WorldWideScience

Sample records for conversion alternatives study

  1. Energy conversion alternatives study

    Science.gov (United States)

    Shure, L. T.

    1979-01-01

    Comparison of coal based energy systems is given. Study identifies and compares various advanced energy conversion systems using coal or coal derived fuels for baselaoad electric power generation. Energy Conversion Alternatives Study (ECAS) reports provede government, industry, and general public with technically consistent basis for comparison of system's options of interest for fossilfired electric-utility application.

  2. Energy Conversion Alternatives Study (ECAS)

    Science.gov (United States)

    1977-01-01

    ECAS compared various advanced energy conversion systems that can use coal or coal-derived fuels for baseload electric power generation. It was conducted in two phases. Phase 1 consisted of parametric studies. From these results, 11 concepts were selected for further study in Phase 2. For each of the Phase 2 systems and a common set of ground rules, performance, cost, environmental intrusion, and natural resource requirements were estimated. In addition, the contractors defined the state of the associated technology, identified the advances required, prepared preliminary research and development plans, and assessed other factors that would affect the implementation of each type of powerplant. The systems studied in Phase 2 include steam systems with atmospheric- and pressurized-fluidized-bed boilers; combined cycle gas turbine/steam systems with integrated gasifiers or fired by a semiclean, coal derived fuel; a potassium/steam system with a pressurized-fluidized-bed boiler; a closed-cycle gas turbine/organic system with a high-temperature, atmospheric-fluidized-bed furnace; a direct-coal-fired, open- cycle magnetohydrodynamic/steam system; and a molten-carbonate fuel cell/steam system with an integrated gasifier. The sensitivity of the results to changes in the ground rules and the impact of uncertainties in capital cost estimates were also examined.

  3. Alternative Payment Models Should Risk-Adjust for Conversion Total Hip Arthroplasty: A Propensity Score-Matched Study.

    Science.gov (United States)

    McLawhorn, Alexander S; Schairer, William W; Schwarzkopf, Ran; Halsey, David A; Iorio, Richard; Padgett, Douglas E

    2017-12-06

    For Medicare beneficiaries, hospital reimbursement for nonrevision hip arthroplasty is anchored to either diagnosis-related group code 469 or 470. Under alternative payment models, reimbursement for care episodes is not further risk-adjusted. This study's purpose was to compare outcomes of primary total hip arthroplasty (THA) vs conversion THA to explore the rationale for risk adjustment for conversion procedures. All primary and conversion THAs from 2007 to 2014, excluding acute hip fractures and cancer patients, were identified in the National Surgical Quality Improvement Program database. Conversion and primary THA patients were matched 1:1 using propensity scores, based on preoperative covariates. Multivariable logistic regressions evaluated associations between conversion THA and 30-day outcomes. A total of 2018 conversions were matched to 2018 primaries. There were no differences in preoperative covariates. Conversions had longer operative times (148 vs 95 minutes, P reimbursement models shift toward bundled payment paradigms, conversion THA appears to be a procedure for which risk adjustment is appropriate. Copyright © 2017 Elsevier Inc. All rights reserved.

  4. Energy Conversion Alternatives Study (ECAS), General Electric Phase 1. Volume 3: Energy conversion subsystems and components. Part 1: Bottoming cycles and materials of construction

    Science.gov (United States)

    Shah, R. P.; Solomon, H. D.

    1976-01-01

    Energy conversion subsystems and components were evaluated in terms of advanced energy conversion systems. Results of the bottoming cycles and materials of construction studies are presented and discussed.

  5. Cogeneration Technology Alternatives Study (CTAS). Volume 3: Energy conversion system characteristics

    Science.gov (United States)

    1980-01-01

    Six current and thirty-six advanced energy conversion systems were defined and combined with appropriate balance of plant equipment. Twenty-six industrial processes were selected from among the high energy consuming industries to serve as a frame work for the study. Each conversion system was analyzed as a cogenerator with each industrial plant. Fuel consumption, costs, and environmental intrusion were evaluated and compared to corresponding traditional values. The advanced energy conversion technologies indicated reduced fuel consumption, costs, and emissions. Fuel energy savings of 10 to 25 percent were predicted compared to traditional on site furnaces and utility electricity. With the variety of industrial requirements, each advanced technology had attractive applications. Fuel cells indicated the greatest fuel energy savings and emission reductions. Gas turbines and combined cycles indicated high overall annual savings. Steam turbines and gas turbines produced high estimated returns. In some applications, diesels were most efficient. The advanced technologies used coal derived fuels, or coal with advanced fluid bed combustion or on site gasifications. Data and information for both current and advanced energy conversion technology are presented. Schematic and physical descriptions, performance data, equipment cost estimates, and predicted emissions are included. Technical developments which are needed to achieve commercialization in the 1985-2000 period are identified.

  6. Information for Consumers about Alternative Fuel Conversions

    Science.gov (United States)

    Here are some factors to be aware of if you are considering fuel conversion, including background information on fuel conversion, instructions for demonstrating compliance, and other related information.

  7. Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 5: Combined gas-steam turbine cycles. [energy conversion efficiency in electric power plants

    Science.gov (United States)

    Amos, D. J.; Foster-Pegg, R. W.; Lee, R. M.

    1976-01-01

    The energy conversion efficiency of gas-steam turbine cycles was investigated for selected combined cycle power plants. Results indicate that it is possible for combined cycle gas-steam turbine power plants to have efficiencies several point higher than conventional steam plants. Induction of low pressure steam into the steam turbine is shown to improve the plant efficiency. Post firing of the boiler of a high temperature combined cycle plant is found to increase net power but to worsen efficiency. A gas turbine pressure ratio of 12 to 1 was found to be close to optimum at all gas turbine inlet temperatures that were studied. The coal using combined cycle plant with an integrated low-Btu gasifier was calculated to have a plant efficiency of 43.6%, a capitalization of $497/kW, and a cost of electricity of 6.75 mills/MJ (24.3 mills/kwh). This combined cycle plant should be considered for base load power generation.

  8. 75 FR 29605 - Clean Alternative Fuel Vehicle and Engine Conversions

    Science.gov (United States)

    2010-05-26

    ... Part II Environmental Protection Agency 40 CFR Parts 85 and 86 Clean Alternative Fuel Vehicle and...-0299; FRL-9149-9] RIN 2060-AP64 Clean Alternative Fuel Vehicle and Engine Conversions AGENCY... streamline the process by which manufacturers of clean alternative fuel conversion systems may demonstrate...

  9. Energy Conversion Alternatives Study (ECAS), General Electric Phase 1. Volume 2: Advanced energy conversion systems. Part 1: Open-cycle gas turbines

    Science.gov (United States)

    Brown, D. H.; Corman, J. C.

    1976-01-01

    Ten energy conversion systems are defined and analyzed in terms of efficiency. These include: open-cycle gas turbine recuperative; open-cycle gas turbine; closed-cycle gas turbine; supercritical CO2 cycle; advanced steam cycle; liquid metal topping cycle; open-cycle MHD; closed-cycle inert gas MHD; closed-cycle liquid metal MHD; and fuel cells. Results are presented.

  10. Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 1: Introduction and summary and general assumptions. [energy conversion systems for electric power plants using coal - feasibility

    Science.gov (United States)

    Beecher, D. T.

    1976-01-01

    Nine advanced energy conversion concepts using coal or coal-derived fuels are summarized. They are; (1) open-cycle gas turbines, (2) combined gas-steam turbine cycles, (3) closed-cycle gas turbines, (4) metal vapor Rankine topping, (5) open-cycle MHD; (6) closed-cycle MHD; (7) liquid-metal MHD; (8) advanced steam; and (9) fuel cell systems. The economics, natural resource requirements, and performance criteria for the nine concepts are discussed.

  11. Energy Conversion Alternatives Study (ECAS), General Electric Phase 1. Volume 3: Energy conversion subsystems and components. Part 3: Gasification, process fuels, and balance of plant

    Science.gov (United States)

    Boothe, W. A.; Corman, J. C.; Johnson, G. G.; Cassel, T. A. V.

    1976-01-01

    Results are presented of an investigation of gasification and clean fuels from coal. Factors discussed include: coal and coal transportation costs; clean liquid and gas fuel process efficiencies and costs; and cost, performance, and environmental intrusion elements of the integrated low-Btu coal gasification system. Cost estimates for the balance-of-plant requirements associated with advanced energy conversion systems utilizing coal or coal-derived fuels are included.

  12. Energy Conversion Alternatives Study (ECAS), General Electric Phase 1. Volume 1: Executive summary. [using coal or coal derived fuels

    Science.gov (United States)

    Corman, J. C.

    1976-01-01

    A data base for the comparison of advanced energy conversion systems for utility applications using coal or coal-derived fuels was developed. Estimates of power plant performance (efficiency), capital cost, cost of electricity, natural resource requirements, and environmental intrusion characteristics were made for ten advanced conversion systems. Emphasis was on the energy conversion system in the context of a base loaded utility power plant. All power plant concepts were premised on meeting emission standard requirements. A steam power plant (3500 psig, 1000 F) with a conventional coal-burning furnace-boiler was analyzed as a basis for comparison. Combined cycle gas/steam turbine system results indicated competitive efficiency and a lower cost of electricity compared to the reference steam plant. The Open-Cycle MHD system results indicated the potential for significantly higher efficiency than the reference steam plant but with a higher cost of electricity.

  13. Alternative Fuels Data Center: Conversion Regulations

    Science.gov (United States)

    . Conversion systems must meet the same emissions standards that gasoline or diesel products do. Refer to EPA's manufacturer that holds the relevant emissions-related certifications and tampering exemptions. New and

  14. Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 7: Metal vapor Rankine topping-steam bottoming cycles. [energy conversion efficiency in electric power plants

    Science.gov (United States)

    Deegan, P. B.

    1976-01-01

    Adding a metal vapor Rankine topper to a steam cycle was studied as a way to increase the mean temperature at which heat is added to the cycle to raise the efficiency of an electric power plant. Potassium and cesium topping fluids were considered. Pressurized fluidized bed or pressurized (with an integrated low-Btu gasifier) boilers were assumed. Included in the cycles was a pressurizing gas turbine with its associated recuperator, and a gas economizer and feedwater heater. One of the ternary systems studied shows plant efficiency of 42.3% with a plant capitalization of $66.7/kW and a cost of electricity of 8.19 mills/MJ (29.5 mills/kWh).

  15. Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 6: Closed-cycle gas turbine systems. [energy conversion efficiency in electric power plants

    Science.gov (United States)

    Amos, D. J.; Fentress, W. K.; Stahl, W. F.

    1976-01-01

    Both recuperated and bottomed closed cycle gas turbine systems in electric power plants were studied. All systems used a pressurizing gas turbine coupled with a pressurized furnace to heat the helium for the closed cycle gas turbine. Steam and organic vapors are used as Rankine bottoming fluids. Although plant efficiencies of over 40% are calculated for some plants, the resultant cost of electricity was found to be 8.75 mills/MJ (31.5 mills/kWh). These plants do not appear practical for coal or oil fired plants.

  16. Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 11: Advanced steam systems. [energy conversion efficiency for electric power plants using steam

    Science.gov (United States)

    Wolfe, R. W.

    1976-01-01

    A parametric analysis was made of three types of advanced steam power plants that use coal in order to have a comparison of the cost of electricity produced by them a wide range of primary performance variables. Increasing the temperature and pressure of the steam above current industry levels resulted in increased energy costs because the cost of capital increased more than the fuel cost decreased. While the three plant types produced comparable energy cost levels, the pressurized fluidized bed boiler plant produced the lowest energy cost by the small margin of 0.69 mills/MJ (2.5 mills/kWh). It is recommended that this plant be designed in greater detail to determine its cost and performance more accurately than was possible in a broad parametric study and to ascertain problem areas which will require development effort. Also considered are pollution control measures such as scrubbers and separates for particulate emissions from stack gases.

  17. Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 9: Closed-cycle MHD. [energy conversion efficiency of electric power plants using magnetohydrodynamics

    Science.gov (United States)

    Tsu, T. C.

    1976-01-01

    A closed-cycle MHD system for an electric power plant was studied. It consists of 3 interlocking loops, an external heating loop, a closed-cycle cesium seeded argon nonequilibrium ionization MHD loop, and a steam bottomer. A MHD duct maximum temperature of 2366 K (3800 F), a pressure of 0.939 MPa (9.27 atm) and a Mach number of 0.9 are found to give a topping cycle efficiency of 59.3%; however when combined with an integrated gasifier and optimistic steam bottomer the coal to bus bar efficiency drops to 45.5%. A 1978 K (3100 F) cycle has an efficiency of 55.1% and a power plant efficiency of 42.2%. The high cost of the external heating loop components results in a cost of electricity of 21.41 mills/MJ (77.07 mills/kWh) for the high temperature system and 19.0 mills/MJ (68.5 mills/kWh) for the lower temperature system. It is, therefore, thought that this cycle may be more applicable to internally heated systems such as some futuristic high temperature gas cooled reactor.

  18. Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 12: Fuel cells. [energy conversion efficiency of, for use in electric power plants

    Science.gov (United States)

    Warde, C. J.; Ruka, R. J.; Isenberg, A. O.

    1976-01-01

    A parametric assessment of four fuel cell power systems -- based on phosphoric acid, potassium hydroxide, molten carbonate, and stabilized zirconia -- has shown that the most important parameters for electricity-cost reduction and/or efficiency improvement standpoints are fuel cell useful life and power density, use of a waste-heat recovery system, and fuel type. Typical capital costs, overall energy efficiencies (based on the heating value of the coal used to produce the power plant fuel), and electricity costs are: phosphoric acid $350-450/kWe, 24-29%, and 11.7 to 13.9 mills/MJ (42 to 50 mills/kWh); alkaline $450-700/kWe, 26-31%, and 12.8 to 16.9 mills/MJ (46 to 61 mills/kWh); molten carbonate $480-650/kWe, 32-46%, and 10.6 to 19.4 mills/MJ (38 to 70 mills/kWh), stabilized zirconia $420-950/kWe, 26-53%, and 9.7 to 16.9 mills/MJ (35 to 61 mills/kWh). Three types of fuel cell power plants -- solid electrolytic with steam bottoming, molten carbonate with steam bottoming, and solid electrolyte with an integrated coal gasifier -- are recommended for further study.

  19. The Nanticoke conversion study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-04-01

    A study was conducted to assess the conversion of the Nanticoke coal-fired power plant to cleaner burning natural gas combined-cycle gas turbines. The Nanticoke Generating Station on Lake Erie is responsible for more than 50 per cent of Ontario Power Generation's (OPG) coal-fired electricity production. The OPG is proposing to work towards compliance with the newly signed Ozone Annex to the 1991 Canada-United States Air Quality Agreement which will require fossil-fueled power plants in southern Ontario to reduce their smog-causing nitrogen oxides emissions by about 50 per cent by 2007. This study assessed the emission reduction benefits and financial costs of conversion compared to continuing to operate Nanticoke as a coal-fired plant. The analysis includes a base case set of data on fuel prices, retrofit costs, fuel efficiencies, annual capacity factors and other parameters. It was determined that conversion would cost the average household less than $3 per month on their electricity bill. Conversion would also reduce emissions nitrogen oxide, a major smog pollutant, by 83 per cent and the particulates that form the most health-threatening portion of smog would be reduced by 100 per cent. 15 tabs., 1 fig.

  20. Heat conversion alternative petrochemical complexes efficiency

    Science.gov (United States)

    Mrakin, A. N.; Selivanov, A. A.; Morev, A. A.; Batrakov, P. A.; Kulbyakina, A. V.; Sotnikov, D. G.

    2017-08-01

    The paper presents the energy and economic efficiency calculation results of the petrochemical complexes based upon the sulfur oil shales processing by solid (ash) heat-carrier low-temperature carbonization plants by Galoter technology. The criterion for such enterprises fuel efficiency determining was developed on the base of the exergy methodology taking into account the recurrent publications consolidation. In this case, in supplying the consumers with paving bitumen, motor benzol, thiophene, toluene, 2-methylthiophene, xylene, gas sulfur, complex thermodynamic effectiveness was founded to amount to 53 %, and if ash residue realization is possible then it was founded to be to 70 %. The project economic attractiveness determining studies depending on the feedstock cost, its delivery way and investments amount changing were conducted.

  1. New options for conversion of vegetable oils to alternative fuels

    Energy Technology Data Exchange (ETDEWEB)

    Demirbas, A.; Kara, H. [Selcuk University, Konya (Turkey). Department of Chemical Engineering

    2006-05-15

    Biodiesel from transesterification of vegetable oils is an excellent alternative fuel. There is, however, a need to develop a direct process for conversion of vegetable oils into gasoline-competitive biodiesel and other petroleum products. Methyl esters of vegetable oils have several outstanding advantages among other new-renewable and clean engine fuel alternatives. The purpose of the transesterification process is to lower the viscosity of vegetable oil. Compared to No. 2 diesel fuel, all of the vegetable oils are much more viscous, whereas methyl esters of vegetable oils are slightly more viscous. The methyl esters are more volatile than those of the vegetable oils. Conversion of vegetable oils to useful fuels involves the pyrolysis and catalytic cracking of the oils into lower molecular products. Pyrolysis produces more biogasoline than biodiesel fuel. Soap pyrolysis products of vegetable oils can be used as alternative diesel engine fuel. The soaps obtained from the vegetable oils can be pyrolyzed into hydrocarbon-rich products. Zinc chloride catalyst contributed greatly to high amounts of hydrocarbons in the liquid product. The yield of ZnCl2 catalytic conversion of the soybean oil reached the maximum 79.9% at 660 K. (author)

  2. Comparative Evaluation of Phase 1 Results from the Energy Conversion Alternatives Study (ECAS). [coal utilization for electric power plants feasibility analysis

    Science.gov (United States)

    1976-01-01

    Ten advanced energy conversion systems for central-station, based-load electric power generation using coal and coal-derived fuels which were studied by NASA are presented. Various contractors were selected by competitive bidding to study these systems. A comparative evaluation is provided of the contractor results on both a system-by-system and an overall basis. Ground rules specified by NASA, such as coal specifications, fuel costs, labor costs, method of cost comparison, escalation and interest during construction, fixed charges, emission standards, and environmental conditions, are presented. Each system discussion includes the potential advantages of the system, the scope of each contractor's analysis, typical schematics of systems, comparison of cost of electricity and efficiency for each contractor, identification and reconciliation of differences, identification of future improvements, and discussion of outside comments. Considerations common to all systems, such as materials and furnaces, are also discussed. Results of selected in-house analyses are presented, in addition to contractor data. The results for all systems are then compared.

  3. Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 2: Materials considerations. [materials used in boilers and heat exchangers of energy conversion systems for electric power plants using coal

    Science.gov (United States)

    Thomas, D. E.

    1976-01-01

    Extensive studies are presented which were carried out on materials behavior in nine advanced energy conversion systems employing coal and coal-derived fuels. The areas of materials behavior receiving particular attention in this regard are: (1) fireside corrosion and erosion in boiler and heat exchanger materials, (2) oxidation and hot corrosion of gas turbine materials, (3) liquid metal corrosion and mass transport, (4) high temperature steam corrosion, (5) compatability of materials with coal slag and MHD seed, (6) reaction of materials with impure helium, (7) allowable stresses for boiler and heat exchanger materials, (8) environmental effects on mechanical properties, and (9) liquid metal purity control and instrumentation. Such information was then utilized in recommending materials for use in the critical components of the power systems, and at the same time to identify materials problem areas and to evaluate qualitatively the difficulty of solving those problems. Specific materials recommendations for critical components of the nine advanced systems under study are contained in summary tables.

  4. Seal design alternatives study

    International Nuclear Information System (INIS)

    Van Sambeek, L.L.; Luo, D.D.; Lin, M.S.; Ostrowski, W.; Oyenuga, D.

    1993-06-01

    This report presents the results from a study of various sealing alternatives for the WIPP sealing system. Overall, the sealing system has the purpose of reducing to the extent possible the potential for fluids (either gas or liquid) from entering or leaving the repository. The sealing system is divided into three subsystems: drift and panel seals within the repository horizon, shaft seals in each of the four shafts, and borehole seals. Alternatives to the baseline configuration for the WIPP seal system design included evaluating different geometries and schedules for seal component installations and the use of different materials for seal components. Order-of-magnitude costs for the various alternatives were prepared as part of the study. Firm recommendations are not presented, but the advantages and disadvantages of the alternatives are discussed. Technical information deficiencies are identified and studies are outlined which can provide required information

  5. Development of bioenergy conversion alternatives for climate change mitigation

    Energy Technology Data Exchange (ETDEWEB)

    Derkyi, Nana S.A.; Sekyere, Daniel [CSIR-FORIG, Kwame Nkrumah University of Science and Technology KNUST Box 63 (Ghana); Okyere, Philip Y. [Electrical Engineering Department, Kwame Nkrumah University of Science and Technology KNUST (Ghana); Darkwa, Nicholas A. [FRNR, Kwame Nkrumah University of Science and Technology KNUST (Ghana); Nketiah, Samuel K. [TROPENBOS International (Ghana)

    2011-07-01

    Traditional charcoal production, firewood sourcing and over-dependence on the national grid for electricity are associated with high greenhouse gas emissions relative to other common energy options. However, there have been few attempts to analyze the potential of cogeneration and briquetting as favourable energy options for climate change mitigation. The possibility of utilizing abundant wood residues to produce energy for domestic and industrial application through co-generation and sawdust briquetting was assessed. Annual residues generated in the three mills studied ranged from 19,230 m3 to 32,610 m3. Annual output of semi-carbonized and carbonized sawdust briquette from the briquette factory studied was 1400 tonnes. Heating values of the wood species ranged from 8.2 to 20.3 MJ/kg. Power requirements for the mills, necessary for sizing co-generation units were derived from their monthly electricity bills. Power ratings for co-generation units were specified between 400 kWe to 2000 kWe with heat to power ratios of 19 to 21. The energy generated could be used to produce electrical power and reduce dependency on the national grid. Conversion of sawdust in the briquette factory potentially contributes a saving of 5,600 tonnes of trees/year that would have been cut from the forest. Thus, adoption of co-generation and sawdust briquetting nationwide could be of immense benefit to the country in terms of climate change mitigation.

  6. 76 FR 19829 - Clean Alternative Fuel Vehicle and Engine Conversions

    Science.gov (United States)

    2011-04-08

    ... INFORMATION CONTACT: Amy Bunker, Compliance and Innovative Strategies Division, U.S. Environmental Protection... Vehicle/Engine Selection D. Mixed-Fuel and Dual-Fuel Conversions E. Vehicle/Engine Labels, Packaging Labels, and Marketing F. Compliance 1. Emission Standards a. Light-Duty and Heavy-Duty Chassis Certified...

  7. Alternate Strategies for Conversion of Waste Plastic to Fuels

    OpenAIRE

    Neha Patni; Pallav Shah; Shruti Agarwal; Piyush Singhal

    2013-01-01

    The present rate of economic growth is unsustainable without saving of fossil energy like crude oil, natural gas, or coal. There are many alternatives to fossil energy such as biomass, hydropower, and wind energy. Also, suitable waste management strategy is another important aspect. Development and modernization have brought about a huge increase in the production of all kinds of commodities, which indirectly generate waste. Plastics have been one of the materials because of their wide range ...

  8. What Fleets Need to Know About Alternative Fuel Vehicle Conversions, Retrofits, and Repowers

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, K.; Gonzales, J.

    2017-10-02

    Many fleet managers have opted to incorporate alternative fuels and advanced vehicles into their lineup. Original equipment manufacturers (OEMs) offer a variety of choices, and there are additional options offered by aftermarket companies. There are also a myriad of ways that existing vehicles can be modified to utilize alternative fuels and other advanced technologies. Vehicle conversions and retrofit packages, along with engine repower options, can offer an ideal way to lower vehicle operating costs. This can result in long term return on investment, in addition to helping fleet managers achieve emissions and environmental goals. This report summarizes the various factors to consider when pursuing a conversion, retrofit, or repower option.

  9. What Fleets Need to Know About Alternative Fuel Vehicle Conversions, Retrofits, and Repowers

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, Kay L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gonzales, John [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2017-10-17

    Many fleet managers have opted to incorporate alternative fuels and advanced vehicles into their lineup. Original equipment manufacturers (OEMs) offer a variety of choices, and there are additional options offered by aftermarket companies. There are also a myriad of ways that existing vehicles can be modified to utilize alternative fuels and other advanced technologies. Vehicle conversions and retrofit packages, along with engine repower options, can offer an ideal way to lower vehicle operating costs. This can result in long term return on investment, in addition to helping fleet managers achieve emissions and environmental goals. This report summarizes the various factors to consider when pursuing a conversion, retrofit, or repower option.

  10. Normetex Pump Alternatives Study

    International Nuclear Information System (INIS)

    Clark, Elliot A.

    2013-01-01

    A mainstay pump for tritium systems, the Normetex scroll pump, is currently unavailable because the Normetex company went out of business. This pump was an all-metal scroll pump that served tritium processing facilities very well. Current tritium system operators are evaluating replacement pumps for the Normetex pump and for general used in tritium service. An all-metal equivalent alternative to the Normetex pump has not yet been identified. 1. The ideal replacement tritium pump would be hermetically sealed and contain no polymer components or oils. Polymers and oils degrade over time when they contact ionizing radiation. 2. Halogenated polymers (containing fluorine, chlorine, or both) and oils are commonly found in pumps. These materials have many properties that surpass those of hydrocarbon-based polymers and oils, including thermal stability (higher operating temperature) and better chemical resistance. Unfortunately, they are less resistant to degradation from ionizing radiation than hydrocarbon-based materials (in general). 3. Polymers and oils can form gaseous, condensable (HF, TF), liquid, and solid species when exposed to ionizing radiation. For example, halogenated polymers form HF and HCl, which are extremely corrosive upon reaction with water. If a pump containing polymers or oils must be used in a tritium system, the system must be designed to be able to process the unwanted by-products. Design features to mitigate degradation products include filters and chemical or physical traps (eg. cold traps, oil traps). 4. Polymer components can work in tritium systems, but must be replaced regularly. Polymer components performance should be monitored or be regularly tested, and regular replacement of components should be viewed as an expected normal event. A radioactive waste stream must be established to dispose of used polymer components and oil with an approved disposal plan developed based on the facility location and its regulators. Polymers have varying

  11. Status of RA3 conversion studies

    International Nuclear Information System (INIS)

    Testoni, J.

    1983-01-01

    Studies carried out at CNEA in Argentina for the conversion of the RA3 3.5 MW reactor to LEU fuel dealt with neutronic, thermal hydraulic, safety analysis, as well as fuel manufacture. Some of the results for the neutronic studies are reported

  12. Study on carbon dioxide conversion by radiation

    International Nuclear Information System (INIS)

    Cho, Young Hyun; Park, Geun Il; Cho, Il Hoon; Choi, Sang Do; Hong, Kwang Hee; Lee, Chang Woo

    1999-09-01

    This study was carried out to investigate the synergistic effects on the CO 2 conversion by the application of semiconductor in the field of gamma-ray. Gamma-ray irradiation was performed to examine the effects of semiconductor application on CO 2 conversion in water and the formation of organic material from carbonate solution. From experimental results it is clear that the supplication of semiconductor in the field of gamma-ray increases the efficiency for CO 2 conversion to organic matter. Based on the obtained experimental results it is obvious that the synergistic effects of semiconductor materials in the gamma-ray field leads to increase of the CO 2 conversion yield to organic matter up to 50 percent compared to the gamma-ray irradiation. The way of achieving higher activity is due to the catalytic action of semiconductor by gamma-ray irradiation. Zr-doped TiO 2 catalyst prepared by sol-gel method exhibits the higher efficiency for CO 2 conversion in aqueous solution and carbonate containing solution. This effect of Zr-doping can be explained by the formation of additional defects in surface of TiO 2 film. (author)

  13. Effects of a Conversation-Based Intervention on the Linguistic Skills of Children With Motor Speech Disorders Who Use Augmentative and Alternative Communication.

    Science.gov (United States)

    Soto, Gloria; Clarke, Michael T

    2017-07-12

    This study was conducted to evaluate the effects of a conversation-based intervention on the expressive vocabulary and grammatical skills of children with severe motor speech disorders and expressive language delay who use augmentative and alternative communication. Eight children aged from 8 to 13 years participated in the study. After a baseline period, a conversation-based intervention was provided for each participant, in which they were supported to learn and use linguistic structures essential for the formation of clauses and the grammaticalization of their utterances, such as pronouns, verbs, and bound morphemes, in the context of personally meaningful and scaffolded conversations with trained clinicians. The conversations were videotaped, transcribed, and analyzed using the Systematic Analysis of Language Transcripts (SALT; Miller & Chapman, 1991). Results indicate that participants showed improvements in their use of spontaneous clauses, and a greater use of pronouns, verbs, and bound morphemes. These improvements were sustained and generalized to conversations with familiar partners. The results demonstrate the positive effects of the conversation-based intervention for improving the expressive vocabulary and grammatical skills of children with severe motor speech disorders and expressive language delay who use augmentative and alternative communication. Clinical and theoretical implications of conversation-based interventions are discussed and future research needs are identified. https://doi.org/10.23641/asha.5150113.

  14. Effects of a Conversation-Based Intervention on the Linguistic Skills of Children with Motor Speech Disorders Who Use Augmentative and Alternative Communication

    Science.gov (United States)

    Soto, Gloria; Clarke, Michael T.

    2017-01-01

    Purpose: This study was conducted to evaluate the effects of a conversation-based intervention on the expressive vocabulary and grammatical skills of children with severe motor speech disorders and expressive language delay who use augmentative and alternative communication. Method: Eight children aged from 8 to 13 years participated in the study.…

  15. [Fresh fruit and occultism as ways to salvation: conversions in Leipzig's alternative culture at around 1900].

    Science.gov (United States)

    Bigalke, Bernadett

    2008-01-01

    During the time of the Wilhelmine Empire, there were multiple interdependencies between adherents of the life reform movement (vegetarians, naturopathists, nudists, etc.) and new religious movements such as esoteric groups like the theosophists in the alternative cultural milieu around 1900. These networks became visible in the form of double memberships in associations. However, there were also ambiguous affiliations, migration between groups and syncretistic beliefs without institutional belonging. The similarity between patterns of argumentation for this specific lifestyle and the congruence of chosen goals, ways and goods of salvation become particularly clear in this context. These forms of "methodical lifestyle" may lead to the development of a specific ethos or habitus (Max Weber). To illustrate these processes, this article analyses the report of a Leipzig lady who ate raw fruits and vegetables only, and examines her broader social context. Thereby the analysis will employ sociological theories of conversion to explain the case of Hedwig Bresch.

  16. A guide to the emissions certification procedures for alternative fuel aftermarket conversions

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-01-01

    Emissions certification is still relatively new to the aftermarket vehicle conversion industry. Many in the industry think that as soon as a vehicle is converted to operate on compressed natural gas (CNG) or liquefied petroleum gas (LFG), it automatically runs as clean as or cleaner than it did on the conventional fuel. However, recent studies have shown that aftermarket conversions may not always reduce emissions. To achieve emissions benefits, the conversion equipment must be designed and calibrated specifically for the engine and emissions control system on which it has been installed, and the installation and setup must be performed so as to not adversely affect the vehicle`s original emissions performance. The reason for certification, then, is to ensure that these criteria are met, that the vehicle continues to perform properly, and that it continues to satisfy all appropriate emissions standards throughout its useful life. The authors have prepared this guide to help equipment manufacturers, distributors, and installers understand the emissions certification process for aftermarket conversions. The guide gives an overview of the certification requirements established by the US EPA and by the state of California.

  17. Inertial confinement fusion reaction chamber and power conversion system study

    International Nuclear Information System (INIS)

    Maya, I.; Schultz, K.R.; Battaglia, J.M.

    1984-09-01

    GA Technologies has developed a conceptual ICF reactor system based on the Cascade rotating-bed reaction chamber concept. Unique features of the system design include the use of low activation SiC in a reaction chamber constructed of box-shaped tiles held together in compression by prestressing tendons to the vacuum chamber. Circulating Li 2 O granules serve as the tritium breeding and energy transport material, cascading down the sides of the reaction chamber to the power conversion system. The total tritium inventory of the system is 6 kg; tritium recovery is accomplished directly from the granules via the vacuum system. A system for centrifugal throw transport of the hot Li 2 O granules from the reaction chamber to the power conversion system has been developed. A number of issues were evaluated during the course of this study. These include the response of first-layer granules to the intense microexplosion surface heat flux, cost effective fabrication of Li 2 O granules, tritium inventory and recovery issues, the thermodynamics of solids-flow options, vacuum versus helium-medium heat transfer, and the tradeoffs of capital cost versus efficiency for alternate heat exchange and power conversion system option. The resultant design options appear to be economically competitive, safe, and environmentally attractive

  18. HEU to LEU conversion and blending facility: UNH blending alternative to produce LEU oxide for disposal

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than is the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This report provides data to be used in the environmental impact analysis for the uranyl nitrate hexahydrate blending option to produce oxide for disposal. This the Conversion and Blending Facility (CBF) alternative will have two missions (1) convert HEU materials into HEU uranyl nitrate (UNH) and (2) blend the HEU uranyl nitrate with depleted and natural assay uranyl nitrate to produce an oxide that can be stored until an acceptable disposal approach is available. The primary emphasis of this blending operation will be to destroy the weapons capability of large, surplus stockpiles of HEU. The blended LEU product can only be made weapons capable again by the uranium enrichment process. The blended LEU will be produced as a waste suitable for storage or disposal.

