WorldWideScience

Sample records for conversion core redesign

  1. Conversion, core redesign and upgrade of the Rhode Island Atomic Energy Commission Reactor

    International Nuclear Information System (INIS)

    DiMeglio, A.F.

    1987-01-01

    The 2 MW Rhode Island Atomic Energy Commission reactor is required to convert from the use of High Enriched Uranium (HEU) fuel to the use of Low Enriched Uranium (LEU) fuel using a standard LEU fuel plate which is thinner and contains more Uranium-235 than the current HEU plate. These differences, coupled with the fact that the conversion should be accomplished without serious degradation of reactor characteristics and capability, has resulted in core design studies and thermal hydraulic studies not only at the current 2 MW but also at the maximum power level of the reactor, 5 MW. In addition, during the course of its 23 years of operation, it has become clear that the main uses of the reactor are neutron scattering and neutron activation analysis. The requirement to convert to LEU presents an opportunity during the conversion to optimize the core for the utilization and to restudy the thermal hydraulics using modern techniques. This paper will present the preliminary conclusions of both aspects. (Author)

  2. Core conversion effects on the safety analysis of research reactors

    International Nuclear Information System (INIS)

    Anoussis, J.N.; Chrysochoides, N.G.; Papastergiou, C.N.

    1982-07-01

    The safety related parameters of the 5 MW Democritus research reactor that will be affected by the scheduled core conversion to use LEU instead of HEU are considered. The analysis of the safety related items involved in such a core conversion, mainly the consequences due to MCA, DBA, etc., is of a general nature and can, therefore, be applied to other similar pool type reactors as well. (T.A.)

  3. Licensing procedures and safety criteria for core conversion in Japan

    International Nuclear Information System (INIS)

    Kanda, K.; Nakagome, Y.; Hayashi, M.

    1983-01-01

    Procedures relating to the construction and operation of reactor facilities are discussed. Specifically, the Safety Analysis Report on the Kyoto University Critical Assembly (KUCA) core conversion (93% to 45% enrichment) is noted. The results of critical experiments in the KUCA and of burnup tests in the Oak Ridge Research (ORR) Reactor will be used in the final determination of the feasibility of the conversion of the Kyoto University High Flux Reactor (KUHFR) to the use of 45% enrichment

  4. Study on HANARO core conversion using U-Mo fuel

    International Nuclear Information System (INIS)

    Lee, K.H.; Lee, C.S.; Seo, C.G.; Park, S.J.; Kim, H.; Kim, C.K.

    2002-01-01

    Two types of fuel rods with different fuel meat diameter and uranium density are considered for HANARO core conversion with high density U-Mo fuel. Arranging standard fuels of 5.0 g U/cc and 6.35 mm in diameter at the inner ring of an assembly and reduced fuels of 4.3 g U/cc and 5.49 mm in diameter at the outer ring of an assembly flattens the assembly power distribution and avoids the increase of linear heat generation rate due to using higher uranium density and less number of fuel rods. The maximum linear heat generation rate is similar with the current reference core and four fuel sites at the outer core in the reflector tank is converted to the irradiation sites to suit more demand on fuel tests and radioisotope production at outer core sites. This new core has 32% longer fuel cycle than the current reference core. (author)

  5. Review on JMTR safety design for LEU core conversion

    International Nuclear Information System (INIS)

    Komori, Yoshihiro; Yokokawa, Makoto; Saruta, Toru; Inada, Seiji; Sakurai, Fumio; Yamamoto, Katsumune; Oyamada, Rokuro; Saito, Minoru

    1993-12-01

    Safety of the JMTR was fully reviewed for the core conversion to low enriched uranium fuel. Fundamental policies for the JMTR safety design were reconsidered based on the examination guide for safety design of test and research reactors, and safety of the JMTR was confirmed. This report describes the safety design of the JMTR from the viewpoint of major functions for reactor safety. (author)

  6. Research reactor core conversion guidebook. V.1: Summary

    International Nuclear Information System (INIS)

    1992-04-01

    In view of the proliferation concerns caused by the use of highly enriched uranium (HEU) and in anticipation that the supply of HEU to research and test reactors will be more restricted in the future, this guidebook has been prepared to assist research reactor operators in addressing the safety and licensing issues for conversion of their reactor cores from the use of HEU fuel to the use of low enriched uranium fuel. This Guidebook, in five volumes, addresses the effects of changes in the safety-related parameters of mixed cores and the converted core. It provides an information base which should enable the appropriate approvals processes for implementation of a specific conversion proposal, whether for a light or for a heavy water moderated research reactor. Refs, figs, bibliographies and tabs

  7. Calculations in support of the MNR core conversion

    International Nuclear Information System (INIS)

    Day, S.E.; Butler, M.P.; Garland, Wm. J.

    2002-01-01

    Calculations and results in support of the HEU to LEU fuel conversion for the McMaster Nuclear Reactor are described. Static reactor physics studies were used to determine local and global power distributions; facilitating the definition of a Reference Core configuration for mixed HEU-LEU and complete LEU loadings. Fission product inventory calculations were used to compare the two fuel enrichments from a radiological hazard point of view. Thermalhydraulic models were created and analyzed to determine steady-state temperature distributions and safety margins, and used as a scoping tool the in development of a full core thermalhydraulic model. The behaviour of the two enrichment fuels was investigated in the context of a protected startup transient. The simulation results support the conclusion that the LEU fuel behaves in much the same way as the HEU fuel, which it is replacing. The conversion results in no new safety issues or significant changes in safety parameters. (author)

  8. Safety aspects of the RECH-1 core conversion

    International Nuclear Information System (INIS)

    Wetherby, Jaime Riesle

    1998-01-01

    When the RECH-1 research reactor joined the core conversion program for low enrichment fuel, the need to review some safety related aspects, which are currently under way with different degrees of progress, became apparent. The mentioned aspects can be grouped into: evaluation of the technical specifications of the new fuel elements: the technical specifications were carefully verified and contrasted with the recommendations of the IAEA and with those of manufacturers which are widely known for their expertise. (author)

  9. High enrichment to low enrichment core's conversion. Technical securities

    International Nuclear Information System (INIS)

    Abbate, P.; Madariaga, M.R.

    1990-01-01

    This work presents the fulfillment of the technical securities subscribed by INVAP S.E. for the conversion of a high enriched uranium core. The reactor (of 5 thermal Mw), built in the 50's and 60's, is of the 'swimming pool' type, with light water and fuel elements of the curve plates MTR type, enriched at 93.15 %. These are neutronic and thermohydraulic securities. (Author) [es

  10. Licensing procedures and safety criteria for core conversion in Japan

    International Nuclear Information System (INIS)

    Kanda, K.; Nakagome, Y.; Hayashi, M.

    1983-01-01

    In Japan, the establishment and operation of nuclear installations are governed mainly by the Law for Regulation of Nuclear Source Material, Nuclear Fuel Material and Reactors. This law lays down the regulations and conditions for licensing of the various installations involved in the nuclear fuel cycle, namely licensing of installations for refining, fabricating and reprocessing; and reactors, as well as licensing of the use of nuclear fuels in research facilities. Although procedures for the installations listed above vary depending on the installation concerned, only those relating to construction and operation of reactor facilities will be analysed in this study, as the conditions and principles applying to licensing and control of other installations are, to a large extent, similar to those concerning reactor facilities. The second part of this presentation describes the safety review of the KUCA reactor core conversion form HEU to MEU. For the safety review of the core conversion, the Committee on Examination of Reactor Safety of Japanese Government examined mainly the the nuclear characteristics and the integrity of aluminide fuel plates, which was very severe because we had no experience to use aluminide fuel plates in Japan. The integrity of fuel plates and the results of the worst accident analysis for the MEU core are shown with the comparison between the HEU and MEU cores. The significant difference was not observed between them. All the regulatory procedures were completed in September 1980. Fabrication of MEU fuel elements for the KUCA experiments by CERCA in France was started in September 1980, and will be completed in March 1981. The critical experiments in the KUCA with MEU fuel will be started on a single-core in May 1981 as a first step. Those on a coupled-core will follow

  11. Neutronic design of mixed oxide-silicide cores for the core conversion of rsg-gas reactor

    International Nuclear Information System (INIS)

    Sembiring, Tagor Malem; Tukiran; Pinem surian; Febrianto

    2001-01-01

    The core conversion of rsg-gas reactor from an all-oxide (U 3 O 8 -Al) core, through a series of mixed oxide-silicide core, to an all-silicide (U 3 Si 2 -Al) core for the same meat density of 2.96 g U/cc is in progress. The conversion is first step of the step-wise conversion and will be followed by the second step that is the core conversion from low meat density of silicide core, through a series of mixed lower-higher density of silicide core, to an all-higher meat density of 3.55 g/cc core. Therefore, the objectives of this work is to design the mixed cores on the neutronic performance to achieve safety a first full-silicide core for the reactor with the low uranium meat density of 2.96gU/cc. The neutronic design of the mixed cores was performed by means of Batan-EQUIL-2D and Batan-3DIFF computer codes for 2 and 3 dimension diffusion calculation, respectively. The result shows that all mixed oxide-silicide cores will be feasible to achieve safety a fist full-silicide core. The core performs the same neutronic core parameters as those of the equilibrium silicide core. Therefore, the reactor availability and utilization during the core conversion is not changed

  12. High enrichment to low enrichment core's conversion. Accidents analysis

    International Nuclear Information System (INIS)

    Abbate, P.; Rubio, R.; Doval, A.; Lovotti, O.

    1990-01-01

    This work analyzes the different accidents that may occur in the reactor's facility after the 20% high-enriched uranium core's conversion. The reactor (of 5 thermal Mw), built in the 50's and 60's, is of the 'swimming pool' type, with light water and fuel elements of the curve plates MTR type, enriched at 93.15 %. This analysis includes: a) accidents by reactivity insertion; b) accidents by coolant loss; c) analysis by flow loss and d) fission products release. (Author) [es

  13. Neutronic characteristics of FLWR in the transition phase changing from high conversion core to breeder core

    International Nuclear Information System (INIS)

    Akie, Hiroshi; Nakano, Yoshihiro; Okubo, Tsutomu

    2009-01-01

    Innovative Water Reactor for Flexible Fuel Cycle (FLWR) is a low moderation type boiling water reactor which can realize plutonium multiple recycling and breeding. For the introduction stage of FLWR, a high conversion (HC) type FLWR is proposed to keep technical continuity from current light water reactors. The HC core of FLWR has a less tight fuel lattice with lower coolant void fraction than the breeder (BR) type core. The HC type FLWR core is to be shifted to the BR core by only replacing the fuel assemblies of the same outer shape and size in the same reactor system. In the HC to BR transition phase of FLWR, there exist both types of fuel assemblies in the same core configuration. In the HC assembly, neutron spectrum is softer than in the BR assembly, and the axial fuel and blanket arrangement is different from the BR assembly. Due to these differences, there might appear a power peaking in the adjacent region between HC and BR assemblies. The power distribution in the HC + BR assemblies mixed core configuration is studied by performing assembly calculations and core calculations on a few assemblies local geometry and the whole core geometry. As a result, although a power peaking can be locally very large in the HC and BR assemblies adjacent regions, such local power peakings are shown to be effectively reduced by considering a rod-wise fuel enrichment distribution. In the whole core calculation, it seems possible to optimize the fuel assembly loading and shuffling pattern to avoid large power level mismatch between the assemblies. It is expected that FLWR can be shifted from HC type to BR type without major neutronic difficulties. (author)

  14. Core instrumentation and pre-operational procedures for core conversion HEU to LEU

    International Nuclear Information System (INIS)

    1984-02-01

    This report is intended for the reactor operator, to be used as a manual or checklist for general guidance on pre-startup activities that need to be addressed in preparation for conversion to Low Enriched Fuel (LEU). All nuclear, thermodynamic and safety calculations should have been performed prior to this stage of the core conversion process. During these calculations and certainly before ordering the new LEU fuel elements the reactor operator needs to very carefully consider additional important factors concerning the new fuel: fuel reliability, reliability of fuel fabricator, reprocessing contract or fuel element storage and disposal, economics of the new fuel cycle. At this stage, too, a preoperational experimental programme has to be developed and presented to the regulatory authorities for approval. This experimental programme could lead to additional requirements on: in-core instrumentation, out-of-core instrumentation or additional experimental devices. Detailed instructions on specific tests and measurements are not provided in this report since much information on the subject is available in the open literature

  15. Research reactor core conversion programmes, Department of Research and Isotopes, International Atomic Energy Agency

    International Nuclear Information System (INIS)

    Muranaka, R.G.

    1985-01-01

    In order to put the problem of core conversion into perspective, statistical information on research reactors on a global scale is presented (from IAEA Research reactor Data Base). This paper describes the research reactor core conversion program of the Department of Research and Isotopes. Technical committee Meetings were held on the subject of research reactor core conversion since 1978, and results of these meetings are published in TECDOC-233, TECDOC-324, TECDOC-304. Additional publications are being prepared, several missions of experts have visited countries to discuss and help to plan core conversion programs; training courses and seminars were organised; IAEA has supported attendance of participants from developing countries to RERTR Meetings

  16. The HOR core conversion program development and licensing experiences

    International Nuclear Information System (INIS)

    Vries, J.W. de; Gibcus, H.P.M.; Leege, P.F.A. de

    1997-01-01

    This paper deals with the experiences in the development of a fuel conversion program for a 2 MW university type research reactor, the HOR. It gives an overview of the technical and administrative aspects concerning the fuel conversion program development since the eighties, including the safety review and licensing process. The overall final safety report was submitted in 1995, together with the environmental impact report, and a licence application was submitted accordingly. The licence permitting the conversion was issued in 1996, coming into force at the beginning of this year, although an appeal case is still pending. At the moment the necessary preparations for starting the actual conversion of the HOR are made. The general program characteristics are addressed. (author)

  17. Redesign workshop

    DEFF Research Database (Denmark)

    Bornoe, Nis; Billestrup, Jane; Andersen, Jesper

    2014-01-01

    . The leading question was: “Can software developers contribute actively to alternative redesign suggestions?” Under the guidance of usability specialists, we found that the developers were able to constructively reconsider the existing design based on a top down approach. In this paper we report a hands...

  18. Fast neutrino flavor conversions near the supernova core with realistic flavor-dependent angular distributions

    Energy Technology Data Exchange (ETDEWEB)

    Dasgupta, Basudeb; Sen, Manibrata [Tata Institute of Fundamental Research, Homi Bhabha Road, Mumbai, 400005 (India); Mirizzi, Alessandro, E-mail: bdasgupta@theory.tifr.res.in, E-mail: alessandro.mirizzi@ba.infn.it, E-mail: manibrata.sen@gmail.com [Dipartimento Interateneo di Fisica ' Michelangelo Merlin' , Via Amendola 173, 70126 Bari (Italy)

    2017-02-01

    It has been recently pointed out that neutrino fluxes from a supernova can show substantial flavor conversions almost immediately above the core. Using linear stability analyses and numerical solutions of the fully nonlinear equations of motion, we perform a detailed study of these fast conversions , focussing on the region just above the supernova core. We carefully specify the instabilities for evolution in space or time, and find that neutrinos travelling towards the core make fast conversions more generic, i.e., possible for a wider range of flux ratios and angular asymmetries that produce a crossing between the zenith-angle spectra of ν {sub e} and ν-bar {sub e} . Using fluxes and angular distributions predicted by supernova simulations, we find that fast conversions can occur within tens of nanoseconds, only a few meters away from the putative neutrinospheres. If these fast flavor conversions indeed take place, they would have important implications for the supernova explosion mechanism and nucleosynthesis.

  19. LOGOS. HX: a core simulator for high conversion boiling water reactors

    International Nuclear Information System (INIS)

    Tsuiki, Makoto; Sakurada, Koichi; Yoshida, Hiroyuki.

    1988-01-01

    A three-dimensional physics simulator 'LOGOS. HX' has been developed for the designing analysis of high conversion boiling water reactor (HCBWR) cores. Its functions, calculational methods, and verification results will briefly be discussed. (author)

  20. Effects of conversion ratio change on the core performances in medium to large TRU burning reactors

    International Nuclear Information System (INIS)

    Song, Hoon; Kim, Sang-Ji; Yoo, Jae-Woon; Kim, Yeong-Il

    2009-01-01

    Conceptual fast reactor core designs with sodium coolant are developed at 1,500, 3,000 and 4,500 MWt which are configured to transmute recycled transuranics (TRU) elements with external feeds consisting of LWR spent fuel. Even at each pre-determined power level, the performance parameters, reactivity coefficients and their implications on the safety analysis can be different when the target TRU conversion ratio changes. In order to address this aspect of design, a study on TRU conversion ratio change was performed. The results indicate that it is feasible to design a TRU burner core to accommodate a wide range of conversion ratios by employing different fuel cladding thicknesses. The TRU consumption rate is found to be proportional to the core power without any significant deterioration in the core performance at higher power levels. A low conversion ratio core has an increased TRU consumption rate and much faster burnup reactivity loss, which calls for appropriate means for reactivity compensation. As for the reactivity coefficients related with the conversion ratio change, the core with a low conversion ratio has a less negative Doppler coefficient, a more negative axial expansion coefficient, a more negative control rod worth per rod, a more negative radial expansion coefficient, a less positive sodium density coefficient and a less positive sodium void worth. A slight decrease in the delayed neutron fraction is also noted, reflecting the fertile U-238 fraction reduction. (author)

  1. Refurbishment, core conversion and safety analysis of Apsara reactor

    Energy Technology Data Exchange (ETDEWEB)

    Raina, V.K.; Sasidharan, K.; Sengupta, S. [Bhabha Atomic Research Centre, Mumbai (India)]. E-mail: nram@@apsara.barc.ernet.in

    1998-07-01

    Apsara, a 1 MWt pool type reactor using HEU fuel has been in operation at the Bhabha Atomic Research Centre, Trombay since 1956. In view of the long service period seen by the reactor it is now planned to carry out extensive refurbishment of the reactor with a view to extend its useful life. It is also proposed to modify the design of the reactor wherein the core will be surrounded by a heavy water reflector tank to obtain a good thermal neutron flux over a large radial distance from the core. Beam holes and the majority of the irradiation facilities will be located inside the reflector tank. The coolant flow direction through the core will be changed from the existing upward flow to downward flow. A delay tank, located inside the pool, is provided to facilitate decay of short lived radioactivity in the coolant outlet from the core in order to bring down radiation field in the operating areas. Analysis of various anticipated operational occurrences and accident conditions like loss of normal power, core coolant flow bypass, fuel channel blockage and degradation of primary coolant pressure boundary have been performed for the proposed design. Details of the proposed design modifications and the safety analyses are given in the paper. (author)

  2. Core conversion anaylses for the Portuguese Research Reactor

    International Nuclear Information System (INIS)

    Matos, J.E.; Stevens, J.G.; Feldman, E.E.; Stillman, J.A.; Dunn, F.E.; Kalimullah, K.; Marques, J.G.; Barradas, N.P.; Ramos, A.R.; Kling, A.

    2006-01-01

    Design and safety analyses are presented for conversion of the Portuguese Research Reactor (RPI) from the use of HEU fuel to the use of LEU fuel. The analyses were performed jointly by the RERTR Program at the Argonne National Laboratory (ANL) and the Instituto Tecnologico e Nuclear (ITN). The LEU fuel assembly design uses U 3 Si 2 -Al dispersion fuel with 4.8 g U/cm 3 and is very similar to the HEU fuel design. The results of neutronic studies, steady-state thermal-hydraulic analyses, accident analyses, and revisions to the Operating Limits and Conditions demonstrate that the RPI reactor can be operated safely with the new LEU fuel assemblies. Delivery of the LEU fuel is expected around the end of 2006, with conversion in early 2007. The HEU fuel is planned to be returned to the US in 2008.

  3. A mixed core conversion study with HEU and LEU fuels

    International Nuclear Information System (INIS)

    Matos, J.E.; Freese, K.E.

    1985-01-01

    The results of a mixed core study are presented for gradual replacement of HEU fuel with LEU fuel using the IAEA generic 10 MW reactor as an example. The key parameters show that the transition can be accomplished safely and economically. (author)

  4. Mixed core conversion study with HEU and LEU fuels

    International Nuclear Information System (INIS)

    Matos, J.E.; Freese, K.E.

    1984-01-01

    The results of a mixed core study are presented for gradual replacement of HEU fuel with LEU fuel using the IAEA generic 10 MW reactor as an example. The key parameters show that the transition can be accomplished safely and economically

  5. Turkey's regulatory plans for high enriched to low enriched conversion of TR-2 reactor core

    International Nuclear Information System (INIS)

    Guelol Oezdere, Oya

    2003-01-01

    Turkey is a developing country and has three nuclear facilities two of which are research reactors and one pilot fuel production plant. One of the two research reactors is TR-2 which is located in Cekmece site in Istanbul. TR-2 Reactor's core is composed of both high enriched and low enriched fuel and from high enriched to low enriched core conversion project will take place in year 2005. This paper presents the plans for drafting regulations on the safety analysis report updates for high enriched to low enriched core conversion of TR-2 reactor, the present regulatory structure of Turkey and licensing activities of nuclear facilities. (author)

  6. The Core Conversion of the TRIGA Reactor Vienna

    International Nuclear Information System (INIS)

    Villa, M.; Bergmann, R.; Musilek, A.; Sterba, J.H.; Böck, H.; Messick, C.

    2016-01-01

    The TRIGA Reactor Vienna has operated for many years with a mixed core using Al-clad and stainless-steel (SST) clad low enriched uranium (LEU) fuel and a few SST high enriched uranium (HEU) fuel elements. In view of the US spent fuel return program, the average age of these fuel elements and the Austrian position not to store any spent nuclear fuel on its territory, negotiation started in April 2011 with the US Department of Energy (DOE) and the International Atomic Energy Agency (IAEA). The sensitive subject was to return the old TRIGA fuel and to find a solution for a possible continuation of reactor operation for the next decades. As the TRIGA Vienna is the closest nuclear facility to the IAEA headquarters, high interest existed at the IAEA to have an operating research reactor nearby, as historically close cooperation exists between the IAEA and the Atominstitut. Negotiation started before summer 2011 between the involved Austrian ministries, the IAEA and the US DOE leading to the following solution: Austria will return 91 spent fuel elements to the Idaho National Laboratory (INL) while INL offers 77 very low burnt SST clad LEU elements for further reactor operation of the TRIGA reactor Vienna. The titles of these 77 new fuel elements will be transferred to Euratom in accordance with Article 86 of the Euratom-US Treaty. The fuel exchange with the old core returned to the INL, and the new core transferred to Vienna was carried out in one shipment in late 2012 through the ports of Koper/Slovenia and Trieste/Italy. This paper describes the administrative, logistic and technical preparations of the fuel exchange being unique world-wide and first of its kind between Austria and the USA performed successfully in early November 2012. (author)

  7. Safety And Transient Analyses For Full Core Conversion Of The Dalat Nuclear Research Reactor

    International Nuclear Information System (INIS)

    Luong Ba Vien; Le Vinh Vinh; Huynh Ton Nghiem; Nguyen Kien Cuong

    2011-01-01

    Preparing for full core conversion of Dalat Nuclear Research Reactor (DNRR), safety and transient analyses were carried out to confirm about ability to operate safely of proposed Low Enriched Uranium (LEU) working core. The initial LEU core consisting 92 LEU fuel assemblies and 12 Beryllium rods was analyzed under initiating events of uncontrolled withdrawal of a control rod, cooling pump failure, earthquake and fuel cladding fail. Working LEU core response were evaluated under these initial events based on RELAP/Mod3.2 computer code and other supported codes like ORIGEN, MCNP and MACCS2. Obtained results showed that safety of the reactor is maintained for all transients/accidents analyzed. (author)

  8. Single-mode fiber laser based on core-cladding mode conversion.

    Science.gov (United States)

    Suzuki, Shigeru; Schülzgen, Axel; Peyghambarian, N

    2008-02-15

    A single-mode fiber laser based on an intracavity core-cladding mode conversion is demonstrated. The fiber laser consists of an Er-doped active fiber and two fiber Bragg gratings. One Bragg grating is a core-cladding mode converter, and the other Bragg grating is a narrowband high reflector that selects the lasing wavelength. Coupling a single core mode and a single cladding mode by the grating mode converter, the laser operates as a hybrid single-mode laser. This approach for designing a laser cavity provides a much larger mode area than conventional large-mode-area step-index fibers.

  9. Design study of eventual core conversion for the research reactor RA

    International Nuclear Information System (INIS)

    Matausek, M. V.; Marinkovic, N.

    1998-01-01

    Main options are specified for the future status of the 6.5 MW heavy water research reactor RA. Arguments pro and contra restarting the reactor are presented. When considering the option to restart the RA reactor, possibilities to improve its neutronic parameters, such as neutron flux values and irradiation capabilities are discussed, as well as the compliance with the worldwide activities of Reduced Enrichment for Research and Test Reactors (RERTR) program. Possibility of core conversion is examined. Detailed reactor physics design calculations are performed for different fuel types and uranium loading. For different fuel management schemes results are presented for the effective, multiplication factor, power distribution, fuel burnup and consumption. It is shown that, as far as reactor core parameters are considered, conversion to lower enrichment fuel could be easily accomplished. However, conversion to the lower enrichment could only be justified if combined with improvement of some other reactor attributes. (author)

  10. Reactor core conversion studies of Ghana: Research Reactor-1 and proposal for addition of safety rod

    International Nuclear Information System (INIS)

    Odoi, H.C.

    2014-06-01

    The inclusion of an additional safety rod in conjunction with a core conversion study of Ghana Research Reactor-1 (GHARR-1) was carried out using neutronics, thermal hydraulics and burnup codes. The study is based on a recommendation by Integrated Safety Assessment for Research Reactors (INSARP) mission to incorporate a safety rod to the reactor safety system as well as the need to replace the reactor fuel with LEU. Conversion from one fuel type to another requires a complete re-evaluation of the safety analysis. Changes to the reactivity worth, shutdown margin, power density and material properties must be taken into account, and appropriate modifications made. Neutronics analysis including burnup was studied followed by thermal hydraulics analyses which comprise steady state and transients. Four computer codes were used for the analysis; MCNP, REBUS, PLTEP and PARET. The neutronics analysis revealed that the LEU core must be operated at 34 Kw in order to attain the flux of 1.0E12 n/cm 2 .s as the nominal flux of the HEU core. The auxiliary safety rod placed at a modified irradiation site gives a better worth than the cadmium capsules. For core excess reactivity of 4 mk, 348 fuel pins would be appropriate for the GHARR-1 LEU core. Results indicate that flux level of 1.0E12 n/cm 2 .s in the inner irradiation channel will not be compromised, if the power of the LEU core is increased to 34 kW. The GHARR-1 core using LEU-U0 2 -12.5% fuel can be operated for 23 shim cycles, with cycles length 2.5 years, for over 57 years at the 17 kW power level. All 23 LEU cycles meet the ∼ 4.0 mk excess reactivity required at the beginning of cycle . For comparison, the MNSR HEU reference core can also be operated for 23 shim cycles, but with a cycle length of 2.0 years for just over 46 years at 15.0kW power level. It is observed that the GHARR-1 core with LEU UO 2 fuel enriched to 12.5% and a power level of 34 kW can be operated ∼25% longer than the current HEU core operated at

  11. Research reactor core conversion guidebook. V.2: Analysis (Appendices A-F)

    International Nuclear Information System (INIS)

    1992-04-01

    Volume 2 consists of detailed Appendices, covering safety analyses for generic 10 MW reactor, safety analysis - probabilistic methods, methods for preventing LOCA, radiological consequence analyses, examples of safety report amendments and safety specifications. Included in Volume 2 are example analyses for cores with with highly enriched uranium and low enriched uranium fuels showing differences that can be expected in the safety parameters and radiological consequences of postulated accidents. There are seven examples of licensing documents related to core conversion and two examples of methods for determining power limits for safety specifications in the document. Refs, figs, bibliographies and tabs

  12. HEU core conversion of Russian production reactors: a major threat to the international RERTR regime

    International Nuclear Information System (INIS)

    Kuperman, Alan J.; Leventhal, Paul L.

    1998-01-01

    This paper calls the attention for the major threat to the International Reduced Enrichment for Research and Test Reactors (RERTR) program, represented by the HEU core conversion of russian production reactors. This program aims to reduce and eventually eliminate international civilian commerce in nuclear weapons-usable, highly enriched uranium , and thereby significantly lower risks of the material being stolen or diverted by terrorist or states for producing nuclear weapons

  13. Development of suspended core soft glass fibers for far-detuned parametric conversion

    Science.gov (United States)

    Rampur, Anupamaa; Ciąćka, Piotr; Cimek, Jarosław; Kasztelanic, Rafał; Buczyński, Ryszard; Klimczak, Mariusz

    2018-04-01

    Light sources utilizing χ (2) parametric conversion combine high brightness with attractive operation wavelengths in the near and mid-infrared. In optical fibers, it is possible to use χ (3) degenerate four-wave mixing in order to obtain signal-to-idler frequency detuning of over 100 THz. We report on a test series of nonlinear soft glass suspended core fibers intended for parametric conversion of 1000-1100 nm signal wavelengths available from an array of mature lasers into the near-to-mid-infrared range of 2700-3500 nm under pumping with an erbium sub-picosecond laser system. The presented discussion includes modelling of the fiber properties, details of their physical development and characterization, and experimental tests of parametric conversion.

  14. Core design options for high conversion BWRs operating in Th–233U fuel cycle

    International Nuclear Information System (INIS)

    Shaposhnik, Y.; Shwageraus, E.; Elias, E.

    2013-01-01

    Highlights: • BWR core operating in a closed self-sustainable Th– 233 U fuel cycle. • Seed blanket optimization that includes assembly size array and axial dimensions. • Fully coupled MC with fuel depletion and thermo-hydraulic feedback modules. • Thermal-hydraulic analysis includes MCPR observation. -- Abstract: Several options of fuel assembly design are investigated for a BWR core operating in a closed self-sustainable Th– 233 U fuel cycle. The designs rely on an axially heterogeneous fuel assembly structure consisting of a single axial fissile zone “sandwiched” between two fertile blanket zones, in order to improve fertile to fissile conversion ratio. The main objective of the study was to identify the most promising assembly design parameters, dimensions of fissile and fertile zones, for achieving net breeding of 233 U. The design challenge, in this respect, is that the fuel breeding potential is at odds with axial power peaking and the core minimum critical power ratio (CPR), hence limiting the maximum achievable core power rating. Calculations were performed with the BGCore system, which consists of the MCNP code coupled with fuel depletion and thermo-hydraulic feedback modules. A single 3-dimensional fuel assembly having reflective radial boundaries was modeled applying simplified restrictions on the maximum centerline fuel temperature and the CPR. It was found that axially heterogeneous fuel assembly design with a single fissile zone can potentially achieve net breeding, while matching conventional BWR core power rating under certain restrictions to the core loading pattern design

  15. Technical basis in support of the conversion of the University of Missouri Research Reactor (MURR) core from highly-enriched to low-enriched uranium - core neutron physics

    Energy Technology Data Exchange (ETDEWEB)

    Stillman, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Feldman, E. [Univ. of Missouri, Columbia, MO (United States). Columbia Research Reactor; Foyto, L [Univ. of Missouri, Columbia, MO (United States). Columbia Research Reactor; Kutikkad, K [Univ. of Missouri, Columbia, MO (United States). Columbia Research Reactor; McKibben, J C [Univ. of Missouri, Columbia, MO (United States). Columbia Research Reactor; Peters, N. [Univ. of Missouri, Columbia, MO (United States). Columbia Research Reactor; Stevens, J. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2012-09-01

    This report contains the results of reactor design and performance for conversion of the University of Missouri Research Reactor (MURR) from the use of highly-enriched uranium (HEU) fuel to the use of low-enriched uranium (LEU) fuel. The analyses were performed by staff members of the Global Threat Reduction Initiative (GTRI) Reactor Conversion Program at the Argonne National Laboratory (ANL) and the MURR Facility. The core conversion to LEU is being performed with financial support of the U. S. government.

  16. Status of core conversion with LEU silicide fuel in JRR-4

    Energy Technology Data Exchange (ETDEWEB)

    Nakajima, Teruo; Ohnishi, Nobuaki; Shirai, Eiji [Japan Atomic Energy Research Institute, Ibaraki-ken (Japan)

    1997-08-01

    Japan Research Reactor No.4 (JRR-4) is a light water moderated and cooled, 93% enriched uranium ETR-type fuel used and swimming pool type reactor with thermal output of 3.5MW. Since the first criticality was achieved on January 28, 1965, JRR-4 has been used for shielding experiments, radioisotope production, neutron activation analyses, training for reactor engineers and so on for about 30 years. Within the framework of the RERTR Program, the works for conversion to LEU fuel are now under way, and neutronic and thermal-hydraulic calculations emphasizing on safety and performance aspects are being carried out. The design and evaluation for the core conversion are based on the Guides for Safety Design and Evaluation of research and testing reactor facilities in Japan. These results show that the JRR-4 will be able to convert to use LEU fuel without any major design change of core and size of fuel element. LEU silicide fuel (19.75%) will be used and maximum neutron flux in irradiation hole would be slightly decreased from present neutron flux value of 7x10{sup 13}(n/cm{sup 2}/s). The conversion works are scheduled to complete in 1998, including with upgrade of the reactor building and utilization facilities.

  17. Status of core conversion with LEU silicide fuel in JRR-4

    International Nuclear Information System (INIS)

    Nakajima, Teruo; Ohnishi, Nobuaki; Shirai, Eiji

    1997-01-01

    Japan Research Reactor No.4 (JRR-4) is a light water moderated and cooled, 93% enriched uranium ETR-type fuel used and swimming pool type reactor with thermal output of 3.5MW. Since the first criticality was achieved on January 28, 1965, JRR-4 has been used for shielding experiments, radioisotope production, neutron activation analyses, training for reactor engineers and so on for about 30 years. Within the framework of the RERTR Program, the works for conversion to LEU fuel are now under way, and neutronic and thermal-hydraulic calculations emphasizing on safety and performance aspects are being carried out. The design and evaluation for the core conversion are based on the Guides for Safety Design and Evaluation of research and testing reactor facilities in Japan. These results show that the JRR-4 will be able to convert to use LEU fuel without any major design change of core and size of fuel element. LEU silicide fuel (19.75%) will be used and maximum neutron flux in irradiation hole would be slightly decreased from present neutron flux value of 7x10 13 (n/cm 2 /s). The conversion works are scheduled to complete in 1998, including with upgrade of the reactor building and utilization facilities

  18. The status of HEU to LEU core conversion activities at the Jamaica SLOWPOKE

    Energy Technology Data Exchange (ETDEWEB)

    Preston, J.; Grant, C., E-mail: john.preston@uwimona.edu.jm [Univ. of the West Indies, Mona Campus, International Centre for Environmental and Nuclear Sciences, Mona (Jamaica)

    2012-12-15

    The SLOWPOKE reactor in Jamaica has been operated by the International Centre for Environmental and Nuclear Sciences, University of the West Indies since 1984, mainly for the purpose of Neutron Activation Analysis. The HEU core with current utilization has another 14 years of operation, before the addition of a large beryllium annulus would be required to further extend the life-time by 15 years. However, in keeping with the spirit of the Reduced Enrichment for Research and Test Reactors (RERTR) program, the decision was taken in 2003 to convert the core from HEU to LEU, in line with those at the Ecole Polytechnic and RMC SLOWPOKE facilities. This paper reports on the current status of the conversion activities, including key fuel manufacture and regulatory issues, which have seen substantial progress during the last year. A timetable for the complete process is given, and provided that the fuel fabrication can be completed in the estimated 18 months, the core conversion should be accomplished by the end of 2014. (author)

  19. The status of HEU and LEU core conversion activities at the Jamaica SLOWPOKE

    Energy Technology Data Exchange (ETDEWEB)

    Preston, J.; Grant, C., E-mail: john.preston@uwimona.edu.jm [Univ. of the West Indies, Mona Campus, International Centre for Environmental and Nuclear Sciences, Kingston (Jamaica)

    2013-07-01

    The SLOWPOKE reactor in Jamaica has been operated by the International Centre for Environmental and Nuclear Sciences, University of the West Indies since 1984, mainly for the purpose of Neutron Activation Analysis. The HEU core with current utilization has another 14 years of operation, before the addition of a large beryllium annulus would be required to further extend the life-time by 15 years. However, in keeping with the spirit of the Reduced Enrichment for Research and Test Reactors (RERTR) program, the decision was taken in 2003 to convert the core from HEU to LEU, inline with those at the Ecole Polytechnic and RMC SLOWPOKE facilities. This paper reports on the current status of the conversion activities, including key fuel manufacture and regulatory issues, which have seen substantial progress during the last year. A timetable for the complete process is given, and provided that the fuel fabrication can be completed in the estimated 18 months, the core conversion should be accomplished by the end of 2014. (author)

  20. Neutronic analysis for core conversion (HEU–LEU of the low power research reactor using the MCNP4C code

    Directory of Open Access Journals (Sweden)

    Aldawahra Saadou

    2015-06-01

    Full Text Available Comparative studies for conversion of the fuel from HEU to LEU in the miniature neutron source reactor (MNSR have been performed using the MCNP4C code. The HEU fuel (UAl4-Al, 90% enriched with Al clad and LEU (UO2 12.6% enriched with zircaloy-4 alloy clad cores have been analyzed in this study. The existing HEU core of MNSR was analyzed to validate the neutronic model of reactor, while the LEU core was studied to prove the possibility of fuel conversion of the existing HEU core. The proposed LEU core contained the same number of fuel pins as the HEU core. All other structure materials and dimensions of HEU and LEU cores were the same except the increase in the radius of control rod material from 0.195 to 0.205 cm and keeping the outer diameter of the control rod unchanged in the LEU core. The effective multiplication factor (keff, excess reactivity (ρex, control rod worth (CRW, shutdown margin (SDM, safety reactivity factor (SRF, delayed neutron fraction (βeff and the neutron fluxes in the irradiation tubes for the existing and the potential LEU fuel were investigated. The results showed that the safety parameters and the neutron fluxes in the irradiation tubes of the LEU fuels were in good agreements with the HEU results. Therefore, the LEU fuel was validated to be a suitable choice for fuel conversion of the MNSR in the future.

  1. Process design and redesign

    NARCIS (Netherlands)

    Reijers, H.A.; Dumas, M.; Aalst, van der W.M.P.; Hofstede, ter A.H.M.

    2005-01-01

    This chapter aims to provide concrete guidance in redesigning business processes. Two alternative methods are described, both of them suitable to boost business performance. The first one is based on a collection of best practices, as applied in various redesign projects. These best practices all

  2. Selection and benchmarking of computer codes for research reactor core conversions

    Energy Technology Data Exchange (ETDEWEB)

    Yilmaz, Emin [School of Aerospace, Mechanical and Nuclear Engineering, University of Oklahoma, Norman, OK (United States); Jones, Barclay G [Nuclear Engineering Program, University of IL at Urbana-Champaign, Urbana, IL (United States)

    1983-09-01

    A group of computer codes have been selected and obtained from the Nuclear Energy Agency (NEA) Data Bank in France for the core conversion study of highly enriched research reactors. ANISN, WIMSD-4, MC{sup 2}, COBRA-3M, FEVER, THERMOS, GAM-2, CINDER and EXTERMINATOR were selected for the study. For the final work THERMOS, GAM-2, CINDER and EXTERMINATOR have been selected and used. A one dimensional thermal hydraulics code also has been used to calculate temperature distributions in the core. THERMOS and CINDER have been modified to serve the purpose. Minor modifications have been made to GAM-2 and EXTERMINATOR to improve their utilization. All of the codes have been debugged on both CDC and IBM computers at the University of IL. IAEA 10 MW Benchmark problem has been solved. Results of this work has been compared with the IAEA contributor's results. Agreement is very good for highly enriched fuel (HEU). Deviations from IAEA contributor's mean value for low enriched fuel (LEU) exist but they are small enough in general. Deviation of k{sub eff} is about 0.5% for both enrichments at the beginning of life (BOL) and at the end of life (EOL). Flux ratios deviate only about 1.5% from IAEA contributor's mean value. (author)

  3. Progress in the neutronic core conversion (HEU-LEU) analysis of Ghana research reactor-1.

    Energy Technology Data Exchange (ETDEWEB)

    Anim-Sampong, S.; Maakuu, B. T.; Akaho, E. H. K.; Andam, A.; Liaw, J. J. R.; Matos, J. E.; Nuclear Engineering Division; Ghana Atomic Energy Commission; Kwame Nkrumah Univ. of Science and Technology

    2006-01-01

    The Ghana Research Reactor-1 (GHARR-1) is a commercial version of the Miniature Neutron Source Reactor (MNSR) and has operated at different power levels since its commissioning in March 1995. As required for all nuclear reactors, neutronic and thermal hydraulic analysis are being performed for the HEU-LEU core conversion studies of the Ghana Research Reactor-1 (GHARR-1) facility, which is a commercial version of the Miniature Neutron Source Reactor (MNSR). Stochastic Monte Carlo particle transport methods and tools (MCNP4c/MCNP5) were used to fine-tune a previously developed 3-D MCNP model of the GHARR-1 facility and perform neutronic analysis of the 90.2% HEU reference and candidate LEU (UO{sub 2}, U{sub 3}Si{sub 2}, U-9Mo) fresh cores with varying enrichments from 12.6%-19.75%. In this paper, the results of the progress made in the Monte Carlo neutronic analysis of the HEU reference and candidate LEU fuels are presented. In particular, a comparative performance assessment of the LEU with respect to neutron flux variations in the fission chamber and experimental irradiation channels are highlighted.

  4. Selection and benchmarking of computer codes for research reactor core conversions

    International Nuclear Information System (INIS)

    Yilmaz, Emin; Jones, Barclay G.

    1983-01-01

    A group of computer codes have been selected and obtained from the Nuclear Energy Agency (NEA) Data Bank in France for the core conversion study of highly enriched research reactors. ANISN, WIMSD-4, MC 2 , COBRA-3M, FEVER, THERMOS, GAM-2, CINDER and EXTERMINATOR were selected for the study. For the final work THERMOS, GAM-2, CINDER and EXTERMINATOR have been selected and used. A one dimensional thermal hydraulics code also has been used to calculate temperature distributions in the core. THERMOS and CINDER have been modified to serve the purpose. Minor modifications have been made to GAM-2 and EXTERMINATOR to improve their utilization. All of the codes have been debugged on both CDC and IBM computers at the University of IL. IAEA 10 MW Benchmark problem has been solved. Results of this work has been compared with the IAEA contributor's results. Agreement is very good for highly enriched fuel (HEU). Deviations from IAEA contributor's mean value for low enriched fuel (LEU) exist but they are small enough in general. Deviation of k eff is about 0.5% for both enrichments at the beginning of life (BOL) and at the end of life (EOL). Flux ratios deviate only about 1.5% from IAEA contributor's mean value. (author)

  5. Selection and benchmarking of computer codes for research reactor core conversions

    International Nuclear Information System (INIS)

    Yilmaz, E.; Jones, B.G.

    1983-01-01

    A group of computer codes have been selected and obtained from the Nuclear Energy Agency (NEA) Data Bank in France for the core conversion study of highly enriched research reactors. ANISN, WIMSD-4, MC 2 , COBRA-3M, FEVER, THERMOS, GAM-2, CINDER and EXTERMINATOR were selected for the study. For the final work THERMOS, GAM-2, CINDER and EXTERMINATOR have been selected and used. A one dimensional thermal hydraulics code also has been used to calculate temperature distributions in the core. THERMOS and CINDER have been modified to serve the purpose. Minor modifications have been made to GAM-2 and EXTERMINATOR to improve their utilization. All of the codes have been debugged on both CDC and IBM computers at the University of Illinois. IAEA 10 MW Benchmark problem has been solved. Results of this work has been compared with the IAEA contributor's results. Agreement is very good for highly enriched fuel (HEU). Deviations from IAEA contributor's mean value for low enriched fuel (LEU) exist but they are small enough in general

  6. SU-E-E-01: ABR Diagnostic Radiology Core Exam: Was Our Redesigned Physics Course Successful in Teaching Physics to Radiology Residents?

    International Nuclear Information System (INIS)

    Kanal, K; Hoff, M; Dickinson, R; Zamora, D; Stewart, B

    2014-01-01

    Purpose: Our purpose is to evaluate the effectiveness of our two year physics course in preparing radiology residents for the American Board of Radiology (ABR) diagnostic radiology exam. Methods: We designed a new two-year physics course that integrates radiology clinical content and practice and is primarily based on the AAPM curriculum and RSNA/AAPM physics modules. Biweekly classes focus on relevant concepts from assigned reading and use audience response systems to encourage participation. Teaching efficiency is optimized through lecturer rotations of physicists, radiologists, and guest speakers. An emphasis is placed on clinical relevance by requiring lab work and providing equipment demonstrations. Periodic quiz were given during the course. The course website was also redesigned for usability, and physics review lectures were conducted two weeks before the board exam to refresh key concepts. At the completion of our first two-year course, we conducted a confidential evaluation of the faculty and course. The evaluation assessed metrics such as overall organization, clinical relevance of content, and level of difficulty, with a rating scale from poor to excellent. Results: Our evaluation indicated that the redesigned course provided effective board exam preparation, with most responses between good and excellent. There was some criticism on the course length and on chronological discontinuity, but the review lectures were appreciated by the residents. All of our residents passed the physics component of the ABR exam with scores exceeding the minimum passing score by a significant margin. Conclusion: The course evaluation and board exam results indicate that our new two-year course format provides valuable board exam preparation. This is possible thanks to the time and effort taken by the physics faculty on ensuring the residents get quality physics education

  7. Study on high conversion type core of innovative water reactor for flexible fuel cycle (FLWR) for minor actinide (MA) recycling

    International Nuclear Information System (INIS)

    Fukaya, Yuji; Nakano, Yoshihiro; Okubo, Tsutomu

    2009-01-01

    In order to ensure sustainable energy supplies in the future based on the well-established light water reactor (LWR) technologies, conceptual design studies have been performed on the innovative water reactor for flexible fuel cycle (FLWR) with the high conversion ratio core. For early introduction of FLWR without a serious technical gap from the LWR technologies, the conceptual design of the high conversion type one (HC-FLWR) was constructed to recycle reprocessed plutonium. Furthermore, an investigation of minor actinide (MA) recycling based on the HC-FLWR core concept has been performed and is presented in this paper. Because HC-FLWR is a near-term technology, it would be a good option in the future if HC-FLWR can recycle MAs. In order to recycle MAs in HC-FLWR, it has been found that the core design should be changed, because the loaded MA makes the void reactivity coefficient worse and decreases the discharge burn-up. To find a promising core design specification, the investigation on the core characteristics were performed using the results from parameter surveys with core burn-up calculations. The final core designs were established by coupled three dimensional neutronics and thermal-hydraulics core calculations. The major core specifications are as follows. The plutonium fissile (Puf) content is 13 wt%. The discharge burn-up is about 55 GWd/t. Around 2 wt% of Np or Am can be recycled. The MA conversion ratios are around unity. In particular, it has been found that loaded Np can be transmuted effectively in this core concept. Therefore, these concepts would be a good option to reduce environmental burdens.

  8. Supplemental materials for the ICDP-USGS Eyreville A, B, and C core holes, Chesapeake Bay impact structure: Core-box photographs, coring-run tables, and depth-conversion files

    Science.gov (United States)

    Durand, C.T.; Edwards, L.E.; Malinconico, M.L.; Powars, D.S.

    2009-01-01

    During 2005-2006, the International Continental Scientific Drilling Program and the U.S. Geological Survey drilled three continuous core holes into the Chesapeake Bay impact structure to a total depth of 1766.3 m. A collection of supplemental materials that presents a record of the core recovery and measurement data for the Eyreville cores is available on CD-ROM at the end of this volume and in the GSA Data Repository. The supplemental materials on the CD-ROM include digital photographs of each core box from the three core holes, tables of the three coring-run logs, as recorded on site, and a set of depth-conversion programs. In this chapter, the contents, purposes, and basic applications of the supplemental materials are briefly described. With this information, users can quickly decide if the materials will apply to their specific research needs. ?? 2009 The Geological Society of America.

  9. Power distribution investigation in the transition phase of the low moderation type MOX fueled LWR from the high conversion core to the breeding core

    International Nuclear Information System (INIS)

    Akie, Hiroshi; Nakano, Yoshihiro; Okubo, Tsutomu

    2011-01-01

    The key concept of Innovative Water Reactor for Flexible Fuel Cycle (FLWR) is a core transition from a high conversion (HC) type to a plutonium breeding (BR) type in a same reactor system only by replacing fuel assemblies. Consequently in this transition phase, there are two types of assemblies in the same core. Due to the differences of the two assembly types, region-wise soft to hard neutron spectra appears and result in a large power peaking. Therefore, power distribution of FLWR in the HC to BR transition phase was studied by performing assembly and core calculations. For the whole core calculation, a new 14-group energy structure is developed to better represent the power distribution obtained with the fine 107-group structure than the 9-group structure in the previous evaluations. Calculations on few assemblies geometries show large local power peakings can be effectively reduced by considering plutonium enrichment distribution in an assembly. In the whole core calculation, there is a power level mismatch between HC and BR assemblies, but overall power distribution flattening is possible by optimizing fuel assemblies loading. Although the fuel loading should be decided also taking into account the void coefficient, transition from HC to BR type FLWR seems feasible without difficulty. (author)

  10. Procedure Redesign Methods : E3-Control: a redesign methodology for control procedures

    NARCIS (Netherlands)

    Liu, J.; Hofman, W.J.; Tan, Y.H.

    2011-01-01

    This chapter highlights the core research methodology, e3-control, that is applied throughout the ITAIDE project for the purpose of control procedure redesign. We present the key concept of the e3-control methodology and its technical guidelines. Based on the output of this chapter, domain experts

  11. Core Knowledge and Standards: A Conversation with E.D. Hirsch, Jr.

    Science.gov (United States)

    O'Neil, John

    1999-01-01

    Hirsch believes it is vitally important to specify the "core knowledge" that all students must learn. Here, Hirsch explains elements of his K-8 core-knowledge sequence. Teachers should avoid canned lessons but should know where they are going. New English standards are unacceptable, since they omit Shakespeare's works. (MLH)

  12. A study of HANARO core conversion using high density U-Mo fuel

    International Nuclear Information System (INIS)

    Lee, K.H.; Lee, C.S.; Lee, B.C.; Park, S.J.; Kim, H.; Kim, C.K.

    2002-01-01

    Currently, HANARO is using 3.15gU/cc U3Si/Al as a driver fuel. HANARO has seven vertical irradiation holes in the core region. Three of them including a central trap are located in the inner region of the core and mainly being used for material irradiation tests. Four of them are located in the reflector tank but cooled by primary coolant. They are used for fuel irradiation tests or radioisotope development tests. For minimum core modification using high density U-Mo fuels, no dimension change is assumed in the current fuel rods and the cladding thickness remains the same in this study. The high density U-Mo fuel will have up to about twice the linear uranium loading of a current HANARO driver fuel. Using this high density fuel 8 fuel sites can be replaced with irradiation sites. Three kinds of conceptual cores are considered using 5 gU/cc U-7Mo/Al and 16 gU/cc U-7Mo. The increase of the linear heat generation rate due to the decrease of total fuel length can be overcome by more uniform radial and axial power distribution using different uranium densities and different fuel meat diameters are introduced into those cores. The new core has 4.54 times larger surface-to-volume ratio than the reference core. The core uranium loading, linear heat generation rate, excess reactivity, and control rod worth as well as the neutron spectra are analysed for each core. (author)

  13. Core management and reactor physics aspects of the conversion of the NRU reactor to LEU

    International Nuclear Information System (INIS)

    Atfield, M.D.

    1985-01-01

    Results of work done to assess the effects of converting the NRU reactor to LEU are presented. The effects are small, and the operational rules and safety analysis, appropriate to the HEU core, will still apply. (author)

  14. Evidence of significant down-conversion in a Si-based solar cell using CuInS2/ZnS core shell quantum dots

    Science.gov (United States)

    Gardelis, Spiros; Nassiopoulou, Androula G.

    2014-05-01

    We report on the increase of up to 37.5% in conversion efficiency of a Si-based solar cell after deposition of light-emitting Cd-free, CuInS2/ZnS core shell quantum dots on the active area of the cell due to the combined effect of down-conversion and the anti- reflecting property of the dots. We clearly distinguished the effect of down-conversion from anti-reflection and estimated an enhancement of up to 10.5% in the conversion efficiency due to down-conversion.

  15. Evidence of significant down-conversion in a Si-based solar cell using CuInS2/ZnS core shell quantum dots

    International Nuclear Information System (INIS)

    Gardelis, Spiros; Nassiopoulou, Androula G.

    2014-01-01

    We report on the increase of up to 37.5% in conversion efficiency of a Si-based solar cell after deposition of light-emitting Cd-free, CuInS 2 /ZnS core shell quantum dots on the active area of the cell due to the combined effect of down-conversion and the anti- reflecting property of the dots. We clearly distinguished the effect of down-conversion from anti-reflection and estimated an enhancement of up to 10.5% in the conversion efficiency due to down-conversion

  16. Consequences of the conversion of research reactor cores on experimental facilities at the example of a cold neutron source

    International Nuclear Information System (INIS)

    Roegler, H.-J.; Goebs, H.; Stroemich, A.

    1985-01-01

    The consequences for and specifically the potential reduction of the performance of research reactors have been in discussions very often within the last five years as one of the draw-backs which has to be paid for the reduction of the proliferation risk at research reactor plants. Up to now and up to our knowledge the available results are restricted to unperturbated fluxes. Thus, this contribution makes the attempt to demonstrate the consequence of core conversion on an example of a real experimental facility and - at the same time - on one that is going to be used in the next decade a lot, i.e. a cold neutron source (CNS). (author)

  17. A study of core electron binding energies in technetium-99m complexes by internal conversion electron spectroscopy

    International Nuclear Information System (INIS)

    Burke, J.F.; Archer, C.M.; Wei Chiu, K.; Latham, I.A.; Egdell, R.G.

