Green operations of belt conveyors by means of speed control

NARCIS (Netherlands)

He, D.; Pang, Y.; Lodewijks, G.

2017-01-01

Belt conveyors can be partially loaded due to the variation of bulk material flow loaded onto the conveyor. Speed control attempts to reduce the belt conveyor energy consumption and to enable the green operations of belt conveyors. Current research of speed control rarely takes the conveyor dynamics

Belt Conveyor Dynamic Characteristics and Influential Factors

Directory of Open Access Journals (Sweden)

Junxia Li

2018-01-01

Full Text Available This paper uses the Kelvin-Voigt viscoelastic model to establish the continuous dynamic equations for tail hammer tension belt conveyors. The viscoelastic continuity equations are solved using the generalized coordinate method. We analyze various factors influencing longitudinal vibration of the belt conveyor by simulation and propose a control strategy to limit the vibration. The proposed approach and control strategy were verified by several experimental researches and cases. The proposed approach provides improved accuracy for dynamic design of belt conveyors.

Speed Controlled Belt Conveyors: Drives and Mechanical Considerations

Directory of Open Access Journals (Sweden)

BEBIC, M. Z.

2018-02-01

Full Text Available The paper presents variable speed belt conveyor system where the reference speed is changed in order to achieve improved energy efficiency of operation. The recorded measurements show that belt tension varies within the same limits as under constant speed operation. These results introduce a new insight of the present state of the art in variable speed belt conveyor drives. The system is realized with remote control from the control center on an open pit mine. The structure of the multi-motor drive system of a single conveyor, as well as of the network-based control system distributed among belt conveyor stations and the control center are shown. Speed control of a belt conveyor system is organized to provide better utilization of the available material cross section on the belt and reduced electrical energy consumption of the drive. The experimental results obtained on the system prove that, under existing constraints, the applied algorithm has not introduced additional stress to the belt or mechanical assemblies during acceleration and deceleration processes, while providing higher energy efficiency of operation.

An Effective Belt Conveyor for Underground Ore Transportation Systems

Science.gov (United States)

Krol, Robert; Kawalec, Witold; Gladysiewicz, Lech

2017-12-01

Raw material transportation generates a substantial share of costs in the mining industry. Mining companies are therefore determined to improve the effectiveness of their transportation system, focusing on solutions that increase both its energy efficiency and reliability while keeping maintenance costs low. In the underground copper ore operations in Poland’s KGHM mines vast and complex belt conveyor systems have been used for horizontal haulage of the run-of-mine ore from mining departments to shafts. Basing upon a long-time experience in the field of analysing, testing, designing and computing of belt conveyor equipment with regard to specific operational conditions, the improvements to the standard design of an underground belt conveyor for ore transportation have been proposed. As the key elements of a belt conveyor, the energy-efficient conveyor belt and optimised carrying idlers have been developed for the new generation of underground conveyors. The proposed solutions were tested individually on the specially constructed test stands in the laboratory and in the experimental belt conveyor that was built up with the use of prototype parts and commissioned for the regular ore haulage in a mining department in the KGHM underground mine “Lubin”. Its work was monitored and the recorded operational parameters (loadings, stresses and strains, energy dissipation, belt tracking) were compared with those previously collected on a reference (standard) conveyor. These in-situ measurements have proved that the proposed solutions will return with significant energy savings and lower maintenance costs. Calculations made on the basis of measurement results in the specialized belt conveyor designing software allow to estimate the possible savings if the modernized conveyors supersede the standard ones in a large belt conveying system.

Transfer points of belt conveyors operating with unfavorable bulk

Energy Technology Data Exchange (ETDEWEB)

Goehring, H [Technische Universitaet, Dresden (German Democratic Republic)

1989-06-01

Describes design of belt conveyor chutes that transfer bulk of surface mines from one conveyor to another. Conveyor belt velocity is a significant parameter. Unfavorable chute design may lead to bulk flow congestion, bulk velocity losses etc. The bulk flow process is analyzed, bulk flow velocities, belt inclinations and bulk feeding from 2 conveyors into one chute are taken into account. Conventional chutes have parabolic belt impact walls. An improved version with divided impact walls is proposed that maintains a relatively high bulk velocity, reduces friction at chute walls and decreases wear and dirt build-up. Design of the improved chute is explained. It is built to adapt to existing structures without major modifications. The angle between 2 belt conveyors can be up to 90 degrees, the best bulk transfer is noted at conveyor angles below 60 degrees. Various graphs and schemes are provided. 6 refs.

Modeling and energy efficiency optimization of belt conveyors

International Nuclear Information System (INIS)

Zhang, Shirong; Xia, Xiaohua

2011-01-01

Highlights: → We take optimization approach to improve operation efficiency of belt conveyors. → An analytical energy model, originating from ISO 5048, is proposed. → Then an off-line and an on-line parameter estimation schemes are investigated. → In a case study, six optimization problems are formulated with solutions in simulation. - Abstract: The improvement of the energy efficiency of belt conveyor systems can be achieved at equipment and operation levels. Specifically, variable speed control, an equipment level intervention, is recommended to improve operation efficiency of belt conveyors. However, the current implementations mostly focus on lower level control loops without operational considerations at the system level. This paper intends to take a model based optimization approach to improve the efficiency of belt conveyors at the operational level. An analytical energy model, originating from ISO 5048, is firstly proposed, which lumps all the parameters into four coefficients. Subsequently, both an off-line and an on-line parameter estimation schemes are applied to identify the new energy model, respectively. Simulation results are presented for the estimates of the four coefficients. Finally, optimization is done to achieve the best operation efficiency of belt conveyors under various constraints. Six optimization problems of a typical belt conveyor system are formulated, respectively, with solutions in simulation for a case study.

Energy-saving belt conveyors installed in Polish collieries

Directory of Open Access Journals (Sweden)

Jerzy ANTONIAK

2010-01-01

Full Text Available An important problem of reducing energy consumption and dioxide emissions in the stage of construction and operation of mine belt conveyors is connected with their broad use in the industry. However, this notion is related to a reduction of electric energy consumption for conveyor drive and for production of conveyor components and assemblies (belts, rollers, load-bearing structure etc.. An essential role is played by an increased life of belt conveyors assemblies and components, principally belts. A reduced electric energy consumption results in a decreased CO2 emissions, e.g. hard coal – fired power station issues 0.28 kg CO2 per production of 1 kWh, in to answer production of 1 t steel accounts for 3.2 t CO2 emissions. The subject-matter presented in the paper concerning energy-saving in the horizontally and inclined mine belt conveyors installed in a Polish colliery – Anna, Jankowice and Marcel, has a big economic significance and it is important from the point of view of environmental protection.

Belt conveyor dynamics in transient operation for speed control

NARCIS (Netherlands)

He, D.; Pang, Y.; Lodewijks, G.

2016-01-01

Belt conveyors play an important role in continuous dry bulk material transport, especially at the mining industry. Speed control is expected to reduce the energy consumption of belt conveyors. Transient operation is the operation of increasing or decreasing conveyor speed for speed control.

Chaos on the conveyor belt.

Science.gov (United States)

Sándor, Bulcsú; Járai-Szabó, Ferenc; Tél, Tamás; Néda, Zoltán

2013-04-01

The dynamics of a spring-block train placed on a moving conveyor belt is investigated both by simple experiments and computer simulations. The first block is connected by a spring to an external static point and, due to the dragging effect of the belt, the blocks undergo complex stick-slip dynamics. A qualitative agreement with the experimental results can be achieved only by taking into account the spatial inhomogeneity of the friction force on the belt's surface, modeled as noise. As a function of the velocity of the conveyor belt and the noise strength, the system exhibits complex, self-organized critical, sometimes chaotic, dynamics and phase transition-like behavior. Noise-induced chaos and intermittency is also observed. Simulations suggest that the maximum complexity of the dynamical states is achieved for a relatively small number of blocks (around five).

Belt design central to conveyor performance

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-15

While a conveyor system comprises a complex range of components, it is the belt design which ultimately dictates its core performance and reliability. The complexity of modern systems can be seen by the recent contract awarded to ThyssenKrupp Foerdertechnik (TKF) to supply systems for a new steel plant (including a coking plant and a power plant) to be built in Sepetiba Bay in Brazil. Phoenix has designed the Phoenotec system to protect steel cord conveyor belts. Fenner Dunlop has developed Fenaplast belting with nylon or polyester load-bearing warp and weft yarns for good impact resistance. 2 photos.

RATIONALE FOR CENTERING CAPACITY OF REDISIGNED BELT CONVEYOR DRUMS

Directory of Open Access Journals (Sweden)

V. V. Suglobov

2016-02-01

Full Text Available Purpose. In the study is necessary: 1 to justify aligning drums of a new design of belt conveyors; 2 to develop a method for calculating and determining the rational design parameters of drums depending on the technical parameters of the conveyor belt (the length of the conveyor, belt width, the performance of the conveyor, the diameter of the drive and tension drums, etc.; 3 to carry out pilot studies of efficiency conveyor belt in a production environment in order to determine the magnitude of dynamic loads and a comparative evaluation of the effectiveness of the centering ability of conventional and new designs of drums. Methodology. To substantiate the effectiveness of the centering ability of the drums of a new design by the authors developed a mathematical model of interaction of the tape with the drum. Mathematical simulation of tape reels with new design comes to drawing up a differential equation of the belt based on the dynamic component and restoring force. This model allowed us to estimate the movement of the tape in the transverse direction based on the calculated additional dynamic loads and forces on the investigated centering a conveyor belt with given specifications. For the first time the technique of calculating and determining the rational parameters of the drums, which allows determining the design parameters of the centering portions, depending on the mechanical properties and geometric parameters of the tape. Findings. With the help of mathematical modeling the scientifically substantiated effect of centering the ability of the new design of the drum, which ensures stable tape running along the longitudinal axis of the conveyor. The authors made the following conclusions: 1 the mathematical model of interaction with the new belt design of the drum, which allowed to describe the belt in the transverse direction in view of additional dynamic loads and renewable power was developed; 2 the method of calculation and

Selection of Belt Conveyors Drive Units Number by Technical –Economical Analysis

OpenAIRE

Despodov, Zoran; Mijalkovski, Stojance; Adjiski, Vancho; Panov, Zoran

2014-01-01

In this paper is presented a methodology for selection of belt conveyor drive units number by technical - economical analysis of their parameters. Belt Conveyors with follow drive arrangement will be considered: one, two, three and four drive units. In the technical - economical analysis are including: Tension forces, Power of belt conveyor, Costs for belt, Costs for power and reducers, Total cost for belt conveyor system.

Energy saving for belt conveyors by speed control

NARCIS (Netherlands)

He, D.

2017-01-01

Belt conveyors are widely used in bulk solids handling and conveying systems. Considering the extensive use of belt conveyors, their operations involve a large amount of energy. Taking the relevant economic and social challenges into account, there is a strong demand for lowering the energy

Synaptic ribbon. Conveyor belt or safety belt?

Science.gov (United States)

Parsons, T D; Sterling, P

2003-02-06

The synaptic ribbon in neurons that release transmitter via graded potentials has been considered as a conveyor belt that actively moves vesicles toward their release sites. But evidence has accumulated to the contrary, and it now seems plausible that the ribbon serves instead as a safety belt to tether vesicles stably in mutual contact and thus facilitate multivesicular release by compound exocytosis.

A Parametric Energy Model for Energy Management of Long Belt Conveyors

Directory of Open Access Journals (Sweden)

Tebello Mathaba

2015-12-01

Full Text Available As electricity prices continue to rise, the increasing need for energy management requires better understanding of models for energy-consuming applications, such as conveyor belts. Conveyor belts are used in a wide range of industries, including power generation, mining and mineral processing. Conveyor technological advances are leading to increasingly long conveyor belts being commissioned. Thus, the energy consumption of each individual belt conveyor unit is becoming increasingly significant. This paper proposes a generic energy model for belt conveyors with long troughed belts. The model has a two-parameter power equation, and it uses a partial differential equation to capture the variable amount of material mass per unit length throughout the belt length. Verification results show that the power consumption calculations of the newly proposed simpler model are consistent with those of a known non-linear model with an error of less than 4%. The online parameter identification set-up of the model is proposed. Simulations indicate that the parameters can be identified successfully from data with up to 15% measurement noise. Results show that the proposed model gives better predictions of the power consumed and material delivered by a long conveyor belt than the steady-state models in the current literature.

Conveyor belt weigher using a nuclear technique

International Nuclear Information System (INIS)

Magal, B.S.

1976-01-01

Principles of operation of different types of continuous conveyor belt weighing machines developed for use in factories for bulk weighing of material on conveyor belts without interupting the material flow, are briefly mentioned. The design of nuclear weighing scale making use of the radiation absorption property of the material used is described in detail. The radiation source, choice of the source, detector and geometry of such a weighing scale are discussed. The nucleonic belt weigher is compared with the gravimetric belt weigher system. The advantages of the nuclear system are pointed out. The assembly drawing of the electronics, calibration procedure and performance evaluation are given. (A.K.)

Optimal control of operation efficiency of belt conveyor systems

International Nuclear Information System (INIS)

Zhang, Shirong; Xia, Xiaohua

2010-01-01

The improvement of the energy efficiency of belt conveyor systems can be achieved at equipment or operation levels. Switching control and variable speed control are proposed in literature to improve energy efficiency of belt conveyors. The current implementations mostly focus on lower level control loops or an individual belt conveyor without operational considerations at the system level. In this paper, an optimal switching control and a variable speed drive (VSD) based optimal control are proposed to improve the energy efficiency of belt conveyor systems at the operational level, where time-of-use (TOU) tariff, ramp rate of belt speed and other system constraints are considered. A coal conveying system in a coal-fired power plant is taken as a case study, where great saving of energy cost is achieved by the two optimal control strategies. Moreover, considerable energy saving resulting from VSD based optimal control is also proved by the case study.

Optimal control of operation efficiency of belt conveyor systems

Energy Technology Data Exchange (ETDEWEB)

Zhang, Shirong [Department of Automation, Wuhan University, Wuhan 430072 (China); Xia, Xiaohua [Department of Electrical, Electronic and Computer Engineering, University of Pretoria, Pretoria 0002 (South Africa)

2010-06-15

The improvement of the energy efficiency of belt conveyor systems can be achieved at equipment or operation levels. Switching control and variable speed control are proposed in literature to improve energy efficiency of belt conveyors. The current implementations mostly focus on lower level control loops or an individual belt conveyor without operational considerations at the system level. In this paper, an optimal switching control and a variable speed drive (VSD) based optimal control are proposed to improve the energy efficiency of belt conveyor systems at the operational level, where time-of-use (TOU) tariff, ramp rate of belt speed and other system constraints are considered. A coal conveying system in a coal-fired power plant is taken as a case study, where great saving of energy cost is achieved by the two optimal control strategies. Moreover, considerable energy saving resulting from VSD based optimal control is also proved by the case study. (author)

30 CFR 14.22 - Test for flame resistance of conveyor belts.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Test for flame resistance of conveyor belts. 14..., EVALUATION, AND APPROVAL OF MINING PRODUCTS REQUIREMENTS FOR THE APPROVAL OF FLAME-RESISTANT CONVEYOR BELTS Technical Requirements § 14.22 Test for flame resistance of conveyor belts. (a) Test procedures. The test...

Belt Conveyor Dynamic Characteristics and Influential Factors

OpenAIRE

Li, Junxia; Pang, Xiaoxu

2018-01-01

This paper uses the Kelvin-Voigt viscoelastic model to establish the continuous dynamic equations for tail hammer tension belt conveyors. The viscoelastic continuity equations are solved using the generalized coordinate method. We analyze various factors influencing longitudinal vibration of the belt conveyor by simulation and propose a control strategy to limit the vibration. The proposed approach and control strategy were verified by several experimental researches and cases. The proposed a...

Method of monitoring, inspecting or testing conveyor belts

International Nuclear Information System (INIS)

Van der Walt, A.J.

1985-01-01

An invention is discussed which provides a method, installation and kit for monitoring, inspecting or testing a conveyor belt. Provision is made to transmit penetrating rays such as X-rays through a moving conveyor belt, forming a visible moving image from rays transmitted through the belt, and visually inspecting such moving image, after recording it if desired, to ascertain the condition of the interior of the belt. Typically an X-ray tube head is used to transmit the rays through the belt to a fluorescent screen which forms the image. The moving image can be recorded by means of a video camera

Second longest conveyor belt in UK installed and fully operational

Energy Technology Data Exchange (ETDEWEB)

1981-07-01

A conveyor belt (which after the completion of the Selby complex will be the second longest conveyor belt in the UK) has been installed at the Prince Charles Drift Mine, Prince of Wales Colliery, United Kingdom. The 1706 m conveyor is the sole underground-to-surface conveyor at the Drift Mine, and is powered by a single 2240 kW, 3000 hp drive unit.

Design of belt conveyors in bulk terminal applications. Part II

Energy Technology Data Exchange (ETDEWEB)

Goodwin, P J; Ramos, C M

1986-04-01

The main design parameters used for belt conveyors in harbour applications are discussed. Conveyor belting including the carcass, belt cover, belt tension and speed, and safety factors, idlers, conveyor pulleys, motors, fluid couplings and drive arrangements are considered. Technical factors are briefly outlined for the designer to consider to achieve minimum acceptable component service life. A method is discussed to reduce coal degradation investigated using a test chute designed for the purpose of minimizing sized coal degradation at transfer points in the refurbishing of the Durban Coal Terminal. 24 references.

New Quality Standards of Testing Idlers for Highly Effective Belt Conveyors

Science.gov (United States)

Król, Robert; Gladysiewicz, Lech; Kaszuba, Damian; Kisielewski, Waldemar

2017-12-01

The paper presents result of research and analyses carried out into the belt conveyors idlers’ rotational resistance which is one of the key factor indicating the quality of idlers. Moreover, idlers’ rotational resistance is important factor in total resistance to motion of belt conveyor. The evaluation of the technical condition of belt conveyor idlers is carried out in accordance with actual national and international standards which determine the methodology of measurements and acceptable values of measured idlers’ parameters. Requirements defined by the standards, which determine the suitability of idlers to a specific application, despite the development of knowledge on idlers and quality of presently manufactured idlers maintain the same level of parameters values over long periods of time. Nowadays the need to implement new, efficient and economically justified solution for belt conveyor transportation systems characterized by long routes and energy-efficiency is often discussed as one of goals in belt conveyors’ future. One of the basic conditions for achieving this goal is to use only carefully selected idlers with low rotational resistance under the full range of operational loads and high durability. Due to this it is necessary to develop new guidelines for evaluation of the technical condition of belt conveyor idlers in accordance with actual standards and perfecting of existing and development of new methods of idlers testing. The changes in particular should concern updating of values of parameters used for evaluation of the technical condition of belt conveyor idlers in relation to belt conveyors’ operational challenges and growing demands in terms of belt conveyors’ energy efficiency.

Study on Fuzzy Comprehensive Evaluation Model for the Safety of Mine Belt Conveyor

Directory of Open Access Journals (Sweden)

Gong Xiaoyan

2017-01-01

Full Text Available To improve the situation of the frequent failures of mine belt conveyor during operation, a model was used to evaluate the safety of mine belt conveyor. Based on the foundation of collecting and analyzing a large quantity of fault information of belt conveyor in the nationwide coal mine, the fault tree model of belt conveyor has been built, then the safety evaluation index system was established by analyzing and removing some secondary indicators. Furthermore, the weighted value of safety evaluation indexs was determined by analytic hierarchy process(AHP, and the single factor fuzzy evaluation matrix was constructed by experts grading method. Additionally, the model was applied in evaluating the security of belt conveyor in Nanliang coal mine. The results shows the security level is recognized to the “general”, which means that this model can be adopted widely in evaluating the safety of mine belt conveyor.

A minimalistic and optimized conveyor belt for neutral atoms.

Science.gov (United States)

Roy, Ritayan; Condylis, Paul C; Prakash, Vindhiya; Sahagun, Daniel; Hessmo, Björn

2017-10-20

Here we report of a design and the performance of an optimized micro-fabricated conveyor belt for precise and adiabatic transportation of cold atoms. A theoretical model is presented to determine optimal currents in conductors used for the transportation. We experimentally demonstrate a fast adiabatic transportation of Rubidium ( 87 Rb) cold atoms with minimal loss and heating with as few as three conveyor belt conductors. This novel design of a multilayered conveyor belt structure is fabricated in aluminium nitride (AlN) because of its outstanding thermal and electrical properties. This demonstration would pave a way for a compact and portable quantum device required for quantum information processing and sensors, where precise positioning of cold atoms is desirable.

Belt conveyor apparatus

Science.gov (United States)

Oakley, David J.; Bogart, Rex L.

1987-01-01

A belt conveyor apparatus according to this invention defines a conveyance path including a first pulley and at least a second pulley. An endless belt member is adapted for continuous travel about the pulleys and comprises a lower portion which engages the pulleys and an integral upper portion adapted to receive objects therein at a first location on said conveyance path and transport the objects to a second location for discharge. The upper belt portion includes an opposed pair of longitudinally disposed crest-like members, biased towards each other in a substantially abutting relationship. The crest-like members define therebetween a continuous, normally biased closed, channel along the upper belt portion. Means are disposed at the first and second locations and operatively associated with the belt member for urging the normally biased together crest-like members apart in order to provide access to the continuous channel whereby objects can be received into, or discharged from the channel. Motors are in communication with the conveyance path for effecting the travel of the endless belt member about the conveyance path. The conveyance path can be configured to include travel through two or more elevations and one or more directional changes in order to convey objects above, below and/or around existing structures.

Review of Dynamic Modeling and Simulation of Large Scale Belt Conveyor System

Science.gov (United States)

He, Qing; Li, Hong

Belt conveyor is one of the most important devices to transport bulk-solid material for long distance. Dynamic analysis is the key to decide whether the design is rational in technique, safe and reliable in running, feasible in economy. It is very important to study dynamic properties, improve efficiency and productivity, guarantee conveyor safe, reliable and stable running. The dynamic researches and applications of large scale belt conveyor are discussed. The main research topics, the state-of-the-art of dynamic researches on belt conveyor are analyzed. The main future works focus on dynamic analysis, modeling and simulation of main components and whole system, nonlinear modeling, simulation and vibration analysis of large scale conveyor system.

AUTOMATION OF CONVEYOR BELT TRANSPORT

Directory of Open Access Journals (Sweden)

Nenad Marinović

1990-12-01

Full Text Available Belt conveyor transport, although one of the most economical mining transport system, introduce many problems to mantain the continuity of the operation. Every stop causes economical loses. Optimal operation require correct tension of the belt, correct belt position and velocity and faultless rolls, which are together input conditions for automation. Detection and position selection of the faults are essential for safety to eliminate fire hazard and for efficient maintenance. Detection and location of idler roll faults are still open problem and up to now not solved successfully (the paper is published in Croatian.

Study on the application of permanent magnet synchronous motors in underground belt conveyors

Science.gov (United States)

Ma, S. H.

2017-12-01

This paper analyzes and compares the advantages and disadvantages of several kinds of drive devices of belt conveyors from the angle of energy saving, and summarizes the application advantages and using problems of permanent magnet motor variable frequency drive system in belt conveyors. An example is given to demonstrate the energy saving effect of this system compared with other driving methods. This paper points out the application prospect of permanent magnet motor variable frequency drive system on belt conveyors and other large mining machines in coal mine. This paper is aimed to provide the design direction for the designer and the choice basis for the user on belt conveyor.

A multi points ultrasonic detection method for material flow of belt conveyor

Science.gov (United States)

Zhang, Li; He, Rongjun

2018-03-01

For big detection error of single point ultrasonic ranging technology used in material flow detection of belt conveyor when coal distributes unevenly or is large, a material flow detection method of belt conveyor is designed based on multi points ultrasonic counter ranging technology. The method can calculate approximate sectional area of material by locating multi points on surfaces of material and belt, in order to get material flow according to running speed of belt conveyor. The test results show that the method has smaller detection error than single point ultrasonic ranging technology under the condition of big coal with uneven distribution.

Realization methodology for optimal design of steel structures conveyors with hanging belt

Directory of Open Access Journals (Sweden)

Boslovyak P.V.

2016-03-01

Full Text Available Presents the results of optimum design of metal structures of the fixed conveyor with hanging belt. The analysis results optimum design of steel structures of stationary conveyor with hanging belt.

COMPREHENSIVE CHECK MEASUREMENT OF KEY PARAMETERS ON MODEL BELT CONVEYOR

Directory of Open Access Journals (Sweden)

Vlastimil MONI

2013-07-01

Full Text Available Complex measurements of characteristic parameters realised on a long distance model belt conveyor are described. The main objective was to complete and combine the regular measurements of electric power on drives of belt conveyors operated in Czech opencast mines with measurements of other physical quantities and to gain by this way an image of their mutual relations and relations of quantities derived from them. The paper includes a short description and results of the measurements on an experimental model conveyor with a closed material transport way.

DEVELOPMENT OF THE TEST METHODS OF THE CONVEYOR BELTS USED IN ENVIRONMENTS ENDANGERED BY EXPLOSION HAZARDS

Directory of Open Access Journals (Sweden)

Florin Adrian PĂUN

2012-05-01

Full Text Available Conveyor belts are used for a long period of time in the industry branches where potentially explosive atmospheres could occur. Dangerous phenomena which can be in direct connection with the use of conveyor belts are the ones regarding: - sparks influence over the coating layer and/or resistance internal structure of the stopped conveyor belt; - propagation of a flame along the length of a conveyor belt that was exposed to a energy source relative high like a fire or due to blockage of a conveyor belt as a result of the driving mechanism still operating, that generate a local heating of the conveyor belt in contact with the driving drum, rollers or any other heating source generated by friction. Determining the safety parameters characteristic of the conveyor belts by employing test methods allows assessment of the safety level as well as certification of their explosion protection quality when used in environments with explosion danger.

Determination of relative immobile and sliding areas between carrying and tractive belts in using of belt conveyor intermediate drives

OpenAIRE

Goncharov K.A.

2015-01-01

Method of determination of relative immobile and sliding areas between carrying and tractive belts in places of mount-ing of belt conveyor intermediate drives made in the form of tractive contours is proposed. The example shows potential of this method in multidrive belt conveyor design process.

Determination of relative immobile and sliding areas between carrying and tractive belts in using of belt conveyor intermediate drives

Directory of Open Access Journals (Sweden)

Goncharov K.A.

2015-12-01

Full Text Available Method of determination of relative immobile and sliding areas between carrying and tractive belts in places of mount-ing of belt conveyor intermediate drives made in the form of tractive contours is proposed. The example shows potential of this method in multidrive belt conveyor design process.

Mesin Pemindah Bahan : Studi Prestasi Belt Conveyor Hubungannya Dengan Ukuran Butiran Dan Tingkat Kelembaban Bahan Curah ( Batubara ), Panjang Belt 7,6 Meter ; Lebar 32 Centimeter

OpenAIRE

Nugroho, Rio

2011-01-01

Banyak industri yang menggunakan belt conveyor sebagai alat transportasi material, sebab punya banyak keuntungan. Sehingga, untuk meningkatkan performansi belt conveyor tersebut perlu dilakukan pengidentifikasian prestasi belt conveyor. Identifikasi dilakukan dengan material transfer batubara. Yang akan diamati adalah pengaruh ukuran butiran material dan tingkat kelembaban terhadap kapasitas transfer belt conveyor. Dari pengujian didapatkan kapasitas transfer terbesar adalah material batubar...

Numerical modeling of water spray suppression of conveyor belt fires in a large-scale tunnel.

Science.gov (United States)

Yuan, Liming; Smith, Alex C

2015-05-01

Conveyor belt fires in an underground mine pose a serious life threat to miners. Water sprinkler systems are usually used to extinguish underground conveyor belt fires, but because of the complex interaction between conveyor belt fires and mine ventilation airflow, more effective engineering designs are needed for the installation of water sprinkler systems. A computational fluid dynamics (CFD) model was developed to simulate the interaction between the ventilation airflow, the belt flame spread, and the water spray system in a mine entry. The CFD model was calibrated using test results from a large-scale conveyor belt fire suppression experiment. Simulations were conducted using the calibrated CFD model to investigate the effects of sprinkler location, water flow rate, and sprinkler activation temperature on the suppression of conveyor belt fires. The sprinkler location and the activation temperature were found to have a major effect on the suppression of the belt fire, while the water flow rate had a minor effect.

Numerical modeling of water spray suppression of conveyor belt fires in a large-scale tunnel

Science.gov (United States)

Yuan, Liming; Smith, Alex C.

2015-01-01

Conveyor belt fires in an underground mine pose a serious life threat to miners. Water sprinkler systems are usually used to extinguish underground conveyor belt fires, but because of the complex interaction between conveyor belt fires and mine ventilation airflow, more effective engineering designs are needed for the installation of water sprinkler systems. A computational fluid dynamics (CFD) model was developed to simulate the interaction between the ventilation airflow, the belt flame spread, and the water spray system in a mine entry. The CFD model was calibrated using test results from a large-scale conveyor belt fire suppression experiment. Simulations were conducted using the calibrated CFD model to investigate the effects of sprinkler location, water flow rate, and sprinkler activation temperature on the suppression of conveyor belt fires. The sprinkler location and the activation temperature were found to have a major effect on the suppression of the belt fire, while the water flow rate had a minor effect. PMID:26190905

30 CFR 75.1101 - Deluge-type water sprays, foam generators; main and secondary belt-conveyor drives.

Science.gov (United States)

2010-07-01

... and secondary belt-conveyor drives. 75.1101 Section 75.1101 Mineral Resources MINE SAFETY AND HEALTH... Fire Protection § 75.1101 Deluge-type water sprays, foam generators; main and secondary belt-conveyor... be installed at main and secondary belt-conveyor drives. ...

An electromyographic and kinematic comparison between an extendable conveyor system and an articulating belt conveyor used for truck loading and unloading tasks.

Science.gov (United States)

Lavender, Steven A; Nagavarapu, Shasank; Allread, W Gary

2017-01-01

Many retail distribution centers (DCs) manually load and unload boxes into or out of trailers and shipping containers. This study investigated whether an articulating belt conveyor with a height adjustable platform, positioned at the end of an extendable conveyor, significantly reduces shoulder and back muscle loading and the spine kinematics associated with these tasks. Electromyographic and kinematic data were collected from eight volunteer employees as trailers at a shoe DC were unloaded and from nine volunteer employees as trailers at an apparel DC were loaded. Participants in this repeated measures study handled boxes with a conventional powered extendable conveyor system and with the articulating belt conveyor positioned at the end of the extendable conveyor. Bilaterally the normalized activation levels of the erector spinae and anterior deltoid muscles were reduced when loading and unloading boxes with the articulating belt conveyor. Spine movement speeds were also reduced with the articulating conveyor. Copyright © 2016 Elsevier Ltd. All rights reserved.

On-conveyor belt determination of ash in coal

International Nuclear Information System (INIS)

Sowerby, B.; Lim, C.S.; Abernethy, D.A.; Liu, Y.; Maguire, P.A.

1997-01-01

A laboratory feasibility study has been carried out on new and advanced neutron and gamma-ray analysis systems for the direct on-conveyor belt analysis of ash in coal without the need for sample by-lines. Such an analysis system could deliver the combined advantages of a direct on-conveyor configuration with new and accurate analysis techniques. An industry survey of 18 coal companies carried out in early 1996 indicated that accurate on-belt ash analysis is of the highest priority. Subsequent laboratory work has focussed on the investigation of methods with the potential for improving the accuracy of ash content measurement relative to existing on-belt ash analysers, the most widely-used of which are based on dual energy gamma-ray transmission (DUET), which is sensitive to variations in ash composition. The current work indicates that on-belt neutron/gamma-ray techniques combined with advanced spectral analysis techniques show promise for development into an on-belt ash analysis system which is significantly less sensitive to composition changes than DUET and which analyses a much larger proportion of coal on the belt, thus eliminating some key sources of analysis error

Application of the method finite elements by numerical modeling stress-strain state in conveyor belts

Directory of Open Access Journals (Sweden)

Maras Michal

1997-06-01

Full Text Available Solving problems connected with damaging a conveyor belt at the transfer points is conditioned by knowing laws of this phenomenon. Acquiring the knowledge on this phenomen is possible to be gained either by experimental research or by the numerical model GEM 22, which enables to determine the distribution of stresses and strains in a suitably selected cross-section of a conveyor belt. The paper begins by defining the problem, determining the boundary model conditions and continues by modelling the dynamic force acting on the conveyor belt. In the conclusions of the paper there are given table and graphical results of the numerical modelling aimed at solving the problems connected with the damaging of a conveyor belt. By numerical modelling, in this case the finite element method, in the given way can be realized the parametric studies with changing values of input parameters, especially: - stretching force, - thickness of cover layers of the conveyor belt and strain properties of the rubber, - parameters of the steel cord of the conveyor belt.

Design of belt conveyors in bulk terminal applications. Part 1

Energy Technology Data Exchange (ETDEWEB)

Goodwin, P J; Ramos, C M

1985-10-01

This paper discusses belt conveyors and their development in bulk terminal applications in South Africa. Single- and multi-product terminal philosophy is discussed, including methods of handling different products over the same system and limiting the effects of degradation at transfer points. In Part II, some aspects of belt conveyor design, as well as the results of tests on a chute designed to handle a range of products, will be covered. 23 references.

Model predictive control based on reduced order models applied to belt conveyor system.

Science.gov (United States)

Chen, Wei; Li, Xin

2016-11-01

In the paper, a model predictive controller based on reduced order model is proposed to control belt conveyor system, which is an electro-mechanics complex system with long visco-elastic body. Firstly, in order to design low-degree controller, the balanced truncation method is used for belt conveyor model reduction. Secondly, MPC algorithm based on reduced order model for belt conveyor system is presented. Because of the error bound between the full-order model and reduced order model, two Kalman state estimators are applied in the control scheme to achieve better system performance. Finally, the simulation experiments are shown that balanced truncation method can significantly reduce the model order with high-accuracy and model predictive control based on reduced-model performs well in controlling the belt conveyor system. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

A new press line concept for conveyor belts; Neues Pressenkonzept fuer Foerdergurte

Energy Technology Data Exchange (ETDEWEB)

Aumueller, Steffen [Siempelkamp Maschinen- und Anlagenbau GmbH und Co. KG, Krefeld (Germany)

2010-06-15

Pressure and temperature are the relevant process parameters for the vulcanisation of rubber products. Particularly, the vulcanisation of large-surface rubber products such as belt conveyors sets large requirements on the mechanical characteristics of the press lines. Siempelkamp Maschinen- und Anlagenbau GmbH and Co. KG (Krefeld, Federal Republic of Germany) is specialized on these requirements. For over 100 years, this company constructs vulcanisation presses for the belt conveyor industry. In the first ten decades, the layout of the press lines according to stiffness and transmission of large forces were in the focus. Till to the late 1980ies, these press lines represented the standard of the belt conveyor industry.

The Stability of the Conveyor Belt Pontoon

Directory of Open Access Journals (Sweden)

Jiří PODEŠVA

2011-06-01

Full Text Available To lead the conveyor belt transport cross water area the pontoon are used to support the carrying structure of the belts. The accident can happen when the pontoon turnover. For this reason the pontoon stability is investigated. The stability is described by the Reed’s diagram. This can be constructed analytically or via numerical modeling. Both methods are described in the paper.

Studi Pengaruh Ukuran Butir Dan Tingkat Kelembaban Pasir Terhadap Performansi Belt Conveyor Pada Pabrik Pembuatan Tiang Beton

OpenAIRE

Depari, Prianto

2010-01-01

Pabrik pembuatan tiang beton yang menggunakan belt conveyor sebagai alat transportasi material yang berbentuk bulk. Material pasir adalah salah satu contoh material bulk, yang diangkut dengan belt conveyor untuk proses mix bahan baku dari beton seperti kerikil, semen, agregat dan lain-lain. Penggunaan belt conveyor ini akan meningkatkan efisiensi kerja dari pabrik pembuatan beton. Performansi belt conveyor tersebut perlu diidentifikasian secara baik dan benar. Identifikasi dilakukan dengan be...

Vibration analysis on automatic take-up device of belt conveyor

Science.gov (United States)

Qin, Tailong; Wei, Jin

2008-10-01

Through introducing application condition of belt conveyor in the modern mining industry, the paper proposed, in the dynamic course of its starting, braking or loading, it would produce moving tension and elastic wave. And analyzed the factors cause the automatic take-up device of belt conveyor vibrating: the take-up device's structure and the elastic wave. Finally the paper proposed the measure to reduce vibration and carried on the modeling and simulation on the tension buffer device.

Energy optimization of conveyor belts at RWE Power AG; Energetische Optimierung von Foerdergurten bei der RWE Power AG

Energy Technology Data Exchange (ETDEWEB)

Ziegler, Manfred [RWE Power International RE GmbH, Koeln (Germany). Gewinnungs- und Foerdertechnik

2009-11-15

Influencing horizontal resistance to motion has the greatest leverage effect in terms of reducing the power requirements of belt conveyors. The selection of a suitable conveyor belt with optimized running resistance enables substantial cost savings, both with regard to current energy consumption and with regard to the drive power to be installed. Measurements carried out on standard conveyor belts used by RWE Power show differences of up to 30 % in the principal resistance. A method to reliably predict the energy properties of a conveyor belt by means of small specimens was developed. In addition, the requirements to be met in terms of mechanical endurance of a belt depending on conveyor configuration, which set limits to the development of energy-saving belts suitable for operation, will be outlined. To resolve this conflict of aims, conveyor engineers are given concrete tips on the design of belt conveyor systems. (orig.)

Design of dual energy x-ray detector for conveyor belt with steel wire ropes

Science.gov (United States)

Dai, Yue; Miao, Changyun; Rong, Feng

2009-07-01

A dual energy X-ray detector for conveyor belt with steel wire ropes is researched in the paper. Conveyor belt with steel wire ropes is one of primary transfer equipments in modern production. The traditional test methods like electromagnetic induction principle could not display inner image of steel wire ropes directly. So X-ray detection technology has used to detect the conveyor belt. However the image was not so clear by the interference of the rubber belt. Therefore, the dualenergy X-ray detection technology with subtraction method is developed to numerically remove the rubber belt from radiograph, thus improving the definition of the ropes image. The purpose of this research is to design a dual energy Xray detector that could make the operator easier to found the faulty of the belt. This detection system is composed of Xray source, detector controlled by FPGA chip, PC for running image processing system and so on. With the result of the simulating, this design really improved the capability of the staff to test the conveyor belt.

Design of belt conveyor electric control device based on CC-link bus

Science.gov (United States)

Chen, Goufen; Zhan, Minhua; Li, Jiehua

2016-01-01

In view of problem of the existing coal mine belt conveyor is no field bus communication function, two levels belt conveyor electric control system design is proposed based on field bus. Two-stage belt conveyor electric control system consists of operation platform, PLC control unit, various sensors, alarm device and the water spraying device. The error protection is realized by PLC programming, made use of CC-Link bus technology, the data share and the cooperative control came true between host station and slave station. The real-time monitor was achieved by the touch screen program. Practical application shows that the system can ensure the coalmine production, and improve the automatic level of the coalmine transport equipment.

PROPOSALS ON IMPROVING THE EXCAVATION, TRANSPORT AND COAL DEPOSIT, USING THE RUBBER CONVEYOR BELT

Directory of Open Access Journals (Sweden)

Nicoleta-Maria MIHUT

2016-05-01

Full Text Available In this work we make a study of the improvement methods of quantity of material transported by conveyor belt. Determination of discharge of solids entail establish of the parameters of the conveyor belt. As a result, we determine the belt speed who provide maximum discharge of solids materials.

Investigation into the effect of common factors on rolling resistance of belt conveyor

Directory of Open Access Journals (Sweden)

Lu Yan

2015-08-01

Full Text Available Since indentation rolling resistance accounts for the major part of total resistance of belt conveyor, it is important to compute it using a proper method during the design and application study of the belt conveyor. First, an approximate formula for computing the indentation rolling resistance is offered. In this formula, a one-dimensional Winkler foundation and a three-parameter viscoelastic Maxwell solid model of the belt backing material are used to determine the resistance to motion of a conveyor belt over idlers. With the help of this formula, the authors analyze the effect of common factors on the rolling resistance. Finally, experiments are carried out under certain condition compared with theoretical analysis. A reasonable correlation exists between the experimental results and the theoretical formulae.

Non-linear belt transient analysis. A hybrid model for numerical belt conveyor simulation

Energy Technology Data Exchange (ETDEWEB)

Harrison, A. [Scientific Solutions, Inc., Aurora, CO (United States)

2008-07-01

Frictional and rolling losses along a running conveyor are discussed due to their important influence on wave propagation during starting and stopping. Hybrid friction models allow belt rubber losses and material flexing to be included in the initial tension calculations prior to any dynamic analysis. Once running tensions are defined, a numerical integration method using non-linear stiffness gradients is used to generate transient forces during starting and stopping. A modified Euler integration technique is used to simulate the entire starting and stopping cycle in less than 0.1 seconds. The procedure enables a faster scrutiny of unforeseen conveyor design issues such as low belt tension zones and high forces at drives. (orig.)

Conveyor belt nuclear weighing machine

International Nuclear Information System (INIS)

Anon.

1977-01-01

In many industries the flow of materials on conveyor belts must be measured and controlled. Electromechanical weighing devices have high accuracy but are complicated and expensive to install and maintain. For many applications the nuclear weighing machine has sufficient accuracy but is considerably simpler, cheaper and more robust and is easier to maintain. The rating and performance of a gamma ray balance on the mar ket are detailed. (P.G.R.)

30 CFR 57.4263 - Underground belt conveyors.

Science.gov (United States)

2010-07-01

....4263 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Fire Prevention and Control Firefighting Equipment § 57.4263 Underground belt conveyors. Fire protection shall be...

Angle stations in or for endless conveyor belts

Science.gov (United States)

Steel, Alan

1987-04-07

In an angle station for an endless conveyor belt, there are presented to each incoming run of the belt stationary curved guide members (18, 19) of the shape of a major segment of a right-circular cylinder and having in the part-cylindrical portion (16 or 17) thereof rectangular openings (15) arranged in parallel and helical paths and through which project small freely-rotatable rollers (14), the continuously-changing segments of the curved surfaces of which projecting through said openings (15) are in attitude to change the direction of travel of the belt (13) through 90.degree. during passage of the belt about the part-cylindrical portion (16 or 17) of the guide member (18 or 19). The rectangular openings (15) are arranged with their longer edges lengthwise of the diagonals representing the mean of the helix but with those of a plurality of the rows nearest to each end of the part-cylindrical portion (16 or 17) slightly out of axial symmetry with said diagonals, being slightly inclined in a direction about the intersections (40) of the diagonals of the main portion of the openings, to provide a "toe-in" attitude in relation to the line of run of the endless conveyor belt.

Design aspects of multiple driven belt conveyors

NARCIS (Netherlands)

Nuttall, A.J.G.

2007-01-01

Worldwide belt conveyors are used to transport a great variety of bulk solid materials. The desire to carry higher tonnages over longer distances and more diverse routes, while keeping exploitation costs as low as possible, has fuelled many technological advances. An interesting development in the

Profit from plant experience in specifying coal conveyors

Energy Technology Data Exchange (ETDEWEB)

Rajter, L C

1985-09-01

Most coal conveyors in operation today were designed to handle raw unwashed coal and are experiencing difficulties when dealing with fine, wet coal which has been cleaned. Conveyor designers should base their designs for new systems on the worst possible materials. Design criteria are discussed in detail and recommendations made for chute liners and radii, skirt system, belt speed, transfer points, belt wipers, weather protection and access. 3 references.

RESEARCH ON THE HOMOGENEITY OF TEMPERATURES IN JOINT'S AREA BY VULCANIZING THE CONVEYOR BELTS

Directory of Open Access Journals (Sweden)

Dan DOBROTA

2016-05-01

Full Text Available The researches presented in this paper have followed the analysis of the heat transfer mode during joining through vulcanization of the conveyor belts and also the homogeneity of the temperatures in the joint area. The researches were made under laboratory conditions taking into account the process of joining of two conveyor belts of the type ST 2000 with an installation of the type DSLQ. Temperature measurement was conducted using an EX42570 pyrometer in four distinct points corresponding to each end of the two conveyor belts on the both sides of the band, namely the active and inactive side.

Overland conveyors. Cable or trough belt for 100 km transport haulage

Energy Technology Data Exchange (ETDEWEB)

Maton, A.E. [Maton Engineering Pty. Ltd., Orange Grove, WA (Australia)

2009-07-01

With the advances in belt conveyor technology today systems of 100 kilometres length are increasingly being considered. This article provides a comparison of two concepts for a 100 kilometre system of five 20 kilometre flights based on trough belt and cable belt technology. (orig.)

Type QH-200 conveyor-belt nuclear scale

International Nuclear Information System (INIS)

Li Shuming; Dong Shiyuan; Li Furong; Wan Zemin

1991-01-01

Type QH-200 conveyor-belt nuclear scale is a reliable and on-line device that weighs solids mass flow continuously by γ-ray absorption and scattering. The operation principle and measuring method are described. And some factors influencing the accuracy are discussed. The full scale total weight of type QH-200 nuclear scale is 10 6 t. The result of calibration in the industrial field shows that the accuracy of QH-200 is better than ±1.0% for typical belt loading

Critical phenomenon of granular flow on a conveyor belt.

Science.gov (United States)

De-Song, Bao; Xun-Sheng, Zhang; Guang-Lei, Xu; Zheng-Quan, Pan; Xiao-Wei, Tang; Kun-Quan, Lu

2003-06-01

The relationship between the granular wafer movement on a two-dimensional conveyor belt and the size of the exit together with the velocity of the conveyor belt has been studied in the experiment. The result shows that there is a critical speed v(c) for the granular flow when the exit width d is fixed (where d=R/D, D being the diameter of a granular wafers). When vv(c), the flow rate Q is described as Q=Crho(v)(beta)(d-k)(3/2). These are the effects of the interaction among the granular wafers and the change of the states of the granular flow due to the changing of the speed or the exit width d.

Plasmonic graded nano-disks as nano-optical conveyor belt.

Science.gov (United States)

Kang, Zhiwen; Lu, Haifei; Chen, Jiajie; Chen, Kun; Xu, Fang; Ho, Ho-Pui

2014-08-11

We propose a plasmonic system consisting of nano-disks (NDs) with graded diameters for the realization of nano-optical conveyor belt. The system contains a couple of NDs with individual elements coded with different resonant wavelengths. By sequentially switching the wavelength and polarization of the excitation source, optically trapped target nano-particle can be transferred from one ND to another. The feasibility of such function is verified based on the three-dimensional finite-difference time-domain technique and the Maxwell stress tensor method. Our design may provide an alternative way to construct nano-optical conveyor belt with which target molecules can be delivered between trapping sites, thus enabling many on-chip optofluidic applications.

