WorldWideScience

Sample records for converter modulator system

  1. System Aspects and Modulation Strategies of an HVDC-based Converter System for Wind Farms

    Energy Technology Data Exchange (ETDEWEB)

    Meier, Stephan

    2009-05-15

    In this thesis, a new HVDC-based converter system for wind farms is investigated. It is based on a mutually commutated soft-switching converter system and provides a unique integrated solution for the wind turbine generator drive systems, the wind turbine interconnection, and the power conversion for HVDC transmission. In a wind farm, the mutually commutated converter system is a distributed system. A medium-frequency collection grid connects the converter station, equipped with a single-phase voltage source converter and a medium-frequency transmission transformer, with the wind turbines, each containing a cyclo converter and a medium-frequency distribution transformer. In this thesis, various system aspects regarding the application of a distributed mutually commutated converter system in a wind farm are investigated. Special attention is paid to the design of a medium-frequency collection grid that has an acceptable level of transient over voltages, the design of medium-frequency transformers with suitable magnetic, electric and thermal properties, and the development of a strategy to commutate the voltage source converter during low power generation. In order to adapt the mutually commutated converter system for an application in a wind farm, it had to be further developed. Different carrier-based and space-vector oriented modulation methods have been investigated. It turns out that for any load angle there is a quasi-discontinuous pulse width modulation strategy that can produce the same pulse patterns as space vector modulation. In addition, a modulation strategy has been developed that allows to replace the IGBTs in the cyclo converter with cheap, robust, and reliable fast thyristors, despite their absence of turn-off capability. The feasibility of different modulation strategies for mutually commutated converter systems has been verified on a down-scaled prototype converter system with both IGBT- and thyristor-based cyclo converters. Finally, a feasible

  2. Space Vector Modulation Based Direct Matrix Converter for Stand-Alone system

    Directory of Open Access Journals (Sweden)

    Chandra Sekhar Ajin Sekhar

    2014-02-01

    Full Text Available In this paper Permanent Magnet Synchronous Generator (PMSG is used for wind power generation in standalone system due to their feature of high efficiency and low maintenance cost, which was fed with smart direct matrix converter for direct AC-AC conversion, It provides sinusoidal output waveforms with minimal higher order harmonics and no sub harmonics and also it eliminate the usage of dc-link and other passive elements. Space vector modulation (SVM controlled technique is used for matrix converter switching which can eliminate the switching loses by selected switching states.Proposed work are often seen as a future concept for variable speed drives technology.The  proposed model for RL load was analysed and verified by varying the resistor and inductance value and analysed using MATLAB simulation.

  3. Nonlinear Control of an Open-Loop Open-Winding Motor System with Modulated Converters

    Directory of Open Access Journals (Sweden)

    Oleschuk V.I.

    2017-04-01

    Full Text Available Purpose of this work - to provide wider control opportunities for multiphase open-end winding motor drive by modification of basic scheme of space-vector pulse-width modulation (PWM. It has been shown, that the proposed development of basic PWM scheme insures available solutions for realization of specific control dependences and modes of operation of adjustable speed ac drives with different types and kinds of loads. Suitable algorithms of PWM of converters of multiphase drive have been analyzed and compared. Extensive simulation studies have been executed for evaluation of performance and effectiveness of the proposed control strategy. Assessment of harmonic composition of the phase voltages of drive system with modified scheme of space-vector modulation has been done. Results of the executed simulations proved the fact, that the developed techniques of space-vector pulse-width modulation allow providing quarter-wave or half-wave symmetry of waveforms of the output voltage of six-phase adjustable speed drive systems during the analyzed non-standard modes and regimes of its operation.

  4. Design, status and first operations of the spallation neutron source polyphase resonant converter modulator system

    Energy Technology Data Exchange (ETDEWEB)

    Reass, W. A. (William A.); Apgar, S. E. (Sean E.); Baca, D. M. (David M.); Doss, James D.; Gonzales, J. (Jacqueline); Gribble, R. F. (Robert F.); Hardek, T. W. (Thomas W.); Lynch, M. T. (Michael T.); Rees, D. E. (Daniel E.); Tallerico, P. J. (Paul J.); Trujillo, P. B. (Pete B.); Anderson, D. E. (David E.); Heidenreich, D. A. (Dale A.); Hicks, J. D. (Jim D.); Leontiev, V. N.

    2003-01-01

    The Spallation Neutron Source (SNS) is a new 1.4 MW average power beam, 1 GeV accelerator being built at Oak Ridge National Laboratory. The accelerator requires 15 converter-modulator stations each providing between 9 and 11 MW pulses with up to a 1 .I MW average power. The converter-modulator can be described as a resonant 20 kHz polyphase boost inverter. Each converter modulator derives its buss voltage from a standard substation cast-core transformer. Each substation is followed by an SCR pre-regulator to accommodate voltage changes from no load to full load, in addition to providing a soft-start function. Energy storage is provided by self-clearing metallized hazy polypropylene traction capacitors. These capacitors do not fail short, but clear any internal anomaly. Three 'H-Bridge' IGBT transistor networks are used to generate the polyphase 20 kHz transformer primary drive waveforms. The 20 kHz drive waveforms are time-gated to generate the desired klystron pulse width. Pulse width modulation of the individual 20 lcHz pulses is utilized to provide regulated output waveforms with DSP based adaptive feedforward and feedback techniques. The boost transformer design utilizes nanocrystalline alloy that provides low core loss at design flux levels and switching frequencies. Capacitors are used on the transformer secondary networks to resonate the leakage inductance. The transformers are wound for a specific leakage inductance, not turns ratio. This design technique generates multiple secondary volts per turn as compared to the primary. With the appropriate tuning conditions, switching losses are minimized. The resonant topology has the added benefit of being deQed in a klystron fault condition, with little energy deposited in the arc. This obviates the need of crowbars or other related networks. A review of these design parameters, operational performance, production status, and OWL installation and performance to date will be presented.

  5. A Galvanically Isolated Power Converter Module for DC Zonal Electric Distribution Systems

    Science.gov (United States)

    2006-03-01

    operating at high speed. Examples of this include such weapons as a long range electromagnetic (EM) “ Railgun ” for the shore bombardment role, and the...18 3. Inductor and Capacitor Sizing .........................................................18 III. STATE SPACE MODELING...EDS Electrical Distribution System EM Electromagnetic EMALS Electromagnetic Aircraft Launch System FBC Full Bridge Converter FBI Full

  6. High power operation of the polyphase resonant converter modulator system for the spallation neutron source linear accelerator

    CERN Document Server

    Reass, W A; Baca, D M; Doss, J D; Gonzáles, J M; Gribble, R F; Trujillo, P G

    2003-01-01

    The spallation neutron source (SNS) is a new 1.4 MW average power beam, 1 GeV accelerator being built at Oak Ridge national laboratory. The accelerator requires 15 "long-pulse" converter-modulator stations each providing a maximum of 11 MW pulses with a 1.1 MW average power. Two variants of the converter-modulator are utilized, an 80 kV and a 140 kV design, the voltage dependant on the type of klystron load. The converter-modulator can be described as a resonant zero-voltage- switching polyphase boost inverter. As noted in Figure 1, each converter modulator derives its buss voltage from a standard 13.8 kV to 2100 Y (1.5 MVA) substation cast-core transformer. The substation also contains harmonic traps and filters to accommodate IEEE 519 and 141 regulations. Each substation is followed by an SCR preregulator to accommodate system voltage changes from no load to full load, in addition to providing a soft-start function. Energy storage and filtering is provided by special low inductance self-clearing metallized ...

  7. Study and Handling Methods of Power IGBT Module Failures in Power Electronic Converter Systems

    DEFF Research Database (Denmark)

    Choi, Uimin; Blaabjerg, Frede; Lee, Kyo-Beum

    2015-01-01

    and estimating the junction temperature of IGBT modules are then discussed. Subsequently, different methods for detecting open- and short-circuit faults are presented. Finally, fault-tolerant strategies for improving the reliability of power electronic systems under field operation are explained and compared...

  8. A Novel Modulation Function-Based Control of Modular Multilevel Converters for High Voltage Direct Current Transmission Systems

    Directory of Open Access Journals (Sweden)

    Majid Mehrasa

    2016-10-01

    Full Text Available In this paper, a novel modulation function-based method including analyses of the modulation index and phase is proposed for operation of modular multilevel converters (MMCs in high voltage direct current (HVDC transmission systems. The proposed modulation function-based control technique is developed based on thorough and precise analyses of all MMC voltages and currents in the a-b-c reference frame in which the alternating current (AC-side voltage is the first target to be obtained. Using the AC-side voltage, the combination of the MMC upper and lower arm voltages is achieved as the main structure of the proposed modulation function. The main contribution of this paper is to obtain two very simple new modulation functions to control MMC performance in different operating conditions. The features of the modulation function-based control technique are as follows: (1 this control technique is very simple and can be easily achieved in a-b-c reference frame without the need of using Park transformation; and (2 in addition, the inherent properties of the MMC model are considered in the proposed control technique. Considering these properties leads to constructing a control technique that is robust against MMC parameters changes and also is a very good tracking method for the components of MMC input currents. These features lead to improving the operation of MMC significantly, which can act as a rectifier in the HVDC structure. The simulation studies are conducted through MATLAB/SIMULINK software, and the results obtained verify the effectiveness of the proposed modulation function-based control technique.

  9. Reliability of Power Electronic Converter Systems

    DEFF Research Database (Denmark)

    -link capacitance in power electronic converter systems; wind turbine systems; smart control strategies for improved reliability of power electronics system; lifetime modelling; power module lifetime test and state monitoring; tools for performance and reliability analysis of power electronics systems; fault......-tolerant adjustable speed drive systems; mission profile oriented reliability design in wind turbine and photovoltaic systems; reliability of power conversion systems in photovoltaic applications; power supplies for computers; and high-power converters. Reliability of Power Electronic Converter Systems is essential...... reading for researchers, professionals and students working with power electronics and their applications, particularly those specializing in the development and application of power electronic converters and systems....

  10. Sub-module Short Circuit Fault Diagnosis in Modular Multilevel Converter Based on Wavelet Transform and Adaptive Neuro Fuzzy Inference System

    DEFF Research Database (Denmark)

    Liu, Hui; Loh, Poh Chiang; Blaabjerg, Frede

    2015-01-01

    for continuous operation and post-fault maintenance. In this article, a fault diagnosis technique is proposed for the short circuit fault in a modular multi-level converter sub-module using the wavelet transform and adaptive neuro fuzzy inference system. The fault features are extracted from output phase voltage...

  11. Generalized modular multilevel converter and modulation

    DEFF Research Database (Denmark)

    Liu, Hui; Loh, Poh Chiang; Blaabjerg, Frede

    2014-01-01

    Modular multilevel converter (MMC) has gained popularity recently with its modulation, capacitor voltage balancing and circulating current issues widely discussed. Contributing to this effort, a study is presented here to show how the MMC topology can be derived from the viewpoint of two series...... converters regulating a power grid. The generalized topology derived and notated as GMMC can then be altered to create various types of MMC, including the traditional topology that is presently well-known. This effort has not been previously discussed, and may smoothen the understanding of MMC operation...

  12. New space vector modulation technique for single-phase multilevel converters

    OpenAIRE

    León Galván, José Ignacio; Portillo Guisado, Ramón Carlos; García Franquelo, Leopoldo; Vázquez Pérez, Sergio; Carrasco Solís, Juan Manuel; Domínguez, E

    2007-01-01

    Single-phase multilevel converters are suitable for medium power applications as photovoltaic systems and switched reluctance machines. An overview of possible modulation methods including carrier-based pulse width modulation and space vector modulation techniques for multilevel single-phase converters is presented. A new space vector modulation for this type of converters is proposed. This space vector modulation method is very simple presenting low computational cost. Different solutions fo...

  13. Pulse-width modulated DC-DC power converters

    CERN Document Server

    Kazimierczuk, Marian K

    2008-01-01

    This book studies switch-mode power supplies (SMPS) in great detail. This type of converter changes an unregulated DC voltage into a high-frequency pulse-width modulated (PWM) voltage controlled by varying the duty cycle, then changes the PWM AC voltage to a regulated DC voltage at a high efficiency by rectification and filtering. Used to supply electronic circuits, this converter saves energy and space in the overall system. With concept-orientated explanations, this book offers state-of-the-art SMPS technology and promotes an understanding of the principle operations of PWM converters,

  14. Electromagnetic Compatibility of Matrix Converter System

    Directory of Open Access Journals (Sweden)

    S. Fligl

    2006-12-01

    Full Text Available The presented paper deals with matrix converters pulse width modulation strategies design with emphasis on the electromagnetic compatibility. Matrix converters provide an all-silicon solution to the problem of converting AC power from one frequency to another, offering almost all the features required of an ideal static frequency changer. They possess many advantages compared to the conventional voltage or current source inverters. A matrix converter does not require energy storage components as a bulky capacitor or an inductance in the DC-link, and enables the bi-directional power flow between the power supply and load. The most of the contemporary modulation strategies are able to provide practically sinusoidal waveforms of the input and output currents with negligible low order harmonics, and to control the input displacement factor. The perspective of matrix converters regarding EMC in comparison with other types of converters is brightly evident because it is no need to use any equipment for power factor correction and current and voltage harmonics reduction. Such converter with proper control is properly compatible both with the supply mains and with the supplied load. A special digital control system was developed for the realized experimental test bed which makes it possible to achieve greater throughput of the digital control system and its variability.

  15. Two-Stage Control Design of a Buck Converter/DC Motor System without Velocity Measurements via a Σ−Δ-Modulator

    Directory of Open Access Journals (Sweden)

    R. Silva-Ortigoza

    2013-01-01

    differential flatness property of the DC-motor model is exploited in order to propose a first-stage controller, which is designed to achieve the desired angular velocity trajectory. This controller provides the voltage profiles that must be tracked by the Buck converter. Then, a second-stage controller is meant to assure the aforementioned. This controller is based on flatness property of the Buck power converter model, which provides the input voltage to the DC motor. Due to the fact that the two-stage controller proposed uses the average model of the system, as a practical and effective implementation of this controller, a Σ − Δ-modulator is employed. Finally, in order to verify the control performance of this approach, numerical simulations are included.

  16. Liquid Metal Thermal Electric Converter bench test module

    Energy Technology Data Exchange (ETDEWEB)

    Lukens, L.L.; Andraka, C.E.; Moreno, J.B.

    1988-04-01

    This report describes the design, fabrication, and test of a Liquid Metal Thermal Electric Converter Bench Test Module. The work presented in this document was conducted as a part of Heat Engine Task of the US Department of Energy's (DOE) Solar Thermal Technology Program. The objective of this task is the development and evaluation of heat engine technologies applicable to distributed receiver systems, in particular, dish electric systems.

  17. Converters for Distributed Power Generation Systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Yang, Yongheng

    2015-01-01

    Power electronics technology has become the enabling technology for the integration of distributed power generation systems (DPGS) such as offshore wind turbine power systems and commercial photovoltaic power plants. Depending on the applications, a vast array of DPGS-based power converter...... presents an overview of the power converters for the DPGS, mainly based on wind turbine systems and photovoltaic systems, covering a wide range of applications. Moreover, the modulation schemes and interfacing power filters for the power converters are also exemplified. Finally, the general control...... topologies has been developed and more are coming into the market in order to achieve an efficient and reliable power conversion from the renewables. In addition, stringent demands from both the distribution system operators and the consumers have been imposed on the renewable-based DPGS. This article...

  18. Laser system with wavelength converter

    DEFF Research Database (Denmark)

    2012-01-01

    The present invention relates to an apparatus comprising a diode laser (10) providing radiation in a first wavelength interval, a radiation conversion unit (12) having an input and an output, the radiation converter configured to receive the radiation in the first wavelength interval from the diode...... laser at the input, the radiation conversion unit configured to convert the radiation in the first wavelength interval to radiation in a second wavelength interval and the output configured to output the converted radiation, the second wavelength interval having one end point outside the first...... wavelength interval. Further, the invention relates to a method of optically pumping a target laser (14) in a laser system, the laser system comprising a laser source providing radiation at a first frequency, the laser source being optically connected to an input of a frequency converter, the frequency...

  19. A novel loss reduced modulation strategy for matrix converters

    DEFF Research Database (Denmark)

    Helle, Lars; Munk-Nielsen, Stig

    2001-01-01

    This paper presents a new modulation strategy for three-phase to three-phase matrix converters. The new modulation strategy is applicable whenever the output voltage reference is below half the input voltage. By applying this new modulation method, the switching losses are reduced by 15......-35% compared to the conventional modulation scheme. The waveform quality of the new modulation strategy is evaluated with regard to both output flux harmonic distortion and input charge harmonic distortion....

  20. Analysis of Symmetrical Pulse Width Modulation Strategies for Matrix Converters

    DEFF Research Database (Denmark)

    Larsen, K.B.; Jorgensen, A.H.; Helle, Lars

    2002-01-01

    This paper presents a new and easy way to understand the derivation of the modulation functions for matrix converters. It is shown how the duty cycles can be calculated using techniques known from the back-to-back (B2B) voltage source inverter (VSI), thus making the subject accessible to people...... with prior knowledge in standard drives. A new modulation strategy is presented minimizing harmonic distortion compared to the standard double-sided space vector modulation for matrix converters. An improvement to an existing modulator is also presented where the proposed modification improves the harmonic...... performance. The strategies are compared both analytically and by the use of both simulations and measurements on a 12 kW matrix converter prototype.It is found that the proposed modulator has superior performance compared to modulators with equal switching frequencies and an equal number of switchings....

  1. Communication between a Matrix Converter Modulator and a Superset Regulator

    Directory of Open Access Journals (Sweden)

    P. Pošta

    2008-01-01

    Full Text Available This work deals with the modulator of a matrix converter and its communication with the superset regulator. A switching algorithm is briefly introduced. The input voltage measurement method is presented. In the last part of the paper, the testing of communication between the superset regulator and the modulator in FPGA technology are also presented. 

  2. A Fault-Tolerant Modulation Method to Counteract the Double Open-Switch Fault in Matrix Converter Drive Systems without Redundant Power Devices

    DEFF Research Database (Denmark)

    Chen, Der-Fa; Nguyen-Duy, Khiem; Liu, Tian-Hua

    2012-01-01

    redundant physical connections. It is shown that different locations of the double open switch affect the availability of the revised modulation. The steady state absolute speed error achieved with the proposed method is 4% of the nominal speed. Experimental results are performed to demonstrate the efficacy......-stage modulation is adjusted based on the knowledge of the switching logics of the inverter-stage and the operating input voltage sectors. However, the proposed fault-tolerant method does not rely on the assist of any redundant power devices or any reconfiguration of the matrix converter circuit by means of using...... of the proposed methods....

  3. Efficiency and Regulation of Commercial Low Power DC/DC Converter Modules at Low Temperatures

    Science.gov (United States)

    Elbuluk, Malik E.; Gerber, Scott; Hammoud, Ahmad; Patterson, Richard L.

    2000-01-01

    DC/DC converters that are capable of operating at cryogenic temperatures are anticipated to play an important role in the power systems of future NASA deep space missions. Design of these converters to survive cryogenic temperatures will improve the power system performance, and reduce development and launch costs. At the NASA Glenn Research Center Low Temperature Electronics Laboratory, several commercial off-the-shelf dc/dc converter modules were evaluated for their low temperature performance. Various parameters were investigated as a function of temperature, in the range of 20 C to -190 C. Data pertaining to the efficiency and voltage regulation of the tested converters is presented and discussed.

  4. Hybrid Modulation of Bidirectional Three-Phase Dual-Active-Bridge DC Converters for Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Yen-Ching Wang

    2016-06-01

    Full Text Available Bidirectional power converters for electric vehicles (EVs have received much attention recently, due to either grid-supporting requirements or emergent power supplies. This paper proposes a hybrid modulation of the three-phase dual-active bridge (3ΦDAB converter for EV charging systems. The designed hybrid modulation allows the converter to switch its modulation between phase-shifted and trapezoidal modes to increase the conversion efficiency, even under light-load conditions. The mode transition is realized in a real-time manner according to the charging or discharging current. The operation principle of the converter is analyzed in different modes and thus design considerations of the modulation are derived. A lab-scaled prototype circuit with a 48V/20Ah LiFePO4 battery is established to validate the feasibility and effectiveness.

  5. Novel electroabsorption modulator monolithically integrated with spot-size converter

    Institute of Scientific and Technical Information of China (English)

    Lianping Hou; Wei Wang; Hongliang Zhu

    2005-01-01

    @@ A novel 1.55-μm spot-size converter integrated electroabsorption modulator was designed with conventional photolithography and chemical wet etching process. A ridge double-core structure was employed for the modulator, and a buried ridge double-core structure was incorporated for the spot-size converter. The passive waveguide was optically combined with a laterally tapered active waveguide to control the mode size. The figure of merit is 4.1667 dB/V(/100μm) and the beam divergence angles in the horizontal and vertical directions were as small as 11.2° and 13.0°, respectively.

  6. Novel electroabsorption modulator monolithically integrated with spot-size converter

    Science.gov (United States)

    Hou, Lianping; Wang, Wei; Zhu, Hongliang

    2005-01-01

    A novel 1.55-?m spot-size converter integrated electroabsorption modulator was designed with conventional photolithography and chemical wet etching process. A ridge double-core structure was employed for the modulator, and a buried ridge double-core structure was incorporated for the spot-size converter. The passive waveguide was optically combined with a laterally tapered active waveguide to control the mode size. The figure of merit is 4.1667 dB/V(/100 ?m) and the beam divergence angles in the horizontal and vertical directions were as small as 11.2 deg. and 13.0 deg., respectively.

  7. Power system applications for PASC converter systems

    Energy Technology Data Exchange (ETDEWEB)

    Donnelly, M.K. [Pacific Northwest Lab., Richland, WA (United States); Johnson, R.M. [Montana State Univ., Bozeman, MT (United States)

    1994-04-01

    This paper shows, using computer EMTP simulations, some preliminary results of applying pulse amplitude synthesis and control (PASC) technology to single-source level voltage converter system. The method can be applied to any single terminal pair source with appropriate modifications in power extraction interface and computer control program to match source and load impedance characteristics. The PASC realization as discussed here employs banks of transformers, one bank per phase, in which the primaries are connected in parallel through a switch matrix to the dc source. Two opposite polarity primaries per transformer are pulsed alternatively in time to produce an oscillatory sinusoidal output waveform. PASC conversion system capabilities to produce both leading and lagging power factor power output in single-phase and three-phase {Delta} or Y configurations are illustrated. EMTP simulations are used to demonstrate the converter capabilities. Also included are discussions regarding harmonics and potential control strategies to adapt the converter to an application or to minimize harmonics.

  8. Broadband Cooperative Spectrum Sensing Based on Distributed Modulated Wideband Converter

    Directory of Open Access Journals (Sweden)

    Ziyong Xu

    2016-09-01

    Full Text Available The modulated wideband converter (MWC is a kind of sub-Nyquist sampling system which is developed from compressed sensing theory. It accomplishes highly accurate broadband sparse signal recovery by multichannel sub-Nyquist sampling sequences. However, when the number of sparse sub-bands becomes large, the amount of sampling channels increases proportionally. Besides, it is very hard to adjust the number of sampling channels when the sparsity changes, because its undersampling board is designed by a given sparsity. Such hardware cost and inconvenience are unacceptable in practical applications. This paper proposes a distributed modulated wideband converter (DMWC scheme innovatively, which regards one sensor node as one sampling channel and combines MWC technology with a broadband cooperative spectrum sensing network perfectly. Being different from the MWC scheme, DMWC takes phase shift and transmission loss into account in the input terminal, which are unavoidable in practical application. Our scheme is not only able to recover the support of broadband sparse signals quickly and accurately, but also reduces the hardware cost of the single node drastically. Theoretical analysis and numerical simulations show that phase shift has no influence on the recovery of frequency support, but transmission loss degrades the recovery performance to a different extent. Nevertheless, we can increase the amount of cooperative nodes and select satisfactory nodes by a different transmission distance to improve the recovery performance. Furthermore, we can adjust the amount of cooperative nodes flexibly when the sparsity changes. It indicates DMWC is extremely effective in the broadband cooperative spectrum sensing network.

  9. Two-Stage Control Design of a Buck Converter/DC Motor System without Velocity Measurements via a Σ−Δ-Modulator

    OpenAIRE

    R. Silva-Ortigoza; García-Sánchez, J. R.; J. M. Alba-Martínez; Hernández-Guzmán, V. M.; Marcelino-Aranda, M.; Taud, H.; Bautista-Quintero, R.

    2013-01-01

    This paper presents a two-stage control design for the “Buck power converter/DC motor” system, which allows to perform the sensorless angular velocity trajectory tracking task. The differential flatness property of the DC-motor model is exploited in order to propose a first-stage controller, which is designed to achieve the desired angular velocity trajectory. This controller provides the voltage profiles that must be tracked by the Buck converter. Then, a second-stage controller is meant to ...

  10. Mathematical simulation of the optical system of a fiber-optic measuring micro motion converter with a cylindrical lens modulation element

    Science.gov (United States)

    Murashkina, T. I.; Motin, A. V.; Badeeva, E. A.

    2017-01-01

    The paper presents the results of mathematical modeling to determine the physical, structural and technological parameters of differential fiber-optic micro motion converters with a cylindrical lens, which are basic elements of the technical solutions for fiber-optic sensors of various physical quantities used in the industry in automated control systems.

  11. Modular Multilevel Converter solutions with few Sub-Modules for wind power application

    DEFF Research Database (Denmark)

    Smirnova, Liudmila; Pyrhönen, Juha; Ma, Ke;

    2014-01-01

    Modular Multilevel Converter (MMC) is a topology where series connection of Sub-Modules (SM) is used to achieve almost sinusoidal output voltage. The MMC converter with a large number of SMs is actively used in high voltage DC (HVDC) transmission systems where a bulky converter is not a difficult...... issue. In this paper the possibility to use a MMC with just a few SMs for wind power application with limited space in the nacelle is analysed. The current loading, electrical losses and thermal performance of the power devices in the converter solutions studied are analysed. It is shown that an MMC...... converter with full-bridge (FB) SMs has a more uniform loss and temperature distribution among the semiconductor devices than an MMC with half-bridge (HB) SMs. The reliability of the MMC converters is also investigated in terms of thermal loading....

  12. Pulsewidth Modulation of Neutral-Point-Clamped Indirect Matrix Converter

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Poh Chiang, Loh; Gao, Feng

    2008-01-01

    discussed in the existing literature. Addressing the previously described issues, this paper focuses on the operational mode analysis of a three-level indirect matrix converter implemented using a neutral-point-clamped inversion stage and the design of a number of PWM and modulation ratio compensation...... schemes for controlling the converter with improved waveform quality. The performances and practicalities of the designed schemes are verified in simulation and experimentally using an implemented laboratory prototype with some representative results captured and presented in this paper....

  13. Digital Carrier Modulation and Sampling Issues of Matrix Converters

    DEFF Research Database (Denmark)

    Loh, Poh Chiang; Rong, Runjie; Blaabjerg, Frede

    2009-01-01

    digital carrier modulation schemes for controlling conventional (direct) and indirect matrix converters with minimized semiconductor commutation count and smooth sextant transitions with no erroneous states produced. For guaranteeing the latter two features, correct digital sampling instants and state...... sequence reversal must be chosen appropriately, as demonstrated in the paper for the two different topological options,which, to date, have not yet been discussed in the existing literature. To validate the concepts discussed, experimental testing on the implemented conventional and indirect matrix...

  14. Digital carrier modulation and sampling issues of matrix converters

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Loh, P.C.; Rong, R.J.

    2008-01-01

    digital carrier modulation schemes for controlling conventional and sparse matrix converters with minimized semiconductor commutation count and smooth sextant transitions with no erroneous states produced. For guaranteeing the latter two features, correct digital sampling instants and state sequence...... reversal must be chosen appropriately, as demonstrated in the paper for the two different topological options, which to date, have not yet been discussed in the existing literature. To validate the concepts discussed, experimental testing on the implemented conventional and sparse matrix laboratory...

  15. Reliability of power electronic converter systems

    CERN Document Server

    Chung, Henry Shu-hung; Blaabjerg, Frede; Pecht, Michael

    2016-01-01

    This book outlines current research into the scientific modeling, experimentation, and remedial measures for advancing the reliability, availability, system robustness, and maintainability of Power Electronic Converter Systems (PECS) at different levels of complexity.

  16. Module-Integrated Power Converters Based on Universal Dock

    Energy Technology Data Exchange (ETDEWEB)

    Chapman, Patrick; Rodriguez, Fernando

    2015-03-13

    Solar power installations using alternating current photovoltaic (ACPV) modules have significant cost and performance advantages over systems using conventional solar modules and string inverters. ACPV modules have improved energy harvest due to module-level power point tracking and redundancy. More importantly, ACPV modules are easier and cheaper to install, lowering the total installed cost, indirect costs, and barriers to market entry. Furthermore, ACPV modules have communications and data logging capability, yielding module-level telemetry data that is useful in site diagnostics and other data applications. The products of these efforts were threefold. First, an advanced microinverter power topology was developed, modeled, simulated, and tested. Second, new microinverter enclosure concepts were developed and tested. Third, a new ACPV module prototype was constructed, combining the power topology and the enclosure concepts. SolarBridge filed for patents in each of these areas and is transitioning the project from a concept phase to full development.

  17. Guiding Principles in Selecting AC To DC Converters For Power Factor Corrections in AC Transmission System

    Directory of Open Access Journals (Sweden)

    Ibekwe B.E

    2014-10-01

    Full Text Available The ac to dc converters’ power factors correction in ac transmission system were investigated. The studies include: phase-controlled converter; pulse width modulated (PWM converter and ac input current shaped converter. Using Fourier series, power factors of these converters were calculated and simulated using MATLAB. The resulting curves are displayed in the hard copies for practical guides in the choice of converters; and comparatively, current shaped type is the best.

  18. Constant Common Mode Voltage Modulation Strategy for the FB10 power converter

    DEFF Research Database (Denmark)

    Rodriguez, Pedro; Vázquez, Gerardo; Teodorescu, Remus;

    2011-01-01

    In this paper a modulation strategy based on the classical space vector modulation is applied to the FB10 converter, a new converter topology for PV applications. Firstly, the FB10 converter is presented and the natural modulation is computed. Secondly, the simulation and experimental results are...

  19. Constant Common Mode Voltage Modulation Strategy for the FB10 power converter

    DEFF Research Database (Denmark)

    Rodriguez, Pedro; Vázquez, Gerardo; Teodorescu, Remus

    2011-01-01

    In this paper a modulation strategy based on the classical space vector modulation is applied to the FB10 converter, a new converter topology for PV applications. Firstly, the FB10 converter is presented and the natural modulation is computed. Secondly, the simulation and experimental results are...

  20. Modulation of cutaneous inflammation by angiotensin-converting enzyme.

    Science.gov (United States)

    Scholzen, Thomas E; Ständer, Sonja; Riemann, Helge; Brzoska, Thomas; Luger, Thomas A

    2003-04-01

    Cutaneous neurogenic inflammation is a complex biological response of the host immune system to noxious stimuli. Present evidence suggests that zinc metalloproteases may play an important role in the regulation of neurogenic inflammation by controlling the local availability of neuropeptides, such as substance P (SP), that are capable of initiating or amplifying cutaneous inflammation after release from sensory nerves. To address the hypothesis that the dipeptidyl carboxypeptidase angiotensin-converting enzyme (ACE) is capable of modulating skin inflammation, we have analyzed murine allergic contact dermatitis (ACD) and irritant contact dermatitis (ICD) using wild-type C57BL/6J (ACE(+/+)) or genetically engineered mice with a heterozygous deletion of somatic ACE (ACE(+/-)). In 2,4-dinitro-1-fluorobenzene-sensitized ACE(+/-) mice, ACD was significantly augmented in comparison to ACE(+/+) controls as determined by the degree of ear swelling after exposure to hapten. Likewise, systemic treatment of ACE(+/+) mice with the ACE inhibitor captopril before sensitization or elicitation of ACD significantly augmented the ACD response. In contrast, local damage and neuropeptide depletion of sensory nerves following capsaicin, injection of a bradykinin B(2), or a SP receptor antagonist before sensitization significantly inhibited the augmented effector phase of ACD in mice with functionally absent ACE. However, in contrast to ACD, the response to the irritant croton oil was not significantly altered in ACE(+/-) compared with ACE(+/+) mice. Thus, ACE by degrading bradykinin and SP significantly controls cutaneous inflammatory responses to allergens but not to irritants, which may explain the frequently observed exacerbation of inflammatory skin disease in patients under medication with ACE inhibitors.

  1. Grid Connected Solar PV System with SEPIC Converter Compared with Parallel Boost Converter Based MPPT

    Directory of Open Access Journals (Sweden)

    T. Ajith Bosco Raj

    2014-01-01

    Full Text Available The main objective of this work is to study the behaviour of the solar PV systems and model the efficient Grid-connected solar power system. The DC-DC MPPT circuit using chaotic pulse width modulation has been designed to track maximum power from solar PV module. The conversion efficiency of the proposed MPPT system is increased when CPWM is used as a control scheme. This paper also proposes a simplified multilevel (seven level inverter for a grid-connected photovoltaic system. The primary goal of these systems is to increase the energy injected to the grid by keeping track of the maximum power point of the panel, by reducing the switching frequency, and by providing high reliability. The maximum power has been tracked experimentally. It is compared with parallel boost converter. Also this model is based on mathematical equations and is described through an equivalent circuit including a PV source with MPPT, a diode, a series resistor, a shunt resistor, and dual boost converter with active snubber circuit. This model can extract PV power and boost by using dual boost converter with active snubber. By using this method the overall system efficiency is improved thereby reducing the switching losses and cost.

  2. Bi-Frequency Modulated Quasi-Resonant Converters: Theory and Applications

    Science.gov (United States)

    Zhang, Yuefeng

    1995-01-01

    To avoid the variable frequency operation of quasi -resonant converters, many soft-switching PWM converters have been proposed, all of them require an auxiliary switch, which will increase the cost and complexity of the power supply system. In this thesis, a new kind of technique for quasi -resonant converters has been proposed, which is called the bi-frequency modulation technique. By operating the quasi-resonant converters at two switching frequencies, this technique enables quasi-resonant converters to achieve the soft-switching, at fixed switching frequencies, without an auxiliary switch. The steady-state analysis of four commonly used quasi-resonant converters, namely, ZVS buck, ZCS buck, ZVS boost, and ZCS boost converter has been presented. Using the concepts of equivalent sources, equivalent sinks, and resonant tank, the large signal models of these four quasi -resonant converters were developed. Based on these models, the steady-state control characteristics of BFM ZVS buck, BFM ZCS buck, BFM ZVS boost, and BFM ZCS boost converter have been derived. The functional block and design consideration of the bi-frequency controller were presented, and one of the implementations of the bi-frequency controller was given. A complete design example has been presented. Both computer simulations and experimental results have verified that the bi-frequency modulated quasi-resonant converters can achieve soft-switching, at fixed switching frequencies, without an auxiliary switch. One of the application of bi-frequency modulation technique is for EMI reduction. The basic principle of using BFM technique for EMI reduction was introduced. Based on the spectral analysis, the EMI performances of the PWM, variable-frequency, and bi-frequency modulated control signals was evaluated, and the BFM control signals show the lowest EMI emission. The bi-frequency modulated technique has also been applied to the power factor correction. A BFM zero -current switching boost converter has

  3. Design and comparative study of discrete and module-based IGBT power converters

    Indian Academy of Sciences (India)

    D VENKATRAMANAN; ANIL KUMAR ADAPA; VINOD JOHN

    2017-08-01

    This paper discusses concepts of a 20 kVA power converter design and key differences between discrete IGBT and module-based design approaches. Module-based power converters have been typically employed in academic and research institutes for power levels of 10 kVA and more. However, with advancement in IGBT technologies and the growing need to minimize system size and weight, designs based on discrete devices are now an attractive alternative for such power levels. A simple procedure is presented for power converter design that includes power loss evaluation, heat-sink thermal characterization, thermal model of overall system and sizing of DC link capacitor. Using the same, a state-of-the-art discrete device and modulebased power converters are designed. A comparison is subsequently made, where it is shown that discrete approach yields a compact and economic design up to a power level of 20 kVA. A key objective of this work is to lay emphasis on laboratory design of power converters. This enables a graduate level student to build a converter from start and in the process gain insights into the underlying engineering design aspects.

  4. Modular DC-DC converter system for energy harvesting with EAPs

    Science.gov (United States)

    Eitzen, L.; Graf, C.; Maas, J.

    2013-04-01

    Energy harvesting with EAPs requires an energy-efficient power electronics providing a bidirectional energy transfer and operating voltages of up to several kilovolts. A possibility to achieve a high energy-efficiency for high voltage conversion is the use of a modular converter system consisting of several bidirectional converter modules, which are connected in series on the converter output side and in parallel at the input side. Since each converter stage provides only a part of the overall converter output voltage, the converter module output voltages can effectively be reduced by choosing the number of cascaded converter modules appropriately. This allows the use of standard semiconductor switches with superior electrical characteristics compared to high voltage semiconductors, enabling a high energy-efficiency and smaller passive components. Since EAP devices exhibit a mainly capacitive behavior and a limitation of the operating current is required for electrode protection, the utilized converter structure/topology has to be operated as a controllable current source on the lowest control level, which is achieved by operating the converter modules of the modular converter system with a subordinate closed-looped current control scheme. In order to avoid voltage unbalances among the single converter modules, a method for voltage balancing is presented. For validation, experimental results of a realized bidirectional flyback converter prototype are presented and discussed.

  5. DC-Modulated PFC Buck-Type AC/AC Converter for Light Dimming

    Institute of Scientific and Technical Information of China (English)

    罗方林; 叶虹

    2007-01-01

    Dimmers are very widely applied in theatres, cinemas, dancing-parties, auditoriums and signal systems. They are usually supplied by single-stage AC/AC converters in the past with voltage regulation technique with the disadvantages of high total harmonic distortion, low power factor and poor power transfer efficiency. This paper introduces a novel method-DC-modulation that implements DC/DC conversion technology into AC/AC converters. The DC-modulated single-stage PFC AC/AC converters effectively improved the power factor up to 0.999 and the power transfer efficiency up to 97.8 %. The experimental results verified our design and calculation. This technique will be widely used in light dimming and other industrial applications.

  6. Application handbook for a Standardized Control Module (SCM) for DC-DC converters, volume 1

    Science.gov (United States)

    Lee, F. C.; Mahmoud, M. F.; Yu, Y.

    1980-01-01

    The standardized control module (SCM) was developed for application in the buck, boost and buck/boost DC-DC converters. The SCM used multiple feedback loops to provide improved input line and output load regulation, stable feedback control system, good dynamic transient response and adaptive compensation of the control loop for changes in open loop gain and output filter time constraints. The necessary modeling and analysis tools to aid the design engineer in the application of the SCM to DC-DC Converters were developed. The SCM functional block diagram and the different analysis techniques were examined. The average time domain analysis technique was chosen as the basic analytical tool. The power stage transfer functions were developed for the buck, boost and buck/boost converters. The analog signal and digital signal processor transfer functions were developed for the three DC-DC Converter types using the constant on time, constant off time and constant frequency control laws.

  7. Cryogenic Evaluation of an Advanced DC/DC Converter Module for Deep Space Applications

    Science.gov (United States)

    Elbuluk, Malik E.; Hammoud, Ahmad; Gerber, Scott S.; Patterson, Richard

    2003-01-01

    DC/DC converters are widely used in power management, conditioning, and control of space power systems. Deep space applications require electronics that withstand cryogenic temperature and meet a stringent radiation tolerance. In this work, the performance of an advanced, radiation-hardened (rad-hard) commercial DC/DC converter module was investigated at cryogenic temperatures. The converter was investigated in terms of its steady state and dynamic operations. The output voltage regulation, efficiency, terminal current ripple characteristics, and output voltage response to load changes were determined in the temperature range of 20 to -140 C. These parameters were obtained at various load levels and at different input voltages. The experimental procedures along with the results obtained on the investigated converter are presented and discussed.

  8. Hybrid-Circuit Module For Dc-To-Dc Power Converter

    Science.gov (United States)

    Vorperian, Vatche; Detwiler, Robert; Karmon, Dan

    1996-01-01

    Power hybrid module is general-purpose power-switching module providing flexibility in design and application. Complete dc-to-dc power converter constructed by adding input/output filters and feedback circuitry to module to suit specific application.

  9. A real time measurement of junction temperature variation in high power IGBT modules for wind power converter application

    DEFF Research Database (Denmark)

    Ghimire, Pramod; Pedersen, Kristian Bonderup; de Vega, Angel Ruiz

    2014-01-01

    This paper presents a real time measurement of on-state forward voltage and estimating the junction temperature for a high power IGBT module during a power converter operation. The power converter is realized as it can be used for a wind turbine system. The peak of the junction temperature is dec...

  10. Integrated Solar Power Converters: Wafer-Level Sub-Module Integrated DC/DC Converter

    Energy Technology Data Exchange (ETDEWEB)

    None

    2012-02-09

    Solar ADEPT Project: CU-Boulder is developing advanced power conversion components that can be integrated into individual solar panels to improve energy yields. The solar energy that is absorbed and collected by a solar panel is converted into useable energy for the grid through an electronic component called an inverter. Many large, conventional solar energy systems use one, central inverter to convert energy. CU-Boulder is integrating smaller, microinverters into individual solar panels to improve the efficiency of energy collection. The University’s microinverters rely on electrical components that direct energy at high speeds and ensure that minimal energy is lost during the conversion process—improving the overall efficiency of the power conversion process. CU-Boulder is designing its power conversion devices for use on any type of solar panel.

  11. Online Scheduling in Distributed Message Converter Systems

    NARCIS (Netherlands)

    Risse, Thomas; Wombacher, Andreas; Surridge, Mike; Taylor, Steve; Aberer, Karl

    2001-01-01

    The optimal distribution of jobs among hosts in distributed environments is an important factor to achieve high performance. The optimal strategy depends on the application. In this paper we present a new online scheduling strategy for distributed EDI converter system. The strategy is based on the B

  12. Online Scheduling in Distributed Message Converter Systems

    NARCIS (Netherlands)

    Risse, Thomas; Wombacher, Andreas; Surridge, Mike; Taylor, Steve; Aberer, Karl

    2001-01-01

    The optimal distribution of jobs among hosts in distributed environments is an important factor to achieve high performance. The optimal strategy depends on the application. In this paper we present a new online scheduling strategy for distributed EDI converter system. The strategy is based on the B

  13. Online Scheduling in Distributed Message Converter Systems

    NARCIS (Netherlands)

    Risse, Thomas; Wombacher, Andreas; Surridge, Mike; Taylor, Steve; Aberer, Karl

    The optimal distribution of jobs among hosts in distributed environments is an important factor to achieve high performance. The optimal strategy depends on the application. In this paper we present a new online scheduling strategy for distributed EDI converter system. The strategy is based on the

  14. Current Source Converter Based Wind Energy Conversion Systems

    Institute of Scientific and Technical Information of China (English)

    Samir Kouro; Jing-ya DAI; Bin WU

    2011-01-01

    The increase in the installed capacity of wind energy conversion systems (WECS) has triggered the development of more demanding grid codes and additional requirements on performance.In order to meet these requirements the industry trend has shifted to full-scale power converter interfaces in modern multi-megawatt WECS.As consequence,a wide variety of new power converter topologies and WECS configurations have been introduced in recent years.Among them,current source converter(CSC) based configurations have attracted attention due to a series of advantages like:simple structure,grid friendly waveforms,controllable power factor,and reliable grid short-circuit protection.This paper presents the latest developments in CSC interfaces for WECS and related technologies such as modulation methods,control schemes and grid code compatibility.

  15. Faults and Diagnosis Systems in Power Converters

    DEFF Research Database (Denmark)

    Lee, Kyo-Beum; Choi, Uimin

    2014-01-01

    efforts have been put into making these systems better in terms of reliability in order to achieve high power source availability, reduce the cost of energy and also increase the reliability of overall systems. Among the components used in power converters, a power device and a capacitor fault occurs most......A power converter is needed in almost all kinds of renewable energy systems and drive systems. It is used both for controlling the renewable source and for interfacing with the load, which can be grid-connected or working in standalone mode. Further, it drives the motors efficiently. Increasing...... frequently. Therefore, it is important to monitor the power device and capacitor fault to increase the reliability of power electronics. In this chapter, the diagnosis methods for power device fault will be discussed by dividing into open- and short-circuit faults. Then, the condition monitoring methods...

  16. Mass-modulation schemes for a class of wave energy converters: Experiments, models, and efficacy

    OpenAIRE

    Diamond, CA; Judge, CQ; Orazov, B; Savaş, Ö; O'Reilly, OM

    2015-01-01

    © 2015, Elsevier Ltd. All rights reserved. In a recent series of works, mass-modulation schemes have been proposed for a class of ocean wave energy converter (WEC). The goal of the schemes is to improve the energy harvesting capabilities of these devices by taking advantage of the ambient water. However this improvement comes at the cost of increased system complexity and possible impulse loadings at the instances where the mass changes. In the present work, experimental results for a pair of...

  17. A real time measurement of junction temperature variation in high power IGBT modules for wind power converter application

    DEFF Research Database (Denmark)

    Ghimire, Pramod; Pedersen, Kristian Bonderup; de Vega, Angel Ruiz;

    2014-01-01

    This paper presents a real time measurement of on-state forward voltage and estimating the junction temperature for a high power IGBT module during a power converter operation. The power converter is realized as it can be used for a wind turbine system. The peak of the junction temperature...... is decreased at higher fundamental frequency due to change in on-state time from the change in output frequency. The junction temperature is estimated using the on-state collector-emitter voltage of the IGBT module. Lower output frequency is thermally a higher stressing zone for wind power converters, hence...

  18. Unifying and generating of space vector modulation sequences for multilevel converter

    DEFF Research Database (Denmark)

    Ma, Ke; Blaabjerg, Frede

    2014-01-01

    Space Vector Modulation (SVM) is a powerful method which enables some freedom to generate the modulation sequences and modify the performances of converter. However, in the multi-level converter structures, the number of switching state redundancies significantly increases, and the determination...

  19. Development of modulation strategies for NPC converter addressing DC link voltage balancing and CMV reduction

    DEFF Research Database (Denmark)

    Boian, D.; Biris, C.; Teodorescu, Remus

    2012-01-01

    in insulation breakdown and bearing failures. By the use of this type of converters, both Electromagnetic Interference (EMI) and harmonic distortions are improved. This paper proposes two modulation strategies for Three Level Neutral Point Clamped Converter (3L-NPC). The main focus of these modulation...... strategies is to reduce the Common Mode Voltage (CMV) and balance the DC Link Voltage....

  20. A system for converting print into braille.

    Science.gov (United States)

    Blenkhorn, P

    1997-06-01

    This paper describes a method for converting text into braille, in the form in which it is stored as in a computer. The system has been designed to be configurable for a wide range of languages and character sets, and uses a predominantly table driven method to achieve this. The algorithm is explained in the context of the conversion of text into Standard English Braille (British), and the tables for this transformation are given. Particular importance has been attached to enabling braille specialists, who are not experts in computer algorithms, to be able to modify the system for either slight modifications to an existing braille code translator, or for producing a braille code translator for a new language.

  1. A highly efficient PV system using a series connection of DC-DC converter output with a photovoltaic panel

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ho-sung [Department of Electrical Engineering, Pusan National University, Jangjeon-dong, Geumjeong-gu, Busan 609-735 (Korea); New and Renewable Energy System Research Center, Korea Electro-technology Research Institute, 28-1, Sungju-dong Changwon-si, Kyungsannam-do, 641-120 (Korea); Kim, Jong-Hyun; Min, Byung-Duk; Yoo, Dong-Wook [New and Renewable Energy System Research Center, Korea Electro-technology Research Institute, 28-1, Sungju-dong Changwon-si, Kyungsannam-do, 641-120 (Korea); Kim, Hee-Je [Department of Electrical Engineering, Pusan National University, Jangjeon-dong, Geumjeong-gu, Busan 609-735 (Korea)

    2009-11-15

    A photovoltaic (PV) power conditioning system (PCS) must have high conversion efficiency and low cost. Generally, a PV PCS uses either a single string converter or a multilevel module integrated converter (MIC). Each of these approaches has both advantages and disadvantages. For a high conversion efficiency and low cost PV module, a series connection of a module integrated DC-DC converter output with a photovoltaic panel was proposed. The output voltage of the PV panel is connected to the output capacitor of the fly-back converter. Thus, the converter output voltage is added to the output voltage of the PV panel. The isolated DC-DC converter generates only the difference voltage between the PV panel voltage and the required total output voltage. This method reduces the power level of the DC-DC converter and enhances energy conversion efficiency compared with a conventional DC-DC converter. (author)

  2. A new converter for improving efficiency of multi-actuators fluid power system

    Energy Technology Data Exchange (ETDEWEB)

    Xue, Yong; Shang, JianZhong; Yang, JunHong; Wang Zhuo [National University of Defense Technology, Changsha (China)

    2016-05-15

    This paper is concerned with the application of energy efficient fluid power in mobile robots system and proposes a new fluid power converter system which is analogous to a boost converter in power electronics. The fluid power converter system is based on the principle of pulse-width modulation. The fluid power converter has an effect akin to an electrical switched inductance transformer, wherein the output pressure or flow rate can be stepped up or down. Using an inductive reactance device (an inertia mass-block), the output flow and pressure can be varied to meet the load by a means that does not rely on dissipation of power (the resistance control). The simulation model based on the mathematics models of the components is built to analyse the performance of the fluid power converter. It is clearly shown that the fluid power converter has higher energy efficiency than conventional resistance control manners.

  3. A low noise high efficiency buck DC-DC converter with sigma-delta modulation

    Energy Technology Data Exchange (ETDEWEB)

    Cai Shujiang; Pi Changming; Yan Wei; Li Wenhong, E-mail: wenhongli@fudan.edu.cn [State Key Laboratory of ASIC and Systems, Fudan University, Shanghai 201203 (China)

    2011-07-15

    Some research efforts to improve the efficiency and noise performance of buck DC-DC converters are explored. A carefully designed power MOSFET driver, including a dead time controller, discontinuous current mode (DCM) controller and gate width controller, is proposed to improve efficiency. Instead of PWM modulation, sigma-delta modulation is introduced into the feedback loop of the converter to move out the clock-referred harmonic spike. The proposed converter has been designed and fabricated by a 0.35 {mu}m CMOS process. Measured results show that the peak efficiency of the converter can reach 93% and sigma-delta modulation suppresses the harmonic spike by 30 dB over PWM modulation. (semiconductor integrated circuits)

  4. Low Temperature Performance of High Power Density DC/DC Converter Modules

    Science.gov (United States)

    Elbuluk, Malik E.; Hammond, Ahmad; Gerber, Scott; Patterson, Richard L.; Overton, Eric

    2001-01-01

    In this paper, two second-generation high power density DC/DC converter modules have been evaluated at low operating temperatures. The power rating of one converter (Module 1) was specified at 150 W with an input voltage range of 36 to 75 V and output voltage of 12 V. The other converter (Module 2) was specified at 100 W with the same input voltage range and an output voltage of 3.3 V. The converter modules were evaluated in terms of their performance as a function of operating temperature in the range of 25 to -140 C. The experimental procedures along with the experimental data obtained are presented and discussed in this paper.

  5. Control of high power IGBT modules in the active region for fast pulsed power converters

    CERN Document Server

    Cravero, J M; Garcia Retegui, R; Maestri, S; Uicich, G

    2014-01-01

    At CERN, fast pulsed power converters are used to supply trapezoidal current in different magnet loads. These converters perform output current regulation by using a high power IGBT module in its ohmic region. This paper presents a new strategy for pulsed current control applications using a specifically designed IGBT driver.

  6. Impact of modulation strategies on power devices loading for 10 MW multilevel wind power converter

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Isidori, Andrea; Rossi, Fabio Mario

    2012-01-01

    in the semiconductor devices of three-level converter adopting continuous and discontinuous PWM modulation strategies. This aspect strongly influences the operation of the converter and directly affects its efficiency. Therefore, a simulation platform is developed in Matlab/Simulink and PLECS environment to analyse...

  7. Pulse-Width-Modulation of Neutral-Point-Clamped Sparse Matrix Converter

    DEFF Research Database (Denmark)

    Loh, P.C.; Blaabjerg, Frede; Gao, F.

    2007-01-01

    literature. Addressing the afore-described issues, this paper focuses on the operational mode analysis of a three-level sparse matrix converter implemented using a neutral-point-clamped inversion stage, and  the design of a number of PWM and modulation ratio compensation schemes for controlling the converter...

  8. Reconfigurable optical quadrature amplitude modulation converter/encoder using a tunable complex coefficient optical tapped delay line.

    Science.gov (United States)

    Khaleghi, Salman; Chitgarha, Mohammad Reza; Yilmaz, Omer F; Tur, Moshe; Haney, Michael W; Langrock, Carsten; Fejer, Martin M; Willner, Alan E

    2013-05-15

    We experimentally demonstrate a reconfigurable optical converter/encoder for quadrature amplitude modulated (QAM) signals. The system utilizes nonlinear wavelength multicasting, conversion-dispersion delays, and simultaneous nonlinear multiplexing and sampling. We show baud rate tunability (31 and 20 Gbaud) and reconfigurable conversions from lower-order QAM signals to higher-order QAM signals (e.g., 64-QAM).

  9. Quasi-Periodicity and Border-Collision Bifurcations in a DC-DC Converter with Pulsewidth Modulation

    DEFF Research Database (Denmark)

    Zhusubalaliyev, Zh. T.; Soukhoterin, E.A.; Mosekilde, Erik

    2003-01-01

    The paper considers the dynamics of a dc-dc converter with pulsewidth modulation. The typical scenario for the transition to chaos in such systems proceeds via quasi-periodicity, resonance cycles, and torus destruction. Detailed bifurcation analysis shows that the resonance solutions arise via...

  10. Comparison of three different Modulators for Power Converters with Respect to EMI Optimization

    DEFF Research Database (Denmark)

    Knott, Arnold; Pfaffinger, Gerhard; Andersen, Michael Andreas E.

    2008-01-01

    Switch-mode Power Converters are well known for emissions in the band of electromagnetic interference (EMI) interest. The spectrum shape depends on the type of modulator and its purpose. This paper gives design guidelines to choose the optimum topology depending on requirements of different...... applications. Spectral measurements on prototypes of a pulse width modulator (PWM), a -modulator and a hysteretic self-oscillating modulator are shown, which are verifying their simulations, with respect to different EMI challenges....

