WorldWideScience

Sample records for cooling granular gas

  1. Free cooling of the one-dimensional wet granular gas.

    Science.gov (United States)

    Zaburdaev, V Yu; Brinkmann, M; Herminghaus, S

    2006-07-07

    The free cooling behavior of a wet granular gas is studied in one dimension. We employ a particularly simple model system in which the interaction of wet grains is characterized by a fixed energy loss assigned to each collision. Macroscopic laws of energy dissipation and cluster formation are studied on the basis of numerical simulations and mean-field analytical calculations. We find a number of remarkable scaling properties which may shed light on earlier unexplained results for related systems.

  2. A He-gas Cooled, Stationary Granular Target

    CERN Document Server

    Pugnat, P

    2003-01-01

    In the CERN approach to the design of a neutrino factory, the repetition frequency of the proton beam is high enough to consider stationary solid targets as a viable solution for multi-MW beams. The target consists of high density tantalum spheres of 2 mm diameter which can efficiently be cooled by passing a high mass flow He-gas stream through the voids between the Ta-granules. Very small thermal shocks and stresses will arise in this fine grained structure due to the relatively long burst of 3.3 ms from the SPL-proton linac. In a quadruple target system where each target receives only one quarter of the total beam power of 4 MW, conservative temperature levels and adequate lifetimes of the target are estimated in its very high radiation environment. A conceptual design of the integration of the target into the magnetic horn-pion-collector is presented.

  3. Navier-Stokes hydrodynamics of thermal collapse in a freely cooling granular gas.

    Science.gov (United States)

    Kolvin, Itamar; Livne, Eli; Meerson, Baruch

    2010-08-01

    We show that, in dimension higher than one, heat diffusion and viscosity cannot arrest thermal collapse in a freely evolving dilute granular gas, even in the absence of gravity. Thermal collapse involves a finite-time blowup of the gas density. It was predicted earlier in ideal, Euler hydrodynamics of dilute granular gases in the absence of gravity, and in nonideal, Navier-Stokes granular hydrodynamics in the presence of gravity. We determine, analytically and numerically, the dynamic scaling laws that characterize the gas flow close to collapse. We also investigate bifurcations of a freely evolving dilute granular gas in circular and wedge-shaped containers. Our results imply that, in general, thermal collapse can only be arrested when the gas density becomes comparable with the close-packing density of grains. This provides a natural explanation to the formation of densely packed clusters of particles in a variety of initially dilute granular flows.

  4. Granular gas dynamics

    CERN Document Server

    Brilliantov, Nikolai

    2003-01-01

    While there is not yet any general theory for granular materials, significant progress has been achieved for dilute systems, also called granular gases. The contributions in this book address both the kinetic approach one using the Boltzmann equation for dissipative gases as well as the less established hydrodynamic description. The last part of the book is devoted to driven granular gases and their analogy with molecular fluids. Care has been taken so as to present the material in a pedagogical and self-contained way and this volume will thus be particularly useful to nonspecialists and newcomers to the field.

  5. Low Mach number theory of freely cooling granular gases

    CERN Document Server

    Meerson, Baruch; Vilenkin, Arkady

    2007-01-01

    We use hydrodynamic equations to investigate the dynamics of a freely cooling dilute granular gas with nearly elastic particle collisions. We assume a narrow channel geometry and focus on the regime where the sound travel time through the system is much shorter than the typical cooling time of the gas. As a result, the pressure rapidly becomes almost homogeneous, while the Mach number is small. Eliminating the sound waves and employing Lagrangian coordinates, we reduce the full hydrodynamics to a single nonlinear/nonlocal equation of a reaction-diffusion type. This equation describes a broad class of flows and, in particular, can follow the development of strongly nonlinear states during clustering instability. Without heat diffusion, the reduced equation is exactly soluble and develops a finite-time density blowup with the same local features as those exhibited by the recently found family of exact solutions of the full set of ideal hydrodynamic equations (Fouxon et al. 2007). The heat diffusion, however, ar...

  6. Energy decay in a granular gas collapse

    Science.gov (United States)

    Almazán, Lidia; Serero, Dan; Salueña, Clara; Pöschel, Thorsten

    2017-01-01

    An inelastic hard ball bouncing repeatedly off the ground comes to rest in finite time by performing an infinite number of collisions. Similarly, a granular gas under the influence of external gravity, condenses at the bottom of the confinement due to inelastic collisions. By means of hydrodynamical simulations, we find that the condensation process of a granular gas reveals a similar dynamics as the bouncing ball. Our result is in agreement with both experiments and particle simulations, but disagrees with earlier simplified hydrodynamical description. Analyzing the result in detail, we find that the adequate modeling of pressure plays a key role in continuum modeling of granular matter.

  7. Gas cooled fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1972-06-01

    Although most of the development work on fast breeder reactors has been devoted to the use of liquid metal cooling, interest has been expressed for a number of years in alternative breeder concepts using other coolants. One of a number of concepts in which interest has been retained is the Gas-Cooled Fast Reactor (GCFR). As presently envisioned, it would operate on the uranium-plutonium mixed oxide fuel cycle, similar to that used in the Liquid Metal Fast Breeder Reactor (LMFBR), and would use helium gas as the coolant.

  8. Freely cooling granular gases with short-ranged attractive potentials

    Energy Technology Data Exchange (ETDEWEB)

    Murphy, Eric; Subramaniam, Shankar, E-mail: shankar@iastate.edu [Department of Mechanical Engineering, Center for Multiphase Flow Research, Iowa State University, Ames, Iowa 50011 (United States)

    2015-04-15

    We treat the case of an undriven gas of inelastic hard-spheres with short-ranged attractive potentials via an extension of the pseudo-Liouville operator formalism. New evolution equations for the granular temperature and coordination number are obtained. The granular temperature exhibits deviation from both Haff’s law and the case of long-ranged potentials. We verify this departure using soft-sphere discrete element method simulations. Excellent agreement is found for the duration of the simulation even beyond where exclusively binary collisions are expected. Simulations show the emergence of strong spatial-velocity correlations on the length scale of the last peak in the pair-correlation function but do not show strong correlations beyond this length scale. We argue that molecular chaos may remain an adequate approximation if the system is modelled as a Smoluchowski type equation with aggregation and break-up processes.

  9. Freely cooling granular gases with short-ranged attractive potentials

    Science.gov (United States)

    Murphy, Eric; Subramaniam, Shankar

    2015-04-01

    We treat the case of an undriven gas of inelastic hard-spheres with short-ranged attractive potentials via an extension of the pseudo-Liouville operator formalism. New evolution equations for the granular temperature and coordination number are obtained. The granular temperature exhibits deviation from both Haff's law and the case of long-ranged potentials. We verify this departure using soft-sphere discrete element method simulations. Excellent agreement is found for the duration of the simulation even beyond where exclusively binary collisions are expected. Simulations show the emergence of strong spatial-velocity correlations on the length scale of the last peak in the pair-correlation function but do not show strong correlations beyond this length scale. We argue that molecular chaos may remain an adequate approximation if the system is modelled as a Smoluchowski type equation with aggregation and break-up processes.

  10. Gas cooled traction drive inverter

    Science.gov (United States)

    Chinthavali, Madhu Sudhan

    2013-10-08

    The present invention provides a modular circuit card configuration for distributing heat among a plurality of circuit cards. Each circuit card includes a housing adapted to dissipate heat in response to gas flow over the housing. In one aspect, a gas-cooled inverter includes a plurality of inverter circuit cards, and a plurality of circuit card housings, each of which encloses one of the plurality of inverter cards.

  11. Gas cooled traction drive inverter

    Energy Technology Data Exchange (ETDEWEB)

    Chinthavali, Madhu Sudhan

    2016-04-19

    The present invention provides a modular circuit card configuration for distributing heat among a plurality of circuit cards. Each circuit card includes a housing adapted to dissipate heat in response to gas flow over the housing. In one aspect, a gas-cooled inverter includes a plurality of inverter circuit cards, and a plurality of circuit card housings, each of which encloses one of the plurality of inverter cards.

  12. Granular gas in a periodic lattice

    Science.gov (United States)

    Dorbolo, S.; Brandenbourger, M.; Damanet, F.; Dister, H.; Ludewig, F.; Terwagne, D.; Lumay, G.; Vandewalle, N.

    2011-11-01

    Glass beads are placed in the compartments of a horizontal square grid. This grid is then vertically shaken. According to the reduced acceleration Γ of the system, the granular material exhibits various behaviours. By counting the number of beads in each compartment after shaking, it is possible to define three regimes. At low accelerations, the grains remain in their compartment, and the system is frozen. For very large accelerations, the grains bounce out of the compartments and behave as a 'binomial gas': the system is homogeneous. For intermediate accelerations, grains form clusters, i.e. grains gather in some particular compartments. In that regime, the probability for a bead to escape from a site depends on the number of beads contained in the concerned compartment. The escape probability has been measured with respect to the number of beads in a compartment. Above a given number of beads, the beads remain trapped in the compartment. A basic numerical model reproduces some of the results and allows us to explore the dependence on the initial conditions.

  13. Granular bed filtration of high temperature biomass gasification gas.

    Science.gov (United States)

    Stanghelle, Daniel; Slungaard, Torbjørn; Sønju, Otto K

    2007-06-18

    High temperature cleaning of producer gas from biomass gasification has been investigated with a granular filter. Field tests were performed for several hours on a single filter element at about 550 degrees C. The results show cake filtration on the granular material and indicate good filtration of the biomass gasification producer gas. The relatively low pressure drop over the filter during filtration is comparable to those of bag filters. The granular filter can operate with high filtration velocities compared to bag filters and maintain high efficiency and a low residual pressure. This work is a part of the BioSOFC-up project that has a goal of utilizing the producer gas from the gasification plant in a solid oxide fuel cell (SOFC). The BioSOFC-up project will continue to the end of 2007.

  14. Impingement jet cooling in gas turbines

    CERN Document Server

    Amano, R S

    2014-01-01

    Due to the requirement for enhanced cooling technologies on modern gas turbine engines, advanced research and development has had to take place in field of thermal engineering. Impingement jet cooling is one of the most effective in terms of cooling, manufacturability and cost. This is the first to book to focus on impingement cooling alone.

  15. Argon purge gas cooled by chill box

    Science.gov (United States)

    Spiro, L. W.

    1966-01-01

    Cooling argon purge gas by routing it through a shop-fabricated chill box reduces charring of tungsten inert gas torch head components. The argon gas is in a cooled state as it enters the torch and prevents buildup of char caused by the high concentrations of heat in the weld area during welding operations.

  16. Nonlinear theory of nonstationary low Mach number channel flows of freely cooling nearly elastic granular gases.

    Science.gov (United States)

    Meerson, Baruch; Fouxon, Itzhak; Vilenkin, Arkady

    2008-02-01

    We employ hydrodynamic equations to investigate nonstationary channel flows of freely cooling dilute gases of hard and smooth spheres with nearly elastic particle collisions. This work focuses on the regime where the sound travel time through the channel is much shorter than the characteristic cooling time of the gas. As a result, the gas pressure rapidly becomes almost homogeneous, while the typical Mach number of the flow drops well below unity. Eliminating the acoustic modes and employing Lagrangian coordinates, we reduce the hydrodynamic equations to a single nonlinear and nonlocal equation of a reaction-diffusion type. This equation describes a broad class of channel flows and, in particular, can follow the development of the clustering instability from a weakly perturbed homogeneous cooling state to strongly nonlinear states. If the heat diffusion is neglected, the reduced equation becomes exactly soluble, and the solution develops a finite-time density blowup. The blowup has the same local features at singularity as those exhibited by the recently found family of exact solutions of the full set of ideal hydrodynamic equations [I. Fouxon, Phys. Rev. E 75, 050301(R) (2007); I. Fouxon,Phys. Fluids 19, 093303 (2007)]. The heat diffusion, however, always becomes important near the attempted singularity. It arrests the density blowup and brings about previously unknown inhomogeneous cooling states (ICSs) of the gas, where the pressure continues to decay with time, while the density profile becomes time-independent. The ICSs represent exact solutions of the full set of granular hydrodynamic equations. Both the density profile of an ICS and the characteristic relaxation time toward it are determined by a single dimensionless parameter L that describes the relative role of the inelastic energy loss and heat diffusion. At L>1 the intermediate cooling dynamics proceeds as a competition between "holes": low-density regions of the gas. This competition resembles Ostwald

  17. Injected power and entropy flow in a heated granular gas

    Science.gov (United States)

    Visco, P.; Puglisi, A.; Barrat, A.; Trizac, E.; van Wijland, F.

    2005-10-01

    Our interest goes to the power injected in a heated granular gas and to the possibility to interpret it in terms of entropy flow. We numerically determine the distribution of the injected power by means of Monte Carlo simulations. Then, we provide a kinetic-theory approach to the computation of such a distribution function. Finally, after showing why the injected power does not satisfy a fluctuation relation à la Gallavotti-Cohen, we put forward a new quantity which does fulfill such a relation, and is not only applicable in a variety of frameworks outside the granular world, but also experimentally accessible.

  18. Gas flow within Martian soil: experiments on granular Knudsen compressors

    Science.gov (United States)

    Koester, Marc; Kelling, Thorben; Teiser, Jens; Wurm, Gerhard

    2017-09-01

    Thermal creep efficiently transports gas through Martian soil. To quantify the Martian soil pump we carried out laboratory analog experiments with illuminated granular media at low ambient pressure. We used samples of 1 μm to 5 μm SiO2 (quartz), basalt with a broad size distribution between 63 μm and 125 μm, and JSC-Mars 1A with a size fraction from 125 μm to 250 μm. The mean ambient pressure was varied between 50 Pa and 9000 Pa. Illumination was varied between 100 W/m2 and 6700 W/m2. The experiments confirm strong directed gas flows within granular and dusty soil and local sub-soil pressure variations. We find that Martian soil pumps can be described with existing models of thermal creep for capillaries, using the average grain size and light flux related temperatures.

  19. Cooling arrangement for a gas turbine component

    Science.gov (United States)

    Lee, Ching-Pang; Heneveld, Benjamin E

    2015-02-10

    A cooling arrangement (82) for a gas turbine engine component, the cooling arrangement (82) having a plurality of rows (92, 94, 96) of airfoils (98), wherein adjacent airfoils (98) within a row (92, 94, 96) define segments (110, 130, 140) of cooling channels (90), and wherein outlets (114, 134) of the segments (110, 130) in one row (92, 94) align aerodynamically with inlets (132, 142) of segments (130, 140) in an adjacent row (94, 96) to define continuous cooling channels (90) with non continuous walls (116, 120), each cooling channel (90) comprising a serpentine shape.

  20. Plane shock wave structure in a dilute granular gas

    Science.gov (United States)

    Reddy, M. H. Lakshminarayana; Alam, Meheboob

    2016-11-01

    We analyse the early time evolution of the Riemann problem of planar shock wave structures for a dilute granular gas by solving Navier-Stokes equations numerically. The one-dimensional reduced Navier-Stokes equations for plane shock wave problem are solved numerically using a relaxation-type numerical scheme. The results on the shock structures in granular gases are presented for different Mach numbers and restitution coefficients. Based on our analysis on early time shock dynamics we conclude that the density and temperature profiles are "asymmetric"; the density maximum and the temperature maximum occur within the shock layer; the absolute magnitudes of longitudinal stress and heat flux which are initially zero at both end states attain maxima in a very short time and thereafter decrease with time.

  1. Warm Absorbing Gas in Cooling Flows

    OpenAIRE

    Buote, David A.

    2000-01-01

    We summarize the discovery of oxygen absorption and warm (10^5-10^6 K) gas in cooling flows. Special attention is given to new results for M87 for which we find the strongest evidence to date for ionized oxygen absorption in these systems. We briefly discuss implications for observations of cooling flows with Chandra and XMM.

  2. Symmetry-breaking instability in a prototypical driven granular gas.

    Science.gov (United States)

    Khain, Evgeniy; Meerson, Baruch

    2002-08-01

    Symmetry-breaking instability of a laterally uniform granular cluster (strip state) in a prototypical driven granular gas is investigated. The system consists of smooth hard disks in a two-dimensional box, colliding inelastically with each other and driven, at zero gravity, by a "thermal" wall. The limit of nearly elastic particle collisions is considered, and granular hydrodynamics with the Jenkins-Richman constitutive relations is employed. The hydrodynamic problem is completely described by two scaled parameters and the aspect ratio of the box. Marginal stability analysis predicts a spontaneous symmetry-breaking instability of the strip state, similar to that predicted recently for a different set of constitutive relations. If the system is big enough, the marginal stability curve becomes independent of the details of the boundary condition at the driving wall. In this regime, the density perturbation is exponentially localized at the elastic wall opposite the thermal wall. The short- and long-wavelength asymptotics of the marginal stability curves are obtained analytically in the dilute limit. The physics of the symmetry-breaking instability is discussed.

  3. Hot gas path component cooling system

    Science.gov (United States)

    Lacy, Benjamin Paul; Bunker, Ronald Scott; Itzel, Gary Michael

    2014-02-18

    A cooling system for a hot gas path component is disclosed. The cooling system may include a component layer and a cover layer. The component layer may include a first inner surface and a second outer surface. The second outer surface may define a plurality of channels. The component layer may further define a plurality of passages extending generally between the first inner surface and the second outer surface. Each of the plurality of channels may be fluidly connected to at least one of the plurality of passages. The cover layer may be situated adjacent the second outer surface of the component layer. The plurality of passages may be configured to flow a cooling medium to the plurality of channels and provide impingement cooling to the cover layer. The plurality of channels may be configured to flow cooling medium therethrough, cooling the cover layer.

  4. Imperfect pitchfork bifurcation in asymmetric two-compartment granular gas

    Institute of Scientific and Technical Information of China (English)

    Zhang Yin; Li Yin-Chang; Liu Rui; Cui Fei-Fei; Pierre Evesque; Hou Mei-Ying

    2013-01-01

    The clustering behavior of a mono-disperse granular gas is experimentally studied in an asymmetric two-compartment setup.Unlike the random clustering in either compartment in the case of symmetric configuration when lowering the shaking strength to below a critical value,the directed clustering is observed,which corresponds to an imperfect pitchfork bifurcation.Numerical solutions of the flux equation using a modified simple flux function show qualitative agreements with the experimental results.The potential application of this asymmetric structure is discussed.

  5. Ship exhaust gas plume cooling

    NARCIS (Netherlands)

    Schleijpen, H.M.A.; Neele, P.P.

    2004-01-01

    The exhaust gas plume is an important and sometimes dominating contributor to the infrared signature of ships. Suppression of the infrared ship signatures has been studied by TNO for the Royal Netherlands Navy over considerable time. This study deals with the suppression effects, which can be achiev

  6. Incorporation of Interstitial Gas Effects on Granular Flows

    Science.gov (United States)

    Hrenya, Christine; Garzo, Vicente; Tenneti, Sudheer; Subramaniam, Shankar

    2013-11-01

    Numerous examples of granular flows exist in which the role of the interstitial gas cannot be ignored. A range of approaches have been taken to incorporate these effects into continuum descriptions. Early efforts simply added a mean drag law to the momentum balance. This ad hoc approach was followed by more rigorous treatments in which an instantaneous drag was incorporated directly into the kinetic equation. Analytical expressions for the resulting continuum description were obtained in the Stokes limit, but not possible higher Reynolds numbers. In the current effort, DNS-based simulations are used to develop a model for the instantaneous drag force that is applicable to a wide range of Reynolds number. This model, based on the Langevin equation, is incorporated into the Enskog equation in order to derive a continuum description for the gas-solid flow. In the limit of Stokes flow, the additional terms arising in the conservation equation are found to match those of previous analytical treatments. Furthermore, the impact of gas on the solid-phase constitutive relations, which was ignored in analytical treatments, is determined. The parameter space examined is consistent with that found in circulating fluidized beds. For such systems, the results indicate a non-negligible impact of the gas phase on the shear viscosity and the Dufour coefficient.

  7. System of elastic hard spheres which mimics the transport properties of a granular gas.

    Science.gov (United States)

    Santos, Andrés; Astillero, Antonio

    2005-09-01

    The prototype model of a fluidized granular system is a gas of inelastic hard spheres (IHS) with a constant coefficient of normal restitution alpha. Using a kinetic theory description we investigate the two basic ingredients that a model of elastic hard spheres (EHS) must have in order to mimic the most relevant transport properties of the underlying IHS gas. First, the EHS gas is assumed to be subject to the action of an effective drag force with a friction constant equal to half the cooling rate of the IHS gas, the latter being evaluated in the local equilibrium approximation for simplicity. Second, the collision rate of the EHS gas is reduced by a factor (1/2)(1+alpha), relative to that of the IHS gas. Comparison between the respective Navier-Stokes transport coefficients shows that the EHS model reproduces almost perfectly the self-diffusion coefficient and reasonably well the two transport coefficients defining the heat flux, the shear viscosity being reproduced within a deviation less than 14% (for alpha > or = 0.5). Moreover, the EHS model is seen to agree with the fundamental collision integrals of inelastic mixtures and dense gases. The approximate equivalence between IHS and EHS is used to propose kinetic models for inelastic collisions as simple extensions of known kinetic models for elastic collisions.

  8. Cooling of Gas Turbines. 2; Effectiveness of Rim Cooling of Blades

    Science.gov (United States)

    Wolfenstein, Lincoln; Meyer, Gene L.; McCarthy, John S.

    1945-01-01

    An analysis of rim cooling, which cools the blade by condition alone, was conducted. Gas temperatures ranged from 1300 degrees to 1900 degrees F and rim temperatures from 0 degrees to 1000 degrees F below gas temperatures. Results show that gas temperature increases up to 200 degrees F are permissible provided that the blades are cooled by 400 degrees to 500 degrees F below the gas temperature. Relatively small amounts of blade cooling, at constant gas temperature, give large increases in blade life. Dependence of rim cooling on heat-transfer coefficient, blade dimensions, and thermal conductivity is determined by a single parameter.

  9. Cooling circuit for a gas turbine bucket and tip shroud

    Energy Technology Data Exchange (ETDEWEB)

    Willett, Fred Thomas (25 Long Creek Dr., Burnt Hills, NY 12027); Itzel, Gary Michael (12 Cider Mill Dr., Clifton Park, NY 12065); Stathopoulos, Dimitrios (11 Wyngate Rd., Glenmont, NY 12077); Plemmons, Larry Wayne (late of Hamilton, OH); Plemmons, Helen M. (2900 Long Ridge Trails, Hamilton, OH 45014); Lewis, Doyle C. (444 River Way, Greer, SC 29651)

    2002-01-01

    An open cooling circuit for a gas turbine bucket wherein the bucket has an airfoil portion, and a tip shroud, the cooling circuit including a plurality of radial cooling holes extending through the airfoil portion and communicating with an enlarged internal area within the tip shroud before exiting the tip shroud such that a cooling medium used to cool the airfoil portion is subsequently used to cool the tip shroud.

  10. Clustering and velocity distributions in granular gases cooling by solid friction.

    Science.gov (United States)

    Das, Prasenjit; Puri, Sanjay; Schwartz, Moshe

    2016-09-01

    We present large-scale molecular dynamics simulations to study the free evolution of granular gases. Initially, the density of particles is homogeneous and the velocity follows a Maxwell-Boltzmann (MB) distribution. The system cools down due to solid friction between the granular particles. The density remains homogeneous, and the velocity distribution remains MB at early times, while the kinetic energy of the system decays with time. However, fluctuations in the density and velocity fields grow, and the system evolves via formation of clusters in the density field and the local ordering of velocity field, consistent with the onset of plug flow. This is accompanied by a transition of the velocity distribution function from MB to non-MB behavior. We used equal-time correlation functions and structure factors of the density and velocity fields to study the morphology of clustering. From the correlation functions, we obtain the cluster size, L, as a function of time, t. We show that it exhibits power law growth with L(t)∼t^{1/3}.

  11. Clustering and velocity distributions in granular gases cooling by solid friction

    Science.gov (United States)

    Das, Prasenjit; Puri, Sanjay; Schwartz, Moshe

    2016-09-01

    We present large-scale molecular dynamics simulations to study the free evolution of granular gases. Initially, the density of particles is homogeneous and the velocity follows a Maxwell-Boltzmann (MB) distribution. The system cools down due to solid friction between the granular particles. The density remains homogeneous, and the velocity distribution remains MB at early times, while the kinetic energy of the system decays with time. However, fluctuations in the density and velocity fields grow, and the system evolves via formation of clusters in the density field and the local ordering of velocity field, consistent with the onset of plug flow. This is accompanied by a transition of the velocity distribution function from MB to non-MB behavior. We used equal-time correlation functions and structure factors of the density and velocity fields to study the morphology of clustering. From the correlation functions, we obtain the cluster size, L , as a function of time, t . We show that it exhibits power law growth with L (t ) ˜t1 /3 .

  12. Modeling gas formation and mineral precipitation in a granular iron column.

    Science.gov (United States)

    Jeen, Sung-Wook; Amos, Richard T; Blowes, David W

    2012-06-19

    In granular iron permeable reactive barriers (PRBs), hydrogen gas formation, entrapment and release of gas bubbles, and secondary mineral precipitation have been known to affect the permeability and reactivity. The multicomponent reactive transport model MIN3P was enhanced to couple gas formation and release, secondary mineral precipitation, and the effects of these processes on hydraulic properties and iron reactivity. The enhanced model was applied to a granular iron column, which was studied for the treatment of trichloroethene (TCE) in the presence of dissolved CaCO(3). The simulation reasonably reproduced trends in gas formation, secondary mineral precipitation, permeability changes, and reactivity changes observed over time. The simulation showed that the accumulation of secondary minerals reduced the reactivity of the granular iron over time, which in turn decreased the rate of mineral accumulation, and also resulted in a gradual decrease in gas formation over time. This study provides a quantitative assessment of the evolving nature of geochemistry and permeability, resulting from coupled processes of gas formation and mineral precipitation, which leads to a better understanding of the processes controlling the granular iron reactivity, and represents an improved method for incorporating these factors into the design of granular iron PRBs.

  13. Granular Media under Vibration in Zero Gravity: Transition from Rattling to Granular Gas

    CERN Document Server

    Evesque, P; Zhai, G; Hou, M

    2011-01-01

    We report on different experimental behaviours of granular dissipative matter excited by vibration as studied during the 43rd ESA campaign of Airbus A300-0g from CNES. The effect of g-jitter is quantified through the generation of a rattle effect. The French-European team's electromagnetic set-up is used, with 20Hz cam recording and high speed camera for a short duration (1s) during each parabola.

  14. Gas-driven subharmonic waves in a vibrated two-phase granular material.

    Science.gov (United States)

    Matas, J-P; Uehara, J; Behringer, R P

    2008-04-01

    Vibrated powders exhibit striking phenomena: subharmonic waves, oscillons, convection, heaping, and even bubbling. We demonstrate novel rectangular profile subharmonic waves for vibrated granular material, that occur uniquely in the two-phase case of grains, and a fluid, such as air. These waves differ substantially from those for the gas-free case, exhibit different dispersion relations, and occur for specific shaking parameters and air pressure, understandable with gas-particle flow models. These waves occur when the gas diffusively penetrates the granular layer in a time comparable to the shaker period. As the pressure is lowered towards P =0, the granular-gas system exhibits a Knudsen regime. This instability provides an opportunity to quantitatively test models of two-phase flow.

  15. Gas turbine vane cooling air insert

    Energy Technology Data Exchange (ETDEWEB)

    North, W.E.; Hultgren, K.G.; Dishman, C.D.; Van Heusden, G.S.

    1992-09-08

    This patent describes a gas turbine. It comprises turbine vanes, each of the vanes supplied with cooling air and having: an airfoil portion forming a first cavity having an insert disposed therein for directing the flow of the cooling air, the insert having first and second insert ends; a shroud portion from which the airfoil portion extends, the insert attached to the shroud portion at the first insert end; an insert extension extending through a portion of the insert and extending beyond the first insert end, the insert extension and the insert forming an annular gap therebetween separating the insert from the insert extension; a plate covering at least a portion of the shroud, the plate having a first hole formed therein through which the insert extension extends; and at least a first seal extending between the insert extension and the insert, and sealing the annular gap therebetween. This patent also describes a method of making a gas turbine. It comprises welding a first tubular insert adjacent its first end to a vane outer shroud; partially inserting a second tubular insert into the first tubular member and attaching the second tubular insert thereto; placing a plate having a hole formed therein on the outer shroud so that the hole surrounds the second tubular insert; and attaching the second tubular insert to the plate by placing a first seal between the first and second tubular inserts and attaching the first seal to each of the first and second tubular inserts, and placing a second seal between the second tubular insert and the plate and welding the second seal to the second tubular insert and the plate.

  16. Inelastic gas: An experimental study of vibro-fluidized dilute granular media

    Science.gov (United States)

    Feitosa, Klebert Bezerra

    We conduct an experimental study of a two dimensional vibro-fluidized dilute granular medium. The system is composed of spherical beads confined to move in a vertical plane and excited by intense vertical vibrations. We perform full-field tracking of positions and orientations of the spheres by high speed photography. In steady-state, the motion of the grains resembles that of a molecular gas, thus the name granular gas. We study the distribution of linear velocities in the granular gas. The investigation shows that the distributions are non-gaussian, best fitted by the function P(v) ˜ exp(-beta| v|/sigma)1.5), and insensitive to number density, driving parameters and particle inelasticity. The distribution is a one parameter distribution, parameterized by the mean square velocity; which defines a granular temperature. T = ½ . We study binary mixtures of the granular media. We find that, in general, the granular temperature is not equal for the two types of spheres. However, the temperature ratio is constant in the bulk. The ratio depends strongly on the mass ratio of the spheres, but not on their inelasticity. The ratio is also insensitive to compositional parameters of the mixture such as number fraction and number density. We also investigate the statistics of the power flux into a subsystem of the granular gas. The power shows large fluctuations, including frequent large negative fluctuations. The relative probabilities of positive and negative fluctuations in the power flux are in close accord with the Fluctuation Theorem of Gallavotti and Cohen (Gallavotti & Cohen, 1995b). We also compare the effective temperature that emerges from this analysis to the kinetic granular temperature. Finally, we study the rotational dynamics of the granular gas. We find that the granular temperature is not equipartitioned between translational and rotational degrees of freedom. We also demonstrate that the ratio of rotational to translational energy is independent of the

  17. Application of Hastelloy X in Gas-Cooled Reactor Systems

    DEFF Research Database (Denmark)

    Brinkman, C. R.; Rittenhouse, P. L.; Corwin, W.R.

    1976-01-01

    Hastelloy X, an Ni--Cr--Fe--Mo alloy, may be an important structural alloy for components of gas-cooled reactor systems. Expected applications of this alloy in the High-Temperature Gas-Cooled Reactor (HTGR) are discussed, and the development of interim mechanical properties and supporting data...

  18. Gas turbine heat transfer and cooling technology

    CERN Document Server

    Han, Je-Chin; Ekkad, Srinath

    2012-01-01

    FundamentalsNeed for Turbine Blade CoolingTurbine-Cooling TechnologyTurbine Heat Transfer and Cooling IssuesStructure of the BookReview Articles and Book Chapters on Turbine Cooling and Heat TransferNew Information from 2000 to 2010ReferencesTurbine Heat TransferIntroductionTurbine-Stage Heat TransferCascade Vane Heat-Transfer ExperimentsCascade Blade Heat TransferAirfoil Endwall Heat TransferTurbine Rotor Blade Tip Heat TransferLeading-Edge Region Heat TransferFlat-Surface Heat TransferNew Information from 2000 to 20102.10 ClosureReferencesTurbine Film CoolingIntroductionFilm Cooling on Rotat

  19. Evaluating the income and employment impacts of gas cooling technologies

    Energy Technology Data Exchange (ETDEWEB)

    Hughes, P.J. [Oak Ridge National Lab., TN (United States); Laitner, S.

    1995-03-01

    The purpose of this study is to estimate the potential employment and income benefits of the emerging market for gas cooling products. The emphasis here is on exports because that is the major opportunity for the U.S. heating, ventilating, and air-conditioning (HVAC) industry. But domestic markets are also important and considered here because without a significant domestic market, it is unlikely that the plant investments, jobs, and income associated with gas cooling exports would be retained within the United States. The prospects for significant gas cooling exports appear promising for a variety of reasons. There is an expanding need for cooling in the developing world, natural gas is widely available, electric infrastructures are over-stressed in many areas, and the cost of building new gas infrastructure is modest compared to the cost of new electric infrastructure. Global gas cooling competition is currently limited, with Japanese and U.S. companies, and their foreign business partners, the only product sources. U.S. manufacturers of HVAC products are well positioned to compete globally, and are already one of the faster growing goods-exporting sectors of the U.S. economy. Net HVAC exports grew by over 800 percent from 1987 to 1992 and currently exceed $2.6 billion annually (ARI 1994). Net gas cooling job and income creation are estimated using an economic input-output model to compare a reference case to a gas cooling scenario. The reference case reflects current policies, practices, and trends with respect to conventional electric cooling technologies. The gas cooling scenario examines the impact of accelerated use of natural gas cooling technologies here and abroad.

  20. Evaluating the income and employment impacts of gas cooling technologies

    Energy Technology Data Exchange (ETDEWEB)

    Hughes, P.J. [Oak Ridge National Lab., TN (United States); Laitner, S.

    1995-03-01

    The purpose of this study is to estimate the potential employment and income benefits of the emerging market for gas cooling products. The emphasis here is on exports because that is the major opportunity for the U.S. heating, ventilating, and air-conditioning (HVAC) industry. But domestic markets are also important and considered here because without a significant domestic market, it is unlikely that the plant investments, jobs, and income associated with gas cooling exports would be retained within the United States. The prospects for significant gas cooling exports appear promising for a variety of reasons. There is an expanding need for cooling in the developing world, natural gas is widely available, electric infrastructures are over-stressed in many areas, and the cost of building new gas infrastructure is modest compared to the cost of new electric infrastructure. Global gas cooling competition is currently limited, with Japanese and U.S. companies, and their foreign business partners, the only product sources. U.S. manufacturers of HVAC products are well positioned to compete globally, and are already one of the faster growing goods-exporting sectors of the U.S. economy. Net HVAC exports grew by over 800 percent from 1987 to 1992 and currently exceed $2.6 billion annually (ARI 1994). Net gas cooling job and income creation are estimated using an economic input-output model to compare a reference case to a gas cooling scenario. The reference case reflects current policies, practices, and trends with respect to conventional electric cooling technologies. The gas cooling scenario examines the impact of accelerated use of natural gas cooling technologies here and abroad.

  1. Thermal properties of an impurity immersed in a granular gas of rough hard spheres

    Directory of Open Access Journals (Sweden)

    Vega Reyes Francisco

    2017-01-01

    Full Text Available We study in this work the dynamics of a granular impurity immersed in a low-density granular gas of identical particles. For description of the kinetics of the granular gas and the impurity particles we use the rough hard sphere collisional model. We take into account the effects of non-conservation of energy upon particle collision. We find an (approximate analytical solution of the pertinent kinetic equations for the single-particle velocity distribution functions that reproduces reasonably well the properties of translational/rotational energy non-equipartition. We assess the accuracy of the theoretical solution by comparing with computer simulations. For this, we use two independent computer data sets, from molecular dynamics (MD and from Direct Simulation Monte Carlo method (DSMC. Both approach well, with different degrees, the kinetic theory within a reasonable range of parameter values.

  2. Thermal properties of an impurity immersed in a granular gas of rough hard spheres

    Science.gov (United States)

    Vega Reyes, Francisco; Lasanta, Antonio; Santos, Andrés; Garzó, Vicente

    2017-06-01

    We study in this work the dynamics of a granular impurity immersed in a low-density granular gas of identical particles. For description of the kinetics of the granular gas and the impurity particles we use the rough hard sphere collisional model. We take into account the effects of non-conservation of energy upon particle collision. We find an (approximate) analytical solution of the pertinent kinetic equations for the single-particle velocity distribution functions that reproduces reasonably well the properties of translational/rotational energy non-equipartition. We assess the accuracy of the theoretical solution by comparing with computer simulations. For this, we use two independent computer data sets, from molecular dynamics (MD) and from Direct Simulation Monte Carlo method (DSMC). Both approach well, with different degrees, the kinetic theory within a reasonable range of parameter values.

  3. Regularized Moment Equations and Shock Waves for Rarefied Granular Gas

    Science.gov (United States)

    Reddy, Lakshminarayana; Alam, Meheboob

    2016-11-01

    It is well-known that the shock structures predicted by extended hydrodynamic models are more accurate than the standard Navier-Stokes model in the rarefied regime, but they fail to predict continuous shock structures when the Mach number exceeds a critical value. Regularization or parabolization is one method to obtain smooth shock profiles at all Mach numbers. Following a Chapman-Enskog-like method, we have derived the "regularized" version 10-moment equations ("R10" moment equations) for inelastic hard-spheres. In order to show the advantage of R10 moment equations over standard 10-moment equations, the R10 moment equations have been employed to solve the Riemann problem of plane shock waves for both molecular and granular gases. The numerical results are compared between the 10-moment and R10-moment models and it is found that the 10-moment model fails to produce continuous shock structures beyond an upstream Mach number of 1 . 34 , while the R10-moment model predicts smooth shock profiles beyond the upstream Mach number of 1 . 34 . The density and granular temperature profiles are found to be asymmetric, with their maxima occurring within the shock-layer.

  4. Effective potentials in a bidimensional vibrated granular gas

    Science.gov (United States)

    Velázquez-Pérez, Stephanie; Pérez-Ángel, Gabriel; Nahmad-Molinari, Yuri

    2016-09-01

    We present a numerical study of the spatial correlations of a quasi-two-dimensional granular fluid kept in a nonstatic steady state via vertical shaking. The simulations explore a wide range of vertical accelerations, restitution coefficients, and packing fractions, always staying below the crystallization limit. From the simulations we obtain the relevant pair distribution functions (PDFs), and effective potentials for the interparticle interaction are extracted from these PDFs via the Ornstein-Zernike equation with the Percus-Yevick closure. The correlations in the granular structures originating from these effective potentials are checked against the originating PDF using standard Monte Carlo simulations, and we find in general an excellent agreement. The resulting effective potentials show an increase of the spatial correlation at contact with the decreasing values of the restitution coefficient, and a tendency of the potentials to display deeper wells for more dissipative dynamics. A general exception to this trend appears for a range of values of the forcing, which depends on the restitution coefficient, but not on the density, where resonant bouncing increases correlations, resulting in deeper potential wells. The nature of these resonances is explored and shown to be the result of synchronization in the parabolic flights of the particles.

  5. Radial molecular abundances and gas cooling in starless cores

    CERN Document Server

    Sipilä, O

    2012-01-01

    Aims: We aim to simulate radial profiles of molecular abundances and the gas temperature in cold and heavily shielded starless cores by combining chemical and radiative transfer models. Methods: A determination of the dust temperature in a modified Bonnor-Ebert sphere is used to calculate initial radial molecular abundance profiles. The abundances of selected cooling molecules corresponding to two different core ages are then extracted to determine the gas temperature at two time steps. The calculation is repeated in an iterative process yielding molecular abundances consistent with the gas temperature. Line emission profiles for selected substances are calculated using simulated abundance profiles. Results: The gas temperature is a function of time; the gas heats up as the core gets older because the cooling molecules are depleted onto grain surfaces. The contributions of the various cooling molecules to the total cooling power change with time. Radial chemical abundance profiles are non-trivial: different s...

  6. High temperature gas-cooled reactor: gas turbine application study

    Energy Technology Data Exchange (ETDEWEB)

    1980-12-01

    The high-temperature capability of the High-Temperature Gas-Cooled Reactor (HTGR) is a distinguishing characteristic which has long been recognized as significant both within the US and within foreign nuclear energy programs. This high-temperature capability of the HTGR concept leads to increased efficiency in conventional applications and, in addition, makes possible a number of unique applications in both electrical generation and industrial process heat. In particular, coupling the HTGR nuclear heat source to the Brayton (gas turbine) Cycle offers significant potential benefits to operating utilities. This HTGR-GT Application Study documents the effort to evaluate the appropriateness of the HTGR-GT as an HTGR Lead Project. The scope of this effort included evaluation of the HTGR-GT technology, evaluation of potential HTGR-GT markets, assessment of the economics of commercial HTGR-GT plants, and evaluation of the program and expenditures necessary to establish HTGR-GT technology through the completion of the Lead Project.

  7. Fluctuations of Internal Energy Flow in a Vibrated Granular Gas

    Science.gov (United States)

    Puglisi, Andrea; Visco, Paolo; Barrat, Alain; Trizac, Emmanuel; van Wijland, Frédéric

    2005-09-01

    The nonequilibrium fluctuations of power flux in a fluidized granular media have been recently measured in an experiment [Phys. Rev. Lett. 92, 164301 (2004)PRLTAO0031-900710.1103/PhysRevLett.92.164301], which was announced to be a verification of the fluctuation relation (FR) by Gallavotti and Cohen. An effective temperature was also identified and proposed to be a useful probe for such nonequilibrium systems. We explain these results in terms of a two-temperature Poisson process. Within this model, supported by independent molecular dynamics simulations, power flux fluctuations do not satisfy the FR and the nature of the effective temperature is clarified. In the pursuit of a hypothetical global quantity fulfilling the FR, this points to the need of considering candidates other than the power flux.

  8. PolyPole-1: An accurate numerical algorithm for intra-granular fission gas release

    Energy Technology Data Exchange (ETDEWEB)

    Pizzocri, D.; Rabiti, C.; Luzzi, L.; Barani, T.; Van Uffelen, P.; Pastore, G.

    2016-09-01

    This paper describes the development of a new numerical algorithm (called PolyPole-1) to efficiently solve the equation for intra-granular fission gas release in nuclear fuel. The work was carried out in collaboration with Politecnico di Milano and Institute for Transuranium Elements. The PolyPole-1 algorithms is being implemented in INL's fuels code BISON code as part of BISON's fission gas release model. The transport of fission gas from within the fuel grains to the grain boundaries (intra-granular fission gas release) is a fundamental controlling mechanism of fission gas release and gaseous swelling in nuclear fuel. Hence, accurate numerical solution of the corresponding mathematical problem needs to be included in fission gas behaviour models used in fuel performance codes. Under the assumption of equilibrium between trapping and resolution, the process can be described mathematically by a single diffusion equation for the gas atom concentration in a grain. In this work, we propose a new numerical algorithm (PolyPole-1) to efficiently solve the fission gas diffusion equation in time-varying conditions. The PolyPole-1 algorithm is based on the analytic modal solution of the diffusion equation for constant conditions, with the addition of polynomial corrective terms that embody the information on the deviation from constant conditions. The new algorithm is verified by comparing the results to a finite difference solution over a large number of randomly generated operation histories. Furthermore, comparison to state-of-the-art algorithms used in fuel performance codes demonstrates that the accuracy of the PolyPole-1 solution is superior to other algorithms, with similar computational effort. Finally, the concept of PolyPole-1 may be extended to the solution of the general problem of intra-granular fission gas diffusion during non-equilibrium trapping and resolution, which will be the subject of future work.

  9. How to get cool in the heat: comparing analytic models of halo gas cooling with EAGLE

    CERN Document Server

    Stevens, Adam R H; Contreras, Sergio; Croton, Darren J; Padilla, Nelson D; Schaller, Matthieu; Schaye, Joop; Theuns, Tom

    2016-01-01

    We use the hydrodynamic, cosmological EAGLE simulations to investigate how hot gas in haloes condenses to form and grow galaxies. We select haloes from the simulations that are actively cooling and study the temperature, distribution, and metallicity of their hot, cold, and transitioning `cooling' gas, placing these in context of semi-analytic models. Our selection criteria lead us to focus on Milky Way-like haloes. We find the hot-gas density profiles of the haloes form a progressively stronger core over time, the nature of which can be captured by a beta profile that has a simple dependence on redshift. In contrast, the hot gas that actually cools is broadly consistent with a singular isothermal sphere. We find that cooling gas carries a few times the specific angular momentum of the halo and is offset in spin direction from the rest of the hot gas. The gas loses ~60% of its specific angular momentum during the cooling process, generally remaining greater than that of the halo, and is better aligned with th...

  10. The cooling of shock-compressed primordial gas

    CERN Document Server

    Johnson, J L; Johnson, Jarrett L.; Bromm, Volker

    2006-01-01

    We find that at redshifts z > 10, HD line cooling allows strongly-shocked primordial gas to cool to the temperature of the cosmic microwave background (CMB). This temperature is the minimum value attainable via radiative cooling. Provided that the abundance of HD, normalized to the total number density, exceeds a critical level of ~ 10^{-8}, the CMB temperature floor is reached in a time which is short compared to the Hubble time. We estimate the characteristic masses of stars formed out of shocked primordial gas in the wake of the first supernovae, and resulting from the mergers of dark matter haloes during hierarchical structure formation to be ~ 10 M_{solar}. In addition, we show that cooling by HD enables the primordial gas in relic H II regions to cool to temperatures considerably lower than those reached via H_2 cooling alone. We confirm that HD cooling is unimportant in cases where the primordial gas does not go through an ionized phase, as in the formation process of the very first stars in z ~ 20 min...

  11. Development of cooling and cleaning systems for enhanced gas ...

    African Journals Online (AJOL)

    Development of cooling and cleaning systems for enhanced gas quality for 3.7 ... The pollutants generated from gasification include particulate matter, tars, ... Air and gas flow rates were measured to be 18.8 m3/h and 20.12 kg/h respectively.

  12. Development of cooling and cleaning systems for enhanced gas ...

    African Journals Online (AJOL)

    DR OKE

    The temperature of the gas after developed cooling and cleaning system ... conventional energy sources with renewable energy sources used in hybrid mode .... dry filters 1 and 2) and for air flow across orifice plate. ... Technologies Pvt. Ltd., ... allow the gas to pass through various porous media collecting the particulates of.

  13. Types of gas fluidization of cohesive granular materials.

    Science.gov (United States)

    Valverde, Jose Manuel; Castellanos, Antonio

    2007-03-01

    Some years ago it was shown that gas-fluidized powders may transit from solid-like to fluid-like fluidization prior to bubbling, shedding light on a long-standing controversy on the nature of "homogeneous" fluidization. In this paper it is shown that some gas-fluidized powders may also transit from the fluid-like regime to elutriation, with full suppression of the bubbling regime. We provide a diagram that can be used to predict these types of fluidization exhibited by cohesive powders based on simple phenomenological equations in which particle aggregation due to attractive forces is a key ingredient.

  14. PolyPole-1: An accurate numerical algorithm for intra-granular fission gas release

    Science.gov (United States)

    Pizzocri, D.; Rabiti, C.; Luzzi, L.; Barani, T.; Van Uffelen, P.; Pastore, G.

    2016-09-01

    The transport of fission gas from within the fuel grains to the grain boundaries (intra-granular fission gas release) is a fundamental controlling mechanism of fission gas release and gaseous swelling in nuclear fuel. Hence, accurate numerical solution of the corresponding mathematical problem needs to be included in fission gas behaviour models used in fuel performance codes. Under the assumption of equilibrium between trapping and resolution, the process can be described mathematically by a single diffusion equation for the gas atom concentration in a grain. In this paper, we propose a new numerical algorithm (PolyPole-1) to efficiently solve the fission gas diffusion equation in time-varying conditions. The PolyPole-1 algorithm is based on the analytic modal solution of the diffusion equation for constant conditions, combined with polynomial corrective terms that embody the information on the deviation from constant conditions. The new algorithm is verified by comparing the results to a finite difference solution over a large number of randomly generated operation histories. Furthermore, comparison to state-of-the-art algorithms used in fuel performance codes demonstrates that the accuracy of PolyPole-1 is superior to other algorithms, with similar computational effort. Finally, the concept of PolyPole-1 may be extended to the solution of the general problem of intra-granular fission gas diffusion during non-equilibrium trapping and resolution, which will be the subject of future work.

  15. Symmetry breaking and coarsening of clusters in a prototypical driven granular gas.

    Science.gov (United States)

    Livne, Eli; Meerson, Baruch; Sasorov, Pavel V

    2002-11-01

    Granular hydrodynamics predicts symmetry-breaking instability in a two-dimensional ensemble of nearly elastically colliding smooth hard disks driven, at zero gravity, by a rapidly vibrating sidewall. Supercritical and subcritical symmetry-breaking bifurcations of the stripe state are identified, and the supercritical bifurcation curve is computed. The cluster dynamics proceed as a coarsening process mediated by the gas phase. Well above the bifurcation point the final steady state, selected by coarsening, represents a single strongly localized densely packed "droplet."

  16. Symmetry breaking and coarsening of clusters in a prototypical driven granular gas

    OpenAIRE

    Livne, Eli; Meerson, Baruch; Sasorov, Pavel V.

    2002-01-01

    Granular hydrodynamics predicts symmetry-breaking instability in a two-dimensional (2D) ensemble of nearly elastically colliding smooth hard spheres driven, at zero gravity, by a rapidly vibrating sidewall. Super- and subcritical symmetry-breaking bifurcations of the simple clustered state are identified, and the supercritical bifurcation curve is computed. The cluster dynamics proceed as a coarsening process mediated by the gas phase. Far above the bifurcation point the final steady state, s...

  17. Model Selection of Cooling Equipment for Granular Fertilizers%颗粒肥料冷却设备的选型

    Institute of Scientific and Technical Information of China (English)

    李秋萍; 程建伟; 邵国兴

    2011-01-01

    在颗粒肥料生产中,产品的冷却是直接影响产品包装及成品质量的重要过程之一.介绍了转鼓冷却器、流化床冷却器、波面冷却器等几种适合于颗粒肥料冷却的设备,并对它们的工作原理和性能特点作了简单介绍和评述,供用户在设备选型时参考.%In the production of granular fertilizers, product cooling is one of the important processes that affect directly the product packaging and quality. Several cooling facilities are described suitable for granular fertilizers, such as the rotary drum cooler, fluid-bed cooler, wave surface cooler, etc.A brief account and review are given of their working principles and performance characteristics, as a reference for users in their model selection of equipment.

  18. Compatibility of gas turbine materials with steam cooling

    Energy Technology Data Exchange (ETDEWEB)

    Desai, V.; Tamboli, D.; Patel, Y. [Univ. of Central Florida, Orlando, FL (United States)

    1995-10-01

    Gas turbines had been traditionally used for peak load plants and remote locations as they offer advantage of low installation costs and quick start up time. Their use as a base load generator had not been feasible owing to their poor efficiency. However, with the advent of gas turbines based combined cycle plants (CCPs), continued advances in efficiency are being made. Coupled with ultra low NO{sub x} emissions, coal compatibility and higher unit output, gas turbines are now competing with conventional power plants for base load power generation. Currently, the turbines are designed with TIT of 2300{degrees}F and metal temperatures are maintained around 1700{degrees}F by using air cooling. New higher efficiency ATS turbines will have TIT as high as 2700{degrees}F. To withstand this high temperature improved materials, coatings, and advances in cooling system and design are warranted. Development of advanced materials with better capabilities specifically for land base applications are time consuming and may not be available by ATS time frame or may prove costly for the first generation ATS gas turbines. Therefore improvement in the cooling system of hot components, which can take place in a relatively shorter time frame, is important. One way to improve cooling efficiency is to use better cooling agent. Steam as an alternate cooling agent offers attractive advantages because of its higher specific heat (almost twice that of air) and lower viscosity.

  19. Cooling of gas turbines IX : cooling effects from use of ceramic coatings on water-cooled turbine blades

    Science.gov (United States)

    Brown, W Byron; Livingood, John N B

    1948-01-01

    The hottest part of a turbine blade is likely to be the trailing portion. When the blades are cooled and when water is used as the coolant, the cooling passages are placed as close as possible to the trailing edge in order to cool this portion. In some cases, however, the trailing portion of the blade is so narrow, for aerodynamic reasons, that water passages cannot be located very near the trailing edge. Because ceramic coatings offer the possibility of protection for the trailing part of such narrow blades, a theoretical study has been made of the cooling effect of a ceramic coating on: (1) the blade-metal temperature when the gas temperature is unchanged, and (2) the gas temperature when the metal temperature is unchanged. Comparison is also made between the changes in the blade or gas temperatures produced by ceramic coatings and the changes produced by moving the cooling passages nearer the trailing edge. This comparison was made to provide a standard for evaluating the gains obtainable with ceramic coatings as compared to those obtainable by constructing the turbine blade in such a manner that water passages could be located very near the trailing edge.

  20. Applications for Solid Propellant Cool Gas Generator Technology

    Science.gov (United States)

    van der List, M.; van Vliet, L. D.; Sanders, H. M.; Put, P. A. G.; Elst, J. W. E. C.

    2004-10-01

    In 2002 and 2003, Bradford Engineering B.V. conducted, in corporation with the Dutch research institute TNO Prins Maurits Laboratory (PML) a SME study for ESA-ESTEC for the identification of spaceflight applications and on-ground demonstration of Solid Propellant Cool Gas Generator (SPCGG) technology. This innovative technology has been developed by TNO-PML while Bradford Engineering also brought in its experience in spaceflight hardware development and manufacturing. The Solid Propellant Cool Gas Generator (SPCGG) technology allows for pure gas generation at ambient temperatures, as opposed to conventional solid propellant gas generators. This makes the SPCGG technology interesting for a wide range of terrestrial spaceflight applications. During the first part of the study, a variety of potential applications have been identified and three applications were selected for a more detailed quantitative study. In the third phase a ground demonstration was performed successfully for a cold gas propulsion system application. During the actual demonstration test, 10 cool gas generators were mounted and all operated successfully in sequence, demonstrating good repeatability of the produced amount of gas and pressure.

  1. Contribution of HD molecules in cooling of the primordial gas

    CERN Document Server

    Vasiliev, E O; Shchekinov, Yu. A.

    2005-01-01

    We study the effects of HD molecules on thermochemical evolution of the primordial gas behind shock waves, possibly arised in the process of galaxy formation. We find the critical shock velocity when deuterium transforms efficiently into HD molecules which then dominate gas cooling. Above this velocity the shocked gas is able to cool down to the temperature of the cosmic microwave background. Under these conditions the corresponding Jeans mass depends only on redshift and initial density of baryons $M_J \\propto \\delta_c^{-0.5} (1+z)^{0.5}$. At $z\\simgt 45$ HD molecules heat shocked gas, and at larger redshift their contribution to thermal evolution becomes negligible.

  2. Fuel development for gas-cooled fast reactors

    Science.gov (United States)

    Meyer, M. K.; Fielding, R.; Gan, J.

    2007-09-01

    The Generation IV Gas-cooled Fast Reactor (GFR) concept is proposed to combine the advantages of high-temperature gas-cooled reactors (such as efficient direct conversion with a gas turbine and the potential for application of high-temperature process heat), with the sustainability advantages that are possible with a fast-spectrum reactor. The latter include the ability to fission all transuranics and the potential for breeding. The GFR is part of a consistent set of gas-cooled reactors that includes a medium-term Pebble Bed Modular Reactor (PBMR)-like concept, or concepts based on the Gas Turbine Modular Helium Reactor (GT-MHR), and specialized concepts such as the Very High-Temperature Reactor (VHTR), as well as actinide burning concepts [A Technology Roadmap for Generation IV Nuclear Energy Systems, US DOE Nuclear Energy Research Advisory Committee and the Generation IV International Forum, December 2002]. To achieve the necessary high power density and the ability to retain fission gas at high temperature, the primary fuel concept proposed for testing in the United States is dispersion coated fuel particles in a ceramic matrix. Alternative fuel concepts considered in the US and internationally include coated particle beds, ceramic clad fuel pins, and novel ceramic 'honeycomb' structures. Both mixed carbide and mixed nitride-based solid solutions are considered as fuel phases.

  3. International working group on gas-cooled reactors. Summary report

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-15

    The purpose of the meeting was to provide a forum for exchange of information on safety and licensing aspects for gas-cooled reactors in order to provide comprehensive review of the present status and of directions for future applications and development. Contributions were made concerning the operating experience of the Fort St. Vrain (FSV) HTGR Power Plant in the United States of America, the experimental power station Arbeitsgemeinschaft Versuchsreaktor (AVR) in the Federal Republic of Germany, and the CO/sub 2/-cooled reactors in the United Kingdom such as Hunterson B and Hinkley Point B. The experience gained at each of these reactors has proved the high safety potential of Gas-cooled Reactor Power Plants.

  4. Gas Cooled, Natural Uranium, D20 Moderated Power Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Dahlberg, R.C.; Beasley, E.G.; DeBoer, T.K.; Evans, T.C.; Molino, D.F.; Rothwell, W.S.; Slivka, W.R.

    1956-08-01

    The attractiveness of a helium cooled, heavy water moderated, natural uranium central station power plant has been investigated. A fuel element has been devised which allows the D20 to be kept at a low pressure while the exit gas temperature is high. A preliminary cost analysis indicates that, using currently available materials, competitive nuclear power in foreign countries is possible.

  5. Control rod drive for high temperature gas cooled reactor

    Institute of Scientific and Technical Information of China (English)

    DengJun-Xian; XuJi-Ming; 等

    1998-01-01

    This control rod drive is developed for HTR-10 high temperature gas cooled test reactor.The stepmotor is prefered to improve positioning of the control rod and the scram behavior.The preliminary test in 1600170 ambient temperature shows that the selected stepmotor and transmission system can meet the main operation function requirements of HTR-10.

  6. High Temperature Gas-Cooled Test Reactor Options Status Report

    Energy Technology Data Exchange (ETDEWEB)

    Sterbentz, James William [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bayless, Paul David [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-08-01

    Preliminary scoping calculations are being performed for a 100 MWt gas-cooled test reactor. The initial design uses standard prismatic blocks and 15.5% enriched UCO fuel. Reactor physics and thermal-hydraulics simulations have been performed to identify some reactor design features to investigate further. Current status of the effort is described.

  7. Diffusivity and weak clustering in a quasi-two-dimensional granular gas.

    Science.gov (United States)

    Perera-Burgos, J A; Pérez-Ángel, G; Nahmad-Molinari, Y

    2010-11-01

    We present results from a detailed simulation of a quasi-two-dimensional dissipative granular gas, kept in a noncondensed steady state via vertical shaking over a rough substrate. This gas shows a weak power-law decay in the tails of its pair distribution functions, indicating clustering. This clustering depends monotonically on the dissipation coefficient and disappears when the sphere-sphere collisions are conservative. Clustering is also sensitive to the packing fraction. This gas also displays the standard nonequilibrium characteristics of similar systems, including non-Maxwellian velocity distributions. The diffusion coefficients are calculated over all the conditions of the simulations, and it is found that diluted gases are more diffusive for smaller restitution coefficients.

  8. Irregular Oscillation of Bi-disperse Granular Gas in Cyclic Three Compartments

    Institute of Scientific and Technical Information of China (English)

    Sajjad Hussain Shah; LI Yin-Chang; CUI Fei-Fei; ZHANG Qi; Pierre Evesque; HOU Mei-Ying

    2012-01-01

    A 3-D molecular dynamics simulation of a bi-disperse vibro-fluidized granular gas in a cyclic three-compartment cell is performed.A cluster of particles is randomly found in one of the compartments.Lohse's flux model is modified to incorporate inelastic particle-boundary colBsions.This model predicts that periodically there is clustering in each compartment.It is then found that if the model is further modified to incorporate Gaussian white noise,it correctly predicts the non-sequential clustering behavior confirming that there is no chaotic behavior.

  9. Ultrasonic gas accumulation detection and evaluation in nuclear cooling pipes

    Science.gov (United States)

    Yu, Lingyu; Lin, Bin; Shin, Yong-June; Wang, Jingjiang; Tian, Zhenhua

    2012-04-01

    This paper presents a novel ultrasonic guided wave based inspection methodology for detecting and evaluating gas accumulation in nuclear cooling pipe system. The sensing is in-situ by means of low-profile permanently installed piezoelectric wafer sensors to excite interrogating guided waves and to receive the propagating waves in the pipe structure. Detection and evaluation is established through advanced cross time-frequency analysis to extract the phase change in the sensed signal when the gas is accumulating. A correlation between the phase change and the gas amount has been established to provide regulatory prediction capability based on measured sensory data.

  10. Self assembly, mobilization, and flotation of crude oil contaminated sand particles as granular shells on gas bubbles in water.

    Science.gov (United States)

    Tansel, Berrin; Boglaienko, Daria

    2017-01-01

    Contaminant fate and transport studies and models include transport mechanisms for colloidal particles and dissolved ions which can be easily moved with water currents. However, mobilization of much larger contaminated granular particles (i.e., sand) in sediments have not been considered as a possible mechanism due to the relatively larger size of sand particles and their high bulk density. We conducted experiments to demonstrate that oil contaminated granular particles (which exhibit hydrophobic characteristics) can attach on gas bubbles to form granular shells and transfer from the sediment phase to the water column. The interactions and conditions necessary for the oil contaminated granular particles to self assemble as tightly packed granular shells on the gas bubbles which transfer from sediment phase to the water column were evaluated both experimentally and theoretically for South Louisiana crude oil and quartz sand particles. Analyses showed that buoyancy forces can be adequate to move the granular shell forming around the air bubbles if the bubble radius is above 0.001mm for the sand particles with 0.28mm diameter. Relatively high magnitude of the Hamaker constant for the oil film between sand and air (5.81×10(-20)J for air-oil-sand) indicates that air bubbles have high affinity to attach on the oil film that is on the sand particles in comparison to attaching to the sand particles without the oil film in water (1.60×10(-20)J for air-water-sand). The mobilization mechanism of the contaminated granular particles with gas bubbles can occur in natural environments resulting in transfer of granular particles from sediments to the water column. Copyright © 2016 Elsevier B.V. All rights reserved.

  11. AGN-stimulated Cooling of Hot Gas in Elliptical Galaxies

    CERN Document Server

    Valentini, Milena

    2015-01-01

    We study the impact of relatively weak AGN feedback on the interstellar medium of intermediate and massive elliptical galaxies. We find that the AGN activity, while globally heating the ISM, naturally stimulates some degree of hot gas cooling on scales of several kpc. This process generates the persistent presence of a cold ISM phase, with mass ranging between 10$^4$ and $\\gtrsim$ 5 $\\times$ 10$^7$ M$_\\odot$, where the latter value is appropriate for group centered, massive galaxies. Widespread cooling occurs where the ratio of cooling to free-fall time before the activation of the AGN feedback satisfies $t_{cool}/t_{ff} \\lesssim 70$, that is we find a less restrictive threshold than commonly quoted in the literature. This process helps explaining the body of observations of cold gas (both ionized and neutral/molecular) in Ellipticals and, perhaps, the residual star formation detected in many early-type galaxies. The amount and distribution of the off-center cold gas vary irregularly with time. The cold ISM v...

  12. An experimental study of wave propagation and velocity distributions in a vertically driven time-dependent granular gas

    Science.gov (United States)

    Perez, John Anthony

    Averaged over appropriate space and time scales the dynamics of highly fluidized granular systems are often reminiscent of molecular fluid flows. As a result, theoretical efforts to describe these systems have borrowed heavily from continuum mechanics, particularly hydrodynamics. This has led to various proposed granular hydrodynamic theories which have been used to simulate granular materials in various states of confinement and excitation. These studies suggest that a continuum model for granular gasses can accurately reproduce the mean density, velocity and temperature profiles for an experimental granular gas. This thesis contributes to this body of work by presenting an experimental study of the hydrodynamic fields and velocity distributions within a vertically driven quasi-2D granular gas. We have taken pictures as fast as possible of a time-dependent granular gas using a high-speed CCD camera. We have extracted the positions and velocities of 57-564 particles per frame over 400 GB of raw images collected at 3700 fps. We used this data to compute the density, velocity and temperature fields as functions of time and space to a very high resolution. This approach led to the discovery of novel substructures within the hydrodynamic fields which would have been overlooked had we chosen to average over a drive cycle as earlier studies have done. In particular, the high spatial resolution available from our measurements reveals a serrated substructure in the shock waves which has not been reported before. This substructure is the result of collisional momentum transport . One of the current issues in formulating a granular continuum model is how to incorporate local and non-local dependencies between stress and strain correctly. In this thesis we demonstrate that the collisional transfer of momentum produces a non-local effect in the stress tensor which plays a major role in determining the mean flow. Current models have incorporated only the collisional or

  13. A buffer gas cooled beam of barium monohydride

    Science.gov (United States)

    Iwata, Geoffrey; Tarallo, Marco; Zelevinsky, Tanya

    2016-05-01

    Significant advances in direct laser cooling of diatomic molecules have opened up a wide array of molecular species to precision studies spanning many-body physics, quantum collisions and ultracold dissociation. We present a cryogenic beam source of barium monohydride (BaH), and study laser ablation of solid precursor targets as well as helium buffer gas cooling dynamics. Additionally, we cover progress towards a molecular magneto-optical trap, with spectroscopic studies of relevant cooling transitions in the B2 Σ molecules, including resolution of hyperfine structure and precision measurements of the vibrational Frank-Condon factors. Finally, we examine the feasibility of photo dissociation of trapped BaH molecules to yield optically accessible samples of ultracold hydrogen.

  14. Ambient air cooling arrangement having a pre-swirler for gas turbine engine blade cooling

    Science.gov (United States)

    Lee, Ching-Pang; Tham, Kok-Mun; Schroeder, Eric; Meeroff, Jamie; Miller, Jr., Samuel R; Marra, John J

    2015-01-06

    A gas turbine engine including: an ambient-air cooling circuit (10) having a cooling channel (26) disposed in a turbine blade (22) and in fluid communication with a source (12) of ambient air: and an pre-swirler (18), the pre-swirler having: an inner shroud (38); an outer shroud (56); and a plurality of guide vanes (42), each spanning from the inner shroud to the outer shroud. Circumferentially adjacent guide vanes (46, 48) define respective nozzles (44) there between. Forces created by a rotation of the turbine blade motivate ambient air through the cooling circuit. The pre-swirler is configured to impart swirl to ambient air drawn through the nozzles and to direct the swirled ambient air toward a base of the turbine blade. The end walls (50, 54) of the pre-swirler may be contoured.

  15. Joule-Thomson Cooling Due to CO2 Injection into Natural Gas Reservoirs

    OpenAIRE

    Oldenburg, Curtis M.

    2006-01-01

    Depleted natural gas reservoirs are a promising target for Carbon Sequestration with Enhanced Gas Recovery (CSEGR). The focus of this study is on evaluating the importance of Joule-Thomson cooling during CO2 injection into depleted natural gas reservoirs. Joule-Thomson cooling is the adiabatic cooling that accompanies the expansion of a real gas. If Joule-Thomson cooling were extreme, injectivity and formation permeability could be altered by the freezing of residual water, formation of ...

  16. Bouncing, rolling, energy flows, and cluster formation in a two-dimensional vibrated granular gas

    Science.gov (United States)

    Pérez-Ángel, Gabriel; Nahmad-Molinari, Yuri

    2011-10-01

    We study the formation of crystalline clusters for a two-dimensional (2D) sinusoidally vibrated granular gas, with maximum vertical acceleration smaller than gravity, using fully 3D simulations. It is found that this phenomenon arises from the spontaneous segregation of the granulate into two dynamical modes: one of grains that bounce in synchrony with the motion of the sustaining plate (“bouncers”) and another of grains that cease to bounce and simply rolls on the plate, without ever loosing contact with it (“rollers”). These two dynamical categories are quite robust with respect to perturbations. The populations for bouncers and rollers depend on the preparation of the granulate and can be made to take arbitrary values in all the range of accelerations where both dynamical modes are present. It is found that the dynamical mode with the largest population coalesces in clusters under the influence of the other mode, whose grains act as a higher pressure gas that compresses the clusters. In this way it is possible to produce clusters of rollers or clusters of bouncers. A gas made of grains from only one dynamical class shows only weak density fluctuations. When the occupation fractions for both modes are similar, one observes segregation and clusters of both types. The clustering of the gas is monitored using both the average coordination number and the local hexatic order parameter ψ6. Energy flows in the plane are monitored, and it is shown that roller-bouncer collisions increase horizontal kinetic energy, while all other types of collisions reduce this energy. We find that friction with the substrate is the main sink of horizontal energy for these granular gases.