Research on conditional characteristics vision real-time detection system for conveyor belt longitudinal tear

NARCIS (Netherlands)

Qiao, Tiezhu; Li, Xinyu; Pang, Y.; Lü, Yuxiang; Wang, Feng; Jin, Baoquan

2017-01-01

Conveyor belt longitudinal tear is one of the most serious problems in coal mining. Existing systems cannot realise lossless and real-time detection for longitudinal tear of conveyor belt. Currently, visual detecting systems are proposed by many researchers and are becoming the future trend. A

Evaluation of Criteria for the Detection of Fires in Underground Conveyor Belt Haulageways.

Science.gov (United States)

Litton, Charles D; Perera, Inoka Eranda

2012-07-01

Large-scale experiments were conducted in an above-ground gallery to simulate typical fires that develop along conveyor belt transport systems within underground coal mines. In the experiments, electrical strip heaters, imbedded ~5 cm below the top surface of a large mass of coal rubble, were used to ignite the coal, producing an open flame. The flaming coal mass subsequently ignited 1.83-meter-wide conveyor belts located approximately 0.30 m above the coal surface. Gas samples were drawn through an averaging probe located approximately 20 m downstream of the coal for continuous measurement of CO, CO 2 , and O 2 as the fire progressed through the stages of smoldering coal, flaming coal, and flaming conveyor belt. Also located approximately 20 m from the fire origin and approximately 0.5 m below the roof of the gallery were two commercially available smoke detectors, a light obscuration meter, and a sampling probe for measurement of total mass concentration of smoke particles. Located upstream of the fire origin and also along the wall of the gallery at approximately 14 m and 5 m upstream were two video cameras capable of both smoke and flame detection. During the experiments, alarm times of the smoke detectors and video cameras were measured while the smoke obscuration and total smoke mass were continually measured. Twelve large-scale experiments were conducted using three different types of fire-resistant conveyor belts and four air velocities for each belt. The air velocities spanned the range from 1.0 m/s to 6.9 m/s. The results of these experiments are compared to previous large-scale results obtained using a smaller fire gallery and much narrower (1.07-m) conveyor belts to determine if the fire detection criteria previously developed (1) remained valid for the wider conveyor belts. Although some differences between these and the previous experiments did occur, the results, in general, compare very favorably. Differences are duly noted and their impact on fire

Energy efficient idler for belt conveyor systems

Energy Technology Data Exchange (ETDEWEB)

Mukhopadhyay, A.K.; Chattopadhyay, A. [Indian School of Mines Univ., Dhanbad (India). Dept. of Mechanical Engineering and Mining; Soni, R.; Bhattnagar, M.

2009-07-01

In today's economic and legal environment, energy efficiency has become more important than ever. This paper proposes a new design of idler rollers for belt conveyors that could help to them even more efficient by reducing their energy consumption and also their CO{sub 2} footprint. (orig.)

Survival of Listeria monocytogenes on a conveyor belt material with or without antimicrobial additives.

Science.gov (United States)

Chaitiemwong, N; Hazeleger, W C; Beumer, R R

2010-08-15

Survival of Listeria monocytogenes on a conveyor belt material with or without antimicrobial additives, in the absence or presence of food debris from meat, fish and vegetables and at temperatures of 10, 25 and 37 degrees C was investigated. The pathogen survived best at 10 degrees C, and better at 25 degrees C than at 37 degrees C on both conveyor belt materials. The reduction in the numbers of the pathogen on belt material with antimicrobial additives in the first 6h at 10 degrees C was 0.6 log unit, which was significantly higher (Padditives. Reductions were significantly less (Pfood residue. At 37 degrees C and 20% relative humidity, large decreases in the numbers of the pathogen on both conveyor belt materials during the first 6h were observed. Under these conditions, there was no obvious effect of the antimicrobial substances. However, at 25 degrees C and 10 degrees C and high humidity (60-75% rh), a rapid decrease in bacterial numbers on the belt material with antimicrobial substances was observed. Apparently the reduction in numbers of L. monocytogenes on belt material with antimicrobial additives was greater than on belt material without additives only when the surfaces were wet. Moreover, the presence of food debris neutralized the effect of the antimicrobials. The results suggest that the antimicrobial additives in conveyor belt material could help to reduce numbers of microorganisms on belts at low temperatures when food residues are absent and belts are not rapidly dried. Copyright 2010 Elsevier B.V. All rights reserved.

Converter-controlled belt conveyor systems under the difficult conditions; Umrichtergesteuerte Bandanlagen unter schwierigen Bedingungen

Energy Technology Data Exchange (ETDEWEB)

Horz, Michael-Josef [RAG Deutsche Steinkohle, Herne (Germany). Abt. Elektrotechnik unter Tage; Mueller, Uwe [RAG Deutsche Steinkohle, Herne (Germany). Servicebereich Technik- und Logistikdienste

2010-05-15

Panel 572 is located at a depth of 1,200 m in the Girondelle seam at the West mine. The panel has a mean thickness of 2.5 m and is designed as a shearer loader face with a length of 460 m. Coal is conveyed to the shaft by six belts with a total length of about 6 km and a total lifting height of 396 m. The main conveyor belt 1 with an installed power of 3 MW links the panel to a bunker. Conveyor belts 2 to 4 each with 500 kW drive power have operated in a stable manner since the start of working of the panel. Due to in-seam drivage with a selective-cut machine of type AM 85 an area with a marked trough was produced in the coal conveyor road. This area is traversed by belt 5. The planning and control of the conveyor belt in this difficult geological environment impose high demands on drive and control technology. To ensure stable operation under different loads a raft of measures was resolved and implemented. The contribution examines the problem and describes the implemented measures in detail. (orig.)

Riding the belt

Energy Technology Data Exchange (ETDEWEB)

Potts, A

1998-04-01

Recent developments in conveyor systems have focused on accessories rather than the belt itself. Radio frequency identification (RFID) is a technology using transponders embedded in conveyor belts and this is the latest development at the German firm Contitech. The system described in the articles developed with Moers, features transponders for cooling, controlling and monitoring conveyor belts. Other developments mentioned include a JOKI drum motor featuring a fully integrated gearbox and electric motor enclosed in a steel shell, from Interoll; a new scraper cleaning system from Hosch, new steel cord belting from Fenner, a conveying system for Schleenhain lignite opencast mine by FAM Foerdelantigen Magdeburg; new bearings from Nadella (the sales arm of Intersoll-Rand), an anti-shock belt transfer table from Rosta and new caliper disc brakes from GE Industrial.

Idealized debris flow in flume with bed driven by a conveyor belt

Science.gov (United States)

Ling, Chi-Hai; Chen, Cheng-lung

1989-01-01

The generalized viscoplastic fluid (GVF) model is used to derive the theoretical expressions of two-dimensional velocities and surface profile for debris flow established in a flume with bed driven by a conveyor belt. The rheological parameters of the GVF model are evaluated through the comparison of theoretical results with measured data. A slip velocity of the established (steady) nonuniform flow on the moving bed (i.e., the conveyor belt) is observed, and a relation between the slip velocity and the velocity gradient at the bed is derived. Two belts, one rough and the other smooth, were tested. The flow profile in the flume is found to be linear and dependent on the roughness of the belt, but not much on its speed.

Design of temperature detection device for drum of belt conveyor

Science.gov (United States)

Zhang, Li; He, Rongjun

2018-03-01

For difficult wiring and big measuring error existed in the traditional temperature detection method for drum of belt conveyor, a temperature detection device for drum of belt conveyor based on Radio Frequency(RF) communication is designed. In the device, detection terminal can collect temperature data through tire pressure sensor chip SP370 which integrates temperature detection and RF emission. The receiving terminal which is composed of RF receiver chip and microcontroller receives the temperature data and sends it to Controller Area Network(CAN) bus. The test results show that the device meets requirements of field application with measuring error ±3.73 ° and single button battery can provide continuous current for the detection terminal over 1.5 years.

This conveyor belt in a tube is a coal-heaver's dream

Energy Technology Data Exchange (ETDEWEB)

Gregorie, D

1986-01-01

This article describes a piece of equipment used for the handling of coal. Several of these tubulators have been installed in boiler houses in New Zealand. The tubulator is a conveyor belt in a tube and its details are presented. The innovative features of the conveyor are listed along with its advantages over existing systems.

Determination of acceleration for belt conveyor speed control in transient operation

NARCIS (Netherlands)

He, D.; Pang, Y.; Lodewijks, G.

2016-01-01

Speed control has been found a feasible mean to reduce the energy consumption of belt conveyors. However, the current research has not taken the determination of the acceleration in transient operation into account sufficiently. With respect to the belt tension rating, demanded safety factor and the

Survival of Listeria monocytogenes on a conveyor belt material with or without antimicrobial additives

OpenAIRE

Chaitiemwong, N.; Hazeleger, W.C.; Beumer, R.R.

2010-01-01

Survival of Listeria monocytogenes on a conveyor belt material with or without antimicrobial additives, in the absence or presence of food debris from meat, fish and vegetables and at temperatures of 10, 25 and 37 °C was investigated. The pathogen survived best at 10 °C, and better at 25 °C than at 37 °C on both conveyor belt materials. The reduction in the numbers of the pathogen on belt material with antimicrobial additives in the first 6 h at 10 °C was 0.6 log unit, which was significantly...

Influence of some design and operating parameters of conveyor with suspended belt and distributed drive on the technical specifications

Directory of Open Access Journals (Sweden)

Tolkachev E.N.

2017-03-01

Full Text Available The influence of several design and operating parameters of conveyor on the individual components of the stretching tension in the belt of conveyor with suspended belt and distributed drive was analyzed. The analysis of influence a number design and operating parameters on the technical specifications of conveyor with suspended belt and distributed drive was done. Recommendations on the choice of rational parameters were formulated.

Influence of some design and operating parameters of conveyor with suspended belt and distributed drive on the technical specifications

OpenAIRE

Tolkachev E.N.

2017-01-01

The influence of several design and operating parameters of conveyor on the individual components of the stretching tension in the belt of conveyor with suspended belt and distributed drive was analyzed. The analysis of influence a number design and operating parameters on the technical specifications of conveyor with suspended belt and distributed drive was done. Recommendations on the choice of rational parameters were formulated.

Method of modifying conveyor belt profile for monitoring ask content of coarse grain coal by radiometric methods

International Nuclear Information System (INIS)

Taborsky, J.; Tryzna, P.; Formanek, Z.; Vales, J.

1982-01-01

The conveyor belt is gripped in the chosen place with benches to form a V shape with a constant cross section independent of the immediate amount of transported coal. At this point the source and the radiation intensity monitor are placed in horizontal plane on the sides of the conveyor belt. Their connecting line is perpendicular to the direction of the movement of the conveyor belt. Thus, monitoring of the ash content of mined coal and operative control of mining according to measured values are made possible. (Ha)

Nano-optical conveyor belt with waveguide-coupled excitation.

Science.gov (United States)

Wang, Guanghui; Ying, Zhoufeng; Ho, Ho-pui; Huang, Ying; Zou, Ningmu; Zhang, Xuping

2016-02-01

We propose a plasmonic nano-optical conveyor belt for peristaltic transport of nano-particles. Instead of illumination from the top, waveguide-coupled excitation is used for trapping particles with a higher degree of precision and flexibility. Graded nano-rods with individual dimensions coded to have resonance at specific wavelengths are incorporated along the waveguide in order to produce spatially addressable hot spots. Consequently, by switching the excitation wavelength sequentially, particles can be transported to adjacent optical traps along the waveguide. The feasibility of this design is analyzed using three-dimensional finite-difference time-domain and Maxwell stress tensor methods. Simulation results show that this system is capable of exciting addressable traps and moving particles in a peristaltic fashion with tens of nanometers resolution. It is the first, to the best of our knowledge, report about a nano-optical conveyor belt with waveguide-coupled excitation, which is very important for scalability and on-chip integration. The proposed approach offers a new design direction for integrated waveguide-based optical manipulation devices and its application in large scale lab-on-a-chip integration.

Estimation of Rheological Properties of Viscous Debris Flow Using a Belt Conveyor

Science.gov (United States)

Hübl, J.; Steinwendtner, H.

2000-09-01

Rheological parameters of viscous debris flows are influenced by a great amount of factors and are therefore extremely difficult to estimate. Because of this uncertainties a belt conveyor (conveyor channel) was constructed to measure flow behaviour and rheological properties of natural debris flow material. The upward movement of the smooth rubberised belt between fixed lateral plastic walls causes a stationary wave relative to these bends. This special experimental design enables to study behaviour of viscous ebris flow material with maximum grain diameters up to 20 mm within several minutes and to hold measuring equipment very simple. The conveyor channel was calibrated first with Xanthan, a natural polysaccharide used as thickener in food technology, whose rheological properties are similar to viscous debris flow material. In a second step natural debris flow material was investigated. Velocities and rheological parameters were measured with varying solid concentration and slope of the channel. In cases where concentration of coarse particles exceed around 15% by volume the conveyor channel obtains an alternative to expensive commercial viscometers for determination of rheological parameters of viscous debris flows.

Minimising the fire hazard from the use of belt conveyors in intake roadways

Energy Technology Data Exchange (ETDEWEB)

Leeming, J.R. [Health and Safety Executive, Sheffield, S. Yorkshire (United Kingdom)

2010-07-01

The fire that occurred a the Creswell underground coal mine in Derbyshire in 1950 in which 90 miners lost their lives was caused by a damaged rubber conveyor belt that ignited after being friction heated. The fire propagated along the intake trunk roadway by the burning belt itself, which ignited the timber roadway supports and hampered fire-fighting efforts. This paper demonstrated that operating conveyors in intake trunk roadways presents a risk that products of combustion can be carried to the working areas of a mine via ventilation pathways, thus creating a hazard to the underground miners. In North America, the use of belt air is not commonly used to ventilate working areas. However, these arrangements are common in the United Kingdom. As such, installation, inspection and maintenance standards have been created to minimize the risk of fire in underground, remotely operated belt conveyors in underground mines. Monitoring systems are also in place for early detection of any fire. A review of recent underground fires in the United Kingdom has shown that the measures adopted have been successful in avoiding uncontrollable fires. 13 refs., 5 figs.

Application of Failure Mode Effect and Criticality Analysis (FMECA to a Computer Integrated Manufacturing (CIM Conveyor Belt

Directory of Open Access Journals (Sweden)

I. Elbadawi

2018-06-01

Full Text Available Fault finding and failure predicting techniques in manufacturing and production systems often involve forecasting failures, their effects, and occurrences. The majority of these techniques predict failures that may appear during the regular system production time. However, they do not estimate the failure modes and they require extensive source code instrumentation. In this study, we suggest an approach for predicting failure occurrences and modes during system production time intervals at the University of Hail (UoH. The aim of this project is to implement failure mode effect and criticality analysis (FMECA on computer integrated manufacturing (CIM conveyors to determine the effect of various failures on the CIM conveyor belt by ranking and prioritizing each failure according to its risk priority number (RPN. We incorporated the results of FMECA in the development of formal specifications of fail-safe CIM conveyor belt systems. The results show that the highest RPN values are for motor over current failure (450, conveyor chase of vibration (400, belt run off at the head pulley (200, accumulated dirt (180, and Bowed belt (150. The study concludes that performing FMECA is highly effective in improving CIM conveyor belt reliability and safety in the mechanical engineering workshop at UoH.

Impact of Selected Parameters on the Fatigue Strength of Splices on Multiply Textile Conveyor Belts

Science.gov (United States)

Bajda, Mirosław; Błażej, Ryszard; Hardygóra, Monika

2016-10-01

Splices are the weakest points in the conveyor belt loop. The strength of these joints, and thus their design as well as the method and quality of splicing, determine the strength of the whole conveyor belt loop. A special zone in a splice exists, where the stresses in the adjacent plies or cables differ considerably from each other. This results in differences in the elongation of these elements and in additional shearing stresses in the rubber layer. The strength of the joints depends on several factors, among others on the parameters of the joined belt, on the connecting layer and the technology of joining, as well as on the materials used to make the joint. The strength of the joint constitutes a criterion for the selection of a belt suitable for the operating conditions, and therefore methods of testing such joints are of great importance. This paper presents the method of testing fatigue strength of splices made on multi-ply textile conveyor belts and the results of these studies.

Modelling of Conveyor Belt Passage by Driving Drum Using Finite Element Methods

Directory of Open Access Journals (Sweden)

Nikoleta Mikušová

2017-12-01

Full Text Available The finite element methods are used in many disciplines by the development of products, typically in mechanical engineering (for example in automotive industry, biomechanics, etc.. Some modern programs of the finite element's methods have specific tools (electromagnetic, fluid and structural simulations. The finite elements methods allow detailed presentation of structures by bending or torsion, complete design, testing and optimization before the prototype production. The aims of this paper were to the model of conveyor belt passage by driving drum. The model was created by the program Abaqus CAE. The created model presented data about forces, pressures, and deformation of the belt conveyor.

Mobile belt conveyor

OpenAIRE

Tenora, Jiří

2017-01-01

Cílem bakalářské práce je návrh pásového dopravníku pro přepravu drobného kameniva, zeminy a drobné stavební sutě s dopravním výkonem 60 t/h, výškovým rozdílem 3,5 m a vzdáleností mezi osami bubnů 8 m. Tato práce obsahuje také popis základních částí pásového dopravníku, funkční výpočty podle normy ČSN ISO 5048, návrh hlavních rozměrů dopravníku a pohonu. Celá práce se skládá z technické zprávy a výkresové dokumentace. The aim of this word is to design belt conveyor to transport tiny aggreg...

Design of Online Monitoring and Fault Diagnosis System for Belt Conveyors Based on Wavelet Packet Decomposition and Support Vector Machine

Directory of Open Access Journals (Sweden)

Wei Li

2013-01-01

Full Text Available Belt conveyors are the equipment widely used in coal mines and other manufacturing factories, whose main components are a number of idlers. The faults of belt conveyors can directly influence the daily production. In this paper, a fault diagnosis method combining wavelet packet decomposition (WPD and support vector machine (SVM is proposed for monitoring belt conveyors with the focus on the detection of idler faults. Since the number of the idlers could be large, one acceleration sensor is applied to gather the vibration signals of several idlers in order to reduce the number of sensors. The vibration signals are decomposed with WPD, and the energy of each frequency band is extracted as the feature. Then, the features are employed to train an SVM to realize the detection of idler faults. The proposed fault diagnosis method is firstly tested on a testbed, and then an online monitoring and fault diagnosis system is designed for belt conveyors. An experiment is also carried out on a belt conveyor in service, and it is verified that the proposed system can locate the position of the faulty idlers with a limited number of sensors, which is important for operating belt conveyors in practices.

A Comparison of Effective Tension Calculation for Design Belt Conveyor between CEMA and DIN Standard

Directory of Open Access Journals (Sweden)

Satria Iman

2018-01-01

Full Text Available In the present era, many industries are demanding material transfer equipment that works maximally and cheaply. Belt Conveyor is one of the most efficient material transfer equipment compared to heavy equipment or other transportation equipment, because it can transport the material in large capacity. When designing conveyor belts, many industries want large transport capacity at low cost. One of the cost savings can be done with low motor power consumption. Many standards describe the effective tension calculation on the conveyor belt in detail with the parameters, since the effective tension calculation results are essential for determining motor power. This paper aims to analyze the effective tension on conveyor belts using CEMA 5th, CEMA 6th and DIN 22101 standards with case studies of 1000 TPH carrying capacity and 3 m/s conveyor speed. The difference between CEMA and DIN when determining the effective tension is on the use of coefficient of friction, because DIN uses a global coefficient of friction while CEMA uses different friction coefficients on idler, belt and material. This difference in coefficient of friction results in different ways of calculating the resistance being the accumulation of the effective tension. The result is an effective tension value using DIN 22101 standard of 22,148.16 N with motor power consumption of 66.5 kW, while effective tension value using CEMA 5th standard is 32.201.66 N with motor power consumption 96.47 kW, and effective tension value using CEMA 6th standard is 29,686.48 N with 89.06 kW motor power consumption.

Start-up of belt conveyors used for haulage of large lumps under difficult climatic conditions

Energy Technology Data Exchange (ETDEWEB)

Drobny, J

1979-01-01

Investigations are discussed carried out by the Research and Development Center for Brown Coal in Most, Czechoslovakia into effects of climate, weather and mass of coal lumps on reliability of belt conveyors in surface mines. Dirt buildup on the driving drums reduces friction and increases belt sliding hazards. Belt wear increases. Driving drum diameter, increased by the buildup, negatively influences load distribution among the electric motors of the drive system. In extreme cases belt wear and irregular load distribution cause belt failures. Methods for buildup removal used in Czechoslovakia and methods for protection of the return side of a conveyor are described. Effects of large mass of coal lumps and ice buildup on large lumps on the risk of belt damage (cuts, punctures etc,) are discussed. Recommendations for design of coal transfer points are made. 2 refs.

Transport of mass goods on the top run and bottom run of belt conveyors

Energy Technology Data Exchange (ETDEWEB)

Zimmermann, D

1977-06-01

For combined coal winning from the collieries 'General Blumenthal' and 'Ewald Fortsetzung' a large belt conveyor plant was taken into operation which is able to transport 1360 tons/h in the top run and 300 tons/h of dirt in the bottom run. The different types of coal are transported separately in intermittent operation with the aid of bunker systems connected to the front and rear of the belt conveyor. Persons can be transported in the top run as well as in the bottom run.

Application of the method finite elements by numerical modeling stress-strain state in conveyor belts

OpenAIRE

Maras Michal; Hatala Jozef; Marasová Daniela

1997-01-01

Solving problems connected with damaging a conveyor belt at the transfer points is conditioned by knowing laws of this phenomenon. Acquiring the knowledge on this phenomen is possible to be gained either by experimental research or by the numerical model GEM 22, which enables to determine the distribution of stresses and strains in a suitably selected cross-section of a conveyor belt. The paper begins by defining the problem, determining the boundary model conditions and continues by modellin...

Fabrication and Operation of a Nano-Optical Conveyor Belt.

Science.gov (United States)

Ryan, Jason; Zheng, Yuxin; Hansen, Paul; Hesselink, Lambertus

2015-08-26

The technique of using focused laser beams to trap and exert forces on small particles has enabled many pivotal discoveries in the nanoscale biological and physical sciences over the past few decades. The progress made in this field invites further study of even smaller systems and at a larger scale, with tools that could be distributed more easily and made more widely available. Unfortunately, the fundamental laws of diffraction limit the minimum size of the focal spot of a laser beam, which makes particles smaller than a half-wavelength in diameter hard to trap and generally prevents an operator from discriminating between particles which are closer together than one half-wavelength. This precludes the optical manipulation of many closely-spaced nanoparticles and limits the resolution of optical-mechanical systems. Furthermore, manipulation using focused beams requires beam-forming or steering optics, which can be very bulky and expensive. To address these limitations in the system scalability of conventional optical trapping our lab has devised an alternative technique which utilizes near-field optics to move particles across a chip. Instead of focusing laser beams in the far-field, the optical near field of plasmonic resonators produces the necessary local optical intensity enhancement to overcome the restrictions of diffraction and manipulate particles at higher resolution. Closely-spaced resonators produce strong optical traps which can be addressed to mediate the hand-off of particles from one to the next in a conveyor-belt-like fashion. Here, we describe how to design and produce a conveyor belt using a gold surface patterned with plasmonic C-shaped resonators and how to operate it with polarized laser light to achieve super-resolution nanoparticle manipulation and transport. The nano-optical conveyor belt chip can be produced using lithography techniques and easily packaged and distributed.

Persistence of Salmonella on egg conveyor belts is dependent on the belt type but not on the rdar morphotype.

Science.gov (United States)

Stocki, S L; Annett, C B; Sibley, C D; McLaws, M; Checkley, S L; Singh, N; Surette, M G; White, A P

2007-11-01

Commercial caged layer flocks in Alberta, Canada, are commonly monitored for Salmonella enterica serovar Enteritidis (SE) and S. enterica serovar Typhimurium (ST) by environmental sampling. In one recent case, a SE strain isolated from the egg conveyor belt was a source of persistent infection for the flock. This study was undertaken to examine Salmonella colonization on egg conveyor belts and to determine whether the rdar morphotype, a conserved physiology associated with aggregation and long-term survival, contributed to persistence. Four woven belts constructed of natural or nonnatural fibers and a 1-piece belt made of vinyl were tested with rdar-positive ST and SE strains and a rdar-negative ST DeltaagfD reference strain. The type of egg belt was the most important factor influencing Salmonella colonization and persistence. The vinyl belt, with the least surface area available for colonization, had the fewest Salmonella remaining after washing and disinfection, whereas the hemp-plastic belt, with the greatest surface area, had the most Salmonella remaining. Real-time gene expression indicated that the rdar morphotype was involved in colonizing the egg belt pieces; however, it was not essential for persistence. In addition, rdar-positive and rdar-negative strains were equally similarly to disinfection on the egg belt pieces. The results indicate that Salmonella can persist on a variety of egg belts by mechanisms other than the rdar morphotype, and that using egg conveyer belts with reduced surface area for bacterial colonization can lessen contamination problems.

Device for determining the content of bulk materials on conveyor belts

International Nuclear Information System (INIS)

Fritsche, D.

1983-01-01

On the basis of the forward scattering of photon radiation the invention is aimed at determining the content of bulk material, in particular the ash content of lignite, independently of the height of the material conveyed by belts. This could be achieved by making the radiation source support movable, so that the distance between source and conveyor belt is variable and adaptable to the mean height of the bulk material

The energy-saving design of belt conveyors. Energiesparende Auslegung von Gurtfoerderanlagen

Energy Technology Data Exchange (ETDEWEB)

Greune, A

1989-01-01

The examination of the factors affecting the main resistance on an experimental belt conveyor was carried out by varying the velocity and tension of the belt, the diameter of the carrying idlers and the distance between them, and, for the first time, this examination was performed on different belts with different covers. The influences of the varied parameters for the proportions of main resistance, frictional resistance due to imprint, belt flexing resistance and the rotational resistance of the idlers were recorded with the use of formulae and were graphically represented. For the entire relative main resistance referred to 1 m plant length it was possible to obtain a minimum for a particular combination of parameters, and further recommendations for the energy-saving design of belt conveyors were deduced from this. The joint goals of reducing the load-dependence of the rotational resistance and of improving the reliability of seals, at the same time keeping the number of parts to a minimum and making assembly simple, formed the focal point of examination into the possibilities of improving the construction of carrying idlers. Thus, individual components and alternative constructions were examined on a test bench for measuring the rotational resistance as well as on a test bench for seals, and indications for the design of individual assembly groups were developed from this. (orig.).

Condition-orientated servicing and maintenance of large belt conveyor systems. Examples from the management of belt conveyors and idler rollers in the Rhenish brown coal district; Zustandsorientierte Wartung und Instandhaltung von Grossbandanlagen. Beispiele aus der Foerdergurt- und Bandtragrollenbewirtschaftung im rheinischen Braunkohlenrevier

Energy Technology Data Exchange (ETDEWEB)

Jansen, Marcus [RWE Power Aktiengesellschaft, Frechen (Germany). Technikzentrum Tagebaue/Maschinentechnik/Foerdergurte

2009-04-28

The belt conveyor systems and in particular the products used on them, viz. 'conveyor belts and idler rollers', are highly relevant to the costs of maintenance and strategically important for the system availability in open-cast mines. The measures described show how new technologies and methods are integrated in the open-cast mining processes. Conveyors, machines and tools are optimised and further developed within the framework of a continuous improvement process in order to meet more stringent requirements. Comparable further development and adaptation of new technologies takes place on all defined products. (orig.)

Diagnostics of Technical Condition of Gear Units of Belt Conveyors for the Aggregate of Methods of Nondestructive Testing

Science.gov (United States)

Kuzin, Evgeny G.; Gerike, Boris L.; Drozdenko, Yuriy V.; Lupiy, Michael G.; Grigoryeva, Natalya V.

2017-10-01

The article reviews the issues of complex use of methods of technical diagnostics of gearboxes for belt conveyors, with the aim of creating an effective system of maintenance. The article is showing the results of the evaluation of the technical condition of the drives of belt conveyors based on vibration monitoring and thermal parameters, and analysis of lubricating oil.

The impact of the provisions of the suspensions on the track of conveyor with suspended belt and distributed drive at jamming rollers

Directory of Open Access Journals (Sweden)

Tolkachev E.N.

2018-03-01

Full Text Available The article is devoted to the topical issue, which is related to simulation of the failures of drives suspensions of the conveyor with suspended belt and distributed drive. Using the developed mathematical model of the failures drives suspensions due to jamming rollers to the reference design of conveyor with suspended belt and distributed drive is performed modelling of dynamic characteristics. Investigation of the influence of the location of the failed drives suspensions on the track on the main technical characteristics of the conveyor belt with suspended belt was carried out.

Research of x-ray nondestructive detector for high-speed running conveyor belt with steel wire ropes

Science.gov (United States)

Wang, Junfeng; Miao, Changyun; Wang, Wei; Lu, Xiaocui

2008-03-01

An X-ray nondestructive detector for high-speed running conveyor belt with steel wire ropes is researched in the paper. The principle of X-ray nondestructive testing (NDT) is analyzed, the general scheme of the X-ray nondestructive testing system is proposed, and the nondestructive detector for high-speed running conveyor belt with steel wire ropes is developed. The hardware of system is designed with Xilinx's VIRTEX-4 FPGA that embeds PowerPC and MAC IP core, and its network communication software based on TCP/IP protocol is programmed by loading LwIP to PowerPC. The nondestructive testing of high-speed conveyor belt with steel wire ropes and network transfer function are implemented. It is a strong real-time system with rapid scanning speed, high reliability and remotely nondestructive testing function. The nondestructive detector can be applied to the detection of product line in industry.

Dynamic modelling and simulation of complex drive systems of large belt conveyors; Dynamische Modellierung und Simulation komplexer Antriebssysteme von Grossbandanlagen

Energy Technology Data Exchange (ETDEWEB)

Burgwinkel, Paul; Vreydal, Daniel; Eltaliawi, Gamil; Vijayakumar, Nandhakumar [RWTH Aachen (DE). Inst. fuer Maschinentechnik der Rohstoffindustrie (IMR)

2010-09-15

For the first time the Co-simulation method was successfully used for full representation of a large belt conveyor for an open cast mine in a simulation model at the Institute for Mechanical Engineering in the Raw Materials Industry at Rhineland-Westphalia Technological University in Aachen. The aim of this project was the development of an electro-mechanical simulation model, which represents all components of a large belt conveyor from the drive motor to the conveyor belt in one simulation model and thus makes the interactions between the individual assemblies verifiable by calculations. With the aid of the developed model it was possible to determine critical operating speeds of the represented large belt conveyor and derive suitable measures to combat undesirable resonance states in the drive assembly. Furthermore it was possible to clarify the advantage of the full numerical representation of an electromechanical drive system. (orig.)

Modelling of the Flow of Streams of Cohesionless and Cohesive Bulk Materials in a Conveyor Discharge Point with a Flat Conveyor Belt

Science.gov (United States)

Cyganiuk, J. A.; Kuryło, P.

2018-02-01

The paper presents the analysis of flow conditions of cohesive and cohesionless bulk materials in a conveyor discharge point of a flat conveyor belt. The analysis was carried out for stationary flows at high velocities. It presents mathematical methods for the description of the velocity of a material leaving a throwing point of a flat conveyor belt as well as final equations which enable the determination of velocity of the material after it has left the throwing point (with the accuracy sufficient for practical use). Next, the velocity calculated for the proposed mathematical description (for selected material groups) has been compared with the velocity obtained from mathematical relations commonly used by engineers. The proposed equations for determining the velocity of the material beyond the point have proved useful, since they enable excluding the indirect equations. Finally, the difference between the values of the velocity obtained with the proposed and indirect equations have been determined and the relative error for the proposed method has been calculated.

The Design of RFID Conveyor Belt Gate Systems Using an Antenna Control Unit

Directory of Open Access Journals (Sweden)

Ki Hwan Eom

2011-09-01

Full Text Available This paper proposes an efficient management system utilizing a Radio Frequency Identification (RFID antenna control unit which is moving along with the path of boxes of materials on the conveyor belt by manipulating a motor. The proposed antenna control unit, which is driven by a motor and is located on top of the gate, has an array structure of two antennas with parallel connection. The array structure helps improve the directivity of antenna beam pattern and the readable RFID distance due to its configuration. In the experiments, as the control unit follows moving materials, the reading time has been improved by almost three-fold compared to an RFID system employing conventional fixed antennas. The proposed system also has a recognition rate of over 99% without additional antennas for detecting the sides of a box of materials. The recognition rate meets the conditions recommended by the Electronic Product Code glbal network (EPCglobal for commercializing the system, with three antennas at a 20 dBm power of reader and a conveyor belt speed of 3.17 m/s. This will enable a host of new RFID conveyor belt gate systems with increased performance.

Condition-Based Conveyor Belt Replacement Strategy in Lignite Mines with Random Belt Deterioration

Science.gov (United States)

Blazej, Ryszard; Jurdziak, Leszek

2017-12-01

In Polish lignite surface mines, condition-based belt replacement strategies are applied in order to assure profitable refurbishment of worn out belts performed by external firms specializing in belt maintenance. In two of three lignite mines, staff asses belt condition subjectively during visual inspections. Only one mine applies specialized diagnostic device (HRDS) allowing objective magnetic evaluation of belt core condition in order to choose the most profitable moment for the dismantling of worn out belt segments from conveyors and sending them to the maintenance firm which provides their refurbishment. This article describes the advantages of a new diagnostic device called DiagBelt. It was developed at the Faculty of Geoengineering, Mining and Geology, Wroclaw University of Science and Technology. Economic gains from its application are calculated for the lignite mine and for the belt maintenance firm, taking into account random life (durability) of new and reconditioned belts (after the 1st and the 2nd refurbishment). Recursive calculations for following years allow the estimation of the length and costs of replaced, reconditioned and purchased belts on an annual basis, while the use of the Monte Carlo method allows the estimation of their variability caused by random deterioration of belts. Savings are obtained due to better selection of moments (times) for the replacement of belt segments and die to the possibility to qualify worn out belts for refurbishment without the need to remove their covers. In effect, increased belt durability and lowered share of waste belts (which were not qualified for reconditioning) create savings which can quickly cover expenditures on new diagnostic tools and regular belt inspections in the mine.

Efficacy of ultraviolet light exposure against survival of Listeria monocytogenes on conveyor belts.

Science.gov (United States)

Morey, Amit; McKee, Shelly R; Dickson, James S; Singh, Manpreet

2010-06-01

Listeria monocytogenes has been repeatedly isolated from foods and food-processing facilities including food contact surfaces such as conveyor belts (CB). CBs are often difficult to clean and require rigorous sanitation programs for decontamination. Ultraviolet (UV) light has exhibited microbicidal properties on food contact surfaces and this study was conducted to determine the efficacy of UV against L. monocytogenes on CB made of different materials. A four-strain cocktail of L. monocytogenes (serotypes 3A, 4A, 4B, and 4C) was made to give a suspension of approximately 10(7) CFU/mL. CBs made from four different types of materials, (1) Ropanyl DM 8/2 A2 + 04 (belt 1), (2) Volta FRMW-3.0 (belt 2), (3) Volta FRMB-3.0 (belt 3), and (4) Ropanyl DM (belt 4), were inoculated with 1 mL of the four-strain cocktail (approximately 10(7) CFU/mL) of the bacterial suspension. CBs were treated with UV light (254 nm) for 1 and 3 sec at 5.53 and 5.95 mW/cm(2). Three replications of the experiments were conducted. Two-way analysis of variance of survival populations of L. monocytogenes showed that bacterial counts were significantly reduced (p belt types irrespective of UV light intensities and times of exposure. L. monocytogenes populations were reduced (p belts 1, 2, and 3 after exposure to 5.95 mW/cm(2) UV light intensity for 3 sec. L. monocytogenes-inoculated CBs that were exposed to 5.53 mW/cm(2) showed higher (p Belt 4 showed survival populations of L. monocytogenes ranging from 1.42 to 1.73 log(10) CFU/cm(2) after UV light treatment for 1 and 3 sec. UV light can be effectively used to reduce L. monocytogenes contamination on CBs.

THE HARMONIZATION AND OPTIMIZATION OF DIAGNOSTIC METHODS FOR A BELT CONVEYOR

Directory of Open Access Journals (Sweden)

František HELEBRANT

2012-04-01

Full Text Available The final aim of the project MPO FR‐T11/537 called “The Complex Diagnostic System for the Belt Transport” is a single part custom manufacturing and sale of complex diagnostic system for belt transportation and related services. The output of the project is a prototype of a diagnostic system on a model belt conveyor with prepared and certified diagnostic services and methods including their measurements and other supportive tools. The article will introduce the present state of the solution for the given grant project, especially in the field of suggested work on the diagnostic and supportive methods and other measurements.

Nano-optical conveyor belt, part I: Theory.

Science.gov (United States)

Hansen, Paul; Zheng, Yuxin; Ryan, Jason; Hesselink, Lambertus

2014-06-11

We propose a method for peristaltic transport of nanoparticles using the optical force field over a nanostructured surface. Nanostructures may be designed to produce strong near-field hot spots when illuminated. The hot spots function as optical traps, separately addressable by their resonant wavelengths and polarizations. By activating closely packed traps sequentially, nanoparticles may be handed off between adjacent traps in a peristaltic fashion. A linear repeating structure of three separately addressable traps forms a "nano-optical conveyor belt"; a unit cell with four separately addressable traps permits controlled peristaltic transport in the plane. Using specifically designed activation sequences allows particle sorting.

Linear Motor for Drive of Belt Conveyor

Directory of Open Access Journals (Sweden)

Milan Krasl

2006-01-01

Full Text Available This paper introduces a novel approach on the design of a linear motor for drive of belt conveyor (LMBC. The motor is a simple combination of asynchronous motor in plane. The electromagnetic forces is one of the most important parameters of electrical machines. This parameter is necessary for the checking of the design. This paper describes several variants: linear motor with slots in platens, slots in one half of platens and optimization of slots. The electromagnetic force can be found with the help of a Finite Elements Method – based program. For solution was used QuickField program.

Designing on-line analyzer for coal on belt conveyor using neutron activation technique

International Nuclear Information System (INIS)

Rony Djokorayono; Agus Cahyono

2014-01-01

Basic design of on-line analyzer for coal on belt conveyor using neutron activation technique has been carried out. Compared with sampling technique, this neutron activation technique has some advantages in term of analysis accuracy and time. The design activities performed include the establishment of design requirements, functional requirements, technical requirements, technical specification, detection sub-system design, data acquisition subsystem design, and operator computer console design. This program will use Nal(Tl) scintillation detector to detect gamma-rays emitted by elements in coal due to neutron activation of a neutron source, "2"5"2Cf (Californium-252). This basic design of on-line analyzer for coal on belt conveyor using neutron activation technique should be followed up with the development of detailed design, prototype construction, and field testing. (author)

OPTIMUM DESIGN AND COST CHARACTERISTIC OF SMALL CONVEYOR

OpenAIRE

Suwat Nanetoe; Nitipong Soponpongpipat

2013-01-01

Although there are many works dealing with the economic analysis of a long conveyor, the information about a short conveyor is insufficient. This study, thus, deals with the short conveyor by studying the effect of belt width, belt length, convey capacity, and conveyor inclination angle on the cost characteristic of short conveyor. The study was done by calculating the conveyor belt widths and their supports that could service a given convey capacity, conveyor length, and inclination angle. T...

The Question of Energy-Efficient Design of the Automated Electric Drive of Multi-Engine Belt Conveyors

Directory of Open Access Journals (Sweden)

Semykina Irina

2015-01-01

Full Text Available The article proposes a method for improving the energy efficiency of multi-motor variable frequency electric drives of trunk belt conveyors, based on the conveyor speed changing and controlling of the magnetic state of the motor. At conclusion, economic and energy effects of the implementation are estimated.

Range camera on conveyor belts: estimating size distribution and systematic errors due to occlusion

Science.gov (United States)

Blomquist, Mats; Wernersson, Ake V.

1999-11-01

When range cameras are used for analyzing irregular material on a conveyor belt there will be complications like missing segments caused by occlusion. Also, a number of range discontinuities will be present. In a frame work towards stochastic geometry, conditions are found for the cases when range discontinuities take place. The test objects in this paper are pellets for the steel industry. An illuminating laser plane will give range discontinuities at the edges of each individual object. These discontinuities are used to detect and measure the chord created by the intersection of the laser plane and the object. From the measured chords we derive the average diameter and its variance. An improved method is to use a pair of parallel illuminating light planes to extract two chords. The estimation error for this method is not larger than the natural shape fluctuations (the difference in diameter) for the pellets. The laser- camera optronics is sensitive enough both for material on a conveyor belt and free falling material leaving the conveyor.

Using the classical linear regression model in analysis of the dependences of conveyor belt life

Directory of Open Access Journals (Sweden)

Miriam Andrejiová

2013-12-01

Full Text Available The paper deals with the classical linear regression model of the dependence of conveyor belt life on some selected parameters: thickness of paint layer, width and length of the belt, conveyor speed and quantity of transported material. The first part of the article is about regression model design, point and interval estimation of parameters, verification of statistical significance of the model, and about the parameters of the proposed regression model. The second part of the article deals with identification of influential and extreme values that can have an impact on estimation of regression model parameters. The third part focuses on assumptions of the classical regression model, i.e. on verification of independence assumptions, normality and homoscedasticity of residuals.

Application of cool wan flow control weight scale design on belt conveyor

International Nuclear Information System (INIS)

Djokorayono, Rony; Junus; Rivai, A; Gunarwan; Indarzah

2003-01-01

Control of the coal mass flow on the belt conveyor at coal handling unit PLTU Suralaya has been designed by using weight scale of gamma absorption technique where accuracy for the measurement of weight scale system is 0,5% to 0,1%. The absorption gamma radiation will be measured by scintillation or ion chamber detector

Simulation of the dust suppression process with foam in the areas of belt conveyors

Directory of Open Access Journals (Sweden)

Bespalov Vadim

2017-01-01

Full Text Available The article provides the analysis of the physical essence and simulation of the process of dust retention with foam in the air of working zones of belt conveyors transporting sand, crushed stone, gravel, coal, grain. In accordance with the proposed physical-energy concept of simulation of the process of dust control its physical essence is in a deliberate sequential action on the dust particles with previously prepared by the parameters external (additional dispersed systems. Use of dust retention technology foam method provides high efficiency of reducing the concentration of dust in the air of working areas of belt conveyors, which varies in the range of 85.0–99.0 %, which provides the standard level of dust contamination (MPC in air of working areas of listed industrial sources of formation and emission of dust.

Automatic sampling technology in wide belt conveyor with big volume of coal flow

Energy Technology Data Exchange (ETDEWEB)

Liu, J. [China Coal Research Institute, Beijing (China)

2008-06-15

The principle and technique of sampling in a wide belt conveyor with high coal flow was studied. The design method of the technology, the key parameters, the collection efficiency, the mechanical unit, power supply and control system and worksite facility were ascertained. 3 refs., 5 figs.

INFLUENCE CONSTRUCTION OF THE ROLLER ON THE POWER OF THE DRIVE SYSTEM OF THE BELT CONVEYOR

Directory of Open Access Journals (Sweden)

Tadeusz OPASIAK

2014-09-01

Full Text Available The paper presents a study of new design of rollers. The study focused on the measurement of static and dynamic resistance of rotating rollers and the impact of new construction on the power consumption of the belt conveyor. Rollers have been modified through the use of class C4 bearing seals and labyrinth seal U4Exp 62/65 with a cover 2LU4 of runner construction. Measurements of static and dynamic resistance of rotating rollers were made on a universal rollers stand and power measurements were carried out on a belt conveyor power supply system Gwarek 1200 No. TW in mine KWK Mysłowice–Wesoła.

On the weakly nonlinear, transversal vibrations of a conveyor belt with a low and time-varying velocity

NARCIS (Netherlands)

Suweken, G.; van Horssen, W.T.

2002-01-01

In this paper the weakly nonlinear, transversal vibrations of a conveyor belt will be considered. The belt is assumed to move with a low and time-varying speed. Using Kirchhoff's approach a single equation of motion will be derived from a coupled system of partial differential equations describing

Colloidal Microworms Propelling via a Cooperative Hydrodynamic Conveyor Belt.

Science.gov (United States)

Martinez-Pedrero, Fernando; Ortiz-Ambriz, Antonio; Pagonabarraga, Ignacio; Tierno, Pietro

2015-09-25

We study propulsion arising from microscopic colloidal rotors dynamically assembled and driven in a viscous fluid upon application of an elliptically polarized rotating magnetic field. Close to a confining plate, the motion of this self-assembled microscopic worm results from the cooperative flow generated by the spinning particles which act as a hydrodynamic "conveyor belt." Chains of rotors propel faster than individual ones, until reaching a saturation speed at distances where induced-flow additivity vanishes. By combining experiments and theoretical arguments, we elucidate the mechanism of motion and fully characterize the propulsion speed in terms of the field parameters.

The impact of the provisions of the suspensions on the track of conveyor with suspended belt and distributed drive in violation of the power supply of the drives

Directory of Open Access Journals (Sweden)

Tolkachev E.N.

2017-12-01

Full Text Available The article is devoted to the topical issue, which is related to simulation of the failures of drives suspensions of the conveyor with suspended belt and distributed drive. Using the developed mathematical model of the failures drives suspensions due to the breakage of the electric circuit to the reference design of conveyor with suspended belt and distributed drive is performed modelling of dynamic characteristics. Investigation of the influence of the location of the failed drives suspensions on the track on the main technical characteristics of the conveyor belt with suspended belt was carried out.

Reducing The Risk Of Fires In Conveyor Transport

Science.gov (United States)

Cheremushkina, M. S.; Poddubniy, D. A.

2017-01-01

The paper deals with the actual problem of increasing the safety of operation of belt conveyors in mines. Was developed the control algorithm that meets the technical requirements of the mine belt conveyors, reduces the risk of fires of conveyors belt, and enables energy and resource savings taking into account random sort of traffic. The most effective method of decision such tasks is the construction of control systems with the use of variable speed drives for asynchronous motors. Was designed the mathematical model of the system "variable speed multiengine drive - conveyor - control system of conveyors", that takes into account the dynamic processes occurring in the elements of the transport system, provides an assessment of the energy efficiency of application the developed algorithms, which allows to reduce the dynamic overload in the belt to (15-20)%.

Nano-optical conveyor belt, part II: Demonstration of handoff between near-field optical traps.