  11. Grid Converters for Photovoltaic and Wind Power Systems

    DEFF Research Database (Denmark)

    Teodorescu, Remus; Liserre, Marco; Rodriguez, Pedro

    power, operation within a wide range of voltage and frequency, voltage ride-through capability, reactive current injection during faults, grid services support. This book explains the topologies, modulation and control of grid converters for both photovoltaic and wind power applications. In addition...... to power electronics, this book focuses on the specific applications in photovoltaic wind power systems where grid condition is an essential factor. With a review of the most recent grid requirements for photovoltaic and wind power systems, the book discusses these other relevant issues: Modern grid...... inverter topologies for photovoltaic and wind turbines Islanding detection methods for photovoltaic systems Synchronization techniques based on second order generalized integrators (SOGI) Advanced synchronization techniques with robust operation under grid unbalance condition grid filter design and active...

  12. Planar Integrated Magnetics (PIM) Module in Hybrid Bidirectional DC-DC Converter for Fuel Cell Application

    DEFF Research Database (Denmark)

    Ouyang, Ziwei; Zhang, Zhe; Thomsen, Ole Cornelius

    2011-01-01

    , hereby increasing the power density of converters. In this paper, a new planar integrated magnetics (PIM) module for a phase-shift plus duty cycle controlled hybrid bi-directional dc-dc converter is proposed, which assembles one boost inductor and two transformers into an E-I-E core geometry, reducing...... and theoretical analysis, a lab prototype employing the PIM module is implemented for a fuel cell application with 20~40 V input voltage and 400 V output voltage. Detailed results from the experimental comparisons demonstrate that the PIM module is fully functional and electromagnetically equivalent...

  13. Investigation and improvement of high step- up converters for pv module applications

    Directory of Open Access Journals (Sweden)

    Hamed moradmand jazi

    2017-01-01

    Full Text Available sun is of the clean and cheapest sources of energy. Charging slight energy to electricity is carried out by PV modules. Since most electric consumers need Ac input voltage, the PV modules output voltage should be changed into Ac form. But, the voltage level of PV modules is much lower than the voltage needed in input stage of inverters. Because of large voltage level. Difference it is not possible to use the basic boost and buck-boost converters. The basic boost and buck-boost converters definitely can not be used in this applications, for, they will face extreme drop in efficiency in duty cycles closer to unity. In this paper The proposed converter is presented in order to decrease the voltage stress of coupled inductors based high step-up converters. The voltage stress in the proposed converter is lower than the high step-up boost converter with coupled inductors in identical condition. Also, soft switching condition for switches and diodes is realized by active clamp circuit, and with this technique and proper selection of duty cycle, large gain and high efficiency could be achieved ultimately. . In this paper theoretical analysis is used for analyzing the performance of the proposed converters, and in order to verify the theoretical analysis, simulated results from pspice software is provides.

  14. Equalization Technique for Balancing the Modulation Ratio Characteristics of the Single-Phase-to-Three-Phase Matrix Converter

    Directory of Open Access Journals (Sweden)

    Vengadeshwaran Velu

    2016-01-01

    Full Text Available Three-phase system has numerous advantages over the single-phase system in terms of instantaneous power, stability, and cost. Three-phase systems are not available in every location particularly in remote rural areas, hill stations, low voltage distribution homes, and so forth. Having a system that is capable of converting directly the readily available single-phase system to three phases will have greater usability in various applications. The routine techniques adopted in the direct ac-ac single-phase-to-three-phase converters do not yield the best desired outputs because of their complexity in the segregation process and bidirectional nature of the input signal. Other initiatives use ac-dc-ac converters which are huge and costly due to dc link energy storage devices. Further, none of these systems provide a convincing result in producing the standard three-phase output voltages that are 120° away from each other. This paper proposes an effective direct ac-ac single-phase-to-three-phase conversion technique based on space vector pulse width modulation based matrix converter system that produces a convincing three-phase output signals from a single-phase source with balanced modulation index characteristics. The details of the scientific programming adopted on the proposed technique were presented.

  15. Evaluation of Modulation Schemes for Three-Phase to Three-Phase Matrix Converters

    DEFF Research Database (Denmark)

    Helle, Lars; Larsen, Kim B.; Joergensen, Allan Holm

    2004-01-01

    This paper presents a method for evaluating different modulation schemes employed with three-phase to three-phase matrix converters. The evaluation method addresses three important modulator characteristics: the output waveform quality, the input waveform quality and the switching losses associated...... on the output load angle. This new modulation approach is applicable whenever the output voltage reference is below half the input voltage, and the output voltage quality is then superior to that of the conventional space vector modulation scheme. The functionality of the new modulation scheme is validated...

  16. Multifunctional Converter Drive for Automotive Electric Power Steering Systems

    NARCIS (Netherlands)

    Hackner, T.J.

    2013-01-01

    In this thesis it is shown that in the case of an automotive electric power steering system, critical pulse power loads can be decoupled from the power net with a storage element and a multifunctional converter. A multifunctional converter system is proposed because it uses the motor drive system as

  17. A Two-stage DC-DC Converter for the Fuel Cell-Supercapacitor Hybrid System

    DEFF Research Database (Denmark)

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

    2009-01-01

    A wide input range multi-stage converter is proposed with the fuel cells and supercapacitors as a hybrid system. The front-end two-phase boost converter is used to optimize the output power and to reduce the current ripple of fuel cells. The supercapacitor power module is connected by push......-pull-forward half bridge (PPFHB) converter with coupled inductors in the second stage to handle the slow transient response of the fuel cells and realize the bidirectional power flow control. Moreover, this cascaded structure simplifies the power management. The control strategy for the whole system is analyzed...

  18. Predictive Trailing-Edge Modulation Average Current Control in DC-DC Converters

    Directory of Open Access Journals (Sweden)

    LASCU, D.

    2013-11-01

    Full Text Available The paper investigates predictive digital average current control (PDACC in dc/dc converters using trailing-edge modulation (TEM. The study is focused on the recurrence duty cycle equation and then stability analysis is performed. It is demonstrated that average current control using trailing-edge modulation is stable on the whole range of the duty cycle and thus design problems are highly reduced. The analysis is carried out in a general manner, independent of converter topology and therefore the results can then be easily applied for a certain converter (buck, boost, buck-boost, etc.. The theoretical considerations are confirmed for a boost converter first using the MATLAB program based on state-space equations and finally with the CASPOC circuit simulation package.

  19. Power electronics converters for wind turbine systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Liserre, Marco; Ma, Ke

    2011-01-01

    The steady growth of installed wind power which reached 200 GW capacity in 2010, together with the up-scaling of the single wind turbine power capability - 7 MW’s has been announced by manufacturers - has pushed the research and development of power converters towards full scale power conversion,...

  20. Power Electronics Converters for Wind Turbine Systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Liserre, Marco; Ma, Ke

    2012-01-01

    The steady growth of installed wind power together with the upscaling of the single wind turbine power capability has pushed the research and development of power converters toward full-scale power conversion, lowered cost pr kW, increased power density, and also the need for higher reliability. ...

  1. Power electronics converters for wind turbine systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Liserre, Marco; Ma, Ke

    2011-01-01

    The steady growth of installed wind power which reached 200 GW capacity in 2010, together with the up-scaling of the single wind turbine power capability - 7 MW’s has been announced by manufacturers - has pushed the research and development of power converters towards full scale power conversion,...

  2. Progress on the 140 KV, 10 Megawatt Peak, 1 Megawatt Average Polyphase Quasi-Resonant Bridge, Boost Converter/Modulator for the Spallation Neutron Source (SNS) Klystron Power System

    CERN Document Server

    Reass, W A; Gribble, R F; Lynch, M T; Tallerico, P J; Reass, William A.; Doss, James D.; Gribble, Robert F.; Lynch, Michael T.; Tallerico, Paul J.

    2000-01-01

    This paper describes electrical design and operational characteristics of a zero-voltage-switching 20 kHz polyphase bridge, boost converter/modulator for klystron pulse application. The DC-DC converter derives the buss voltages from a standard 13.8 kV to 2300 Y substation cast-core transformer. Energy storage and filtering is provided by self-clearing metallized hazy polypropylene traction capacitors. Three "H-Bridge" IGBT switching networks are used to generate the polyphase 20 kHz transformers primary drive waveforms. The 20 kHz drive waveforms are chirped the appropriate duration to generate the desired klystron pulse width. PWM (pulse width modulation) of the individual 20 kHz pulses is utilized to provide regulated output waveforms with adaptive feedforward and feedback techniques. The boost transformer design utilizes amorphous nanocrystalline material that provides the required low core loss at design flux levels and switching frequencies. Resonant shunt peaking is used on the transformer secondary to ...

  3. Modulation Schemes for Single-Phase B6 Converters With Two Asymmetrical Terminal Voltages

    DEFF Research Database (Denmark)

    Qin, Zian; Loh, Poh Chiang; Blaabjerg, Frede

    2016-01-01

    B6 converter uses six switches divided equally among three phase-legs. It has commonly been used as a three-phase rectifier or inverter, mostly under balanced conditions. Three-phase conversion is however not the only area, where B6 converter has been used. The same topology has been tried...... asymmetrical. How these asymmetrical references should be formulated to meet various performance specifications of a single-phase B6 converter is the theme of this paper. Simulation and experimental results have been obtained for verifying the modulation schemes proposed....

  4. Grid Converters for Stationary Battery Energy Storage Systems

    DEFF Research Database (Denmark)

    Trintis, Ionut

    to hours, rated at MW and MWh, battery energy storage systems are suitable and ecient solutions. Grid connection of the storage system can be done at dierent voltage levels, depending on the location and application scenario. For high power and energy ratings, increase in the battery and converter voltage...... was realized for a 100 kW active rectier to be used in a 6 kV battery energy storage test bench. In the second part, dierent solutions for power converters to interface energy storage units to medium voltage grid are given. A new modular multilevel converter concept is introduced, where the energy storage......-voltage 100 kW bidirectional grid converter, to be used in a high voltage battery energy storage test bench. The control structure proved to be stable without damping. The converter was tested in the test bench and the experimental results are presented. Multilevel converters are replacing the classical two...

  5. High Performance Control of Matrix Converter Fed Induction Motor Drive System

    Institute of Scientific and Technical Information of China (English)

    孙凯; 黄立培; MATSUSE Kouki

    2007-01-01

    Matrix converter fed motor drive is superior to pulse width modulation inverter drives since it not only provides bi-directional power flow, sinusoidal input/output currents, unity input power factor, but also allows a compact design due to the lack of DC-link capacitors for energy storage. In this paper, model and control of matrix converter fed induction motor drive system are analyzed. A combined control strategy is simplified and improved, which realizes space vector pulse width modulation of matrix converter and rotor flux oriented vector control technique for induction motor drive simultaneously. This control strategy combines the advantages of matrix converter with the good drive performance of vector control technique. Experimental results demonstrate the feasibility and effectiveness of the proposed control strategy.

  6. High Efficiency Bi-Directional Converter Used For Renewable System

    Directory of Open Access Journals (Sweden)

    M. Desal Raja

    2014-02-01

    Full Text Available This paper presents an Isolated bi-directional converter for renewable system. Voltage stress and current stress was decreses in switches. Power flows in both side. The proposed converter three phase ac voltage to dc voltage, dc voltage to three phase a.c voltage and synchronous the two voltage source. Silicon carbide diodes and bi-directional switches Mosfet’s are used for decreases the switching loss. LC Series resonant converter connected to the high efficiency. This converter power conversion control by the output voltage information.

  7. Concept Study of Foundation Systems for Wave Energy Converters

    DEFF Research Database (Denmark)

    Molina, Salvador Devant; Vaitkunaite, Evelina; Ibsen, Lars Bo

    Analysis of possible foundation solution for Wave Energy Converters (WEC) is presented by investigating and optimizing novel foundation systems recently developed for offshore wind turbines. Gravity based, pile and bucket foundations are innovative foundation systems that are analyzed. Concept...

  8. Phase-modulated shaping of narrowband type-I parametric down-converted photons

    CERN Document Server

    Joseph1, A T; Pike2, E R; Sarkar2, S

    2006-01-01

    We present a general theoretical description of the temporal shaping of narrowband noncollinear type-I down-converted photons using a spectral phase filter with a symmetric phase distribution. By manipulating the spectral phase of the signal or idler photon, we demonstrate control of the correlation time and shape of the two-photon wave function with modulation frequency and modulation depth of the phase distribution.

  9. Full Space Vectors Modulation for Nine-Switch Converters Including CF & DF Modes

    DEFF Research Database (Denmark)

    Dehghan Dehnavi, Seyed Mohammad; Mohamadian, Mustafa; Andersen, Michael A. E.

    2010-01-01

    converter. As a space vector modulation for DF mode has already been proposed by authors. This paper proposes a full space vector modulation (SVM) for both CF and DF modes. Also practical methods are presented for SVM proposed. In addition a special SVM is proposed that offers minimum total harmonic...... distortion (THD) in DF mode. The performance of the proposed SVM is verified by simulation results....

  10. Carrier-based modulation schemes for various three-level matrix converters

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Loh, P.C.; Rong, R.C.;

    2008-01-01

    Matrix converters with three-level phase switching and five-level line switching characteristics have recently been proposed as improved ldquoall semiconductorrdquo ac-ac power processors. For their control, different modulation schemes have also been developed with different researchers claiming...... be implemented on a single common hardware platform....

  11. Low-Loss 256-Channel AWG Module with Monolithically Integrated Spot-Size Converters

    Institute of Scientific and Technical Information of China (English)

    M. Itoh; S. Kamei; M. Ishii; Y. Hida; T. Shibata; Y. Hibino

    2003-01-01

    We developed a compact fiber-pigtailed 256-channel AWG module with 1.5% △ waveguides.By monolithically integrating spot-size converters with input/output waveguides, we achieved a lowinsertion loss of 2.6-4.1 dB with a low background crosstalk of -40 dB.

  12. Low-Loss 256-Channel AWG Module with Monolithically Integrated Spot-Size Converters

    Institute of Scientific and Technical Information of China (English)

    M.; Itoh; S.; Kamei; M.; Ishii; Y.; Hida; T.; Shibata; Y.; Hibino

    2003-01-01

    We developed a compact fiber-pigtailed 256-channel AWG module with 1.5% A waveguides. By monolithically integrating spot-size converters with input/output waveguides, we achieved a low insertion loss of 2.6-4.1 dB with a low background crosstalk of-40 dB.

  13. Low Power Penalty Operation of a Wide Input Dynamic Range Cross-Phase Modulation Wavelength Converter

    Institute of Scientific and Technical Information of China (English)

    Jun; Endo; Akira; Ohki; Rieko; Sato; Toshio; Ito; Yuichi; Tohmori; Yasuhiro; Suzuki

    2003-01-01

    We successfully demonstrated low power penalty operation of a cross-phase modulated (XPM) wavelength converter using a semiconductor optical amplifier (SOA) power equalizer. We also clarified the SOA equalizing level for more adaptive wavelength conversion and achieved a power penalty of less than 1 dB over the wide input dynamic range of 15 dB.

  14. The Application of Stationary VOC-PR with PLL for Grid side Converter-based Wind Power Generation System

    DEFF Research Database (Denmark)

    Guo, Yougui; Zeng, Ping; Li, Lijuan

    2010-01-01

    Voltage oriented control PR is combined with space vector modulation and phase locked loop to control the grid side converter in wind power generation system in this paper. First the mathematical models of grid side converter and LCL filter as well as grid are given. Then the control strategy of ...

  15. Photovoltaic Energy Conversion System Constructed by High Step-Up Converter with Hybrid Maximum Power Point Tracking

    OpenAIRE

    Hwu, K. I.; Tu, W. C.; Wang, C.R.

    2013-01-01

    A photovoltaic energy conversion system, constructed by high step-up converter with hybrid maximum power point tracking (HMPPT), is presented. A voltage converter with a high voltage conversion ratio is proposed, which is simple in circuit and easy in control. After this, such a converter operating with a suitable initial duty cycle of the pulsewidth-modulated (PWM) control signal, together with the proposed HMPPT algorithm combining the fractional open-circuit voltage method and the incremen...

  16. A novel Modulation Topology for Power Converters utilizing Multiple Carrier Signals

    DEFF Research Database (Denmark)

    Knott, Arnold; Pfaffinger, Gerhard; Andersen, Michael Andreas E.

    2008-01-01

    Power converters are known to generate spectral components in the range of interest of electromagnetic compatibility measurements. Common approaches to manipulate some selected components in these frequency ranges are shown here. These approaches add components to the input signal of the modulator...... to derive a slightly varied spectrum. To achieve a rectangular output signal, those modulators use a triangular or saw tooth carrier signal. A novel family of modulators is shown here, using more than one carrier signal to obtain a completely changed spectrum while maintaining the rectangular shaped...... waveform at the output. The multiple carriers are fed into multiple comparators and their outputs are intelligently combined by logic gates to get a single signal to drive one power stage of any type of converter. This commutation distinguishes between the four members of the novel family: the first one...

  17. Electroabsorption-modulated DFB laser integrated with dual-waveguide spot-size converter

    Science.gov (United States)

    Hou, Lianping; Wang, Wei; Zhu, Hongliang; Wang, Baojun; Zhou, Fan

    2005-11-01

    A 1.55-μm ridge DFB laser and electroabsorption modulator monolithically integrated with a buried-ridge-stripe dual-waveguide spot-size converter at the output port for low-loss coupling to a cleaved single-mode optical fiber was fabricated by means of selective area growth, quantum well intermixing and dual-core technologies. These devices exhibit threshold current of 28 mA, side mode suppression ratio of 38.0 dB, 3-dB modulation bandwidth of 12.0 GHz, modulator extinction ratios of 25.0 dB dc. The output beam divergence angles of the spot-size converter in the horizontal and vertical directions are as small as 8.0°×12.6°, respectively, resulting in 3.2 dB coupling loss with a cleaved single-mode optical fiber.

  18. Two Level Versus Matrix Converters Performance in Wind Energy Conversion Systems Employing DFIG

    Science.gov (United States)

    Reddy, Gongati Pandu Ranga; Kumar, M. Vijaya

    2017-05-01

    Wind power capacity has received enormous growth during past decades. With substantial development of wind power, it is expected to provide a fifth of world's electricity by the end of 2030. In wind energy conversion system, the power electronic converters play an important role. This paper presents the two level and matrix converters performance in wind energy conversion system employing Doubly Fed Induction Generator (DFIG). The DFIG is a wound rotor induction generator. Because of the advantages of the DFIG over other generators it is being used for most of the wind applications. This paper also discusses control of converters using the space vector pulse width modulation technique. The MATLAB/SIMULINK ® software is used to study the performance of the converters.

  19. Power electronic converters and systems frontiers and applications

    CERN Document Server

    Trzynadlowski, Andrzej M

    2016-01-01

    Power electronics is a branch of electrical engineering dealing with conversion and control of electric power using semiconductor power switches. This book provides an overview of modern power electronic converters and systems, and their applications.

  20. The New Modular Control System for Power Converters at CERN

    CERN Document Server

    Di Cosmo, Matteo

    2015-01-01

    The CERN accelerator complex consists of several generations of particle accelerators, with around 5000 power converters supplying regulated current and voltage to normal and superconducting magnet circuits. Today around 12 generations of converter control platforms can be found in the accelerator complex, ranging in age and technology. The diversity of these platforms has a significant impact on operability, maintenance and support of power converters. Over the past few years a new generation of modular controls called RegFGC3 has been developed by CERN’s power conversion group, with a goal to provide a standardised control platform, supporting a wide variety of converter topologies. The aim of this project is to reduce maintenance costs by decreasing the variety and diversity of control systems whilst simultaneously improving the operability and reliability of power converters and their controls. This paper describes the state of the on-going design and realization of the RegFGC3 platform, focusing on fun...

  1. Laboratory manual for pulse-width modulated DC-DC power converters

    CERN Document Server

    Kazimierczuk, Marian K

    2015-01-01

    Designed to complement a range of power electronics study resources, this unique lab manual helps students to gain a deep understanding of the operation, modeling, analysis, design, and performance of pulse-width modulated (PWM) DC-DC power converters.  Exercises focus on three essential areas of power electronics: open-loop power stages; small-signal modeling, design of feedback loops and PWM DC-DC converter control schemes; and semiconductor devices such as silicon, silicon carbide and gallium nitride. Meeting the standards required by industrial employers, the lab manual combines program

  2. Soft Computing Module of High Step-Up DC–DC Converter for PV Module using Simulink Environment

    Directory of Open Access Journals (Sweden)

    K. Vinoth Kumar

    2012-12-01

    Full Text Available Within the photovoltaic (PV power-generation market, the  PV module has shown obvious growth. However, a high voltage gain converter is essential for the module’s grid connection through a dc–ac inverter. This paper proposes a converter that employs a floating active switch to isolate energy from the PV panel when the ac module is OFF; this particular design protects installers and users from electrical hazards. Without extreme duty ratios and the numerous turns-ratios of a coupled inductor, this converter achieves a high step-up voltage-conversion ratio; the leakage inductor energy of the coupled inductor is efficiently recycled to the load. These features explain the module’s high-efficiency performance. The detailed operating principles and steady-state analyses of continuous, discontinuous, and boundary conduction modes are described. A 15V input voltage, 200V output voltage, and 100W output power prototype circuit of the proposed converter has been implemented; its maximum efficiency is up to 95.3% and full-load efficiency is 92.3%.

  3. Model predictive control of bidirectional isolated DC-DC converter for energy conversion system

    Science.gov (United States)

    Akter, Parvez; Uddin, Muslem; Mekhilef, Saad; Tan, Nadia Mei Lin; Akagi, Hirofumi

    2015-08-01

    Model predictive control (MPC) is a powerful and emerging control algorithm in the field of power converters and energy conversion systems. This paper proposes a model predictive algorithm to control the power flow between the high-voltage and low-voltage DC buses of a bidirectional isolated full-bridge DC-DC converter. The predictive control algorithm utilises the discrete nature of the power converters and predicts the future nature of the system, which are compared with the references to calculate the cost function. The switching state that minimises the cost function is selected for firing the converter in the next sampling time period. The proposed MPC bidirectional DC-DC converter is simulated with MATLAB/Simulink and further verified with a 2.5 kW experimental configuration. Both the simulation and experimental results confirm that the proposed MPC algorithm of the DC-DC converter reduces reactive power by avoiding the phase shift between primary and secondary sides of the high-frequency transformer and allow power transfer with unity power factor. Finally, an efficiency comparison is performed between the MPC and dual-phase-shift-based pulse-width modulation controlled DC-DC converter which ensures the effectiveness of the MPC controller.

  4. A Scalable Module System

    CERN Document Server

    Rabe, Florian

    2011-01-01

    Symbolic and logic computation systems ranging from computer algebra systems to theorem provers are finding their way into science, technology, mathematics and engineering. But such systems rely on explicitly or implicitly represented mathematical knowledge that needs to be managed to use such systems effectively. While mathematical knowledge management (MKM) "in the small" is well-studied, scaling up to large, highly interconnected corpora remains difficult. We hold that in order to realize MKM "in the large", we need representation languages and software architectures that are designed systematically with large-scale processing in mind. Therefore, we have designed and implemented the MMT language -- a module system for mathematical theories. MMT is designed as the simplest possible language that combines a module system, a foundationally uncommitted formal semantics, and web-scalable implementations. Due to a careful choice of representational primitives, MMT allows us to integrate existing representation l...

  5. New generation polyphase resonant converter-modulators for the Korean atomic energy research institute

    Energy Technology Data Exchange (ETDEWEB)

    Reass, William A [Los Alamos National Laboratory; Baca, David M [Los Alamos National Laboratory; Gribble, Robert F [Los Alamos National Laboratory

    2009-01-01

    This paper will present operational data and performance parameters of the newest generation polyphase resonant high voltage converter modulator (HVCM) as developed and delivered to the KAERI 100 MeV ''PEFP'' accelerator [1]. The KAERI design realizes improvements from the SNS and SLAC designs [2]. To improve the IGBT switching performance at 20 kHz for the KAERI system, the HVCM utilizes the typical zero-voltage-switching (ZVS) at turn on and as well as artificial zero-current-switching (ZCS) at turn-off. The new technique of artificial ZCS technique should result in a 6 fold reduction of IGBT switching losses (3). This improves the HCVM conversion efficiency to better than 95% at full average power, which is 500 kW for the KAERI two klystron 105 kV, 50 A application. The artificial ZCS is accomplished by placing a resonant RLC circuit across the input busswork to the resonant boost transformer. This secondary resonant circuit provides a damped ''kick-back'' to assist in IGBT commutation. As the transformer input busswork is extremely low inductance (< 10 nH), the single RLC network acts like it is across each of the four IGBT collector-emitter terminals of the H-bridge switching network. We will review these topological improvements and the overall system as delivered to the KAERI accelerator and provide details of the operational results.

  6. A power conditioning system for thermoelectric generator based on interleaved Boost converter with MPPT control

    DEFF Research Database (Denmark)

    Ni, L.-X; Sun, K.; Zhang, L.

    2011-01-01

    The thermoelectric generation (TEG) system has its special charactristics of high stablility, low voltage and high current output, which is different from PV modules. The power conditioning system and control schemes used in PV applications cannot be directly applied to TEG applications. A power...... conditioning system for TEG based on interleaved Boost converter with maximum power point tracking (MPPT) control is investigated in this paper. Since an internal resistance exists inside TEG modules, an improved perturbation and observation (P&O) MPPT control scheme with power limit is proposed to extract...... maximum power from TEG by matching the load with internal resistance. Since the battery is usually employed as the load for TEG systems, the interleaved Boost converter operates in two different modes for battery charging: before the battery is fully charged, the system outputs the maximum power (MPPT...

  7. Controlling DC-DC converters by chaos-based pulse width modulation to reduce EMI

    Energy Technology Data Exchange (ETDEWEB)

    Li Hong [Department of Mathematics and Computer Science, FernUniversitaet in Hagen, 58084 Hagen (Germany)], E-mail: hong.li@FernUni-Hagen.de; Zhang Bo [School of Electric Power, South China University of Technology, Guangzhou (China); Li Zhong; Halang, Wolfgang A. [Department of Mathematics and Computer Science, FernUniversitaet in Hagen, 58084 Hagen (Germany); Chen Guanrong [Department of Electronic Engineering, City University of Hong Kong, Hong Kong (China)

    2009-11-15

    In this paper, periodic and chaotic behaviors of DC-DC converters under certain parametric conditions are simulated, experimentally verified, and analyzed. Motivated by the work of J.H.B. Deane and D.C. Hamill in 1996, where chaotic phenomena are useful in suppressing electromagnetic interference (EMI) by adjusting the parameters of the DC-DC converter and making it operate in chaos, a chaos-based pulse width modulation (CPWM) is proposed to distribute the harmonics of the DC-DC converters continuously and evenly over a wide frequency range, thereby reducing the EMI. The output waves and spectral properties of the EMI are simulated and analyzed as the carrier frequency or amplitude changes with regard to different chaotic maps. Simulation and experimental results are given to illustrate the effectiveness of the proposed CPWM, which provides a good example of applying chaos theory in engineering practice.

  8. SWITCH MODE PULSE WIDTH MODULATED DC-DC CONVERTER WITH MULTIPLE POWER TRANSFORMERS

    DEFF Research Database (Denmark)

    2009-01-01

    A switch mode pulse width modulated DC-DC power converter comprises at least one first electronic circuit on a input side (1) and a second electronic circuit on a output side (2). The input side (1) and the output side (2) are coupled via at least two power transformers (T1, T2). Each power...... transformer (T1, T2) comprises a first winding (T1a, T2a) arranged in a input side converter stage (3, 4) on the input side (1) and a second winding (T1 b, T2b) arranged in a output side converter stage (5) on the output side (2), and each of the windings (T1a, T1 b, T2a, T2b) has a first end and a second end...

  9. AC Voltage Control of DC/DC Converters Based on Modular Multilevel Converters in Multi-Terminal High-Voltage Direct Current Transmission Systems

    Directory of Open Access Journals (Sweden)

    Rui Li

    2016-12-01

    Full Text Available The AC voltage control of a DC/DC converter based on the modular multilevel converter (MMC is considered under normal operation and during a local DC fault. By actively setting the AC voltage according to the two DC voltages of the DC/DC converter, the modulation index can be near unity, and the DC voltage is effectively utilized to output higher AC voltage. This significantly decreases submodule (SM capacitance and conduction losses of the DC/DC converter, yielding reduced capital cost, volume, and higher efficiency. Additionally, the AC voltage is limited in the controllable range of both the MMCs in the DC/DC converter; thus, over-modulation and uncontrolled currents are actively avoided. The AC voltage control of the DC/DC converter during local DC faults, i.e., standby operation, is also proposed, where only the MMC connected on the faulty cable is blocked, while the other MMC remains operational with zero AC voltage output. Thus, the capacitor voltages can be regulated at the rated value and the decrease of the SM capacitor voltages after the blocking of the DC/DC converter is avoided. Moreover, the fault can still be isolated as quickly as the conventional approach, where both MMCs are blocked and the DC/DC converter is not exposed to the risk of overcurrent. The proposed AC voltage control strategy is assessed in a three-terminal high-voltage direct current (HVDC system incorporating a DC/DC converter, and the simulation results confirm its feasibility.

  10. The BepiColombo Laser Altimeter (BeLA) power converter module (PCM): Concept and characterisation

    Science.gov (United States)

    Rodrigo, J.; Gasquet, E.; Castro, J.-M.; Herranz, M.; Lara, L.-M.; Muñoz, M.; Simon, A.; Behnke, T.; Thomas, N.

    2017-03-01

    This paper presents the principal considerations when designing DC-DC converters for space instruments, in particular for the power converter module as part of the first European space laser altimeter: "BepiColombo Laser Altimeter" on board the European Space Agency-Japan Aerospace Exploration Agency (JAXA) mission BepiColombo. The main factors which determine the design of the DC-DC modules in space applications are printed circuit board occupation, mass, DC-DC converter efficiency, and environmental-survivability constraints. Topics included in the appropriated DC-DC converter design flow are hereby described. The topology and technology for the primary and secondary stages, input filters, transformer design, and peripheral components are discussed. Component selection and design trade-offs are described. Grounding, load and line regulation, and secondary protection circuitry (under-voltage, over-voltage, and over-current) are then introduced. Lastly, test results and characterization of the final flight design are also presented. Testing of the inrush current, the regulated output start-up, and the switching function of the power supply indicate that these performances are fully compliant with the requirements.

  11. Full Space Vectors Modulation for Nine-Switch Converters Including CF & DF Modes

    DEFF Research Database (Denmark)

    Dehghan Dehnavi, Seyed Mohammad; Mohamadian, Mustafa; Andersen, Michael A. E.

    2010-01-01

    Recently, nine-switch inverter was presented as dual output inverter. Two constant frequency (CF) and different frequency (DF) modes are defined for nine-switch inverter. However CF mode is more interesting because reasonable rating. Several switching methods have been presented for nine switch...... converter. As a space vector modulation for DF mode has already been proposed by authors. This paper proposes a full space vector modulation (SVM) for both CF and DF modes. Also practical methods are presented for SVM proposed. In addition a special SVM is proposed that offers minimum total harmonic...... distortion (THD) in DF mode. The performance of the proposed SVM is verified by simulation results....

  12. Device Loading and Efficiency of Modular Multilevel Converter under Various Modulation Strategies

    DEFF Research Database (Denmark)

    Liu, Hui; Ma, Ke; Blaabjerg, Frede

    2016-01-01

    Modular Multilevel Converter (MMC) has been becoming a very important solution for high power and medium power applications, where the efficiency and reliability performance are crucial design considerations. In this paper, three widely used modulation methods for MMC, Phase Shift PWM (PSPWM...... of the power devices in terms of power loss and thermal profiles, which are critical issues in terms of efficiency and reliability of the MMC. Special attention is given to the performance comparison of MMC under various modulation indexes as well as different switching frequencies when applying those...

  13. An Algebraic Method of Synchronous Pulsewidth Modulation for Converters for Adjustable Speed Drives

    DEFF Research Database (Denmark)

    Oleschuk, Valentin; Blaabjerg, Frede

    2002-01-01

    This paper describes the basic peculiarities of a new method of feedforward synchronous pulsewidth modulation (PWM) of the output voltage of converters, based on one-stage closed-form strategy of PWM with pure algebraic control dependencies. It is applied to voltage source inverters...... with a continuous scheme of conventional voltage space vector modulation and with two basic variants of symmetrical discontinuous PWM. Simulations give the behaviour of the proposed method and show the advantage of algebraic synchronous PWM compared with the typical asynchronous, for low indices of the frequency...

  14. An Algebraic Method of Synchronous Pulsewidth Modulation for Converters for Adjustable Speed Drives

    DEFF Research Database (Denmark)

    Oleschuk, Valentin; Blaabjerg, Frede

    2002-01-01

    This paper describes the basic peculiarities of a new method of feedforward synchronous pulsewidth modulation (PWM) of the output voltage of converters, based on one-stage closed-form strategy of PWM with pure algebraic control dependencies. It is applied to voltage source inverters...... with a continuous scheme of conventional voltage space vector modulation and with two basic variants of symmetrical discontinuous PWM. Simulations give the behaviour of the proposed method and show the advantage of algebraic synchronous PWM compared with the typical asynchronous, for low indices of the frequency...

  15. Non-Inverted Buck-Boost Converters with Dual Delta Sigma Modulators

    Science.gov (United States)

    Kobori, Yasunori; Kono, Masashi; Shimizu, Toshihiko; Kobayashi, Haruo

    This paper presents a new control circuit to create high-performance non-inverted Buck-Boost converter with dual ⊿∑ modulations. Experimental load regulation, corresponding to load current steps of ±0.5A, is within 45mVpp, and the efficiency without synchronized rectifier is 83% at input voltage 2.5V and load current 0.8A.

  16. Parametric algorithms for frequency estimation in PWM converter systems

    Energy Technology Data Exchange (ETDEWEB)

    Lobos, T.; Hejke, I.; Rezmer, J.; Sikorski, T.; Kostyla, P. [Dept. of Electrical Engineering, Wroclaw University of Technology, Wyb. Wyspianskiego 27, 50-370 Wroclaw (Poland)

    2009-11-15

    Proper estimation of voltage parameters has a significant meaning for power converters control systems. One of the measured parameter, directly associated with control process, is frequency of the basic voltage component at the converter output. Unfortunately, power converters generate a wide spectrum of harmonics as well as interharmonics, that makes difficulties in estimation this frequency. Measurement carried out in industrial applications exhibits complex nature of investigated signals often corrupted by resonances or overvoltages phenomena. It entails searching a new digital algorithms for frequency measurement. This work presents algorithm using modification of high-resolution Prony method connected with digital filtering. The investigations was based on simulations and real measured signals recorded in two different commercial PWM converters. Obtained results indicate accuracy of the method as well as its fast response. (author)

  17. Single Phase Bidirectional PWM Converter for Microgrid System

    Directory of Open Access Journals (Sweden)

    C.Kalavalli

    2013-06-01

    Full Text Available Smart grid is a newly flourishing research area because of its viable applications and expected to address the drawback of existing grid. Microgrids are the part of the Smart grid and they are designed to supply electricity for a small community such as residential areas, universities or industrial sites. Power electronics plays a vital role for connecting the renewable energy sources to Microgrid system. This paper deals the Microgrid connected single phase Bidirectional PWM converter which operates in Rectification and Inverting mode. This converter helps to connect renewable energy sources to loads as well as excess power are given to power grid. Double Loop PID control technique is used for controlling the converter for both modes. The designed Converter is simulated in MATLAB/Simulink software and results are verified using the Hardware.

  18. Design of Piston Air Compressor Unit Control System based Converter

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    <正>Based on the running characteristics and high energy consumption of air compressors in coal mines,an air pressure PID closed loop control system has been designed in this paper.The system is composed of PLC, converter and sensors etc and adopts the control method of converter triple-evaporator which makes air supply"need-based".The designed system has been applied in multiple coal mines and the results show its energy saving is remarkable and potential application is widely.

  19. Adaptive sliding mode control of interleaved parallel boost converter for fuel cell energy generation system

    DEFF Research Database (Denmark)

    El Fadil, H.; Giri, F.; Guerrero, Josep M.

    2013-01-01

    This paper deals with the problem of controlling energy generation systems including fuel cells (FCs) and interleaved boost power converters. The proposed nonlinear adaptive controller is designed using sliding mode control (SMC) technique based on the system nonlinear model. The latter accounts...... for the boost converter large-signal dynamics as well as for the fuel-cell nonlinear characteristics. The adaptive nonlinear controller involves online estimation of the DC bus impedance ‘seen’ by the converter. The control objective is threefold: (i) asymptotic stability of the closed loop system, (ii) output...... voltage regulation under bus impedance uncertainties and (iii) equal current sharing between modules. It is formally shown, using theoretical analysis and simulations, that the developed adaptive controller actually meets its control objectives....

  20. Multirate Formulation for Mismatch Sensitivity Analysis of Analog-to-Digital Converters That Utilize Parallel ΣΔ-Modulators

    Directory of Open Access Journals (Sweden)

    Per Löwenborg

    2008-02-01

    Full Text Available A general formulation based on multirate filterbank theory for analog-to-digital converters using parallel sigmadelta modulators in conjunction with modulation sequences is presented. The time-interleaved modulators (TIMs, Hadamard modulators (HMs, and frequency-band decomposition modulators (FBDMs can be viewed as special cases of the proposed description. The usefulness of the formulation stems from its ability to analyze a system's sensitivity to aliasing due to channel mismatch and modulation sequence level errors. Both Nyquist-rate and oversampled systems are considered, and it is shown how the matching requirements between channels can be reduced for oversampled systems. The new formulation is useful also for the derivation of new modulation schemes, and an example is given of how it can be used in this context.

  1. Design, control and application of modular multilevel converters for HVDC transmission systems

    CERN Document Server

    Sharifabadi, Kamran; Nee, Hans-Peter; Norrga, Staffan; Teodorescu, Remus

    2016-01-01

    Design, Control and Application of Modular Multilevel Converters for HVDC Transmission Systems is a comprehensive guide to semiconductor technologies applicable for MMC design, component sizing control, modulation, and application of the MMC technology for HVDC transmission. Separated into three distinct parts, the first offers an overview of MMC technology, including information on converter component sizing, Control and Communication, Protection and Fault Management, and Generic Modelling and Simulation. The second covers the applications of MMC in offshore WPP, including planning, technical and economic requirements and optimization options, fault management, dynamic and transient stability. Finally, the third chapter explores the applications of MMC in HVDC transmission and Multi Terminal configurations, including Supergrids.

  2. An Advanced Turbo-Brayton Converter for Radioisotope Power Systems

    Science.gov (United States)

    Zagarola, Mark V.; Izenson, Michael G.; Breedlove, Jeffrey J.; O'Connor, George M.; Ketchum, Andrew C.; Jetley, Richard L.; Simons, James K.

    2005-02-01

    Past work has shown that Brayton power converters are an attractive option for high power, long-duration space missions. More recently, Creare has shown that Brayton technology could be scaled with high efficiency and specific power to lower power levels suitable for radioisotope power conversion systems. Creare is currently leading the development of an advanced turbo-Brayton converter under NASA's Prometheus Program. The converter design is based on space-proven cryocooler technologies that have been shown to be safe; to provide long, maintenance-free lifetimes; and to have high reliability, negligible vibration emittance, and low EMI/EMC. The predicted performance of a converter at the beginning of life is greater than 20% (including electronic inefficiencies and overhead) with a converter specific power of greater than 8 We/kg for a test unit and greater than 15 We/kg for a flight unit. The degradation in performance over a 14-year mission lifetime is predicted to be negligible, and the primary life limiting factor is not expected to be an issue for greater than twice the mission duration. Work during the last year focused on the material and fabrication issues associated with a high temperature turbine and a lightweight recuperator, and the performance issues associated with the high-temperature insulation and power conversion electronics. The development of the converter is on schedule. Thermal vacuum testing to demonstrate a technology readiness level of 5 is currently planned for 2006.

  3. Optimization Control of Bidirectional Cascaded DC-AC Converter Systems

    DEFF Research Database (Denmark)

    Tian, Yanjun

    in different power flow directions, a bidirectional impedance control method is also proposed to unify and improve the system stability. Control system type number is also analyzed in this thesis, then a symmetric proportional control method for the two stage cascaded converter is proposed to reduce the dc...

  4. Grid converters for photovoltaic and wind power systems

    CERN Document Server

    Teodorescu, Remus; Rodríguez, Pedro

    2011-01-01

    "Grid Converters for Photovoltaic and Wind Power Systems provides a comprehensive description of the control of grid converters for photovoltaic and wind power systems. The authors present a range of control methods for meeting the latest application, power quality and power conversion requirements and standards, as well as looking towards potential future control functions. Practical examples, exercises, and an accompanying website with simulation models using Matlab and Simulink environments, and PSIM software make this text a pragmatic resource for electrical engineers as well as students taking related courses"--

  5. Thermoelectric Generator Power Converter System Configurations: A Review

    DEFF Research Database (Denmark)

    Man, Elena Anamaria; Schaltz, Erik; Rosendahl, Lasse

    2013-01-01

    In a Thermoelectric Generator (TEG) system, the Thermoelectric (TE) modules can be connected in series, parallel or a combination of both. Independent of the module connection, the power production of the TEG changes with the temperature gradient applied at its input. In consequence, the system...... requires a power conditioning circuit to deliver a stable and maximized output to the load. The solution is to integrate a DC-DC converter between the TEG and the load. Furthermore, a suitable control strategy is necessary to make the TEG operate at its maximum power point (MPP). The maximum power point...

  6. Laser diode monolithically integrated with an electroabsorption modulator and dual-waveguide spot-size converter

    Science.gov (United States)

    Hou, Lianping; Wang, Wei; Feng, Wen; Liang, Song; Zhu, Hongliang; Zhou, Fan; Wang, Lufeng; Bian, Jing

    2005-06-01

    A 1.60-µm laser diode and electroabsorption modulator monolithically integrated with a dual-waveguide spot-size converter output for low-loss coupling to cleaved single-mode optical fiber is demonstrated. The devices emit in a single transverse and quasi-single longitudinal mode with a side mode suppression ratio of 25.6 dB. These devices exhibit a 3-dB modulation bandwidth of 16.0 GHz, and modulator extinction ratios of 16.2 dB dc. The beam divergence angle is about 7.3×10.6 deg, resulting in 3.0-dB coupling loss with cleaved single-mode optical fiber.

  7. Wind Turbine Converter Control Interaction with Complex Wind Farm Systems

    DEFF Research Database (Denmark)

    Kocewiak, Lukasz Hubert; Hjerrild, Jesper; Bak, Claus Leth

    2013-01-01

    in this study. It is shown that wind farm components, such as long high-voltage alternating current cables and park transformers, can introduce significant low-frequency series resonances seen from the wind turbine terminals that can affect wind turbine control system operation and overall wind farm stability......This study presents wind turbine converter stability analysis of wind farms in frequency domain. The interaction between the wind turbine control system and the wind farm structure in wind farms is deeply investigated. Two wind farms (i.e. Horns Rev II and Karnice) are taken into consideration....... The same wind turbine converter control strategy is evaluated in two different wind farms. It is emphasised that the grid-side converter controller should be characterised by sufficient harmonic/noise rejection and adjusted depending on wind farms to which it is connected. Various stability indices...

  8. Wind Turbine Converter Control Interaction with Complex Wind Farm Systems

    DEFF Research Database (Denmark)

    Kocewiak, Lukasz Hubert; Hjerrild, Jesper; Bak, Claus Leth

    2013-01-01

    . The same wind turbine converter control strategy is evaluated in two different wind farms. It is emphasised that the grid-side converter controller should be characterised by sufficient harmonic/noise rejection and adjusted depending on wind farms to which it is connected. Various stability indices......This study presents wind turbine converter stability analysis of wind farms in frequency domain. The interaction between the wind turbine control system and the wind farm structure in wind farms is deeply investigated. Two wind farms (i.e. Horns Rev II and Karnice) are taken into consideration...... in this study. It is shown that wind farm components, such as long high-voltage alternating current cables and park transformers, can introduce significant low-frequency series resonances seen from the wind turbine terminals that can affect wind turbine control system operation and overall wind farm stability...

  9. Smooth-Transition Simple Digital PWM Modulator for Four-Switch Buck-Boost Converters

    Science.gov (United States)

    Rodriguez, Alberto; Rodriguez, Miguel; Vazquez, Aitor; Maija, Pablo F.; Sebastian, Javier

    2014-08-01

    Four Switch non-inverting Buck-Boost (4SBB) converters are extensively used in non-isolated applications where voltage step-up and step-down are required. In order to achieve high efficiency operation it is preferred to control the 4SBB as a Buck or Boost converter, depending on the input/output voltage ratio. However, when input and output voltages are close this approach requires near- unity conversion ratios, which are difficult to achieve in practice. Several alternative operating modes have been proposed in the literature to overcome this issue. In particular, operating the 4SBB as a Buck and Boost at the same time (Buck+Boost mode) has proven to be adequate to achieve near-unity conversion ratios.This paper proposes a simple, hardware-efficient digital pulse width modulator for a 4SBB that enables operation in Buck, Boost and Buck+Boost modes, thus allowing near-unity conversion ratios, while achieving smooth transitions between the different modes. The proposed modulator is simulated with Simulink and experimentally demonstrated using a 500W 4SBB converter with 24V input voltage and 12V-36V output voltage range.

  10. The electrical, thermal and spatial integration of a converter in a power electronic module

    NARCIS (Netherlands)

    Gerber, M.B.

    2005-01-01

    This thesis is concerned with the design and implementation of a power electronic system (14/42V DC/DC converter) that is implemented in the automotive environment, specifically the engine compartment. The power electronic system must have a high power density while operating in a high temperature e

  11. Parameter optimization of solar modules based on lens concentrators of radiation and cascade photovoltaic converters

    Science.gov (United States)

    Andreev, V. M.; Davidyuk, N. Yu.; Ionova, E. A.; Pokrovskii, P. V.; Rumyantsev, V. D.; Sadchikov, N. A.

    2010-02-01

    Two main issues governing the design of a solar concentrator module with triple-junction nano-heterostructure photovoltaic converters (PVCs) are considered: the effective concentration of radiation using Fresnel lenses and effective heat removal from PVCs. By theoretically and experimentally simulating these processes, the design parameters of module’ s elements are determined. A test batch of full-size modules has been fabricated. Each module consists of a front panel of small-size Fresnel lenses (a total of 144 lenses arranged as a 12 × 12 array) and the corresponding number of multilayer InGaP/GaAs/Ge PVCs. The PVCs are mounted on heat-distributing plates and are also integrated into a panel. The efficiency of the concentrator module with a 0.5 × 0.5-m entrance aperture measured under outdoor conditions is 24.3%, which is more than twice as high as the efficiency of standard (concentrator-free) silicon modules. In smaller test modules, the efficiency corrected for the PVC standard temperature (25° C) reaches 26.5%.

  12. Bifurcation and Chaos in a Pulse Width modulation controlled Buck Converter

    DEFF Research Database (Denmark)

    Kocewiak, Lukasz; Bak, Claus Leth; Munk-Nielsen, Stig

    2007-01-01

    by a system of piecewise-smooth nonautonomous differential equations. The research are focused on chaotic oscillations analysis and analytical search for bifurcations dependent on parameter. The most frequent route to chaos by the period doubling is observed in the second order DC-DC buck converter. Other...... bifurcations as a complex behaviour in power electronic system evidence are also described. In order to verify theoretical study the experimental DC-DC buck converter was build. The results obtained from three sources were presented and compared. A very good agreement between theory and experiment was observed....

  13. Discontinuous conduction mode analysis of phase-modulated series resonant converter

    Indian Academy of Sciences (India)

    UTSAB KUNDU; PARTHASARATHI SENSARMA

    2017-08-01

    This paper proposes an analytical approach to derive voltage gain for phase-modulated dc–dc series resonant converter (SRC) operating in discontinuous conduction mode (DCM). The conventional fundamental harmonic approximation technique is extended for a non-ideal series resonant tank to clarify the limitations of SRC operating in continuous conduction mode (CCM). The DCM analysis is described in a normalized form defining appropriate base quantities. The converter is analysed both in time and frequency domain to derive a non-linear algebraic function of diode rectifier extinction angle. The root of this function is numericallydetermined using MATLAB and used to predict the dc bus voltage. Analytical derivation of critical load resistance is discussed, which indicates the CCM–DCM boundary condition. Experimental results are presented to validate the analysis

  14. Evaluation of functional reliability indices for DC-link capacitors in pulse-width modulation converters

    Directory of Open Access Journals (Sweden)

    Gorpinich Alexander

    2017-01-01

    Full Text Available The impact of kHz range harmonics on the power losses, thermal stress, and lifetime reduction of the dc-link capacitors in pulse-width modulation (PWM converters was investigated. Expressions to evaluate the mean time to failure, survival probability, and unavailability of aging failure for dc-link capacitors are presented. The dc-link capacitors failures due to accelerated insulation aging were modeled using Weibull and normal distribution. A case study with the Siemens SINAMICS S120 frequency converter for driving of rolling mill leveler shows that the failures of motor modules due to breakdown of electrolytic dc-link capacitors registered for the time frame from May 2012 to October 2012 can be caused by the increased ambient temperature and additional heating due to high-frequency components of the ripple current. As a possible solution to improve reliability of motor modules, the four AVX FFVE4I0227K film capacitors instead of nine EPCOS B43564 electrolytic capacitors in dc-link were recommended.

  15. Accurate Sliding-Mode Control System Modeling for Buck Converters

    DEFF Research Database (Denmark)

    Høyerby, Mikkel Christian Wendelboe; Andersen, Michael Andreas E.

    2007-01-01

    This paper shows that classical sliding mode theory fails to correctly predict the output impedance of the highly useful sliding mode PID compensated buck converter. The reason for this is identified as the assumption of the sliding variable being held at zero during sliding mode, effectively mod...... approach also predicts the self-oscillating switching action of the sliding-mode control system correctly. Analytical findings are verified by simulation as well as experimentally in a 10-30V/3A buck converter.......This paper shows that classical sliding mode theory fails to correctly predict the output impedance of the highly useful sliding mode PID compensated buck converter. The reason for this is identified as the assumption of the sliding variable being held at zero during sliding mode, effectively...

  16. Switching Arithmetic for DC to DC Converters Using Delta Sigma Modulator Based Control Circuit

    Directory of Open Access Journals (Sweden)

    K.Diwakar

    2016-02-01

    Full Text Available In the proposed arithmetic unit for dc to dc converters using delta sigma modulator, a new technique is proposed for addition and multiplication of sampled analog signals. The output is in digital form to drive the converters. The conventional method has input signal limitation whereas in the proposed method the inputs can vary to full-scale. The addition of two discrete signals is done by sampling the two signals at a period called update period and feeding each signal to the input of signal dependant delta sigma modulator for half of the update period and combining the outputs for the update period. The extension of three discrete data addition can be carried out by using the same technique. For the multiplication of two discrete signals different method is adopted. One analog signal is fed to the input of first delta-sigma modulator (DSM1 after sampling. The sampled output of the second analog signal is negated or not negated depending on the bit state at the output of DSM1 and is fed to the input of second DSM(DSM2. The resulting bit stream at the output of DSM2 is the digital representation of the product of the sampled data of the two analog signals. In order to multiply three discrete data, the sampled output of third data is negated or not negated depending on the bit state at the output of DSM2 and is fed to the input of third DSM(DSM3. The resulting bit stream at the output of DSM3 is the digital representation of the product of the sampled data of the three analog signals. Using the proposed adder and multiplier circuits any expressions can be evaluated such that the average value of the digital output of the arithmetic unit over the update period gives the value of expressions during that period. The digital output of the arithmetic unit is used to drive the dc-dc converters.

  17. Design and Implementation of 12V/24V Closed loop Boost Converter for Solar Powered LED Lighting System

    Directory of Open Access Journals (Sweden)

    P.Sathya

    2013-02-01

    Full Text Available this paper presents the design and implementation of high performance closed loop Boost converter for solar powered HBLED lighting system. The proposed system consists of solar photovoltaic module, a closed loop boost converter and LED lighting module. The closed loop boost converter is used to convert a low level dc input voltage from solar PV module to a high level dc voltage required for the load. To regulate the output of the converter, closed loop voltage feedback technique is used. The feedback voltage is compared with a reference voltage and a control signal is generated and amplified. The amplified signal is fed to 555 Timer which in turn generates a PWM signal which controls the switching of MOSFET. Thus by switching of MOSFET it would try to keep output as constant. Initially the boost converter, timer circuit, amplifier circuit and LED light circuits are designed, simulated and finally implemented in printed circuit board. The simulation studies are carried out in MULTISIM. Theexperimental results for solar PV and boost converter obtained in both software and hardware are presented here.

  18. High reliability DC/DC converter module for electronic boards equipped with FPGAs

    Science.gov (United States)

    Viganò, W.; Boccardi, A.; Zamantzas, C.

    2015-01-01

    The Beam Instrumentation Group at CERN is designing a new general-purpose VME carrier module utilising several PTH04T230W DC/DC converters. These off-the-shelf converters are built with unshielded inductors and need to be mounted on the printed circuit board as stand-alone components. Thus, reducing the global manageability and increasing the total cost of the carrier module. The new design aims to develop a module with better power dissipation, efficiency and reliability. In the future, it should be also possible to be directly integrated on the mainboard. For this reason, a Buck DC/DC converter has been implemented with the following main characteristics: input range from 3.0 V to 5.5 V; output range from 0.6 V to 3.3 V, settable by means of an external resistor; output current protection at 6 A; maximum output ripple ± 50 mVpp; switching frequency of 300KHz; short circuit protection; On/Off function; EMI reduction with frequency spread spectrum; soft-start function and thermal shutdown, in a 16 × 19 mm compact size. The selected buck controller is the TPS40303 integrated circuit and drives the CSD16321 power MOSFET, both from Texas Instruments. All selected components have been used at a minimum derating of 50% to reduce component stress and increase the reliability of this module. The selected inductors, i.e. Bourns SRP1055, are the main contributor for the high efficiency (95%), due to their very low equivalent series resistance. On the 4-layer PCB comprising all the components of this module, a snubber circuit, for further reduction of the output ripple due to the MOSFET ringing, can be mounted optionally. It is left as an option due to its effect on the total efficiency. The board layout has been optimized for maximum heat transfer and it can be used without active cooling. The board can maintain the maximum temperature on its surface, while at maximum current output, below 55°C at 25°C ambient temperature. An example of the electrical performance

  19. Photovoltaic module mounting system

    Science.gov (United States)

    Miros, Robert H. J.; Mittan, Margaret Birmingham; Seery, Martin N.; Holland, Rodney H.

