigated CO{sub 2} releases, a number of geoengineering options show promise. Injecting stratospheric aerosols is one of the least expensive and, potentially, most effective approaches and for that reason an examination of the possible unintended consequences of the implementation of atmospheric injections of sulphate aerosols was made. Chief among these are: reductions in rainfall, slowing of atmospheric ozone rebound, and differential changes in weather patterns. At the same time, there will be an increase in plant productivity. Lastly, because atmospheric sulphate injection would not mitigate ocean acidification, another side effect of fossil fuel burning, it would provide only a partial solution. Future research should aim at ameliorating the possible negative unintended consequences of atmospheric injections of sulphate injection. This might include modeling the optimum rate and particle type and size of aerosol injection, as well as the latitudinal, longitudinal and altitude of injection sites, to balance radiative forcing to decrease negative regional impacts. Similarly, future research might include modeling the optimum rate of decrease and location of injection sites to be closed to reduce or slow rapid warming upon aerosol injection cessation. A fruitful area for future research might be system modeling to enhance the possible positive increases in agricultural productivity. All such modeling must be supported by data collection and laboratory and field testing to enable iterative modeling to increase the

Biotic conversion of sulphate to sulphide and abiotic conversion of sulphide to sulphur in a microbial fuel cell using cobalt oxide octahedrons as cathode catalyst.

Science.gov (United States)

Chatterjee, Pritha; Ghangrekar, M M; Rao, Surampalli; Kumar, Senthil

2017-05-01

Varying chemical oxygen demand (COD) and sulphate concentrations in substrate were used to determine reaction kinetics and mass balance of organic matter and sulphate transformation in a microbial fuel cell (MFC). MFC with anodic chamber volume of 1 L, fed with wastewater having COD of 500 mg/L and sulphate of 200 mg/L, could harvest power of 54.4 mW/m 2 , at a Coulombic efficiency of 14%, with respective COD and sulphate removals of 90 and 95%. Sulphide concentration, even up to 1500 mg/L, did not inhibit anodic biochemical reactions, due to instantaneous abiotic oxidation to sulphur, at high inlet sulphate. Experiments on abiotic oxidation of sulphide to sulphur revealed maximum oxidation taking place at an anodic potential of -200 mV. More than 99% sulphate removal could be achieved in a MFC with inlet COD/sulphate of 0.75, giving around 1.33 kg/m 3  day COD removal. Bioelectrochemical conversion of sulphate facilitating sulphur recovery in a MFC makes it an interesting pollution abatement technique.

Accelerating the transit time of barium sulphate suspensions in small bowel examinations

International Nuclear Information System (INIS)

Summers, David S.; Roger, Mark D.; Allan, Paul L.; Murchison, John T.

2007-01-01

Purpose: To determine whether hyperosmolar and effervescent agents proven individually to accelerate transit time in the barium small bowel examination have an additive effect when combined, surpassing that of either agent alone. Materials and methods: One hundred and forty-nine patients were randomised to four groups. Three hundred milliliters of barium sulphate alone was given to the first group. Fifteen milliliters of iodinated hyperosmolar contrast agent (Gastrografin, meglumine/sodium diatrizoate, Schering) was given in addition to barium sulphate to the second group while six packets of effervescent granules (Carbex, Ferring) were added for the third group. The final group was given a combination of both additives and barium sulphate. The time taken following ingestion for the contrast column to reach the caecum, as assessed by frequent interval fluoroscopy, was recorded. A subgroup of 32 patients were selected randomly from the four groups, 8 from each and assessed for quality of examination. Statistical assessments were made using Kruskal-Wallis and Mann-Whitney tests. Results: One hundred and nineteen patients were analysed after exclusions. The addition of accelerant to barium sulphate, both individually and in combination significantly reduced the small bowel transit time (p < 0.001). No significant difference existed between the additives when used with barium alone. The combined group had significantly faster transit times compared to the hyperosmolar group (p = 0.02). Differences between combined and effervescent groups tended towards significance (p = 0.09). No significant difference existed between groups when examination quality was assessed. Conclusion: These results suggest that the addition of combined effervescent and hyperosmolar agents to the barium suspension may significantly shorten the small bowel transit time without adversely affecting examination quality. This has implications for patient acceptability of the examination as well as

The Effect of Copper on the Color of Shrimps: Redder Is Not Always Healthier

Science.gov (United States)

Martínez, Ana; Romero, Yanet; Castillo, Tania; Mascaró, Maite; López-Rull, Isabel; Simões, Nuno; Arcega-Cabrera, Flor; Gaxiola, Gabriela; Barbosa, Andrés

2014-01-01

The objective of this research is to test the effects of copper on the color of pacific white shrimp (Litopenaeus vannamei) in vivo. Forty-eight shrimps (L. vannamei) were exposed to a low concentration of copper (1 mg/L; experimental treatment) and forty-eight shrimps were used as controls (no copper added to the water). As a result of this experiment, it was found that shrimps with more copper are significantly redder than those designated as controls (hue (500–700 nm): P = 0.0015; red chroma (625–700 nm): P<0.0001). These results indicate that redder color may result from exposure to copper and challenge the commonly held view that highly pigmented shrimps are healthier than pale shrimps. PMID:25229639

Study of Factors Influencing Oxygen-18 Isotopic Contents of Dissolved Sulphate in the Shallow Groundwater In Karawang Area

International Nuclear Information System (INIS)

Ristin Pujiindiyati, E.; Bungkus Pratikno

2010-01-01

The study was conducted to investigate the factors influencing oxygen-18 isotopic contents of dissolved sulphate in shallow groundwater from Karawang area. The δ 18 O is a relative abundance of O-18 compared to O-16 in CO 2 gas. CO 2 gas was released from the equilibrium between water samples and CO 2 gas, and from the reduction of sulphate samples with graphite. From this investigation, the δ 18 O (H 2 O) values were in the range of -3.21 0 / 00 to 6.25 0 / 00 whereas the δ 18 O (SO 4 2- ) values were 9.64 0 / 00 to 20.72 0 / 00 . The wide variation of δ 18 O (SO 4 2- ) values might be result due to inhomogeneity of sulphate sources in groundwater where the groundwater sulphates were generally derived from the dissolution of marine evaporites rocks. The groundwaters and Citarum River near waters to Johar site showed lowering of δ 18 O (SO 4 2- ) values. It might be related to the present of the traditional market in this location. The lowering of these values might be due to the increase of the sulphate reduction process caused by anaerobic bacteria growth in organic garbage deposition. Plotting between δ 18 O (SO 4 2- ) and δ 18 O (H 2 O) exhibited that the oxygen contribution from H 2 O to form sulphate was less than 25%. This indicated that the shallow groundwater in Karawang is located in a non-saturated zone and had a biotic condition. (author)

Phase Behavior and Rheology of Fatty Alcohol Sulphate, Fatty Alcohol Ether Sulphate from Palm based and Mixtures with other Surfactants

International Nuclear Information System (INIS)

Hong, L.K.; Nur Syazani Harun; Mohd Suzeren Mohd Jamil; Rahimi Mohd Yusop

2013-01-01

The phase diagrams of fatty alcohol sulphate (FAS)/ fatty alcohol ether sulphate (FAES)/ soap (4.5:4.5:1.0)/ propylene glycol/ water mixtures were established at 60 degree Celsius. The birefringence was observed under cross polarizers and their phases changes examined under a polarized microscope. The results showed that the liquid crystalline region for FAS and FAES occurred only in a small region. The optical patterns of lamellar liquid crystal were identified as oily streaks structure. The rheological tests of lamellar liquid crystal were carried out in the region of 4.5/ 4.5/ 1 FAES/ FAS/ soap with 0 % PG and 10 % of water. The rheological tests used were flow curve, 3 interval thixotropy test (3ITT), oscillation (dynamic test) stress sweep test and frequency sweep test measurement done using a cone-plate sensor (25 mm, 1 degree). The flow curve was fitted to a Casson model to obtain values for the consistency coefficient and the flow behavior index. The lamellar liquid crystal show typical flow behavior and stress influenced the recovery of the structure. Linear visco-elastic (LVE) range analysis show the critical stress value at 0.475%, and elastic modulus was dominant over an angular frequency range studied. (author)

In situ X-ray diffraction study of the electrochemical reaction on lead electrodes in sulphate electrolytes

International Nuclear Information System (INIS)

Angerer, P.; Mann, R.; Gavrilovic, A.; Nauer, G.E.

2009-01-01

The anodic oxidation of pure lead in two acidic sulphate electrolytes with identical ionic strength (pH ∼ 0 and pH ∼ -0.1) was studied by in situ grazing incidence X-ray diffraction method (GIXD). Crystalline products such as lead sulphate (anglesite, PbSO 4 , orthorhombic), α- and β-lead dioxide (α-PbO 2 , orthorhombic, and β-PbO 2 , tetragonal), and tribasic lead sulphate hydrate with the stoichiometric composition 3PbO.PbSO 4 .H 2 O (triclinic) were detected at defined potentials. A method for the semi-quantitative determination of the thickness of the deposited layer from diffraction data is described. After the in situ measurement, the washed and dried working electrodes were additionally characterized ex situ by GIXD measurements at different angles of incidence. The phase litharge (lead oxide, t-PbO, tetragonal) and lead sulphate were observed at the surface of the lead substrate. The quantitative evaluation of the diffraction intensity of this measurement series enables the modelling of a qualitative depth profile of the layer generated during the electrochemical treatment. The anglesite phase is located in the uppermost layer, while the litharge phase was detected closer to the lead substrate

Enhanced Soil Chemical Properties and Rice Yield in Acid Sulphate Soil by Application of Rice Straw

Directory of Open Access Journals (Sweden)

Siti Nurzakiah

2012-01-01

Full Text Available Swampland development such as acid sulphate soil for agricultural cultivation has various problem, including highsoil acidity, fluctuated and unpredictable water flooding and the presence of toxic elements such as Fe whichresulting in low crop yields. The research was conducted at the experimental station Belandean, Barito Kualaregency in dry season 2007. The objective of research was to study the effect of rice straw on the dynamic of soilpH, the concentration of iron and sulphate and yield on tidal land acid sulphate soil at two different water inletchannel. This research was designed in RCBD (Randomized Completely Block Design with five treatments (0, 2.5,5.0, 7.5 and 10 Mg ha-1 and four replications. Dolomite as much as 1 Mg ha-1 was also applied. This research wasdivided into two sub-units experiment i.e. two conditions of different water inlet channel. The first water channelswere placed with limestone and the second inlet was planted with Eleocharis dulcis. The results showed that (i ricestraw application did not affect the dynamic of soil pH, concentration of iron and sulphate, and (ii the highest yieldwas obtained with 7.5 Mg ha-1 of rice straw.

Electroactive biofilms of sulphate reducing bacteria

International Nuclear Information System (INIS)

Cordas, Cristina M.; Guerra, L. Tiago; Xavier, Catarina; Moura, Jose J.G.

2008-01-01

Biofilms formed from a pure strain of Desulfovibrio desulfuricans 27774 on stainless steel and graphite polarised surfaces were studied. The polarisation conditions applied were -0.4 V vs. SCE for different times. A cathodic current related with the biofilms growth was observed with a maximum intensity of -270 mA m -2 that remained stable for several days using graphite electrodes. These sulphate reducing bacteria biofilms present electrocatalytic activity towards hydrogen and oxygen reduction reactions. Electrode polarisation has a selective effect on the catalytic activity. The biofilms were also observed by scanning electronic microscopy revealing the formation of homogeneous films on the surfaces

Extraction of nickel from Ramu laterite by sulphation roasting-water leaching

Science.gov (United States)

Wang, Weiwei; Du, Shangchao; Liu, Guo; Tang, Jianwen; Lu, Yeda; Lv, Dong

2017-08-01

Recovery of nickel from a PNG nickel laterite with high content of iron by a sulphation roasting-water leaching has been studied. The influences of sulfuric acid/ore ratio, temperature of roasting and water on recovery efficiency were investigated. The effective separation of nickel over the co-existed elements including iron was achieved by the process with mixing, curing, roasting and leaching stages. Near 100% of nickel was leached from the roasted laterite by water at 80°C in an atmospheric air, while co-leaching of about 2% of iron, under the optimal pre-treatment conditions with the ratio of acid: ore around 0.45:1 and the roasting temperature about 650°C. The advantages and disadvantages of sulphation atmospheric leaching are compared with pressure acid leaching with engineering consideration.

Crystallisation of mixtures of ammonium nitrate, ammonium sulphate and soot

NARCIS (Netherlands)

Dougle, P.G.; Veefkind, J.P.; Brink, H.M. ten

1998-01-01

Crystallisation of laboratory aerosols of ammonium nitrate and of internal mixtures of this salt with ammonium sulphate were investigated using humidity controlled nephelometry. The aerosol was produced via nebulizing of solutions and then dried to 25% RH, which is a realistic minimum value for

Utilization of Copper Alloys for Marine Applications

Science.gov (United States)

Drach, Andrew

Utilization of copper alloy components in systems deployed in marine environment presents potential improvements by reducing maintenance costs, prolonging service life, and increasing reliability. However, integration of these materials faces technological challenges, which are discussed and addressed in this work, including characterization of material performance in seawater environment, hydrodynamics of copper alloy components, and design procedures for systems with copper alloys. To characterize the hydrodynamic behavior of copper alloy nets, mesh geometry of the major types of copper nets currently used in the marine aquaculture are analyzed and formulae for the solidity and strand length are proposed. Experimental studies of drag forces on copper alloy net panels are described. Based on these studies, empirical values for normal drag coefficients are proposed for various types of copper netting. These findings are compared to the previously published data on polymer nets. It is shown that copper nets exhibit significantly lower resistance to normal currents, which corresponds to lower values of normal drag coefficient. The seawater performance (corrosion and biofouling) of copper alloys is studied through the field trials of tensioned and untensioned specimens in a one-year deployment in the North Atlantic Ocean. The corrosion behavior is characterized by weight loss, optical microscopy, and SEM/EDX analyses. The biofouling performance is quantified in terms of the biomass accumulation. To estimate the effects of stray electrical currents on the seawater corrosion measurements, a low cost three-axis stray electric current monitoring device is designed and tested both in the lab and in the 30-day field deployment. The system consists of a remotely operated PC with a set of pseudo-electrodes and a digital compass. The collected data is processed to determine magnitudes of AC and DC components of electric field and dominant AC frequencies. Mechanical behavior of

Bacterial sulphate reduction and the development of alklinity. III. Experiments under natural conditions in the Wadi Natrun

Energy Technology Data Exchange (ETDEWEB)

Abd-El-Malek, Y; Rizk, S G

1963-01-01

Evidence that microbial sulphate reduction is mainly responsible for the formation of the natron (hydrated Na/sub 2/CO/sub 3/) deposits in Wadi Natrun is presented. The sulphate in the infiltrating water is reduced during passage through the surrounding waterlogged soil and the bicarbonate formed is later concentrated by evaporation in the lakes.

Corrosion behaviour of a stream generator tube material in simulated steam generator feedwater containing chlorides and sulphates

Energy Technology Data Exchange (ETDEWEB)

Bojinov, M.; Kinnunen, P.; Laitinen, T.; Maekelae, K.; Saario, T.; Sirkiae, P.; Yliniemi, K. [VTT Manufacturing Technology, Espoo (Finland); Buddas, T.; Halin, M.; Tompuri, K. [Fortum Power and Heat Oy, Loviisa Power Plant (Finland)

2002-07-01

The goal of the present work has been to assess the effect of relatively high concentrations of anionic impurities (Cl{sup -}, SO{sub 4}{sup 2-}) on the corrosion behaviour of Ti-stabilised stainless steel SG tubes in simulated steam generator feed-water. The main observations of this work can be summarised as follows: Sulphate ions seem to be more aggressive than chloride ions towards the primary passive film on 08X18H10T stainless steel. The results may indicate that it is more important to have a low concentration of sulphate ions than of chloride ions in secondary side water when the effects of chemical conditions on tube degradation are considered. The presence of chloride ions seems to weaken the detrimental effect of sulphate ions on the stability of oxide films growing on 08X18H10T stainless steel. No localised corrosion features of 08X18H10T stainless steel were detected in the voltammetric and impedance measurements in solutions containing up to 5000 ppb sulphates, chlorides or both of the anions. (authors)

Corrosion behaviour of a stream generator tube material in simulated steam generator feedwater containing chlorides and sulphates

International Nuclear Information System (INIS)

Bojinov, M.; Kinnunen, P.; Laitinen, T.; Maekelae, K.; Saario, T.; Sirkiae, P.; Yliniemi, K.; Buddas, T.; Halin, M.; Tompuri, K.

2002-01-01

The goal of the present work has been to assess the effect of relatively high concentrations of anionic impurities (Cl - , SO 4 2- ) on the corrosion behaviour of Ti-stabilised stainless steel SG tubes in simulated steam generator feed-water. The main observations of this work can be summarised as follows: Sulphate ions seem to be more aggressive than chloride ions towards the primary passive film on 08X18H10T stainless steel. The results may indicate that it is more important to have a low concentration of sulphate ions than of chloride ions in secondary side water when the effects of chemical conditions on tube degradation are considered. The presence of chloride ions seems to weaken the detrimental effect of sulphate ions on the stability of oxide films growing on 08X18H10T stainless steel. No localised corrosion features of 08X18H10T stainless steel were detected in the voltammetric and impedance measurements in solutions containing up to 5000 ppb sulphates, chlorides or both of the anions. (authors)

Diagnosis of Hunter's syndrome carriers; radioactive sulphate incorporation into fibroblasts in the presence of fructose 1-phosphate

International Nuclear Information System (INIS)

Toennesen, T.; Lykkelund, C.; Guettler, F.