    1991-01-01

    Core electron binding energies in a series of 99m Tc complexes have been studied by internal conversion electron spectroscopy (ICES) in a conventional x-ray photoelectron spectrometer. In both 3d and 3p regions, a chemical shift of about 1 eV is observed per unit increase in oxidation state. The role of ICES in characterizing radiopharmaceutical agents is illustrated with studies of some novel 99m Tc-phosphine complexes that have been developed for myocardial perfusion imaging. (author)

  18. Thermal-hydraulic analysis for core conversion to the use of low-enriched uranium fuels in the KUR

    International Nuclear Information System (INIS)

    Mishima, Kaichiro; Kanda, Keiji; Shibata, Toshikazu

    1985-01-01

    A feasibility study has been performed on the core conversion to the use of low-enriched uranium (LEU) fuels in the KUR. Five fuel element geometries are studied. For each fuel element, the relation between the pressure drop and the flow rate, critical heat flux, and heat fluxes for the onset of flow instability and the onset of nucleate boiling are calculated using the computer code PLTEMP3.MOD1 which has been developed for this analysis. The effect of fuel material (UAl x -Al, U 3 O 8 -Al and U 3 Si 2 -Al) on the peak fuel temperatures is also studied. A particular interest in the mixed core which may be constructed on the way to the use of LEU fuels, the change in the bypass flow rate due to the change in the gap between different fuel elements is investigated. (author)

  19. Evaluation of core physics analysis methods for conversion of the INL advanced test reactor to low-enrichment fuel

    International Nuclear Information System (INIS)

    DeHart, M. D.; Chang, G. S.

    2012-01-01

    Computational neutronics studies to support the possible conversion of the ATR to LEU are underway. Simultaneously, INL is engaged in a physics methods upgrade project to put into place modern computational neutronics tools for future support of ATR fuel cycle and experiment analysis. A number of experimental measurements have been performed in the ATRC in support of the methods upgrade project, and are being used to validate the new core physics methods. The current computational neutronics work is focused on performance of scoping calculations for the ATR core loaded with a candidate LEU fuel design. This will serve as independent confirmation of analyses that have been performed previously, and will evaluate some of the new computational methods for analysis of a candidate LEU fuel for ATR. (authors)

  20. Core conversion from rod to plate type fuel elements in research reactors

    International Nuclear Information System (INIS)

    Khattab, M.S.; Mina, A.R.

    1997-01-01

    Core thermalhydraulic analysis have been performed for rod and plate types fuel elements without altering the core bundles square grid spacer (68 mm, side) and coolant mass flow rate. The U O 2 -Mg, 10% enrichment rod type fuel elements are replaced by the MTR plate type, U-Al alloy of 20% enrichment. Coolant mass flux increased from 2000 kg/m 2 S to 5000 kg/m 2 S. Reactor power could be upgraded from 2 to 10 MW without significantly altering the steady state, thermal-hydraulic safety margins. Fuel, clad and coolant transient temperatures are determined inside the core hot channel during flow coast down using paret code. Residual heat removal system of 20% coolant capacity is necessary for upgrading reactor power to encounter the case of pumps off at 10 MW nominal operation. 6 figs., 2 tabs

  1. Neutronic analysis of the conversion of HEU to LEU fuel for a 5-MW MTR core

    International Nuclear Information System (INIS)

    Pazirandeh, A.; Bartsch, G.

    1987-01-01

    In recent years, due to cessation of highly enriched uranium (HEU) fuel supply, practical steps have been taken to substitute HEU fuel in almost all research reactors by medium-enriched uranium or low-enriched uranium (LEU) fuels. In this study, a neutronic calculation of a 5-MW research reactor core fueled with HEU (93% 235 U) is presented. In order to assess the performance of the core with the LEU ( 235 U loadings were examined. The core consists of 22 standard fuel elements (SFEs) and 6 control fuel elements (CFEs). Each fuel elements has 18 curved plates of which two end plates are dummies. Initial 235 U content is 195 g 235 U/SFE and 9.7 g 235 U/CFE or /PFE. In all calculations the permitted changes to the fuel elements are (a) 18 active plates per SFE, (b) fuel plates assumed to be flat, and (c) 8 or 9 active plates per CFE

  2. Conversion of the core of the TRIGA Mark III reactor at the Mexican Nuclear Centre

    International Nuclear Information System (INIS)

    Moran Lopez, J.M.; Lucatero, M.A.; Reyes Andrade, B.; Rivero Gutierrez, T.; Sainz Mejia, E.

    1990-01-01

    It was decided to convert the core of the TRIGA MARK III reactor at the Mexican Nuclear Centre run by the National Nuclear Institute because of problems detected during the operation, such as a lack of excess reactivity for operation at nominal power over long periods and difficulties in the maintenance and calibration of the control panel. In order to compensate for the lack of excess reactivity the fuel elements taken to the highest burnup were replaced by fresh elements acquired for this purpose. The latter, however, had a different enrichment, and this necessitated a detailed analysis of the neutronic and thermohydraulic behaviour of the reactor with a view to determining a mixed core configuration which would meet safe operation requirements. In conducting the thermohydraulic analysis, a natural convection coolant flow model was developed to determine coolant velocity and pressure drop patterns within the core. The heat transfer equations were solved and it was found that the hottest fuel element did not attain critical heat flux conditions. In loading this core it was also necessary to analyse procedures and to consider the possible effects of reaching criticality with fuel elements having different enrichments. The loading procedure is described, as is the measurement system and the results obtained. In order to resolve the calibration and maintenance problems, a new, more advanced control panel was designed with conventional and nuclear detection systems and modern components

  3. Characterization of the fast neutron irradiation facility of the Portuguese Research Reactor after core conversion

    International Nuclear Information System (INIS)

    Marques, J.G.; Sousa, M.; Santos, J.P.; Fernandes, A.C.

    2011-01-01

    The fast neutron irradiation facility of the Portuguese Research Reactor was characterized after the reduction in uranium enrichment and rearrangement of the core configuration. In this work we report on the determination of the hardness parameter and the 1 MeV equivalent neutron flux along the facility, in the new irradiation conditions, following ASTM E722 standard.

  4. Design and Fabrication of Air-core Inductors for Power Conversion

    DEFF Research Database (Denmark)

    Lê Thanh, Hoà; Mizushima, Io; Tang, Peter Torben

    supply on chip (PwrSoC) [1]. Examples of PwrSoC applications are power adaptors for LED illumination and the “Internet of Things”. We report an air-core MEMS inductor. Our process is scalable and universal for making inductors with versatile geometries e.g. spiral, solenoid, toroid, and advanced...

  5. Common Core Preparation in Special Education Teacher Education Programs: Beginning the Conversation

    Science.gov (United States)

    Murphy, Michelle R.; Marshall, Kathleen J.

    2015-01-01

    The Common Core State Standards (CCSS) were developed to encourage a common focus of instruction and evaluation in the areas of mathematics, reading/language arts, writing, speaking, and listening. As of 2011, all but five states have adopted CCSS for math and English Language Arts (ELA), with another adopting only the standards for ELA. With…

  6. Progress in safety evaluation for the JMTR core conversion to LEU fuel

    International Nuclear Information System (INIS)

    Sakurai, F.; Komori, Y.; Saito, J.; Komukai, B.; Ando, H.; Nakata, H.; Sakakura, A.; Niiho, S.; Saito, M.; Futamura, Y.

    1991-01-01

    The JMTR (50 MWt) has been in steady operation with MEU fuel since July 1986. The effort is still continued to convert the core from MEU to LEU fuel. The LEU silicide fuel element at 4.8 gU/cm 3 with Cd wires as burnable absorbers has been selected in order to achieve upgraded fuel cycle performance of extended cycle length and reduced control rod movement operation. The neutronic calculation methods (diffusion theory model) developed for the LEU core with Cd wires was benchmarked with a detailed Monte Carlo model and verified experimentally using the critical facility, JMTRC. Hydraulic tests of the LEU silicide fuel element with Cd wires were completed with satisfactory results, and measurements of release/born (R/B) ratios of FPs of silicide fuel at high temperature are in progress. (orig.)

  7. Organizations as machines, organizations as conversations: two core metaphors and their consequences.

    Science.gov (United States)

    Suchman, Anthony L

    2011-12-01

    One factor contributing to the limited success of organizational change initiatives is the use of an outmoded conceptual model: the organization as machine. This metaphor leads to the creation of detailed blueprints for desired changes; invites unrealistic expectations of control; and creates anxiety, blame and defensiveness when events inevitably do not proceed according to plan, thus hindering the work. An alternative conceptualization--the organization as conversation--portrays an organization not as a reified object upon which we can act but as self-organizing patterns of thinking (organizational identity and knowledge) and relating (organizational culture) that exist in the medium of human interaction in which we participate. Principles of complexity dynamics (self-organization) have important implications for organizational change practices. (1) Organizational change requires mindful participation--reflecting on and talking about what we are doing together here and now, what patterns of thinking and interacting we are enacting, and what new behaviors might interrupt old patterns or give rise to new ones. (2) Diversity and responsiveness favor the emergence of novel patterns. Skilled facilitation can enhance these characteristics when novelty is desirable; checklists and protocols can diminish these characteristics when consistency and reliability are needed. (3) We cannot know in advance the outcomes of our actions so we need to hold plans lightly, value "not knowing" and practice emergent design. The organization-as-conversation perspective also has important implications for T3 translational research, redefining its purpose, suggesting new methodologies, and requiring new approaches for evaluating proposed and completed projects.

  8. Neutronics substantiation of possibility for conversion of the WWR-K reactor core to operation with low-enriched fuel

    International Nuclear Information System (INIS)

    Arinkin, F.M.; Gizatulin, Sh.H.; Zhantikin, T.M.; Koltochnik, S.N.; Takibaev, A.Zh.; Talanov, S.V.; Chakrov, P.V.; Chekushina, L.V.

    2002-01-01

    The studies are aimed to calculation and experimental justification of possibility for conversion of the WWR-R reactor core to low-enriched nuclear fuel (the 19.75-% enrichment in isotope U-235), resulting in reducing the risk of non-sanctioned proliferation of nuclear materials which can be used as weapons materials. The analysis of available published data, related to problem of reduction of enrichment in the fuel used in research thermal reactors, has been carried out. Basing on the analysis results, reference fuel compositions have been chosen, in particular, uranium dioxide (UO 2 ) in aluminum master form and the UA1 4 alloy. Preliminary calculations have shown that, with the WWR-K reactor core preserved existing critical characteristics (the fuel composition: UA1 4 ), the uranium concentration in the fuel element is to be increased by a factor of 2.0-2.2, being impossible technologically. The calculations have been performed by means of the Monte Carlo computational codes. The program of optimal conversion of the WWR-K reactor core to low-enriched fuel has been developed, including: development of calculation models of the reactor core, composed of various designs of fuel elements and fuel assemblies (FA), on a base of corresponding computational codes (diffusion, statistical, etc.); implementation of experiments in the zero-power reactor (critical assembly) with the WWR-C-type FA, in view of correction of the computational constants used in calculations; implementation of reactor core neutronics calculations, in view of selection of the U-235 optimal content in the low-enriched fuel elements and choice of FA reload strategy at the regime of reactor core after burning; determination of the fuel element specification; determination of the critical and operational loads for the reactor core composed of rod/tubular fuel elements; calculation of the efficiency of the protection control system effectors, optimization of its composition, number and locations in the

  9. Broadband absorption and enhanced photothermal conversion property of octopod-like Ag@Ag2S core@shell structures with gradually varying shell thickness.

    Science.gov (United States)

    Jiang, Qian; Zeng, Wenxia; Zhang, Canying; Meng, Zhaoguo; Wu, Jiawei; Zhu, Qunzhi; Wu, Daxiong; Zhu, Haitao

    2017-12-19

    Photothermal conversion materials have promising applications in many fields and therefore they have attracted tremendous attention. However, the multi-functionalization of a single nanostructure to meet the requirements of multiple photothermal applications is still a challenge. The difficulty is that most nanostructures have specific absoprtion band and are not flexible to different demands. In the current work, we reported the synthesis and multi-band photothermal conversion of Ag@Ag 2 S core@shell structures with gradually varying shell thickness. We synthesized the core@shell structures through the sulfidation of Ag nanocubes by taking the advantage of their spatially different reactivity. The resulting core@shell structures show an octopod-like mopgorlogy with a Ag 2 S bulge sitting at each corner of the Ag nanocubes. The thickness of the Ag 2 S shell gradually increases from the central surface towards the corners of the structure. The synthesized core@shell structures show a broad band absorption spectrum from 300 to 1100 nm. Enhanced photothermal conversion effect is observed under the illuminations of 635, 808, and 1064 nm lasers. The results indicate that the octopod-like Ag@Ag 2 S core@shell structures have characteristics of multi-band photothermal conversion. The current work might provide a guidance for the design and synthesis of multifunctional photothermal conversion materials.

  10. Motivation Enhancement Through Work Redesign.

    Science.gov (United States)

    Oldham, Greg R., Kulik, Carol T.

    1983-01-01

    The possibility of redesigning the work experiences of faculty members in an effort to enhance their motivation, productivity, and personal and work satisfactions is examined. One approach to work redesign, job characteristics theory, is described. Several strategies are discussed. (Author/MLW)

  11. Research reactor core conversion guidebook. V. 3: Analytical verification (Appendices G and H)

    International Nuclear Information System (INIS)

    1992-04-01

    Volume 3 consists of Appendix G which contains detailed results of a safety-related benchmark problem for an idealized reactor and Appendix H which contains detailed comparisons of calculated and measured data for actual cores with moderately enriched uranium and low enriched uranium fuels. The results of the benchmark calculations in Appendix G are summarized in Chapter 7 of Volume 1 and the results of the comparisons between calculations and measurements are summarized in Chapter 8 of Volume 1. Both the approaches described in these appendices are very useful in ensuring that the calculational methods employed in the preparation of a Safety Report are accurate. As a first step, it is recommended that reactor operators/physicists use their own methods and codes to first calculate the benchmark problem, and then compare the results of calculations with measurements in their own reactor or in one of the reactors for which measured data is available in Appendix H. (author). Refs, figs and tabs

  12. Neutronic calculations in core conversion of the IAN-R1 research reactor from MTR HEU to TRIGA LEU fuel

    International Nuclear Information System (INIS)

    Sarta Fuentes, Jose A.; Castiblanco, L.A.

    2003-01-01

    With cooperation of the International Atomic Energy Agency (IAEA), neutronic calculations were carried out for conversion of the Ian-R1 Reactor from MTR-HEU fuel to TRIGA-LEU fuel. In order to establish a staff for neutronic calculation at the Instituto de Cancan's Nucleares y Energia s Alternatives (INEA) a program was established. This program included training, acquisition of hardware, software and calculation for the core with MTR-HEU fuel , enriched nominally to 93% and calculation for several arrangements with the TRIGA-LEU fuel, enriched to 19.7%. The results were verified and compared with several groups of calculation at the Instituto Nacional de Investigaciones Nucleares (ININ) in Mexico, and General Atomics (GA) in United States. As a result of this program, several technical reports have been wrote. (author)

  13. Amyloid cores in prion domains: Key regulators for prion conformational conversion.

    Science.gov (United States)

    Fernández, María Rosario; Batlle, Cristina; Gil-García, Marcos; Ventura, Salvador

    2017-01-02

    Despite the significant efforts devoted to decipher the particular protein features that encode for a prion or prion-like behavior, they are still poorly understood. The well-characterized yeast prions constitute an ideal model system to address this question, because, in these proteins, the prion activity can be univocally assigned to a specific region of their sequence, known as the prion forming domain (PFD). These PFDs are intrinsically disordered, relatively long and, in many cases, of low complexity, being enriched in glutamine/asparagine residues. Computational analyses have identified a significant number of proteins having similar domains in the human proteome. The compositional bias of these regions plays an important role in the transition of the prions to the amyloid state. However, it is difficult to explain how composition alone can account for the formation of specific contacts that position correctly PFDs and provide the enthalpic force to compensate for the large entropic cost of immobilizing these domains in the initial assemblies. We have hypothesized that short, sequence-specific, amyloid cores embedded in PFDs can perform these functions and, accordingly, act as preferential nucleation centers in both spontaneous and seeded aggregation. We have shown that the implementation of this concept in a prediction algorithm allows to score the prion propensities of putative PFDs with high accuracy. Recently, we have provided experimental evidence for the existence of such amyloid cores in the PFDs of Sup35, Ure2, Swi1, and Mot3 yeast prions. The fibrils formed by these short stretches may recognize and promote the aggregation of the complete proteins inside cells, being thus a promising tool for targeted protein inactivation.

  14. Core conversion study from silicide to molybdenum fuel in the Indonesian 30 MW multipurpose reactor G.A. Siwabessy (RSG-GAS)

    International Nuclear Information System (INIS)

    Sembiring, T.M.; Kuntoro, I.

    2005-01-01

    This paper describes the core conversion from silicide to molybdenum core through a series of silicide (2.96 gU cm -3 ) - molybdenum (3.55 gUcm -3 ) mixed transition cores for the Indonesian 30 MW-Multipurpose G.A. Siwabessy (RSGGAS) reactor. The core calculations are carried out using the two-dimensional multigroup neutron diffusion method code of Batan-EQUIL-2D. The calculated results showed that the proposed silicide-molybdenum mixed transition cores, using the same refueling/reshuffling scheme, meet the safety criteria and it can be used in safely converting from an all-silicide core to an all-molybdenum core. (author)

  15. Criticality safety assessment on the RSG-GAS spent fuel storage for anticipating the next core conversion program

    International Nuclear Information System (INIS)

    Sembiring, Tagor Malem; Kuntoro, Iman; Zuhair; Liem, Peng Hong

    2003-01-01

    Criticality assessment on the spent fuel storage racks of the RSG-GAS multipurpose reactor has been conducted to support the undergoing core conversion program, in which higher uranium fuel densities of silicide (up to 4.8 gU.cm -3 ) and molybdenum (up to 8.3 gU.cm -3 ) fuel elements are adopted to enhance the reactor performance, core cycle length and reactor utilization. In the assessment, the k eff of the rack as a function of fuel density is calculated for fresh fuel elements which is a very conservative approach recommended by IAEA. Besides fuel densities, effects of water densities due to pool water temperature variation, and the fuel elements' orientation on the k eff are analyzed as well. The criticality calculations are all carried out by using MNCP4B2 Monte Carlo code with ENDF/B-VI library. For the library sensitivity, JENDL-3.3 library is also used and compared. The calculation results show the most reactive condition is for the case when the spent fuel racks are filled with fresh U-6Mo fuel element with meat density of 8.30 gU.cm -3 . For all fuel types, density and operating condition, the calculated k eff with 3 times standard deviations are confirmed less than the allowable value of 0.95. It can be concluded that the existing spent fuel storage racks can be safely used for storing the planned high density uranium fuels. (author)

  16. Proceedings of the international meeting on research and test reactor core conversions from HEU to LEU fuels

    International Nuclear Information System (INIS)

    Travelli, A.

    1983-09-01

    Conversion of research and test reactor cores from the use of high enrichment uranium to the use of low enrichment uranium depends on the cooperation of many research organizations, reactor operators, and government agencies. At a technical level, it involves almost all aspects of the fuel cycle, including fuel development, testing, shipping and reprocessing; experiment performance; economics; and safety and licensing aspects. The reactors involved and the conversion activities are distributed among approximately 25 countries, making this a subject which is best dealt with on an international basis. To foster direct communication in this area, the Reduced Enrichment Research and Test Reactor (RERTR) Program, at the Argonne National Laboratory, sponsored this meeting as the fifth of a series which began in 1978. The previous meetings were held at Argonne (International Meeting of Research Reactor Fuel Designers, Developers, and Fabricators, Argonne National Laboratory, Argonne, U.S.A., November 910, 1978), at Saclay (IAEA Consultants' Meeting on Research Reactor Core Conversions from HEU to LEU, Centre d'etudes Nucleaires de Saclay, Saclay, France, December 12-14, 1979), at Argonne (International Meeting on Development, Fabrication and Application of Reduced Enrichment Fuels for Research and Test Reactors, Argonne National Laboratory, Argonne, U.S.A., November 12-14, 1980) and at Juelich (Seminar on Research Reactor Operation and Use, Juelich Nuclear Research Center, Juelich, F.R.G., September 48, 1981). Proceedings from the two most recent previous meetings were published as ANL/RERTR/TM-3 (CONF-801144) and IAEA-SR-77. The spirit of this meeting differs slightly from that of the previous meetings. The advances which have been made and the growing maturity of the effort have caused a gradual shift of emphasis away from those topics which dominated the floor during the first meetings, such as fuel and methods development, and towards topics which concern more

  17. Proceedings of the international meeting on research and test reactor core conversions from HEU to LEU fuels

    Energy Technology Data Exchange (ETDEWEB)

    Travelli, A [Argonne National Laboratory, Argonne, IL (United States)

    1983-09-01

    Conversion of research and test reactor cores from the use of high enrichment uranium to the use of low enrichment uranium depends on the cooperation of many research organizations, reactor operators, and government agencies. At a technical level, it involves almost all aspects of the fuel cycle, including fuel development, testing, shipping and reprocessing; experiment performance; economics; and safety and licensing aspects. The reactors involved and the conversion activities are distributed among approximately 25 countries, making this a subject which is best dealt with on an international basis. To foster direct communication in this area, the Reduced Enrichment Research and Test Reactor (RERTR) Program, at the Argonne National Laboratory, sponsored this meeting as the fifth of a series which began in 1978. The previous meetings were held at Argonne (International Meeting of Research Reactor Fuel Designers, Developers, and Fabricators, Argonne National Laboratory, Argonne, U.S.A., November 910, 1978), at Saclay (IAEA Consultants' Meeting on Research Reactor Core Conversions from HEU to LEU, Centre d'etudes Nucleaires de Saclay, Saclay, France, December 12-14, 1979), at Argonne (International Meeting on Development, Fabrication and Application of Reduced Enrichment Fuels for Research and Test Reactors, Argonne National Laboratory, Argonne, U.S.A., November 12-14, 1980) and at Juelich (Seminar on Research Reactor Operation and Use, Juelich Nuclear Research Center, Juelich, F.R.G., September 48, 1981). Proceedings from the two most recent previous meetings were published as ANL/RERTR/TM-3 (CONF-801144) and IAEA-SR-77. The spirit of this meeting differs slightly from that of the previous meetings. The advances which have been made and the growing maturity of the effort have caused a gradual shift of emphasis away from those topics which dominated the floor during the first meetings, such as fuel and methods development, and towards topics which concern more

  18. ILRS Website Redesign

    Science.gov (United States)

    Noll, C.; Lee, L.; Torrence, M.

    2011-01-01

    The International Laser Ranging Service (ILRS) website, http://ilrs.gsfc.nasa.gov, is the central source of information for all aspects of the service. The website provides information on the organization and operation of ILRS and descriptions of ILRS components, data, and products. Furthermore, the website and provides an entry point to the archive of these data and products available through the data centers. Links are provided to extensive information on the ILRS network stations including performance assessments and data quality evaluations. Descriptions of supported satellite missions (current, future, and past) are provided to aid in station acquisition and data analysis. The current format for the ILRS website has been in use since the early years of the service. Starting in 2010, the ILRS Central Bureau began efforts to redesign the look and feel for the website. The update will allow for a review of the contents, ensuring information is current and useful. This poster will detail the proposed design including specific examples of key sections and webpages.

  19. Website Redesign: A Case Study.

    Science.gov (United States)

    Wu, Jin; Brown, Janis F

    2016-01-01

    A library website redesign is a complicated and at times arduous task, requiring many different steps including determining user needs, analyzing past user behavior, examining other websites, defining design preferences, testing, marketing, and launching the site. Many different types of expertise are required over the entire process. Lessons learned from the Norris Medical Library's experience with the redesign effort may be useful to others undertaking a similar project.

  20. Effect of the shell material and confinement type on the conversion efficiency of core/shell quantum dot nanocrystal solar cells.

    Science.gov (United States)

    Sahin, Mehmet

    2018-05-23

    In this study, the effects of the shell material and confinement type on the conversion efficiency of core/shell quantum dot nanocrystal (QDNC) solar cells have been investigated in detail. For this purpose, the conventional, i.e. original, detailed balance model, developed by Shockley and Queisser to calculate an upper limit for the conversion efficiency of silicon p-n junction solar cells, is modified in a simple and effective way to calculate the conversion efficiency of core/shell QDNC solar cells. Since the existing model relies on the gap energy ([Formula: see text]) of the solar cell, it does not make an estimation about the effect of QDNC materials on the efficiency of the solar cells, and gives the same efficiency values for several QDNC solar cells with the same [Formula: see text]. The proposed modification, however, estimates a conversion efficiency in relation to the material properties and also the confinement type of the QDNCs. The results of the modified model show that, in contrast to the original one, the conversion efficiencies of different QDNC solar cells, even if they have the same [Formula: see text], become different depending upon the confinement type and shell material of the core/shell QDNCs, and this is crucial in the design and fabrication of the new generation solar cells to predict the confinement type and also appropriate QDNC materials for better efficiency.

  1. Effect of the shell material and confinement type on the conversion efficiency of core/shell quantum dot nanocrystal solar cells

    Science.gov (United States)

    Sahin, Mehmet

    2018-05-01

    In this study, the effects of the shell material and confinement type on the conversion efficiency of core/shell quantum dot nanocrystal (QDNC) solar cells have been investigated in detail. For this purpose, the conventional, i.e. original, detailed balance model, developed by Shockley and Queisser to calculate an upper limit for the conversion efficiency of silicon p–n junction solar cells, is modified in a simple and effective way to calculate the conversion efficiency of core/shell QDNC solar cells. Since the existing model relies on the gap energy () of the solar cell, it does not make an estimation about the effect of QDNC materials on the efficiency of the solar cells, and gives the same efficiency values for several QDNC solar cells with the same . The proposed modification, however, estimates a conversion efficiency in relation to the material properties and also the confinement type of the QDNCs. The results of the modified model show that, in contrast to the original one, the conversion efficiencies of different QDNC solar cells, even if they have the same , become different depending upon the confinement type and shell material of the core/shell QDNCs, and this is crucial in the design and fabrication of the new generation solar cells to predict the confinement type and also appropriate QDNC materials for better efficiency.

  2. Redesigning the Way We Listen

    DEFF Research Database (Denmark)

    Søndergaard, Morten

    2014-01-01

    This paper is based on a research project-in-progress investigating curatorial practice as methodology for creating responsive interfaces to sound art practices. Sound art is a transdisciplinary practice. As such, it creates new domains that may be used for redesign-purposes. Not only do experien......This paper is based on a research project-in-progress investigating curatorial practice as methodology for creating responsive interfaces to sound art practices. Sound art is a transdisciplinary practice. As such, it creates new domains that may be used for redesign-purposes. Not only do...... experiences of sound alter; the way we listen to sound is transforming as well. Thus, the paper analyses and discusses two responsive sound interfaces and claim that curating as a transdisciplinary practice may frame what is termed in the paper as a domain-game redesigning the way the audience listens...

  3. Redesign of the SNS Modulator H-Bridge for Utilization of Press-Pack IGBTs

    Energy Technology Data Exchange (ETDEWEB)

    Kemp, Mark A.; Burkhart, Craig; /SLAC; Anderson, David E.; /Oak Ridge

    2008-09-25

    The power conversion group at SLAC is currently redesigning the H-bridge switch plates of the High Voltage Converter Modulators at the Spallation Neutron Source. This integral part to the modulator operation has been indentified as a source of several modulator faults and potentially limits reliability with pulse width modulation operation. This paper is a presentation of the design and implementation of a redesigned switch plate based upon press-pack IGBTs.

  4. H{sub 2} Ortho-to-para Conversion on Grains: A Route to Fast Deuterium Fractionation in Dense Cloud Cores?

    Energy Technology Data Exchange (ETDEWEB)

    Bovino, S. [Hamburger Sternwarte, Universität Hamburg, Gojenbergsweg 112, D-21029 Hamburg (Germany); Grassi, T. [Centre for Star and Planet Formation, Niels Bohr Institute and Natural History Museum of Denmark, University of Copenhagen, Øster Voldgade 5-7, DK-1350 Copenhagen (Denmark); Schleicher, D. R. G. [Departamento de Astronomía, Facultad Ciencias Físicas y Matemáticas, Universidad de Concepción, Av. Esteban Iturra s/n Barrio Universitario, Casilla 160, Concepción (Chile); Caselli, P., E-mail: stefano.bovino@uni-hamburg.de [Max-Planck-Institut für extraterrestrische Physik, Giessenbachstrasse 1, D-85748 Garching (Germany)

    2017-11-10

    Deuterium fractionation, i.e., the enhancement of deuterated species with respect to non-deuterated ones, is considered to be a reliable chemical clock of star-forming regions. This process is strongly affected by the ortho-to-para H{sub 2} ratio. In this Letter we explore the effect of the ortho–para (o–p) H{sub 2} conversion on grains on the deuteration timescale in fully-depleted dense cores, including the most relevant uncertainties that affect this complex process. We show that (i) the o–p H{sub 2} conversion on grains is not strongly influenced by the uncertainties on the conversion time and the sticking coefficient, and (ii) that the process is controlled by the temperature and the residence time of ortho-H{sub 2} on the surface, i.e., by the binding energy. We find that for binding energies between 330 and 550 K, depending on the temperature, the o–p H{sub 2} conversion on grains can shorten the deuterium fractionation timescale by orders of magnitude, opening a new route for explaining the large observed deuteration fraction D {sub frac} in dense molecular cloud cores. Our results suggest that the star formation timescale, when estimated through the timescale to reach the observed deuteration fractions, might be shorter than previously proposed. However, more accurate measurements of the binding energy are needed in order to better assess the overall role of this process.

  5. 10 CFR 501.67 - Petition redesignations.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Petition redesignations. 501.67 Section 501.67 Energy... Certifications § 501.67 Petition redesignations. OFE, with the petitioner's approval, will redesignate an exemption petition if the petitioner qualifies for an exemption other than the one originally requested...

  6. Anisotropic nanolaminated CoNiFe cores integrated into microinductors for high-frequency dc–dc power conversion

    International Nuclear Information System (INIS)

    Kim, Jooncheol; Kim, Minsoo; Herrault, Florian; Kim, Jung-Kwun; Allen, Mark G

    2015-01-01

    This paper presents a rectangular, anisotropic nanolaminated CoNiFe core that possesses a magnetically hard axis in the long geometric axis direction. Previously, we have developed nanolaminated cores comprising tens to hundreds of layers of 300–1000 nm thick metallic alloys (i.e. Ni 80 Fe 20 or Co 44 Ni 37 Fe 19 ) based on sequential electrodeposition, demonstrating suppressed eddy-current losses at MHz frequencies. In this work, magnetic anisotropy was induced to the nanolaminated CoNiFe cores by applying an external magnetic field (50–100 mT) during CoNiFe film electrodeposition. The fabricated cores comprised tens to hundreds of layers of 500–1000 nm thick CoNiFe laminations that have the hard-axis magnetic property. Packaged in a 22-turn solenoid test inductor, the anisotropic core showed 10% increased effective permeability and 25% reduced core power losses at MHz operation frequency, compared to an isotropic core of the identical geometry. Operating the anisotropic nanolaminated CoNiFe core in a step-down dc–dc converter (15 V input to 5 V output) demonstrated 81% converter efficiency at a switching frequency of 1.1 MHz and output power of 6.5 W. A solenoid microinductor with microfabricated windings integrated with the anisotropic nanolaminated CoNiFe core was fabricated, demonstrating a constant inductance of 600 nH up to 10 MHz and peak quality factor exceeding 20 at 4 MHz. The performance of the microinductor with the anisotropic nanolaminated CoNiFe core is compared with other previously reported microinductors. (fast track communication)

  7. Outstanding efficiency in energy conversion for electric motors constructed by nanocrystalline soft magnetic alloy “NANOMET®” cores

    Directory of Open Access Journals (Sweden)

    N. Nishiyama

    2016-05-01

    Full Text Available Recently updated nanocrystalline soft magnetic Fe-Co-Si-B-P-Cu alloys “NANOMET®” exhibit high saturation magnetic flux density (Bs > 1.8 T, low coercivity (Hc < 10 A/m and low core loss (W1.7/50 ∼ 0.4 W/kg even in a ribbon form with a thickness of up to 40 μm. By utilize excellent magnetic softness, several products such as motors or transformers for electrical appliances are now under developing by industry-academia collaboration. In particular, it is found that a brushless DC motor using NANOMET® core exhibited remarkable improvement in energy consumption. The prototype motor with an outer core diameter of 70 mm and a core thickness of 50 mm was constructed using laminated nano-crystallized NANOMET® ribbons. Core-loss for the constructed motor was improved from 1.4 W to 0.4 W only by replacing the non-oriented Si-steel core with NANOMET® one. The overall motor efficiency is evaluated to be 3% improvement. In this work, the relation between processing and resulting magnetic properties will be presented. In addition, feasibility for commercialization will also be discussed.

  8. Highly efficient photocatalytic conversion of solar energy to hydrogen by WO3/BiVO4 core-shell heterojunction nanorods

    Science.gov (United States)

    Kosar, Sonya; Pihosh, Yuriy; Bekarevich, Raman; Mitsuishi, Kazutaka; Mawatari, Kazuma; Kazoe, Yutaka; Kitamori, Takehiko; Tosa, Masahiro; Tarasov, Alexey B.; Goodilin, Eugene A.; Struk, Yaroslav M.; Kondo, Michio; Turkevych, Ivan

    2018-04-01

    Photocatalytic splitting of water under solar light has proved itself to be a promising approach toward the utilization of solar energy and the generation of environmentally friendly fuel in a form of hydrogen. In this work, we demonstrate highly efficient solar-to-hydrogen conversion efficiency of 7.7% by photovoltaic-photoelectrochemical (PV-PEC) device based on hybrid MAPbI3 perovskite PV cell and WO3/BiVO4 core-shell nanorods PEC cell tandem that utilizes spectral splitting approach. Although BiVO4 is characterized by intrinsically high recombination rate of photogenerated carriers, this is not an issue for WO3/BiVO4 core-shell nanorods, where highly conductive WO3 cores are combined with extremely thin absorber BiVO4 shell layer. Since the BiVO4 layer is thinner than the characteristic carrier diffusion length, the photogenerated charge carriers are separated at the WO3/BiVO4 heterojunction before their recombination. Also, such architecture provides sufficient optical thickness even for extremely thin BiVO4 layer due to efficient light trapping in the core-shell WO3/BiVO4 nanorods with high aspect ratio. We also demonstrate that the concept of fill factor can be used to compare I-V characteristics of different photoanodes regarding their optimization for PV/PEC tandem devices.

  9. Metal-Organic Framework Derived Iron Sulfide-Carbon Core-Shell Nanorods as a Conversion-Type Battery Material

    DEFF Research Database (Denmark)

    Huang, Wei; Li, Shuo; Cao, Xianyi

    2017-01-01

    of a redox conversion-type lithium-ion battery, this composite material has demonstrated high lithium-ion storage capacity at 1148 mA h g-1 under the current rate of 500 mA g-1 for 170 cycles and an impressive rate-retention capability at 657 mA h g-1 with a current density of 2000 mA g-1. On the basis......We report the design and nanoengineering of carbon-film-coated iron sulfide nanorods (C@Fe7S8) as an advanced conversion-type lithium-ion storage material. The structural advantages of the iron-based metal-organic framework (MIL-88-Fe) as both a sacrificed template and a precursor are explored...

  10. Research reactor core conversion from the use of highly enriched uranium to the use of low enriched uranium fuels guidebook

    International Nuclear Information System (INIS)

    1980-08-01

    In view of the proliferation concerns caused by the use of highly enriched uranium (HEU) and in anticipation that the supply of HEU to research and test reactors will be more restricted in the future, this document has been prepared to assist reactor operators in determining whether conversion to the use of low enriched uranium (LEU) fuel designs is technically feasible for their specific reactor, and to assist in making a smooth transition to the use of LEU fuel designs where appropriate

  11. Proceedings of the international meeting on research and test reactor core conversions from HEU to LEU fuels

    International Nuclear Information System (INIS)

    1983-09-01

    Separate abstracts have been prepared for each paper presented in the following areas of interest: (1) fuel development; (2) post-irradiation examinations; (3) reprocessing; (4) thermite reaction; (5) fuel fabrication; (6) element tests; (7) core tests; (8) criticals; (9) shipping; and (10) reactors and methods

  12. Influencing Organizational Commitment through Office Redesign

    Science.gov (United States)

    Morrow, Paula C.; McElroy, James C.; Scheibe, Kevin P.

    2012-01-01

    Prior research on the effects of office redesign on work-related outcomes has been largely a theoretical and yielded mixed and conflicting findings. Expanding on individual reactions to office design changes as specified by social interference theory, we propose that office redesign affects organizational commitment and this relationship is…

  13. 78 FR 27968 - Federal Management Regulation; Redesignations of Federal Buildings

    Science.gov (United States)

    2013-05-13

    ... Management Regulation; Redesignations of Federal Buildings AGENCY: Public Buildings Service (PBS), General... designation and redesignation of six Federal buildings. DATES: Expiration Date: This bulletin announcement expires July 30, 2013. The building designations and redesignations remains in effect until canceled or...

  14. Conceptual design analysis of an MHD power conversion system for droplet-vapor core reactors. Final report

    International Nuclear Information System (INIS)

    Anghaie, S.; Saraph, G.

    1995-01-01

    A nuclear driven magnetohydrodynamic (MHD) generator system is proposed for the space nuclear applications of few hundreds of megawatts. The MHD generator is coupled to a vapor-droplet core reactor that delivers partially ionized fissioning plasma at temperatures in range of 3,000 to 4,000 K. A detailed MHD model is developed to analyze the basic electrodynamics phenomena and to perform the design analysis of the nuclear driven MHD generator. An incompressible quasi one dimensional model is also developed to perform parametric analyses

  15. A design study of reactor core optimization for direct nuclear heat-to-electricity conversion in a space power reactor

    Energy Technology Data Exchange (ETDEWEB)

    Yoshikawa, Hidekazu; Takahashi, Makoto; Shimoda, Hiroshi; Takeoka, Satoshi [Kyoto Univ. (Japan); Nakagawa, Masayuki; Kugo, Teruhiko

    1998-01-01

    To propose a new design concept of a nuclear reactor used in the space, research has been conducted on the conceptual design of a new nuclear reactor on the basis of the following three main concepts: (1) Thermionic generation by thermionic fuel elements (TFE), (2) reactivity control by rotary reflector, and (3) reactor cooling by liquid metal. The outcomes of the research are: (1) A calculation algorithm was derived for obtaining convergent conditions by repeating nuclear characteristic calculation and thermal flow characteristic calculation for the space nuclear reactor. (2) Use of this algorithm and the parametric study established that a space nuclear reactor using 97% enriched uranium nitride as the fuel and lithium as the coolant and having a core with a radius of about 25 cm, a height of about 50 cm and a generation efficiency of about 7% can probably be operated continuously for at least more than ten years at 100 kW only by reactivity control by rotary reflector. (3) A new CAD/CAE system was developed to assist design work to optimize the core characteristics of the space nuclear reactor comprehensively. It is composed of the integrated design support system VINDS using virtual reality and the distributed system WINDS to collaboratively support design work using Internet. (N.H.)

  16. Creating a classroom culture that supports the common core teaching questioning, conversation techniques, and other essential skills

    CERN Document Server

    Harris, Bryan

    2014-01-01

    Is your classroom culture conducive to the expectations of the Common Core? Teaching content is not enough; students need a classroom structure and atmosphere that will help them learn key academic skills. This practical book will show you how to transform your classroom culture, raise the level of rigor, encourage higher-level questioning and critical thinking, and promote academic discussions. You will also find out how to adjust your classroom management techniques so that students learn to regulate themselves while completing these higher-level tasks. Special Features in Each Chapter: Key Idea-a summary of the essential idea that will be addressed in the chapter Practical strategies-a variety of easy-to-implement ideas that you can try right away Connections to the Common Core State Standards-how the skills taught in this book will help students meet the standards Reflection Questions-thoughtful questions that will help teachers apply their learning to their own classrooms. These questions can be answered...

  17. PBDOWN - a computer code for simulating core material discharge and thermal to mechanical energy conversion in LMFBR hypothetical accidents

    International Nuclear Information System (INIS)

    Royl, P.

    1981-01-01

    PBDOWN is a computer code that simulates the blowdown of confined boiling materials ('pools') into a colder upper coolant plenum as time dependent ejection and expansion with consideration of a few selected exchange processes. Its application is restricted to situations resulting from hypothetical loss of flow (LOF) accidents in LMFBR's, where enough voiding has occured, that in core sodium vapor pressures become negligible. PBDOWN considers one working fluid for the discharge process (either fuel or steel) and a maximum of two working fluids (either fuel and sodium or steel and sodium) for the expansion process in the upper coolant plenum. Entrainment of sodium at the accelerated bubble liquid interfaces is mechanistically calculated by a Taylor instability entrainment model. Simulation of a hemispherical expansion form together with this mechanistic entrainment model gives a new integrated calculation of the time dependent sodium mass in the bubble. The paper summarizes the basic equations and assumptions of this computer model. Sample results compare different heat transfer and Na entrainment models during steel and fuel driven discharge processes. Mechanistic sodium entrainment simulation for SNR-type reactors coupled with a realistic heat transfer model is shown to reduce the integral mechanical work potential by a factor of 1.3 to 2.0 over the isentropic energy of the discharge working fluids. (orig.)

  18. Information Technology Management: Course Re-Design Using an Assessment Driven Approach

    Science.gov (United States)

    Schwieger, Dana; Surendran, Ken

    2013-01-01

    One of the core courses in the IS2010 Model Curriculum Guideline is "IS Strategy, Management and Acquisition" ("ISMA"). The authors redesigned their pre-IS2010 model Information Technology Management (ITM) course to meet the skills development stated in the ISMA course. Since the IT discipline is changing rapidly, the technical…

  19. Towards redesigning indigenous mung bean foods

    NARCIS (Netherlands)

    Dahiya, P.K.

    2013-01-01

    Redesigning traditional foods requires consideration of the various factors affecting the nutrient intake from such foods. Amongst these factors are adequate consumption, proper nutrient bioavailability and consumer satisfaction. These factors are related to traditional food quality at various

  20. Reactor core

    International Nuclear Information System (INIS)

    Azekura, Kazuo; Kurihara, Kunitoshi.

    1992-01-01

    In a BWR type reactor, a great number of pipes (spectral shift pipes) are disposed in the reactor core. Moderators having a small moderating cross section (heavy water) are circulated in the spectral shift pipes to suppress the excess reactivity while increasing the conversion ratio at an initial stage of the operation cycle. After the intermediate stage of the operation cycle in which the reactor core reactivity is lowered, reactivity is increased by circulating moderators having a great moderating cross section (light water) to extend the taken up burnup degree. Further, neutron absorbers such as boron are mixed to the moderator in the spectral shift pipe to control the concentration thereof. With such a constitution, control rods and driving mechanisms are no more necessary, to simplify the structure of the reactor core. This can increase the fuel conversion ratio and control great excess reactivity. Accordingly, a nuclear reactor core of high conversion and high burnup degree can be attained. (I.N.)

  1. Modification of Ga2O3 by an Ag-Cr core-shell cocatalyst enhances photocatalytic CO evolution for the conversion of CO2 by H2O.

    Science.gov (United States)

    Pang, Rui; Teramura, Kentaro; Tatsumi, Hiroyuki; Asakura, Hiroyuki; Hosokawa, Saburo; Tanaka, Tsunehiro

    2018-01-25

    A core-shell structure of Ag-Cr dual cocatalyst loaded-Ga 2 O 3 was found to significantly enhance the formation rate of CO and selectivity toward CO evolution for the photocatalytic conversion of CO 2 where H 2 O is used as an electron donor.

  2. n-GaAs/InGaP/p-GaAs core-multishell nanowire diodes for efficient light-to-current conversion

    Energy Technology Data Exchange (ETDEWEB)

    Gutsche, Christoph; Lysov, Andrey; Regolin, Ingo; Keller, Gregor; Prost, Werner; Tegude, Franz-Josef [Department of Solid-State Electronics and CeNIDE University of Duisburg-Essen, Duisburg (Germany); Braam, Daniel; Li, Zi-An; Geller, Martin; Spasova, Marina [Department of Experimental Physics and CeNIDE University of Duisburg-Essen, Duisburg (Germany)

    2012-03-07

    Heterostructure n-GaAs/InGaP/p-GaAs core-multishell nanowire diodes are synthesized by metal-organic vapor-phase epitaxy. This structure allows a reproducible, selective wet etching of the individual shells and therefore a simplified contacting of single nanowire p-i-n junctions. Nanowire diodes show leakage currents in a low pA range and at a high rectification ratio of 3500 (at {+-}1V). Pronounced electroluminescence at 1.4 eV is measured at room temperature and gives evidence of the device quality. Photocurrent generation is demonstrated at the complete area of the nanowire p-i-n junction by scanning photocurrent microscopy. A solar-conversion efficiency of 4.7%, an open-circuit voltage of 0.5 V and a fill factor of 52% are obtained under AM 1.5G conditions. These results will guide the development of nanowire-based photonic and photovoltaic devices. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. Core Conversations with Educative Dragging

    Science.gov (United States)

    Wanko, Jeffrey J.; Edwards, Michael Todd; Phelps, Steve

    2012-01-01

    The Sliding along a Side task was presented at a National Council of Teachers of Mathematics (NCTM) conference session for high school teachers. According to the authors, while exploring this task with this group of experienced mathematics educators and classroom teachers, they shared a "gasp!" moment. With the aid of the dynamic mathematics…

  4. Reactor Physics Methods and Preconceptual Core Design Analyses for Conversion of the Advanced Test Reactor to Low-Enriched Uranium Fuel Annual Report for Fiscal Year 2012

    Energy Technology Data Exchange (ETDEWEB)

    David W. Nigg; Sean R. Morrell

    2012-09-01

    Under the current long-term DOE policy and planning scenario, both the ATR and the ATRC will be reconfigured at an appropriate time within the next several years to operate with low-enriched uranium (LEU) fuel. This will be accomplished under the auspices of the Reduced Enrichment Research and Test Reactor (RERTR) Program, administered by the DOE National Nuclear Security Administration (NNSA). At a minimum, the internal design and composition of the fuel element plates and support structure will change, to accommodate the need for low enrichment in a manner that maintains total core excess reactivity at a suitable level for anticipated operational needs throughout each cycle while respecting all control and shutdown margin requirements and power distribution limits. The complete engineering design and optimization of LEU cores for the ATR and the ATRC will require significant multi-year efforts in the areas of fuel design, development and testing, as well as a complete re-analysis of the relevant reactor physics parameters for a core composed of LEU fuel, with possible control system modifications. Ultimately, revalidation of the computational physics parameters per applicable national and international standards against data from experimental measurements for prototypes of the new ATR and ATRC core designs will also be required for Safety Analysis Report (SAR) changes to support routine operations with LEU. This report is focused on reactor physics analyses conducted during Fiscal Year (FY) 2012 to support the initial development of several potential preconceptual fuel element designs that are suitable candidates for further study and refinement during FY-2013 and beyond. In a separate, but related, effort in the general area of computational support for ATR operations, the Idaho National Laboratory (INL) is conducting a focused multiyear effort to introduce modern high-fidelity computational reactor physics software and associated validation protocols to replace

  5. A strategic planning methodology for aircraft redesign

    Science.gov (United States)

    Romli, Fairuz Izzuddin

    Due to a progressive market shift to a customer-driven environment, the influence of engineering changes on the product's market success is becoming more prominent. This situation affects many long lead-time product industries including aircraft manufacturing. Derivative development has been the key strategy for many aircraft manufacturers to survive the competitive market and this trend is expected to continue in the future. Within this environment of design adaptation and variation, the main market advantages are often gained by the fastest aircraft manufacturers to develop and produce their range of market offerings without any costly mistakes. This realization creates an emphasis on the efficiency of the redesign process, particularly on the handling of engineering changes. However, most activities involved in the redesign process are supported either inefficiently or not at all by the current design methods and tools, primarily because they have been mostly developed to improve original product development. In view of this, the main goal of this research is to propose an aircraft redesign methodology that will act as a decision-making aid for aircraft designers in the change implementation planning of derivative developments. The proposed method, known as Strategic Planning of Engineering Changes (SPEC), combines the key elements of the product redesign planning and change management processes. Its application is aimed at reducing the redesign risks of derivative aircraft development, improving the detection of possible change effects propagation, increasing the efficiency of the change implementation planning and also reducing the costs and the time delays due to the redesign process. To address these challenges, four research areas have been identified: baseline assessment, change propagation prediction, change impact analysis and change implementation planning. Based on the established requirements for the redesign planning process, several methods and

  6. Synthesis and green up-conversion fluorescence of colloidal La0.78Yb0.20Er0.02F3/SiO2 core/shell nanocrystals

    International Nuclear Information System (INIS)

    Wang Yan; Qin Weiping; Zhang Jisen; Cao Chunyan; Zhang Jishuang; Jin Ye; Zhu Peifen; Wei Guodong; Wang Guofeng; Wang Lili

    2007-01-01

    Water-soluble PVP-stabilized hexagonal-phase La 0.78 Yb 0.20 Er 0.02 F 3 nanocrystals (NCs) were synthesized by hydrothermal method. The NCs were coated with a very thin silica shell, and amino groups were introduced to the surface of silica shells by copolymerization of 3-aminopropyl(triethoxy)silane. The core/shell NCs can be dispersed in ethanol and water to form stable colloidal solution. The transmission electron microscopy (TEM), selected area electron diffraction (SAED), powder X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FT-IR) were used to characterize the core/shell materials. In addition, the green up-conversion fluorescence mechanism of La 0.78 Yb 0.20 Er 0.02 F 3 /SiO 2 NCs was studied with a 980-nm diode laser as excitation source. The water solubility, small core/shell particles size, and well colloidal stability mean the green up-conversion fluorescence NCs have potential applications in bioassay. - Graphical abstract: Colloidal La 0.78 Yb 0.20 Er 0.02 F 3 /SiO 2 Core/Shell nanocrystals (NCs) were synthesized and the free amino groups were introduced to the surface of silica shells by copolymerization 3-aminopropyl(triethoxy)silane. The NCs can be dispersed in ethanol and water to form stable colloidal solution. In addition, the NCs exhibit green up-conversion fluorescence under 980-nm excitation

  7. Grid Computing BOINC Redesign Mindmap with incentive system (gamification)

    OpenAIRE

    Kitchen, Kris

    2016-01-01

    Grid Computing BOINC Redesign Mindmap with incentive system (gamification) this is a PDF viewable of https://figshare.com/articles/Grid_Computing_BOINC_Redesign_Mindmap_with_incentive_system_gamification_/1265350

  8. Course Redesign: An Evidence-Based Approach

    Science.gov (United States)

    Nomme, Kathy; Birol, Gülnur

    2014-01-01

    A first year non-majors biology course, with an enrollment of around 440 students, has been redesigned from a course of traditional content and teaching style to one that emphasizes biological concepts in current global issues and incorporates active learning strategies. We were informed by the education literature incorporating many aspects of…

  9. Mandated Preparation Program Redesign: Kentucky Case

    Science.gov (United States)

    Browne-Ferrigno, Tricia

    2013-01-01

    This case study presents a chronicle of events spanning a decade in Kentucky that led to state policy changes for principal preparation and details the response to those mandated changes by professors at the University of Kentucky. Professors' collaborative efforts resulted in a new teacher leadership program and redesigned principal certification…

  10. High School Redesign Gets Presidential Lift

    Science.gov (United States)

    Adams, Caralee J.

    2013-01-01

    President Barack Obama applauded high school redesign efforts in his State of the Union address and encouraged districts to look to successful models for inspiration. Last week, he followed up with a request in his fiscal 2014 budget proposal for a new, $300 million competitive-grant program. Recognition is widespread that high schools need to…

  11. RSA Monitoring Redesign Initiative Informational Booklet #1

    Science.gov (United States)

    US Department of Education, 2005

    2005-01-01

    This informational booklet contains background materials regarding the Rehabilitation Services Administration (RSA) initiative to redesign its monitoring system. The booklet is intended to expand the knowledge and understanding of those individuals selected to participate in the RSA-sponsored monitoring conference that was held August 24 and 25,…

  12. RSA Monitoring Redesign Initiative Informational Booklet #2

    Science.gov (United States)

    US Department of Education, 2005

    2005-01-01

    The U.S. Department of Education's Rehabilitation Services Administration (RSA) is undertaking a major initiative to substantially redesign its program monitoring and improvement system. The overriding goal is to improve vocational rehabilitation (VR) services and employment outcomes for individuals with disabilities through the development of a…

  13. Curriculum Redesign in Veterinary Medicine: Part I.

    Science.gov (United States)

    Chaney, Kristin P; Macik, Maria L; Turner, Jacqueline S; Korich, Jodi A; Rogers, Kenita S; Fowler, Debra; Scallan, Elizabeth M; Keefe, Lisa M

    Curricular review is considered a necessary component for growth and enhancement of academic programs and requires time, energy, creativity, and persistence from both faculty and administration. At Texas A&M College of Veterinary Medicine & Biomedical Sciences (TAMU), the faculty and administration partnered with the university's Center for Teaching Excellence to create a faculty-driven, data-enhanced curricular redesign process. The 8-step process begins with the formation of a dedicated faculty curriculum design team to drive the redesign process and to support the college curriculum committee. The next steps include defining graduate outcomes and mapping the current curriculum to identify gaps and redundancies across the curriculum. Data are collected from internal and external stakeholders including veterinary students, faculty, alumni, and employers of graduates. Data collected through curriculum mapping and stakeholder engagement substantiate the curriculum redesign. The guidelines, supporting documents, and 8-step process developed at TAMU are provided to assist other veterinary schools in successful curricular redesign. This is the first of a two-part report that provides the background, context, and description of the process for charting the course for curricular change. The process involves defining expected learning outcomes for new graduates, conducting a curriculum mapping exercise, and collecting stakeholder data for curricular evaluation (steps 1-4). The second part of the report describes the development of rubrics that were applied to the graduate learning outcomes (steps 5-8) and engagement of faculty during the implementation phases of data-driven curriculum change.

  14. Re-Designing Business Card Advertisements.

    Science.gov (United States)

    Schaub, Laura

    2001-01-01

    Discusses ways to turn information from a business card into an advertisement to be placed in a student publication. Addresses visual interest, typography, and other design issues. Includes several sample advertisements and a classroom activity involving redesigning a business card into an advertisement. (RS)

  15. A Flipped Classroom Redesign in General Chemistry

    Science.gov (United States)

    Reid, Scott A.

    2016-01-01

    The flipped classroom continues to attract significant attention in higher education. Building upon our recent parallel controlled study of the flipped classroom in a second-term general chemistry course ("J. Chem. Educ.," 2016, 93, 13-23), here we report on a redesign of the flipped course aimed at scaling up total enrollment while…

  16. Implementing a Redesign Strategy: Lessons from Educational Change.

    Science.gov (United States)

    Basom, Richard E., Jr.; Crandall, David P.

