WorldWideScience

Sample records for copper silicates

  1. Facile synthesis of magnetic hierarchical copper silicate hollow nanotubes for efficient adsorption and removal of hemoglobin.

    Science.gov (United States)

    Zhang, Min; Wang, Baoyu; Zhang, Yanwei; Li, Weizhen; Gan, Wenjun; Xu, Jingli

    2016-01-21

    This study reports the fabrication of magnetic copper silicate hierarchical hollow nanotubes, which are featured by a tailored complex wall structure and high surface area. Moreover, they exhibit excellent performance as an easily recycled adsorbent for protein separation. Particularly, this strategy can be extended as a general method to prepare other magnetic metal silicate hollow nanotubes.

  2. [Influence of EPS on silicate corrosion inhibition for copper pipe in soft water].

    Science.gov (United States)

    Li, Shi-Yin

    2008-10-01

    The effects of sodium alginate on silicate corrosion inhibition for copper pipe in simulated soft water were investigated. The results showed that more soluble copper release was occurred when low concentration sodium alginate was in presence. The 1 a aged copper pipe released more soluble copper than the 3 a and 10 a aged copper pipe. The sequence of concentration of soluble copper release was c 1 a > c 3 a, > c 10 a. However, compared to the low concentration sodium alginate, soluble copper released from the 1 a aged copper pipe increased, and the 3 a and 10 a aged copper pipe were inverse when high level sodium alginate was in presence. These phenomena showed that the effect of silicate corrosion inhibition decreased when extracellular polymer substances was dissolved in soft water. Under the conditions of pH 7.5 and sodium alginate 16 mg/L, soluble copper release tend was gradually increase-decrease-gradually run-up which due to the absorption of sodium alginate on the surface of copper surface and the complex interaction between sodium alginate, silicate and copper ions. When the initial pH value was low, compared to the system of no sodium alginate, the soluble copper release distinctly increased in the presence of sodium alginate. The amount of soluble copper released from 1 a copper pipe is higher than that from 3 a and 10 a aged copper pipe, which due to the different components of copper corrosion by-products on the surface of different aged copper pipes and the different solubility of different corrosion by-products.

  3. Statistical modeling of copper losses in the silicate slag of the sulfide concentrate smelting process

    OpenAIRE

    2015-01-01

    This article presents the results of the statistical modeling of copper losses in the silicate slag of the sulfide concentrates smelting process. The aim of this study was to define the correlation dependence of the degree of copper losses in the silicate slag on the following parameters of technological processes: SiO2, FeO, Fe3O4, CaO and Al2O3 content in the slag and copper content in the matte. Multiple linear regression analysis (MLRA), artificial neural networks (ANNs) and adaptive netw...

  4. Phase analytical studies of industrial copper smelting slags. Part I: Silicate slags

    Science.gov (United States)

    Rüffler, R.; Dávalos, J.

    1998-12-01

    The pyrometallurgical extraction of copper from sulfide ore concentrates is determined by the behaviour of the associated iron during smelting. Hence, 57Fe Mössbauer spectroscopy is an attractive tool for studying the phases in silicate slags from German and Chilean smelting plants. Other methods used were ore microscopy, electron microprobe analysis, and X-ray powder diffraction.

  5. Statistical modeling of copper losses in the silicate slag of the sulfide concentrate smelting process

    Directory of Open Access Journals (Sweden)

    Savic Marija V.

    2015-09-01

    Full Text Available This article presents the results of the statistical modeling of copper losses in the silicate slag of the sulfide concentrates smelting process. The aim of this study was to define the correlation dependence of the degree of copper losses in the silicate slag on the following parameters of technological processes: SiO2, FeO, Fe3O4, CaO and Al2O3 content in the slag and copper content in the matte. Multiple linear regression analysis (MLRA, artificial neural networks (ANNs and adaptive network based fuzzy inference system (ANFIS were used as tools for mathematical analysis of the indicated problem. The best correlation coefficient (R2 = 0.719 of the final model was obtained using the ANFIS modeling approach.

  6. Raman signature modification induced by copper nanoparticles in silicate glass

    OpenAIRE

    2005-01-01

    International audience; Composite materials formed by metal nanoclusters embedded in glasses/glazes have been produced for centuries (Roman hematinum and Renaissance alassonti, Coptic lustre-painted glass and Islamic lustre ceramics). Comparisons were drawn from Raman analyses of alkali borosilicate glasses coloured by copper as “blue” Cu2+ (peak absorption at 750 nm), as “colourless” Cu+, and as “opaque red” Cu0 (peak absorptions at ~420 and 570 nm). In particular, Raman analyses of copper-r...

  7. A vibrational spectroscopic study of the copper bearing silicate mineral luddenite.

    Science.gov (United States)

    Frost, Ray L; López, Andrés; Xi, Yunfei; Scholz, Ricardo

    2015-02-25

    The molecular structure of the copper-lead silicate mineral luddenite has been analysed using vibrational spectroscopy. The mineral is only one of many silicate minerals containing copper. The intense Raman band at 978 cm(-1) is assigned to the ν1 (A1g) symmetric stretching vibration of Si5O14 units. Raman bands at 1122, 1148 and 1160 cm(-1) are attributed to the ν3 SiO4 antisymmetric stretching vibrations. The bands in the 678-799 cm(-1) are assigned to OSiO bending modes of the (SiO3)n chains. Raman bands at 3317 and 3329 cm(-1) are attributed to water stretching bands. Bands at 3595 and 3629 cm(-1) are associated with the stretching vibrations of hydroxyl units suggesting that hydroxyl units exist in the structure of luddenite.

  8. A thermodynamic study of silica-saturated iron silicate slags in equilibrium with liquid copper

    Science.gov (United States)

    Oishi, Toshio; Kamuo, Morinori; Ono, Katsutoshi; Moriyama, Joichiro

    1983-03-01

    The thermodynamic properties of silica-saturated iron silicate slags in equilibrium with liquid copper have been studied from oxygen partial pressure measurements in the temperature range from 1490 to 1580 K by means of a solid electrolyte galvanic cell. The following cells were used: Pt, Ni-NiO/O=/slag-Cu(l), Cr2O3, Pt; Pt, Fe-FeO/O=/slag-Cu(Fe sat.), Fe. A strong correlation was found between oxygen pressure and the copper content of the slag; the copper content increased from less than 1 pct near iron saturation to about 4 pct at an oxygen partial pressure of 7.2 x 10-3 Pa. A similar correlation was found between the ferric iron/total iron ratio and the oxygen pressure. The oxygen content in liquid copper decreased with increasing iron content in liquid copper and increased slightly near iron saturation. This behavior could be explained qualitatively by using the standard free energy of formation of FeO and the activities of components.

  9. Facile synthesis and properties of hierarchical double-walled copper silicate hollow nanofibers assembled by nanotubes.

    Science.gov (United States)

    Jin, Renxi; Yang, Yang; Xing, Yan; Chen, Li; Song, Shuyan; Jin, Rongchao

    2014-04-22

    The hierarchical assembly of multilevel, nonspherical hollow structures remains a considerable challenge. Here, we report a facile approach for synthesizing copper silicate hollow nanofibers with an ultrasmall nanotube-assembled, double-walled structure. The as-prepared hollow fibers possess a tailored complex wall structure, high length-to-diameter ratio, good structural stability, and a high surface area, and they exhibit excellent performance as an easily recycled adsorbent for wastewater treatment and as an ideal support for noble metal catalysts. In addition, this strategy can be extended as a general approach to prepare other double-walled, hollow, fibrous silica-templated materials.

  10. Occurrence mechanism of silicate and aluminosilicate minerals in Sarcheshmeh copper flotation concentrate

    Institute of Scientific and Technical Information of China (English)

    H.R. Barkhordari; E. Jorjani; A. Eslami; M. Noaparast

    2009-01-01

    The Sarcheshmeh copper flotation circuit is producing 5×10~4 t copper concentrate per month with an averaging grade of 28% Cu in rougher, cleaner and reeleaner stages. In recent years, with the increase in the open pit depth, the content of aluminosili- cate minerals increased in plant feed and subsequently in flotation concentrate. It can motivate some problems, such as unwanted consumption of reagents, decreasing of the copper concentrate grade, increasing of Al_2O_3 and SiO_2 in the copper concentrate, and needing a higher temperature in the smelting process. The evaluation of the composite samples related to the most critical working period of the plant shows that quartz, illite, biotite, chlorite, orthoclase, albeit, muscovite, and kaolinite are the major Al_2O_3 and SiO_2 beating minerals that accompany chalcopyrite, chalcoeite, and covellite minerals in the plant feed. The severe alteration to clay min-erals was a general rule in all thin sections that were prepared from the plant feed. Sieve analysis of the flotation concentrate shows that Al_2O_3 and SiO_2 bearing minerals in the flotation concentrate can be decreased by promoting the size reduction from 53 to 38 μm. Interlocking of the Al_2O_3 and SiO_2 beating minerals with ehalcopyrite and ehalcocite is the occurrence mechanism of silicate and aluminosilicate minerals in the flotation concentrate. The dispersed form of interlocking is predominant.

  11. Preparation of magnetic carbon nanotubes with hierarchical copper silicate nanostructure for efficient adsorption and removal of hemoglobin

    Science.gov (United States)

    Zhang, Min; Wang, Yongtao; Zhang, Yanwei; Ding, Lei; Zheng, Jing; Xu, Jingli

    2016-07-01

    The controllable synthesis of materials with the desired structure and dimensionality is of great significance in material science. In this work, the hierarchical CNTs/Fe3O4@copper silicate (CNTs/Fe3O4@CuSilicate) composites were synthesized via a simple chemical conversion route by using CNTs/Fe3O4@SiO2 nanocables as template. Firstly, magnetic CNTs composites (CNTs/Fe3O4) were synthesized by the high temperature decomposition process using the iron acetylacetonate as raw materials. Then a layer of SiO2 can be easily coated on the magnetic CNTs by the stöber method, which were then converted into CNTs/Fe3O4@CuSilicate composites by hydrothermal reaction between the silica shell and copper ions in alkaline solution. The resulting CNTs/Fe3O4@CuSilicate composites hold merits such as magnetic responsivity, good dispersibility, and large specific surface area. Moreover, the CNTs/Fe3O4@copper silicate composites have strong affinity toward bovine hemoglobin (BHb), which were successfully applied to convenient, efficient, and fast removal of abundant proteins (HHb and HSA) in human blood.

  12. Identification of the man-made barium copper silicate pigments among some ancient Chinese artifacts through spectroscopic analysis.

    Science.gov (United States)

    Li, Q H; Yang, J C; Li, L; Dong, J Q; Zhao, H X; Liu, S

    2015-03-05

    This article describes the complementary application of non-invasive micro-Raman spectroscopy and energy dispersive X-ray fluorescence spectrometry to the characterization of some ancient Chinese silicate artifacts. A total of 28 samples dated from fourth century BC to third century AD were analyzed. The results of chemical analysis showed that the vitreous PbO-BaO-SiO2 material was used to sinter these silicate artifacts. The barium copper silicate pigments including BaCuSi4O10, BaCuSi2O6 and BaCu2Si2O7 were widely identified from colorful areas of the samples by Raman spectroscopy. In addition, other crystalline phases such as Fe2O3, BaSi2O5, BaSO4, PbCO3 and quartz were also identified. The present study provides very valuable information to trace the technical evolution of man-made barium copper silicate pigments and their close relationship with the making of ancient PbO-BaO-SiO2 glaze and glass.

  13. HRTEM/AEM study of trace metal behavior, sheet silicate reactions, and fluid/solid mass balances in porphyry copper hydrothermal systems

    Energy Technology Data Exchange (ETDEWEB)

    Veblen, D.R.; Ilton, E.S.

    1989-04-01

    Transmission electron microscopy has been used to investigate copper (Cu) incorporation into silicates and alteration reactions in porphyry copper deposits. High Cu in biotites results from submicroscopic inclusions of native Cu. The incorporation of Cu in low-temperature alteration lamellae suggests that Cu enrichment occurs during weathering, rather than during the hydrothermal event. Drill core from Cyprus Casa Grande, Arizona, shows systematic variation of Cu in sheet silicates as a function of depth in the weathering column. The aims of the present project are to apply the powerful techniques of transmission electron microscopy (TEM), high-resolution TEM (HRTEM), and analytical electron microscopy (AEM) to understanding the geochemical processes in porphyry copper systems at the near-atomic scale. Our primary goals are to characterize the structural state of anomalously high Cu in silicates, determine the timing and conditions of Cu enrichment in silicates such as biotite, and use these data to suggest how base metals are released and subsequently immobilized under hydrothermal or weathering conditions; and to determine the submicroscopic, atomic-level reaction mechanisms responsible for silicate alteration in porphyry-copper hydrothermal systems, which will allow us to determine reaction stoichiometries and hence mass balances between minerals and hydrothermal fluid. 19 refs., 7 figs., 3 tabs.

  14. Synthesis and microwave absorption properties of yolk-shell microspheres with magnetic iron oxide cores and hierarchical copper silicate shells.

    Science.gov (United States)

    Liu, Jiwei; Cheng, Jin; Che, Renchao; Xu, Junjie; Liu, Mengmei; Liu, Zhengwang

    2013-04-10

    Yolk-shell microspheres with magnetic Fe3O4 cores and hierarchical copper silicate shells have been successfully synthesized by combining the versatile sol-gel process and hydrothermal reaction. Various yolk-shell microspheres with different core size and shell thickness can be readily synthesized by varying the experimental conditions. Compared to pure Fe3O4, the as-synthesized yolk-shell microspheres exhibit significantly enhanced microwave absorption properties in terms of both the maximum reflection loss value and the absorption bandwidth. The maximum reflection loss value of these yolk-shell microspheres can reach -23.5 dB at 7 GHz with a thickness of 2 mm, and the absorption bandwidths with reflection loss lower than -10 dB are up to 10.4 GHz. Owing to the large specific surface area, high porosity, and synergistic effect of both the magnetic Fe3O4 cores and hierarchical copper silicate shells, these unique yolk-shell microspheres may have the potential as high-efficient absorbers for microwave absorption applications.

  15. Enhanced ionic conductivity of apatite-type lanthanum silicate electrolyte for IT-SOFCs through copper doping

    Science.gov (United States)

    Ding, Xifeng; Hua, Guixiang; Ding, Dong; Zhu, Wenliang; Wang, Hongjin

    2016-02-01

    Apatite-type Lanthanum silicate (LSO) is among the most promising electrolyte for intermediate temperature solid oxide fuel cells (IT-SOFCs) owing to the high conductivity and low activation energy at lower temperature than traditional doped-zirconia electrolyte. The ionic conductivity as well as the sintering density of lanthanum silicate oxy-apatite, La10Si6-xCuxO27-δ (LSCO, 0 ≤ x ≤ 2), was effectively enhanced through a small amount of doped copper. The phase composition, relative density, ionic conductivity and thermal expansion behavior of La10Si6-xCuxO27-δ was systematically investigated by X-ray diffraction (XRD), Archimedes' drainage method, scanning electron microscope (SEM), electrochemical impedance spectra (EIS) and thermal dilatometer techniques. With increasing copper doping content, the ionic conductivity of La10Si6-xCuxO27-δincreased, reaching a maximum of 4.8 × 10-2 S cm-1 at 800 °C for x = 1.5. The improved ionic conductivity could be primarily associated with the enhanced grain conductivity. The power output performance of NiO-LSCO/LSCO/LSCF single cell was superior to that obtained on NiO-LSO/LSO/LSCF at different temperatures using hydrogen as fuel and oxygen as oxidant, which could be attributed to the enhanced oxygen ionic conductivity as well as the sintering density for the copped doped lanthanum silicate. In conclusion, the apatite La10Si4.5Cu1.5O25.5 is a promising candidate electrolyte for IT-SOFCs.

  16. The influence of the silicate slag composition on copper losses during smelting of the sulfide concentrates

    Directory of Open Access Journals (Sweden)

    Živković Živan

    2009-01-01

    Full Text Available This paper presents the results of multi-linear regression analysis (MLRA of the slag composition (SiO2, FeO, Fe3O4, CaO, Al2O3 and the content of copper in the matte on resulting copper content in the slag during smelting of the sulfide concentrates in the reverberatory furnace. When comparing results obtained with MLRA model calculations with values measured at industrial level high degree of fitting is obtained (R2 = 0.974. This indicates that slag composition and content of copper in the matte influences the copper losses in the waste slag with the probability of 95 %.

  17. The influence of the silicate slag composition on copper losses during smelting of the sulfide concentrates

    OpenAIRE

    2009-01-01

    This paper presents the results of multi-linear regression analysis (MLRA) of the slag composition (SiO2, FeO, Fe3O4, CaO, Al2O3) and the content of copper in the matte on resulting copper content in the slag during smelting of the sulfide concentrates in the reverberatory furnace. When comparing results obtained with MLRA model calculations with values measured at industrial level high degree of fitting is obtained (R2 = 0.974). This indicates that slag composition and content of copper in t...

  18. In Vitro susceptibility of methicillin-resistant Staphylococcus aureus and methicillin-susceptible Staphylococcus aureus to a new antimicrobial, copper silicate.

    Science.gov (United States)

    Carson, Kerry C; Bartlett, Jessica G; Tan, Trina-Jean; Riley, Thomas V

    2007-12-01

    The soluble copper silicate (CS) MIC of 100 strains of methicillin-resistant Staphylococcus aureus and 100 strains of methicillin-susceptible S. aureus (MSSA) was 175 mg Cu/liter. Bactericidal and postantibiotic effects (> or =1 h) were seen at 2x MIC and 4x MIC. The frequency of mutation was <10(-9), and serial passage could not extend growth beyond 1.6x MIC.

  19. Distribution of Precious Metals (Ag, Au, Pd, Pt, and Rh) Between Copper Matte and Iron Silicate Slag

    Science.gov (United States)

    Avarmaa, Katri; Johto, Hannu; Taskinen, Pekka

    2016-02-01

    The distributions of precious metals (Ag, Au, Pd, Pt, and Rh) between copper matte and silica-saturated iron silicate slag were determined at 1523 K to 1623 K (1250 °C to 1350 °C), in controlled CO-CO2-SO2-Ar gas mixtures. The experiments were done in silica crucibles and a fixed partial pressure of sulfur dioxide for matte grades of 55, 65, and 75 wt pct Cu. High-temperature equilibration/quenching/electron probe X-ray microanalysis technique was used to obtain compositions of the equilibrated matte and slag. The technique was applied for the first time to the distributions of precious metals in simulated flash smelting conditions. The resolution of electron probe microanalysis became critical as the detection limits were insufficient to measure reliably the precious metals concentrations (except silver) in the slag. The distribution coefficient of silver, L m/s[Ag] = [wt pctAg in matte]/(wt pctAg in slag), was found to be between 200 and 300, which agrees well with the latest studies in the literature. For other precious metals, the minimum values of distribution coefficients were determined according to the detection limits in the slag. The values obtained were for gold and platinum >250, for palladium >1000, and for rhodium >900. The distribution coefficients of palladium, although locating above distribution coefficient of the detection limit, formed a clear dependency with a good repeatability as a function of the matte grade. It increased along with matte grade and was approximately 1000 at 50 pct Cu and 2000 to 3000 at 70 pct Cu. The precious metals replace metal in the matte structure and they are present as sulfides in the copper matte.

  20. Copper-ion-assisted self-assembly of silicate clays in rod- and disklike morphologies.

    Science.gov (United States)

    Tsai, Wei-Cheng; Lin, Jiang-Jen

    2010-06-15

    Self-assembled rodlike (0.3-2.5 microm in diameter and 5.3-31 microm in length) and disklike microstructures (1.8-10.6 microm in width and 0.1-1.0 microm in thickness) are uniquely present in amorphous clay aggregates. Clay units were prepared by intercalation of Na(+)-montmorillonite (Na(+)-MMT) with copper ions (Cu(2+)) and poly(oxypropylene)-amine salt (POP) in simultaneous or stepwise ionic exchange reactions. Differences in process control during incorporation of Cu(2+) and hydrophobic POP greatly affected the layer structure of the clay units (d spacing of 12-53 A) and consequently their amphiphilic dispersion properties. By controlling the dispersion in water and drying at 80 degrees C, highly ordered self-assembly structures were obtained, presumably as a result of self-piling of clay units in competing vertical and horizontal directions. In general, association with Cu(2+) yielded units with a disklike microstructure, in contrast to the rod-like structure obtained for POP-intercalated clay. The self-assembled structures were characterized using X-ray diffraction, UV adsorption, thermal gravimetric analysis, zeta potential, scanning electron microscopy, and energy-dispersive X-ray spectroscopy techniques. Control of the clay self-piling process provides a new synthetic route for the fabrication of bottom-up microstructures that are potentially useful for templates, sensors, and electronic devices.

  1. The dehydrated copper silicate Na(2)[Cu(2)Si(4)O(11)]: a three-dimensional microporous framework with a linear Si-O-Si linkage.

    Science.gov (United States)

    Cunha-Silva, Luís; Brandão, Paula; Rocha, João; Almeida Paz, Filipe A

    2008-01-23

    The structure of the title dehydrated copper silicate, disodium dicopper undeca-oxide tetra-silicate, Na(2)(Cu(2)O(11)Si(4)), was determined by single-crystal X-ray diffraction from a non-merohedral twin. It exhibits an effective three-dimensional microporous framework with the major channels, in which the Na(+) cations are placed, running along the a-axis direction and smaller channels observed along the b-axis direction. The structure is unusual in that it contains a symmetry-constrained Si-O-Si angle of 180°. The Cu centre is coordinated to five O atoms, exhibiting a slightly distorted square-pyramidal coordination geometry. The Na cation is interacting with five neighbouring O atoms, exhibiting an uncharacteristic coordination environment.

  2. The dehydrated copper silicate Na2[Cu2Si4O11]: a three-dimensional microporous framework with a linear Si—O—Si linkage

    OpenAIRE

    2008-01-01

    The structure of the title dehydrated copper silicate, disodium dicopper undecaoxide tetrasilicate, Na2(Cu2O11Si4), was determined by single-crystal X-ray diffraction from a non-merohedral twin. It exhibits an effective three-dimensional microporous framework with the major channels, in which the Na+ cations are placed, running along the a-axis direction and smaller channels observed along the b-axis direction. The structure is unusual in that it contains a symmetry-constrained Si—OR...

  3. The dehydrated copper silicate Na2[Cu2Si4O11]: a three-dimensional microporous framework with a linear Si—O—Si linkage

    Directory of Open Access Journals (Sweden)

    Filipe A. Almeida Paz

    2008-02-01

    Full Text Available The structure of the title dehydrated copper silicate, disodium dicopper undecaoxide tetrasilicate, Na2(Cu2O11Si4, was determined by single-crystal X-ray diffraction from a non-merohedral twin. It exhibits an effective three-dimensional microporous framework with the major channels, in which the Na+ cations are placed, running along the a-axis direction and smaller channels observed along the b-axis direction. The structure is unusual in that it contains a symmetry-constrained Si—O—Si angle of 180°. The Cu centre is coordinated to five O atoms, exhibiting a slightly distorted square-pyramidal coordination geometry. The Na cation is interacting with five neighbouring O atoms, exhibiting an uncharacteristic coordination environment.

  4. Copper Silicate Hydrate Hollow Spheres Constructed by Nanotubes Encapsulated in Reduced Graphene Oxide as Long-Life Lithium-Ion Battery Anode.

    Science.gov (United States)

    Wei, Xiujuan; Tang, Chunjuan; Wang, Xuanpeng; Zhou, Liang; Wei, Qiulong; Yan, Mengyu; Sheng, Jinzhi; Hu, Ping; Wang, Bolun; Mai, Liqiang

    2015-12-09

    Hierarchical copper silicate hydrate hollow spheres-reduced graphene oxide (RGO) composite is successfully fabricated by a facile hydrothermal method using silica as in situ sacrificing template. The electrochemical performance of the composite as lithium-ion battery anode was studied for the first time. Benefiting from the synergistic effect of the hierarchical hollow structure and conductive RGO matrix, the composite exhibits excellent long-life performance and rate capability. A capacity of 890 mAh/g is achieved after 200 cycles at 200 mA/g and a capacity of 429 mAh/g is retained after 800 cycles at 1000 mA/g. The results indicate that the strategy of combining hierarchical hollow structures with conductive RGO holds the potential in addressing the volume expansion issue of high capacity anode materials.

  5. Removal of copper (II) from aqueous solutions by flotation using polyaluminum chloride silicate (PAX-XL60 S) as coagulant and carbonate ion as activator.

    Science.gov (United States)

    Ghazy, S E; Mahmoud, I A; Ragab, A H

    2006-01-01

    Flotation is a separation technology for removing toxic heavy metal ions from aqueous solutions. Here a simple and rapid flotation procedure is presented for the removal of copper(II) from aqueous solutions. It is based on the use of polyaluminum chloride silicate (PAX-XL60 S) as coagulant and flocculent, carbonate ion as activator and oleic acid (HOL) as surfactant. Both ion and precipitate flotation are included depending on the solution pH. Ion and precipitate flotation in the aqueous HOL-PAX-XL60 S-Cu2+-CO3(2-) system gave powerful preferential removal of Cu2+ (F -100%) over the HOL-PAX-XL60 S-Cu2+ system containing no CO3(2+) ion (F approximately 86%). The role of CO3(2-) ion is also evident from decreasing the dose of PAX-XL60 S from 700 mg l(-1) to 200 mg l(-1). The other parameters, influencing the flotation process, namely: metal ion, surfactant and PAX-XL60 S concentrations, ionic strength, temperature and foreign ions were examined. Moreover, the procedure was successfully applied to recover Cu2+ ions from different volumes up to 11 and from natural water samples.

  6. Simulation Synthesis of Ancient Chinese Artificial Barium Copper Silicate Pigments%中国古代人造硅酸铜钡颜料模拟制备研究

    Institute of Scientific and Technical Information of China (English)

    张治国; 马清林; 梅建军; 海因茨·贝克[德

    2012-01-01

    中国古代人造硅酸铜钡颜料主要包括三种,紫色的中国紫(BaCuSi2O6)、浅蓝色的中国蓝(BaCuShO10)和蓝色的中国深蓝(BaCu2Si2O7),这三种颜料在战国晚期至东汉晚期的中国大量使用。本文在对大量古代硅酸铜钡颜料样品分析研究的基础上,探讨了该类颜料的原料、烧制温度以及坩埚对模拟制备的影响。用石英粉作为硅源,铜绿和氧化铜作为铜源,硫酸钡、碳酸钡和氧化钡作为钡源,氧化铅作为铅源,模拟制备出了三种古代人造硅酸铜钡颜料,即中国紫(BaCuSi2O7)、中国蓝(BaCuShO10)和中国深蓝(BaCu2Si2O7)。%Ancient Chinese barium copper silicate pigments mainly comprise Chinese Purple (BaCuSi2O6), Chinese Blue (BaCuSi4O10) and Chinese Dark Blue (BaCu2Si2O7). They were widely used from the late Warring States period to the late Eastern Han Dynasty. Based on the analysis of large amounts of samples, this paper discusses the raw materials, firing temperature and crucible' s influence on the synthesis. The three pigments - BaeuSi2O6, BaCuSi4O10 and BaCu2Si2O7 - have been simulated by using quartz powder as silicon source, malachite and copper oxide as copper source, barium sulfate, barium carbonate and barium oxide as barium source, and lead oxide as lead source.

  7. Inhibiting Approaches of Magnesium Silicate Minerals in Copper-nickel Sulfide Ore Floatation%铜镍硫化矿浮选中镁质硅酸盐矿物的抑制途径

    Institute of Scientific and Technical Information of China (English)

    曹钊; 张亚辉; 孙传尧; 曹永丹

    2012-01-01

    分析了铜镍硫化矿中MgO脉石矿物的晶体结构、理化性质及其与可浮性的关系,总结了铜镍硫化矿浮选中含镁脉石矿物进入浮选精矿的可能途径及对策,着重介绍了含镁脉石矿物表面活化离子的作用及消除机理,最终得出采用高效金属离子络合剂对矿物表面进行清洗预处理,恢复矿物的原本浮游性,再用选择性抑制剂抑制含镁脉石矿物,将是处理含镁硅酸盐铜镍硫化矿物的有效途径的结论.%The relationship of crystal structure, physico-chemical properties and ftoatability of MgO-containing silicate gangue minerals in copper-nickel sulfide ores was analyzed, possible ways of magnesium silicate mixed into flotation concentrate in copper-nickel sulfids ores flotation and corresponding coun term easu res were summarized, the activating mechanism of metal ions on magnesium silicate and deactivating methods were emphatically researched. Finally an effective method was obtained. In this method, an efficient metal ions complexing agent is used to clean the surfaces of minerals, which will recover their original floatability. In the meantime, a selective depressant is applied to depress magnesium-containing gangue minerals. This may be the effective approach for depressing magnesium-containing silicate minerals in copper-nickel sulfide ore floatation.

  8. FORMATION OF TRICALCIUM SILICATE WITH DIFFERENT CONTENT OF COPPER OXIDE%不同氧化铜掺量下硅酸三钙矿物的形成

    Institute of Scientific and Technical Information of China (English)

    王培铭; 李好新; 吴建国

    2007-01-01

    The formation mechanism and polymorphisms of tricalcium silicate (C3S) with different mass fractions of CuO were studied by using differential scanning calorimetry, the scanning electron microscopy and phase equilibiria. The polymorphisms of C3S were differentiated with the X-ray diffraction. The experimental results show that adding small amounts of CuO could not affect the decomposition apparent activation energy of CaCO3 distinctly, but the addition of CuO provides liquid phase for the formation of C3S,and the main composition of liquid phase about (80%) is CuO. Furthermore, the CuO exerts a remarkable influence on the polymorphisms of C3S. The polymorphisms of C3S were triclinic for the samples with CuO content of 0, 1.0%, 1.5% and 2.0%. The polymorphism of C3S was rhombohedral for the sample with 0.5% CuO. The polymorphism of C3S was monoclinic for the sample with 3.0% CuO.%通过非等温差示扫描量热分析和扫描电子显微镜,结合CuO-CaO系统相图,研究CuO在CaCO3和SiO2混合物中的掺量(质量分数)对硅酸三钙(C3S)矿物形成机理的影响.用X射线衍射分析了最终烧制试样的多晶型组成.结果表明:在C3S矿物形成的过程中,少量CuO的加入并没有显著地影响到CaCO3分解表观活化能.但是CuO的加入为C3S矿物的形成提供了液相,增加了液相量,液相的主要成分约80%为CuO.CuO的加入对C3S矿物的晶型产生了显著的影响.当试样中掺入0,1.0%,1.5%,2.0%CuO时,C3S多相体为T型;当试样中掺入0.5%CuO时,C3S多相体为R型;当试样中掺入3%CuO时,C3S多相体为M型.

  9. Effect of copper-doped silicate 13–93 bioactive glass scaffolds on the response of MC3T3-E1 cells in vitro and on bone regeneration and angiogenesis in rat calvarial defects in vivo

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Yinan; Xiao, Wei [Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO 65409 (United States); Bal, B. Sonny [Department of Orthopaedic Surgery, University of Missouri, Columbia, MO 65212 (United States); Rahaman, Mohamed N., E-mail: rahaman@mst.edu [Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO 65409 (United States)

    2016-10-01

    The release of inorganic ions from biomaterials could provide an alternative approach to the use of growth factors for improving tissue healing. In the present study, the release of copper (Cu) ions from bioactive silicate (13–93) glass scaffolds on the response of cells in vitro and on bone regeneration and angiogenesis in vivo was studied. Scaffolds doped with varying concentrations of Cu (0–2.0 wt.% CuO) were created with a grid-like microstructure by robotic deposition. When immersed in simulated body fluid in vitro, the Cu-doped scaffolds released Cu ions into the medium in a dose-dependent manner and converted partially to hydroxyapatite. The proliferation and alkaline phosphatase activity of pre-osteoblastic MC3T3-E1 cells cultured on the scaffolds were not affected by 0.4 and 0.8 wt.% CuO in the glass but they were significantly reduced by 2.0 wt.% CuO. The percent new bone that infiltrated the scaffolds implanted for 6 weeks in rat calvarial defects (46 ± 8%) was not significantly affected by 0.4 or 0.8 wt.% CuO in the glass whereas it was significantly inhibited (0.8 ± 0.7%) in the scaffolds doped with 2.0 wt.% CuO. The area of new blood vessels in the fibrous tissue that infiltrated the scaffolds increased with CuO content of the glass and was significantly higher for the scaffolds doped with 2.0 wt.% CuO. Loading the scaffolds with bone morphogenetic protein-2 (1 μg/defect) significantly enhanced bone infiltration and reduced fibrous tissue in the scaffolds. These results showed that doping the 13–93 glass scaffolds with up to 0.8 wt.% CuO did not affect their biocompatibility whereas 2.0 wt.% CuO was toxic to cells and detrimental to bone regeneration. - Highlights: • First study to evaluate Cu ion release from silicate (13-93) bioactive glass scaffolds on osteogenesis in vivo • Released Cu ions influenced bone regeneration in a dose dependent manner • Lower concentrations of Cu ions had little effect on bone regeneration • Cu ion

  10. Effect of copper-doped silicate 13-93 bioactive glass scaffolds on the response of MC3T3-E1 cells in vitro and on bone regeneration and angiogenesis in rat calvarial defects in vivo.

    Science.gov (United States)

    Lin, Yinan; Xiao, Wei; Bal, B Sonny; Rahaman, Mohamed N

    2016-10-01

    The release of inorganic ions from biomaterials could provide an alternative approach to the use of growth factors for improving tissue healing. In the present study, the release of copper (Cu) ions from bioactive silicate (13-93) glass scaffolds on the response of cells in vitro and on bone regeneration and angiogenesis in vivo was studied. Scaffolds doped with varying concentrations of Cu (0-2.0wt.% CuO) were created with a grid-like microstructure by robotic deposition. When immersed in simulated body fluid in vitro, the Cu-doped scaffolds released Cu ions into the medium in a dose-dependent manner and converted partially to hydroxyapatite. The proliferation and alkaline phosphatase activity of pre-osteoblastic MC3T3-E1 cells cultured on the scaffolds were not affected by 0.4 and 0.8wt.% CuO in the glass but they were significantly reduced by 2.0wt.% CuO. The percent new bone that infiltrated the scaffolds implanted for 6weeks in rat calvarial defects (46±8%) was not significantly affected by 0.4 or 0.8wt.% CuO in the glass whereas it was significantly inhibited (0.8±0.7%) in the scaffolds doped with 2.0wt.% CuO. The area of new blood vessels in the fibrous tissue that infiltrated the scaffolds increased with CuO content of the glass and was significantly higher for the scaffolds doped with 2.0wt.% CuO. Loading the scaffolds with bone morphogenetic protein-2 (1μg/defect) significantly enhanced bone infiltration and reduced fibrous tissue in the scaffolds. These results showed that doping the 13-93 glass scaffolds with up to 0.8wt.% CuO did not affect their biocompatibility whereas 2.0wt.% CuO was toxic to cells and detrimental to bone regeneration.

  11. Nanostructured silicate polymer concrete

    Directory of Open Access Journals (Sweden)

    Figovskiy Oleg L'vovich

    2014-03-01

    Full Text Available It has been known that acid-resistant concretes on the liquid glass basis have high porosity (up to 18~20 %, low strength and insufficient water resistance. Significant increasing of silicate matrix strength and density was carried out by incorporation of special liquid organic alkali-soluble silicate additives, which block superficial pores and reduce concrete shrinkage deformation. It was demonstrated that introduction of tetrafurfuryloxisilane additive sharply increases strength, durability and shock resistance of silicate polymer concrete in aggressive media. The experiments showed, that the strength and density of silicate polymer concrete increase in case of decreasing liquid glass content. The authors obtained optimal content of silicate polymer concrete, which possesses increased strength, durability, density and crack-resistance. Diffusive permeability of concrete and its chemical resistance has been investigated in various corroding media.

  12. Polymer-Layer Silicate Nanocomposites

    DEFF Research Database (Denmark)

    Potarniche, Catalina-Gabriela

    Nowadays, some of the material challenges arise from a performance point of view as well as from recycling and biodegradability. Concerning these aspects, the development of polymer layered silicate nanocomposites can provide possible solutions. This study investigates how to obtain polymer layered...... silicate nanocomposites and their structure-properties relationship. In the first part of the thesis, thermoplastic layered silicates were obtained by extrusion. Different modification methods were tested to observe the intercalation treatment effect on the silicate-modifier interactions. The silicate...

  13. Silicic Large Igneous Provinces

    Institute of Scientific and Technical Information of China (English)

    Scott Bryan

    2007-01-01

    @@ Large Igneous Provinces (LIPs) are the end-product of huge additions of magma to the continental crust both at the surface and at depth. Since the first categorisation of LIPs by Coffin & Eldholm (1994), it has been recognised that LIPs are more varied inform, age and character, and this includes the recognition of Silicic LIPs. Silicic LIPs are the largest accumulations of primary volcaniclastic rocks at the Earth's surface with areal extents >0.1 Mkm2 and extrusive and subvolcanic intrusive volumes >0.25 Mkm3. The Late Palaeozoic to Cenozoic Silicic LIP events are the best recognised and are similar in terms of their dimension, crustal setting, volcanic architecture and geochemistry.

  14. Silicates in Alien Asteroids

    Science.gov (United States)

    2009-01-01

    This plot of data from NASA's Spitzer Space Telescopes shows that asteroid dust around a dead 'white dwarf' star contains silicates a common mineral on Earth. The data were taken primarily by Spitzer's infrared spectrograph, an instrument that breaks light apart into its basic constituents. The yellow dots show averaged data from the spectrograph, while the orange triangles show older data from Spitzer's infrared array camera. The white dwarf is called GD 40.

  15. Silicates in Alien Asteroids

    Science.gov (United States)

    2009-01-01

    This plot of data from NASA's Spitzer Space Telescopes shows that asteroid dust around a dead 'white dwarf' star contains silicates a common mineral on Earth. The data were taken primarily by Spitzer's infrared spectrograph, an instrument that breaks light apart into its basic constituents. The yellow dots show averaged data from the spectrograph, while the orange triangles show older data from Spitzer's infrared array camera. The white dwarf is called GD 40.

  16. Thermochemistry of Silicates

    Science.gov (United States)

    Costa, Gustavo; Jacobson, Nathan

    2015-01-01

    The thermodynamic properties of vapor and condensed phases of silicates are crucial in many fields of science. These quantities address fundamental questions on the formation, stability, transformation, and physical properties of silicate minerals and silicate coating compositions. Here the thermodynamic activities of silica and other species in solid solution have been measured by the analysis of the corresponding high temperature vapors using Knudsen Effusion Mass Spectrometry (KEMS). In first set of experiments KEMS has been used to examine the volatility sequence of species (Fe, SiO, Mg, O2 and O) present in the vapor phase during heating of fosterite-rich olivine (Fo93Fa7) up to 2400 C and to measure the Fe, SiO and Mg activities in its solid solution. The data of fosterite-rich olivine are essential for thermochemical equilibrium models to predict the atmospheric and surface composition of hot, rocky exoplanets (Lava Planets). In the second set of experiments the measured thermodynamic activities of the silica in Y2O3-SiO2 and Yb2O3-SiO2 systems are used to assess their reactivity and degradation recession as environmental barrier coatings (EBCs) in combustion environments (e.g. non-moveable parts of gas turbine engine).

  17. U.S. Geological Survey silicate rock standards

    Science.gov (United States)

    Flanagan, F.J.

    1967-01-01

    The U.S. Geological Survey has processed six silicate rocks to provide new reference samples to supplement G-1 and W-1. Complete conventional, rapid rock, and spectrochemical analyses by the U.S. Geological Survey are reported for a granite (replacement for G-1), a granodiorite, an andesite, a peridotite, a dunite, and a basalt. Analyses of variance for nickel, chromium, copper, and zirconium in each rock sample showed that for these elements, the rocks can be considered homogeneous. Spectrochemical estimates are given for the nickel, chromium, copper, and zirconium contents of the samples. The petrography of five of the six rocks is described and CIPW norms are presented. ?? 1967.

  18. Final report on the safety assessment of aluminum silicate, calcium silicate, magnesium aluminum silicate, magnesium silicate, magnesium trisilicate, sodium magnesium silicate, zirconium silicate, attapulgite, bentonite, Fuller's earth, hectorite, kaolin, lithium magnesium silicate, lithium magnesium sodium silicate, montmorillonite, pyrophyllite, and zeolite.

    Science.gov (United States)

    Elmore, Amy R

    2003-01-01

    This report reviews the safety of Aluminum, Calcium, Lithium Magnesium, Lithium Magnesium Sodium, Magnesium Aluminum, Magnesium, Sodium Magnesium, and Zirconium Silicates, Magnesium Trisilicate, Attapulgite, Bentonite, Fuller's Earth, Hectorite, Kaolin, Montmorillonite, Pyrophyllite, and Zeolite as used in cosmetic formulations. The common aspect of all these claylike ingredients is that they contain silicon, oxygen, and one or more metals. Many silicates occur naturally and are mined; yet others are produced synthetically. Typical cosmetic uses of silicates include abrasive, opacifying agent, viscosity-increasing agent, anticaking agent, emulsion stabilizer, binder, and suspending agent. Clay silicates (silicates containing water in their structure) primarily function as adsorbents, opacifiers, and viscosity-increasing agents. Pyrophyllite is also used as a colorant. The International Agency for Research on Cancer has ruled Attapulgite fibers >5 microm as possibly carcinogenic to humans, but fibers mining and processing of Aluminum Silicate, Calcium Silicate, Zirconium Silicate, Fuller's Earth, Kaolin, Montmorillonite, Pyrophyllite, and Zeolite. The Cosmetic Ingredient Review (CIR. The Cosmetic Ingredient Review (CIR) Expert Panel concluded that the extensive pulmonary damage in humans was the result of direct occupational inhalation of the dusts and noted that lesions seen in animals were affected by particle size, fiber length, and concentration. The Panel considers that most of the formulations are not respirable and of the preparations that are respirable, the concentration of the ingredient is very low. Even so, the Panel considered that any spray containing these solids should be formulated to minimize their inhalation. With this admonition to the cosmetics industry, the CIR Expert Panel concluded that these ingredients are safe as currently used in cosmetic formulations. The Panel did note that the cosmetic ingredient, Talc, is a hydrated magnesium silicate

  19. Environmental silicate nano-biocomposites

    CERN Document Server

    Pollet, Eric

    2012-01-01

    Environmental Silicate Nano-Biocomposites focuses on nano-biocomposites, which are obtained by the association of silicates such as bioclays with biopolymers. By highlighting recent developments and findings, green and biodegradable nano-composites from both renewable and biodegradable polymers are explored. This includes coverage of potential markets such as packaging, agricultures, leisure and the fast food industry. The knowledge and experience of more than twenty international experts in diverse fields, from chemical and biochemical engineering to applications, is brought together in four different sections covering: Biodegradable polymers and Silicates, Clay/Polyesters Nano-biocomposites, Clay/Agropolymers Nano-biocomposites, and Applications and biodegradation of Nano-biocomposites. By exploring the relationships between the biopolymer structures, the processes, and the final properties Environmental Silicate Nano-Biocomposites explains how to design nano-materials to develop new, valuable, environmenta...

  20. Copper hypersensitivity.

    Science.gov (United States)

    Fage, Simon W; Faurschou, Annesofie; Thyssen, Jacob P

    2014-10-01

    The world production of copper is steadily increasing. Although humans are widely exposed to copper-containing items on the skin and mucosa, allergic reactions to copper are only infrequently reported. To review the chemistry, biology and accessible data to clarify the implications of copper hypersensitivity, a database search of PubMed was performed with the following terms: copper, dermatitis, allergic contact dermatitis, contact hypersensitivity, contact sensitization, contact allergy, patch test, dental, IUD, epidemiology, clinical, and experimental. Human exposure to copper is relatively common. As a metal, it possesses many of the same qualities as nickel, which is a known strong sensitizer. Cumulative data on subjects with presumed related symptoms and/or suspected exposure showed that a weighted average of 3.8% had a positive patch test reaction to copper. We conclude that copper is a very weak sensitizer as compared with other metal compounds. However, in a few and selected cases, copper can result in clinically relevant allergic reactions.

  1. Stardust silicates from primitive meteorites.

    Science.gov (United States)

    Nagashima, Kazuhide; Krot, Alexander N; Yurimoto, Hisayoshi

    2004-04-29

    Primitive chondritic meteorites contain material (presolar grains), at the level of a few parts per million, that predates the formation of our Solar System. Astronomical observations and the chemical composition of the Sun both suggest that silicates must have been the dominant solids in the protoplanetary disk from which the planets of the Solar System formed, but no presolar silicates have been identified in chondrites. Here we report the in situ discovery of presolar silicate grains 0.1-1 microm in size in the matrices of two primitive carbonaceous chondrites. These grains are highly enriched in 17O (delta17O(SMOW) > 100-400 per thousand ), but have solar silicon isotopic compositions within analytical uncertainties, suggesting an origin in an oxygen-rich red giant or an asymptotic giant branch star. The estimated abundance of these presolar silicates (3-30 parts per million) is higher than reported for other types of presolar grains in meteorites, consistent with their ubiquity in the early Solar System, but is about two orders of magnitude lower than their abundance in anhydrous interplanetary dust particles. This result is best explained by the destruction of silicates during high-temperature processing in the solar nebula.

  2. Copper transport.

    Science.gov (United States)

    Linder, M C; Wooten, L; Cerveza, P; Cotton, S; Shulze, R; Lomeli, N

    1998-05-01

    In adult humans, the net absorption of dietary copper is approximately 1 mg/d. Dietary copper joins some 4-5 mg of endogenous copper flowing into the gastrointestinal tract through various digestive juices. Most of this copper returns to the circulation and to the tissues (including liver) that formed them. Much lower amounts of copper flow into and out of other major parts of the body (including heart, skeletal muscle, and brain). Newly absorbed copper is transported to body tissues in two phases, borne primarily by plasma protein carriers (albumin, transcuprein, and ceruloplasmin). In the first phase, copper goes from the intestine to the liver and kidney; in the second phase, copper usually goes from the liver (and perhaps also the kidney) to other organs. Ceruloplasmin plays a role in this second phase. Alternatively, liver copper can also exit via the bile, and in a form that is less easily reabsorbed. Copper is also present in and transported by other body fluids, including those bathing the brain and central nervous system and surrounding the fetus in the amniotic sac. Ceruloplasmin is present in these fluids and may also be involved in copper transport there. The concentrations of copper and ceruloplasmin in milk vary with lactational stage. Parallel changes occur in ceruloplasmin messenger RNA expression in the mammary gland (as determined in pigs). Copper in milk ceruloplasmin appears to be particularly available for absorption, at least in rats.

  3. Copper hypersensitivity

    DEFF Research Database (Denmark)

    Fage, Simon W; Faurschou, Annesofie; Thyssen, Jacob P

    2014-01-01

    hypersensitivity, a database search of PubMed was performed with the following terms: copper, dermatitis, allergic contact dermatitis, contact hypersensitivity, contact sensitization, contact allergy, patch test, dental, IUD, epidemiology, clinical, and experimental. Human exposure to copper is relatively common...

  4. NON-AUTOCLAVE SILICATE BRICK

    Directory of Open Access Journals (Sweden)

    V. N. Yaglov

    2015-01-01

    Full Text Available The paper proposes a technology for obtaining bricks on the basis of lime-silica mixtures where chemical interactions are practically completely realized in dispersive state at the stage of preparation of binding contact maturing and raw mixture as a whole. The role of forming operation (moulding is changed in principle because in this case conversion of dispersive system into a rock-like solid occurs and due to this the solid obtains complete water-resistance in contact with water immediately after forming operation. Theoretical basis for the developed technology is capability of silicate dispersive substances (hydrated calcium silicate to transit in non-stable state, to form a rock-like water-resistant solid in the moment of mechanical load application during forming process. Specific feature of the proposed method is an exclusion of additional operations for autoclaving of products from the process of obtaining a silicate brick.Synthetic hydrated calcium silicate in contrast to natural ones are more uniform in composition and structure, they contain less impurities and they are characterized by dispersive composition and due to the mentioned advantages they find wider practical application. Contact-condensation binders permit to manipulate product properties on their basis and ensure maximum correspondence to the requirements of the concrete application. Raw material sources for obtaining synthetic hydrated calcium silicates are practically un-limited because calcium-silicon containing substances are found as in various technogenic wastes so in natural compounds as well. So the problem for obtaining hydrated calcium silicates having contact-condensation ability for structure formation becomes more and more actual one. This transition is considered as dependent principally on arrangement rate of substance particles which determined the level of its instability.

  5. Reseach on Acid Leaching Processes of A Nickel-copper Laterite Silicate Ore From Qinghai%用硫酸从青海含铜红土型硅酸镍矿石浸出镍、铜试验研究

    Institute of Scientific and Technical Information of China (English)

    陈晓鸣; 张昱; 王春梅; 严鹏; 陈力行

    2014-01-01

    研究了青海某含铜红土型硅酸镍矿石的常压和加压酸浸。试验结果表明:对于常压酸浸,在磨矿粒度-0.15 mm占95%、硫酸用量80%、浸出温度90℃、液固质量比2.3∶1、浸出时间3 h条件下,镍、铜浸出率分别为86.8%和92.6%;对于加压酸浸,在磨矿细度-0.15 mm占95%、硫酸用量60%、浸出温度120℃、液固体积质量比1.5∶1、浸出时间2h条件下,镍、铜浸出率分别为92.4%和94.0%。常压酸浸与加压酸浸均可得到较高的金属浸出率,但加压酸浸效率更高,且对杂质金属铁的浸出有一定抑制作用。%T he comparison tests for atmosphere leaching and pressure leaching of a nickel-copper laterite silicate ore from Qinghai were conducted .The results showed that both atmosphere leaching and pressure leaching can gain high leaching rate .At the conditions of atmosphere ,temperature of 90℃ ,ore granularity of -100 mesh accounting for 95% ,acid usage of 800 kg/t ores ,pulp density of 30% and agitation time of 3 h ,the leaching rate of Ni and Cu is 86 .8% and 92 .6% ,respectively .While at the conditions of pressure (202 kPa ) ,temperature of 120 ℃ ,ore granularity of - 100 mesh accounting for 95% ,acid usage of 600 kg/t ores ,pulp density of 40% ,and agitation leaching time of 2h ,the leaching rate of Ni and Cu is 92 .4% and 94 .0% ,respectively .However ,compared with the atmosphere leaching ,the pressure leaching can gain a higher leaching rate ,w hat is more important that it would have some inhibiting effect for Fe leaching .

  6. Direct Production of Copper

    Science.gov (United States)

    Victorovich, G. S.; Bell, M. C.; Diaz, C. M.; Bell, J. A. E.

    1987-09-01

    The use of commercially pure oxygen in flash smelting a typical chalcopyrite concentrate or a low grade comminuted matte directly to copper produces a large excess of heat. The heat balance is controlled by adjusting the calorific value of the solid feed. A portion of the sulfide material is roasted to produce a calcine which is blended with unroasted material, and the blend is then autogeneously smelted with oxygen and flux directly to copper. Either iron silicate or iron calcareous slags are produced, both being subject to a slag cleaning treatment. Practically all of the sulfur is contained in a continuous stream of SO2 gas, most of which is strong enough for liquefaction. A particularly attractive feature of these technologies is that no radically new metallurgical equipment needs to be developed. The oxygen smelting can be carried out not only in the Inco type flash furnace but in other suitable smelters such as cyclone furnaces. Another major advantage stems from abolishion of the ever-troublesome converter aisle, which is replaced with continuous roasting of a fraction of the copper sulfide feed.

  7. Hydrothermal Formation of Calcium Copper Tetrasilicate.

    Science.gov (United States)

    Johnson-McDaniel, Darrah; Comer, Sara; Kolis, Joseph W; Salguero, Tina T

    2015-12-01

    We describe the first hydrothermal synthesis of CaCuSi4 O10 as micron-scale clusters of thin platelets, distinct from morphologies generated under salt-flux or solid-state conditions. The hydrothermal reaction conditions are surprisingly specific: too cold, and instead of CaCuSi4 O10 , a porous calcium copper silicate forms; too hot, and calcium silicate (CaSiO3 ) forms. The precursors also strongly impact the course of the reaction, with the most common side product being sodium copper silicate (Na2 CuSi4 O10 ). Optimized conditions for hydrothermal CaCuSi4 O10 formation from calcium chloride, copper(II) nitrate, sodium silicate, and ammonium hydroxide are 350 °C at 3000 psi for 72 h; at longer reaction times, competitive delamination and exfoliation causes crystal fragmentation. These results illustrate that CaCuSi4 O10 is an even more unique material than previously appreciated.

  8. 21 CFR 872.6670 - Silicate protector.

    Science.gov (United States)

    2010-04-01

    ... DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6670 Silicate protector. (a) Identification. A silicate protector is a device made of silicone intended to be applied with an absorbent tipped applicator to...

  9. Evaluation of copper slag blast media for railcar maintenance

    Science.gov (United States)

    Sagers, N. W.; Finlayson, Mack H.

    1989-01-01

    Copper slag was tested as a blasting substitute for zirconium silicate which is used to remove paint from railroad cars. The copper slag tested is less costly, strips paint faster, is produced near the point of need, provides a good bonding surface for paint, and permits the operator to work in a more comfortable position, i.e., standing nearly erect instead of having to crouch. Outdoor blasting with the tested Blackhawk (20 to 40 mesh) copper slag is also environmentally acceptable to the State of Utah. Results of tests for the surface erosion rate with copper slag blasting are included.

  10. Evaluation of copper slag blast media for railcar maintenance

    Science.gov (United States)

    Sagers, N. W.; Finlayson, Mack H.

    1989-06-01

    Copper slag was tested as a blasting substitute for zirconium silicate which is used to remove paint from railroad cars. The copper slag tested is less costly, strips paint faster, is produced near the point of need, provides a good bonding surface for paint, and permits the operator to work in a more comfortable position, i.e., standing nearly erect instead of having to crouch. Outdoor blasting with the tested Blackhawk (20 to 40 mesh) copper slag is also environmentally acceptable to the State of Utah. Results of tests for the surface erosion rate with copper slag blasting are included.

  11. Antibacterial Activity of Silicate Bioceramics

    Institute of Scientific and Technical Information of China (English)

    HU Sheng; NING Congqin; ZHOU Yue; CHEN Lei; LIN Kaili; CHANG Jiang

    2011-01-01

    Four kinds of pure silicate ceramic particles, CaSiO3, Ca3SiO5, bredigite and akermanite were prepared and their bactericidal effects were systematically investigated. The phase compositions of these silicate ceramics were characterized by XRD. The ionic concentration meas urement revealed that the Calcium (Ca) ion concentration were relatively higher in Ca3SiO5 and bredigite, and much lower in CaSiO3 and akermanite. Accordingly, the pH values of the four silicate ceramics extracts showed a positive correlation with the particle concentrations. Meanwhile, by decreasing the particle size, higher Ca ion concentrations can be achieved, leading to the increase of aqueous pH value as well. In summary, all of the four silicate ceramics tested in our study showed antibacterial effect in a dose-dependent manner. Generally, the order of their antibacterial activity against E.coli from strong to weak is Ca3SiO5, bredigite, CaSiO3 and akermanite.

  12. Amended Silicated for Mercury Control

    Energy Technology Data Exchange (ETDEWEB)

    James Butz; Thomas Broderick; Craig Turchi

    2006-12-31

    Amended Silicates{trademark}, a powdered, noncarbon mercury-control sorbent, was tested at Duke Energy's Miami Fort Station, Unit 6 during the first quarter of 2006. Unit 6 is a 175-MW boiler with a cold-side electrostatic precipitator (ESP). The plant burns run-of-the-river eastern bituminous coal with typical ash contents ranging from 8-15% and sulfur contents from 1.6-2.6% on an as-received basis. The performance of the Amended Silicates sorbent was compared with that for powdered activated carbon (PAC). The trial began with a period of baseline monitoring during which no sorbent was injected. Sampling during this and subsequent periods indicated mercury capture by the native fly ash was less than 10%. After the baseline period, Amended Silicates sorbent was injected at several different ratios, followed by a 30-day trial at a fixed injection ratio of 5-6 lb/MMACF. After this period, PAC was injected to provide a comparison. Approximately 40% mercury control was achieved for both the Amended Silicates sorbent and PAC at injection ratios of 5-6 lbs/MMACF. Higher injection ratios did not achieve significantly increased removal. Similar removal efficiencies have been reported for PAC injection trials at other plants with cold-side ESPs, most notably for plants using medium to high sulfur coal. Sorbent injection did not detrimentally impact plant operations and testing confirmed that the use of Amended Silicates sorbent does not degrade fly ash quality (unlike PAC). The cost for mercury control using either PAC or Amended Silicates sorbent was estimated to be equivalent if fly ash sales are not a consideration. However, if the plant did sell fly ash, the effective cost for mercury control could more than double if those sales were no longer possible, due to lost by-product sales and additional cost for waste disposal. Accordingly, the use of Amended Silicates sorbent could reduce the overall cost of mercury control by 50% or more versus PAC for locations where

  13. Effects of ionization on silicate glasses. [Silicate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Primak, W.

    1982-02-01

    This evaluation of radiation effects in silicate glasses caused by ionization is based on our own investigations, on material collected in our files (reports, articles, and notes), and on a computer literature search through recent issues of Physics Abstracts and Chemical Abstracts (and the apparently pertinent references which appeared). Some of our recent results, available heretofore only in internal correspondence, are presented in some detail. It is concluded that research into the behavior of silicate glasses generally will be required before the specific effects in the radioactive waste storage glasses can be properly understood and evaluated. Two particular neglected areas of investigation are targeted for immediate concern: a kinetic analysis of annealing data and the acquisition of data on effects of irradiation at controlled elevated temperatures.

  14. Silicate Composition of the Interstellar Medium

    CERN Document Server

    Fogerty, Shane; Watson, Dan M; Sargent, Benjamin A; Koch, Ingrid

    2016-01-01

    The composition of silicate dust in the diffuse interstellar medium and in protoplanetary disks around young stars informs our understanding of the processing and evolution of the dust grains leading up to planet formation. Analysis of the well-known 9.7{\\mu}m feature indicates that small amorphous silicate grains represent a significant fraction of interstellar dust and are also major components of protoplanetary disks. However, this feature is typically modelled assuming amorphous silicate dust of olivine and pyroxene stoichiometries. Here, we analyze interstellar dust with models of silicate dust that include non-stoichiometric amorphous silicate grains. Modelling the optical depth along lines of sight toward the extinguished objects Cyg OB2 No. 12 and {\\zeta} Ophiuchi, we find evidence for interstellar amorphous silicate dust with stoichiometry intermediate between olivine and pyroxene, which we simply refer to as "polivene." Finally, we compare these results to models of silicate emission from the Trapez...

  15. Surface characterization of silicate bioceramics.

    Science.gov (United States)

    Cerruti, Marta

    2012-03-28

    The success of an implanted prosthetic material is determined by the early events occurring at the interface between the material and the body. These events depend on many surface properties, with the main ones including the surface's composition, porosity, roughness, topography, charge, functional groups and exposed area. This review will portray how our understanding of the surface reactivity of silicate bioceramics has emerged and evolved in the past four decades, owing to the adoption of many complementary surface characterization tools. The review is organized in sections dedicated to a specific surface property, each describing how the property influences the body's response to the material, and the tools that have been adopted to analyse it. The final section introduces the techniques that have yet to be applied extensively to silicate bioceramics, and the information that they could provide.

  16. Hydrothermal Synthesis of Metal Silicates

    Institute of Scientific and Technical Information of China (English)

    Lii Kwang-Hwa

    2004-01-01

    Organically templated metal phosphates have been extensively studied because of interesting structural chemistry and potential applications in catalysis. However, in most cases the organic templates cannot be removed without collapse of the frameworks. This is in contrast to the high thermal stability and extensive applications of zeolites in refinery and petrochemical processes.Therefore, studies have been directed to the synthesis of transition metal silicates to produce more stable frameworks. Our synthetic methods are twofold, namely mild hydrothermal reactions in Teflon-lined autoclaves at 100-200 ℃ using organic amines as templates and high-temperature,high-pressure hydrothermal reactions in gold ampoules contained in a high-pressure reaction vessel at ca. 550 ℃ and 150 Mpa using alkali metal cations as templates. In this presentation I will report the high-temperature, high-pressure hydrothermal synthesis, crystal structures, and solid-state NMR spectroscopy of a number of new silicates of indium, uranium, and transition metals.

  17. Biogenic silicate accumulation in sediments, Jiaozhou Bay

    Institute of Scientific and Technical Information of China (English)

    LI Xuegang; SONG Jinming; DAI Jicui; YUAN Huamao; LI Ning; LI Fengye; SUN Song

    2006-01-01

    It has been widely recognized that low silicate content in seawater is a major limiting factor to phytoplankton primary production in Jiaozhou Bay. However the reason of Si-limitation remains poorly understood. In the present study we measured the biogenic silicate content and discussed the accumulation of silicate in Jiaozhou Bay sediment. The results show that the biogenic silica content in the sediment of the Jiaozhou Bay is obviously much higher than those in the Yellow Sea and the Bohai Sea. The BSi:TN ratios and BSi:16P ratios in the sediment are > 1 and the OC:BSi ratio in sediment is lower than these of Redfield ratio (106:16), indicating that the decomposition rate of OC is much higher than that for BSi in similar conditions. Therefore, the majority of the biogenic silicate was buried and thus did not participate in silicate recycling. Silicate accumulation in sediment may explain why Si limits the phytoplankton growth in the Jiaozhou Bay. Comparing the flux of biogenic silicate from sediments with primary production rate, it can be concluded that only 15.5% of biogenic silicate is hydrolyzed during the journey from surface to bottom in seawater, thus approximate 84.5% of biogenic silicate could reach the bottom. The silicate releasing rate from the sediment to seawater is considerably lower than that of sedimentation of biogenic silicate, indicating silicate accumulation in sediment too. In a word, the silicate accumulation in sediment is the key reason of silicate limiting to phytoplankton growth in Jiaozhou Bay.

  18. Longevity of silicate ceramic restorations.

    Science.gov (United States)

    Beier, Ulrike Stephanie; Dumfahrt, Herbert

    2014-09-01

    The demand for esthetic restorations has resulted in an increased use of dental ceramics as a biocompatible and functionally sufficient alternative to conventional restorative materials. Silicate ceramic restorations are widely used for veneers, inlays, onlays, and crowns in dentistry. Long-term data are of crucial importance to optimize clinical practice. The purpose of the present article is to summarize data of the Innsbruck ceramic evaluation up to 261 months with the focus on longevity and failure characteristics.

  19. Cumulate Fragments in Silicic Ignimbrites

    Science.gov (United States)

    Bachmann, O.; Ellis, B. S.; Wolff, J.

    2014-12-01

    Increasingly, studies are concluding that silicic ignimbrites are the result of the amalgamation of multiple discrete magma batches. Yet the existence of discrete batches presents a conundrum for magma generation and storage; if silicic magma batches are not generated nearly in situ in the upper crust, they must traverse, and reside within, a thermally hostile environment with large temperature gradients, resulting in low survivability in their shallow magmatic hearths. The Snake River Plain (Idaho, USA) is a type example of this 'multi-batch' assembly with ignimbrites containing multiple populations of pyroxene crystals, glass shards, and crystal aggregates. The ubiquitous crystal aggregates hint at a mechanism to facilitate the existence of multiple, relatively small batches of rhyolite in the upper crust. These aggregates contain the same plagioclase, pyroxene, and oxide mineral compositions as single phenocrysts of the same minerals in their host rocks, but they have significantly less silicic bulk compositions and lack quartz and sanidine, which occur as single phenocrysts in the deposits. This implies significant crystallization followed by melt extraction from mushy reservoir margins. The extracted melt then continues to evolve (crystallizing sanidine and quartz) while the melt-depleted margins provide an increasingly rigid and refractory network segregating the crystal-poor batches of magma. The hot, refractory, margins insulate the crystal-poor lenses, allowing (1) extended residence in the upper crust, and (2) preservation of chemical heterogeneities among batches. In contrast, systems that produce cumulates richer in low-temperature phases (quartz, K-feldspars, and/or biotite) favour remelting upon recharge, leading to less segregation of eruptible melt pockets and the formation of gradationally zoned ignimbrites. The occurrence of similar crystal aggregates from a variety of magmatic lineages suggests the generality of this process.

  20. Nanoscale zinc silicate from phytoliths

    Science.gov (United States)

    Qadri, S. B.; Gorzkowski, E. P.; Rath, B. B.; Feng, C. R.; Amarasinghe, R.; Freitas, J. A.; Culbertson, J. C.; Wollmershauser, J. A.