  17. Gas turbine cooling modeling - Thermodynamic analysis and cycle simulations

    Energy Technology Data Exchange (ETDEWEB)

    Jordal, Kristin

    1999-02-01

    Considering that blade and vane cooling are a vital point in the studies of modern gas turbines, there are many ways to include cooling in gas turbine models. Thermodynamic methods for doing this are reviewed in this report, and, based on some of these methods, a number of model requirements are set up and a Cooled Gas Turbine Model (CGTM) for design-point calculations of cooled gas turbines is established. Thereafter, it is shown that it is possible to simulate existing gas turbines with the CGTM. Knowledge of at least one temperature in the hot part of the turbine (TET, TRIT or possibly TIT) is found to be vital for a complete heat balance over the turbine. The losses, which are caused by the mixing of coolant and main flow, are in the CGTM considered through a polytropic efficiency reduction factor S. Through the study of S, it can be demonstrated that there is more to gain from coolant reduction in a small and/or old turbine with poor aerodynamics, than there is to gain in a large, modern turbine, where the losses due to interaction between coolant and main flow are, relatively speaking, small. It is demonstrated, at the design point (TET=1360 deg C, {pi}=20) for the simple-cycle gas turbine, that heat exchanging between coolant and fuel proves to have a large positive impact on cycle efficiency, with an increase of 0.9 percentage points if all of the coolant passes through the heat exchanger. The corresponding improvement for humidified coolant is 0.8 percentage points. A design-point study for the HAT cycle shows that if all of the coolant is extracted after the humidification tower, there is a decrease in coolant requirements of 7.16 percentage points, from 19.58% to 12.52% of the compressed air, and an increase in thermal efficiency of 0.46 percentage points, from 53.46% to 53.92%. Furthermore, it is demonstrated with a TET-parameter variation, that the cooling of a simple-cycle gas turbine with humid air can have a positive effect on thermal efficiency

  18. Intense Atomic and Molecular Beams via Neon Buffer Gas Cooling

    CERN Document Server

    Patterson, David; Doyle, John M

    2008-01-01

    We realize a continuous guided beam of cold deuterated ammonia with a flux of 3e11 ND3 molecules/s and a continuous free-space beam of cold potassium with a flux of 1e16 K atoms/s. A novel feature of the buffer gas source used to produce these beams is cold neon, which, due to intermediate Knudsen number beam dynamics, produces a forward velocity and low-energy tail that is comparable to much colder helium-based sources. We expect this source to be trivially generalizable to a very wide range of atomic and molecular species with significant vapor pressure below 1000 K. This source has properties that make it a good starting point for laser cooling of molecules or atoms, cold collision studies, trapping, or nonlinear optics in buffer-gas-cooled atomic or molecular gases.

  19. Flue gas injection control of silica in cooling towers.

    Energy Technology Data Exchange (ETDEWEB)

    Brady, Patrick Vane; Anderson, Howard L., Jr.; Altman, Susan Jeanne

    2011-06-01

    Injection of CO{sub 2}-laden flue gas can decrease the potential for silica and calcite scale formation in cooling tower blowdown by lowering solution pH to decrease equilibrium calcite solubility and kinetic rates of silica polymerization. Flue gas injection might best inhibit scale formation in power plant cooling towers that use impaired makeup waters - for example, groundwaters that contain relatively high levels of calcium, alkalinity, and silica. Groundwaters brought to the surface for cooling will degas CO{sub 2} and increase their pH by 1-2 units, possibly precipitating calcite in the process. Recarbonation with flue gas can lower the pHs of these fluids back to roughly their initial pH. Flue gas carbonation probably cannot lower pHs to much below pH 6 because the pHs of impaired waters, once outgassed at the surface, are likely to be relatively alkaline. Silica polymerization to form scale occurs most rapidly at pH {approx} 8.3 at 25 C; polymerization is slower at higher and lower pH. pH 7 fluids containing {approx}220 ppm SiO{sub 2} require > 180 hours equilibration to begin forming scale whereas at pH 8.3 scale formation is complete within 36 hours. Flue gas injection that lowers pHs to {approx} 7 should allow substantially higher concentration factors. Periodic cycling to lower recoveries - hence lower silica concentrations - might be required though. Higher concentration factors enabled by flue gas injection should decrease concentrate volumes and disposal costs by roughly half.

  20. High-Temperature Gas-Cooled Test Reactor Point Design

    Energy Technology Data Exchange (ETDEWEB)

    Sterbentz, James William [Idaho National Laboratory; Bayless, Paul David [Idaho National Laboratory; Nelson, Lee Orville [Idaho National Laboratory; Gougar, Hans David [Idaho National Laboratory; Kinsey, James Carl [Idaho National Laboratory; Strydom, Gerhard [Idaho National Laboratory; Kumar, Akansha [Idaho National Laboratory

    2016-04-01

    A point design has been developed for a 200 MW high-temperature gas-cooled test reactor. The point design concept uses standard prismatic blocks and 15.5% enriched UCO fuel. Reactor physics and thermal-hydraulics simulations have been performed to characterize the capabilities of the design. In addition to the technical data, overviews are provided on the technological readiness level, licensing approach and costs.

  1. Explosive injection of gas-particle dispersions into a non-fluidized granular host: volcanological implications

    Science.gov (United States)

    Ross, P.; White, J. D.; Zimanowski, B.; Buettner, R.

    2006-12-01

    Discrete explosive bursts, or explosions, are known from many volcanic eruptions. In maar-diatreme eruptions, they have occurred in debris-filled volcanic vents when magma interacted with groundwater, implying that material mobilized by such explosions passed through the overlying and enclosing debris to reach the surface. Although other studies have addressed the form and characteristics of craters formed by discrete explosions in unconsolidated material, no details are available regarding the structure of the disturbed debris between the explosion site and the crater floor. Field studies of diatreme deposits reveal cross-cutting, steep- sided zones of non-bedded volcaniclastic material that have been inferred to result from "debris jets" driven by explosions. In order to determine the general processes and deposit geometry resulting from discrete, explosive injections of entrained particles through a particulate host, we ran a series of analog experiments in which specific volumes of compressed (5-20 MPa) air were released in bursts that drove gas-particle dispersions through a particulate host. The air expanded into and entrained red particles in a small crucible before moving upward into the white beads used for the host. Injected particles and the overlying host material were glass beads of identical size, shape and density. The experiments revealed that each burst drove into the host an expanding cavity containing air and colored particles, which rapidly collapsed as the driving gas escaped through the permeable roof. Total duration of each run, recorded with high-speed video, was approximately 0.5-1 second. As gas slowed and escaped the cavity the colored beads sedimented into the transient cavity, which was also closing laterally because of inward-directed granular flow of the host. This same behavior was observed even in runs where there was no explosive breaching of the surface, and no colored beads ejected. A columnar body of colored beads was left that

  2. The formation and physical origin of highly ionized cooling gas

    CERN Document Server

    Bordoloi, Rongmon; Norman, Colin A

    2016-01-01

    We present a physically clear cooling flow theory that explains the origin of warm diffuse gas seen primarily as highly ionized absorption line systems in the spectra of background sources. We predict the observed column densities of several highly ionized transitions such as O VI, O VII, Ne VIII, N V, and Mg X; and present a unified comparison of the model predictions with absorption lines seen in the Milky Way disk, Milky Way halo, starburst galaxies, the circumgalactic medium and the intergalactic medium at low and high redshifts. We show that diffuse gas seen in such diverse environments can be simultaneously explained by a simple model of radiatively cooling gas. We show that most of such absorption line systems are consistent with being collisionally ionized, and estimate the maximum likelihood temperature of the gas in each observation. This model satisfactorily explains why O VI is regularly observed around star-forming low-z L* galaxies, and why N V is rarely seen around the same galaxies. We predict...

  3. Compatibility of gas turbine materials with steam cooling

    Energy Technology Data Exchange (ETDEWEB)

    Desai, V.; Tamboli, D.; Patel, Y. [University of Central Florida, Orlando, FL (United States). Dept. of Mechanical and Aerospace Engineering

    1995-12-31

    Objective is to investigate performance of gas turbine materials in steam environment and evaluate remedial measures for alleviating the severity of the problem. Three superalloys commonly used in gas turbines were exposed to 3 steam environments containing different impurity levels for 2 to 6 months. Results: Cr2O3-forming alloys containing 1-4% Al such as IN 738 are susceptible to heavy internal oxidation of Al. High Al (>5%) alloys in which continuous Al2O3 scale can be formed, may not be susceptible to such attack. Deposition of salts from steam will accentuate hot corrosion problems. Alloys with higher Cr content such as X-45 are generally less prone to hot corrosion. The greater damage observed in IN 617 make this alloy less attractive for gas turbines with steam cooling. Electrochemical impedance spectroscopy is a good nondestructive method to evaluate microstructural damage.

  4. Experimental validation of granular dynamics simulations of gas-fluidised beds with homogeneous inflow conditions using Positron Emission Particle Tracking

    NARCIS (Netherlands)

    Hoomans, B.P.B.; Kuipers, J.A.M.; Mohd Salleh, M.; Seville, J.P.

    2001-01-01

    A hard-sphere granular dynamics model of a two-dimensional gas-fluidised bed was experimentally validated using Positron Emission Particle Tracking (PEPT). In the model the Newtonian equations of motion are solved for each solid particle while taking into account the particle¿particle and particle¿w

  5. Heat transfer problems in gas-cooled solid blankets

    Energy Technology Data Exchange (ETDEWEB)

    Fillo, J.A.; Powell, J.R.

    1976-01-01

    In all fusion reactors using the deuterium-tritium fuel cycle, a large fraction approximately 80 percent of the fusion energy will be released as approximately 14 MeV neutrons which must be slowed down in a relatively thick blanket surrounding the plasma, thereby, converting their kinetic energy to high temperature heat which can be continuously removed by a coolant stream and converted in part to electricity in a conventional power turbine. Because of the primary goal of achieving minimum radioactivity, to date Brookhaven blanket concepts have been restricted to the use of some form of solid lithium, with inert gas-cooling and in some design cases, water-cooling of the shell structure. Aluminum and graphite have been identified as very promising structural materials for fusion blankets, and conceptual designs based on these materials have been made. Depending on the thermal loading on the ''first'' wall which surrounds the plasma as well as blanket design, heat transfer problems may be noticeably different in gas-cooled solid blankets. Approaches to solution of heat removal problems as well as explanation of: (a) the after-heat problems in blankets; (b) tritium breeding in solids; and (c) materials selection for radiation shields relative to the minimum activity blanket efforts at Brookhaven are discussed.

  6. Improvements on cool gas generators and their application in space propulsion systems

    NARCIS (Netherlands)

    Sanders, H.M.; Schuurbiers, C.A.H.; Vandeberg, R.J.

    2014-01-01

    Cool Gas Generators are an innovative means to store gas which can be used in propulsion and pressurization systems but also for inflatable structures and terrestrial applications. In Cool Gas Generators, the gas is stored chemically, without pressure or leakage and with a long life time without mai

  7. Beam cooling using a gas-filled RFQ ion guide

    CERN Document Server

    Henry, S; De Saint-Simon, M; Jacotin, M; Képinski, J F; Lunney, M D

    1999-01-01

    A radiofrequency quadrupole mass filter is being developed for use as a high-transmission beam cooler by operating it in buffer gas at high pressure. Such a device will increase the sensitivity of on-line experiments that make use of weakly produced radioactive ion beams. We present simulations and some preliminary measurements for a device designed to cool the beam for the MISTRAL RF mass spectrometer on- line at ISOLDE. The work is carried out partly within the frame of the European Community research network: EXOTRAPS. (9 refs).

  8. Heating and cooling gas-gun targets: nuts and bolts

    Energy Technology Data Exchange (ETDEWEB)

    Gustavsen, Richard L [Los Alamos National Laboratory; Bartram, Brian D [Los Alamos National Laboratory; Gehr, Russell J [HONEYWEL FM& T; Bucholtz, Scott M [HINEYWELL FM& T

    2009-01-01

    The nuts and bolts of a system used to heat and cool gas-gun targets is described. We have now used the system for more than 35 experiments, all of which have used electromagnetic gauging. Features of the system include a cover which is removed (remotely) just prior to projectile impact and the widespread use of metal/polymer insulations. Both the cover and insulation were required to obtain uniform temperatures in samples with low thermal conductivity. The use of inexpensive video cameras to make remote observations of the cover removal was found to be very useful. A brief catalog of useful glue, adhesive tape, insulation, and seal materials is given.

  9. Evaluation of Gas-Cooled Pressurized Phosphoric Acid Fuel Cells for Electric Utility Power Generation

    Science.gov (United States)

    Faroque, M.

    1983-01-01

    Gas cooling is a more reliable, less expensive and a more simple alternative to conventional liquid cooling for heat removal from the phosphoric acid fuel cell (PAFC). The feasibility of gas-cooling was already demonstrated in atmospheric pressure stacks. Theoretical and experimental investigations of gas-cooling for pressurized PAFC are presented. Two approaches to gas cooling, Distributed Gas-Cooling (DIGAS) and Separated Gas-Cooling (SGC) were considered, and a theoretical comparison on the basis of cell performance indicated SGC to be superior to DIGAS. The feasibility of SGC was experimentally demonstrated by operating a 45-cell stack for 700 hours at pressure, and determining thermal response and the effect of other related parameters.

  10. Evaluation of gas cooling for pressurized phosphoric acid fuel cell stacks

    Science.gov (United States)

    Farooque, M.; Skok, A. J.; Maru, H. C.; Kothmann, R. E.; Harry, R. W.

    1983-01-01

    Gas cooling is a more reliable, less expensive and a more simple alternative to conventional liquid cooling for heat removal from the phosphoric acid fuel cell (PAFC). The feasibility of gas cooling has already been demonstrated in atmospheric pressure stacks. This paper presents theoretical and experimental investigation of gas cooling for pressurized PAFC. Two approaches to gas cooling, Distributed Gas Cooling (DIGAS) and Separated Gas Cooling (SGC) were considered, and a theoretical comparison on the basis of cell performance indicated SGC to be superior to DIGAS. The feasibility of SGC was experimentally demonstrated by operating a 45-cell stack for 700 hours at pressure, and determining thermal response and the effect of other related parameters.

  11. Gas-cooled reactors: the importance of their development

    Energy Technology Data Exchange (ETDEWEB)

    Kasten, P.R.

    1979-06-01

    The nearest term GCR is the steam-cycle HTGR, which can be used for both power and process steam production. Use of SC-HTGRs permits timely introduction of thorium fuel cycles and of high-thermal-efficiency reactors, decreasing the need for mined U/sub 3/O/sub 8/ before arrival of symbiotic fueling of fast-thermal reactor systems. The gas-turbine HTGR offers prospects of lower capital costs than other nuclear reactors, but it appears to require longer and more costly development than the SC-HTGR. Accelerated development of the GT-HTGR is needed to gain the advantages of timely introduction. The Gas-Cooled Fast Breeder Reactor (GCFR) offers the possibility of fast breeder reactors with lower capital costs and with higher breeding ratios from oxide fuels. The VHTR provides high-temperature heat for hydrogen production.

  12. Multidisciplinary design optimization of film-cooled gas turbine blades

    Directory of Open Access Journals (Sweden)

    Talya Shashishekara S.

    1999-01-01

    Full Text Available Design optimization of a gas turbine blade geometry for effective film cooling toreduce the blade temperature has been done using a multiobjective optimization formulation. Three optimization formulations have been used. In the first, the average blade temperature is chosen as the objective function to be minimized. An upper bound constraint has been imposed on the maximum blade temperature. In the second, the maximum blade temperature is chosen as the objective function to be minimized with an upper bound constraint on the average blade temperature. In the third formulation, the blade average and maximum temperatures are chosen as objective functions. Shape optimization is performed using geometric parameters associated with film cooling and blade external shape. A quasi-three-dimensional Navier–Stokes solver for turbomachinery flows is used to solve for the flow field external to the blade with appropriate modifications to incorporate the effect of film cooling. The heat transfer analysis for temperature distribution within the blade is performed by solving the heat diffusion equation using the finite element method. The multiobjective Kreisselmeier–Steinhauser function approach has been used in conjunction with an approximate analysis technique for optimization. The results obtained using both formulations are compared with reference geometry. All three formulations yield significant reductions in blade temperature with the multiobjective formulation yielding largest reduction in blade temperature.

  13. Application of Hastelloy X in gas-cooled reactor systems

    Energy Technology Data Exchange (ETDEWEB)

    Brinkman, C.R.; Rittenhouse, P.L.; Corwin, W.R.; Strizak, J.P.; Lystrup, A.; DiStefano, J.R.

    1976-10-01

    Hastelloy X, an Ni--Cr--Fe--Mo alloy, may be an important structural alloy for components of gas-cooled reactor systems. Expected applications of this alloy in the High-Temperature Gas-Cooled Reactor (HTGR) are discussed, and the development of interim mechanical properties and supporting data are reported. Properties of concern include tensile, creep, creep-rupture, fatigue, creep-fatigue interaction, subcritical crack growth, thermal stability, and the influence of helium environments with controlled amounts of impurities on these properties. In order to develop these properties in helium environments that are expected to be prototypic of HTGR operating conditions, it was necessary to construct special environmental test systems. Details of construction and operating parameters are described. Interim results from tests designed to determine the above properties are presented. To date a fairly extensive amount of information has been generated on this material at Oak Ridge National Laboratory and elsewhere concerning behavior in air, which is reviewed. However, only limited data are available from tests conducted in helium. Comparisons of the fatigue and subcritical growth behavior in air between Hastelloy X and a number of other structural alloys are given.

  14. Primordial gas cooling behind shock waves in merging halos

    CERN Document Server

    Vasiliev, E O; Shchekinov, Yu.A.

    2006-01-01

    We investigate thermal regime of the baryons behind shock waves arising in the process of virialization of dark matter halos. We find a fraction of the shocked gas cooled by radiation of HD molecules down to the temperature of the cosmic microwave background (CMB): this fraction increases sharply from about $f_{\\rm c}\\sim 10^{-3}$ for dark halos of $M=5\\times 10^7\\msun$ to $\\sim 0.1$ for halos with $M=10^8\\msun$ at $z=10$. We show, however, that further increase of the mass does not lead to a significant growth of $f_{\\rm c}$ -- the assymptotic value for $M\\gg 10^8\\msun$ is of 0.2. We estimate star formation rate associated with such shock waves, and show that it can be a small but not negligible fraction of the star formation connected with cooling by HI and H$_2$. We argue that extremely metal-poor low-mass stars in the Milky Way may have been formed from primordial gas behind such shocks.

  15. A gas-cooled reactor surface power system

    Science.gov (United States)

    Lipinski, Ronald J.; Wright, Steven A.; Lenard, Roger X.; Harms, Gary A.

    1999-01-01

    A human outpost on Mars requires plentiful power to assure survival of the astronauts. Anywhere from 50 to 500 kW of electric power (kWe) will be needed, depending on the number of astronauts, level of scientific activity, and life-cycle closure desired. This paper describes a 250-kWe power system based on a gas-cooled nuclear reactor with a recuperated closed Brayton cycle conversion system. The design draws upon the extensive data and engineering experience developed under the various high-temperature gas cooled reactor programs and under the SP-100 program. The reactor core is similar in power and size to the research reactors found on numerous university campuses. The fuel is uranium nitride clad in Nb1%Zr, which has been extensively tested under the SP-100 program. The fuel rods are arranged in a hexagonal array within a BeO block. The BeO softens the spectrum, allowing better use of the fuel and stabilizing the geometry against deformation during impact or other loadings. The system has a negative temperature feedback coefficient so that the power level will automatically follow a variable load without the need for continuous adjustment of control elements. Waste heat is removed by an air-cooled heat exchanger using cold Martian air. The amount of radioactivity in the reactor at launch is very small (less than a Curie, and about equal to a truckload of uranium ore). The system will need to be engineered so that criticality can not occur for any launch accident. This system is also adaptable for electric propulsion or life-support during transit to and from Mars.

  16. Nonergodic dynamics of force-free granular gases

    OpenAIRE

    Bodrova, Anna; Chechkin, Aleksei V.; Cherstvy, Andrey G.; Metzler, Ralf

    2015-01-01

    We study analytically and by event-driven molecular dynamics simulations the nonergodic and aging properties of force-free cooling granular gases with both constant and velocity-dependent (viscoelastic) restitution coefficient $\\varepsilon$ for particle pair collisions. We compare the granular gas dynamics with an effective single particle stochastic model based on an underdamped Langevin equation with time dependent diffusivity. We find that both models share the same behavior of the ensembl...

  17. Gas-solute dispersivity ratio in granular porous media as related to particle size distribution and particle shape

    DEFF Research Database (Denmark)

    Pugliese, Lorenzo; Poulsen, Tjalfe; Straface, Salvatore

    2013-01-01

    data. This paper evaluates the possibility for estimating solute dispersion based on gas dispersion measurements. Breakthrough measurements were carried out at different fluid velocities (covering the same range in Reynolds number), using O2 and NaCl as gas and solute tracers, respectively. Three...... different, granular porous materials were used: (1) crushed granite (very angular particles), (2) gravel (particles of intermediate roundness) and (3) Leca® (almost spherical particles). For each material, 21 different particle size fractions were used. Gas and solute dispersion coefficients were determined...

  18. Properties of the homogeneous cooling state of a gas of inelastic rough particles

    Science.gov (United States)

    Reyes, Francisco Vega; Santos, Andres; Kremer, Gilberto M.

    2014-12-01

    In this work we address the question of whether a low-density system composed of identical rough particles may reach hydrodynamic states (also called normal states), even if energy is not conserved in particle collisions. As a way to measure the ability of the system to present a hydrodynamic behavior, we focus on the so-called homogeneous cooling state of the granular gas and look at the corresponding relaxation time as a function of inelasticity and roughness. We report computer simulation results of the sixth- and eighth-order cumulants of the particle velocity distribution function and study the influence of roughness on their relaxation times and asymptotic values. This extends the results of a previous work [Phys. Rev. E 89, 020202(R) (2014], where lower-order cumulants were measured. Our results confirm that the relaxation times are not necessarily longer for stronger inelasticities. This implies that dissipation by itself does not preclude hydrodynamics. It is also observed that the cumulants associated with the angular velocity distribution may reach very high values in a certain region of (small) roughness and that these maxima coincide with small orientational correlation points.

  19. Advanced gas cooled nuclear reactor materials evaluation and development program

    Energy Technology Data Exchange (ETDEWEB)

    1977-01-01

    Results of work performed from January 1, 1977 through March 31, 1977 on the Advanced Gas Cooled Nuclear Reactor Materials Evaluation and Development Program are presented. The objectives of this program are to evaluate candidate alloys for Very High Temperature Reactor (VHTR) Process Heat and Direct Cycle Helium Turbine (DCHT) applications, in terms of the effect of simulated reactor primary coolant (impure Helium), high temperatures, and long time exposures, on the mechanical properties and structural and surface stability of selected candidate alloys. A second objective is to select and recommend materials for future test facilities and more extensive qualification programs. Work covered in this report includes progress to date on alloy selection for VHTR Nuclear Process Heat (NPH) applications and for DCHT applications. The present status on the simulated reactor helium loop design and on designs for the testing and analysis facilities and equipment is discussed.

  20. MELCOR Model Development of High Temperature Gas-cooled Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Changyong; Huh, Changwook [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

    2013-05-15

    The High Temperature Gas-cooled Reactor is one of the major challenging issues on the development of licensing technology for HTGR. The safety evaluation tools of HTGR can be developed in two ways - development of new HTGR-specific codes or revision of existing codes. The KINS is considering using existing analytic tools to the extent feasible, with appropriate modifications for the intended purpose. The system-level MELCOR code is traditionally used for LWR safety analysis, which is capable of performing thermal-fluid and accident analysis, including fission-product transport and release. Recently, this code is being modified for the NGNP HTGR by the NRC. In this study, the MELCOR input model for HTGR with Reactor Cavity Cooling System (RCCS) was developed and the steady state performance was analyzed to evaluate the applicability in HTGR. HTGR model with design characteristics of GT-MHR was developed using MELCOR 2.1 code to validate the applicability of MELCOR code to HTGR. In addition, the steady state of GT-MHR was analyzed with the developed model. It was evaluated to predict well the design parameters of GT-MHR. The developed model can be used as the basis for accident analysis of HTGR with further update of packages such as Radio Nuclide (RN) package.

  1. Physics with Cold Molecules Using Buffer Gas Cooling: Precision Measurement, Collisions, and Laser Cooling

    Science.gov (United States)

    Hutzler, Nicholas R.; Doyle, John M.

    2014-06-01

    Cryogenic buffer gas cooled beams and cells can be used to study many species, from atoms and polar molecules to biomolecules. We report on recent applications of this technique to improve the limit on the electron electric dipole moment [1], load polar molecules into a magnetic trap through optical pumping [2], perform chirally sensitive microwave spectroscopy on polyatomic molecules [3], progress towards magneto-optical trapping of polar molecules [4], and studies of atom-molecule sticking [5]. [1] The ACME Collaboration: J. Baron et al., Science 343, p. 269 (2014) [2] B. Hemmerling et al., arXiv:1310.2669, to appear in Phys. Rev. Lett. [3] D. Patterson, M. Schnell, & J. M. Doyle, Nature 497, p. 475 (2013) [4] H. Lu et al., arXiv:1310.3239, to appear in New. J. Phys. [5] J. Piskorski et al., under preparation

  2. The anisotropy of free path in a vibro-fluidized granular gas

    Science.gov (United States)

    Mei, Yifeng; Chen, Yanpei; Wang, Wei; Hou, Meiying

    2016-08-01

    The free path of a vibro-fluidized two-dimensional (2D) inelastic granular gas confined in a rectangular box is investigated by 2D event-driven molecular simulation. By tracking particles in the simulation, we analyze the local free path. The probability distribution of the free path shows a high tail deviating from the exponential prediction. The anisotropy of the free path is found when we separate the free path to x and y components. The probability distribution of y component is exponential, while x component has a high tail. The probability distribution of angle between the relative velocity and the unit vector joined two particle centers deviates from the distribution of two random vectors, indicating the existence of the dynamic heterogeneities in our system. We explain these results by resorting to the kinetic theory with two-peak velocity distribution. The kinetic theory agrees well with the simulation result. Project supported by the National Basic Research Program of China (Grant No. 2012CB215003), the National Natural Science Foundation of China (Grant No. 91334204), the Fund from the Chinese Academy of Sciences (Grant No. XDA07080100), and China Postdoctoral Science Foundation (Grant No. 2014M561071).

  3. Computational Fluid Dynamics Analysis of Very High Temperature Gas-Cooled Reactor Cavity Cooling System

    Energy Technology Data Exchange (ETDEWEB)

    Frisani, Angelo; Hassan, Yassin A; Ugaz, Victor M

    2010-11-02

    The design of passive heat removal systems is one of the main concerns for the modular very high temperature gas-cooled reactors (VHTR) vessel cavity. The reactor cavity cooling system (RCCS) is a key heat removal system during normal and off-normal conditions. The design and validation of the RCCS is necessary to demonstrate that VHTRs can survive to the postulated accidents. The computational fluid dynamics (CFD) STAR-CCM+/V3.06.006 code was used for three-dimensional system modeling and analysis of the RCCS. A CFD model was developed to analyze heat exchange in the RCCS. The model incorporates a 180-deg section resembling the VHTR RCCS experimentally reproduced in a laboratory-scale test facility at Texas A&M University. All the key features of the experimental facility were taken into account during the numerical simulations. The objective of the present work was to benchmark CFD tools against experimental data addressing the behavior of the RCCS following accident conditions. Two cooling fluids (i.e., water and air) were considered to test the capability of maintaining the RCCS concrete walls' temperature below design limits. Different temperature profiles at the reactor pressure vessel (RPV) wall obtained from the experimental facility were used as boundary conditions in the numerical analyses to simulate VHTR transient evolution during accident scenarios. Mesh convergence was achieved with an intensive parametric study of the two different cooling configurations and selected boundary conditions. To test the effect of turbulence modeling on the RCCS heat exchange, predictions using several different turbulence models and near-wall treatments were evaluated and compared. The comparison among the different turbulence models analyzed showed satisfactory agreement for the temperature distribution inside the RCCS cavity medium and at the standpipes walls. For such a complicated geometry and flow conditions, the tested turbulence models demonstrated that the

  4. Steady state cooling flow models with gas loss for normal elliptical galaxies

    Science.gov (United States)

    Sarazin, Craig L.; Ashe, Gregory A.

    1989-01-01

    A grid of cooling flow models for the hot gas in normal elliptical galaxies is calculated, including the loss of gas due to inhomogeneous cooling. The loss process is modeled as a distributed sink for the gas with the rate of loss being proportional to the local cooling rate. The cooling flow models with gas loss have smaller sonic radii, smaller inflow rates in their central regions, lower densities, and higher temperatures than homogeneous models. The reduction in the amount of hot gas flowing into the center of the models brings the models into much better agreement with the observed X-ray surface brightness profiles of elliptical galaxies. However, there is a large dispersion in the observed X-ray luminosities of ellipticals, and this cannot be explained by variations in the efficiency of gas loss. The gas-loss models have X-ray surface brightness profiles which are much less centrally peaked than the no-gas-loss models.

  5. Low pressure cooling seal system for a gas turbine engine

    Science.gov (United States)

    Marra, John J

    2014-04-01

    A low pressure cooling system for a turbine engine for directing cooling fluids at low pressure, such as at ambient pressure, through at least one cooling fluid supply channel and into a cooling fluid mixing chamber positioned immediately downstream from a row of turbine blades extending radially outward from a rotor assembly to prevent ingestion of hot gases into internal aspects of the rotor assembly. The low pressure cooling system may also include at least one bleed channel that may extend through the rotor assembly and exhaust cooling fluids into the cooling fluid mixing chamber to seal a gap between rotational turbine blades and a downstream, stationary turbine component. Use of ambient pressure cooling fluids by the low pressure cooling system results in tremendous efficiencies by eliminating the need for pressurized cooling fluids for sealing this gap.

  6. Advanced Gas-Cooled Accelerator-Driven Transmutation Experiment. AGATE; Advanced Gas-Cooled Accelerator-Driven Transmutation Experiment. AGATE

    Energy Technology Data Exchange (ETDEWEB)

    Kettler, John; Biss, Klaus [RWTH Aachen (DE). Inst. fuer Nuklearen Brennstoffkreislauf (INBK); Bongardt, Klaus [RWTH Aachen (DE). Inst. fuer Kernphysik (IKP)] (and others)

    2011-07-01

    In Germany the question of final radioactive waste disposal is not yet decided. For intermediate-level radioactive waste the final repository Konrad is licensed, for the high-level radioactive waste not certified repository exists. Transmutation by neutron reaction can reduce the long-term heat output and the amount of long-living radionuclides (minor actinides MA). Several accelerator-driven transmutation concepts have been discussed in the past. The authors describe preliminary results of a feasibility study of the concept AGATE (advanced gas-cooled accelerator-driven transmutation experiment). An accelerated 600 MeV proton beam on the spallation target that is the neutron source in the subcritical reactor. In the starting phase the concept assumes MOX fuel with 20% Pu. In a later phase an optimized fuel for the MA transmutation has to be elaborated.

  7. Improving fuel cycle design and safety characteristics of a gas cooled fast reactor

    NARCIS (Netherlands)

    van Rooijen, W.F.G.

    2006-01-01

    This research concerns the fuel cycle and safety aspects of a Gas Cooled Fast Reactor, one of the so-called "Generation IV" nuclear reactor designs. The Generation IV Gas Cooled Fast Reactor uses helium as coolant at high temperature. The goal of the GCFR is to obtain a "closed nuclear fuel cycle",

  8. Improving fuel cycle design and safety characteristics of a gas cooled fast reactor

    NARCIS (Netherlands)

    van Rooijen, W.F.G.

    2006-01-01

    This research concerns the fuel cycle and safety aspects of a Gas Cooled Fast Reactor, one of the so-called "Generation IV" nuclear reactor designs. The Generation IV Gas Cooled Fast Reactor uses helium as coolant at high temperature. The goal of the GCFR is to obtain a "closed nuclear fuel cycle",

  9. Role of gas cooling in tomorrow`s energy services industry

    Energy Technology Data Exchange (ETDEWEB)

    Hughes, P.J.

    1997-04-01

    This article discusses the marketing approach and opportunities for suppliers and manufacturers of gas cooling equipment to partner with energy service companies (ESCOs). The author`s viewpoint is that in educating and partnering with ESCOs the gas cooling industry enables their technology to reach its potential in the projects that the ESCOs develop.

  10. Role of gas cooling in tomorrow`s energy services industry

    Energy Technology Data Exchange (ETDEWEB)

    Hughes, P.J.

    1997-04-01

    This article discusses the marketing approach and opportunities for suppliers and manufacturers of gas cooling equipment to partner with energy service companies (ESCOs). The author`s viewpoint is that in educating and partnering with ESCOs the gas cooling industry enables their technology to reach its potential in the projects that the ESCOs develop.

  11. A cryogenic buffer gas cooled beam of BaH for molecular laser cooling and ultracold fragmentation

    Science.gov (United States)

    Iwata, Geoffrey; Tarallo, Marco G.; Soerensen, Fabian; Zelevinsky, Tanya

    2015-05-01

    Laser cooled and trapped molecules promise many possibilities to explore a variety of fields such as many-body physics, quantum collisions and dissociation, and precision measurement. We report on an experiment for cooling and trapping barium monohydride (BaH) diatomic molecules. We present a cryogenic buffer gas cooling apparatus for producing a 4 K beam of BaH, and describe the laser cooling schemes necessary to load a molecular magneto-optical trap from that beam. Current progress includes identification of the cooling transitions in the BaH B2 Σ molecules and construction of the molecular beam. The large mass ratio of constituent atoms in BaH makes this system attractive for future studies of ultracold fragmentation, potentially resulting in samples of ultracold hydrogen atoms.

  12. Highly localized clustering states in a granular gas driven by a vibrating wall

    OpenAIRE

    Livne, Eli; Meerson, Baruch; Sasorov, Pavel V.

    2000-01-01

    An ensemble of inelastically colliding grains driven by a vibrating wall in 2D exhibits density clustering. Working in the limit of nearly elastic collisions and employing granular hydrodynamics, we predict, by a marginal stability analysis, a spontaneous symmetry breaking of the extended clustering state (ECS). 2D steady-state solutions found numerically describe localized clustering state (LCSs). Time-dependent granular hydrodynamic simulations show that LCSs can develop from natural initia...

  13. Advanced Combustor Liner Cooling Technology for Gas Turbines

    Directory of Open Access Journals (Sweden)

    Aspi R. Wadia

    1988-10-01

    Full Text Available This paper briefly reviews some of the work on advanced liner cooling techniques - specificially laminated porous wall cooling, angled-multihole (effusion cooling and composite metal matrix liner cooling. The concept definition, heat transfer design procedure and design problems including key materials and fabrication considerations associated with each basic concept will be reviewed. Published rig and engine experience of aircraft engine manufacturers and research organizations will be cited. Some logical extensions of the current liner cooling schemes are suggested for future applications.

  14. Gas-Cooled Fast Reactor (GFR) FY05 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    K. D. Weaver; T. Marshall; T. Totemeier; J. Gan; E.E. Feldman; E.A Hoffman; R.F. Kulak; I.U. Therios; C. P. Tzanos; T.Y.C. Wei; L-Y. Cheng; H. Ludewig; J. Jo; R. Nanstad; W. Corwin; V. G. Krishnardula; W. F. Gale; J. W. Fergus; P. Sabharwall; T. Allen

    2005-09-01

    The gas-cooled fast reactor (GFR) was chosen as one of the Generation IV nuclear reactor systems to be developed based on its excellent potential for sustainability through reduction of the volume and radio toxicity of both its own fuel and other spent nuclear fuel, and for extending/utilizing uranium resources orders of magnitude beyond what the current open fuel cycle can realize. In addition, energy conversion at high thermal efficiency is possible with the current designs being considered, thus increasing the economic benefit of the GFR. However, research and development challenges include the ability to use passive decay heat removal systems during accident conditions, survivability of fuels and in-core materials under extreme temperatures and radiation, and economical and efficient fuel cycle processes. Nevertheless, the GFR was chosen as one of only six Generation IV systems to be pursued based on its ability to meet the Generation IV goals in sustainability, economics, safety and reliability, proliferation resistance and physical protection. Current research and development on the Gas-Cooled Fast Reactor (GFR) has focused on the design of safety systems that will remove the decay heat during accident conditions, ion irradiations of candidate ceramic materials, joining studies of oxide dispersion strengthened alloys; and within the Advanced Fuel Cycle Initiative (AFCI) the fabrication of carbide fuels and ceramic fuel matrix materials, development of non-halide precursor low density and high density ceramic coatings, and neutron irradiation of candidate ceramic fuel matrix and metallic materials. The vast majority of this work has focused on the reference design for the GFR: a helium-cooled, direct power conversion system that will operate with on outlet temperature of 850 C at 7 MPa. In addition to the work being performed in the United States, seven international partners under the Generation IV International Forum (GIF) have identified their interest in

  15. Analysis of Internal Cooling Geometry Variations in Gas Turbine Blades

    Institute of Scientific and Technical Information of China (English)

    M. Eifel; V. Caspary; H. H(o)nen; P. Jeschke

    2009-01-01

    The present investigation analyzes the effects of major geometrical modifications to the interior of a convection cooled gas turbine rotor blade. The main focus lies on the flow of the leading edge channels and the impact on the heat transfer. An experimental approach is performed with flow visualization via paint injection into water. Also numerical calculations are carried out in two sets, on the one hand water calculations accompanying the experi-ments and on the other hand conjugate heat transfer calculations under realistic engine conditions. The latter cal-culations are still ongoing delivering preliminary results. Five geometry configurations are investigated, three of them with differing turbulator arrangements in the leading edge channels. The operating point of the base configuration is set to Re = 50,000 at the inlet while for the modi-fied geometries the pressure ratio is held constant compared to the base. Among several investigated configurations one could be identified that leads to a heat transfer enhancement in one leading edge channel 7 % larger compared to the base.

  16. Description of the magnox type of gas cooled reactor (MAGNOX)

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, S.E.; Nonboel, E

    1999-05-01

    The present report comprises a technical description of the MAGNOX type of reactor as it has been build in Great Britain. The Magnox reactor is gas cooled (CO{sub 2}) with graphite moderators. The fuels is natural uranium in metallic form, canned with a magnesium alloy called 'Magnox'. The Calder Hall Magnox plant on the Lothian coastline of Scotland, 60 km east of Edinburgh, has been chosen as the reference plant and is described in some detail. Data on the other stations are given in tables with a summary of design data. Special design features are also shortly described. Where specific data for Calder Hall Magnox has not been available, corresponding data from other Magnox plants has been used. The information presented is based on the open literature. The report is written as a part of the NKS/RAK-2 sub-project 3: 'Reactors in Nordic Surroundings', which comprises a description of nuclear power plants neighbouring the Nordic countries. (au)

  17. RCCS Experiments and Validation for High Temperature Gas-Cooled Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Chang Oh; Cliff Davis; Goon C. Park

    2007-09-01

    A reactor cavity cooling system (RCCS), an air-cooled helical coil RCCS unit immersed in the water pool, was proposed to overcome the disadvantages of the weak cooling ability of air-cooled RCCS and the complex structure of water-cooled RCCS for the high temperature gas-cooled reactor (HTGR). An experimental apparatus was constructed to investigate the various heat transfer phenomena in the water pool type RCCS, such as the natural convection of air inside the cavity, radiation in the cavity, the natural convection of water in the water pool and the forced convection of air in the cooling pipe. The RCCS experimental results were compared with published correlations. The CFX code was validated using data from the air-cooled portion of the RCCS. The RELAP5 code was validated using measured temperatures from the reactor vessel and cavity walls.

  18. Novel Applications of Buffer-gas Cooling to Cold Atoms, Diatomic Molecules, and Large Molecules

    Science.gov (United States)

    Drayna, Garrett Korda

    Cold gases of atoms and molecules provide a system for the exploration of a diverse set of physical phenomena. For example, cold gasses of magnetically and electrically polar atoms and molecules are ideal systems for quantum simulation and quantum computation experiments, and cold gasses of large polar molecules allow for novel spectroscopic techniques. Buffer-gas cooling is a robust and widely applicable method for cooling atoms and molecules to temperatures of approximately 1 Kelvin. In this thesis, I present novel applications of buffer-gas cooling to obtaining gases of trapped, ultracold atoms and diatomic molecules, as well as the study of the cooling of large organic molecules. In the first experiment of this thesis, a buffer-gas beam source of atoms is used to directly load a magneto-optical trap. Due to the versatility of the buffer-gas beam source, we obtain trapped, sub-milliKelvin gases of four different lanthanide species using the same experimental apparatus. In the second experiment of this thesis, a buffer-gas beam is used as the initial stage of an experiment to directly laser cool and magneto-optically trap the diatomic molecule CaF. In the third experiment of this thesis, buffer-gas cooling is used to study the cooling of the conformational state of large organic molecules. We directly observe conformational relaxation of gas-phase 1,2-propanediol due to cold collisions with helium gas. Lastly, I present preliminary results on a variety of novel applications of buffer-gas cooling, such as mixture analysis, separation of chiral mixtures, the measurement of parity-violation in chiral molecules, and the cooling and spectroscopy of highly unstable reaction intermediates.

  19. Comparative Exergoeconomic Analyses of Gas Turbine Steam Injection Cycles with and without Fogging Inlet Cooling

    OpenAIRE

    Hassan Athari; Saeed Soltani; Marc A. Rosen; Seyed Mohammad Seyed Mahmoudi; Tatiana Morosuk

    2015-01-01

    The results are reported of exergoeconomic analyses of a simple gas turbine cycle without a fogging system (SGT), a simple steam injection gas turbine cycle (STIG), and a steam injection gas turbine cycle with inlet fogging cooler (FSTIG). The results show that (1) a gas-turbine cycle with steam injection and simultaneous cooling has a higher power output than the other considered cycle; (2) at maximum energy efficiency conditions the gas turbine has the highest exergy efficiency of the cycle...

  20. Hydrodynamic modeling of dense gas-fluidised beds using the kinetic theory of granular flow: effect of coefficient of restitution on bed dynamics

    NARCIS (Netherlands)

    Goldschmidt, M.J.V.; Kuipers, J.A.M.; van Swaaij, Willibrordus Petrus Maria

    2000-01-01

    A two-dimensional multi-fluid Eulerian CFD model with closure laws according to the kinetic theory of granular flow has been applied to study the influence of the coefficient of restitution on the hydrodynamics of dense gas-fluidised beds. It is demonstrated that hydrodynamics of dense gas-fluidised

  1. Hydrodynamic modeling of dense gas-fluidised beds using the kinetic theory of granular flow: effect of coefficient of restitution on bed dynamics.

    NARCIS (Netherlands)

    Goldschmidt, M.J.V.; Kuipers, J.A.M.; van Swaaij, Willibrordus Petrus Maria

    2001-01-01

    A two-dimensional multi-fluid Eulerian CFD model with closure laws according to the kinetic theory of granular flow has been applied to study the influence of the coefficient of restitution on the hydrodynamics of dense gas-fluidised beds. It is demonstrated that hydrodynamics of dense gas-fluidised

  2. Hydrodynamic modeling of dense gas-fluidised beds using the kinetic theory of granular flow: effect of coefficient of restitution on bed dynamics

    NARCIS (Netherlands)

    Goldschmidt, M.J.V.; Kuipers, J.A.M.; Swaaij, van W.P.M.

    2000-01-01

    A two-dimensional multi-fluid Eulerian CFD model with closure laws according to the kinetic theory of granular flow has been applied to study the influence of the coefficient of restitution on the hydrodynamics of dense gas-fluidised beds. It is demonstrated that hydrodynamics of dense gas-fluidised

  3. Hydrodynamic modelling of dense gas-fluidised beds using the kinetic theory of granular flow: effect of coefficient of restitution on bed dynamics.

    NARCIS (Netherlands)

    Goldschmidt, M.J.V.; Kuipers, J.A.M.; Swaaij, van W.P.M.

    2001-01-01

    A two-dimensional multi-fluid Eulerian CFD model with closure laws according to the kinetic theory of granular flow has been applied to study the influence of the coefficient of restitution on the hydrodynamics of dense gas-fluidised beds. It is demonstrated that hydrodynamics of dense gas-fluidised

  4. Heating and cooling with gas-fired heat-pumps; Heizen und Kuehlen mit Gas-Waermepumpen

    Energy Technology Data Exchange (ETDEWEB)

    Stadelmann, M.

    2008-07-01

    This article takes a look at the use of gas-fired absorption heat-pumps in combined cooling and heating applications. Savings in investments and reduced primary energy consumption along with the resulting lower gas costs are noted. The operation of such 'reversible' systems that use ammonia as a working fluid is briefly described. An installation at a filling station in Taverne, Switzerland, is described. A further installation at a gas utility depot in Givisiez, Switzerland, is also looked at. Here, the gas-powered heat-pump system works together with a solar installation to provide space-heating and cooling as well as hot-water preparation.

  5. Some Experimental Investigations on Gas Turbine Cooling Performed with Infrared Thermography at Federico II

    Directory of Open Access Journals (Sweden)

    T. Astarita

    2015-01-01

    Full Text Available This paper reviews some experimental measurements of convective heat transfer coefficient distributions which are connected with the cooling of gas turbines, performed by the authors’ research group at the University of Naples Federico II with infrared thermography. Measurements concern impinging jets, cooling of rotating disks, and gas turbine blades, which are either stationary or rotating. The heated thin foil sensor, associated with the detection of surface temperature by means of infrared thermography, is exploited to accurately measure detailed convective heat transfer coefficient maps. The paper also intends to show how to correctly apply the infrared technique in a variety of gas turbines cooling problems.

  6. Use of a temperature-initiated passive cooling system (TIPACS) for the modular high-temperature gas-cooled reactor cavity cooling system (RCCS)

    Energy Technology Data Exchange (ETDEWEB)

    Forsberg, C.W.; Conklin, J.; Reich, W.J.

    1994-04-01

    A new type of passive cooling system has been invented (Forsberg 1993): the Temperature-Initiated Passive Cooling System (TIPACS). The characteristics of the TIPACS potentially match requirements for an improved reactor-cavity-cooling system (RCCS) for the modular high-temperature gas-cooled reactor (MHTGR). This report is an initial evaluation of the TIPACS for the MHTGR with a Rankines (steam) power conversion cycle. Limited evaluations were made of applying the TIPACS to MHTGRs with reactor pressure vessel temperatures up to 450 C. These temperatures may occur in designs of Brayton cycle (gas turbine) and process heat MHTGRs. The report is structured as follows. Section 2 describes the containment cooling issues associated with the MHTGR and the requirements for such a cooling system. Section 3 describes TIPACS in nonmathematical terms. Section 4 describes TIPACS`s heat-removal capabilities. Section 5 analyzes the operation of the temperature-control mechanism that determines under what conditions the TIPACS rejects heat to the environment. Section 6 addresses other design and operational issues. Section 7 identifies uncertainties, and Section 8 provides conclusions. The appendixes provide the detailed data and models used in the analysis.

  7. Perancangan Turbine Inlet Cooling Untuk Meningkatkan Efisiensi Pembangkit Listrik Tenaga Gas Dengan Menggunakan Refrigerasi Absorpsi

    OpenAIRE

    Aditya, Ahmad

    2014-01-01

    Electrical energy plays an important role in the progress of a region, therefore the availability of electrical energy should be a priority. The availability of electricity can be achieved in two ways: the addition of new plants and improve the efficiency of existing plants. In this paper the task, the authors designed a compressor inlet air cooling system or TIC (turbine inlet cooling) on Gas Power Plant with a view to improving the efficiency of the engine. Cooling system ...

  8. SENSITIVE LIMITS ON THE MOLECULAR GAS CONTENT OF CLUSTER COOLING FLOWS

    NARCIS (Netherlands)

    MCNAMARA, BR; JAFFE, W

    1994-01-01

    We have searched for molecular gas toward six cluster cooling flows in the CO(2-1) line using the James Clerk Maxwell Telescope. The sample includes clusters with estimated total cooling rates Of m(CF) approximately 10-600M. yr-1, at redshifts between z approximately 0.01-0.06. None were detected ei

  9. Closed-cycle gas flow system for cooling of high Tc d.c. SQUID magnetometers

    NARCIS (Netherlands)

    Bosch, van den P.J.; Holland, H.J.; Brake, ter H.J.M.; Rogalla, H.

    1995-01-01

    A high Tc.d.c SQUID based magnetometer for magnetocardiography is currently under development at the University of Twente. Since such a magnetometer should be simple to use, the cooling of the system can be realized most practically by means of a cryocooler. A closed-cycle gas flow cooling system in

  10. Effect of Coulomb friction on orientational correlation and velocity distribution functions in a sheared dilute granular gas.

    Science.gov (United States)

    Gayen, Bishakhdatta; Alam, Meheboob

    2011-08-01

    From particle simulations of a sheared frictional granular gas, we show that the Coulomb friction can have dramatic effects on orientational correlation as well as on both the translational and angular velocity distribution functions even in the Boltzmann (dilute) limit. The dependence of orientational correlation on friction coefficient (μ) is found to be nonmonotonic, and the Coulomb friction plays a dual role of enhancing or diminishing the orientational correlation, depending on the value of the tangential restitution coefficient (which characterizes the roughness of particles). From the sticking limit (i.e., with no sliding contact) of rough particles, decreasing the Coulomb friction is found to reduce the density and spatial velocity correlations which, together with diminished orientational correlation for small enough μ, are responsible for the transition from non-gaussian to gaussian distribution functions in the double limit of small friction (μ→0) and nearly elastic particles (e→1). This double limit in fact corresponds to perfectly smooth particles, and hence the maxwellian (gaussian) is indeed a solution of the Boltzmann equation for a frictional granular gas in the limit of elastic collisions and zero Coulomb friction at any roughness. The high-velocity tails of both distribution functions seem to follow stretched exponentials even in the presence of Coulomb friction, and the related velocity exponents deviate strongly from a gaussian with increasing friction.

  11. Ultra-low-temperature cooling of two-dimensional electron gas

    Science.gov (United States)

    Xia, J. S.; Adams, E. D.; Shvarts, V.; Pan, W.; Stormer, H. L.; Tsui, D. C.

    2000-05-01

    A new design has been used for cooling GaAs/Al xGa 1- xAs sample to ultra-low-temperatures. The sample, with electrical contacts directly soldered to the sintered silver powder heat exchangers, was immersed in liquid 3He, which was cooled by a PrNI 5 nuclear refrigerator. The data analysis shows that the two-dimensional electron gas (2DEG) was cooled to 4.0 mK at the refrigerator base temperature Tb of 2.0 mK. The design with heat exchanger cooling is applicable to any ultra-low-temperature transport measurements of 2DEG system.

  12. Cooling system having reduced mass pin fins for components in a gas turbine engine

    Science.gov (United States)

    Lee, Ching-Pang; Jiang, Nan; Marra, John J

    2014-03-11

    A cooling system having one or more pin fins with reduced mass for a gas turbine engine is disclosed. The cooling system may include one or more first surfaces defining at least a portion of the cooling system. The pin fin may extend from the surface defining the cooling system and may have a noncircular cross-section taken generally parallel to the surface and at least part of an outer surface of the cross-section forms at least a quartercircle. A downstream side of the pin fin may have a cavity to reduce mass, thereby creating a more efficient turbine airfoil.

  13. Prediction of Film Cooling on Gas Turbine Airfoils

    Science.gov (United States)

    Garg, Vijay K.; Gaugler, Raymond E.

    1994-01-01

    A three-dimensional Navier-Stokes analysis tool has been developed in order to study the effect of film cooling on the flow and heat transfer characteristics of actual turbine airfoils. An existing code (Arnone et al., 1991) has been modified for the purpose. The code is an explicit, multigrid, cell-centered, finite volume code with an algebraic turbulence model. Eigenvalue scaled artificial dissipation and variable-coefficient implicit residual smoothing are used with a full-multigrid technique. Moreover, Mayle's transition criterion (Mayle, 1991) is used. The effects of film cooling have been incorporated into the code in the form of appropriate boundary conditions at the hole locations on the airfoil surface. Each hole exit is represented by several control volumes, thus providing an ability to study the effect of hole shape on the film-cooling characteristics. Comparison is fair with near mid-span experimental data for four and nine rows of cooling holes, five on the shower head, and two rows each on the pressure and suction surfaces. The computations, however, show a strong spanwise variation of the heat transfer coefficient on the airfoil surface, specially with shower-head cooling.

  14. Performance analysis of a combined cycle gas turbine power plant by using various inlet air cooling systems

    Energy Technology Data Exchange (ETDEWEB)

    Rahim, Murad A. [Department of Mechanical Engineering, Gazi University (Turkey)], e-mail: mrahim@gazi.edu.tr

    2011-07-01

    In recent years, the use of gas turbines in combined cycle power plants has increased. Turbine inlet air cooling appears to be the best solution for maximizing both production and efficiency, particularly in a hot climate. The aim of this study is to determine the impact of different air cooling systems on the gas turbine's performance and carbon dioxide emissions. Computer simulations were carried out, using the THERMOFLEX program, on fogging, evaporative cooling, adsorption cooling, and electrical chiller cooling systems as well as on a base case without cooling system. Results showed that inlet air cooling systems are effective in increasing the efficiency of gas turbine power plants. In addition it was found that absorption chillers are the best system for increasing power generation but that economic and source analyses should be conducted before installing a cooling system. This paper demonstrated that inlet air cooling systems have the ability to increase net power generation of gas turbine power plants.

  15. Fast Quasi-Adiabatic Gas Cooling: An Experiment Revisited

    Science.gov (United States)

    Oss, S.; Gratton, L. M.; Calza, G.; Lopez-Arias, T.

    2012-01-01

    The well-known experiment of the rapid expansion and cooling of the air contained in a bottle is performed with a rapidly responsive, yet very cheap thermometer. The adiabatic, low temperature limit is approached quite closely and measured with our apparatus. A straightforward theoretical model for this process is also presented and discussed.…

  16. The Accretion and Cooling of Preheated Gas in Dark Matter Halos

    CERN Document Server

    Lu, Y; Lu, Yu

    2006-01-01

    (abridged) We use a one-dimensional hydrodynamical code to investigate the effects of preheating on gas accretion and cooling in cold dark matter halos. In the absence of radiative cooling, preheating reduces the amount of gas that can be accreted into a halo, and the accreted gas fraction is determined by the ratio of the initial specific entropy of the gas to the virial entropy of the halo. In the presence of radiative cooling, preheating affects the gas fraction that can cool in two different ways. For small halos with masses 10^13Msun. We suggest that this may be the reason why the stellar mass function of galaxies breaks sharply at the massive end. Such preheating also helps create the hot diffused halos within which the "radio mode" feedback of AGNs can act effectively. In the second case, we assume the intergalactic medium is warm. Here the total amount of gas that can cool in a halo scales with halo mass as ~M^2, as would be required to match the observed stellar- and HI-mass functions in the current ...

  17. Model tests on cooling of gas turbine blades

    Energy Technology Data Exchange (ETDEWEB)

    Hosenfeld, H.G.; von Schwerdtner, O.A. (Kraftwerk Union A.G., Muelheim an der Ruhr (Germany, F.R.). Versuchswesen)

    1979-01-01

    The experimental handling of the blade cooling problems requires test facilities suited to each particular problem in order to obtain an independent variation of influence values. To carry out investigations with the high temperatures of the actual machine, however, would necessitate expenditure of time and money. Consideration of the Law of Similarity results in a reduction in temperature and pressure. A test arrangement is shown and typical results are explained by means of examples.

  18. Simulation of Impinging Cooling Performance with Pin Fins and Mist Cooling Adopted in a Simplified Gas Turbine Transition Piece

    Directory of Open Access Journals (Sweden)

    Tao Xu

    2014-01-01

    Full Text Available The gas turbine transition piece was simplified to a one-four cylinder double chamber model with a single row of impinging holes in the outer wall. Heat transfer augmentation in the coolant chamber was achieved through the use of pin fin structure and mist cooling, which could increase the turbulence and heat transfer efficiency. The present research is focused on heat transfer and pressure characteristics of the impinging cooling in the coolant chamber using FLUENT software. With the given diameter of impinging hole, pin fin diameter ratios D/d have been numerically studied in ranges from 1 to 2. Three different detached L were simulated. The impinging cooling performance in all cases was compared between single-phase and two-phase (imported appropriate mist flow in the coolant chamber. All the simulation results reveal that the factors of L and D/d have significant effects on the convective heat transfer. After the pin fin structure was taken, the resulting temperature decrease of 38.77 K at most compared with the result of structure without pin fins. And with the mist injecting into the cooling chamber, the area weighted average temperature got a lower value without excess pressure loss, which could satisfy the more stringent requirements in engineering.

  19. Method of cooling gas only nozzle fuel tip

    Science.gov (United States)

    Bechtel, William Theodore; Fitts, David Orus; DeLeonardo, Guy Wayne

    2002-01-01

    A diffusion flame nozzle gas tip is provided to convert a dual fuel nozzle to a gas only nozzle. The nozle tip diverts compressor discharge air from the passage feeding the diffusion nozzle air swirl vanes to a region vacated by removal of the dual fuel components, so that the diverted compressor discharge air can flow to and through effusion holes in the end cap plate of the nozzle tip. In a preferred embodiment, the nozzle gas tip defines a cavity for receiving the compressor discharge air from a peripheral passage of the nozzle for flow through the effusion openings defined in the end cap plate.

  20. A review of gas-cooled reactor concepts for SDI (Strategic Defense Initiative) applications

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, A.C.

    1989-08-01

    We have completed a review of multimegawatt gas-cooled reactor concepts proposed for SDI applications. Our study concluded that the principal reason for considering gas-cooled reactors for burst-mode operation was the potential for significant system mass savings over closed-cycle systems if open-cycle gas-cooled operation (effluent exhausted to space) is acceptable. The principal reason for considering gas-cooled reactors for steady-state operation is that they may represent a lower technology risk than other approaches. In the review, nine gas-cooled reactor concepts were compared to identify the most promising. For burst-mode operation, the NERVA (Nuclear Engine for Rocket Vehicle Application) derivative reactor concept emerged as a strong first choice since its performance exceeds the anticipated operational requirements and the technology has been demonstrated and is retrievable. Although the NERVA derivative concepts were determined to be the lead candidates for the Multimegawatt Steady-State (MMWSS) mode as well, their lead over the other candidates is not as great as for the burst mode. 90 refs., 2 figs., 10 tabs.

  1. Blow up Analysis for Anomalous Granular Gases

    CERN Document Server

    Rey, Thomas

    2011-01-01

    We investigate in this article the long-time behaviour of the solutions to the energy-dependent, spatially-homogeneous, inelastic Boltzmann equation for hard spheres. This model describes a diluted gas composed of hard spheres under statistical description, that dissipates energy during collisions. We assume that the gas is "anomalous", in the sense that the energy dissipation increases when the temperature decreases. This allows the gas to cool down in finite time. We study the existence, uniqueness and attractiveness of blow up profiles for this model and the cooling law associated, generalizing the classical Haff's Law for granular gases. To this end, we give some new estimates about the third order moment of the inelastic Boltzmann equation with drift term and we introduce new strongly "non-linear" self-similar variables

  2. Novel Applications of Buffer-Gas Cooling to Cold Atoms, Diatomic Molecules, and Large Molecules

    OpenAIRE

    Drayna, Garrett Korda

    2016-01-01

    Cold gases of atoms and molecules provide a system for the exploration of a diverse set of physical phenomena. For example, cold gasses of magnetically and electrically polar atoms and molecules are ideal systems for quantum simulation and quantum computation experiments, and cold gasses of large polar molecules allow for novel spectroscopic techniques. Buffer-gas cooling is a robust and widely applicable method for cooling atoms and molecules to temperatures of approximately 1 Kelvin. In thi...

  3. Interactions between radio sources and X-ray gas at the centers of cooling core clusters

    Science.gov (United States)

    Sarazin, C. L.; Blanton, E. L.; Clarke, T. E.

    Recent Chandra and XMM observations of the interaction of central radio sources and cooling cores in clusters of galaxies will be presented. The clusters studied include A262, A2052, A2626, A113, A2029, A2597, and A4059. The radio sources blow "bubbles" in the X-ray gas, displacing the gas and compressing it into shells around the radio lobes. At the same time, the radio sources are confined by the X-ray gas. At larger radii, "ghost bubbles" are seen which are weak in radio emission except at low frequencies. These may be evidence of previous eruptions of the radio sources. In some cases, buoyantly rising bubbles may entrain cooler X-ray gas from the centers of the cooling cores. Some radio sources previously classified as cluster merger radio relics may actually be displaced radio bubbles from the central radio sources. The relation between the radio bubbles, and cooler gas (10 keV).

  4. Effect of Gas/Steam Turbine Inlet Temperatures on Combined Cycle Having Air Transpiration Cooled Gas Turbine

    Science.gov (United States)

    Kumar, S.; Singh, O.

    2012-10-01

    Worldwide efforts are being made for further improving the gas/steam combined cycle performance by having better blade cooling technology in topping cycle and enhanced heat recovery in bottoming cycle. The scope of improvement is possible through turbines having higher turbine inlet temperatures (TITs) of both gas turbine and steam turbine. Literature review shows that a combined cycle with transpiration cooled gas turbine has not been analyzed with varying gas/steam TITs. In view of above the present study has been undertaken for thermodynamic study of gas/steam combined cycle with respect to variation in TIT in both topping and bottoming cycles, for air transpiration cooled gas turbine. The performance of combined cycle with dual pressure heat recovery steam generator has been evaluated for different cycle pressure ratios (CPRs) varying from 11 to 23 and the selection diagrams presented for TIT varying from 1,600 to 1,900 K. Both the cycle efficiency and specific work increase with TIT for each pressure ratio. For each TIT there exists an optimum pressure ratio for cycle efficiency and specific work. For the CPR of 23 the best cycle performance is seen at a TIT of 1,900 K for maximum steam temperature of 570 °C, which gives the cycle efficiency of 60.9 % with net specific work of 909 kJ/kg.

  5. CFD Model Development and validation for High Temperature Gas Cooled Reactor Cavity Cooling System (RCCS) Applications

    Energy Technology Data Exchange (ETDEWEB)

    Hassan, Yassin [Univ. of Wisconsin, Madison, WI (United Texas A & M Univ., College Station, TX (United States); Corradini, Michael; Tokuhiro, Akira; Wei, Thomas Y.C.

    2014-07-14

    The Reactor Cavity Cooling Systems (RCCS) is a passive safety system that will be incorporated in the VTHR design. The system was designed to remove the heat from the reactor cavity and maintain the temperature of structures and concrete walls under desired limits during normal operation (steady-state) and accident scenarios. A small scale (1:23) water-cooled experimental facility was scaled, designed, and constructed in order to study the complex thermohydraulic phenomena taking place in the RCCS during steady-state and transient conditions. The facility represents a portion of the reactor vessel with nine stainless steel coolant risers and utilizes water as coolant. The facility was equipped with instrumentation to measure temperatures and flow rates and a general verification was completed during the shakedown. A model of the experimental facility was prepared using RELAP5-3D and simulations were performed to validate the scaling procedure. The experimental data produced during the steady-state run were compared with the simulation results obtained using RELAP5-3D. The overall behavior of the facility met the expectations. The facility capabilities were confirmed to be very promising in performing additional experimental tests, including flow visualization, and produce data for code validation.

  6. Cooling of Gas Turbines. 6; Computed Temperature Distribution Through Cross Section of Water-Cooled Turbine Blade

    Science.gov (United States)

    Livingood, John N. B.; Sams, Eldon W.

    1947-01-01

    A theoretical analysis of the cross-sectional temperature distribution of a water-cooled turbine blade was made using the relaxation method to solve the differential equation derived from the analysis. The analysis was applied to specific turbine blade and the studies icluded investigations of the accuracy of simple methods to determine the temperature distribution along the mean line of the rear part of the blade, of the possible effect of varying the perimetric distribution of the hot gas-to -metal heat transfer coefficient, and of the effect of changing the thermal conductivity of the blade metal for a constant cross sectional area blade with two quarter inch diameter coolant passages.

  7. Implementation of gas district cooling and cogeneration systems in Malaysia; Mise en oeuvre de systemes de gas district cooling et de cogeneration en Malaisie

    Energy Technology Data Exchange (ETDEWEB)

    Haron, S. [Gas District Cooling, M, Sdn Bhd (Malaysia)

    2000-07-01

    With its energy demand in the early 1990's growing at a high rate due to the country's strong economic growth, Malaysia studied various options to improve the efficiency of its energy use. Since its natural gas reserves are almost four times that of its crude oil reserves, efforts were therefore centered on seeking ways to boost the use of natural gas to mitigate the growing domestic energy need. PETRONAS, the national oil company, subsequently studied and chose the District Cooling System using natural gas as the primary source of fuel. The Kuala Lumpur City Center development, which houses the PETRONAS Twin Towers, was subsequently chosen as the first project to use the Gas District Cooling (GDC) System. To acquire the technology and implement this project, PETRONAS created a new subsidiary, Gas District Cooling (Malaysia) Sendirian Berhad (GDC(M)). In the process of improving the plant's efficiency, GDC(M) discovered that the GDC system's efficiency and project economics would be significantly enhanced if its is coupled to a Cogeneration system. Having proven the success of the GDC/Cogeneration system, GDC(M) embarked on a campaign to aggressively promote and seek new opportunities to implement the system, both in Malaysia-and abroad. Apart from enhancing efficiency of energy use, and providing better project economics, the GDC/Cogeneration system also is environment friendly. Today, the GDC/Cogeneration systems is the system of choice for several important developments in Malaysia, which also includes the country's prestigious projects such as the Kuala Lumpur International Airport and the New Federal Government Administrative Center in Putrajaya. (author)

  8. Efficiency of gas cooling and accretion at the disc-corona interface

    Science.gov (United States)

    Armillotta, L.; Fraternali, F.; Marinacci, F.

    2016-11-01

    In star-forming galaxies, stellar feedback can have a dual effect on the circumgalactic medium both suppressing and stimulating gas accretion. The trigger of gas accretion can be caused by disc material ejected into the halo in the form of fountain clouds and by its interaction with the surrounding hot corona. Indeed, at the disc-corona interface, the mixing between the cold/metal-rich disc gas (T ≲ 104 K) and the hot coronal gas (T ≳ 106 K) can dramatically reduce the cooling time of a portion of the corona and produce its condensation and accretion. We studied the interaction between fountain clouds and corona in different galactic environments through parsec-scale hydrodynamical simulations, including the presence of thermal conduction, a key mechanism that influences gas condensation. Our simulations showed that the coronal gas condensation strongly depends on the galactic environment, in particular it is less efficient for increasing virial temperature/mass of the haloes where galaxies reside and it is fully ineffective for objects with virial masses larger than 1013 M⊙. This result implies that the coronal gas cools down quickly in haloes with low-intermediate virial mass (Mvir ≲ 3 × 1012 M⊙) but the ability to cool the corona decreases going from late-type to early-type disc galaxies, potentially leading to the switching off of accretion and the quenching of star formation in massive systems.