    2012-04-17

    A solar array mounting system having unique installation, load distribution, and grounding features, and which is adaptable for mounting solar panels having no external frame. The solar array mounting system includes flexible, pedestal-style feet and structural links connected in a grid formation on the mounting surface. The photovoltaic modules are secured in place via the use of attachment clamps that grip the edge of the typically glass substrate. The panel mounting clamps are then held in place by tilt brackets and/or mid-link brackets that provide fixation for the clamps and align the solar panels at a tilt to the horizontal mounting surface. The tilt brackets are held in place atop the flexible feet and connected link members thus creating a complete mounting structure.

  20. Force Modulator System

    Energy Technology Data Exchange (ETDEWEB)

    Redmond Clark

    2009-04-30

    Many metal parts manufacturers use large metal presses to shape sheet metal into finished products like car body parts, jet wing and fuselage surfaces, etc. These metal presses take sheet metal and - with enormous force - reshape the metal into a fully formed part in a manner of seconds. Although highly efficient, the forces involved in forming metal parts also damage the press itself, limit the metals used in part production, slow press operations and, when not properly controlled, cause the manufacture of large volumes of defective metal parts. To date, the metal-forming industry has not been able to develop a metal-holding technology that allows full control of press forces during the part forming process. This is of particular importance in the automotive lightweighting efforts under way in the US automotive manufacturing marketplace. Metalforming Controls Technology Inc. (MC2) has developed a patented press control system called the Force Modulator that has the ability to control these press forces, allowing a breakthrough in stamping process control. The technology includes a series of hydraulic cylinders that provide controlled tonnage at all points in the forming process. At the same time, the unique cylinder design allows for the generation of very high levels of clamping forces (very high tonnages) in very small spaces; a requirement for forming medium and large panels out of HSS and AHSS. Successful production application of these systems testing at multiple stamping operations - including Ford and Chrysler - has validated the capabilities and economic benefits of the system. Although this technology has been adopted in a number of stamping operations, one of the primary barriers to faster adoption and application of this technology in HSS projects is system cost. The cost issue has surfaced because the systems currently in use are built for each individual die as a custom application, thus driving higher tooling costs. This project proposed to better

  1. Harmonics in power systems of ships with electrical propulsion drives. Comparison between different converters

    Energy Technology Data Exchange (ETDEWEB)

    Lehtonen, M. [VTT Energy, Espoo (Finland). Energy Systems

    1996-11-01

    In this report the effects of harmonics in marine power systems is discussed and a comparison is given between the most typical converter types, including pulse width modulated drives, load commutated inverters and cycloconverters. The effect of harmonic distortion on the power system equipment and loads is first briefly discussed. Special attention is given to the circumstances in the low voltage distribution system, where general load equipment is connected. In addition to the total harmonic distortion the effect of voltage deviation to the supply quality is also considered. The origin of harmonics in the load currents of the three converter types is then considered. The differences between the converters are outlined, and the most typical spectra are presented. The possible means for reducing the harmonic distortion are also studied. The solutions considered are the increasing of the short circuit level, the use of harmonic filters and the increasing of the pulse number. In the case of cycloconverters, the optimization of the phase shift between the parallel operating bridges is also presented. Finally the effects of different converter types on the voltage quality are compared using calculations made for a typical marine power system. (author)

  2. Assessment of an Average Controller for a DC/DC Converter via Either a PWM or a Sigma-Delta-Modulator

    Directory of Open Access Journals (Sweden)

    R. Silva-Ortigoza

    2014-01-01

    Full Text Available Sliding mode control is a discontinuous control technique that is, by its nature, appropriate for controlling variable structure systems, such as the switch regulated systems employed in power electronics. However, when designing control laws based on the average models of these systems a modulator is necessary for their experimental implementation. Among the most widely used modulators in power electronics are the pulse width modulation (PWM and, more recently, the sigma-delta-modulator (Σ-Δ-modulator. Based on the importance of achieving an appropriate implementation of average control laws and the relevance of the trajectory tracking task in DC/DC power converters, for the first time, this research presents the assessment of the experimental results obtained when one of these controllers is implemented through either a PWM or a Σ-Δ-modulator to perform such a task. A comparative assessment based on the integral square error (ISE index shows that, at frequencies with similar efficiency, the Σ-Δ-modulator provides a better tracking performance for the DC/DC Buck converter. In this paper, an average control based on differential flatness was used to perform the experiments. It is worth mentioning that a different trajectory tracking controller could have been selected for this research.

  3. Research on Energy Conversion System of Floating Wave Energy Converter

    Institute of Scientific and Technical Information of China (English)

    张亚群; 盛松伟; 游亚戈; 吴必军; 刘洋

    2014-01-01

    A wave power device includes an energy harvesting system and a power take-off system. The power take-off system of a floating wave energy device is the key that converts wave energy into other forms. A set of hydraulic power take-off system, which suits for the floating wave energy devices, includes hydraulic system and power generation system. The hydraulic control system uses a special“self-hydraulic control system”to control hydraulic system to release or save energy under the maximum and the minimum pressures. The maximum pressure is enhanced to 23 MPa, the minimum to 9 MPa. Quite a few experiments show that the recent hydraulic system is evidently improved in efficiency and reliability than our previous one, that is expected to be great significant in the research and development of our prototype about wave energy conversion.

  4. DC-DC converters in distributed photovoltaic electricity system. Analysis, control and design

    Energy Technology Data Exchange (ETDEWEB)

    Huusari, J.

    2012-10-15

    This thesis presents a comprehensive review on switched-mode converters in terms of dynamic behavior and practical limitations that arise from the fundamental properties of the electrical sources and loads, control engineering principles and topological properties of the converters. The main focus is on analyzing the behavior of a single converter used to interface a photovoltaic generator into a high-voltage dc link. The main objective is to introduce interfacing principles with numerous examples and a thorough discussion. The interfacing of photovoltaic generators by means of switched-mode converters has proven to be problematic according to numerous scientific publications indicating operational disadvantages and anomalies. The output characteristics of the photovoltaic generator, which are bound to varying environmental conditions, introduce design challenges. It has been recognized recently that the photovoltaic generator does not contain similar electrical behavior as conventional electrical sources, most notably due to its limited-power characteristics, yielding two distinctive operating regions. Yet, the constraints arising from the properties of the source have not been completely recognized, although the effect of these constraints can be seen from the published research results. When switched-mode converters are used to adapt individual photovoltaic modules into larger system by connecting converters in series or in parallel, severe operational limitations are observed. On the other hand, if the photovoltaic generator is substituted with a source that does not contain similar characteristics, observations may lead to misconclusions as the effect of the photovoltaic generator is not properly modeled. Therefore, claims that are not valid for actual applications with photovoltaic generators may be presented and widely accepted. This thesis presents methods to perform proper analysis of switched-mode converters implemented in distributed photovoltaic

  5. Individual Module Maximum Power Point Tracking for Thermoelectric Generator Systems

    Science.gov (United States)

    Vadstrup, Casper; Schaltz, Erik; Chen, Min

    2013-07-01

    In a thermoelectric generator (TEG) system the DC/DC converter is under the control of a maximum power point tracker which ensures that the TEG system outputs the maximum possible power to the load. However, if the conditions, e.g., temperature, health, etc., of the TEG modules are different, each TEG module will not produce its maximum power. If each TEG module is controlled individually, each TEG module can be operated at its maximum power point and the TEG system output power will therefore be higher. In this work a power converter based on noninverting buck-boost converters capable of handling four TEG modules is presented. It is shown that, when each module in the TEG system is operated under individual maximum power point tracking, the system output power for this specific application can be increased by up to 8.4% relative to the situation when the modules are connected in series and 16.7% relative to the situation when the modules are connected in parallel.

  6. Living Systems Energy Module

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-26

    The Living Systems Energy Module, renamed Voyage from the Sun, is a twenty-lesson curriculum designed to introduce students to the major ways in which energy is important in living systems. Voyage from the Sun tells the story of energy, describing its solar origins, how it is incorporated into living terrestrial systems through photosynthesis, how it flows from plants to herbivorous animals, and from herbivores to carnivores. A significant part of the unit is devoted to examining how humans use energy, and how human impact on natural habitats affects ecosystems. As students proceed through the unit, they read chapters of Voyage from the Sun, a comic book that describes the flow of energy in story form (Appendix A). During the course of the unit, an ``Energy Pyramid`` is erected in the classroom. This three-dimensional structure serves as a classroom exhibit, reminding students daily of the importance of energy and of the fragile nature of our living planet. Interactive activities teach students about adaptations that allow plants and animals to acquire, to use and to conserve energy. A complete list of curricular materials and copies of all activity sheets appear in Appendix B.

  7. Two-mode dynamics in pulse-modulated control systems

    DEFF Research Database (Denmark)

    Zhusubaliyev, Z.T.; Yanochkina, O.O.; Mosekilde, Erik

    2010-01-01

    as an example the paper provides a survey of three new mechanisms of torus bifurcation that can be observed in pulse-modulated control systems. The paper concludes with a discussion of the influence that operation in the torus regimes will have on the efficiency of the converter......Pulse-modulated converter systems play an important role in modern power electronics. Systems of this type also deserve considerable theoretical interest because of the complex interplay they exhibit between ordinary (smooth) bifurcations and so-called border-collision bifurcations generated...... by the switching dynamics. Particularly interesting are the unusual transitions to torus dynamics, i.e., to a mode of behavior in which the regular switching dynamics is modulated by another oscillatory mode that may arise through instability in the feedback control. Using the model of a two-level DC/DC converter...

  8. New method to implement digital down converter in radar system

    Institute of Scientific and Technical Information of China (English)

    Ma Zhigang; Wen Biyang; Zhou Hao; Bai Liyun

    2005-01-01

    Digital down converter (DDC) is the main part of the next generation high frequency (HF) radar. In order to realize the single chip integrations of digital receiver hardware in the next generation HF Radar, a new design for DDC by using FPGA is presented. Some important and practical applications are given in this paper, and the result can prove the validity. Because we can adjust the parameters freely according to our need, the DDC system can be adapted to the next generation HF radar system.

  9. Lightweight, Efficient Power Converters for Advanced Turboelectric Aircraft Propulsion Systems

    Science.gov (United States)

    Hennessy, Michael J.

    2014-01-01

    NASA is investigating advanced turboelectric aircraft propulsion systems that use superconducting motors to drive multiple distributed turbofans. Conventional electric motors are too large and heavy to be practical for this application; therefore, superconducting motors are required. In order to improve aircraft maneuverability, variable-speed power converters are required to throttle power to the turbofans. The low operating temperature and the need for lightweight components that place a minimum of additional heat load on the refrigeration system open the possibility of incorporating extremely efficient cryogenic power conversion technology. This Phase II project is developing critical components required to meet these goals.

  10. Development of a Modular Power Converter

    Science.gov (United States)

    Stepanov, A.; Biesenieks, L.; Sokolovs, A.; Galkin, I.

    2009-01-01

    This report describes the most important details of elaboration of a versatile power module that can be utilized as a part of various converters. Two or more modules connected together can form a frequency converter or multilevel converter or 3-phase inverter/rectifier etc. Initially the module was developed for fast prototyping of uninterruptible power supplies and energy systems with alternative energy sources. The module can be used also as a basis for laboratory equipment of the power electronics course.

  11. Modeling and Control of Grid Side Converter in Wind Power Generation System Based on Synchronous VFDPC with PLL

    DEFF Research Database (Denmark)

    Guo, Yougui; Zeng, Ping; Li, Lijuan

    2011-01-01

    Virtual flux oriented direct power control (VFDPC) is combined space vector modulation (SVM) with PI of DC-link voltage, active power and reactive power to control the grid side converter in wind power generation system in this paper. VFDPC has reached good performances with PLL (phase lock loop...

  12. Windowed SHE-PWM of Interleaved Four-Quadrant Converters for Resonance Suppression in Traction Power Supply Systems

    DEFF Research Database (Denmark)

    Song, Kejian; Konstantinou, Georgios; Mingli, Wu

    2017-01-01

    AC electric locomotives that use a number of interleaved four-quadrant converters generate high-frequency switching harmonics which may stimulate certain resonances in traction power supply systems (TPSSs). A windowed selective harmonic elimination pulse-width modulation (SHE-PWM) method...

  13. Modeling and Control of Grid Side Converter in Wind Power Generation System Based on Synchronous VFDPC with PLL

    DEFF Research Database (Denmark)

    Guo, Yougui; Zeng, Ping; Li, Lijuan

    2011-01-01

    Virtual flux oriented direct power control (VFDPC) is combined space vector modulation (SVM) with PI of DC-link voltage, active power and reactive power to control the grid side converter in wind power generation system in this paper. VFDPC has reached good performances with PLL (phase lock loop...

  14. Implementation of Control System for Hydrokinetic Energy Converter

    Directory of Open Access Journals (Sweden)

    Katarina Yuen

    2013-01-01

    Full Text Available At Uppsala University, a research group is investigating a system for converting the power in freely flowing water using a vertical-axis turbine directly connected to a permanent magnet generator. An experimental setup comprising a turbine, a generator, and a control system has been constructed and will be deployed in the Dalälven river in the town of Söderfors in Sweden. The design, construction, simulations, and laboratory tests of the control system are presented in this paper. The control system includes a startup sequence for the turbine and load control. These functions have performed satisfactorily in laboratory tests. Simulations of the system show that the power output is not maximized at the same tip-speed ratio as that which maximizes the turbine power capture.

  15. Modulation Schemes With Enhanced Switch Thermal Distribution for Single-Phase AC–DC–AC Reduced-Switch Converters

    DEFF Research Database (Denmark)

    Qin, Zian; Loh, Poh Chiang; Blaabjerg, Frede

    2016-01-01

    various topologies have since been proposed. The intention of this paper is, thus, to study two promising single-phase ac-dc-ac converters using reduced number of switches, and subsequently proposes modulation schemes for them. The proposed schemes help the converters to achieve better thermal spread...... among their switches, while keeping their dc-link voltages low. Single points of failure are thus minimized, allowing the converters to have longer lifetimes. Simulation and experimental results have demonstrated the intended performances, hence verifying the analyses presented in this paper....

  16. Pulse pattern modulated strategy for harmonic current components reduction in three-phase AC-DC converters

    DEFF Research Database (Denmark)

    Davari, Pooya; Zare, Firuz; Blaabjerg, Frede

    2015-01-01

    Generated harmonic current as a consequence of employing power electronics converter is known as an important power quality issue in distribution networks. From industry point of view complying with international standards is mandatory, however cost and efficiency are two other important features......, which need to be considered in order to be competitive in the market. Therefore, having a flexibility to meet various requirements imposed by the standard recommendations or costumer needs is at most desirable. This makes the generated harmonic current mitigation a challenging task especially with three......-phase diode bridge rectifier, which still is preferred in many power electronic systems. This paper addresses a novel current modulation strategy using a single-switch boost three-phase diode bridge rectifier. The proposed method can selectively mitigate current harmonics, which makes it suitable...

  17. Pulse Pattern-Modulated Strategy for Harmonic Current Components Reduction in Three-Phase AC–DC Converters

    DEFF Research Database (Denmark)

    Davari, Pooya; Zare, Firuz; Blaabjerg, Frede

    2016-01-01

    Generated harmonic current as a consequence of employing power electronics converter is known as an important power quality issue in distribution networks. From industry point of view complying with international standards is mandatory, however cost and efficiency are two other important features......, which need to be considered in order to be competitive in the market. Therefore, having a flexibility to meet various requirements imposed by the standard recommendations or costumer needs is at most desirable. This makes the generated harmonic current mitigation a challenging task especially with three......-phase diode bridge rectifier, which still is preferred in many power electronic systems. This paper addresses a novel current modulation strategy using a single-switch boost three-phase diode bridge rectifier. The proposed method can selectively mitigate current harmonics, which makes it suitable...

  18. High Efficient Bidirectional Battery Converter for residential PV Systems

    DEFF Research Database (Denmark)

    Pham, Cam; Kerekes, Tamas; Teodorescu, Remus

    2012-01-01

    Photovoltaic (PV) installation is suited for the residential environment and the generation pattern follows the distribution of residential power consumption in daylight hours. In the cases of unbalance between generation and demand, the Smart PV with its battery storage can absorb or inject...... the power to balance it. High efficient bidirectional converter for the battery storage is required due high system cost and because the power is processed twice. A 1.5kW prototype is designed and built with CoolMOS and SiC diodes, >;95% efficiency has been obtained with 200 kHz hard switching....

  19. Distributed control system for parallel-connected DC boost converters

    Energy Technology Data Exchange (ETDEWEB)

    Goldsmith, Steven

    2017-08-15

    The disclosed invention is a distributed control system for operating a DC bus fed by disparate DC power sources that service a known or unknown load. The voltage sources vary in v-i characteristics and have time-varying, maximum supply capacities. Each source is connected to the bus via a boost converter, which may have different dynamic characteristics and power transfer capacities, but are controlled through PWM. The invention tracks the time-varying power sources and apportions their power contribution while maintaining the DC bus voltage within the specifications. A central digital controller solves the steady-state system for the optimal duty cycle settings that achieve a desired power supply apportionment scheme for a known or predictable DC load. A distributed networked control system is derived from the central system that utilizes communications among controllers to compute a shared estimate of the unknown time-varying load through shared bus current measurements and bus voltage measurements.

  20. Delta-Sigma AD-Converters Practical Design for Communication Systems

    CERN Document Server

    Gaggl, Richard

    2013-01-01

    The emphasis of this book is on practical design aspects for broadband A/D converters for communication systems. The embedded designs are employed for transceivers in the field of ADSL solutions and WLAN applications. An area- and power-efficient realization of a converter is mandatory to remain competitive in the market. The right choice for the converter topology and architecture needs to be done very carefully to result in a competitive FOM. The book begins with a brief overview of basic concepts about ADSL and WLAN to understand the ADC requirements. At architectural level, issues on different modulator topologies are discussed employing the provided technology node. The design issues are pointed out in detail for modern digital CMOS technologies, beginning with 180nm followed by 130nm and going down to 65nm feature size. Beside practical aspects, challenges to mixed-signal design level are addressed to optimize the converters in terms of consumed chip area, power consumption and design for high yield in ...

  1. DARHT2 X-ray converter target system comparison

    Energy Technology Data Exchange (ETDEWEB)

    Bergstrom, P M; Caporaso, G J; Chen, Y J; Ho, D D; McCarrick, J F; Pincosy, P A; Rambo, P W

    1999-03-24

    Four short current pulses with various pulse widths and spacing will be delivered to the x-ray converter target on the second-axis of the Dual-Axis Radiographic Hydrodynamic Test (DARHT-II) facility. To ensure that the DARHT-II multi-pulse target will provide enough target material for x-ray production for all four pulses, the target needs either to survive the strike of four electron pulses or to accommodate target replenishment. A distributed target may survive hitting of four electron pulses. For target replenishment, two types of target configurations are being considered: stationary target systems with beam repositioning and dynamic moving target systems. They compare these three target systems and their radiographic performance.

  2. Implementation of a PV lighting system based on DC-DC converter with intelligent controlled approach

    Energy Technology Data Exchange (ETDEWEB)

    Hua, C.-C.; Chuang, D.-J. [National Yunlin Univ. of Science and Technology, Douliou, Yunlin, Taiwan (China). Dept. of Electrical Engineering; Chuang, C.-W. [National Yunlin Univ. of Science and Technology, Douliou, Yunlin, Taiwan (China). Graduate School of Engineering Science and Technology

    2007-07-01

    Photovoltaic (PV) lighting systems for municipalities represent one of the largest cost effective markets for PVs. The installation cost of just one or two utility power poles can justify the initial cost of a PV lighting system. However, many previous PV lighting systems have experienced a number of component failures including premature charge controller, battery, and ballast illumination failures. This paper presented the design and implementation of a digital high performance photovoltaic lighting system based on a microcontroller. A high brightness light-emitting diode (HBLED), was used as it can work at very high efficiency with a specially designed lighting power module. The proposed system consisted of a photovoltaic module, a light emitting diode (LED) lighting module, a bi-directional buck-boost converter and a battery. The paper analysed battery charging methods and proposed a control strategy and hardware implementation. The dimming control methods for LED were also discussed and compared. The experimental results were also provided to verify the theoretical analysis and design procedure of a digital controlled photovoltaic lighting system. It was concluded that the experimental results verified the performance of the proposed photovoltaic lighting system. 8 refs., 1 tab., 18 figs.

  3. Engine Performance (Section C: Emission Control Systems). Auto Mechanics Curriculum Guide. Module 3. Instructor's Guide.

    Science.gov (United States)

    Rains, Larry

    This engine performance (emission control systems) module is one of a series of competency-based modules in the Missouri Auto Mechanics Curriculum Guide. Topics of this module's five units are: positive crankcase ventilation (PCV) and evaporative emission control systems; exhaust gas recirculation (EGR); air injection and catalytic converters;…

  4. Series and parallel connection of ZVS-ZCS push-pull DC/DC converter module

    National Research Council Canada - National Science Library

    Chu, Ching-Lung; Chien, Chin-Nan

    2012-01-01

    ..., the input current of the modular converter increases as the output voltage decreases. A standardized modular converter can be connected either in series or in parallel to increase its rated capacity...

  5. New Multiphase Hybrid Boost Converter with Wide Conversion Ratio for PV System

    Directory of Open Access Journals (Sweden)

    Ioana-Monica Pop-Calimanu

    2014-01-01

    Full Text Available A new multiphase hybrid boost converter, with wide conversion ratio as a solution for photovoltaic energy system, is presented in this paper. To ensure that all the phases of the converter operate at the same switching frequency we use interleaving topology. The proposed converter can be used as an interface between the PV system and the DC load/inverter. This multiphase converter has the advantage of reduced value and physical size of the input and output capacitor as well as the effort for the inductors. To validate the operation of the converter we provide the analyses and the simulation results of the converter.

  6. Design and Analysis of the Main AC/DC Converter System for ITER

    Institute of Scientific and Technical Information of China (English)

    盛志才; 许留伟; 傅鹏

    2012-01-01

    A design of the main AC/DC converter system for ITER is described and the configuration of the main AC/DC converters is presented. To reduce the reactive power absorbed from the converter units, the main AC/DC converters are designed to be series-connected and work in a sequential mode. The structure of the regulator of the converter system is described. A simulation model was built up for the PSCAD/EMTDC code, and the design was validated accordingly. Harmonic analysis and reactive power calculation of the converters units are presented. The results reveal the advantage of sequential control in reducing reactive power and harmonics.

  7. Modulation Methods for Neutral-Point-Clamped Wind Power Converter Achieving Loss and Thermal Redistribution Under Low-Voltage Ride-Through

    DEFF Research Database (Denmark)

    Ma, Ke; Blaabjerg, Frede

    2014-01-01

    The three-level neutral-point (NP)-clamped (3L-NPC) converter is a promising multilevel topology in the application of megawatt wind power generation systems. However, the growing requirements by grid codes may impose high stress and even give reliability problem to this converter topology....... This paper investigates the loss and thermal performances of a 10-MW 3L-NPC wind power inverter undergoing low-voltage ride-through (LVRT) operation. A series of new space vector modulation methods is then proposed to relocate the thermal loading among the power switching devices. It is concluded that......, with the proposed modulation methods, the thermal distribution in the 3L-NPC wind power inverter undergoing LVRT becomes more equal, and the junction temperature of the most stressed devices can be also relieved. Also, the control ability of the dc-bus NP potential, which is one of the crucial considerations...

  8. Analysis and performance of paralleling circuits for modular inverter-converter systems

    Science.gov (United States)

    Birchenough, A. G.; Gourash, F.

    1972-01-01

    As part of a modular inverter-converter development program, control techniques were developed to provide load sharing among paralleled inverters or converters. An analysis of the requirements of paralleling circuits and a discussion of the circuits developed and their performance are included in this report. The current sharing was within 5.6 percent of rated-load current for the ac modules and 7.4 percent for the dc modules for an initial output voltage unbalance of 5 volts.

  9. Electroabsorption modulated semiconductor optical amplifier monolithically integrated with spot-size converters

    Science.gov (United States)

    Hou, Lianping; Zhu, Hongliang; Zhou, Fan; Wang, Baojun; Bian, Jing; Wang, Wei

    2006-02-01

    We have demonstrated an electroabsorption modulator (EAM) and semiconductor optical amplifier (SOA) monolithically integrated with novel dual-waveguide spot-size converters (SSCs) at the input and output ports for low-loss coupling to planar light-guide circuit silica waveguide or cleaved single-mode optical fiber. The device is fabricated by means of selective-area MOVPE growth (SAG), quantum well intermixing (QWI) and asymmetric twin waveguide (ATG) technologies with only three steps low-pressure MOVPE growth. For the device structure, in SOA/EAM section, double ridge structure was employed to reduce the EAM capacitances and enable high bit-rate operation. In the SSC sections, buried ridge stripe (BRS) were incorporated. Such a combination of ridge, ATG and BRS structure is reported for the first time in which it can take advantage of both easy processing of ridge structure and the excellent mode characteristic of BRS. At the wavelength range of 1550-1600 nm, lossless operation with extinction ratios of 25 dB DC and more than 10 GHz 3-dB bandwidth is successfully achieved. The beam divergence angles of the input and output ports of the device are as small as 8.0°×12.6°, resulting in 3.0 dB coupling loss with cleaved single-mode optical fiber.

  10. Compact high voltage, high peak power, high frequency transformer for converter type modulator applications.

    Science.gov (United States)

    Reghu, T; Mandloi, V; Shrivastava, Purushottam

    2016-04-01

    The design and development of a compact high voltage, high peak power, high frequency transformer for a converter type modulator of klystron amplifiers is presented. The transformer has been designed to operate at a frequency of 20 kHz and at a flux swing of ±0.6 T. Iron (Fe) based nanocrystalline material has been selected as a core for the construction of the transformer. The transformer employs a specially designed solid Teflon bobbin having 120 kV insulation for winding the high voltage secondary windings. The flux swing of the core has been experimentally found by plotting the hysteresis loop at actual operating conditions. Based on the design, a prototype transformer has been built which is per se a unique combination of high voltage, high frequency, and peak power specifications. The transformer was able to provide 58 kV (pk-pk) at the secondary with a peak power handling capability of 700 kVA. The transformation ratio was 1:17. The performance of the transformer is also presented and discussed.

  11. Comparison of Foundation Systems for Wave Energy Converters Wavestar

    DEFF Research Database (Denmark)

    Vaitkunaite, Evelina; Ibsen, Lars Bo; Nielsen, Benjaminn Nordahl;

    2013-01-01

    In order to deliver cost competitive solutions, Wave Energy Converters (WEC) must be optimized in several fields, e.g. transportation, installation, structure, machinery etc. Large expenses lie on the superstructure support, i.e. the offshore foundation. Geotechnical analysis and optimization....... In such a solution horizontal wind and wave loads are dominant. Gravity based, pile and bucket foundations are universally applied solutions for the offshore structures. The suitability of these types for a WEC is analysed and commented. The foundations are designed to satisfy ultimate and serviceability limit state...... of six possible foundation solutions for WEC are presented in this article. The study is performed for WEC superstructure supported by two or four foundations. In the four-column system horizontal wind and wave loads are transformed as a pair of vertical forces, acting in tension and compression. When...

  12. Monolithically integrated laser diode and electroabsorption modulator with dual-waveguide spot-size converter input and output

    Science.gov (United States)

    Hou, Lianping; Wang, Wei; Zhu, Hongliang; Zhou, Fan; Wang, Lufeng; Bian, Jing

    2005-08-01

    We have demonstrated a 1.60 µm ridge-structure laser diode and electroabsorption modulator monolithically integrated with buried-ridge-structure dual-waveguide spot-size converters at the input and output ports for low-loss coupling to a cleaved single-mode optical fibre by means of selective area growth and asymmetric twin waveguide technologies. The devices emit in single transverse and quasi-single longitudinal modes with a side mode suppression ratio of 25.6 dB. These devices exhibit 3 dB modulation bandwidth of 15.0 GHz and modulator extinction ratios of 14.0 dB dc. The output beam divergence angles of the spot-size converter in the horizontal and vertical directions are as small as 7.3° × 10.6°, respectively, resulting in 3.0 dB coupling loss with a cleaved single-mode optical fibre.

  13. Application of chaotic pulse width modulation control for suppressing electromagnetic interference in a half-bridge converter

    Directory of Open Access Journals (Sweden)

    Yuhong Song

    2014-08-01

    Full Text Available It was proposed in the former research that chaos control can be used to suppress electromagnetic interference (EMI in DC–DC converters. Analysis on a half-bridge converter is detailed in this study. Here, the practical example of the power supply of personal computers is given to show that, with an external chaotic signal to a pulse width modulation control circuit, the proposed approach can reduce EMI by reducing the amplitudes of power signals such as transformer current and output inductor currents at multiples of fundamental frequency.

  14. Very Thin Flexible Coupled Inductors for PV Module Integrated GaN Converter

    DEFF Research Database (Denmark)

    Acanski, Milos; Ouyang, Ziwei; Popovic-Gerber, Jelena

    2012-01-01

    proposed with more granular power processing by means of distributed maximum power point tracking (DMPPT). This is achieved by adjoining a MPPT unit to each PV module in the PV array. This paper presents a step further in the distributed power tracking approach, with a concept of very low profile power......As the PV energy penetrates into the urban area, shortcomings of the conventional centralized PV system architectures become more pronounced under the influence of urban environment with shading, soiling and orientation mismatch issues. To overcome these limitations new PV system architectures were...

  15. Very Thin Flexible Coupled Inductors for PV Module Integrated GaN Converter

    DEFF Research Database (Denmark)

    Acanski, Milos; Ouyang, Ziwei; Popovic-Gerber, Jelena;

    2012-01-01

    As the PV energy penetrates into the urban area, shortcomings of the conventional centralized PV system architectures become more pronounced under the influence of urban environment with shading, soiling and orientation mismatch issues. To overcome these limitations new PV system architectures were...... proposed with more granular power processing by means of distributed maximum power point tracking (DMPPT). This is achieved by adjoining a MPPT unit to each PV module in the PV array. This paper presents a step further in the distributed power tracking approach, with a concept of very low profile power...

  16. Single-Switch Equalization Charger Using Multiple Stacked Buck-Boost Converters for Series-Connected Energy-Storage Modules

    Science.gov (United States)

    Uno, Masatoshi; Tanaka, Koji

    Series connections of energy-storage modules such as electric double-layer capacitors (EDLCs) and lithium-ion batteries result in voltage imbalance because of the nonuniform properties of individual modules. Conventional voltage equalizers based on traditional dc-dc converters require numerous switches and/or transformers, and therefore, their costs and complexity tend to increase. This paper proposes a novel single-switch equalization charger using multiple stacked buck-boost converters. The single-switch operation not only reduces the circuit complexity but also contributes to increasing the reliability. The fundamental operating principles and design procedures of key components are presented in detail. An experimental charge test using a 25W prototype of the proposed equalization charger was performed for four series-connected EDLC modules whose initial voltages were intentionally imbalanced. Experimental results demonstrated that the proposed equalization charger could charge the series-connected modules preferentially in the order of increasing module voltage and that all the modules could be charged up to a uniform voltage level.

  17. A new multi-motor drive system based on two-stage direct power converter

    OpenAIRE

    Kumar, Dinesh

    2011-01-01

    The two-stage AC to AC direct power converter is an alternative matrix converter topology, which offers the benefits of sinusoidal input currents and output voltages, bidirectional power flow and controllable input power factor. The absence of any energy storage devices, such as electrolytic capacitors, has increased the potential lifetime of the converter. In this research work, a new multi-motor drive system based on a two-stage direct power converter has been proposed, with two motors c...

  18. Inhibitors of angiotensin-converting enzyme modulate mitosis and gene expression in pancreatic cancer cells

    Energy Technology Data Exchange (ETDEWEB)

    Reddy, M.K.; Baskaran, K.; Molteni, A. [Northwestern Univ. Medical School, Chicago, IL (United States)

    1995-12-01

    The angiotensin-converting enzyme (ACE) inhibitor captopril inhibits mitosis in several cell types that contain ACE and renin activity. In the present study, we evaluated the effect of the ACE inhibitors captopril and CGS 13945 (10{sup {minus}8} to 10{sup {minus}2}M) on proliferation and gene expression in hamster pancreatic duct carcinoma cells in culture. These cells lack renin and ACE activity. Both ACE inhibitors produced a dose-dependent reduction in tumor cell proliferation within 24 hr. Captopril at a concentration of 0.36 mM and CGS 13945 at 150 {mu}M decreased cellular growth rate to approximately half that of the control. Neither drug influenced the viability or the cell cycle distribution of the tumor cells. Slot blot analysis of mRNA for four genes, proliferation associated cell nuclear antigen (PCNA), K-ras, protein kinase C-{Beta} (PKC-{Beta}) and carbonic anhydrase II (CA II) was performed. Both ACE inhibitors increased K-ras expression by a factor of 2, and had no effect on CA II mRNA levels. Captopril also lowered PCNA by 40% and CGS 13945 lowered PKC-{Beta} gene expression to 30% of the control level. The data demonstrate that ACE inhibitors exhibit antimitotic activity and differential gene modulation in hamster pancreatic duct carcinoma cells. The absence of renin and ACE activity in these cells suggests that the antimitotic action of captopril and CGS 13945 is independent of renin-angiotensin regulation. The growth inhibition may occur through downregulation of growth-related gene expression. 27 refs., 5 figs.

  19. Power supply of autonomous systems using solar modules

    Science.gov (United States)

    Yurchenko, A. V.; Zotov, L. G.; Mekhtiev, A. D.; Yugai, V. V.; Tatkeeva, G. G.

    2015-04-01

    The article shows the methods of constructing autonomous decentralized energy systems from solar modules. It shows the operation of up DC inverter. It demonstrates the effectiveness of DC inverters with varying structure. The system has high efficiency and low level of conductive impulse noise and at the same time the system is practically feasible. Electrical processes have been analyzed to determine the characteristics of operating modes of the main circuit elements. Recommendations on using the converters have been given.

  20. Energy Conversion Module (ECM) - DC/DC converter with integrated supercaps

    Energy Technology Data Exchange (ETDEWEB)

    Ollhaeuser, Helmut [ALCOA/AFL Europe GmbH (Germany)

    2008-07-01

    In the light of increasing hybridization of future vehicle generations mainly those functionalities will be realized which contribute to fuel- and at the end emission-reduction. Recuperation, Start-Stop, E-steering and EDS-stabilization therefore constitute applications for which an efficient energy management has to be provided In this context ALCOA / AFL Europe GmbH developed a patent pending system solution, by which in one single unit a powerful DC/DC converter is integrated with the storage medium EDLC or Super-/Ultracap - on the one hand the restrictive packaging and on the other hand high performance requirements of the OEM can be met in a high degree. Possible issues arising from the compact integration of the supercaps such as heat dissipation and EMI are solved in a unique way - even the impacts in case of a defect cell are eliminated by a sophisticated balancing. The main performance characteristics of the current finished 1 KW solution being in test operation at various OEM are: - Output: 1 KW bidirectional - Capacity: 29,8 F / 12 Cells a 350 F - Additional fused power output - Optional output for consumers during motor start - Protection class IP 6K7 - Buck/Boost converter 2-phases - Operating frequency 125 kHz - Current control and phase monitoring realized in HW With its scaleable approach and the possibility to be integrated rapidly and cost-efficient in new carlines, the ECM just today combines the advantages of an intelligent electric power management. New prospective application-ranges - i.e. up to 5 KW for commercial vehicles and/or buses - are right now under development and clear its way for series implementation, soon. (orig.)

  1. Performance of a SOA-MZI wavelength converter for label swapping using combined FSK/IM modulation format

    DEFF Research Database (Denmark)

    Tafur Monroy, Idelfonso; Verdurmen, E. J. M.; Sulur, S.;

    2004-01-01

    for the header/payload, respectively. Experimental results are presented for a signaling scheme with payload data at 10 Gbit/s and an FSK label at 312 Mbit/s. Simulation results and measurements of the chirp properties of converted signals operating at data rates of 2.5 and 10 Gbit/s are presented. Conclusions......This paper presents a theoretical and experimental assessment of the performance of a wavelength converter based on semiconductor optical amplifiers (SOA) in a MZI configuration for optical label swapping. The optical labeling of the signal is based on an FSK/IM combined modulation format...... and design guidelines are presented regarding the implications of the wavelength converter performance on the quality of the label and payload signals for fast packet/burst forwarding in optically labeled switched networks. (C) 2063 Elsevier Inc. All rights reserved....

  2. A digital filter for an analog-digital converter with delta-sigma modulation

    Science.gov (United States)

    Beliavskaia, T. G.; Levchuk, Iu. P.; Strigina, E. V.

    1986-05-01

    Various methods of implementing the digital versions of analog-digital converters are examined, with attention given to homogeneous, triangular, and low-frequency digital filters. A comparison of the implementations proposed here makes it possible to optimize the structure of an analog-digital converter with respect to the hardware costs depending on the required accuracy.

  3. Analysis of a Multilevel Dual Active Bridge (ML-DAB DC-DC Converter Using Symmetric Modulation

    Directory of Open Access Journals (Sweden)

    M. A. Moonem

    2015-04-01

    Full Text Available Dual active bridge (DAB converters have been popular in high voltage, low and medium power DC-DC applications, as well as an intermediate high frequency link in solid state transformers. In this paper, a multilevel DAB (ML-DAB has been proposed in which two active bridges produce two-level (2L-5L, 5L-2L and 3L-5L voltage waveforms across the high frequency transformer. The proposed ML-DAB has the advantage of being used in high step-up/down converters, which deal with higher voltages, as compared to conventional two-level DABs. A three-level neutral point diode clamped (NPC topology has been used in the high voltage bridge, which enables the semiconductor switches to be operated within a higher voltage range without the need for cascaded bridges or multiple two-level DAB converters. A symmetric modulation scheme, based on the least number of angular parameters rather than the duty-ratio, has been proposed for a different combination of bridge voltages. This ML-DAB is also suitable for maximum power point tracking (MPPT control in photovoltaic applications. Steady-state analysis of the converter with symmetric phase-shift modulation is presented and verified using simulation and hardware experiments.

  4. MULTILEVEL CONVERTERS FOR MICROWELDING BASED ON M-ARY SYSTEM

    Directory of Open Access Journals (Sweden)

    Zhuikov V.

    2012-12-01

    Full Text Available Multilevel converter constructing and functioning principles are given. Two different approaches to increase efficiency are described. Both decisions are compared with typical applications, so advantages and drawbacks are specified.

  5. Converting VANDLE Data into ROOT for Merging with other Systems

    Science.gov (United States)

    Bergstrom, Z. J.; Kozub, R. L.; Peters, W. A.; Ikeyama, R.; Paulauskas, S. V.; Ahn, S.; Ribens Collaboration; Mona/LISA Collaboration; Vandle Collaboration

    2013-10-01

    During the rp-process in novae, nuclei rapidly capture protons to form heavier, proton-rich isotopes. Most of the rp-process reactions are believed to pass through the 56Ni(p , γ)57Cu(1106 keV) reaction which cannot be measured directly. In an experiment performed at the National Superconducting Cyclotron Laboratory (NSCL), the (d , n) proton transfer reaction in inverse kinematics at 35 MeV/nucleon was employed, primarily to determine the single particle strength of the 1106-keV (1/2-) level. In addition to their astrophysical significance, the measurements provide data for shell model calculations near doubly magic 56Ni. Two arrays of plastic scintillators, VANDLE and MoNA/LISA, were coupled in order to detect a wide range of neutron energies via the time-of-flight technique. Charged particle detectors placed in the focal plane of the NSCL Sweeper System were used to identify coincident 57Cu recoils, reducing random background events. VANDLE data from the experiment are being converted into ROOT trees so they can be merged with the charged particle data for analysis. Preliminary results and details of the (d , n) experimental setup will be presented. Research supported by the US DOE and NSF.

  6. A Carrier-Phase Control Suitable for Conducted EMI Noise Reduction in a Multiple-Converter System

    Science.gov (United States)

    Tamate, Michio; Toba, Akio; Matsumoto, Yasushi; Wada, Keiji; Shimizu, Toshihisa

    Conducted EMI noise flowing from the power converters to AC utility line is regulated by international commissions such as International Electrotechnical Commission (IEC). For adherence to the IEC regulations, EMI filters should be used in power electronics equipment. This paper proposes a method for analyzing the conducted EMI noise in multiple power converters connected to the same power line. In this method, the phase difference between sub-harmonic modulated carrier signals at each power converter is taken into account. The phase difference among the power converters determines the EMI noise level in a multiple-converter system, as is evident from the analysis of the waveform of the common-mode current. In addition, EMI noise suppression using a carrier-phase control is a proposed. In order to reduce volume of the EMI filter effectively, the phase difference θ should be set to 360/nN° here, n is a high-order harmonic component at around 150kHz, and N is the number of power converters. Therefore, the conducted EMI noise can be reduced effectively with the help of the proposed phase control.

  7. Wind Energy Conversion System with Boost Converter and CHB MLI with single DC input

    Directory of Open Access Journals (Sweden)

    Porselvi T

    2014-03-01

    Full Text Available The developments in power electronics technology have led to the developments in the wind energy conversion system (WECS. The output voltage of the WECS depends on the speed of the wind, which is not constant. Hence, a power conversion unit is required to maintain the output voltage of the WECS constant. This paper presents the design of a boost converter and a voltage controller for maintaining the DC-link voltage of the system constant. A new topology of the cascaded H-bridge multilevel inverter (CHB MLI is proposed for the DC/ AC conversion. The proposed topology eliminates the requirement of separate DC sources. The multilevel inverter is controlled by the selective harmonic elimination pulse width modulation (SHE-PWM technique. The system is simulated in MATLAB/ Simulink for varying wind speeds. The simulated waveforms of the PMSG rotor speed, the PMSG voltage, the boost converter voltage and the CHBMLI voltages are shown and the results obtained are found to be satisfactory.

  8. A Modulated Hybrid Filter Bank for Wide-Band Analog-to-Digital Converters

    Directory of Open Access Journals (Sweden)

    Chunyan Yuan

    2014-04-01

    Full Text Available It is difficult to use a single analog-to-digital conversion (ADC to satisfy the requirements for conversion of an ultra-wideband signal. A parallel architecture for high bandwidth ADC, named cosine modulated hybrid filter bank, is presented to address this problem. First, the proposed architecture shifts the input signal spectrum by means of mixers. The modulated signal is channelized into smaller frequency subband signals using identical lowpass analog filters. Then the subband signals are digitized through identical narrowband ADCs, respectively. Finally, the digitized signals are up-sampled, then filtered and combined to reconstruct the digital representation of the original wide-band input signal. The digital filters are designed to use the eigenfilter method based on total least squares error criterion. Since the sample-and-hold circuits needed are only identical narrowband baseband circuits, the simplicity of the system makes the design easier and cheaper. Several design examples are used to illustrate the performance of the proposed system.

  9. Individual Module Maximum Power Point Tracking for a Thermoelectric Generator Systems

    DEFF Research Database (Denmark)

    Vadstrup, Casper; Chen, Min; Schaltz, Erik

    Thermo Electric Generator (TEG) modules are often connected in a series and/or parallel system in order to match the TEG system voltage with the load voltage. However, in order to be able to control the power production of the TEG system a DC/DC converter is inserted between the TEG system...... and the load. The DC/DC converter is under the control of a Maximum Power Point Tracker (MPPT) which insures that the TEG system produces the maximum possible power to the load. However, if the conditions, e.g. temperature, health, etc., of the TEG modules are different each TEG module will not produce its...... maximum power. The result of the system MPPT is therefore the best compromise of all the TEG modules in the system. On the other hand, if each TEG module is controlled individual, each TEG module can be operated in its maximum power point and the TEG system output power will therefore be higher...

  10. A Traction Three-Phase to Single-Phase Cascade Converter Substation in an Advanced Traction Power Supply System

    Directory of Open Access Journals (Sweden)

    Xiaoqiong He

    2015-09-01

    Full Text Available The advanced traction power supply system (ATPSS is a new directional development for traction power supply systems, which can totally remove the neutral sections and effectively promote power quality. However, the existing converters suffer from small substation capacity. In this paper, a new configuration based on a three-level neutral point clamped (3L-NPC three-phase to single-phase cascade converter in a substation is proposed for ATPSS, which can be used to match the capacity of the converter for high voltage and large power applications. The control strategy of the proposed converter is analyzed in depth, and the phase disposition sinusoidal pulse width modulation (PD-SPWM with phase shift carrier SPWM (PSC-SPWM is employed in the inverters. Then, the inductance equalizing circuit is applied for the voltage balance on the DC-link. Besides, a LC filter circuit is designed to eliminate the double line-frequency ripple of DC voltage. Afterwards, a simulation model and an experimental prototype are developed, respectively. The simulation results show that the proposed converter in this paper can not only meet the requirements of voltage and capacity for the traction network, but also improve power quality. Finally, the experimental results verify the correctness and feasibility of the proposed control strategy.

  11. Development of a standardized control module for dc-to-dc converters

    Science.gov (United States)

    Yu, Y.; Iwens, R. I.; Lee, F. C.; Inouye, L. Y.

    1977-01-01

    The electrical performance of a power processor depends on the quality of its control system. Most of the existing control circuits suffer one or more of the following imperfections that tend to restrict their respective utility: (1) inability to perform different modes of duty cycle control; (2) lack of immunity to output filter parameter changes, and (3) lack of capability to provide power component stress limiting on an instantaneous basis. The three lagging aspects of existing control circuits have been used to define the major objectives of the current Standardized Control Module (SCM) Program. Detailed information on the SCM functional block diagram, its universality, and performance features, circuit description, test results, and modeling and analysis efforts are presented.

  12. Analysis and Design of CLL Resonant Converter for Solar Panel-battery Systems

    Directory of Open Access Journals (Sweden)

    D.Ramasubramanian

    2012-12-01

    Full Text Available This paper presents a CLL resonant converter with DSP based Fuzzy Logic Controller (FLC for solar panel to battery charging system. The mathematical model of the converters has been developed and simulated using MATLAB. The state space model of the converter is developed; it is used to analysis the steady state stability of the system. The aim of the proposed converter is to regulate and control of the output voltage from the solar panel voltage. The performance of the proposed converter is validated through experiments with a 75-Watt solar panel. The effectiveness of the controller is verified for supply change and load disturbance. The converter is implemented on a TMS320F2407 Digital Signal Processor with 75-Watt PV system. Comparison between experimental and simulations show a very good agreement and the reliability of fuzzy controller.

  13. Cascaded Thermoelectric Converters for Advanced Radioisotope Power Systems

    Science.gov (United States)

    El-Genk, Mohamed S.; Saber, Hamed H.

    2004-02-01

    Three Cascaded Thermoelectric Converters (CTCs) are optimized for potential use in Multi-Mission Advanced Radioisotope Power Systems (MM-ARPS) for electrical powers up to 1 kWe, or even higher, in support of 7-10 year missions. The peak efficiencies of these CTCs of 9.43% to 14.32% are 40% to 110% higher than that of SiGe in State-of-the-Art (SOA) Radioisotope Thermoelectric Generators (RTGs). Such high efficiencies would significantly reduce the amount of 238PuO2 fuel and the total system mass for a lower mission cost. Each CTC is comprised of a SiGe top unicouple that is thermally, but not electrically, coupled to a bottom unicouple with one of the following three choices of thermoelectric materials: (a) p-leg of TAGS-85 and n-leg of 2N-PbTe (b) p-leg of CeFe3.5Co0.5Sb12 and n-leg of CoSb3; and (c) segmented p-leg of CeFe3.5Co0.5Sb12 and Zn4Sb3 and n-leg of CoSb3. The length of the top and bottom unicouples is 10 mm, but the cross-sectional areas of the n- and p-legs of the unicouples are optimized for maximum efficiency operation. They vary with the thermal power inputs of 1, 2, and 3 Wth per SiGe unicouple, and the heat rejection temperature of 375 K, 475 K, and 575 K, from the bottom unicouple. Such geometrical optimization is at nominal hot shoe temperature of 1273 K for the SiGe unicouple and cold shoe temperature of either 780 K or 980 K, depending on the materials of the bottom unicouples. The hot shoe temperature of the bottom unicouples is 20 K lower than the cold shoe of the top SiGe unicouple, but the rate of heat input is the same as the rate of heat rejection from the top unicouple. The present results are conservative as they assume a contact resistance of 150 μΩ-cm2 per leg for the top and the bottom unicouples in the CTCs; however, decreasing this resistance to 50 μΩ-cm2 per leg could increase the current efficiency estimates by an additional 1 - 2 percentage points.

  14. A new perspective in power converters modelling : complementarity systems

    NARCIS (Netherlands)

    Vasca, Francesco; Iannelli, Luigi; Çamlıbel, Kanat

    2007-01-01

    Switched complementarity framework is proposed as an useful and simple way for modelling the dynamic behavior of power electronics converters. The voltage/current characteristic of each electronic device in each conducting state is assumed to be representable in piecewise linear form. It is shown ho

  15. All optical up-converted signal generation with high dispersion tolerance using frequency quadrupling technique for radio over fiber system

    Science.gov (United States)

    Gu, Yiying; Zhao, Jiayi; Hu, Jingjing; Kang, Zijian; Zhu, Wenwu; Fan, Feng; Han, Xiuyou; Zhao, Mingshan

    2016-05-01

    A novel all optical up-converted signal generation scheme with optical single-sideband (OSSB) technique for radio over fiber (RoF) application is presented and experimentally demonstrated using low-bandwidth devices. The OSSB signal is generated by one low-bandwidth intensity LiNbO3 Mach-Zehnder modulator (LN-MZM) under frequency quadrupling modulation scheme and one low-bandwidth LN-MZM under double sideband carrier suppressed modulation (DSB-CS) scheme. The proposed all OSSB generation scheme is capable of high tolerance of fiber chromatic dispersion induced power fading (DIPF) effect. Benefiting from this novel OSSB generation scheme, a 26 GHz radio frequency (RF) signal up-conversion is realized successfully when one sideband of the optical LO signal is reused as the optical carrier for intermediate frequency (IF) signal modulation. The received vector signal transmission over long distance single-mode fiber (SMF) shows negligible DIPF effect with the error vector magnitude (EVM) of 15.7% rms. In addition, a spurious free dynamic range (SFDR) of the OSSB up-converting system is measured up to 81 dB Hz2/3. The experiment results indicate that the proposed system may find potential applications in future wireless communication networks, especially in microcellular personal communication system (MPCS).

  16. Development and implementation of a compound converter in solar energy systems

    Directory of Open Access Journals (Sweden)

    S. J. B. Hartman

    1992-07-01

    Full Text Available The converter proposed here is a compound photovoltaic converter system that has been implemented with a power rating of 1,5 kVA at an array voltage of 96 V, using a 24 V battery bank. The converter system combines the functions of inversion, battery regulation and maximum power point tracking of the solar array into a single cost-effective converter. Maximum power point tracking is performed by controlling the voltage and frequency of the AC output. A description of this converter, and an explanation of the control strategy employed, are provided together with practical results measured on the prototype converter. This compound topology has a high conversion efficiency from solar array to load.

  17. Modulation schemes with enhanced switch thermal distribution for single-phase AC-DC-AC reduced-switch converters

    DEFF Research Database (Denmark)

    Qin, Zian; Loh, Poh Chiang; Blaabjerg, Frede

    2015-01-01

    ulation schemes can significantly change the performance of a power converter in steady state, and they have been extensively studied, but mostly directed to three-phase topologies, where triplen offsets are added. Single-phase systems, including ac-dc-ac systems, are less widely pursued, even...... among their switches, while keeping their dc-link voltages low. Single points of failure are thus minimized, allowing the converters to have longer lifetimes. Simulation and experimental results have demonstrated the intended performances and hence verifying the idea....

  18. Virtual-vector-based space vector pulse width modulation of the DC-AC multilevel-clamped multilevel converter (MLC2)

    DEFF Research Database (Denmark)

    Rodriguez, Pedro; Busquets-Monge, Sergio; Blaabjerg, Frede;

    2011-01-01

    This work presents the development of the space vector pulse width modulation (SVPWM) of a new multi-level converter topology. First, the proposed converter and its natural space vector diagram are presented. Secondly, a modified space vector diagram based on the virtual-vectors technique is show...

  19. Innovative measuring system for wear-out indication of high power IGBT modules

    DEFF Research Database (Denmark)

    Nielsen, Rasmus Ørndrup; Due, Jens; Munk-Nielsen, Stig

    2011-01-01

    Power converter failures are a major issue in modern Wind turbines. One of the key elements of power converters for high power application is the IGBT modules. A test bench capable of performing an accelerated wear-out test through power cycling of IGBT modules has been made. In the test bench...... it is possible to stress the IGBT module in a real life working point, controlling the voltage, current and phase of the device under test. An analysis of failure mechanisms has been carried out, indicating that VCE can be used as an sign of wear out of the IGBT module. Therefore an innovative measuring system...

  20. Fault Diagnosis and Fault-tolerant Control of Modular Multi-level Converter High-voltage DC System

    DEFF Research Database (Denmark)

    Liu, Hui; Ma, Ke; Wang, Chao

    2016-01-01

    Modular Multilevel Converter based High Voltage Direct Current (MMC-HVDC) configuration is a promising solution for the efficient grid integration and bulky power transmission over long distance. However, the large number of series connected identical modules in MMC may increase the probability...... strategies of MMC-HVDC systems for the most common faults happened in MMC-HVDC systems covering MMC faults, DC side faults as well as AC side faults. An important part of this paper is devoted to a discussion of the vulnerable spots as well as failure mechanism of the MMC-HVDC system covering switching...

  1. Control and modulation for loss minimization for dc/dc converters in wind farm

    DEFF Research Database (Denmark)

    Dincan, Catalin Gabriel; Kjær, Philip Carne

    2016-01-01

    For a DC wind turbine, a single phase series-resonant converter for unidirectional power is studied. This paper aims to identify and compare impact on electrical losses and component ratings from the choice of three candidate control strategies. The evaluation is purely based on circuit simulatio...