1982-01-01

Mutual correction of co-cultivated fibroblasts from patients with Hunter's and Hurler's syndrome could be inhibited by either fructose 1-phosphate or mannose 6-phosphate. In the presence of fructose 1-phosphate a 50% mixture of fibroblasts from a patient with Hunter's syndrome and a normal homozygous individual showed an increased 35 S-sulphate incorporation into acid mucopolysaccharides. When fibroblast cultures from one obligate and two possible carriers of Hunter's syndrome were tested for 35 S-sulphate incorporation, the cultures showed either twice the normal 35 S-sulphate incorporation into acid mucopolysaccharides in the presence of fructose 1-phosphate or an abnormally high incorporation in the presence as well as in the absence of the sugar phosphate. (orig.)

The role of cysteine residues in the sulphate transporter, SHST1: construction of a functional cysteine-less transporter.

Science.gov (United States)

Howitt, Susan M

2005-05-20

We investigated the role of cysteine residues in the sulphate transporter, SHST1, with the aim of generating a functional cysteine-less variant. SHST1 contains five cysteine residues and none was essential for function. However, replacement of C421 resulted in a reduction in transport activity. Sulphate transport by C205 mutants was dependent on the size of the residue at this position. Alanine at position 205 resulted in a complete loss of function whereas leucine resulted in a 3-fold increase in sulphate transport relative to wild type SHST1. C205 is located in a putative intracellular loop and our results suggest that this loop may be important for sulphate transport. By replacing C205 with leucine and the other four cysteine residues with alanine, we constructed a cysteine-less variant of SHST1 that has transport characteristics indistinguishable from wild type. This construct will be useful for further structure and function studies of SHST1.

Kinetic and Thermodynamic Studies on Adsorption of Sulphate from ...

African Journals Online (AJOL)

DELL USER

22, No. 1, 2017. 39. Kinetic and Thermodynamic Studies on Adsorption of Sulphate from Aqueous Solution by. Magnetite ... poison catalysts, and affect the .... C for 1 h in a stainless steel reactor placed in a furnace ... N2 gas for 30 min. 50 ml of ...... adsorption for designing and evaluating the ... is the equilibrium liquid-phase.

Long-term effects of operating temperature and sulphate addition on the methanogenic community structure of anaerobic hybrid reactors.

Science.gov (United States)

Pender, Seán; Toomey, Margaret; Carton, Micheál; Eardly, Dónal; Patching, John W; Colleran, Emer; O'Flaherty, Vincent

2004-02-01

The diversity, population dynamics, and activity profiles of methanogens in anaerobic granular sludges from two anaerobic hybrid reactors treating a molasses wastewater both mesophilically (37 degrees C) and thermophilically (55 degrees C) during a 1081 day trial were determined. The influent to one of the reactors was supplemented with sulphate, after an acclimation period of 112 days, to determine the effect of competition with sulphate-reducing bacteria on the methanogenic community structure. Sludge samples were removed from the reactors at intervals throughout the operational period and examined by amplified ribosomal DNA (rDNA) restriction analysis (ARDRA) and partial sequencing of 16S rRNA genes. In total, 18 operational taxonomic units (OTUs) were identified, 12 of which were sequenced. The methanogenic communities in both reactors changed during the operational period. The seed sludge and the reactor biomass sampled during mesophilic operation, both in the presence and absence of sulphate, was characterised by a predominance of Methanosaeta spp. Following temperature elevation, the dominant methanogenic sequences detected in the non-sulphate supplemented reactor were closely related to Methanocorpusculum parvum. By contrast, the dominant OTUs detected in the sulphate-supplemented reactor upon temperature increase were related to the hydrogen-utilising methanogen, Methanobacterium thermoautotrophicum. The observed methanogenic community structure in the reactors correlated with the operational performance of the reactors during the trial and with physiological measurements of the reactor biomass. Both reactors achieved chemical oxygen demand (COD) removal efficiencies of over 90% during mesophilic operation, with or without sulphate supplementation. During thermophilic operation, the presence of sulphate resulted in decreased reactor performance (effluent acetate concentrations of >3000 mg/l and biogas methane content of acetate at 55 degrees C was

Magnesium sulphate as a safe treatment for persistent pulmonary hypertension of newborn resistant to mechanical hyperventilation

International Nuclear Information System (INIS)

Dehdashtian, M.; Tebatebae, K.

2007-01-01

To see the effects of magnesium sulphate in newborn with persistent pulmonary hypertension of newborn (PPHN) who did not respond to mechanical hyperventilation and are candidate for Extra Corporeal Membrane Oxygenation (ECMO). Ten newborn who were admitted to Neonatal Intensive Care Unit (NICU) with profound hypoxia and respiratory failure due to PPHN were treated with conventional mechanical ventilation and then mechanical hyperventilation. The newborns who did not respond to mechanical Hyperventilation were treated with magnesium sulphate infusion. Nine out of ten babies survived and one of them died. The differences between the mean AaDo2, OI index, and PH after mechanical hyperventilation and magnesium sulphate administration was significant. Magnesium has a role in the treatment of PPHN patients who do not respond to hyperventilation or may be applied instead of hyperventilation. (author)

Transcriptome response to copper heavy metal stress in hard-shelled mussel (Mytilus coruscus

Directory of Open Access Journals (Sweden)

Meiying Xu

2016-03-01

Full Text Available The hard-shelled mussel (Mytilus coruscus has considerably one of the most economically important marine shellfish worldwide and considered as a good invertebrate model for ecotoxicity study for a long time. In the present study, we used Illumina sequencing technology (HiSeq2000 to sequence, assemble and annotate the transcriptome of the hard-shelled mussel which challenged with copper pollution. A total of 21,723,913 paired-end clean reads (NCBI SRA database SRX1411195 were generated from HiSeq2000 sequencer and 96,403 contigs (with N50 = 1118 bp were obtained after de novo assembling with Trinity software. Digital gene expression analysis reveals 1156 unigenes are upregulated and 1681 unigenes are downregulated when challenged with copper. By KEGG pathway enrichment analysis, we found that unigenes in four KEGG pathways (aminoacyl-tRNA biosynthesis, apoptosis, DNA replication and mismatch repair show significant differential expressed between control and copper treated groups. We hope that the gill transcriptome in copper treated hard-shelled mussel can give useful information to understand how mussel handles with heavy metal stress at molecular level. Keywords: Hard-shelled mussel, Heavy metal, Transcriptome, Ecotoxicity

Inhibition of bio corrosion of steel coupon by sulphate reducing ...

African Journals Online (AJOL)

SRB) and Iron oxidizing bacteria (IOB) using Aloe vera (Aloe barbadensis) extract was tested. The water sample revealed a heterotrophic bacterial count of 1.7x103 cfu/ml for the sulphate reducing bacteria and 4.1x103 cfu/ml for the Iron oxidizing ...

Sulphur and oxygen isotopic compositions of groundwater and sabkha - sulphate in the Middle East

International Nuclear Information System (INIS)

Robinson, B.W.

1987-01-01

The climate and topography of landward margins around the southern Mediterranean and the Arabian Gulf have given rise to areas of recent evaporite formation known as 'sabkhas'. These supratidal evaporitic flats have developed as a result of a relative fall in sea level after the last marine transgression (about 4000 years B.P.) which deposited carbonate sediments over coastal areas. Inland sabkhas may also develop in low lying areas and the desert 'soils' often have a 'getch' (duricrust) layer of gypsum or calcite near the surface. Published sulphur isotope studies of the sabkhas in the Gulf of Sirte (Libyan Arab Jamahiriya), Al Khiran (Kuwait) and Abu Dhabi (United Arab Emirates) indicate a sea water influence (δ 34 S ≅ +21 per mille; δ 18 O ≅ +10 per mille) only in the outer sabkha. At Al Khiran, Gulf of Sirte and Bardawil (Egypt) the δ 34 S values decrease to +14 per mille on the landward side. Continental sabkhas in the United Arab Emirates have δ 34 S values between +13 and +16 per mille and the continental getch in Kuwait has δ 34 S=+15.6 per mille. Sulphate minerals from the Al Khiran sabkha have δ 34 S and δ 18 O values up to +17 and +16 per mille respectively, much lower than at Abu Dhabi, where sea water sulphate and bacterial activity are more prevalent. At Al Khiran the δ 34 S mineral values drop to +12 per mille and the spread is connected with mineral transformations. In the Libyan Arab Jamahiriya and the United Arab Emirates the continental sulphate was thought to be derived from Cretaceous sediments. However, in Kuwait, an aquiclude, the Rus Formation (L. Eocene), prevents older water and sulphate from entering the sabkhas. This widespread sulphate source with δ 34 S=+14 per mille may be derived from continental getch and surface evaporites which are transported and homogenized by dust storms. (author). 10 refs, 4 figs

Study on the influence of Sempervivum tectorum and Melatonin on Glutathion protective effects in rats blood exposed to Aluminum sulphate

Directory of Open Access Journals (Sweden)

Corina Gravila

2014-05-01

Full Text Available The present study was carried out to investigate the influence of Sempervivum tectorum aqueous extract and melatonin on reduced glutathione (GSH protective effect in Wistar albino rat blood exposed to aluminium sulphate- Al2(SO43. The rats were divided in one control group (C and 7 experimental groups (E. The control group received tap water. The experimental rats were feed the following way: E1 group – aluminum sulphate, daily, for 3 months; : E2 group – Sempervivum tectorum, daily, for 3 months; : E3 group – melatonin, daily, for 3 months; : E4 group – aluminum sulphate with Sempervivum tectorum, daily, for 3 months; : E5 group – aluminum sulphate with melatonin, daily, for 3 months; E6 group – aluminum sulphate, daily, for 3 months, and thereafter with Sempervivum tectorum for 1 month; E7 group – aluminum sulphate, daily, for 3 month, and thereafter with melatonin for 1 month. This study showed that Aluminum toxicity induced lower GSH. The oxidative stress caused by aluminum, given individual, is more pronounced than in the case in which aluminum is administered simultaneously with Sempervivum tectorum or melatonin. Decreasing GSH value is very small if Sempervivum tectorum or melatonin is given for one month, three months after the administration of aluminum. Effect induced by melatonin is more favorable than that of Sempervivum tectorum.

New Sulphated Flavonoids from Tamarix africana and Biological Activities of Its Polar Extract.

Science.gov (United States)

Karker, Manel; De Tommasi, Nunziatina; Smaoui, Abderrazak; Abdelly, Chedly; Ksouri, Riadh; Braca, Alessandra

2016-10-01

The phytochemical investigation of Tamarix africana Poir. (Tamaricaceae) shoot polar extract afforded three new sulphated flavonoids, (2 S ,4 R )-5,7,4'-trihydroxyflavan-4-ol 5,7-disulphate ( 1 ), (2 S )-5,7,4'-trihydroxyflavan 7- O -sulphate ( 2 ), and (2 S )-naringenin 4'- O -sulphate ( 3 ), together with ten known compounds. Their structures were determined by spectroscopic methods including 1D and 2D NMR analysis and HRMS. Biological activities of the polar extract of T. africana shoots related to its phenolic content were also investigated. A high total phenolic content (151.1 mg GAE/g) was found in the methanol shoot extract, which exhibits strong antioxidant activities using the oxygen radical absorbance capacity method and a skin cell-based assay. Moreover, the shoot extract showed significant anti-inflammatory activity, reducing nitric oxide release by 53.5 % at 160 µg/mL in lipopolysaccharide-stimulated RAW 264.7 macrophages. Finally, T. africana shoot extract inhibited the growth of A-549 lung carcinoma cells, with an IC 50 value of 34 µg/mL. Georg Thieme Verlag KG Stuttgart · New York.

Isolation and characterization of copper tolerant bacterial isolates

International Nuclear Information System (INIS)

Farooq, S.; Shoeb, E.; Badar, U.; Akhtar, J.

2008-01-01

Twelve bacterial strains were isolated from metal contaminated sites close to the chemical factory, Purification and characterization of these strains was done. Maximum tolerable concentration (MTC) of all the isolated strains was determined against heavy metals cadmium chloride (CdCl/sub 2/), copper sulphate (CuSO/sub 4/), and nickel chloride (NiCI/sub 2/) and antibiotics kanamycin (Km), streptomycin (Sm), and chloramphenicol (Cm). Most promising strain was found to be GESSF012 which showed MTC of 4.5 mM and 1.6 mM against CdCI/sub 2/ in enriched and minimal media respectively; whereas MTC of 750 micro g/ml was against Sm. GESSF012 demonstrated the occurrence of multiple stress tolerance as this strain showed considerable tolerance against other heavy metals including CuSO/sub 4/, (3.0 mM in enriched media and 1.8 mM in minimal media) and NiCl/sub 2/, (2.0 mM in enriched media and 1.8 mM in minimal media) as well as other antibiotics Cm and Km (150 and 125 micro g/ml respectively). Plasmids were detected in most of the strains including GESSF012. (author)

Growth of micro-crystals in solution by in-situ heating via continuous wave infrared laser light and an absorber

Science.gov (United States)

Pathak, Shashank; Dharmadhikari, Jayashree A.; Thamizhavel, A.; Mathur, Deepak; Dharmadhikari, Aditya K.

2016-01-01

We report on growth of micro-crystals such as sodium chloride (NaCl), copper sulphate (CuSO4), potassium di-hydrogen phosphate (KDP) and glycine (NH2CH2COOH) in solution by in-situ heating using continuous wave Nd:YVO4 laser light. Crystals are grown by adding single walled carbon nanotubes (SWNT). The SWNTs absorb 1064 nm light and act as an in-situ heat source that vaporizes the solvent producing microcrystals. The temporal dynamics of micro-crystal growth is investigated by varying experimental parameters such as SWNT bundle size and incident laser power. We also report crystal growth without SWNT in an absorbing medium: copper sulphate in water. Even though the growth dynamics with SWNT and copper sulphate are significantly different, our results indicate that bubble formation is necessary for nucleation. Our simple method may open up new vistas for rapid growth of seed crystals especially for examining the crystallizability of inorganic and organic materials.

Electrical conduction in composites containing copper core-copper

Indian Academy of Sciences (India)

Composites of nanometre-sized copper core-copper oxide shell with diameters in the range 6.1 to 7.3 nm dispersed in a silica gel were synthesised by a technique comprising reduction followed by oxidation of a suitably chosen precursor gel. The hot pressed gel powders mixed with nanometre-sized copper particles ...

Patterned self-assembled monolayers of alkanethiols on copper nanomembranes by submerged laser ablation

Science.gov (United States)

Rhinow, Daniel; Hampp, Norbert A.

2012-06-01

Self-assembled monolayers (SAMs) of alkanethiols are major building blocks for nanotechnology. SAMs provide a functional interface between electrodes and biomolecules, which makes them attractive for biochip fabrication. Although gold has emerged as a standard, copper has several advantages, such as compatibility with semiconductors. However, as copper is easily oxidized in air, patterning SAMs on copper is a challenging task. In this work we demonstrate that submerged laser ablation (SLAB) is well-suited for this purpose, as thiols are exchanged in-situ, avoiding air exposition. Using different types of ω-substituted alkanethiols we show that alkanethiol SAMs on copper surfaces can be patterned using SLAB. The resulting patterns were analyzed by atomic force microscopy (AFM) and scanning electron microscopy (SEM). Both methods indicate that the intense laser beam promotes the exchange of thiols at the copper surface. Furthermore, we present a procedure for the production of free-standing copper nanomembranes, oxidation-protected by alkanethiol SAMs. Incubation of copper-coated mica in alkanethiol solutions leads to SAM formation on both surfaces of the copper film due to intercalation of the organic molecules. Corrosion-protected copper nanomembranes were floated onto water, transferred to electron microscopy grids, and subsequently analyzed by electron energy loss spectroscopy (EELS).

Preparation of Magnetite Nanocrystals from Ferrous Sulphate Solution

International Nuclear Information System (INIS)

Cho Yu Mon; Tint Tint Kywe; Moe Moe Kyaw

2010-12-01

Magnetite (Fe3O4) nanoparticle were prepared by hydrothermal process in two ways, which would be used for production of copier toner.In this investigation, the first process was made from ferrous sulphate (FeSO4 . 7H2O) by using 10 M sodium hydroxide solution. In this method, magnetite nanoparticles were prepared by changing aeration time from 1 to 3 hr and heated at 90C for 15 min. The alternative process was carried out from ferrous sulphate (FeSO4.7H2O) by using 6.6 M sodium hydroxide solution and sodium silicate solution.Magnetite (black iron oxide) was synthesized by using different aeration times and reaction times. Aeration time was changed from 1 to 2 hr and reaction time was changed from 1 to 5.5 hr at 85 C. The magnetites obtained were examined by X-ray Diffraction (XRD) analysis and Scanning Electron Microscopy (SEM) technique. The average particle size range of magnetite nanoprticles were 90-120 nm and 120-150 nm in each process. The maximum yied percentages of magnetite based on FeSO4 in both processing were found to be 46.30% and 60.72%. The precent yields of magnetite in both preparation based on theoretical yields were 91.02% and 94.83% respectively.

Effect of water hyacinth on distribution of sulphate-reducing bacteria ...

African Journals Online (AJOL)

The effect of the water hyacinth, Eichhornia crassipes (Mart.) Solms-Laub, on the distribution of populations of sulphate-reducing bacteria (SRB) in sediments from various stations on the shores of Lake Victoria around Mwanza Municipality, Tanzania, was studied. Lactate-utilising SRB were observed to be the dominant ...