  9. Summary of research and development effort on air and water cooling of gas turbine blades

    Energy Technology Data Exchange (ETDEWEB)

    Fraas, A.P.

    1980-03-01

    The review on air- and water-cooled gas turbines from the 1904 Lemale-Armengaud water-cooled gas turbine, the 1948 to 1952 NACA work, and the program at GE indicates that the potential of air cooling has been largely exploited in reaching temperatures of 1100/sup 0/C (approx. 2000/sup 0/F) in utility service and that further increases in turbine inlet temperature may be obtained with water cooling. The local heat flux in the first-stage turbine rotor with water cooling is very high, yielding high-temperature gradients and severe thermal stresses. Analyses and tests indicate that by employing a blade with an outer cladding of an approx. 1-mm-thick oxidation-resistant high-nickel alloy, a sublayer of a high-thermal-conductivity, high-strength, copper alloy containing closely spaced cooling passages approx. 2 mm in ID to minimize thermal gradients, and a central high-strength alloy structural spar, it appears possible to operate a water-cooled gas turbine with an inlet gas temperature of 1370/sup 0/C. The cooling-water passages must be lined with an iron-chrome-nickel alloy must be bent 90/sup 0/ to extend in a neatly spaced array through the platform at the base of the blade. The complex geometry of the blade design presents truly formidable fabrication problems. The water flow rate to each of many thousands of coolant passages must be metered and held to within rather close limits because the heat flux is so high that a local flow interruption of only a few seconds would lead to a serious failure.Heat losses to the cooling water will run approx. 10% of the heat from the fuel. By recoverying this waste heat for feedwater heating in a command cycle, these heat losses will give a degradation in the power plant output of approx. 5% relative to what might be obtained if no cooling were required. However, the associated power loss is less than half that to be expected with an elegant air cooling system.

  10. Granular dynamics simulation of segregation phenomena in bubbling gas-fluidised beds

    NARCIS (Netherlands)

    Hoomans, B.P.B.; Kuipers, J.A.M.; Swaaij, van W.P.M.

    2000-01-01

    A hard-sphere discrete particle model of a gas-fluidised bed was used in order to simulate segregation phenomena in systems consisting of particles of different sizes. In the model, the gas-phase hydrodynamics is described by the spatially averaged Navier¿Stokes equations for two-phase flow. For eac

  11. Heating and cooling system for an on-board gas adsorbent storage vessel

    Energy Technology Data Exchange (ETDEWEB)

    Tamburello, David A.; Anton, Donald L.; Hardy, Bruce J.; Corgnale, Claudio

    2017-06-20

    In one aspect, a system for controlling the temperature within a gas adsorbent storage vessel of a vehicle may include an air conditioning system forming a continuous flow loop of heat exchange fluid that is cycled between a heated flow and a cooled flow. The system may also include at least one fluid by-pass line extending at least partially within the gas adsorbent storage vessel. The fluid by-pass line(s) may be configured to receive a by-pass flow including at least a portion of the heated flow or the cooled flow of the heat exchange fluid at one or more input locations and expel the by-pass flow back into the continuous flow loop at one or more output locations, wherein the by-pass flow is directed through the gas adsorbent storage vessel via the by-pass line(s) so as to adjust an internal temperature within the gas adsorbent storage vessel.

  12. Study on the performance of solar/natural gas absorption cooling chillers

    Energy Technology Data Exchange (ETDEWEB)

    Gomri, Rabah [Laboratory of Genie Climatique, Faculty of Engineering, University of Constantine (Algeria)], E-mail: rabahgomri@yahoo.fr

    2011-07-01

    The use of solar energy to drive single effect vapor absorption cooling machines to produce chilled water for air conditioning and provide cooling in summer is investigated in this paper. The system is designed to use solar heat on a preferential basis. Natural gas burners are used for auxiliary power to heat the water on its way to the generator. When solar radiation is insufficient, the natural gas heater is not used but when solar heat is insufficient, it is used as an efficient backup source of heat to maintain the temperature in the generator. The results of a 1-day period of operation are presented in this paper and the overall performance of the absorption chiller system is analyzed and discussed. The proposed energy system greatly reduces electricity costs, compensates the peak-valley load difference, and reduces CO2 gas emissions since the amount of natural gas used to provide the auxiliary load is very small.

  13. Neutral gas sympathetic cooling of an ion in a Paul trap

    CERN Document Server

    Chen, Kuang; Hudson, Eric R

    2013-01-01

    A single ion immersed in a neutral buffer gas is studied. An analytical model is developed that gives a complete description of the dynamics and steady-state properties of the ions. An extension of this model, using techniques borrowed from the mathematics of finance, is used to explain the recent observation of non-Maxwellian statistics for these systems. Taken together, these results offer an explanation of the longstanding issues associated with sympathetic cooling of an ion by a neutral buffer gas.

  14. Circulating and plateout activity program for gas-cooled reactors with arbitrary radioactive chains

    Energy Technology Data Exchange (ETDEWEB)

    Apperson, C.E. Jr.

    1978-03-01

    A time-dependent method for estimating the fuel body, circulating, plateout, and filter inventory of a high temperature gas-cooled reactor (HTGR) during normal operation is discussed. The primary coolant model accounts for the source, buildup, decay, and cleanup of isotopes that are gas borne inside the prestressed concrete reactor vessel (PCRV). This method has been implemented in the SUVIUS computer program that is described in detail.

  15. Thermoregulated Nitric Cryosystem for Cooling Gas-Filled Detectors of Ionizing Radiation

    Directory of Open Access Journals (Sweden)

    Zharkov I.P.

    2015-09-01

    Full Text Available Cryosystem for cooling and filling of gas-filled detectors of ionizing radiation with compressed inert gas on the basis of wide-nitrogen cryostat, which provides detetector temperature control in a range of 173 — 293 K and its stabilization with accuracy of ± 1°. The work was carried out within the Ukraine — NATO Program of Collaboration, Grant SfP #984655.

  16. Cool core cycles: Cold gas and AGN jet feedback in cluster cores

    CERN Document Server

    Prasad, Deovrat; Babul, Arif

    2015-01-01

    Using high-resolution 3-D and 2-D (axisymmetric) hydrodynamic simulations in spherical geometry, we study the evolution of cool cluster cores heated by feedback-driven bipolar active galactic nuclei (AGN) jets. Condensation of cold gas, and the consequent enhanced accretion, is required for AGN feedback to balance radiative cooling with reasonable efficiencies, and to match the observed cool core properties. A feedback efficiency (mechanical luminosity $\\approx \\epsilon \\dot{M}_{\\rm acc} c^2$; where $\\dot{M}_{\\rm acc}$ is the mass accretion rate at 1 kpc) as small as $5 \\times 10^{-5}$ is sufficient to reduce the cooling/accretion rate by $\\sim 10$ compared to a pure cooling flow. This value is smaller compared to the ones considered earlier, and is consistent with the jet efficiency and the fact that only a small fraction of gas at 1 kpc is accreted on to the supermassive black hole (SMBH). We find hysteresis cycles in all our simulations with cold mode feedback: {\\em condensation} of cold gas when the ratio...

  17. Non-Gaussian and Clustering Behavior in One-Dimensional Polydisperse Granular Gas System

    Institute of Scientific and Technical Information of China (English)

    CHEN Zhi-Yuan; ZHANG Duan-Ming; ZHONG Zhi-Cheng; LI Rui

    2007-01-01

    We present a one-dimensional dynamic model of polydisperse granular mixture with the fractal characteristic of the particle size distribution, in which the particles are subject to inelastic mutual collisions and are driven by Gaussian white noise. The inhomogeneity of the particle size distribution is described by a fractal dimension D. The stationary state that the mixture reaches is the result of the balance between energy dissipation and energy injection. By molecular dynamics simulations, we have mainly studied how the inhomogeneity of the particle size distribution and the inelasticity of collisions influence the velocity distribution and distribution of interparticle spacing in the steady-state.The simulation results indicate that, in the inelasticity case, the velocity distribution strongly deviates from the Gaussian one and the system has a strong spatial clustering. Thus the inhomogeneity and the inelasticity have great effects on the velocity distribution and distribution of interparticle spacing. The quantitative information of the non-Gaussian velocity distribution and that of clustering are respectively represented.

  18. Dwarf Galaxies in Voids: Dark Matter Halos and Gas Cooling

    Directory of Open Access Journals (Sweden)

    Matthias Hoeft

    2010-01-01

    Full Text Available Galaxy surveys have shown that luminous galaxies are mainly distributed in large filaments and galaxy clusters. The remaining large volumes are virtually devoid of luminous galaxies. This is in concordance with the formation of the large-scale structure in the universe as derived from cosmological simulations. However, the numerical results indicate that cosmological voids are abundantly populated with dark matter haloes which may in principle host dwarf galaxies. Observational efforts have in contrast revealed that voids are apparently devoid of dwarf galaxies. We investigate the formation of dwarf galaxies in voids by hydrodynamical cosmological simulations. Due to the cosmic ultraviolet background radiation low-mass haloes show generally a reduced baryon fraction. We determine the characteristic mass below which dwarf galaxies are baryon deficient. We show that the circular velocity below which the accretion of baryons is suppressed is approximately 40 kms−1. The suppressed baryon accretion is caused by the photo-heating due to the UV background. We set up a spherical halo model and show that the effective equation of the state of the gas in the periphery of dwarf galaxies determines the characteristic mass. This implies that any process which heats the gas around dwarf galaxies increases the characteristic mass and thus reduces the number of observable dwarf galaxies.

  19. Gas-cooled fast reactor program. Progress report, January 1, 1980-June 30, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Kasten, P.R.

    1981-09-01

    Since the national Gas-Cooled Fast Breeder Reactor Program has been terminated, this document is the last progress report until reinstatement. It is divided into three sections: Core Flow Test Loop, GCFR shielding and physics, and GCFR pressure vessel and closure studies. (DLC)

  20. Closed Fuel Cycle and Minor Actinide Multirecycling in a Gas-Cooled Fast Reactor

    NARCIS (Netherlands)

    Van Rooijen, W.F.G.; Kloosterman, J.L.

    2009-01-01

    The Generation IV International Forum has identified the Gas-Cooled Fast Reactor (GCFR) as one of the reactor concepts for future deployment. The GCFR targets sustainability, which is achieved by the use of a closed nuclear fuel cycle where only fission products are discharged to a repository; all H

  1. Closed Fuel Cycle and Minor Actinide Multirecycling in a Gas-Cooled Fast Reactor

    NARCIS (Netherlands)

    Van Rooijen, W.F.G.; Kloosterman, J.L.

    2009-01-01

    The Generation IV International Forum has identified the Gas-Cooled Fast Reactor (GCFR) as one of the reactor concepts for future deployment. The GCFR targets sustainability, which is achieved by the use of a closed nuclear fuel cycle where only fission products are discharged to a repository; all

  2. Engineering review of the core support structure of the Gas Cooled Fast Breeder Reactor

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-09-01

    The review of the core support structure of the gas cooled fast breeder reactor (GCFR) covered such areas as the design criteria, the design and analysis of the concepts, the development plan, and the projected manufacturing costs. Recommendations are provided to establish a basis for future work on the GCFR core support structure.

  3. Closed Fuel Cycle and Minor Actinide Multirecycling in a Gas-Cooled Fast Reactor

    NARCIS (Netherlands)

    Van Rooijen, W.F.G.; Kloosterman, J.L.

    2009-01-01

    The Generation IV International Forum has identified the Gas-Cooled Fast Reactor (GCFR) as one of the reactor concepts for future deployment. The GCFR targets sustainability, which is achieved by the use of a closed nuclear fuel cycle where only fission products are discharged to a repository; all H

  4. Migration of radionuclides in a gas cooled solid state spallation target

    DEFF Research Database (Denmark)

    Jørgensen, Thomas; Severin, Gregory; Jensen, Mikael

    2015-01-01

    The current design of the ESS (European Spallation Source) program proposes a rotating solid tungsten target cooled by helium gas and a pulsed beam of protons. For safety reasons any design has to address whether or not the induced radionuclidic isotopes in the target migrate. In this paper we ha...

  5. Granular flow

    DEFF Research Database (Denmark)

    Mitarai, Namiko; Nakanishi, Hiizu

    2012-01-01

    Granular material is a collection of macroscopic particles that are visible with naked eyes. The non-equilibrium nature of the granular materials makes their rheology quite different from that of molecular systems. In this minireview, we present the unique features of granular materials focusing...

  6. Comparative Exergoeconomic Analyses of Gas Turbine Steam Injection Cycles with and without Fogging Inlet Cooling

    Directory of Open Access Journals (Sweden)

    Hassan Athari

    2015-09-01

    Full Text Available The results are reported of exergoeconomic analyses of a simple gas turbine cycle without a fogging system (SGT, a simple steam injection gas turbine cycle (STIG, and a steam injection gas turbine cycle with inlet fogging cooler (FSTIG. The results show that (1 a gas-turbine cycle with steam injection and simultaneous cooling has a higher power output than the other considered cycle; (2 at maximum energy efficiency conditions the gas turbine has the highest exergy efficiency of the cycle components and the lowest value of exergy efficiency is calculated for the fog cooler, where the mixing of air and water at greatly different temperatures causes the high exergy destruction; and (3 utilization of the fogging cooler in the steam injection cycle increases the exergy destruction in the combustion chamber. Furthermore, the simple gas turbine cycle is found to be more economic as its relative cost difference, total unit product cost, and exergoeconomic factors are less than those for the two other configurations. However, its efficiency and net power output are notably lower than for the gas turbine with steam injection and/or fog cooling. The total unit product cost is highest for the simple gas turbine with steam injection.

  7. WASP-80b: a gas giant transiting a cool dwarf

    CERN Document Server

    Triaud, Amaury H M J; Cameron, A Collier; Doyle, A P; Fumel, A; Gillon, M; Hellier, C; Jehin, E; Lendl, M; Lovis, C; Maxted, P F L; Pepe, F; Pollacco, D; Queloz, D; Segransan, D; Smalley, B; Smith, A M S; Udry, S; West, R G; Wheatley, P J; 10.1051/0004-6361/201220900

    2013-01-01

    We report the discovery of a planet transiting the star WASP-80 (1SWASP J201240.26-020838.2; 2MASS J20124017-0208391; TYC 5165-481-1; BPM 80815; V=11.9, K=8.4). Our analysis shows this is a 0.55 +/- 0.04 Mjup, 0.95 +/- 0.03 Rjup gas giant on a circular 3.07 day orbit around a star with a spectral type between K7V and M0V. This system produces one of the largest transit depths so far reported, making it a worthwhile target for transmission spectroscopy. We find a large discrepancy between the v sin i inferred from stellar line broadening and the observed amplitude of the Rossiter-McLaughlin effect. This can be understood either by an orbital plane nearly perpendicular to the stellar spin or by an additional, unaccounted for source of broadening.

  8. How to get cool in the heat: comparing analytic models of hot, cold, and cooling gas in haloes and galaxies with EAGLE

    Science.gov (United States)

    Stevens, Adam R. H.; del P. Lagos, Claudia; Contreras, Sergio; Croton, Darren J.; Padilla, Nelson D.; Schaller, Matthieu; Schaye, Joop; Theuns, Tom

    2017-01-01

    We use the hydrodynamic, cosmological EAGLE simulations to investigate how hot gas in haloes condenses to form and grow galaxies. We select haloes from the simulations that are actively cooling and study the temperature, distribution, and metallicity of their hot, cold, and transitioning `cooling' gas, placing these in context of semi-analytic models. Our selection criteria lead us to focus on Milky Way-like haloes. We find the hot-gas density profiles of the haloes form a progressively stronger core over time, the nature of which can be captured by a β profile that has a simple dependence on redshift. In contrast, the hot gas that will cool over a time-step is broadly consistent with a singular isothermal sphere. We find that cooling gas carries a few times the specific angular momentum of the halo and is offset in spin direction from the rest of the hot gas. The gas loses ˜60% of its specific angular momentum during the cooling process, generally remaining greater than that of the halo, and it precesses to become aligned with the cold gas already in the disc. We find tentative evidence that angular-momentum losses are slightly larger when gas cools onto dispersion-supported galaxies. We show that an exponential surface density profile for gas arriving on a disc remains a reasonable approximation, but a cusp containing ˜20% of the mass is always present, and disc scale radii are larger than predicted by a vanilla Fall & Efstathiou model. These scale radii are still closely correlated with the halo spin parameter, for which we suggest an updated prescription for galaxy formation models.

  9. High Temperature Gas-cooled Reactor Projected Markets and Scoping Economics

    Energy Technology Data Exchange (ETDEWEB)

    Larry Demick

    2010-08-01

    The NGNP Project has the objective of developing the high temperature gas-cooled reactor (HTGR) technology to supply high temperature process heat to industrial processes as a substitute for burning of fossil fuels, such as natural gas. Applications of the HTGR technology that have been evaluated by the NGNP Project for supply of process heat include supply of electricity, steam and high-temperature gas to a wide range of industrial processes, and production of hydrogen and oxygen for use in petrochemical, refining, coal to liquid fuels, chemical, and fertilizer plants.

  10. Formation of martian araneiforms by gas-driven erosion of granular material

    DEFF Research Database (Denmark)

    de Villiers, S.; Nermoen, A.; Jamtveit, B.

    2012-01-01

    Sublimation at the lower surface of a seasonal sheet of translucent CO2 ice at high southern latitudes during the Martian spring, and rapid outflow of the CO2 gas generated in this manner through holes in the ice, has been proposed as the origin of dendritic 100 m–1 km scale branched channels known...

  11. Thermal Hydraulics of the Very High Temperature Gas Cooled Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Chang Oh; Eung Kim; Richard Schultz; Mike Patterson; Davie Petti

    2009-10-01

    The U.S Department of Energy (DOE) is conducting research on the Very High Temperature Reactor (VHTR) design concept for the Next Generation Nuclear Plant (NGNP) Project. The reactor design will be a graphite moderated, thermal neutron spectrum reactor that will produce electricity and hydrogen in a highly efficient manner. The NGNP reactor core will be either a prismatic graphite block type core or a pebble bed core. The NGNP will use very high-burnup, low-enriched uranium, TRISO-coated fuel, and have a projected plant design service life of 60 years. The VHTR concept is considered to be the nearest-term reactor design that has the capability to efficiently produce hydrogen. The plant size, reactor thermal power, and core configuration will ensure passive decay heat removal without fuel damage or radioactive material releases during reactor core-accidents. The objectives of the NGNP Project are to: Demonstrate a full-scale prototype VHTR that is commercially licensed by the U.S. Nuclear Regulatory Commission, and Demonstrate safe and economical nuclear-assisted production of hydrogen and electricity. The DOE laboratories, led by the INL, perform research and development (R&D) that will be critical to the success of the NGNP, primarily in the areas of: • High temperature gas reactor fuels behavior • High temperature materials qualification • Design methods development and validation • Hydrogen production technologies • Energy conversion. This paper presents current R&D work that addresses fundamental thermal hydraulics issues that are relevant to a variety of possible NGNP designs.

  12. WASP-80b: a gas giant transiting a cool dwarf

    Science.gov (United States)

    Triaud, A. H. M. J.; Anderson, D. R.; Collier Cameron, A.; Doyle, A. P.; Fumel, A.; Gillon, M.; Hellier, C.; Jehin, E.; Lendl, M.; Lovis, C.; Maxted, P. F. L.; Pepe, F.; Pollacco, D.; Queloz, D.; Ségransan, D.; Smalley, B.; Smith, A. M. S.; Udry, S.; West, R. G.; Wheatley, P. J.

    2013-03-01

    We report the discovery of a planet transiting the star WASP-80 (1SWASP J201240.26-020838.2; 2MASS J20124017-0208391; TYC 5165-481-1; BPM 80815; V = 11.9, K = 8.4). Our analysis shows this is a 0.55 ± 0.04 Mjup, 0.95 ± 0.03 Rjup gas giant on a circular 3.07 day orbit around a star with a spectral type between K7V and M0V. This system produces one of the largest transit depths so far reported, making it a worthwhile target for transmission spectroscopy. We find a large discrepancy between the vsini⋆ inferred from stellar line broadening and the observed amplitude of the Rossiter-McLaughlin effect. This can be understood either by an orbital plane nearly perpendicular to the stellar spin or by an additional, unaccounted for source of broadening. Using WASP-South photometric observations, from Sutherland (South Africa), confirmed with the 60 cm TRAPPIST robotic telescope, EulerCam, and the CORALIE spectrograph on the Swiss 1.2 m Euler Telescope, and HARPS on the ESO 3.6 m (Prog ID 089.C-0151), all three located at La Silla Observatory, Chile.Radial velocity and photometric data are available in electronic form at the CDS via anonymous ftp to cdsarc.u-strasbg.fr(130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/551/A80

  13. On the connection between radio mini-halos and gas heating in cool core clusters

    CERN Document Server

    Bravi, Luca; Brunetti, Gianfranco

    2016-01-01

    In this work, we present a study of the central regions of cool-core clusters hosting radio mini-halos, which are di use synchrotron sources extended on cluster-scales surrounding the radio-loud brightest galaxy. We aim to investigate the interplay between the thermal and non-thermal components in the intracluster medium in order to get more insights into these radio sources, whose nature is still unclear. It has recently been proposed that turbulence plays a role for heating the gas in cool cores. A correlation between the radio luminosity of mini-halos, $\

  14. Cesium Gas Strongly Confined In One Dimension Sideband Cooling And Collisional Properties

    CERN Document Server

    Bouchoule, I; Petrov, D S; Salomon, C

    2002-01-01

    We study one-dimensional sideband cooling of Cesium atoms strongly confined in a far-detuned optical lattice. The Lamb-Dicke regime is achieved in the lattice direction whereas the transverse confinement is much weaker. The employed sideband cooling method, first studied by Vuletic et al.\\cite{Vule98}, uses Raman transitions between Zeeman levels and produces a spin-polarized sample. We present a detailed study of this cooling method and investigate the role of elastic collisions in the system. We accumulate $83(5)%$ of the atoms in the vibrational ground state of the strongly confined motion, and elastic collisions cool the transverse motion to a temperature of $2.8 \\mu $K=$0.7 \\hbar\\omega_{\\rm osc}/k_{\\rm B}$, where $\\omega_{\\rm osc}$ is the oscillation frequency in the strongly confined direction. The sample then approaches the regime of a quasi-2D cold gas. We analyze the limits of this cooling method and propose a dynamical change of the trapping potential as a mean of cooling the atomic sample to still ...

  15. A combined gas cooled nuclear reactor and fuel cell cycle

    Science.gov (United States)

    Palmer, David J.

    Rising oil costs, global warming, national security concerns, economic concerns and escalating energy demands are forcing the engineering communities to explore methods to address these concerns. It is the intention of this thesis to offer a proposal for a novel design of a combined cycle, an advanced nuclear helium reactor/solid oxide fuel cell (SOFC) plant that will help to mitigate some of the above concerns. Moreover, the adoption of this proposal may help to reinvigorate the Nuclear Power industry while providing a practical method to foster the development of a hydrogen economy. Specifically, this thesis concentrates on the importance of the U.S. Nuclear Navy adopting this novel design for its nuclear electric vessels of the future with discussion on efficiency and thermodynamic performance characteristics related to the combined cycle. Thus, the goals and objectives are to develop an innovative combined cycle that provides a solution to the stated concerns and show that it provides superior performance. In order to show performance, it is necessary to develop a rigorous thermodynamic model and computer program to analyze the SOFC in relation with the overall cycle. A large increase in efficiency over the conventional pressurized water reactor cycle is realized. Both sides of the cycle achieve higher efficiencies at partial loads which is extremely important as most naval vessels operate at partial loads as well as the fact that traditional gas turbines operating alone have poor performance at reduced speeds. Furthermore, each side of the cycle provides important benefits to the other side. The high temperature exhaust from the overall exothermic reaction of the fuel cell provides heat for the reheater allowing for an overall increase in power on the nuclear side of the cycle. Likewise, the high temperature helium exiting the nuclear reactor provides a controllable method to stabilize the fuel cell at an optimal temperature band even during transients helping

  16. Permanent deformation estimates of dynamic equipment foundations: Application to a gas turbine in granular soils

    OpenAIRE

    Galindo Aires, Rubén Ángel; Illueca Jové, Manuel; Jimenez Rodriguez, Rafael

    2014-01-01

    Permanent displacements of a gas turbine founded on a fine, poorly graded, and medium density sand are studied. The amplitudes and modes of vibration are computed using Barkan´s formulation, and the “High-Cycle Accumulation” (HCA) model is employed to account for accumulated deformations due to the high number of cycles. The methodology is simple: it can be easily incorporated into standard mathematical software, and HCA model parameters can be estimated based on granulometry and index proper...

  17. Facility Configuration Study of the High Temperature Gas-Cooled Reactor Component Test Facility

    Energy Technology Data Exchange (ETDEWEB)

    S. L. Austad; L. E. Guillen; D. S. Ferguson; B. L. Blakely; D. M. Pace; D. Lopez; J. D. Zolynski; B. L. Cowley; V. J. Balls; E.A. Harvego, P.E.; C.W. McKnight, P.E.; R.S. Stewart; B.D. Christensen

    2008-04-01

    A test facility, referred to as the High Temperature Gas-Cooled Reactor Component Test Facility or CTF, will be sited at Idaho National Laboratory for the purposes of supporting development of high temperature gas thermal-hydraulic technologies (helium, helium-Nitrogen, CO2, etc.) as applied in heat transport and heat transfer applications in High Temperature Gas-Cooled Reactors. Such applications include, but are not limited to: primary coolant; secondary coolant; intermediate, secondary, and tertiary heat transfer; and demonstration of processes requiring high temperatures such as hydrogen production. The facility will initially support completion of the Next Generation Nuclear Plant. It will secondarily be open for use by the full range of suppliers, end-users, facilitators, government laboratories, and others in the domestic and international community supporting the development and application of High Temperature Gas-Cooled Reactor technology. This pre-conceptual facility configuration study, which forms the basis for a cost estimate to support CTF scoping and planning, accomplishes the following objectives: • Identifies pre-conceptual design requirements • Develops test loop equipment schematics and layout • Identifies space allocations for each of the facility functions, as required • Develops a pre-conceptual site layout including transportation, parking and support structures, and railway systems • Identifies pre-conceptual utility and support system needs • Establishes pre-conceptual electrical one-line drawings and schedule for development of power needs.

  18. Heat transfer technology for internal passages of air-cooled blades for heavy-duty gas turbines.

    Science.gov (United States)

    Weigand, B; Semmler, K; von Wolfersdorf, J

    2001-05-01

    The present review paper, although far from being complete, aims to give an overview about the present state of the art in the field of heat transfer technology for internal cooling of gas turbine blades. After showing some typical modern cooled blades, the different methods to enhance heat transfer in the internal passages of air-cooled blades are discussed. The complicated flows occurring in bends are described in detail, because of their increasing importance for modern cooling designs. A short review about testing of cooling design elements is given, showing the interaction of the different cooling features as well. The special focus of the present review has been put on the cooling of blades for heavy-duty gas turbines, which show several differences compared to aero-engine blades.

  19. Energy of one-dimensional diatomic elastic granular gas: Theory and molecular dynamics Simulation

    CERN Document Server

    Khotimah, Siti Nurul; Widayani,; Waris, Abdul

    2011-01-01

    One-dimensional ideal diatomic gas is simulated through possible types of motion of a molecule. Energy of each type of its motion is calculated from theory and numerical method. Calculation of kinetic energy of an atom in translational-vibrational motion is not analytically simple, but it can be solved by numerical method of molecular dynamic simulation. This paper justifies that kinetic energy of a diatomic molecule can be determined by two different approaches. The first is the sum of kinetic energy of each atom and second is the sum of kinetic energy of translational motion and vibrational motion.

  20. Spitzer Secondary Eclipse Observations of Five Cool Gas Giant Planets and Empirical Trends in Cool Planet Emission Spectra

    CERN Document Server

    Kammer, Joshua A; Line, Michael R; Fortney, Jonathan J; Deming, Drake; Burrows, Adam; Cowan, Nicolas B; Triaud, Amaury H M J; Agol, Eric; Desert, Jean-Michel; Fulton, Benjamin J; Howard, Andrew W; Laughlin, Gregory P; Lewis, Nikole K; Morley, Caroline V; Moses, Julianne I; Showman, Adam P; Todorov, Kamen O

    2015-01-01

    In this work we present Spitzer 3.6 and 4.5 micron secondary eclipse observations of five new cool (<1200 K) transiting gas giant planets: HAT-P-19b, WASP-6b, WASP-10b, WASP-39b, and WASP-67b. We compare our measured eclipse depths to the predictions of a suite of atmosphere models and to eclipse depths for planets with previously published observations in order to constrain the temperature- and mass-dependent properties of gas giant planet atmospheres. We find that the dayside emission spectra of planets less massive than Jupiter require models with efficient circulation of energy to the night side and/or increased albedos, while those with masses greater than that of Jupiter are consistently best-matched by models with inefficient circulation and low albedos. At these relatively low temperatures we expect the atmospheric methane to CO ratio to vary as a function of metallicity, and we therefore use our observations of these planets to constrain their atmospheric metallicities. We find that the most massi...

  1. Penetrating Gas Streams Generate Unrelaxed,Non-Cool-Core Clusters of Galaxies

    CERN Document Server

    Zinger, E; Birnboim, Y; Kravtsov, A; Nagai, D

    2015-01-01

    We utilize cosmological simulations of 16 galaxy clusters at redshifts $z=0$ and $z=0.6$ to study the effect of inflowing streams on the properties of the inner Intra-Cluster Medium (ICM). We find that the mass accretion occurs predominantly along streams that originate from the cosmic web and consist of heated gas. Clusters that are unrelaxed in terms of their X-ray morphology are characterized by higher mass inflow rates and deeper penetration of the streams, typically into the inner third of the virial radius. The penetrating streams generate elevated random motions, bulk flows, cold fronts and metal mixing, thus producing Non-Cool-Core clusters. The degree of penetration of the streams may change over time such that clusters can switch from being unrelaxed to relaxed over a time-scale of several Gyrs. The stream properties thus help us understand the distinction between cool-core and non-cool-core clusters.

  2. Flow structure and heat exchange analysis in internal cooling channel of gas turbine blade

    Science.gov (United States)

    Szwaba, Ryszard; Kaczynski, Piotr; Doerffer, Piotr; Telega, Janusz

    2016-08-01

    This paper presents the study of the flow structure and heat transfer, and also their correlations on the four walls of a radial cooling passage model of a gas turbine blade. The investigations focus on heat transfer and aerodynamic measurements in the channel, which is an accurate representation of the configuration used in aeroengines. Correlations for the heat transfer coefficient and the pressure drop used in the design of radial cooling passages are often developed from simplified models. It is important to note that real engine passages do not have perfect rectangular cross sections, but include corner fillet, ribs with fillet radii and special orientation. Therefore, this work provides detailed fluid flow and heat transfer data for a model of radial cooling geometry which possesses very realistic features.

  3. Galaxies Probing Galaxies: Cool Halo Gas from a z = 0.47 Post-Starburst Galaxy

    Science.gov (United States)

    Rubin, Kate H. R.; Prochaska, J. Xavier; Koo, David C.; Phillips, Andrew C.; Weiner, Benjamin J.

    2010-03-01

    We study the cool gas around a galaxy at z = 0.4729 using Keck/LRIS spectroscopy of a bright (B = 21.7) background galaxy at z = 0.6942 at a transverse distance of 16.5h -1 70 kpc. The background galaxy spectrum reveals strong Fe II, Mg II, Mg I, and Ca II absorption at the redshift of the foreground galaxy, with an Mg II λ2796 rest equivalent width of 3.93 ± 0.08 Å, indicative of a velocity width exceeding 400 km s-1. Because the background galaxy is large (>4h -1 70 kpc), the high covering fraction of the absorbing gas suggests that it arises in a spatially extended complex of cool clouds with large velocity dispersion. Spectroscopy of the massive (log M */M sun = 11.15 ± 0.08) host galaxy reveals that it experienced a burst of star formation about 1 Gyr ago and that it harbors a weak active galactic nucleus. We discuss the possible origins of the cool gas in its halo, including multiphase cooling of hot halo gas, cold inflow, tidal interactions, and galactic winds. We conclude that the absorbing gas was most likely ejected or tidally stripped from the interstellar medium of the host galaxy or its progenitors during the past starburst event. Adopting the latter interpretation, these results place one of only a few constraints on the radial extent of cool gas driven or stripped from a galaxy in the distant universe. Future studies with integral field unit spectroscopy of spatially extended background galaxies will provide multiple sight lines through foreground absorbers and permit analysis of the morphology and kinematics of the gas surrounding galaxies with a diverse set of properties and environments. Some of the data presented herein were obtained at the W. M. Keck Observatory, which is operated as a scientific partnership among the California Institute of Technology, the University of California, and the National Aeronautics and Space Administration. The Observatory was made possible by the generous financial support of the W. M. Keck Foundation.

  4. Granular Computing

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    The basic ideas and principles of granular computing (GrC) have been studied explicitly or implicitly in many fields in isolation. With the recent renewed and fast growing interest, it is time to extract the commonality from a diversity of fields and to study systematically and formally the domain independent principles of granular computing in a unified model. A framework of granular computing can be established by applying its own principles. We examine such a framework from two perspectives,granular computing as structured thinking and structured problem solving. From the philosophical perspective or the conceptual level,granular computing focuses on structured thinking based on multiple levels of granularity. The implementation of such a philosophy in the application level deals with structured problem solving.

  5. Decay Heat Removal in GEN IV Gas-Cooled Fast Reactors

    Directory of Open Access Journals (Sweden)

    Lap-Yan Cheng

    2009-01-01

    Full Text Available The safety goal of the current designs of advanced high-temperature thermal gas-cooled reactors (HTRs is that no core meltdown would occur in a depressurization event with a combination of concurrent safety system failures. This study focused on the analysis of passive decay heat removal (DHR in a GEN IV direct-cycle gas-cooled fast reactor (GFR which is based on the technology developments of the HTRs. Given the different criteria and design characteristics of the GFR, an approach different from that taken for the HTRs for passive DHR would have to be explored. Different design options based on maintaining core flow were evaluated by performing transient analysis of a depressurization accident using the system code RELAP5-3D. The study also reviewed the conceptual design of autonomous systems for shutdown decay heat removal and recommends that future work in this area should be focused on the potential for Brayton cycle DHRs.

  6. Comb-assisted cavity ring-down spectroscopy of a buffer-gas-cooled molecular beam.

    Science.gov (United States)

    Santamaria, Luigi; Sarno, Valentina Di; Natale, Paolo De; Rosa, Maurizio De; Inguscio, Massimo; Mosca, Simona; Ricciardi, Iolanda; Calonico, Davide; Levi, Filippo; Maddaloni, Pasquale

    2016-06-22

    We demonstrate continuous-wave cavity ring-down spectroscopy of a partially hydrodynamic molecular beam emerging from a buffer-gas-cooling source. Specifically, the (ν1 + ν3) vibrational overtone band of acetylene (C2H2) around 1.5 μm is accessed using a narrow-linewidth diode laser stabilized against a GPS-disciplined rubidium clock via an optical frequency comb synthesizer. As an example, the absolute frequency of the R(1) component is measured with a fractional accuracy of ∼1 × 10(-9). Our approach represents the first step towards the extension of more sophisticated cavity-enhanced interrogation schemes, including saturated absorption cavity ring-down or two-photon excitation, to buffer-gas-cooled molecular beams.

  7. Cool companies: How the best businesses boost profits and productivity by cutting greenhouse gas emissions

    Energy Technology Data Exchange (ETDEWEB)

    Romm, J.J.

    1999-11-01

    A number of companies see the prospect of reducing greenhouse gas emissions not as a roadblock to growth and innovation but as a unique opportunity to increase profits and productivity. These ``cool`` companies understand the strategic importance of reducing heat-trapping emissions and have worked to cut their emissions by fifty percent or more. In Cool Companies, energy expert Joseph Romm describes the experiences of these remarkable firms, as he presents more than fifty case studies in which bottom line improvements have been achieved by improving processes, increasing energy efficiency, and adopting new technologies. Romm places efforts to reduce emissions in the context of proven corporate strategies, showing managers how they can build or retrofit their operations with the latest technologies to reduce emissions and achieve quick returns on the investment. Case studies explain: the concept of lean production and why systematic efforts to reduce productivity, greatly compounding gains achieved from increased energy efficiency; options for cool power from cogeneration to solar, wind, and geothermal energy; and energy efficiency in manufacturing, including motors and motor systems, steam, and process energy. In profiling successful companies such as DuPont, 3M, Compaq, Xerox, Toyota, Verifone, Perkin-Elmer, and Centerplex, among many others, Cool Companies turns on its head the notion that the effort to combat global warming will come with massive costs to the industrial sector. It is a unique and essential business book for anyone concerned with increasing profits and productivity while reducing a greenhouse gas emissions.

  8. Hydrodynamics for a model of a confined quasi-two-dimensional granular gas.

    Science.gov (United States)

    Brey, J Javier; Buzón, V; Maynar, P; García de Soria, M I

    2015-05-01

    The hydrodynamic equations for a model of a confined quasi-two-dimensional gas of smooth inelastic hard spheres are derived from the Boltzmann equation for the model, using a generalization of the Chapman-Enskog method. The heat and momentum fluxes are calculated to Navier-Stokes order, and the associated transport coefficients are explicitly determined as functions of the coefficient of normal restitution and the velocity parameter involved in the definition of the model. Also an Euler transport term contributing to the energy transport equation is considered. This term arises from the gradient expansion of the rate of change of the temperature due to the inelasticity of collisions, and it vanishes for elastic systems. The hydrodynamic equations are particularized for the relevant case of a system in the homogeneous steady state. The relationship with previous works is analyzed.

  9. High-Fidelity Gas and Granular Flow Physics Models for Rocket Exhaust Interaction with Lunar Soil Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Current modeling of Lunar and Martian soil erosion and debris transport caused by rocket plume impingement lacks essential physics from the peculiar granular...

  10. High Temperature Gas-Cooled Test Reactor Point Design: Summary Report

    Energy Technology Data Exchange (ETDEWEB)

    Sterbentz, James William [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bayless, Paul David [Idaho National Lab. (INL), Idaho Falls, ID (United States); Nelson, Lee Orville [Idaho National Lab. (INL), Idaho Falls, ID (United States); Gougar, Hans David [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kinsey, J. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Strydom, Gerhard [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-03-01

    A point design has been developed for a 200-MW high-temperature gas-cooled test reactor. The point design concept uses standard prismatic blocks and 15.5% enriched uranium oxycarbide fuel. Reactor physics and thermal-hydraulics simulations have been performed to characterize the capabilities of the design. In addition to the technical data, overviews are provided on the technology readiness level, licensing approach, and costs of the test reactor point design.

  11. A modular gas-cooled cermet reactor system for planetary base power

    Science.gov (United States)

    Jahshan, Salim N.; Borkowski, Jeffrey A.

    1993-01-01

    Fission nuclear power is foreseen as the source for electricity in planetary colonization and exploration. A six module gas-cooled, cermet-fueled reactor is proposed that can meet the design objectives. The highly enriched core is compact and can operate at high temperature for a long life. The helium coolant powers six modular Brayton cycles that compare favorably with the SP-100-based Brayton cycle.

  12. Application of gas-cooled Accelerator Driven System (ADS) transmutation devices to sustainable nuclear energy development

    OpenAIRE

    2011-01-01

    The conceptual design of a pebble bed gas-cooled transmutation device is shown with the aim to evaluate its potential for its deployment in the context of the sustainable nuclear energy development, which considers high temperature reactors for their operation in cogeneration mode, producing electricity, heat and Hydrogen. As differential characteristics our device operates in subcritical mode, driven by a neutron source activated by an accelerator that adds clear safety advantages and fuel f...

  13. High Temperature Gas-Cooled Test Reactor Point Design: Summary Report

    Energy Technology Data Exchange (ETDEWEB)

    Sterbentz, James William [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bayless, Paul David [Idaho National Lab. (INL), Idaho Falls, ID (United States); Nelson, Lee Orville [Idaho National Lab. (INL), Idaho Falls, ID (United States); Gougar, Hans David [Idaho National Lab. (INL), Idaho Falls, ID (United States); Strydom, Gerhard [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-01-01

    A point design has been developed for a 200-MW high-temperature gas-cooled test reactor. The point design concept uses standard prismatic blocks and 15.5% enriched uranium oxycarbide fuel. Reactor physics and thermal-hydraulics simulations have been performed to characterize the capabilities of the design. In addition to the technical data, overviews are provided on the technology readiness level, licensing approach, and costs of the test reactor point design.

  14. Thermal-hydraulic code selection for modular high temperature gas-cooled reactors

    Energy Technology Data Exchange (ETDEWEB)

    Komen, E.M.J.; Bogaard, J.P.A. van den

    1995-06-01

    In order to study the transient thermal-hydraulic system behaviour of modular high temperature gas-cooled reactors, the thermal-hydraulic computer codes RELAP5, MELCOR, THATCH, MORECA, and VSOP are considered at the Netherlands Energy Research Foundation ECN. This report presents the selection of the most appropriate codes. To cover the range of relevant accidents, a suite of three codes is recommended for analyses of HTR-M and MHTGR reactors. (orig.).

  15. Neutral gas sympathetic cooling of an ion in a Paul trap.

    Science.gov (United States)

    Chen, Kuang; Sullivan, Scott T; Hudson, Eric R

    2014-04-11

    A single ion immersed in a neutral buffer gas is studied. An analytical model is developed that gives a complete description of the dynamics and steady-state properties of the ions. An extension of this model, using techniques employed in the mathematics of economics and finance, is used to explain the recent observation of non-Maxwellian statistics for these systems. Taken together, these results offer an explanation of the long-standing issues associated with sympathetic cooling of an ion by a neutral buffer gas.

  16. Alternative Liquid Fuel Effects on Cooled Silicon Nitride Marine Gas Turbine Airfoils

    Energy Technology Data Exchange (ETDEWEB)

    Holowczak, J.

    2002-03-01

    With prior support from the Office of Naval Research, DARPA, and U.S. Department of Energy, United Technologies is developing and engine environment testing what we believe to be the first internally cooled silicon nitride ceramic turbine vane in the United States. The vanes are being developed for the FT8, an aeroderivative stationary/marine gas turbine. The current effort resulted in further manufacturing and development and prototyping by two U.S. based gas turbine grade silicon nitride component manufacturers, preliminary development of both alumina, and YTRIA based environmental barrier coatings (EBC's) and testing or ceramic vanes with an EBC coating.

  17. Evaluation of proposed German safety criteria for high-temperature gas-cooled reactors

    Energy Technology Data Exchange (ETDEWEB)

    Barsell, A.W.

    1980-05-01

    This work reviews proposed safety criteria prepared by the German Bundesministerium des Innern (BMI) for future licensing of gas-cooled high-temperature reactor (HTR) concepts in the Federal Republic of Germany. Comparison is made with US General Design Criteria (GDCs) in 10CFR50 Appendix A and with German light water reactor (LWR) criteria. Implications for the HTR design relative to the US design and safety approach are indicated. Both inherent characteristics and design features of the steam cycle, gas turbine, and process heat concepts are taken into account as well as generic design options such as a pebble bed or prismatic core.

  18. Irrigation Induced Surface Cooling in the Context of Modern and Increased Greenhouse Gas Forcing

    Science.gov (United States)

    Cook, Benjamin I.; Puma, Michael J.; Krakauer, Nir Y.

    2010-01-01

    There is evidence that expected warming trends from increased greenhouse gas (GHG) forcing have been locally masked by irrigation induced cooling, and it is uncertain how the magnitude of this irrigation masking effect will change in the future. Using an irrigation dataset integrated into a global general circulation model, we investigate the equilibrium magnitude of irrigation induced cooling under modern (Year 2000) and increased (A1B Scenario, Year 2050) GHG forcing, using modern irrigation rates in both scenarios. For the modern scenario, the cooling is largest over North America, India, the Middle East, and East Asia. Under increased GHG forcing, this cooling effect largely disappears over North America, remains relatively unchanged over India, and intensifies over parts of China and the Middle East. For North America, irrigation significantly increases precipitation under modern GHG forcing; this precipitation enhancement largely disappears under A1B forcing, reducing total latent heat fluxes and the overall irrigation cooling effect. Over India, irrigation rates are high enough to keep pace with increased evaporative demand from the increased GHG forcing and the magnitude of the cooling is maintained. Over China, GHG forcing reduces precipitation and shifts the region to a drier evaporative regime, leading to a relatively increased impact of additional water from irrigation on the surface energy balance. Irrigation enhances precipitation in the Middle East under increased GHG forcing, increasing total latent heat fluxes and enhancing the irrigation cooling effect. Ultimately, the extent to which irrigation will continue to compensate for the warming from increased GHG forcing will primarily depend on changes in the background evaporative regime, secondary irrigation effects (e.g. clouds, precipitation), and the ability of societies to maintain (or increase) current irrigation rates.

  19. Optimizing parameters of GTU cycle and design values of air-gas channel in a gas turbine with cooled nozzle and rotor blades

    Science.gov (United States)

    Kler, A. M.; Zakharov, Yu. B.

    2012-09-01

    The authors have formulated the problem of joint optimization of pressure and temperature of combustion products before gas turbine, profiles of nozzle and rotor blades of gas turbine, and cooling air flow rates through nozzle and rotor blades. The article offers an original approach to optimization of profiles of gas turbine blades where the optimized profiles are presented as linear combinations of preliminarily formed basic profiles. The given examples relate to optimization of the gas turbine unit on the criterion of power efficiency at preliminary heat removal from air flows supplied for the air-gas channel cooling and without such removal.

  20. Phase Diagram of Vertically Shaken Granular Matter

    CERN Document Server

    Eshuis, P; Lohse, D; Van der Meer, D; Van der Weele, K; Bos, Robert; Eshuis, Peter; Lohse, Detlef; Meer, Devaraj van der; Weele, Ko van der

    2006-01-01

    A shallow, vertically shaken granular bed in a quasi 2-D container is studied experimentally yielding a wider variety of phenomena than in any previous study: (1) bouncing bed, (2) undulations, (3) granular Leidenfrost effect, (4) convection rolls, and (5) granular gas. These phenomena and the transitions between them are characterized by dimensionless control parameters and combined in a full experimental phase diagram.

  1. Redistributing hot gas around galaxies: do cool clouds signal a solution to the overcooling problem?

    CERN Document Server

    Kaufmann, Tobias; Maller, Ariyeh H; Fang, Taotao; Wadsley, James

    2008-01-01

    We present a pair of high-resolution smoothed particle hydrodynamics (SPH) simulations that explore the evolution and cooling behavior of hot gas around Milky-Way size galaxies. The simulations contain the same total baryonic mass and are identical other than their initial gas density distributions. The first is initialised with a low entropy hot gas halo that traces the cuspy profile of the dark matter, and the second is initialised with a high-entropy hot halo with a cored density profile as might be expected in models with pre-heating feedback. Galaxy formation proceeds in dramatically different fashion depending on the initial setup. While the low-entropy halo cools rapidly, primarily from the central region, the high-entropy halo is quasi-stable for ~4 Gyr and eventually cools via the fragmentation and infall of clouds from ~100 kpc distances. The low-entropy halo's X-ray surface brightness is ~100 times brighter than current limits and the resultant disc galaxy contains more than half of the system's ba...

  2. Automatic heating and cooling system in a gas purge microsyringe extraction.

    Science.gov (United States)

    Piao, Xiangfan; Bi, Jinhu; Yang, Cui; Wang, Xiaoping; Wang, Juan; Li, Donghao

    2011-10-30

    The gas purge microsyringe extraction (GP-MSE) technique offers quantitative and simultaneous extraction, and rapid gas chromatographic-mass spectrometric determination of volatile and semivolatile chemicals is possible. To simplify the application, a new automatic temperature control system was developed here. Stable heating and cooling over a wide range of temperatures were achieved using a micro-heater and thermoelectric cooler under varying gas flow conditions. Temperatures could be accurately controlled in the range 20-350°C (heating) and 20 to -4°C (cooling). Temperature effects on the extraction performance of the GP-MSE were experimentally investigated by comparing the recoveries of polycyclic aromatic hydrocarbons (PAHs) under various experimental conditions. A sample treatment was completed within 3 min, which is much less than the time required for chromatographic analysis. The recovery of chemicals determined ranged from 81 to 96%. High reproducibility data (RSD ≤ 5%) were obtained for direct extraction of various analytes in spiked complex plant and biological samples. The data show that the heating and cooling system has potential applications in GP-MSE system for the direct determination of various kinds of volatile and semivolatile chemicals from complex matrices without any, or only minor, sample pretreatment.

  3. Pahs, Ionized Gas, and Molecular Hydrogen in Brightest Cluster Galaxies of Cool Core Clusters of Galaxies

    CERN Document Server

    Donahue, Megan; O'Connell, Robert W; Voit, G Mark; Hoffer, Aaron; McNamara, Brian R; Nulsen, Paul E J

    2011-01-01

    We present measurements of 5-25 {\\mu}m emission features of brightest cluster galaxies (BCGs) with strong optical emission lines in a sample of 9 cool-core clusters of galaxies observed with the Infrared Spectrograph on board the Spitzer Space Telescope. These systems provide a view of dusty molecular gas and star formation, surrounded by dense, X-ray emitting intracluster gas. Past work has shown that BCGs in cool-core clusters may host powerful radio sources, luminous optical emission line systems, and excess UV, while BCGs in other clusters never show this activity. In this sample, we detect polycyclic aromatic hydrocarbons (PAHs), extremely luminous, rotationally-excited molecular hydrogen line emission, forbidden line emission from ionized gas ([Ne II] and [Ne III]), and infrared continuum emission from warm dust and cool stars. We show here that these BCGs exhibit more luminous forbidden neon and H2 rotational line emission than star-forming galaxies with similar total infrared luminosities, as well as ...

  4. Stagnation region gas film cooling: Spanwise angled injection from multiple rows of holes. [gas turbine engines

    Science.gov (United States)

    Luckey, D. W.; Lecuyer, M. R.

    1981-01-01

    The stagnation region of a cylinder in a cross flow was used in experiments conducted with both a single row and multiple rows of spanwise angled (25 deg) coolant holes for a range of the coolant blowing ratio with a freestream to wall temperature ratio approximately equal to 1.7 and R(eD) = 90,000. Data from local heat flux measurements are presented for injection from a single row located at 5 deg, 22.9 deg, 40.8 deg, 58.7 deg from stagnation using a hole spacing ratio of S/d(o) = 5 and 10. Three multiple row configurations were also investigated. Data are presented for a uniform blowing distribution and for a nonuniform blowing distribution simulating a plenum supply. The data for local Stanton Number reduction demonstrated a lack of lateral spreading by the coolant jets. Heat flux levels larger than those without film cooling were observed directly behind the coolant holes as the blowing ratio exceeded a particular value. The data were spanwise averaged to illustrate the influence of injection location, blowing ratio and hole spacing. The large values of blowing ratio for the blowing distribution simulating a plenum supply resulted in heat flux levels behind the holes in excess of the values without film cooling. An increase in freestream turbulence intensity from 4.4 to 9.5 percent had a negligible effect on the film cooling performance.

  5. Gas turbine performance enhancement via utilizing different integrated turbine inlet cooling techniques

    Directory of Open Access Journals (Sweden)

    Alaa A. El-Shazly

    2016-09-01

    Full Text Available Regions that experience ambient temperatures rising during hot seasons have significant losses and impacts on both output power and efficiency of the gas turbine. When the ambient temperature increases, the air mass flow rate decreases, and hence leads to reduce the gas turbine produced power. Ambient air can be cooled by using either evaporative cooler or absorption chiller. Currently, the performance was simulated thermodynamically for a natural gas operated gas turbine. The performance was tested for the base case without any turbine inlet cooling (TIC systems and compared with the performance for both evaporative cooler and absorption chiller separately in terms of output power, thermal efficiency, heat rate, specific fuel consumption, consumed fuel mass flow rate, and economics. Results showed that at air ambient temperature equals to 37 °C and after deducting all the associated auxiliaries power consumption for both evaporative cooler and absorption chiller, the absorption chiller with regenerator can achieve an augmentation of 25.47% in power and 33.66% in efficiency which provides a saving in average power price about 13%, while the evaporative cooler provides only an increase of 5.56% in power and 1.55% in efficiency, and a saving of 3% in average power price.

  6. Gaussian kinetic model for granular gases.

    Science.gov (United States)

    Dufty, James W; Baskaran, Aparna; Zogaib, Lorena

    2004-05-01

    A kinetic model for the Boltzmann equation is proposed and explored as a practical means to investigate the properties of a dilute granular gas. It is shown that all spatially homogeneous initial distributions approach a universal "homogeneous cooling solution" after a few collisions. The homogeneous cooling solution (HCS) is studied in some detail and the exact solution is compared with known results for the hard sphere Boltzmann equation. It is shown that all qualitative features of the HCS, including the nature of overpopulation at large velocities, are reproduced by the kinetic model. It is also shown that all the transport coefficients are in excellent agreement with those from the Boltzmann equation. Also, the model is specialized to one having a velocity independent collision frequency and the resulting HCS and transport coefficients are compared to known results for the Maxwell model. The potential of the model for the study of more complex spatially inhomogeneous states is discussed.

  7. High-resolution mid-infrared spectroscopy of buffer-gas-cooled methyltrioxorhenium molecules

    CERN Document Server

    Tokunaga, Sean; Tarbutt, M; Darquié, B

    2016-01-01

    We demonstrate cryogenic buffer-gas cooling of gas-phase methyltrioxorhenium (MTO). This molecule is closely related to chiral organometallic molecules where the parity-violating energy differences between enantiomers may be measurable. The molecules are produced with a rotational temperature of approximately 6~K by laser ablation of an MTO pellet inside a cryogenic helium buffer gas cell. Facilitated by the low temperature, we demonstrate absorption spectroscopy of the 10.2~$\\mu$m antisymmetric Re=O stretching mode of MTO with a resolution of 8~MHz and a frequency accuracy of 30~MHz. We partially resolve the hyperfine structure and measure the nuclear quadrupole coupling of the excited vibrational state.

  8. Experimental and numerical investigation of heat transfer and pressure drop for innovative gas cooled systems

    Energy Technology Data Exchange (ETDEWEB)

    Gomez, R., E-mail: rodrigo.leija@kit.edu [Karlsruhe Institute of Technology, Institute for Neutron Physics and Reactor Technology, Hermann-von-Helmholtz No. 1, 76344 Eggenstein-Leopoldshafen (Germany); Buchholz, S. [Gesellschaft für Anlagen- und Reaktorsicherheit GRS mbH, Boltzmannstraße 2, 85748 Garching (Germany); Suikkanen, H. [Lappeenranta University of Technology, LUT Energy, PO Box 20, FI-53851 Lappeenranta (Finland)

    2015-08-15

    Highlights: • Experimental results of the L-STAR within the first stage of THINS project. • CFD validation for the heat transfer and pressure losses in innovative gas cooled systems. • The results indicate a strong dependency Turbulent Prandtl at the rod wall temperature distribution. • Gas loop facility suitable for the investigation of thermohydraulic issues of GFR, however there might be flow instabilities when flow is very low. - Abstract: Heat transfer enhancement through turbulence augmentation is recognized as a key factor for improving the safety and economic conditions in the development of both critical and subcritical innovative advanced gas cooled fast reactors (GFR) and transmutation systems. The L-STAR facility has been designed and erected at the Karlsruhe Institute of Technology (KIT) to study turbulent flow behavior and its heat transfer enhancement characteristics in gas cooled annular channels under a wide range of conditions. The test section consists of an annular hexagonal cross section channel with an inner electrical heater rod element, placed concentrically within the test section, which seeks to simulate the flow area of a fuel rod element in a GFR. The long term objective of the experimental study is to investigate and improve the understanding of complex turbulent convective enhancement mechanisms as well as the friction loss penalties of roughened fuel rods compared to smooth ones and to generate an accurate database for further development of physical models. In the first step, experimental results of the fluid flow with uniform heat release conditions for the smooth heater rod are presented. The pressure drops, as well as the axial temperature profiles along the heater rod surface have been measured at Reynolds numbers in the range from 4000 to 35,000. The experimental results of the first stage were compared with independently conducted CFD analyses performed at Lappeenranta University of Technology (LUT) with the code ANSYS

  9. Analysis of Precooling Injection Transient of Steam Generator for High Temperature Gas Cooled Reactor

    Directory of Open Access Journals (Sweden)

    Yan Wang

    2017-01-01

    Full Text Available After a postulated design basis accident leads high temperature gas cooled reactor to emergency shutdown, steam generator still remains with high temperature level and needs to be cooled down by a precooling before reactor restarts with clearing of fault. For the large difference of coolant temperature between inlet and outlet of steam generator in normal operation, the temperature distribution on the components of steam generator is very complicated. Therefore, the temperature descending rate of the components in steam generator needs to be limited to avoid the potential damage during the precooling stage. In this paper, a pebble-bed high temperature gas cooled reactor is modeled by thermal-hydraulic system analysis code and several postulated precooling injection transients are simulated and compared to evaluate their effects, which will provide support for the precooling design. The analysis results show that enough precooling injection is necessary to satisfy the precooling requirements, and larger mass flow rate of precooling water injection will accelerate the precooling process. The temperature decrease of steam generator is related to the precooling injection scenarios, and the maximal mass flow rate of the precooling injection should be limited to avoid the excessively quick temperature change of the structures in steam generator.

  10. Mesoscale Benchmark Demonstration Problem 1: Mesoscale Simulations of Intra-granular Fission Gas Bubbles in UO2 under Post-irradiation Thermal Annealing

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yulan; Hu, Shenyang Y.; Montgomery, Robert; Gao, Fei; Sun, Xin; Tonks, Michael; Biner, Bullent; Millet, Paul; Tikare, Veena; Radhakrishnan, Balasubramaniam; Andersson , David

    2012-04-11

    A study was conducted to evaluate the capabilities of different numerical methods used to represent microstructure behavior at the mesoscale for irradiated material using an idealized benchmark problem. The purpose of the mesoscale benchmark problem was to provide a common basis to assess several mesoscale methods with the objective of identifying the strengths and areas of improvement in the predictive modeling of microstructure evolution. In this work, mesoscale models (phase-field, Potts, and kinetic Monte Carlo) developed by PNNL, INL, SNL, and ORNL were used to calculate the evolution kinetics of intra-granular fission gas bubbles in UO2 fuel under post-irradiation thermal annealing conditions. The benchmark problem was constructed to include important microstructural evolution mechanisms on the kinetics of intra-granular fission gas bubble behavior such as the atomic diffusion of Xe atoms, U vacancies, and O vacancies, the effect of vacancy capture and emission from defects, and the elastic interaction of non-equilibrium gas bubbles. An idealized set of assumptions was imposed on the benchmark problem to simplify the mechanisms considered. The capability and numerical efficiency of different models are compared against selected experimental and simulation results. These comparisons find that the phase-field methods, by the nature of the free energy formulation, are able to represent a larger subset of the mechanisms influencing the intra-granular bubble growth and coarsening mechanisms in the idealized benchmark problem as compared to the Potts and kinetic Monte Carlo methods. It is recognized that the mesoscale benchmark problem as formulated does not specifically highlight the strengths of the discrete particle modeling used in the Potts and kinetic Monte Carlo methods. Future efforts are recommended to construct increasingly more complex mesoscale benchmark problems to further verify and validate the predictive capabilities of the mesoscale modeling

  11. EFFECTS OF COOLED EXTERNAL EXHAUST GAS RECIRCULATION ON DIESEL HOMOGENEOUS CHARGE COMPRESSION IGNITION ENGINE

    Institute of Scientific and Technical Information of China (English)

    SHI Lei; CUI Yi; DENG Kangyao

    2007-01-01

    The effects of cooled external exhaust gas recirculation (EGR) on the combustion and emission performance of diesel fuel homogeneous charge compression ignition (HCCI) are studied. Homogeneous mixture is formed by injecting fuel in-cylinder in the negative valve overlap (NVO) period. So, the HCCI combustion which has low NOx and smoke emission is achieved. Cooled external EGR can delay the start of combustion effectively, which is very useful for high cetane fuel (diesel) HCCI, because these fuels can easily self-ignition, which makes the start of combustion more early. External EGR can avoid the knock combustion of HCCI at high load which means that the EGR can expand the high load limit. HCCI maintains low smoke emission at various EGR rate and various load compared with conventional diesel engine because there is no fuel-rich area in cylinder.

  12. Evidence for a heated gas bubble inside the "cooling flow" region of MKW3s

    CERN Document Server

    Mazzotta, P; Paerels, F B S; Ferrigno, C; Colafrancesco, Sergio; Mewe, R; Forman, W R

    2002-01-01

    We report on the deep Chandra observation of central r=200kpc region of the cluster of galaxies MKW3s which was previously identified as a moderate cooling flow cluster. The Chandra image reveals two striking features -- a 100kpc long and 21kpc wide filament, extending from the center to the south-west and a nearly circular, 50kpc diameter depression 90 kpc south of the X-ray peak. The temperature map shows that the filamentary structure is colder while the surface brightness depression is hotter than the average cluster temperature at any radius. The hot and the cold regions indicate that both cooling and heating processes are taking place in the center of MKW3s. We argue that the surface brightness depression is produced by a heated, low-density gas bubble along the line of sight. We suggest that the heated bubble is produced by short-lived nuclear outbursts from the central galaxy.

  13. The absorption and emission spectrum of radiative cooling galactic fountain gas

    Science.gov (United States)

    Benjamin, Robert A.; Shapiro, Paul R.

    1993-01-01

    We have calculated the time-dependent, nonequilibrium thermal and ionization history of gas cooling radiatively from 10(exp 6) K in a one-dimensional, planar, steady-state flow model of the galactic fountain, including the effects of radiative transfer. Our previous optically thin calculations explored the effects of photoionization on such a flow and demonstrated that self-ionization was sufficient to cause the flow to match the observed galactic halo column densities of C 4, Si 4, and N 5 and UV emission from C 4 and O 3 in the constant density (isochoric) limit, which corresponded to cooling regions homogeneous on scales D less than or approximately equal to 1 kpc. Our new calculations which take full account of radiative transfer confirm the importance of self-ionization in enabling such a flow to match the data but allow a much larger range for cooling region sizes, i.e. D(sub 0) greater than or approximately equal to 15 pc. For an initial flow velocity v(sub 0) approximately equal to 100 km/s, comparable to the sound speed of a 10(exp 6) K gas, the initial density is found to be n(sub h,0) is approximately 2 x 10(exp -2) cm(exp -3), in reasonable agreement with other observation estimates, and D(sub 0) is approximately equal to 40 pc. We also compare predicted H(alpha) fluxes, UV line emission, and broadband x-ray fluxes with observed values. One dimensional numerical hydrodynamical calculations including the effects of radiative cooling are also presented.

  14. Characterization of a cryogenically cooled high-pressure gas jet for laser/cluster interaction experiments

    Science.gov (United States)

    Smith, R. A.; Ditmire, T.; Tisch, J. W. G.

    1998-11-01

    We have developed and carried out detailed characterization of a cryogenically cooled (34-300 K), high-pressure (55 kTorr) solenoid driven pulsed valve that has been used to produce dense jets of atomic clusters for high intensity laser interaction studies. Measurements including Rayleigh scattering and short pulse interferometry show that clusters of controlled size, from a few to >104 atoms/cluster can be produced from a broad range of light and heavy gases, at average atomic densities up to 4×1019 atoms/cc. Continuous temperature and pressure control of the valve allows us to vary mean cluster size while keeping the average atomic density constant, and we find that many aspects of the valves behavior are consistent with ideal gas laws. However, we also show that effects including the build up of flow on milliseconds time scales, the cooling of gas flowing into the valve, and condensation of gas inside the valve body at temperatures well above the liquefaction point need to be carefully characterized in order to decouple the operation of the jet from the laser interaction physics.

  15. Development status and operational features of the high temperature gas-cooled reactor. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Winkleblack, R.K.

    1976-04-01

    The objective of this study is to investigate the maturity of HTR-technology and to look out for possible technical problems, concerning introduction of large HTR power plants into the market. Further state and problems of introducing and closing the thorium fuel cycle is presented and judged. Finally, the state of development of advanced HTR-concepts for electricity production, the direct cycle HTR with helium turbine, and the gas-cooled fast breeder is discussed. In preparing the study, both HTR concepts with spherical and block-type fuel elements have been considered.

  16. Evaporative cooling of microscopic water droplets in vacuo: Molecular dynamics simulations and kinetic gas theory.

    Science.gov (United States)

    Schlesinger, Daniel; Sellberg, Jonas A; Nilsson, Anders; Pettersson, Lars G M

    2016-03-28

    In the present study, we investigate the process of evaporative cooling of nanometer-sized droplets in vacuum using molecular dynamics simulations with the TIP4P/2005 water model. The results are compared to the temperature evolution calculated from the Knudsen theory of evaporation which is derived from kinetic gas theory. The calculated and simulation results are found to be in very good agreement for an evaporation coefficient equal to unity. Our results are of interest to experiments utilizing droplet dispensers as well as to cloud micro-physics.

  17. High Sensitivity 1-D and 2-D Microwave Spectroscopy via Cryogenic Buffer Gas Cooling

    Science.gov (United States)

    Patterson, David; Eibenberger, Sandra

    2017-06-01

    All rotationally resolved spectroscopic methods rely on sources of cold molecules. For the last three decades, the workhorse technique for producing highly supersaturated samples of cold molecules has been the pulsed supersonic jet. We present here progress on our alternative method, cryogenic buffer gas cooling. Our high density, continuous source, and low noise temperature allow us to record microwave spectra at unprecedented sensitivity, with a dynamic range in excess of 10^6 achievable in a few minutes of integration time. This high sensitivity enables new protocols in both 1-D and 2-D microwave spectroscopy, including sensitive chiral analysis via nonlinear three wave mixing and applications as an analytical chemistry tool

  18. Efficiency of gas cooling and accretion at the disc-corona interface

    CERN Document Server

    Armillotta, L; Marinacci, F

    2016-01-01

    In star-forming galaxies, stellar feedback can have a dual effect on the circumgalactic medium both suppressing and stimulating gas accretion. The trigger of gas accretion can be caused by disc material ejected into the halo in the form of fountain clouds and by its interaction with the surrounding hot corona. Indeed, at the disc-corona interface, the mixing between the cold/metal-rich disc gas (T ~ 10^6 K) can dramatically reduce the cooling time of a portion of the corona and produce its condensation and accretion. We studied the interaction between fountain clouds and corona in different galactic environments through parsec-scale hydrodynamical simulations, including the presence of thermal conduction, a key mechanism that influences gas condensation. Our simulations showed that the coronal gas condensation strongly depends on the galactic environment, in particular it is less efficient for increasing virial temperature/mass of the haloes where galaxies reside and it is fully ineffective for objects with v...

  19. Enormous disc of cool gas surrounding the nearby powerful radio galaxy NGC 612 (PKS 0131-36)

    NARCIS (Netherlands)

    Emonts, B. H. C.; Morganti, R.; Oosterloo, T. A.; Holt, J.; Tadhunter, C. N.; van der Hulst, J. M.; Ojha, R.; Sadler, E. M.