  19. HEU to LEU conversion and blending facility: UNH blending alternative to produce LEU oxide for disposal

    International Nuclear Information System (INIS)

    1995-09-01

    The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than is the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This report provides data to be used in the environmental impact analysis for the uranyl nitrate hexahydrate blending option to produce oxide for disposal. This the Conversion and Blending Facility (CBF) alternative will have two missions (1) convert HEU materials into HEU uranyl nitrate (UNH) and (2) blend the HEU uranyl nitrate with depleted and natural assay uranyl nitrate to produce an oxide that can be stored until an acceptable disposal approach is available. The primary emphasis of this blending operation will be to destroy the weapons capability of large, surplus stockpiles of HEU. The blended LEU product can only be made weapons capable again by the uranium enrichment process. The blended LEU will be produced as a waste suitable for storage or disposal

  20. Web Conversations About Complementary and Alternative Medicines and Cancer: Content and Sentiment Analysis

    Science.gov (United States)

    Truccolo, Ivana; Antonini, Marialuisa; Rinaldi, Fabio; Omero, Paolo; Ferrarin, Emanuela; De Paoli, Paolo; Tasso, Carlo

    2016-01-01

    Background The use of complementary and alternative medicine (CAM) among cancer patients is widespread and mostly self-administrated. Today, one of the most relevant topics is the nondisclosure of CAM use to doctors. This general lack of communication exposes patients to dangerous behaviors and to less reliable information channels, such as the Web. The Italian context scarcely differs from this trend. Today, we are able to mine and analyze systematically the unstructured information available in the Web, to get an insight of people’s opinions, beliefs, and rumors concerning health topics. Objective Our aim was to analyze Italian Web conversations about CAM, identifying the most relevant Web sources, therapies, and diseases and measure the related sentiment. Methods Data have been collected using the Web Intelligence tool ifMONITOR. The workflow consisted of 6 phases: (1) eligibility criteria definition for the ifMONITOR search profile; (2) creation of a CAM terminology database; (3) generic Web search and automatic filtering, the results have been manually revised to refine the search profile, and stored in the ifMONITOR database; (4) automatic classification using the CAM database terms; (5) selection of the final sample and manual sentiment analysis using a 1-5 score range; (6) manual indexing of the Web sources and CAM therapies type retrieved. Descriptive univariate statistics were computed for each item: absolute frequency, percentage, central tendency (mean sentiment score [MSS]), and variability (standard variation σ). Results Overall, 212 Web sources, 423 Web documents, and 868 opinions have been retrieved. The overall sentiment measured tends to a good score (3.6 of 5). Quite a high polarization in the opinions of the conversation partaking emerged from standard variation analysis (σ≥1). In total, 126 of 212 (59.4%) Web sources retrieved were nonhealth-related. Facebook (89; 21%) and Yahoo Answers (41; 9.7%) were the most relevant. In total, 94 CAM

  1. Web Conversations About Complementary and Alternative Medicines and Cancer: Content and Sentiment Analysis.

    Science.gov (United States)

    Mazzocut, Mauro; Truccolo, Ivana; Antonini, Marialuisa; Rinaldi, Fabio; Omero, Paolo; Ferrarin, Emanuela; De Paoli, Paolo; Tasso, Carlo

    2016-06-16

    The use of complementary and alternative medicine (CAM) among cancer patients is widespread and mostly self-administrated. Today, one of the most relevant topics is the nondisclosure of CAM use to doctors. This general lack of communication exposes patients to dangerous behaviors and to less reliable information channels, such as the Web. The Italian context scarcely differs from this trend. Today, we are able to mine and analyze systematically the unstructured information available in the Web, to get an insight of people's opinions, beliefs, and rumors concerning health topics. Our aim was to analyze Italian Web conversations about CAM, identifying the most relevant Web sources, therapies, and diseases and measure the related sentiment. Data have been collected using the Web Intelligence tool ifMONITOR. The workflow consisted of 6 phases: (1) eligibility criteria definition for the ifMONITOR search profile; (2) creation of a CAM terminology database; (3) generic Web search and automatic filtering, the results have been manually revised to refine the search profile, and stored in the ifMONITOR database; (4) automatic classification using the CAM database terms; (5) selection of the final sample and manual sentiment analysis using a 1-5 score range; (6) manual indexing of the Web sources and CAM therapies type retrieved. Descriptive univariate statistics were computed for each item: absolute frequency, percentage, central tendency (mean sentiment score [MSS]), and variability (standard variation σ). Overall, 212 Web sources, 423 Web documents, and 868 opinions have been retrieved. The overall sentiment measured tends to a good score (3.6 of 5). Quite a high polarization in the opinions of the conversation partaking emerged from standard variation analysis (σ≥1). In total, 126 of 212 (59.4%) Web sources retrieved were nonhealth-related. Facebook (89; 21%) and Yahoo Answers (41; 9.7%) were the most relevant. In total, 94 CAM therapies have been retrieved. Most

  2. Case Study: Camptocormia, a Rare Conversion Disorder.

    Science.gov (United States)

    Rajmohan, Velayudhan; Thomas, Biju; Sreekumar, Kumaran

    2004-01-01

    Camptocormia is a condition characterized by severe frontal flexion of the spinal cord and knees, with passive drooping of both arms. It occurs as a form of conversion disorder. Some cases are associated with behavioral problems. A case of camptocormia of 2-year duration in a south Indian adolescent girl with oppositional defiant disorder and…

  3. CFD Studies on Biomass Thermochemical Conversion

    Directory of Open Access Journals (Sweden)

    Lifeng Yan

    2008-06-01

    Full Text Available Thermochemical conversion of biomass offers an efficient and economically process to provide gaseous, liquid and solid fuels and prepare chemicals derived from biomass. Computational fluid dynamic (CFD modeling applications on biomass thermochemical processes help to optimize the design and operation of thermochemical reactors. Recent progression in numerical techniques and computing efficacy has advanced CFD as a widely used approach to provide efficient design solutions in industry. This paper introduces the fundamentals involved in developing a CFD solution. Mathematical equations governing the fluid flow, heat and mass transfer and chemical reactions in thermochemical systems are described and sub-models for individual processes are presented. It provides a review of various applications of CFD in the biomass thermochemical process field.

  4. Alternative Education Completers: A Phenomenological Study

    Science.gov (United States)

    Murray, Becky L.; Holt, Carleton R.

    2014-01-01

    The purpose of this study was to explore the elements of the alternative education experience significant to successful completion of the program. This phenomenological paradigm provided the framework for all aspects of the qualitative study. Students, parents, administrators, and staff members of two alternative programs in the southeast Kansas…

  5. Alternative Middle School Models: An Exploratory Study

    Science.gov (United States)

    Duffield, Stacy Kay

    2018-01-01

    A Midwestern state allocated grant funding to encourage more accessible alternative programming at the middle level. Seventeen schools were approved for this grant and used the funds to supplement the operation of a new or existing program. This study provides policymakers and educators with an overview of the various types of alternative middle…

  6. Study of electrochemical phosphate conversion coating of metallic surfaces

    International Nuclear Information System (INIS)

    Gougelin, Patrick

    1985-01-01

    After an overview on phosphate conversion coating processes, on models of iron electrochemical dissolution, on the passivation phenomenon, and on the phosphate conversion coating treatment, this research thesis reports a detailed study of this last process. The author presents the experimental method, reports the study of this process and of passivation under constant polarization. He reports the use of various techniques and conditions: chrono-amperometry, chrono-potentiometry, cyclic volt-amperometry

  7. Hopewell Furnace NHS : alternative transportation study

    Science.gov (United States)

    2009-12-31

    This study assesses the potential for an alternative transportation system (ATS) at Hopewell Furnace National Historic Site (NHS). The Volpe Center investigated internal circulation and potential partnerships with local historic, cultural, and recrea...

  8. CRADA Final Report for CRADA Number NFE-10-02991 "Development and Commercialization of Alternative Carbon Precursors and Conversion Technologies"

    Energy Technology Data Exchange (ETDEWEB)

    Norris, Rober [ORNL; Paulauskas, Felix [ORNL; Naskar, Amit [ORNL; Kaufman, Michael [ORNL; Yarborough, Ken [ORNL; Derstine, Chris [The Dow Chemical Company

    2013-10-01

    The overall objective of the collaborative research performed by the Oak Ridge National Laboratory (ORNL) and the Dow Chemical Company under this Cooperative Research And Development Agreement (CRADA NFE-10-02991) was to develop and establish pathways to commercialize new carbon fiber precursor and conversion technology. This technology is to produce alternative polymer fiber precursor formulations as well as scaled energy-efficient advanced conversion technology to enable continuous mode conversion to obtain carbonized fibers that are technically and economically viable in industrial markets such as transportation, wind energy, infrastructure and oil drilling applications. There have been efforts in the past to produce a low cost carbon fiber. These attempts have to be interpreted against the backdrop of the market needs at the time, which were strictly military aircraft and high-end aerospace components. In fact, manufacturing costs have been reduced from those days to current practice, where both process optimization and volume production have enabled carbon fiber to become available at prices below $20/lb. However, the requirements of the lucrative aerospace market limits further price reductions from current practice. This approach is different because specific industrial applications are targeted, most specifically wind turbine blade and light vehicle transportation, where aircraft grade carbon fiber is not required. As a result, researchers are free to adjust both manufacturing process and precursor chemistry to meet the relaxed physical specifications at a lower cost. This report documents the approach and findings of this cooperative research in alternative precursors and advanced conversion for production of cost-effective carbon fiber for energy missions. Due to export control, proprietary restrictions, and CRADA protected data considerations, specific design details and processing parameters are not included in this report.

  9. "Spiritual but not religious": Cognition, schizotypy, and conversion in alternative beliefs.

    Science.gov (United States)

    Willard, Aiyana K; Norenzayan, Ara

    2017-08-01

    The spiritual but not religious (SBNR) are a growing population in secularizing societies. Yet, we know little about the underlying psychology of this group or their belief profile. Based on an individual difference approach, we address this knowledge gap by comparing SBNR with religious and non-religious participants. In a sample of Americans (n=1013), we find that the SBNR differ from non-religious and religious participants in a number of ways. SBNR participants are more likely to hold paranormal beliefs and to have an experiential relationship to the supernatural (e.g. have mystical experiences and feelings of universal connectedness), but are similar to religious participants in their profile of cognitive biases. SBNR participants score higher on measures of schizotypy than the religious or non-religious. Reported conversions from one group (religious, SBNR, or non-religious) to another since childhood corresponds with predictable differences in cognitive biases, with dualism predicting conversion to religion and schizotypy predicting conversion to SBNR. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. HEU to LEU conversion and blending facility: Metal blending alternative to produce LEU oxide for disposal

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. The nuclear material is converted to a form more proliferation- resistant than the original form. Blending HEU (highly enriched uranium) with less-enriched uranium to form LEU has been proposed as a disposition option. Five technologies are being assessed for blending HEU. This document provides data to be used in environmental impact analysis for the HEU-LEU disposition option that uses metal blending with an oxide waste product. It is divided into: mission and assumptions, conversion and blending facility descriptions, process descriptions and requirements, resource needs, employment needs, waste and emissions from plant, hazards discussion, and intersite transportation.

  11. HEU to LEU conversion and blending facility: Metal blending alternative to produce LEU oxide for disposal

    International Nuclear Information System (INIS)

    1995-09-01

    US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. The nuclear material is converted to a form more proliferation- resistant than the original form. Blending HEU (highly enriched uranium) with less-enriched uranium to form LEU has been proposed as a disposition option. Five technologies are being assessed for blending HEU. This document provides data to be used in environmental impact analysis for the HEU-LEU disposition option that uses metal blending with an oxide waste product. It is divided into: mission and assumptions, conversion and blending facility descriptions, process descriptions and requirements, resource needs, employment needs, waste and emissions from plant, hazards discussion, and intersite transportation

  12. Enculturating Conversational Agents based on a Comparative Corpus Study

    DEFF Research Database (Denmark)

    Lipi, Afia Akhter; Yamaoka, Yuji; Rehm, Matthias

    2008-01-01

    When encountering people who have a different cultural background from our own, many of us feel uncomfortable because gestures and facial expressions may not be familiar to us. Thus, to enhance the believability of conversational agents, culture-specific nonverbal behaviors should be implemented ...... a more detailed analysis about posture shifts, and proposes a chat system with an embodied conversational agent (ECA) that can act as a language trainer....... into the agents. In our previous study, with the goal of building a user interface that incorporates a user’s cultural background, we have collected comparative conversation corpus in Germany and Japan, and investigated the differences in gestures and posture shifts between these two countries. This paper reports...

  13. Studies on Chromium-free Conversion coatings on Aluminum | Oki ...

    African Journals Online (AJOL)

    The development of a chromium-free conversion coating on aluminum has been studied using transmission electron microscopy (TEM), Auger Electron (AES) and Secondary ion mass spectroscopy (SIMS) techniques. Within the limits of the resolution of the TEM, the coating is uniformly clear and featureless. It is composed ...

  14. Alternate fuel cycle technologies, nitrate-to-oxide conversion project. Progress report, January--June 1977

    International Nuclear Information System (INIS)

    Lehmkuhl, G.D.

    1977-01-01

    Work is being done at the Rocky Flats Plant (RFP) under contract from the Savannah River Operations Office (SROO) of the U.S. Energy Research and Development Administration (ERDA) to critically analyze and evaluate existing technology for converting plutonium nitrate to plutonium oxide, and to recommend flow sheets and equipment for this process. Seven such processes were compared using an expanded process-comparison scheme. The results of the comparison differed somewhat from the initial comparison made in September, 1976. The direct calcination methods, headed by the screw calciner process, received the highest ratings when operating experience was considered with a small weighting factor. These methods are much simpler than the others. The oxalate precipitation methods, headed by the plutonium(IV) oxalate precipitation and calcination process, received highest ratings when operating experience was strongly considered. Thus, in the long term, the screw calciner or other direct-conversion methods should be developed. For a plant to be built in the short term, however, an oxalate precipitation method should be used since a larger amount of experience exists with these processes. The block flow diagrams, material balances, and equipment flow sheets for each of the seven processes compared are included in this report. A process-design criterion is being prepared for a mechanical (screw calciner) direct-denitration process, and includes process flow sheets, a material balance, a process description, equipment performance specifications, the control philosophy and specifications, the operating philosophy, and a general process layout

  15. Feasibility study on conversion and storage of solar energy

    Energy Technology Data Exchange (ETDEWEB)

    Senghaphan, W; Tunsiri, P; Trivijitkasem, P; Ratanathammaphan, K

    1982-01-01

    A study has been conducted on the energy conversion system from solar energy to mechanical energy and on the efficiency of energy storage by an ordinary battery. The conversion system makes use of a thermal cycle, that is to say, the solar energy is collected as heat, and this heat makes suitable working substances evaporate into vapor with volume and pressure which can be used to drive the turbine resulting in mechanical energy. The vapor which passes through the turbine will have reduced pressure and reduced temperature and will be recondensed into liquid after passing through a suitable radiator. This liquid can be pumped back into the hot part of the conversion system with little energy. It is found by this study that the turbine could be operated by using acetone as working substance with a 80-90/sup 0/C source of heat. In the energy conversion system from solar energy to electrical energy, it is essential to provide for an energy storage, so that energy can be used in the absence of sunshine. To store energy by using a batter is one of the convenient methods. Therefore the efficiency of the batteries has been studied. Owing to incompleteness of the researched system, a conventional DC power supply has been used for charging the batteries. It is found that the efficiency of the charging and discharging cycle of batteries is about 40-60%.

  16. Blocking hexose entry into glycolysis activates alternative metabolic conversion of these sugars and upregulates pentose metabolism in Aspergillus nidulans

    Energy Technology Data Exchange (ETDEWEB)

    Khosravi, Claire; Battaglia, Evy; Kun, Roland S.; Dalhuijsen, Sacha; Visser, Jaap; Aguilar-Pontes, Maria V.; Zhou, Miamiao; Heyman, Heino M.; Kim, Young-Mo; Baker, Scott E.; de Vries, Ronald P.

    2018-03-22

    Background: Plant biomass is the most abundant carbon source for many fungal species. In the biobased industry fungi are used to produce lignocellulolytic enzymes to degrade agricultural waste biomass. Here we evaluated if it would be possible to create an Aspergillus nidulans strain that releases but does not metabolize hexoses from plant biomass. For this purpose, metabolic mutants were generated that were impaired in glycolysis, by using hexokinase (hxkA) and glucokinase (glkA) negative strains. To prevent repression of enzyme production due to the hexose accumulation, strains were generated that combined these mutations with a deletion in creA, the repressor involved in regulating preferential use of different carbon catabolic pathways. Results: Phenotypic analysis revealed reduced growth for the hxkA1 glkA4 mutant on wheat bran. However, hexoses did not accumulate during growth of the mutants on wheat bran, suggesting that glucose metabolism is re-routed towards alternative carbon catabolic pathways. The creAΔ4 mutation in combination with preventing initial phosphorylation in glycolysis resulted in better growth than the hxkA/glkA mutant and an increased expression of pentose catabolic and pentose phosphate pathway genes. This indicates that the reduced ability to use hexoses as carbon sources created a shift towards the pentose fraction of wheat bran as a major carbon source to support growth. Conclusion: Blocking the direct entry of hexoses to glycolysis activates alternative metabolic conversion of these sugars in A. nidulans during growth on plant biomass, but also upregulates conversion of other sugars, such as pentoses.

  17. Preconceptual design studies and cost data of depleted uranium hexafluoride conversion plants

    International Nuclear Information System (INIS)

    Jones, E

    1999-01-01

    One of the more important legacies left with the Department of Energy (DOE) after the privatization of the United States Enrichment Corporation is the large inventory of depleted uranium hexafluoride (DUF6). The DOE Office of Nuclear Energy, Science and Technology (NE) is responsible for the long-term management of some 700,000 metric tons of DUF6 stored at the sites of the two gaseous diffusion plants located at Paducah, Kentucky and Portsmouth, Ohio, and at the East Tennessee Technology Park in Oak Ridge, Tennessee. The DUF6 management program resides in NE's Office of Depleted Uranium Hexafluoride Management. The current DUF6 program has largely focused on the ongoing maintenance of the cylinders containing DUF6. However, the long-term management and eventual disposition of DUF6 is the subject of a Programmatic Environmental Impact Statement (PEIS) and Public Law 105-204. The first step for future use or disposition is to convert the material, which requires construction and long-term operation of one or more conversion plants. To help inform the DUF6 program's planning activities, it was necessary to perform design and cost studies of likely DUF6 conversion plants at the preconceptual level, beyond the PEIS considerations but not as detailed as required for conceptual designs of actual plants. This report contains the final results from such a preconceptual design study project. In this fast track, three month effort, Lawrence Livermore National Laboratory and Bechtel National Incorporated developed and evaluated seven different preconceptual design cases for a single plant. The preconceptual design, schedules, costs, and issues associated with specific DUF6 conversion approaches, operating periods, and ownership options were evaluated based on criteria established by DOE. The single-plant conversion options studied were similar to the dry-conversion process alternatives from the PEIS. For each of the seven cases considered, this report contains information on

  18. Assateague Island National Seashore alternative transportation systems planning study and business plan for alternative transportation

    Science.gov (United States)

    2012-08-31

    The purpose of this study was to (1) study the potential expansion of existing alternative transportation systems (bicycle facilities) and development of new alternative transportation systems in and around the Maryland District of Assateague Island ...

  19. IRT - Sofia conversion feasibility study experience 2002-2009

    Energy Technology Data Exchange (ETDEWEB)

    Belousov, S.I.; Apostolov, T.G. [Institute for Nuclear Research and Nuclear Energy of Bulgarian Academy of Science, Tsarigradsko 72, 1784 Sofia (Bulgaria)

    2010-07-01

    A joint conversion feasibility study concerning the IRT - Sofia research reactor between INRNE and the RERTR Program at ANL was initiated in 2002. The initial steps studies (up to 2006) were mainly focused on neutronics properties significant for reactor application and safety analyses. Thermal hydraulic, accident analyses as well as additional neutronics study required were performed after that (up to 2010). The obtained results show that the IRT-4M LEU fuel assemblies (19.75% {sup 235}U enrichment) are appropriate for IRT-Sofia conversion (IRT-Sofia was initially designed for the IRT-2M HEU fuel assemblies with 36% {sup 235}U enrichment). The results obtained in the frames of the joint study show that the IRT-Sofia operation even with usage of only one pump in the primary circuit meets all safety requirements at power level up to 1000 kW and that safety is maintained for accident transients. Presented results of analyses (neutronics, thermal hydraulic, and accident) and accumulated experience for the IRT-Sofia will be useful for other research reactors where conversion from IRT-2M (HEU) to IRT-4M (LEU) fuel is underway and/or foreseen. (authors)

  20. Field study plan for alternate barriers

    International Nuclear Information System (INIS)

    Freeman, H.D.; Gee, G.W.; Relyea, J.F.

    1989-05-01

    Pacific Northwest Laboratory (PNL) is providing technical assistance in selecting, designing, evaluating, and demonstrating protective barriers. As part of this technical assistance effort, asphalt, clay, and chemical grout will be evaluated for use as alternate barriers. The purpose of the subsurface layer is to reduce the likelihood that extreme events (i.e., 100-year maximum storms, etc.) will cause significant drainage through the barrier. The tests on alternate barriers will include laboratory and field analysis of the subsurface layer performance. This field test plan outlines the activities required to test and design subsurface moisture barriers. The test plan covers activities completed in FY 1988 and planned through FY 1992 and includes a field-scale test of one or more of the alternate barriers to demonstrate full-scale application techniques and to provide performance data on a larger scale. Tests on asphalt, clay, and chemical grout were initiated in FY 1988 in small (30.5 cm diameter) tube-layer lysimeters. The parameters used for testing the materials were different for each one. The tests had to take into account the differences in material characteristics and response to change in conditions, as well as information provided by previous studies. 33 refs., 8 figs., 1 tab

  1. NRC inspection alternatives. A study report

    International Nuclear Information System (INIS)

    Conver, S.K.; Legasey, E.E.; LeDoux, J.C.; Rehfuss, C.

    1977-04-01

    IE's efforts in pursuing various resident inspection concepts are consistent with the stated interests of the new Administration in improving federal oversight of the nuclear industry. Four alternative resident inspection concepts are described and evaluated vis-a-vis the current program. The concept of full-time onsite inspectors as a preferred alternative is discussed. The tasks necessary to implement this preferred alternative are described

  2. Critical Media and Communication Studies Today. A Conversation

    Directory of Open Access Journals (Sweden)

    Christian Fuchs

    2011-06-01

    Full Text Available This article documents a conversation between us that was first published in parallel on our two blogs http://dwmw.wordpress.com and http://fuchs.uti.at/blog. The conversation deals with our assessments of the status of Critical Media and Communication Studies today. We discuss the work of Dallas Smythe, how to study and assess Google, research dimensions of Critical Political Economy of the Media, how important each of these dimensions should be, the role of ideology critique for Critical Political Economy of the Media, the commonalities and differences between Political Economies of the Media and Critical Political Economy of the Media/Critique of the Political Economy of the Media, the role of Karl Marx for Political Economies of the Media, Nicholas Garnham's recent comments on the field of Critical Political Economy of the Media, neoliberalism and capitalist crisis as contexts for Political Economies of the Media. Comments are very welcome on our blogs, URLs to the specific blog postings can be found in the article sections.

  3. Autoignition Studies of Diesel Alternative Biofuels

    Science.gov (United States)

    Wang, Weijing

    The autoignition of biofuel compounds that offer potential as diesel fuel alternatives was studied under high-pressure engine-like conditions using the shock tube technique. Ignition delay times were determined in reflected shock experiments using measured pressure and electronically-excited OH emission. Measurements were made at conditions ranging from 650 to 1350 K, pressures from 6 to 50 atm, and for fuel/air/diluent mixtures at equivalence ratios from 0.5 to 2. The wide range of temperatures examined provides observation of autoignition in three reactivity regimes, including the negative temperature coefficient (NTC) regime which is characteristic of fuels containing alkyl functionalities. Compounds studied include biodiesel-related compounds and real biodiesel fuels, dimethyl ether, and 3-methylheptane which is representative of compounds found in synthetic diesel fuels produced using the Fischer-Tropsch and hydrotreatment processes. Biodiesel compounds studied include biodiesel surrogates, methyl decanoate, methyl-5-decenoate, and methyl-9-decenoate; compounds found in large quantities in biodiesels, methyl palmitate, methyl stearate, methyl oleate, and methyl linoleate; and soy-based and animal fat based methyl ester biodiesels. Comparison of biodiesel compounds illustrates the influence of molecular structure (e.g., chain length, double bonds, and ester functionality) on reactivity. For methyl decanoate, the effect of high pressure exhaust gas recirculation (EGR) conditions relevant to internal combustion engines was also determined. Results showed that the first-order influence of EGR by displacing fuel and O2 to decrease radical branching. Measurements were compared to kinetic modeling results from models available in the literature providing varying degrees of model validation. Reaction flux analyses were also carried out to further examine the kinetic differences in different temperature regimes for fuel compounds. For example, reaction flux analyses

  4. The Role of Hand-Assisted Laparoscopic Technique in the Age of Single-Incision Laparoscopy: An Effective Alternative to Avoid Open Conversion in Colorectal Surgery.

    Science.gov (United States)

    Jung, Kyung Uk; Yun, Seong Hyeon; Cho, Yong Beom; Kim, Hee Cheol; Lee, Woo Yong; Chun, Ho-Kyung

    2018-04-01

    Continuous efforts to reduce the numbers and size of incisions led to the emergence of a new technique, single-incision laparoscopic surgery (SILS). It has been rapidly accepted as the preferred surgical approach in the colorectal area. In the age of SILS, what is the role of hand-assisted laparoscopic surgery (HALS)? We introduce the way to take advantage of it, as an effective alternative to avoid open conversion. This is a retrospective review of prospectively collected data of SILS colectomies performed by a single surgeon in Samsung Medical Center between August 2009 and December 2012. Out of 631 cases of SILS colectomy, 47 cases needed some changes from the initial approach. Among these, five cases were converted to HALS. Four of them were completed successfully without the need for open conversion. One patient with rectosigmoid colon cancer invading bladder was finally opened to avoid vesical trigone injury. The mean operation time of the 4 patients was 265.0 minutes. The mean estimated blood loss was 587.5 mL. The postoperative complication rate associated with the operation was 25%. Conversion from SILS to HALS in colorectal surgery was feasible and effective. It seemed to add minimal morbidity while preserving advantages of minimally invasive surgery. It could be considered an alternative to open conversion in cases of SILS, especially when the conversion to conventional laparoscopy does not seem to be helpful.

  5. Ironmaking Process Alternative Screening Study, Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Lockwood Greene, . .

    2005-01-06

    Iron in the United States is largely produced from iron ore mined in the United States or imported from Canada or South America. The iron ore is typically smelted in Blast Furnaces that use primarily iron ore, iron concentrate pellets metallurgical coke, limestone and lime as the raw materials. Under current operating scenarios, the iron produced from these Blast Furnaces is relatively inexpensive as compared to current alternative iron sources, e.g. direct iron reduction, imported pig iron, etc. The primary problem the Blast Furnace Ironmaking approach is that many of these Blast furnaces are relatively small, as compared to the newer, larger Blast Furnaces; thus are relatively costly and inefficient to operate. An additional problem is also that supplies of high-grade metallurgical grade coke are becoming increasingly in short supply and costs are also increasing. In part this is due to the short supply and costs of high-grade metallurgical coals, but also this is due to the increasing necessity for environmental controls for coke production. After year 2003 new regulations for coke product environmental requirement will likely be promulgated. It is likely that this also will either increase the cost of high-quality coke production or will reduce the available domestic U.S. supply. Therefore, iron production in the United States utilizing the current, predominant Blast Furnace process will be more costly and would likely be curtailed due to a coke shortage. Therefore, there is a significant need to develop or extend the economic viability of Alternate Ironmaking Processes to at least partially replace current and declining blast furnace iron sources and to provide incentives for new capacity expansion. The primary conclusions of this comparative Study of Alternative Ironmaking Process scenarios are: (1) The processes with the best combined economics (CAPEX and OPEX impacts in the I.R.R. calculation) can be grouped into those Fine Ore based processes with no scrap

  6. Conceptual design study of high conversion light water reactor

    International Nuclear Information System (INIS)

    Okumura, Keisuke; Akie, Hiroshi; Mori, Takamasa; Nakagawa, Masayuki; Ishiguro, Yukio

    1990-06-01

    Since 1984, R and D work has been made for high conversion light water reactors (HCLWRs), at JAERI, to improve the natural uranium saving and effective plutonium utilization by the use of conventional or extended LWR technology. This report summarizes the results of the feasibility study made mainly from the viewpoint of nuclear design in the Phase-I Program (1985∼1989). Until now, the following various types of HCLWR core concepts have been investigated; 1) homogeneous core with tight pitch lattice of fuel rods, 2) homogeneous core with semi-tight pitch lattice, 3) spectral shift core using fertile rod with semi-tight pitch lattice, 4) flat-core, 5) axial heterogeneous core. The core burnup and thermohydraulic analyses during normal operations have been performed to clear up the burnup performances and feasibility for each core. Based on the analysis results, the axial heterogeneous HCLWR core was selected as the JAERI reference core. (author)

  7. Energy conservation in coal conversion. Final report, September 15, 1977--September 1, 1978. Selected case studies and conservation methodologies

    Energy Technology Data Exchange (ETDEWEB)

    Purcupile, J.C.

    1978-09-01

    The purpose of this study is to apply the methodologies developed in the Energy Conservation in Coal Conversion August, 1977 Progress Report - Contract No. EY77S024196 - to an energy efficient, near-term coal conversion process design, and to develop additional, general techniques for studying energy conservation and utilization in coal conversion processes. The process selected for study was the Ralph M. Parsons Company of Pasadena, California ''Oil/Gas Complex, Conceptual Design/Economic Analysis'' as described in R and D Report No. 114 - Interim Report No. 4, published March, 1977, ERDA Contract No. E(49-18)-1975. Thirteen papers representing possible alternative methods of energy conservation or waste heat utilization have been entered individually into EDB and ERA. (LTN)

  8. Parametric study for high conversion pebble bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Teuchert, E.; Ruetten, H. J.

    1975-06-15

    Tables are presented of fuel cycle costs, conversion ratios and accompanying variations in fuel element designs for a 3,00 MWth high conversion pebble bed reactor with initial high enriched uranium/thorium cycle and subsequent recycling of U-233, Pu-239 and Pu-241.

  9. Enhanced Access Design Alternative I Study

    International Nuclear Information System (INIS)

    Eble, G.B.

    1999-01-01

    The purpose of this document is to evaluate Enhanced Design Alternative (EDA) 1, the low temperature repository design concept (CRWMS M and O 1999a). This technical document will provide supporting information for Site Recommendation (SR) and License Application (LA). Preparation of this evaluation will be in accordance with the technical document preparation plan (TDPP), (CRWMS M and O 1999b). EDA 1, one of five EDAs, was evolved from evaluation of a series of design features and alternatives developed during the first phase of the License Application Design Selection (LADS) process. Low, medium, and high temperature concepts were developed from the design features and alternatives prepared during Phase 1 of the LADS effort (CRWMS M and O 1999a). EDA 1 will first be evaluated against a single Screening Criterion, outlined in CRWMS M and O 1999a, which addresses post-closure performance of the repository. The performance of the repository is defined quantitatively as the peak radiological dose rate to an average individual of a critical group at a distance of 20 km from the repository site within 10,000 years. To satisfy this criterion the peak dose rate must not exceed the anticipated regulatory level of 25 mrem/yr within 10,000 years. If the EDA meets the screening criterion, the EDA will be further evaluated against the LADS Phase 2 Evaluation Criteria contained in CRWMS M and O 1999a

  10. Foresight Study on Advanced Conversion Technologies of Fossil Fuels

    International Nuclear Information System (INIS)

    Claver, A.; Cabrera, J. A.

    2000-01-01

    The Observatorio de Prospectiva Tecnologica Industrial (OPTI) is a Foundation supported by the Ministry of Industry and Energy, (MINER) and has as main objective to provide a basic information and knowledge on technology evolution. This information will be accessible to the Administration and to the Companies and can be taking into account in planning and decision making of technology policies. Ciemat is member of OPTI and is the organism in charge of the actions in the Energy sector. CIEMAT has the responsibility on the realisation of the sector studies to get in three years (1998 to 2001) a foresight vision of the critical technology topics. The OPTI integrated strategic plan undertake the analysis of other seven technology sectors, with the same criteria on methodological aspects. Delphi method was used for the realization of the studies. It consisted of a survey conducted in two rounds using a questionnaire to check the experts opinion. The time frame of the studies was defined from 1999 to 2015. The study presented in this document has been performed by CIEMAT in the second stage of the OPTI activities. The main goal behind this study is to identify the advanced clean and efficient technologies for the conversion of fossil fuels to promote in our country. The questionnaire was addressed to 250 experts and the response rate was about the 37%, ratifying the final results. The spanish position and the barriers for the development of each technology has been determined and also the recommended measures to facilitate their performance in the future. This basic information is consider of main interest, taking in account the actual energetic situation with a foreseeable demand increase and fossil fuels dependence. (Author) 17 refs

  11. Categorical Alternatives: An Educational Criticism Study

    Directory of Open Access Journals (Sweden)

    Elizabeth J. EVANS

    2015-12-01

    Full Text Available In the writing of this paper, the design of which is based on Elliot Eisners Educational Criticism model, both linguistic and non-linguistic description were used to encourage the interpretation and evaluation of a specific and unique alternative educational setting. Five years ago, Ellens Learning Annex, a multi-age, one-room school house, was just next door to the researcher, while her son was struggling at the public school a mile away. A day spent observing Ellen and her students yielded data from which three general themes emerged: Heterogeneous age-grouping, place-based education, and sensory integration in a teaching and learning environment.

  12. A Descriptive Study of Decision-Making Conversations during Pediatric Intensive Care Unit Family Conferences.

    Science.gov (United States)

    Smith, Michael A; Clayman, Marla L; Frader, Joel; Arenson, Melanie; Haber-Barker, Natalie; Ryan, Claire; Emanuel, Linda; Michelson, Kelly

    2018-06-19

    Little is known about how decision-making conversations occur during pediatric intensive care unit (PICU) family conferences (FCs). Describe the decision-making process and implementation of shared decision making (SDM) during PICU FCs. Observational study. University-based tertiary care PICU, including 31 parents and 94 PICU healthcare professionals involved in FCs. We recorded, transcribed, and analyzed 14 PICU FCs involving decision-making discussions. We used a modified grounded theory and content analysis approach to explore the use of traditionally described stages of decision making (DM) (information exchange, deliberation, and determining a plan). We also identified the presence or absence of predefined SDM elements. DM involved the following modified stages: information exchange; information-oriented deliberation; plan-oriented deliberation; and determining a plan. Conversations progressed through stages in a nonlinear manner. For the main decision discussed, all conferences included a presentation of the clinical issues, treatment alternatives, and uncertainty. A minority of FCs included assessing the family's understanding (21%), assessing the family's need for input from others (28%), exploring the family's desired decision-making role (35%), and eliciting the family's opinion (42%). In the FCs studied, we found that DM is a nonlinear process. We also found that several SDM elements that could provide information about parents' perspectives and needs did not always occur, identifying areas for process improvement.

  13. Space electric power design study. [laser energy conversion

    Science.gov (United States)

    Martini, W. R.

    1976-01-01

    The conversion of laser energy to electrical energy is discussed. Heat engines in which the laser heats the gas inside the engine through a window as well as heat engines in which the gas is heated by a thermal energy storage reservoir which has been heated by laser radiation are both evaluated, as well as the necessary energy storage, transmission and conversion components needed for a full system. Preliminary system concepts are presented and a recommended development program is outlined. It appears possible that a free displacer Stirling engine operating directly a linear electric generator can convert 65% of the incident laser energy into electricity.

  14. High-performance alternating current field-induced chromatic-stable white polymer electroluminescent devices employing a down-conversion layer

    Energy Technology Data Exchange (ETDEWEB)

    Xia, Yingdong; Chen, Yonghua; Smith, Gregory M. [Center for Nanotechnology and Molecular Materials, Department of Physics, Wake Forest University, Winston-Salem, NC 27105 (United States); Sun, Hengda; Yang, Dezhi [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Nie, Wanyi; Li, Yuan; Huang, Wenxiao [Center for Nanotechnology and Molecular Materials, Department of Physics, Wake Forest University, Winston-Salem, NC 27105 (United States); Ma, Dongge [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Carroll, David L., E-mail: carroldl@wfu.edu [Center for Nanotechnology and Molecular Materials, Department of Physics, Wake Forest University, Winston-Salem, NC 27105 (United States)

    2015-05-15

    In this work, a high-performance alternating current (AC) filed-induced chromatic-stable white polymer electroluminescence (WFIPEL) device was fabricated by combining a fluorophor Poly(9,9-dioctylfluorene) (PFO)-based blue device with a yellow down-conversion layer (YAG:Ce). A maximum luminance of this down-conversion FIPEL device achieves 3230 cd m{sup −2}, which is 1.41 times higher than the device without the down-conversion layer. A maximum current efficiency and power efficiency of the down-conversion WFIPEL device reach 19.7 cd A{sup −1} at 3050 cd m{sup −2} and 5.37 lm W{sup −1} at 2310 cd m{sup −2} respectively. To the best of our knowledge, the power efficiency is one of the highest reports for the WFIPEL up to now. Moreover, Commison Internationale de L’Eclairage (CIE) coordinates of (0.28, 0.30) is obtained by adjusting the thickness of the down-conversion layer to 30 μm and it is kept stable over the entire AC-driven voltage range. We believe that this AC-driven, down-conversion, WFIPEL device may offer an easy way towards future flat and flexible lighting sources. - Highlights: • A high-performance AC filed-induced chromatic-stable white polymer electroluminescence (WFIPEL) device was fabricated. • A maximum luminance, current efficiency, and power efficiency achieves 3230 cd m{sup −2}, 19.7 cd A{sup −1}, and 5.37 lm W{sup −1}, respectively. • The power efficiency is one of the highest reports for the WFIPEL up to now. • The EL spectrum kept very stable over the entire AC-driven voltage range.

  15. A microfluidic chip for electrochemical conversions in drug metabolism studies

    NARCIS (Netherlands)

    Odijk, Mathieu; Baumann, A.; Lohmann, W.; van den Brink, Floris Teunis Gerardus; Olthuis, Wouter; Karst, U.; van den Berg, Albert

    2009-01-01

    We have designed a microfluidic microreactor chip for electrochemical conversion of analytes, containing a palladium reference electrode and platinum working and counter electrodes. The counter electrode is placed in a separate side-channel on chip to prevent unwanted side-products appearing in the

  16. Washoe Tribe Alternative Energy Feasibility Study Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Jennifer [Washoe Tribe of NV and CA

    2014-10-01

    The Washoe Tribe of Nevada and California was awarded funding to complete the Washoe Tribe Alternative Energy Feasibility Study project. The main goal of the project was to complete an alternative energy feasibility study. This study was completed to evaluate “the potential for development of a variety of renewable energy projects and to conduct an alternative energy feasibility study that determines which alternative energy resources have the greatest economic opportunity for the Tribe, while respecting cultural and environmental values” (Baker-Tilly, 2014). The study concluded that distributed generation solar projects are the best option for renewable energy development and asset ownership for the Washoe Tribe. Concentrating solar projects, utility scale wind projects, geothermal, and biomass resource projects were also evaluated during the study and it was determined that these alternatives would not be feasible at this time.