Expeditious low-temperature sintering of copper nanoparticles with thin defective carbon shells

Science.gov (United States)

Kim, Changkyu; Lee, Gyoungja; Rhee, Changkyu; Lee, Minku

2015-04-01

The realization of air-stable nanoparticles, well-formulated nanoinks, and conductive patterns based on copper is a great challenge in low-cost and large-area flexible printed electronics. This work reports the synthesis of a conductively interconnected copper structure via thermal sintering of copper inks at a low temperature for a short period of time, with the help of thin defective carbon shells coated onto the copper nanoparticles. Air-stable copper/carbon core/shell nanoparticles (typical size ~23 nm, shell thickness ~1.0 nm) are prepared by means of an electric explosion of wires. Gaseous oxidation of the carbon shells with a defective structure occurs at 180 °C, impacting the choice of organic solvents as well as the sintering conditions to create a crucial neck formation. Isothermal oxidation and reduction treatment at 200 °C for only about 10 min yields an oxide-free copper network structure with an electrical resistivity of 25.1 μΩ cm (14.0 μΩ cm at 250 °C). Finally, conductive copper line patterns are achieved down to a 50 μm width with an excellent printing resolution (standard deviation ~4.0%) onto a polyimide substrate using screen printing of the optimized inks.The realization of air-stable nanoparticles, well-formulated nanoinks, and conductive patterns based on copper is a great challenge in low-cost and large-area flexible printed electronics. This work reports the synthesis of a conductively interconnected copper structure via thermal sintering of copper inks at a low temperature for a short period of time, with the help of thin defective carbon shells coated onto the copper nanoparticles. Air-stable copper/carbon core/shell nanoparticles (typical size ~23 nm, shell thickness ~1.0 nm) are prepared by means of an electric explosion of wires. Gaseous oxidation of the carbon shells with a defective structure occurs at 180 °C, impacting the choice of organic solvents as well as the sintering conditions to create a crucial neck formation

Investigation of the immobilisation/mobilisation of nickel, copper ...

African Journals Online (AJOL)

DRINIE

nitrate, manganese hydroxides, iron hydroxides, sulphate and carbon dioxide). ... standard solution contained (g·l-1 dH2O): ferrous ammonium sulphate, 39.21; ferric ... (AAS) with a nitrous oxide-acetylene flame, to minimise chemical interferences, was ... The synthetic refuse used facilitated the production of volatile fatty ...

Unusual pattern of leukoencephalopathy after morphine sulphate intoxication

Energy Technology Data Exchange (ETDEWEB)

Nanan, R.; Stockhausen, H.B. von; Petersen, B. [Children' s Hospital, University of Wuerzburg (Germany); Solymosi, L.; Warmuth-Metz, M. [Department for Neuroradiology, University of Wuerzburg (Germany)

2000-11-01

We report a 14-year-old girl with an unusual pattern of leukoencephalopathy after intentional intoxication with morphine sulphate tablets. Toxicological analysis showed exceedingly high levels of morphine and its metabolites. MRI disclosed a leukoencephalopathy with high signal from the centrum semiovale, corpus callosum and cerebellar white matter on T2-weighted images. These findings could be only partially explained by a hypoxic-ischaemic event; neurotoxic effects must be considered in this atypical leukoencephalopathy. (orig.)

Unusual pattern of leukoencephalopathy after morphine sulphate intoxication

International Nuclear Information System (INIS)

Nanan, R.; Stockhausen, H.B. von; Petersen, B.; Solymosi, L.; Warmuth-Metz, M.

2000-01-01

We report a 14-year-old girl with an unusual pattern of leukoencephalopathy after intentional intoxication with morphine sulphate tablets. Toxicological analysis showed exceedingly high levels of morphine and its metabolites. MRI disclosed a leukoencephalopathy with high signal from the centrum semiovale, corpus callosum and cerebellar white matter on T2-weighted images. These findings could be only partially explained by a hypoxic-ischaemic event; neurotoxic effects must be considered in this atypical leukoencephalopathy. (orig.)

Al-Fe interactions and growth enhancement in Melastoma malabathricum and Miscanthus sinensis dominating acid sulphate soils.

Science.gov (United States)

Watanabe, Toshihiro; Jansen, Steven; Osaki, Mitsuru

2006-12-01

Plants growing in acid sulphate soils are subject to high levels of Al availability, which may have effects on the growth and distribution of these species. Although Fe availability is also high in acid sulphate soils, little is known about the effect of Fe on the growth of native plants in these soils. Two species dominating this soil type in Asia, viz. Melastoma malabathricum and Miscanthus sinensis were grown hydroponically in a nutrient solution with different concentrations of Al and Fe. Melastoma malabathricum is found to be sensitive to Fe (40 and 100 microm). Application of 500 microm Al, however, completely ameliorates Fe toxicity and is associated with a decrease of Fe concentration in shoots and roots. The primary reason for the Al-induced growth enhancement of M. malabathricum is considered to be the Al-induced reduction of toxic Fe accumulation in roots and shoots. Therefore, Al is nearly essential for M. malabathricum when growing in acid sulphate soils. In contrast, application of both Fe and Al does not reduce the growth of M. sinensis, and Al application does not result in lower shoot concentrations of Fe, suggesting that this grass species has developed different mechanisms for adaptation to acid sulphate soils.

Reagent conditions of the flotation of copper, copper - molybdenum and copper -zinc ores in foreing countries

International Nuclear Information System (INIS)

Nevaeva, L.M.

1983-01-01

Reagents-collectors and frothers, used abroad in reagent regimes of flotation of copper, copper-molybdenum and copper zinc ores, have been considered. Xanthogenates, aerofloats, xanthogenformiates, thionocarbamates are mainly used as reagents-collectors. Methylizobutylcarbinol and Daufros are used as reagents-frothers

Biological sulphate reduction with primary sewage sludge in an ...

African Journals Online (AJOL)

2009-07-31

Jul 31, 2009 ... The success of the UASB reactor depends largely on the settling properties and stability of the sludge bed which comprises the anaerobic active biomass. The solid-liquid separation behaviour of the sludge bed in 2 UASB reactors (R1 at 35oC and. R2 at 20oC) fed with primary sewage sludge and sulphate ...

Biological sulphate reduction with primary sewage sludge in an ...

African Journals Online (AJOL)

The success of the UASB reactor depends largely on the settling properties and stability of the sludge bed which comprises the anaerobic active biomass. The solid-liquid separation behaviour of the sludge bed in 2 UASB reactors (R1 at 35oC and R2 at 20oC) fed with primary sewage sludge and sulphate was investigated ...

The influence of nickel sulphate on some physiological aspects of two cultivars of Raphanus sativus L.

Directory of Open Access Journals (Sweden)

Latif Helmy H.

2010-01-01

Full Text Available In this study two cultivars of radish Raphanus sativus cv. longipinnatus (white radish and Raphanus sativus cv. Cherry Belle (red radish were treated with different concentrations of nickel sulphate (0.0-50-100-150-200 ppm. The fresh and dry weight of shoots and roots, photosynthetic pigments, some antioxidant enzymes, total carbohydrates, total proteins and the SDS-PAGE protein profile of both cultivars were determined after 32 days. The results showed that increasing nickel sulphate concentrations decreased the fresh and dry weights of the shoots and roots, photosynthetic pigments, total carbohydrates and total protein in both cultivars. Higher concentrations of nickel sulphate increased the activity of catalase, peroxidase and polypenol oxidase. Electrophoresis banding profiles of proteins revealed qualitative and quantitative changes, and also the appearance or disappearance of some bands of the two cultivars. .

Electroactive biofilms of sulphate reducing bacteria

Energy Technology Data Exchange (ETDEWEB)

Cordas, Cristina M.; Guerra, L. Tiago; Xavier, Catarina [Requimte-CQFB, Departamento de Quimica, Faculdade de Ciencias e Tecnologia, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Moura, Jose J.G. [Requimte-CQFB, Departamento de Quimica, Faculdade de Ciencias e Tecnologia, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal)], E-mail: jose.moura@dq.fct.unl.pt

2008-12-01

Biofilms formed from a pure strain of Desulfovibrio desulfuricans 27774 on stainless steel and graphite polarised surfaces were studied. The polarisation conditions applied were -0.4 V vs. SCE for different times. A cathodic current related with the biofilms growth was observed with a maximum intensity of -270 mA m{sup -2} that remained stable for several days using graphite electrodes. These sulphate reducing bacteria biofilms present electrocatalytic activity towards hydrogen and oxygen reduction reactions. Electrode polarisation has a selective effect on the catalytic activity. The biofilms were also observed by scanning electronic microscopy revealing the formation of homogeneous films on the surfaces.

EFFECT OF PREEMPTIVE MAGNESIUM SULPHATE ON PAIN RELIEF AFTER LAPAROSCOPIC CHOLECYSTECTOMY

Directory of Open Access Journals (Sweden)

Ravi Vasupalli

2016-09-01

Full Text Available BACKGROUND The concept of preemptive analgesia was introduced by C. J. Woolf et al demonstrating that a post-injury hypersensitivity results via a central mechanism. The effect of magnesium on perioperative analgesic requirements was first evaluated by Koinig and his colleagues in patients with identical levels of surgical stimulation. Magnesium Sulphate is an antagonist of Nmethyl-D-aspartate (NMDA receptors and its associated channels and regulation of calcium influx into the cell. Magnesium causes modulation of acute pain reducing postsurgical pain intensity and dosage of analgesics. Seyhan et al have reported that magnesium sulphate boluses were effective for postoperative pain relief after gynaecological surgery. Fucs-Budder et al, Kussman B et al used continuous infusion (15 mg/kg/hr. in addition to initial bolus (50 mg/kg of magnesium sulphate in their studies, which caused bradycardia and delayed extubation time, which can be attributed to the infusion of Iva Bacak Kochman et al studied effect of low dose MgSO4 (7.5 mg/kg as analgesic agent after induction in patients undergoing laparoscopic cholecystectomy. This bolus dose of MgSO4 given for control of sympathetic response during intubation also reduced early postoperative pain. Study conducted by O Mentes et al on postoperative analgesic efficacy of single dose MgSO4 (50 mg/kg after laparoscopic cholecystectomy measured significantly less VAS scores. On this background, our study was done to evaluate the postoperative analgesic efficacy of single dose of magnesium sulphate (50 mg/kg as preemptive analgesic and measured after laparoscopic cholecystectomy. In addition to VAS scores, total tramadol consumption and time for first rescue analgesia, postoperative haemodynamic parameters and side effects if any were evaluated. METHODS After obtaining Institutional Ethical committee clearance and written informed consent from the patients, a randomised prospective study was conducted at King

Oral zinc sulphate in treatment of patients with thallium poisoning: A clinical therapeutic trial

Directory of Open Access Journals (Sweden)

Ahmed A. Al-Mohammadi

2011-06-01

Full Text Available Thallium poisoning is usually associated with typical dermatological features simulating that of zinc deficiency. The aim of this study was to evaluate the role of oral zinc sulphate in the treatment of patients with thallium poisoning.Materials and methods: This clinical therapeutic trial study was conducted in Departments of Dermatology of Baghdad and Basrah Teaching Hospitals from February 2008 - February 2010, where a total of 37 patients with thallium poisoning were enrolled.A detailed history was taken from all patients and complete clinical examination was performed. All patients received zinc sulphate in a dose of 5 mg/kg three times a day few days before confirming the diagnosis of thallium poisoning. Thallium in urine had been measured using the colorimetric method and was positive in all patients. After confirming the diagnosis of thallium poisoning, thallium antidotes Prussian blue was given to 32 patients.Results: Age range of 37 patients was 5-33 (24±5.3 years. The dermatological findings were mainly: anagen hair loss affected the scalp and limbs. Also, dusky ecchymotic red dermatitis like rash was observed on the face and dorsum of hands and legs, while neurological manifestations were mainly of peripheral neuropathy, were reported in 21 (55% patients. All patients but two responded promptly to a trial of zinc sulphate within few days.Conclusion: Oral Zinc sulphate appears to be an effective and safe treatment for thallium poisoning particularly for skin and hair features and in reducing its lethal progression and complications. J Clin Exp Invest 2011;2(2:133-7

Low-cost optical fabrication of flexible copper electrode via laser-induced reductive sintering and adhesive transfer

Science.gov (United States)

Back, Seunghyun; Kang, Bongchul

2018-02-01

Fabricating copper electrodes on heat-sensitive polymer films in air is highly challenging owing to the need of expensive copper nanoparticles, rapid oxidation of precursor during sintering, and limitation of sintering temperature to prevent the thermal damage of the polymer film. A laser-induced hybrid process of reductive sintering and adhesive transfer is demonstrated to cost-effectively fabricate copper electrode on a polyethylene film with a thermal resistance below 100 °C. A laser-induced reductive sintering process directly fabricates a high-conductive copper electrode onto a glass donor from copper oxide nanoparticle solution via photo-thermochemical reduction and agglomeration of copper oxide nanoparticles. The sintered copper patterns were transferred in parallel to a heat-sensitive polyethylene film through self-selective surface adhesion of the film, which was generated by the selective laser absorption of the copper pattern. The method reported here could become one of the most important manufacturing technologies for fabricating low-cost wearable and disposable electronics.

The microbial communities and potential greenhouse gas production in boreal acid sulphate, non-acid sulphate, and reedy sulphidic soils

Energy Technology Data Exchange (ETDEWEB)

Šimek, Miloslav, E-mail: misim@upb.cas.cz [Biology Centre AS CR, v. v. i., Institute of Soil Biology, 370 05 České Budějovice (Czech Republic); University of South Bohemia, Faculty of Science, 370 05 České Budějovice (Czech Republic); Virtanen, Seija; Simojoki, Asko [Department of Food and Environmental Sciences, University of Helsinki, FI-00014 Helsinki (Finland); Chroňáková, Alica; Elhottová, Dana; Krištůfek, Václav [Biology Centre AS CR, v. v. i., Institute of Soil Biology, 370 05 České Budějovice (Czech Republic); Yli-Halla, Markku [Department of Food and Environmental Sciences, University of Helsinki, FI-00014 Helsinki (Finland)

2014-01-01

Acid sulphate (AS) soils along the Baltic coasts contain significant amounts of organic carbon and nitrogen in their subsoils. The abundance, composition, and activity of microbial communities throughout the AS soil profile were analysed. The data from a drained AS soil were compared with those from a drained non-AS soil and a pristine wetland soil from the same region. Moreover, the potential production of methane, carbon dioxide, and nitrous oxide from the soils was determined under laboratory conditions. Direct microscopic counting, glucose-induced respiration (GIR), whole cell hybridisation, and extended phospholipid fatty acid (PLFA) analysis confirmed the presence of abundant microbial communities in the topsoil and also in the deepest Cg2 horizon of the AS soil. The patterns of microbial counts, biomass and activity in the profile of the AS soil and partly also in the non-AS soil therefore differed from the general tendency of gradual decreases in soil profiles. High respiration in the deepest Cg2 horizon of the AS soil (5.66 μg C g{sup − 1} h{sup − 1}, as compared to 2.71 μg C g{sup − 1} h{sup − 1} in a top Ap horizon) is unusual but reasonable given the large amount of organic carbon in this horizon. Nitrous oxide production peaked in the BCgc horizon of the AS and in the BC horizon of the non-AS soil, but the peak value was ten-fold higher in the AS soil than in the non-AS soil (82.3 vs. 8.6 ng N g{sup − 1}d{sup − 1}). The data suggest that boreal AS soils on the Baltic coast contain high microbial abundance and activity. This, together with the abundant carbon and total and mineral nitrogen in the deep layers of AS soils, may result in substantial gas production. Consequently, high GHG emissions could occur, for example, when the generally high water table is lowered because of arable farming. - Highlights: •Boreal acid sulphate soils contain large amounts of organic C and N in subsoils. •Microbial communities throughout the acid

Spatial and temporal changes in sulphate-reducing groundwater bacterial community structure in response to Managed Aquifer Recharge.

Science.gov (United States)

Reed, D A; Toze, S; Chang, B

2008-01-01

The population dynamics of bacterial able to be cultured under sulphate reducing condition was studied in conjunction with changes in aquifer geochemistry using multivariate statistics for two contrasting Managed Aquifer Recharge (MAR) techniques at two different geographical locations (Perth, Western Australia and Adelaide, South Australia). Principal component analysis (PCA) was used to investigate spatial and temporal changes in the overall chemical signature of the aquifers using an array of chemical analytes which demonstrated a migrating geochemical plume. Denaturing Gradient Gel Electrophoresis (DGGE) using DNA from sulphate-reducing bacteria cultures was used to detect spatial and temporal changes in population dynamics. Bacterial and geochemical evidence suggested that groundwater at greatest distance from the nutrient source was least affected by treated effluent recharge. The results suggested that bacterial populations that were able to be cultured in sulphate reducing media responded to the migrating chemical gradient and to the changes in aquifer geochemistry. Most noticeably, sulphate-reducing bacterial populations associated with the infiltration galleries were stable in community structure over time. Additionally, the biodiversity of these culturable bacteria was restored when aquifer geochemistry returned to ambient conditions during the recovery phase at the Adelaide Aquifer Storage and Recovery site. Copyright CSIRO 2008.

The impact of acid sulphate soils on water bodies and fish deaths in Finland; Happamien sulfaattimaiden aiheuttamat vesistoevaikutukset ja kalakuolemat Suomessa

Energy Technology Data Exchange (ETDEWEB)

Sutela, T.; Vuori, K.-M.; Louhi, P. [and others

2012-05-15

We have compiled in this review a comprehensive presentation of the impacts of acid sulphate soils (ASS) on water quality, biota, and fish kills in Finnish water bodies. This review is a result of extensive collaboration among research scientists in connection with the CATERMASS project co-ordinated by the Finnish Environment Institute (SYKE). Acid sulphate soils were formed in the eutrophic coastal waters of the Baltic Sea 4,000-8,000 years ago as microbes reduced the sulphate contained in saline seawater into sulphide. Sulphide clay soils emerging through land uplift have since been reclaimed and drained for cultivation use. Sulphur released in the resultant oxidation process reacted with soil water to form sulphuric acid, which draws toxic metals such as aluminium, cadmium, and copper from the soil. Heavy rains and the waters of springtime thawing transported acids and metals to the water bodies. In recent decades, the drainage depth of fields has increased because of the growing popularity of subterranean drainage methods, thus exacerbating the adverse ASS impacts on water bodies. Acidity and the attendant proliferation of toxic forms of metals induce changes in all organism groups of water biota, among them fish, macroinvertebrates, macrophytes, and bottom algae. On the specimen level, malformations have been discovered, such as structural pupae impairment in aquatic insects. The defence mechanism employed by fish against harmful substances in the surrounding water is to increase mucus exudation in the gills, which results in reduced respiration function. Exposure to acidity and metals harms the reproduction cycle of fish by delaying the development of follicles into mature eggs and by hindering eggs' fertilisation and embryo development. On the biota level, the manifestation of ASS impact is often the absence of the species or species groups most vulnerable to acidity. The species of river fish that are vulnerable to acidity include, for example

Sources of sulphate minerals in limestone cave-a possible evidence of anthropogenic activity: a case study in Črna Jama Cave (Slovenia).