    2008-01-01

    We present the detection of an enormous disc of cool neutral hydrogen (HI) gas surrounding the S0 galaxy NGC612, which hosts one of the nearest powerful radio sources (PKS 0131-36). Using the Australia Telescope Compact Array, we detect MHI = 1.8 x 10(9) M(circle dot) of HI emission-line gas that is

  20. Enormous disc of cool gas surrounding the nearby powerful radio galaxy NGC 612 (PKS 0131-36)

    NARCIS (Netherlands)

    Emonts, B. H. C.; Morganti, R.; Oosterloo, T. A.; Holt, J.; Tadhunter, C. N.; van der Hulst, J. M.; Ojha, R.; Sadler, E. M.

    2008-01-01

    We present the detection of an enormous disc of cool neutral hydrogen (HI) gas surrounding the S0 galaxy NGC612, which hosts one of the nearest powerful radio sources (PKS 0131-36). Using the Australia Telescope Compact Array, we detect MHI = 1.8 x 10(9) M(circle dot) of HI emission-line gas that is

  1. Gas cooling in semi-analytic models and SPH simulations: are results consistent?

    CERN Document Server

    Saro, A; Borgani, S; Dolag, K

    2010-01-01

    We present a detailed comparison between the galaxy populations within a massive cluster, as predicted by hydrodynamical SPH simulations and by a semi-analytic model (SAM) of galaxy formation. Both models include gas cooling and a simple prescription of star formation, which consists in transforming instantaneously any cold gas available into stars, while neglecting any source of energy feedback. We find that, in general, galaxy populations from SAMs and SPH have similar statistical properties, in agreement with previous studies. However, when comparing galaxies on an object-by-object basis, we find a number of interesting differences: a) the star formation histories of the brightest cluster galaxies (BCGs) from SAM and SPH models differ significantly, with the SPH BCG exhibiting a lower level of star formation activity at low redshift, and a more intense and shorter initial burst of star formation with respect to its SAM counterpart; b) while all stars associated with the BCG were formed in its progenitors i...

  2. Porous nuclear fuel element for high-temperature gas-cooled nuclear reactors

    Science.gov (United States)

    Youchison, Dennis L.; Williams, Brian E.; Benander, Robert E.

    2011-03-01

    Porous nuclear fuel elements for use in advanced high temperature gas-cooled nuclear reactors (HTGR's), and to processes for fabricating them. Advanced uranium bi-carbide, uranium tri-carbide and uranium carbonitride nuclear fuels can be used. These fuels have high melting temperatures, high thermal conductivity, and high resistance to erosion by hot hydrogen gas. Tri-carbide fuels, such as (U,Zr,Nb)C, can be fabricated using chemical vapor infiltration (CVI) to simultaneously deposit each of the three separate carbides, e.g., UC, ZrC, and NbC in a single CVI step. By using CVI, the nuclear fuel may be deposited inside of a highly porous skeletal structure made of, for example, reticulated vitreous carbon foam.

  3. Porous nuclear fuel element with internal skeleton for high-temperature gas-cooled nuclear reactors

    Science.gov (United States)

    Youchison, Dennis L.; Williams, Brian E.; Benander, Robert E.

    2013-09-03

    Porous nuclear fuel elements for use in advanced high temperature gas-cooled nuclear reactors (HTGR's), and to processes for fabricating them. Advanced uranium bi-carbide, uranium tri-carbide and uranium carbonitride nuclear fuels can be used. These fuels have high melting temperatures, high thermal conductivity, and high resistance to erosion by hot hydrogen gas. Tri-carbide fuels, such as (U,Zr,Nb)C, can be fabricated using chemical vapor infiltration (CVI) to simultaneously deposit each of the three separate carbides, e.g., UC, ZrC, and NbC in a single CVI step. By using CVI, the nuclear fuel may be deposited inside of a highly porous skeletal structure made of, for example, reticulated vitreous carbon foam.

  4. Sensitivity and resolution in frequency comb spectroscopy of buffer gas cooled polyatomic molecules

    Science.gov (United States)

    Changala, P. Bryan; Spaun, Ben; Patterson, David; Doyle, John M.; Ye, Jun

    2016-12-01

    We discuss the use of cavity-enhanced direct frequency comb spectroscopy in the mid-infrared region with buffer gas cooling of polyatomic molecules for high-precision rovibrational absorption spectroscopy. A frequency comb coupled to an optical enhancement cavity allows us to collect high-resolution, broad-bandwidth infrared spectra of translationally and rotationally cold (10-20 K) gas-phase molecules with high absorption sensitivity and fast acquisition times. The design and performance of the combined apparatus are discussed in detail. Recorded rovibrational spectra in the CH stretching region of several organic molecules, including vinyl bromide (CH_2CHBr), adamantane (C_{10}H_{16}), and diamantane (C_{14}H_{20}) demonstrate the resolution and sensitivity of this technique, as well as the intrinsic challenges faced in extending the frontier of high-resolution spectroscopy to large complex molecules.

  5. A small high temperature gas cooled reactor for nuclear marine propulsion

    Energy Technology Data Exchange (ETDEWEB)

    Brugiere, F.; Sillon, C. [Ecole des Applications Militaires de l' Energie Atomique, 50 - Cherbourg (France); Foster, A.; Hamilton, P.; Jewer, S.; Thompson, A.C. [Defence College of Electromechanical Engineering, Nuclear Dept., Military Rd, Gosport (United Kingdom); Kingston, T.; Williams, A.M.; Beeley, P.A. [Rolls-Royce (Marine Power), Raynesway, Derby (United Kingdom)

    2007-07-01

    Results from a design study for a hypothetical nuclear marine propulsion plant are presented. The plant utilizes a small High Temperature Gas Cooled Reactor (HTGCR) similar to the GTHTR300 design by the Japan Atomic Energy Agency with power being generated by a direct cycle gas turbine. The GTHTR300 design is modified in order to achieve the required power of 80 MWth and core lifetime of approximately 10 years. Thermal hydraulic analysis shows that in the event of a complete loss of flow accident the hot channel fuel temperature exceeds the 1600 Celsius degrees limit due to the high power peaking in assemblies adjacent to the inner reflector. Reactor dynamics shows oscillatory behaviour in rapid power transients. An automatic control rod system is suggested to overcome this problem. (authors)

  6. Solar heating, cooling and domestic hot water system installed at Columbia Gas System Service Corp. , Columbus, Ohio. Final report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-11-01

    The Solar Energy System located at the Columbia Gas Corporation, Columbus, Ohio, has 2978 ft/sup 2/ of Honeywell single axis tracking, concentrating collectors and provides solar energy for space heating, space cooling and domestic hot water. A 1,200,000 Btu/h Bryan water-tube gas boiler provides hot water for space heating. Space cooling is provided by a 100 ton Arkla hot water fired absorption chiller. Domestic hot water heating is provided by a 50 gallon natural gas domestic storage water heater. Extracts are included from the site files, specification references, drawings, installation, operation and maintenance instructions.

  7. Dark matter merging induced turbulence as an efficient engine for gas cooling

    Science.gov (United States)

    Prieto, Joaquin; Jimenez, Raul; Martí, Jose

    2012-02-01

    We have performed a cosmological numerical simulation of primordial baryonic gas collapsing on to a 3 × 107 M⊙ dark matter (DM) halo. We show that the large scale baryonic accretion process and the merger of few ˜ 106 M⊙ DM haloes, triggered by the gravitational potential of the biggest halo, are enough to create supersonic (?) shocks and develop a turbulent environment. In this scenario, the post-shocked regions are able to produce both H2 and deuterated H2 molecules very efficiently, reaching maximum abundances of ? and nHD˜ few × 10-6 nH, enough to cool the gas below 100 K in some regions. The kinetic energy spectrum of the turbulent primordial gas is close to a Burgers spectrum, ?, which could favour the formation of low-mass primordial stars. The solenoidal-to-total kinetic energy ratio is 0.65 ≲Rk≲ 0.7 for a wide range of wavenumbers; this value is close to the Rk≈ 2/3 natural equipartition energy value of a random turbulent flow. In this way, turbulence and molecular cooling seem to work together in order to produce potential star formation regions of cold dense gas in primordial environments. We conclude that both the mergers and the collapse process on to the main DM halo provide enough energy to develop supersonic turbulence which favours the molecular coolant formation: this mechanism, which could be universal and the main route towards the formation of the first galaxies, is able to create potential star-forming regions at high redshift.

  8. Simulation and control of water-gas shift packed bed reactor with inter-stage cooling

    Science.gov (United States)

    Saw, S. Z.; Nandong, J.

    2016-03-01

    Water-Gas Shift Reaction (WGSR) has become one of the well-known pathways for H2 production in industries. The issue with WGSR is that it is kinetically favored at high temperatures but thermodynamically favored at low temperatures, thus requiring careful consideration in the control design in order to ensure that the temperature used does not deactivate the catalyst. This paper studies the effect of a reactor arrangement with an inter-stage cooling implemented in the packed bed reactor to look at its effect on outlet temperature. A mathematical model is developed based on one-dimensional heat and mass transfers which incorporate the intra-particle effects. It is shown that the placement of the inter-stage cooling and the outlet temperature exiting the inter-stage cooling have strong influence on the reaction conversion. Several control strategies are explored for the process. It is shown that a feedback- feedforward control strategy using Multi-scale Control (MSC) is effective to regulate the reactor temperature profile which is critical to maintaining the catalysts activity.

  9. Surpassing the mass restriction of buffer gas cooling: Cooling of low mass ions by localized heavier atoms

    Science.gov (United States)

    Dutta, Sourav; Sawant, Rahul; Rangwala, S. A.

    2016-05-01

    Cooling of trapped ions has resulted in fascinating science including the realization of some of the most accurate atomic clocks. It has also found widespread application, for example, in mass spectrometry and cold chemistry. Among the different methods for cooling ions, cooling by elastic collisions with ultracold neutral atoms is arguably the most generic. However, in spite of its widespread application, there is confusion with regards the collisional heating/cooling of light ions by heavier neutral atoms. We address the question experimentally and demonstrate, for the first time, cooling of light ions by co-trapped heavy atoms. We show that trapped 39 K+ ions are cooled by localized ultracold neutral 85 Rb atoms. The atom-ion mass ratio (= 2.18) is well beyond any theoretical predictions so far. We further argue that cooling of ions by localized cold atoms is possible for any mass ratio. The result opens up the possibility of reaching the elusive s-wave collision regime in atom-ion collisions. S.D. is supported by DST-INSPIRE Faculty Fellowship, India.

  10. Test case specifications for coupled neutronics-thermal hydraulics calculation of Gas-cooled Fast Reactor

    Science.gov (United States)

    Osuský, F.; Bahdanovich, R.; Farkas, G.; Haščík, J.; Tikhomirov, G. V.

    2017-01-01

    The paper is focused on development of the coupled neutronics-thermal hydraulics model for the Gas-cooled Fast Reactor. It is necessary to carefully investigate coupled calculations of new concepts to avoid recriticality scenarios, as it is not possible to ensure sub-critical state for a fast reactor core under core disruptive accident conditions. Above mentioned calculations are also very suitable for development of new passive or inherent safety systems that can mitigate the occurrence of the recriticality scenarios. In the paper, the most promising fuel material compositions together with a geometry model are described for the Gas-cooled fast reactor. Seven fuel pin and fuel assembly geometry is proposed as a test case for coupled calculation with three different enrichments of fissile material in the form of Pu-UC. The reflective boundary condition is used in radial directions of the test case and vacuum boundary condition is used in axial directions. During these condition, the nuclear system is in super-critical state and to achieve a stable state (which is numerical representation of operational conditions) it is necessary to decrease the reactivity of the system. The iteration scheme is proposed, where SCALE code system is used for collapsing of a macroscopic cross-section into few group representation as input for coupled code NESTLE.

  11. Combined cooling and heating using a gas engine in a supermarket

    Energy Technology Data Exchange (ETDEWEB)

    Maidment, G.G. [South Bank Univ., London (United Kingdom). School of Engineering Systems and Design; Zhao, X.; Riffat, S.B. [Nottingham Univ. (United Kingdom). School of the Built Environment

    2001-07-01

    This paper reports the results of an investigation into the practical and economic viability of an integrated combined heating and cooling system in a supermarket. This system consists of a direct-drive screw compressor, which is powered by a throttle controlled gas engine. The waste heat from the engine is used to provide hot water for space heating and for general usage within the catering and toilet facilities in the supermarket. In this paper, the working principle of the novel system is first described. This details how the gas engine system may be integrated into the typical supermarket. The paper then describes a model, which is used to simulate the energy consumption of the supermarket. This is used to calculate the energy consumed by the conventional system and that used by a number of alternative combined heating and cooling system configurations, which are also described. The additional capital cost of each configuration is estimated and this is used to calculate the payback period. The results show that a payback period of 4.2 years may be achieved with a system that uses approximately 500,000 kWh per annum less primary energy than a conventional system. Finally, comparison between this system and a traditional Combined Heat and Power (CHP) installation is given. (author)

  12. Concept of an inherently-safe high temperature gas-cooled reactor

    Energy Technology Data Exchange (ETDEWEB)

    Ohashi, Hirofumi; Sato, Hiroyuki; Tachibana, Yukio; Kunitomi, Kazuhiko; Ogawa, Masuro [Nuclear Hydrogen and Heat Application Research Center, Japan Atomic Energy Agency, Oarai-machi, Ibaraki-ken, 311-1394 (Japan)

    2012-06-06

    As the challenge to ensure no harmful release of radioactive materials at the accidents by deterministic approach instead to satisfy acceptance criteria or safety goal for risk by probabilistic approach, new concept of advanced reactor, an inherently-safe high temperature gas-cooled reactor, is proposed based on the experience of the operation of the actual High Temperature Gas-cooled Reactor (HTGR) in Japan, High Temperature Engineering Test Reactor (HTTR), and the design of the commercial plant (GTHTR300), utilizing the inherent safety features of the HTGR (i.e., safety features based on physical phenomena). The safety design philosophy of the inherently-safe HTGR for the safety analysis of the radiological consequences is determined as the confinement of radioactive materials is assured by only inherent safety features without engineered safety features, AC power or prompt actions by plant personnel if the design extension conditions occur. Inherent safety features to prevent the loss or degradation of the confinement function are identified. It is proposed not to apply the probabilistic approach for the evaluation of the radiological consequences of the accidents in the safety analysis because no inherent safety features fail for the mitigation of the consequences of the accidents. Consequently, there are no event sequences to harmful release of radioactive materials if the design extension conditions occur in the inherently-safe HTGR concept. The concept and future R and D items for the inherently-safe HTGR are described in this paper.

  13. Gas-Cooled Thorium Reactor with Fuel Block of the Unified Design

    Directory of Open Access Journals (Sweden)

    Igor Shamanin

    2015-01-01

    Full Text Available Scientific researches of new technological platform realization carried out in Russia are based on ideas of nuclear fuel breeding in closed fuel cycle and physical principles of fast neutron reactors. Innovative projects of low-power reactor systems correspond to the new technological platform. High-temperature gas-cooled thorium reactors with good transportability properties, small installation time, and operation without overloading for a long time are considered perspective. Such small modular reactor systems at good commercial, competitive level are capable of creating the basis of the regional power industry of the Russian Federation. The analysis of information about application of thorium as fuel in reactor systems and its perspective use is presented in the work. The results of the first stage of neutron-physical researches of a 3D model of the high-temperature gas-cooled thorium reactor based on the fuel block of the unified design are given. The calculation 3D model for the program code of MCU-5 series was developed. According to the comparison results of neutron-physical characteristics, several optimum reactor core compositions were chosen. The results of calculations of the reactivity margins, neutron flux distribution, and power density in the reactor core for the chosen core compositions are presented in the work.

  14. On the quasihydrostatic flows of radiatively cooling self-gravitating gas clouds

    Energy Technology Data Exchange (ETDEWEB)

    Meerson, B.; Megged, E. [Hebrew Univ. of Jerusalem (Israel). Racah Institute of Physics; Tajima, T. [Univ. of Texas, Austin, TX (United States)

    1995-03-01

    Two model problems are considered, illustrating the dynamics of quasihydrostatic flows of radiatively cooling, optically thin self-gravitating gas clouds. In the first problem, spherically symmetric flows in an unmagnetized plasma are considered. For a power-law dependence of the radiative loss function on the temperature, a one-parameter family of self-similar solutions is found. The authors concentrate on a constant-mass cloud, one of the cases, when the self-similarity indices are uniquely selected. In this case, the self-similar flow problem can be formally reduced to the classical Lane-Emden equation and therefore solved analytically. The cloud is shown to undergo radiative condensation, if the gas specific heat ratio {gamma} > 4/3. The condensation proceeds either gradually, or in the form of (quasihydrostatic) collapse. For {gamma} < 4/3, the cloud is shown to expand. The second problem addresses a magnetized plasma slab that undergoes quasihydrostatic radiative cooling and condensation. The problem is solved analytically, employing the Lagrangian mass coordinate.

  15. THATCH: A computer code for modelling thermal networks of high- temperature gas-cooled nuclear reactors

    Energy Technology Data Exchange (ETDEWEB)

    Kroeger, P.G.; Kennett, R.J.; Colman, J.; Ginsberg, T. (Brookhaven National Lab., Upton, NY (United States))

    1991-10-01

    This report documents the THATCH code, which can be used to model general thermal and flow networks of solids and coolant channels in two-dimensional r-z geometries. The main application of THATCH is to model reactor thermo-hydraulic transients in High-Temperature Gas-Cooled Reactors (HTGRs). The available modules simulate pressurized or depressurized core heatup transients, heat transfer to general exterior sinks or to specific passive Reactor Cavity Cooling Systems, which can be air or water-cooled. Graphite oxidation during air or water ingress can be modelled, including the effects of added combustion products to the gas flow and the additional chemical energy release. A point kinetics model is available for analyzing reactivity excursions; for instance due to water ingress, and also for hypothetical no-scram scenarios. For most HTGR transients, which generally range over hours, a user-selected nodalization of the core in r-z geometry is used. However, a separate model of heat transfer in the symmetry element of each fuel element is also available for very rapid transients. This model can be applied coupled to the traditional coarser r-z nodalization. This report described the mathematical models used in the code and the method of solution. It describes the code and its various sub-elements. Details of the input data and file usage, with file formats, is given for the code, as well as for several preprocessing and postprocessing options. The THATCH model of the currently applicable 350 MW{sub th} reactor is described. Input data for four sample cases are given with output available in fiche form. Installation requirements and code limitations, as well as the most common error indications are listed. 31 refs., 23 figs., 32 tabs.

  16. The Cool ISM in S0 Galaxies. I. A Survey of Molecular Gas

    CERN Document Server

    Welch, G A; Welch, Gary A.; Sage, Leslie J.

    2003-01-01

    Lenticular galaxies remain remarkably mysterious as a class. Observations to date have not led to any broad consensus about their origins, properties and evolution, though they are often thought to have formed in one big burst of star formation early in the history of the Universe, and to have evolved relatively passively since then. In that picture, current theory predicts that stellar evolution returns substantial quantities of gas to the interstellar medium; most is ejected from the galaxy, but significant amounts of cool gas might be retained. Past searches for that material, though, have provided unclear results. We present results from a survey of molecular gas in a volume-limited sample of field S0 galaxies, selected from the Nearby Galaxies Catalog. CO emission is detected from 78 percent of the sample galaxies. We find that the molecular gas is almost always located inside the central few kiloparses of a lenticular galaxy, meaning that in general it is more centrally concentrated than in spirals. We ...

  17. NOT DEAD YET: COOL CIRCUMGALACTIC GAS IN THE HALOS OF EARLY-TYPE GALAXIES

    Energy Technology Data Exchange (ETDEWEB)

    Thom, Christopher; Tumlinson, Jason; Sembach, Kenneth R. [Space Telescope Science Institute, 3700 San Martin Drive, Baltimore, MD 21218 (United States); Werk, Jessica K.; Xavier Prochaska, J. [UCO/Lick Observatory, University of California, Santa Cruz, CA 95064 (United States); Oppenheimer, Benjamin D. [Leiden Observatory, Leiden University, P.O. Box 9513, NL-2300 RA Leiden (Netherlands); Peeples, Molly S. [Department of Physics and Astronomy, University of California Los Angeles, Los Angeles, CA 90095 (United States); Tripp, Todd M.; Katz, Neal S. [Department of Astronomy, University of Massachusetts, Amherst, MA 01003-9305 (United States); O' Meara, John M. [Department of Chemistry and Physics, Saint Michael' s College, Colchester, VT 05439 (United States); Ford, Amanda Brady; Dave, Romeel [Steward Observatory, University of Arizona, 933 N. Cherry Avenue, Tucson, AZ 85721 (United States); Weinberg, David H. [Department of Astronomy, Ohio State University, 140 W. 18th Avenue, Columbus, OH 43210 (United States)

    2012-10-20

    We report new observations of circumgalactic gas in the halos of early-type galaxies (ETGs) obtained by the COS-Halos Survey with the Cosmic Origins Spectrograph on board the Hubble Space Telescope. We find that detections of H I surrounding ETGs are typically as common and strong as around star-forming galaxies, implying that the total mass of circumgalactic material is comparable in the two populations. For ETGs, the covering fraction for H I absorption above 10{sup 16} cm{sup -2} is {approx}40%-50% within {approx}150 kpc. Line widths and kinematics of the detected material show it to be cold (T {approx}< 10{sup 5} K) in comparison to the virial temperature of the host halos. The implied masses of cool, photoionized circumgalactic medium baryons may be up to 10{sup 9}-10{sup 11} M{sub Sun }. Contrary to some theoretical expectations, strong halo H I absorbers do not disappear as part of the quenching of star formation. Even passive galaxies retain significant reservoirs of halo baryons that could replenish the interstellar gas reservoir and eventually form stars. This halo gas may feed the diffuse and molecular gas that is frequently observed inside ETGs.

  18. Demonstration of Enabling Spar-Shell Cooling Technology in Gas Turbines

    Energy Technology Data Exchange (ETDEWEB)

    Downs, James [Florida Turbine Technologies Inc., Jupiter, FL (United States)

    2014-12-29

    In this Advanced Turbine Program-funded Phase III project, Florida Turbine Technologies, Inc. (FTT) has developed and tested, at a pre-commercial prototypescale, spar-shell turbine airfoils in a commercial gas turbine. The airfoil development is based upon FTT’s research and development to date in Phases I and II of Small Business Innovative Research (SBIR) grants. During this program, FTT has partnered with an Original Equipment Manufacturer (OEM), Siemens Energy, to produce sparshell turbine components for the first pre-commercial prototype test in an F-Class industrial gas turbine engine and has successfully completed validation testing. This project will further the commercialization of this new technology in F-frame and other highly cooled turbine airfoil applications. FTT, in cooperation with Siemens, intends to offer the spar-shell vane as a first-tier supplier for retrofit applications and new large frame industrial gas turbines. The market for the spar-shell vane for these machines is huge. According to Forecast International, 3,211 new gas turbines units (in the >50MW capacity size range) will be ordered in ten years from 2007 to 2016. FTT intends to enter the market in a low rate initial production. After one year of successful extended use, FTT will quickly ramp up production and sales, with a target to capture 1% of the market within the first year and 10% within 5 years (2020).

  19. Contributions to the neutronic analysis of a gas-cooled fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    Martin-del-Campo, Cecilia, E-mail: cecilia.martin.del.campo@gmail.com [Departamento de Sistemas Energeticos, Facultad de Ingenieria, Universidad Nacional Autonoma de Mexico, Paseo Cuauhnahuac 8532. Jiutepec, Morelos (Mexico); Reyes-Ramirez, Ricardo, E-mail: ricarera@yahoo.com.mx [Departamento de Sistemas Energeticos, Facultad de Ingenieria, Universidad Nacional Autonoma de Mexico, Paseo Cuauhnahuac 8532. Jiutepec, Morelos (Mexico); Francois, Juan-Luis, E-mail: juan.luis.francois@gmail.com [Departamento de Sistemas Energeticos, Facultad de Ingenieria, Universidad Nacional Autonoma de Mexico, Paseo Cuauhnahuac 8532. Jiutepec, Morelos (Mexico); Reinking-Cejudo, Arturo G., E-mail: reinking@servidor.unam.mx [Departamento de Sistemas Energeticos, Facultad de Ingenieria, Universidad Nacional Autonoma de Mexico, Paseo Cuauhnahuac 8532. Jiutepec, Morelos (Mexico)

    2011-06-15

    Highlights: > Differences on reactivity with MCNPX and TRIPOLI-4 are negligible. > Fuel lattice and core criticality calculations were done. > A higher Doppler coefficient than coolant density coefficient. > Zirconium carbide is a better reflector than silicon carbide. > Adequate active height, radial size and reflector thickness were obtained. - Abstract: In this work the Monte Carlo codes MCNPX and TRIPOLI-4 were used to perform the criticality calculations of the fuel assembly and the core configuration of a gas-cooled fast reactor (GFR) concept, currently in development. The objective is to make contributions to the neutronic analysis of a gas-cooled fast reactor. In this study the fuel assembly is based on a hexagonal lattice of fuel-pins. The materials used are uranium and plutonium carbide as fuel, silicon carbide as cladding, and helium gas as coolant. Criticality calculations were done for a fuel assembly where the axial reflector thickness was varied in order to find the optimal thickness. In order to determine the best material to be used as a reflector, in the reactor core with neutrons of high energy spectrum, criticality calculations were done for three reflector materials: zirconium carbide, silicon carbide and natural uranium. It was found that the zirconium carbide provides the best neutron reflection. Criticality calculations using different active heights were done to determine the optimal height, and the reflector thickness was adjusted. Core criticality calculations were performed with different radius sizes to determine the active radial dimension of the core. A negative temperature coefficient of reactivity was verified for the fuel. The effect on reactivity produced by changes in the coolant density was also evaluated. We present the main neutronic characteristics of a preliminary fuel and core designs for the GFR concept. ENDF-VI cross-sections libraries were used in both the MCNPX and TRIPOLI-4 codes, and we verified that the obtained

  20. Application of Gamma code coupled with turbomachinery models for high temperature gas-cooled reactors

    Energy Technology Data Exchange (ETDEWEB)

    Chang Oh

    2008-02-01

    The very high-temperature gas-cooled reactor (VHTR) is envisioned as a single- or dual-purpose reactor for electricity and hydrogen generation. The concept has average coolant temperatures above 9000C and operational fuel temperatures above 12500C. The concept provides the potential for increased energy conversion efficiency and for high-temperature process heat application in addition to power generation. While all the High Temperature Gas Cooled Reactor (HTGR) concepts have sufficiently high temperature to support process heat applications, such as coal gasification, desalination or cogenerative processes, the VHTR’s higher temperatures allow broader applications, including thermochemical hydrogen production. However, the very high temperatures of this reactor concept can be detrimental to safety if a loss-ofcoolant accident (LOCA) occurs. Following the loss of coolant through the break and coolant depressurization, air will enter the core through the break by molecular diffusion and ultimately by natural convection, leading to oxidation of the in-core graphite structure and fuel. The oxidation will accelerate heatup of the reactor core and the release of a toxic gas, CO, and fission products. Thus, without any effective countermeasures, a pipe break may lead to significant fuel damage and fission product release. Prior to the start of this Korean/United States collaboration, no computer codes were available that had been sufficiently developed and validated to reliably simulate a LOCA in the VHTR. Therefore, we have worked for the past three years on developing and validating advanced computational methods for simulating LOCAs in a VHTR. GAMMA code is being developed to implement turbomachinery models in the power conversion unit (PCU) and ultimately models associated with the hydrogen plant. Some preliminary results will be described in this paper.

  1. Increasing of the gas turbine efficiency by inlet air cooling; Aumento da eficiencia de turbinas a gas por resfriamento do ar de admissao

    Energy Technology Data Exchange (ETDEWEB)

    Campos, Flavio Barboza [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas]. E-mail: fcampos@cenpes.petrobras.com.br; Landa, Henrique Gerken de [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas. Pesquisa, Desenvolvimento e Engenharia de Gas e Energia]. E-mail: hlanda@cenpes.petrobras.com.br

    2002-07-01

    The performance of most of gas turbines are affected by the temperature and pressure environmental conditions. The turbine power and efficiency are reduced by either the increasing in the temperature ou reducing the environmental pressure. This paper analyses the turbine inlet air cooling as an alternative for increasing the turbine efficiency. The various cooling routes of the turbine inlet air, found in the literature examined are presented and discussed.

  2. Effects of cooling and internal wave motions on gas transfer coefficients in a boreal lake

    Directory of Open Access Journals (Sweden)

    Jouni J. Heiskanen

    2014-05-01

    Full Text Available Lakes and other inland waters contribute significantly to regional and global carbon budgets. Emissions from lakes are often computed as the product of a gas transfer coefficient, k 600 , and the difference in concentration across the diffusive boundary layer at the air–water interface. Eddy covariance (EC techniques are increasingly being used in lacustrine gas flux studies and tend to report higher values for derived k 600 than other approaches. Using results from an EC study of a small, boreal lake, we modelled k 600 using a boundary-layer approach that included wind shear and cooling. During stratification, fluxes estimated by EC occasionally were higher than those obtained by our models. The high fluxes co-occurred with winds strong enough to induce deflections of the thermocline. We attribute the higher measured fluxes to upwelling-induced spatial variability in surface concentrations of CO2 within the EC footprint. We modelled the increased gas concentrations due to the upwelling and corrected our k 600 values using these higher CO2 concentrations. This approach led to greater congruence between measured and modelled k values during the stratified period. k 600 has a well-resolved and ~cubic relationship with wind speed when the water column is unstratified and the dissolved gases well mixed. During stratification and using the corrected k 600 , the same pattern is evident at higher winds, but k 600 has a median value of ~7 cm h−1 when winds are less than 6 m s−1, similar to observations in recent oceanographic studies. Our models for k 600 provide estimates of gas evasion at least 200% higher than earlier wind-based models. Our improved k 600 estimates emphasize the need for integrating within lake physics into models of greenhouse gas evasion.

  3. Case study on natural gas application for district heating and cooling in Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Maues, Jair Arone [Pontificia Universidade Catolica do Rio de Janeiro (IE/PUC-Rio), Rio de Janeiro, RJ (Brazil). Inst. de Energia; Akiyama, Junichi [Mitsui Gas e Energia do Brasil Ltda., Rio de janeiro, RJ (Brazil)

    2012-07-01

    The distributed cogeneration applying natural gas consists in an excellent alternative to use this source, but it is limited by a compatible heat demand that must be found in its application. District heating and cooling solutions can overcome this hurdle, especially in Brazil, a tropical country, where new industrial and commercial enterprises usually install central air conditioning systems. By 2020 natural gas demand shall reach a value of more than 200 MM m{sup 3} per day, accordingly to the Brazilian Energy Research Office (EPE, 2011). An expressive part of it could be consumed in cogeneration systems like the one described in this paper. This project had a special taxes exception rule applied. The chilled water and heated thermal oil produced were not taxed at all. But these two DHC utilities could obtain a different treatment if someone considers this is a tricky way of power and heat trading, which should be taxed as electricity and natural gas normally are. A bolder legislation with respect to the export of energy surplus would facilitate the project and operation of this kind of system, because the basic premise would be to attend the thermal demand with the electrical power installed, maximizing the global efficiency of the installation. An average 8 GW of Brazilian power demand, with roughly 50 MMm{sup 3}/day of natural gas consumption, could be attended by distributed energy gas cogeneration enterprises. If this prediction were totally accomplished it would bring the Brazilian participation of distributed energy in total power generation to values close to 10% in 2020, value already reached in average by the world biggest electricity's consumer countries (WADE, 2006). This also would mean an equivalent investment economy of approximately 11,000 MW in transmission and distribution lines capacity (author)

  4. Dark matter merging induced turbulence as an efficient engine for gas cooling

    CERN Document Server

    Prieto, Joaquin; Martí, Jose

    2011-01-01

    We have performed a cosmological numerical simulation of primordial baryonic gas collapsing onto a $3\\times10^7$M$_{\\odot}$ dark matter (DM) halo. We show that the large scale baryonic accretion process and the merger of few $\\sim10^6$ M$_{\\odot}$ DM halos, triggered by the gravitational potential of the biggest halo, is enough to create super sonic ($\\mathcal{M}>10$) shocks and develop a turbulent environment. In this scenario the post shocked regions are able to produced both H$_2$ and HD molecules very efficiently reaching maximum abundances of $n_\\mathrm{H_2}\\sim10^{-2}n_\\mathrm{H}$ and $n_\\mathrm{HD}\\sim \\mathrm{few}\\times10^{-6}n_\\mathrm{H}$, enough to cool the gas below 100K in some regions. The kinetic energy spectrum of the turbulent primordial gas is close to a Burgers spectrum, $\\hat{E}_k\\propto k^{-2}$, and the solenoidal to total kinetic energy ratio is $0.65\\la R_k\\la0.7$ for a wide range of wave numbers; this value is close to $R_k\\approx 2/3$ natural equipartition energy value of a random turb...

  5. Analysis of the horizontal flow in the advanced gas-cooled reactor

    Energy Technology Data Exchange (ETDEWEB)

    Duan, Y. [Department of Mechanical Engineering, University of Sheffield, Sheffield S1 3JD (United Kingdom); He, S., E-mail: s.he@sheffield.ac.uk [Department of Mechanical Engineering, University of Sheffield, Sheffield S1 3JD (United Kingdom); Ganesan, P. [Department of Mechanical Engineering, University of Malaya, Kuala Lumpur 50603 (Malaysia); Gotts, J. [EDF Energy, Barnwood, Gloucester GL4 3RS (United Kingdom)

    2014-06-01

    Highlights: • CFD is used to assess the effect of horizontal flows in AGRs. • The horizontal flows can reduce the graphite brick temperature significantly. • Such effects are not taken into consideration in current engineering calculations. • There might be flow instabilities when the fuel channel flow is very low but horizontal flows reduce its possibility. - Abstract: The purpose of the paper is to report a computational investigation of horizontal flows in the UK advanced-gas-cooled reactor (AGR) by using computational fluid dynamics with ANSYS FLUENT. The study is relevant to practical issues encountered in some AGR stations currently in operation in the UK. It is carried out using a comparative approach based on the results of two contrasting models: one simulating the full effect of the cross flow, the other simulating the simplified approach currently employed by the industry which neglects the momentum of the horizontal cross flow. The study reveals that the horizontal cross flow plays a significant role in the cooling of the moderator brick, while the axial variation of the brick geometry also significantly changes the distribution of the temperature within the brick. It is also found that under some circumstances the so-called horizontal inter-brick leakage (HIBL) flow could influence the cooling performance in the narrow gaps, resulting in a local hot spot. Furthermore, there may be flow instabilities in the flows in AGR fuel channels due to the interactions between the flow in the main arrowhead flow passages and that in some narrow passages connected to it, but the influence on the brick temperature is negligible. Horizontal cross flow has an effect of reducing such instabilities.

  6. Solar heating, cooling and domestic hot water system installed at Columbia Gas System Service Corporation, Columbus, Ohio

    Science.gov (United States)

    1980-01-01

    The solar energy system installed in the building has 2,978 sq ft of single axis tracking, concentrating collectors and provides solar energy for space heating, space cooling and domestic hot water. A 1,200,000 Btu/hour water tube gas boiler provides hot water for space heating. Space cooling is provided by a 100 ton hot water fired absorption chiller. Domestic hot water heating is provided by a 50 gallon natural gas domestic storage water heater. Extracts from the site files, specification references, drawings, installation, operation and maintenance instructions are included.

  7. Review of ORNL-TSF shielding experiments for the gas-cooled Fast Breeder Reactor Program

    Energy Technology Data Exchange (ETDEWEB)

    Abbott, L.S.; Ingersoll, D.T.; Muckenthaler, F.J.; Slater, C.O.

    1982-01-01

    During the period between 1975 and 1980 a series of experiments was performed at the ORNL Tower Shielding Facility in support of the shield design for a 300-MW(e) Gas Cooled Fast Breeder Demonstration Plant. This report reviews the experiments and calculations, which included studies of: (1) neutron streaming in the helium coolant passageways in the GCFR core; (2) the effectiveness of the shield designed to protect the reactor grid plate from radiation damage; (3) the adequacy of the radial shield in protecting the PCRV (prestressed concrete reactor vessel) from radiation damage; (4) neutron streaming between abutting sections of the radial shield; and (5) the effectiveness of the exit shield in reducing the neutron fluxes in the upper plenum region of the reactor.

  8. 2400MWt GAS-COOLED FAST REACTOR DHR STUDIES STATUS UPDATE.

    Energy Technology Data Exchange (ETDEWEB)

    CHENG,L.Y.; LUDEWIG, H.

    2007-06-01

    A topical report on demonstrating the efficacy of a proposed hybrid active/passive combination approach to the decay heat removal for an advanced 2400MWt GEN-IV gas-cooled fast reactor was published in March 2006. The analysis was performed with the system code RELAP5-3D (version 2.4.1.1a) and the model included the full complement of the power conversion unit (PCU): heat exchange components (recuperator, precooler, intercooler) and rotating machines (turbine, compressor). A re-analysis of the success case in Ref is presented in this report. The case was redone to correct unexpected changes in core heat structure temperatures when the PCU model was first integrated with the reactor model as documented in Ref [1]. Additional information on the modeling of the power conversion unit and the layout of the heat exchange components is provided in Appendix A.

  9. High temperature gas-cooled reactor (HTGR) graphite pebble fuel: Review of technologies for reprocessing

    Energy Technology Data Exchange (ETDEWEB)

    Mcwilliams, A. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-09-08

    This report reviews literature on reprocessing high temperature gas-cooled reactor graphite fuel components. A basic review of the various fuel components used in the pebble bed type reactors is provided along with a survey of synthesis methods for the fabrication of the fuel components. Several disposal options are considered for the graphite pebble fuel elements including the storage of intact pebbles, volume reduction by separating the graphite from fuel kernels, and complete processing of the pebbles for waste storage. Existing methods for graphite removal are presented and generally consist of mechanical separation techniques such as crushing and grinding chemical techniques through the use of acid digestion and oxidation. Potential methods for reprocessing the graphite pebbles include improvements to existing methods and novel technologies that have not previously been investigated for nuclear graphite waste applications. The best overall method will be dependent on the desired final waste form and needs to factor in the technical efficiency, political concerns, cost, and implementation.

  10. Using Wireless Sensor Networks to Achieve Intelligent Monitoring for High-Temperature Gas-Cooled Reactor

    Directory of Open Access Journals (Sweden)

    Jianghai Li

    2017-01-01

    Full Text Available High-temperature gas-cooled reactors (HTGR can incorporate wireless sensor network (WSN technology to improve safety and economic competitiveness. WSN has great potential in monitoring the equipment and processes within nuclear power plants (NPPs. This technology not only reduces the cost of regular monitoring but also enables intelligent monitoring. In intelligent monitoring, large sets of heterogeneous data collected by the WSN can be used to optimize the operation and maintenance of the HTGR. In this paper, WSN-based intelligent monitoring schemes that are specific for applications of HTGR are proposed. Three major concerns regarding wireless technology in HTGR are addressed: wireless devices interference, cybersecurity of wireless networks, and wireless standards selected for wireless platform. To process nonlinear and non-Gaussian data obtained by WSN for fault diagnosis, novel algorithms combining Kernel Entropy Component Analysis (KECA and support vector machine (SVM are developed.

  11. Power flattening on modified CANDLE small long life gas-cooled fast reactor

    Science.gov (United States)

    Monado, Fiber; Su'ud, Zaki; Waris, Abdul; Basar, Khairul; Ariani, Menik; Sekimoto, Hiroshi

    2014-09-01

    Gas-cooled Fast Reactor (GFR) is one of the candidates of next generation Nuclear Power Plants (NPPs) that expected to be operated commercially after 2030. In this research conceptual design study of long life 350 MWt GFR with natural uranium metallic fuel as fuel cycle input has been performed. Modified CANDLE burn-up strategy with first and second regions located near the last region (type B) has been applied. This reactor can be operated for 10 years without refuelling and fuel shuffling. Power peaking reduction is conducted by arranging the core radial direction into three regions with respectively uses fuel volume fraction 62.5%, 64% and 67.5%. The average power density in the modified core is about 82 Watt/cc and the power peaking factor decreased from 4.03 to 3.43.

  12. NGNP: High Temperature Gas-Cooled Reactor Key Definitions, Plant Capabilities, and Assumptions

    Energy Technology Data Exchange (ETDEWEB)

    Phillip Mills

    2012-02-01

    This document is intended to provide a Next Generation Nuclear Plant (NGNP) Project tool in which to collect and identify key definitions, plant capabilities, and inputs and assumptions to be used in ongoing efforts related to the licensing and deployment of a high temperature gas-cooled reactor (HTGR). These definitions, capabilities, and assumptions are extracted from a number of sources, including NGNP Project documents such as licensing related white papers [References 1-11] and previously issued requirement documents [References 13-15]. Also included is information agreed upon by the NGNP Regulatory Affairs group's Licensing Working Group and Configuration Council. The NGNP Project approach to licensing an HTGR plant via a combined license (COL) is defined within the referenced white papers and reference [12], and is not duplicated here.

  13. Simultaneous approach for simulation of a high-temperature gas-cooled reactor

    Institute of Scientific and Technical Information of China (English)

    Yang CHEN; Jiang-hong YOU; Zhi-jiang SHAO; Ke-xin WANG; Ji-xin QIAN

    2011-01-01

    The simulation of a high-temperature gas-cooled reactor pebble-bed module (HTR-PM) plant is discussed.This lumped parameter model has the form of a set differential algebraic equations (DAEs) that include stiff equations to model point neutron kinetics.The nested approach is the most common method to solve DAE,but this approach is very expensive and time-consuming due to inner iterations.This paper deals with an alternative approach in which a simultaneous solution method is used.The DAEs are discretized over a time horizon using collocation on finite elements,and Radau collocation points are applied.The resulting nonlinear algebraic equations can be solved by existing solvers.The discrete algorithm is discussed in detail; both accuracy and stability issues are considered.Finally,the simulation results are presented to validate the efficiency and accuracy of the simultaneous approach that takes much less time than the nested one.

  14. Safety and licensing of MHTGR (Modular High Temperature Gas Cooled Reactor)

    Energy Technology Data Exchange (ETDEWEB)

    Silady, F.A.; Millunzi, A.C.; Kelley, A.P. Jr.; Cunliffe, J.

    1987-07-01

    The Modular High Temperature Gas Cooled Reactor (MHTGR) design meets stringent top-level regulatory and user safety requirements that require that the normal and off-normal operation of the plant not disturb the public's day-to-day activities. Quantitative, top-level regulatory criteria have been specified from US NRC and EPA sources to guide the design. The user/utility group has further specified that these criteria be met at the plant boundary. The focus of the safety approach has then been centered on retaining the radionuclide inventory within the fuel by removing core heat, controlling chemical attack, and by controlling heat generation. The MHTGR is shown to passively meet the stringent requirements with margin. No operator action is required and the plant is insensitive to operator error.

  15. Power flattening on modified CANDLE small long life gas-cooled fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    Monado, Fiber [Nuclear Physics and Biophysics Research Group, Dept. of Physics, Faculty of Mathematics and Natural Sciences, Bandung Institute of Technology, Bandung, Indonesia and Dept. of Physics, Faculty of Mathematics and Natural Sciences, Sriwijaya University (Indonesia); Su' ud, Zaki; Waris, Abdul; Basar, Khairul [Nuclear Physics and Biophysics Research Group, Dept. of Physics, Faculty of Mathematics and Natural Sciences, Bandung Institute of Technology, Bandung (Indonesia); Ariani, Menik [Dept. of Physics, Faculty of Mathematics and Natural Sciences, Sriwijaya University (Indonesia); Sekimoto, Hiroshi [CRINES, Tokyo Institute of Technology, O-okoyama, Meguro-ku, Tokyo 152-8550 (Japan)

    2014-09-30

    Gas-cooled Fast Reactor (GFR) is one of the candidates of next generation Nuclear Power Plants (NPPs) that expected to be operated commercially after 2030. In this research conceptual design study of long life 350 MWt GFR with natural uranium metallic fuel as fuel cycle input has been performed. Modified CANDLE burn-up strategy with first and second regions located near the last region (type B) has been applied. This reactor can be operated for 10 years without refuelling and fuel shuffling. Power peaking reduction is conducted by arranging the core radial direction into three regions with respectively uses fuel volume fraction 62.5%, 64% and 67.5%. The average power density in the modified core is about 82 Watt/cc and the power peaking factor decreased from 4.03 to 3.43.

  16. High Temperature Gas-Cooled Reactor Projected Markets and Preliminary Economics

    Energy Technology Data Exchange (ETDEWEB)

    Larry Demick

    2011-08-01

    This paper summarizes the potential market for process heat produced by a high temperature gas-cooled reactor (HTGR), the environmental benefits reduced CO2 emissions will have on these markets, and the typical economics of projects using these applications. It gives examples of HTGR technological applications to industrial processes in the typical co-generation supply of process heat and electricity, the conversion of coal to transportation fuels and chemical process feedstock, and the production of ammonia as a feedstock for the production of ammonia derivatives, including fertilizer. It also demonstrates how uncertainties in capital costs and financial factors affect the economics of HTGR technology by analyzing the use of HTGR technology in the application of HTGR and high temperature steam electrolysis processes to produce hydrogen.

  17. Gas-cooled thorium reactor with fuel block of the unified design

    Directory of Open Access Journals (Sweden)

    I.V. Shamanin

    2015-11-01

    Analysis of information materials pertaining to the use of thorium as fuel element in rector facilities of the new generation and of its future potential was performed in the present study. Results of the first phase of neutronics studies of 3D model of high-temperatures gas-cooled reactor facility on the basis of unified design of the fuel block are presented. Calculation 3D model was developed using the software code of the MCU-5 series. Several optimal configurations of the reactor core were selected according to the results of comparison of neutronics characteristics of the examined options for the purpose of development of small-size modular nuclear power installations with power up to 60MW. Results of calculations of reactivity margin of the reactor, neutron flux distribution and power density profiles are presented for the selected options of reactor core configuration.

  18. Gas-Cooled Fast Reactor: A Historical Overview and Future Outlook

    Directory of Open Access Journals (Sweden)

    W. F. G. van Rooijen

    2009-01-01

    Full Text Available A review is given of developments in the area of Gas-Cooled Fast Reactors (GCFR in the period from roughly 1960 until 1980. During that period, the GCFR concept was expected to increase the breeding gain, the thermal efficiency of a nuclear power plant, and alleviate some of the problems associated with liquid metal coolants. During this period, the GCFR concept was found to be more challenging than liquid-metal-cooled reactors, and none were ever constructed. In the second part of the paper, we provide an overview of the investigations on GCFR since the year 2000, when the Generation IV Initiative rekindled interest in this reactor type. The new GCFR concepts focus primarily on sustainable nuclear power, with very efficient resource use, minimum waste, and a very strong focus on (passive safety. An overview is presented of the main design characteristics of these Gen IV GCFRs, and a literature list is provided to guide the interested reader towards more detailed publications.

  19. An ytterbium quantum gas microscope with narrow-line laser cooling

    Science.gov (United States)

    Yamamoto, Ryuta; Kobayashi, Jun; Kato, Kohei; Kuno, Takuma; Sakura, Yuto; Takahashi, Yoshiro

    2016-05-01

    Single-site resolved imaging of alkali metal in a two-dimensional optical lattice (Quantum Gas Microscope, QGM) is realized and enables us to directly observe the in-trap atom distribution and study quantum dynamics with single-site resolution. It is important to extend the applicability of a QGM technique to two-electron atoms such as alkaline-earth metal and ytterbium (Yb) atoms because it opens up many unique possibilities for the quantum simulation and quantum information research. Differently from the first report on single-site resolved imaging of Yb atoms with a long lattice constant 544 nm and a short lifetime of 62 μs without cooling, we successfully realize the QGM of Yb atoms with a short lattice constant 266 nm, in which we achieve a high-resolution imaging with a low temperature of 7.4 μK and a long lifetime of 7 s by narrow-line laser cooling. The high detection fidelity of 87(2) % is achieved in our method. In addition, we are developing a different mode of QGM for Yb atoms.

  20. Current design efforts for the gas-cooled fast reactor (GFR)

    Energy Technology Data Exchange (ETDEWEB)

    Weaver, K.D. [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, Idaho 83415-3850 (United States)]. e-mail: Kevan.Weaver@inl.gov

    2005-07-01

    Current research and development on the Gas-Cooled Fast Reactor (GCFR) has focused on the design of safety systems that will remove the decay heat during accident conditions, ion irradiations of candidate ceramic materials, joining studies of oxide dispersion strengthened alloys; and within the Advanced Fuel Cycle Initiative (AFC I) the fabrication of carbide fuels and ceramic fuel matrix materials, development of non-halide precursor low density and high density ceramic coatings, and neutron irradiation of candidate ceramic fuel matrix and metallic materials. The vast majority of this work has focused on the reference design for the GCFR: a helium-cooled, direct Brayton cycle power conversion system that will operate with an outlet temperature of 850 C at 7 MPa. In addition to the work being performed in the United States, seven international partners under the Generation IV International Forum (GIF) have identified their interest in participating in research related to the development of the GCFR. These are EURATOM (European Commission), France, Japan, South Africa, South Korea, Switzerland, and the United Kingdom. Of these, EURATOM (including the United Kingdom), France, Japan, and Switzerland have active research activities with respect to the GCFR. The research includes GCFR design and safety, and fuels/in-core materials/fuel cycle projects. This paper outlines the current design status of the GCFR, and includes work done in the areas mentioned above. (Author)

  1. Depletion Analysis of Modular High Temperature Gas-cooled Reactor Loaded with LEU/Thorium Fuel

    Energy Technology Data Exchange (ETDEWEB)

    Sonat Sen; Gilles Youinou

    2013-02-01

    Thorium based fuel has been considered as an option to uranium-based fuel, based on considerations of resource utilization (Thorium is more widely available when compared to Uranium). The fertile isotope of Thorium (Th-232) can be converted to fissile isotope U-233 by neutron capture during the operation of a suitable nuclear reactor such as High Temperature Gas-cooled Reactor (HTGR). However, the fertile Thorium needs a fissile supporter to start and maintain the conversion process such as U-235 or Pu-239. This report presents the results of a study that analyzed the thorium utilization in a prismatic HTGR, namely Modular High Temperature Gas-Cooled Reactor (MHTGR) that was designed by General Atomics (GA). The collected for the modeling of this design come from Chapter 4 of MHTGR Preliminary Safety Information Document that GA sent to Department of Energy (DOE) on 1995. Both full core and unit cell models were used to perform this analysis using SCALE 6.1 and Serpent 1.1.18. Because of the long mean free paths (and migration lengths) of neutrons in HTRs, using a unit cell to represent a whole core can be non-trivial. The sizes of these cells were set to match the spectral index between unit cell and full core domains. It was found that for the purposes of this study an adjusted unit cell model is adequate. Discharge isotopics and one-group cross-sections were delivered to the transmutation analysis team. This report provides documentation for these calculations

  2. Use of Distribution Devices for Hydraulic Profiling of Coolant Flow in Core Gas-cooled Reactors

    Directory of Open Access Journals (Sweden)

    A. A. Satin

    2014-01-01

    Full Text Available In setting up a reactor plant for the transportation-power module of the megawatt class an important task is to optimize the path of flow, i.e. providing moderate hydraulic resistance, uniform distribution of the coolant. Significant contribution to the hydraulic losses makes one selected design of the coolant supplies. It is, in particular, hemispherical or semi-elliptical shape of the supply reservoir, which is selected to reduce its mass, resulting in the formation of torusshaped vortex in the inlet manifold, that leads to uneven coolant velocity at the inlet into the core, the flow pulsations, hydraulic losses.To control the flow redistribution in the core according to the level of energy are used the switchgear - deflectors installed in a hemispherical reservoir supplying coolant to the fuel elements (FE of the core of gas-cooled reactor. This design solution has an effect on the structure of the flow, rate in the cooling duct, and the flow resistance of the collector.In this paper we present the results of experiments carried out on the gas dynamic model of coolant paths, deflectors, and core, comprising 55 fuel rod simulators. Numerical simulation of flow in two-parameter model, using the k-ε turbulence model, and the software package ANSYS CFX v14.0 is performed. The paper demonstrates that experimental results are in compliance with calculated ones.The results obtained suggest that the use of switchgear ensures a coolant flow balance directly at the core inlet, thereby providing temperature reduction of fuel rods with a uniform power release in the cross-section. Considered options to find constructive solutions for deflectors give an idea to solve the problem of reducing hydraulic losses in the coolant paths, to decrease pulsation components of flow in the core and length of initial section of flow stabilization.

  3. Development of GAMMA Code and Evaluation for a Very High Temperature gas-Cooled Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Chang H; Lim, H.S.; Kim, E.S.; NO, H.C.

    2007-06-01

    The very high-temperature gas-cooled reactor (VHTR) is envisioned as a single- or dual-purpose reactor for electricity and hydrogen generation. The concept has average coolant temperatures above 9000C and operational fuel temperatures above 12500C. The concept provides the potential for increased energy conversion efficiency and for high-temperature process heat application in addition to power generation. While all the High Temperature Gas Cooled Reactor (HTGR) concepts have sufficiently high temperature to support process heat applications, such as coal gasification, desalination or cogenerative processes, the VHTR’s higher temperatures allow broader applications, including thermochemical hydrogen production. However, the very high temperatures of this reactor concept can be detrimental to safety if a loss-of-coolant accident (LOCA) occurs. Following the loss of coolant through the break and coolant depressurization, air will enter the core through the break by molecular diffusion and ultimately by natural convection, leading to oxidation of the in-core graphite structure and fuel. The oxidation will accelerate heatup of the reactor core and the release of toxic gasses (CO and CO2) and fission products. Thus, without any effective countermeasures, a pipe break may lead to significant fuel damage and fission product release. Prior to the start of this Korean/United States collaboration, no computer codes were available that had been sufficiently developed and validated to reliably simulate a LOCA in the VHTR. Therefore, we have worked for the past three years on developing and validating advanced computational methods for simulating LOCAs in a VHTR. This paper will also include what improvements will be made in the Gamma code for the VHTR.

  4. Decompaction and fluidization of a saturated and confined granular medium by injection of a viscous liquid or gas.

    Science.gov (United States)

    Johnsen, Ø; Chevalier, C; Lindner, A; Toussaint, R; Clément, E; Måløy, K J; Flekkøy, E G; Schmittbuhl, J

    2008-11-01

    We compare quantitatively two experimental situations concerning injection of a miscible fluid into an initially jammed granular medium saturated with the same fluid, confined in a Hele-Shaw cell. The two experiments are identical, apart from the interstitial and injected fluid, which is in one case air injected into a dry granular packing, and in the other case silicone oil injected into a dense suspension. In spite of the strong differences regarding the nature of the two fluids, strikingly similar dynamical and geometrical features are identified as functions of the control parameters: cell thickness and applied fluid injection pressure. In both cases an initial hydrodynamically driven decompaction process controls the unjamming and prepares the final displacement process characterized by fingerlike patterns empty of grains. The pattern shapes are comparable. In addition, the mobilities of the coupled fluid-grain flow, rescaled by the interstitial fluid viscosity and grain diameter squared, are of the same range and behave comparably. The mobility proves to depend on the initial solid fraction of the medium. Subtle differences are observed in geometrical aspects like the finger width with respect to the control parameters.

  5. Exergy, Economic and Environmental Analyses of Gas Turbine Inlet Air Cooling with a Heat Pump Using a Novel System Configuration

    Directory of Open Access Journals (Sweden)

    Mohammad Reza Majdi Yazdi

    2015-10-01

    Full Text Available Gas turbines incur a loss of output power during hot seasons due to high ambient air temperatures, and input air cooling systems are often used to partly offset this problem. Here, results are reported for an investigation of the utilization of a heat pump to cool the inlet air of a gas turbine compressor. The analyses are carried out for two climates: the city of Yazd, Iran, which has a hot, arid climate, and Tehran, Iran, which has a temperate climate. The heat pump input power is obtained from the gas turbine. The following parameters are determined, with and without the heat pump: net output power, first and second law efficiencies, quantities and costs of environmental pollutants, entropy generation and power generation. The results suggest that, by using the air-inlet cooling system, the mean output power increases during hot seasons by 11.5% and 10% for Yazd and Tehran, respectively, and that the costs of power generation (including pollution costs decrease by 11% and 10% for Yazd and Tehran, respectively. Also, the rate of generation of pollutants such as NOx and CO decrease by about 10% for Yazd and 35% for Tehran, while the average annual entropy generation rate increases by 9% for Yazd and 7% for Tehran, through air-inlet cooling. The average increase of the system first law efficiency is 2% and of the system second law efficiency is 1.5% with the inlet-air cooling system.

  6. Measurement of the orientation of buffer-gas-cooled, electrostatically-guided ammonia molecules

    Science.gov (United States)

    Steer, Edward W.; Petralia, Lorenzo S.; Western, Colin M.; Heazlewood, Brianna R.; Softley, Timothy P.

    2017-02-01

    The extent to which the spatial orientation of internally and translationally cold ammonia molecules can be controlled as molecules pass out of a quadrupole guide and through different electric field regions is examined. Ammonia molecules are collisionally cooled in a buffer gas cell, and are subsequently guided by a three-bend electrostatic quadrupole into a detection chamber. The orientation of ammonia molecules is probed using (2 + 1) resonance-enhanced multiphoton ionisation (REMPI), with the laser polarisation axis aligned both parallel and perpendicular to the time-of-flight axis. Even with the presence of a near-zero field region, the ammonia REMPI spectra indicate some retention of orientation. Monte Carlo simulations propagating the time-dependent Schrödinger equation in a full basis set including the hyperfine interaction enable the orientation of ammonia molecules to be calculated - with respect to both the local field direction and a space-fixed axis - as the molecules pass through different electric field regions. The simulations indicate that the orientation of ∼95% of ammonia molecules in JK =11 could be achieved with the application of a small bias voltage (17 V) to the mesh separating the quadrupole and detection regions. Following the recent combination of the buffer gas cell and quadrupole guide apparatus with a linear Paul ion trap, this result could enable one to examine the influence of molecular orientation on ion-molecule reaction dynamics and kinetics.

  7. Corrosion of high temperature alloys in the coolant helium of a gas cooled reactor

    Energy Technology Data Exchange (ETDEWEB)

    Cabet, C.; Terlain, A. [Service de la Corrosion et du Comportement des Materiaux dans leur Environnement, DEN/DPC - CEA/Saclay, Gif sur Yvette (France); Monnier, A. [Lab. de Genie Electrique de Paris, Plateau du Moulon, Gif sur Yvette (France)

    2004-07-01

    The corrosion of structural alloys in gas cooled reactor environment appears to be a critical issue. The coolant helium proved to contain impurities mainly H{sub 2}, H{sub 2}O, CO, and CH{sub 4} in the microbar range that interact with metallic materials at high temperature. Surface scale formation, bulk carburisation and/or decarburisation can occur, depending on the gas chemistry, the alloy composition and the temperature. These structural transformations can notably influence the component mechanical properties. A short review of the literature on the topic is first given. Corrosion tests with high chromium alloys and a Mo-based alloy were carried out at 750 C in a purposely-designed facility under simulated GCR helium. The first, rather short term, results showed that the Mo-based alloy was inert while the others alloys oxidised during at least 900 hours. The alloy with the higher Al and Ti contents exhibited poor oxidation resistance impeding its use as structural material without further investigations. (orig.)

  8. Not Dead Yet: Cool Circumgalactic Gas in the Halos of Early Type Galaxies

    CERN Document Server

    Thom, Christopher; Werk, Jessica K; Prochaska, J Xavier; Oppenheimer, Benjamin D; Peeples, Molly S; Tripp, Todd M; Katz, Neal S; O'Meara, John M; Ford, Amanda Brady; Dave, Romeel; Sembach, Kenneth R; Weinberg, David H

    2012-01-01

    We report new observations of circumgalactic gas in the halos of early type galaxies obtained by the COS-Halos Survey with the Cosmic Origins Spectrograph onboard the Hubble Space Telescope. We find that detections of HI surrounding early type galaxies are typically as common and strong as around star-forming galaxies, implying that the total mass of circumgalactic material is comparable in the two populations. For early type galaxies, the covering fraction for HI absorption above 10^16 cm^2 is ~40-50% within ~150 kpc. Line widths and kinematics of the detected material show it to be cold (T ~< 10^5 K) in comparison to the virial temperature of the host halos. The implied masses of cool, photoionized CGM baryons may be up to 10^9 --- 10^11 Msun. Contrary to some theoretical expectations, strong halo HI absorbers do not disappear as part of the quenching of star-formation. Even passive galaxies retain significant reservoirs of halo baryons which could replenish the interstellar gas reservoir and eventually ...

  9. Thermochemical Analysis of Gas-Cooled Reactor Fuels Containing Am and Pu Oxides

    Energy Technology Data Exchange (ETDEWEB)

    Lindemer, T.B.

    2002-09-05

    Literature values and estimated data for the thermodynamics of the actinide oxides and fission products are applied to explain the chemical behavior in gas-cooled-reactor fuels. Emphasis is placed on the Am-O-C and Pu-O-C systems and the data are used to plot the oxygen chemical potential versus temperature of solid-solid and solid-gas equilibria. These results help explain observations of vaporization in Am oxides, nitrides, and carbides and provide guidance for the ceramic processing of the fuels. The thermodynamic analysis is then extended to the fission product systems and the Si-C-O system. Existing data on oxygen release (primarily as CO) as a function of burnup in the thoria-urania fuel system is reviewed and compared to values calculated from thermodynamic data. The calculations of oxygen release are then extended to the plutonia and americia fuels. Use of ZrC not only as a particle coating that may be more resistant to corrosion by Pd and other noble-metal fission products, but also as a means to getter oxygen released by fission is discussed.

  10. Blue-sky bifurcation of ion energies and the limits of neutral-gas sympathetic cooling of trapped ions

    Science.gov (United States)

    Schowalter, Steven J.; Dunning, Alexander J.; Chen, Kuang; Puri, Prateek; Schneider, Christian; Hudson, Eric R.

    2016-08-01

    Sympathetic cooling of trapped ions through collisions with neutral buffer gases is critical to a variety of modern scientific fields, including fundamental chemistry, mass spectrometry, nuclear and particle physics, and atomic and molecular physics. Despite its widespread use over four decades, there remain open questions regarding its fundamental limitations. To probe these limits, here we examine the steady-state evolution of up to 10 barium ions immersed in a gas of three-million laser-cooled calcium atoms. We observe and explain the emergence of nonequilibrium behaviour as evidenced by bifurcations in the ion steady-state temperature, parameterized by ion number. We show that this behaviour leads to the limitations in creating and maintaining translationally cold samples of trapped ions using neutral-gas sympathetic cooling. These results may provide a route to studying non-equilibrium thermodynamics at the atomic level.

  11. Blue-sky bifurcation of ion energies and the limits of neutral-gas sympathetic cooling of trapped ions

    CERN Document Server

    Schowalter, Steven J; Chen, Kuang; Puri, Prateek; Schneider, Christian; Hudson, Eric R

    2016-01-01

    Sympathetic cooling of trapped ions through collisions with neutral buffer gases is critical to a variety of modern scientific fields, including fundamental chemistry, mass spectrometry, nuclear and particle physics, and atomic and molecular physics. Despite its widespread use over four decades, there remain open questions regarding its fundamental limitations. To probe these limits, here we examine the steady-state evolution of up to ten barium ions immersed in a gas of three-million laser-cooled calcium atoms. We observe and explain the emergence of nonequilibrium behavior as evidenced by bifurcations in the ion steady-state temperature, parameterized by ion number. We show that this behavior leads to limitations in creating and maintaining translationally cold samples of trapped ions using neutral-gas sympathetic cooling. These results may provide a route to studying nonequilibrium thermodynamics.

  12. Blue-sky bifurcation of ion energies and the limits of neutral-gas sympathetic cooling of trapped ions

    Science.gov (United States)

    Schowalter, Steven J.; Dunning, Alexander J.; Chen, Kuang; Puri, Prateek; Schneider, Christian; Hudson, Eric R.

    2016-01-01

    Sympathetic cooling of trapped ions through collisions with neutral buffer gases is critical to a variety of modern scientific fields, including fundamental chemistry, mass spectrometry, nuclear and particle physics, and atomic and molecular physics. Despite its widespread use over four decades, there remain open questions regarding its fundamental limitations. To probe these limits, here we examine the steady-state evolution of up to 10 barium ions immersed in a gas of three-million laser-cooled calcium atoms. We observe and explain the emergence of nonequilibrium behaviour as evidenced by bifurcations in the ion steady-state temperature, parameterized by ion number. We show that this behaviour leads to the limitations in creating and maintaining translationally cold samples of trapped ions using neutral-gas sympathetic cooling. These results may provide a route to studying non-equilibrium thermodynamics at the atomic level. PMID:27511602

  13. High-resolution optical spectroscopy with a buffer-gas-cooled beam of BaH molecules

    Science.gov (United States)

    Iwata, G. Z.; McNally, R. L.; Zelevinsky, T.

    2017-08-01

    Barium monohydride (BaH) is an attractive candidate for extending laser cooling and trapping techniques to diatomic hydrides. The apparatus and high-resolution optical spectroscopy presented here demonstrate progress toward this goal. A cryogenic buffer-gas-cooled molecular beam of BaH was constructed and characterized. Pulsed laser ablation into cryogenic helium buffer gas delivers ˜1 ×1010 molecules/sr/pulse in the X +2Σ (v''=0 ,N''=1 ) state of primary interest. More than 1 ×107 of these molecules per pulse enter the downstream science region with forward velocities below 100 m/s and transverse temperature of 0.1 K. This molecular beam enabled high-resolution optical spectra of BaH in quantum states relevant to laser slowing and cooling. The reported measurements include hyperfine structure and magnetic g factors in the X +2Σ , B +2Σ , and A 1/2 2Π states.

  14. Flow Integrating Section for a Gas Turbine Engine in Which Turbine Blades are Cooled by Full Compressor Flow

    Energy Technology Data Exchange (ETDEWEB)

    Steward, W. Gene

    1999-11-14

    Routing of full compressor flow through hollow turbine blades achieves unusually effective blade cooling and allows a significant increase in turbine inlet gas temperature and, hence, engine efficiency. The invention, ''flow integrating section'' alleviates the turbine dissipation of kinetic energy of air jets leaving the hollow blades as they enter the compressor diffuser.

  15. Nuclear Engineering Computer Modules, Thermal-Hydraulics, TH-3: High Temperature Gas Cooled Reactor Thermal-Hydraulics.

    Science.gov (United States)

    Reihman, Thomas C.