  17. Energy and cost saving results for advanced technology systems from the Cogeneration Technology Alternatives Study (CTAS)

    Science.gov (United States)

    Sagerman, G. D.; Barna, G. J.; Burns, R. K.

    1979-01-01

    An overview of the organization and methodology of the Cogeneration Technology Alternatives Study is presented. The objectives of the study were to identify the most attractive advanced energy conversion systems for industrial cogeneration applications in the future and to assess the advantages of advanced technology systems compared to those systems commercially available today. Advanced systems studied include steam turbines, open and closed cycle gas turbines, combined cycles, diesel engines, Stirling engines, phosphoric acid and molten carbonate fuel cells and thermionics. Steam turbines, open cycle gas turbines, combined cycles, and diesel engines were also analyzed in versions typical of today's commercially available technology to provide a base against which to measure the advanced systems. Cogeneration applications in the major energy consuming manufacturing industries were considered. Results of the study in terms of plant level energy savings, annual energy cost savings and economic attractiveness are presented for the various energy conversion systems considered.

  18. Integration through relatedness in the conversational model: a case study.

    Science.gov (United States)

    Haliburn, Joan

    2009-02-01

    The aim of this paper is to demonstrate the principles of the conversational model in two therapies with a patient, at 16 years of age and again 20 years later. Described is the first therapy of L, which commenced in hospital and continued twice weekly after discharge. L was an acutely disturbed 16-year-old female admitted for 4 months to the psychiatry ward, a dynamically oriented milieu of a University teaching hospital where I was training. This is followed by a brief description of L's second therapy. Supervision was through audiotape of sessions. At the conclusion of the first therapy, L was functioning well. Five years later, she married and had a child. She was referred to me again after she attempted suicide following an acute stressful event which resulted in hospitalization. She is more aware and reflective at present but continues to be vulnerable. Attention to certain aspects of the psychotherapeutic relationship is important as demonstrated in the conversational model.

  19. Study of a wind energy conversion system in New Hampshire

    Science.gov (United States)

    Lockwood, J.; Kraft, G.; Pregent, G.; Smukler, L.

    1981-08-01

    Concern over conventional energy costs and supplies is currently strong, particularly in New England region where eighty percent of the total energy is oil based; furthermore, forty percent of this region's total energy is OPEC oil. These figures contrast with national averages of forty-seven and thirteen percent, respectively (1). The quest to develop alternative and renewable energy sources indigenous to New England is understandable in light of these figures. The wind is one such source. The study of wind energy can be divided into three basic areas; these are technical, legal-institutional, and financial. The technical area encompasses collection and analysis of wind data, selection and installation of wind turbines and peripheral equipment, and operation and maintenance. The legal-institutional area encompasses the resolution of such issues as land use policies, power contracts, and state and federal regulations. The financial area encompasses the examination of investment opportunities made available by various site-machine combinations and the selling of such opportunities to the investment community.

  20. IronMaking Process Alternatives Screening Study

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2000-10-01

    This study by Lockwood Greene evaluates a number ironmaking processes. The appendices provide greater detail and further exploration of the ironmaking processes, including components, relative costs, and comparisons.

  1. Neural correlates of conversion disorder: overview and meta-analysis of neuroimaging studies on motor conversion disorder.

    Science.gov (United States)

    Boeckle, Markus; Liegl, Gregor; Jank, Robert; Pieh, Christoph

    2016-06-10

    Conversion Disorders (CD) are prevalent functional disorders. Although the pathogenesis is still not completely understood, an interaction of genetic, neurobiological, and psychosocial factors is quite likely. The aim of this study is to provide a systematic overview on imaging studies on CDs and investigate neuronal areas involved in Motor Conversion Disorders (MCD). A systematic literature search was conducted on CD. Subsequently a meta-analysis of functional neuroimaging studies on MCD was implemented using an Activation Likelihood Estimation (ALE). We calculated differences between patients and healthy controls as well as between affected versus unaffected sides in addition to an overall analysis in order to identify neuronal areas related to MCD. Patients with MCD differ from healthy controls in the amygdala, superior temporal lobe, retrosplenial area, primary motor cortex, insula, red nucleus, thalamus, anterior as well as dorsolateral prefrontal and frontal cortex. When comparing affected versus unaffected sides, temporal cortex, dorsal anterior cingulate cortex, supramarginal gyrus, dorsal temporal lobe, anterior insula, primary somatosensory cortex, superior frontal gyrus and anterior prefrontal as well as frontal cortex show significant differences. Neuronal areas seem to be involved in the pathogenesis, maintenance or as a result of MCD. Areas that are important for motor-planning, motor-selection or autonomic response seem to be especially relevant. Our results support the emotional unawareness theory but also underline the need of more support by conduction imaging studies on both CD and MCD.

  2. Study of the Effectiveness of OCR for Decentralized Data Capture and Conversion. Final Report.

    Science.gov (United States)

    Liston, David M.; And Others

    The ERIC network conversion to an OCR (Optical Character Recognition) mode of data entry was studied to analyze the potential effectiveness of OCR data entry for future EPC/s (Editorial Processing Centers). Study results are also applicable to any other system involving decentralized bibliographic data capture and conversion functions. The report…

  3. Alternative Frameworks for the Study of Man.

    Science.gov (United States)

    Markova, Ivana

    1979-01-01

    Two frameworks for the study of man are discussed. The Cartesian model views man as a physical object. A dialectic framework, with the emphasis on the self, grew out of nineteenth century romanticism and reflects the theories of Hegel. Both models have had an effect on social psychology and the study of interpersonal communication. (BH)

  4. Alternative Transportation Study : Monomoy National Wildlife Refuge.

    Science.gov (United States)

    2010-05-31

    This report provides an overview of the historic and current visitation, infrastructure, and transportation conditions related to Monomoy National Wildlife Refuge and the surrounding areas in Chatham, MA. The study defines transportation-related goal...

  5. Alternative transportation study : Wichita Mountains Wildlife Refuge

    Science.gov (United States)

    2010-08-01

    This report provides an assessment of historic and current visitation, infrastructure, and transportation conditions at the Wichita Mountains Wildlife Refuge and surrounding areas in southwest Oklahoma. The study defines transportation-related goals ...

  6. Study on the Conversion of Fuel Nitrogen Into NOx

    Directory of Open Access Journals (Sweden)

    Raminta Plečkaitienė

    2011-12-01

    Full Text Available The aim of this work is to investigate NOx regularities combusting fuels having high concentration of nitrogen and to develop methods that will reduce the conversion of fuel nitrogen into NOx. There are three solutions to reducing NOx concentration: the combustion of fuel mixing it with other types of “clean” fuel containing small amounts of nitrogen, laundering fuel and the combustion of fuel using carbon additives. These solutions can help with reducing the amount of nitrogen in the wood waste of furniture by about 30% by washing fuel with water. Therefore, NOx value may decrease by about 35%.Article in Lithuanian

  7. Cogeneration technology alternatives study. Volume 1: Summary report

    Science.gov (United States)

    1980-01-01

    Data and information in the area of advanced energy conversion systems for industrial congeneration applications in the 1985-2000 time period was studied. Six current and thirty-one advanced energy conversion systems were defined and combined with appropriate balance-of-plant equipment. Twenty-six industrial processes were selected from among the high energy consuming industries to serve as a framework for the study. Each conversion system was analyzed as a cogenerator with each industrial plant. Fuel consumption, costs, and environmental intrusion were evaluated and compared to corresponding traditional values. Various cogeneration strategies were analyzed and both topping and bottoming (using industrial by-product heat) applications were included. The advanced energy conversion technologies indicated reduced fuel consumption, costs, and emissions. Typically fuel energy savings of 10 to 25 percent were predicted compared to traditional on-site furnaces and utility electricity. With the variety of industrial requirements, each advanced technology had attractive applications. Overall, fuel cells indicated the greatest fuel energy savings and emission reductions. Gas turbines and combined cycles indicated high overall annual cost savings. Steam turbines and gas turbines produced high estimated returns. In some applications, diesels were most efficient. The advanced technologies used coal-derived fuels, or coal with advanced fluid bed combustion or on-site gasification systems.

  8. Mobile radio alternative systems study traffic model

    Science.gov (United States)

    Tucker, W. T.; Anderson, R. E.

    1983-06-01

    The markets for mobile radio services in non-urban areas of the United States are examined for the years 1985-2000. Three market categories are identified. New Services are defined as those for which there are different expressed ideas but which are not now met by any application of available technology. The complete fulfillment of the needs requires nationwide radio access to vehicles without knowledge of vehicle location, wideband data transmission from remote sites, one- and two way exchange of short data and control messages between vehicles and dispatch or control centers, and automatic vehicle location (surveillance). The commercial and public services market of interest to the study is drawn from existing users of mobile radio in non-urban areas who are dissatisfied with the geographical range or coverage of their systems. The mobile radio telephone market comprises potential users who require access to the public switched telephone network in areas that are not likely to be served by the traditional growth patterns of terrestrial mobile telephone services. Conservative, likely, and optimistic estimates of the markets are presented in terms of numbers of vehicles that will be served and the radio traffic they will generate.

  9. Sandy Hook : alternative access concept plan and vehicle replacement study

    Science.gov (United States)

    2009-06-01

    This study addresses two critical issues of concern to the Sandy Hook Unit of Gateway National : Recreational Area: (1) options for alternative access to Sandy Hook during peak summer season, : particularly when the park is closed to private vehicles...

  10. Surgical volume and conversion rate in laparoscopic hysterectomy: does volume matter? A multicenter retrospective cohort study.

    Science.gov (United States)

    Keurentjes, José H M; Briët, Justine M; de Bock, Geertruida H; Mourits, Marian J E

    2018-02-01

    A multicenter, retrospective, cohort study was conducted in the Netherlands. The aim was to evaluate whether surgical volume of laparoscopic hysterectomies (LHs) performed by proven skilled gynecologists had an impact on the conversion rate from laparoscopy to laparotomy. In 14 hospitals, all LHs performed by 19 proven skilled gynecologists between 2007 and 2010 were included in the analysis. Surgical volume, conversion rate and type of conversion (reactive or strategic) were retrospectively assessed. To estimate the impact of surgical volume on the conversion rate, logistic regressions were performed. These regressions were adjusted for patient's age, Body Mass Index (BMI), ASA classification, previous abdominal surgery and the indication (malignant versus benign) for the LH. During the study period, 19 proven skilled gynecologists performed a total of 1051 LHs. Forty percent of the gynecologists performed over 20 LHs per year (median 17.3, range 5.4-49.5). Conversion to laparotomy occurred in 5.0% of all LHs (53 of 1051); 38 (3.6%) were strategic and 15 (1.4%) were reactive conversions. Performing over 20 LHs per year was significantly associated with a lower overall conversion rate (OR adjusted 0.43, 95% CI 0.24-0.77), a lower strategic conversion rate (OR adjusted 0.32, 95% CI 0.16-0.65), but not with a lower reactive conversion rate (OR adjusted 0.96, 95% CI 0.33-2.79). A higher annual surgical volume of LHs by proven skilled gynecologists is inversely related to the conversion rate to laparotomy, and results in a lower strategic conversion rate.

  11. Energy and cost savings results for advanced technology systems from the Cogeneration Technology Alternatives Study /CTAS/

    Science.gov (United States)

    Sagerman, G. D.; Barna, G. J.; Burns, R. K.

    1979-01-01

    The Cogeneration Technology Alternatives Study (CTAS), a program undertaken to identify the most attractive advanced energy conversion systems for industrial cogeneration applications in the 1985-2000 time period, is described, and preliminary results are presented. Two cogeneration options are included in the analysis: a topping application, in which fuel is input to the energy conversion system which generates electricity and waste heat from the conversion system is used to provide heat to the process, and a bottoming application, in which fuel is burned to provide high temperature process heat and waste heat from the process is used as thermal input to the energy conversion system which generates energy. Steam turbines, open and closed cycle gas turbines, combined cycles, diesel engines, Stirling engines, phosphoric acid and molten carbonate fuel cells and thermionics are examined. Expected plant level energy savings, annual energy cost savings, and other results of the economic analysis are given, and the sensitivity of these results to the assumptions concerning fuel prices, price of purchased electricity and the potential effects of regional energy use characteristics is discussed.

  12. Study on HANARO core conversion using U-Mo fuel

    International Nuclear Information System (INIS)

    Lee, K.H.; Lee, C.S.; Seo, C.G.; Park, S.J.; Kim, H.; Kim, C.K.

    2002-01-01

    Two types of fuel rods with different fuel meat diameter and uranium density are considered for HANARO core conversion with high density U-Mo fuel. Arranging standard fuels of 5.0 g U/cc and 6.35 mm in diameter at the inner ring of an assembly and reduced fuels of 4.3 g U/cc and 5.49 mm in diameter at the outer ring of an assembly flattens the assembly power distribution and avoids the increase of linear heat generation rate due to using higher uranium density and less number of fuel rods. The maximum linear heat generation rate is similar with the current reference core and four fuel sites at the outer core in the reflector tank is converted to the irradiation sites to suit more demand on fuel tests and radioisotope production at outer core sites. This new core has 32% longer fuel cycle than the current reference core. (author)

  13. Power Conversion Study for High Temperature Gas-Cooled Reactors

    International Nuclear Information System (INIS)

    Chang Oh; Richard Moore; Robert Barner

    2005-01-01

    The Idaho National Laboratory (INL) is investigating a Brayton cycle efficiency improvement on a high temperature gas-cooled reactor (HTGR) as part of Generation-IV nuclear engineering research initiative. There are some technical issues to be resolved before the selection of the final design of the high temperature gas cooled reactor, called as a Next Generation Nuclear Plant (NGNP), which is supposed to be built at the INEEL by year 2017. The technical issues are the selection of the working fluid, direct vs. indirect cycle, power cycle type, the optimized design in terms of a number of intercoolers, and others. In this paper, we investigated a number of working fluids for the power conversion loop, direct versus indirect cycle, the effect of intercoolers, and other thermal hydraulics issues. However, in this paper, we present part of the results we have obtained. HYSYS computer code was used along with a computer model developed using Visual Basic computer language

  14. Accelerator-based conversion (ABC) of weapons plutonium: Plant layout study and related design issues

    International Nuclear Information System (INIS)

    Cowell, B.S.; Fontana, M.H.; Krakowski, R.A.; Beard, C.A.; Buksa, J.J.; Davidson, J.W.; Sailor, W.C.; Williamson, M.A.

    1995-01-01

    In preparation for and in support of a detailed R and D Plan for the Accelerator-Based Conversion (ABC) of weapons plutonium, an ABC Plant Layout Study was conducted at the level of a pre-conceptual engineering design. The plant layout is based on an adaptation of the Molten-Salt Breeder Reactor (MSBR) detailed conceptual design that was completed in the early 1070s. Although the ABC Plant Layout Study included the Accelerator Equipment as an essential element, the engineering assessment focused primarily on the Target; Primary System (blanket and all systems containing plutonium-bearing fuel salt); the Heat-Removal System (secondary-coolant-salt and supercritical-steam systems); Chemical Processing; Operation and Maintenance; Containment and Safety; and Instrumentation and Control systems. Although constrained primarily to a reflection of an accelerator-driven (subcritical) variant of MSBR system, unique features and added flexibilities of the ABC suggest improved or alternative approaches to each of the above-listed subsystems; these, along with the key technical issues in need of resolution through a detailed R ampersand D plan for ABC are described on the bases of the ''strawman'' or ''point-of-departure'' plant layout that resulted from this study

  15. Echolalia or functional repetition in conversation--a case study of an individual with Huntington's disease.

    Science.gov (United States)

    Saldert, Charlotta; Hartelius, Lena

    2011-01-01

    In this case study, we investigated the use of repetition in an individual with a neurogenic communication disorder. We present an analysis of interaction in natural conversations between a woman with advanced Huntington's disease (HD), whose speech had been described as sometimes characterised by echolalia, and her personal assistant. The conversational interaction is analysed on a sequential level, and recurrent patterns are explored. Although the ability of the person with HD to interact is affected by chorea, word retrieval problems and reduced comprehension, she takes an active part in conversation. The conversational partner's contributions are often adapted to her communicative ability as they are formulated as questions or suggestions that can be elaborated on or responded to with a simple 'yes' or 'no'. The person with HD often repeats the words of her conversational partner in a way that extends her contributions and shows listenership, and this use of repetition is also frequent in ordinary conversations between non-brain-damaged individuals. The results show that the conversation partners in this case cooperate in making the conversation proceed and evolve, and that verbal repetition is used in a way that works as a strategy for compensating for the impairment.

  16. Time to sputum conversion in multidrug-resistant tuberculosis patients in Armenia: retrospective cohort study

    Directory of Open Access Journals (Sweden)

    Arax Hovhannesyan

    2012-06-01

    Full Text Available OBJECTIVE: To characterize time to sputum conversion among patients with multidrug resistant tuberculosis who were enrolled into second-line tuberculosis treatment program; to identify risk factors for delayed sputum conversion. DESIGN: Retrospective cohort study designed to identify the factors associated with sputum conversion. Survival analysis was performed using Kaplan-Meier estimator to compute estimates for median time to sputum conversion and Cox proportional hazards model to compute hazard ratios (HR. RESULTS: Sputum conversion from positive to negative was observed in 134 out of 195 cases (69%. Among these who converted the median time to conversion was 3.7 months. Factors independently associated with time to sputum conversion in the proportional hazards model were: male sex (HR=0.51, 95% CI 0.32-0.81, ofloxacin-resistant tuberculosis (HR = 0.45, 95% CI 0.26-0.78 and first period of recruitment into second-line treatment (HR= 0.69, 95% CI 0.47-1.01. CONCLUSION: Time to sputum conversion in patients with multidrug-resistant tuberculosis in Armenia was 5.8 months (range 0.5-17.0 months. High level of ofloxacin resistance was the main reason for compromised response to treatment. Patients with a poor resistance profile and males should be targeted with more aggressive initial therapy.

  17. Time to sputum conversion in multidrug-resistant tuberculosis patients in Armenia: retrospective cohort study

    Directory of Open Access Journals (Sweden)

    Arax Hovhannesyan

    2012-01-01

    Full Text Available OBJECTIVE: To characterize time to sputum conversion among patients with multidrug resistant tuberculosis who were enrolled into second-line tuberculosis treatment program; to identify risk factors for delayed sputum conversion. DESIGN: Retrospective cohort study designed to identify the factors associated with sputum conversion. Survival analysis was performed using Kaplan-Meier estimator to compute estimates for median time to sputum conversion and Cox proportional hazards model to compute hazard ratios (HR. RESULTS: Sputum conversion from positive to negative was observed in 134 out of 195 cases (69%. Among these who converted the median time to conversion was 3.7 months. Factors independently associated with time to sputum conversion in the proportional hazards model were: male sex (HR=0.51, 95% CI 0.32-0.81, ofloxacin-resistant tuberculosis (HR = 0.45, 95% CI 0.26-0.78 and first period of recruitment into second-line treatment (HR= 0.69, 95% CI 0.47-1.01. CONCLUSION: Time to sputum conversion in patients with multidrug-resistant tuberculosis in Armenia was 5.8 months (range 0.5- 17.0 months. High level of ofloxacin resistance was the main reason for compromised response to treatment. Patients with a poor resistance profile and males should be targeted with more aggressive initial therapy.

  18. Methadone conversion in infants and children: Retrospective cohort study of 199 pediatric inpatients.

    Science.gov (United States)

    Fife, Alexandra; Postier, Andrea; Flood, Andrew; Friedrichsdorf, Stefan J

    2016-01-01

    Methadone administration has increased in pediatric clinical settings. This review is an attempt to ascertain an equianalgesic dose ratio for methadone in the pediatric population using standard adult dose conversion guidelines. US tertiary children's hospital. Hospitalized pediatric patients, 0-18 years of age. A retrospective chart review was conducted for patients who were converted from their initial opioid therapy regimen (morphine, hydromorphone, and/or fentanyl) to methadone. The primary endpoint was whether or not a dose correction was needed for methadone in the 6 days following conversion using standard dose conversion charts for adults. Documented clinical signs of withdrawal, unrelieved pain, or oversedation were examined. The majority (53.7 percent) of the 199 children were converted to methadone on intensive care units prior extubation or postextubation. The mean conversion ratio was 23.7 mg of oral morphine to 1 mg of oral methadone (median, 18.8 mg:1 mg, SD=25.7). Most patients experienced an adequate conversion (n=115, 57.8 percent), while 83 (41.7 percent) appeared undermedicated, and one child was oversedated. There were no associations found with conversion ratios for initial morphine dose, days to conversion, or effect of withdrawal of concomitant agents with potential for withdrawal. Opioid conversion to methadone is commonly practiced at our institution; however, dosing was significantly lower compared to adult conversion ratios, and more than 40 percent of children were undermedicated. The majority of children in this study received opioids for sedation while intubated and ventilated; therefore, safe and efficacious pediatric methadone conversion rates remain unclear. Prospective studies are needed.

  19. Emotion-motion interactions in conversion disorder: an FMRI study.

    Science.gov (United States)

    Aybek, Selma; Nicholson, Timothy R; O'Daly, Owen; Zelaya, Fernando; Kanaan, Richard A; David, Anthony S

    2015-01-01

    To evaluate the neural correlates of implicit processing of negative emotions in motor conversion disorder (CD) patients. An event related fMRI task was completed by 12 motor CD patients and 14 matched healthy controls using standardised stimuli of faces with fearful and sad emotional expressions in comparison to faces with neutral expressions. Temporal changes in the sensitivity to stimuli were also modelled and tested in the two groups. We found increased amygdala activation to negative emotions in CD compared to healthy controls in region of interest analyses, which persisted over time consistent with previous findings using emotional paradigms. Furthermore during whole brain analyses we found significantly increased activation in CD patients in areas involved in the 'freeze response' to fear (periaqueductal grey matter), and areas involved in self-awareness and motor control (cingulate gyrus and supplementary motor area). In contrast to healthy controls, CD patients exhibited increased response amplitude to fearful stimuli over time, suggesting abnormal emotional regulation (failure of habituation / sensitization). Patients with CD also activated midbrain and frontal structures that could reflect an abnormal behavioral-motor response to negative including threatening stimuli. This suggests a mechanism linking emotions to motor dysfunction in CD.

  20. HYLIFE-II power conversion system design and cost study

    International Nuclear Information System (INIS)

    Hoffman, M.A.

    1990-09-01

    The power conversion system for the HYLIFE-2 fusion power plant has been defined to include the IHX's (intermediate heat exchangers) and everything that support the exchange of energy from the reactor. It is referred to simply as the BOP (balance of plant) in the rest of this report. The above is a convenient division between the reactor equipment and the rest of the fusion power plant since the BOP design and cost then depend only on the specification of the thermal power to the IHX's and the temperature of the primary Flibe coolant into and out of the IHX's, and is almost independent of the details of the reactor design. The main efforts during the first year have been on the definition and thermal-hydraulics of the IHX's, the steam generators and the steam power plant, leading to the definition of a reference BOP with the molten salt, Flibe, as the primary coolant. A summary of the key results in each of these areas is given in this report

  1. A study of alternative splicing in the pig

    Directory of Open Access Journals (Sweden)

    Jørgensen Claus B

    2010-05-01

    Full Text Available Abstract Background Since at least half of the genes in mammalian genomes are subjected to alternative splicing, alternative pre-mRNA splicing plays an important contribution to the complexity of the mammalian proteome. Expressed sequence tags (ESTs provide evidence of a great number of possible alternative isoforms. With the EST resource for the domestic pig now containing more than one million porcine ESTs, it is possible to identify alternative splice forms of the individual transcripts in this species from the EST data with some confidence. Results The pig EST data generated by the Sino-Danish Pig Genome project has been assembled with publicly available ESTs and made available in the PigEST database. Using the Distiller package 2,515 EST clusters with candidate alternative isoforms were identified in the EST data with high confidence. In agreement with general observations in human and mouse, we find putative splice variants in about 30% of the contigs with more than 50 ESTs. Based on the criteria that a minimum of two EST sequences confirmed each splice event, a list of 100 genes with the most distinct tissue-specific alternative splice events was generated from the list of candidates. To confirm the tissue specificity of the splice events, 10 genes with functional annotation were randomly selected from which 16 individual splice events were chosen for experimental verification by quantitative PCR (qPCR. Six genes were shown to have tissue specific alternatively spliced transcripts with expression patterns matching those of the EST data. The remaining four genes had tissue-restricted expression of alternative spliced transcripts. Five out of the 16 splice events that were experimentally verified were found to be putative pig specific. Conclusions In accordance with human and rodent studies we estimate that approximately 30% of the porcine genes undergo alternative splicing. We found a good correlation between EST predicted tissue

  2. Study of a condition for the mode conversion from purely perpendicular electrostatic waves to electromagnetic waves

    Energy Technology Data Exchange (ETDEWEB)

    Kalaee, Mohammad Javad, E-mail: mjkalaee@ut.ac.ir [Space Physics Group, Institute of Geophysics, University of Tehran (Iran, Islamic Republic of); Katoh, Yuto, E-mail: yuto@stpp.gp.tohoku.ac.jp [Department of Geophysics, Graduate School of Science, Tohoku University (Japan)

    2016-07-15

    One of the mechanisms for generating electromagnetic plasma waves (Z-mode and LO-mode) is mode conversion from electrostatic waves into electromagnetic waves in inhomogeneous plasma. Herein, we study a condition required for mode conversion of electrostatic waves propagating purely perpendicular to the ambient magnetic field, by numerically solving the full dispersion relation. An approximate model is derived describing the coupling between electrostatic waves (hot plasma Bernstein mode) and Z-mode waves at the upper hybrid frequency. The model is used to study conditions required for mode conversion from electrostatic waves (electrostatic electron cyclotron harmonic waves, including Bernstein mode) into electromagnetic plasma waves (LO-mode). It is shown that for mode conversion to occur in inhomogeneous plasma, the angle between the boundary surface and the magnetic field vector should be within a specific range. The range of the angle depends on the norm of the k vector of waves at the site of mode conversion in the inhomogeneous region. The present study reveals that inhomogeneity alone is not a sufficient condition for mode conversion from electrostatic waves to electromagnetic plasma waves and that the angle between the magnetic field and the density gradient plays an important role in the conversion process.

  3. Weight Estimate and Centers of Gravity for JT-11 Nuclear Conversion Study

    International Nuclear Information System (INIS)

    Manning, R. W.

    1958-01-01

    Weight estimates and centers of gravity for the JT-11 nuclear conversion study are tabulated. Included in the radiator section are: diffuser, shrouds, supports, radiator, liquid metal, shafting and casing.

  4. Impact of cash conversion cycle on cash holding – A study on FMCG sector

    Directory of Open Access Journals (Sweden)

    Somnath Das

    2017-11-01

    Full Text Available In today’s environment, cash conversion cycle is randomly used as a measure of liquidity of the organizations. Cash conversion cycle is considered as the length of time between raw-materials and collection of cash from debtors. It can be used as a benchmarking competitors or comparing companies. On the other hand, Cash holding is one of the most important financial decisions that a manager has to make in any organization. Some organizations hold more cash and some organizations hold less cash. In this study, we perform a survey to make a relationship between Cash Conversion Cycle and Cash Holding.

  5. Experimental study on evaluation and optimization of conversion of waste chicken fat into biodiesel

    International Nuclear Information System (INIS)

    Andrade, J.E.; Sebastian, P.J.; Perez, A.

    2009-01-01

    Full text: This study was initiated to evaluate and optimize the conversion of waste chicken fat (WCF) into ethyl and methyl ester called biodiesel. The physical and chemical characteristics of these esters were much closer to those of Diesel fuel than those of fresh vegetable oil or fat, which makes them a good substitute for Diesel fuel. Experiments have been performed to determine the optimum conditions for this conversion process using a three factor factorial design for producing biodiesel. The major variables in the transesterification process are determined from the pre experiments as: reaction temperature, molar ratio of alcohol/oil, alcohol type utilized and catalyst type. Absolute ethanol was found better than absolute methanol, since ethanol gives higher conversion and less viscosity at all levels, mainly at 100% excess concentration. Temperature had no detectable effect on the ultimate conversion ratio and viscosity for both ester products. However, higher temperatures decreases the time required to reach maximum conversion, which will be at the expense of the cost of energy. An interaction between time and temperature was found for all conversions. Therefore, 60 C was found to be the optimum temperature, and one hour is the optimum time for the conversion of WAFs into biodiesel. The obtained product with 97.02% of biodiesel was analyzed and characterized by gas chromatography. (author)

  6. Improvement of skeleton conversion in ICRP reference phantom conversion project

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Zhao Jun; Yeom, Yeon Soo; Thang, Nguyen Tat; Kim, Han Sung; Han, Min Cheol; Kim, Chan Hyeong [Dept. of Nuclear Engineering, Hanyang University, Seoul (Korea, Republic of); Kim, Seong Hoon [Dept. of Radiation Oncology, College of Medicine, Hanyang University, Seoul (Korea, Republic of)

    2014-11-15

    In the previous skeleton conversion, most bones were directly converted from the ICRP voxel phantoms by using the 3D rendering method whereas several complex-shape bones (cranium, ribs, spines, feet, and hands) were not able to be directly converted. We alternatively employed the corresponding well-defined polygonal models and attempted to adjust them to match the voxel models. However, this approach was unsatisfactory. The shapes of the alternative models were significantly different from those of the voxel models, making it virtually impossible to exactly match the voxel models as shown in Fig. 3 (left). In order to overcome the difficulty in the complex bone conversion, the present study developed a new conversion method and converted these complex bones voxel models of the ICRP male phantom to polygonal models. The present study developed the new conversion method and successfully improved polygonal models for cranium, ribs, and spines for the ICRP male phantom. The new conversion method will be also applied to the complex bone conversion for the ICRP female phantom as well as other complex organ conversion in the future.

  7. Improvement of skeleton conversion in ICRP reference phantom conversion project

    International Nuclear Information System (INIS)

    Wang, Zhao Jun; Yeom, Yeon Soo; Thang, Nguyen Tat; Kim, Han Sung; Han, Min Cheol; Kim, Chan Hyeong; Kim, Seong Hoon

    2014-01-01

    In the previous skeleton conversion, most bones were directly converted from the ICRP voxel phantoms by using the 3D rendering method whereas several complex-shape bones (cranium, ribs, spines, feet, and hands) were not able to be directly converted. We alternatively employed the corresponding well-defined polygonal models and attempted to adjust them to match the voxel models. However, this approach was unsatisfactory. The shapes of the alternative models were significantly different from those of the voxel models, making it virtually impossible to exactly match the voxel models as shown in Fig. 3 (left). In order to overcome the difficulty in the complex bone conversion, the present study developed a new conversion method and converted these complex bones voxel models of the ICRP male phantom to polygonal models. The present study developed the new conversion method and successfully improved polygonal models for cranium, ribs, and spines for the ICRP male phantom. The new conversion method will be also applied to the complex bone conversion for the ICRP female phantom as well as other complex organ conversion in the future

  8. Quantum conversion

    OpenAIRE

    Mazilu, Michael

    2015-01-01

    ICOAM 2015 The electromagnetic momentum transferred transferred to scattering particles is proportional to the intensity of the incident fields, however, the momentum of single photons ℏk does not naturally appear in these classical expressions. Here, we discuss an alternative to Maxwell's stress tensor that renders the classical electromagnetic field momentum compatible to the quantum mechanical one. This is achieved through the introduction of the quantum conversion which allows the tran...

  9. Gene conversion and reversion events in Saccharomyces cerevisiae. Model for study of gamma radiation damage

    International Nuclear Information System (INIS)

    Moreno, Damaris; Fuentes, Jorge L.; Prieto Miranda, Enrique F.; Sanchez Lamar, Angel; Baluja, Ligia

    2004-01-01

    Radiosensitivity and kinetics of induction of gene conversion and reversion events in Saccharomyces cerevisiae strain D7 to gamma radiation at dose ranges from 100 to 800 Gy and 50 to 300 Gy respectively were studied. A source of 60Co PX- -30 at a dose rate of 49,43 GY/min was utilized. The cell survival curve showed DL50 of 150 Gy. Cell death kinetics was linear and adjusted over 98 %. The induction of gene conversion events was significant in relation to control from 50 Gy on. However, gene reversion was significant only at 200 Gy. Generally speaking, gene conversion event frequencies were higher than those of reversion, which indicates that gamma radiation preferably induces recombinogenic events. Both the conversion and reversion events showed exponential dependence on gamma radiation dose. The relative benefits of this test for mutagenesis and anti-mutagenesis studies were debated in this paper

  10. Cash Conversion Cycle, Cash Management and Profitability: An Empirical Study on the ISE Traded Companies

    OpenAIRE

    Tulay Yucel; Gulizar Kurt

    2002-01-01

    This paper investigates the relationship of cash conversion cycle, a tool in working capital management, with profitability, liquidity and debt structure. The data covering the period of 1995-2000, of 167 firms whose stocks are listed on the Istanbul Stock Exchange (ISE). The cash conversion cycle, profitability, liquidity and debt structure were examined comparatively in this study on the basis of period, industry and firm size. It was examined that the relationships of these variables and t...

  11. Quantitative feasibility study of magnetocaloric energy conversion utilizing industrial waste heat

    International Nuclear Information System (INIS)

    Vuarnoz, D.; Kitanovski, A.; Gonin, C.; Borgeaud, Y.; Delessert, M.; Meinen, M.; Egolf, P.W.

    2012-01-01

    Highlights: ► We model magnetic energy conversion machine for the use of industrial waste heat. ► Efficiencies and masses of the system are evaluated by a numerical model. ► Excellent potential of profitability is expected with large low-exergy heat sources. -- Abstract: The main objective of this theoretical study was to investigate under which conditions a magnetic energy conversion device (MECD) – utilizing industrial waste heat – is economically feasible. Furthermore, it was evaluated if magnetic energy conversion (MCE) has the potential of being a serious concurrent to already existing conventional energy conversion technologies. Up-today the availability of magnetocaloric materials with a high Curie temperature and a high magnetocaloric effect is rather limited. Therefore, this study was mainly focused on applications with heat sources of low to medium temperature levels. Magnetic energy conversion machines, containing permanent magnets, are numerically investigated for operation conditions with different temperature levels, defined by industrial waste heat sources and environmental heat sinks, different magnetic field intensities and different frequencies of operation (number of thermodynamic cycles per unit of time). Theoretical modeling and numerical simulations were performed in order to determine thermodynamic efficiencies and the exergy efficiencies as function of different operation conditions. From extracted data of our numerical results, approximate values of the total mass and total volume of magnetic energy conversion machines could be determined. These important results are presented dependent on the produced electric power. An economic feasibility study supplements the scientific study. It shows an excellent potential of profitability for certain machines. The most important result of this article is that the magnetic energy conversion technology can be economically and technically competitive to or even beat conventional energy

  12. Study of vanadium-based chemical conversion coating on the corrosion resistance of magnesium alloy

    International Nuclear Information System (INIS)

    Yang, K.H.; Ger, M.D.; Hwu, W.H.; Sung, Y.; Liu, Y.C.

    2007-01-01

    In this study, magnesium alloy (AZ61) was immersed in vanadium containing bath with various conditions, such as the vanadium concentration, immersion time and bath temperature. The results indicate that increase of both vanadium concentration and immersion time produces a thicker conversion layer. However, when immersion time is too long, it will worsen the corrosion resistance due to the increasing of the crack density. The experimental parameter of bath temperature has no significant effect on corrosion resistance. Our results demonstrated that the better corrosion resistance coating can be obtained when the samples are submitted to an immersion in the conversion bath containing NaVO 3 with concentration of 30 g l -1 for 10 min at 80 deg. C. The presented conversion treatment has its potential to replace the chrome-based conversion coating treatment

  13. Experimental Study on Conversion of Stored Thermal Energy to Mechanical Work in FCI

    International Nuclear Information System (INIS)

    Fujii-e, Y.; Kondo, S.; Mivazaki, K.