    The effective implementation of school redesign, based on a social systems approach, is discussed in this paper. A basic assumption is that the interdependence of system elements has implications for a complex change process. Seven barriers to redesign and five critical issues for successful redesign strategy are presented. Seven linear steps for…

  17. Effective healthcare process redesign through an interdisciplinary team approach.

    Science.gov (United States)

    Snyder, Rita; Huynh, Nathan; Cai, Bo; Vidal, José; Bennett, Kevin

    2013-01-01

    Healthcare process redesign is a complex and often high risk undertaking. Typically, there is a limited understanding of the baseline process and often inadequate tools by which to assess it. This can be confounded by narrow redesign team expertise that can result in unanticipated and/or unintended redesign consequences. Interdisciplinary research teams of healthcare, biostatistics, engineering and computer science experts provide broad support for a more effective and safer approach to healthcare process redesign. We describe an interdisciplinary research team focused on medication administration process (MAP)redesign and its achievements and challenges.

  18. Including product features in process redesign

    DEFF Research Database (Denmark)

    Hvam, Lars; Hauksdóttir, Dagný; Mortensen, Niels Henrik

    2017-01-01

    do not take into account how the product features are applied throughout the process, which makes it difficult to obtain a comprehensive understanding of the activities in the processes and to generate significant improvements. The suggested approach models the product family using the so......This article suggests a visual modelling method for integrating models of product features with business process models for redesigning the business processes involving specifications of customer-tailored products and services. The current methods for redesigning these types of business processes......-called product variant master and the business process modelling notation for modelling the process flow. The product model is combined with the process map by identifying features used in each step of the process flow. Additionally, based on the information absorbed from the integrated model, the value stream...

  19. Accounting for future redesign to balance performance and development costs

    International Nuclear Information System (INIS)

    Villanueva, D.; Haftka, R.T.; Sankar, B.V.

    2014-01-01

    Most components undergo tests after they are designed and are redesigned if necessary. Tests help designers find unsafe and overly conservative designs, and redesign can restore safety or increase performance. In general, the expected changes to the performance and reliability of the design after the test and redesign are not considered. In this paper, we explore how modeling a future test and redesign provides a company an opportunity to balance development costs versus performance by simultaneously designing the design and the post-test redesign rules during the initial design stage. Due to regulations and tradition, safety margin and safety factor based design is a common practice in industry as opposed to probabilistic design. In this paper, we show that it is possible to continue to use safety margin based design, and employ probability solely to select safety margins and redesign criteria. In this study, we find the optimum safety margins and redesign criterion for an integrated thermal protection system. These are optimized in order to find a minimum mass design with minimal redesign costs. We observed that the optimum safety margin and redesign criterion call for an initially conservative design and use the redesign process to trim excess weight rather than restore safety. This would fit well with regulatory constraints, since regulations usually impose minimum safety margins. - Highlights: • Modeling future tests and redesign allows balancing performance and development cost. • We optimize safety margins and redesign criteria for desired balance. • We design with safety margins, with probabilistic optimization to decide the margins. • Redesign also allowed the trade-off of conservativeness and performance. • In our case it paid to be conservative initially but redesign for more

  20. Theoretical studies aiming at the IEA-R1 reactor core conversion from high U-235 enrichment to low U-235 enrichment

    International Nuclear Information System (INIS)

    Frajndlich, R.

    1982-01-01

    The research reactors, of which the fuel elements are of MTR type, functions presently, almost in their majority with high U-235 enrichment. The fear that those fuel elements might generate a considerabLe proliferation of nuclear weapons rendered almost mandatory the conversion of highly enriched fuel elements to a low U-235 enrichment. As the IEA-R1 reactor of IPEN is operating with highly enriched fuel elements a study aiming at this conversion was done. The problems related to the conversion and the results obtained, demonstrated the technical viabilty for its realization. (E.G.) [pt

  1. Designing and redesigning medical telecare services: a forces-oriented model.

    Science.gov (United States)

    Gortzis, L G

    2007-01-01

    Medical telecare services' designing and redesigning still remains a challenging issue since it often depends on how a number of socio-technological issues are framed. This work has two key objectives; the former is to theoretically analyze the nature of a telecare environment by developing a model that reveals potential areas of analysis and the latter is to support designing and redesigning medical telecare services by formulating a strategy as well as a number of 'state of the art' guidelines. We have extended Leavitt's diamond to develop a model capable of accurately reflecting the telecare environment building dimensions as well as their interactions. This model depends on the i) technology, ii) collaborators, iii) tasks, iv) structure, v) social forces, and the vi) procedure dimensions. Taking this model as a core element we have proposed a service designing and redesigning strategy formulating, in parallel, six scalable dimension-oriented guidelines. During the two-year period (2003-2005) an enormous amount of data was collected (by active participating in two EU projects, by conducting semistructured interviews, by performing onsite observations as well as by reviewing 78 previous projects) and classified, structuring six guidelines. These guidelines can be considered as the 'state of the art' to support future services' design and redesign. This work considering the telecare environment as a multi-dimensional, operational organization has put the focus on accurate telecare services' design and redesign. The parameters are not limited, by any means, and are drawn from experience of designing services in a variety of telecare domains. The optimal parameter combination must be chosen according to the aim of each telecare procedure. Further research is needed to determine the minimum parameters to support telecare service design.

  2. Enhancing policy innovation by redesigning representative democracy

    DEFF Research Database (Denmark)

    Sørensen, Eva

    2016-01-01

    Policy innovation is a key aspect of public innovation, which has been largely overlooked. Political leadership, competition and collaboration are key drivers of policy innovation. It is a barrier in traditional models of representative democracy that they provide weak conditions for collaboration....... Two Danish case studies indicate that collaboration between politicians and relevant and affected stakeholders can promote policy innovation, but also that a redesign of representative democracy is needed in order to establish a productive combination of political leadership, competition...... and collaboration in political life....

  3. Redesigning Health Information Systems in Developing Countries

    DEFF Research Database (Denmark)

    Mengiste, Shegaw Anagaw; Kimaro, Honest; Aanestad, Margunn

    2008-01-01

    or no end user involvement results in a centralised HIS with an extensive, somewhat inappropriate, but also inflexible set of standards. Consequently, the HIS is not very useful for the wished-for decentralisation of health services, and there is an urgent need to redesign the existing HIS in order to make...... degree of control over a decentralised HIS, including budgets and the use of resources, should be delegated to the district administration. In order to achieve the aim of a locally relevant, well-working HIS, it is necessary that appropriate authority, capacity and decentralised allocation of resources...

  4. Redesigning Manufacturing Footprint from Dynamic Perspective

    DEFF Research Database (Denmark)

    Yang, Cheng; Farooq, Sami; Johansen, John

    2009-01-01

    footprint to address the constantly emerging new challenges by giving a holistic approach from dynamic perspective. Three Danish companies are presented. The way they developed their international manufacturing networks is analysed historically, and their redesigning of manufacturing footprint is expressed...... as how to re-assign portfolios of products and processes between specific plants within the same manufacturing network at one point in time. The strategic factors that have impact on such decisions are discussed and classified into two groups. Last, a holistic framework and a process model is presented...

  5. Finance leadership imperatives in clinical redesign.

    Science.gov (United States)

    Harris, John; Holm, Craig E; Inniger, Meredith C

    2015-03-01

    As physicians embrace their roles in managing healthcare costs and quality, finance leaders should seize the opportunity to engage physicians in clinical care redesign to ensure both high-quality performance and efficient resource use. Finance leaders should strike a balance between risk and reward to achieve a portfolio of clinical initiatives that is organizationally sustainable and responsive to current external drivers of payment changes. Because these initiatives should be driven by physicians, the new skill set of finance leaders should include an emphasis on relationship building to achieve consensus and drive change across an organization.

  6. Development of redesign method of production system based on QFD

    Science.gov (United States)

    Kondoh, Shinsuke; Umeda, Yasusi; Togawa, Hisashi

    In order to catch up with rapidly changing market environment, rapid and flexible redesign of production system is quite important. For effective and rapid redesign of production system, a redesign support system is eagerly needed. To this end, this paper proposes a redesign method of production system based on Quality Function Deployment (QFD). This method represents a designer's intention in the form of QFD, collects experts' knowledge as “Production Method (PM) modules,” and formulates redesign guidelines as seven redesign operations so as to support a designer to find out improvement ideas in a systematical manner. This paper also illustrates a redesign support tool of a production system we have developed based on this method, and demonstrates its feasibility with a practical example of a production system of a contact probe. A result from this example shows that comparable cost reduction to those of veteran designers can be achieved by a novice designer. From this result, we conclude our redesign method is effective and feasible for supporting redesign of a production system.

  7. Best practices in business process redesign: an overview and qualitative evaluation of successful redesign heuristics

    NARCIS (Netherlands)

    Reijers, H.A.; Limam Mansar, S.

    2005-01-01

    To implement business process redesign several best practices can be distinguished. This paper gives an overview of heuristic rules that can support practitioners to develop a business process design that is a radical improvement of a current design. The emphasis is on the mechanics of the process,

  8. Optimizing enactment of nursing roles: redesigning care processes and structures

    Directory of Open Access Journals (Sweden)

    Jackson K

    2014-02-01

    Full Text Available Karen Jackson,1 Deborah E White,2 Jeanne Besner,1 Jill M Norris21Health Systems and Workforce Research Unit, Alberta Health Services, Calgary, Alberta, Canada; 2Faculty of Nursing, University of Calgary, Calgary, Alberta, CanadaBackground: Effective and efficient use of nursing human resources is critical. The Nursing Role Effectiveness Model conceptualizes nursing practice in terms of key clinical role accountabilities and has the potential to inform redesign efforts. The aims of this study were to develop, implement, and evaluate a job redesign intended to optimize the enactment of registered nurse (RN clinical role accountabilities.Methods: A job redesign was developed and implemented in a single medical patient care unit, the redesign unit. A mixed-methods design was used to evaluate the job redesign; a second medical patient care unit served as a control unit. Data from administrative databases, observations, interviews, and demographic surveys were collected pre-redesign (November 2005 and post-redesign (October 2007.Results: Several existing unit structures and processes (eg, model of care delivery influenced RNs' ability to optimally enact their role accountabilities. Redesign efforts were hampered by contextual issues, including organizational alignment, leadership, and timing. Overall, optimized enactment of RN role accountabilities and improvements to patient outcomes did not occur, yet this was predictable, given that the redesign was not successful. Although the results were disappointing, much was learned about job redesign.Conclusion: Potential exists to improve the utilization of nursing providers by situating nurses' work in a clinical role accountability framework and attending to a clear organizational vision and well-articulated strategic plan that is championed by leaders at all levels of the organization. Health care leaders require a clear understanding of nurses' role accountabilities, support in managing change, and

  9. Do the Math: Course Redesign's Impact on Learning and Scheduling

    Science.gov (United States)

    Squires, John; Faulkner, Jerry; Hite, Carl

    2009-01-01

    The math department at Cleveland State Community College embarked upon course redesign in 2008. As a result of this project, student engagement, learning, and success rates have increased dramatically. By including both developmental and college level math courses in the redesign, the department has been able to implement innovative scheduling and…

  10. Evaluation of the Redesign of an Undergraduate Cell Biology Course

    Science.gov (United States)

    McEwen, Laura April; Harris, dik; Schmid, Richard F.; Vogel, Jackie; Western, Tamara; Harrison, Paul

    2009-01-01

    This article offers a case study of the evaluation of a redesigned and redeveloped laboratory-based cell biology course. The course was a compulsory element of the biology program, but the laboratory had become outdated and was inadequately equipped. With the support of a faculty-based teaching improvement project, the teaching team redesigned the…

  11. Controlling Curriculum Redesign with a Process Improvement Model

    Science.gov (United States)

    Drinka, Dennis; Yen, Minnie Yi-Miin

    2008-01-01

    A portion of the curriculum for a Management Information Systems degree was redesigned to enhance the experiential learning of students by focusing it on a three-semester community-based system development project. The entire curriculum was then redesigned to have a project-centric focus with each course in the curriculum contributing to the…

  12. 76 FR 16233 - Interpretive Rule Regarding Electronic Contributor Redesignations

    Science.gov (United States)

    2011-03-23

    ... audit, the Commission recently determined that a specific redesignation practice provided the same degree of assurance of the contributor's identity and the contributor's intent to redesignate the... that this process provided assurance of contributor identity and intent equivalent to a written...

  13. Main activities carried out for the conversion of the reactor core TRIGA, from HEU 8.5/70 / LEU 8.5/20 to LEU 30/20; Principales actividades llevadas a cabo para la conversion del nucleo del reactor TRIGA, de HEU 8.5/70 / LEU 8.5/20 a LEU 30/20

    Energy Technology Data Exchange (ETDEWEB)

    Flores C, J., E-mail: jorge.floresc@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2012-10-15

    In agreement with the policies of the global initiative of threats reduction (GTRI), Mexico committed that inside the reduction program of the fuel enrichment in research and test reactors (RERTR), the conversion of the core reactor TRIGA (in the nuclear centre) would be made, to use solely fuel with low enrichment ({<=} 20% U{sup 235}). To support to the execution of this commitment, a series of accords and agreements were established. The Project Agreement and Supply among the IAEA, the United States of America and Mexico was the more relevant. In this work the main activities carried out in the Instituto Nacional de Investigaciones Nucleares (ININ) with this purpose are presented. (Author)

  14. Benefits of Silica Core-Shell Structures on the Temperature Sensing Properties of Er,Yb:GdVO4 Up-Conversion Nanoparticles.

    Science.gov (United States)

    Savchuk, Oleksandr A; Carvajal, Joan J; Cascales, C; Aguiló, M; Díaz, F

    2016-03-23

    We studied the temperature-dependent luminescence of GdVO4 nanoparticles co-doped with Er(3+) (1 mol %) and Yb(3+) (20 mol %) and determined their thermal sensing properties through the fluorescence intensity ratio (FIR) technique. We also analyzed how a silica coating, in a core-shell structure, affects the temperature sensing properties of this material. Spectra were recorded in the range of biological temperatures (298-343 K). The absolute sensitivity for temperature determination calculated for the core-shell nanoparticles is double the one calculated for bare nanoparticles, achieving a thermal resolution of 0.4 K. Moreover, silica-coated nanoparticles show good dispersibility in different solvents, such as water, DMSO, and methanol. Also, they show good luminescence stability without interactions with solvent molecules. Furthermore, we also observed that the silica coating shell prevents progressive heating of the nanoparticles during prolonged excitation periods with the 980 nm laser, preventing effects on their thermometric applications.

  15. A redesign of OGC Symbology Encoding standard for sharing cartography

    Directory of Open Access Journals (Sweden)

    Erwan Bocher

    2018-01-01

    Full Text Available Despite most Spatial Data Infrastructures offering service-based visualization of geospatial data, requirements are often at a very basic level leading to poor quality of maps. This is a general observation for any geospatial architecture as soon as open standards as those of the Open Geospatial Consortium (OGC are applied. To improve the situation, this paper does focus on improvements at the portrayal interoperability side by considering standardization aspects. We propose two major redesign recommendations. First to consolidate the cartographic theory at the core of the OGC Symbology Encoding standard. Secondly to build the standard in a modular way so as to be ready to be extended with upcoming future cartographic requirements. Thus, we start by defining portrayal interoperability by means of typical-use cases that frame the concept of sharing cartography. Then we bring to light the strengths and limits of the relevant open standards to consider in this context. Finally we propose a set of recommendations to overcome the limits so as to make these use cases a true reality. Even if the definition of a cartographic-oriented standard is not able to act as a complete cartographic design framework by itself, we argue that pushing forward the standardization work dedicated to cartography is a way to share and disseminate good practices and finally to improve the quality of the visualizations.

  16. Freely flowing conversations

    DEFF Research Database (Denmark)

    Aakjær, Marie Kirstejn; Andrade, David; Dexters, Peter

    and in regards to rehabilitation efforts. In the context of prisons UDI is inspired by the complexity approach (Stacey 2005). We seek to facilitate freely flowing conversations between inmates, staff and managers – pushing the boundaries of existing norms, roles and beliefs. In the end however we rely...... relations by changing conversations. Through the theoretical framework of the complexity approach, we discuss how this may lead to organizational change. Finally we suggest that inviting inmates to take part in conversations about core organizational development may be a fundamental strategy in trying...

  17. Redesign of a Low Energy Probe Head

    CERN Document Server

    Rao, Yi-Nong; Ries, Thomas

    2005-01-01

    The present situation of the low energy probe LE2 in TRIUMF cyclotron is that the thickness of the finger 5 is uniform over a radial length of 3.25 inch and its weight which amounts to ~447 g is affecting its re-circulating ball mechanism and causing it to fall below the median plane over its range of movement. We therefore re-design it in order to reduce its weight. First, we made simulations and determined the optimum thickness of the probe head vs its radial length. These simulation results are found to be in good agreement with experimental measurements made. Finally, we calculated the temperature rise caused by the beam power dumped on the probe, and figured out the maximum current of beam that can be dumped on the finger.

  18. Safety in the redesigning of production lines

    DEFF Research Database (Denmark)

    Dyhrberg, Mette Bang; Broberg, Ole; Jacobsen, Peter

    2006-01-01

    This paper is a case study report on how safety considerations were handled in the process of redesigning a production line. The design process was characterized as a specification and negotiation process between engineers from the company and the supplier organization. The new production line...... became safer, but not as a result of any intentional plan to integrate safety aspects into the design process. Instead, the supplier’s design of a new piece of equipment had a higher built-in safety level. The engineering team in the company was aware of the importance of safety aspects neither...... in the specification material nor in their face-to-face meetings with the supplier. Safety aspects were not part of their work practice. On this basis, it was suggested that formal guidelines or procedures for integrating safety in the design of production lines would have no effect. Instead, the researchers set up...

  19. Redesign of the Human Metabolic Simulator

    Science.gov (United States)

    Duffield, Bruce; Jeng, Frank; Lange, Kevin

    2004-01-01

    The National Aeronautics and Space Administration (NASA) is currently building a Human Metabolic Simulator (HMS) at the Johnson Space Center as part of the Advanced Life Support Air Revitalization Technology Evaluation Facility (ARTEF). The purpose of ARTEF is to evaluate Environmental Control and Life Support System Technologies for Advanced Missions. The HMS is needed to reproduce the primary metabolic effects of human respiration on an enclosed atmosphere when humans cannot be present and the impact of human presence on the system is required. A HMS was designed, built and successfully operated in 2000 but larger crew size requirements and the expense of upgrade of the current system necessitate redesign. This paper addresses the redesign. Several concepts were considered, ranging from chemical oxidation of a hydrocarbon like ethanol or ethyl acetate to carbon dioxide and water, oxidation of an iron-containing compound, or by using a fuel cell. For reasons of cost, simplicity, safety and other factors, the concept chosen includes: a molecular sieve packaged as an industrial oxygen concentrator to remove oxygen from the atmosphere, with direct carbon dioxide, water and heat injection. The water injection is done via heating water to steam with a heat exchanger and thermal effects are handled by directly adding heat to the air stream with a second heat exchanger. Both heat exchangers are supplied by a hot oil loop. The amount of oxygen removal, carbon dioxide addition, water addition and heat addition were calculated using metabolic profiles for respiration and heat, calculated using a series of empirical equations developed for International Space Station (ISS). Sketches of the Human Metabolic Simulator and the hot oil bath loop used to supply heat to the heat exchangers are included

  20. Research of natural resources saving by design studies of Pressurized Light Water Reactors and High Conversion PWR cores with mixed oxide fuels composed of thorium/uranium/plutonium

    International Nuclear Information System (INIS)

    Vallet, V.

    2012-01-01

    Within the framework of innovative neutronic conception of Pressurized Light Water Reactors (PWR) of 3. generation, saving of natural resources is of paramount importance for sustainable nuclear energy production. This study consists in the one hand to design high Conversion Reactors exploiting mixed oxide fuels composed of thorium/uranium/plutonium, and in the other hand, to elaborate multi-recycling strategies of both plutonium and 233 U, in order to maximize natural resources economy. This study has two main objectives: first the design of High Conversion PWR (HCPWR) with mixed oxide fuels composed of thorium/uranium/plutonium, and secondly the setting up of multi-recycling strategies of both plutonium and 233 U, to better natural resources economy. The approach took place in four stages. Two ways of introducing thorium into PWR have been identified: the first is with low moderator to fuel volume ratios (MR) and ThPuO 2 fuel, and the second is with standard or high MR and ThUO 2 fuel. The first way led to the design of under-moderated HCPWR following the criteria of high 233 U production and low plutonium consumption. This second step came up with two specific concepts, from which multi-recycling strategies have been elaborated. The exclusive production and recycling of 233 U inside HCPWR limits the annual economy of natural uranium to approximately 30%. It was brought to light that the strong need in plutonium in the HCPWR dedicated to 233 U production is the limiting factor. That is why it was eventually proposed to study how the production of 233 U within PWR (with standard MR), from 2020. It was shown that the anticipated production of 233 U in dedicated PWR relaxes the constraint on plutonium inventories and favours the transition toward a symbiotic reactor fleet composed of both PWR and HCPWR loaded with thorium fuel. This strategy is more adapted and leads to an annual economy of natural uranium of about 65%. (author) [fr

  1. An integrated lean-methods approach to hospital facilities redesign.

    Science.gov (United States)

    Nicholas, John

    2012-01-01

    Lean production methods for eliminating waste and improving processes in manufacturing are now being applied in healthcare. As the author shows, the methods are appropriate for redesigning hospital facilities. When used in an integrated manner and employing teams of mostly clinicians, the methods produce facility designs that are custom-fit to patient needs and caregiver work processes, and reduce operational costs. The author reviews lean methods and an approach for integrating them in the redesign of hospital facilities. A case example of the redesign of an emergency department shows the feasibility and benefits of the approach.

  2. Development and Application of a Stepwise Assessment Process for Rational Redesign of Sequential Skills-Based Courses.

    Science.gov (United States)

    Gallimore, Casey E; Porter, Andrea L; Barnett, Susanne G

    2016-10-25

    Objective. To develop and apply a stepwise process to assess achievement of course learning objectives related to advanced pharmacy practice experiences (APPEs) preparedness and inform redesign of sequential skills-based courses. Design. Four steps comprised the assessment and redesign process: (1) identify skills critical for APPE preparedness; (2) utilize focus groups and course evaluations to determine student competence in skill performance; (3) apply course mapping to identify course deficits contributing to suboptimal skill performance; and (4) initiate course redesign to target exposed deficits. Assessment. Focus group participants perceived students were least prepared for skills within the Accreditation Council for Pharmacy Education's pre-APPE core domains of Identification and Assessment of Drug-related Problems and General Communication Abilities. Course mapping identified gaps in instruction, performance, and assessment of skills within aforementioned domains. Conclusions. A stepwise process that identified strengths and weaknesses of a course, was used to facilitate structured course redesign. Strengths of the process included input and corroboration from both preceptors and students. Limitations included feedback from a small number of pharmacy preceptors and increased workload on course coordinators.

  3. The redesigned Bulletin is on its way

    CERN Multimedia

    2006-01-01

    In May, you will discover a redesigned CERN Bulletin. Starting with the first May issue (No. 19-20/2006), the format of the Bulletin will change completely. The page layout will be more attractive, reminiscent of a proper newspaper, with pictograms to identify the different sections. The information provided will also be more visible. The Bulletin was much in need of a makeover as its current layout dates back to 1976! The introduction of the new format will coincide with the introduction of a new means of distribution. You will still receive the electronic version of the Bulletin every week directly on your computer. However, in order to avoid the waste from the dozens of copies that linger unread in people's mailboxes, the paper version will be available at a series of distribution points around the Laboratory. You will find the Bulletin along with the Staff Association newsletter at the cafeteria closest to your office. The Bulletin will be available from the following distribution points: On the Meyrin...

  4. Ergonomic Redesign of an Industrial Control Panel

    Directory of Open Access Journals (Sweden)

    S Raeisi

    2016-07-01

    Full Text Available Operator's role in industrial control centers takes place in time, which is one of the most important determinants of whether an expected action is going to be successful or not. In certain situations, due to the complex nature of the work, the existing interfaces and already prepared procedures do not meet the dynamic requirements of operator's cognitive demands, making the control tasks unnecessarily difficult. This study was conducted to identify ergonomic issues with a specific industrial control panel, and redesign its layout and elements to enhance its usability. Task and link analysis methodologies were implemented. All essential functions and supporting operations were identified at the required trivial levels. Next, the weight of any possible link between the elements of the panel was computed as a composite index of frequency and importance. Finally, all components were rearranged within a new layout, and a computerized mockup was generated. A total of 8 primary tasks was identified, including 4 system failure handling tasks, switching between manual and automated modes, and 3 types of routine vigilance and control tasks. These tasks were broken down into 28 functions and 145 supporting operations, accordingly. Higher link values were observed between hand rest position and 2 elements. Also, 6 other components showed robust linkages. In conclusion, computer modeling can reduce the likelihood of accidents and near misses in industrial control rooms by considering the operators' misperception or mental burden and correcting poor design of the panels and inappropriate task allocation.

  5. Case management redesign in an urban facility.

    Science.gov (United States)

    Almaden, Stefany; Freshman, Brenda; Quaye, Beverly

    2011-01-01

    To explore strategies for improving patient throughput and to redesign case management processes to facilitate level of care transitions and safe discharges. Large Urban Medical Center in South Los Angeles County, with 384 licensed beds that services poor, underserved communities. Both qualitative and quantitative methods were applied. Combined theoretical frameworks were used for needs assessment, intervention strategies, and change management. Observations, interviews, surveys, and database extraction methods were used. The sample consisted of case management staff members and several other staff from nursing, social work, and emergency department staff. Postintervention measures indicated improvement in reimbursements for services, reduction in length of stay, increased productivity, improved patients' access to care, and avoiding unnecessary readmission or emergency department visits. Effective change management strategies must consider multiple factors that influence daily operations and service delivery. Creating accountability by using performance measures associated with patient transitions is highlighted by the case study results. The authors developed a process model to assist in identifying and tracking outcome measures related to patient throughput, front-end assessments, and effective patient care transitions. This model can be used in future research to further investigate best case management practices.

  6. Redesign of the DFT/MRCI Hamiltonian

    Energy Technology Data Exchange (ETDEWEB)

    Lyskov, Igor; Kleinschmidt, Martin; Marian, Christel M., E-mail: Christel.Marian@hhu.de [Institute of Theoretical and Computational Chemistry, Heinrich-Heine-University Düsseldorf, Universitätsstraße 1, 40225 Düsseldorf (Germany)

    2016-01-21

    The combined density functional theory and multireference configuration interaction (DFT/MRCI) method of Grimme and Waletzke [J. Chem. Phys. 111, 5645 (1999)] is a well-established semi-empirical quantum chemical method for efficiently computing excited-state properties of organic molecules. As it turns out, the method fails to treat bi-chromophores owing to the strong dependence of the parameters on the excitation class. In this work, we present an alternative form of correcting the matrix elements of a MRCI Hamiltonian which is built from a Kohn-Sham set of orbitals. It is based on the idea of constructing individual energy shifts for each of the state functions of a configuration. The new parameterization is spin-invariant and incorporates less empirism compared to the original formulation. By utilizing damping techniques together with an algorithm of selecting important configurations for treating static electron correlation, the high computational efficiency has been preserved. The robustness of the original and redesigned Hamiltonians has been tested on experimentally known vertical excitation energies of organic molecules yielding similar statistics for the two parameterizations. Besides that, our new formulation is free from artificially low-lying doubly excited states, producing qualitatively correct and consistent results for excimers. The way of modifying matrix elements of the MRCI Hamiltonian presented here shall be considered as default choice when investigating photophysical processes of bi-chromophoric systems such as singlet fission or triplet-triplet upconversion.

  7. Redesigning Menstrual Education Programs Using Attitudes toward Menstruation.

    Science.gov (United States)

    Kieren, Dianne K.

    1992-01-01

    Critiques current menstrual education efforts and reviews current data about the nature of adolescent girls' attitudes toward menstruation as the basis for redesigning comprehensive, effective menstrual education programs. (Author)

  8. EVALUATION OF VALUE STREAM MAPPING IN MANUFACTURING SYSTEMS REDESIGNING

    OpenAIRE

    Serrano , Ibon; Ochoa Laburu , Carlos; De Castro , Rodolfo

    2008-01-01

    Abstract The Value Stream Mapping (VSM) technique, developed within the lean production paradigm, was presented as an innovative graphic technique to help practitioners redesign production systems. This paper presents the results of a project whose main purpose is to evaluate the real applicability of VSM to redesign disconnected flow lines based on manufacturing environments with a diversity of logistical problems. The research was developed using multiple case study methodology i...

  9. Methodology and findings of the NRC's materials licensing process redesign

    International Nuclear Information System (INIS)

    Rathbun, P.A.; Brown, K.D.; Madera, J.R.; Moriarty, M.; Pelchat, J.M.; Usilton, W.K.; Whitten, J.E.; Vacca, P.C.

    1996-04-01

    This report describes the work and vision of the team chartered to redesign the process for licensing users of nuclear materials. The Business Process Redesign team was chartered to improve the speed of the existing licensing process while maintaining or improving public safety and to achieve required resource levels. The report describes the team's methods for acquiring and analyzing information about the existing materials licensing process and the steps necessary to radically change this process to the envisioned future process

  10. Enzyme (re)design: lessons from natural evolution and computation.

    Science.gov (United States)

    Gerlt, John A; Babbitt, Patricia C

    2009-02-01

    The (re)design of enzymes to catalyze 'new' reactions is a topic of considerable practical and intellectual interest. Directed evolution (random mutagenesis followed by screening/selection) has been used widely to identify novel biocatalysts. However, 'rational' approaches using either natural divergent evolution or computational predictions based on chemical principles have been less successful. This review summarizes recent progress in evolution-based and computation-based (re)design.

  11. Application of Computer Simulation Modeling to Medication Administration Process Redesign

    OpenAIRE

    Huynh, Nathan; Snyder, Rita; Vidal, Jose M.; Tavakoli, Abbas S.; Cai, Bo

    2012-01-01

    The medication administration process (MAP) is one of the most high-risk processes in health care. MAP workflow redesign can precipitate both unanticipated and unintended consequences that can lead to new medication safety risks and workflow inefficiencies. Thus, it is necessary to have a tool to evaluate the impact of redesign approaches in advance of their clinical implementation. This paper discusses the development of an agent-based MAP computer simulation model that can be used to assess...

  12. Improvement of energy conversion efficiency and power generation in direct borohydride-hydrogen peroxide fuel cell: The effect of Ni-M core-shell nanoparticles (M = Pt, Pd, Ru)/Multiwalled Carbon Nanotubes on the cell performance

    Science.gov (United States)

    Hosseini, M. G.; Mahmoodi, R.

    2017-12-01

    In this study, core@shell nanoparticles with Ni as a core material and Pt, Pd and Ru as shell materials are synthesized on multiwalled carbon nanotube (MWCNT) as catalyst support using the sequence reduction method. The influence of Ni@Pt, Ni@Pd and Ni@Ru core@shell nanoparticles on MWCNT toward borohydride oxidation in alkaline solution is investigated by various three-electrode electrochemical techniques. Also, the impact of these anodic electrocatalysts on the performance of direct borohydride-hydrogen peroxide fuel cell (DBHPFC) is evaluated. The structural and morphological properties of electrocatalysts are studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HR-TEM) and X-ray photoelectron spectroscopy (XPS). The results of three electrode investigations show that Ni@Pd/MWCNT has excellent catalytic activity since borohydride oxidation current density on Ni@Pd/MWCNT (34773.27 A g-1) is 1.37 and 9.19 times higher than those of Ni@Pt/MWCNT (25347.27 A g-1) and Ni@Ru/MWCNT (3782.83 A g-1), respectively. Also, the energy conversion efficiency and power density of DBHPFC with Ni@Pd/MWCNT (246.82 mW cm-2) increase to 34.27% and 51.53% respect to Ni@Pt/MWCNT (162.24 mW cm-2) and Ni@Ru/MWCNT (119.62 mW cm-2), respectively. This study reveals that Ni@Pd/MWCNT has highest activity toward borohydride oxidation and stability in fuel cell.

  13. Advisory Committee on the Redesign of the Space Station

    Science.gov (United States)

    1993-06-01

    The Space Station Program was initiated in 1984 to provide for permanent human presence in an orbiting laboratory. This program evolved into Space Station Freedom, later identified as a component to facilitate a return of astronauts to the Moon, followed by the exploration of Mars. In March 1993 the Clinton Administration directed NASA to undertake an intense effort to redesign the space station at a substantial cost savings relative to Space Station Freedom. The Advisory Committee on the Redesign of the Space Station was established in March 1993 to provide independent assessment of the advantages and disadvantages of the redesign options. The results of the Committee's work is described. Discussion describes the mission that the Administration has articulated for the Space Station Program and the scientific and technical characteristics that a redesigned station must possess to fulfill those objectives. A description of recommended management, operations, and acquisition strategies for the redesigned program is provided. The Committee's assessment of the redesign options against five criteria are presented. The five criteria are technical capabilities, research capabilities, schedule, cost, and risk. A discussion of general mission risk is included.

  14. Developing an evaluation framework for clinical redesign programs: lessons learnt.

    Science.gov (United States)

    Samaranayake, Premaratne; Dadich, Ann; Fitzgerald, Anneke; Zeitz, Kathryn

    2016-09-19

    Purpose The purpose of this paper is to present lessons learnt through the development of an evaluation framework for a clinical redesign programme - the aim of which was to improve the patient journey through improved discharge practices within an Australian public hospital. Design/methodology/approach The development of the evaluation framework involved three stages - namely, the analysis of secondary data relating to the discharge planning pathway; the analysis of primary data including field-notes and interview transcripts on hospital processes; and the triangulation of these data sets to devise the framework. The evaluation framework ensured that resource use, process management, patient satisfaction, and staff well-being and productivity were each connected with measures, targets, and the aim of clinical redesign programme. Findings The application of business process management and a balanced scorecard enabled a different way of framing the evaluation, ensuring measurable outcomes were connected to inputs and outputs. Lessons learnt include: first, the importance of mixed-methods research to devise the framework and evaluate the redesigned processes; second, the need for appropriate tools and resources to adequately capture change across the different domains of the redesign programme; and third, the value of developing and applying an evaluative framework progressively. Research limitations/implications The evaluation framework is limited by its retrospective application to a clinical process redesign programme. Originality/value This research supports benchmarking with national and international practices in relation to best practice healthcare redesign processes. Additionally, it provides a theoretical contribution on evaluating health services improvement and redesign initiatives.

  15. Conversion program in Sweden

    Energy Technology Data Exchange (ETDEWEB)

    Jonsson, E.B. [Studsvik Nuclear AB, Nykoeping (Sweden)

    1997-08-01

    The conversion of the Swedish 50 MW R2 reactor from HEU to LEU fuel has been successfully accomplished over a 16 cycles long process. The conversion started in January 1991 with the introduction of 6 LEU assemblies in the 8*8 core. The first all LEU core was loaded in March 1993 and physics measurements were performed for the final licensing reports. A total of 142 LEU fuel assemblies have been irradiated up until September 1994 without any fuel incident. The operating licence for the R2 reactor was renewed in mid 1994 taking into account new fuel type. The Swedish Nuclear Inspectorate (SKI) pointed out one crucial problem with the LEU operation, that the back end of the LEU fuel cycle has not yet been solved. For the HEU fuel Sweden had the reprocessing alternative. The country is now relying heavily on the success of the USDOEs Off Site Fuels Policy to take back the spent fuel from the research reactors. They have in the meantime increased their intermediate storage facilities. There is, however, a limit both in time and space for storage of MTR-type of assemblies in water. The penalty of the lower thermal neutron flux in LEU cores has been reduced by improvements of the new irradiation rigs and by fine tuning the core calculations. The Studsvik code package, CASMO-SIMULATE, widely used for ICFM in LWRs has been modified to suit the compact MTR type of core.

  16. PSYCHOLOGICAL VALENCES IN THE DESIGN AND REDESIGN OF JOBS

    Directory of Open Access Journals (Sweden)

    Alic BIRCA

    2016-09-01

    Full Text Available This paper addresses the design and redesign of jobs under psychological aspect. For many years, the design and redesign of jobs have been treated more economically, i.e. by reducing staff costs. Although in the short-term, this approach has had positive economic effects, in the long-term the economic effects have been negative. Starting from this point of view, the authors attempt to highlight the problems that the psychological aspects involve in the design and redesign of jobs. Given the psychological aspects in the design of jobs aspects, are taken into consideration, certain problems that can have a far greater impact on organizational performance, may be anticipated and excluded.

  17. APPLICATION OF AUGMENTED REALITY IN FACADE REDESIGN PRESENTATION

    Directory of Open Access Journals (Sweden)

    PEJIĆ Petar

    2015-06-01

    Full Text Available Augmented Reality (AR is a computer technology where the perception of the user is enhanced by the seamless blending between real environment and computer-generated virtual objects coexisting in the same space. When it comes to a redesign of the existing facades, it is necessary to create a visual presentation of the proposed changes. For this reason, contemporary architectural approach assumes creating a digital 3D model of the newly designed facade. Since the façade redesign is a real world change, the AR can be used for newly designed facade project presentation. In this paper a case study of the AR application for façade redesign presentation of a single family house located in Babušnica (Serbia is presented.

  18. The Role of the IT Department in Organizational Redesign.

    Science.gov (United States)

    Petersen, Lone Stub

    2015-01-01

    Focus within eHealth research is often on development and implementation. However, the role of information systems maintenance and management is often neglected. In order for the IT department to accommodate the needs of the hospitals and continuous change of organization and practice there is a need for developing an understanding of the complex relationship between the IT department and clinical practice. In this paper the concept of redesign is used to deepen our understanding of IT related organizational change in healthcare organizations. In the paper I argue that the IT department is a central partner, steward and power in organizational change and learning in hospitals as the IT department serve both as a barrier and a catalyst of change and flexibility in the organization through management of information systems maintenance and redesign. Therefore it is important to consider and secure appropriate forms for stewarding redesign and learning in cooperation between the health care organizations and the IT department.

  19. Application of Computer Simulation Modeling to Medication Administration Process Redesign

    Directory of Open Access Journals (Sweden)

    Nathan Huynh

    2012-01-01

    Full Text Available The medication administration process (MAP is one of the most high-risk processes in health care. MAP workflow redesign can precipitate both unanticipated and unintended consequences that can lead to new medication safety risks and workflow inefficiencies. Thus, it is necessary to have a tool to evaluate the impact of redesign approaches in advance of their clinical implementation. This paper discusses the development of an agent-based MAP computer simulation model that can be used to assess the impact of MAP workflow redesign on MAP performance. The agent-based approach is adopted in order to capture Registered Nurse medication administration performance. The process of designing, developing, validating, and testing such a model is explained. Work is underway to collect MAP data in a hospital setting to provide more complex MAP observations to extend development of the model to better represent the complexity of MAP.

  20. Uranium conversion

    International Nuclear Information System (INIS)

    Oliver, Lena; Peterson, Jenny; Wilhelmsen, Katarina

    2006-03-01

    FOI, has performed a study on uranium conversion processes that are of importance in the production of different uranium compounds in the nuclear industry. The same conversion processes are of interest both when production of nuclear fuel and production of fissile material for nuclear weapons are considered. Countries that have nuclear weapons ambitions, with the intention to produce highly enriched uranium for weapons purposes, need some degree of uranium conversion capability depending on the uranium feed material available. This report describes the processes that are needed from uranium mining and milling to the different conversion processes for converting uranium ore concentrate to uranium hexafluoride. Uranium hexafluoride is the uranium compound used in most enrichment facilities. The processes needed to produce uranium dioxide for use in nuclear fuel and the processes needed to convert different uranium compounds to uranium metal - the form of uranium that is used in a nuclear weapon - are also presented. The production of uranium ore concentrate from uranium ore is included since uranium ore concentrate is the feed material required for a uranium conversion facility. Both the chemistry and principles or the different uranium conversion processes and the equipment needed in the processes are described. Since most of the equipment that is used in a uranium conversion facility is similar to that used in conventional chemical industry, it is difficult to determine if certain equipment is considered for uranium conversion or not. However, the chemical conversion processes where UF 6 and UF 4 are present require equipment that is made of corrosion resistant material

  1. Delivering Sustainability Through Supply Chain Distribution Network Redesign

    Directory of Open Access Journals (Sweden)

    Denise Ravet

    2013-09-01

    Full Text Available Purpose - Companies could gain (cost, service, green/sustainable competitive advantage through the supply chain network. The goal of this article is to study how to deliver sustainability through the supply chain distribution network redesign.Design/methodology/approach - A literature review is conducted to examine research relating to sustainable supply chain strategies and supply chain distribution network redesign.Findings - A study of the supply chain literature reveals the importance to rethink the supply chain distribution network design and to treat sustainability as integral to operations.

  2. Process efficiency. Redesigning social networks to improve surgery patient flow.

    Science.gov (United States)

    Samarth, Chandrika N; Gloor, Peter A

    2009-01-01

    We propose a novel approach to improve throughput of the surgery patient flow process of a Boston area teaching hospital. A social network analysis was conducted in an effort to demonstrate that process efficiency gains could be achieved through redesign of social network patterns at the workplace; in conjunction with redesign of organization structure and the implementation of workflow over an integrated information technology system. Key knowledge experts and coordinators in times of crisis were identified and a new communication structure more conducive to trust and knowledge sharing was suggested. The new communication structure is scalable without compromising on coordination required among key roles in the network for achieving efficiency gains.

  3. Conversation Analysis.

    Science.gov (United States)

    Schiffrin, Deborah

    1990-01-01

    Summarizes the current state of research in conversation analysis, referring primarily to six different perspectives that have developed from the philosophy, sociology, anthropology, and linguistics disciplines. These include pragmatics; speech act theory; interactional sociolinguistics; ethnomethodology; ethnography of communication; and…

  4. The creation of process redesigns by selecting, transforming and replacing process parts

    NARCIS (Netherlands)

    Netjes, M.; Reijers, H.A.; Aalst, van der W.M.P.

    2008-01-01

    For companies to sustain competitive advantages, it is required to redesign and improve business processes continuously by monitoring and analyzing process enactment results. Furthermore, organizational structures must be redesigned according to the changes in business processes. However, there are

  5. 77 FR 40358 - Federal Management Regulation; FMR Bulletin PBS-2012-03; Redesignations of Federal Buildings...

    Science.gov (United States)

    2012-07-09

    ... Management Regulation; FMR Bulletin PBS-2012-03; Redesignations of Federal Buildings: Correction AGENCY: Public Buildings Service (PBS), General Services Administration (GSA). ACTION: Notice of a bulletin..., 2012, a bulletin announcing the designation and redesignation of three Federal buildings. Inadvertently...

  6. Redesigning mental healthcare delivery : Is there an effect on organizational climate?

    NARCIS (Netherlands)

    Joosten, T.C.M.; Bongers, I.M.B.; Janssen, R.T.J.M.

    2014-01-01

    Objective Many studies have investigated the effect of redesign on operational performance; fewer studies have evaluated the effects on employees' perceptions of their working environment (organizational climate). Some authors state that redesign will lead to poorer organizational climate, while

  7. Multi-Stakeholder Collaboration in the Redesign of Family-Centered Rounds Process

    Science.gov (United States)

    Xie, Anping; Carayon, Pascale; Cartmill, Randi; Li, Yaqiong; Cox, Elizabeth D.; Plotkin, Julie A.; Kelly, Michelle M.

    2014-01-01

    A human factors approach to healthcare system redesign emphasizes the involvement of multiple healthcare stakeholders (e.g., patients and families, healthcare providers) in the redesign process. This study explores the experience of multiple stakeholders with collaboration in a healthcare system redesign project. Interviews were conducted with ten stakeholder representatives who participated in the redesign of the family-centered rounds process in a pediatric hospital. Qualitative interview data were analyzed using a phenomenological approach. A model of collaborative healthcare system redesign was developed, which defined four phases (i.e., setup of the redesign team, preparation for meetings, collaboration in meetings, follow-up after meetings) and two outcomes (i.e., team outcomes, redesign outcomes) of the collaborative process. Challenges to multi-stakeholder collaboration in healthcare system redesign, such as need to represent all relevant stakeholders, scheduling of meetings and managing different perspectives, were identified. PMID:25124394

  8. Redesigning Professional Development: Reconceptualising Teaching Using Social Learning Technologies

    Science.gov (United States)

    Cochrane, Thomas; Narayan, Vickel

    2013-01-01

    This article evaluates the use of a community of practice model for redesigning a lecturer professional development course investigating the impact of mobile web 2.0 technologies in higher education. The results show a significant change in lecturer conceptions of pedagogy were achieved by this approach. Drawing on our experience of two iterations…

  9. Structural analysis of 177-FA redesigned surveillance specimen holder tube

    International Nuclear Information System (INIS)

    Pryor, C.W.; Thoren, D.E.; Vames, G.J.; Harris, R.J.

    1976-08-01

    Because of in-service operational problems, the surveillance specimen holder tubes described in B and W topical report BAW-10051 have been redesigned. This report describes the new design and structural analysis for normal operation and upset loading conditions. The results of the analysis demonstrate the adequacy of the new surveillance specimen holder tubes for their design life of 40 years

  10. Evaluating treatment process redesign by applying the EFQM Excellence Model

    NARCIS (Netherlands)

    Nabitz, Udo; Schramade, Mark; Schippers, Gerard

    2006-01-01

    OBJECTIVE: To evaluate a treatment process redesign programme implementing evidence-based treatment as part of a total quality management in a Dutch addiction treatment centre. METHOD: Quality management was monitored over a period of more than 10 years in an addiction treatment centre with 550

  11. Redesigning School Accountability and Support: Progress in Pioneering States

    Science.gov (United States)

    Cook-Harvey, Channa M.; Stosich, Elizabeth Leisy

    2016-01-01

    How might policymakers and educators utilize the work already being done as states redesign their accountability systems? The 2015 reauthorization of the Elementary and Secondary Education Act (ESEA), brought much needed attention to the performance of traditionally underserved subgroups of students. Supported by greater flexibility under ESEA…

  12. A Lightweight Structure Redesign Method Based on Selective Laser Melting

    Directory of Open Access Journals (Sweden)

    Li Tang

    2016-11-01

    Full Text Available The purpose of this paper is to present a new design method of lightweight parts fabricated by selective laser melting (SLM based on the “Skin-Frame” and to explore the influence of fabrication defects on SLM parts with different sizes. Some standard lattice parts were designed according to the Chinese GB/T 1452-2005 standard and manufactured by SLM. Then these samples were tested in an MTS Insight 30 compression testing machine to study the trends of the yield process with different structure sizes. A set of standard cylinder samples were also designed according to the Chinese GB/T 228-2010 standard. These samples, which were made of iron-nickel alloy (IN718, were also processed by SLM, and then tested in the universal material testing machine INSTRON 1346 to obtain their tensile strength. Furthermore, a lightweight redesigned method was researched. Then some common parts such as a stopper and connecting plate were redesigned using this method. These redesigned parts were fabricated and some application tests have already been performed. The compression testing results show that when the minimum structure size is larger than 1.5 mm, the mechanical characteristics will hardly be affected by process defects. The cylinder parts were fractured by the universal material testing machine at about 1069.6 MPa. These redesigned parts worked well in application tests, with both the weight and fabrication time of these parts reduced more than 20%.

  13. Redesigning a Large Introductory Course to Incorporate the GAISE Guidelines

    Science.gov (United States)

    Woodard, Roger; McGowan, Herle

    2012-01-01

    In 2005, the "Guidelines for Assessment and Instruction in Statistics Education" (GAISE) college report described several recommendations for teaching introductory statistics. This paper discusses how a large multi-section introductory course was redesigned in order to implement these recommendations. The experience described discusses…

  14. Computational redesign of a mononuclear zinc metalloenzyme for organophosphate hydrolysis

    DEFF Research Database (Denmark)

    Khare, Sagar D.; Kipnis, Yakov; Greisen, Per Junior

    2012-01-01

    The ability to redesign enzymes to catalyze noncognate chemical transformations would have wide-ranging applications. We developed a computational method for repurposing the reactivity of metalloenzyme active site functional groups to catalyze new reactions. Using this method, we engineered a zinc...

  15. Redesign of a Life Span Development Course Using Fink's Taxonomy

    Science.gov (United States)

    Fallahi, Carolyn R.

    2008-01-01

    This study compared a traditional lecture-based life span development course to the same course redesigned using Fink's (2003) taxonomy of significant learning. The goals, activities, and feedback within the course corresponded to Fink's 6 taxa (knowledge, application, integration, human dimension, caring, learning how to learn). Undergraduates in…

  16. On Engineering Support for Business Process Modelling and Redesign

    NARCIS (Netherlands)

    Doumeingts, G.; Franken, H.M.; de Weger, M.K.; Browne, J.; Quartel, Dick; Ferreira Pires, Luis

    1997-01-01

    Currently, there is an enormous (research) interest in business process redesign (BPR). Several management-oriented approaches have been proposed showing how to make BPR work. However, detailed descriptions of empirical experience are few. Consistent engineering methodologies to aid and guide a

  17. Is State-Mandated Redesign an Effective and Sustainable Solution?

    Science.gov (United States)

    Young, Michelle D.

    2013-01-01

    There is a pervasive and ongoing perception that leadership preparation is a problem. Important questions remain about the intentions, capacity, and impact of state departments of education engaged in leadership preparation program redesign. In this essay, I take up several issues concerning this state policy work, including whether a one size…

  18. Usability Testing in a Library Web Site Redesign Project.

    Science.gov (United States)

    McMullen, Susan

    2001-01-01

    Discusses the need for an intuitive library information gateway to meet users' information needs and describes the process involved in redesigning a library Web site based on experiences at Roger Williams University. Explains usability testing methods that were used to discover how users were interacting with the Web site interface. (Author/LRW)

  19. Redesigning Schools to Raise Achievement. Item Number 39-0464

    Science.gov (United States)

    American Federation of Teachers, 2003

    2003-01-01

    The primary goal of the American Federation of Teachers' (AFT) Redesigning Schools to Raise Achievement (RSRA) project is to build capacity at the state, district, school, and classroom levels to improve student achievement to meet the goals of the 2001 No Child Left Behind Act. This checklist highlights some of the opportunities and support…

  20. Rethinking and Redesigning an Image Processing Course from a Problem-Based Learning Perspective

    DEFF Research Database (Denmark)

    Reng, Lars; Triantafyllou, Evangelia; Triantafyllidis, George

    2015-01-01

    of such concepts and being able to use them for solving real-world problems. The Problem-Based Learning (PBL) pedagogy is an approach, which favours learning by applying knowledge to solve such problems. However, formulating an appropriate project for image processing courses presents challenges on how......Our experience at the Media Technology department, Aalborg University Copenhangen has shown that learning core concepts and techniques in image processing is a challenge for undergraduate students. One possible cause for this is the gap between understanding the mathematical formalism...... to appropriately present relevant concepts and techniques to students. This article presents our redesign of an image processing course at the Media Technology department, which focused on relevant concept and technique presentation and design projects and employed a game engine (Unity) in order to present...

  1. 77 FR 35393 - Federal Management Regulation; FMR Bulletin PBS-2012-03; Redesignations of Federal Buildings

    Science.gov (United States)

    2012-06-13

    ... Management Regulation; FMR Bulletin PBS-2012-03; Redesignations of Federal Buildings AGENCY: Public Buildings... bulletin announces the designation and redesignation of three Federal buildings. Expiration Date: This bulletin announcement expires October 31, 2012. The building designation and redesignations remains in...

  2. 76 FR 54772 - Federal Management Regulation; FMR Bulletin PBS-2011-B2; Redesignations of Federal Buildings

    Science.gov (United States)

    2011-09-02

    ... Management Regulation; FMR Bulletin PBS-2011-B2; Redesignations of Federal Buildings AGENCY: Public Buildings... announces the designation and redesignation of two Federal buildings. Expiration Date: This bulletin announcement expires January 31, 2012. The building designation and redesignation remains in effect until...

  3. 75 FR 69080 - Federal Management Regulation; FMR Bulletin PBS-2010-B5; Redesignations of Federal Buildings

    Science.gov (United States)

    2010-11-10

    ... Management Regulation; FMR Bulletin PBS-2010-B5; Redesignations of Federal Buildings AGENCY: Public Buildings... announces the designation and redesignation of two Federal buildings. DATES: Expiration Date: This bulletin announcement expires April 30, 2011. The building designation and redesignation remains in effect until...

  4. 76 FR 6792 - Federal Management Regulation; FMR Bulletin PBS-2011-B1; Redesignations of Federal Buildings

    Science.gov (United States)

    2011-02-08

    ... Management Regulation; FMR Bulletin PBS-2011-B1; Redesignations of Federal Buildings AGENCY: Public Buildings... announces the redesignations of three Federal buildings. DATES: Expiration Date: This bulletin announcement expires June 30, 2011. The building redesignations remain in effect until canceled or superseded by...

  5. 75 FR 44264 - Federal Management Regulation; FMR Bulletin PBS-2010-B4; Redesignation of Federal Building

    Science.gov (United States)

    2010-07-28

    ... Management Regulation; FMR Bulletin PBS-2010-B4; Redesignation of Federal Building AGENCY: Public Buildings... announces the redesignation of a Federal building. DATES: Expiration Date: This bulletin expires December 31, 2010. However, the building redesignation announced by this bulletin will remain in effect until...

  6. 76 FR 59600 - Approval and Promulgation of Air Quality Implementation Plans; Indiana; Redesignation of Lake and...

    Science.gov (United States)

    2011-09-27

    ...] Approval and Promulgation of Air Quality Implementation Plans; Indiana; Redesignation of Lake and Porter... redesignation of the Lake and Porter Counties, Indiana portion (Lake and Porter Counties) of the Chicago-Gary... or standard). EPA is proposing to approve the redesignation request for Lake and Porter Counties...

  7. Business process redesign at a mental healthcare institute: a coulored petri net approach

    NARCIS (Netherlands)

    Jansen-Vullers, M.H.; Reijers, H.A.; Jensen, K.