  2. Design and Implementation of A/D Converter Module in Industry%工业通用A/D采集模块的设计与实现

    Institute of Scientific and Technical Information of China (English)

    赵建敏; 李琦

    2012-01-01

    Analog signal acquisition and convertion is an essential part of industry process control system. Based on μCOS - Ⅱ realtime operation system and Modbus protocol, the design of AD converter module using STM32 was presented. The analog signal from sensor was converted to digital using the ADC of STM32. The data is then sent to RS - 485 bus to the master. The module works on Modbus RTU mode and can be expediently added to any data acquisition system based on Modbus protocol. It has been u-sing in heat net control system and fulfils the requirements.%模拟量参数的采集及转换是工业过程控制的重要组成.文中采用STM32单片机,设计了基于μCOS-Ⅱ实时操作系统、支持Modbus通讯协议的通用ADC模块.传感器模拟信号通过输入通道送入STM32的ADC端口进行AD转换,转换结果通过RS-485发送到RS485总线.模块支持Modbus通讯协议,工作在RTU模式,可方便地应用于采用Mod-bus协议构建的工业数据采集系统中.该模块已经在某市热网监控系统中使用,完全符合控制要求.

  3. Earth System Science Education Modules

    Science.gov (United States)

    Hall, C.; Kaufman, C.; Humphreys, R. R.; Colgan, M. W.

    2009-12-01

    The College of Charleston is developing several new geoscience-based education modules for integration into the Earth System Science Education Alliance (ESSEA). These three new modules provide opportunities for science and pre-service education students to participate in inquiry-based, data-driven experiences. The three new modules will be discussed in this session. Coastal Crisis is a module that analyzes rapidly changing coastlines and uses technology - remotely sensed data and geographic information systems (GIS) to delineate, understand and monitor changes in coastal environments. The beaches near Charleston, SC are undergoing erosion and therefore are used as examples of rapidly changing coastlines. Students will use real data from NASA, NOAA and other federal agencies in the classroom to study coastal change. Through this case study, learners will acquire remotely sensed images and GIS data sets from online sources, utilize those data sets within Google Earth or other visualization programs, and understand what the data is telling them. Analyzing the data will allow learners to contemplate and make predictions on the impact associated with changing environmental conditions, within the context of a coastal setting. To Drill or Not To Drill is a multidisciplinary problem based module to increase students’ knowledge of problems associated with nonrenewable resource extraction. The controversial topic of drilling in the Arctic National Wildlife Refuge (ANWR) examines whether the economic benefit of the oil extracted from ANWR is worth the social cost of the environmental damage that such extraction may inflict. By attempting to answer this question, learners must balance the interests of preservation with the economic need for oil. The learners are exposed to the difficulties associated with a real world problem that requires trade-off between environmental trust and economic well-being. The Citizen Science module challenges students to translate scientific

  4. Reliability Improvement of Power Converters by Means of Condition Monitoring of IGBT Modules

    DEFF Research Database (Denmark)

    Choi, Ui Min; Blaabjerg, Frede; Jørgensen, Søren

    2017-01-01

    proposes a condition monitoring method of insulated-gate bipolar transistor (IGBT) modules. In the first section of this paper, a structure of a conventional IGBT module and a related parameter for the condition monitoring are explained. Then, a proposed real-time on-state collector-emitter voltage...

  5. Open-switch fault detection method of an NPC converter for wind turbine systems

    DEFF Research Database (Denmark)

    Lee, June-Seok; Lee, Kyo-Beum; Blaabjerg, Frede

    2013-01-01

    In wind turbine generation (WTG) systems, the neutral-point-clamped (NPC) topology is widely used as the part of a back-to-back converter since the three-level NPC topology has more advantages than the conventional two-level inverter especially for high power. There are twelve switches in the NPC...... topology and an open-switch fault of the NPC converter leads to current distortion and the torque ripple in the system. Furthermore, WTG systems can breakdown in the worst case by this ripple. To improve the reliability of WTG systems, an open-switch fault detection method is required. The open......-switch detection method of the NPC converter is different from that of the NPC inverter due to the different current paths of the NPC converter. This paper proposes the open-switch fault detection method of the NPC converter connected the permanent-magnet synchronous generator (PMSG). Moreover, the open...

  6. Swarming Speed Control for DC Permanent Magnet Motor Drive via Pulse Width Modulation Technique and DC/DC Converter

    Directory of Open Access Journals (Sweden)

    A.S. Oshaba

    2013-05-01

    Full Text Available This study presents an approach for the speed control of a permanent magnet DC motor drive via Pulse Width Modulation (PWM technique and a DC/DC converter. The Particle Swarm Optimization (PSO technique is used to minimize a time domain objective function and obtain the optimal controller parameters. The performance of the proposed technique has been evaluated using various types of disturbances including load torque variations. Simulation results illustrate clearly the robustness of the controller and validity of the design technique for controlling the speed of permanent magnet motors.

  7. Coupled Inductor Based High Step-Up DC-DC Converter for Multi Input PV System

    Directory of Open Access Journals (Sweden)

    G. Shiny Vikram

    2014-09-01

    Full Text Available With the shortage of the energy and ever increasing of the oil price, research on the renewable and green energy sources, especially the solar arrays and the fuel cells, becomes more and more important. How to achieve high step-up and high efficiency DC/DC converters is the major consideration in the renewable power applications due to the low voltage of PV arrays and fuel cells. In this paper a coupled inductor dc-dc converter for photovoltaic system is proposed. The circuit configuration of the proposed converter is very simple. Thus, the proposed converter has higher step-up and step-down voltage gains than the conventional bidirectional dc–dc boost/buck converter. Under same electric specifications for the proposed converter and the conventional bidirectional boost/buck converter, the average value of the switch current in the proposed converter is less than the conventional bidirectional boost/buck converter. The operating principles have been applied to multi input photovoltaic system and outputs have been observed.

  8. A Categorization of Converter Station Controllers Within Multi-terminal DC Transmission Systems

    DEFF Research Database (Denmark)

    Irnawan, Roni; Silva, Filipe Miguel Faria da; Bak, Claus Leth;

    2016-01-01

    As more and more VSC-HVDC links are planned and commissioned, interconnection of neighboring links or connection to an existing link becomes a feasible step towards secure and reliable multi-terminal DC (MTDC) transmission systems. Multi-vendor MTDC (MV-MTDC) operation is anticipated as an impact...... of this gradual DC grids development. In order to achieve certain operation conditions, DC grid controller needs to send specific control settings to individual converter station controls. One of the challenges in MV-MTDC transmission systems occurs in coordination of converters since different types...... of controller might exist in the same system. It is therefore important to identify the parameters required by the converter station controllers to ensure a smooth coordination. In this paper, different converter station controllers available in the literatures are categorized. Challenges of converter station...

  9. Health Occupations Module. The Integumentary System.

    Science.gov (United States)

    Temple Univ., Philadelphia, PA. Div. of Vocational Education.

    This module on the integumentary system is one of eight modules designed for individualized instruction in health occupations education programs at both the secondary and postsecondary levels. This module contains an introduction to the module topic, objectives (e.g., list and describe the types of glands formed in the skin, and explain the…

  10. Choosing the number of readout systems of a photoelectric angle converter

    Science.gov (United States)

    Latyev, S. M.; Mitrofanov, S. S.

    1994-09-01

    This paper discusses certain errors of photoelectric angle converters whose effect can be lessened by making the best choice of the number of readout systems and of their definite mutual placement. Recommendations are given for compensating the systematic and random errors of a converter.

  11. Choosing the number of readout systems of a photoelectric angle converter

    Energy Technology Data Exchange (ETDEWEB)

    Latyev, S.M.; Mitrofanov, S.S. [Institute of Precision Mechanics and Optics, St. Petersburg (Russian Federation)

    1994-09-01

    This paper discusses certain errors of photoelectric angle converters whose effect can be lessened by making the best choice of the number of readout systems and of their definite mutual placement. Recommendations are given for compensating the systematic and random errors of a converter. 4 refs.

  12. Protection of Hardware: Powering Systems (Power Converter, Normal Conducting, and Superconducting Magnets)

    CERN Document Server

    Pfeffer, H; Wolff, D

    2016-01-01

    Along with the protection of magnets and power converters, we have added a section on personnel protection because this is our highest priority in the design and operation of power systems. Thus, our topics are the protection of people, power converters, and magnet loads (protected from the powering equipment), including normal conducting magnets and superconducting magnets.

  13. Design of coolant distribution system (CDS) for ITER PF AC/DC converter

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Bin [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Song, Zhiquan, E-mail: zhquansong@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Fu, Peng; Xu, Xuesong; Li, Chuan [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Wang, Min; Dong, Lin [China International Nuclear Fusion Energy Program Execution Center, Beijing 100862 (China)

    2016-10-15

    Highlights: • System process and arrangement has been proposed to meet the multiple requirements from the converter system. • Thermal hydraulic analysis model has been developed to size and predict the system operation behavior. • Prototype test has been performed to validate the proposed design methodology. - Abstract: The Poloidal Field (PF) converter unit, playing an essential role in the plasma shape and position control in vertical and horizontal direction, which is an important part of ITER power supply system. As an important subsystem of the converter unit, the coolant distribution system has the function to distribute the cooling water from ITER component cooling water system (CCWS) to its main components at the required flow rate, pressure and temperature. This paper presents the thermal hydraulic design of coolant distribution system for the ITER PF converter unit. Different operational requirements of the PF converter unit regarding flow rate, temperature and pressure have been analyzed to design the system process and arrangement. A thermal-hydraulic analysis model has been built to size the system and predict the flow rate and temperature distribution of the system under the normal operation. Based on the system thermal-hydraulic analysis results, the system pressure profile has been plotted to evaluate the pressure behavior along each client flow path. A CDS prototype for the ITER PF converter has been constructed and some experiments have been performed on it. A good agreement of the flow distribution and temperature behavior between the simulated and test results validate the proposed design methodology.

  14. Systems Approach for Designing Cordierite Ceramic Converters for Automotive Emissions Control

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The successful application of porous cordierite ceramic monolithic converters for automotive emissions control over the past 24 years in North America has been attributed to systems approach for optimizing the total converter package from reliability point of view. The systems approach examines the interaction between various components of monolithic converter package, namely the cordierite substrate, the alumina washcoat, the braided wire-rope end seals, the intumescent ceramic mat or steel wiremesh, and the stainless steel can, from long-term durability point of view. Such an approach has also proven successful in the Japanese, European, Korean and South American automotive industries. The key objectives of this paper are: i) to describe Corning′s methodology for assessing the impact of alumina washcoat on mechanical and thermal integrities of cordierite converter; ii) to examine the impact of mount density of ceramic mat or steel wiremesh on containment of cordierite converter against engine vibrations, gas pulsations and thermal gradients, and; iii) to analyze the impact of can design on strength and thermal shock resistance of cordierite converter. The above objectives will be illustrated by several examples of successful converter design for automobiles. This paper also addresses the Chinese automotive converter requirements and how they might be met via systems approach.

  15. Integrated PWM converter/inverter system feeding three-phase induction motor

    Energy Technology Data Exchange (ETDEWEB)

    Bayoumi, E.

    2001-07-01

    The integrated PWM converter/inverter system has the capability of unity power factor, sinusoidal supply current, bi-directional power capabilities and constant dc link voltage. Also, it has the ability to minimize the dc link capacitance. The integrated PWM converter/inverter fed three-phase induction motor consists of two identical PWM converters. One is used to serve as power regulator with unity power factor and constant dc voltage bus, while the other serve as inverter for the induction motor drive. By using the synchronous rotating-frame the current controllers in both the input and the output of the integrated system are characterized by fast current response and low harmonic distortion. The dc link is the intermediate stage between the PWM converter and the PWM inverter. It mainly consists of aluminium electrolytic capacitors, which are normally installed in the system as the energy storage element, but in some applications, such as high power voltage motor drives, the electrolytic capacitor has several drawbacks from the viewpoints of size, weight, cost and reliability. Due to continuous outgassing, the properties of the electrolytic capacitor deteriorate gradually (as time goes by). Hence, the capacitor is the major factor limiting the lifetime of the inverter systems. The aim of this work is to reduce the dc link capacitor size, as it means reduction of the cost and the volume of the converter/inverter systems. The work consists of 8 chapters: Chapter one illustrate the historical overview for the ac/dc/ac fed induction motor drive systems. It describes the benefits of the integrated PWM converter/inverter fed induction motor drive. It classified the integrated PWM converter/inverter systems into two types independent and dependent systems. It demonstrates some ideas for the control algorithms of these types of integrated systems. Chapter two introduces the mathematical model for the PWM converter. It explains the space vector PWM (SVPWM) method for

  16. Ac-dc Bus-interface Bi-directional Converters in Renewable Energy Systems

    OpenAIRE

    Dong, Dong

    2012-01-01

    This dissertation covers several issues related to the ac-dc bus-interface bi-directional converters in renewable energy systems. The dissertation explores a dc-electronic distribution system for residential and commercial applications with a focus on the design of an ac-dc bi-directional converter for such application. This converter is named as the â Energy Control Centerâ due to its unique role in the system. First, the impact of the unbalanced power from the ac grid, especially the ...

  17. Practical Implementation of Embedded Controlled Boost Converter for Solar Installation System

    Directory of Open Access Journals (Sweden)

    A. Kalirasu

    2010-08-01

    Full Text Available The solar photovoltaic power has received great attention and experienced impressive progress in the countries all over the world in recent years because of more and more serious energy crisis and environmental pollution. This paper proposes a Embedded controlled boost converter for solar installation system. Boost converter system is simulated using Matlab and it is implemented using embedded controller. The simulation and experimental results of this system are presented and compared. This converter has advantages like improved power factor, fast response and reduced hardware.

  18. Efficient and ripple-mitigating dc-dc converter for residential fuel cell system

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yong [Danfoss Solar Inverters, Hardware, Jyllandsgade 28, 6400 Soenderborg (Denmark); Choi, Seeyoung [Digital Appliance Division, Samsung Electronics Co. Ltd., Maetan-3Dong, Suwon, Gyeonggi (Korea); Lee, Eunchul [Willings Co. Ltd., SK Ventium, 522 Dangjung-Dong, Gunpo-Si, Gyeonggi-Do (Korea)

    2009-01-15

    Proton exchange membrane fuel cell (PEMFC) systems for residential application require efficient and ripple-mitigating power conditioning system (PCS). The key point to reach it, is the design and control of the dc-dc converter. Based on the theoretical and experimental analysis of the traditional converter, this paper proposes a novel parallel-series full bridge (P-SFB) dc-dc converter, and improves its phase shifting scheme. This paper also proposes a novel controller for low frequency ripple current suppressing applied on the converter. The experimental results verify that, the dc-dc converter achieves a peak efficiency of 95.5%. Therefore PCS's maximum efficiency reaches 92.9%. And the input current ripple is reduced significantly with the new controller. (author)

  19. High-Repeatable Data Acquisition Systems for Pulsed Power Converters in Particle Accelerator Structures

    CERN Document Server

    AUTHOR|(CDS)2087245; Martino, Michele; Zinno, Raffaele

    In this Ph.D. thesis, the issues related to the metrological characterization of high-performance pulsed power converters are addressed. Initially, a background and a state of the art on the measurement systems needed to correctly operate a high-performance power converter are presented. As a matter of fact, power converters usually exploits digital control loops to enhance their performance. In this context the final performance of a power converter has to be validated by a reference instrument with higher metrological characteristics. In addition, an on-line measurement systemis also needed to digitize the quantity to be controlled with high accuracy. Then, in industrial applications of power converters metrology, specifications are given in terms of Worst-Case Uncertainty (WCU). Therefore, an analytical model for predicting the Worst-Case Uncertainty (WCU) of a measurement system is discussed and detailed for an instrument affected by Gaussian noise. Furthermore, the study and the design of a Reference Acq...

  20. Coherent combining of fiber-laser-pumped frequency converters using all fiber electro-optic modulator for active phase control

    Science.gov (United States)

    Bourdon, P.; Durécu, A.; Canat, G.; Le Gouët, J.; Goular, D.; Lombard, L.

    2015-03-01

    Coherent beam combining (CBC) by active phase control could be useful for power scaling fiber-laser-pumped optical frequency converters like OPOs. However, a phase modulator operating at the frequency-converted wavelength is needed, which is non standard component. Fortunately, nonlinear conversion processes rely on a phase-matching condition correlating, not only the wave vectors of the coupled waves, but also their phases. This paper demonstrates that, using this phase correlation for indirect control of the phase, coherent combining of optical frequency converters is feasible using standard all-fibered electro-optic modulators. For the sake of demonstration, this new technique is experimentally applied twice for continuous wave second-harmonic-generator (SHG) combination: i) combining 2 SHG of 1.55-μm erbium-doped fiber amplifiers in PPLN crystals generating 775-nm beams; ii) combining 2 SHG of 1.064-μm ytterbium-doped fiber amplifiers in LBO crystals generating 532-nm beams. Excellent CBC efficiency is achieved on the harmonic waves in both these experiments, with λ/20 and λ/30 residual phase error respectively. In the second experiment, I/Q phase detection is added on fundamental and harmonic waves to measure their phase variations simultaneously. These measurements confirm the theoretical expectations and formulae of correlation between the phases of the fundamental and harmonic waves. Unexpectedly, in both experiments, when harmonic waves are phase-locked, a residual phase difference remains between the fundamen tal waves. Measurements of the spectrum of these residual phase differences locate them above 50 Hz, revealing that they most probably originate in fast-varying optical path differences induced by turbulence and acoustic-waves on the experimental breadboard.

  1. A Modified C-Dump Converter for BLDC Machine Used in a Flywheel Energy Storage System

    Directory of Open Access Journals (Sweden)

    Bandaru Ramakrishna

    2014-10-01

    Full Text Available This paper presents a modified C-dump converter for brushless DC (BLDC machine used in the flywheel energy storage system. The converter can realize the energy bidirectional flowing and has the capability to recover the energy extracted from the turnoff phase of the BLDC machine. The principle of operation, modeling, and control strategy of the system has been investigated in the paper. Simulation and experimental results of the proposed system are also presented and discussed.

  2. Optimization with System Damping Restoration for Droop Controlled DC-DC Converters

    DEFF Research Database (Denmark)

    Meng, Lexuan; Dragicevic, Tomislav; Guerrero, Josep M.

    2013-01-01

    the efficiency of the conversion system, this paper implements tertiary level optimization control on the basis of hierarchical control. As the efficiency of each converter changes with output power, VRs are set as decision variables for adjusting power sharing proportion among converters. Genetic algorithm...... restoration (SDSR) is implemented to readjust the optimization results so as to ensure system stability. Simulation results are shown to demonstrate the improvement of system efficiency and effectiveness of the method....

  3. Modular space-vector pulse-width modulation for nine-switch converters

    DEFF Research Database (Denmark)

    Dehghan, Seyed Mohammad; Amiri, Arash; Mohamadian, Mustafa

    2013-01-01

    Recently, nine-switch inverter (NSI) has been presented as a dual-output inverter with constant frequency (CF) or different frequency (DF) operation modes. However, the CF mode is more interesting because of its lower switching device rating. This study proposes a new space-vector modulation (SVM...

  4. Junction temperature estimation method for a 600 V, 30A IGBT module during converter operation

    DEFF Research Database (Denmark)

    Choi, U. M.; Blaabjerg, F.; Iannuzzo, F.

    2015-01-01

    This paper proposes an accurate method to estimate the junction temperature using the on-state collector-emitter voltage at high current. By means of the proposed method, the estimation error which comes from the different temperatures of the interconnection materials in the module is compensated...

  5. Compact DC-DC Converter for Pocket Micro-Controller Systems

    Institute of Scientific and Technical Information of China (English)

    1996-01-01

    Novel compact DC-C converters for pocket micro-controller systems are discussed in the paper,which are based on switched capcotprs and inductorless,consequently are more suitable for being hybridized.The new converters enable the pocket microcontroller system to be powered by only one+12V source,while+5V and -12V are converted from the +12V source.The basic principle,voltage ratio,efficiency and ripples are analysed.Experiment and SPICE simulation are also given,which show positive results.

  6. Modular Power System Configured with Standard Product Hybrid DC-DC Converters Project

    Data.gov (United States)

    National Aeronautics and Space Administration — VPT proposes an innovative concept whereby complex NASA space power electronic systems can be configured using a small number of qualified hybrid DC-DC converter and...

  7. SYSTEM FOR TORQUE CONVERTER DESIGN AND ANALYSIS BASED ON CAD/CFD INTEGRATED PLATFORM

    Institute of Scientific and Technical Information of China (English)

    WU Guangqiang; YAN Peng

    2008-01-01

    A 3D torque converter design system is developed based on numerical investigation into flow field and CAD technology. The 3D steady-state flow field simulation is undertaken by using time averaged Reynolds equation and k-epsilon turbulence model, with mixing-plane boundary conditions at three section interfaces. The blades are designed according to the flow field characteristics by using a reverse design method in the system. The accurateness of numerical analysis and the validity of design system are verified by the fluid field experiment of desingn example of the torque converter. This kind of design and analysis system for torque converter based on integration of comput ationol fluid dynamics (CFD) and CAD is a powerful tool for torque converter manufacturing, but also a prettg important significance for research and development.

  8. Modular Power System Configured with Standard Product Hybrid DC-DC Converters Project

    Data.gov (United States)

    National Aeronautics and Space Administration — VPT proposes an innovative concept whereby complex, multiple-output, DC-DC converter systems can be configured through use of only 2 standard product hybrid DC-DC...

  9. Unified active and reactive power modulation of HVDC transmission systems

    Science.gov (United States)

    Grund, C. E.; Pohl, R. V.

    1981-11-01

    The power modulation of a high voltage direct current (HVDC) system for stabilization of an ac/dc network was investigated. It was found that simultaneous modulation of both dc current and voltage was more effective than just current modulation by itself, since the dc voltage modulation could be used to minimize the reactive power changes resulting from a change of the dc current. This helps stabilize the ac busbar voltages at the converters, which reduces undesirable load flow changes to voltage dependent ac loads, thus improving the effectiveness of the dc power modulation. This unified modulation control concept was evaluated by means of digital computer studies as well as a special purpose HVDC simulator. Several combined ac/dc power transmission systems were synthesized for testing of different modulation controller concepts. An optimum controller design incorporating a linear quadratic control algorithm with full state feedback was first studied. This provided a basis for comparison of suboptimal controller designs utilizing reduced state feedback and a Kalman filter state reconstruction technique.

  10. Model of Bi-directional Flyback Converter for Hybrid AC/DC Distribution System

    Directory of Open Access Journals (Sweden)

    Riku Pasonen

    2013-12-01

    Full Text Available In this article, a simulation model and concept of two switch bi-directional isolated DC/DC converter is presented. Converter is based on flyback converter type. Also control method for voltage regulation with bi-directional power transfer is presented. Target application of the proposed converter was selected to be a hybrid AC/DC distribution system concept of which was briefly described. The requirement of galvanic isolation in the hybrid AC/DC concept comes from use of shared neutral wire; DC current runs with unbalanced part of AC current in neutral wire. Without galvanic isolation grounded neutral would cause short circuit if DC/DC converter is connected to three phase rectifier or inverter. Simulation was carried out with PSCAD electromagnetic transient simulator.

  11. Designing and Testing Composite Energy Storage Systems for Regulating the Outputs of Linear Wave Energy Converters

    Directory of Open Access Journals (Sweden)

    Zanxiang Nie

    2017-01-01

    Full Text Available Linear wave energy converters generate intrinsically intermittent power with variable frequency and amplitude. A composite energy storage system consisting of batteries and super capacitors has been developed and controlled by buck-boost converters. The purpose of the composite energy storage system is to handle the fluctuations and intermittent characteristics of the renewable source, and hence provide a steady output power. Linear wave energy converters working in conjunction with a system composed of various energy storage devices, is considered as a microsystem, which can function in a stand-alone or a grid connected mode. Simulation results have shown that by applying a boost H-bridge and a composite energy storage system more power could be extracted from linear wave energy converters. Simulation results have shown that the super capacitors charge and discharge often to handle the frequent power fluctuations, and the batteries charge and discharge slowly for handling the intermittent power of wave energy converters. Hardware systems have been constructed to control the linear wave energy converter and the composite energy storage system. The performance of the composite energy storage system has been verified in experiments by using electronics-based wave energy emulators.

  12. An overview of power electronics applications in fuel cell systems: DC and AC converters.

    Science.gov (United States)

    Ali, M S; Kamarudin, S K; Masdar, M S; Mohamed, A

    2014-01-01

    Power electronics and fuel cell technologies play an important role in the field of renewable energy. The demand for fuel cells will increase as fuel cells become the main power source for portable applications. In this application, a high-efficiency converter is an essential requirement and a key parameter of the overall system. This is because the size, cost, efficiency, and reliability of the overall system for portable applications primarily depend on the converter. Therefore, the selection of an appropriate converter topology is an important and fundamental aspect of designing a fuel cell system for portable applications as the converter alone plays a major role in determining the overall performance of the system. This paper presents a review of power electronics applications in fuel cell systems, which include various topology combinations of DC converters and AC inverters and which are primarily used in fuel cell systems for portable or stand-alone applications. This paper also reviews the switching techniques used in power conditioning for fuel cell systems. Finally, this paper addresses the current problem encountered with DC converters and AC inverter.

  13. Power electronic converter systems for direct drive renewable energy applications

    DEFF Research Database (Denmark)

    Chen, Zhe

    2013-01-01

    This chapter presents power electronic conversion systems for wind and marine energy generation applications, in particular, direct drive generator energy conversion systems. Various topologies are presented and system design optimization and reliability are briefly discussed....

  14. Analysis and Design of a Bidirectional Isolated DC-DC Converter for Fuel Cell and Super-Capacitor Hybrid System

    DEFF Research Database (Denmark)

    Zhang, Zhe; Ouyang, Ziwei; Thomsen, Ole Cornelius

    2012-01-01

    Electrical power system in future uninterruptible power supply (UPS) or electrical vehicle (EV) may employ hybrid energy sources, such as fuel cells and super-capacitors. It will be necessary to efficiently draw the energy from these two sources as well as recharge the energy storage elements...... for zero voltage switching (ZVS). Moreover, a phase-shift and duty cycle modulation method is utilized to control the bidirectional power flow flexibly and it also makes the converter operate under a quasi-optimal condition over a wide input voltage range. This paper describes the operation principle...

  15. Robust symmetrical number system preprocessing for minimizing encoding errors in photonic analog-to-digital converters

    Science.gov (United States)

    Arvizo, Mylene R.; Calusdian, James; Hollinger, Kenneth B.; Pace, Phillip E.

    2011-08-01

    A photonic analog-to-digital converter (ADC) preprocessing architecture based on the robust symmetrical number system (RSNS) is presented. The RSNS preprocessing architecture is a modular scheme in which a modulus number of comparators are used at the output of each Mach-Zehnder modulator channel. The number of comparators with a logic 1 in each channel represents the integer values within each RSNS modulus sequence. When considered together, the integers within each sequence change one at a time at the next code position, resulting in an integer Gray code property. The RSNS ADC has the feature that the maximum nonlinearity is less than a least significant bit (LSB). Although the observed dynamic range (greatest length of combined sequences that contain no ambiguities) of the RSNS ADC is less than the optimum symmetrical number system ADC, the integer Gray code properties make it attractive for error control. A prototype is presented to demonstrate the feasibility of the concept and to show the important RSNS property that the largest nonlinearity is always less than a LSB. Also discussed are practical considerations related to multi-gigahertz implementations.

  16. Design and Simulation of Dc-Dc Converter for Fuel Cell Operated Vehicle with Single Reference Six Pulse Modulation

    Directory of Open Access Journals (Sweden)

    1V.Chaitanya,P.G.scholar,

    2015-10-01

    Full Text Available : Even though electrical vehicle concept is introduced in early 1800’s, it gained importance in past couple of decades due to growing conscience on environmental aspects. Different types of electrical vehicles are manufactured in the past centuries and now onboard generation is seems to be promising by fulfilling the needs of a vehicle. Fuel cells or fuel cell stack produces typically 32-68V of EMF, which has to be conditioned before it fed to motor. The conditioning involves two stages DCDC conversion and then to DC-AC conversion .DC-AC conversion is done through inverter. For DC-DC to conversion various topologies are proposed such as fly back, forward, buck-boost are proposed. This paper deals with the front end DC-DC converter and inverter switching. A hybrid modulation scheme is used to produce pulses to switch the source end full bridge rectifier and inverter at load end. In this modulation scheme high frequency pulses given to full bridge rectifier and 33% modulation scheme based pulses are produced for inverter switching.

  17. Design and implementation of DSP based solar converter for photovoltaic systems

    Energy Technology Data Exchange (ETDEWEB)

    Caliskan, Eser [TUBITAK - MRC, Kocaeli (Turkey). Energy Inst.; Ustun, Ozgur [Istanbul Technical Univ., Maslak (Turkey). Electrical Engineering Dept.

    2012-07-01

    This study discusses the design and implementation of a DSP controlled converter for photovoltaic system that can track the maximum power point, charge and discharge the battery. In the designed system, the boost converter operates the photovoltaic panels at the maximum power point and the bi-directional battery charger charges and discharges the battery bank as demanded. All required switching and control signals for these converters provided by the high performance C2000 series DSP produced by the Texas Instruments. The current, voltage and temperature data are collected by sensors from power stages by using DSP algorithms and the control signals are generated by the embedded software. The load bus is kept at constant voltage by the bi-directional battery charger. The boost converter is controlled by MPPT algorithms and the current sharing or battery charge modes are implemented depending on the radiation value. The designed photovoltaic system performance is verified by simulation and some experiments. (orig.)

  18. Advanced DC-DC converter for power conditioning in hydrogen fuel cell systems

    Energy Technology Data Exchange (ETDEWEB)

    Kovacevic, G.; Tenconi, A.; Bojoi, R. [Department of Electrical Engineering, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino (Italy)

    2008-06-15

    The fuel cell (FC) generators can produce electric energy directly from hydrogen and oxygen. The DC voltage generated by FC is generally low amplitude and it is not constant, depending on the operating conditions. Furthermore, FC systems have dynamic response that is slower than the transient responses typically requested by the load. For this reason, in many applications the FC generators must be interfaced with other energy/power sources by means of an electronic power converter. An advanced full-bridge (FB) DC-DC converter, which effectively achieves zero-voltage switching and zero-current switching (ZVS-ZCS), is proposed for power-conditioning (PC) in hydrogen FC applications. The operation and features of the converter are analyzed and verified by simulations results. The ZVS-ZCS operation is obtained by means of a simple auxiliary circuit. Introduction of the soft-switching operation in PC unit brings improvements not only from the converter efficiency point of view, but also in terms of increased converter power density. Quantitative analysis of hard and soft-switching operating of the proposed converter is also made, bringing in evidence the benefits of soft-switching operation mode. The proposed converter can be a suitable solution for PC in hydrogen FC systems, especially for the medium to high-power applications. (author)

  19. Simulation of Variable Speed Wind Generation System Using Boost Converter of Permanent Magnet Synchronous Generator

    Science.gov (United States)

    Ohyama, Kazuhiro; Sakamoto, Tsuyoshi; Arinaga, Shinji; Yamashita, Yukio

    This paper proposes variable-speed wind generation system using the boost converter. The proposed system has three speed control modes for the wind velocity. The control mode of low wind velocity regulates the armature current of the generator with the boost converter to control the speed of wind turbine. The control mode of middle wind velocity regulates the DC link voltage with the vector controlled inverter to control the speed of wind turbine. The control mode of high wind velocity regulates the pitch angle of the wind turbine with the pitch angle control system to control the speed of wind turbine. The hybrid of three control modes extends the variable-speed range. The proposed system simplifies the maintenance and improves the reliability and reduces the cost in compare with the variable-speed wind generation system using PWM converter. This paper describes the control strategy and modeling for simulation using Matlab Simulink of the proposed system. Also this paper describes the control strategy and modeling of variable-speed wind generation system using PWM converter. The steady state and transient responses for wind velocity changes are simulated using the Matlab Simulink. This paper verifies the fundamental performance of the system using boost converter by discussing the simulation results of the both systems.

  20. Voltage-Balancing Method for Modular Multilevel Converters Under Phase-Shifted Carrier-Based Pulsewidth Modulation

    DEFF Research Database (Denmark)

    Deng, Fujin; Chen, Zhe

    2015-01-01

    The modular multilevel converter (MMC) becomes attractive for medium- or high-power applications because of the advantages of high modularity, availability, and power quality. One of the technical challenges associated with an MMC is the balancing of the capacitors' voltages. In this paper......, a voltage-balancing control method is proposed for the MMC under phase-shifted carrier-based pulsewidth modulation. The proposed voltage-balancing method uses the linearization method for pulse sorting without arm current measurement, which can control the capacitor charge transfer to balance the capacitor....../EMTDC are conducted, and a downscale MMC prototype is also tested with the proposed method. The study results show the effectiveness of the proposed voltage-balancing method....

  1. Modeling, Dynamics, Bifurcation Behavior and Stability Analysis of a DC-DC Boost Converter in Photovoltaic Systems

    Science.gov (United States)

    Zhioua, M.; El Aroudi, A.; Belghith, S.; Bosque-Moncusí, J. M.; Giral, R.; Al Hosani, K.; Al-Numay, M.

    A study of a DC-DC boost converter fed by a photovoltaic (PV) generator and supplying a constant voltage load is presented. The input port of the converter is controlled using fixed frequency pulse width modulation (PWM) based on the loss-free resistor (LFR) concept whose parameter is selected with the aim to force the PV generator to work at its maximum power point. Under this control strategy, it is shown that the system can exhibit complex nonlinear behaviors for certain ranges of parameter values. First, using the nonlinear models of the converter and the PV source, the dynamics of the system are explored in terms of some of its parameters such as the proportional gain of the controller and the output DC bus voltage. To present a comprehensive approach to the overall system behavior under parameter changes, a series of bifurcation diagrams are computed from the circuit-level switched model and from a simplified model both implemented in PSIM© software showing a remarkable agreement. These diagrams show that the first instability that takes place in the system period-1 orbit when a primary parameter is varied is a smooth period-doubling bifurcation and that the nonlinearity of the PV generator is irrelevant for predicting this phenomenon. Different bifurcation scenarios can take place for the resulting period-2 subharmonic regime depending on a secondary bifurcation parameter. The boundary between the desired period-1 orbit and subharmonic oscillation resulting from period-doubling in the parameter space is obtained by calculating the eigenvalues of the monodromy matrix of the simplified model. The results from this model have been validated with time-domain numerical simulation using the circuit-level switched model and also experimentally from a laboratory prototype. This study can help in selecting the parameter values of the circuit in order to delimit the region of period-1 operation of the converter which is of practical interest in PV systems.

  2. An improved thermal network model of the IGBT module for wind power converters considering the effects of base plate solder fatigue

    Science.gov (United States)

    Li, H.; Hu, Y. G.; Liu, S. Q.; Li, Y.; Liao, X. L.; Liu, Z. X.

    2016-08-01

    This study presents an improved thermal network model of the IGBT module that considers the effects of base plate solder fatigue on the junction temperature of the said module used in wind power converters. First, the coupling thermal structure 3D finite element model of the IGBT module is established based on the structure and material parameters of the module used in the wind power converters of a doubly fed induction generator. The junction temperature of the module is also investigated at different thermal desquamating degrees of the base plate solder. Second, the thermal resistance parameters are determined at different desquamating degrees, and the improved thermal network model that considers the effects of base plate solder fatigue is established. Finally, the two results of the calculation of the junction temperature are compared in different fatigue stages through the improved thermal network model and the 3D finite element model, which testify to the effectiveness of the improved thermal network model.

  3. Virtual-vector-based space vector pulse width modulation of the DC-AC multilevel-clamped multilevel converter (MLC2)

    DEFF Research Database (Denmark)

    Rodriguez, Pedro; Busquets-Monge, Sergio; Blaabjerg, Frede

    2011-01-01

    This work presents the development of the space vector pulse width modulation (SVPWM) of a new multi-level converter topology. First, the proposed converter and its natural space vector diagram are presented. Secondly, a modified space vector diagram based on the virtual-vectors technique is shown....... Simulation results by using a space vector approach are presented. Special emphasis is given on the total harmonic distortion (THD) by making a comparison with those of the classical NPC topologies....

  4. Pressure intelligent control strategy of Waste heat recovery system of converter vapors

    Science.gov (United States)

    Feng, Xugang; Wu, Zhiwei; Zhang, Jiayan; Qian, Hong

    2013-01-01

    The converter gas evaporative cooling system is mainly used for absorbing heat in the high temperature exhaust gas which produced by the oxygen blowing reaction. Vaporization cooling steam pressure control system of converter is a nonlinear, time-varying, lagging behind, close coupling of multivariable control object. This article based on the analysis of converter operation characteristics of evaporation cooling system, of vaporization in a production run of pipe pressure variation and disturbance factors.For the dynamic characteristics of the controlled objects,we have improved the conventional PID control scheme.In Oxygen blowing process, we make intelligent control by using fuzzy-PID cascade control method and adjusting the Lance,that it can realize the optimization of the boiler steam pressure control.By design simulation, results show that the design has a good control not only ensures drum steam pressure in the context of security, enabling efficient conversion of waste heat.And the converter of 1800 flue gas through pipes and cool and dust removal also can be cooled to about 800. Therefore the converter haze evaporative cooling system has achieved to the converter haze temperature decrease effect and enhanced to the coal gas returns-ratio.

  5. Evaluation and Design Tools for the Reliability of Wind Power Converter System

    DEFF Research Database (Denmark)

    Ma, Ke; Zhou, Dao; Blaabjerg, Frede

    2015-01-01

    of suitable physic-of-failure based evaluation tools for a reliability assessment in power electronics. In this paper, an advanced tool structure which can acquire various reliability metrics of wind power converter is proposed. The tool is based on failure mechanisms in critical components of the system......As a key part in the wind turbine system, the power electronic converter is proven to have high failure rates. At the same time, the failure of the wind power converter is becoming more unacceptable because of the quick growth in capacity, remote locations to reach, and strong impact to the power...... grid. As a result, the correct assessment of reliable performance for power electronics is a crucial and emerging need; the assessment is essential for design improvement, as well as for the extension of converter lifetime and reduction of energy cost. Unfortunately, there still exists a lack...

  6. Configuration of Distributed Message Converter Systems using Performance Modeling

    NARCIS (Netherlands)

    Aberer, Karl; Risse, Thomas; Wombacher, Andreas

    2001-01-01

    To find a configuration of a distributed system satisfying performance goals is a complex search problem that involves many design parameters, like hardware selection, job distribution and process configuration. Performance models are a powerful tools to analyse potential system configurations, howe

  7. Incremental Conductance MPPT Algorithm for PV System Implemented Using DC-DC Buck and Boost Converter

    OpenAIRE

    2014-01-01

    The two basic topologies of switch mode DC-DC converters (Buck and Boost) are analyzed with a view of their use in PV (photovoltaic) systems, as the photovoltaic generator exhibits non-linear characteristics due to the change in environmental condition and load variation. As the efficiency of PV panels is low it becomes mandatory to extract maximum power from the PV panel at a given period of time. Several MPPT algorithms with different types of converters are being proposed f...

  8. Boost converter with combined control loop for a stand-alone photovoltaic battery charge system

    OpenAIRE

    Mira Albert, Maria del Carmen; Knott, Arnold; Thomsen, Ole Cornelius; Andersen, Michael A. E.

    2013-01-01

    The converter control scheme plays an important role in the performance of maximum power point tracking (MPPT) algorithms. In this paper, an input voltage control with double loop for a stand-alone photovoltaic system is designed and tested. The inner current control loop with high crossover frequency avoids perturbations in the load being propagated to the photovoltaic panel and thus deviating the operating point. Linearization of the photovoltaic panel and converter state-space modeling is ...

  9. Phase-Modulated Nonresonant Laser Pulses Can Selectively Convert Enantiomers in a Racemic Mixture

    DEFF Research Database (Denmark)

    Thomas, Esben Folger; Henriksen, Niels Engholm

    2017-01-01

    Deracemization occurs when a racemic molecular mixture is transformed into a mixture containing an excess of a single enantiomer. Recent advances in ultrafast laser technology hint at the possibility of using shaped pulses to generate deracemization via selective enantiomeric conversion; however......-modulated, nonresonant, linearly polarized Gaussian laser pulses that can selectively deracemize a racemic mixture of 3D-oriented, 3,5-difluoro-3',5'-dibromobiphenyl (F2H3C6-C6H3Br2) molecules, the laser-induced dynamics of which are well studied experimentally. These results strongly suggest that designing a closed......-loop coherent control scheme based on this methodology may lead to the first-ever achievement of enantiomeric conversion via coherent laser light in a laboratory setting....

  10. A Multi-Functional Power Electronic Converter in Distributed Generation Power Systems

    DEFF Research Database (Denmark)

    Chen, Zhe; Blaabjerg, Frede; Pedersen, John Kim

    2005-01-01

    of the converter interfacing a wind power generation unit is also given. The power electronic interface performs the optimal operation in the wind turbine system to extract the maximum wind power, while it also plays a key role in a hybrid compensation system that consists of the active power electronic converter...... and passive filters connected to each distorting load or distributed generation (DG) unit. The passive filters are distributely located to remove major harmonics and provide reactive power compensation. The active power electronic filter corrects the system unbalance, removes the remaining harmonic components......, and damps the possible harmonic resonance. Simulation results demonstrate that the converter system can transfer the real power by following a desired reference power for a variable speed wind power conversion system to effectively extract the renewable energy and also enhance the power quality...

  11. Nonlinear control of voltage source converters in AC-DC power system.

    Science.gov (United States)

    Dash, P K; Nayak, N

    2014-07-01

    This paper presents the design of a robust nonlinear controller for a parallel AC-DC power system using a Lyapunov function-based sliding mode control (LYPSMC) strategy. The inputs for the proposed control scheme are the DC voltage and reactive power errors at the converter station and the active and reactive power errors at the inverter station of the voltage-source converter-based high voltage direct current transmission (VSC-HVDC) link. The stability and robust tracking of the system parameters are ensured by applying the Lyapunov direct method. Also the gains of the sliding mode control (SMC) are made adaptive using the stability conditions of the Lyapunov function. The proposed control strategy offers invariant stability to a class of systems having modeling uncertainties due to parameter changes and exogenous inputs. Comprehensive computer simulations are carried out to verify the proposed control scheme under several system disturbances like changes in short-circuit ratio, converter parametric changes, and faults on the converter and inverter buses for single generating system connected to the power grid in a single machine infinite-bus AC-DC network and also for a 3-machine two-area power system. Furthermore, a second order super twisting sliding mode control scheme has been presented in this paper that provides a higher degree of nonlinearity than the LYPSMC and damps faster the converter and inverter voltage and power oscillations.

  12. Simulation of High Step-Up DC–DC Converter for Photovoltaic Module Application using MATLAB/SIMULINK

    Directory of Open Access Journals (Sweden)

    S.Daison Stallon

    2013-06-01

    Full Text Available As per the present scenario lot of power shortages are there in all over the world especially country like India the grid transferring problem is also high. Almost the power from the fossil fuels are becoming so less some of the examples of the fossil fuels are (coal, lignite, oil, and gases.So most of them looking in forward for the power from green or renewable based energies like solar, wind, biomass, tidal etc. Which does not cause any pollution to the environment. In this paper the simulation and analysis of the PV panel and also high efficient boost converter design and simulation is also performed. Even though the solar based systems are renewable based energies when compared to other renewable energies like wind, biomass it does not connect to more number of grid connections. Lot of necessary steps want to be taken one of the main important factor that high efficient boost converter is needed, here in this paper the input voltage to the boost converter is given as 15V and receives the output voltage of 55.64V

  13. Power Converters and Control of Renewable Energy Systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Teodorescu, Remus; Chen, Zhe;

    2004-01-01

    The global electrical energy consumption is steadily rising and therefore a continuous demand to increase the power generation capacity. A significant percentage of the required capacity increase can be based on renewable energy sources. Wind turbine technology, as the most cost effective renewable...... energy conversion system, will play an important part in our future energy supply. But other sources like microturbines, photovoltaics and fuel cell systems may also be serious contributor to the power supply. Characteristically, power electronics will be an efficient and important interface to the grid...... for the renewables and this paper will first briefly discuss three different alternative/renewable energy sources. Next, various configurations of small and medium power conversion topologies are presented including their control (mainly for PV-systems). Finally wind turbine configuration and their control...

  14. Incremental Conductance MPPT Algorithm for PV System Implemented Using DC-DC Buck and Boost Converter

    Directory of Open Access Journals (Sweden)

    Dhananjay Choudhary

    2014-08-01

    Full Text Available The two basic topologies of switch mode DC-DC converters (Buck and Boost are analyzed with a view of their use in PV (photovoltaic systems, as the photovoltaic generator exhibits non-linear characteristics due to the change in environmental condition and load variation. As the efficiency of PV panels is low it becomes mandatory to extract maximum power from the PV panel at a given period of time. Several MPPT algorithms with different types of converters are being proposed for extracting maximum power from the PV panel. It is found that the nature of load plays an important role in the choice of topology. This paper investigates the implementation issues of Incremental Conductance method with Buck and Boost Converters. Mathematical analysis and desirable steady-state operating point of the converters are derived to give satisfactory maximum power point tracking operation.

  15. Direct switching control of DC-DC power electronic converters using hybrid system theory

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, J.; Lin, F. [Wayne State Univ., Detroit, MI (United States). Dept. of Electrical and Computer Engineering; Wang, C. [Wayne State Univ., Detroit, MI (United States). Dept. of Electrical and Computer Engineering; Wayne State Univ., Detroit, MI (United States). Div. of Engineering Technology

    2010-07-01

    A direct switching control (DSC) scheme for power electronics converters was described. The system was designed for use in both traditional and renewable energy applications as well as in electric drive vehicles. The proposed control scheme was based on a detailed hybrid system converter model that used model predictive control (MPC), piecewise affine (PWA) approximations and constrained optimal control methods. A DC-DC converter was modelled as a hybrid machine. Switching among different modes of the DC-DC converter were modelled as discrete events controlled by the hybrid controller. The modelling scheme was applied to a Buck converter. The DSC was used to control the switch of the power converter based on a hybrid machine model. Results of the study showed that the method can be used to regulate output voltage and inductor currents. The method also provides fast transient responses and effectively regulates both currents and voltage. The controller can be used to provide immediate responses to dynamic disturbances and output voltage fluctuations. 23 refs., 7 figs.

  16. A New Sliding Mode Controller for DC/DC Converters in Photovoltaic Systems

    Directory of Open Access Journals (Sweden)

    M. Sarvi

    2013-01-01

    Full Text Available DC/DC converters are widely used in many industrial and electrical systems. As DC/DC converters are nonlinear and time-variant systems, the application of linear control techniques for the control of these converters is not suitable. In this paper, a new sliding mode controller is proposed as the indirect control method and compared to a simple direct control method in order to control a buck converter in photovoltaic applications. The solar arrays are dependent power sources with nonlinear voltage-current characteristics under different environmental conditions (insolation and temperature. From this point of view, the DC/DC converter is particularly suitable for the application of the sliding mode control in photovoltaic application, because of its controllable states. Simulations are performed in Matlab/Simulink software. The simulation results are presented for a step change in reference voltage and input voltage as well as step load variations. The simulations results of proposed method are compared with the conventional PID controller. The results show the good performance of the proposed sliding mode controller. The proposed method can be used for the other DC/DC converter.

  17. A novel synthetic test system for thyristor level in the converter valve of HVDC power transmission

    Directory of Open Access Journals (Sweden)

    Liu Longchen

    2016-01-01

    Full Text Available The converter valve is the core equipment in the HVDC power transmission system, a+-nd its performance has a direct effect on the reliability, stability and efficiency of the whole power system. As the basic unit of HVDC converter valve, the thyristor level needs to be test routinely in order to grasp the state of the converter valve equipment. Therefore, it is urgent to develop a novel synthetic test system for the thyristor level with thyristor control unit (TCU. However, currently there is no specific test scheme for the thyristor level of HVDC converter valve. In this paper, the synthetic test principle, content and methods for the thyristor level with TCU are presented based on the analysis of the thyristor reverse recovery characteristic and the IEC technology standard. And a transient high-voltage pulse is applied to the thyristor level during its reverse recovery period in order to test the characteristics of thyristor level. Then, the synthetic test system for the thyristor level is applied to the converter valve test of ±800 kV HVDC power transmission project, and the practical test result verifies the reasonability and validity of the proposed synthetic test system.

  18. A Converter from the Systems Biology Markup Language to the Synthetic Biology Open Language.

    Science.gov (United States)

    Nguyen, Tramy; Roehner, Nicholas; Zundel, Zach; Myers, Chris J

    2016-06-17

    Standards are important to synthetic biology because they enable exchange and reproducibility of genetic designs. This paper describes a procedure for converting between two standards: the Systems Biology Markup Language (SBML) and the Synthetic Biology Open Language (SBOL). SBML is a standard for behavioral models of biological systems at the molecular level. SBOL describes structural and basic qualitative behavioral aspects of a biological design. Converting SBML to SBOL enables a consistent connection between behavioral and structural information for a biological design. The conversion process described in this paper leverages Systems Biology Ontology (SBO) annotations to enable inference of a designs qualitative function.

  19. Operational Principle and Tuning of the MegaDiscaP Power Converters Control System

    CERN Document Server

    Cravero, JM; Garcia Retegui, R; Benedetti, M; Maestri, S; Kloster, W

    2010-01-01

    This technical report presents the regulation system of the MegaDiscaP power converter prototype. This type of converter will be used to power the septum magnet for Booster injection with Linac 4. First, the MegaDiscaP topology and operational principles are introduced. Then, as the system is composed by different stages, a regulation system capable of handling their interconnections with minimum transient response is presented. Its features, behavior and design considerations adopted are accounted for. Finally, a complete documentation of the implemented software is reported.

  20. Point-of-load switched-capacitor DC-DC converter for distributed power systems

    Science.gov (United States)

    Shunkov, V. E.; Kus, O. N.; Prokopyev, V. Y.; Butuzov, V. A.; Bocharov, Y. I.; Shunkov, V. E.

    2016-10-01

    Integrated circuit (IC) of point-of-load DC-DC converter is presented. It is intended mainly for use in distributed power systems as a stand-along IC or as an on-chip block of the system-on-chip. The converter is based on multiphase switched-capacitor architecture and implemented in commercially available, 180 nm bulk-CMOS process. The paper discusses features of output voltage control in the multiphase system over a wide range of input and output voltages and load currents as well as output noise reducing techniques. The results of the test samples evaluation are presented.

  1. Simulation of wind power with front-end converter into interconnected grid system

    Directory of Open Access Journals (Sweden)

    Sharad W. Mohod

    2009-09-01

    Full Text Available In the growing electricity supply industry and open access market for electricity worldwide, renewable sources are getting added into the grid system. This affects the grid power quality. To assess the impact on grid due to wind energy integration, the knowledge of electrical characteristic of wind turbine and associated control equipments are required. The paper presents a simulation set-up for wind turbine in MATLAB / SIMULINK, with front end converter and interconnected system. The presented control scheme provides the wind power flow to the grid through a converter. The injected power in the system at the point of common coupling is ensured within the power quality norms.

  2. Criteria for the evaluation of laser solar energy converter systems

    Science.gov (United States)

    Harries, W. L.

    1985-01-01

    Assuming that a parabolic insolation-collection mirror-based solar pumped laser has a collector and heat emitter whose weights are proportional to their areas, and that the weight of the laser is negligible by comparison, the output power/unit weight can be expressed in terms of the efficiencies and working temperatures of the system. This ratio appears to be several times higher for an IBr laser than for one operating on C3F7I, because the solar utilization efficiency is greater for the former despite its lower working temperature.

  3. CONTROL SYSTEM IDENTIFICATION THROUGH MODEL MODULATION METHODS

    Science.gov (United States)

    identification has been achieved by using model modulation techniques to drive dynamic models into correspondence with operating control systems. The system ... identification then proceeded from examination of the model and the adaptive loop. The model modulation techniques applied to adaptive control

  4. Converting signals to knowledge in structural health monitoring systems

    Science.gov (United States)

    Brownjohn, James M. W.; Moyo, Pilate; Omenzetter, Piotr; Chakraboorty, Sushanta

    2005-04-01

    Academic approaches in structural health monitoring (SHM) usually focus on fine detail or on aspects of the technology such as sensors and data collection, and areas that may be less useful to operators than information about the level of performance of their structures. The steps in the process of SHM such as data management, data mining, conversion to knowledge of structural behaviour and integrity are frequently absent, and even the most operationally successful SHM systems may lack the component where deep understanding on the nature of the structure performance is obtained. This paper presents experience gained in a number of SHM exercises where static and dynamic response data have been interpreted, with or without the aid of calibrated structural models, in order to characterise the mechanisms at work and the experiences of the structure.

  5. Hierarchical Velocity Control Based on Differential Flatness for a DC/DC Buck Converter-DC Motor System

    Directory of Open Access Journals (Sweden)

    R. Silva-Ortigoza

    2014-01-01

    Full Text Available This paper presents a hierarchical controller that carries out the angular velocity trajectory tracking task for a DC motor driven by a DC/DC Buck converter. The high level control is related to the DC motor and the low level control is dedicated to the DC/DC Buck converter; both controls are designed via differential flatness. The high level control provides a desired voltage profile for the DC motor to achieve the tracking of a desired angular velocity trajectory. Then, a low level control is designed to ensure that the output voltage of the DC/DC Buck converter tracks the voltage profile imposed by the high level control. In order to experimentally verify the hierarchical controller performance, a DS1104 electronic board from dSPACE and Matlab-Simulink are used. The switched implementation of the hierarchical average controller is accomplished by means of pulse width modulation. Experimental results of the hierarchical controller for the velocity trajectory tracking task show good performance and robustness against the uncertainties associated with different system parameters.

  6. Analysis, Design, Modeling, and Control of an Interleaved-Boost Full-Bridge Three-Port Converter for Hybrid Renewable Energy Systems

    DEFF Research Database (Denmark)

    Mira Albert, Maria del Carmen; Zhang, Zhe; Knott, Arnold

    2017-01-01

    This paper presents the design, modeling, and control of an isolated dc-dc three-port converter (TPC) based on an interleaved-boost full-bridge converter with pulsewidth modulation (PWM) and phase-shift control for hybrid renewable energy systems. In the proposed topology, the switches are driven......, a prototype is constructed and tested under the various modes, depending on the availability of the renewable energy source and the load consumption. The experimental results show that the two decoupled control variables achieve effective regulation of the power flow among the three ports....