    1976-01-01

    In the present study the process how the thermal energy stored in the coolant should be converted into the mechanical work is emphasized as well as the generation of pressure waves, eliminating the complicated problems involved in FCI, such as fragmentation, heat transfer from molten fuel to coolant, etc. A simulation experiment has been performed in a small scale vertical channel using stagnant potassium. Large superheat inherent in liquid metals was utilized as the method to accumulate the thermal energy. The following experimental parameters were chosen to examine their effects on the energy conversion ratio: the heat flux, the cover gas pressure, the liquid column length, the temperature of the upper unheated region and the incipient boiling superheat (corresponding to the stored thermal energy). The results are summarized that the conversion ratio from thermal to kinetic energies has increasing trends with increases of the incipient boiling superheat, the cover gas pressure and the temperature of upper unheated region, ranging over 0.02-0.75% in the present experiment. The important conclusions of the present experiment are summarized as follows. The thermal to kinetic energy conversion ratio n k ranges over 0.02-0.75 % for ΔT s = 10-150 deg.C, estimating from the maximum velocity measured. The thermal to mechanical work conversion ratio n w ranges over 0.14-5.6%. The effect of the heat flux on the both conversion ratios is small within the range covered by the present experiment (g≤133 W/cm 2 ). The effect of the liquid column length is not presented. The thermal to kinetic energy conversion ratio increases with the incipient boiling superheat which corresponds to the stored thermal energy in the present experiment. The both conversion ratio decrease with a decrease of the cover gas pressure. This is attributable to the thermal contact in the upper unheated region. The both conversion ratios increase with an increase in the temperature of the upper

  14. Pengaruh Citra Merek Dan Pengalaman Konsumen Terhadap Loyalitas Konsumen Sepatu Sneaker Merek Converse (Studi Kasus Pada Pengguna Sepatu Sneaker Merek Converse Di Kota Semarang)

    OpenAIRE

    Wicaksono, Aldo Dwi; Nugraha, Hari Susanta

    2017-01-01

    Every company expect to have a high customer loyalty. But, there is a Converse sneakers product sales degression in Semarang City based on observation that also indicate a degression in customer loyalty. Based on observation and theoritical study, that degression supected caused by low brand image factor and low customer experience factor. Therefore, the purpose of this research is to find out the impacts of brand image and cutomer experience towards Converse sneakers cutomer loyalty, both in...

  15. Project on Alternative Systems Study - PASS. Final report

    International Nuclear Information System (INIS)

    1992-10-01

    Alternative repository systems for deep disposal of spent fuel and different types of canisters are studied regarding technical aspects in Project on Alternative System Study (PASS). The objective is to present a ranking of repository systems as well as of canister types for each system. The studies and compared systems are: KBS-3, Medium Long Tunnels (MLH), Long tunnels (VLH) and Deep Boreholes (VDH). For KBS-3 and MLH five canister types are compared (copper/steel, copper/lead, copper (HIP), steel/lead and steel), for VLH two types (copper/steel and steel), and for VDH three types (titanium/concrete with non-consolidated fuel assemblies, titanium/concrete with consolidated assemblies and copper (HIP) with non-consolidated assemblies). The comparison is separated into three sub-comparisons (Technology, Long-term performance and safety, and Costs), which eventually are merged into one ranking. With respect to canister alternatives the result is that the copper/steel canister is ranked first for KBS-3, MLH and VLH, while the titanium/concrete canister is ranked first for VDH (non-consolidated as well as consolidated assemblies. With these canister alternatives the merged ranking of repository systems results in placing KBS-3 slightly in front of MLH. VLH comes thereafter and VDH last. (32 refs.)

  16. Aphasia and Topic Initiation in Conversation: A Case Study

    Science.gov (United States)

    Barnes, Scott E.; Candlin, Christopher N.; Ferguson, Alison

    2013-01-01

    Background: Aphasiologists often research, assess and treat linguistic impairment and its consequences for daily life separately. Studies that link the language used by people with aphasia to routine communicative activities may expand the linguistic forms treated as relevant for successful communication by people with aphasia. Previous research…

  17. A mixed core conversion study with HEU and LEU fuels

    International Nuclear Information System (INIS)

    Matos, J.E.; Freese, K.E.

    1985-01-01

    The results of a mixed core study are presented for gradual replacement of HEU fuel with LEU fuel using the IAEA generic 10 MW reactor as an example. The key parameters show that the transition can be accomplished safely and economically. (author)

  18. Mixed core conversion study with HEU and LEU fuels

    International Nuclear Information System (INIS)

    Matos, J.E.; Freese, K.E.

    1984-01-01

    The results of a mixed core study are presented for gradual replacement of HEU fuel with LEU fuel using the IAEA generic 10 MW reactor as an example. The key parameters show that the transition can be accomplished safely and economically

  19. Task Order 20: Supercritical Carbon Dioxide Brayton Cycle Energy Conversion Study

    Energy Technology Data Exchange (ETDEWEB)

    Murray, Paul [AREVA Federal Services, LLC, Charlotte, NC (United States); Lindsay, Edward [AREVA Federal Services, LLC, Charlotte, NC (United States); McDowell, Michael [AREVA Federal Services, LLC, Charlotte, NC (United States); Huang, Megan [AREVA Federal Services, LLC, Charlotte, NC (United States)

    2015-04-23

    AREVA Inc. developed this study for the US Department of Energy (DOE) office of Nuclear Energy (NE) in accordance with Task Order 20 Statement of Work (SOW) covering research and development activities for the Supercritical Carbon Dioxide (sCO2) Brayton Cycle energy conversion. The study addresses the conversion of sCO2 heat energy to electrical output by use of a Brayton Cycle system and focuses on the potential of a net efficiency increase via cycle recuperation and recompression stages. The study also addresses issues and study needed to advance development and implementation of a 10 MWe sCO2 demonstration project.

  20. Report on the Savannah River Site aluminum-based spent nuclear fuel alternatives cost study

    International Nuclear Information System (INIS)

    1998-12-01

    Initial estimates of costs for the interim management and disposal of aluminum-based spent nuclear fuel (SNF) were developed during preparation of the Environmental Impact Statement (EIS) on the Nuclear Weapons Nonproliferation Policy Concerning Foreign Research Reactor Spent Nuclear Fuel. The Task Team evaluated multiple alternatives, assessing programmatic, technical, and schedule risks, and generated life-cycle cost projections for each alternative. The eight technology alternatives evaluated were: direct co-disposal; melt and dilute; reprocessing; press and dilute; glass material oxidation dissolution system (GMODS); electrometallurgical treatment; dissolve and vitrify; and plasma arc. In followup to the Business Plan that was developed to look at SNF dry storage, WSRC prepared an addendum to the cost study. This addendum estimated the costs for the modification and use of an existing (105L) reactor facility versus a greenfield approach for new facilities (for the Direct Co-Disposal and Melt and Dilute alternatives). WSRC assessed the impacts of a delay in reprocessing due to the potential reservation of H-Canyon for other missions (i.e., down blending HEU for commercial use or the conversion of plutonium to either MOX fuel or an immobilized repository disposal form). This report presents the relevant results from these WSRC cost studies, consistent with the most recent project policy, technology implementation, canyon utilization, and inventory assumptions. As this is a summary report, detailed information on the technical alternatives or the cost assumptions raised in each of the above-mentioned cost studies is not provided. A comparison table that briefly describes the bases used for the WSRC analyses is included as Appendix A

  1. Study of Catalyst Variation Effect in Glycerol Conversion Process to Hydrogen Gas by Steam Reforming

    Science.gov (United States)

    Widayat; Hartono, R.; Elizabeth, E.; Annisa, A. N.

    2018-04-01

    Along with the economic development, needs of energy being increase too. Hydrogen as alternative energy has many usages. Besides that, hydrogen is one source of energy that is a clean fuel, but process production of hydrogen from natural gas as a raw material has been used for a long time. Therefore, there is need new invention to produce hydrogen from the others raw material. Glycerol, a byproduct of biodiesel production, is a compound which can be used as a raw material for hydrogen production. By using glycerol as a raw material of hydrogen production, we can get added value of glycerol as well as an energy source solution. The process production of hydrogen by steam reforming is a thermochemical process with efficiency 70%. This process needs contribution of catalyst to improve its efficiency and selectivity of the process. In this study will be examined the effect variation of catalyst for glycerol conversion process to hydrogen by steam reforming. The method for catalyst preparation was variation of catalyst impregnation composition, catalyst calcined with difference concentration of hydrochloric acid and calcined with difference hydrochloric acid ratio. After that, all of catalyst which have been prepared, used for steam reforming process for hydrogen production from glycerol as a raw material. From the study, the highest yield of hydrogen gas showed in the process production by natural zeolite catalyst with 1:15 Hydrochloric acid ratio was 42.28%. Hydrogen yield for 2M calcined natural zeolite catalyst was 38.37%, for ZSM-5 catalyst was 15.83%, for 0.5M calcined natural zeolite was 13.09% and for ultrasonic natural zeolite was 11.43%. The lowest yield of hydrogen gas showed in catalyst 2Zn/ZSM-5 with 11.22%. This result showed that hydrogen yield product was affected by catalyst variation because of the catalyst has difference characteristic and difference catalytic activity after the catalyst preparation process.

  2. Achieving consensus on the definition of conversion to laparotomy: a Delphi study among general surgeons, gynecologists, and urologists

    NARCIS (Netherlands)

    Blikkendaal, Mathijs D.; Twijnstra, Andries R. H.; Stiggelbout, Anne M.; Beerlage, Harrie P.; Bemelman, Willem A.; Jansen, Frank Willem

    2013-01-01

    In laparoscopic surgery, conversion to laparotomy is associated with worse clinical outcomes, especially if the conversion is due to a complication. Although apparently important, no commonly used definition of conversion exists. The aim of this study was to achieve multidisciplinary consensus on a

  3. Exhaust energy conversion by thermoelectric generator: Two case studies

    International Nuclear Information System (INIS)

    Karri, M.A.; Thacher, E.F.; Helenbrook, B.T.

    2011-01-01

    This study reports predictions of the power and fuel savings produced by thermoelectric generators (TEG) placed in the exhaust stream of a sports utility vehicle (SUV) and a stationary, compressed-natural-gas-fueled engine generator set (CNG). Results are obtained for generators using either commercially-available bismuth telluride (Bi 2 Te 3 ) or quantum-well (QW) thermoelectric material. The simulated tests are at constant speed in the SUV case and at constant AC power load in the CNG case. The simulations make use of the capabilities of ADVISOR 2002, the vehicle modeling system, supplemented with code to describe the thermoelectric generator system. The increase in power between the QW- and Bi 2 Te 3 -based generators was about three times for the SUV and seven times for the CNG generator under the same simulation conditions. The relative fuel savings for the SUV averaged around -0.2% using Bi 2 Te 3 and 1.25% using QW generators. For the CNG case the fuel savings was around 0.4% using Bi 2 Te 3 and around 3% using QW generators. The negative fuel gains in the SUV were caused by parasitic losses. The power to transport the TEG system weight was the dominant parasitic loss for the SUV but was absent in the CNG generator. The lack of space constraint and the absence of parasitic loss from the TEG system weight in the CNG case allowed an increase in the TEG system size to generate more power.

  4. Exhaust energy conversion by thermoelectric generator: Two case studies

    Energy Technology Data Exchange (ETDEWEB)

    Karri, M.A.; Thacher, E.F.; Helenbrook, B.T. [Department of Mechanical and Aeronautical Engineering, PO Box 5725, Clarkson University, Potsdam, NY 13699 (United States)

    2011-03-15

    This study reports predictions of the power and fuel savings produced by thermoelectric generators (TEG) placed in the exhaust stream of a sports utility vehicle (SUV) and a stationary, compressed-natural-gas-fueled engine generator set (CNG). Results are obtained for generators using either commercially-available bismuth telluride (Bi{sub 2}Te{sub 3}) or quantum-well (QW) thermoelectric material. The simulated tests are at constant speed in the SUV case and at constant AC power load in the CNG case. The simulations make use of the capabilities of ADVISOR 2002, the vehicle modeling system, supplemented with code to describe the thermoelectric generator system. The increase in power between the QW- and Bi{sub 2}Te{sub 3}-based generators was about three times for the SUV and seven times for the CNG generator under the same simulation conditions. The relative fuel savings for the SUV averaged around -0.2% using Bi{sub 2}Te{sub 3} and 1.25% using QW generators. For the CNG case the fuel savings was around 0.4% using Bi{sub 2}Te{sub 3} and around 3% using QW generators. The negative fuel gains in the SUV were caused by parasitic losses. The power to transport the TEG system weight was the dominant parasitic loss for the SUV but was absent in the CNG generator. The lack of space constraint and the absence of parasitic loss from the TEG system weight in the CNG case allowed an increase in the TEG system size to generate more power. (author)

  5. B cell remote-handled waste shipment cask alternatives study

    International Nuclear Information System (INIS)

    RIDDELLE, J.G.

    1999-01-01

    The decommissioning of the 324 Facility B Cell includes the onsite transport of grouted remote-handled radioactive waste from the 324 Facility to the 200 Areas for disposal. The grouted waste has been transported in the leased ATG Nuclear Services 3-82B Radioactive Waste Shipping Cask (3-82B cask). Because the 3-82B cask is a U.S. Nuclear Regulatory Commission (NRC)-certified Type B shipping cask, the lease cost is high, and the cask operations in the onsite environment may not be optimal. An alternatives study has been performed to develop cost and schedule information on alternative waste transportation systems to assist in determining which system should be used in the future. Five alternatives were identified for evaluation. These included continued lease of the 3-82B cask, fabrication of a new 3-82B cask, development and fabrication of an onsite cask, modification of the existing U.S. Department of Energy-owned cask (OH-142), and the lease of a different commercially available cask. Each alternative was compared to acceptance criteria for use in the B Cell as an initial screening. Only continued leasing of the 3-82B cask, fabrication of a new 3-82B cask, and the development and fabrication of an onsite cask were found to meet all of the B Cell acceptance criteria

  6. Uranium conversion

    International Nuclear Information System (INIS)

    Oliver, Lena; Peterson, Jenny; Wilhelmsen, Katarina

    2006-03-01

    FOI, has performed a study on uranium conversion processes that are of importance in the production of different uranium compounds in the nuclear industry. The same conversion processes are of interest both when production of nuclear fuel and production of fissile material for nuclear weapons are considered. Countries that have nuclear weapons ambitions, with the intention to produce highly enriched uranium for weapons purposes, need some degree of uranium conversion capability depending on the uranium feed material available. This report describes the processes that are needed from uranium mining and milling to the different conversion processes for converting uranium ore concentrate to uranium hexafluoride. Uranium hexafluoride is the uranium compound used in most enrichment facilities. The processes needed to produce uranium dioxide for use in nuclear fuel and the processes needed to convert different uranium compounds to uranium metal - the form of uranium that is used in a nuclear weapon - are also presented. The production of uranium ore concentrate from uranium ore is included since uranium ore concentrate is the feed material required for a uranium conversion facility. Both the chemistry and principles or the different uranium conversion processes and the equipment needed in the processes are described. Since most of the equipment that is used in a uranium conversion facility is similar to that used in conventional chemical industry, it is difficult to determine if certain equipment is considered for uranium conversion or not. However, the chemical conversion processes where UF 6 and UF 4 are present require equipment that is made of corrosion resistant material

  7. Development of an integrated optimization method for analyzing effect of energy conversion efficiency under uncertainty – A case study of Bayingolin Mongol Autonomous Prefecture, China

    International Nuclear Information System (INIS)

    Jin, S.W.; Li, Y.P.; Huang, G.H.; Hao, Q.; Nie, S.

    2015-01-01

    Highlights: • Superiority–inferiority full-infinite mixed-integer method is developed. • The method can tackle uncertainties of fuzzy sets, crisp and functional intervals. • The method is applied to a real case of planning energy system. • Effects of energy-conversion efficiency on energy systems are analyzed. • Results can support policy enactment of conversion efficiency improvement. - Abstract: In this study, a superiority–inferiority full-infinite mixed-integer programming (SFMP) method is developed for analyzing the effect of energy conversion efficiency under uncertainty. SFMP can effectively tackle uncertainties expressed as fuzzy sets, crisp intervals and functional intervals, it also can directly reflect relationships among multiple fuzzy sets through varying superiority and inferiority degrees with a high computational efficiency. Then the developed SFMP is applied to a real case of planning energy system for Bayingolin Mongol Autonomous Prefecture, where multiple scenarios related to different energy-conversion efficiency are concerned. Results for energy processing, energy conversion, capacity expansion, pollutant emission and system cost have been generated. It is proved that SFMP is an effective approach to deal with the uncertainties in energy systems with interactive and uncertain characteristics. A variety of uncertainties existed in energy conversion processes and impact factors could affect the modeling result. Results show that improvement of energy-conversion efficiency can effectively facilitate reducing energy resources consumption, optimizing energy generation pattern, decreasing capacity expansion, as well as mitigating pollutant emissions. Results also reveal that, for the study area, electric power has a highest energy saving potential among heating, oil processing, coal washing and refining. Results can help decision makers to generate desired alternatives that can facilitate policy enactment of conversion efficiency

  8. Alternatives to the face-to-face consultation in general practice: focused ethnographic case study.

    Science.gov (United States)

    Atherton, Helen; Brant, Heather; Ziebland, Sue; Bikker, Annemieke; Campbell, John; Gibson, Andy; McKinstry, Brian; Porqueddu, Tania; Salisbury, Chris

    2018-04-01

    NHS policy encourages general practices to introduce alternatives to the face-to-face consultation, such as telephone, email, e-consultation systems, or internet video. Most have been slow to adopt these, citing concerns about workload. This project builds on previous research by focusing on the experiences of patients and practitioners who have used one or more of these alternatives. To understand how, under what conditions, for which patients, and in what ways, alternatives to face-to-face consultations present benefits and challenges to patients and practitioners in general practice. Focused ethnographic case studies took place in eight UK general practices between June 2015 and March 2016. Non-participant observation, informal conversations with staff, and semi-structured interviews with staff and patients were conducted. Practice documents and protocols were reviewed. Data were analysed through charting and the 'one sheet of paper' mind-map method to identify the line of argument in each thematic report. Case study practices had different rationales for offering alternatives to the face-to-face consultation. Beliefs varied about which patients and health issues were suitable. Co-workers were often unaware of each other's practice; for example, practice policies for use of e-consultations systems with patients were not known about or followed. Patients reported benefits including convenience and access. Staff and some patients regarded the face-to-face consultation as the ideal. Experience of implementing alternatives to the face-to-face consultation suggests that changes in patient access and staff workload may be both modest and gradual. Practices planning to implement them should consider carefully their reasons for doing so and involve the whole practice team. © British Journal of General Practice 2018.

  9. Antecedents of hospital ownership conversions, mergers, and closures.

    Science.gov (United States)

    Sloan, Frank A; Ostermann, Jan; Conover, Christopher J

    2003-01-01

    This study assesses the determinants of conversions in hospital ownership from 1986 through 1996. To place such changes in context, we also analyze causes of hospital mergers and closures, which are often alternatives to hospital ownership conversion. A consistent result from our analysis is that an important antecedent of ownership conversions is a low profit margin. Conversions from private nonprofit or government ownership to for-profit status are preceded by chronically low margins and high debt-to-asset ratios. By contrast, conversions from for-profit ownership occur quickly following declines in margins. Many mergers seem motivated by a desire to increase market power--a consideration not evident for conversions.

  10. Does vitamin D deficiency predict early conversion of clinically isolated syndrome? A preliminary Egyptian study.

    Science.gov (United States)

    Shaheen, Hala A; Sayed, Sayed S; Daker, Lamiaa I; AbdelAziz, Hossam Eldin; Taha, Mohamed A

    2018-03-15

    It has been suggested that vitamin D influences the immunoregulation and subsequently affects the risk for conversion of clinically isolated syndrome (CIS) to clinically definite multiple sclerosis (MS). There is little information regarding the relationship between levels of vitamin D and CIS conversion to MS in Egyptian patients. It is to study contribution of vitamin D deficiency to conversion of CIS to clinically definite multiple sclerosis (CDMS) and correlation of vitamin D level to cognitive and magnetic resonance imaging (MRI) results. A longitudinal prospective case control study was conducted on 43 Egyptian patients diagnosed as CIS according to McDonald criteria (2010). Clinical presentation, brain MRI and 25-hydroxyvitamin D levels were evaluated at baseline and after one-year follow-up. The CIS patients that converted to MS showed significant lower vitamin D level (p < 0.001) than the non-convertors. Multivariate logistic regression analysis revealed that the CIS patients with lower 25-hydroxyvitamin D level (p < 0.001) are at higher risk for early conversion to MS. There was a significant positive correlation between the vitamin D level and PASAT (r = 0.36, p = 0.02). It was found that there was a significant negative correlation between vitamin D level and MRI T 2 load (r = -0.38, p = 0.01). The low level of 25-hydroxyvitamin D may predict early conversion to clinically definite MS. Early vitamin D supplementation is recommended in patients with CIS.

  11. Experimental Study of Heat Energy Absorber with Porous Medium for Thermoelectric Conversion System

    Directory of Open Access Journals (Sweden)

    Tzer-Ming Jeng

    2013-12-01

    Full Text Available The thermoelectric conversion system usually consists of the heat absorber, the thermoelectric generator (TEG and the heat sink, while the heat absorber collects the heat to increase the temperature on the hot surface of TEG and enhances the generating electricity. This study experimentally investigated the performance of the brass-beads packed-bed heat absorber for the thermoelectric conversion system. The packed-bed heat absorber is installed in a square channel with the various flow orientation systems and the small ratio of channel width to bead diameter. The flow orientation systems included the straight flow and jet flow systems. This study showed the local and average heat transfer characteristics for various parameters. The experimental results can be the base of designs for the novel porous heat absorber of the thermoelectric conversion system.

  12. Alternative kynurenic acid synthesis routes studied in the rat cerebellum

    Directory of Open Access Journals (Sweden)

    Tonali eBlanco Ayala

    2015-05-01

    Full Text Available Kynurenic acid (KYNA, an astrocyte-derived, endogenous antagonist of α7 nicotinic acetylcholine and excitatory amino acid receptors, regulates glutamatergic, GABAergic, cholinergic and dopaminergic neurotransmission in several regions of the rodent brain. Synthesis of KYNA in the brain and elsewhere is generally attributed to the enzymatic conversion of L-kynurenine (L-KYN by kynurenine aminotransferases (KATs. However, alternative routes, including KYNA formation from D-kynurenine (D-KYN by D-amino acid oxidase (DAAO and the direct transformation of kynurenine to KYNA by reactive oxygen species (ROS, have been demonstrated in the rat brain. Using the rat cerebellum, a region of low KAT activity and high DAAO activity, the present experiments were designed to examine KYNA production from L-KYN or D-KYN by KAT and DAAO, respectively, and to investigate the effect of ROS on KYNA synthesis. In chemical combinatorial systems, both L-KYN and D-KYN interacted directly with peroxynitrite (ONOO- and hydroxyl radicals (OH•, resulting in the formation of KYNA. In tissue homogenates, the non-specific KAT inhibitor aminooxyacetic acid (AOAA; 1 mM reduced KYNA production from L-KYN and D-KYN by 85.1 ± 1.7% and 27.1 ± 4.5%, respectively. Addition of DAAO inhibitors (benzoic acid, kojic acid or 3-methylpyrazole-5-carboxylic acid; 5 µM each attenuated KYNA formation from L-KYN and D-KYN by ~35% and ~66%, respectively. ONOO- (25 µM potentiated KYNA production from both L-KYN and D-KYN, and these effects were reduced by DAAO inhibition. AOAA attenuated KYNA production from L-KYN + ONOO- but not from D-KYN + ONOO-. In vivo, extracellular KYNA levels increased rapidly after perfusion of ONOO- and, more prominently, after subsequent perfusion with L-KYN or D-KYN (100 µM. Taken together, these results suggest that different mechanisms are involved in KYNA production in the rat cerebellum, and that, specifically, DAAO and ROS can function as alternative routes

  13. An in situ study of zirconium-based conversion treatment on zinc surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Taheri, P. [Materials innovation institute (M2i), Elektronicaweg 25, 2628 XG Delft (Netherlands); Delft University of Technology, Department of Materials Science and Engineering, Mekelweg 2, 2628 CD Delft (Netherlands); Laha, P. [Vrije Universiteit Brussel, Department of Electrochemical and Surface Engineering, Pleinlaan 2, B-1050 Brussels (Belgium); Terryn, H. [Delft University of Technology, Department of Materials Science and Engineering, Mekelweg 2, 2628 CD Delft (Netherlands); Vrije Universiteit Brussel, Department of Electrochemical and Surface Engineering, Pleinlaan 2, B-1050 Brussels (Belgium); Mol, J.M.C., E-mail: J.M.C.Mol@tudelft.nl [Delft University of Technology, Department of Materials Science and Engineering, Mekelweg 2, 2628 CD Delft (Netherlands)

    2015-11-30

    Highlights: • We investigated the deposition mechanism of zirconium conversion layer on zinc. • In situ FTIR and electrochemical measurements are conducted. • The initial hydroxyl fraction plays an important role in the deposition process. • Deposition starts with hydroxyl removal by fluoride ions. • An increase of alkalinity adjacent to the surface promotes deposition of Zr. - Abstract: This study is focused on the deposition process of zirconium-based conversion layers on Zn surfaces. The analysis approach is based on a Kretschmann configuration in which in situ ATR-FTIR spectroscopy is combined with open circuit potential (OCP) and near surface pH measurements. Differently pretreated Zn surfaces were subjected to conversion treatments, while the Zr-based deposition mechanism was probed in situ. It was found that the initial hydroxyl fraction promotes the overall Zr conversion process as the near surface pH values are influenced by the initial hydroxyl fraction. Kinetics of the early surface activation and the subsequent Zr-based conversion process are discussed and correlated to the initial hydroxyl fractions.

  14. Engineering study: disposition of terminal liquors for interim storage. [Eight alternative processes

    Energy Technology Data Exchange (ETDEWEB)

    Metz, W.P.; Ogren, W.E.

    1975-02-01

    Eight alternative processes were chosen as being technologically feasible within the time frame dictated by budgeting procedures and terminal liquor availability. Solidified waste products acceptable for single-shell tank storage were assumed to be placed in available single-shell tanks. Double-shell tanks were used only for the more mobile terminal liquors or semi-solid mush products. The mush, chemical neutralization, and clay in-tank processes offer potential savings of tens of millions of dollars over double-shell tank storage of terminal liquors. In order to achieve this cost savings, the process development and demonstration must be completed prior to the beginning of double-shell tank construction (Dec. 1976) expected to be funded from a fiscal year 1977 line item. Budgeting for these additional double-shell tanks must proceed since the processing options discussed here are not yet available and may not prove to be available at the required time. This study indicates the following topics for additional study: Process technology development to achieve interim storage of terminal liquor products receives the greatest emphasis as a means of reducing capital expenditures. Interim storage product criteria, waste inventory, and conversion to final form require definition to allow comparison of the alternatives for disposition of terminal liquors. The pseudotechnical nature of product acceptability criteria is important to the evaluation of the partial neutralization and aluminum removal alternatives. More accurate estimates of terminal liquor quantity and composition are required to give a sound technical basis for choosing the appropriate processing alternative. Retrieval and reprocessing operations may affect the comparisons presented by this study. (DLC)

  15. A kinetic study on the conversion of glucose to levulinic acid

    NARCIS (Netherlands)

    Girisuta, B; Janssen, LPBM; Heeres, HJ

    Levulinic acid has been identified as a promising green. biomass derived platform chemical. A kinetic study oil one of the key steps in the conversion of biomass to levulinic acid, i.e., the acid catalysed decomposition of glucose to levulinic acid has been performed. The experiments were Performed

  16. Green chemicals : A Kinetic Study on the Conversion of Glucose to Levulinic Acid

    NARCIS (Netherlands)

    Girisuta, B.; Janssen, L.P.B.M.; Heeres, H.J.

    2006-01-01

    Levulinic acid has been identified as a promising green, biomass derived platform chemical. A kinetic study on one of the key steps in the conversion of biomass to levulinic acid, i.e., the acid catalysed decomposition of glucose to levulinic acid has been performed. The experiments were performed

  17. Facilitating an L2 Book Club: A Conversation-Analytic Study of Task Management

    Science.gov (United States)

    Ro, Eunseok

    2018-01-01

    This study employs conversation analysis to examine a facilitator's interactional practices in the post-expansion phase of students' presentations in the context of a book club for second language learning. The analysis shows how the facilitator establishes intersubjectivity with regard to the ongoing task and manages students' task performance.…

  18. A sanctuary of safety: A study of how patients with dual diagnosis experience caring conversations.

    Science.gov (United States)

    Priebe, Åsa; Wiklund Gustin, Lena; Fredriksson, Lennart

    2018-04-01

    The prevalence of dual diagnosis, that is, the combination of psychiatric illnesses and substance use disorders, is high. As a vast majority of previous research in this context focusses on the effects of different treatment methods, rather than interpersonal issues, the purpose of the present study was to explore and illuminate in what way patients with a dual diagnosis experience conversations with nurses in an outpatient clinic to be caring. Five patients were interviewed regarding their experiences of caring conversations. The analysis and interpretation were inspired by a previously-used hermeneutical process. These yielded three themes: (i) reciprocity creates safety and communion; (ii) suffering is made visible and understandable; and (iii) self-esteem is restored. When synthesized, these themes gave rise to a main theme - a sanctuary of safety - where suffering is alleviated and dignity and self-esteem are restored. It is concluded that the caring conversation contributes to experiences of safeness. In this specific context, safety appears to be more fundamental than trust for patients' recoveries. The caring conversation also contributes to recovery, as it supports the individual's learning and understanding as a way to cope with problems, which also enables patients to make informed decisions about their own care. The caring conversation contributes to the alleviation of suffering and restoration of dignity and self-esteem for patients with a dual diagnosis. However, there is a need for further research focussing on how the caring conversation can contribute to psychiatric nurses' caring expertise. © 2017 Australian College of Mental Health Nurses Inc.

  19. Study of alternative methods for the management of liquid scintillation counting wastes

    International Nuclear Information System (INIS)

    Roche-Farmer, L.

    1980-02-01

    The Nuclear Engineering Waste Disposal Site in Richland, Washington, is the only radioactive waste disposal facility that will accept liquid scintillation counting wastes (LSCW) for disposal. That site is scheduled to discontinue receiving LSCW by the end of 1982. This document explores alternatives presently available for management of LSCW: evaporation, distillation, solidification, conversion, and combustion

  20. Conversational sensing

    Science.gov (United States)

    Preece, Alun; Gwilliams, Chris; Parizas, Christos; Pizzocaro, Diego; Bakdash, Jonathan Z.; Braines, Dave

    2014-05-01

    Recent developments in sensing technologies, mobile devices and context-aware user interfaces have made it pos- sible to represent information fusion and situational awareness for Intelligence, Surveillance and Reconnaissance (ISR) activities as a conversational process among actors at or near the tactical edges of a network. Motivated by use cases in the domain of Company Intelligence Support Team (CoIST) tasks, this paper presents an approach to information collection, fusion and sense-making based on the use of natural language (NL) and controlled nat- ural language (CNL) to support richer forms of human-machine interaction. The approach uses a conversational protocol to facilitate a ow of collaborative messages from NL to CNL and back again in support of interactions such as: turning eyewitness reports from human observers into actionable information (from both soldier and civilian sources); fusing information from humans and physical sensors (with associated quality metadata); and assisting human analysts to make the best use of available sensing assets in an area of interest (governed by man- agement and security policies). CNL is used as a common formal knowledge representation for both machine and human agents to support reasoning, semantic information fusion and generation of rationale for inferences, in ways that remain transparent to human users. Examples are provided of various alternative styles for user feedback, including NL, CNL and graphical feedback. A pilot experiment with human subjects shows that a prototype conversational agent is able to gather usable CNL information from untrained human subjects.

  1. Conversation analysis and the study of social institutions: methodological, socio-cultural and epistemic considerations

    OpenAIRE

    Roca-Cuberes, Carles

    2014-01-01

    The objective of this study is to show how conversation analysis, a sociological discipline, approaches the study of social institutions. Social institutions are conceived as the crystallization of members’ communicative, interactional practices. Two institutional domains—psychiatric interviews and broadcast news interviews —and a specific interactional practice—‘formulations’—are examined in this study. The results show that (1) in psychiatric interviews the psychiatrist uses formulations to...

  2. Conversations about mental states and theory of mind development during middle childhood: A training study.

    Science.gov (United States)

    Bianco, Federica; Lecce, Serena; Banerjee, Robin

    2016-09-01

    Despite 30years of productive research on theory of mind (ToM), we still know relatively little about variables that influence ToM development during middle childhood. Recent experimental studies have shown that conversations about the mind affect ToM abilities, but they have not explored the mechanisms underlying this developmental effect. In the current study, we examined two potential mechanisms through which conversations about mental states are likely to influence ToM: an increased frequency of references to mental states when explaining behavior and an increased accuracy of mental-state attributions. To this aim, we conducted a training study in which 101 children were assigned to either an intervention condition or a control condition. The conversation-based intervention was made up of four sessions scheduled over 2weeks. Children completed a battery of assessments before and after the intervention as well as 2months later. The groups were equivalent at Time 1 (T1) for age, family affluence, vocabulary, and executive functions. The ToM group showed an improvement in ToM skills (as evaluated on both the practiced tasks and a transfer task). Mediation analyses demonstrated that the accuracy of mental-state attributions, but not the mere frequency of mental-state references, mediated the positive effect of conversations about the mind on ToM development. Our results indicate that conversational experience can enhance mental-state reasoning not by simply drawing children's attention to mental states but rather by scaffolding a mature understanding of social situations. Copyright © 2015 Elsevier Inc. All rights reserved.

  3. Studies on conversion of crude sodium diuranate to high purity uranium oxide by chemical route

    International Nuclear Information System (INIS)

    Rajan, K.C.; Ramadevi, G.; Giri, Nitai; Chakravartty, J.K.; Sreenivas, T.

    2016-01-01

    Uranium values are recovered from ores and mine rejects by employing chemical processing methods. The process chemistry could be either acidic (H 2 SO 4 medium) or alkaline (Na 2 CO 3 - NaHCO 3 medium) based depending on the nature of host rock. The end product is termed as 'yellow cake' which is sent to refining plants for final purification and fuel manufacture. Conventionally the yellow cake product is magnesium (MDU) or ammonium diuranate (ADU) in U-plants following the acidic processing route while it is sodium diuranate (SDU) in the alkaline route. The preference for SDU in plants operating with alkaline route is mainly driven by the requirement of conserving and reusing the expensive chemicals. Though alkaline processing gives relatively purer diuranate product, the practice of direct precipitation of dissolved uranium from pregnant leach liquors invariably leads to presence of impurities detrimental for downstream unit operations, mostly in solvent extraction based refining stages. In this score uranium peroxide is superior to other uranates in many respects. Two alternatives are practiced for the conversion of SDU to uranium peroxide - chemical and fluid bed precipitation. Though generic flowsheet for the conversion stage is well documented, the process conditions and complexities vary with the chemistry of the pregnant leach liquor which is specific for a given ore or a deposit. This paper discusses the process scheme tailored, optimized and tested on a kilo-gram scale for chemical conversion of SDU produced by alkaline processing of a low-grade carbonate hosted uranium ore. The entire process scheme is first of its kind in Indian uranium ore processing arena

  4. Spectrally shaped broadband study of up-conversion in Y2O3:Er3+

    International Nuclear Information System (INIS)

    Lytle, A.L.; Gagnon, E.; Tulchinsky, L.; Krebs, J.K.

    2014-01-01

    We present a novel scheme for studying up-conversion through excited state absorption (ESA) by using a broadband excitation source with spectral shaping capabilities. Up-conversion processes have typically been investigated using a single, narrowband excitation source, when the two steps of the process are coincident in frequency, which is often made possible by broadening mechanisms of the intermediate excited state manifolds. Thus, narrowband sources are limited in the systems they can excite and what material information they can provide. With broadband light, we are able to drive up-conversion with non-coincident frequencies as well. Finally, by windowing the spectrum, we determine the optimal excitation bandwidth for low-concentration (1%) Y 2 O 3 :Er 3+ nanocrystals. - Highlights: • Broadband excitation light is used to drive up-conversion in Y 2 O 3 :Er 3+ . • Broadband light excites all available transitions in the two-photon process. • A spectral shaping technique is used to alter the excitation frequencies present. • The optimal excitation bandwidth is measured by windowing the spectrum. • Broadband excitation reveals information inaccessible by narrowband sources

  5. Study on conversion relationships of compressive strength indexes for recycled lightweight aggregate concrete

    Science.gov (United States)

    Zhang, Xiang-gang; Yang, Jian-hui; Kuang, Xiao-mei

    2017-01-01

    In order to study cube compressive strength and axial compressive strength of recycled lightweight aggregate concrete(RLAC), and conversion relationship between the two, with the replacement rate of recycled lightweight coarse aggregate as change parameters, 15 standard cube test specimens and 15 standard prism test specimens were produced to carry out the test. Then compressive strength of test specimens were measured, and the law of different replacement rate of recycled lightweight coarse aggregate influencing compressive strength of RLAC was analyzed, as the method of statistical regression adopted, the conversion relationships between of cube compressive strength and axial compressive strength of RLAC was obtained. It is shown that compressive strength of RLAC are lower than compressive strength of ordinary concrete; and that compressive strength of RLAC gradually decreases as replacement rate of recycled lightweight coarse aggregate increases; as well as, the conversion relationship between axial compressive strength and cube compressive strength of RLAC is different from ordinary concrete; based on the experimental data, conversion relationship formula between compressive strength indexes of RLAC was established. It is suggested that the replacement rate of recycled lightweight aggregate should be controlled within 25%.