Science.gov (United States)

Zheng, Yuxin; Ryan, Jason; Hansen, Paul; Cheng, Yao-Te; Lu, Tsung-Ju; Hesselink, Lambertus

2014-06-11

Optical tweezers have been widely used to manipulate biological and colloidal material, but the diffraction limit of far-field optics makes focused beams unsuitable for manipulating nanoscale objects with dimensions much smaller than the wavelength of light. While plasmonic structures have recently been successful in trapping nanoscale objects with high positioning accuracy, using such structures for manipulation over longer range has remained a significant challenge. In this work, we introduce a conveyor belt design based on a novel plasmonic structure, the resonant C-shaped engraving (CSE). We show how long-range manipulation is made possible by means of handoff between neighboring CSEs, and we present a simple technique for controlling handoff by rotating the polarization of laser illumination. We experimentally demonstrate handoff between a pair of CSEs for polystyrene spheres 200, 390, and 500 nm in diameter. We then extend this technique and demonstrate controlled particle transport down a 4.5 μm long "nano-optical conveyor belt."

Development of a method for the noncontact moisture measurement of different materials at a belt conveyor

International Nuclear Information System (INIS)

Frevert, E.

1991-01-01

In laboratory tests a method was developed for a contactless moisture measurement at belt conveyors of different materials like coal, clay, industrial slay and stones of inflating clay. The moisture was measured with an 241 Am-Be-neutron source, the absolute necessary determination of the changing flow of material was made with the gamma rays of 137 Cs or 241 Am. The analysis of the records shows, that to all measuring values mathematical defined curves could be found, so that methods of calculation for the moisture content could be deduced. The maximal obtainable accuracy is about ± 0.5 percentage by weight. With the industrial slay and the stones of inflating clay supplementary tests were made direct on the belt conveyor. They show, that also in the practice good results can be obtained. (orig.) [de

Modern conveyors move more coal

Energy Technology Data Exchange (ETDEWEB)

Fiscor, S.

2007-10-15

Belt makers and belt designers of underground and overground systems engineer high capacity systems while preparing for new regulations which could reshape how conveyors are designed, probably leading to increased costs. The article reviews developments by manufacturers such as Fenner Dunlop, Continental Conveyor and Equipment Company and Veyance Technologies (previously Goodyear Engineered Products). 3 photos.

Influence analysis of design parameters of suspensions on the technical specifications of conveyor with suspended belt and distributed drive

Directory of Open Access Journals (Sweden)

Lagerev A.V.

2016-09-01

Full Text Available Using the basic design of the conveyor with suspended belt and distributed drive, a series of numerical calculations was performed. As a result, the influence of friction and mass-dimensional design parameters of suspensions on the main technical parameters of the conveyor was established. Recommendations on the choice of rational parameters were formulated.

The impact of the provisions of the suspensions on the track of conveyor with suspended belt and distributed drive at jamming rollers

OpenAIRE

Tolkachev E.N.

2018-01-01

The article is devoted to the topical issue, which is related to simulation of the failures of drives suspensions of the conveyor with suspended belt and distributed drive. Using the developed mathematical model of the failures drives suspensions due to jamming rollers to the reference design of conveyor with suspended belt and distributed drive is performed modelling of dynamic characteristics. Investigation of the influence of the location of the failed drives suspensions on the track on th...

Simulation Method of Designing and Selecting Tensioning Systems for Mining Belt Conveyors

Science.gov (United States)

Kulinowski, Piotr

2014-03-01

This article deals with a methodology developed to design and select tensioning systems with using simulation studies on a belt conveyor model. It describes the structure of a dynamic model of a belt conveyor with distributed parameters and details of physical models of the applied belt tensioning systems. For proper display and comparison of work described tensioning systems are shown examples of the results of simulations carried out on a discrete model of the mining belt conveyor. Presented methodology has been verified through industrial research and realization of a number of complex projects requiring simulation tests of take-up systems of belt conveyors. W artykule przedstawiono symulacyjną metodę projektowania i doboru układów napinania taśmy, wykorzystującą wyniki badań modelowych, będącą często wymaganym rozszerzeniem stosowanych analitycznych metod obliczeniowych (Kulinowski, 2013b). Z uwagi na zjawiska falowe występujące w taśmie podczas nieustalonych stanów pracy przenośników taśmowych, rozruchu, hamowania i pracy przy zmiennej ilości nadawy, wyniki obliczeń uzyskane z wykorzystaniem standardowych metod obliczeniowych można uznać jedynie za szacunkowe lub wstępne do przeprowadzenia badań symulacyjnych. Charakter rozruchu przenośnika taśmowego zależy od typu zastosowanego urządzenia rozruchowego i napinającego, mas wprowadzanych w ruch oraz od własności sprężystych taśmy. Problemy związane z analizą pracy układów napędowych i urządzeń napinających podczas rozruchu przenośników cięgnowych rozwiązano z wykorzystaniem modelu dyskretnego o parametrach rozłożonych (Dolipski et al., 2012; Kulinowski, 2012) opisanego w pierwszej części publikacji. Badania symulacyjne przeprowadzone na takim modelu umożliwiają ocenę pracy przenośnika taśmowego wykorzystującego taśmę z rdzeniem tkaninowym lub stalowym, dlatego też kolejny rozdział artykułu poświęcono modelom reologicznym taśm przeno

Design and commissioning of the 40.10 large belt conveyor; Auslegung und Inbetriebnahme der Grossbandanlage 40.10

Energy Technology Data Exchange (ETDEWEB)

Vatter, H. [Bergwerk Saar, Saarbruecken (Germany); Wiedenroth, J. [Koch Transporttechnik GmbH, Wadgassen (Germany); Keller, K.

2006-03-23

The Saar colliery with an output of 15.000 t saleable output/day is one of the most efficient mines of DSK. In view of the northward migration of the faces and the incorporation of the new Primsmulde field it was necessary to optimise the existing infrastructure of the colliery and adapt it to the new situation. A central element of this optimisation was the new 40.10 conveyor connection. The contribution deals with the design, assembly and commissioning of the 40.10 belt conveyor which is one of the largest conveyors in deep coal mines with an installed power of 6.000 kW. (Orig.)

Survival of Listeria monocytogenes on a conveyor belt material with or without antimicrobial additives

NARCIS (Netherlands)

Chaitiemwong, N.; Hazeleger, W.C.; Beumer, R.R.

2010-01-01

Survival of Listeria monocytogenes on a conveyor belt material with or without antimicrobial additives, in the absence or presence of food debris from meat, fish and vegetables and at temperatures of 10, 25 and 37 °C was investigated. The pathogen survived best at 10 °C, and better at 25 °C than at

The effects of materials' composition and some external factors on measuring precision for nuclear conveyor belt scale

International Nuclear Information System (INIS)

Zhang Yongming; Hong Pingshun; Wang Min

1997-01-01

The effects of some external factors on the metrological precision of a nuclear conveyor belt scale were verified with a series of tests. It is shown that the precision is related not only with the moisture content and composition of the covered materials, but also with the belt's deviation and the evenness of the materials. Mild wind seems to have no effect on the precision

Online analysis of coal on a conveyor belt by use of machine vision and kernel methods

Energy Technology Data Exchange (ETDEWEB)

Aldrich, C.; Jemwa, G.T.; van Dyk, J.C.; Keyser, M.J.; van Heerden, J.H.P. [University of Stellenbosch, Stellenbosch (South Africa). Dept. of Process Engineering

2010-07-01

The objective of this project is to explore the use of image analysis to quantify the amount of fines (6mm) present for different coal samples under conditions simulating the coal on conveyor belts similar to those being used by Sasol for gasification purposes. Quantification of the fines will be deemed particularly successful, if the fines mass fraction, as determined by sieve analysis, is possible to be predicted with an error of less than 10%. In this article, kernel-based methods to estimate particle size ranges on a pilot-scale conveyor belt as well as edge detection algorithms are considered. Preliminary results have shown that the fines fraction in the coal on the conveyor belt could be estimated with a median error of approximately 24.1%. This analysis was based on a relatively small number of sieve samples (18 in total) and needs to be validated by more samples. More samples would also facilitate better calibration and may lead to improved estimates of the sieve fines fractions. Similarly, better results may also be possible by using different approaches to image acquisition and analysis. Most of the error in the fines estimates can be attributed to sampling and to fines that were randomly obscured by the top layer (of larger particles) of coal on the belt. Sampling errors occurred as a result of some breakage of the coal between the sieve analyses and the acquisition of the images. The percentage of the fines obscured by the top layer of the coal probably caused most of the variation in the estimated mass of fines, but this needs to be validated experimentally. Preliminary studies have indicated that some variation in the lighting conditions have a small influence on the reliability of the estimates of the coal fines fractions and that consistent lighting conditions are more important than optimal lighting conditions.

Coherence properties and quantum state transportation in an optical conveyor belt.

Science.gov (United States)

Kuhr, S; Alt, W; Schrader, D; Dotsenko, I; Miroshnychenko, Y; Rosenfeld, W; Khudaverdyan, M; Gomer, V; Rauschenbeutel, A; Meschede, D

2003-11-21

We have prepared and detected quantum coherences of trapped cesium atoms with long dephasing times. Controlled transport by an "optical conveyor belt" over macroscopic distances preserves the atomic coherence with slight reduction of coherence time. The limiting dephasing effects are experimentally identified, and we present an analytical model of the reversible and irreversible dephasing mechanisms. Our experimental methods are applicable at the single-atom level. Coherent quantum bit operations along with quantum state transport open the route towards a "quantum shift register" of individual neutral atoms.

Relocation of belt conveyors along the final slope of the Belacevac surface coal mine

Energy Technology Data Exchange (ETDEWEB)

Maksimovic, N; Rosic, Z

1987-07-01

Describes how following a landslide on the northern wing of the Belacevac surface coal mine the belt conveyor lines had to be relocated in order to assure a reliable coal supply to the Kosovo A and Kosovo B thermal power stations. The relocation was achieved in three phases with new approach cuts being made, necessitating the removal of 280,000 m/sup 3/ of overburden in the first phase and 870,000 m/sup 3/ in the second phase of the reconstruction. Illustrates the relocation of the conveyor system by means of site plans and notes that the production of coal and the removal of overburden were not interrupted during the relocation exercise. 2 refs.

Beyond Accidents : A Back-Analysis on Conveyor Belt Injury for a Better Design for Maintenance Operations

NARCIS (Netherlands)

Martinetti, Alberto; van Dongen, Leonardus Adriana Maria; Romano, Raffaele

2017-01-01

The conveyor belt represents one of the most commonly used methods of transporting bulk materials today. As highlighted multiple times in research, the moving parts are a critical issue causing accidents and injuries and several of these are strictly related to the opportunity to enter in working

Plasmonic non-concentric nanorings array as an unidirectional nano-optical conveyor belt actuated by polarization rotation.

Science.gov (United States)

Jiang, Min; Wang, Guanghui; Jiao, Wenxiang; Ying, Zhoufeng; Zou, Ningmu; Ho, Ho-Pui; Sun, Tianyu; Zhang, Xuping

2017-01-15

We report a nano-optical conveyor belt containing an array of gold plasmonic non-concentric nanorings (PNNRs) for the realization of trapping and unidirectional transportation of nanoparticles through rotating the polarization of an excitation beam. The location of hot spots within an asymmetric plasmonic nanostructure is polarization dependent, thus making it possible to manipulate a trapped target by rotating the incident polarization state. In the case of PNNR, the two poles have highly unbalanced trap potential. This greatly enhances the chance of transferring trapped particles between adjacent PNNRs in a given direction through rotating the polarization. As confirmed by three-dimensional finite-difference time-domain analysis, an array of PNNRs forms an unidirectional nano-optical conveyor belt, which delivers target nanoparticles or biomolecules over a long distance with nanometer accuracy. With the capacity to trap and to transfer, our design offers a versatile scheme for conducting mechanical sample manipulation in many on-chip optofluidic applications.

Two-dimensional mathematical model for simulation of the drying process of thick layers of natural materials in a conveyor-belt dryer

Directory of Open Access Journals (Sweden)

Salemović Duško R.

2017-01-01

Full Text Available This paper presents the mathematical model and numerical analysis of the convective drying process of thick slices of colloidal capillary-porous materials slowly moving through conveyor-belt dryer. A flow of hot moist air was used as drying agent. The drying process has been analyzed in the form of a 2-D mathematical model, in two directions: along the conveyor and perpendicular on it. The mathematical model consists of two non-linear differential equations and one equation with a transcendent character and it is based on the mathematical model developed for drying process in a form of a 1-D thin layer. The appropriate boundary conditions were introduced. The presented model is suitable for the automated control of conveyor-belt dryers. The obtained results with analysis could be useful in predicting the drying kinetics of potato slices and similar natural products.

Analysis of the influence of design parameters of vertically-closed track conveyor with suspended belt and distributed drive on the technical specifications

Directory of Open Access Journals (Sweden)

Tolkachev E.N.

2016-12-01

Full Text Available Using the basic design of the conveyor with suspended belt and distributed drive, a series of numerical calcu-lations was performed. As a result, the influence of design parameters of vertical loop route on the main tech-nical parameters of the conveyor was established. Recommendations on the choice of rational parameters were formulated.

On-line determination of moisture in coke on conveyor belts

International Nuclear Information System (INIS)

Millen, M.J.; Rafter, P.T.; Sowerby, B.D.

1988-01-01

A fast neutron and γ-ray transmission technique is being developed for the on-line determination of moisture in coke on conveyor belts. Calculations show that the technique is capable of determining coke moisture to within 0.3 wt% for coke thicknesses down to 50 mm provided that count rates are measured to within 0.1% relative. Laboratory measurements on static and moving coke samples showed that coke moisture can be determined to within 0.25 and 0.45 wt% for crushed and lump coke, respectively. It is planned to carry out a long-term plant trial of the technique on lump coke feed to the No. 3 blast furnace at BHP, Newcastle, NSW, Australia. (author)

Mules needed to install belt conveyor. Beumer executes major order in China

Energy Technology Data Exchange (ETDEWEB)

Anon.

2008-07-01

Asia Cement Group, a major building material manufacturer headquartered in Taipeh (Taiwan), has built a new plant in the vicinity of Chengdu, the capital of Sichuan. Currently, a kiln with a capacity of 4200 tons per day is installed there. For moving the limestone from the quarry to the factory, located 30 km away, the Asia Cement Group has commissioned BEUMER with constructing a curved belt conveyor. The major order with a total volume of EUR 5 million includes design and installation of a 12.5-kilometre long system through rough mountainous terrain. (orig.)

On the transversal vibrations of a conveyor belt with a low and time-varying velocity : Part I: the string-like case

NARCIS (Netherlands)

Suweken, G.; Van Horssen, W.T.

2001-01-01

In this paper initial-boundary value problems for a linear wave (string) equation are considered. These problems can be used as simple models to describe the vertical vibrations of a conveyor belt, for which the velocity is small with respect to the wave speed. In this paper the belt is assumed to

Detection of the strange bodies on the conveyor belt using gamma radiation technique

International Nuclear Information System (INIS)

Barna, A.; Ochiana, G.; Oncescu, M.

1990-01-01

The aim of this paper is to present a method for the computation of the activity of a gamma radiation source used in a radiometric assembly designed to detect the strange bodies (iron, stone or wood-made granules) within the textile material on the conveyor belt. The mathematical modelling method based on the Monte Carlo procedure has been used, with different values of the errors of types I and II; the investigation method is the transmission of gamma radiations. (Author)

Investigating possible use of roller bearings made of plastic in belt conveyor idlers

Energy Technology Data Exchange (ETDEWEB)

Grzeszek, A

1979-05-01

This paper presents results of laboratory and operational tests of roller bearings made of polyamide in belt conveyor idlers. During operational tests the conveyor was inclined to one side so the load on individual bearings varied and the bearings were also covered with dust and dirt. The tests show that the first failures of the plastic bearings took place after 3 months but some of the bearings were in operation one year without failures. All the failures were caused by wear of the bearing due to dust and dirt on their sliding surface. Increased friction resulted in higher temperatures which deformed the bearings. The tests showed that the bearings which were not dirty operated without failure. It is concluded that the plastic-made roller bearings cannot be used under conditions of brown coal surface mines as these mines are characterized by intense dustfall and by dirt which would increase friction in the bearings. (In Polish)

Belt conveying of minerals

Energy Technology Data Exchange (ETDEWEB)

Stace, L.R.; Yardley, E.D. [University of Nottingham, Nottingham (United Kingdom). School of Civil Engineering

2008-02-15

A discussion of the history and economics of conveyor applications sets the scene. Conveyor design is investigated in detail, covering power requirements, belt tensioning, and hardware. Principles regarding construction and joining of belts are outlined and a helpful and practical overview of relevant standards, belt test methods, and issues surrounding standardisation is given. Conveyor belt systems can represent a significant operational hazard, so the authors have set out to highlight the important area of safety, with consideration given to fire/electrical resistance, as well as the interface between personnel and conveyor systems - including nip points and operational issues such as man-riding. Selected case studies illustrate some practical aspects of installation and operation, at Selby mine in the UK and Prosper-Haniel Colliery in Germany and others. 3 apps.

Noise Reduction of Steel Cord Conveyor Belt Defect Electromagnetic Signal by Combined Use of Improved Wavelet and EMD

Directory of Open Access Journals (Sweden)

Hong-Wei Ma

2016-09-01

Full Text Available In order to reduce the noise of a defect electromagnetic signal of the steel cord conveyor belt used in coal mines, a new signal noise reduction method by combined use of the improved threshold wavelet and Empirical Mode Decomposition (EMD is proposed. Firstly, the denoising method based on the improved threshold wavelet is applied to reduce the noise of a defect electromagnetic signal obtained by an electromagnetic testing system. Then, the EMD is used to decompose the denoised signal and then the effective Intrinsic Mode Function (IMF is extracted by the dominant eigenvalue strategy. Finally, the signal reconstruction is carried out by utilizing the obtained IMF. In order to verify the proposed noise reduction method, the experiments are carried out in two cases including the defective joint and steel wire rope break. The experimental results show that the proposed method in this paper obtains the higher Signal to Noise Ratio (SNR for the defect electromagnetic signal noise reduction of steel cord conveyor belts.

Stagnation, circulation, and erosion of granular materials through belt conveyor sluice gate

Science.gov (United States)

Pohlman, Nicholas; Moralda, Michael; Dunne, Ryan

2013-11-01

Control of flow rates in conversion reactors for discrete materials like biomass can be achieved in belt conveyors through a combination of belt speed, hopper size, and aperture opening. As material is extracted from the bottom of the storage hopper, other material cannot achieve plug flow and therefore is restricted from exiting through a sluice-gate type opening. The excess material moves vertically from the opening causing a pile up and recirculation back along the free surface of the hopper. Experimental results obtained through high speed imaging show the position of the stagnation point as well as the rate of circulation is dependent on the mass flow rate achieved and instantaneous fill level. The movement of material into the plug flow along the belt allows verification of deposition models on erodible beds rather than rigid surfaces with artificial roughness of glued particles. Similarly, the pile-up at the exit influences the efficiency of the transport affecting the narrow energy return on investment of biomass resources. The laboratory-scale behavior can therefore be translated into industrial performance metrics for increased operational efficiency. This work is supported by the NSF REU Site Operation E-Tank under award number 1156789.

Scintillation densimeter for liquids and an isotopic conveyor weighers with plastic scintillator

International Nuclear Information System (INIS)

Makhaj, B.; Antonyak, V.; Plyater, Z.

1979-01-01

The method is described of the weighted material's mass measuring according to the results of the conveyor momentary load measurement derived from the attenuation of radiation in the transmission geometry, conveyor belt velocity measurement and digital processing of the signals from the measurement of the bouth values. In the measuring gage there are located: the point type gamma source of cesium-137 with 4 mCi capacity, the scintillation detector with plastic cylindric scintillator of 5 cm in diameter and with the length approximately equal to the width of the conveyor belt and also the tachometer-generator. The conveyor weighers described is intended for use with conveyor having belt; from 60 to 180 cm wide. The results are given of industrial exploitation of the instrument [ru

The use of tubular belt conveyors for the industrial waste of enterprises

Directory of Open Access Journals (Sweden)

S. Ya. Davydov

2017-12-01

Full Text Available The methods of processing slag of electrolyzers and reverberatory furnaces slag of secondary aluminum production, obtained after extracting aluminum, as well as ash and slag of thermal power plants, hydro plants, waste of ferrous metallurgy in the construction industry are presented in this work. Tubular belt conveyor (TBC with the use of special expensive tapes, are widely used abroad for moving industrial raw materials. It is also used in Russia (Lebedinsky ore-dressing and processing enterprise and Reftinskaya hydro power. A tape which is rolled in a tube allows to improve the sanitary conditions of labor, to ensure the full safety of cargo, to exclude the harmful effects of aggressive chemical cargoes at the metal of the conveyor, extending its service life. There is an opportunity to convey materials under the angle of 20–25°. The main drawback of TBC, which exist today, is that they are working on an especially patented tape, which is very expensive and it is not produced in Russia. The costs of its replacement are comparable to the price of the pipeline. The Russian customers have already faced this problem. The components are not produced in Russia either, and the cost of their subsequent purchases increases dramatically. The technical parameters of TBC of the Lebedinsky ore-dressing and processing enterprise and the Reftinskaya hydro power, as well as a comparative table on the use of TBC are presented in this work. Lists of the advantages of TBC are also adduced. The characteristic of TBC Contitech are given. The use of modern anti-static and flame retardant polymeric materials in the manufacture of the rollers will allow further progress in solving the issues of safe operation of belt conveyors. Such important parameters as reliability and maintainability were taken into account while constructing these conveyors. The tests to replace the metal clips with the rollers, which are made of anti-static polymers are carried out. This

Investigations dealing with variable-speed drives of belt conveyor systems; Untersuchungen an drehzahlstellbaren Antrieben von Gurtbandfoerderanlagen

Energy Technology Data Exchange (ETDEWEB)

Heuvel, B. van den [RWE Power AG, Technikzentrum Tagebaue/Hauptwerkstatt, Versuchsabteilung, Frechen (Germany)

2006-04-15

Safe and faultless operation of belt conveyor systems is a crucial factor in maintaining the availability of interlinked conveying systems employed in mining operations; the use of components with a high efficiency or low energy consumption and energy-conserving plant operation modes allow economic efficiency to be enhanced. With the power increase of single drives to 2500 kW the static design is gaining significance and - with the introduction of variable-speed conveyor drives - particular importance is also to be attached to the proper dynamic design and adjustment of the drive units. Comprehensive measurement and computational studies made of different conveyor drive units in the 900 to 2500 kW power range revealed that excitations of torsional natural frequencies caused by the drives' tooth contact frequencies were the reason for the damage that had occurred; remedial measures were developed the efficacy of which was demonstrated in practice. Moreover, investigations aimed at precautionary damage prevention are described which were performed with newly designed gears prior to the conversion of proven conveyor drives to variable-speed drive units. When designing new gears in the future, we recommend to also investigate them with regard to their dynamic behaviour in the drive train during the design phase by performing appropriate torsional vibration analyses. (orig.)

Radioisotope conveyor ash meter

International Nuclear Information System (INIS)

Savelov, V.D.

1994-01-01

Radioisotope conveyor ash meter realizes persistent measuring of ashiness of coal and products of its enrichment on the belt conveyor without contact. The principle of ash meter acting is based on functional dependence of the gamma radiation flows backscattering intensity of radioisotope sources from the ash volume content in the controlled fuel. Facility consists from the ashiness transducer and the processing and control device

Microfluidic magnetic bead conveyor belt.

Science.gov (United States)

van Pelt, Stijn; Frijns, Arjan; den Toonder, Jaap

2017-11-07

Magnetic beads play an important role in the miniaturization of clinical diagnostics systems. In lab-on-chip platforms, beads can be made to link to a target species and can then be used for the manipulation and detection of this species. Current bead actuation systems utilize complex on-chip coil systems that offer low field strengths and little versatility. We demonstrate a novel system based on an external rotating magnetic field and on-chip soft-magnetic structures to focus the field locally. These structures were designed and optimized using finite element simulations in order to create a number of local flux density maxima. These maxima, to which the magnetic beads are attracted, move over the chip surface in a continuous way together with the rotation of the external field, resulting in a mechanism similar to that of a conveyor belt. A prototype was fabricated using PDMS molding techniques mixed with iron powder for the magnetic structures. In the subsequent experiments, a quadrupole electromagnet was used to create the rotating external field. We observed that beads formed agglomerates that rolled over the chip surface, just above the magnetic structures. Field rotation frequencies between 0.1-50 Hz were tested resulting in magnetic bead speeds of over 1 mm s -1 for the highest frequency. With this, we have shown that our novel concept works, combining a simple design and simple operation with a powerful and versatile method for bead actuation. This makes it a promising method for further research and utilization in lab-on-chip systems.

ANALYSIS OF MOVEMENT RESISTANCE OF CONVEYOR BELT AND ROLLERS IN THE COAL MINE MYSŁOWICE-WESOŁA

Directory of Open Access Journals (Sweden)

Tadeusz OPASIAK

2014-03-01

Full Text Available The paper presents a study of new design of SAG rollers. The study focused on the measurement of static and dynamic resistance of rotating rollers and the impact of new construction on the power consumption of the conveyor. Rollers have been modified through the use of class C4 bearing seals and labyrinth seal U4Exp 62/65 with a cover 2LU4 of runner construction. Measurements of static and dynamic resistance of rotating rollers were made on a universal rollers test bench, and power measurements were carried out on a belt conveyor power supply system Gwarek 1200 No. TW in KWK Mysłowice-Wesoła

Research on the Influence of Weighing Accuracy Caused by the Position of Tension Wheel on the Electronic Belt-Conveyor Scale

Science.gov (United States)

Zhang, Kun; Zhang, Hu; Song, Qiuzhi

2018-01-01

In this paper, a Single- Idler electronic belt-conveyor scale is the Object of study. The contact force between the belt and the supporting roller is calculated by the finite element analysis software ABAQUS. The relationship between the tension distance of the tension wheel and the contact force between the belt and the weighing roller is obtained. The best stretching distance is found through analysis. And the conclusion which is the weighing error is different at the same stretching distance but the different weight of material is obtained. A compensation mechanism is proposed to improve the weighing accuracy.

design and implementation of conveyor line speed synchroniser

African Journals Online (AJOL)

user

2016-07-03

Jul 3, 2016 ... This paper presents the mathematical modeling of a conveyor ... speed of action of other process machines results in ..... 3.1 Simulation Results of Dc Motor and Belt Conveyor .... Using MATLAB, SIMULINK, and Control.

Field trial of a pair production gauge for the on-line determination of ash in coal on a conveyor belt

International Nuclear Information System (INIS)

Millen, M.J.; Sowerby, B.D.; Rafter, P.T.; Ellis, W.K.; Gravitis, V.L.; Howells, E.; McLennan, T.D.; Muldoon, L.J.

1984-01-01

The ash content of coal can be determined by a method based on pair production. Coal is irradiated with high energy γ-rays and the resulting 0.511 MeV annihilation and Compton scattered γ-rays are measured. The pair production (PP) technique has been previously proved in the laboratory on static bulk samples and in the field on high-throughput sample by-lines. In the present paper, a plant test to assess the PP gauge for direct on-line conveyor belt analysis is described. This test was undertaken on the recirculating coal facility at the pilot plant coal washery at the BHP Steel Works, Newcastle, New South Wales. Seven Hunter Valley coals with ash in the range 7.5-33 wt% were circulated around the conveyor loop, and scanned by both PP and low energy γ-ray transmission (LET) gauges. Samples were measured on-belt as a function of sample depth, compaction, moisture and particle size. The mass per unit area of coal on the belt was varied in the range 40-210 kg m -2 . The r.m.s. deviation between PP gauge ash and chemical laboratory ash was 1.07 wt% ash for 370 individual on-belt measurements on coal of mass per unit area greater than 60 kg m -2 ad 0.45 wt% ash for the mean ash of each sample. (author)

High tech conveyors unitize Selby coal

Energy Technology Data Exchange (ETDEWEB)

1985-10-01

Designs proposed by Anderson Strathclyde PLC and Cable Belt for single-flight conveyors to bring the output of the five Selby mines to the surface have both been developed by the UK National Coal Board. Both designs extend the limits of conveyor technology and are expected to economise on transport and longwalling costs. 4 references.

Coal belt options

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-03-15

Whether moving coal long distances overland or short distances in-plant, belt conveyors will always be in demand. The article reports on recent systems developments and applications by Beumer, Horizon Conveyor Equipment, Conveyor Dynamics, Doppelmayr Transport Technology, Enclosed Bulk Systems, ContiTech and Bateman Engineered Technologies. 2 photos.

Study on the reliability of the underground conveyor belt system installed at Vulcan Mine, the Jiu Valley Basin in Romania

Directory of Open Access Journals (Sweden)

Tomuș Ovidiu-Bogdan

2017-01-01

Full Text Available The paper deals with a comprehensive reliability analysis of the conveyor belts belonging to an underground coal mine in the Jiu Valley, Romania. As resulted from the mine management reports, the transportation system is responsible for many downtimes and is a real bottleneck in the constant and adequate production, and the suspicion is the weak state of belt conveyers, which are the spinal column of the extraction process. For this reason, a comprehensive reliability analysis has been decided, in order to deliver a maintenance-upgrading plan.

The chloroplast thylakoid membrane system is a molecular conveyor belt.

Science.gov (United States)

Critchley, C

1988-10-01

Light drives photosynthesis, but paradoxically light is also the most variable environmental factor influencing photosynthesis both qualitatively and quantitatively. The photosynthetic apparatus of higher plants is adaptable in the extreme, as exemplified by its capacity for acclimation to very bright sunny or deeply shaded conditions. It can also respond to rapid changes in light such as sunflecks. In this paper I offer a model that i) explains the thylakoid membrane organisation into grana stacks and stroma lamellae, ii) proposes a role for rapid D1 protein turnover and LHCII phosphorylation, and iii) suggests a mechanism for photoinhibition. I argue that the photosynthetic membrane system is dynamic in three dimensions, so much so that, in the light, it is in constant motion and operates in a manner somewhat analogous to a conveyor belt. D1 protein degradation is proposed to be the motor that drives this system. Photoinhibition is suggested to be due to the arrest of D1 protein turnover.

Mode-based microparticle conveyor belt in air-filled hollow-core photonic crystal fiber.

Science.gov (United States)

Schmidt, Oliver A; Euser, Tijmen G; Russell, Philip St J

2013-12-02

We show how microparticles can be moved over long distances and precisely positioned in a low-loss air-filled hollow-core photonic crystal fiber using a coherent superposition of two co-propagating spatial modes, balanced by a backward-propagating fundamental mode. This creates a series of trapping positions spaced by half the beat-length between the forward-propagating modes (typically a fraction of a millimeter). The system allows a trapped microparticle to be moved along the fiber by continuously tuning the relative phase between the two forward-propagating modes. This mode-based optical conveyor belt combines long-range transport of microparticles with a positional accuracy of 1 µm. The technique also has potential uses in waveguide-based optofluidic systems.

Primary investigation of a design for a dual energy gamma-ray transmission gauge to determine the ash content of coal on a conveyor belt

International Nuclear Information System (INIS)

Abedinzadeh, A.; Rahimi, H.; Rahimi, N.; Amini, A.; Naimpour, A.; Moafian, J.

1993-01-01

In order to design a dual energy γ-ray transmission gauge for measuring, on-line, the ash content of coal, an investigation was carried out to determine the relation between the theoretical mass absorption coefficient (μ-bar) and the % ash of coal in the Kerman District Coal Mines. Because coal, transported on a conveyor belt, may be a non-homogeneous mixture from one or more mines, it was decided to compare % ash in a mixture of coals from several mines with that from individual mines, the measurements being made whilst the coal was being transported on a conveyor belt. The investigation shows that the relation between the mass absorption coefficient and the % ash in a coal mixture from several mines cannot be used to assess, accurately, the value of μ-bar for coals from individual mines in this particular region. (author)

Enclosed belts in the ascendancy

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-03-15

Although there will always be a place for traditional overland belt conveyors, enclosed belt systems are increasingly being specified where environmental protection assumes high priority or where there is a need to protect material from the weather. The article reports on recent conveyor projects such as: an MRC cable Belt in a 6.4 km system to carry coal in the Appalachian Mountains; a $40 m contract awarded to FL Smidth to supply an integrated coal handling system to LILIAMA in Vietnam and other contracts to handle coal for India's Coastal Gujarat Power; and a contract awarded to Bateman Engineered Technologies to supply a 7 km Japan Pipe Conveyor for a coal power station in Brazil. 3 photos.

Analysis of the influence of the cutting edge geometry on parameters of the perforation process for conveyor and transmission belts

Directory of Open Access Journals (Sweden)

Wojtkowiak Dominik

2018-01-01

Full Text Available Perforated belts, which are used in vacuum conveyor belts, can have significantly different mechanical properties like strength and elasticity due to a variety of used materials and can have different thickness from very thin (0,7 mm to thick belts (6 mm. In order to design a complex machine for mechanical perforation, which can perforate whole range of belts, it is necessary to research the influence of the cutting edge geometry on the parameters of the perforation process. Three most important parameters, which describe the perforation process are the cutting force, the velocity and the temperature of the piercing punch. The results presented in this paper consider two different types of punching (a piercing punch with the punching die or with the reducer plate and different cutting edge directions, angles, diameters and material properties. Test were made for different groups of composites belts – with polyurethane and polyester fabric, polyamide core or aramid-fibre reinforced polymers. The main goal of this research is to specify effective tools and parameters of the perforation process for each group of composites belts.

Harmonisation of fire testing of conveyor belts for underground applications within the EC; Harmonisierung der brandtechnischen Pruefverfahren von Foerdergurten fuer den Einsatz unter Tage innerhalb der EG

Energy Technology Data Exchange (ETDEWEB)

Foit, W. [DMT-Gesellschaft fuer Forschung und Pruefung mbH, Dortmund (Germany). Fachstelle fuer Brand- und Explosionsschutz unter Tage - Versuchsgrube Tremonia

1998-12-01

The mining countries of the EC still have different regulations for fire testing of conveyor belts. The test methods will be harmonized for the Common Market, and requirements on conveyor belts will be standardized within the EC. A new EC standard will be drawn up. [Deutsch] Zur Zeit sind in den bergbaubetreibenden Laendern der EG noch unterschiedliche Verfahren zur brandtechnischen Pruefung von Foerdergurten vorgeschrieben. Mit dem Inkrafttreten des Gemeinsamen Marktes und der damit zusammenhaengenden Forderung nach Abbau von Handelshemmnissen sollen diese Pruefverfahren harmonisiert werden. Ziel ist es, die an die Foerdergurte zu stellenden brandtechnischen Anforderungen innerhalb der EG zu vereinheitlichen. Es soll deshalb eine europaeische Norm zur Beurteilung des Brandverhaltens und der Brandausbreitung an Foerdergurten fuer den Kohlenbergbau unter Tage erstellt werden. (orig./MSK)

Release measurement of great amount of waste. Conveyor belt versus wire mesh pallet systems

Energy Technology Data Exchange (ETDEWEB)

Sokcic-Kostic, Marina; Schultheis, Roland; Langer, Felix [NUKEM Technologies Engineering Services GmbH, Alzenau (Germany)

2014-08-15

Great amount of waste has to be measured for release during the decommissioning and rebuilding of nuclear facilities and installation. Since the enclosed storage or decontamination is very expensive it is advisable for economic reasons to separate contaminated material. The necessary measurement is however a time and cost intensive work which has carefully provided. There are two general methods to perform this task: one is a continuously running system on the basis of a conveyor belt system. The other approach is a discontinuously running system using wire mesh pallets. With the knowledge from existing installations this article will discuss the pro's and contra's and show the limits of the systems.

3-D visualization of ensemble weather forecasts - Part 2: Forecasting warm conveyor belt situations for aircraft-based field campaigns

Science.gov (United States)

Rautenhaus, M.; Grams, C. M.; Schäfler, A.; Westermann, R.

2015-02-01

We present the application of interactive 3-D visualization of ensemble weather predictions to forecasting warm conveyor belt situations during aircraft-based atmospheric research campaigns. Motivated by forecast requirements of the T-NAWDEX-Falcon 2012 campaign, a method to predict 3-D probabilities of the spatial occurrence of warm conveyor belts has been developed. Probabilities are derived from Lagrangian particle trajectories computed on the forecast wind fields of the ECMWF ensemble prediction system. Integration of the method into the 3-D ensemble visualization tool Met.3D, introduced in the first part of this study, facilitates interactive visualization of WCB features and derived probabilities in the context of the ECMWF ensemble forecast. We investigate the sensitivity of the method with respect to trajectory seeding and forecast wind field resolution. Furthermore, we propose a visual analysis method to quantitatively analyse the contribution of ensemble members to a probability region and, thus, to assist the forecaster in interpreting the obtained probabilities. A case study, revisiting a forecast case from T-NAWDEX-Falcon, illustrates the practical application of Met.3D and demonstrates the use of 3-D and uncertainty visualization for weather forecasting and for planning flight routes in the medium forecast range (three to seven days before take-off).

Modelling and control system of multi motor conveyor

Science.gov (United States)

Kovalchuk, M. S.; Baburin, S. V.

2018-03-01

The paper deals with the actual problem of developing the mathematical model of electromechanical system: conveyor – multimotor electric drive with a frequency converter, with the implementation in Simulink/MatLab, which allows one to perform studies of conveyor operation modes, taking into account the specifics of the mechanism with different electric drives control algorithms. The authors designed the mathematical models of the conveyor and its control system that provides increased uniformity of load distribution between drive motors and restriction of dynamic loads on the belt (over-regulation until 15%).

Conveyor technology rolls ahead to keep pace with industry demands

Energy Technology Data Exchange (ETDEWEB)

Fiscor, S.

2007-11-15

New drives, belts and rolling components maintain capacity but require less energy and maintenance. Computer-assisted component design and system modelling are becoming standard in improving conveyors for transporting ores, pellets or coal in open-cast mines. Continental Conveyor, for example, uses Statix modelling software to analyze existing conveyor systems and design new ones. Sandvik Materials Handling uses discrete element modelling. Developments by the major manufacturers including Veyance Technologies, Hagglunds Drives, and TPKL complings in drives, complings, conveyors, monitoring systems etc. are described in this article. 2 photos.

Substantiation of selection method of preferred alternative of belt conveyor drive systems on the basis of the analytic hierarchy process

Directory of Open Access Journals (Sweden)

Goncharov K.A.

2016-06-01

Full Text Available This paper provides substantiation of selection method of preferred alternative of belt conveyor drive systems on the basis of the analytic hierarchy process. Conditions for the correct application of the proposed method in the selection process of preferred alternative of technical objects were worked out. The set of criteria of system effectiveness evalua-tion and the corresponding hierarchical structure in accordance with the developed conditions was proposed.

Three-dimensional visualization of ensemble weather forecasts - Part 2: Forecasting warm conveyor belt situations for aircraft-based field campaigns

Science.gov (United States)

Rautenhaus, M.; Grams, C. M.; Schäfler, A.; Westermann, R.

2015-07-01

We present the application of interactive three-dimensional (3-D) visualization of ensemble weather predictions to forecasting warm conveyor belt situations during aircraft-based atmospheric research campaigns. Motivated by forecast requirements of the T-NAWDEX-Falcon 2012 (THORPEX - North Atlantic Waveguide and Downstream Impact Experiment) campaign, a method to predict 3-D probabilities of the spatial occurrence of warm conveyor belts (WCBs) has been developed. Probabilities are derived from Lagrangian particle trajectories computed on the forecast wind fields of the European Centre for Medium Range Weather Forecasts (ECMWF) ensemble prediction system. Integration of the method into the 3-D ensemble visualization tool Met.3D, introduced in the first part of this study, facilitates interactive visualization of WCB features and derived probabilities in the context of the ECMWF ensemble forecast. We investigate the sensitivity of the method with respect to trajectory seeding and grid spacing of the forecast wind field. Furthermore, we propose a visual analysis method to quantitatively analyse the contribution of ensemble members to a probability region and, thus, to assist the forecaster in interpreting the obtained probabilities. A case study, revisiting a forecast case from T-NAWDEX-Falcon, illustrates the practical application of Met.3D and demonstrates the use of 3-D and uncertainty visualization for weather forecasting and for planning flight routes in the medium forecast range (3 to 7 days before take-off).

Energy calculation model of an outgoing conveyor with application of a transfer chute with the damping plate

OpenAIRE

V. Molnár; G. Fedorko; N. Husáková; J. Král' Jr.; M. Ferdynus

2016-01-01

The energy efficiency of transport systems consisting of several belt conveyors is significantly affected by re-direction. The proper sizing of several conveyor belts using deflector plates can significantly affect their efficiency. At present, there are no uniform rules (models) which specify the methodology and procedures for their design. This paper brings proposals of design of optimal parameters for energy-efficient operation of the transport system consisting of belt ...

Transient Torsional Analysis of a Belt Conveyor Drive with Pneumatic Flexible Shaft Coupling

Directory of Open Access Journals (Sweden)

Kaššay Peter

2017-03-01

Full Text Available Development and application of pneumatic flexible shaft couplings have been in the center of our department research activities for a long time. These couplings are able to change torsional stiffness by changing pressure in their flexible elements – air bellows. Until now we have dealt with the use of pneumatic flexible shaft couplings for tuning mechanical systems working with periodically alternating load torque at steady state. Some mechanical systems, however, operate with a static load torque at constant speed (e.g. hoists, elevators, etc., where it is necessary to consider the suitability of shaft coupling in terms of load torque at transient conditions (run-up and braking. Therefore we decided to analyze the use of pneumatic flexible shaft couplings also in this type of mechanical systems on an example of conveyor belt drive.

A conveyor belt task for assessing visuo-motor coordination in the marmoset (Callithrix jacchus): effects of diazepam, chlorpromazine, pentobarbital and d-amphetamine.

Science.gov (United States)

D'Mello, G D; Duffy, E A; Miles, S S

1985-01-01

A conveyor belt task for assessing visuo-motor coordination in the marmoset is described. Animals are motivated by apple, a preferred food, under a state of minimal food deprivation. The apparatus used was designed to test animals within their home cages and not restrained in any way, thus avoiding possible confounding factors associated with restraint stress. Stable baseline levels of performance were reached by all animals in a median of 24 sessions. Performance was shown to be differentially sensitive to the effects of four psychoactive drugs. Moderate doses of diazepam, chlorpromazine and pentobarbital disrupted visuo-motor coordination in a dose-related manner. The possibility that disruption of performance observed at higher doses may have resulted from non-specific actions of these drugs such as decreases in feeding motivation were not supported by results from ancillary experiments. Changes in performance characteristic of high dose effects were similar in nature to changes observed when the degree of task difficulty was increased. Doses of d-amphetamine up to and including those reported to produce signs of stereotypy failed to influence performance. The potential of the conveyor belt task for measuring visuo-motor coordination in both primate and rodent species is discussed.

The Baltic haline conveyor belt or the overturning circulation and mixing in the Baltic.

Science.gov (United States)

Döös, Kristofer; Meier, H E Markus; Döscher, Ralf

2004-06-01

A study of the water-mass circulation of the Baltic has been undertaken by making use of a three dimensional Baltic Sea model simulation. The saline water from the North Atlantic is traced through the Danish Sounds into the Baltic where it upwells and mixes with the fresh water inflow from the rivers forming a Baltic haline conveyor belt. The mixing of the saline water from the Great Belt and Oresund with the fresh water is investigated making use of overturning stream functions and Lagrangian trajectories. The overturning stream function was calculated as a function of four different vertical coordinates (depth, salinity, temperature and density) in order to understand the path of the water and where it upwells and mixes. Evidence of a fictive depth overturning cell similar to the Deacon Cell in the Southern Ocean was found in the Baltic proper corresponding to the gyre circulation around Gotland, which vanishes when the overturning stream function is projected on density layers. A Lagrangian trajectory study was performed to obtain a better view of the circulation and mixing of the saline and fresh waters. The residence time of the water masses in the Baltic is calculated to be 26-29 years and the Lagrangian dispersion reaches basin saturation after 5 years.

Studies of The Durability of Belt Conveyor Idlers with Working Loads Taken into Account

Science.gov (United States)

Król, Robert

2017-12-01

The results of laboratory and operational studies conducted in the Machinery Systems Division of Wroclaw University of Technology in recent years have became the basis for selecting proper belt conveyor roller designs optimized for specific strength and operational criteria. The usefulness of the results for assessing the energy intensity of idlers, estimating their durability and determining modernization policies has been confirmed. Methods of estimating the durability of carrying idlers on the basis of the identified output stream distributions are presented. Results of studies carried out using an analytical method and a laboratory method are reported. It has been shown that the operational durability of a roller is determined by its design, the roller set parameters (the spacing and the angle of bevel) and the operating conditions having a bearing on the irregularity of the transported output stream.

30 CFR 75.1728 - Power-driven pulleys.

Science.gov (United States)

2010-07-01

... hands except on slow-moving equipment especially designed for hand feeding. (b) Pulleys of conveyors shall not be cleaned manually while the conveyor is in motion. (c) Coal spilled beneath belt conveyor... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Miscellaneous § 75.1728 Power-driven pulleys. (a) Belts...

Belt Aligning Revisited

Directory of Open Access Journals (Sweden)

Yurchenko Vadim

2017-01-01

parts of the conveyor, the sides of the belt wear intensively. This results in reducing the life of the belt. The reasons for this phenomenon are well investigated, but the difficulty lies in the fact that they all act simultaneously. The belt misalignment prevention can be carried out in two ways: by minimizing the effect of causes and by aligning the belt. The construction of aligning devices and errors encountered in practice are considered in this paper. Self-aligning roller supports rotational in plan view are recommended as a means of combating the belt misalignment.

Large belt conveyors: starting them and keeping them going

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-03-15

Although heavy-duty conveyor drives are subjected to some of the most severe operating conditions, it is still possible to achieve reliability and low maintenance. Some areas where choices in design and construction can make a difference include thermal capacity, sealing, lubrication and strength. Dodge recently brought out its redesigned Global Series 750 CST - controlled start transmission - a multi-stage gear reducer with an internal clutch designed for smooth starting of high inertia loads on long-distance conveyors. The Antelope Mine in Wyoming's Powder River Basin first installed Dodge CST units in 1984 and has added more units over the years. CSTs have also been successfully employed in Australian coal mines. 1 fig., 1 photo.

Evaluation of common cleaning and disinfection programmes in battery cage and on-floor layer houses in France.

Science.gov (United States)

Huneau-Salaün, A; Michel, V; Balaine, L; Petetin, I; Eono, F; Ecobichon, F; Bouquin, S Le

2010-04-01

1. The aim in this study was to evaluate cleaning and disinfection programmes in battery cage and on-floor layer houses in France. 2. Cleaning and disinfection efficiency was assessed by a visual evaluation of cleaning and a bacteriological monitoring of surface contamination from counts of thermotolerant streptococci on contact agar plates. 3. In battery cage houses, dropping belts, manure conveyors, and house floors remained highly contaminated due to poor cleaning in half of the buildings examined. 4. In on-floor houses, a high standard of cleaning was achieved but errors in the planning of cleaning and disinfection operations sometimes led to a high residual contamination of nest boxes and egg sorting tables.

Conveyor belt effect in the flow through a tube of a viscous fluid with spinning particles.