    2017-10-01

    We report a faster, less expensive method of producing zinc silicate nanoparticles. Such particles are used in high volume to make phosphors and anti-corrosion coatings. The approach makes use of phytoliths (plant rocks), which are microscopic, amorphous, and largely silicate particles embedded in plants, that lend themselves to being easily broken down into nanoparticles. Nanoparticles of Zn2SiO4 were produced in a two stage process. In the refinement stage, plant residue, mixed with an appropriate amount of ZnO, was heated in an argon atmosphere to a temperature exceeding 1400 °C for four to six hours and then heated in air at 650 °C to remove excess carbon. TEM shows 50-100 nm nanoparticles. Raman scattering indicates that only the -Zn2SiO4 crystalline phase was present. X-ray analysis indicated pure rhombohedral R 3 bar phase results from using rice/wheat husks. Both samples luminesced predominantly at 523 nm when illuminated with X-rays or UV laser light.

  1. Silicate condensation in Mira variables

    CERN Document Server

    Gail, Hans-Peter; Pucci, Annemarie

    2016-01-01

    We study whether the condensation of silicate dust in Mira envelopes could be caused by cluster formation by the abundant SiO molecules. For a simplified model of the pulsational motions of matter in the the outer layers of a Mira variable which is guided by a numerical model for Mira pulsations, the equations of dust nucleation and growth are solved in the co-moving frame of a fixed mass element. It is assumed that seed particles form by clustering of SiO molecules. The calculation of the nucleation rate is based on the experimental data of Nuth and Donn (1982). The quantity of dust formed is calculated by a moment method and the calculation of radiation pressure on the dusty gas is based on a dirty silicate model. Dust nucleation occurs in the model at the upper culmination of the trajectory of a gas parcel where it stays for a considerable time at low temperatures while subsequent dust growth occurs during the descending part of the motion and continues after the next shock reversed motion. It is found tha...

  2. Oxidation Potentials in Matte Smelting of Copper and Nickel

    Science.gov (United States)

    Matousek, Jan W.

    2014-09-01

    The oxidation potential, given as the base-ten logarithm of the oxygen partial pressure in bars and the temperature [log pO2/ T, °C], defines the state of oxidation of pyrometallurgical extraction and refining processes. This property varies from copper making, [-6/1150]; to lead/zinc smelting, [-10/1200]; to iron smelting, [-13/1600]. The current article extends the analysis to the smelting of copper and nickel/copper sulfide concentrates to produce mattes of the type Cu(Ni)FeS(O) and iron silicate slags, FeOxSiO2—with oxidation potentials of [-7.5/1250].

  3. Santaclaraite, a new calcium-manganese silicate hydrate from California.

    Science.gov (United States)

    Erd, Richard C.; Ohashi, Y.

    1984-01-01

    Santaclaraite, ideally CaMn4(Si5O14(OH))(OH).H2O, occurs as pink and tan veins and masses in Franciscan chert in the Diablo Range, Santa Clara and Stanislaus counties, California. It is associated with four unidentified Mn silicates, Mn-howieite, quartz, braunite, calcite, rhodochrosite, kutnahorite, baryte, harmotome, chalcopyrite and native copper. Santaclaraite is triclinic, space group B1, a 15.633(1), b 7.603(1) , c 12.003(1) A, alpha 109.71(1)o, beta 88.61(1)o, gamma 99.95(1) o, V 1322.0(3) A3; Z = 4. The strongest lines of the X-ray pattern are 7.04(100), 3.003(84), 3.152(80), 7.69(63), 3.847(57) A. Crystals are lamellar to prismatic (flattened on (100)), with good cleavage on (100) and (010); H. 61/2 Dcalc. 3.398 g/cm3, Dmeas. 3.31 (+ or -0.01); optically biaxial negative, alpha 1.681, beta 1.696, gamma 1.708 (all + or - 0.002), 2Valpha 83 (+ or -1)o. Although chemically a hydrated rhodonite, santaclaraite dehydrates to Mn-bustamite at approx 550oC (in air) . Santaclaraite is a five-tetrahedral-repeat single-chain silicate and has structural affinities with rhodonite, nambulite, marsturite, babingtonite and inesite.-J.A.Z.

  4. Silicates materials of high vacuum technology

    CERN Document Server

    Espe, Werner

    2013-01-01

    Materials of High Vacuum Technology, Volume 2: Silicates covers silicate insulators of special importance to vacuum technology. The book discusses the manufacture, composition, and physical and chemical properties of technical glasses, quartz glass, quartzware, vycor glass, ceramic materials, mica, and asbestos.

  5. Mesoporous Silicate Materials in Sensing

    Directory of Open Access Journals (Sweden)

    Paul T. Charles

    2008-08-01

    Full Text Available Mesoporous silicas, especially those exhibiting ordered pore systems and uniform pore diameters, have shown great potential for sensing applications in recent years. Morphological control grants them versatility in the method of deployment whether as bulk powders, monoliths, thin films, or embedded in coatings. High surface areas and pore sizes greater than 2 nm make them effective as adsorbent coatings for humidity sensors. The pore networks also provide the potential for immobilization of enzymes within the materials. Functionalization of materials by silane grafting or through cocondensation of silicate precursors can be used to provide mesoporous materials with a variety of fluorescent probes as well as surface properties that aid in selective detection of specific analytes. This review will illustrate how mesoporous silicas have been applied to sensing changes in relative humidity, changes in pH, metal cations, toxic industrial compounds, volatile organic compounds, small molecules and ions, nitroenergetic compounds, and biologically relevant molecules.

  6. Nanotubes within transition metal silicate hollow spheres: Facile preparation and superior lithium storage performances

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Fan; An, Yongling; Zhai, Wei; Gao, Xueping [Key Laboratory for Liquid–Solid Structural Evolution & Processing of Materials (Ministry of Education), Jinan 250100 (China); Feng, Jinkui, E-mail: jinkui@sdu.edu.cn [Key Laboratory for Liquid–Solid Structural Evolution & Processing of Materials (Ministry of Education), Jinan 250100 (China); Ci, Lijie [Key Laboratory for Liquid–Solid Structural Evolution & Processing of Materials (Ministry of Education), Jinan 250100 (China); Xiong, Shenglin [School of Materials Science and Engineering, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)

    2015-10-15

    Highlights: • The hollow Co{sub 2}SiO{sub 4}, MnSiO{sub 3} and CuSiO{sub 3} were successfully prepared by a facile hydrothermal method using SiO{sub 2} nanosphere. • The hollow Co{sub 2}SiO{sub 4}, MnSiO{sub 3} and CuSiO{sub 3} were tested as anode materials for lithium batteries. • The hollow Co{sub 2}SiO{sub 4}, MnSiO{sub 3} and CuSiO{sub 3} delivered superior electrochemical performance. • The lithium storage mechanism is probe via cyclic voltammetry and XPS. - Abstract: A series of transition metal silicate hollow spheres, including cobalt silicate (Co{sub 2}SiO{sub 4}), manganese silicate (MnSiO{sub 3}) and copper silicate (CuSiO{sub 3}.2H{sub 2}O, CuSiO{sub 3} as abbreviation in the text) were prepared via a simple and economic hydrothermal method by using silica spheres as chemical template. Time-dependent experiments confirmed that the resultants formed a novel type of hierarchical structure, hollow spheres assembled by numerous one-dimensional (1D) nanotubes building blocks. For the first time, the transition metal silicate hollow spheres were characterized as novel anode materials of Li-ion battery, which presented superior lithium storage capacities, cycle performance and rate performance. The 1D nanotubes assembly and hollow interior endow this kind of material facilitate fast lithium ion and electron transport and accommodate the big volume change during the conversion reactions. Our study shows that low-cost transition metal silicate with rationally designed nanostructures can be promising anode materials for high capacity lithium-ion battery.

  7. Carbon Monoxide Silicate Reduction System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Carbon Monoxide Silicate Reduction System (COSRS) is a novel technology for producing large quantities of oxygen on the Moon. Oxygen yields of 15 kilograms per...

  8. Carbon Monoxide Silicate Reduction System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Carbon Monoxide Silicate Reduction System (COSRS) is an innovative method that for the first time uses the strong reductant carbon monoxide to both reduce iron...

  9. Characterization of silicate/Si(001) interfaces

    Science.gov (United States)

    Copel, M.; Cartier, E.; Narayanan, V.; Reuter, M. C.; Guha, S.; Bojarczuk, N.

    2002-11-01

    Many of the proposed high permittivity gate dielectrics for silicon-based microelectronics rely on a stack configuration, with an SiO2 buffer layer to provide an interface. We describe a means for creating gate dielectrics with a direct yttrium silicate-silicon interface through the solid-state reaction of yttria and silicon oxynitride, avoiding the preparation of an oxide-free silicon surface. Characterization by medium-energy ion scattering indicates complete consumption of the underlying oxide through silicate formation during high-temperature annealing. Furthermore, the silicate dielectric exhibits small flat-band voltage shifts, indicating low quantities of charge, without passivation steps. Creation of a silicate-silicon interfaces by a simple route may enable the study of an alternate class of dielectrics.

  10. Intrinsic luminescence of alkali silicate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Arbuzov, V.I.; Grabovskis, V.Y.; Tolstoi, M.N.; Vitol, I.K.

    1986-09-01

    This study obtains additional information on L centers and their role in electron excitation and intrinsic luminescence of a whole series. (Li, Na, K, Rb, and Cs) of alkali silicate glasses. The authors compare the features of the interaction with radiation of specimens of glass and crystal of a similar chemical composition, since silicates of alkali metals can be obtained in both the glassy and crystalline states.

  11. Thermodynamics and Kinetics of Silicate Vaporization

    Science.gov (United States)

    Jacobson, Nathan S.; Costa, Gustavo C. C.

    2015-01-01

    Silicates are a common class of materials that are often exposed to high temperatures. The behavior of these materials needs to be understood for applications as high temperature coatings in material science as well as the constituents of lava for geological considerations. The vaporization behavior of these materials is an important aspect of their high temperature behavior and it also provides fundamental thermodynamic data. The application of Knudsen effusion mass spectrometry (KEMS) to silicates is discussed. There are several special considerations for silicates. The first is selection of an appropriate cell material, which is either nearly inert or has well-understood interactions with the silicate. The second consideration is proper measurement of the low vapor pressures. This can be circumvented by using a reducing agent to boost the vapor pressure without changing the solid composition or by working at very high temperatures. The third consideration deals with kinetic barriers to vaporization. The measurement of these barriers, as encompassed in a vaporization coefficient, is discussed. Current measured data of rare earth silicates for high temperature coating applications are discussed. In addition, data on magnesium-iron-silicates (olivine) are presented and discussed.

  12. Control of domoic acid toxin expression in Pseudo-nitzschia multiseries by copper and silica: relevance to mussel aquaculture in New England (USA).

    Science.gov (United States)

    Fuentes, M Soledad; Wikfors, Gary H

    2013-02-01

    The production of the toxin Domoic Acid (DA) by the diatoms Pseudo-nitzschia spp. is affected by several environmental factors, among them copper and silica. The effects of these nutrients upon DA production have been studied individually, but not in combination. There is evidence, however, that in diatoms copper can enter the cell via the silicic-acid transport site. The goal of this study was to analyze the effect of the interaction between copper and silicic-acid supply upon DA production in Pseudo-nitzschia multiseries. The study was motivated by concerns about the risk of toxigenic Pseudo-nitzschia spp. impacting mussel aquaculture in New England (USA). The results of the present study do not indicate that copper uses the silicic acid transport site to enter the cell; nevertheless, there is an interaction between these two nutrients that produces a synergistic affect upon toxin production. A small increase in copper, without a simultaneous increase in silicate, as well as an increase in both copper and silicate, leads to DA up-regulation. Furthermore, the field component of this study reports the presence of species of Pseudo-nitzschia on the New England coast that are capable of producing DA. Together these findings indicate that risk of DA impacting mussel aquaculture along the coast of New England would be increased by an unusual enrichment of copper in the vicinity of mussel farms.

  13. Float processing of high-temperature complex silicate glasses and float baths used for same

    Science.gov (United States)

    Cooper, Reid Franklin (Inventor); Cook, Glen Bennett (Inventor)

    2000-01-01

    A float glass process for production of high melting temperature glasses utilizes a binary metal alloy bath having the combined properties of a low melting point, low reactivity with oxygen, low vapor pressure, and minimal reactivity with the silicate glasses being formed. The metal alloy of the float medium is exothermic with a solvent metal that does not readily form an oxide. The vapor pressure of both components in the alloy is low enough to prevent deleterious vapor deposition, and there is minimal chemical and interdiffusive interaction of either component with silicate glasses under the float processing conditions. Alloys having the desired combination of properties include compositions in which gold, silver or copper is the solvent metal and silicon, germanium or tin is the solute, preferably in eutectic or near-eutectic compositions.

  14. Influence of silicate anions structure on desilication in silicate-bearing sodium aluminate solution

    Institute of Scientific and Technical Information of China (English)

    刘桂华; 张闻; 齐天贵; 彭志宏; 周秋生; 李小斌

    2016-01-01

    The structural changes of silicate anions in the desilication process with the addition of calcium hydrate alumino-carbonate were studied by measuring Raman spectra, infrared spectra and corresponding second derivative spectra. The results show that the desilication ratio in the solution prepared by the addition of sodium silicate (solution-SS) is much greater than that in the solution by the addition of green liquor (solution-GL), and low alumina concentration in the sodium aluminate solutions facilitates the desilication process. It is also shown that alumino-silicate anions in the solution-GL, and Q3 polymeric silicate anions in solution-SS are predominant, respectively. In addition, increasing the concentration of silica favors respectively the formation of the alumino-silicate or the Q3 silicate anions in the solution-GL or the solution-SS. Therefore, it can be inferred that the low desilication ratio in the silicate-bearing aluminate solution is mainly attributed to the existence of alumino-silicate anions.

  15. OPTIMAL METHOD FOR PREPARATION OF SILICATE ROCK SAMPLES FOR ANALYTICAL PURPOSES

    Directory of Open Access Journals (Sweden)

    Maja Vrkljan

    2004-12-01

    Full Text Available The purpose of this study was to determine an optimal dissolution method for silicate rock samples for further analytical purposes. Analytical FAAS method of determining cobalt, chromium, copper, nickel, lead and zinc content in gabbro sample and geochemical standard AGV-1 has been applied for verification. Dissolution in mixtures of various inorganic acids has been tested, as well as Na2CO3 fusion technique. The results obtained by different methods have been compared and dissolution in the mixture of HNO3 + HF has been recommended as optimal.

  16. Characterization and nutrient release from silicate rocks and influence on chemical changes in soil

    Directory of Open Access Journals (Sweden)

    Douglas Ramos Guelfi Silva

    2012-06-01

    Full Text Available The expansion of Brazilian agriculture has led to a heavy dependence on imported fertilizers to ensure the supply of the growing food demand. This fact has contributed to a growing interest in alternative nutrient sources, such as ground silicate rocks. It is necessary, however, to know the potential of nutrient release and changes these materials can cause in soils. The purpose of this study was to characterize six silicate rocks and evaluate their effects on the chemical properties of treated soil, assessed by chemical extractants after greenhouse incubation. The experimental design consisted of completely randomized plots, in a 3 x 6 factorial scheme, with four replications. The factors were potassium levels (0-control: without silicate rock application; 200; 400; 600 kg ha-1 of K2O, supplied as six silicate rock types (breccia, biotite schist, ultramafic rock, phlogopite schist and two types of mining waste. The chemical, physical and mineralogical properties of the alternative rock fertilizers were characterized. Treatments were applied to a dystrophic Red-Yellow Oxisol (Ferralsol, which was incubated for 100 days, at 70 % (w/w moisture in 3.7 kg/pots. The soil was evaluated for pH; calcium and magnesium were extracted with KCl 1 mol L-1; potassium, phosphorus and sodium by Mehlich 1; nickel, copper and zinc with DTPA; and the saturation of the cation exchange capacity was calculated for aluminum, calcium, magnesium, potassium, and sodium, and overall base saturation. The alternative fertilizers affected soil chemical properties. Ultramafic rock and Chapada mining byproduct (CMB were the silicate rocks that most influenced soil pH, while the mining byproduct (MB led to high K levels. Zinc availability was highest in the treatments with mining byproduct and Cu in soil fertilized with Chapada and mining byproduct.

  17. Copper Planar Microcoils Applied to Magnetic Actuation

    CERN Document Server

    Moulin, J; Martincic, E; Dufour-Gergam, E

    2008-01-01

    Recent advances in microtechnology allow realization of planar microcoils. These components are integrated in MEMS as magnetic sensor or actuator. In the latter case, it is necessary to maximize the effective magnetic field which is proportional to the current passing through the copper track and depends on the distance to the generation microcoil. The aim of this work was to determine the optimal microcoil design configuration for magnetic field generation. The results were applied to magnetic actuation, taking into account technological constraints. In particular, we have considered different realistic configurations that involve a magnetically actuated device coupled to a microcoil. Calculations by a semi-analytical method using Matlab software were validated by experimental measurements. The copper planar microcoils are fabricated by U.V. micromoulding on different substrates: flexible polymer (Kapton) and silicate on silicon. They are constituted by a spiral-like continuous track. Their total surface is ...

  18. Core formation in silicate bodies

    Science.gov (United States)

    Nimmo, F.; O'Brien, D. P.; Kleine, T.

    2008-12-01

    Differentiation of a body into a metallic core and silicate mantle occurs most efficiently if temperatures are high enough to allow at least the metal to melt [1], and is enhanced if matrix deformation occurs [2]. Elevated temperatures may occur due to either decay of short-lived radio-isotopes, or gravitational energy release during accretion [3]. For bodies smaller than the Moon, core formation happens primarily due to radioactive decay. The Hf-W isotopic system may be used to date core formation; cores in some iron meteorites and the eucrite parent body (probably Vesta) formed within 1 My and 1-4~My of solar system formation, respectively [4]. These formation times are early enough to ensure widespread melting and differentiation by 26Al decay. Incorporation of Fe60 into the core, together with rapid early mantle solidification and cooling, may have driven early dynamo activity on some bodies [5]. Iron meteorites are typically depleted in sulphur relative to chondrites, for unknown reasons [6]. This depletion contrasts with the apparently higher sulphur contents of cores in larger planetary bodies, such as Mars [7], and also has a significant effect on the timing of core solidification. For bodies of Moon-size and larger, gravitational energy released during accretion is probably the primary cause of core formation [3]. The final stages of accretion involve large, stochastic collisions [8] between objects which are already differentiated. During each collision, the metallic cores of the colliding objects merge on timescales of a few hours [9]. Each collision will reset the Hf-W isotopic signature of both mantle and core, depending on the degree to which the impactor core re-equilibrates with the mantle of the target [10]. The re-equilibration efficiency depends mainly on the degree to which the impactor emulsifies [11], which is very uncertain. Results from N-body simulations [8,12] suggest that significant degrees of re- equilibration are required [4,10]. Re

  19. Nanostructure of Calcium Silicate Hydrates in Cements

    KAUST Repository

    Skinner, L. B.

    2010-05-11

    Calcium silicate hydrate (CSH) is the major volume phase in the matrix of Portland cement concrete. Total x-ray scattering measurements with synchrotron x rays on synthetic CSH(I) shows nanocrystalline ordering with a particle diameter of 3.5(5) nm, similar to a size-broadened 1.1 nm tobermorite crystal structure. The CSH component in hydrated tricalcium silicate is found to be similar to CSH(I). Only a slight bend and additional disorder within the CaO sheets is required to explain its nanocrystalline structure. © 2010 The American Physical Society.

  20. Copper allergy from dental copper amalgam?

    Science.gov (United States)

    Gerhardsson, Lars; Björkner, Bert; Karlsteen, Magnus; Schütz, Andrejs

    2002-05-06

    A 65-year-old female was investigated due to a gradually increasing greenish colour change of her plastic dental splint, which she used to prevent teeth grinding when sleeping. Furthermore, she had noted a greenish/bluish colour change on the back of her black gloves, which she used to wipe her tears away while walking outdoors. The investigation revealed that the patient had a contact allergy to copper, which is very rare. She had, however, had no occupational exposure to copper. The contact allergy may be caused by long-term exposure of the oral mucosa to copper from copper-rich amalgam fillings, which were frequently used in childhood dentistry up to the 1960s in Sweden. The deposition of a copper-containing coating on the dental splint may be caused by a raised copper intake from drinking water, increasing the copper excretion in saliva, in combination with release of copper due to electrochemical corrosion of dental amalgam. The greenish colour change of the surface of the splint is probably caused by deposition of a mixture of copper compounds, e.g. copper carbonates. Analysis by the X-ray diffraction technique indicates that the dominant component is copper oxide (Cu2O and CuO). The corresponding greenish/bluish discoloration observed on the back of the patient's gloves may be caused by increased copper excretion in tears.

  1. Copper Products Capacity Expansion Stimulate the Copper Consumption

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    <正>The dramatic growth of copper consumption in China can directly be seen from the expansion of copper products capacity.According to sta- tistics,in the past 4 years,the improvement on the balance of trade on copper bar,copper,and copper alloy and copper wire & cable has driven the growth of copper consumption a lot.

  2. Antwerp Copper Plates

    DEFF Research Database (Denmark)

    Wadum, Jørgen

    1999-01-01

    In addition to presenting a short history of copper paintings, topics detail artists’ materials and techniques, as well as aspects of the copper industry, including mining, preparation and trade routes.......In addition to presenting a short history of copper paintings, topics detail artists’ materials and techniques, as well as aspects of the copper industry, including mining, preparation and trade routes....

  3. 21 CFR 172.410 - Calcium silicate.

    Science.gov (United States)

    2010-04-01

    ... CONSUMPTION (CONTINUED) FOOD ADDITIVES PERMITTED FOR DIRECT ADDITION TO FOOD FOR HUMAN CONSUMPTION Anticaking... agent in food in an amount not in excess of that reasonably required to produce its intended effect. (b... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium silicate. 172.410 Section 172.410 Food...

  4. Stability of calcium silicate in basic solution

    Institute of Scientific and Technical Information of China (English)

    刘桂华; 李小斌; 彭志宏; 周秋生

    2003-01-01

    Mixture of CaO and SiO2 was sintered at 1 200 or 1 400 ℃ according to the mole ratio of CaO/SiO2 of 1 or 2, and then calcium silicate was leached in pure caustic or soda solution. The results indicated that calcium silicate exists much more stably in caustic solution than that in soda solution, and CaO*SiO2 is more stable than β-2CaO*SiO2 whether in caustic solution or in soda solution. The increase of sintering temperature favored the stability of calcium silicate in the leaching process. When β-2CaO*SiO2 was leached in soda solution, the increase of leaching temperature and time resulted in decomposing of more calcium silicate. And when β-2CaO*SiO2 was leached in caustic solution at high temperature, much 2CaO*SiO2*H2O but little CaO*SiO2*H2O appeared in slag.

  5. COMPARISON OF SOL-GEL SILICATE COATINGS ON Ti SUBSTRATE

    OpenAIRE

    2012-01-01

    The objective of the submitted work was to prepare and to characterize two types of silicate coatings prepared by the sol-gel method using the dip-coating technique on a titanium substrate. Efforts have been made to use mechanical properties of bio-inert titanium and bioactive properties of a silicate layer enriched with an admixture of compounds identified below. The first group consisted of silicate coatings containing silver, brushite and monetite. The other group of silicate coatings cont...

  6. Copper and copper proteins in Parkinson's disease.

    Science.gov (United States)

    Montes, Sergio; Rivera-Mancia, Susana; Diaz-Ruiz, Araceli; Tristan-Lopez, Luis; Rios, Camilo

    2014-01-01

    Copper is a transition metal that has been linked to pathological and beneficial effects in neurodegenerative diseases. In Parkinson's disease, free copper is related to increased oxidative stress, alpha-synuclein oligomerization, and Lewy body formation. Decreased copper along with increased iron has been found in substantia nigra and caudate nucleus of Parkinson's disease patients. Copper influences iron content in the brain through ferroxidase ceruloplasmin activity; therefore decreased protein-bound copper in brain may enhance iron accumulation and the associated oxidative stress. The function of other copper-binding proteins such as Cu/Zn-SOD and metallothioneins is also beneficial to prevent neurodegeneration. Copper may regulate neurotransmission since it is released after neuronal stimulus and the metal is able to modulate the function of NMDA and GABA A receptors. Some of the proteins involved in copper transport are the transporters CTR1, ATP7A, and ATP7B and the chaperone ATOX1. There is limited information about the role of those biomolecules in the pathophysiology of Parkinson's disease; for instance, it is known that CTR1 is decreased in substantia nigra pars compacta in Parkinson's disease and that a mutation in ATP7B could be associated with Parkinson's disease. Regarding copper-related therapies, copper supplementation can represent a plausible alternative, while copper chelation may even aggravate the pathology.

  7. The fatty acids and alkanes of Satureja adamovicii Silic and Satureja fukarekii Silic (NOTE

    Directory of Open Access Journals (Sweden)

    DUSANKA KITIC

    1999-05-01

    Full Text Available The content and composition of fatty acids and alkanes of Satureja adamovicii Silic and Satureja fukarekii Silic were analized by GC. It was found that unsaturated acids prevailed and that the major components were palmitic, oleic, linoleic and linolenic acids. The hydrocarbon fractions of pentane extracts were shown to consist of the alkane homologues (C17 to C34 with nonacosane and hentriacontane being prevailing compounds.

  8. 40 CFR 721.9513 - Modified magnesium silicate polymer (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Modified magnesium silicate polymer... Specific Chemical Substances § 721.9513 Modified magnesium silicate polymer (generic). (a) Chemical... as modified magnesium silicate polymer (PMN P-98-604) is subject to reporting under this section for...

  9. Factors affecting lead release in sodium silicate-treated partial lead service line replacements.

    Science.gov (United States)

    Zhou, Emily; Payne, Sarah Jane O; Hofmann, Ron; Andrews, Robert C

    2015-01-01

    Water quality parameters affecting sodium silicate performance in partial lead service line replacements were examined using a fractional factorial experimental design and static pipe systems. An external copper wire was used to create a galvanic connection between a former lead service line and a new copper pipe. The pipe systems were filled with lab prepared water made to mimic real water quality. Water was changed on a three times per week basis. A 2(4-1) fractional factorial design was used to evaluate the impact of alkalinity (15 mg L(-1) or 250 mg L(-1) as CaCO3), nitrate (1 mg L(-1) or 7 mg L(-1) as N), natural organic matter (1 mg L(-1) or 7 mg L(-1) as dissolved organic carbon), and disinfectant type (1 mg L(-1) chlorine or 3 mg L(-1) monochloramine), resulting in eight treatment conditions. Fractional factorial analysis revealed that alkalinity, natural organic matter and monochloramine had a significant positive effect on galvanic current. Natural organic matter and monochloramine also had a significant positive effect with respect to both total and dissolved lead release. For the treatment conditions examined, 67-98% of the lead released through galvanic currents was stored as corrosion scales and predominantly comprised of particulate lead (96.1-99.9%) for all eight treatments. The use of monochloramine and the presence of natural organic matter (7 mg L(-1)) were not favourable for corrosion control in sodium silicate-treated partial lead service line replacements, although further studies would be required to characterize optimal water quality parameters for specific water quality types. For utilities operating with sodium silicate as a corrosion inhibitor, this work offers further evidence regarding the consideration of chlorine as a secondary disinfectant instead of monochloramine, as well as the value of controlling natural organic matter in distributed water.

  10. Characterizing Amorphous Silicates in Extraterrestrial Materials

    Science.gov (United States)

    Fu, X.; Wang, A.; Krawczynski, M. J.

    2015-12-01

    Amorphous silicates are common in extraterrestrial materials. They are seen in the matrix of carbonaceous chondrites as well as in planetary materials. Tagish Lake is one of the most primitive carbonaceous meteorites in which TEM and XRD analyses found evidence for poorly crystalline phyllosilicate-like species; Raman spectra revealed amorphous silicates with variable degree of polymerization and low crystallinity. On Mars, CheMin discovered amorphous phases in all analyzed samples, and poorly crystalline smectite in mudstone samples. These discoveries pose questions on the crystallinity of phyllosilicates found by remote sensing on Mars, which is directly relevant to aqueous alteration during geologic history of Mars. Our goal is to use spectroscopy to better characterize amorphous silicates. We use three approaches: (1) using silicate glasses synthesized with controlled chemistry to study the effects of silicate polymerization and (2) using phyllosilicates synthesized with controlled hydrothermal treatment to study the effect of crystallinity on vibrational spectroscopy, finally (3) to use the developed correlations in above two steps to study amorphous phases in meteorites, and those found in future missions to Mars. In the 1st step, silicate glasses were synthesized from pure oxides in a range of NBO/T ratios (from 0 to 4). Depending on the targeted NBO/T and composition of mixed oxides, temperatures for each experiment fell in a range from 1260 to 1520 °C, run for ~ 4 hrs. The melt was quenched in liquid N2 or water. Homogeneity of glass was checked under optical microscopy. Raman spectra were taken over 100 spots on small chips free of bubbles and crystals. We have observed that accompanying an increase of NBO/T, there is a strengthening and a position shift of the Raman peak near 1000 cm-1 (Si-Onon-bridging stretching mode), and the weakening of broad Raman peaks near 500 cm-1 (ring breathing mode) and 700cm-1 (Si-Obridging-Si mode). We are building the

  11. Cooling rate calculations for silicate glasses.

    Science.gov (United States)

    Birnie, D. P., III; Dyar, M. D.

    1986-03-01

    Series solution calculations of cooling rates are applied to a variety of samples with different thermal properties, including an analog of an Apollo 15 green glass and a hypothetical silicate melt. Cooling rates for the well-studied green glass and a generalized silicate melt are tabulated for different sample sizes, equilibration temperatures and quench media. Results suggest that cooling rates are heavily dependent on sample size and quench medium and are less dependent on values of physical properties. Thus cooling histories for glasses from planetary surfaces can be estimated on the basis of size distributions alone. In addition, the variation of cooling rate with sample size and quench medium can be used to control quench rate.

  12. Tracking bubble evolution inside a silicic dike

    Science.gov (United States)

    Álvarez-Valero, Antonio M.; Okumura, Satoshi; Arzilli, Fabio; Borrajo, Javier; Recio, Clemente; Ban, Masao; Gonzalo, Juan C.; Benítez, José M.; Douglas, Madison; Sasaki, Osamu; Franco, Piedad; Gómez-Barreiro, Juan; Carnicero, Asunción

    2016-10-01

    Pressure estimates from rapidly erupted crustal xenoliths constrain the depth of intrusion of the silicic lavas hosting them. This represents an opportunity for tracking magmatic bubble's evolution and quantifying the variation in bubble volume during rapid magma ascent through a volcanic dike just prior to eruption. The petrology, stable-isotope geochemistry and X-ray micro-tomography of dacites containing crustal xenoliths, erupted from a Neogene volcano in SE Spain, showed an increase in porosity from ~ 1.7 to 6.4% from ~ 19 to 13 km depth, at nearly constant groundmass and crystal volumes. This result provides additional constraints for experimental and numerical simulations of subvolcanic magma-crust degassing processes in silicic systems, and may allow the characterization of volcanic eruptive styles based on volatile content.

  13. Recycle of silicate waste into mesoporous materials.

    Science.gov (United States)

    Kim, Jung Ho; Kim, Minwoo; Yu, Jong-Sung

    2011-04-15

    Template synthesis of porous carbon materials usually requires selective removal of template silica from the carbon/silica composites. It not only involves waste of valuable chemicals, but also poses significant environmental concerns including high waste treatment cost. Recycling of silicates released from such nanocasting methods is successfully performed for the first time to regenerate valuable mesoporous MCM and SBA type silica materials, which will not only help in saving valuable chemicals, but also in decreasing chemical waste, contributing in improvement of our environmental standards. This approach can thus improve cost effectiveness for the mass production of nanostructured carbon and others utilizing silica directed nanocasting method by recycling otherwise silicate waste into highly desirable valuable mesoporous silica.

  14. Discovery of exhalative rock—ferro-siliceous rock in the Deerni copper deposit of East Kunlun Mountains and its metallogenic significance%东昆仑德尔尼铜矿喷流岩——铁硅质岩的发现及其成矿意义

    Institute of Scientific and Technical Information of China (English)

    宋忠宝; 栗亚芝; 陈向阳; 陈博; 任有祥; 张雨莲; 张晓飞

    2012-01-01

    "carbonaceous sand slate" in Deerni area is a rock name used for more than 30 years, because this kind of rock is irrelevant to mineralization. Through detailed research work,the authors discovered that this kind of rock can be divided into two kinds: one is terrigenous clastic rock, which is a kind of normal sedimentary rock, i.e., carbonaceous sandy slate, having no direct relationship with mineralization, whereas the other is exhalative rock formed by submarine exhalation-ferro-siliceous rock. It is thus inferred that the Deemi large-size Co-Cu deposit was mainly formed by submarine exhalative-sedimentation and was later enriched by superimposi-tion of multi -stage mineralization. This discovery has important theoretical and guiding significance in search for such ore deposits in Deerni area.%德尔尼地区的“炭质(砂)板岩”是一个使用了30多年的岩石名称,前人把这类岩石当作与成矿并无任何关系的一种沉积岩.本次工作发现并证实这类岩石进一步可分为2种:一种为陆源碎屑岩,即正常沉积岩——炭质(砂)板岩,与成矿无直接关系;另一种为海底喷流作用形成的一种喷流岩——铁硅质岩.由此推断德尔尼大型铜(钴)矿床,是一个以海底喷流-沉积成矿为主体的后期有叠加成矿的多期成矿作用形成的矿床.这在德尔尼地区寻找该类矿床有重要的理论意义和指导意义.

  15. Metal and silicate particles including nanoparticles are present in electronic cigarette cartomizer fluid and aerosol.

    Directory of Open Access Journals (Sweden)

    Monique Williams

    Full Text Available Electronic cigarettes (EC deliver aerosol by heating fluid containing nicotine. Cartomizer EC combine the fluid chamber and heating element in a single unit. Because EC do not burn tobacco, they may be safer than conventional cigarettes. Their use is rapidly increasing worldwide with little prior testing of their aerosol.We tested the hypothesis that EC aerosol contains metals derived from various components in EC.Cartomizer contents and aerosols were analyzed using light and electron microscopy, cytotoxicity testing, x-ray microanalysis, particle counting, and inductively coupled plasma optical emission spectrometry.The filament, a nickel-chromium wire, was coupled to a thicker copper wire coated with silver. The silver coating was sometimes missing. Four tin solder joints attached the wires to each other and coupled the copper/silver wire to the air tube and mouthpiece. All cartomizers had evidence of use before packaging (burn spots on the fibers and electrophoretic movement of fluid in the fibers. Fibers in two cartomizers had green deposits that contained copper. Centrifugation of the fibers produced large pellets containing tin. Tin particles and tin whiskers were identified in cartridge fluid and outer fibers. Cartomizer fluid with tin particles was cytotoxic in assays using human pulmonary fibroblasts. The aerosol contained particles >1 µm comprised of tin, silver, iron, nickel, aluminum, and silicate and nanoparticles (<100 nm of tin, chromium and nickel. The concentrations of nine of eleven elements in EC aerosol were higher than or equal to the corresponding concentrations in conventional cigarette smoke. Many of the elements identified in EC aerosol are known to cause respiratory distress and disease.The presence of metal and silicate particles in cartomizer aerosol demonstrates the need for improved quality control in EC design and manufacture and studies on how EC aerosol impacts the health of users and bystanders.

  16. Six White Dwarfs with Circumstellar Silicates

    CERN Document Server

    Jura, M; Zuckerman, B

    2008-01-01

    Spitzer Space Telescope spectra reveal 10 micron silicate emission from circumstellar dust orbiting six externally-polluted white dwarfs. Micron-size glasses with an olivine stoichiometry can account for the distinctively broad wings that extend to 12 microns; these particles likely are produced by tidal-disruption of asteroids. The absence of infrared PAH features is consistent with a scenario where extrasolar rocky planets are assembled from carbon-poor solids.

  17. Adsorption of dimeric surfactants in lamellar silicates

    Energy Technology Data Exchange (ETDEWEB)

    Balcerzak, Mateusz; Pietralik, Zuzanna [Department of Macromolecular Physics, Faculty of Physics, A. Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland); Domka, Ludwik [Department of Metalorganic Chemistry, Faculty of Chemistry, A. Mickiewicz University, Grunwaldzka 6, 60-780 Poznań (Poland); Skrzypczak, Andrzej [Institute of Chemical Technology, Poznań University of Technology, Berdychowo 4, 60-965 Poznań (Poland); Kozak, Maciej, E-mail: mkozak@amu.edu.pl [Department of Macromolecular Physics, Faculty of Physics, A. Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland)

    2015-12-01

    Highlights: • The intercalation of dimeric surfactants changed the morphology of MMT samples. • XRD indicated structures formed by surfactant molecules in interlayer space. • The four-step thermal decomposition of dimeric surfactant, confirms intercalation. - Abstract: The adsorption of different types of cationic surfactants in lamellar silicates changes their surface character from hydrophilic to hydrophobic. This study was undertaken to obtain lamellar silicates modified by a series of novel dimeric (gemini) surfactants of different length alkyl chains and to characterise these organophilised materials. Synthetic sodium montmorillonite SOMASIF® ME 100 (M) and enriched bentonite of natural origin (Nanoclay – hydrophilic bentonite®) were organophilised with dimeric (gemini) surfactants (1,1′-(1,4-butanediyl)bis(alkoxymethyl)imidazolium dichlorides). As a result of surfactant molecule adsorption in interlamellar space, the d-spacing (d{sub 001}) increased from 0.97 nm (for the anhydrous structure) to 2.04 nm. A Fourier transform infrared spectroscopy (FTIR) analysis of the modified systems reveals bands assigned to the stretching vibrations of the CH{sub 2} and CH{sub 3} groups and the scissoring vibrations of the NH group from the structure of the dimeric surfactants. Thermogravimetric (TG) and derivative thermogravimetric (DTG) studies imply a four-stage process of surfactant decomposition. Scanning electron microscopy (SEM) images provide information on the influence of dimeric surfactant intercalation into the silicate structures. Particles of the modified systems show a tendency toward the formation of irregularly shaped agglomerates.

  18. Effect of silicate solutions on metakaolinite based cementitious material

    Institute of Scientific and Technical Information of China (English)

    XIAO Xue-jun; LI Hua-jian; SUN Heng-hu

    2006-01-01

    High performance metakaolinite based cementitious materials were prepared with metakaolinite as main component, and the different modules of Na and Na-K silicate solutions as diagenetic agent. The results show that the mechanical properties are affected by different silicate solutions, compressive strengths of pastes hydrated for 3 d and 28 d with Na-K silicate solution (The modulus is 1) are about 43.68 and 78.52 MPa respectively. By analyzing the mechanical properties of Metakaolinite based cementitious materials, the diagenetic effect of lower module is better than higher module, and Na-K silicate solution is better than Na silicate solution. The structure of the Na and Na-K silicate solutions is studied with IR and 29Si NMR, the reason of the lower module and Na-K silicate solution improving the mechanical properties is that the low module silicate solution has lower polymeric degree of silicon dioxide, and the higher polymeric degree of silicon oxide tetrahedron(Q4) in Na-K silicate solution is less than Na silicate solution.

  19. Diseases associated with exposure to silica and nonfibrous silicate minerals. Silicosis and Silicate Disease Committee

    Energy Technology Data Exchange (ETDEWEB)

    1988-07-01

    Silicosis, a disease of historical importance, continues to occur cryptically today. Its pathogenesis is under ongoing study as new concepts of pathobiology evolve. In this article, the gross and microscopic features of the disease in the lungs and the lesions in lymph nodes and other viscera are described. These tissue changes are then discussed in the context of clinical disease and other possible or established complications of silica exposure (ie, scleroderma and rheumatoid arthritis, glomerulonephritis, and bronchogenic carcinoma). Silicates are members of a large family of common minerals, some of which have commercial importance. Silicates are less fibrogenic than silica when inhaled into the lungs, but cause characteristic lesions after heavy prolonged exposure. The features of these disease conditions are described herein. Various aspects of the mineralogy and tissue diagnosis of silicosis and lung disease due to silicates are reviewed. An overview of contemporary regulatory considerations is provided.204 references.

  20. Effect of Na2CO3 Addition on Carbothermic Reduction of Copper Smelting Slag to Prepare Crude Fe-Cu Alloy

    Science.gov (United States)

    Guo, Zhengqi; Zhu, Deqing; Pan, Jian; Yao, Weijie; Xu, Wuqi; Chen, Jinan

    2017-09-01

    Copper smelting slag is a useful secondary resource containing high iron and copper, which can be utilized to prepare crude Fe-Cu alloy by a direct reduction-magnetic separation process for making weathering-resistant steel. However, it is difficult to recover iron and copper from the slag by direct reduction since the iron mainly occurs in fayalite and the copper is held in copper sulfide. Therefore, enhancement reduction of copper slag is conducted to improve the recovery of copper and iron. Additives such as Na2CO3 has been proven to be capable of reinforcing the reduction of refractory iron ore. In this research, the effect of Na2CO3 on the carbothermic reduction of copper slag was investigated, and phase transformations during reduction and the distributing characteristics of iron and copper in the alloy and non-metallic phases of the reduced pellets were also studied. The results show that the metallization rate of iron and copper was increased with the addition of Na2CO3, leading to higher iron and copper recovery in Fe-Cu alloy powder. X-ray diffraction (XRD) and scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) results confirm that Na2CO3 is capable of enhancing the reduction of fayaltie, copper silicate and copper sulfide, which agrees well with thermodynamic analysis. Furthermore, the reduction mechanism of copper slag was demonstrated based on systematic experimental observations.

  1. A natural analogue for copper waste canisters: The copper-uranium mineralised concretions in the Permian mudrocks of south Devon, United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Milodowski, A.E.; Styles, M.T.; Hards, V.L. [Natural Environment Research Council (United Kingdom). British Geological Survey

    2000-08-01

    mineralisation and alteration that can be related to the burial and diagenetic history of the Permian strata. The native copper mineralisation exhibits close temporal association with the formation of uraniferous and vanadiferous concretions (known as 'fish-eyes') in the same rocks. Petrographical relationships indicate that both the copper and the 'fish-eye' concretions formed during burial diagenesis but before the maximum compaction of the host mudstone and siltstone. The regional burial history Wessex Basin, indicates that the maximum compaction of the Permian strata would have been achieved by at least the end of the Lower Jurassic (possibly even in the Triassic). Therefore, the native copper mineralisation is older than 176 Ma. The native copper sheets display a complex sequence of alteration and subsequent mineral growth of minerals on their surfaces. The earliest alteration was to copper oxides - principally cuprite with minor tenorite, indicating a change to more oxidising groundwater conditions. The dissolution of native silver and the growth of fringes of copper arsenides followed this. Nickel arsenides and chalcocite, associated with the precipitation of uranium silicates occurred in the later stages of alteration. This suggests a return to a more reducing pore water environment. Again, petrographical relationships indicate that this alteration and subsequent mineralisation is geologically old (i.e. Lower Jurassic or older). Secondary malachite, intimately intergrown copper sulphate and copper oxides, copper chloride, copper-uranium arsenate and uranium vanadates have formed as late-stage alteration products of the native copper and earlier diagenetic cuprite, chalcocite, copper-nickel arsenide and uranium silicate alteration and mineralisation. This latest stage alteration is most probably attributable to near-surface weathering processes. Although the native copper is affected by corrosion, the study has shown that a significant proportion (30

  2. [Copper pathology (author's transl)].

    Science.gov (United States)

    Mallet, B; Romette, J; Di Costanzo, J D

    1982-01-30

    Copper is an essential dietary component, being the coenzyme of many enzymes with oxidase activity, e.g. ceruloplasmin, superoxide dismutase, monoamine oxidase, etc. The metabolism of copper is complex and imperfectly known. Active transport of copper through the intestinal epithelial cells involves metallothionein, a protein rich in sulfhydryl groups which also binds the copper in excess and probably prevents absorption in toxic amounts. In hepatocytes a metallothionein facilitates absorption by a similar mechanism and regulates copper distribution in the liver: incorporation in an apoceruloplasmin, storage and synthesis of copper-dependent enzymes. Metallothioneins and ceruloplasmin are essential to adequate copper homeostasis. Apart from genetic disorders, diseases involving copper usually result from hypercupraemia of varied origin. Wilson's disease and Menkes' disease, although clinically and pathogenetically different, are both marked by low ceruloplasmin and copper serum levels. The excessive liver retention of copper in Wilson's disease might be due to increased avidity of hepatic metallothioneins for copper and decreased biliary excretion through lysosomal dysfunction. Menkes' disease might be due to low avidity of intestinal and hepatic metallothioneins for copper. The basic biochemical defect responsible for these two hereditary conditions has not yet been fully elucidated.

  3. FORMATION OF LUMINESCENT OPTICAL WAVEGUIDES IN SILICATE GLASS MATRIX BY THE ION-EXCHANGE TECHNIQUE

    Directory of Open Access Journals (Sweden)

    I. A. Dyomichev

    2015-01-01

    Full Text Available We present spectra of the alkali-silicate glasses with copper ions in near-surface area, introduced by ion exchange of different temperature and duration. It is shown that the reduction of Cu2+ in the near-surface area causes existence of Cu+ and neutral atoms in glass after the ion-exchange in divalent salt. The ion-exchange itself involves only Cu+ and Na+ ions. The formation of subnanometer clusters Cun is due to neutral copper atoms staying in near-surface zone. We have shown that the waveguide layer in near-surface area, made by ion-exchange, has а visible luminescence with the excitation by UVradiation. At the same time, the contribution to luminescence is made by Cu+ ions, molecular clusters Cun and by dimers Cu+ - Cu+ . During the high-temperature ion-exchange at 600 °С the formation and destruction equilibrium shift of molecular clusters Cun can be seen. An hour ion-exchange leads to molecular clusters Cun destruction, while at time periods less than 30 min and around 18 hours it leads to the formation of Cun. The sample turns green after 18,5 hours ion-exchange showing formation of a considerable amount of divalent copper ions Cu2+ therein.

  4. [Copper IUDs (author's transl)].

    Science.gov (United States)

    Thiery, M

    1983-10-01

    Following initial development of the Grafenberg ring in the 1920's, IUDs fell into disuse until the late 1950s, when plastic devices inserted using new technology began to gain worldwide acceptance. Further research indicated that copper had a significant antifertility effect which increased with increasing surface area, and several copper IUDs were developed and adapted, including the Copper T 200, the Copper T 220C, and the Copper T 380 A, probably the most effective yet. The Gravigard and Multiload are 2 other copper devices developed according to somewhat different principles. Copper devices are widely used not so much because of their great effectiveness as because of their suitability for nulliparous patients and their ease of insertion, which minimizes risk of uterine perforation. Records of 2584 women using Copper IUDs for 7190 women-years and 956 women using devices without copper for 6059 women-years suggest that the copper devices were associated with greater effectiveness and fewer removals for complications. Research suggests that the advantages of copper IUDs become more significant with increased duration of use. Contraindications to copper devices include allergy to copper and hepatolenticular degeneration. No carcinogenic or teratogenic effect of copper devices has been found, but further studies are needed to rule out other undesirable effects. Significant modifications of copper devices in recent years have been developed to increase their effectiveness, prolong their duration of usefulness, facilitate insertion and permit insertion during abortion or delivery. The upper limit of the surface area of copper associated with increased effectiveness appears to be between 200-300 sq mm, and at some point increases in copper exposure may provoke expulsion of the IUD. The duration of fertility inhibition of copper IUDs is usually estimated at 2-3 years, but recent research indicates that it may be 6-8 years, and some devices may retain copper surface

  5. Discovery of the copper deposits with features of the Keweenawan type in the border area of Yunnan and Guizhou provinces

    Institute of Scientific and Technical Information of China (English)

    朱炳泉; 胡耀国; 张正伟; 常向阳

    2003-01-01

    There existed intense Cu anomaly on the northeastern side of the geochemical boundary with NW strike in the border area between the Yunnan and Guizhou provinces. Through field observation, ore bodies of high-grade native coppers have been found. The copper mineralization was constrained by the ancient volcanic vents of Permian basalt eruption and the overlain strata of carbonaceous argillites. Native coppers with flaky, net veined and impregnated occurrences, fine-grained tenorites and massive chalcocites widely occur in volcanic breccias, tuffs, carbonaceous-siliceous argillites and siliceous bitumen rocks with bed thickness of about 15-80 m. Cu contents vary from 0.5% to 20%. The copper mineralization was tightly related to actinolite-tremolitization, zeolitization and bituminization and involved in extensive reduction environments. Continental flood basalts erupted in mantle plume environments usually have high Cu concentrations (~170 ×10-6 in the Emeishan basalts), which provided a copper source of mineralization. Thus, metallogenesis of the native copper deposits in the Yunnan-Guizhou border area is tightly associated with intensive crust-mantle and organic-inorganic interactions. The tremolitization and chalcocitization indicate that the metallogenic temperatures are in a range of 400-100℃. The geologic background and characteristics of ore and alteration for the native copper deposits in this area are somewhat similar to those of the Keweenawan native copper deposit in Michigan, USA.

  6. Extraction of copper from an oxidized (lateritic) ore using bacterially catalysed reductive dissolution.

    Science.gov (United States)

    Nancucheo, Ivan; Grail, Barry M; Hilario, Felipe; du Plessis, Chris; Johnson, D Barrie

    2014-01-01

    An oxidized lateritic ore which contained 0.8 % (by weight) copper was bioleached in pH- and temperature-controlled stirred reactors under acidic reducing conditions using pure and mixed cultures of the acidophilic chemolithotrophic bacterium Acidithiobacillus ferrooxidans. Sulfur was provided as the electron donor for the bacteria, and ferric iron present in goethite (the major ferric iron mineral present in the ore) acted as electron acceptor. Significantly more copper was leached by bacterially catalysed reductive dissolution of the laterite than in aerobic cultures or in sterile anoxic reactors, with up to 78 % of the copper present in the ore being extracted. This included copper that was leached from acid-labile minerals (chiefly copper silicates) and that which was associated with ferric iron minerals in the lateritic ore. In the anaerobic bioreactors, soluble iron in the leach liquors was present as iron (II) and copper as copper (I), but both metals were rapidly oxidized (to iron (III) and copper (II)) when the reactors were aerated. The number of bacteria added to the reactors had a critical role in dictating the rate and yield of copper solubilised from the ore. This work has provided further evidence that reductive bioprocessing, a recently described approach for extracting base metals from oxidized deposits, has the potential to greatly extend the range of metal ores that can be biomined.

  7. Determination of chlorine in silicate rocks

    Science.gov (United States)

    Peck, L.C.

    1959-01-01

    In a rapid accurate method for the determination of chlorine in silicate rocks, the rock powder is sintered with a sodium carbonate flux containing zinc oxide and magnesium carbonate. The sinter cake is leached with water, the resulting solution is filtered, and the filtrate is acidified with nitric acid. Chlorine is determined by titrating this solution with mercuric nitrate solution using sodium nitroprusside as the indicator. The titration is made in the dark with a beam of light shining through the solution. The end point of the titration is found by visually comparing the intensity of this beam of light with that of a similar beam of light in a reference solution.

  8. Nitridosilicates - a significant extension of silicate chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Schnick, W.; Huppertz, H. [Bayreuth Univ. (Germany). Lab. fuer Anorganische Chemie

    1997-05-01

    A new dimension in silicate chemistry becomes accessible through substitution of oxygen by nitrogen. Multinary nitridosilicates, such as Ln{sub 3}Si{sub 6}N{sub 11} (Ln = La, Ce, Pr, Nd, Sm) shown on the right, are built up from SiN{sub 4} tetrahedra into network structures. Owing to the stability of the covalent Si-N bonds and the high degree of condensation, the nitridosilicates show remarkable chemical and thermal stabilities, similar to Si{sub 3}N{sub 4}. (orig.) 22 refs.

  9. Microbial dissolution of silicate materials. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Schwartzman, D. [Howard Univ., Washington, DC (United States). Dept. of Biology

    1996-03-26

    The objective of this research was to better understand the role of selected thermophilic bacteria in the colonization and dissolution of silicate minerals, with potential applications to the HDR Project. The demonstration of enhanced dissolution from microbial effects is critically dependent on providing a mineral bait within a media deficient in the critical nutrient found in the mineral (e.g., Fe). Reproducible experimental conditions in batch experiments require agitation to expose mineral powders, as well as nearly similar initial conditions for both inoculated cultures and controls. It is difficult, but not impossible to ensure reproducible conditions with microbes favoring filamentous growth habits.

  10. Demonstration of an Integrated Compliance Model for Predicting Copper Fate and Effects in DoD Harbors

    Science.gov (United States)

    2008-12-01

    phaeopigments, bacterial abundance, cyanobacteria abundance, nitrates, phosphates, silicates, nitrites, ammonia, copper complexation capacity (Cu-CC...Mussels,” Environmental Toxicology and Chemistry 24: 2365–2372. Nriagu, J. O. 1996. “A History of Global Metal Pollution,” Science 272: 223–224. Paquin

  11. LABORATORY INVESTIGATIONS OF SILICATE MUD CONTAMINATION WITH CALCIUM

    Directory of Open Access Journals (Sweden)

    Nediljka Gaurina-Međimurec

    2004-12-01

    Full Text Available The silicate-based drilling fluid is a low solids KCl/polymer system with the addition of soluble sodium or potassium silicate to enhance inhibition and wellbore stability. Silicate-based drilling fluids exhibit remarkable shale and chalk stabilizing properties, resulting in gauge hole and the formation of firm cuttings when drilling reactive shales and soft chalks. Silicates protect shales by in-situ gellation when exposed to the neutral pore fluid and precipitation, which occurs on contact with divalent ions present at the surface of the shale. Also, silicates prevent the dispersion and washouts when drilling soft chalk by reacting with the Ca2+ ions present on chalk surfaces of cutting and wellbore to form a protective film. The silicate-based drilling fluid can be used during drilling hole section through shale interbeded anhydrite formations because of its superior shale stabilizing characteristics. However, drilling through the anhydrite can decrease the silicate concentration and change rheological and filtration fluid properties. So, the critical concentration of calcium ions should be investigated by lab tests. This paper details the mechanism of shale inhibition using silicate-based drilling fluid, and presents results of lab tests conducted to ascertain the effect of Ca2+ ions on silicate level in the fluid and the fluid properties.

  12. The distribution and composition characteristics of siliceous rocks from Qinzhou Bay-Hangzhou Bay joint belt, South China: constraint on the tectonic evolution of plates in South China.

    Science.gov (United States)

    Li, Hongzhong; Zhai, Mingguo; Zhang, Lianchang; Zhou, Yongzhang; Yang, Zhijun; He, Junguo; Liang, Jin; Zhou, Liuyu

    2013-01-01

    The Qinzhou Bay-Hangzhou Bay joint belt is a significant tectonic zone between the Yangtze and Cathaysian plates, where plentiful hydrothermal siliceous rocks are generated. Here, the authors studied the distribution of the siliceous rocks in the whole tectonic zone, which indicated that the tensional setting was facilitating the development of siliceous rocks of hydrothermal genesis. According to the geochemical characteristics, the Neopalaeozoic siliceous rocks in the north segment of the Qinzhou Bay-Hangzhou Bay joint belt denoted its limited width. In comparison, the Neopalaeozoic Qinzhou Bay-Hangzhou Bay joint belt was diverse for its ocean basin in the different segments and possibly had subduction only in the south segment. The ocean basin of the north and middle segments was limited in its width without subduction and possibly existed as a rift trough that was unable to resist the terrigenous input. In the north segment of the Qinzhou Bay-Hangzhou Bay joint belt, the strata of hydrothermal siliceous rocks in Dongxiang copper-polymetallic ore deposit exhibited alternative cycles with the marine volcanic rocks, volcanic tuff, and metal sulphide. These sedimentary systems were formed in different circumstances, whose alternative cycles indicated the release of internal energy in several cycles gradually from strong to weak.

  13. The Distribution and Composition Characteristics of Siliceous Rocks from Qinzhou Bay-Hangzhou Bay Joint Belt, South China: Constraint on the Tectonic Evolution of Plates in South China

    Directory of Open Access Journals (Sweden)

    Hongzhong Li

    2013-01-01

    Full Text Available The Qinzhou Bay-Hangzhou Bay joint belt is a significant tectonic zone between the Yangtze and Cathaysian plates, where plentiful hydrothermal siliceous rocks are generated. Here, the authors studied the distribution of the siliceous rocks in the whole tectonic zone, which indicated that the tensional setting was facilitating the development of siliceous rocks of hydrothermal genesis. According to the geochemical characteristics, the Neopalaeozoic siliceous rocks in the north segment of the Qinzhou Bay-Hangzhou Bay joint belt denoted its limited width. In comparison, the Neopalaeozoic Qinzhou Bay-Hangzhou Bay joint belt was diverse for its ocean basin in the different segments and possibly had subduction only in the south segment. The ocean basin of the north and middle segments was limited in its width without subduction and possibly existed as a rift trough that was unable to resist the terrigenous input. In the north segment of the Qinzhou Bay-Hangzhou Bay joint belt, the strata of hydrothermal siliceous rocks in Dongxiang copper-polymetallic ore deposit exhibited alternative cycles with the marine volcanic rocks, volcanic tuff, and metal sulphide. These sedimentary systems were formed in different circumstances, whose alternative cycles indicated the release of internal energy in several cycles gradually from strong to weak.

  14. Silicate mineralogy at the surface of Mercury

    Science.gov (United States)

    Namur, Olivier; Charlier, Bernard

    2017-01-01

    NASA's MESSENGER spacecraft has revealed geochemical diversity across Mercury's volcanic crust. Near-infrared to ultraviolet spectra and images have provided evidence for the Fe2+-poor nature of silicate minerals, magnesium sulfide minerals in hollows and a darkening component attributed to graphite, but existing spectral data is insufficient to build a mineralogical map for the planet. Here we investigate the mineralogical variability of silicates in Mercury's crust using crystallization experiments on magmas with compositions and under reducing conditions expected for Mercury. We find a common crystallization sequence consisting of olivine, plagioclase, pyroxenes and tridymite for all magmas tested. Depending on the cooling rate, we suggest that lavas on Mercury are either fully crystallized or made of a glassy matrix with phenocrysts. Combining the experimental results with geochemical mapping, we can identify several mineralogical provinces: the Northern Volcanic Plains and Smooth Plains, dominated by plagioclase, the High-Mg province, strongly dominated by forsterite, and the Intermediate Plains, comprised of forsterite, plagioclase and enstatite. This implies a temporal evolution of the mineralogy from the oldest lavas, dominated by mafic minerals, to the youngest lavas, dominated by plagioclase, consistent with progressive shallowing and decreasing degree of mantle melting over time.

  15. Stability of foams in silicate melts

    Science.gov (United States)

    Proussevitch, Alexander A.; Sahagian, Dork L.; Kutolin, Vladislav A.

    1993-12-01

    Bubble coalescence and the spontaneous disruption of high-porosity foams in silicate melts are the result of physical expulsion of interpore melt (syneresis) leading to bubble coalescence, and diffusive gas exchange between bubbles. Melt expulsion can be achieved either along films between pairs of bubbles, or along Plateau borders which represent the contacts between 3 or more bubbles. Theoretical evaluation of these mechanisms is confirmed by experimental results, enabling us to quantify the relevant parameters and determine stable bubble size and critical film thickness in a foam as a function of melt viscosity, surface tension, and time. Foam stability is controlled primarily by melt viscosity and time. Melt transport leading to coalescence of bubbles proceeds along inter-bubble films for smaller bubbles, and along Plateau borders for larger bubbles. Thus the average bubble size accelerates with time. In silicate melts, the diffusive gas expulsion out of a region of foam is effective only for water (and even then, only at small length scales), as the diffusion of CO 2 is negligible. The results of our analyses are applicable to studies of vesicularity of lavas, melt degassing, and eruption mechanisms.

  16. Research drilling in young silicic volcanoes

    Energy Technology Data Exchange (ETDEWEB)

    Eichelberger, J.C.

    1989-06-30

    Magmatic activity, and particularly silicic magmatic activity, is the fundamental process by which continental crust forms and evolves. The transport of magma from deep crustal reservoirs to the surface is a neglected but important aspect of magmatic phenomena. It encompasses problems of eruptive behavior, hydrothermal circulation, and ore deposition, and must be understood in order to properly interpret deeper processes. Drilling provides a means for determining the relationship of shallow intrusive processes to eruption processes at young volcanoes where eruptions are best understood. Drilling also provides a means for directly observing the processes of heat and mass transfer by which recently emplaced intrusions approach equilibrium with their new environment. Drilling in the Inyo Chain, a 600-year-old chain of volcanic vents in California, has shown the close relationship of silicic eruption to shallow dike emplacement, the control of eruptive style by shallow porous-flow degassing, the origin of obsidian by welding, the development of igneous zonation by viscosity segregation, and the character and size of conduits in relation to well-understood magmatic and phreatic eruptions. 36 refs., 9 figs.

  17. Stability constants for silicate adsorbed to ferrihydrite

    DEFF Research Database (Denmark)

    Hansen, Hans Christian Bruun; Wetche, T.P.; Raulund-Rasmussen, Karsten

    1994-01-01

    experiments in 0.01 m NaNO3 electrolyte (pH 3-6). The surface equilibrium constants were calculated according to the two-layer model by Dzombak & Morel (1990). Near equilibrium between protons/hydroxyls in solution and the ferrihydrite surface was obtained within minutes while equilibration with silicate...... required days-weeks, both reactions probably being diffusion controlled. Applying the values for specific surface area and site densities for ferrihydrite used by Dzombak & Morel (1990) (600 m2 g-1, 3.4 mumole m-2) the constants pK(al)intr 6.93 +/- 0.12, pK(a2)intr = 8.72 +/- 0.17 and log K(Si) = 3.62 were...... calculated by using the FITEQL optimization routine. Use of the specific surface area actually measured (269 m2 g-1) gave a poorer fit of the experimental data. Due to the slow adsorption of silicate and hence long shaking times, changes in the surface characteristics of the ferrihydrite seem to take place...

  18. Characterization and Recovery of Valuables from Waste Copper Smelting Slag

    Science.gov (United States)

    Prince, Sarfo; Young, Jamie; Ma, Guojun; Young, Courtney

    Silicate slags produced from smelting copper concentrates contains valuables such as Cu and Fe as well as heavy metals such as Pb and As which are considered hazardous. In this paper, various slags were characterized with several techniques: SEM-MLA, XRD, TG-DTA and ICP-MS. A recovery process was developed to separate the valuables from the silicates thereby producing value-added products and simultaneously reducing environmental concerns. Results show that the major phases in air-cooled slag are fayalite and magnetite whereas the water-cooled slag is amorphous. Thermodynamic calculations and carbothermal reduction experiments indicate that most of Cu and Fe can be recovered from both types using minor amounts of lime and alumina and treating at 1350°C (1623K) or higher for 30 min. The secondary slag can be recycled to the glass and/or ceramic industries.

  19. Removal Of Volatile Impurities From Copper Concentrates

    Energy Technology Data Exchange (ETDEWEB)

    Winkel, L.; Schuler, A.; Frei, A.; Sturzenegger, M.

    2005-03-01

    To study the removal of volatile impurities from two different copper concentrates they have been heated on a thermo balance to temperatures between 900 and 1500 C. This sample treatment revealed that both concentrates undergo strong weight losses at 500 and 700 C. They were attributed to the removal of sulfur. Elemental analyses of the residues by ICP spectrometry have shown that the thermal treatment efficiently removes the volatile impurities. Already below 900 C most of the arsenic is removed by evaporation, the largest fraction of lead and zinc is removed in the temperature interval of 1300-1500 C. It was observed that quartz in the concentrate leads to the formation of a silicon-enriched phase besides a metal rich sulfide phase. The former is interpreted as an early stage of a silicate slag. Elemental analysis showed that the formation of this distinct slag phase does not hinder the efficient removal of volatile impurities. (author)

  20. Handling of Copper and Copper Oxide Nanoparticles by Astrocytes.

    Science.gov (United States)

    Bulcke, Felix; Dringen, Ralf

    2016-02-01

    Copper is an essential trace element for many important cellular functions. However, excess of copper can impair cellular functions by copper-induced oxidative stress. In brain, astrocytes are considered to play a prominent role in the copper homeostasis. In this short review we summarise the current knowledge on the molecular mechanisms which are involved in the handling of copper by astrocytes. Cultured astrocytes efficiently take up copper ions predominantly by the copper transporter Ctr1 and the divalent metal transporter DMT1. In addition, copper oxide nanoparticles are rapidly accumulated by astrocytes via endocytosis. Cultured astrocytes tolerate moderate increases in intracellular copper contents very well. However, if a given threshold of cellular copper content is exceeded after exposure to copper, accelerated production of reactive oxygen species and compromised cell viability are observed. Upon exposure to sub-toxic concentrations of copper ions or copper oxide nanoparticles, astrocytes increase their copper storage capacity by upregulating the cellular contents of glutathione and metallothioneins. In addition, cultured astrocytes have the capacity to export copper ions which is likely to involve the copper ATPase 7A. The ability of astrocytes to efficiently accumulate, store and export copper ions suggests that astrocytes have a key role in the distribution of copper in brain. Impairment of this astrocytic function may be involved in diseases which are connected with disturbances in brain copper metabolism.