  7. Final design of the Korean AC/DC converters for the ITER coil power supply system

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Jong-Seok, E-mail: jsoh@nfri.re.kr [ITER Korea, National Fusion Research Institute, Daejeon 305-806 (Korea, Republic of); Choi, Jungwan; Suh, Jae-Hak; Choi, Jihyun [ITER Korea, National Fusion Research Institute, Daejeon 305-806 (Korea, Republic of); Lee, Lacksang; Kim, Changwoo; Park, Hyungjin; Jo, Seongman; Lee, Seungyun; Hwang, Kwangcheol; Liu, Hyoyol [Dawonsys Corp., Siheung 429-450 (Korea, Republic of); Hong, Ki-Don; Sim, Dong-Joon; Lee, Jang-Soo [Hyosung Corp., Gongdeok-Dong, Seoul 121-720 (Korea, Republic of); Lee, Eui-Jae; Kwon, Yang-Hae; Lee, Dae-Yeol; Ko, Ki-Won; Kim, Jong-Min [Mobiis Corp., Yangjae-dong, Seoul 137-888 (Korea, Republic of); Song, Inho [ITER Organization, Route de Vinon sur Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); and others

    2015-10-15

    The final design of the ITER TF, CS, CC and VS AC/DC converters has been completed to implement ITER requirements following the detailed design and refinements of the preliminary design. The number of parallel thyristors and the rating of fuses are coordinated to keep those devices within the explosion limit even under most severe fault conditions. The impedance of the converter transformer has been optimized taking into account the energization inrush current, short circuit current, reactive power consumption and the available DC voltage. To ensure system integrity, AC/DC converters are mechanically divided into transformers, AC busbars, 6-pulse bridges, DC interconnecting busbars and DC reactors, and then all subsystems are decoupled by flexible links. To provide stable real time network communication down to the converters, a one GbE link is deployed between master controllers and local controllers. IEEE 1588 is implemented to the embedded controllers for precision time synchronization. This paper describes the detailed solutions implemented in the final design for the ITER AC/DC converters with R&D results of converter prototypes.

  8. An out-of-core thermionic-converter system for nuclear space power.

    Science.gov (United States)

    Breitwieser, R.

    1972-01-01

    Reexamination of designs of nuclear thermionic space power systems with the converter outside the reactor in the perspective of recent advances in heat-transfer methods, materials, converter performance, and radiation design. The 40- to 70-kW(e) power range is treated. The configuration is found to meet the constraints of readily available launch vehicles. It allows for off-design operation including startup, shutdown, and possible emergency conditions; provides tolerance of failure by extensive use of modular, redundant elements; incorporates and uses heat pipes in a fashion that reduces the need for extensive in-pile testing of system components; and uses thermionic converters, nuclear fuel elements, and heat-transfer devices in a geometrical form adapted from existing incore thermionic system designs.

  9. Effects of nitrosopropofol on mitochondrial energy-converting system.

    Science.gov (United States)

    Stevanato, Roberto; Momo, Federico; Marian, Michela; Rigobello, Maria Pia; Bindoli, Alberto; Bragadin, Marcantonio; Vincenti, Ezio; Scutari, Guido

    2002-10-01

    Nitrosopropofol (NOPR) is a relatively stable compound obtained from the reaction between the general anesthetic 2,6 diisopropylphenol (propofol) and nitrosoglutathione (GSNO) and bearing a more acidic phenol group than propofol. It interfered with mitochondrial energetic metabolism in a concentration-dependent manner. Concentrations as high as 100 or 200 microM disrupted both oxidative phosphorylation and electron transport. Low concentrations of NOPR (50 microM) markedly slowed down the electron transport rate which was insensitive both to ADP and uncoupler stimulation and spontaneously gradually stopped. Consequently, both the transmembrane potential production and the ATP synthesis system were affected. In the presence of 10 or 20 microM NOPR, mitochondria respired but showed a worsening of the respiratory control and produced a transmembrane potential useful to respond to a phosphorylation pulse, but were not able to restore it. These results were consistent with ATP synthesis and swelling experiments. NOPR was effective at concentrations lower than those required by the combination of propofol and GSNO, suggesting that mitochondria might be able to catalyze the reaction between GSNO and propofol and that the resulting metabolite was more active on mitochondrial membrane structure than the parent compounds. Although the details of the process are yet unknown, the mechanism presented may be of potential relevance to rationalize the pathophysiological effects of propofol.

  10. DC-link Voltage Coordinative-Proportional Control in Cascaded Converter Systems

    DEFF Research Database (Denmark)

    Tian, Yanjun; Loh, Poh Chiang; Deng, Fujin

    2015-01-01

    PI controllers are frequently implemented in cascaded converter system to control the DC-link voltage, because they can achieve zero steady state error. However the PI controller adds a pole at the origin point and a zero on the left half plane, and it increases the control system type number, an...

  11. Validation of a Tool for the Initial Dynamic Design of Mooring Systems for Large Floating Wave Energy Converters

    DEFF Research Database (Denmark)

    Thomsen, Jonas Bjerg; Ferri, Francesco; Kofoed, Jens Peter

    2017-01-01

    Mooring of floating wave energy converters is an important topic in renewable research since it highly influences the overall cost of the wave energy converter and thereby the cost of energy. In addition, several wave energy converter failures have been observed due to insufficient mooring system...

  12. Modulation characteristics of a DFB-laser with integrated spot-size converter for efficient laser fiber coupling

    Energy Technology Data Exchange (ETDEWEB)

    Zengerle, R.; Greus, C.; Burkhard, H.; Ries, R.; Janning, H.; Kuphal, E. [Deutsche Telekom AG, Technologiezentrum, Darmstadt (Germany); Huebner, B. [Univ. Wuerzburg (Germany). Technische Physik

    1996-12-31

    The RF-modulation emission characteristics of a MQW DFB laser monolithically integrated with a laterally tapered spot-size transformer on InGaAsP/InP were investigated and key results were presented. Despite the relatively simple design of the devices they are characterized by good high speed lasing properties with a direct modulation response exceeding 5 GHz. A simple low loss chip-fiber coupling arrangement with large optical alignment tolerances was demonstrated and is regarded as a particular advantage of these devices. Their experiments confirm the attractivity of this integration concept for low cost laser components in optical transmission systems.

  13. Local Convertibility and the Quantum Simulation of Edge States in Many-Body Systems

    Directory of Open Access Journals (Sweden)

    Fabio Franchini

    2014-11-01

    Full Text Available In some many-body systems, certain ground-state entanglement (Rényi entropies increase even as the correlation length decreases. This entanglement nonmonotonicity is a potential indicator of nonclassicality. In this work, we demonstrate that such a phenomenon, known as lack of local convertibility, is due to the edge-state (deconstruction occurring in the system. To this end, we employ the example of the Ising chain, displaying an order-disorder quantum phase transition. Employing both analytical and numerical methods, we compute entanglement entropies for various system bipartitions (A|B and consider ground states with and without Majorana edge states. We find that the thermal ground states, enjoying the Hamiltonian symmetries, show lack of local convertibility if either A or B is smaller than, or of the order of, the correlation length. In contrast, the ordered (symmetry-breaking ground state is always locally convertible. The edge-state behavior explains all these results and could disclose a paradigm to understand local convertibility in other quantum phases of matter. The connection we establish between convertibility and nonlocal, quantum correlations provides a clear criterion of which features a universal quantum simulator should possess to outperform a classical machine.

  14. A DC-DC Converter Efficiency Model for System Level Analysis in Ultra Low Power Applications

    Directory of Open Access Journals (Sweden)

    Benton H. Calhoun

    2013-06-01

    Full Text Available This paper presents a model of inductor based DC-DC converters that can be used to study the impact of power management techniques such as dynamic voltage and frequency scaling (DVFS. System level power models of low power systems on chip (SoCs and power management strategies cannot be correctly established without accounting for the associated overhead related to the DC-DC converters that provide regulated power to the system. The proposed model accurately predicts the efficiency of inductor based DC-DC converters with varying topologies and control schemes across a range of output voltage and current loads. It also accounts for the energy and timing overhead associated with the change in the operating condition of the regulator. Since modern SoCs employ power management techniques that vary the voltage and current loads seen by the converter, accurate modeling of the impact on the converter efficiency becomes critical. We use this model to compute the overall cost of two power distribution strategies for a SoC with multiple voltage islands. The proposed model helps us to obtain the energy benefits of a power management technique and can also be used as a basis for comparison between power management techniques or as a tool for design space exploration early in a SoC design cycle.

  15. Fault Diagnosis and Fault-tolerant Control of Modular Multi-level Converter High-voltage DC System: A Review

    DEFF Research Database (Denmark)

    Liu, Hui; Ma, Ke; Wang, Chao;

    2016-01-01

    Modular Multilevel Converter based High Voltage Direct Current (MMC-HVDC) configuration is a promising solution for the efficient grid integration and bulky power transmission over long distance. However, the large number of series connected identical modules in MMC may increase the probability...... strategies of MMC-HVDC systems for the most common faults happened in MMC-HVDC systems covering MMC faults, DC side faults as well as AC side faults. An important part of this paper is devoted to a discussion of the vulnerable spots as well as failure mechanism of the MMC-HVDC system covering switching...... device fault, DC line faults as well as AC grid faults. Special attention is given to the comparison of the corresponding fault diagnosis and fault-tolerant control approaches. Further, focus is dedicated to control/protection strategies and topologies with fault ride-though capability for MMC...

  16. Discrete Displacement Hydraulic Power Take-Off System for the Wavestar Wave Energy Converter

    DEFF Research Database (Denmark)

    Hansen, Rico Hjerm; Kramer, Morten; Vidal, Enrique

    2013-01-01

    The Wavestar Wave Energy Converter (WEC) is a multiple absorber concept, consisting of 20 hemisphere shaped floats attached to a single platform. The heart of the Wavestar WEC is the Power Take-Off (PTO) system, converting the wave induced motion of the floats into a steady power output to the grid....... In the present work, a PTO based on a novel discrete displacement fluid power technology is explored for the Wavestar WEC. Absorption of power from the floats is performed by hydraulic cylinders, supplying power to a common fixed pressure system with accumulators for energy smoothing. The stored pressure energy...

  17. 4 Gb/s two-level to 2 symbol/s four-level converter GaAs IC for semiconductor optical amplifier modulators

    DEFF Research Database (Denmark)

    Riishøj, J.; Nielsen, Torben Nørskov; Gliese, Ulrik Bo

    1993-01-01

    A design of a 50 Ω impedance matched two-to-four level converter GaAs IC for two-electrode semiconductor optical amplifier modulators is presented. Eye diagrams with good eye openings and 0.33 V spacing between adjacent logic levels are demonstrated for input bit rates up to 4 Gb/s. A novel...

  18. Simulación de Convertidores de Potencia en Sistemas Eólicos Simulation of Power Converters for Wind Energy Systems

    Directory of Open Access Journals (Sweden)

    Rui Melício

    2007-01-01

    Full Text Available En el presente trabajo se hace un análisis actual de la capacidad instalada de producción de energía eléctrica utilizando fuentes de energía renovable en Portugal y se analiza la situación actual relacionada con convertidores electrónicos de potencia. Además el trabajo aporta información sobre la simulación de topologías de convertidores de potencia en los sistemas de energía eólica, los convertidores usuales de dos niveles, el convertidor multinivel y el convertidor matricial. Se usa el método de la modulación de los pulsos de disparo mediante vectores espaciales de tensión y el control por modo de deslizamiento. Esta simulación permite concluir que las ondas de tensión y corriente en los convertidores de dos etapas AC/DC/AC se presentan con mejor comportamiento armónico que en el convertidor de una etapa AC/AC.This paper presents an analysis of the present installed electric power capacity of renewable energy power systems in Portugal, and analyzes the present state of power converters applied to wind farms. Also, this paper presents a simulation of a wind energy system with the usual topology for power converters, a two-levels converter, a multi-level converter and a matrix converter, using pulse modulation by space vector modulation. The simulation allows concluding that the waves for the electric voltage and the current in the converters AC/DC/AC have better performance than in the matrix converter AC/AC.

  19. Advanced Control Strategy of Back-to-Back PWM Converters in PMSG Wind Power System

    Directory of Open Access Journals (Sweden)

    Tan Luong Van

    2015-01-01

    Full Text Available This paper proposes a control scheme of back-to-back PWM converters for the permanent magnet synchronous generator (PMSG wind turbine system. The DC-link voltage can be controlled at the machine-side converter (MSC, while the grid-side converter (GSC controls the grid active power for a maximum power point tracking (MPPT. At the grid fault condition, the DC-link voltage controller is designed using a feedback linearization (FL theory. For the MPPT, a proportional control loop is added to the torque control to reduce the influence of the inertia moment in the wind turbines, which can improve its dynamic performance. The validity of this control algorithm has been verified by the simulation of the 2-MW PMSG wind turbine system.

  20. Current Source Converter Based Multi-terminal DC Wind Energy Conversion System

    Institute of Scientific and Technical Information of China (English)

    Shixiong FAN; Guangyi LIU; Zhanyong YANG; Weiwei MA; Barry W.WILLIAMS

    2013-01-01

    A current source converter based multi-terminal direct current (DC) wind energy conversion system (WECS) is proposed.The current source DC/DC converter is adopted to connect a wind turbine to an inverter with maximum power point control.Each turbine is associated with a DC source by parallel-connected to a common DC link.After DC power collection,a current source inverter (CSI) using gate turn-off components is used for the grid connection due to its flexible reactive power control and short circuit protection capabilities.For such a parallel connection configuration,the CSI operates in an input voltage control mode,which maintains the DC link voltage constant.The dynamic responses of combined mechanical and electrical systems are investigated with three different operation cases.Simulation and experimental results demonstrate the feasibility and stability of the current source DC/DC converter based multi-terminal DC WECS.

  1. Thermal Analysis of Multi-MW Two-Level Generator Side Converters with Reduced Common-Mode-Voltage Modulation Methods for Wind Turbines

    DEFF Research Database (Denmark)

    Qin, Zian; Liserre, Marco; Blaabjerg, Frede

    2013-01-01

    Thermal performance is one of the main indicators of power converter, since it is related to both the cost of cooling system and the reliability of the power converter. Moreover, the common-mode voltage in motor driver may damage the bearing of the motor and also cause failure. Therefore, both...

  2. Design on a Ka-band Up-converter Module%Ka频段上变频模块设计

    Institute of Scientific and Technical Information of China (English)

    陈焕东

    2011-01-01

    A new Ka-band Up-converter module is described in this paper.How to achieve low spurious and low phase noise performance is studied,and then the feasible scheme is designed.The filter is co-simulated by Ansoft Designer and HFSS software and is realized with thin film technique.High spurious suppression is obtained by the filter.A 27 GHz local oscillator with very low phase noise is realized by sampling phase-locked technique.The waveguide to micro-strip transition is simulated.Finally the module is tested,and the design objective is satisfied.%论述一种Ka频段上变频模块设计,对模块的杂散和相位噪声性能做了分析,根据分析结果,设计出合理的变频方案。滤波器采用Ansoft Designer和HFSS软件协同仿真,薄膜工艺制作,获得足够的杂散抑制度从而实现低杂散。应用取样锁相技术合成了相位噪声极低的27 GHz本振。对波导—微带过渡结构进行仿真,并给出仿真结果。从测试结果表明,模块设计实现了低杂散和低相位噪声。

  3. Logic Pulse Width Modulation Method for Converter%变换器的逻辑脉冲宽度调制方法

    Institute of Scientific and Technical Information of China (English)

    魏毅立; 周金生; 罗家涛; 张自雷

    2014-01-01

    分析了单相半桥DC-AC变换器的逻辑脉冲宽度调制( LPWM)控制方法,阻感负载电流为正和为负情形下IGBT的导通状态,进而分别给出了等效电路。其方法是根据负载的电流的正负而开放或封锁对应的IGBT的门极脉冲。在单相半桥DC-AC变换器的LPWM基础上,分析了三相桥式DC-AC变换器的LPWM控制方法和SVPWM的LPWM控制方法, LPWM控制方法的优点是减少了一半的门极驱动损耗,除电流过零点以外无需再加死区,提高了开关频率,增强了系统的安全性。然后再通过Matlab仿真软件对LPWM仿真,验证了LPWM控制方法正确性。%The logic pulse width modulation ( LPWM) control method for single-phase half bridge DC-AC convert-er, and the on-off state of IGBT under the circumstance of inductive load with the load current as positive and nega-tive respectively have been analyzed in this paper, so as to present the equivalent circuits.This method is to open or close the corresponding IGBT trigger pulse according to the load current being positive or negative.In addition, based on the LPWM control method for the single-phase half bridge DC-AC converter, LPWM control methods for the three-phase bridge DC-AC converter and SVPWM control method have been also analyzed.The advantage of LP-WM control method is to reduce half of the switching loss.No dead zone is need to add up except for the current pass-ing through the zero point, so as to improve the switch frequency and enhance the system safety.Simulation results based on Matlabverify the correctness of LPWM control method.

  4. Design, Control, and Modeling of a New Voltage Source Converter for HVDC System

    Science.gov (United States)

    Mohan, Madhan; Singh, Bhim; Ketan Panigrahi, Bijaya

    2013-05-01

    Abstract: A New Voltage Source Converter (VSC) based on neutral clamped three-level circuit is proposed for High Voltage DC (HVDC) system. The proposed VSC is designed in a multipulse configuration. The converter is operated by Fundamental Frequency Switching (FFS). A new control method is developed for achieving all the necessary control aspects of HVDC system such as independent real and reactive power control, bidirectional real and reactive power control. The basic of the control method is varying the pulse width and by keeping the dc link voltage constant. The steady state and dynamic performances of HVDC system interconnecting two different frequencies network are demonstrated for active and reactive power control. Total number of transformers used in this system are reduced to half in comparison with the two-level VSCs for both active and reactive power control. The performance of the HVDC system is improved in terms of reduced harmonics level even at fundamental frequency switching. The harmonic performance of the designed converter is also studied for different value of the dead angle (β), and the optimized range of the dead angle is achieved for varying reactive power requirement. Simulation results are presented for the designed three level multipulse voltage source converters with the proposed control algorithm.

  5. Intelligent decision support system of operation-optimization in copper smelting converter

    Institute of Scientific and Technical Information of China (English)

    姚俊峰; 梅炽; 彭小奇; 周安梁; 吴冬华

    2002-01-01

    An artificial intelligence technique was applied to the optimization of flux-adding systems and air-blasting systems, the display of on-line parameters, forecasting of mass and compositions of slag in the slagging period, optimization of cold material-adding systems and air-blasting systems, the display of on-line parameters, and the forecasting of copper mass in the copper blow period in copper smelting converters. They were integrated to build the Intelligent Decision Support System of the Operation-Optimization of Copper Smelting Converter(IDSSOOCSC), which is self-learning and self-adaptating. Development steps, monoblock structure and basic functions of the IDSSOOCSC were introduced. After it was applied in a copper smelting converter, every production quota was clearly improved after IDSSOOCSC had been run for 4 months. Blister copper productivity is increased by 6%, processing load of cold input is increased by 8% and average converter life-span is improved from 213 to 235 furnace times.

  6. Monolithically integrated semiconductor optical amplifier and electroabsorption modulator with dual-waveguide spot-size converter input and output

    Science.gov (United States)

    Hou, Lianping; Zhu, Hongliang; Zhou, Fan; Wang, Lufeng; Bian, Jing; Wang, Wei

    2005-09-01

    We have demonstrated an electroabsorption modulator and semiconductor optical amplifier monolithically integrated with novel dual-waveguide spot-size converters (SSC) at the input and output ports for low-loss coupling to a planar light-guide circuit silica waveguide or cleaved single-mode optical fibre. The device was fabricated by means of selective-area MOVPE growth, quantum well intermixing and asymmetric twin waveguide technologies with only a three-step low-pressure MOVPE growth. For the device structure, in the SOA/EAM section, a double ridge structure was employed to reduce the EAM capacitances and enable high bit-rate operation. In the SSC sections, buried ridge structure (BRS) was incorporated. Such a combination of ridge, ATG and BRS structure is reported for the first time in which it can take advantage of easy processing of the ridge structure and the excellent mode characteristic of BRS. At the wavelength range of 1550-1600 nm, lossless operation with extinction ratios of 25 dB dc and more than 10 GHz 3 dB bandwidth is successfully achieved. The beam divergence angles of the input and output ports of the device are as small as 8.0° × 12.6°, resulting in 3.0 dB coupling loss with a cleaved single-mode optical fibre.

  7. Semiconductor optical amplifier monolithically integrated with an electroabsorption modulator and dual-waveguide spot-size converters

    Science.gov (United States)

    Hou, Lianping; Zhu, Hongliang; Wang, Baojun; Zhou, Fan; Wang, Lufeng; Bian, Jing; Wang, Wei

    2005-09-01

    We have demonstrated an electroabsorption modulator and semiconductor optical amplifier monolithically integrated with novel dual-waveguide spot-size converters (SSC) at the input and output ports for low-loss coupling to planar light-guide circuit silica waveguide or cleaved single-mode optical fiber. The device was fabricated by means of selective-area MOVPE growth, quantum well intermixing and asymmetric twin waveguide technologies with only a three steps low-pressure MOVPE growth. For the device structure, in SOA/EAM section, double ridge structure was employed to reduce the EAM capacitances and enable high bit-rate operation. In the SSC sections, buried ridge structure (BRS) were incorporated. Such combination of ridge, ATG and BRS structure is reported for the first time in which it can take advantage of easy processing of ridge structure and the excellent mode characteristic of BRS. At the wavelength range of 1550~1600nm, lossless operation with extinction ratios of 25 dB dc and more than 10 GHz 3-dB bandwidth is successfully achieved. The beam divergence angles of the input and output ports of the device are as small as 8.0°×12.6°, resulting in 3.0 dB coupling loss with cleaved single-mode optical fiber.

  8. Method and appartus for converting static in-ground vehicle scales into weigh-in-motion systems

    Energy Technology Data Exchange (ETDEWEB)

    Muhs, Jeffrey D. (Lenior City, TN); Scudiere, Matthew B. (Oak Ridge, TN); Jordan, John K. (Oak Ridge, TN)

    2002-01-01

    An apparatus and method for converting in-ground static weighing scales for vehicles to weigh-in-motion systems. The apparatus upon conversion includes the existing in-ground static scale, peripheral switches and an electronic module for automatic computation of the weight. By monitoring the velocity, tire position, axle spacing, and real time output from existing static scales as a vehicle drives over the scales, the system determines when an axle of a vehicle is on the scale at a given time, monitors the combined weight output from any given axle combination on the scale(s) at any given time, and from these measurements automatically computes the weight of each individual axle and gross vehicle weight by an integration, integration approximation, and/or signal averaging technique.

  9. Extrapolation of extreme response for different mooring line systems of floating wave energy converters

    DEFF Research Database (Denmark)

    Ambühl, Simon; Sterndorff, Martin; Sørensen, John Dalsgaard

    2014-01-01

    Mooring systems for floating wave energy converters (WECs) are a major cost driver. Failure of mooring systems often occurs due to extreme loads. This paper introduces an extrapolation method for extreme response which accounts for the control system of a WEC that controls the loads onto the stru......Mooring systems for floating wave energy converters (WECs) are a major cost driver. Failure of mooring systems often occurs due to extreme loads. This paper introduces an extrapolation method for extreme response which accounts for the control system of a WEC that controls the loads onto...... the structure and the harvested power of the device as well as the fact that extreme loads may occur during operation and not at extreme wave states when the device is in storm protection mode. The extrapolation method is based on shortterm load time series and applied to a case study where up-scaled surge load...

  10. A Practical Module System for LF

    DEFF Research Database (Denmark)

    Schürmann, Carsten; Rabe, Florian

    2009-01-01

    morphisms, which provide a semantically transparent module level and permit to represent logic translations as homomorphisms. Modular LF is a conser- vative extension over LF, and integrates an elaboration of modular into core LF signatures. We have implemented our design in the Twelf system and used......Module Systems for proof assistants provide administrative support for large developments when mechanizing the meta-theory of programming languages and logics. In this paper we describe a module system for the logical framework LF. It is based on two main primitives: signatures and signature...... it to modularize large parts of the Twelf example library....

  11. High efficiency battery converter with SiC devices for residential PV systems

    DEFF Research Database (Denmark)

    Pham, Cam; Teodorescu, Remus; Kerekes, Tamas

    2013-01-01

    The demand for high efficiency and higher power density is a challenge for Si-based semiconductors due to the physical characteristics of material. These can be overcome by employing wide-band-gap materials like SiC. This paper compares a second generator SiC MOSFETs against a normally-on Trench ...... JFETs and theirs performances in a high efficiency battery converter for residential photovoltaic systems. The prototypes are 3 kW converters with more than 98% efficiency and high simplicity and power density....

  12. Evolving point-of-care diagnostics using up-converting phosphor bioanalytical systems.

    Science.gov (United States)

    Ouellette, Amy L; Li, Janice J; Cooper, David E; Ricco, Antonio J; Kovacs, Gregory T A

    2009-05-01

    Up-converting phosphors promise simpler readout systems with less background at a given signal level than many other popular approaches. (To listen to a podcast about this feature, please go to the Analytical Chemistry website at pubs.acs.org/journal/ancham.).

  13. Development of enzymes and enzyme systems by genetic engineering to convert biomass to sugars

    Science.gov (United States)

    TITLE Development of Enzymes and Enzyme Systems by Genetic Engineering to Convert Biomass to Sugars ABSTRACT Plant cellulosic material is one of the most viable renewable resources for the world’s fuel and chemical feedstock needs. Currently ethanol derived from corn starch is the most common li...

  14. International Energy Agency Ocean Energy Systems Task 10 Wave Energy Converter Modeling Verification and Validation

    DEFF Research Database (Denmark)

    Wendt, Fabian F.; Yu, Yi-Hsiang; Nielsen, Kim

    2017-01-01

    This is the first joint reference paper for the Ocean Energy Systems (OES) Task 10 Wave Energy Converter modeling verification and validation group. The group is established under the OES Energy Technology Network program under the International Energy Agency. OES was founded in 2001 and Task 10 ...

  15. Terrestrial solar power system based on Cs-Ba thermionic converter

    Science.gov (United States)

    Ender, A. Ya.; Kuznetsov, V. I.; Sitnov, V. I.; Kushner, E. M.; Malamed, E. P.; Paramonov, D. V.

    1999-01-01

    A new concept of terrestrial, environmentally friendly solar cogeneration system is described. Power generation is accomplished by a cascaded system with the high temperature stage being a Cs-Ba thermionic converter. Its heating is accomplished by a two-stage solar concentrator with a mirror and focon. Thermal efficiency of such a system is close to 100% because all the heat supplied to the heat receiver is utilized.

  16. New topology for DC/DC bidirectional converter for hybrid systems in renewable energy

    Science.gov (United States)

    Lopez, Juan Carlos; Ortega, Manuel; Jurado, Francisco

    2015-03-01

    This article presents a new isolated DC/DC bidirectional converter with soft switching, using a transformer with two voltage taps and two full bridges with insulated-gate bipolar transistors (IGBTs), one on each side of the transformer to be integrated in hybrid systems of renewable energy. A large voltage conversion ratio can be achieved using this converter, in buck and booster modes. Also medium and high DC power can be converted with a good efficiency. Analysis and switching techniques have been reported. To verify the principle of operation, a laboratory prototype of 10 kW has been performed. Experimental results are presented, operating in boost mode. The switching algorithm used has been modelled in MATLAB-Simulink to generate C code. This code has been implemented in a DSP F2812, which has been used to build the prototype.

  17. Novel system for modulated lidar parameter optimization

    Institute of Scientific and Technical Information of China (English)

    Bo Zhou; Yong Ma; Kun Liang; Zhiqiang Tu; Hongyuan Wang

    2011-01-01

    We present a novel system for parameter design and optimization of modulated lidar. The system is realized by combining software simulation with hardware circuit. This method is more reliable and flexible for lidar parameter optimization compared with theoretical computation or fiber-simulated system. Experiments confirm that the system is capable of optimizing parameters for modulated lidar. Key parameters are analyzed as well. The optimal filter bandwidth is 200 MHz and the optimal modulation depth is 0.5 under typical application environment.%@@ We present a novel system for parameter design and optimization of modulated lidar.The system is realized by combining software simulation with hardware circuit.This method is more reliable and flexible for lidar parameter optimization compared with theoretical computation or fiber-simulated system.Experiments confirm that the system is capable of optimizing parameters for modulated lidar.Key parameters are analyzed as well.The optimal filter bandwidth is 200 MHz and the optimal modulation depth is 0.5 under typical application environment.

  18. Cost-effective bidirectional digitized radio-over-fiber systems employing sigma delta modulation

    Science.gov (United States)

    Lee, Kyung Woon; Jung, HyunDo; Park, Jung Ho

    2016-11-01

    We propose a cost effective digitized radio-over-fiber (D-RoF) system employing a sigma delta modulation (SDM) and a bidirectional transmission technique using phase modulated downlink and intensity modulated uplink. SDM is transparent to different radio access technologies and modulation formats, and more suitable for a downlink of wireless system because a digital to analog converter (DAC) can be avoided at the base station (BS). Also, Central station and BS share the same light source by using a phase modulation for the downlink and an intensity modulation for the uplink transmission. Avoiding DACs and light sources have advantages in terms of cost reduction, power consumption, and compatibility with conventional wireless network structure. We have designed a cost effective bidirectional D-RoF system using a low pass SDM and measured the downlink and uplink transmission performance in terms of error vector magnitude, signal spectra, and constellations, which are based on the 10MHz LTE 64-QAM standard.

  19. The New Control and Interlock System for the SPS Main Power Converters

    CERN Document Server

    Denis, B; Mugnier, C; Varas, J

    1999-01-01

    The Control and Interlock System (CIS) of the SPS main power converters was designed in the mid-70s and became increasingly difficult to maintain. A new system based on Programmable Logic Controllers has been developed by an external contractor in close collaboration with CERN. The system is now operational and fully integrated in the SPS/LEP control infrastructure. The CIS is the first major contracted industrial solution used to control accelerator equipment directly involved in the production of particle beams at CERN. This paper gives an overview of the SPS main power converter installation and describes both the contractual and technical solution adopted for the CIS. It first explains how the system was specified and how the contractual relationship was defined to respect CERN’s purchasing rules and the operational requirements of the SPS accelerator. The architectural design of the new system is presented with special emphasis on how the conflict between safety and availability has been addressed.

  20. Advanced Energy Conversion System Using Sinusoidal Voltage Tracking Buck-Boost Converter Cascaded Polarity Changing Inverter

    Science.gov (United States)

    Ahmed, Nabil A.

    2011-06-01

    This paper presents an advanced power converter employs a sinusoidal voltage absolute value tracking buck-boost DC-DC converter in the first power processing stage and a polarity changing full-bridge inverter in the second stage. The proposed power conversion system has the capability of delivering sinusoidal output and input current with unity power factor and good output voltage regulation. Consequently, the complete voltage regulator system, which is mainly suitable for new energy generation systems as well as energy storage systems, can be constructed compactly and inexpensively without DC link electrolytic capacitor. Also, the paper presents an auxiliary passive resonant circuit for soft switching operation. Simulation results using PSIM software are presented to verify the operation principles and feasibility of the proposed power conversion system.

  1. Ion transport membrane module and vessel system

    Science.gov (United States)

    Stein, VanEric Edward; Carolan, Michael Francis; Chen, Christopher M.; Armstrong, Phillip Andrew; Wahle, Harold W.; Ohrn, Theodore R.; Kneidel, Kurt E.; Rackers, Keith Gerard; Blake, James Erik; Nataraj, Shankar; van Doorn, Rene Hendrik Elias; Wilson, Merrill Anderson

    2008-02-26

    An ion transport membrane system comprising (a) a pressure vessel having an interior, an exterior, an inlet, and an outlet; (b) a plurality of planar ion transport membrane modules disposed in the interior of the pressure vessel and arranged in series, each membrane module comprising mixed metal oxide ceramic material and having an interior region and an exterior region, wherein any inlet and any outlet of the pressure vessel are in flow communication with exterior regions of the membrane modules; and (c) one or more gas manifolds in flow communication with interior regions of the membrane modules and with the exterior of the pressure vessel.The ion transport membrane system may be utilized in a gas separation device to recover oxygen from an oxygen-containing gas or as an oxidation reactor to oxidize compounds in a feed gas stream by oxygen permeated through the mixed metal oxide ceramic material of the membrane modules.

  2. Experimental Demonstration of Ideal Noise Shaping in Resonant Tunneling Delta-Sigma Modulator for High Resolution, Wide Band Analog-to-Digital Converters

    Science.gov (United States)

    Maezawa, Koichi; Sakou, Mario; Matsubara, Wataru; Mizutani, Takashi; Matsuzaki, Hideaki

    2006-04-01

    A ΔΣ modulator using a frequency modulation intermediate signal was demonstrated using a resonant tunneling logic gate called a monostable bistable transition logic element (MOBILE). This ΔΣ modulator is based on the nature of an FM signal and suitable for high-speed operation. Experiments using an InP-based MOBILE demonstrate good noise shaping characteristics. Moreover, the operation with a higher FM carrier frequency than the sampling frequency was demonstrated, showing equally good noise shaping performance. This makes the design of the voltage-controlled oscillator, which is a key component of the FM ΔΣ modulator, much easier. Consequently, an FM ΔΣ modulator using MOBILE is promising for high-resolution, wide-band analog-to-digital converters (ADCs).

  3. A High-Efficient Low-Cost Converter for Capacitive Wireless Power Transfer Systems

    Directory of Open Access Journals (Sweden)

    Il-Oun Lee

    2017-09-01

    Full Text Available Growth of the Internet of Things (IoT spurs need for new ways of delivering power. Wireless power transfer (WPT has come into the spotlight from both academia and industry as a promising way to power the IoT devices. As one of the well-known WPT techniques, the capacitive power transfer (CPT has the merit of low electromagnetic radiation and amenability of combined power and data transfer over a capacitive interface. However, applying the CPT to the IoT devices is still challenging in reality. One of the major issues is due to the small capacitance of the capacitive interface, which results in low efficiency of the power transfer. To tackle this problem, we present a new step-up single-switch quasi-resonant (SSQR converter for the CPT system. To enhance the CPT efficiency, the proposed converter is designed to operate at low frequency and drive small current into the capacitive interfaces. In addition, by eliminating resistor-capacitor-diode (RCD snubber in the converter, we reduce the implementation cost of the CPT system. Based on intensive experimental work with a CPT system prototype that supports maximum 50 W (100 V/0.5 A power transfer, we demonstrate the functional correctness of the converter that achieves up to 93% efficiency.

  4. Module of System Galactica with Coulomb's Interaction

    Directory of Open Access Journals (Sweden)

    Joseph J. Smulsky

    2014-12-01

    Full Text Available The system Galactica of free access is supplemented module for the Coulomb interaction. It is based on a high-precision method for solving differential equations of motion of N charged particles. The paper presents all the theoretical and practical issues required to use this module of system Galactica so that even the beginning researcher could study the motion of particles, atoms and molecules.

  5. MPPT of Magnus Wind System with DC Servo Drive for the Cylinders and Boost Converter

    Directory of Open Access Journals (Sweden)

    Maro Jinbo

    2015-01-01

    Full Text Available This paper presents an algorithm MPPT (Maximum Power Point Tracking for a Magnus wind system with a DC servo drive system (DC drive and BLDC motor to rotate the turbine cylinders. The optimal cylinders rotation is the one to deliver the maximum power extracted from the wind tracked by fixed and adaptive step HCC (Hill Climbing Control acting on the servo drive. The proposed wind system consists of a PMSG (Permanent Magnet Synchronous Generator, a three-phase diode rectifier, a DC/DC (boost converter, and a resistive load. Furthermore, the boost converter acts with the fixed step HCC algorithm to track the maximum power operating point. Therefore, the MPPT for a Magnus wind system requires both tracking for the optimal cylinder speed and the optimal generator speed.

  6. Highly Efficient, Compact, Wavelength Converters for Pulsed and CW Laser Sources Used in Lidar-Based Remote Sensing and Ranging Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — AdvR, Inc. proposes the development of a highly efficient, fiber pigtailed, waveguide-based UV frequency converter module. This UV module will be an important...

  7. A frequency up-converting harvester based on internal resonance in 2-DOF nonlinear systems

    Science.gov (United States)

    Wu, Yipeng; Qiu, Jinhao; Ji, Hongli

    2016-11-01

    This paper reports the design and experimental testing of a novel frequency up- converting piezoelectric energy harvester. The harvester is firstly approximated as a 2-degree- of-freedom cubic nonlinear system instead of the general Duffing systems. A 1:3 internal resonance innovatively applied in the frequency up-conversion approach is thoroughly investigated. Finally, the theoretical dynamic model confirmed by the experimental results clearly shows the effect of the frequency up-conversion.

  8. Convertible source system of thermal neutron and X-ray at Hokkaido University electron linac facility

    Science.gov (United States)

    Kamiyama, T.; Hara, K. Y.; Taira, H.; Sato, H.

    2016-11-01

    The convertible source system for the neutron and the X-ray imagings was installed in the 45MeV electron linear accelerator facility at Hokkaido University. The source system is very useful for a complementary imaging. The imaging measurements for a sample were performed with both beams by using a vacuum tube type image intensifier. The enhanced contrast was obtained from the dataset of the radiograms measured with the neutron and X-ray beams.

  9. Review of modular power converters solutions for smart transformer in distribution system

    DEFF Research Database (Denmark)

    Alzola, Rafael Pena; Gohil, Ghanshyamsinh Vijaysinh; Mathe, Laszlo

    2013-01-01

    While the use of power electronics based Smart Transformer (ST) is becoming a reality in traction applications, and it has been considered as an interesting option for interfacing different transmission systems, the possibility to use it in distribution systems is still considered futuristic....... Replacing primary distribution transformers with ST can lead to more flexible handling of the distribution feeders, while replacing secondary distribution transformers can allow decoupling of distribution network. This paper reviews different power converter solutions for the ST focusing on modularity...

  10. Sliding mode control of boost converter: Application to energy storage system via supercapacitors

    OpenAIRE

    Hijazi, Alaa; Di Loreto, Michaël; BIDEAUX, Eric; Venet, Pascal; Clerc, Guy; Rojat, Gérard

    2009-01-01

    INSPEC Accession Number: 10939325; International audience; Sliding mode control of boost converter is studied. In order to improve dynamical performances with static and dynamic specifications, we propose a systematic procedure to compute the gains of the controller based on an optimization scheme. This method is applied to the control of an energy storage system based on supercapacitors technology in order to regulate the output voltage. Given a system with large variations of input voltage ...

  11. UPFC converter-level control system using internally calculated system quantities for decoupling

    Energy Technology Data Exchange (ETDEWEB)

    Papic, I.; Zunko, P. [Ljubljana Univ., Faculty of Electrical Engineering, Ljubljana (Slovenia)

    2003-10-01

    The paper presents a Unified power flow controller (UPFC) converter-level control system which enables the device to track the changes in reference values of the active and reactive power flow through the transmission line, and of the reactive power exchange with the shunt branch. First, a co-ordinated control of both branches of the device is presented, where all quantities being controlled are also dynamically mutually decoupled. This is possible only if on-line values of input quantities are available in the controller. Under practical operating conditions, the input values are filtered and processed with certain delay, which means that they cannot be directly used for decoupling too. To overcome this problem, a modified control structure was formulated. It is based on the calculation of system quantities in the controller by using the mathematical model of the device. The decoupled UPFC control can significantly reduce interactions with other controls in the system. The derived control was tested with digital simulation (Author)

  12. Histaminergic Mechanisms for Modulation of Memory Systems

    Directory of Open Access Journals (Sweden)

    Cristiano André Köhler

    2011-01-01

    Full Text Available Encoding for several memory types requires neural changes and the activity of distinct regions across the brain. These areas receive broad projections originating in nuclei located in the brainstem which are capable of modulating the activity of a particular area. The histaminergic system is one of the major modulatory systems, and it regulates basic homeostatic and higher functions including arousal, circadian, and feeding rhythms, and cognition. There is now evidence that histamine can modulate learning in different types of behavioral tasks, but the exact course of modulation and its mechanisms are controversial. In the present paper we review the involvement of the histaminergic system and the effects histaminergic receptor agonists/antagonists have on the performance of tasks associated with the main memory types as well as evidence provided by studies with knockout models. Thus, we aim to summarize the possible effects histamine has on modulation of circuits involved in memory formation.

  13. Monolithic integration of optical mode-size converter and high-speed electroabsorption modulators using laterally undercut waveguide

    Science.gov (United States)

    Wu, Tsu-Hsiu; Lin, Fang-Zheng; Yan, Hung-Jung; Wu, Jui-Pin; Chiu, Yi-Jen

    2010-02-01

    A new monolithic integration scheme of fabricating optical spot-size converter (SSC) is realized in this work. High-speed electroabsorption modulator (EAM) is used to integrate such SSC. By laterally tapering the active region of an optical waveguide through undercut active region, a vertically asymmetric waveguide coupler can be defined to form an SSC, where the top is a tapered active waveguide, and the bottom is a large core of passive waveguide mode-matched to single-mode fiber (SMF). Through the top tapered active waveguide, the effective index can be gradually varied in the propagation direction, momentarily matching the bottom low-index passive waveguide. It not only performs the resonant coupling in such asymmetric waveguide coupler, but also locks the transferred power by the tapered structure. InGaAsP/InP multiple quantum wells are used as active region of active waveguide. Based on the highly selective etching properties between InGaAsP and InP, the tapered active waveguide can be fabricated by a method, called selectively undercut-etching-active-region (UEAR), enabling the processing a narrow waveguide structure (up to submicron) by general wet etching from a large waveguide ridge. It also leads to good microwave performance of waveguide. By taking this advantage, a SSC-integrated EAM can perform high-speed electrical-to-optical (EO) response as well as low-insertion loss properties. A mode transfer efficiency of 70% is obtained in such SSC. By narrowing waveguide by UEAR, over 40 GHz of -3dB electrical-to-optical (EO) response is obtained from this device. The high efficient SSC integrated with high-speed EAM suggests that the UEAR technique can have potential for applications in high-speed optoelectronic fields.

  14. Boost Converter Fed High Performance BLDC Drive for Solar PV Array Powered Air Cooling System

    Directory of Open Access Journals (Sweden)

    Shobha Rani Depuru

    2017-01-01

    Full Text Available This paper proposes the utilization of a DC-DC boost converter as a mediator between a Solar Photovoltaic (SPV array and the Voltage Source Inverters (VSI in an SPV array powered air cooling system to attain maximum efficiency. The boost converter, over the various common DC-DC converters, offers many advantages in SPV based applications. Further, two Brushless DC (BLDC motors are employed in the proposed air cooling system: one to run the centrifugal water pump and the other to run a fan-blower. Employing a BLDC motor is found to be the best option because of its top efficiency, supreme reliability and better performance over a wide range of speeds. The air cooling system is developed and simulated using the MATLAB/Simulink environment considering the steady state variation in the solar irradiance. Further, the efficiency of BLDC drive system is compared with a conventional Permanent Magnet DC (PMDC motor drive system and from the simulated results it is found that the proposed system performs better.

  15. Phase-Modulated Optical Communication Systems

    CERN Document Server

    Ho, Keang-Po

    2005-01-01

    Fiber-optic communication systems have revolutionized our telecommunication infrastructures – currently, almost all telephone land-line, cellular, and internet communications must travel via some form of optical fibers. In these transmission systems, neither the phase nor frequency of the optical signal carries information – only the intensity of the signal is used. To transmit more information in a single optical carrier, the phase of the optical carrier must be explored. As a result, there is renewed interest in phase-modulated optical communications, mainly in direct-detection DPSK signals for long-haul optical communication systems. When optical amplifiers are used to maintain certain signal level among the fiber link, the system is limited by amplifier noises and fiber nonlinearities. Phase-Modulated Optical Communication Systems surveys this newly popular area, covering the following topics: The transmitter and receiver for phase-modulated coherent lightwave systems Method for performance analysis o...

  16. Robust Vehicle Suspension System by Converting Active & Passive Control of a Vehicle to Semi-Active Control System Analytically

    Directory of Open Access Journals (Sweden)

    Hassan Elahi

    2014-12-01

    Full Text Available In this research work a simplified translational model of an automotive suspension system is constructed by only considering the translation motion of one wheel of a car. Passive Vehicle Suspension System is converted into Semi Active Vehicle System. Major advantage achieved by this system is that it adjusts the damping of the suspension system without the application of any actuator by using MATLAB® simulations. The semi-active control is found to control the vibration of suspension system very well.

  17. Interconnected High-Voltage Pulsed-Power Converters System Design for H− Ion Sources

    CERN Document Server

    Aguglia, D

    2014-01-01

    This paper presents the design and experimental validations of a system of three new high-voltage (HV) pulsedpower converters for the H− sources. The system requires three pulsed voltages (50, 40, and 25 kV to ground) at 2-Hz repetition rate, for 700 μs of usable flat-top. The solution presents ripplefree output voltages and minimal stored energy to protect the ion source from the consequences of arc events. Experimental results on the final full-scale prototype are presented. In case of short-circuit events, the maximal energy delivered to the source is in the Joule range. HV flat-top stability of 1% is experimentally achieved with a simple Proportional-Integral- Derivative regulation and preliminary tuned H− source (e.g., radio frequency control, gas injection, and so forth). The system is running since more than a year with no power converter failures and damage to the source.

  18. Photonic Routing Systems Using All-optical, Hybrid Integrated Wavelength Converter Arrays

    Directory of Open Access Journals (Sweden)

    Leontios Stampoulidis

    2010-02-01

    Full Text Available The integration of a new generation of all-optical wavelength converters within European project ISTMUFINS has enabled the development of compact and multi-functional photonic processing systems. Here we present the realization of demanding functionalities required in high-capacity photonic routers using these highly integrated components including: Clock recovery, data/label recovery, wavelength routing and contention resolution; all implemented with multi-signal processing using a single photonic chip – a quadruple array of SOAMZI wavelength converters which occupies a chip area of only 15 x 58 mm2. In addition, we present the capability of the technology to build WDM signal processing systems with the simultaneous operation of four quad devices in a four wavelength burst-mode regenerator. Finally, the potential of the technology to provide photonic systems-onchip is demonstrated with the first hybrid integrated alloptical burst-mode receiver prototype.

  19. New drive converter and digital control for the pulsed power supply system of ASDEX Upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Käsemann, Claus-Peter, E-mail: c.p.kaesemann@ipp.mpg.de [Max Planck Institute for Plasma Physics, Boltzmannstraße 2, 85748 Garching (Germany); Jacob, Christian; Nguyen, Hong Ha; Stobbe, Ferdinand; Mayer, Alois [Max Planck Institute for Plasma Physics, Boltzmannstraße 2, 85748 Garching (Germany); Sachs, Edgar; Klein, Reiner [Siemens AG, Industrial Automation Systems, Gleiwitzer Straße 555, 90475 Nürnberg (Germany)

    2015-10-15

    Highlights: • IGBT converter system with integrated control. • Proven technology reduces time and budget. • Flexibility to be integrated into a 35 years old installation. • Stable control algorithms for static and dynamic speed control. • Possibilities for active and reactive power management. - Abstract: Safety and reliability are major issues for the ASDEX Upgrade (AUG) pulsed power supply systems. To avoid long downtimes during an experimental campaign, fault-prone components have to be identified and treated early. This becomes even more important due to the AUG participation in the EUROfusion Medium Sized Tokamak (MST) program. Operating equipment which is up to 40 years old adds additional complications. This contribution describes one such example where a 35 year old flywheel generator at AUG was identified as fault-prone and pre-emptively upgraded with a new drive converter with integrated control. Most challenging was to adapt a modern converter, originally designed for wind turbines, toward a drive system for a flywheel-motor-generator system. To identify the layout of the controller and the control parameters, accurate modeling and comprehensive simulations were performed. This effort paid off during commissioning and measuring results verified the calculated design values. Finally, the system shows good performance during AUG plasma experiments.

  20. Grid Connected Wind Energy Conversion System Using Three Phase Matrix Converter

    Directory of Open Access Journals (Sweden)

    R.A. Priya

    2015-01-01

    Full Text Available A variable speed Wind Energy Conversion System (WECS with Permanent Magnet Synchronous Generator (PMSG connected to grid through Matrix Converter (MC is proposed in this study. Necessity for increased demand in electrical energy paved way for use of renewable energy sources, one of which is abundant wind energy available in ample. Various Wind Energy Conversion systems have been proposed over the decades, of which various topologies had been projected, where complex topologies are being in existence. Permanent magnet synchronous generator has substantial advantages over conventional generators like less weight and volume and exemption for separate excitation with high precision. The conventional system involves two stage of conversion involving rectification followed by inversion being coupled by a DC link capacitor before fed to a grid, which decreases the efficiency of the system due to power quality issue. To overcome this matrix converter can be utilized to transfer the power from generation stage to the grid; there by an AC-AC converter can transfer power from generator to the grid. The proposed system is designed and tested in MATALB/Simulink environment and the results are effective.

  1. Estimation of Bidirectional Buck/boost DC/DC Converters with Electric Double-Layer Capacitors for Energy Storage Systems

    Science.gov (United States)

    Funabiki, Shigeyuki; Yamamoto, Masayoshi

    Renewable energy such as wind force and solar light has collected the attention as alternative energy sources of fossil fuel. An energy storage system with an electric double-layer capacitor (EDLC), which balances the demand and supply power, is required in order to introduce the electric power generating system that utilizes renewable energy. Currently, the research and development of these energy storage systems are actively carried out. In the energy storage system with an EDLC, the DC/DC converter having the function of the bidirectional power flow and the buck/boost performance is essential as an interface and power control circuit. There are two types of the bidirectional buck/boost DC/DC converters. One type consists of two buck/boost DC/DC converters with one reactor. The other type consists of two sets of two-quadrant DC/DC converters with one reactor. This paper discusses the comparison of these types of DC/DC converters with bidirectional power flow and buck/boost performance. The two types of DC/DC converters are estimated for their application to the energy storage system with the EDLC. As the voltage endurance of the device is lower and the mean current is smaller in the latter type of converter despite of having twice the number of devices compared to the former, the latter type of converter has the advantage of a smaller reactor, i.e., core volume and loss, and lower loss in the converter.

  2. Thermoelectric Generator Power Converter System Configurations: A Review

    DEFF Research Database (Denmark)

    Man, Elena Anamaria; Schaltz, Erik; Rosendahl, Lasse

    2013-01-01

    tracking (MPPT) technique is widely used for TEG systems. The aim of this paper is to create a survey over the existing state-of-the-art TEG system configurations for TE energy harvesting. Depending on the application specifications, a suitable TEG system topology can be designed with the purpose......In a Thermoelectric Generator (TEG) system, the Thermoelectric (TE) modules can be connected in series, parallel or a combination of both. Independent of the module connection, the power production of the TEG changes with the temperature gradient applied at its input. In consequence, the system...

  3. A novel control strategy for load converter of DC isolated distribution system under unbalanced loading conditions

    Institute of Scientific and Technical Information of China (English)

    R. NOROOZIAN; M. ABEDI; G.B. GHAREHPETIAN; S. H. HOSSEINI

    2009-01-01

    A novel control strategy for the load converter supplying the unbalanced AC load in a DC isolated distribution system is presented. The control algorithm results in balanced and sinusoidal load voltages under unbalanced AC loading. The unbalanced load is characterized in the d-q-0 rotating coordinate based on symmetrical sequence components. Also, the mathematical model of the load converter in both a-b-c and d-q-0 coordinates is derived by using the average large signal model. Then, two control strategies for the load converter are presented. The first one uses the conventional d-q-0 controller to ensure the voltage and current regulation. The second one is a newly proposed control strategy based on the decomposition of the voltage and current into instantaneous positive, negative, and zero sequences. These three sequences are controlled independently in their own reference frames as DC signals. The performance of the load converter using these two control strategies is compared. Simulation results show the validity and capability of the newly proposed control strategy.

  4. Protocol converter for serial communication between digital rectifier controllers and a power plant SCADA system

    Directory of Open Access Journals (Sweden)

    Vukić Vladimir Đ.

    2016-01-01

    Full Text Available The paper describes the protocol converter INT-485-MBRTU, developed for serial communication between the thyristor rectifier (based on the proprietary protocol "INT-CPD-05", according to standard RS-485 and the SCADA system (based on protocol "Modbus RTU", of the same standard in the thermal power plant "Nikola Tesla B1". Elementary data on industrial communication protocols and communication gateways were provided. The basic technical characteristics of the "Omron" programmable logic controller CJ series were described, as well as the developed device INT-485-MBRTU. Protocol converters with two versions of communication software were tested, differing only in one control word, intended for a forced successive change of communication sequences, in opposite to automatic sequence relieve. The device iNT-485-MBRTU, with the program for forced successive change of communication sequences, demonstrated the reliability of data transfer of 100 %, in a sample of approximately 480 messages. For nearly the same sample, the same protocol converter, with a version of the program without any type of message identifiers, transferred less than 60 % of the foreseen data. During multiple sixty-hour tests, the reliability of data transfer of at least 99.9979% was recorded, in 100% of the analysed cases, and for a sample of nearly 96,000 pairs of the send and receive messages. We analysed the results and estimated the additional possibilities for application of the INT-485-MBRTU protocol converter.

  5. The Research on Telemetry Modulation System

    Directory of Open Access Journals (Sweden)

    Wu Guo-Hui

    2013-05-01

    Full Text Available To develop the effective aerospace telemetry communication system, for aerospace telemetry communication requirements high-speed, high bandwidth, high efficiency and low interference, puts forward the C-WQPSK(C-W Quadrate Phase- Shift Keying)modulation method. This method based on direct carrier QPSK, didn’t consider baseband pulse signal, and redesigned the modulating waveform, its phase angle jump and jump to change duration time all can be changed. Also it gives the C-WQPSK performance and theory analysis, and with QPSK, FQPSK the performance comparison, Through the MATLAB simulation experiment, verify this modulation method is correctness and effectiveness.

  6. Time Synchronization Module for Automatic Identification System

    Institute of Scientific and Technical Information of China (English)

    Choi Il-heung; Oh Sang-heon; Choi Dae-soo; Park Chan-sik; Hwang Dong-hwan; Lee Sang-jeong

    2003-01-01

    This paper proposed a design and implementation procedure of the Time Synchronization Module (TSM) for the Automatic Identification System (AIS). The proposed TSM module uses a Temperature Compensated Crystal Oscillator (TCXO) as a local reference clock, and consists of a Digitally Controlled Oscillator (DCO), a divider, a phase discriminator, and register blocks. The TSM measures time difference between the 1 PPS from the Global Navigation Satellite System (GNSS) receiver and the generated transmitter clock. The measured time difference is compensated by controlling the DCO and the transmit clock is synchronized to the Universal Time Coordinated (UTC). The designed TSM can also be synchronized to the reference time derived from the received message. The proposed module is tested using the experimental AIS transponder set. The experimental results show that the proposed module satisfies the functional and timing specification of the AIS technical standard, ITU-R M.1371.