    This learning module is concerned with the temperature field, the heat transfer rates, and the coolant pressure drop in typical high temperature gas-cooled reactor (HTGR) fuel assemblies. As in all of the modules of this series, emphasis is placed on developing the theory and demonstrating its use with a simplified model. The heart of the module…

  16. Dynamical cooling of galactic discs by molecular cloud collisions - origin of giant clumps in gas-rich galaxy discs

    Science.gov (United States)

    Li, Guang-Xing

    2017-10-01

    Different from Milky Way-like galaxies, discs of gas-rich galaxies are clumpy. It is believed that the clumps form because of gravitational instability. However, a necessary condition for gravitational instability to develop is that the disc must dissipate its kinetic energy effectively, this energy dissipation (also called cooling) is not well understood. We propose that collisions (coagulation) between molecular clouds dissipate the kinetic energy of the discs, which leads to a dynamical cooling. The effectiveness of this dynamical cooling is quantified by the dissipation parameter D, which is the ratio between the free-fall time t_ff≈ 1/ √{G ρ _{disc}} and the cooling time determined by the cloud collision process tcool. This ratio is related to the ratio between the mean surface density of the disc Σdisc and the mean surface density of molecular clouds in the disc Σcloud. When D cloud), cloud collision cooling is inefficient, and fragmentation is suppressed. When D > 1/3 (which roughly corresponds to Σdisc > 1/3Σcloud), cloud-cloud collisions lead to a rapid cooling through which clumps form. On smaller scales, cloud-cloud collisions can drive molecular cloud turbulence. This dynamical cooling process can be taken into account in numerical simulations as a sub-grid model to simulate the global evolution of disc galaxies.

  17. Unified rheology of vibro-fluidized dry granular media: From slow dense flows to fast gas-like regimes

    Science.gov (United States)

    Gnoli, Andrea; Lasanta, Antonio; Sarracino, Alessandro; Puglisi, Andrea

    2016-01-01

    Granular media take on great importance in industry and geophysics, posing a severe challenge to materials science. Their response properties elude known soft rheological models, even when the yield-stress discontinuity is blurred by vibro-fluidization. Here we propose a broad rheological scenario where average stress sums up a frictional contribution, generalizing conventional μ(I)-rheology, and a kinetic collisional term dominating at fast fluidization. Our conjecture fairly describes a wide series of experiments in a vibrofluidized vane setup, whose phenomenology includes velocity weakening, shear thinning, a discontinuous thinning transition, and gaseous shear thickening. The employed setup gives access to dynamic fluctuations, which exhibit a broad range of timescales. In the slow dense regime the frequency of cage-opening increases with stress and enhances, with respect to μ(I)-rheology, the decrease of viscosity. Diffusivity is exponential in the shear stress in both thinning and thickening regimes, with a huge growth near the transition. PMID:27924928

  18. Screening of Gas-Cooled Reactor Thermal-Hydraulic and Safety Analysis Tools and Experimental Database

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Won Jae; Kim, Min Hwan; Lee, Seung Wook (and others)

    2007-08-15

    This report is a final report of I-NERI Project, 'Screening of Gas-cooled Reactor Thermal Hydraulic and Safety Analysis Tools and Experimental Database 'jointly carried out by KAERI, ANL and INL. In this study, we developed the basic technologies required to develop and validate the VHTR TH/safety analysis tools and evaluated the TH/safety database information. The research tasks consist of; 1) code qualification methodology (INL), 2) high-level PIRTs for major nucleus set of events (KAERI, ANL, INL), 3) initial scaling and scoping analysis (ANL, KAERI, INL), 4) filtering of TH/safety tools (KAERI, INL), 5) evaluation of TH/safety database information (KAERI, INL, ANL) and 6) key scoping analysis (KAERI). The code qualification methodology identifies the role of PIRTs in the R and D process and the bottom-up and top-down code validation methods. Since the design of VHTR is still evolving, we generated the high-level PIRTs referencing 600MWth block-type GT-MHR and 400MWth pebble-type PBMR. Nucleus set of events that represents the VHTR safety and operational transients consists of the enveloping scenarios of HPCC (high pressure conduction cooling: loss of primary flow), LPCC/Air-Ingress (low pressure conduction cooling: loss of coolant), LC (load changes: power maneuvering), ATWS (anticipated transients without scram: reactivity insertion), WS (water ingress: water-interfacing system break) and HU (hydrogen-side upset: loss of heat sink). The initial scaling analysis defines dimensionless parameters that need to be reflected in mixed convection modeling and the initial scoping analysis provided the reference system transients used in the PIRTs generation. For the PIRTs phenomena, we evaluated the modeling capability of the candidate TH/safety tools and derived a model improvement need. By surveying and evaluating the TH/safety database information, a tools V and V matrix has been developed. Through the key scoping analysis using available database, the

  19. Method and apparatus maintaining multi-component sample gas constituents in vapor phase during sample extraction and cooling

    Energy Technology Data Exchange (ETDEWEB)

    Farthing, William Earl (Pinson, AL); Felix, Larry Gordon (Pelham, AL); Snyder, Todd Robert (Birmingham, AL)

    2009-12-15

    An apparatus and method for diluting and cooling that is extracted from high temperature and/or high pressure industrial processes. Through a feedback process, a specialized, CFD-modeled dilution cooler is employed along with real-time estimations of the point at which condensation will occur within the dilution cooler to define a level of dilution and diluted gas temperature that results in a gas that can be conveyed to standard gas analyzers that contains no condensed hydrocarbon compounds or condensed moisture.

  20. Cold molecular gas in the Perseus cluster core - Association with X-ray cavity, Halpha filaments and cooling flow -

    CERN Document Server

    Salomé, P; Crawford, C; Edge, A C; Erlund, M; Fabian, A C; Hatch, N A; Johnstone, R M; Sanders, J S; Wilman, R J

    2006-01-01

    Cold molecular gas has been recently detected in several cooling flow clusters of galaxies where huge optical nebulosities often stand. These optical filaments are tightly linked to the cooling flow and to the related phenomena, like the rising bubbles of relativistic plasma, fed by the radio jets. We present here a map in the CO(2-1) rotational line of the cold molecular gas associated with some Halpha filaments surrounding the central galaxy of the Perseus cluster: NGC 1275. The map, extending to about 50 kpc (135 arcsec) from the center of the galaxy, has been made with the 18-receiver array HERA, at the focus of the IRAM 30m telescope. Although most of the cold gas is concentrated to the center of the galaxy, the CO emission is also clearly associated to the extended filaments conspicuous in ionised gas and could trace a possible reservoir fueling the star formation there. Some of the CO emission is also found where the X-ray gas could cool down more efficiently: at the rims of the central X-ray cavity (w...

  1. High-Temperature Gas-Cooled Reactor Technology Development Program: Annual progress report for period ending December 31, 1987

    Energy Technology Data Exchange (ETDEWEB)

    Jones, J.E.,Jr.; Kasten, P.R.; Rittenhouse, P.L.; Sanders, J.P.

    1989-03-01

    The High-Temperature Gas-Cooled Reactor (HTGR) Program being carried out under the US Department of Energy (DOE) continues to emphasize the development of modular high-temperature gas-cooled reactors (MHTGRs) possessing a high degree of inherent safety. The emphasis at this time is to develop the preliminary design of the reference MHTGR and to develop the associated technology base and licensing infrastructure in support of future reactor deployment. A longer-term objective is to realize the full high-temperature potential of HTGRs in gas turbine and high-temperature, process-heat applications. This document summarizes the activities of the HTGR Technology Development Program for the period ending December 31, 1987.

  2. Instability in Shocked Granular Gases

    CERN Document Server

    Sirmas, Nick; Radulescu, Matei

    2013-01-01

    Shocks in granular media, such as vertically oscillated beds, have been shown to develop instabilities. Similar jet formation has been observed in explosively dispersed granular media. Our previous work addressed this instability by performing discrete-particle simulations of inelastic media undergoing shock compression. By allowing finite dissipation within the shock wave, instability manifests itself as distinctive high density non-uniformities and convective rolls within the shock structure. In the present study we have extended this work to investigate this instability at the continuum level. We modeled the Euler equations for granular gases with a modified cooling rate to include an impact velocity threshold necessary for inelastic collisions. Our results showed a fair agreement between the continuum and discrete-particle models. Discrepancies, such as higher frequency instabilities in our continuum results may be attributed to the absence of higher order effects.

  3. Instability in shocked granular gases

    Science.gov (United States)

    Sirmas, Nick; Falle, Sam; Radulescu, Matei

    2014-05-01

    Shocks in granular media, such as vertically oscillated beds, have been shown to develop instabilities. Similar jet formation has been observed in explosively dispersed granular media. Our previous work addressed this instability by performing discrete-particle simulations of inelastic media undergoing shock compression. By allowing finite dissipation within the shock wave, instability manifests itself as distinctive high density non-uniformities and convective rolls within the shock structure. In the present study we have extended this work to investigate this instability at the continuum level. We modeled the Euler equations for granular gases with a modified cooling rate to include an impact velocity threshold necessary for inelastic collisions. Our results showed a fair agreement between the continuum and discrete-particle models. Discrepancies, such as higher frequency instabilities in our continuum results may be attributed to the absence of higher order effects.

  4. Gas cooling in semi-analytic models and smoothed particle hydrodynamics simulations: are results consistent?

    Science.gov (United States)

    Saro, A.; De Lucia, G.; Borgani, S.; Dolag, K.

    2010-08-01

    We present a detailed comparison between the galaxy populations within a massive cluster, as predicted by hydrodynamical smoothed particle hydrodynamics (SPH) simulations and by a semi-analytic model (SAM) of galaxy formation. Both models include gas cooling and a simple prescription of star formation, which consists in transforming instantaneously any cold gas available into stars, while neglecting any source of energy feedback. This simplified comparison is thus not meant to be compared with observational data, but is aimed at understanding the level of agreement, at the stripped-down level considered, between two techniques that are widely used to model galaxy formation in a cosmological framework and which present complementary advantages and disadvantages. We find that, in general, galaxy populations from SAMs and SPH have similar statistical properties, in agreement with previous studies. However, when comparing galaxies on an object-by-object basis, we find a number of interesting differences: (i) the star formation histories of the brightest cluster galaxies (BCGs) from SAM and SPH models differ significantly, with the SPH BCG exhibiting a lower level of star formation activity at low redshift, and a more intense and shorter initial burst of star formation with respect to its SAM counterpart; (ii) while all stars associated with the BCG were formed in its progenitors in the SAM used here, this holds true only for half of the final BCG stellar mass in the SPH simulation, the remaining half being contributed by tidal stripping of stars from the diffuse stellar component associated with galaxies accreted on the cluster halo; (iii) SPH satellites can lose up to 90 per cent of their stellar mass at the time of accretion, due to tidal stripping, a process not included in the SAM used in this paper; (iv) in the SPH simulation, significant cooling occurs on the most massive satellite galaxies and this lasts for up to 1 Gyr after accretion. This physical process is

  5. Correlation of voidage and stress of granular materials in a packed moving bed accompanied with gas flow; Gasu nagare wo tomonau funtai idoso ni okeru kugekiritsu to funtaiatsu no kankei ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Tomoyasu, Yoshitada. [Sanzou Energy Engineering Corp., Okayama (Japan); Yoshino, Fumio.; Iwata, Hiroshi.; Kawazoe, Hiromitsu. [Tottori University, Tottori (Japan). Dept. of Mechanical Engineering

    1999-03-10

    The flow characteristics of granular materials and gas in a vertical packed moving bed, called a [stand pipe], furnished at the bottom of the fluidized bed are investigated theoretically and experimentally. A correlation equation of axial stress {sigma}{sub z} and voidage {epsilon} of granular materials in the stand pipe is proposed through investigations of the continuity equation, the momentum balance equation, Ergun's equation for gas pressure loss and the gas pressure distribution data measured experimentally in the axial direction. Regarding the relation of the axial stress and the voidage, it was recogniged that : 1. The absolute value of d{sigma}{sub z}/d{epsilon} is large at the voidage near the minimum fluidizing condition, and at the voidage in the dense packed condition, and an inflection point of {sigma}{sub z} exists in range between the both conditions ; 2. It seems to be the wall-friction-effect of stand pipe that the absolute value of d{sigma}{sub z}/d{epsilon} is larger at the inlet of stand pipe, and ; 3. The stress is also a function of the particle diameter. The gas flow rate, axial stress distribution of granular materials, gas pressure distribution and voidage distribution in the axial direction of the stand pipe can be calculated from relating equations. (author)

  6. Evaluation of Thermoelectric Properties of Bite Alloys for the Optimization of Gas-Cooled Peltier Current Lead

    Science.gov (United States)

    Fujii, T.; Fukuda, S.; Kawahara, T.; Emoto, M.; Sugino, M.; Sun, J.; Hamabe, M.; Watanabe, H.; Yamaguchi, S.

    2010-04-01

    A direct current superconducting power transmission (DC-SCPT) test facility with 20-meter power cable has been developed in Chubu University. Heat leakage through current leads dominates in case of short-distance DC-SCPT. To solve this problem, we have developed special Peltier current lead (PCL) with bismuth telluride (BiTe) alloy is used as a Peltier material, and have studied a gas-cooled PCL as a novel type current lead for higher reduction of the heat leakage. In order to achieve high efficiency, highest thermoelectric figure of merit material is important to be used especially at low temperature conditions. In our work we measured the thermoelectric properties of BiTe samples, and optimized geometry of PCL by the numerical calculations. It was fount that the heat leakages through PCL and gas-cooled PCL are reduced to 55% and to 36% of the conventional copper current lead (CCL) at the self-cooling condition, correspondingly. PCL can reduce the total electric power consumption of the whole system. We also discuss the heat exchange ratio for the gas-cooled PCL, and extend this approach for further reduction of the heat leakage.

  7. Comparative analysis of steady state heat transfer in a TBC and functionally graded air cooled gas turbine blade

    Indian Academy of Sciences (India)

    Nilanjan Coomar; Ravikiran Kadoli

    2010-02-01

    Internal cooling passages and thermal barrier coatings (TBCs) are presently used to control metal temperatures in gas turbine blades. Functionally graded materials (FGMs), which are typically mixtures of ceramic and metal, have been proposed for use in turbine blades because they possess smooth property gradients thereby rendering them more durable under thermal loads. In the present work, a functionally graded model of an air-cooled turbine blade with airfoil geometry conforming to the NACA0012 is developed which is then used in a finite element algorithm to obtain a non-linear steady state solution to the heat equation for the blade under convection and radiation boundary conditions. The effects of external gas temperature, coolant temperature, surface emissivity changes and different average ceramic/metal content of the blade on the temperature distributions are examined. Simulations are also carried out to compare cooling effectiveness of functionally graded blades with that of blades having TBC. The results highlight the effect of including radiation in the simulation and also indicate that external gas temperature influences the blade heat transfer more strongly. It is also seen that graded blades with about 70% ceramic content can deliver better cooling effectiveness than conventional blades with TBC.

  8. Viscosity, pressure and support of the gas in simulations of merging cool-core clusters

    Science.gov (United States)

    Schmidt, W.; Byrohl, C.; Engels, J. F.; Behrens, C.; Niemeyer, J. C.

    2017-09-01

    Major mergers are considered to be a significant source of turbulence in clusters. We performed a numerical simulation of a major merger event using nested-grid initial conditions, adaptive mesh refinement, radiative cooling of primordial gas and a homogeneous ultraviolet background. By calculating the microscopic viscosity on the basis of various theoretical assumptions and estimating the Kolmogorov length from the turbulent dissipation rate computed with a subgrid-scale model, we are able to demonstrate that most of the warm-hot intergalactic mediums can sustain a fully turbulent state only if the magnetic suppression of the viscosity is considerable. Accepting this as premise, it turns out that ratios of turbulent and thermal quantities change only little in the course of the merger. This confirms the tight correlations between the mean thermal and non-thermal energy content for large samples of clusters in earlier studies, which can be interpreted as second self-similarity on top of the self-similarity for different halo masses. Another long-standing question is how and to which extent turbulence contributes to the support of the gas against gravity. From a global perspective, the ratio of turbulent and thermal pressures is significant for the clusters in our simulation. On the other hand, a local measure is provided by the compression rate, i.e. the growth rate of the divergence of the flow. Particularly for the intracluster medium, we find that the dominant contribution against gravity comes from thermal pressure, while compressible turbulence effectively counteracts the support. For this reason, it appears to be too simplistic to consider turbulence merely as an effective enhancement of thermal energy.

  9. Approaches to experimental validation of high-temperature gas-cooled reactor components

    Energy Technology Data Exchange (ETDEWEB)

    Belov, S.E. [Joint Stock Company ' Afrikantov OKB Mechanical Engineering' , Burnakovsky Proezd, 15, Nizhny Novgorod 603074 (Russian Federation); Borovkov, M.N., E-mail: borovkov@okbm.nnov.ru [Joint Stock Company ' Afrikantov OKB Mechanical Engineering' , Burnakovsky Proezd, 15, Nizhny Novgorod 603074 (Russian Federation); Golovko, V.F.; Dmitrieva, I.V.; Drumov, I.V.; Znamensky, D.S.; Kodochigov, N.G. [Joint Stock Company ' Afrikantov OKB Mechanical Engineering' , Burnakovsky Proezd, 15, Nizhny Novgorod 603074 (Russian Federation); Baxi, C.B.; Shenoy, A.; Telengator, A. [General Atomics, 3550 General Atomics Court, CA (United States); Razvi, J., E-mail: Junaid.Razvi@ga.com [General Atomics, 3550 General Atomics Court, CA (United States)

    2012-10-15

    Highlights: Black-Right-Pointing-Pointer Computational and experimental investigations of thermal and hydrodynamic characteristics for the equipment. Black-Right-Pointing-Pointer Vibroacoustic investigations. Black-Right-Pointing-Pointer Studies of the electromagnetic suspension system on GT-MHR turbo machine rotor models. Black-Right-Pointing-Pointer Experimental investigations of the catcher bearings design. - Abstract: The special feature of high-temperature gas-cooled reactors (HTGRs) is stressed operating conditions for equipment due to high temperature of the primary circuit helium, up to 950 Degree-Sign C, as well as acoustic and hydrodynamic loads upon the gas path elements. Therefore, great significance is given to reproduction of real operation conditions in tests. Experimental investigation of full-size nuclear power plant (NPP) primary circuit components is not practically feasible because costly test facilities will have to be developed for the power of up to hundreds of megawatts. Under such conditions, the only possible process to validate designs under development is representative tests of smaller scale models and fragmentary models. At the same time, in order to take in to validated account the effect of various physical factors, it is necessary to ensure reproduction of both individual processes and integrated tests incorporating needed integrated investigations. Presented are approaches to experimental validation of thermohydraulic and vibroacoustic characteristics for main equipment components and primary circuit path elements under standard loading conditions, which take account of their operation in the HTGR. Within the framework of the of modular helium reactor project, including a turbo machine in the primary circuit, a new and difficult problem is creation of multiple-bearing flexible vertical rotor. Presented are approaches to analytical and experimental validation of the rotor electromagnetic bearings, catcher bearings, flexible rotor

  10. Cryodeposition of nitrogen gas on a surface cooled by helium II

    Energy Technology Data Exchange (ETDEWEB)

    Dhuley, R. C.; Bosque, E. S.; Van Sciver, S. W. [Cryogenics Group, National High Magnetic Field Laboratory, Tallahassee, FL 32310 USA and Mechanical Engineering Department, FAMU-FSU College of Engineering, Tallahassee, FL 32310 (United States)

    2014-01-29

    Catastrophic loss of beam tube vacuum in a superconducting particle accelerator can be simulated by sudden venting of a long high vacuum channel cooled on its outer surface by He II. The rapid rush of atmospheric air in such an event shows an interesting propagation effect, which is much slower than the shock wave that occurs with vacuum loss at ambient conditions. This is due to flash frosting/deposition of air on the cold walls of the channel. Hence to characterize the propagation as well as the associated heat transfer, it is first necessary to understand the deposition process. Here we attempt to model the growth of nitrogen frost layer on a cold plate in order to estimate its thickness with time. The deposition process can be divided into two regimes- free molecular and continuum. It is shown that in free molecular regime, the frost growth can be modeled reasonably well using cryopump theory and general heat transfer relations. The continuum regime is more complex to model, given the higher rate of gas incident on cryosurface causing a large heat load on helium bath and changing cryosurface temperature. Results from the continuum regime are discussed in the context of recent experiments performed in our laboratory.

  11. Effect of Target Configuration on the Neutronic Performance of the Gas-Cooled ADS

    CERN Document Server

    Biss, K; Shetty, N; Nabbi, R

    2013-01-01

    With the utilization of nuclear energy transuranic elements like Pu, Am and Cm are produced causing high, long term radioactivity and radio toxicity, respectively. To reduce the radiological impact on the environment and to the repository Partitioning and Transmutation is considered as an efficient way. In this respect comprehensive research works are performed at different research institutes worldwide. The results show that the transmutation of TRU is achieved with fast neutrons due to the higher fission probability. Based on Accelerator Driven Systems (ADS) those neutrons are used in a particular system, in which mainly liquid metal eutectic (lead bismuth) is used as coolant. The neutronic performance of an ADS system based on gas cooling was studied in this work by using the simulation tool MCNPX. The usage of the Monte-Carlo method in MCNPX allows the simulation of the physical processes in a 3D-model of the core. In dependence of the spallation target material and design several parameters like the mult...

  12. Validation of SCALE for High Temperature Gas-Cooled Reactors Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ilas, Germina [ORNL; Ilas, Dan [ORNL; Kelly, Ryan P [ORNL; Sunny, Eva E [ORNL

    2012-08-01

    This report documents verification and validation studies carried out to assess the performance of the SCALE code system methods and nuclear data for modeling and analysis of High Temperature Gas-Cooled Reactor (HTGR) configurations. Validation data were available from the International Handbook of Evaluated Reactor Physics Benchmark Experiments (IRPhE Handbook), prepared by the International Reactor Physics Experiment Evaluation Project, for two different HTGR designs: prismatic and pebble bed. SCALE models have been developed for HTTR, a prismatic fuel design reactor operated in Japan and HTR-10, a pebble bed reactor operated in China. The models were based on benchmark specifications included in the 2009, 2010, and 2011 releases of the IRPhE Handbook. SCALE models for the HTR-PROTEUS pebble bed configuration at the PROTEUS critical facility in Switzerland have also been developed, based on benchmark specifications included in a 2009 IRPhE draft benchmark. The development of the SCALE models has involved a series of investigations to identify particular issues associated with modeling the physics of HTGRs and to understand and quantify the effect of particular modeling assumptions on calculation-to-experiment comparisons.

  13. Effect of Fuel Fraction on Small Modified CANDLE Burn-up Based Gas Cooled Fast Reactors

    Science.gov (United States)

    Ariani, Menik; Su'ud, Zaki; Waris, Abdul; Khairurrijal, Asiah, Nur; Shafii, M. Ali

    2010-12-01

    A conceptual design study of Gas Cooled Fast Reactors with Modified CANDLE Burn-up has been performed. The objective of this research is to get optimal design parameters of such type reactors. The parameters of nuclear design including the critical condition, conversion ratio, and burn-up level were compared. These parameters are calculated by variation in the fuel fraction 47.5% up to 70%. Two dimensional full core multi groups diffusion calculations was performed by CITATION code. Group constant preparations are performed by using SRAC code system with JENDL-3.2 nuclear data library. In this design the reactor cores with cylindrical cell two dimensional R-Z core models are subdivided into several parts with the same volume in the axial directions. The placement of fuel in core arranged so that the result of plutonium from natural uranium can be utilized optimally for 10 years reactor operation. Modified CANDLE burn-up was established successfully in a core radial width 1.4 m. Total thermal power output for reference core is 550 MW. Study on the effect of fuel to coolant ratio shows that effective multiplication factor (keff) is in almost linear relations with the change of the fuel volume to coolant ratio.

  14. A 50-100 kWe gas-cooled reactor for use on Mars.

    Energy Technology Data Exchange (ETDEWEB)

    Peters, Curtis D. (.)

    2006-04-01

    In the space exploration field there is a general consensus that nuclear reactor powered systems will be extremely desirable for future missions to the outer solar system. Solar systems suffer from the decreasing intensity of solar radiation and relatively low power density. Radioisotope Thermoelectric Generators are limited to generating a few kilowatts electric (kWe). Chemical systems are short-lived due to prodigious fuel use. A well designed 50-100 kWe nuclear reactor power system would provide sufficient power for a variety of long term missions. This thesis will present basic work done on a 50-100 kWe reactor power system that has a reasonable lifespan and would function in an extraterrestrial environment. The system will use a Gas-Cooled Reactor that is directly coupled to a Closed Brayton Cycle (GCR-CBC) power system. Also included will be some variations on the primary design and their effects on the characteristics of the primary design. This thesis also presents a variety of neutronics related calculations, an examination of the reactor's thermal characteristics, feasibility for use in an extraterrestrial environment, and the reactor's safety characteristics in several accident scenarios. While there has been past work for space reactors, the challenges introduced by thin atmospheres like those on Mars have rarely been considered.

  15. A Compact Gas-Cooled Fast Reactor with an Ultra-Long Fuel Cycle

    Directory of Open Access Journals (Sweden)

    Hangbok Choi

    2013-01-01

    Full Text Available In an attempt to allow nuclear power to reach its full economic potential, General Atomics is developing the Energy Multiplier Module (EM2, which is a compact gas-cooled fast reactor (GFR. The EM2 augments its fissile fuel load with fertile materials to enhance an ultra-long fuel cycle based on a “convert-and-burn” core design which converts fertile material to fissile fuel and burns it in situ over a 30-year core life without fuel supplementation or shuffling. A series of reactor physics trade studies were conducted and a baseline core was developed under the specific physics design requirements of the long-life small reactor. The EM2 core performance was assessed for operation time, fuel burnup, excess reactivity, peak power density, uranium utilization, etc., and it was confirmed that an ultra-long fuel cycle core is feasible if the conversion is enough to produce fissile material and maintain criticality, the amount of matrix material is minimized not to soften the neutron spectrum, and the reactor core size is optimized to minimize the neutron loss. This study has shown the feasibility, from the reactor physics standpoint, of a compact GFR that can meet the objectives of ultra-long fuel cycle, factory-fabrication, and excellent fuel utilization.

  16. Procedure of Active Residual Heat Removal after Emergency Shutdown of High-Temperature-Gas-Cooled Reactor

    Directory of Open Access Journals (Sweden)

    Xingtuan Yang

    2014-01-01

    Full Text Available After emergency shutdown of high-temperature-gas-cooled reactor, the residual heat of the reactor core should be removed. As the natural circulation process spends too long period of time to be utilized, an active residual heat removal procedure is needed, which makes use of steam generator and start-up loop. During this procedure, the structure of steam generator may suffer cold/heat shock because of the sudden load of coolant or hot helium at the first few minutes. Transient analysis was carried out based on a one-dimensional mathematical model for steam generator and steam pipe of start-up loop to achieve safety and reliability. The results show that steam generator should be discharged and precooled; otherwise, boiling will arise and introduce a cold shock to the boiling tubes and tube sheet when coolant began to circulate prior to the helium. Additionally, in avoiding heat shock caused by the sudden load of helium, the helium circulation should be restricted to start with an extreme low flow rate; meanwhile, the coolant of steam generator (water should have flow rate as large as possible. Finally, a four-step procedure with precooling process of steam generator was recommended; sensitive study for the main parameters was conducted.

  17. CFD Analysis of the Fuel Temperature in High Temperature Gas-Cooled Reactors

    Energy Technology Data Exchange (ETDEWEB)

    In, W. K.; Chun, T. H.; Lee, W. J.; Chang, J. H. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    2005-07-01

    High temperature gas-cooled reactors (HTGR) have received a renewed interest as potential sources for future energy needs, particularly for a hydrogen production. Among the HTGRs, the pebble bed reactor (PBR) and a prismatic modular reactor (PMR) are considered as the nuclear heat source in Korea's nuclear hydrogen development and demonstration project. PBR uses coated fuel particles embedded in spherical graphite fuel pebbles. The fuel pebbles flow down through the core during an operation. PMR uses graphite fuel blocks which contain cylindrical fuel compacts consisting of the fuel particles. The fuel blocks also contain coolant passages and locations for absorber and control material. The maximum fuel temperature in the core hot spot is one of the important design parameters for both PBR and PMR. The objective of this study is to predict the fuel temperature distributions in PBR and PMR using a computational fluid dynamics(CFD) code, CFX-5. The reference reactor designs used in this analysis are PBMR400 and GT-MHR600.

  18. Gas-cooled fast reactor fuel-cost assessment. Final report, October 1978-September 1979

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, M.L.

    1979-01-01

    This program, contracted to provide a Gas Cooled Fast Reactor (GCFR) fuel assembly fabrication cost assessment, comprised the following basic activities: establish agreement on the ground rules for cost assessment, prepare a fuel factory flow sheet, and prepare a cost assessment for fuel assembly fabrication. Two factory sizes, 250 and 25 MTHM/year, were considered for fuel assembly fabrication cost assessment. The work on this program involved utilizing GE LMFBR cost assessment and fuel factory studies experience to provide a cost assessment of GCFR fuel assembly fabrication. The recent impact of highly sensitive safety and safeguards environment policies on fuel factory containment, safety, quality assurance and safeguards costs are significantly higher than might have been expected just a few years ago. Fuel assembly fabrication costs are significant because they represent an estimated 30 to 60% of the total fuel cycle costs. In light of the relative high cost of fabrication, changes in the core and assembly design may be necessary in order to enhance the overall fuel cycle economics. Fabrication costs are based on similar operations and experience used in other fuel cycle studies. Because of extrapolation of present technology (e.g., remote fuel fabrication versus present contact fabrication) and regulatory requirements, conservative cost estimates were made.

  19. Coupling of Modular High-Temperature Gas-Cooled Reactor with Supercritical Rankine Cycle

    Directory of Open Access Journals (Sweden)

    Shutang Zhu

    2008-01-01

    Full Text Available This paper presents investigations on the possible combination of modular high-temperature gas-cooled reactor (MHTGR technology with the supercritical (SC steam turbine technology and the prospective deployments of the MHTGR SC power plant. Energy conversion efficiency of steam turbine cycle can be improved by increasing the main steam pressure and temperature. Investigations on SC water reactor (SCWR reveal that the development of SCWR power plants still needs further research and development. The MHTGR SC plant coupling the existing technologies of current MHTGR module design with operation experiences of SC FPP will achieve high cycle efficiency in addition to its inherent safety. The standard once-reheat SC steam turbine cycle and the once-reheat steam cycle with life-steam have been studied and corresponding parameters were computed. Efficiencies of thermodynamic processes of MHTGR SC plants were analyzed, while comparisons were made between an MHTGR SC plant and a designed advanced passive PWR - AP1000. It was shown that the net plant efficiency of an MHTGR SC plant can reach 45% or above, 30% higher than that of AP1000 (35% net efficiency. Furthermore, an MHTGR SC plant has higher environmental competitiveness without emission of greenhouse gases and other pollutants.

  20. Modular High Temperature Gas-Cooled Reactor Safety Basis and Approach

    Energy Technology Data Exchange (ETDEWEB)

    David Petti; Jim Kinsey; Dave Alberstein

    2014-01-01

    Various international efforts are underway to assess the safety of advanced nuclear reactor designs. For example, the International Atomic Energy Agency has recently held its first Consultancy Meeting on a new cooperative research program on high temperature gas-cooled reactor (HTGR) safety. Furthermore, the Generation IV International Forum Reactor Safety Working Group has recently developed a methodology, called the Integrated Safety Assessment Methodology, for use in Generation IV advanced reactor technology development, design, and design review. A risk and safety assessment white paper is under development with respect to the Very High Temperature Reactor to pilot the Integrated Safety Assessment Methodology and to demonstrate its validity and feasibility. To support such efforts, this information paper on the modular HTGR safety basis and approach has been prepared. The paper provides a summary level introduction to HTGR history, public safety objectives, inherent and passive safety features, radionuclide release barriers, functional safety approach, and risk-informed safety approach. The information in this paper is intended to further the understanding of the modular HTGR safety approach. The paper gives those involved in the assessment of advanced reactor designs an opportunity to assess an advanced design that has already received extensive review by regulatory authorities and to judge the utility of recently proposed new methods for advanced reactor safety assessment such as the Integrated Safety Assessment Methodology.

  1. Gas Cooled Fast Reactor Research and Development in the European Union

    Directory of Open Access Journals (Sweden)

    Richard Stainsby

    2009-01-01

    Full Text Available Gas-cooled fast reactor (GFR research is directed towards fulfilling the ambitious goals of Generation IV (Gen IV, that is, to develop a safe, sustainable, reliable, proliferation-resistant and economic nuclear energy system. The research is directed towards developing the GFR as an economic electricity generator, with good safety and sustainability characteristics. Fast reactors maximise the usefulness of uranium resources by breeding plutonium and can contribute to minimising both the quantity and radiotoxicity nuclear waste by actinide transmutation in a closed fuel cycle. Transmutation is particularly effective in the GFR core owing to its inherently hard neutron spectrum. Further, GFR is suitable for hydrogen production and process heat applications through its high core outlet temperature. As such GFR can inherit the non-electricity applications that will be developed for thermal high temperature reactors in a sustainable manner. The Euratom organisation provides a route by which researchers in all European states, and other non-European affiliates, can contribute to the Gen IV GFR system. This paper summarises the achievements of Euratom's research into the GFR system, starting with the 5th Framework programme (FP5 GCFR project in 2000, through FP6 (2005 to 2009 and looking ahead to the proposed activities within the 7th Framework Programme (FP7.

  2. HYBRID SULFUR CYCLE FLOWSHEETS FOR HYDROGEN PRODUCTION USING HIGH-TEMPERATURE GAS-COOLED REACTORS

    Energy Technology Data Exchange (ETDEWEB)

    Gorensek, M.

    2011-07-06

    Two hybrid sulfur (HyS) cycle process flowsheets intended for use with high-temperature gas-cooled reactors (HTGRs) are presented. The flowsheets were developed for the Next Generation Nuclear Plant (NGNP) program, and couple a proton exchange membrane (PEM) electrolyzer for the SO2-depolarized electrolysis step with a silicon carbide bayonet reactor for the high-temperature decomposition step. One presumes an HTGR reactor outlet temperature (ROT) of 950 C, the other 750 C. Performance was improved (over earlier flowsheets) by assuming that use of a more acid-tolerant PEM, like acid-doped poly[2,2'-(m-phenylene)-5,5'-bibenzimidazole] (PBI), instead of Nafion{reg_sign}, would allow higher anolyte acid concentrations. Lower ROT was accommodated by adding a direct contact exchange/quench column upstream from the bayonet reactor and dropping the decomposition pressure. Aspen Plus was used to develop material and energy balances. A net thermal efficiency of 44.0% to 47.6%, higher heating value basis is projected for the 950 C case, dropping to 39.9% for the 750 C case.

  3. THR-TH: a high-temperature gas-cooled nuclear reactor core thermal hydraulics code

    Energy Technology Data Exchange (ETDEWEB)

    Vondy, D.R.

    1984-07-01

    The ORNL version of PEBBLE, the (RZ) pebble bed thermal hydraulics code, has been extended for application to a prismatic gas cooled reactor core. The supplemental treatment is of one-dimensional coolant flow in up to a three-dimensional core description. Power density data from a neutronics and exposure calculation are used as the basic information for the thermal hydraulics calculation of heat removal. Two-dimensional neutronics results may be expanded for a three-dimensional hydraulics calculation. The geometric description for the hydraulics problem is the same as used by the neutronics code. A two-dimensional thermal cell model is used to predict temperatures in the fuel channel. The capability is available in the local BOLD VENTURE computation system for reactor core analysis with capability to account for the effect of temperature feedback by nuclear cross section correlation. Some enhancements have also been added to the original code to add pebble bed modeling flexibility and to generate useful auxiliary results. For example, an estimate is made of the distribution of fuel temperatures based on average and extreme conditions regularly calculated at a number of locations.

  4. Optimization of intermediate cooling and intermediate heating in the gas turbine process; Optimierung der Zwischenkuehlung und der Zwischenerhitzung beim Gasturbinenprozess

    Energy Technology Data Exchange (ETDEWEB)

    Woerrlein, K.

    1998-07-01

    The author investigated how the thermal efficiency of the gas turbine process can be improved by intermediate cooling, intermediate heating, or combined intermediate cooling and heating. The focus was on the pressure ratios of low-pressure compressors and high-pressure turbines. The numeric calculations were carried out using real gas characteristics. The findings suggest that intermediate coling inside the compressor has much more influence on the thermal efficiency than intermediate heating inside the turbine. However, the latter is advantageous in the case of gas turbines for combined cycle operation, as the off-gas temperatures required for steam generation are reached even at relatively low turbine inlet temperatures, so that NOx emissions of the gas turbine combustion chamber will be low. It is recommended that solitary gas turbines should be operated with intermediate cooling and gas turbines in combined cycle operation with intermediate heating. [German] In der vorliegenden Arbeit soll untersucht werden, in welcher Weise sich der thermische Wirkungsgrad des Gasturbinen-Prozesses durch Zwischenkuehlung, Zwischenerhitzung bzw. Zwischenkuehlung und Zwischenerhitzung verbessern laesst. Dabei sollen in erster Linie die Druckverhaeltnisse von ND-Verdichter bzw. HD-Turbine bestimmt werden, bei denen Zwischenkuehlung und Zwischenerhitzung vorgenommen werden sollen, um eine optimale Verbesserung des thermischen Wirkungsgrades zu erreichen. Die numerische Durchrechnung soll mit den Stoffwerten des realen Gases durchgefuehrt werden. Die numerischen Ergebnisse zeigen, dass die Zwischenkuehlung im Verdichter einen weit groesseren Einfluss auf den thermischen Wirkungsgrad hat als die Zwischenerhitzung in der Turbine. Letztere ist aber bei Gasturbinen fuer den Kombibetrieb von Vorteil, erreicht man doch die fuer die Dampferzeugung notwendigen Abgastemperaturen der Gasturbine schon bei relativ niedrigen Turbineneintrittstemperaturen, so dass die NO{sub x}-Emission der

  5. TRISO-Coated Fuel Processing to Support High Temperature Gas-Cooled Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Del Cul, G.D.

    2002-10-01

    The initial objective of the work described herein was to identify potential methods and technologies needed to disassemble and dissolve graphite-encapsulated, ceramic-coated gas-cooled-reactor spent fuels so that the oxide fuel components can be separated by means of chemical processing. The purpose of this processing is to recover (1) unburned fuel for recycle, (2) long-lived actinides and fission products for transmutation, and (3) other fission products for disposal in acceptable waste forms. Follow-on objectives were to identify and select the most promising candidate flow sheets for experimental evaluation and demonstration and to address the needs to reduce technical risks of the selected technologies. High-temperature gas-cooled reactors (HTGRs) may be deployed in the next -20 years to (1) enable the use of highly efficient gas turbines for producing electricity and (2) provide high-temperature process heat for use in chemical processes, such as the production of hydrogen for use as clean-burning transportation fuel. Also, HTGR fuels are capable of significantly higher burn-up than light-water-reactor (LWR) fuels or fast-reactor (FR) fuels; thus, the HTGR fuels can be used efficiently for transmutation of fissile materials and long-lived actinides and fission products, thereby reducing the inventory of such hazardous and proliferation-prone materials. The ''deep-burn'' concept, described in this report, is an example of this capability. Processing of spent graphite-encapsulated, ceramic-coated fuels presents challenges different from those of processing spent LWR fuels. LWR fuels are processed commercially in Europe and Japan; however, similar infrastructure is not available for processing of the HTGR fuels. Laboratory studies on the processing of HTGR fuels were performed in the United States in the 1960s and 1970s, but no engineering-scale processes were demonstrated. Currently, new regulations concerning emissions will impact the

  6. Study on disposal method of graphite blocks and storage of spent fuel for modular gas-cooled reactor. Joint research

    Energy Technology Data Exchange (ETDEWEB)

    Sumita, Junya; Sawa, Kazuhiro; Kunitomi, Kazuhiko [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment; Tsuchie, Yasuo; Urakami, Masao [Japan Atomic Power Co., Tokyo (Japan)

    2003-02-01

    This report describes the result of study on disposal method of graphite blocks in future block-type reactor. Present study was carried out within a framework of joint research, ''Research of Modular High Temperature Gas-cooled Reactors (No. 3)'', between Japan Atomic Energy Research Institute (JAERI) and the Japan Atomic Power Company (JAPCO), in 2000. In this study, activities in fuel and reflector graphite blocks were evaluated and were compared with the disposal limits defined as low-level of radioactive waste. As a result, it was found that the activity for only C-14 was higher than disposal limits for the low-level of radioactive waste and that the amount of air in the graphite is important to evaluate precisely of C-14 activity. In addition, spent fuels can be stored in air-cooled condition at least after two years cooling in the storage pool. (author)

  7. A method for calculation of forces acting on air cooled gas turbine blades based on the aerodynamic theory

    Directory of Open Access Journals (Sweden)

    Grković Vojin R.

    2013-01-01

    Full Text Available The paper presents the mathematical model and the procedure for calculation of the resultant force acting on the air cooled gas turbine blade(s based on the aerodynamic theory and computation of the circulation around the blade profile. In the conducted analysis was examined the influence of the cooling air mass flow expressed through the cooling air flow parameter λc, as well as, the values of the inlet and outlet angles β1 and β2, on the magnitude of the tangential and axial forces. The procedure and analysis were exemplified by the calculation of the tangential and axial forces magnitudes. [Projekat Ministarstva nauke Republike Srbije: Development and building the demonstrative facility for combined heat and power with gasification

  8. ANALYSIS OF A HIGH TEMPERATURE GAS-COOLED REACTOR POWERED HIGH TEMPERATURE ELECTROLYSIS HYDROGEN PLANT

    Energy Technology Data Exchange (ETDEWEB)

    M. G. McKellar; E. A. Harvego; A. M. Gandrik

    2010-11-01

    An updated reference design for a commercial-scale high-temperature electrolysis (HTE) plant for hydrogen production has been developed. The HTE plant is powered by a high-temperature gas-cooled reactor (HTGR) whose configuration and operating conditions are based on the latest design parameters planned for the Next Generation Nuclear Plant (NGNP). The current HTGR reference design specifies a reactor power of 600 MWt, with a primary system pressure of 7.0 MPa, and reactor inlet and outlet fluid temperatures of 322°C and 750°C, respectively. The reactor heat is used to produce heat and electric power to the HTE plant. A Rankine steam cycle with a power conversion efficiency of 44.4% was used to provide the electric power. The electrolysis unit used to produce hydrogen includes 1.1 million cells with a per-cell active area of 225 cm2. The reference hydrogen production plant operates at a system pressure of 5.0 MPa, and utilizes a steam-sweep system to remove the excess oxygen that is evolved on the anode (oxygen) side of the electrolyzer. The overall system thermal-to-hydrogen production efficiency (based on the higher heating value of the produced hydrogen) is 42.8% at a hydrogen production rate of 1.85 kg/s (66 million SCFD) and an oxygen production rate of 14.6 kg/s (33 million SCFD). An economic analysis of this plant was performed with realistic financial and cost estimating The results of the economic analysis demonstrated that the HTE hydrogen production plant driven by a high-temperature helium-cooled nuclear power plant can deliver hydrogen at a competitive cost. A cost of $3.03/kg of hydrogen was calculated assuming an internal rate of return of 10% and a debt to equity ratio of 80%/20% for a reactor cost of $2000/kWt and $2.41/kg of hydrogen for a reactor cost of $1400/kWt.

  9. INVESTIGATION OF FUNDAMENTAL THERMAL-HYDRAULIC PHENOMENA IN ADVANCED GAS-COOLED REACTORS

    Energy Technology Data Exchange (ETDEWEB)

    INVESTIGATION OF FUNDAMENTAL THERMAL-HYDRAULIC PHE

    2006-09-01

    INL LDRD funded research was conducted at MIT to experimentally characterize mixed convection heat transfer in gas-cooled fast reactor (GFR) core channels in collaboration with INL personnel. The GFR for Generation IV has generated considerable interest and is under development in the U.S., France, and Japan. One of the key candidates is a block-core configuration first proposed by MIT, has the potential to operate in Deteriorated Turbulent Heat Transfer (DTHT) regime or in the transition between the DTHT and normal forced or laminar convection regime during post-loss-of-coolant accident (LOCA) conditions. This is contrary to most industrial applications where operation is in a well-defined and well-known turbulent forced convection regime. As a result, important new need emerged to develop heat transfer correlations that make possible rigorous and accurate predictions of Decay Heat Removal (DHR) during post LOCA in these regimes. Extensive literature review on these regimes was performed and a number of the available correlations was collected in: (1) forced laminar, (2) forced turbulent, (3) mixed convection laminar, (4) buoyancy driven DTHT and (5) acceleration driven DTHT regimes. Preliminary analysis on the GFR DHR system was performed and using the literature review results and GFR conditions. It confirmed that the GFR block type core has a potential to operate in the DTHT regime. Further, a newly proposed approach proved that gas, liquid and super critical fluids all behave differently in single channel under DTHT regime conditions, thus making it questionable to extrapolate liquid or supercritical fluid data to gas flow heat transfer. Experimental data were collected with three different gases (nitrogen, helium and carbon dioxide) in various heat transfer regimes. Each gas unveiled different physical phenomena. All data basically covered the forced turbulent heat transfer regime, nitrogen data covered the acceleration driven DTHT and buoyancy driven DTHT

  10. Conceptual Design study of Small Long-life Gas Cooled Fast Reactor With Modified CANDLE Burn-up Scheme

    Science.gov (United States)

    Nur Asiah, A.; Su'ud, Zaki; Ferhat, A.; Sekimoto, H.

    2010-06-01

    In this paper, conceptual design study of Small Long-life Gas Cooled Fast Reactors with Natural Uranium as Fuel Cycle Input has been performed. In this study Gas Cooled Fast Reactor is slightly modified by employing modified CANDLE burn-up scheme so that it can use Natural Uranium as fuel cycle input. Due to their hard spectrum, GCFR in this study showed very good performance in converting U-238 to plutonium in order to maintain the operation condition requirement of long-life reactors. Due to the limitation of thermal hydraulic aspects, the average power density of the proposed design is selected about 70 W/cc. With such condition we got an optimal design of 325 MWt reactors which can be operated 10 years without refueling and fuel shuffling and just need natural uranium as fuel cycle input. The average discharge burn-up is about 290 GWd/ton HM.

  11. High-temperature gas-cooled reactor technology development program. Annual progress report for period ending December 31, 1982

    Energy Technology Data Exchange (ETDEWEB)

    Kasten, P.R.; Rittenhouse, P.L.; Bartine, D.E.; Sanders, J.P.

    1983-06-01

    During 1982 the High-Temperature Gas-Cooled Reactor (HTGR) Technology Program at Oak Ridge National Laboratory (ORNL) continued to develop experimental data required for the design and licensing of cogeneration HTGRs. The program involves fuels and materials development (including metals, graphite, ceramic, and concrete materials), HTGR chemistry studies, structural component development and testing, reactor physics and shielding studies, performance testing of the reactor core support structure, and HTGR application and evaluation studies.

  12. High-temperature gas-cooled reactor technology development program. Annual progress report for period ending December 31, 1982

    Energy Technology Data Exchange (ETDEWEB)

    Kasten, P.R.; Rittenhouse, P.L.; Bartine, D.E.; Sanders, J.P.

    1983-06-01

    During 1982 the High-Temperature Gas-Cooled Reactor (HTGR) Technology Program at Oak Ridge National Laboratory (ORNL) continued to develop experimental data required for the design and licensing of cogeneration HTGRs. The program involves fuels and materials development (including metals, graphite, ceramic, and concrete materials), HTGR chemistry studies, structural component development and testing, reactor physics and shielding studies, performance testing of the reactor core support structure, and HTGR application and evaluation studies.

  13. Thermal investigation of an internally cooled strut injector for scramjet application at moderate and hot gas conditions

    Science.gov (United States)

    Dröske, Nils C.; Förster, Felix J.; Weigand, Bernhard; von Wolfersdorf, Jens

    2017-03-01

    In this paper, we present a combined experimental and numerical approach to assess the thermal loads and the cooling mechanism of an internally cooled strut injector for a supersonic combustion ramjet. Infrared measurements of the injector surface are conducted at a moderate external flow temperature. In addition, the main flow field is investigated with the LITA technique. Main features of the cooling mechanism are identified based on experimental data. However, a full evaluation can only be obtained using a complex, conjugate CFD simulation, which couples the external and internal flow fields to the heat conduction inside the injector body. Furthermore, numerical simulations are also presented for hot gas conditions corresponding to combustion experiments. Both hydrogen, which would be used as fuel for flight tests, and air are considered as coolants. While the main features of the cooling mechanism will be shown to remain unchanged, the combustor wall temperature is found to have a significant influence on the cooling. This emphasizes the importance and the usefulness of such complex conjugate numerical simulations.

  14. DESIGN CHARACTERISTICS OF THE IDAHO NATIONAL LABORATORY HIGH-TEMPERATURE GAS-COOLED TEST REACTOR

    Energy Technology Data Exchange (ETDEWEB)

    Sterbentz, James; Bayless, Paul; Strydom, Gerhard; Kumar, Akansha; Gougar, Hans

    2016-11-01

    Uncertainty and sensitivity analysis is an indispensable element of any substantial attempt in reactor simulation validation. The quantification of uncertainties in nuclear engineering has grown more important and the IAEA Coordinated Research Program (CRP) on High-Temperature Gas Cooled Reactor (HTGR) initiated in 2012 aims to investigate the various uncertainty quantification methodologies for this type of reactors. The first phase of the CRP is dedicated to the estimation of cell and lattice model uncertainties due to the neutron cross sections co-variances. Phase II is oriented towards the investigation of propagated uncertainties from the lattice to the coupled neutronics/thermal hydraulics core calculations. Nominal results for the prismatic single block (Ex.I-2a) and super cell models (Ex.I-2c) have been obtained using the SCALE 6.1.3 two-dimensional lattice code NEWT coupled to the TRITON sequence for cross section generation. In this work, the TRITON/NEWT-flux-weighted cross sections obtained for Ex.I-2a and various models of Ex.I-2c is utilized to perform a sensitivity analysis of the MHTGR-350 core power densities and eigenvalues. The core solutions are obtained with the INL coupled code PHISICS/RELAP5-3D, utilizing a fixed-temperature feedback for Ex. II-1a.. It is observed that the core power density does not vary significantly in shape, but the magnitude of these variations increases as the moderator-to-fuel ratio increases in the super cell lattice models.

  15. Migration of radionuclides in a gas cooled solid state spallation target

    Energy Technology Data Exchange (ETDEWEB)

    Jørgensen, Thomas; Severin, Gregory; Jensen, Mikael, E-mail: kmje@dtu.dk

    2015-02-15

    Highlights: • We have investigated diffusion of (primarily) tritium in solid tungsten. • We have used an analytical and a numerical approach. • The temperature of tungsten changes with a short-term pulse driven proton beam. • The time structure of the temperature has a negligible impact on the diffusion. • Radioactive release at the surface can be found by solving the differential equation. - Abstract: The current design of the ESS (European Spallation Source) program proposes a rotating solid tungsten target cooled by helium gas and a pulsed beam of protons. For safety reasons any design has to address whether or not the induced radionuclidic isotopes in the target migrate. In this paper we have investigated the diffusion of (primarily) tritium in solid tungsten to see if a pulse driven short-term variation in temperature (temperature peaks separated by one turn of the wheel (2.36 s)) could possibly give rise to wave-like migration of the radionuclides, possibly accelerating the overall release. In order to calculate the diffusion in the solid tungsten target two approaches have been used. One neglecting the time structure of the beam and thermal cycling of the target, and one numerical, discrete time step simulation to capture the effects of the thermal cycling on the diffusion behavior. We found that the time structure of the of the temperature has a negligible impact on the diffusion, and that the radioactive release at the surface can be calculated safely by solving the differential equation (Fick's law) using an appropriate temperature to calculate the diffusion constant.

  16. Study on the properties of the fuel compact for High Temperature Gas-cooled Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chung-yong; Lee, Sung-yong; Choi, Min-young; Lee, Seung-jae; Jo, Young-ho [KEPCO Nuclear Fuel, Daejeon (Korea, Republic of); Lee, Young-woo; Cho, Moon-sung [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    High Temperature Gas-cooled Reactors (HTGR), one of the Gen-IV reactors, have been using the fuel element which is manufactured by the graphite matrix, surrounding Tristructural-isotropic (TRISO)-coated Uranium particles. Factors with these characteristics effecting on the matrix of fuel compact are chosen and their impacts on the properties are studied. The fuel elements are considered with two types of concepts for HTGR, which are the block type reactor and the pebble bed reactor. In this paper, the cylinder-formed fuel element for the block type reactor is focused on, which consists of the large part of graphite matrix. One of the most important properties of the graphite matrix is the mechanical strength with the high reliability because the graphite matrix should be enabled to protect the TRISO particles from the irradiation environment and the impact from the outside. In this study, the three kinds of candidate graphites and the two kinds of candidate binder (Phenol and Polyvinyl butyral) were chosen and mixed with each other, formed and heated to measure mechanical properties. The objective of this research is to optimize the materials and composition of the mixture and the forming process by evaluating the mechanical properties before/after carbonization and heat treatment. From the mechanical test results, the mechanical properties of graphite pellets was related to the various conditions such as the contents and kinds of binder, the kinds of graphite and the heat treatments. In the result of the compressive strength and Vicker's hardness, the 10 wt% phenol binder added R+S graphite pellet was relatively higher mechanical properties than other pellets. The contents of Phenol binder, the kinds of graphite powder and the temperature of carbonization and heat treatment are considered important factors for the properties. To optimize the mechanical properties of fuel elements, the role of binders and the properties of graphites will be investigated as

  17. The Gas-Cooled Fast Reactor: Report on Safety System Design for Decay Heat Removal

    Energy Technology Data Exchange (ETDEWEB)

    K. D. Weaver; T. Marshall; T. Y. C. Wei; E. E. Feldman; M. J. Driscoll; H. Ludewig

    2003-09-01

    The gas-cooled fast reactor (GFR) was chosen as one of the Generation IV nuclear reactor systems to be developed based on its excellent potential for sustainability through reduction of the volume and radiotoxicity of both its own fuel and other spent nuclear fuel, and for extending/utilizing uranium resources orders of magnitude beyond what the current open fuel cycle can realize. In addition, energy conversion at high thermal efficiency is possible with the current designs being considered, thus increasing the economic benefit of the GFR. However, research and development challenges include the ability to use passive decay heat removal systems during accident conditions, survivability of fuels and in-core materials under extreme temperatures and radiation, and economical and efficient fuel cycle processes. This report addresses/discusses the decay heat removal options available to the GFR, and the current solutions. While it is possible to design a GFR with complete passive safety (i.e., reliance solely on conductive and radiative heat transfer for decay heat removal), it has been shown that the low power density results in unacceptable fuel cycle costs for the GFR. However, increasing power density results in higher decay heat rates, and the attendant temperature increase in the fuel and core. Use of active movers, or blowers/fans, is possible during accident conditions, which only requires 3% of nominal flow to remove the decay heat. Unfortunately, this requires reliance on active systems. In order to incorporate passive systems, innovative designs have been studied, and a mix of passive and active systems appears to meet the requirements for decay heat removal during accident conditions.

  18. Axisymmetric whole pin life modelling of advanced gas-cooled reactor nuclear fuel

    Science.gov (United States)

    Mella, R.; Wenman, M. R.

    2013-06-01

    Thermo-mechanical contributions to pellet-clad interaction (PCI) in advanced gas-cooled reactors (AGRs) are modelled in the ABAQUS finite element (FE) code. User supplied sub-routines permit the modelling of the non-linear behaviour of AGR fuel through life. Through utilisation of ABAQUS's well-developed pre- and post-processing ability, the behaviour of the axially constrained steel clad fuel was modelled. The 2D axisymmetric model includes thermo-mechanical behaviour of the fuel with time and condition dependent material properties. Pellet cladding gap dynamics and thermal behaviour are also modelled. The model treats heat up as a fully coupled temperature-displacement study. Dwell time and direct power cycling was applied to model the impact of online refuelling, a key feature of the AGR. The model includes the visco-plastic behaviour of the fuel under the stress and irradiation conditions within an AGR core and a non-linear heat transfer model. A multiscale fission gas release model is applied to compute pin pressure; this model is coupled to the PCI gap model through an explicit fission gas inventory code. Whole pin, whole life, models are able to show the impact of the fuel on all segments of cladding including weld end caps and cladding pellet locking mechanisms (unique to AGR fuel). The development of this model in a commercial FE package shows that the development of a potentially verified and future-proof fuel performance code can be created and used. The usability of a FE based fuel performance code would be an enhancement over past codes. Pre- and post-processors have lowered the entry barrier for the development of a fuel performance model to permit the ability to model complicated systems. Typical runtimes for a 5 year axisymmetric model takes less than one hour on a single core workstation. The current model has implemented: Non-linear fuel thermal behaviour, including a complex description of heat flow in the fuel. Coupled with a variety of

  19. Validation of SCALE and the TRITON Depletion Sequence for Gas-Cooled Reactor Analysis

    Energy Technology Data Exchange (ETDEWEB)

    DeHart, Mark D [ORNL; Pritchard, Megan L [ORNL

    2008-01-01

    The very-high-temperature reactor (VHTR) is an advanced reactor concept that uses graphite-moderated fuel and helium gas as a coolant. At present there are two primary VHTR reactor designs under consideration for development: in the pebble-bed reactor, a core is loaded with 'pebbles' consisting of 6 cm diameter spheres, while in a high-temperature gas-cooled reactor, fuel rods are placed within prismatic graphite blocks. In both systems, fuel elements (spheres or rods) are comprised of tristructural-isotropic (TRISO) fuel particles. The TRISO particles are either dispersed in the matrix of a graphite pebble for the pebble-bed design or molded into compacts/rods that are then inserted into the hexagonal graphite blocks for the prismatic concept. Two levels of heterogeneity exist in such fuel designs: (1) microspheres of TRISO particles dispersed in a graphite matrix of a cylindrical or spherical shape, and (2) neutron interactions at the rod-to-rod or sphere-to-sphere level. Such double heterogeneity (DH) provides a challenge to multigroup cross-section processing methods, which must treat each level of heterogeneity separately. A new capability to model doubly heterogeneous systems was added to the SCALE system in the release of Version 5.1. It was included in the control sequences CSAS and CSAS6, which use the Monte Carlo codes KENO V.a and KENO-VI, respectively, for three-dimensional neutron transport analyses and in the TRITON sequence, which uses the two-dimensional lattice physics code NEWT along with both versions of KENO for transport and depletion analyses. However, the SCALE 5.1 version of TRITON did not support the use of the DH approach for depletion. This deficiency has been addressed, and DH depletion will be available as an option in the upcoming release of SCALE 6. At present Oak Ridge National Laboratory (ORNL) staff are developing a set of calculations that may be used to validate SCALE for DH calculations. This paper discusses the

  20. Gas-burning air cooling developed by leading gas enterprises (Toho Gas). Nagoyaka Home Yokota, a nursing home; Ote kakusha ni miru gas reibo no saiyo jirei (Toho Gas). Tokubetsu yogo rojin home `Nagoyaka House Yokota`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    Described herein is the air-conditioning system for Nagoyaka Home Yokota, a nursing home in Nagoya City. It is a 7-story building with a total floor area of 4,444m{sup 2}. The first and second floors are for common purposes (dinning rooms, bathrooms, etc.), and the upper floors are for a total of 39 residents. The air-conditioning system is divided into two lines, one for the residents and the other for offices, where each office is equipped with an individual heat-pump type air conditioner. The residential rooms are air-conditioned by the gas absorption type cool/hot water generating system (capacity: 120 refrigeration tons) installed on the roof, where each room is equipped with a fan coil unit on the ceiling to allow each resident to control temperature independently. The home is also equipped with gas-burning systems for hot water generators, clothes driers and cookers. These city gas burning systems support comfortableness of the home. 5 figs.

  1. Formation of globular clusters in atomic-cooling halos via rapid gas condensation and fragmentation during the epoch of reionization

    CERN Document Server

    Kimm, Taysun; Rosdahl, Joakim; Yi, Sukyoung

    2015-01-01

    We investigate the formation of metal-poor globular clusters (GCs) at the center of two dark matter halos with $M_{halo}\\sim4\\times10^7\\,M_\\odot$ at $z>10$ using cosmological radiation-hydrodynamics simulations. We find that very compact ($\\lesssim$ 1 pc) and massive ($\\sim6\\times10^5\\,M_\\odot$) clusters form rapidly when pristine gas collapses isothermally with the aid of efficient Ly$\\alpha$ emission during the transition from molecular-cooling halos to atomic-cooling halos. Because the local free-fall time of dense star-forming gas is very short ($\\ll 1\\,{\\rm Myr}$), a large fraction of the collapsed gas is turned into stars before stellar feedback processes blow out the gas and shut down star formation. Although the early stage of star formation is limited to a small region of the central star-forming disk, we find that the disk quickly fragments due to metal enrichment from supernovae. Sub-clusters formed in the fragmented clouds eventually merge with the main cluster at the center. We estimate using a s...

  2. An investigation into clustering and segregation in granular materials

    NARCIS (Netherlands)

    Gonzalez Briones, J.S.L.

    2013-01-01

    In this thesis, I studied the dynamics of granular matter by means of theory, simulations, and experiments. I studied how patterns emerge from a seemly unrelated ensemble of grains in different configurations. I focused on cluster formations in free cooling granular gases, developed an algorithm for

  3. Cooling of Gas Turbines I - Effects of Addition of Fins to Blade Tips and Rotor, Admission of Cooling Air Through Part of Nozzles, and Change in Thermal Conductivity of Turbine Components

    Science.gov (United States)

    Brown, Byron

    1947-01-01

    An analysis was developed for calculating the radial temperature distribution in a gas turbine with only the temperatures of the gas and the cooling air and the surface heat-transfer coefficient known. This analysis was applied to determine the temperatures of a complete wheel of a conventional single-stage impulse exhaust-gas turbine. The temperatures were first calculated for the case of the turbine operating at design conditions of speed, gas flow, etc. and with only the customary cooling arising from exposure of the outer blade flange and one face of the rotor to the air. Calculations were next made for the case of fins applied to the outer blade flange and the rotor. Finally the effects of using part of the nozzles (from 0 to 40 percent) for supplying cooling air and the effects of varying the metal thermal conductivity from 12 to 260 Btu per hour per foot per degree Farenheit on the wheel temperatures were determined. The gas temperatures at the nozzle box used in the calculations ranged from 1600F to 2000F. The results showed that if more than a few hundred degrees of cooling of turbine blades are required other means than indirect cooling with fins on the rotor and outer blade flange would be necessary. The amount of cooling indicated for the type of finning used could produce some improvement in efficiency and a large increase in durability of the wheel. The results also showed that if a large difference is to exist between the effective temperature of the exhaust gas and that of the blade material, as must be the case with present turbine materials and the high exhaust-gas temperatures desired (2000F and above), two alternatives are suggested: (a) If metal with a thermal conductivity comparable with copper is used, then the blade temperature can be reduced by strong cooling at both the blade tip and root. The center of the blade will be less than 2000F hotter than the ends; (b) With low conductivity materials some method of direct cooling other than

  4. DESIGN CHARACTERISTICS OF THE IDAHO NATIONAL LABORATORY HIGH-[TEMPERATURE GAS-COOLED TEST REACTOR

    Energy Technology Data Exchange (ETDEWEB)

    Sterbentz, James; Bayless, Paul; Strydom, Gerhard; Kumar, Akansha; Gougar, Hans

    2016-11-01

    A point design for a graphite-moderated, high-temperature, gas-cooled test reactor (HTG TR) has been developed by Idaho National Laboratory (INL) as part of a United States (U.S.) Department of Energy (DOE) initiative to explore and potentially expand the existing U.S. test reactor capabilities. This paper provides a summary of the design and its main attributes. The 200 MW HTG TR is a thermal-neutron spectrum reactor composed of hexagonal prismatic fuel and graphite reflector blocks. Twelve fuel columns (96 fuel blocks total and 6.34 m active core height) are arranged in two hexagonal rings to form a relatively compact, high-power density, annular core sandwiched between inner, outer, top, and bottom graphite reflectors. The HTG-TR is designed to operate at 7 MPa with a coolant inlet/outlet temperature of 325°C/650°C, and utilizes TRISO particle fuel from the DOE AGR Program with 425 ?m uranium oxycarbide (UCO) kernels and an enrichment of 15.5 wt% 235U. The primary mission of the HTG TR is material irradiation and therefore the core has been specifically designed and optimized to provide the highest possible thermal and fast neutron fluxes. The highest thermal neutron flux (3.90E+14 n/cm2s) occurs in the outer reflector, and the maximum fast flux levels (1.17E+14 n/cm2s) are produced in the central reflector column where most of the graphite has been removed. Due to high core temperatures under accident conditions, all the irradiation test facilities have been located in the inner and outer reflectors where fast flux levels decline. The core features a large number of irradiation positions with large test volumes and long test lengths, ideal for thermal neutron irradiation of large test articles. The total available test volume is more than 1100 liters. Up to four test loop facilities can be accommodated with pressure tube boundaries to isolate test articles and test fluids (e.g., liquid metal, liquid salt, light water) from the helium primary coolant system.

  5. Measurement of Turbulent Flow Phenomena for the Lower Plenum of a Prismatic Gas-Cooled Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Hugh M. McIlroy Jr.; Donald M. McEligot; Robert J. Pink; Keith G. Condie; Glenn E. McCreery

    2007-09-01

    Mean velocity field and turbulence data are presented for flow phenomena in a lower plenum of a typical prismatic gas-cooled reactor (GCR), such as in a Very High Temperature Reactor (VHTR) concept. In preparation for design, safety analyses and licensing, research has begun on readying the computational tools that will be needed to predict the thermal-hydraulics behavior of the reactor design. Fluid dynamics experiments have been designed and built to develop benchmark databases for the assessment of computational fluid dynamics (CFD) codes and their turbulence models for a typical VHTR plenum geometry in the limiting case of negligible buoyancy and constant fluid properties. This experiment has been proposed as a “Standard Problem” for assessing advanced reactor (CFD) analysis tools. Present results concentrate on the region of the plenum near its far reflector wall (away from the outlet duct). The flow in the lower plenum can locally be considered as multiple jets into a confined cross flow - with obstructions. A model of the lower plenum has been fabricated and scaled to the geometric dimensions of the Next Generation Nuclear Plant (NGNP) Point Design. The model consists of a row of full circular posts along its centerline with half-posts on the two parallel walls to induce flow features somewhat comparable to those expected from the staggered parallel rows of posts in the reactor design. Posts, side walls and end walls are fabricated from clear, fused quartz to match the refractive-index of the working fluid so that optical techniques may be employed for the measurements. The experiments were conducted in the Matched-Index-of-Refraction (MIR) Facility at the Idaho National Laboratory (INL). The benefit of the MIR technique is that it permits optical measurements to determine complex flow characteristics in passages and around objects to be obtained without locating a disturbing transducer in the flow field and without distortion of the optical paths. The

  6. Development of gas cooled reactors and experimental setup of high temperature helium loop for in-pile operation

    Energy Technology Data Exchange (ETDEWEB)

    Miletić, Marija, E-mail: marija_miletic@live.com [Czech Technical University in Prague, Prague (Czech Republic); Fukač, Rostislav, E-mail: fuk@cvrez.cz [Research Centre Rez Ltd., Rez (Czech Republic); Pioro, Igor, E-mail: Igor.Pioro@uoit.ca [University of Ontario Institute of Technology, Oshawa (Canada); Dragunov, Alexey, E-mail: Alexey.Dragunov@uoit.ca [University of Ontario Institute of Technology, Oshawa (Canada)

    2014-09-15

    Highlights: • Gas as a coolant in Gen-IV reactors, history and development. • Main physical parameters comparison of gas coolants: carbon dioxide, helium, hydrogen with water. • Forced convection in turbulent pipe flow. • Gas cooled fast reactor concept comparisons to very high temperature reactor concept. • High temperature helium loop: concept, development, mechanism, design and constraints. - Abstract: Rapidly increasing energy and electricity demands, global concerns over the climate changes and strong dependence on foreign fossil fuel supplies are powerfully influencing greater use of nuclear power. In order to establish the viability of next-generation reactor concepts to meet tomorrow's needs for clean and reliable energy production the fundamental research and development issues need to be addressed for the Generation-IV nuclear-energy systems. Generation-IV reactor concepts are being developed to use more advanced materials, coolants and higher burn-ups fuels, while keeping a nuclear reactor safe and reliable. One of the six Generation-IV concepts is a very high temperature reactor (VHTR). The VHTR concept uses a graphite-moderated core with a once-through uranium fuel cycle, using high temperature helium as the coolant. Because helium is naturally inert and single-phase, the helium-cooled reactor can operate at much higher temperatures, leading to higher efficiency. Current VHTR concepts will use fuels such as uranium dioxide, uranium carbide, or uranium oxycarbide. Since some of these fuels are new in nuclear industry and due to their unknown properties and behavior within VHTR conditions it is very important to address these issues by investigate their characteristics within conditions close to those in VHTRs. This research can be performed in a research reactor with in-pile helium loop designed and constructed in Research Center Rez Ltd. One of the topics analyzed in this article are also physical characteristic and benefits of gas

  7. Taguchi Based Regression Analysis of End-Wall Film Cooling in a Gas Turbine Cascade with Single Row of Holes

    Science.gov (United States)

    Ravi, D.; Parammasivam, K. M.