Science.gov (United States)

Jarc, Simona; Miler, Miloš; Šebela, Stanka; Zupančič, Nina

2017-12-01

In the caves, the formation of cave minerals is a consequence of a variety of chemical reactions, some of them also due to human activity. There are many caves in Slovenia, but sulphate minerals are not very often reported and analysed. In this study, the presence of sulphate minerals is detected by SEM/EDS analysis of speleothems from Črna Jama, a cave near Kočevje (southern Slovenia). The cave is characterised by its dark, almost black colour on cave walls, floor and speleothems. Anthropogenic influence in the cave is still visible, including the remains of a fireplace, some inscriptions on the walls and wooden containers. The analyses of some of the black-coated speleothems reveal the presence of calcium sulphate, confirmed by XRD as gypsum. Gypsum crystals are around 50 μm in size, and they occur in thin crusts. Additionally, some rare authigenic baryte crystals a few micrometres in size are detected. The sulphates δ 34 S value in gypsum found on dark coloured speleothems is + 10.4‰ Vienna Canyon Diablo Troilite (VCDT), while the sulphate δ 34 S of the bedrock is + 8.6‰ VCDT. The more likely source of sulphate ions is thus biomass burning rather than bedrock. Also, bedrock and biomass ash are a very probable source of calcium and barium. The highly probable pyrogenous origin of sulphates draws attention to human impact on cave mineralogy.

Bone mineralization in newborns whose mothers received magnesium sulphate for tocolysis of premature labour

International Nuclear Information System (INIS)

Malaeb, Shadi N.; Rassi, Adriana I.; Yunis, Khalid A.; Haddad, Maurice C.; Seoud, Muhieddine A.

2004-01-01

Prolonged maternal magnesium sulphate infusion therapy for tocolysis of premature labour may result in secondary fetal hypermagnesaemia, which has been associated with bony abnormalities in the newborn. We report on four infants, members of two twin pregnancies, who were exposed to prolonged fetal hypermagnesaemia. Three of the infants, all appropriate for gestational age, showed abnormal radiological findings consisting of abnormal mineralisation of long-bone metaphyses owing to fetal hypermagnesaemia. The fourth infant, who was growth retarded, had normal bones. Intrauterine growth restriction appears to be protective against magnesium sulphate-induced abnormal bone mineralisation in the newborn. (orig.)

Bone mineralization in newborns whose mothers received magnesium sulphate for tocolysis of premature labour

Energy Technology Data Exchange (ETDEWEB)

Malaeb, Shadi N.; Rassi, Adriana I.; Yunis, Khalid A. [Department of Pediatrics, American University of Beirut Medical Center, PO Box 11-0236, Beirut (Lebanon); Haddad, Maurice C. [Department of Diagnostic Radiology, American University of Beirut Medical Center, Beirut (Lebanon); Seoud, Muhieddine A. [Department of Obstetrics and Gynecology, American University of Beirut Medical Center, Beirut (Lebanon)

2004-05-01

Prolonged maternal magnesium sulphate infusion therapy for tocolysis of premature labour may result in secondary fetal hypermagnesaemia, which has been associated with bony abnormalities in the newborn. We report on four infants, members of two twin pregnancies, who were exposed to prolonged fetal hypermagnesaemia. Three of the infants, all appropriate for gestational age, showed abnormal radiological findings consisting of abnormal mineralisation of long-bone metaphyses owing to fetal hypermagnesaemia. The fourth infant, who was growth retarded, had normal bones. Intrauterine growth restriction appears to be protective against magnesium sulphate-induced abnormal bone mineralisation in the newborn. (orig.)

Mercury methylation in high and low-sulphate impacted wetland ponds within the prairie pothole region of North America

International Nuclear Information System (INIS)

Hoggarth, Cameron G.J.; Hall, Britt D.; Mitchell, Carl P.J.

2015-01-01

Using enriched stable 201 Hg injections into intact sediment cores, we provide the first reported Hg methylation potential rate constants (k m ) in prairie wetland ponds (0.016–0.17 d −1 ). Our k m values were similar to other freshwater wetlands and did not differ in ponds categorized with high compared to low surface water concentrations of sulphate. Sites with high sulphate had higher proportions of methylmercury (MeHg) in sediment (2.9 ± 1.6% vs. 1.0 ± 0.3%) and higher surface water MeHg concentrations (1.96 ± 1.90 ng L −1 vs. 0.56 ± 0.55 ng L −1 ). Sediment-porewater partitioning coefficients were small, and likely due to high ionic activity. Our work suggests while k m measurements are useful for understanding mercury cycling processes, they are less important than surface water MeHg concentrations for assessing MeHg risks to biota. Significant differences in MeHg concentrations between sites with high and low sulphate concentrations may also inform management decisions concerning wetland remediation and creation. - Highlights: • Wetlands of the PPR provide many vital ecosystem services, but can have high MeHg concentrations. • Methylation potentials in prairie ponds are similar to other freshwater wetlands. • MeHg and %MeHg in surface water of high sulphate ponds was greater than low sulphate ponds. • Sediment-porewater partitioning coefficients were small compared to other systems. • Potential methylation rate constants did not correlate to surface water concentrations. - Prairie wetland ponds with higher sulphate concentrations have greater sediment and surface water methylmercury concentrations, but potential methylation rates do not differ

Characterization of the Bacterial and Sulphate Reducing Community in the Alkaline and Constantly Cold Water of the Closed Kotalahti Mine

Directory of Open Access Journals (Sweden)

Malin Bomberg

2015-07-01

Full Text Available Drainage from metal-sulphide rich rocks may cause considerable environmental stress in the form of elevated sulphate and heavy metal contamination of the environment. Mine draining effects from closed mines may be abated using indigenous and introduced microbial communities for sulphate reduction and metal precipitation at the mining site. Here we characterized the general and sulphate reducing bacterial (SRB community of Kotalahti Mine (Finland. The mine was flooded after closure and sulphate reduction and metal precipitation was induced by addition of pig manure sludge into the Vehkankuilu shaft. Water was sampled from Vehkankuilu and Ollinkuilu shafts from depths −10, −30, −70 and −100 m 15 years after the treatment. The water in the shafts differed from each other biologically and geochemically. The shafts are not directly connected except by some fracture zones, and the Ollinkuilu shaft is used as a reference for environmental monitoring. The detected bacterial communities from both shafts contained methylotrophic γ-Proteobacteria, hydrogenotrophic and methylotrophic β-Proteobacteria and fermenting bacterial clades. The concentration of SRB was low, at most 4.0 × 103 dsrB genes·mL−1, and the SRB affiliated with Desulfobulbus and Thermoanaerobacteriales clades. Despite the obvious success of the mine as an in situ bioreactor for increasing water pH and removing sulphate and heavy metals by induced sulphate reduction under suboptimal temperature, only a small portion, less than 0.5%, of the bacterial population in the mine water was SRB.

Profiles of bile acids and their glucuronide and sulphate conjugates in the serum, urine and bile from patients undergoing bile drainage.

OpenAIRE

Takikawa, H; Beppu, T; Seyama, Y

1985-01-01

Bile acid profiles in serum, urine, and bile from patients undergoing bile drainage and the changes of serum bile acids after bile drainage were studied. Bile acids were separated into non-glucuronidate-non-sulphate, glucuronidated, and sulphated fractions and were measured by mass fragmentography using conjugates of deuterium labelled bile acids as internal standards. Glucuronidated and sulphated bile acids contribute 14-32% and 16-44% of serum bile acids, 4-11% and 61-82% of urine bile acid...

Susceptibility of different bacterial species isolated from food animals to copper sulphate, zinc chloride and antimicrobial substances used for disinfection

DEFF Research Database (Denmark)

Aarestrup, Frank Møller; Hasman, Henrik

2004-01-01

that Danish bacterial isolates from livestock so far have not or have only to a limited degree developed resistance to antimicrobial compounds commonly used for disinfection. Acquired copper resistance was only found in enterococci. There were large differences in the intrinsic susceptibility of the different...... of susceptibilities to the different antimicrobial agents. Large variations were observed in the susceptibility of the different bacterial species to the different compounds. Staphylococci were in general very susceptible to all antimicrobial compounds tested. The Salmonella isolates were in general less susceptible...

Improving Beneficiation of Copper and Iron from Copper Slag by Modifying the Molten Copper Slag

Directory of Open Access Journals (Sweden)

Zhengqi Guo

2016-04-01

Full Text Available In the paper, a new technology was developed to improve the beneficiation of copper and iron components from copper slag, by modifying the molten slag to promote the mineralization of valuable minerals and to induce the growth of mineral grains. Various parameters, including binary basicity, dosage of compound additive, modification temperature, cooling rate and the end point temperature of slow cooling were investigated. Meanwhile, optical microscope, scanning electron microscope and energy dispersive spectrometer (SEM-EDS was employed to determine the mineralogy of the modified and unmodified slag, as well as to reveal the mechanisms of enhancing beneficiation. The results show that under the proper conditions, the copper grade of rougher copper concentrate was increased from 6.43% to 11.04%, iron recovery of magnetic separation was increased significantly from 32.40% to 63.26%, and other evaluation indexes were changed slightly, in comparison with unmodified copper slag. Moreover, matte and magnetite grains in the modified slag aggregated together and grew obviously to the mean size of over 50 μm, resulting in an improvement of beneficiation of copper and iron.

Assessment of a DNA vaccine encoding an anchored-glycosylphosphatidylinositol tegumental antigen complexed to protamine sulphate on immunoprotection against murine schistosomiasis

Directory of Open Access Journals (Sweden)

Eduardo JM Nascimento

2007-02-01

Full Text Available Protamine sulphate/DNA complexes have been shown to protect DNA from DNase digestion in a lipid system for gene transfer. A DNA-based vaccine complexed to protamine sulphate was used to induce an immune response against Schistosoma mansoni anchored-glycosylphosphatidylinositol tegumental antigen in BALB/c mice. The protection elicited ranged from 33 to 44%. The spectrum of the elicited immune response induced by the vaccine formulation without protamine was characterized by a high level of IgG (IgG1> IgG2a. Protamine sulphate added to the DNA vaccine formulation retained the green fluorescent protein encoding-plasmid longer in muscle and spleen. The experiments in vivo showed that under protamine sulphate effect, the scope of protection remained unchanged, but a modulation in antibody production (IgG1= IgG2a was observed.

21 CFR 73.1125 - Potassium sodium copper chloropyhllin (chlorophyllin-copper complex).

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Potassium sodium copper chloropyhllin (chlorophyllin-copper complex). 73.1125 Section 73.1125 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT....1125 Potassium sodium copper chloropyhllin (chlorophyllin-copper complex). (a) Identity. (1) The color...

21 CFR 73.2125 - Potassium sodium copper chlorophyllin (chlorophyllin-copper complex).

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Potassium sodium copper chlorophyllin (chlorophyllin-copper complex). 73.2125 Section 73.2125 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT... § 73.2125 Potassium sodium copper chlorophyllin (chlorophyllin-copper complex). (a) Identity and...

Comparison of amiodarone vs magnesium sulphate in the prevention of atrial fibrillation after coronary artery bypass grafting surgery

International Nuclear Information System (INIS)

Bashir, I.; Abbas, S.

2013-01-01

Background: Atrial fibrillation (AF) is common in patients after coronary artery bypass grafting (CABG) and can result in increased morbidity and mortality, increased length of hospital stay, and increased cost. In this study we compared the efficacy of amiodarone versus magnesium sulphate in the prophylaxis of post-CABG atrial fibrillation. Objective: This study was carried out to assess the efficacy of amiodarone in comparison to magnesium sulphate in the prevention of atrial fibrillation after coronary artery bypass grafting. Study Design: Randomized controlled trials. Place and duration of study: The study was carried out at Armed Forces Institute of Cardiology and National Institute of Heart Diseases, Rawalpindi from July 2010 to December 2011 Patients and Methods: Total 240 patients were included in the study and randomly divided in two groups of 120 each using random number table. Patients in Group A (Amiodarone group) were given a loading dose of amiodarone 5 mg/Kg after induction of anesthesia which was then continued as infusion at 5 micro gm/Kg/minute on first postoperative day. This was followed by an oral dose of 600 mg/day postoperatively for 5 days. Those in Group B (Magnesium Sulphate group) received 2 g of magnesium sulphate in 100 ml of isotonic 0.9% solution intravenously over 1 hour at following times: preoperatively, immediately following the operation, and on postoperative days 1, 2, and 3. Results: Thirteen patients (10.8%) developed AF in Amiodarone group, compared to 31 patients (25.8%) in magnesium sulphate group. The results proved amiodarone to be more effective than magnesium sulphate in preventing post-CABG AF (p<0.001). Thirty one patients who developed AF postoperatively in the magnesium group were treated with amiodarone, and all patients recovered normal sinus rhythm. In the amiodarone prophylaxis group, 9 patients regained sinus rhythm in 6 - 8 hours, while for 4 remaining patients cardioversion was attempted out of which 2

Production of granules of urea, urea-ammonium sulphate and urea-potassium chloride enriched with 15N

International Nuclear Information System (INIS)

Bendassolli, J.A.

1991-01-01

Using a pearling tower it was possible to produce granulated urea, and granulated mixtures of ammonium sulphate and urea, potassium chloride and urea, Labelled in 15 N. Granulated urea with 1, 2, 3 and 4 mm of diameter was obtained using a system with a heating controller. A low concentration of biuret was observed in the granules produced ( 15 N-Labelled ( 15 NH 4' 15 NH 2 ) with variable proportion of ammonium sulphate and urea. (author)

Presidential Green Chemistry Challenge: 2009 Academic Award

Science.gov (United States)

Presidential Green Chemistry Challenge 2009 award winner, Professor Krzysztof Matyjaszewski, developed Atom Transfer Radical Polymerization to make polymers with copper catalysts and environmentally friendly reducing agents.

Streptococcus mutans copper chaperone, CopZ, is critical for biofilm formation and competitiveness.

Science.gov (United States)

Garcia, S S; Du, Q; Wu, H

2016-12-01

The oral cavity is a dynamic environment characterized by hundreds of bacterial species, saliva, and an influx of nutrients and metal ions such as copper. Although there is a physiologic level of copper in the saliva, the oral cavity is often challenged with an influx of copper ions. At high concentrations copper is toxic and must therefore be strictly regulated by pathogens for them to persist and cause disease. The cariogenic pathogen Streptococcus mutans manages excess copper using the copYAZ operon that encodes a negative DNA-binding repressor (CopY), the P1-ATPase copper exporter (CopA), and the copper chaperone (CopZ). These hypothetical roles of the copYAZ operon in regulation and copper transport to receptors led us to investigate their contribution to S. mutans virulence. Mutants defective in the copper chaperone CopZ, but not CopY or CopA, were impaired in biofilm formation and competitiveness against commensal streptococci. Characterization of the CopZ mutant biofilm revealed a decreased secretion of glucosyltransferases and reduced expression of mutacin genes. These data suggest that the function of copZ on biofilm and competitiveness is independent of copper resistance and CopZ is a global regulator for biofilm and other virulence factors. Further characterization of CopZ may lead to the identification of new biofilm pathways. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Inhibition of Bio corrosion of steel coupon by sulphate reducing ...

African Journals Online (AJOL)

ADOWIE PERE

Inhibition of Bio corrosion of steel coupon by sulphate reducing bacteria and Iron oxidizing bacteria using .... Ethanol for 24 h. The extract was ... with distilled water to get a zero reading from the meter before .... Ethanol extract of musa species peels as a green corrosion ... Eco friendly extract of banana peel as corrosion ...

Magnesium sulphate and amiodarone prophylaxis for prevention of postoperative arrhythmia in coronary by-pass operations

Directory of Open Access Journals (Sweden)

Huysal Kagan

2009-02-01

Full Text Available Abstract Background The aim of this study was to investigate the use of prophylactic magnesium sulphate and amiodarone in treating arrhythmias that may occur following coronary bypass grafting operations. Methods The study population consisted of 192 consecutive patients who were undergoing coronary artery bypass grafting (CABG. Sixty-four patients were given 3 g of magnesium sulphate (MgSO4 [20 ml = 24.32 mEq/L Mg+2] in 100 cc of isotonic 0.9% solution over 2 hours intravenously at the following times: 12 hours prior to the operation, immediately following the operation, and on postoperative days 1, 2, and 3 (Group 1. Another group of 64 patients was given a preoperative infusion of amiodarone (1200 mg on first post-operative day (Group 2. After the operation amiodarone was administered orally at a dose of 600 mg/day. Sixty-four patients in group 3 (control group had 100 cc. isotonic 0.9% as placebo, during the same time periods. Results In the postoperative period, the magnesium values were significantly higher in Group 1 than in Group 2 for all measurements. The use of amiodarone for total arrhythmia was significantly more effective than prophylactic treatment with magnesium sulphate (p = 0.015. There was no difference between the two drugs in preventing supraventricular arrhythmia, although amiodarone significantly delayed the revealing time of atrial fibrillation (p = 0.026. Ventricular arrhythmia, in the form of ventricular extra systole, was more common in the magnesium prophylaxis group. The two groups showed no significant differences in other operative or postoperative measurements. No side effects of the drugs were observed. Conclusion Prophylactic use of magnesium sulphate and amiodarone are both effective at preventing arrhythmia that may occur following coronary by-pass operations. Magnesium sulphate should be used in prophylactic treatment since it may decrease arrhythmia at low doses. If arrhythmia should occur despite this

The importance of SO{sub 2} and SO{sub 3} for sulphation of gaseous KCl - An experimental investigation in a biomass fired CFB boiler

Energy Technology Data Exchange (ETDEWEB)

Kassman, Haakan [Vattenfall Power Consultant AB, Nykoeping (Sweden); Chalmers University of Technology, Department of Energy and Environment, Division of Energy Technology, Gothenburg (Sweden); Baefver, Linda [Technical Research Institute of Sweden, Energy Technology, Boraas (Sweden); Aamand, Lars-Erik [Chalmers University of Technology, Department of Energy and Environment, Division of Energy Technology, Gothenburg (Sweden)

2010-09-15

This paper is based on results obtained during co-combustion of wood pellets and straw in a 12 MW circulating fluidised bed (CFB) boiler. Elemental sulphur (S) and ammonium sulphate ((NH{sub 4}){sub 2}SO{sub 4}) were used as additives to convert the alkali chlorides (mainly KCl) to less corrosive alkali sulphates. Their performance was then evaluated using several measurement tools including, IACM (on-line measurements of gaseous alkali chlorides), a low-pressure impactor (particle size distribution and chemical composition of extracted fly ash particles), and deposit probes (chemical composition in deposits collected). The importance of the presence of either SO{sub 2} or SO{sub 3} for gas phase sulphation of KCl is also discussed. Ammonium sulphate performed significantly better than elemental sulphur. A more efficient sulphation of gaseous KCl was achieved with (NH{sub 4}){sub 2}SO{sub 4} even when the S/Cl molar ratio was less than half compared to sulphur. Thus the presence of gaseous SO{sub 3} is of greater importance than that of SO{sub 2} for the sulphation of gaseous KCl. (author)

Nickel, copper and cobalt coalescence in copper cliff converter slag

Directory of Open Access Journals (Sweden)

Wolf A.