  7. Acquisition system for the CLIC Module

    CERN Document Server

    Vilalte, Sebastien

    2011-01-01

    The status of R&D activities for CLIC module acquisition are discussed [1]. LAPP is involved in the design of the local CLIC module acquisition crate, described in the document Study of the CLIC Module Front-End Acquisition and Evaluation Electronics [2]. This acquisition system is a project based on a local crate, assigned to the CLIC module, including several mother boards. These motherboards are foreseen to hold mezzanines dedicated to the different subsystems. This system has to work in radiation environment. LAPP is involved in the development of Drive Beam stripline position monitors read-out, described in the document Drive Beam Stripline BPM Electronics and Acquisition [3]. LAPP also develops a generic acquisition mezzanine that allows to perform all-around acquisition and components tests for drive beam stripline BPM read-out.

  8. [Practical experience about the compatibility of PDF converter in ECG information system].

    Science.gov (United States)

    Yang, Gang; Lu, Weishi; Zhou, Jiacheng

    2009-11-01

    To find a way to view ECG from different manufacturers in electrocardiogram information system. Different format ECG data were transmitted to ECG center by different ways. Corresponding analysis software was used to make the diagnosis reports in the center. Then we use PDF convert to change all ECG reports into PDF format. The electrocardiogram information system manage these PDF format ECG data for clinic user. The ECG reports form several major ECG manufacturers were transformed to PDF format successfully. In the electrocardiogram information system it is freely to view the ECG figure. PDF format ECG report is a practicable way to solve the compatibility problem in electrocardiogram information system.

  9. Optimisation of Working Areas in Discrete Hydraulic Power Take off-system for Wave Energy Converters

    DEFF Research Database (Denmark)

    Hansen, Anders Hedegaard; Hansen, Rico Hjerm; Pedersen, Henrik C.

    2012-01-01

    Fluid power is the leading technology in Power Take Off(PTO) systems in Wave Energy Converters(WEC’s), due to the capability of generating high force at low velocity. However, as hydraulic force controlling system may suffer from large energy losses the efficiency of the hydraulic PTO systems may...... be a limiting factor for wave energy. Therefore, a secondary controlled force system has been proposed as PTO element for WEC’s. This paper investigates the configuration of a multi-chamber cylinder utilising two common pressure lines. By usage of model based optimisation an optimal number and size of working...

  10. A review and design of power electronics converters for fuel cell hybrid system applications

    DEFF Research Database (Denmark)

    Zhang, Zhe; Pittini, Riccardo; Andersen, Michael A. E.

    2012-01-01

    This paper presents an overview of most promising power electronics topologies for a fuel cell hybrid power conversion system which can be utilized in many applications such as hybrid electrical vehicles (HEV), distributed generations (DG) and uninterruptible-power-supply (UPS) systems. Then......, a multiple-input power conversion system including a decoupled dual-input converter and a three-phase neutral-point-clamped (NPC) inverter is proposed. The system can operate in both stand-alone and grid-connected modes. Simulation and experimental results are provided to show the feasibility of the proposed...

  11. Non-Fragile H∞Control for Random Pulse Width Modulation of DCM Boost Converter%DCM Boost变换器随机PWM非脆弱H∞控制

    Institute of Scientific and Technical Information of China (English)

    冉华军; 李翔; 肖鹏

    2014-01-01

    引入两模态马尔科夫链随机PWM策略到DCM Boost变换器,推导建立了变换器的离散随机跳变模型,并基于随机跳变系统非脆弱H∞控制理论为Boost变换器设计了非脆弱H∞控制器,利用Simulink软件平台设计仿真电路进行验证。仿真分析表明,设计的控制器改善了Boost变换器的EMI品质,对控制器参数摄动表现出非脆弱性,使整个变换器系统具有较好的鲁棒性。%The two-state-Markov-chain random pulse width modulation (PWM) scheme was introduced into the DCM Boost converter. This paper derived the random discrete-time jumping model of the converter and designed the non-fragile H∞ con-troller based on non-fragile H∞ control theory of stochastic jumping system. The simulation was done to check the validity of non-fragile H∞controller on the Simulink platform. The simulation analysis indicates that the designed controller has improved the EMI quality of Boost converter along with non-fragility to its parameters uncertainty, and with better robust for the whole converter system.

  12. 1 kW, 9 kV dc-dc converter module with time-sharing control of output voltage and input current

    Energy Technology Data Exchange (ETDEWEB)

    Borgatti, R.; Stefani, R.; Bressan, O.; Bicciato, F. [F.I.A.R. Electronic Systems Group, Milan (Italy). Avionics Div.; Tenti, P.; Rossetto, L. [Univ. of Padova (Italy). Dept. of Electrical Engineering

    1993-10-01

    The paper describes a dc-dc power module based on a single-stage current-fed converter structure. Control is made according to a time-sharing strategy allowing simultaneous regulation of output voltage and input current. This solution is suitable for high-performance space and avionic applications, giving high efficiency, compactness, and accuracy, speed and robustness of control. Theoretical analysis, design criteria, and experimental results are reported. Application to radar supplies is discussed.

  13. Modelling and Simulation of Closed Loop Controlled Buck Converter Fed Pmbldc Drive System

    Directory of Open Access Journals (Sweden)

    R. Dhanasekaran

    2011-04-01

    Full Text Available Permanent Magnet Brushless DC Motor (PMBLDC is one of the best electrical drives that has increasing popularity, due to their high efficiency, reliability, good dynamic response and very low maintenance. This makes the interest of modeling an ideal PMBLDC motor and it’s associated Drive System in simple and lucid manner. In this paper the drive system is proposed with a buck converter topology. It has the advantages of reduced switching losses, low inductor power loss, reduced ripple by using a pi-filter, which in turn makes the DC link voltage to be stable. The modeling and simulation of the PMBLDC motor is done using the software package MATLAB/SIMULINK. The operation principle of the buck converter is analyzed and the simulation results are presented in this paper to verify the theoretical analysis.

  14. Wavelength Converters

    DEFF Research Database (Denmark)

    Kloch, Allan; Hansen, Peter Bukhave; Wolfson, David;

    1999-01-01

    at 2.5 Gbit/s, the regeneration causes a reduction of the required input power to an in-line EDFA of ~6 dB for a power penalty of 1 dB at a bit error rate of 10-9. If two converters are concatenated the power requirement is reduced ~8 dB. Obviously, the power reduction allows for longer spans between....... It is predicted that jitter accumulation can be minimised by using a 9-10 dB ratio between the signal and CW power also assuring a high extinction ratio. Using this guideline simulations show that 20 cross-gain modulation converters can be cascaded at 10 Gbit/s with only ~20 ps of accumulated jitter...... and an extinction ratio of ~10 dB.The regenerative capabilities of the cross-phase converters are described and verified experimentally at 20 Gbit/s, where the noise redistribution and improvement of the signal-to-noise ratio clearly is demonstrated by controlling the input power to an EDFA. In a similar experiment...

  15. A power conversion system for PMSG-based WECS operating with fully-controlled current-source converters

    Institute of Scientific and Technical Information of China (English)

    Jian-yu BAO; Wei-bing BAO; Yu-ling LI

    2014-01-01

    We propose a new power conversion system for a permanent magnet synchronous generator (PMSG) based grid-connected wind energy conversion system (WECS) operating with fully-controlled back-to-back current-source converters. On the generator side, two independent current-source rectifiers (CSRs) with space-vector pulse width modulation (SVPWM) are employed to regulate and stabilize DC-link currents. Between DC-link and the electrical grid, a direct-type three-phase five-level current-source inverter (CSI) is inserted as a buffer to regulate real and reactive power fed to the grid and thus adjusts the grid side power-factor. We also present a current-based maximum power point tracking (MPPT) scheme, which helps the generator extract the maximum power through closed-loop regulation of the generator speed. By applying the multilevel modulation and control strategies to the grid-side five-level CSI, a multilevel output current waveform with less distortion is produced, and the bulk requirement of the output capacitor filter to eliminate the harmonic current is reduced. All the proposed concepts are verified by simulation models built in a PSIM environment.

  16. Boost converter with combined control loop for a stand-alone photovoltaic battery charge system

    DEFF Research Database (Denmark)

    Mira Albert, Maria del Carmen; Knott, Arnold; Thomsen, Ole Cornelius

    2013-01-01

    The converter control scheme plays an important role in the performance of maximum power point tracking (MPPT) algorithms. In this paper, an input voltage control with double loop for a stand-alone photovoltaic system is designed and tested. The inner current control loop with high crossover...... is linearized at the maximum power point (MPP) and at the voltage and current source regions. A settling time under 1 ms is obtained which allows fast MPP tracking implementation....

  17. Impedance matching and DC-DC converter designs for tunable radio frequency based mobile telecommunication systems

    OpenAIRE

    Wong, Yan Chiew

    2014-01-01

    Tunability and adaptability for radio frequency (RF) front-ends are highly desirable because they not only enhance functionality and performance but also reduce the circuit size and cost. This thesis presents a number of novel design strategies in DC-DC converters, impedance networks and adaptive algorithms for tunable and adaptable RF based mobile telecommunication systems. Specifically, the studies are divided into three major directions: (a) high voltage switch controller ba...

  18. A Predictive Power Control Strategy for DFIGs Based on a Wind Energy Converter System

    Directory of Open Access Journals (Sweden)

    Xiaoliang Yang

    2017-07-01

    Full Text Available A feasible control strategy is proposed to control a doubly fed induction generator based on the wind energy converter system (DFIG-WECS. The main aim is to enhance the steady state and dynamic performance under the condition of the parameter perturbations and external disturbances and to satisfy the stator power response of the system. Within the proposed control method, the control scheme for the rotor side converter (RSC is developed on the model predictive control. Firstly, the self-adaptive reference trajectory is established from the deduced discrete state-space equation of the generator. Then, the rotor voltage is calculated by minimizing the global performance index under the current prediction steps at the sampling instant. Through the control scheme for the grid side converter (GSC and wind turbine, we have re-applied the conventional control. The effectiveness of the proposed control strategy is verified via time domain simulation of a 150 kW-575 V DFIG-WECS using Matlab/Simulink. The simulation result shows that the control of the DFIG with the proposed control method can enhance the steady and dynamic response capability better than the conventional ones when the system faces errors due to the parameter perturbations, external disturbances and the rotor speed.

  19. Application of Dual Throttling Air-Conditioning System to Explosion-Proof Frequency Converter

    Institute of Scientific and Technical Information of China (English)

    张于峰; 高岩; 盛颖

    2015-01-01

    An explosion-proof dual throttling air-conditioning system was put forward to solve the heat dissipation and internal dewing problems of explosion-proof frequency converter in the underground coal mine. This study inves-tigated the feasibility and benefits of explosion-proof dual throttling cooling and dehumidification air-conditioning system applied to the explosion-proof frequency converter. The physical model of dual throttling air-conditioning sys-tem was established and its performance parameter was described by mathematical method. The design calculation of the system has also been done. The experimental result showed that the system reached the steady state at the refrig-eration mode after running 45 min, and the maximum internal temperature of the flame-proof cavity was 31.0℃. The system reached the steady state at the dehumidification mode after running 37 min. The maximum internal relative humidity and temperature of the flame-proof cavity were 33.4% and 36.3 ℃, respectively. Therefore, the proposed system had excellent ability of heat dissipation and avoided internal dewing. Compared with water cooling system, it was more energy-saving and economical. The airflow field of dual throttling air-conditioning system was also studied by CFD simulation. It was found that the result of CFD numerical simulation was highly consistent with the experi-mental data.

  20. Comparison and Sensitivity Investigations of a CALM and SALM Type Mooring System for Wave Energy Converters

    OpenAIRE

    Arthur Pecher; Aligi Foglia; Jens Peter Kofoed

    2014-01-01

    A quasi-static analysis and sensitivity investigation of two different mooring configurations—a single anchor leg mooring (SALM) and a three-legged catenary anchor leg system (CALM)—is presented. The analysis aims to indicate what can be expected in terms of requirements for the mooring system size and stiffness. The two mooring systems were designed for the same reference load case, corresponding to a horizontal design load at the wave energy converter (WEC) of 2000 kN and a water depth of 3...

  1. Radiation tolerant power converter controls

    CERN Document Server

    Todd, B; King, Q; Uznanski, S

    2012-01-01

    The Large Hadron Collider (LHC) at the European Organisation for Nuclear Research (CERN) is the world's most powerful particle collider. The LHC has several thousand magnets, both warm and super-conducting, which are supplied with current by power converters. Each converter is controlled by a purpose-built electronic module called a Function Generator Controller (FGC). The FGC allows remote control of the power converter and forms the central part of a closed-loop control system where the power converter voltage is set, based on the converter output current and magnet-circuit characteristics. Some power converters and FGCs are located in areas which are exposed to beam-induced radiation. There are numerous radiation induced effects, some of which lead to a loss of control of the power converter, having a direct impact upon the accelerator's availability. Following the first long shut down (LS1), the LHC will be able to run with higher intensity beams and higher beam energy. This is expected to lead to signifi...

  2. Avoidance High-Frequency Chattering Second-Order Sliding Mode Controller Design: Buck Converter in Wind Power System

    Directory of Open Access Journals (Sweden)

    Yigeng Huangfu

    2012-01-01

    Full Text Available This paper mainly discussed a method of high-frequency second-order sliding mode control for Buck converter in wind power systems. Because the wind energy of nature is always unpredictable and intermittent, the robust control such as sliding mode control is adopted in past literatures. In order to remove the high frequency chattering problem when the traditional sliding mode achieves convergence, the second order sliding mode algorithm is reviewed firstly. Meanwhile, the Buck converter taken as a step-down converter is usually adopted in wind power system, because of its simple structure and good linearity. Under those conditions, the second order sliding mode controller is designed based on Buck converter, especially in high-power wind generation system. The experimental results illustrate that the theory of second order sliding mode can be used in high-power Buck converter. It provides one novel avoidance high frequency chattering method for the technology development of new energy generation system.

  3. Space vector modulation strategy for neutral-point voltage balancing in three-level inverter systems

    DEFF Research Database (Denmark)

    Choi, Uimin; Lee, Kyo Beum

    2013-01-01

    This study proposes a space vector modulation (SVM) strategy to balance the neutral-point voltage of three-level inverter systems. The proposed method is implemented by combining conventional symmetric SVM with nearest three-vector (NTV) modulation. The conventional SVM is converted to NTV...... modulation by properly adding or subtracting a minimum gate-on time. In addition, using this method, the switching frequency is reduced and a decrease of switching loss would be yielded. The neutral-point voltage is balanced by the proposed SVM strategy without additional hardware or complex calculations...

  4. Plasmon absorption modulator systems and methods

    Science.gov (United States)

    Kekatpure, Rohan Deodatta; Davids, Paul

    2014-07-15

    Plasmon absorption modulator systems and methods are disclosed. A plasmon absorption modulator system includes a semiconductor substrate, a plurality of quantum well layers stacked on a top surface of the semiconductor substrate, and a metal layer formed on a top surface of the stack of quantum well layers. A method for modulating plasmonic current includes enabling propagation of the plasmonic current along a metal layer, and applying a voltage across the stack of quantum well layers to cause absorption of a portion of energy of the plasmonic current by the stack of quantum well layers. A metamaterial switching system includes a semiconductor substrate, a plurality of quantum well layers stacked on a top surface of the semiconductor substrate, and at least one metamaterial structure formed on a top surface of the stack of quantum well layers.

  5. Investigation and Optimisation of a Discrete Fluid Power PTO-system for Wave Energy Converters

    DEFF Research Database (Denmark)

    Hansen, Anders Hedegaard

    recently focused research on improving the power take off (PTO) system converting the mechanical motion of the floats into electricity. This has brought attention to discrete fluid power (DFP) technology, especially secondary controlled common pressure rail systems. A novel discrete PTO-system has been...... proposed and found feasible for the Wavestar WEC. However, with a technology shift from a continuous to a discrete fluid power PTO-system, new challenges emerge. The current project investigates and optimises the novel discrete fluid power PTO-system proposed for the Wavestar WEC. Initiating from...... an investigation of energy extraction by WECs utilising a discrete PTO force, an investigation of the system configuration is conducted. Hence, the configuration of the multi-chamber cylinder and the common pressure rails are investigated for the discrete fluid power force system. A method for choosing the system...

  6. Multi-Input Converter with MPPT Feature for Wind-PV Power Generation System

    Directory of Open Access Journals (Sweden)

    Chih-Lung Shen

    2013-01-01

    Full Text Available A multi-input converter (MIC to process wind-PV power is proposed, designed, analyzed, simulated, and implemented. The MIC cannot only process solar energy but deal with wind power, of which structure is derived from forward-type DC/DC converter to step-down/up voltage for charger systems, DC distribution applications, or grid connection. The MIC comprises an upper modified double-ended forward, a lower modified double-ended forward, a common output inductor, and a DSP-based system controller. The two modified double-ended forwards can operate individually or simultaneously so as to accommodate the variation of the hybrid renewable energy under different atmospheric conditions. While the MIC operates at interleaving mode, better performance can be achieved and volume also is reduced. The proposed MIC is capable of recycling the energy stored in the leakage inductance and obtaining high step-up output voltage. In order to draw maximum power from wind turbine and PV panel, perturb-and-observe method is adopted to achieve maximum power point tracking (MPPT feature. The MIC is constructed, analyzed, simulated, and tested. Simulations and hardware measurements have demonstrated the feasibility and functionality of the proposed multi-input converter.

  7. Stability of large DC power systems using switching converters, with application to the international space station

    Science.gov (United States)

    Manners, B.; Gholdston, E. W.; Karimi, K.; Lee, F. C.; Rajagopalan, J.; Panov, Y.

    1996-01-01

    As space direct current (dc) power systems continue to grow in size, switching power converters are playing an ever larger role in power conditioning and control. When designing a large dc system using power converters of this type, special attention must be placed on the electrical stability of the system and of the individual loads on the system. In the design of the electric power system (EPS) of the International Space Station (ISS), the National Aeronautics and Space Administration (NASA) and its contractor team led by Boeing Defense & Space Group has placed a great deal of emphasis on designing for system and load stability. To achieve this goal, the team has expended considerable effort deriving a dear concept on defining system stability in both a general sense and specifically with respect to the space station. The ISS power system presents numerous challenges with respect to system stability, such as high power, complex sources and undefined loads. To complicate these issues, source and load components have been designed in parallel by three major subcontractors (Boeing, Rocketdyne, and McDonnell Douglas) with interfaces to both sources and loads being designed in different countries (Russia, Japan, Canada, Europe, etc.). These issues, coupled with the program goal of limiting costs, have proven a significant challenge to the program. As a result, the program has derived an impedance specification approach for system stability. This approach is based on the significant relationship between source and load impedances and the effect of this relationship on system stability. This approach is limited in its applicability by the theoretical and practical limits on component designs as presented by each system segment. As a result, the overall approach to system stability implemented by the ISS program consists of specific hardware requirements coupled with extensive system analysis and hardware testing. Following this approach, the ISS program plans to begin

  8. Fault-tolerant design of local controller for the poloidal field converter control system on ITER

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Jun; Fu, Peng; Gao, Ge; He, Shiying; Huang, Liansheng, E-mail: huangls@ipp.ac.cn; Zhu, Lili; Chen, Xiaojiao

    2016-11-15

    Highlights: • The requirements on the Local Control Cubicles (LCC) for ITER Poloidal Field Converter are analyzed. • Decoupled service-based software architecture is proposed to make control loops on LCC running at varying cycle-time. • Fault detection and recovery methods for the LCC are developed to enhance the system. • The performance of the LCC with or without fault-tolerant feature is tested and compared. - Abstract: The control system for the Poloidal Field (PF) on ITER is a synchronously networked control system, which has several kinds of computational controllers. The Local Control Cubicles (LCC) play a critical role in the networked control system for they are the interface to all input and output signals. Thus, some additional work must be done to guarantee the LCCs proper operation under influence of faults. This paper mainly analyzes the system demands of the LCCs and faults which have been encountered recently. In order to handle these faults, decoupled service-based software architecture has been proposed. Based on this architecture, fault detection and system recovery methods, such as redundancy and rejuvenation, have been incorporated to achieve a fault-tolerant private network with the aid of QNX operating system. Unlike the conventional method, this method requires no additional hardware and can be achieved relatively easily. To demonstrate effectiveness the LCCs have been successfully tested during the recent PF Converter Unit performance tests for ITER.

  9. Optimal Operation of Photovoltaic System with a DC-DC Boost Converter FED SAF Using ICosφ Algorithm

    Directory of Open Access Journals (Sweden)

    G.Vijayakumar

    2014-07-01

    Full Text Available This paper presents an optimal utilization of Photovoltaic (PV solar system based Shunt Active Filter (PV-SAF for harmonic mitigation, real and reactive power compensation at the point of common coupling (PCC throughout the day. This PV system operated SAF reduces the energy consumption by disconnecting the utility grid from the load through semiconductor switches, when the PV system generates excessive or equal real power to the required load demand. However, the reduction of energy consumption is always desirable for the reduction of panel tariff and global warming gasses. The PV module is connected to the DC side of SAF through the DC-DC converter with fuzzy based Perturb & Observe (P&O Maximum Power Point Tracking (MPPT algorithm to eliminate the drawback of the conventional PV system by tracking maximum power point of the PV array is presented. The reference currents extract by the Fuzzy logic controller based ICosΦ control strategy. This proposed PV-SAF, if connected at the terminals of a small industry or a home or a small enlightening institution can avoid interruptible power supply, use of individual stabilizer and potential panel tariff over a 12 hour period. A MATLAB simulink is presented to validate the advantage of the proposed system.

  10. Modeling and Simulation of Generator Side Converter of Doubly Fed Induction Generator-Based Wind Power Generation System

    DEFF Research Database (Denmark)

    Guo, Yougui; Zeng, Ping; Blaabjerg, Frede

    2010-01-01

    A real wind power generation system is given in this paper. SVM control strategy and vector control is applied for generator side converter and doubly fed induction generator respectively. First the mathematical models of the wind turbine rotor, drive train, generator side converter are described...

  11. Power Control of Offshore Wind Power System through Modular Multilevel Converter

    DEFF Research Database (Denmark)

    Hakimi, Mehdi; Hajizadeh, Amin

    2017-01-01

    This paper presents an Adaptive Fuzzy Sliding Mode (AFSM) Current Control of Modular Multilevel Converter (MMC) for integration offshore wind power system to on-grid network. In order to design adaptive robust control strategy, mathematical dynamic model of MMC using rotating d-q theory based upon...... positive and negative symmetrical components has been developed. Time-domain simulation studies are carried out in the Matlab/Simulink environment to verify the performance of the overall proposed control system. The simulation results show that the proposed controller provides the load with a set...

  12. An adaptive control strategy of converter based DG to maintain protection coordination in distribution system

    DEFF Research Database (Denmark)

    Su, Chi; Liu, Zhou; Chen, Zhe

    2014-01-01

    Distributed generation (DG) is increasingly integrated into distribution systems due to its flexible onsite characteristic and low carbon emission. However, DG integration may change the fault current pattern in distribution systems, which may in turn degrade the performance and coordination...... of network protection devices. As a protection measure commonly used in distribution network, recloser-fuse coordination could suffer from this impact. Research work has been conducted to deal with this problem by modifying the control strategy of the DG converters during faults. These solutions generally...

  13. A Power Conditioning Stage Based on Analog-Circuit MPPT Control and a Superbuck Converter for Thermoelectric Generators in Spacecraft Power Systems

    Science.gov (United States)

    Sun, Kai; Wu, Hongfei; Cai, Yan; Xing, Yan

    2014-06-01

    A thermoelectric generator (TEG) is a very important kind of power supply for spacecraft, especially for deep-space missions, due to its long lifetime and high reliability. To develop a practical TEG power supply for spacecraft, a power conditioning stage is indispensable, being employed to convert the varying output voltage of the TEG modules to a definite voltage for feeding batteries or loads. To enhance the system reliability, a power conditioning stage based on analog-circuit maximum-power-point tracking (MPPT) control and a superbuck converter is proposed in this paper. The input of this power conditioning stage is connected to the output of the TEG modules, and the output of this stage is connected to the battery and loads. The superbuck converter is employed as the main circuit, featuring low input current ripples and high conversion efficiency. Since for spacecraft power systems reliable operation is the key target for control circuits, a reset-set flip-flop-based analog circuit is used as the basic control circuit to implement MPPT, being much simpler than digital control circuits and offering higher reliability. Experiments have verified the feasibility and effectiveness of the proposed power conditioning stage. The results show the advantages of the proposed stage, such as maximum utilization of TEG power, small input ripples, and good stability.

  14. Analysis and Design of Bi-Directional DC-DC Converter in the Extended Run Time DC UPS System Based on Fuel Cell and Supercapacitor

    DEFF Research Database (Denmark)

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

    2009-01-01

    input voltage combined with load current feedback using PI controller with anti-windup scheme to realize closed-loop control of the whole system, and verify the feasibility of the control scheme proposed by simulation. A 1kW prototype controlled by TMS320F2808 DSP is implemented and tested. Experimental......Abstract-In this paper, an extended run time DC UPS system structure with fuel cell and supercapacitor is investigated. A wide input range bi-directional dc-dc converter is described along with the phase-shift modulation scheme and phase-shift with duty cycle control, in different modes...

  15. Improvement of photovoltaic pumping systems based on standard frequency converters by means of programmable logic controllers

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez-Ramos, Jose [Departamento de Electronica, Universidad de Malaga, Complejo Tecnologico de Teatinos (2.2.39), 29071 Malaga (Spain); Narvarte-Fernandez, Luis; Poza-Saura, Fernando [Instituto de Energia Solar, Universidad Politecnica de Madrid (IES-UPM), Avenida Complutense s/n (204), 28040 Madrid (Spain)

    2010-01-15

    Photovoltaic pumping systems (PVPS) based on standard frequency converters (SFCs) are currently experiencing a growing interest in pumping programmes implemented in remote areas because of their high performance in terms of component reliability, low cost, high power range and good availability of components virtually anywhere in the world. However, in practical applications there have appeared a number of problems related to the adaptation of the SFCs to the requirements of the photovoltaic pumping systems (PVPS). Another disadvantage of dedicated PVPS is the difficulty in implementing maximum power point tracking (MPPT). This paper shows that these problems can be solved through the addition of a basic industrial programmable logic controller (PLC) to the system. This PLC does not increase the cost and complexity of the system, but improves the adaptation of the SFC to the photovoltaic pumping system, and increases the overall performance of the system. (author)

  16. DC to DC converters: operation; Hacheurs: fonctionnement

    Energy Technology Data Exchange (ETDEWEB)

    Bernot, F. [Ecole d' Ingenieurs de Tours, 37 (France)

    2002-05-01

    This article deals with pulse width modulation (PWM) and pulse position modulation (PPM) DC to DC converters. A tri-phase PWM converter is made of 6 simple DC/DC converters grouped together into 3 reversible converters of the same type: 1 - single-quadrant voltage lowering converters (hydraulic analogy, study with ideal elements, full scheme with input and output filters); 2 - single-quadrant voltage raising converters (hydraulic analogy, operation); 3 - two quadrants reversible converters (structure construction, quadrants of operation, reversible converter connected to a DC motor); 4 - four-quadrants reversible converters; 5 - other converters structure (current converters and converters with intermediate storage, asymmetrical converters, converters with capacitive storage, insulated converters, resonating converters, status); 6 - conclusion. (J.S.)

  17. Load converter interactions with the secondary system in the Space Station Freedom power management and distribution dc test bed

    Science.gov (United States)

    Lebron, Ramon C.

    1992-01-01

    The NASA LeRC in Cleveland, Ohio, is responsible for the design, development, and assembly of the Space Station Freedom (SSF) Electrical Power System (EPS). In order to identify and understand system level issues during the SSF program design and development phases, a system Power Management and Distribution (PMAD) dc test bed was assembled. Some of the objectives of this test bed facility are the evaluation of, system efficiency, power quality, system stability, and system protection and reconfiguration schemes. In order to provide a realistic operating scenario, dc Load Converter Units are used in the PMAD dc test bed to characterize the user interface with the power system. These units are dc to dc converters that provide the final system regulation before power is delivered to the load. This final regulation is required on the actual space station because the majority of user loads will require voltage levels different from the secondary bus voltage. This paper describes the testing of load converters in an end to end system environment (from solar array to loads) where their interactions and compatibility with other system components are considered. Some of the system effects of interest that are presented include load converters transient behavior interactions with protective current limiting switchgear, load converters ripple effects, and the effects of load converter constant power behavior with protective features such as foldback.

  18. Load converter interactions with the secondary system in the Space Station Freedom power management and distribution DC test bed

    Science.gov (United States)

    Lebron, Ramon C.

    1992-01-01

    The NASA LeRC in Cleveland, Ohio, is responsible for the design, development, and assembly of the Space Station Freedom (SSF) Electrical Power System (EPS). In order to identify and understand system level issues during the SSF Program design and development phases, a system Power Management and Distribution (PMAD) DC test bed was assembled. Some of the objectives of this test bed facility are the evaluation of, system efficiency, power quality, system stability, and system protection and reconfiguration schemes. In order to provide a realistic operating scenario, dc Load Converter Units are used in the PMAD dc test bed to characterize the user interface with the power system. These units are dc to dc converters that provide the final system regulation before power is delivered to the load. This final regulation is required on the actual space station because the majority of user loads will require voltage levels different from the secondary bus voltage. This paper describes the testing of load converters in an end to end system environment (from solar array to loads) where their interactions and compatibility with other system components are considered. Some of the system effects of interest that are presented include load converters transient behavior interactions with protective current limiting switchgear, load converters ripple effects, and the effects of load converter constant power behavior with protective features such as foldback.

  19. Study of a control strategy for grid side converter in doubly- fed wind power system

    Science.gov (United States)

    Zhu, D. J.; Tan, Z. L.; Yuan, F.; Wang, Q. Y.; Ding, M.

    2016-08-01

    The grid side converter is an important part of the excitation system of doubly-fed asynchronous generator used in wind power system. As a three-phase voltage source PWM converter, it can not only transfer slip power in the form of active power, but also adjust the reactive power of the grid. This paper proposed a control approach for improving its performance. In this control approach, the dc voltage is regulated by a sliding mode variable structure control scheme and current by a variable structure controller based on the input output linearization. The theoretical bases of the sliding mode variable structure control were introduced, and the stability proof was presented. Switching function of the system has been deduced, sliding mode voltage controller model has been established, and the output of the outer voltage loop is the instruction of the inner current loop. Affine nonlinear model of two input two output equations on d-q axis for current has been established its meeting conditions of exact linearization were proved. In order to improve the anti-jamming capability of the system, a variable structure control was added in the current controller, the control law was deduced. The dual-loop control with sliding mode control in outer voltage loop and linearization variable structure control in inner current loop was proposed. Simulation results demonstrate the effectiveness of the proposed control strategy even during the dc reference voltage and system load variation.

  20. COANP-fullerenes system for optical modulation

    Science.gov (United States)

    Likhomanova, S. V.; Kamanina, N. V.

    2016-08-01

    The advanced investigations of ϕ-conjugated organic molecule COANP sensitized with fullerenes have been revealed to consider this system as an affective medium for optical limiting and phase modulation. The special accent has been given to influence of the nanostructured relief at the interface on the spectral and photoconductive features.

  1. Discrete Displacement Hydraulic Power Take-Off System for the Wavestar Wave Energy Converter

    Directory of Open Access Journals (Sweden)

    Enrique Vidal

    2013-08-01

    Full Text Available The Wavestar Wave Energy Converter (WEC is a multiple absorber concept, consisting of 20 hemisphere shaped floats attached to a single platform. The heart of the Wavestar WEC is the Power Take-Off (PTO system, converting the wave induced motion of the floats into a steady power output to the grid. In the present work, a PTO based on a novel discrete displacement fluid power technology is explored for the Wavestar WEC. Absorption of power from the floats is performed by hydraulic cylinders, supplying power to a common fixed pressure system with accumulators for energy smoothing. The stored pressure energy is converted into electricity at a steady pace by hydraulic motors and generators. The storage, thereby, decouples the complicated process of wave power absorption from power generation. The core for enabling this PTO technology is implementing a near loss-free force control of the energy absorbing cylinders. This is achieved by using special multi-chambered cylinders, where the different chambers may be connected to the available system pressures using fast on/off valves. Resultantly, a Discrete Displacement Cylinder (DDC is created, allowing near loss free discrete force control. This paper presents a complete PTO system for a 20 float Wavestar based on the DDC. The WEC and PTO is rigorously modeled from incident waves to the electric output to the grid. The resulting model of +600 states is simulated in different irregular seas, showing that power conversion efficiencies above 70% from input power to electrical power is achievable for all relevant sea conditions.

  2. On the design of pole modules for inverse systems

    Science.gov (United States)

    Wyman, B. F.; Sain, M. K.

    1985-01-01

    When a linear dynamical system admits more than one inverse, it is known that the pole module of any inverse must contain, either as a submodule or as a factor module, a module of fixed poles isomorphic to the zero module of the original system. Design of the pole module for such an inverse system is resolved by introducing a variable pole module for the inverse, by determining necessary and sufficient conditions for a desired module to be a variable pole module, and by studying the manner in which the fixed and variable modules assemble into the pole module of the inverse. If the fixed and variable pole spectra are disjoint, the pole module of the inverse system is a direct sum of the fixed- and variable-pole modules; if not, procedures for addressing the Jordan structure are presented.

  3. Non-Linear Behavioral Modeling for DC-DC Converters and Dynamic Analysis of Distributed Energy Systems

    OpenAIRE

    Xiancheng Zheng; Husan Ali; Xiaohua Wu; Haider Zaman; Shahbaz Khan

    2017-01-01

    In modern distributed energy systems (DES), focus is shifting from the conventional centralized approach towards distributed architectures. However, modeling and analysis of these systems is more complex, as it involves the interface of multiple energy sources with many different type of loads through power electronics converters. The integration of power electronics converters allows distributed renewable energy sources to become part of modern electronics power distribution systems (EPDS). ...

  4. Development of a Commercially Viable, Modular Autonomous Robotic Systems for Converting any Vehicle to Autonomous Control

    Science.gov (United States)

    Parish, David W.; Grabbe, Robert D.; Marzwell, Neville I.

    1994-01-01

    A Modular Autonomous Robotic System (MARS), consisting of a modular autonomous vehicle control system that can be retrofit on to any vehicle to convert it to autonomous control and support a modular payload for multiple applications is being developed. The MARS design is scalable, reconfigurable, and cost effective due to the use of modern open system architecture design methodologies, including serial control bus technology to simplify system wiring and enhance scalability. The design is augmented with modular, object oriented (C++) software implementing a hierarchy of five levels of control including teleoperated, continuous guidepath following, periodic guidepath following, absolute position autonomous navigation, and relative position autonomous navigation. The present effort is focused on producing a system that is commercially viable for routine autonomous patrolling of known, semistructured environments, like environmental monitoring of chemical and petroleum refineries, exterior physical security and surveillance, perimeter patrolling, and intrafacility transport applications.

  5. Development of a Commercially Viable, Modular Autonomous Robotic Systems for Converting any Vehicle to Autonomous Control

    Science.gov (United States)

    Parish, David W.; Grabbe, Robert D.; Marzwell, Neville I.

    1994-01-01

    A Modular Autonomous Robotic System (MARS), consisting of a modular autonomous vehicle control system that can be retrofit on to any vehicle to convert it to autonomous control and support a modular payload for multiple applications is being developed. The MARS design is scalable, reconfigurable, and cost effective due to the use of modern open system architecture design methodologies, including serial control bus technology to simplify system wiring and enhance scalability. The design is augmented with modular, object oriented (C++) software implementing a hierarchy of five levels of control including teleoperated, continuous guidepath following, periodic guidepath following, absolute position autonomous navigation, and relative position autonomous navigation. The present effort is focused on producing a system that is commercially viable for routine autonomous patrolling of known, semistructured environments, like environmental monitoring of chemical and petroleum refineries, exterior physical security and surveillance, perimeter patrolling, and intrafacility transport applications.

  6. Analytical Comparison of Dual-Input Isolated dc-dc Converter with an ac or dc Inductor for Renewable Energy Systems

    DEFF Research Database (Denmark)

    Zhang, Zhe; Mira Albert, Maria del Carmen; Andersen, Michael A. E.

    2017-01-01

    This paper presents two configurations of dualinput (DI) or three-port (TPC) isolated dc-dc converters for hybrid renewable energy systems such as photovoltaics and batteries. These two converters are derived by integrating an interleaved boost converter and a single-active bridge converter...

  7. System identification of two-dimensional continuous-time systems using wavelets as modulating functions.

    Science.gov (United States)

    Sadabadi, Mahdiye Sadat; Shafiee, Masoud; Karrari, Mehdi

    2008-07-01

    In this paper, parameter identification of two-dimensional continuous-time systems via two-dimensional modulating functions is proposed. In the proposed method, trigonometric functions and sine-cosine wavelets are used as modulating functions. By this, a partial differential equation on the finite-time intervals is converted into an algebraic equation linear in parameters. The parameters of the system can then be estimated using the least square algorithms. The underlying computations utilize a two-dimensional fast Fourier transform algorithm, without the need for estimating the unknown initial or boundary conditions, at the beginning of each finite-time interval. Numerical simulations are presented to show the effectiveness of the proposed algorithm.

  8. Investigation of a matrix converter for contactless power transmission systems; Untersuchung eines Matrixumrichters fuer kontaktlose Energieuebertragungssysteme

    Energy Technology Data Exchange (ETDEWEB)

    Ecklebe, Andreas

    2009-05-22

    The publication discusses a three- to two-phase matrix converter for contactless power transmission systems. Based on relevant publications, possible resonance setups for contactless power transmission systems are investigated to begin with. An analysis of relevant parameters shows the differences between the various setups, but it also shows that for an investigation focusing on the feeding converter, simple modelling of the three investigated resonance setups is possible with the aid of a serial oscillating circuit. In consequence, it should be possible to apply the results also to the matrix converter with other serially resonant loads. The second part of the investigation focuses on the matrix converter. After a theoretical description, a combination von high-frequency control - e.g. bulk pulsing - and low-frequency pulsing patterns for setting the harmonics level of the grid currents is presented. The similarity to a conventional H bridge circuit enables an assessment of commutation and the identification of the necessary inverter states. These are characterized in that a bidirectional connection between the input system and each output phase is available at any time. The functioning of the commutation and of the inverter as a whole is proved by simulation in a first step, in which also the dynamic switching characteristics of the power semiconductors is taken into account. Finally, the results of laboratory measurements are presented and compared with the theoretical results. The laboratory setup consists of the power section of the matrix converter with input filters and modular gate drivers, a DSP/FPGA control system, and a contactless power transmission system with a current inverter and load on the secondary side. The investigation thus provides information on the use of the three-to-two phase matrix converter as an interesting alternative for feeding of contactless power transmission systems and other serially resonant loads. (orig.) [German] Diese

  9. Investigation of a matrix converter for contactless power transmission systems; Untersuchung eines Matrixumrichters fuer kontaktlose Energieuebertragungssysteme

    Energy Technology Data Exchange (ETDEWEB)

    Ecklebe, Andreas

    2009-05-22

    The publication discusses a three- to two-phase matrix converter for contactless power transmission systems. Based on relevant publications, possible resonance setups for contactless power transmission systems are investigated to begin with. An analysis of relevant parameters shows the differences between the various setups, but it also shows that for an investigation focusing on the feeding converter, simple modelling of the three investigated resonance setups is possible with the aid of a serial oscillating circuit. In consequence, it should be possible to apply the results also to the matrix converter with other serially resonant loads. The second part of the investigation focuses on the matrix converter. After a theoretical description, a combination von high-frequency control - e.g. bulk pulsing - and low-frequency pulsing patterns for setting the harmonics level of the grid currents is presented. The similarity to a conventional H bridge circuit enables an assessment of commutation and the identification of the necessary inverter states. These are characterized in that a bidirectional connection between the input system and each output phase is available at any time. The functioning of the commutation and of the inverter as a whole is proved by simulation in a first step, in which also the dynamic switching characteristics of the power semiconductors is taken into account. Finally, the results of laboratory measurements are presented and compared with the theoretical results. The laboratory setup consists of the power section of the matrix converter with input filters and modular gate drivers, a DSP/FPGA control system, and a contactless power transmission system with a current inverter and load on the secondary side. The investigation thus provides information on the use of the three-to-two phase matrix converter as an interesting alternative for feeding of contactless power transmission systems and other serially resonant loads. (orig.) [German] Diese

  10. Switching power converters medium and high power

    CERN Document Server

    Neacsu, Dorin O

    2013-01-01

    An examination of all of the multidisciplinary aspects of medium- and high-power converter systems, including basic power electronics, digital control and hardware, sensors, analog preprocessing of signals, protection devices and fault management, and pulse-width-modulation (PWM) algorithms, Switching Power Converters: Medium and High Power, Second Edition discusses the actual use of industrial technology and its related subassemblies and components, covering facets of implementation otherwise overlooked by theoretical textbooks. The updated Second Edition contains many new figures, as well as

  11. FPA Tuned Fuzzy Logic Controlled Synchronous Buck Converter for a Wave/SC Energy System

    Directory of Open Access Journals (Sweden)

    SAHIN, E.

    2017-02-01

    Full Text Available This paper presents a flower pollination algorithm (FPA tuned fuzzy logic controlled (FLC synchronous buck converter (SBC for an integrated wave/ supercapacitor (SC hybrid energy system. In order to compensate the irregular wave effects on electrical side of the wave energy converter (WEC, a SC unit charged by solar panels is connected in parallel to the WEC system and a SBC is controlled to provide more reliable and stable voltage to the DC load. In order to test the performance of the designed FLC, a classical proportional-integral-derivative (PID controller is also employed. Both of the controllers are optimized by FPA which is a pretty new optimization algorithm and a well-known optimization algorithm of which particle swarm optimization (PSO to minimize the integral of time weighted absolute error (ITAE performance index. Also, the other error-based objective functions are considered. The entire energy system and controllers are developed in Matlab/Simulink and realized experimentally. Real time applications are done through DS1104 Controller Board. The simulation and experimental results show that FPA tuned fuzzy logic controller provides lower value performance indices than conventional PID controller by reducing output voltage sags and swells of the wave/SC energy system.

  12. Dynamics of voltage source converter in a grid connected solar photovoltaic system

    DEFF Research Database (Denmark)

    Haribabu, Divyanagalakshmi; Vangari, Adithya; Sakamuri, Jayachandra N.

    2015-01-01

    This paper emphasises the modelling and control of a voltage source converter (VSC) for three phase grid connected PV system. The transfer functions for inner current control and outer DC link voltage control for VSC are derived. The controllers for VSC are designed based on PI and K factor contr...... conditions. The effectiveness of the proposed controller is illustrated by evaluating the response of PV system for power system voltage sag and swell conditions as well as grid faults.......This paper emphasises the modelling and control of a voltage source converter (VSC) for three phase grid connected PV system. The transfer functions for inner current control and outer DC link voltage control for VSC are derived. The controllers for VSC are designed based on PI and K factor control...... methods and the performance of VSC using both the methods are presented with the simulations performed using PSCAD/EMTDC. The design of LC filter to meet the specified THD requirement for grid connected VSC is presented and the corresponding harmonic analysis is performed for different solar radiation...

  13. High-sensitivity 3 to 5 micron PPLN LADAR wavelength converter system

    Science.gov (United States)

    Kingsley, S. A.; Sriram, S.; Powers, P. E.

    2005-05-01

    Remote sensing systems, such as LIDAR, have benefited greatly from nonlinear sources capable of generating tunable mid-infrared wavelengths (3-5 microns). Much work has focused on improving the energy output of these sources so as to improve the system's range. We present a different approach to improving the range by focusing on improving the receiver of a LADAR system employing nonlinear optical techniques. In this paper, we will present results of a receiver system based on frequency converting mid-infrared wavelengths to the 1.5 μm region using Periodically-Poled Lithium Niobate (PPLN). By doing so, optical amplifiers and avalanche photodetectors (APDs) developed for the fiber optics communications industry can be used, thus providing very high detection sensitivity and high speed without the need for cryogenically cooled optical detectors. We will present results of laboratory experiments with 3 μm, 2.5 ns FWHM LADAR pulses that have been converted to 1.5 μm. Detection sensitivities as low as 1.5 x 10^-13 Joules have been demonstrated. The performance of the Peltier-cooled 1.5 μm InGaAs APD quasi photon-counting receiver will be described.

  14. Dissertations Repository System Using Context Module

    CERN Document Server

    Hmood, Ali K; Alanazi, Hamdan O; Alnaqeib, Rami; Al-Nabhani, Yahya

    2010-01-01

    Without a doubt, the electronic learning makes education quite flexible. Nowadays, all organizations and institutions are trying to avoid Monotony and the delay and inertia. As well the universities should be improving their systems continually to achieve success. Whereas, the students need to access the dissertations in the library. In this paper we will present Dissertations Repository System Using Context Module to allow the students to benefit the dissertations which is in the library flexibly.

  15. DC-bus voltage control of grid-connected voltage source converter by using space vector modulated direct power control under unbalanced network conditions

    DEFF Research Database (Denmark)

    Xiao, Lei; Huang, Shoudao; Lu, Kaiyuan

    2013-01-01

    Unbalanced grid voltage will cause large dc-bus voltage ripple and introduce high harmonic current components on the grid side. This will severely threaten the safety of the grid-connected voltage source converter (VSC) and consequently, affect the healthy operation condition of the load. In this......Unbalanced grid voltage will cause large dc-bus voltage ripple and introduce high harmonic current components on the grid side. This will severely threaten the safety of the grid-connected voltage source converter (VSC) and consequently, affect the healthy operation condition of the load....... In this study, a new proportional-integral-resonant (PI-RES) controller-based, space vector modulated direct power control topology is proposed to suppress the dc-bus voltage ripple and in the same time, controlling effectively the instantaneous power of the VSC. A special ac reactive power reference component...

  16. High-feedback Operation of Power Electronic Converters

    DEFF Research Database (Denmark)

    Zhusubaliyev, Zhanybai T.; Mosekilde, Erik; Andriyanov, Alexey I.;

    2013-01-01

    The purpose of this review is to provide a survey of some of the most important bifurcation phenomena that one can observe in pulse-modulated converter systems when operating with high corrector gain factors. Like other systems with switching control, electronic converter systems belong to the cl......The purpose of this review is to provide a survey of some of the most important bifurcation phenomena that one can observe in pulse-modulated converter systems when operating with high corrector gain factors. Like other systems with switching control, electronic converter systems belong...... or resonant periodic dynamics on the surface of a two-dimensional torus. This transition occurs when the feedback gain is increased beyond a certain threshold, for instance in order to improve the speed and accuracy of the output voltage regulation. For each of the three converter types, we discuss a number...

  17. Systemic vascular resistance during brief withdrawal of angiotensin converting enzyme inhibition in heart failure

    DEFF Research Database (Denmark)

    Gabrielsen, A; Bie, P; Christensen, N J

    2002-01-01

    We tested the hypothesis that moderate increases in endogenous angiotensin II (Ang II) concentrations, induced by withdrawal of angiotensin converting enzyme inhibition (ACE-I) in patients with compensated heart failure (HF) on chronic medical therapy, do not increase or impair control of systemic...... vascular resistance (SVR). SVR was determined in supine and seated positions in 12 HF patients [NYHA class II-III; ejection fraction=0.29 +/- 0.03 (mean +/- SE)] and 9 control subjects. HF patients were investigated during high (n=11; withdrawal of ACE-I treatment for 24 h) and low (n=9; sustained ACE...

  18. Performance of a SOA-MZI wavelength converter for label swapping using combined FSK/IM modulation format

    DEFF Research Database (Denmark)

    Tafur Monroy, Idelfonso; Verdurmen, E. J. M.; Sulur, S.

    2004-01-01

    for the header/payload, respectively. Experimental results are presented for a signaling scheme with payload data at 10 Gbit/s and an FSK label at 312 Mbit/s. Simulation results and measurements of the chirp properties of converted signals operating at data rates of 2.5 and 10 Gbit/s are presented. Conclusions...

  19. Adaptive Backstepping controller design and implementation for a matrix-converter-based IM drive system

    Directory of Open Access Journals (Sweden)

    R.R. Joshi

    2007-06-01

    Full Text Available A systematic controller design and implementation for a matrix-converter-based induction motor drive system is proposed. A nonlinear adaptive backstepping controller is proposed to improve the speed and position responses of the induction motor system. By using the proposed adaptive backstepping controller, the system can track a time-varying speed command and a time-varying position command well. Moreover, the system has a good load disturbance rejection capability. The realization of the controller is very simple. All of the control loops, including the current loop, speed loop and position loop, are implemented by a digital signal processor. Several experimental results are given to validate the theoretical analysis.

  20. Small-Signal Stability of Wind Power System With Full-Load Converter Interfaced Wind Turbines

    DEFF Research Database (Denmark)

    Knüppel, Thyge; Nielsen, Jørgen Nygaard; Jensen, Kim Høj;

    2012-01-01

    Small-signal stability analysis of power system oscillations is a well established field within power system analysis, but not much attention has yet been paid to systems with a high penetration of wind turbines and with large wind power plants (WPP). In this paper a comprehensive analysis...... is presented which assesses the impact of full-load converter interfaced wind turbines on power system small-signal stability. The study is based on a 7 generator network with lightly damped inter-area modes. A detailed wind turbine (WT) model with all grid relevant control functions is used in the study....... The WT is, furthermore, equipped with a park level WPP voltage controller and comparisons are presented. The WT model for this work is a validated dynamic model of the 3.6 MW Siemens Wind Power WT. The study is based on modal analysis which is complemented with time domain simulations on the nonlinear...

  1. Comparison and Sensitivity Investigations of a CALM and SALM Type Mooring System for Wave Energy Converters

    Directory of Open Access Journals (Sweden)

    Arthur Pecher

    2014-02-01

    Full Text Available A quasi-static analysis and sensitivity investigation of two different mooring configurations—a single anchor leg mooring (SALM and a three-legged catenary anchor leg system (CALM—is presented. The analysis aims to indicate what can be expected in terms of requirements for the mooring system size and stiffness. The two mooring systems were designed for the same reference load case, corresponding to a horizontal design load at the wave energy converter (WEC of 2000 kN and a water depth of 30 m. This reference scenario seems to be representative for large WECs operating in intermediate water depths, such as Weptos, Wave Dragon and many others, including reasonable design safety factors. Around this reference scenario, the main influential parameters were modified in order to investigate their impact on the specifications of the mooring system, e.g. the water depth, the horizontal design load, and a mooring design parameter.

  2. Photovoltaic power converter system with a controller configured to actively compensate load harmonics

    Science.gov (United States)

    de Rooij, Michael Andrew; Steigerwald, Robert Louis; Delgado, Eladio Clemente

    2008-12-16

    Photovoltaic power converter system including a controller configured to reduce load harmonics is provided. The system comprises a photovoltaic array and an inverter electrically coupled to the array to generate an output current for energizing a load connected to the inverter and to a mains grid supply voltage. The system further comprises a controller including a first circuit coupled to receive a load current to measure a harmonic current in the load current. The controller includes a second circuit to generate a fundamental reference drawn by the load. The controller further includes a third circuit for combining the measured harmonic current and the fundamental reference to generate a command output signal for generating the output current for energizing the load connected to the inverter. The photovoltaic system may be configured to compensate harmonic currents that may be drawn by the load.

  3. Information processing systems, reasoning modules, and reasoning system design methods

    Energy Technology Data Exchange (ETDEWEB)

    Hohimer, Ryan E.; Greitzer, Frank L.; Hampton, Shawn D.

    2015-08-18

    Information processing systems, reasoning modules, and reasoning system design methods are described. According to one aspect, an information processing system includes working memory comprising a semantic graph which comprises a plurality of abstractions, wherein the abstractions individually include an individual which is defined according to an ontology and a reasoning system comprising a plurality of reasoning modules which are configured to process different abstractions of the semantic graph, wherein a first of the reasoning modules is configured to process a plurality of abstractions which include individuals of a first classification type of the ontology and a second of the reasoning modules is configured to process a plurality of abstractions which include individuals of a second classification type of the ontology, wherein the first and second classification types are different.

  4. Information processing systems, reasoning modules, and reasoning system design methods

    Energy Technology Data Exchange (ETDEWEB)

    Hohimer, Ryan E.; Greitzer, Frank L.; Hampton, Shawn D.

    2016-08-23

    Information processing systems, reasoning modules, and reasoning system design methods are described. According to one aspect, an information processing system includes working memory comprising a semantic graph which comprises a plurality of abstractions, wherein the abstractions individually include an individual which is defined according to an ontology and a reasoning system comprising a plurality of reasoning modules which are configured to process different abstractions of the semantic graph, wherein a first of the reasoning modules is configured to process a plurality of abstractions which include individuals of a first classification type of the ontology and a second of the reasoning modules is configured to process a plurality of abstractions which include individuals of a second classification type of the ontology, wherein the first and second classification types are different.

  5. Information processing systems, reasoning modules, and reasoning system design methods

    Science.gov (United States)

    Hohimer, Ryan E; Greitzer, Frank L; Hampton, Shawn D

    2014-03-04

    Information processing systems, reasoning modules, and reasoning system design methods are described. According to one aspect, an information processing system includes working memory comprising a semantic graph which comprises a plurality of abstractions, wherein the abstractions individually include an individual which is defined according to an ontology and a reasoning system comprising a plurality of reasoning modules which are configured to process different abstractions of the semantic graph, wherein a first of the reasoning modules is configured to process a plurality of abstractions which include individuals of a first classification type of the ontology and a second of the reasoning modules is configured to process a plurality of abstractions which include individuals of a second classification type of the ontology, wherein the first and second classification types are different.

  6. Spatial Modulation for MIMO Communication Systems

    Directory of Open Access Journals (Sweden)

    Reginaldo Nunes

    2012-11-01

    Full Text Available This work provides a review on the main spatial modulation (SM schemes, suitable to wireless communication systems. Performance, complexity and diversity gain of the three new spatial SM schemes suitable for multiple-input-multiple-output (MIMO communication systems are analyzed: a transmission scheme for spatial modulation (SM scheme; b space shift keying (SSK scheme; c generalized space shift keying (GSSK scheme. These three schemes offer low complexity, higher data rate when compared to single-input-single-output (SISO communication systems, as well as design flexibility, while exploits randomness characteristics of wireless communication channel for data transmission. The paper aims to explore the main features of those three SM schemes and to evaluate the inherent performance-complexity trade-off in order to determine which of those schemes results in a higher energy and spectral efficiencies.