Science.gov (United States)

Felderhof, B U

2012-04-28

The extended Navier-Stokes equations describing the steady-state hydrodynamics of a viscous fluid with spinning particles are solved for flow through a circular cylindrical tube. The flow caused by an applied torque density in the azimuthal direction and linear in the radial distance from the axis is compared with the flow caused by a uniform applied force density directed along the axis of the tube. In both cases the flow velocity is of Poiseuille type plus a correction. In the first case the flow velocity is caused by the conveyor belt effect of spinning particles. The corrections to the Poiseuille flow pattern in the two cases differ only by a proportionality factor. The spin velocity profiles in the two cases are also proportional.

Three-dimensional visualization of ensemble weather forecasts – Part 2: Forecasting warm conveyor belt situations for aircraft-based field campaigns

Directory of Open Access Journals (Sweden)

M. Rautenhaus

2015-07-01

Full Text Available We present the application of interactive three-dimensional (3-D visualization of ensemble weather predictions to forecasting warm conveyor belt situations during aircraft-based atmospheric research campaigns. Motivated by forecast requirements of the T-NAWDEX-Falcon 2012 (THORPEX – North Atlantic Waveguide and Downstream Impact Experiment campaign, a method to predict 3-D probabilities of the spatial occurrence of warm conveyor belts (WCBs has been developed. Probabilities are derived from Lagrangian particle trajectories computed on the forecast wind fields of the European Centre for Medium Range Weather Forecasts (ECMWF ensemble prediction system. Integration of the method into the 3-D ensemble visualization tool Met.3D, introduced in the first part of this study, facilitates interactive visualization of WCB features and derived probabilities in the context of the ECMWF ensemble forecast. We investigate the sensitivity of the method with respect to trajectory seeding and grid spacing of the forecast wind field. Furthermore, we propose a visual analysis method to quantitatively analyse the contribution of ensemble members to a probability region and, thus, to assist the forecaster in interpreting the obtained probabilities. A case study, revisiting a forecast case from T-NAWDEX-Falcon, illustrates the practical application of Met.3D and demonstrates the use of 3-D and uncertainty visualization for weather forecasting and for planning flight routes in the medium forecast range (3 to 7 days before take-off.

Combined steam-ultrasound treatment of 2 seconds achieves significant high aerobic count and Enterobacteriaceae reduction on naturally contaminated food boxes, crates, conveyor belts, and meat knives.

Science.gov (United States)

Musavian, Hanieh S; Butt, Tariq M; Larsen, Annette Baltzer; Krebs, Niels

2015-02-01

Food contact surfaces require rigorous sanitation procedures for decontamination, although these methods very often fail to efficiently clean and disinfect surfaces that are visibly contaminated with food residues and possible biofilms. In this study, the results of a short treatment (1 to 2 s) of combined steam (95°C) and ultrasound (SonoSteam) of industrial fish and meat transportation boxes and live-chicken transportation crates naturally contaminated with food and fecal residues were investigated. Aerobic counts of 5.0 to 6.0 log CFU/24 cm(2) and an Enterobacteriaceae spp. level of 2.0 CFU/24 cm(2) were found on the surfaces prior to the treatment. After 1 s of treatment, the aerobic counts were significantly (P conveyor belts with hinge pins and one type of flat flexible rubber belt, all visibly contaminated with food residues. The aerobic counts of 3.0 to 5.0 CFU/50 cm(2) were significantly (P < 0.05) reduced, while Enterobacteriaceae spp. were reduced to a level below the detection limit. Industrial meat knives were contaminated with aerobic counts of 6.0 log CFU/5 cm(2) on the handle and 5.2 log CFU/14 cm(2) on the steel. The level of Enterobacteriaceae spp. contamination was approximately 2.5 log CFU on the handle and steel. Two seconds of steam-ultrasound treatment reduced the aerobic counts and Enterobacteriaceae spp. to levels below the detection limit on both handle and steel. This study shows that the steam-ultrasound treatment may be an effective replacement for disinfection processes and that it can be used for continuous disinfection at fast process lines. However, the treatment may not be able to replace efficient cleaning processes used to remove high loads of debris.

Method and apparatus for scientific analysis under low temperature vacuum conditions

Science.gov (United States)

Winefordner, James D.; Jones, Bradley T.

1990-01-01

A method and apparatus for scientific analysis of a sample under low temperature vacuum conditions uses a vacuum chamber with a conveyor belt disposed therein. One end of the conveyor belt is a cool end in thermal contact with the cold stage of a refrigerator, whereas the other end of the conveyor belt is a warm end spaced from the refrigerator. A septum allows injection of a sample into the vacuum chamber on top of the conveyor belt for spectroscopic or other analysis. The sample freezes on the conveyor belt at the cold end. One or more windows in the vacuum chamber housing allow spectroscopic analysis of the sample. Following the spectroscopic analysis, the conveyor belt may be moved such that the sample moves toward the warm end of the conveyor belt where upon it evaporates, thereby cleaning the conveyor belt. Instead of injecting the sample by way of a septum and use of a syringe and needle, the present device may be used in series with capillary-column gas chromatography or micro-bore high performance liquid chromatography.

Plant trial of an under-belt capacitance and gamma-ray backscatter gauge for on-belt determination of moisture in coal

International Nuclear Information System (INIS)

Cutmore, N.G.; Rafter, P.T.; Abernethy, D.A.; Millen, M.J.

1989-01-01

A non-contacting under-belt capacitance and gamma-ray backscatter technique has been developed for the on-line measurement of moisture in coal. In this technique, moisture was correlated with radio frequency susceptance and conductance, determined using an under-belt capacitance sensor in which a fringing electric field interrogates a layer of coal on the conveyor belt directly about the sensor. To compensate for variations in the density and thickness of the coal layer, an under-belt gamma-ray backscatter gauge was used to measure an equivalent volume of coal. A plant trial of the technique was conducted at Stockton Borehole Colliery, NSW Australia, where the gauges were installed on the coking coal product conveyor. Product moistures, in the range 7-14%, were determined with r.m.s errors of 0.50 and 0.25 wt% using on-belt and static off-belt gauges, respectively. The difference in the on-belt and off-belt gauge measurement accuracy was attributed to sampling errors in the calibration of the on-belt gauge. 6 refs., 6 figs., 3 tabs

Errors of isotope conveyor weigher caused by profile variations and shift of material

International Nuclear Information System (INIS)

Machaj, B.

1977-01-01

Results of investigations of isotope conveyor weigher in transmission geometry and with long plastic scintillator as a detector are presented in the paper. The results indicate that errors caused by material shift across the conveyor belt can be decreased by forming probe sensitivity to incident radiation along its axis by means of additional radiation absorbents. The errors caused by material profile variations can effectively be diminished by increase of photon energy. Application of 60 Co instead of 137 Cs ensured more than three times lower errors caused by profile variation. Errors caused by vertical movements of the belt with material, decrease considerably, when single point source situated in the center of the measuring head is replaced at least by two point sources situated out of the center, above the edges of the belt. (author)

Conveyor belt biomantles: Centripetal bioturbation coupled with erosional downwasting -- an explanatory model

Science.gov (United States)

Johnson, D. L.; Johnson, D. N.

2012-12-01

specifically, and in summary, we present a model that displays how semi-continuous biomechanical and centripetally driven constructional soil-sediment biotransfers to raised animal-produced point centers are concomitantly leveled by physical-erosional centrifugally driven, lateral-radial downwasting processes. The model is analogous to a cyclical conveyor belt system of soil-sediment biotransfers to, then erosionally away, from innumerably raised point centers, the "activity centers" of burrowing animals. Career-spanning fieldwork across many tropical, subtropical, and mid-latitude environments strongly support the overall validity of the model. Apart from microbes, animals represent the most diverse organismic group on the planet, with plants and fungi distant seconds. Moreover, many if not most spend at least part of their existence living on and/or in soil and sediment, which includes both the subaerial and subaqueous realms of Earth (that is, all of it, except extreme polar areas). Animals bioturbate, vertically and laterally, and likely have done so since pre-Cambrian time. The fundamental conveyor belt process, where ongoing centripetal bioturbations are coupled with ongoing erosional wasting and spreading, joined by subsidiary processes, drives biomantle formation.

ContiTronic - The intelligent conveyor belt from ContiTech; ContiTronic - Das intelligente Transportband von ContiTech

Energy Technology Data Exchange (ETDEWEB)

Alles, R; Wach, T [ContiTech Transportbandsysteme GmbH, Hannover (Germany)

1998-05-01

ContiTech has investigated the use of RFID (Radio Frequency Identification) and found that specially developed transponders can be vulcanized into rubber conveyor belts without impairing their performance capabilities. The system opens up a whole host of new applications in bulk materials handling within various sectors of industry (mining, steel industry, etc.). With the support of the Cologne-based Rheinbraun AG, the ContiTronic system was tested in lignite mining Operations in Hambach. (orig.) [Deutsch] Untersuchungen bei ContiTech ueber die Radio-Frequenz-Identifikation (RFID) ergaben, dass sich speziell entwickelte Transponder in Gummifoerdergurte einvulkanisieren lassen, ohne dass deren Funktion beeintraechtigt wird. Das System eroeffnet bei der Schuettgutfoerderung in den verschiedensten Industriebereichen (Bergbau, Stahlindustrie usw.) neue Anwendungen. Mit Unterstuetzung der Rheinbraun AG, Koeln, wurde das ContiTronic-System im Braunkohlentagebau Hambach erprobt. (orig.)

Variable-speed belt conveyor systems improve economy in operation; Drehzahlgeregelte Bandanlagen verbessern die betriebswirtschaftlichen Kennzahlen

Energy Technology Data Exchange (ETDEWEB)

Keller, C.; Neuffer, I.; Weber, D. [Siemens AG, Erlangen (Germany). Bereich Anlagenbau und Technische Dienstleistungen (ATD)

1999-03-01

Previous large conveyor system solutions were a compromise between mechanical design and electrical drive technology, usually based on slipring motors for cost reasons. Today`s power electronics systems now make it possible to use medium-voltage frequency converters in large conveyor systems. This new technology opens up design solutions with torque control that yield distinctly better behaviour under load fluctuation conditions, thereby reducing wear and tear. Experience gained from completed projects has shown that a higher-level load-dependent conveyor speed control can achieve energy savings of up to 20%, since material flows tend to be stochastic rather than constant. Maximum speed is required for short periods only and can therefore be obtained by means of field weakening, a higher gear ratio and short-time overshooting of the rated motor current. This permits the use of motors with smaller frame sizes. Furthermore, in view of the controlled torque and shorter belt runs, it is conceivable that built-in safety margins could be reduced. The solution presented here shows how a distinct improvement in cost efficiency can be attained. (orig.) [Deutsch] Bisherige Loesungen fuer grosse Bandanlagen sind ein Kompromiss zwischen mechanischer Konstruktion und elektrischer Antriebstechnik, bei der aus Kostengruenden meist Schleifringlaeufermotoren eingesetzt werden. Aufgrund der Moeglichkeiten, die die Leistungselektronik heute bietet, ist ein Einsatz von Mittelspannungsumrichtern auch auf diesem Gebiet realisierbar. Damit sind Loesungen moeglich, die besonders durch ein gefuehrtes Moment ein deutlich verbessertes Verhalten bei Momenten- oder Lastaenderungen herbeifuehren und damit eine materialschonende Betriebsweise ermoeglichen. Ausserdem hat sich bei ausgefuehrten Anlagen gezeigt, dass sich durch eine uebergeordnete foerderleistungsabhaengige Bandgeschwindigkeitsregelung auch Energie bis zu 20% einsparen laesst, da der Materialfluss nicht stetig, sondern eher

Plant trial of a fast neutron and gamma-ray transmission gauge for the on-belt determination of moisture in lump coke

International Nuclear Information System (INIS)

Millen, M.J.; Rafter, P.T.; Sowerby, B.D.; Rainbow, M.T.; Jelenich, L.

1990-01-01

A fast neutron and γ-ray transmission (FNGT) gauge has been used to determine the moisture content of lump coke on the conveyor belt supplying the No. 3 blast furnace at the BHP Newcastle Steelworks. The gauge was operated on-line over the period June 1988-March 1989. Gauge moisture was compared with laboratory moisture, based on 30 increment composite samples taken from the belt, and with moisture determined by a second FNGT gauge on one of the hoppers feeding the conveyor belt. The r.m.s. difference between conveyor gauge moisture and laboratory moisture was 0.24 wt% during the calibration period for two hopper flow on the belt, which is normal plant condition. The accuracy of the conveyor belt gauge was maintained to within 0.37 wt% moisture over the full period of the plant trial. (author)

Simulation of load traffic and steeped speed control of conveyor

Science.gov (United States)

Reutov, A. A.

2017-10-01

The article examines the possibilities of the step control simulation of conveyor speed within Mathcad, Simulink, Stateflow software. To check the efficiency of the control algorithms and to more accurately determine the characteristics of the control system, it is necessary to simulate the process of speed control with real values of traffic for a work shift or for a day. For evaluating the belt workload and absence of spillage it is necessary to use empirical values of load flow in a shorter period of time. The analytical formulas for optimal speed step values were received using empirical values of load. The simulation checks acceptability of an algorithm, determines optimal parameters of regulation corresponding to load flow characteristics. The average speed and the number of speed switching during simulation are admitted as criteria of regulation efficiency. The simulation example within Mathcad software is implemented. The average conveyor speed decreases essentially by two-step and three-step control. A further increase in the number of regulatory steps decreases average speed insignificantly but considerably increases the intensity of the speed switching. Incremental algorithm of speed regulation uses different number of stages for growing and reducing load traffic. This algorithm allows smooth control of the conveyor speed changes with monotonic variation of the load flow. The load flow oscillation leads to an unjustified increase or decrease of speed. Work results can be applied at the design of belt conveyors with adjustable drives.

The conveyor belt hypothesis for thymocyte migration: participation of adhesion and de-adhesion molecules.

Science.gov (United States)

Villa-Verde, D M; Calado, T C; Ocampo, J S; Silva-Monteiro, E; Savino, W

1999-05-01

Thymocyte differentiation is the process by which bone marrow-derived precursors enter the thymus, proliferate, rearrange the genes and express the corresponding T cell receptors, and undergo positive and/or negative selection, ultimately yielding mature T cells that will represent the so-called T cell repertoire. This process occurs in the context of cell migration, whose cellular and molecular basis is still poorly understood. Kinetic studies favor the idea that these cells leave the organ in an ordered pattern, as if they were moving on a conveyor belt. We have recently proposed that extracellular matrix glycoproteins, such as fibronectin, laminin and type IV collagen, among others, produced by non-lymphoid cells both in the cortex and in the medulla, would constitute a macromolecular arrangement allowing differentiating thymocytes to migrate. Here we discuss the participation of both molecules with adhesive and de-adhesive properties in the intrathymic T cell migration. Functional experiments demonstrated that galectin-3, a soluble beta-galactoside-binding lectin secreted by thymic microenvironmental cells, is a likely candidate for de-adhesion proteins by decreasing thymocyte interaction with the thymic microenvironment.

Mapping organelle motion reveals a vesicular conveyor belt spatially replenishing secretory vesicles in stimulated chromaffin cells.

Science.gov (United States)

Maucort, Guillaume; Kasula, Ravikiran; Papadopulos, Andreas; Nieminen, Timo A; Rubinsztein-Dunlop, Halina; Meunier, Frederic A

2014-01-01

How neurosecretory cells spatially adjust their secretory vesicle pools to replenish those that have fused and released their hormonal content is currently unknown. Here we designed a novel set of image analyses to map the probability of tracked organelles undergoing a specific type of movement (free, caged or directed). We then applied our analysis to time-lapse z-stack confocal imaging of secretory vesicles from bovine Chromaffin cells to map the global changes in vesicle motion and directionality occurring upon secretagogue stimulation. We report a defined region abutting the cortical actin network that actively transports secretory vesicles and is dissipated by actin and microtubule depolymerizing drugs. The directionality of this "conveyor belt" towards the cell surface is activated by stimulation. Actin and microtubule networks therefore cooperatively probe the microenvironment to transport secretory vesicles to the periphery, providing a mechanism whereby cells globally adjust their vesicle pools in response to secretagogue stimulation.

QUALITATIVE ANALYSIS OF DEPENDENCE OF DRIVE POWER HORIZONTAL-INCLINED BELT CONVEYOR ON ITS INITIAL PARAMETERS

Directory of Open Access Journals (Sweden)

V. M. Bohomaz

2017-02-01

Full Text Available Purpose.One of the main elements of band conveyors is a drive. To analyze the effect of design parameters on the drive power it is necessary to carry out the calculations according to standard procedures outlined in the current technical literature. The main design parameters of the band conveyor are: the type of cargo, project performance, the geometric dimensions of sections and track configuration as a whole. The feature of band conveyor calculation as compared to the elevators is the dependence of the band width on its performance, the inclination angle and the type of cargo. In the article for the account of this fact during calculations it is necessary to construct the dependence of the band width on the generalized parameter, which takes into account change in the design parameters. To determine the general pattern of changing the value of band conveyor drive power when varying its design parameters in the article it is necessary to construct the corresponding graphic dependences taking into account the standard sizes and bands parameters. Methodology. We consider the band conveyor with two sections: the inclined and horizontal one. It is conducted a detailed analysis of dependence of the conveyor band width and its drive power on the type of cargo, project performance, geometric dimensions and configuration of the conveyor track, using the appropriate parameter dependences constructed by the authors in previous papers. Findings. For band conveyors of this type there were constructed the graphics dependences of the band width on the parameter characterizing the project performance and the inclination angle of the track section, and on the performance at a fixed angle of inclination. Taking into account the changes in the band width with an increase in the value of project performance the graph dependences of drive power on the productivity and the inclination angle of the inclined section were built. Originality. For the first time there

MONITORING KEMAJUAN PENGERJAAN PROYEK BELT CONVEYOR PLANT 14 HAMBALANG BERBASIS WEB

Directory of Open Access Journals (Sweden)

Juliana Juliana

2018-04-01

Full Text Available Kriteria yang harus dipenuhi produk yang dihasilkan dari proyek meliputi kriteria atau batasan waktu, batasan ruang lingkup, batasan biaya dan batasan kualitas. Untuk itu, maka perlu dilakukan monitoring untuk mengetahui kemajuan proyek sehingga keempat kriteria tersebut terpenuhi. Progress atau kemajuan proyek menjadi indikator dalam monitoring untuk menilai perkembangan pelaksanaan pekerjaan dibandingkan dengan rencana. Perkembangan pelaksanaan proyek harus dilaporkan secara periodik. Pada pelaksanaan proyek pembangunan belt conveyor plant 14 Hambalang, PT Unixindo Ekatama Sentana dalam melakukan monitoring perkembangan proyek belum ada sistem pelaporan yang terintegrasi dan pengolahan data masih dilakukan secara manual dengan menggunakan aplikasi Ms.Excel. Dalam penelitian ini dibangun sistem informasi monitoring pelaporan proyek untuk memudahkan monitoring kemajuan proyek. Aplikasi untuk monitoring kemajuan proyek yang dibangun dengan berbasis web menggunakan PHP dan MySQL. Tujuan dari penelitian yang dilakukan yaitu untuk menghasilkan sistem informasi untuk melakukan monitoring kemajuan proyek berbasis web dan tersedia sistem pelaporan kemajuan proyek yang terintegrasi sehingga memudahkanperusahaan dalam memonitoring proyek secara online. Manfaat yang diharapkan dari adanya sistem monitoring kemajuan proyek secara online adalah memudahkan proses monitoring kemajuan proyek yang dapat dilakukan secara online. Dari penelitian dihasilkan sistem informasi monitoring yang dibuat memudahkan pelaporan proyek di lapangan yang dilakukan secara online sehingga perusahaan dapat memonitor kemajuan proyek secara kontinyu dan dapat digunakan untuk menilai perkembangan pekerjaan proyek yang dibandingkan dengan perencanaan proyek sehingga dapat mengambil keputusan untuk melakukan perbaikan. Kata kunci: kemajuan proyek, pelaporan proyek, monitoring proyek berbasis web.

Role of the Bering Strait on the hysteresis of the ocean conveyor belt circulation and glacial climate stability.

Science.gov (United States)

Hu, Aixue; Meehl, Gerald A; Han, Weiqing; Timmermann, Axel; Otto-Bliesner, Bette; Liu, Zhengyu; Washington, Warren M; Large, William; Abe-Ouchi, Ayako; Kimoto, Masahide; Lambeck, Kurt; Wu, Bingyi

2012-04-24

Abrupt climate transitions, known as Dansgaard-Oeschger and Heinrich events, occurred frequently during the last glacial period, specifically from 80-11 thousand years before present, but were nearly absent during interglacial periods and the early stages of glacial periods, when major ice-sheets were still forming. Here we show, with a fully coupled state-of-the-art climate model, that closing the Bering Strait and preventing its throughflow between the Pacific and Arctic Oceans during the glacial period can lead to the emergence of stronger hysteresis behavior of the ocean conveyor belt circulation to create conditions that are conducive to triggering abrupt climate transitions. Hence, it is argued that even for greenhouse warming, abrupt climate transitions similar to those in the last glacial time are unlikely to occur as the Bering Strait remains open.

Increased productivity in construction of civil and mining tunnels through the use of high-capacity tunnel-boring machines and continuous belt conveyor muck haulage

Energy Technology Data Exchange (ETDEWEB)

Beatty, J.G.; Ganey, R.J.; Killingsworth, J.E. [Perini Corp., Chicago, IL (United States). US Heavy Division

1994-12-31

The use of a large diameter high production tunnel boring machine interfaced with a high capacity continuous belt conveyor system provides a highly productive and cost effective construction system for both civil and mining tunnels. Continuous advance of the tunnel boring machine for a distance of 1,000 feet (305 m) allows for very efficient operation of the system. The available cost reductions will likely prove that this approach to waste handling will make marginally viable projects economically feasible. 9 refs., 10 figs., 1 tab.

Ammonia and methane emissions during drying of dewatered biogas digestate in a two-belt conveyor dryer.

Science.gov (United States)

Awiszus, S; Meissner, K; Reyer, S; Müller, J

2018-01-01

Aim of the present study was to identify type and amount of emissions during the drying of biogas digestate in a two-belt conveyor dryer at different temperature settings and to investigate the effect on its nutrient content. Furthermore, the possibility of recovering nitrogen from the exhaust air was investigated. Emissions of CH 4 , CO 2 and NH 3 were measured by Fourier transform infrared spectroscopy. Biogas is mainly composed of CH 4 and CO 2 , hence gas release from the digestate during drying was expected to increase the concentration of these components. Although CO 2 concentration was elevated above the background concentration, CH 4 did not exceed the background concentration. Maximum NH 3 concentration of 183.3mg·m -3 was detected during drying. A NH 3 concentration of 10.8mg·m -3 was measured in the exhaust air of the ammonia scrubber, which is equal to a NH 3 reduction rate of 94%. Copyright © 2017 Elsevier Ltd. All rights reserved.

Current methods and possibilities to determine the variability of Cu content in the copper ore on a conveyor belt in one of KGHM Polska Miedz S.A. mines

Directory of Open Access Journals (Sweden)

Jurdziak Leszek

2016-01-01

Full Text Available In this paper the methodology of ore sampling on a belt conveyor in one of KGHM Polska Miedz S.A. mines was presented together with the results of analysis of the variation of ore tonnage and quality. The ore was transferred from one mine to another one through the analysed transfer conveyor on the route from the mine Division of Mining to copper plants. The transported ore was sampled in person from Division of Concentrators on a regular basis for metal accounting purposes between both mines. The ore quality control became a significant problem since it is impossible to predict with satisfactory advance both Cu content in the feed as well as its lithology composition which is required to improve and optimise the enrichment efficiency.

A new proved field-tested system for early detection of smouldering fire at conveyor belt equipment; Ein neues betriebsreifes System zur Glimmbrandfrueherkennung an Gurtfoerderanlagen

Energy Technology Data Exchange (ETDEWEB)

Wick, H. [Bezirksregierung Arnsberg, Abt. Bergbau und Energie in NRW, Dortmund (Germany); Misz, Thomas [Zentralstab Kernbereich, RAG Deutsche Steinkohle AG, Herne (Germany)

2009-11-05

In underground mining, a CO (carbon oxide)-monitoring is not suitable, to detect a beginning fire in a very early stage and at its place of origin, especially when the ventilation current is very high. By the fibre-optical supervision system GESO, an additional early warning system was developed, which is very safe. It is used especially for belt conveyors in underground roadways. The technology for service temperature measurement, developed and extended for use in explosive atmosphere is state-of-the-art in industries on the surface. (orig.)

The conveyor belt hypothesis for thymocyte migration: participation of adhesion and de-adhesion molecules

Directory of Open Access Journals (Sweden)

Villa-Verde D.M.S.

1999-01-01

Full Text Available Thymocyte differentiation is the process by which bone marrow-derived precursors enter the thymus, proliferate, rearrange the genes and express the corresponding T cell receptors, and undergo positive and/or negative selection, ultimately yielding mature T cells that will represent the so-called T cell repertoire. This process occurs in the context of cell migration, whose cellular and molecular basis is still poorly understood. Kinetic studies favor the idea that these cells leave the organ in an ordered pattern, as if they were moving on a conveyor belt. We have recently proposed that extracellular matrix glycoproteins, such as fibronectin, laminin and type IV collagen, among others, produced by non-lymphoid cells both in the cortex and in the medulla, would constitute a macromolecular arrangement allowing differentiating thymocytes to migrate. Here we discuss the participation of both molecules with adhesive and de-adhesive properties in the intrathymic T cell migration. Functional experiments demonstrated that galectin-3, a soluble ß-galactoside-binding lectin secreted by thymic microenvironmental cells, is a likely candidate for de-adhesion proteins by decreasing thymocyte interaction with the thymic microenvironment.

Modelling and control algorithms of the cross conveyors line with multiengine variable speed drives

Science.gov (United States)

Cheremushkina, M. S.; Baburin, S. V.

2017-02-01

The paper deals with the actual problem of developing the control algorithm that meets the technical requirements of the mine belt conveyors, and enables energy and resource savings taking into account a random sort of traffic. The most effective method of solution of these tasks is the construction of control systems with the use of variable speed drives for asynchronous motors. The authors designed the mathematical model of the system ‘variable speed multiengine drive - conveyor - control system of conveyors’ that takes into account the dynamic processes occurring in the elements of the transport system, provides an assessment of the energy efficiency of application the developed algorithms, which allows one to reduce the dynamic overload in the belt to 15-20%.

Estimation of physical work load by statistical analysis of the heart rate in a conveyor-belt worker.

Science.gov (United States)

Kontosic, I; Vukelić, M; Pancić, M; Kunisek, J

1994-12-01

Physical work load was estimated in a female conveyor-belt worker in a bottling plant. Estimation was based on continuous measurement and on calculation of average heart rate values in three-minute and one-hour periods and during the total measuring period. The thermal component of the heart rate was calculated by means of the corrected effective temperature, for the one-hour periods. The average heart rate at rest was also determined. The work component of the heart rate was calculated by subtraction of the resting heart rate and the heart rate measured at 50 W, using a regression equation. The average estimated gross energy expenditure during the work was 9.6 +/- 1.3 kJ/min corresponding to the category of light industrial work. The average estimated oxygen uptake was 0.42 +/- 0.06 L/min. The average performed mechanical work was 12.2 +/- 4.2 W, i.e. the energy expenditure was 8.3 +/- 1.5%.

Perancangan Prototype Early Warning System pada Kontrol On/Off Belt Conveyor Menggunakan PLC Siemens S7-300

Directory of Open Access Journals (Sweden)

Taufik Taufik

2016-04-01

Full Text Available Nowadays, automation system become an important aspect of the manufacturing process because could make integration manufacturing process on it more effective and more efficient. PLC or Programmable Logic Controller is one kind of automation system. Many industries use PLC as automation control device in the manufacturing process to control all kind of process. For example at transportation process of coals in generator industry. Coals could be burned because main elements of coals are carbon, hydrogen, and oxygen. Base on this prototype early warning system design, we get the result if sensor thermocouple detects temperature larger than setpoint temperature (it is 2000C, then PLC will give an order to shut down the output, that is a belt conveyor. The result of this prototype design could use at coals transportation as an early warning system. The design of prototype early warning system could detect and prevent fire because of the consequence of burned coals until spreading of fire could be avoided.

Determination of ash concentration and coal calorific values of coal directly on the conveyor belt; Bestimmung der Aschegehalte und Heizwerte von Kohlen direkt auf dem Foerderband

Energy Technology Data Exchange (ETDEWEB)

Wess, Juergen [PANalytical GmbH, Kassel (Germany)

2012-07-01

Among the multi-element methods of instrumental analyses, the neutron activation analysis takes a special position. The method is able to penetrate even thick layers of samples and covers whole mass flows online, like on conveyor belts. A new technique of pulsed excitation allows the reduction of undesired components of analytical gamma-rays, which allows the determination of carbon, oxygen and hydrogen. Therefore, the ash content, based on the ash containing elements, and the calorific values, based on calculation models, can be measured in one process. (orig.)

Design of conveyor chutes with special attention to blockage, wear and conveyor detection change

Energy Technology Data Exchange (ETDEWEB)

Arnold, P C; Hill, G L [University of Wollongong, Wollongong, NSW (Australia). Dept. of Mechanical Engineering

1991-04-01

Coal handling continues to present industry with significant problems which, to overcome, result in the expenditure of considerable sums of money. While there are considerable efforts being made to reduce coal production costs, materials handling which represents a large proportion of those costs, is still a generally neglected area. This project has demonstrated that many of the problems of existing transfer areas can be overcome by the use of a small mass-flow bin and belt feeder combination, particularly for the case of high speed belts where many of these problems are further amplified. The study has emphasised the need to begin chute designs with an assessment of the flow properties of the bulk solid, once these have been established an accurate plot of the material's trajectory is required before the design of any type of chute can commence. It has been shown that surge bin transfer chutes would have particular application in: high speed belt conveying; transfer of fragile materials prone to degradation and dusting; more than one conveyor to be fed from a single belt; transfers at any angle with high efficiency. Throughout this project these aspects have been studied. Techniques for predicting feeder loads and power requirements are recommended, and ways of predicting the exit velocity from impact plates have been studied. The influence of gates and feeder angles on mass flow rates from high velocity belt feeders is reported.

Design of a nucleonic conveyor belt weighing machine

International Nuclear Information System (INIS)

Magal, B.S.; Sunder Singh, V.P.

1979-01-01

A brief literature survey of the existing conventional units and the nucleonic belt weigher is made. The design of a 250 ton per hour coal weighing unit working in conjunction with a 24 inch wide belt, running at 350 feet per minute has been attempted and a unit has been built to the above specifications. Caseium-137 line source has been used as an isotope and a 10 litre volume argon filled ionisation chamber has been used as a detector. A line source has been preferred to a point source. The unit is under trial and the accuracy of the same is being evaluated by changing the variables like particle size profile of the material deposited on the belt and sudden changes in loading. Initial trials indicate that an accuracy of +- 1 p.c. can be achieved. (auth.)

Radiometric measurement independent of profile. Belt weighers

International Nuclear Information System (INIS)

Otto, J.

1986-01-01

Radiometric measuring techniques allow contactless determination of the material carried by belt conveyors. Data defining the material is obtained via attenuation of gamma rays passing through the material on the belt. The method applies the absorption law according to Lambert-Beer, which has to be corrected by a build-up factor because of the stray radiation induced by the Compton effect. The profile-dependent error observed with conventional radiometric belt weighers is caused by the non-linearity of the absorption law in connection with the simultaneous summation of the various partial rays in a detector. The scanning method allows separate evaluation of the partial rays' attenuation and thus yields the correct data of the material carried, regardless of the profile. The scanning method is applied on a finite number of scanning sections, and a residual error has to be taken into account. The stochastics of quantum emission and absorption leads to an error whose expectation value is to be taken into account in the scanning algorithm. As the conveyor belt is in motion during the process of measurements, only part of the material conveyed is irradiated. The resulting assessment error is investigated as a function of the autocorrelation function of the material on the belt. (orig./HP) [de

Conveying technology to new heights

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-07-15

In the quest for greater performance and efficiency, operators are increasingly looking for more sophisticated conveying solutions. ThyssenKrupp Foerdertechnik (TKF) now manufactures pipe conveyors, joining the established firm Sicon. ContiTech is developing new rubber compositions to reduce rolling resistance in its conveyor systems. ContiClean A-H is a new anti-stick conveyor belt. Kinder & Co. investigated materials to replace the conventional rubber seal. Polyurethane was found to have the best coefficient of friction. A K-Kryptane polyethylene belt skinting has been fitted on a quay conveyor to a ship loader and has reduced wear considerably. 2 photos.

30 CFR 77.407 - Power-driven pulleys.

Science.gov (United States)

2010-07-01

... equipment especially designed for hand feeding. (b) Pulleys of conveyors shall not be cleaned manually while the conveyor is in motion. ... for Mechanical Equipment § 77.407 Power-driven pulleys. (a) Belts, chains, and ropes shall not be...

Powerful conveyer belt real-time online detection system based on x-ray

Science.gov (United States)

Rong, Feng; Miao, Chang-yun; Meng, Wei

2009-07-01

The powerful conveyer belt is widely used in the mine, dock, and so on. After used for a long time, internal steel rope of the conveyor belt may fracture, rust, joints moving, and so on .This would bring potential safety problems. A kind of detection system based on x-ray is designed in this paper. Linear array detector (LDA) is used. LDA cost is low, response fast; technology mature .Output charge of LDA is transformed into differential voltage signal by amplifier. This kind of signal have great ability of anti-noise, is suitable for long-distance transmission. The processor is FPGA. A IP core control 4-channel A/D convertor, achieve parallel output data collection. Soft-core processor MicroBlaze which process tcp/ip protocol is embedded in FPGA. Sampling data are transferred to a computer via Ethernet. In order to improve the image quality, algorithm of getting rid of noise from the measurement result and taking gain normalization for pixel value is studied and designed. Experiments show that this system work well, can real-time online detect conveyor belt of width of 2.0m and speed of 5 m/s, does not affect the production. Image is clear, visual and can easily judge the situation of conveyor belt.

A case study on the formation and evolution of ice supersaturation in the vicinity of a warm conveyor belt's outflow region

Directory of Open Access Journals (Sweden)

P. Spichtinger

2005-01-01

Full Text Available A case study is presented on the formation and evolution of an ice-supersaturated region (ISSR that was detected by a radiosonde in NE Germany at 06:00 UTC 29 November 2000. The ISSR was situated in the vicinity of the outflow region of a warm conveyor belt associated with an intense event of cyclogenesis in the eastern North Atlantic. Using ECMWF analyses and trajectory calculations it is determined when the air parcels became supersaturated and later subsaturated again. In the case considered, the state of air parcel supersaturation can last for longer than 24h. The ISSR was unusually thick: while the mean vertical extension of ISSRs in NE Germany is about 500m, the one investigated here reached 3km. The ice-supersaturated region investigated was bordered both vertically and horizontally by strongly subsaturated air. Near the path of the radiosonde the ISSR was probably cloud free, as inferred from METEOSAT infrared images. However, at other locations within the ISSR it is probable that there were cirrus clouds. Relative humidity measurements obtained by the Lindenberg radiosonde are used to correct the negative bias of the ECMWF humidity and to construct two-dimensional maps of ice supersaturation over Europe during the considered period. A systematic backward trajectory analysis for the ISSRs on these maps shows that the ISSR air masses themselves experienced only a moderate upward motion during the previous days, whereas parts of the ISSRs were located just above strongly ascending air masses from the boundary layer. This indicates qualitatively that warm conveyor belts associated with mid-latitude cyclogenesis are disturbances that can induce the formation of ISSRs in the upper troposphere. The ISSR maps also lead us to a new perception of ISSRs as large dynamic regions of supersaturated air where cirrus clouds can be embedded at some locations while there is clear air at others.

Occupational exposure to rubber vulcanization products during repair of rubber conveyor belts in a brown coal mine

Energy Technology Data Exchange (ETDEWEB)

Gromiec, J.P.; Wesolowski, W.; Brzeznicki, S.; Wroblewska-Jakubowska, K.; Kucharska, M. [Nofer Institute of Occupational Medicine, Lodz (Poland)

2002-12-01

This study was carried out to identify chemical substances and measure their air concentrations in the repair shop of a brown coal mine in which damaged rubber conveyor belts were repaired. GC-MS and HPLC analysis of stationary air samples resulted in identification of aliphatic and aromatic hydrocarbons to C{sub 12}, PAHs, alcohols, phenols, ketones, heterocyclic nitrogen and sulfur compounds. Quantitative evaluation of occupational exposure included determination of organic compound vapours collected on charcoal (GC-MSD), polycyclic aromatic hydrocarbons (HPLC), N-nitrosoamines and other amines (GC-NPD) and DNPH derivatives of aldehydes (HPLC) in the breathing zone of workers representing all job titles. The concentrations of investigated compounds were very low. Carcinogenic substances: N-nitrosoamines, benzene, and PAHs were not present in workroom air in concentrations exceeding limits of detection of the analytical methods being applied; concentrations of methylisobutylketone, tetrachloroethylene, naphtha, aromatic hydrocarbons, phthalates and aldehydes were much lower than the respective occupational exposure limit values. The results indicate much lower exposure than that reported in the production of tyres and other fabricated rubber products.

Rebuilding conveyor transfer points to cut fugitive material and improve operations

Energy Technology Data Exchange (ETDEWEB)

Stahura, R P [Martin Engineering Company, Neponset, MA (USA)

1992-10-01

The article describes a three-part programme to control spillage and prevent fugitive material at conveyor transfer points. The three parts are: adequate belt support; the installation of a wear line inside the chute to preserve the rubber seal system; and the maintenance of an effective edge seal. The article also discusses designing for ease of maintenance. 9 figs.

Conceptual design of novel IP-conveyor-belt Weissenberg-mode data-collection system with multi-readers for macromolecular crystallography. A comparison between Galaxy and Super Galaxy.

Science.gov (United States)

Sakabe, N; Sakabe, K; Sasaki, K

2004-01-01

Galaxy is a Weissenberg-type high-speed high-resolution and highly accurate fully automatic data-collection system using two cylindrical IP-cassettes each with a radius of 400 mm and a width of 450 mm. It was originally developed for static three-dimensional analysis using X-ray diffraction and was installed on bending-magnet beamline BL6C at the Photon Factory. It was found, however, that Galaxy was also very useful for time-resolved protein crystallography on a time scale of minutes. This has prompted us to design a new IP-conveyor-belt Weissenberg-mode data-collection system called Super Galaxy for time-resolved crystallography with improved time and crystallographic resolution over that achievable with Galaxy. Super Galaxy was designed with a half-cylinder-shaped cassette with a radius of 420 mm and a width of 690 mm. Using 1.0 A incident X-rays, these dimensions correspond to a maximum resolutions of 0.71 A in the vertical direction and 1.58 A in the horizontal. Upper and lower screens can be used to set the frame size of the recorded image. This function is useful not only to reduce the frame exchange time but also to save disk space on the data server. The use of an IP-conveyor-belt and many IP-readers make Super Galaxy well suited for time-resolved, monochromatic X-ray crystallography at a very intense third-generation SR beamline. Here, Galaxy and a conceptual design for Super Galaxy are described, and their suitability for use as data-collection systems for macromolecular time-resolved monochromatic X-ray crystallography are compared.

Optimation of a Table Conveyor Type Grading Machine to Increase the Performance of Green Coffee Manual Sortation

Directory of Open Access Journals (Sweden)

Sukrisno Widyotomo

2006-05-01

Full Text Available Coffee consumers request a good quality of green coffee to get a good coffee cup taste. Defective beans e.g. black bean, brown bean and broken bean are associated to low coffee quality which give negative effects to final taste. To meet the standard export requirement, coffee beans have to be graded before being traded. Until now, grading process is generally carried out manually. The method gives better product, so the grading cost is very expensive about 40% of total processing cost. Meanwhile, shortage of skill workers is a limiting factor of the process. Therefore, improving the manual sorting by providing machine for grading of green coffee is good alternative to reduce the grading cost. Indonesian Coffee and Cocoa Research Institute has designed a table conveyor type grading machine in order to improve the performance of the manual grading productivity and consistent quality and to reduce the grading cost. The conveyor belt has a dimension of 5700 mm of length, 610 mm of width and 6 mm of thickness. The rotating of belt conveyor powered by an electro motor 3 HP, 3 phase and 1420 rpm. The result showed that the optimum capacity of grading machine was 390 kg/hour reached when the speed 16 rpm and 3 kg/m 2 of green beans on belt conveyor with productivity 1870 kg/man-day compared to the productivity full manually process 743 kg/man-day. Percentage of product in outlet 1 was 4.2% as broken beans, 0.26% as brown beans, 0.68% as one hole in beans and 0.61% as more than one hole in beans. Percentage of product in outlet 2 was 39.54% as broken beans, 4.23% as brown beans 7.19% as black beans, 4.47% as one hole in beans and 4.43% as more than one hole in beans. Cost of grading process per kg of green coffee is Rp20,-. Key words : Coffee, Grading, Conveyor table, Quality

Cleaning and Disinfection of Biofilms Composed of Listeria monocytogenes and Background Microbiota from Meat Processing Surfaces

Science.gov (United States)

Møretrø, Trond; Heir, Even; Briandet, Romain; Langsrud, Solveig

2017-01-01

ABSTRACT Surfaces of food processing premises are exposed to regular cleaning and disinfection (C&D) regimes, using biocides that are highly effective against bacteria growing as planktonic cells. However, bacteria growing in surface-associated communities (biofilms) are typically more tolerant toward C&D than their individual free-cell counterparts, and survival of pathogens such as Listeria monocytogenes may be affected by interspecies interactions within biofilms. In this study, Pseudomonas and Acinetobacter were the most frequently isolated genera surviving on conveyor belts subjected to C&D in meat processing plants. In the laboratory, Pseudomonas, Acinetobacter, and L. monocytogenes dominated the community, both in suspensions and in biofilms formed on conveyor belts, when cultures were inoculated with eleven-genus cocktails of representative bacterial strains from the identified background flora. When biofilms were exposed to daily C&D cycles mimicking treatments used in food industry, the levels of Acinetobacter and Pseudomonas mandelii diminished, and biofilms were instead dominated by Pseudomonas putida (65 to 76%), Pseudomonas fluorescens (11 to 15%) and L. monocytogenes (3 to 11%). The dominance of certain species after daily C&D correlated with high planktonic growth rates at 12°C and tolerance to C&D. In single-species biofilms, L. monocytogenes developed higher tolerance to C&D over time, for both the peracetic acid and quaternary ammonium disinfectants, indicating that a broad-spectrum mechanism was involved. Survival after C&D appeared to be a common property of L. monocytogenes strains, as persistent and sporadic subtypes showed equal survival rates in complex biofilms. Biofilms established preferentially in surface irregularities of conveyor belts, potentially constituting harborage sites for persistent contamination. IMPORTANCE In the food industry, efficient production hygiene is a key measure to avoid the accumulation of spoilage bacteria and

Cleaning and disinfection of biofilms composed of Listeria monocytogenes and background microbiota from meat processing surfaces.

Science.gov (United States)

Fagerlund, Annette; Møretrø, Trond; Heir, Even; Briandet, Romain; Langsrud, Solveig

2017-06-30

Surfaces of food processing premises are exposed to regular cleaning and disinfection (C&D) regimes, using biocides that are highly effective against bacteria growing as planktonic cells. However, bacteria growing in surface associated communities (biofilms) are typically more tolerant towards C&D than their individual free cells counterparts, and survival of pathogens such as Listeria monocytogenes may be affected by interspecies interactions within biofilms. In this study, Pseudomonas and Acinetobacter were the most frequently isolated genera surviving on conveyor belts subjected to C&D in meat processing plants. In the laboratory, Pseudomonas , Acinetobacter and L. monocytogenes dominated the community both in suspensions and in biofilms formed on conveyor belts, when cultures were inoculated with eleven-genera cocktails of representative bacterial strains from the identified background flora. When biofilms were exposed to daily C&D cycles, mimicking treatments used in food industry, the levels of Acinetobacter and Pseudomonas mandelii diminished, and biofilms were instead dominated by Pseudomonas putida (65-76%), Pseudomonas fluorescens (11-15%) and L. monocytogenes (3-11%). The dominance of certain species after daily C&D correlated with high planktonic growth rates at 12°C and tolerance to C&D. In single-species biofilms, L. monocytogenes developed higher tolerance to C&D over time, both for the peracetic acid and quaternary ammonium disinfectant, indicating that a broad-spectrum mechanism was involved. Survival after C&D appeared to be a common property of L. monocytogenes strains, as both persistent and sporadic subtypes showed equal survival in complex biofilms. Biofilms established preferentially in surface irregularities of conveyor belts, potentially constituting harborage sites for persistent contamination. IMPORTANCE In food industry, efficient production hygiene is a key measure to avoid accumulation of spoilage bacteria and eliminate pathogens

Pipe conveyors transport bulk material efficiently over long distances; Rohrgurtfoerderer transportieren Schuettgut effizient ueber lange Strecken

Energy Technology Data Exchange (ETDEWEB)

Will, Frank [BEUMER Maschinenfabrik GmbH und Co. KG, Beckum (Germany); Staribacher, Josef [KOCH Material Handling GmbH, Schwechat (Australia)

2011-05-15

The specific characteristics of a pipe conveyor, which are due to its operating principle, allow transportation solutions which are not possible with other conveyor systems; or if they are possible, then only with considerable restrictions or additional expenses. The enclosed design of the pipe conveyor protects the material from the environment and the environment from the conveyed material. The system, thus, makes a valuable contribution towards achieving environmental protection objectives and in meeting official regulations. The pipe conveyor handles both tight curve radiuses and steep inclines. This permits a very flexible route and also allows existing obstacles to be bypassed. Consequently, solutions can often be found which do not require any changes to be made to the existing terrain or plant structures. The investment costs of just the conveyor can sometimes be slightly higher for a pipe conveyor than for a conventional troughed belt conveyor. But if the pipe conveyor can take full advantage of its special features, then these additional costs become quite relative very quickly. And if, for example, transfer points, alterations of existing facilities, earthwork, or expensive dust and noise protection measures can be avoided due to the very flexible route layout of the pipe conveyor, then these savings on part of the customer are much higher than the additional costs for this perfect conveyor system. All told, it is possible to solve challenging conveying tasks with great efficiency while also saving resources when the pipe conveyor is used; thus, producing a sustained benefit to both the operator and the environment. (orig.)

Feed chute geometry for minimum belt wear

Energy Technology Data Exchange (ETDEWEB)

Roberts, A W; Wiche, S J [University of Newcastle, Newcastle, NSW (Australia). Centre for Bulk Solids and Particulate Technologies

1998-09-01

The paper is concerned with the feeding and transfer of bulk solids in conveyor belt operation. The paper focuses on chute design where the objective is to prevent spillage and minimise both chute and belt wear. It is shown that these objectives may be met through correct dynamic design of the chute and by directing the flow of bulk solids onto the belt at an acceptable incidence angle. The aim is to match the tangential velocity component of the feed velocity as close as possible to the belt velocity. At the same time, it is necessary to limit the impact pressure due to the change in momentum of the bulk solid as it feeds onto the belt. 2 refs., 8 figs.