2016-01-01

Full Text Available The aim of this investigation is to assess the effect of various additives on coalescence of nickel, copper and cobalt from slags generated during nickel extraction. The analyzed fluxes were silica and lime while examined reductants were pig iron, ferrosilicon and copper-silicon compound. Slag was settled at the different holding temperatures for various times in conditions that simulated the industrial environment. The newly formed matte and slag were characterized by their chemical composition and morphology. Silica flux generated higher partition coefficients for nickel and copper than the addition of lime. Additives used as reducing agents had higher valuable metal recovery rates and corresponding partition coefficients than fluxes. Microstructural studies showed that slag formed after adding reductants consisted of primarily fayalite, with some minute traces of magnetite as the secondary phase. Addition of 5 wt% of pig iron, ferrosilicon and copper-silicon alloys favored the formation of a metallized matte which increased Cu, Ni and Co recoveries. Addition of copper-silicon alloys with low silicon content was efficient in copper recovery but coalescence of the other metals was low. Slag treated with the ferrosilicon facilitated the highest cobalt recovery while copper-silicon alloys with silicon content above 10 wt% resulted in high coalescence of nickel and copper, 87 % and 72 % respectively.

Salbutamol sulphate-ethylcellulose microparticles: formulation and in-vitro evaluation with emphasis on mathematical approaches

Directory of Open Access Journals (Sweden)

G Murtaza

2009-10-01

Full Text Available "n "nBackground and the purpose of the study: This study reports the laboratory optimization for the preparation of salbutamol sulphate-ethylcellulose microparticles by a non-solvent addition coacervation technique through adjustment of the ratio of salbutamol sulphate to ethylcellulose. The variation of drug release between the microparticles and tabletted microparticles was also investigated. "nMethods: In vitro release profiles of developed microparticles and tabletted microparticles were studied using USP XXIV dissolution apparatus I and II, respectively, in 450 ml double distilled water at 50 rpm maintained at 37°C. "nResults: White microparticles with no definite shape having good entrapment efficiency (96.68 to 97.83% and production yield (97.48 ± 1.21 to 98.35 ± 1.08% were obtained. In this investigation, initial burst effect was observed in the drug release behavior. The rate of drug release from microparticles decreased as the concentration of polyisobutylene was increased from 6% to 12% during microencapsulation. The release pattern of tabletted microparticles was affected significantly (p < 0.05 by the addition of hydroxy propyl methyl cellulose (HPMC as excepient and insignificantly (p > 0.05 by the type of dissolution media and stirring speed. Tabletted microparticles showed good stability and reproducibility. Ethylcellulose was found to be compatible with salbutamol sulphate. The drug release from all formulations was best fit to Higuchi's equation and the mechanism of drug release was anomalous diffusion from all formulations. "nConclusion: The results of this study suggest that by using ethylcellulose it is possible to design a single-unit, sustained-release oral dosage form of salbutamol sulphate for indication of twice a day.

Antimicrobial and bone-forming activity of a copper coated implant in a rabbit model.

Science.gov (United States)

Prinz, Cornelia; Elhensheri, Mohamed; Rychly, Joachim; Neumann, Hans-Georg

2017-08-01

Current strategies in implant technology are directed to generate bioactive implants that are capable to activate the regenerative potential of the surrounding tissue. On the other hand, implant-related infections are a common problem in orthopaedic trauma patients. To meet both challenges, i.e. to generate a bone implant with regenerative and antimicrobial characteristics, we tested the use of copper coated nails for surgical fixation in a rabbit model. Copper acetate was galvanically deposited with a copper load of 1 µg/mm 2 onto a porous oxide layer of Ti6Al4V nails, which were used for the fixation of a tibia fracture, inoculated with bacteria. After implantation of the nail the concentration of copper ions did not increase in blood which indicates that copper released from the implant was locally restricted to the fracture site. After four weeks, analyses of the extracted implants revealed a distinct antimicrobial effect of copper, because copper completely prevented both a weak adhesion and firm attachment of biofilm-forming bacteria on the titanium implant. To evaluate fracture healing, radiographic examination demonstrated an increased callus index in animals with copper coated nails. This result indicates a stimulated bone formation by releasing copper ions. We conclude that the use of implants with a defined load of copper ions enables both prevention of bacterial infection and the stimulation of regenerative processes.

Microneedle-Mediated Delivery of Copper Peptide Through Skin.

Science.gov (United States)

Li, Hairui; Low, Yong Sheng Jason; Chong, Hui Ping; Zin, Melvin T; Lee, Chi-Ying; Li, Bo; Leolukman, Melvina; Kang, Lifeng

2015-08-01

Copper peptide (GHK-Cu) plays an important role in skin regeneration and wound healing. However, its skin absorption remains challenging due to its hydrophilicity. Here we use polymeric microneedle array to pre-treat skin to enhance GHK-Cu skin penetration. Two in vitro skin models were used to assess the capability of microneedles in facilitating skin delivery of GHK-Cu. Histological assay and confocal laser scanning microscopy were performed to characterize and quantify the microconduits created by the microneedles inside skin. Cellular and porcine models were used to evaluate the safety of microneedle-assisted copper peptide delivery. The depth and percentage of microneedle penetration were correlated with application forces, which in turn influenced the extent of enhancement in the skin permeability of GHK-Cu. In 9 h, 134 ± 12 nanomoles of peptide and 705 ± 84 nanomoles of copper permeated though the microneedle treated human skin, while almost no peptide or copper permeated through intact human skin. No obvious signs of skin irritation were observed with the use of GHK-Cu after microneedle pretreatment. It is effective and safe to enhance the skin permeation of GHK-Cu by using microneedles. This approach may be useful to deliver similar peptides or minerals through skin.

Antwerp Copper Plates

DEFF Research Database (Denmark)

Wadum, Jørgen

1999-01-01

In addition to presenting a short history of copper paintings, topics detail artists’ materials and techniques, as well as aspects of the copper industry, including mining, preparation and trade routes.......In addition to presenting a short history of copper paintings, topics detail artists’ materials and techniques, as well as aspects of the copper industry, including mining, preparation and trade routes....

The use of magnesium sulphate for the treatment of severe pre ...

African Journals Online (AJOL)

Background : Pre-eclampsia and eclampsia are important causes of maternal and perinatal morbidity and mortality in the developing countries. There is need to provide the most effective management to pre-eclamptic and eclamptic patients. There is now evidence that magnesium sulphate is the most effective ...

Comparison of spray congealing and melt emulsification methods for the incorporation of the water-soluble salbutamol sulphate in lipid microparticles.

Science.gov (United States)

Scalia, Santo; Traini, Daniela; Young, Paul M; Di Sabatino, Marcello; Passerini, Nadia; Albertini, Beatrice

2013-02-01

Salbutamol sulphate is widely used as bronchodilator for the treatment of asthma. Its use is limited by the relatively short duration of action and hence sustained delivery of salbutamol sulphate offers potential benefits to patients. This study explores the preparation of lipid microparticles (LMs) as biocompatible carrier for the prolonged release of salbutamol sulphate. The LMs were produced using different lipidic materials and surfactants, by classical melt emulsification-based methods (oil-in-water and water-in-oil-in-water emulsions) and the spray congealing technique. For the LMs obtained by melt emulsification a lack of release modulation was observed. On the other hand, the sustained release of salbutamol sulphate was achieved with glyceryl behenate microparticles prepared by spray congealing. These LMs were characterized by scanning electron microscopy, X-ray diffractometry and differential scanning calorimetry. The drug loading was 4.72% (w/w). The particle size distribution measured by laser diffraction and electrical zone sensing was represented by a volume median diameter (Dv(50)) of 51.7-71.4 µm. Increasing the atomization air pressure from 4 to 8 bar produced a decrease of the Dv(50) to 12.7-17.5 µm. Incorporation of the hydrophilic salbutamol sulphate into LMs with sustained release characteristics was achieved by spray congealing.

Performance of sulphate- and selenium-reducing biochemical reactors using different ratios of labile to recalcitrant organic materials.

Science.gov (United States)

Mirjafari, Parissa; Baldwin, Susan A

2015-01-01

Successful operation of sulphate-reducing bioreactors using complex organic materials depends on providing a balance between more easily degrading material that achieves reasonable kinetics and low hydraulic retention times, and more slowly decomposing material that sustains performance in the long term. In this study, two organic mixtures containing the same ingredients typical of bioreactors used at mine sites (woodchips, hay and cow manure) but with different ratios of wood (recalcitrant) to hay (labile) were tested in six continuous flow bioreactors treating synthetic mine-affected water containing 600 mg/L of sulphate and 15 μg/L of selenium. The reactors were operated for short (5-6 months) and long (435-450 days) periods of time at the same hydraulic retention time of 15 days. There were no differences in the performance of the bioreactors in terms of sulphate-reduction over the short term, but the wood-rich bioreactors experienced variable and sometimes unreliable sulphate-reduction over the long term. Presence of more hay in the organic mixture was able to better sustain reliable performance. Production of dissolved organic compounds due to biodegradation within the bioreactors was detected for the first 175-230 days, after which their depletion coincided with a crash phase observed in the wood-rich bioreactors only.

Effects of ovariectomization (OVX) and Synovex-Plus on the ...

African Journals Online (AJOL)

Clayton Bailey

g/kg; cobalt carbonate, 0.02 g/kg; copper sulphate, 1.57 g/kg; iron sulphate, 1.33 g/kg; ... and exsanguination, beginning at 07:00, at the University of Arizona Meats ... sample well on every plate and all samples were run with iTaq SYBR Green ...

Control strategies for bovine dermatophilosis with particular ...

African Journals Online (AJOL)

The various control strategies for Dermatophilosis are discussed in this paper. Recommendations for control of Dermatophilosis in Nigeria on short term include ecto-parasite control by regular use of insecticide/acaricide in dips with added 0.03% copper sulphate or 1% solution of alum (potassium aluminium sulphate) ...

Treatment of acid and sulphate-rich effluents in an integrated ...

African Journals Online (AJOL)

driniev

2004-04-02

Apr 2, 2004 ... sludge obtained from a sewage treatment plant. Sludge was recy- ... tration (0 - 1 g/l); alkalinity (0 - 1 g/l); CaCO3 solids concentration. (0 - 1 g/l); COD (0.5 - 2 ..... Ph.D. Thesis, Agricultural University of Wageningen. 103 pp. ... VISSER A (1995) The Anaerobic Treatment of Sulphate Containing Waste. Water.

Effect of fly ash content towards Sulphate resistance of oil palm shell lightweight aggregate concrete

Science.gov (United States)

Muthusamy, K.; Fadzil, M. Y.; Nazrin Akmal, A. Z. Muhammad; Ahmad, S. Wan; Nur Azzimah, Z.; Hanafi, H. Mohd; Mohamad Hafizuddin, R.

2018-04-01

Both oil palm shell (OPS) and fly ash are by-product generated from the industries. Disposal of these by-product as wastes cause negative impact to the environment. The use of both oil palm shell and fly ash in concrete is seen as an economical solution for making green and denser concrete. The primary aim of this research is to determine the effects of FA utilization as sand replacement in oil palm shell lightweight aggregate concrete (OPS LWAC) towards sulphate resistance. Five concrete mixes containing fly ash as sand replacement namely 0%, 10%, 20%, 30% and 40% were prepared in these experimental work. All mixes were cast in form of cubes before subjected to sulphate solution for the period of 5 months. It was found that addition of 10% fly ash as sand replacement content resulted in better sulphate resistance of OPS LWAC. The occurrence of pozzolanic reaction due to the presence of FA in concrete has consumed the vulnerable Calcium hydroxide to be secondary C-S-H gel making the concrete denser and more durable.

Cysteic acid and taurine synthesis from sulphate in the chick embryo

International Nuclear Information System (INIS)

Chapeville, F.

1960-01-01

The formation of taurine from sulphate was studied in the chick embryo using the radioisotopes of: sulphur, carbon and hydrogen. The following reactions occur: 1) reduction of sulphate to sulphite; 2) fixation of the sulphite on a carbon chain with an amino group, resulting from desulphydration of L-cysteine, which leads to the formation of L-cysteic acid; 3) decarboxylation of L-cysteic acid. Reaction (1) takes place only in the endo-dermal cells of the yolk sac; reaction (2) in these same cells and in the yolk; reaction (3) is general, localized in the yolk sac, in the yolk as well as in the tissues of the embryo itself. The enzyme which catalyses reaction (2) has been purified; the coenzyme is pyridoxal phosphate. The desulphydration of cysteine by this enzyme is a reversible reaction. In non-physiological conditions of concentration and temperature, pyridoxal phosphate catalyses in the presence of metallic ions, the desulphydration of cysteine and the formation of cysteic acid from sulphite. (author) [fr

Decline in Performance of Biochemical Reactors for Sulphate Removal from Mine-Influenced Water is Accompanied by Changes in Organic Matter Characteristics and Microbial Population Composition

Directory of Open Access Journals (Sweden)

Parissa Mirjafari

2016-03-01

Full Text Available Successful long-term bioremediation of mining-influenced water using complex organic matter and naturally-occurring microorganisms in sub-surface flow constructed wetlands requires a balance between easily and more slowly degrading material. This can be achieved by combining different types of organic materials. To provide guidance on what mixture combinations to use, information is needed on how the ratio of labile to recalcitrant components affects the degradation rate and the types of microbial populations supported. To investigate this, different ratios of wood and hay were used in up-flow column bioreactors treating selenium- and sulphate-containing synthetic mine-influenced water. The degradation rates of crude fibre components appeared to be similar regardless of the relative amounts of wood and hay. However, the nature of the degradation products might have differed in that those produced in the hay-rich bioreactors were more biodegradable and supported high sulphate-reduction rates. Microorganisms in the sulphate-reducing and cellulose-degrading inocula persisted in the bioreactors indicating that bio-augmentation was effective. There was a shift in microbial community composition over time suggesting that different microbial groups were involved in decomposition of more recalcitrant material. When dissolved organic carbon (DOC was over-supplied, the relative abundance of sulphate-reducers was low even through high sulphate-reduction rates were achieved. As DOC diminished, sulphate-reducers become more prevalent and their relative abundance correlated with sulphate concentrations rather than sulphate-reduction rate.

Speciation and leachability of copper in mine tailings from porphyry copper mining

DEFF Research Database (Denmark)

Hansen, Henrik K.; Yianatos, Juan B; Ottosen, Lisbeth M.

2005-01-01

Mine tailing from the El Teniente-Codelco copper mine situated in VI Region of Chile was analysed in order to evaluate the mobility and speciation of copper in the solid material. Mine tailing was sampled after the rougher flotation circuits, and the copper content was measured to 1150mgkg^-^1 dry...... matter. This tailing was segmented into fractions of different size intervals: 0-38, 38-45, 45-53, 53-75, 75-106, 106-150, 150-212, and >212@mm, respectively. Copper content determination, sequential chemical extraction, and desorption experiments were carried out for each size interval in order...... to evaluate the speciation of copper. It was found that the particles of smallest size contained 50-60% weak acid leachable copper, whereas only 32% of the copper found in largest particles could be leached in weak acid. Copper oxides and carbonates were the dominating species in the smaller particles...

Influence of sulphate on effects of ADP, 3′,5′-cyclic amp and citrate on human platelet phosphofructokinase activity

NARCIS (Netherlands)

Akkerman, Jan Willem N.; Gorter, G.; Sixma, J.J.; Staal, Gerard E.J.