  6. Hearsay Ethnography: Conversational Journals as a Method for Studying Culture in Action.

    Science.gov (United States)

    Watkins, Susan Cotts; Swidler, Ann

    2009-04-01

    Social scientists have long struggled to develop methods adequate to their theoretical understanding of meaning as collective and dynamic. While culture is widely understood as an emergent property of collectivities, the methods we use keep pulling us back towards interview-situated accounts and an image of culture as located in individual experience. Scholars who seek to access supra-individual semiotic structures by studying public rituals and other collectively-produced texts then have difficulty capturing the dynamic processes through which such meanings are created and changed in situ. To try to capture more effectively the way meaning is produced and re-produced in everyday life, we focus here on conversational interactions-the voices and actions that constitute the relational space among actors. Conversational journals provide us with a method: the analysis of texts produced by cultural insiders who keep journals of who-said-what-to-whom in conversations they overhear or events they participate in during the course of their daily lives. We describe the method, distinguishing it from other approaches and noting its drawbacks. We then illustrate the methodological advantages of conversational journals with examples from our texts. We end with a discussion of the method's potential in our setting as well as in other places and times.

  7. Conversion to belatacept in maintenance kidney-transplant patients: A retrospective multicenter European study.

    Science.gov (United States)

    Darres, Amandine; Ulloa, Camillo; Brakemeier, Susanne; Garrouste, Cyril; Bestard, Oriol; Del Bello, Arnaud; Sberro Soussan, Rebecca; Dürr, Michael; Budde, Klemens; Legendre, Christophe; Kamar, Nassim

    2018-03-22

    The use of belatacept is not yet approved for maintenance kidney-transplant patients. This retrospective multicenter European study aimed to assess the efficacy and safety of conversion to belatacept in a large cohort of patients in a real-life setting, and to identify the predictive factors for improved kidney function after the switch. Two-hundred and nineteen maintenance kidney-transplant patients from 5 European kidney-transplant centers were converted to belatacept at 21.2 (0.1-337.1) months posttransplantation, mainly because of impaired kidney function. Thirty-two patients were converted to belatacept within the first 3 months posttransplantation. The mean duration of follow-up was 21.9±20.2 months. The actuarial rate of patients still on belatacept-based therapy was 77.6%. Mean estimated glomerular-filtration rate (eGFR) increased from 32±16.4 at baseline to 38±20 mL/min/1.73 m (ppredictive factor for a significant increase in eGFR (of 5 and 10 mL/min/1.73 m at 3 and 12 months after the switch, respectively). Eighteen patients (8.2%) presented with an acute-rejection episode after conversion; 3 developed a donor-specific antibody (DSA). Overall efficacy and safety were good, including for the 35 patients that had a DSA at conversion. The conversion to belatacept was effective, especially when performed early after transplantation.

  8. Evaluation of hybrid power system alternatives: a case study

    International Nuclear Information System (INIS)

    Rosenthal, Andrew L.

    1999-01-01

    Pursuant to executive and statutory policies, the National Park Service (NPS) has been evaluating the use of photovoltaic (PV) hybrid power systems, for many of its remote, off-grid areas. This paper reports the results of a detailed technical and economic evaluation for one such area: the Needles District of Canyonlands National Park. The study evaluates the presented power systems and five alternative power generation configurations, four of which utilise PV. Projections are provided for the generator run-time and fuel use associated with each configuration as well as all initial and future costs. Included in the study are specific recommendations for energy efficiency improvements at the site. Results show that the generation systems presently in use, two full-time diesel generators, has the lowest conventional 20-year life cycle costs (LCC) of the six systems evaluated. However, when emissions costs are included (per NPS guidelines), several of the PV hybrid alternatives attain a lower LCC than the diesel-only systems. General discussion of the effects of initial versus future costs of PV hybrids as they compare with engine generator system is presented. (Author)

  9. Geographic differences in time to culture conversion in liquid media: Tuberculosis Trials Consortium study 28. Culture conversion is delayed in Africa.

    Directory of Open Access Journals (Sweden)

    William R Mac Kenzie

    2011-04-01

    Full Text Available Tuberculosis Trials Consortium Study 28, was a double blind, randomized, placebo-controlled, phase 2 clinical trial examining smear positive pulmonary Mycobacterium tuberculosis. Over the course of intensive phase therapy, patients from African sites had substantially delayed and lower rates of culture conversion to negative in liquid media compared to non-African patients. We explored potential explanations of this finding.In TBTC Study 28, protocol-correct patients (n = 328 provided spot sputum specimens for M. tuberculosis culture in liquid media, at baseline and weeks 2, 4, 6 and 8 of study therapy. We compared sputum culture conversion for African and non-African patients stratified by four baseline measures of disease severity: AFB smear quantification, extent of disease on chest radiograph, cavity size and the number of days to detection of M. tuberculosis in liquid media using the Kaplan-Meier product-limit method. We evaluated specimen processing and culture procedures used at 29 study laboratories serving 27 sites.African TB patients had more extensive disease at enrollment than non-African patients. However, African patients with the least disease by the 4 measures of disease severity had conversion rates on liquid media that were substantially lower than conversion rates in non-African patients with the greatest extent of disease. HIV infection, smoking and diabetes did not explain delayed conversion in Africa. Some inter-site variation in laboratory processing and culture procedures within accepted practice for clinical diagnostic laboratories was found.Compared with patients from non-African sites, African patients being treated for TB had delayed sputum culture conversion and lower sputum conversion rates in liquid media that were not explained by baseline severity of disease, HIV status, age, smoking, diabetes or race. Further investigation is warranted into whether modest variation in laboratory processes substantially

  10. Neutronic study on conversion of SAFARI-1 to LEU silicide fuel

    International Nuclear Information System (INIS)

    Ball, G.; Pond, R.; Hanan, N.; Matos, J.

    1995-01-01

    This paper marks the initial study into the technical and economic feasibility of converting the SAFARI-1 reactor in South Africa to LEU silicide fuel. Several MTR assembly geometries and LEU uranium densities have been studied and compared with MEU and HEU fuels. Two factors of primary importance for conversion of SAFARI-1 to LEU fuel are the economy of the fuel cycle and the performance of the incore and excore irradiation positions

  11. Techno-economic study on conversion of SAFARI-1 to LEU silicide fuel

    International Nuclear Information System (INIS)

    Ball, G.; Malherbe, F.J.

    2004-01-01

    This paper marks the conclusion of the techno-economic study into the conversion of SAFARI-1 reactor in South Africa to LEU silicide fuel. Several different fuel types were studied and their characteristics compared to the current HEU fuel. The technical feasibility of operating SAFARI-1 with the different fuels as well as the overall economic impact of the fuels is discussed and conclusions drawn.(author)

  12. Alternation learning in pathological gamblers: an fMRI Study.

    Science.gov (United States)

    Dannon, Pinhas N; Kushnir, Tammar; Aizer, Anat; Gross-Isseroff, Ruth; Kotler, Moshe; Manor, David

    2011-03-01

    We have previously reported that pathological gamblers have impaired performance on the Stroop color word naming task, go-no-go task and speed accuracy tradeoff performance, tasks used to assess executive function and interference control. The aim of the present neuroimaging study was to explore the relationship between frontal cortex function and gambling severity in pathological gamblers. Functional MRI (fMRI) was used to estimate brain activity of ten male medication-free pathological gamblers during performance of an alternation learning task. Performance of this task has been shown to depend on the function of regions in the frontal cortex. The executive functions needed to perform the alternation learning task were expressed as brain activation in lateral and medial frontal as well as parietal and occipital regions. By correlating the level of local brain activation to task performance, parietal regions and lateral frontal and orbitofrontal regions were demonstrated. A higher score in SOGS was associated with intrusion on the task-specific activation in the left hemisphere, to some extant in parietal regions and even more pronouncedly in left frontal and orbitofrontal regions. Our preliminary data suggests that pathological gambling may be characterized by specific neuro-cognitive changes related to the frontal cortex.

  13. Digital radiography: study of an alternative technique to conventional radiography

    International Nuclear Information System (INIS)

    Banchet, J.; Tisseur, D.; Thomas, A.

    2009-01-01

    Digital radiography, already in use in many industrial applications, appears as a potential alternative technique to conventional radiography in the nuclear field (and more especially to the inspection of welded joints). The advantages of digital radiography are a reduced explosion risk (due to the use of lower energy and activity sources), a lower installation time, a reduced exclusion zone, and the absence of effluents. However, to the contrary of the US case, this technique may not be used in France as it is not referenced in the regulating codes (RCCM, etc.). Areva has launched a R and D study in order to characterize the equivalencies between digital and conventional radiography. First results of this study are given

  14. The radiation-induced topotactic conversion of di-para anthracene to anthracene: an electron microscopic study

    International Nuclear Information System (INIS)

    Parkinson, G.M.; Goringe, M.J.; Thomas, J.M.

    1977-01-01

    A study was made of single crystals of di-para anthracene, the product of photodimerisation of anthracene. This undergoes an electron-induced topotactic conversion to anthracene, and the study of this reaction using low temperature TEM enabled the identification of separate stages in the conversion and the elucidation of probable mechanistic routes. (author)

  15. An alternative approach for socio-hydrology: case study research

    Science.gov (United States)

    Mostert, Erik

    2018-01-01

    Currently the most popular approach in socio hydrology is to develop coupled human-water models. This article proposes an alternative approach, qualitative case study research, involving a systematic review of (1) the human activities affecting the hydrology in the case, (2) the main human actors, and (3) the main factors influencing the actors and their activities. Moreover, this article presents a case study of the Dommel Basin in Belgium and the Netherlands, and compares this with a coupled model of the Kissimmee Basin in Florida. In both basins a pendulum swing from water resources development and control to protection and restoration can be observed. The Dommel case study moreover points to the importance of institutional and financial arrangements, community values, and broader social, economic, and technical developments. These factors are missing from the Kissimmee model. Generally, case studies can result in a more complete understanding of individual cases than coupled models, and if the cases are selected carefully and compared with previous studies, it is possible to generalize on the basis of them. Case studies also offer more levers for management and facilitate interdisciplinary cooperation. Coupled models, on the other hand, can be used to generate possible explanations of past developments and quantitative scenarios for future developments. The article concludes that, given the limited attention they currently get and their potential benefits, case studies deserve more attention in socio-hydrology.

  16. Interactive programs with preschool children bring smiles and conversation to older adults: time-sampling study.

    Science.gov (United States)

    Morita, Kumiko; Kobayashi, Minako

    2013-10-18

    Keeping older adults healthy and active is an emerging challenge of an aging society. Despite the importance of personal relationships to their health and well-being, changes in family structure have resulted in a lower frequency of intergenerational interactions. Limited studies have been conducted to compare different interaction style of intergenerational interaction. The present study aimed to compare the changes in visual attention, facial expression, engagement/behaviour, and intergenerational conversation in older adults brought about by a performance-based intergenerational (IG) program and a social-oriented IG program to determine a desirable interaction style for older adults. The subjects of this study were 25 older adults who participated in intergenerational programs with preschool children aged 5 to 6 years at an adult day care centre in Tokyo. We used time sampling to perform a structured observation study. The 25 older participants of intergenerational programs were divided into two groups based on their interaction style: performance-based IG program (children sing songs and dance) and social-oriented IG program (older adults and children play games together). Based on the 5-minute video observation, we compared changes in visual attention, facial expression, engagement/behaviour, and intergenerational conversation between the performance-based and social-oriented IG programs. Constructive behaviour and intergenerational conversation were significantly higher in the social-oriented IG programming group than the performance-based IG programming group (pprogramming group than the performance-based IG programming (pprogramming group than the social-oriented IG programming group (pprograms with preschool children brought smiles and conversation to older adults. The social-oriented IG program allowed older adults to play more roles than the performance-based IG program. The intergenerational programs provide opportunities to fulfil basic human needs and

  17. Thyroid Cancer Treatment Choice: A pilot study of a tool to facilitate conversations with patients with papillary microcarcinomas considering treatment options.

    Science.gov (United States)

    Brito, Juan P; Moon, Jae Hoon; Zeuren, Rebecca; Kong, Sung Hye; Kim, Yeo Koon; Iñiguez-Ariza, Nicole M; Choi, June Young; Lee, Kyu Eun; Kim, Ji-Hoon; Hargraves, Ian; Bernet, Victor; Montori, Victor; Park, Young Joo; Tuttle, R Michael

    2018-06-15

    The 2015 American Thyroid Association guidelines recognize active surveillance as an alternative to immediate surgery in patients with papillary microcarcinomas (PMCs). As a way to incorporate active surveillance as one of the management options for patients with PMCs, we describe the development and initial testing of a tool to support conversations between clinicians and patients with PMCs considering treatment options. Thyroid Cancer Treatment Choice was developed using an iterative process based on the principles of interaction, design and participatory action research. To evaluate the impact of the tool on treatment choice, a prospective study was conducted in two thyroid cancer clinics in Seongnam-si and Seoul, South Korea: both clinics had the expertise to offer active surveillance as well as immediate surgery. One clinic was trained in the use of the conversation aid, while the other clinic continued to care for patients without access to the conversation aid. Between May 2016 and April 2017, 278 patients mostly women (n=220, 79%) were included in the study; 152 (53%) received care at the clinic using the conversation aid. Age, gender, and mean tumor size [6.6 mm (SD 1.6) and 6.5 mm (SD 1.9)] distributions were similar across clinics. Overall, 233 (84%) patients opted for active surveillance and 53 (16%) for thyroid surgery. Patients in the conversation aid group were more likely to choose active surveillance than the patients seen in the usual care clinic [relative risk (RR) = 1.16; 95% confidence interval (CI), 1.04 - 1.29]. Of all patients opting for active surveillance, more patients in the conversation aid group had thyroid cancer nodules > 5 mm than in the usual care group (81% vs. 67% P = 0.013). Thyroid Cancer Treatment Choice is an evidence-based tool that supports the presentation of treatment options for PMCs. Pilot testing suggests that this conversation tool increases acceptance of active surveillance, suggesting that this option is an

  18. Physico-chemical and thermochemical studies of the hydrolytic conversion of amorphous tricalcium phosphate into apatite

    International Nuclear Information System (INIS)

    Somrani, Saida; Banu, Mihai; Jemal, Mohamed; Rey, Christian

    2005-01-01

    The conversion of amorphous tricalcium phosphate with different hydration ratio into apatite in water at 25 deg. C has been studied by microcalorimetry and several physical-chemical methods. The hydrolytic transformation was dominated by two strong exothermic events. A fast, relatively weak, wetting process and a very slow but strong heat release assigned to a slow internal rehydration and the crystallization of the amorphous phase into an apatite. The exothermic phenomenon related to the rehydration exceeded the crystalline transformation enthalpy. Rehydration occurred before the conversion of the amorphous phase into apatite and determined the advancement of the hydrolytic reaction. The apatitic phases formed evolved slightly with time after their formation. The crystallinity increased whereas the amount of HPO 4 2- ion decreased. These data allow a better understanding of the behavior of biomaterials involving amorphous phases such as hydroxyapatite plasma-sprayed coatings

  19. Study of the Energy Conversion Process in the Electro-Hydrostatic Drive of a Vehicle

    Directory of Open Access Journals (Sweden)

    Wiesław Grzesikiewicz

    2018-02-01

    Full Text Available In the paper, we describe a study of an electro-hydrostatic hybrid drive of a utility van intended for city traffic. In this hybrid drive, the electric drive is periodically accompanied by hydrostatic drive, especially during acceleration and regenerative braking of the vehicle. We present a mathematical model of the hybrid drive as a set of dynamics and regulation equations of the van traveling at a given speed. On this basis, we construct a computer program which we use to simulate the processes of energy conversion in the electro-hydrostatic drive. The main goal of the numerical simulation is to assess the possibility of reducing energy intensity of the electric drive through such a support of the hydrostatic drive. The obtained results indicate that it is possible to reduce the load on elements of the electric system and, therefore, improve energy conversion.

  20. A Study on the Guided Wave Mode Conversion using Self-calibrating Technique

    International Nuclear Information System (INIS)

    Park, Jung Chul; Cho, Youn Ho

    2000-01-01

    The guided wave mode conversion phenomena were investigated for the NDE of a plate-like structure with thickness variation. The ratios of reflection and transmission (R/T) were measured via the self-calibrating procedure which allows us to obtain experimental guided wave data in a more reliable way regardless of the coupling uncertainty between transducer and specimen. The results on R/T could be used to determine the thickness reduction of the structure. It was shown that not only the incident modes but also the converted ones need to be considered in the self-calibrating guided wave inspection to extract a reasonable correlation between experimental data and the thickness variation. Through this study, the potential of guided wave inspection as a quantitative NDE technique was explored based on the combined concept of self-calibration and multi-mode conversion in guided wave scattering problems

  1. An Experimental Study on Energy Conversion Process of an in-Space CW Laser Thruster

    International Nuclear Information System (INIS)

    Uehara, Susumu; Inoue, Takayoshi; Komurasaki, Kimiya; Arakawa, Yoshihiro

    2005-01-01

    CW laser propulsion has been investigated to develop a prospective propulsion system that may be used in space. OTV (Orbit Transfer Vehicle) is placed as one of the most effective applications of the propulsion system. In this study, the energy partitioning of incident laser energy was investigated over the wide range of velocity of the flow field in low pressure. Flow velocity is thought to have significant effects on energy conversion process because the distribution of temperature and the position of a laser sustained plasma in the focusing laser beam should be determined so that flow velocity and propagation velocity of optical discharge balance out. It was found that the higher energy conversion efficiency can be achieved by lowering the pressure and increasing the velocity of the flow field

  2. The study, design and simulation of a free piston Stirling engine linear alternatorThe study, design and simulation of a free piston Stirling engine linear alternator

    Directory of Open Access Journals (Sweden)

    Teodora Susana Oros

    2014-12-01

    Full Text Available This paper presents a study, design and simulation of a Free Piston Stirling Engine Linear Alternator. There are presented the main steps of the magnetic and electric calculations for a permanent magnet linear alternator of fixed coil and moving magnets type. Finally, a detailed thermal, mechanical and electrical model for a Stirling engine linear alternator have been made in SIMULINK simulation program. The linear alternator simulation model uses a controllable DC voltage which simulates the linear alternator combined with a rectifier, a variable load and a DC-DC converter, which compensates for the variable nature of Stirling engine operation, and ensures a constant voltage output regardless of the load.

  3. Applicability of dose conversion coefficients of ICRP 74 to Asian adult males: Monte Carlo simulation study

    International Nuclear Information System (INIS)

    Lee, Choonsik; Lee, Choonik; Lee, Jai-Ki

    2007-01-01

    International Commission on Radiological Protection (ICRP) reported comprehensive dose conversion coefficients for adult population, which is exposed to external photon sources in the Publication 74. However, those quantities were calculated from so-called stylized (or mathematical) phantoms composed of simplified mathematical surface equations so that the discrepancy between the phantoms and real human anatomy has been investigated by several authors using Caucasian-based voxel phantoms. To address anatomical and racial limitations of the stylized phantoms, several Asian-based voxel phantoms have been developed by Korean and Japanese investigators, independently. In the current study, photon dose conversion coefficients of ICRP 74 were compared with those from a total of five Asian-based male voxel phantoms, whose body dimensions were almost identical. Those of representative radio-sensitive organs (testes, red bone marrow, colon, lungs, and stomach), and effective dose conversion coefficients were obtained for comparison. Even though organ doses for testes, colon and lungs, and effective doses from ICRP 74 agreed well with those from Asian voxel phantoms within 10%, absorbed doses for red bone marrow and stomach showed significant discrepancies up to 30% which was mainly attributed to difference of phantom description between stylized and voxel phantoms. This study showed that the ICRP 74 dosimetry data, which have been reported to be unrealistic compared to those from Caucasian-based voxel phantoms, are also not appropriate for Asian population

  4. Techno-economic study of different alternatives for biodiesel production

    International Nuclear Information System (INIS)

    Marchetti, J.M.; Miguel, V.U.; Errazu, A.F.

    2008-01-01

    Biodiesel has become an attractive diesel fuel substitute due to its environmental benefits since it can be made from renewable resource. However, the high costs surrounding biodiesel production remains the main problem in making it competitive in the fuel market either as a blend or as a neat fuel. More than 80% of the production cost is associated with the feedstock itself and consequently, efforts are focused on developing technologies capable of using lower-cost feedstocks, such as recycled cooking oils and wastes from animal or vegetable oil processing operations. The main issue with spent oils is the high level of free fatty acids found in the recycled materials. The conventional technology employs sodium methoxide as a homogeneous base catalyst for the transesterification reaction and illustrates the drawbacks in working with feedstocks that contain high levels of free fatty acids. On the other hand, homogeneous acidic catalysts are being used for exactly such feedstocks. Both acid and basic homogeneous catalyzed processes require downstream purification equipment to neutralize the catalyst and to purify the biodiesel as well as the glycerol. Recent studies have been conducted to employ heterogeneous catalysts, such acidic or basic solid resins, or immobilized lipases. These catalysts will allow the use of different feedstocks that will permit operation at lower investment costs and will require less downstream process equipment. A conceptual design of these alternative production plants has been done with a techno-economic analysis in order to compare these alternatives. A process simulator was employed to carry out the conceptual design and simulation of each technology. Using these models it was possible to analyze different scenarios and to evaluate productivity, raw material consumption, economic competitiveness, and environmental impacts of each process. (author)

  5. Integrating alternative providers into managed care: a case study.

    Science.gov (United States)

    Broida, M

    1997-09-01

    Alternative medical techniques have become extremely popular, particularly in the western United States. Washington State recently enacted a law requiring certain health plans to include alternative providers on their physician panels. The author describes the efforts of one MCO to comply.

  6. Alternative Tobacco Product Use and Smoking Cessation: A National Study

    Science.gov (United States)

    Popova, Lucy

    2013-01-01

    Objectives. We investigated the frequency of alternative tobacco product use (loose leaf, moist snuff, snus, dissolvables, electronic cigarettes [e-cigarettes]) among smokers and the association with quit attempts and intentions. Methods. A nationally representative probability-based cross-sectional survey of 1836 current or recently former adult smokers was completed in November 2011. Multivariate logistic regressions evaluated associations between alternative tobacco product use and smoking cessation behaviors. Results. Of the smokers, 38% had tried an alternative tobacco product, most frequently e-cigarettes. Alternative tobacco product use was associated with having made a quit attempt, and those intending to quit were significantly more likely to have tried and to currently use the products than were smokers with no intentions to quit. Use was not associated with successful quit attempts. Interest in future use of alternative tobacco products was low, except for e-cigarettes. Conclusions. Alternative tobacco products are attractive to smokers who want to quit smoking, but these data did not indicate that alternative tobacco products promote cessation. Unsubstantiated overt and implied claims that alternative tobacco products aid smoking cessation should be prohibited. PMID:23488521

  7. Confidential conversations between supervisor and employee as a means for improving leadership: a quasi-experimental study in hospital wards.

    Science.gov (United States)

    Kivimäki, M

    1996-11-01

    Although yearly confidential conversations between a supervisor and an employee have been recommended as a means for improving leadership, evidence on the actual effects of these conversations has been lacking. The present study therefore investigated whether confidential conversations improve perceptions of goal clarity, sufficiency of feedback and innovativeness, and elicit satisfaction with the supervisor's leadership style within the hospital setting. Nine wards were divided into one experimental group (3 wards) and two control groups (3 + 3 wards). A questionnaire on goal clarity, feedback, innovativeness and satisfaction was administered twice to every group (1st measurement: r = 186, 2nd measurement: n = 163). The experimental group began confidential conversations after the first measurement, control group 1 entered into conversations during both measurements, and control group 2 did not enter into conversations at the time of either measurement. Confidential conversations improved perceived feedback. In both measurements, the sufficiency of feedback was reported to be significantly better in the groups having conversations than in the other groups. In addition, there was a significant positive change in the perceived sufficiency of feedback in the experimental group but not in the other groups. Confidential conversations did not affect the perceptions of goal clarity and innovativeness or elicit satisfaction with the supervisor's management style.

  8. Cogeneration Technology Alternatives Study (CTAS). Volume 3: Industrial processes

    Science.gov (United States)

    Palmer, W. B.; Gerlaugh, H. E.; Priestley, R. R.

    1980-01-01

    Cogenerating electric power and process heat in single energy conversion systems rather than separately in utility plants and in process boilers is examined in terms of cost savings. The use of various advanced energy conversion systems are examined and compared with each other and with current technology systems for their savings in fuel energy, costs, and emissions in individual plants and on a national level. About fifty industrial processes from the target energy consuming sectors were used as a basis for matching a similar number of energy conversion systems that are considered as candidate which can be made available by the 1985 to 2000 time period. The sectors considered included food, textiles, lumber, paper, chemicals, petroleum, glass, and primary metals. The energy conversion systems included steam and gas turbines, diesels, thermionics, stirling, closed cycle and steam injected gas turbines, and fuel cells. Fuels considered were coal, both coal and petroleum based residual and distillate liquid fuels, and low Btu gas obtained through the on site gasification of coal. An attempt was made to use consistent assumptions and a consistent set of ground rules specified by NASA for determining performance and cost. Data and narrative descriptions of the industrial processes are given.

  9. Conversion of laparoscopic surgery for perforated peptic ulcer: a single-center study.

    Science.gov (United States)

    Zimmermann, Markus; Hoffmann, Martin; Laubert, Tilman; Jung, Carlo; Bruch, Hans-Peter; Schloericke, Erik

    2015-11-01

    A perforated peptic ulcer can be managed laparoscopically in selected patients. The purpose of this study was to evaluate whether conversion of emergency laparoscopy is inferior to primary median laparotomy in terms of postoperative morbidity and mortality. We analyzed patients who underwent laparoscopic or open surgery for a perforated peptic ulcer at the Department of Surgery, University of Schleswig-Holstein, Campus Luebeck between January, 1996 and December, 2010. Perforations were graded according to the Boey classification, a preoperative risk-scoring system. Conversion to laparotomy was necessary in 20 of the 45 patients who underwent laparoscopic surgery (CG); therefore, laparoscopic operations were completed in 25 patients (LG). The third patient cohort comprised 139 patients who underwent primary laparotomy (OG). Overall minor morbidity was significantly lower (p = 0.048) in the LG patients than in the OG patients, whereas no significant differences were found in major morbidity and mortality, particularly between the OG and CG. Patients' suitability for laparoscopic management should be decided on according to Boey's clinical scoring system. Our findings demonstrated that conversion from laparoscopy to laparotomy was not associated with elevated postoperative morbidity or mortality versus initial laparotomy. Therefore, emergency operations may be commenced laparoscopically in selected patients, especially considering the postoperative advantages of this approach.

  10. Physics and safety studies of a low conversion ratio sodium cooled fast reactor

    International Nuclear Information System (INIS)

    Cahalan, J. E.; Smith, M. A.; Hill, R. N.; Dunn, F. E.

    2004-01-01

    This paper explores the feasibility of a compact fast burner reactor that can achieve a low transuranic conversion ratio. The major design option considered is the reduction of fissile breeding by the removal of fertile material from the fast reactor system. Reductions in the fuel pin diameter and thus fuel loading were employed to remove fertile material. Reactor performance parameters and reactivity coefficients were evaluated for a compact core design with a targeted conversion ratio of 0.25. To assess the safety implications, a detailed transient analysis model was employed using the SAS4A/SASSYS-1 computer code. A series of calculations was performed to assess the behavior of the reactor and plant in an unprotected loss-of-flow accident (ULOF). A parametric study was also carried out using increasingly conservative modeling assumptions. The computational results show that for nominal, best-estimate analysis assumptions and input data, the low conversion ratio reactor design responds to the ULOF with a very high level of self-protection. Both short-term and long-term quasi-equilibrium reactor conditions predicted in the analysis indicate very large margins of safety. (authors)

  11. Cardiac and vascular structure and function parameters do not improve with alternate nightly home hemodialysis: An interventional cohort study

    Directory of Open Access Journals (Sweden)

    Johnson David W

    2011-10-01

    Full Text Available Abstract Background Nightly extended hours hemodialysis may improve left ventricular hypertrophy and function and endothelial function but presents problems of sustainability and increased cost. The effect of alternate nightly home hemodialysis (NHD on cardiovascular structure and function is not known. Methods Sixty-three patients on standard hemodialysis (SHD: 3.5-6 hours/session, 3-5 sessions weekly converted to NHD (6-10 hours/session overnight for 3-5 sessions weekly. 2Dimensional transthoracic echocardiography and ultrasound measures of brachial artery reactivity (BAR, carotid intima-media thickness (CIMT, total arterial compliance (TAC and augmentation index (AIX were performed post dialysis at baseline and 18-24 months following conversion to NHD. In 37 patients, indices of oxidative stress: plasma malonyldialdehyde (MDA and anti-oxidant enzymes: catalase (CAT, glutathione peroxidase (GPX and superoxide dismutase (SOD activity and total antioxidant status (TAS were measured at baseline, 3 and 6 months. Results Left ventricular mass index (LVMI remained stable. Despite significant derangement at baseline, there were no changes in diastolic function measures, CIMT, BAR and TAC. AIX increased. Conversion to NHD improved bone mineral metabolism parameters and blood pressure control. Interdialytic weight gains increased. No definite improvements in measures of oxidative stress were demonstrated. Conclusions Despite improvement in uremic toxin levels and some cardiovascular risk factors, conversion to an alternate nightly NHD regimen did not improve cardiovascular structure and function. Continuing suboptimal control of uremic toxins and interdialytic weight gains may be a possible explanation. This study adds to the increasing uncertainty about the nature of improvement in cardiovascular parameters with conversion to intensive hemodialysis regimens. Future randomized controlled trials will be important to determine whether increases in

  12. Adhesion and corrosion studies of a lithium based conversion coating film on the 2024 aluminum alloy

    International Nuclear Information System (INIS)

    Castro, M.R.S.; Nogueira, J.C.; Thim, G.P.; Oliveira, M.A.S.

    2004-01-01

    AA2024-T3-aluminum alloy surfaces were coated using non-chromate and chromate conversion coatings. All coatings were painted with the 10P4-2-primer epoxy resin. Independent on the film formation process, films passed on the substrate/conversion coating wet tape adhesion test. However, only the chromate conversion coating passed on the conversion coating/primer epoxy resin adhesion test. Electrochemical corrosion measurements showed that non-chromate conversion coated surfaces present lower corrosion current density, bigger polarization resistance and less negative corrosion potential than chromate conversion coated surfaces

  13. Irreversible Conversion of a Water-Ethanol Solution into an Organized Two-Dimensional Network of Alternating Supramolecular Units in a Hydrophobic Zeolite under Pressure.

    Science.gov (United States)

    Arletti, Rossella; Fois, Ettore; Gigli, Lara; Vezzalini, Giovanna; Quartieri, Simona; Tabacchi, Gloria

    2017-02-13

    Turning disorder into organization is a key issue in science. By making use of X-ray powder diffraction and modeling studies, we show herein that high pressures in combination with the shape and space constraints of the hydrophobic all-silica zeolite ferrierite separate an ethanol-water liquid mixture into ethanol dimer wires and water tetramer squares. The confined supramolecular blocks alternate in a binary two-dimensional (2D) architecture that remains stable upon complete pressure release. These results support the combined use of high pressures and porous networks as a viable strategy for driving the organization of molecules or nano-objects towards complex, pre-defined patterns relevant for the realization of novel functional nanocomposites. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Study of an alternative system for manganese bath efficiency determination

    International Nuclear Information System (INIS)

    Leite, Sandro Passos

    2010-01-01

    An alternative irradiation system, using radioisotope neutron sources and a small MnSO 4 solution volume, was proposed m this work to determine the Manganese Bath System (MBS) efficiency. The irradiation system was characterized through simulations with the MCNP radiation transport code from the modeling of 252 Cf(f,n) and 238 PuBe(alpha,n) neutron sources in several MnSO 4 solution volumes and different neutron reflector medium for this solution. The parameter calculated in the simulations was the manganese neutron specific capture (MNSC), which is related to the MnSO 4 solution specific activity. From the proposed systems for 252 Cf (f, n) and 238 PuBe (alpha,n) the NSCM was increased hundred times, in relation with that achieved in the LN/LNMRI/IRD MBS system simulation when irradiated by each these neutron sources. During study for irradiation system characterization its concept was verified using a assemble of test irradiation (ATI), which were spherical glass cavities, with few centimeter in radius, filled with MnSO 4 solution, with and without presence of a neutron reflector medium. These TIA were used in four efficiency measurements and the average value was obtained. (author)

  15. Jatropha waste meal as an alternative energy source via pressurized pyrolysis: A study on temperature effects

    International Nuclear Information System (INIS)

    Kongkasawan, Jinjuta; Nam, Hyungseok; Capareda, Sergio C.

    2016-01-01

    As an alternative energy source, Jatropha is a promising biomass resource due to its high content of oil contained in the seed. However, after the oil extraction process, more than 50% of initial weight remained as residue. This Jatropha de-oiled cake was considered a valuable feedstock for thermochemical conversion process due to its high volatile matter (73%) and energy content (20.5 MJ/kg). Pyrolysis turned biomass into solid product of biochar, liquid product (bio-oil and aqueous phase), and pyrolysis gas. The effects of pyrolysis temperature under the pressure of 0.69 MPa on the product yields and characteristics were investigated using a bench-scale batch reactor. The gross calorific value of pyrolytic oil was measured to be 35 MJ/kg with high carbon content (71%) and low oxygen content (10%). Phenols and hydrocarbons were the main compounds present in the pyrolytic oil. The heating value of the biochar was also high (28 MJ/kg), which was comparable to the fuel coke. More combustible gases were released at high pyrolysis temperature with methane as a main constituent. Pyrolysis temperature of 500 °C, was determined to be an optimum condition for the mass and energy conversions with 89% of the mass and 77% of the energy recovered. - Highlights: • Pressurized pyrolysis of Jatropha wastes at different temperatures was studied. • Full analysis of biochar, bio-oil and pyro gas at different temperatures were done. • Highest aromatics (32%) and HHV (35 MJ/kg) found in bio-oil at 500 °C. • Large amount of paraffins (C 13 –C 16 range) was found in bio-oil.

  16. Development of a mini-orange spectrometer for conversion electron study

    International Nuclear Information System (INIS)

    Mishra, N.R.; Chakravarty, V.; Chintalapudi, S.N.; Ghugre, S.S.; Sastry, D.L.

    1996-01-01

    Conversion electrons provide with an unique tool to have an unambiguous multipolarity assignment for the observed gamma transitions. The fabrication of an electron spectrometer to detect these conversion electrons is a non-trivial task

  17. Attachment behavior and mother-child conversations as predictors of attachment representations in middle childhood: a longitudinal study.

    Science.gov (United States)

    Dubois-Comtois, Karine; Cyr, Chantal; Moss, Ellen

    2011-07-01

    This study examines longitudinal links between mother-child conversations and attachment patterns in early childhood and later attachment representations. It also tests the role of conversations as mediators in the association between behavioral security and attachment representations. Mother-child conversations (snack-time) and attachment behaviors (Separation-Reunion procedure) were assessed for 83 5.5-year-olds while attachment representations (attachment narratives) were measured at 8.5 years of age. Results showed correspondence between attachment behaviors and representations for secure-confident, ambivalent-preoccupied, and disorganized/controlling-frightened groups. Affective quality of mother-child conversations predicted both child attachment behaviors and representations. Secure and confident children showed greater integration of affective information, ambivalent and preoccupied children more affect exaggeration, and disorganized/controlling and frightened children more chaotic conversations. Avoidant children tended to show more affect minimization in conversations. Finally, mother-child conversations centered on the sharing of emotions and thoughts mediated the relation between behavioral and representational attachment security, which underscores the importance of mother-child conversations in the development of attachment representations in childhood.