    2005-01-01

    Business Process Redesign aims to radically improve the performance of business processes. One of the approaches to derive such an improved process design is an evolutionary approach, making use of redesign heuristics (Reijers, 2003). Simulation of the redesigned business process comes into play if

  8. Pictorial Conversations.

    Science.gov (United States)

    Hooper, Kristina

    1982-01-01

    Provides the rationale for considering communication in a graphic domain and suggests a specific goal for designing work stations which provide graphic capabilities in educational settings. The central element of this recommendation is the "pictorial conversation", a highly interactive exchange that includes pictures as the central elements.…

  9. Managing Conversations: The Medium for Achieving "Breakthrough" Results.

    Science.gov (United States)

    Bolton, Robert

    1998-01-01

    Unlike traditional management development, use of conversations in coaching high-performance work teams addresses core processes of speaking and listening. Management of conversations aims to create learning that will lead to breakthroughs in team performance. (SK)

  10. Development of high conversion boiling water reactor

    International Nuclear Information System (INIS)

    Yamashita, Jun-ichi; Mochida, Takaaki; Uchikawa, Sadao.

    1988-01-01

    It is expected that the period of LWRs being the main source of electric power supply becomes long, therefore, the development of next generation LWRs placing emphasis on the effective utilization of uranium resources and the improvement of economical efficiency is necessary. In this paper, as the next generation BWRs subsequent to ABWRs, the concept of the core of high conversion type BWRs is reported, in which emphasis is placed on the saving of natural uranium resources by raising the rate of conversion to plutonium. This core is that of realizing the high rate of conversion by utilizing the void in the core, which is the feature of BWRs, and the case of making the change of the core structure relatively small by using cross type control rods and the case of changing the core structure for further heightening the rate of conversion and making control rods into cluster type are described. In order to meet the demand like this, Hitachi Ltd. has engaged in the development of the concept of the core of next generation LWRs. In the high conversion type BWRs, there is not large change in the reactor system and turbine system from the current BWRs. The features and the concept of the core of high conversion type BWRs are described. (Kako, I.)

  11. A REDESIGN LAYOUT TO INCREASE PRODUCTIVITY OF A COMPANY

    Directory of Open Access Journals (Sweden)

    Vincentia Kitriastika

    2013-06-01

    Full Text Available This project is conducted in Company X, a passenger cars wheel producing company located in Sunter, North Jakarta. With a view of increasing the productivity of the company, the focus of this project will be redesigned the layout of the factory. The main problem encountered is that the goods are not produced in single location, causing a considerable hindrance in terms of time and distance, and hence efficiency. The redesigning layout process will use SLP method and flow analysis while supported by analysis of assembly line balancing to optimize the layout. Regarding the evaluation process, ARENA software will be used to simulate and identify the bottleneck in the production process, and comparing the layout alternatives to decide the best layout. The best chosen layout according to the simulation and SLP method that supported with flow analysis and assembly line balancing will be used as the master draft layout that will be proposed to Company X.

  12. Quantum conversion

    OpenAIRE

    Mazilu, Michael

    2015-01-01

    ICOAM 2015 The electromagnetic momentum transferred transferred to scattering particles is proportional to the intensity of the incident fields, however, the momentum of single photons ℏk does not naturally appear in these classical expressions. Here, we discuss an alternative to Maxwell's stress tensor that renders the classical electromagnetic field momentum compatible to the quantum mechanical one. This is achieved through the introduction of the quantum conversion which allows the tran...

  13. Conversational sensemaking

    Science.gov (United States)

    Preece, Alun; Webberley, Will; Braines, Dave

    2015-05-01

    Recent advances in natural language question-answering systems and context-aware mobile apps create opportunities for improved sensemaking in a tactical setting. Users equipped with mobile devices act as both sensors (able to acquire information) and effectors (able to act in situ), operating alone or in collectives. The currently- dominant technical approaches follow either a pull model (e.g. Apple's Siri or IBM's Watson which respond to users' natural language queries) or a push model (e.g. Google's Now which sends notifications to a user based on their context). There is growing recognition that users need more flexible styles of conversational interaction, where they are able to freely ask or tell, be asked or told, seek explanations and clarifications. Ideally such conversations should involve a mix of human and machine agents, able to collaborate in collective sensemaking activities with as few barriers as possible. Desirable capabilities include adding new knowledge, collaboratively building models, invoking specific services, and drawing inferences. As a step towards this goal, we collect evidence from a number of recent pilot studies including natural experiments (e.g. situation awareness in the context of organised protests) and synthetic experiments (e.g. human and machine agents collaborating in information seeking and spot reporting). We identify some principles and areas of future research for "conversational sensemaking".

  14. Conversational sensing

    Science.gov (United States)

    Preece, Alun; Gwilliams, Chris; Parizas, Christos; Pizzocaro, Diego; Bakdash, Jonathan Z.; Braines, Dave

    2014-05-01

    Recent developments in sensing technologies, mobile devices and context-aware user interfaces have made it pos- sible to represent information fusion and situational awareness for Intelligence, Surveillance and Reconnaissance (ISR) activities as a conversational process among actors at or near the tactical edges of a network. Motivated by use cases in the domain of Company Intelligence Support Team (CoIST) tasks, this paper presents an approach to information collection, fusion and sense-making based on the use of natural language (NL) and controlled nat- ural language (CNL) to support richer forms of human-machine interaction. The approach uses a conversational protocol to facilitate a ow of collaborative messages from NL to CNL and back again in support of interactions such as: turning eyewitness reports from human observers into actionable information (from both soldier and civilian sources); fusing information from humans and physical sensors (with associated quality metadata); and assisting human analysts to make the best use of available sensing assets in an area of interest (governed by man- agement and security policies). CNL is used as a common formal knowledge representation for both machine and human agents to support reasoning, semantic information fusion and generation of rationale for inferences, in ways that remain transparent to human users. Examples are provided of various alternative styles for user feedback, including NL, CNL and graphical feedback. A pilot experiment with human subjects shows that a prototype conversational agent is able to gather usable CNL information from untrained human subjects.

  15. Redesigning ambulatory care business processes supporting clinical care delivery.

    Science.gov (United States)

    Patterson, C; Sinkewich, M; Short, J; Callas, E

    1997-04-01

    The first step in redesigning the health care delivery process for ambulatory care begins with the patient and the business processes that support the patient. Patient-related business processes include patient access, service documentation, billing, follow-up, collection, and payment. Access is the portal to the clinical delivery and care management process. Service documentation, charge capture, and payment and collection are supporting processes to care delivery. Realigned provider networks now demand realigned patient business services to provide their members/customers/patients with improved service delivery at less cost. Purchaser mandates for cost containment, health maintenance, and enhanced quality of care have created an environment where every aspect of the delivery system, especially ambulatory care, is being judged. Business processes supporting the outpatient are therefore being reexamined for better efficiency and customer satisfaction. Many health care systems have made major investments in their ambulatory care environment, but have pursued traditional supporting business practices--such as multiple access points, lack of integrated patient appointment scheduling and registration, and multiple patient bills. These are areas that are appropriate for redesign efforts--all with the customer's needs and convenience in mind. Similarly, setting unrealistic expectations, underestimating the effort required, and ignoring the human elements of a patient-focused business service redesign effort can sabotage the very sound reasons for executing such an endeavor. Pitfalls can be avoided if a structured methodology, coupled with a change management process, are employed. Deloitte & Touche Consulting Group has been involved in several major efforts, all with ambulatory care settings to assist with the redesign of their business practices to consider the patient as the driver, instead of the institution providing the care.

  16. Acceptance of lean redesigns in primary care: A contextual analysis.

    Science.gov (United States)

    Hung, Dorothy; Gray, Caroline; Martinez, Meghan; Schmittdiel, Julie; Harrison, Michael I

    Lean is a leading change strategy used in health care to achieve short-term efficiency and quality improvement while promising longer-term system transformation. Most research examines Lean intervention to address isolated problems, rather than to achieve broader systemic changes to care delivery. Moreover, no studies examine contextual influences on system-wide Lean implementation efforts in primary care. The aim of this study was to identify contextual factors most critical to implementing and scaling Lean redesigns across all primary care clinics in a large, ambulatory care delivery system. Over 100 interviews and focus groups were conducted with frontline physicians, clinical staff, and operational leaders. Data analysis was guided by a modified Consolidated Framework for Implementation Research (CFIR), a popular implementation science framework. On the basis of expert recommendations, the modified framework targets factors influencing the implementation of process redesigns. This modified framework, the CFIR-PR, informed our identification of contextual factors that most impacted Lean acceptance among frontline physicians and staff. Several domains identified by the CFIR-PR were critical to acceptance of Lean redesigns. Regarding the implementation process acceptance was influenced by time and intensity of exposure to changes, "top-down" versus "bottom-up" implementation styles, and degrees of employee engagement in developing new workflows. Important factors in the inner setting were the clinic's culture and style of leadership, along with availability of information about Lean's effectiveness. Last, implementation efforts were impacted by individual and team characteristics regarding changed work roles and related issues of professional identity, authority, and autonomy. This study underscores the need for change leaders to consider the contextual factors that surround efforts to implement Lean in primary care. As Lean redesigns are scaled across a system

  17. Evaluating treatment process redesign by applying the EFQM Excellence Model.

    Science.gov (United States)

    Nabitz, Udo; Schramade, Mark; Schippers, Gerard

    2006-10-01

    To evaluate a treatment process redesign programme implementing evidence-based treatment as part of a total quality management in a Dutch addiction treatment centre. Quality management was monitored over a period of more than 10 years in an addiction treatment centre with 550 professionals. Changes are evaluated, comparing the scores on the nine criteria of the European Foundation for Quality Management (EFQM) Excellence Model before and after a major redesign of treatment processes and ISO certification. In the course of 10 years, most intake, care, and cure processes were reorganized, the support processes were restructured and ISO certified, 29 evidence-based treatment protocols were developed and implemented, and patient follow-up measuring was established to make clinical outcomes transparent. Comparing the situation before and after the changes shows that the client satisfaction scores are stable, that the evaluation by personnel and society is inconsistent, and that clinical, production, and financial outcomes are positive. The overall EFQM assessment by external assessors in 2004 shows much higher scores on the nine criteria than the assessment in 1994. Evidence-based treatment can successfully be implemented in addiction treatment centres through treatment process redesign as part of a total quality management strategy, but not all results are positive.

  18. Redesigning photosynthesis to sustainably meet global food and bioenergy demand

    Science.gov (United States)

    Ort, Donald R.; Merchant, Sabeeha S.; Alric, Jean; Barkan, Alice; Blankenship, Robert E.; Bock, Ralph; Croce, Roberta; Hanson, Maureen R.; Hibberd, Julian M.; Long, Stephen P.; Moore, Thomas A.; Moroney, James; Niyogi, Krishna K.; Parry, Martin A. J.; Peralta-Yahya, Pamela P.; Prince, Roger C.; Redding, Kevin E.; Spalding, Martin H.; van Wijk, Klaas J.; Vermaas, Wim F. J.; von Caemmerer, Susanne; Weber, Andreas P. M.; Yeates, Todd O.; Yuan, Joshua S.; Zhu, Xin Guang

    2015-01-01

    The world’s crop productivity is stagnating whereas population growth, rising affluence, and mandates for biofuels put increasing demands on agriculture. Meanwhile, demand for increasing cropland competes with equally crucial global sustainability and environmental protection needs. Addressing this looming agricultural crisis will be one of our greatest scientific challenges in the coming decades, and success will require substantial improvements at many levels. We assert that increasing the efficiency and productivity of photosynthesis in crop plants will be essential if this grand challenge is to be met. Here, we explore an array of prospective redesigns of plant systems at various scales, all aimed at increasing crop yields through improved photosynthetic efficiency and performance. Prospects range from straightforward alterations, already supported by preliminary evidence of feasibility, to substantial redesigns that are currently only conceptual, but that may be enabled by new developments in synthetic biology. Although some proposed redesigns are certain to face obstacles that will require alternate routes, the efforts should lead to new discoveries and technical advances with important impacts on the global problem of crop productivity and bioenergy production. PMID:26124102

  19. Training in Vocational Assessment: Preparing Rehabilitation Counselors and Meeting the Requirements of the CORE Standards

    Science.gov (United States)

    Tansey, Timothy N.

    2008-01-01

    Assessment represents a foundational component of rehabilitation counseling services. The revised Council on Rehabilitation Education (CORE) standards implemented in 2004 resulted in the redesign of the knowledge and outcomes under the Assessment standard. The author reviews the current CORE standard for training in assessment within the context…

  20. Proteomics Core

    Data.gov (United States)

    Federal Laboratory Consortium — Proteomics Core is the central resource for mass spectrometry based proteomics within the NHLBI. The Core staff help collaborators design proteomics experiments in a...

  1. The historical town core and traffic in Novo mesto

    Directory of Open Access Journals (Sweden)

    Lilijana Jankovič

    2001-01-01

    Full Text Available The historical town core of Novo mesto is subject to intolerable traffic conditions. Individual car use is suffocating the town core, but simultaneously good access is essential for shopkeepers and other inhabitants since buses don’t go there. The project proposes changes to the traffic regime, its basic goals are to redesign the town square into a pedestrian place and to eliminate transitory traffic by rerouting vehicles to less burdened side roads. It introduces short-term parking, smaller parking garages in the core and larger parking spaces on the edge and routes the buses through the town core.

  2. Developing engineering design core competences through analysis of industrial products

    DEFF Research Database (Denmark)

    Hansen, Claus Thorp; Lenau, Torben Anker

    2011-01-01

    Most product development work carried out in industrial practice is characterised by being incremental, i.e. the industrial company has had a product in production and on the market for some time, and now time has come to design a new and upgraded variant. This type of redesign project requires...... that the engineering designers have core design competences to carry through an analysis of the existing product encompassing both a user-oriented side and a technical side, as well as to synthesise solution proposals for the new and upgraded product. The authors of this paper see an educational challenge in staging...... a course module, in which students develop knowledge, understanding and skills, which will prepare them for being able to participate in and contribute to redesign projects in industrial practice. In the course module Product Analysis and Redesign that has run for 8 years we have developed and refined...

  3. Redesigning a clinical mentoring program for improved outcomes in the clinical training of clerks

    OpenAIRE

    Lin, Chia-Der; Lin, Blossom Yen-Ju; Lin, Cheng-Chieh; Lee, Cheng-Chun

    2015-01-01

    Introduction: Mentorship has been noted as critical to medical students adapting to clinical training in the medical workplace. A lack of infrastructure in a mentoring program might deter relationship building between mentors and mentees. This study assessed the effect of a redesigned clinical mentoring program from the perspective of clerks. The objective was to assess the benefits of the redesigned program and identify potential improvements.Methods: A redesigned clinical mentoring program ...

  4. The benefits of redesigning Benin's vaccine supply chain.

    Science.gov (United States)

    Brown, Shawn T; Schreiber, Benjamin; Cakouros, Brigid E; Wateska, Angela R; Dicko, Hamadou M; Connor, Diana L; Jaillard, Philippe; Mvundura, Mercy; Norman, Bryan A; Levin, Carol; Rajgopal, Jayant; Avella, Mélanie; Lebrun, Caroline; Claypool, Erin; Paul, Proma; Lee, Bruce Y

    2014-07-07

    New vaccine introductions have put strains on vaccine supply chains around the world. While increasing storage and transportation may be the most straightforward options, it is also important to consider what financial and operational benefits can be incurred. In 2012, suboptimal vaccine coverage and impending vaccine introductions prompted the Republic of Benin's Ministry of Health (MOH) to explore ways to improve their vaccine supply chain. Working alongside the Beninese MOH, we utilized our computational model, HERMES, to explore the impact on cost and vaccine availability of three possible options: (1) consolidating the Commune level to a Health Zone level, (2) removing the Commune level completely, and (3) removing the Commune level and expanding to 12 Department Stores. We also analyzed the impact of adding shipping loops during delivery. At baseline, new vaccine introductions without any changes to the current system increased the logistics cost per dose ($0.23 to $0.26) and dropped the vaccine availability to 71%. While implementing the Commune level removal scenario had the same capital costs as implementing the Health Zone scenario, the Health Zone scenario had lower operating costs. This increased to an overall cost savings of $504,255 when implementing shipping loops. The best redesign option proved to be the synergistic approach of converting to the Health Zone design and using shipping loops (serving ten Health Posts/loop). While a transition to either redesign or only adding shipping loops was beneficial, implementing a redesign option and shipping loops can yield both lower capital expenditures and operating costs. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

  5. Redesign av Escola forlag sine skoleordbøker

    OpenAIRE

    Heggen, Inger Helene

    2007-01-01

    Rapporten består av en litteraturstudie (med begrepsavklaringer og en gjennomgang av ordboktypografiens historie – med hovedvekt på engelsk ordboktypografi), en analyse av ettspråklige ordbøker i dag (både norske og engelske), og en analyse av Escola Forlags ordbøker (bokmål og nynorsk utgave). Til slutt – en demononstrasjon av min resulterende redesign av ordbøkene (omslag og innmat). Her har det vært særlig viktig å tydeliggjøre oppslagsordene og oppslagsordenes underelementer s...

  6. Redesign and modernization of radioactive waste administration systems in Ukraine

    Energy Technology Data Exchange (ETDEWEB)

    Nieder-Westermann, Gerald H.; Walther, Thorsten; Krone, Juergen [DBE Technology GmbH, Peine (Germany)

    2016-06-15

    The European Commission (EC) has undertaken a series of projects to render assistance to Ukraine in modernizing and redesigning the Ukrainian approach to the administration, management and ultimately disposal of all forms of radioactive waste, including waste associated with the Chornobyl accident as well as waste generated as part of the Ukrainian energy infrastructure and from industrial and medical applications. One of the most recently completed projects focused on modernizing Ukraine's management and administrative systems responsible for the disposal of radioactive waste.

  7. Redesign and modernization of radioactive waste administration systems in Ukraine

    International Nuclear Information System (INIS)

    Nieder-Westermann, Gerald H.; Walther, Thorsten; Krone, Juergen

    2016-01-01

    The European Commission (EC) has undertaken a series of projects to render assistance to Ukraine in modernizing and redesigning the Ukrainian approach to the administration, management and ultimately disposal of all forms of radioactive waste, including waste associated with the Chornobyl accident as well as waste generated as part of the Ukrainian energy infrastructure and from industrial and medical applications. One of the most recently completed projects focused on modernizing Ukraine's management and administrative systems responsible for the disposal of radioactive waste.

  8. Redesign of a supply network by considering stochastic demand

    Directory of Open Access Journals (Sweden)

    Juan Camilo Paz

    2015-09-01

    Full Text Available This paper presents the problem of redesigning a supply network of large scale by considering variability of the demand. The central problematic takes root in determining strategic decisions of closing and adjusting of capacity of some network echelons and the tactical decisions concerning to the distribution channels used for transporting products. We have formulated a deterministic Mixed Integer Linear Programming Model (MILP and a stochastic MILP model (SMILP whose objective functions are the maximization of the EBITDA (Earnings before Interest, Taxes, Depreciation and Amortization. The decisions of Network Design on stochastic model as capacities, number of warehouses in operation, material and product flows between echelons, are determined in a single stage by defining an objective function that penalizes unsatisfied demand and surplus of demand due to demand changes. The solution strategy adopted for the stochastic model is a scheme denominated as Sample Average Approximation (SAA. The model is based on the case of a Colombian company dedicated to production and marketing of foodstuffs and supplies for the bakery industry. The results show that the proposed methodology was a solid reference for decision support regarding to the supply networks redesign by considering the expected economic contribution of products and variability of the demand.

  9. Digital prototyping technique applied for redesigning plastic products

    Science.gov (United States)

    Pop, A.; Andrei, A.

    2015-11-01

    After products are on the market for some time, they often need to be redesigned to meet new market requirements. New products are generally derived from similar but outdated products. Redesigning a product is an important part of the production and development process. The purpose of this paper is to show that using modern technology, like Digital Prototyping in industry is an effective way to produce new products. This paper tries to demonstrate and highlight the effectiveness of the concept of Digital Prototyping, both to reduce the design time of a new product, but also the costs required for implementing this step. The results of this paper show that using Digital Prototyping techniques in designing a new product from an existing one available on the market mould offers a significantly manufacturing time and cost reduction. The ability to simulate and test a new product with modern CAD-CAM programs in all aspects of production (designing of the 3D model, simulation of the structural resistance, analysis of the injection process and beautification) offers a helpful tool for engineers. The whole process can be realised by one skilled engineer very fast and effective.

  10. Business Process Redesign Using EDI: the BHP steel experience

    Directory of Open Access Journals (Sweden)

    Paula Swatman

    1994-05-01

    Full Text Available EDI should not be seen as a competitive weapon - it does not offer a sustainable competitive advantage to its users as did the earlier inter-organisational systems (such as the various airline reservation systems. Instead EDI provides a standardised infrastructure upon which an adopting organisation can reengineer its business processes and thus confers a long-term, strategic and comparative advantage upon such an adopter. The potential for sustained competitive advantage to be derived from EDI arises from its integration with the organisational structure of its implementor, depending upon the implementing organisation's ability to redesign its business processes appropriately. This paper examines the case of (arguably the most sophisticated EDI-using company in Australia, BHP Steel, demonstrating the advantages obtainable by an organisation using EDI as a foundation for its reengineered organisational structure and business processes and concludes that: • there are real benefits to be obtained from an inter organisational electronic trading strategy founded on EDI as the enabling mechanism - benefits which are considerably more extensive than EDI's comparatively simple technical nature would appear to offer; • organisational gateways utilising an Application Generic approach to system integration and isolating the communications issue by insisting on the use of international data communications standards do offer a realistic and successful solution to the problem of internal and external trade for large and sophisticated organisations; • the majority of these achievements would have been either unlikely or totally impossible without BHP Steel's commitment to organisation-wide Business Process Redesign.

  11. BEPS redesign of 168 commercial buildings: summary report

    Energy Technology Data Exchange (ETDEWEB)

    Stoops, J.L.; Deringer, J.J.; Moreno, S.; Misuriello, H.P.

    1984-05-01

    The objective of this report is to present, in usable form, summary data from the Building Energy Performance Standards (BEPS) Phase II commercial buildings energy research conducted in 1978-1979. Summary data presented were obtained from two major research efforts: the BEPS Phase II Redesign experiment; and the related research on ASHRAE Standard 90-75R. The bulk of this report consists of data tabulations of key energy parameters for the 168 sample buildings, which were tabulated from computer-stored files of the 1978-1979 data. Two kinds of tabulations are included: numerical tabulations that extracted information from the computer-stored data base for the 168 sample buildings; and graphic presentations of the computer-generated data, plus data extracted from other sources. The intent is to provide a single data compendium of key energy-related factors from the 1978 redesign experiment and the associated 1978-1979 ASHRAE Standard 90-75R research. This report also supplements the information for which there was not space in the magazine articles. Thus, for some building types, additional analysis, comments, and data tabulations are included that could not be included in the articles because space was limited. These additional analysis items are not consistent across building types because both the energy conservation opportunities and the design strategies applied by the building designers varied considerably by building type. The chapters have been entered individually into EDB and ERA.

  12. Five Key Leadership Actions Needed to Redesign Family Medicine Residencies.

    Science.gov (United States)

    Kozakowski, Stanley M; Eiff, M Patrice; Green, Larry A; Pugno, Perry A; Waller, Elaine; Jones, Samuel M; Fetter, Gerald; Carney, Patricia A

    2015-06-01

    New skills are needed to properly prepare the next generation of physicians and health professionals to practice in medical homes. Transforming residency training to address these new skills requires strong leadership. We sought to increase the understanding of leadership skills useful in residency programs that plan to undertake meaningful change. The Preparing the Personal Physician for Practice (P4) project (2007-2014) was a comparative case study of 14 family medicine residencies that engaged in innovative training redesign, including altering the scope, content, sequence, length, and location of training to align resident education with requirements of the patient-centered medical home. In 2012, each P4 residency team submitted a final summary report of innovations implemented, overall insights, and dissemination activities during the study. Six investigators conducted independent narrative analyses of these reports. A consensus meeting held in September 2012 was used to identify key leadership actions associated with successful educational redesign. Five leadership actions were associated with successful implementation of innovations and residency transformation: (1) manage change; (2) develop financial acumen; (3) adapt best evidence educational strategies to the local environment; (4) create and sustain a vision that engages stakeholders; and (5) demonstrate courage and resilience. Residency programs are expected to change to better prepare their graduates for a changing delivery system. Insights about effective leadership skills can provide guidance for faculty to develop the skills needed to face practical realities while guiding transformation.

  13. Participatory ergonomics in redesigning a dyeing tub for fabric dyers.

    Science.gov (United States)

    Parimalam, P; Premalatha, M R; Padmini, D S; Ganguli, A K

    2012-01-01

    The 'saree' worn by women in India and many South Asian countries is dyed using a tub, usually in small scale units employing low capital and a small number of workers. While using these tubs, workers adopt awkward postures over long periods of time which results in severe discomfort in the neck, shoulders and lower extremities. The purpose of the study was to redesign the dyeing tub using a participatory approach and to study the impact of the newly designed tub on the reported body discomfort and rate of production. Redesigning of the dyeing tub was carried out using three parallel participative processes--(1) eliciting the views of workers who use the tub, (2) interacting with the proprietors of the small scale dyeing units (the employers) and the tub manufacturers, and (3) iterative prototype tub development based on inputs from the first two processes. These processes facilitated involvement of the stake-holders and the acceptance of change. The final prototype was tested by nine workers for a period of three months to evaluate the reduction in body discomfort and increase in rate of production (output). Studies on the impact of the new tub showed a reduction in discomfort level from 'severe' to 'moderate', and a mean increase of 7.9% in the output, confirming the benefits of the participative approach to ergonomics intervention. The involvement, trust and credibility generated by the participative process facilitated the acceptance of the final design.

  14. U.S. Domestic Reactor Conversion Programs

    International Nuclear Information System (INIS)

    Woolstenhulme, Eric

    2008-01-01

    The Conversion Projects Include: the revision of the facilities safety basis documents and supporting analysis, the fabrication of new LEU fuel, the change-out of the reactor core, and the removal of the used HEU fuel (by INL University Fuels Program or DOE-NE). The major entities involved are: the U.S. Nuclear Regulatory Commission, the University reactor department, the fuel and hardware fabricators, the Spent fuel receipt facilities, the Spent fuel shipping services, and the U.S. Department of Energy and their subcontractors. Three major Reactor Conversion Program milestones have been accomplished since 2006: the conversion of the TRIGA reactor at Texas A and M University Nuclear Science Center, the conversion of the University of Florida Training Reactor, and the conversion of the Purdue University Reactor. Four Reactor Conversion Program milestones yet to be accomplished in 2008 and 2009: the Washington State University Nuclear Radiation Center reactor, the Oregon State University TRIGA Reactor, the University of Wisconsin Nuclear Reactor, and the Neutron Radiography Reactor Facility. NNSA is committed to doing things cheaper, better, smarter, safer through a 'Lessons Learned' process. The conversion team assessed each major activity grouping: Project Initiation, Conversion Proposal Development, Fuel Fabrication and Hardware, Core Conversion, and Spent Nuclear Fuel Removal. Issues were identified and recommendations were given

  15. 77 FR 73575 - Approval and Promulgation of Air Quality Implementation Plans; West Virginia; Redesignation of...

    Science.gov (United States)

    2012-12-11

    ...) (supplemented at 57 FR 18070, April 28, 1992) and has provided further guidance on processing redesignation requests in the following documents: 1. ``Procedures for Processing Requests to Redesignate Areas to... interpolation between VISTAS/ASIP 2012 and 2018 modeling inventory. The 2022 EGU inventory for PM 2.5 , NO X...

  16. Learning to Redesign Teacher Education: A Conceptual Framework to Support Program Change

    Science.gov (United States)

    Anagnostopoulos, Dorothea; Levine, Thomas; Roselle, Rene; Lombardi, Allison

    2018-01-01

    University-based teacher education faces intensifying pressure to prove its effectiveness. This has prompted renewed interest in program redesign. In this article, we argue that enacting meaningful redesign requires university-based teacher educators to learn new ways of thinking and acting not only with teacher candidates but also with their…

  17. An evolutionary approach for business process redesign : towards an intelligent system

    NARCIS (Netherlands)

    Netjes, M.; Limam Mansar, S.; Reijers, H.A.; Aalst, van der W.M.P.; Cardoso, J.; Cordeiro, J.; Filipe, J.

    2007-01-01

    Although extensive literature on BPR is available, there is still a lack of concrete guidance on actually changing processes for the better. It is our goal to provide a redesign approach which describes and supports the steps to derive from an existing process a better performing redesign. In this

  18. Outsourcing of Corporate Information Services: Implications for Redesigning Corporate Library Services.

    Science.gov (United States)

    Agada, John

    1996-01-01

    Examines the trend in outsourcing information services and suggests it threatens the survival of corporate libraries. Topics include changes in the competitive corporate environment; characteristics of outsourceable services; managing change; redesigning the corporate librarian's role; and implications for redesigning corporate information…

  19. 76 FR 76302 - Approval and Promulgation of Air Quality Implementation Plans; Indiana; Redesignation of Lake and...

    Science.gov (United States)

    2011-12-07

    ...] Approval and Promulgation of Air Quality Implementation Plans; Indiana; Redesignation of Lake and Porter...). ACTION: Final rule. SUMMARY: EPA is taking several related actions affecting Lake and Porter Counties and... redesignation of Lake and Porter Counties to attainment of the 1997 annual PM 2.5 standard. EPA is approving, as...

  20. Redesigning Schools to Raise Achievement. Where We Stand. Item Number 39-0232

    Science.gov (United States)

    American Federation of Teachers, 2006

    2006-01-01

    This document contains resolution text adopted by the American Federation of Teachers (AFT) in July 1998 regarding Redesigning Low-Performing Schools. A Question & Answer section follows the resolution, addressing the following issues: (1) Union support for redesign or closure of low-performing schools; (2) Indicators of low-performing schools…

  1. Redesigning a Flexible Material Master Data Application with Language Dependency

    Directory of Open Access Journals (Sweden)

    Mihaela Muntean

    2016-06-01

    Full Text Available Based on some inconveniences identified within a material master data application of theSAP MM module, the current paper proposes an alternative technical solution for designing thepopup layout screen of the material master data application with respect to language dependency.The application should present the text of all tabs, areas and fields in the desired language based onthe user logon preferences. Also it has been implemented a possibility to sort the data in the desiredorder, so the customer isn’t forced, as before, to search for a certain field, when updating certainmaterials. The proposed solution suggests the use of five database tables, combined within threemaintenance views, which build a view cluster. The advantage of the redesigned application consistsof easier maintainability of the data (fields, areas and tabs can be easily added, deleted, reorderedand renamed and all the data within the view cluster can be translated into any language supportedby the system.

  2. Redesign of CERN LINAC3 RFQ for Lead 29+

    CERN Document Server

    Benedetti, Stefano; Lallement, Jean-Baptiste; Lombardi, Alessandra; CERN. Geneva. ATS Department

    2018-01-01

    CERN Linac3 is at the heart of the CERN Heavy Ion Facility, providing 4.2 MeV/u ion beams to the Low Energy Ion Ring (LEIR). It mostly accelerates 208Pb29+, though in recent years runs were performed with 40Ar11+ and 129Xe22+, in view of the raising interest of the physics community towards lighter ions experiments. In the framework of the LHC Injectors Upgrade (LIU) project, measurements and beam dynamics simulations showed that a transmission bottleneck of Linac3 is represented by the RFQ. As this accelerator was originally designed for 208Pb25+, the lower beam rigidity of the heavy ions currently in used – and planned to be used – permits a redesign of the RFQ aimed at increasing its transverse acceptance, and thus the transmitted beam current. The methodology adopted and the results of this study are presented.

  3. Key strategies and criteria to redesigning the nuclear fuel cycle

    International Nuclear Information System (INIS)

    Iakimets, V.N.

    1999-01-01

    Design of the nuclear fuel cycle (NFC) impacts future development of the nuclear industry on the one hand and the scale of the technological and environmental risk for future generations on the other hand. Adequate protection for humans and the biosphere will depend upon careful and unbiased design of the NFC. This paper addresses the two following problems: 1. What are the key strategies in restructuring nuclear power production itself in terms of choosing the safest possible variant of the NFC and identifying reasonable approaches to redesigning decision-making procedures for design, siting and operation, and decommissioning of new facilities, which have to be based on a strong legally approved citizen involvement. 2. What criteria should be used to evaluate any strategic or mid-term decisions related to the NFC, how can these be made operational, and what procedures may we apply to evaluate alternatives and select the most preferable one mutually acceptable to both citizens and nuclear specialists?

  4. A simulated annealing approach for redesigning a warehouse network problem

    Science.gov (United States)

    Khairuddin, Rozieana; Marlizawati Zainuddin, Zaitul; Jiun, Gan Jia

    2017-09-01

    Now a day, several companies consider downsizing their distribution networks in ways that involve consolidation or phase-out of some of their current warehousing facilities due to the increasing competition, mounting cost pressure and taking advantage on the economies of scale. Consequently, the changes on economic situation after a certain period of time require an adjustment on the network model in order to get the optimal cost under the current economic conditions. This paper aimed to develop a mixed-integer linear programming model for a two-echelon warehouse network redesign problem with capacitated plant and uncapacitated warehouses. The main contribution of this study is considering capacity constraint for existing warehouses. A Simulated Annealing algorithm is proposed to tackle with the proposed model. The numerical solution showed the model and method of solution proposed was practical.

  5. Implementing Business Process Redesign: early lessons from the Australian experience

    Directory of Open Access Journals (Sweden)

    Marianne Broadbent

    1995-05-01

    Full Text Available Business Process Redesign (BPR is a change management approach aimed at achieving quantum improvements in business performance. Industry interest levels in BPR are high as a direct result of current difficulties in the global economic climate and tight business conditions. Integral to BPR is the availability of new stable technologies which both stimulate and enable process changes. This paper highlights the experiences of a number of Australian firms which have implemented BPR. A ten step framework for BPR is presented together with a series of caveats. BPR is a difficult, messy and often non-linear activity which challenges many of the ways organisations operate. Information Technology plays a pivotal role in BPR as both an enabler and disenabler for change. Lessons emerging from early Australian experiences with BPR focus on the role of executive sponsorship, consultants, measurements, education and training, technology and people involved in the change process.

  6. Hubble Space Telescope EVA Power Ratchet Tool redesign

    Science.gov (United States)

    Richards, Paul W.; Park, Chan; Brown, Lee

    The Power Ratchet Tool (PRT) is a self contained, power-driven, 3/8 inch drive ratchet wrench which will be used by astronauts during Extravehicular Activities (EVA). This battery-powered tool is controlled by a dedicated electonic controller. The PRT was flown during the Hubble Space Telescope (HST) Deployment Mission STS-31 to deploy the solar arrays if the automatic mechanisms failed. The PRT is currently intended for use during the first HST Servicing Mission STS-61 as a general purpose power tool. The PRT consists of three major components; the wrench, the controller, and the battery module. Fourteen discrete combinations of torque, turns, and speed may be programmed into the controller before the EVA. The crewmember selects the desired parameter profile by a switch mounted on the controller. The tool may also be used in the manual mode as a non-powered ratchet wrench. The power is provided by a silver-zinc battery module, which fits into the controller and is replaceable during an EVA. The original PRT did not meet the design specification of torque output and hours of operation. To increase efficiency and reliability the PRT underwent a redesign effort. The majority of this effort focused on the wrench. The original PRT drive train consisted of a low torque, high speed brushless DC motor, a face gear set, and a planocentric gear assembly. The total gear reduction was 300:1. The new PRT wrench consists of a low speed, high torque brushless DC motor, two planetary gear sets and a bevel gear set. The total gear reduction is now 75:1. A spline clutch has also been added to disengage the drive train in the manual mode. The design changes to the controller will consist of only those modifications necessary to accomodate the redesigned wrench.

  7. Evaluation of In-Core Fuel Management for the Transition Cores of RSG-GAS Reactor to Full-Silicide Core

    International Nuclear Information System (INIS)

    S, Tukiran; MS, Tagor; P, Surian

    2003-01-01

    The core conversion of RSG-GAS reactor from oxide to silicide core with meat density of 2.96 gU/cc has been done. The core-of RSG-GAS reactor has been operated full core of silicide fuels which is started with the mixed core of oxide-silicide start from core 36. Based on previous work, the calculated core parameter for the cores were obtained and it is needed 9 transition cores (core 36 - 44) to achieve a full-silicide core (core 45). The objective of this work is to acquire the effect of the increment of the number of silicide fuel on the core parameters. Conversion core was achieved by transition cores mixed oxide-silicide fuels. Each transition core is calculated and measured core parameter such as, excess reactivity and shutdown margin. Calculation done by Batan-EQUIL-2D code and measurement of the core parameters was carried out using the method of compensation of couple control rods. The results of calculation and experiment shows that the excess reactivity trends lower with the increment of the number of silicide fuel in the core. However, the shutdown margin is not change with the increment of the number of silicide fuel. Therefore, the transition cores can be operated safely to a full-silicide core

  8. Heterogeneous gas core reactor

    International Nuclear Information System (INIS)

    Han, K.I.

    1977-01-01

    Preliminary investigations of a heterogeneous gas core reactor (HGCR) concept suggest that this potential power reactor offers distinct advantages over other existing or conceptual reactor power plants. One of the most favorable features of the HGCR is the flexibility of the power producing system which allows it to be efficiently designed to conform to a desired optimum condition without major conceptual changes. The arrangement of bundles of moderator/coolant channels in a fissionable gas or mixture of gases makes a truly heterogeneous nuclear reactor core. It is this full heterogeneity for a gas-fueled reactor core which accounts for the novelty of the heterogeneous gas core reactor concept and leads to noted significant advantages over previous gas core systems with respect to neutron and fuel economy, power density, and heat transfer characteristics. The purpose of this work is to provide an insight into the design, operating characteristics, and safety of a heterogeneous gas core reactor system. The studies consist mainly of neutronic, energetic and kinetic analyses of the power producing and conversion systems as a preliminary assessment of the heterogeneous gas core reactor concept and basic design. The results of the conducted research indicate a high potential for the heterogeneous gas core reactor system as an electrical power generating unit (either large or small), with an overall efficiency as high as 40 to 45%. The HGCR system is found to be stable and safe, under the conditions imposed upon the analyses conducted in this work, due to the inherent safety of ann expanding gaseous fuel and the intrinsic feedback effects of the gas and water coolant

  9. Redesigning mental healthcare delivery: is there an effect on organizational climate?

    Science.gov (United States)

    Joosten, T C M; Bongers, I M B; Janssen, R T J M

    2014-02-01

    Many studies have investigated the effect of redesign on operational performance; fewer studies have evaluated the effects on employees' perceptions of their working environment (organizational climate). Some authors state that redesign will lead to poorer organizational climate, while others state the opposite. The goal of this study was to empirically investigate this relation. Organizational climate was measured in a field experiment, before and after a redesign intervention. At one of the sites, a redesign project was conducted. At the other site, no redesign efforts took place. Two Dutch child- and adolescent-mental healthcare providers. Professionals that worked at one of the units at the start and/or the end of the intervention period. The main intervention was a redesign project aimed at improving timely delivery of services (modeled after the breakthrough series). Scores on the four models of the organizational climate measure, a validated questionnaire that measures organizational climate. Our analysis showed that climate at the intervention site changed on factors related to productivity and goal achievement (rational goal model). The intervention group scored worse than the comparison group on the part of the questionnaire that focuses on sociotechnical elements of organizational climate. However, observed differences were so small, that their practical relevance seems rather limited. Redesign efforts in healthcare, so it seems, do not influence organizational climate as much as expected.

  10. Transformer core

    NARCIS (Netherlands)

    Mehendale, A.; Hagedoorn, Wouter; Lötters, Joost Conrad

    2008-01-01

    A transformer core includes a stack of a plurality of planar core plates of a magnetically permeable material, which plates each consist of a first and a second sub-part that together enclose at least one opening. The sub-parts can be fitted together via contact faces that are located on either side

  11. Transformer core

    NARCIS (Netherlands)

    Mehendale, A.; Hagedoorn, Wouter; Lötters, Joost Conrad

    2010-01-01

    A transformer core includes a stack of a plurality of planar core plates of a magnetically permeable material, which plates each consist of a first and a second sub-part that together enclose at least one opening. The sub-parts can be fitted together via contact faces that are located on either side

  12. International Space Station (ISS) Potable Water Dispenser (PWD) Beverage Adapter (BA) Redesign

    Science.gov (United States)

    Edgerly, Rachel; Benoit, Jace; Shindo, David

    2012-01-01

    The Potable Water Dispenser used on the International Space Station (ISS) interfaces with food and drink packages using the Beverage Adapter and Needle. Unexpected leakage has been seen in this interface. The Beverage Adapter used on ]orbit was returned to the ground for Test, Teardown, and Evaluation. The results of that investigation prompted a redesign of the Beverage Adapter and Needle. The Beverage Adapter materials were changed to be more corrosion resistant, and the Needle was redesigned to preclude leakage. The redesigns have been tested and proven.

  13. Microturbine Power Conversion Technology Review

    Energy Technology Data Exchange (ETDEWEB)

    Staunton, R.H.

    2003-07-21

    In this study, the Oak Ridge National Laboratory (ORNL) is performing a technology review to assess the market for commercially available power electronic converters that can be used to connect microturbines to either the electric grid or local loads. The intent of the review is to facilitate an assessment of the present status of marketed power conversion technology to determine how versatile the designs are for potentially providing different services to the grid based on changes in market direction, new industry standards, and the critical needs of the local service provider. The project includes data gathering efforts and documentation of the state-of-the-art design approaches that are being used by microturbine manufacturers in their power conversion electronics development and refinement. This project task entails a review of power converters used in microturbines sized between 20 kW and 1 MW. The power converters permit microturbine generators, with their non-synchronous, high frequency output, to interface with the grid or local loads. The power converters produce 50- to 60-Hz power that can be used for local loads or, using interface electronics, synchronized for connection to the local feeder and/or microgrid. The power electronics enable operation in a stand-alone mode as a voltage source or in grid-connect mode as a current source. Some microturbines are designed to automatically switch between the two modes. The information obtained in this data gathering effort will provide a basis for determining how close the microturbine industry is to providing services such as voltage regulation, combined control of both voltage and current, fast/seamless mode transfers, enhanced reliability, reduced cost converters, reactive power supply, power quality, and other ancillary services. Some power quality improvements will require the addition of storage devices; therefore, the task should also determine what must be done to enable the power conversion circuits to

  14. Core lifter

    Energy Technology Data Exchange (ETDEWEB)

    Pavlov, N G; Edel' man, Ya A

    1981-02-15

    A core lifter is suggested which contains a housing, core-clamping elements installed in the housing depressions in the form of semirings with projections on the outer surface restricting the rotation of the semirings in the housing depressions. In order to improve the strength and reliability of the core lifter, the semirings have a variable transverse section formed from the outside by the surface of the rotation body of the inner arc of the semiring aroung the rotation axis and from the inner a cylindrical surface which is concentric to the outer arc of the semiring. The core-clamping elements made in this manner have the possibility of freely rotating in the housing depressions under their own weight and from contact with the core sample. These semirings do not have weakened sections, have sufficient strength, are inserted into the limited ring section of the housing of the core lifter without reduction in its through opening and this improve the reliability of the core lifter in operation.

  15. Redesigned front end for the upgrade at CHESS

    International Nuclear Information System (INIS)

    Headrick, R.L.; Smolenski, K.W.

    1996-01-01

    We will report on beamline front-end upgrades for the 24-pole wiggler beamlines at CHESS. A new design for primary x-ray beamstops based on a tapered, water-cooled copper block has been implemented and installed in the CHESS F beamline. The design uses a horizontally tapered open-quote open-quote V close-quote close-quote shape to reduce the power density on the internal surfaces and internal water channels in the block to provide efficient water cooling. Upstream of the beam stops, we have installed a new photoelectron style beam position monitor with separate monitoring of the wiggler and dipole vertical beam positions and with micron-level sensitivity. The monitor close-quote s internal surfaces are designed to absorb the full x-ray power in case of beam missteering, and the uncooled photoelectron collecting plates are not visible to the x-ray beam. A graphite prefilter has been installed to protect the beryllium windows that separate the front end from the x-ray optics downstream. The redesigned front end is required by the upgrade of the Cornell storage ring, now in progress, which will allow stored electron and positron currents of 300 mA by 1996, and 500 mA by 1998. At 500 mA, the wiggler power output will be over 32 kW. copyright 1996 American Institute of Physics

  16. REDESIGN OF CERNS QUADRUPOLE RESONATOR FOR TESTING OF SUPERCONDUCTING SAMPLES

    CERN Document Server

    Del Pozo Romano, Veronica

    2017-01-01

    The quadrupole resonator (QPR) was constructed in 1997 to measure the surface resistance of niobium samples at 400 MHz, the technology and RF frequency chosen for the LHC. It allows measurement of the RF properties of superconducting films deposited on disk-shaped metallic substrates. The samples are used to study different coatings which is much faster than the coating, stripping and re-coating of sample cavities. An electromagnetic and mechanical re-design of the existing QPR has been done with the goal of doubling the magnetic peak fields on the samples. Electromagnetic simulations were carried out on a completely parametrized model, using the existings QPR as baseline and modifying its dimensions. The aim was to optimize the measurement range and resolution by increasing the ratio between the magnetic peak fields on the sample and in the cavity. Increasing the average magnetic field on the sample leads to a more homogenous field distribution over the sample. Some of the modifications were based on t...

  17. Job crafting: Towards a new model of individual job redesign

    Directory of Open Access Journals (Sweden)

    Maria Tims

    2010-12-01

    Research purpose: The purpose of the study was to fit job crafting in job design theory. Motivation for the study: The study was an attempt to shed more light on the types of proactive behaviours of individual employees at work. Moreover, we explored the concept of job crafting and its antecedents and consequences. Research design, approach and method: A literature study was conducted in which the focus was first on proactive behaviour of the employee and then on job crafting. Main findings: Job crafting can be seen as a specific form of proactive behaviour in which the employee initiates changes in the level of job demands and job resources. Job crafting may be facilitated by job and individual characteristics and may enable employees to fit their jobs to their personal knowledge, skills and abilities on the one hand and to their preferences and needs on the other hand. Practical/managerial implications: Job crafting may be a good way for employees to improve their work motivation and other positive work outcomes. Employees could be encouraged to exert more influence on their job characteristics. Contribution/value-add: This article describes a relatively new perspective on active job redesign by the individual, called job crafting, which has important implications for job design theories.

  18. Redesigning assembly stations using ergonomic methods as a lean tool.

    Science.gov (United States)

    Eswaramoorthi, M; John, Mervyn; Rajagopal, C Arjun; Prasad, P S S; Mohanram, P V

    2010-01-01

    With the current state of the global economy, demand for various products plummeting. To sustain in the market, companies have to reduce cost and improve quality. Today, companies have started implementing new philosophies like TQM, TPM, six sigma and lean manufacturing techniques to remain competitive in the market. Lean manufacturing is an emerging philosophy which continuously strives to reduce waste. The main objective of analyzing the assembly line with a lean perspective is to identify the areas related to human interface with other systems that could lead to the generation of waste. Improper workplace design leads to unreasonable mental or physical burden and results in waste generation like slow work (delay and inventory), and defects, which is named as muri waste. An attempt has been made in this paper to locate muri waste and create a "Lean assembly line". The proposed method, based on the use of Rapid Upper Limb Assessment (RULA) with CATIA V5 platform, has allowed the measurement of a large set of operator posture parameters and assessment of ergonomic stresses. Based on the results, the process stations in the assembly line were redesigned to prevent the generation of waste.

  19. Re-designing the PhEDEx security model

    CERN Document Server

    Wildish, Anthony

    2013-01-01

    PhEDEx. the data-placement tool used by the CMS experiment at the LHC, was conceived in a more trusting time. The security model was designed to provide a safe working environment for site agents and operators, but provided little more protection than that. CMS data was not sufficiently protected against accidental loss caused by operator error or software bugs or from loss of data caused by deliberate manipulation of the database. Operations staff were given high levels of access to the database, beyond what should have been needed to accomplish their tasks. This exposed them to the risk of suspicion should an incident occur. Multiple implementations of the security model led to difficulties maintaining code, which can lead to degredation of security over time.In order to meet the simultaneous goals of protecting CMS data, protecting the operators from undue exposure to risk, increasing monitoring capabilities and improving maintainability of the security model, the PhEDEx security model was redesigned and r...

  20. Rational redesign of the biodegradative enzyme cytochrome P450 cam:

    International Nuclear Information System (INIS)

    Ornstein, R.; Paulsen, M.; Bass, M.; Arnold, G.

    1991-03-01

    Cytochromes P450, a superfamily of monooxygenase enzymes present in all kingdoms of living organisms, are very versatile with respect to substrate range and catalytic functionality. Many recalcitrant halogenated hydrocarbons, on DOE sites and throughout the nation, result in serious environmental impact. Cytochromes P450 have been shown to be catalytically capable of, at least partial, dehalogenation of some such compounds. Clearly, however, their active site stereochemistry and related functional components are not well suited for this role because the rates of dehalogenation are generally rather modest. The evolution of modified active site and access channel structures may proceed very slowly if multiple genetic changes are simultaneously required for enzyme adaptation. Since each mutational event is by itself a rare event, a basic premise of our research is that designing multiple changes into an enzyme may be more timely than waiting for them to occur biologically either via natural selection or under laboratory-controlled conditions. Starting with available high-resolution x-ray crystal structures, molecular modeling and molecular dynamics simulations have been used to probe the basic structure/function principles and conformational fluctuations of the biodegradative enzyme, cytochrome P450cam (camphor hydroxylase from Pseudomonas putida) and active site mutants, to provide the fundamental understanding necessary for rational engineering of the enzyme for modified substrate specificity. In the present paper, we review our progress to data, in the area of molecular dynamics simulations and active site redesign of P450cam. 36 refs., 2 figs

  1. Bus network redesign for inner southeast suburbs of Melbourne, Australia

    Science.gov (United States)

    Pandangwati, S. T.; Milyanab, N. A.

    2017-06-01

    Public transport is the most effective mode of transport in the era of climate change and oil depletion. It can address climate change issues by reducing urban greenhouse gas emission and oil consumption while at the same time improving mobility. However, many public transport networks are not effective and instead create high operating costs with low frequencies and occupancy. Melbourne is one example of a metropolitan area that faces this problem. Even though the city has well-integrated train and tram networks, Melbourne’s bus network still needs to be improved. This study used network planning approach to redesign the bus network in the City of Glen Eira, a Local Government Area (LGA) in the southeastern part of Metropolitan Melbourne. The study area is the area between Gardenvale North and Oakleigh Station, as well as between Caulfield and Patterson Stations. This area needs network improvement mainly because of the meandering bus routes that run within it. This study aims to provide recommendations for improving the performance of bus services by reducing meandering routes, improving transfer point design and implementing coordinated timetables. The recommendations were formulated based on a ‘ready-made’ concept to increase bus occupancy. This approach can be implemented in other cities with similar problems and characteristics including those in Indonesia.

  2. Redesigning NASA Earthdata to Become Powered by EOSDIS Components

    Science.gov (United States)

    Bagwell, R.; Siarto, J.; Wong, M. M.; Murphy, K. J.; McLaughlin, B. D.

    2014-12-01

    Two years ago, NASA's Earth Science Data and Information Systems (ESDIS) Project launched the Earthdata website (https://earthdata.nasa.gov) in order to make Earth Observing System Data and Information System (EOSDIS) data, data products, data tools, and services available to a broad range of user communities across Earth science disciplines to foster collaboration and learning amongst the communities. Earthdata is being redesigned to be the one-stop shop in providing Earth science data, services, and information to the Earth science community. The goal is to move from the current static, manually-intensive content format to a dynamic, data-driven website in order to provide a more flexible and usable design website infrastructure that leverages EOSDIS components such as the User Registration System (URS), the Common Metadata Repository (CMR) and the Global Imagery Browse Services (GIBS). This will reorganize information content to make the website easier to use and to make easily accessible the high-value Earth science content throughout the site. The website will also easily accept and incorporate upcoming new projects such as the Earthdata Search Client and the Sea Level Change Portal.

  3. Re-designing the PhEDEx Security Model

    Science.gov (United States)

    C-H, Huang; Wildish, T.; X, Zhang

    2014-06-01

    PhEDEx, the data-placement tool used by the CMS experiment at the LHC, was conceived in a more trusting time. The security model provided a safe environment for site agents and operators, but offerred little more protection than that. Data was not sufficiently protected against loss caused by operator error or software bugs or by deliberate manipulation of the database. Operators were given high levels of access to the database, beyond what was actually needed to accomplish their tasks. This exposed them to the risk of suspicion should an incident occur. Multiple implementations of the security model led to difficulties maintaining code, which can lead to degredation of security over time. In order to meet the simultaneous goals of protecting CMS data, protecting the operators from undue exposure to risk, increasing monitoring capabilities and improving maintainability of the security model, the PhEDEx security model was redesigned and re-implemented. Security was moved from the application layer into the database itself, fine-grained access roles were established, and tools and procedures created to control the evolution of the security model over time. In this paper we describe this work, we describe the deployment of the new security model, and we show how these enhancements improve security on several fronts simultaneously.

  4. Redesigning nursing work in long-term care environments.

    Science.gov (United States)

    Hall, L M; O'Brien-Pallas, L

    2000-01-01

    The authors present a highly statistically oriented argument for examining work attitudes and activities among three groups of caregivers [RNs, RPNs, and HCAs] working in long-term care. The investigators used both work sampling, written surveys, and interviews with a sample of 46 caregivers in a large university-affiliated LTC facility in Toronto, Canada. While RNs stated their strong affinity for direct patient care activities, they perform the lowest percentage of direct care, chiefly due to their accountability for planning and coordinating the care provided by others. The HCAs who provided the bulk of direct patient care "valued it the least," apparently finding little gratification with this aspect of their role. This study suggests that there is a need to examine and clarify work roles and perceptions for all caregivers as part of any work redesign process. A higher level of RN involvement in direct patient care activities, along with "attention to enhancing the importance" of these activities for staff employed in the HCA role, could be beneficial.