1974-01-01

1. 1. Sulphate ions activate partially-purified human platelet phosphofructokinase. This is caused by suppression of the cooperativity of the enzyme with respect to fructose 6-phosphate. 2. 2. Sulphate therefore markedly affects the influences of allosteric modifiers such as ADP, 3′,5′-cyclic AMP

Tribological properties of copper-based composites with copper coated NbSe2 and CNT

International Nuclear Information System (INIS)

Chen, Beibei; Yang, Jin; Zhang, Qing; Huang, Hong; Li, Hongping; Tang, Hua; Li, Changsheng

2015-01-01

Graphical abstract: Morphology of copper coated NbSe 2 and CNT; friction coefficient and wear rate of copper-based composites. - Highlights: • NbSe 2 and CNT were coated with copper layers by the means of electroless plating. • The mechanical and tribological properties of copper composites were studied. • The enhancement mechanisms of copper coated NbSe 2 and CNT were proposed. • Copper–copper coated (12 wt.%NbSe 2 –3 wt.%CNT) composite had the best wear resistance. - Abstract: Copper-based composites with copper coated NbSe 2 and/or CNT were fabricated by the powder metallurgy technique. The morphology and phase composition of copper coated NbSe 2 and carbon nanotube (CNT) were observed using high solution transmission electronic microscope (HRTEM), scanning electronic microscope (SEM equipped with EDS) and X-ray diffraction (XRD). The density, hardness, and bending strength of as-prepared copper-based composites were measured, and their tribological properties were investigated using UMT-2 tester. Results indicated that all copper-based composites showed decreased density and bending strength, but increased hardness in comparison with copper matrix. Besides, the incorporation of copper coated NbSe 2 improved the friction-reducing and anti-wear properties of copper matrix. Addition of copper coated CNT greatly enhanced the mechanical and tribological properties. In particular, when the content of copper coated CNT was 3 wt.%, the corresponding composite exhibited the best tribological properties. This was because NbSe 2 was distributed chaotically in matrix, which greatly improved the friction-reducing property of copper, while CNT with superior mechanical strength enhanced the wear resistance by increasing the load-carrying capacity. More importantly, copper layers coated on NbSe 2 and CNT favored the good interfacial combination between fillers and copper matrix showing beneficial effect for the stresses transferring from matrix to fillers

Copper and Anesthesia: Clinical Relevance and Management of Copper Related Disorders

OpenAIRE

Langley, Adrian; Dameron, Charles T.

2013-01-01

Recent research has implicated abnormal copper homeostasis in the underlying pathophysiology of several clinically important disorders, some of which may be encountered by the anesthetist in daily clinical practice. The purpose of this narrative review is to summarize the physiology and pharmacology of copper, the clinical implications of abnormal copper metabolism, and the subsequent influence of altered copper homeostasis on anesthetic management.

Effect of some heavy metals on the growth and development of Pleurotus tuber-regium.

Directory of Open Access Journals (Sweden)

Akpaja EO

2012-02-01

Full Text Available The effects of five heavy metals (cadmium, copper, mercury, lead and zinc on the growth and fruit body production in Pleurotus tuber-regium was investigated. Lead sulphate, zinc sulphate, copper sulphate, cadmium nitrate and mercury chloride were added to garden soil at concentrations of 0, 0.125, 0.25, 0.5, 1.0, and 2.0 mmol per 3 kg of soil. Sclerotia of the test mushroom were used to inoculate the artificially contaminated soil. Mercury prevented growth and fruit body production in P. tuber-regium. Fungal morphometry was greatly affected by lead. The heavy metal content in the fungal biomass complex increased with increase of heavy metal concentration in the soil. The highest concentration (183.06 mg/kg was found in zinc at 2 mmol/L.

Industrial Tests to Modify Molten Copper Slag for Improvement of Copper Recovery

Science.gov (United States)

Guo, Zhengqi; Zhu, Deqing; Pan, Jian; Zhang, Feng; Yang, Congcong

2018-04-01

In this article, to improve the recovery of copper from copper slag by flotation process, industrial tests of the modification process involving addition of a composite additive into molten copper slag were conducted, and the modified slag was subjected to the flotation process to confirm the modification effect. The phase evolution of the slag in the modification process was revealed by thermodynamic calculations, x-ray diffraction, optical microscopy and scanning electron microscopy. The results show that more copper was transformed and enriched in copper sulfide phases. The magnetite content in the modified slag decreased, and that of "FeO" increased correspondingly, leading to a better fluidity of the molten slag, which improved the aggregation and growth of fine particles of the copper sulfide minerals. Closed-circuit flotation tests of the original and modified slags were conducted, and the results show that the copper recovery increased obviously from 69.15% to 73.38%, and the copper grade of concentrates was elevated slightly from 20.24% to 21.69%, further confirming that the industrial tests of the modification process were successful. Hence, the modification process has a bright future in industrial applications for enhancing the recovery of copper from the copper slag.

Intravesical Glycosaminoglycan Replacement with Chondroitin Sulphate (Gepan(®) instill) in Patients with Chronic Radiotherapy- or Chemotherapy-Associated Cystitis.

Science.gov (United States)

Schwalenberg, Thilo; Berger, Frank Peter; Horn, Lars Christian; Thi, Phuc Ho; Stolzenburg, Jens-Uwe; Neuhaus, Jochen

2015-08-01

Intravesical instillation of glycosaminoglycans is a promising option for the treatment of chronic cystitis, as it supports the regeneration of the damaged urothelial layer. We investigated the efficacy of short-term intravesical chondroitin sulphate treatment (six courses of instillation) in patients with chronic radiotherapy- or chemotherapy-associated cystitis. This prospective, observational study included patients with chronic radiotherapy- or chemotherapy-associated cystitis, who received six once-weekly intravesical instillations of 0.2% chondroitin sulphate 40 mL. Every week, patients recorded their symptoms and their benefits and tolerance of treatment, using a self-completed questionnaire. The study included 16 patients (mean age 68.5 years; 50% male). During the study, a reduction in all evaluated parameters was observed. After one dose of chondroitin sulphate, symptom improvement was observed in 38% of patients, and after the second dose, an additional 31% of patients showed improvement. At week 6, 80% of patients had either improved or were symptom free, and significant improvements in urinary urgency (p = 0.0082), pollakisuria (p = 0.0022), urge frequency (p = 0.0033) and lower abdominal pain (p = 0.0449) were observed. Haematuria, present in 9 of the 16 patients at baseline, was completely resolved in all cases after 6 weeks. The majority of patients (93%) evaluated the tolerance of chondroitin sulphate as 'good' or 'very good'. No treatment-related adverse events were reported. Intravesical administration of chondroitin sulphate was effective for the treatment of radiotherapy- or chemotherapy-associated cystitis. Even short-term treatment appears to be effective in reducing symptoms and improving the quality of life of patients.

Alternative method of portable irradiation of manganese sulphate solution by an plutonium-beryllium source for manganese sulphate bath efficiency measurements

International Nuclear Information System (INIS)

Silva, Fellipe Souza da; Martins, Marcelo Marques; Pereira, Walsan Wagner

2016-01-01

This study intends to create an alternative irradiation system from a Plutonium-Beryllium source for manganese sulphate solution using the Monte Carlo code. Thus seeking to eliminate the issue of institutes that do not have reactors or particle accelerators in its infrastructure, in order to optimize and provide independence for them to carry out efficiency measurements of MnSO_4 solution in their own locality. The Monte Carlo simulations defined the technical features of this new system so that the solution reaches the maximum neutron capture by manganese in solution. (author)

Effects of replacing a dietary antibacterial agent (zinc bacitracin) with copper salts in Cherry Valley Pekin meat ducks.

Science.gov (United States)

Wu, D W; Wang, L C; Wen, C; Hooge, D M; Liang, C; Zhou, Y M

2013-01-01

1. A study was conducted to investigate the effectiveness of high dietary copper concentrations obtained from tribasic copper chloride (TBCC, 58% copper) and copper sulphate pentahydrate (CuSO4, 25% copper) in replacing antibiotic growth promoters (AGP) in duck diets. 2. A total of 960 one-day-old Cherry Valley meat-strain ducks were divided into 3 treatment groups, with 8 replicates per treatment, in a 6-week feeding trial. The ducks were fed a basal diet supplemented with AGP (40 mg zinc bacitracin/kg and 40 mg garlicin/kg of diet) or 150 mg of Cu/kg of diet, given as either CuSO4 or TBCC. 3. The body weight, average daily gain, average daily feed intake and mortality of ducks were not affected by the dietary treatments. However, the feed/gain ratio of ducks that were fed TBCC diets was significantly lower than those of ducks that were fed CuSO4 diets and were similar to those in the AGP group. 4. TBCC increased the Cu content in the liver tissue of ducks compared with the content in those that were fed the diet supplemented with AGP. TBCC also increased the Fe and Zn content in breast muscles compared with that in ducks that were fed the diet supplemented with CuSO4. 5. The activities of superoxide dismutase (SOD) and glutathione peroxidase (GSH-Px) were significantly higher in the serum of ducks that received the diet supplemented with TBCC than AGP or CuSO4. TBCC treatment decreased the malondialdehyde (MDA) content in serum of ducks compared with groups supplemented with CuSO4. 6. No significant difference was observed in liver or muscle fat content among the different dietary treatment groups. The serum low-density lipoprotein cholesterol concentration was lower in ducks fed AGP diets than those fed CuSO4 diets. 7. It was concluded that the replacement of AGP with 150 mg of Cu/kg of feed from TBCC improved the feed efficiency, trace mineral deposition and antioxidant status more than when the source of copper was CuSO4.

Influence of sulphate ions on the composition and structure of the oxide films on stainless steel and nickel alloys in simulated BWR crack conditions

International Nuclear Information System (INIS)

Bojinov, M.; Kinnunen, P.; Laitinen, E.; Maekelae, K.; Saario, T.; Sirkiae, P.; Toivonen, A.; Campbell, J.M.; Johansson, L.S.; Helin, M.; Muttilainen, E.; Reinvall, A.; Ollonqvist, T.; Vaeyrynen, J.

2002-01-01

The goal of the present work has been to clarify the influence of sulphate ions on the oxide films formed on stainless steel and Ni-based alloys in simulated crack chemistry conditions using different ex situ analytical techniques. The main observations of this work can be summarised as follows: The thickness of the films formed in simulated oxygen-free crack chemistry conditions during an exposure of circa 4 days varies roughly in the range 200..500 nm, which corresponds to observations reported in the literature [2]. The presence of 10000 ppb sulphate ions in simulated crack tip conditions seems to lead to a considerably lower thickness of the oxide films when compared to sulphate-free conditions. The presence of 10000 ppb sulphate ions leads also to considerable changes in the morphology of the oxide crystals on the material samples. In the absence of sulphate the outer oxide layer contains elongated round-edged crystals, while in the presence of sulphate ions the crystals are longish and needle-like. No visible difference can be observed in the outlook of the crystals formed on stainless steel and Inconel alloy surfaces. A small amount of sulphur in the form of sulphate can be found on the oxide surface on all the studied materials after exposure to the 10000 ppb solution. Sulphur seems to become incorporated inside the oxide film on AISI 316 L(NG). It is not clear at this stage, whether the observed influence of the sulphate ions can be ascribed to the lower pH, to a possible effect on solubility or to a direct influence of the anionic species. (authors)

The Sulphate Effect on Lijiaxia Concrete Dam (China Gallery

Directory of Open Access Journals (Sweden)

Xufen Zhu

2017-01-01

Full Text Available The concrete degradation is one of the most serious problems for a dam construct during the normal operation, which determines the dam service life. Hence, it is very important to reduce the extent of the dam concrete degradation for the safety of the dam normal operation. Here, Lijiaxia hydroelectric station is taken as an example, and a comprehensive method to assess the sulphate effect on dam gallery is proposed. Eleven samples in total were taken from three difference locations by the drill bore. The microstructural investigations including X-ray fluorescence spectrometry (XRF, X-ray diffraction (XRD, scanning electron microscope (SEM, and energy dispersive spectroscopy (EDS were conducted to assess the sulphate attack and the degradation degree. Meanwhile, the water chemical analysis was applied to reveal the mechanism of concrete degradation. The experimental and analysis results indicate that the concrete degradation degree varies with the location of the samples. The components of the concrete change and the content of SO3 increase dramatically during degradation. Moreover, the mineral facies of the concrete change correspondingly, with the cement paste substituted by the calcite, calcium vitriol, and gypsum. The reinforcement and precaution measures are suggested based on the results of the degradation assessment.

Polyferric sulphate: preparation, characterisation and application in coagulation experiments.

Science.gov (United States)

Zouboulis, A I; Moussas, P A; Vasilakou, F

2008-07-15

The process of coagulation is a core environmental protection technology, which is mainly used in the water or wastewater treatment facilities. Research is now focused on the development of inorganic pre-polymerised coagulants. A characteristic example is PFS (polyferric sulphate), a relatively new pre-polymerised inorganic coagulant with high cationic charge. In this paper, the role of major parameters, including temperature, types of chemical reagents, ratio r=[OH]/[Fe], rate of base addition in the preparation stages of PFS were investigated. Furthermore, the prepared PFS was characterised based on typical properties, such as the percentage of the polymerised iron present in the compound, z-potential, pH, etc. Moreover, dynamics of coagulation process were examined by means of the Photometric Dispersion Analyzer (PDA). Finally, the coagulation efficiency of PFS in treating kaolin suspension and biologically pre-treated wastewater was evaluated in comparison with the respective conventional coagulant agent. The results indicate that certain parameters, such as the r value, the rate of base addition and the duration and temperature of the polymerisation stage, significantly affected the properties of the PFS. Additionally, the prepared PFS polymerised coagulants exhibit a significantly better coagulation performance than the respective non-polymerised one, i.e. ferric sulphate.

Assessing the neuroprotective benefits for babies of antenatal magnesium sulphate: An individual participant data meta-analysis.

Directory of Open Access Journals (Sweden)

Caroline A Crowther

2017-10-01

Full Text Available Babies born preterm are at an increased risk of dying in the first weeks of life, and those who survive have a higher rate of cerebral palsy (CP compared with babies born at term. The aim of this individual participant data (IPD meta-analysis (MA was to assess the effects of antenatal magnesium sulphate, compared with no magnesium treatment, given to women at risk of preterm birth on important maternal and fetal outcomes, including survival free of CP, and whether effects differed by participant or treatment characteristics such as the reason the woman was at risk of preterm birth, why treatment was given, the gestational age at which magnesium sulphate treatment was received, or the dose and timing of the administration of magnesium sulphate.Trials in which women considered at risk of preterm birth (<37 weeks' gestation were randomised to magnesium sulphate or control treatment and where neurologic outcomes for the baby were reported were eligible for inclusion. The primary outcomes were infant death or CP and severe maternal outcome potentially related to treatment. Studies were identified based on the Cochrane Pregnancy and Childbirth search strategy using the terms [antenatal or prenatal] and [magnesium] and [preterm or premature or neuroprotection or 'cerebral palsy']. The date of the last search was 28 February 2017. IPD were sought from investigators with eligible trials. Risk of bias was assessed using criteria from the Cochrane Collaboration. For each prespecified outcome, IPD were analysed using a 1-stage approach. All 5 trials identified were included, with 5,493 women and 6,131 babies. Overall, there was no clear effect of magnesium sulphate treatment compared with no treatment on the primary infant composite outcome of death or CP (relative risk [RR] 0.94, 95% confidence interval (CI 0.85 to 1.05, 6,131 babies, 5 trials, p = 0.07 for heterogeneity of treatment effect across trials. In the prespecified sensitivity analysis restricted

Recovery of uranium from sulphate solutions containing molybdenum

International Nuclear Information System (INIS)

Weir, D.R.; Genik-Sas-Berezowsky, R.M.

1983-01-01

A process for recovering uranium from a sulphate solution containing dissolved uranium and molybdenum includes reacting the solution with ammonia (pH 8 to 10), the pH of the original solution must not exceed 5.5 and after the addition of ammonia the pH must not be in the vicinity of 7 for a significant time. The resultant uranium precipitate is relatively uncontaminated by molybdenum. The precipitate is then separated from the remaining solution while the pH is maintained within the stated range

Biosedimentary and geochemical constraints on the precipitation of mineral crusts in shallow sulphate lakes

Science.gov (United States)

Cabestrero, Óscar; del Buey, Pablo; Sanz-Montero, M. Esther

2018-04-01

Seasonal desiccation of Mg2+-(Na+)-(Ca2+)-SO42--(Cl-) saline lakes in La Mancha (Central Spain) that host microbial mats led to the precipitation of hydrated Na-Mg sulphates and gypsum. Sulphates precipitated in the submerged conditions form extensive biolaminites, whilst in marginal areas they produce thin crusts. Sedimentological, mineralogical, petrographic and high resolution textural studies reveal that the crusts were formed within the benthic microbial mats that thrive at salinities ranging from 160 to 340 g·L-1. The minerals of the crusts are primary bloedite (Na2Mg(SO4)2·4H2O), epsomite (MgSO4·7H2O), gypsum (CaSO4·2H2O) and mirabilite (Na2SO4·10H2O), as well as secondary hexahydrite (MgSO4·6H2O) and thenardite (Na2SO4). Primary bloedite crystals, which form the framework of surficial and submerged crusts are seen to nucleate subaqueously and grow incorporatively within the matgrounds. Displacive and incorporative epsomite grows on previous bloedite crystals and also on the ground. Mirabilite is precipitated rapidly at the brine-air interface over bloedite and epsomite. Hexahydrite and thenardite are formed due to dehydration of epsomite and mirabilite, respectively. Hydrochemical modeling with PHREEQC indicated that evaporitic biolaminites are forming from brines undersaturated with respect to bloedite, epsomite and mirabilite, which suggests that the microorganisms contribute to the heterogeneous nucleation of the sulphates in the microbial mats. Unlike carbonates, the influence of microbes on the growth and morphology of complicated double salts such as bloedite has not been documented previously and provides a new perspective on the formation of hydrated sulphate minerals that are common on Earth as well as other planets.

Copper nitrate redispersion to arrive at highly active silica-supported copper catalysts

NARCIS (Netherlands)

Munnik, P.|info:eu-repo/dai/nl/328228524; Wolters, M.|info:eu-repo/dai/nl/304829560; Gabrielsson, A.; Pollington, S.D.; Headdock, G.; Bitter, J.H.|info:eu-repo/dai/nl/160581435; de Jongh, P.E.|info:eu-repo/dai/nl/186125372; de Jong, K.P.|info:eu-repo/dai/nl/06885580X

2011-01-01

In order to obtain copper catalysts with high dispersions at high copper loadings, the gas flow rate and gas composition was varied during calcination of silica gel impregnated with copper nitrate to a loading of 18 wt % of copper. Analysis by X-ray diffraction (XRD), N2O chemisorption, and

Copper economy in Chlamydomonas: Prioritized allocation and reallocation of copper to respiration vs. photosynthesis

Science.gov (United States)

Kropat, Janette; Gallaher, Sean D.; Urzica, Eugen I.; Nakamoto, Stacie S.; Strenkert, Daniela; Tottey, Stephen; Mason, Andrew Z.; Merchant, Sabeeha S.