  18. Oxidising alternative species to chromium VI in zinc-galvanised steel surface treatment. Part 2. An electrochemical study

    International Nuclear Information System (INIS)

    Almeida, E.; Fedrizzi, L.; Diamantinio, T.C.

    1998-01-01

    In the first part of this work, the authors present the main results and conclusions of a morphological and chemical study carried out on zinc conversion layers (ZCLs) obtained with oxidising alternative passivation baths, that includes molybdates, permanganates, van[ates and tungstates. A good chromate-based bath was used as reference. In this second part of the work, the authors present the main results obtained on selected zinc conversion layers (ZCLs), using a.c. electrochemical impedance spectroscopy (EIS). The results obtained were correlated with the morphological and chemical data obtained with the same ZCLs in the first part of this work. Finally, it is concluded that the alternative ZCLs studied, does not seem to be as efficient as that obtained with a chromate-based passivation bath used as reference. It is believed that a better understanding of the mechanisms involved in the ZCL's formation, can be useful for studying, in the very near future, possible synergetic effects between molybdates and other chemical species. (orig.)

  19. Study of energy conversion and partitioning in the magnetic reconnection layer of a laboratory plasma

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, Masaaki; Yoo, Jongsoo; Jara-Almonte, Jonathan; Ji, Hantao; Kulsrud, Russell M.; Myers, Clayton E. [Princeton Plasma Physics Laboratory, Princeton University, Princeton, New Jersey 08543 (United States); Daughton, William [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States)

    2015-05-15

    While the most important feature of magnetic reconnection is that it energizes plasma particles by converting magnetic energy to particle energy, the exact mechanisms by which this happens are yet to be determined despite a long history of reconnection research. Recently, we have reported our results on the energy conversion and partitioning in a laboratory reconnection layer in a short communication [Yamada et al., Nat. Commun. 5, 4474 (2014)]. The present paper is a detailed elaboration of this report together with an additional dataset with different boundary sizes. Our experimental study of the reconnection layer is carried out in the two-fluid physics regime where ions and electrons move quite differently. We have observed that the conversion of magnetic energy occurs across a region significantly larger than the narrow electron diffusion region. A saddle shaped electrostatic potential profile exists in the reconnection plane, and ions are accelerated by the resulting electric field at the separatrices. These accelerated ions are then thermalized by re-magnetization in the downstream region. A quantitative inventory of the converted energy is presented in a reconnection layer with a well-defined, variable boundary. We have also carried out a systematic study of the effects of boundary conditions on the energy inventory. This study concludes that about 50% of the inflowing magnetic energy is converted to particle energy, 2/3 of which is ultimately transferred to ions and 1/3 to electrons. Assisted by another set of magnetic reconnection experiment data and numerical simulations with different sizes of monitoring box, it is also observed that the observed features of energy conversion and partitioning do not depend on the size of monitoring boundary across the range of sizes tested from 1.5 to 4 ion skin depths.

  20. Achieving consensus on the definition of conversion to laparotomy: a Delphi study among general surgeons, gynecologists, and urologists.

    Science.gov (United States)

    Blikkendaal, Mathijs D; Twijnstra, Andries R H; Stiggelbout, Anne M; Beerlage, Harrie P; Bemelman, Willem A; Jansen, Frank Willem

    2013-12-01

    In laparoscopic surgery, conversion to laparotomy is associated with worse clinical outcomes, especially if the conversion is due to a complication. Although apparently important, no commonly used definition of conversion exists. The aim of this study was to achieve multidisciplinary consensus on a uniform definition of conversion. On the basis of definitions currently used in the literature, a web-based Delphi consensus study was conducted among members of all four Dutch endoscopic societies. The rate of agreement (RoA) was calculated; a RoA of >70% suggested consensus. The survey was completed by 268 respondents in the first Delphi round (response rate, 45.6%); 43% were general surgeons, 49% gynecologists, and 8% urologists. Average ± standard deviation laparoscopic experience was 12.5 ± 7.2 years. On the basis of the results of round 1, a consensus definition was compiled. Conversion to laparotomy is an intraoperative switch from a laparoscopic to an open abdominal approach that meets the criteria of one of the two subtypes: strategic conversion, a standard laparotomy that is made directly after the assessment of the feasibility of completing the procedure laparoscopically and because of anticipated operative difficulty or logistic considerations; and reactive conversion, the need for a laparotomy because of a complication or (extension of an incision) because of (anticipated) operative difficulty after a considerable amount of dissection (i.e., >15 min in time). A laparotomy after a diagnostic laparoscopy (i.e., to assess the curability of the disease) should not be considered a conversion. In the second Delphi round, a RoA of 90% was achieved with this definition. After two Delphi rounds, consensus on a uniform multidisciplinary definition of conversion was achieved within a representative group of general surgeons, gynecologists, and urologists. An unambiguous interpretation will result in a more reliable clinical registration of conversion and scientific

  1. A comparative study between three sensorless control strategies for PMSG in wind energy conversion system

    Energy Technology Data Exchange (ETDEWEB)

    Brahmi, Jemaa; Krichen, Lotfi; Ouali, Abderrazak [Advanced Control and Energy Management Research Unit ENIS, Department of Electrical Engineering, University of Sfax, 3038 Sfax (Tunisia)

    2009-09-15

    This paper presents a comparative study of sliding mode, artificial neural network and model reference adaptive speed observers for a speed sensorless permanent magnet synchronous generator (PMSG) in wind energy conversion system (WECS). Wind velocity and position sensorless operating methods for wind generation system using observer are proposed only by measuring phase voltages and currents. Maximum wind energy extraction is achieved by running the wind turbine generator in variable-speed mode. In addition the three speed observers are compared to verify the robustness against parameter variations. (author)

  2. Neutronic feasibility studies for LEU conversion of the HFR Petten reactor

    International Nuclear Information System (INIS)

    Hanan, N.A.; Deen, J.R.; Matos, J.E.; Hendriks, J.A.; Thijssen, P.J.M.; Wijtsma, F.J.

    2000-01-01

    Design and safety analyses to determine an optimum LEU fuel assembly design using U 3 Si 2 -Al fuel with up to 4.8 g/cm 3 for conversion of the HFR Petten reactor were performed by the RERTR program in cooperation with the Joint Research Centre and NRG. Credibility of the calculational methods and models were established by comparing calculations with recent measurements by NRG for a core configuration set up for this purpose. This model and methodology were then used to study various LEU fissile loading and burnable poison options that would satisfy specific design criteria. (author)

  3. WRAP Module 1 sampling strategy and waste characterization alternatives study

    Energy Technology Data Exchange (ETDEWEB)

    Bergeson, C.L.

    1994-09-30

    The Waste Receiving and Processing Module 1 Facility is designed to examine, process, certify, and ship drums and boxes of solid wastes that have a surface dose equivalent of less than 200 mrem/h. These wastes will include low-level and transuranic wastes that are retrievably stored in the 200 Area burial grounds and facilities in addition to newly generated wastes. Certification of retrievably stored wastes processing in WRAP 1 is required to meet the waste acceptance criteria for onsite treatment and disposal of low-level waste and mixed low-level waste and the Waste Isolation Pilot Plant Waste Acceptance Criteria for the disposal of TRU waste. In addition, these wastes will need to be certified for packaging in TRUPACT-II shipping containers. Characterization of the retrievably stored waste is needed to support the certification process. Characterization data will be obtained from historical records, process knowledge, nondestructive examination nondestructive assay, visual inspection of the waste, head-gas sampling, and analysis of samples taken from the waste containers. Sample characterization refers to the method or methods that are used to test waste samples for specific analytes. The focus of this study is the sample characterization needed to accurately identify the hazardous and radioactive constituents present in the retrieved wastes that will be processed in WRAP 1. In addition, some sampling and characterization will be required to support NDA calculations and to provide an over-check for the characterization of newly generated wastes. This study results in the baseline definition of WRAP 1 sampling and analysis requirements and identifies alternative methods to meet these requirements in an efficient and economical manner.

  4. WRAP Module 1 sampling strategy and waste characterization alternatives study

    International Nuclear Information System (INIS)

    Bergeson, C.L.

    1994-01-01

    The Waste Receiving and Processing Module 1 Facility is designed to examine, process, certify, and ship drums and boxes of solid wastes that have a surface dose equivalent of less than 200 mrem/h. These wastes will include low-level and transuranic wastes that are retrievably stored in the 200 Area burial grounds and facilities in addition to newly generated wastes. Certification of retrievably stored wastes processing in WRAP 1 is required to meet the waste acceptance criteria for onsite treatment and disposal of low-level waste and mixed low-level waste and the Waste Isolation Pilot Plant Waste Acceptance Criteria for the disposal of TRU waste. In addition, these wastes will need to be certified for packaging in TRUPACT-II shipping containers. Characterization of the retrievably stored waste is needed to support the certification process. Characterization data will be obtained from historical records, process knowledge, nondestructive examination nondestructive assay, visual inspection of the waste, head-gas sampling, and analysis of samples taken from the waste containers. Sample characterization refers to the method or methods that are used to test waste samples for specific analytes. The focus of this study is the sample characterization needed to accurately identify the hazardous and radioactive constituents present in the retrieved wastes that will be processed in WRAP 1. In addition, some sampling and characterization will be required to support NDA calculations and to provide an over-check for the characterization of newly generated wastes. This study results in the baseline definition of WRAP 1 sampling and analysis requirements and identifies alternative methods to meet these requirements in an efficient and economical manner

  5. A study on the alternative option for nuclear policy

    Energy Technology Data Exchange (ETDEWEB)

    Choi, J. W.; Choi, H. J.; Lee, J. Y.; Cho, D. K.; Jeon, K. S.; Park, S. W.; Hahn, D. H.; Yoon, J. S.; Lee, K. S. [KAERI, Daejeon (Korea, Republic of)

    2008-02-15

    Since a decision-making by intuitive judgement under uncertain future conditions can not select an optimum alternative, reaching an agreement for alternatives between experts requires a development of several scientific opinion collection methodologies and performing these methodologies. Therefore, opinion collection for all points related to the nuclear energy, public hearing induction related researches and the acts, procedure, etc. performed in developed countries such as U.S, U.K, France, etc. are reviewed and analyzed in this research. And after the analysis of domestic spent nuclear fuel management plan, Task Force Team composed of experts in several related areas is organized to suggest strategies and directions which are necessary for making a national policy. Beside, Task Force Team selects an optimum technical alternative by the analysis and comparison in depth between these technical alternatives to establish the policy direction. They also established the procedures such as opinion collecting, etc. through policy conference and forum and suggested the technical data related nuclear policy which supports the nuclear policy conference. Results from this research are expected to decrease the trial and error that has been occurred in the present policy-making procedure such as radioactive waste repository related procedure and contribute for socio-cultural stability. Moreover, opinion collection plan for developing a nuclear policy alternative is expected to contribute for making a nuclear policy in the nuclear policy conference so that the nuclear technology will be enhanced more.

  6. A study on the alternative option for nuclear policy

    International Nuclear Information System (INIS)

    Choi, J. W.; Choi, H. J.; Lee, J. Y.; Cho, D. K.; Jeon, K. S.; Park, S. W.; Hahn, D. H.; Yoon, J. S.; Lee, K. S.

    2008-02-01

    Since a decision-making by intuitive judgement under uncertain future conditions can not select an optimum alternative, reaching an agreement for alternatives between experts requires a development of several scientific opinion collection methodologies and performing these methodologies. Therefore, opinion collection for all points related to the nuclear energy, public hearing induction related researches and the acts, procedure, etc. performed in developed countries such as U.S, U.K, France, etc. are reviewed and analyzed in this research. And after the analysis of domestic spent nuclear fuel management plan, Task Force Team composed of experts in several related areas is organized to suggest strategies and directions which are necessary for making a national policy. Beside, Task Force Team selects an optimum technical alternative by the analysis and comparison in depth between these technical alternatives to establish the policy direction. They also established the procedures such as opinion collecting, etc. through policy conference and forum and suggested the technical data related nuclear policy which supports the nuclear policy conference. Results from this research are expected to decrease the trial and error that has been occurred in the present policy-making procedure such as radioactive waste repository related procedure and contribute for socio-cultural stability. Moreover, opinion collection plan for developing a nuclear policy alternative is expected to contribute for making a nuclear policy in the nuclear policy conference so that the nuclear technology will be enhanced more

  7. Technology Overview Using Case Studies of Alternative Landfill Technologies and Associated Regulatory Topics

    National Research Council Canada - National Science Library

    2003-01-01

    ... alternative landfill cover projects. The purpose of the case studies is to present examples of the flexibility used in the regulatory framework for approving alternative landfill cover designs, current research information about the use...

  8. A feasibility study of conceptual design for international clean energy network using hydrogen conversion technology

    International Nuclear Information System (INIS)

    Sato, Takashi; Hamada, Akiyoshi; Kitamura, Kazuhiro

    1998-01-01

    Clean energy is more and more required worldwide in proportion to actualization of global environmental issues including global warming. Therefore, it is an urgent task to realize promotion of worldwide introduction of clean energy which exists abundantly and is widely distributed in the world, such as hydropower and solar energy, while reducing the dependence on fossil fuel. However, since the renewable energy, differing from so called fossil fuel, is impossible to transport for long distance and store as it is, its utilization is subject to be limited. As one possible resolution of this kind of issues, 'International clean energy network using hydrogen conversion technology' which enables conversion of renewable energy from low cost hydropower into hydrogen energy and also into the transportable and storable form, is a meaningful concept. This system technology enables dealing of this hydrogen energy in international market as in the same manner as fossil fuel. It is considered to enable promotion of international and large scale introduction of such clean energy, along with the contribution to diversified and stabilized international energy supply. In this study, based upon the above-mentioned point of view and assumption of two sites, one on supply side and another on demand side of hydrogen energy, three systems are presumed. One of the systems consists of liquid hydrogen as transportation and storage medium of hydrogen, and the others intermediately convert hydrogen into methanol or ammonia as an energy carrier. A overall conceptual design of each system spanning from hydrogen production to its utilization, is conducted in practical way in order to review the general technical aspects and economical aspects through cost analysis. This study is administrated through the New Energy and Industrial Technology Development Organization (NEDO) as a part of the International Clean Energy Network Using Hydrogen Conversion (so-called WE-NET) Program with funding from

  9. Iron(II) porphyrins induced conversion of nitrite into nitric oxide: A computational study.

    Science.gov (United States)

    Zhang, Ting Ting; Liu, Yong Dong; Zhong, Ru Gang

    2015-09-01

    Nitrite reduction to nitric oxide by heme proteins was reported as a protective mechanism to hypoxic injury in mammalian physiology. In this study, the pathways of nitrite reduction to nitric oxide mediated by iron(II) porphyrin (P) complexes, which were generally recognized as models for heme proteins, were investigated by using density functional theory (DFT). In view of two type isomers of combination of nitrite and Fe(II)(P), N-nitro- and O-nitrito-Fe(II)-porphyrin complexes, and two binding sites of proton to the different O atoms of nitrite moiety, four main pathways for the conversion of nitrite into nitric oxide mediated by iron(II) porphyrins were proposed. The results indicate that the pathway of N-bound Fe(II)(P)(NO2) isomer into Fe(III)(P)(NO) and water is similar to that of O-bound isomer into nitric oxide and Fe(III)(P)(OH) in both thermodynamical and dynamical aspects. Based on the initial computational studies of five-coordinate nitrite complexes, the conversion of nitrite into NO mediated by Fe(II)(P)(L) complexes with 14 kinds of proximal ligands was also investigated. Generally, the same conclusion that the pathways of N-bound isomers are similar to those of O-bound isomer was obtained for iron(II) porphyrin with ligands. Different effects of ligands on the reduction reactions were also found. It is notable that the negative proximal ligands can improve reactive abilities of N-nitro-iron(II) porphyrins in the conversion of nitrite into nitric oxide compared to neutral ligands. The findings will be helpful to expand our understanding of the mechanism of nitrite reduction to nitric oxide by iron(II) porphyrins. Copyright © 2015 Elsevier Inc. All rights reserved.

  10. Scar formation and tuberculin conversion following BCG vaccination in infants: A prospective cohort study

    Directory of Open Access Journals (Sweden)

    Sara S Dhanawade

    2015-01-01

    Full Text Available Background: There is considerable variation in BCG scar failure rate on available data and correlation between BCG scar and tuberculin conversion remains controversial. Through this study we aimed to determine the scar failure rate and tuberculin conversion in term infants vaccinated with BCG within the first month. Materials and Methods: A prospective cohort study was conducted among 85 consecutive infants weighing >2 kg attending the immunization clinic of a medical college hospital. Fifteen subjects who could not complete the follow up were excluded. Total of 70 cases were analyzed. All babies were administered 0.1 ml of BCG and examined at 3 months (+1 week for scar. Tuberculin test was done with 5TU PPD. An induration of >5 mm was considered positive. Statistical analysis was done using Microsoft Excel and SPSS-22. Results: Out of the 70 infants, 41 (58.6% were males. Although majority (72.9% of infants were vaccinated within 7 days, only 18 (25.7% received BCG within 48 hours of birth. Sixty-four (91.4% had a visible scar at 12 weeks post vaccination representing a scar failure rate of 8.6%. Tuberculin test was positive in 50 (71.4%. The mean ± s.d. for scar and tuberculin skin test (TST reaction size was 4.93 ± 2.01 mm and 6.01 ± 3.22 mm, respectively. The association between scar formation and tuberculin positivity was highly significant (P < 0.001. There was significant correlation between scar size and TST size (r = 0.401, P = 0.001 Conclusions: Less than 10% of infants fail to develop a scar following BCG vaccination. There is good correlation between scar positivity and tuberculin conversion.

  11. Conversations About Goals and Values Are Feasible and Acceptable in Long-Term Acute Care Hospitals: A Pilot Study.

    Science.gov (United States)

    Lamas, Daniela J; Owens, Robert L; Nace, R Nicholas; Massaro, Anthony F; Pertsch, Nathan J; Moore, Susan T; Bernacki, Rachelle E; Block, Susan D

    2017-07-01

    The chronically critically ill have survived acute critical illness but require prolonged mechanical ventilation. These patients are frequently transferred from acute care to long-term acute care hospitals (LTACHs) for prolonged recovery, yet many suffer setbacks requiring readmission to acute care. The patient's relatively improved condition while at the LTACH might be an opportunity for communication regarding care goals; however, there have been no prior studies of the feasibility of such conversations in the LTACH. To determine the feasibility, acceptability, and potential usefulness of conversations about serious illness with chronic critical illness patients or their surrogate decision makers after LTACH admission. We adapted an existing conversation guide for use in chronically critically ill (defined by tracheotomy for prolonged ventilation) LTACH patients or their surrogates to explore views about quality of life, understanding of medical conditions, expectations, and planning for setbacks. These conversations were conducted by one interviewer and summarized for the patients' clinicians. We surveyed patients, surrogates, and clinicians to assess acceptability. A total of 70 subjects were approached and 50 (71%) were enrolled, including 30 patients and 20 surrogates. The median duration of the conversation was 14 minutes 45 seconds [IQR 12:46, 19]. The presence of ongoing mechanical ventilation did not lead to longer conversations; in fact, conversations with patients were shorter than those with surrogates. The majority of subjects (81%) described the conversation as worthwhile. The majority of clinicians (73%) reported that the conversation offered a new and significant understanding of the patient's preferences if a setback were to occur. Conversations about serious illness care goals can be accomplished in a relatively short period of time, are acceptable to chronically critically ill patients and their surrogate decision makers in the LTACH, and are

  12. Foresight Study on Advanced Conversion Technologies of Fossil Fuels; Estudio de Prospectiva Tecnologias Avanzadas de conversion de Combustibles Fosiles

    Energy Technology Data Exchange (ETDEWEB)

    Claver, A; Cabrera, J A [Ciemat, Madrid (Spain)

    2000-07-01

    The Observatorio de Prospectiva Tecnologica Industrial (OPTI) is a Foundation supported by the Ministry of Industry and Energy, (MINER) and has a main objective a basic information and knowledge on technology evolution. This information will be accessible to the Administration and to the Companies and can be taking into account in planning and decision making of technology policies. Ciemat is member of OPTI and is the organism in charge of the actions in the Energy sector. CIEMAT has the responsibility on the realisation of the sector studies to get in three years (1998 to 2001) a foresight vision of the critical technology topics. The OPTI integrated strategic plan undertake the analysis of other seven technology sectors, with the same criteria on methodological aspects. Delphi method was used for the realization of the studies. It consisted of a survey conducted in two rounds using a questionnaire to check the experts opinion. The time frame of the studies was defined from 1999 to 2015. (Author) 17 refs.

  13. System study of alternative waste management techniques: Final report

    International Nuclear Information System (INIS)

    1986-01-01

    This report summarizes the important results achieved in conjunction with the Research and Development Priority ''Alternative Waste Management Techniques'' sponsored by the Federal Ministry of Research and Technology from 1981 to 1984. The subject of these studies was solely ''direct disposal'' of spent fuel elements. For this purpose a reference concept was selected from a variety of possible processes and engineered in detailed form by firms in the nuclear industry. Those who worked on the engineering concepts consider this waste management method technically feasible. Several disposal casks have been fabricated. The basic licensability of direct disposal can be evaluated on the basis of the documentation developed by the companies. The direct disposal method was compared with the ''integrated waste management concept'' using reference fuel cycles with respect to the following criteria: radiological safety and nuclear material safeguards and, in addition, economic and energy-policy aspects. It was found that with respect to radiological safety, including the long-term safety of the final repository, there are no significant differences between the two fuel cycles with and without reprocessing. With respect to the nuclear material safeguards of a final repository containing spent fuel elements, there are still a number of unanswered questions. From an economic standpoint, direct disposal will be more economical in the foreseeable future than integrated waste management. Quantification of the effects of one or the other waste management method on the national economy is not necessarily possible. Reprocessing is supported primarily by technological and energy-policy considerations. On the basis of the results, the conclusion is reached that reprocessing should be pursued further, but that at the same time direct disposal should be developed to the point of practical maturity

  14. Depleted uranium management alternatives

    Energy Technology Data Exchange (ETDEWEB)

    Hertzler, T.J.; Nishimoto, D.D.

    1994-08-01

    This report evaluates two management alternatives for Department of Energy depleted uranium: continued storage as uranium hexafluoride, and conversion to uranium metal and fabrication to shielding for spent nuclear fuel containers. The results will be used to compare the costs with other alternatives, such as disposal. Cost estimates for the continued storage alternative are based on a life-cycle of 27 years through the year 2020. Cost estimates for the recycle alternative are based on existing conversion process costs and Capital costs for fabricating the containers. Additionally, the recycle alternative accounts for costs associated with intermediate product resale and secondary waste disposal for materials generated during the conversion process.

  15. Depleted uranium management alternatives

    International Nuclear Information System (INIS)

    Hertzler, T.J.; Nishimoto, D.D.

    1994-08-01

    This report evaluates two management alternatives for Department of Energy depleted uranium: continued storage as uranium hexafluoride, and conversion to uranium metal and fabrication to shielding for spent nuclear fuel containers. The results will be used to compare the costs with other alternatives, such as disposal. Cost estimates for the continued storage alternative are based on a life-cycle of 27 years through the year 2020. Cost estimates for the recycle alternative are based on existing conversion process costs and Capital costs for fabricating the containers. Additionally, the recycle alternative accounts for costs associated with intermediate product resale and secondary waste disposal for materials generated during the conversion process

  16. Alternate Communications Spectrum Study (ACSS) for Aviation Data Links (ADL)

    Science.gov (United States)

    Matolak, David W.

    2003-01-01

    The aim of the work was to identify the key factors involved in the use of alternate spectrum in various bands for a future integrated CNS data link. The study focused on systems and spectral bands that can deliver VDL-or-higher data rates in a two-way communication setting (including air-ground, ground-air, and air-air modes of operation), with multiple platforms (aircraft) operating in the same local environment. We begin with a review of the initial task list, and the final task list. The final task list contained a focus upon spectral availability and related systems that could be affected by the deployment of a new aviation data link (ADL) system. Most of this addresses the lower few layers of the communications protocol stack. A brief review of current related efforts in the aeronautical community is then provided, in which we describe several systems and programs of interest. Participation in some of these efforts is recommended. We also delineate several of the advantages and disadvantages of these system/efforts, in view of anticipated requirements of a new ADL. Desired attributes of a new ADL system are then discussed, and a connection with existing systems is made. The need to consider a wider set of alternative systems and technologies is described, and the beneficial aspects of a particular transmission technique- spread spectrum-are discussed. We then discuss in more detail several potential spectral regions, in terms of propagation conditions, available technology, spectrum availability, and waveform selection. Some comments on the need for standardization are also provided. We note that none of the existing systems described will likely meet the full range of desired features of a new ADL, but that several systems and spectral regions offer promise in terms of one or more characteristics. A system design and analysis approach is then provided. In this, we again focus on the lower few layers of the protocol stack, and aim to capture the main features

  17. Conversational sensemaking

    Science.gov (United States)

    Preece, Alun; Webberley, Will; Braines, Dave

    2015-05-01

    Recent advances in natural language question-answering systems and context-aware mobile apps create opportunities for improved sensemaking in a tactical setting. Users equipped with mobile devices act as both sensors (able to acquire information) and effectors (able to act in situ), operating alone or in collectives. The currently- dominant technical approaches follow either a pull model (e.g. Apple's Siri or IBM's Watson which respond to users' natural language queries) or a push model (e.g. Google's Now which sends notifications to a user based on their context). There is growing recognition that users need more flexible styles of conversational interaction, where they are able to freely ask or tell, be asked or told, seek explanations and clarifications. Ideally such conversations should involve a mix of human and machine agents, able to collaborate in collective sensemaking activities with as few barriers as possible. Desirable capabilities include adding new knowledge, collaboratively building models, invoking specific services, and drawing inferences. As a step towards this goal, we collect evidence from a number of recent pilot studies including natural experiments (e.g. situation awareness in the context of organised protests) and synthetic experiments (e.g. human and machine agents collaborating in information seeking and spot reporting). We identify some principles and areas of future research for "conversational sensemaking".

  18. Study on Alternative Cargo Launch Options from the Lunar Surface

    Energy Technology Data Exchange (ETDEWEB)

    Cheryl A. Blomberg; Zamir A. Zulkefli; Spencer W. Rich; Steven D. Howe

    2013-07-01

    In the future, there will be a need for constant cargo launches from Earth to Mars in order to build, and then sustain, a Martian base. Currently, chemical rockets are used for space launches. These are expensive and heavy due to the amount of necessary propellant. Nuclear thermal rockets (NTRs) are the next step in rocket design. Another alternative is to create a launcher on the lunar surface that uses magnetic levitation to launch cargo to Mars in order to minimize the amount of necessary propellant per mission. This paper investigates using nuclear power for six different cargo launching alternatives, as well as the orbital mechanics involved in launching cargo to a Martian base from the moon. Each alternative is compared to the other alternative launchers, as well as compared to using an NTR instead. This comparison is done on the basis of mass that must be shipped from Earth, the amount of necessary propellant, and the number of equivalent NTR launches. Of the options, a lunar coil launcher had a ship mass that is 12.7% less than the next best option and 17 NTR equivalent launches, making it the best of the presented six options.

  19. Conversational Implicatures in English Plays and Their Persian Translations: A Norm-governed Study

    Directory of Open Access Journals (Sweden)

    Zahra Hassani Laharomi

    2013-09-01

    Full Text Available The present study attempted to describe in full detail the status of implicature translation in two 20-year time periods before and after Iran Islamic Revolution to provide a clear picture of the strategies applied by translators in the two eras and, as its main objective, to shed light on the translational norms of this linguistic element. To this end, it first sought to elaborate on the reasons and the ways they emerge in conversations. Accordingly, identifying the implicatures arose due to the violation of Grice’s (1975 four maxims of conversation, the researcher separately categorized the translations of the implicatures based on Desilla’s (2009 classification. As the last phase of the study, the strategies for implicature translation were thoroughly scrutinized with the hope to determine the dominant norms of implicature translation in light of Toury’s (1995 notion of initial norm. Based on the results obtained from both pre- and post-revolution data, preservation was revealed to be the most frequent strategy in both eras, attesting to the significance of the adequacy of implicature translation; modification and explicitation were the second and the third most frequent strategies respectively. However, the frequency of modification and explicitation increased in the post-revolution translations. It seems that the trend of the norm of implicature translation moves toward acceptability.

  20. Rough order of magnitude cost estimate for immobilization of 50 MT of plutonium sharing existing facilities at Hanford with pit disassembly and conversion facility: alternative 11

    International Nuclear Information System (INIS)

    DiSabatino, A.

    1998-01-01

    The purpose of this Cost Estimate Report is to identify preliminary capital and operating costs for a facility to immobilize 50 metric tons (nominal) of plutonium as a ceramic in an existing facility at Hanford, the Fuels and Materials Examination Facility (FMEF). The Pit Disassembly and Conversion Facility (PDCF), which is being costed in a separate report by LANL, will also be located in the FMEF in this co-location option

  1. CO2 injection into submarine, CH4-hydrate bearing sediments: Parameter studies towards the development of a hydrate conversion technology

    Science.gov (United States)

    Deusner, Christian; Bigalke, Nikolaus; Kossel, Elke; Haeckel, Matthias

    2013-04-01

    In the recent past, international research efforts towards exploitation of submarine and permafrost hydrate reservoirs have increased substantially. Until now, findings indicate that a combination of different technical means such as depressurization, thermal stimulation and chemical activation is the most promising approach for producing gas from natural hydrates. Moreover, emission neutral exploitation of CH4-hydrates could potentially be achieved in a combined process with CO2 injection and storage as CO2-hydrate. In the German gas hydrate initiative SUGAR, a combination of experimental and numerical studies is used to elucidate the process mechanisms and technical parameters on different scales. Experiments were carried out in the novel high-pressure flow-through system NESSI (Natural Environment Simulator for sub-Seafloor Interactions). Recent findings suggest that the injection of heated, supercritical CO2 is beneficial for both CH4 production and CO2 retention. Among the parameters tested so far are the CO2 injection regime (alternating vs. continuous injection) and the reservoir pressure / temperature conditions. Currently, the influence of CO2 injection temperature is investigated. It was shown that CH4 production is optimal at intermediate reservoir temperatures (8 ° C) compared to lower (2 ° C) and higher temperatures (10 ° C). The reservoir pressure, however, was of minor importance for the production efficiency. At 8 ° C, where CH4- and CO2-hydrates are thermodynamically stable, CO2-hydrate formation appears to be slow. Eventual clogging of fluid conduits due to CO2-rich hydrate formation force open new conduits, thereby tapping different regions inside the CH4-hydrate sample volume for CH4gas. In contrast, at 2 ° C immediate formation of CO2-hydrate results in rapid and irreversible obstruction of the entire pore space. At 10 ° C pure CO2-hydrates can no longer be formed. Consequently the injected CO2 flows through quickly and interaction with

  2. The MAX Statistic is Less Powerful for Genome Wide Association Studies Under Most Alternative Hypotheses.

    Science.gov (United States)

    Shifflett, Benjamin; Huang, Rong; Edland, Steven D

    2017-01-01

    Genotypic association studies are prone to inflated type I error rates if multiple hypothesis testing is performed, e.g., sequentially testing for recessive, multiplicative, and dominant risk. Alternatives to multiple hypothesis testing include the model independent genotypic χ 2 test, the efficiency robust MAX statistic, which corrects for multiple comparisons but with some loss of power, or a single Armitage test for multiplicative trend, which has optimal power when the multiplicative model holds but with some loss of power when dominant or recessive models underlie the genetic association. We used Monte Carlo simulations to describe the relative performance of these three approaches under a range of scenarios. All three approaches maintained their nominal type I error rates. The genotypic χ 2 and MAX statistics were more powerful when testing a strictly recessive genetic effect or when testing a dominant effect when the allele frequency was high. The Armitage test for multiplicative trend was most powerful for the broad range of scenarios where heterozygote risk is intermediate between recessive and dominant risk. Moreover, all tests had limited power to detect recessive genetic risk unless the sample size was large, and conversely all tests were relatively well powered to detect dominant risk. Taken together, these results suggest the general utility of the multiplicative trend test when the underlying genetic model is unknown.

  3. Cultural Studies Methodologies and Narrative Family Therapy: Therapeutic Conversations About Pop Culture.

    Science.gov (United States)

    Tilsen, Julie; Nylund, David

    2016-06-01

    Therapists recognize that popular media culture is an influential force that shapes identities and relationships in contemporary society. Indeed, people have serious relationships with the commodities and practices that emerge from pop culture. However, they often lack the conceptual and conversational resources to engage meaningfully with clients about pop culture's influence in their lives. Cultural studies is introduced as an interdisciplinary approach that provides frameworks for both theory and practice that position therapists and clients to critically examine the role of pop culture in their lives. Cultural studies and narrative therapy are discussed as praxis allies that share a populist political intention and counter-hegemonic discursive practices. The integration of cultural studies methodologies into narrative therapy practice with a parent and her teenage daughter is illustrated through a case vignette. © 2016 Family Process Institute.

  4. Inertial confinement fusion reaction chamber and power conversion system study. Final report

    International Nuclear Information System (INIS)

    Maya, I.; Schultz, K.R.; Bourque, R.F.

    1985-10-01

    This report summarizes the results of the second year of a two-year study on the design and evaluation of the Cascade concept as a commercial inertial confinement fusion (ICF) reactor. We developed a reactor design based on the Cascade reaction chamber concept that would be competitive in terms of both capital and operating costs, safe and environmentally acceptable in terms of hazard to the public, occupational exposure and radioactive waste production, and highly efficient. The Cascade reaction chamber is a double-cone-shaped rotating drum. The granulated solid blanket materials inside the rotating chamber are held against the walls by centrifugal force. The fusion energy is captured in a blanket of solid carbon, BeO, and LiAlO 2 granules. These granules are circulated to the primary side of a ceramic heat exchanger. Primary-side granule temperatures range from 1285 K at the LiAlO 2 granule heat exchanger outlet to 1600 K at the carbon granule heat exchanger inlet. The secondary side consists of a closed-cycle gas turbine power conversion system with helium working fluid, operating at 1300 K peak outlet temperature and achieving a thermal power conversion efficiency of 55%. The net plant efficiency is 49%. The reference design is a plant producing 1500 MW of D-T fusion power and delivering 815 MW of electrical power for sale to the utility grid. 88 refs., 44 figs., 47 tabs

  5. A comprehensive study of neutrino spin-flavour conversion in supernovae and the neutrino mass hierarchy

    Science.gov (United States)

    Ando, Shin'ichiro; Sato, Katsuhiko

    2003-10-01

    Resonant spin-flavour (RSF) conversions of supernova neutrinos, which are induced by the interaction between the nonzero neutrino magnetic moment and supernova magnetic fields, are studied for both normal and inverted mass hierarchy. As the case for the pure matter-induced neutrino oscillation (Mikheyev–Smirnov–Wolfenstein (MSW) effect), we find that the RSF transitions are strongly dependent on the neutrino mass hierarchy as well as the value of θ13. Flavour conversions are solved numerically for various neutrino parameter sets, with the presupernova profile calculated by Woosley and Weaver. In particular, it is very interesting that the RSF-induced νe→bar nue transition occurs if the following conditions are all satisfied: the value of μνB (μν is the neutrino magnetic moment and B is the magnetic field strength) is sufficiently strong, the neutrino mass hierarchy is inverted, and the value of θ13 is large enough to induce adiabatic MSW resonance. In this case, the strong peak due to the original νe emitted from the neutronization burst would exist in the time profile of the neutrino events detected at the Super-Kamiokande detector. If this peak were observed in reality, it would provide fruitful information on the neutrino properties. On the other hand, the characteristics of the neutrino spectra are also different between the neutrino models, but we find that there remains degeneracy among several models. Dependence on presupernova models is also discussed.

  6. Study of the coefficients of internal conversion for transition energies approaching the threshold

    International Nuclear Information System (INIS)

    Farani Coursol, Nelcy.