  7. Test System for Thermoelectric Modules and Materials

    Science.gov (United States)

    Hejtmánek, J.; Knížek, K.; Švejda, V.; Horna, P.; Sikora, M.

    2014-10-01

    We present a design for a complex measuring device that enables its user to assess the parameters of power-generating thermoelectric modules (TEMs) (or bulk thermoelectric materials) under a wide range of temperatures ( T cold = 25°C to 90°C, T hot i) a measuring chamber where the TEM/material is compressed between thermally shielded heating blocks equipped with a mechanical loading system and water-cooled copper-based cooler, (ii) an electrical load system, (iii) a type K thermocouple array connected to a data acquisition computer, and (iv) a thermostatic water-based cooling system with electronically controlled flow rate and temperature of cooling water. Our testing setup represents a useful tool able to assess, e.g., the thermoelectric parameters of newly developed TEMs and materials or to evaluate the thermoelectric parameters of commercially available modules and materials for comparison with values declared by the manufacturer.

  8. A Different Three-Port DC/DC Converter for Standalone PV System

    Directory of Open Access Journals (Sweden)

    Nimrod Vázquez

    2014-01-01

    Full Text Available A three-port converter suitable for standalone applications is proposed in this paper. Each port is used for specific input or output, and its functions depend on the port; they are the renewable source, the battery set, and the output port. This proposed converter is considered for standalone operation, but it is not limited to it. Not only the system is able to deliver energy independently from each input source or in a mixed way for the output, but also the battery system may be charged from the renewable source just in case it is required. The battery port is only used when it is required; this allows increasing battery lifetime. Another important feature is that, in case of a renewable source failure, the energy is automatically demanded from the battery set, like an uninterruptible power supply. The system is able to track the maximum power of the renewable source when it is required. Operation, analysis, simulation, and experimental results are described in detail.

  9. High density, multi-range analog output Versa Module Europa board for control system applications

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Kundan, E-mail: kundan@iuac.res.in [Inter-University Accelerator Centre, P. O. Box 10502, New Delhi 110067 (India); Das, Ajit Lal [Netaji Subhas Institute of Technology (NSIT), New Delhi (India)

    2014-01-15

    A new VMEDAC64, 12-bit 64 channel digital-to-analog converter, a Versa Module Europa (VME) module, features 64 analog voltage outputs with user selectable multiple ranges, has been developed for control system applications at Inter University Accelerator Centre. The FPGA (Field Programmable Gate Array) is the module's core, i.e., it implements the DAC control logic and complexity of VMEbus slave interface logic. The VMEbus slave interface and DAC control logic are completely designed and implemented on a single FPGA chip to achieve high density of 64 channels in a single width VME module and will reduce the module count in the control system applications, and hence will reduce the power consumption and cost of overall system. One of our early design goals was to develop the VME interface such that it can be easily integrated with the peripheral devices and satisfy the timing specifications of VME standard. The modular design of this module reduces the amount of time required to develop other custom modules for control system. The VME slave interface is written as a single component inside FPGA which will be used as a basic building block for any VMEbus interface project. The module offers multiple output voltage ranges depending upon the requirement. The output voltage range can be reduced or expanded by writing range selection bits in the control register. The module has programmable refresh rate and by default hold capacitors in the sample and hold circuit for each channel are charged periodically every 7.040 ms (i.e., update frequency 284 Hz). Each channel has software controlled output switch which disconnects analog output from the field. The modularity in the firmware design on FPGA makes the debugging very easy. On-board DC/DC converters are incorporated for isolated power supply for the analog section of the board.

  10. High density, multi-range analog output Versa Module Europa board for control system applications.

    Science.gov (United States)

    Singh, Kundan; Das, Ajit Lal

    2014-01-01

    A new VMEDAC64, 12-bit 64 channel digital-to-analog converter, a Versa Module Europa (VME) module, features 64 analog voltage outputs with user selectable multiple ranges, has been developed for control system applications at Inter University Accelerator Centre. The FPGA (Field Programmable Gate Array) is the module's core, i.e., it implements the DAC control logic and complexity of VMEbus slave interface logic. The VMEbus slave interface and DAC control logic are completely designed and implemented on a single FPGA chip to achieve high density of 64 channels in a single width VME module and will reduce the module count in the control system applications, and hence will reduce the power consumption and cost of overall system. One of our early design goals was to develop the VME interface such that it can be easily integrated with the peripheral devices and satisfy the timing specifications of VME standard. The modular design of this module reduces the amount of time required to develop other custom modules for control system. The VME slave interface is written as a single component inside FPGA which will be used as a basic building block for any VMEbus interface project. The module offers multiple output voltage ranges depending upon the requirement. The output voltage range can be reduced or expanded by writing range selection bits in the control register. The module has programmable refresh rate and by default hold capacitors in the sample and hold circuit for each channel are charged periodically every 7.040 ms (i.e., update frequency 284 Hz). Each channel has software controlled output switch which disconnects analog output from the field. The modularity in the firmware design on FPGA makes the debugging very easy. On-board DC/DC converters are incorporated for isolated power supply for the analog section of the board.

  11. Fractional-order control and simulation of wind energy systems with PMSG/full-power converter topology

    Energy Technology Data Exchange (ETDEWEB)

    Melicio, R.; Catalao, J.P.S. [Department of Electromechanical Engineering, University of Beira Interior, R. Fonte do Lameiro, 6201-001 Covilha (Portugal); Mendes, V.M.F. [Department of Electrical Engineering and Automation, Instituto Superior de Engenharia de Lisboa, R. Conselheiro Emidio Navarro, 1950-062 Lisbon (Portugal)

    2010-06-15

    This paper presents a new integrated model for the simulation of wind energy systems. The proposed model is more realistic and accurate, considering a variable-speed wind turbine, two-mass rotor, permanent magnet synchronous generator (PMSG), different power converter topologies, and filters. Additionally, a new control strategy is proposed for the variable-speed operation of wind turbines with PMSG/full-power converter topology, based on fractional-order controllers. Comprehensive simulation studies are carried out with matrix and multilevel power converter topologies, in order to adequately assert the system performance in what regards the quality of the energy injected into the electric grid. Finally, conclusions are duly drawn. (author)

  12. Open-Switch Fault Detection Method of a Back-to-Back Converter Using NPC Topology for Wind Turbine Systems

    DEFF Research Database (Denmark)

    Lee, June-Seok; Lee, Kyo_Beum; Blaabjerg, Frede

    2015-01-01

    In wind turbine generation (WTG) systems, a back-to-back converter with a neutral-point-clamped (NPC) topology is widely used because this topology has more advantages than a conventional two-level topology, particularly when operating at high power. There are 12 switches in the NPC topology....... An open-switch fault in the NPC rectifier of the back-to-back converter leads to the distortion of the input current and torque vibration in the system. Additionally, an open-switch fault in the NPC inverter of the back-to-back converter causes the distortion of the output current. Furthermore, the WTG...

  13. A Novel Dual-input Isolated Current-Fed DC-DC Converter for Renewable Energy System

    DEFF Research Database (Denmark)

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

    2010-01-01

    In this paper, a novel isolated current-fed DC-DC converter (boost-type) with two input power sources based on multi-transformer structure, which is suitable for fuel cells and super-capacitors hybrid energy system, is proposed and designed. With particular transformer windings connection strategy......, the proposed converter can draw power from two different DC sources with lower voltage and deliver it to the higher voltage DC bus or load individually and simultaneously. The detailed operation principle of the proposed converter has been analyzed in dual-input mode and single-input mode, respectively....... Furthermore, the method to increase the number of input ports, the magnetic integration structure, and ground loop decoupling are discussed. Experimental results from the lab prototype converter with two DC voltage sources verify the validity of the theoretical analysis and design of the converter....

  14. Redundancy Protection for Sub-module Faults in Modular Multilevel Converter%模块化多电平换流器子模块故障特性和冗余保护

    Institute of Scientific and Technical Information of China (English)

    管敏渊; 徐政

    2011-01-01

    The operation mechanism of modular multilevel converter(MMC) is described.Different kinds of sub-module faults in MMC are analyzed,which may cause the oscillations of DC voltage and current and finally cause the outage of the converter.Different redundancy protection methods(RPMs) to deal with sub-module faults in cascaded H-bridge converter are compared,and then a new RPM suitable for sub-module faults in MMC is proposed.In this method,one or few redundant sub-modules are put in hot stand-by state in order to replace fault sub-module rapidly,while the others are in cold stand-by blocking state so as to protect the insulated gate bipolar translators(IGBTs) from current flowing in them.Time-domain simulation results show that the proposed RPM enables MMC based voltage source converter based high voltage direct current(VSC-HVDC) system to recover from sub-module faults without interruptions of power delivery.%对模块化多电平换流器(MMC)的基本工作原理进行了阐述,分析了MMC中子模块的几种常见故障原因,指出了单个子模块故障会引发直流电压和直流电流的振荡,最终将导致换流器停运。对级联H桥多电平换流器几种常见的子模块故障冗余保护方案进行了比较,在此基础上提出了适合MMC的子模块故障冗余保护方法。该方法将少量冗余子模块置于热备用状态,这些热备用冗余子模块能够以最快的速度接入桥臂来替换故障子模块。其余冗余子模块被置于冷备用的闭锁状态,能够可靠保护绝缘栅双极晶体管(IGBT)中没有电流流过。时域仿真结果表明,所提出的保

  15. Effect of full converter wind turbines on inter-area oscillation of power systems

    DEFF Research Database (Denmark)

    Askari, Hanieh Hajizadeh; Hashemi Toghroljerdi, Seyedmostafa; Eriksson, Robert

    2015-01-01

    turbines (FRC-WTs) on the inter-area oscillations of power system is examined. In order to have a comprehensive evaluation of the effects of FRC-WT on the inter-area oscillations, different scenarios associated with the wind power penetration levels, wind farm locations, strength of interconnection line......, and different operating conditions of synchronous generators are investigated. The synchronous generators, exciter systems and power system stabilizers (PSSs) as well as the FRC-WT grid-side converter and its related controllers are modelled in detail in Matlab in order to evaluate the effects of FRC......-WTs on the inter-area mode oscillations precisely. The results show that FRC-WTs can affect the inter-area oscillations considerably in some simulation scenarios...

  16. Grid Integration of Single Stage Solar PV System using Three-level Voltage Source Converter

    Science.gov (United States)

    Hussain, Ikhlaq; Kandpal, Maulik; Singh, Bhim

    2016-08-01

    This paper presents a single stage solar PV (photovoltaic) grid integrated power generating system using a three level voltage source converter (VSC) operating at low switching frequency of 900 Hz with robust synchronizing phase locked loop (RS-PLL) based control algorithm. To track the maximum power from solar PV array, an incremental conductance algorithm is used and this maximum power is fed to the grid via three-level VSC. The use of single stage system with three level VSC offers the advantage of low switching losses and the operation at high voltages and high power which results in enhancement of power quality in the proposed system. Simulated results validate the design and control algorithm under steady state and dynamic conditions.

  17. Design of Bidirectional Check Valve for Discrete Fluid Power Force System for Wave Energy Converters

    DEFF Research Database (Denmark)

    Hansen, Anders Hedegaard; Pedersen, Henrik C.; Andersen, Torben Ole

    2014-01-01

    Discrete fluid power force systems consisting of a multichamber cylinder, a witching manifold and common pressure lines have been proposed as a technology for increasing the efficiency of the power take off system in ocean wave energy converters. However the force shifting of these discrete systems...... enables passive force switching under minimal pressure difference, hence minimal energy loss. The bidirectional check valve is designed with a rated flow in the range of 1000L/min@5bar. The flow direction of the bidirectional check valve is set by the setting the pilot pressure. This paper presents...... a functionality test of a 125 L/min@5bar bidirectional check, leading to the design and modelling of a bidirectional check valve for ocean wave energy. It shows that a feasible bidirectional check valve may be configured by employing a multi-poppet topology for the main stage and utilising a 3/2 switching valve...

  18. Processing abstract language modulates motor system activity.

    Science.gov (United States)

    Glenberg, Arthur M; Sato, Marc; Cattaneo, Luigi; Riggio, Lucia; Palumbo, Daniele; Buccino, Giovanni

    2008-06-01

    Embodiment theory proposes that neural systems for perception and action are also engaged during language comprehension. Previous neuroimaging and neurophysiological studies have only been able to demonstrate modulation of action systems during comprehension of concrete language. We provide neurophysiological evidence for modulation of motor system activity during the comprehension of both concrete and abstract language. In Experiment 1, when the described direction of object transfer or information transfer (e.g., away from the reader to another) matched the literal direction of a hand movement used to make a response, speed of responding was faster than when the two directions mismatched (an action-sentence compatibility effect). In Experiment 2, we used single-pulse transcranial magnetic stimulation to study changes in the corticospinal motor pathways to hand muscles while reading the same sentences. Relative to sentences that do not describe transfer, there is greater modulation of activity in the hand muscles when reading sentences describing transfer of both concrete objects and abstract information. These findings are discussed in relation to the human mirror neuron system.

  19. Analysis, Design, Modelling and Control of an Interleaved-Boost Full-Bridge Three-Port Converter for Hybrid Renewable Energy Systems

    DEFF Research Database (Denmark)

    Mira Albert, Maria del Carmen; Zhang, Zhe; Knott, Arnold;

    2016-01-01

    This paper presents the design, modelling and control of a three-port (TPC) isolated dc-dc converter based on interleaved-boost-full-bridge with pulse-width-modulation and phase-shift control for hybrid renewable energy systems. In the proposed topology, the switches are driven by phase-shifted PWM...... of the proposed ac inductor based TPC is investigated by performing state-space modelling. Moreover, the derived mathematical models are validated by simulation and measurements. In order to verify the validity of the theoretical analysis, design and power decoupling control scheme, a prototype is constructed...

  20. Effect of embedded voltage source converter on power system oscillation damping

    Institute of Scientific and Technical Information of China (English)

    R; DUNN

    2010-01-01

    This paper presents the damping torque analysis of power system oscillation stability as affected by the dynamic and control functions of an embedded voltage source converter(VSC).The objective of the study is to explain why and how the dynamic and basic control functions of the embedded VSC,ac and dc voltage regulation,provide damping to power system oscillations.The most important conclusion obtained in the paper is that both the dynamics and the dc voltage control of the VSC contribute a variable damping torque,which can be positive or negative,at different levels of system load conditions.More positive damping torque can be provided by the VSC at a heavier load condition.There exists a point of system load condition where the VSC provides no damping torque to power system oscillation hence dose not impose any influence on power system oscillation stability.The VSC studied in the paper can be the power-electronics-based interface of various FACTS(flexible ac transmission systems) devices,energy storage systems and renewable power generation units,although the focus of the discussion presented in this paper is the effect of the dynamics and basic control functions of the VSC themselves on power system oscillation damping.To demonstrate the analytical conclusions obtained in the paper,results of eigenvalue computation and nonlinear simulation of an example power system with STATCOM(static synchronous compensator) are given.

  1. Space Vector Modulation for DC-Link Current Ripple Reduction in Back-To-Back Current Source Converters for Microgrid Applications

    DEFF Research Database (Denmark)

    Guo, Xiaoqiang; Xu, David; Guerrero, Josep M.

    2015-01-01

    instability. Conventionally, with a given switching frequency and rated voltage, the current ripple can be reduced by increasing the dc-link inductor, but it leads to bulky size, high cost and slow dynamic response. In order to solve this problem, this paper reveals that the current ripple can......Back-to-back converters have been typically used to interconnect the microgrids. For a back-to-back current source converter, the dc-link current ripple is one of the important parameters. A large ripple will cause the electromagnetic interference, undesirable high-frequency losses, and system...

  2. Improving Power Converter Reliability

    DEFF Research Database (Denmark)

    Ghimire, Pramod; de Vega, Angel Ruiz; Beczkowski, Szymon

    2014-01-01

    The real-time junction temperature monitoring of a high-power insulated-gate bipolar transistor (IGBT) module is important to increase the overall reliability of power converters for industrial applications. This article proposes a new method to measure the on-state collector?emitter voltage...... of a high-power IGBT module during converter operation, which may play a vital role in improving the reliability of the power converters. The measured voltage is used to estimate the module average junction temperature of the high and low-voltage side of a half-bridge IGBT separately in every fundamental...... is measured in a wind power converter at a low fundamental frequency. To illustrate more, the test method as well as the performance of the measurement circuit are also presented. This measurement is also useful to indicate failure mechanisms such as bond wire lift-off and solder layer degradation...

  3. Multi-functional Converter with Integrated Motor Control, Battery Charging and Active Module Balancing for Electric Vehicular Application

    DEFF Research Database (Denmark)

    Mathe, Laszlo; Schaltz, Erik; Teodorescu, Remus

    2014-01-01

    , weight and volume in comparison with other Li-Ion based chemistries. The control of the energy flow has been done through a Modular Multilevel Converter (MMC), which has demonstrated advantages over 2 level converters in terms of efficiency, fault tolerant operation, flexible operation modes. It has been......In order to reduce the fuel consumption and the acoustical noise generated by refuse lorries, electrification of the waste compactor unit is a very promising solution. For the electrical energy storage Lithium-Sulfur (Li-S) battery technology has been selected with potential for reducing the cost...... used successfully in HVDC/FACTS and large drive applications. In this paper the use of MMC for a battery driven waste compactor unit addressed with integrated functionality including: motor driver, battery charge and active balancing is presented. The challenges addressed here are related to the design...

  4. Multichannel analog-to-digital converters based on current mirrors for the optical systems

    Science.gov (United States)

    Krasilenko, Vladimir G.; Nikolskyy, A. I.; Nikolska, M. A.; Lobodzinska, R. F.

    2011-12-01

    The paper considers results of designing and modeling analogue-digital converters (ADC) based on current mirrors for the optical systems and neural networks with parallel inputs-outputs. Such ADC, named us multichannel analog-todigital converters based on current mirrors (M ADC CM). Compared with usual converters, for example, reading, a bitby- bit equilibration, and so forth, have a number of advantages: high speed and reliability, simplicity, small power consumption, the big degree of integration in linear and matrix structures. The considered aspects of designing of M_ADC CM in binary codes. Base digit cells (ABC) of such M_ADC CM, series-pipelined are connected in structures, consist from 20-30 CMOS the transistors, one photodiode, have low (1,5-3,5) supply voltage, work in current modes with the maximum values of currents (10-40)μA. Therefore such new principles of realization high-speed low-discharge M_ADC CM have allowed, as have shown modeling experiments, to reach time of transformation less than 20-30 nS at 5-6 bits of a binary code and the general power 1-5 mW. The quantity easily cascadable ABC depends on wordlength ADC, and makes n, and provides quantity of levels of quantization equal N=2n. Such simple enough on structure M ADC CM, having low power consumption CMOS-technologies has made 40 MHz, and can be increased 10 times) and accuracy (Δquantization 156,25nA for I max10μA) characteristics is show. The range can be transformed optical signals, taking into account sensitivity of modern photodetectors makes 20-200 μW in such ADC. M_ADC CM open new prospects for realization linear and matrix (with picture operands) micro photoelectronic structures which are necessary for neural networks, digital optoelectronic processors, neurofuzzy controllers, and so forth.

  5. Analysis of Pulse Modulated Control Systems (Ⅲ) Stability of Systems with Pulse Frequency Modulation and Systems with Combined Pulse Frequency and Pulse Width Modulation

    OpenAIRE

    OI,Shigemitsu

    1993-01-01

    Sufficient conditions for finite pulse stability of interconnected systems with combined pulse frequency and pulse width modulation are developed in this paper using a direct method. The stability criteria established provide upper bounds on the number of pulses emitted by each modulator. The results are also applicable to those systems which contain a finite number of pulse frequency modulators and a finite number of combined pulse frequency and pulse width modulators

  6. Radiation tolerant power converter controls

    Science.gov (United States)

    Todd, B.; Dinius, A.; King, Q.; Uznanski, S.

    2012-11-01

    The Large Hadron Collider (LHC) at the European Organisation for Nuclear Research (CERN) is the world's most powerful particle collider. The LHC has several thousand magnets, both warm and super-conducting, which are supplied with current by power converters. Each converter is controlled by a purpose-built electronic module called a Function Generator Controller (FGC). The FGC allows remote control of the power converter and forms the central part of a closed-loop control system where the power converter voltage is set, based on the converter output current and magnet-circuit characteristics. Some power converters and FGCs are located in areas which are exposed to beam-induced radiation. There are numerous radiation induced effects, some of which lead to a loss of control of the power converter, having a direct impact upon the accelerator's availability. Following the first long shut down (LS1), the LHC will be able to run with higher intensity beams and higher beam energy. This is expected to lead to significantly increased radiation induced effects in materials close to the accelerator, including the FGC. Recent radiation tests indicate that the current FGC would not be sufficiently reliable. A so-called FGClite is being designed to work reliably in the radiation environment in the post-LS1 era. This paper outlines the concepts of power converter controls for machines such as the LHC, introduces the risks related to radiation and a radiation tolerant project flow. The FGClite is then described, with its key concepts and challenges: aiming for high reliability in a radiation field.

  7. Power Converters for Accelerators

    CERN Document Server

    Visintini, R

    2015-01-01

    Particle accelerators use a great variety of power converters for energizing their sub-systems; while the total number of power converters usually depends on the size of the accelerator or combination of accelerators (including the experimental setup), the characteristics of power converters depend on their loads and on the particle physics requirements: this paper aims to provide an overview of the magnet power converters in use in several facilities worldwide.

  8. A Novel Dual-input Isolated Current-Fed DC-DC Converter for Renewable Energy System

    DEFF Research Database (Denmark)

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

    2010-01-01

    In this paper, a novel isolated current-fed DC-DC converter (boost-type) with two input power sources based on multi-transformer structure, which is suitable for fuel cells and super-capacitors hybrid energy system, is proposed and designed. With particular transformer windings connection strategy......, the proposed converter can draw power from two different DC sources with lower voltage and deliver it to the higher voltage DC bus or load individually and simultaneously. The detailed operation principle of the proposed converter has been analyzed in dual-input mode and single-input mode, respectively...

  9. A Modular PV System Using Chain-Link-Type Multilevel Converter

    Science.gov (United States)

    Hatano, Nobuhiko; Ise, Toshifumi

    This paper presents a modular photovoltaic system (MPVS) that uses a chain-link-type multilevel converter (CLMC). In large-scale PV generating systems, the DC power supply is generally composed of a large number of PV panels. Hence, losses are caused by differences in the maximum power point at each PV panel. An MPVS has been proposed to address the above mentioned problem. It helps improve the photoelectric conversion efficiency by applying maximum power point tracking (MPPT) control to each group of PV panels. In addition, if a CLMC is used in an MPVS, a high voltage can be output from the AC side and transmission losses can be decreased. However, with this circuit configuration, the current output from the AC side may be unbalanced. Therefore, we propose a method to output balanced current from the AC side, even if the output of the DC power supply is unbalanced. The validity of the proposed method is examined by digital simulation.

  10. Effects of Mooring Systems on the Performance of a Wave Activated Body Energy Converter

    DEFF Research Database (Denmark)

    Zanuttigh, Barbara; Angelelli, Elisa; Kofoed, Jens Peter

    2013-01-01

    Aim of this paper is to analyse the power and hydraulic performance of a floating Wave Energy Converter with the purpose at optimising its design for installation in arrays. The paper presents new experiments carried out in 1:30 scale on a single device of the Wave Activated Body type in the deep......-water wave tank at Aalborg University. Power production and wave transmission were examined by changing the mooring system, the wave attack and the device orientation with respect to the incoming waves.. To assure the best performance the device size may be “tuned” based on the local peak wave length...... and the mooring system should be selected to allow the device for large movements....

  11. Photovoltaic Power System with an Interleaving Boost Converter for Battery Charger Applications

    Directory of Open Access Journals (Sweden)

    Sheng-Yu Tseng

    2012-01-01

    Full Text Available This paper proposes a photovoltaic (PV power system for battery charger applications. The charger uses an interleaving boost converter with a single-capacitor turn-off snubber to reduce voltage stresses of active switches at turn-off transition. Therefore, active switches of the charger can be operated with zero-voltage transition (ZVT to decrease switching losses and increase conversion efficiency. In order to draw the maximum power from PV arrays and obtain the optimal power control of the battery charger, a perturbation-and-observation method and microchip are incorporated to implement maximum power point tracking (MPPT algorithm and power management. Finally, a prototype battery charger is built and implemented. Experimental results have verified the performance and feasibility of the proposed PV power system for battery charger applications.

  12. Optimized Controller Design for a 12-Pulse Voltage Source Converter Based HVDC System

    Science.gov (United States)

    Agarwal, Ruchi; Singh, Sanjeev

    2017-08-01

    The paper proposes an optimized controller design scheme for power quality improvement in 12-pulse voltage source converter based high voltage direct current system. The proposed scheme is hybrid combination of golden section search and successive linear search method. The paper aims at reduction of current sensor and optimization of controller. The voltage and current controller parameters are selected for optimization due to its impact on power quality. The proposed algorithm for controller optimizes the objective function which is composed of current harmonic distortion, power factor, and DC voltage ripples. The detailed designs and modeling of the complete system are discussed and its simulation is carried out in MATLAB-Simulink environment. The obtained results are presented to demonstrate the effectiveness of the proposed scheme under different transient conditions such as load perturbation, non-linear load condition, voltage sag condition, and tapped load fault under one phase open condition at both points-of-common coupling.

  13. STUDIES ON IGBT MODULE TO IMPROVE THE RELIABILITY OF POWER ELECTRONIC SYSTEMS

    DEFF Research Database (Denmark)

    Choi, Uimin

    As power electronic systems have gradually gained an important status in a wide range of industrial applications, there are increasing demands to improve the reliability and robustness of power electronic systems. The power electronic systems consist of various components, and among them, power...... that kills IGBT modules. Therefore, in order to improve the reliability of power electronic systems, reliability research on reliability-critical components regarding the major critical stressors are needed. In this PhD project, various researches on reliability of the IGBT module are performed from...... component level to converter level. It is divided into two main parts: the first part, which consists of Chapters 2 and 3, is reliability studies of the IGBT module regarding thermal stresses and the second part, composed of Chapters 4 and 5, discusses strategies to improve the reliability and availability...

  14. A Simple MPPT Algorithm for Novel PV Power Generation System by High Output Voltage DC-DC Boost Converter

    DEFF Research Database (Denmark)

    Sanjeevikumar, Padmanaban; Grandi, Gabriele; Wheeler, Patrick

    2015-01-01

    This paper presents the novel topology of Photo Voltaic (PV) power generation system with simple Maximum Power Point Tracking (MPPT) algorithm in voltage operating mode. Power circuit consists of high output voltage DC-DC boost converter which maximizes the output of PV panel. Usually traditional...... of DC-DC converters for PV integration. Hence, to overcome these difficulties this paper investigates a DC-DC boost converter together with the additional parasitic component within the circuit to provide high output voltages for maximizing the PV power generation. The proposed power system circuit...... substantially improves the high output-voltage by a simple MPPT closed loop proportional-integral (P-I) controller, and requires only two sensor for feedback needs. The complete numerical model of the converter circuit along with PV MPPT algorithm is developed in numerical simulation (Matlab/Simulink) software...

  15. System and method for design and optimization of grid connected photovoltaic power plant with multiple photovoltaic module technologies

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, Bex George; Elasser, Ahmed; Bollapragada, Srinivas; Galbraith, Anthony William; Agamy, Mohammed; Garifullin, Maxim Valeryevich

    2016-03-29

    A system and method of using one or more DC-DC/DC-AC converters and/or alternative devices allows strings of multiple module technologies to coexist within the same PV power plant. A computing (optimization) framework estimates the percentage allocation of PV power plant capacity to selected PV module technologies. The framework and its supporting components considers irradiation, temperature, spectral profiles, cost and other practical constraints to achieve the lowest levelized cost of electricity, maximum output and minimum system cost. The system and method can function using any device enabling distributed maximum power point tracking at the module, string or combiner level.

  16. Design and Implementation of Power Converters for Hybrid Wind-Solar Energy Conversion System with an Implementation of MPPT

    Directory of Open Access Journals (Sweden)

    G. Sridhar Babu

    2013-11-01

    Full Text Available This paper presents the design and implementation of power converters for wind conversion systems. The power converter can not only transfer the power from a wind generator, but also improve the stability and safety of the system. The proposed system consists of a Permanent magnet synchronous generator (PMSG; a DC/DC boosts converter, a bi-directional DC/DC converter and a full-bridge DC/AC inverter. The wind generator is the main power source of the system, and the battery is used for energy storage and power compensation to recover the natural irregularity of the wind power. In this paper presents a new system configuration of the front-end rectifier stage for a hybrid wind or photo voltaic energy system. The configuration allows the two sources to supply the load separately or simultaneously, depending on the availability of energy sources. The inherent nature of this cuk-scpic fused converter, additional input filters are not necessary to filter out high frequency harmonic content is determinant for the generator life span, heating issue and efficiency. The fused multi-input rectifier stage also allows maximum power from the wind and sun. When it is available an adaptive MPPT algorithm will be used for photo voltaic (PV system. Operational analysis of the roposed system, will discoursed in this paper simulation results are given to highlight the merit of the proposed circuit.

  17. Dynamics and Control of Switched Electronic Systems Advanced Perspectives for Modeling, Simulation and Control of Power Converters

    CERN Document Server

    Iannelli, Luigi

    2012-01-01

    The increased efficiency and quality constraints imposed on electrical energy systems have inspired a renewed research interest in the study of formal approaches to the analysis and control of power electronics converters. Switched systems represent a useful framework for modeling these converters and the peculiarities of their operating conditions and control goals justify the specific classification of “switched electronic systems”. Indeed, idealized switched models of power converters introduce problems not commonly encountered when analyzing generic switched models or non-switched electrical networks. In that sense the analysis of switched electronic systems represents a source for new ideas and benchmarks for switched and hybrid systems generally. Dynamics and Control of Switched Electronic Systems draws on the expertise of an international group of expert contributors to give an overview of recent advances in the modeling, simulation and control of switched electronic systems. The reader is provided...

  18. A SYSTEM TO MAKE USE OF EXISTING BREAKWATERS AS OVERTOPPING WAVE ENERGY CONVERTERS

    Directory of Open Access Journals (Sweden)

    DENIZ ÜNSALAN

    2016-06-01

    Full Text Available The main purpose of building breakwaters is to produce safe havens for ships and boats in rough seas. The general architecture for a breakwater is a wall with a trapezoidal -shaped cross section extending parallel to the shoreline. As the waves from the open sea approach, they are encountered by the so- called slope and revetment of the breakwater, where the wave is broken and its energy is dissipated and/or reflected back. However, the ever -increasing attractiveness of the utilization of waves as energy sources, paralleling to the increasing monetary and envir onmental costs of energy, has led the authors to consider the vast amounts of this otherwise dissipated energy into useful electrical energy. A wave energy conversion concept, which can be classified as an “overtopping” wave energy converter was conceived, where the open sea-facing (revetment side of the breakwater is fitted by a water collecting channel at a suitable height above the calm water level, running alongside the breakwater. The channel leads the collected water to a powerhouse containing a low head turbine (or a set of such turbines discharging it to the calm water of the inner harbour. Power obtained from these turbines can be converted to electrical energy. In this study, an estimation of the volume of water collected by the channel and the energy production for a proposed breakwater - power station system for a typical rough weather shall be made. It is deemed that the feasibility of this system is comparable to and even higher than the other wave energy conversion systems since it does not require additional facilities and power supply lines to be built due to its proximity to the existing energy transmission lines, except for the addition of new features/installations to the existing breakwaters.

  19. Phase-modulation transmission system for quantum cryptography.

    Science.gov (United States)

    Mérolla, J M; Mazurenko, Y; Goedgebuer, J P; Porte, H; Rhodes, W T

    1999-01-15

    We describe a new method for quantum key distribution that utilizes phase modulation of sidebands of modulation by use of integrated electro-optic modulators at the transmitting and receiving modules. The system is shown to produce constructive or destructive interference with unity visibility, which should allow quantum cryptography to be carried out with high flexibility by use of conventional devices.

  20. A PWM Buck Converter With Load-Adaptive Power Transistor Scaling Scheme Using Analog-Digital Hybrid Control for High Energy Efficiency in Implantable Biomedical Systems.

    Science.gov (United States)

    Park, Sung-Yun; Cho, Jihyun; Lee, Kyuseok; Yoon, Euisik

    2015-12-01

    We report a pulse width modulation (PWM) buck converter that is able to achieve a power conversion efficiency (PCE) of > 80% in light loads 100 μA) for implantable biomedical systems. In order to achieve a high PCE for the given light loads, the buck converter adaptively reconfigures the size of power PMOS and NMOS transistors and their gate drivers in accordance with load currents, while operating at a fixed frequency of 1 MHz. The buck converter employs the analog-digital hybrid control scheme for coarse/fine adjustment of power transistors. The coarse digital control generates an approximate duty cycle necessary for driving a given load and selects an appropriate width of power transistors to minimize redundant power dissipation. The fine analog control provides the final tuning of the duty cycle to compensate for the error from the coarse digital control. The mode switching between the analog and digital controls is accomplished by a mode arbiter which estimates the average of duty cycles for the given load condition from limit cycle oscillations (LCO) induced by coarse adjustment. The fabricated buck converter achieved a peak efficiency of 86.3% at 1.4 mA and > 80% efficiency for a wide range of load conditions from 45 μA to 4.1 mA, while generating 1 V output from 2.5-3.3 V supply. The converter occupies 0.375 mm(2) in 0.18 μm CMOS processes and requires two external components: 1.2 μF capacitor and 6.8 μH inductor.

  1. [An integral chip for the multiphase pulse-duration modulation used for voltage changer in biomedical microprocessor systems].

    Science.gov (United States)

    Balashov, A M; Selishchev, S V

    2004-01-01

    An integral chip (IC) was designed for controlling the step-down pulse voltage converter, which is based on the multiphase pulse-duration modulation, for use in biomedical microprocessor systems. The CMOS technology was an optimal basis for the IC designing. An additional feedback circuit diminishes the output voltage dispersion at dynamically changing loads.

  2. Modular VSC converter based HVDC power transmission from offshore wind power plant: Compared to the conventional HVAC system

    DEFF Research Database (Denmark)

    Sharma, Ranjan; Rasmussen, Tonny Wederberg; Jensen, Kim Høj;

    2010-01-01

    power transmission options with HVDC systems are under consideration. In this paper, a comparison between a conventional HVAC transmission system and a HVDC system equipped with modular voltage source converters is provided. The comparison is based on the total energy transmission capability...

  3. An oscillating wave energy converter with nonlinear snap-through Power-Take-Off systems in regular waves

    Science.gov (United States)

    Zhang, Xian-tao; Yang, Jian-min; Xiao, Long-fei

    2016-07-01

    Floating oscillating bodies constitute a large class of wave energy converters, especially for offshore deployment. Usually the Power-Take-Off (PTO) system is a directly linear electric generator or a hydraulic motor that drives an electric generator. The PTO system is simplified as a linear spring and a linear damper. However the conversion is less powerful with wave periods off resonance. Thus, a nonlinear snap-through mechanism with two symmetrically oblique springs and a linear damper is applied in the PTO system. The nonlinear snap-through mechanism is characteristics of negative stiffness and double-well potential. An important nonlinear parameter γ is defined as the ratio of half of the horizontal distance between the two springs to the original length of both springs. Time domain method is applied to the dynamics of wave energy converter in regular waves. And the state space model is used to replace the convolution terms in the time domain equation. The results show that the energy harvested by the nonlinear PTO system is larger than that by linear system for low frequency input. While the power captured by nonlinear converters is slightly smaller than that by linear converters for high frequency input. The wave amplitude, damping coefficient of PTO systems and the nonlinear parameter γ affect power capture performance of nonlinear converters. The oscillation of nonlinear wave energy converters may be local or periodically inter well for certain values of the incident wave frequency and the nonlinear parameter γ, which is different from linear converters characteristics of sinusoidal response in regular waves.

  4. A novel implementation of mARC treatment for non-dedicated planning systems using converted IMRT plans.

    Science.gov (United States)

    Dzierma, Yvonne; Nuesken, Frank; Licht, Norbert; Ruebe, Christian

    2013-08-03

    The modulated arc (mARC) technique has recently been introduced by Siemens as an analogue to VMAT treatment. However, up to now only one certified treatment planning system supports mARC planning. We therefore present a conversion algorithm capable of converting IMRT plans created by any treatment planning system into mARC plans, with the hope of expanding the availability of mARC to a larger range of clinical users and researchers. As additional advantages, our implementation offers improved functionality for planning hybrid arcs and provides an equivalent step-and-shoot plan for each mARC plan, which can be used as a back-up concept in institutions where only one linac is equipped with mARC. We present a feasibility study to outline a practical implementation of mARC plan conversion using Philips Pinnacle and Prowess Panther. We present examples for three different kinds of prostate and head-and-neck plans, for 6 MV and flattening-filter-free (FFF) 7 MV photon energies, which are dosimetrically verified. It is generally more difficult to create good quality IMRT plans in Pinnacle using a large number of beams and few segments. We present different ways of optimization as examples. By careful choosing the beam and segment arrangement and inversion objectives, we achieve plan qualities similar to our usual IMRT plans. The conversion of the plans to mARC format yields functional plans, which can be irradiated without incidences. Absolute dosimetric verification of both the step-and-shoot and mARC plans by point dose measurements showed deviations below 5% local dose, mARC plans deviated from step-and-shoot plans by no more than 1%. The agreement between GafChromic film measurements of planar dose before and after mARC conversion is excellent. The comparison of the 3D dose distribution measured by PTW Octavius 729 2D-Array with the step-and-shoot plans and with the TPS is well above the pass criteria of 90% of the points falling within 5% local dose and 3

  5. A tapped-inductor buck-boost converter for a multi-DEAP generator energy harvesting system

    DEFF Research Database (Denmark)

    Dimopoulos, Emmanouil; Munk-Nielsen, Stig

    2014-01-01

    the effective operational range of the power electronic converter. In this paper, a bidirectional tapped-inductor buck-boost converter is proposed, addressing high-efficient high step-up and high step-down voltage conversion ratios, for energy harvesting applications based on DEAP generators. The effective...... operational range of the converter is extended, by replacing its high-side switch with a string of three serialized MOSFETs, to accommodate the need for high-efficient high-voltage operation. Experiments conducted on a single DEAP generator - part of a quadruple DEAP generator energy harvesting system...... with all elements installed sequentially in the same circular disk with a 90 phase shift - validate the applicability of the proposed converter, demonstrating energy harvesting of 0.26 J, at 0.5 Hz and 60 % delta-strain; characterized by an energy density of 1.25 J per kg of active material....

  6. Design of DC-DC Converter and its Control for a Wind Generation System Connected to an Isolated Load

    Directory of Open Access Journals (Sweden)

    Carlos A. Ramírez Gómez

    2013-11-01

    Full Text Available A method to design a Buck converter and its control, which are associated to a wind generation system that is feeding an isolated load, is presented in this paper. To design the converter a Thevenin equivalent is deduced, which represents the behavior of the wind turbine, the permanent magnet synchronous generator, and the rectifier. The design of the converter elements guarantees input/output voltages and inductor current ripples of 5 % or less. The output voltage control is developed with a proportional-integral-derivative controller and as design criteria a damping of 0,707 and cutoff frequency of 1/5 converter commutation frequency are selected. The designed controller regulates the output voltage faced load perturbations and wind speed variations. 

  7. Modular Multi-level converter based HVDC System for Grid Connection of Offshore Wind Power Plant

    DEFF Research Database (Denmark)

    Gnanarathna, U.N.; Chaudhary, Sanjay Kumar; Gole, A.M.;

    2010-01-01

    This paper explores the application of modular multi-level converters (MMC) as a means for harnessing the power from off-shore wind power plants. The MMC consists of a large number of simple voltage sourced converter (VSC) submodules that can be easily assembled into a converter for high......-voltage and high power. The paper shows that the MMC converter has a fast response and low harmonic content in comparison with a two-level VSC option. The paper discusses the modeling approach used, including a solution to the modeling challenge imposed by the very large number of switching devices in the MMC....

  8. A bi-directional DC/DC converter for hybrid wind generator/battery system with state machine control

    Energy Technology Data Exchange (ETDEWEB)

    Hua, C.C.; Liao, Y.C. [National Yunlin Univ. of Science and Technology, Yunlin, Taiwan (China). Dept. of Electrical Engineering

    2008-07-01

    A bi-directional DC to DC converter used in a hybrid wind generator/lead-acid battery power system was presented. A state machine control strategy was used to control both the system power flow and load distribution. It was also used to increase the power capacity of the system. The battery was also charged or discharged through the bi-directional DC to DC converter. Multi-stage current charging control of the batteries was accomplished by adjusting the duty cycle of the power converter. This also improved the charging efficiency by the maximum power point tracking algorithm. It was concluded that the proposed control method can be readily extended to other renewable energy conversion systems. 6 refs., 13 figs.

  9. Modulation of anxiety circuits by serotonergic systems

    DEFF Research Database (Denmark)

    Lowry, Christopher A; Johnson, Philip L; Hay-Schmidt, Anders

    2005-01-01

    Anxiety is a complex emotional state associated with sustained heightened autonomic and behavioral arousal and an increase in avoidance behavior. Anxiety-related behavior is a form of risk assessment behavior that is associated with a level of uncertainty or unpredictability regarding the outcome...... of emotionally salient events, often when both rewarding and aversive outcomes are possible. In this review, we highlight recent advances in our understanding of the neural circuits regulating anxiety states and anxiety-related behavior with an emphasis on the role of brainstem serotonergic systems in modulating...... anxiety-related circuits. In particular, we explore the possibility that the regulation of anxiety states and anxiety-related behavior by serotonergic systems is dependent on a specific, topographically organized mesolimbocortical serotonergic system that originates in the mid-rostrocaudal and caudal...

  10. A photonic analog-to-digital converter using phase modulation and self-coherent detection with spatial oversampling.

    Science.gov (United States)

    Golani, Ori; Mauri, Luca; Pasinato, Fabiano; Cattaneo, Cristian; Consonnni, Guido; Balsamo, Stefano; Marom, Dan M

    2014-05-19

    We propose a new type of photonic analog-to-digital converter (ADC), designed for high-resolution (>7 bit) and high sampling rates (scalable to tens of GS/s). It is based on encoding the input analog voltage signal onto the phase of an optical pulse stream originating from a mode-locked laser, and uses spatial oversampling as a means to improve the conversion resolution. This paper describes the concept of spatial oversampling and draws its similarities to the commonly used temporal oversampling. The design and fabrication of a LiNbO(3)/silica hybrid photonic integrated circuit for implementing the spatial oversampling is shown, and its abilities are demonstrated experimentally by digitizing gigahertz signals (frequencies up to 18GHz) at an undersampled rate of 2.56GS/s with a conversion resolution of up to 7.6 effective bits. Oversampling factors of 1-4 are demonstrated.

  11. Teller Training Module: Off-Line Banking System. High-Technology Training Module.

    Science.gov (United States)

    Lund, Candyce J.

    This teller training module on offline banking systems is intended to be part of a postsecondary financial applications course. The module contains the following sections: module objective; specific objective; content--electronic audit machine key functions, practice packet--sample bank transactions and practicing procedures, and…

  12. A variable step-down conversion ratio switched capacitor DC-DC converter for energy harvesting systems working in intermittent mode

    Energy Technology Data Exchange (ETDEWEB)

    Hao Wenhan; Jia Chen; Chen Hong; Zhang Chun; Wang Zhihua, E-mail: haowh04@mails.tsinghua.edu.c [Tsinghua National Laboratory for Information Science and Technology, Institute of Microelectronics, Tsinghua University, Beijing 100084 (China)

    2009-12-15

    Energy harvesting systems stimulate the development of power management for low power consumption applications. Improving the converter efficiency of power management circuits has become a significant issue in energy harvesting system design. This paper presents a variable step-down conversion ratio switched capacitor (SC) DC-DC converter to advance the converter efficiency of charge on the stored capacitor in a wireless monitoring system of orthopedic implants. The converter is designed to work at 1 MHz switching frequency and achieves 15 to 2 V conversion. Measurement results show that the converter efficiency can reach 42% including all circuit power consumption, which is much higher than previous work. (semiconductor integrated circuits)

  13. A variable step-down conversion ratio switched capacitor DC-DC converter for energy harvesting systems working in intermittent mode

    Institute of Scientific and Technical Information of China (English)

    Hao Wenhan; Jia Chen; Chen Hong; Zhang Chun; Wang Zhihua

    2009-01-01

    Energy harvesting systems stimulate the development of power management for low power consumption applications. Improving the converter efficiency of power management circuits has become a significant issue in energy harvesting system design. This paper presents a variable step-down conversion ratio switched capacitor (SC)DC-DC converter to advance the converter efficiency of charge on the stored capacitor in a wireless monitoring system of orthopedic implants. The converter is designed to work at 1 MHz switching frequency and achieves 15 to 2 V conversion. Measurement results show that the converter efficiency can reach 4:2% including all circuit power consumption, which is much higher than previous work.

  14. Three-port DC-DC converter with new integrated transformer for DC Distribution Systems

    DEFF Research Database (Denmark)

    Ouyang, Ziwei; Andersen, Michael A. E.

    2014-01-01

    A new integrated transformer for three-port dc-dc converter is proposed to overcome the power coupling effect existed in some known multiple inputs dc-dc converters. Orthogonal primary windings arrangement and in series connection of diagonal secondary Windings enables a fully power decoupling...

  15. Modelling, Simulation and Construction of a DC/DC Boost Power Converter: A School Experimental System

    Science.gov (United States)

    Silva-Ortigoza, R.; Silva-Ortigoza, G.; Hernandez-Guzman, V. M.; Saldana-Gonzalez, G.; Marcelino-Aranda, M.; Marciano-Melchor, M.

    2012-01-01

    We introduce a dc/dc boost power converter as a didactic prototype intended to support courses on electric circuit analysis experimentally. The corresponding mathematical model is obtained, the converter is designed and an experimental setup is described, constructed and tested. Simplicity of construction as well as low cost of components renders…

  16. SiC-based High Efficiency Bidirectional Battery Converter for Smart PV Residential Systems

    DEFF Research Database (Denmark)

    Pham, Cam; Biris, Valeriu-Ciprian; Teodorescu, Remus;

    2013-01-01

    -DC converter for the battery storage is necessary, as energy will be processed twice. Realisation of the battery converter with silicon carbide (SiC) semiconductors offers many advantages compared to Silicon (Si), included higher power density and higher efficiency. In this paper the design of a simple high...

  17. Vector Modulator for Phase Shifting in Passive Beamforming Wireless Systems

    Directory of Open Access Journals (Sweden)

    P.Sampath,

    2010-05-01

    Full Text Available This paper proposes vector modulator for changing the phase of a signal in passive beamforming system. Vector modulator is used to perform a phase shift function with added benefit of amplitude control. It is used to improve the directivity of RF waves in Wireless systems. Vector modulator is implemented for a center frequency of 902.5 MHz. The simulation is performed for individual blocks of the vector modulator and for vector modulator with JFET and MOSFET as controlling device in the variable attenuator of the vector modulator.

  18. IMITATING THE MODEL OF THE FREQUENCY CONVERTER - INDUCTION MOTOR OF A PUMP WATER SYSTEM WITH ADAPTIVE CONTROL ALGORITHM

    Directory of Open Access Journals (Sweden)

    Taranov D. M.

    2015-06-01

    Full Text Available This article presents main water supply systems and justifies the choice of direct flow of water supply system in the application of regulation of electric drive for pumps, which doesn’t have any tanks to create pressures required for fire-governmental purposes. This avoids interruption in the supply of reserve while water freezing. In the article the substantiation of the necessity of implementation of adaptive algorithm in modern-WIDE frequency converters by a substantiation of the number of stages of ratio control of voltage-frequency mains. It was revealed that the number of degrees of regulation of 10-12 gives optimum. Modern frequency converters allow you to change the regulation law, establishing 3-5 points of regulation. Therefore, the introduction of adaptive algorithm will reduce the power consumption of the electric drive of the pump of the water supply system. The article shows the simulation model of the "the converter frequency-induction motor," plots of the stator current of mains frequency and active power, surface speed and phase current when changing the voltage and frequency of the mains. These dependences confirm to have applicability of adaptive algorithm in the regulation of modern frequency converters with the skalar administration. Simulation model confirms the sub-physical experiments on a real motor and frequency converter with adaptive control algorithm. As a result of the selection of the parameters, we obtain the voltage reduction of the phase current, and reduce electricity consumption by 5-7%

  19. Transient analysis and control of bias magnetic state in the transformer of on-line pulse-width-modulation switching full bridge direct current-direct current converter

    Science.gov (United States)

    Chen, Jiaxin; Guo, Youguang; Zhu, Jianguo; Wei Lin, Zhi

    2012-04-01

    This paper presents a finite element analysis (FEA) based method for analyzing and controlling the bias magnetic state of the transformer of a pulse-width-modulation (PWM) switching full bridge dc-dc converter. A field-circuit indirect coupling method for predicting the transient bias magnetic state is introduced first. To increase flexibility of the proposed method, a novel transformer model which can address not only its basic input-output characteristic, but also the nonlinear magnetizing inductance, is proposed. Both the asymmetric characteristic and the variable laws of the current flowing through the two secondary windings during the period of PWM switching-off state are highlighted. Finally, the peak magnetizing current controlled method based on the on-line magnetizing current computation is introduced. Analysis results show that this method can address the magnetic saturation at winding ends, and hence many previous difficulties, such as the start-up process and asymmetry of power electronics, can be easily controlled.

  20. Novel Modulation Scheme Research of Modular Multilevel Converter%一种新型模块化多电平换流器调制策略研究

    Institute of Scientific and Technical Information of China (English)

    谭玉茹; 苏建徽

    2012-01-01

    介绍了适用于轻型直流输电系统(VSC - HVDC)的模块化多电平换流器(MMC)拓扑结构及原理,并提出一种适用于MMC的新型移相载波调制策略(CPS - SPWM).基于MMC的能量均衡和电压平衡问题,还提出了和调制策略相协调的电容电压均衡控制方法,最后通过Matlab/Simulink搭建了MMC仿真模型,结果证明所提出的控制方法可以有效地平衡换流器子模块的电容电压,并且保证MMC外部输出良好的交流电压和电流.%The principle and topology of modular multilevel converter (MMC) were proposed, which is a new multilevel converter suitable for VSC - HVDC. A novel carried phase shifted sinusoidal pulse width modulation (CPS - SPWM) scheme suitable for MMC in VSC - HVDC was presented. Based on the energy equipar-tition and voltage balance,a capacitor voltage-balancing strategy was presented with the topology of MMC and modulation. Simulation results based on Matlab/Simulink show that the control method can balance the capacitance voltage of submodule. It is also shown that it can ensure good AC voltage and current of MMC.

  1. A Three Phase Multi Level Converter For grid Connected PV System

    Directory of Open Access Journals (Sweden)

    S. Srikanth

    2014-07-01

    Full Text Available Photovoltaic energy is a wide kind of green energy. A high performance on these systems is needed to make the most of energy produced by solar cells. Also, there must be a constant adaptation due to the continuous variation of power production. Control techniques for Power Converters like the MPPT algorithm (Maximum Power Point Tracking present very good results on photovoltaic chains. Nevertheless, losses on power elements reduce global performance and the voltage/current adaptation is not always possible.  This paper presents a single-phase 11-level (5 H-bridges cascade multilevel DC-AC grid-tied inverter. Each inverter bridge is connected to a 200 W solar panel. OPAL-RT lab was used as the hardware in the loop (HIL real-time control system platform where a Maximum Power Point Tracking (MPPT algorithm was implemented based on the inverter output power to assure optimal operation of the inverter when connected to the power grid as well as a Phase Locked Loop (PLL for phase and frequency match. A novel SPWM scheme is proposed in this paper to be used with the solar panels that can account for voltage profile fluctuations among the panels during the day. Simulation and experimental results are shown for voltage and current during synchronization mode and power transferring mode to validate the methodology for grid connection of renewable resources.

  2. High luminous flux from single crystal phosphor-converted laser-based white lighting system

    KAUST Repository

    Cantore, Michael

    2015-12-14

    The efficiency droop of light emitting diodes (LEDs) with increasing current density limits the amount of light emitted per wafer area. Since low current densities are required for high efficiency operation, many LED die are needed for high power white light illumination systems. In contrast, the carrier density of laser diodes (LDs) clamps at threshold, so the efficiency of LDs does not droop above threshold and high efficiencies can be achieved at very high current densities. The use of a high power blue GaN-based LD coupled with a single crystal Ce-doped yttrium aluminum garnet (YAG:Ce) sample was investigated for white light illumination applications. Under CW operation, a single phosphor-converted LD (pc-LD) die produced a peak luminous efficacy of 86.7 lm/W at 1.4 A and 4.24 V and a peak luminous flux of 1100 lm at 3.0 A and 4.85 V with a luminous efficacy of 75.6 lm/W. Simulations of a pc-LD confirm that the single crystal YAG:Ce sample did not experience thermal quenching at peak LD operating efficiency. These results show that a single pc-LD die is capable of emitting enough luminous flux for use in a high power white light illumination system.

  3. Design of Two Feeder Three Phase Four Wire Distribution System Utilizing Multi Converter UPQC with Fuzzy Logic Controller

    Directory of Open Access Journals (Sweden)

    Chandra Babu Paduchuri

    2014-01-01

    Full Text Available This paper proposes the instantaneous p-q theory based fuzzy logic controller (FLC for multi converter unified power quality conditioner (MC-UPQC to mitigate power quality issues in two feeders three-phase four-wire distribution systems. The proposed system is extended system of the existing one feeder three-phase four-wire distribution system, which is operated with UPQC. This system is employed with three voltage source converters, which are connected commonly to two feeder distribution systems. The performance of this proposed system used to compensate voltage sag, neutral current mitigation and compensation of voltage and current harmonics under linear and nonlinear load conditions. The neutral current flowing in series transformers is zero in the implementation of the proposed system. The simulation performance analysis is carried out using MATLAB.

  4. System control module diagnostic Expert Assistant

    Science.gov (United States)

    Flores, Luis M.; Hansen, Roger F.

    1990-01-01

    The Orbiter EXperiments (OEX) Program was established by NASA's Office of Aeronautics and Space Technology (OAST) to accomplish the precise data collection necessary to support a complete and accurate assessment of Space Transportation System (STS) Orbiter performance during all phases of a mission. During a mission, data generated by the various experiments are conveyed to the OEX System Control Module (SCM) which arranges for and monitors storage of the data on the OEX tape recorder. The SCM Diagnostic Expert Assistant (DEA) is an expert system which provides on demand advice to technicians performing repairs of a malfunctioning SCM. The DEA is a self-contained, data-driven knowledge-based system written in the 'C' Language Production System (CLIPS) for a portable micro-computer of the IBM PC/XT class. The DEA reasons about SCM hardware faults at multiple levels; the most detailed layer of encoded knowledge of the SCM is a representation of individual components and layouts of the custom-designed component boards.