2015-01-01

Inorganic elements, although required only in trace amounts, permit life and primary productivity because of their functions in catalysis. Every organism has a minimal requirement of each metal based on the intracellular abundance of proteins that use inorganic cofactors, but elemental sparing mechanisms can reduce this quota. A well-studied copper-sparing mechanism that operates in microalgae faced with copper deficiency is the replacement of the abundant copper protein plastocyanin with a heme-containing substitute, cytochrome (Cyt) c6. This switch, which is dependent on a copper-sensing transcription factor, copper response regulator 1 (CRR1), dramatically reduces the copper quota. We show here that in a situation of marginal copper availability, copper is preferentially allocated from plastocyanin, whose function is dispensable, to other more critical copper-dependent enzymes like Cyt oxidase and a ferroxidase. In the absence of an extracellular source, copper allocation to Cyt oxidase includes CRR1-dependent proteolysis of plastocyanin and quantitative recycling of the copper cofactor from plastocyanin to Cyt oxidase. Transcriptome profiling identifies a gene encoding a Zn-metalloprotease, as a candidate effecting copper recycling. One reason for the retention of genes encoding both plastocyanin and Cyt c6 in algal and cyanobacterial genomes might be because plastocyanin provides a competitive advantage in copper-depleted environments as a ready source of copper. PMID:25646490

Chromium content in human skin after in vitro application of ordinary cement and ferrous-sulphate-reduced cement

DEFF Research Database (Denmark)

Fullerton, A; Gammelgaard, Bente; Avnstorp, C

1993-01-01

The amount of chromium found in human skin after in vitro application of cement suspensions on full-thickness human skin in diffusion cells was investigated. Cement suspensions made from ordinary Portland cement or Portland cement with the chromate reduced with added ferrous sulphate were used....... The cement suspensions were either applied on the skin surface under occlusion for 48 h or applied repeatedly every 24 h for 96 h. No statistically significant difference in chromium content of skin layers between skin exposed to ordinary Portland cement, skin exposed to cement with added ferrous sulphate...... and unexposed skin was observed, despite a more permeable skin barrier at the alkaline pH of the cement suspensions, i.e., pH 12.5. Increased chromium levels in epidermis and dermis were seen when ordinary Portland cement was applied as a suspension with added sodium sulphate (20%) on the skin surface for 96 h...

Exacerbation of alopecia areata: A possible complication of sodium tetradecyl sulphate foam sclerotherapy treatment for varicose veins.

Science.gov (United States)

Whiteley, Mark S; Smith, Victoria C

2017-01-01

A 40-year-old woman with a history of alopecia areata related to stress or hormonal changes was treated for bilateral primary symptomatic varicose veins (CEAP clinical score C2S) of pelvic origin, using a staged procedure. Her first procedure entailed pelvic vein embolisation of three pelvic veins using 14 coils and including foam sclerotherapy of the tributaries, using 3% sodium tetradecyl sulphate. Following this procedure, she had an exacerbation of alopecia areata with some moderate shedding of hair. Subsequently, she underwent endovenous laser ablation under local anaesthetic without incident. Seven months after the pelvic vein embolisation, she underwent foam sclerotherapy of leg and labial varicose veins using sodium tetradecyl sulphate. Two days following this procedure, she had a severe exacerbation of alopecia areata with gross shedding of hair. These two episodes of exacerbation of alopecia areata appear to be associated with sodium tetradecyl sulphate foam sclerotherapy of veins.

Evaluation of a single-dose of intravenous magnesium sulphate for prevention of postoperative pain after inguinal surgery

Directory of Open Access Journals (Sweden)

Shashi Kiran

2011-01-01

Full Text Available This study was undertaken to study efficacy of single dose of intravenous magnesium sulphate to reduce post-operative pain in patients undergoing inguinal surgery. One hundred patients undergoing inguinal surgery were divided randomly in two groups of 50 each. The patients of magnesium sulphate group (Group-I received magnesium sulphate 50 mg/kg in 250 ml of isotonic sodium chloride solution IV whereas patients in control group (Group-II received same volume of isotonic sodium chloride over 30 minutes preoperatively. Anaesthesia was induced with propofol (2 mg/kg and pethidine (1 mg/kg. Atracurium besylate (0.5 mg/kg was given to facilitate insertion of LMA. Pain at emergence from anaesthesia and 2, 4, 6, 12 and 24 hours after surgery was evaluated. The timing and dosage of rescue analgesic during first 24 hrs after operation was noted. Pain in postop period was significantly lower in magnesium sulphate group in comparison to control group at emergence from anaesthesia and 2, 4, 6, 12 and 24 hrs postop [1.86 vs. 1.96 (P=0.138, 1.22 vs. 1.82 (P=0.001, 1.32 vs. 1.88 (P=0.000, 2.74 vs. 3.84 (P=0.000, 1.36 vs. 2.00 (P=0.000 and 0.78 vs 1.30 (P=0.000, respectively]. Patients in group-I were more sedated as compared to group-II [sedation score 1.86 vs. 1.40 (P=0.000]. Rescue analgesia requirement postoperatively in first 4, 8 and 16 hrs was significantly lower in patients of group-1 than in group- II [1.9 vs. 3.8 (P<0.05, 25.50 vs. 52.50 (P<0.05 and 0.000 vs. 7.5 (P<0.05]. Preoperative magnesium sulphate infusion decreases postop pain and requirement of rescue analgesia.

Sulphate and desertification signals in Middle Eastern temperature trends

International Nuclear Information System (INIS)

Nasrallah, H.A.; Balling, R.C. Jr.

1994-01-01

Analysis of Middle Eastern annual temperature anomalies over the past 40 years reveals statistically significant warming over this time period of 0.07 C per decade. The warming is most pronounced over the spring season and least apparent in the winter season. Spatial analysis reveals a positive relationship between Middle Eastern warming and the degree of human-induced desertification and a negative relationship between local warming and the atmospheric concentration of sulphate

Canine Copper-Associated Hepatitis

NARCIS (Netherlands)

Dirksen, Karen; Fieten, Hille

2017-01-01

Copper-associated hepatitis is recognized with increasing frequency in dogs. The disease is characterized by centrolobular hepatic copper accumulation, leading to hepatitis and eventually cirrhosis. The only way to establish the diagnosis is by histologic assessment of copper distribution and copper

Fundamental Studies on the Electrochemical Behaviour of Carbon Steel Exposed in Sulphide and Sulphate-Reducing Environments

DEFF Research Database (Denmark)

Hilbert, Lisbeth Rischel

The aim of the report is to give a fundamental understanding of the response of different electrochemical techniques on carbon steel in a sulphide environment as well as in a biologically active sulphate-reducing environment (SRB). This will form the basis for further studies and for recommendati......The aim of the report is to give a fundamental understanding of the response of different electrochemical techniques on carbon steel in a sulphide environment as well as in a biologically active sulphate-reducing environment (SRB). This will form the basis for further studies...

Earth's copper resources estimated from tectonic diffusion of porphyry copper deposits

Science.gov (United States)

Kesler, Stephen E.; Wilkinson, Bruce H.

2008-03-01

Improved estimates of global mineral endowments are relevantto issues ranging from strategic planning to global geochemicalcycling. We have used a time-space model for the tectonic migrationof porphyry copper deposits vertically through the crust tocalculate Earth's endowment of copper in mineral deposits. Themodel relies only on knowledge of numbers and ages of porphyrycopper deposits, Earth's most widespread and important sourceof copper, in order to estimate numbers of eroded and preserveddeposits in the crust. Model results indicate that 125,895 porphyrycopper deposits were formed during Phanerozoic time, that only47,789 of these remain at various crustal depths, and that thesecontain 1.7 x 1011 tonnes (t) of copper. Assuming that othertypes of copper deposits behave similarly in the crust and haveabundances proportional to their current global production yieldsan estimate of 3 x 1011 t for total global copper resourcesat all levels in Earth's crust. Thus, 0.25% of the copper inthe crust has been concentrated into deposits through Phanerozoictime, and about two-thirds of this has been recycled by upliftand erosion. The amount of copper in deposits above 3.3 km,a likely limit of future mining, could supply current worldmine production for 5500 yr, thus quantifying the highly unusualand nonrenewable nature of mineral deposits.

Dose-dependent effect of homoeopathic drug Zinc sulphate on plant growth using Bacopa monnieri as model system

Directory of Open Access Journals (Sweden)

Vivek Kumar Gupta

2014-01-01

Full Text Available Background: Zinc is one of the essential micronutrients in plants required in very low quantity for plant growth and development. In higher concentration, it is known to to reduce the rate of photosynthesis, So homoeopathic preparations tested to see it role on plan growth. Objective: To analyse the effect of homoeopathic preparation of Zinc sulphate on plants through in-vitro assay using Bacopa monnieri as a model plant system. Materials and Methods: Six homoeopathic potencies (1X to 6X of Zinc sulphate were used on a decimal scale along with the control (MS basal agar medium. The samples were evaluated by adding fixed amount (100 μl in the media as well as by dipping the explants in the test sample overnight. At the completion of the incubation period (14 days the fresh and dry weight, number and length of the roots, number and length of the shoots and the number of leaves were analysed. Results: It was observed that Zinc sulphate showed growth inhibition at potencies from 1X to 5X, whereas at potency 6X, it exhibited growth promotion effect, when compared with the control. Conclusion: Homoeopathic drug (Zinc sulphate exhibited growth promotion at higher potency (6X and growth inhibition at lower potencies (1X to 5X on Bacopa monneiri.

Isolation and characterisation of barium sulphate and titanium oxides in monument crusts

Energy Technology Data Exchange (ETDEWEB)

Luis Perez-Rodriguez, Jose; Carmen Jimenez de Haro, Maria del; Maqueda, Celia

2004-10-25

Black crusts from historical ornamental materials contain Ba and Ti. These elements are in low proportion, making their determination difficult and especially the characterisation of the phases in which they are present. For this reason, works on the mineralogical composition of the two elements in black crusts is scarce. Thus the isolation, previous to their characterisation, is important for the study of the surface layer in altered monuments. An acid attack for the isolation of barium sulphate and titanium oxides in black crusts from polluted areas has been used. The acid employed is a mixture of HF, HNO{sub 3} and HClO{sub 4}. The residue isolated by acid attack was analysed by energy dispersive X-ray fluorescence and X-ray diffraction. It was characterised, and the percentages of barite (barium sulphate), anatase (titanium oxide), and rutile (titanium oxide) phases present in the surface layers were calculated.

Extraction of sulphates by long chain amines; Extraction des sulfates par les amines a longues chaines

Energy Technology Data Exchange (ETDEWEB)

Boirie, Ch [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1959-05-15

The extraction of sulphuric acid by long chain amines in organic solution has been studied with a view to determining the value of the stability constants of the amine sulphates and bi-sulphates formed. We have concentrated chiefly on uranium sulphate and thorium sulphate. The formulae of the complexes extractable with amines have been established, as well as the corresponding dissociation constants. We have observed that for uranium sulphate the formula of the complex depends only on the nature of the amine, whereas for thorium this formula varies with the amine structure. From the formulae determined and the value of the constants calculated, we have been able to establish the best conditions for uranium and thorium extraction and also for a separation of these two elements. Finally we propose an application of this study to the determination of uranium in ores, where the separation of uranium by this method is particularly easy and complete. (author) [French] L'extraction de l'acide sulfurique par des amines a longues chaines en solution organique a ete etudiee en vue de la determination de la valeur des constantes de stabilite des sulfates et bisulfates d'amines formes. Parmi les sulfates, nous nous sommes particulierement interesses au sulfate d'uranium et au sulfate de thorium. Nous avons determine les formules des complexes extractibles avec les amines, ainsi que les constantes de dissociation correspondantes. Nous avons remarque que pour le sulfate d'uranium, la formule du complexe ne depend que de la nature de l'amine, alors que pour le thorium cette formule varie avec la structure de l'amine. Les formules determinees et la valeur des constantes calculees, nous ont permis de decrire les meilleures conditions d'extraction de l'uranium et du thorium ainsi que celles d'une separation de ces deux elements. Nous proposons enfin une application de cette etude au dosage de l'uranium dans les minerais, ou la separation de l'uranium par cette methode est

Experimental Consequences of Mottness in High-Temperature Copper-Oxide Superconductors

Science.gov (United States)

Chakraborty, Shiladitya

2009-01-01

It has been more than two decades since the copper-oxide high temperature superconductors were discovered. However, building a satisfactory theoretical framework to study these compounds still remains one of the major challenges in condensed matter physics. In addition to the mechanism of superconductivity, understanding the properties of the…

Stage specific effects of soluble copper and copper oxide nanoparticles during sea urchin embryo development and their relation to intracellular copper uptake.

Science.gov (United States)

Torres-Duarte, Cristina; Ramos-Torres, Karla M; Rahimoff, René; Cherr, Gary N

2017-08-01

The effects of exposure to either soluble copper (copper sulfate) or copper oxide nanoparticles (nano-CuO) during specific early developmental stages of sea urchin embryos were analyzed. Soluble copper caused significant malformations in embryos (skeletal malformations, delayed development or gut malformations) when present at any given stage, while cleavage stage was the most sensitive to nano-CuO exposure causing skeletal malformations and decreased total antioxidant capacity. The stage specificity was linked to higher endocytic activity during the first hours of development that leads to higher accumulation of copper in specific cells critical for development. Results indicate that nano-CuO results in higher accumulation of copper inside of embryos and this intracellular copper is more persistent as compared to soluble copper. The possible implications later in development are discussed. Copyright © 2017 Elsevier B.V. All rights reserved.

Governing the Extractive Sector: The Politics of Globalisation and Copper Policy in Chile

Directory of Open Access Journals (Sweden)

Jewellord T. Nem Singh

2010-09-01

Full Text Available Chile exhibits an immense continuity in its copper policy and the sector’s reliable output contributes enormously to the tax revenues of the state. Copper in Chile is thus an interesting case because it challenges the presumed failure of neoliberal reforms in Latin America. It does this in a number of different ways. First, the sector is a clear success in terms of its output and contribution to GDP. Second, private capital and foreign direct investment in particular plays a critical role in developing the mining sector. Third, state- owned CODELCO has stood firmly against multinational companies. And fourth, Chile simultaneously exhibits a stability of rules inherited from Pinochet’s neoliberalism; labour relations characterised by conflict and co-optation; and a depoliticised mode of governance marked by copper policy technopols and an indirect link between copper and social policy. This paper argues that the Chilean state under La Concertación government has played an important ‘steering’ role by defusing the various political conflicts, contradictions and tensions in copper policy.

Genome Sequences of Two Copper-Resistant Escherichia coli Strains Isolated from Copper-Fed Pigs

DEFF Research Database (Denmark)

Lüthje, Freja L.; Hasman, Henrik; Aarestrup, Frank Møller

2014-01-01

The draft genome sequences of two copper-resistant Escherichia coli strains were determined. These had been isolated from copper-fed pigs and contained additional putative operons conferring copper and other metal and metalloid resistances.......The draft genome sequences of two copper-resistant Escherichia coli strains were determined. These had been isolated from copper-fed pigs and contained additional putative operons conferring copper and other metal and metalloid resistances....

Effects of preoperative magnesium sulphate on post-cesarean pain, a placebo controlled double blind study.

Directory of Open Access Journals (Sweden)

Seyed Mohamad Mireskandari

2015-03-01

Full Text Available To study the role of preoperative intravenous magnesium sulphate in decreasing post-cesarean pain and opioid requirement during first 24hrs.In a double blind randomized clinical trial, prior to induction of general anesthesia, fifty elective cesarean candidates were randomly assigned to one of the two groups of placebo or magnesium sulfate. After surgery visual analogue scale (VAS and infused morphine by PCA during 24 hrs were recorded. The data were analyzed by mann-Whitney -test, analysis of variance, and student t- test.VAS was significantly lower among patients in the magnesium sulphate group at intervals of 1(st, 6(th & 12(th hours after cesarean section (C/S with the mean scales of (48.9 ± 19.6 VS 74.7 ± 18.4, (42.1 ± 0.9 VS 58.3 ± 16.5 and (25.2 ± 6.1VS 30 ± 8.1 respectively and p-value of <0.001, 0.002 and 0.05 respectively. However at 24 hrs there was no significant difference in VAS with mean VAS scales of 22.6 ± 4.5 VS 23.6 ± 4.9 and p-value of 0.49. The dose of infused Morphine during 24 hrs was significantly less in the magnesium sulphate group than the placebo group with the means of 4.36 ± 1.4 VS 7.02 ± 1.9 mg respectively (p < 0.001.Administration of bolus 50 mg/kg magnesium sulphate prior to induction of general anesthesia may significantly decreased the morphine requirement during immediate post operative period and can be recommended as one of the modalities of post-operative pain control in the pregnant patients.