    2016-09-01

    Numerical investigations were conducted on a turbine cascade, with end-wall cooling by a single row of cylindrical holes, inclined at 30°. The mainstream fluid was hot air and the coolant was CO2 gas. Based on the Reynolds number, the flow was turbulent at the inlet. The film hole row position, its pitch and blowing ratio was varied with five different values. Taguchi approach was used in designing a L25 orthogonal array (OA) for these parameters. The end-wall averaged film cooling effectiveness (bar η) was chosen as the quality characteristic. CFD analyses were carried out using Ansys Fluent on computational domains designed with inputs from OA. Experiments were conducted for one chosen OA configuration and the computational results were found to correlate well with experimental measurements. The responses from the CFD analyses were fed to the statistical tool to develop a correlation for bar η using regression analysis.

  8. Experimental investigation of gas turbine airfoil aerodynamic performance without and with film cooling in an annular sector cascade

    Energy Technology Data Exchange (ETDEWEB)

    Wiers, S.H.

    2002-02-01

    The steady growing of industrialization, the densification of the anthroposphere, the increasing concern over the effects of gas turbine cruise emissions on the atmosphere threaten the growth of air transportation, and the perception about the possible climatic impact of CO{sub 2} emissions causes a public distinctive sense of responsibility. The conventional energy production techniques, which are based on fossil fuel, will keep its central importance within the global energy production. Forecasts about the increasing air transportation give duplication in the next 10-15 years. The optimization of the specific fuel consumption is necessary to decrease the running costs and the pollution emissions in the atmosphere, which makes an increased process efficiency of stationary turbines as well as of jet engines essential. This leads to the necessity of an increased thermodynamic efficiency of the overall process and the optimization of the aerodynamic components. Due to the necessity of more detailed three-dimensional data on the behavior of film cooled blades an annular sector cascade turbine test facility has gone into service. The annular sector cascade facility is a relative cost efficient solution compared to a full annular facility to investigate three-dimensional effects on a non cooled and cooled turbine blade. The aerodynamic investigations on the annular sector cascade facility are part of a broad perspective where experimental data from a hot annular sector cascade facility and the cold annular sector facility are used to verify, calibrate and understand the physics for both internal and external calculation methods for flow and heat transfer prediction. The objective of the present study is the design and validation of a cold flow annular sector cascade facility, which meets the flow conditions in a modem turbine as close as possible, with emphasis on achieving periodic flow conditions. The first part of this study gives the necessary background on this

  9. Insights into gas heating and cooling in the disc of NGC 891 from Herschel far-infrared spectroscopy

    CERN Document Server

    Hughes, T M; Schirm, M R P; Parkin, T J; De Looze, I; Wilson, C D; Bendo, G J; Baes, M; Fritz, J; Boselli, A; Cooray, A; Cormier, D; Karczewski, O Ł; Lebouteiller, V; Lu, N; Madden, S C; Spinoglio, L; Viaene, S

    2014-01-01

    We present Herschel PACS and SPIRE spectroscopy of the most important far-infrared cooling lines in the nearby edge-on spiral galaxy, NGC 891: [CII] 158 $\\mu$m, [NII] 122, 205 $\\mu$m, [OI] 63, 145 $\\mu$m, and [OIII] 88 $\\mu$m. We find that the photoelectric heating efficiency of the gas, traced via the ([CII]+[OII]63)/$F_{\\mathrm{TIR}}$ ratio, varies from a mean of 3.5$\\times$10$^{-3}$ in the centre up to 8$\\times$10$^{-3}$ at increasing radial and vertical distances in the disc. A decrease in ([CII]+[OII]63)/$F_{\\mathrm{TIR}}$ but constant ([CII]+[OI]63)/$F_{\\mathrm{PAH}}$ with increasing FIR colour suggests that polycyclic aromatic hydrocarbons (PAHs) may become important for gas heating in the central regions. We compare the observed flux of the FIR cooling lines and total IR emission with the predicted flux from a PDR model to determine the gas density, surface temperature and the strength of the incident far-ultraviolet (FUV) radiation field, $G_{0}$. Resolving details on physical scales of ~0.6 kpc, a p...

  10. Gas infall into atomic cooling haloes: on the formation of protogalactic disks and supermassive black holes at z > 10

    CERN Document Server

    Prieto, Joaquin; Haiman, Zoltan

    2013-01-01

    We have performed cosmo-hydro simulations using the RAMSES code to study atomic cooling (ACHs) haloes at z=10 with masses 5E7Msun10 to date. We examine the morphology, angular momentum (AM), thermodynamic, and turbulence of these haloes, in order to assess the prevalence of disks and supermassive black holes (SMBHs). We find no correlation between either the magnitude or the direction of the AM of the gas and its parent DM halo. Only 3 haloes form rotationally supported cores. Two of the most massive haloes form massive, compact overdense blobs. These blobs have an accretion rate ~0.5 Msun/yr (at a distance of 100 pc), and are possible sites of SMBH formation. Our results suggest that the degree of rotational support and the fate of the gas in a halo is determined by its large-scale environment and merger history. In particular, the two haloes forming blobs are located at knots of the cosmic web, cooled early on, and experienced many mergers. The gas in these haloes is lumpy and highly turbulent, with Mach N....

  11. Study on a method for loading a Li compound to produce tritium using high-temperature gas-cooled reactor

    Energy Technology Data Exchange (ETDEWEB)

    Nakaya, Hiroyuki, E-mail: nakaya@nucl.kyushu-u.ac.jp [Department of Applied Quantum Physics and Nuclear Engineering, Kyushu University, 744 Motooka, Fukuoka 8190395 (Japan); Matsuura, Hideaki [Department of Applied Quantum Physics and Nuclear Engineering, Kyushu University, 744 Motooka, Fukuoka 8190395 (Japan); Katayama, Kazunari [Department of Advanced Energy Engineering Science, Kyushu University, 6-1 Kasuga-koen, Kasuga 8168580 (Japan); Goto, Minoru; Nakagawa, Shigeaki [Japan Atomic Energy Agency, 4002 Oarai, Ibaraki (Japan)

    2015-10-15

    Highlights: • Tritium production by a high-temperature gas-cooled reactor was studied. • The loading method considering tritium outflow suppression was estimated. • A reactor with 600 MWt produced 400–600 g of tritium for 180 days. • A possibility that tritium outflow can be sufficiently suppressed was shown. - Abstract: Tritium production using high-temperature gas-cooled reactors and its outflow from the region loading Li compound into the helium coolant are estimated when considering the suppression of tritium outflow. A Li rod containing a cylindrical Li compound placed in an Al{sub 2}O{sub 3} cladding tube is assumed as a method for loading Li compound. A gas turbine high-temperature reactor of 300 MW electrical nominal capacity (GTHTR300) with 600 MW thermal output power is considered and modeled using the continuous-energy Monte Carlo transport code MVP-BURN, where burn-up simulations are carried out. Tritium outflow is estimated from equilibrium solution for the tritium diffusion equation in the cladding tube. A GTHTR300 can produce 400–600 g of tritium over a 180-day operation using the chosen method of loading the Li compound while minimizing tritium outflow from the cladding tube. Optimizing tritium production while suppressing tritium outflow is discussed.

  12. THE DIRECT DETECTION OF COOL, METAL-ENRICHED GAS ACCRETION ONTO GALAXIES AT z {approx} 0.5

    Energy Technology Data Exchange (ETDEWEB)

    Rubin, Kate H. R.; Xavier Prochaska, J. [Max-Planck-Institut fuer Astronomie, Koenigstuhl 17, 69117 Heidelberg (Germany); Koo, David C. [Department of Astronomy and Astrophysics, UCO/Lick Observatory, University of California, 1156 High St, Santa Cruz, CA 95064 (United States); Phillips, Andrew C., E-mail: rubin@mpia.de [UCO/Lick Observatory, University of California, 1156 High St, Santa Cruz, CA 95064 (United States)

    2012-03-10

    We report on the discovery of cool gas inflow toward six star-forming galaxies with redshifts z {approx} 0.35-1. Analysis of Mg II and Fe II resonance-line absorption in Keck/LRIS spectroscopy of the galaxies reveals positive velocity shifts for cool gas of 80-200 km s{sup -1} with respect to the host galaxy velocity centroids, and equivalent widths for this inflow of {approx}> 0.6 A in five of the six objects. The host galaxies exhibit a wide range of star formation rates (SFRs {approx}1-40 M{sub Sun} yr{sup -1}) and have stellar masses similar to that of the Milky Way (log M{sub *}/M{sub Sun} {approx} 9.6-10.5). Imaging from the Hubble Space Telescope Advanced Camera for Surveys indicates that five of the six galaxies have highly inclined (i > 55 Degree-Sign ), disk-like morphologies. These data represent the first unambiguous detection of inflow into isolated, star-forming galaxies in the distant universe. We suggest that the inflow is due to the infall of enriched material from dwarf satellites and/or a galactic fountain within the galaxies. Assuming that the material has been enriched to 0.1 Z{sub Sun} and has a physical extent approximately equal to that of the galaxies (implied by the high observed gas covering fractions), we infer mass inflow rates of dM{sub in}/dt {approx}> 0.2-3 M{sub Sun} yr{sup -1} for four of these systems. Finally, from comparison of these absorption lines to the profiles of Mg II and Fe II absorption in a larger spectroscopic sample of {approx}100 objects, we measure a covering fraction of cool inflow of at least 6%, but cannot rule out the presence of enriched infall onto as many as {approx}40 of these galaxies.

  13. Noise induces rare events in granular media.

    Science.gov (United States)

    Khain, Evgeniy; Sander, Leonard M

    2016-09-01

    The granular Leidenfrost effect [B. Meerson, et al., Phys. Rev. Lett. 91, 024301 (2003)PRLTAO0031-900710.1103/PhysRevLett.91.024301; P. Eshuis et al., Phys. Rev. Lett. 95, 258001 (2005)PRLTAO0031-900710.1103/PhysRevLett.95.258001] is the levitation of a mass of granular matter when a wall below the grains is vibrated, giving rise to a hot granular gas below the cluster. We find by simulation that for a range of parameters the system is bistable: the levitated cluster can occasionally break and give rise to two clusters and a hot granular gas above and below. We use techniques from the theory of rare events to compute the mean transition time for breaking to occur. This requires the introduction of a two-component reaction coordinate.

  14. Formation of van der Waals molecules in buffer gas cooled magnetic traps

    CERN Document Server

    Brahms, N; Zhang, P; los, J K; Sadeghpour, H R; Dalgarno, A; Doyle, J M; Walker, T G

    2010-01-01

    We show that a large class of helium-containing cold polar molecules form readily in a cryogenic buffer gas, achieving densities as high as 10^12 cm^-3. We explore the spin relaxation of these molecules in buffer gas loaded magnetic traps, and identify a loss mechanism based on Landau-Zener transitions arising from the anisotropic hyperfine interaction. Our results show that the recently observed strong T^6 thermal dependence of spin change in buffer gas trapped silver (Ag) is accounted for by the formation and spin change of AgHe, thus providing evidence for molecular formation in a buffer gas trap.

  15. Signatures of cool gas fueling a star-forming galaxy at redshift 2.3.

    Science.gov (United States)

    Bouché, N; Murphy, M T; Kacprzak, G G; Péroux, C; Contini, T; Martin, C L; Dessauges-Zavadsky, M

    2013-07-05

    Galaxies are thought to be fed by the continuous accretion of intergalactic gas, but direct observational evidence has been elusive. The accreted gas is expected to orbit about the galaxy's halo, delivering not just fuel for star formation but also angular momentum to the galaxy, leading to distinct kinematic signatures. We report observations showing these distinct signatures near a typical distant star-forming galaxy, where the gas is detected using a background quasar passing 26 kiloparsecs from the host. Our observations indicate that gas accretion plays a major role in galaxy growth because the estimated accretion rate is comparable to the star-formation rate.

  16. Mathematical Model of Two Phase Flow in Natural Draft Wet-Cooling Tower Including Flue Gas Injection

    Directory of Open Access Journals (Sweden)

    Hyhlík Tomáš

    2016-01-01

    Full Text Available The previously developed model of natural draft wet-cooling tower flow, heat and mass transfer is extended to be able to take into account the flow of supersaturated moist air. The two phase flow model is based on void fraction of gas phase which is included in the governing equations. Homogeneous equilibrium model, where the two phases are well mixed and have the same velocity, is used. The effect of flue gas injection is included into the developed mathematical model by using source terms in governing equations and by using momentum flux coefficient and kinetic energy flux coefficient. Heat and mass transfer in the fill zone is described by the system of ordinary differential equations, where the mass transfer is represented by measured fill Merkel number and heat transfer is calculated using prescribed Lewis factor.

  17. Spectral narrowing of coherent population trapping resonance in laser-cooled and room-temperature atomic gas

    Indian Academy of Sciences (India)

    S Pradhan; S Mishra; R Behera; N Kawade; A K Das

    2014-02-01

    We have investigated coherent population trapping (CPT) in laser-cooled as well as room-temperature (with and without buffer gas) rubidium atoms. The characteristic broad signal profile emerging from the two-photon Raman resonance for room-temperature atomic vapour is consistent with the theoretical calculation incorporating associated thermal averaging. The spectral width of the dark resonance obtained with cold atoms is found to be broadened, compared to roomtemperature vapour cell, due to the feeble role played by thermal averaging, although the cold atomic sample significantly overcomes the limitation of the transit time broadening. An alternative way to improve transit time is to use a buffer gas, with which we demonstrate that the coherent population trapping signal width is reduced to < 540 Hz.

  18. Advanced Gas-Cooled Nuclear Reactor Materials Evaluation and Development Program. Progress report, July 1, 1979-September 30, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-03-07

    The results of work performed from July 1, 1979 through September 30, 1979 on the Advanced Gas-Cooled Nuclear Reactor Materials Evaluation and Development Program are presented. The objectives of this program are to evaluate candidate alloys for Very High Temperature Reactor (VHTR) Nuclear Process Heat (NPH) and Direct Cycle Helium Turbine (DCHT) applications, in terms of the effect of simulated reactor primary coolant (helium containing small amounts of various other gases), high temperatures, and long time exposures, on the mechanical properties and structural and surface stability of selected candidate alloys. A second objective is to select and recommend materials for future test facilities and more extensive qualification programs. Work covered in this report includes the activities associated with the status of the simulated reactor helium supply system, testing equipment, and gas chemistry analysis instrumentation and equipment. The status of the data management system is presented. In addition, the progress in the screening test program is described.

  19. Advanced Gas Cooled Nuclear Reactor Materials Evaluation and Development Program. Progress report, January 1, 1980-March 31, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-25

    Results are presented of work performed on the Advanced Gas-Cooled Nuclear Reactor Materials Evaluation and Development Program. The objectives of this program are to evaluate candidate alloys for Very High Temperature Reactor (VHTR) Nuclear Process Heat (NPH) and Direct Cycle Helium Turbine (DCHT) applications, in terms of the effect of simulated reactor primary coolant (helium containing small amounts of various other gases), high temperatures, and long time exposures, on the mechanical properties and structural and surface stability of selected candidate alloys. A second objective is to select and recommend materials for future test facilities and more extensive qualification programs. Included are the activities associated with the status of the simulated reactor helium supply system, testing equipment and gas chemistry analysis instrumentation and equipment. The progress in the screening test program is described, including screening creep results and metallographic analysis for materials thermally exposed or tested at 750, 850, and 950/sup 0/C.

  20. Advanced Gas-Cooled Nuclear Reactor Materials Evaluation and Development Program. Progress report, April 1, 1979-June 30, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-25

    The results are presented of work performed on the Advanced Gas-Cooled Nuclear Reactor Materials Evaluation and Development Program. The objectives of this program are to evaluate candidate alloys for Very High Temperature Reactor (VHTR) Nuclear Process Heat (NPH) and Direct Cycle Helium Turbine (DCHT) applications, in terms of the effect of simulated reactor primary coolant (helium containing small amounts of various other gases), high temperatures, and long time exposures, on the mechanical properties and structural and surface stability of selected candidate alloys. A second objective is to select and recommend materials for future test facilities and more extensive qualification programs. Work covered in this report includes the activities associated with the status of the simulated reactor helium supply system, testing equipment, and gas chemistry analysis instrumentation and equipment. The status of the data management system is presented. In addition, the progress in the screening test program is described.

  1. Advanced gas cooled nuclear reactor materials evaluation and development program. Progress report, July 1--September 30, 1978

    Energy Technology Data Exchange (ETDEWEB)

    1978-11-24

    Results of work performed from July 1, 1978 through September 30, 1978 on the Advanced Gas Cooled Nuclear Reactor Materials Evaluation and Development Program are presented. Candidate alloys were evaluated for Very High Temperature Reactor Nuclear Process Heat (NPH) and Direct Cycle Helium Turbine (DCHT) applications, in terms of the affect of simulated reactor primary coolant (Helium containing small amounts of various other gases), the high temperatures, and long time exposures, on the mechanical properties and structural and surface stability of selected candidate alloys. The activities associated with the characterization of the materials for the screening test program are reported, i.e., test specimen preparation, information from the materials characterization tests performed by General Electric, and the status of the simulated reactor helium supply system, testing equipment, and gas chemistry analysis instrumentation and equipment. The status of the data management system is presented.

  2. Numerical Simulation of Three-dimensional Heat and Mass Transfer in Spray Cooling of Converter Gas in a Venturi Scrubber

    Institute of Scientific and Technical Information of China (English)

    LU Tao; WANG Kuisheng

    2009-01-01

    In order to predict the pressure drop, collection efficiency, velocity, temperature and mole fraction of vapor in an industrial venturi scrubber with water spraying for converter gas cooling, a three-dimensional model of heat and mass transfer with phase change is established. The gas flow and liquid droplets are treated as a continuous phase with a Eulerian approach and as a discrete phase with a Lagrangian approach, respectively. The coupled problem of heat, force, and mass transfers between gas flow and liquid droplets is solved by a commercial computational fluid dynamics(CFD) package, FLUENT. The numerical results show that the water injections have an important influence on the distributions of pressure, velocity, temperature, and mole fraction of vapor, especially for the spraying region in the throat. In the spraying region, the pressure drop is higher and the velocity is lower than in other regions due to the gas-droplet drag, while the temperature is lower because the droplet absorbs large amounts of heat from the high temperature gas and the mole fraction of vapor is higher due to the phase change of the liquid droplet. A number of cases with different water-to-gas volume flow ratios and baffle openings were simulated. The dependence of pressure drop, velocity, temperature, mole fraction of vapor, and collection efficiency on both the water-to-gas volume flow ratio and baffle opening are analyzed. The good agreements between simulation results and experiment data of pressure drop, temperature, and collection efficiency validate the model. The model should facilitate optimization of the venturi scrubber design in order to give better performance with lower pressure drops and higher collection efficiency.

  3. Critical Current and Stability of MgB$_2$ Twisted-Pair DC Cable Assembly Cooled by Helium Gas

    CERN Document Server

    AUTHOR|(CDS)2069632; Ballarino, Amalia; Yang, Yifeng; Young, Edward Andrew; Bailey, Wendell; Beduz, Carlo

    2013-01-01

    Long length superconducting cables/bus-bars cooled by cryogenic gases such as helium operating over a wider temperature range are a challenging but exciting technical development prospects, with applications ranging from super-grid transmission to future accelerator systems. With limited existing knowledge and previous experiences, the cryogenic stability and quench protection of such cables are crucial research areas because the heat transfer is reduced and temperature gradient increased compared to liquid cryogen cooled cables. V-I measurements on gas-cooled cables over a significant length are an essential step towards a fully cryogenic stabilized cable with adequate quench protection. Prototype twisted-pair cables using high-temperature superconductor and MgB2 tapes have been under development at CERN within the FP7 EuCARD project. Experimental studies have been carried out on a 5-m-long multiple MgB$_2$ cable assembly at different temperatures between 20 and 30 K. The subcables of the assembly showed sim...

  4. Laser cooling of dense atomic gases by collisional redistribution of radiation and spectroscopy of molecular dimers in a dense buffer gas environment

    CERN Document Server

    Saß, Anne; Christopoulos, Stavros; Knicker, Katharina; Moroshkin, Peter; Weitz, Martin

    2014-01-01

    We study laser cooling of atomic gases by collisional redistribution of fluorescence. In a high pressure buffer gas regime, frequent collisions perturb the energy levels of alkali atoms, which allows for the absorption of a far red detuned irradiated laser beam. Subsequent spontaneous decay occurs close to the unperturbed resonance frequency, leading to a cooling of the dense gas mixture by redistribution of fluorescence. Thermal deflection spectroscopy indicates large relative temperature changes down to and even below room temperature starting from an initial cell temperature near 700 K. We are currently performing a detailed analysis of the temperature distribution in the cell. As we expect this cooling technique to work also for molecular-noble gas mixtures, we also present initial spectroscopic experiments on alkali-dimers in a dense buffer gas surrounding.

  5. Instabilities in granular gas–solid flows

    Science.gov (United States)

    Gómez González, Rubén; Garzó, Vicente

    2017-04-01

    A linear stability analysis of the hydrodynamic equations with respect to the homogeneous cooling state is performed to study the conditions for stability of a suspension of solid particles immersed in a viscous gas. The dissipation in such systems arises from two different sources: inelasticity in particle collisions and viscous friction dissipation due to the influence of the gas phase on the solid particles. The starting point is a suspension model based on the (inelastic) Enskog kinetic equation. The effect of the interstitial gas phase on the dynamics of grains is modeled though a viscous drag force. The study is carried out in two different steps. First, the transport coefficients of the system are obtained by solving the Enskog equation by means of the Chapman–Enskog method up to first order in spatial gradients. Explicit expressions for the Navier–Stokes transport coefficients are obtained in terms of the volume fraction, the coefficient of restitution and the friction coefficient characterizing the amplitude of the external force. Once the transport properties are known, then the corresponding linearized hydrodynamic equations are solved to get the dispersion relations. In contrast to previous studies (Garzó et al 2016 Phys. Rev. E 93 012905), the hydrodynamic modes are analytically obtained as functions of the parameter space of the system. For a d-dimensional system, as expected linear stability shows d  ‑  1 transversal (shear) modes and a longitudinal ‘heat’ mode to be unstable with respect to long enough wavelength excitations. The results also show that the main effect of the gas phase is to decrease the value of the critical length L c (beyond which the system becomes unstable) with respect to its value for a dry granular fluid. Comparison with direct numerical simulations for L c shows a qualitative good agreement for conditions of practical interest.

  6. Preliminary Design Study of Medium Sized Gas Cooled Fast Reactor with Natural Uranium as Fuel Cycle Input

    Science.gov (United States)

    Meriyanti, Su'ud, Zaki; Rijal, K.; Zuhair, Ferhat, A.; Sekimoto, H.

    2010-06-01

    In this study a fesibility design study of medium sized (1000 MWt) gas cooled fast reactors which can utilize natural uranium as fuel cycle input has been conducted. Gas Cooled Fast Reactor (GFR) is among six types of Generation IV Nuclear Power Plants. GFR with its hard neuron spectrum is superior for closed fuel cycle, and its ability to be operated in high temperature (850° C) makes various options of utilizations become possible. To obtain the capability of consuming natural uranium as fuel cycle input, modified CANDLE burn-up scheme[1-6] is adopted this GFR system by dividing the core into 10 parts of equal volume axially. Due to the limitation of thermal hydraulic aspects, the average power density of the proposed design is selected about 70 W/cc. As an optimization results, a design of 1000 MWt reactors which can be operated 10 years without refueling and fuel shuffling and just need natural uranium as fuel cycle input is discussed. The average discharge burn-up is about 280 GWd/ton HM. Enough margin for criticallity was obtained for this reactor.

  7. Quantifying non-ergodic dynamics of force-free granular gases.

    Science.gov (United States)

    Bodrova, Anna; Chechkin, Aleksei V; Cherstvy, Andrey G; Metzler, Ralf

    2015-09-14

    Brownian motion is ergodic in the Boltzmann-Khinchin sense that long time averages of physical observables such as the mean squared displacement provide the same information as the corresponding ensemble average, even at out-of-equilibrium conditions. This property is the fundamental prerequisite for single particle tracking and its analysis in simple liquids. We study analytically and by event-driven molecular dynamics simulations the dynamics of force-free cooling granular gases and reveal a violation of ergodicity in this Boltzmann-Khinchin sense as well as distinct ageing of the system. Such granular gases comprise materials such as dilute gases of stones, sand, various types of powders, or large molecules, and their mixtures are ubiquitous in Nature and technology, in particular in Space. We treat-depending on the physical-chemical properties of the inter-particle interaction upon their pair collisions-both a constant and a velocity-dependent (viscoelastic) restitution coefficient ε. Moreover we compare the granular gas dynamics with an effective single particle stochastic model based on an underdamped Langevin equation with time dependent diffusivity. We find that both models share the same behaviour of the ensemble mean squared displacement (MSD) and the velocity correlations in the limit of weak dissipation. Qualitatively, the reported non-ergodic behaviour is generic for granular gases with any realistic dependence of ε on the impact velocity of particles.

  8. Enormous disc of cool gas surrounding the nearby powerful radio galaxy NGC 612 (PKS 0131-36)

    CERN Document Server

    Emonts, B H C; Oosterloo, T A; Holt, J; Tadhunter, C N; Van der Hulst, J M; Ojha, R; Sadler, E M

    2008-01-01

    We present the detection of an enormous disc of cool neutral hydrogen (HI) gas surrounding the S0 galaxy NGC 612, which hosts one of the nearest powerful radio sources (PKS 0131-36). Using the Australia Telescope Compact Array, we detect M_HI = 1.8 x 10^9 M_sun of HI emission-line gas that is distributed in a 140 kpc wide disc-like structure along the optical disc and dust-lane of NGC 612. The bulk of the gas in the disc appears to be settled in regular rotation with a total velocity range of 850 km/s, although asymmetries in this disc indicate that perturbations are being exerted on part of the gas, possibly by a number of nearby companions. The HI disc in NGC 612 suggests that the total mass enclosed by the system is M_enc ~ 2.9 x 10^12 sin^-2(i) M_sun, implying that this early-type galaxy contains a massive dark matter halo. We also discuss an earlier study by Holt et al. that revealed the presence of a prominent young stellar population at various locations throughout the disc of NGC 612, indicating that ...

  9. A Preliminary Investigation of Exhaust-Gas Ejectors for Ground Cooling

    Science.gov (United States)

    1942-07-01

    experimental inveetigationa of the ejector principle have been made in the past in connection with aircraft problems. References 2, and 3 present resulte...made to determine the efficacy of ’ ejectors actuated by the exhaust of an aircraft engine in providing engine cooling air at the ground condition...of total-presuure drop APt with engine hxxepower i’or .: arbus lengths oi the e j ec to r s af 4-inch diameter i o ahown in :igure 4 (a

  10. A SUBSTANTIAL MASS OF COOL, METAL-ENRICHED GAS SURROUNDING THE PROGENITORS OF MODERN-DAY ELLIPTICALS

    Energy Technology Data Exchange (ETDEWEB)

    Prochaska, J. Xavier [Department of Astronomy and Astrophysics, UCO/Lick Observatory, University of California, 1156 High Street, Santa Cruz, CA 95064 (United States); Hennawi, Joseph F. [Max-Planck-Institut fuer Astronomie, Koenigstuhl 17, D-69115 Heidelberg (Germany); Simcoe, Robert A. [MIT-Kavli Institute for Astrophysics and Space Research, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States)

    2013-01-10

    The hosts of luminous z {approx} 2 quasars evolve into today's massive elliptical galaxies. Current theories predict that the circumgalactic medium (CGM) of these massive, dark matter halos (M{sub DM} {approx} 10{sup 12.5} M{sub Sun }) should be dominated by a T {approx} 10{sup 7} K virialized plasma. We test this hypothesis with observations of 74 close-projected quasar pairs, using spectra of the background QSO to characterize the CGM of the foreground one. Surprisingly, our measurements reveal a cool (T Almost-Equal-To 10{sup 4} K), massive (M{sub CGM} > 10{sup 10} M{sub Sun }), and metal-enriched (Z {approx}> 0.1 Z{sub Sun }) medium extending to at least the expected virial radius (r{sub vir} = 160 kpc). The average equivalent widths of H I Ly{alpha} (W-bar{sub Ly{alpha}}= 2.1{+-}0.15 A for impact parameters R < 200 kpc) and C II 1334 (W-bar{sub 1334}= 0.7{+-}0.1) exceed the corresponding CGM measurements of these transitions from all galaxy populations studied previously. Furthermore, we conservatively estimate that the quasar CGM has a 64{sup +6}{sub -7}% covering fraction of optically thick gas (N{sub HI} > 10{sup 17.2} cm{sup -2}) within r{sub vir}; this covering factor is twice that of the contemporaneous Lyman break galaxy population. This unexpected reservoir of cool gas is rarely detected 'down-the-barrel' to quasars, and hence it is likely that our background sight lines intercept gas that is shadowed from the quasar ionizing radiation by the same obscuring medium often invoked in models of active galactic nucleus unification. Because the high-z halos inhabited by quasars predate modern groups and clusters, these observations are also relevant to the formation and enrichment history of the intragroup/intracluster medium.

  11. The Effect of Protoplanetary Disk Cooling Times on the Formation of Gas Giant Planets by Gravitational Instability

    Science.gov (United States)

    Boss, Alan P.

    2017-02-01

    Observational evidence exists for the formation of gas giant planets on wide orbits around young stars by disk gravitational instability, but the roles of disk instability and core accretion for forming gas giants on shorter period orbits are less clear. The controversy extends to population synthesis models of exoplanet demographics and to hydrodynamical models of the fragmentation process. The latter refers largely to the handling of radiative transfer in three-dimensional (3D) hydrodynamical models, which controls heating and cooling processes in gravitationally unstable disks, and hence dense clump formation. A suite of models using the β cooling approximation is presented here. The initial disks have masses of 0.091 M ⊙ and extend from 4 to 20 au around a 1 M ⊙ protostar. The initial minimum Toomre Q i values range from 1.3 to 2.7, while β ranges from 1 to 100. We show that the choice of Q i is equal in importance to the β value assumed: high Q i disks can be stable for small β, when the initial disk temperature is taken as a lower bound, while low Q i disks can fragment for high β. These results imply that the evolution of disks toward low Q i must be taken into account in assessing disk fragmentation possibilities, at least in the inner disk, i.e., inside about 20 au. The models suggest that if low Q i disks can form, there should be an as yet largely undetected population of gas giants orbiting G dwarfs between about 6 au and 16 au.

  12. Geothermal Energy Production from Oil/Gas Wells and Application for Building Cooling

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Honggang [Rutgers University; Liu, Xiaobing [ORNL

    2016-01-01

    One significant source of low-temperature geothermal energy is the coproduced hot water from oil/gas field production. In the United States, daily oil production has reached above 8 million barrels in recent years. Considering various conditions of wells, 5-10 times or more water can be coproduced in the range of temperature 120 F to 300 F. Like other geothermal resources, such energy source from oil/gas wells is under-utilized for its typical long distance from consumption sites. Many oil/gas fields, however, are relatively close (less than 10 miles) to consumers around cities. For instance, some petroleum fields in Pennsylvania are only a few miles away from the towns in Pittsburg area and some fields in Texas are quite close to Houston. In this paper, we evaluate geothermal potential from oil/gas wells by conducting numerical simulation and analysis of a fractured oil well in Hastings West field, Texas. The results suggest that hot water can be continuously coproduced from oil wells at a sufficient rate (about 4000 gallons/day from one well) for more than 100 years. Viable use of such geothermal source requires economical transportation of energy to consumers. The recently proposed two-step geothermal absorption (TSGA) system provides a promising energy transport technology that allows large-scale use of geothermal energy from thousands of oil/gas wells.

  13. A review of existing gas-cooled reactor circulators with application of the lessons learned to the new production reactor circulators

    Energy Technology Data Exchange (ETDEWEB)

    White, L.S.

    1990-07-01

    This report presents the results of a study of the lessons learned during the design, testing, and operation of gas-cooled reactor coolant circulators. The intent of this study is to identify failure modes and problem areas of the existing circulators so this information can be incorporated into the design of the circulators for the New Production Reactor (NPR)-Modular High-Temperature Gas Cooled Reactor (MHTGR). The information for this study was obtained primarily from open literature and includes data on high-pressure, high-temperature helium test loop circulators as well as the existing gas cooled reactors worldwide. This investigation indicates that trouble free circulator performance can only be expected when the design program includes a comprehensive prototypical test program, with the results of this test program factored into the final circulator design. 43 refs., 7 tabs.

  14. Formation of van der Waals molecules in buffer-gas-cooled magnetic traps [corrected].

    Science.gov (United States)

    Brahms, N; Tscherbul, T V; Zhang, P; Kłos, J; Sadeghpour, H R; Dalgarno, A; Doyle, J M; Walker, T G

    2010-07-16

    We predict that a large class of helium-containing cold polar molecules form readily in a cryogenic buffer gas, achieving densities as high as 10(12)  cm(-3). We explore the spin relaxation of these molecules in buffer-gas-loaded magnetic traps and identify a loss mechanism based on Landau-Zener transitions arising from the anisotropic hyperfine interaction. Our results show that the recently observed strong T(-6) thermal dependence of the spin-change rate of silver (Ag) trapped in dense (3)He is accounted for by the formation and spin change of Ag(3)He van der Waals molecules, thus providing indirect evidence for molecular formation in a buffer-gas trap.

  15. World exclusive . . Snoehvit plays it cool[Liquefied natural gas technology

    Energy Technology Data Exchange (ETDEWEB)

    Knott, T.

    2002-04-01

    This article reports on the planned recovery of the natural gas reserves from three large offshore gas fields - known collectively as Snoehvit - in the Barents Sea. Details are given of the location of the fields, the aim of operator Statoil and its co-venturers to transport the natural gas through a multiphase pipeline to a LNG plant on an island near Hammerfest, and the strong support of the Norwegian government. Statoil's strategy of phased development of the Askeladd, Albatross and Snoehvit fields starting with the Snoehvit field is discussed along with pipelines, the LNG plant, the drilling of the production wells, and pipeline design. The carbon dioxide injection pipeline, control systems, onshore technology, and environmental and economic issues are considered.

  16. Development of an evaluation method of fission product release fraction from High Temperature Gas-cooled Reactor fuel

    Energy Technology Data Exchange (ETDEWEB)

    Sawa, Kazuhiro; Minato, Kazuo; Fukuda, Kousaku [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1996-11-01

    The High Temperature Gas-cooled Reactor (HTGR) uses coated particles as fuel. Current coated particle is a microsphere of fuel kernel with TRISO coatings. The TRISO coatings consist of a low-density, porous pyrolytic carbon (PyC) buffer layer adjacent to the spherical fuel kernel, followed by an inner isotropic PyC layer, a SiC layer and a final (outer) PyC layer. An evaluation method of fission product release behavior during the normal operation was developed. Key issues of fission gas release model were: (1) fission gas releases from matrix contamination uranium and through-coatings failed particle were separately modeled and (2) burnup and fast neutron irradiation effects were newly considered. For metallic fission product, fractional release of cesium from coated fuel particles was investigated by comparing measured data in an irradiation test which contained three kinds of fuel particles; artificially bored particles simulating through-coatings failed particles, as-manufactured SiC-failed particles and intact particles. Through the comparison of measured and calculated fractional releases, an equivalent diffusion coefficient of SiC layer in the SiC-failed particle was introduced. This report describes the developed model together with validation result of the release model. (author)

  17. Field monitoring and evaluation of a residential gas-engine-driven heat pump: Volume 1, Cooling season

    Energy Technology Data Exchange (ETDEWEB)

    Miller, J.D.

    1995-09-01

    The Federal government is the largest single energy consumer in the United States; consumption approaches 1.5 quads/year of energy (1 quad = 10{sup 15} Btu) at a cost valued at nearly $10 billion annually. The US Department of Energy (DOE) Federal Energy Management Program (FEMP) supports efforts to reduce energy use and associated expenses in the Federal sector. One such effort, the New Technology Demonstration Program (NTDP), seeks to evaluate new energy-saving US technologies and secure their more timely adoption by the US government. Pacific Northwest Laboratory (PNL)is one of four DOE national multiprogram laboratories that participate in the NTDP by providing technical expertise and equipment to evaluate new, energy-saving technologies being studied and evaluated under that program. This two-volume report describes a field evaluation that PNL conducted for DOE/FEMP and the US Department of Defense (DoD) Strategic Environmental Research and Development Program (SERDP) to examine the performance of a candidate energy-saving technology -- a gas-engine-driven heat pump. The unit was installed at a single residence at Fort Sam Houston, a US Army base in San Antonio, Texas, and the performance was monitored under the NTDP. Participating in this effort under a Cooperative Research and Development Agreement (CRADA) were York International, the heat pump manufacturer, Gas Research Institute (GRI), the technology developer; City Public Service of San Antonio, the local utility; American Gas Cooling Center (AGCC); Fort Sam Houston; and PNL.

  18. Soil greenhouse gas emissions reduce the contribution of mangrove plants to the atmospheric cooling effect

    Science.gov (United States)

    Chen, Guangcheng; Chen, Bin; Yu, Dan; Tam, Nora F. Y.; Ye, Yong; Chen, Shunyang

    2016-12-01

    Mangrove soils have been recognized as sources of greenhouse gases, but the atmospheric fluxes are poorly characterized, and their adverse warming effect has rarely been considered with respect to the potential contribution of mangrove wetlands to climate change mitigation. The current study balanced the warming effect of soil greenhouse gas emissions with the plant carbon dioxide (CO2) sequestration rate derived from the plants’ net primary production in a productive mangrove wetland in South China to assess the role of mangrove wetlands in reducing the atmospheric warming effect. Soil characteristics were also studied in the summer to examine their relationships with gas fluxes. The soil to atmosphere fluxes of nitrous oxide (N2O), methane (CH4) and CO2 ranged from -1.6 to 50.0 μg m-2 h-1, from -1.4 to 5360.1 μg m-2 h-1 and from -31 to 512 mg m-2 h-1, respectively, which indicated that the mangrove soils act as sources of greenhouse gases in this area. The gas fluxes were higher in summer than in the cold seasons and were variable across mangrove sites. Gas fluxes in summer were positively correlated with the soil organic carbon, total nitrogen, and ammonia contents. The mangrove plants sequestered a considerable amount of atmospheric CO2 at rates varying from 3652 to 7420 g CO2 m-2 yr-1. The ecosystem acted as a source of CH4 and N2O gases but was a more intense CO2 sink. However, the warming effect of soil gas emissions accounted for 9.3-32.7% of the plant CO2 sequestration rate, partially reducing the benefit of mangrove plants, and the two trace gases comprised 9.7-33.2% of the total warming effect. We therefore propose that an assessment of the reduction of atmospheric warming effects by a mangrove ecosystem should consider both soil greenhouse gas emissions and plant CO2 sequestration.

  19. A Computational Study for the Utilization of Jet Pulsations in Gas Turbine Film Cooling and Flow Control

    Science.gov (United States)

    Kartuzova, Olga V.

    2012-01-01

    This report is the second part of a three-part final report of research performed under an NRA cooperative Agreement contract. The first part is NASA/CR-2012-217415. The third part is NASA/CR-2012-217417. Jets have been utilized in various turbomachinery applications in order to improve gas turbines performance. Jet pulsation is a promising technique because of the reduction in the amount of air removed from compressor. In this work two areas of pulsed jets applications were computationally investigated using the commercial code Fluent (ANSYS, Inc.); the first one is film cooling of High Pressure Turbine (HPT) blades and second one is flow separation control over Low Pressure Turbine (LPT) airfoil using Vortex Generator Jets (VGJ). Using pulsed jets for film cooling purposes can help to improve the effectiveness and thus allow higher turbine inlet temperature. Effects of the film hole geometry, blowing ratio and density ratio of the jet, pulsation frequency and duty cycle of blowing on the film cooling effectiveness were investigated. As for the low-pressure turbine (LPT) stages, the boundary layer separation on the suction side of airfoils can occur due to strong adverse pressure gradients. The problem is exacerbated as airfoil loading is increased. Active flow control could provide a means for minimizing separation under conditions where it is most severe (low Reynolds number), without causing additional losses under other conditions (high Reynolds number). The effects of the jet geometry, blowing ratio, density ratio, pulsation frequency and duty cycle on the size of the separated region were examined in this work. The results from Reynolds Averaged Navier-Stokes and Large Eddy Simulation computational approaches were compared with the experimental data.

  20. THE DIFFERENT EVOLUTION OF GAS AND DUST IN DISKS AROUND SUN-LIKE AND COOL STARS

    NARCIS (Netherlands)

    Pascucci, I.; Apai, D.; Luhman, K.; Henning, Th.; Bouwman, J.; Meyer, M. R.; Lahuis, F.; Natta, A.

    2009-01-01

    Planet formation is profoundly impacted by the properties of protoplanetary disks and their central star. However, how disk properties vary with stellar parameters remains poorly known. Here, we present the first comprehensive, comparative Spitzer/IRS study of the dust and gas properties of disks ar

  1. Design Study of Modular Nuclear Power Plant with Small Long Life Gas Cooled Fast Reactors Utilizing MOX Fuel

    Science.gov (United States)

    Ilham, Muhammad; Su’ud, Zaki

    2017-01-01

    Growing energy needed due to increasing of the world’s population encourages development of technology and science of nuclear power plant in its safety and security. In this research, it will be explained about design study of modular fast reactor with helium gas cooling (GCFR) small long life reactor, which can be operated over 20 years. It had been conducted about neutronic design GCFR with Mixed Oxide (UO2-PuO2) fuel in range of 100-200 MWth NPPs of power and 50-60% of fuel fraction variation with cylindrical pin cell and cylindrical balance of reactor core geometry. Calculation method used SRAC-CITATION code. The obtained results are the effective multiplication factor and density value of core reactor power (with geometry optimalization) to obtain optimum design core reactor power, whereas the obtained of optimum core reactor power is 200 MWth with 55% of fuel fraction and 9-13% of percentages.

  2. Analysis on thermophoretic deposit of fine particle on water wall of 10 MW high temperature gas-cooled reactor

    Institute of Scientific and Technical Information of China (English)

    ZHOU Tao; YANG Rui-Chang; JIA Dou-Nan

    2005-01-01

    The water wall is an important part of the passive natural circulation residual heat removal system in a high temperature gas-cooled reactor. The maximum temperatures of the pressure shell and the water wall are calculated using annular vertical closed cavity model. Fine particles can deposit on the water wall due to the thermophore sis effect. This deposit can affect heat transfer. The thermophoretic deposit efficiency is calculated by using Batch and Shen's formula fitted for both laminar flow and turbulent flow. The calculated results indicate that natural convection is turbulent in the closed cavity. The transient thermophoretic deposit efficiency rises with the increase of the pressure shell's temperature. Its maximum value is 14%.

  3. Modelling 3D crack propagation in ageing graphite bricks of Advanced Gas-cooled Reactor power plant

    Directory of Open Access Journals (Sweden)

    Thi-Tuyet-Giang Vo

    2015-10-01

    Full Text Available In this paper, crack propagation in Advanced Gas-cooled Reactor (AGR graphite bricks with ageing properties is studied using the eXtended Finite Element Method (X-FEM. A parametric study for crack propagation, including the influence of different initial crack shapes and propagation criteria, is conducted. The results obtained in the benchmark study show that the crack paths from X-FEM are similar to the experimental ones. The accuracy of the strain energy release rate computation in a heterogeneous material is also evaluated using a finite difference approach. Planar and non-planar 3D crack growth simulations are presented to demonstrate the robustness and the versatility of the method utilized. Finally, this work contributes to the better understanding of crack propagation behaviour in AGR graphite bricks and so contributes to the extension of the AGR plants’ lifetimes in the UK by reducing uncertainties.

  4. Entropy generation in a channel resembling gas turbine cooling passage: Effect of rotation number and density ratio on entropy generation

    Indian Academy of Sciences (India)

    M Basha; M Al-Qahtani; B S Yilbas

    2009-06-01

    Flow into a passage resembling a gas turbine blade cooling passage is considered and entropy generation rate in the passage is examined for unique rotation number and density ratios. In the simulations, leading and trailing walls of the passage are assumed to be at constant temperature. A control volume approach is introduced to discretize the governing equations of flow, heat transfer, and entropy generation. Reynolds stress turbulence model is accommodated in the simulation to account for the turbulence. The study is extended to include two rotational speeds and three density ratios. The passage aspect ratio is kept 10:1. It is found that volumetric entropy generation rate attains high values at passage inlet due to attainment of high temperature gradient in this region. Increasing rotation number and density ratio enhances volumetric entropy generation rate in the passage.

  5. Studies on disintegrating spherical fuel elements of high temperature gas-cooled reactor by a electrochemical method

    Science.gov (United States)

    Tian, Lifang; Wen, Mingfen; Chen, Jing

    2013-01-01

    Spherical fuel elements of a high temperature gas-cooled reactor were disintegrated through a electrochemical method with NaNO3 as electrolyte. The X-ray diffraction spectra and total carbon contents of the graphite fragments were determined, and the results agreed with those from simulated fuel elements. After conducting the characterization analysis and the leaching experiment of coated fuel particles, the uranium concentrations of leaching solutions and spent electrolyte were found to be at background levels. The results demonstrate the effectiveness of the improved electrochemical method with NaNO3 as electrolyte in disintegrating the unirradiated fuel elements without any damage to the coated fuel particles. Moreover, the method avoided unexpected radioactivity contamination to the graphite matrix and spent electrolyte.

  6. Analysis of two-phase flow instability in helical tube steam generator in high temperature gas cooled reactor

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Yu; Lv, Xuefeng; Wang, Shengfei; Niu, Fenglei; Tian, Li [North China Electric Power Univ., Beijing (Switzerland)

    2012-03-15

    The steam generator composed of multi-helical tubes is used in high temperature gas cooled reactors and two-phase flow instability should be avoided in design. And density-wave oscillation which is mainly due to flow, density and the relationship between the pressure drop delays and feedback effects is one of the two-phase flow instability phenomena easily to occur. Here drift-flux model is used to simulate the performance of the fluid in the secondary side and frequency domain and time domain methods are used to evaluate whether the density-wave oscillation will happen or not. Several operating conditions with nominal power from 15% to 30% are calculated in this paper. The results of the two methods are in accordance, flow instability will occur when power is less than 20% nominal power, which is also according with the result of the experiments well.

  7. Safety assessment for electricity generation failure accident of gas cooled nuclear power plant using system dynamics (SD) method

    Energy Technology Data Exchange (ETDEWEB)

    Woo, Tae Ho [Seoul National Univ. (Korea, Republic of). Dept. of Nuclear Engineering

    2013-04-15

    The power production failure happens in the loss of coolant of the nuclear power plants (NPPs). The air ingress is a serious accident in gas cooled NPPs. The quantification of the study performed by the system dynamics (SD) method which is processed by the feedback algorithms. The Vensim software package is used for the simulation, which is performed by the Monte-Carlo method. Two kinds of considerations as the economic and safety properties are important in NPPs. The result shows the stability of the operation when the power can be decided. The maximum value of risk is the 11.77 in 43rd and the minimum value is 0.0 in several years. So, the success of the circulation of coolant is simulated by the dynamical values. (orig.)

  8. CFD Analysis of Turbulent Flow Phenomena in the Lower Plenum of a Prismatic Gas-Cooled Reactor

    Energy Technology Data Exchange (ETDEWEB)

    T. Gallaway; S.P. Antal; M.Z. Podowski; D.P. Guillen

    2007-09-01

    This paper is concerned with the implementation of a computational model of turbulent flow in a section of the lower plenum of Very High Temperature Reactor (VHTR). The proposed model has been encoded in a state-of-the-art CFD code, NPHASE. The results of NPHASE predictions have been compared against the experimental data collected using a scaled model of a sub-region in the lower plenum of a modular prismatic gas-cooled reactor. It has been shown that the NPHASE-based model is capable of predicting a three-dimensional velocity field in a complex geometrical configuration of VHTR lower plenum. The current and future validations of computational predictions are necessary for design and analysis of new reactor concepts, as well as for safety analysis and licensing calculations.

  9. Advanced gas cooled nuclear reactor materials evaluation and development program. Progress report, September 23, 1976--December 31, 1976

    Energy Technology Data Exchange (ETDEWEB)

    1977-01-01

    This report presents the results of work performed from September 23, 1976 through December 31, 1976 on the Advanced Gas Cooled Nuclear Reactor Materials Evaluation and Development Program. The objectives of this program are to evaluate candidate alloys for Very High Temperature Reactor (VHTR) Process Heat and Direct Cycle Helium Turbine (DCHT) applications, in terms of the affect of simulated reactor primary coolant (impure Helium), high temperatures, and long time exposures, on the mechanical properties and structural and surface stability of selected candidate alloys. A second objective is to select and recommend materials for future test facilities and more extensive qualification programs. Work covered in this report includes progress to date on alloy selection for VHTR Nuclear Process Heat (NPH) applications and for DCHT applications. The present status on the simulated reactor helium loop design and on designs for the testing and analysis facilities and equipment is discussed.

  10. Application of Simulated Reactivity Feedback in Nonnuclear Testing of a Direct-Drive Gas-Cooled Reactor

    Science.gov (United States)

    Bragg-Sitton, S. M.; Webster, K. L.

    2007-01-01

    Nonnuclear testing can be a valuable tool in the development of an in-space nuclear power or propulsion system. In a nonnuclear test facility, electric heaters are used to simulate heat from nuclear fuel. Standard testing allows one to fully assess thermal, heat transfer, and stress related attributes of a given system but fails to demonstrate the dynamic response that would be present in an integrated, fueled reactor system. The integration of thermal hydraulic hardware tests with simulated neutronic response provides a bridge between electrically heated testing and full nuclear testing. By implementing a neutronic response model to simulate the dynamic response that would be expected in a fueled reactor system, one can better understand system integration issues, characterize integrated system response times and response and response characteristics, and assess potential design improvements with a relatively small fiscal investment. Initial system dynamic response testing was demonstrated on the integrated SAFE 100a heat pipe cooled, electrically heated reactor and heat exchanger hardware. This Technical Memorandum discusses the status of the planned dynamic test methodology for implementation in the direct-drive gas-cooled reactor testing and assesses the additional instrumentation needed to implement high-fidelity dynamic testing.

  11. Design Study of 200MWth Gas Cooled Fast Reactor with Nitride (UN-PuN Fuel Long Life without Refueling

    Directory of Open Access Journals (Sweden)

    Syarifah Ratna Dewi

    2016-01-01

    Full Text Available Design study of 200 MWth Gas Cooled Fast Reactor with UN-PuN fuel long life without refueling has been done. GFR is one type reactor in Generation IV reactor system. It uses helium coolant and fast neutron spectrum. Helium is chemical inert, single phase and low neutron moderation. In this study the calculations are performed by using SRAC code with PIJ calculation for the fuel pin cell calculation and CITATION calculation for core calculation. The data libraries use JENDL 3.2. The variation fuel fractions are 50% until 60%. The diameter active core is 150 cm and the height active core is 100 cm. The reflector radial-axial width is 50 cm. The variation of the powers are 100 MWth up to 500 MWth. The high power causes the high k-eff value. The optimum design is reached when the power is 200 MWth, variation percentage Plutonium for fuel F1:F2:F3=9%:11%:13%. The comparation of fuel:cladding:coolant fraction = 55%:10%:35%. The cooling down time of Plutonium is nine months. The optimum k-eff value is 1.0142 with excess reactivity value 1.403%. The decay of Plutonium decrease k-eff value in the beginning of burn up.

  12. A Techno-Economic Assessment of Hybrid Cooling Systems for Coal- and Natural-Gas-Fired Power Plants with and without Carbon Capture and Storage.

    Science.gov (United States)

    Zhai, Haibo; Rubin, Edward S

    2016-04-05

    Advanced cooling systems can be deployed to enhance the resilience of thermoelectric power generation systems. This study developed and applied a new power plant modeling option for a hybrid cooling system at coal- or natural-gas-fired power plants with and without amine-based carbon capture and storage (CCS) systems. The results of the plant-level analyses show that the performance and cost of hybrid cooling systems are affected by a range of environmental, technical, and economic parameters. In general, when hot periods last the entire summer, the wet unit of a hybrid cooling system needs to share about 30% of the total plant cooling load in order to minimize the overall system cost. CCS deployment can lead to a significant increase in the water use of hybrid cooling systems, depending on the level of CO2 capture. Compared to wet cooling systems, widespread applications of hybrid cooling systems can substantially reduce water use in the electric power sector with only a moderate increase in the plant-level cost of electricity generation.

  13. Development of Safety Analysis Codes and Experimental Validation for a Very High Temperature Gas-Cooled Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Chang, H. Oh, PhD; Cliff Davis; Richard Moore

    2004-11-01

    The very high temperature gas-cooled reactors (VHTGRs) are those concepts that have average coolant temperatures above 900 degrees C or operational fuel temperatures above 1250 degrees C. These concepts provide the potential for increased energy conversion efficiency and for high-temperature process heat application in addition to power generation and nuclear hydrogen generation. While all the High Temperature Gas Cooled Reactor (HTGR) concepts have sufficiently high temperatures to support process heat applications, such as desalination and cogeneration, the VHTGR's higher temperatures are suitable for particular applications such as thermochemical hydrogen production. However, the high temperature operation can be detrimental to safety following a loss-of-coolant accident (LOCA) initiated by pipe breaks caused by seismic or other events. Following the loss of coolant through the break and coolant depressurization, air from the containment will enter the core by molecular diffusion and ultimately by natural convection, leading to oxidation of the in-core graphite structures and fuel. The oxidation will release heat and accelerate the heatup of the reactor core. Thus, without any effective countermeasures, a pipe break may lead to significant fuel damage and fission product release. The Idaho National Engineering and Environmental Laboratory (INEEL) has investigated this event for the past three years for the HTGR. However, the computer codes used, and in fact none of the world's computer codes, have been sufficiently developed and validated to reliably predict this event. New code development, improvement of the existing codes, and experimental validation are imperative to narrow the uncertaninty in the predictions of this type of accident. The objectives of this Korean/United States collaboration are to develop advanced computational methods for VHTGR safety analysis codes and to validate these computer codes.

  14. Development of safety analysis codes and experimental validation for a very high temperature gas-cooled reactor Final report

    Energy Technology Data Exchange (ETDEWEB)

    Chang Oh

    2006-03-01

    The very high-temperature gas-cooled reactor (VHTR) is envisioned as a single- or dual-purpose reactor for electricity and hydrogen generation. The concept has average coolant temperatures above 9000C and operational fuel temperatures above 12500C. The concept provides the potential for increased energy conversion efficiency and for high-temperature process heat application in addition to power generation. While all the High Temperature Gas Cooled Reactor (HTGR) concepts have sufficiently high temperature to support process heat applications, such as coal gasification, desalination or cogenerative processes, the VHTR’s higher temperatures allow broader applications, including thermochemical hydrogen production. However, the very high temperatures of this reactor concept can be detrimental to safety if a loss-of-coolant accident (LOCA) occurs. Following the loss of coolant through the break and coolant depressurization, air will enter the core through the break by molecular diffusion and ultimately by natural convection, leading to oxidation of the in-core graphite structure and fuel. The oxidation will accelerate heatup of the reactor core and the release of toxic gasses (CO and CO2) and fission products. Thus, without any effective countermeasures, a pipe break may lead to significant fuel damage and fission product release. Prior to the start of this Korean/United States collaboration, no computer codes were available that had been sufficiently developed and validated to reliably simulate a LOCA in the VHTR. Therefore, we have worked for the past three years on developing and validating advanced computational methods for simulating LOCAs in a VHTR. Research Objectives As described above, a pipe break may lead to significant fuel damage and fission product release in the VHTR. The objectives of this Korean/United States collaboration were to develop and validate advanced computational methods for VHTR safety analysis. The methods that have been developed are now

  15. Neutron flux measurements in the side-core region of Hunterston B advanced gas-cooled reactor

    Energy Technology Data Exchange (ETDEWEB)

    Allen, D.A. [Serco, Rutherford House, Quedgeley, Gloucester, GL2 4NF (United Kingdom); Shaw, S.E. [British Energy, Barnett Way, Barnwood, Gloucester, GL4 3RS (United Kingdom); Huggon, A.P.; Steadman, R.J.; Thornton, D.A. [Serco, Rutherford House, Quedgeley, Gloucester, GL2 4NF (United Kingdom); Whiley, G.S. [British Energy, Barnett Way, Barnwood, Gloucester, GL4 3RS (United Kingdom)

    2011-07-01

    The core restraints of advanced gas-cooled reactors are important structural components that are required to maintain the geometric integrity of the cores. A review of neutron dosimetry for the sister stations Hunterston B and Hinkley Point B identified that earlier conservative assessments predicted high thermal neutron dose rates to key components of the restraint structure (the restraint rod welds), with the implication that some of them may be predicted to fail during a seismic event. A revised assessment was therefore undertaken [Thornton, D. A., Allen, D. A., Tyrrell, R. J., Meese, T. C., Huggon, A.P., Whiley, G. S., and Mossop, J. R., 'A Dosimetry Assessment for the Core Restraint of an Advanced Gas Cooled Reactor,' Proceedings of the 13. International Symposium on Reactor Dosimetry (ISRD-13, May 2008), World Scientific, River Edge, NJ, 2009, W. Voorbraak, L. Debarberis, and P. D'hondt, Eds., pp. 679-687] using a detailed 3D model and a Monte Carlo radiation transport program, MCBEND. This reassessment resulted in more realistic fast and thermal neutron dose recommendations, the latter in particular being much lower than had been thought previously. It is now desirable to improve confidence in these predictions by providing direct validation of the MCBEND model through the use of neutron flux measurements. This paper describes the programme of work being undertaken to deploy two neutron flux measurement 'stringers' within the side-core region of one of the Hunterston B reactors for the purpose of validating the MCBEND model. The design of the stringers and the determination of the preferred deployment locations have been informed by the use of detailed MCBEND flux calculations. These computational studies represent a rare opportunity to design a flux measurement beforehand, with the clear intention of minimising the anticipated uncertainties and obtaining measurements that are known to be representative of the neutron fields to which

  16. Army Gas-Cooled Reactor Systems program: alternator final design report

    Energy Technology Data Exchange (ETDEWEB)

    1964-06-01

    The development and testing of a demonstration brushless alternator for the ML-1 mobile nuclear power plant is described. The brushless concept was selected after it became apparent that a conventional power generator could not satisfy the ML-1 weight and size requirements. The demonstration alternator fabricated and tested under this program did not meet all performance specifications; the efficiency was low and the unit could not be operated for significant periods of time without overheating. However, a large body of useful data was accumulated during the extensive development program. Of special interest are data on the rotor and stator design, the cooling requirements and on the distribution of eddy current losses. Analysis of the data indicates that a brushless alternator, only slightly larger and heavier than was specified for the ML-1, could be developed with a modest additional effort.

  17. A dense gas of laser-cooled atoms for hybrid atom-ion trapping

    Science.gov (United States)

    Höltkemeier, Bastian; Glässel, Julian; López-Carrera, Henry; Weidemüller, Matthias

    2017-01-01

    We describe the realization of a dark spontaneous-force trap of rubidium atoms. The atoms are loaded from a beam provided by a two-dimensional magneto-optical trap yielding a capture efficiency of 75%. The dense and cold atomic sample is characterized by saturated absorption imaging. Up to 10^9 atoms are captured with a loading rate of 3× 10^9 atoms/s into a cloud at a temperature of 250 μK with the density exceeding 10^{11} atoms/cm^3. Under steady-state conditions, more than 90% of the atoms can be prepared into the absolute atomic ground state, which provides favorable conditions for the investigation of sympathetic cooling of ions in a hybrid atom-ion trap.

  18. The Cosmic History of Hot Gas Cooling and Radio AGN Activity in Massive Early-Type Galaxies

    Science.gov (United States)

    Danielson, A. L. R.; Lehmer, B. D.; Alexander, D. M.; Brandt, W. M.; Luo, B.; Miller, N.; Xue, Y. Q.; Stott, J. P.

    2012-01-01

    We study the X-ray properties of 393 optically selected early-type galaxies (ETGs) over the redshift range of z approx equals 0.0-1.2 in the Chandra Deep Fields. To measure the average X-ray properties of the ETG population, we use X-ray stacking analyses with a subset of 158 passive ETGs (148 of which were individually undetected in X-ray). This ETG subset was constructed to span the redshift ranges of z = 0.1-1.2 in the approx equals 4 Ms CDF-S and approx equals 2 Ms CDF-N and z = 0.1-0.6 in the approx equals 250 ks E-CDF-S where the contribution from individually undetected AGNs is expected to be negligible in our stacking. We find that 55 of the ETGs are detected individually in the X-rays, and 12 of these galaxies have properties consistent with being passive hot-gas dominated systems (i.e., systems not dominated by an X-ray bright Active Galactic Nucleus; AGN). On the basis of our analyses, we find little evolution in the mean 0.5-2 keY to B-band luminosity ratio (L(sub x) /L(sub Beta) varies as [1 +z]) since z approx equals 1.2, implying that some heating mechanism prevents the gas from cooling in these systems. We consider that feedback from radio-mode AGN activity could be responsible for heating the gas. We select radio AGNs in the ETG population using their far-infrared/radio flux ratio. Our radio observations allow us to constrain the duty cycle history of radio AGN activity in our ETG sample. We estimate that if scaling relations between radio and mechanical power hold out to z approx equals 1.2 for the ETG population being studied here, the average mechanical power from AGN activity is a factor of approx equals1.4 -- 2.6 times larger than the average radiative cooling power from hot gas over the redshift range z approx equals 0-1.2. The excess of inferred AGN mechanical power from these ETGs is consistent with that found in the local Universe for similar types of galaxies.

  19. Cooling and climatisation of buildings and premises with natural gas; Kylning och klimatisering av byggnader och lokaler med hjaelp av naturgas

    Energy Technology Data Exchange (ETDEWEB)

    Lindkvist, A. [Vattenfall Energisystem AB, Stockholm (Sweden)

    1997-04-01

    Today, gas based cooling systems are not profitable in most applications. The economical assessment of natural gas climatisation is dependent of the price difference between gas and electricity. One requirement for good profitability is that the emitted heat, by the refrigeration system, is used. The costs of capital and maintenance are higher for gas based systems compared with those for electrical cooling systems. The profit also depends of the application the system is used in. The natural gas system is favoured by the low difference in temperature between the warm and the cold side of the system. There are three common techniques used for natural gas cooling purposes; the compressor system, the absorption system and the sorption system. Examples on suitable applications for natural gas cooling techniques are computer halls, super-stores, slaughter houses and bath houses. The compressor system is composed of an ordinary compressor refrigeration system powered by a gas engine. The gas engine can be either an Otto engine or a Stirling engine. The Otto engine kind is dominating the market. The absorption system is a refrigeration system using heat as energy source. Only a small amount of electricity is needed. The absorption system is less efficient than the compressor system. The sorption system is commonly used as a dehumidifier. Recently, sorption based refrigeration systems has been introduced to the market. The market volume for district cooling in Sweden 1995 was 30 GWh, which is equivalent to approximately 15 GWh natural gas. At the turn of the century the market for district cooling is estimated to reach 370 GWh/year, which is approximately equivalent to 185 GWh natural gas per year. Research in the refrigeration area is aiming towards higher efficiency with more environmentally acceptable refrigerants.The intention is to find `natural` refrigerants that will enable compressors to reach higher energy factors and that will require less maintenance. The

  20. Stress-optimised, steam-cooled gas turbine blade. Final report; Spannungsoptimierte, dampfgekuehlte Gasturbinenschaufel. Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Kusterer, K.; Kammerer, T.; Kemper, M.; Lang, G.; Roeper, R.

    2002-07-01

    Steam cooling is a technology with a high innovation potential, so it is not surprising that intensive research is done currently especially in the USA and Japan. This project focused on the technological and constructional aspects of the technology, including thermal and thermomechanical design and calculation of a steam-cooled turbine blade as the high temperature gradients and high thermal stresses are a key problem in the implementation of this technology. This is the only EU-wide project with a technological and design-oriented approach. An interdisciplinary was chosen which includes process analysis, numeric simulations and experiments. Results so far are presented. [German] Die Technologie der Dampfkuehlung steht zur Zeit im Mittelpunkt intensiver industrieller Entwicklungsbemuehungen, insbesondere auf amerikanischer und japanischer Seite, weil das hohe Innovationspotenzial dieser Technologie erkannt worden ist. Die Motivation dieses Vorhabens beruht auf der Erkenntnis, dass die Technologie der Dampfkuehlung fuer Gasturbinen in GuD-Kraftwerken eine der Schluesseltechnologien ist, die im Hinblick auf die Wirkungsgradsteigerung der GuD-Anlagen und somit zur CO{sub 2}-Reduzierung eine wesentliche Rolle spielt. Im Vordergrund des Vorhabens stehen technologische und konstruktive Aspekte bei der Umsetzung der Dampfkuehlungstechnologie. Es sollen Erkenntnisse zu technischen Problemen sowie Loesungsansaetze hierzu erbracht werden, die fuer eine erfolgreiche Einfuehrung der innovativen Technologie notwendig sind. Damit verbunden ist die thermische und thermomechanische Auslegung und Berechnung einer dampfgekuehlten Schaufel, da insbesondere die Verbindung von hohen Temperaturgradienten und hohen thermischen Spannungen eine besondere Schwierigkeit bei der Umsetzung dieser Technologie darstellt. Die technisch-konstruktive Zielsetzung zur Umsetzung der Dampfkuehltechnologie fuer Turbinenschaufeln ist dabei im Rahmen europaeischer Forschungsanstrengungen einzigartig. Zur

  1. On Granular Knowledge Structures

    CERN Document Server

    Zeng, Yi

    2008-01-01

    Knowledge plays a central role in human and artificial intelligence. One of the key characteristics of knowledge is its structured organization. Knowledge can be and should be presented in multiple levels and multiple views to meet people's needs in different levels of granularities and from different perspectives. In this paper, we stand on the view point of granular computing and provide our understanding on multi-level and multi-view of knowledge through granular knowledge structures (GKS). Representation of granular knowledge structures, operations for building granular knowledge structures and how to use them are investigated. As an illustration, we provide some examples through results from an analysis of proceeding papers. Results show that granular knowledge structures could help users get better understanding of the knowledge source from set theoretical, logical and visual point of views. One may consider using them to meet specific needs or solve certain kinds of problems.