  5. Redesigning Health Care Practices to Address Childhood Poverty.

    Science.gov (United States)

    Fierman, Arthur H; Beck, Andrew F; Chung, Esther K; Tschudy, Megan M; Coker, Tumaini R; Mistry, Kamila B; Siegel, Benjamin; Chamberlain, Lisa J; Conroy, Kathleen; Federico, Steven G; Flanagan, Patricia J; Garg, Arvin; Gitterman, Benjamin A; Grace, Aimee M; Gross, Rachel S; Hole, Michael K; Klass, Perri; Kraft, Colleen; Kuo, Alice; Lewis, Gena; Lobach, Katherine S; Long, Dayna; Ma, Christine T; Messito, Mary; Navsaria, Dipesh; Northrip, Kimberley R; Osman, Cynthia; Sadof, Matthew D; Schickedanz, Adam B; Cox, Joanne

    2016-04-01

    Child poverty in the United States is widespread and has serious negative effects on the health and well-being of children throughout their life course. Child health providers are considering ways to redesign their practices in order to mitigate the negative effects of poverty on children and support the efforts of families to lift themselves out of poverty. To do so, practices need to adopt effective methods to identify poverty-related social determinants of health and provide effective interventions to address them. Identification of needs can be accomplished with a variety of established screening tools. Interventions may include resource directories, best maintained in collaboration with local/regional public health, community, and/or professional organizations; programs embedded in the practice (eg, Reach Out and Read, Healthy Steps for Young Children, Medical-Legal Partnership, Health Leads); and collaboration with home visiting programs. Changes to health care financing are needed to support the delivery of these enhanced services, and active advocacy by child health providers continues to be important in effecting change. We highlight the ongoing work of the Health Care Delivery Subcommittee of the Academic Pediatric Association Task Force on Child Poverty in defining the ways in which child health care practice can be adapted to improve the approach to addressing child poverty. Copyright © 2016 Academic Pediatric Association. All rights reserved.

  6. New Trends for Re-design the IT Companies

    Directory of Open Access Journals (Sweden)

    Florin Ionita

    2008-07-01

    Full Text Available As it is known, the management adaptability to the changes taking place in the environment where it is acting represents a key factor for survival and development of an organization. As a reaction to the external signals, the internal change may be superficial when it affects only the development of activity in different sectors, or might be profound, when it changes the main processes and rules of the business and even the philosophy of the company’s existence. Speaking about structural changes, one of the most common approaches of the modern management is the re-design of the business architecture. The new architectural models such as Service Oriented Architecture (SOA, presented in this paper, come with important advantages, but their implementation is not always very easy. This paper tries to present some of the most common encountered contextual characteristics which are able to start the implementation of Service Oriented Architecture, some advantages of this concept as well as some practical approaches of implementing.

  7. Redesigning a collection system for 'small' consumer electronics

    International Nuclear Information System (INIS)

    Melissen, Frans W.

    2006-01-01

    This paper establishes that the collection system within the recycling scheme for consumer electronics in the Netherlands has not been entirely successful in convincing consumers to hand in their used appliances by means of dedicated collection routes. Particularly regarding small appliances, consumers are persisting in their habit of discarding their appliances by means of the refuse bag/bin for regular household waste. Therefore, the current collection system has been unable to direct consumer behavior in the desired direction. Consequently, the layout of the current system is reviewed and redesigned in order to tackle this problem. This design effort applies the Triad model (behavioral model) in the analysis stage and the Morphological Chart method (design tool) in the synthesis stage, and results in a concrete proposal for a new system. Finally, the applicability of this design approach beyond the specific circumstances of the case study presented in this paper is discussed. This case represents only one example of the broader, worldwide challenge to design appropriate collection systems to direct consumer behavior in desired directions. It is argued that the approach presented in this paper could be a valuable contribution to research dealing with this challenge

  8. Re-designing the PhEDEx security model

    International Nuclear Information System (INIS)

    Huang C-H; Wildish, T; Zhang X

    2014-01-01

    PhEDEx, the data-placement tool used by the CMS experiment at the LHC, was conceived in a more trusting time. The security model provided a safe environment for site agents and operators, but offerred little more protection than that. Data was not sufficiently protected against loss caused by operator error or software bugs or by deliberate manipulation of the database. Operators were given high levels of access to the database, beyond what was actually needed to accomplish their tasks. This exposed them to the risk of suspicion should an incident occur. Multiple implementations of the security model led to difficulties maintaining code, which can lead to degredation of security over time. In order to meet the simultaneous goals of protecting CMS data, protecting the operators from undue exposure to risk, increasing monitoring capabilities and improving maintainability of the security model, the PhEDEx security model was redesigned and re-implemented. Security was moved from the application layer into the database itself, fine-grained access roles were established, and tools and procedures created to control the evolution of the security model over time. In this paper we describe this work, we describe the deployment of the new security model, and we show how these enhancements improve security on several fronts simultaneously.

  9. Cupryphans, metal-binding, redox-active, redesigned conopeptides.

    Science.gov (United States)

    Barba, Marco; Sobolev, Anatoli P; Romeo, Cristina; Schininà, M Eugenia; Pietraforte, Donatella; Mannina, Luisa; Musci, Giovanni; Polticelli, Fabio

    2009-03-01

    Contryphans are bioactive peptides, isolated from the venom of marine snails of the genus Conus, which are characterized by the short length of the polypeptide chain and the high degree of unusual post-translational modifications. The cyclization of the polypeptide chain through a single disulphide bond, the presence of two conserved Pro residues, and the epimerization of a Trp/Leu residue confer to Contryphans a stable and well-defined structure in solution, conserved in all members of the family, and tolerant to multiple substitutions. The potential of Contryphans as scaffolds for the design of redox-active (macro)molecules was tested by engineering a copper-binding site on two different variants of the natural peptide Contryphan-Vn. The binding site was designed by computational modeling, and the redesigned peptides were synthesized and characterized by optical, fluorescence, electron spin resonance, and nuclear magnetic resonance spectroscopy. The novel peptides, named Cupryphan and Arg-Cupryphan, bind Cu(2+) ions with a 1:1 stoichiometry and a K(d) in the 100 nM range. Other divalent metals (e.g., Zn(2+) and Mg(2+)) are bound with much lower affinity. In addition, Cupryphans catalyze the dismutation of superoxide anions with an activity comparable to other nonpeptidic superoxide dismutase mimics. We conclude that the Contryphan motif represents a natural robust scaffold which can be engineered to perform different functions, providing additional means for the design of catalytically active mini metalloproteins.

  10. Analysis of social relations among organizational units derived from process models and redesign of organization structure

    NARCIS (Netherlands)

    Choi, I.; Song, M.S.; Kim, K.M.; Lee, Y-H.

    2007-01-01

    Despite surging interests in analyzing business processes, there are few scientific approaches to analysis and redesign of organizational structures which can greatly affect the performance of business processes. This paper presents a method for deriving and analyzing organizational relations from

  11. Redesigning Acquisition Processes: A New Methodology Based on the Flow of Knowledge and Information

    National Research Council Canada - National Science Library

    Kock, Ned F; Murphy, Frederic

    2001-01-01

    Current business process redesign practices, in the defense sector as well as in business in general, are based on several assumptions inherited from Taylor s scientific management method, including...

  12. Feasibility study for the redesign of MDOT's pavement management systems software.

    Science.gov (United States)

    2011-04-01

    In August of 2006 the Mississippi Department of Transportation (MDOT) initiated State Study No. 191, entitled Feasibility : Study for the Redesign of MDOTs Pavement Management System (PMS) Software. At the initiation of this study, the : Dep...

  13. Lean thinking across a hospital: redesigning care at the Flinders Medical Centre.

    Science.gov (United States)

    Ben-Tovim, David I; Bassham, Jane E; Bolch, Denise; Martin, Margaret A; Dougherty, Melissa; Szwarcbord, Michael

    2007-02-01

    Lean thinking is a method for organising complex production processes so as to encourage flow and reduce waste. While the principles of lean thinking were developed in the manufacturing sector, there is increasing interest in its application in health care. This case history documents the introduction and development of Redesigning Care, a lean thinking-based program to redesign care processes across a teaching general hospital. Redesigning Care has produced substantial benefits over the first two-and-a-half years of its implementation, making care both safer and more accessible. Redesigning Care has not been aimed at changing the specifics of clinical practice. Rather, it has been concerned with improving the flow of patients through clinical and other systems. Concepts that emerged in the manufacturing sector have been readily translatable into health care. Lean thinking may play an important role in the reform of health care in Australia and elsewhere.

  14. Organizational Contexts and Texts: The Redesign of the Midwest Bell Telephone Bill.

    Science.gov (United States)

    Keller-Cohen, Deborah

    1987-01-01

    Offers a retrospective view of organizational factors affecting the redesign of the Midwest Bell Telephone Bill. Shows how financial considerations, organizational time frame, and employee training and experience influenced the bill's development process. (MM)

  15. OhioHealth web site wins awards. Draws leadership recognition for outstanding redesign.

    Science.gov (United States)

    Rees, Tom

    2004-01-01

    OhioHealth, Columbus, Ohio, has redesigned its web site, making it especially useful and appealing to women. For the collaborative effort, which included the Mayo Clinic and The VIA Group, Portland Maine, it has received numerous awards.

  16. Ice Cores

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Records of past temperature, precipitation, atmospheric trace gases, and other aspects of climate and environment derived from ice cores drilled on glaciers and ice...

  17. From Telecourses to Online Courses: A Story of Redesign | Du cours télévisé au cours en ligne : une histoire de redesign

    Directory of Open Access Journals (Sweden)

    Claude Potvin

    2015-11-01

    Full Text Available This case deals with the redesign of a standard telecourse - printed material, professional studio video recordings and phone tutoring – into an online course. The redesign involved an adjunct professor in the Humanities having some experience in distance education but little with learning technologies. It was a two-year project including the grant application process. The main issues included replacing television-based content with multimedia content; understanding the complexity of interactions between materials, students, and tutors; and adapting traditional assessment approaches to online instruments and methods.

  18. Using Technology, Clinical Workflow Redesign, and Team Solutions to Achieve the Patient Centered Medical Home

    Science.gov (United States)

    2011-01-01

    Redesign, and Team Solutions to Achieve the Patient Centered Medical Home LTC Nicole Kerkenbush, MHA, MN Army Medical Department, Office of the...TITLE AND SUBTITLE Using Technology, Clinical Workflow Redesign, and Team Solutions to Achieve the Patient Centered Medical Home 5a. CONTRACT...Describe how these tools are being used to implement the Patient Centered Medical Home care model 2 2011 MHS Conference MEDCOM AHLTA Provider Satisfaction

  19. Methodology and findings of the NRC`s materials licensing process redesign

    Energy Technology Data Exchange (ETDEWEB)

    Rathbun, P.A.; Brown, K.D.; Madera, J.R.; Moriarty, M.; Pelchat, J.M.; Usilton, W.K.; Whitten, J.E.; Vacca, P.C.

    1996-04-01

    This report describes the work and vision of the team chartered to redesign the process for licensing users of nuclear materials. The Business Process Redesign team was chartered to improve the speed of the existing licensing process while maintaining or improving public safety and to achieve required resource levels. The report describes the team`s methods for acquiring and analyzing information about the existing materials licensing process and the steps necessary to radically change this process to the envisioned future process.

  20. Color-tunable up-conversion emission of luminescent-plasmonic, core/shell nanomaterials – KY{sub 3}F{sub 10}:Yb{sup 3+},Tm{sup 3+}/SiO{sub 2}-NH{sub 2}/Au

    Energy Technology Data Exchange (ETDEWEB)

    Runowski, Marcin, E-mail: runowski@amu.edu.pl

    2017-06-15

    Multifunctional luminescent-plasmonic KY{sub 3}F{sub 10}:Yb{sup 3+},Tm{sup 3+}/SiO{sub 2}-NH{sub 2}/Au nanomaterials were successfully obtained. The lanthanide-doped fluoride nanoparticles (NPs), synthesized under hydrothermal conditions exhibited bright blue up-conversion luminescence (λ{sub ex}=980 nm). Such lanthanide nanocrystals (20–40 nm) were coated with amine modified silica shell, forming core/shell nanostructures. Their surface was further uniformly covered with ultra-small gold NPs (4–7 nm). The as-prepared luminescent-plasmonic core/shell nanomaterials exhibited tunable up-conversion emission, due to the interactions between plasmonic and luminescent phases. The emission of Tm{sup 3+} ion was affected by the surface Au NPs, which exhibited strong plasmonic absorption in the visible range (450–650 nm). The increasing amount of the surface Au NPs, led to the significant alterations in a ratio of the Tm{sup 3+} emission bands. The NIR band ({sup 3}H{sub 4}→{sup 3}H{sub 6}) was unchanged, whereas the ratio and relative intensity of the bands in a visible range ({sup 1}G{sub 4}→{sup 3}H{sub 6} and {sup 1}G{sub 4}→{sup 3}F{sub 4}) was altered. This led to the significant change of the emission spectra shape and influenced color of emission, tuning it from bright blue to blue-violet. The products obtained were characterized by transmission electron microscopy (TEM), energy dispersive X-ray analysis (EDX), powder X-ray diffraction (XRD), UV–vis absorption spectroscopy and luminescence spectroscopy (excitation/emission spectra and luminescence decay curves).

  1. Concept for the redesign of ECOMAN (standby losses) - Final report; Konzepte fuer Redesign ECOMAN (Standby-Verluste) - Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Ernst, D.; Haerri, V.V.; Riesen, H.

    2008-04-15

    A lot of electronic devices are equipped with a so called standby mode. In this mode a device can easily be brought into full functionality directly, by remote control or by timer. Unfortunately, the standby mode implies a high consumption of electrical energy that could be reduced 10 to 20 times by an adequate technology. In Switzerland these losses amount to approximately 1,900 GWh. The so called ECOMAN is an electronic device which can reduce these losses effectively and comfortably. Due to political pressure the producers of electronic devices are forced to find solutions for the problem of standby losses. The ECOMAN would thus be of less importance because the problem would be solved at its roots. This fact and the wish to have a better performance led to a new definition of this device. The ECOMAN has to be improved and shall offer additional functions. E.g. it shall protect the devices from fire hazard or serve as control in the field of building automation. The new concepts were well accepted by the producer who already realized the specification of the first phase of redesign, which serves as basis for the further development of integration. (author)

  2. OSIRIS: an example of gradual conversion

    International Nuclear Information System (INIS)

    Guidez, J.; Beylot, J.; Joly, C.

    1997-01-01

    The conversion of the OSIRIS core from 'Caramel' to silicide forms part of the move towards standardising a well-known fuel, developed in the context of the RERTR programme, and used by the majority of reactors. This standardisation makes it possible to anticipate reduced manufacturing and reprocessing costs in the long term. (author)

  3. Conceptual design study of high conversion light water reactor

    International Nuclear Information System (INIS)

    Okumura, Keisuke; Akie, Hiroshi; Mori, Takamasa; Nakagawa, Masayuki; Ishiguro, Yukio

    1990-06-01

    Since 1984, R and D work has been made for high conversion light water reactors (HCLWRs), at JAERI, to improve the natural uranium saving and effective plutonium utilization by the use of conventional or extended LWR technology. This report summarizes the results of the feasibility study made mainly from the viewpoint of nuclear design in the Phase-I Program (1985∼1989). Until now, the following various types of HCLWR core concepts have been investigated; 1) homogeneous core with tight pitch lattice of fuel rods, 2) homogeneous core with semi-tight pitch lattice, 3) spectral shift core using fertile rod with semi-tight pitch lattice, 4) flat-core, 5) axial heterogeneous core. The core burnup and thermohydraulic analyses during normal operations have been performed to clear up the burnup performances and feasibility for each core. Based on the analysis results, the axial heterogeneous HCLWR core was selected as the JAERI reference core. (author)

  4. Special issue: Plasma Conversion

    NARCIS (Netherlands)

    Nozaki, T.; Bogaerts, A.; Tu, X.; van de Sanden, M. C. M.

    2017-01-01

    With growing concern of energy and environmental issues, the combination of plasma and heterogeneous catalysts receives special attention in greenhouse gas conversion, nitrogen fixation and hydrocarbon chemistry. Plasma gas conversion driven by renewable electricity is particularly important for the

  5. A Model for Conversation

    DEFF Research Database (Denmark)

    Ayres, Phil

    2012-01-01

    This essay discusses models. It examines what models are, the roles models perform and suggests various intentions that underlie their construction and use. It discusses how models act as a conversational partner, and how they support various forms of conversation within the conversational activity...

  6. Direct Conversion of Energy.

    Science.gov (United States)

    Corliss, William R.

    This publication is one of a series of information booklets for the general public published by the United States Atomic Energy Commission. Direct energy conversion involves energy transformation without moving parts. The concepts of direct and dynamic energy conversion plus the laws governing energy conversion are investigated. Among the topics…

  7. The Nature of Primary Students' Conversation in Technology Education

    Science.gov (United States)

    Fox-Turnbull, Wendy H.

    2016-01-01

    Classroom conversations are core to establishing successful learning for students. This research explores the nature of conversation in technology education in the primary classroom and the implications for teaching and learning. Over a year, two units of work in technology were taught in two primary classrooms. Most data was gathered in Round 2…

  8. Reactor core

    International Nuclear Information System (INIS)

    Matsuura, Tetsuaki; Nomura, Teiji; Tokunaga, Kensuke; Okuda, Shin-ichi

    1990-01-01

    Fuel assemblies in the portions where the gradient of fast neutron fluxes between two opposing faces of a channel box is great are kept loaded at the outermost peripheral position of the reactor core also in the second operation cycle in the order to prevent interference between a control rod and the channel box due to bending deformation of the channel box. Further, the fuel assemblies in the second row from the outer most periphery in the first operation cycle are also kept loaded at the second row in the second operation cycle. Since the gradient of the fast neutrons in the reactor core is especially great at the outer circumference of the reactor core, the channel box at the outer circumference is bent such that the surface facing to the center of the reactor core is convexed and the channel box in the second row is also bent to the identical direction, the insertion of the control rod is not interfered. Further, if the positions for the fuels at the outermost periphery and the fuels in the second row are not altered in the second operation cycle, the gaps are not reduced to prevent the interference between the control rod and the channel box. (N.H.)

  9. Elements of energy conversion

    CERN Document Server

    Russell, Charles R

    2013-01-01

    Elements of Energy Conversion brings together scattered information on the subject of energy conversion and presents it in terms of the fundamental thermodynamics that apply to energy conversion by any process. Emphasis is given to the development of the theory of heat engines because these are and will remain most important power sources. Descriptive material is then presented to provide elementary information on all important energy conversion devices. The book contains 10 chapters and opens with a discussion of forms of energy, energy sources and storage, and energy conversion. This is foll

  10. Iterated multidimensional wave conversion

    International Nuclear Information System (INIS)

    Brizard, A. J.; Tracy, E. R.; Johnston, D.; Kaufman, A. N.; Richardson, A. S.; Zobin, N.

    2011-01-01

    Mode conversion can occur repeatedly in a two-dimensional cavity (e.g., the poloidal cross section of an axisymmetric tokamak). We report on two novel concepts that allow for a complete and global visualization of the ray evolution under iterated conversions. First, iterated conversion is discussed in terms of ray-induced maps from the two-dimensional conversion surface to itself (which can be visualized in terms of three-dimensional rooms). Second, the two-dimensional conversion surface is shown to possess a symplectic structure derived from Dirac constraints associated with the two dispersion surfaces of the interacting waves.

  11. High conversion burner type reactor

    International Nuclear Information System (INIS)

    Higuchi, Shin-ichi; Kawashima, Masatoshi

    1987-01-01

    Purpose: To simply and easily dismantle and reassemble densified fuel assemblies taken out of a high conversion ratio area thereby improve the neutron and fuel economy. Constitution: The burner portion for the purpose of fuel combustion is divided into a first burner region in adjacent with the high conversion ratio area at the center of the reactor core, and a second burner region formed to the outer circumference thereof and two types of fuels are charged therein. Densified fuel assemblies charged in the high conversion ratio area are separatably formed as fuel assemblies for use in the two types of burners. In this way, dense fuel assembly is separated into two types of fuel assemblies for use in burner of different number and arranging density of fuel elements which can be directly charged to the burner portion and facilitate the dismantling and reassembling of the fuel assemblies. Further, since the two types of fuel assemblies are charged in the burner portion, utilization factor for the neutron fuels can be improved. (Kamimura, M.)

  12. Analysis Of Core Management For The Transition Cores Of RSG-GAS Reactor To Full-Silicide Core

    International Nuclear Information System (INIS)

    Malem Sembiring, Tagor; Suparlina, Lily; Tukiran

    2001-01-01

    The core conversion of RSG-GAS reactor from oxide to silicide core with meat density of 2.96 g U/cc is still doing. At the end of 2000, the reactor has been operated for 3 transition cores which is the mixed core of oxide-silicide. Based on previous work, the calculated core parameter for the cores were obtained and it is needed 10 transition cores to achieve a full-silicide core. The objective of this work is to acquire the effect of the increment of the number of silicide fuel on the core parameters such as excess reactivity and shutdown margin. The measurement of the core parameters was carried out using the method of compensation of couple control rods. The experiment shows that the excess reactivity trends lower with the increment of the number of silicide fuel in the core. However, the shutdown margin is not change with the increment of the number of silicide fuel. Therefore, the transition cores can be operated safety to a full-silicide core

  13. Aerodynamic Analysis and Three-Dimensional Redesign of a Multi-Stage Axial Flow Compressor

    Directory of Open Access Journals (Sweden)

    Tao Ning

    2016-04-01

    Full Text Available This paper describes the introduction of three-dimension (3-D blade designs into a 5-stage axial compressor with multi-stage computational fluid dynamic (CFD methods. Prior to a redesign, a validation study is conducted for the overall performance and flow details based on full-scale test data, proving that the multi-stage CFD applied is a relatively reliable tool for the analysis of the follow-up redesign. Furthermore, at the near stall point, the aerodynamic analysis demonstrates that significant separation exists in the last stator, leading to the aerodynamic redesign, which is the focus of the last stator. Multi-stage CFD methods are applied throughout the three-dimensional redesign process for the last stator to explore their aerodynamic improvement potential. An unconventional asymmetric bow configuration incorporated with leading edge re-camber and re-solidity is employed to reduce the high loss region dominated by the mainstream. The final redesigned version produces a 13% increase in the stall margin while maintaining the efficiency at the design point.

  14. System redesign of the immunization supply chain: Experiences from Benin and Mozambique.

    Science.gov (United States)

    Prosser, Wendy; Jaillard, Philippe; Assy, Emmanuelle; Brown, Shawn T; Matsinhe, Graça; Dekoun, Mawutondji; Lee, Bruce Y

    2017-04-19

    Evidence suggests that immunization supply chains are becoming outdated and unable to deliver needed vaccines due to growing populations and new vaccine introductions. Redesigning a supply chain could result in meeting current demands. The Ministries of Health in Benin in Mozambique recognized known barriers to the immunization supply chain and undertook a system redesign to address those barriers. Changes were made to introduce an informed push system while consolidating storage points, introducing transport loops, and increasing human resource capacity for distribution. Evaluations were completed in each country. Evaluation in each country indicated improved performance of the supply chain. The Effective Vaccine Management (EVM) assessment in Benin documented notable improvements in the distribution criteria of the tool, increasing from 40% to 100% at the district level. In Mozambique, results showed reduced stockouts at health facility level from 79% at baseline to less than 1% at endline. Coverage rates of DTP3 also increased from 68.9% to 92.8%. Benin and Mozambique are undertaking system redesign in order to respond to constraints identified in the vaccine supply chain. Results and learnings show improvements in supply chain performance and make a strong case for system redesign. These countries demonstrate the feasibility of system redesign for other countries considering how to address outdated supply chains. Copyright © 2017 The Author(s). Published by Elsevier Ltd.. All rights reserved.

  15. Application of participatory ergonomics to the redesign of the family-centred rounds process.

    Science.gov (United States)

    Xie, Anping; Carayon, Pascale; Cox, Elizabeth D; Cartmill, Randi; Li, Yaqiong; Wetterneck, Tosha B; Kelly, Michelle M

    2015-01-01

    Participatory ergonomics (PE) can promote the application of human factors and ergonomics (HFE) principles to healthcare system redesign. This study applied a PE approach to redesigning the family-centred rounds (FCR) process to improve family engagement. Various FCR stakeholders (e.g. patients and families, physicians, nurses, hospital management) were involved in different stages of the PE process. HFE principles were integrated in both the content (e.g. shared mental model, usability, workload consideration, systems approach) and process (e.g. top management commitment, stakeholder participation, communication and feedback, learning and training, project management) of FCR redesign. We describe activities of the PE process (e.g. formation and meetings of the redesign team, data collection activities, intervention development, intervention implementation) and present data on PE process evaluation. To demonstrate the value of PE-based FCR redesign, future research should document its impact on FCR process measures (e.g. family engagement, round efficiency) and patient outcome measures (e.g. patient satisfaction).

  16. Application of participatory ergonomics to the redesign of the family-centered rounds process

    Science.gov (United States)

    Xie, Anping; Carayon, Pascale; Cox, Elizabeth D.; Cartmill, Randi; Li, Yaqiong; Wetterneck, Tosha B.; Kelly, Michelle M.

    2015-01-01

    Participatory ergonomics (PE) can promote the application of human factors and ergonomics (HFE) principles to healthcare system redesign. This study applied a PE approach to redesigning the family-centered rounds (FCR) process to improve family engagement. Various FCR stakeholders (e.g., patients and families, physicians, nurses, hospital management) were involved in different stages of the PE process. HFE principles were integrated in both the content (e.g., shared mental model, usability, workload consideration, systems approach) and process (e.g., top management commitment, stakeholder participation, communication and feedback, learning and training, project management) of FCR redesign. We describe activities of the PE process (e.g., formation and meetings of the redesign team, data collection activities, intervention development, intervention implementation) and present data on PE process evaluation. To demonstrate the value of PE-based FCR redesign, future research should document its impact on FCR process measures (e.g., family engagement, round efficiency) and patient outcome measures (e.g., patient satisfaction). PMID:25777042

  17. HEU to LEU fuel conversion. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Mulder, R.U.

    1994-10-01

    The Nuclear Regulatory Commission issued a ruling, effective March 27, 1986, that all U.S. non-power reactors convert from HEU fuel to LEU fuel. A Reduced Enrichment for Research and Test Reactors Program was conducted by the Department of Energy at Argonne National Laboratory to coordinate the development of the high density LEU fuel and assist in the development of Safety Analysis Reports for the smaller non-power reactors. Several meetings were held at Argonne in 1987 with the non-power reactor community to discuss the conversion and to set up a conversion schedule for university reactors. EG&G at Idaho was assigned the coordination of the fuel element redesigns. The fuel elements were manufactured by the Babcock & Wilcox Company in Lynchburg, Virginia. The University of Virginia was awarded a grant by the DOE Idaho Operations Office in 1988 to perform safety analysis studies for the LEU conversion for its 2 MW UVAR and 100 Watt CAVALIER reactors. The University subsequently decided to shut down the CAVALIER reactor. A preliminary SAR on the UVAR, along with Technical Specification changes, was submitted to the NRC in November, 1990. An updated SAR was approved by the NRC in January, 1991. In September, 1992, representatives from the fuel manufacturer (B&W) and the fuel designer (EG&G, Idaho) came to the UVAR facility to observe trial fittings of new 22 plate LEU mock fuel elements. B&W fabricated two non-fuel bearing elements, a regular 22 plate element and a control rod element. The elements were checked against the drawings and test fitted in the UVAR grid plate. The dimensions were acceptable and the elements fit in the grid plate with no problems. The staff made several suggestions for minor construction changes to the end pieces on the elements, which were incorporated into the final design of the actual fuel elements. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

  18. HEU to LEU fuel conversion. Final report

    International Nuclear Information System (INIS)

    Mulder, R.U.

    1994-10-01

    The Nuclear Regulatory Commission issued a ruling, effective March 27, 1986, that all U.S. non-power reactors convert from HEU fuel to LEU fuel. A Reduced Enrichment for Research and Test Reactors Program was conducted by the Department of Energy at Argonne National Laboratory to coordinate the development of the high density LEU fuel and assist in the development of Safety Analysis Reports for the smaller non-power reactors. Several meetings were held at Argonne in 1987 with the non-power reactor community to discuss the conversion and to set up a conversion schedule for university reactors. EG ampersand G at Idaho was assigned the coordination of the fuel element redesigns. The fuel elements were manufactured by the Babcock ampersand Wilcox Company in Lynchburg, Virginia. The University of Virginia was awarded a grant by the DOE Idaho Operations Office in 1988 to perform safety analysis studies for the LEU conversion for its 2 MW UVAR and 100 Watt CAVALIER reactors. The University subsequently decided to shut down the CAVALIER reactor. A preliminary SAR on the UVAR, along with Technical Specification changes, was submitted to the NRC in November, 1990. An updated SAR was approved by the NRC in January, 1991. In September, 1992, representatives from the fuel manufacturer (B ampersand W) and the fuel designer (EG ampersand G, Idaho) came to the UVAR facility to observe trial fittings of new 22 plate LEU mock fuel elements. B ampersand W fabricated two non-fuel bearing elements, a regular 22 plate element and a control rod element. The elements were checked against the drawings and test fitted in the UVAR grid plate. The dimensions were acceptable and the elements fit in the grid plate with no problems. The staff made several suggestions for minor construction changes to the end pieces on the elements, which were incorporated into the final design of the actual fuel elements. Selected papers are indexed separately for inclusion in the Energy Science and Technology

  19. A study in usability: redesigning a health sciences library's mobile site.

    Science.gov (United States)

    Rosario, Jovy-Anne; Ascher, Marie T; Cunningham, Diana J

    2012-01-01

    A mobile site redesign was conducted at a medium-sized academic health sciences library with the goal of creating a site that meets the mobile information needs of its users. The redesign phases included (1) needs assessment, (2) usability testing, and (3) site design. The survey results showed that Apple devices were the most prevalent; the most desirable activities performed on a mobile site were searching for articles, accessing full-text articles and e-books, searching databases, and searching the catalog. These activities guided the development of the usability testing tasks and the redesign. All phases were completed within six months, and the total project cost was $50 for incentive purchases. Copyright © Taylor & Francis Group, LLC

  20. Reinventing the Wheel: One Program's Approach to Redesign of Didactic Courses.

    Science.gov (United States)

    Hudak, Nicholas M; Scott, Victoria; Spear, Sherrie B; Hills, Karen J

    2015-12-01

    Curriculum and course redesign are expected and intentional efforts in health professions education. For physician assistant (PA) education, ongoing program self-assessment is a required accreditation standard and may guide deliberate changes within curriculum. The purpose of this article is to describe one PA program’s approach to the redesign of 4 courses into 3 courses that span the entire didactic phase. Significant lessons learned include the importance of planning ahead, identifying key players, documenting the process as part of ongoing self-assessment, competency mapping, and being prepared to make real-time modifications and changes based on course evaluations and faculty feedback. Our approach and guiding principles to the successful redesign of the didactic courses may provide both established and new PA educational programs with useful methods to apply in their own unique curricula.

  1. Full-spectrum volumetric solar thermal conversion via photonic nanofluids.

    Science.gov (United States)

    Liu, Xianglei; Xuan, Yimin

    2017-10-12

    Volumetric solar thermal conversion is an emerging technique for a plethora of applications such as solar thermal power generation, desalination, and solar water splitting. However, achieving broadband solar thermal absorption via dilute nanofluids is still a daunting challenge. In this work, full-spectrum volumetric solar thermal conversion is demonstrated over a thin layer of the proposed 'photonic nanofluids'. The underlying mechanism is found to be the photonic superposition of core resonances, shell plasmons, and core-shell resonances at different wavelengths, whose coexistence is enabled by the broken symmetry of specially designed composite nanoparticles, i.e., Janus nanoparticles. The solar thermal conversion efficiency can be improved by 10.8% compared with core-shell nanofluids. The extinction coefficient of Janus dimers with various configurations is also investigated to unveil the effects of particle couplings. This work provides the possibility to achieve full-spectrum volumetric solar thermal conversion, and may have potential applications in efficient solar energy harvesting and utilization.

  2. High conversion HTRs and their fuel cycle

    International Nuclear Information System (INIS)

    Gutmann, H.; Hansen, U.; Larsen, H.; Price, M.S.T.

    1975-01-01

    This report discusses the principles of the core design and the fuel cycle layout for High Conversion HTRs (HCHTRs). Though most of the principles apply equally to HTRs of the pebble-bed and the prismatic fuel element design types, the paper concentrates on the latter. Design and fuel cycle strategies for the full utilisation of the high conversion potential are compared with others that aim at easier reprocessing and the 'environmental' fuel cycle. The paper concludes by discussing operating and fuel cycle characteristics and economics of HCHTRs, and how the latter impinge on the allowable price for uranium ore and the available uranium resources. (orig./UA) [de

  3. Aplikasi Ergonomic Function Deployment (Efd Pada Redesign Alat Parut Kelapa Untuk Ibu Rumah Tangga

    Directory of Open Access Journals (Sweden)

    Roberta Zulfhi Surya

    2015-04-01

    Ergonomic Function Deployment (Efd Application In Coconut Grater Redesign For HousewifeAbstract. Pulverizing (coconut grated is one of daily kitchen worksconducted by housewives. A common existing coconut grater which is available on the market is normally works using a crank system. Housewives have complaints of pain in the limbs, especially the hands, waist and back after using this grater. This study aims to improve the design of coconut grater with Ergonomic Function Deployment (EFD based system and determine the housewife musculoskeletal decline as users. Further, to examine pulverizing time difference after redesign. The study was conducted at RT. 001 RW. 005 West Tembilahan Hulu village, subdistrict Tembilahan Indragiri Hilir. The method use in this study is same design subject (treatment by subjects design with co added Colton equation. Atotal of 12 housewives were used and subjected to the calculation. A grater redesign with EFD system was obtained by creating House of Ergonomic (HOE matrices and determining the anthropometric data. Whilst musculoskeletal disorders were obtained by generating Nordic Body Map (NBMworksheets questionnaire. Moreover, pulverizing time was obtained by testing coconut graterused before and after redesign. Results of the study showed that the redesign tool based on Ergonomic Function Deployment (EFD systemwasfound to be more convenient form which five ergonomics aspects required was fulfilled: effective, convenient, safe, healthy, and efficient (ENASE. Housewife musculoskeletal complaints decreased by 0.285% or 17.39%. This study also shows that coconut pulverizing time is 5 minutes faster and increased by 30.10% after redesigning the coconut grater crank system.

  4. Computers and conversation

    CERN Document Server

    Luff, Paul; Gilbert, Nigel G

    1986-01-01

    In the past few years a branch of sociology, conversation analysis, has begun to have a significant impact on the design of human*b1computer interaction (HCI). The investigation of human*b1human dialogue has emerged as a fruitful foundation for interactive system design.****This book includes eleven original chapters by leading researchers who are applying conversation analysis to HCI. The fundamentals of conversation analysis are outlined, a number of systems are described, and a critical view of their value for HCI is offered.****Computers and Conversation will be of interest to all concerne

  5. Preliminary design package for residential heating/cooling system: Rankine air conditioner redesign

    Science.gov (United States)

    1978-01-01

    A summary of the preliminary redesign and development of a marketable single family heating and cooling system is presented. The interim design and schedule status of the residential (3-ton) redesign, problem areas and solutions, and the definition of plans for future design and development activities were discussed. The proposed system for a single-family residential heating and cooling system is a single-loop, solar-assisted, hydronic-to-warm-air heating subsystem with solar-assisted domestic water heating and a Rankine-driven expansion air-conditioning subsystem.

  6. Experiences of primary care physicians and staff following lean workflow redesign.

    Science.gov (United States)

    Hung, Dorothy Y; Harrison, Michael I; Truong, Quan; Du, Xue

    2018-04-10

    In response to growing pressures on primary care, leaders have introduced a wide range of workforce and practice innovations, including team redesigns that delegate some physician tasks to nonphysicians. One important question is how such innovations affect care team members, particularly in view of growing dissatisfaction and burnout among healthcare professionals. We examine the work experiences of primary care physicians and staff after implementing Lean-based workflow redesigns. This included co-locating physician and medical assistant dyads, delegating significant responsibilities to nonphysician staff, and mandating greater coordination and communication among all care team members. The redesigns were implemented and scaled in three phases across 46 primary care departments in a large ambulatory care delivery system. We fielded 1164 baseline and 1333 follow-up surveys to physicians and other nonphysician staff (average 73% response rate) to assess workforce engagement (e.g., job satisfaction, motivation), perceptions of the work environment, and job-related burnout. We conducted multivariate regressions to detect changes in experiences after the redesign, adjusting for respondent characteristics and clustering of within-clinic responses. We found that both physicians and nonphysician staff reported higher levels of engagement and teamwork after implementing redesigns. However, they also experienced higher levels of burnout and perceptions of the workplace as stressful. Trends were the same for both occupational groups, but the increased reports of stress were greater among physicians. Additionally, members of all clinics, except for the pilot site that developed the new workflows, reported higher burnout, while perceptions of workplace stress increased in all clinics after the redesign. Our findings partially align with expectations of work redesign as a route to improving physician and staff experiences in delivering care. Although teamwork and engagement

  7. Preliminary design package for residential heating/cooling system--Rankine air conditioner redesign

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-01

    This report contains a summary of the preliminary redesign and development of a marketable single-family heating and cooling system. The objectives discussed are the interim design and schedule status of the Residential (3-ton) redesign, problem areas and solutions, and the definition of plans for future design and development activities. The proposed system for a single-family residential heating and cooling system is a single-loop, solar-assisted, hydronic-to-warm-air heating subsystem with solar-assisted domestic water heating and a Rankine-driven expansion air-conditioning subsystem.

  8. Core BPEL

    DEFF Research Database (Denmark)

    Hallwyl, Tim; Højsgaard, Espen

    The Web Services Business Process Execution Language (WS-BPEL) is a language for expressing business process behaviour based on web services. The language is intentionally not minimal but provides a rich set of constructs, allows omission of constructs by relying on defaults, and supports language......, does not allow omissions, and does not contain ignorable elements. We do so by identifying syntactic sugar, including default values, and ignorable elements in WS-BPEL. The analysis results in a translation from the full language to the core subset. Thus, we reduce the effort needed for working...

  9. 25 CFR 20.203 - Can a tribe incorporate assistance from other sources into a tribal redesign plan?

    Science.gov (United States)

    2010-04-01

    ...-477 federal funding sources) in the plan. ... 25 Indians 1 2010-04-01 2010-04-01 false Can a tribe incorporate assistance from other sources... tribe incorporate assistance from other sources into a tribal redesign plan? Yes, when a tribe redesigns...

  10. Energy conversion alternatives study

    Science.gov (United States)

    Shure, L. T.

    1979-01-01

    Comparison of coal based energy systems is given. Study identifies and compares various advanced energy conversion systems using coal or coal derived fuels for baselaoad electric power generation. Energy Conversion Alternatives Study (ECAS) reports provede government, industry, and general public with technically consistent basis for comparison of system's options of interest for fossilfired electric-utility application.

  11. Hydrothermal conversion of biomass

    NARCIS (Netherlands)

    Knezevic, D.

    2009-01-01

    This thesis presents research of hydrothermal conversion of biomass (HTC). In this process, hot compressed water (subcritical water) is used as the reaction medium. Therefore this technique is suitable for conversion of wet biomass/ waste streams. By working at high pressures, the evaporation of

  12. Conversations in African Philosophy

    African Journals Online (AJOL)

    JONATHAN

    Conversational philosophy is articulated by Jonathan O. Chimakonam as the new wave of philosophical practice both in “place” and in “space”. This journal adopts and promotes this approach to philosophizing for African philosophy. Readers are encouraged to submit their conversational piece (maximum of 2000 words) ...

  13. Microwave plasma mode conversion

    International Nuclear Information System (INIS)

    Torres, H.S.; Sakanaka, P.H.; Villarroel, C.H.

    1985-01-01

    The behavior of hot electrons during the process of laser-produced plasma is studied. The basic equations of mode conversion from electromagnetic waves to electrostatic waves are presented. It is shown by mode conversion, that, the resonant absorption and parametric instabilities appear simultaneously, but in different plasma regions. (M.C.K.) [pt

  14. Political conversations on Facebook

    DEFF Research Database (Denmark)

    Sørensen, Mads P.

    2016-01-01

    Political conversations are according to theories on deliberative democracy essential to well-functioning democracies. Traditionally these conversations have taken place in face-to-face settings, in e.g. party meetings and town meetings. However, social media such as Facebook and Twitter offers new...... possibilities for online political conversations between citizens and politicians. This paper examines the presence on Facebook and Twitter of Members of the Danish national Parliament, the Folketing, and focusses on a quantitative mapping of the political conversation activities taking place in the threads...... following Facebook posts from Danish Members of Parliament (MPs). The paper shows that, in comparison with previous findings from other countries, Danish MPs have a relatively high degree of engagement in political conversations with citizens on Facebook – and that a large number of citizens follow MPs...

  15. Client perceptions of a work rehabilitation programme for women: the Redesigning Daily Occupations (ReDO) project.

    Science.gov (United States)

    Wästberg, Birgitta A; Erlandsson, Lena-Karin; Eklund, Mona

    2013-03-01

    The Redesigning Daily Occupations programme (ReDO) is a Swedish work rehabilitation programme for women on sick leave due to stress-related disorders. The aim of the study was to investigate the participants' perceptions of taking part in the work rehabilitation programme. Seven of the 38 women who completed ReDO were interviewed during and after the programme. The interviews were analysed by manifest and latent content analysis. The informants were satisfied with the content of the programme and the support they received in the programme and when returning to work. The women thought they had become more aware of what they did during a day and how they performed their daily activities, which helped them to change their ways of performing them. The result highlighted different parts of their rehabilitation process which constituted four sub-themes: "Perceptions of the ReDO", "The intrinsic process", "Person-related changes", and "Perceptions of returning to work", and formed the core theme "Critical parts of the rehabilitation process". The findings may not be generalized to other settings and future research should further investigate work rehabilitation for the target group.

  16. High enrichment to low enrichment core's conversion. Grid seismic calculation

    International Nuclear Information System (INIS)

    Magoia, J.E.; Benito, G.D.

    1990-01-01

    The grid of a reactor under severe seismic conditions was structurally verified, considering that it must have been maintained without failure. Values obtained from tensions and displacements are under the admissible ones, the existing grid responds to the structural assessment before a severe S2 earthquake (OIEA classification). (Author) [es

  17. From Course Assessment to Redesign: A Hybrid-Vehicle Course as a Case Illustration

    Science.gov (United States)

    Stanton, Ken C.; Bradley, Thomas H.

    2013-01-01

    Assessment has become a central aspect of engineering education for evaluating student learning, attaining accreditation, and ensuring accountability. However, the final step of the assessment process, which requires assessment results be used to redesign courses and programmes, is appreciably underdeveloped in the literature. As such, this work…

  18. Redesign of Work for Educational Purposes and for Quality of Working Life

    Science.gov (United States)

    Taylor, James C.

    1976-01-01

    Examples of successful implementation of sociotechnical design of workplaces indicate that workplaces can be redesigned to achieve a closer match between employee values and organizational work roles. Organizational effectiveness does not seem to be sacrificed as a consequence of such action. (Author/JDS)

  19. Preliminary Assessment of the Emporium Model in a Redesigned Engineering Mechanics Course

    Science.gov (United States)

    Rais-Rohani, Masoud; Walters, Andrew

    2014-01-01

    A lecture-based engineering mechanics course (Statics) is redesigned using the Emporium model. Whereas students study the material outside of class via asynchronous online delivery of the content and instructional videos, they do all the other activities (e.g., assignments, tests) either individually or in groups inside the classroom. Computer-…

  20. A Study on Situated Cognition: Product Dissection's Effect on Redesign Activities

    Science.gov (United States)

    Grantham, Katie; Okudan Kremer, Gül E.; Simpson, Timothy W.; Ashour, Omar

    2013-01-01

    Situated cognition theory describes the context of a learning activity's effect on learner's cognition. In this paper, we use situated cognition theory to examine the effect of product dissection on product redesign activities. Two specific research questions are addressed: 1) Does situated cognition, in the form of product dissection, improve…

  1. Development of consensus guidance to facilitate service redesign around pharmacist prescribing in UK hospital practice.

    Science.gov (United States)

    Tonna, Antonella; McCaig, Dorothy; Diack, Lesley; West, Bernice; Stewart, Derek

    2014-10-01

    The last decade has seen a drive towards non-medical prescribing in the United Kingdom (UK). However, there is a dearth of any published literature on applying the principles of service redesign to support pharmacist prescribing in any sphere of practice. To develop consensus guidance to facilitate service redesign around pharmacist prescribing. UK hospital practice. The Delphi technique was used to measure consensus of a panel of expert opinion holders in Scotland. Individuals with key strategic and operational roles in implementing initiatives of pharmacy practice and medicines management were recruited as experts. An electronic questionnaire consisting of 30 statements related to pharmacist prescribing service redesign was developed. These were presented as five-point Likert scales with illustrative quotes. Consensus, defined as 70 % of panel members agreeing (ranked strongly agree/agree) with each statement. Responses were obtained from 35/40 (87.5 %) experts in round one and 29 (72.5 %) in round two. Consensus in round one was achieved for 27/30 of statements relating to aspects of generic 'service development' (e.g. succession planning, multidisciplinary working, quality evaluation, practice development and outcome measures) and 'pharmacist prescribing role development' (e.g. education and future orientation of service). Issues of disagreement were around targeting of pharmacist prescribing to clinical specialities and financial remuneration for prescribing in the hospital setting. Consensus guidance has been developed to facilitate service redesign around hospital pharmacist prescribing.

  2. Responding to the Concerns of Student Cultural Groups: Redesigning Spaces for Cultural Centers

    Science.gov (United States)

    McDowell, Anise Mazone; Higbee, Jeanne L.

    2014-01-01

    This paper describes the engagement of a student committee in redesigning an entire floor of a university union to accommodate student cultural centers and provide space in a fair and equitable manner. The reorganization focused on the process as well as the task of allocating space, with an emphasis on the opportunity to foster the development of…

  3. Case-based reasoning as a technique for knowledge management in business process redesign

    NARCIS (Netherlands)

    Limam Mansar, S.; Reijers, H.A.; Marir, F.

    2003-01-01

    Business Process Redesign (BPR) helps rethinking a process in order to enhance its performance. Practitioners have been developing methodologies to support BPR implementation. However, most methodologies lack actual guidance on deriving a process design threatening the success of BPR. In this paper,

  4. Which kind of knowledge is suitable for redesigning hospital logistic processes?

    NARCIS (Netherlands)

    Maruster, L; Jorna, RJ; Miksch, S; Hunter, J; Keravnou, E

    2005-01-01

    A knowledge management perspective is rarely used to model a process. Using the cognitive perspective on knowledge management in which we start our analysis with events and knowledge (bottom-up) instead of with processes and units (top-down), we propose a new approach for redesigning hospital

  5. Redesigning Romance: The Making and Analysis of a Critical Literacy Comic in South Africa.

    Science.gov (United States)

    Shariff, Patricia Watson; Janks, Hilary

    2001-01-01

    Examines the making and redesigning of the romance stories (in comic-book form) in drama in education workshops conducted in a rural South African high school. Brings together practice and theory that were independently conceived, so that they can mutually inform one another. Analyses the narrative outline which kick-started the comic development…

  6. Application of Evidence-Centered Assessment Design to the Advanced Placement Redesign: A Graphic Restatement

    Science.gov (United States)

    Bejar, Isaac I.

    2010-01-01

    The foregoing articles constitute what I consider a comprehensive and clear description of the redesign process of a major assessment. The articles serve to illustrate the problems that will need to be addressed by large-scale assessments in the twenty-first century. Primary among them is how to organize the development of such assessments to meet…

  7. Strategies for Aligning Physicians to System Redesign Goals at Eight Safety-Net Systems.

    Science.gov (United States)

    Zallman, Leah; Bearse, Adriana; Neal, Natasha; VanDeusen Lukas, Carol; Hacker, Karen

    2014-12-01

    Facing recent economic and regulatory pressures, safety-net systems (SNSs) are redesigning their organizations to improve care delivery, remain financially viable, and maintain competitive positions. Aligning physicians with redesign goals is a priority, particularly as many SNSs shift toward patient-centered, population health-focused models. No previous work has examined efforts to align physicians to safety net redesign efforts. This qualitative study, conducted at eight SNSs, examined challenges faced in a changing health care environment, as well as strategies and resources to address them. Strategies clustered in two categories: physician role definition and organizational infrastructure. Physician role definition strategies were (1) changing payment and employment arrangements, (2) changing clinical roles, (3) increasing physician involvement in quality improvement, and (4) strengthening physician leadership in clinical and quality roles. Organizational infrastructure strategies were (1) ensuring medical center leadership support and integration, (2) utilizing data to drive physician behavior, and (3) addressing competing allegiances with academia. All sites reported multifaceted approaches but differed in specific strategies employed, facilitators noted, and challenges encountered. The findings highlight the need to implement multiple strategies to align physicians in redesign efforts. They suggest that all health systems, whether SNSs or not, can capitalize on qualities of physicians and existing infrastructural and leadership elements to achieve physician alignment. However, they must contend with and address challenges of competing allegiance (for example, academic, physician organization, hospital), as well as resistance to changing clinical roles and payment structures.

  8. Simulation modelling for food supply chain redesign; integrated decision making on product quality, sustainability and logistics

    NARCIS (Netherlands)

    van der Vorst, J.G.A.J.; Tromp, S.O.; van der Zee, D.J.

    2009-01-01

    Food supply chains are confronted with increased consumer demands on food quality and sustainability. When redesigning these chains the analysis of food quality change and environmental load of new scenarios is as important as the analysis of efficiency and responsiveness requirements. Simulation

  9. Redesigning the work system of rubber industries based on total ergonomics and ergo-micmac integration

    Science.gov (United States)

    Setiawan, H.

    2018-01-01

    The factory capacity achievement and the bottleneck reduction of production process at wet-blanket workstations are influenced by the balance of life quality rates and worker’s productivity, along with the worker’s ability and limitations, tasks, organization and work environment. The life quality of workers is indicated by: the reduction of workload, and fatigue. Meanwhile, work productivity is measured by increasing production results per work shift. The optimization of the quality of life and productivity of workers is achieved by redesigning the system and workstations based on ergonomics integrating Total Ergonomics with Ergo-MicMac (Micro Ergonomics and Macro Ergonomics), which includes redesigning wet-blanket folding worktable, regulating the system pattern of working in pairs, giving official break time, giving extra nutritious intakes such as sweet tea and snack Pempek, giving personal protective equipments, and redesigning physical working environments.This study was an experimental study, with treatment by subject design involving 30 workers sampled at a workstation condition before and after Ergonomics based redesign. The findings and conclusions of the study were derived from the reduction of the workload by 16.06%, fatigue by 18.84% and the increase of production results per work shift by 20.29%.

  10. A Product Analysis Method and Its Staging to Develop Redesign Competences

    Science.gov (United States)

    Hansen, Claus Thorp; Lenau, Torben Anker

    2013-01-01

    Most product development work in industrial practice is incremental, i.e., the company has had a product in production and on the market for some time, and now time has come to design an upgraded variant. This type of redesign project requires that the engineering designers have competences to carry through an analysis of the existing product…

  11. Applying cognitive load theory to the redesign of a conventional database systems course

    Science.gov (United States)

    Mason, Raina; Seton, Carolyn; Cooper, Graham

    2016-01-01

    Cognitive load theory (CLT) was used to redesign a Database Systems course for Information Technology students. The redesign was intended to address poor student performance and low satisfaction, and to provide a more relevant foundation in database design and use for subsequent studies and industry. The original course followed the conventional structure for a database course, covering database design first, then database development. Analysis showed the conventional course content was appropriate but the instructional materials used were too complex, especially for novice students. The redesign of instructional materials applied CLT to remove split attention and redundancy effects, to provide suitable worked examples and sub-goals, and included an extensive re-sequencing of content. The approach was primarily directed towards mid- to lower performing students and results showed a significant improvement for this cohort with the exam failure rate reducing by 34% after the redesign on identical final exams. Student satisfaction also increased and feedback from subsequent study was very positive. The application of CLT to the design of instructional materials is discussed for delivery of technical courses.

  12. Creative thinking of design and redesign on SEAT aircraft cabin testbed: a case study

    NARCIS (Netherlands)

    Tan, C.F.; Chen, W.; Rauterberg, G.W.M.

    2009-01-01

    this paper, the intuition approach in the design and redesign of the environmental friendly innovative aircraft cabin simulator is presented.. The aircraft cabin simulator is a testbed that used for European Project SEAT (Smart tEchnologies for Stress free Air Travel). The SEAT project aims to

  13. Business process redesign in healthcare : towards an evidence-based holistic approach

    NARCIS (Netherlands)

    Vanwersch, R.J.B.; Mans, R.S.; Reijers, H.A.; Shiharzi, A.

    2012-01-01

    The redesign of business processes has become the key challenge for many healthcare organizations. This paper argues that current main research streams fail to assist healthcare practitioners in facing this challenge. More specifically, the main research streams fail to support practitioners in

  14. Redesigning business processes : a methodology based on simulation and process mining techniques

    NARCIS (Netherlands)

    Maruster, L.; van Beest, N.R.T.P.

    2009-01-01

    Nowadays, organizations have to adjust their business processes along with the changing environment in order to maintain a competitive advantage. Changing a part of the system to support the business process implies changing the entire system, which leads to complex redesign activities. In this

  15. Effects of a Redesigned Classroom on Play Behaviour among Preschool Children

    Science.gov (United States)

    Acer, Dilek; Gözen, Göksu; Firat, Zehra Saadet; Kefeli, Hatice; Aslan, Büsra

    2016-01-01

    Current research exists regarding the play behaviour of students in various settings and with varying abilities. Regardless, there needs to be improved understanding of how students' play behaviour is affected when their classroom environment is significantly redesigned. This study examined, over a 21-week period between December 2013 and May…

  16. Intuitive thinking of design and redesign on innovative aircraft cabin simulator

    NARCIS (Netherlands)

    Tan, C.F.; Chen, W.; Rauterberg, G.W.M.

    2009-01-01

    In this paper, the intuition approach in the design and redesign of the environmental friendly innovative aircraft cabin simulator is presented. The simulator is a testbed that was designed and built for research on aircraft passenger comfort improvement of long haul air travel. The simulation

  17. Performance-Based Task Assessment of Higher-Order Proficiencies in Redesigned STEM High Schools

    Science.gov (United States)

    Ernst, Jeremy V.; Glennie, Elizabeth; Li, Songze

    2017-01-01

    This study explored student abilities in applying conceptual knowledge when presented with structured performance tasks. Specifically, the study gauged proficiency in higher-order applications of students enrolled in earth and environmental science or biology. The student sample was drawn from a Redesigned STEM high school model where a tested…

  18. Supporting the full BPM life-cycle using process mining and intelligent redesign

    NARCIS (Netherlands)

    Netjes, M.; Reijers, H.A.; Aalst, van der W.M.P.; Siau, K.

    2007-01-01

    Abstract. Business Process Management (BPM) systems provide a broad range of facilities to enact and manage operational business processes. Ideally, these systems should provide support for the complete BPM life-cycle: (re)design, configuration, execution, control, and diagnosis by the FileNet P8

  19. 77 FR 56859 - Federal Register Notification of Redesignation of Potential Wilderness as Wilderness, Ross Lake...