  1. Petrophysical Analysis of Siliceous Ooze Sediments, Ormen Lange Field, Norway

    DEFF Research Database (Denmark)

    Awedalkarim, Ahmed; Fabricius, Ida Lykke

    Skeletal remains of siliceous algae form biogenic fine grained highly porous pelagic siliceous ooze sediments that were found above the reservoir of the Ormen Lange gas field which is located in the southern part of the Norwegian Sea (Figure 1a). The Palaeocene sandstone of the “Egga” Formation i...

  2. Silicate Adsorption in Paddy Soils of Guangdong Province, China

    Institute of Scientific and Technical Information of China (English)

    HUANG Li-Yuan; LI Hua-Xing; ZHANG Xin-Ming; LU Wei-Sheng; LIU Yuan-Jin

    2006-01-01

    Silicate adsorption in eight paddy soils developed from four different parent materials in Guangdong Province, China was examined to obtain fundamental knowledge of silicate adsorption to improve the efficacy of silicate fertilizer use in these areas. A correlation analysis showed that silicate adsorption did not obey the Langmuir equation (r = -0.664-0.301) but did obey the Freundlich and Temkin equations (P ≤ 0.01, r = 0.885-0.990). When the equilibrium silicate concentration (Ci) was less than 45 mg SiO2 kg-1, the adsorption capacity was in the following decreasing order of paddy soils: basalt-derived > Pearl River Delta sediment-derived > granite-derived > sand-shale-derived. Stepwise regression and path analysis showed that for the investigated paddy soils amorphous MnO and Al2O3 were the two most important materials that affected silicate adsorption. Moreover, as Ci increased, amorphous Al2O3 tended to play a more important role in silicate adsorption, while the effects of amorphous MnO on silicate adsorption tended to decrease.

  3. Crystalline silicates in AGB and post-AGB stars

    NARCIS (Netherlands)

    Waters, LBFM; Molster, FJ; LeBertre, T; Lebre, A; Waelkens, C

    1999-01-01

    We discuss ISO spectroscopy of oxygen-rich dust shells surrounding evolved stars. The dust that condenses in the outflows of stars on the Asymptotic Giant Branch consists mainly of amorphous silicates and simple oxides. For high mass loss rates, crystalline silicates begin to appear at modest abunda

  4. The shape and composition of interstellar silicate grains

    NARCIS (Netherlands)

    Min, M.; Waters, L.B.F.M.; de Koter, A.; Hovenier, J.W.; Keller, L.P.; Markwick-Kemper, F.

    2007-01-01

    We investigate the composition and shape distribution of silicate dust grains in the interstellar medium. The effects of the amount of magnesium and iron in the silicate lattice are studied in detail. We fit the spectral shape of the interstellar 10 mu m extinction feature as observed towards the ga

  5. The shape and composition of interstellar silicate grains

    NARCIS (Netherlands)

    Min, M.; Waters, L.B.F.M.; de Koter, A.; Hovenier, J.W.; Keller, L.P.; Markwick-Kemper, F.

    2007-01-01

    We investigate the composition and shape distribution of silicate dust grains in the interstellar medium. The effects of the amount of magnesium and iron in the silicate lattice are studied in detail. We fit the spectral shape of the interstellar 10 mu m extinction feature as observed towards the

  6. Canine models of copper toxicosis for understanding mammalian copper metabolism

    OpenAIRE

    Fieten, Hille; Leegwater, Peter A. J.; Watson, Adrian L.; Rothuizen, Jan

    2011-01-01

    Hereditary forms of copper toxicosis exist in man and dogs. In man, Wilson’s disease is the best studied disorder of copper overload, resulting from mutations in the gene coding for the copper transporter ATP7B. Forms of copper toxicosis for which no causal gene is known yet are recognized as well, often in young children. Although advances have been made in unraveling the genetic background of disorders of copper metabolism in man, many questions regarding disease mechanisms and copper homeo...

  7. Optical Properties of Astronomical Silicates in the Far-infrared

    Science.gov (United States)

    Rinehart, Stephen A,; Benford, Dominic J.; Dwek, Eli; Henry, Ross M.; Nuth, Joseph A., III; Silverberg, Robert f.; Wollack, Edward J.

    2008-01-01

    Correct interpretation of a vast array of astronomical data relies heavily on understanding the properties of silicate dust as a function of wavelength, temperature, and crystallinity. We introduce the QPASI-T (Optical Properties of Astronomical Silicates with Infrared Techniques) project to address the need for high fidelity optical characterization data on the various forms of astronomical dust. We use two spectrometers to provide extinction data for silicate samples across a wide wavelength range (from the near infrared to the millimeter). New experiments are in development that will provide complementary information on the emissivity of our samples, allowing us to complete the optical characterization of these dust materials. In this paper, we present initial results from several materials including amorphous iron silicate, magnesium silicate and silica smokes, over a wide range of temperatures, and discuss the design and operation of our new experiments.

  8. Hair copper in intrauterine copper device users.

    Science.gov (United States)

    Thiery, M; Heyndrickx, A; Uyttersprot, C

    1984-03-01

    The antifertility effect of copper-bearing IUDs is based on continuous release of copper, which is a result of the reaction between the metal and the uterine secretions. Released cupric ions collect in the endometrium and in the uterine fluid but significant accumulation has not been found in the bloodstream or elsewhere. Following Laker's suggestion that hair be used for monitoring essential trace elements, e.g., copper, we checked the copper content of the hair of women wearing copper-bearing IUDs. Samples of untreated pubic hair removed by clipping before diagnostic curettage were obtained from 10 young (24-34 years old), white caucasian females who until then had been wearing an MLCu250 IUD for more than 1 year. Pubes from 10 comparable (sex, age, race) subjects who had never used a Cu-containing device served as controls. The unwashed material was submitted to the toxicology laboratory, where the copper content was assessed by flameless atomic absorption, a technique whose lower limit of measurement lies at a concentration of 0.05 mcg Cu/ml fluid (50 ppb). Hair samples were washed to remove extraneous traces of metal according to the prescriptions of the International Atomic Energy Agency, weighed, and mineralized, after which a small volume (10 mcl) of the diluted fluid was fed into the graphite furnace. Each sample (75-150 mg) was analyzed 4 times, both before and after washing. Since the cleaning procedure reduces the weight of the sample (mainly by the removal of fat, dust, etc.) this explains why the percentage copper content of washed hair is higher than that of unwashed hair belonging to the same subject. The results indicate that there was no significant difference (Mann-Whitney U test) between the mean copper levels of both unwashed and washed pubes from women who were using or had never used an MLCu250 IUD. We therefore conclude that the use of this copper-containing device is not associated with significant accumulation of copper in (pubic) hair.

  9. China Copper Processing Industry Focus

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    <正>1. Market Consumption The ’China Factor’ and Copper Price Fluctuation We all know China is an enormous consumer of copper,but the exact levels of consumption and where the copper has gone remains a mystery.

  10. Biogenic nanoparticles: copper, copper oxides, copper sulphides, complex copper nanostructures and their applications.

    Science.gov (United States)

    Rubilar, Olga; Rai, Mahendra; Tortella, Gonzalo; Diez, Maria Cristina; Seabra, Amedea B; Durán, Nelson

    2013-09-01

    Copper nanoparticles have been the focus of intensive study due to their potential applications in diverse fields including biomedicine, electronics, and optics. Copper-based nanostructured materials have been used in conductive films, lubrification, nanofluids, catalysis, and also as potent antimicrobial agent. The biogenic synthesis of metallic nanostructured nanoparticles is considered to be a green and eco-friendly technology since neither harmful chemicals nor high temperatures are involved in the process. The present review discusses the synthesis of copper nanostructured nanoparticles by bacteria, fungi, and plant extracts, showing that biogenic synthesis is an economically feasible, simple and non-polluting process. Applications for biogenic copper nanoparticles are also discussed.

  11. Organic modification of layered silicates. Structural and thermal characterizations

    Energy Technology Data Exchange (ETDEWEB)

    Prado, L.A.S. de A.; Schulte, K. [Polymer Composites, Denickstrasse 15, TU Hamburg-Harburg, D-21073 Hamburg (Germany); Karthikeyan, C.S.; Nunes, S.P. [Institute of Chemistry, GKSS Research Centre, Max-Planck Strasse 1, D-21502 Geesthacht (Germany); De Torriani, Iris L. [Instituto de Fisica Gleb Wataghin, Universidade Estadual de Campinas, Cidade Universitaria Zeferino Vaz, CEP 13083-970, Campinas-SP (Brazil)

    2005-05-01

    Organic modification of natural and synthetic layered silicates namely montmorillonite and laponite is reported in this work. The modified silicates are being subsequently used in the preparation of nano-composite membranes based on ionomers for fuel cells application. Laponite, an entirely synthetic silicate, was modified using organosiloxanes containing imidazole groups. Two different strategies were adopted for modification: (a) swelling of the silicate in 2-butanone followed by functionalization using the siloxane at room temperature, (b) direct reaction between laponite and the organosiloxane in xylene at 120{sup o}C. Montmorillonite, a natural silicate, was supplied in the alkyl-ammonium form containing -OH groups. The modification of this silicate was conducted following the procedure (b). The structures of both plain and modified silicates were investigated by XRD showing that the interlayer distance (around 17A) was not affected during the functionalization of laponite. However, a noticeable increase in the interlayer distance from 18.0A to 24.5A was observed for the modified montmorillonite. This clearly shows the presence of polysiloxane chains in between the silicate layers. Further characterization showed that the modification of these silicates was in the range between 16% and 23% (molar percentage). TGA was done between 25 and 300{sup o}C in order to study the thermal degradation pattern of the silicates. The amount of adsorbed water could be determined from the results. The functionalization reduced the adsorption of water from 13.5% to 6.8% for laponite and from 8.5% to 4% for montmorillonite.

  12. Disordered Silicates in Space: a Study of Laboratory Spectra of "Amorphous" Silicates

    CERN Document Server

    Speck, Angela K; Hofmeister, Anne M

    2011-01-01

    We present a laboratory study of silicate glasses of astrophysically relevant compositions including olivines, pyroxenes and melilites. With emphasis on the classic Si-O stretching feature near 10 microns, we compare infrared spectra of our new samples with laboratory spectra on ostensibly similar compositions, and also with synthetic silicate spectral data commonly used in dust modeling. Several different factors affect spectral features including sample chemistry (e.g., polymerization, Mg/Fe ratio, oxidation state and Al-content) and different sample preparation techniques lead to variations in porosity, density and water content. The convolution of chemical and physical effects makes it difficult to attribute changes in spectral parameters to any given variable. It is important that detailed chemical and structural characterization be provided along with laboratory spectra. In addition to composition and density, we measured the glass transition temperatures for the samples which place upper limits on the ...

  13. Vibrational spectra of copper polysilicate, CuSiO3

    OpenAIRE

    2009-01-01

    This is a representation of the first Raman and IR / FIR spectra for orthorhombic copper polysilicate, CuSiO3, measured at room temperature on polycrystalline samples and a comparison of the optical phonons with those observed for the spin-Peierls compound CuGeO3. CuSiO3 represents a further example of a quasi-one-dimensional spin = 1/2 antiferromagnetic Heisenberg chain system. A mode assignment for the silicate is given. From the analysis of the Davydov doublets a reduced intralayer- to-int...

  14. Interstellar Silicate Dust in the z=0.89 Absorber Towards PKS 1830-211: Crystalline Silicates at High Redshift?

    CERN Document Server

    Aller, Monique C; York, Donald G; Vladilo, Giovanni; Welty, Daniel E; Som, Debopam

    2012-01-01

    We present evidence of a >10-sigma detection of the 10 micron silicate dust absorption feature in the spectrum of the gravitationally lensed quasar PKS 1830-211, produced by a foreground absorption system at redshift 0.886. We have examined more than 100 optical depth templates, derived from both observations of Galactic and extragalactic sources and laboratory measurements, in order to constrain the chemical structure of the silicate dust. We find that the best fit to the observed absorption profile is produced by laboratory crystalline olivine, with a corresponding peak optical depth of tau_10=0.27+/-0.05. The fit is slightly improved upon by including small contributions from additional materials such as silica, enstatite, or serpentine, which suggests that the dust composition may consist of a blend of crystalline silicates. Combining templates for amorphous and crystalline silicates, we find that the fraction of crystalline silicates needs to be at least 95%. Given the rarity of extragalactic sources wit...

  15. INTERSTELLAR SILICATE DUST IN THE z = 0.89 ABSORBER TOWARD PKS 1830-211: CRYSTALLINE SILICATES AT HIGH REDSHIFT?

    Energy Technology Data Exchange (ETDEWEB)

    Aller, Monique C.; Kulkarni, Varsha P.; Som, Debopam [Department of Physics and Astronomy, University of South Carolina, 712 Main Street, Columbia, SC 29208 (United States); York, Donald G.; Welty, Daniel E. [Department of Astronomy and Astrophysics, University of Chicago, 5640 S. Ellis Ave., Chicago, IL 60637 (United States); Vladilo, Giovanni, E-mail: ALLERM@mailbox.sc.edu [Osservatorio Astonomico di Trieste, Via Tiepolo 11, 34143 Trieste (Italy)

    2012-03-20

    We present evidence of a >10{sigma} detection of the 10 {mu}m silicate dust absorption feature in the spectrum of the gravitationally lensed quasar PKS 1830-211, produced by a foreground absorption system at redshift 0.886. We have examined more than 100 optical depth templates, derived from both observations of Galactic and extragalactic sources and laboratory measurements, in order to constrain the chemical structure of the silicate dust. We find that the best fit to the observed absorption profile is produced by laboratory crystalline olivine, with a corresponding peak optical depth of {tau}{sub 10} = 0.27 {+-} 0.05. The fit is slightly improved upon by including small contributions from additional materials, such as silica, enstatite, or serpentine, which suggests that the dust composition may consist of a blend of crystalline silicates. Combining templates for amorphous and crystalline silicates, we find that the fraction of crystalline silicates needs to be at least 95%. Given the rarity of extragalactic sources with such a high degree of silicate crystallinity, we also explore the possibility that the observed spectral features are produced by amorphous silicates in combination with other molecular or atomic transitions, or by foreground source contamination. While we cannot rule out these latter possibilities, they lead to much poorer profile fits than for the crystalline olivine templates. If the presence of crystalline interstellar silicates in this distant galaxy is real, it would be highly unusual, given that the Milky Way interstellar matter contains essentially only amorphous silicates. It is possible that the z = 0.886 absorber toward PKS 1830-211, well known for its high molecular content, has a unique star-forming environment that enables crystalline silicates to form and prevail.

  16. Behavior of calcium silicate hydrate in aluminate solution

    Institute of Scientific and Technical Information of China (English)

    LI Xiao-bin; ZHAO Zhuo; LIU Gui-hua; ZHOU Qiu-sheng; PENG Zhi-hong

    2005-01-01

    Using calcium hydroxide and sodium silicate as starting materials, two kinds of calcium silicate hydrates, CaO · SiO2 · H2O and 2CaO · SiO2 · 1.17H2O, were hydro-thermally synthesized at 120 ℃. The reaction rule of calcium silicate hydrate in aluminate solution was investigated. The result shows that CaO · SiO2 · H2O is more stable than 2CaO · SiO2 · 1.17H2 O in aluminate solution and its stability increases with the increase of reaction temperature but decreases with the increase of caustic concentration. The reaction between calcium silicate hydrate and aluminate solution is mainly through two routes. In the first case, Al replaces partial Si in calcium silicate hydrate, meanwhile 3CaO · Al2 O3 · xSiO2 · (6-2x) H2 O (hydro-garnet) is formed and some SiO2 enters the solution. In the second case, calcium silicate hydrate can react directly with aluminate solution, forming hydro-garnet and Na2O · Al2O3 · 2SiO2 · nH2O (DSP). The desilication reaction of aluminate solution containing silicate could contribute partially to forming DSP.

  17. Deep ocean biogeochemistry of silicic acid and nitrate

    Science.gov (United States)

    Sarmiento, J. L.; Simeon, J.; Gnanadesikan, A.; Gruber, N.; Key, R. M.; Schlitzer, R.

    2007-03-01

    Observations of silicic acid and nitrate along the lower branch of the global conveyor belt circulation show that silicic acid accumulation by diatom opal dissolution occurs at 6.4 times the rate of nitrate addition by organic matter remineralization. The export of opal and organic matter from the surface ocean occurs at a Si:N mole ratio that is much smaller than this almost everywhere (cf. Sarmiento et al., 2004). The preferential increase of silicic acid over nitrate as the deep circulation progresses from the North Atlantic to the North Pacific is generally interpreted as requiring deep dissolution of opal together with shallow remineralization of organic matter (Broecker, 1991). However, Sarmiento et al. (2004) showed that the primary reason for the low silicic acid concentration of the upper ocean is that the waters feeding the main thermocline from the surface Southern Ocean are depleted in silicic acid relative to nitrate. By implication, the same Southern Ocean processes that deplete the silicic acid in the surface Southern Ocean must also be responsible for the enhanced silicic acid concentration of the deep ocean. We use observations and results from an updated version of the adjoint model of Schlitzer (2000) to confirm that this indeed the case.

  18. The shape and composition of interstellar silicate grains

    CERN Document Server

    Min, M; De Koter, A; Hovenier, J W; Keller, L P; Markwick-Kemper, F

    2006-01-01

    We investigate the composition and shape distribution of silicate dust grains in the interstellar medium. The effect of the amount of magnesium in the silicate lattice is studied. We fit the spectral shape of the interstellar 10 mu extinction feature as observed towards the galactic center. We use very irregularly shaped coated and non-coated porous Gaussian Random Field particles as well as a statistical approach to model shape effects. For the dust materials we use amorphous and crystalline silicates with various composition and SiC. The results of our analysis of the 10 mu feature are used to compute the shape of the 20 mu silicate feature and to compare this with observations. By using realistic particle shapes we are, for the first time, able to derive the magnesium fraction in interstellar silicates. We find that the interstellar silicates are highly magnesium rich (Mg/(Fe+Mg)>0.9) and that the stoichiometry lies between pyroxene and olivine type silicates. This composition is not consistent with that o...

  19. Reagentless and calibrationless silicate measurement in oceanic waters.

    Science.gov (United States)

    Giraud, William; Lesven, Ludovic; Jońca, Justyna; Barus, Carole; Gourdal, Margaux; Thouron, Danièle; Garçon, Véronique; Comtat, Maurice

    2012-08-15

    Determination of silicate concentration in seawater without addition of liquid reagents was the key prerequisite for developing an autonomous in situ electrochemical silicate sensor (Lacombe et al., 2007) [11]. The present challenge is to address the issue of calibrationless determination. To achieve such an objective, we chose chronoamperometry performed successively on planar microelectrode (ME) and ultramicroelectrode (UME) among the various possibilities. This analytical method allows estimating simultaneously the diffusion coefficient and the concentration of the studied species. Results obtained with ferrocyanide are in excellent agreement with values of the imposed concentration and diffusion coefficient found in the literature. For the silicate reagentless method, successive chronoamperometric measurements have been performed using a pair of gold disk electrodes for both UME and ME. Our calibrationless method was tested with different concentrations of silicate in artificial seawater from 55 to 140×10(-6) mol L(-1). The average value obtained for the diffusion coefficient of the silicomolybdic complex is 2.2±0.4×10(-6) cm(2) s(-1), consistent with diffusion coefficient values of molecules in liquid media. Good results were observed when comparing known concentration of silicate with experimentally derived ones. Further work is underway to explore silicate determination within the lower range of oceanic silicate concentration, down to 0.1×10(-6) mol L(-1). Copyright © 2012 Elsevier B.V. All rights reserved.

  20. Copper and silver halates

    CERN Document Server

    Woolley, EM; Salomon, M

    2013-01-01

    Copper and Silver Halates is the third in a series of four volumes on inorganic metal halates. This volume presents critical evaluations and compilations for halate solubilities of the Group II metals. The solubility data included in this volume are those for the five compounds, copper chlorate and iodate, and silver chlorate, bromate and iodate.

  1. Coping with copper

    DEFF Research Database (Denmark)

    Nunes, Ines; Jacquiod, Samuel; Brejnrod, Asker

    2016-01-01

    Copper has been intensively used in industry and agriculture since mid-18(th) century and is currently accumulating in soils. We investigated the diversity of potential active bacteria by 16S rRNA gene transcript amplicon sequencing in a temperate grassland soil subjected to century-long exposure......, suggesting a potential promising role as bioindicators of copper contamination in soils....

  2. Cytotoxicity and physical properties of tricalcium silicate-based endodontic materials

    Directory of Open Access Journals (Sweden)

    Young-Eun Jang

    2014-05-01

    Full Text Available Objectives The aim of this study was to evaluate the cytotoxicity, setting time and compressive strength of MTA and two novel tricalcium silicate-based endodontic materials, Bioaggregate (BA and Biodentine (BD. Materials and Methods Cytotoxicity was evaluated by using a 2,3-bis(2-methoxy-4-nitro-5-sulfophenyl-5-((phenylaminocarbonyl-2H-tetrazolium hydroxide (XTT assay. Measurements of 9 heavy metals (arsenic, cadmium, chromium, copper, iron, lead, manganese, nickel, and zinc were performed by inductively coupled plasma-mass spectrometry (ICP-MS of leachates obtained by soaking the materials in distilled water. Setting time and compressive strength tests were performed following ISO requirements. Results BA had comparable cell viability to MTA, whereas the cell viability of BD was significantly lower than that of MTA. The ICP-MS analysis revealed that BD released significantly higher amount of 5 heavy metals (arsenic, copper, iron, manganese, and zinc than MTA and BA. The setting time of BD was significantly shorter than that of MTA and BA, and the compressive strength of BA was significantly lower than that of MTA and BD. Conclusions BA and BD were biocompatible, and they did not show any cytotoxic effects on human periodontal ligament fibroblasts. BA showed comparable cytotoxicity to MTA but inferior physical properties. BD had somewhat higher cytotoxicity but superior physical properties than MTA.

  3. Cytotoxicity and physical properties of tricalcium silicate-based endodontic materials

    Science.gov (United States)

    Jang, Young-Eun; Lee, Bin-Na; Koh, Jeong-Tae; Park, Yeong-Joon; Joo, Nam-Eok; Chang, Hoon-Sang; Hwang, In-Nam; Oh, Won-Mann

    2014-01-01

    Objectives The aim of this study was to evaluate the cytotoxicity, setting time and compressive strength of MTA and two novel tricalcium silicate-based endodontic materials, Bioaggregate (BA) and Biodentine (BD). Materials and Methods Cytotoxicity was evaluated by using a 2,3-bis(2-methoxy-4-nitro-5-sulfophenyl)-5-((phenylamino)carbonyl)-2H-tetrazolium hydroxide (XTT) assay. Measurements of 9 heavy metals (arsenic, cadmium, chromium, copper, iron, lead, manganese, nickel, and zinc) were performed by inductively coupled plasma-mass spectrometry (ICP-MS) of leachates obtained by soaking the materials in distilled water. Setting time and compressive strength tests were performed following ISO requirements. Results BA had comparable cell viability to MTA, whereas the cell viability of BD was significantly lower than that of MTA. The ICP-MS analysis revealed that BD released significantly higher amount of 5 heavy metals (arsenic, copper, iron, manganese, and zinc) than MTA and BA. The setting time of BD was significantly shorter than that of MTA and BA, and the compressive strength of BA was significantly lower than that of MTA and BD. Conclusions BA and BD were biocompatible, and they did not show any cytotoxic effects on human periodontal ligament fibroblasts. BA showed comparable cytotoxicity to MTA but inferior physical properties. BD had somewhat higher cytotoxicity but superior physical properties than MTA. PMID:24790920

  4. Cytotoxicity and physical properties of tricalcium silicate-based endodontic materials.

    Science.gov (United States)

    Jang, Young-Eun; Lee, Bin-Na; Koh, Jeong-Tae; Park, Yeong-Joon; Joo, Nam-Eok; Chang, Hoon-Sang; Hwang, In-Nam; Oh, Won-Mann; Hwang, Yun-Chan

    2014-05-01

    The aim of this study was to evaluate the cytotoxicity, setting time and compressive strength of MTA and two novel tricalcium silicate-based endodontic materials, Bioaggregate (BA) and Biodentine (BD). Cytotoxicity was evaluated by using a 2,3-bis(2-methoxy-4-nitro-5-sulfophenyl)-5-((phenylamino)carbonyl)-2H-tetrazolium hydroxide (XTT) assay. Measurements of 9 heavy metals (arsenic, cadmium, chromium, copper, iron, lead, manganese, nickel, and zinc) were performed by inductively coupled plasma-mass spectrometry (ICP-MS) of leachates obtained by soaking the materials in distilled water. Setting time and compressive strength tests were performed following ISO requirements. BA had comparable cell viability to MTA, whereas the cell viability of BD was significantly lower than that of MTA. The ICP-MS analysis revealed that BD released significantly higher amount of 5 heavy metals (arsenic, copper, iron, manganese, and zinc) than MTA and BA. The setting time of BD was significantly shorter than that of MTA and BA, and the compressive strength of BA was significantly lower than that of MTA and BD. BA and BD were biocompatible, and they did not show any cytotoxic effects on human periodontal ligament fibroblasts. BA showed comparable cytotoxicity to MTA but inferior physical properties. BD had somewhat higher cytotoxicity but superior physical properties than MTA.

  5. Fungicides and silicate clay on the control of antracnosis in yellow passionfruitFungicidas e argila silicatada no controle da antracnose do maracujá amarelo

    Directory of Open Access Journals (Sweden)

    Luiz Augusto Martins Peruch

    2012-10-01

    Full Text Available The anthracnose, caused by Glomerella cingulata (anamorf Colletotrichum gloeosporioides, is the most important fungal disease for aerial parts of yellow passionfruit. However, few studies about anthracnose control in field conditions have been published. The objective of this research was to evaluate silicate clay and fungicides for anthracnose control. Treatments evaluated were: tebuconazole (20g i.a./100L, copper oxychloride (180g i.a./100L, silicate clay (15g /L and control (untreated plants. The sanity of the plants was evaluated through area under disease progress curve (AUCPD, final severity (SEVF and disease progress curves. Experimental design was completely randomized with five repetitions. Tebuconazole and silicate clay proportioned significant reduction for AUCPD and SEVF compared to control. Copper oxychloride reduced only SEVF. Treatment with tebuconazole reduced AUCPD and SEVF in 75% and 71%, and silicate clay in 82%, respectively. Copper oxychloride reduced SEVF in 76%. The disease progress curves confirmed results and showed lower growth of anthracnose for tebuconazole and silicate clay. Silicate clay and tebuconazole are efficient to control anthracnose in passionfruit. A antracnose, causada por Glomerella cingulata (anamorfo Colletotrichum gloesporioides, é a principal doença fúngica de parte aérea do maracujazeiro amarelo. Todavia, poucos estudos de controle da doença a campo têm sido publicados, motivo pelo qual é importante avaliar diferentes fungicidas e substâncias alternativas para o manejo da antracnose. Neste trabalho foram avaliados os seguintes tratamentos: tebuconazole (20g i.a./100L, oxicloreto de cobre (180g i.a./100L, argila silicatada (15g /L e testemunha. A partir da avaliação da severidade da doença, determinou-se a área abaixo da curva de progresso da doença (AACPD, severidade final (SEVF e as curvas de progresso da doença. O delineamento adotado foi inteiramente casualizado com cinco repeti

  6. Investigation of Copper Ammonia Leaching from Smelter Slags: Characterization, Leaching and Kinetics

    Science.gov (United States)

    Bidari, Ehsan; Aghazadeh, Valeh

    2015-10-01

    Although ammonia leaching of copper from slags has been reported generally as a part of copper slag utilization methods, but no detailed studies have been reported in the literature. In this research, we tried to investigate the effect of different parameters on ammonia leaching of copper from copper smelting slag by identifying different copper-bearing phases and following them during leaching time. Mineralogical characterization of the smelting slag (1.7 pct Cu) was done using X-ray fluorescence, X-ray diffraction, optical microscopy, diagnostic leaching tests, and scanning electron microscopy. The characterization studies indicated that main copper-bearing species are soluble copper oxides and chalcocite along with minor amount of covellite, bornite, blister copper particles, and chalcopyrite. It was also found that only approximately 0.2 pct Cu was present in the insoluble bulk silicate phases. These results suggest that approximately 88 pct of the total copper of slag could be extracted by ammonia sulfide leaching. Leaching tests were carried out and the effects of various parameters, namely pH, ammonia concentration, temperature, presence of oxygen, stirring speed, and pulp density were examined on copper leaching. The temperature and stirring speed had the most pronounced effect on the copper leaching, whereas ammonia affected the leaching yield at low concentrations of ammonia. It was found that 78 pct of Cu could be extracted within 4 hours and under optimum conditions: T = 343 K (70 °C), 2M ammonia, pH 10.5, stirring speed = 900 rpm, pulp density = 10 pct ( w s/ v). The kinetic data were analyzed with the shrinking core models, and it was found that the leaching process is controlled by both the interfacial transfer and diffusion across the product layer and the activation energy is calculated to be 49.4 kJ mol-1.

  7. Functional substitution of coordination polyhedron in crystal structure of silicates

    Institute of Scientific and Technical Information of China (English)

    叶大年; 马哲生; 赫伟; 李哲; 施倪承; D.Pushcharovsky

    2002-01-01

    On the bases of the study of comparative crystal chemistry of silicates it has been concluded that the octahedra and square pyramids of Ti-0 and Zr-O play functional role of tetrahedra of Si-O in the construction of crystal structures. Therefore, those silicates may be named titano-and zircono-silicates. Because of the functional similarity of coordination polyhedra, the structures of cristobalite and feldspar have been compared with those of perovskite and garnet, respectively. As a new concept, the functional replacement of tetrahedra by octahedra and/or pyramids is defined by the authors of this paper for favorable comparison of relative crystal structures.

  8. Sensitized photoluminescence of erbium silicate synthesized on porous silicon framework

    Science.gov (United States)

    Shen, Hao; Xu, Lingbo; Li, Dongsheng; Yang, Deren

    2017-09-01

    Er silicate/porous silicon (PS) composites with effective sensitized erbium emission at 1.53 μm have been synthesized on the PS framework. Cross-sectional scanning electron microscopy and X-ray diffraction reveal that the PS is coated by Er silicate in composites. Indirect excitation of Er3+ ion luminescence via energy transfer from PS is confirmed. The temperature dependence of Er-related photoluminescence intensity and lifetime is investigated, which concludes a phonon-mediated energy transfer process. The combination of the PS framework and Er silicate provides a possible strategy for practical silicon-based light sources.

  9. Fire Resistance of Wood Impregnated with Soluble Alkaline Silicates

    Directory of Open Access Journals (Sweden)

    Carlos Alberto Giudice

    2007-01-01

    Full Text Available The aim of this paper is to determine the fire performance of wood panels (Araucaria angustifolia impregnated with soluble alkaline silicates. Commercial silicates based on sodium and potassium with 2.5/1.0 and 3.0/1.0 silica/alkali molar ratios were selected; solutions and glasses were previously characterized. Experimental panels were tested in a limiting oxygen chamber and in a two-foot tunnel. Results displayed a high fire-retardant efficiency using some soluble silicates.

  10. Journal of the Chinese Silicate Society (Selected Articles).

    Science.gov (United States)

    2014-09-26

    A-A157 497 JOURNAL OF THE CHINESE SILICATE SOCIETY (SELECTED i/i ARTICLES)(U) FOREIGN TECHNOLOGY DIV IWRIGHT-PRT RSON U CLSS..AFE OH 11 JUN 85...7 V- V 17 -, 7Z I T7. k. V.-.’.~. W ~ . FTD-ID(RS)T-0160-85 FOREIGN TECHNOLOGY DIVISION JOURNAL OF THE CHINESE SILICATE SOCIETY... JOURNAL OF THE CHINESE SILICATE SOCIETY D- At"Ibutilonf (Selected Articles) Availability Cadm English pages: 28 Dist ’Avail ald/zr Source: Guisuanyan

  11. Kunpeng Copper:The largest Copper Smelting Company of Sichuan

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>On September 9,Liangshan Mining Company’s 100,000 tons/year cathode copper project kicked off.It is another key project of the company following the successful launch of the 100,000 tons/year anode copper project.Based on ISA copper smelting technology of the largest open-cast copper mine in southwest China,

  12. Posttranslational regulation of copper transporters

    NARCIS (Netherlands)

    van den Berghe, P.V.E.

    2009-01-01

    The transition metal copper is an essential cofactor for many redox-active enzymes, but excessive copper can generate toxic reactive oxygen species. Copper homeostasis is maintained by highly conserved proteins, to balance copper uptake, distribution and export on the systemic and cellular level. Th

  13. Exfoliation of Egyptian Blue and Han Blue, two alkali earth copper silicate-based pigments.

    Science.gov (United States)

    Johnson-McDaniel, Darrah; Salguero, Tina T

    2014-04-24

    In a visualized example of the ancient past connecting with modern times, we describe the preparation and exfoliation of CaCuSi4O10 and BaCuSi4O10, the colored components of the historic Egyptian blue and Han blue pigments. The bulk forms of these materials are synthesized by both melt flux and solid-state routes, which provide some control over the crystallite size of the product. The melt flux process is time intensive, but it produces relatively large crystals at lower reaction temperatures. In comparison, the solid-state method is quicker yet requires higher reaction temperatures and yields smaller crystallites. Upon stirring in hot water, CaCuSi4O10 spontaneously exfoliates into monolayer nanosheets, which are characterized by TEM and PXRD. BaCuSi4O10 on the other hand requires ultrasonication in organic solvents to achieve exfoliation. Near infrared imaging illustrates that both the bulk and nanosheet forms of CaCuSi4O10 and BaCuSi4O10 are strong near infrared emitters. Aqueous CaCuSi4O10 and BaCuSi4O10 nanosheet dispersions are useful because they provide a new way to handle, characterize, and process these materials in colloidal form.

  14. Report on exploration of the Wadi Yiba copper prospect, Tihamat Ash Sham quadrangle, Kingdom of Saudi Arabia

    Science.gov (United States)

    Earhart, Robert L.

    1969-01-01

    The first phase of an exploration program at The Wadi Yiba copper prospect consisted of geologic mapping, prospecting, sampling, geophysical surveys, and diamond drilling. Copper mineralization is in a sedimentary rock sequence comprised mostly of siliceous, calcareous, and dolomitic rocks metamorphosed to the greenschist facies. The metasedimentary rocks are overlain and underlain by metavolcanic rocks. They are folded into a tight north-plunging syncline transected by two fault systems. Results from the exploration program indicate that a fault zone which sub-parallels the synclinal axis and cuts siliceous dolomite contains copper mineralization and small amounts of gold and silver. Copper and silver beaming pyroclastic rocks were found in the upper part of the metasedimentary rock sequence. Concentrations of copper mineralization seem to be restricted to particular rock units in the metasedimentary rock sequence. Primary sulfides have not been encountered in the drill holes to date and the results from one drill hole indicate secondary copper sulfide minerals to a vertical depth of 60 meters. Further exploration seems to be warranted and a program is proposed which includes the investigation of other mineral occurrences and geophysical anomalies in the region.

  15. Viscosity model for fully liquid silicate melt

    Directory of Open Access Journals (Sweden)

    Zhang Guo-Hua

    2012-01-01

    Full Text Available A model for estimating the viscosity of silicate melt as derived in our previous paper is extended to the system containing MgO, CaO, SrO, BaO, Li2O, Na2O, K2O, which can express the nonlinear variation of activation energy of viscosity with the composition. It is found that the optimized parameters of model which characterize the deforming ability of bonds around non-bridging oxygen decrease with increasing the bond strength of M-O bond expressed by I=2Q/RMz+ + rO2-2 (where Q is the valence of cation M; r is the radius. It is pointed out that viscosity is not only determined by the bond strength, but also by the radius of cation which is defined as the size effect. The radius of cation plays paradox roles in the two factors: smaller radius leads to a stronger bond, thus a higher viscosity; while cations with smaller radius are easier to diffuse when neglecting the interaction force, thus a lower viscosity will be.

  16. Nanostructure of Er3+ doped silicates.

    Science.gov (United States)

    Yao, Nan; Hou, Kirk; Haines, Christopher D; Etessami, Nathan; Ranganathan, Varadh; Halpern, Susan B; Kear, Bernard H; Klein, Lisa C; Sigel, George H

    2005-06-01

    We demonstrate nanostructural evolution resulting in highly increased photoluminescence in silicates doped with Er3+ ions. High-resolution transmission electron microscopy (HRTEM) imaging, nano-energy dispersed X-ray (NEDX) spectroscopy, X-ray diffraction (XRD) and photoluminescence analysis confirm the local composition and structure changes of the Er3+ ions upon thermal annealing. We studied two types of amorphous nanopowder: the first is of the composition SiO2/18Al2O3/2Er2O3 (SAE), synthesized by combustion flame-chemical vapor condensation, and the second is with a composition of SiO2/8Y2O3/2Er2O3 (SYE), synthesized by sol-gel synthesis (composition in mol%). Electron diffraction and HRTEM imaging clearly show the formation of nanocrystallites with an average diameter of approximately 8 nm in SAE samples annealed at 1000 degrees C and SYE samples annealed at 1200 degrees C. The volume fraction of the nanocrystalline phase increased with each heat treatment, eventually leading to complete devitrification at 1400 degrees C. Further XRD and NEDX analysis indicates that the nanocrystalline phase has the pyrochlore structure with the formula Er(x)Al(2-x)Si2O7 or Er(x)Y(2-x)Si2O7 and a surrounding silica matrix.

  17. Silicate Urolithiasis during Long-Term Treatment with Zonisamide

    Directory of Open Access Journals (Sweden)

    Satoru Taguchi

    2013-01-01

    Full Text Available Silicate urinary calculi are rare in humans, with an incidence of 0.2% of all urinary calculi. Most cases were related to excess ingestion of silicate, typically by taking magnesium trisilicate as an antacid for peptic ulcers over a long period of time; however, there also existed unrelated cases, whose mechanism of development remains unclear. On the other hand, zonisamide, a newer antiepileptic drug, is one of the important causing agents of iatrogenic urinary stones in patients with epilepsy. The supposed mechanism is that zonisamide induces urine alkalinization and then promotes crystallization of urine components such as calcium phosphate by inhibition of carbonate dehydratase in renal tubular epithelial cells. Here, we report a case of silicate urolithiasis during long-term treatment with zonisamide without magnesium trisilicate intake and discuss the etiology of the disease by examining the silicate concentration in his urine.

  18. Properties of sodium silicate bonded sand hardened by microwave heating

    Institute of Scientific and Technical Information of China (English)

    Wang Jina; Fan Zitian; Zan Xiaolei; Pan Di

    2009-01-01

    The sodium silicate bonded sand hardened by microwave heating has many advantages,such as low sodium silicate adding quantity,fast hardening speed,high room temperature strength,good collapsibility and certain surface stability. However,it has big moisture absorbability in the air,which would lead to the compression strength and the surface stability of the sand molds being sharply reduced. In this study,the moisture absorbability of the sodium silicate bonded sand hardened by microwave heating in different humidity conditions and the effect factors were investigated. Meanwhile,the reasons for the big moisture absorbability of the sand were analyzed.Some measures to overcome the problems of high moisture absorbability,bad surface stability and sharply reducing strength in the air were discussed. The results of this study establish the foundation of green and clean foundry technology based on the microwave heating hardening sodium silicate sand process.

  19. Polymer/layered silicates nanocomposites for barrier technology

    CSIR Research Space (South Africa)

    Labuschagne, Philip W

    2012-02-01

    Full Text Available -1 Intelligent Nanomaterials: Processes, Properties, and Applications February 2012/Chapter 13 Polymer/layered silicates nanocomposites for barrier technology Labuschagne, PW, Moolman, S and Maity, A. Corresponding author: PLabusch...

  20. Characterization of iron-phosphate-silicate chemical garden structures.

    Science.gov (United States)

    Barge, Laura M; Doloboff, Ivria J; White, Lauren M; Stucky, Galen D; Russell, Michael J; Kanik, Isik

    2012-02-28

    Chemical gardens form when ferrous chloride hydrate seed crystals are added or concentrated solutions are injected into solutions of sodium silicate and potassium phosphate. Various precipitation morphologies are observed depending on silicate and phosphate concentrations, including hollow plumes, bulbs, and tubes. The growth of precipitates is controlled by the internal osmotic pressure, fluid buoyancy, and membrane strength. Additionally, rapid bubble-led growth is observed when silicate concentrations are high. ESEM/EDX analysis confirms compositional gradients within the membranes, and voltage measurements across the membranes during growth show a final potential of around 150-200 mV, indicating that electrochemical gradients are maintained across the membranes as growth proceeds. The characterization of chemical gardens formed with iron, silicate, and phosphate, three important components of an early earth prebiotic hydrothermal system, can help us understand the properties of analogous structures that likely formed at submarine alkaline hydrothermal vents in the Hadean-structures offering themselves as the hatchery of life.

  1. The crystalline fraction of interstellar silicates in starburst galaxies

    CERN Document Server

    Kemper, F; Woods, Paul M

    2010-01-01

    We present a model using the evolution of the stellar population in a starburst galaxy to predict the crystallinity of the silicates in the interstellar medium of this galaxy. We take into account dust production in stellar ejecta, and amorphisation and destruction in the interstellar medium and find that a detectable amount of crystalline silicates may be formed, particularly at high star formation rates, and in case supernovae are efficient dust producers. We discuss the effect of dust destruction and amorphisation by supernovae, and the effect of a low dust-production efficiency by supernovae, and find that when taking this into account, crystallinity in the interstellar medium becomes hard to detect. Levels of 6.5-13% crystallinity in the interstellar medium of starburst galaxies have been observed and thus we conclude that not all these crystalline silicates can be of stellar origin, and an additional source of crystalline silicates associated with the Active Galactic Nucleus must be present.

  2. Spinning dust emission from ultrasmall silicates: emissivity and polarization spectrum

    CERN Document Server

    Hoang, Thiem; Lan, Nguyen Quynh

    2016-01-01

    Anomalous microwave emission (AME) is an important Galactic foreground of Cosmic Microwave Background (CMB) radiation. It is believed that the AME arises from rotational emission by spinning polycyclic aromatic hydrocarbons (PAHs) in the interstellar medium (ISM). In this paper, we assume that a population of ultrasmall silicate grains may exist in the ISM, and quantify rotational emissivity from these tiny particles and its polarization spectrum. We found that spinning silicate nanoparticles can produce strong rotational emission when those small grains follow a log-normal size distribution. The polarization fraction of spinning dust emission from tiny silicates increases with decreasing the dipole moment per atom ($\\beta$) and can reach $P\\sim 20\\%$ for $\\beta\\sim 0.1$D at grain temperature of 60 K. We identify a parameter space $(\\beta,Y_{Si})$ for silicate nanoparticles in which its rotational emission can adequately reproduce both the observed AME and the polarization of the AME, without violating the ob...

  3. In Vitro Susceptibility of Methicillin-Resistant Staphylococcus aureus and Methicillin-Susceptible Staphylococcus aureus to a New Antimicrobial, Copper Silicate▿

    OpenAIRE

    2007-01-01

    The soluble copper silicate (CS) MIC of 100 strains of methicillin-resistant Staphylococcus aureus and 100 strains of methicillin-susceptible S. aureus (MSSA) was 175 mg Cu/liter. Bactericidal and postantibiotic effects (≥1 h) were seen at 2× MIC and 4× MIC. The frequency of mutation was

  4. Fabricating Copper Nanotubes by Electrodeposition

    Science.gov (United States)

    Yang, E. H.; Ramsey, Christopher; Bae, Youngsam; Choi, Daniel

    2009-01-01

    Copper tubes having diameters between about 100 and about 200 nm have been fabricated by electrodeposition of copper into the pores of alumina nanopore membranes. Copper nanotubes are under consideration as alternatives to copper nanorods and nanowires for applications involving thermal and/or electrical contacts, wherein the greater specific areas of nanotubes could afford lower effective thermal and/or electrical resistivities. Heretofore, copper nanorods and nanowires have been fabricated by a combination of electrodeposition and a conventional expensive lithographic process. The present electrodeposition-based process for fabricating copper nanotubes costs less and enables production of copper nanotubes at greater rate.

  5. [Copper and the human body].

    Science.gov (United States)

    Krízek, M; Senft, V; Motán, J

    1997-11-19

    Copper is one of the essential trace elements. It is part of a number of enzymes. Deficiency of the element is manifested by impaired haematopoesis, bone metabolism, disorders of the digestive, cardiovascular and nervous system. Deficiency occurs in particular in patients suffering from malnutrition, malabsorption, great copper losses during administration of penicillamine. Sporadically copper intoxications are described (suicidal intentions or accidental ingestion of beverages with a high copper content). Acute exposure to copper containing dust is manifested by metal fume fever. Copper salts can produce local inflammations. Wilson's disease is associated with inborn impaired copper metabolism. In dialyzed patients possible contaminations of the dialyzate with copper must be foreseen as well as the possible release of copper from some dialyzation membranes. With the increasing amount of copper in the environment it is essential to monitor the contamination of the environment.

  6. Uptake of iodide by a mixture of metallic copper and cupric compounds

    Energy Technology Data Exchange (ETDEWEB)

    Lefevre, G.; Alnot, M.; Ehrhardt, J.J.; Bessiere, J. [Univ. Henri Poincare Nancy 1, Villers les Nancy (France). Lab. de Chimie Physique pour l`Environnement

    1999-05-15

    Environmental contaminants harmful to the health of present and future generations involve nuclear fission products as iodine radioisotopes. {sup 129}I is potentially one of the more mobile products because of its long half-life and its tendency to go into solution as an anion that is not retarded with silicate minerals. Ability of copper/cupric compound mixtures to remove iodide from solution was investigated to predict sorption of radioactive iodine in the environment and to assess their use in a nuclear reprocessing method. Thermodynamic calculations were performed to study the stability of such mixtures in solution and to obtain equilibrium constants of Cu(0)/Cu(II)/I{sup {minus}} and Cu(0)/Cu(II)/Cl{sup {minus}} systems. Both calculations and experimental results showed that a Cu(0)/Cu{sub 3}(OH){sub 2}(CO{sub 3}){sub 2} (azurite) mixture selectively uptakes iodide ions (initial concentrations: 10{sup {minus}2} and 10{sup {minus}1} M) in the presence of 10{sup {minus}1} M chloride ions. Reaction of iodide with copper powder and azurite crystal or copper plate and azurite powder have also been investigated, leading to precipitation of CuI onto massive copper phase. The different solids were separately analyzed by XPS and MEB-EDX, giving some insight in the uptake mechanism. It is proposed that soluble copper released by the cupric compound is reduced at the surface of metallic copper, leading to a preferential precipitation of CuI on copper surface.

  7. The copper recovery from cupric oxide catalysts by plasma reduction process

    Energy Technology Data Exchange (ETDEWEB)

    Imris, I.; Klenovcanova, A. [Technical Univ. of Kosice, Kosice (Slovakia). Dept. of Power Engineering

    2007-07-01

    A plasma reduction process was used to recover copper from cupric oxide catalysts. Two types of plasma reduction smelting tests were conducted to verify the thermodynamic calculations. The plasma reactor consisted of a cylindrical steel shell lined with a castable alumina and a graphite crucible. Cupric oxide catalyst ESM 461 was mixed with stoichiometric amounts of carbon reductant and a 10 per cent addition of calcium oxide flux. Results of the experimental tests and the thermodynamic analysis showed that the copper can be extracted from cupric oxide using the plasma reduction process. Copper recovery was limited by physico-chemical copper losses. Copper oxide solubility was relatively high, so that copper recovery was low in their first series of plasma tests. The addition of calcium oxide flux improved copper recovery rates when dicalcium silicate was formed in the slag. The offgas samples indicated that concentrations of carbon monoxide (CO) in the gas phase was very high. It was concluded that the process is both commercially feasible and does not produce liquid or solid wastes. 7 refs., 2 tabs., 4 figs.

  8. Generation of porphyry copper deposits by gas-brine reaction in volcanic arcs

    Science.gov (United States)

    Blundy, Jon; Mavrogenes, John; Tattitch, Brian; Sparks, Steve; Gilmer, Amy

    2014-05-01

    Porphyry copper deposits (PCDs) are characterised by a close spatial and temporal association with small, hypabyssal intrusions of silicic magmas in volcanic arcs. PCD formation requires elevated chlorine and water to concentrate copper in magmatic hypersaline liquids (or brines), and elevated sulphur to precipitate copper-rich sulphides. These twin requirements are hard to reconcile with experimental and petrological evidence that voluminous chlorine-rich, hydrous silicic magmas, of the variety favourable to copper enrichment, lack sufficient sulphur to precipitate directly the requisite quantities of sulphides. These features are, however, consistent with observations of active volcanic arcs whereby PCDs can be viewed as roots of dome volcanoes above shallow reservoirs where silicic magmas accumulate over long time spans. During protracted periods of dormancy metal-enriched dense brines accumulate in and above the silicic reservoir through slow, low-pressure degassing. Meanwhile cogenetic volatile-rich mafic magmas and their exsolved, sulphur and CO2-rich fluids accumulate in deeper reservoirs. Periodic destabilisation of these reservoirs leads to short-lived bursts of volcanism liberating sulphurous gases, which react with the shallow-stored brines to form copper-rich sulphides and acidic vapours. We test this hypothesis with a novel set of 'porphyry in a capsule' experiments designed to simulate low-pressure (1-2 kbar) interaction of basalt-derived, sulphur-rich gases with brine-saturated, copper-bearing, but sulphur-free, granite. Experiments were run at 720-850 ° C in cold-seal apparatus with basaltic andesite, loaded with H2O and S, situated below dacite, loaded with H2O, Cl and Cu. At run conditions both compositions are substantially degassed and crystallized. S-rich gas from the basaltic andesite ascends to react with Cu-rich brines exsolved from the dacite, Our experiments reveal the direct precipitation of copper-sulphide minerals, in vugs and veins

  9. Determination of reactivity rates of silicate particle-size fractions

    OpenAIRE

    Angélica Cristina Fernandes Deus; Leonardo Theodoro Büll; Juliano Corulli Corrêa; Roberto Lyra Villas Boas

    2014-01-01

    The efficiency of sources used for soil acidity correction depends on reactivity rate (RR) and neutralization power (NP), indicated by effective calcium carbonate (ECC). Few studies establish relative efficiency of reactivity (RER) for silicate particle-size fractions, therefore, the RER applied for lime are used. This study aimed to evaluate the reactivity of silicate materials affected by particle size throughout incubation periods in comparison to lime, and to calculate the RER for silicat...

  10. Geochemistry of yukon and copper river tributaries, Alaska

    Science.gov (United States)

    Carney, M.; Ellis, A.; Bullen, T.; Langman, J.

    2009-01-01

    Alaska is already beginning to be affected by changes in global climate which make it a good location to study the feedback effects between climate, the water cycle and the carbon cycle. Using river dissolved elements and Sr isotopes we examine changes and/or differences in chemical weathering between watersheds in predominantly permafrost areas and glacial watersheds. Tributaries of the Tanana, Yukon, Nenana and Copper rivers were sampled during the early snow melt in late May and the late permafrost/glacial melt period in September of 2007. Waters are predominantly CaHCO3-/SO4 which is typical of glaciated terrains. 87Sr/86Sr isotopes indicate three potential end-members, young basalts, radiogenic silicates and marine carbonates. The results are consistent with weathering observed in glaciated regions with trace calcites and salts dominating the dissolved load; however we have evidence for silicate weathering. Results also indicate that permafrost watersheds experience more progressive silicate weathering than glacial watersheds. ??2009 ASCE.

  11. Targeting copper in cancer therapy: 'Copper That Cancer'.

    Science.gov (United States)

    Denoyer, Delphine; Masaldan, Shashank; La Fontaine, Sharon; Cater, Michael A

    2015-11-01

    Copper is an essential micronutrient involved in fundamental life processes that are conserved throughout all forms of life. The ability of copper to catalyze oxidation-reduction (redox) reactions, which can inadvertently lead to the production of reactive oxygen species (ROS), necessitates the tight homeostatic regulation of copper within the body. Many cancer types exhibit increased intratumoral copper and/or altered systemic copper distribution. The realization that copper serves as a limiting factor for multiple aspects of tumor progression, including growth, angiogenesis and metastasis, has prompted the development of copper-specific chelators as therapies to inhibit these processes. Another therapeutic approach utilizes specific ionophores that deliver copper to cells to increase intracellular copper levels. The therapeutic window between normal and cancerous cells when intracellular copper is forcibly increased, is the premise for the development of copper-ionophores endowed with anticancer properties. Also under investigation is the use of copper to replace platinum in coordination complexes currently used as mainstream chemotherapies. In comparison to platinum-based drugs, these promising copper coordination complexes may be more potent anticancer agents, with reduced toxicity toward normal cells and they may potentially circumvent the chemoresistance associated with recurrent platinum treatment. In addition, cancerous cells can adapt their copper homeostatic mechanisms to acquire resistance to conventional platinum-based drugs and certain copper coordination complexes can re-sensitize cancer cells to these drugs. This review will outline the biological importance of copper and copper homeostasis in mammalian cells, followed by a discussion of our current understanding of copper dysregulation in cancer, and the recent therapeutic advances using copper coordination complexes as anticancer agents.

  12. Friction and Wear Behaviors of Nano-Silicates in Water

    Institute of Scientific and Technical Information of China (English)

    Chen Boshui; Lou Fang; Fang Jianhua; Wang Jiu; Li Jia

    2009-01-01

    Nano-metric magnesium silicate and zinc silicate with particle size of about 50--70nm were prepared in water by the method of chemical deposition. The antiwear and friction reducing abilities of the nano-silicates, as well as their compos-ites with oleie acid tri-ethanolamine (OATEA), were evaluated on a four-ball friction tester. The topographies and tribochemical features of the worn surfaces were analyzed by scanning electron microscope (SEM) and X-ray photoelectron spectroscope (XPS). Results show that nano-silicates alone provide poor antiwear and friction reducing abilities in water, but exhibits excellent synergism with OATEA in reducing friction and wear. The synergism in reducing friction and wear between naao-silicates and OATEA does exist almost regardless of particle sizes and species, and may be attributed, on one hand, to the formation of an adsorption film of OATEA, and, on the other hand, to the formation oftdbochemical species of silicon dioxide and iron oxides on the friction surfaces. Tribo-reactions and tribo-adsorptions of nano-silicates and OATEA would produce hereby an effective composite boondary lubrication film, which could efficiently enhance the anti-wear and friction-reducing abilities of water.

  13. High Pressure/Temperature Metal Silicate Partitioning of Tungsten

    Science.gov (United States)

    Shofner, G. A.; Danielson, L.; Righter, K.; Campbell, A. J.

    2010-01-01

    The behavior of chemical elements during metal/silicate segregation and their resulting distribution in Earth's mantle and core provide insight into core formation processes. Experimental determination of partition coefficients allows calculations of element distributions that can be compared to accepted values of element abundances in the silicate (mantle) and metallic (core) portions of the Earth. Tungsten (W) is a moderately siderophile element and thus preferentially partitions into metal versus silicate under many planetary conditions. The partitioning behavior has been shown to vary with temperature, silicate composition, oxygen fugacity, and pressure. Most of the previous work on W partitioning has been conducted at 1-bar conditions or at relatively low pressures, i.e. <10 GPa, and in two cases at or near 20 GPa. According to those data, the stronger influences on the distribution coefficient of W are temperature, composition, and oxygen fugacity with a relatively slight influence in pressure. Predictions based on extrapolation of existing data and parameterizations suggest an increased pressured dependence on metal/ silicate partitioning of W at higher pressures 5. However, the dependence on pressure is not as well constrained as T, fO2, and silicate composition. This poses a problem because proposed equilibration pressures for core formation range from 27 to 50 GPa, falling well outside the experimental range, therefore requiring exptrapolation of a parametereized model. Higher pressure data are needed to improve our understanding of W partitioning at these more extreme conditions.

  14. Potassium silicate and calcium silicate on the resistance of soybean to Phakopsora pachyrhizi infection

    Directory of Open Access Journals (Sweden)

    Maria Fernanda Cruz

    2013-01-01

    Full Text Available The control of Asian Soybean Rust (ASR, caused by Phakopsora pachyrhizi, has been difficult due to the aggressiveness of the pathogen and the lack of resistant cultivars. The objective of this study was to evaluate the effects of spray of potassium silicate (PS and soil amendment with calcium silicate (CS on soybean resistance to ASR. The PS solution was sprayed to leaves 24 hours prior to fungal inoculation while CS was amended to the soil at thirty-five days before sowing. The infection process of P. pachyrhizi was investigated by scanning electron microscopy. The uredia on leaves of plants sprayed with PS were smaller and more compact than those observed on the leaves of plants grown in soil amended with CS or in soil non-amended with CS (control treatment. On leaves of plants from the control treatment, uredia produced many urediniospores at 9 days after inoculation, and the ASR severity was 15, 8 and 9%, respectively, for plants from control, PS and CS treatments. In conclusion, the spray of PS contributed to reduce the number of uredia per cm² of leaf area and both PS spray and CS resulted in lower ASR symptoms.

  15. Partitioning coefficients between olivine and silicate melts

    Science.gov (United States)

    Bédard, J. H.

    2005-08-01

    Variation of Nernst partition coefficients ( D) between olivine and silicate melts cannot be neglected when modeling partial melting and fractional crystallization. Published natural and experimental olivine/liquidD data were examined for covariation with pressure, temperature, olivine forsterite content, and melt SiO 2, H 2O, MgO and MgO/MgO + FeO total. Values of olivine/liquidD generally increase with decreasing temperature and melt MgO content, and with increasing melt SiO 2 content, but generally show poor correlations with other variables. Multi-element olivine/liquidD profiles calculated from regressions of D REE-Sc-Y vs. melt MgO content are compared to results of the Lattice Strain Model to link melt MgO and: D0 (the strain compensated partition coefficient), EM3+ (Young's Modulus), and r0 (the size of the M site). Ln D0 varies linearly with Ln MgO in the melt; EM3+ varies linearly with melt MgO, with a dog-leg at ca. 1.5% MgO; and r0 remains constant at 0.807 Å. These equations are then used to calculate olivine/liquidD for these elements using the Lattice Strain Model. These empirical parameterizations of olivine/liquidD variations yield results comparable to experimental or natural partitioning data, and can easily be integrated into existing trace element modeling algorithms. The olivine/liquidD data suggest that basaltic melts in equilibrium with pure olivine may acquire small negative Ta-Hf-Zr-Ti anomalies, but that negative Nb anomalies are unlikely to develop. Misfits between results of the Lattice Strain Model and most light rare earth and large ion lithophile partitioning data suggest that kinetic effects may limit the lower value of D for extremely incompatible elements in natural situations characterized by high cooling/crystallization rates.

  16. LEP copper accelerating cavities

    CERN Multimedia

    Laurent Guiraud

    1999-01-01

    These copper cavities were used to generate the radio frequency electric field that was used to accelerate electrons and positrons around the 27-km Large Electron-Positron (LEP) collider at CERN, which ran from 1989 to 2000. The copper cavities were gradually replaced from 1996 with new superconducting cavities allowing the collision energy to rise from 90 GeV to 200 GeV by mid-1999.

  17. Copper wire bonding

    CERN Document Server

    Chauhan, Preeti S; Zhong, ZhaoWei; Pecht, Michael G

    2014-01-01

    This critical volume provides an in-depth presentation of copper wire bonding technologies, processes and equipment, along with the economic benefits and risks.  Due to the increasing cost of materials used to make electronic components, the electronics industry has been rapidly moving from high cost gold to significantly lower cost copper as a wire bonding material.  However, copper wire bonding has several process and reliability concerns due to its material properties.  Copper Wire Bonding book lays out the challenges involved in replacing gold with copper as a wire bond material, and includes the bonding process changes—bond force, electric flame off, current and ultrasonic energy optimization, and bonding tools and equipment changes for first and second bond formation.  In addition, the bond–pad metallurgies and the use of bare and palladium-coated copper wires on aluminum are presented, and gold, nickel and palladium surface finishes are discussed.  The book also discusses best practices and re...

  18. COMPARISON OF SOL-GEL SILICATE COATINGS ON Ti SUBSTRATE

    Directory of Open Access Journals (Sweden)

    DIANA HORKAVCOVÁ

    2012-12-01

    Full Text Available The objective of the submitted work was to prepare and to characterize two types of silicate coatings prepared by the sol-gel method using the dip-coating technique on a titanium substrate. Efforts have been made to use mechanical properties of bio-inert titanium and bioactive properties of a silicate layer enriched with an admixture of compounds identified below. The first group consisted of silicate coatings containing silver, brushite and monetite. The other group of silicate coatings contained calcium nitrate and triethyl phosphate. Mechanically and chemically treated titanium substrates were dipped into sols and dried and fired. Silicate coatings from the first group were also chemically treated in 10 mol.l-1 solution of sodium hydroxide. All coatings were measured to determine their adhesive and bioactive properties and furthermore the antibacterial properties were tested in the case of first group. Surfaces of the coated substrates were investigated after the firing and after the individual tests with optical and electron microscopy and X-ray microdiffraction. A tape test demonstrated excellent adhesive property of all coatings to the substrate, classified with degree 5. A static in vitro test demonstrated bioactivity of nearly all the coatings. The basic silicate coating from the first group and one type of coating from the second group were identified as inert. Antibacterial properties of silicate coatings containing silver showed to be different when tested against Escherichia coli bacteria. A complete inhibition of the growth of bacteria under our experimental conditions was observed for the coating containing silver and monetite and a partial inhibition of the growth of bacteria for coatings containing silver and silver in combination with brushite.

  19. Standard Specification for Copper-Aluminum-Silicon-Cobalt Alloy, Copper-Nickel-Silicon-Magnesium Alloy, Copper-Nickel-Silicon Alloy, Copper-Nickel-Aluminum-Magnesium Alloy, and Copper-Nickel-Tin Alloy Sheet and Strip

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2015-01-01

    Standard Specification for Copper-Aluminum-Silicon-Cobalt Alloy, Copper-Nickel-Silicon-Magnesium Alloy, Copper-Nickel-Silicon Alloy, Copper-Nickel-Aluminum-Magnesium Alloy, and Copper-Nickel-Tin Alloy Sheet and Strip

  20. Re-Os Dating of the Pulang Porphyry Copper Deposit in Zhongdian, NW Yunnan, and Its Geological Significance

    Institute of Scientific and Technical Information of China (English)

    ZENG Pusheng; HOU Zengqian; WANG Haiping; QU Wenjun; MENG Yifeng; YANG Zhusen; LI Wenchang

    2004-01-01

    The Pulang porphyry copper deposit is located in the Zhongdian island arc belt, NW Yunnan, in the central part of the Sanjiang area, SW China, belonging to the southern segment of the Yidun island arc belt on the western margin of the Yangtze Platform. In the Yidun island arc, there occur well-known "Gacun-style" massive sulfide deposits in the northern segment and plenty of porphyry copper deposits in the southern segment, of which the Pulang porphyry copper deposit is one of the representatives. Like the Yulong porphyry copper deposit, this porphyry copper deposit is also one of the most important porphyry copper deposits in the eastern Qinghai-Tibet Plateau. But it is different from other porphyry copper deposits in the eastern Qinghai-Tibet Plateau (e.g. those in the Gangdise porphyry copper belt and Yulong porphyry copper belt) in that it formed in the Indosinian period, while others in the Himalayan period. Because of its particularity among the porphyry copper deposits of China, this porphyry copper deposit is of great significance for the study of the basic geology and the evaluation and prediction of mineral resources in the Zhongdian island arc belt.However, no accurate chronological data are available for determining the timing of mineralization of the porphyry copper deposit. By field observation in the study area and Re-Os dating of molybdenite and K-Ar dating of hydrothermal minerals and whole rock from the typical geological bodies, the timing of mineralization of the porphyry copper deposit has systematically been determined for the first time. The K-Ar age for the hydrothermal mineralization of biotite-quartz monzonitic porphyry that has undergone patassic silicate (biotite and K-feldspar) alteration ranges from 235.4±2.4 to 221.5±2.0 Ma and the Re-Os age for molybdenite in the quartz-molybdenite stage is ~213±3.8 Ma. These data are very close to each other, suggesting that the ore-forming processes of the Pulang porphyry copper deposit was

  1. Silicic Arc Magmas And Silicic Slab Melts: The Melt-Rock Reaction Link

    Science.gov (United States)

    Straub, S. M.; Gomez-Tuena, A.; Bolge, L. L.; Espinasa-Perena, R.; Bindeman, I. N.; Stuart, F. M.; Zellmer, G. F.