  2. The injection of liquid cool CO2 in a warm depleted gas reservoir

    NARCIS (Netherlands)

    Hofstee, C.; Maas, J.H.; Loeve, D.

    2013-01-01

    The P18-4 compartment (operated by TAQA Energy B.V.) would be injected by CO2 at a minimum temperature of 12 degrees C. At these temperatures, the CO2 phase will either be a gas or a liquid. As the initial temperature of the reservoir is 120 oC, the CO2 will eventually be the gaseous or (at higher

  3. Implementation of Sub-Cooling of Cryogenic Propellants by Injection of Non-condensing Gas to the Generalized Fluid Systems Simulation Program (GFSSP)

    Science.gov (United States)

    Huggett, Daniel J.; Majumdar, Alok

    2013-01-01

    Cryogenic propellants are readily heated when used. This poses a problem for rocket engine efficiency and effective boot-strapping of the engine, as seen in the "hot" LOX (Liquid Oxygen) problem on the S-1 stage of the Saturn vehicle. In order to remedy this issue, cryogenic fluids were found to be sub-cooled by injection of a warm non-condensing gas. Experimental results show that the mechanism behind the sub-cooling is evaporative cooling. It has been shown that a sub-cooled temperature difference of approximately 13 deg F below saturation temperature [1]. The phenomenon of sub-cooling of cryogenic propellants by a non-condensing gas is not readily available with the General Fluid System Simulation Program (GFSSP) [2]. GFSSP is a thermal-fluid program used to analyze a wide variety of systems that are directly impacted by thermodynamics and fluid mechanics. In order to model this phenomenon, additional capabilities had to be added to GFSSP in the form of a FORTRAN coded sub-routine to calculate the temperature of the sub-cooled fluid. Once this was accomplished, the sub-routine was implemented to a GFSSP model that was created to replicate an experiment that was conducted to validate the GFSSP results.

  4. Cooling of Dense Gas by H2O Line Emission and an Assessment of its Effects in Chondrule-Forming Shocks

    CERN Document Server

    Morris, M A; Ciesla, F J

    2008-01-01

    We consider gas at densities appropriate to protoplanetary disks and calculate its ability to cool due to line radiation emitted by H2O molecules within the gas. Our work follows that of Neufeld & Kaufman (1993; ApJ, 418, 263), expanding on their work in several key aspects, including use of a much expanded line database, an improved escape probability formulism, and the inclusion of dust grains, which can absorb line photons. Although the escape probabilities formally depend on a complicated combination of optical depth in the lines and in the dust grains, we show that the cooling rate including dust is well approximated by the dust-free cooling rate multiplied by a simple function of the dust optical depth. We apply the resultant cooling rate of a dust-gas mixture to the case of a solar nebula shock pertinent to the formation of chondrules, millimeter-sized melt droplets found in meteorites. Our aim is to assess whether line cooling can be neglected in chondrule-forming shocks or if it must be included....

  5. Effect of RANS-Type Turbulence Models on Adiabatic Film Cooling Effectiveness over a Scaled Up Gas Turbine Blade Leading Edge Surface

    Science.gov (United States)

    Yepuri, Giridhara Babu; Talanki Puttarangasetty, Ashok Babu; Kolke, Deepak Kumar; Jesuraj, Felix

    2016-06-01

    Increasing the gas turbine inlet temperature is one of the key technologies in raising gas turbine engine power output. Film cooling is one of the efficient cooling techniques to cool the hot section components of a gas turbine engines in turn the turbine inlet temperature can be increased. This study aims at investigating the effect of RANS-type turbulence models on adiabatic film cooling effectiveness over a scaled up gas turbine blade leading edge surfaces. For the evaluation, five different two equation RANS-type turbulent models have been taken in consideration, which are available in the ANSYS-Fluent. For this analysis, the gas turbine blade leading edge configuration is generated using Solid Works. The meshing is done using ANSYS-Workbench Mesh and ANSYS-Fluent is used as a solver to solve the flow field. The considered gas turbine blade leading edge model is having five rows of film cooling circular holes, one at stagnation line and the two each on either side of stagnation line at 30° and 60° respectively. Each row has the five holes with the hole diameter of 4 mm, pitch of 21 mm arranged in staggered manner and has the hole injection angle of 30° in span wise direction. The experiments are carried in a subsonic cascade tunnel facility at heat transfer lab of CSIR-National Aerospace Laboratory with a Reynolds number of 1,00,000 based on leading edge diameter. From the Computational Fluid Dynamics (CFD) evaluation it is found that K-ɛ Realizable model gives more acceptable results with the experimental values, compared to the other considered turbulence models for this type of geometries. Further the CFD evaluated results, using K-ɛ Realizable model at different blowing ratios are compared with the experimental results.

  6. Discrete particle modeling of granular temperature distribution in a bubbling fluidized bed

    Institute of Scientific and Technical Information of China (English)

    Yurong He; Tianyu Wang; Niels Deen; Martin van Sint Annaland; Hans Kuipers; Dongsheng Wen

    2012-01-01

    The discrete hard sphere particle model (DPM) is applied in this work to study numerically the distributions of particle and bubble granular temperatures in a bubbling fluidized bed.The dimensions of the bed and other parameters are set to correspond to those of Müller et al.(2008).Various drag models and operational parameters are investigated to find their influence on particle and bubble granular temperatures.Various inlet superficial gas velocities are used in this work to obtain their effect on flow characteristics.It is found that the superficial gas velocity has the most important effect on granular temperatures including bubble granular temperature,particle translational granular temperature and particle rotational granular temperature.The drag force model affects more seriously the large scale variables such as the bubble granular temperature.Restitution coefficient influences all granular temperatures to some degree.Simulation results are compared with experimental results by Müller et al.(2008) showing reasonable agreement.

  7. Regional variations in the dense gas heating and cooling in M51 from Herschel far-infrared spectroscopy

    CERN Document Server

    Parkin, T J; Schirm, M R P; Baes, M; Boquien, M; Boselli, A; Cooray, A; Cormier, D; Foyle, K; Karczewski, O L; Lebouteiller, V; de Looze, I; Madden, S C; Roussel, H; Sauvage, M; Spinoglio, L

    2013-01-01

    We present Herschel PACS and SPIRE spectroscopy of the most important far-infrared cooling lines in M51, [CII](158 \\mu m), [NII](122 & 205 \\mu m), [OI](63 and 145 \\mu m) and [OIII](88 \\mu m). We compare the observed flux of these lines with the predicted flux from a photon dominated region model to determine characteristics of the cold gas such as density, temperature and the far-ultraviolet radiation field, G_0, resolving details on physical scales of roughly 600 pc. We find an average [CII]/F_TIR of 4 x 10^{-3}, in agreement with previous studies of other galaxies. A pixel-by-pixel analysis of four distinct regions of M51 shows a radially decreasing trend in both the far-ultraviolet (FUV) radiation field, G_0 and the hydrogen density, n, peaking in the nucleus of the galaxy, then falling off out to the arm and interarm regions. We see for the first time that the FUV flux and gas density are similar in the differing environments of the arm and interarm regions, suggesting that the inherent physical prope...

  8. F-state quenching with CH4 for buffer-gas cooled 171Y b+ frequency standard

    Directory of Open Access Journals (Sweden)

    Y.-Y. Jau

    2015-11-01

    Full Text Available We report that methane, CH4, can be used as an efficient F-state quenching gas for trapped ytterbium ions. The quenching rate coefficient is measured to be (2.8 ± 0.3 × 106 s−1 Torr−1. For applications that use microwave hyperfine transitions of the ground-state 171Y b ions, the CH4 induced frequency shift coefficient and the decoherence rate coefficient are measured as δν/ν = (−3.6 ± 0.1 × 10−6 Torr−1 and 1/T2 = (1.5 ± 0.2 × 105 s−1 Torr−1. In our buffer-gas cooled 171Y b+ microwave clock system, we find that only ≤10−8 Torr of CH4 is required under normal operating conditions to efficiently clear the F-state and maintain ≥85% of trapped ions in the ground state with insignificant pressure shift and collisional decoherence of the clock resonance.

  9. Constitutive modeling and finite element procedure development for stress analysis of prismatic high temperature gas cooled reactor graphite core components

    Energy Technology Data Exchange (ETDEWEB)

    Mohanty, Subhasish, E-mail: smohanty@anl.gov [Argonne National Laboratory, South Cass Avenue, Argonne, IL 60439 (United States); Majumdar, Saurindranath [Argonne National Laboratory, South Cass Avenue, Argonne, IL 60439 (United States); Srinivasan, Makuteswara [U.S. Nuclear Regulatory Commission, Washington, DC 20555 (United States)

    2013-07-15

    Highlights: • Finite element procedure developed for stress analysis of HTGR graphite component. • Realistic fluence profile and reflector brick shape considered for the simulation. • Also realistic H-451 grade material properties considered for simulation. • Typical outer reflector of a GT-MHR type reactor considered for numerical study. • Based on the simulation results replacement of graphite bricks can be scheduled. -- Abstract: High temperature gas cooled reactors, such as prismatic and pebble bed reactors, are increasingly becoming popular because of their inherent safety, high temperature process heat output, and high efficiency in nuclear power generation. In prismatic reactors, hexagonal graphite bricks are used as reflectors and fuel bricks. In the reactor environment, graphite bricks experience high temperature and neutron dose. This leads to dimensional changes (swelling and or shrinkage) of these bricks. Irradiation dimensional changes may affect the structural integrity of the individual bricks as well as of the overall core. The present paper presents a generic procedure for stress analysis of prismatic core graphite components using graphite reflector as an example. The procedure is demonstrated through commercially available ABAQUS finite element software using the option of user material subroutine (UMAT). This paper considers General Atomics Gas Turbine-Modular Helium Reactor (GT-MHR) as a bench mark design to perform the time integrated stress analysis of a typical reflector brick considering realistic geometry, flux distribution and realistic irradiation material properties of transversely isotropic H-451 grade graphite.

  10. Tritium permeation behavior through pyrolytic carbon in tritium production using high-temperature gas-cooled reactor for fusion reactors

    Directory of Open Access Journals (Sweden)

    H. Ushida

    2016-12-01

    Full Text Available Under tritium production method using a high-temperature gas-cooled reactor loaded Li compound, Li compound has to be coated by ceramic materials in order to suppress the spreading of tritium to the whole reactor. Pyrolytic carbon (PyC is a candidate of the coating material because of its high resistance for gas permeation. In this study, hydrogen permeation experiments using a PyC-coated isotropic graphite tube were conducted and hydrogen diffusivity, solubility and permeability were evaluated. Tritium permeation behavior through PyC-coated Li compound particles was simulated by using obtained data. Hydrogen permeation flux through PyC in a steady state is proportional to the hydrogen pressure and is larger than that through Al2O3 which is also candidate coating material. However, total tritium leak within the supposed reactor operation period through the PyC-coated Li compound particles is lower than that through the Al2O3-coated ones because the hydrogen absorption capacity in PyC is considerably larger than that in Al2O3.

  11. CFD-DEM simulation of a conceptual gas-cooled fluidized bed nuclear reactor

    Energy Technology Data Exchange (ETDEWEB)

    Almeida, Lucilla C.; Su, Jian, E-mail: lucillalmeida@gmail.com, E-mail: sujian@nuclear.ufrj.br [Coordenacao dos Programas de Pos-Graduacao (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear; Aguirre, Joao, E-mail: aguirre@rocky-dem.com [Engineering Simulation and Scientific Software (ESSS), Rio de Janeiro, RJ (Brazil)

    2015-07-01

    Several conceptual designs of the fluidized-bed nuclear reactor have been proposed due to its many advantages over conventional nuclear reactors such as PWRs and BWRs. Amongst their characteristics, the enhanced heat transfer and mixing enables a more uniform temperature distribution, reducing the risk of hot-spot and excessive fuel temperature, in addition to resulting in a higher burnup of the fuel. Furthermore, the relationship between the bed height and reactor neutronics turns the coolant flow rate control into a power production mechanism. Moreover, the possibility of removing the fuel by gravity from the movable core in case of a loss-of-cooling accident increases its safety. High-accuracy modeling of particles and coolant flow in fluidized bed reactors is needed to evaluate reliably the thermal-hydraulic efficiency and safety margin. The two-way coupling between solid and fluid can account for high-fidelity solid-solid interaction and reasonable accuracy in fluid calculation and fluid-solid interaction. In the CFD-DEM model, the particles are modeled as a discrete phase, following the DEM approach, whereas the fluid flow is treated as a continuous phase, described by the averaged Navier-Stokes equations on a computational cell scale. In this work, the coupling methodology between Fluent and Rocky is described. The numerical approach was applied to the simulation of a bubbling fluidized bed and the results were compared to experimental data and showed good agreement. (author)

  12. Herschel observations of the Centaurus cluster - the dynamics of cold gas in a cool core

    CERN Document Server

    Mittal, Rupal; Ferland, Gary; Oonk, Raymond; Edge, Alastair C; Canning, Rebecca E A; Russell, Helen; Baum, Stefi A; Böhringer, Hans; Combes, Francoise; Donahue, Megan; Fabian, Andy C; Hatch, Nina A; Hoffer, Aaron; Johnstone, Roderick; McNamara, Brian R; Salomé, Philippe; Tremblay, Grant

    2011-01-01

    Brightest cluster galaxies (BCGs) in the cores of galaxy clusters have distinctly different properties from other low redshift massive ellipticals. The majority of the BCGs in cool-core clusters show signs of active star formation. We present observations of NGC 4696, the BCG of the Centaurus galaxy cluster, at far-infrared (FIR) wavelengths with the Herschel space telescope. Using the PACS spectrometer, we detect the two strongest coolants of the interstellar medium, CII at 157.74 micron and OI at 63.18 micron, and in addition NII at 121.90 micron. The CII emission is extended over a region of 7 kpc with a similar spatial morphology and kinematics to the optical H-alpha emission. This has the profound implication that the optical hydrogen recombination line, H-alpha, the optical forbidden lines, NII 6583 Angstrom, the soft X-ray filaments and the far-infrared CII line all have the same energy source. We also detect dust emission using the PACS and SPIRE photometers at all six wavebands. We perform a detailed...

  13. Gas turbine ceramic-coated-vane concept with convection-cooled porous metal core

    Science.gov (United States)

    Kascak, A. F.; Liebert, C. H.; Handschuh, R. F.; Ludwig, L. P.

    1981-01-01

    Analysis and flow experiments on a ceramic-coated-porous-metal vane concept indicated the feasibility, from a heat transfer standpoint, of operating in a high-temperature (2500 F) gas turbine cascade facility. The heat transfer and pressure drop calculations provided a basis for selecting the ceramic layer thickness (to 0.08 in.), which was found to be the dominant factor in the overall heat transfer coefficient. Also an approximate analysis of the heat transfer in the vane trailing edge revealed that with trailing-edge ejection the ceramic thickness could be reduced to (0.01 in.) in this portion of the vane.

  14. A Design on Filter and Cooling for New Gas Generator%一种新型气体发生器的过滤冷却设计

    Institute of Scientific and Technical Information of China (English)

    陈雨; 杨正才; 仵和平; 杨旗; 蔺美君; 何锋彦

    2013-01-01

      为降低气体发生器燃气温度,提高气体清洁度,设计了一种迷宫式过滤冷却机构,相比传统过滤冷却方式,新设计的气体流通路径增加了280%,气体与吸热片接触面积增加了200%。验证试验结果表明迷宫式过滤冷却机构大大提高了气体的清洁度和降温效果。%  Aimed at low temperature and high purity of gas for gas generator, a kind of labyrinth filter and cooling design of gas generator was proposed. Compared to the traditional way, the gas channel length of new design was increased 280%, and the contact area of gas and heat absorption pieces was increased 200%. The verificated test indicated the labyrinth filter and cooling design improves the purity and cooling effect of gas greatly.

  15. Gas-Microjet Reactive Scattering: Collisions of HCl and DCl with Cool Salty Water.

    Science.gov (United States)

    Faust, Jennifer A; Sobyra, Thomas B; Nathanson, Gilbert M

    2016-02-18

    Liquid microjets provide a powerful means to investigate reactions of gases with salty water in vacuum while minimizing gas-vapor collisions. We use this technique to explore the fate of gaseous HCl and DCl molecules impinging on 8 molal LiCl and LiBr solutions at 238 K. The experiments reveal that HCl or DCl evaporate infrequently if they become thermally accommodated at the surface of either solution. In particular, we observe minimal thermal desorption of HCl following HCl collisions and no distinct evidence for rapid, interfacial DCl→HCl exchange following DCl collisions. These results imply that surface thermal motions are not generally strong enough to propel momentarily trapped HCl or DCl back into the gas phase before they ionize and disappear into solution. Instead, only HCl and DCl molecules that scatter directly from the surface escape entry. These recoiling molecules transfer less energy upon collision to LiBr/H2O than to LiCl/H2O, reflecting the heavier mass of Br(-) than of Cl(-) in the interfacial region.

  16. Strategy and perspective on future energy systems, technological range potentials for gas cooled reactors

    Energy Technology Data Exchange (ETDEWEB)

    Bouchard, J.; Bernard, P.; Pochon, E. [CEA, Grenoble (France)

    2002-04-15

    Over the past century, energy consumption worldwide has increased more than ten-fold and, by the year 2050, is likely to be twice what it is today. This increase of energy demand seems inescapable, in view of the growth of the world population and the right to energy access and development for all countries around the world. The pursuit of energy production in the current conditions, essentially based on fossil fuels, would result in the depletion of all the known oil and gas sources in the world with the risks of scarcity of supply. The economies of many countries, particularly countries who do not have natural fossil resources, could suffer under hardships and uncertainties relating to the oil and gas prices. Another consequence would be a doubling of the annual emissions of greenhouse gases by the year 2050 with its consequences over climate change. Energy savings and renewable energy sources shall contribute to avoid such risks, however it will not be enough, by far, to meet the energy consumption of 9 billion inhabitants across the planet. Nuclear energy has unique advantages as to sustainable development, and could offer a safe and economic solution, with long-term resources and no greenhouse effect.

  17. Gas-cooled reactor commercialization study: introduction scenario and commercialization analyses for process heat applications. Final report, July 8, 1977--November 30, 1977

    Energy Technology Data Exchange (ETDEWEB)

    1977-12-01

    This report identifies and presents an introduction scenario which can lead to the operation of High Temperature Gas Cooled Reactor demonstration plants for combined process heat and electric power generation applications, and presents a commercialization analysis relevant to the organizational and management plans which could implement a development program.

  18. High Pressure Gas Filled RF Cavity Beam Test at the Fermilab MuCool Test Area

    Energy Technology Data Exchange (ETDEWEB)

    Freemire, Ben [Illinois Inst. of Technology, Chicago, IL (United States)

    2013-05-01

    The high energy physics community is continually looking to push the limits with respect to the energy and luminosity of particle accelerators. In the realm of leptons, only electron colliders have been built to date. Compared to hadrons, electrons lose a large amount of energy when accelerated in a ring through synchrotron radiation. A solution to this problem is to build long, straight accelerators for electrons, which has been done with great success. With a new generation of lepton colliders being conceived, building longer, more powerful accelerators is not the most enticing option. Muons have been proposed as an alternative particle to electrons. Muons lose less energy to synchrotron radiation and a Muon Collider can provide luminosity within a much smaller energy range than a comparable electron collider. This allows a circular collider to be built with higher attainable energy than any present electron collider. As part of the accelerator, but separate from the collider, it would also be possible to allow the muons to decay to study neutrinos. The possibility of a high energy, high luminosity muon collider and an abundant, precise source of neutrinos is an attractive one. The technological challenges of building a muon accelerator are many and diverse. Because the muon is an unstable particle, a muon beam must be cooled and accelerated to the desired energy within a short amount of time. This requirement places strict requisites on the type of acceleration and focusing that can be used. Muons are generated as tertiary beams with a huge phase space, so strong magnetic fields are required to capture and focus them. Radio frequency (RF) cavities are needed to capture, bunch and accelerate the muons. Unfortunately, traditional vacuum RF cavities have been shown to break down in the magnetic fields necessary for capture and focusing.

  19. Strandby Harbour on solar cooling. Demonstration of 8.000 m{sup 2} solar collectors combined with flue gas cooling with a absorption cooling system; Combined heat and power plant (CHP); Strandby havn paa solkoeling. Demonstration af 8.000 m{sup 2} solfangere kombineret med roeggaskoeling med absorptionskoeleanlaeg

    Energy Technology Data Exchange (ETDEWEB)

    Soerensen, Flemming (Strandby Varmevaerk, Strandby (Denmark)); Soerensen, Per Alex (PlanEnergi, Skoerping (Denmark)); Ulbjerg, F. (Ramboell, Odense (Denmark)); Sloth, H. (Houe and Olsen, Thisted (Denmark))

    2010-04-15

    The aim of the project was to demonstrate 1) high solar heating ratio (18% annually) at a decentralized natural gas combined heat and power plant; 2) increased efficiency (5% of the heat consumption) in a natural gas CHP by using an extra flue gas cooler and an absorption heat pump; 3) a double tank system where a new tank during winter is used for cooling/ heat storage for the absorption heat pump and during summer for solar heat storage in serial operation with the old tank. The concept of combining solar power, absorption cooling and natural gas-fired small-scale CHP in Strandby met expectations and could be replicated in other CHP plants. However, it is important to note that if major construction modifications in the flue gas condensation system in the boiler or engine are required, the operating hours must not be reduced significantly in the amortisation period for the conversion. (ln)

  20. Peltier cooled PbSe double-heterostructure lasers for IR-gas spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Preier, H.; Bleicher, M.; Riedel, W.; Pfeiffer, H.; Maier, H. (Allgemeine Elektricitaets-Gesellschaft AEG Telefunken, Frankfurt am Main (Germany, F.R.). Forschungsinstitut)

    1977-01-01

    PbS-PbSe-PbS double-heterostructure lasers have been pulse-operated at about 200 K mounted on 4 stage thermoelectric coolers. Emitting at a wavelength of about 5.5 ..mu..m they could be used for NO gas spectroscopy. Operation temperatures of up to 230 K have been achieved with structures consisting of n-type PbS substrates and epitaxial layers of n-type PbSe and Tl doped p-type PbS. The temperature dependence of the threshold current density and the emission wavelength of these DH-lasers was compared with PbSe-homojunction lasers. The use of a germanium etalon for a quick evaluation of the spectral quality of the emitted radiation is described.

  1. Integration of High Temperature Gas-cooled Reactor Technology with Oil Sands Processes

    Energy Technology Data Exchange (ETDEWEB)

    L.E. Demick

    2011-10-01

    This paper summarizes an evaluation of siting an HTGR plant in a remote area supplying steam, electricity and high temperature gas for recovery and upgrading of unconventional crude oil from oil sands. The area selected for this evaluation is the Alberta Canada oil sands. This is a very fertile and active area for bitumen recovery and upgrading with significant quantities piped to refineries in Canada and the U.S Additionally data on the energy consumption and other factors that are required to complete the evaluation of HTGR application is readily available in the public domain. There is also interest by the Alberta oil sands producers (OSP) in identifying alternative energy sources for their operations. It should be noted, however, that the results of this evaluation could be applied to any similar oil sands area.

  2. Cystic Granular Cell Ameloblastoma

    OpenAIRE

    Thillaikarasi, Rathnavel; Balaji, Jayaram; Gupta, Bhawna; Ilayarja, Vadivel; Vani, Nandimandalam Venkata; Vidula, Balachander; Saravanan, Balasubramaniam; Ponniah, Irulandy

    2010-01-01

    Ameloblastoma is a locally aggressive benign epithelial odontogenic tumor, while unicystic ameloblastoma is a relatively less aggressive variant. Although rare in unicystic or cystic ameloblastoma, granular cell change in ameloblastoma is a recognized phenomenon. The purpose of the present article is to report a case of cystic granular cell ameloblastoma in 34-year old female.

  3. Novel concepts and geometries as alternatives to conventional circular pin fins for gas turbine blade cooling applications

    Science.gov (United States)

    Uzol, Oguz

    momentum wake region compared to the wakes of the elliptical fins. Hence, the SEFs and the N fins are found to be excellent alternatives to conventional circular pin fins used in gas turbine blade cooling applications.

  4. Evidence of refilled chamber gas pressure enhancing cooling rate during melt spinning of a Zr50Cu40Al10 alloy

    Institute of Scientific and Technical Information of China (English)

    Hong-wang Yang; Peng Zhang; M J Tan; Yuan Ge; Wan-ping Tian; Rui-chun Wang; Rong-de Li

    2015-01-01

    The inlfuence of the reifl ed gas pressure on the glass forming behaviour of one of the best ternary glass forming al oys Zr50Cu40Al10 was studied for the melt spinning process. The amorphicity of as-quenched ribbons was characterized by X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The reifl ed chamber atmospheric pressure is crucial to the cooling rate of melt spinning. At high vacuum, at pressure less than 0.0001 atm, ful y crystal ine fragments are obtained. Monolithic amorphous ribbons were only obtained at a gas pressure of 0.1 atm or higher. The extended contact length between thecribbons and the copper wheel contributes to the high cooling rate of melt spinning. Higher chamber gas pressure leads to more turbulence of liquid metal beneath the nozzle;therefore, lower pressure is preferable at practical melt spinning processes once glass forming conditions are fulifl ed.

  5. Scaling Studies for High Temperature Test Facility and Modular High Temperature Gas-Cooled Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Richard R. Schult; Paul D. Bayless; Richard W. Johnson; James R. Wolf; Brian Woods

    2012-02-01

    The Oregon State University (OSU) High Temperature Test Facility (HTTF) is an integral experimental facility that will be constructed on the OSU campus in Corvallis, Oregon. The HTTF project was initiated, by the U.S. Nuclear Regulatory Commission (NRC), on September 5, 2008 as Task 4 of the 5-year High Temperature Gas Reactor Cooperative Agreement via NRC Contract 04-08-138. Until August, 2010, when a DOE contract was initiated to fund additional capabilities for the HTTF project, all of the funding support for the HTTF was provided by the NRC via their cooperative agreement. The U.S. Department of Energy (DOE) began their involvement with the HTTF project in late 2009 via the Next Generation Nuclear Plant (NGNP) project. Because the NRC's interests in HTTF experiments were only centered on the depressurized conduction cooldown (DCC) scenario, NGNP involvement focused on expanding the experimental envelope of the HTTF to include steady-state operations and also the pressurized conduction cooldown (PCC).

  6. Structure and cluster formation in granular media

    Indian Academy of Sciences (India)

    S Luding

    2005-06-01

    The two most important phenomena at the basis of granular media are excluded volume and dissipation. The former is captured by the hard sphere model and is responsible for, e.g., crystallization, the latter leads to interesting structures like clusters in non-equilibrium dynamical, freely cooling states. The freely cooling system is examined concerning the energy decay and the cluster evolution in time. Corrections for crystallization and multi-particle contacts are provided, which become more and more important with increasing density.

  7. The Cool ISM in Elliptical Galaxies. II. Gas Content in the Volume - Limited Sample and Results from the Combined Elliptical and Lenticular Surveys

    CERN Document Server

    Welch, Gary A; Young, Lisa M

    2010-01-01

    We report new observations of atomic and molecular gas in a volume limited sample of elliptical galaxies. Combining the elliptical sample with an earlier and similar lenticular one, we show that cool gas detection rates are very similar among low luminosity E and SO galaxies but are much higher among luminous S0s. Using the combined sample we revisit the correlation between cool gas mass and blue luminosity which emerged from our lenticular survey, finding strong support for previous claims that the molecular gas in ellipticals and lenticulars has different origins. Unexpectedly, however, and contrary to earlier claims, the same is not true for atomic gas. We speculate that both the AGN feedback and merger paradigms might offer explanations for differences in detection rates, and might also point towards an understanding of why the two gas phases could follow different evolutionary paths in Es and S0s. Finally we present a new and puzzling discovery concerning the global mix of atomic and molecular gas in ear...

  8. ICP-MS analysis of fission product diffusion in graphite for High-Temperature Gas-Cooled Reactors

    Science.gov (United States)

    Carter, Lukas M.

    Release of radioactive fission products from nuclear fuel during normal reactor operation or in accident scenarios is a fundamental safety concern. Of paramount importance are the understanding and elucidation of mechanisms of chemical interaction, nuclear interaction, and transport phenomena involving fission products. Worldwide efforts to reduce fossil fuel dependence coupled with an increasing overall energy demand have generated renewed enthusiasm toward nuclear power technologies, and as such, these mechanisms continue to be the subjects of vigorous research. High-Temperature Gas-Cooled Reactors (HTGRs or VHTRs) remain one of the most promising candidates for the next generation of nuclear power reactors. An extant knowledge gap specific to HTGR technology derives from an incomplete understanding of fission product transport in major core materials under HTGR operational conditions. Our specific interest in the current work is diffusion in reactor graphite. Development of methods for analysis of diffusion of multiple fission products is key to providing accurate models for fission product release from HTGR core components and the reactor as a whole. In the present work, a specialized diffusion cell has been developed and constructed to facilitate real-time diffusion measurements via ICP-MS. The cell utilizes a helium gas-jet system which transports diffusing fission products to the mass spectrometer using carbon nanoparticles. The setup was designed to replicate conditions present in a functioning HTGR, and can be configured for real-time release or permeation measurements of single or multiple fission products from graphite or other core materials. In the present work, we have analyzed release rates of cesium in graphite grades IG-110, NBG-18, and a commercial grade of graphite, as well as release of iodine in IG-110. Additionally we have investigated infusion of graphite samples with Cs, I, Sr, Ag, and other surrogate fission products for use in release or

  9. On0Line Fuel Failure Monitor for Fuel Testing and Monitoring of Gas Cooled Very High Temperature Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Ayman I. Hawari; Mohamed A. Bourham

    2010-04-22

    IVery High Temperature Reactors (VHTR) utilize the TRISO microsphere as the fundamental fuel unit in the core. The TRISO microsphere (~ 1- mm diameter) is composed of a UO2 kernel surrounded by a porous pyrolytic graphite buffer, an inner pyrolytic graphite layer, a silicon carbide (SiC) coating, and an outer pyrolytic graphite layer. The U-235 enrichment of the fuel is expected to range from 4% – 10% (higher enrichments are also being considered). The layer/coating system that surrounds the UO2 kernel acts as the containment and main barrier against the environmental release of radioactivity. To understand better the behavior of this fuel under in-core conditions (e.g., high temperature, intense fast neutron flux, etc.), the US Department of Energy (DOE) is launching a fuel testing program that will take place at the Advanced Test Reactor (ATR) located at Idaho National Laboratory (INL). During this project North Carolina State University (NCSU) researchers will collaborate with INL staff for establishing an optimized system for fuel monitoring for the ATR tests. In addition, it is expected that the developed system and methods will be of general use for fuel failure monitoring in gas cooled VHTRs.

  10. Evaluation of radiation heat transfer in porous medial: Application for a pebble bed modular reactor cooled by CO2 gas

    Directory of Open Access Journals (Sweden)

    Sidi-Ali Kamel

    2013-01-01

    Full Text Available This work analyses the contribution of radiation heat transfer in the cooling of a pebble bed modular reactor. The mathematical model, developed for a porous medium, is based on a set of equations applied to an annular geometry. Previous major works dealing with the subject have considered the forced convection mode and often did not take into account the radiation heat transfer. In this work, only free convection and radiation heat transfer are considered. This can occur during the removal of residual heat after shutdown or during an emergency situation. In order to derive the governing equations of radiation heat transfer, a steady-state in an isotropic and emissive porous medium (CO2 is considered. The obtained system of equations is written in a dimensionless form and then solved. In order to evaluate the effect of radiation heat transfer on the total heat removed, an analytical method for solving the system of equations is used. The results allow quantifying both radiation and free convection heat transfer. For the studied situation, they show that, in a pebble bed modular reactor, more than 70% of heat is removed by radiation heat transfer when CO2 is used as the coolant gas.

  11. Output Feedback Dissipation Control for the Power-Level of Modular High-Temperature Gas-Cooled Reactors

    Directory of Open Access Journals (Sweden)

    Zhe Dong

    2011-11-01

    Full Text Available Because of its strong inherent safety features and the high outlet temperature, the modular high temperature gas-cooled nuclear reactor (MHTGR is the chosen technology for a new generation of nuclear power plants. Such power plants are being considered for industrial applications with a wide range of power levels, thus power-level regulation is very important for their efficient and stable operation. Exploiting the large scale asymptotic closed-loop stability provided by nonlinear controllers, a nonlinear power-level regulator is presented in this paper that is based upon both the techniques of feedback dissipation and well-established backstepping. The virtue of this control strategy, i.e., the ability of globally asymptotic stabilization, is that it takes advantage of the inherent zero-state detectability property of the MHTGR dynamics. Moreover, this newly built power-level regulator is also robust towards modeling uncertainty in the control rod dynamics. If modeling uncertainty of the control rod dynamics is small enough to be omitted, then this control law can be simplified to a classical proportional feedback controller. The comparison of the control performance between the newly-built power controller and the simplified controller is also given through numerical study and theoretical analysis.

  12. Model based predictive control of a high temperature gas cooled power plant coupled to a hydrogen production facility

    Science.gov (United States)

    Rhoads, Lloyd A.

    This thesis builds upon recent studies focusing on modeling, operation, and control of high temperature gas cooled reactors. A computer model was developed, based on mass, energy, and momentum balances of control volumes throughout the plant. Several simulations of the plant behavior were conducted and their results were compared with those from the literature. Proportional control was combined with optimal control to form a time varying, adjustable gain predictive controller which adjusts the proportional gains during transients. The controller was designed to utilize control rod motions and bypass control valves to maintain desired plant conditions. An optimization scheme was introduced to efficiently solve the optimization problem formulated as part of the predictive controller operation. Several additional transients were run to examine the full plant controller performance. Multiple predictive controllers were designed and their performance was compared with a proportional controller throughout each transient. The predictive controller results confirmed the importance of proper selection of the optimal controller parameters, in particular the controller time step size and the horizon time. The well-designed proportional controllers clearly demonstrated improvements in plant performance during short time scale transients, namely a loss of secondary heat transfer transient and a step change in desired power transient. Results from long time scale transients demonstrated the capabilities of the proposed bypass control system to control electrical power production without the need for storage vessels.

  13. An Artificial Neural Network Compensated Output Feedback Power-Level Control for Modular High Temperature Gas-Cooled Reactors

    Directory of Open Access Journals (Sweden)

    Zhe Dong

    2014-02-01

    Full Text Available Small modular reactors (SMRs could be beneficial in providing electricity power safely and also be viable for applications such as seawater desalination and heat production. Due to its inherent safety features, the modular high temperature gas-cooled reactor (MHTGR has been seen as one of the best candidates for building SMR-based nuclear power plants. Since the MHTGR dynamics display high nonlinearity and parameter uncertainty, it is necessary to develop a nonlinear adaptive power-level control law which is not only beneficial to the safe, stable, efficient and autonomous operation of the MHTGR, but also easy to implement practically. In this paper, based on the concept of shifted-ectropy and the physically-based control design approach, it is proved theoretically that the simple proportional-differential (PD output-feedback power-level control can provide asymptotic closed-loop stability. Then, based on the strong approximation capability of the multi-layer perceptron (MLP artificial neural network (ANN, a compensator is established to suppress the negative influence caused by system parameter uncertainty. It is also proved that the MLP-compensated PD power-level control law constituted by an experientially-tuned PD regulator and this MLP-based compensator can guarantee bounded closed-loop stability. Numerical simulation results not only verify the theoretical results, but also illustrate the high performance of this MLP-compensated PD power-level controller in suppressing the oscillation of process variables caused by system parameter uncertainty.

  14. Gas-cooled reactor programs. Fuel-management positioning and accounting module: FUELMANG Version V1. 11, September 1981

    Energy Technology Data Exchange (ETDEWEB)

    Medlin, T.W.; Hill, K.L.; Johnson, G.L.; Jones, J.E.; Vondy, D.R.

    1982-01-01

    This report documents the code module FUELMANG for fuel management of a reactor. This code may be used to position fuel during the calculation of a reactor history, maintain a mass balance history of the fuel movement, and calculate the unit fuel cycle component of the electrical generation cost. In addition to handling fixed feed fuel without recycle, provision has been made for fuel recycle with various options applied to the recycled fuel. A continuous fueling option is also available with the code. A major edit produced by the code is a detailed summary of the mass balance history of the reactor and a fuel cost analysis of that mass balance history. This code is incorporated in the system containing the VENTURE diffusion theory neutronics code for routine use. Fuel movement according to prescribed instructions is performed without the access of additional user input data during the calculation of a reactor operating history. Local application has been primarily for analysis of the performance of gas-cooled thermal reactor core concepts.

  15. Fuel Summary for Peach Bottom Unit 1 High-Temperature Gas-Cooled Reactor Cores 1 and 2

    Energy Technology Data Exchange (ETDEWEB)

    Karel I. Kingrey

    2003-04-01

    This fuel summary report contains background and summary information for the Peach Bottom Unit 1, High-Temperature, Gas-Cooled Reactor Cores 1 and 2. This report contains detailed information about the fuel in the two cores, the Peach Bottom Unit 1 operating history, nuclear parameters, physical and chemical characteristics, and shipping and storage canister related data. The data in this document have been compiled from a large number of sources and are not qualified beyond the qualification of the source documents. This report is intended to provide an overview of the existing data pertaining to spent fuel management and point to pertinent reference source documents. For design applications, the original source documentation must be used. While all referenced sources are available as records or controlled documents at the Idaho National Engineering and Environmental Laboratory (INEEL), some of the sources were marked as informal or draft reports. This is noted where applicable. In some instances, source documents are not consistent. Where they are known, this document identifies those instances and provides clarification where possible. However, as stated above, this document has not been independently qualified and such clarifications are only included for information purposes. Some of the information in this summary is available in multiple source documents. An effort has been made to clearly identify at least one record document as the source for the information included in this report.

  16. [USA/FRG cooperation in gas-cooled reactor development]. Foreign trip report, June 24--July 2, 1988

    Energy Technology Data Exchange (ETDEWEB)

    Jones, Jr, J E

    1988-07-26

    Reviews were conducted at Kernforschungsanlage (KFA) Juelich of the US and Federal Republic of Germany (FRG) high-temperature gas-cooled reactor (HTGR) programs under the US/FRG Umbrella Agreement, with emphasis on those technology development areas where cooperation is ongoing and planned. Specific subprogram areas are safety; materials; fuels, fission products, and graphite; and Arbeitsgemeinschaft Versuchs-Reaktor (AVR). The purpose was to assess the status of the cooperation, reach agreement on any changes needed, and identify new areas of cooperation. Overall, the agreement has been both effective and beneficial. Ongoing activities complement and support US technology development plans. Discussions were held in the United Kingdom (UK) at the Risley Nuclear Power Development Laboratory regarding a potential graphite technology exchange program between the US Department of Energy and the UK Atomic Energy Authority. A draft agreement was reviewed and appeared to be satisfactory to both parties and ready for signature. A summary of potential areas of activity in the exchange had been prepared by US representatives and was discussed and found to be acceptable to UK representatives.

  17. Reliability Assessment of 2400 MWth Gas-Cooled Fast Reactor Natural Circulation Decay Heat Removal in Pressurized Situations

    Directory of Open Access Journals (Sweden)

    C. Bassi

    2008-01-01

    Full Text Available As the 2400 MWth gas-cooled fast reactor concept makes use of passive safety features in combination with active safety systems, the question of natural circulation decay heat removal (NCDHR reliability and performance assessment into the ongoing probabilistic safety assessment in support to the reactor design, named “probabilistic engineering assessment” (PEA, constitutes a challenge. Within the 5th Framework Program for Research and Development (FPRD of the European Community, a methodology has been developed to evaluate the reliability of passive systems characterized by a moving fluid and whose operation is based on physical principles, such as the natural circulation. This reliability method for passive systems (RMPSs is based on uncertainties propagation into thermal-hydraulic (T-H calculations. The aim of this exercise is finally to determine the performance reliability of the DHR system operating in a “passive” mode, taking into account the uncertainties of parameters retained for thermal-hydraulical calculations performed with the CATHARE 2 code. According to the PEA preliminary results, exhibiting the weight of pressurized scenarios (i.e., with intact primary circuit boundary for the core damage frequency (CDF, the RMPS exercise is first focusing on the NCDHR performance at these T-H conditions.

  18. Efficient transfer of positrons from a buffer-gas-cooled accumulator into an orthogonally oriented superconducting solenoid for antihydrogen studies

    CERN Document Server

    Comeau, D; Fitzakerley, D; George, M C; Hessels, E A; Storry, C H; Weel, M; Grzonka, D; Oelert, W; Gabrielse, G; Kalra, R; Kolthammer, W S; McConnell, R; Richerme, P; Mullers, A; Walz, J

    2012-01-01

    Positrons accumulated in a room-temperature buffer-gas-cooled positron accumulator are efficiently transferred into a superconducting solenoid which houses the ATRAP cryogenic Penning trap used in antihydrogen research. The positrons are guided along a 9 m long magnetic guide that connects the central field lines of the 0.15 T field in the positron accumulator to the central magnetic field lines of the superconducting solenoid. Seventy independently controllable electromagnets are required to overcome the fringing field of the large-bore superconducting solenoid. The guide includes both a 15 degrees upward bend and a 105 degrees downward bend to account for the orthogonal orientation of the positron accumulator with respect to the cryogenic Penning trap. Low-energy positrons ejected from the accumulator follow the magnetic field lines within the guide and are transferred into the superconducting solenoid with nearly 100% efficiency. A 7 m long 5 cm diameter stainless-steel tube and a 20 mm long, 1.5 mm diamet...

  19. Detection of hidden shot balls in a gas-cooled turbine blade with an NRT gadolinium tagging method

    Science.gov (United States)

    Sim, Cheul Muu; Kim, Yi Kyung; Kim, TaeJoo; Lee, Kye Hong; Kim, Jeong Uk

    2009-06-01

    This report provides a preliminary insight into the benefits and effectiveness of neutron radiography in identifying alien materials, namely shot balls hidden in a turbine blade that are otherwise undetected using other methods. The detection of 0.2-mm-diameter shot balls in gas-cooled turbine blades is possible for thermal neutron radiography. A tagging processing is more useful for a distinctive image of newer turbine blades. Areas of concern for the tagging process include the solution concentration and the possibility of a slight washing of the blades. The location of the shot balls within the turbine blades tagged with Gd((2%, 5%)+water) was shown. Shot balls were placed externally on a turbine blade (F100-700, F100-200) surface in order to check for a dead zone from a surface examination. The image is produced from neutron radiography after a 5 min exposure time. When the blade is tagged with 2% and 5% Gd with slight washing, the shot can also be effectively seen on the SR-45 film. Shot balls are more obvious on a neutron image SR-45 film than an image plate or a DR film.

  20. Analysis of Fluid Flow and Heat Transfer Model for the Pebble Bed High Temperature Gas Cooled Reactor

    Directory of Open Access Journals (Sweden)

    S. Yamoah

    2012-06-01

    Full Text Available The pebble bed type high temperature gas cooled nuclear reactor is a promising option for next generation reactor technology and has the potential to provide high efficiency and cost effective electricity generation. The reactor unit heat transfer poses a challenge due to the complexity associated with the thermalflow design. Therefore to reliably simulate the flow and heat transport of the pebble bed modular reactor necessitates a heat transfer model that deals with radiation as well as thermal convection and conduction. In this study, a model with the capability to simulate fluid flow and heat transfer in the pebble bed modular reactor core has been developed. The developed model was implemented on a personal computer using FORTRAN 95 programming language. Several important fluid flow and heat transfer parameters have been examined: including the pressure drop over the reactor core, the heat transfer coefficient, the Nusselt number and the effective thermal conductivity of the fuel pebbles. Results obtained from the simulation experiments show a uniform pressure in the radial direction for a core to fuel element diameter (D/d ratio>20 and the heat transfer coefficient increases with increasing temperature and coolant mass flow rate. The model can adequately account for the flow and heat transfer phenomenon and the loss of pressure through friction in the pebble bed type high temperature nuclear reactor.

  1. Congenital granular cell epulis.

    Science.gov (United States)

    Conrad, Rachel; Perez, Mia C N

    2014-01-01

    Congenital granular cell epulis is a rarely reported lesion of unknown histogenesis with a strong predilection for the maxillary alveolar ridge of newborn girls. Microscopically, it demonstrates nests of polygonal cells with granular cytoplasm, a prominent capillary network, and attenuated overlying squamous epithelium. The lesion lacks immunoreactivity for S-100, laminin, chromogranin, and most other markers except neuron-specific enolase and vimentin. Through careful observation of its unique clinical, histopathologic, and immunohistochemical features, this lesion can be distinguished from the more common adult granular cell tumor as well as other differential diagnoses.

  2. Discrete Element Modeling of Complex Granular Flows

    Science.gov (United States)

    Movshovitz, N.; Asphaug, E. I.

    2010-12-01

    Granular materials occur almost everywhere in nature, and are actively studied in many fields of research, from food industry to planetary science. One approach to the study of granular media, the continuum approach, attempts to find a constitutive law that determines the material's flow, or strain, under applied stress. The main difficulty with this approach is that granular systems exhibit different behavior under different conditions, behaving at times as an elastic solid (e.g. pile of sand), at times as a viscous fluid (e.g. when poured), or even as a gas (e.g. when shaken). Even if all these physics are accounted for, numerical implementation is made difficult by the wide and often discontinuous ranges in continuum density and sound speed. A different approach is Discrete Element Modeling (DEM). Here the goal is to directly model every grain in the system as a rigid body subject to various body and surface forces. The advantage of this method is that it treats all of the above regimes in the same way, and can easily deal with a system moving back and forth between regimes. But as a granular system typically contains a multitude of individual grains, the direct integration of the system can be very computationally expensive. For this reason most DEM codes are limited to spherical grains of uniform size. However, spherical grains often cannot replicate the behavior of real world granular systems. A simple pile of spherical grains, for example, relies on static friction alone to keep its shape, while in reality a pile of irregular grains can maintain a much steeper angle by interlocking force chains. In the present study we employ a commercial DEM, nVidia's PhysX Engine, originally designed for the game and animation industry, to simulate complex granular flows with irregular, non-spherical grains. This engine runs as a multi threaded process and can be GPU accelerated. We demonstrate the code's ability to physically model granular materials in the three regimes

  3. Self-Structuring of Granular material under Capillary Bulldozing

    Science.gov (United States)

    Dumazer, Guillaume; Sandnes, Bjørnar; Ayaz, Monem; Måløy, Knut Jørgen; Flekkøy, Eirik

    2017-06-01

    An experimental observation of the structuring of a granular suspension under the progress of a gas/liquid meniscus in a narrow tube is reported here. The granular material is moved and compactifies as a growing accumulation front. The frictional interaction with the confining walls increases until the pore capillary entry pressure is reached. The gas then penetrates the clogged granular packing and a further accumulation front is formed at the far side of the plug. This cyclic process continues until the gas/liquid interface reaches the tube's outlet, leaving a trail of plugs in the tube. Such 1D pattern formation belongs to a larger family of patterning dynamics observed in 2D Hele-Shaw geometry. The cylindrical geometry considered here provides an ideal case for a theoretical modelling for forced granular matter oscillating between a long frictional phase and a sudden viscous fluidization.

  4. Generation IV nuclear energy system initiative. Large GFR core subassemblydesign for the Gas-Cooled Fast Reactor.

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, E. A.; Kulak, R. F.; Therios, I. U.; Wei, T. Y. C.

    2006-07-31

    Gas-cooled fast reactor (GFR) designs are being developed to meet Gen IV goals of sustainability, economics, safety and reliability, and proliferation resistance and physical protection as part of an International Generation IV Nuclear Energy System Research Initiative effort. Different organizations are involved in the development of a variety of GFR design concepts. The current analysis has focused on the evaluation of low-pressure drop, pin-core designs with favorable passive cooling properties. Initial evaluation of the passive cooling safety case for the GFR during depressurized decay heat removal accidents with concurrent loss of electric power have resulted in requirements for a reduction of core power density to the 100 w/cc level and a low core pressure drop of 0.5 bars. Additional design constraints and the implementation of their constraints are evaluated in this study to enhance and passive cooling properties of the reactor. Passive cooling is made easier by a flat radial distribution of the decay heat. One goal of this study was to evaluate the radial power distribution and determine to what extent it can be flattened, since the decay heat is nearly proportional to the fission power at shutdown. In line with this investigation of the radial power profile, an assessment was also made of the control rod configuration. The layout provided a large number of control rod locations with a fixed area provided for control rods. The number of control rods was consistent with other fast reactor designs. The adequacy of the available control rod locations was evaluated. Future studies will be needed to optimize the control rod designs and evaluate the shutdown system. The case for low pressure drop core can be improved by the minimization of pressure drop sources such as the number of required fuel spacers in the subassembly design and by the details of the fuel pin design. The fuel pin design is determined by a number of neutronic, thermal-hydraulic (gas dynamics

  5. Study of Change of Refrigerant R22 in Units Cooling through simulation in Ecosimpro; Estudio de Cambio de Gas Refrigerante R22 en Unidades enfriadoras mediante simulacion en Ecosimpro

    Energy Technology Data Exchange (ETDEWEB)

    Prieto Urbano, J.; Molina, M. C.; Gavilan, C.; Olmedo, J.

    2013-07-01

    The project is based on the thermodynamic study of the circuit of cooling of cooling units employing the EcosimPro software, with the objective, through analysis of the theoretical performance of cooling units with different gas cooling, find substitute refrigerant gas more suitable for the analyzed units coolers. This study is being conducted due to the regulations of the EC Regulation No. 2037 / 2000, according to the which, starting from the year 2010, it is prohibited to import, produce, sell, and/or use of R-22 Virgin, while the use of recycled R22 allowed until January 1 of the year 2015.

  6. Proposed Advanced Reactor Adaptation of the Standard Review Plan NUREG-0800 Chapter 4 (Reactor) for Sodium-Cooled Fast Reactors and Modular High-Temperature Gas-Cooled Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Belles, Randy [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Poore, III, Willis P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Brown, Nicholas R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Flanagan, George F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Holbrook, Mark [Idaho National Lab. (INL), Idaho Falls, ID (United States); Moe, Wayne [Idaho National Lab. (INL), Idaho Falls, ID (United States); Sofu, Tanju [Argonne National Lab. (ANL), Argonne, IL (United States)

    2017-03-01

    This report proposes adaptation of the previous regulatory gap analysis in Chapter 4 (Reactor) of NUREG 0800, Standard Review Plan (SRP) for the Review of Safety Analysis Reports for Nuclear Power Plants: LWR [Light Water Reactor] Edition. The proposed adaptation would result in a Chapter 4 review plan applicable to certain advanced reactors. This report addresses two technologies: the sodium-cooled fast reactor (SFR) and the modular high temperature gas-cooled reactor (mHTGR). SRP Chapter 4, which addresses reactor components, was selected for adaptation because of the possible significant differences in advanced non-light water reactor (non-LWR) technologies compared with the current LWR-based description in Chapter 4. SFR and mHTGR technologies were chosen for this gap analysis because of their diverse designs and the availability of significant historical design detail.

  7. Finite element based stress analysis of graphite component in high temperature gas cooled reactor core using linear and nonlinear irradiation creep models

    Energy Technology Data Exchange (ETDEWEB)

    Mohanty, Subhasish, E-mail: smohanty@anl.gov; Majumdar, Saurindranath

    2015-10-15

    Highlights: • High temperature gas cooled reactor. • Finite element based stress analysis. • H-451 graphite. • Irradiation creep model. • Graphite reflector stress analysis. - Abstract: Irradiation creep plays a major role in the structural integrity of the graphite components in high temperature gas cooled reactors. Finite element procedures combined with a suitable irradiation creep model can be used to simulate the time-integrated structural integrity of complex shapes, such as the reactor core graphite reflector and fuel bricks. In the present work a comparative study was undertaken to understand the effect of linear and nonlinear irradiation creep on results of finite element based stress analysis. Numerical results were generated through finite element simulations of a typical graphite reflector.

  8. Quantum limit of photothermal cooling

    CERN Document Server

    De Liberato, Simone; Nori, Franco

    2010-01-01

    We study the problem of cooling a mechanical oscillator using the photothermal (bolometric) force. Contrary to previous attempts to model this system, we take into account the noise effects due to the granular nature of photon absorption. This allows us to tackle the cooling problem down to the noise dominated regime and to find reasonable estimates for the lowest achievable phonon occupation in the cantilever.

  9. Theoretical study and design of a low-grade heat-driven pilot ejector refrigeration machine operating with butane and isobutane and intended for cooling of gas transported in a gas-main pipeline

    KAUST Repository

    Petrenko, V.O.

    2011-11-01

    This paper describes the construction and performance of a novel combined system intended for natural gas transportation and power production, and for cooling of gas transported in a gas-main pipeline. The proposed system includes a gas turbine compressor, a combined electrogenerating plant and an ejector refrigeration unit operating with a hydrocarbon refrigerant. The combined electrogenerating plant consists of a high-temperature steam-power cycle and a low-temperature hydrocarbon vapor power cycle, which together comprise a binary vapor system. The combined system is designed for the highest possible effectiveness of power generation and could find wide application in gas-transmission systems of gas-main pipelines. Application of the proposed system would enable year-round power generation and provide cooling of natural gas during periods of high ambient temperature operation. This paper presents the main results of a theoretical study and design performance specifications of a low-grade heat-driven pilot ejector refrigeration machine operating with butane and isobutane. © 2010 Elsevier Ltd and IIR. All rights reserved.

  10. Apparatus and method for maintaining multi-component sample gas constituents in vapor phase during sample extraction and cooling

    Energy Technology Data Exchange (ETDEWEB)

    Felix, Larry Gordon; Farthing, William Earl; Irvin, James Hodges; Snyder, Todd Robert

    2010-05-11

    A dilution apparatus for diluting a gas sample. The apparatus includes a sample gas conduit having a sample gas inlet end and a diluted sample gas outlet end, and a sample gas flow restricting orifice disposed proximate the sample gas inlet end connected with the sample gas conduit and providing fluid communication between the exterior and the interior of the sample gas conduit. A diluted sample gas conduit is provided within the sample gas conduit having a mixing end with a mixing space inlet opening disposed proximate the sample gas inlet end, thereby forming an annular space between the sample gas conduit and the diluted sample gas conduit. The mixing end of the diluted sample gas conduit is disposed at a distance from the sample gas flow restricting orifice. A dilution gas source connected with the sample gas inlet end of the sample gas conduit is provided for introducing a dilution gas into the annular space, and a filter is provided for filtering the sample gas. The apparatus is particularly suited for diluting heated sample gases containing one or more condensable components.

  11. A simplified Probabilistic Safety Assesment of a Steam-Methane Reforming Hydrogen Production Plant coupled to a High-Temperature Gas Cooled Nuclear Reactor

    OpenAIRE

    Nelson Edelstein, Pamela; Flores Flores, Alain; Francois Lacouture, Juan Luis

    2005-01-01

    A Probabilistic Safety Assessment (PSA) is being developed for a steam-methane reforming hydrogen production plant linked to a High-Temperature Gas Cooled Nuclear Reactor (HTGR). This work is based on the Japan Atomic Energy Research Institute’s (JAERI) High Temperature Test Reactor (HTTR) prototype in Japan. This study has two major objectives: calculate the risk to onsite and offsite individuals, and calculate the frequency of different types of damage to the complex. A simplified HAZOP...

  12. Development of Natural Gas Fired Combined Cycle Plant for Tri-Generation of Power, Cooling and Clean Water Using Waste Heat Recovery: Techno-Economic Analysis

    OpenAIRE

    Gowtham Mohan; Sujata Dahal; Uday Kumar; Andrew Martin; Hamid Kayal

    2014-01-01

    Tri-generation is one of the most efficient ways for maximizing the utilization of available energy. Utilization of waste heat (flue gases) liberated by the Al-Hamra gas turbine power plant is analyzed in this research work for simultaneous production of: (a) electricity by combining steam rankine cycle using heat recovery steam generator (HRSG); (b) clean water by air gap membrane distillation (AGMD) plant; and (c) cooling by single stage vapor absorption chiller (VAC). The flue gases liber...

  13. The impact of the weather conditions on the cooling performance of the heat pump driven by an internal natural gas combustion engine

    Directory of Open Access Journals (Sweden)

    Janovcová Martina

    2015-01-01

    Full Text Available Market with sources of heat and cold offers unlimited choice of different power these devices, design technology, efficiency and price categories. New progressive technologies are constantly discovering, about which is still little information, which include heat pumps powered by a combustion engine running on natural gas. A few pieces of these installations are in Slovakia, but no studies about their work and effectiveness under real conditions. This article deals with experimental measurements of gas heat pump efficiency in cooling mode. Since the gas heat pump works only in system air – water, air is the primary low – energy source, it is necessary to monitor the impact of the climate conditions for the gas heat pump performance.

  14. Saturated Adaptive Output-Feedback Power-Level Control for Modular High Temperature Gas-Cooled Reactors

    Directory of Open Access Journals (Sweden)

    Zhe Dong

    2014-11-01

    Full Text Available Small modular reactors (SMRs are those nuclear fission reactors with electrical output powers of less than 300 MWe. Due to its inherent safety features, the modular high temperature gas-cooled reactor (MHTGR has been seen as one of the best candidates for building SMR-based nuclear plants with high safety-level and economical competitive power. Power-level control is crucial in providing grid-appropriation for all types of SMRs. Usually, there exists nonlinearity, parameter uncertainty and control input saturation in the SMR-based plant dynamics. Motivated by this, a novel saturated adaptive output-feedback power-level control of the MHTGR is proposed in this paper. This newly-built control law has the virtues of having relatively neat form, of being strong adaptive to parameter uncertainty and of being able to compensate control input saturation, which are given by constructing Lyapunov functions based upon the shifted-ectropies of neutron kinetics and reactor thermal-hydraulics, giving an online tuning algorithm for the controller parameters and proposing a control input saturation compensator respectively. It is proved theoretically that input-to-state stability (ISS can be guaranteed for the corresponding closed-loop system. In order to verify the theoretical results, this new control strategy is then applied to the large-range power maneuvering control for the MHTGR of the HTR-PM plant. Numerical simulation results show not only the relationship between regulating performance and control input saturation bound but also the feasibility of applying this saturated adaptive control law practically.

  15. Reanalysis of the Gas-cooled fast reactor experiments at the zero power facility Proteus – Spectral indices

    Directory of Open Access Journals (Sweden)

    Girardin G.

    2013-03-01

    Full Text Available PROTEUS is a zero power reactor at the Paul Scherrer Institute which has been employed during the 1970’s to study experimentally the physics of the gas-cooled fast reactor. Reaction rate distributions, flux spectrum and reactivity effects have been measured in several configurations featuring PuO2/UO2 fuel, absorbers, large iron shields, and thorium oxide and thorium metal fuel either distributed quasihomogeneously in the reference PuO2/UO2 lattice or introduced in the form of radial and axial blanket zones. This papers focus on the spectral indices – including fission and capture in 232Th and 237Np - measured in the reference PuO2/UO2 lattices and their predictions with an MCNPX model specially developed for the PROTEUS-GCFR core. Predictions were obtained with JEFF-3.1 and -3.11, ENDF/B-VII.0 and VII.1, and JENDL-3.3 and -4.0. A general good agreement was demonstrated. The ratio of 232Th fission to 239Pu fission, however, was under-predicted by 8.7±2.1% and 6.5±2.1% using ENDF/B-VII.0 and VII.1, respectively. Finally, the capture rates in 237Np tended to be underpredicted by the JEFF and JENDL libraries, although the new cross section in JEFF-3.1.1 slightly improved the 237Np capture to 239Pu fission results (3.4±2.4%.

  16. Reliability study of a special decay heat removal system of a gas-cooled fast reactor demonstrator

    Energy Technology Data Exchange (ETDEWEB)

    Burgazzi, Luciano, E-mail: luciano.burgazzi@enea.it

    2014-12-15

    The European roadmap toward the development of generation IV concepts addresses the safety and reliability assessment of the special system designed for decay heat removal of a gas-cooled fast reactor demonstrator (GFRD). The envisaged system includes the combination of both active and passive means to accomplish the fundamental safety function. Failure probabilities are calculated on various system configurations, according to either pressurized or depressurized accident events under investigation, and integrated with probabilities of occurrence of corresponding hardware components and natural circulation performance assessment. The analysis suggests the improvement of measures against common cause failures (CCF), in terms of an appropriate diversification among the redundant systems, to reduce the system failure risk. Particular emphasis is placed upon passive system reliability assessment, being recognized to be still an open issue, and the approach based on the functional reliability is adopted to address the point. Results highlight natural circulation as a challenging factor for the decay heat removal safety function accomplishment by means of passive devices. With the models presented here, the simplifying assumptions and the limited scenarios considered according to the level of definition of the design, where many systems are not yet established, one can conclude that attention has to be paid to the functional aspects of the passive system, i.e. the ones not pertaining to the “hardware” of the system. In this article the results of the analysis are discussed, where the effects of the analytical assumptions, design options, accident managements on the reliability are examined. The design diversity of the components undergoing CCFs can be effective for the improvement and some accident management measures are also possible by making use of the long grace period in GFRD.

  17. 冰蓄冷技术应用于燃气轮发电机进气冷却%Economic and Technology Analysis of Application of Ice Thermal Storage Technology to Inlet-air of Gas-turbine Cooling

    Institute of Scientific and Technical Information of China (English)

    曾淼; 叶水泉; 董兴杰; 陈永林

    2002-01-01

    Gas-turbine is constant flow engine, its power is direct proportion of air mass flow. Reducing the inlet-airtemperature will increase the output of gas-turbine. This paper analyzed the feasibility of the application of ice-thernal storagetechnology to inlet-air of gas-turbine cooling. It concludes that this application is feasible on both technology and economicsides.

  18. Gas turbine

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Ok Ryong

    2004-01-15

    This book introduces gas turbine cycle explaining general thing of gas turbine, full gas turbine cycle, Ericson cycle and Brayton cycle, practical gas turbine cycle without pressure loss, multiaxial type gas turbine cycle and special gas turbine cycle, application of basic theory on a study on suction-cooling gas turbine cycle with turbo-refrigerating machine using the bleed air, and general performance characteristics of the suction-cooling gas turbine cycle combined with absorption-type refrigerating machine.

  19. Granular computing: perspectives and challenges.

    Science.gov (United States)

    Yao, JingTao; Vasilakos, Athanasios V; Pedrycz, Witold

    2013-12-01

    Granular computing, as a new and rapidly growing paradigm of information processing, has attracted many researchers and practitioners. Granular computing is an umbrella term to cover any theories, methodologies, techniques, and tools that make use of information granules in complex problem solving. The aim of this paper is to review foundations and schools of research and to elaborate on current developments in granular computing research. We first review some basic notions of granular computing. Classification and descriptions of various schools of research in granular computing are given. We also present and identify some research directions in granular computing.

  20. Using Cool Roofs to Reduce Energy Use, Greenhouse Gas Emissions, and Urban Heat-island Effects: Findings from an India Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Akbari, Hashem; Xu, Tengfang; Taha, Haider; Wray, Craig; Sathaye, Jayant; Garg, Vishal; Tetali, Surekha; Babu, M. Hari; Reddy, K. Niranjan

    2011-05-25

    Cool roofs, cool pavements, and urban vegetation reduce energy use in buildings, lower local air pollutant concentrations, and decrease greenhouse gas emissions from urban areas. This report summarizes the results of a detailed monitoring project in India and related simulations of meteorology and air quality in three developing countries. The field results quantified direct energy savings from installation of cool roofs on individual commercial buildings. The measured annual energy savings potential from roof-whitening of previously black roofs ranged from 20-22 kWh/m2 of roof area, corresponding to an air-conditioning energy use reduction of 14-26% in commercial buildings. The study estimated that typical annual savings of 13-14 kWh/m2 of roof area could be achieved by applying white coating to uncoated concrete roofs on commercial buildings in the Metropolitan Hyderabad region, corresponding to cooling energy savings of 10-19%. With the assumption of an annual increase of 100,000 square meters of new roof construction for the next 10 years in the Metropolitan Hyderabad region, the annual cooling energy savings due to whitening concrete roof would be 13-14 GWh of electricity in year ten alone, with cumulative 10-year cooling energy savings of 73-79 GWh for the region. The estimated savings for the entire country would be at least 10 times the savings in Hyderabad, i.e., more than 730-790 GWh. We estimated that annual direct CO2 reduction associated with reduced energy use would be 11-12 kg CO2/m2 of flat concrete roof area whitened, and the cumulative 10-year CO2 reduction would be approximately 0.60-0.65 million tons in India. With the price of electricity estimated at seven Rupees per kWh, the annual electricity savings on air-conditioning would be approximately 93-101 Rupees per m2 of roof. This would translate into annual national savings of approximately one billion Rupees in year ten, and cumulative 10-year savings of over five billion Rupees for cooling

  1. Dopant-assisted negative photoionization Ion mobility spectrometry coupled with on-line cooling inlet for real-time monitoring H2S concentration in sewer gas.

    Science.gov (United States)

    Peng, Liying; Jiang, Dandan; Wang, Zhenxin; Hua, Lei; Li, Haiyang

    2016-06-01

    Malodorous hydrogen sulfide (H2S) gas often exists in the sewer system and associates with the problems of releasing the dangerous odor to the atmosphere and causing sewer pipe to be corroded. A simple method is in demand for real-time measuring H2S level in the sewer gas. In this paper, an innovated method based on dopant-assisted negative photoionization ion mobility spectrometry (DANP-IMS) with on-line semiconductor cooling inlet was put forward and successfully applied for the real-time measurement of H2S in sewer gas. The influence of moisture was effectively reduced via an on-line cooling method and a non-equilibrium dilution with drift gas. The limits of quantitation for the H2S in ≥60% relative humidity air could be obtained at ≤79.0ng L(-1) with linear ranges of 129-2064ng L(-1). The H2S concentration in a sewer manhole was successfully determined while its product ions were identified by an ion-mobility time-of-fight mass spectrometry. Finally, the correlation between sewer H2S concentration and the daily routines and habits of residents was investigated through hourly or real-time monitoring the variation of sewer H2S in manholes, indicating the power of this DANP-IMS method in assessing the H2S concentration in sewer system. Copyright © 2016 Elsevier B.V. All rights reserved.

  2. Shaken Granular Lasers

    CERN Document Server

    Folli, Viola; Leuzzi, Luca; Conti, Claudio

    2012-01-01

    Granular materials have been studied for decades, also driven by industrial and technological applications. These very simple systems, composed by agglomerations of mesoscopic particles, are characterized, in specific regimes, by a large number of metastable states and an extreme sensitivity (e.g., in sound transmission) on the arrangement of grains; they are not substantially affected by thermal phenomena, but can be controlled by mechanical solicitations. Laser emission from shaken granular matter is so far unexplored; here we provide experimental evidence that it can be affected and controlled by the status of motion of the granular, we also find that competitive random lasers can be observed. We hence demonstrate the potentialities of gravity affected moving disordered materials for optical applications, and open the road to a variety of novel interdisciplinary investigations, involving modern statistical mechanics and disordered photonics.