    Science.gov (United States)

    2012-09-14

    ... Register Notification of Redesignation of Potential Wilderness as Wilderness, Ross Lake National Recreation..., Ross Lake National Recreation Area, and Lake Chelan National Recreation Area as the Stephen Mather... acres of potential wilderness within Ross Lake National Recreation Area, including approximately 1,667...

  20. Using business process redesign to reduce wait times at a university hospital in the Netherlands

    NARCIS (Netherlands)

    Elkhuizen, Sylvia G.; Burger, Matthe P. M.; Jonkers, Rene E.; Limburg, Martien; Klazinga, Niek; Bakker, Piet J. M.

    2007-01-01

    BACKGROUND: Business process redesign (BPR) has been applied to implement more customer-focused and cost-effective care. In 2002, two pilot projects to improve patient care processes for two specific patient groups were conducted at the Academic Medical Center, a 1,000-bed university hospital in

  1. Using business process redesign to reduce wait times at a university hospital in the Netherlands.

    Science.gov (United States)

    Elkhuizen, Sylvia G; Burger, Matthe P M; Jonkers, Rene E; Limburg, Martien; Klazinga, Niek; Bakker, Piet J M

    2007-06-01

    Business process redesign (BPR) has been applied to implement more customer-focused and cost-effective care. In 2002, two pilot projects to improve patient care processes for two specific patient groups were conducted at the Academic Medical Center, a 1,000-bed university hospital in Amsterdam. The BPR consisted of process analysis, identification of bottlenecks and goals for redesign, selection of interventions, and evaluation of effects. After identifying and selecting interventions with the greatest expected benefits, changes were implemented and effects were evaluated. For gynecologic oncology patients, access time (from telephone call to first visit) was reduced from 14 days to changes in communication and planning were sufficient to eliminate bottlenecks in the gynecologic oncology project, the dyspnea project required a radical redesign of processes. Experience since these projects suggests that process redesign may have only marginal impact when the greatest bottleneck occurs, as was the case for the two BPR projects, at the point of access to central diagnostic facilities.

  2. The Power of Professionally Situated Practice Analysis in Redesigning Organisations: A Psychosociological Approach

    Science.gov (United States)

    Scaratti, Giuseppe; Gorli, Mara; Ripamonti, Silvio

    2009-01-01

    Purpose: This paper seeks to provoke thoughts around the possibility of using the lever of practices and situated knowledge to trigger organisational change and to redesign it with the involvement of the whole organisation. Design/methodology/approach: The paper presents connections between a psychosociological approach and a practice-based…

  3. Redesigning Schools to Reach Every Student with Excellent Teachers: Financial Planning Summary

    Science.gov (United States)

    Public Impact, 2012

    2012-01-01

    This brief summarizes the ways that schools and their teachers can simultaneously reach more students with excellent teaching, expand teachers' career opportunities, and sustainably fund higher pay and other priorities. This is based on Public Impact's school models that use job redesign and technology to extend the reach of excellent teachers to…

  4. A Behavioral Analysis of the Laboratory Learning Process: Redesigning a Teaching Unit on Recrystallization.

    Science.gov (United States)

    Mulder, T.; Verdonk, A. H.

    1984-01-01

    Reports on a project in which observations of student and teaching assistant behavior were used to redesign a teaching unit on recrystallization. Comments on the instruction manual, starting points for teaching the unit, and list of objectives with related tasks are included. (JN)

  5. The Power of Structural and Symbolic Redesign: Creating a Collaborative Learning Community in Higher Education.

    Science.gov (United States)

    Geltner, Beverley B.

    This paper describes efforts to redesign a graduate program of educational administration and leadership at Oakland University in Rochester, Michigan, shaped by contributions of researchers in contemporary management and leadership theory, feminist pedagogy, action research, and educational reform. A culture of collaboration, inclusion, and…

  6. 78 FR 48087 - Approval and Promulgation of Air Quality Implementation Plans; Ohio; Redesignation of the Canton...

    Science.gov (United States)

    2013-08-07

    ... specific examples to illustrate your concerns, and suggest alternatives. 7. Explain your views as clearly... 172(c)(9) contingency measures is not applicable for purposes of redesignation. Id. Section 172(c)(3... area demonstrates maintenance of the NAAQS without part D NSR. A detailed rationale for this view is...

  7. Re-Designing University Courses to Support Collaborative Knowledge Creation Practices

    Science.gov (United States)

    Lakkala, Minna; Toom, Auli; Ilomäki, Liisa; Muukkkonen, Hanni

    2015-01-01

    Higher education institutions should not only aim to educate academic experts who master their own fields, but also give their students generic skills important in the current society. New teaching methods are required to support the development of such skills. The study examined how a group of voluntary university lecturers re-designed their…

  8. The Delivery of Developmental Mathematics: Course Redesign and Implementation at a Community College

    Science.gov (United States)

    Westerfield, Mary Ann K.

    2013-01-01

    This research was undertaken to determine if the redesigned modular delivery method for developmental mathematics produced a higher sequence completion rate within a year as compared to the traditional lecture style delivery. Re-enrollment rates from fall to spring for the modularized delivery system were compared to the traditional delivery…

  9. Service-Learning and Integrated Course Redesign: Principles of Management and the Campus Kitchen Metaproject

    Science.gov (United States)

    Flannery, Brenda L.; Pragman, Claudia H.

    2010-01-01

    This article describes the process of redesigning a Principles of Management course to integrate a service-learning metaproject. The metaproject was Campus Kitchen, a food recovery and delivery program operated on a handful of university campuses across the United States. We used L. Dee Fink's integrated course design approach as well as systems…

  10. Power production with direct energy conversion

    Energy Technology Data Exchange (ETDEWEB)

    Rochau, G.; Lipinski, R.; Polansky, G.; Seidel, D.; Slutz, S. [Sandia National Labs., Albuquerque, NM (United States); Morrow, C. [Morrow Consulting, Albuquerque, NM (United States); Anghaie, S. [Florida Univ., Gainesville, FL (United States); Beller, D. [Los Alamos National Lab., NM (United States); Brown, L. [General Atomic Co., San Diego, CA (United States); Parish, T. [Texas A and M Univ., College Station, TX (United States). Dept. of Nuclear Engineering

    2001-07-01

    The direct energy conversion (DEC) project has as its main goal the development of a direct energy conversion process suitable for commercial development. We define direct energy conversion as any fission process that returns usable energy without using an intermediate thermal process. During the first phase of study, nine different concepts were investigated and 3 were selected: 1) quasi-spherical magnetically insulated fission electrode cell, 2) fission fragment magnetic collimator, and 3) gaseous core reactor with MHD generator. Selection was based on efficiency and feasibility. The realization of their potential requires an investment in both technically and commercially oriented research. The DEC project has a process in place to take one of these concepts forward and to outline the road map for further development. (A.C.)

  11. Power production with direct energy conversion

    International Nuclear Information System (INIS)

    Rochau, G.; Lipinski, R.; Polansky, G.; Seidel, D.; Slutz, S.; Morrow, C.; Anghaie, S.; Beller, D.; Brown, L.; Parish, T.

    2001-01-01

    The direct energy conversion (DEC) project has as its main goal the development of a direct energy conversion process suitable for commercial development. We define direct energy conversion as any fission process that returns usable energy without using an intermediate thermal process. During the first phase of study, nine different concepts were investigated and 3 were selected: 1) quasi-spherical magnetically insulated fission electrode cell, 2) fission fragment magnetic collimator, and 3) gaseous core reactor with MHD generator. Selection was based on efficiency and feasibility. The realization of their potential requires an investment in both technically and commercially oriented research. The DEC project has a process in place to take one of these concepts forward and to outline the road map for further development. (A.C.)

  12. Conversion of Semipalatinsk test site

    International Nuclear Information System (INIS)

    Cherepnin, Yu. S.

    1997-01-01

    The conversion of the former defense enterprises of STS (Semipalatinsk Test Sate) started under very difficult conditions, when not only research and production activity, but all social life of Kurchatov city were conversed which was caused by a fast curtailment and restationing of Russian military units from the test site. A real risk of a complete destruction of the whole research and production structure of the city existed. From this point of view, the decision of the Republic of Kazakhstan Government to create the National Nuclear Center on the base of the test site research enterprises was actual and timely. During 1993, three research institutes of NNC RK - Institute of Atomic Energy, Institute of Geophysics Research and Institute of Radiation Safety and Environment were established. This decision, under conditions of the Ussr disintegration and liquidation of the test site military divisions, allowed to preserve the qualified personnel, to provide and follow-up the operation of nuclear dangerous facilities, to develop and start the realization of the full scale conversion program.At present time, directions and structure of basic research work in NNC RK are as follows: - liquidation of nuclear explosions consequences; - liquidation of technological infrastructure used for preparation and conduction of nuclear weapon testing; - creation of technology, equipment and places for acceptance and storage of radioactive wastes; - working out of atomic energy development conception in Kazakhstan; - study of reactor core melt behavior under severe accidents in NPP; - development of methods and means of nuclear testing detection, continuous monitoring of nuclear explosions; - experimental work on a study of structure materials behavior of ITER thermonuclear reactor; - creation of industries requiring a lage implementation of science

  13. Uranium conversion; Urankonvertering

    Energy Technology Data Exchange (ETDEWEB)

    Oliver, Lena; Peterson, Jenny; Wilhelmsen, Katarina [Swedish Defence Research Agency (FOI), Stockholm (Sweden)

    2006-03-15

    FOI, has performed a study on uranium conversion processes that are of importance in the production of different uranium compounds in the nuclear industry. The same conversion processes are of interest both when production of nuclear fuel and production of fissile material for nuclear weapons are considered. Countries that have nuclear weapons ambitions, with the intention to produce highly enriched uranium for weapons purposes, need some degree of uranium conversion capability depending on the uranium feed material available. This report describes the processes that are needed from uranium mining and milling to the different conversion processes for converting uranium ore concentrate to uranium hexafluoride. Uranium hexafluoride is the uranium compound used in most enrichment facilities. The processes needed to produce uranium dioxide for use in nuclear fuel and the processes needed to convert different uranium compounds to uranium metal - the form of uranium that is used in a nuclear weapon - are also presented. The production of uranium ore concentrate from uranium ore is included since uranium ore concentrate is the feed material required for a uranium conversion facility. Both the chemistry and principles or the different uranium conversion processes and the equipment needed in the processes are described. Since most of the equipment that is used in a uranium conversion facility is similar to that used in conventional chemical industry, it is difficult to determine if certain equipment is considered for uranium conversion or not. However, the chemical conversion processes where UF{sub 6} and UF{sub 4} are present require equipment that is made of corrosion resistant material.

  14. Redesigning a clinical mentoring program for improved outcomes in the clinical training of clerks

    Directory of Open Access Journals (Sweden)

    Chia-Der Lin

    2015-09-01

    Full Text Available Introduction: Mentorship has been noted as critical to medical students adapting to clinical training in the medical workplace. A lack of infrastructure in a mentoring program might deter relationship building between mentors and mentees. This study assessed the effect of a redesigned clinical mentoring program from the perspective of clerks. The objective was to assess the benefits of the redesigned program and identify potential improvements. Methods: A redesigned clinical mentoring program was launched in a medical center according to previous theoretical and practical studies on clinical training workplaces, including the elements of mentor qualifications, positive and active enhancers for mentor–mentee relationship building, the timing of mentoring performance evaluation, and financial and professional incentives. A four-wave web survey was conducted, comprising one evaluation of the former mentoring program and three evaluations of the redesigned clinical mentoring program. Sixty-four fifth-year medical students in clerkships who responded to the first wave and to at least two of the three following waves were included in the study. A structured and validated questionnaire encompassing 15 items on mentor performance and the personal characteristics of the clerks was used. Mixed linear models were developed for repeated measurements and to adjust for personal characteristics. Results: The results revealed that the redesigned mentoring program improved the mentors’ performance over time for most evaluated items regarding professional development and personal support provided to the mentees. Conclusions: Our findings serve as an improved framework for the role of the institution and demonstrate how institutional policies, programs, and structures can shape a clinical mentoring program. We recommend the adoption of mentorship schemes for other cohorts of medical students and for different learning and training stages involved in becoming a

  15. Redesigning a clinical mentoring program for improved outcomes in the clinical training of clerks

    Science.gov (United States)

    Lin, Chia-Der; Lin, Blossom Yen-Ju; Lin, Cheng-Chieh; Lee, Cheng-Chun

    2015-01-01

    Introduction Mentorship has been noted as critical to medical students adapting to clinical training in the medical workplace. A lack of infrastructure in a mentoring program might deter relationship building between mentors and mentees. This study assessed the effect of a redesigned clinical mentoring program from the perspective of clerks. The objective was to assess the benefits of the redesigned program and identify potential improvements. Methods A redesigned clinical mentoring program was launched in a medical center according to previous theoretical and practical studies on clinical training workplaces, including the elements of mentor qualifications, positive and active enhancers for mentor–mentee relationship building, the timing of mentoring performance evaluation, and financial and professional incentives. A four-wave web survey was conducted, comprising one evaluation of the former mentoring program and three evaluations of the redesigned clinical mentoring program. Sixty-four fifth-year medical students in clerkships who responded to the first wave and to at least two of the three following waves were included in the study. A structured and validated questionnaire encompassing 15 items on mentor performance and the personal characteristics of the clerks was used. Mixed linear models were developed for repeated measurements and to adjust for personal characteristics. Results The results revealed that the redesigned mentoring program improved the mentors’ performance over time for most evaluated items regarding professional development and personal support provided to the mentees. Conclusions Our findings serve as an improved framework for the role of the institution and demonstrate how institutional policies, programs, and structures can shape a clinical mentoring program. We recommend the adoption of mentorship schemes for other cohorts of medical students and for different learning and training stages involved in becoming a physician. PMID

  16. Solar energy conversion systems

    CERN Document Server

    Brownson, Jeffrey R S

    2013-01-01

    Solar energy conversion requires a different mind-set from traditional energy engineering in order to assess distribution, scales of use, systems design, predictive economic models for fluctuating solar resources, and planning to address transient cycles and social adoption. Solar Energy Conversion Systems examines solar energy conversion as an integrative design process, applying systems thinking methods to a solid knowledge base for creators of solar energy systems. This approach permits different levels of access for the emerging broad audience of scientists, engineers, architects, planners

  17. Energy conversion statics

    CERN Document Server

    Messerle, H K; Declaris, Nicholas

    2013-01-01

    Energy Conversion Statics deals with equilibrium situations and processes linking equilibrium states. A development of the basic theory of energy conversion statics and its applications is presented. In the applications the emphasis is on processes involving electrical energy. The text commences by introducing the general concept of energy with a survey of primary and secondary energy forms, their availability, and use. The second chapter presents the basic laws of energy conversion. Four postulates defining the overall range of applicability of the general theory are set out, demonstrating th

  18. Uranium Conversion & Enrichment

    Energy Technology Data Exchange (ETDEWEB)

    Karpius, Peter Joseph [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-02-06

    The isotopes of uranium that are found in nature, and hence in ‘fresh’ Yellowcake’, are not in relative proportions that are suitable for power or weapons applications. The goal of conversion then is to transform the U3O8 yellowcake into UF6. Conversion and enrichment of uranium is usually required to obtain material with enough 235U to be usable as fuel in a reactor or weapon. The cost, size, and complexity of practical conversion and enrichment facilities aid in nonproliferation by design.

  19. Postoperative conversion disorder.

    Science.gov (United States)

    Afolabi, Kola; Ali, Sameer; Gahtan, Vivian; Gorji, Reza; Li, Fenghua; Nussmeier, Nancy A

    2016-05-01

    Conversion disorder is a psychiatric disorder in which psychological stress causes neurologic deficits. A 28-year-old female surgical patient had uneventful general anesthesia and emergence but developed conversion disorder 1 hour postoperatively. She reported difficulty speaking, right-hand numbness and weakness, and right-leg paralysis. Neurologic examination and imaging revealed no neuronal damage, herniation, hemorrhage, or stroke. The patient mentioned failing examinations the day before surgery and discontinuing her prescribed antidepressant medication, leading us to diagnose conversion disorder, with eventual confirmation by neuroimaging and follow-up examinations. Copyright © 2016 Elsevier Inc. All rights reserved.

  20. Uranium conversion wastes

    International Nuclear Information System (INIS)

    Vicente, R.; Dellamano, J.C.

    1989-12-01

    A set of mathematical equations was developed and used to estimate the radiological significance of each radionuclide potentially present in the uranium refining industry effluents. The equations described the evolution in time of the radionuclides activities in the uranium fuel cycle, from mining and milling, through the yellowcake, till the conversion effluents. Some radionuclides that are not usually monitored in conversion effluents (e.g. Pa-231 and Ac-227) were found to be potentially relevant from the radiological point of view in conversion facilities, and are certainly relevant in mining and milling industry, at least in a few waste streams. (author) [pt

  1. NASA thermionic-conversion program

    International Nuclear Information System (INIS)

    Morris, J.F.

    1977-01-01

    NASA's program for applied research and technology (ART) in thermionic energy conversion (TEC) has made worthwhile contributions in a relatively short time: Many of these accomplishments are incremental, yet important. And their integration has yielded gains in performance as well as in the knowledge necessary to point productive directions for future work. Both promise and problems derive from the degrees of freedom allowed by the current programmatic emphasis on out-of-core thermionics. Materials and designs previously prohibited by in-core nucleonics and geometries now offer new potentialities. But as a result a major TEC-ART responsibility is the efficient reduction of the glitter of diverse possibilities to the hard glint of reality. As always high-temperature material effects are crucial to the level and duration of TEC performance: New electrodes must increase and maintain power output regardless of emitter-vapor deposition on collectors. They must also serve compatibly with hot-shell alloys. And while space TEC must face high-temperature vaporization problems externally as well as internally, terrestrial TEC must tolerate hot corrosive atmospheres outside and near-vacuum inside. Furthermore, some modes for decreasing interelectrode losses appear to require rather demanding converter geometries to produce practical power densities. In these areas and others significant progress is being made in the NASA TEC-ART Program

  2. Redesigning Journal Clubs to Staying Current with the Literature.

    Science.gov (United States)

    Dickerson, Roland N; Wood, G Christopher; Swanson, Joseph M; Brown, Rex O

    2017-11-06

    Staying current with the literature is of paramount importance to the pharmacist engaged in an evidence-based clinical practice. Given the expanding roles and responsibilities of today's pharmacists combined with exponential growth in new medical and health sciences literature, staying current has become an extremely daunting task. Traditional journal clubs have focused upon their role as a training vehicle for teaching critical reading skills to residents. However, schools of pharmacy are now required to provide instruction in biostatistics, research design, and interpretation. We present a paradigm shift in the traditional journal club model whereby a collection of periodicals is screened and a short synopsis of the pertinent articles is provided. The associated tasks for screening and presenting of the primary literature are shared among a group of clinicians and trainees with similar practice interests resulting in a more reasonable workload for the individual. This journal club method was effective in identifying a significant majority of articles judged to be pertinent by independent groups of clinicians in the same practice arenas. Details regarding the shared core practice and knowledge base elements, journal club format, identification of journals, and evaluation of the success of the journal club technique are provided.

  3. Mining Conversational Social Video

    OpenAIRE

    Biel, Joan-Isaac

    2013-01-01

    The ubiquity of social media in our daily life, the intense user participation, and the explo- sion of multimedia content have generated an extraordinary interest from computer and social scientists to investigate the traces left by users to understand human behavior online. From this perspective, YouTube can be seen as the largest collection of audiovisual human behavioral data, among which conversational video blogs (vlogs) are one of the basic formats. Conversational vlogs have evolved fro...

  4. Persuasion detection in conversation

    OpenAIRE

    Gilbert, Henry T.

    2010-01-01

    Approved for public release; distribution is unlimited In this thesis, we present a system for annotating persuasion in conversation based on a social-psychological model. We augmented the social model developed by James Cialdini with some of our own categories for annotators to label. The conversations consisted of 37 hostage negotiation transcripts from private and public sources, with all personal information removed from the private source transcripts. We evaluated the level of agre...

  5. Perspective on direct conversion

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, W B

    1963-10-15

    The objective of direct conversion is high electrical output for minimum total cost, and not always high conversion efficiency. The wide range of techniques embracing cryogenics and hot plasma derives from the special requirements of source, environment, and application. Sources include solar and other radiation, nuclear fission and fusion, chemical energy, and heat. Environments and applications range from space vehicles to submarines and from giant power networks to isolated buoys and pocket devices. (auth)

  6. Conversational flow promotes solidarity.

    Science.gov (United States)

    Koudenburg, Namkje; Postmes, Tom; Gordijn, Ernestine H

    2013-01-01

    Social interaction is fundamental to the development of various aspects of "we-ness". Previous research has focused on the role the content of interaction plays in establishing feelings of unity, belongingness and shared reality (a cluster of variables referred to as solidarity here). The present paper is less concerned with content, but focuses on the form of social interaction. We propose that the degree to which conversations flow smoothly or not is, of itself, a cue to solidarity. We test this hypothesis in samples of unacquainted and acquainted dyads who communicate via headsets. Conversational flow is disrupted by introducing a delay in the auditory feedback (vs. no delay). Results of three studies show that smoothly coordinated conversations (compared with disrupted conversations and a control condition) increase feelings of belonging and perceptions of group entitativity, independently of conversation content. These effects are driven by the subjective experience of conversational flow. Our data suggest that this process occurs largely beyond individuals' control. We conclude that the form of social interaction is a powerful cue for inferring group solidarity. Implications for the impact of modern communication technology on developing a shared social identity are discussed.

  7. Conversational flow promotes solidarity.

    Directory of Open Access Journals (Sweden)

    Namkje Koudenburg

    Full Text Available Social interaction is fundamental to the development of various aspects of "we-ness". Previous research has focused on the role the content of interaction plays in establishing feelings of unity, belongingness and shared reality (a cluster of variables referred to as solidarity here. The present paper is less concerned with content, but focuses on the form of social interaction. We propose that the degree to which conversations flow smoothly or not is, of itself, a cue to solidarity. We test this hypothesis in samples of unacquainted and acquainted dyads who communicate via headsets. Conversational flow is disrupted by introducing a delay in the auditory feedback (vs. no delay. Results of three studies show that smoothly coordinated conversations (compared with disrupted conversations and a control condition increase feelings of belonging and perceptions of group entitativity, independently of conversation content. These effects are driven by the subjective experience of conversational flow. Our data suggest that this process occurs largely beyond individuals' control. We conclude that the form of social interaction is a powerful cue for inferring group solidarity. Implications for the impact of modern communication technology on developing a shared social identity are discussed.

  8. Feasibility of using gadolinium as a burnable poison in PWR cores. Final report

    International Nuclear Information System (INIS)

    Rothleder, B.M.

    1981-02-01

    As an alternative to the use of lumped burnable absorbers in PWR cores, distributed burnable absorbers are being considered for generic application. These burnable absorbers take the form of Gd 2 O 3 mixed with UO 2 in selected fuel rods (as is currently done in BWR cores). The work discussed herein concerns a three-dimensional feasibility study of the use of such distributed burnable absorbers in PWR cores. This study of distributed burnable absorbers was performed for the first cycle of a typical current design PWR using the following steps: analysis of a generic reference core design; determination of gadolinium assembly designs; determination of a generic gadolinium core design; evaluation of feasibility by examining selected parameters; and redesign of the generic gadolinium core, using axial zoning

  9. Kinetics of Scheelite Conversion in Sulfuric Acid

    Science.gov (United States)

    Shen, Leiting; Li, Xiaobin; Zhou, Qiusheng; Peng, Zhihong; Liu, Guihua; Qi, Tiangui; Taskinen, Pekka

    2018-02-01

    Complete conversion of scheelite in H2SO4 solution plays a key role in exploration of cleaner technology for producing ammonium paratungstate. In this work, the factors influencing scheelite conversion were investigated experimentally to model its kinetics. The results indicated that the conversion rate increases with increasing temperature and reducing particle size, but is almost independent of stirring speed. Moreover, although the conversion rate increases with increasing initial H2SO4 concentration (≤ 1.25 mol/L), it decreases rapidly at 1.5 mol/L H2SO4 after 10 min due to formation of a H2WO4 layer. The experimental data agree quite well with the shrinking core model under chemical reaction control in ≤ 1.25 mol/L H2SO4 solution, and the kinetic equation was established as: 1- ( 1- α )^{ 1 / 3} = 2 2 2 5 4 6. 6\\cdot C_{{{H}_{ 2} {SO}_{ 4} }}^{ 1. 2 2 6} \\cdot r_{ 0}^{ - 1} \\cdot e^{{ - 3 9 2 6 0/RT}} \\cdot t (t, min). This work could contribute to better understanding of scheelite conversion in H2SO4 solution and development of a new route for ammonium paratungstate production.

  10. Overheating preventive system for reactor core fuels

    International Nuclear Information System (INIS)

    Ito, Daiju

    1981-01-01

    Purpose: To ensure the cooling function of reactor water in a cooling system in case of erroneous indication or misoperation by reliable temperature measurement for fuels and actuating relays through the conversion output obtained therefrom. Constitution: Thermometers are disposed laterally and vertically in a reactor core in contact with core fuels so as to correspond to the change of status in the reactor core. When there is a high temperature signal issued from one of the thermometers or one of conversion circuits, the function of relay contacts does not provide the closed state as a whole. When high temperature signals are issued from two or more thermometers of conversion circuits from independent OR circuits, the function of the relay contacts provides the closure state as a whole. Consequently, in the use of 2-out of 3-circuits, the entire closure state, that is, the misoperation of the relay contacts for the thermometer or the conversion circuits can be avoided. In this way, by the application of the output from the conversion circuits to the logic circuit and, in turn, application of the output therefrom to the relay groups in 2-out of 3-constitution, the reactor safety can be improved. (Horiuchi, T.)

  11. HEU/LEU-conversion of BER II successfully finished

    International Nuclear Information System (INIS)

    Haas, K.; Fischer, C.-O.; Krohn, H.

    2000-01-01

    The BER II (Berliner Experimental Reactor) research reactor is a swimming pool type reactor located in Berlin, Germany. The reactor operates with a thermal power of 10 MW and is primarily used to produce neutrons for neutron scattering experiments. The conversion from HEU- to LEU-fuel elements began in August, 1997. At the last RERTR Meeting 1999 in Budapest, Hungary, Hahn-Meitner-Institut (HMI) presented a 'Status Report' on the conversion of 10 HEU/LEU mixed cores. In February 2000, HMI finished the HEU/LEU-conversion. Hereby, the first pure LEU-standard-core went into operation. Our second LEU-core just ends its operation at the end of July. The third LEU-core will be built up in the beginning of August. The average burn-up rate was improved from 50 - 55% (HEU) to 60 - 65% (LEU). Therefore, only 14 elements/year are now used instead of 28/year. The following report describes our first steps in building pure LEU-cores from mixed HEU/LEU-cores, as well as our initial experience using the pure LEU-cores. (author)

  12. A redesigned follitropin alfa pen injector for infertility: results of a market research study

    Directory of Open Access Journals (Sweden)

    Abbotts C

    2011-06-01

    Full Text Available Carole Abbotts1, Cristiana Salgado-Braga2, Céline Audibert-Gros31Pharmaceutical Marketing Research Consultancy, London, UK; 2Fertility and Endocrinology Global Business Unit, 3Business Intelligence, Merck Serono SA, Geneva, SwitzerlandBackground: The purpose of this study was to evaluate patient-learning and nurse-teaching experiences when using a redesigned prefilled, ready-to-use follitropin alfa pen injector.Methods: Seventy-three UK women of reproductive age either administering daily treatment with self-injectable gonadotropins or about to start gonadotropin treatment for infertility (aged 24–47 years; 53 self-injection-experienced and 20 self-injection-naïve and 28 nurses from UK infertility clinics were recruited for the study. Following instruction, patients and nurses used the redesigned follitropin alfa pen to inject water into an orange and completed questionnaires to evaluate their experiences with the pen immediately after the simulated injections.Results: Most (88%, n = 64 patients found it easy to learn how to use the pen. Among injection-experienced patients, 66% (n = 35 agreed that the redesigned pen was easier to learn to use compared with their current method and 70% (n = 37 also said they would prefer its use over current devices for all injectable fertility medications. All nurses considered the redesigned pen easy to learn and believed it would be easy to teach patients how to use. Eighty-six percent (n = 24 of the nurses thought it was easy to teach patients to determine the remaining dose to be dialed and injected in a second pen if the initial dose was incomplete. Compared with other injection devices, 96% (n = 27 thought it was "much easier" to "as easy" to teach patients to use the redesigned pen. Based on ease of teaching, 68% (n = 19 of nurses would choose to teach the pen in preference to any other injection method. Almost all (93%, n = 26 nurses considered that having the same pen format for a range of

  13. Side core lifter

    Energy Technology Data Exchange (ETDEWEB)

    Edelman, Ya A

    1982-01-01

    A side core lifter is proposed which contains a housing with guide slits and a removable core lifter with side projections on the support section connected to the core receiver. In order to preserve the structure of the rock in the core sample by means of guaranteeing rectilinear movement of the core lifter in the rock, the support and core receiver sections are hinged. The device is equipped with a spring for angular shift in the core-reception part.

  14. Redesigning Introductory Science Courses to Teach Sustainability: Introducing the L(SC)2 Paradigm

    Science.gov (United States)

    Myers, J. D.; Campbell-Stone, E.; Massey, G.

    2008-12-01

    Modern societies consume vast quantities of Earth resources at unsustainable levels; at the same time, resource extraction, processing, production, use and disposal have resulted in environmental damage severe enough to threaten the life-support systems of our planet. These threats are produced by multiple, integrative and cumulative environmental stresses, i.e. syndromes, which result from human physical, ecological and social interactions with the environment in specific geographic places. In recent decades, recognition of this growing threat has lead to the concept of sustainability. The science needed to provide the knowledge and know-how for a successful sustainability transition differs markedly from the science that built our modern world. Sustainability science must balanced basic and applied research, promote integrative research focused on specific problems and devise a means of merging fundamental, general scientific principles with understanding of specific places. At the same time, it must use a variety of knowledge areas, i.e. biological systems, Earth systems, technological systems and social systems, to devise solutions to the many complex and difficult problems humankind faces. Clearly, sustainability science is far removed from the discipline-based science taught in most U.S. colleges. Many introductory science courses focus on content, lack context and do not integrate scientific disciplines. To prepare the citizens who will confront future sustainability issues as well as the scientists needed to devise future sustainability strategies, educators and scientists must redesign the typical college science course. A new course paradigm, Literacies and Scientific Content in Social Context (L(SC)2), is ideally suited to teach sustainability science. It offers an alternative approach to liberal science education by redefining and expanding the concept of the interdisciplinary course and merging it with the integrated science course. In addition to

  15. Boiler conversions for biomass

    Energy Technology Data Exchange (ETDEWEB)

    Kinni, J [Tampella Power Inc., Tampere (Finland)

    1997-12-31

    Boiler conversions from grate- and oil-fired boilers to bubbling fluidized bed combustion have been most common in pulp and paper industry. Water treatment sludge combustion, need for additional capacity and tightened emission limits have been the driving forces for the conversion. To accomplish a boiler conversion for biofuel, the lower part of the boiler is replaced with a fluidized bed bottom and new fuel, ash and air systems are added. The Imatran Voima Rauhalahti pulverized-peat-fired boiler was converted to bubbling fluidized bed firing in 1993. In the conversion the boiler capacity was increased by 10 % to 295 MWth and NO{sub x} emissions dropped. In the Kymmene Kuusankoski boiler, the reason for conversion was the combustion of high chlorine content biosludge. The emissions have been under general European limits. During the next years, the emission limits will tighten and the boilers will be designed for most complete combustion and compounds, which can be removed from flue gases, will be taken care of after the boiler. (orig.) 3 refs.

  16. Boiler conversions for biomass

    Energy Technology Data Exchange (ETDEWEB)

    Kinni, J. [Tampella Power Inc., Tampere (Finland)

    1996-12-31

    Boiler conversions from grate- and oil-fired boilers to bubbling fluidized bed combustion have been most common in pulp and paper industry. Water treatment sludge combustion, need for additional capacity and tightened emission limits have been the driving forces for the conversion. To accomplish a boiler conversion for biofuel, the lower part of the boiler is replaced with a fluidized bed bottom and new fuel, ash and air systems are added. The Imatran Voima Rauhalahti pulverized-peat-fired boiler was converted to bubbling fluidized bed firing in 1993. In the conversion the boiler capacity was increased by 10 % to 295 MWth and NO{sub x} emissions dropped. In the Kymmene Kuusankoski boiler, the reason for conversion was the combustion of high chlorine content biosludge. The emissions have been under general European limits. During the next years, the emission limits will tighten and the boilers will be designed for most complete combustion and compounds, which can be removed from flue gases, will be taken care of after the boiler. (orig.) 3 refs.

  17. The Role of the IT Department in Information System and Organizational Redesign.

    Science.gov (United States)

    Stub Petersen, Lone

    2015-01-01

    This paper is based on a qualitative study of IT organization and clinical practice over a period of 3 years supported by additional data during the last 2 years. This paper argues that redesign is central to understanding and developing both healthcare information systems and organizations. The importance of the IT organization is also stressed throughout this paper as a pertinent partner and power when considering organizational change and learning in hospitals as it can serve both as a barrier and a catalyst of change and flexibility in the organization through information systems management. Therefore it is important to consider and secure appropriate forms for redesign and learning in cooperation with the IT department.

  18. Market redesign and regulatory change : how companies doing business in Alberta's power markets will be affected

    International Nuclear Information System (INIS)

    Runge, C.

    2003-01-01

    The Power Pool of Alberta (PPA) began its operations in 1996 based on a model with a single price set based on day ahead offers/bids and real time dispatch. The Electric Utilities Act was amended in 1998 and direct sales were permitted in 1999. The Power Purchase Arrangement Auction was implemented in 2000. Significant events took place in 2001, including: (1) retail competition, (2) PPAs began operations, (3) restrictions on direct sales were removed, (4) forward exchange operation, and (5) ancillary services market. In 2002, the Market Achievement Plan II was implemented and government industry structure was reviewed. There are several considerations regarding market redesign, such as day ahead market, capacity market, congestion management, and Northwest Regional Transmission Organization (RTO West). The role of the International Standard Organization (ISO) was discussed, with reference to the Independent System Operator, Independent Market Operator, and Transmission and Market Planner. Redesign must involve all participants and include informed, phased in changes

  19. Photovoltaic solar energy conversion

    CERN Document Server

    Bauer, Gottfried H

    2015-01-01

    This concise primer on photovoltaic solar energy conversion invites readers to reflect on the conversion of solar light into energy at the most fundamental level and encourages newcomers to the field to help find meaningful answers on how photovoltaic solar energy conversion can work (better), eventually contributing to its ongoing advancement. The book is based on lectures given to graduate students in the Physics Department at the University of Oldenburg over the last two decades, yet also provides an easy-to-follow introduction for doctoral and postdoctoral students from related disciplines such as the materials sciences and electrical engineering. Inspired by classic textbooks in the field, it reflects the author’s own ideas on how to understand, visualize and eventually teach the microscopic physical mechanisms and effects, while keeping the text as concise as possible so as to introduce interested readers to the field and balancing essential knowledge with open questions.

  20. Catalytic Conversion of Carbohydrates

    DEFF Research Database (Denmark)

    Osmundsen, Christian Mårup

    a renewable route to aromatics. The conversion of biomass by high temperature processes is a desirable prospect due to the high volumetric production rates which can be achieved, and the ability of these types of processes to convert a wide range of substrates. Current processes however typically have rather...... with the production of commodity chemicals from the most abundantly available renewable source of carbon, carbohydrates. The production of alkyl lactates by the Lewis acid catalyzed conversion of hexoses is an interesting alternative to current fermentation based processes. A range of stannosilicates were...... to be an efficient initial conversion step in the utilization of biomass for chemicals production. The shift from an oil based chemical industry to one based on renewable resources is bound to happen sooner or later, however the environmental problems associated with the burning of fossil resources means...

  1. Analysis of lifting beam and redesigned lifting lugs for 241-AZ-01A decant pump

    International Nuclear Information System (INIS)

    Coverdell, B.L.

    1994-01-01

    This supporting document details calculations for the proper design of a lifting beam and redesigned lifting lugs for the 241AZO1A decant pump. This design is in accordance with Standard Architectural-Civil Design Criteria, Design Loads for Facilities (DOE-RL 1989) and is safety class three. The design and fabrication is in accordance with American Institute of Steel Construction, Manual of Steel Construction, (AISC, 1989) and the Hanford Hoisting and Rigging Manual (DOE-RL 1993)

  2. Chronic disease management: time for consultant physicians to take more leadership in system redesign.

    Science.gov (United States)

    Brand, C; Scott, I; Greenberg, P; Sargious, P

    2007-09-01

    There is a need for system redesign to meet the needs of individuals with chronic disease. New models of chronic disease care include team-based paradigms that focus on continuous and patient-centred care. In such models the roles of providers and patients must change. In this article we focus on new roles for consultant physicians, as well as barriers and incentives to these roles.

  3. Does a grill menu redesign influence sales, nutrients purchased, and consumer acceptance in a worksite cafeteria?

    Directory of Open Access Journals (Sweden)

    Maya K. Vadiveloo

    2017-12-01

    Full Text Available Worksite cafeterias are compelling venues to improve diet quality through environmental changes.We conducted a pre-post study to evaluate how a cafeteria-initiated grill menu redesign influenced sales, revenue, and nutrient content of foods purchased. Secondly, we evaluated consumer opinions about menu changes to inform practices for worksite environment interventions. Monthly sales data (2012–2015 were used to compute gross sales and revenue of entrées and side dishes pre-post menu changes. Alternative protein sources replaced red meat; nutrient composition and nutrients purchased were compared using Food Pro software. Consumer responses were queried using online surveys; open-ended responses were analyzed using NVivo. Differences in sales and nutrient content pre-post menu redesign were tested with Wilcoxon Rank Sum tests. Gross sales of entrées (61 vs. 222servings/month; p=0.01 and side dishes (120 vs. 365servings/month; p=0.001 increased more than three-fold post-menu changes. Revenue from entrées (312 vs. 1144USD/month; p=0.01 and side dishes (238 vs. 914USD/month; p=0.001 also increased; per entrée, consumers purchased significantly more unsaturated fat (5g, and less saturated fat (3g and sodium (100mg. For side dishes, they purchased fewer calories (48kcal and unsaturated fat (2.9g, but more fiber (1.8g, and sodium (260mg. Four themes emerged from consumer responses: the importance of 1 variety, novelty, choice; 2 cost, affordability, value; 3 health; and 4 food quality, taste. Menu redesign can improve nutrient content, while also increasing sales and revenue. Multi-dimensional assessment of the nutritional, consumer, and retailer implications is desirable practice for enacting similar environmental changes. Keywords: Worksite health promotion, Food environment change, Consumer satisfaction, Menu redesign, Sales and revenue

  4. Does a grill menu redesign influence sales, nutrients purchased, and consumer acceptance in a worksite cafeteria?

    OpenAIRE

    Maya K. Vadiveloo; Vasanti S. Malik; Donna Spiegelman; Walter C. Willett; Josiemer Mattei

    2017-01-01

    Worksite cafeterias are compelling venues to improve diet quality through environmental changes.We conducted a pre-post study to evaluate how a cafeteria-initiated grill menu redesign influenced sales, revenue, and nutrient content of foods purchased. Secondly, we evaluated consumer opinions about menu changes to inform practices for worksite environment interventions. Monthly sales data (2012–2015) were used to compute gross sales and revenue of entrées and side dishes pre-post menu changes....

  5. User Experience Design (UX Design) in a Website Development : Website redesign

    OpenAIRE

    Orlova, Mariia

    2016-01-01

    The purpose of the study was to implement an approach of user experience for a website design. Mostly, I concentrated on revealing and understanding the concepts of UX design which include usability, visual design and human factors affecting the user experience. Another aim of the study was to investigate people’s behaviour related to web design. The thesis based on a project. The project was to redesign an existing web design for a company called Positive Communications. They provide differe...

  6. Redesigning Care Delivery with Patient Support Personnel: Learning from Accountable Care Organizations

    Science.gov (United States)

    Gorbenko, Ksenia O.; Fraze, Taressa; Lewis, Valerie A.

    2017-01-01

    INTRODUCTION Accountable care organizations (ACOs) are a value-based payment model in the United States rooted in holding groups of healthcare providers financially accountable for the quality and total cost of care of their attributed population. To succeed in reaching their quality and efficiency goals, ACOs implement a variety of care delivery changes, including workforce redesign. Patient support personnel (PSP)—non-physician staff such as care coordinators, community health workers, and others—are critical to restructuring care delivery. Little is known about how ACOs are redesigning their patient support personnel in terms of responsibilities, location, and evaluation. METHODS We conducted semi-structured one-hour interviews with 25 executives at 16 distinct ACOs. The interviews were recorded, transcribed, and coded for themes, using a qualitative coding and analysis process. RESULTS ACOs deployed PSP to perform four clusters of responsibilities: care provision, care coordination, logistical help with transportation, and social and emotional support. ACOs deployed these personnel strategically across settings (primary care, inpatient services, emergency department, home care and community) depending on their population needs. Most ACOs used personnel with the same level of training across settings. Few ACOs planned to conduct a comprehensive evaluation of their PSP to optimize their value. DISCUSSION ACO strategies in workforce redesign indicate a shift from a physician-centered to a team-based approach. Employing personnel with varying levels of clinical training to perform different tasks can help further optimize care delivery. More robust evaluation of the deployment of PSP and their performance is needed to demonstrate cost-saving benefits of workforce redesign. PMID:28217305

  7. Redesign and commissioning of sexual health services in England - a qualitative study.

    Science.gov (United States)

    Walker, I F; Leigh-Hunt, N; Lee, A C K

    2016-10-01

    Responsibility for the commissioning of sexual and reproductive health (SRH) services transferred from the National Health Service to local authorities in England in 2013. This transfer prompted many local authorities to undertake new procurements of these SRH services. This study was undertaken to capture some of the lessons learnt in order to inform future commissioning and system redesign. A qualitative study was carried out involving semi-structured interviews. Interviews were conducted with 13 local authority sexual health commissioners in Yorkshire and the Humber from 11 interviews. Thematic analysis was used to identify themes from transcripts of the interviews with the 13 participants. Key themes identified were as follows: the challenge and complexity to those new to clinical commissioning; the prerequisites of robust infrastructural inputs to undertake the process, including technical expertise, a dependable project team, with clarity over the timescales and the budget; the requirement for good governance, stakeholder engagement and successful management of relationships with the latter; and the need to focus on the outcomes, aiming for value for money and improved system performance. Several key issues emerged from our study that significantly influenced the outcome of the redesign and commissioning process for sexual health services. An adapted model of the Donabedian evaluation framework was developed to provide a tool to inform future system redesign. Our model helps identify the key determinants for successful redesign in this context which is essential to both mitigate potential risks and maximize the likelihood of successful outcomes. Our model may have wider applications. Copyright © 2016 The Royal Society for Public Health. Published by Elsevier Ltd. All rights reserved.

  8. Endovascular aneurysm repair delivery redesign leads to quality improvement and cost reduction.

    Science.gov (United States)

    Warner, Courtney J; Horvath, Alexander J; Powell, Richard J; Columbo, Jesse A; Walsh, Teri R; Goodney, Philip P; Walsh, Daniel B; Stone, David H

    2015-08-01

    Endovascular aneurysm repair (EVAR) is now a mainstay of therapy for abdominal aortic aneurysm, although it remains associated with significant expense. We performed a comprehensive analysis of EVAR delivery at an academic medical center to identify targets for quality improvement and cost reduction in light of impending health care reform. All infrarenal EVARs performed from April 2011 to March 2012 were identified (N = 127). Procedures were included if they met standard commercial instructions for use guidelines, used a single manufacturer, and were billed to Medicare diagnosis-related group 238 (n = 49). By use of DMAIC (define, measure, analyze, improve, and control) quality improvement methodology (define, measure, analyze, improve, control), targets for EVAR quality improvement were identified and high-yield changes were implemented. Procedure technical costs were calculated before and after process redesign. Perioperative services and clinic visits were identified as targets for quality improvement efforts and cost reduction. Mean technical costs before the intervention were $31,672, with endograft implants accounting for 52%. Pricing redesign in collaboration with hospital purchasing reduced mean EVAR technical costs to $28,607, a 10% reduction in overall cost, with endograft implants now accounting for 46%. Perioperative implementation of instrument tray redesign reduced instrument use by 32% (184 vs 132 instruments), saving $50,000 annually. Unnecessary clinic visits were reduced by 39% (1.6 vs 1.1 clinic visits per patient) through implementation of a preclinic imaging protocol. There was no difference in mean length of stay after the intervention. Comprehensive EVAR delivery redesign leads to cost reduction and waste elimination while preserving quality. Future efforts to achieve more competitive and transparent device pricing will make EVAR more cost neutral and enhance its financial sustainability for health care systems. Copyright © 2015 Society for

  9. Across the divide: "Primary care departments working together to redesign care to achieve the Triple Aim".

    Science.gov (United States)

    Koslov, Steven; Trowbridge, Elizabeth; Kamnetz, Sandra; Kraft, Sally; Grossman, Jeffrey; Pandhi, Nancy

    2016-09-01

    Primary care is considered the foundation of an effective health care system. However, primary care departments at academic health centers have numerous challenges to overcome when trying to achieve the Triple Aim. As part of an organizational initiative to redesign primary care at a large academic health center, departments of internal medicine, general pediatrics and adolescent medicine, and family medicine worked together to comprehensively redesign primary care. This article describes the process of aligning these three primary care departments: defining panel size, developing a common primary care job description, redesigning the primary care compensation plan, redesigning the care model, and developing standardized staffing. Prior to the initiative, the rate of patient satisfaction was 85%, anticoagulation measurement 65%, pneumococcal vaccination 85%, breast cancer screening 79%, and colorectal cancer screening 69%. These rates all improved to 87%, 75%, 88%, 80%, and 80% respectively. Themes around key challenges to departmental integration are identified: (1) implementing effective communication strategies; (2) addressing specialty differences in primary care delivery; (3) working within resource limitations; and (4) developing long-term sustainability. Primary care in this large academic health center was transformed through developing a united primary care leadership team that bridged individual departments to create and adopt a common vision and solutions to shared problems. Our collaboration has achieved improvements across patient satisfaction, clinical safety metrics, and publicly-reported preventive care outcomes. The description of this experience may be useful for other academic health centers or other non-integrated delivery systems undertaking primary care practice transformation. Copyright © 2015 Elsevier Inc. All rights reserved.

  10. Modular, object-oriented redesign of a large-scale Monte Carlo neutron transport program

    International Nuclear Information System (INIS)

    Moskowitz, B.S.

    2000-01-01

    This paper describes the modular, object-oriented redesign of a large-scale Monte Carlo neutron transport program. This effort represents a complete 'white sheet of paper' rewrite of the code. In this paper, the motivation driving this project, the design objectives for the new version of the program, and the design choices and their consequences will be discussed. The design itself will also be described, including the important subsystems as well as the key classes within those subsystems

  11. Predictability of Conversation Partners

    Science.gov (United States)

    Takaguchi, Taro; Nakamura, Mitsuhiro; Sato, Nobuo; Yano, Kazuo; Masuda, Naoki

    2011-08-01

    Recent developments in sensing technologies have enabled us to examine the nature of human social behavior in greater detail. By applying an information-theoretic method to the spatiotemporal data of cell-phone locations, [C. Song , ScienceSCIEAS0036-8075 327, 1018 (2010)] found that human mobility patterns are remarkably predictable. Inspired by their work, we address a similar predictability question in a different kind of human social activity: conversation events. The predictability in the sequence of one’s conversation partners is defined as the degree to which one’s next conversation partner can be predicted given the current partner. We quantify this predictability by using the mutual information. We examine the predictability of conversation events for each individual using the longitudinal data of face-to-face interactions collected from two company offices in Japan. Each subject wears a name tag equipped with an infrared sensor node, and conversation events are marked when signals are exchanged between sensor nodes in close proximity. We find that the conversation events are predictable to a certain extent; knowing the current partner decreases the uncertainty about the next partner by 28.4% on average. Much of the predictability is explained by long-tailed distributions of interevent intervals. However, a predictability also exists in the data, apart from the contribution of their long-tailed nature. In addition, an individual’s predictability is correlated with the position of the individual in the static social network derived from the data. Individuals confined in a community—in the sense of an abundance of surrounding triangles—tend to have low predictability, and those bridging different communities tend to have high predictability.

  12. Predictability of Conversation Partners

    Directory of Open Access Journals (Sweden)

    Taro Takaguchi

    2011-09-01

    Full Text Available Recent developments in sensing technologies have enabled us to examine the nature of human social behavior in greater detail. By applying an information-theoretic method to the spatiotemporal data of cell-phone locations, [C. Song et al., Science 327, 1018 (2010SCIEAS0036-8075] found that human mobility patterns are remarkably predictable. Inspired by their work, we address a similar predictability question in a different kind of human social activity: conversation events. The predictability in the sequence of one’s conversation partners is defined as the degree to which one’s next conversation partner can be predicted given the current partner. We quantify this predictability by using the mutual information. We examine the predictability of conversation events for each individual using the longitudinal data of face-to-face interactions collected from two company offices in Japan. Each subject wears a name tag equipped with an infrared sensor node, and conversation events are marked when signals are exchanged between sensor nodes in close proximity. We find that the conversation events are predictable to a certain extent; knowing the current partner decreases the uncertainty about the next partner by 28.4% on average. Much of the predictability is explained by long-tailed distributions of interevent intervals. However, a predictability also exists in the data, apart from the contribution of their long-tailed nature. In addition, an individual’s predictability is correlated with the position of the individual in the static social network derived from the data. Individuals confined in a community—in the sense of an abundance of surrounding triangles—tend to have low predictability, and those bridging different communities tend to have high predictability.

  13. Neutronic analysis of the ford nuclear reactor leu core

    International Nuclear Information System (INIS)

    Raza, S.S.; Hayat, T.

    1989-08-01

    Neutronic analysis of the ford nuclear reactor low enriched uranium core has been carried out to gain confidence in the com puting methodology being used for Pakistan Research Reactor-1 core conversion calculations. The computed value of the effective multiplication factor (Keff) is found to be in good agreement with that quoted by others. (author). 6 figs

  14. Converse Barrier Certificate Theorem

    DEFF Research Database (Denmark)

    Wisniewski, Rafael; Sloth, Christoffer

    2013-01-01

    This paper presents a converse barrier certificate theorem for a generic dynamical system.We show that a barrier certificate exists for any safe dynamical system defined on a compact manifold. Other authors have developed a related result, by assuming that the dynamical system has no singular...... points in the considered subset of the state space. In this paper, we redefine the standard notion of safety to comply with generic dynamical systems with multiple singularities. Afterwards, we prove the converse barrier certificate theorem and illustrate the differences between ours and previous work...

  15. Dose conversion factors

    International Nuclear Information System (INIS)

    Kocher, D.C.; Eckerman, K.F.

    1992-01-01

    The following is discussed in this report: concepts and quantities used in calculating radiation dose from internal and external exposure. Tabulations of dose conversion factor for internal and external exposure to radionuclides. Dose conversion factors give dose per unit intake (internal) or dose per unit concentration in environment (external). Intakes of radionuclides for internal exposure and concentrations of radionuclides in environment for external exposure are assumed to be known. Intakes and concentrations are obtained, e.g., from analyses of environmental transport and exposure pathways. differences between dosimetry methods for radionuclides and hazardous chemicals are highlighted

  16. Ocean wave energy conversion

    CERN Document Server

    McCormick, Michael E

    2007-01-01

    This volume will prove of vital interest to those studying the use of renewable resources. Scientists, engineers, and inventors will find it a valuable review of ocean wave mechanics as well as an introduction to wave energy conversion. It presents physical and mathematical descriptions of the nine generic wave energy conversion techniques, along with their uses and performance characteristics.Author Michael E. McCormick is the Corbin A. McNeill Professor of Naval Engineering at the U.S. Naval Academy. In addition to his timely and significant coverage of possible environmental effects associa

  17. Magnetohydrodynamic energy conversion

    International Nuclear Information System (INIS)

    Rosa, R.J.

    1987-01-01

    The object of this book is to present a review of the basic principles and practical aspects of magnetohydrodynamic (MHD) energy conversion. The author has tried to give qualitative semiphysical arguments where possible for the benefit of the reader who is unfamiliar with plasma physics. The aim of MHD energy conversion is to apply to a specific practical goal a part of what has become a vast area of science called plasma physics. The author has attempted to note in the text where a broader view might be fruitful and to give appropriate references

  18. Flexible Conversion Ratio Fast Reactor Systems Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Neil Todreas; Pavel Hejzlar

    2008-06-30

    Conceptual designs of lead-cooled and liquid salt-cooled fast flexible conversion ratio reactors were developed. Both concepts have cores reated at 2400 MWt placed in a large-pool-type vessel with dual-free level, which also contains four intermediate heat exchanges coupling a primary coolant to a compact and efficient supercritical CO2 Brayton cycle power conversion system. Decay heat is removed passively using an enhanced Reactor Vessel Auxiliary Cooling System and a Passive Secondary Auxiliary Cooling System. The most important findings were that (1) it is feasible to design the lead-cooled and salt-cooled reactor with the flexible conversion ratio (CR) in the range of CR=0 and CR=1 n a manner that achieves inherent reactor shutdown in unprotected accidents, (2) the salt-cooled reactor requires Lithium thermal Expansion Modules to overcme the inherent salt coolant's large positive coolant temperature reactivity coefficient, (3) the preferable salt for fast spectrum high power density cores is NaCl-Kcl-MgCl2 as opposed to fluoride salts due to its better themal-hydraulic and neutronic characteristics, and (4) both reactor, but attain power density 3 times smaller than that of the sodium-cooled reactor.

  19. Flexible Conversion Ratio Fast Reactor Systems Evaluation

    International Nuclear Information System (INIS)

    Neil Todreas; Pavel Hejzlar

    2008-01-01

    Conceptual designs of lead-cooled and liquid salt-cooled fast flexible conversion ratio reactors were developed. Both concepts have cores treated at 2400 MWt placed in a large-pool-type vessel with dual-free level, which also contains four intermediate heat exchanges coupling a primary coolant to a compact and efficient supercritical CO2 Brayton cycle power conversion system. Decay heat is removed passively using an enhanced Reactor Vessel Auxiliary Cooling System and a Passive Secondary Auxiliary Cooling System. The most important findings were that (1) it is feasible to design the lead-cooled and salt-cooled reactor with the flexible conversion ratio (CR) in the range of CR=0 and CR=1 n a manner that achieves inherent reactor shutdown in unprotected accidents, (2) the salt-cooled reactor requires Lithium thermal Expansion Modules to overcome the inherent salt coolant's large positive coolant temperature reactivity coefficient, (3) the preferable salt for fast spectrum high power density cores is NaCl-Kcl-MgCl2 as opposed to fluoride salts due to its better thermal-hydraulic and neutronic characteristics, and (4) both reactor, but attain power density 3 times smaller than that of the sodium-cooled reactor

  20. Connecting the dots: interprofessional health education and delivery system redesign at the Veterans Health Administration.