    2013-12-01

    While a genetic link between silicic arc magmas and silicic melts from the subducted slab has long been proposed, this hypothesis is commonly refuted because most arc magmas lack a 'garnet-signature' which such slab melts must have. A comprehensive geochemical study of high-Mg# arc magmas from the Quaternary central Mexican Volcanic Belt (MVB), however, shows that this conflict can be reconciled if melt-rock reaction processes in the mantle wedge were essential to arc magma formation. In the central MVB, monogenetic and composite volcanoes erupt high-Mg# basalts to andesites with highly variable trace element patterns. These magmas contain high-Ni olivines (olivine Ni higher than permissible for olivines in partial peridotite melts) with high 3He/4He = 7-8 Ra that provide strong evidence for silicic slab components that infiltrate the subarc mantle to produce olivine-free segregations of 'reaction pyroxenite' in the sources of individual volcanoes. Melting of silica-excess and silica-deficient reaction pyroxenites can then produce high-Mg# basaltic and dacitic primary melts that mix during ascent through mantle and crust to form high-Mg# andesites. Mass balance requires that reaction pyroxenites contain at least >15-18 wt%, and likely more, of slab component. However, because the HREE of the slab component are efficiently retained in the eclogitic slab, elements Ho to Lu in partial melts from reaction pyroxenites remain controlled by the mantle and maintain MORB-normalized Ho/Lun ˜1.15 close to unity. In contrast, the MREE to LREE and fluid mobile LILE of the arc magmas are either controlled, or strongly influenced, by slab-contributions. The origin from hybrid sources also shows in the major elements that are blends of mantle-derived elements (Mg, Ca, Mn, Fe, Ti) and elements augmented by slab contributions (Si, Na, K, P, and possibly Al). Moreover, strong correlations between bulk rock SiO2, 87Sr/86Sr and δ18O (olivines) can be interpreted as mixtures of subarc

  2. Leaching for recovery of copper from municipal solid waste incineration fly ash: influence of ash properties and metal speciation.

    Science.gov (United States)

    Lassesson, Henric; Fedje, Karin Karlfeldt; Steenari, Britt-Marie

    2014-08-01

    Recovery of metals occurring in significant amounts in municipal solid waste incineration fly ash, such as copper, could offer several advantages: a decreased amount of potentially mobile metal compounds going to landfill, saving of natural resources and a monetary value. A combination of leaching and solvent extraction may constitute a feasible recovery path for metals from municipal solid waste incineration fly ash. However, it has been shown that the initial dissolution and leaching is a limiting step in such a recovery process. The work described in this article was focused on elucidating physical and chemical differences between two ash samples with the aim of explaining the differences in copper release from these samples in two leaching methods. The results showed that the chemical speciation is an important factor affecting the release of copper. The occurrence of copper as phosphate or silicate will hinder leaching, while sulphate and chloride will facilitate leaching.

  3. Heterogeneous nucleation of protein crystals on fluorinated layered silicate.

    Directory of Open Access Journals (Sweden)

    Keita Ino

    Full Text Available Here, we describe an improved system for protein crystallization based on heterogeneous nucleation using fluorinated layered silicate. In addition, we also investigated the mechanism of nucleation on the silicate surface. Crystallization of lysozyme using silicates with different chemical compositions indicated that fluorosilicates promoted nucleation whereas the silicates without fluorine did not. The use of synthesized saponites for lysozyme crystallization confirmed that the substitution of hydroxyl groups contained in the lamellae structure for fluorine atoms is responsible for the nucleation-inducing property of the nucleant. Crystallization of twelve proteins with a wide range of pI values revealed that the nucleation promoting effect of the saponites tended to increase with increased substitution rate. Furthermore, the saponite with the highest fluorine content promoted nucleation in all the test proteins regardless of their overall net charge. Adsorption experiments of proteins on the saponites confirmed that the density of adsorbed molecules increased according to the substitution rate, thereby explaining the heterogeneous nucleation on the silicate surface.

  4. Silicate Dust in Evolved Protoplanetary Disks: Growth, Sedimentation, and Accretion

    CERN Document Server

    Sicilia-Aguilar, Aurora; Watson, Dan; Bohac, Chris; Henning, Thomas; Bouwman, Jeroen; 10.1086/512121

    2009-01-01

    We present the Spitzer IRS spectra for 33 young stars in Tr 37 and NGC 7160. The sample includes the high- and intermediate-mass stars with MIPS 24 microns excess, the only known active accretor in the 12 Myr-old cluster NGC 7160, and 19 low-mass stars with disks in the 4 Myr-old cluster Tr 37. We examine the 10 microns silicate feature, present in the whole sample of low-mass star and in 3 of the high- and intermediate-mass targets, and we find that PAH emission is detectable only in the Herbig Be star. We analyze the composition and size of the warm photospheric silicate grains by fitting the 10 microns silicate feature, and study the possible correlations between the silicate characteristics and the stellar and disk properties (age, SED slope, accretion rate, spectral type). We find indications of dust settling with age and of the effect of turbulent enrichment of the disk atmosphere with large grains. Crystalline grains are only small contributors to the total silicate mass in all disks, and do not seem t...

  5. Copper and Copper Proteins in Parkinson’s Disease

    OpenAIRE

    Sergio Montes; Susana Rivera-Mancia; Araceli Diaz-Ruiz; Luis Tristan-Lopez; Camilo Rios

    2014-01-01

    Copper is a transition metal that has been linked to pathological and beneficial effects in neurodegenerative diseases. In Parkinson's disease, free copper is related to increased oxidative stress, alpha-synuclein oligomerization, and Lewy body formation. Decreased copper along with increased iron has been found in substantia nigra and caudate nucleus of Parkinson's disease patients. Copper influences iron content in the brain through ferroxidase ceruloplasmin activity; therefore decreased pr...

  6. Jiangxi Copper Plans to Increase its Refined Copper Output

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>According to news published on March 30th, China’s largest copper producer--Jiangxi Copper alleged in its 2010 Financial Report Statement that it plans to improve its output of refined copper by 4.4% in 2011, to increase from 900,000 tonnes last year to 940,000 tons.

  7. Determination of silver, bismuth, cadmium, copper, lead, and zinc in geologic materials by atomic absorption spectrometry with tricaprylylmethylammonium chloride

    Science.gov (United States)

    Viets, J.G.

    1978-01-01

    Interferences commonly encountered in the determination of silver, bismuth, cadmium, copper, lead, and zinc at crustal abundance levels are effectively eliminated using a rapid, sensitive, organic extraction technique. A potassium chlorate-hydrochloric acid digestion solubilizes the metals not tightly bound in the silicate lattice of rocks, soils, and stream sediments. The six metals are selectively extracted into a 10% Aliquat 336-MIBK organic phase in the presence of ascorbic acid and potassium iodide. Metals in the organic extract are determined by flame atomic absorption spectrometry to the 0.02-ppm level for silver, cadmium, copper, and zinc and to the 0.2-ppm level for bismuth and lead with a maximum relative standard deviation of 18.8% for known reference samples. An additional hydrofluoric acid digestion may be used to determine metals substituted in the silicate lattice.

  8. DFT calculations of EPR parameters for copper(II)-exchanged zeolites using cluster models.

    Science.gov (United States)

    Ames, William M; Larsen, Sarah C

    2010-01-14

    The coordination environment of Cu(II) in hydrated copper-exchanged zeolites was explored through the use of density functional theory (DFT) calculations of EPR parameters. Extensive experimental EPR data are available in the literature for hydrated copper-exchanged zeolites. The copper complex in hydrated copper-exchanged zeolites was previously proposed to be [Cu(H(2)O)(5)OH](+) based on empirical trends in tetragonal model complex EPR data. In this study, calculated EPR parameters for the previously proposed copper complex, [Cu(H(2)O)(5)OH](+), were compared to model complexes in which Cu(II) was coordinated to small silicate or aluminosilicate clusters as a first approximation of the impact of the zeolitic environment on the copper complex. Interpretation of the results suggests that Cu(II) is coordinated or closely associated with framework oxygen atoms within the zeolite structure. Additionally, it is proposed that the EPR parameters are dependent on the Si/Al ratio of the parent zeolite.

  9. [Copper metabolism and genetic disorders].

    Science.gov (United States)

    Shimizu, Norikazu

    2016-07-01

    Copper is one of essential trace elements. Copper deficiency lead to growth and developmental failure and/or neurological dysfunction. However, excess copper is also problems for human life. There are two disorders of inborn error of copper metabolism, Menkes disease and Wilson disease. Menkes disease is an X linked recessive disorder with copper deficiency and Wilson disease is an autosomal recessive disorder with copper accumulation. These both disorders result from the defective functioning of copper transport P-type ATPase, ATP7A of Menkes disease and ATP7B of Wilson disease. In this paper, the author describes about copper metabolism of human, and clinical feature, diagnosis and treatment of Menkes disease and Wilson disease.

  10. Energetic Processing of Interstellar Silicate Grains by Cosmic Rays

    Energy Technology Data Exchange (ETDEWEB)

    Bringa, E M; Kucheyev, S O; Loeffler, M J; Baragiola, R A; Tielens, A G Q M; Dai, Z R; Graham, G; Bajt, S; Bradley, J; Dukes, C A; Felter, T E; Torres, D F; van Breugel, W

    2007-03-28

    While a significant fraction of silicate dust in stellar winds has a crystalline structure, in the interstellar medium nearly all of it is amorphous. One possible explanation for this observation is the amorphization of crystalline silicates by relatively 'low' energy, heavy ion cosmic rays. Here we present the results of multiple laboratory experiments showing that single-crystal synthetic forsterite (Mg{sub 2}SiO{sub 4}) amorphizes when irradiated by 10 MeV Xe{sup ++} ions at large enough fluences. Using modeling, we extrapolate these results to show that 0.1-5.0 GeV heavy ion cosmic rays can rapidly ({approx}70 Million yrs) amorphize crystalline silicate grains ejected by stars into the interstellar medium.

  11. Behaviour of Silicate Melts in Respect of Volume

    Institute of Scientific and Technical Information of China (English)

    张金民; 叶大年

    1989-01-01

    The volumes per oxygen of some silicate melts have been calculated and then compared with those of silicate glasses.It is suggested that the volume of a silicate melt can be divided into two parts.One is contri buted by the silicon-oxygen network and the other by the “oxides”.Variation patterns of VPOs suggest that the volume of the Si-O network generally remains unchanged and the expansion of the melt is caused mainly by the locat expansion of the “oxides”.It is further proposed that the radius of O2- shows little variation,in striking contrast to the radius of cations.The mechanism governing the expansion is discussed in detail.

  12. Functional substitution of coordination polyhedron in crystal structure of silicates

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    On the bases of the study of comparative crystal chemistry of silicates it has been concluded that the octahedra and square pyramids of Ti-O and Zr-O play functional role of tetrahedra of Si-O in the construction of crystal structures.Therefore,those silicates may be named titano- and zircono-silicates.Because of the functional similarity of coordination polyhedra,the structures of cristobalite and feldspar have been compared with those of perovskite and garnet,respectively.As a new concept,the functional replacement of tetrahedra by octahedra and/or pyramids is defined by the authors of this paper for favorable comparison of relative crystal structures.

  13. Structural chemistry of anhydrous sodium silicates - a review.

    Science.gov (United States)

    Kahlenberg, Volker

    2010-01-01

    Sodium silicates are of considerable importance for many fields of inorganic chemistry and applied mineralogy, being either raw materials for synthesis or already finished products. In addition to their industrial relevance they have also been studied intensively because of their interesting physico-chemical properties including high ion-exchange capacity and selectivity or two-dimensional sodium diffusion and conductivity. Furthermore, the structural chemistry of crystalline sodium silicates offers the crystallographer challenging tasks such as polytypism, polymorphism, temperature and/or pressure-dependent phase transitions, pseudo-symmetry, complex twinning phenomena as well as incommensurately modulated structures. Many of these structural problems have been solved only recently, although in some cases they have been known for several decades. This article will provide an overview on the structurally characterized sodium silicates and their fascinating crystallochemical characteristics.

  14. Effect of Minor Elements on Silicate Cement Clinker

    Institute of Scientific and Technical Information of China (English)

    HUANG Congyun; ZHANG Mingfei; ZHANG Meixiang; LONG Shizong; CHEN Yuankui; MA Baoguo

    2005-01-01

    The effect of rare-earth and HX addition agent on the burn-ability of silicate cement clinker was investigated by orthogonal experiment. The result shows, compared with blank sample, f- CaO of the samples added with rare-earth and HX agent drops by 84.95% , its 3d and 28d compressive strength enhances by 24.40%and 16.90%, respectively. It was discovered by means of X-ray diffraction and high temperature microscope analysis that sintering temperature of the sample added with rare-earth and HX addition agent is about 1320℃. At the same time, the burning temperature of tricalcium silicate desends and its crystal growth forming-rate increases.Tricalcium silicate content in burning clinker is higher and its crystal is larger.

  15. Evolution of trees and mycorrhizal fungi intensifies silicate mineral weathering

    Science.gov (United States)

    Quirk, Joe; Beerling, David J.; Banwart, Steve A.; Kakonyi, Gabriella; Romero-Gonzalez, Maria E.; Leake, Jonathan R.

    2012-01-01

    Forested ecosystems diversified more than 350 Ma to become major engines of continental silicate weathering, regulating the Earth's atmospheric carbon dioxide concentration by driving calcium export into ocean carbonates. Our field experiments with mature trees demonstrate intensification of this weathering engine as tree lineages diversified in concert with their symbiotic mycorrhizal fungi. Preferential hyphal colonization of the calcium silicate-bearing rock, basalt, progressively increased with advancement from arbuscular mycorrhizal (AM) to later, independently evolved ectomycorrhizal (EM) fungi, and from gymnosperm to angiosperm hosts with both fungal groups. This led to ‘trenching’ of silicate mineral surfaces by AM and EM fungi, with EM gymnosperms and angiosperms releasing calcium from basalt at twice the rate of AM gymnosperms. Our findings indicate mycorrhiza-driven weathering may have originated hundreds of millions of years earlier than previously recognized and subsequently intensified with the evolution of trees and mycorrhizas to affect the Earth's long-term CO2 and climate history. PMID:22859556

  16. Electric field-induced softening of alkali silicate glasses

    Energy Technology Data Exchange (ETDEWEB)

    McLaren, C.; Heffner, W.; Jain, H. [Department of Materials Science and Engineering, Lehigh University, Bethlehem, Pennsylvania 18015 (United States); Tessarollo, R.; Raj, R. [Department of Mechanical Engineering, University of Colorado at Boulder, Boulder, Colorado 80309 (United States)

    2015-11-02

    Motivated by the advantages of two-electrode flash sintering over normal sintering, we have investigated the effect of an external electric field on the viscosity of glass. The results show remarkable electric field-induced softening (EFIS), as application of DC field significantly lowers the softening temperature of glass. To establish the origin of EFIS, the effect is compared for single vs. mixed-alkali silicate glasses with fixed mole percentage of the alkali ions such that the mobility of alkali ions is greatly reduced while the basic network structure does not change much. The sodium silicate and lithium-sodium mixed alkali silicate glasses were tested mechanically in situ under compression in external electric field ranging from 0 to 250 V/cm in specially designed equipment. A comparison of data for different compositions indicates a complex mechanical response, which is observed as field-induced viscous flow due to a combination of Joule heating, electrolysis and dielectric breakdown.

  17. Calcined sodium silicate as solid base catalyst for biodiesel production

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Feng; Peng, Zhen-Gang; Dai, Jian-Ying; Xiu, Zhi-Long [Department of Bioscience and Biotechnology, School of Environmental and Biological Science and Technology, Dalian University of Technology, Dalian 116024 (China)

    2010-03-15

    This paper examined the use of calcined sodium silicate as a novel solid base catalyst in the transesterification of soybean oil with methanol. The calcined sodium silicate was characterized by DTA-TG, Hammett indicator method, XRD, SEM, BET, IR and FT-IR. It catalyzed the transesterification of soybean oil to biodiesel with a yield of almost 100% under the following conditions: sodium silicate of 3.0 wt.%, a molar ratio of methanol/oil of 7.5:1, reaction time of 60 min, reaction temperature of 60 C, and stirring rate of 250 rpm. The oil containing 4.0 wt.% water or 2.5 wt.% FFA could also be transesterified by using this catalyst. The catalyst can be reused for at least 5 cycles without loss of activity. (author)

  18. Electric field-induced softening of alkali silicate glasses

    Science.gov (United States)

    McLaren, C.; Heffner, W.; Tessarollo, R.; Raj, R.; Jain, H.

    2015-11-01

    Motivated by the advantages of two-electrode flash sintering over normal sintering, we have investigated the effect of an external electric field on the viscosity of glass. The results show remarkable electric field-induced softening (EFIS), as application of DC field significantly lowers the softening temperature of glass. To establish the origin of EFIS, the effect is compared for single vs. mixed-alkali silicate glasses with fixed mole percentage of the alkali ions such that the mobility of alkali ions is greatly reduced while the basic network structure does not change much. The sodium silicate and lithium-sodium mixed alkali silicate glasses were tested mechanically in situ under compression in external electric field ranging from 0 to 250 V/cm in specially designed equipment. A comparison of data for different compositions indicates a complex mechanical response, which is observed as field-induced viscous flow due to a combination of Joule heating, electrolysis and dielectric breakdown.

  19. Rubber curing chemistry governing the orientation of layered silicate

    Directory of Open Access Journals (Sweden)

    2007-11-01

    Full Text Available The effect of curing systems on the orientation and the dispersion of the layered silicates in acrylonitrile butadiene rubber nanocomposite is reported. Significant differences in X-ray diffraction pattern between peroxide curing and sulfur curing was observed. Intense X-ray scattering values in the XRD experiments from peroxide cured vulcanizates indicate an orientation of the layers in a preferred direction as evinced by transmission electron micrographs. However, sulfur cured vulcanizates show no preferential orientation of the silicate particles. Nevertheless, a closer inspection of transmission electron microscopy (TEM images of peroxide and sulfur cured samples shows exfoliated silicate layers in the acrylonitrile butadiene rubber (NBR matrix. It was revealed in the prevailing study that the use of an excess amount of stearic acid in the formulation of the sulfur curing package leads to almost exfoliated type X-ray scattering pattern.

  20. Nitrogen distribution between aqueous fluids and silicate melts

    Science.gov (United States)

    Li, Yuan; Huang, Ruifang; Wiedenbeck, Michael; Keppler, Hans

    2015-02-01

    The partitioning of nitrogen between hydrous fluids and haplogranitic, basaltic, or albitic melts was studied at 1-15 kbar, 800-1200 °C, and oxygen fugacities (fO2) ranging from the Fe-FeO buffer to 3log units above the Ni-NiO buffer. The nitrogen contents in quenched glasses were analyzed either by electron microprobe or by secondary ion mass spectrometry (SIMS), whereas the nitrogen contents in fluids were determined by mass balance. The results show that the nitrogen content in silicate melt increases with increasing nitrogen content in the coexisting fluid at given temperature, pressure, and fO2. Raman spectra of the silicate glasses suggest that nitrogen species change from molecular N2 in oxidized silicate melt to molecular ammonia (NH3) or the ammonium ion (NH4+) in reduced silicate melt, and the normalized Raman band intensities of the nitrogen species linearly correlate with the measured nitrogen content in silicate melt. Elevated nitrogen contents in silicate melts are observed at reduced conditions and are attributed to the dissolution of NH3/NH4+. Measured fluid/melt partition coefficients for nitrogen (DNfluid/ melt) range from 60 for reduced haplogranitic melts to about 10 000 for oxidized basaltic melts, with fO2 and to a lesser extent melt composition being the most important parameters controlling the partitioning of nitrogen. Pressure appears to have only a minor effect on DNfluid/ melt in the range of conditions studied. Our data imply that degassing of nitrogen from both mid-ocean ridge basalts and arc magmas is very efficient, and predicted nitrogen abundances in volcanic gases match well with observations. Our data also confirm that nitrogen degassing at present magma production rates is insufficient to accumulate the atmosphere. Most of the nitrogen in the atmosphere must have degassed very early in Earth's history and degassing was probably enhanced by the oxidation of the mantle.

  1. Potassium Silicate Foliar Fertilizer Grade from Geothermal Sludge and Pyrophyllite

    Directory of Open Access Journals (Sweden)

    Muljani Srie

    2016-01-01

    Full Text Available Potassium silicate fertilizer grade were successfully produced by direct fusion of silica (SiO2 and potasium (KOH and K2CO3 in furnaces at temperatures up to melting point of mixture. The geothermal sludge (98% SiO2 and the pyrophyllite (95% SiO2 were used as silica sources. The purposes of the study was to synthesise potassium silicate fertilizer grade having solids concentrations in the range of 31-37% K2O, and silica in the range of 48-54% SiO2. The weight ratio of silicon dioxide/potasium solid being 1:1 to 5:1. Silica from geothermal sludge is amorphous, whereas pyrophylite is crystalline phase. The results showed that the amount of raw materials needed to get the appropriate molar ratio of potassium silicate fertilizer grade are different, as well as the fusion temperature of the furnace. Potassium silicate prepared from potassium hydroxide and geothermal sludge produced a low molar ratio (2.5: 1 to 3: 1. The potassium required quite small (4:1 in weight ratio, and on a fusion temperature of about 900 °C. Meanwhile, the potassium silicate prepared from pyrophyllite produced a high molar ratio (1.4 - 9.4 and on a fusion temperature of about 1350 °C, so that potassium needed large enough to meet the required molar ratio for the fertilizer grade. The product potassium silicate solid is amorphous with a little trace of crystalline.

  2. A natural analogue for copper waste canisters: The copper-uranium mineralised concretions in the Permian mudrocks of south Devon, United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Milodowski, A.E.; Styles, M.T.; Hards, V.L. [Natural Environment Research Council (United Kingdom). British Geological Survey

    2000-08-01

    mineralisation and alteration that can be related to the burial and diagenetic history of the Permian strata. The native copper mineralisation exhibits close temporal association with the formation of uraniferous and vanadiferous concretions (known as 'fish-eyes') in the same rocks. Petrographical relationships indicate that both the copper and the 'fish-eye' concretions formed during burial diagenesis but before the maximum compaction of the host mudstone and siltstone. The regional burial history Wessex Basin, indicates that the maximum compaction of the Permian strata would have been achieved by at least the end of the Lower Jurassic (possibly even in the Triassic). Therefore, the native copper mineralisation is older than 176 Ma. The native copper sheets display a complex sequence of alteration and subsequent mineral growth of minerals on their surfaces. The earliest alteration was to copper oxides - principally cuprite with minor tenorite, indicating a change to more oxidising groundwater conditions. The dissolution of native silver and the growth of fringes of copper arsenides followed this. Nickel arsenides and chalcocite, associated with the precipitation of uranium silicates occurred in the later stages of alteration. This suggests a return to a more reducing pore water environment. Again, petrographical relationships indicate that this alteration and subsequent mineralisation is geologically old (i.e. Lower Jurassic or older). Secondary malachite, intimately intergrown copper sulphate and copper oxides, copper chloride, copper-uranium arsenate and uranium vanadates have formed as late-stage alteration products of the native copper and earlier diagenetic cuprite, chalcocite, copper-nickel arsenide and uranium silicate alteration and mineralisation. This latest stage alteration is most probably attributable to near-surface weathering processes. Although the native copper is affected by corrosion, the study has shown that a significant proportion (30

  3. Discovery of ancient silicate stardust in a meteorite.

    Science.gov (United States)

    Nguyen, Ann N; Zinner, Ernst

    2004-03-05

    We have discovered nine presolar silicate grains from the carbonaceous chondrite Acfer 094. Their anomalous oxygen isotopic compositions indicate formation in the atmospheres of evolved stars. Two grains are identified as pyroxene, two as olivine, one as a glass with embedded metal and sulfides (GEMS), and one as an Al-rich silicate. One grain is enriched in 26Mg, which is attributed to the radioactive decay of 26Al and provides information about mixing processes in the parent star. This discovery opens new means for studying stellar processes and conditions in various solar system environments.

  4. Mathematical Viscosity Models for Ternary Metallic and Silicate Melts

    Institute of Scientific and Technical Information of China (English)

    FU Yuan-kun; MENG Xian-min; GUO Han-jie

    2004-01-01

    The mathematical viscosity models for metallic melts were discussed. The experimental data of Ag-Au-Cu systems were used to verify the models based on Chou's general geometric thermodynamic model and the calculated results are consistent with the reported experimental data. A new model predicting the viscosity of multi-component silicate melts was established. The CaO-MnO-SiO2, CaO-FeO-SiO2 and FeO-MnO-SiO2 silicate slag systems were used to verify the model.

  5. Thermal Expansion and Thermal Conductivity of Rare Earth Silicates

    Science.gov (United States)

    Zhu, Dongming; Lee, Kang N.; Bansal, Narottam P.

    2006-01-01

    Rare earth silicates are considered promising candidate materials for environmental barrier coatings applications at elevated temperature for ceramic matrix composites. High temperature thermophysical properties are of great importance for coating system design and development. In this study, the thermal expansion and thermal conductivity of hot-pressed rare earth silicate materials were characterized at temperatures up to 1400 C. The effects of specimen porosity, composition and microstructure on the properties were also investigated. The materials processing and testing issues affecting the measurements will also be discussed.

  6. Leaf application of silicic acid to upland rice and corn

    Directory of Open Access Journals (Sweden)

    Carlos Alexandre Costa Crusciol

    2013-12-01

    Full Text Available This study aimed to evaluate the effect of Si (stabilized silicic acid, Silamol® leaf application on mineral nutrition and yield in upland rice and corn crops. The treatments were the control (without Si and Si foliar split spraying using 2 L ha-1 of the Silamol® commercial product, with 0.8% soluble Si as concentrated stabilized silicic acid. Silicon leaf application increased the concentrations of K, Ca and Si in rice and corn leaves, the number of panicles per m2 of rice and the number of grains per ear of corn; accordingly, the Si leaf application provided a higher grain yield in both crops.

  7. Mbosi: An anomalous iron with unique silicate inclusions

    Science.gov (United States)

    Olsen, Edward J.; Clayton, Robert N.; Mayeda, Toshiko K.; Davis, Andrew M.; Clarke, Roy S., Jr.; Wasson, John T.

    1996-09-01

    The Mbosi iron meteorite contains millimeter size silicate inclusions. Mbosi is an ungrouped iron meteorite with a Ge/Ga ratio >10, which is an anomalous property shared with the five-member IIF iron group, the Eagle Station pallasites and four other ungrouped irons. Neither the IIF group nor the four other ungrouped irons are known to have silicate inclusions. Chips from three Mbosi inclusions were studied, but most of the work concentrated on a whole 3.1 mm circular inclusion. This inclusion consists of a mantle and a central core of different mineralogies. The mantle is partially devitrified quartz-normative glass, consisting of microscopic crystallites of two pyroxenes and plagioclase, which are crystalline enough to give an x-ray powder diffraction pattern but not coarse enough to permit analyses of individual minerals. The core consists of silica. The bulk composition does not match any known meteorite type, although there is a similarity in mode of occurrence to quartz-normative silicate inclusions in some HE irons. Mbosi silicate appears to be unique. The bulk rare earth element (REE) pattern of the mantle is flat at ≅ 7×C1; the core is depleted in REE but shows a small positive Eu anomaly. The O-isotope composition of bulk silicate lies on a unit slope mixing line (parallel and close to the C3 mixing line) that includes the Eagle Station pallasites and the iron Bocaiuva (related to the IIF irons); all of these share the property of having Ge/Ga ratios >10. It is concluded that Mbosi silicate represents a silica-bearing source rock that was melted and injected into metal. Melting occurred early in the history of the parent body because the metal now shows a normal Widmanstätten structure with only minor distortion that was caused when the parent body broke up and released meteorites into interplanetary space. The cause of Ge/Ga ratios being >10 in these irons is unknown. The fact that silicates in Mbosi, Bocaiuva (related to IIF irons) and the Eagle

  8. Electrical conductivity measurements on silicate melts using the loop technique

    Science.gov (United States)

    Waff, H. S.

    1976-01-01

    A new method is described for measurement of the electrical conductivity of silicate melts under controlled oxygen partial pressure at temperatures to 1550 C. The melt samples are suspended as droplets on platinum-rhodium loops, minimizing iron loss from the melt due to alloying with platinum, and providing maximum surface exposure of the melt to the oxygen-buffering gas atmosphere. The latter provides extremely rapid equilibration of the melt with the imposed oxygen partial pressure. The loop technique involves a minimum of setup time and cost, provides reproducible results to within + or - 5% and is well suited to electrical conductivity studies on silicate melts containing redox cations.

  9. Chinese Copper Manufacturers Expand Overseas

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>In 2012,China’s apparent copper consumption reached 8.84 million tons,accounting for 43%of the global total demand.Spurred by strong demand,China’s copper smelting capacity roars with annual average growth in domestic copper smelting capacity reaching approx-

  10. Copper Selection Experiment on a Copper Bearing Magnetite Ore%某含铜磁铁矿石选铜试验

    Institute of Scientific and Technical Information of China (English)

    金军

    2016-01-01

    针对某低铜磁铁矿石开展了选铜试验。结果表明:在磨矿细度为-0.074 mm 占75.43%的情况下,以水玻璃+六偏磷酸钠为脉石矿物的抑制剂,MA 为铜矿物的捕收剂,MIBC 为起泡剂,采用1粗2精2扫闭路浮选流程处理矿石,可获得铜品位为19.51%、铜回收率为69.20%的铜精矿。%Copper selection experiment was conducted on a low copper content magnetite ore.The results show that:at the grinding fineness of 75.43% passing 0.074 mm,sodium silicate and sodium hexametaphosphate as gangue inhibitor,MA as copper collector,MIBC as frother,via one roughing-two cleaning -two scavenging closed circuit flotation process,copper concentrate with 19.51% copper and recovery of 69.20% was obtained.

  11. Fabrication and Characterization of Metallic Copper and Copper Oxide Nanoflowers

    Directory of Open Access Journals (Sweden)

    *H. S. Virk

    2011-12-01

    Full Text Available Copper nanoflowers have been fabricated using two different techniques; electro-deposition of copper in polymer and anodic alumina templates, and cytyltrimethal ammonium bromide (CTAB-assisted hydrothermal method. Scanning Electron Microscope (SEM images record some interesting morphologies of metallic copper nanoflowers. Field Emission Scanning Electron Microscope (FESEM has been used to determine morphology and composition of copper oxide nanoflowers. X-ray diffraction (XRD pattern reveals the monoclinic phase of CuO in the crystallographic structure of copper oxide nanoflowers. There is an element of random artistic design of nature, rather than science, in exotic patterns of nanoflowers fabricated in our laboratory.

  12. Copper and Copper Proteins in Parkinson’s Disease

    Directory of Open Access Journals (Sweden)

    Sergio Montes

    2014-01-01

    Full Text Available Copper is a transition metal that has been linked to pathological and beneficial effects in neurodegenerative diseases. In Parkinson’s disease, free copper is related to increased oxidative stress, alpha-synuclein oligomerization, and Lewy body formation. Decreased copper along with increased iron has been found in substantia nigra and caudate nucleus of Parkinson’s disease patients. Copper influences iron content in the brain through ferroxidase ceruloplasmin activity; therefore decreased protein-bound copper in brain may enhance iron accumulation and the associated oxidative stress. The function of other copper-binding proteins such as Cu/Zn-SOD and metallothioneins is also beneficial to prevent neurodegeneration. Copper may regulate neurotransmission since it is released after neuronal stimulus and the metal is able to modulate the function of NMDA and GABA A receptors. Some of the proteins involved in copper transport are the transporters CTR1, ATP7A, and ATP7B and the chaperone ATOX1. There is limited information about the role of those biomolecules in the pathophysiology of Parkinson’s disease; for instance, it is known that CTR1 is decreased in substantia nigra pars compacta in Parkinson’s disease and that a mutation in ATP7B could be associated with Parkinson’s disease. Regarding copper-related therapies, copper supplementation can represent a plausible alternative, while copper chelation may even aggravate the pathology.

  13. Core Formation Timescale, Silicate-Metal Equilibration, and W Diffusivity

    Science.gov (United States)

    Yin, Q.; Jacobsen, B.; Tinker, D.; Lesher, C.

    2004-12-01

    The extent to which material accreted to the proto-Earth and segregated to form the core was chemically and isotopically equilibrated with the silicate mantle is an outstanding problem in planetary science. This is particularly important when attempting to assign a meaningful age for planetary accretion and core formation based on Hf-W isotope systematics. The Earth and other terrestrial planets likely formed by accretion of previously differentiated planetesimals. For the planetesimals themselves the most important energy source for metal-silicate differentiation is the combined radioactive heating due to decay of 26Al (half-life 0.7 Ma) and 60Fe (half-life 1.5 Ma). It is expected that the fractionation of Hf and W during planetesimal core formation will lead to a divergence in the W isotopic compositions of the core and silicate portions of these bodies. This expectation is supported by the enormously radiogenic 182W signatures reported for basaltic eucrites. The observation that the W isotopic compositions of the silicate portions of Earth, Moon and Mars are similar and markedly less radiogenic than eucrites suggests that during planet accretion the pre-differentiated metallic core material containing low 182W must have equilibrated extensively with the more radiogenic (high 182W) silicate material to subdue the ingrowth of 182W in the silicate mantle of the planets. The standard theory of planet formation predicts that after runaway and oligarchic growth, the late stage of planet formation is characterized by impact and merging of Mars-sized objects. This is a tremendously energetic process estimated to raise the temperature of the proto-Earth to about 7000K (a temperature equivalent to a mass spectrometer's plasma source, which indiscriminately ionizes all incoming elements). After the giant impacts, the proto-Earth had a luminosity and surface temperature close to a low mass star for a brief period of time. Stevenson (1990) argued that emulsification caused

  14. Industrial experiment of copper electrolyte purification by copper arsenite

    Institute of Scientific and Technical Information of China (English)

    ZHENG Ya-jie; XIAO Fa-xin; WANG Yong; LI Chun-hua; XU Wei; JIAN Hong-sheng; MA Yut-ian

    2008-01-01

    Copper electrolyte was purified by copper arsenite that was prepared with As2O3. And electrolysis experiments of purified electrolyte were carried out at 235 and 305 A/m2, respectively. The results show that the yield of copper arsenite is up to 98.64% when the molar ratio of Cu to As is 1.5 in the preparation of copper arsenite. The removal rates of Sb and Bi reach 74.11% and 65.60% respectively after copper arsenite is added in electrolyte. The concentrations of As, Sb and Bi in electrolyte nearly remain constant during electrolysis of 13 d. The appearances of cathode copper obtained at 235 and 305 A/m2 are slippery and even, and the qualification rate is 100% according to the Chinese standard of high-pure cathode copper(GB/T467-97).

  15. Precursors for formation of copper selenide, indium selenide, copper indium diselenide, and/or copper indium gallium diselenide films

    Energy Technology Data Exchange (ETDEWEB)

    Curtis, Calvin J; Miedaner, Alexander; Van Hest, Maikel; Ginley, David S

    2014-11-04

    Liquid-based precursors for formation of Copper Selenide, Indium Selenide, Copper Indium Diselenide, and/or copper Indium Galium Diselenide include copper-organoselenides, particulate copper selenide suspensions, copper selenide ethylene diamine in liquid solvent, nanoparticulate indium selenide suspensions, and indium selenide ethylene diamine coordination compounds in solvent. These liquid-based precursors can be deposited in liquid form onto substrates and treated by rapid thermal processing to form crystalline copper selenide and indium selenide films.

  16. Non-conservative controls on distribution of dissolved silicate in Cochin Backwaters

    Digital Repository Service at National Institute of Oceanography (India)

    Balachandran, K.K.; Sankaranarayanan, V.N.; Joseph, T.; Nair, M.

    Cochin backwater system was studied with regard to dissolved silicate (DSi) to understand its seasonal distribution and behaviour during estuarine mixing. Silicate had a linear relationship with salinity during the high river discharge period...

  17. The Effect of Copper

    African Journals Online (AJOL)

    higher (p<0.05) in the broodfish fed CSD0 and CSD1 diets than the other diets. Exposure of Clarias gariepinus fish to copper in water, at concentrations above 1.0mg CuSO4/g elicits adverse ... introduction of a toxicant to an aquatic system ..... Toxicity of four commonly used agrochemicals on. Oreochromis niloticus (L) fry.

  18. The copper-nickel concentration log: A tool for stratigraphic interpretation within the ultramafic and basal zones of the stillwater complex, Montana

    Science.gov (United States)

    Drew, L.J.; Bawiec, W.J.; Page, N.J.; Schuenemeyer, J.H.

    1985-01-01

    An analogue to the electric well log was devised for copper-nickel concentration drill-hole data from the Basal and lower part of the Ultramafic zones of the Stillwater Complex using automated data processing. The copper-nickel concentration logs graphically represent intensity (concentration) values that reflect the distribution of the elements in sulfide and silicate minerals. Four major patterns are recognized by their characteristic variations in copper and nickel intensity: (1) relatively flat, low-level copper-intensity signatures associated with arcuate nickel-intensity patterns that correlate with rocks in the Peridotite member of the Ultramafic zone; (2) arcuate or bulb-like patterns of copper and nickel intensity that correlate closely with the Basal bronzite cumulate member of the Basal zone; (3) complex patterns consisting of intervals of low-intensity copper and moderate-intensity nickel, spikes of high nickel and copper intensity, and high copper intensity associated with low nickel intensity that correlate respectively with cordierite-pyroxene hornfels, massive sulfide, norites and mineralized diabase dikes in the Basal norite member; and (4) large intervals of extremely low copper and nickel intensity that correlate with quartz-orthopyroxene hornfels. The recognition and interpretation of these patterns allow two- and three-dimensional stratigraphic and lithologic reconstructions to be done by means of concentration-log correlations instead of variable quality lithologic logging. ?? 1985.

  19. Presenilin promotes dietary copper uptake.

    Directory of Open Access Journals (Sweden)

    Adam Southon

    Full Text Available Dietary copper is essential for multicellular organisms. Copper is redox active and required as a cofactor for enzymes such as the antioxidant Superoxide Dismutase 1 (SOD1. Copper dyshomeostasis has been implicated in Alzheimer's disease. Mutations in the presenilin genes encoding PS1 and PS2 are major causes of early-onset familial Alzheimer's disease. PS1 and PS2 are required for efficient copper uptake in mammalian systems. Here we demonstrate a conserved role for presenilin in dietary copper uptake in the fly Drosophila melanogaster. Ubiquitous RNA interference-mediated knockdown of the single Drosophila presenilin (PSN gene is lethal. However, PSN knockdown in the midgut produces viable flies. These flies have reduced copper levels and are more tolerant to excess dietary copper. Expression of a copper-responsive EYFP construct was also lower in the midgut of these larvae, indicative of reduced dietary copper uptake. SOD activity was reduced by midgut PSN knockdown, and these flies were sensitive to the superoxide-inducing chemical paraquat. These data support presenilin being needed for dietary copper uptake in the gut and so impacting on SOD activity and tolerance to oxidative stress. These results are consistent with previous studies of mammalian presenilins, supporting a conserved role for these proteins in mediating copper uptake.

  20. Tribological properties of alumina-boria-silicate fabric from 25 C to 850 C

    Science.gov (United States)

    Dellacorte, Christopher

    1989-01-01

    Demanding tribological properties are required of the materials used for the sliding seal between the sidewalls and the lower wall of the variable area hypersonic engine. Temperatures range from room temperature and below to operating temperatures of 1000 C in an environment of air, hydrogen, and water vapor. Candidate sealing materials for this application are an alumina-boria-silicate, ceramic, fabric rope sliding against the engine walls which may be made from copper- or nickel-based alloys. Using a pin-on-disk tribometer, the friction and wear properties of some of these potential materials and possible lubrication methods are evaluated. The ceramic fabric rope displayed unacceptably high friction coefficients (0.6 to 1.3) and, thus, requires lubrication. Sputtered thin films of gold, silver, and CaF2 reduced the friction by a factor of two. Sprayed coatings of boride nitride did not effectively lubricate the fabric. Static heat treatment tests at 950 C indicate that the fabric is chemically attacked by large quantities of silver, CaF2, and boron nitride. Sputtered films or powder impregnation of the fabric with gold may provide adequate lubrication up to 1000 C without showing any chemical attack.

  1. Tribological properties of alumina-boria-silicate fabric from 25 to 850 C

    Science.gov (United States)

    Dellacorte, Christopher

    1988-01-01

    Demanding tribological properties are required of the materials used for the sliding seal between the sidewalls and the lower wall of the variable area hypersonic engine. Temperatures range from room temperature and below to operating temperatures of 1000 C in an environment of air, hydrogen, and water vapor. Candidate sealing materials for this application are an alumina-boria-silicate, ceramic, fabric rope sliding against the engine walls which may be made from copper- or nickel-based alloys. Using a pin-on-disk tribometer, the friction and wear properties of some of these potential materials and possible lubrication methods are evaluated. The ceramic fabric rope displayed unacceptably high friction coefficients (0.6 to 1.3) and, thus, requires lubrication. Sputtered thin films of gold, silver, and CaF2 reduced the friction by a factor of two. Sprayed coatings of boride nitride did not effectively lubricate the fabric. Static heat treatment tests at 950 C indicate that the fabric is chemically attacked by large quantities of silver, CaF2, and boron nitride. Sputtered films or powder impregnation of the fabric with gold may provide adequate lubrication up to 1000 C without showing any chemical attack.

  2. On the Dissolution Behavior of Sulfur in Ternary Silicate Slags

    Science.gov (United States)

    Kang, Youn-Bae; Park, Joo Hyun

    2011-12-01

    Sulfur dissolution behavior, in terms of sulfide capacity ( C S), in ternary silicate slags (molten oxide slags composed of MO - NO - SiO2, where M and N are Ca, Mn, Fe, and Mg), is discussed based on available experimental data. Composition dependence of the sulfur dissolution, at least in the dilute region of sulfur, may be explained by taking into account the cation-anion first-nearest-neighbor (FNN) interaction (stability of sulfide) and the cation-cation second-nearest-neighbor (SNN) interaction over O anion (oxygen proportions in silicate slags). When the Gibbs energy of a reciprocal reaction MO + NS = MS + NO is positive, the sulfide capacity of slags with virtually no SiO2 or low SiO2 concentration decreases as the concentration of MO increases. However, in some slags, as SiO2 concentration increases, replacing NO by MO at a constant SiO2 concentration may increase sulfide capacity when the basicity of NO is less than that of MO. This phenomenon is observed as rotation of iso- C S lines in ternary silicate slags, and it is explained by simultaneous consideration of the stability of sulfide and oxygen proportions in the silicate slags. It is suggested that a solution model for the prediction of sulfide capacity should be based on the actual dissolution mechanism of sulfur rather than on the simple empirical correlation.

  3. Porphyrin-Embedded Silicate Materials for Detection of Hydrocarbon Solvents

    Science.gov (United States)

    2011-01-14

    are naturally occurring in petroleum products . The individual compounds are also used in a range of manufacturing and production processes. The BTEX...478-483. 17. Ueno, Y.; Tate, A.; Niwa, O.; Zhou, H.-S.; Yamada, T.; Honma, I. High benzene selectivity of mesoporous silicate for BTX gas sensing

  4. Energetics of silicate melts from thermal diffusion studies

    Energy Technology Data Exchange (ETDEWEB)

    Walker, D.

    1992-07-01

    Efforts are reported in the following areas: laboratory equipment (multianvils for high P/T work, pressure media, SERC/DL sychrotron), liquid-state thermal diffusion (silicate liquids, O isotopic fractionation, volatiles, tektites, polymetallic sulfide liquids, carbonate liquids, aqueous sulfate solutions), and liquid-state isothermal diffusion (self-diffusion, basalt-rhyolite interdiffusion, selective contamination, chemical diffusion).

  5. Experiments on metal-silicate plumes and core formation.

    Science.gov (United States)

    Olson, Peter; Weeraratne, Dayanthie

    2008-11-28

    Short-lived isotope systematics, mantle siderophile abundances and the power requirements of the geodynamo favour an early and high-temperature core-formation process, in which metals concentrate and partially equilibrate with silicates in a deep magma ocean before descending to the core. We report results of laboratory experiments on liquid metal dynamics in a two-layer stratified viscous fluid, using sucrose solutions to represent the magma ocean and the crystalline, more primitive mantle and liquid gallium to represent the core-forming metals. Single gallium drop experiments and experiments on Rayleigh-Taylor instabilities with gallium layers and gallium mixtures produce metal diapirs that entrain the less viscous upper layer fluid and produce trailing plume conduits in the high-viscosity lower layer. Calculations indicate that viscous dissipation in metal-silicate plumes in the early Earth would result in a large initial core superheat. Our experiments suggest that metal-silicate mantle plumes facilitate high-pressure metal-silicate interaction and may later evolve into buoyant thermal plumes, connecting core formation to ancient hotspot activity on the Earth and possibly on other terrestrial planets.

  6. Decreased water flowing from a forest amended with calcium silicate

    Science.gov (United States)

    Mark B. Green; Amey S. Bailey; Scott W. Bailey; John J. Battles; John L. Campbell; Charles T. Driscoll; Timothy J. Fahey; Lucie C. Lepine; Gene E. Likens; Scott V. Ollinger; Paul G. Schaberg

    2013-01-01

    Acid deposition during the 20th century caused widespread depletion of available soil calcium (Ca) throughout much of the industrialized world. To better understand how forest ecosystems respond to changes in a component of acidification stress, an 11.8-ha watershed was amended with wollastonite, a calcium silicate mineral, to restore available soil Ca to preindustrial...

  7. Estimation of high temperature metal-silicate partition coefficients

    Science.gov (United States)

    Jones, John H.; Capobianco, Christopher J.; Drake, Michael J.

    1992-01-01

    It has been known for some time that abundances of siderophile elements in the upper mantle of the Earth are far in excess of those expected from equilibrium between metal and silicate at low pressures and temperatures. Murthy (1991) has re-examined this excess of siderophile element problem by estimating liquid metal/liquid silicate partition coefficients reduces from their measured values at a lower temperature, implying that siderophile elements become much less siderophilic at high temperatures. Murthy then draws the important conclusion that metal/silicate equilibrium at high temperatures can account for the abundances of siderophile elements in the Earth's mantle. Of course, his conclusion is critically dependent on the small values of the partition coefficients he calculates. Because the numerical values of most experimentally-determined partition coefficients increase with increasing temperature at both constant oxygen fugacity and at constant redox buffer, we think it is important to try an alternative extrapolation for comparison. We have computed high temperature metal/silicate partition coefficients under a different set of assumptions and show that such long temperature extrapolations yield values which are critically dependent upon the presumed chemical behavior of the siderophile elements in the system.

  8. Suppressive effects of a polymer sodium silicate solution on ...

    African Journals Online (AJOL)

    Mohsen

    2015-10-21

    Oct 21, 2015 ... roses are available in almost every color, except blue. Flowers can ... Silicon (Si), as a major soil constituent, is an element that ... crops (such as rice) controls diseases and could reduce ... When the pH is 7.0 or less, silicate ions become ... disease) 0% infected of the whole leaves, (1) leaves showing 0 to.

  9. Ubiquitous high-FeO silicates in enstatite chondrites

    Science.gov (United States)

    Lusby, David; Scott, Edward R. D.; Keil, Klaus

    1987-01-01

    SEM and EMPA were used to determine the mineral contents of four EH3 chondrites. All four showed the dominant enstatite peak, Fs 0-5, with 4-8 percent of FeO-rich pyroxene with Fs 5-20. Among the 542 objects found to contain high-FeO silicates, 18 were chondrules, 381 were rimmed or unrimmed grains, and 143 were aggregates. The high-FeO silicates in these objects are very largely pyroxene with Fs 5-23. Large grains of both FeO-rich and FeO-poor silicates were found to be present in the FeO-rich chondrules. This fact, together with the absence of clasts of FeO-rich chondritic material in the EH3 chondrites, suggests that FeO-rich grains were introduced before or during chondrule formation. It is concluded that FeO-rich and FeO-poor silicates were both present in the nebular region where E chondrites originated.

  10. Determination of boron in silicates after ion exchange separation

    Science.gov (United States)

    Kramer, H.

    1955-01-01

    Existing methods for the determination of boron in silicates are not entirely satisfactory. Separation as the methyl ester is lengthy and frequently erratic. An accurate and rapid method applicable to glass, mineral, ore, and water samples uses ion exchange to remove interfering cations, and boron is determined titrimetrically in the presence of mannitol, using a pH meter to indicate the end point.

  11. Determination of reactivity rates of silicate particle-size fractions

    Directory of Open Access Journals (Sweden)

    Angélica Cristina Fernandes Deus

    2014-04-01

    Full Text Available The efficiency of sources used for soil acidity correction depends on reactivity rate (RR and neutralization power (NP, indicated by effective calcium carbonate (ECC. Few studies establish relative efficiency of reactivity (RER for silicate particle-size fractions, therefore, the RER applied for lime are used. This study aimed to evaluate the reactivity of silicate materials affected by particle size throughout incubation periods in comparison to lime, and to calculate the RER for silicate particle-size fractions. Six correction sources were evaluated: three slags from distinct origins, dolomitic and calcitic lime separated into four particle-size fractions (2, 0.84, 0.30 and <0.30-mm sieves, and wollastonite, as an additional treatment. The treatments were applied to three soils with different texture classes. The dose of neutralizing material (calcium and magnesium oxides was applied at equal quantities, and the only variation was the particle-size material. After a 90-day incubation period, the RER was calculated for each particle-size fraction, as well as the RR and ECC of each source. The neutralization of soil acidity of the same particle-size fraction for different sources showed distinct solubility and a distinct reaction between silicates and lime. The RER for slag were higher than the limits established by Brazilian legislation, indicating that the method used for limes should not be used for the slags studied here.

  12. Phase Diagrams of Silicate Systems: Handbook; Third Issue; Ternary Systems

    Science.gov (United States)

    In the third issue of the handbook Phase Diagrams of Silicate Systems, information is included on the phase relationships in systems containing...radioelectronics, nuclear engineering, etc. Not only are equilibrium phase diagrams presented in the handbook, but the phases existing in the

  13. Calorimetric signature of structural heterogeneity in a ternary silicate glass

    DEFF Research Database (Denmark)

    Zhang, Yanfei; Yang, G.; Yue, Yuanzheng

    2013-01-01

    We investigate the structural heterogeneity in a silicate glass by hyperquenching–annealing–calorimetry approach. The results show a striking phenomenon: two separated sub-Tg relaxation peaks appear on the calorimetric curve of the hyperquenched CaO–MgO–SiO2 glass, implying the existence of two d...

  14. Electron stimulated hydroxylation of a metal supported silicate film.

    Science.gov (United States)

    Yu, Xin; Emmez, Emre; Pan, Qiushi; Yang, Bing; Pomp, Sascha; Kaden, William E; Sterrer, Martin; Shaikhutdinov, Shamil; Freund, Hans-Joachim; Goikoetxea, Itziar; Wlodarczyk, Radoslaw; Sauer, Joachim

    2016-02-01

    Water adsorption on a double-layer silicate film was studied by using infrared reflection-absorption spectroscopy, thermal desorption spectroscopy and scanning tunneling microscopy. Under vacuum conditions, small amounts of silanols (Si-OH) could only be formed upon deposition of an ice-like (amorphous solid water, ASW) film and subsequent heating to room temperature. Silanol coverage is considerably enhanced by low-energy electron irradiation of an ASW pre-covered silicate film. The degree of hydroxylation can be tuned by the irradiation parameters (beam energy, exposure) and the ASW film thickness. The results are consistent with a generally accepted picture that hydroxylation occurs through hydrolysis of siloxane (Si-O-Si) bonds in the silica network. Calculations using density functional theory show that this may happen on Si-O-Si bonds, which are either parallel (i.e., in the topmost silicate layer) or vertical to the film surface (i.e., connecting two silicate layers). In the latter case, the mechanism may additionally involve the reaction with a metal support underneath. The observed vibrational spectra are dominated by terminal silanol groups (ν(OD) band at 2763 cm(-1)) formed by hydrolysis of vertical Si-O-Si linkages. Film dehydroxylation fully occurs only upon heating to very high temperatures (∼ 1200 K) and is accompanied by substantial film restructuring, and even film dewetting upon cycling hydroxylation/dehydroxylation treatment.

  15. Nd3+ Doped Silicate Glass Photonic Crystal Fibres

    Institute of Scientific and Technical Information of China (English)

    YANG Lu-Yun; CHEN Dan-Ping; XIA Jin-An; WANG Chen; JIANG Xiong-Wei; ZHU Cong-Shan; QIU Jian-Rong

    2005-01-01

    @@ We report on the fabrication of two kinds of large core area Nd3+ doped silicate glass photonic crystal fibres, and demonstration of the fibre waveguiding properties. The measured minimum loss of one kind ofibres is 2.5 db/m at 660nm. The fibres sustain only a single mode at least over the wavelength range from 660nm to 980nm.

  16. Silicate Dispersion and Mechanical Reinforcement in Polysiloxane/Layered Silicate Nanocomposites

    KAUST Repository

    Schmidt, Daniel F.

    2010-01-12

    We report the first in-depth comparison of the mechanical properties and equilibrium solvent uptake of a range of polysiloxane nanocomposites based on treated and untreated montmorillonite and fumed silica nanofillers. We demonstrate the ability of equilibrium solvent uptake data (and, thus, overall physical and chemical cross-link density) to serve as a proxy for modulus (combining rubber elasticity and Flory-Rehner theory), hardness (via the theory of Boussinesq), and elongation at break, despite the nonideal nature of these networks. In contrast, we find that tensile and tear strength are not well-correlated with solvent uptake. Interfacial strength seems to dominate equilibrium solvent uptake and the mechanical properties it predicts. In the montmorillonite systems in particular, this results in the surprising consequence that equilibrium solvent uptake and mechanical properties are independent of dispersion state. We conclude that edge interactions play a more significant role than degree of exfoliation, a result unique in the field of polymer nanocomposites. This demonstrates that even a combination of polymer/nanofiller compatibility and thermodynamically stable nanofiller dispersion levels may not give rise to reinforcement. These findings provide an important caveat when attempting to connect structure and properties in polymer nanocomposites, and useful guidance in the design of optimized polymer/layered silicate nanocomposites in particular. © 2009 American Chemical Society.

  17. PREFACE: 5th Baltic Conference on Silicate Materials

    Science.gov (United States)

    Mezinskis, G.; Bragina, L.; Colombo, P.; Frischat, G. H.; Grabis, J.; Greil, P.; Deja, J.; Kaminskas, R.; Kliava, J.; Medvids, A.; Nowak, I.; Siauciunas, R.; Valancius, Z.; Zalite, I.

    2011-12-01

    Logo This Volume of IOP Conference Series: Materials Science and Engineering presents a selection of the contributions to the 5th Baltic Conference on Silicate Materials (BaltSilica2011) held at Riga Technical University, Riga, Latvia from 23-25 May 2011. The conference was organized by Riga Technical University (Latvia) and Kaunas University of Technology (Lithuania). The series of Baltic conferences on silicate materials was started since 2004: the first conference was held in Riga, Latvia, 2004; the second conference was held in Kaunas, Lithuania 2005; the third was held again in Riga, Latvia, 2007, and the fourth was held in Kaunas, Lithuania 2009. BaltSilica 2011 was attended by around 50 participants from Latvia, Lithuania, Estonia, Germany, Poland, Italy, France, Ukraine and Russia. In comparison with previous silicate materials conferences, the broadening of participating countries is an indication of the interest of scientists, engineers and students to exchange research ideas, latest results, and to find new research topics for cooperation in the fields of silicate, high temperature materials, and inorganic nanomaterials. The scientific programme included 8 invited plenary lectures 23 oral presentations and 25 posters [1]. Scientific themes covered in the conference and in this special issue: Natural and Artificial Stone Materials; Traditional and New Ceramic and Glass-Like Materials; Nanoparticles and Nanomaterials. This volume consists of 23 selected proceeding papers. The Editor of this special issue is grateful to all the contributors to BaltSilica 2011. I am also very grateful to the scientific committee, the local organizing committee, the session chairs, the referees who refereed the submitted articles to this issue, and to students from the Department of Silicate, High Temperature and Inorganic Nanomaterials Technology of the Riga Technical University who ensured the smooth running of the conference. Particular thanks goes to eight plenary

  18. Comparative characteristics of copper, copper chloride, and copper bromide vapor lasers

    Energy Technology Data Exchange (ETDEWEB)

    Kazarian, M.A.; Petrash, G.G.; Trofimov, A.N.

    1980-03-01

    The paper reports the results of a comparative study of copper and copper halide vapor lasers emitting in a repetitively-pulsed regime. Copper chloride and copper bromide vapor lasers are found to have identical lasing characteristics under any excitation conditions. These characteristics are different from those of a copper vapor laser. An average lasing power of 13 W has been obtained for all lasers studied for an efficiency of 1%. It is shown that the choice of a laser will largely depend on the laser design suitability for a specific application.

  19. On the silicate crystallinities of oxygen-rich evolved stars and their mass-loss rates

    Science.gov (United States)

    Liu, Jiaming; Jiang, B. W.; Li, Aigen; Gao, Jian

    2017-04-01

    For decades ever since the early detection in the 1990s of the emission spectral features of crystalline silicates in oxygen-rich evolved stars, there is a long-standing debate on whether the crystallinity of the silicate dust correlates with the stellar mass-loss rate. To investigate the relation between the silicate crystallinities and the mass-loss rates of evolved stars, we carry out a detailed analysis of 28 nearby oxygen-rich stars. We derive the mass-loss rates of these sources by modelling their spectral energy distributions from the optical to the far-infrared. Unlike previous studies in which the silicate crystallinity was often measured in terms of the crystalline-to-amorphous silicate mass ratio, we characterize the silicate crystallinities of these sources with the flux ratios of the emission features of crystalline silicates to that of amorphous silicates. This does not require the knowledge of the silicate dust temperatures, which are the major source of uncertainties in estimating the crystalline-to-amorphous silicate mass ratio. With a Pearson correlation coefficient of ∼-0.24, we find that the silicate crystallinities and the mass-loss rates of these sources are not correlated. This supports the earlier findings that the dust shells of low mass-loss rate stars can contain a significant fraction of crystalline silicates without showing the characteristic features in their emission spectra.

  20. Petrophysical Analysis of Siliceous-Ooze Sediments, More Basin, Norwegian Sea

    DEFF Research Database (Denmark)

    Awedalkarim, Ahmed; Sørensen, Morten Kanne; Fabricius, Ida Lykke

    2014-01-01

    Pelagic siliceous-ooze sediments occur above the hydrocarbon reservoir of the Ormen Lange gas field in More Basin, Norwegian Sea. A possible hydrocarbon prospect of siliceous ooze was proposed, but siliceous ooze is significantly different in texture from most commonly known reservoir rocks...

  1. Atypical behaviour of dissolved silicate in the Cochin backwater and Periyar river

    Digital Repository Service at National Institute of Oceanography (India)

    Sankaranarayanan, V.N.; Joseph, T.; Jayalakshmy, K.V.; Balachandran, K.K.

    Dissolved silicate was determined for 1 y (1982-83) covering a wide range of salinity from the estuarine mouth to the fresh water region. Silicate concentration ranged between 0.03 and 4.75 mgl/1. Silicate-salinity relationship was linear...

  2. Production test IP-728 half-plant sodium silicate test. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Geier, R.G.

    1966-07-28

    The sodium silicate addition to the coolant reduced the effluent concentrations of certain radionuclides. Nothing was observed during the course of the test to indicate that sodium silicate could not be used at all plants. However, the reductions obtained in effluent activity are not believed commensurate with the cost of silicate usage.

  3. Microstructure characterisation of freeze linings formed in a copper slag cleaning slag

    Directory of Open Access Journals (Sweden)

    Jansson J.

    2015-01-01

    Full Text Available The initial growth rate of freeze linings on water-cooled elements submerged in molten iron silicate slag is fast. The freeze lining microstructure forming on water cooled steel surface in a high-silica, slag cleaning furnace slag of a direct-to-blister copper smelter is mostly glassy or amorphous. It contains 5-30 μm magnetite crystals, very small and larger copper droplets as well as small magnetite and silicate nuclei embedded in the glassy silica-rich matrix. Chemically the formed freeze linings are more silica-rich than the slag from which they were generated. Magnetite (spinel is the primary phase of the solidifying SCF slag but it does not form a continuous network through the freeze lining. Its strength is given by the intergranular silica-rich phase which initially is glassy or microcrystalline. Due to only partial slag reduction in the SCF process, large magnetite crystals are present in the freeze lining and seem to interact physically with copper droplets.

  4. Immiscible silicate liquids and phosphoran olivine in Netschaëvo IIE silicate: Analogue for planetesimal core-mantle boundaries

    Science.gov (United States)

    Van Roosbroek, Nadia; Hamann, Christopher; McKibbin, Seann; Greshake, Ansgar; Wirth, Richard; Pittarello, Lidia; Hecht, Lutz; Claeys, Philippe; Debaille, Vinciane

    2017-01-01

    We have investigated a piece of the Netschaëvo IIE iron meteorite containing a silicate inclusion by means of electron microprobe analysis (EMPA) and transmission electron microscopy (TEM). Netschaëvo contains chondrule-bearing clasts and impact melt rock clasts were also recently found. The examined inclusion belongs to the latter and is characterized by a porphyritic texture dominated by clusters of coarse-grained olivine and pyroxene, set in a fine-grained groundmass that consists of new crystals of olivine and a hyaline matrix. This matrix material has a quasi-basaltic composition in the inner part of the inclusion, whereas the edge of the inclusion has a lower SiO2 concentration and is enriched in MgO, P2O5, CaO, and FeO. Close to the metal host, the inclusion also contains euhedral Mg-chromite crystals and small (olivine crystallites containing up to 14 wt% P2O5, amorphous material, and interstitial Cl-apatite crystals. The Si-rich silicate glass globules show a second population of Fe-rich silicate glass droplets, indicating they formed by silicate liquid immiscibility. Together with the presence of phosphoran olivine and quenched Cl-apatite, these textures suggest rapid cooling and quenching as a consequence of an impact event. Moreover, the enrichment of phosphorus in the silicate inclusion close to the metal host (phosphoran olivine and Cl-apatite) indicates that phosphorus re-partitioned from the metal into the silicate phase upon cooling. This probably also took place in pallasite meteorites that contain late-crystallizing phases rich in phosphorus. Accordingly, our findings suggest that oxidation of phosphorus might be a general process in core-mantle environments, bearing on our understanding of planetesimal evolution. Thus, the Netschaëvo sample serves as a natural planetesimal core-mantle boundary experiment and based on our temperature estimates, the following sequence of events takes place: (i) precipitation of olivine (1400-1360 °C), (ii) re

  5. Effect of the cooling rate on the phase composition and structure of copper matte converting slags

    Science.gov (United States)

    Selivanov, E. N.; Gulyaeva, R. I.; Udoeva, L. Yu.; Belyaev, V. V.; Pankratov, A. A.

    2009-08-01

    The effect of the cooling rate on the phase composition and microstructure of copper matte converting slags is studied by X-ray diffraction, combined thermogravimetry and calorimetry, mineragraphy, and electron-probe microanalysis. The compositions of oxide and sulfide phases are determined, and the forms of nonferrous metals in slags cooled at a rate of 0.3 and 900°C/s are revealed. At high cooling rates of the slags, iron silicate glass is shown to form apart from sulfide phases. Repeated heating of the slags leads to the development of devitrification, “cold” crystallization, and melting. A decrease in the cooling rate favors an increase in the grain sizes in oxides (magnetite, iron silicates) and sulfides (bornite-, sphalerite, and galena-based solid solutions).

  6. Biological and therapeutic effects of ortho-silicic acid and some ortho-silicic acid-releasing compounds: New perspectives for therapy

    Directory of Open Access Journals (Sweden)

    Jurkić Lela Munjas

    2013-01-01

    Full Text Available Abstract Silicon (Si is the most abundant element present in the Earth's crust besides oxygen. However, the exact biological roles of silicon remain unknown. Moreover, the ortho-silicic acid (H4SiO4, as a major form of bioavailable silicon for both humans and animals, has not been given adequate attention so far. Silicon has already been associated with bone mineralization, collagen synthesis, skin, hair and nails health atherosclerosis, Alzheimer disease, immune system enhancement, and with some other disorders or pharmacological effects. Beside the ortho-silicic acid and its stabilized formulations such as choline chloride-stabilized ortho-silicic acid and sodium or potassium silicates (e.g. M2SiO3; M= Na,K, the most important sources that release ortho-silicic acid as a bioavailable form of silicon are: colloidal silicic acid (hydrated silica gel, silica gel (amorphous silicon dioxide, and zeolites. Although all these compounds are characterized by substantial water insolubility, they release small, but significant, equilibrium concentration of ortho-silicic acid (H4SiO4 in contact with water and physiological fluids. Even though certain pharmacological effects of these compounds might be attributed to specific structural characteristics that result in profound adsorption and absorption properties, they all exhibit similar pharmacological profiles readily comparable to ortho-silicic acid effects. The most unusual ortho-silicic acid-releasing agents are certain types of zeolites, a class of aluminosilicates with well described ion(cation-exchange properties. Numerous biological activities of some types of zeolites documented so far might probably be attributable to the ortho-silicic acid-releasing property. In this review, we therefore discuss biological and potential therapeutic effects of ortho-silicic acid and ortho-silicic acid -releasing silicon compounds as its major natural sources.