  3. Shaken granular lasers.

    Science.gov (United States)

    Folli, Viola; Puglisi, Andrea; Leuzzi, Luca; Conti, Claudio

    2012-06-15

    Granular materials have been studied for decades, driven by industrial and technological applications. These very simple systems, composed of agglomerations of mesoscopic particles, are characterized, in specific regimes, by a large number of metastable states and an extreme sensitivity (e.g., in sound transmission) to the arrangement of grains; they are not substantially affected by thermal phenomena, but can be controlled by mechanical solicitations. Laser emission from shaken granular matter is so far unexplored. Here we provide experimental evidence that laser emission can be affected and controlled by the status of the motion of the granular material; we also find that competitive random lasers can be observed. We hence demonstrate the potentialities of gravity-affected moving disordered materials for optical applications, and open the road to a variety of novel interdisciplinary investigations, involving modern statistical mechanics and disordered photonics.

  4. Numerical Simulation of Plasma-Dynamical Processes in the Technological Inductively Coupled RF Plasmatron with Gas Cooling

    Directory of Open Access Journals (Sweden)

    Yu. M. Grishin

    2016-01-01

    Full Text Available The electrodeless inductively coupled RF plasmatron (ICP torches became widely used in various fields of engineering, science and technology. Presently, owing to development of new technologies to produce very pure substances, nanopowders, etc., there is a steadily increasing interest in the induction plasma. This generates a need for a broad range of theoretical and experimental studies to optimize the design and technological parameters of different ICP equipment.The paper presents a numerical model to calculate parameters of inductively coupled RF plasmatron with gas-cooling flow. A finite volume method is used for a numerical solution of a system of Maxwell's and heat transfer equations in the application package ANSYS CFX (14.5. The pseudo-steady approach to solving problems is used.A numerical simulation has been computed in the application package ANSYS CFX (14.5 for a specific design option of the technological ICP, which has a three-coils inductor and current amplitude in the range J к = 50-170 A (3 MHz. The pure argon flows in the ICP. The paper discusses how the value of discharge current impacts on the thermodynamic parameters (pressure, temperature and the power energy in discharge zone. It shows that the ICP can generate a plasma stream with a maximum temperature of about 10 kK and an output speed of 10-15 m/s. The work determines a length of the plasma stream with a weight average temperature of more than 4 kK. It has been found that in order to keep the quartz walls in normal thermal state, the discharge current amplitude should not exceed 150 A. The paper shows the features of the velocity field distribution in the channel of the plasma torch, namely, the formation of vortex in the position of the first coil. The results obtained are important for calculating the dynamics of heating and evaporation of quartz particles in the manufacturing processes for plasma processing of quartz concentrate into high-purity quartz and

  5. Metal-poor, Cool Gas in the Circumgalactic Medium of a z = 2.4 Star-forming Galaxy: Direct Evidence for Cold Accretion?

    Science.gov (United States)

    Crighton, Neil H. M.; Hennawi, Joseph F.; Prochaska, J. Xavier

    2013-10-01

    In our current galaxy formation paradigm, high-redshift galaxies are predominantly fueled by accretion of cool, metal-poor gas from the intergalactic medium. Hydrodynamical simulations predict that this material should be observable in absorption against background sightlines within a galaxy's virial radius, as optically thick Lyman limit systems (LLSs) with low metallicities. Here we report the discovery of exactly such a strong metal-poor absorber at an impact parameter R = 58 kpc from a star-forming galaxy at z = 2.44. Besides strong neutral hydrogen (N_{{H}^0}=10^{19.50+/- 0.16}\\, cm^{-2}) we detect neutral deuterium and oxygen, allowing a precise measurement of the metallicity: log10(Z/Z ⊙) = -2.0 ± 0.17, or (7-15) × 10-3 solar. Furthermore, the narrow deuterium linewidth requires a cool temperature 0.1 solar, 10 times larger than the metal-poor component. We conclude that the photoionized circumgalactic medium (CGM) of this galaxy is highly inhomogeneous: the majority of the gas is in a cool, metal-poor and predominantly neutral phase, but the majority of the metals are in a highly ionized phase exhibiting weak neutral hydrogen absorption but strong metal absorption. If such inhomogeneity is common, then high-resolution spectra and detailed ionization modeling are critical to accurately appraise the distribution of metals in the high-redshift CGM. .

  6. Metal-Poor, Cool Gas in the Circumgalactic Medium of a z = 2.4 Star-Forming Galaxy: Direct Evidence for Cold Accretion?

    CERN Document Server

    Crighton, Neil H M; Prochaska, J Xavier

    2013-01-01

    In our current galaxy formation paradigm, high-redshift galaxies are predominantly fuelled by accretion of cool, metal-poor gas from the intergalactic medium. Hydrodynamical simulations predict that this material should be observable in absorption against background sightlines within a galaxy's virial radius, as optically thick Lyman-limit systems (LLSs) with low metallicities. Here we report the discovery of exactly such a strong metal-poor absorber at an impact parameter R_perp = 58 kpc from a star-forming galaxy at z = 2.44. Besides strong neutral hydrogen [N(HI) = 10^(19.50 +/- 0.16) cm^-2] we detect neutral deuterium and oxygen, allowing a precise measurement of the metallicity: log10(Z / Zsolar) = -2.0 +/- 0.17, or (7-15) x 10^-3 solar. Furthermore, the narrow deuterium linewidth requires a cool temperature 0.1 solar, ten times larger than the metal-poor component. We conclude that the photoionized circumgalactic medium (CGM) of this galaxy is highly inhomogeneous: the majority of the gas is in a cool,...

  7. Development of Natural Gas Fired Combined Cycle Plant for Tri-Generation of Power, Cooling and Clean Water Using Waste Heat Recovery: Techno-Economic Analysis

    Directory of Open Access Journals (Sweden)

    Gowtham Mohan

    2014-10-01

    Full Text Available Tri-generation is one of the most efficient ways for maximizing the utilization of available energy. Utilization of waste heat (flue gases liberated by the Al-Hamra gas turbine power plant is analyzed in this research work for simultaneous production of: (a electricity by combining steam rankine cycle using heat recovery steam generator (HRSG; (b clean water by air gap membrane distillation (AGMD plant; and (c cooling by single stage vapor absorption chiller (VAC. The flue gases liberated from the gas turbine power cycle is the prime source of energy for the tri-generation system. The heat recovered from condenser of steam cycle and excess heat available at the flue gases are utilized to drive cooling and desalination cycles which are optimized based on the cooling energy demands of the villas. Economic and environmental benefits of the tri-generation system in terms of cost savings and reduction in carbon emissions were analyzed. Energy efficiency of about 82%–85% is achieved by the tri-generation system compared to 50%–52% for combined cycles. Normalized carbon dioxide emission per MW·h is reduced by 51.5% by implementation of waste heat recovery tri-generation system. The tri-generation system has a payback period of 1.38 years with cumulative net present value of $66 million over the project life time.

  8. Effect of Turbulence Intensity on Cross-Injection Film Cooling at a Stepped or Smooth Endwall of a Gas Turbine Vane Passage

    Directory of Open Access Journals (Sweden)

    Pey-Shey Wu

    2014-01-01

    Full Text Available This study is concerned with a film cooling technique applicable to the protection of the endwalls of a gas turbine vane. In the experiments, cross-injection coolant flow from two-row, paired, inclined holes with nonintersecting centerlines was utilized. The test model is a scaled two-half vane. The levels of turbulence intensity used in the experiments are T.I.=1.8%, 7%, and 12%. Other parameters considered in the film cooling experiments include three inlet Reynolds numbers (9.20×104 , 1.24×105, and  1.50×105, three blowing ratios (0.5, 1.0, and 2.0, and three endwall conditions (smooth endwall and stepped endwall with forward-facing or backward-facing step. Thermochromic liquid crystal (TLC technique with steady-state heat transfer experiments was used to obtain the whole-field film cooling effectiveness. Results show that, at low turbulence intensity, increasing Reynolds number decreases the effectiveness in most of the vane passage. There is no monotonic trend of influence by Reynolds number at high turbulence intensity. The effect of blowing ratio on the effectiveness has opposite trends at low and high turbulence levels. Increasing turbulent intensity decreases the effectiveness, especially near the inlet of the vane passage. With a stepped endwall, turbulence intensity has only mild effect on the film cooling effectiveness.

  9. Effect of thermal barrier coatings on the performance of steam and water-cooled gas turbine/steam turbine combined cycle system

    Science.gov (United States)

    Nainiger, J. J.

    1978-01-01

    An analytical study was made of the performance of air, steam, and water-cooled gas-turbine/steam turbine combined-cycle systems with and without thermal-barrier coatings. For steam cooling, thermal barrier coatings permit an increase in the turbine inlet temperature from 1205 C (2200 F), resulting in an efficiency improvement of 1.9 percentage points. The maximum specific power improvement with thermal barriers is 32.4 percent, when the turbine inlet temperature is increased from 1425 C (2600 F) to 1675 C (3050 F) and the airfoil temperature is kept the same. For water cooling, the maximum efficiency improvement is 2.2 percentage points at a turbine inlet temperature of 1683 C (3062 F) and the maximum specific power improvement is 36.6 percent by increasing the turbine inlet temperature from 1425 C (2600 F) to 1730 C (3150 F) and keeping the airfoil temperatures the same. These improvements are greater than that obtained with combined cycles using air cooling at a turbine inlet temperature of 1205 C (2200 F). The large temperature differences across the thermal barriers at these high temperatures, however, indicate that thermal stresses may present obstacles to the use of coatings at high turbine inlet temperatures.

  10. Effect of turbulence intensity on cross-injection film cooling at a stepped or smooth endwall of a gas turbine vane passage.

    Science.gov (United States)

    Wu, Pey-Shey; Tsai, Shen-Ta; Jhuo, Yue-Hua

    2014-01-01

    This study is concerned with a film cooling technique applicable to the protection of the endwalls of a gas turbine vane. In the experiments, cross-injection coolant flow from two-row, paired, inclined holes with nonintersecting centerlines was utilized. The test model is a scaled two-half vane. The levels of turbulence intensity used in the experiments are T.I. = 1.8%, 7%, and 12%. Other parameters considered in the film cooling experiments include three inlet Reynolds numbers (9.20 × 10(4), 1.24 × 10(5), and 1.50 × 10(5)), three blowing ratios (0.5, 1.0, and 2.0), and three endwall conditions (smooth endwall and stepped endwall with forward-facing or backward-facing step). Thermochromic liquid crystal (TLC) technique with steady-state heat transfer experiments was used to obtain the whole-field film cooling effectiveness. Results show that, at low turbulence intensity, increasing Reynolds number decreases the effectiveness in most of the vane passage. There is no monotonic trend of influence by Reynolds number at high turbulence intensity. The effect of blowing ratio on the effectiveness has opposite trends at low and high turbulence levels. Increasing turbulent intensity decreases the effectiveness, especially near the inlet of the vane passage. With a stepped endwall, turbulence intensity has only mild effect on the film cooling effectiveness.

  11. Laser cooling of solids

    OpenAIRE

    Nemova, Galina

    2009-01-01

    Parallel to advances in laser cooling of atoms and ions in dilute gas phase, which has progressed immensely, resulting in physics Nobel prizes in 1997 and 2001, major progress has recently been made in laser cooling of solids. I compare the physical nature of the laser cooling of atoms and ions with that of the laser cooling of solids. I point out all advantages of this new and very promising area of laser physics. Laser cooling of solids (optical refrigeration) at the present time can be lar...

  12. Failure of granular assemblies

    OpenAIRE

    Welker, Philipp

    2011-01-01

    This work investigates granular assemblies subjected to increasing external forces in the quasi-static limit. In this limit, the system’s evolution depends on static properties of the system, but is independent of the particles’ inertia. At the failure, which occurs at a certain value of the external forces, the particles’ motions increase quickly. In this thesis, the properties of granular systems during the weakening process and at the failure are investigated with the Discrete Element Meth...

  13. Rough-Granular Computing

    Institute of Scientific and Technical Information of China (English)

    Andrzej Skowron

    2006-01-01

    Solving complex problems by multi-agent systems in distributed environments requires new approximate reasoning methods based on new computing paradigms. One such recently emerging computing paradigm is Granular Computing(GC). We discuss the Rough-Granular Computing(RGC) approach to modeling of computations in complex adaptive systems and multiagent systems as well as for approximate reasoning about the behavior of such systems. The RGC methods have been successfully applied for solving complex problems in areas such as identification of objects or behavioral patterns by autonomous systems, web mining, and sensor fusion.

  14. Impact of granular drops

    KAUST Repository

    Marston, J. O.

    2013-07-15

    We investigate the spreading and splashing of granular drops during impact with a solid target. The granular drops are formed from roughly spherical balls of sand mixed with water, which is used as a binder to hold the ball together during free-fall. We measure the instantaneous spread diameter for different impact speeds and find that the normalized spread diameter d/D grows as (tV/D)1/2. The speeds of the grains ejected during the “splash” are measured and they rarely exceed twice that of the impact speed.

  15. Velocity Fluctuations in Electrostatically Driven Granular Media

    OpenAIRE

    Aranson, I. S.; Olafsen, J. S.

    2001-01-01

    We study experimentally the particle velocity fluctuations in an electrostatically driven dilute granular gas. The experimentally obtained velocity distribution functions have strong deviations from Maxwellian form in a wide range of parameters. We have found that the tails of the distribution functions are consistent with a stretched exponential law with typical exponents of the order 3/2. Molecular dynamic simulations shows qualitative agreement with experimental data. Our results suggest t...

  16. Modelling of heat and mass transfer in a granular medium during high-temperature air drying. Effect of the internal gas pressure

    Science.gov (United States)

    Othmani, Hammouda; Hassini, Lamine; Lamloumi, Raja; El Cafsi, Mohamed Afif

    2016-02-01

    A comprehensive internal heat and water transfer model including the gas pressure effect has been proposed in order to improve the industrial high-temperature air drying of inserts made of agglomerated sand. In this model, the internal gas phase pressure effect was made perfectly explicit, by considering the liquid and vapour transfer by filtration and the liquid expulsion at the surface. Wet sand enclosed in a tight cylindrical glass bottle dried convectively at a high temperature was chosen as an application case. The model was validated on the basis of the experimental average water content and core temperature curves for drying trials at different operating conditions. The simulations of the spatio-temporal distribution of internal gas pressure were performed and interpreted in terms of product potential damage. Based on a compromise between the drying time and the pressure increase, a simple drying cycle was implemented in order to optimize the drying process.

  17. Plutonium and Minor Actinide Management in Thermal High-Temperature Gas-Cooled Reactors. Publishable Final Activity Report

    Energy Technology Data Exchange (ETDEWEB)

    Kuijper, J.C., E-mail: kuijper@nrg.eu [Nuclear Research and Consultancy Group (NRG), Petten (Netherlands); Somers, J.; Van Den Durpel, L.; Chauvet, V.; Cerullo, N.; Cetnar, J.; Abram, T.; Bakker, K.; Bomboni, E.; Bernnat, W.; Domanska, J.G.; Girardi, E.; De Haas, J.B.M.; Hesketh, K.; Hiernaut, J.P.; Hossain, K.; Jonnet, J.; Kim, Y.; Kloosterman, J.L.; Kopec, M.; Murgatroyd, J.; Millington, D.; Lecarpentier, D.; Lomonaco, G.; McEachern, D.; Meier, A.; Mignanelli, M.; Nabielek, H.; Oppe, J.; Petrov, B.Y.; Pohl, C.; Ruetten, H.J.; Schihab, S.; Toury, G.; Trakas, C.; Venneri, F.; Verfondern, K.; Werner, H.; Wiss, T.; Zakova, J.

    2010-11-15

    The PUMA project -the acronym stands for 'Plutonium and Minor Actinide Management in Thermal High-Temperature Gas-Cooled Reactors'- was a Specific Targeted Research Project (STREP) within the EURATOM 6th Framework Program (EU FP6). The PUMA project ran from September 1, 2006, until August 31, 2009, and was executed by a consortium of 14 European partner organisations and one from the USA. This report serves 2 purposes. It is both the 'Publishable Final Activity Report' and the 'Final (Summary) Report', describing, per Work Package, the specific objectives, research activities, main conclusions, recommendations and supporting documents. PUMA's main objective was to investigate the possibilities for the utilisation and transmutation of plutonium and especially minor actinides in contemporary and future (high temperature) gas-cooled reactor designs, which are promising tools for improving the sustainability of the nuclear fuel cycle. This contributes to the reduction of Pu and MA stockpiles, and also to the development of safe and sustainable reactors for CO{sub 2}-free energy generation. The PUMA project has assessed the impact of the introduction of Pu/MA-burning HTRs at three levels: fuel and fuel performance (modelling), reactor (transmutation performance and safety) and reactor/fuel cycle facility park. Earlier projects already indicated favourable characteristics of HTRs with respect to Pu burning. So, core physics of Pu/MA fuel cycles for HTRs has been investigated to study the CP fuel and reactor characteristics and to assure nuclear stability of a Pu/MA HTR core, under both normal and abnormal operating conditions. The starting point of this investigation comprised the two main contemporary HTR designs, viz. the pebble-bed type HTR, represented by the South-African PBMR, and hexagonal block type HTR, represented by the GT-MHR. The results (once again) demonstrate the flexibility of the contemporary (and near future) HTR

  18. Plutonium and Minor Actinide Management in Thermal High-Temperature Gas-Cooled Reactors. Publishable Final Activity Report

    Energy Technology Data Exchange (ETDEWEB)

    Kuijper, J.C., E-mail: kuijper@nrg.eu [Nuclear Research and Consultancy Group (NRG), Petten (Netherlands); Somers, J.; Van Den Durpel, L.; Chauvet, V.; Cerullo, N.; Cetnar, J.; Abram, T.; Bakker, K.; Bomboni, E.; Bernnat, W.; Domanska, J.G.; Girardi, E.; De Haas, J.B.M.; Hesketh, K.; Hiernaut, J.P.; Hossain, K.; Jonnet, J.; Kim, Y.; Kloosterman, J.L.; Kopec, M.; Murgatroyd, J.; Millington, D.; Lecarpentier, D.; Lomonaco, G.; McEachern, D.; Meier, A.; Mignanelli, M.; Nabielek, H.; Oppe, J.; Petrov, B.Y.; Pohl, C.; Ruetten, H.J.; Schihab, S.; Toury, G.; Trakas, C.; Venneri, F.; Verfondern, K.; Werner, H.; Wiss, T.; Zakova, J.

    2010-11-15

    The PUMA project -the acronym stands for 'Plutonium and Minor Actinide Management in Thermal High-Temperature Gas-Cooled Reactors'- was a Specific Targeted Research Project (STREP) within the EURATOM 6th Framework Program (EU FP6). The PUMA project ran from September 1, 2006, until August 31, 2009, and was executed by a consortium of 14 European partner organisations and one from the USA. This report serves 2 purposes. It is both the 'Publishable Final Activity Report' and the 'Final (Summary) Report', describing, per Work Package, the specific objectives, research activities, main conclusions, recommendations and supporting documents. PUMA's main objective was to investigate the possibilities for the utilisation and transmutation of plutonium and especially minor actinides in contemporary and future (high temperature) gas-cooled reactor designs, which are promising tools for improving the sustainability of the nuclear fuel cycle. This contributes to the reduction of Pu and MA stockpiles, and also to the development of safe and sustainable reactors for CO{sub 2}-free energy generation. The PUMA project has assessed the impact of the introduction of Pu/MA-burning HTRs at three levels: fuel and fuel performance (modelling), reactor (transmutation performance and safety) and reactor/fuel cycle facility park. Earlier projects already indicated favourable characteristics of HTRs with respect to Pu burning. So, core physics of Pu/MA fuel cycles for HTRs has been investigated to study the CP fuel and reactor characteristics and to assure nuclear stability of a Pu/MA HTR core, under both normal and abnormal operating conditions. The starting point of this investigation comprised the two main contemporary HTR designs, viz. the pebble-bed type HTR, represented by the South-African PBMR, and hexagonal block type HTR, represented by the GT-MHR. The results (once again) demonstrate the flexibility of the contemporary (and near future) HTR

  19. BOOK REVIEW: Kinetic Theory of Granular Gases

    Science.gov (United States)

    Trizac, Emmanuel

    2005-11-01

    Granular gases are composed of macroscopic bodies kept in motion by an external energy source such as a violent shaking. The behaviour of such systems is quantitatively different from that of ordinary molecular gases: due to the size of the constituents, external fields have a stronger effect on the dynamics and, more importantly, the kinetic energy of the gas is no longer a conserved quantity. The key role of the inelasticity of collisions has been correctly appreciated for about fifteen years, and the ensuing consequences in terms of phase behaviour or transport properties studied in an increasing and now vast body of literature. The purpose of this book is to help the newcomer to the field in acquiring the essential theoretical tools together with some numerical techniques. As emphasized by the authors—who were among the pioneers in the domain— the content could be covered in a one semester course for advanced undergraduates, or it could be incorporated in a more general course dealing with the statistical mechanics of dissipative systems. The book is self-contained, clear, and avoids mathematical complications. In order to elucidate the main physical ideas, heuristic points of views are sometimes preferred to a more rigorous route that would lead to a longer discussion. The 28 chapters are short; they offer exercises and worked examples, solved at the end of the book. Each part is supplemented with a relevant foreword and a useful summary including take-home messages. The editorial work is of good quality, with very few typographical errors. In spite of the title, kinetic theory stricto sensu is not the crux of the matter covered. The authors discuss the consequences of the molecular chaos assumption both at the individual particle level and in terms of collective behaviour. The first part of the book addresses the mechanics of grain collisions. It is emphasized that considering the coefficient of restitution ɛ —a central quantity governing the

  20. Scales and kinetics of granular flows.

    Science.gov (United States)

    Goldhirsch, I.

    1999-09-01

    When a granular material experiences strong forcing, as may be the case, e.g., for coal or gravel flowing down a chute or snow (or rocks) avalanching down a mountain slope, the individual grains interact by nearly instantaneous collisions, much like in the classical model of a gas. The dissipative nature of the particle collisions renders this analogy incomplete and is the source of a number of phenomena which are peculiar to "granular gases," such as clustering and collapse. In addition, the inelasticity of the collisions is the reason that granular gases, unlike atomic ones, lack temporal and spatial scale separation, a fact manifested by macroscopic mean free paths, scale dependent stresses, "macroscopic measurability" of "microscopic fluctuations" and observability of the effects of the Burnett and super-Burnett "corrections." The latter features may also exist in atomic fluids but they are observable there only under extreme conditions. Clustering, collapse and a kinetic theory for rapid flows of dilute granular systems, including a derivation of boundary conditions, are described alongside the mesoscopic properties of these systems with emphasis on the effects, theoretical conclusions and restrictions imposed by the lack of scale separation. (c) 1999 American Institute of Physics.

  1. Numerical modeling of geophysical granular flows: 1. A comprehensive approach to granular rheologies and geophysical multiphase flows

    Science.gov (United States)

    Dartevelle, SéBastien

    2004-08-01

    Geophysical granular materials display a wide variety of behaviors and features. Typically, granular flows (1) are multiphase flows, (2) are very dissipative over many different scales, (3) display a wide range of grain concentrations, and (4), as a final result of these previous features, display complex nonlinear, nonuniform, and unsteady rheologies. Therefore the objectives of this manuscript are twofold: (1) setting up a hydrodynamic model which acknowledges the multiphase nature of granular flows and (2) defining a comprehensive rheological model which accounts for all the different forms of viscous dissipations within granular flows at any concentration. Hence three important regimes within granular flows must be acknowledged: kinetic (pure free flights of grain), kinetic-collisional, and frictional. The momentum and energy transfer will be different according to the granular regimes, i.e., strain rate dependent in the kinetic and kinetic-collisional cases and strain rate independent in the frictional case. A "universal" granular rheological model requires a comprehensive unified stress tensor able to adequately describe viscous stress within the flow for any of these regimes, and without imposing a priori what regime will dominate over the others. The kinetic-collisional viscous regime is defined from a modified Boltzmann's kinetic theory of dense gas. The frictional viscous regime is defined from the plastic potential and the critical state theories which account for compressibility of granular matter (e.g., dilatancy, consolidation, and critical state). In the companion paper [, 2004] we will introduce a multiphase computer code, (G)MFIX, which accounts for all the granular regimes and rheology and present typical simulations of diluted (e.g., plinian clouds) and concentrated geophysical granular flows (i.e., pyroclastic flows and surges).

  2. State-to-state vibrational kinetics of H$_2$ and H$_2^+$ in a post-shock cooling gas with primordial composition

    CERN Document Server

    Coppola, C M; Bruno, D; Esposito, F; Galli, D; Palla, F; Longo, S

    2016-01-01

    The radiative cooling of shocked gas with primordial chemical composition is an important process relevant to the formation of the first stars and structures, as well as taking place also in high velocity cloud collisions and supernovae explosions. Among the different processes that need to be considered, the formation kinetics and cooling of molecular hydrogen are of prime interest, since they provide the only way to lower the gas temperature to values well below $\\sim$10$^4$~K. In previous works, the internal energy level structure of H$_2$ and its cation has been treated in the approximation of rovibrational ground state at low densities, or trying to describe the dynamics using some arbitrary $v>0$ H$_2$ level that is considered representative of the excited vibrational manifold. In this study, we compute the vibrationally resolved kinetics for the time-dependent chemical and thermal evolution of the post-shock gas in a medium of primordial composition. The calculated non-equilibrium distributions are use...

  3. THE COMPONENT TEST FACILITY – A NATIONAL USER FACILITY FOR TESTING OF HIGH TEMPERATURE GAS-COOLED REACTOR (HTGR) COMPONENTS AND SYSTEMS

    Energy Technology Data Exchange (ETDEWEB)

    David S. Duncan; Vondell J. Balls; Stephanie L. Austad

    2008-09-01

    The Next Generation Nuclear Plant (NGNP) and other High-Temperature Gas-cooled Reactor (HTGR) Projects require research, development, design, construction, and operation of a nuclear plant intended for both high-efficiency electricity production and high-temperature industrial applications, including hydrogen production. During the life cycle stages of an HTGR, plant systems, structures and components (SSCs) will be developed to support this reactor technology. To mitigate technical, schedule, and project risk associated with development of these SSCs, a large-scale test facility is required to support design verification and qualification prior to operational implementation. As a full-scale helium test facility, the Component Test facility (CTF) will provide prototype testing and qualification of heat transfer system components (e.g., Intermediate Heat Exchanger, valves, hot gas ducts), reactor internals, and hydrogen generation processing. It will perform confirmation tests for large-scale effects, validate component performance requirements, perform transient effects tests, and provide production demonstration of hydrogen and other high-temperature applications. Sponsored wholly or in part by the U.S. Department of Energy, the CTF will support NGNP and will also act as a National User Facility to support worldwide development of High-Temperature Gas-cooled Reactor technologies.

  4. Hydrodynamic modelling of dense gas-fluidised beds: comparison of the kinetic theory of granular flow with 3D hard-sphere discrete particle simulations

    NARCIS (Netherlands)

    Goldschmidt, M.J.V.; Beetstra, R.; Kuipers, J.A.M.

    2002-01-01

    A novel technique to sample particle velocity distributions and collision characteristics from dynamic discrete particle simulations of intrinsically unsteady, non-homogeneous systems, such as those encountered in dense gas-fluidised beds, is presented. The results are compared to the isotropic Maxw

  5. Rhapsody-G simulations I: the cool cores, hot gas and stellar content of massive galaxy clusters

    CERN Document Server

    Hahn, Oliver; Wu, Hao-Yi; Evrard, August E; Teyssier, Romain; Wechsler, Risa H

    2015-01-01

    We present the Rhapsody-G suite of cosmological hydrodynamic AMR zoom simulations of ten massive galaxy clusters at the $M_{\\rm vir}\\sim10^{15}\\,{\\rm M}_\\odot$ scale. These simulations include cooling and sub-resolution models for star formation and stellar and supermassive black hole feedback. The sample is selected to capture the whole gamut of assembly histories that produce clusters of similar final mass. We present an overview of the successes and shortcomings of such simulations in reproducing both the stellar properties of galaxies as well as properties of the hot plasma in clusters. In our simulations, a long-lived cool-core/non-cool core dichotomy arises naturally, and the emergence of non-cool cores is related to low angular momentum major mergers. Nevertheless, the cool-core clusters exhibit a low central entropy compared to observations, which cannot be alleviated by thermal AGN feedback. For cluster scaling relations we find that the simulations match well the $M_{500}-Y_{500}$ scaling of Planck ...

  6. Performance of cooling capacity adjustment in gas engine-driven heat pump%燃气机热泵容量调节制冷性能试验

    Institute of Scientific and Technical Information of China (English)

    王明涛; 刘焕卫; 张百浩

    2015-01-01

    Gas engine driven heat pump (GEHP), which mainly consists of a gas engine, an evaporator, a condenser and an expansion valve, can make full use of the waste heat from cylinder jacket and exhaust gas and achieve a higher primary energy ratio (PER) than other forms of heating/cooling systems, and therefore has been considered as a preferable choice in the air-conditioning scheme. Compared with the electric-driven heat pump (EHP), the GEHP has two distinguished advantages: 1) the ability to recover the gas engine waste heat from cylinder jacket and exhaust gas; 2) easy modulation of gas engine speed to meet the cooling loads. In the present article, a novel GEHP which could independently provide heating, cooling and hot water for the buildings was presented. The capacity adjustment and stable operation of GEHP could be achieved by controlling engine rotary speed. The goals of engine rotary speed control were to match the rotary speed and cooling/heating capacity, and keep robust to disturbance. In order to control engine rotary speed effectively, the engine rotary speed expert proportion-integration-differentiation (PID) controller was designed according to the engine rotary speed control knowledge base and the controlling rules in this study. Meanwhile, the energy analysis of GEHP was presented as well as the GEHP operating parameters (such as ambient air temperature, evaporator water flow and engine rotary speed). The engine rotary expert PID controller was applied to the engine rotary speed control in a GEHP system experimentally under different conditions (modulation on cooling loads and anti-disturbance), and the cooling performance characteristics of GEHP were investigated experimentally over a wide range of engine rotary speed (1 400-2 200 r/min). The performance of GEHP was characterized by cooling capacity, waste heat amount recovered, coefficient of performance (COP) and PER. The relationships between engine rotary speed and cooling capacity, waste heat

  7. METAL-POOR, COOL GAS IN THE CIRCUMGALACTIC MEDIUM OF A z = 2.4 STAR-FORMING GALAXY: DIRECT EVIDENCE FOR COLD ACCRETION?

    Energy Technology Data Exchange (ETDEWEB)

    Crighton, Neil H. M.; Hennawi, Joseph F. [Max-Planck-Institut für Astronomie, Königstuhl 17, Heidelberg D-69117 (Germany); Prochaska, J. Xavier, E-mail: neilcrighton@gmail.com [Department of Astronomy and Astrophysics, UCO/Lick Observatory, University of California, 1156 High Street, Santa Cruz, CA 95064 (United States)

    2013-10-20

    In our current galaxy formation paradigm, high-redshift galaxies are predominantly fueled by accretion of cool, metal-poor gas from the intergalactic medium. Hydrodynamical simulations predict that this material should be observable in absorption against background sightlines within a galaxy's virial radius, as optically thick Lyman limit systems (LLSs) with low metallicities. Here we report the discovery of exactly such a strong metal-poor absorber at an impact parameter R = 58 kpc from a star-forming galaxy at z = 2.44. Besides strong neutral hydrogen (N{sub H{sup 0}}=10{sup 19.50±0.16} cm{sup -2}) we detect neutral deuterium and oxygen, allowing a precise measurement of the metallicity: log{sub 10}(Z/Z {sub ☉}) = –2.0 ± 0.17, or (7-15) × 10{sup –3} solar. Furthermore, the narrow deuterium linewidth requires a cool temperature <20,000 K. Given the striking similarities between this system and the predictions of simulations, we argue that it represents the direct detection of a high-redshift cold-accretion stream. The low-metallicity gas cloud is a single component of an absorption system exhibiting a complex velocity, ionization, and enrichment structure. Two other components have metallicities >0.1 solar, 10 times larger than the metal-poor component. We conclude that the photoionized circumgalactic medium (CGM) of this galaxy is highly inhomogeneous: the majority of the gas is in a cool, metal-poor and predominantly neutral phase, but the majority of the metals are in a highly ionized phase exhibiting weak neutral hydrogen absorption but strong metal absorption. If such inhomogeneity is common, then high-resolution spectra and detailed ionization modeling are critical to accurately appraise the distribution of metals in the high-redshift CGM.

  8. rhapsody-g simulations - I. The cool cores, hot gas and stellar content of massive galaxy clusters

    Science.gov (United States)

    Hahn, Oliver; Martizzi, Davide; Wu, Hao-Yi; Evrard, August E.; Teyssier, Romain; Wechsler, Risa H.

    2017-09-01

    We present the rhapsody-g suite of cosmological hydrodynamic zoom simulations of 10 massive galaxy clusters at the Mvir ∼ 1015 M⊙ scale. These simulations include cooling and subresolution models for star formation and stellar and supermassive black hole feedback. The sample is selected to capture the whole gamut of assembly histories that produce clusters of similar final mass. We present an overview of the successes and shortcomings of such simulations in reproducing both the stellar properties of galaxies as well as properties of the hot plasma in clusters. In our simulations, a long-lived cool-core/non-cool-core dichotomy arises naturally, and the emergence of non-cool cores is related to low angular momentum major mergers. Nevertheless, the cool-core clusters exhibit a low central entropy compared to observations, which cannot be alleviated by thermal active galactic nuclei feedback. For cluster scaling relations, we find that the simulations match well the M500-Y500 scaling of Planck Sunyaev-Zeldovich clusters but deviate somewhat from the observed X-ray luminosity and temperature scaling relations in the sense of being slightly too bright and too cool at fixed mass, respectively. Stars are produced at an efficiency consistent with abundance-matching constraints and central galaxies have star formation rates consistent with recent observations. While our simulations thus match various key properties remarkably well, we conclude that the shortcomings strongly suggest an important role for non-thermal processes (through feedback or otherwise) or thermal conduction in shaping the intracluster medium.

  9. Rhapsody-G simulations I: the cool cores, hot gas and stellar content of massive galaxy clusters

    Science.gov (United States)

    Hahn, Oliver; Martizzi, Davide; Wu, Hao-Yi; Evrard, August E.; Teyssier, Romain; Wechsler, Risa H.

    2017-01-01

    We present the RHAPSODY-G suite of cosmological hydrodynamic AMR zoom simulations of ten massive galaxy clusters at the Mvir ˜ 1015 M⊙ scale. These simulations include cooling and sub-resolution models for star formation and stellar and supermassive black hole feedback. The sample is selected to capture the whole gamut of assembly histories that produce clusters of similar final mass. We present an overview of the successes and shortcomings of such simulations in reproducing both the stellar properties of galaxies as well as properties of the hot plasma in clusters. In our simulations, a long-lived cool-core/non-cool core dichotomy arises naturally, and the emergence of non-cool cores is related to low angular momentum major mergers. Nevertheless, the cool-core clusters exhibit a low central entropy compared to observations, which cannot be alleviated by thermal AGN feedback. For cluster scaling relations we find that the simulations match well the M500 - Y500 scaling of Planck SZ clusters but deviate somewhat from the observed X-ray luminosity and temperature scaling relations in the sense of being slightly too bright and too cool at fixed mass, respectively. Stars are produced at an efficiency consistent with abundance matching constraints and central galaxies have star formation rates consistent with recent observations. While our simulations thus match various key properties remarkably well, we conclude that the shortcomings strongly suggest an important role for non-thermal processes (through feedback or otherwise) or thermal conduction in shaping the intra-cluster medium.

  10. High-temperature gas-cooled reactor safety studies. Progress report for January 1, 1974--June 30, 1975

    Energy Technology Data Exchange (ETDEWEB)

    Cole, T.E.; Sanders, J.P.; Kasten, P.R.

    1977-07-01

    Progress is reported in the following areas: systems and safety analysis; fission product technology; primary coolant technology; seismic and vibration technology; confinement components; primary system materials technology; safety instrumentation; loss of flow accident analysis using HEATUP code; use of coupled-conduction-convection model for core thermal analysis; development of multichannel conduction-convection program HEXEREI; cooling system performance after shutdown; core auxiliary cooling system performance; development of FLODIS code; air ingress into primary systems following DBDA; performance of PCRV thermal barrier cover plates; temperature limits for fuel particle coating failure; tritium distribution and release in HTGR; energy release to PCRV during DBDA; and mathematical models for HTGR reactor safety studies.

  11. Recent Development of Air-Cooled Bainitic Steels Containing Manganese

    Institute of Scientific and Technical Information of China (English)

    FANG Hong-sheng; YANG Fu-bao; BAI Bing-zhe; YANG Zhi-gang; YIN Jiang

    2005-01-01

    The superiorities of air-cooled bainitic steels were described.A series of air-cooled bainitic steels containing manganese were developed and presented,which include low carbon granular bainitic steels,low carbon grain-boundary allotriomorphic ferrite/granular bainite dual phase steels,medium and medium high carbon bainite/martensite dual phase steels and casting bainitic steels.The development of ultra-low carbon bainitic steels in China was also introduced.

  12. Effect of electricity tariffs and cooling technologies on dairy farm electricity consumption, related costs and greenhouse gas emissions

    NARCIS (Netherlands)

    Upton, J.R.; Shalloo, L.; Murphy, M.; Groot Koerkamp, P.W.G.; Boer, de I.J.M.

    2014-01-01

    The aim of this study was to provide insight into the variations in dairy farm electricity costs across five electricity tariffs. The effect of four milk cooling scenarios is also simulated to illustrate the effect of technologies on the electricity consumption, related costs and CO2 emissions of a

  13. Effect of electricity tariffs and cooling technologies on dairy farm electricity consumption, related costs and greenhouse gas emissions

    NARCIS (Netherlands)

    Upton, J.R.; Shalloo, L.; Murphy, M.; Groot Koerkamp, P.W.G.; Boer, de I.J.M.

    2014-01-01

    The aim of this study was to provide insight into the variations in dairy farm electricity costs across five electricity tariffs. The effect of four milk cooling scenarios is also simulated to illustrate the effect of technologies on the electricity consumption, related costs and CO2 emissions of a

  14. Similitude study of a moving bed granular filter

    Energy Technology Data Exchange (ETDEWEB)

    Robert C. Brown; Huawei Shi; Gerald Colver; Saw-Choon Soo [Iowa State University, IA (United States)

    2003-12-10

    The goal of this study was to evaluate the performance of a moving bed granular filter designed for hot gas clean up. This study used similitude theory to devise experiments that were conducted at near-ambient conditions while simulating the performance of filters operated at elevated temperatures and pressures (850{sup o}C and 1000 kPa). These experiments revealed that the proposed moving bed granular filter can operate at high collection efficiencies, typically exceeding 99%, and low pressure drops without the need for periodic regeneration through the use of a continuous flow of fresh granular filter media in the filter. In addition, important design constraints were discovered for the successful operation of the proposed moving bed granular filter.

  15. Early Science with the Large Millimeter Telescope: COOL BUDHIES I - a pilot study of molecular and atomic gas at z ≃ 0.2

    Science.gov (United States)

    Cybulski, Ryan; Yun, Min S.; Erickson, Neal; De la Luz, Victor; Narayanan, Gopal; Montaña, Alfredo; Sánchez, David; Zavala, Jorge A.; Zeballos, Milagros; Chung, Aeree; Fernández, Ximena; van Gorkom, Jacqueline; Haines, Chris P.; Jaffé, Yara L.; Montero-Castaño, María; Poggianti, Bianca M.; Verheijen, Marc A. W.; Yoon, Hyein; Deshev, Boris Z.; Harrington, Kevin; Hughes, David H.; Morrison, Glenn E.; Schloerb, F. Peter; Velazquez, Miguel

    2016-07-01

    An understanding of the mass build-up in galaxies over time necessitates tracing the evolution of cold gas (molecular and atomic) in galaxies. To that end, we have conducted a pilot study called CO Observations with the LMT of the Blind Ultra-Deep H I Environment Survey (COOL BUDHIES). We have observed 23 galaxies in and around the two clusters Abell 2192 (z = 0.188) and Abell 963 (z = 0.206), where 12 are cluster members and 11 are slightly in the foreground or background, using about 28 total hours on the Redshift Search Receiver on the Large Millimeter Telescope (LMT) to measure the 12CO J = 1 → 0 emission line and obtain molecular gas masses. These new observations provide a unique opportunity to probe both the molecular and atomic components of galaxies as a function of environment beyond the local Universe. For our sample of 23 galaxies, nine have reliable detections (S/N ≥ 3.6) of the 12CO line, and another six have marginal detections (2.0 < S/N < 3.6). For the remaining eight targets we can place upper limits on molecular gas masses roughly between 109 and 1010 M⊙. Comparing our results to other studies of molecular gas, we find that our sample is significantly more abundant in molecular gas overall, when compared to the stellar and the atomic gas component, and our median molecular gas fraction lies about 1σ above the upper limits of proposed redshift evolution in earlier studies. We discuss possible reasons for this discrepancy, with the most likely conclusion being target selection and Eddington bias.

  16. Possibility of a gas-cooled Peltier current lead in the 200 m-class superconducting direct current transmission and distribution system of CASER-2

    Science.gov (United States)

    Kawahara, Toshio; Emoto, Masahiko; Watanabe, Hirofumi; Hamabe, Makoto; Yamaguchi, Sataro; Hikichi, Yasuo; Minowa, Masahiro

    Global energy problems should be solved quickly, and superconducting applications are highly demanded as energy saving technologies. Among them, long-distance superconducting transmission seems to be one of the most promising for energy saving by energy sharing. On the other hand, such large systems can be constructed from smaller network systems that can be enhanced by scaling up to the superconducting grid. Reducing heat leak to the low temperature end is the most important aspect of technology for practical superconducting applications, and heat leak reduction at the terminal is a key goal especially for small-length applications. At Chubu University, we have developed a 200 m-class superconducting direct current transmission and distribution system (CASER-2), in which we also used a Peltier current lead (PCL) as heat insulation at the terminal. PCL is composed of a thermoelectric material and a copper lead. In actual transmission and distribution applications, the cables are also cooled by the coolant. After the circulation, the coolant could also be used to cool the current lead. We will discuss the performance of such gas-cooled systems as the total performance of applied superconducting systems using the experimental parameters obtained in CASER-2.

  17. Effect of cooled EGR on performance and exhaust gas emissions in EFI spark ignition engine fueled by gasoline and wet methanol blends

    Science.gov (United States)

    Rohadi, Heru; Syaiful, Bae, Myung-Whan

    2016-06-01

    Fuel needs, especially the transport sector is still dominated by fossil fuels which are non-renewable. However, oil reserves are very limited. Furthermore, the hazardous components produced by internal combustion engine forces many researchers to consider with alternative fuel which is environmental friendly and renewable sources. Therefore, this study intends to investigate the impact of cooled EGR on the performance and exhaust gas emissions in the gasoline engine fueled by gasoline and wet methanol blends. The percentage of wet methanol blended with gasoline is in the range of 5 to 15% in a volume base. The experiment was performed at the variation of engine speeds from 2500 to 4000 rpm with 500 intervals. The re-circulated exhaust gasses into combustion chamber was 5%. The experiment was performed at the constant engine speed. The results show that the use of cooled EGR with wet methanol of 10% increases the brake torque up to 21.3%. The brake thermal efficiency increases approximately 39.6% using cooled EGR in the case of the engine fueled by 15% wet methanol. Brake specific fuel consumption for the engine using EGR fueled by 10% wet methanol decreases up to 23% at the engine speed of 2500 rpm. The reduction of CO, O2 and HC emissions was found, while CO2 increases.

  18. Component testing of a ground based gas turbine steam cooled rich-burn primary zone combustor for emissions control of nitrogeneous fuels

    Science.gov (United States)

    Schultz, D. F.

    1986-01-01

    This effort summarizes the work performed on a steam cooled, rich-burn primary zone, variable geometry combustor designed for combustion of nitrogeneous fuels such as heavy oils or synthetic crude oils. The steam cooling was employed to determine its feasibility and assess its usefulness as part of a ground based gas turbine bottoming cycle. Variable combustor geometry was employed to demonstrate its ability to control primary and secondary zone equivalence ratios and overall pressure drop. Both concepts proved to be highly successful in achieving their desired objectives. The steam cooling reduced peak liner temperatures to less than 800 K. This low temperature offers the potential of both long life and reduced use of strategic materials for liner fabrication. These degrees of variable geometry were successfully employed to control air flow distribution within the combustor. A variable blade angle axial flow air swirler was used to control primary zone air flow, while the secondary and tertiary zone air flows were controlled by rotating bands which regulated air flow to the secondary zone quench holes and the dilutions holes respectively.

  19. CFD Analysis for Flow Behavior Characteristics in the Upper Plenum during low flow/low pressure transients for the Gas Cooled Fast Reactor (GCFR)

    Energy Technology Data Exchange (ETDEWEB)

    Piyush Sabharwall; Theron Marshall; Kevan Weaver; Hans Gougar

    2007-05-01

    Gas coolant at low pressure exhibits poor heat transfer characteristics. This is an area of concern for the passive response targeted by the Generation IV GCFR design. For the first 24 hour period, the decay heat removal for the GCFR design is dependent on an actively powered blower, which also would reduce the temperature in the fuel during transients, before depending on the passive operation. Natural circulation cooling initiates when the blower is stopped for the final phase of the decay heat removal, as under forced convection the core decay heat is adequately cooled by the running blower. The ability of the coolant to flow in the reverse direction or having recirculation, when the blowers are off, necessitates more understanding of the flow behavior characteristics in the upper plenum. The work done here focuses primarily on the period after the blower has been turned off, as the core is adequately cooled when the blowers are running, thus there was no need to carry out the analysis for the first 24 hours. In order to understand the plume behavior for the GCFR upper plenum several cases were run, with air, helium and helium-air mixture. For each case, the FLUENT was used to characterize the steady state velocity vectors and corresponding temperature in the upper plenum under passive decay heat removal conditions. This study will provide better insight into the plume interaction in the upper plenum at low flow and low pressure conditions.

  20. Granular dampers: does particle shape matter?

    Science.gov (United States)

    Pourtavakoli, Hamzeh; Parteli, Eric J. R.; Pöschel, Thorsten

    2016-07-01

    By means of particle-based numerical simulations using the discrete element method, we address the question of how the performance of granular dampers is affected by the shape of the granular particles. In consistence with previous experiments performed with nearly spherical particles we find that independently of the particles’ shape, the granular system is characterized by a gas-like regime for small amplitudes of the container’s oscillation and by a collect-and-collide regime for large amplitude forcing. Both regimes are separated by an optimal operation mode—the critical amplitude of the damping oscillation for which the energy dissipation is maximal—which is independent of the particle shape for given conditions of particle mass, material properties and number of particles. However, in the gas-like regime, we find that spherical particles lead to more efficient energy dissipation compared to complex shaped particles of the same mass. In this regime, a dependence on the damper’s efficiency on the particle shape is found.

  1. Nucleation, aggregation, annealing, and disintegration of granular clusters

    Science.gov (United States)

    González-Gutiérrez, Jorge; Carrillo-Estrada, J. L.; Ruiz-Suárez, J. C.

    2014-05-01

    The processes of nucleation, aggregation, annealing, and disintegration of clusters of non-Brownian paramagnetic beads in a vibrofluidized system are experimentally investigated. The interaction among the beads is induced by a magnetic seed composed of two dipoles allocated outside the container cell. We observe a clearly differentiated nucleation stage, whose evolution (nucleation time versus acceleration strength) follows a power law. Thereafter, the beads aggregate forming 2D disordered clusters around the nucleus. Both processes (nucleation and aggregation) are determined by the competition between magnetic forces and the drag produced by a thermal bath created by glass particles. Once the agglomerates reach a final state (shape and length), they are annealed by increasing and decreasing the granular temperature. We found that the fractal dimension and the lacunarity index clearly describe the structural variations of the clusters. Our discussion on this phenomenon is addressed, making a rough analogy with the glass transition in a super-cooled liquid. Finally, we study the disintegration of the clusters as a function of time and the density of the surrounding gas. The question is not if, but how they disintegrate upon removing the external field; we find that the disintegration follows an exponential decay.

  2. Mutiscale Modeling of Segregation in Granular Flows

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Jin [Iowa State Univ., Ames, IA (United States)

    2007-01-01

    Modeling and simulation of segregation phenomena in granular flows are investigated. Computational models at different scales ranging from particle level (microscale) to continuum level (macroscale) are employed in order to determine the important microscale physics relevant to macroscale modeling. The capability of a multi-fluid model to capture segregation caused by density difference is demonstrated by simulating grain-chaff biomass flows in a laboratory-scale air column and in a combine harvester. The multi-fluid model treats gas and solid phases as interpenetrating continua in an Eulerian frame. This model is further improved by incorporating particle rotation using kinetic theory for rapid granular flow of slightly frictional spheres. A simplified model is implemented without changing the current kinetic theory framework by introducing an effective coefficient of restitution to account for additional energy dissipation due to frictional collisions. The accuracy of predicting segregation rate in a gas-fluidized bed is improved by the implementation. This result indicates that particle rotation is important microscopic physics to be incorporated into the hydrodynamic model. Segregation of a large particle in a dense granular bed of small particles under vertical. vibration is studied using molecular dynamics simulations. Wall friction is identified as a necessary condition for the segregation. Large-scale force networks bearing larger-than-average forces are found with the presence of wall friction. The role of force networks in assisting rising of the large particle is analyzed. Single-point force distribution and two-point spatial force correlation are computed. The results show the heterogeneity of forces and a short-range correlation. The short correlation length implies that even dense granular flows may admit local constitutive relations. A modified minimum spanning tree (MST) algorithm is developed to asymptotically recover the force statistics in the

  3. Prediction calculations and experiments for the first criticality of the 10 MW High Temperature Gas-cooled Reactor-Test Module

    Energy Technology Data Exchange (ETDEWEB)

    Jing Xingqing E-mail: jingxq@d103.inet.tsinghua.edu.cn; Xu Xiaolin; Yang Yongwei; Qu Ronghong

    2002-10-01

    The 10 MW High Temperature Gas-cooled Reactor-Test Module (HTR-10) is a pebble bed experimental reactor built by the Institute of Nuclear Energy Technology (INET), Tsinghua University. This paper introduces the first critical prediction calculations and the experiments for the HTR-10. The German VSOP neutronics code is used for the prediction calculations of the first loading. The characteristics of pebble-bed high temperature gas-cooled reactors are taken into account, including the double heterogeneity of the fuel element, the buckling feedback of the spectrum calculation, the effect of the mixture of fuel elements and graphite balls, and the correction of the diffusion coefficients in the upper cavity based on transport theory. Also considered are the effects of impurities in the fuel elements, in the graphite balls and in the reflector graphite on the reactivity. The number of fuel elements and graphite balls in the initial core is predicted to provide reference for the first criticality experiment. The critical experiment adopts a method of extrapolating to approach criticality. The first criticality was attained on December 1, 2000. The first criticality experiment shows that the predicted critical number of the fuel elements and graphite balls is in close agreement with the experimental results. Their relative error is less than 1.0%, implying the physical predictions and the results of the criticality experiment are much beyond expectations.

  4. Analysis of the energetic/environmental performances of gas turbine plant: Effect of thermal barrier coatings and mass of cooling air

    Directory of Open Access Journals (Sweden)

    Ion Ion V.

    2009-01-01

    Full Text Available Zirconia stabilized with 8 wt.% Y2O3 is the most common material to be applied in thermal barrier coatings owing to its excellent properties: low thermal conductivity, high toughness and thermal expansion coefficient as ceramic material. Calculation has been made to evaluate the gains of thermal barrier coatings applied on gas turbine blades. The study considers a top ceramic coating Zirconia stabilized with 8 wt.% Y2O3 on a NiCoCrAlY bond coat and Inconel 738LC as substrate. For different thickness and different cooling air flow rates, a thermodynamic analysis has been performed and pollutants emissions (CO, NOx have been estimated to analyze the effect of rising the gas inlet temperature. The effect of thickness and thermal conductivity of top coating and the mass flow rate of cooling air have been analyzed. The model for heat transfer analysis gives the temperature reduction through the wall blade for the considered conditions and the results presented in this contribution are restricted to a two considered limits: (1 maximum allowable temperature for top layer (1200ºC and (2 for blade material (1000ºC. The model can be used to analyze other materials that support higher temperatures helping in the development of new materials for thermal barrier coatings.

  5. Buffer-gas cooling of antiprotonic helium to 1.5 to 1.7 K, and antiproton-to–electron mass ratio

    CERN Document Server

    Hori, Masaki; Sótér, Anna; Barna, Daniel; Dax, Andreas; Hayano, Ryugo; Kobayashi, Takumi; Murakami, Yohei; Todoroki, Koichi; Yamada, Hiroyuki; Horváth, Dezső; Venturelli, Luca

    2016-01-01

    Charge, parity, and time reversal (CPT) symmetry implies that a particle and its antiparticle have the same mass. The antiproton-to-electron mass ratio Embedded Image can be precisely determined from the single-photon transition frequencies of antiprotonic helium. We measured 13 such frequencies with laser spectroscopy to a fractional precision of 2.5 × 10−9 to 16 × 10−9. About 2 × 109 antiprotonic helium atoms were cooled to temperatures between 1.5 and 1.7 kelvin by using buffer-gas cooling in cryogenic low-pressure helium gas; the narrow thermal distribution led to the observation of sharp spectral lines of small thermal Doppler width. The deviation between the experimental frequencies and the results of three-body quantum electrodynamics calculations was reduced by a factor of 1.4 to 10 compared with previous single-photon experiments. From this, Embedded Image was determined as 1836.1526734(15), which agrees with a recent proton-to-electron experimental value within 8 × 10−10.

  6. Velocity distributions in dilute granular systems.

    Science.gov (United States)

    van Zon, J S; MacKintosh, F C

    2005-11-01

    We investigate the idea that velocity distributions in granular gases are determined mainly by eta, the coefficient of restitution and q, which measures the relative importance of heating (or energy input) to collisions. To this end, we study by numerical simulation the properties of inelastic gases as functions of eta, concentration phi, and particle number N with various heating mechanisms. For a wide range of parameters, we find Gaussian velocity distributions for uniform heating and non-Gaussian velocity distributions for boundary heating. Comparison between these results and velocity distributions obtained by other heating mechanisms and for a simple model of a granular gas without spatial degrees of freedom, shows that uniform and boundary heating can be understood as different limits of q, with q>1 and q < or approximately 1 respectively. We review the literature for evidence of the role of q in the recent experiments.

  7. Performance and evaluation of gas engine driven rooftop air conditioning equipment at the Willow Grove (PA) Naval Air Station. Interim report, 1992 cooling season

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, P.R.; Conover, D.R.

    1993-05-01

    In a field evaluation conducted for the US Department of Energy (DOE) Office of Federal Energy Management Program (FEMP), the Pacific Northwest Laboratory (PNL) examined the performance of a new US energy-related technology under the FEMP Test Bed Demonstration Program. The technology was a 15-ton natural gas engine driven roof top air conditioning unit. Two such units were installed on a naval retail building to provide space conditioning to the building. Under the Test Bed Demonstration Program, private and public sector interests are focused to support the installation and evaluation of new US technologies in the federal sector. Participating in this effort under a Cooperative Research and Development Agreement (CRADA) with DOE were the American Gas Cooling Center, Philadelphia Electric Company, Thermo King Corporation, and the US Naval Air Station at Willow Grove, Pennsylvania. Equipment operating and service data as well as building interior and exterior conditions were secured for the 1992 cooling season. Based on a computer assessment of the building using standard weather data, a comparison was made with the energy and operating costs associated with the previous space conditioning system. Based on performance during the 1992 cooling season and adjusted to a normal weather year, the technology will save the site $6,000/yr in purchased energy costs. An additional $9,000 in savings due to electricity demand ratchet charge reductions will also be realized. Detailed information on the technology, the installation, and the results of the technology test are provided to illustrate the advantages to the federal sector of using this technology. A history of the CRADA development process is also reported.

  8. Studi Numerik Peningkatan Cooling Performance pada Lube Oil Cooler Gas Turbine yang Disusun Secara Seri dan Paralel dengan Variasi Kapasitas Aliran Lube Oil

    Directory of Open Access Journals (Sweden)

    Annis Khoiri Wibowo

    2014-09-01

    Full Text Available Salah satu komponen pada gas turbine adalah lube oil cooler yang berfungsi sebagai heat exchanger untuk mendinginkan temperatur lube oil. Pemasangan tiga lube oil cooler type-Z compact heat exchanger pada susunan seri dan paralel berdampak pada cooling capacity lube oil cooler. Uniformity flow rate pada masing-masing tube merupakan salah satu faktor yang mempengaruhi cooling capacity dari lube oil coole. Oleh karena itu dilakukan simulasi Computational Fluid Dynamic (CFD untuk mengkaji pengaruh pemasangan susunan tiga lube oil cooler secara seri dan paralel dengan variasi kapasitas lube oil terhadap performance lube oil cooler. Pemodelan domain dilakukan dengan 3 dimensi pada sisi eksternal dan internal. Simulasi pada sisi eksternal dilakukan untuk memperoleh nilai koefisien heat transfer pada masing-masing baris tube. Selanjutnya, nilai koefisien heat transfer yang didapat pada sisi eksternal digunakan sebagai kondisi batas wall convection pada masing-masing baris tube untuk simulasi internal flow dengan variasi flow rate lube oil 30 gpm, 50 gpm, 74 gpm. Dari hasil simulasi, susunan cooler seri menghasilkan cooling capacity yang lebih baik dari pada susunan cooler paralel pada kapasitas lube oil yang sama. Hal tersebut terjadi karena flow ratio lube oil untuk masing-masing tube pada susunan cooler seri lebih seragam dari pada susunan cooler paralel. Keseragaman flow rate pada masing-masing tube ditunjukkan dengan kecilnya standard deviasi flow ratio. Kapasitas 50 gpm memiliki standard deviasi flow ratio sebesar 0,46 untuk susunan seri dan 0,75 untuk susunan paralel. Semakin besar kapasitas lube oil maka distribusi flow rate pada masing-masing tube semakin tidak seragam. Selain itu susunan cooler seri memiliki pressure drop yang lebih besar dari pada susunan cooler paralel. Pemasangan susunan cooler dengan kapasitas 30 gpm memiliki tingkat keseragaman yang paling tinggi ditunjukkan dengan standard deviasi flow ratio pada masing-masing tube yang

  9. Heat transfer performance comparison of steam and air in gas turbine cooling channels with different rib angles

    Science.gov (United States)

    Shi, Xiaojun; Gao, Jianmin; Xu, Liang; Li, Fajin

    2013-11-01

    Using steam as working fluid to replace compressed air is a promising cooling technology for internal cooling passages of blades and vanes. The local heat transfer characteristics and the thermal performance of steam flow in wide aspect ratio channels ( W/ H = 2) with different angled ribs on two opposite walls have been experimentally investigated in this paper. The averaged Nusselt number ratios and the friction factor ratios of steam and air in four ribbed channels were also measured under the same test conditions for comparison. The Reynolds number range is 6,000-70,000. The rib angles are 90°, 60°, 45°, and 30°, respectively. The rib height to hydraulic diameter ratio is 0.047. The pitch-to-rib height ratio is 10. The results show that the Nusselt number ratios of steam are 1.19-1.32 times greater than those of air over the range of Reynolds numbers studied. For wide aspect ratio channels using steam as the coolant, the 60° angled ribs has the best heat transfer performance and is recommended for cooling design.

  10. The rise of granular computing

    Institute of Scientific and Technical Information of China (English)

    YAO Yi-yu

    2008-01-01

    This paper has two purposes. One is to present a critical examination of the rise of granular computing and the other is to suggest a triarchic theory of granular computing. By examining the reasons, justifications, and motivations for the rise of granular computing, we may be able to fully appreciate its scope, goal and potential values. The results enable us to formulate a triarchic theory in the light of research results from many disciplines. The three components of the theory are labeled as the philosophy, the methodology, and the computation. The integration of the three offers a unified view of gran-ular computing as a way of structured thinking, a method of structured problem solving, and a paradigm of structured infor-mation processing, focusing on hierarchical granular structures. The triarchic theory is an important effort in synthesizing the various theories and models of granular computing.

  11. Three Perspectives of Granular Computing

    Institute of Scientific and Technical Information of China (English)

    Yiyu(Y.Y.) Yao

    2006-01-01

    As an emerging field of study, granular computing has received much attention. Many models, frameorks, methods and techniques have been proposed and studied. It is perhaps the time to seek for a general and unified view so that fundamental issues can be examined and clarified. This paper examines granular computing from three perspectives. By viewing granular computing as a way of structured thinking,we focus on its philosophical foundations in modeling human perception of the reality. By viewing granular computing as a method of structured problem solving, we examine its theoretical and methodological foundations in solving a wide range of real-world problems. By viewing granular computing as a paradigm of information processing,we turn our attention to its more concrete techniques. The three perspectives together offer a holistic view of granular computing.

  12. Blow up Analysis for Anomalous Granular Gases

    OpenAIRE

    Rey, Thomas

    2012-01-01

    20 p.; International audience; We investigate in this article the long-time behaviour of the solutions to the energy-dependant, spatially-homogeneous, inelastic Boltzmann equation for hard spheres. This model describes a diluted gas composed of hard spheres under statistical description, that dissipates energy during collisions. We assume that the gas is ''anomalous'', in the sense that energy dissipation increases when temperature decreases. This allows the gas to cool down in finite time. W...

  13. Mathematical models of granular matter

    CERN Document Server

    Mariano, Paolo; Giovine, Pasquale

    2008-01-01

    Granular matter displays a variety of peculiarities that distinguish it from other appearances studied in condensed matter physics and renders its overall mathematical modelling somewhat arduous. Prominent directions in the modelling granular flows are analyzed from various points of view. Foundational issues, numerical schemes and experimental results are discussed. The volume furnishes a rather complete overview of the current research trends in the mechanics of granular matter. Various chapters introduce the reader to different points of view and related techniques. New models describing granular bodies as complex bodies are presented. Results on the analysis of the inelastic Boltzmann equations are collected in different chapters. Gallavotti-Cohen symmetry is also discussed.

  14. Type-2 fuzzy granular models

    CERN Document Server

    Sanchez, Mauricio A; Castro, Juan R

    2017-01-01

    In this book, a series of granular algorithms are proposed. A nature inspired granular algorithm based on Newtonian gravitational forces is proposed. A series of methods for the formation of higher-type information granules represented by Interval Type-2 Fuzzy Sets are also shown, via multiple approaches, such as Coefficient of Variation, principle of justifiable granularity, uncertainty-based information concept, and numerical evidence based. And a fuzzy granular application comparison is given as to demonstrate the differences in how uncertainty affects the performance of fuzzy information granules.

  15. Super Massive Star Clusters: From Superwinds to a Cooling Catastrophe and the Re-processing of the Injected Gas

    CERN Document Server

    Silich, S; Muñoz-Tunón, C; Palous, J

    2006-01-01

    Different hydrodynamic regimes for the gaseous outflows generated by multiple supernovae explosions and stellar winds occurring within compact and massive star clusters are discussed. It is shown that there exists the threshold energy that separates clusters whose outflows evolve in the quasi-adiabatic or radiative regime from those within which catastrophic cooling and a positive feedback star-forming mode sets in. The role of the surrounding ISM and the observational appearance of the star cluster winds evolving in different hydrodynamic regimes are also discussed.

  16. The effect of cold trap adsorbents on the gas chromatographic analysis of ambient VOCs under Peltier cooling conditions.

    Science.gov (United States)

    Pal, Raktim; Kim, Ki-Hyun

    2008-04-01

    In this work, the relative analytical performance of the GC-based detection method was investigated with a major focus on cold trap (CT) adsorbent materials against four aromatic volatile organic compounds (VOCs) (e. g., benzene, toluene, xylene, and styrene). A series of calibration experiments were hence conducted under cryofocusing conditions formed by the Peltier cooling system in a thermal desorber (TD) unit. During the course of this study, comparative calibration datasets were acquired for each of the three CT types: (i) CT (I) = Carbopack B + Carbopack C, (ii) CT (II) = Carbopack B + Carboxen 1000, and (iii) CT (III) = Tenax TA. All calibration datasets were obtained under subambient temperature (-10 degrees C) conditions controlled by the Peltier cooling system. The reliability of the calibration data was also assessed in an ancillary experiment with the aid of the modified injection through a thermal desorber (MITD) method. The results demonstrated that the GC detection properties of different VOCs were not altered significantly between different CT applications under Peltier conditions, although relative sensitivity could be distinguished moderately depending on the CT type.

  17. Local thermal resonance control of GaInP photonic crystal membrane cavities using ambient gas cooling

    Energy Technology Data Exchange (ETDEWEB)

    Sokolov, Sergei, E-mail: s.sokolov@utwente.nl; Lian, Jin; Yüce, Emre; Mosk, Allard P. [Complex Photonic Systems (COPS), MESA+ Institute for Nanotechnology, University of Twente, 7500 AE Enschede (Netherlands); Combrié, Sylvain; Lehoucq, Gaelle; De Rossi, Alfredo [Thales Research and Technology, Route Départementale 128, 91767 Palaiseau (France)

    2015-04-27

    We perform spatially dependent tuning of a GaInP photonic crystal cavity using a continuous wave violet laser. Local tuning is obtained by laser heating of the photonic crystal membrane. The cavity resonance shift is measured for different pump positions and for two ambient gases: He and N{sub 2}. We find that the width of the temperature profile induced in the membrane depends strongly on the thermal conductivity of the ambient gas. For He gas, a narrow spatial width of the temperature profile of 2.8 μm is predicted and verified in experiment.

  18. Advanced Gas Cooled Nuclear Reactor Materials Evaluation and Development Program. Progress report, January 1, 1978--March 31, 1978

    Energy Technology Data Exchange (ETDEWEB)

    1978-06-26

    The activities associated with the procurement of the materials for the screening test program, information from vendor certification for the materials received, and preliminary information from the materials characterization tests performed by GE are reported. The construction status of the simulated reactor helium supply system, testing equipment, and gas chemistry analysis instrumentation and equipment are discussed. The final recommended impurity levels for the screening phase helium are presented and the rational behind this gas chemistry is discussed. The status of the data management system is presented.

  19. Design and development of a propulsion system for a cubesat - Based on solid propellant cool gas generator technology

    NARCIS (Netherlands)

    Rackemann, N.J.; Sanders, H.M.; Vliet, L.D. van

    2006-01-01

    Orbital manoeuvring is the next challenge in the development of cubesats. In this study a propulsion system for a cubesat with the main purpose of providing orbit manoeuvring and formation flying has been designed. This propulsion system is basically a cold gas system but it does not use a pressuris

  20. Design and development of a propulsion system for a cubesat - Based on solid propellant cool gas generator technology

    NARCIS (Netherlands)

    Rackemann, N.J.; Sanders, H.M.; Vliet, L.D. van

    2006-01-01

    Orbital manoeuvring is the next challenge in the development of cubesats. In this study a propulsion system for a cubesat with the main purpose of providing orbit manoeuvring and formation flying has been designed. This propulsion system is basically a cold gas system but it does not use a pressuris