    Science.gov (United States)

    Gilman, Stuart C; Chokshi, Dave A; Bowen, Judith L; Rugen, Kathryn Wirtz; Cox, Malcolm

    2014-08-01

    Health systems around the United States are embracing new models of primary care using interprofessional team-based approaches in pursuit of better patient outcomes, higher levels of satisfaction among patients and providers, and improved overall value. Less often discussed are the implications of new models of care for health professions education, including education for physicians, nurse practitioners, physician assistants, and other professions engaged in primary care. Described here is the interaction between care transformation and redesign of health professions education at the largest integrated delivery system in the United States: the Veterans Health Administration (VA). Challenges and lessons learned are discussed in the context of a demonstration initiative, the VA Centers of Excellence in Primary Care Education. Five sites, involving VA medical centers and their academic affiliates in Boise, Cleveland, San Francisco, Seattle, and West Haven, introduced interprofessional primary care curricula for resident physicians and nurse practitioner students beginning in 2011. Implementation struggles largely revolved around the operational logistics and cultural disruption of integrating educational redesign for medicine and nursing and facilitating the interface between educational and clinical activities. To realize new models for interprofessional teaching, faculty, staff, and trainees must understand the histories, traditions, and program requirements across professions and experiment with new approaches to achieving a common goal. Key recommendations for redesign of health professions education revolve around strengthening the union between interprofessional learning, team-based practice, and high-value care.

  1. Redesigning rain gauges network in Johor using geostatistics and simulated annealing

    Energy Technology Data Exchange (ETDEWEB)

    Aziz, Mohd Khairul Bazli Mohd, E-mail: mkbazli@yahoo.com [Centre of Preparatory and General Studies, TATI University College, 24000 Kemaman, Terengganu, Malaysia and Department of Mathematical Sciences, Faculty of Science, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Yusof, Fadhilah, E-mail: fadhilahy@utm.my [Department of Mathematical Sciences, Faculty of Science, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Daud, Zalina Mohd, E-mail: zalina@ic.utm.my [UTM Razak School of Engineering and Advanced Technology, Universiti Teknologi Malaysia, UTM KL, 54100 Kuala Lumpur (Malaysia); Yusop, Zulkifli, E-mail: zulyusop@utm.my [Institute of Environmental and Water Resource Management (IPASA), Faculty of Civil Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Kasno, Mohammad Afif, E-mail: mafifkasno@gmail.com [Malaysia - Japan International Institute of Technology (MJIIT), Universiti Teknologi Malaysia, UTM KL, 54100 Kuala Lumpur (Malaysia)

    2015-02-03

    Recently, many rainfall network design techniques have been developed, discussed and compared by many researchers. Present day hydrological studies require higher levels of accuracy from collected data. In numerous basins, the rain gauge stations are located without clear scientific understanding. In this study, an attempt is made to redesign rain gauge network for Johor, Malaysia in order to meet the required level of accuracy preset by rainfall data users. The existing network of 84 rain gauges in Johor is optimized and redesigned into a new locations by using rainfall, humidity, solar radiation, temperature and wind speed data collected during the monsoon season (November - February) of 1975 until 2008. This study used the combination of geostatistics method (variance-reduction method) and simulated annealing as the algorithm of optimization during the redesigned proses. The result shows that the new rain gauge location provides minimum value of estimated variance. This shows that the combination of geostatistics method (variance-reduction method) and simulated annealing is successful in the development of the new optimum rain gauge system.

  2. Evaluation of a redesigned 3/4-inch uranium hexafluoride cylinder valve stem

    International Nuclear Information System (INIS)

    Zonner, L.A.; Wamsley, S.D.

    1978-01-01

    The performance of a redesigned 3/4-in. uranium hexafluoride cylinder valve stem has been evaluated at the Portsmouth Gaseous Diffusion Plant. Prototypes, machined from Monel bar stock and having a 45 0 tip angle instead of the 15 0 tip angle of the standard valve stem, were fabricated. Tests included: cyclic leak evaluation; flow restriction determination; wear testing with uranyl fluoride deposits in the valve seat; stress corrosion testing; field testing (in previously rejected valve bodies); and production leak testing. Because their overall test performance was excellent, actual production usage of the redesigned stems was initiated. The in-service performance of valves fitted with redesigned stems has been significantly superior to that of valves having the standard stems: rejection rates have been 0.7 and 16.6 percent, respectively. Recommendations are made to replace all 15 0 angle tip stems presently in service with new stems having a 45 0 angle tip and to specify the new stem tip design for future 3/4-in. valve purchases

  3. Redesigning rain gauges network in Johor using geostatistics and simulated annealing

    International Nuclear Information System (INIS)

    Aziz, Mohd Khairul Bazli Mohd; Yusof, Fadhilah; Daud, Zalina Mohd; Yusop, Zulkifli; Kasno, Mohammad Afif

    2015-01-01

    Recently, many rainfall network design techniques have been developed, discussed and compared by many researchers. Present day hydrological studies require higher levels of accuracy from collected data. In numerous basins, the rain gauge stations are located without clear scientific understanding. In this study, an attempt is made to redesign rain gauge network for Johor, Malaysia in order to meet the required level of accuracy preset by rainfall data users. The existing network of 84 rain gauges in Johor is optimized and redesigned into a new locations by using rainfall, humidity, solar radiation, temperature and wind speed data collected during the monsoon season (November - February) of 1975 until 2008. This study used the combination of geostatistics method (variance-reduction method) and simulated annealing as the algorithm of optimization during the redesigned proses. The result shows that the new rain gauge location provides minimum value of estimated variance. This shows that the combination of geostatistics method (variance-reduction method) and simulated annealing is successful in the development of the new optimum rain gauge system

  4. Redesigning Human Body Systems: Effective Pedagogical Strategy for Promoting Active Learning and STEM Education

    Directory of Open Access Journals (Sweden)

    Abour H. Cherif

    2012-01-01

    Full Text Available The human body is a remarkable biological machine maintained by interdependent body systems and organized biochemical reactions. Evolution has worked on humans for hundreds of thousands of years, yet the current pace of technological and social change have radically affected our life style and have exposed possible human frailties. This raises the question of whether or not nature’s work could be improved upon. We provide two-sided perspectives as a rationale for the need for the redesign of the human body. Then, we describe pedagogical strategy through which students study morphological and anatomical structures and the physiological functions of the human body systems and their respective organs and parts. The students select their own favorite system or organ to redesign in order to optimize the efficiency of the anatomical structural, physiological function, and/or the aesthetic and functional morphology; a redesign that might lead to, for example, lowering risk of diabetes, heart attack, and/or stroke. Through group work and interaction (student groups compete for a prestigious “in-house” patent award, students actively engage in the learning process in order to understand the role of design in the efficiency and functionality and vulnerability to disease of the human body system.

  5. Redesigning rain gauges network in Johor using geostatistics and simulated annealing

    Science.gov (United States)

    Aziz, Mohd Khairul Bazli Mohd; Yusof, Fadhilah; Daud, Zalina Mohd; Yusop, Zulkifli; Kasno, Mohammad Afif

    2015-02-01

    Recently, many rainfall network design techniques have been developed, discussed and compared by many researchers. Present day hydrological studies require higher levels of accuracy from collected data. In numerous basins, the rain gauge stations are located without clear scientific understanding. In this study, an attempt is made to redesign rain gauge network for Johor, Malaysia in order to meet the required level of accuracy preset by rainfall data users. The existing network of 84 rain gauges in Johor is optimized and redesigned into a new locations by using rainfall, humidity, solar radiation, temperature and wind speed data collected during the monsoon season (November - February) of 1975 until 2008. This study used the combination of geostatistics method (variance-reduction method) and simulated annealing as the algorithm of optimization during the redesigned proses. The result shows that the new rain gauge location provides minimum value of estimated variance. This shows that the combination of geostatistics method (variance-reduction method) and simulated annealing is successful in the development of the new optimum rain gauge system.

  6. Reducing and Sustaining Duplicate Medical Record Creation by Usability Testing and System Redesign.

    Science.gov (United States)

    Khunlertkit, Adjhaporn; Dorissaint, Leonard; Chen, Allen; Paine, Lori; Pronovost, Peter J

    2017-10-25

    Duplicate medical record creation is a common and consequential health care systems error often caused by poor search system usability and inappropriate user training. We conducted two phases of scenario-based usability testing with patient registrars working in areas at risk of generating duplicate medical records. Phase 1 evaluated the existing search system, which led to system redesigns. Phase 2 tested the redesigned system to mitigate potential errors before health system-wide implementation. To evaluate system effectiveness, we compared the monthly potential duplicate medical record rates for preimplementation and postimplementation months. The existing system could not effectively handle a misspelling, which led to failed search and duplicate medical record creation. Using the existing system, 96% of registrars found commonly spelled patient names whereas only 69% successfully found complicated names. Registrars lacked knowledge and usage of a phonetic matching function to assist in misspelling. The new system consistently captured the correct patient regardless of misspelling, but search returned more potential matches, resulting in, on average, 4 seconds longer to select common names. Potential monthly duplicate medical record rate reduced by 38%, from 4% to 2.3% after implementation of the new system, and has sustained at an average of 2.5% for 2 years. Usability testing was an effective method to reveal problems and aid system redesign to deliver a more user friendly system, hence reducing the potential for medical record duplication. Greater standards for usability would ensure that these improvements can be realized before rather than after exposing patients to risks.

  7. Status of HEU-LEU conversion of FRJ-2

    International Nuclear Information System (INIS)

    Damm, G.; Nabbi, R.

    2002-01-01

    The operator of the German FRJ-2 research reactor, 'Research Center Juelich', has participated from the beginning in the RERTR programme and made comprehensive contributions to the test and use of LEU fuel for HEU-LEU-conversion measures. The originally planned time scale for the conversion of FRJ-2 was significantly delayed because of a change of the manufacturer of the LEU fuel elements and a 4 years shutdown of the reactor for refurbishment purposes. In the meantime the new LEU fuel elements are qualified and tested in the reactor. In the moment calculations for the safety report are made and it is planned to apply for the license of FRJ-2 operation with LEU fuel at the beginning of 2003. In order to get most reliable results a sophisticated computational method based on a MCNP model coupled with the depletion code BURN was developed for reactor physical calculations, core conversion studies and fuel element performance analysis and applied to the mixed and LEU core. The licensing schedule and results of latest calculations for the conversion study will be presented. The simulations shows that the thermal flux in the LEU core is about 19% resulting in a lower burnup rate. But in the reflector area around the core and in the center of the cold n source the neutron flux reduction remains limited to 6%. Due to a harder neutron spectrum in the LEU core the kinetic and safety related parameters are slightly reduced. Using the ORIGEN code it could be shown that the increase of the total fission products inventory amounts to about 6% compared to a HEU core. As a consequence of the high amount of U-238, the amount of U-235 in the LEU core has to be about 27% higher than in the HEU core but the U-235 burnup is approx. 5% lower due to the contribution of fissile plutonium. (author)

  8. Augustine’s Confessions: Interiority at the Core of the Core Curriculum

    Directory of Open Access Journals (Sweden)

    Michael Chiariello

    2015-06-01

    Full Text Available When St. Bonaventure University decided to redesign its core curriculum, we turned to Bonaventure’s account of the mind’s journey to God in the Itinerarium Mentis in Deum as a paradigm by which to give coherence to the undergraduate experience consistent with our mission and tradition. Bonaventure was himself an Augustinian philosopher and thus Augustine’s Confessions holds a place of great significance in our first year seminar where it is studied in conjunction with Bonaventure’s inward turn to find God imprinted on his soul. This paper is an account of the original rationale for including Augustine’s Confessions in our curriculum and a report of continuing faculty and student attitudes towards that text nearly two decades later.

  9. Catalytic Conversion of Biofuels

    DEFF Research Database (Denmark)

    Jørgensen, Betina

    This thesis describes the catalytic conversion of bioethanol into higher value chemicals. The motivation has been the unavoidable coming depletion of the fossil resources. The thesis is focused on two ways of utilising ethanol; the steam reforming of ethanol to form hydrogen and the partial oxida...

  10. Electrochemical solar energy conversion

    International Nuclear Information System (INIS)

    Gerischer, H.

    1991-01-01

    The principles of solar energy conversion in photoelectrochemical cells are briefly reviewed. Cells for the generation of electric power and for energy storage in form of electrochemical energy are described. These systems are compared with solid state photovoltaic devices, and the inherent difficulties for the operation of the electrochemical systems are analyzed. (author). 28 refs, 10 figs

  11. Converse Barrier Certificate Theorems

    DEFF Research Database (Denmark)

    Wisniewski, Rafael; Sloth, Christoffer

    2016-01-01

    This paper shows that a barrier certificate exists for any safe dynamical system. Specifically, we prove converse barrier certificate theorems for a class of structurally stable dynamical systems. Other authors have developed a related result by assuming that the dynamical system has neither...

  12. Wavelength conversion devices

    DEFF Research Database (Denmark)

    Mikkelsen, Benny; Durhuus, Terji; Jørgensen, Carsten

    1996-01-01

    system requirements. The ideal wavelength converter should be transparent to the bit rate and signal format and provide an unchirped output signal with both a high extinction ratio and a large signal-to-noise ratio. It should allow conversion to both shorter and longer wavelengths with equal performance...

  13. Conversation and research

    NARCIS (Netherlands)

    Schuurman, Jan Gerrit; Veermans, K.H.

    2001-01-01

    Gordon Pask’s conversation theory was created in the 1970s. The theory encompasses a high-level framework for studying interactions between actors in artificial situations where people co-operate, have conflicts, follow rules, negotiate outcomes, invent new rules together, etc. Sadly, the theory is

  14. Catalyst for hydrocarbon conversion

    International Nuclear Information System (INIS)

    Duhaut, P.; Miquel, J.

    1975-01-01

    A description is given for a catalyst and process for hydrocarbon conversions, e.g., reforming. The catalyst contains an alumina carrier, platinum, iridium, at least one metal selected from uranium, vanadium, and gallium, and optionally halogen in the form of metal halide of one of the aforesaid components. (U.S.)

  15. The Nanticoke conversion study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-04-01

    A study was conducted to assess the conversion of the Nanticoke coal-fired power plant to cleaner burning natural gas combined-cycle gas turbines. The Nanticoke Generating Station on Lake Erie is responsible for more than 50 per cent of Ontario Power Generation's (OPG) coal-fired electricity production. The OPG is proposing to work towards compliance with the newly signed Ozone Annex to the 1991 Canada-United States Air Quality Agreement which will require fossil-fueled power plants in southern Ontario to reduce their smog-causing nitrogen oxides emissions by about 50 per cent by 2007. This study assessed the emission reduction benefits and financial costs of conversion compared to continuing to operate Nanticoke as a coal-fired plant. The analysis includes a base case set of data on fuel prices, retrofit costs, fuel efficiencies, annual capacity factors and other parameters. It was determined that conversion would cost the average household less than $3 per month on their electricity bill. Conversion would also reduce emissions nitrogen oxide, a major smog pollutant, by 83 per cent and the particulates that form the most health-threatening portion of smog would be reduced by 100 per cent. 15 tabs., 1 fig.

  16. Leadership is a conversation.

    Science.gov (United States)

    Groysberg, Boris; Slind, Michael

    2012-06-01

    Globalization and new technologies have sharply reduced the efficacy of command-and-control management and its accompanying forms of corporate communication. In the course of a recent research project, the authors concluded that by talking with employees, rather than simply issuing orders, leaders can promote operational flexibility, employee engagement, and tight strategic alignment. Groysberg and Slind have identified four elements of organizational conversation that reflect the essential attributes of interpersonal conversation: intimacy, interactivity, inclusion, and intentionality. Intimacy shifts the focus from a top-down distribution of information to a bottom-up exchange of ideas. Organizational conversation is less corporate in tone and more casual. And it's less about issuing and taking orders than about asking and answering questions. Interactivity entails shunning the simplicity of monologue and embracing the unpredictable vitality of dialogue. Traditional one-way media-print and broadcast, in particular-give way to social media buttressed by social thinking. Inclusion turns employees into full-fledged conversation partners, entitling them to provide their own ideas, often on company channels. They can create content and act as brand ambassadors, thought leaders, and storytellers. Intentionality enables leaders and employees to derive strategically relevant action from the push and pull of discussion and debate.

  17. Predicting AD conversion

    DEFF Research Database (Denmark)

    Liu, Yawu; Mattila, Jussi; Ruiz, Miguel �ngel Mu�oz

    2013-01-01

    To compare the accuracies of predicting AD conversion by using a decision support system (PredictAD tool) and current research criteria of prodromal AD as identified by combinations of episodic memory impairment of hippocampal type and visual assessment of medial temporal lobe atrophy (MTA) on MRI...

  18. Conversion tables. Appendix I

    International Nuclear Information System (INIS)

    McKerrell, H.

    1975-01-01

    Tables are presented for the conversion of standard (5568 year half-life) C-14 dates to calendar years. The major part of the data converts C-14 dates to tree-ring years: additional data are given, based on the Egyptian historical curve. (U.K.)

  19. Wavelength conversion technology

    DEFF Research Database (Denmark)

    Stubkjær, Kristian

    1998-01-01

    Optical wavelength conversion is currently attracting much interest. This is because it enables full flexibility and eases management of WDM fibre networks. The tutorial will review existing and potential application areas. Examples of node architectures and network demonstrators that use wavelen...

  20. Our Digital Conversion

    Science.gov (United States)

    Edwards, Mark

    2012-01-01

    In this article, the author describes their digital conversion initiative at Mooresville Graded School District. The project has placed a MacBook Air laptop in the hands of every 3rd through 12th grader and their teachers in the district over the past four years, with over 5,000 computers distributed. But they believe their academic successes have…

  1. Animal MRI Core

    Data.gov (United States)

    Federal Laboratory Consortium — The Animal Magnetic Resonance Imaging (MRI) Core develops and optimizes MRI methods for cardiovascular imaging of mice and rats. The Core provides imaging expertise,...

  2. Single conversion stage amplifier - SICAM

    Energy Technology Data Exchange (ETDEWEB)

    Ljusev, P.

    2005-12-15

    This Ph.D. thesis presents a thorough analysis of the so called SICAM - SIngle Converter stage AMplifier approach to building direct energy conversion audio power amplifiers. The mainstream approach for building isolated audio power amplifiers today consists of isolated DC power supply and Class D amplifier, which essentially represents a two stage solution, where each of the components can be viewed as separate and independent part. The proposed SICAM solution strives for direct energy conversion from the mains to the audio output, by dedicating the operation of the components one to another and integrating their functions, so that the final audio power amplifier represents a single-stage topology with higher efficiency, lower volume, less board space, lower component count and subsequently lower cost. The SICAM approach is both applicable to non-isolated and isolated audio power amplifiers, but the problems encountered in these two cases are different. Non-isolated SICAM solutions are intended for both AC mains-connected and battery-powered devices. In non-isolated mains-connected SICAMs the main idea is to simplify the power supply or even provide integrated power factor correction (PFC) functions, while still maintaining low component stress and good audio performance by generally decreasing the input voltage level to the Class D audio power amplifier. On the other hand, non-isolated battery-powered SICAMs have to cope with the ever changing battery voltage and provide output voltage levels which are both lower and higher than the battery voltage, while still being simple and single-stage energy conversion solutions. In isolated SICAMs the isolation transformer adjusts the voltage level on the secondary side to the desired level, so the main challenges here are decreasing the size of the magnetic core and reducing the number and size of bulky reactive components as much as possible. The main focus of this thesis is directed towards the isolated SICAMs and

  3. High-conversion HTRs and their fuel cycle

    International Nuclear Information System (INIS)

    Gutmann, H.; Hansen, U.; Larsen, H.; Price, M.S.T.

    1976-01-01

    The high-temperature reactors using graphite as structural core material and helium as coolant represent thermal reactor designs with a very high degree of neutron economy which, when using the thorium fuel cycle, offer, at least theoretically, the possibility of thermal breeding. Though this was already known from previous studies, the economic climate at that time was such that the achievement of high conversion ratios conflicted with the incentive for low fuel cycle costs. Consequently, thorium cycle conversion ratios of around 0.6 were found optimum, and the core and fuel element layout followed from the economic ground rules. The recent change in attitude, brought about partly by the slow process of realization of the limits to the earth's accessible high-grade uranium ore resources and more dramatically by the oil crisis, makes it necessary to concentrate attention again on the high conversion fuel cycles. This report discusses the principles of the core design and the fuel cycle layout for High Conversion HTRs (HCHTRs). Though most of the principles apply equally to HTRs of the pebble-bed and the prismatic fuel element design types, the paper concentrates on the latter. Design and fuel cycle strategies for the full utilization of the high conversion potential are compared with others that aim at easier reprocessing and the ''environmental'' fuel cycle. The paper concludes by discussing operating and fuel cycle characteristics and economics of HCHTRs, and how the latter impinge on the allowable price for uranium ore and the available uranium resources. (author)

  4. Measurements of conversion factor of the Argonauta reactor

    International Nuclear Information System (INIS)

    Souza, M.I.S.

    1988-01-01

    The conversion factor (Fc) in the Argonauta reactor using uranium target prepared by electrodeposition method, irradiated in the core and in thermal collumn with thermal neutrons flux maximum is studied. Some data obtained through γ radiation emited by U-239 are shown. (M.J.C.) [pt

  5. Brief encounters with qualitative methods in health research: conversation analysis

    OpenAIRE

    Miller, Paul K.

    2016-01-01

    This paper provides a brief introductory outline of the conversation analytic method, and some of its applications in health research. Drawing on extant literature and an illustrative original case study of suicide risk-assessment in primary care, the core tenets and techniques of the approach are described.

  6. New Conditions for a Total Neutrino Conversion in a Medium

    OpenAIRE

    Chizhov, M. V.; Petcov, S. T.

    1999-01-01

    A new effect of total neutrino conversion is possible when neutrino propagates through multi-layer medium of nonperiodic constant density layers. The effect can take place in the oscillations in the Earth of the Earth-core-crossing solar and atmospheric neutrinos.

  7. Wind energy conversion system

    Science.gov (United States)

    Longrigg, Paul

    1987-01-01

    The wind energy conversion system includes a wind machine having a propeller connected to a generator of electric power, the propeller rotating the generator in response to force of an incident wind. The generator converts the power of the wind to electric power for use by an electric load. Circuitry for varying the duty factor of the generator output power is connected between the generator and the load to thereby alter a loading of the generator and the propeller by the electric load. Wind speed is sensed electro-optically to provide data of wind speed upwind of the propeller, to thereby permit tip speed ratio circuitry to operate the power control circuitry and thereby optimize the tip speed ratio by varying the loading of the propeller. Accordingly, the efficiency of the wind energy conversion system is maximized.

  8. Clinical linguistics: conversational reflections.

    Science.gov (United States)

    Crystal, David

    2013-04-01

    This is a report of the main points I made in an informal "conversation" with Paul Fletcher and the audience at the 14th ICPLA conference in Cork. The observations arose randomly, as part of an unstructured 1-h Q&A, so they do not provide a systematic account of the subject, but simply reflect the issues which were raised by the conference participants during that time.

  9. Conversations with Miss Jane

    Directory of Open Access Journals (Sweden)

    Geneviève Fabre

    2006-05-01

    Full Text Available Considering the wide range of conversations in the autobiography, this essay will attempt to appraise the importance of these verbal exchanges in relation to the overall narrative structure of the book and to the prevalent oral tradition in Louisiana culture, as both an individual and communal expression. The variety of circumstances, the setting and staging, the interlocutors , and the complex intersection of time and place, of stories and History, will be examined; in these conversations with Miss Jane many actors participate, from  the interviewer-narrator, to most characters; even the reader becomes involved.Speaking, hearing, listening, keeping silent is an elaborate ritual that performs many functions; besides conveying news or rumors, it imparts information on the times and on the life of a “representative” woman whose existence - spanning a whole century- is both singular and emblematic. Most importantly this essay will analyse the resonance of an eventful and often dramatic era on her sensibility and conversely show how her evolving sensibility informs that history and draws attention to aspects that might have passed unnoticed or be forever silenced. Jane’s desire for liberty and justice is often challenged as she faces the possibilities of life or death.Conversations build up a complex, often contradictory, but compelling portrait: torn between silence and vehemence, between memories and the urge to meet the future, Jane summons body and mind to find her way through the maze of a fast changing world; self-willed and obstinate she claims her right to speak, to express with wit and wisdom her firm belief in the word, in the ability to express deep seated convictions and faith and a whole array of feelings and emotions.

  10. Performance testing of a mixed TRIGA core

    Energy Technology Data Exchange (ETDEWEB)

    Schumacher, R F; Godsey, T A; Feltz, D E; Randall, J D [Texas A and M University (United States)

    1974-07-01

    The major operational problem experienced by the Nuclear Science Center Reactor at Texas A and M University is full burnup. With two shift operation caused by the high utilization of the facility, the reactor is operated more than 100 megawatt days per year. The solution chosen for this problem was conversion to FLIP fuel. Since funds were not available to load an entire FLIP core, a mixed core comprised of approximately one third FLIP fuel located in the central region was designed. The design core was loaded and went critical on July 1, 1973. The results of the following measurements on the mixed core are presented: Determination of Rod worths; Measurement of Reactivity Effects; Determination of Flux values; Measurement of Fuel temperatures; Preliminary Fuel Burnup Rate; Pulsing Calibration. (author)

  11. Conversion of Questionnaire Data

    International Nuclear Information System (INIS)

    Powell, Danny H.; Elwood, Robert H. Jr.

    2011-01-01

    During the survey, respondents are asked to provide qualitative answers (well, adequate, needs improvement) on how well material control and accountability (MC and A) functions are being performed. These responses can be used to develop failure probabilities for basic events performed during routine operation of the MC and A systems. The failure frequencies for individual events may be used to estimate total system effectiveness using a fault tree in a probabilistic risk analysis (PRA). Numeric risk values are required for the PRA fault tree calculations that are performed to evaluate system effectiveness. So, the performance ratings in the questionnaire must be converted to relative risk values for all of the basic MC and A tasks performed in the facility. If a specific material protection, control, and accountability (MPC and A) task is being performed at the 'perfect' level, the task is considered to have a near zero risk of failure. If the task is performed at a less than perfect level, the deficiency in performance represents some risk of failure for the event. As the degree of deficiency in performance increases, the risk of failure increases. If a task that should be performed is not being performed, that task is in a state of failure. The failure probabilities of all basic events contribute to the total system risk. Conversion of questionnaire MPC and A system performance data to numeric values is a separate function from the process of completing the questionnaire. When specific questions in the questionnaire are answered, the focus is on correctly assessing and reporting, in an adjectival manner, the actual performance of the related MC and A function. Prior to conversion, consideration should not be given to the numeric value that will be assigned during the conversion process. In the conversion process, adjectival responses to questions on system performance are quantified based on a log normal scale typically used in human error analysis (see A

  12. Core Hunter 3: flexible core subset selection.

    Science.gov (United States)

    De Beukelaer, Herman; Davenport, Guy F; Fack, Veerle

    2018-05-31

    Core collections provide genebank curators and plant breeders a way to reduce size of their collections and populations, while minimizing impact on genetic diversity and allele frequency. Many methods have been proposed to generate core collections, often using distance metrics to quantify the similarity of two accessions, based on genetic marker data or phenotypic traits. Core Hunter is a multi-purpose core subset selection tool that uses local search algorithms to generate subsets relying on one or more metrics, including several distance metrics and allelic richness. In version 3 of Core Hunter (CH3) we have incorporated two new, improved methods for summarizing distances to quantify diversity or representativeness of the core collection. A comparison of CH3 and Core Hunter 2 (CH2) showed that these new metrics can be effectively optimized with less complex algorithms, as compared to those used in CH2. CH3 is more effective at maximizing the improved diversity metric than CH2, still ensures a high average and minimum distance, and is faster for large datasets. Using CH3, a simple stochastic hill-climber is able to find highly diverse core collections, and the more advanced parallel tempering algorithm further increases the quality of the core and further reduces variability across independent samples. We also evaluate the ability of CH3 to simultaneously maximize diversity, and either representativeness or allelic richness, and compare the results with those of the GDOpt and SimEli methods. CH3 can sample equally representative cores as GDOpt, which was specifically designed for this purpose, and is able to construct cores that are simultaneously more diverse, and either are more representative or have higher allelic richness, than those obtained by SimEli. In version 3, Core Hunter has been updated to include two new core subset selection metrics that construct cores for representativeness or diversity, with improved performance. It combines and outperforms the

  13. Nuclear spin conversion in formaldehyde

    OpenAIRE

    Chapovsky, Pavel L.

    2000-01-01

    Theoretical model of the nuclear spin conversion in formaldehyde (H2CO) has been developed. The conversion is governed by the intramolecular spin-rotation mixing of molecular ortho and para states. The rate of conversion has been found equal 1.4*10^{-4}~1/s*Torr. Temperature dependence of the spin conversion has been predicted to be weak in the wide temperature range T=200-900 K.

  14. Redesign of a health science centre: reflections on co-leadership.

    Science.gov (United States)

    MacTavish, M; Norton, P

    1995-01-01

    Since 1988, the Sunnybrook Health Science Centre has been proactive in re-designing its system toward decentralized management, the purpose being to further enhance patient care. This process has involved numerous changes, among which were the establishment of three large clinical units. These clinical units are not defined following the historic medical model, but group patients with similar service and care needs. Subsequently, each of the clinical units defined Patient Service Units (PSUs). The hospital has chosen a co-leadership model for the lead management at each of the unit levels. This paper describes the model for clinical units.

  15. Integrating biological redesign: where synthetic biology came from and where it needs to go.

    Science.gov (United States)

    Way, Jeffrey C; Collins, James J; Keasling, Jay D; Silver, Pamela A

    2014-03-27

    Synthetic biology seeks to extend approaches from engineering and computation to redesign of biology, with goals such as generating new chemicals, improving human health, and addressing environmental issues. Early on, several guiding principles of synthetic biology were articulated, including design according to specification, separation of design from fabrication, use of standardized biological parts and organisms, and abstraction. We review the utility of these principles over the past decade in light of the field's accomplishments in building complex systems based on microbial transcription and metabolism and describe the progress in mammalian cell engineering. Copyright © 2014 Elsevier Inc. All rights reserved.

  16. Redesigning and Manufacturing of a Land Levelling Shovel by Assembly Structural Stress Analysis

    OpenAIRE

    Tahir Altinbalik; Gürkan İrsel

    2014-01-01

    The aim was to redesign and manufacture of a shovel for a pull-type land levelling machine, which, in its present condition, is used to get easily damaged even under low loads. Firstly, the maximum pulling load affecting the levelling shovel was experimentally determined. Then, stable-shovel system with the bolt connection was replaced with a bearing-shaft connection system. In this way, the new shovel has gained a capability of making oscillation motion so that it can operate on sloped groun...

  17. Methodological conception of design and re-design of career in the Universidad Internacional SEK Ecuador

    Directory of Open Access Journals (Sweden)

    Enrique Aurelio Barrios-Queipo

    2017-01-01

    Full Text Available Given the challenges in the training of professionals, improving training offer university degrees, from its design and systematic curriculum redesign, it is one of the challenges of higher priority in the Ecuadorian Higher Education. In the article the fundamentals of the views that support how to develop these processes so that a new training offer interest is achieved and at the same time have a character for the future of synthesized contextual socioeconomic development. Structural systemic functional method was applied, develándose that relations between the professional process, the training process and the process of university relevance, can condense pertinent to college.

  18. Redesigning models of patient care delivery and organisation: building collegial generosity in response to workplace challenges.

    Science.gov (United States)

    Chiarella, E Mary

    2007-04-01

    This case study describes the New South Wales Nursing and Midwifery Office (NaMO) Models of Care Project, a project designed to identify, encourage and disseminate innovations in nursing care organisation and delivery. The project is a 4-year action research project, using a range of interactive engagements including workshops, seminars, questionnaires and websites to achieve the goals. This case study briefly describes the main stimuli for review and redesign of models of care identified through analysis of the clinicians' presentations, and explores the range of responses to the workplace challenges.

  19. Microbial Energy Conversion

    Energy Technology Data Exchange (ETDEWEB)

    Buckley, Merry [American Society for Microbiology (ASM), Washington, DC (United States); Wall, Judy D. [Univ. of Missouri, Columbia, MO (United States)

    2006-10-01

    The American Academy of Microbiology convened a colloquium March 10-12, 2006, in San Francisco, California, to discuss the production of energy fuels by microbial conversions. The status of research into various microbial energy technologies, the advantages and disadvantages of each of these approaches, research needs in the field, and education and training issues were examined, with the goal of identifying routes for producing biofuels that would both decrease the need for fossil fuels and reduce greenhouse gas emissions. Currently, the choices for providing energy are limited. Policy makers and the research community must begin to pursue a broader array of potential energy technologies. A diverse energy portfolio that includes an assortment of microbial energy choices will allow communities and consumers to select the best energy solution for their own particular needs. Funding agencies and governments alike need to prepare for future energy needs by investing both in the microbial energy technologies that work today and in the untested technologies that will serve the world’s needs tomorrow. More mature bioprocesses, such as ethanol production from starchy materials and methane from waste digestors, will find applications in the short term. However, innovative techniques for liquid fuel or biohydrogen production are among the longer term possibilities that should also be vigorously explored, starting now. Microorganisms can help meet human energy needs in any of a number of ways. In their most obvious role in energy conversion, microorganisms can generate fuels, including ethanol, hydrogen, methane, lipids, and butanol, which can be burned to produce energy. Alternatively, bacteria can be put to use in microbial fuel cells, where they carry out the direct conversion of biomass into electricity. Microorganisms may also be used some day to make oil and natural gas technologies more efficient by sequestering carbon or by assisting in the recovery of oil and

  20. Infrared up-conversion microscope

    DEFF Research Database (Denmark)

    2014-01-01

    There is presented an up-conversion infrared microscope (110) arranged for imaging an associated object (130), wherein the up-conversion infrared microscope (110) comprises a non-linear crystal (120) arranged for up-conversion of infrared electromagnetic radiation, and wherein an objective optical...

  1. Infrared up-conversion telescope

    DEFF Research Database (Denmark)

    2014-01-01

    There is presented to an up-conversion infrared telescope (110) arranged for imaging an associated scene (130), wherein the up-conversion infrared telescope (110) comprises a non-linear crystal (120) arranged for up-conversion of infrared electromagnetic radiation, and wherein a first optical...

  2. k-core covers and the core

    NARCIS (Netherlands)

    Sanchez-Rodriguez, E.; Borm, Peter; Estevez-Fernandez, A.; Fiestras-Janeiro, G.; Mosquera, M.A.

    This paper extends the notion of individual minimal rights for a transferable utility game (TU-game) to coalitional minimal rights using minimal balanced families of a specific type, thus defining a corresponding minimal rights game. It is shown that the core of a TU-game coincides with the core of

  3. An Analysis of How Carl Rogers Enacted Client-Centered Conversation with Gloria.

    Science.gov (United States)

    Wickman, Scott A.; Campbell, Cynthia

    2003-01-01

    This study analyzed Carl Rogers's session with Gloria in "Three Approaches to Psychotherapy" to determine how Rogers's conversational style functioned to enact his core conditions of empathy, genuineness, and unconditional positive regard. Rogers's conversational style was found to be congruent with his espoused theory as well as a…

  4. The FLIC conversion codes

    International Nuclear Information System (INIS)

    Basher, J.C.

    1965-05-01

    This report describes the FORTRAN programmes, FLIC 1 and FLIC 2. These programmes convert programmes coded in one dialect of FORTRAN to another dialect of the same language. FLIC 1 is a general pattern recognition and replacement programme whereas FLIC 2 contains extensions directed towards the conversion of FORTRAN II and S2 programmes to EGTRAN 1 - the dialect now in use on the Winfrith KDF9. FII or S2 statements are replaced where possible by their E1 equivalents; other statements which may need changing are flagged. (author)

  5. Zinc phosphate conversion coatings

    Science.gov (United States)

    Sugama, Toshifumi

    1997-01-01

    Zinc phosphate conversion coatings for producing metals which exhibit enhanced corrosion prevention characteristics are prepared by the addition of a transition-metal-compound promoter comprising a manganese, iron, cobalt, nickel, or copper compound and an electrolyte such as polyacrylic acid, polymethacrylic acid, polyitaconic acid and poly-L-glutamic acid to a phosphating solution. These coatings are further improved by the incorporation of Fe ions. Thermal treatment of zinc phosphate coatings to generate .alpha.-phase anhydrous zinc phosphate improves the corrosion prevention qualities of the resulting coated metal.

  6. The FLIC conversion codes

    Energy Technology Data Exchange (ETDEWEB)

    Basher, J C [General Reactor Physics Division, Atomic Energy Establishment, Winfrith, Dorchester, Dorset (United Kingdom)

    1965-05-15

    This report describes the FORTRAN programmes, FLIC 1 and FLIC 2. These programmes convert programmes coded in one dialect of FORTRAN to another dialect of the same language. FLIC 1 is a general pattern recognition and replacement programme whereas FLIC 2 contains extensions directed towards the conversion of FORTRAN II and S2 programmes to EGTRAN 1 - the dialect now in use on the Winfrith KDF9. FII or S2 statements are replaced where possible by their E1 equivalents; other statements which may need changing are flagged. (author)

  7. Moodle 20 Course Conversion

    CERN Document Server

    Wild, Ian

    2011-01-01

    With clear instructions and plenty of screenshots, this book provides all the support and guidance you will need as you begin to convert your teaching to Moodle. Step-by-step tutorials use real-world examples to show you how to convert to Moodle in the most efficient and effective ways possible. Moodle Course Conversion carefully illustrates how Moodle can be used to teach content and ideas and clearly demonstrates the advantages of doing so. This book is for teachers, tutors, and lecturers who already have a large body of teaching material and want to use Moodle to enhance their course, rathe

  8. Solar energy conversion

    CERN Document Server

    Likhtenshtein, Gertz I

    2012-01-01

    Finally filling a gap in the literature for a text that also adopts the chemist?s view of this hot topic, Prof Likhtenshtein, an experienced author and internationally renowned scientist, considers different physical and engineering aspects in solar energy conversion. From theory to real-life systems, he shows exactly which chemical reactions take place when converting light energy, providing an overview of the chemical perspective from fundamentals to molecular harvesting systems and solar cells. This essential guide will thus help researchers in academia and industry better understa

  9. Gas core reactors for coal gasification

    International Nuclear Information System (INIS)

    Weinstein, H.

    1976-01-01

    The concept of using a gas core reactor to produce hydrogen directly from coal and water is presented. It is shown that the chemical equilibrium of the process is strongly in favor of the production of H 2 and CO in the reactor cavity, indicating a 98 percent conversion of water and coal at only 1500 0 K. At lower temperatures in the moderator-reflector cooling channels the equilibrium strongly favors the conversion of CO and additional H 2 O to CO 2 and H 2 . Furthermore, it is shown the H 2 obtained per pound of carbon has 23 percent greater heating value than the carbon so that some nuclear energy is also fixed. Finally, a gas core reactor plant floating in the ocean is conceptualized which produces H 2 , fresh water and sea salts from coal

  10. Calculation of the packing fraction in a pebble-bed ADS and redesigning of the Transmutation Advanced Device for Sustainable Energy Applications (TADSEA)

    International Nuclear Information System (INIS)

    García, L.; Pérez, J.; García, C.; Escrivá, A.; Rosales, J.; Abánades, A.

    2012-01-01

    Highlights: ► We based our study on an ADS for TRU transmutation and high temperature production. ► We calculated the number of pebbles that fit in a cylindrical ADS core. ► In both ADS design options studied, the mass of Pu isotopes reduces considerably. ► The system can reach coolant outlet temperatures high enough for hydrogen production. ► The maximum temperature values obtained in the ADS are not dangerous for TRISO fuel. - Abstract: One of the main problems that should be addressed in the use of nuclear fuels for heat and electricity production is the management of nuclear waste from conventional nuclear power plants and its inventory minimization. Fast reactors and Accelerator Driven Systems (ADSs) are the main options for reducing the long-lived radioactive waste inventory. In previous studies, the conceptual design of a Transmutation Advanced Device for Sustainable Energy Applications (TADSEA) has been made. The TADSEA is a pebble-bed ADS cooled by helium and moderated by graphite; it uses as fuel small amounts of transuranic elements in the form of TRISO particles, confined in 3 cm radius graphite pebbles. It has been conceived for Plutonium (Pu) and Minor Actinides (MA) transmutation and for achieving very high helium temperatures at the core's outlet to match the thermal requirements for hydrogen production by high temperature electrolysis (HTE) or by the iodine-sulfur (I–S) thermo-chemical cycle. In this paper, a geometrical method for calculating the real number of pebbles that fit in a cylindrical ADS core, according to its size and pebble configuration, is described. Based on its results, the packing fraction influence on the TADSEA's main work parameters is studied, and the redesign of the previous configuration is done in order to maintain the exit thermal power established in the preliminary design. Results have shown the capability of the system to reach coolant outlet temperatures high enough for its application to hydrogen

  11. Microbial conversion technologies

    Energy Technology Data Exchange (ETDEWEB)

    Lau, P. [National Research Council of Canada, Ottawa, ON (Canada). Bioconversion and Sustainable Development

    2006-07-01

    Microbes are a biomass and an valuable resource. This presentation discussed microbial conversion technologies along with background information on microbial cells, their characteristics and microbial diversity. Untapped opportunities for microbial conversion were identified. Metagenomic and genome mining approaches were also discussed, as they can provide access to uncultivated or unculturable microorganisms in communal populations and are an unlimited resource for biocatalysts, novel genes and metabolites. Genome mining was seen as an economical approach. The presentation also emphasized that the development of microbial biorefineries would require significant insights into the relevant microorganisms and that biocatalysts were the ultimate in sustainability. In addition, the presentation discussed the natural fibres initiative for biochemicals and biomaterials. Anticipated outputs were identified and work in progress of a new enzyme-retting cocktail to provide diversity and/or consistency in fibre characteristics for various applications were also presented. It was concluded that it is necessary to leverage understanding of biological processes to produce bioproducts in a clean and sustainable manner. tabs., figs.

  12. Communal biomass conversion plants

    International Nuclear Information System (INIS)

    1991-06-01

    The Coordinating Committee set up by the Danish government in 1986 were given the responsibility of investigating the potentials for biomass conversion plants in Denmark, especially in relation to agricultural, environmental and energy aspects. The results of the Committee's plan of management for this project are presented. This main report covers 13 background reports which deal with special aspects in detail. The report describes the overall plan of management, the demonstration and follow-up programme and the individual biogas demonstration plants. Information gained from these investigations is presented. The current general status, (with emphasis on the technical and economical aspects) and the prospects for the future are discussed. The interest other countries have shown in Danish activities within the field of biogas production is described, and the possibilities for Danish export of technology and know-how in this relation are discussed. It is claimed that Denmark is the first country that has instigated a coordinated development programme for biomass conversion plants. (AB) 24 refs

  13. Online optimal experimental re-design in robotic parallel fed-batch cultivation facilities.

    Science.gov (United States)

    Cruz Bournazou, M N; Barz, T; Nickel, D B; Lopez Cárdenas, D C; Glauche, F; Knepper, A; Neubauer, P

    2017-03-01

    We present an integrated framework for the online optimal experimental re-design applied to parallel nonlinear dynamic processes that aims to precisely estimate the parameter set of macro kinetic growth models with minimal experimental effort. This provides a systematic solution for rapid validation of a specific model to new strains, mutants, or products. In biosciences, this is especially important as model identification is a long and laborious process which is continuing to limit the use of mathematical modeling in this field. The strength of this approach is demonstrated by fitting a macro-kinetic differential equation model for Escherichia coli fed-batch processes after 6 h of cultivation. The system includes two fully-automated liquid handling robots; one containing eight mini-bioreactors and another used for automated at-line analyses, which allows for the immediate use of the available data in the modeling environment. As a result, the experiment can be continually re-designed while the cultivations are running using the information generated by periodical parameter estimations. The advantages of an online re-computation of the optimal experiment are proven by a 50-fold lower average coefficient of variation on the parameter estimates compared to the sequential method (4.83% instead of 235.86%). The success obtained in such a complex system is a further step towards a more efficient computer aided bioprocess development. Biotechnol. Bioeng. 2017;114: 610-619. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  14. Evaluating and redesigning teaching learning sequences at the introductory physics level

    Science.gov (United States)

    Guisasola, Jenaro; Zuza, Kristina; Ametller, Jaume; Gutierrez-Berraondo, José

    2017-12-01

    In this paper we put forward a proposal for the design and evaluation of teaching and learning sequences in upper secondary school and university. We will connect our proposal with relevant contributions on the design of teaching sequences, ground it on the design-based research methodology, and discuss how teaching and learning sequences designed according to our proposal relate to learning progressions. An iterative methodology for evaluating and redesigning the teaching and learning sequence (TLS) is presented. The proposed assessment strategy focuses on three aspects: (a) evaluation of the activities of the TLS, (b) evaluation of learning achieved by students in relation to the intended objectives, and (c) a document for gathering the difficulties found when implementing the TLS to serve as a guide to teachers. Discussion of this guide with external teachers provides feedback used for the TLS redesign. The context of our implementation and evaluation is an innovative calculus-based physics course for first-year engineering and science degree students at the University of the Basque Country.

  15. Redesign of a computerized clinical reminder for colorectal cancer screening: a human-computer interaction evaluation

    Directory of Open Access Journals (Sweden)

    Saleem Jason J

    2011-11-01

    Full Text Available Abstract Background Based on barriers to the use of computerized clinical decision support (CDS learned in an earlier field study, we prototyped design enhancements to the Veterans Health Administration's (VHA's colorectal cancer (CRC screening clinical reminder to compare against the VHA's current CRC reminder. Methods In a controlled simulation experiment, 12 primary care providers (PCPs used prototypes of the current and redesigned CRC screening reminder in a within-subject comparison. Quantitative measurements were based on a usability survey, workload assessment instrument, and workflow integration survey. We also collected qualitative data on both designs. Results Design enhancements to the VHA's existing CRC screening clinical reminder positively impacted aspects of usability and workflow integration but not workload. The qualitative analysis revealed broad support across participants for the design enhancements with specific suggestions for improving the reminder further. Conclusions This study demonstrates the value of a human-computer interaction evaluation in informing the redesign of information tools to foster uptake, integration into workflow, and use in clinical practice.

  16. Employee health benefit redesign at the academic health center: a case study.

    Science.gov (United States)

    Marshall, Julie; Weaver, Deirdre C; Splaine, Kevin; Hefner, David S; Kirch, Darrell G; Paz, Harold L

    2013-03-01

    The rapidly escalating cost of health care, including the cost of providing health care benefits, is a significant concern for many employers. In this article, the authors examine a case study of an academic health center that undertook a complete redesign of its health benefit structure to control rising costs, encourage use of its own provider network, and support employee wellness. With the implementation in 2006 of a high-deductible health plan combined with health reimbursement arrangements and wellness incentives, the Penn State Hershey Medical Center (PSHMC) was able to realize significant cost savings and increase use of its own network while maintaining a high level of employee satisfaction. By contracting with a single third-party administrator for its self-insured plan, PSHMC reduced its administrative costs and simplified benefit choices for employees. In addition, indexing employee costs to salary ensured that this change was equitable for all employees, and the shift to a consumer-driven health plan led to greater employee awareness of health care costs. The new health benefit plan's strong focus on employee wellness and preventive health has led to significant increases in the use of preventive health services, including health risk assessments, cancer screenings, and flu shots. PSHMC's experience demonstrates the importance of clear and ongoing communication with employees throughout--before, during, and even after--the process of health benefit redesign.

  17. Using the Principles of SoTL to Redesign an Advanced Evolutionary Biology Course

    Directory of Open Access Journals (Sweden)

    Michael deBraga

    2015-03-01

    Full Text Available A primary goal of university instruction is the students’ demonstration of improved, highly developed critical thinking (CT skills. However, how do faculty encourage CT and its potential concomitant increase in student workload without negatively impacting student perceptions of the course? In this investigation, an advanced biology course is evaluated after structural changes (implemented in 2010 met with a poor student evaluation of the course and the instructor. This analysis first examines the steps used to transform a course to encourage CT and then explains how it can be assessed. To accomplish these goals, the instructor collaborated with an educational developer to redesign the course using a philosophy informed by SoTL. This approach, as we see it, represents a set of principles that demand transparency in the development and application of strategies whose aim is to encourage student learning. However, the SoTL approach would be insufficient to simply promote a set of strategies without some mechanism for evaluating its efficacy. Therefore, we designed a “Graded Response” (GR multiple-choice test to measure CT development and hence to properly evaluate whether the strategies embedded in our SoTL-informed course redesign have adequately met our goals.

  18. Iterative learning-based decentralized adaptive tracker for large-scale systems: a digital redesign approach.

    Science.gov (United States)

    Tsai, Jason Sheng-Hong; Du, Yan-Yi; Huang, Pei-Hsiang; Guo, Shu-Mei; Shieh, Leang-San; Chen, Yuhua

    2011-07-01

    In this paper, a digital redesign methodology of the iterative learning-based decentralized adaptive tracker is proposed to improve the dynamic performance of sampled-data linear large-scale control systems consisting of N interconnected multi-input multi-output subsystems, so that the system output will follow any trajectory which may not be presented by the analytic reference model initially. To overcome the interference of each sub-system and simplify the controller design, the proposed model reference decentralized adaptive control scheme constructs a decoupled well-designed reference model first. Then, according to the well-designed model, this paper develops a digital decentralized adaptive tracker based on the optimal analog control and prediction-based digital redesign technique for the sampled-data large-scale coupling system. In order to enhance the tracking performance of the digital tracker at specified sampling instants, we apply the iterative learning control (ILC) to train the control input via continual learning. As a result, the proposed iterative learning-based decentralized adaptive tracker not only has robust closed-loop decoupled property but also possesses good tracking performance at both transient and steady state. Besides, evolutionary programming is applied to search for a good learning gain to speed up the learning process of ILC. Copyright © 2011 ISA. Published by Elsevier Ltd. All rights reserved.

  19. Computational Re-design of Synthetic Genetic Oscillators for Independent Amplitude and Frequency Modulation.

    Science.gov (United States)

    Tomazou, Marios; Barahona, Mauricio; Polizzi, Karen M; Stan, Guy-Bart

    2018-04-25

    To perform well in biotechnology applications, synthetic genetic oscillators must be engineered to allow independent modulation of amplitude and period. This need is currently unmet. Here, we demonstrate computationally how two classic genetic oscillators, the dual-feedback oscillator and the repressilator, can be re-designed to provide independent control of amplitude and period and improve tunability-that is, a broad dynamic range of periods and amplitudes accessible through the input "dials." Our approach decouples frequency and amplitude modulation by incorporating an orthogonal "sink module" where the key molecular species are channeled for enzymatic degradation. This sink module maintains fast oscillation cycles while alleviating the translational coupling between the oscillator's transcription factors and output. We characterize the behavior of our re-designed oscillators over a broad range of physiologically reasonable parameters, explain why this facilitates broader function and control, and provide general design principles for building synthetic genetic oscillators that are more precisely controllable. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights reserved.

  20. Regional process redesign of lung cancer care: a learning health system pilot project.

    Science.gov (United States)

    Fung-Kee-Fung, M; Maziak, D E; Pantarotto, J R; Smylie, J; Taylor, L; Timlin, T; Cacciotti, T; Villeneuve, P J; Dennie, C; Bornais, C; Madore, S; Aquino, J; Wheatley-Price, P; Ozer, R S; Stewart, D J

    2018-02-01

    The Ottawa Hospital (toh) defined delay to timely lung cancer care as a system design problem. Recognizing the patient need for an integrated journey and the need for dynamic alignment of providers, toh used a learning health system (lhs) vision to redesign regional diagnostic processes. A lhs is driven by feedback utilizing operational and clinical information to drive system optimization and innovation. An essential component of a lhs is a collaborative platform that provides connectivity across silos, organizations, and professions. To operationalize a lhs, we developed the Ottawa Health Transformation Model (ohtm) as a consensus approach that addresses process barriers, resistance to change, and conflicting priorities. A regional Community of Practice (cop) was established to engage stakeholders, and a dedicated transformation team supported process improvements and implementation. The project operationalized the lung cancer diagnostic pathway and optimized patient flow from referral to initiation of treatment. Twelve major processes in referral, review, diagnostics, assessment, triage, and consult were redesigned. The Ottawa Hospital now provides a diagnosis to 80% of referrals within the provincial target of 28 days. The median patient journey from referral to initial treatment decreased by 48% from 92 to 47 days. The initiative optimized regional integration from referral to initial treatment. Use of a lhs lens enabled the creation of a system that is standardized to best practice and open to ongoing innovation. Continued transformation initiatives across the continuum of care are needed to incorporate best practice and optimize delivery systems for regional populations.

  1. Human factors engineering and design validation for the redesigned follitropin alfa pen injection device.

    Science.gov (United States)

    Mahony, Mary C; Patterson, Patricia; Hayward, Brooke; North, Robert; Green, Dawne

    2015-05-01

    To demonstrate, using human factors engineering (HFE), that a redesigned, pre-filled, ready-to-use, pre-asembled follitropin alfa pen can be used to administer prescribed follitropin alfa doses safely and accurately. A failure modes and effects analysis identified hazards and harms potentially caused by use errors; risk-control measures were implemented to ensure acceptable device use risk management. Participants were women with infertility, their significant others, and fertility nurse (FN) professionals. Preliminary testing included 'Instructions for Use' (IFU) and pre-validation studies. Validation studies used simulated injections in a representative use environment; participants received prior training on pen use. User performance in preliminary testing led to IFU revisions and a change to outer needle cap design to mitigate needle stick potential. In the first validation study (49 users, 343 simulated injections), in the FN group, one observed critical use error resulted in a device design modification and another in an IFU change. A second validation study tested the mitigation strategies; previously reported use errors were not repeated. Through an iterative process involving a series of studies, modifications were made to the pen design and IFU. Simulated-use testing demonstrated that the redesigned pen can be used to administer follitropin alfa effectively and safely.