  5. Performance Enhancement of Hybrid Wind/Photo Voltaic System Using Z Source Inverter with Cuk-sepic Fused Converter

    Directory of Open Access Journals (Sweden)

    A. Nazar Ali

    2014-05-01

    Full Text Available This study presents a new method of design of z source inverter for improving the performance of the hybrid wind/photo voltaic system with cuk-sepic fused converter. The various drawbacks of the conventional converter are, it requires passive input filters, the generator current decreases its lifespan, increases the power loss due to heating. In proposed method, the Cuk-SEPIC fused converter is used, which eliminates the need of additional input filters to filter out high frequency harmonics. This configuration makes it possible for the wind source and photo voltaic source to supply the load separately or simultaneously depending on their availability. A simulation model for the hybrid wind/photovoltaic system has been developed using MATLAB/SIMULINK.

  6. Visual speech gestures modulate efferent auditory system.

    Science.gov (United States)

    Namasivayam, Aravind Kumar; Wong, Wing Yiu Stephanie; Sharma, Dinaay; van Lieshout, Pascal

    2015-03-01

    Visual and auditory systems interact at both cortical and subcortical levels. Studies suggest a highly context-specific cross-modal modulation of the auditory system by the visual system. The present study builds on this work by sampling data from 17 young healthy adults to test whether visual speech stimuli evoke different responses in the auditory efferent system compared to visual non-speech stimuli. The descending cortical influences on medial olivocochlear (MOC) activity were indirectly assessed by examining the effects of contralateral suppression of transient-evoked otoacoustic emissions (TEOAEs) at 1, 2, 3 and 4 kHz under three conditions: (a) in the absence of any contralateral noise (Baseline), (b) contralateral noise + observing facial speech gestures related to productions of vowels /a/ and /u/ and (c) contralateral noise + observing facial non-speech gestures related to smiling and frowning. The results are based on 7 individuals whose data met strict recording criteria and indicated a significant difference in TEOAE suppression between observing speech gestures relative to the non-speech gestures, but only at the 1 kHz frequency. These results suggest that observing a speech gesture compared to a non-speech gesture may trigger a difference in MOC activity, possibly to enhance peripheral neural encoding. If such findings can be reproduced in future research, sensory perception models and theories positing the downstream convergence of unisensory streams of information in the cortex may need to be revised.

  7. Several Modulation in Direct-Sequence Spectrum-Spread Systems

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Performances of BPSK, balanced-quaternary modulation, dual-quaternary modulation and complex-quaternary modulation in direct-sequence spectrum-spread (DS-SS) system are discussed in this paper. Based on the criterion the power of original signal is the same, it is shown that complex-quaternary modulation has the best performance, and dual-quaternary modulation degrades 2dB. Moreover, the frequency efficient of the two modulations is 2bit/Hz. Balanced-quaternary has the same performance as BPSK with frequency efficient 1bit/Hz.

  8. A Multiphase, Modular, Bidirectional, Triple-Voltage DC-DC Converter Power Systems

    Energy Technology Data Exchange (ETDEWEB)

    Su, Gui-Jia [ORNL; Tang, Lixin [ORNL

    2008-01-01

    Electrical power systems in future hybrid and fuel cell vehicles may employ three voltage [14 V, 42 V, and high voltage (HV)] nets. These will be necessary to accommodate existing 14-V loads as well as efficiently handle new heavy loads at the 42-V net and a traction drive on the HV bus. A low-cost DC-DC converter was proposed for connecting the three voltage nets. It minimizes the number of switches and their associated gate driver components by using two half-bridges and a high-frequency transformer. Another salient feature is that the half bridge on the 42-V bus is also utilized to provide the 14-V bus by operating at duty ratios around an atypical value of 1/3. Moreover, it makes use of the parasitic capacitance of the switches and the transformer leakage inductance for soft switching. The use of half bridges makes the topology well suited for interleaved multiphase modular configurations as a means to increase the power level because the capacitor legs can be shared. This paper presents simulation and experimental results on an interleaved two-phase arrangement rated at 4.5 kW. Also discussed are the benefits of operating with an atypical duty ratio on the transformer and a preferred multiphase configuration to minimize capacitor ripple currents.

  9. Nearshore Tests of the Tidal Compensation System for Point-Absorbing Wave Energy Converters

    Directory of Open Access Journals (Sweden)

    Valeria Castellucci

    2015-04-01

    Full Text Available The power production of the linear generator wave energy converter developed at Uppsala University is affected by variations of mean sea level. The reason is that these variations change the distance between the point absorber located on the surface and the linear generator located on the seabed. This shifts the average position of the translator with respect to the center of the stator, thereby reducing the generator output power. A device mounted on the point absorber that compensates for tides of small range by regulating the length of the connection line between the buoy at the surface and the linear generator has been constructed and tested. This paper describes the electro-mechanical, measurement, communication and control systems installed on the buoy and shows the results obtained before its connection to the generator. The adjustment of the line was achieved through a linear actuator, which shortens the line during low tides and vice versa. The motor that drives the mechanical device was activated remotely via SMS. The measurement system that was mounted on the buoy consisted of current and voltage sensors, accelerometers, strain gauges and inductive and laser sensors. The data collected were transferred via Internet to a Dropbox server. As described within the paper, after the calibration of the sensors, the buoy was assembled and tested in the waters of Lysekil harbor, a few kilometers from the Uppsala University research site. Moreover, the performance of the sensors, the motion of the mechanical device, the power consumption, the current control strategy and the communication system are discussed.

  10. Energy detection UWB system based on pulse width modulation

    Directory of Open Access Journals (Sweden)

    Song Cui

    2014-05-01

    Full Text Available A new energy detection ultra-wideband system based on pulse width modulation is proposed. The bit error rate (BER performance of this new system is slightly worst than that of a pulse position modulation (PPM system in additive white Gaussian noise channels. In multipath channels, this system does not suffer from cross-modulation interference as PPM, so it can achieve better BER performance than PPM when cross-modulation interference occurs. In addition, when synchronisation errors occur, this system is more robust than PPM.

  11. Emergency Control Aircraft System Using Thrust Modulation

    Science.gov (United States)

    Burken, John J. (Inventor); Burcham, Frank W., Jr. (Inventor)

    2000-01-01

    A digital longitudinal Aircraft Propulsion Control (APC system of a multiengine aircraft is provided by engine thrust modulation in response to comparing an input flightpath angle signal (gamma)c from a pilot thumbwheel. or an ILS system with a sensed flightpath angle y to produce an error signal (gamma)e that is then integrated (with reasonable limits) to generate a drift correction signal to be added to the error signal (gamma)e after first subtracting a lowpass filtered velocity signal Vel(sub f) for phugoid damping. The output error signal is multiplied by a constant to produce an aircraft thrust control signal ATC of suitable amplitude to drive a throttle servo for all engines. each of which includes its own full-authority digital engine control (FADEC) computer. An alternative APC system omits sensed flightpath angle feedback and instead controls the flightpath angle by feedback of the lowpass filtered velocity signal Vel(sub f) which also inherently provides phugoid damping. The feature of drift compensation is retained.

  12. Adaptive Hysteresis Band Current Control (AHB) with PLL of Grid Side Converter-Based Wind Power Generation System

    DEFF Research Database (Denmark)

    Guo, Yougui; Zeng, Ping; Li, Lijuan

    2011-01-01

    Adaptive hysteresis band current control(AHB CC) is used to control the three-phase grid currents by means of grid side converter in wind power generation system in this paper. AHB has reached the good purpose with PLL (Lock phase loop). First the mathematical models of each part are given...

  13. Adaptive Hysteresis Band Current Control (AHB) with PLL of Grid Side Converter-Based Wind Power Generation System

    DEFF Research Database (Denmark)

    Guo, Yougui; Zeng, Ping; Li, Lijuan

    2011-01-01

    Adaptive hysteresis band current control(AHB CC) is used to control the three-phase grid currents by means of grid side converter in wind power generation system in this paper. AHB has reached the good purpose with PLL (Lock phase loop). First the mathematical models of each part are given...

  14. A tapped-inductor buck-boost converter for a multi-DEAP generator energy harvesting system

    Science.gov (United States)

    Dimopoulos, Emmanouil; Munk-Nielsen, Stig

    2014-03-01

    Interest on Dielectric ElectroActive Polymer (DEAP) generators has aroused among scientists in recent years, due to the former ones' documented advantages against competing electromagnetic and field-activated technologies. Yet, the need for bidirectional energy flow under high step-up and high step-down voltage conversion ratios, accompanied by low-average but relatively high-peak currents, imposes great challenges on the design of the employed power electronic converter. On top of that, the shortage of commercially-available, high-efficient, high-voltage, low-power semiconductor devices limits the effective operational range of the power electronic converter. In this paper, a bidirectional tapped-inductor buck-boost converter is proposed, addressing high- efficient high step-up and high step-down voltage conversion ratios, for energy harvesting applications based on DEAP generators. The effective operational range of the converter is extended, by replacing its high-side switch with a string of three serialized MOSFETs, to accommodate the need for high-efficient high-voltage operation. Experiments conducted on a single DEAP generator - part of a quadruple DEAP generator energy harvesting system with all elements installed sequentially in the same circular disk with a 90° phase shift - validate the applicability of the proposed converter, demonstrating energy harvesting of 0.26 J, at 0.5 Hz and 60% delta- strain; characterized by an energy density of 1.25 J per kg of active material.

  15. A Single-Phase Multilevel Current-Source Converter using H-Bridge and DC Current Modules

    Directory of Open Access Journals (Sweden)

    Suroso Suroso

    2014-03-01

    Full Text Available This paper presents a different topology of H-bridge based multilevel current-source inverter (CSI. In this new topology, an H-bridge CSI is connected with a single or more current modules to generate a multilevel output current waveform with lower di/dt, and less distortion. Using the proposed multilevel CSI, the number of the power switching devices, and isolated gate drive circuits can be reduced. Moreover, chopper based DC current sources are presented to reduce the inductor size effectively to be in micro-Henry order, and ensure the balance of the intermediate current levels. The proposed topology is inherently able to reduce the inductor conduction losses if compared with the conventional multilevel CSIs and the H-bridge CSI. Seven-level PWM inverter configurations with non-isolated DC current sources and with a single DC power source are verified through computer simulations. Furthermore, laboratory prototypes of seven-level CSI is setup and tested. The results show that the inverter circuit works properly to generate the multilevel output current waveform with low harmonics currents, small inductors and with less conduction losses which proves feasibility of the proposed multilevel CSI. Normal 0 false false false EN-US X-NONE X-NONE

  16. Development of a pilot system for converting sweet potato starch into glucose syrup

    Science.gov (United States)

    Silayo, Valerian C K.; Lu, John Y.; Aglan, Heshmat A.; Bovell-Benjamin, A. C. (Principal Investigator)

    2003-01-01

    Sweet potato has been chosen as one of NASA's crops to support human beings in future space missions. One of the possible uses is to make syrup that can be used as a general sweetener. In this work a simple engineering system for converting sweet potato starch into glucose syrup was studied on a laboratory scale. The system comprises the following main units: a blender, continuous stirred tank reactor (CSTR), centrifugal and vacuum filters, deionization column and vacuum evaporator. The system was tested by carrying out conversion processes from fresh sweet potato roots. The roots were pealed, sliced, homogenized, heated and hydrolyzed by diastase of malt and Dextrozyme C (Novo Nordisk BioChem, North America, Inc.) enzymes in the CSTR. After hydrolysis the slurry was filtered, de-ionized and concentrated to get glucose syrup. The performance of the system was evaluated based on the quality of the conversion. The main factor was the level of reducing sugars except for the deionization where ash content and color were the main factors. Through careful control of the system units, good heating performance in the CSTR was obtained and the hydrolysis process attained sufficient conversion. The filtration process that incorporated the centrifuge was faster than when it was by-passed to the vacuum filter but losses in sugars were higher. Deionization removed more than 90% of the ash and reduced pigmentation, with probable insignificant losses in sugars during the deionization process. Recovery levels when the centrifuge was used and when it was by-passed could reach about 65% and 78%, respectively. These correspond to reducing sugar concentration of 259 and 310 mg/ml in 150-ml syrups from 300 g of sweet potatoes in each process. However, from concentration trials, syrups with volumes of 100 and 70 ml with the respective dextrose equivalence of 281 and 213 mg/ml were obtained. The syrups obtained were brownish in color and the process that employed centrifugal filtration

  17. Encapsulated Thermoelectric Modules for Advanced Thermoelectric Systems

    Science.gov (United States)

    Kambe, Mitsuru; Jinushi, Takahiro; Ishijima, Zenzo

    2014-06-01

    An encapsulated thermoelectric (TE) module consists of a vacuum-tight stainless-steel container in which an SiGe or BiTe TE module is encapsulated. This construction enables maximum performance and durability because: the thermal expansion mismatch between the hot and cold sides of the container can be accommodated by a sliding sheet in the container; the TE module inside is always kept in a vacuum environment, therefore no oxidation can occur; and the pressure difference between the inside and outside of the container reduces thermal contact resistance inside the container. Our encapsulated SiGe module features higher operating temperature—up to 650°C for both hot and cold sides. Other high-temperature modules and conventional BiTe modules, including both-sides and one-side skeleton types, have been encapsulated. Several variants of the encapsulated module are available. Encapsulated thermoelectric modules with integrated coolers contain cooling panels through which water can pass. If the module hot side is heated by a radiating heat source (radiation coupling) or convection of a hot gas or fluid (convection coupling), no pressing force on the module is necessary. It therefore features minimum contact resistance with the cooling duct, because no pressure is applied, maximum TE power, and minimum installation cost. Another, larger, variant is a quadruple flexible container in which four modules (each of maximum size 40 mm × 40 mm) are encapsulated. These encapsulated modules were used in a powder metallurgy furnace and were in use for more than 3000 h. Application to cryogenic temperatures simulating the liquid nitrogen gas vaporizer has been also attempted.

  18. Flexible distribution systems through the application of multi back-to-back converters. Concept, implementation and experimental verification

    Energy Technology Data Exchange (ETDEWEB)

    De Graaff, R.A.A.

    2010-05-26

    The objective of the research project is to investigate the use of a multi back-to-back converter to support the transition to active distribution networks. The investigation must explicitly not focus on finding the optimal power electronics topology, but rather on defining the role that such a device can play in a power distribution system and on the proof of principle. The possible tasks of this device are to actively control power flow and to maintain power quality and stability, both during normal operation and during fault conditions in medium voltage networks with distributed generation. The combination of this versatile converter system and the control and protection systems that define its functionality are in this thesis denoted as the Intelligent Node (IN). Research questions are: (1) Which are the main benefits of multi back-to-back converter devices in distribution systems?; (2) How and under which conditions can these benefits be achieved? What controls should be adopted?; (3) Which are the specific aspects that distinguish the application of the multi back-to-back devices in distribution systems from similar applications in transmission systems?; (4) Can this be demonstrated on a laboratory-scale set-up?Chapter 2 Distribution systems The relevant aspects of distribution systems are discussed. This includes power quality considerations, redundancy aspects, and voltage control methods. Chapter 3 (FACTS in distribution systems) describes power flow control principles. Also an overview is given of the state-of-the-art of power electronic applications for power flow control in electrical power systems. Chapter 4 (Functional concept of the Intelligent Node) gives the proposed functional concept for the application of a multi back-to-back converter device as IN (Intelligent Node). The applications are developed on a functional level, with the device at a black-box level. To satisfy the resulting requirements several technology options are analyzed, ending

  19. Test setup for accelerated test of high power IGBT modules with online monitoring of Vce and Vf voltage during converter operation

    DEFF Research Database (Denmark)

    de Vega, Angel Ruiz; Ghimire, Pramod; Pedersen, Kristian Bonderup;

    2014-01-01

    of the device in real application. The hypothesis is that ageing of power modules closer to real environment including cooling system, full dc-link voltage and continuous PWM operation could lead to more accurate study of failure mechanism. A new type of test setup is proposed, which can create different real...

  20. Integrated modeling and control of a PEM fuel cell power system with a PWM DC/DC converter

    Energy Technology Data Exchange (ETDEWEB)

    Choe, Song-Yul; Ahn, Jong-Woo [Mechanical Engineering Department, Auburn University, Auburn, AL 36848 (United States); Lee, Jung-Gi [Electrical Engineering Department, Pohang University of Science and Technology, Pohang (Korea); Baek, Soo-Hyun [Electrical Engineering Department, Dong-guk University, Seoul (Korea)

    2007-02-10

    A fuel cell powered system is regarded as a high current and low voltage source. To boost the output voltage of a fuel cell, a DC/DC converter is employed. Since these two systems show different dynamics, they need to be coordinated to meet the demand of a load. This paper proposes models for the two systems with associated controls, which take into account a PEM fuel cell stack with air supply and thermal systems, and a PWM DC/DC converter. The integrated simulation facilitates optimization of the power control strategy, and analyses of interrelated effects between the electric load and the temperature of cell components. In addition, the results show that the proposed power control can coordinate the two sources with improved dynamics and efficiency at a given dynamic load. (author)

  1. Energy Storage System by Means of Improved Thermal Performance of a 3 MW Grid Side Wind Power Converter

    DEFF Research Database (Denmark)

    Qin, Zian; Liserre, Marco; Blaabjerg, Frede

    2013-01-01

    method of the energy storage system. Then the conventional thermal evaluation approach is simplified for evaluation with long term wind profile. The case studies are done to address the optimal power size and capacity of the energy storage system by comparing the improvement of the thermal performance......Wind speed variations make the power of wind turbine system to fluctuate, which could increase the thermal stress of the power converter and reduce its lifetime. In order to relieve this problem, short-term energy storage technologies are applied to improve the thermal performance of a 3 MW grid...... side wind power converter. The cost, weight and cycle life of the energy storage technologies are evaluated based on a typical low speed high turbulence wind profile. In detail, a wind turbine system model is established and its control strategy is illustrated, which is followed by the power control...

  2. Remote monitoring of solar PV system for rural areas using GSM, V-F & F-V converters

    Science.gov (United States)

    Tejwani, R.; Kumar, G.; Solanki, C. S.

    2016-05-01

    The Small capacity photovoltaic (PV) systems like solar lantern and home lighting systems installed in remote rural area often fail without any prior warning due to lack of monitoring and maintenance. This paper describes implementation of remote monitoring for small capacity solar PV system that uses GSM voice channel for communication. Through GSM analog signal of sine wave with frequency range 300-3500 Hz and amplitude range 2.5-4 V is transmitted. Receiver is designed to work in the same frequency range. The voltage from solar PV system in range of 2 to 7.5 V can be converted to frequency directly at the transmitting end. The frequency range from 300-6000 Hz can be sensed and directly converted to voltage signal at receiving end. Testing of transmission and reception of analog signal through GSM voice channel is done for voltage to frequency (V-F) and frequency to voltage (F-V) conversions.

  3. Connect Global Positioning System RF Module

    Science.gov (United States)

    Franklin, Garth W.; Young, Lawrence E.; Ciminera, Michael A.; Tien, Jeffrey Y.; Gorelik, Jacob; Okihiro, Brian Bachman; Koelewyn, Cynthia L.

    2012-01-01

    The CoNNeCT Global Positioning System RF Module (GPSM) slice is part of the JPL CoNNeCT Software Defined Radio (SDR). CoNNeCT is the Communications, Navigation, and Net working reconfigurable Testbed project that is part of NASA's Space Communication and Nav igation (SCaN) Program. The CoNNeCT project is an experimental dem onstration that will lead to the advancement of SDRs and provide a path for new space communication and navigation systems for future NASA exploration missions. The JPL CoNNeCT SDR will be flying on the International Space Station (ISS) in 2012 in support of the SCaN CoNNeCT program. The GPSM is a radio-frequency sampler module (see Figure 1) that directly sub-harmonically samples the filtered GPS L-band signals at L1 (1575.42 MHz), L2 (1227.6 MHz), and L5 (1176.45 MHz). The JPL SDR receives GPS signals through a Dorne & Margolin antenna mounted onto a choke ring. The GPS signal is filtered against interference, amplified, split, and fed into three channels: L1, L2, and L5. In each of the L-band channels, there is a chain of bandpass filters and amplifiers, and the signal is fed through each of these channels to where the GPSM performs a one-bit analog-to-digital conversion (see Figure 2). The GPSM uses a sub-harmonic, single-bit L1, L2, and L5 sampler that samples at a clock rate of 38.656 MHz. The new capability is the down-conversion and sampling of the L5 signal when previous hardware did not provide this capability. The first GPS IIF Satellite was launched in 2010, providing the new L5 signal. With the JPL SDR flying on the ISS, it will be possible to demonstrate navigation solutions with 10-meter 3-D accuracy at 10-second intervals using a field-program mable gate array (FPGA)-based feedback loop running at 50 Hz. The GPS data bits will be decoded and used in the SDR. The GPSM will also allow other waveforms that are installed in the SDR to demonstrate various GNSS tracking techniques.

  4. Online Fault Identification Based on an Adaptive Observer for Modular Multilevel Converters Applied to Wind Power Generation Systems

    Directory of Open Access Journals (Sweden)

    Hui Liu

    2015-07-01

    Full Text Available Due to the possibility of putting a large number of modules consisting of switches and capacitors connected in series, the modular multilevel converter (MMC can easily be scaled to high power and high voltage power conversion, which is an attractive feature for filter-less and transformer-less design and helpful to achieve high efficiency. However, a significantly increased amount of sub-modules in a MMC may increase the requirements for sensors and also increase the risk of failures. As a result, fault detection and diagnosis of MMC sub-modules are of great importance for continuous operation and post-fault maintenance. Therefore, in this paper, an effective fault diagnosis technique for real-time diagnosis of the switching device faults covering both the open-circuit faults and the short-circuit faults in MMC sub-modules is proposed, in which the faulty phase and the fault type is detected by analyzing the difference among the three output load currents, while the localization of the faulty switches is achieved by comparing the estimation results by the adaptive observer. In contrast to other methods that use additional sensors or devices, the presented technique uses the measured phase currents only, which are already available for MMC control. In additional, its operation, effectiveness and robustness are confirmed by simulation results under different operating conditions and load conditions.

  5. Thermal stress comparison in modular power converter topologies for smart transformers in the electrical distribution system

    DEFF Research Database (Denmark)

    Andresen, Markus; Ma, Ke; Liserre, Marco

    2015-01-01

    A Smart Transformer (ST) can cover an important managing role in the future electrical distribution grid. For the moment, the reliability and cost are not competitive with traditional transformers and create a barrier for its application. This work conduct detail designs and analysis for a promis......A Smart Transformer (ST) can cover an important managing role in the future electrical distribution grid. For the moment, the reliability and cost are not competitive with traditional transformers and create a barrier for its application. This work conduct detail designs and analysis...... for a promising modular ST solution, which is composed of Modular Multi-level converter, Quad Active Bridge DC-DC converters, and two-level voltage source converters. The focus is put on the loading conditions and thermal stress of power semiconductor devices in order to discover critical parts of the whole...

  6. Application of Theory of Hybrid Systems to Control the Switching of Buck Converter

    KAUST Repository

    Benmiloud, Mohammed

    2013-08-01

    The field of power electronics poses challenging control problems that can’t be treated in a complete manner using traditional modeling. In this paper, the buck converter operating in Continuous Conduction Mode (CCM) is represented analytically by hybrid automaton model and graphically representation is also given. The hybrid trajectory and the model behavior are presented. The control problem of buck switching converters is transformed to a guard selection problem. The guard selection calculation formulas of buck converter are derived from the basic circuit laws. The stability of the switching is established analytically by the use of multiple Lyapunov functions to ensure the convergence and Poincare map to assess the local stability of the limit cycle. Numerical results clearly bring out the advantages and effectiveness of the proposed control law under varying line voltage and load conditions. Simulation studies are carried out in Matlab/Simulink/Stateflow.

  7. 采用逆阻型子模块的新型模块化多电平换流器%Novel Modular Multilevel Converter With Reverse Blocking Sub-modules

    Institute of Scientific and Technical Information of China (English)

    杨晓峰; 薛尧; 郑琼林; 林智钦; 牟雅洁; 陈博伟; 五十岚征辉

    2016-01-01

    Modular multilevel converter (MMC) is one of the promising voltage source converter topologies in the field of high voltage direct current (HVDC) transmission system. Based on analysis of the existing sub-module topologies, an improved half-bridge sub-module topology based on reverse blocking IGBTs (RB-HBSM) was proposed for solving the fault ride through issues. In this paper, the fault current blocking mechanism and the electrical stress of the main power switches were studied firstly in detail. Then the fault control flow chart was presented. Feasibility of the proposed sub-module topology and the fault protection theory were verified by simulation. The proposed RB-HBSM-MMC topology is able to block the fault current without changing the original control and modulation strategies compared with the conventional MMC, thus it further reduces the complicity of industry design.%模块化多电平换流器(modular multilevel converter, MMC)是高压直流输电系统领域中极具工程应用前景的电压源拓扑之一。在分析典型子模块拓扑特点的基础上,该文提出一种新型的逆阻型半桥子模块(reverse blocking half bridge sub-module,RB-HBSM)的MMC拓扑,用于解决传统MMC的故障穿越能力问题。开展了RB-HBSM及其构成的 MMC 拓扑的故障电流阻断机理及其主要功率开关器件的电气应力分析研究,提出了故障控制流程,最后通过仿真算例对所提出的子模块拓扑进行了验证。仿真结果表明,新型RB-HBSM-MMC拓扑在不改变原有控制策略与调制策略的情况下,能够迅速实现故障电流阻断效果,有助于进一步降低系统的复杂程度。

  8. WDM Phase-Modulated Millimeter-Wave Fiber Systems

    DEFF Research Database (Denmark)

    Yu, Xianbin; Prince, Kamau; Gibbon, Timothy Braidwood

    2012-01-01

    This chapter presents a computer simulation case study of two typical WDM phase-modulated millimeter-wave systems. The phase-modulated 60 GHz fiber multi-channel transmission systems employ single sideband (SSB) and double sideband subcarrier modulation (DSB-SC) schemes and present one of the lat......This chapter presents a computer simulation case study of two typical WDM phase-modulated millimeter-wave systems. The phase-modulated 60 GHz fiber multi-channel transmission systems employ single sideband (SSB) and double sideband subcarrier modulation (DSB-SC) schemes and present one...... of the latest research efforts in the rapidly emerging Radio-over-Fiber (RoF) application space for in-house access networks....

  9. Li-Ion Battery Charging with a Buck-Boost Power Converter for a Solar Powered Battery Management System

    OpenAIRE

    2013-01-01

    This paper analyzes and simulates the Li-ion battery charging process for a solar powered battery management system. The battery is charged using a non-inverting synchronous buck-boost DC/DC power converter. The system operates in buck, buck-boost, or boost mode, according to the supply voltage conditions from the solar panels. Rapid changes in atmospheric conditions or sunlight incident angle cause supply voltage variations. This study develops an electrochemical-based equivalent circuit mod...

  10. A closed-loop biorefining system to convert organic residues into fuels

    Science.gov (United States)

    Chen, Rui

    This project delivers an energy positive and water neutral, closed-loop biorefining system that converts organic wastes into renewable energy and reduces the overall impacts on the environment. The research consisted of three major stages: The first stage of this project was conducted in an anaerobic co-digestion system. Effects of the ratio of dairy manure-to-food waste as well as operating temperature were tested on the performance of the co-digestion system. Results illustrated an increase in biogas productivity with the increase of supplemental food waste; fiber analysis revealed similar chemical composition (cellulose, hemicellulose and lignin) of final solid digestate regardless their different initial feedstock blends and digestion conditions. The molecular genetic analyses demonstrated that anaerobic methanogenic microorganisms were able to adjust their community assemblage to maximize biogas production and produce homogenized solid digestate. The second stage utilized electrocoagulation (EC) pretreated liquid digestate from previous stage to culture freshwater algae. Kinetics study showed a similar maximum growth rate (0.201-0.207 g TS day-1) in both 2x and 5x dilutions of EC solution; however, the algal growth was inhibited in original EC solution (1x), possibly due to the high ammonia-to-phosphate ratio. Algal community assemblage changed drastically in different dilutions of EC solution after a 9-day culture. The following semi-continuous culture in 2x and 5x EC media established steady biomass productivities and nitrogen removal rates; in addition, both conditions illustrated a phenomenon of phosphorus luxury uptake. Biomass composition analyses showed that algae cultured in medium containing higher nitrogen (2x EC medium) accumulated more protein but less carbohydrate and lipid than the 5x EC medium. The last stage involved hydrolyzing the algal biomass cultured in anaerobic digestion effluent and analyzing the effects of the neutralized algal

  11. A Sliding Surface-Regulated Current-Mode Pulse-Width Modulation Controller for a Digital Signal Processor-Based Single Ended Primary Inductor Converter-Type Power Factor Correction Rectifier

    National Research Council Canada - National Science Library

    Hsin-Jang Shieh; Ying-Zuo Chen

    2017-01-01

    To efficiently supply wide-range DC voltage from a pulse-width modulation (PWM) rectifier, this paper presents a single-phase, full-wave, diode-bridge, single-ended primary-inductor converter-type (SEPIC-type...

  12. Clean fuels from biomass. [feasibility of converting plant systems to fuels

    Science.gov (United States)

    Hsu, Y. Y.

    1974-01-01

    The feasibility of converting biomass to portable fuels is studied. Since plants synthesize biomass from H2O and CO2 with the help of solar energy, the conversion methods of pyrolysis, anaerobic fermentation, and hydrogenation are considered. Cost reduction methods and cost effectiveness are emphasized.

  13. High Efficiency Non-isolated Three Port DC-DC Converter for PV-Battery Systems

    DEFF Research Database (Denmark)

    Tomas Manez, Kevin; Anthon, Alexander; Zhang, Zhe

    2016-01-01

    This paper presents a nonisolated Three Port Converter (TPC) with a unidirectional port for photovoltaic (PV) panels and a bidirectional port for energy storage. With the proposed topology single power conversion is performed between each port, so high efficiencies are obtained. A theoretical...

  14. High Efficiency Non-isolated Three Port DC-DC Converter for PV-Battery Systems

    DEFF Research Database (Denmark)

    Tomas Manez, Kevin; Anthon, Alexander; Zhang, Zhe;

    2016-01-01

    This paper presents a nonisolated Three Port Converter (TPC) with a unidirectional port for photovoltaic (PV) panels and a bidirectional port for energy storage. With the proposed topology single power conversion is performed between each port, so high efficiencies are obtained. A theoretical ana...

  15. High Efficiency Power Converter for a Doubly-fed SOEC/SOFC System

    DEFF Research Database (Denmark)

    Tomas Manez, Kevin; Anthon, Alexander; Zhang, Zhe

    2016-01-01

    modes is possible. This paper discusses the design considerations for this novel PCU, and verifies its operation principle with Matlab/Simulink simulations. Experimental results on a tailored dc-dc converter confirm the design simplifications for high efficiency operation along the entire power...

  16. Analysis of DC/DC Converter Efficiency for Energy Storage System Based on Bidirectional Fuel Cells

    DEFF Research Database (Denmark)

    Pittini, Riccardo; Zhang, Zhe; Andersen, Michael A. E.

    2013-01-01

    Renewable energy sources are fluctuating depending on the availability of the energy source. For this reason, energy storage is becoming more important and bidirectional fuel cells represent an attractive technology. Fuel cells require highcurrent low-voltage dc-dc or dc-ac converters as power...

  17. Integrated module inverter using a zeta DC-DC converter with feedforward MPPT (Maximum Power Point Tracking) control; Inversor modulo integrado utilizando um conversor CC-CC zeta com controle MPPT feedforward

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, Henrique Fioravanti Miguel

    2009-08-15

    This work presents the study and development of a processing power system that could be used in the connection of renewable energy sources to commercial power grid. The system consists of a ZETA converter associated with a bridge inverter operating at low frequency. The Zeta converter, operating in discontinuous conduction mode (DCM), plays the main role in this arrangement, producing a rectified sinusoidal current waveform synchronized with the electric grid. The function of the full-bridge inverter, connected in cascade with the Zeta converter, is to reverse every 180 deg the current generated by the Zeta converter. Initially it presents the analysis of the Zeta converter operating in DCM, as well as a design criterion. Following by the control strategy and the experimental results for the proposed system are presented and discussed. (author)

  18. Lunar Module Electrical Power System Design Considerations and Failure Modes

    Science.gov (United States)

    Interbartolo, Michael

    2009-01-01

    This slide presentation reviews the design and redesign considerations of the Apollo lunar module electrical power system. Included in the work are graphics showing the lunar module power system. It describes the in-flight failures, and the lessons learned from these failures.

  19. Optimized MPPT-based converter for TEG energy harvester to power wireless sensor and monitoring system in nuclear power plant

    Science.gov (United States)

    Xing, Shaoxu; Anakok, Isil; Zuo, Lei

    2017-04-01

    Accidents like Fukushima Disasters push people to improve the monitoring systems for the nuclear power plants. Thus, various types of energy harvesters are designed to power these systems and the Thermoelectric Generator (TEG) energy harvester is one of them. In order to enhance the amount of harvested power and the system efficiency, the power management stage needs to be carefully designed. In this paper, a power converter with optimized Maximum Power Point Tracking (MPPT) is proposed for the TEG Energy Harvester to power the wireless sensor network in nuclear power plant. The TEG Energy Harvester is installed on the coolant pipe of the nuclear plant and harvests energy from its heat energy while the power converter with optimized MPPT can make the TEG Energy Harvester output the maximum power, quickly response to the voltage change and provide sufficient energy for wireless sensor system to monitor the operation of the nuclear power plant. Due to the special characteristics of the Single-Ended Primary Inductor Converter (SEPIC) when it is working in the Discontinuous Inductor Current Mode (DICM) and Continuous Conduction Mode (CCM), the MPPT method presented in this paper would be able to control the converter to achieve the maximum output power in any working conditions of the TEG system with a simple circuit. The optimized MPPT algorithm will significantly reduce the cost and simplify the system as well as achieve a good performance. Experiment test results have shown that, comparing to a fixed- duty-cycle SEPIC which is specifically designed for the working on the secondary coolant loop in nuclear power plant, the optimized MPPT algorithm increased the output power by 55%.

  20. Optimal Power System and Grid Interface Design Considerations for the CLICs Klystron Modulators

    CERN Document Server

    Marija, Jankovic; Jon, Clare; Pat, Wheeler; Davide, Aguglia

    2015-01-01

    The Compact Linear Collider (CLIC) is an electron-positron collider under study at CERN with the aim to explore the next generation of high precision/high energy particles physics. The CLIC’s drive beams will be accelerated by approximately 1300 klystrons, requiring highly efficient and controllable solid state capacitor discharge modulators. Capacitor charger specifications include the requirement to mask the pulsed effect of the load from the utility grid, ensure maximum power quality, control the derived DC voltage precisely (to maximize accuracy for the modulators being implemented), and achieve high efficiency and operability of the overall power system. This paper presents the work carried out on the power system interface for the CLIC facility. In particular it discusses the challenges on the utility interface and analysis of the grid interface converters with regards to required functionality, efficiency, and control methodologies.

  1. A Novel Active Bouncer System for Klystron Modulators with Constant AC Power Consumption

    CERN Document Server

    Cabaleiro Magallanes, F; Viarouge, P; Cros, J; De Almeida Martins, C

    2014-01-01

    This paper presents the principles and design methodologies of a novel active bouncer system, to be implemented in a transformer-based klystron modulator, which is able to meet two different objectives: 1. Regulate the output pulse voltage flattop, and 2. Attenuate the power fluctuation withdrawn from the AC network. This solution allows the utilization of a standard constant voltage / constant current power supply as a capacitor charger. The solution consists of a 4-quadrant switching converter placed in series with the main capacitor bank (forming a unique element in parallel with the capacitor charger), controlled with specific feed-back loops to achieve the two objectives. The complete design method, including a numerical optimization, of the whole system, is presented in the paper. Analyses of the compromises between the active bouncer specifications and the other modulator sub-components design is presented as well.

  2. SiC Multi-Chip Power Modules as Power-System Building Blocks

    Science.gov (United States)

    Lostetter, Alexander; Franks, Steven

    2007-01-01

    and difficulty of designing new, highly reliable power systems would be reduced considerably. Several prototype DC-to-DC power-converter modules containing SiC power-switching devices were designed and built to demonstrate the feasibility of the SiC MCPM concept. In anticipation of a future need for operation at high temperature, the circuitry in the modules includes high-temperature inductors and capacitors. These modules were designed to be stacked to construct a system of four modules electrically connected in series and/or parallel. The packaging of the modules is designed to satisfy requirements for series and parallel interconnection among modules, high power density, high thermal efficiency, small size, and light weight. Each module includes four output power connectors two for serial and two for parallel output power connections among the modules. Each module also includes two signal connectors, electrically isolated from the power connectors, that afford four zones for signal interconnections among the SOI controllers. Finally, each module includes two input power connectors, through which it receives power from an in-line power bus. This design feature is included in anticipation of a custom-designed power bus incorporating sockets compatible with snap-on type connectors to enable rapid replacement of failed modules.

  3. Effect of signal modulating noise in bistable stochastic dynamical systems

    Institute of Scientific and Technical Information of China (English)

    肖方红; 闫桂荣; 张新武

    2003-01-01

    The effect of signal modulating noise in bistable stochastic dynamical systems is studied.The concept of instan taneous steady state is proposed for bistable dynamical systems.By making a dynamical analysis of bistable stochastic systems,we find that global and local effect of signal modulating noise as well as stochastic resonance can occur in bistable dynamical systems on which both a weak sinusoidal signal and noise are forced.The effect is demonstrated by numerical simulation.

  4. Hybrid electric system based on fuel cell and battery and integrating a single dc/dc converter for a tramway

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, Luis M., E-mail: luis.fernandez@uca.e [Department of Electrical Engineering, EPS Algeciras, University of Cadiz, Avda. Ramon Puyol, s/n. 11202 Algeciras (Cadiz) (Spain); Garcia, Pablo, E-mail: pablo.garcia@uca.e [Department of Electrical Engineering, EPS Algeciras, University of Cadiz, Avda. Ramon Puyol, s/n. 11202 Algeciras (Cadiz) (Spain); Garcia, Carlos Andres, E-mail: carlosandres.garcia@uca.e [Department of Electrical Engineering, EPS Algeciras, University of Cadiz, Avda. Ramon Puyol, s/n. 11202 Algeciras (Cadiz) (Spain); Jurado, Francisco, E-mail: fjurado@ujaen.e [Department of Electrical Engineering, EPS Linares, University of Jaen, C/Alfonso X, No. 28. 23700 Linares (Jaen) (Spain)

    2011-05-15

    Research highlights: {yields} Hybrid electric power system for a real surface tramway. {yields} Hybrid system based on PEM fuel cell with dc/dc converter and Ni-MH battery. {yields} New control strategy for the energy management of the tramway. {yields} Hybrid system demonstrated to meet appropriate driving cycle of the tramway. -- Abstract: This paper presents a hybrid electric power system for a real surface tramway. The hybrid system consists of two electrical energy sources integrating a single dc/dc converter to provide the power demanded by the tramway loads (four electric traction motors and auxiliary services): (1) a Polymer Electrolyte Membrane (PEM) fuel cell (FC) as the primary and (2) a rechargeable Ni-MH battery as electrical energy storage to supplement the FC over the driving cycle. According to the requirements of the real driving cycle of the tramway, it was considered a 200 kW PEM FC system with two FCs connected in parallel and a 34 Ah Ni-MH battery. The PEM FC and Ni-MH battery models were designed from commercially available components. The power conditioning system provides the appropriate power for the tramway. It is composed of: (1) a unique dc/dc boot converter which adapts the FC output voltage to the 750 V traction standard dc bus; (2) three phase inverters to drive properly each electric motors; and (3) a braking chopper to dissipate excess of regenerative braking energy. Suitable state machine control architecture is presented for the hybrid system, its objective being to provide demanded power by the driving cycle, optimizing the energy generated. Following this objective, a new state machine control strategy based on eight states decides the operating point of each component of the system and a cascade control structure allows achieving the operating points determined by the strategy. Simulation results of the real driving cycle of the tramway check the adequacy of the hybrid electric power system.

  5. Reduced-Capacity Inrush Current Suppressor Using a Matrix Converter in a Wind Power Generation System with Squirrel-Cage Induction Machines

    Directory of Open Access Journals (Sweden)

    Sho Shibata

    2016-03-01

    Full Text Available This paper describes the reduced capacity of the inrush current suppressor using a matrix converter (MC in a large-capacity wind power generation system (WPGS with two squirrel-cage induction machines (SCIMs. These SCIMs are switched over depending on the wind speed. The input side of the MC is connected to the source in parallel. The output side of the MC is connected in series with the SCIM through matching transformers. The modulation method of the MC used is direct duty ratio pulse width modulation. The reference output voltage of the MC is decided by multiplying the SCIM current with the variable control gain. Therefore, the MC performs as resistors for the inrush current. Digital computer simulation is implemented to confirm the validity and practicability of the proposed inrush current suppressor using PSCAD/EMTDC (power system computer-aided design/electromagnetic transients including DC. Furthermore, the equivalent resistance of the MC is decided by the relationship between the equivalent resistance and the capacity of the MC. Simulation results demonstrate that the proposed inrush current suppressor can suppress the inrush current perfectly.

  6. Three-phase electronic power converter for photovoltaic system connected to power line; Conversor eletronico de potencia trifasico para sistema fotovoltaico conectado a rede eletrica

    Energy Technology Data Exchange (ETDEWEB)

    Villalva, Marcelo Gradella

    2010-10-15

    This work is a contribution to the study of power converters for photovoltaic distributed generation systems. The main objective is to present the development and results of a three phase power converter for a grid-connected photovoltaic plant. The work presents experimental results and theoretical studies on the modeling and simulation of photovoltaic devices, regulation of the photovoltaic voltage, maximum power point tracking, and the modeling and control of a two-stage grid-connected power converter. (author)

  7. Topological variations of the inverse dual converter for high-power dc-dc distribution systems

    Science.gov (United States)

    Ehsani, Mehrdad; Laskai, Laszlo

    New dc-to-dc converter topologies are presented which are suitable for high density high power supplies. Topological variations of the basic inverse dual converter (IDC) circuit such as the transformer coupled, the multiphase and the multipulse derivation of the single phase IDC have been analyzed and some simulation results have been presented. The single phase IDC offers a buck-boost operation over wide range without transformer, bidirectional power flow, and complementary commutation of the switches. The topologies examined in this paper have additional features such as lower device and component stresses, and smaller filter requirements, resulting in smaller size and weight. Some performance and possible applications are also examined. IDCs for serial and parallel power distribution, and ac tapping of the IDC are discussed.

  8. A 99%-efficiency GaN converter for 6.78 MHz magnetic resonant wireless power transfer system

    Directory of Open Access Journals (Sweden)

    Yoshiyuki Akuzawa

    2014-10-01

    Full Text Available The authors developed a high-efficiency gallium-nitride (GaN Class-E converter for a 6.78 MHz magnetic resonant wireless power transfer system. A negative-bias gate driver circuit made it possible to use a depletion mode GaN high-electron-mobility transistor (HEMT, and simplified the converter circuit. As the depletion mode GaN HEMT with very small gate–source capacitance provided almost ideal zero-voltage switching, the authors attained a drain efficiency of 98.8% and a total efficiency of 97.7%, including power consumption of a gate driver circuit, at a power output of 33 W. In addition, the authors demonstrated a 6.78 MHz magnetic resonant wireless power transfer system that consisted of the GaN Class-E converter, a pair of magnetic resonant coils 150 mm in diameter with an air-gap distance of 40 mm, and a full-bridge rectifier using Si Schottky barrier diodes. The system achieved a dc–dc efficiency of 82.8% at a power output of 25 W. The efficiencies of coil coupling and the rectifier were estimated to be ∼ 94 and 90%, respectively.

  9. System Tests with DC-DC Converters for the CMS Silicon Strip Tracker at SLHC

    CERN Document Server

    Klein, K; Karpinski, W; Merz, J; Sammet, J

    2008-01-01

    The delivery of power is considered to be one of the major challenges for the upgrade of the CMS silicon strip tracker for SLHC. The inevitable increase in granularity and complexity of the device is expected to result in a power consumption comparable or even higher than the power consumption of todays' strip tracker. However, the space available for cables will remain the same. In addition, a further increase of the tracker material budget due to cables and cooling is considered inacceptable, as the performance of the CMS detector must not be compromised for the upgrade. Novel powering schemes such as serial powering or usage of DC-DC converters have been proposed to solve the problem. To test the second option, substructures of the current CMS silicon strip tracker have been operated for the first time with off-the-shelf DC-DC buck converters as well as with first prototypes of custom-designed DC-DC converters. The tests are described and the results are discussed.

  10. Direct Digital Modulation Converter (DDMC)

    Science.gov (United States)

    1976-01-01

    Command ’ennit lully le^ible reproducüon Griffiss Air Force Base, New York 13441 \\ ,t.-:...u^.S:>.;v..x.>.^:-:^-i pn^ m«jLii(j|iBP»iiijipii This...34,",’. ■ " mm umWMWffUBPWPWpilW ^n m 127 iSliiAHäiii^iMw^^^iÜSa«^^ i-^^V::^-.-: i.Vi.---. ^^ JB ^Ü^^-^ _ LALJ^fc „..„,._.....,..._.._ ,._ _,.., ii...aassaa’asÄRüissssfeSS?;» ouuuuuuuuuouuuuuu 142 ü^ulriBä^.;...;.;.:’.:^ . ■ ^■-■■.-^■^ . ..-^u^.^ ^ >.-JI ^B- jB ^t.-jji^.^i-.-a

  11. Simulation of Standby Efficiency Improvement for a Line Level Control Resonant Converter Based on Solar Power Systems

    Directory of Open Access Journals (Sweden)

    Ming-Tse Kuo

    2015-01-01

    Full Text Available This paper proposes a new scheme to improve the standby efficiency of the high-power half-bridge line level control (LLC resonant converter. This new circuit is applicable to improving the efficiency of the renewable energy generation system in distributed power systems. The main purpose is to achieve high-efficiency solar and wind power and stable output under different load conditions. In comparison with the traditional one, this novel method can improve standby efficiency at standby. The system characteristics of this proposed method have been analyzed through detailed simulations, which prove its feasibility.

  12. Cascaded resonant bridge converters

    Science.gov (United States)

    Stuart, Thomas A. (Inventor)

    1989-01-01

    A converter for converting a low voltage direct current power source to a higher voltage, high frequency alternating current output for use in an electrical system where it is desired to use low weight cables and other circuit elements. The converter has a first stage series resonant (Schwarz) converter which converts the direct current power source to an alternating current by means of switching elements that are operated by a variable frequency voltage regulator, a transformer to step up the voltage of the alternating current, and a rectifier bridge to convert the alternating current to a direct current first stage output. The converter further has a second stage series resonant (Schwarz) converter which is connected in series to the first stage converter to receive its direct current output and convert it to a second stage high frequency alternating current output by means of switching elements that are operated by a fixed frequency oscillator. The voltage of the second stage output is controlled at a relatively constant value by controlling the first stage output voltage, which is accomplished by controlling the frequency of the first stage variable frequency voltage controller in response to second stage voltage. Fault tolerance in the event of a load short circuit is provided by making the operation of the first stage variable frequency voltage controller responsive to first and second stage current limiting devices. The second stage output is connected to a rectifier bridge whose output is connected to the input of the second stage to provide good regulation of output voltage wave form at low system loads.

  13. Operators Manual and Technical Reference for the Z-Beamlet Phase Modulation Failsafe System: Version 1.

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, Darrell J.

    2014-09-01

    The need for pulse energies exceeding 4 kJ and pulse lengths [?] 2 ns in Sandia's Z-Beamlet laser (ZBL) requires that the single-frequency spectrum of its fiber-laser master oscillator be converted to a phase modulated spectrum with a modulation in dex [?] 5. Because accidental injection of single-frequency light into ZBL could result i n damage to optical materials from transverse stimulated Brillouin scattering, the presence of phase modulated (PM) light must be monitored by a reliable failsafe system that can stop a las er shot within of a few 10's of ns following a failure of the PM system. This requirement is met by combining optical heterodyne detection with high-speed electronics to indicate the pres ence or absence of phase modulated light. The transition time for the failsafe signal resultin g from a sudden failure using this technique is approximately 35 ns. This is sufficiently short to safely stop a single-frequency laser pulse from leaving ZBL's regenerative amplifier with a n approximately 35 ns margin of safety. This manual and technical reference contains detai led instructions for daily use of the PM failsafe system and provides enough additional informat ion for its maintenance and repair.

  14. Li-Ion Battery Charging with a Buck-Boost Power Converter for a Solar Powered Battery Management System

    Directory of Open Access Journals (Sweden)

    Chien-Wei Ma

    2013-03-01

    Full Text Available This paper analyzes and simulates the Li-ion battery charging process for a solar powered battery management system. The battery is charged using a non-inverting synchronous buck-boost DC/DC power converter. The system operates in buck, buck-boost, or boost mode, according to the supply voltage conditions from the solar panels. Rapid changes in atmospheric conditions or sunlight incident angle cause supply voltage variations. This study develops an electrochemical-based equivalent circuit model for a Li-ion battery. A dynamic model for the battery charging process is then constructed based on the Li-ion battery electrochemical model and the buck-boost power converter dynamic model. The battery charging process forms a system with multiple interconnections. Characteristics, including battery charging system stability margins for each individual operating mode, are analyzed and discussed. Because of supply voltage variation, the system can switch between buck, buck-boost, and boost modes. The system is modeled as a Markov jump system to evaluate the mean square stability of the system. The MATLAB based Simulink piecewise linear electric circuit simulation tool is used to verify the battery charging model.

  15. Electro-Mechanical Modeling and Performance Analysis of Floating Wave Energy Converters Utilizing Yo-Yo Vibrating System

    Energy Technology Data Exchange (ETDEWEB)

    Sim, Kyuho; Park, Jisu [Seoul National University, Seoul (Korea, Republic of); Jang, Seon-Jun [Innovation KR, Seoul (Korea, Republic of)

    2015-01-15

    This paper proposes a floating-type wave energy conversion system that consists of a mechanical part (yo-yo vibrating system, motion rectifying system, and power transmission system) and electrical part (power generation system). The yo-yo vibrating system, which converts translational input to rotational motion, is modeled as a single degree-of-freedom system. It can amplify the wave input via the resonance phenomenon and enhance the energy conversion efficiency. The electromechanical model is established from impedance matching of the mechanical part to the electrical system. The performance was analyzed at various wave frequencies and damping ratios for a wave input acceleration of 0.14 g. The maximum output occurred at the resonance frequency and optimal load resistance, where the power conversion efficiency and electrical output power reached 48% and 290 W, respectively. Utilizing the resonance phenomenon was found to greatly enhance the performance of the wave energy converter, and there exists a maximum power point at the optimum load resistance.

  16. Synchronization analysis on cascaded multilevel converters with distributed control

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Cascaded multilevel converters built with integrated modules have many advantages such as increased power density,flexible distributed control, multi-functionality, increased reliability and short design cycles. However, the system performance will be affected due to the synchronization errors among each integrated modules. This paper analyzes the impact of the three kinds of synchronization errors on the whole system performance, as well as detailed synchronization implementation. Some valuable conclusions are derived from the theoretical analysis, simulations and experimental results.

  17. Identifier-based adaptive neural dynamic surface control for uncertain DC-DC buck converter system with input constraint

    Science.gov (United States)

    Chen, Qiang; Ren, Xuemei; Oliver, Jesus Angel

    2012-04-01

    In this paper, an identifier-based adaptive neural dynamic surface control (IANDSC) is proposed for the uncertain DC-DC buck converter system with input constraint. Based on the analysis of the effect of input constraint in the buck converter, the neural network compensator is employed to ensure the controller output within the permissible range. Subsequently, the constrained adaptive control scheme combined with the neural network compensator is developed for the buck converter with uncertain load current. In this scheme, a newly presented finite-time identifier is utilized to accelerate the parameter tuning process and to heighten the accuracy of parameter estimation. By utilizing the adaptive dynamic surface control (ADSC) technique, the problem of "explosion of complexity" inherently in the traditional adaptive backstepping design can be overcome. The proposed control law can guarantee the uniformly ultimate boundedness of all signals in the closed-loop system via Lyapunov synthesis. Numerical simulations are provided to illustrate the effectiveness of the proposed control method.

  18. Modules of systems of measures on polarizable Carnot groups

    Science.gov (United States)

    Brakalova, M.; Markina, I.; Vasil'ev, A.

    2016-10-01

    The paper presents a study of Fuglede's p-module of systems of measures in condensers in polarizable Carnot groups. In particular, we calculate the p-module of measures in spherical ring domains, find the extremal measures, and finally, extend a theorem by Rodin to these groups.

  19. On orthogonal systems in Hilbert C*-modules

    OpenAIRE

    Landi, Giovanni; PAVLOV, Alexander

    2009-01-01

    Analogues for Hilbert C*-modules of classical results of Fourier series theory in Hilbert spaces are considered. Relations between different properties of orthogonal and orthonormal systems for Hilbert C*-modules are studied with special attention paid on the differences with the well-known Hilbert space situation.

  20. 一种非反相Buck-Boost功率变换器的调制方法研究%Research on Modulation Method for Non-inverting Buck-Boost Power Converter

    Institute of Scientific and Technical Information of China (English)

    徐坤; 杨宇; 吴春华; 许富强

    2011-01-01

    针对功率变换器现有调制方法的不足,提出了一种用于非反相Buck-Boost功率变换器的调制方法,结合脉冲宽度调制和脉冲频率调制,使该功率变换器平滑地在Buck、Buck-Boost、Boost三种模式之间切换,从而在输入电压低于、高于或近似等于输出电压给定值的情况下,使输出电压稳定在给定电压.试验结果验证了该算法的可行性和有效性.%Aiming at the drawbacks of modulation method for power converter, a modulation method which combines pulse width modulation (PWM) with pulse frequency modulation (PFM) for the non-inverting buck-boost converter is proposed in the paper.The power converter can switch smoothly among buck working mode, buck boost working mode and boost working mode in order to regulate the output voltage to the desired output voltage regardless of that the input voltage is less than, greater than or equal to the desired output voltage.The experimental results verify the feasibility and efficiency of the proposed algorithm.