  7. Production of ultrahigh purity copper using waste copper nitrate solution.

    Science.gov (United States)

    Choi, J Y; Kim, D S

    2003-04-25

    The production of ultrahigh purity copper (99.9999%) by electrolysis in the presence of a cementation barrier has been attempted employing a waste nitric copper etching solution as the electrolyte. The amount of copper deposited on the cathode increased almost linearly with electrolysis time and the purity of copper was observed to increase as the electrolyte concentration was increased. At some point, however, as the electrolyte concentration increased, the purity of copper decreased slightly. As the total surface area of cementation barrier increased, the purity of product increased. The electrolyte temperature should be maintained below 35 degrees C in the range of investigated electrolysis conditions to obtain the ultrahigh purity copper. Considering that several industrial waste solutions contain valuable metallic components the result of present study may support a claim that electrowinning is a very desirable process for their treatment and recovery.

  8. Mid-IR water and silicate relation in protoplanetary disks

    Science.gov (United States)

    Antonellini, S.; Bremer, J.; Kamp, I.; Riviere-Marichalar, P.; Lahuis, F.; Thi, W.-F.; Woitke, P.; Meijerink, R.; Aresu, G.; Spaans, M.

    2017-01-01

    Context. Mid-IR water lines from protoplanetary disks around T Tauri stars have a detection rate of 50%. Models have identified multiple physical properties of disks such as dust-to-gas mass ratio, dust size power law distribution, disk gas mass, disk inner radius, and disk scale height as potential explanations for the current detection rate. Aims: In this study, we aim to break degeneracies through constraints obtained from observations. We search for a connection between mid-IR water line fluxes and the strength of the 10 μm silicate feature. Methods: We analyze observed water line fluxes from three blends at 15.17, 17.22 and 29.85 μm published earlier and compute the 10 μm silicate feature strength from Spitzer spectra to search for possible trends. We use a series of published ProDiMo thermo-chemical models, to explore disk dust and gas properties, and also the effects of different central stars. In addition, we produced two standard models with different dust opacity functions, and one with a parametric prescription for the dust settling. Results: Our series of models that vary properties of the grain size distribution suggest that mid-IR water emission anticorrelates with the strength of the 10 μm silicate feature. The models also show that the increasing stellar bolometric luminosity simultaneously enhance the strength of this dust feature and the water lines fluxes. No correlation is found between the observed mid-IR water lines and the 10 μm silicate strength. Two-thirds of the targets in our sample show crystalline dust features, and the disks are mainly flaring. Our sample shows the same difference in the peak strength between amorphous and crystalline silicates that was noted in earlier studies, but our models do not support this intrinsic difference in silicate peak strength. Individual properties of our models are not able to reproduce the most extreme observations, suggesting that more complex dust properties (e.g., vertically changing) are

  9. Tongling:Copper Industry Giant Takes Shape

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>Centering on the strategic goal of building "World Copper Capital", Tongling constantly extends its product lines and improves the copper industry chain. Now, the copper industry with a production value of RMB 100 billion has taken shape.As the largest copper wire rod manufacturer in Asia, Tongling Quanwei Copper Technologies Co., Ltd., upon its moving into the local market,

  10. The partitioning of copper among selected phases of geologic media of two porphyry copper districts, Puerto Rico

    Science.gov (United States)

    Learned, R.E.; Chao, T.T.; Sanzolone, R.F.

    1981-01-01

    In experiments designed to determine the manner in which copper is partitioned among selected phases that constitute geologic media, we have applied the five-step sequential extraction procedure of Chao and Theobald to the analysis of drill core, soils, and stream sediments of the Rio Vivi and Rio Tanama porphyry copper districts of Puerto Rico. The extraction procedure affords a convenient means of determining the trace-metal content of the following fractions: (1) Mn oxides and "reactive" Fe oxides; (2) "amorphous" Fe oxides; (3) "crystalline" Fe oxides; (4) sulfides and magnetite; and (5) silicates. An additional extraction between steps (1) and (2) was performed to determine organic-related copper in stream sediments. The experimental results indicate that apportionment of copper among phases constituting geologic media is a function of geochemical environment. Distinctive partitioning patterns were derived from the analysis of drill core from each of three geochemical zones: (a) the supergene zone of oxidation; (b) the supergene zone of enrichment; and (c) the hypogene zone; and similarly, from the analysis of; (d) soils on a weakly leached capping; (e) soils on a strongly leached capping; and (f) active stream sediment. The experimental results also show that geochemical contrasts (anomaly-to-background ratios) vary widely among the five fractions of each sampling medium investigated, and that at least one fraction of each medium provides substantially stronger contrast than does the bulk medium. Fraction (1) provides optimal contrast for stream sediments of the district; fraction (2) provides optimal contrast for soils on a weakly leached capping; fraction (3) provides optimal contrast for soils on a strongly leached capping. Selective extraction procedures appear to have important applications to the orientation and interpretive stages of geochemical exploration. Further investigation and testing of a similar nature are recommended. ?? 1981.

  11. Removal of Cadmium Ions from Aqueous Solution by Silicate-incorporated Hydroxyapatite

    Institute of Scientific and Technical Information of China (English)

    SHI Hebin; ZHONG Hong; LIU Yu; DENG Jinyang

    2007-01-01

    This article reports a preliminary research on silicate-incorporated hydroxyapatite as a new environmental mineral used to remove cadmium ions from aqueous solutions. The silicate-incorporated hydroxyapatite was prepared by coprecipitation and calcining, and silicate was incorporated into the crystal lattice of hydroxyapatite by partial substitution of phosphate. The amount of cadmium ions removed by silicate-incorporated hydroxyapatite was significantly elevated, which was 76% higher than that of pure hydroxyapatite. But the sorption behavior of cadmium ions on silicate-incorporated hydroxyapatite was similar to that of pure hydroxyapatite. Morphological study revealed that silicate incorporation confined the crystal growth and increased the specific surface area of hydroxyapatite,which were in favor of enhancing the cadmium ion sorpfion capacity of the samples. Incorporation of silicate into hydroxyapatite seems to be an effective approach to improve the environmental property of hydroxyapatite on removal of aqueous cadmium ions.

  12. IN SITU INFRARED MEASUREMENTS OF FREE-FLYING SILICATE DURING CONDENSATION IN THE LABORATORY

    Energy Technology Data Exchange (ETDEWEB)

    Ishizuka, Shinnosuke; Kimura, Yuki [Institute of Low Temperature Science, Hokkaido University, Hokkaido Sapporo 060-0819 (Japan); Sakon, Itsuki [Department of Astronomy, School of Science, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan)

    2015-04-20

    We developed a new experimental system for infrared (IR) measurements on free-flying nucleating nanoparticles in situ and applied it to studies on silicate particles. We monitored the condensation of magnesium-bearing silicate nanoparticles from thermally evaporated magnesium and silicon monoxide vapor under an atmosphere of oxygen and argon. The IR spectrum of newly condensed particles showed a spectral feature for non-crystalline magnesium-bearing silicate that is remarkably consistent with the IR spectrum of astronomically observed non-crystalline silicate around oxygen-rich evolved stars. The silicate crystallized at <500 K and eventually developed a high crystallinity. Because of the size effects of nanoparticles, the silicate would be expected to be like a liquid at least during the initial stages of nucleation and growth. Our experimental results therefore suggest decreasing the possible formation temperature of crystalline silicates in dust formation environments with relatively higher pressure.

  13. Participation of bacteria in weathering processes of silicates

    Directory of Open Access Journals (Sweden)

    Peter Javorský

    2005-11-01

    Full Text Available Biological processes presented by the metabolic activity of different species of bacteria adhered at the mineral surfaces are a part of the geochemical processes. These bacteria accelerate, by the production of organic acids into the minerals structural bonds, the leaching of elements and their subsequent and gradual transformation to the secondary minerals. Microbial destructions of silicates are studied in order to processing low-quality mineral raw-materials and the remediation of soils, sediments and waters contaminated by industrial pollutants. The samples of material, used in our research, were obtained at 9 deposits of non-metallic raw-materials in Slovakia. The sediment sample was taken from the area of Baikal Lake. The presence of microorganisms in the matrix most frequently was determined by a subsequent isolation of microorganisms and identification of bacterial species presented in the silicate matrix. The species of Bacillus and Pseudomonas genus were the common representative of the microorganisms.

  14. Chemical Fractionation in the Silicate Vapor Atmosphere of the Earth

    CERN Document Server

    Pahlevan, Kaveh; Eiler, John; 10.1016/j.epsl.2010.10.03

    2010-01-01

    Despite its importance to questions of lunar origin, the chemical composition of the Moon is not precisely known. In recent years, however, the isotopic composition of lunar samples has been determined to high precision and found to be indistinguishable from the terrestrial mantle despite widespread isotopic heterogeneity in the Solar System. In the context of the giant-impact hypothesis, this level of isotopic homogeneity can evolve if the proto-lunar disk and post-impact Earth undergo turbulent mixing into a single uniform reservoir while the system is extensively molten and partially vaporized. In the absence of liquid-vapor separation, such a model leads to the lunar inheritance of the chemical composition of the terrestrial magma ocean. Hence, the turbulent mixing model raises the question of how chemical differences arose between the silicate Earth and Moon. Here we explore the consequences of liquid-vapor separation in one of the settings relevant to the lunar composition: the silicate vapor atmosphere...

  15. Dry reusing and wet reclaiming of used sodium silicate sand

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Based on the characteristics of used sodium silicate sand and the different use requirements for recycled sand, "dry reusing and wet reclaiming of used sodium silicate sand" is considered as the most suitable technique for the used sand. When the recycled sand is used as support sand, the used sand is only reused by dry process including breaking, screening, dust-removal, etc., and it is not necessary that the used sand is reclaimed with strongly rubbing and scraping method, but when the recycled sand is used as facing sand (or single sand), the used sand must be reclaimed by wet method for higher removal rate of the residual binders. The characteristics and the properties of the dry reused sand are compared with the wet reclaimed sand after combining the different use requirements of support sand and facing sand (or single sand), and above the most adaptive scheme has also been validated.

  16. Thermochemistry of Rare Earth Silicates for Environmental Barrier Coatings

    Science.gov (United States)

    Costa, Gustavo; Jacobson, Nathan

    2015-01-01

    Rare earth silicates are promising candidates as environmental protective coatings (EBCs) for silica-forming ceramics and composites in combustion environments since they are predicted to have lower reactivity with the water vapor combustion products. The reactivity of rare earth silicates is assessed by the thermodynamic activity of the silica component which is best measured by Knudsen effusion mass spectrometry (KEMS). Here, we discuss a novel method based on a reducing agent to increase the partial pressure of SiO(g) which is then used to calculate thermodynamic activity of silica in Y2O3-SiO2 and Yb2O3-SiO2 systems. After the KEMS measurements, samples were probed by X-ray diffraction and their phase content was calculated from Rietveld refinement.

  17. Calc-silicate mineralization in active geothermal systems

    Energy Technology Data Exchange (ETDEWEB)

    Bird, D.K.; Schiffman, P.; Elders, W.A.; Williams, A.E.; McDowell, S.D.

    1983-01-01

    The detailed study of calc-silicate mineral zones and coexisting phase relations in the Cerro Prieto geothermal system were used as examples for thermodynamic evaluation of phase relations among minerals of variable composition and to calculate the chemical characteristics of hydrothermal solutions compatible with the observed calc-silicate assemblages. In general there is a close correlation between calculated and observed fluid compositions. Calculated fugacities of O{sub 2} at about 320{degrees}C in the Cerro Prieto geothermal system are about five orders of magnitude less than that at the nearby Salton Sea geothermal system. This observation is consistent with the occurrence of Fe{sup 3+} rich epidotes in the latter system and the presence of prehnite at Cerro Prieto.

  18. Inorganic phosphors in lead-silicate glass for white LEDs

    Science.gov (United States)

    Nikonorov, N. V.; Kolobkova, E. V.; Aseev, V. A.; Bibik, A. Yu.; Nekrasova, Ya. A.; Tuzova, Yu. V.; Novogran, A. I.

    2016-09-01

    Luminescent composites of the "phosphor-in-glass" type, based on a highly reflective lead-silicate matrix and fine-grained powders of YAG:Ce3+ and SiAlON:Eu2+ crystals, are developed and synthesized. Phosphor and glass powders are sintered at a temperature of 550°C to obtain phosphor samples for white LEDs. The composites are analyzed by X-ray diffraction and luminescence spectroscopy. The dependence of the light quantum yield on the SiAlON:Eu2+ content in the samples is investigated. A breadboard of a white LED is designed using a phosphor-in-glass composite based on lead-silicate glass with a low glasstransition temperature. The total emission spectra of a blue LED and glass-based composites are measured. The possibility of generating warm white light by choosing an appropriate composition is demonstrated.

  19. Effective elastic moduli of polymer-layered silicate nanocomposites

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Polymer-layered silicate (PLS) nanocomposites exhibit some mechanical properties that are much better than conventional polymer filled composites. A relatively low content of layered silicate yields a significant enhancement of material performance. After the volume fraction of clay reaches a relatively low "critical value"; however, further increasing does not show a greater stiffening effect. This phenomenon is contrary to previous micromechanical pre-dictions and is not understood well. Based on the analysis on the microstructures of PLS nanocomposites, the present note provides an insight into the physical micromechanisms of the above unexpected phenomenon. The Mori-Tanaka scheme and a numerical method are employed to estimate the effec-tive elastic moduli of such a composite.

  20. Xe and Kr analyses of silicate inclusions from iron meteorites.

    Science.gov (United States)

    Bogard, D. D.; Huneke, J. C.; Burnett, D. S.; Wasserburg, G. J.

    1971-01-01

    Measurements have been conducted of the amounts and isotopic composition of Xe and Kr in silicate inclusions of several iron meteorites. It is shown that the Xe and Kr contents are comparable to chondritic values. The isotopic compositions show trapped gas of both chondritic and atmospheric composition. Large spallation effects occur in some of the meteorites; the spallation spectra in some instances differ from those reported for stone meteorites. In several meteorites, very large neutron capture effects on Br and I occur. All samples have pronounced Xe129 excesses which apparently indicate differences in the formation times from chondrites of less than about 100 million years; however, the presence of trapped Xe132 in silicates which were enclosed in molten Fe-Ni and cooled slowly proves that they were not entirely outgassed, so that some of the Xe129 excess may also be trapped.

  1. Modeling the viscosity of silicate melts containing manganese oxide

    Directory of Open Access Journals (Sweden)

    Kim Wan-Yi

    2013-01-01

    Full Text Available Our recently developed model for the viscosity of silicate melts is applied to describe and predict the viscosities of oxide melts containing manganese oxide. The model requires three pairs of adjustable parameters that describe the viscosities in three systems: pure MnO, MnO-SiO2 and MnO-Al2O3-SiO2. The viscosity of other ternary and multicomponent silicate melts containing MnO is then predicted by the model without any additional adjustable model parameters. Experimental viscosity data are reviewed for melts formed by MnO with SiO2, Al2O3, CaO, MgO, PbO, Na2O and K2O. The deviation of the available experimental data from the viscosities predicted by the model is shown to be within experimental error limits.

  2. Mechanochemical reactions on copper-based compounds

    NARCIS (Netherlands)

    Castricum, H.L.; Bakker, H.; Poels, E.K.

    1999-01-01

    Mechanochemical reactions of copper and copper oxides with oxygen and carbon dioxide are discussed, as well as decomposition and reduction of copper compounds by mechanical milling under high-vacuum conditions.

  3. Oxidation Mechanism of Copper Selenide

    Science.gov (United States)

    Taskinen, Pekka; Patana, Sonja; Kobylin, Petri; Latostenmaa, Petri

    2014-09-01

    The oxidation mechanism of copper selenide was investigated at deselenization temperatures of copper refining anode slimes. The isothermal roasting of synthetic, massive copper selenide in flowing oxygen and oxygen - 20% sulfur dioxide mixtures at 450-550 °C indicate that in both atmospheres the mass of Cu2Se increases as a function of time, due to formation of copper selenite as an intermediate product. Copper selenide oxidises to copper oxides without formation of thick copper selenite scales, and a significant fraction of selenium is vaporized as SeO2(g). The oxidation product scales on Cu2Se are porous which allows transport of atmospheric oxygen to the reaction zone and selenium dioxide vapor to the surrounding gas. Predominance area diagrams of the copper-selenium system, constructed for selenium roasting conditions, indicate that the stable phase of copper in a selenium roaster gas with SO2 is the sulfate CuSO4. The cuprous oxide formed in decomposition of Cu2Se is further sulfated to CuSO4.

  4. Copper and copper-nickel-alloys - An overview

    Energy Technology Data Exchange (ETDEWEB)

    Klassert, Anton; Tikana, Ladji [Deutsches Kupferinstitut e.V. Am Bonneshof 5, 40474 Duesseldorf (Germany)

    2004-07-01

    With the increasing level of industrialization the demand for and the number of copper alloys rose in an uninterrupted way. Today, the copper alloys take an important position amongst metallic materials due to the large variety of their technological properties and applications. Nowadays there exist over 3.000 standardized alloys. Copper takes the third place of all metals with a worldwide consumption of over 15 millions tons per year, following only to steel and aluminum. In a modern industrial society we meet copper in all ranges of the life (electro-technology, building and construction industry, mechanical engineering, automotive, chemistry, offshore, marine engineering, medical applications and others.). Copper is the first metal customized by humanity. Its name is attributed to the island Cyprus, which supplied in the antiquity copper to Greece, Rome and the other Mediterranean countries. The Romans called it 'ore from Cyprus' (aes cyprium), later cuprum. Copper deposited occasionally also dapper and could be processed in the recent stone age simply by hammering. Already in early historical time copper alloys with 20 to 50 percent tin was used for the production of mirrors because of their high reflecting power. Although the elementary nickel is an element discovered only recently from a historical perspective, its application in alloys - without any knowledge of the alloy composition - occurred at least throughout the last 2.000 years. The oldest copper-nickel coin originates from the time around 235 B.C.. Only around 1800 AD nickel was isolated as a metallic element. In particular in the sea and offshore technology copper nickel alloys found a broad field of applications in piping systems and for valves and armatures. The excellent combination of characteristics like corrosion resistance, erosion stability and bio-fouling resistance with excellent mechanical strength are at the basis of this success. An experience of many decades supports the use

  5. Effects of copper content on the shell characteristics of hollow steel spheres manufactured using an advanced powder metallurgy technique

    Institute of Scientific and Technical Information of China (English)

    Hamid Sazegaran; Ali-Reza Kiani-Rashid; Jalil Vahdati Khaki

    2016-01-01

    Metallic hollow spheres are used as base materials in the manufacture of hollow sphere structures and metallic foams. In this study, steel hollow spheres were successfully manufactured using an advanced powder metallurgy technique. The spheres’ shells were character-ized by optical microscopy in conjunction with microstructural image analysis software, scanning electron microscopy (SEM), en-ergy-dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD). The microscopic evaluations revealed that the shells consist of sin-tered iron powder, sintered copper powder, sodium silicate, and porosity regions. In addition, the effects of copper content on various pa-rameters such as shell defects, microcracks, thickness, and porosities were investigated. The results indicated that increasing the copper con-tent results in decreases in the surface fraction of shell porosities and the number of microcracks and an increase in shell thickness.

  6. Dentin-cement Interfacial Interaction: Calcium Silicates and Polyalkenoates

    OpenAIRE

    Atmeh, A.R.; Chong, E.Z.; Richard, G; Festy, F.; Watson, T.F.

    2012-01-01

    The interfacial properties of a new calcium-silicate-based coronal restorative material (Biodentine™) and a glass-ionomer cement (GIC) with dentin have been studied by confocal laser scanning microscopy (CLSM), scanning electron microscopy (SEM), micro-Raman spectroscopy, and two-photon auto-fluorescence and second-harmonic-generation (SHG) imaging. Results indicate the formation of tag-like structures alongside an interfacial layer called the “mineral infiltration zone”, where the alkaline c...

  7. Sulfur Solubility In Silicate Melts: A Thermochemical Model

    Science.gov (United States)

    Moretti, R.; Ottonello, G.

    A termochemical model for calculating sulfur solubility of simple and complex silicate melts has been developed in the framework of the Toop-Samis polymeric approach combined with a Flood - Grjotheim theoretical treatment of silicate slags [1,2]. The model allows one to compute sulfide and sulfate content of silicate melts whenever fugacity of gaseous sulphur is provided. "Electrically equivalent ion fractions" are needed to weigh the contribution of the various disproportion reactions of the type: MOmelt + 1/2S2 ,gas MSmelt+1/2O2 ,gas (1) MOmelt + 1/2S2 ,gas + 3/2O2 ,gas MSO4 ,melt (2) Eqs. 1 and 2 account for the oxide-sulfide and the oxide-sulfate disproportiona- tion in silicate melt. Electrically equivalent ion fractions are computed, in a fused salt Temkin notation, over the appropriate matrixes (anionic and cationic). The extension of such matrixes is calculated in the framework of a polymeric model previously developed [1,2,3] and based on a parameterization of acid-base properties of melts. No adjustable parameters are used and model activities follow the raoultian behavior implicit in the ion matrix solution of the Temkin notation. The model is based on a huge amount of data available in literature and displays a high heuristic capability with virtually no compositional limits, as long as the structural role assigned to each oxide holds. REFERENCES: [1] Ottonello G., Moretti R., Marini L. and Vetuschi Zuccolini M. (2001), Chem. Geol., 174, 157-179. [2] Moretti R. (2002) PhD Thesis, University of Pisa. [3] Ottonello G. (2001) J. Non-Cryst. Solids, 282, 72-85.

  8. Unusual coordination numbers in silicate and aluminate glasses

    Energy Technology Data Exchange (ETDEWEB)

    McMillan, P.F. [Arizona State Univ., Tempe, AZ (United States); Stebbins, J.F. [Stanford Univ., Palo Alto, CA (United States)

    1993-12-31

    Silicon and aluminum are the principal network-forming cations in silicate and aluminosilicate glasses. In most models of glass structure, these are presumed to be in tetrahedral coordination, except for highly aluminous compositions, where VI-coordinated Al is expected. Al{sup VI} and Si{sup VI} species have also been suggested to be formed at high pressure. Recent work has yielded some interesting results regarding the Al and Si coordination chemistry in glasses. In amorphous Al{sub 2}O{sub 3} films prepared by electrochemical deposition, not only Al{sup IV} and Al{sup VI}, but also Al{sup V} species have been recognized. These species have also been observed in glasses and amorphous phases prepared along the SiO{sub 2}-Al{sub 2}O{sub 3} join. The concentration of the five coordinated Al species is highly dependent on composition and glass preparation conditions. Al{sup V} and Al{sup VI} species have also recently been described along the SiO{sub 2}-MgAl{sub 2}O{sub 4} join, where it was previously supposed that all Al was tetrahedral. The behavior of silicon is even more {open_quotes}surprising{close_quotes}. In experiments on alkali silicate glasses quenched from high pressures, the authors found evidence for Si in VI-fold coordination, as expected from high pressure silicate crystal structures, and also for Si{sup V}, a new species in silicate chemistry. The relative abundances of these species are a function of quench pressure and silica content. The Si{sup V} species has also been observed in trace amounts in room pressure glasses, and the authors have investigated its concentration as a function of alkali cation.

  9. Diapiric ascent of silicic magma beneath the Bolivian Altiplano

    OpenAIRE

    Del Potro, R.; M. Díez; Blundy, J.; Camacho, Antonio G.; Gottsmann, Joachim

    2013-01-01

    The vertical transport of large volumes of silicic magma, which drives volcanic eruptions and the long-term compositional evolution of the continental crust, is a highly debated problem. In recent years, dyking has been favored as the main ascent mechanism, but the structural connection between a distributed configuration of melt-filled pores in the source region and shallow magma reservoirs remains unsolved. In the Central Andes, inversion of a new high-resolution Bouguer anomaly data over t...

  10. INORGANIC PHOSPHORS IN GLASS BASED ON LEAD SILICATE GLASSES

    Directory of Open Access Journals (Sweden)

    V. A. Aseev

    2014-09-01

    Full Text Available We created and synthesized luminescent composite of the "phosphor in glass" type, based on the lead-silicate matrix and fine-dispersed powder of cerium-activated yttrium-aluminum garnet crystal. Lead-silicate system (40SiO2- 20PbO-(40-x PbF2-xAlF3, x = 0-25 was chosen as the glassy matrix. Initial glass was reduced to powder (frit for "phosphor in glass" composite with a particle size about 50 µm. Glass frit and powder of commercial YAG:Ce3+ phosphor were mixed in a ratio of 30 to 70 (wt %. Then this composite was pressed in a tablet and sintered on a quartz substrate at 823 К for 30 minutes. Thus, the plane parallel sheet for composite of the "phosphor in glass" was obtained with a diameter equal to 10 mm. For the purpose to reduce the loss of light in the presence of dispersion at a glass-phosphor boundary, optimization of glass mixture was done by adjusting the refractive index. X-ray phase and spectral-luminescent analysis of the derived composite were done. The results of these studies showed that there was no degradation of YAG: Ce powder during sintering. Dependence of luminescence intensity from temperature in the range from room temperature to 473 К was studied. It was shown, that with the phosphor in glass usage thermal quenching of luminescence was reduced in comparison with the silicone. The model of white LED was created with the "phosphor in glass" composite based on lead-silicate glasses with low temperature of vitrifying. The derived LED emits white light with a color temperature of 4370 K, and the luminous efficiency is equal to 58 lm/W. The developed luminescent composite based on the lead-silicate matrix can be used for the production of high-power white light LED.

  11. Scenario of Growing Crops on Silicates in Lunar Gargens

    Science.gov (United States)

    Kozyrovska, N.; Kovalchuk, M.; Negutska, V.; Lar, O.; Korniichuk, O.; Alpatov, A.; Rogutskiy, I.; Kordyum, V.; Foing, B.

    Self-perpetuating gardens will be a practical necessity for humans, living in permanently manned lunar bases. A lunar garden has to supplement less appetizing packaged food brought from the Earth, and the ornamental plants have to serve as valuable means for emotional relaxation of crews in a hostile lunar environment. The plants are less prone to the inevitable pests and diseases when they are in optimum condition, however, in lunar greenhouses there is a threat for plants to be hosts for pests and predators. Although the lunar rocks are microorganism free, there will be a problem with the acquired infection (pathogens brought from the Earth) in the substrate used for the plant growing. On the Moon pests can be removed by total fumigation, including seed fumigation. However, such a treatment is not required when probiotics (biocontrol bacteria) for seed inoculation are used. A consortium of bacteria, controlling plant diseases, provides the production of an acceptable harvest under growth limiting factors and a threatening infection. To model lunar conditions we have used terrestrial alumino-silicate mineral anorthosite (Malyn, Ukraine) which served us as a lunar mineral analog for a substrate composition. With the idea to provide a plant with some essential growth elements siliceous bacterium Paenibacillus sp. has been isolated from alumino-silicate mineral, and a mineral leaching has been simulated in laboratory condition. The combination of mineral anorthosite and siliceous bacteria, on one hand, and a consortium of beneficial bacteria for biocontrol of plant diseases, on the other hand, are currently used in model experiments to examine the wheat and potato growth and production in cultivating chambers under controlled conditions.

  12. Nanoindentation investigation of creep properties of calcium silicate hydrates

    OpenAIRE

    Vandamme, Matthieu; ULM, Franz Josef

    2013-01-01

    The creep properties of calcium silicate hydrates (C-S-H) are assessed by means of nanoindentation creep experiments on a wide range of substoichiometric cement pastes. We observe that, after a few seconds, the measured creep compliance of C-S-H is very well captured by a logarithmic time function. The rate of the logarithmic creep is found to scale in a unique manner with indentation modulus, indentation hardness, and packing density, independent of processing, mix proportions, indenter geom...

  13. The Role of Gas-Silicate Chemisorption Reactions in Modifying Planetary Crusts and Surfaces

    Science.gov (United States)

    King, P. L.; Henley, R. W.; Wykes, J. L.; Renggli, C.; Troitzsch, U.; Clark, D.; O'Neill, H. S.

    2014-12-01

    Evidence for gas-solid reactions is found throughout the solar system: for example, sulfidation reactions in some meteorites and secondary phases coating lunar pyroclastic glasses. On Earth, the products of gas-solid reactions are documented in volcanic systems, metalliferous mineral deposits, impact craters, and on dust or meteorites after passage through the atmosphere - such reactions are also likely on the surfaces of Mars and Venus. To understand the chemical dynamics of such gas-solid reactions, we are undertaking systematic experiments and thermochemical modelling. Experiments were conducted in a vertical gas-mixing furnace at 600 - 800 °C and 1 bar, using SO2and a range of Ca-bearing materials: labradorite, feldspar glass and anorthosite (rock). In each case, anhydrite formed rapidly. In shorter experiments with labradorite, isolated anhydrite is observed surrounded by 'moats' of Ca-depleted silicate. In longer experiments, anhydrite is found as clusters of crystals that, in some cases, extend from the substrate forming precarious 'towers' (Figure). Anhydrite fills cracks in porous samples. We propose that the nucleation and rapid growth of anhydrite on the surface of these Ca-rich phases occurs by chemisorption of SO2(g) molecules with slightly negatively charged oxygen onto available near-surface calcium with slight positive charge. Anhydrite growth is sustained by SO2(g) chemisorption and Ca migration through the reacting silicate lattice, accelerated by increased bond lengths at high temperature. Significantly, the chemisorption reaction indicates that SO2 disproportionates to form both oxidized sulfur (as anhydrite) and a reduced sulfur species (e.g., an S* radical ion). On Earth, in the presence of H2O, the predominant reduced sulfur species is H2S, through an overall reaction: 3CaAl2Si2O8 + 4 SO2(g)+ H2O(g) → 3CaSO4 + 3Al2SiO5 + 3SiO2 + H2S(g)The reduced sulfur may react with gas phase Fe, Ni, Zn and Cu cluster compounds to form metal sulfides

  14. Method 366.0 Determination of Dissolved Silicate in Estuarine and Coastal Watersby Gas Segmented Continuous Flow Colorimetric Analysis

    Science.gov (United States)

    This method provides a procedure for the determination of dissolved silicate concentration in estuarine and coastal waters. The dissolved silicate is mainly in the form of silicic acid, H SiO , in estuarine and 4 4 coastal waters. All soluble silicate, including colloidal silici...

  15. Removal of copper from ferrous scrap

    Science.gov (United States)

    Blander, Milton; Sinha, Shome N.

    1990-01-01

    A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

  16. Variations of serum copper values in pregnancy

    OpenAIRE

    Vukelić Jelka; Kapamadžija Aleksandra; Petrović Đorđe; Grujić Zorica; Novakov-Mikić Aleksandra; Kopitović Vesna; Bjelica Artur

    2012-01-01

    Introduction. Copper is essential micronutrient and has an important role in the human body. The serum copper increases during pregnancy and is doubled at full term. Lower levels of serum copper in pregnancy are connected with some pathological conditions. Objective. The aim of this study was to estimate the levels of serum copper in normal and pathological pregnancies, comparing them with values of serum copper in non-pregnant women, to determine if serum copper is lower in some pathol...

  17. Structure and dynamics of iron doped and undoped silicate glasses

    Science.gov (United States)

    Santos, Cristiane N.; Meneses, Domingos D. S.; Echegut, Patrick; Lecomte, Emmanuel

    2010-03-01

    The optical properties of common silicate glass compositions are well known at room temperature. However, their radiative properties and structural evolution of these glasses with temperature are still largely unexplored. In this work we have measured the emissivity of a set of iron doped and undoped silicate and borosilicate glasses over an unprecedented temperature (up to 1700 K) and spectral range (40 -- 20000 cm-1). This was achieved by means of a home-made apparatus composed of a CO2 laser as the heat source, a black-body reference and two spectrometers. The optical functions were assessed using a dielectric function model [1], and the structure and dynamics of the glassy network, as well the absorption of iron species in different redox states were evidenced. We believe that these new data will help to understand the heat transfer in molten silicates. [4pt] [1] D. D. S. Meneses, G. Gruener, M. Malki, and P. Echegut, J. Non-Cryst. Solids 351, 124 (2005)

  18. Electrical properties of iron doped apatite-type lanthanum silicates

    Institute of Scientific and Technical Information of China (English)

    SHI Qingle; ZHANG Hua

    2012-01-01

    The effect of Fe doping on the electrical properties of lanthanum silicates was investigated.The apatite-type lanthanum silicates La10Si6-xFexO27-x/2 (x=0.2,0.4,0.6,0.8,1.0) were synthesized via sol-gel process.The unit cell volume increased with Fe doping because the ionic radius of Fe3+ ion is larger than that of Si4+ ion.The conductivities of La10Si6-xFexO27 x/2 first increased and then decreased with the increasing of Fe content.The increase of the conductivity might be attributed to the distortion of the cell lattice,which assisted the migration of the interstitial oxygen ions.The decrease of the conductivity might be caused by the lower concentration of interstitial oxygen ions.The optimum Fe doping content in lanthanum silicates was 0.6.La10Si5.4Fe0.6O26.7 exhibited the highest ionic conductivity of 2.712× 10-2 S/cm at 800 ℃.The dependence of conductivity on oxygen partial pressure p(O2) suggested that the conductivity of La10Si6-xFexO27-x/2 was mainly contributed by ionic conductivity.

  19. The Partitioning of Tungsten bwtween Aqueous Fluids and Silicate Melts

    Institute of Scientific and Technical Information of China (English)

    许永胜; 张本仁; 等

    1993-01-01

    An experimental study has been carried out to determine the partition coefficients of tungsten between aqueous fluids and granitic melts at 800℃ and 1.5kb with natural granite as the starting material,The effects of the solution on the partition coefficients of tungsten show a wequence of P>co32->B>H2O.The effects are limited(generally KD<0.3)and the tungsten shows a preferential trend toward the melt over the aqueous fiuid.The value of KD increases with increasing concentration of phosphorus;the KD increases first and then reduces with the concentration of CO32-;when temperature decreases,the KD between the solution of CO32- and the silicate melt increases,and that between the solution of B4O72- and the silicate melt decreases.The partition coefficients of phosphorus and sodium between fluids and silicate melts have been calculated from the concentrations of the elements in the melts.The KD value for phosphorus is 0.38 and that for sodium is 0.56.Evidence shows that the elements tend to become richer and richer in the melts.

  20. In vitro studies of calcium phosphate silicate bone cements.

    Science.gov (United States)

    Zhou, Shuxin; Ma, Jingzhi; Shen, Ya; Haapasalo, Markus; Ruse, N Dorin; Yang, Quanzu; Troczynski, Tom

    2013-02-01

    A novel calcium phosphate silicate bone cement (CPSC) was synthesized in a process, in which nanocomposite forms in situ between calcium silicate hydrate (C-S-H) gel and hydroxyapatite (HAP). The cement powder consists of tricalcium silicate (C(3)S) and calcium phosphate monobasic (CPM). During cement setting, C(3)S hydrates to produce C-S-H and calcium hydroxide (CH); CPM reacts with the CH to precipitate HAP in situ within C-S-H. This process, largely removing CH from the set cement, enhances its biocompatibility and bioactivity. The testing results of cell culture confirmed that the biocompatibility of CPSC was improved as compared to pure C(3)S. The results of XRD and SEM characterizations showed that CPSC paste induced formation of HAP layer after immersion in simulated body fluid for 7 days, suggesting that CPSC was bioactive in vitro. CPSC cement, which has good biocompatibility and low/no cytotoxicity, could be a promising candidate as biomedical cement.

  1. Nickel, copper and cobalt coalescence in copper cliff converter slag

    Directory of Open Access Journals (Sweden)

    Wolf A.

    2016-01-01

    Full Text Available The aim of this investigation is to assess the effect of various additives on coalescence of nickel, copper and cobalt from slags generated during nickel extraction. The analyzed fluxes were silica and lime while examined reductants were pig iron, ferrosilicon and copper-silicon compound. Slag was settled at the different holding temperatures for various times in conditions that simulated the industrial environment. The newly formed matte and slag were characterized by their chemical composition and morphology. Silica flux generated higher partition coefficients for nickel and copper than the addition of lime. Additives used as reducing agents had higher valuable metal recovery rates and corresponding partition coefficients than fluxes. Microstructural studies showed that slag formed after adding reductants consisted of primarily fayalite, with some minute traces of magnetite as the secondary phase. Addition of 5 wt% of pig iron, ferrosilicon and copper-silicon alloys favored the formation of a metallized matte which increased Cu, Ni and Co recoveries. Addition of copper-silicon alloys with low silicon content was efficient in copper recovery but coalescence of the other metals was low. Slag treated with the ferrosilicon facilitated the highest cobalt recovery while copper-silicon alloys with silicon content above 10 wt% resulted in high coalescence of nickel and copper, 87 % and 72 % respectively.

  2. Study of Copper Substitute in High Copper Price Market Environment

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>The high price of copper drives up industry cost,also it is difficult for terminal products to raise price to transfer the cost pressure brought by increase in copper price,as a result downstream consumption markets instead try to seek

  3. Fixation Property of Copper Triazole Wood Preservatives

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    According to AWPA E11-2006 standard,copper fixation rates of several copper-based formulations,such as ammoniacal copper,amine copper,and ammoniacal-ethanolamine copper,as well as alkaline copper quaternary(ACQ),were tested and compared in this paper.And the fixation rates of tebuconazole(TEB) and propiconazole(PPZ) in several formulations,such as copper azole,emulsified type and solvent type,were also compared.The determination of copper content in the leachate was analyzed by atomic absorption spectrom...

  4. INTERACTION OF COPPER BASED PRESERVATIVES WITH WOOD

    Directory of Open Access Journals (Sweden)

    Ali Temiz

    2004-11-01

    Full Text Available Copper is highly toxic to fungi and the element is widely used in many preservative formulations over 50 years. The interactions of wood and copper-based preservatives impact both the performance and the environment aspects of treated wood. Copper might be present in treated wood as coppercellulose complex, copper-lignin complex, and crystalline or amorphous inorganic/organic copper compounds. In this review; it was aimed to investigate the interactions of wood and copper-based preservatives, Copper Adsorpsion factors and copper forms in treated wood

  5. Investigation of synthesized Be-bearing silicate glass as laboratory reference sample at X-ray electron probe microanalysis of silicates

    Science.gov (United States)

    Belozerova, Olga Yu.; Mikhailov, Mikhail A.; Demina, Tamara V.

    2017-01-01

    The article discusses estimates of the stability and homogeneity in Be-Mg-Al-silicate glass produced by the authors and its applicability as a laboratory reference sample for X-ray electron probe microanalysis (EPMA) of Be-bearing silicate matters: crystals and quenching melt (glasses), silicates and oxides. The results were obtained using Superprobe-733 and Superprobe JXA-8200 (JEOL Ltd, Japan) devices. The sample homogeneity was studied on macro (10-100 μm) and micro (1-10 μm) levels and was evaluated by the scheme of dispersion analysis. The applicability of Be-bearing silicate glass as a reference sample for Mg, Al, Si determinations was tested on the international certified reference glasses and laboratory reference samples of minerals with a known composition. The obtained experimental metrological characteristics correspond to the "applied geochemistry" type of analysis (second category) and suggest that Be-bearing silicate glass is appropriate as a laboratory reference sample for EPMA of Be-bearing silicate matters, silicates and oxides. Using Be-Mg-Al-silicate glass as a reference sample we obtained satisfactory data on the composition of both some minerals including cordierite and beryllium cordierite, beryllium indialite, beryl and metastable phases (chrysoberyl, compounds with structure of β-quartz and petalite).

  6. Electroleaching of Copper Waste with Recovery of Copper by Electrodialysis

    Directory of Open Access Journals (Sweden)

    Nuñez P.

    2013-04-01

    Full Text Available A new process to leach and recover copper from solid waste using electric fields was designed. The leaching with electro migration is presented as an alternative to traditional leaching. Preliminary data indicate that the copper ion migration is facilitated by using the electrical potential difference; therefore applying a potential difference in the processes of leaching facilitates the removal of copper. This is especially useful when mineral concentrations are very low. Different phenomena associated with transport of copper in solution are studied to generate a model able predict the state of the copper ion concentration in time. A kinetic model for the process was developed and fitted very well the experimental data.

  7. Synthesis of copper/copper oxide nanoparticles by solution plasma

    Science.gov (United States)

    Saito, Genki; Hosokai, Sou; Tsubota, Masakatsu; Akiyama, Tomohiro

    2011-07-01

    This paper describes the synthesis of copper/copper oxide nanoparticles via a solution plasma, in which the effect of the electrolyte and electrolysis time on the morphology of the products was mainly examined. In the experiments, a copper wire as a cathode was immersed in an electrolysis solution of a K2CO3 with the concentration from 0.001 to 0.50 M or a citrate buffer (pH = 4.8), and was melted by the local-concentration of current. The results demonstrated that by using the K2CO3 solution, we obtained CuO nanoflowers with many sharp nanorods, the size of which decreased with decreasing the concentration of the solution. Spherical particles of copper with/without pores formed when the citrate buffer was used. The pores in the copper nanoparticles appeared when the applied voltage changed from 105 V to 130 V, due to the dissolution of Cu2O.

  8. Alteration of uraniferous and native copper concretions in the Permian mudrocks of south Devon, United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Milodowski, A.E.; Styles, M.T.; Horstwood, M.S.A.; Kemp, S.J. [British Geological Survey, Nottingham (United Kingdom)

    2002-03-01

    This report presents the results of a study of the mineralogy and alteration characteristics of unusual concretions containing sheets of native copper, and uranium-vanadium mineralised concretions, in mudstones and siltstones of the Pennian Littleham Mudstone Formation, at Littleham Cove, south Devon, England. The main objectives of the study were: 1. To investigate the corrosion characteristics of the native copper as a natural analogue for the long-term behaviour of copper canisters, sealed in a compacted clay (bentonite) backfill, that will be used for the deep geological disposal of spent fuel and high-level radioactive waste (HLW). This study developed from an earlier pilot study, which demonstrated that the alteration of the native copper in the concretions from Littleham Cove was mineralogically and chemically complex. 2. To investigate the alteration and oxidation of minerals containing reduced species (e.g. ferrous iron) within the uranium-rich concretions as a natural analogue for the potential effects of oxidation induced by alpha-radiolysis of water in a HLW repository environment. Native copper-bearing concretions in the Littleham Mudstone Formation are very rare. They occur, as thin lenticular disks developed largely along bedding lamina and thin low-angle fractures cutting the bedding laminae the upper part of the formation, about 10 m below the top of the formation. This part of the sequence comprises laterally discontinuous, fine-grained sheet-flood and channel sandstones and siltstones. Some of these sandstones, are more extensively-cemented by copper sulphides (mainly chalcocite), copper arsenides, cobalt-nickel arsenides, and uranium silicate. The thin permeable sandstones and siltstones, and fractures zones around small faults appear to have acted as the conduits for the movement of mineralising fluids through the mudstones. The native copper sheets all show a similar pattern of corrosion and alteration. However, the intensity of alteration is

  9. Mg-perovskite/silicate melt and magnesiowuestite/silicate melt partition coefficients for KLB-1 at 250 Kbars

    Science.gov (United States)

    Drake, Michael J.; Rubie, David C.; Mcfarlane, Elisabeth A.

    1992-01-01

    The partitioning of elements amongst lower mantle phases and silicate melts is of interest in unraveling the early thermal history of the Earth. Because of the technical difficulty in carrying out such measurements, only one direct set of measurements was reported previously, and these results as well as interpretations based on them have generated controversy. Here we report what are to our knowledge only the second set of directly measured trace element partition coefficients for a natural system (KLB-1).

  10. Studies of copper transport in mammalian cells using copper radioisotopes

    Energy Technology Data Exchange (ETDEWEB)

    Camakaris, J.; Voskoboinik, I.; Brooks, H.; Greenough, M. [University of Melbourne, Parkville, VIC (Australia). Department of Genetics; Smith, S. [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia). Radiopharmaceuticals Division; Mercer, J. [Deakin University, Clayton, VIC (Australia). Centre of Cellular and Molecular Biology

    1998-12-31

    The trace element copper poses a major problem for all organisms. It is essential as a number of vital enzymes require it. Copper deficiency can lead to neurological disorders, osteoporosis and weakening of arteries. However Cu is also highly toxic and homeostatic mechanisms have evolved to maintain Cu at levels which satisfy requirements but do not cause toxicity. Toxicity is mediated by the oxidative capacity of Cu and its ability to generate toxic free radicals. There are several acquired and inherited diseases due to either Cu toxicity or Cu deficiency. The study of these diseases facilitates identification of genes and proteins involved in copper homeostasis, and this in turn will provide rational therapeutic approaches. Using the copper radioisotopes {sup 64}Cu (t1/2 = 12.8 hr) and {sup 67}Cu (t1/2 = 61 hr) we have developed a number of systems for studying copper transport in mammalian cells. These include investigation of copper uptake, copper efflux and ligand blot assays for Cu-binding proteins. Our studies have focused on Menkes disease which is an inherited and usually lethal copper deficiency disorder in humans. We have demonstrated that the Menkes protein is directly involved as a copper efflux pump in mammalian cells. Using cells overexpressing the Menkes protein we have provided the first biochemical evidence that this functions as a Cu translocating (across the membrane) P-type ATPase (Voskoboinik et al., FEBS Letters, in press). These studies were carried out using purified plasma membrane vesicles. We are now carrying out structure- function studies on this protein using targeted mutations and assaying using the radiocopper vesicle assay. Recently we have commenced studies on the role of amyloid precursor protein (APP) in copper transport and relationship of this to Alzheimers disease

  11. Confined Water in Layered Silicates: The Origin of Anomalous Thermal Expansion Behavior in Calcium-Silicate-Hydrates.

    Science.gov (United States)

    Krishnan, N M Anoop; Wang, Bu; Falzone, Gabriel; Le Pape, Yann; Neithalath, Narayanan; Pilon, Laurent; Bauchy, Mathieu; Sant, Gaurav

    2016-12-28

    Water, under conditions of nanoscale confinement, exhibits anomalous dynamics, and enhanced thermal deformations, which may be further enhanced when such water is in contact with hydrophilic surfaces. Such heightened thermal deformations of water could control the volume stability of hydrated materials containing nanoconfined structural water. Understanding and predicting the thermal deformation coefficient (TDC, often referred to as the CTE, coefficient of thermal expansion), which represents volume changes induced in materials under conditions of changing temperature, is of critical importance for hydrated solids including: hydrogels, biological tissues, and calcium silicate hydrates, as changes in their volume can result in stress development, and cracking. By pioneering atomistic simulations, we examine the physical origin of thermal expansion in calcium-silicate-hydrates (C-S-H), the binding agent in concrete that is formed by the reaction of cement with water. We report that the TDC of C-S-H shows a sudden increase when the CaO/SiO2 (molar ratio; abbreviated as Ca/Si) exceeds 1.5. This anomalous behavior arises from a notable increase in the confinement of water contained in the C-S-H's nanostructure. We identify that confinement is dictated by the topology of the C-S-H's atomic network. Taken together, the results suggest that thermal deformations of hydrated silicates can be altered by inducing compositional changes, which in turn alter the atomic topology and the resultant volume stability of the solids.

  12. Silicate sulfidation and chemical differences between enstatite chondrites and Earth

    Science.gov (United States)

    Lehner, S. W.; Petaev, M. I.; Buseck, P. R.

    2013-12-01

    Isotopic similarity between the Earth-Moon system and enstatite chondrites (ECs) led to the idea that ECs were Earth's building blocks [1-3]. However, compared to Earth's mantle, ECs have low Fe0/Fe ratios, are enriched in volatile elements, and depleted in refractory lithophile elements and Mg [4]. Therefore, deriving Earth composition from ECs requires a loss of volatiles during or prior to accretion and sequestering a large fraction of Si in the deep Earth. Alternatively, the isotopic similarity between the Earth and ECs is explained by their formation from a common precursor that experienced different evolutionary paths resulting in the chemical difference [4]. The vestiges of such a precursor are still present in the unequilibrated ECs as FeO-rich silicates with O isotopic compositions identical to bulk ECs and Earth [5]. Conversion of such a precursor into the characteristic EC mineral assemblage requires high-temperature processing in an H-poor environment with high fS2 and fO2 close to that of the classic solar nebula [6], consistent with redox conditions inferred from Ti4+/Ti3+ ratios in EC pyroxene [7]. Under such conditions reaction of FeO-rich silicates with S-rich gas results in their replacement by the assemblage of FeO-poor silicates; Fe, Mg, Ca sulfides; free silica; and Si-bearing Fe,Ni metal alloy. The progressive sulfidation of ferromagnesian silicates in chondrules results in loss of Mg and addition of Fe, Mn, S, Na, K and, perhaps, other volatiles [6]. At the advanced stages of silicate sulfidation recorded in the metal-sulfide nodules [8], a portion of Si is reduced and dissolved in the Fe,Ni metal. This process is known to fractionate Si isotopes [9,10] and would explain the differences between the ECs and Earth's mantle [11]. The sulfidation of silicates also produces porous S-rich silica, a peculiar phase observed so far only in the ECs. It consists of a sinewy SiO2-rich framework enclosing numerous vesicles filled with beam

  13. A Plasmodium falciparum copper-binding membrane protein with copper transport motifs

    OpenAIRE

    Choveaux David L; Przyborski Jude M; Goldring JP

    2012-01-01

    Abstract Background Copper is an essential catalytic co-factor for metabolically important cellular enzymes, such as cytochrome-c oxidase. Eukaryotic cells acquire copper through a copper transport protein and distribute intracellular copper using molecular chaperones. The copper chelator, neocuproine, inhibits Plasmodium falciparum ring-to-trophozoite transition in vitro, indicating a copper requirement for malaria parasite development. How the malaria parasite acquires or secretes copper st...

  14. Nanocrystalline copper based microcomposites

    OpenAIRE

    J.P. Stobrawa; Z.M. Rdzawski; W. Głuchowski; J. Domagała-Dubiel

    2012-01-01

    Purpose: The aim of this work was to investigate microstructure, mechanical properties and deformation behavior of copper microcomposites: Cu- Y2O3, Cu- ZrO2 and Cu-WC produced by powder metallurgy techniques.Design/methodology/approach: Tests were made with Cu-Y2O3, Cu-ZrO2 and Cu-WC microcomposites containing up to 2% of a strengthening phase. The materials were fabricated by powder metallurgy techniques, including milling of powders, followed by their compacting and sintering. The main mec...

  15. The Bauschinger Effect in Copper

    DEFF Research Database (Denmark)

    Pedersen, Ole Bøcker; Brown, L .M.; Stobbs, W. M.

    1981-01-01

    A study of the Bauschinger effect in pure copper shows that by comparison with dispersion hardened copper the effect is very small and independent of temperature. This suggests that the obstacles to flow are deformable. A simple composite model based on this principle accounts for the data semi...

  16. Effects of copper(II) and copper oxides on THMs formation in copper pipe.

    Science.gov (United States)

    Li, Bo; Qu, Jiuhui; Liu, Huijuan; Hu, Chengzhi

    2007-08-01

    Little is known about how the growth of trihalomethanes (THMs) in drinking water is affected in copper pipe. The formation of THMs and chlorine consumption in copper pipe under stagnant flow conditions were investigated. Experiments for the same water held in glass bottles were performed for comparison. Results showed that although THMs levels firstly increased in the presence of chlorine in copper pipe, faster decay of chlorine as compared to the glass bottle affected the rate of THMs formation. The analysis of water phase was supplemented by surface analysis of corrosion scales using X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM) and energy dispersive spectroscopy (EDX). The results showed the scales on the pipe surface mainly consisted of Cu(2)O, CuO and Cu(OH)(2) or CuCO(3). Designed experiments confirmed that the fast depletion of chlorine in copper pipe was mainly due to effect of Cu(2)O, CuO in corrosion scales on copper pipe. Although copper(II) and copper oxides showed effect on THMs formation, the rapid consumption of chlorine due to copper oxide made THM levels lower than that in glass bottles after 4h. The transformations of CF, DCBM and CDBM to BF were accelerated in the presence of copper(II), cupric oxide and cuprous oxide. The effect of pH on THMs formation was influenced by effect of pH on corrosion of copper pipe. When pH was below 7, THMs levels in copper pipe was higher as compared to glass bottle, but lower when pH was above 7.

  17. Copper: From neurotransmission to neuroproteostasis

    Directory of Open Access Journals (Sweden)

    Carlos M Opazo

    2014-07-01

    Full Text Available Copper is critical for the Central Nervous System (CNS development and function. In particular, different studies have shown the effect of copper at brain synapses, where it inhibits Long Term Potentation (LTP and receptor pharmacology. Paradoxically, according to recent studies copper is required for a normal LTP response. Copper is released at the synaptic cleft, where it blocks glutamate receptors, which explain its blocking effects on excitatory neurotransmission. Our results indicate that copper also enhances neurotransmission through the accumulation of PSD95 protein, which increase the levels of AMPA receptors located at the plasma membrane of the post-synaptic density. Thus, our findings represent a novel mechanism for the action of copper, which may have implications for the neurophysiology and neuropathology of the CNS. These data indicate that synaptic configuration is sensitive to transient changes in transition metal homeostasis. Our results suggest that copper increases GluA1 subunit levels of the AMPA receptor through the anchorage of AMPA receptors to the plasma membrane as a result of PSD-95 accumulation. Here, we will review the role of copper on neurotransmission of CNS neurons. In addition, we will discuss the potential mechanisms by which copper could modulate neuronal proteostasis (neuroproteostasis in the CNS with focus in the Ubiquitin Proteasome System, which is particularly relevant to neurological disorders such Alzheimer’s disease (AD where copper and protein dyshomeostasis may contribute to neurodegeneration. An understanding of these mechanisms may ultimately lead to the development of novel therapeutic approaches to control metal and synaptic alterations observed in AD patients.

  18. The silicate absorption profile in the ISM towards the heavily obscured nucleus of NGC 4418

    CERN Document Server

    Roche, P F; Gonzalez-Martin, O

    2015-01-01

    The 9.7-micron silicate absorption profile in the interstellar medium provides important information on the physical and chemical composition of interstellar dust grains. Measurements in the Milky Way have shown that the profile in the diffuse interstellar medium is very similar to the amorphous silicate profiles found in circumstellar dust shells around late M stars, and narrower than the silicate profile in denser star-forming regions. Here, we investigate the silicate absorption profile towards the very heavily obscured nucleus of NGC 4418, the galaxy with the deepest known silicate absorption feature, and compare it to the profiles seen in the Milky Way. Comparison between the 8-13 micron spectrum obtained with TReCS on Gemini and the larger aperture spectrum obtained from the Spitzer archive indicates that the former isolates the nuclear emission, while Spitzer detects low surface brightness circumnuclear diffuse emission in addition. The silicate absorption profile towards the nucleus is very similar to...

  19. Equation of state and transport properties of silicates under extreme conditions

    Science.gov (United States)

    Qi, T.; Hamel, S.

    2014-12-01

    Understanding the physical properties of silicates under high temperature and pressure is fundamental to an accurate description of planetary interiors and evolution models. For example, earth's mantle is a rocky silicate shell constituting about 84% of Earth's volume. Possible chemical compositions include SiO2 and some other silicates such as MgSiO3 and CaSiO3. Moreover, Moon forming scenarios often invoke giant impacts between silicate-rich objects.Similarly, the existence of a rocky core or mantle with silicate as the major component is frequently assumed in models of giant planets, such as Jupiter or Saturn and Uranus and Neptune.Consequently, constructing planetary interior and evolution models requires knowledge of silicate's equation of state and its optical and transport properties at high pressures and temperatures.

  20. Analyses of Cometary Silicate Crystals: DDA Spectral Modeling of Forsterite

    Science.gov (United States)

    Wooden, Diane

    2012-01-01

    Comets are the Solar System's deep freezers of gases, ices, and particulates that were present in the outer protoplanetary disk. Where comet nuclei accreted was so cold that CO ice (approximately 50K) and other supervolatile ices like ethane (C2H2) were preserved. However, comets also accreted high temperature minerals: silicate crystals that either condensed (greater than or equal to 1400 K) or that were annealed from amorphous (glassy) silicates (greater than 850-1000 K). By their rarity in the interstellar medium, cometary crystalline silicates are thought to be grains that formed in the inner disk and were then radially transported out to the cold and ice-rich regimes near Neptune. The questions that comets can potentially address are: How fast, how far, and over what duration were crystals that formed in the inner disk transported out to the comet-forming region(s)? In comets, the mass fractions of silicates that are crystalline, f_cryst, translate to benchmarks for protoplanetary disk radial transport models. The infamous comet Hale-Bopp has crystalline fractions of over 55%. The values for cometary crystalline mass fractions, however, are derived assuming that the mineralogy assessed for the submicron to micron-sized portion of the size distribution represents the compositional makeup of all larger grains in the coma. Models for fitting cometary SEDs make this assumption because models can only fit the observed features with submicron to micron-sized discrete crystals. On the other hand, larger (0.1-100 micrometer radii) porous grains composed of amorphous silicates and amorphous carbon can be easily computed with mixed medium theory wherein vacuum mixed into a spherical particle mimics a porous aggregate. If crystalline silicates are mixed in, the models completely fail to match the observations. Moreover, models for a size distribution of discrete crystalline forsterite grains commonly employs the CDE computational method for ellipsoidal platelets (c:a:b=8

  1. Jiangxi Copper Corporation Builds 900,000-Ton Copper Production Capacity

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    <正>The Eastward Refined Copper Expansion Pro- ject of Guixi Smelting Plant under Jiangxi Copper Corporation has output its first lot of Copper cathode,marking the company’s pos- session of a 900,000-ton copper production ca- pacity.Thus the company further strengthens its position as the top 3 of the copper world.

  2. Secondary Copper Industry Entered Rapid Growth Period

    Institute of Scientific and Technical Information of China (English)

    2016-01-01

    In China’s copper output,secondary copper accounts for about 40%,for power cable industry,the usage percentage of secondary copper is about 50%.Under the favorable policy of the government to vigorously support recycling industry,secondary copper rod enterprises begin to expand,and are confident toward the industry’s potentials.

  3. Unravelling the Chemical Nature of Copper Cuprizone

    OpenAIRE

    Messori, L.; Casini, A.; C.Gabbiani; Sorace, L.; Muniz-Miranda, M.; Zatta, P

    2007-01-01

    During the last 50 years, formation of the highly chromogenic copper cuprizone complex has been exploited for spectrophotometric determinations of copper although the precise chemical nature of the resulting species has never been ascertained; we eventually show here, in contrast to current opinion, that copper cuprizone is a copper(III) complex.

  4. Conduction mechanism in bismuth silicate glasses containing titanium

    Science.gov (United States)

    Dult, Meenakshi; Kundu, R. S.; Murugavel, S.; Punia, R.; Kishore, N.

    2014-11-01

    Bismuth silicate glasses mixed with different concentrations of titanium dioxide having compositions xTiO2-(60-x)Bi2O3-40SiO2 with x=0, 5, 10, 15 and 20 were prepared by the normal melt quench technique. The frequency dependence of the ac electrical conductivity of different compositions of titanium bismuth silicate glasses has been studied in the frequency range 10-1 Hz to 10 MHz and in the temperature range 623-703 K. The temperature and frequency dependent conductivity is found to obey Jonscher's universal power law for all the compositions of titanium bismuth silicate glass system. The dc conductivity (σdc), so called crossover frequency (ωH), and frequency exponent (s) have been estimated from the fitting of experimental data of ac conductivity with Jonscher's universal power law. Enthalpy to dissociate the cation from its original site next to a charge compensating center (Hf) and enthalpy of migration (Hm) have also been estimated. The conductivity data have been analyzed in terms of different theoretical models to determine the possible conduction mechanism. Analysis of the conductivity data and the frequency exponent shows that the correlated barrier hopping of electrons between Ti3+ and Ti4+ ions in the glasses is the most favorable mechanism for ac conduction. The temperature dependent dc conductivity has been analyzed in the framework of theoretical variable range hopping model (VRH) proposed by Mott which describe the hopping conduction in disordered semiconducting systems. The various polaron hopping parameters have also been deduced. Mott's VRH model is found to be in good agreement with experimental data and the values of inverse localization length of s-like wave function (α) obtained by this model with modifications suggested by Punia et al. are close to the ones reported for a number of oxide glasses.

  5. Geoengineering potential of artificially enhanced silicate weathering of olivine.

    Science.gov (United States)

    Köhler, Peter; Hartmann, Jens; Wolf-Gladrow, Dieter A

    2010-11-23

    Geoengineering is a proposed action to manipulate Earth's climate in order to counteract global warming from anthropogenic greenhouse gas emissions. We investigate the potential of a specific geoengineering technique, carbon sequestration by artificially enhanced silicate weathering via the dissolution of olivine. This approach would not only operate against rising temperatures but would also oppose ocean acidification, because it influences the global climate via the carbon cycle. If important details of the marine chemistry are taken into consideration, a new mass ratio of CO(2) sequestration per olivine dissolution of about 1 is achieved, 20% smaller than previously assumed. We calculate that this approach has the potential to sequestrate up to 1 Pg of C per year directly, if olivine is distributed as fine powder over land areas of the humid tropics, but this rate is limited by the saturation concentration of silicic acid. In our calculations for the Amazon and Congo river catchments, a maximum annual dissolution of 1.8 and 0.4 Pg of olivine seems possible, corresponding to the sequestration of 0.5 and 0.1 Pg of C per year, but these upper limit sequestration rates come at the environmental cost of pH values in the rivers rising to 8.2. Open water dissolution of fine-grained olivine and an enhancement of the biological pump by the rising riverine input of silicic acid might increase our estimate of the carbon sequestration, but additional research is needed here. We finally calculate with a carbon cycle model the consequences of sequestration rates of 1-5 Pg of C per year for the 21st century by this technique.

  6. SILICATES ON IAPETUS FROM CASSINI’S COMPOSITE INFRARED SPECTROMETER

    Energy Technology Data Exchange (ETDEWEB)

    Young, Cindy L.; Wray, James J. [School of Earth and Atmospheric Sciences, Georgia Institute of Technology, Atlanta, GA (United States); Clark, Roger N. [Planetary Science Institute, Tucson, AZ (United States); Spencer, John R. [Southwest Research Institute, Boulder, CO (United States); Jennings, Donald E. [NASA Goddard Space Flight Center, Greenbelt, MD (United States); Hand, Kevin P.; Carlson, Robert W. [Jet Propulsion Laboratory, Pasadena, CA (United States); Poston, Michael J. [Caltech, Pasadena, CA (United States)

    2015-10-01

    We present the first spectral features obtained from Cassini’s Composite Infrared Spectrometer (CIRS) for any icy moon. The spectral region covered by CIRS focal planes (FP) 3 and 4 is rich in emissivity features, but previous studies at these wavelengths have been limited by low signal-to-noise ratios (S/Ns) for individual spectra. Our approach is to average CIRS FP3 spectra to increase the S/N and use emissivity spectra to constrain the composition of the dark material on Iapetus. We find an emissivity feature at ∼855 cm{sup −1} and a possible doublet at 660 and 690 cm{sup −1} that do not correspond to any known instrument artifacts. We attribute the 855 cm{sup −1} feature to fine-grained silicates, similar to those found in dust on Mars and in meteorites, which are nearly featureless at shorter wavelengths. Silicates on the dark terrains of Saturn’s icy moons have been suspected for decades, but there have been no definitive detections until now. Serpentines reported in the literature at ambient temperature and pressure have features near 855 and 660 cm{sup −1}. However, peaks can shift depending on temperature and pressure, so measurements at Iapetus-like conditions are necessary for more positive feature identifications. As a first investigation, we measured muscovite at 125 K in a vacuum and found that this spectrum does match the emissivity feature near 855 cm{sup −1} and the location of the doublet. Further measurements are needed to robustly identify a specific silicate, which would provide clues regarding the origin and implications of the dark material.

  7. Low-(18)O Silicic Magmas: Why Are They So Rare?

    Energy Technology Data Exchange (ETDEWEB)

    Balsley, S.D.; Gregory, R.T.