Interaction of aconitine with bovine serum albumin and effect of atropine sulphate and glycyrrhizic acid on the binding

International Nuclear Information System (INIS)

Huang Yun; Cui Lijian; Wang Jianming; Huo Kun; Chen Chen; Zhan Wenhong; Wang Yongli

2012-01-01

The interaction of aconitine with bovine serum albumin (BSA) and effect of atropine sulphate and glycyrrhizic acid on binding constant, binding sites, and conformation were studied in an aqueous buffer solution (pH 7.40) by ultraviolet absorption and fluorescence spectroscopy. The study results show that aconitine quenched the endogenous fluorescence of BSA via a dynamic quenching procedure. Predominant intermolecular forces between aconitine and BSA were hydrophobic interactions, which stabilized the complex of aconitine–BSA. The distance between the donor and acceptor was 2.62 nm. The conformation of BSA was investigated by synchronous fluorescence techniques, indicating that the microenvironment around tryptophan (Trp) residues was changed. Furthermore, with the addition of atropine sulphate or glycyrrhizic acid, binding constant and the number of binding sites of aconitine to BSA were decreased, and the conformation had no change, which provide an important theoretical support for aconitine detoxification by atropine sulphate and glycyrrhizic acid. - Highlights: ► Effect of atropine or glycyrrhizic acid on aconitine–BSA binding. ► UV–vis absorption and fluorescence spectroscopic techniques used. ► Aconitine quenched BSA fluorescence via dynamic quenching with r=2.62 nm. ► Atropine sulphate and glycyrrhizic acid decreased K A and n of aconitine–BSA. ► Support for aconitine detoxification by atropine and glycyrrhizic acid.

Copper uptake and retention in liver parenchymal cells isolated from nutritionally copper-deficient rats

NARCIS (Netherlands)

Berg, van den G.J.; de Goeij, J.J.M.; Bock, I.; Gijbels, M.J.J.; Brouwer, A.; Lei, K.Y.; Hendriks, H.F.J.

1991-01-01

Copper uptake and retention were studied in primary cultures of liver parenchymal cells isolated from copper-deficient rats. Male Sprague-Dawley rats were fed a copper-deficient diet (<1 mg Cu/kg) for 10 wk. Copper-deficient rats were characterized by low copper concentrations in plasma and liver,

Copper uptake and retention in liver parenchymal cells isolated from nutritionally copper-deficient rats

NARCIS (Netherlands)

Berg, G.J. van den; Goeij, J.J.M. de; Bock, I.; Gijbels, M.J.J.; Brouwer, A.; Lei, K.Y.; Hendruiks, H.F.J.

1991-01-01

Copper uptake and retention were studied in primary cultures of liver parenchymal cells isolated from copper-deficient rats. Male Sprague-Dawley rats were fed a copper-deficient diet (< 1 mg Cu/kg) for 10 wk. Copper-deficient rats were characterized by low copper concentrations in plasma and liver,

An improved assay for iduronate 2-sulphate sulphatase in serum and its use in the detection of carriers of the Hunter syndrome

International Nuclear Information System (INIS)

Archer, I.M.; Harper, P.S.; Wusteman, F.S.

1981-01-01

A more sensitive assay procedure has been developed for the enzyme iduronate 2-sulphate sulphatase which is deficient in the Hunter syndrome. The substrate is O-(α-L-idopyranosyluronic acid 2-sulphate)-(1 → 4)-2,5 anhydro-D-[ 3 H-1)mannitol 6-sulphate, which, after incubation, is separated from the product by ion-exchange chromatography on a micro-columnn of Dowex 1 X 2 (Cl - ). Serum analyses can be used to supplement those on hair roots in the detection of carriers of the Hunter syndrome. (Auth.)

COMPARATIVE STUDY OF EFFICACY OF FERROUS SULPHATE AND CARBONYL IRON IN ANEMIA OF ANTENATAL WOMEN

Directory of Open Access Journals (Sweden)

Radhika

2015-03-01

Full Text Available Iron deficiency anemia is the most common and important public health problem all over the world in the risk group of antenatal women. Research is going on to improve the iron status of the pregnant women with different forms of iron available. In this regard, Carbonyl Iron is showing promising results in improving the red cell mass with better compliance. 120 antenatal women were recruited in this study. The study comprised of 6weeks for each patient. They were given Carbonyl Iron 100 mg/day and FeS04 100gm/day . Before and after treatment all the baseline and specific investigations were one. Results were tabulated, comparison and significance were tested by unpaired student ’s’ test and their 'p' value was calculated. Results were shown graphically also. Carbonyl Iron showed improvement in hemoglobin, PCV and better than ferrous Sulphate (P <0.001. Incidence of side effects were less with Carbonyl Iron than Ferrous Sulphate, better compliance was seen with Carbonyl Iron. In conclusion, the present study s howed that Carbonyl Iron had better efficacy and safety in the management of Iron deficiency anemia in antenatal women than ferrous Sulphate

Annual Copper Mountain Conferences on Multigrid and Iterative Methods, Copper Mountain, Colorado

International Nuclear Information System (INIS)

McCormick, Stephen F.

2016-01-01

This project supported the Copper Mountain Conference on Multigrid and Iterative Methods, held from 2007 to 2015, at Copper Mountain, Colorado. The subject of the Copper Mountain Conference Series alternated between Multigrid Methods in odd-numbered years and Iterative Methods in even-numbered years. Begun in 1983, the Series represents an important forum for the exchange of ideas in these two closely related fields. This report describes the Copper Mountain Conference on Multigrid and Iterative Methods, 2007-2015. Information on the conference series is available at http://grandmaster.colorado.edu/~copper/

Annual Copper Mountain Conferences on Multigrid and Iterative Methods, Copper Mountain, Colorado

Energy Technology Data Exchange (ETDEWEB)

McCormick, Stephen F. [Front Range Scientific, Inc., Lake City, CO (United States)

2016-03-25

This project supported the Copper Mountain Conference on Multigrid and Iterative Methods, held from 2007 to 2015, at Copper Mountain, Colorado. The subject of the Copper Mountain Conference Series alternated between Multigrid Methods in odd-numbered years and Iterative Methods in even-numbered years. Begun in 1983, the Series represents an important forum for the exchange of ideas in these two closely related fields. This report describes the Copper Mountain Conference on Multigrid and Iterative Methods, 2007-2015. Information on the conference series is available at http://grandmaster.colorado.edu/~copper/.

Modification degrees at specific sites on heparan sulphate: an approach to measure chemical modifications on biological molecules with stable isotope labelling

Science.gov (United States)

Wu, Zhengliang L.; Lech, Miroslaw

2005-01-01

Chemical modification of biological molecules is a general mechanism for cellular regulation. A quantitative approach has been developed to measure the extent of modification on HS (heparan sulphates). Sulphation on HS by sulphotransferases leads to variable sulphation levels, which allows cells to tune their affinities to various extracellular proteins, including growth factors. With stable isotope labelling and HPLC-coupled MS, modification degrees at various O-sulphation sites could be determined. A bovine kidney HS sample was first saturated in vitro with 34S by an OST (O-sulphotransferase), then digested with nitrous acid and analysed with HPLC-coupled MS. The 34S-labelled oligosaccharides were identified based on their unique isotope clusters. The modification degrees at the sulphotransferase recognition sites were obtained by calculating the intensities of isotopic peaks in the isotope clusters. The modification degrees at 3-OST-1 and 6-OST-1 sites were examined in detail. This approach can also be used to study other types of chemical modifications on biological molecules. PMID:15743272

An 131I iodotamoxifen: no carrier added iodination via a diazonium salt

International Nuclear Information System (INIS)

Hunter, D.H.; Strickland, L.A.

1986-01-01

An 131 I-labeled iodotamoxifen has been prepared by a ''no carrier added'' procedure in a 40% radiochemical yield via an aryl diazonium ion salt intermediate. Two approaches were used to produce high specific activity iodotamoxifen: nonaqueous solvents and copper catalysis. The use of the nonaqueous solvent acetonitrile has proved successful while neither copper powder, copper-bronze, copper(I)oxide nor Cu(II) sulphate showed any catalytic effects. (author)

Alternative substrates of bacterial sulphate reduction suitable for the biological-chemical treatment of acid mine drainage

Directory of Open Access Journals (Sweden)

Alena Luptakova

2012-12-01

Full Text Available The impacts of AMD pollution on biological systems are mostly severe and the problem may persist from many decadesto thousands of years. Consequently AMD prior to being released into the environment must be treated to meet government standardsfor the amount of metal and non-metal ions contained in the water. One of the best available technologies for the removal of metals fromAMD is precipitation as metal sulphides. SRB applications for AMD treatment involve a few principal stages. The first stageis the cultivation of SRB i.e. the bacterial sulphate reduction. At the laboratory conditions the sodium lactate is the energetic substratefor the growth of bacteria. Its price is not economic for the application in the practice and is needed investigate the alternativesubstitutes. The aim of this work was the cultivation of SRB using the selected energetic substrates such as: calcium lactate, ethanol,saccharose, glucose and whey. Experimental studies confirm that in the regard to the amount of reduced sulphates the calcium lactateand ethanol are the best alternative substrates for the bacterial sulphate-reduction.

Exacerbation of alopecia areata: A possible complication of sodium tetradecyl sulphate foam sclerotherapy treatment for varicose veins

Directory of Open Access Journals (Sweden)

Mark S Whiteley

2017-05-01

Full Text Available A 40-year-old woman with a history of alopecia areata related to stress or hormonal changes was treated for bilateral primary symptomatic varicose veins (CEAP clinical score C2S of pelvic origin, using a staged procedure. Her first procedure entailed pelvic vein embolisation of three pelvic veins using 14 coils and including foam sclerotherapy of the tributaries, using 3% sodium tetradecyl sulphate. Following this procedure, she had an exacerbation of alopecia areata with some moderate shedding of hair. Subsequently, she underwent endovenous laser ablation under local anaesthetic without incident. Seven months after the pelvic vein embolisation, she underwent foam sclerotherapy of leg and labial varicose veins using sodium tetradecyl sulphate. Two days following this procedure, she had a severe exacerbation of alopecia areata with gross shedding of hair. These two episodes of exacerbation of alopecia areata appear to be associated with sodium tetradecyl sulphate foam sclerotherapy of veins.

Focus on CSIR research in pollution waste: Cellulose degradation, volatile fatty acid formation and biological sulphate removal operating and anaerobic hybrid reactor

CSIR Research Space (South Africa)

Greben, H

2007-08-01

Full Text Available The biological sulphate removal technology requires carbon and energy sources to reduce sulphate to sulphide. Plant biomass, e.g. cut grass, is a sustainable source of energy when cellulose is utilised in the anaerobic degradation to produce...

Nearly 60% Copper Rod & Wire Companies Neutral about Future Copper Price

Institute of Scientific and Technical Information of China (English)

2012-01-01

<正>How about the trend of copper price recently? According to the survey result of Shanghai Metals Market, amongst 21 domestic copper rod & wire companies, 57% of the companies are neutral about the future copper price, while 14% and 19% of the companies consider that

Effect of high levels of dietary molybdenum and sulphate on SA ...

African Journals Online (AJOL)

1988-10-29

Oct 29, 1988 ... The concentrations of plasma copper in groups. M and MS were higher than that of the control group in both the ewes and the rams. In the case of group C, the concentration of TCA-soluble plasma copper represented about 95% of the total plasma copper compared to 65% in the case of groups M and MS.

In vitro propagation of Calla lily: adenine sulphate and 6-benzilaminopurine

Directory of Open Access Journals (Sweden)

Márcia De Nazaré Oliveira Ribeiro

2014-09-01

Full Text Available Calla lily [Zantedeschia aethiopica (L. Spreng.] belonging to the Araceae family is appreciated as cut flower and in com­position of gardens. However, the conventional propagation of this plants shows a poor productive. Thus, tissue culture besides allowing fast clonal propagation also provides healthy and uniforms plants. The aim was study the influence of the differents concentrations of 6-benzilaminopurine (BAP and adenine sulphate (AS on in vitro multiplication of Calla lily. The explants were maintained in MS medium added with BAP (0.0, 8.9, 17.8 and 26.7 μM and adenine sulphate (0, 54, 108 and 162 μM. The plants were transferred to growth room and maintained at 25±1ºC and photoperiod of 16 hours for 60 days, under luminous intensity of 35 μmol m-2 s-1, for a period of 60 days. The experimental design was entirely randomized with four repetitions of three seedlings each, resulting in twelve plants per treatment, each tube with one plant. The statistics analysis showed interactive effects for quantify of BAP and AS for leaves number and fresh mass of the aerial parts. The highest number of leaves (4.8 and fresh mass of aerial parts (0.73 g was obtained with 26.7 μM of BAP combined with 108 μM of AS, highest number of shoots (2.6 was obtained with 22,19 μM of BAP and highest lengh of sprouts (5.0 cm was observed in the absence of BAP. The addition of BAP increased the number of shoots per explant. The use of adenine sulphate in combination with BAP had a positive effect for the accumulation of fresh weight and number of leaves in vitro culture.

EFFECT OF PRETREATMENT WITH MAGNESIUM SULPHATE ON SUCCINYLCHOLINEINDUCED FASCICULATIONS AND MYALGIA

Directory of Open Access Journals (Sweden)

Astha Raman

2016-12-01

Full Text Available BACKGROUND Succinylcholine, a depolarising muscle relaxant possesses a unique property of rapid onset and short duration of action, but is accompanied by side effects such as fasciculations and myalgia. A prospective randomised-controlled trial was designed to assess the effect of a combination of magnesium sulphate with propofol for induction of anaesthesia on succinylcholine-induced fasciculations and myalgia. MATERIALS AND METHODS 60 adult patients of ASA status I and II of both sexes for elective surgery under general anaesthesia were randomly allocated into two equal groups, group MG and group NS. The patients of MG group were pretreated with magnesium sulphate 40 mg/kg body weight in 10 mL volume, while patients of NS group were given isotonic saline 0.9% in the same volume (10 mL intravenously slowly over a period of 10 mins. Anaesthesia was administered with pentazocine 0.6 mg/kg and propofol 2 mg/kg, followed by administration of succinylcholine 2 mg/kg intravenously. Muscle fasciculations were observed and graded as nil, mild, moderate or severe. Postoperative myalgia was assessed after 24 hrs. of surgery and graded as nil, mild, moderate or severe. Observations were made in double blind manner where the observer and the patient were blinded. RESULTS Demographic data and baseline parameters of both groups were comparable (P>0.05. Muscle fasciculations occurred in 66.7% patients of MG group versus 100% patients of NS group with a significant difference (P<0.001. After 24 hrs. of surgery, 12 patients of MG group and 28 patients of NS group had myalgia with a significant difference (P<0.001. Statistically significant difference was found in MAP and heart rate at various intervals between the two groups (P<0.001. CONCLUSION Magnesium sulphate 40 mg/kg intravenously maybe used with propofol for induction of anaesthesia to control succinylcholineinduced fasciculations and myalgia.

A Cooperative Copper Metal-Organic Framework-Hydrogel System Improves Wound Healing in Diabetes.

Science.gov (United States)

Xiao, Jisheng; Chen, Siyu; Yi, Ji; Zhang, Hao; Ameer, Guillermo A

2017-01-05

Chronic non-healing wounds remain a major clinical challenge that would benefit from the development of advanced, regenerative dressings that promote wound closure within a clinically relevant time frame. The use of copper ions has shown promise in wound healing applications possibly by promoting angiogenesis. However, reported treatments that use copper ions require multiple applications of copper salts or oxides to the wound bed, exposing the patient to potentially toxic levels of copper ions and resulting in variable outcomes. Herein we set out to assess whether copper metal organic framework nanoparticles (HKUST-1 NPs) embedded within an antioxidant thermoresponsive citrate-based hydrogel would decrease copper ion toxicity and accelerate wound healing in diabetic mice. HKUST-1 and poly-(polyethyleneglycol citrate-co- N -isopropylacrylamide) (PPCN) were synthesized and characterized. HKUST-1 NP stability in a protein solution with and without embedding them in PPCN hydrogel was determined. Copper ion release, cytotoxicity, apoptosis, and in vitro migration processes were measured. Wound closure rates and wound blood perfusion were assessed in vivo using the splinted excisional dermal wound diabetic mouse model. HKUST-1 NP disintegrated in protein solution while HKUST-1 NPs embedded in PPCN (H-HKUST-1) were protected from degradation and copper ions were slowly released. Cytotoxicity and apoptosis due to copper ion release were significantly reduced while dermal cell migration in vitro and wound closure rates in vivo were significantly enhanced. In vivo , H-HKUST-1 induced angiogenesis, collagen deposition, and re-epithelialization during wound healing in diabetic mice. These results suggest that a cooperatively stabilized, copper ion-releasing H-HKUST-1 hydrogel is a promising innovative dressing for the treatment of chronic wounds.

Remote C−H Activation of Quinolines through Copper-Catalyzed Radical Cross-Coupling

KAUST Repository

Xu, Jun; Shen, Chao; Zhu, Xiaolei; Zhang, Pengfei; Ajitha, Manjaly John; Huang, Kuo-Wei; An, Zhongfu; Liu, Xiaogang

2016-01-01

Achieving site selectivity in carbon-hydrogen (C-H) functionalization reactions is a formidable challenge in organic chemistry. Herein, we report a novel approach to activating remote C-H bonds at the C5 position of 8-aminoquinoline through copper

In Situ Production of Copper Oxide Nanoparticles in a Binary Molten Salt for Concentrated Solar Power Plant Applications.

Science.gov (United States)

Lasfargues, Mathieu; Stead, Graham; Amjad, Muhammad; Ding, Yulong; Wen, Dongsheng

2017-05-19

Seeding nanoparticles in molten salts has been shown recently as a promising way to improve their thermo-physical properties. The prospect of such technology is of interest to both academic and industrial sectors in order to enhance the specific heat capacity of molten salt. The latter is used in concentrated solar power plants as both heat transfer fluid and sensible storage. This work explores the feasibility of producing and dispersing nanoparticles with a novel one pot synthesis method. Using such a method, CuO nanoparticles were produced in situ via the decomposition of copper sulphate pentahydrate in a KNO₃-NaNO₃ binary salt. Analyses of the results suggested preferential disposition of atoms around produced nanoparticles in the molten salt. Thermal characterization of the produced nano-salt suspension indicated the dependence of the specific heat enhancement on particle morphology and distribution within the salts.

Evidence for biological activity in mineralization of secondary sulphate deposits in a basaltic environment: implications for the search for life in the Martian subsurface

Science.gov (United States)