    1979-01-01

    Internal conversion coefficients were determined experimentally with great accuracy for areas of transition energies, which constitute tests for the theories (energies at the most ten kEv above the threshold of K shell), then the results obtained were compared with the values calculated (or to be calculated) from theoretical models. Owing to the difficulties raised by the precise determination of the internal conversion coefficients (ICC), in the first stage we selected radionuclides with a relatively simple decay pattern, the transitions: 30 keV of sup(93m)Nb, 35 keV of sup(125m)Te, 14 keV of 57 Fe and 39 keV of sup(129m)Xe. It was observed that 'problems' exist with respect to the ICC's of the great multipolarity transitions, so the transitions of this kind were examined in a systematic manner. The possibility of penetration effects occurring for the transitions studied experimentally was examined. The considerations are presented which 'authorized' us to disregard the dynamic part of the ICC for the transitions approaching the threshold (L selection rules and life of nuclear levels in relation to Weisskopf-Moszkowski estimations). The Kurie straight line was determined experimentally for the β - transition and the Qsub(β) was evaluated with an important accuracy gain compared with the values available at present. Finally, a certain number of ICC's of transitions already determined with good precision were recalculated, in order to extend our analysis and detect any possible systematic errors [fr

  7. Sodium-Bearing Waste Treatment Alternatives Implementation Study

    Energy Technology Data Exchange (ETDEWEB)

    Charles M. Barnes; James B. Bosley; Clifford W. Olsen

    2004-07-01

    The purpose of this document is to discuss issues related to the implementation of each of the five down-selected INEEL/INTEC radioactive liquid waste (sodium-bearing waste - SBW) treatment alternatives and summarize information in three main areas of concern: process/technical, environmental permitting, and schedule. Major implementation options for each treatment alternative are also identified and briefly discussed. This report may touch upon, but purposely does not address in detail, issues that are programmatic in nature. Examples of these include how the SBW will be classified with respect to the Nuclear Waste Policy Act (NWPA), status of Waste Isolation Pilot Plant (WIPP) permits and waste storage availability, available funding for implementation, stakeholder issues, and State of Idaho Settlement Agreement milestones. It is assumed in this report that the SBW would be classified as a transuranic (TRU) waste suitable for disposal at WIPP, located in New Mexico, after appropriate treatment to meet transportation requirements and waste acceptance criteria (WAC).

  8. A Study on the RF-DC Conversion Efficiency of Microstrip Patch Rectenna

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Yang Ha; Youn, Dong Gi; Kim, Kwan Ho [Korea Electrotechnology Research Institute (Korea); Rhee, Young Chul [Kyungnam University (Korea)

    2000-07-01

    We designed and manufactured microstrip patch antenna mainly used in the rectenna and then analysed RF-DC conversion efficiency of wireless power transmission system. We analyse conversion efficiency of load, direction of linear and dual polization rectenna. We found that the maximum efficiency would be about 70% of load and direction in patch type. In conclusion, we found that total conversion efficiency is 64% - 71% in patch Rectenna. (author). 5 refs., 8 figs., 1 tab.

  9. Parametric study on thermal-hydraulic characteristics of high conversion light water reactor

    International Nuclear Information System (INIS)

    Mori, Takamasa; Nakagawa, Masayuki; Fujii, Sadao.

    1988-11-01

    To assess the feasibility of high conversion light water reactors (HCLWRs) from the thermal-hydraulic viewpoint, parametric study on thermal-hydraulic characteristics of HCLWR has been carried out by using a unit cell model. It is assumed that a HCLWR core is contained in a current 1000 MWe PWR plant. At the present study, reactor core parameters such as fuel pin diameter, pitch, core height and linear heat rate are widely and parametrically changed to survey the relation between these parameters and the basic thermal-hydraulic characteristics, i.e. maximum fuel temperature, minimum DNBR, reduction of reactor thermal output and so on. The validity of the unit cell model used has been ensured by comparison with the result of a subchannel analysis carried out for a whole core. (author)

  10. Reactor core conversion studies of Ghana: Research Reactor-1 and proposal for addition of safety rod

    International Nuclear Information System (INIS)

    Odoi, H.C.

    2014-06-01

    The inclusion of an additional safety rod in conjunction with a core conversion study of Ghana Research Reactor-1 (GHARR-1) was carried out using neutronics, thermal hydraulics and burnup codes. The study is based on a recommendation by Integrated Safety Assessment for Research Reactors (INSARP) mission to incorporate a safety rod to the reactor safety system as well as the need to replace the reactor fuel with LEU. Conversion from one fuel type to another requires a complete re-evaluation of the safety analysis. Changes to the reactivity worth, shutdown margin, power density and material properties must be taken into account, and appropriate modifications made. Neutronics analysis including burnup was studied followed by thermal hydraulics analyses which comprise steady state and transients. Four computer codes were used for the analysis; MCNP, REBUS, PLTEP and PARET. The neutronics analysis revealed that the LEU core must be operated at 34 Kw in order to attain the flux of 1.0E12 n/cm 2 .s as the nominal flux of the HEU core. The auxiliary safety rod placed at a modified irradiation site gives a better worth than the cadmium capsules. For core excess reactivity of 4 mk, 348 fuel pins would be appropriate for the GHARR-1 LEU core. Results indicate that flux level of 1.0E12 n/cm 2 .s in the inner irradiation channel will not be compromised, if the power of the LEU core is increased to 34 kW. The GHARR-1 core using LEU-U0 2 -12.5% fuel can be operated for 23 shim cycles, with cycles length 2.5 years, for over 57 years at the 17 kW power level. All 23 LEU cycles meet the ∼ 4.0 mk excess reactivity required at the beginning of cycle . For comparison, the MNSR HEU reference core can also be operated for 23 shim cycles, but with a cycle length of 2.0 years for just over 46 years at 15.0kW power level. It is observed that the GHARR-1 core with LEU UO 2 fuel enriched to 12.5% and a power level of 34 kW can be operated ∼25% longer than the current HEU core operated at

  11. A diagnosis of bipolar spectrum disorder predicts diagnostic conversion from unipolar depression to bipolar disorder: a 5-year retrospective study.

    Science.gov (United States)

    Woo, Young Sup; Shim, In Hee; Wang, Hee-Ryung; Song, Hoo Rim; Jun, Tae-Youn; Bahk, Won-Myong

    2015-03-15

    The major aims of this study were to identify factors that may predict the diagnostic conversion from major depressive disorder (MDD) to bipolar disorder (BP) and to evaluate the predictive performance of the bipolar spectrum disorder (BPSD) diagnostic criteria. The medical records of 250 patients with a diagnosis of MDD for at least 5 years were retrospectively reviewed for this study. The diagnostic conversion from MDD to BP was observed in 18.4% of 250 MDD patients, and the diagnostic criteria for BPSD predicted this conversion with high sensitivity (0.870) and specificity (0.917). A family history of BP, antidepressant-induced mania/hypomania, brief major depressive episodes, early age of onset, antidepressant wear-off, and antidepressant resistance were also independent predictors of this conversion. This study was conducted using a retrospective design and did not include structured diagnostic interviews. The diagnostic criteria for BPSD were highly predictive of the conversion from MDD to BP, and conversion was associated with several clinical features of BPSD. Thus, the BPSD diagnostic criteria may be useful for the prediction of bipolar diathesis in MDD patients. Copyright © 2014 Elsevier B.V. All rights reserved.

  12. Alternative Forms of Energy Production and Political Reconfigurations: The Sociology of Alternative Energies as a Study of Collective Reorganization Potential

    International Nuclear Information System (INIS)

    Rumpala, Yannick

    2013-01-01

    Energy choices that are made in a society are also political choices. This article aims to study the extent to which these choices can be reoriented by technological developments related to renewable energies, thus contributing to a redistribution of possibilities and to social reorganization. Three steps are proposed to show that while the development of alternative energies depends on technological advances, it can, in this process, also reveal political potentials: 1) the first step clarifies the theoretical arguments that can be deployed in favour of an approach in terms of 'technological potentialism'; 2) the second step extends this approach by identifying a set of potentials linked to renewable energies and the model that could take shape through these alternative forms; 3) the third step examines how these potentials could find ways of being updated

  13. Training conversation partners of persons with communication disorders related to Parkinson's disease--a protocol and a pilot study.

    Science.gov (United States)

    Forsgren, Emma; Antonsson, Malin; Saldert, Charlotta

    2013-07-01

    This paper reports on the adaptation of a training programme for conversation partners of persons with Parkinson's disease, and a protocol for assessment of possible changes in conversational interaction as a result of intervention. We present data from an explorative multiple case study with three individuals with Parkinson's disease and their spouses. Repeated analysis of natural conversational interaction and measures of the participants' perception of communication as well as measures of different cognitive abilities were obtained. The results show that the communication in all three dyads was affected by both speech and language problems and that the conversation training model and the assessment protocol may work well after minor adjustments. Influence of different aspects of cognition on communication is discussed.

  14. Illustrative Case Study: Life Cycle Assessment of Four Window Alternatives

    DEFF Research Database (Denmark)

    Owsianiak, Mikołaj; Bjørn, Anders; Bugge, Heidi

    2018-01-01

    This report serves as an example report on how to perform an LCA according to the guidance given in Chap. 37 and how to structure the report according to the reporting template in Chap. 38. The goals of the LCA were (i) to perform a benchmarking of a prototype wood/composite (W/C) window made out...... of glass fibre against three alternative window types currently offered in the market (made of wood (W), wood/aluminium (W/ALU), and PVC) and (ii) to identify environmental hotspots for each window system....

  15. Greenfield Alternative Study LEU-Mo Fuel Fabrication Facility

    Energy Technology Data Exchange (ETDEWEB)

    Washington Division of URS

    2008-07-01

    This report provides the initial “first look” of the design of the Greenfield Alternative of the Fuel Fabrication Capability (FFC); a facility to be built at a Greenfield DOE National Laboratory site. The FFC is designed to fabricate LEU-Mo monolithic fuel for the 5 US High Performance Research Reactors (HPRRs). This report provides a pre-conceptual design of the site, facility, process and equipment systems of the FFC; along with a preliminary hazards evaluation, risk assessment as well as the ROM cost and schedule estimate.

  16. Studies on the conversion of cellulose hydrolysate into citric acid by Aspergillus niger

    Energy Technology Data Exchange (ETDEWEB)

    Manonmani, H.K.; Sreekantiah, K.R.

    1987-06-01

    The production of citric acid by Aspergillus niger (16) was studied using enzymatic hydrolysate of alkali-treated bagasse by solid state fermentation. Saccharification and fermentations were carried out sequentially as well as simultaneously. Conditions for optimum citric acid production using cellulose hydrolysate medium were: sugar concentration: 7% (w/w); NaNO/sub 3/; 400 mg/N/sub 2//l medium; KH/sub 2/PO/sub 4/:/0.1%/l medium; ethanol: 3% (v/w); 1 ml of 1 x 10 squared m fluoroacetate and coconut oil: 3% (v/w). Simultaneous saccharification and fermentation was not found to be suitable for citric acid production. 44% conversion of total reducing sugars to citric acid was obtained in 72 hours fermentation by sequential process with the above mentioned parameters. (Refs. 15).

  17. Ab initio design of nanostructures for solar energy conversion: a case study on silicon nitride nanowire.

    Science.gov (United States)

    Pan, Hui

    2014-01-01

    Design of novel materials for efficient solar energy conversion is critical to the development of green energy technology. In this work, we present a first-principles study on the design of nanostructures for solar energy harvesting on the basis of the density functional theory. We show that the indirect band structure of bulk silicon nitride is transferred to direct bandgap in nanowire. We find that intermediate bands can be created by doping, leading to enhancement of sunlight absorption. We further show that codoping not only reduces the bandgap and introduces intermediate bands but also enhances the solubility of dopants in silicon nitride nanowires due to reduced formation energy of substitution. Importantly, the codoped nanowire is ferromagnetic, leading to the improvement of carrier mobility. The silicon nitride nanowires with direct bandgap, intermediate bands, and ferromagnetism may be applicable to solar energy harvesting.

  18. Fundamental Studies of Charge Migration and Delocalization Relevant to Solar Energy Conversion

    Energy Technology Data Exchange (ETDEWEB)

    Michael J. Therien

    2012-06-01

    This program aimed to understand the molecular-level principles by which complex chemical systems carry out photochemical charge separation, transport, and storage, and how these insights could impact the design of practical solar energy conversion and storage devices. Towards these goals, this program focused on: (1) carrying out fundamental mechanistic and transient dynamical studies of proton-coupled electron-transfer (PCET) reactions; (2) characterizing and interrogating via electron paramagnetic resonance (EPR) spectroscopic methods novel conjugated materials that feature large charge delocalization lengths; and (3) exploring excitation delocalization and migration, as well as polaron transport properties of meso-scale assemblies that are capable of segregating light-harvesting antennae, nanoscale wire-like conduction elements, and distinct oxidizing and reducing environments.

  19. Comparative study of energy conversion system dedicated to a small wind turbine

    International Nuclear Information System (INIS)

    Mirecki, A.

    2005-01-01

    This study presents a comparison of architectures and strategies of energy management dedicated to VAWT turbines such as Savonius. A Maximum Power Point Tracking must be implemented in order to optimize the energetic behavior. A torque or a speed control, or an indirect control of the DC bus current is possible. In the fact that the wind turbine characteristic is unknown, an operational research based on fuzzy logic is proposed. Aiming to minimize the cost of the static conversion structure, simple structures (diode bridge inverter, associated with DC-DC chopper) are analyzed and compared with a system based on a PWM Voltage Source Inverter. A test bench has been realized in the meantime as a system simulation. Comparisons of the provided energy are made for different wind speeds allowing to evaluate the performance of each structure and of the control strategies. (author)

  20. A Conversational Model for Qualitative Research: A Case Study of Clergy and Religious Knowledge

    Science.gov (United States)

    Roland, Daniel; Wicks, Don A.

    2009-01-01

    This paper describes the qualitative research interview as a conversation designed to gain understanding of the world of research informants. It illustrates the potential of the qualitative research interview when the researcher is able to enter into and maintain a conversation with the research informant as an insider in the latter's community.…

  1. Using biofuel tracers to study alternative combustion regimes

    International Nuclear Information System (INIS)

    Mack, J.H.; Flowers, D.L.; Buchholz, B.A.; Dibble, R.W.

    2007-01-01

    Interest in the use of alternative fuels and engines is increasing as the price of petroleum climbs. The inherently higher efficiency of Diesel engines has led to increased adoption of Diesels in Europe, capturing approximately 40% of the new passenger car market. Unfortunately, lower CO 2 emissions are countered with higher nitrogen oxides (NO x ) and particulate matter (PM) emissions and higher noise. Adding oxygenated compounds to the fuel helps reduce PM emissions. However, relying on fuel alone to reduce PM is unrealistic due to economic constraints and difficult due to the emerging PM standards. Keeping peak combustion temperature below 1700 K inhibits NO x formation. Altering the combustion regime to burn at temperatures below the NO x threshold and accept a wide variety of fuels seems like a promising alternative for future engines. Homogeneous charge compression ignition (HCCI) is a possible solution. Fuel and air are well mixed prior to intake into a cylinder (homogeneous charge) and ignition occurs by compression of the fuel-air mixture by the piston. HCCI is rapid and relatively cool, producing little NO x and PM. Unfortunately, it is hard to control since HCCI is initiated by temperature and pressure instead of a spark or direct fuel injection. We investigate biofuel HCCI combustion, and use intrinsically labeled biofuels as tracers of HCCI combustion. Data from tracer experiments are used to improve our combustion modeling

  2. The design study of an ultra-high power EB/X-ray conversion facility

    Energy Technology Data Exchange (ETDEWEB)

    He, Zi-Feng, E-mail: hezifeng@sinap.ac.cn; Li, Deming; Huang, Jian-Ming; Yang, Yong-Jin; Zhu, Xi-Kai; Zhang, Yu-Tian

    2014-10-15

    Highlights: • We describe a 100 kW electron beam to X-rays conversion system. • We give an idea to improve the conversion efficiency and lifetime of the target. • We describe the design and thermal characteristics of the X-ray converter. - Abstract: X-ray conversion is a frequent need for irradiating the products that cannot be processed by electron beams, duo to their limited penetration capacity in materials, in radiation sterilization of disposable healthcare products and food irradiation. In this paper, we report the design of a conversion facility with a 5-MeV/120-kW electron accelerator, regarding the considerations on selection of the target materials and target structure, design of the electron beam transport line and approaches to improve the conversion efficiency and lifetime.

  3. Final Technical Report for Alternative Fuel Source Study-An Energy Efficient and Environmentally Friendly Approach

    Energy Technology Data Exchange (ETDEWEB)

    Zee, Ralph [Auburn University, AL (United States); Schindler, Anton [Auburn University, AL (United States); Duke, Steve [Auburn University, AL (United States); Burch, Thom [Auburn University, AL (United States); Bransby, David [Auburn University, AL (United States); Stafford, Don [Lafarge North America, Inc., Alpharetta, GA (United States)

    2010-08-31

    The objective of this project is to conduct research to determine the feasibility of using alternate fuel sources for the production of cement. Successful completion of this project will also be beneficial to other commercial processes that are highly energy intensive. During this report period, we have completed all the subtasks in the preliminary survey. Literature searches focused on the types of alternative fuels currently used in the cement industry around the world. Information was obtained on the effects of particular alternative fuels on the clinker/cement product and on cement plant emissions. Federal regulations involving use of waste fuels were examined. Information was also obtained about the trace elements likely to be found in alternative fuels, coal, and raw feeds, as well as the effects of various trace elements introduced into system at the feed or fuel stage on the kiln process, the clinker/cement product, and concrete made from the cement. The experimental part of this project involves the feasibility of a variety of alternative materials mainly commercial wastes to substitute for coal in an industrial cement kiln in Lafarge NA and validation of the experimental results with energy conversion consideration.

  4. In operando spectroscopic studies of high temperature electrocatalysts used for energy conversion

    Science.gov (United States)

    McIntyre, Melissa Dawn

    Solid-state electrochemical cells are efficient energy conversion devices that can be used for clean energy production or for removing air pollutants from exhaust gas emitted by combustion processes. For example, solid oxide fuel cells generate electricity with low emissions from a variety of fuel sources; solid oxide electrolysis cells produce zero-emission H2 fuel; and solid-state DeNOx cells remove NOx gases from diesel exhaust. In order to maintain high conversion efficiencies, these systems typically operate at temperatures ≥ 500°C. The high operating temperatures, however, accelerate chemical and mechanical cell degradation. To improve device durability, a mechanistic understanding of the surface chemistry occurring at the cell electrodes (anode and cathode) is critical in terms of refining cell design, material selection and operation protocols. The studies presented herein utilized in operando Raman spectroscopy coupled with electrochemical measurements to directly correlate molecular/material changes with device performance in solid oxide cells under various operating conditions. Because excessive carbon accumulation with carbon-based fuels destroys anodes, the first three studies investigated strategies for mitigating carbon accumulation on Ni cermet anodes. Results from the first two studies showed that low amounts of solid carbon stabilized the electrical output and improved performance of solid oxide fuel cells operating with syn-gas (H 2/CO fuel mixture). The third study revealed that infiltrating anodes with Sn or BaO suppressed carbon accumulation with CH4 fuel and that H2O was the most effective reforming agent facilitating carbon removal. The last two studies explored how secondary phases formed in traditional solid oxide cell materials doped with metal oxides improve electrochemical performance. Results from the fourth study suggest that the mixed ion-electron conducting Zr5Ti7O24 secondary phase can expand the electrochemically active region

  5. A Floating Ocean Energy Conversion Device and Numerical Study on Buoy Shape and Performance

    Directory of Open Access Journals (Sweden)

    Ruiyin Song

    2016-05-01

    Full Text Available Wave and current energy can be harnessed in the East China Sea and South China Sea; however, both areas are subject to high frequencies of typhoon events. To improve the safety of the ocean energy conversion device, a Floating Ocean Energy Conversion Device (FOECD with a single mooring system is proposed, which can be towed to avoid severe ocean conditions or for regular maintenance. In this paper, the structure of the FOECD is introduced, and it includes a catamaran platform, an oscillating buoy part, a current turbine blade, hydraulic energy storage and an electrical generation part. The numerical study models the large catamaran platform as a single, large buoy, while the four floating buoys were modeled simply as small buoys. Theoretical models on wave energy power capture and efficiency were established. To improve the suitability of the buoy for use in the FOECD and its power harvesting capability, a numerical simulation of the four buoy geometries was undertaken. The shape profiles examined in this paper are cylindrical, turbinate (V-shaped and U-shaped cone with cylinder, and combined cylinder-hemisphere buoys. Simulation results reveal that the suitability of a turbinate buoy is the best of the four types. Further simulation models were carried out by adjusting the tip radius of the turbinate buoy. Three performance criteria including suitability, power harvesting capability and energy capture efficiency were analyzed. It reveals that the turbinate buoy has almost the same power harvesting capabilities and energy capture efficiency, while its suitability is far better than that of a cylindrical buoy.

  6. Comparative study of energy conversion system dedicated to a small wind turbine; Etude comparative de chaines de conversion d'energie dediees a une eolienne de petite puissance

    Energy Technology Data Exchange (ETDEWEB)

    Mirecki, A

    2005-07-01

    This study presents a comparison of architectures and strategies of energy management dedicated to VAWT turbines such as Savonius. A Maximum Power Point Tracking must be implemented in order to optimize the energetic behavior. A torque or a speed control, or an indirect control of the DC bus current is possible. In the fact that the wind turbine characteristic is unknown, an operational research based on fuzzy logic is proposed. Aiming to minimize the cost of the static conversion structure, simple structures (diode bridge inverter, associated with DC-DC chopper) are analyzed and compared with a system based on a PWM Voltage Source Inverter. A test bench has been realized in the meantime as a system simulation. Comparisons of the provided energy are made for different wind speeds allowing to evaluate the performance of each structure and of the control strategies. (author)

  7. Feasibility study on AFR-100 fuel conversion from uranium-based fuel to thorium-based fuel

    Energy Technology Data Exchange (ETDEWEB)

    Heidet, F.; Kim, T.; Grandy, C. (Nuclear Engineering Division)

    2012-07-30

    Although thorium has long been considered as an alternative to uranium-based fuels, most of the reactors built to-date have been fueled with uranium-based fuel with the exception of a few reactors. The decision to use uranium-based fuels was initially made based on the technology maturity compared to thorium-based fuels. As a result of this experience, lot of knowledge and data have been accumulated for uranium-based fuels that made it the predominant nuclear fuel type for extant nuclear power. However, following the recent concerns about the extent and availability of uranium resources, thorium-based fuels have regained significant interest worldwide. Thorium is more abundant than uranium and can be readily exploited in many countries and thus is now seen as a possible alternative. As thorium-based fuel technologies mature, fuel conversion from uranium to thorium is expected to become a major interest in both thermal and fast reactors. In this study the feasibility of fuel conversion in a fast reactor is assessed and several possible approaches are proposed. The analyses are performed using the Advanced Fast Reactor (AFR-100) design, a fast reactor core concept recently developed by ANL. The AFR-100 is a small 100 MW{sub e} reactor developed under the US-DOE program relying on innovative fast reactor technologies and advanced structural and cladding materials. It was designed to be inherently safe and offers sufficient margins with respect to the fuel melting temperature and the fuel-cladding eutectic temperature when using U-10Zr binary metal fuel. Thorium-based metal fuel was preferred to other thorium fuel forms because of its higher heavy metal density and it does not need to be alloyed with zirconium to reduce its radiation swelling. The various approaches explored cover the use of pure thorium fuel as well as the use of thorium mixed with transuranics (TRU). Sensitivity studies were performed for the different scenarios envisioned in order to determine the

  8. Conceptual design of the blanket and power conversion system for a mirror hybrid fusion-fission reactor. Addendum 1. Alternate concepts. 12-month progress report addendum, July 1, 1975--June 30, 1976

    International Nuclear Information System (INIS)

    Schultz, K.R.; Dee, J.B.; Backus, G.A.; Culver, D.W.

    1976-01-01

    During the course of the Mirror Hybrid Fusion-Fission Reactor study several alternate concepts were considered for various reactor components. Several of the alternate concepts do appear to exhibit features with potential advantage for use in the mirror hybrid reactor. These are described and should possibly be investigated further in the future

  9. The conversion of the DIDO-type reactor FRJ-2. Studies and conclusions

    International Nuclear Information System (INIS)

    Stroemich, A.; Siebertz, Ch.; Wickert, M.

    1985-01-01

    For the FRJ-2 (23 MW) of the KFA-Juelich the conversion from HEU- to LEU-fuel was investigated. Before starting the conversion calculations our methods were qualified for the application to heavy water moderated research reactors. A combination of LEU-elements with two different U-235 loadings of 180 g and 225 g was found as suitable for conversion. With these LEU-elements a working core and a transition phase was calculated. The change of the mechanical fuel element design was taken into account. (author)

  10. Factors Affecting Time to Sputum Culture Conversion in Adults with Pulmonary Tuberculosis: A Historical Cohort Study without Censored Cases.

    Science.gov (United States)

    Kanda, Rie; Nagao, Taishi; Tho, Nguyen Van; Ogawa, Emiko; Murakami, Yoshitaka; Osawa, Makoto; Saika, Yoshinori; Doi, Kenji; Nakano, Yasutaka

    2015-01-01

    In patients with pulmonary tuberculosis (TB), shortening the time to sputum culture conversion is desirable to reduce the likelihood of mycobacterial transmission. A persistent positive sputum culture after 2 months of treatment is reported to be associated with the presence of cavitation and the extent of disease on chest X-ray, high colony count, diabetes mellitus, and smoking. However, little is known about factors affecting the time to sputum culture conversion. This study was conducted to evaluate factors affecting the time to sputum culture conversion throughout the course of treatment in adults with pulmonary TB. This study was performed using a database of the medical records of patients with active pulmonary TB who were treated at Hirakata Kohsai Hospital in Hirakata City, Osaka, Japan, from October 2000 to October 2002. Cox proportional-hazards analysis was used to evaluate factors affecting the time to sputum culture conversion after adjusting for potential confounders. The data of 86 patients with pulmonary TB were analyzed. The median time to sputum culture conversion was 39 days, and the maximum time was 116 days. The Cox proportional-hazards analysis showed that a higher smear grading (HR, 0.40; 95%CI, 0.23-0.71) and a history of ever smoking (HR, 0.48; 95%CI, 0.25-0.94) were associated with delayed sputum culture conversion. High smear grading and smoking prolonged the time to sputum culture conversion in adults with pulmonary TB. To effectively control TB, measures to decrease the cigarette smoking rate should be implemented, in addition to early detection and timely anti-TB treatment.

  11. Factors Affecting Time to Sputum Culture Conversion in Adults with Pulmonary Tuberculosis: A Historical Cohort Study without Censored Cases.

    Directory of Open Access Journals (Sweden)

    Rie Kanda

    Full Text Available In patients with pulmonary tuberculosis (TB, shortening the time to sputum culture conversion is desirable to reduce the likelihood of mycobacterial transmission. A persistent positive sputum culture after 2 months of treatment is reported to be associated with the presence of cavitation and the extent of disease on chest X-ray, high colony count, diabetes mellitus, and smoking. However, little is known about factors affecting the time to sputum culture conversion. This study was conducted to evaluate factors affecting the time to sputum culture conversion throughout the course of treatment in adults with pulmonary TB.This study was performed using a database of the medical records of patients with active pulmonary TB who were treated at Hirakata Kohsai Hospital in Hirakata City, Osaka, Japan, from October 2000 to October 2002. Cox proportional-hazards analysis was used to evaluate factors affecting the time to sputum culture conversion after adjusting for potential confounders.The data of 86 patients with pulmonary TB were analyzed. The median time to sputum culture conversion was 39 days, and the maximum time was 116 days. The Cox proportional-hazards analysis showed that a higher smear grading (HR, 0.40; 95%CI, 0.23-0.71 and a history of ever smoking (HR, 0.48; 95%CI, 0.25-0.94 were associated with delayed sputum culture conversion.High smear grading and smoking prolonged the time to sputum culture conversion in adults with pulmonary TB. To effectively control TB, measures to decrease the cigarette smoking rate should be implemented, in addition to early detection and timely anti-TB treatment.

  12. A feasibility assessment of calculation procedure with case study and the modification of dose conversion factor in STARDOSE

    International Nuclear Information System (INIS)

    Ko, H. S.; Jang, M.; Kim, S. H.; Kang, C. S.

    2003-01-01

    STARDOSE computer code is the designed code for which is calculated the dose of control room and off-site dose on design basis accident of nuclear power plant. Input files of STARDOSE are libfile1.txt which has decay constant and dose conversion factor, and input.dat which structurally expresses the real plant model by editor. It is given much advanced result with using newer dose conversion factor in libfile1.txt. In this study, therefore, case study is performed that is made input.dat file for LOCA and libfile1.txt which is included newer dose conversion factor and core inventory on APR-1400 and UCN 5 and 6. The result of case study is compared and analyzed

  13. Behaviour study of trace radioelements in the cycles of uranium conversion

    International Nuclear Information System (INIS)

    Bertaux, M.

    1998-01-01

    The aim of this work was to study the presence of ultra-trace radioelements in the cycles of uranium conversion. Radiochemical methods for determining ultra-trace amounts of various elements in uranium have been perfected. These methods are based on the chromatographic separation of anionic complexes and on the measurement of various activities by alpha spectrometry. Thus, the source of these traces has been determined and a work of tracing has been carried out in the Malvesi site (uranium purification unit). This work has revealed an accumulation of these traces in the uranium purification column, consequently to their extraction by the TBP. A decontamination process of weakly contaminated uranium batches has been proposed using the Parex computer model and tested at the industrial scale. This process is based on the U(VI) extraction by the TBP/ISOPAR mixture and on the use of oxalic acid as the complexing agent of the tetravalent actinides in aqueous phase. It has been tested with success during a purification study of a batch of about 4 tons of uranium contaminated by traces of various radioelements. The preliminary study had taken into account the influence of metallic impurities (iron, nickel, copper) on the radioelements complexation by the oxalate ions. (O.M.)

  14. Numerical Study of the Cascading Energy Conversion of the Reconnecting Current Sheet in Solar Eruptions

    Science.gov (United States)

    Ye, J.; Lin, J.; Raymond, J. C.; Shen, C.

    2017-12-01

    In this paper, we present a resistive magnetohydrodynamical study (2D) of the CME eruption based on the Lin & Forbes model (2000) regarding the cascading reconnection by a high-order Godunov scheme code, to better understand the physical mechanisms responsible for the internal structure of the current sheet (CS) and the high reconnection rate. The main improvements of this work include: 1) large enough spatial scale consistent with the stereo LASCO data that yields an observable current sheet 2) A realistic plasma environment (S&G, 1999) adopted rather than an isothermal atmosphere and higher resolution inside CS 3) The upper boundary condition set to be open. The simulation shows a typical acceleration below 2 R⊙, then its speed slightly fluctuated, and the flux rope velocity is estimated to be 100 km/s-250 km/s for a slow CME. The reconnection rates are around 0.02 estimated from inflow and outflow velocities. The dynamic features show a great consistence with the LASCO observations. Looking into the fine structure of CS, magnetic reconnection initializes with a Sweet-Parker stage, and undergoes the time-dependent Petschek/fractural patterns. While the CME continues climbing up, the outflow region becomes turbulent which enhances the reconnection rates furthermore. The local reconnection rates present a simple linear dependence with the length-width ratio of multiple small-scale CSs. The principal X-point is close to the Sun's surface during the entire eruption, causing the energy partition to be unequal. Energy conversion in the vicinity of the principal X-point has also been addressed by simply employing energy equations. And we demonstrate that the dominant energy transfer consists of a conversion of the incoming Poynting flux to enthalpy flux in the sunward direction and bulk kinetic energy in the CME direction. The spectrum of magnetic energy doesn't follow a simple power law after secondary islands appear, and the spectrum index varies from 1.5 to 2

  15. Numerical study of the particle transport in fast neutron detectors with conversion layer

    International Nuclear Information System (INIS)

    Sedlackova, K.; Zatko, B.; Necas, V.

    2012-01-01

    This paper deals with fast neutron and recoil proton transport simulation using statistical analysis of Monte Carlo radiation transport code (MCNPX). Its possibilities in the detector design and optimization are presented. MCNPX proved as a very advantageous self-contained simulation program for fast neutron and secondary proton tracking. Simulations of respective particle transport through conversion layer of HDPE and further in the active volume of detector let us to follow important characteristics as neutron/proton flux density, reaction rate of elastic scattering on hydrogen nuclei and deposited energy as well as their dependencies on incident neutron energy and conversion layer/active region thickness. The efficiency of neutrons to protons conversion has been calculated and its maximum was reached for 500 μm thick conversion layer. The minimum active region thickness has been estimated to be about 300 μm.(authors)

  16. [Dissociation (conversion) - malingering - antisocial personality disorder: differential diagnostic reflection on the basis of a case study].

    Science.gov (United States)

    Rothuber, Helfried; Mitterauer, Bernhard

    2011-01-01

    In this case report we refer to the big challenge of making a diagnosis in a deliberate malingering in the field of mental disorders. We specifically describe the difficulty regarding the differentiation between a conversion disorder and malingering of a serial delinquent. For such a person avoiding criminal persecution is one of the most frequent reason to deceitfully simulate a mental illness. In this field, symptoms of conversion disorders exceed the average; furthermore, a great number of organic-neurological illnesses may appear to be very similar to a conversion disorder or in many cases a neurological disorder can actually be detected in the course of a somatic examination. A further obstacle for the differential diagnosis can be seen in the difficulty to discern it from factitious disorders. However, it is quite possible to discern the deliberate malingering of a mental disorder from a conversion disorder by means of the diligent diagnosis of a competent and experienced doctor/assessor who specialises.

  17. Supplementary study about the ATC generic project. Alternative storage for encapsulated fuel

    International Nuclear Information System (INIS)

    Canadas Martinez, I.

    2010-01-01

    The objective of this study is to present the alternatives for a complementary installation and facilitate the decision making on the best solution, keeping many determining factors in mind. Two are the alternatives studied: supplementary storage, similar to the Trillo Nuclear Power Plant, and outdoor storage, similar to the Asco and Jose Cabrera Nuclear Power Plants.

  18. Design study on evaluation for power conversion system concepts in high temperature gas cooled reactor with gas turbine

    International Nuclear Information System (INIS)

    Minatsuki, Isao; Mizokami, Yorikata

    2007-01-01

    The design studies on High Temperature Gas Cooled Reactor with Gas Turbine (HTGR-GT) have been performed, which were mainly promoted by Japan Atomic Energy Agency (JAEA) and supported by fabricators in Japan. HTGR-GT plant feature is almost determined by selection of power conversion system concepts. Therefore, plant design philosophy is observed characteristically in selection of them. This paper describes the evaluation and analysis of the essential concepts of the HTGR-GT power conversion system through the investigations based on our experiences and engineering knowledge as a fabricator. As a result, the following concepts were evaluated that have advantages against other competitive one, such as the horizontal turbo machine rotor, the turbo machine in an individual vessel, the turbo machine with single shaft, the generator inside the power conversion vessel, and the power conversion system cycle with an intercooler. The results of the study can contribute as reference data when the concepts will be selected. Furthermore, we addressed reasonableness about the concept selection of the Gas Turbine High Temperature Reactor GTHTR300 power conversion system, which has been promoted by JAEA. As a conclusion, we recognized the GTHTR300 would be one of the most promising concepts for commercialization in near future. (author)

  19. Study for engine conversion from gasoline to natural gas by using the two-zone combustion predictive model; Estudio de la conversion del motor de gasolina a gas natural mediante modelo de combustion predictivo de dos zonas

    Energy Technology Data Exchange (ETDEWEB)

    Henry, Espinoza; Moreno, Jesus; Perez, Andres [Universidad de Oriente, Puerto la Cruz (Venezuela). Dept. de Mecanica; Baduy, Franklin [Universidad Central de Venezuela, Caracas (Venezuela). Dept. de Termoenergetica

    1995-07-01

    Great scale conversion of automation engines is a policy used by many countries as a strategy to save gasoline. Previous studies on the effects that this transformation can have over the engine performance are required for the implantation of this type of conversion. also, modifications in components and tuning for each engine have to be analyzed. This paper studies the effect of the conversion from gasoline to natural gas over the engine output, indicate mean pressure, combustion rate etc. It also analyze how to find the starting angle and the best air/fuel ratio for a specific engine, using a two-zone combustion model. (author)

  20. Environmental studies related to the operation of wind energy conversion systems. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, S.E.; Cornaby, B.W.; Rodman, C.W.; Sticksel, P.R.; Tolle, D.A.