    1998-10-15

    LOW-180 silicic magmas are reported from only a small number of localities (e.g., Yellowstone and Iceland), yet petrologic evidence points to upper crustal assimilation coupled with fractional crystallization (AFC) during magma genesis for nearly all silicic magmas. The rarity of 10W-l `O magmas in intracontinental caldera settings is remarkable given the evidence of intense 10W-l*O meteoric hydrothermal alteration in the subvolcanic remnants of larger caldera systems. In the Platoro caldera complex, regional ignimbrites (150-1000 km3) have plagioclase 6180 values of 6.8 + 0.1%., whereas the Middle Tuff, a small-volume (est. 50-100 km3) post-caldera collapse pyroclastic sequence, has plagioclase 8]80 values between 5.5 and 6.8%o. On average, the plagioclase phenocrysts from the Middle Tuff are depleted by only 0.3%0 relative to those in the regional tuffs. At Yellowstone, small-volume post-caldera collapse intracaldera rhyolites are up to 5.5%o depleted relative to the regional ignimbrites. Two important differences between the Middle Tuff and the Yellowstone 10W-180 rhyolites elucidate the problem. Middle Tuff magmas reached water saturation and erupted explosively, whereas most of the 10W-l 80 Yellowstone rhyolites erupted effusively as domes or flows, and are nearly devoid of hydrous phenocrysts. Comparing the two eruptive types indicates that assimilation of 10W-180 material, combined with fractional crystallization, drives silicic melts to water oversaturation. Water saturated magmas either erupt explosively or quench as subsurface porphyrins bejiire the magmatic 180 can be dramatically lowered. Partial melting of low- 180 subvolcanic rocks by near-anhydrous magmas at Yellowstone produced small- volume, 10W-180 magmas directly, thereby circumventing the water saturation barrier encountered through normal AFC processes.

  8. Sealing of cracks in cement using microencapsulated sodium silicate

    Science.gov (United States)

    Giannaros, P.; Kanellopoulos, A.; Al-Tabbaa, A.

    2016-08-01

    Cement-based materials possess an inherent autogenous self-healing capability allowing them to seal, and potentially heal, microcracks. This can be improved through the addition of microencapsulated healing agents for autonomic self-healing. The fundamental principle of this self-healing mechanism is that when cracks propagate in the cementitious matrix, they rupture the dispersed capsules and their content (cargo material) is released into the crack volume. Various healing agents have been explored in the literature for their efficacy to recover mechanical and durability properties in cementitious materials. In these materials, the healing agents are most commonly encapsulated in macrocontainers (e.g. glass tubes or capsules) and placed into the material. In this work, microencapsulated sodium silicate in both liquid and solid form was added to cement specimens. Sodium silicate reacts with the calcium hydroxide in hydrated cement paste to form calcium-silicate-hydrate gel that fills cracks. The effect of microcapsule addition on rheological and mechanical properties of cement is reported. It is observed that the microcapsule addition inhibits compressive strength development in cement and this is observed through a plateau in strength between 28 and 56 days. The improvement in crack-sealing for microcapsule-containing specimens is quantified through sorptivity measurements over a 28 day healing period. After just seven days, the addition of 4% microcapsules resulted in a reduction in sorptivity of up to 45% when compared to specimens without any microcapsule addition. A qualitative description of the reaction between the cargo material and the cementitious matrix is also provided using x-ray diffraction analysis.

  9. Infrared Spectroscopy and Stable Isotope Geochemistry of Hydrous Silicate Glasses

    Energy Technology Data Exchange (ETDEWEB)

    Stolper, Edward

    2007-03-05

    The focus of this DOE-funded project has been the study of volatile components in magmas and the atmosphere. Over the twenty-one year period of this project, we have used experimental petrology and stable isotope geochemistry to study the behavior and properties of volatile components dissolved in silicate minerals and melts and glasses. More recently, we have also studied the concentration and isotopic composition of CO2 in the atmosphere, especially in relation to air quality issues in the Los Angeles basin.

  10. Ultra flat supercontinuum generation in silicate dual core microstructured fiber

    Science.gov (United States)

    Buczynski, R.; Pysz, D.; Martynkien, T.; Lorenc, D.; Kujawa, I.; Nasilowski, T.; Berghmans, F.; Thienpont, H.; Stepien, R.

    2009-08-01

    In this paper we report on ultra flat supercontinuum generation in dual core photonic crystal fiber pumped in the normal dispersion regime. The fiber cladding is fabricated from custom NC21 borosilicate glass while the fiber cores is made of commercially available F2 high index lead-silicate glass from Schott Corp. We investigated the supercontinuum characteristics for single and double core excitation by a Ti:Sapphire oscillator delivering 100 fs pulses centered at 800 nm with an energy of 4.2 nJ. Dual core pumping resulted in appreciable flattening of the supercontinuum spectra in the range 875 - 950 nm.

  11. Kinetics of Cyclohexanone Ammoximation over Titanium Silicate Molecular Sieves

    Institute of Scientific and Technical Information of China (English)

    李永祥; 吴巍; 闵恩泽

    2005-01-01

    An intrinsic kinetics of cyclohexanone ammoximation in the liquid phase over titanium silicate molecular sieves is investigated in an isothermal slurry reactor at different initial reactant concentrations, catalyst loading,and reaction temperature. The rate equations are developed by analyzing data of kinetic measurements. More than 10 side reactions were found. H202 decomposition reaction Inust be considered and other side reactions can be neglected in the kinetic modeling. The predicted values of reaction rates based on the kinetic models are almost consistent with experimental ones. The models have guidance to the selection of reactor types and they are useful to the design and operation of reactor used.

  12. Concentration Quenching in Erbium Doped Bismuth Silicate Glasses

    Institute of Scientific and Technical Information of China (English)

    DAI Shi-Xun; XU Tie-Feng; NIE Qiu-Hua; SHEN Xiang; WANG Xun-Si

    2006-01-01

    @@ Er2 O3-doped bismuth silicate glasses are prepared by the conventional melt-quenching method, and the Er3+ : 4 I13/2 → 4I15/2 fluorescence properties are studied for different Er3+ concentrations. Infrared spectra are measured to estimate the exact content of OH- groups in the samples. Based on the electric dipole-dipole interaction theory,the interaction parameter CEr,Er for the migration rate of Er3+ :4 I13/2 → 4 I13/2 in proposed glasses is calculated.

  13. Cracking phenomena in lithium-di-silicate glass ceramics

    Indian Academy of Sciences (India)

    Rajat Banerjee

    2001-04-01

    Lithium-di-silicate glass ceramic (Li2O, SiO2) with uniformly oriented crystals was placed on a Vickers indentation with extrusion axis horizontally parallel to the base axis. The material was rotated through 0°– 90° and at each angle a 20 N load was applied to ascertain the crack path. It was observed that the crack length decreases and the crack deviates from its original path with increasing angle. The deviation of the crack was correlated with the component of the crack driving force and the theoretical strength of the aligned crystals at different angles.

  14. Transparent silicate glass-ceramics embedding Ni-doped nanocrystals

    OpenAIRE

    2010-01-01

    Recent progress in the development of transparent silicate glass-ceramics embedding Ni-doped nanocrystals as broadband gain media is reviewed. At first, optical properties such as the peak positions, wavelengths lifetimes and quantum efficiencies of the near-infrared emission of nickel-doped oxide crystals are overviewed. The quantum efficiencies of the near-infrared emission of nickel-doped LiGa5O8 and MgGa2O4 were as high as ~1 even at room temperature. Thus these materials are promising ca...

  15. Reaction of Calcium Silicates with Carbon Dioxide and Water

    Science.gov (United States)

    1979-09-26

    for Ca3SiO5 to 22.9 kcal/mole for CaSiO3 . The reaction products were calcium carbonate (CaCO3) and a calcium silicate hydrate of variable...Ca3SiO5, beta-Ca2SiO4, and gamma-Ca2SiO4 if free water is present. Aragonite forms in the absence of free H2O and in the carbonation of CaSiO3 . The

  16. High-temperature silicate volcanism on Jupiter's moon Io.

    Science.gov (United States)

    McEwen, A S; Keszthelyi, L; Spencer, J R; Schubert, G; Matson, D L; Lopes-Gautier, R; Klaasen, K P; Johnson, T V; Head, J W; Geissler, P; Fagents, S; Davies, A G; Carr, M H; Breneman, H H; Belton, M J

    1998-07-03

    Infrared wavelength observations of Io by the Galileo spacecraft show that at least 12 different vents are erupting lavas that are probably hotter than the highest temperature basaltic eruptions on Earth today. In at least one case, the eruption near Pillan Patera, two independent instruments on Galileo show that the lava temperature must have exceeded 1700 kelvin and may have reached 2000 kelvin. The most likely explanation is that these lavas are ultramafic (magnesium-rich) silicates, and this idea is supported by the tentative identification of magnesium-rich orthopyroxene in lava flows associated with these high-temperature hot spots.

  17. In vitro bioactivity and cytocompatibility of tricalcium silicate

    Indian Academy of Sciences (India)

    Xiaoming Liao; Hongyang Zhu; Guangfu Yin; Zhongbing Huang; Yadong Yao; Xianchun Chen

    2011-08-01

    The in vitro bioactivity of tricalcium silicate (Ca3SiO5) ceramics was investigated by the bone-like apatite-formation ability in simulated body fluid (SBF), and the cytocompatibility was evaluated through osteoblast adhesion and proliferation assay. The results show that the Ca3SiO5 ceramics possess bone-like apatite formation ability in SBF. In vitro cytocompatible evaluation reveals that osteoblasts adhere and spread well on the Ca3SiO5 ceramics, indicating good bioactivity and cytocompatibility.

  18. Calorimetric signature of structural heterogeneity in a ternary silicate glass

    DEFF Research Database (Denmark)

    Zhang, Yanfei; Yang, G.; Yue, Yuanzheng

    2013-01-01

    distinct structural domains of higher and lower potential energies, respectively. The higher energy domains in nanoscale are so unstable that they become ordered during hyperquenching. This is verified by the high-resolution transmission electron microscopy image exhibiting nanoordered domains in the glass......We investigate the structural heterogeneity in a silicate glass by hyperquenching–annealing–calorimetry approach. The results show a striking phenomenon: two separated sub-Tg relaxation peaks appear on the calorimetric curve of the hyperquenched CaO–MgO–SiO2 glass, implying the existence of two...

  19. Secondary Copper Consumption and Location in China

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    <正> China is short of copper resources and is alsothe second largest copper consuming country inthe world.The way to overcome the contradic-tion between the resource shortage and fastgrowth in consumption is to import copper rawmaterial in large quantities.Since the 1990’s,China’s import quantity of copper scrap hasincreased considerably.During the last twoyears,China has imported copper scrap worthof US$2.25 billion,1.32 times of the value ofimported copper concentrates in the same pe-riod.China is one of the biggest copper scrap

  20. Ladinian radiolarian fauna, siliceous rock from the Xianshuihe Belt, West Sichuan and their tectonic significance

    Institute of Scientific and Technical Information of China (English)

    LIANG Bin; FENG Qinglai; WANG Quanwei; GUO Jianqiu; ZHONG Changhong; LI Zhenjiang

    2005-01-01

    Ladinian radiolarian fauna, including Muelleritortis, Baumgartneria, Oertlispongus,Paroertlispongus, Pseudoertlispongus, etc., was discovered from the siliceous rock of the Runiange Formation in the Xianshuihe belt, West Sichuan Province. Geochemical test on five samples from the siliceous rock indicates that SiO2 content varies in 71.16%-90.06% and Si/Al ratio, in 49-71, which shows that the siliceous rock contains more terrigenous mud sediments.The siliceous rock is characterized by the large ratios of Al203/(Al203+Fe203) (0.63-0.81) and TiN (>26), the low ratio of V/Y (<2.8), and low vanadium content (<23 μg/g), which are similar to the geochemical characteristics of continental margin siliceous rock. The Ce/Ce* ratios of the four samples vary in 1.02-1.47 and the LaN/CeN ratio, in 0.75-1.07, which imply that the siliceous rock was deposited in the continental margin basin. But only one sample is similar to the oceanic siliceous rock in REE. Turbidite-siliceous rock bearing radiolarian-basalt assemblage and the geochemical characteristics of the siliceous rock indicate that the Xianshuihe belt is in the strong rift stage in the Ladinian age.

  1. Studying regimes of convective heat transfer in the production of high-temperature silicate melts

    Science.gov (United States)

    Volokitin, O. G.; Sheremet, M. A.; Shekhovtsov, V. V.; Bondareva, N. S.; Kuzmin, V. I.

    2016-09-01

    The article presents the results of theoretical and experimental studies of the production of high-temperature silicate melts using the energy of low-temperature plasma in a conceptually new setup. A mathematical model of unsteady regimes of convective heat and mass transfer is developed and numerically implemented under the assumption of non-Newtonian nature of flow in the melting furnace with plasma-chemical synthesis of high-temperature silicate melts. Experiments on melting silicate containing materials were carried out using the energy of low-temperature plasma. The dependence of dynamic viscosity of various silicate materials (basalt, ash, waste of oil shale) was found experimentally.

  2. Dominance of sphingomonads in a copper-exposed biofilm community for groundwater treatment.

    Science.gov (United States)

    Vílchez, R; Pozo, C; Gómez, M A; Rodelas, B; González-López, J

    2007-02-01

    The structure, biological activity and microbial biodiversity of a biofilm used for the removal of copper from groundwater were studied and compared with those of a biofilm grown under copper-free conditions. A laboratory-scale submerged fixed biofilter was fed with groundwater (2.3 l h(-1)) artificially polluted with Cu(II) (15 mg l(-1)) and amended with sucrose (150 mg l(-1)) as carbon source. Between 73 and 90 % of the Cu(II) was removed from water during long-term operation (over 200 days). The biofilm was a complex ecosystem, consisting of eukaryotic and prokaryotic micro-organisms. Scanning electron microscopy revealed marked structural changes in the biofilm induced by Cu(II), compared to the biofilm grown in absence of the heavy metal. Analysis of cell-bound extracellular polymeric substances (EPS) demonstrated a significant modification of the composition of cell envelopes in response to Cu(II). Transmission electron microscopy and energy-dispersive X-ray microanalysis (EDX) showed that copper bioaccumulated in the EPS matrix by becoming bound to phosphates and/or silicates, whereas copper accumulated only intracytoplasmically in cells of eukaryotic microbes. Cu(II) also decreased sucrose consumption, ATP content and alkaline phosphatase activity of the biofilm. A detailed study of the bacterial community composition was conducted by 16S rRNA-based temperature gradient gel electrophoresis (TGGE) profiling, which showed spatial and temporal stability of the species diversity of copper-exposed biofilms during biofilter operation. PCR reamplification and sequencing of 14 TGGE bands showed the prevalence of alphaproteobacteria, with most sequences (78 %) affiliated to the Sphingomonadaceae. The major cultivable colony type in plate counts of the copper-exposed biofilm was also identified as that of Sphingomonas sp. These data confirm a major role of these organisms in the composition of the Cu(II)-removing community.

  3. An Introduction to Copper Deposits in China

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    There are 11 genetic types of copper deposit in China, three of which (porphyry,contact metasomatic and VMS types) are the most important. The copper deposits distribute widely both temporally and spatially in China. The features of copper ores in China are mostly poor in copper tenor and complex in metal associated. The copper metallogeny in China predominantly occurs in three metallogenic megadomains, namely the circum-Pacific, the paleo-Asian and the Tethys-Himalayan.

  4. NMR study of hydrated calcium silicates; Etude par RMN de la structure des silicates de calcium hydrates

    Energy Technology Data Exchange (ETDEWEB)

    Klur, I

    1996-02-26

    Radioactive wastes storage methods are developed by the CEA. As cements are important materials as well for hours living radioisotopes than for years living radioisotopes, a better knowledge of this material will allow to anticipate its behaviour and to obtain safer storage methods. The structure of calcium silicates (C-S-H) (main constituent of cements) have then been determined in this thesis by nuclear magnetic resonance. This method has allow to explain in structural terms, the different calcium rates that can be measured in the C-S-H too. (O.M.) 101 refs.

  5. Enhanced bioactivity of glass ionomer cement by incorporating calcium silicates.

    Science.gov (United States)

    Chen, Song; Cai, Yixiao; Engqvist, Håkan; Xia, Wei

    2016-01-01

    Glass ionomer cements (GIC) are known as a non-bioactive dental cement. During setting the GIC have an acidic pH, driven by the acrylic acid component. It is a challenge to make GIC alkaline without disturbing its mechanical properties. One strategy was to add slowly reacting systems with an alkaline pH. The aim of the present study is to investigate the possibility of forming a bioactive dental material based on the combination of glass ionomer cement and calcium silicates. Two types of GIC were used as control. Wollastonite (CS also denoted β-CaSiO3) or Mineral Trioxide Aggregate (MTA) was incorporated into the 2 types of GIC. The material formulations' setting time, compressive strength, pH and bioactivity were compared between modified GIC and GIC control. Apatite crystals were found on the surfaces of the modified cements but not on the control GIC. The compressive strength of the cement remained with the addition of 20% calcium silicate or 20% MTA after one day immersion. In addition, the compressive strength of GIC modified with 20% MTA had been increased during the 14 d immersion (p < 0 .05).

  6. Flared Disks and Silicate Emission in Young Brown Dwarfs

    CERN Document Server

    Mohanty, S; Natta, A; Fujiyoshi, T; Tamura, M; Barrado y Navascués, D; Mohanty, Subhanjoy; Jayawardhana, Ray; Natta, Antonella; Fujiyoshi, Takuya; Tamura, Motohide; Navascues, David Barrado y

    2004-01-01

    We present mid-infrared photometry of three very young brown dwarfs located in the $\\rho$ Ophiuchi star-forming region -- GY5, GY11 and GY310 --obtained with the Subaru 8-meter telescope. All three sources were detected at 8.6 and 11.7$\\mu$m, confirming the presence of significant mid-infrared excess arising from optically thick dusty disks. The spectral energy distributions of both GY310 and GY11 exhibit strong evidence of flared disks; flat disks can be ruled out for these two brown dwarfs. The data for GY5 show large scatter, and are marginally consistent with both flared and flat configurations. Inner holes a few substellar radii in size are indicated in all three cases (and especially in GY11), in agreement with magnetospheric accretion models. Finally, our 9.7$\\mu$m flux for GY310 implies silicate emission from small grains on the disk surface (though the data do not completely preclude larger grains with no silicate feature). Our results demonstrate that disks around young substellar objects are analog...

  7. High-resolution oxygen-17 NMR of solid silicates

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, K.T.; Wu, Y.; Chmelka, B.F. (Lawrence Berkeley Lab., CA (USA)); Stebbins, J. (Stanford Univ, CA (USA)); Pines, A. (Univ. of California, Berkeley (USA))

    1991-01-02

    Several{sup 17}O-enriched silicates were studied by use of dynamic angle spinning (DAS) and double rotation (DOR) nuclear magnetic resonance spectroscopy. These methods average away second-order quadrupolar interactions by reorienting a sample about a time-dependent axis, thereby yielding high-resolution spectra of oxygen-17 nuclei. A narrow spectral line is observed for each distinct oxygen site at the sum of the isotropic chemical shift and the field-dependent isotropic second-order quadrupolar shift. Resolution is increased by up to 2 orders of magnitude compared to conventional magic angle spinning (MAS) spectra. Crystallographically inequivalent oxygen are now observable as distinct resonances in spectra of polycrystalline silicates such as diopside (CaMgSi{sub 2}{sup 17}O{sub 6}), wollastonite (CaSi{sup 17}O{sub 3}), larnite (Ca{sub 2}Si{sup 17}O{sub 4}), and forsterite (Mg{sub 2}Si{sup 17}O{sub 4}).

  8. A silicate disk in the heart of the Ant

    CERN Document Server

    Chesneau, Olivier; Balick, Bruce; Lagadec, Eric; Matsuura, Mikako; Smith, Nathan; Spang, Alain; Wolf, Sebastian; Zijlstra, Albert A

    2007-01-01

    We aim at getting high spatial resolution information on the dusty core of bipolar planetary nebulae to directly constrain the shaping process. Methods: We present observations of the dusty core of the extreme bipolar planetary nebula Menzel 3 (Mz 3, Hen 2-154, the Ant) taken with the mid-infrared interferometer MIDI/VLTI and the adaptive optics NACO/VLT. The core of Mz 3 is clearly resolved with MIDI in the interferometric mode, whereas it is unresolved from the Ks to the N bands with single dish 8.2 m observations on a scale ranging from 60 to 250 mas. A striking dependence of the dust core size with the PA angle of the baselines is observed, that is highly suggestive of an edge-on disk whose major axis is perpendicular to the axis of the bipolar lobes. The MIDI spectrum and the visibilities of Mz 3 exhibit a clear signature of amorphous silicate, in contrast to the signatures of crystalline silicates detected in binary post-AGB systems, suggesting that the disk might be relatively young. We used radiative-...

  9. The structure of alkali silicate gel by total scattering methods

    KAUST Repository

    Benmore, C.J.

    2010-06-01

    The structure of the alkali silicate gel (ASR) collected from the galleries of Furnas Dam in Brazil was determined by a pair distribution function (PDF) analysis of high energy X-ray diffraction data. Since this method is relatively new to concrete structure analysis a detailed introduction on the PDF method is given for glassy SiO2. The bulk amorphous structure of the dam material is confirmed as no Bragg peaks are observed in the scattered intensity. The real space results show that the local structure of the amorphous material is similar to kanemite (KHSi2O5:3H2O) however the long range layer structure of the crystal is broken up in the amorphous state, so that ordering only persists of the length scale of a few polyhedra. The silicate layer structure is a much more disordered than predicted by molecular dynamics models. The X-ray results are consistent with the molecular dynamics model of Kirkpatrick et al. (2005) [1] which predicts that most of the water resides in pores within the amorphous network rather than in layers. The total scattering data provide a rigorous basis against which other models may also be tested. © 2010.

  10. Relaxation phenomena in rubber/layered silicate nanocomposites

    Directory of Open Access Journals (Sweden)

    2007-12-01

    Full Text Available Broadband Dielectric Spectroscopy (BDS is employed in order to investigate relaxation phenomena occurring in natural rubber (NR, polyurethane rubber (PUR and PUR/NR blend based nanocomposites, reinforced by 10 parts per hundred (phr Layered Silicates (LS. Nanocomposites and matrices were examined under identical conditions in a wide frequency (10–1 to 106 Hz and temperature (–100 to 50°C range. Experimental data are analyzed in terms of electric modulus formalism. The recorded relaxation phenomena include contributions from both the polymer matrices and the nanofiller. Natural rubber is a non-polar material and its performance is only slightly affected by the presence of layered silicates. Polyurethane rubber exhibits four distinct relaxation processes attributed, with ascending relaxation rate, to Interfacial Polarization (IP, glass/rubber transition (α-mode, local motions of polar side groups and small segments of the polymer chain (β, γ-mode. The same processes have been detected in all systems containing PUR. IP is present in all nanocomposites being the slowest recorded process. Finally, pronounced interfacial relaxation phenomena, occurring in the PUR+10 phr LS spectra, are attributed to nanoscale effects of intercalation and exfoliation.

  11. Novel understanding of calcium silicate hydrate from dilute hydration

    KAUST Repository

    Zhang, Lina

    2017-05-13

    The perspective of calcium silicate hydrate (C-S-H) is still confronting various debates due to its intrinsic complicated structure and properties after decades of studies. In this study, hydration at dilute suspension of w/s equaling to 10 was conducted for tricalcium silicate (C3S) to interpret long-term hydration process and investigate the formation, structure and properties of C-S-H. Based on results from XRD, IR, SEM, NMR and so forth, loose and dense clusters of C-S-H with analogous C/S ratio were obtained along with the corresponding chemical formulae proposed as Ca5Si4O13∙6.2H2O. Crystalline structure inside C-S-H was observed by TEM, which was allocated at the foil-like proportion as well as the edge of wrinkles of the product. The long-term hydration process of C3S in dilute suspension could be sketchily described as migration of calcium hydroxide and in-situ growth of C-S-H with equilibrium silicon in aqueous solution relatively constant and calcium varied.

  12. Silicates on Iapetus from Cassini's Composite Infrared Spectrometer

    CERN Document Server

    Young, Cindy L; Clark, Roger N; Spencer, John R; Jennings, Donald E; Hand, Kevin P; Poston, Michael J; Carlson, Robert W

    2015-01-01

    We present the first spectral features obtained from Cassini's Composite Infrared Spectrometer (CIRS) for any icy moon. The spectral region covered by CIRS focal planes (FP) 3 and 4 is rich in emissivity features, but previous studies at these wavelengths have been limited by low signal to noise ratios (S/Rs) for individual spectra. Our approach is to average CIRS FP3 spectra to increase the S/R and use emissivity spectra to constrain the composition of the dark material on Iapetus. We find an emissivity feature at ~855 cm-1 and a possible doublet at 660 and 690 cm-1 that do not correspond to any known instrument artifacts. We attribute the 855 cm-1 feature to fine-grained silicates, similar to those found in dust on Mars and in meteorites, which are nearly featureless at shorter wavelengths. Silicates on the dark terrains of Saturn's icy moons have been suspected for decades, but there have been no definitive detections until now. Serpentines reported in the literature at ambient temperature and pressure hav...

  13. Ion-specific effects influencing the dissolution of tricalcium silicate

    Energy Technology Data Exchange (ETDEWEB)

    Nicoleau, L. [BASF Research Construction Materials and Systems, BASF Construction Chemicals GmbH, 83308 Trostberg (Germany); Schreiner, E., E-mail: eduard.schreiner@basf.com [BASF Materials and Systems, BASF SE, 67056 Ludwigshafen (Germany); Nonat, A., E-mail: andre.nonat@u-bourgogne.fr [Institut Carnot de Bourgogne, UMR6303 CNRS, 9 avenue Alain Savary, BP 47870, 21078 Dijon Cedex (France)

    2014-05-01

    It has been recently demonstrated that the dissolution kinetics of tricalcium silicate (C{sub 3}S) is driven by the deviation from its solubility equilibrium. In this article, special attention is paid to ions relevant in cement chemistry likely to interact with C{sub 3}S. In order to determine whether specific effects occur at the interface C{sub 3}S–water, particular efforts have been made to model ion activities using Pitzer's model. It has been found that monovalent cations and monovalent anions interact very little with the surface of C{sub 3}S. On the other side, divalent anions like sulfate slow down the dissolution more strongly by modifying the surface charging of C{sub 3}S. Third, aluminate ions covalently bind to surface silicate monomers and inhibit the dissolution in mildly alkaline conditions. The formation and the breaking of these bonds depend on pH and on [Ca{sup 2+}]. Thermodynamic calculations performed using DFT combined with the COSMO-RS solvation method support the experimental findings.

  14. Identification and Practical Application of Silicate-dissolving Bacteria

    Institute of Scientific and Technical Information of China (English)

    LIN Qi-mei; RAO Zheng-hua; SUN Yan-xing; YAO Jun; XING Li-jun

    2002-01-01

    Slime-forming bacteria were isolated from soils, rock surface and earthworm intestine, and their effects on dissolving silicate minerals and tomato growth were examined. One of the bacteria, Bacillus mucilaginosus RGBc13, had particularly strong ability to form slime and dissolve silicates. RGBc13 could also colonize and develop in both non-rhizosphere and rhizosphere soil. Total number of slime-forming bacteria increased from 2.9 × 103 cfu·g- 1and 8.4 × 103 cfu·g-1 to 9.6 × 106 cfu·g-1 and 6.0 × 107 cfu·g-1 in the non-rhizosphere and rhizosphere soils respectively. Potassium and phosphorus nutritional conditions in the rhizosphere were markedly improved through inoculation of this bacterium. Available K and P respectively increased from 25.86 and 3.63mg· kg-1 in the non-rhizosphere soil to 91.23 and 5.74mg· kg-1 in the rhizosphere soil. Tomato biomass increased by 125%, K and P uptakes were more than 150%, greater than the non- inoculation. Thus, there is a potential in applying RGBc13 for improving plant K and P nutrition.

  15. Authigenic Mineralization of Silicates at the Organic-water Interface

    Science.gov (United States)

    McEvoy, B.; Wallace, A. F.

    2015-12-01

    It is relatively common for some fraction of organic material to be preserved in the sedimentary rock record as disseminated molecular fragments. The survival of wholly coherent tissues from primarily soft-bodied organisms is far more unusual. However, the literature is now well- populated with spectacular examples of soft-tissue preservation ranging from a 2,600 year old human brain to the tissues of the Ediacaran biota that have survived ~600 million years. Some of the most exceptional examples of soft tissue preservation are from the Proterozoic-Cambrian transition, however, nearly all modes of fossil preservation during this time are debated. Clay mineral templates have been implicated as playing a role in several types of soft tissue preservation, including Burgess Shale and Beecher's Trilobite-type preservation, and more recently, Bitter Springs-type silicification. Yet, there is still much debate over whether these clay mineral coatings form during early stage burial and diagenesis, or later stage metamorphism. This research addresses this question by using in situ fluid cell Atomic Force Microscopy (AFM) to investigate the nucleation and growth of silicate minerals on model biological surfaces. Herein we present preliminary results on the deposition of hydrous magnesium silicates on self-assembled monolayers (-OH, -COOH, -CH3, and -H2PO3 terminated surfaces) at ambient conditions.

  16. Evidence of yttrium silicate inclusions in YSZ-porcelain veneers.

    Science.gov (United States)

    Stoner, Brian R; Griggs, Jason A; Neidigh, John; Piascik, Jeffrey R

    2014-04-01

    This report introduces the discovery of crystalline defects that can form in the porcelain veneering layer when in contact with yttria-stabilized zirconia (YSZ). The focus was on dental prostheses and understanding the defects that form in the YSZ/porcelain system; however the data reported herein may have broader implications toward the use and stability of YSZ-based ceramics in general. Specimens were cut from fully sintered YSZ plates and veneering porcelain was applied (porcelain veneer. Local EDAX (SEM) was performed in the regions of visible inclusions and showed significant increases in yttrium concentration. TEM specimens also showed apparent inclusions in the porcelain and selected area electron diffraction was performed on these regions and found the inclusions to be crystalline and identified as either yttrium-silicate (Y2 SiO5 ) or yttrium-disilicate (Y2 Si2 O7 ). Micro-CT data showed that yttrium-silicate precipitates were distributed throughout the thickness of the porcelain veneer. Future studies are needed to determine whether many of the premature failures associated with this materials system may be the result of crystalline flaws that form as a result of high temperature yttrium diffusion near the surfaces of YSZ.

  17. Polymer-Layered Silicate Nanocomposites for Cryotank Applications

    Science.gov (United States)

    Miller, Sandi G.; Meador, Michael A.

    2007-01-01

    Previous composite cryotank designs have relied on the use of conventional composite materials to reduce microcracking and permeability. However, revolutionary advances in nanotechnology derived materials may enable the production of ultra-lightweight cryotanks with significantly enhanced durability and damage tolerance, as well as reduced propellant permeability. Layered silicate nanocomposites are especially attractive in cryogenic storage tanks based on results that have been reported for epoxy nanocomposite systems. These materials often exhibit an order of magnitude reduction in gas permeability when compared to the base resin. In addition, polymer-silicate nanocomposites have been shown to yield improved dimensional stability, strength, and toughness. The enhancement in material performance of these systems occurs without property trade-offs which are often observed in conventionally filled polymer composites. Research efforts at NASA Glenn Research Center have led to the development of epoxy-clay nanocomposites with 70% lower hydrogen permeability than the base epoxy resin. Filament wound carbon fiber reinforced tanks made with this nanocomposite had a five-fold lower helium leak rate than the corresponding tanks made without clay. The pronounced reduction observed with the tank may be due to flow induced alignment of the clay layers during processing. Additionally, the nanocomposites showed CTE reductions of up to 30%, as well as a 100% increase in toughness.

  18. Cobalt silicate hierarchical hollow spheres for lithium-ion batteries

    Science.gov (United States)

    Yang, Jun; Guo, Yuanyuan; Zhang, Yufei; Sun, Chencheng; Yan, Qingyu; Dong, Xiaochen

    2016-09-01

    In this paper, the synthesis of cobalt silicate novel hierarchical hollow spheres via a facile hydrothermal method is presented. With a unique hollow structure, the Co2SiO4 provides a large surface area, which can shorten the lithium ions diffusion length and effectively accommodate the volumetic variation during the lithiation/de-lithiation process. Serving as an anode material in lithium-ion battery application, the Co2SiO4 electrode demonstrates a high reversible specific capacity (first-cycle charge capacity of 948.6 mAh g-1 at 100 mA g-1), a cycling durability (specific capacity of 791.4 mAh g-1 after 100 cycles at 100 mA g-1), and a good rate capability (specific capacity of 349.4 mAh g-1 at 10 A g-1). The results indicate that the cobalt silicate hierarchical hollow sphere holds the potential applications in energy storage electrodes.

  19. Interaction of dispersed polyvynil acetate with silicate in finishing materials

    Directory of Open Access Journals (Sweden)

    Runova, R. F.

    1996-12-01

    Full Text Available This article focuses on the processes of interaction between calcium silicate hydrates and dispersed polyvinyl acetate in tight films with the aim of developing compounds meant for restoration and finishing works. The basis of this development relies on the concept concerning the determining role of the crystal-chemical factor of the silicate phase in the formation of organic-mineral compounds of increased durability. The characteristics of dispersed calcium silicate hydrates are portrayed. The preparation conditions, accounting for the synthesis of the product of submicrocrystalline structure, conforming with the stoichiometry CaO∙SiO2 =0.8-2.0 have been determined. The interaction has been studied for compounds achieved by mixing ingredients in a rapid whirling mixer, and subjected to hardening at T=20+2 T. With the aid of XRD, DTA and Infra-Red Spectrometry methods the formation process of the sophisticated polymer silicate phase in the material was observed for a period of 90 days. The properties of the film were investigated and its high resistance against the influence of external factors was established. On this basis a conclusion concerning the quite high effectiveness of substituting portland cement with dispersed calcium silicate hydrate in polymer cement compounds has been made. White colour and other various special properties determine the suitability for repair and finishing works on facades of buildings.

    Este artículo está orientado a estudiar los procesos de interacción entre los silicatos cálcicos hidratados y el acetato de polivinilo disperso en capas impermeables, con el objeto de desarrollar compuestos destinados para la restauración. El fundamento de estos estudios es determinar el papel que los factores cristaloquímicos de las fases silicato tienen en la formación de compuestos órganominerales de elevada durabilidad. Se han descrito las características de los silicatos cálcicos hidratados

  20. Mineral stimulation of subsurface microorganisms: release of limiting nutrients from silicates

    Science.gov (United States)

    Roger, Jennifer Roberts; Bennett, Philip C.

    2004-01-01

    Microorganisms play an important role in the weathering of silicate minerals in many subsurface environments, but an unanswered question is whether the mineral plays an important role in the microbial ecology. Silicate minerals often contain nutrients necessary for microbial growth, but whether the microbial community benefits from their release during weathering is unclear. In this study, we used field and laboratory approaches to investigate microbial interactions with minerals and glasses containing beneficial nutrients and metals. Field experiments from a petroleum-contaminated aquifer, where silicate weathering is substantially accelerated in the contaminated zone, revealed that phosphorus (P) and iron (Fe)-bearing silicate glasses were preferentially colonized and weathered, while glasses without these elements were typically barren of colonizing microorganisms, corroborating previous studies using feldspars. In laboratory studies, we investigated microbial weathering of silicates and the release of nutrients using a model ligand-promoted pathway. A metal-chelating organic ligand 3,4 dihydroxybenzoic acid (3,4 DHBA) was used as a source of chelated ferric iron, and a carbon source, to investigate mineral weathering rate and microbial metabolism.In the investigated aquifer, we hypothesize that microbes produce organic ligands to chelate metals, particularly Fe, for metabolic processes and also form stable complexes with Al and occasionally with Si. Further, the concentration of these ligands is apparently sufficient near an attached microorganism to destroy the silicate framework while releasing the nutrient of interest. In microcosms containing silicates and glasses with trace phosphate mineral inclusions, microbial biomass increased, indicating that the microbial community can use silicate-bound phosphate inclusions. The addition of a native microbial consortium to microcosms containing silicates or glasses with iron oxide inclusions correlated to

  1. Formation of copper-indium-selenide and/or copper-indium-gallium-selenide films from indium selenide and copper selenide precursors

    Energy Technology Data Exchange (ETDEWEB)

    Curtis, Calvin J [Lakewood, CO; Miedaner, Alexander [Boulder, CO; Van Hest, Maikel [Lakewood, CO; Ginley, David S [Evergreen, CO; Nekuda, Jennifer A [Lakewood, CO

    2011-11-15

    Liquid-based indium selenide and copper selenide precursors, including copper-organoselenides, particulate copper selenide suspensions, copper selenide ethylene diamine in liquid solvent, nanoparticulate indium selenide suspensions, and indium selenide ethylene diamine coordination compounds in solvent, are used to form crystalline copper-indium-selenide, and/or copper indium gallium selenide films (66) on substrates (52).

  2. The Revovery of Copper and Cobalt from Oxidized Copper Ore and Converter Slag

    OpenAIRE

    ZİYADANOĞULLARI, Berrin; ZİYADANOĞULLARI, Recep

    1999-01-01

    The aim of this study was to develop a method for obtaining copper and cobalt from oxidized copper ore and converter slag. In order to convert the copper and cobalt into sulfate compounds the main step was to roast the samples obtained by sulfurization and transfer the samples into solution. First the oxidized copper ore was roasted, followed by the mixture of converter slag and oxidized copper ore. Since the levels of copper and cobalt were low, the sulfurization process was carri...

  3. Genome Sequences of Two Copper-Resistant Escherichia coli Strains Isolated from Copper-Fed Pigs

    DEFF Research Database (Denmark)

    Lüthje, Freja L.; Hasman, Henrik; Aarestrup, Frank Møller;

    2014-01-01

    The draft genome sequences of two copper-resistant Escherichia coli strains were determined. These had been isolated from copper-fed pigs and contained additional putative operons conferring copper and other metal and metalloid resistances.......The draft genome sequences of two copper-resistant Escherichia coli strains were determined. These had been isolated from copper-fed pigs and contained additional putative operons conferring copper and other metal and metalloid resistances....

  4. Majorana Electroformed Copper Mechanical Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Overman, Nicole R.; Overman, Cory T.; Kafentzis, Tyler A.; Edwards, Danny J.; Hoppe, Eric W.

    2012-04-30

    The MAJORANA DEMONSTRATOR is a large array of ultra-low background high-purity germanium detectors, enriched in 76Ge, designed to search for zero-neutrino double-beta decay. The DEMONSTRATOR will utilize ultra high purity electroformed copper for a variety of detector components and shielding. A preliminary mechanical evaluation was performed on the Majorana prototype electroformed copper material. Several samples were removed from a variety of positions on the mandrel. Tensile testing, optical metallography, scanning electron microscopy, and hardness testing were conducted to evaluate mechanical response. Analyses carried out on the Majorana prototype copper to this point show consistent mechanical response from a variety of test locations. Evaluation shows the copper meets or exceeds the design specifications.

  5. Hereditary iron and copper deposition

    DEFF Research Database (Denmark)

    Aaseth, Jan; Flaten, Trond Peder; Andersen, Ole

    2007-01-01

    can be successfully treated, emphasizing the importance of early diagnosis. Serum ferritin values, transferrin saturation and genetic analysis are used when diagnosing haemochromatosis. The diagnostics of Wilson's disease depends on the use of urinary copper values, serum ceruloplasmin and liver...

  6. Influence of silicate on the transport of bacteria in quartz sand and iron mineral-coated sand.

    Science.gov (United States)

    Dong, Zhe; Yang, Haiyan; Wu, Dan; Ni, Jinren; Kim, Hyunjung; Tong, Meiping

    2014-11-01

    The influence of silicate on the transport and deposition of bacteria (Escherichia coli) in packed porous media were examined at a constant 20 mM ionic strength with different silicate concentrations (from 0 to 1 mM) at pH 7. Transport experiments were performed in two types of representative porous media, both bare quartz sand and iron mineral-coated quartz sand. In bare quartz sand, the breakthrough plateaus in the presence of silicate in suspensions were lower and the corresponding retained profiles were higher than those without silicate ions, indicating that the presence of silicate in suspensions decreased cell transport in bare quartz sand. Moreover, the decrease of bacteria transport in quartz sand induced by silicate was more pronounced with increasing silicate concentrations from 0 to 1 mM. However, when EPS was removed from cell surfaces, the presence of silicate in cell suspensions (with different concentrations) did not affect the transport behavior of bacteria in quartz sand. The interaction of silicate with EPS on cell surfaces negatively decreased the zeta potentials of bacteria, resulting in the decreased cell transport in bare quartz sand when silicate was copresent in bacteria suspensions. In contrast, the presence of silicate in suspensions increased cell transport in iron mineral-coated sand. Silicate ions competed with bacteria for the adsorption sites on mineral-coated sand, contributing to the increased cell transport in mineral-coated sand with silicate present in cell suspensions.

  7. A study of redox kinetic in silicate melt; Etude cinetique des reactions d'oxydoreduction dans les silicates

    Energy Technology Data Exchange (ETDEWEB)

    Magnien, V

    2005-12-15

    The aim of this thesis is to understand better iron redox reactions and mechanisms in silicate glasses and melts. Particular interest has been paid to the influence of temperature and chemical composition. For this purpose, the influence of alkali element content, iron content and network formers on the kinetics of redox reactions has been determined through XANES and Raman spectroscopy experiments performed either near the glass transition or above the liquidus temperature. As a complement, electrical conductivity and RBS spectroscopy experiments have been made to characterize the diffusivity of the species that transport electrical charges and the reaction morphology, respectively. Temperature and composition variations can induce changes in the dominating redox mechanism. At a given temperature, the parameters that exert the strongest influence on redox mechanisms are the presence or lack of divalent cations and the existing decoupling between the mobility of network former and modifier elements. Near Tg, the diffusion of divalent cations, when present in the melt, controls the kinetics of iron redox reactions along with a flux of electron holes. Composition, through the degree of polymerization and the silicate network structure, influences the kinetics and the nature of the involved cations, but not the mechanisms of the reaction. Without alkaline earth elements, the kinetics of redox reactions are controlled by the diffusion of oxygen species. With increasing temperatures, the diffusivities of all ionic species tend to become similar. The decoupling between ionic fluxes then is reduced so that several mechanisms become kinetically equivalent and can thus coexist. (author)

  8. EXAMINATION OF SILICATE LIMITATION OF PRIMARY PRODUCTION IN JIAOZHOU BAY, CHINA Ⅰ. SILICATE BEING A LIMITING FACTOR OF PHYTOPLANKTON PRIMARY PRODUCTION

    Institute of Scientific and Technical Information of China (English)

    杨东方; 张经; 吕吉斌; 高振会; 陈豫

    2002-01-01

    Jiaozhou Bay data collected from May 1991 to February 1994, in 12 seasonal investigations, and provided the authors by the Ecological Station of Jiaozhou B ay, were analyzed to determine the spatiotemporal variations in temperature, light, nutrients (NO-3-N, NO-2-N, NH+4-N, SiO2-3-Si, PO3-4-P), phytoplankton, and primary production in Jiaozhou Bay. The results indicated that only silicate correlated well in time and space with, and had important effects on, the characteristics, dynamic cycles and trends of, primary production in Jiaozhou Bay. The authors developed a corresponding dynamic model of primary production and silicate and water temperature. Eq.(1) of the model shows that the primary production variation is controlled by the nutrient Si and affected by water temp erature; that the main factor controlling the primary production is Si; that water temper ature affects the composition of the structure of phytoplankton assemblage; that the different populations of the phytoplankton assemblage occupy different ecologica l niches for C, the apparent ratio of conversion of silicate in seawater into phytoplankton biomas and D, the coefficient of water temperature's effect on phytoplankton biomass. The authors researched the silicon source of Jiaozhou Bay , the biogeochemical sediment process of the silicon, the phytoplankton predominan t species and the phytoplankton structure. The authors considered silicate a limit ing factor of primary production in Jiaozhou Bay, whose decreasing concentration of silicate from terrestrial source is supposedly due to dilution by current and up take by phytoplankton; quantified the silicate assimilated by phytoplankton, the intrins ic ratio of conversion of silicon into phytoplankton biomass, the proportion of silicate uptaken by phytoplankton and diluted by current; and found that the primary production of the phytoplankton is determined by the quantity of the silicate assimilated by them. The phenomenon of apparently high plant

  9. EXAMINATION OF SILICATE LIMITATION OF PRIMARY PRODUCTION IN JIAOZHOU BAY, CHINA——I. SILICATE BEING A LIMITING FACTOR OF PHYTOPLANKTON PRIMARY PRODUCTION

    Institute of Scientific and Technical Information of China (English)

    杨东方; 张经; 吕吉斌; 高振会; 陈豫

    2002-01-01

    Jiaozhou Bay data collected from May 1991 to February 1994, in 12 seasonal investigations, and provided the authors by the Ecological Station of Jiaozhou Bay, were analyzed to determine the spatiotemporal variations in temperature, light, nutrients (NO3--N, NO2--N, NH4+-N, SIO32--Si, PO43--P), phytoplankton, and primary production in Jiaozhou Bay. The results indicated that only silicate correlated well in time and space with, and had important effects on, the characteristics, dynamic cycles and trends of, primary production in Jiaozhou Bay. The authors developed a corresponding dynamic model of primary production and silicate and water temperature. Eq. ( 1 ) of the model shows that the primary production variation is controlled by the nutrient Si and affected by water temperature; that the main factor controlling the primary production is Si; that water temperature affects the composition of the structure of phytoplankton assemblage; that the different populations of the phytoplankton assemblage occupy different ecological niches for C, the apparent ratio of conversion of silicate in seawater into phytoplankton biomas and D, the coefficient of water temperature's effect on phytoplankton biomass. The authors researched the silicon source of Jiaozhou Bay, the biogeochemical sediment process of the silicon, the phytoplankton predominant species and the phytoplankton structure. The authors considered silicate a limiting factor of primary production in Jiaozhou Bay, whose decreasing concentration of silicate from terrestrial source is supposedly due to dilution by current and uptake by phytoplankton; quantified the silicate assimilated by phytoplankton, the intrinsic ratio of conversion of silicon into phytoplankton biomass, the proportion of silicate uptaken by phytoplankton and diluted by current; and found that the primary production of the phytoplankton is determined by the quantity of the silicate assimilated by them. The phenomenon of apparently high plant

  10. GO@CuSilicate nano-needle arrays hierarchical structure: a new route to prepare high optical transparent, excellent self-cleaning and anticorrosion superhydrophobic surface

    Science.gov (United States)

    Fan, Ping; Chen, Jingyi; Yang, Jintao; Chen, Feng; Zhong, Mingqiang

    2017-02-01

    Transparent superhydrophobic coatings, which are highly desired for the protection of material surfaces, have been limited to particular kinds of materials, e.g. silicon dioxide. In this work, a hybrid compound of graphene oxide and copper silicate with hierarchical structure was developed and was used to fabricate coatings. Due to the high transparency of graphene oxide and the nanoscopic roughness created by nanoneedles of CuSilicate, with very low compound loading (0.052 mg/cm2), the as-prepared coating was found not only showing superhydrophobic properties with a water contact angle (CA) of ˜152° and a near zero sliding angle (SA) of 0.5 but also showing high optical transparent (light transmittance is as high as 94.5 % at 500 nm). Furthermore, this surface also showed efficient anticorrosion properties and excellent self-cleaning ability. This study not only fabricated a new surface with transparency and surperhydrophobicity based on graphene materials, but also hopefully offers a method for the fabrication of multifunctional coatings.

  11. FT-IR and 29 Si-NMR for evaluating aluminium silicate precursors for geopolymers

    NARCIS (Netherlands)

    Valcke, S.L.A.; Pipilikaki, P.; Fischer, H.R.; Verkuijlen, M.H.W.; Eck, E.R.H.

    2014-01-01

    Geopolymers are systems of inorganic binders that can be used for sustainable, cementless concrete and are formed by alkali activation of an aluminium–silicate precursor (often secondary resources like fly ash or slag). The type of aluminium– silicate precursor and its potential variations within on

  12. Effect of silicate pretreatment, post-sealing and additives on corrosion resistance of phosphated galvanized steel

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Sodium silicate (water glass) pretreatment before phosphating, silicate post-sealing after phosphating and adding silicate to a traditional phosphating solution were respectively carried out to obtain the improved phosphate coatings with high corrosion resistance and coverage on hot-dip galvanized(HDG) steel. The corrosion resistance, morphology and chemical composition of the coatings were investigated using neutral salt spray(NSS) tests, scanning electron microscopy(SEM) and energy dispersive spectroscopy(EDS). The results show that pretreatment HDG steel with silicate solutions, phosphate coatings with finer crystals and higher coverage are formed and the corrosion resistance is enhanced. Adding silicate to a traditional phosphating solution, the surface morphology of the coatings is nearly unchanged. The corrosion resistance of the coatings is mainly dependent on phosphating time.Phosphating for a longer time (such as 5 min), the corrosion resistance, increasing with concentration of silicate, is improved significantly. Post-sealing the phosphated HDG steel with silicate solutions, the pores among the zinc phosphate crystals are sealed with the films containing Si, P, O and Zn and the continuous composite coatings are formed. The corrosion resistance of the composite coatings, related to the pH value, contents of hydrated gel of silica and Si2O52- and post-sealing time, is increased markedly. The improved coatings with optimal corrosion resistance are obtained for phosphating 5 min and post-sealing with 5 g/L silicate solution for 10 min.

  13. Synthesis and reaction behavior of calcium silicate hydrate in basic system

    Institute of Scientific and Technical Information of China (English)

    刘桂华; 贺强; 李小斌; 彭志宏; 周秋生

    2004-01-01

    At the molar ratio of CaO to SiO2 of 1, with calcium hydroxide and sodium silicate, calcium silicate hydrate was synthesized at 50, 100, 170 ℃, respectively. The results show that temperature favors the formation of calcium silicate hydrate with perfect structure. When calcium silicate hydrate reacts with caustic solution, the decomposition rate of calcium silicate hydrate increases with the increasing caustic concentration and decreases with the raising synthesis temperature and the prolongation of reaction time. The decomposition rate is all less than 1.2 % in caustic solution, and XRD pattern of the residue after reaction with caustic solution is found as the same as that of original calcium silicate hydrate, which indicates the stable existence of calcium silicate hydrate in caustic solution.When reacted with soda solution, the decomposition rate increases with the increasing soda concentration and reaction time, while decreases with the synthesis temperature. The decomposition rate is more than 2% because CaO · SiO2 · H2O(CSH( Ⅰ )), except Ca5 (OH)2Si6O16 · 4H2O and Ca6Si6O17 (OH)2, is decomposed. So the synthesis temperature and soda concentration should be controlled in the process of transformation of sodium aluminosilicate hydrate into calcium silicate hydrate.

  14. A hidden reservoir of Fe/FeS in interstellar silicates?

    CERN Document Server

    Köhler, M; Ysard, N

    2014-01-01

    The depletion of iron and sulphur into dust in the interstellar medium and the exact nature of interstellar amorphous silicate grains is still an open question. We study the incorporation of iron and sulphur into amorphous silicates of olivine- and pyroxene-type and their effects on the dust spectroscopy and thermal emission. We used the Maxwell-Garnett effective-medium theory to construct the optical constants for a mixture of silicates, metallic iron, and iron sulphide. We also studied the effects of iron and iron sulphide in aggregate grains. Iron sulphide inclusions within amorphous silicates that contain iron metal inclusions shows no strong differences in the optical properties of the grains. A mix of amorphous olivine- and pyroxene-type silicate broadens the silicate features. An amorphous carbon mantle with a thickness of 10 nm on the silicate grains leads to an increase in absorption on the short-wavelength side of the 10 $\\mu$m silicate band. The assumption of amorphous olivine-type and pyroxene-typ...

  15. Crystal Structure and Chemical Composition of a Presolar Silicate from the Queen Elizabeth Range 99177 Meteorite

    Science.gov (United States)

    Nguyen, A. N.; Keller, L. P.; Rahman, Z.; Messenger, S.

    2013-01-01

    Mineral characterization of presolar silicate grains, the most abundant stardust phase, has provided valuable information about the formation conditions in circumstellar environments and in super-nova (SN) outflows. Spectroscopic observations of dust around evolved stars suggest a majority of amor-phous, Mg-rich olivine grains, but crystalline silicates, most of which are pyroxene, have also been observed [1]. The chemical compositions of hundreds of presolar silicates have been determined by Auger spectroscopy and reveal high Fe contents and nonstoichiometric compositions intermediate to olivine and pyroxene [2-6]. The unexpectedly high Fe contents can partly be attributed to secondary alteration on the meteorite parent bodies, as some grains have Fe isotopic anomalies from their parent stellar source [7]. Only about 35 presolar silicates have been studied for their mineral structures and chemical compositions by transmission electron microscopy (TEM). These grains display a wide range of compositions and structures, including crystalline forsterite, crystalline pyroxene, nanocrystalline grains, and a majority of amorphous nonstoichiometric grains. Most of these grains were identified in the primitive Acfer 094 meteorite. Presolar silicates from this meteorite show a wide range of Fe-contents, suggestive of secondary processing on the meteorite parent body. The CR chondrite QUE 99177 has not suffered as much alteration [8] and displays the highest presolar silicate abundance to date among carbonaceous chondrites [3, 6]. However, no mineralogical studies of presolar silicates from this meteorite have been performed. Here we examine the mineralogy of a presolar silicate from QUE 99177.

  16. Molecular Dynamics Modeling of Hydrated Calcium-Silicate-Hydrate (CSH) Cement Molecular Structure

    Science.gov (United States)

    2014-08-30

    properties of key hydrated cement constituent calcium-silicate-hydrate (CSH) at the molecular, nanometer scale level. Due to complexity, still unknown...public release; distribution is unlimited. Molecular Dynamics Modeling of Hydrated Calcium-Silicate- Hydrate (CSH) Cement Molecular Structure The views... Cement Molecular Structure Report Title Multi-scale modeling of complex material systems requires starting from fundamental building blocks to

  17. Mechanical and thermal properties of sodium silicate treated moso bamboo particles reinforced PVC composites

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The main objective of this research was to study the potential of sodium silicate modification on moso bamboo particles as reinforcements for thermoplastic. Moso bamboo particles were modified with sodium silicate aqueous solutions (of 0.5%, 1%, 2%, 5% and 10% concentrations). The mechanical properties of sodium silicate treated moso bamboo particles reinforced PVC composites (BPPC) were calculated and compared with raw bamboo particles filled samples. The thermal characteristics of the BPPC were studied to investigate the feasibility of sodium silicate treatment on moso bamboo particles. The particle morphology and BPPC microstructure were investigated by scanning electron microscopy. Results showed that the tensile strength and modulus of elasticity of the BPPC increased before the concentration of sodium silicate solution reached 5% and got their maximum values of 15.72 MPa and 2956.80 MPa, respectively at 5% concentration. The modulus of rupture obtained the maximum value of 27.73 MPa at 2% concentration. The mechanical curve decreased as the concentration of solution went higher. Differential scanning calorimetric analysis illustrated that the sodium silicate solution treated BPPC possesses a better compatibility. More uniform dispersion of moso bamboo particles in PVC matrix was obtained after the sodium silicate treatment. Hence, the sodium silicate was a feasible and competitive agent of creating moso bamboo particles reinforced PVC composites.

  18. Synthesis of magnesium silicate from wheat husk ash: Effects of parameters on structural and surface properties

    Directory of Open Access Journals (Sweden)

    Pinar Terzioglu

    2012-11-01

    Full Text Available In the present study, magnesium silicate was produced by using wheat husk ash. Wheat husk was burned at 600 °C to obtain an amorphous ash structure, and the ash was processed with sodium hydroxide solution with heat to extract silica. Sodium silicate solution and magnesium salts were used to synthesize magnesium silicate. The present study investigates effects of the feeding rate on magnesium silicate production (0.6 mL/min, 35 mL/min, 70 mL/min, the type of magnesium salt (MgSO4 • 7H2O or MgCl2 • 6H2O, temperature (25 °C or 50 °C, and the washing agent (water and acetone on the chemical composition and surface characteristics of magnesium silicate. The results demonstrated that all of the variables affected the surface characteristics of magnesium silicate, such as surface area, particle size, and pore volume. However, it was also observed that the studied parameters did not affect the chemical composition of magnesium silicate. The wheat husk ash-based magnesium silicates obtained in the experimental study had a BET surface area ranging from 79 to 91 m2/g and a particle size varying from 42 to 63 µm.

  19. Microstructure engineering of Portland cement pastes and mortars through addition of ultrafine layer silicates

    DEFF Research Database (Denmark)

    Lindgreen, Holger; Geiker, Mette; Krøyer, Hanne;

    2008-01-01

    Pozzolanic submicron-sized silica fume and the non-pozzolanic micron- and nano-sized layer silicates (clay minerals) kaolinite, smectite and palygorskite have been used as additives in Portland cement pastes and mortars. These layer silicates have different particle shape (needles and plates), su...

  20. Optical Properties of Astronomical Silicates with Infrared Techniques (OPASI-T)

    Science.gov (United States)

    Rinehart, Stephen

    2010-01-01

    Astronomical dust is observed in a variety of astrophysical environments and plays an important role in radiative processes and chemical evolution in the galaxy. Depending upon the environment, dust can be either carbon-rich or oxygen-rich (silicate grains). Both astronomical observations and ground-based data show that the optical properties of silicates can change dramatically with the crystallinity of the material, and recent laboratory research provides evidence that the optical properties of silicate dust vary as a function of temperature as well. Therefore, correct interpretation of a vast array of astronomical data relies on the understanding of the properties of silicate dust as functions of wavelength, temperature, and crystallinity. The OPASI-T (Optical Properties of Astronomical Silicates with Infrared Techniques) project addresses the need for high quality optical characterization of metal-enriched silicate condensates using a variety of techniques. A combination of both new and established experiments are used to measure the extinction, reflection, and emission properties of amorphous silicates across the infrared (near infrared to millimeter wavelengths), providing a comprehensive data set characterizing the optical parameters of dust samples. We present room temperature measurements and the experimental apparatus to be used to investigate and characterize additional metal-silicate materials.

  1. Nanoparticles Containing High Loads of Paclitaxel-Silicate Prodrugs: Formulation, Drug Release, and Anticancer Efficacy.

    Science.gov (United States)

    Han, Jing; Michel, Andrew R; Lee, Han Seung; Kalscheuer, Stephen; Wohl, Adam; Hoye, Thomas R; McCormick, Alon V; Panyam, Jayanth; Macosko, Christopher W

    2015-12-07

    We have investigated particle size, interior structure, drug release kinetics, and anticancer efficacy of PEG-b-PLGA-based nanoparticles loaded with a series of paclitaxel (PTX)-silicate prodrugs [PTX-Si(OR)3]. Silicate derivatization enabled us to adjust the hydrophobicity and hydrolytic lability of the prodrugs by the choice of the alkyl group (R) in the silicate derivatives. The greater hydrophobicity of these prodrugs allows for the preparation of nanoparticles that are stable in aqueous dispersion even when loaded with up to ca. 75 wt % of the prodrug. The hydrolytic lability of silicates allows for facile conversion of prodrugs back to the parent drug, PTX. A suite of eight PTX-silicate prodrugs was investigated; nanoparticles were made by flash nanoprecipitation (FNP) using a confined impingement jet mixer with a dilution step (CIJ-D). The resulting nanoparticles were 80-150 nm in size with a loading level of 47-74 wt % (wt %) of a PTX-silicate, which corresponds to 36-59 effective wt % of free PTX. Cryogenic transmission electron microscopy images show that particles are typically spherical with a core-shell structure. Prodrug/drug release profiles were measured. Release tended to be slower for prodrugs having greater hydrophobicity and slower hydrolysis rate. Nanoparticles loaded with PTX-silicate prodrugs that hydrolyze most rapidly showed in vitro cytotoxicity similar to that of the parent PTX. Nanoparticles loaded with more labile silicates also tended to show greater in vivo efficacy.

  2. Sodium Silicate Behavior in Porous Media Applied for In-Depth Profile Modifications

    Directory of Open Access Journals (Sweden)

    Hossein A. Akhlaghi Amiri

    2014-03-01

    Full Text Available This paper addresses alkaline sodium silicate (Na-silicate behavior in porous media. One of the advantages of the Na-silicate system is its water-like injectivity during the placement stage. Mixing Na-silicate with saline water results in metal silicate precipitation as well as immediate gelation. This work demonstrated that low salinity water (LSW, sea water diluted 25 times could be used as a pre-flush in flooding operations. A water override phenomenon was observed during gel formation which is caused by gravity segregation. Dynamic adsorption tests in the sand-packed tubes showed inconsiderable adsorbed silicon density (about 8.5 × 10−10 kg/cm3 for a solution with 33 mg/L silicon content, which is less than the estimated mono-layer adsorption density of 1.4 × 10−8 kg/cm3. Na-silicate enhanced water sweep efficiency after application in a dual-permeability sand-pack system, without leak off into the oil-bearing low permeability (LP zone. Field-scale numerical sensitivity studies in a layered reservoir demonstrated that higher permeability and viscosity contrasts and lower vertical/horizontal permeability ratio result in lower Na-silicate leakoff into the matrix. The length of the mixing zone between reservoir water and the injected Na-silicate solution, which is formed by low salinity pre-flush, acts as a buffer zone.

  3. Use of copper radioisotopes in investigating disorders of copper metabolism

    Energy Technology Data Exchange (ETDEWEB)

    Camakaris, J.; Voskoboinik, I.; Brooks, H.; Greenough, M. [University of Melbourne, Parkville, VIC (Australia). Department of Genetics; Smith, S. [Australian Nuclear Science and Technology Organisation (ANSTO), Lucas Heights, NSW (Australia). Radiopharmaceuticals Division; Mercer, J. [Deakin University, Rusden Campus, Clayton, VIC (Australia). Centre of Cellular and Molecular Biology

    1998-12-31

    Full text: Copper is an essential trace element for life as a number of vital enzymes require it. Copper deficiency can lead to neurological disorders, osteoporosis and weakening of arteries. However Cu is also highly toxic and homeostatic mechanisms have evolved to maintain Cu at levels which satisfy requirements but do not cause toxicity. Toxicity is mediated by the oxidative capacity of Cu and its ability to generate toxic free radicals. There are several acquired and inherited diseases due to either Cu toxicity or Cu deficiency. The study of these diseases facilitates identification of genes and proteins involved in copper homeostasis, and this in turn will provide rational therapeutic approaches. Our studies have focused on Menkes disease in humans which is an inherited and usually lethal copper deficiency. Using copper radioisotopes {sup 64}Cu (t 1/2 = 12.8 hr) and {sup 67}Cu (t 1/2 = 61 hr) we have studied the protein which is mutated in Menkes disease. This is a transmembrane copper pump which is responsible for absorption of copper into the body and also functions to pump out excess Cu from cells when Cu is elevated. It is therefore a vital component of normal Cu homeostasis. We have provided the first biochemical evidence that the Menkes protein functions as a P-type ATPase Cu pump (Voskoboinik et al., FEBS Letters, in press) and these data will be discussed. The assay involved pumping of radiocopper into purified membrane vesicles. Furthermore we have transfected normal and mutant Menkes genes into cells and are carrying out structure-function studies. We are also studying the role of amyloid precursor protein (APP) as a Cu transport protein in order to determine how Cu regulates this protein and its cleavage products. These studies will provide vital information on the relationship between Cu and APP and processes which lead to Alzheimers disease

  4. LUMINESCENT PROPERTIES OF SILICATE GLASSES WITH CERIUM IONS AND ANTIMONY

    Directory of Open Access Journals (Sweden)

    A. M. Klykova

    2014-05-01

    Full Text Available The paper deals with the results of an experimental study of luminescence excitation spectra and luminescence of silicate glasses containing cerium ions and antimony. The aim of this work was to study the features of the luminescence and the effect of UV irradiation and heat treatment on luminescence and the state of cerium ions and antimony in glass. We investigated glass system Na2O-ZnO-Al2O3-SiO2-NaF-NaBr with additives CeO2 and Sb2O3. Synthesis was carried out in platinum crucibles in the air at 14500C. The samples were polished glass plates with a thickness of 0.5-1 mm. UV irradiation was carried out with a mercury lamp having a wide range of radiation in the spectral range 240-390 nm. It was conducted in a Nabertherm muffle furnaces. Luminescence spectra and excitation spectra were measured using a spectrofluorimeter MPF-44A (PerkinElmer at the room temperature. Measured luminescence spectra were corrected in view of the spectral sensitivity of the photodetector for spectrofluorimeter. Adjustment of the excitation spectra for the spectral dependence of the intensity of the excitation source was not carried out. During the experiments it was found that in silicate glasses Sb3+ ions can exist in two energy states, which corresponds to a different environment with oxygen ions. Heat treatment of these glasses in an oxidizing atmosphere leads to an increase in ion concentration of Sb3+ ions with a greater amount of oxygen in the environment. In glasses containing antimony and cerium ions, ultraviolet irradiation causes a change in the valence of cerium ions and antimony, which is accompanied by luminescence quenching. Subsequent heat treatment of glass leads to the inverse processes and restore luminescence excitation spectra. The study of fluorescent properties of silicate glasses with cerium and antimony ions led to the conclusion of the practical significance of this work. Promising multifunctional materials can be created on the basis of

  5. Dynamic Strengthening During High Velocity Shear Experiments with Siliceous Rocks

    Science.gov (United States)

    Liao, Z.; Chang, J. C.; Boneh, Y.; Chen, X.; Reches, Z.