Automation of belts; Automatizacion de Cintas de Interior

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

This document presents the most important aspects, and the results of the project DEVELOPMENT AND COMMISSIONING OF AN INTEGRATED HAULAGE AND VENTILATION CONTROL SYSTEM IN A MINE USING VERY LONG SUBLEVEL-CAVING WINNING METHOD. Project's targets were to develop, implement and commission a distributed control system for underground mining, which should allow the control and optimisation of the whole (continuous) haulage network. It should also integrate statutory safety features required for both winning and haulage. The system is capable of controlling the most common devices used in underground coal mining transport networks, like conveyor belts, armored conveyors, regulation silos, etc. from the winning faces to the surface, and also the interlocks between them. Moreover, the system implements statutory safety functions for conveyor belt operation, and for mining activities carried out in culls de sac. Specifically, for its relationship with the transport system, it should monitor secondary ventilation, fire damp and toxic gases concentration, and mains power presence in the culls de sac, which have already reached a length of 2000 m. The prototype was installed in the mine that Carbones de Pedraforca owns in Saldes, Barcelona. (Author)

Análisis estructural de un transportador de banda. // Structural analysis of a band conveyor.

Directory of Open Access Journals (Sweden)

P. Alvarez Barreras

2001-07-01

Full Text Available El presente trabajo contiene el análisis de comprobación de la estructura de la cuna de una máquina transportadora debanda. En el mismo se determinan las cargas de servicio y las condiciones de apoyo, se efectúa el cálculo lineal por elmétodo de los elementos finitos, y finalmente se valoran los resultados en forma de:· Análisis de las tensiones.· Análisis de los desplazamientos.· Análisis de las deformaciones.Palabras claves: Transportador de banda, estructura, análisis de tensiones, elementos finitos.________________________________________________________________________________AbstractThe present work contains the structure analysis of a belt conveyor cradle. The operation loads and conditions of supportare determined, the lineal calculation is made by the Finite Element Method, and finally the results are valued in form of:· Analysis of tensions.· Analysis of displacements.· Analysis of deformations.Key words: Belt conveyor cradle, structure, tension analysis, finite element.

The design of RFID convey or belt gate systems using an antenna control unit.

Science.gov (United States)

Park, Chong Ryol; Lee, Seung Joon; Eom, Ki Hwan

2011-01-01

This paper proposes an efficient management system utilizing a Radio Frequency Identification (RFID) antenna control unit which is moving along with the path of boxes of materials on the conveyor belt by manipulating a motor. The proposed antenna control unit, which is driven by a motor and is located on top of the gate, has an array structure of two antennas with parallel connection. The array structure helps improve the directivity of antenna beam pattern and the readable RFID distance due to its configuration. In the experiments, as the control unit follows moving materials, the reading time has been improved by almost three-fold compared to an RFID system employing conventional fixed antennas. The proposed system also has a recognition rate of over 99% without additional antennas for detecting the sides of a box of materials. The recognition rate meets the conditions recommended by the Electronic Product Code glbal network (EPC)global for commercializing the system, with three antennas at a 20 dBm power of reader and a conveyor belt speed of 3.17 m/s. This will enable a host of new RFID conveyor belt gate systems with increased performance.

Performance of a convective, infrared and combined infrared- convective heated conveyor-belt dryer.

Science.gov (United States)

El-Mesery, Hany S; Mwithiga, Gikuru

2015-05-01

A conveyor-belt dryer was developed using a combined infrared and hot air heating system that can be used in the drying of fruits and vegetables. The drying system having two chambers was fitted with infrared radiation heaters and through-flow hot air was provided from a convective heating system. The system was designed to operate under either infrared radiation and cold air (IR-CA) settings of 2000 W/m(2) with forced ambient air at 30 °C and air flow of 0.6 m/s or combined infrared and hot air convection (IR-HA) dryer setting with infrared intensity set at 2000 W/m(2) and hot at 60 °C being blown through the dryer at a velocity of 0.6 m/s or hot air convection (HA) at an air temperature of 60 °C and air flow velocity 0.6 m/s but without infrared heating. Apple slices dried under the different dryer settings were evaluated for quality and energy requirements. It was found that drying of apple (Golden Delicious) slices took place in the falling rate drying period and no constant rate period of drying was observed under any of the test conditions. The IR-HA setting was 57.5 and 39.1 % faster than IR-CA and HA setting, respectively. Specific energy consumption was lower and thermal efficiency was higher for the IR-HA setting when compared to both IR-CA and HA settings. The rehydration ratio, shrinkage and colour properties of apples dried under IR-HA conditions were better than for either IR-CA or HA.

Feasibility of surface sampling in automated inspection of concrete aggregates during bulk transport on a conveyor

NARCIS (Netherlands)

Bakker, M.C.M.; Di Maio, F.; Lotfi, S.; Bakker, M.; Hu, M.; Vahidi, A.

2017-01-01

Automated optic inspection of concrete aggregates for pollutants (e.g. wood, plastics, gypsum and brick) is required to establish the suitability for reuse in new concrete products. Inspection is more efficient when directly sampling the materials on the conveyor belt instead of feeding them in a

A new on-belt elemental analyzer for the cement industry

International Nuclear Information System (INIS)

Sowerby, B.D.; Lim, C.S.; Tickner, J.R.; Manias, C.; Retallack, D.

2001-01-01

On-line control of raw mill feed composition is a key to the improved control of cement plants. Elements of primary importance to the industry are calcium, silicon, aluminum and iron. Direct on-conveyor belt analysis of raw mill feed is required, independent of changes in belt loading, moisture content, and both horizontal and vertical segregation. A new and improved on-conveyor belt elemental analyzer for cement raw mill feed has been developed and tested successfully in Adelaide Brighton's Birkenhead cement plant. The analyzer utilizes two 241 Am-Be neutron sources and multiple BGO detectors to measure both neutron inelastic scatter and thermal neutron capture gamma rays. Dynamic tests in the plant on highly segregated material having depths in the range 100 to 200 mm have shown analyzer total RMS errors of 0.49, 0.52, 0.38 and 0.23 wt.% (on a loss free basis) for CaO, SiO 2 , Al 2 O 3 , and Fe 2 O 3 respectively, when 10-minute counting periods are used

Sandvik's HM 150 roller in action on the world's largest conveyor bridge in the Lusatia region; Sandvik HM 150 auf der weltgroessten Foerderbruecke in der Lausitz im Einsatz

Energy Technology Data Exchange (ETDEWEB)

Waliczek, Sven; Raddatz, Ulrich [Sandvik Mining and Construction Central Europe GmbH, Essen (Germany)

2010-09-15

Prince Herrmann Ludwig Heinrich von Pueckler-Muskau, a landscape gardening genius, built the Muskau Park in the Lusatia region in 1817 - it is part of a UNESCO world heritage site today. In the same era, 1850, the first lignite was mined in the region and still today, Vattenfall, the Swedish company, extracts lignite without subsidies - in Jaenschwalde among other places, one out of the five opencast mines currently in operation. As one of the largest employers and apprenticing companies in East Germany, Vattenfall currently employs almost 8000 employees and about 800 apprentices. Sandvik Mining and Construction also plays a leading role - in the literal sense. At the Jaenschwalde location there are 320 sets of 5-roller garlands of HM150 formed rollers in action on the overburden conveyor bridge AFB 60m (Figure 1) - on belt five, the main belt conveyor (belt type 3000 ST3000-18:8, idler spacing approx. 800 mm) and on belt eight, the stockpile belt conveyor (belt type 2750 ST2500-18:8, idler spacing approx. 800 mm). It all began in the spring of 2004. Bernhard Hofmayer, Production Manager at Sandvik, introduced the HM150 formed roller to Vattenfall. The engineers were impressed by the completely new design and the innovative assembly technique. The discussion about the advantages and disadvantages of the component optimised formed roller were ready to begin. (orig.)

Aircraft measurements within a warm conveyor belt during the T-NAWDEX-FALCON campaign

Science.gov (United States)

Schäfler, Andreas; Boettcher, Maxi; Borrmann, Stephan; Busen, Reinhold; Dörnbrack, Andreas; Grams, Christian; Kaufmann, Stefan; Klingebiel, Marcus; Lammen, Yannick; Reutter, Philipp; Rautenhaus, Marc; Schlager, Hans; Sodemann, Harald; Voigt, Christiane; Wernli, Heini

2013-04-01

Warm Conveyor Belts (WCBs) are air streams that are highly relevant for the dynamics in the mid-latitudes as they strongly influence the evolution and intensity of northern hemispheric mid-latitude weather systems. For the predictability of cyclones the representation of diabatic processes associated with latent heat release due to phase transitions of water, surface fluxes, or radiative effects are believed to be a limiting factor. Diabatic processes in cyclones strongly depend on the transport of water vapor and are mainly organized and controlled by the coherently ascending WCB air masses. In October 2012 the T-NAWDEX-Falcon (THORPEX-North Atlantic Waveguide and Downstream Impact Experiment) campaign was organized by DLR Oberpfaffenhofen and ETH Zurich. During 9 research flights over Europe in-cloud measurements in WCBs were obtained with the DLR aircraft Falcon. Lagrangian flights were conducted with the aim to measure in the same air mass during different stages of the WCB to quantify the transport of moisture and the net latent heating along WCBs and their importance for forecast errors associated with mid-latitude weather systems. Besides in-situ observations of wind, temperature and humidity to characterize the thermodynamic structure of the WCBs, a set of dropsondes was deployed to gain a complete view on the complex structure of the cyclone. This presentation gives an overview of the three successful IOPs performed during the T-NAWDEX-Falcon campaign. To address forecast uncertainty and to enable flight planning up to four days in advance of the flights novel diagnostics based on deterministic and ensemble prediction NWP data were employed during the campaign. Furthermore a number of different trajectory models were applied for this field experiment. Based on selected flights from one intensive observation period the challenging planning process of Lagrangian matches of flight paths is described and first results are presented.

A Positive Feedback Process Between Tropical Cyclone Intensity and the Moisture Conveyor Belt Assessed With Lagrangian Diagnostics

Science.gov (United States)

Fujiwara, Keita; Kawamura, Ryuichi; Hirata, Hidetaka; Kawano, Tetsuya; Kato, Masaya; Shinoda, Taro

2017-12-01

Using a cloud-resolving regional model and Lagrangian diagnostics, we assess a positive feedback process between tropical cyclone (TC) intensity and the moisture conveyor belt (MCB), which connects a TC and the Indian Ocean (IO), the South China Sea (SCS), and the Philippine Sea (PS) vapors, from a macroscopic view. We performed sensitivity experiments that modified the observed sea surface temperature field over the IO and the SCS to regulate the MCB behavior, and we examined the remote response of a prototypical TC. The results show that the connection between MCB formation and TC development is very robust, which was also observed in another TC's case. The MCB plays a vital role in transporting lots of moist air parcels toward the TC from the IO, SCS, and PS regions. The transported parcels, which further gained the underlying ocean vapor along the MCB, are easily trapped in the inner core by radial inflow in the atmospheric boundary layer and, subsequently, release latent heat around the eyewall, resulting in the TC's intensifying. This acts to further penetrate the moist parcels of remote ocean origin into the inner core through the enhanced and expanded inflow. An additional experiment suggested that the MCB is not formed unless the westward propagation of equatorial waves induced by TC heating overlaps with the background monsoon westerlies. These findings support the reliability and validity of TC-MCB feedback.

A positive feedback process between tropical cyclone intensity and the moisture conveyor belt assessed with Lagrangian diagnostics

Science.gov (United States)

Fujiwara, K.; Kawamura, R.; Hirata, H.; Kawano, T.

2017-12-01

Using a cloud-resolving regional model and Lagrangian diagnostics, we assess a positive feedback process between tropical cyclone (TC) intensity and the moisture conveyor belt (MCB), which connects a TC and the Indian Ocean (IO), the South China Sea (SCS), and the Philippine Sea vapors, from a macroscopic view. We performed sensitivity experiments that modified the observed sea surface temperature (SST) field over the IO and the SCS to regulate the MCB behavior, and we examined the remote response of a prototypical TC. The results show that the connection between MCB formation and TC development is very robust, which was also observed in another TC's case. The MCB plays a vital role in transporting lots of moist air parcels toward the TC from the remote ocean. The transported parcels are easily trapped in the inner core by radial inflow in the atmospheric boundary layer and, subsequently, release latent heat around the eye wall, resulting in the TC's intensifying. This acts to further penetrate the moist parcels of remote ocean origin into the inner core through the enhanced and expanded inflow. An additional experiment confirmed that the MCB is not formed unless the westward propagation of equatorial Rossby waves induced by TC heating overlaps with the background monsoon westerlies. These findings support the reliability and validity of TC-MCB feedback.

Conveyor for sorting radioactive waste

International Nuclear Information System (INIS)

Prisco, A.J.; Johnson, A.N.

1987-01-01

An apparatus is described for detecting radioactive components in dry active waste, the apparatus comprising: means for reducing the waste to pieces of substantially uniform size, first and second conveyors and a housing for the conveyors; means for conveying the pieces from the means for reducing the waste to the first and second conveyors; each of the first and second conveyors includes a receiving portion and a discharge portion; the discharge portion is spaced above and upstream from the receiving portion to disperse the pieces as they are transferred from the first conveyor to the second conveyor so that pieces which are in clusters are separated from each other to increase the likelihood of detecting radiation emanating means for detecting radioactive radiation emanating from the pieces, at least one of radiation detector means is located on each of the conveyors. Each is disposed in close overlying relation to its respective conveyor so that low levels of radiation emanating from the pieces can be detected; each of the conveyors includes means for flattening the pieces of waste before the pieces pass under the radiation detector means; and the means for flattening disposed between the receiving portion of each conveyor and the radiation detector means; the housing is generally closed; and means for providing a generally closed connection between the housing and the means for reducing the waste so that air that is in the housing and in the means for reducing the waste can be controlled

A contribution to problems of clean transport of bulk materials

Directory of Open Access Journals (Sweden)

Fedora Jaroslav

1996-03-01

Full Text Available The lecture analyses the problem of development of the pipe conveyor with a rubber belt, the facitities of its application in the practice and environmental aspects resulting from its application. The pipe conveyor is a new perspective transport system. It enables ransporting bulk materials (coal, crushed, rock, coke, plant ash, fertilisers, limestones, time in a specific operations (power plants, heating plants.cellulose, salt, sugar, wheat and other materials with a minimum effect on the environment. The transported material is enclosed in the pipeline so that there is no escape of dust, smell or of the transported material itself. The lecture is aimed at: - the short description of the operating principle and design of the pipe conveyor which was developed in the firm Matador Púchov in cooperation with the firm TEDO, - the analysis of experiencie in working some pipe conveyors which were under operation for a certain

Preferred design of transfer points

Energy Technology Data Exchange (ETDEWEB)

Firstbrook, J

1983-06-01

The paper reports the results of a study carried out at MRDE on the performance of transfer points. These sites still require a considerable deployment of manpower. The investigations were divided into 3 main sections: mineral handling; chute design; belt cleaning and spillage conveying. In order to achieve a sufficient level of reliability of a transfer system, it is considered that the coal size should not be greater than 250 mm. Different designs of gravity transfer chute were studied and 3 basic designs emerged as being effective : dump chute, curved site entry, and asymmetric side entry. Selection is dependent on conveyor sizes, speeds, and mineral throughput. Individual belt cleaners are not sufficient to clean belts carrying typical run-of-mine material: two cleaners followed by a set of squeeze rollers are recommended. Several designs of spillage conveyor were investigated; at the present time the electro/hydraulic type appears to be the most satisfactory.

Experiments in a flighted conveyor comparing shear rates in compressed versus free surface flows

Science.gov (United States)

Pohlman, Nicholas; Higgins, Hannah; Krupiarz, Kamila; O'Connor, Ryan

2017-11-01

Uniformity of granular flow rate is critical in industry. Experiments in a flighted conveyor system aim to fill a gap in knowledge of achieving steady mass flow rate by correlating velocity profile data with mass flow rate measurements. High speed images were collected for uniformly-shaped particles in a bottom-driven flow conveyor belt system from which the velocity profiles can be generated. The correlation of mass flow rates from the velocity profiles to the time-dependent mass measurements will determine energy dissipation rates as a function of operating conditions. The velocity profiles as a function of the size of the particles, speed of the belt, and outlet size, will be compared to shear rate relationships found in past experiments that focused on gravity-driven systems. The dimension of the linear shear and type of decaying transition to the stationary bed may appear different due to the compression versus dilation space in open flows. The application of this research can serve to validate simulations in discrete element modeling and physically demonstrate a process that can be further developed and customized for industry applications, such as feeding a biomass conversion reactor. Sponsored by NIU's Office of Student Engagement and Experiential Learning.

Online X-ray Fluorescence (XRF) Analysis of Heavy Metals in Pulverized Coal on a Conveyor Belt.

Science.gov (United States)

Yan, Zhang; XinLei, Zhang; WenBao, Jia; Qing, Shan; YongSheng, Ling; DaQian, Hei; Da, Chen

2016-02-01

Heavy metals in haze episode will continue to threaten the quality of public health around the world. In order to decrease the emission of heavy metals produced from coal burning, an online X-ray fluorescence (XRF) analyzer system, consisting of an XRF analyzer with data acquisition software and a laser rangefinder, was developed to carry out the measurement of heavy metals in pulverized coal. The XRF analyzer was mounted on a sled, which can effectively smooth the surface of pulverized coal and reduce the impact of surface roughness during online measurement. The laser rangefinder was mounted over the sled for measuring the distance between a pulverized coal sample and the analyzer. Several heavy metals and other elements in pulverized coal were online measured by the XRF analyzer directly above a conveyor belt. The limits of detection for Hg, Pb, Cr, Ti, Fe, and Ca by the analyzer were 44 ± 2, 34 ± 2, 17 ± 3, 41 ± 4, 19 ± 3, and 65 ± 2 mg·kg(-1), respectively. The relative standard deviation (%RSD) for the elements mentioned was less than 7.74%. By comparison with the results by inductively-coupled plasma mass spectrometry (ICP-MS), relative deviation (%D) of the online XRF analyzer was less than 10% for Cr, Ti, and Ca, in the range of 0.8-24.26% for Fe, and greater than 20% for Hg and Pb. © The Author(s) 2016.

Assessment of statistical uncertainty in the quantitative analysis of solid samples in motion using laser-induced breakdown spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Cabalin, L.M.; Gonzalez, A. [Department of Analytical Chemistry, University of Malaga, E-29071 Malaga (Spain); Ruiz, J. [Department of Applied Physics I, University of Malaga, E-29071 Malaga (Spain); Laserna, J.J., E-mail: laserna@uma.e [Department of Analytical Chemistry, University of Malaga, E-29071 Malaga (Spain)

2010-08-15

Statistical uncertainty in the quantitative analysis of solid samples in motion by laser-induced breakdown spectroscopy (LIBS) has been assessed. For this purpose, a LIBS demonstrator was designed and constructed in our laboratory. The LIBS system consisted of a laboratory-scale conveyor belt, a compact optical module and a Nd:YAG laser operating at 532 nm. The speed of the conveyor belt was variable and could be adjusted up to a maximum speed of 2 m s{sup -1}. Statistical uncertainty in the analytical measurements was estimated in terms of precision (reproducibility and repeatability) and accuracy. The results obtained by LIBS on shredded scrap samples under real conditions have demonstrated that the analytical precision and accuracy of LIBS is dependent on the sample geometry, position on the conveyor belt and surface cleanliness. Flat, relatively clean scrap samples exhibited acceptable reproducibility and repeatability; by contrast, samples with an irregular shape or a dirty surface exhibited a poor relative standard deviation.

Assessment of statistical uncertainty in the quantitative analysis of solid samples in motion using laser-induced breakdown spectroscopy

Science.gov (United States)

Cabalín, L. M.; González, A.; Ruiz, J.; Laserna, J. J.

2010-08-01

Statistical uncertainty in the quantitative analysis of solid samples in motion by laser-induced breakdown spectroscopy (LIBS) has been assessed. For this purpose, a LIBS demonstrator was designed and constructed in our laboratory. The LIBS system consisted of a laboratory-scale conveyor belt, a compact optical module and a Nd:YAG laser operating at 532 nm. The speed of the conveyor belt was variable and could be adjusted up to a maximum speed of 2 m s - 1 . Statistical uncertainty in the analytical measurements was estimated in terms of precision (reproducibility and repeatability) and accuracy. The results obtained by LIBS on shredded scrap samples under real conditions have demonstrated that the analytical precision and accuracy of LIBS is dependent on the sample geometry, position on the conveyor belt and surface cleanliness. Flat, relatively clean scrap samples exhibited acceptable reproducibility and repeatability; by contrast, samples with an irregular shape or a dirty surface exhibited a poor relative standard deviation.

Assessment of statistical uncertainty in the quantitative analysis of solid samples in motion using laser-induced breakdown spectroscopy

International Nuclear Information System (INIS)

Cabalin, L.M.; Gonzalez, A.; Ruiz, J.; Laserna, J.J.

2010-01-01

Statistical uncertainty in the quantitative analysis of solid samples in motion by laser-induced breakdown spectroscopy (LIBS) has been assessed. For this purpose, a LIBS demonstrator was designed and constructed in our laboratory. The LIBS system consisted of a laboratory-scale conveyor belt, a compact optical module and a Nd:YAG laser operating at 532 nm. The speed of the conveyor belt was variable and could be adjusted up to a maximum speed of 2 m s -1 . Statistical uncertainty in the analytical measurements was estimated in terms of precision (reproducibility and repeatability) and accuracy. The results obtained by LIBS on shredded scrap samples under real conditions have demonstrated that the analytical precision and accuracy of LIBS is dependent on the sample geometry, position on the conveyor belt and surface cleanliness. Flat, relatively clean scrap samples exhibited acceptable reproducibility and repeatability; by contrast, samples with an irregular shape or a dirty surface exhibited a poor relative standard deviation.

Number of conveyor belts optimization regarding to its type and logistical parameters in mining industry

Directory of Open Access Journals (Sweden)

Dušan Malindžák

2008-12-01

Full Text Available Material transportation by belt conveyers is widely used in many industrial branches including mining plants. Belt conveyingdevelopment during the last year was oriented mainly on construction of belts. The consequence of this is the improvement of itsmanufacture qualities bringing down the costs for their exchange and maintenance.Despite the fact that there are some theoreticalcalculations based on a standards it is common in the industry that the belt is not properly selected or it is overdesigned or number of itstypes is too large what can lead to increased costs for its storage. The paper describes the optimization of number of belt types in miningcompany SIDERIT, s. r. o. Nižná Slaná by the method of modernization and unification of belts under practical skills and projectingbased on theoretical calculations.

Fracture behavior of rubber powder modified rubber blends applied for conveying belt top covers

OpenAIRE

Euchler, Eric; Stocek, Radek; Gehde, Michael; Bunzel, Jörg-Michael; Saal, Wolfgang; Kipscholl, Reinhold

2016-01-01

The aim of this study is concentrated on the experimental investigation of wear resistance of rubber powder modified rubber blends. Styrene-Butadiene-Rubber (SBR) blends applied for conveying belt top covers have been modified by ground rubber (rubber powder) based on SBR. We theoretically described the rubber wear mechanism due to loading conditions occurring at conveyor belts in the field, to simulate wear behavior of top cover rubber materials. An own developed testing equipment based on g...

Noise Properties of CMOS Current Conveyors

DEFF Research Database (Denmark)

Bruun, Erik

1996-01-01

The definition of the current conveyor is presented and it is shown how different generations of current conveyors can all be combined into a single definition of a multiple-output second generation current conveyor (CCII). Next, noise sources are introduced into the model, and a general noise...

Angular mining conveyor

Energy Technology Data Exchange (ETDEWEB)

Sender, A; Mura, A; Liduchowski, L; Zok, P; Skolik, W; Szyngiel, S; Rojek, H; Gajda, B; Major, M; Stanislawski, P; Sliwiok, H; Sikora, J

1988-10-19

Angular mining conveyor provided with a drag chain extending along the axis of its path of movement, and a corner member, inside which the drag chain is led in a forced way, characterized in that the drag chain, where its path curves around the corner member, is located by supporting of the vertical links of the chain along the required curved section of the conveyor path around said corner member, and the supporting line of the links is so chosen, that, within the said curved section of the conveyor path, a space is maintained between the vertical end surface of the scrapers and the outer curved surface of the radially inner side wall of a corner trough associated with the corner member, through which corner trough the scrapers pass. 10 figs.

Analysis of the Noise Characteristics of CMOS Current Conveyors

DEFF Research Database (Denmark)

Bruun, Erik

1997-01-01

The definition of the current conveyor is reviewed and a multiple-output second generation current conveyor (CCII) is shown to combine the different generations of current conveyors presently existing. Next, noise sources are introduced, and a general noise model for the current conveyor is descr......The definition of the current conveyor is reviewed and a multiple-output second generation current conveyor (CCII) is shown to combine the different generations of current conveyors presently existing. Next, noise sources are introduced, and a general noise model for the current conveyor...

Testing the feasibility of using a conveyor belt to load weanling and nursery pigs for transportation

Science.gov (United States)

Transportation is known to be a multi-faceted stressor, with the process of loading being one of the most significant factors impacting the stress to which animals are exposed. This project was designed to determine if using a conveyor to load pigs into the top deck of a simulated straight deck trai...

9 CFR 3.92 - Handling.

Science.gov (United States)

2010-01-01

... nonhuman primate must not be placed on unattended conveyor belts or on elevated conveyor belts, such as baggage claim conveyor belts and inclined conveyor ramps that lead to baggage claim areas, at any time... if an attendant is present at each end of the conveyor belt. (2) A primary enclosure containing a...

Design Study of an Incinerator Ash Conveyor Counting System - 13323

International Nuclear Information System (INIS)

Jaederstroem, Henrik; Bronson, Frazier

2013-01-01

A design study has been performed for a system that should measure the Cs-137 activity in ash from an incinerator. Radioactive ash, expected to consist of both Cs-134 and Cs-137, will be transported on a conveyor belt at 0.1 m/s. The objective of the counting system is to determine the Cs-137 activity and direct the ash to the correct stream after a diverter. The decision levels are ranging from 8000 to 400000 Bq/kg and the decision error should be as low as possible. The decision error depends on the total measurement uncertainty which depends on the counting statistics and the uncertainty in the efficiency of the geometry. For the low activity decision it is necessary to know the efficiency to be able to determine if the signal from the Cs-137 is above the minimum detectable activity and that it generates enough counts to reach the desired precision. For the higher activity decision the uncertainty of the efficiency needs to be understood to minimize decision errors. The total efficiency of the detector is needed to be able to determine if the detector will be able operate at the count rate at the highest expected activity. The design study that is presented in this paper describes how the objectives of the monitoring systems were obtained, the choice of detector was made and how ISOCS (In Situ Object Counting System) mathematical modeling was used to calculate the efficiency. The ISOCS uncertainty estimator (IUE) was used to determine which parameters of the ash was important to know accurately in order to minimize the uncertainty of the efficiency. The examined parameters include the height of the ash on the conveyor belt, the matrix composition and density and relative efficiency of the detector. (authors)

Design Study of an Incinerator Ash Conveyor Counting System - 13323

Energy Technology Data Exchange (ETDEWEB)

Jaederstroem, Henrik; Bronson, Frazier [Canberra Industries Inc., 800 Research Parkway Meriden CT 06450 (United States)

2013-07-01

A design study has been performed for a system that should measure the Cs-137 activity in ash from an incinerator. Radioactive ash, expected to consist of both Cs-134 and Cs-137, will be transported on a conveyor belt at 0.1 m/s. The objective of the counting system is to determine the Cs-137 activity and direct the ash to the correct stream after a diverter. The decision levels are ranging from 8000 to 400000 Bq/kg and the decision error should be as low as possible. The decision error depends on the total measurement uncertainty which depends on the counting statistics and the uncertainty in the efficiency of the geometry. For the low activity decision it is necessary to know the efficiency to be able to determine if the signal from the Cs-137 is above the minimum detectable activity and that it generates enough counts to reach the desired precision. For the higher activity decision the uncertainty of the efficiency needs to be understood to minimize decision errors. The total efficiency of the detector is needed to be able to determine if the detector will be able operate at the count rate at the highest expected activity. The design study that is presented in this paper describes how the objectives of the monitoring systems were obtained, the choice of detector was made and how ISOCS (In Situ Object Counting System) mathematical modeling was used to calculate the efficiency. The ISOCS uncertainty estimator (IUE) was used to determine which parameters of the ash was important to know accurately in order to minimize the uncertainty of the efficiency. The examined parameters include the height of the ash on the conveyor belt, the matrix composition and density and relative efficiency of the detector. (authors)

An under-belt capacitance and γ-ray backscatter gauge for on-line determination of moisture in coal

International Nuclear Information System (INIS)

Cutmore, N.G.; Roczniok, A.F.; Sowerby, B.D.

1987-01-01

A non-contacting under-belt capacitance and γ-ray backscatter technique has been developed for on-line measurement of moisture in coal. In this technique, moisture was correlated with radiofrequency susceptance and conductance, determined using an under-belt capacitance sensor in which a fringing electric field interrogates a layer of coal on the conveyor belt directly above the sensor. To compensate for variation in the density and thickness of the coal layer, an under-belt γ-ray backscatter gauge was used to measure an equivalent volume of coal. Laboratory measurements have shown that this technique compensates more accurately for density and thickness than does their direct physical measurement. (author)

Foerdervorrichtung zum geneigten oder senkrechten Foerdern von Stueckgut

OpenAIRE

Westermann, T.

1997-01-01

The first conveyor consists of a driven conveyor belt with tightener and pressure piece (4,5) pressing the conveyor belt (1), depending on the size of the piece of goods (13), against the second conveyor in the form of a fixed, inflexible wall slide plate (3). When the conveyor belt is placed against the fixed wall, an air gap (14) of between 5 and 10 millimetres long is formed between the two conveyors. Openings in the top and bottom of the conveyor arrangement, between the conveyor belt and...

Heavy rainfall in Mediterranean cyclones. Part I: contribution of deep convection and warm conveyor belt

Science.gov (United States)

Flaounas, Emmanouil; Kotroni, Vassiliki; Lagouvardos, Konstantinos; Gray, Suzanne L.; Rysman, Jean-François; Claud, Chantal

2018-04-01

In this study, we provide an insight to the role of deep convection (DC) and the warm conveyor belt (WCB) as leading processes to Mediterranean cyclones' heavy rainfall. To this end, we use reanalysis data, lighting and satellite observations to quantify the relative contribution of DC and the WCB to cyclone rainfall, as well as to analyse the spatial and temporal variability of these processes with respect to the cyclone centre and life cycle. Results for the period 2005-2015 show that the relationship between cyclone rainfall and intensity has high variability and demonstrate that even intense cyclones may produce low rainfall amounts. However, when considering rainfall averages for cyclone intensity bins, a linear relationship was found. We focus on the 500 most intense tracked cyclones (responsible for about 40-50% of the total 11-year Mediterranean rainfall) and distinguish between the ones producing high and low rainfall amounts. DC and the WCB are found to be the main cause of rainfall for the former (producing up to 70% of cyclone rainfall), while, for the latter, DC and the WCB play a secondary role (producing up to 50% of rainfall). Further analysis showed that rainfall due to DC tends to occur close to the cyclones' centre and to their eastern sides, while the WCBs tend to produce rainfall towards the northeast. In fact, about 30% of rainfall produced by DC overlaps with rainfall produced by WCBs but this represents only about 8% of rainfall produced by WCBs. This suggests that a considerable percentage of DC is associated with embedded convection in WCBs. Finally, DC was found to be able to produce higher rain rates than WCBs, exceeding 50 mm in 3-h accumulated rainfall compared to a maximum of the order of 40 mm for WCBs. Our results demonstrate in a climatological framework the relationship between cyclone intensity and processes that lead to heavy rainfall, one of the most prominent environmental risks in the Mediterranean. Therefore, we set

Selección de cadenas para equipos de transporte continuo. // Chain selection software for continuous conveyors.

Directory of Open Access Journals (Sweden)

F. Aguilar Parés

2003-01-01

ón, transportadores de tablillas, transportadores de rastrillos,elevadores de cangilones._____________________________________________________________________________Abstract:The design of conveyors and elevators that employ chains as driving member is commonly used in industry. An essentialelement for well functioning is the correct chain selection. There are a great variety of chains and attachments thataccomplish any requirements at manufacturers disposal. In order to supply these requirements there is a need to establish aprocedure that considers the following aspects:· Type of equipment (slat conveyor, flight conveyor, bucket conveyor, etc..· Transportation requirements (capacity, transportation velocity, material characteristics, etc..· Transportation conditions (overload, operation conditions, explotation time, etc..The resulting procedure is very annoying because there are stages in which a decision implies accommodation to latecalculations and as usual there is more than one solution. Therefore the SELCAD computation program is conceived for theuse by non experts in design and selection of continuous conveyors equipments. The program use data base from Link BeltIndustrial Chain Division catalog in which 14 types of chains are appraise with an average of 15 models for each and morethan 40 different attachments. Some of the program characteristics are:· User friendly environment (Visual Basic programation, version 5.· Help available at any moment.· Point out the characteristics of both driving member and gear.· Allows visualization of the selected real chain shape and attachment by photos.· Quick analysis of different variations.Key words: Transportation chain, slat conveyors, flight conveyor, bucket conveyor.

On-conveyor belt analysis of coal

Energy Technology Data Exchange (ETDEWEB)

Cheryl Lim; David Abernethy; S. Rainey; L.K. Noack [CSIRO Minerals (Australia)

2007-09-15

The report describes the design and plant-testing of a prototype commercial on-belt ash analyser at the Bengalla CHPP (Muswellbrook, NSW). This analyser uses the Neutron Inelastic Scatter (NIS) and Thermal Neutron Capture (TNC) Analysis (NITA) technique, which has been investigated extensively in earlier ACARP projects C5051 (laboratory feasibility study) and the previous stage of C9042 (development and lab testing of a field prototype and evaluate the suitability of the technique for specific energy and sulphur measurement). The NITA analyser has been demonstrated to be capable of achieving an accuracy of 0.46 %ash. Specifically, a measured value for total r.m.s. error of 0.77 %ash, measured r.m.s error includes various uncertainties (estimated to be 0.61 %ash) associated with the chemical analysis and sample collection procedures used to generate the chemical laboratory data provided for calibration. In earlier laboratory work it was demonstrated that a measured r.m.s error of 0.75 %ash corresponded to an actual accuracy of 0.53 %ash after much smaller laboratory sampling errors had been excluded. Accurate measurement of ash value can be achieved in material which is expected to have significant variability in mineralogy, and in the past has not been amenable to analysis using the DUET technique. Accurate measurement of ash value is possible in the presence of significant levels of segregation and changes in mineral matter composition. CSIRO is collaborating with a commercial partner to demonstrate and complete the implementation of the NITA technology in industry. A commercial prototype analyser (NITA II) is under development and a plant installation is expected to occur in mid 2008.

30 CFR 14.2 - Definitions.

Science.gov (United States)

2010-07-01

... MINING PRODUCTS REQUIREMENTS FOR THE APPROVAL OF FLAME-RESISTANT CONVEYOR BELTS General Provisions § 14.2... manufactures or controls the production of a conveyor belt and applies to MSHA for approval of conveyor belt... conveyor belt as approved. Extension of approval. A document issued by MSHA, which states that a change to...

Walking-Beam Solar-Cell Conveyor

Science.gov (United States)

Feder, H.; Frasch, W.

1982-01-01

Microprocessor-controlled walking-beam conveyor moves cells between work stations in automated assembly line. Conveyor has arm at each work station. In unison arms pick up all solar cells and advance them one station; then beam retracks to be in position for next step. Microprocessor sets beam stroke, speed, and position.

Universal Voltage Conveyor and Current Conveyor in Fast Full-Wave Rectifier

Directory of Open Access Journals (Sweden)

Josef Burian

2012-12-01

Full Text Available This paper deals about the design of a fast voltage-mode full-wave rectifier, where universal voltage conveyor and second-generation current conveyor are used as active elements. Thanks to the active elements, the input and output impedance of the non-linear circuit is infinitely high respectively zero in theory. For the rectification only two diodes and three resistors are required as passive elements. The performance of the circuit is shown on experimental measurement results showing the dynamic range, time response, frequency dependent DC transient value and RMS error for different values of input voltage amplitudes.

30 CFR 75.1101-5 - Installation of foam generator systems.

Science.gov (United States)

2010-07-01

... discharge foam to the belt drive, belt takeup, electrical controls, gear reducing unit and the conveyor belt..., electrical controls, gear reducing unit, and the conveyor belt over a distance of 50 feet; and, (2) At... electrical controls, gear reducing unit, and the conveyor belt over a distance of 150 feet. (c) The foam...

30 CFR 14.10 - Post-approval product audit.

Science.gov (United States)

2010-07-01

..., AND APPROVAL OF MINING PRODUCTS REQUIREMENTS FOR THE APPROVAL OF FLAME-RESISTANT CONVEYOR BELTS General Provisions § 14.10 Post-approval product audit. (a) Approved conveyor belts will be subject to... based. MSHA will select an approved conveyor belt to be audited; the selected belt will be...

Pickering irradiated fuel transfer conveyor isolation

Energy Technology Data Exchange (ETDEWEB)

Koivisto, D J; Eijsermans, L J [Atomic Energy of Canada Ltd., Mississauga, ON (Canada)

1997-12-31

Pickering A NGS has been in operation for 25 years and is one of the longest in service CANDU stations. Some underwater fuel handling equipment, notably the conveyor stops, have been without maintenance throughout that time. This paper describes the concept of a conveyor isolation system that permits draining of a single or multiple elevator columns and also the early stages of a development program for the elastomeric sealing element. The prototype seal element has been proven in lab tests to be capable of limiting leakage to 0.5 IGPM (imperial gallons per minute) at the design pressure of 6.5 psi. The design of a sealing element is particularly interesting because the conveyor tube is a square cross-section which contains an additional obstruction , a conveyor drive cable. A seal delivery, actuating and positioning system has been conceptually laid out and the design is proceeding, with projected implementation in 1998. (author). 8 figs.

Pickering irradiated fuel transfer conveyor isolation

International Nuclear Information System (INIS)

Koivisto, D.J.; Eijsermans, L.J.

1996-01-01

Pickering A NGS has been in operation for 25 years and is one of the longest in service CANDU stations. Some underwater fuel handling equipment, notably the conveyor stops, have been without maintenance throughout that time. This paper describes the concept of a conveyor isolation system that permits draining of a single or multiple elevator columns and also the early stages of a development program for the elastomeric sealing element. The prototype seal element has been proven in lab tests to be capable of limiting leakage to 0.5 IGPM (imperial gallons per minute) at the design pressure of 6.5 psi. The design of a sealing element is particularly interesting because the conveyor tube is a square cross-section which contains an additional obstruction , a conveyor drive cable. A seal delivery, actuating and positioning system has been conceptually laid out and the design is proceeding, with projected implementation in 1998. (author). 8 figs

Dust control at Yucca Mountain project

International Nuclear Information System (INIS)

Kissell, F.; Jurani, R.; Dresel, R.; Reaux, C.

1999-01-01

This report describes actions taken to control silica dust at the Yucca Mountain Exploratory Studies Facility, a tunnel located in Southern Nevada that is part of a scientific program to determine site suitability for a potential nuclear waste repository. The rock is a volcanic tuff containing significant percentages of both quartz and cristobalite. Water use for dust control was limited because of scientific test requirements, and this limitation made dust control a difficult task. Results are reported for two drifts, called the Main Loop Drift and the Cross Drift. In the Main Loop Drift, dust surveys and tracer gas tests indicated that air leakage from the TBM head, the primary ventilation duct, and movement of the conveyor belt were all significant sources of dust. Conventional dust control approaches yielded no significant reductions in dust levels. A novel alternative was to install an air cleaning station on a rear deck of the TBM trailing gear. It filtered dust from the contaminated intake air and discharged clean air towards the front of the TBM. The practical effect was to produce dust levels below the exposure limit for all TBM locations except close to the head. In the Cross Drift, better ventilation and an extra set of dust seals on the TBM served to cut down the leakage of dust from the TBM cutter head. However, the conveyor belt was much dustier than the belt in the main loop drift. The problem originated with dirt on the bottom of the belt return side and much spillage from the belt top side. Achieving lower dust levels in hard rock tunneling operations will require new approaches as well as a more meticulous application of existing technology. Planning for dust control will require specific means to deal with dust that leaks from the TBM head, dust that originates with leaky ventilation systems, and dust that comes from conveyor belts. Also, the application of water could be more efficient if automatic controls were used to adjust the water flow

Development of a mobile cord-monitoring unit (CMU) for steel cord conveyor belts of RWE Power AG; Entwicklung einer mobilen Zugtraeger-Ueberwachungs-Einrichtung (ZTUe) an Stahlseilfoerdergurten der RWE Power AG

Energy Technology Data Exchange (ETDEWEB)

Ebel, Max-Peter Benjamin [RWE Power AG, Technikzentrum Tagebau, Frechen (Germany)

2009-07-15

We have succeeded in developing a mobile measuring system suitable for everyday use that has already proven its practical suitability in a wide range of measurements. At present, we are preparing the stationary and permanent installation of aluminium supporting beams in the various conveyor drive stations. Thus, outages for the temporary installation of the supporting beam, which were still few, would no longer be required and the ''measuring crew'' would only have to carry around the handy measurement case and laptop. This considerably simpler application and the positive feedback on the benefits of the system are the main reasons why we will not work on the development of a stationary online system. The remaining additional benefit of such a unit would only be of minor significance. We are currently planning the following additional development steps as far as the ''mobile cord-monitoring unit'' is concerned: Developing a sensor-based belt edge monitoring unit as a modular complement to the system. This unit will monitor both belt edges by means of sensors, record them in the measuring signal and represent them explicitly in the evaluation. Linking the CMU evaluation software with the RegGEA system mentioned in Chapter 7, which has been introduced at RWE Power. This step combines an advanced central maintenance and planning system with an innovative belt damage detection system in a single piece of peripheral equipment, which offers the user much more advantages than the sum of the two individual systems taken alone would have done. Designing an aluminium supporting beam divisible into individual segments. Its handy pallet dimensions will allow the complete system to be transported to any site outside of RWE Power. Even though the system was originally conceived as a development for RWE Power, it has already met with great interest outside of RWE Power AG. (orig.)

30 CFR 14.4 - Application procedures and requirements.

Science.gov (United States)

2010-07-01

..., EVALUATION, AND APPROVAL OF MINING PRODUCTS REQUIREMENTS FOR THE APPROVAL OF FLAME-RESISTANT CONVEYOR BELTS... conveyor belt for use in underground coal mines must include the information below, except any information...) A technical description of the conveyor belt, which includes: (i) Trade name or identification...

Jim Walter Resources installs new overland conveyor

Energy Technology Data Exchange (ETDEWEB)

Fiscor, S.

2008-12-15

Embarking on a major expansion plan, the company is constructing a new additional overland conveyor coal to a recently refurbished prep plant. Jim Walter Resources recently invested $20 million in a new 5-mile overland conveyor system to haul coal from the No.7 deep coal mine in Alabama to the No.5 coal preparation plant. The size of the No.7 mine was effectively doubled. The article describes how this expansion move was decided upon and describes the design and installation of the new conveyor which spans approximately 5 miles. 4 photos.

Toxic effect of volatile products of thermooxidizing decomposition of conveyor belts

Energy Technology Data Exchange (ETDEWEB)

Faff, J.; Dudkiewicz, J.; Kauczak, M.; Waniewski, E.; Tokarzewski, E.

1985-01-01

Toxic effects of thermo-oxidizing decomposition products of conveying belts made of PVC and rubber have been tested. The resultant smokes were passed through a protective absorber. During 14-days' post-exposure observation, an increased activity of asparagine, aminotransferase and in some animal alanine aminotransferase was found. Moderately increased pathomorphological changes were found in lungs (emphysema, oedema interstitial and bronchogenic inflammations), along with slight degenerative changes in the liver and kidneys. In the peripheral blood, increased amounts of erythrocytes and leukocytes were found.

40 CFR 63.7143 - What definitions apply to this subpart?

Science.gov (United States)

2010-07-01

... material is transferred to or from a belt conveyor. Vent means an opening through which there is... filter bag or other malfunction and sound an alarm. Belt conveyor means a conveying device that... another location within a plant. Conveying systems include but are not limited to feeders, belt conveyors...

78 FR 69135 - Petitions for Modification of Application of Existing Mandatory Safety Standards

Science.gov (United States)

2013-11-18

... systems installed at conveyor belt drives. The petitioner states that: (1) A person trained in the testing... the deluge fire suppression systems installed at conveyor belt drives. The petitioner states that: (1... conveyor belt drives. The petitioner states that: (1) A person trained in the testing procedures specific...

20 CFR 655.520 - Special provisions regarding automated vessels.

Science.gov (United States)

2010-04-01

... longshore work consisting of the use of automated self-unloading conveyor belt or vacuum-actuated systems on... use of automated self-unloading conveyor belt or vacuum-actuated equipment at the particular port...-unloading conveyor belt or vacuum-actuated systems on a vessel is the prevailing practice at a particular...

30 CFR 14.7 - Approval marking and distribution records.

Science.gov (United States)

2010-07-01

..., EVALUATION, AND APPROVAL OF MINING PRODUCTS REQUIREMENTS FOR THE APPROVAL OF FLAME-RESISTANT CONVEYOR BELTS General Provisions § 14.7 Approval marking and distribution records. (a) An approved conveyor belt must be marketed only under the name specified in the approval. (b) Approved conveyor belt must be legibly and...

30 CFR 14.11 - Revocation.

Science.gov (United States)

2010-07-01

... MINING PRODUCTS REQUIREMENTS FOR THE APPROVAL OF FLAME-RESISTANT CONVEYOR BELTS General Provisions § 14.11 Revocation. (a) MSHA may revoke for cause an approval issued under this Part if the conveyor belt... a conveyor belt poses an imminent danger to the safety or health of miners, an approval may be...

Belt conveyor

OpenAIRE

Hoferek, Tomáš

2016-01-01

Tato bakalářská práce se zabývá problematikou pásového dopravníku pro přepravu suchého písku. Cílem práce je provést konstrukční řešení pásového dopravníku podle zadaných parametrů, kterými jsou dopravní výkon 100 000 kg.h-1, výškový rozdíl 5 m a vzdálenost mezi osami bubnů 40 m. Práce obsahuje krátký popis pásového dopravníku a jeho hlavních částí, funkční výpočet dle platné normy ČSN ISO 5048 a volbu jednotlivých komponentů z firemních katalogů. Dále také návrh napínacího zařízení, návrh po...