  2. Redesigning the Structure of Republic Indonesian Defense System; An Analysis of Systems Thinking

    Directory of Open Access Journals (Sweden)

    Ade Muhammad

    2013-09-01

    Full Text Available The phenomenon of Shrinking Defense Capabilities is only the tip of the iceberg of Indonesian Defense System’s problem. The root of the problem that lies beneath and outside is keep untouched. This journal is the part of the efforts to reveal the phenomenon’s structure that binding as a system. The present structure is a cause of that phenomenon and the basis of the current organization responsible for Republic Indonesia Defense sector. With the Systems thinking analysis, the research has revealed the structure that become the problem cause and give a holistic solution trough redesigning new structure based on two theories namely the Strategic-Operational Management with Vision Dissemination of Prof. Dr. Jürgen Strohhecker and the Defense System Generic Dr. Ir. Muhammad Tasrif, M.Eng and Ir. Ade Muhammad, M.Han. The logical consequences would also changing of formation of Indonesian Defense Organization. Keywords : Design, Redesigning, Defense System, System, Defense, Holistic

  3. Redesign and Automation of a mold for manufacturing of refrigerated display cases using Polyurethane Foam Injection

    Directory of Open Access Journals (Sweden)

    Eugenio Yime

    2016-10-01

    Full Text Available Context: To stay competitive over time, a company must continually submit their processes to improvements and updates. Herein are proposed some improvements with regard to safety at work and the reduction of time that occurs during the operation of a mold for manufacturing refrigerators. Method: Some operating conditions of the mold are analyzed and then some factors affecting the processing time and the safety of operating personnel are established. The weaknesses found are related to the intrinsic design of the mold, which raises the need for a structural redesign that also includes automation. Results: It is presented a new design and way to operate the mold which reduces the risk of accidents at having no heavy loads over operator heads. Another contribution of the redesign is the increase in the system rigidity which helps to reduce manufacturing defects. Finally, it is show a automation design which helps to reduce manufacturing times. Conclusions: Significant improvements were obtained in the operation of the mold, such as the reduction of occupational hazards and reduced manufacturing time of refrigerators. These improvements translate into benefits for the company, by reducing costs and increasing production. Both benefits help strengthen the competitiveness of the company.

  4. Participatory redesign of work organisation in hospital nursing: A study of the implementation process.

    Science.gov (United States)

    Stab, Nicole; Hacker, Winfried

    2018-05-01

    The main goal of the study was to apply and analyse a moderated participatory small-group procedure with registered nurses, which aims at the development and implementation of measures to improve work organisation in hospital wards and nursing units. Participation in job redesign is an essential prerequisite of the successful implementation of improvement measures in nursing. The study was carried out in a public hospital of maximum care in Germany. We selected 25 wards with the most critical reported exhaustion and general health and applied a series of moderated small-group sessions in which the registered nurses jointly identified deficits in their work organisation, developed improvement measures, and then implemented and assessed them. Registered nurses of 22 wards actively took part in the small-group procedure. All nursing units jointly identified organisational deficits, developed possible improvement measures, and implemented them. The nursing teams then evaluated the implemented measures which were already assessable at the end of our research period; nearly all (99.0%) showed improvements, while 69.4% actually attained the desired goals. Participatory small-group activities may be successfully applied in hospital nursing in order to improve work organisation. Participatory assessment and redesign of nurses' work organisation should be integrated into regular team meetings. The nursing management should actively support the implementation process. © 2018 John Wiley & Sons Ltd.

  5. Redesigning fruit and vegetable distribution network in Tehran using a city logistics model

    Directory of Open Access Journals (Sweden)

    Farshad Saeedi

    2019-01-01

    Full Text Available Tehran, as one of the most populated capital cities worldwide, is categorized in the group of highly polluted cities in terms of the geographical location as well as increased number of industries, vehicles, domestic fuel consumption, intra-city trips, increased manufacturing units, and in general excessive increase in the consumption of fossil energies. City logistics models can be effectively helpful for solving the complicated problems of this city. In the present study, a queuing theory-based bi-objective mathematical model is presented, which aims to optimize the environmental and economic costs in city logistics operations. It also tries to reduce the response time in the network. The first objective is associated with all beneficiaries and the second one is applicable for perishable and necessary goods. The proposed model makes decisions on urban distribution centers location problem. Subsequently, as a case study, the fruit and vegetable distribution network of Tehran city is investigated and redesigned via the proposed modelling. The results of the implementation of the model through traditional and augmented ε-constraint methods indicate the efficiency of the proposed model in redesigning the given network.

  6. Redesigning a Ministry of Health's organizational structure: exploring implementation challenges through Botswana's experiences.

    Science.gov (United States)

    Seitio-Kgokgwe, Onalenna; Gauld, Robin D C; Hill, Philip C; Barnett, Pauline

    2016-04-01

    The Botswana's Ministry of Health redesigned and adopted a new organizational structure in 2005, which was poorly implemented. This article explores factors that influenced the implementation of this organizational structure. This article draws from data collected through in-depth interviews with 54 purposively selected key informants comprising policy makers, senior managers and staff of the Ministry of Health (N = 40) and senior officers from various stakeholder organizations (N = 14). Participants generally felt that the review of the Ministry of Health organizational structure was important. The previous structure was considered obsolete with fragmented functions that limited the overall performance of the health system. The new organizational structure was viewed to be aligned to current national priorities with potential to positively influence performance. Some key weaknesses identified included lack of consultation and information sharing with workers during the restructuring process, which affected the understanding of their new roles, failure to mobilize key resources to support implementation of the new structure and inadequate monitoring of the implementation process. Redesigning an organizational structure is a major change. There is a need for effective and sustained leadership to plan, direct, coordinate, monitor and evaluate the implementation phase of the reform. Copyright © 2014 John Wiley & Sons, Ltd. Copyright © 2014 John Wiley & Sons, Ltd.

  7. Ergonomi Function Deployment Pada Redesign Alat Parut Kelapa Untuk Ibu Rumah Tangga

    Directory of Open Access Journals (Sweden)

    Roberta Zulfhi Surya

    2014-10-01

    Abstract. Grate the coconut is one of kitchen activity which faces by housewife in daily life. A coconut grater product which is distibuted in market, one of them is manual crank system. Housewife complain that they feel painfull in their body, especially at hand. Waist and back after using available old tool. This research is purposed to improve the design of coconut grater with crank system by ergonomic function deployment (EFD approach, also to known mosculuskletal reducing of housewife as user and show differention time of grater after redesign done. Research was conducted in RT. 001 RW.005 Tembilahan, Indragiri Hilir District. Research model used treatment by subject design with total sample is 12 housewife which is calculation by Colton Formula. Improvement new coconut grater design with crank system which EFD got by creat the matrix house of ergonomic (HOE and determination of anthropometry data. Mosculuskletal complain on housewife is measured by making the Nordic Body Map (NBM Questionnaire work sheet. Time of grated the coconut got by testing coconut grater by crank system on before and after using. Research finding after redesign of coconut grater of crank system shown that design of coconut grater of crank system with EFD and base on ergonomic acpects (effective, confort, savety, healthy and efficient. Mosculuskletal complaint that happend on housewife decrease about 0,285 or 17,39%. Time of grate is also faster around 5 minutes or has imporove 30,1%.

  8. A University Web Portal redesign applying accessibility patterns. Breaking Down Barriers for Visually Impaired Users

    Directory of Open Access Journals (Sweden)

    Hernán Sosa

    2015-08-01

    Full Text Available Definitely, the WWW and ICTs have become the preferred media for the interaction between society and its citizens, and public and private organizations have today the possibility of deploying their activities through the Web. In particular, university education is a domain where the benefits of these technological resources can strongly contribute in caring for students. However, most university Web portals are inaccessible to their user community (students, professors, and non-teaching staff, between others, since these portals do not take into account the needs of people with different capabilities. In this work, we propose an accessibility pattern driven process to the redesign of university Web portals, aiming to break down barriers for visually impaired users. The approach is implemented to a real case study: the Web portal of Universidad Nacional de la Patagonia Austral (UNPA. The results come from applying accessibility recommendations and evaluation tools (automatic and manual from internationally recognized organizations, to both versions of the Web portal: the original and the redesign one.

  9. Innovation in ambulatory care: a collaborative approach to redesigning the health care workplace.

    Science.gov (United States)

    Johnson, Paula A; Bookman, Ann; Bailyn, Lotte; Harrington, Mona; Orton, Piper

    2011-02-01

    To improve the quality of patient care and work satisfaction of the physicians and staff at an ambulatory practice that had recently started an innovative model of clinical care for women. The authors used an inclusive process, collaborative interactive action research, to engage all physicians and staff members in assessing and redesigning their work environment. Based on key barriers to working effectively and integrating work and family identified in that process, a pilot project with new work practices and structures was developed, implemented, and evaluated. The work redesign process established cross-occupational care teams in specific clinical areas. Members of the teams built skills in assessing clinical operations in their practice areas, developed new levels of collaboration, and constructed new models of distributed leadership. The majority of participants reported an improvement in how their area functioned. Integrating work and family/personal life-particularly practices around flexible work arrangements-became an issue for team discussion and solutions, not a matter of individual accommodation by managers. By engaging the workforce, collaborative interactive action research can help achieve lasting change in the health care workplace and increase physicians' and staff members' work satisfaction. This "dual agenda" may be best achieved through a collaborative process where cross-occupational teams are responsible for workflow and outcomes and where the needs of patients and providers are integrated.

  10. Reactor core fuel management

    International Nuclear Information System (INIS)

    Silvennoinen, P.

    1976-01-01

    The subject is covered in chapters, entitled: concepts of reactor physics; neutron diffusion; core heat transfer; reactivity; reactor operation; variables of core management; computer code modules; alternative reactor concepts; methods of optimization; general system aspects. (U.K.)

  11. Nuclear reactor core catcher

    International Nuclear Information System (INIS)

    1977-01-01

    A nuclear reactor core catcher is described for containing debris resulting from an accident causing core meltdown and which incorporates a method of cooling the debris by the circulation of a liquid coolant. (U.K.)

  12. Seismic core shroud

    International Nuclear Information System (INIS)

    Puri, A.; Mullooly, J.F.

    1981-01-01

    A core shroud is provided, comprising: a coolant boundary, following the shape of the core boundary, for channeling the coolant through the fuel assemblies; a cylindrical band positioned inside the core barrel and surrounding the coolant boundary; and support members extending from the coolant boundary to the band, for transferring load from the coolant boundary to the band. The shroud may be assembled in parts using automated welding techniques, and it may be adjusted to fit the reactor core easily

  13. The Physical Activity and Redesigned Community Spaces (PARCS Study: Protocol of a natural experiment to investigate the impact of citywide park redesign and renovation

    Directory of Open Access Journals (Sweden)

    Terry T. K. Huang

    2016-11-01

    Full Text Available Abstract Background The built environment plays a critical role in promoting physical activity and health. The association between parks, as a key attribute of the built environment, and physical activity, however, remains inconclusive. This project leverages a natural experiment opportunity to assess the impact of the Community Parks Initiative (CPI, a citywide park redesign and renovation effort in New York City, on physical activity, park usage, psychosocial and mental health, and community wellbeing. Methods The project will use a longitudinal design with matched controls. Thirty intervention park neighborhoods are socio-demographically matched to 20 control park neighborhoods. The study will investigate whether improvements in physical activity, park usage, psychosocial and mental health, and community wellbeing are observed from baseline to 3 years post-renovation among residents in intervention vs. control neighborhoods. Discussion This study represents a rare opportunity to provide robust evidence to further our understanding of the complex relationship between parks and health. Findings will inform future investments in health-oriented urban design policies and offer evidence for addressing health disparities through built environment strategies.

  14. A multi-stage stochastic program for supply chain network redesign problem with price-dependent uncertain demands

    DEFF Research Database (Denmark)

    Fattahi, Mohammad; Govindan, Kannan; Keyvanshokooh, Esmaeil

    2018-01-01

    In this paper, we address a multi-period supply chain network redesign problem in which customer zones have price-dependent stochastic demand for multiple products. A novel multi-stage stochastic program is proposed to simultaneously make tactical decisions including products' prices and strategic...... redesign decisions. Existing uncertainty in potential demands of customer zones is modeled through a finite set of scenarios, described in the form of a scenario tree. The scenarios are generated using a Latin Hypercube Sampling method and then a forward scenario construction technique is employed...

  15. Core Values | NREL

    Science.gov (United States)

    Core Values Core Values NREL's core values are rooted in a safe and supportive work environment guide our everyday actions and efforts: Safe and supportive work environment Respect for the rights physical and social environment Integrity Maintain the highest standard of ethics, honesty, and integrity

  16. Sidewall coring shell

    Energy Technology Data Exchange (ETDEWEB)

    Edelman, Ya A; Konstantinov, L P; Martyshin, A N

    1966-12-12

    A sidewall coring shell consists of a housing and a detachable core catcher. The core lifter is provided with projections, the ends of which are situated in another plane, along the longitudinal axis of the lifter. The chamber has corresponding projections.

  17. Conversation with Meir Sternberg

    Directory of Open Access Journals (Sweden)

    Federico Pianzola

    2011-07-01

    Full Text Available Below are the videos of the interview recorded the 21st May 2011 in Fribourg (CH, in occasion of the first RRN conference. Conversation with Meir Sternberg. Part 1 of 8 - Narratology: classical and postclassical studies. Part 2 of 8 - The development of an original theoretical framework. Part 3 of 8 - Sternberg and Genette: different ways for the same problems. Part 4 of 8 - «There are no forms except in terms of functions». Part 5 of 8 - A life writing articles: so many papers and just four books. Part 6 of 8 - Two arguments against mimetical approaches to narrative. Part 7 of 8 - «Narrative is not given, it is a construct». Part 8 of 8 - The proteus principle. the many-to-many correspondence between forms and functions.

  18. Thermodynamics and energy conversion

    CERN Document Server

    Struchtrup, Henning

    2014-01-01

    This textbook gives a thorough treatment of engineering thermodynamics with applications to classical and modern energy conversion devices.   Some emphasis lies on the description of irreversible processes, such as friction, heat transfer and mixing, and the evaluation of the related work losses. Better use of resources requires high efficiencies, therefore the reduction of irreversible losses should be seen as one of the main goals of a thermal engineer. This book provides the necessary tools.   Topics include: car and aircraft engines,  including Otto, Diesel and Atkinson cycles, by-pass turbofan engines, ramjet and scramjet;  steam and gas power plants, including advanced regenerative systems, solar tower, and compressed air energy storage; mixing and separation, including reverse osmosis, osmotic powerplants, and carbon sequestration; phase equilibrium and chemical equilibrium, distillation, chemical reactors, combustion processes, and fuel cells; the microscopic definition of entropy.    The book i...

  19. Communal biomass conversion plants

    International Nuclear Information System (INIS)

    Holm-Nielsen, J.B.; Huntingford, S.; Halberg, N.

    1993-03-01

    The aim was to show the agricultural advantages of farmers being in connection with Communal Biogas Plant. Whether a more environmentally protectire distribution of plant nutrients from animal manure takes place through a biogas plants distribution system, whether the nitrogen in the digested slurry is better utilized and whether the connection results in slurry transportation-time reduction, are discussed. The average amount of nitrogen from animal manure used per hectare was reduced. The area of manure distribution was larger. The nitrogen efficiency was increased when using digested slurry and purchase of N mineral fertilizer decreased, resulting in considerable reduction in nitrogen leaching. The amount of slurry delivered to the local storage tanks was approximately 45 per cent of the total amount treated on the biogas plant. Conditions of manure transport improved greatly as this was now the responsibility of the communal biomass conversion plant administrators. (AB) (24 refs.)

  20. Power conversion technologies

    Energy Technology Data Exchange (ETDEWEB)

    Newton, M. A.

    1997-02-01

    The Power Conversion Technologies thrust area identifies and sponsors development activities that enhance the capabilities of engineering at Lawrence Livermore National Laboratory (LLNL) in the area of solid- state power electronics. Our primary objective is to be a resource to existing and emerging LLNL programs that require advanced solid-state power electronic technologies.. Our focus is on developing and integrating technologies that will significantly impact the capability, size, cost, and reliability of future power electronic systems. During FY-96, we concentrated our research efforts on the areas of (1) Micropower Impulse Radar (MIR); (2) novel solid-state opening switches; (3) advanced modulator technology for accelerators; (4) compact accelerators; and (5) compact pulse generators.

  1. Thermal-hydraulic characteristics of double flat core HCLWR

    International Nuclear Information System (INIS)

    Sugimoto, Jun; Iwamura, Takamichi; Okubo, Tsutomu; Murao, Yoshio

    1989-02-01

    A thermal-hydraulic characteristics of double flat core high conversion light water reactor (HCLWR) is described. The concept of flat core proposed by Ishiguro et al. is to achieve negative void reactivity coefficient in tight lattice core, and at the same time, high conversion ratio and high burnup can be obtainable. The proposed double flat core HCLWR, based on these physical advantages and the consideration of safety assurance, aims at efficient use of the pressure vessel space to produce comparable thermal output as current 3-loop PWRs. The present work revealed the following items concerning the thermalhydraulic feasibility of the double flat core HCLWR: (1) Main thermal-hydraulic parameters of the plant can be almost the same as current PWRs, showing the use of PWR standard components without major modifications except in core region. (2) Heat removal from the fuel rod in a steady operational condition has enough margin to the critical heat flux (CHF) limit, which is evaluated with the existing CHF correlations. (3) The calculation by REFLA code shows that the maximum cladding temperature in LOCA-reflood is estimated to be far lower than the licensing criteria. It is therefore considered that the proposed double flat core HCLWR is feasible from the point of thermal-hydraulics. Since the available data base has certain applicational limit to the very short core as the present double flat core HCLWR, further detailed assessment is required. (author)

  2. The Role of Conversation Policy in Carrying Out Agent Conversations

    International Nuclear Information System (INIS)

    Link, Hamilton E.; Phillips, Laurence R.

    1999-01-01

    Structured conversation diagrams, or conversation specifications, allow agents to have predictable interactions and achieve predefined information-based goals, but they lack the flexibility needed to function robustly in an unpredictable environment. We propose a mechanism that combines a typical conversation structure with a separately established policy to generate an actual conversation. The word ''policy'' connotes a high-level direction external to a specific planned interaction with the environment. Policies, which describe acceptable procedures and influence decisions, can be applied to broad sets of activity. Based on their observation of issues related to a policy, agents may dynamically adjust their communication patterns. The policy object describes limitations, constraints, and requirements that may affect the conversation in certain circumstances. Using this new mechanism of interaction simplifies the description of individual conversations and allows domain-specific issues to be brought to bear more easily during agent communication. By following the behavior of the conversation specification when possible and deferring to the policy to derive behavior in exceptional circumstances, an agent is able to function predictably under normal situations and still act rationally in abnormal situations. Different conversation policies applied to a given conversation specification can change the nature of the interaction without changing the specification

  3. LMFBR design and its evolution. (2) Core design of LMFBR

    International Nuclear Information System (INIS)

    Uto, Nariaki; Mizuno, Tomoyasu

    2003-01-01

    Sodium-cooled core design studies are performed. MOX fuel core with axial blanket partial elimination subassembly due to safety consideration is studied. This type of core with high internal conversion ratio possesses capability of achieving 26 months of operation cycle length and 100 GWd/t of burnup averaged over core and blanket, which are superior characteristics in view of reducing cost of power generation. Metal fuel core is also studied, and its higher breeding capability reveals a potential of better core performance such as longer operation cycle length for the same level of electricity generation, though core outlet temperature is limited to lower level due to steel cladding-metal fuel compatibility concerns. Another metal fuel core concept using single Pu enrichment and two radial regions with individual fuel pin diameters achieves 550degC of core outlet temperature identical to that of MOX fuel core, keeping operation cycle length comparable with that of MOX fuel core. This series of study results show that sodium-cooled MOX and metal fuel cores have a high flexibility in satisfying various needs including fuel cycle cost and breeding capability, depending on the stage of introducing commercialized fast reactor cycle system. (author)

  4. Rotary core drills

    Energy Technology Data Exchange (ETDEWEB)

    1967-11-30

    The design of a rotary core drill is described. Primary consideration is given to the following component parts of the drill: the inner and outer tube, the core bit, an adapter, and the core lifter. The adapter has the form of a downward-converging sleeve and is mounted to the lower end of the inner tube. The lifter, extending from the adapter, is split along each side so that it can be held open to permit movement of a core. It is possible to grip a core by allowing the lifter to assume a closed position.

  5. Does a grill menu redesign influence sales, nutrients purchased, and consumer acceptance in a worksite cafeteria?

    Science.gov (United States)

    Vadiveloo, Maya K; Malik, Vasanti S; Spiegelman, Donna; Willett, Walter C; Mattei, Josiemer

    2017-12-01

    Worksite cafeterias are compelling venues to improve diet quality through environmental changes. We conducted a pre-post study to evaluate how a cafeteria-initiated grill menu redesign influenced sales, revenue, and nutrient content of foods purchased. Secondly, we evaluated consumer opinions about menu changes to inform practices for worksite environment interventions. Monthly sales data (2012-2015) were used to compute gross sales and revenue of entrées and side dishes pre-post menu changes. Alternative protein sources replaced red meat; nutrient composition and nutrients purchased were compared using Food Pro software. Consumer responses were queried using online surveys; open-ended responses were analyzed using NVivo. Differences in sales and nutrient content pre-post menu redesign were tested with Wilcoxon Rank Sum tests. Gross sales of entrées (61 vs. 222 servings/month; p = 0.01) and side dishes (120 vs. 365 servings/month; p = 0.001) increased more than three-fold post-menu changes. Revenue from entrées (312 vs. 1144 USD/month; p = 0.01) and side dishes (238 vs. 914 USD/month; p = 0.001) also increased; per entrée, consumers purchased significantly more unsaturated fat (5 g), and less saturated fat (3 g) and sodium (100 mg). For side dishes, they purchased fewer calories (48 kcal) and unsaturated fat (2.9 g), but more fiber (1.8 g), and sodium (260 mg). Four themes emerged from consumer responses: the importance of 1) variety, novelty, choice; 2) cost, affordability, value; 3) health; and 4) food quality, taste. Menu redesign can improve nutrient content, while also increasing sales and revenue. Multi-dimensional assessment of the nutritional, consumer, and retailer implications is desirable practice for enacting similar environmental changes.

  6. AN INTELLIGENT CONVERSATION AGENT FOR HEALTH CARE DOMAIN

    Directory of Open Access Journals (Sweden)

    K. Karpagam

    2014-04-01

    Full Text Available Human Computer Interaction is one of the pervasive application areas of computer science to develop with multimodal interaction for information sharings. The conversation agent acts as the major core area for developing interfaces between a system and user with applied AI for proper responses. In this paper, the interactive system plays a vital role in improving knowledge in the domain of health through the intelligent interface between machine and human with text and speech. The primary aim is to enrich the knowledge and help the user in the domain of health using conversation agent to offer immediate response with human companion feel.

  7. Paradoxical therapy in conversion disorder

    OpenAIRE

    ATAOĞLU, Ahmet

    1998-01-01

    Paradoxical therapy consists of suggesting that the patient intentionally engages in the unwanted behaviour, such as performing complusive ritual or bringing on a conversion attack. In this study paradoxical intention (PI) was used with to half of the patients with conversion disorders, while the other half were treated with diazepam in order to examine the efficiency of the PI versus diazepam in conversion disorder. Patients treated with PI appeared to have a greater improvement r...

  8. A systematic review of human factors and ergonomics (HFE)-based healthcare system redesign for quality of care and patient safety.

    Science.gov (United States)

    Xie, Anping; Carayon, Pascale

    2015-01-01

    Healthcare systems need to be redesigned to provide care that is safe, effective and efficient, and meets the multiple needs of patients. This systematic review examines how human factors and ergonomics (HFE) is applied to redesign healthcare work systems and processes and improve quality and safety of care. We identified 12 projects representing 23 studies and addressing different physical, cognitive and organisational HFE issues in a variety of healthcare systems and care settings. Some evidence exists for the effectiveness of HFE-based healthcare system redesign in improving process and outcome measures of quality and safety of care. We assessed risk of bias in 16 studies reporting the impact of HFE-based healthcare system redesign and found varying quality across studies. Future research should further assess the impact of HFE on quality and safety of care, and clearly define the mechanisms by which HFE-based system redesign can improve quality and safety of care.

  9. HYDRATE CORE DRILLING TESTS

    Energy Technology Data Exchange (ETDEWEB)

    John H. Cohen; Thomas E. Williams; Ali G. Kadaster; Bill V. Liddell

    2002-11-01

    The ''Methane Hydrate Production from Alaskan Permafrost'' project is a three-year endeavor being conducted by Maurer Technology Inc. (MTI), Noble, and Anadarko Petroleum, in partnership with the U.S. DOE National Energy Technology Laboratory (NETL). The project's goal is to build on previous and ongoing R&D in the area of onshore hydrate deposition. The project team plans to design and implement a program to safely and economically drill, core and produce gas from arctic hydrates. The current work scope includes drilling and coring one well on Anadarko leases in FY 2003 during the winter drilling season. A specially built on-site core analysis laboratory will be used to determine some of the physical characteristics of the hydrates and surrounding rock. Prior to going to the field, the project team designed and conducted a controlled series of coring tests for simulating coring of hydrate formations. A variety of equipment and procedures were tested and modified to develop a practical solution for this special application. This Topical Report summarizes these coring tests. A special facility was designed and installed at MTI's Drilling Research Center (DRC) in Houston and used to conduct coring tests. Equipment and procedures were tested by cutting cores from frozen mixtures of sand and water supported by casing and designed to simulate hydrate formations. Tests were conducted with chilled drilling fluids. Tests showed that frozen core can be washed out and reduced in size by the action of the drilling fluid. Washing of the core by the drilling fluid caused a reduction in core diameter, making core recovery very difficult (if not impossible). One successful solution was to drill the last 6 inches of core dry (without fluid circulation). These tests demonstrated that it will be difficult to capture core when drilling in permafrost or hydrates without implementing certain safeguards. Among the coring tests was a simulated hydrate

  10. Magnetohydrodynamic Convection in the Outer Core and its Geodynamic Consequences

    Science.gov (United States)

    Kuang, Weijia; Chao, Benjamin F.; Fang, Ming

    2004-01-01

    The Earth's fluid outer core is in vigorous convection through much of the Earth's history. In addition to generating and maintaining Earth s time-varying magnetic field (geodynamo), the core convection also generates mass redistribution in the core and a dynamical pressure field on the core-mantle boundary (CMB). All these shall result in various core-mantle interactions, and contribute to surface geodynamic observables. For example, electromagnetic core-mantle coupling arises from finite electrically conducting lower mantle; gravitational interaction occurs between the cores and the heterogeneous mantle; mechanical coupling may also occur when the CMB topography is aspherical. Besides changing the mantle rotation via the coupling torques, the mass-redistribution in the core shall produce a spatial-temporal gravity anomaly. Numerical modeling of the core dynamical processes contributes in several geophysical disciplines. It helps explain the physical causes of surface geodynamic observables via space geodetic techniques and other means, e.g. Earth's rotation variation on decadal time scales, and secular time-variable gravity. Conversely, identification of the sources of the observables can provide additional insights on the dynamics of the fluid core, leading to better constraints on the physics in the numerical modeling. In the past few years, our core dynamics modeling efforts, with respect to our MoSST model, have made significant progress in understanding individual geophysical consequences. However, integrated studies are desirable, not only because of more mature numerical core dynamics models, but also because of inter-correlation among the geophysical phenomena, e.g. mass redistribution in the outer core produces not only time-variable gravity, but also gravitational core-mantle coupling and thus the Earth's rotation variation. They are expected to further facilitate multidisciplinary studies of core dynamics and interactions of the core with other

  11. Sign Redesign: Applying Design Principles to Improve Signage in an Academic Library

    Directory of Open Access Journals (Sweden)

    Sheila Kasperek

    2014-05-01

    Full Text Available When the Mansfield University library’s Special Events and Customer Service Committee created a communications plan for the library, the opportunity presented itself to overhaul the library signs. Applying basic design principles of contrast, alignment, and repetition along with standards from the Americans with Disabilities Act, the library improved the visual communications within the library. Patrons can now read signs from a distance and understand their purpose. Using common design elements, the library began presenting official library information more cohesively. Extending beyond signs, these design principles are now part of the library’s print publications and promotional items. With this consistency, the library brand is more easily recognizable both within the library and across campus. This article describes some basic elements of design and the process of redesigning the signs.

  12. Medipix3RX: Characterizing the Medipix3 Redesign With Synchrotron Radiation

    CERN Document Server

    Gimenez, Eva N; Blaj, Gabriel; Campbell, Michael; Dolbnya, Igor; Frodjh, Erik; Horswell, Ian; Llopart, Xavier; Marchal, Julien; McGrath, John; Omar, David; Plackett, Richard; Sawhney, Kawal; Tartoni, Nicola

    2015-01-01

    The Medipix3RX is the latest version of the Medipix3 photon counting ASICs, which implements two new operational modes, with respect to the Medipix2 ASIC, aimed at eliminating charge shared events (referred to as Charge Summing Mode (CSM)) and at providing spectroscopic information (referred to as Colour Mode (CM)). The Medipix3RX is a redesign of the Medipix3v0 ASIC and corrects for the underperformance of CSM features observed in the previous version. This paper presents the results from synchrotron X-rays tests to evaluate the Medipix3RX ASIC performance. The newly implemented CSM algorithm eliminates the charge sharing effect at the same time as allocating the event to the readout pixel corresponding to the sensor pixel where the X-ray photon impinged. The new pixel trimming circuit led to a reduced dispersion between pixels. Further results of the linearity for all the gain modes, energy resolution and pixel uniformity are also presented.

  13. Space Shuttle Redesigned Solid Rocket Motor nozzle natural frequency variations with burn time

    Science.gov (United States)

    Lui, C. Y.; Mason, D. R.

    1991-01-01

    The effects of erosion and thermal degradation on the Space Shuttle Redesigned Solid Rocket Motor (RSRM) nozzle's structural dynamic characteristics were analytically evaluated. Also considered was stiffening of the structure due to internal pressurization. A detailed NASTRAN finite element model of the nozzle was developed and used to evaluate the influence of these effects at several discrete times during motor burn. Methods were developed for treating erosion and thermal degradation, and a procedure was developed to account for internal pressure stiffening using differential stiffness matrix techniques. Results were verified using static firing test accelerometer data. Fast Fourier Transform and Maximum Entropy Method techniques were applied to the data to generate waterfall plots which track modal frequencies with burn time. Results indicate that the lower frequency nozzle 'vectoring' modes are only slightly affected by erosion, thermal effects and internal pressurization. The higher frequency shell modes of the nozzle are, however, significantly reduced.

  14. Effectiveness of Toyota process redesign in reducing thyroid gland fine-needle aspiration error.

    Science.gov (United States)

    Raab, Stephen S; Grzybicki, Dana Marie; Sudilovsky, Daniel; Balassanian, Ronald; Janosky, Janine E; Vrbin, Colleen M

    2006-10-01

    Our objective was to determine whether the Toyota Production System process redesign resulted in diagnostic error reduction for patients who underwent cytologic evaluation of thyroid nodules. In this longitudinal, nonconcurrent cohort study, we compared the diagnostic error frequency of a thyroid aspiration service before and after implementation of error reduction initiatives consisting of adoption of a standardized diagnostic terminology scheme and an immediate interpretation service. A total of 2,424 patients underwent aspiration. Following terminology standardization, the false-negative rate decreased from 41.8% to 19.1% (P = .006), the specimen nondiagnostic rate increased from 5.8% to 19.8% (P Toyota process change led to significantly fewer diagnostic errors for patients who underwent thyroid fine-needle aspiration.

  15. [Proposing a physiological model for Emergency Department. Operating principles, classification of overcrowding and guidelines for redesign].

    Science.gov (United States)

    Herrera Carranza, M; Aguado Correa, F; Padilla Garrido, N; López Camacho, F

    2017-04-30

    The operation of Emergency Departments (ED) is determined by demand, their own organizational structures and the connection to other medical care levels. When these elements are not simultaneous, it hinders patient flow and decreases capacity, making it necessary to employ a systemic approach to the chain of emergency care as a single operational entity. With this theoretical orientation, we suggest a conceptual model similar to the physiological cardiac output, in which the preload is the demand, the contractile or flow pump is the organizational structure, the afterload is the hospital, the pre-ED valve is primary care and outpatient emergencies, and the post-ED valve is the diagnostic support services and the specialist consultants. Based on this theoretical approach we classify the different types of ED overcrowding and systematise its causes and the different waiting lists that it generates, which can help to redesign the service and avoid its saturation.

  16. The RCSB Protein Data Bank: redesigned web site and web services.

    Science.gov (United States)

    Rose, Peter W; Beran, Bojan; Bi, Chunxiao; Bluhm, Wolfgang F; Dimitropoulos, Dimitris; Goodsell, David S; Prlic, Andreas; Quesada, Martha; Quinn, Gregory B; Westbrook, John D; Young, Jasmine; Yukich, Benjamin; Zardecki, Christine; Berman, Helen M; Bourne, Philip E

    2011-01-01

    The RCSB Protein Data Bank (RCSB PDB) web site (http://www.pdb.org) has been redesigned to increase usability and to cater to a larger and more diverse user base. This article describes key enhancements and new features that fall into the following categories: (i) query and analysis tools for chemical structure searching, query refinement, tabulation and export of query results; (ii) web site customization and new structure alerts; (iii) pair-wise and representative protein structure alignments; (iv) visualization of large assemblies; (v) integration of structural data with the open access literature and binding affinity data; and (vi) web services and web widgets to facilitate integration of PDB data and tools with other resources. These improvements enable a range of new possibilities to analyze and understand structure data. The next generation of the RCSB PDB web site, as described here, provides a rich resource for research and education.

  17. Advancing Care Within an Adult Mental Health Day Hospital: Program Re-Design and Evaluation.

    Science.gov (United States)

    Taube-Schiff, Marlene; Mehak, Adrienne; Marangos, Sandy; Kalim, Anastasia; Ungar, Thomas

    2017-11-13

    Day hospital mental health programs provide alternate care to individuals of high acuity that do not require an inpatient psychiatric stay. Ensuring provision of best practice within these programs is essential for patient stabilization and recovery. However, there is scant literature to review when creating such a program. This paper provides an overview of the steps an acute care hospital took when designing and implementing new programming within a day hospital program. Qualitative data was collected following initial program rollout. This data helped to inform the ongoing modification of groups offered, group scheduling and content, as well as ensuring patient satisfaction and adequate skill delivery during the rollout period and beyond. The goal of this paper is to inform health service delivery for other programs when attempting to build or re-design a day hospital program.

  18. Reducing bending stress in external spur gears by redesign of the standard cutting tool

    DEFF Research Database (Denmark)

    Pedersen, Niels Leergaard

    2009-01-01

    For the design of gears the stress due to bending plays a significant role. The stress from bending is largest in the root of the gear teeth, and the magnitude of the maximum stress is controlled by the nominal bending stress and stress concentration due to the geometric shape of the tooth....... In this work the bending stress of involute teeth is minimized by shape optimizing the tip of the standard cutting tool. By redesign of the tip of the standard cutting tool we achieve that the functional part of the teeth stays the same while at the same time the root shape is changed so that a reduction...... of the stresses results. The tool tip shape is described by different parameterizations that use the super ellipse as the central shape. For shape optimization it is important that the shape is given analytically. The shape of the cut tooth that is the envelope of the cutting tool is found analytically...

  19. Sliding Mode Controller and Lyapunov Redesign Controller to Improve Microgrid Stability

    DEFF Research Database (Denmark)

    Hossain, Eklas; Perez, Ron; Padmanaban, Sanjeevikumar

    2017-01-01

    technique is used to enhance stability of microgrids. Besides adopting this technique here, Sliding Mode Controller (SMC) and Lyapunov Redesign Controller (LRC), two of the most prominent nonlinear control techniques, are individually implemented to control microgrid system stability with desired robustness....... CPL power is then varied to compare robustness of these two control techniques. This investigation revealed the better performance of the LRC system compared to SMC to retain stability in microgrid with dense CPL load. All the necessary results are simulated in Matlab/Simulink platform for authentic......To mitigate the microgrid instability despite the presence of dense Constant Power Load (CPL) loads in the system, a number of compensation techniques have already been gone through extensive research, proposed, and implemented around the world. In this paper, a storage based load side compensation...

  20. Construction and characterization of the redesigned PGAA facility at The University of Texas at Austin

    International Nuclear Information System (INIS)

    Revay, Zs.; Harrison, R.K.; Alvarez, E.; Biegalski, S.R.; Landsberger, S.

    2007-01-01

    The prompt gamma activation analysis (PGAA) facility at The University of Texas at Austin (UT) has been redesigned and reconstructed. As a result of the new shielding of the system, the neutron (at all energies) and gamma-ray backgrounds have been reduced by more than an order of magnitude, considerably improving the signal-to-noise ratio for the characteristic peaks. The prompt gamma peaks from the construction materials have also been decreased, providing better detection limits for elements. The calibration of the new system is shown in detail. All these efforts significantly improved the sensitivity and reliability of the chemical analyses performed in the facility. The characteristics of the improved PGAA system are also presented

  1. Redesigning and Manufacturing of a Land Levelling Shovel by Assembly Structural Stress Analysis

    Directory of Open Access Journals (Sweden)

    Tahir Altinbalik

    2014-02-01

    Full Text Available The aim was to redesign and manufacture of a shovel for a pull-type land levelling machine, which, in its present condition, is used to get easily damaged even under low loads. Firstly, the maximum pulling load affecting the levelling shovel was experimentally determined. Then, stable-shovel system with the bolt connection was replaced with a bearing-shaft connection system. In this way, the new shovel has gained a capability of making oscillation motion so that it can operate on sloped grounds. CATIA program was used in the design studies. The shovel system was investigated by assembly structural stress analyses. This new construction enabled the system to operate 3 times more securely at maximum stress conditions without changing the levelling shovel material. Thus, it is managed to prevent any possible damages that might occur due to maximum loading conditions of the system. Besides, displacements that occur on the shovel decreased at the rate of 90%.

  2. Digital redesign of anti-wind-up controller for cascaded analog system.

    Science.gov (United States)

    Chen, Y S; Tsai, J S H; Shieh, L S; Moussighi, M M

    2003-01-01

    The cascaded conventional anti-wind-up (CAW) design method for integral controller is discussed. Then, the prediction-based digital redesign methodology is utilized to find the new pulse amplitude modulated (PAM) digital controller for effective digital control of the analog plant with input saturation constraint. The desired digital controller is determined from existing or pre-designed CAW analog controller. The proposed method provides a novel methodology for indirect digital design of a continuous-time unity output-feedback system with a cascaded analog controller as in the case of PID controllers for industrial control processes with the presence of actuator saturations. It enables us to implement an existing or pre-designed cascaded CAW analog controller via a digital controller effectively.

  3. Robust digital controllers for uncertain chaotic systems: A digital redesign approach

    Energy Technology Data Exchange (ETDEWEB)

    Ababneh, Mohammad [Department of Controls, FMC Kongsberg Subsea, FMC Energy Systems, Houston, TX 77067 (United States); Barajas-Ramirez, Juan-Gonzalo [CICESE, Depto. De Electronica y Telecomunicaciones, Ensenada, BC, 22860 (Mexico); Chen Guanrong [Centre for Chaos Control and Synchronization, Department of Electronic Engineering, City University of Hong Kong (China); Shieh, Leang S. [Department of Electrical and Computer Engineering, University of Houston, Houston, TX 77204-4005 (United States)

    2007-03-15

    In this paper, a new and systematic method for designing robust digital controllers for uncertain nonlinear systems with structured uncertainties is presented. In the proposed method, a controller is designed in terms of the optimal linear model representation of the nominal system around each operating point of the trajectory, while the uncertainties are decomposed such that the uncertain nonlinear system can be rewritten as a set of local linear models with disturbed inputs. Applying conventional robust control techniques, continuous-time robust controllers are first designed to eliminate the effects of the uncertainties on the underlying system. Then, a robust digital controller is obtained as the result of a digital redesign of the designed continuous-time robust controller using the state-matching technique. The effectiveness of the proposed controller design method is illustrated through some numerical examples on complex nonlinear systems--chaotic systems.

  4. Ergonomics evaluation as a powerful tool to redesign advanced interfaces of nuclear control rooms

    International Nuclear Information System (INIS)

    Santos, Isaac J.A.L. dos; Carvalho, Paulo V.R.; Oliveira, Mauro V.; Fernandes, Nelson; Oliveira, Helio C.L.; Grecco, Claudio H.S.; Mol, Antonio C.A.; Augusto, Silas C.; Teixeira, Douglas V.; Ferraz, Fernando T.

    2007-01-01

    Ergonomics is the scientific discipline concerned with the understanding of interactions among humans and other elements of a system. Ergonomics contributes to the design and evaluation of tasks, jobs, products, environments and systems in order to make them compatible with the needs, abilities and limitations of people. In the safe operation of nuclear power plant the performance of the control room crews plays an important role. In this respect, well-designed human-system interfaces (HSI) are crucial for safe and efficient operation of the plant, reducing the occurrence of incidents, accidents and the risks for human error. The aim of this paper is to describe a case study in which a methodological framework was applied to redesign advanced interfaces of a nuclear simulator. (author)

  5. Redesign of the low energy section of the Fermilab linac to improve beam brightness

    International Nuclear Information System (INIS)

    Schmidt, C.; Noble, R.; Palkovic, J.; Mills, F.E.

    1988-10-01

    The critical parameters which limit the luminosity of the Fermilab Tevatron Collider are the beam emittances, both longitudinal and transverse, at each stage in the acceleration sequence. Improvements to reduce invariant emittance growth at earlier acceleration stages necessarily encourage improvements in all downstream stages. Recent advances in linac technology should permit a significant increase in the beam brightness of the Fermilab linac. A redesign of the low energy section of the linac is envisioned to include a circular aperture H/sup /minus// source, a short 30-keV transport line (solenoids, Gabor lenses or einzel lenses) for matching to a radio frequency quadrupole linac (RFQ), and injection at approximately 2 MeV into a new 200 MHz Alvarez linac tank for acceleration to 10 MeV. 9 refs., 1 fig

  6. Innovative use of technologies and methods to redesign care: the problem of care transitions.

    Science.gov (United States)

    Richman, Mark; Sklaroff, Laura Myerchin; Hoang, Khathy; Wasson, Elijah; Gross-Schulman, Sandra

    2014-01-01

    Organizations are redesigning models of care in today's rapidly changing health care environment. Using proven innovation techniques maximizes likelihood of effective change. Our safety-net hospital aims to reduce high emergency department visit, admission, and readmission rates, key components to health care cost control. Twenty-five clinical stakeholders participated in mixed-methods innovation exercises to understand stakeholders, frame problems, and explore solutions. We identified existing barriers and means to improve post-emergency department/post-inpatient discharge care coordination/communication among patient-centered medical home care team members, including patients. Physicians and staff preferred automated e-mail notifications, including patient identifiers, medical home/primary care provider information, and relevant clinical documentation, to improve communication efficiency/efficacy.

  7. Participatory ergonomic intervention for prevention of low back pain: assembly line redesign case.

    Science.gov (United States)

    Bernardes, João Marcos; Wanderck, Claudia; Moro, Antônio Renato Pereira

    2012-01-01

    This paper gives an overview of a participatory ergonomic intervention aimed at reducing low back pain cases in the dispatch department of a catalogue and e-commerce retail company. Based on the findings of the ergonomic analysis and design committee, the company's own employees redesigned the assembly line's layout. As a result of these changes two job tasks that involved manual material handling of boxes, identified by the revised NIOSH equation as posing an increased risk for lifting-related low back pain, were totally eliminated, and the employees responsible for moving boxes from the end of the assembly line to pallets on the ground were given more control over their jobs, and these jobs were also enriched with a new, less heavy task. These results demonstrate that participatory ergonomic interventions are a viable and effective strategy to reduce the exposure to work-related physical and psychosocial risk factors for low back pain.

  8. Thermal hydraulic model validation for HOR mixed core fuel management

    International Nuclear Information System (INIS)

    Gibcus, H.P.M.; Vries, J.W. de; Leege, P.F.A. de

    1997-01-01

    A thermal-hydraulic core management model has been developed for the Hoger Onderwijsreactor (HOR), a 2 MW pool-type university research reactor. The model was adopted for safety analysis purposes in the framework of HEU/LEU core conversion studies. It is applied in the thermal-hydraulic computer code SHORT (Steady-state HOR Thermal-hydraulics) which is presently in use in designing core configurations and for in-core fuel management. An elaborate measurement program was performed for establishing the core hydraulic characteristics for a variety of conditions. The hydraulic data were obtained with a dummy fuel element with special equipment allowing a.o. direct measurement of the true core flow rate. Using these data the thermal-hydraulic model was validated experimentally. The model, experimental tests, and model validation are discussed. (author)

  9. Redesigning the Production of the Bacillus thuringiensis Bio-Pesticide within the Context of Subsistence Agriculture in Andhra Pradesh, India

    NARCIS (Netherlands)

    Puente, D.

    2007-01-01

    Biotechnologies are social constructions. The way in which biotechnology is designed, developed and deployed depends on the actors involved in these processes and the strategies and choices employed by these actors. This article assesses the re-designing process of the production of a biopesticide

  10. Effect of a redesigned two-wheeled container for refuse collecting on mechanical loading of low back and shoulders

    NARCIS (Netherlands)

    Kuijer, P. Paul F. M.; Hoozemans, Marco J. M.; Kingma, Idsart; van Dieën, Jaap H.; de Vries, Wiebe H. K.; Veeger, Dirk Jan; van der Beek, Allard J.; Visser, Bart; Frings-Dresen, Monique H. W.

    2003-01-01

    The objective of this study was to compare the mechanical and perceived workload when working with a redesigned two-wheeled container and working with a standard two-wheeled container for refuse collecting. The three changes in the design of the container were a displacement of the position of the

  11. Creating an Environment Conducive to Active and Collaborative Learning: Redesigning Introduction to Sociology at a Large Research University

    Science.gov (United States)

    Lo, C. C.; Prohaska, A.

    2011-01-01

    In 2003 a Southeastern research university undertook the redesign of an introductory sociology course in order to improve student success by adding active and collaborative learning activities that gave students greater responsibility for learning. The new "hybrid" course provides most course materials online, requires electronic…

  12. Redesigning a control room from an ergonomic point of view : a case study of user participation in a chemical plant

    NARCIS (Netherlands)

    Schaaf, van der T.W.; Kragt, H.; Kragt, H.

    1992-01-01

    A field study in a chemical industry was conducted to redesign a control room with panel instrumentation into one with visual display units (VDUs). The authors had been asked to advise the project team and to participate in the application. First, a general evaluation of the central control room

  13. Flipping the Classroom Applications to Curriculum Redesign for an Introduction to Management Course: Impact on Grades

    Science.gov (United States)

    Albert, Michael; Beatty, Brian J.

    2014-01-01

    The authors discuss the application of the flipped classroom model to the redesign of an introduction to management course at a highly diverse, urban, Association to Advance Collegiate Schools of Business-accredited U.S. university. The author assessed the impact of a flipped classroom versus a lecture class on grades. Compared to the prior…

  14. Analisis Karakteristik Traksi Serta Redesign Rasio Transmisi Mobil Toyota Fortuner 4.0 V6 Sr (At 4x4

    Directory of Open Access Journals (Sweden)

    Nico Yudha Wardana

    2017-01-01

    Full Text Available Produksi mobil Indonesia tahun 2014 mengalami peningkatan sebanyak 1,29 juta unit, meningkat 7,5 persen dari tahun sebelumnya dan terus mengalami peningkatan pada tahun 2015 sebesar 2 juta unit (Kemenprin, 1/16. Tingginya penjualan mobil tersebut tidak diiringi dengan upaya produsen untuk mencerdaskan konsumen mengenai performa mobil. Hal tersebut yang mendasari penulis untuk melakukan analisa karakteristik traksi pada mobil Toyota fortuner 4.0 V6 SR (4X4 AT. Dalam penelitian ini, telah dilakukan tiga tahapan pengujian. Tahapan pertama adalah melakukan pengujian dynotest pada mobil untuk mengetehaui efisiensi transmisi. Tahap kedua, dilakukan analisa perhitungan sehingga di dapatkan grafik karakteristik mobil pada kondisi standar. Selanjutnya tahap ketiga dilakukan evaluasi terhadap grafik karakteristik traksi mobil standar, dilanjutkan dengan proses redesign tingkat transmisi untuk mengoptimalkan kinerja mobil menggunakan metode progressi geometri. Dari penelitian ini diperoleh grafik karakteristik traksi mobil untuk kondisi rasio gigi standar serta hasil redesign dengan 5,6 dan 7 tingkat kecepatan. Setelah dilakukan analisa, ternyata distribusi traksi pada mobil kondisistandar tidak merata, terdapat loses yang cukup besar terutama pada 3 tingkatan gigi awal. Hasil redesign dengan menggunakan teori progressi geometry menunjukan distribusi traksi yang lebih baik dari kondisi standar. Loses traksi untuk perpindahan gigi pertama menuju tingkat gigi kedua yang awalnya pada kondisi standar sebesar 4.564 kN dapat diminimalisir sampai dengan 1 kN setelah dilakukan redesign dengan 7 tingkat kecepatan.

  15. Linking Teacher Education to Redesigned Systems of Accountability: A Call for Multiple Measures in Pre-Service Teacher Effectiveness

    Science.gov (United States)

    Farley, Amy N.; Clayton, Grant; Kaka, Sarah J.

    2018-01-01

    In this written commentary for the special issue of "Education Policy Analysis Archives" focused on "Redesigning Assessment and Accountability," we call for teacher preparation to embrace a multiple measures philosophy by providing teacher candidates with rich opportunities to engage with data from a variety of sources, beyond…

  16. Redesigning Schools to Reach Every Student with Excellent Teachers: Change Management--Key Theories to Consider when Extending Reach

    Science.gov (United States)

    Barrett, Sharon Kebschull

    2012-01-01

    As schools, their teachers, and outside facilitators redesign jobs and incorporate technology to extend the reach of excellent teachers to more students and develop an Opportunity Culture for all, choosing the right school models is just one part of the task. The human experience--and experience in education--says that even perfect design will not…

  17. Hospital's redesigned Web site patient-friendly, comprehensive. Site one-of-a-kind in Twin Cities market area.

    Science.gov (United States)

    Rees, T

    2001-01-01

    North Memorial Medical Center, Robbinsdale, Minn., has opened a brightly redesigned Web site. It is patient-friendly and features a different approach to provide healthcare information called "care areas," which are organized by condition, such as heart care, cancer care and childbirth. This approach led to the the site being named North Memorial Online Care Center.

  18. Sustaining the work ability and work motivation of lower-educated older workers: Directions for work redesign

    NARCIS (Netherlands)

    Sanders, J.; Dorenbosch, L.; Grundemann, R.; Blonk, R.W.B.

    2011-01-01

    This study examines directions for work redesign which might lead to the creation of sustainable jobs for lower-educated older workers (45 years or over, ISCED 0-2) and thus motivate and enable them to extend their working lives. We use longitudinal data on 1,264 older Dutch workers collected by the

  19. A Journey to Improved Inpatient Glycemic Control by Redesigning Meal Delivery and Insulin Administration.

    Science.gov (United States)

    Engle, Martha; Ferguson, Allison; Fields, Willa

    2016-01-01

    The purpose of this quality improvement project was to redesign a hospital meal delivery process in order to shorten the time between blood glucose monitoring and corresponding insulin administration and improve glycemic control. This process change redesigned the workflow of the dietary and nursing departments. Modifications included nursing, rather than dietary, delivering meal trays to patients receiving insulin. Dietary marked the appropriate meal trays and phoned each unit prior to arrival on the unit. The process change was trialed on 2 acute care units prior to implementation hospital wide. Elapsed time between blood glucose monitoring and insulin administration was analyzed before and after process change as well as evaluation of glucometrics: percentage of patients with blood glucose between 70 and 180 mg/dL (percent perfect), blood glucose greater than 300 mg/dL (extreme hyperglycemia), and blood glucose less than 70 mg/dL (hypoglycemia). Percent perfect glucose results improved from 45% to 53%, extreme hyperglycemia (blood glucose >300 mg/dL) fell from 11.7% to 5%. Hypoglycemia demonstrated a downward trend line, demonstrating that with improving glycemic control hypoglycemia rates did not increase. Percentage of patients receiving meal insulin within 30 minutes of blood glucose check increased from 35% to 73%. In the hospital, numerous obstacles were present that interfered with on-time meal insulin delivery. Establishing a meal delivery process with the nurse performing the premeal blood glucose check, delivering the meal, and administering the insulin improves overall blood glucose control. Nurse-led process improvement of blood glucose monitoring, meal tray delivery, and insulin administration does lead to improved glycemic control for the inpatient population.

  20. Redesigning a joint replacement program using Lean Six Sigma in a Veterans Affairs hospital.

    Science.gov (United States)

    Gayed, Benjamin; Black, Stephen; Daggy, Joanne; Munshi, Imtiaz A

    2013-11-01

    In April 2009, an analysis of joint replacement surgical procedures at the Richard L. Roudebush Veterans Affairs Medical Center, Indianapolis, Indiana, revealed that total hip and knee replacements incurred $1.4 million in non-Veterans Affairs (VA) care costs with an average length of stay of 6.1 days during fiscal year 2008. The Joint Replacement Program system redesign project was initiated following the Vision-Analysis-Team-Aim-Map-Measure-Change-Sustain (VA-TAMMCS) model to increase efficiency, decrease length of stay, and reduce non-VA care costs. To determine the effectiveness of Lean Six Sigma process improvement methods applied in a VA hospital. Perioperative processes for patients undergoing total joint replacement were redesigned following the VA-TAMMCS model--the VA's official, branded method of Lean Six Sigma process improvement. A multidisciplinary team including the orthopedic surgeons, frontline staff, and executive management identified waste in the current processes and initiated changes to reduce waste and increase efficiency. Data collection included a 1-year baseline period and a 20-month sustainment period. The primary endpoint was length of stay; a secondary analysis considered non-VA care cost reductions. Length of stay decreased 36% overall, decreasing from 5.3 days during the preproject period to 3.4 days during the 20-month sustainment period (P Lean and Six Sigma process improvement initiatives in a surgical practice, producing a 36% sustained reduction in length of stay and completely eliminating non-VA care for total hip and knee replacements while increasing total joint replacement volume at this medical center.