    2011-12-01

    It is generally accepted that dynamic-weakening is essential for earthquake instability, and many experimental works have documented this weakening. Recent observations revealed also opposite trends of dynamic-strengthening in experiments (Reches & Lockner, 2010). We present here our experimental results of this dynamic-strengthening and discuss possible implications to earthquake behavior. We ran hundreds of experiments on experimental faults made of siliceous rock including granite, syenite, diorite, and quartzite. The experimental fault is comprised of two solid cylindrical blocks with a raised-ring contact of 7 cm diameter and 1 cm width. We recognized general, three regimes of strength-velocity relations: (I) Dynamic weakening (drop of 20-60% of static strength) as slip velocity increased from ~0.0003 m/s (lowest experimental velocity) to a critical velocity, Vc=0.008-0.16 m/s; (II) Abrupt transition to dynamic strengthening regime during which the fault strength almost regains its static strength; and (III) Quasi-constant strength with further possible drops as velocity approaches ~1 m/s. The critical velocity depends on the sample lithology: Vc is ~0.06 m/s for granite, ~0.008 m/s for syenite, ~0.01 m/s for diorite, and ~0.16 m/s for quartzite. The strengthening stage is associated with temperature increase, wear-rate increase, and the occurrence of intense, high frequency stick-slip events (Reches & Lockner, 2010). Sammis et al., (this meeting) attributed this strengthening to dehydration of the thin water layer that covers the gouge particles as the temperature increases. On the other hand, we note that tens of experiments with dolomite samples (non-siliceous), which were deformed under similar conditions, did not exhibit the velocity strengthening (unpublished). Based on the analyses by Andrews (2004, 2005), we speculate that velocity strengthening may bound the slip velocity. The numerical models of Andrews show that the slip velocity along a slip

  6. Bioactivity studies of calcium magnesium silicate prepared from eggshell waste by sol–gel combustion synthesis

    Directory of Open Access Journals (Sweden)

    Rajan Choudhary

    2015-06-01

    Full Text Available The present study focused on the synthesis of calcium magnesium silicate (akermanite, Ca2MgSi2O7 using eggshell biowaste (as calcium source, magnesium nitrate and tetraethyl orthosilicate (TEOS as starting materials. Sol–gel combustion method was adopted to obtain calcium magnesium silicate. Citric acid was used as a fuel (reducing agent and nitrate ions present in the metal nitrates acts as an oxidizing agent during combustion process. The characterization of synthesized calcium magnesium silicate was carried out by powder X-ray diffraction (XRD, Fourier transform infrared (FTIR and scanning electron microscopy (SEM techniques. Calcium magnesium silicate crystallite size was observed in nano regime which can effectively mimic natural bone apatite composition. In-vitro bioactivity was investigated by immersing calcium magnesium silicate pellet in simulated body fluid (SBF for three weeks. Results show effective deposition of crystallized hydroxyapatite (HAP layer on its surface and predicting its possibilities for applications in hard tissue regeneration.

  7. Pilot study on binding of bovine salivary proteins to grit silicates and plant phytoliths.

    Science.gov (United States)

    Mau, Marcus; M Kaiser, Thomas; Südekum, Karl-Heinz

    2013-06-01

    Mostly fed with grass in fresh or conserved form, cattle and other livestock have to cope with silicate defence bodies from plants (phytoliths) and environmental silicates (grit), which abrade tooth enamel and could additionally interact with various salivary proteins. To detect potential candidates for silicate-binding proteins, bovine whole saliva was incubated with grass-derived phytoliths and silicates. Interactions of salivary proteins with pulverized bovine dental enamel and dentine were additionally analysed. After intense washing, the powder fractions were loaded onto 1D-polyacrylamide gels, most prominent adhesive protein bands were cut out and proteins were identified by mass spectrometry within three independent replicates. All materials were mainly bound by bovine odorant-binding protein, bovine salivary protein 30×10(3) and carbonic anhydrase VI. The phytolith/silicate fraction showed additional stronger interaction with haemoglobin β and lactoperoxidase. Conceivably, the binding of these proteins to the surfaces may contribute to biological processes occurring on them.

  8. Soft X-Ray Irradiation of Silicates: Implications for Dust Evolution in Protoplanetary Disks

    Science.gov (United States)

    Ciaravella, A.; Cecchi-Pestellini, C.; Chen, Y.-J.; Muñoz Caro, G. M.; Huang, C.-H.; Jiménez-Escobar, A.; Venezia, A. M.

    2016-09-01

    The processing of energetic photons on bare silicate grains was simulated experimentally on silicate films submitted to soft X-rays of energies up to 1.25 keV. The silicate material was prepared by means of a microwave assisted sol-gel technique. Its chemical composition reflects the Mg2SiO4 stoichiometry with residual impurities due to the synthesis method. The experiments were performed using the spherical grating monochromator beamline at the National Synchrotron Radiation Research Center in Taiwan. We found that soft X-ray irradiation induces structural changes that can be interpreted as an amorphization of the processed silicate material. The present results may have relevant implications in the evolution of silicate materials in X-ray-irradiated protoplanetary disks.

  9. Newly Identified Silicate Carbon Stars from IRAS Low-Resolution Spectra

    Institute of Scientific and Technical Information of China (English)

    Pei-Sheng Chen; Pin Zhang

    2006-01-01

    The discovery of silicate carbon star poses a challenge to the theory of stellar evolution in the late stage, hence it is important to look for more silicate carbon stars. To this end we have carried out cross-identifications between the new IRAS Low-Resolution Spectrum (LRS) database and the new carbon star catalog, CGCS3. We have found nine new silicate carbon stars with silicate features around 10μm and/or 18 μm. These newly identified stars are located in the Regions Ⅲa and Ⅶ in the IRAS two-color diagram, which means they indeed have typical far infrared colors of silicate carbon stars. The infrared properties of each of these sources are discussed.

  10. Identification of an Extremely 180-Rich Presolar Silicate Grain in Acfer 094

    Science.gov (United States)

    Nguyen, A. N.; Messenger, S.

    2009-01-01

    Presolar silicate grains have been abundantly identified since their first discovery less than a decade ago [1,2,3]. The O isotopic compositions of both silicate and oxide stardust indicate the vast majority (>90%) condensed around Orich asymptotic giant branch (AGB) stars. Though both presolar phases have average sizes of 300 nm, grains larger than 1 m are extremely uncommon for presolar silicates. Thus, while numerous isotopic systems have been measured in presolar oxide grains [4], very few isotopic analyses for presolar silicates exist outside of O and Si [2,5]. And still, these measurements suffer from isotopic dilution with surrounding matrix material [6]. We conduct a search for presolar silicates in the primitive carbonaceous chondrite Acfer 094 and in some cases obtain high spatial resolution, high precision isotopic ratios.

  11. Soft X-ray Irradiation of Silicates: Implications on Dust Evolution in Protoplanetary Disks

    CERN Document Server

    Ciaravella, A; Chen, Y -J; Caro, G M Muñoz; Huang, C -H; Jiménez-Escobar, A; Venezia, A M

    2016-01-01

    The processing of energetic photons on bare silicate grains was simulated experimentally on silicate ?lms submitted to soft X-rays of energies up to 1.25 keV. The silicate material was prepared by means of a microwave assisted solgel technique. Its chemical composition reflects the Mg2SiO4 stoichiometry with residual impurities due to the synthesis method. The experiments were performed using the spherical grating monochromator beamline at the National Synchrotron Radiation Research Center in Taiwan. We found that soft X-ray irradiation induces structural changes that can be interpreted as an amorphization of the processed silicate material. The present results may have relevant implications in the evolution of silicate materials in X-ray irradiated protoplanetary disks.

  12. Improving Beneficiation of Copper and Iron from Copper Slag by Modifying the Molten Copper Slag

    Directory of Open Access Journals (Sweden)

    Zhengqi Guo

    2016-04-01

    Full Text Available In the paper, a new technology was developed to improve the beneficiation of copper and iron components from copper slag, by modifying the molten slag to promote the mineralization of valuable minerals and to induce the growth of mineral grains. Various parameters, including binary basicity, dosage of compound additive, modification temperature, cooling rate and the end point temperature of slow cooling were investigated. Meanwhile, optical microscope, scanning electron microscope and energy dispersive spectrometer (SEM-EDS was employed to determine the mineralogy of the modified and unmodified slag, as well as to reveal the mechanisms of enhancing beneficiation. The results show that under the proper conditions, the copper grade of rougher copper concentrate was increased from 6.43% to 11.04%, iron recovery of magnetic separation was increased significantly from 32.40% to 63.26%, and other evaluation indexes were changed slightly, in comparison with unmodified copper slag. Moreover, matte and magnetite grains in the modified slag aggregated together and grew obviously to the mean size of over 50 μm, resulting in an improvement of beneficiation of copper and iron.

  13. The Reaction of Carbonates in Contact with Superheated Silicate Melts: New Insights from MEMIN Laser Melting Experiments

    Science.gov (United States)

    Hamann, C.; Hecht, L.; Schäffer, S.; Deutsch, A.; Lexow, B.

    2016-08-01

    The reaction of carbonates in contact with silicate impact melts is discussed quite controversially in the impact community. Here, we discuss four MEMIN laser melting experiments involving carbonates in contact with superheated silicate melts.

  14. TECHNOLOGY EVALUATION REPORT: SILICATE TECHNOLOGY CORPORATION - SOLIDIFICATION/STABILIZATION OF PCP AND INORGANIC CONTAMINANTS IN SOILS - SELMA, CA

    Science.gov (United States)

    This Technolgy Evaluation Report evaluates the solidification/stabilization process of Silicate Technology Corporation (STC) for the on-site treatment of contaminated soil The STC immobilization technology uses a proprietary product (FMS Silicate) to chemically stabilize and ...

  15. Role of organically modified layered silicate both as an active interfacial modifier and nanofiller for immiscible polymer blends.

    CSIR Research Space (South Africa)

    Ray, SS

    2007-05-01

    Full Text Available ) revealed efficient mixing of the polymers in the presence of organically modified layered silicate. X-ray diffraction (XRD) patterns and transmission electron microscopic (TEM) observations showed that silicate layers were either intercalated or exfoliated...

  16. Renal cortex copper concentration in acute copper poisoning in calves

    Directory of Open Access Journals (Sweden)

    Luis E. Fazzio

    2012-01-01

    Full Text Available The aim of this study was to estimate the diagnostic value of renal cortex copper (Cu concentration in clinical cases of acute copper poisoning (ACP. A total of 97 calves that died due to subcutaneous copper administration were compiled in eleven farms. At least, one necropsy was conducted on each farm and samples for complementary analysis were taken. The degree of autolysis in each necropsy was evaluated. The cases appeared on extensive grazing calf breeding and intensive feedlot farms, in calves of 60 to 200 kg body weight. Mortality varied from 0.86 to 6.96 %, on the farms studied. The first succumbed calf was found on the farms between 6 and 72 hours after the susbcutaneous Cu administration. As discrepancies regarding the reference value arose, the local value (19.9 parts per million was used, confirming the diagnosis of acute copper poisoning in 93% of the analyzed kidney samples. These results confirm the value of analysis of the cortical kidney Cu concentration for the diagnosis of acute copper poisoning.

  17. Effects of Silicate, Phosphate, and Calcium on the Stability of Aldopentoses.

    Science.gov (United States)

    Nitta, Sakiko; Furukawa, Yoshihiro; Kakegawa, Takeshi

    2016-06-01

    Ribose is an important constituent of RNA: ribose connects RNA bases and forms a strand of sugar phosphates. Accumulation of ribose on prebiotic Earth was difficult because of its low stability. Improvement in the yield of ribose by the introduction of borate or silicate in a formose-like reaction has been proposed. The effects of borates have been further analyzed and confirmed in subsequent studies. Nonetheless, the effects of silicates and phosphates remain unclear. In the present study, we incubated aldopentoses in a highly alkaline aqueous solution at a moderate temperature to determine the effects of silicate or phosphate on the degradation rates of ribose and its isomeric aldopentoses. The formation of a complex of silicate (or phosphate) with ribose was also analyzed in experiments with (29)Si and (31)P nuclear magnetic resonance (NMR). We found that silicate or phosphate complexes of ribose were not detectable under our experimental conditions. The stability of ribose and lyxose improved after addition of 40-fold molar excess (relative to a pentose) of sodium silicate or sodium phosphate to the alkaline solution. The stability was not improved further when an 80-fold molar excess of sodium silicate or sodium phosphate was added. Calcium was removed from these solutions by precipitation of calcium salts. The drop in Ca(2+) concentration might have improved the stability of ribose and lyxose, which are susceptible to aldol addition. The improvement of ribose stability by the removal of Ca(2+) and by addition of silicate or phosphate was far smaller than the improvement by borate. Furthermore, all aldopentoses showed similar stability in silicate- and phosphate-containing solutions. These results clearly show that selective stabilization of ribose by borate cannot be replaced by the effects of silicate or phosphate; this finding points to the importance of borate in prebiotic RNA formation.

  18. Measurement of the efficacy of calcium silicate for the protection and repair of dental enamel.

    Science.gov (United States)

    Parker, Alexander S; Patel, Anisha N; Al Botros, Rehab; Snowden, Michael E; McKelvey, Kim; Unwin, Patrick R; Ashcroft, Alexander T; Carvell, Mel; Joiner, Andrew; Peruffo, Massimo

    2014-06-01

    To investigate the formation of hydroxyapatite (HAP) from calcium silicate and the deposition of calcium silicate onto sound and acid eroded enamel surfaces in order to investigate its repair and protective properties. Calcium silicate was mixed with phosphate buffer for seven days and the resulting solids analysed for crystalline phases by Raman spectroscopy. Deposition studies were conducted on bovine enamel surfaces. Acid etched regions were produced on the enamel surfaces using scanning electrochemical cell microscopy (SECCM) with acid filled pipettes and varying contact times. Following treatment with calcium silicate, the deposition was visualised with FE-SEM and etch pit volumes were measured by AFM. A second set of bovine enamel specimens were pre-treated with calcium silicate and fluoride, before acid exposure with the SECCM. The volumes of the resultant acid etched pits were measured using AFM and the intrinsic rate constant for calcium loss was calculated. Raman spectroscopy confirmed that HAP was formed from calcium silicate. Deposition studies demonstrated greater delivery of calcium silicate to acid eroded than sound enamel and that the volume of acid etched enamel pits was significantly reduced following one treatment (penamel was 0.092 ± 0.008 cm/s. This was significantly reduced, 0.056 ± 0.005 cm/s, for the calcium silicate treatments (penamel surfaces. Calcium silicate can provide significant protection of sound enamel from acid challenges. Calcium silicate is a material that has potential for a new approach to the repair of demineralised enamel and the protection of enamel from acid attacks, leading to significant dental hard tissue benefits. © 2014 Elsevier Ltd. All rights reserved.

  19. Vibrational spectroscopic study of the copper silicate mineral kinoite Ca2Cu2Si3O10(OH)4.

    Science.gov (United States)

    Frost, Ray L; Xi, Yunfei

    2012-04-01

    Kinoite Ca2Cu2Si3O10(OH)4 is a mineral named after a Jesuit missionary. Raman and infrared spectroscopy have been used to characterise the structure of the mineral. The Raman spectrum is characterised by an intense sharp band at 847 cm(-1) assigned to the ν1 (A1g) symmetric stretching vibration. Intense sharp bands at 951, 994 and 1000 cm(-1) are assigned to the ν3 (Eu, A2u, B1g) SiO4 antisymmetric stretching vibrations. Multiple ν2 SiO4 vibrational modes indicate strong distortion of the SiO4 tetrahedra. Multiple CaO and CuO stretching bands are observed. Raman spectroscopy confirmed by infrared spectroscopy clearly shows that hydroxyl units are involved in the kinoite structure. Based upon the infrared spectra, it is proposed that water is also involved in the kinoite structure. Based upon vibrational spectroscopy, the formula of kinoite is defined as Ca2Cu2Si3O10(OH)4·xH2O.

  20. Photostable Solid Dispersion of Nifedipine by Porous Calcium Silicate.

    Science.gov (United States)

    Fujimoto, Yumi; Hirai, Nobuaki; Takatani-Nakase, Tomoka; Takahashi, Koichi

    2016-01-01

    Nifedipine (NIF) is a typical light-sensitive drug requiring protection from light during manufacture, storage, and handling of its dosage forms. The purpose of this study was to evaluate the utility of porous calcium silicate (PCS) for maintaining the photostability of NIF in a solid dispersion formulation. Adsorption solid dispersion (ASD) prepared using NIF and PCS as an amorphous formulation was more stable to light irradiation than a physical mixture of NIF and microcrystalline cellulose (a control physical mixture) as a crystalline formulation. In addition, PCS in physical mixtures with NIF adequately protected NIF from photodegradation, suggesting that this protective effect could be because of some screening effect by the porous structure of PCS blocking the passage of light reaching NIF in pores of PCS. These findings suggest that PCS is useful for improving the solubility and photostability of NIF in solid dispersion formulation.

  1. Stylolites, porosity, depositional texture, and silicates in chalk facies sediments

    DEFF Research Database (Denmark)

    Fabricius, Ida Lykke; Borre, Mai K.

    2007-01-01

    Comparison of chalk on the Ontong Java Plateau and chalk in the Central North Sea indicates that, whereas pressure dissolution is controlled by effective burial stress, pore-filling cementation is controlled by temperature. Effective burial stress is caused by the weight of all overlying water...... and sediments as counteracted by the pressure in the pore fluid, so the regional overpressure in the Central North Sea is one reason why the two localities have different relationships between temperature and effective burial stress. In the chalk of the Ontong Java Plateau the onset of calcite-silicate pressure...... dissolution around 490 m below sea floor (bsf) corresponds to an interval of waning porosity-decline, and even the occurrence of proper stylolites from 830 m bsf is accompanied by only minor porosity reduction. Because opal is present, the pore-water is relatively rich in Si which through the formation of Ca...

  2. Reactivity, swelling and aggregation of mixed-size silicate nanoplatelets

    Science.gov (United States)

    Segad, M.; Cabane, B.; Jönsson, Bo

    2015-10-01

    Montmorillonite is a key ingredient in a number of technical applications. However, little is known regarding the microstructure and the forces between silicate platelets. The size of montmorillonite platelets from different natural sources can vary significantly. This has an influence on their swelling behavior in water as well as in salt solutions, particularly when tactoid formation occurs, that is when divalent counterions are present in the system. A tactoid consists of a limited number of platelets aggregated in a parallel arrangement with a constant separation. The tactoid size increases with platelet size and with very small nanoplatelets, ~30 nm, no tactoids are observed irrespectively of the platelet origin and concentration of divalent ions. The formation and dissociation of tactoids seem to be reversible processes. A large proportion of small nanoplatelets in a mixed-size system affects the tactoid formation, reduces the aggregation number and increases the extra-lamellar swelling in the system.

  3. S-Isotope Fractionation between Fluid and Silicate Melts

    Science.gov (United States)

    Fiege, A.; Holtz, F.; Shimizu, N.; Behrens, H.; Mandeville, C. W.; Simon, A. C.

    2013-12-01

    Large amounts of sulfur (S) can be released from silicate melts during volcanic eruption. Degassing of magma can lead to S-isotope fractionation between fluid and melt. However, experimental data on fluid-melt S-isotope fractionation are scarce and no data exist for silicate melts at temperatures (T) > 1000°C. Recent advances in in situ S-isotope analyses using secondary ion mass spectroscopy (SIMS) enable determinations of the isotopic composition in silicate glasses with low S content [1] and allow us to investigate experimentally fluid-melt S-isotope fractionation effects in magmatic systems. Isothermal decompression experiments were conducted in internally heated pressure vessels (IHPV). Volatile-bearing (~3 to ~8 wt% H2O, 140 to 2700 ppm S, 0 to 1000 ppm Cl) andesitic and basaltic glasses were synthesized at ~1040°C, ~500 MPa and log(fO2) = QFM to QFM+4 (QFM: quartz-magnetite-fayalite buffer). The decompression experiments were carried out at T = 1030 to 1200°C and similar fO2. Pressure (P) was released continuously from ~400 MPa to 150, 100 or 70 MPa with rates (r) ranging from 0.001 to 0.2 MPa/s. The samples were either rapidly quenched after decompression or annealed for various times (tA) at final conditions (1 to 72 h) before quenching. The volatile-bearing starting glasses and the partially degassed experimental glasses were analyzed by electron microprobe (e.g. Cl-, S-content), IR-spectroscopy (H2O content) and SIMS (δ34S). The gas-melt isotope fractionation factors (αg-m) were estimated following Holloway and Blank [2] and utilizing mass balance calculations. The results show that αg-m remains constant within error over the investigated range of r and tA, reflecting fluid-melt equilibrium fractionation of S isotopes for given T and fO2. Data obtained for oxidizing conditions (~QFM+4) are in agreement with observations in arc magmas [3] and close to what is predicted by previous theoretical and experimental data [4; 5; 6]; e.g. a α(SO2 gas - SO42

  4. Formation of siliceous sediments in brandy after diatomite filtration.

    Science.gov (United States)

    Gómez, J; Gil, M L A; de la Rosa-Fox, N; Alguacil, M

    2015-03-01

    Brandy is quite a stable spirit but sometimes light sediment appears. This sediment was separated and analysed by IR and SEM-EDX. It was revealed that the sediment is composed mostly of silica and residual organic matter. Silica was present as an amorphous phase and as microparticles. In an attempt to reproduce the formation of the sediment, a diatomite extract was prepared with an ethanol/water mixture (36% vol.) and a calcined diatomite similar to that used in brandy filtration. This extract was added to unfiltered brandy in different amounts. After 1 month, the Si concentration decreased in all samples and sediments with similar compositions and features to those found in the unstable brandy appeared. The amounts of sediment obtained were directly related to the decrease in Si concentration in solution. Consequently, it can be concluded that siliceous sediment in brandy originates from Si released during diatomite filtration. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Shrinking core models applied to the sodium silicate production process

    Directory of Open Access Journals (Sweden)

    Stanković Mirjana S.

    2007-01-01

    Full Text Available The sodium silicate production process, with the molar ratio SiO2/Na2O = 2, for detergent zeolite 4A production, is based on quartz sand dissolving in NaOH aqueous solution, with a specific molality. It is a complex process performed at high temperature and pressure. It is of vital importance to develop adequate mathematical models, which are able to predict the dynamical response of the process parameters. A few kinetic models were developed within this study, which were adjusted and later compared to experimental results. It was assumed that SiO2 particles are smooth spheres, with uniform diameter. This diameter decreases during dissolving. The influence of particle diameter, working temperature and hydroxide ion molality on the dissolution kinetics was investigated. It was concluded that the developed models are sufficiently correct, in the engineering sense, and can be used for the dynamical prediction of process parameters.

  6. Photoluminescence in amorphous MgSiO_3 silicate

    CERN Document Server

    Thompson, S P; Day, S J; Connor, L D; Evans, A

    2013-01-01

    Samples of amorphous MgSiO_3 annealed at temperature steps leading up to their crystallisation temperature show a rise in photoluminescence activity, peaking at ~450C. The photoluminescence band has a main peak at 595nm and a weaker peak at 624nm. We present laboratory data to show that the maximum in photoluminescence activity is related to substantial structural reordering that occurs within a relatively narrow temperature range. We attribute the origin of the photoluminescence to non-bridging oxygen hole centre defects, which form around ordered nano-sized domain structures as a result of the breakup of tetrahedral connectivity in the disordered inter-domain network, aided by the loss of bonded OH. These defects are removed as crystallisation progresses, resulting in the decrease and eventual loss of photoluminescence. Thermally processed hydrogenated amorphous silicate grains could therefore represent a potential carrier of extended red emission.

  7. High-dose dosimetry using natural silicate minerals

    Energy Technology Data Exchange (ETDEWEB)

    Carmo, Lucas S. do; Mendes, Leticia, E-mail: isatiro@usp.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Watanabe, Shigueo; Rao, Gundu; Lucas, Natasha; Sato, Karina, E-mail: lacifid@if.usp.br [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Instituto de Fisica. Departamento de Fisica Nuclear; Barbosa, Renata F., E-mail: profcelta@hotmail.com [Universidade Federal de Sao Paulo (UNIFESP), Santos, SP (Brazil). Departamento de Ciencias do Mar

    2015-07-01

    In the present study, certain natural silicate minerals such as aquamarine (AB), morganite (PB), goshenite (WB), white jadeite (JW), green jadeite (JG), pink tourmaline (PT) and two varieties of jadeite-like quartz, denoted here by JQ1 and JQ2, were investigated using the thermoluminescence technique to evaluate their potential for use as very-high- and high-dose dosimeters. These minerals respond to high doses of γ-rays of up to 1000 kGy and often to very high doses of up to 3000 kGy. The TL response of these minerals may be considered to be satisfactory for applications in high-dose dosimetry. Investigations of electron paramagnetic resonance and optically stimulated luminescence dosimetry are in progress. (author)

  8. Copper metallurgy at the crossroads

    Directory of Open Access Journals (Sweden)

    Habashi F.

    2007-01-01

    Full Text Available Copper technology changed from the vertical to the horizontal furnace and from the roast reaction to converting towards the end of the last century. However, the horizontal furnace proved to be an inefficient and polluting reactor. As a result many attempts were made to replace it. In the past 50 years new successful melting processes were introduced on an industrial scale that were more energy efficient and less polluting. In addition, smelting and converting were conducted in a single reactor in which the concentrate was fed and the raw copper was produced. The standing problem in many countries, however, is marketing 3 tonnes of sulfuric acid per tonne of copper produced as well as emitting large amounts of excess SO2 in the atmosphere. Pressure hydrometallurgy offers the possibility of liberating the copper industry from SO2 problem. Heap leaching technology has become a gigantic operation. Combined with solvent extraction and electrowinning it contributes today to about 20% of copper production and is expected to grow. Pressure leaching offers the possibility of liberating the copper industry from SO2 problem. The technology is over hundred years old. It is applied for leaching a variety of ores and concentrates. Hydrothermal oxidation of sulfide concentrates has the enormous advantage of producing elemental sulfur, hence solving the SO2 and sulfuric acid problems found in smelters. Precipitation of metals such as nickel and cobalt under hydrothermal conditions has been used for over 50 years. It has the advantage of a compact plant but the disadvantage of producing ammonium sulfate as a co-product. In case of copper, however, precipitation takes place without the need of neutralizing the acid, which is a great advantage and could be an excellent substitute for electrowinning which is energy intensive and occupies extensive space. Recent advances in the engineering aspects of pressure equipment design open the door widely for increased

  9. Evaluation of apatite silicates as solid oxide fuel cell electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Marrero-Lopez, D. [Dpto. de Fisica Aplicada I, Laboratorio de Materiales y Superficies (Unidad Asociada al C.S.I.C.), Universidad de Malaga, 29071 Malaga (Spain); Dpto. de Quimica Inorganica, Universidad de La Laguna, 38200 La Laguna, Tenerife (Spain); Martin-Sedeno, M.C.; Aranda, M.A.G. [Dpto. de Quimica Inorganica, Universidad Malaga, 29071 Malaga (Spain); Pena-Martinez, J. [Dpto. de Quimica Inorganica, Universidad de La Laguna, 38200 La Laguna, Tenerife (Spain); Instituto de Energias Renovables, Parque Tecnologico, Universidad de Castilla La Mancha, 02006 Albacete (Spain); Ruiz-Morales, J.C.; Nunez, P. [Dpto. de Quimica Inorganica, Universidad de La Laguna, 38200 La Laguna, Tenerife (Spain); Ramos-Barrado, J.R. [Dpto. de Fisica Aplicada I, Laboratorio de Materiales y Superficies (Unidad Asociada al C.S.I.C.), Universidad de Malaga, 29071 Malaga (Spain)

    2010-05-01

    Apatite-type silicates have been considered as promising electrolytes for Solid Oxide Fuel Cells (SOFC); however studies on the potential use of these materials in SOFC devices have received relatively little attention. The lanthanum silicate with composition La{sub 10}Si{sub 5.5}Al{sub 0.5}O{sub 26.75} has been evaluated as electrolyte with the electrode materials commonly used in SOFC, i.e. manganite, ferrite and cobaltite as cathode materials and NiO-CGO composite, chromium-manganite and Sr{sub 2}MgMoO{sub 6} as anode materials. Chemical compatibility, area-specific resistance and fuel cell studies have been performed. X-ray powder diffraction (XRPD) analysis did not reveal any trace of reaction products between the apatite electrolyte and most of the aforementioned electrode materials. However, the area-specific polarisation resistance (ASR) of these electrodes in contact with apatite electrolyte increased significantly with the sintering temperature, indicating reactivity at the electrolyte/electrode interface. On the other hand, the ASR values are significantly improved using a ceria buffer layer between the electrolyte and electrode materials to prevent reactivity. Maximum power densities of 195 and 65 mWcm{sup -2} were obtained at 850 and 700 C, respectively in H{sub 2} fuel, using an 1 mm-thick electrolyte, a NiO-Ce{sub 0.8}Gd{sub 0.2}O{sub 1.9} composite as anode and La{sub 0.6}Sr{sub 0.4}Co{sub 0.8}Fe{sub 0.2}O{sub 3-{delta}} as cathode materials. This fuel cell was tested for 100 h in 5%H{sub 2}-Ar atmosphere showing stable performance. (author)

  10. Modified tricalcium silicate cement formulations with added zirconium oxide.

    Science.gov (United States)

    Li, Xin; Yoshihara, Kumiko; De Munck, Jan; Cokic, Stevan; Pongprueksa, Pong; Putzeys, Eveline; Pedano, Mariano; Chen, Zhi; Van Landuyt, Kirsten; Van Meerbeek, Bart

    2017-04-01

    This study aims to investigate the effect of modifying tricalcium silicate (TCS) cements on three key properties by adding ZrO2. TCS powders were prepared by adding ZrO2 at six different concentrations. The powders were mixed with 1 M CaCl2 solution at a 3:1 weight ratio. Biodentine (contains 5 wt.% ZrO2) served as control. To evaluate the potential effect on mechanical properties, the mini-fracture toughness (mini-FT) was measured. Regarding bioactivity, Ca release was assessed using ICP-AES. The component distribution within the cement matrix was evaluated by Feg-SEM/EPMA. Cytotoxicity was assessed using an XTT assay. Adding ZrO2 to TCS did not alter the mini-FT (p = 0.52), which remained in range of that of Biodentine (p = 0.31). Ca release from TSC cements was slightly lower than that from Biodentine at 1 day (p > 0.05). After 1 week, Ca release from TCS 30 and TCS 50 increased to a level that was significantly higher than that from Biodentine (p  0.05). EPMA revealed a more even distribution of ZrO2 within the TCS cements. Particles with an un-reacted core were surrounded by a hydration zone. The 24-, 48-, and 72-h extracts of TCS 50 were the least cytotoxic. ZrO2 can be added to TCS without affecting the mini-FT; Ca release was reduced initially, to reach a prolonged release thereafter; adding ZrO2 made TCS cements more biocompatible. TCS 50 is a promising cement formulation to serve as a biocompatible hydraulic calcium silicate cement.

  11. A-thermal elastic behavior of silicate glasses.

    Science.gov (United States)

    Rabia, Mohammed Kamel; Degioanni, Simon; Martinet, Christine; Le Brusq, Jacques; Champagnon, Bernard; Vouagner, Dominique

    2016-02-24

    Depending on the composition of silicate glasses, their elastic moduli can increase or decrease as function of the temperature. Studying the Brillouin frequency shift of these glasses versus temperature allows the a-thermal composition corresponding to an intermediate glass to be determined. In an intermediate glass, the elastic moduli are independent of the temperature over a large temperature range. For sodium alumino-silicate glasses, the a-thermal composition is close to the albite glass (NaAlSi3O8). The structural origin of this property is studied by in situ high temperature Raman scattering. The structure of the intermediate albite glass and of silica are compared at different temperatures between room temperature and 600 °C. When the temperature increases, it is shown that the high frequency shift of the main band at 440 cm(-1) in silica is a consequence of the cristobalite-like alpha-beta transformation of 6-membered rings. This effect is stronger in silica than bond elongation (anharmonic effects). As a consequence, the elastic moduli of silica increase as the temperature increases. In the albite glass, the substitution of 25% of Si(4+) ions by Al(3+) and Na(+) ions decreases the proportion of SiO2 6-membered rings responsible for the silica anomaly. The effects of the silica anomaly balance the anharmonicity in albite glass and give rise to an intermediate a-thermal glass. Different networks, formers or modifiers, can be added to produce different a-thermal glasses with useful mechanical or chemical properties.

  12. Low Velocity Sphere Impact of a Soda Lime Silicate Glass

    Energy Technology Data Exchange (ETDEWEB)

    Wereszczak, Andrew A [ORNL; Fox, Ethan E [ORNL; Morrissey, Timothy G [ORNL; Vuono, Daniel J [ORNL

    2011-10-01

    This report summarizes TARDEC-sponsored work at Oak Ridge National Laboratory (ORNL) during the FY11 involving low velocity (< 30 m/s or < 65 mph) ball impact testing of Starphire soda lime silicate glass. The intent was to better understand low velocity impact response in the Starphire for sphere densities that bracketed that of rock. Five sphere materials were used: borosilicate glass, soda-lime silicate glass, steel, silicon nitride, and alumina. A gas gun was fabricated to produce controlled velocity delivery of the spheres against Starphire tile targets. Minimum impact velocities to initiate fracture in the Starphire were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between the any of the five sphere-Starphire-target combinations. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) Frictional effects contribute to fracture initiation. (2) Spheres with a lower elastic modulus require less force to initiate fracture in the Starphire than spheres with a higher elastic modulus. (3) Contact-induced fracture did not initiate in the Starphire SLS for impact kinetic energies < 150 mJ. Fracture sometimes initiated or kinetic energies between {approx} 150-1100 mJ; however, it tended to occur when lower elastic modulus spheres were impacting it. Contact-induced fracture would always occur for impact energies > 1100 mJ. (4) The force necessary to initiate contact-induced fracture is higher under dynamic or impact conditions than it is under quasi-static indentation conditions. (5) Among the five used sphere materials, silicon nitride was the closest match to 'rock' in terms of both density and (probably) elastic modulus.

  13. 40 CFR 721.3100 - Oligomeric silicic acid ester compound with a hy-droxyl-al-kyla-mine.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Oligomeric silicic acid ester compound... Significant New Uses for Specific Chemical Substances § 721.3100 Oligomeric silicic acid ester compound with a... chemical substance identified generically as oligomeric silicic acid ester compound with...

  14. A Study of Siliceous Pneumoconiosis in a Desert Area of Sunan County,Gansu Province,China

    Institute of Scientific and Technical Information of China (English)

    1993-01-01

    Three hundred and ninety five residents in a desert area were examined with chest radiographs and 28 cases with siliceous pneumoconiosis were found.The prevalence of siliceous pneumoconiosis was 7.09%,and that over 40 years of age was 21%.The histological findings of lungs from a camel living in that area for 20 years also confirmed to have siliceous pneumoconiosis.

  15. Microbial and copper adsorption by smectitic clay--an experimental study.

    Science.gov (United States)

    Hassen, A; Jamoussi, F; Saidi, N; Mabrouki, Z; Fakhfakh, E

    2003-09-01

    The objective of this study was to quantify copper-, bacteria- and bacteriophage-binding capacities of natural clay with the aim of predicting the adsorption of heavy metals, human pathogenic bacteria and viruses by a clayey landfill liner. X-ray diffraction analysis of six natural clays showed that the dominant phase in all deposits consists of smectites together with illite, kaolin and, sometimes, palygorskite and sepiolite. The specific surface areas of different clay substrates were very high ranging from 293 to 351 m2 g(-1), and indicating a high proportion of phyllosilicates, consisting especially of smectites. The physico-chemical identification of separated smectites showed a high potential adsorbent character indicative of a large industrial use. The Kb12 smectite substrate chosen arbitrarily among six separated substrates, appeared as an excellent copper adsorbent. Copper was adsorbed to clay in a proportion ranging from 94.6 to 96.0% with an average of 95.1% and its adsorption occurred rapidly in less than 30 min. Organic contents of the clay substrate, evaluated as 17% of dry mass, may contribute and enhance copper adsorption. Different elution protocols using distilled water, 2 and/or 5% nitric acid revealed that while nitric acid resulted in the removal of more than 59% of the metal at the lower concentration and its complete depletion with a further elution at the higher concentration, distilled water alone was unable to remove more than 1% of adsorbed copper. This finding suggested that copper ions form high-energy bonds with layer-silicate surfaces. Interestingly, the use of a regenerated substrate as copper adsorbent subsequent to abundant washings of the used substrate consecutively, with 0.1 N HNO3 and distilled water, reduced copper adsorption by approximately 14%, suggesting a slight disturbance of clay initial structure. Batch adsorption experiments with phage T7 and raw clay Kb12 showed that the tested clay substrate appeared as a relatively

  16. 21 CFR 73.1125 - Potassium sodium copper chloropyhllin (chlorophyllin-copper complex).

    Science.gov (United States)

    2010-04-01

    ... (chlorophyllin-copper complex). 73.1125 Section 73.1125 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT....1125 Potassium sodium copper chloropyhllin (chlorophyllin-copper complex). (a) Identity. (1) The color additive potassium sodium copper chlorophyllin is a green to black powder obtained from chlorophyll...

  17. 21 CFR 73.2125 - Potassium sodium copper chlorophyllin (chlorophyllin-copper complex).

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Potassium sodium copper chlorophyllin (chlorophyllin-copper complex). 73.2125 Section 73.2125 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT... § 73.2125 Potassium sodium copper chlorophyllin (chlorophyllin-copper complex). (a) Identity...

  18. Testing Corrosion Inhibitors for the Conservation of Archaeological Copper and Copper Alloys

    Directory of Open Access Journals (Sweden)

    Robert B. Faltermeier

    1997-11-01

    Full Text Available This is a synopsis of the Ph.D. research undertaken at the Institute of Archaeology, University College London. The aim was to evaluate corrosion inhibitors for use in the conservation of copper and copper alloy archaeological artefacts. The objective of this work was to acquire an insight into the performance of copper corrosion inhibitors, when applied to archaeological copper.

  19. The link between copper and Wilson's disease.

    Science.gov (United States)

    Purchase, Rupert

    2013-01-01

    Wilson's disease (hepatolenticular degeneration) is a rare inherited autosomal recessive disorder of copper metabolism leading to copper accumulation in the liver and extrahepatic organs such as the brain and cornea. Patients may present with combinations of hepatic, neurological and psychiatric symptoms. Copper is the therapeutic target for the treatment of Wilson's disease. But how did copper come to be linked with Wilson's disease? The answer encompasses a study of enzootic neonatal ataxia in lambs in the 1930s, the copper-chelating properties of British Anti-Lewisite, and the chemical analysis for copper of the organs of deceased Wilson's disease patients in the mid-to-late 1940s. Wilson's disease is one of a number of copper-related disorders where loss of copper homeostasis as a result of genetic, nutritional or environmental factors affects human health.

  20. Determination of copper in clarified apple juices.

    Science.gov (United States)

    Zeiner, Michaela; Juranović Cindrić, Iva; Kröppl, Michaela; Stingeder, Gerhard

    2010-03-24

    Inorganic copper compounds are not considered as synthetic fertilizers for apple trees as they are traditional fertilizers. Thus, they are used in organic farming for soil or foliar applications. The European Union is for health reasons interested in reducing copper in apple orchards. Because the fertilizer application rate affects the nutrition of apples, the applied copper might also be reflected in the copper concentration of apple juices. Thus, the determination of copper is of concern for investigating the application of copper-containing fertilizers. Samples of clarified apple juice commercially available in the European market were analyzed for their copper content. Prior to quantification by inductively coupled plasma-optical emission spectrometry, the juices were processed by a microwave-assisted digestion system using HNO(3). All samples were also measured directly after dilution with HNO(3). The copper concentrations measured using both methods were all below the limit of detection (17 microg/L).

  1. Synthesis of aminoarenethiolato-copper(I) complexes

    NARCIS (Netherlands)

    Sperotto, E.; van Klink, G.P.M.; van Koten, G.

    2008-01-01

    Copper(I)-mediated reactions have recently become the choice for large industrial scale applications, since copper is environmentally friendly and cheaper than other transition metals already explored. However, most organocopper compounds still present several limitations including the sensitivity t

  2. Global assessment of undiscovered copper resources

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — Deposits, prospects, and permissive tracts for porphyry and sediment-hosted copper resources worldwide, with estimates of undiscovered copper resources. pCu_tracts...

  3. EFFECT OF COPPER ON PASSIVITY AND CORROSION ...

    African Journals Online (AJOL)

    2014-06-30

    Jun 30, 2014 ... metallic copper enriched on the surface film of austenitic stainless ... Dispersed inclusions of this phase can influence the stability of .... two microstructures showed that copper concentration possessed a non-uniform chemical.

  4. Copper tolerance and virulence in bacteria

    Science.gov (United States)

    Ladomersky, Erik; Petris, Michael J.

    2015-01-01

    Copper (Cu) is an essential trace element for all aerobic organisms. It functions as a cofactor in enzymes that catalyze a wide variety of redox reactions due to its ability to cycle between two oxidation states, Cu(I) and Cu(II). This same redox property of copper has the potential to cause toxicity if copper homeostasis is not maintained. Studies suggest that the toxic properties of copper are harnessed by the innate immune system of the host to kill bacteria. To counter such defenses, bacteria rely on copper tolerance genes for virulence within the host. These discoveries suggest bacterial copper intoxication is a component of host nutritional immunity, thus expanding our knowledge of the roles of copper in biology. This review summarizes our current understanding of copper tolerance in bacteria, and the extent to which these pathways contribute to bacterial virulence within the host. PMID:25652326

  5. Preparation of Pure Copper Powder from Acidic Copper Chloride Waste Etchant

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The method for the recycling of copper from copper chloride solution was developed. This process consists of extraction of copper, purification and particle size reduction. In the first step, reductive metal scraps were added to acidic copper chloride waste enchants produced in the PCB industry to obtain copper powder.Composition analysis showed that this powder contained impurities such as Fe, Ni, and water. So, drying and purification were carried out by using microwave and a centrifugal separator. Thereby the copper powder had a purity of higher than 99% and spherical form in morphology. The copper powder size was decreased by ball milling.

  6. Coating of a steel wire with copper

    Science.gov (United States)

    Vdovin, K. N.; Dubskii, G. A.; Nefed'ev, A. A.; Derevyanko, D. V.

    2016-03-01

    The process of coating of a steel wire with liquid copper at a high speed (>1 m/s) is considered. The results of long-term studies of copperizing under laboratory conditions and electron-microscopic investigation of the copper-steel adhesion are used to develop a mathematical model for coating of a steel wire with copper and to create a commercial setup to implement this process.

  7. Canine Models for Copper Homeostasis Disorders

    OpenAIRE

    Xiaoyan Wu; Leegwater, Peter A. J.; Hille Fieten

    2016-01-01

    Copper is an essential trace nutrient metal involved in a multitude of cellular processes. Hereditary defects in copper metabolism result in disorders with a severe clinical course such as Wilson disease and Menkes disease. In Wilson disease, copper accumulation leads to liver cirrhosis and neurological impairments. A lack in genotype-phenotype correlation in Wilson disease points toward the influence of environmental factors or modifying genes. In a number of Non-Wilsonian forms of copper me...

  8. 49 CFR 192.279 - Copper pipe.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Copper pipe. 192.279 Section 192.279... Copper pipe. Copper pipe may not be threaded except that copper pipe used for joining screw fittings or... heavier wall pipe listed in Table C1 of ASME/ANSI B16.5. [Amdt. 192-62, 54 FR 5628, Feb. 6, 1989, as...

  9. Modulation of tau phosphorylation by environmental copper

    OpenAIRE

    Voss, Kellen; Harris, Christopher; Ralle, Martina; Duffy, Megan; Murchison, Charles; Joseph F. Quinn

    2014-01-01

    Background The transition metal copper enhances amyloid β aggregation and neurotoxicity, and in models of concomitant amyloid and tau pathology, copper also promotes tau aggregation. Since it is not clear if the effects of environmental copper upon tau pathology are dependent on the presence of pathological amyloid β, we tested the effects of copper overload and complexing in disease models which lack pathological amyloid β. Methods We used cell culture and transgenic murine models to test th...

  10. Canine Models for Copper Homeostasis Disorders

    OpenAIRE

    Xiaoyan Wu; Leegwater, Peter A.J.; Hille Fieten

    2016-01-01

    Copper is an essential trace nutrient metal involved in a multitude of cellular processes. Hereditary defects in copper metabolism result in disorders with a severe clinical course such as Wilson disease and Menkes disease. In Wilson disease, copper accumulation leads to liver cirrhosis and neurological impairments. A lack in genotype-phenotype correlation in Wilson disease points toward the influence of environmental factors or modifying genes. In a number of Non-Wilsonian forms of copper me...

  11. Evaluation of the effect of sodium silicate addition to mine backfill, Gelfill − Part 1

    Directory of Open Access Journals (Sweden)

    M. Kermani

    2015-06-01

    Full Text Available In this paper, the mechanical properties of sodium silicate-fortified backfill, called Gelfill, were investigated by conducting a series of laboratory experiments. Two configurations were tested, i.e. Gelfill and cemented hydraulic fill (CHF. The Gelfill has an alkali activator such as sodium silicate in its materials in addition to primary materials of mine backfill which are tailings, water and binders. Large numbers of samples of Gelfill and CHF with various mixture designs were cast and cured for over 28 d. The mechanical properties of samples were investigated using uniaxial compression test, and the results were compared with those of reference samples made without sodium silicate. The test results indicated that the addition of an appropriate amount of an alkali activator such as sodium silicate can enhance the mechanical (uniaxial compressive strength and physical (water retention properties of backfill. The microstructure analysis conducted by mercury intrusion porosimetry (MIP revealed that the addition of sodium silicate can modify the pore size distribution and total porosity of Gelfill, which can contribute to the better mechanical properties of Gelfill. It was also shown that the time and rate of drainage in the Gelfill specimens are less than those in CHF specimens made without sodium silicate. Finally, the study showed that the addition of sodium silicate can reduce the required setting time of mine backfill, which can contribute to increase mine production in accordance with the mine safety.

  12. Evaluation of the effect of sodium silicate addition to mine backfill, Gelfill L Part 1

    Institute of Scientific and Technical Information of China (English)

    M. Kermani; F.P. Hassani; E. Aflaki; M. Benzaazoua; M. Nokken

    2015-01-01

    In this paper, the mechanical properties of sodium silicate-fortified backfill, called Gelfill, were investi-gated by conducting a series of laboratory experiments. Two configurations were tested, i.e. Gelfill and cemented hydraulic fill (CHF). The Gelfill has an alkali activator such as sodium silicate in its materials in addition to primary materials of mine backfill which are tailings, water and binders. Large numbers of samples of Gelfill and CHF with various mixture designs were cast and cured for over 28 d. The me-chanical properties of samples were investigated using uniaxial compression test, and the results were compared with those of reference samples made without sodium silicate. The test results indicated that the addition of an appropriate amount of an alkali activator such as sodium silicate can enhance the mechanical (uniaxial compressive strength) and physical (water retention) properties of backfill. The microstructure analysis conducted by mercury intrusion porosimetry (MIP) revealed that the addition of sodium silicate can modify the pore size distribution and total porosity of Gelfill, which can contribute to the better mechanical properties of Gelfill. It was also shown that the time and rate of drainage in the Gelfill specimens are less than those in CHF specimens made without sodium silicate. Finally, the study showed that the addition of sodium silicate can reduce the required setting time of mine backfill, which can contribute to increase mine production in accordance with the mine safety.

  13. On the Relation of Silicates and SiO Maser in Evolved Stars

    Science.gov (United States)

    Liu, Jiaming; Jiang, Biwei

    2017-04-01

    The SiO molecule is one of the candidates for the seed of silicate dust in the circumstellar envelope of evolved stars, but this opinion is challenged. In this work we investigate the relation of the SiO maser emission power and the silicate dust emission power. With both our own observation by using the PMO/Delingha 13.7 m telescope and archive data, a sample is assembled of 21 SiO v = 1, J = 2 - 1 sources and 28 SiO v = 1, J = 1 - 0 sources that exhibit silicate emission features in the ISO/SWS spectrum as well. The analysis of their SiO maser and silicate emission power indicates a clear correlation, which is not against the hypothesis that the SiO molecules are the seed nuclei of silicate dust. On the other hand, no correlation is found between SiO maser and silicate crystallinity, which may imply that silicate crystallinity does not correlate with mass-loss rate.

  14. Nonmare volcanism on the Moon: Photometric evidence for the presence of evolved silicic materials

    Science.gov (United States)

    Clegg-Watkins, R. N.; Jolliff, B. L.; Watkins, M. J.; Coman, E.; Giguere, T. A.; Stopar, J. D.; Lawrence, S. J.

    2017-03-01

    Images and photometric data from the Lunar Reconnaissance Orbiter Camera (LROC) Narrow Angle Cameras (NACs) are used to investigate regions of the Moon inferred from previous remote sensing compositional studies to be associated with nonmare, silicic volcanics. Specifically, LROC NAC imagery, with photometry normalized to account for local slopes using NAC Digital Terrain Models (DTMs), was used to investigate the exposed areas associated with the Compton-Belkovich Volcanic Complex (CBVC), Hansteen Alpha Volcanic Complex (HAVC), Lassell Massif (LM), Gruithuisen Domes (GD), and ejecta of Aristarchus Crater (AC). Photometric studies of spacecraft landing sites, for which ground-truth compositional data exist, allow us to study the relationship between photometric properties of soils and their mineralogical and chemical compositions. The silicic regions have high reflectance and single scattering albedos that are consistent with different proportions of highly reflective minerals including alkali feldspar and quartz, and low concentrations of mafic minerals. Of the silicic sites studied, the CBVC has the highest reflectance values and single scattering albedos. Silicic pyroclastic deposits may also occur at the CBVC, and we present evidence from laboratory spectra that an addition of up to ∼20 wt% glassy silicic materials to a highlands-type regolith simulant can account for the increased reflectance of these volcanic regions. Reflectance variations across and within the sites can be explained by mixing of felsic mineral components, evolved-to-intermediate silicic compositions, and/or silicic pyroclastic deposits.

  15. Valence determination of rare earth elements in lanthanide silicates by L 3-XANES spectroscopy

    Science.gov (United States)

    Kravtsova, Antonina N.; Guda, Alexander A.; Goettlicher, Joerg; Soldatov, Alexander V.; Taroev, Vladimir K.; Kashaev, Anvar A.; Suvorova, Lyudmila F.; Tauson, Vladimir L.

    2016-05-01

    Lanthanide silicates have been hydrothermally synthesized using Cu and Ni containers. Chemical formulae of the synthesized compounds correspond to K3Eu[Si6O15] 2H2O, HK6Eu[Si10O25], K7Sm3[Si12O32], K2Sm[AlSi4O12] 0.375H2O, K4Yb2[Si8O21], K4Ce2[Al2Si8O24]. The oxidation state of lanthanides (Eu, Ce, Tb, Sm, Yb) in these silicates has been determined using XANES spectroscopy at the Eu, Ce, Tb, Sm, Yb, L 3- edges. The experimental XANES spectra were recorded using the synchrotron radiation source ANKA (Karlsruhe Institute of Technology) and the X-ray laboratory spectrometer Rigaku R- XAS. By comparing the absorption edge energies and white line intensities of the silicates with the ones of reference spectra the oxidation state of lanthanides Eu, Ce, Tb, Sm, Yb has been found to be equal to +3 in all investigated silicates except of the Ce-containing silicate from the run in Cu container where the cerium oxidation state ranges from +3 (Ce in silicate apatite and in a KCe silicate with Si12O32 layers) to +4 (starting CeO2 or oxidized Ce2O3).

  16. On the Anomalous Silicate Absorption Feature of the Prototypical Seyfert 2 Galaxy NGC 1068

    CERN Document Server

    Koehler, Melanie

    2012-01-01

    The first detection of the silicate absorption feature in AGNs was made at 9.7 micrometer for the prototypical Seyfert 2 galaxy NGC 1068 over 30 years ago, indicating the presence of a large column of silicate dust in the line-of-sight to the nucleus. It is now well recognized that type 2 AGNs exhibit prominent silicate absorption bands, while the silicate bands of type 1 AGNs appear in emission. More recently, using the Mid-Infrared Interferometric Instrument on the Very Large Telescope Interferometer, Jaffe et al. (2004) by the first time spatially resolved the parsec-sized dust torus around NGC 1068 and found that the 10 micrometer silicate absorption feature of the innermost hot component exhibits an anomalous profile differing from that of the interstellar medium and that of common olivine-type silicate dust. While they ascribed the anomalous absorption profile to gehlenite (Ca_2Al_2SiO_7, a calcium aluminum silicate species), we propose a physical dust model and argue that, although the presence of gehl...

  17. Effect of silicate incorporation on in vivo responses of α-tricalcium phosphate ceramics.

    Science.gov (United States)

    Kamitakahara, Masanobu; Tatsukawa, Eri; Shibata, Yasuaki; Umemoto, Shota; Yokoi, Taishi; Ioku, Koji; Ikeda, Tohru

    2016-05-01

    In addition to calcium phosphate-based ceramics, glass-based materials have been utilized as bone substitutes, and silicate in these materials has been suggested to contribute to their ability to stimulate bone repair. In this study, a silicate-containing α-tricalcium phosphate (α-TCP) ceramic was prepared using a wet chemical process. Porous granules composed of silicate-containing α-TCP, for which the starting composition had a molar ratio of 0.05 for Si/(P + Si), and silicate-free α-TCP were prepared and evaluated in vivo. When implanted into bone defects that were created in rat femurs, α-TCP ceramics either with or without silicate were biodegraded, generating a hybrid tissue composed of residual ceramic granules and newly formed bone, which had a tissue architecture similar to physiological trabecular structures, and aided regeneration of the bone defects. Supplementation with silicate significantly promoted osteogenesis and delayed biodegradation of α-TCP. These results suggest that silicate-containing α-TCP is advantageous for initial skeletal fixation and wound regeneration in bone repair.

  18. Probing Interstellar Silicate Dust Grain Properties in Quasar Absorption Systems at Redshifts z<1.4

    CERN Document Server

    Aller, Monique C; York, Donald G; Welty, Daniel E; Vladilo, Giovanni; Som, Debopam

    2014-01-01

    Absorption lines in the spectra of distant quasars whose sightlines pass through foreground galaxies provide a valuable tool to probe the dust and gas compositions of the interstellar medium (ISM) in galaxies. The first evidence of silicate dust in a quasar absorption system (QAS) was provided through our detection of the 10 micron silicate feature in the z=0.52 absorber toward the quasar AO 0235+164. We present results from 2 follow-up programs using archival Spitzer Space Telescope infrared spectra to study the interstellar silicate dust grain properties in a total of 13 QASs at 0.1silicate feature in the QASs studied. We also detect the 18 micron silicate feature in the sources with adequate spectral coverage. We find variations in the breadth, peak wavelength, and substructure of the 10 micron interstellar silicate absorption features among the absorbers. This suggests that the silicate dust grain properties in these distant galaxies may differ relat...

  19. Tensile behavior of nanocrystalline copper

    Energy Technology Data Exchange (ETDEWEB)

    Sanders, P.G.; Weertman, J.R. [Northwestern Univ., Evanston, IL (United States). Dept. of Materials Science and Engineering; Eastman, J.A. [Northwestern Univ., Evanston, IL (United States). Dept. of Materials Science and Engineering]|[Argonne National Lab., IL (United States). Materials Science Div.

    1995-11-01

    High density nanocrystalline copper produced by inert gas condensation was tested in tension. Displacements were measured using foil strain gauges, which greatly improved the accuracy of the strain data. The Young`s modulus of nanocrystalline copper was found to be consistent with that of coarse-grained copper. Total elongations of {approx} 1% were observed in samples with grain sizes less than 50 nm, while a sample with a grain size of 110 nm exhibited more than 10% elongation, perhaps signifying a change to a dislocation-based deformation mechanism in the larger-grained material. In addition, tensile tests were performed as a function of strain rate, with a possible trend of decreased strength and increased elongation as the strain rate was decreased.

  20. Monitoring copper in Wilson's disease.

    Science.gov (United States)

    Walshe, J M

    2010-01-01

    Monitoring copper metabolism in patients with Wilson's disease is not an exact science. At present, there are no simple methods of estimating the total body load of this metal. Indirect methods must therefore be used. A survey of the current literature shows that most approaches rely on the determination of blood and urine copper concentration. Both these should decrease with treatment. In parallel with decreased copper concentration, there should be subsequent improvement in more routine laboratory tests including liver and renal function, blood count parameters, and clotting factors. Lack of compliance is revealed by a reversal of this trend. This chapter critically reviews current testing methods and describes other approaches that may be helpful.

  1. Mechanochemical reduction of copper sulfide

    DEFF Research Database (Denmark)

    Balaz, P.; Takacs, L.; Jiang, Jianzhong

    2002-01-01

    The mechanochemical reduction of copper sulfide with iron was induced in a Fritsch P-6 planetary mill, using WC vial filled with argon and WC balls. Samples milled for specific intervals were analyzed by XRD and Mossbauer spectroscopy. Most of the reaction takes place during the first 10 min...... of milling and only FeS and Cu are found after 60 min. The main chemical process is accompanied by phase transformations of the sulfide phases as a result of milling. Djurleite partially transformed to chalcocite and a tetragonal copper sulfide phase before reduction. The cubic modification of FeS was formed...... first, transforming to hexagonal during the later stages of the process. The formation of off-stoichiometric phases and the release of some elemental sulfur by copper sulfide are also probable....

  2. Copper tolerance of Trichoderma species

    Directory of Open Access Journals (Sweden)

    Jovičić-Petrović Jelena

    2014-01-01

    Full Text Available Some Trichoderma strains can persist in ecosystems with high concentrations of heavy metals. The aim of this research was to examine the variability of Trichoderma strains isolated from different ecosystems, based on their morphological properties and restriction analysis of ITS fragments. The fungal growth was tested on potato dextrose agar, amended with Cu(II concentrations ranging from 0.25 to 10 mmol/l, in order to identify copper-resistant strains. The results indicate that some isolated strains of Trichoderma sp. show tolerance to higher copper concentrations. Further research to examine the ability of copper bioaccumulation by tolerant Trichoderma strains is needed. [Projekat Ministarstva nauke Republike Srbije, br. TR 31080 i br. III 43010

  3. Preparation and Characterization of Lithium Zirconium Silicate for CO2 Capture

    Directory of Open Access Journals (Sweden)

    T.S. Bhosale

    2014-10-01

    Full Text Available The samples of lithium zirconium silicate were prepared by precipitation, template and sol-gel meth-ods. The samples were prepared with several mol ratios of Li:Zr:Si. The preparation of lithium zirco-nium silicate samples by precipitation method were carried out by using the lithium nitrate, zirconyl nitrate, zirconium(IV oxypropoxide and tetramethylorthosilicate (TEOS as precursors. The samples of lithium zirconium silicate were prepared by using cetyltrimethyl-ammonium bromide (C-TAB and tetramethyl ammonium hydroxide (TMAOH by template method. The samples of lithium zirconium silicate were characterized by XRD, TEM, SEM, 29Si-MAS NMR and FTIR. The surface area, alkalinity / acidity of the samples of lithium zirconium silicate were measured. The TGA analysis of lithium zirco-nium silicate samples was done. The CO2 captured by the samples of lithium zirconium silicate was es-timated. The captured CO2 by the samples of lithium zirconium silicate was found to be in the range 3.3 to 8.6 wt%. © 2014 BCREC UNDIP. All rights reservedReceived: 27th March 2014; Revised: 31st July 2014; Accepted: 2nd August 2014How to Cite: Bhosale, T.S. , Gaikwad, A.G. (2014. Preparation and Characterization of Lithium Zirconium Silicate for CO2 Capture. Bulletin of Chemical Reaction Engineering & Catalysis, 9(3: 249-262. (doi:10.9767/bcrec.9.3.6646.249-262Permalink/DOI: http://dx.doi.org/10.9767/bcrec.9.3.6646.249-262

  4. LIWU Copper Plans to Get Listed

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    <正>According to recently-released "Notice con-cerning Environmental Protection Checks for IPO of Sichuan LIWU Copper Co., Ltd.", Sichuan LIWU Copper Co., Ltd. (hereinafter referred to as LIWU Copper) plans to issue 68 million shares, and all the funds raised will be

  5. Canine Models for Copper Homeostasis Disorders

    NARCIS (Netherlands)

    Wu, Xiaoyan; Leegwater, Peter A J|info:eu-repo/dai/nl/074236539; Fieten, Hille|info:eu-repo/dai/nl/314112596

    2016-01-01

    Copper is an essential trace nutrient metal involved in a multitude of cellular processes. Hereditary defects in copper metabolism result in disorders with a severe clinical course such as Wilson disease and Menkes disease. In Wilson disease, copper accumulation leads to liver cirrhosis and neurolog

  6. Extra-Hepatic Storage of Copper

    DEFF Research Database (Denmark)

    Heydorn, Kaj; Damsgaard, Else; Horn, N.

    1975-01-01

    The distribution of copper among the organs of an aborted, male foetus, expected to develop Menkes' syndrome, was entirely different from the distribution in 4 normal foetuses. Copper concentrations determined by neutron activation analysis showed a considerably reduced content in the liver......, but increased concentrations in the other organs analysed; total foetal copper was normal....

  7. Quanwei Copper Processing Base Put Into Operation

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    <正>Quanwei (Tongling) Copper Co.,Ltd’s copper processing base in Tongling of Anhui Province has been put into operation at the end of De- cember last year. It is reported that the copper processing project, invested by Zhengwei (Shenzhen) Technology

  8. Study on copper adsorption on olivine

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The copper adsorption on olivine supplied by A/S Olivine production plant at Aheim in western Norway has been studied. The factors which affect the uptake of copper have been evaluated. The results reveal that the equilibrium pH in aqueous solution has the greatest influence on the copper adsorption thanks to the competitive adsorption between proton and copper ions, and the adsorption of copper to olivine increases rapidly with the pH increasing from 4 to 6. The initial copper concentration and olivine dose also possess significant effect on copper adsorption. The adsorption efficieny of copper increases with the increase of olivine dose or the decrease of initial copper concentration at the same pH. The ionic strength effect on the adsorption has also been investigated, but it owns little effect on the adsorption process of copper due to the formation of inner sphere surface complexation of copper on olivine. The experimental data show that olivine has a high acid buffer capacity and is an effective adsorbent for copper.

  9. Canine Models for Copper Homeostasis Disorders

    NARCIS (Netherlands)

    Wu, Xiaoyan; Leegwater, Peter A J; Fieten, Hille

    2016-01-01

    Copper is an essential trace nutrient metal involved in a multitude of cellular processes. Hereditary defects in copper metabolism result in disorders with a severe clinical course such as Wilson disease and Menkes disease. In Wilson disease, copper accumulation leads to liver cirrhosis and neurolog

  10. Preparation of Copper-loaded Microcapsule Formulations

    Directory of Open Access Journals (Sweden)

    Nenad Jalšenjak

    2011-06-01

    Full Text Available Novel copper-loaded chitosan or chitosan/alginate based microcapsules formulations have been presented. It was shown that prolonged release of copper from microcapsules accompanied with possible prolonged presence of copper on leaves is useful in crop protection.

  11. Preparation of Copper-loaded Microcapsule Formulations

    Directory of Open Access Journals (Sweden)

    Nenad Jalšenjak

    2014-02-01

    Full Text Available Novel copper-loaded chitosan or chitosan/alginate based microcapsules formulations have been presented. It was shown that prolonged release of copper from microcapsules accompanied with possible prolonged presence of copper on leaves is useful in crop protection.

  12. Canine Models for Copper Homeostasis Disorders

    NARCIS (Netherlands)

    Wu, Xiaoyan; Leegwater, Peter A J; Fieten, Hille

    2016-01-01

    Copper is an essential trace nutrient metal involved in a multitude of cellular processes. Hereditary defects in copper metabolism result in disorders with a severe clinical course such as Wilson disease and Menkes disease. In Wilson disease, copper accumulation leads to liver cirrhosis and

  13. Copper coating specification for the RHIC arcs

    Energy Technology Data Exchange (ETDEWEB)

    Blaskiewicz, M.