Luggage truck

NARCIS (Netherlands)

Oosterhuis, E.J.; Luttekes, E.; Rijsenbrij, J.C.

2004-01-01

The present invention relates to a luggage truck (2) comprising a loading space for luggage and provided with a conveyor belt (14) disposed in the loading space for the supply and removal of luggage, which conveyor belt is at the same time a storage unit for the luggage, wherein the conveyor belts

Trial Application of Pulse-Field Magnetization to Magnetically Levitated Conveyor System

Directory of Open Access Journals (Sweden)

Yoshihito Miyatake

2012-01-01

Full Text Available Magnetically levitated conveyor system using superconductors is discussed. The system is composed of a levitated conveyor, magnetic rails, a linear induction motor, and some power supplies. In the paper, pulse-field magnetization is applied to the system. Then, the levitation height and the dynamics of the conveyor are controlled. The static and dynamic characteristics of the levitated conveyor are discussed.

30 CFR 14.8 - Quality assurance.

Science.gov (United States)

2010-07-01

... MINING PRODUCTS REQUIREMENTS FOR THE APPROVAL OF FLAME-RESISTANT CONVEYOR BELTS General Provisions § 14.8... order to assure that the finished conveyor belt will meet the flame-resistance test— (1) Flame test a sample of each batch, lot, or slab of conveyor belts; or (2) Flame test or inspect a sample of each batch...

Designing a system for measuring the flow of material transported on belts using ultrasonic sensors

Science.gov (United States)

Mihuţ, N. M.

2015-11-01

Excavation tailings (scraping) and extracting the useful (lignite) in surface mine pits in Mining Basin Oltenia is achieved with technological lines of excavation - transport - dump of high productivity. A correlation of working capacity of the main components of technological lines (motor rotor, high capacity transport, car dumps) is necessary for economic reasons on electricity consumption. To achieve experience in the process was chosen excavator SRS 1400 from South Jilt career in the CET Turceni. The question of coal excavated volume has a great importance in the mine pits. At the excavation is desired a density estimate for each machine production tracking, cost estimation and tracking product unit profitability of each band on various sections zones. Permanent display size excavated volume snapshots in the excavator's cabin permits to track tape loading, eliminating unproductive times and information management to determine profitability. Another important requirement is closing the loop of the machine drive system of an excavator for a uniform deposition of carbon on the strip, thus achieving automatic control of the loading belt. Such equipment is important for the system dispatching in surface mine pits. Through a system of three ultrasound transducers to determine the smart instant of coal excavated section which, coupled with the tape speed, integrated over time will determine the amount of excavated coal. The basis of the system developed is a device for determining the volume and quantity of coal excavated acting on the march and optimize the system speed excavator working order. The device is designed primarily following the careers of lignite production: rotor excavators, rubber conveyor belts and dump facilities. Newly developed system aims to achieve the following determines: the optimum energy excavation depending on the nature of excavated material - lignite, shale, clay, etc., economic times to use the excavator bucket teeth rotor, energy

Modelling mechanical properties of the multilayer composite materials with the polyamide core

Directory of Open Access Journals (Sweden)

Talaśka Krzysztof

2018-01-01

Full Text Available Due to the wide range of application for belt conveyors, engineers look for many different combinations of mechanical properties of conveyor and transmission belts. It can be made by creating multilayer or fibre reinforced composite materials from base thermoplastic or thermosetting polymers. In order to gain high strength with proper elasticity and friction coefficient, the core of the composite conveyor belt is made of polyamide film core, which can be combined with various types of polymer fabrics, films or even rubbers. In this paper authors show the complex model of multilayer composite belt with the polyamide core, which can be used in simulation analyses. The following model was derived based on the experimental research, which consisted of tensile, compression and shearing tests. In order to achieve the most accurate model, proper simulations in ABAQUS were made and then the results were compared with empirical mechanical characteristics of a conveyor belt. The main goal of this research is to fully describe the perforation process of conveyor and transmission belts for vacuum belt conveyors. The following model will help to develop design briefs for machines used for mechanical perforation.

Development of a completely decentralized control system for modular continuous conveyors

OpenAIRE

Mayer, Stephan H.

2009-01-01

To increase the flexibility of application of continuous conveyor systems, a completely decentralized control system for a modular conveyor system is introduced in the paper. This system is able to carry conveyor units without any centralized infrastructure. Based on existing methods of decentralized data transfer in IT networks, single modules operate autonomously and, after being positioned into the required topology, independently connect together to become a functioning conveyor system.

7 CFR 58.228 - Dump hoppers, screens, mixers and conveyors.

Science.gov (United States)

2010-01-01

... Service 1 Equipment and Utensils § 58.228 Dump hoppers, screens, mixers and conveyors. The product contact surfaces of dump hoppers, screens, mixers and conveyors which are used in the process of transferring dry... 7 Agriculture 3 2010-01-01 2010-01-01 false Dump hoppers, screens, mixers and conveyors. 58.228...

Conveyor system bolt failure analysis

International Nuclear Information System (INIS)

McCutcheon, S.H.; Waaser, R.E.

1981-07-01

The Savannah River Plant (SRP) is operated for the U.S. Department of Energy (DOE) by E.I. du Pont de Nemours and Co. Reactors at SRP are used to produce nuclear isotopes for national defense. As part of the routine operation of each of the reactors, irradiated fuel assemblies are remotely discharged from the reactor, transferred in air, and placed underwater in a Deposit and Exit (D and E) canal. The D and E conveyor transports the assemblies under the reactor room wall into the disassembly basin, where they are stored for several months before shipment to the separations areas. On August 13, 1980, a broken bolt was discovered on the D and E conveyor during a routine pre-operational inspection. The failed bolt was one of four which anchor a bearing on one of the conveyor drive shafts. All four of the bolts on the affected bearing were replaced as an immediate corrective measure and the discharge of irradiated fuel assemblies was subsequently completed without difficulty

Baseline restoration using current conveyors

International Nuclear Information System (INIS)

Morgado, A.M.L.S.; Simoes, J.B.; Correia, C.M.

1996-01-01

A good performance of high resolution nuclear spectrometry systems, at high pulse rates, demands restoration of baseline between pulses, in order to remove rate dependent baseline shifts. This restoration is performed by circuits named baseline restorers (BLRs) which also remove low frequency noise, such as power supply hum and detector microphonics. This paper presents simple circuits for baseline restoration based on a commercial current conveyor (CCII01). Tests were performed, on two circuits, with periodic trapezoidal shaped pulses in order to measure the baseline restoration for several pulse rates and restorer duty cycles. For the current conveyor based Robinson restorer, the peak shift was less than 10 mV, for duty cycles up to 60%, at high pulse rates. Duty cycles up to 80% were also tested, being the maximum peak shift 21 mV. The peak shift for the current conveyor based Grubic restorer was also measured. The maximum value found was 30 mV at 82% duty cycle. Keeping the duty cycle below 60% improves greatly the restorer performance. The ability of both baseline restorer architectures to reject low frequency modulation is also measured, with good results on both circuits

ABOUT TECHNOLOGY FEATURES OF ASSEMBLING OF RUBBER-METAL CONNECTIONS

Directory of Open Access Journals (Sweden)

VODOLAZSKAYA Nataliia

2016-11-01

Full Text Available Assembly process is important technological operation when manufacturing products and equipment, and also it uses during operation and repairs different type of implements The modern automated manufacture cannot be presented without the existence of machines continuously action, in particular of belt conveyors. One of its basic units is the belt and ways of its connection. Usually, the quantity of cracks of belt joints is equal to (reaches 62 within 1 km of a belt of conveyor during 10 years upon condition that equipment works in a difficult cycle of mines. One of the basic operation problems of these transports is the rupture of the joint of a belt as emergency idle times of conveyors makes approximately of 10 % of working hours, and planned stops on manufacturing or repair of joints - to of 20 %. Therefore, now research in the field of maintenance of qualitative manufacturing of a joint of conveyor belts are of interest at this time. The way of using of rubber-metal connections assembling with help self-cutting screws is offered. This allows increasing durability’s characteristics of joints of the conveyor belt

30 CFR 75.333 - Ventilation controls.

Science.gov (United States)

2010-07-01

...; (2) To separate belt conveyor haulageways from return air courses, except where belt entries in areas of mines developed before March 30, 1970, are used as return air courses; (3) To separate belt... point of travel of the dolly or 600 feet from the point of deepest penetration in the conveyor belt...

3D MODELING OF DRIVE SHAFT OF A MONORAIL CONVEYOR

Directory of Open Access Journals (Sweden)

STĂNĂŞEL Iulian

2016-11-01

Full Text Available The conveyors are used to transport various products in successive steps until they reach their destination and to ensure cargo volumes to balance the flow buffer. The conveyors monorail type are used for the transfer of the products, piece by piece and they can be suspended and can operate at heights and different tasks. In this paper is presented a method for the design of the drive shaft of a monorail conveyor, by using CAD-CAE applications.

30 CFR 77.400 - Mechanical equipment guards.

Science.gov (United States)

2010-07-01

... shall be guarded. (b) Overhead belts shall be guarded if the whipping action from a broken line would be hazardous to persons below. (c) Guards at conveyor-drive, conveyor-head, and conveyor-tail pulleys shall... between the belt and the pulley. (d) Except when testing the machinery, guards shall be securely in place...

An integrated multi-criteria decision-making methodology for conveyor system selection

Directory of Open Access Journals (Sweden)

Pairat Jiamruangjarus

2016-12-01

Full Text Available Material handling equipment (MHE is important for every industry because it has an effect on the productivity of manufacturing. Conveyor systems are presently one popular type of MHE. This paper presents an integration of the analytic network process (ANP with the benefits, opportunities, costs and risk (BOCR model in order to select the best conveyor system. The proposed model established a network with four merits, six strategies criteria, and twenty six sub-criteria with four alternatives (present, roller conveyor, chain conveyor, and monorail. The ANP is to determine the relative weights of an evaluative criteria and decision alternatives. Therefore, the final ranking of the alternatives are calculated by synthesizing the score of each alternative under BOCR. The results showed that the best alternative under all five methods is the chain conveyor. These research results can be easily applied, adapted and used to improve performance of selecting the conveyer system in small and medium enterprises through large industries.

The need for sustainable technology diffusion in mining: Achieving the use of belt conveyor systems in the German hard-rock quarrying industry

Directory of Open Access Journals (Sweden)

Tobias Braun

2017-01-01

Full Text Available The movement of raw materials can be one of the most challenging tasks in open pit mining, with truck transportation representing the largest factor in mining costs and resulting in major greenhouse gas (GHG emissions. In this study, the transportation methods of bulk materials within German hard-rock open pit mines were investigated. Approximately 450 quarries were studied for their production tonnage, lease areas, mined rock type as well as mining methods and processing equipment. The results demonstrate that 90% of the operations use truck-based transportation methods, with the remainder relying partly or completely on continuous conveyor-based systems. The installation of continuous conveyors compared to trucks represents a real alternative because of reduced dead load, reduced GHG emissions and in many cases even reduced costs. Thus, for in-pit haulage in quarries sustainable technology substitutions exist that are yet to be adopted by the German quarrying industry. As this study shows, in the future the diffusion of sustainable technologies requires site champions and large-scale case studies that demonstrate their successful introduction in the mining value chain.

30 CFR 14.5 - Test samples.

Science.gov (United States)

2010-07-01

... MINING PRODUCTS REQUIREMENTS FOR THE APPROVAL OF FLAME-RESISTANT CONVEYOR BELTS General Provisions § 14.5 Test samples. Upon request by MSHA, the applicant must submit 3 precut, unrolled, flat conveyor belt...

Shear Roll Mill Reactivation

Science.gov (United States)

2012-09-13

pneumatically operated paste dumper and belt conveyor system, the loss in weight feeder system, the hydraulically operated shear roll mill, the pellet...out feed belt conveyor , and the pack out system comprised of the metal detector, scale, and pack out empty and full drum roller conveyors . Page | 4...feed hopper and conveyor supplying the loss in weight feeder were turned on, and it was verified that these items functioned as designed . The

the screw-conveyor vane design for piece-wise construction

African Journals Online (AJOL)

Dr Obe

Summary. One of the long-used methods of conveying granular, Powdery or slurry material is by the screw conveyor. This method of transport is well suited to some at the needs of local processing Industries based on such local produce as millet, maize, cocoa-beans, rice, palm-kernels. The spiral vanes of such conveyors ...

Solvent minimization induces preferential orientation and crystal clustering in serial micro-crystallography on micro-meshes, in situ plates and on a movable crystal conveyor belt.

Science.gov (United States)

Soares, Alexei S; Mullen, Jeffrey D; Parekh, Ruchi M; McCarthy, Grace S; Roessler, Christian G; Jackimowicz, Rick; Skinner, John M; Orville, Allen M; Allaire, Marc; Sweet, Robert M

2014-11-01

X-ray diffraction data were obtained at the National Synchrotron Light Source from insulin and lysozyme crystals that were densely deposited on three types of surfaces suitable for serial micro-crystallography: MiTeGen MicroMeshes™, Greiner Bio-One Ltd in situ micro-plates, and a moving kapton crystal conveyor belt that is used to deliver crystals directly into the X-ray beam. 6° wedges of data were taken from ∼100 crystals mounted on each material, and these individual data sets were merged to form nine complete data sets (six from insulin crystals and three from lysozyme crystals). Insulin crystals have a parallelepiped habit with an extended flat face that preferentially aligned with the mounting surfaces, impacting the data collection strategy and the design of the serial crystallography apparatus. Lysozyme crystals had a cuboidal habit and showed no preferential orientation. Preferential orientation occluded regions of reciprocal space when the X-ray beam was incident normal to the data-collection medium surface, requiring a second pass of data collection with the apparatus inclined away from the orthogonal. In addition, crystals measuring less than 20 µm were observed to clump together into clusters of crystals. Clustering required that the X-ray beam be adjusted to match the crystal size to prevent overlapping diffraction patterns. No additional problems were encountered with the serial crystallography strategy of combining small randomly oriented wedges of data from a large number of specimens. High-quality data able to support a realistic molecular replacement solution were readily obtained from both crystal types using all three serial crystallography strategies.

Water: The conveyor belt for sustainable livelihoods and economic development

Science.gov (United States)

Mapani, Benjamin; Meck, Maideyi; Makurira, Hodson; Magole, Lapologang; Mashauri, Damas; mazvimavi, Dominic; Mul, Marloes

2016-04-01

The theme for the 2014 symposium focused on the contribution of integrated water resources management (IWRM) to socio-economic development. A number of papers presented various methods that could be used to enable society to access clean water; sanitation and provision of water for rainfed and irrigation based agriculture and aquaculture. Water is the engine of development, that drives both money generating ventures as well as activities which cannot be assigned exact monetary value, but are essential for the social and economic well being of communities. It is now accepted that in order to produce most products, the contribution of water has to be factored in; from manufacturing to mining. The role that water plays in the has a much higher economic value than most people realize.

Piezoelectric Driving of Vibration Conveyors: An Experimental Assessment

Directory of Open Access Journals (Sweden)

Emerson Bastos de Albuquerque

2013-07-01

Full Text Available Vibratory feeders or vibratory conveyors have been widely used for the transport and orientation of individual parts and bulk materials in many branches of industrial activity. From the designer’s standpoint, the current endeavor is to conceive efficient vibratory feeders, satisfying constraints of power consumption, vibration transmission and noise emission. Moreover, the interest in the reduction of maintenance cost is always present. In this context, this paper investigates experimentally the concept of vibratory conveying based on the use of piezoelectric materials for motion generation. A small-size prototype of a linear conveyor, in which lead-zirconate-titanate (PZT patches are bonded to the resilient elements, is described. One of the main design goals is that the prototype is intended to be fed directly from the electric network, aiming at avoiding the use of electronic equipment for driving. To comply with this feature and, at the same time, enable to adjust the transport velocity, a mechanical device has been conceived in such a way that the first natural frequency of the conveyor can be changed. It is shown that the transport velocity is determined by the proximity between the excitation frequency and the first natural frequency of the conveyor. The experimental tests performed to characterize the dynamic behavior of the prototype are described and the range of transport velocities is determined.

Piezoelectric Driving of Vibration Conveyors: An Experimental Assessment

Science.gov (United States)

Rade, Domingos Alves; de Albuquerque, Emerson Bastos; Figueira, Leandro Chaves; Carvalho, João Carlos Mendes

2013-01-01

Vibratory feeders or vibratory conveyors have been widely used for the transport and orientation of individual parts and bulk materials in many branches of industrial activity. From the designer's standpoint, the current endeavor is to conceive efficient vibratory feeders, satisfying constraints of power consumption, vibration transmission and noise emission. Moreover, the interest in the reduction of maintenance cost is always present. In this context, this paper investigates experimentally the concept of vibratory conveying based on the use of piezoelectric materials for motion generation. A small-size prototype of a linear conveyor, in which lead-zirconate-titanate (PZT) patches are bonded to the resilient elements, is described. One of the main design goals is that the prototype is intended to be fed directly from the electric network, aiming at avoiding the use of electronic equipment for driving. To comply with this feature and, at the same time, enable to adjust the transport velocity, a mechanical device has been conceived in such a way that the first natural frequency of the conveyor can be changed. It is shown that the transport velocity is determined by the proximity between the excitation frequency and the first natural frequency of the conveyor. The experimental tests performed to characterize the dynamic behavior of the prototype are described and the range of transport velocities is determined. PMID:23867743

Ore sorting using natural gamma radiation

International Nuclear Information System (INIS)

Clark, G.J.; Dickson, B.L.; Gray, F.E.

1980-01-01

A method of sorting an ore which emits natural gamma radiation is described, comprising the steps of: (a) mining the ore, (b) placing, substantially at the mining location, the sampled or mined ore on to a moving conveyor belt, (c) measuring the natural gamma emission, water content and mass of the ore while the ore is on the conveyor belt, (d) using the gamma, water content and mass measurements to determine the ore grade, and (e) directing the ore to a location characteristic of its grade when it leaves the conveyor belt

On Dynamic Range Limitations of CMOS Current Conveyors

DEFF Research Database (Denmark)

Bruun, Erik

1999-01-01

frequency band and for the situation where the conveyor is used over the full bandwidth achievable. Finally, the optimisation of the current input range is related to the distortion characteristics and it is pointed out that to a first order approximation the distortion is independent of the current range.......This paper is concerned with the dynamic range of continuous time CMOS current mode circuits. As a representative current mode device a class AB current conveyor is examined. First, the voltage input range of the high impedance Y input is investigated. Next, the current input range of the low...... impedance X input is investigated. It is compared to the thermal noise in the X to Z signal path in order to evaluate the dynamic range, and the dependencies of the dynamic range on the supply voltage and the transistor lay-out is derived, both for the situation where the conveyor is used over a narrow...

Traction calculation of band conveyors using the ''Nairi-2'' computer

Energy Technology Data Exchange (ETDEWEB)

Kutlunin, V A; Livshis, A V; Pod' yemshchikov, A N

1982-01-01

An algorithm is described and a program is introduced for traction calculation of band conveyors using the ''Nairi-2'' computer. The calculation system of the conveyor is derived by means of dividing the closed loop of the band into straight sections, which are separated by drums. The number of sections depends on the number of drums, the bypass system of them by the band, the shape of the conveyor route and in each specific case, a specific number is chosen. The initial information for the computer is assigned by a matrix, each row of which consists of parameters of the corresponding section. As a result, the forces of the beginning and end of the sections are found, and the required output of the drive motors with observance of the conditions of non-slippage of the drive drums and limiting of the maximum slack of the band between rollers are also found. The program allows one to make traction calculations of band conveyors with any routing shape for any number and position of the drive drums.

Novel apparatus permitting the recovery of polluting products such as hydrocarbons and fuel oil spilled onto the surface of the water

Energy Technology Data Exchange (ETDEWEB)

1979-01-26

This apparatus for the recovery of oil spills consists of a chassis equipped at both ends with drums rotating and carrying a closed loop of a conveyor belt made of a sponge-like or foam-like absorbing substance which resists the effect of hydrocarbons, oils, oxidants and alkaline materials, while its water absorption power is practically zero. This material is glued or cast on a fabric core or on a large mesh material. A cleaning drum associated with the belt compresses the belt and causes the polluting material to be squeezed into a vat. The chassis is mounted on a ship with shallow draft or on an amphibious vehicle. This apparatus is applicable to all cases where a polluting product spilled onto the surface of the water must be eliminated.

40 CFR 49.24 - Federal Implementation Plan Provisions for Navajo Generating Station, Navajo Nation.

Science.gov (United States)

2010-07-01

... crusher, any conveyor belt transfer point, any pneumatic material transferring, any baghouse or other..., grinding mill, screening operation, belt conveyor, truck loading or unloading operation, or railcar..., and the owner or operator uses best efforts regarding planning, design, and operating procedures to...

On aspects of vibration of axially moving continua

NARCIS (Netherlands)

Hageraats-Ponomareva, S.

2009-01-01

In axially moving structures like conveyor belt systems, magnetic tapes, and so on, vibrations occur due to the presence of different kinds of imperfections in the systems. For these structures internal resonances can lead to severe vibrations. Resonance free conveyor belt systems can be constructed

75 FR 10174 - Source-Specific Federal Implementation Plan for Navajo Generating Station; Navajo Nation

Science.gov (United States)

2010-03-05

..., any conveyor belt transfer point, any pneumatic material transferring, any baghouse or other control... than 20% from any crusher, grinding mill, screening operation, belt conveyor, truck loading or... emissions from this facility. This will be an ongoing process designed to incorporate suitable VCS as they...

Accelerated Comparative Fatigue Strength Testing of Belt Adhesive Joints

Science.gov (United States)

Bajda, Miroslaw; Blazej, Ryszard; Jurdziak, Leszek

2017-12-01

Belt joints are the weakest link in the serial structure that creates an endless loop of spliced belt segments. This affects not only the lower strength of adhesive joints of textile belts in comparison to vulcanized splices, but also the replacement of traditional glues to more ecological but with other strength parameters. This is reflected in the lowered durability of adhesive joints, which in underground coal mines is nearly twice shorter than the operating time of belts. Vulcanized splices require high precision in performance, they need long time to achieve cross-linking of the friction mixture and, above all, they require specialized equipment (vulcanization press) which is not readily available and often takes much time to be delivered down, which means reduced mining output or even downtime. All this reduces the reliability and durability of adhesive joints. In addition, due to the consolidation on the Polish coal market, mines are joined into large economic units serviced by a smaller number of processing plants. The consequence is to extend the transport routes downstream and increase reliability requirements. The greater number of conveyors in the chain reduces reliability of supply and increases production losses. With high fixed costs of underground mines, the reduction in mining output is reflected in the increase in unit costs, and this at low coal prices on the market can mean substantial losses for mines. The paper describes the comparative study of fatigue strength of shortened samples of adhesive joints conducted to compare many different variants of joints (various adhesives and materials). Shortened samples were exposed to accelerated fatigue in the usually long-lasting dynamic studies, allowing more variants to be tested at the same time. High correlation between the results obtained for shortened (100 mm) and traditional full-length (3×250 mm) samples renders accelerated tests possible.

VIRTUAL MODEL OF A ROLLER CONVEYOR INTEGRATED INTO A LOGISTIC FLOW

Directory of Open Access Journals (Sweden)

POPESCU Adrian

2015-11-01

Full Text Available In this article is presented, with the help of graphics, a logistic flow for palletizing and wrapping operations. The loaded pallets are transported by means of a roller conveyor. Creating the virtual model for the conveyer allows us to emphasize the compatibility elements between on the one hand the mechanical assemblies of the flow components and on the other hand the subassemblies of the conveyer structure. The paper has focused on the presentation of the conveyor specific assembly and how are placed the sensors on the mechanical structure of the conveyor. Finally, the main working phases are graphically presented within the flow, highlighting the loaded pallet positions in the flow.

Study and modeling of changes in volumetric efficiency of helix conveyors at different rotational speeds and inclination angels by ANFIS and statistical methods

Directory of Open Access Journals (Sweden)

A Zareei

2017-05-01

Full Text Available Introduction Spiral conveyors effectively carry solid masses as free or partly free flow of materials. They create good throughput and they are the perfect solution to solve the problems of transport, due to their simple structure, high efficiency and low maintenance costs. This study aims to investigate the performance characteristics of conveyors as function of auger diameter, rotational speed and handling inclination angle. The performance characteristic was investigated according to volumetric efficiency. In another words, the purpose of this study was obtaining a suitable model for volumetric efficiency changes of steep auger to transfer agricultural products. Three different diameters of auger, five levels of rotational speed and three slope angles were used to investigate the effects of changes in these parameters on volumetric efficiency of auger. The used method is novel in this area and the results show that performance by ANFIS models is much better than common statistical models. Materials and Methods The experiments were conducted in Department of Mechanical Engineering of Agricultural Machinery in Urmia University. In this study, SAYOS cultivar of wheat was used. This cultivar of wheat had hard seeds and the humidity was 12% (based on wet. Before testing, all foreign material was separated from the wheat such as stone, dust, plant residues and green seeds. Bulk density of wheat was 790 kg m-3. The auger shaft of the spiral conveyor was received its rotational force through belt and electric motor and its rotation leading to transfer the product to the output. In this study, three conveyors at diameters of 13, 17.5, and 22.5 cm, five levels of rotational speed at 100, 200, 300, 400, and 500 rpm and three handling angles of 10, 20, and 30º were tested. Adaptive Nero-fuzzy inference system (ANFIS is the combination of fuzzy systems and artificial neural network, so it has both benefits. This system is useful to solve the complex non

30 CFR 75.1311 - Transporting explosives and detonators.

Science.gov (United States)

2010-07-01

... noncombustible materials. (c) When explosives and detonators are transported on conveyor belts— (1) Containers of... explosives or detonators, a person shall be at each transfer point between belts and at the unloading location; and (4) Conveyor belts shall be stopped before explosives or detonators are loaded or unloaded...

30 CFR 18.48 - Circuit-interrupting devices.

Science.gov (United States)

2010-07-01

... energized. (f) Belt conveyors shall be equipped with control switches to automatically stop the driving motor in the event the belt is stopped, or abnormally slowed down. Note: Short transfer-type conveyors... Design Requirements § 18.48 Circuit-interrupting devices. (a) Each machine shall be equipped with a...

Solvent minimization induces preferential orientation and crystal clustering in serial micro-crystallography on micro-meshes, in situ plates and on a movable crystal conveyor belt

Energy Technology Data Exchange (ETDEWEB)

Soares, Alexei S., E-mail: soares@bnl.gov [Brookhaven National Laboratory, Upton, NY 11973 (United States); Mullen, Jeffrey D. [Brookhaven National Laboratory, Upton, NY 11973 (United States); University of Oregon, Eugene, OR 97403-1274 (United States); Parekh, Ruchi M. [Brookhaven National Laboratory, Upton, NY 11973 (United States); Suffolk County Community College, Selden, NY 11784 (United States); McCarthy, Grace S.; Roessler, Christian G.; Jackimowicz, Rick; Skinner, John M. [Brookhaven National Laboratory, Upton, NY 11973 (United States); Orville, Allen M. [Brookhaven National Laboratory, Upton, NY 11973 (United States); Brookhaven National Laboratory, Upton, NY 11973 (United States); Allaire, Marc [Brookhaven National Laboratory, Upton, NY 11973 (United States); Sweet, Robert M. [Brookhaven National Laboratory, Upton, NY 11973 (United States); Brookhaven National Laboratory, Upton, NY 11973 (United States)

2014-10-09

Strategies are described for optimizing the signal-to-noise of diffraction data, and for combining data from multiple crystals. One challenge that must be overcome is the non-random orientation of crystals with respect to one another and with respect to the surface that supports them. X-ray diffraction data were obtained at the National Synchrotron Light Source from insulin and lysozyme crystals that were densely deposited on three types of surfaces suitable for serial micro-crystallography: MiTeGen MicroMeshes™, Greiner Bio-One Ltd in situ micro-plates, and a moving kapton crystal conveyor belt that is used to deliver crystals directly into the X-ray beam. 6° wedges of data were taken from ∼100 crystals mounted on each material, and these individual data sets were merged to form nine complete data sets (six from insulin crystals and three from lysozyme crystals). Insulin crystals have a parallelepiped habit with an extended flat face that preferentially aligned with the mounting surfaces, impacting the data collection strategy and the design of the serial crystallography apparatus. Lysozyme crystals had a cuboidal habit and showed no preferential orientation. Preferential orientation occluded regions of reciprocal space when the X-ray beam was incident normal to the data-collection medium surface, requiring a second pass of data collection with the apparatus inclined away from the orthogonal. In addition, crystals measuring less than 20 µm were observed to clump together into clusters of crystals. Clustering required that the X-ray beam be adjusted to match the crystal size to prevent overlapping diffraction patterns. No additional problems were encountered with the serial crystallography strategy of combining small randomly oriented wedges of data from a large number of specimens. High-quality data able to support a realistic molecular replacement solution were readily obtained from both crystal types using all three serial crystallography strategies.

Solvent minimization induces preferential orientation and crystal clustering in serial micro-crystallography on micro-meshes, in situ plates and on a movable crystal conveyor belt

International Nuclear Information System (INIS)

Soares, Alexei S.; Mullen, Jeffrey D.; Parekh, Ruchi M.; McCarthy, Grace S.; Roessler, Christian G.; Jackimowicz, Rick; Skinner, John M.; Orville, Allen M.; Allaire, Marc; Sweet, Robert M.

2014-01-01

Strategies are described for optimizing the signal-to-noise of diffraction data, and for combining data from multiple crystals. One challenge that must be overcome is the non-random orientation of crystals with respect to one another and with respect to the surface that supports them. X-ray diffraction data were obtained at the National Synchrotron Light Source from insulin and lysozyme crystals that were densely deposited on three types of surfaces suitable for serial micro-crystallography: MiTeGen MicroMeshes™, Greiner Bio-One Ltd in situ micro-plates, and a moving kapton crystal conveyor belt that is used to deliver crystals directly into the X-ray beam. 6° wedges of data were taken from ∼100 crystals mounted on each material, and these individual data sets were merged to form nine complete data sets (six from insulin crystals and three from lysozyme crystals). Insulin crystals have a parallelepiped habit with an extended flat face that preferentially aligned with the mounting surfaces, impacting the data collection strategy and the design of the serial crystallography apparatus. Lysozyme crystals had a cuboidal habit and showed no preferential orientation. Preferential orientation occluded regions of reciprocal space when the X-ray beam was incident normal to the data-collection medium surface, requiring a second pass of data collection with the apparatus inclined away from the orthogonal. In addition, crystals measuring less than 20 µm were observed to clump together into clusters of crystals. Clustering required that the X-ray beam be adjusted to match the crystal size to prevent overlapping diffraction patterns. No additional problems were encountered with the serial crystallography strategy of combining small randomly oriented wedges of data from a large number of specimens. High-quality data able to support a realistic molecular replacement solution were readily obtained from both crystal types using all three serial crystallography strategies

78 FR 59066 - Petitions for Modification of Application of Existing Mandatory Safety Standards

Science.gov (United States)

2013-09-25

... thirty (30) sprays along each of approximately ten primary belt-conveyor drives and an average of sixty... using the hand-loading method. (8) Belt conveyor haulage is not used in this underground mine for...-loading mining methods. (3) Development above the active gangway is designed to mine into the level above...

The fluid–solid coupling analysis of screw conveyor in drilling fluid centrifuge based on ANSYS

Directory of Open Access Journals (Sweden)

Hongbin Liu

2015-09-01

Full Text Available In the centrifugal separations of drilling fluid, screw conveyor is a critical component to push and separate the sediment. The work performance and structural parameters of conveyor are immediately related to the production capability, the working life and the separating effect of the centrifuge. The existing researches always use the theoretical calculation of the approximate loads to analyze the strength of conveyor, and it cannot reflect the stress situations accurately. In order to ensure the precise mastery of the working performance, this article obtained pressure distribution under working conditions from CFX evaluation and gained equivalent stress and deformation under several load conditions by using the ANSYS Workbench platform to check the strength of conveyor. The results showed that the influence of centrifugal hydraulic pressure was less than that of centrifugal force on the strength and deformation of conveyor. Besides, the maximum equivalent stress occurred at the inside of the feed opening, while the maximum deformation occurred at the conveyor blade edge of taper extremity. Furthermore, whether considered the feed opening or not, the computing model had a great influence on the analysis results, and the simplified loads had a great influence on the deformation analysis results. The methods and results from this article can provide reference for the design and the improvement of screw conveyor.

Teleconnections from Tropics to Northern Extratropics through a Southerly Conveyor

OpenAIRE

Wang, Zhuo; Chang, C.-P.; Wang, Bin; Jin, Fei-fei

2005-01-01

Rossby wave propagation theory predicts that Rossby waves in a tropical easterly flow cannot escape from the Tropics to the extratropics. Here the authors show that a southerly flow component in the basic state (a southerly conveyor) may transfer a Rossby wave source northward; thus, a forcing embedded in the deep tropical easterlies may excite a Rossby wave response in the extratropical westerlies. It is shown that the southerly conveyor determines the location of the effective R...

20 CFR 655.500 - Purpose, procedure and applicability of subparts F and G of this part.

Science.gov (United States)

2010-04-01

... automated self-unloading conveyor belt or vacuum-actuated system on a vessel and the Administrator has not... of the use of an automated self-unloading conveyor belt or vacuum-actuated system on a vessel. The...) The use of alien crewmembers is not during a strike or lockout nor designed to influence the election...

Isotope weigher with scintillation detector in transmission geometry

International Nuclear Information System (INIS)

Machaj, B.; Antoniak, W.

1976-01-01

Measuring head of isotope conveyor belt weigher contains gamma radiation source 137 Cs or 60 Co having activity less than 5 mCi, long plastic scintillator as a radiation detector and tachometer as a belt speed sensor. Measurement of instantaneous belt loading is based on the principle of radiation attenuation in transmission geometry. Electronic signal originated by gamma radiation is first linearized and then multiplied by signal which is proportional to belt speed, thus giving at the multiplier output signal which is proportional to the mass being conveyed. Mass weighing accuracy is not worse than 2%. Belt width of conveyor belt 30 - 180 cm. (author)

How Selby coal will reach the surface

Energy Technology Data Exchange (ETDEWEB)

1979-11-01

In many respects this conveyor will exemplify the NCB's intention to employ the latest technology at Selby. This single conveyor will be almost 15km long, and will bring coal to the surface from almost 1 km below ground level. A steel cord belt, 1300 mm wide and weighing over 2500 tonnes, will travel at up to 8.4 m/s to bring as much as 3200 t/h of coal to the surface. The conveyor is capable of delivering up to 1800 t/h of coal even from the furthest and deepest point in the conveyor run. Maximum tension in the belt is almost 200 tonnes, and even on the slack side of the pulley, the tension will be 68 tonnes. Eleven bunkering points will each be capable of feeding 750 tonnes of coal per hour, and a computerized control will ensure that the required mix is brought from the bunkers without exceeding the maximum capacity of the conveyor. When maximum tonnage is not being handled, the conveyor will be capable of running at the lowest speed which is capable of bringing out the tonnage on the belt. This minimizes wear and tear on all moving parts of the system. From each bunkering point, the coal will be fed down a chute onto a short accelerating conveyor which feeds the coal centrally onto the main conveyor and ensures that it is moving in the same direction as the main conveyor.

ANALYSIS OF DESIGN PECULIARITIES PERTAINING TO DRUMS OF CONTINUOUS MACHINES

Directory of Open Access Journals (Sweden)

V. Yu. Prushak

2007-01-01

Full Text Available The paper considers design peculiarities of belt conveyor drums in respect of their operational reliability; their advantages and disadvantages have been analyzed. There are some proposals presenting technical solutions to modernization of belt conveyor drum designs which presuppose reduction of their material consumption while preserving their strength and general rigidity. 

Monitoring and evaluation of wire mesh forming life

Science.gov (United States)

Enemuoh, Emmanuel U.; Zhao, Ping; Kadlec, Alec

2018-03-01

Forming tables are used with stainless steel wire mesh conveyor belts to produce variety of products. The forming tables will typically run continuously for several days, with some hours of scheduled downtime for maintenance, cleaning and part replacement after several weeks of operation. The wire mesh conveyor belts show large variation in their remaining life due to associated variations in their nominal thicknesses. Currently the industry is dependent on seasoned operators to determine the replacement time for the wire mesh formers. The drawback of this approach is inconsistency in judgements made by different operators and lack of data knowledge that can be used to develop decision making system that will be more consistent with wire mesh life prediction and replacement time. In this study, diagnostic measurements about the health of wire mesh former is investigated and developed. The wire mesh quality characteristics considered are thermal measurement, tension property, gage thickness, and wire mesh wear. The results show that real time thermal sensor and wear measurements would provide suitable data for the estimation of wire mesh failure, therefore, can be used as a diagnostic parameter for developing structural health monitoring (SHM) system for stainless steel wire mesh formers.

Mining-induced fault reactivation associated with the main conveyor belt roadway and safety of the Barapukuria Coal Mine in Bangladesh: Constraints from BEM simulations

Energy Technology Data Exchange (ETDEWEB)

Islam, Md. Rafiqul; Shinjo, Ryuichi [Department of Physics and Earth Sciences, University of the Ryukyus, Okinawa, 903-0213 (Japan)

2009-09-01

Fault reactivation during underground mining is a critical problem in coal mines worldwide. This paper investigates the mining-induced reactivation of faults associated with the main conveyor belt roadway (CBR) of the Barapukuria Coal Mine in Bangladesh. The stress characteristics and deformation around the faults were investigated by boundary element method (BEM) numerical modeling. The model consists of a simple geometry with two faults (Fb and Fb1) near the CBR and the surrounding rock strata. A Mohr-Coulomb failure criterion with bulk rock properties is applied to analyze the stability and safety around the fault zones, as well as for the entire mining operation. The simulation results illustrate that the mining-induced redistribution of stresses causes significant deformation within and around the two faults. The horizontal and vertical stresses influence the faults, and higher stresses are concentrated near the ends of the two faults. Higher vertical tensional stress is prominent at the upper end of fault Fb. High deviatoric stress values that concentrated at the ends of faults Fb and Fb1 indicate the tendency towards block failure around the fault zones. The deviatoric stress patterns imply that the reinforcement strength to support the roof of the roadway should be greater than 55 MPa along the fault core zone, and should be more than 20 MPa adjacent to the damage zone of the fault. Failure trajectories that extend towards the roof and left side of fault Fb indicate that mining-induced reactivation of faults is not sufficient to generate water inflow into the mine. However, if movement of strata occurs along the fault planes due to regional earthquakes, and if the faults intersect the overlying Lower Dupi Tila aquiclude, then liquefaction could occur along the fault zones and enhance water inflow into the mine. The study also reveals that the hydraulic gradient and the general direction of groundwater flow are almost at right angles with the trends of

Comparison of a pneumatic conveyor and bucket elevator on an energy and economic basis

Energy Technology Data Exchange (ETDEWEB)

Rothwell, T.M.; Southwell, P.H. (Agricultural and Energy Engineering Ltd., Moorefield, ON (Canada)); Vigneault, C. (Agricultural Canada Research Station, St-Jean-sur-Richelieu, PQ (Canada))

1991-07-01

Tests were performed at a commercial feed mill which was replacing an existing pneumatic conveyor with a bucket elevator, in order to compare the performance of the two types of conveyor on an energy and cost basis. The conveyors were used to transport ground corn from a hammermill at an average grinding rate of 8.5 tonnes/h. At the same conveying rate of ground product, the pneumatic conveyor required a power of 27.5 kW and an energy of 4.77 kWh/tonne while the bucket elevator required a power of 4.7 kW and an energy of 0.88 kWh/tonne. The financial costs of conveying energy were $8,350/y for the pneumatic system and $1,540/y for the bucket elevator, excluding peak demand charges for electricity. The tests therefore demonstrated that a bucket elevator is far more efficient than a pneumatic conveyor and should be considered in the design of new feed mills. For existing mills, a bucket elevator should be considered if there are problems with the pneumatic system already in place or if the capacity of the mill needs to be increased. 2 refs., 2 tabs.

DESIGN AND IMPLEMENTATION OF CONVEYOR LINE SPEED ...

African Journals Online (AJOL)

DESIGN AND IMPLEMENTATION OF CONVEYOR LINE SPEED SYNCHRONISER FOR INDUSTRIAL CONTROL APPLICATIONS: A CASE STUDY OF ... in bottles.Therefore a Proportional Integral Derivative(PID) controller was designed to act as a speed synchronizer in order to eliminate the above mentioned problems.

City transport of the future - the high speed pedestrian conveyor. Part 2: ergonomic considerations of complete conveyor systems.

Science.gov (United States)

Browning, A C

1975-03-01

This is the second part of an article on an unusual form of passenger transport, the moving pavement or pedestrian conveyor running at speeds up to 16 km/h. Part 1, "Ergonomic considerations of acceleration, deceleration and transfer sections," was published in the December, 1974, issue.

Application of a cross-pit bridge conveyor system in mining

Energy Technology Data Exchange (ETDEWEB)

Zeindler, R.W. (Krupp Canada Inc., Calgary, Alberta); Fawcett, D.A.

1981-04-01

A summary is presented of the report completed by the Coal Mining Research Centre in 1980. This report was of a cross-pit conveyor system applied as an auxillary mining complement to the major stripping unit, a dragline. The purpose of the CMRC report was to evaluate selective mining and replacement of the upper horizons of the strata as an aid in reclamation. These strata were the topsoil, subsoil and glacial till. Past utilization of cross-pit conveyor systems and related engineering studies were assessed. The parameters of the study were based on the mining and geological conditions of the Alberta prairie coal mines. The principal excavator for stripping was a dragline. Excavation of the upper horizons was done by a bucket-wheel excavator discharging onto the cross-pit conveyor. Alternative equipment applications were economically compared. Four cases or geological sections were evaluated in detail. The economics of the alternative mining systems for each of the cases were determined. In all instances, the most economical solution was a tandem system utilizing a dragline with a bucket-wheel excavator/cross-pit conveyor system. For both the CMRC study and a similar US paper, the application of a tandem system provided the lowest annual ownership and operating costs. The tandem system consists of a dragline excavating and casting the majority of the waste or overburden and a BWE/CPCS selectively excavating and replacing the topsoil, subsoil and part of the unconsolidated overburden. The bridge spans and designs are within known technical and economic limits.

7 CFR 58.246 - Cleaning of dryers, collectors, conveyors, ducts, sifters and storage bins.

Science.gov (United States)

2010-01-01

... (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946 AND THE EGG... and the frequency of cleaning shall be based upon observation of actual operating results and...

EFFICIENCY INCREASING OF BELT CONVEYOR’S DRIVE BY CERAMIC LAGGING OF DRIVING PULLEY

Directory of Open Access Journals (Sweden)

Josef JURMAN

2012-04-01

Full Text Available In any point of the belt contact with the drum a relative speed compensation takes place that is carried out by a slippage even when the relevant contact spots are fairly clean and dry. This leads to heat generation that is being absorbed by both materials involved – by the belt as well as by the drum. Unlike the belt, the drum lagging would increase its temperature up to a certain limit that depends on number of factors. When the lagging surface temperature is reaching appx. 60°C some structural changes in the lagging material take place and further rise of temperature can create a risk of belt inflammation and destruction of the driving unit. This can be avoided by lagging the drum with new materials that eliminate any friction on the contact surfaces and that are heat resistant.

Simply Adjustable Sinusoidal Oscillator Based on Negative Three-Port Current Conveyors

Directory of Open Access Journals (Sweden)

R. Sotner

2010-09-01

Full Text Available The paper deals with sinusoidal oscillator employing two controlled second-generation negative-current conveyors and two capacitors. The proposed oscillator has a simple circuit configuration. Electronic (voltage adjusting of the oscillation frequency and condition of oscillation are possible. The presented circuit is verified in PSpice utilizing macro models of commercially available negative current conveyors. The circuit is also verified by experimental measurements. Important characteristics and drawbacks of the proposed circuit and influences of real active elements in the designed circuit are discussed in detail.

30 CFR 75.1722 - Mechanical equipment guards.

Science.gov (United States)

2010-07-01

... may cause injury to persons shall be guarded. (b) Guards at conveyor-drive, conveyor-head, and conveyor-tail pulleys shall extend a distance sufficient to prevent a person from reaching behind the guard and becoming caught between the belt and the pulley. (c) Except when testing the machinery, guards...

The study of thickness and density compensation of neutron-measuring moisture system on conveyor belt

International Nuclear Information System (INIS)

Jia Wenbao; Su Tongling; Zhang Xiaomin; Xu Zhongfeng

1999-01-01

The neutron-measuring transmission moisture system on the conveyer belt is systematically studied. A method of density and thickness compensation has been used to carryout the on-line measurements of the moisture of the unshaped, discontinuous and irregular moving matter. At the same time, the thickness weighed average method is employed to modify the prompt moisture at a fixed time, and to improve the accuracy of measuring the moisture. The experimental data show that the measurement errors are within ±2.5% when the thickness is between 2 cm and 16 cm and the water percentage is between 6% and 16%. The errors can reach 0.2% if thickness weighed average for moving matter lasts for a long time

Shiftable conveyor systems in open-cast mines in India

Energy Technology Data Exchange (ETDEWEB)

Noronha, H S; Patel, J C

1984-12-01

The materials handling and earthmoving arrangements are described at the Neyveli lignite mine in Tamil Nadu State, 200 km from Madras, India. The equipment used consists of shiftable conveyors, transfer feeders and drive stations.

Floating Inductance and FDNR Using Positive Polarity Current Conveyors

Directory of Open Access Journals (Sweden)

K. Pal

2004-01-01

Full Text Available A generalized circuit based on five positive polarity second-generation current conveyors is introduced. The circuit simulates a floating inductance, capacitor floatation circuit and floating fdnr. All these circuits use grounded capacitors.

30 CFR 56.9200 - Transporting persons.

Science.gov (United States)

2010-07-01

... hand without creating a hazard to persons; or (h) On conveyors unless the conveyors are designed to.... (1) This paragraph does not apply to car droppers if they are secured with safety belts and lines...

30 CFR 57.9200 - Transporting persons.

Science.gov (United States)

2010-07-01

... hand without creating a hazard to persons; or (h) On conveyors unless the conveyors are designed to.... (1) This paragraph does not apply to car droppers if they are secured with safety belts and lines...

A stitch in time

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-01-01

Belt-conveyor maintenance technology, developed for the mining and quarrying industry, has helped to boost productivity at Clydeport's Hunterston Terminal facility in Scotland. Hunterston's major function is to receive steam coal and send it back out by ship, rail and truck. Delays such as caused by a rip or break in a conveyor belt are heavily penalised. Hunterston has found that a heavy duty rivet-attached mechanical belt-clip, designed for mining, provides a fast emergency fix on some belts that are normally jointed by vulcanised splices. Known on the Flexco 'S' rivet-hinged fastener, it consists of top and bottom plates jointed at one end by two wide-hinge loops. 2 photos.

Voltage-Controlled Square/Triangular Wave Generator with Current Conveyors and Switching Diodes

Directory of Open Access Journals (Sweden)

Martin Janecek

2012-12-01

Full Text Available A novel relaxation oscillator based on integrating the diode-switched currents and Schmitt trigger is presented. It is derived from a known circuit with operational amplifiers where these active elements were replaced by current conveyors. The circuit employs only grounded resistances and capacitance and is suitable for high frequency square and triangular signal generation. Its frequency can be linearly and accurately controlled by voltage that is applied to a high-impedance input. Computer simulation with a model of a manufactured conveyor prototype verifies theoretic assumptions.

ANALISIS TOTAL PRODUCTIVE MAINTENANCE DENGAN METODE OVERALL EQUIPMENT EFFECTIVENESS DAN FUZZY FAILURE MODE AND EFFECTS ANALYSIS

Directory of Open Access Journals (Sweden)

Supriyadi Supriyadi

2017-11-01

Full Text Available Ash Handling System merupakan suatu bagian dari pembangkit listrik tenaga uap dengan bahan bakar batu bara yang berfungsi untuk menyalurkan limbah pembuangan sisa hasil proses pembakaran batu bara pada boiler. Sisa pembakaran terbagi menjadi fly ash dan bottom ash. Untuk sisa pembakaran fly ash akan disalurkan menuju ke Electrostatic Precipitator untuk ditangkap  dengan metode corona dan ditransfer menuju penampungan fly ash dengan cara dimampatkan bersama udara dari kompresor yang melalui pipa-pipa dan tabung transporter. Sedangkan untuk sisa pembakaran bottom ash akan disalurkan dengan alat yang disebut SSC (Submerged Scraper Conveyor. Gangguan pada SSC dapat terjadi mulai dari belt putus, masalah pada penggerak, hingga masalah pada kelistrikan dan instrumennya. Penelitian ini bertujuan untuk mengetahui nilai OEE, mengetahui dampak gangguan belt sobek, mengetahui penyebab terjadinya belt conveyor sobek dan melakukan estimasi hasil perbaikan dari sisi biaya. Penelitian ini menggunakan metode Overall Equipment Effectiveness (OEE dan Fuzzy Failure Mode and Effects Analysis. Hasil penelitian menunjukkan bahwa rata-rata nilai OEE pada tahun 2015 sekitar 52,05%, masih di bawah standar nilai OEE sebesar 85%. Penyebab utamanya adalah adanya gangguan belt sobek karena gesekan belt dengan support return ketika belt conveyor mengalami jogging yang berdampak pada terganggunya penyaluran abu. Modifikasi dapat menghindari kerugian perusahaan sebesar Rp. 582.548.800,00.

Universal method for opnimal design main structural assemblies of steel structures stationary conveyor with hanging ribbon

Directory of Open Access Journals (Sweden)

Boslovyak P.V.

2015-10-01

Full Text Available The technique and the detailed algorithm for optimal design of steel structures hospitaltion of the conveyor with hang-ing ribbon. Developed a universal objective function together with the system-limited-subject to limits of main components of steel structures of stationary conveyor with hanging ribbon.

Heavy Oil Recovery Ohmsett Test Report

Science.gov (United States)

2012-06-01

U.S. The first phase of separation is to refloat the oil for physical collection using a conveyor belt or rope mop oil skimmer. The open discharge is...inverted cone-shroud installed in the Frac tank for physical collection using a conveyor belt or rope mop oil skimmer. Heavy Oil Recovery Ohmsett Test...develop and test viable designs for systems which can detect and recover oil from subsurface environments. This is the second major report within this

Microfluidic magnetic bead conveyor belt

NARCIS (Netherlands)

van Pelt, S.; Frijns, A.J.H.; den Toonder, J.M.J.

2017-01-01

Magnetic beads play an important role in the miniaturization of clinical diagnostics systems. In lab-on-chip platforms, beads can be made to link to a target species and can then be used for the manipulation and detection of this species. Current bead actuation systems utilize complex on-chip coil

Conveyor with rotary airlock apparatus

Science.gov (United States)

Kronbert, J.W.

1993-01-01

This invention is comprised of an apparatus for transferring objects from a first region to a second region, the first and second regions having differing atmospheric environments. The apparatus includes a shell having an entrance and an exit, a conveyer belt running through the shell from the entrance to the exit, and a horizontally mounted `revolving door` with at least four vanes revolving about its axis. The inner surface of the shell and the top surface of the conveyer belt act as opposing walls of the `revolving door`. The conveyer belt dips as it passes under but against the revolving vanes so as not to interfere with them but to engage at least two of the vanes and define thereby a moving chamber. Preferably, the conveyer belt has ridges or grooves on its surface that engage the edges of the vanes and act to rotate the vane assembly. Conduits are provided that communicate with the interior of the shell and allow the adjustment of the atmosphere of the moving chamber or recovery of constituents of the atmosphere of the first region from the moving chamber before they escape to the second region.

On-line dry wood measurement in chips by nuclear means

International Nuclear Information System (INIS)

Oftedal, E.

1978-01-01

A system which has been installed and operating for two years in a Norwegian paper mill is described. It consists of a radiometric conveyor belt weighing instrument, a radiometric moisture guage and a data processor. The weighing instrument uses a cesium 137 source located above the conveyor belt with the radiation detector under the belt. The moisture gauge employs an americium-beryllium neutron source and a slow neutron detector, both placed above the belt. The data is processed and the moisture content calculated is continuously displayed. 4 analogue outputs are also available for automatic on-line process control. The results over a period of 20 months are shown, compared with results from laboratory measurements of samples. The two curves follow each other fairly closely. (JIW)

On-line analysis of hydrogen and other parameters in the mineral and energy industries

International Nuclear Information System (INIS)

Sowerby, B.D.

1998-01-01

The objective of the project is the development and industrial application of nuclear and microwave techniques for the on-line determination of hydrogen, moisture and other parameters. This document presents progress with respect to the stated objectives. A laboratory feasibility study has been carried out on new and advanced neutron and gamma ray analysis systems for the direct on-conveyor belt analysis of ash in coal. Neutron inelastic scattering and thermal neutron capture gamma ray technique were used in development of an on-belt elemental analyser for cement industry. Microwave based technology has been developed for on-conveyor belt determination of moisture in coal. A fast neutron and gamma-ray transmission technique has been applied for on-belt determination of moisture in lump coke

Feeder Type Optimisation for the Plain Flow Discharge Process of an Underground Hopper by Discrete Element Modelling

Directory of Open Access Journals (Sweden)

Jan Nečas

2017-09-01

Full Text Available This paper describes optimisation of a conveyor from an underground hopper intended for a coal transfer station. The original solution was designed with a chain conveyor encountered operational problems that have limited its continuous operation. The Discrete Element Modeling (DEM was chosen to optimise the transport. DEM simulations allow device design modifications directly in the 3D CAD model, and then the simulation makes it possible to evaluate whether the adjustment was successful. By simulating the initial state of coal extraction using a chain conveyor, trouble spots were identified that caused operational failures. The main problem has been the increased resistance during removal of material from the underground hopper. Revealed resistances against material movement were not considered in the original design at all. In the next step, structural modifications of problematic nodes were made. For example, the following changes have been made: reduction of storage space or installation of passive elements into the interior of the underground hopper. These modifications made were not effective enough, so the type of the conveyor was changed from a drag chain conveyor to a belt conveyor. The simulation of the material extraction using a belt conveyor showed a significant reduction in resistance parameters while maintaining the required transport performance.

Justification of process of loading coal onto face conveyors by auger heads of shearer-loader machines

Science.gov (United States)

Nguyen, K. L.; Gabov, V. V.; Zadkov, D. A.; Le, T. B.

2018-03-01

This paper analyzes the processes of removing coal from the area of its dislodging and loading the disintegrated mass onto face conveyors by auger heads of shearer-loader machines. The loading process is assumed to consist of four subprocesses: dislodging coal, removal of the disintegrated mass by auger blades from the crushing area, passive transportation of the disintegrated mass, and forming the load flow on the bearing surface of a face conveyor. Each of the considered subprocesses is different in its physical nature, the number of factors influencing it, and can be complex or multifactor. Possibilities of improving the efficiency of loading coal onto a face conveyor are addressed. The selected criteria of loading efficiency are load rate, specific energy consumption, and coal size reduction. Efficiency is improved by reducing the resistance to movement of the disintegrated mass during loading by increasing the area of the loading window section and the volume of the loading area on the conveyor, as well as by coordination of intensity of flows related to the considered processes in local areas.

On-stream analysis of iron ore and its potential for improving export quality control

International Nuclear Information System (INIS)

Holmes, R.J.

1988-01-01

An on-stream iron ore analyser has been developed in collaboration with Hamersley Iron Pty. Limited for determining the iron content of both lump (-30+6 mm particle size) and fines (-6 mm particle size) on conveyor belts. The analyser, which is called IRONSCAN, is based on pair production, and is now commercially available from Mineral Control Instrumentation Limited (MCI) in Adelaide. It can be mounted under existing conveyor belts with minimal modifications to the conveyor structure, and the presence of steel cables in the belt does not interfere once the analyser has been correctly calibrated. The analyser has been extensively tested on both lump and fines on the shiploading conveyor at Dampier, and typically the root mean square (r.m.s.) deviation between single IRONSCAN measurements and conventional chemical analyses is better than 0.5% Fe. It is currently being evaluated on - 150 mm ore from the primary crusher at Mount Tom Price, and initial results are encouraging. The principal advantage of IRONSCAN is that it provides rapid information on ore grades. But perhaps its greatest potential is at the primary crusher where conventional sampling and analysis is very expensive to implement. 11 figs., 1 tab

Design of conveyor utilization monitoring system: a case study of powder coating line in sheet metal fabrication

Science.gov (United States)

Prasetyo, Hoedi; Sugiarto, Yohanes; Nur Rosyidi, Cucuk

2018-03-01

Conveyor is a very useful equipment to replace manpower in transporting the goods. It highly influences the productivity, production capacity utilization and eventually the production cost. This paper proposes a system to monitor the utilization of conveyor at a low cost through a case study at powder coating process line in a sheet metal fabrication. Preliminary observation was conducted to identify the problems. The monitoring system was then built and executed. The system consists of two sub systems. First is sub system for collecting and transmitting the required data and the second is sub system for displaying the data. The system utilizes sensors, wireless data transfer and windows-based application. The test results showed that the whole system works properly. By this system, the productivity and status of the conveyor can be monitored in real time. This research enriches the development of conveyor monitoring system especially for implementation in small and medium enterprises.

Conceptual design of a conveyor system for the Philippine multipurpose cobalt-60 gamma irradiation facility

International Nuclear Information System (INIS)

Borras, A.M.

1992-01-01

The Multipurpose Cobalt-60 Gamma Irradiation Facility at the PNRI presently utilizes the batch irradiation method using turntables to rotate the product boxes. The target materials or products are being carried manually or with the use of pushcart through the personnel maze. This paper presents a conceptual design for the best suitable product-handling or conveyor system for the Philippine Multipurpose Cobalt-60 Gamma Irradiation Facility. The main irradiation conveyor line shall be a 55 cm x 200 cm slat-type conveyor made of SUS 304 material that could be operated in a semi-batch continuous flow and/or shuffle-dwell method with a tact-time range of 10 min to 7 h. The products can be irradiated in a single direction, two-pass, two-sided method. (auth.). 11 refs.; 4 figs.; 2 tabs

Current and Voltage Conveyors in Current- and Voltage-Mode Precision Full-Wave Rectifiers

Directory of Open Access Journals (Sweden)

J. Koton

2011-04-01

Full Text Available In this paper new versatile precision full-wave rectifiers using current and/or voltage conveyors as active elements and two diodes are presented. The performance of these circuit solutions is analysed and compared to the opamp based precision rectifier. To analyze the behavior of the functional blocks, the frequency dependent RMS error and DC transient value are evaluated for different values of input voltage amplitudes. Furthermore, experimental results are given that show the feasibilities of the conveyor based rectifiers superior to the corresponding operational amplifier based topology.

Dynamic analysis of scraper conveyor operation with external loads

Directory of Open Access Journals (Sweden)

Świder Jerzy

2017-01-01

Full Text Available A load to an armoured face conveyor (AFC during coal mining is changeable and very difficult or even impossible to be predicted. Changes of the load to the upper scraper chain affect the load of the driving motor and generate changes in a scraper chain tension. Impact of increasing the external load to the upper scraper chain on the operation of electric motors and on the scraper chain tension is presented. The developed numerical model of the Rybnik 850 conveyor enabled identifying the places of the scraper chain high tension or places of its loosening. An impact of changing frequency of driving motor voltage on AFC’s operational conditions was tested and analysed using the AFC’s numerical model. During tests, tension of the scraper chain on the discharge end and the return end was recorded. High tension of the scraper chain and its loosening during the changeable load were also recorded on upward and downward transportation of run-of-mine material.

30 CFR 75.1103-4 - Automatic fire sensor and warning device systems; installation; minimum requirements.

Science.gov (United States)

2010-07-01

... systems that use carbon monoxide sensors shall provide identification of fire along all belt conveyors. (1... downwind of each belt drive unit, each tailpiece transfer point, and each belt take-up. If the belt drive, tailpiece, and/or take-up for a single transfer point are installed together in the same air course, and the...

Design Considerations for CMOS Current Mode Operational Amplifiers and Current Conveyors

DEFF Research Database (Denmark)

Bruun, Erik

implementations of current mode opamps in CMOS technology are described. Also, current conveyor configurations with multiple outputs and flexible feedback connections from outputs to inputs are introduced. The dissertation includes several examples of circuit configurations ranging from simple class A and class......This dissertation is about CMOS current conveyors and current mode operational amplifiers (opamps). They are generic devices for continuous time signal processing in circuits and systems where signals are represented by currents.Substantial advancements are reported in the dissertation, both...... related to circuit implementations and system configurations and to an analysis of the fundamental limitations of the current mode technique.In the field of system configurations and circuit implementations different configurations of high gain current opamps are introduced and some of the first...

A Joint Positioning and Attitude Solving Method for Shearer and Scraper Conveyor under Complex Conditions

Directory of Open Access Journals (Sweden)

Jiacheng Xie

2017-01-01

Full Text Available In a fully mechanized coal-mining face, the positioning and attitude of the shearer and scraper conveyor are inaccurate. To overcome this problem, a joint positioning and attitude solving method that considers the effect of an uneven floor is proposed. In addition, the real-time connection and coupling relationship between the two devices is analyzed. Two types of sensors, namely, the tilt sensor and strapdown inertial navigation system (SINS, are used to measure the shearer body pitch angle and the scraper conveyor shape, respectively. To improve the accuracy, two pieces of information are fused using the adaptive information fusion algorithm. It is observed that, using a marking strategy, the shearer body pitch angle can be reversely mapped to the real-time shape of the scraper conveyor. Then, a virtual-reality (VR software that can visually simulate this entire operation process under different conditions is developed. Finally, experiments are conducted on a prototype experimental platform. The positioning error is found to be less than 0.38 times the middle trough length; moreover, no accumulated error is detected. This method can monitor the operation of the shearer and scraper conveyor in a highly dynamic and precise manner and provide strong technical support for safe and efficient operation of a fully mechanized coal-mining face.

Clostridium difficile in retail baskets, trolleys, conveyor belts, and plastic bags in Saudi Arabia.

Science.gov (United States)

Alqumber, Mohammed A

2014-10-01

To determine Clostridium difficile (C. difficile) prevalence on retail surfaces and shoppers plastic bags. From 20 June to 10 August 2011, in a cross-sectional epidemiological study, 17 supermarkets from 2 cities, Albaha and Altaif, Saudi Arabia were sampled. A total of 800 samples, which comprised 200 samples per surveyed surface, were studied. These included baskets, trolleys, conveyer belts, and outgoing shoppers' plastic bags. Clostridium difficile strains were isolated. The isolates were characterized using ribotyping and  polymerase chain reaction for the detection of toxin A (tcdA), toxin B (tcdB), binary toxin (cdtB), and toxin C (tcdC) genes. Susceptibility to antibiotics was determined on a Muller-Hinton agar with 5% sheep blood agar using E-tests. Overall, the C. difficile prevalence on sampled surfaces was 0.75%. The highest prevalence was found on retail baskets and trolleys, followed by plastic bags. A total of 5 different ribotypes were identified. Alterations in tcdC were detected in ribotype 027 and BT1. All the identified isolates were susceptible to vancomycin, but resistant to levofloxacin. In this study, C. difficile was present at a rate of 0.75% on supermarket surfaces. Spore disinfection of implicated surfaces may be necessary to control any community-acquired infections caused by this pathogen. 

Statistical mechanical characteristics of slip-ring induction motors when direct current braking

Energy Technology Data Exchange (ETDEWEB)

Kedzior, W; Muchorowski, J; Pienkowski, K

1980-09-01

This paper evaluates methods of braking high capacity belt conveyors used in brown coal surface mines in Poland. Complications associated with belt conveyor braking, particularly when a conveyor moves down a slope, are analyzed. A method of calculating mechanical characteristics of wound-rotor induction motors during direct current braking taking into account saturation of magnetic circuit is presented. Characteristics of the SZUr motor with 630 kW power, used in brown coal mining, are also given. Analyses show that motor operation can be efficiently braked in two ways: 1. by changing additional resistance in rotor circuit (e.g. using thyristor controller); 2. by changing intensity of electric current supplied to stator winding (e.g. using a rectifier). (3 refs.) (In Polish)

Chiral Rayleigh particles discrimination in dynamic dual optical traps

International Nuclear Information System (INIS)

Carretero, Luis; Acebal, Pablo; Blaya, Salvador

2017-01-01

Highlights: • A chiral optical conveyor belt for enantiomeric separation of nanopar-ticles is numerically demonstrated. • Chiral resolution has been theoretically analyzed for chiral spheres immersed in water. • Electromagnetic fields have been designed for obtaining Chiral selective optical tweezers to separate enantiomers in different spatial regions. - Abstract: A chiral optical conveyor belt for enantiomeric separation of nanoparticles is numerically demonstrated by using different types of counter propagating elliptical Laguerre Gaussian beams with different beam waist and topological charge. The analysis of chiral resolution has been made for particles immersed in water demonstrating that in the analyzed conditions one type of enantiomer is trapped in a deep potential and the others are transported by the chiral conveyor toward another trap located in a different geometrical region.

Health impact assessment of the Atlanta BeltLine.

Science.gov (United States)

Ross, Catherine L; Leone de Nie, Karen; Dannenberg, Andrew L; Beck, Laurie F; Marcus, Michelle J; Barringer, Jason

2012-03-01

Although a health impact assessment (HIA) is a tool that can provide decision makers with recommendations to promote positive health impacts and mitigate adverse health impacts of proposed projects and policies, it is not routinely conducted on most major projects or policies. To make health a decision criterion for the Atlanta BeltLine, a multibillion-dollar transit, trails, parks, and redevelopment project. An HIA was conducted in 2005-2007 to anticipate and influence the BeltLine's effect on health determinants. Changes in access and equity, environmental quality, safety, social capital, and physical activity were forecast, and steps to maximize health benefits and reduce negative effects were recommended. Key recommendations included giving priority to the construction of trails and greenspace rather than residential and retail construction, making health an explicit goal in project priority setting, adding a public health professional to decision-making boards, increasing the connectivity between the BeltLine and civic spaces, and ensuring that affordable housing is built. BeltLine project decision makers have incorporated most of the HIA recommendations into the planning process. The HIA was cited in the awarding of additional funds of $7,000,000 for brownfield clean-up and greenspace development. The project is expected to promote the health of local residents more than in the absence of the HIA. This report is one of the first HIAs to tie specific assessment findings to specific recommendations and to identifiable impacts from those recommendations. The lessons learned from this project may help others engaged in similar efforts. Copyright © 2012. Published by Elsevier Inc.

Determination of technological parameters in strip mining by time-of-flight and image processing

Science.gov (United States)

Elandaloussi, Frank; Mueller, B.; Osten, Wolfgang

1999-09-01

The conveying and dumping of earth masses lying over the coal seam in lignite surface mining is done usually by overburden conveyor bridges. The overburden, obtained from connected excavators, is transported over the bridge construction using a conveyor belt system and poured into one front dump and three surface dumps. The shaping of the dump growth is of great importance both to guaranty the stability of the masses dumped to earth stocks as well as the whole construction and to prepare the area for re-cultivation. This article describes three measurement systems: one to determine the impact point of the dumped earth masses, one to determine the shape of the entire mining process and the other a sensor for the loading of the conveyor belt. For the first measurement system, a real-time video system has been designed, set-up and installed that is capable to determine the impact point of all three dumps simultaneously. The second measurement system is a connection of 5 special designed laser distance measuring instruments, that are able to measure the shape of the mining process under unfavorable environmental conditions like dust, high temperature changes, heavy shocks etc. The third sensor is designed for monitoring the transportation of the masses via the conveyor belt system.

Testing the application of portable scintillation unit HOU 22 SCS in determining ash content in coal

International Nuclear Information System (INIS)

Simon, L.; Barcalova, L.; Sok, V.; Kacena, V.

1977-01-01

Operating tests were conducted for determining the ash content of coal on the conveyor belt using a portable scintillation radiometric unit of the HOU22 SCS type. The apparatus operated on the principle of scattered gamma radiation from a 75 Se source with an activity of 18 MBq. The detection probe 41 mm in diameter was mounted at the inlet of the coal flow onto the conveyor belt. The accuracy of determination of the ash content of undersize coal used for power production (grain size 0 to 10 mm) was +-4.4%. (B.S.)

An Improved Dispatching Method (a-HPDB for Automated Material Handling System with Active Rolling Belt for 450 mm Wafer Fabrication

Directory of Open Access Journals (Sweden)

Chia-Nan Wang

2017-07-01

Full Text Available The semiconductor industry is facing the transition from 300 mm to 450 mm wafer fabrication. Due to the increased size and weight, 450 mm wafers will pose unprecedented challenges on semiconductor wafer fabrication. To better handle and transport 450 mm wafers, an advanced Automated Material Handling System (AMHS is definitely required. Though conveyor-based AMHS is expected to be suitable for 450 mm wafer fabrication, still it faces two main problems, traffic-jam problem and lot-prioritization. To address the two problems, in this research we have proposed an improved dispatching method, termed Heuristic Preemptive Dispatching Method using Activated Roller Belt (a-HPDB. We have developed some effective rules for the a-HPDB based on Activated Roller Belt (ARB. In addition, we have conducted experiments to investigate its effectiveness. Compared with the HPDB and R-HPD, two dispatching rules proposed in previous studies, our experimental results showed the a-HPDB had a better performance in terms of average lot delivery time (ALDT. For hot lots and normal lots, the a-HPDB had advantages of 4.14% and 8.92% over the HPDB and advantages of 4.89% and 8.52% over R-HPD, respectively.

Breathing of new life.. Rebuild of a CAT 589 pipelayer in the opencast mining Garzweiler; Neues Leben eingehaucht.. Rebuild eines CAT 589 Rohrverlegers im Tagebau Garzweiler

Energy Technology Data Exchange (ETDEWEB)

Plonczynski, Guenter; Sterken, Heinz-Josef [RWE Power Aktiengesellschaft, Grevenbroich (Germany). Tagebau Garzweiler

2011-06-15

Worldwide there are pipelayers at those sites where water pipelines, oil pipelines and gas pipelines are laid. In Germany, pipelayers mainly are used at RWE Power as well as in the opencast mines of the Rhenish mining area. Pipelayers are suitable for moving conveyor systems and for changing of conveyor belts.

Lap belts and three-point belts.

NARCIS (Netherlands)

Kampen, L.T.B. van & Edelman, A.

1975-01-01

Results of the swov-accident investigation prove that if there are any differences in the effectiveness of lap belts and three-point belts, these are so small that they cannot form a basis for giving preference to one type over the other. Furthermore, in spite of the results of this investigation

Simulation of engine auxiliary drive V-belt slip motion. Part 1. Development of belt slip model; Engine hoki V belt slip kyodo no simulation. 1. Belt slip model no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kurisu, T [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

V-belts are widely used for driving auxiliary components of an engine. Inadequet design of such belt system sometimes results in troubles such as belt squeak, side rubber separation and/or bottom rubber crack. However, there has been no design tools which can predict belt slip quantitatively. The author developed a motion simulation program of Auxiliary Drive V-Belt System considering belt slip. The program showed good prediction accuracy for belt slip motion. This paper describes the simulation model. 1 ref., 12 figs.

Seat belt reminders.

NARCIS (Netherlands)

2008-01-01

Seat belts are an effective way of reducing the number or road deaths and severe road injuries in crashes. Seat belt reminders warn car drivers and passengers if the seat belt is not fastened. This can be done by a visual signal or an acoustic signal or by a combination of the two. Seat belt

Apparatus for inspecting the quality of nuclear fuel rod ends

International Nuclear Information System (INIS)

Brashier, R.W.; Pfau, E.D.

1990-01-01

This patent describes an apparatus for inspecting the quality of both ends of nuclear fuel rods. It comprises: a housing including a pair of longitudinally separated slots for receiving X-ray downwardly therethrough from an external source and so as to define first and second longitudinally spaced apart operating positions, means for serially guiding nuclear fuel rods longitudinally through the housing and to a first rod position wherein the forward ends of the rods are aligned below the first operating position and to a second rod position wherein the rear ends of the rods are aligned below the second operating position, belt conveyor assembly means for serially advancing X-ray film cartridges longitudinally through the housing and below the rods, and so that each cartridge may be selectively aligned below the first and second operating positions; and table means supported by the conveyor frame for selectively lifting the film cartridges supported by the belts and so that the conveyor belts may be advanced while the film cartridges are held stationary

CMOS current controlled fully balanced current conveyor

International Nuclear Information System (INIS)

Wang Chunhua; Zhang Qiujing; Liu Haiguang

2009-01-01

This paper presents a current controlled fully balanced second-generation current conveyor circuit (CF-BCCII). The proposed circuit has the traits of fully balanced architecture, and its X-Y terminals are current controllable. Based on the CFBCCII, two biquadratic universal filters are also proposed as its applications. The CFBCCII circuits and the two filters were fabricated with chartered 0.35-μm CMOS technology; with ±1.65 V power supply voltage, the total power consumption of the CFBCCII circuit is 3.6 mW. Comparisons between measured and HSpice simulation results are also given.

On the sensitivity evaluation for on-stream elemental analysis using neutron and photoactivation techniques

International Nuclear Information System (INIS)

Ivanov, I.N.; Zakharov, E.A.; Kasatkin, V.A.; Kartashev, E.R.; Mashinin, V.A.; Feoktistov, Yu.V.; Tchulkin, V.L.

1984-01-01

The paper discusses the data of calculations of neutron and photonactivation effects of moving substances, in particular, bulk materials moving on a conveyor belt and solution streams. The calculated data on minimum detectable concentrations of the various elements are given. The calculation data satisfactorily agree with the experimental data obtained as a result of on-stream neutron activation analysis of solutions containing indium, selenium, aluminium, fluorine and also bulk materials containing aluminium and silicon. The opportunity of applying the bremsstrahlung generated by the electron accelerator for photon activation analysis and sorting gold-bearing ores on the conveyor belt has been analysed

Rare etiological factor of maxillofacial injury: Case series seen and managed in a tertiary referral centre

Directory of Open Access Journals (Sweden)

Ramat Oyebunmi Braimah

2016-01-01

Full Text Available Entanglement injury from local milling/grinding machine with a conveyor belt is a rare etiology of maxillofacial injuries. While there is abundant literature on industrial cause of trauma, entanglement injury as a mechanism has not been reported in the literature. We present two cases of maxillofacial injury secondary to entanglement of the loose apparel into the conveyor belt of the local grinding machine. The community should be aware of this rare cause of trauma, and adequate protection of children using these facilities should be enforced. One of such measure is to provide physical barriers to guard against these machines.

Kinematics and Dynamic Evaluation of the Screw Conveyor of a ...

African Journals Online (AJOL)

An analysis of the vortex motion in a horizontal screw conveyor of a Cassava Centrifuge Dewatering Machine is presented. It is shown that the vortex motion is characterised by the tangential component of the absolute grain velocity being constant with the radial position of a point on the blade. On this basis, an expression ...

Effectiveness of Ford's belt reminder system in increasing seat belt use

OpenAIRE

Williams, A; Wells, J; Farmer, C

2002-01-01

Objectives: The study investigated the effectiveness in increasing seat belt use of Ford's belt reminder system, a supplementary system that provides intermittent flashing lights and chimes for five minutes if drivers are not belted.

Synaptic vesicle distribution by conveyor belt.

Science.gov (United States)

Moughamian, Armen J; Holzbaur, Erika L F

2012-03-02

The equal distribution of synaptic vesicles among synapses along the axon is critical for robust neurotransmission. Wong et al. show that the continuous circulation of synaptic vesicles throughout the axon driven by molecular motors ultimately yields this even distribution. Copyright © 2012 Elsevier Inc. All rights reserved.

chute with the damping plate

Directory of Open Access Journals (Sweden)

V. Molnár

2016-08-01

in detail in three phases of shifting by means of a physical approach with the support of computing methods and simulation experiments with the transfer model. We can state that the direction and orientation of material impact have a direct influence on the conveyor's energy intensity. Thus, the inevitable condition for operation of arbitrary type of belt conveyor is to pay greater attention to the construction of the transfer model, particularly the intensity of the energy of the outgoing conveyor.

Storm-time radiation belt electron dynamics: Repeatability in the outer radiation belt

Science.gov (United States)

Murphy, K. R.; Mann, I. R.; Rae, J.; Watt, C.; Boyd, A. J.; Turner, D. L.; Claudepierre, S. G.; Baker, D. N.; Spence, H. E.; Reeves, G. D.; Blake, J. B.; Fennell, J. F.

2017-12-01

During intervals of enhanced solar wind driving the outer radiation belt becomes extremely dynamic leading to geomagnetic storms. During these storms the flux of energetic electrons can vary by over 4 orders of magnitude. Despite recent advances in understanding the nature of competing storm-time electron loss and acceleration processes the dynamic behavior of the outer radiation belt remains poorly understood; the outer radiation belt can exhibit either no change, an enhancement, or depletion in radiation belt electrons. Using a new analysis of the total radiation belt electron content, calculated from the Van Allen probes phase space density (PSD), we statistically analyze the time-dependent and global response of the outer radiation belt during storms. We demonstrate that by removing adiabatic effects there is a clear and repeatable sequence of events in storm-time radiation belt electron dynamics. Namely, the relativistic (μ=1000 MeV/G) and ultra-relativistic (μ=4000 MeV/G) electron populations can be separated into two phases; an initial phase dominated by loss followed by a second phase dominated by acceleration. At lower energies, the radiation belt seed population of electrons (μ=150 MeV/G) shows no evidence of loss but rather a net enhancement during storms. Further, we investigate the dependence of electron dynamics as a function of the second adiabatic invariant, K. These results demonstrate a global coherency in the dynamics of the source, relativistic and ultra-relativistic electron populations as function of the second adiabatic invariant K. This analysis demonstrates two key aspects of storm-time radiation belt electron dynamics. First, the radiation belt responds repeatably to solar wind driving during geomagnetic storms. Second, the response of the radiation belt is energy dependent, relativistic electrons behaving differently than lower energy seed electrons. These results have important implications in radiation belt research. In particular

Belt attachment and system

Energy Technology Data Exchange (ETDEWEB)

Schneider, Abraham D.; Davidson, Erick M.

2018-03-06

Disclosed herein is a belt assembly including a flexible belt with an improved belt attachment. The belt attachment includes two crossbars spaced along the length of the belt. The crossbars retain bearings that allow predetermined movement in six degrees of freedom. The crossbars are connected by a rigid body that attaches to the bearings. Implements that are attached to the rigid body are simply supported but restrained in pitching rotation.

Identifying the bacterial community on the surface of Intralox belting in a meat boning room by culture-dependent and culture-independent 16S rDNA sequence analysis.

Science.gov (United States)

Brightwell, Gale; Boerema, Jackie; Mills, John; Mowat, Eilidh; Pulford, David

2006-05-25

We examined the bacterial community present on an Intralox conveyor belt system in an operating lamb boning room by sequencing the 16S ribosomal DNA (rDNA) of bacteria extracted in the presence or absence of cultivation. RFLP patterns for 16S rDNA clone library and cultures were generated using HaeIII and MspI restriction endonucleases. 16S rDNA amplicons produced 8 distinct RFLP pattern groups. RFLP groups I-IV were represented in the clone library and RFLP groups I and V-VIII were represented amongst the cultured isolates. Partial DNA sequences from each RFLP group revealed that all group I, II and VIII representatives were Pseudomonas spp., group III were Sphingomonas spp., group IV clones were most similar to an uncultured alpha proteobacterium, group V was similar to a Serratia spp., group VI with an Alcaligenes spp., and group VII with Microbacterium spp. Sphingomonads were numerically dominant in the culture-independent clone library and along with the group IV alpha proteobacterium were not represented amongst the cultured isolates. Serratia, Alcaligenes and Microbacterium spp. were only represented with cultured isolates. Pseudomonads were detected by both culture-dependent (84% of isolates) and culture-independent (12.5% of clones) methods and their presence at high frequency does pose the risk of product spoilage if transferred onto meat stored under aerobic conditions. The detection of sphingomonads in large numbers by the culture-independent method demands further analysis because sphingomonads may represent a new source of meat spoilage that has not been previously recognised in the meat processing environment. The 16S rDNA collections generated by both methods were important at representing the diversity of the bacterial population associated with an Intralox conveyor belt system.

Automation of technological processes at surface mines in the GDR as one of the main directions of increased coal extraction effectiveness by surface mining

Energy Technology Data Exchange (ETDEWEB)

Jona, U.

1987-12-01

In the GDR, about 53% of brown coal is mined with the use of overburden conveyor bridges, 27% with the use of belt conveyors, and 20% with the use of rail transport. Compares efficiency and cost per 1 m/sup 3/ of these transport methods. The overburden conveyor bridges, their specifications and microcomputer control are described. Describes utilization of microcomputer techniques, especially the stereochart system of Carl Zeiss Jena, for automated processing of data on surface mine geometry. Other computer applications are also presented, e.g. for surveying, slope stability calculation, and conveyor bridge control. Maintains that application of the KED/KEM microcomputer system for overburden conveyor bridge control increases its effectiveness by 10%, i.e. by 8 million m/sup 3//a.

Application of logical analysis of data to machinery-related accident prevention based on scarce data

International Nuclear Information System (INIS)

Jocelyn, Sabrina; Chinniah, Yuvin; Ouali, Mohamed-Salah; Yacout, Soumaya

2017-01-01

This paper deals with the application of Logical Analysis of Data (LAD) to machinery-related occupational accidents, using belt-conveyor-related accidents as an example. LAD is a pattern recognition and classification approach. It exploits the advancement in information technology and computational power in order to characterize the phenomenon under study. The application of LAD to machinery-related accident prevention is innovative. Ideally, accidents do not occur regularly, and as a result, companies have little data about them. The first objective of this paper is to demonstrate the feasibility of using LAD as an algorithm to characterize a small sample of machinery-related accidents with an adequate average classification accuracy. The second is to show that LAD can be used for prevention of machinery-related accidents. The results indicate that LAD is able to characterize different types of accidents with an average classification accuracy of 72–74%, which is satisfactory when compared with other studies dealing with large amounts of data where such a level of accuracy is considered adequate. The paper shows that the quantitative information provided by LAD about the patterns generated can be used as a logical way to prioritize risk factors. This prioritization helps safety practitioners make decisions regarding safety measures for machines. - Highlights: • LAD is presented as an innovative approach to prevent machinery-related accidents. • LAD is applied to a very small database of belt-conveyor-related accidents. • Despite scarce data, LAD generates patterns with adequate classification accuracy. • The patterns characterize different types of belt-conveyor-related accidents. • The patterns are useful to belt conveyor risk identification and risk estimation.

Redesign lifts prep output 288%

Energy Technology Data Exchange (ETDEWEB)

Hamric, J

1987-02-01

This paper outlines the application of engineering creativity and how it brought output at an Ohio coal preparation plant up from 12,500 tpd to nearly four times that figure, 48,610 tpd. By streamlining the conveyor systems, removing surplus belt length and repositioning subplants the whole operation was able to run far more efficiently with a greater output. Various other alterations including the raw material supply and management and operating practices were also undertaken to provide a test for the achievements possible with such reorganization. The new developments have been in the following fields: fine coal cleaning, heavy media cyclones, feeders, bins, filter presses, dewatering equipment and settling tanks. Output is now limited only by the reduced demand by the Gavin power station nearby.

Avaliação técnica de um transportador pneumático de grãos por aspiração Technical evaluation of a suction pneumatic grain conveyor

Directory of Open Access Journals (Sweden)

Luís Antônio Bortolaia

2008-04-01

Full Text Available Este trabalho apresenta os resultados da avaliação técnica do protótipo do transportador pneumático de grãos por aspiração ASP 200. O equipamento foi construído para uso em instalações armazenadoras agrícolas, na limpeza de pés de elevadores, moegas e renovação do ar em galerias de silos. Os testes avaliaram características mecânicas do equipamento, descargas de material e ar, perdas de carga, vedação do equipamento, eficiência dos captores e o diâmetro das mangueiras. Os resultados subsidiaram diversas recomendações para melhoria no projeto do equipamento, que aumentarão a sua eficiência operacional. Embora o transporte pneumático seja considerado uma ciência experimental, os autores notaram a falta de procedimentos, parâmetros e orientações para testes e comparações na literatura, que são fundamentais para o desenvolvimento do projeto desses transportadores.This research shows the results that were obtained from technical evaluation of ASP 200 prototype that is a suction pneumatic grain conveyor. This equipment was built to use in agricultural storage facilities to clean bucket elevator feet, loading hoppers and air renovation in silo galleries. The tests have evaluated mechanical characteristics of conveyor, air and material discharges, pressure losses, air infiltration, intake nozzle efficiency and piping diameters. The results have allowed several recommendations to improve equipment design that will increase its operational efficiency. Although pneumatic conveying is considered an experimental science, the authors have perceived the lack of procedures, parameters and orientations to conduct tests and comparisons in literature, that are fundamental to develop a design of this conveyor type.

Economics, organization, and planning in surface mining. Part I. Ekonomika, organizacja, i planowanie w gornictwie odkrywkowym. Czesc I

Energy Technology Data Exchange (ETDEWEB)

Trembecki, A; Uberman, R

1975-01-01

Describes the organization of the Ministry of Mining and Energy of the Polish People's Republic and the Union of the Brown Coal Industry. Principles of organization and management of brown coal mines are also outlined. Analyzed are: management structure of production at brown coal mines, management structure of coal preparation and of brown coal mining planning. Methods of production analysis are also explained including analysis of working time and methods based on photography. Organization of work and management of brown coal surface mines is described: organization of belt conveyor haulage, rail transport, truck transport, organization scheme for relocating belt conveyors and rails in surface mines. (31 refs.) (In Polish)

Three-dimensional data assimilation and reanalysis of radiation belt electrons: Observations of a four-zone structure using five spacecraft and the VERB code

Science.gov (United States)

Kellerman, A. C.; Shprits, Y. Y.; Kondrashov, D.; Subbotin, D.; Makarevich, R. A.; Donovan, E.; Nagai, T.

2014-11-01

Obtaining the global state of radiation belt electrons through reanalysis is an important step toward validating our current understanding of radiation belt dynamics and for identification of new physical processes. In the current study, reanalysis of radiation belt electrons is achieved through data assimilation of five spacecraft with the 3-D Versatile Electron Radiation Belt (VERB) code using a split-operator Kalman filter technique. The spacecraft data are cleaned for noise, saturation effects, and then intercalibrated on an individual energy channel basis, by considering phase space density conjunctions in the T96 field model. Reanalysis during the CRRES era reveals a never-before-reported four-zone structure in the Earth's radiation belts during the 24 March 1991 shock-induced injection superstorm: (1) an inner belt, (2) the high-energy shock-injection belt, (3) a remnant outer radiation belt, and (4) a second outer radiation belt. The third belt formed near the same time as the second belt and was later enhanced across keV to MeV energies by a second particle injection observed by CRRES and the Northern Solar Terrestrial Array riometer network. During the recovery phase of the storm, the fourth belt was created near L*=4RE, lasting for several days. Evidence is provided that the fourth belt was likely created by a dominant local heating process. This study outlines the necessity to consider all diffusive processes acting simultaneously and the advantage of supporting ground-based data in quantifying the observed radiation belt dynamics. It is demonstrated that 3-D data assimilation can resolve various nondiffusive processes and provides a comprehensive picture of the electron radiation belts.

Full-wave current conveyor precision rectifier

Directory of Open Access Journals (Sweden)

Đukić Slobodan R.

2008-01-01

Full Text Available A circuit that provides precision rectification of small signal with low temperature sensitivity for frequencies up to 100 kHz without waveform distortion is presented. It utilizes an improved second type current conveyor based on current-steering output stage and biased silicon diodes. The use of a DC current source to bias the rectifying diodes provides higher temperature stability and lower DC offset level at the output. Proposed design of the precision rectifier ensures good current transfer linearity in the range that satisfy class A of the amplifier and good voltage transfer characteristic for low level signals. Distortion during the zero crossing of the input signal is practically eliminated. Design of the proposed rectifier is realized with standard components.

FLEXOWELL vertical lift systems in underground mining and construction industries

Energy Technology Data Exchange (ETDEWEB)

Paelke, J.W.

1988-06-01

Mining and quarrying companies are seeking improved and more continuous transport methods to reduce their costs. Frequently in the past the use of conveyors has been ruled out in steep mining applications but now the Scholtz FLEXOWELL belting which can be used at angles up to the vertical will enable many mines to consider complete belt conveyor systems for the first time. Applications will include steep conveyors for surface mines and quarries in order to eliminate the need for expensive and noisy fleets of trucks and the associated requirements to maintain haul roads. A further field is in the use of steep or vertical conveyors in underground mines to ensure improved continuity of output in existing shaft systems or reduced development costs in new mines. The Scholtz company, a member of the Nokia Group which had sales of about 3.5 billion U.S. Dollars in 1987, has more than 20 years experience with their FLEXOWELL belts. Over 40,000 units are operating around the world. These are already fully proven for vertical lifts of over 100 m (328ft) and up to 500 m (1,640 ft) is possible. Tonnage ratings of up to 4,000 t/h are achievable. Widespread acceptance of this technology has resulted in unique and major installations over the past few years. This paper reviews various applications - from the viewpoint of successfully proven vertical lift systems as well as the maintenance and downtime aspects. 3 refs., 9 figs.

Earth's radiation belts

International Nuclear Information System (INIS)

Moslehi Fard, M.

1984-01-01

The theory of trapped particles in a magnetic field of approximated dipole is described completely in the first part. Second part contains experimental results. The mechanism of radiation belt source ''albedo neutrons'' and also types of dissipation mechanism about radiation belt is explained. The trapped protons and electrons by radiation belt is discussed and the life-time of trapped particles are presented. Finally the magnetic fields of Moon, Venus, Mars, and Saturn, measured by passengers Mariner 4,10 and pioneer 10,11 are indicated. The experimental and theoretical results for the explanation of trapped plasma around the earth which is looked like two internal and external belt have almost good correspondence

Global ocean conveyor lowers extinction risk in the deep sea

Science.gov (United States)

Henry, Lea-Anne; Frank, Norbert; Hebbeln, Dierk; Wienberg, Claudia; Robinson, Laura; van de Flierdt, Tina; Dahl, Mikael; Douarin, Mélanie; Morrison, Cheryl L.; López Correa, Matthias; Rogers, Alex D.; Ruckelshausen, Mario; Roberts, J. Murray

2014-06-01

General paradigms of species extinction risk are urgently needed as global habitat loss and rapid climate change threaten Earth with what could be its sixth mass extinction. Using the stony coral Lophelia pertusa as a model organism with the potential for wide larval dispersal, we investigated how the global ocean conveyor drove an unprecedented post-glacial range expansion in Earth's largest biome, the deep sea. We compiled a unique ocean-scale dataset of published radiocarbon and uranium-series dates of fossil corals, the sedimentary protactinium-thorium record of Atlantic meridional overturning circulation (AMOC) strength, authigenic neodymium and lead isotopic ratios of circulation pathways, and coral biogeography, and integrated new Bayesian estimates of historic gene flow. Our compilation shows how the export of Southern Ocean and Mediterranean waters after the Younger Dryas 11.6 kyr ago simultaneously triggered two dispersal events in the western and eastern Atlantic respectively. Each pathway injected larvae from refugia into ocean currents powered by a re-invigorated AMOC that led to the fastest postglacial range expansion ever recorded, covering 7500 km in under 400 years. In addition to its role in modulating global climate, our study illuminates how the ocean conveyor creates broad geographic ranges that lower extinction risk in the deep sea.

Underground fires in oil shale mines: special traits of their spreading, extinguishing and liquidating of consequences

International Nuclear Information System (INIS)

Parakhonsky, E.

1995-01-01

Danger of catching fire in oil shale underground mines has considerably increased lately because of essential increase in mechanization level and frequent violation of fire-safety regulations. The largest underground fire in Estonia took place in the most mechanized mine 'Estonia' in the end of 1988 and lasted 81 days. The fire started in one of the conveyor drifts where two belt-conveyors with rubber-rope belts and a fire pipeline were installed. At the start of the fire and beginning of extinguishing work this pipeline contained no water. Driving heads of these conveyors were installed with automatic extinguishing equipment and with different primary means against fire. When the first group of the Johvi military mine-rescue squad reached the mine they established that the conveyor drift, pillars and a part of rail drift between them were caught by fire. The conveyor belt, oil shale and feeds of conveyor drives were burning. The flame had propagated about 350 metres along the rail and conveyor drifts but the smoke had spread 4 kilometres already. Air temperature near the burning area was about 40-60 deg C, rocks from the roof supported by pillars had crashed down. The mine air was polluted by combustion products. The fire caused a noticeable pollution of mine and surface waters with phenols formed at oil shale combustion. Their limit concentration was exceeded for more than 400 times. To decrease this number, an intensive saturation of waters with atmosphere air was started. For this purpose special dams were constructed on water-diversion ditches ensuring a 0.5-0.7 m difference in water levels. Nevertheless, the phenol concentration in Rannapungerya River and Lake Peipsi still exceeded the normal level 5-6 times. However, the actual maximum concentration of phenols was considerably lower than the lethal doses for fish and other water organisms. Their mass extinction in the river or in the lake was observed neither during nor after the fire. One may conclude the

Analysis of stress distribution of timing belts by FEM; Yugen yosoho ni yoru timing belt oryoku kaiseki (belt code oryoku bunpu kaiseki hokoku)

Energy Technology Data Exchange (ETDEWEB)

Furukawa, Y; Tomono, K; Takahashi, H; Uchida, T [Honda R and D Co. Ltd., Tokyo (Japan)

1997-10-01

A model of the belt analyzed by-ABAQUS (: a general nonlinear finite element program) successfully confirmed the mechanism that generates the belt cord stress. A quite good agreement between experimental and computed results for the stress distribution of the belt cord. It is found that maximum stress of the cords occurs near the root of the tooth by calculation, where the belt cords break off. 3 refs., 9 figs.