    2010-12-01

    Copper coating specifications for the RHIC arcs are given. Various upgrade scenarios are considered and calculations of resistive wall losses in the arcs are used to constrain the necessary quality and surface thickness of a copper coating. We find that 10 {mu}m of high purity copper will suffice.

  14. Distribution of Copper in Rats Submitted to Treatment With Copper Aspirinate

    OpenAIRE

    LIU, Weiping; Yang, Yikun; Xiong, Huizhou; Lu, Ying; Yang, Rong

    1998-01-01

    The distribution of copper in Sprague – Dawley rats following a three month oral administration of 0,10 or 50mg/kg copper aspirinate has been investigated. Metal content was determined by ICP – AES in blood, brain, kidney, liver, lung, spleen, and dejection. The results show that treatment with copper aspirinate did not cause accumulation of copper in rats and excess ingested copper was excreted through feces.

  15. Chinalco Straightened Out Copper Assets, and Delegated Stock Equity of Yunnan Copper

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    <正>Immediately after the news that Chinalco transferred 58%stock equity of Yunnan Copper Group to its wholly-owned subsidiary China Copper Corporation Limited free of charge was disclosed on July 9,many individual investors couldn’t help but to think:Does it mean China Copper Corporation Limited will assemble assets for overall listing?At present,among main copper business companies under China Copper Corporation

  16. A copper vapor laser by using a copper-vapor-complex reaction at a low temperature

    OpenAIRE

    Kano, Toshiyuki; Taniguchi, Hiroshi; Saito, Hiroshi

    1987-01-01

    A copper vapor laser performance by using ametal-vapor-complex reaction (Cu+AlBr3) is reported. The laser operation is obtained at a low temperature without externalheating because of the AlBr3 vapors evaporating at a room temperature. The copper vapor laser using this metal-vapor-complex reaction has an advantage of deposition-free of a metallic copper to the laser tube wall, which is different from the copper halide and the organometallic copper lasers.

  17. Copper metabolism and copper-mediated alterations in the metabolism of cultured astrocytes

    OpenAIRE

    Scheiber, Ivo Florin

    2012-01-01

    Copper is an essential element that is required for a variety of important cellular functions. Since not only copper deficiency, but also excess of copper can seriously affect cellular functions, cellular copper metabolism is tightly regulated. Disturbances of copper homeostasis are the underlying defect of the inherited diseases Menkes and Wilson s disease and have also been linked to several neurodegenerative diseases including Alzheimer s disease and Parkinson s disease. Known astrocytes f...

  18. Carbonate Formation in Non-Aqueous Environments by Solid-Gas Carbonation of Silicates

    CERN Document Server

    Day, S J; Evans, A; Parker, J E

    2012-01-01

    We have produced synthetic analogues of cosmic silicates using the Sol Gel method, producing amorphous silicates of composition Mg(x)Ca(1-x)SiO3. Using synchrotron X-ray powder diffraction on Beamline I11 at the Diamond Light Source, together with a newly-commissioned gas cell, real-time powder diffraction scans have been taken of a range of silicates exposed to CO2 under non-ambient conditions. The SXPD is complemented by other techniques including Raman and Infrared Spectroscopy and SEM imaging.

  19. Oligo-lysine Induced Formation of Silica Particles in Neutral Silicate Solution

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Oligo-(lysine)n (n = 1-4) containing different numbers of lysine residues was used to induce the condensation of silicic acid to form silica particles in neutral silicate solution. It was found that the condensation rate and the formation of silica particles are dependent on the number of lysine residues in an oligo-lysine. Oligo-lysine with more lysine residues can link more silicic acid together to form a matrix that promotes the effective aggregation of the condensed silica pieces to form large silica particles.

  20. USE OF LOCAL NATURAL SILICEOUS RAW MATERIAL AND WASTES FOR PRODUCTION OF HEAT-INSULATING FOAMCONCRETE

    Directory of Open Access Journals (Sweden)

    V. U. Matsapulin

    2015-01-01

    Full Text Available The article analyzes the resource base, reserves and the use of siliceous rocks, their economic feasibility of the use for production of building materials of new generation with low-energy and other costs. Presented are the results of laboratory research and testing technology of production of insulating foam from a composition based on an aqueous solution of sodium silicate obtained from the local siliceous rocks (diatomite and the liquid alkali component - soapstock, hardener from ferrochrome slag and waste carbonate rock able to harden at a low temperature processing ( 100-110 ° C.

  1. Sorption properties of finely dispersed metal-containing polymer-silicate materials

    Directory of Open Access Journals (Sweden)

    Андрій Сергійович Масюк

    2015-11-01

    Full Text Available Sorption properties of metal-containing polymer-silicate materials on regarding to different acid-base indicators have been investigated. The effect of the nature of metal and polymer modifier (polyvinyl alcohol and polyvinylpyrrolidone on the amount of active centers and specific active surface area of such material was determined. Moisture absorption of modified and not modified silicate fillers was founded. The effect of Ni-containing polymer-silicate fillers on the speed of curing of polyester compositions was determined

  2. Carbonate formation in non-aqueous environments by solid-gas carbonation of silicates

    Science.gov (United States)

    Day, S. J.; Thompson, S. P.; Evans, A.; Parker, J. E.

    2012-02-01

    We have produced synthetic analogues of cosmic silicates using the Sol Gel method, producing amorphous silicates of composition Mg(x)Ca(1-x)SiO3. Using synchrotron X-ray powder diffraction on Beamline I11 at the Diamond Light Source, together with a newly-commissioned gas cell, real-time powder diffraction scans have been taken of a range of silicates exposed to CO2 under non-ambient conditions. The SXPD is complemented by other techniques including Raman and Infrared Spectroscopy and SEM imaging.

  3. The distribution of chromium among orthopyroxene, spinel and silicate liquid at atmospheric pressure

    Science.gov (United States)

    Barnes, S. J.

    1986-01-01

    The Cr distributions for a synthetic silicate melt equilibrated with bronzitic orthopyroxene and chromite spinel between 1334 and 1151 C over a range of oxygen fugacities between the nickel-nickel oxide and iron-wuestite buffers are studied. The occurrence, chemical composition, and structure of the orthopyroxene-silicate melt and the spinel-silicate melt are described. It is observed that the Cr content between bronzite and the melt increases with falling temperature along a given oxygen buffer and decreases with falling oxygen fugacity at a given temperature; however, the Cr content of the melt in equilibrium with spinel decreases with falling temperature and increases with lower oxygen fugacity.

  4. Electrochemical nucleation and growth of copper and copper alloys

    Science.gov (United States)

    Shao, Wenbo

    This dissertation aims to contribute to a fundamental understanding of the physicochemical processes occurring in electrochemical nucleation and growth. To this end, the effects of various anions (chloride (Cl-), sulfate (SO42-) and sulfamate (NH2SO 3-)) on the electrochemical kinetics and the mechanism of copper reduction, as well as on the microstructure of the resulting films, were studied. On the basis of this work, the deposition of copper alloys (Cu-Ag with positive heat of mixing, Cu-Au with negative heat of mixing) was investigated with the main objective to achieve an insight on the role of solid state thermodynamics on the electrocrystallization process. Chloride ions cause two competing effects: at low chloride concentration the formation of an adsorbed chloride layer introduces an additional reaction pathway, resulting in an overall depolarization of the reduction process with no significant change of the Tafel slope. At high chloride concentration, complexation phenomena induce a cathodic polarization of the deposition process and a decrease in the Tafel slope. Chlorides cause a decrease in the density and an increased size of copper nuclei. Sulfamate depolarizes copper reduction the most and results in the largest nucleus density. Chloride promotes the faceting, and dendritic growth of copper deposits along direction by introducing interfacial anisotropy. Addition of Ag in the solution or in the electrode substrate enhances copper deposition and results in an additional reduction peak. Codeposition of Cu-Ag increases nucleus density and decreases nucleus size. Such enhancement of copper deposition, the increase in nucleus density and the decrease in nucleus size by Ag could be due to the continued formation of a surface alloy of Cu-Ag and the fast interface dynamics of Ag deposition. Cu can be underpotentially codeposited in the Cu-Au alloy. Homogeneous solid solutions are grown under conditions of underpotential deposition of Cu, while precipitation

  5. Crystallisation mechanism of a multicomponent lithium alumino-silicate glass

    Energy Technology Data Exchange (ETDEWEB)

    Wurth, R. [Otto-Schott-Institut, Jena University, Fraunhoferstr. 6, 07743 Jena (Germany); Pascual, M.J., E-mail: mpascual@icv.csic.es [Instituto de Ceramica y Vidrio, CSIC, Kelsen 5, 28049 Madrid (Spain); Mather, G.C.; Pablos-Martin, A.; Munoz, F.; Duran, A. [Instituto de Ceramica y Vidrio, CSIC, Kelsen 5, 28049 Madrid (Spain); Cuello, G.J. [Institut Laue-Langevin, Boite Postale 156, 38042 Grenoble Cedex 9 (France); Ruessel, C. [Otto-Schott-Institut, Jena University, Fraunhoferstr. 6, 07743 Jena (Germany)

    2012-06-15

    A base glass of composition 3.5 Li{sub 2}O Bullet-Operator 0.15 Na{sub 2}O Bullet-Operator 0.2 K{sub 2}O Bullet-Operator 1.15 MgO Bullet-Operator 0.8 BaO Bullet-Operator 1.5 ZnO Bullet-Operator 20 Al{sub 2}O{sub 3} Bullet-Operator 67.2 SiO{sub 2} Bullet-Operator 2.6 TiO{sub 2} Bullet-Operator 1.7 ZrO{sub 2} Bullet-Operator 1.2 As{sub 2}O{sub 3} (in wt.%), melted and provided by SCHOTT AG (Mainz), was used to study the crystallisation mechanism of lithium alumino-silicate glass employing X-ray diffraction combined with neutron diffraction and non-isothermal differential scanning calorimetry (DSC). A high-quartz solid solution of LiAlSi{sub 2}O{sub 6} with nanoscaled crystals forms at 750 Degree-Sign C. Quantitative Rietveld refinement of samples annealed at 750 Degree-Sign C for 8 h determined a crystallised fraction of around 59 wt.%. The room temperature crystallised phase adopts an ordered, {beta}-eucryptite-like structure (2 Multiplication-Sign 2 Multiplication-Sign 2 cell) with Li ordered in the structural channels. The Avrami parameter (n {approx} 4), calculated from DSC data using different theoretical approaches, indicates that bulk crystallisation occurs and that the number of nuclei increases during annealing. The activation energy of the crystallisation is 531 {+-} 20 kJ mol{sup -1}. - Highlights: Black-Right-Pointing-Pointer Nanoscaled high-quartz crystals from a multicomponent lithium alumino-silicate glass. Black-Right-Pointing-Pointer Combined X-ray and neutron diffraction structural refinement. Black-Right-Pointing-Pointer {beta}-Eucryptite-like structure (2 Multiplication-Sign 2 Multiplication-Sign 2 cell) with Li ordered in the structural channels. Black-Right-Pointing-Pointer 3-Dimensional bulk crystallisation mechanism with an increasing number of nuclei. Black-Right-Pointing-Pointer Usage and validation of an alternative approach to calculate the Avrami parameter.

  6. Electrochemical behaviour of alkaline copper complexes

    Indian Academy of Sciences (India)

    C L Aravinda; S M Mayanna; V R Muralidharan

    2000-10-01

    A search for non-cyanide plating baths for copper resulted in the development of alkaline copper complex baths containing trisodium citrate [TSC] and triethanolamine [TEA]. Voltammetric studies were carried out on platinum to understand the electrochemical behaviour of these complexes. In TSC solutions, the deposition of copper involves the slow formation of a monovalent species. Adsorption of this species obeys Langmuir isotherm. In TEA solutions the deposition involves the formation of monovalent ions obeying the non-activated Temkin isotherm. Conversion of divalent to monovalent copper is also slow. In TEA and TSC alkaline copper solutions, the predominant species that undergo stepwise reduction contain only TEA ligands

  7. Crystallization of copper metaphosphate glass

    Science.gov (United States)

    Bae, Byeong-Soo; Weinberg, Michael C.

    1993-01-01

    The effect of the valence state of copper in copper metaphosphate glass on the crystallization behavior and glass transition temperature has been investigated. The crystallization of copper metaphosphate is initiated from the surface and its main crystalline phase is copper metaphosphate (Cu(PO)3),independent of the (Cu sup 2+)/(Cu(total)). However, the crystal morphology, the relative crystallization rates, and their temperature dependences are affected by the (Cu sup 2+)/(Cu (total)) ratio in the glass. On the other hand, the totally oxidized glass crystallizes from all over the surface. The relative crystallization rate of the reduced glass to the totally oxidized glass is large at low temperature, but small at high temperature. The glass transition temperature of the glass increases as the (Cu sup 2+)/(Cu(total)) ratio is raised. It is also found that the atmosphere used during heat treatment does not influence the crystallization of the reduced glass, except for the formation of a very thin CuO surface layer when heated in air.

  8. Spectroscopic studies of copper enzymes

    Energy Technology Data Exchange (ETDEWEB)

    Dooley, D.M.; Moog, R.; Zumft, W.; Koenig, S.H.; Scott, R.A.; Cote, C.E.; McGuirl, M.

    1986-05-01

    Several spectroscopic methods, including absorption, circular dichroism (CD), magnetic CD (MCD), X-ray absorption, resonance Raman, EPR, NMR, and quasi-elastic light-scattering spectroscopy, have been used to probe the structures of copper-containing amine oxidases, nitrite reductase, and nitrous oxide reductase. The basic goals are to determine the copper site structure, electronic properties, and to generate structure-reactivity correlations. Collectively, the results on the amine oxidases permit a detailed model for the Cu(II) sites in these enzymes to be constructed that, in turn, rationalizes the ligand-binding chemistry. Resonance Raman spectra of the phenylhydrazine and 2,4-dinitrophenyl-hydrazine derivatives of bovine plasma amine oxidase and models for its organic cofactor, e.g. pyridoxal, methoxatin, are most consistent with methoxatin being the intrinsic cofactor. The structure of the Cu(I) forms of the amine oxidases have been investigated by X-ray absorption spectroscopy (XAS); the copper coordination geometry is significantly different in the oxidized and reduced forms. Some anomalous properties of the amine oxidases in solution are explicable in terms of their reversible aggregation, which the authors have characterized via light scattering. Nitrite and nitrous oxide reductases display several novel spectral properties. The data suggest that new types of copper sites are present.

  9. Copper complexes as chemical nucleases

    Indian Academy of Sciences (India)

    Akhil R Chakravarty; Pattubala A N Reddy; Bidyut K Santra; Anitha M Thomas

    2002-08-01

    Redox active mononuclear and binuclear copper(II) complexes have been prepared and structurally characterized. The complexes have planar N-donor heterocyclic bases like 1,10-phenanthroline (phen), dipyridoquinoxaline (dpq) and dipyridophenazine (dppz) ligands that are suitable for intercalation to B-DNA. Complexes studied for nuclease activity have the formulations [Cu(dpq)2(H2O)] (ClO4)2.H2O (1), [{CuL(H2O)}2(-ox)](ClO4)2 (L = bpy, 2; phen, 3; dpq, 4; and dppz, 5) and [Cu(L)(salgly)] (L = bpy, 6; phen, 7; dpq, 8; and dppz, 9), where salgly is a tridentate Schiff base obtained from the condensation of glycine and salicylaldehyde. The dpq complexes are efficient DNA binding and cleavage active species. The dppz complexes show good binding ability but poor nuclease activity. The cleavage activity of the bis-dpq complex is significantly higher than the bis-phen complex of copper(II). The nuclease activity is found to be dependent on the intercalating nature of the complex and on the redox potential of the copper(II)/copper(I) couple. The ancillary ligand plays a significant role in binding and cleavage activity.

  10. Copper proteomes, phylogenetics and evolution.

    Science.gov (United States)

    Decaria, Leonardo; Bertini, Ivano; Williams, Robert J P

    2011-01-01

    This paper is a continuation of our study of the connection between the changing environment and the changing use of particular elements in organisms in the course of their combined evolution (Decaria, Bertini and Williams, Metallomics, 2010, 2, 706). Here we treat the changes in copper proteins in historically the same increasingly oxidising environmental conditions. The study is a bioinformatic analysis of the types and the numbers of copper domains of proteins from 435 DNA sequences of a wide range of organisms available in NCBI, using the method developed by Andreini, Bertini and Rosato in Accounts of Chemical Research 2009, 42, 1471. The copper domains of greatest interest are found predominantly in copper chaperones, homeostatic proteins and redox enzymes mainly used outside the cytoplasm which are in themselves somewhat diverse. The multiplicity of these proteins is strongly marked. The contrasting use of the iron and heme iron proteins in oxidations, mostly in the cytoplasm, is compared with them and with activity of zinc fingers during evolution. It is shown that evolution is a coordinated development of the chemistry of elements with use of novel and multiple copies of their proteins as their availability rises in the environment.

  11. CopperCore Service Integration

    Science.gov (United States)

    Vogten, Hubert; Martens, Harrie; Nadolski, Rob; Tattersall, Colin; van Rosmalen, Peter; Koper, Rob

    2007-01-01

    In an e-learning environment there is a need to integrate various e-learning services like assessment services, collaboration services, learning design services and communication services. In this article we present the design and implementation of a generic integrative service framework, called CopperCore Service Integration (CCSI). We will…

  12. Relationships between Basic and Silicic Magmatism in Continental Rift Settings: A Petrogeochemical Study of Carboniferous Post-collisional Rift Silicic Volcanics in Tianshan, NW China

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Petrogeochemical data are reported for silicic volcanic rocks from the Tianshan Carboniferous rift, with the aim of discussing the petrogenesis of silicic magmas. Incompatible element vs. incompatible element diagrams display smooth positive trends for the Tianshan Carboniferous rift-related volcanic rocks; the isotope ratios of the silicic lavas [87Sr/86Sr(t)=0.69988-0.70532; εNd(t)=4.76-8.00; 206Pb/204Pb(t)=17.435-18.017; 207Pb/204Pb(t)=15.438-15.509; 208Pb/204Pb(t) = 37.075-37.723] encompass those of the basic lavas. These data suggest a genetic link between rhyolites and basalts, but are not definitive in establishing whether silicic rocks are related to basalts through fractional crystallization or partial melting. Geochemical modeling of incompatible vs. compatible elements excludes the possibility that silicic melts are generated by the melting of basaltic rocks, and indicates a derivation by fractional crystallization plus moderate assimilation of wall rocks (AFC) starting from intermediate rocks to silicic rocks. Continuous AFC from basalt to rhyolite,with small rates of crustal assimilation, best explains the geochemical data. The presence or absence of bimodal volcanism (the "Daly Gap") might be related to cooling rates of magma chambers. In central and eastern Tianshan, the crust was thinner and the cooling rates of the magma chamber within the crust were greater. These conditions resulted in a rapid fall in temperature within the magma reservoir and caused a narrow temperature interval over which intermediate melts formed, effectively reducing the volume of the intermediate melts.

  13. MODIFICATION OF SURFACE LAYERS FOR SILICATE GLASSES BY ELECTRON IRRADIATION

    Directory of Open Access Journals (Sweden)

    V. S. Brunov

    2014-05-01

    Full Text Available Experimental research results of silicate glass surface layers modification by the influence of electron beams with 5-50 keV energies and 20-50 mC/cm2 doses are presented. It is shown that during the glasses exposure to an electron beam with 20-50 keV electron energies, a gradient optical waveguide with increased refractive index on waveguide axis Δn = 0.01-0.04 is formed in the surface layer. Сhemical etching rate is increased in the exposed area by up to two times which is related to glass grid destruction. Depending on irradiation dose thin film or silver nanoparticles with the size less than 20nm are formed on the surface of the silver containing glasses for electron energies less than 10 keV. Silver films drawn on the surface of the glass are dissolved into the glass bulk for electron energies 20-50 keV and 20-50 mC/cm2 dose. Basic mechanisms causing these effects are: chemical bonds breaking of spatial glass grid by high energy electrons, formation of negative volume charge inside the glass and field migration of positive metal ions into the volume charge region. Achieved results can be used in photonics, integral optics and nanoplasmonics device fabrication.

  14. Variations in Silicate Stardust: The Perils of Averages

    Science.gov (United States)

    Williams, Kyle

    2010-01-01

    Dust plays in important role in many astrophysical environments. Here we present a study of dust emanating from Asymptotic Giant Branch (AGB) stars, which are important because they are the principle contributors of dust to interstellar space. Dust around oxygen-rich AGB stars exhibit various infrared spectral features which have been classified according to their shape and peak position and are designated as SE1 through SE8. Here we concentrate on the SE8 class which is expected to exhibit the strongest 10 micron spectral feature, attributed to silicate dust, in order to determine how much the feature varies from star to star. For each individual spectrum the dust features were isolated by dividing by a blackbody continuum. The main characteristics of the 10 and 18 micron emission features were determined, including the peak height, peak wavelength, the full width half maximum, the baricenter, and the asymmetry of the feature. The peak position of the 10 micron feature varies enormously ( 9.4.-10.4 microns). We then sought any correlations between the spectral parameters in order to determine the causes of the variations. Very few correlations were found, indicating that the causes of variations of not simply explained. Using a simple radiative transfer modeling program (DUSTY) we produced synthetic spectra in order to determine how the physical parameters of the circumstellar shell produced such varied spectra.

  15. Formation of magnesium silicate hydrates (M-S-H)

    Science.gov (United States)

    Bernard, Ellina; Lothenbach, Barbara; Rentsch, Daniel; Pochard, Isabelle; Dauzères, Alexandre

    2017-06-01

    The formation of magnesium silicate hydrates (M-S-H) with MgO to SiO2 ratios from 0.7 to 1.6 has been studied at 20, 50 and 70 °C. TGA and XRD data reveal that initially brucite and M-S-H are formed while amorphous silica is still present as indicated by FT-IR and 29Si MAS NMR experiments. In this first step M-S-H with Mg/Si ∼1 with pH values ∼9.4 is formed independently of the total Mg/Si. Investigations by FT-IR and 29Si MAS NMR detail that the structure of that initial M-S-H evolved with time and M-S-H formed with Mg/Si ranging from ∼0.8 to ∼1.3 after 2 years at 20 °C and after 1 year at 50 and 70 °C. This implies that the composition of synthetic M-S-H depends strongly on temperature and equilibration time. At 50 and 70 °C the M-S-H formation occurs faster although it is thermodynamically slightly less stable. The solubility of M-S-H, talc and antigorite after 1 year or longer shows comparable trends.

  16. Combustion synthesis and photoluminescence study of silicate biomaterials

    Indian Academy of Sciences (India)

    V B Bhatkar; N V Bhatkar

    2011-10-01

    Silicate based bioceramics are promising candidates as biomaterials for tissue engineering. The combustion synthesis method provides control on the morphology and particle size of the synthesized material. This paper discusses the combustion synthesis of akermanite (Ca2MgSi2O7 and Sr2MgSi2O7), which has been shown to have good in vitro and in vivo bioactivities by earlier studies. Both Ca2MgSi2O7 and Sr2MgSi2O7 have akermanite structure. Ca2MgSi2O7 and Sr2MgSi2O7 were prepared using urea and ammonium nitrate. The combustion synthesis using urea and ammonium nitrate was found to be cost effective and efficient method of synthesis. The photoluminescence study of Ca2MgSi2O7 : Eu2+ and Sr2MgSi2O7 :Eu2+ shows host specific intense emission of Eu2+.

  17. Mechanical behavior of a composite interface: Calcium-silicate-hydrates

    Energy Technology Data Exchange (ETDEWEB)

    Palkovic, Steven D.; Moeini, Sina; Büyüköztürk, Oral, E-mail: obuyuk@mit.edu [Department of Civil and Environmental Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Yip, Sidney [Department of Nuclear Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)

    2015-07-21

    The generalized stacking fault (GSF) is a conceptual procedure historically used to assess shear behavior of defect-free crystalline structures through molecular dynamics or density functional theory simulations. We apply the GSF technique to the spatially and chemically complex quasi-layered structure of calcium-silicate-hydrates (C-S-H), the fundamental nanoscale binder within cementitious materials. A failure plane is enforced to calculate the shear traction-displacement response along a composite interface containing highly confined water molecules, hydroxyl groups, and calcium ions. GSF simulations are compared with affine (homogeneous) shear simulations, which allow strain to localize naturally in response to the local atomic environment. Comparison of strength and deformation behavior for the two loading methods shows the composite interface controls bulk shear deformation. Both models indicate the maximum shear strength of C-S-H exhibits a normal-stress dependency typical of cohesive-frictional materials. These findings suggest the applicability of GSF techniques to inhomogeneous structures and bonding environments, including other layered systems such as biological materials containing organic and inorganic interfaces.

  18. Preparation of calcium silicate absorbent from iron blast furnace slag.

    Science.gov (United States)

    Brodnax, L F; Rochelle, G T

    2000-09-01

    Calcium silicate hydrate (CSH) solids were prepared from hydrated lime and iron blast furnace slag in an aqueous agitated slurry at 92 degrees C. While it was hoped a minimal lime/slag ratio could be used to create near-amorphous CSH, the surface area of the product improved by increasing the lime/slag weight ratio to 2. The addition of gypsum to the lime/slag system dramatically improved the formation of surface area, creating solids with 139 m2/g after 30 hr of reaction when only a minimal amount of lime was present. The SO2 reactivity of solids prepared with gypsum greatly exceeded that of hydrated lime, achieving greater than 70-80% conversion of the alkalinity after 1 hr of reaction with SO2. The use of CaCl2 as an additive to the lime/slag system, in lieu of gypsum, also produced high-surface-area solids, 115 m2/g after 21 hr of reaction. However, the SO2 reactivity of these sorbents was relatively low given the high surface area. This emphasized that the correlation between surface area and SO2 reactivity was highly dependent on the solid phase, which was subsequently dependent on slurry composition.

  19. Zeta potentials in the flotation of oxide and silicate minerals.

    Science.gov (United States)

    Fuerstenau, D W; Pradip

    2005-06-30

    Adsorption of collectors and modifying reagents in the flotation of oxide and silicate minerals is controlled by the electrical double layer at the mineral-water interface. In systems where the collector is physically adsorbed, flotation with anionic or cationic collectors depends on the mineral surface being charged oppositely. Adjusting the pH of the system can enhance or prevent the flotation of a mineral. Thus, the point of zero charge (PZC) of the mineral is the most important property of a mineral in such systems. The length of the hydrocarbon chain of the collector is important because of chain-chain association enhances the adsorption once the surfactant ions aggregate to form hemimicelles at the surface. Strongly chemisorbing collectors are able to induce flotation even when collector and the mineral surface are charged similarly, but raising the pH sufficiently above the PZC can repel chemisorbing collectors from the mineral surface. Zeta potentials can be used to delineate interfacial phenomena in these various systems.

  20. Changes in Global Silicate Weathering Feedbacks over Phanerozoic Time

    Science.gov (United States)

    West, A. J.

    2015-12-01

    The release of carbon from the solid Earth exerts a first-order control on the evolution of the planetary environment. This basic climate forcing is modulated by a host of chemical reactions at the Earth's surface, the pace of which are in turn regulated by tectonic forces. Together, these various pieces in the puzzle of the global carbon cycle have been identified for decades, but understanding of how they fit together has remained elusive and continues to be much debated. In particular, we now know the climate-dependence of silicate mineral weathering may vary as a function of denudation rate, which is related to tectonic drivers. This variation suggests that the strength of the weathering feedback may have varied in the past, with consequent implications for the past state of global climate. This work will survey and synthesize approaches to representing changes in the weathering feedback, showing that relatively simple parameterizations yield similar results as recently developed reactive transport approaches. This similarity gives confidence in applying the simple parameterizations to reconstructing changes in feedback strength in the geologic past, at least over Phanerozoic timescales, and allows inclusion of this effect explicitly in carbon cycle models.

  1. Optical analysis of samarium doped sodium bismuth silicate glass

    Science.gov (United States)

    Thomas, V.; Sofin, R. G. S.; Allen, M.; Thomas, H.; Biju, P. R.; Jose, G.; Unnikrishnan, N. V.

    2017-01-01

    Samarium doped sodium bismuth silicate glass was synthesized using the melt quenching method. Detailed optical spectroscopic studies of the glassy material were carried out in the UV-Vis-NIR spectral range. Using the optical absorption spectra Judd-Ofelt (JO) parameters are derived. The calculated values of the JO parameters are utilized in evaluating the various radiative parameters such as electric dipole line strengths (Sed), radiative transition probabilities (Arad), radiative lifetimes (τrad), fluorescence branching ratios (β) and the integrated absorption cross- sections (σa) for stimulated emission from various excited states of Sm3 +‡ ion. The principal fluorescence transitions are identified by recording the fluorescence spectrum. Our analysis revealed that the novel glassy system has the optimum values for the key parameters viz. spectroscopic quality factor, optical gain, stimulated emission cross section and quantum efficiency, which are required for a high performance optical amplifier. Calculated chromaticity co-ordinates (0.61, 0.38) also confirm its application potential in display devices.

  2. Sintering and foaming of barium silicate glass powder compacts

    Science.gov (United States)

    Mueller, Ralf; Reinsch, Stefan; Agea-Blanco, Boris

    2016-10-01

    The manufacture of sintered glasses and glass-ceramics, glass matrix composites and glass-bounded ceramics or pastes is often affected by gas bubble formation. Against this background, we studied sintering and foaming of barium silicate glass powders used as SOFC sealants using different powder milling procedures. Sintering was measured by means of heating microscopy backed up by XPD, DTA, Vacuum Hot Extraction (VHE) and optical and electron microscopy. Foaming increased significantly as milling progressed. For moderately milled glass powders, subsequent storage in air could also promote foaming. Although the powder compacts were uniaxially pressed and sintered in air, the milling atmosphere sig¬ni¬ficantly affected foaming. The strength of this effect increased in the order Ar ? N2 encapsulated CO2, even for powders milled in Ar and N2. Results of this study thus indicate that foaming is caused by carbonaceous species trapped on the glass powder surface. Foaming could be substantially reduced by milling in water and 10 wt% HCl.

  3. Silicate grout curtains behaviour for the protection of coastal aquifers

    Energy Technology Data Exchange (ETDEWEB)

    Elektorowicz, M.; Chifrina, R.; Hesnawi, R. [Concordia Univ., Montreal, Quebec (Canada)

    1997-12-31

    Tests were performed to evaluate the behaviour of silicate grout with different reagents (ethylacetate - formamide SA and calcium chloride SC) in pure silica sand and natural soils from coastal areas containing organic matter, clayey soil and silica sand. The grouted specimens were tested with simulated fresh and salt water. The setting process during chemical grouting in the soil and sand was studied. The grouting of soil and sand with SA caused a transfer to the environment of some compounds: sodium formate, sodium acetate, ammonia and part of the initial ethylacetate and formamide. This process had a tendency to decrease for approximately 4 months. The stability of specimens was low. The grouting of soil and sand with SC caused no significant contamination of the environment. The increase of pH of environmental water was even less than with SA grouting. Also, the stability of specimens is higher in comparison with SA grouting. Salt water protected the specimens grouted with SA and SC from destruction and prevented contamination.

  4. Sintering and foaming of barium silicate glass powder compacts

    Directory of Open Access Journals (Sweden)

    Ralf Mueller

    2016-10-01

    Full Text Available The manufacture of sintered glasses and glass-ceramics, glass matrix composites and glass-bounded ceramics or pastes is often affected by gas bubble formation. Against this background, we studied sintering and foaming of barium silicate glass powders used as SOFC sealants using different powder milling procedures. Sintering was measured by means of heating microscopy backed up by XPD, DTA, Vacuum Hot Extraction (VHE and optical and electron microscopy. Foaming increased significantly as milling progressed. For moderately milled glass powders, subsequent storage in air could also promote foaming. Although the powder compacts were uniaxially pressed and sintered in air, the milling atmosphere sig¬ni¬ficantly affected foaming. The strength of this effect increased in the order Ar  N2 < air < CO2. Conformingly, VHE studies revealed that the pores of foamed samples predominantly encapsulated CO2, even for powders milled in Ar and N2. Results of this study thus indicate that foaming is caused by carbonaceous species trapped on the glass powder surface. Foaming could be substantially reduced by milling in water and 10 wt% HCl.

  5. Restriction of gas coning by polymer/silicate well treatment

    Energy Technology Data Exchange (ETDEWEB)

    Lakatos, I.; Lakatos-Szabo, J. (Research Laboratory for Mining Chemistry, Hungarian Academy of Science, Miskolc-Egyetemvaros (HU)); Kristof, M.; Tromboczky, S.; Bodola, M.; Munkacsi, I. (Nagyalfold Oil and Gas Production Comp., Szolnok (HU))

    1991-01-01

    The laboratory and field studies were focussed on development of a well treatment technology which can be used for restriction of gas coning in the Algyo reservoir. The chemical system is a modified version of an earlier method based on simultaneous gelation of polymers and silicates. That technique has already been routinely and successfully applied for stimulation of oil producing wells in the same field. Extensive laboratory studies were carried out to tailor the original receipt to the field conditions. Special attention was paid to the placement technology. Two-point injection regime was elaborated to develop a horizontal barrier between the oil and gas bearing zones. The field tests have definitely shown that the efficiency of gas blocking primarily depends on extension of the shading area formed over the active perforation, and even though special measures were taken to reduce gravitational segregation, the efficiency of gas blocking is usually worse than the improvement of production characteristics in vertical profile correction used for water blocking. 5 refs., 10 figs., 4 tabs.

  6. Chemical interactions and configurational disorder in silicate melts

    Directory of Open Access Journals (Sweden)

    G. Ottonello

    2005-06-01

    Full Text Available The Thermodynamics of quasi-chemical and polymeric models are briefly reviewed. It is shown that the two classes are mutually consistent, and that opportune conversion of the existing quasi-chemical parameterization of binary interactions in MO-SiO2 joins to polymeric models may be afforded without substantial loss of precision. It is then shown that polymeric models are extremely useful in deciphering the structural and reactive properties of silicate melts and glasses. They not only allow the Lux-Flood character of the dissolved oxides to be established, but also discriminate subordinate strain energy contributions to the Gibbs free energy of mixing from the dominant chemical interaction terms. This discrimination means that important information on the short-, medium- and long-range periodicity of this class of substances can be retrieved from thermodynamic analysis. Lastly, it is suggested that an important step forward in deciphering the complex topology of the inhomogeneity ranges observed at high SiO2 content can be performed by applying SCMF theory and, particularly, Matsen-Schick spectral analysis, hitherto applied only to rubberlike materials.

  7. O-17 NMR studies of some silicate crystals and glasses

    CERN Document Server

    Yildirim, E K

    2000-01-01

    structure. Therefore some of the Sn has to be in three coordinated to oxygen for charge balancing. The sup 1 sup 7 O MAS NMR spectra of a partially crystallised sample showed three distinct sites which are assigned as Sn-O-Sn, Si-O-Sn, and Si-O-Si on the basis of their chemical shift. The C sub Q values obtained from the simulations of these peaks supports this assignment. The sup 2 sup 9 Si MAS NMR of the same sample showed two crystalline and a glassy peaks which are fitted to two crystalline and two glassy sites. The possible composition of this sample was calculated and found to be SiSn sub 8 O sub 1 sub 0. Crystalline and glassy silicates were investigated by means of sup 1 sup 7 O NMR. The dependence of the measured efg on the Si-O-AI bond angle was investigated in some crystalline aluminosilicate sodalites and kalsilite. The results show that C sub Q increases with increasing bond angle while eta decreases with increasing bond angle and they both follow a similar function to that found for the Si-O-Si ...

  8. The role of silicate surfaces on calcite precipitation kinetics

    DEFF Research Database (Denmark)

    Stockmann, Gabrielle J.; Wolff-Boenisch, Domenik; Bovet, Nicolas Emile

    2014-01-01

    The aim of this study is to illuminate how calcite precipitation depends on the identity and structure of the growth substrate. Calcite was precipitated at 25°C from supersaturated aqueous solutions in the presence of seeds of either calcite or one of six silicate materials: augite, enstatite......, labradorite, olivine, basaltic glass and peridotite rock. Calcite saturation was achieved by mixing a CaCl2-rich aqueous solution with a NaHCO3-Na2CO3 aqueous buffer in mixed-flow reactors containing 0.5-2g of mineral, rock, or glass seeds. This led to an inlet fluid calcite saturation index of 0.6 and a p......H equal to 9.1. Although the inlet fluid composition, flow rate, and temperature were identical for all experiments, the onset of calcite precipitation depended on the identity of the seeds present in the reactor. Calcite precipitated instantaneously and at a constant rate in the presence of calcite...

  9. Structure characterization for the geopolymer of sodium silicate and metakaolin

    Institute of Scientific and Technical Information of China (English)

    CAO De-guang; SU Da-gen

    2005-01-01

    Geopolymers of metakaolin and sodium silicate were synthesized respectively with the ratios of the amount of SiO2 in the sodium silica solution to that of Al2O3 in metakaolinite equal to 1.0, and 0.66. The geopolymeric structures of the products were investigated by 27Al and 29Si solid-state nuclear magnetic resonances with magic-angle spinning (MAS NMR), Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), differential scanning colorimetry (DSC) and scanning electron microscopy (SEM). The reaction of the Al-O sheet in meakaolinite with low-order polymerized Si-O tetrahedral units such as monomer of SiO4 yields three-dimensional structures with the Q3 Si-O tetrahedral structure and the coordination of Al(IV) in the Al-O tetrahedral structure. The geopolymers are essentially X-ray amorphous. The assays by 27Al and 29Si NMR, FTIR confirm that the active structure in the metakaolinite is the sheet of Al-O with three coordination states.

  10. Silicate features in Galactic and extragalactic post-AGB discs

    CERN Document Server

    Gielen, C; Van Winckel, H; Evans, T Lloyd; Woods, P M; Kemper, F; Marengo, M; Meixner, M; Sloan, G C; Tielens, A G G M

    2011-01-01

    Aims. In this paper we study the Spitzer and TIMMI2 infrared spectra of post-AGB disc sources, both in the Galaxy and the LMC. Using the observed infrared spectra we determine the mineralogy and dust parameters of the discs, and look for possible differences between the Galactic and extragalactic sources. Methods. Modelling the full spectral range observed allows us to determine the dust species present in the disc and different physical parameters such as grain sizes, dust abundance ratios, and the dust and continuum temperatures. Results. We find that all the discs are dominated by emission features of crystalline and amorphous silicate dust. Only a few sample sources show features due to CO2 gas or carbonaceous molecules such as PAHs and C60 fullerenes. Our analysis shows that dust grain processing in these discs is strong, resulting in large average grain sizes and a very high crystallinity fraction. However, we do not find any correlations between the derived dust parameters and properties of the central...

  11. Characterization of a silicate glass as a high dose dosimeter

    Energy Technology Data Exchange (ETDEWEB)

    Farah, K., E-mail: k.farah@cnstn.rnrt.t [Laboratoire de Radiotraitement. Centre National des Sciences et Technologie Nucleaires, 2020 Sidi-Thabet (Tunisia); Mejri, A.; Hosni, F. [Laboratoire de Radiotraitement. Centre National des Sciences et Technologie Nucleaires, 2020 Sidi-Thabet (Tunisia); Ben Ouada, H. [Laboratoire de Physique et Chimie des Interfaces, Faculte des Sciences de Monastir, 5000 Monastir (Tunisia); Fuochi, P.G.; Lavalle, M. [ISOF-CNR, Via P. Gobetti 101, 40129 Bologna (Italy); Kovacs, A. [Institute of Isotopes, HAS, P.O. Box 77, H-1525 Budapest (Hungary)

    2010-02-21

    Commercial silicate glass has been investigated as a possible high dose dosimeter using an UV-vis spectrophotometer. Glass samples were irradiated by {sup 60}Co gamma rays and the results compared with those obtained with 3.4 and 8.4 MeV electron beams. The irradiated samples showed rapid fading at room temperature immediately after irradiation. In order to improve the stability of absorbance, glass samples were submitted to post-irradiation thermal treatments (150 deg. C for 20 min). The influences of the dose, type and energy of the ionizing radiation on the fading characteristics and on the response of the irradiated and thermally treated glasses were studied. Dependence of the glass response on the temperature during gamma irradiation in the range -3 to 80 deg. C is reported. The reproducibility to reuse glass dosimeter by thermal bleaching the radiation induced colour centres at 300 deg. C for 30 min was also investigated. Calibration curves in the range 0.1-17 kGy were obtained by using in-plant calibration techniques against transfer standard alanine dosimeters in the Tunisian semi-industrial gamma irradiation facility.

  12. STRUCTURE AND CHARACTERIZATION OF SOME HIGH CHEMICALLY RESISTANCE SILICATE GLASSES

    Directory of Open Access Journals (Sweden)

    H.A. Abo-Mosallam

    2016-10-01

    Full Text Available A multi component silicate glasses based on Li₂O-MgO-P₂O₅-SiO₂ system were synthesized and modified by Na₂O /Li₂O, SrO /MgO and CaO /SrO replacements. The prepared glasses have been characterized by X-ray Diffraction (XRD and Fourier Transform Infrared Spectroscopy (FTIR. Additionally, bulk density, microhardness, chemical durability and in vitro bioactivity were evaluated as a function of introducing different alkali and alkaline element substitutions. For comprehension the in vitro bioactivity, the glass samples were soaking in simulated body fluid (SBF solution at 37°C for 14 days. Scanning electron microscopy coupled with energy-dispersive X-ray (SEM-EDX and (FTIR were used to characterize forming hydroxyapatite layer produced on glass specimen surfaces. The results show that Na₂O/Li₂O and CaO/SrO replacements led to enhance the bioactivity behavior of the glasses. The results are harmonious with a weaker network glass structure consequence of Na₂O/Li₂O and SrO/MgO replacement in the glasses. However, the glass network connectivity increased with addition of the higher charge to size ratio of Ca2+ instead of Sr2+. The prepared glass samples had microhardness in the range, 4920-6017 MPa; density values in the range, 2.46-2.78 g/cm³ and the weight loss percent was ranged between 0.72 and 1.67 %.

  13. Leaf application of silicic acid to white oat and wheat

    Directory of Open Access Journals (Sweden)

    Rogério Peres Soratto

    2012-11-01

    Full Text Available Silicon (Si is beneficial to plants in several aspects, but there are doubts about the effectiveness of leaf application. The purpose of this work was to evaluate the effects of Si, applied in a newly developed stabilized silicic acid form to the leaf, on nutrition and yield of irrigated white oat and wheat. Two experiments were performed (one per crop in winter 2008, in Botucatu-SP, Brazil. A completely randomized block design with 14 replications was used. Treatments consisted of a control (without Si application and Si leaf spraying, at a rate of 2.0 L ha-1 of the commercial product containing 0.8 % soluble Si. Silicon rate was divided in three parts, i.e. applications at tillering, floral differentiation and booting stages. Silicon leaf application increased N, P, K, and Si concentrations in white oat flag leaf, resulting in higher shoot dry matter, number of panicles per m², number of grains per panicle and grain yield increase of 34 %. In wheat, Si leaf application increased K and Si concentrations, shoot dry matter and number of spikes per m², resulting in a grain yield increase of 26.9 %.

  14. Apatite bone cement reinforced with calcium silicate fibers.

    Science.gov (United States)

    Motisuke, Mariana; Santos, Verônica R; Bazanini, Naiana C; Bertran, Celso A

    2014-10-01

    Several research efforts have been made in the attempt to reinforce calcium phosphate cements (CPCs) with polymeric and carbon fibers. Due to their low compatibility with the cement matrix, results were not satisfactory. In this context, calcium silicate fibers (CaSiO3) may be an alternative material to overcome the main drawback of reinforced CPCs since, despite of their good mechanical properties, they may interact chemically with the CPC matrix. In this work CaSiO3 fibers, with aspect ratio of 9.6, were synthesized by a reactive molten salt synthesis and used as reinforcement in apatite cement. 5 wt.% of reinforcement addition has increased the compressive strength of the CPC by 250% (from 14.5 to 50.4 MPa) without preventing the cement to set. Ca and Si release in samples containing fibers could be explained by CaSiO3 partial hydrolysis which leads to a quick increase in Ca concentration and in silica gel precipitation. The latter may be responsible for apatite precipitation in needle like form during cement setting reaction. The material developed presents potential properties to be employed in bone repair treatment.

  15. Quaternary ammonium borohydride adsorption in mesoporous silicate MCM-48

    Energy Technology Data Exchange (ETDEWEB)

    Wolverton, Michael J [Los Alamos National Laboratory; Daemen, Luke L [Los Alamos National Laboratory; Hartl, Monika A [Los Alamos National Laboratory

    2010-01-01

    Inorganic borohydrides have a high gravimetric hydrogen density but release H2 only under energetically unfavorable conditions. Surface chemistry may help in lowering thermodynamic barriers, but inclusion of inorganic borohydrides in porous silica materials has proved hitherto difficult or impossible. We show that borohydrides with a large organic cation are readily adsorbed inside mesoporous silicates, particularly after surface treatment. Thermal analysis reveals that the decomposition thermodynamics of tetraalkylammonium borohydrides are substantially affected by inclusion in MCM-48. Inelastic neutron scattering (INS) data show that the compounds adsorb on the silica surface. Evidence of pore loading is supplemented by DSC/TGA, XRD, FTIR, and BET isotherm measurements. Mass spectrometry shows significant hydrogen release at lower temperature from adsorbed borohydrides in comparison with the bulk borohydrides. INS data measured for partially decomposed samples indicates that the decomposition of the cation and anion is likely simultaneous. Additionally, these data confirm the formation of Si-H bonds on the silica surface upon decomposition of adsorbed tetramethylammonium borohydride.

  16. Mesoporous Calcium Silicate Nanoparticles with Drug Delivery and Odontogenesis Properties.

    Science.gov (United States)

    Huang, Ching-Yuang; Huang, Tsui-Hsien; Kao, Chia-Tze; Wu, Yuan-Haw; Chen, Wan-Chen; Shie, Ming-You

    2017-01-01

    Calcium silicate (CS) -based materials play an important role in the development of endodontic materials that induce bone/cementum tissue regeneration and inhibit bacterial viability. The aim of this study was to prepare novel mesoporous CS (MesoCS) nanoparticles that have osteogenic, drug delivery, and antibacterial characteristics for endodontic materials and also have an excellent ability to develop apatite mineralization. The MesoCS nanoparticles were prepared using sol-gel methods. In addition, the mesoporous structure, specific surface area, pore volume, and morphology of the MesoCS nanoparticles were analyzed. The apatite mineralization ability, in vitro odontogenic differentiation, drug delivery, and antibacterial properties of the MesoCS nanoparticles were further investigated. The results indicate that the 200-nm-sized MesoCS nanoparticles synthesized using a facile template method exhibited a high specific surface area and pore volume with internal mesopores (average pore size = 3.05 nm). Furthermore, the MesoCS nanoparticles can be used as drug carriers to maintain sustained release of gentamicin and fibroblast growth factor-2 (FGF-2). The MesoCS-loaded FGF-2 might stimulate more odontogenic-related protein than CS because of the FGF-2 release. Based on this work, it can be inferred that MesoCS nanoparticles are potentially useful endodontic materials for biocompatible and osteogenic dental pulp tissue regenerative materials. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  17. A New Biphasic Dicalcium Silicate Bone Cement Implant

    Directory of Open Access Journals (Sweden)

    Fausto Zuleta

    2017-07-01

    Full Text Available This study aimed to investigate the processing parameters and biocompatibility of a novel biphasic dicalcium silicate (C2S cement. Biphasic α´L + β-C2Sss was synthesized by solid-state processing, and was used as a raw material to prepare the cement. In vitro bioactivity and biocompatibility studies were assessed by soaking the cement samples in simulated body fluid (SBF and human adipose stem cell cultures. Two critical-sized defects of 6 mm Ø were created in 15 NZ tibias. A porous cement made of the high temperature forms of C2S, with a low phosphorous substitution level, was produced. An apatite-like layer covered the cement’s surface after soaking in SBF. The cell attachment test showed that α´L + β-C2Sss supported cells sticking and spreading after 24 h of culture. The cement paste (55.86 ± 0.23 obtained higher bone-to-implant contact (BIC percentage values (better quality, closer contact in the histomorphometric analysis, and defect closure was significant compared to the control group (plastic. The residual material volume of the porous cement was 35.42 ± 2.08% of the initial value. The highest BIC and bone formation percentages were obtained on day 60. These results suggest that the cement paste is advantageous for initial bone regeneration.

  18. Efficacy of dispersion of magnesium silicate (talc in papermaking

    Directory of Open Access Journals (Sweden)

    Vipul Singh Chauhan

    2017-02-01

    Full Text Available The understanding of the dispersion chemistry of papermaking grade fillers is as important as their effect on paper. Magnesium silicate (talc is one of the major fillers used for papermaking. It is hydrophobic and chemically inert. The dispersion chemistry of talc of different particle sizes was studied with wetting agent (non-ionic triblock copolymer and anionic dispersant (sodium salt of polyacrylic acid. Both wetting agent and dispersant were added in talc slurry separately and in combination. The dispersion behavior was studied through measuring the Brookfield viscosity. The wetted and dispersed talc was also added to paper to understand its effect on papermaking process and paper properties. Wetting and dispersion changed the colloidal charge chemistry of talc making it more anionic which reduced the talc retention in paper. Lowering the particle size of talc significantly improved the light scattering coefficient (LSC of paper and decreased its retention. Controlling colloidal charge of papermaking suspension with cationic polyacrylamide polymer helped in protecting the retention of talc without affecting the LSC of both filler and paper.

  19. Arginine Silicate Inositol Complex Accelerates Cutaneous Wound Healing.

    Science.gov (United States)

    Durmus, Ali Said; Tuzcu, Mehmet; Ozdemir, Oguzhan; Orhan, Cemal; Sahin, Nurhan; Ozercan, Ibrahim Hanifi; Komorowski, James Richard; Ali, Shakir; Sahin, Kazim

    2016-10-14

    Arginine silicate inositol (ASI) complex is a composition of arginine, silicon, and inositol that has been shown to have beneficial effects on vascular health. This study reports the effects of an ASI ointment on wound healing in rats. A full-thickness excision wound was created by using a disposable 5 mm diameter skin punch biopsy tool. In this placebo-controlled study, the treatment group's wound areas were covered by 4 or 10 % ASI ointments twice a day for 5, 10, or 15 days. The rats were sacrificed either 5, 10, or 15 days after the wounds were created, and biopsy samples were taken for biochemical and histopathological analysis. Granulation tissue appeared significantly faster in the ASI-treated groups than in the control groups (P B cells (NF-κB), and various cytokines (TNF-α and IL-1β) measured in this study showed a significant fall in expression level in ASI-treated wounds. The results suggest that topical application of ASI ointment (especially 4 % concentration) has beneficial effects on the healing response of an excisional wound.

  20. Reactivity test between beryllium and copper

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, H. [Japan Atomic Energy Research Institute, Ibaraki-ken (Japan); Kato, M. [NGK Insulators, Ltd., Aichi-ken (Japan)

    1995-09-01

    Beryllium has been expected for using as plasma facing material on ITER. And, copper alloy has been proposed as heat sink material behind plasma facing components. Therefore, both materials must be joined. However, the elementary process of reaction between beryllium and copper alloy does not clear in detail. For example, other authors reported that beryllium reacted with copper at high temperature, but it was not obvious about the generation of reaction products and increasing of the reaction layer. In the present work, from this point, for clarifying the elementary process of reaction between beryllium and copper, the out-of-pile compatibility tests were conducted with diffusion couples of beryllium and copper which were inserted in the capsule filled with high purity helium gas (6N). Annealing temperatures were 300, 400, 500, 600 and 700{degrees}C, and annealing periods were 100, 300 and 1000h. Beryllium specimens were hot pressed beryllium, and copper specimens were OFC (Oxygen Free Copper).

  1. Friction stir welding of copper alloys

    Institute of Scientific and Technical Information of China (English)

    Liu Shuhua; Liu Meng; Wang Deqing; Xu Zhenyue

    2007-01-01

    Copper plates,brass plates and copper/brass plates were friction stir welded with various parameters. Experimental results show that the microstructure of the weld is characterized by its much finer grains as contrasted with the coarse grains of parent materials and the heat-affected zones are very narrow. The microhardness of the copper weld is a little higher than that of parent plate. The microhardness of brass weld is about 25% higher than that of parent material. The tensile strength of copper joints increases with increasing welding speed in the test range. The range of parameters to obtain good welds for copper is much wider than that for brass. When different materials were welded, the position of copper plate before welding affected the quality of FSW joints. If the copper plate was put on the advancing side of weld, the good quality of weld could be got under proper parameters.

  2. Catastrophic Oxidation of Copper: A Brief Review

    Science.gov (United States)

    Belousov, V. V.; Klimashin, A. A.

    2012-10-01

    A brief review of the current understanding of copper accelerated oxidation in the presence of low-melting oxides (Bi2O3, MoO3, and V2O5) is given. Special attention is paid to the kinetics, thermodynamics, and mechanisms of accelerated oxidation of copper. The mechanisms of two stages (fast and superfast) of the copper accelerated oxidation are considered. It is shown that the fast oxidation of copper occurs by a diffusion mechanism. Oxygen diffusion along the liquid channels in the oxide scale is the rate-limiting step in the overall mechanism. The superfast oxidation of copper occurs by a fluxing mechanism. Realization of the particular mechanism depends on the mass ratio of low-melting oxide to the metal. The mass ratios of low-melting oxide to the metal and the oxygen partial pressures for superfast oxidation of copper are established. A model of the fast oxidation of copper is discussed.

  3. Process Of Bonding Copper And Tungsten

    Science.gov (United States)

    Slattery, Kevin T.; Driemeyer, Daniel E.

    1999-11-23

    Process for bonding a copper substrate to a tungsten substrate by providing a thin metallic adhesion promoting film bonded to a tungsten substrate and a functionally graded material (FGM) interlayer bonding the thin metallic adhesion promoting film to the copper substrate. The FGM interlayer is formed by thermal plasma spraying mixtures of copper powder and tungsten powder in a varied blending ratio such that the blending ratio of the copper powder and the tungsten powder that is fed to a plasma torch is intermittently adjusted to provide progressively higher copper content/tungsten content, by volume, ratio values in the interlayer in a lineal direction extending from the tungsten substrate towards the copper substrate. The resulting copper to tungsten joint well accommodates the difference in the coefficient of thermal expansion of the materials.

  4. Carbonation of metal silicates for long-term CO.sub.2 sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Blencoe, James G.; Palmer, Donald A.; Anovitz, Lawrence M.; Beard, James S.

    2017-08-01

    In a preferred embodiment, the invention relates to a process of sequestering carbon dioxide. The process comprises the steps of: (a) reacting a metal silicate with a caustic alkali-metal hydroxide to produce a hydroxide of the metal formerly contained in the silicate; (b) reacting carbon dioxide with at least one of a caustic alkali-metal hydroxide and an alkali-metal silicate to produce at least one of an alkali-metal carbonate and an alkali-metal bicarbonate; and (c) reacting the metal hydroxide product of step (a) with at least one of the alkali-metal carbonate and the alkali-metal bicarbonate produced in step (b) to produce a carbonate of the metal formerly contained in the metal silicate of step (a).

  5. Polymer Derived Rare Earth Silicate Nanocomposite Protective Coatings for Nuclear Thermal Propulsion Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this Phase I SBIR program is to develop polymer derived rare earth silicate nanocomposite environmental barrier coatings (EBC) for providing...

  6. Polymer Derived Yttrium Silicate Ablative TPS Materials for Next-Generation Exploration Missions Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Through the proposed NASA SBIR program, NanoSonic will optimize its HybridSil® derived yttrium silicates to serve as next-generation reinforcement for carbon...

  7. Some observations on use of siliceous mineral waters in reduction of corrosion in RCC structures

    Digital Repository Service at National Institute of Oceanography (India)

    Venugopal, C.

    The corrosion-resisting characteristics of reinforcement in cement blended with siliceous mineral wastes viz. gold tailing and flyash have been evaluated by using an accelerated corrosion technique. The additions of these mineral admixtures...

  8. Observations on the morphological diversity and distribution of two siliceous nannoplankton genera, Hyalolithus and Petasaria

    DEFF Research Database (Denmark)

    Jordan, Richard W.; Abe, Kent; Cruz, Jarret

    2016-01-01

    Scale-bearing siliceous nannoplankton are occasionally encountered in surface seawater samples, but are rarely identified or illustrated. In this study, the morphological diversity of the haptophyte Hyalolithus neolepis and the enigmatic Petasaria heterolepis are investigated in scanning and tran...

  9. Geotechnical properties of two siliceous cores from the central Indian Ocean

    Digital Repository Service at National Institute of Oceanography (India)

    Khadge, N.H.

    Physical properties of the siliceous sediments from the Central Indian Basin are measured on two short cores. The properties such as water content, Atterberg limits, porosity specific gravity, wet density show the medium to high plastic sediment...

  10. Characterization of Electrochemical and Morphological Properties of Iron-Phosphate-Silicate Chemical Garden Structures

    Science.gov (United States)

    Doloboff, I. J.; Barge, L. M.; Russell, M. J.; Kanik, I.

    2012-03-01

    Examination of the growth of Fe^2^+, phosphate, and silicate chemical garden structures to understand properties of similar structures that may have formed at Hadean alkaline hydrothermal vents which may play an important role in the emergence of life.

  11. Cementing properties of steel slag activated by sodium silicates and sodium hydroxide

    Institute of Scientific and Technical Information of China (English)

    Wen Ni; En Wang; Jianping Li; Han Sun

    2005-01-01

    Steel slag which is mainly composed of γ-CasSiO4 and other silicates or alumino-silicates is activated by sodium silicates and sodium hydroxide. The powders of such steel slag are usually inert to hydrate and subsequently have very low ability of cementing. But when sodium silicates and sodium hydroxide are used as activators the steel slag shows very good properties of cementing. When activated with NaOH solution the hardened slurry of the steel slag has a compressive strength of 11.13 MPa after being cured for 28 days. When activated with Na2SiO3 solution the samples after being cured for 28 days have an average compressive strength of 40.23 MPa. While the steel slag slurry which is only mixed with water has a compressive of 0.88 MPa after being cured for 28 days.

  12. Turbulent metal-silicate mixing, fragmentation, and equilibration in magma oceans

    CERN Document Server

    Deguen, Renaud; Olson, Peter

    2014-01-01

    Much of the Earth was built by high-energy impacts of planetesimals and embryos, many of these impactors already differentiated, with metallic cores of their own. Geochemical data provide critical information on the timing of accretion and the prevailing physical conditions, but their interpretation depends critically on the degree of metal-silicate chemical equilibration during core-mantle differentiation, which is poorly constrained. Efficient equilibration requires that the large volumes of iron derived from impactor cores mix with molten silicates down to scales small enough to allow fast metal-silicate mass transfer. Here we use fluid dynamics experiments to show that large metal blobs falling in a magma ocean mix with the molten silicate through turbulent entrainment, with fragmentation into droplets eventually resulting from the entrainment process. In our experiments, fragmentation of the dense fluid occurs after falling a distance equal to 3-4 times its initial diameter, at which point a sizable volu...

  13. Elastic and anelastic anomalies in (Ca,Sr)TiO perovskites: Analogue behaviour for silicate perovskites

    OpenAIRE

    Walsh, J.W.; Taylor, P.A.; Buckley, A.; Darling, T.W.; Schreuer, J.; Carpenter, M.A.

    2008-01-01

    Elastic and anelastic anomalies in (Ca,Sr)TiO3 perovskites: Analogue behaviour for silicate perovskites UNITED KINGDOM (Walsh, J.W.) UNITED KINGDOM Received: 2007-10-30 Revised: 2008-02-18 Accepted: 2008-02-27

  14. Design of TiO2-loaded Porous Siliceous Materials and Application to Photocatalytic Environmental Purification

    National Research Council Canada - National Science Library

    KAMEGAWA, Takashi; KUWAHARA, Yasutaka; YAMASHITA, Hiromi

    2016-01-01

    ... with additional functions. This review mainly describes our recent investigations on the design of TiO2-loaded porous siliceous materials for application to photocatalytic environmental purification via efficient adsorption...

  15. Synthesis of Calcium Silicate (Casio3) Using Calcium Fluoride, Quartz and Microbes

    National Research Council Canada - National Science Library

    B. Gopal Krishna; M. Jagannadha Rao

    2015-01-01

    .... In this paper, synthesis of calcium silicate (CaSiO3) using calcium fluoride (CaF2) and quartz (SiO2) under microbial environment in a laboratory is being adopted to produce the required material...

  16. Polymer Derived Rare Earth Silicate Nanocomposite Protective Coatings for Nuclear Thermal Propulsion Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Leveraging a rapidly evolving state-of-the-art technical base empowered by Phase I NASA SBIR funding, NanoSonic's polymer derived rare earth silicate EBCs will...

  17. Radiation resistance of copper alloys at high exposure levels

    Energy Technology Data Exchange (ETDEWEB)

    Garner, F.A. (Pacific Northwest Lab., Richland, WA (USA)); Zinkle, S.J. (Oak Ridge National Lab., TN (USA))

    1990-08-01

    Copper alloys are currently being considered for high heat flux applications in fusion power devices. A review is presented of the results of two separate series of experiments on the radiation response of copper and copper alloys. One of these involved pure copper and boron-doped copper in the ORR mixed spectrum reactor. The other series included pure copper and a wide array of copper alloys irradiated in the FFTF fast reactor 16 refs., 13 figs.

  18. Abnormal Copper Homeostasis: Mechanisms and Roles in Neurodegeneration

    OpenAIRE

    Mario Manto

    2014-01-01

    As a cofactor of proteins and enzymes involved in critical molecular pathways in mammals and low eukaryotes, copper is a transition metal essential for life. The intra-cellular and extra-cellular metabolism of copper is under tight control, in order to maintain free copper concentrations at very low levels. Copper is a critical element for major neuronal functions, and the central nervous system is a major target of disorders of copper metabolism. Both the accumulation of copper and copper d...

  19. Smelting chlorination method applied to removal of copper from copper slags

    Institute of Scientific and Technical Information of China (English)

    李磊; 王华; 胡建杭

    2015-01-01

    In order to reasonably utilize the iron resources of copper slags, the smelting chlorination process was used to remove copper from copper slags. Higher holding temperature and O2 flow rate are beneficial to increasing copper removal rate. However, the Cu2O mode is formed by the reaction of surplus O2 and CuCl with O2 flow rate increasing over 0.4 L/min, causing CuCl volatilization rate and copper removal rate to decrease. The resulting copper removal rate of 84.34%is obtained under the optimum conditions of holding temperature of 1573 K, residence time of 10 min, CaCl2 addition amount of 0.1 (mass ratio of CaCl2 and the copper slag) and oxygen flow rate of 0.4 L/min. The efficient removal of copper from copper slags through chlorination is feasible.

  20. The formation of nuggets of highly siderophile elements in quenched silicate melts at high temperatures: Before or during the silicate quench?

    Science.gov (United States)

    Malavergne, V.; Charon, E.; Jones, J.; Cordier, P.; Righter, K.; Deldicque, D.; Hennet, L.

    2016-01-01

    The Highly Siderophile Elements (HSE) are powerful tracers of planetary differentiation. Despite the importance of their partitioning between silicate and metal for the understanding of planetary core formation, especially for the Earth and Mars, there is still a huge discrepancy between conclusions based on different high temperature (HT) experimental studies. These disagreements may be due to the presence of HSE micro and nanonuggets in HT experiments. The formation of these nuggets is still interpreted in different ways. One hypothesis is that these HSE nuggets formed during the quench of the silicate melt, while another hypothesis supposes that these nuggets formed before the quench and represented artefacts of HT experiments. The goal of this work is to clarify whether the presence of HSE nuggets in silicate melts is linked to a quench effect or not. Understanding the formation of these HSE nuggets represents thus a necessary step towards the resolution of the Earth's core formation scenarios. We performed new HT experiments (1275-2000 °C) at different oxygen fugacities (fO2), between ambient air up to ∼5 log units below the Iron-Wüstite buffer [IW-5], for two different silicate compositions (synthetic martian and terrestrial basalts) mixed with a metallic mixture of Pt-Au-Pd-Ru. Our 1275-1600 °C experiments were contained in either olivine, diopside or graphite crucible; experiments at 2000 °C were performed using a levitation method, so no capsule was necessary. Our samples contained quenched silicate melts, minerals (olivine, pyroxene, spinel depending on the run), a two-phase metallic bead and nano and micro-nuggets of HSE. Our samples underwent fine textural, structural and analytical characterizations. The distribution of the nuggets was not homogeneous throughout the quenched silicate melt. HSE nuggets were present within crystals. Dendritic textures from the quenched silicate melt formed around HSE nuggets, which could be crystallized, showing