Case study: highly loaded MSE bridge supporting structure, Syncrude NMAPS conveyor overpasses

Energy Technology Data Exchange (ETDEWEB)

Scherger, B.; Brockbank, B. [Reinforced Earth Company Ltd., Edmonton, AB (Canada); Mimura, W. [Syncrude Canada Ltd., Edmonton, AB (Canada)

2005-07-01

A crusher and conveyor system was constructed at the Mildred Lake Oil Sands Mine near Fort McMurray, Alberta in order to facilitate ore delivery from Syncrude's North Mine. As part of this North Mine Auxiliary Production System (NMAPS), Syncrude Canada and their consultant Cosyn Technology identified the need for 3 overpasses over conveyors in the North Mine in order to provide unrestricted crossing over the operating conveyor system for the heavy hauler trucks and light vehicle mine traffic. The overpasses were designed to support the dead load of the granular fill and the live load of two loaded heavy hauler trucks, with a design load for each loaded hauler of 670 900 kg. This paper reviewed various aspects of the design from planning, structure selection, and overall stability and bearing capacity considerations. The different designs in the 3 new overpasses accommodated foundation and loading requirements. The designs ranged from the use of precast one-piece reinforced concrete arches, Mechanically Stabilized Earth (MSE) bridge abutment technology, and a combination of the two. The MSE retaining walls directly supported the bridge superstructure without the use of piles or other deep structural foundations. The design was challenging because of the significant vertical stresses transferred onto the wall. All 3 overpasses also used MSE walls for the supporting end wing walls. The main focus of this paper was on the heavily loaded MSE walls supporting the bridge abutment style overpasses. This structure has illustrated the capability of properly designed MSE wall structures with steel soil reinforcement and reinforced precast concrete face panels to successfully carry bridge footing pressure loadings up to 545 kPa. It was concluded that this case has good potential for use in future bridge projects in both the industrial and highway sectors. 2 refs., 7 figs.

Physical and mechanical properties of spinach for whole-surface online imaging inspection

Science.gov (United States)

Tang, Xiuying; Mo, Chang Y.; Chan, Diane E.; Peng, Yankun; Qin, Jianwei; Yang, Chun-Chieh; Kim, Moon S.; Chao, Kuanglin

2011-06-01

The physical and mechanical properties of baby spinach were investigated, including density, Young's modulus, fracture strength, and friction coefficient. The average apparent density of baby spinach leaves was 0.5666 g/mm3. The tensile tests were performed using parallel, perpendicular, and diagonal directions with respect to the midrib of each leaf. The test results showed that the mechanical properties of spinach are anisotropic. For the parallel, diagonal, and perpendicular test directions, the average values for the Young's modulus values were found to be 2.137MPa, 1.0841 MPa, and 0.3914 MPa, respectively, and the average fracture strength values were 0.2429 MPa, 0.1396 MPa, and 0.1113 MPa, respectively. The static and kinetic friction coefficient between the baby spinach and conveyor belt were researched, whose test results showed that the average coefficients of kinetic and maximum static friction between the adaxial (front side) spinach leaf surface and conveyor belt were 1.2737 and 1.3635, respectively, and between the abaxial (back side) spinach leaf surface and conveyor belt were 1.1780 and 1.2451 respectively. These works provide the basis for future development of a whole-surface online imaging inspection system that can be used by the commercial vegetable processing industry to reduce food safety risks.

Dynamic trial of an on-stream analyser for iron ore fines

International Nuclear Information System (INIS)

Holmes, R.J.; Miles, J.G.

1980-01-01

A thermal neutron irradiation technique using a 252 Cf neutron source has been developed and applied to the simultaneous determination of iron and aluminium (expressed as Al 2 O 3 ) in iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. While the determination of iron with this technique is based on the use of a NaI(Tl) detector to monitor the characeristic prompt gamma rays (7.64 MeV) emitted by thermal neutron capture reactions in the iron, the determination of Al 2 O 3 is based on the use of a second NaI(Tl) detector to monitor the characteristic gamma rays (1.78 MeV) emitted after thermal neutron activation of the aluminium. The second detector is located downstream from the first. Although the speed of the conveyor belt has no direct effect on the iron measurements, it must not exceed about 3 m/min if good accuracy is required for the Al 2 O 3 measurements. Consequently an auxiliary conveyor belt is required in order to avoid interference with normal ore processing. Dynamic trials of the technique have demonstrated that the method can achieve accuracies of 0.7% Fe and 0.1% Al 2 O 3

Neutron activation as an online procedure in cement plants; Neutronenaktivierung als Online-Verfahren in Zementwerken

Energy Technology Data Exchange (ETDEWEB)

Anon.

2012-07-01

The use of PGNAA (Prompt Gamma Neutron Activation Analysis) makes it possible to determine the content of the components in bulk flows in cement plants directly online on the conveyor belt. The nature of the excitation and radiation means that the material can be penetrated even with large layer thicknesses on the belt. (orig.)

Study on mechanics of driving drum with superelastic convexity surface covering-layer structure

Energy Technology Data Exchange (ETDEWEB)

Xiao, L.J.; Sui, X.H.; Miao, D.J. [Shandong University of Science & Technology, Qingdao (China)

2008-09-15

Belt conveyor is one of the main transport equipment in coal mine and the driving drum is its key part. With the method of bionic design, the mushroom morphological structure is applied to the design of covering-layer structure of driving drum surface of belt conveyor. Superelastic rubber with large deformation is adopted as the covering-layer material. Nonlinear constitutive model of rubber, which is of superelasticity and large deformation, is established. The stress states and deformation principles of driving drums including both bionic covering-layer and common covering-layer are obtained by static intensity analysis with Finite Element Analysis (FEA) software ANSYS. The values of the stress and strain on the driving drum surface are gotten and the dangerous area is determined. FEA results show that the superelastic convexity surface structure can enlarge the contact area between the driving drum and viscoelastic belt. The results also show that in comparison with common driving drum, the bionic surface driving drum can not only increase the friction coefficient between drum and belt but also prolong its service life.

Realization of Nth-Order Voltage Transfer Function using Current Conveyors CCII

Directory of Open Access Journals (Sweden)

K. Vrba

1997-06-01

Full Text Available A universal method for the realization of arbitrary voltage transfer function in canonic form is presented. A voltage-controlled current-source using a plus-type second-generation current conveyor is here applied as the basic building element. Filters designed according to this method have a high input impedance and low sensitivity to variations of circuit parameters. All passive elements are grounded.

Irradiation process validation in the new conveyor system installed at PISI: special dosimetry

International Nuclear Information System (INIS)

Pantano, Barbara P.; Docters, Andrea S.

2009-01-01

Semi Industrial Irradiation Plant (PISI) is a multipurpose facility which uses 60 Co sources to treat different products with numerous purposes, such as sterilization of medical devices, pharmaceutical and veterinarian products; control of pathogenic microorganisms, shelf-life extension and insect disinfestation of food, among others. In order to achieve the desired effect, the product is carried inside the irradiation chamber by means of a conveyor system, and it is exposed to radiation following a pre-established path. The recent installation of a new conveyor system at PISI demands the execution of a thorough validation programme. The scope of this presentation is to describe the dose mapping tasks that will be performed in order to characterize the irradiator and its new conveyor system with respect to distribution and variability of dose, complying with international standards on good irradiation practices. Information about the distribution and variability of dose in a product irradiated under defined conditions will allow the obtaining of process parameters which will conform the process specifications in future routine irradiations. The initial stages of the Validation Programme are the Installation Qualification, the Operational Qualification (OQ) and the Performance Qualification (PQ). To accomplish the IQ diverse tests are being carried out at PISI in order to verify that the system has been installed and is operating according to its technical specifications. Both OQ and PQ require dose mapping on simulated and real product, respectively. Dose mapping consists on placing dosimeters on a process load of homogeneous material -under certain irradiator and process parameters- according to a three-dimensional pre-established placement pattern. Since the replacement of the conveyor system introduces a significant modification in the source-to-product geometry, therefore in dose distribution, there is no reference dosimetry data available, so a more exhaustive

City transport of the future - the high speed pedestrian conveyor. Part 1: ergonomic considerations of accelerators, decelerators and transfer sections.

Science.gov (United States)

Browning, A C

1974-12-01

In this article, an uncommon form of passenger transport is considered, the moving pavement or pedestrian conveyor running at speeds of up to 16 km/h. There are very little relevant ergonomic data for such devices and some specific laboratory experiments have been carried out using 1000 subjects to represent the general public. It is concluded that whilst high speed pedestrian conveyors are quite feasible, stations along them are likely to be large. The most attractive type is a set of parallel surfaces moving at different speeds and with handholds provided in the form of poles. This type could be extremely convenient for certain locations but will probably have to be restricted in its use to fairly fit adults carrying little luggage, and would find applications in situations where a large number of people need to travel in the same direction. Part 2, Ergonomic considerations of complete conveyor systems, will follow.

Sandvik sharpens in-pit crushing focus

Energy Technology Data Exchange (ETDEWEB)

Casteel, K.

2009-04-15

Major mining equipment supplier Sandvik Mining and Construction has announced a full-fledged fully mobile crushing plant, the PF300. This is shaping up to be the decade's major addition to the large scale open-cut mining toolkit. The PF300 can be connected to a face conveyor by a loading bridge as well as by belt wagon or transfer conveyor. The article describes design features. 2 figs.

A MACHINE FOR PULVERIZING AND SIFTING GARI MASH

African Journals Online (AJOL)

Dr Obe

O.75kw electric motor. Fig. 2.Photograph of prototype gari pulverizing/sifting machine. A Side view of the Prototype Gari mash Pulverize/sifting machine. 1. Vee-belt drives; 2. Head pulley; 3 belt conveyor; 4, cake breaker, 5. tail pulley; 6. lump or cake of' gari mash;7hopper; 8pulverizing roller; 9. Side gaurds; 10.brush 11.

A conveyor system for feeding work stations

International Nuclear Information System (INIS)

Sheader, J.; Davies, K.J.

1986-01-01

A conveyor system comprises carriages drive, e.g. by a linear motor, a pre-arranged sequence of steps to move workpieces in forward and reverse directions between work stations. Each work station has a part position and a work position and each carriage has a number of compartments for workpieces spaced apart at a pitch equal to the spacing between the part and work positions at each station. Transfer means at the work stations move workpieces between the carriage compartments and the part and work positions. The workpieces can be nuclear fuel pins mounted in carriers and the carriages shuttle to and fro between adjacent stations to move fuel pins and carriers in a forward direction and the return empty carriers in a reverse direction. (author)

Smart Idlers : RFID in conveyor belt monitoring

NARCIS (Netherlands)

Pang, Y.

2012-01-01

Radio Frequency Identifi cation (RFID) is a technology that offers unique identifi cation of objects and processes. It can actively or passively communicate and, in combination with sensors, it can capture more detailed physical information. RFID technology has been integrated into our daily life.

Durability Testing of Idlers for Belt Conveyors

Directory of Open Access Journals (Sweden)

Andrzej Pytlik

2013-01-01

On the basis of the durability tests carried out on both of these idlers it can be concluded that the applied research methodology describes the test conditions of idlers, in a manner as close as possible to their actual operational conditions, which were subject to a variety of factors for a total time of 116 hours, they included: dust, water, loads and variable rotational speed. This methodology allowed us to determine, even at the stage of laboratory tests, the suitability of a particular idler to certain operational conditions.

Belt drive construction improvement

Directory of Open Access Journals (Sweden)

I.Yu. Khomenko

2012-08-01

Full Text Available The possibility of the traction capacity increase of the belt drive TRK is examined. This was done for the purpose of air conditioning system of passenger car with double-generator system energy supplying. Belts XPC (made by the German firm «Continental ContiTech» testing were conducted. The results confirmed the possibility of their usage in order to improve belt drive TRK characteristics.

Application of the simulation of a tank capacity proposal for loading and unloading process of bulk material

Directory of Open Access Journals (Sweden)

Janka Šaderová

2012-12-01

Full Text Available n this paper, the algorithm is given - how to design a tankfor bulk materials. An important part of the proposal is to setthe loading and unloading of a tank, which is also closely related to the proposal of its capacity and volume. Loading and unloadingprocess is dependent on several factors but the main are: method and speed of loading which represents the parameter - hour powerof loading device (e.g. continuous by a conveyor belt, method andspeed of unloading (continuousor at intervals and a typeand capacity of means of transport, in which the material loading (truck, rail car, conveyor belt system. The paper presents twomethods for determination of the loadingand unloading process - the graphic method and determination during the simulation -creating a simulation model.

Continuous process electrorefiner

Science.gov (United States)

Herceg, Joseph E [Naperville, IL; Saiveau, James G [Hickory Hills, IL; Krajtl, Lubomir [Woodridge, IL

2006-08-29

A new device is provided for the electrorefining of uranium in spent metallic nuclear fuels by the separation of unreacted zirconium, noble metal fission products, transuranic elements, and uranium from spent fuel rods. The process comprises an electrorefiner cell. The cell includes a drum-shaped cathode horizontally immersed about half-way into an electrolyte salt bath. A conveyor belt comprising segmented perforated metal plates transports spent fuel into the salt bath. The anode comprises the conveyor belt, the containment vessel, and the spent fuel. Uranium and transuranic elements such as plutonium (Pu) are oxidized at the anode, and, subsequently, the uranium is reduced to uranium metal at the cathode. A mechanical cutter above the surface of the salt bath removes the deposited uranium metal from the cathode.

Design and manufacture NCS instruments for cement factories

International Nuclear Information System (INIS)

Nguyen Thanh Tuy; Nguyen Tien Dung; Dang Nguyet Anh; Nguyen Phuc; Khuong Thanh Tuan; Luong Duc Long; Pham Trong Quyen

2003-01-01

The ministry project 'Design and manufacture some of NCS instruments for cement factories' is a part of instrumentation for cement production in Vietnam. The objectives of the project include: 1/Design and manufacture the automatic control system for cement raw material mixing, connected to components X-ray analyzer through serial port of PC; 2/Design and manufacture the automatic discharge control system using gamma rays. The instruments, made by the project , for controlling the conveyor belt weighing machine can be easily improved for various types of conveyor belt weighing machines. Their mobility and software equipped can be adapted for requirement of modern cement production technology. The instruments are operating well in some cement factories and they are helping in quality control. (NHA)

Bulk analysis using nuclear techniques

International Nuclear Information System (INIS)

Borsaru, M.; Holmes, R.J.; Mathew, P.J.

1983-01-01

Bulk analysis techniques developed for the mining industry are reviewed. Using penetrating neutron and #betta#-radiations, measurements are obtained directly from a large volume of sample (3-30 kg) #betta#-techniques were used to determine the grade of iron ore and to detect shale on conveyor belts. Thermal neutron irradiation was developed for the simultaneous determination of iron and aluminium in iron ore on a conveyor belt. Thermal-neutron activation analysis includes the determination of alumina in bauxite, and manganese and alumina in manganese ore. Fast neutron activation analysis is used to determine silicon in iron ores, and alumina and silica in bauxite. Fast and thermal neutron activation has been used to determine the soil in shredded sugar cane. (U.K.)

Equilibria and Free Vibration of a Two-Pulley Belt-Driven System with Belt Bending Stiffness

Directory of Open Access Journals (Sweden)

Jieyu Ding

2014-01-01

Full Text Available Nonlinear equilibrium curvatures and free vibration characteristics of a two-pulley belt-driven system with belt bending stiffness and a one-way clutch are investigated. With nonlinear dynamical tension, the transverse vibrations of the translating belt spans and the rotation motions of the pulleys and the accessory shaft are coupled. Therefore, nonlinear piecewise discrete-continuous governing equations are established. Considering the bending stiffness of the translating belt spans, the belt spans are modeled as axially moving beams. The pattern of equilibria is a nontrivial solution. Furthermore, the nontrivial equilibriums of the dynamical system are numerically determined by using two different approaches. The governing equations of the vibration near the equilibrium solutions are derived by introducing a coordinate transform. The natural frequencies of the dynamical systems are studied by using the Galerkin method with various truncations and the differential and integral quadrature methods. Moreover, the convergence of the Galerkin truncation is investigated. Numerical results reveal that the study needs 16 terms after truncation in order to determine the free vibration characteristics of the pulley-belt system with the belt bending stiffness. Furthermore, the first five natural frequencies are very sensitive to the bending stiffness of the translating belt.

Lap belt injuries in children.

LENUS (Irish Health Repository)

McGrath, N

2010-07-01

The use of adult seat belts without booster seats in young children may lead to severe abdominal, lumbar or cervical spine and head and neck injuries. We describe four characteristic cases of lap belt injuries presenting to a tertiary children\\'s hospital over the past year in addition to a review of the current literature. These four cases of spinal cord injury, resulting in significant long-term morbidity in the two survivors and death in one child, arose as a result of lap belt injury. These complex injuries are caused by rapid deceleration characteristic of high impact crashes, resulting in sudden flexion of the upper body around the fixed lap belt, and consequent compression of the abdominal viscera between the lap belt and spine. This report highlights the dangers of using lap belts only without shoulder straps. Age-appropriate child restraint in cars will prevent these injuries.

20 CFR 655.502 - Definitions.

Science.gov (United States)

2010-04-01

... equipped with an automated self-unloading conveyor belt or vacuum-actuated system which is utilized for... alien crewmembers is not intended or designed to influence an election of a bargaining representative...

A computer program (FUGI) for design and operation of a conveyor type irradiator with multi-tier and multi-layer

International Nuclear Information System (INIS)

Hoshi, Tatsuo; Aggarwal, K.S.

1976-10-01

A computer program (FUGI) was established to facilitate the determination of factors related to design and operation of a conveyor type irradiator with multi-tier and multi-layer. The factors determined by this program are as follows: (1) maximum dose, minimum dose and dose uniformity in irradiated material; (2) dose rate distribution on the path of irradiated material; (3) mass flow rate of irradiated material; (4) requisite activity of source; (5) requisite speed of conveyor; (6) utilization efficiency. This program partly uses the program FUDGE 4A for determination of dose rate in irradiated material in static state by Galanter and Krishnamurthy. (auth.)

40 CFR 63.1445 - What work practice standards must I meet for my fugitive dust sources?

Science.gov (United States)

2010-07-01

...) Each transfer point in conveying systems used to transport fugitive dust materials. These points include, but are not limited to, transfer of material from one conveyor belt to another and transfer of...

Engineering study on conveyor system for HC-21C project

International Nuclear Information System (INIS)

De Vries, M.L.

1995-01-01

The sludge stabilization process thermally stabilizes reactive plutonium bearing materials in a muffle furnace. This process is used to prepare the material for long term storage in the vaults. The process is conducted in Room 230A and 230B. The furnaces are located in glovebox HC-21C. Glovebox HC-21A is used for preparation of the charge and packaging of the high fired oxide. The feed for the process is located throughout the PRF and RMC-line gloveboxes, with over half of the feedstock currently being located in HA-23S. For readiness assessment, the sludge stabilization process at PFP was reviewed by the ALARA team to see how the process could be improved. One suggestion was made that the conveyor system be used to transfer items from HA-23S to the process glovebox (HA-21A) instead of sealing items in and out of the gloveboxes. The following discussion describes and compares past and current methods. In addition, actions are addressed that would need to be completed before the conveyor method could be used. The transportation of the feedstock to the process and all the different influencing factors will be examined to determine the best method. This assessment is being performed considering only the current campaign for HC-21C. However, there is a possibility that in the future, additional furnaces will be installed and further campaigns done

Drivers' attitudes toward front or rear child passenger belt use and seat belt reminders at these seating positions.

Science.gov (United States)

Kidd, David G; McCartt, Anne T

2014-01-01

Passengers, especially those in rear seating positions, use seat belts less frequently than drivers. In-vehicle technology can inform drivers when their passengers are unbuckled and encourage passengers to use belts. The current study collected information about drivers' attitudes toward passenger belt use and belt reminders for front passengers and children in back seats. A national telephone survey of 1218 people 18 and older was conducted, of which 477 respondents were drivers who transport a front seat passenger at least once a week and 254 were drivers who transport an 8- to 15-year-old child in the back seat. Respondents were asked about their attitudes toward belt use by their front passengers or rear child passengers and preferences for different passenger belt reminder features. Ninety percent of drivers who regularly transport front seat passengers said that the passengers always use seat belts. Reported belt use was even higher among 8- to 15-year-old children in the back seat (97%). Among the drivers whose children do not always buckle up, about half said their child unbuckled the belt during the trip. Almost every full-time belt use driver (96%) would encourage front passengers to buckle up if not belted, compared to 57 percent of part-time belt users and nonusers. In contrast, nearly every driver who transports children in the back seat would encourage their belt use, regardless of the driver's belt use habits. Most drivers who transport front passengers wanted passenger belt reminders to encourage passengers to buckle up. Most of these drivers wanted a chime/buzzer or warning light or text display and wanted the reminder to last indefinitely. Most drivers who transport child passengers in the rear seat wanted the vehicle to indicate whether child passengers are unbuckled. A large majority of these drivers wanted notifications via a visual diagram of seating positions and belt use, a chime/buzzer, and a warning light or text display. These drivers

Occurrence and Species Distribution of Strictly Anaerobic Bacterium Pectinatus in Brewery Bottling Halls

Czech Academy of Sciences Publication Activity Database

Matoulková, D.; Kosař, K.; Slabý, M.; Sigler, Karel

2012-01-01

Roč. 70, č. 4 (2012), s. 262-267 ISSN 0361-0470 Institutional support: RVO:61388971 Keywords : Beer spoilage * Biofilm * Conveyor belt Subject RIV: EE - Microbiology, Virology Impact factor: 1.000, year: 2012

20 CFR 655.610 - Automated vessel exception to prohibition on utilization of alien crewmember(s) to perform...

Science.gov (United States)

2010-04-01

...., vessels equipped with automated self- unloading conveyor belts or vacuum-actuated systems) to use alien...) With intent or design to influence an election of a bargaining representative for workers at the U.S...

Clock synchronization and dispersion

International Nuclear Information System (INIS)

Giovannetti, Vittorio; Lloyd, Seth; Maccone, Lorenzo; Wong, Franco N C

2002-01-01

We present a method to defeat effects of dispersion of timing signals when synchronizing clocks. It is based on the recently proposed 'conveyor belt synchronization' scheme and on the quantum dispersion cancellation effect

Microbiological survey of a South African poultry processing plant.

Science.gov (United States)

Geornaras, I; de Jesus, A; van Zyl, E; von Holy, A

1995-01-01

Bacterial populations associated with poultry processing were determined on neck skin samples, equipment surfaces and environmental samples by replicate surveys. Aerobic plate counts, Enterobacteriaceae counts, Enterobacteriaceae counts and Pseudomonas counts were performed by standard procedures and the prevalence of Listeria, presumptive Salmonella and Staphylococcus aureus determined. Statistically significant (P defeathering curtains, shackles and conveyor belts repeatedly showed aerobic plate counts in excess of 5.0 log CFU 25 cm-2. Aerobic plate counts of scald tank and spinchiller water were 2 log CFU ml-1 higher than those of potable water samples. Bacterial numbers of the air in the "dirty" area were higher than those of the "clean" area. Listeria, presumptive Salmonella and Staphylococcus aureus were isolated from 27.6, 51.7 and 24.1% of all product samples, respectively, and Listeria and Staphylococcus aureus were also isolated from selected equipment surfaces.

46 CFR 172.245 - Survival conditions.

Science.gov (United States)

2010-10-01

... seals to cargo hopper gates; or (ii) Guillotine doors in bulkheads in way of the conveyor belt. ... inches (50 mm) when the vessel is in the equilibrium position. (e) Progressive flooding. In the design...

Study on the share of energy consumption by components of the technological process with aim of reducing total energy consumption. Principijelno razmatranje energetskog ucesca pojedinih komponenti tehnoloskog procesa u smislu iznalazenja rjesenja sa najmanjim energetskim ucescem

Energy Technology Data Exchange (ETDEWEB)

Kljucanin, T. (Institut za Rudarska Istrazivanja, Tuzla (Yugoslavia))

1989-01-01

Analyzes individual phases of coal excavation in surface mines from the viewpoint of energy consumption. Equipment operation with unnecessary lifting of loosened overburden or coal on mine benches during bulk loading into dump trucks, onto belt conveyors or during transportation is pointed out. Energy consumption calculations showed that unnecessary bulk lifting by equipment configurations results in annual energy losses, both fuel or electricity. A mathematical formula for calculating energy losses is provided. A calculation example with surface mining operations is given, demonstrating that 55 MWh per excavator may be saved over a 25 year period if lifting height of overburden were reduced by 22 m. Overburden removal equipment employed consists of the PH-1900 shovel excavator, 60 to 155 t capacity dump trucks and inclined belt conveyor system. 1 ref.

Creation of the Project of a Logistic System for Transportation of Minerals - Case Study

Directory of Open Access Journals (Sweden)

Daniela Marasova

2017-05-01

Full Text Available One of the possibilities how to maintain the competitiveness of mining and processing undertakings on the minerals market is to increase the efficiency of the minerals recovery and processing process with the focus on the operating costs reduction. Intra-plant transportation plays an important role in this process. Optimization of minerals transportation and implementation of the logistic approach can result in significant saving of operating costs pertaining to the recovered number of valuable mineral. The article presents a logistic approach to the belt conveyor system designing, proposes possible modifications of selected parameters of belt conveyors in a particular processing plant, and monitors their impact on the improvement of operating, but mainly economic parameters of transportation of clay and limestone, while maintaining the required transportation capacity.

Design and testing of small scale fish meat bone separator useful for fish processing.

Science.gov (United States)

Ali Muhammed, M; Manjunatha, N; Murthy, K Venkatesh; Bhaskar, N

2015-06-01

The present study relates to the food processing machinery and, more specifically machine for producing boneless comminuted meat from raw fish fillet. This machine is of belt and drum type meat bone separator designed for small scale fish processing in a continuous mode. The basic principal involved in this machine is compression force. The electric geared motor consists of 1HP and the conveyor belt has a linear velocity of 19 to 22 m min(-1), which was sufficient to debone the fish effectively. During the meat bone separation trials an efficiency up to 75 % on dressed fish weight basis was observed and with a capacity to separate 70 kg h(-1) of meat from fish at the machine speed of 25 rpm. During the trials, it was demonstrated that there was no significant change in the proximate composition of comminuted fish meat when compared to unprocessed fish meat. This design has a greater emphasis on hygiene, provision for cleaning-in-place (CIP) and gives cost effective need and reliability for small scale industries to produce fish meat in turn used for their value added products.

Description of pelletizing facility

Energy Technology Data Exchange (ETDEWEB)

Vojin Cokorilo; Dinko Knezevic; Vladimir Milisavljevic [University of Belgrade, Belgrade (Serbia). Faculty of Mining and Geology

2006-07-01

A lot of electrical energy in Serbia was used for heating, mainly for domestics. As it is the most expensive source for heating the government announced a National Program of Energy Efficiency with only one aim, to reduce the consumption of electric energy for the heating. One of the contributions to mentioned reduction is production of coal pellets from the fine coal and its use for domestic heating but also for heating of schools, hospitals, military barracks etc. Annual production of fine coal in Serbia is 300,000 tons. The stacks of fine coal present difficulties at each deep mine because of environmental pollution, spontaneous combustion, low price, smaller market etc. To overcome the difficulties and to give the contribution to National Program of Energy Efficiency researchers from the Department of Mining Engineering, the University of Belgrade designed and realized the project of fine coal pelletizing. This paper describes technical aspect of this project. Using a CPM machine Model 7900, a laboratory facility, then a semi-industrial pelletizing facility followed by an industrial facility was set up and produced good quality pellets. The plant comprised a coal fines hopper, conveyor belt, hopper for screw conveyor, screw conveyor, continuous mixer conditioner, binder reservoir, pump and pipelines, pellet mill, product conveyor belt and product hopper. 4 refs., 3 figs., 1 tab.

VERO cells harbor a poly-ADP-ribose belt partnering their epithelial adhesion belt

Directory of Open Access Journals (Sweden)

Laura Lafon-Hughes

2014-10-01

Full Text Available Poly-ADP-ribose (PAR is a polymer of up to 400 ADP-ribose units synthesized by poly-ADP-ribose-polymerases (PARPs and degraded by poly-ADP-ribose-glycohydrolase (PARG. Nuclear PAR modulates chromatin compaction, affecting nuclear functions (gene expression, DNA repair. Diverse defined PARP cytoplasmic allocation patterns contrast with the yet still imprecise PAR distribution and still unclear functions. Based on previous evidence from other models, we hypothesized that PAR could be present in epithelial cells where cadherin-based adherens junctions are linked with the actin cytoskeleton (constituting the adhesion belt. In the present work, we have examined through immunofluorescence and confocal microscopy, the subcellular localization of PAR in an epithelial monkey kidney cell line (VERO. PAR was distinguished colocalizing with actin and vinculin in the epithelial belt, a location that has not been previously reported. Actin filaments disruption with cytochalasin D was paralleled by PAR belt disruption. Conversely, PARP inhibitors 3-aminobenzamide, PJ34 or XAV 939, affected PAR belt synthesis, actin distribution, cell shape and adhesion. Extracellular calcium chelation displayed similar effects. Our results demonstrate the existence of PAR in a novel subcellular localization. An initial interpretation of all the available evidence points towards TNKS-1 as the most probable PAR belt architect, although TNKS-2 involvement cannot be discarded. Forthcoming research will test this hypothesis as well as explore the existence of the PAR belt in other epithelial cells and deepen into its functional implications.

Comparison of sliding friction and wear behaviour of overhead conveyor steels tested under dry and lubrication conditions

International Nuclear Information System (INIS)

Castro-Regal, G.; Fernandez-Vicente, A.; Martinez, M. A.

2005-01-01

The sliding friction and wear behaviour of different steel qualities were investigated with and without lubrication conditions. Steel qualities tested are normally used in the overhead conveyor system of many industrial fields, like the automotive sector. Sliding wear tests have been conducted by means of a pin-on-disk machine. A 100Cr6 steel similar to that used within the overhead conveyor trolleys has been employed as a pin. Friction coefficient values obtained under lubrication conditions were three times smaller than those obtained without lubrication. The mechanism that controls wear behaviour under lubrication conditions is an abrasive one and the wear values obtained are almost worthless. On the other hand, mechanism controlling wear during non lubrication tests, was a combination of abrasion and adhesion. (Author) 20 refs

Pelvic belt effects on sacroiliac joint ligaments: a computational approach to understand therapeutic effects of pelvic belts.

Science.gov (United States)

Sichting, Freddy; Rossol, Jerome; Soisson, Odette; Klima, Stefan; Milani, Thomas; Hammer, Niels

2014-01-01

The sacroiliac joint is a widely described source of low back pain. Therapeutic approaches to relieve pain include the application of pelvic belts. However, the effects of pelvic belts on sacroiliac joint ligaments as potential pain generators are mostly unknown. The aim of our study was to analyze the influence of pelvic belts on ligament load by means of a computer model. Experimental computer study using a finite element method. A computer model of the human pelvis was created, comprising bones, ligaments, and cartilage. Detailed geometries, material properties of ligaments, and in-vivo pressure distribution patterns of a pelvic belt were implemented. The effects of pelvic belts on ligament strain were computed in the double-leg stance. Pelvic belts increase sacroiliac joint motion around the sagittal axis but decrease motion around the transverse axis. With pelvic belt application, most of the strained sacroiliac joint ligaments were relieved, especially the sacrospinous, sacrotuberous, and the interosseous sacroiliac ligaments. Sacroiliac joint motion and ligament strains were minute. These results agree with validation data from other studies. Assigning homogenous and linear material properties and excluding muscle forces are clear simplifications of the complex reality. Pelvic belts alter sacroiliac joint motion and provide partial relief of ligament strain that is subjectively marked, although minimal in absolute terms. These findings confirm theories that besides being mechanical stabilizers, the sacroiliac joint ligaments are likely involved in neuromuscular feedback mechanisms. The results from our computer model help with unraveling the therapeutic mechanisms of pelvic belts.

76 FR 16641 - Petitions for Modification of Existing Mandatory Safety Standards

Science.gov (United States)

2011-03-24

...) primary belt-conveyor drives and an average of sixty (60) sprays along each of eight (8) secondary drives... Nozzle No. AA727-23 contains a recessed design to provide air escape should the nozzle be accidentally...

Investigation of a new type charging belt

International Nuclear Information System (INIS)

Jones, N.L.

1994-01-01

There are many desirable characteristics for an electrostatic accelerator charging belt. An attempt has been made to find a belt that improves on these properties over the stock belt. Results of the search, procurement, and 1,500 hours of operational experience with a substantially different belt are reported

Belt for picking up liquids

Energy Technology Data Exchange (ETDEWEB)

Sewell, R B.H.; Nelson, S P

1973-05-18

This belt for picking up liquids consists of a layer of strong material, e.g., coarse cloth, sewed on at least one layer of absorbing material, e.g., sponge cloth, the stitching being disposed along chevrons with their apexes along the central axis of the belt; the edges do not contain any other marks. This arrangement facilitates the expulsion of the absorbed liquid when the belt passes between compression rollers.

14 CFR 27.1413 - Safety belts.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Safety belts. 27.1413 Section 27.1413 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Equipment Safety Equipment § 27.1413 Safety belts. Each safety belt...

Characterization of airborne float coal dust emitted during continuous mining, longwall mining and belt transport.

Science.gov (United States)

Shahan, M R; Seaman, C E; Beck, T W; Colinet, J F; Mischler, S E

2017-09-01

Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof and ribs of mine airways. If deposited, float dust is re-entrained during a methane explosion. Without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting, which is the adding of inert material to airway surfaces, is the main control technique currently used by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, the Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section and a coal-handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation, and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8.

Granulite belts of Central India with special reference to the Bhopalpatnam Granulite Belt: Significance in crustal evolution and implications for Columbia supercontinent

Science.gov (United States)

Vansutre, Sandeep; Hari, K. R.

2010-11-01

The Central Indian collage incorporates the following major granulite belts: (1) the Balaghat-Bhandara Granulite Belt (BBG), (2) the Ramakona-Katangi Granulite Belt (RKG), (3) the Chhatuabhavna Granulite (CBG) of Bilaspur-Raigarh Belt, (4) the Makrohar Granulite Belt (MGB) of Mahakoshal supracrustals, (5) the Kondagaon Granulite Belt (KGGB), (6) the Bhopalpatnam Granulite Belt (BGB), (7) the Konta Granulite Belt (KTGB) and (8) the Karimnagar Granulite Belt (KNGB) of the East Dharwar Craton (EDC). We briefly synthesize the general geologic, petrologic and geochronologic features of these belts and explain the Precambrian crustal evolution in Central India. On the basis of the available data, a collisional relationship between Bastar craton and the EDC during the Paleo-Mesoproterozoic is reiterated as proposed by the earlier workers. The tectonic evolution of only few of the orogenic belts (BGB in particular) of Central India is related to Columbia.

Observed use of automatic seat belts in 1987 cars.

Science.gov (United States)

Williams, A F; Wells, J K; Lund, A K; Teed, N

1989-10-01

Usage of the automatic belt systems supplied by six large-volume automobile manufacturers to meet the federal requirements for automatic restraints were observed in suburban Washington, D.C., Chicago, Los Angeles, and Philadelphia. The different belt systems studied were: Ford and Toyota (motorized, nondetachable automatic shoulder belt), Nissan (motorized, detachable shoulder belt), VW and Chrysler (nonmotorized, detachable shoulder belt), and GM (nonmotorized detachable lap and shoulder belt). Use of automatic belts was significantly greater than manual belt use in otherwise comparable late-model cars for all manufacturers except Chrysler; in Chrysler cars, automatic belt use was significantly lower than manual belt use. The automatic shoulder belts provided by Ford, Nissan, Toyota, and VW increased use rates to about 90%. Because use rates were lower in Ford cars with manual belts, their increase was greater. GM cars had the smallest increase in use rates; however, lap belt use was highest in GM cars. The other manufacturers supply knee bolsters to supplement shoulder belt protection; all--except VW--also provide manual lap belts, which were used by about half of those who used the automatic shoulder belt. The results indicate that some manufacturers have been more successful than others in providing automatic belt systems that result in high use that, in turn, will mean fewer deaths and injuries in those cars.

14 CFR 31.63 - Safety belts.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Safety belts. 31.63 Section 31.63 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: MANNED FREE BALLOONS Design Construction § 31.63 Safety belts. (a) There must be a safety belt...

Lightweight, Durable Army Antennas Using Carbon Nanotube Technology

Science.gov (United States)

2013-01-01

may be adjusted by collecting the sheet on a revolving substrate conveyor belt (e.g., Teflon belt ), as shown in figure 15 (12). SEM images of the... designated by other authorized documents. Citation of manufacturer’s or trade names does not constitute an official endorsement or approval of the use...CNT) materials to produce lightweight, flexible, and durable alternatives to existing and future Army antenna designs is explored through fabrication

46 CFR 169.723 - Safety belts.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Safety belts. 169.723 Section 169.723 Shipping COAST... Control, Miscellaneous Systems, and Equipment § 169.723 Safety belts. Each vessel must carry a harness type safety belt conforming to Offshore Racing Council (ORC) standards for each person on watch or...

Innovations of Engineering Company and Competitiveness in the Mining Equipment Market

Science.gov (United States)

Pogrebnoi, Vladislav; Samorodova, Lyudmila; Shut'ko, Larisa; Yakunina, Yulia; Lyubimov, Oleg

2017-11-01

The article deals with issues related to the development of innovative projects by engineering companies and effective marketing policy as a factor of increasing their competitiveness in the mining equipment market. The paper presents the results of the development of innovative technology in the segment of extensible belt conveyors. The necessity of marketing the innovative project is proved by the example of the development of technology for the production of the motor-drum of a belt conveyor with an adjustable drive on continuous current magnets by the engineering company "Transport-Electroprivod" (LLC). The authors consider the effective marketing strategy of an engineering company as an attractor of increasing demand for innovation and competitiveness in the mining equipment market. The methods of marketing promotion and promotion of innovations are considered within the framework of the ecosystem concept of J. Moore.

Transporting, splitting and merging of atomic ensembles in a chip trap

International Nuclear Information System (INIS)

Hommelhoff, P; Haensel, W; Steinmetz, T; Haensch, T W; Reichel, J

2005-01-01

We present a toolbox for cold atom manipulation with time-dependent magnetic fields generated by an atom chip. Wire layouts, detailed experimental procedures and results are presented for the following experiments: use of a magnetic conveyor belt for positioning of cold atoms and Bose-Einstein condensates (BECs) with a potential resolution of 2 nm; splitting of thermal clouds and BECs in adjustable magnetic double-well potentials; and controlled splitting of a cold reservoir. The devices that enable these manipulations can be combined with each other. We demonstrate this by combining reservoir splitter and conveyor belt to obtain a cold atom dispenser. We discuss the importance of these devices for quantum information processing, atom interferometry and Josephson junction physics on the chip. For all devices, absorption-image video sequences are provided to demonstrate their time-dependent behaviour

Innovations of Engineering Company and Competitiveness in the Mining Equipment Market

Directory of Open Access Journals (Sweden)

Pogrebnoi Vladislav

2017-01-01

Full Text Available The article deals with issues related to the development of innovative projects by engineering companies and effective marketing policy as a factor of increasing their competitiveness in the mining equipment market. The paper presents the results of the development of innovative technology in the segment of extensible belt conveyors. The necessity of marketing the innovative project is proved by the example of the development of technology for the production of the motor-drum of a belt conveyor with an adjustable drive on continuous current magnets by the engineering company “Transport-Electroprivod” (LLC. The authors consider the effective marketing strategy of an engineering company as an attractor of increasing demand for innovation and competitiveness in the mining equipment market. The methods of marketing promotion and promotion of innovations are considered within the framework of the ecosystem concept of J. Moore.

Fast analysis of carbon content by inelastic scattering of neutrons

International Nuclear Information System (INIS)

Heinrich, B.; Irmer, K.; Poetschke, R.

1986-01-01

The direct measurement of carbon concentration of conveyor belts is a difficult problem. The great penetration depth by the fast neutrons and the 4.43 MeV γ-radiation gives an especially suitable method. The measurement were performed by the following methods: excitation of γ-radiation by a Pu-Be neutron source, excitation of γ-radiation by DT-neutron generator in stationary regime, in pulse regime, or coupled with time correlated associated particle method. Furthermore, a special Monte Carlo code in which the geometry of the measuring equipment could be specified, was written to calculate the 4.43 MeV γ counting rate for backscatter geometries and for penetration geometries. The influence of conveyor belt, of content of H, O, Fe and of mass by surface for 4.43 MeV γ-radiation was calculated for application brown coal in industry. (author)

Treadmills: a preventable source of pediatric friction burn injuries.

Science.gov (United States)

Maguiña, Pirko; Palmieri, Tina L; Greenhalgh, David G

2004-01-01

Treadmills are a burn risk for children. A child's hand can get trapped in the conveyor belt, causing friction burns to the underlying tissue. The purpose of this retrospective study was to review the characteristics and treatment of treadmill-related burns in children from 1998 to 2002. Ten patients, at a mean age of 3.4 years, sustained injuries associated with treadmill use. Trapping of the hand between the conveyor belt and the base was the most frequent injury mechanism. Burn location was predominantly on fingers and palms. Four patients required operative intervention. All patients required specialized wound care as well as scar management and occupational therapy. Treadmills pose a danger to children. Current safety devices are ineffective for preventing serious hand injuries in children. New design modifications and public awareness are needed to improve child safety.

Analytical method for establishing indentation rolling resistance

Science.gov (United States)

Gładysiewicz, Lech; Konieczna, Martyna

2018-01-01

Belt conveyors are highly reliable machines able to work in special operating conditions. Harsh environment, long distance of transporting and great mass of transported martials are cause of high energy usage. That is why research in the field of belt conveyor transportation nowadays focuses on reducing the power consumption without lowering their efficiency. In this paper, previous methods for testing rolling resistance are described, and new method designed by authors was presented. New method of testing rolling resistance is quite simple and inexpensive. Moreover it allows to conduct the experimental tests of the impact of different parameters on the value of indentation rolling resistance such as core design, cover thickness, ambient temperature, idler travel frequency, or load value as well. Finally results of tests of relationship between rolling resistance and idler travel frequency and between rolling resistance and idler travel speed was presented.

36 CFR 4.15 - Safety belts.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Safety belts. 4.15 Section 4... TRAFFIC SAFETY § 4.15 Safety belts. (a) Each operator and passenger occupying any seating position of a motor vehicle in a park area will have the safety belt or child restraint system properly fastened at...

The Conveyor Belt Problem and Newton's Third Law.

Science.gov (United States)

Stewart, Maurice Bruce

1989-01-01

Shows how the thermal power developed by friction is exactly half the supplied power in the general case of a variable force of friction. Investigates the mechanism whereby one-half the input energy is dissipated as heat using mathematical expressions. (YP)

Campylobacter jejuni survival in a poultry processing plant environment.

Science.gov (United States)

García-Sánchez, Lourdes; Melero, Beatriz; Jaime, Isabel; Hänninen, Marja-Liisa; Rossi, Mirko; Rovira, Jordi

2017-08-01

Campylobacteriosis is the most common cause of bacterial gastroenteritis worldwide. Consumption of poultry, especially chicken's meat is considered the most common route for human infection. The aim of this study was to determine if Campylobacter spp. might persist in the poultry plant environment before and after cleaning and disinfection procedures and the distribution and their genetic relatedness. During one month from a poultry plant were analyzed a total of 494 samples -defeathering machine, evisceration machine, floor, sink, conveyor belt, shackles and broiler meat- in order to isolate C. jejuni and C. coli. Results showed that C. jejuni and C. coli prevalence was 94.5% and 5.5% respectively. Different typing techniques as PFGE, MLST established seven C. jejuni genotypes. Whole genome MLST strongly suggest that highly clonal populations of C. jejuni can survive in adverse environmental conditions, even after cleaning and disinfection, and persist for longer periods than previous thought (at least 21 days) in the poultry plant environment. Even so, it might act as a source of contamination independently of the contamination level of the flock entering the slaughter line. Copyright © 2017 Elsevier Ltd. All rights reserved.

Radon daughter control in the Uravan Mineral Belt

International Nuclear Information System (INIS)

Swindle, R.W.

1977-01-01

The control of radon daughter products in mines of the Uravan Mineral Belt is strongly affected by the erratic nature of the ore deposits. Another problem is the frequent necessity of reactivating mine workings that have been inactive for many years. Ventilation holes and other airways are usually too small to provide adequate ventilation to satisfy current requirements, and they are often caved. The greatest change in ventilation systems in recent years has been the trend toward larger-diameter, drilled ventilation raises that provide more ventilation at considerably lower cost. The increase in raise size has aggrevated ground-support and ice-formation, difficulties, but these problems are being solved by lining the raises with shotcrete and grouting the water bearing horizons. Electronic air cleaners have been effectively used to remove radon daughter products from mine air for several years but their utility is limited by the rate of regrowth of the radon daughters after the air is cleaned. 5 figures

Drive alive: teen seat belt survey program.

Science.gov (United States)

Burkett, Katie M; Davidson, Steve; Cotton, Carol; Barlament, James; Loftin, Laurel; Stephens, James; Dunbar, Martin; Butterfield, Ryan

2010-08-01

To increase teen seat belt use among drivers at a rural high school by implementing the Drive Alive Pilot Program (DAPP), a theory-driven intervention built on highway safety best practices. The first component of the program was 20 observational teen seat belt surveys conducted by volunteer students in a high school parking lot over a 38-month period before and after the month-long intervention. The survey results were published in the newspaper. The second component was the use of incentives, such as gift cards, to promote teen seat belt use. The third component involved disincentives, such as increased police patrol and school policies. The fourth component was a programmatic intervention that focused on education and media coverage of the DAPP program. Eleven pre-intervention surveys and nine post-intervention surveys were conducted before and after the intervention. The pre- and post-intervention seat belt usage showed significant differences (p<0.0001). The average pre-intervention seat belt usage rate was 51.2%, while the average post-intervention rate was 74.5%. This represents a percentage point increase of 23.3 in seat belt use after the DAPP intervention. Based on seat belt observational surveys, the DAPP was effective in increasing seat belt use among rural high school teenagers. Utilizing a theory-based program that builds on existing best practices can increase the observed seat belt usage among rural high school students.

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 449 ... Vol 1, No 4 (2012), Effects of Self Esteem, Emotional Health and Social ... pop music in Nigeria for sustainable youth empowerment and development: ... Vol 1, No 1 (2012), Grassroot Sports: Conveyor Belt for Sports ...

Impact of interocean exchange on the Atlantic overturning circulation

NARCIS (Netherlands)