    1977-12-01

    This biophysical impact assessment explores the environmental consequences of the emerging wind energy conversion technology through field studies done at the DOE/NASA 100-kW Experimental Wind Turbine located at NASA Lewis Research Center's Plum Brook Station near Sandusky, Ohio. A micrometeorological field program monitored changes in the downwind wake of the wind turbine. Horizontal and/or vertical measurements of wind speed, temperature, carbon dioxide concentration, precipitation, and incident solar radiation showed measurable variation within the wake only for precipitation and wind speed. The changes were minor and not likely to result in any secondary effects to vegetation, including crops, because they are within the natural range of variability in the site environment. Effects are negligible beyond the physically altered area of the tower pad, access, and control structures. The wind turbine has not proved to be a high risk to airborne fauna, including the most vulnerable night-migrating songbirds. Behavioral studies indicate the birds will avoid the turbine if they can see it.

  1. Economic Assessment of Overtopping BReakwater for Energy Conversion (OBREC: A Case Study in Western Australia

    Directory of Open Access Journals (Sweden)

    Pasquale Contestabile

    2016-12-01

    Full Text Available This paper constructs an optimal configuration assessment, in terms of the financial returns, of the Overtopping BReakwater for wave Energy Conversion (OBREC. This technology represents a hybrid wave energy harvester, totally embedded in traditional rubble mound breakwaters. Nine case studies along the southern coast of Western Australia have been analysed. The technique provides tips on how to estimate the quality of the investments, for benchmarking with different turbine strategy layouts and overlapping with the costs of traditional rubble mound breakwaters. Analyses of the offshore and nearshore wave climate have been studied by a high resolution coastal propagation model, forced with wave data from the European Centre for Medium-Range Weather Forecasts (ECMWF. Inshore wave conditions have been used to quantify the exploitable resources. It has been demonstrated that the optimal investment strategy is nonlinearly dependent on potential electricity production due to outer technical constraints. The work emphasizes the importance of integrating energy production predictions in an economic decision framework for prioritizing adaptation investments.

  2. Study on potency of municipal solid waste conversion into renewable energy by thermal incineration and bioconversion: case study of Medan city

    Science.gov (United States)

    Sarah, Maya; Misran, Erni

    2018-03-01

    Municipal solid waste (MSW) in Medan City is facing problems either with the quantity and management of MSW. Local authority only dumped approximately 73.9% MSW in the landfill over the years. Spontaneous phenomena of methane formation in dumping site indicates the potency of MSW conversion into energy by biochemical conversion. On the contrary, the presence of plastics, woods, papers, etc. in the MSW show the potency of MSW to be treated by thermal conversion. Both thermal incineration and anaerobic digestion may convert MSW Medan City into energy. This study evaluates potency of MSW conversion into renewable energy using proximate and ultimate analysis. Overall, MSW of Medan City has the opportunities to be converted into energy by both thermal and biochemical conversion with a special requirement such as pre-dry the MSW prior incineration process and degrade organic MSW in a bioreactor.

  3. Conversion electron spectroscopy at the FMA focal plane: Decay studies of proton-rich N {approximately} 82 nuclei

    Energy Technology Data Exchange (ETDEWEB)

    Nisius, D.; Janssens, R.V.F.; Ahmad, I. [and others

    1995-08-01

    The FMA has proven to be an ideal instrument for the detailed study of the decay of microsecond isomers behind the focal plane following mass selection. In reactions leading to the population of nuclei with isomeric lifetimes longer than their flight time through the device, decay gamma rays and conversion electrons can be detected in an environment free from the backgrounds of prompt radiation and delta electrons. This was a very successful technique to study proton (h{sub 11/2}){sup n} seniority isomers in nuclei with Z > 64 and N {approximately} 82. Since isomeric decay gamma rays are emitted isotropically, conversion electrons are essential for the assignment of multipolarities in these nuclei. Furthermore, the low-energy transitions that depopulate isomeric states are typically highly converted and can escape gamma-ray detection, but they can be identified by their conversion electrons.

  4. Study of parameters affecting the conversion in a plug flow reactor for reactions of the type 2A→B

    Science.gov (United States)

    Beltran-Prieto, Juan Carlos; Long, Nguyen Huynh Bach Son

    2018-04-01

    Modeling of chemical reactors is an important tool to quantify reagent conversion, product yield and selectivity towards a specific compound and to describe the behavior of the system. Proposal of differential equations describing the mass and energy balance are among the most important steps required during the modeling process as they play a special role in the design and operation of the reactor. Parameters governing transfer of heat and mass have a strong relevance in the rate of the reaction. Understanding this information is important for the selection of reactor and operating regime. In this paper we studied the irreversible gas-phase reaction 2A→B. We model the conversion that can be achieved as function of the reactor volume and feeding temperature. Additionally, we discuss the effect of activation energy and the heat of reaction on the conversion achieved in the tubular reactor. Furthermore, we considered that dimerization occurs instantaneously in the catalytic surface to develop equations for the determination of rate of reaction per unit area of three different catalytic surface shapes. This data can be combined with information about the global rate of conversion in the reactor to improve regent conversion and yield of product.

  5. Studies on the products resulting from the conversion of aspen poplar to an oil

    Energy Technology Data Exchange (ETDEWEB)

    Eager, R L; Mathews, J F; Pepper, J M; Zohdi, H

    1981-01-01

    The reactions involved in the conversion of aspen poplar into a variety of chemical products as a result of its interaction with CO and H/sub 2/O in the presence of Na/sub 2/CO/sub 3/ at elevated temperatures and pressures are considered. The original C content of the wood is distributed between an oil phase, a complex mixture of highly oxygenated H/sub 2/O-soluble products many of which were identified as low-molecular-weight aliphatic alcohols, ketones, and acids, and a gaseous phase consisting of mainly H and CO/sub 2/. Using model substances (cellulose, cellobiose, -D-glucose, D-fructose, D-xylose, sorbitol, glycerol, and an isolated lignin) information was obtained on the origin of the oil and of the H/sub 2/O-soluble products. Studies at 160 degrees - 360 degrees revealed a marked exothermic reaction occurring at 200-240 degrees for wood and cellulose, which was reflected in the nature of the resulting product. With increasing temperature an increase in the yields of the H/sub 2/O-souluble derivatives and also a change in their relative abundance was observed.

  6. Electrochemical and conversion electron Moessbauer study of corrosion induced by acid rain

    International Nuclear Information System (INIS)

    Vertes, C.; Lakatos-Varsanyi, M.; Vertes, A.; Meisel, W.; Guetlich, P.

    1993-01-01

    The passivation of low carbon steel was studied in aqueous solution of 0.5M Na 2 SO 4 +0.001M NaHSO 3 (pH 3.5, 6.5 and 8.5) which can be considered as a model of acid rain. The used conversion electron Moessbauer spectroscopy (CEMS) with the complementary electrochemical investigations proved that the sulfite ions induce pitting corrosion at pH 3.5 and 6.5, while the measurements showed much weaker pitting at pH 8.5. The compositions and thicknesses of the passive films formed during the electrochemical treatments are determined from the CEM spectra. Only γ-FeOOH was found on the surface of the samples at pH 6.5 and 8.5. Nevertheless, at pH 3.5 the sextet belonging to Fe 3 C appears in the spectra, and also FeSO 4 .H 2 O could be detected in low concentration. (orig.)

  7. Alternative policy study. Environment and energy in Europe and Central Asia 1990-2010. Energy-related environmental impacts of policy scenarios. GEO 2000 alternative policy study

    International Nuclear Information System (INIS)

    Van Vuuren, D.P.; Bakkes, J.A.

    2000-01-01

    The GEO-2000 study into alternative policy options for Europe and Central Asia focuses on energy use as an important driver for environmental problems across the region. The problems analyzed are climate change, acidification, summer smog, urban air pollution and risks of reactor accidents associated with nuclear power generation. The analysis includes the effects on biodiversity and population health. It considers the question of what can be achieved by moderate measures, and whether this will be enough. Similar Geo-2000 region-specific studies on alternative policies have been compiled other world regions. This report outliners the general methodology for these reports

  8. Microwave-assisted solid phase conversion study of Meldrum's acid to ethylenetetracarboxylic dianhydride (C 6O 6)

    Science.gov (United States)

    Taherpour, Avat (Arman)

    2010-01-01

    Utilization of microwave irradiation provides an effective method for fast synthesizing of some important compounds. Microwave-assisted solid phase is an especial class in chemical synthesis. By the use of MW-irradiation on chemicals, sometimes interesting results can be seen. The synthesis of the interesting molecule ethylenetetracarboxylic dianhydride (C 6O 6) was attempted with a few different methods. In this study, the microwave-assisted solid phase conversion of Meldrum's acid to ethylenetetracarboxylic dianhydride was reported. This conversion was characterized by FT-IR, GC/MS and NMR spectroscopy results.

  9. Can Alternative Education Increase Children's Early School Engagement? A Longitudinal Study from Kindergarten to Third Grade

    Science.gov (United States)

    de Bilde, Jerissa; Van Damme, Jan; Lamote, Carl; De Fraine, Bieke

    2013-01-01

    The current study examines the impact of alternative education on children's early school engagement in terms of school enjoyment and independent participation. A sample of 2,776 children from traditional (e.g., mainstream) and alternative (Freinet and Waldorf) Flemish schools was followed from their 3rd year of kindergarten until 3rd grade. The…

  10. Generating alternative alignments in terrain suitability studies for environmental impact assessments of linear developments

    CSIR Research Space (South Africa)

    Van Deventer, Heidi

    2010-08-01

    Full Text Available (EIA). Though legislation requires a screening or scoping of alternative options prior to the EIA, the use of Geographical Information Systems (GIS) is seldom used in generating alternatives through a Terrain Suitability Study (TSS). The inclusion of a...

  11. Study of Effective Alternative Education Programs: Final Grant Report

    Science.gov (United States)

    Quinn, Mary Magee; Poirier, Jeffrey M.

    2007-01-01

    This report presents findings of a study conducted to identify the components of systems that effectively meet the diverse, ever changing needs of children with disabilities for whom traditional school settings do not work. A secondary goal of this study was to develop a conceptually clear and empirically grounded definition of alternative…

  12. Quantifying the uncertainty of wave energy conversion device cost for policy appraisal: An Irish case study

    International Nuclear Information System (INIS)

    Farrell, Niall; Donoghue, Cathal O’; Morrissey, Karyn

    2015-01-01

    Wave Energy Conversion (WEC) devices are at a pre-commercial stage of development with feasibility studies sensitive to uncertainties surrounding assumed input costs. This may affect decision making. This paper analyses the impact these uncertainties may have on investor, developer and policymaker decisions using an Irish case study. Calibrated to data present in the literature, a probabilistic methodology is shown to be an effective means to carry this out. Value at Risk (VaR) and Conditional Value at Risk (CVaR) metrics are used to quantify the certainty of achieving a given cost or return on investment. We analyse the certainty of financial return provided by the proposed Irish Feed-in Tariff (FiT) policy. The influence of cost reduction through bulk discount is also discussed, with cost reduction targets for developers identified. Uncertainty is found to have a greater impact on the profitability of smaller installations and those subject to lower rates of cost reduction. This paper emphasises that a premium is required to account for cost uncertainty when setting FiT rates. By quantifying uncertainty, a means to specify an efficient premium is presented. - Highlights: • Probabilistic model quantifies uncertainty for wave energy feasibility analyses. • Methodology presented and applied to an Irish case study. • A feed-in tariff premium of 3–4 c/kWh required to account for cost uncertainty. • Sensitivity of uncertainty and cost to rates of technological change analysed. • Use of probabilistic model for investors and developers also demonstrated

  13. Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 10: Liquid-metal MHD systems. [energy conversion efficiency of electric power plants using liquid metal magnetohydrodynamics

    Science.gov (United States)

    Holman, R. R.; Lippert, T. E.

    1976-01-01

    Electric Power Plant costs and efficiencies are presented for two basic liquid-metal cycles corresponding to 922 and 1089 K (1200 and 1500 F) for a commercial applications using direct coal firing. Sixteen plant designs are considered for which major component equipment were sized and costed. The design basis for each major component is discussed. Also described is the overall systems computer model that was developed to analyze the thermodynamics of the various cycle configurations that were considered.

  14. Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 8: Open-cycle MHD. [energy conversion efficiency and design analysis of electric power plants employing magnetohydrodynamics

    Science.gov (United States)

    Hoover, D. Q.

    1976-01-01

    Electric power plant costs and efficiencies are presented for three basic open-cycle MHD systems: (1) direct coal fired system, (2) a system with a separately fired air heater, and (3) a system burning low-Btu gas from an integrated gasifier. Power plant designs were developed corresponding to the basic cases with variation of major parameters for which major system components were sized and costed. Flow diagrams describing each design are presented. A discussion of the limitations of each design is made within the framework of the assumptions made.

  15. Study on film resistivity of Energy Conversion Components for MEMS Initiating Explosive Device

    Science.gov (United States)

    Ren, Wei; Zhang, Bin; Zhao, Yulong; Chu, Enyi; Yin, Ming; Li, Hui; Wang, Kexuan

    2018-03-01

    Resistivity of Plane-film Energy Conversion Components is a key parameter to influence its resistance and explosive performance, and also it has important relations with the preparation of thin film technology, scale, structure and etc. In order to improve the design of Energy Conversion Components for MEMS Initiating Explosive Device, and reduce the design deviation of Energy Conversion Components in microscale, guarantee the design resistance and ignition performance of MEMS Initiating Explosive Device, this paper theoretically analyzed the influence factors of film resistivity in microscale, through the preparation of Al film and Ni-Cr film at different thickness with micro/nano, then obtain the film resistivity parameter of the typical metal under different thickness, and reveals the effect rule of the scale to the resistivity in microscale, at the same time we obtain the corresponding inflection point data.

  16. SYNTHESIS, THERMAL STUDIES AND CONVERSION DEGREE OF DIMETHACRYLATE POLYMERS USING NEW NON-TOXIC COINITIATORS

    Directory of Open Access Journals (Sweden)

    Rafael Turra Alarcon

    Full Text Available The aim of this paper is to replace toxic coinitiators (tertiary amines by non-toxic compounds such as glycerol and inositol (polyalcohol in dimethacrylate resins. For this purpose, mid infrared spectroscopy (MIR was used to calculate the monomers' degree of conversion (%DC; as well as simultaneous Thermogravimetric Analysis – Differential Thermal Analysis (TGA-DTA and Differential Scanning Calorimetry (DSC were conducted to evaluate thermal stability, degradation steps, and thermal events. The use of different initiator systems did not modify the thermal events or the thermal stability of each of the dimethacrylate resins. Results show a substitution of system 2 (toxicity by system 3 (low toxicity, which had a good conversion velocity and total conversion in some monomers, is plausible.

  17. Study on Conversion Between Momentum and Contrarian Based on Fractal Game

    Science.gov (United States)

    Wu, Xu; Song, Guanghui; Deng, Yan; Xu, Lin

    2015-06-01

    Based on the fractal game which is performed by the majority and the minority, the fractal market theory (FMT) is employed to describe the features of investors' decision-making. Accordingly, the process of fractal games is formed in order to analyze the statistical features of conversion between momentum and contrarian. The result shows that among three fractal game mechanisms, the statistical feature of simulated return rate series is much more similar to log returns on actual series. In addition, the conversion between momentum and contrarian is also extremely similar to real situation, which can reflect the effectiveness of using fractal game in analyzing the conversion between momentum and contrarian. Moreover, it also provides decision-making reference which helps investors develop effective investment strategy.

  18. Design study of eventual core conversion for the research reactor RA

    International Nuclear Information System (INIS)

    Matausek, M. V.; Marinkovic, N.

    1998-01-01

    Main options are specified for the future status of the 6.5 MW heavy water research reactor RA. Arguments pro and contra restarting the reactor are presented. When considering the option to restart the RA reactor, possibilities to improve its neutronic parameters, such as neutron flux values and irradiation capabilities are discussed, as well as the compliance with the worldwide activities of Reduced Enrichment for Research and Test Reactors (RERTR) program. Possibility of core conversion is examined. Detailed reactor physics design calculations are performed for different fuel types and uranium loading. For different fuel management schemes results are presented for the effective, multiplication factor, power distribution, fuel burnup and consumption. It is shown that, as far as reactor core parameters are considered, conversion to lower enrichment fuel could be easily accomplished. However, conversion to the lower enrichment could only be justified if combined with improvement of some other reactor attributes. (author)

  19. Potentials of the separation of cow manure. Utilization of solid materials as an alternative fermentation substrate in biogas conversion plants; Potentiale der Rinderguelleseparation. Nutzung der Feststoffe als alternatives Gaersubstrat in Biogasanlagen

    Energy Technology Data Exchange (ETDEWEB)

    Kroeger, Rhena; Hothan, Andreas; Theuvsen, Ludwig; Broll, Gabriele; Brauckmann, Hans-Joerg; Bronsema, Hauke [Goettingen Univ. (Germany). Dept. fuer Agraroekonomie und Rurale Entwicklung, Betriebswirtschaftslehre des Agribusiness

    2013-10-01

    The increasing regional concentration of dairy farming requires alternatives for the use of the accruing slurry to defuse the nutrient problem. One possibility is to separate the manure and use the solid fraction for an energetic use in biogas plants in nutrient undersupplied regions. First practical tests on dairy slurry separation have shown that separators are able to achieve a performance 1.3 to 16.6 tons of mass flow per hour. The nutrients are disproportionately deposited in the solid fraction. Furthermore, the solid fractions show a methane building potential that is double as high as the raw slurry methane yield. An energetic use of the solid fraction allows the reduction of other substrates. Thus, it is possible to decrease the land requirements and the costs for other substrates. (orig.)

  20. Adherence to tuberculosis treatment, sputum smear conversion and mortality: a retrospective cohort study in 48 rwandan clinics

    NARCIS (Netherlands)

    Kayigamba, Felix R.; Bakker, Mirjam I.; Mugisha, Veronicah; de Naeyer, Ludwig; Gasana, Michel; Cobelens, Frank; Schim van der Loeff, Maarten

    2013-01-01

    Adherence to treatment and sputum smear conversion after 2 months of treatment are thought to be important for successful outcome of tuberculosis (TB) treatment. Retrospective cohort study of new adult TB patients diagnosed in the first quarter of 2007 at 48 clinics in Rwanda. Data were abstracted

  1. Parametric study of up-conversion efficiency in Er-doped ceria nanoparticles under 780 nm excitation

    International Nuclear Information System (INIS)

    Shehata, N.; Kandas, I.; Samir, E.; Meehan, K.; Aldacher, M.

    2016-01-01

    This paper presents a new parametric study of the optical up-conversion process in ceria nanoparticles doped with erbium (Er-CeO 2 NPs). Under 780 nm excitation, both the possible transitions that occur between Er 3+ ions and up-conversion rate model simulation are presented. Ceria nanoparticles (CeO 2 NPs) doped with erbium are experimentally synthesized using chemical precipitation technique with post-annealing up to 900 °C with different weight ratios of erbium dopant. We found that the synthesized nanoparticles can emit both green and red emissions under 780 nm laser excitation via two-photon absorption mechanism. Then, the quantum efficiencies of both colored emissions are theoretically investigated with different parameters related to the optical conversion process and the studied material. In addition, this work offer suggested ranges for the optimum values of the studied parameters which could improve the quantum yield efficiency. Einstein coefficients for erbium hosted in ceria are discussed in details using Judd–Ofelt analysis. This promising study could be helpful in improving the up-conversion efficiency of Er-ceria nanoparticles for applications such as bio-imaging and optical-based sensors.

  2. Downwards Vertical Attention Bias in Conversion Disorder vs Controls: A Pilot Study.

    Science.gov (United States)

    Gazit, Sivan; Elkana, Odelia; Dawidowicz, Liraz; Yeshayahu, Liel; Biran, Iftah

    Conversion disorder (CD) is a largely enigmatic disorder, one that requires a thorough ruling-out process. Prior research suggests that metaphors and conceptualization are rooted in physical experience, and that we interpret our affective world through metaphors. Spatial metaphors (interaction of affect and vertical space) are a prominent example of the grounding of metaphors. This is a relatively unpaved direction of research of CD. The present pilot study sought to explore this view by investigating the "healthy is up, sick is down" spatial metaphors (e.g., "fell ill" and "top shape") in patients with CD, examining the correlation between the processing of bodily-related words, CD, and vertical space. We hypothesized that patients with CD, who experience their bodies as ill, will demonstrate a downwards bias when processing bodily-related words; corresponding to the "healthy is up, sick is down" spatial metaphor. A total of 8 female patients (ages M-38.13 SD-10.44) and 42 female controls (ages M-36.4 SD-14.57) performed a visual attention task. Participants were asked to identify a spatial probe at the top or the bottom of a screen, following either a bodily related (e.g., arm) or non-bodily related (e.g., clock) prime word. As predicted, when processing bodily-related words, patients with CD demonstrated a downwards attention bias. Moreover, the higher the patient's level of somatization, the faster the patient detected lower (vs upper) spatial targets. This study suggests that the changed health paradigm of patients with CD is grounded in sensorimotor perception. Further research could propose new diagnostic and treatment options for CD. Copyright © 2017 The Academy of Psychosomatic Medicine. Published by Elsevier Inc. All rights reserved.

  3. Study on thermal electric conversion system for FBR plant. Investigation for effective EVST waste heat recovery system

    International Nuclear Information System (INIS)

    Maekawa, Isamu; Kurata, Chikatoshi

    2004-02-01

    Recently, it has been important to reuse discharged heat energy from present nuclear plant, especially from sodium cooled FBR, which are typical high temperature system, in the view of reduction of environmental burden and improvement of heat efficiency for plant. The thermal electric conversion system can work only the temperature difference and has been applied to the limited fields such as space or military, however, that results show good merits for reliability, maintenance free, and so on. Recently, the development of new thermal electric conversion elements has made remarkable progress. In this study, for the effective utilization of waste heat from Monju', the prototype plant of FBR, we made an investigation of electric power generating system maintaining the cooling faculty by applying the thermal electric conversion system to sodium cooling line of EVST. Using the new type iron based thermal electric conversion elements, which are plentiful, economical and good for environmental harmonization, we have calculated the amount of heat exchange and power generation from sodium cooling line of EVST, and have investigated the module sizing, cost and subject to be settled. The results were , (1)The amount of power generation from sodium cooling line of EVST is smaller about one figure than motive power of sodium cooler fan. However, if Seebeck coefficient and heat conductivity of iron based thermal electric conversion elements shall be improved, power from sodium cooling line shall be able to cover the motive power. (2) The amount of heat released from sodium cooling line after the installation of thermal electric conversion module covers the necessity to maintain the sodium cooling faculty. (3) In case of the installation of module to the sodium cooler, it should be reconstructed because of tube arrangement modification. In case of the installation of module to the sodium connecting line, air ventilation system is needed to suppress the room temperature. (4) As

  4. Efficacy study of the digital image processing with varying pixel size at A/D conversion of the chest radiograph

    Energy Technology Data Exchange (ETDEWEB)

    Inamoto, Kazuo; Tanaka, Shinichi; Miura, Takashi; Takahashi, Akira; Iwata, Tetsuya

    1984-12-01

    In the study for development of medical image archiving system, we made experiments in the field of conversion of a X-ray picture to a digital form. Three sets of chest radiograph were selected for the study of digitalization by reading different pixel size (150-300 m) in the method of A/D conversion using a drum scanner and again reconstructed to an analog form after D/A conversion. These copy films of different pixel size were shown and evaluated by 48 volunteer doctors to choose a favorite picture. It did not always follow that the most favorite picture was the finest one using the smallest pixel size. This discrepancy was further analyzed by measurement of a density histogram. By comparison studies of density curves in the same ROI of different pixel size pictures, it was concluded that their choices were dependent on not only fineness but also contrast of an output image after D/A conversion. Often better contrast picture was a key to the selection more than the pixel size. This indicates that digital storing radiographs will be possibly regenerated to the real image by the skillful operation of pixel size and contrast of a radiograph. The results will contribute to the process of recording analog X-ray picture by a digital form in the medical image archiving system.

  5. Effective dose per unit kerma-area product conversion factors in adults undergoing modified barium swallow studies

    International Nuclear Information System (INIS)

    Shaw Bonilha, Heather; Wilmskoetter, Janina; Tipnis, Sameer V.; Martin-Harris, Bonnie; Huda, Walter

    2017-01-01

    This study presents an investigation of adult effective dose (E) per unit Kerma-Area Product (KAP) in Modified Barium Swallow Study (MBSS) examinations. PC program for X-ray Monte Carlo (version 2.0.1) was used to calculate patient organ doses during MBSS examinations, which used combined to generate effective dose. Normalized patient doses were obtained by dividing the effective dose (mSv) by the incident KAP (Gy.cm 2 ). Five standard projections were studied and the importance of X-ray beam size and in patient size (body mass index) were investigated. Lateral projections had an average E/ KAP conversion factor of 0.19 ± 0.04 mSv/Gy.cm 2 . The average E/KAP was highest for upper gastrointestinal (GI) anterior- posterior projections (0.27 ± 0.04 mSv/Gy.cm 2 ) and lowest for upper GI posterior-anterior projections (0.09 ± 0.03 mSv/ Gy.cm 2 ). E/KAP always increased with increasing filtration and/or X-ray tube voltage. Reducing the X-ray beam cross-sectional area increased the E/KAP conversion factors. Small patients have the E/KAP conversion factors that are twice those of a standard adult. Conversion factors for effective dose of adult patients undergoing MBSS examinations must account for X-ray beam projection, beam quality (kV and filtration), image size and patient size. (authors)

  6. Alternative Policy Study: Environment and energy in Europe and Central Asia 1990-2010. Energy-related environmental impacts of policy scenarios GEO-2000 alternative policy study

    NARCIS (Netherlands)

    Vuuren DP van; Bakkes JA; United Nations Environment; MNV

    2000-01-01

    The GEO-2000 study into alternative policy options for Europe and Central Asia focuses on energy use as an important driver for environmental problems across the region. The problems analyzed are climate change, acidification, summer smog, urban air pollution and risks of reactor accidents

  7. Comparative study of Waste Isolation Pilot Plant (WIPP) transportation alternatives

    International Nuclear Information System (INIS)

    1994-02-01

    WIPP transportation studies in the Final Supplement Environmental Impact Statement for WIPP are the baseline for this report. In an attempt to present the most current analysis, this study incorporates the most relevant data available. The following three transportation options are evaluated for the Disposal Phase, which is assumed to be 20 years: Truck shipments, consisting of a tractor and trailer, with three TRUPACT-IIs or one RH-72B; Regular commercial train shipments consisting of up to three railcars carrying up to 18 TRUPACT-IIs or up to six RH-72Bs; Dedicated train shipments consisting of a locomotive, an idle car, railcars carrying 18 TRUPACT-IIs or six RH-72Bs, another idle car, and a caboose or passenger car with an emergency response specialist. No other cargo is carried. This report includes: A consideration of occupational and public risks and exposures, and other environmental impacts; A consideration of emergency response capabilities; and An extimation of comparative costs

  8. Comparative study of Waste Isolation Pilot Plant (WIPP) transportation alternatives

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    WIPP transportation studies in the Final Supplement Environmental Impact Statement for WIPP are the baseline for this report. In an attempt to present the most current analysis, this study incorporates the most relevant data available. The following three transportation options are evaluated for the Disposal Phase, which is assumed to be 20 years: Truck shipments, consisting of a tractor and trailer, with three TRUPACT-IIs or one RH-72B; Regular commercial train shipments consisting of up to three railcars carrying up to 18 TRUPACT-IIs or up to six RH-72Bs; Dedicated train shipments consisting of a locomotive, an idle car, railcars carrying 18 TRUPACT-IIs or six RH-72Bs, another idle car, and a caboose or passenger car with an emergency response specialist. No other cargo is carried. This report includes: A consideration of occupational and public risks and exposures, and other environmental impacts; A consideration of emergency response capabilities; and An extimation of comparative costs.

  9. Study on storage energy devices: supercapacitors, a green alternative

    OpenAIRE

    Rancaño Fernandez, Ariadna

    2011-01-01

    Nowadays, it is increasingly common to hear about environmental issues. This fact keep us to continually try to improve energy optimization, either through new storage devices that pollute less or improvements in the environmental energy generation systems. Recent new types of devices under study are those called supercapacitors. Supercapacitors are electronic devices able to store charge in form of electrical energy. This energy is stored as an electric field, so supercapacitors are less pol...

  10. A search for space energy alternatives

    Science.gov (United States)

    Gilbreath, W. P.; Billman, K. W.

    1978-01-01

    This paper takes a look at a number of schemes for converting radiant energy in space to useful energy for man. These schemes are possible alternatives to the currently most studied solar power satellite concept. Possible primary collection and conversion devices discussed include the space particle flux devices, solar windmills, photovoltaic devices, photochemical cells, photoemissive converters, heat engines, dielectric energy conversion, electrostatic generators, plasma solar collectors, and thermionic schemes. Transmission devices reviewed include lasers and masers.

  11. Numerical study of canister filters with alternatives filter cap configurations

    Science.gov (United States)

    Mohammed, A. N.; Daud, A. R.; Abdullah, K.; Seri, S. M.; Razali, M. A.; Hushim, M. F.; Khalid, A.

    2017-09-01

    Air filtration system and filter play an important role in getting a good quality air into turbo machinery such as gas turbine. The filtration system and filter has improved the quality of air and protect the gas turbine part from contaminants which could bring damage. During separation of contaminants from the air, pressure drop cannot be avoided but it can be minimized thus helps to reduce the intake losses of the engine [1]. This study is focused on the configuration of the filter in order to obtain the minimal pressure drop along the filter. The configuration used is the basic filter geometry provided by Salutary Avenue Manufacturing Sdn Bhd. and two modified canister filter cap which is designed based on the basic filter model. The geometries of the filter are generated by using SOLIDWORKS software and Computational Fluid Dynamics (CFD) software is used to analyse and simulates the flow through the filter. In this study, the parameters of the inlet velocity are 0.032 m/s, 0.063 m/s, 0.094 m/s and 0.126 m/s. The total pressure drop produce by basic, modified filter 1 and 2 is 292.3 Pa, 251.11 Pa and 274.7 Pa. The pressure drop reduction for the modified filter 1 is 41.19 Pa and 14.1% lower compared to basic filter and the pressure drop reduction for modified filter 2 is 17.6 Pa and 6.02% lower compared to the basic filter. The pressure drops for the basic filter are slightly different with the Salutary Avenue filter due to limited data and experiment details. CFD software are very reliable in running a simulation rather than produces the prototypes and conduct the experiment thus reducing overall time and cost in this study.

  12. Study on Millimeter-Wave Vivaldi Rectenna and Arrays with High Conversion Efficiency

    Directory of Open Access Journals (Sweden)

    Guan-Nan Tan

    2016-01-01

    Full Text Available A novel Vivaldi rectenna operated at 35 GHz with high millimeter wave to direct current (MMW-to-DC conversion efficiency is presented and the arrays are investigated. The measured conversion efficiency is 51.6% at 35 GHz and the efficiency higher than 30% is from 33.2 GHz to 36.6 GHz when the input MMW power is 79.4 mW. The receiving Vivaldi antenna loaded with metamaterial units has a high gain of 10.4 dBi at 35 GHz. A SIW- (substrate integrated waveguide- to-microstrip transition is designed not only to integrate the antenna with the rectifying circuit directly but also to provide the DC bypass for the rectifying circuit. When the power density is 8.7 mW/cm2, the received MMW power of the antenna is 5.6 mW, and the maximum conversion efficiency of the rectenna element is 31.5%. The output DC voltage of the element is nearly the same as that of the parallel array and is about half of the series array. The DC power obtained by the 1 × 2 rectenna arrays is about two times as much as that of the element. The conversion efficiencies of the arrays are very close to that of the element. Large scale arrays could be expended for collecting more DC power.

  13. Theoretical studies of thermionic conversion of solar energy with graphene as emitter and collector

    Science.gov (United States)

    Olawole, Olukunle C.; De, Dilip Kumar

    2018-01-01

    Thermionic energy conversion (TEC) using nanomaterials is an emerging field of research. It is known that graphene can withstand temperatures as high as 4600 K in vacuum, and it has been shown that its work function can be engineered from a high value (for monolayer/bilayer) of 4.6 eV to as low as 0.7 eV. Such attractive electronic properties (e.g., good electrical conductivity and high dielectric constant) make engineered graphene a good candidate as an emitter and collector in a thermionic energy converter for harnessing solar energy efficiently. We have used a modified Richardson-Dushman equation and have adopted a model where the collector temperature could be controlled through heat extraction in a calculated amount and a magnet can be attached on the back surface of the collector for future control of the space-charge effect. Our work shows that the efficiency of solar energy conversion also depends on power density falling on the emitter surface, and that a power conversion efficiency of graphene-based solar TEC as high as 55% can be easily achieved (in the absence of the space-charge effect) through proper choice of work functions, collector temperature, and emissivity of emitter surfaces. Such solar energy conversion would reduce our dependence on silicon solar panels and offers great potential for future renewable energy utilization.

  14. Mimicry in online conversations : an exploratory study of linguistic analysis techniques

    NARCIS (Netherlands)

    Carrick, Tom; Rashid, Awais; Taylor, Paul Jonathon; Kumar, Ravi; Caverlee, James; Tong, Hanghang

    2016-01-01

    A number of computational techniques have been proposed that aim to detect mimicry in online conversations. In this paper, we investigate how well these reflect the prevailing cognitive science model, i.e. the Interactive Alignment Model. We evaluate Local Linguistic Alignment, word vectors, and

  15. Assessment of BSBA Students' Conversancy in Current Business Issues: A Case Study

    Science.gov (United States)

    Hogan, Eileen A.; Maskulka, Therese A.; Kaminski, Kathleen A.

    2014-01-01

    In 2008, the faculty of the College of Business at Kutztown University developed a set of five learning goals for its BSBA program. In fall, 2011, the college's Assurance of Learning Committee began to pursue the assessment of the last of these goals: "BSBA graduates will be conversant in current business issues, including ethics, social…

  16. Conversation Analysis.

    Science.gov (United States)

    Schiffrin, Deborah

    1990-01-01

    Summarizes the current state of research in conversation analysis, referring primarily to six different perspectives that have developed from the philosophy, sociology, anthropology, and linguistics disciplines. These include pragmatics; speech act theory; interactional sociolinguistics; ethnomethodology; ethnography of communication; and…

  17. Complementary and Alternative Medicine: A Cross-Sectional Observational Study in Pediatric Inpatients.

    Science.gov (United States)

    Dhankar, Mukesh

    2018-01-01

    The aim was to study the prevalence of complementary and alternative medicine use in acutely sick hospitalized children and factors associated with it. This is a cross-sectional, hospital-based study in a tertiary care center of Delhi, India. Children admitted to a pediatric unit during the study period were assessed using a specially designed questionnaire. Out of the total 887 admitted children, 161 (18.1%) were using complementary and alternate medicine in one form or another. Of these, 113 (70.2%) were using complementary and alternate medicine for the current illness directly leading to admission and the remaining 48 (29.8%) had used complementary and alternate medicine in past. The common complementary and alternate medicine use observed in our study was combined ayurveda and spiritual approach (25.5%), ayurveda (24.8%), spiritual (21.7%), homeopathic (13%), and 47.2% of children were using spiritual approach in form of Jhada (tying piece of cloth on arm or leg or keeping a knife by the side of child). The significant factors associated with complementary and alternate medicine use were younger age, female gender, and father being employed. Complementary and alternate medicine is commonly used even in acutely sick children.

  18. A neutronic feasibility study for LEU conversion of the High Flux Beam Reactor (HFBR)

    International Nuclear Information System (INIS)

    Pond, R.B.; Hanan, N.A.; Matos, J.E.

    1997-01-01

    A neutronic feasibility study for converting the High Flux Beam Reactor at Brookhaven National Laboratory from HEU to LEU fuel was performed at Argonne National Laboratory. The purpose of this study is to determine what LEU fuel density would be needed to provide fuel lifetime and neutron flux performance similar to the current HEU fuel. The results indicate that it is not possible to convert the HFBR to LEU fuel with the current reactor core configuration. To use LEU fuel, either the core needs to be reconfigured to increase the neutron thermalization or a new LEU reactor design needs to be considered. This paper presents results of reactor calculations for a reference 28-assembly HEU-fuel core configuration and for an alternative 18-assembly LEU-fuel core configuration with increased neutron thermalization. Neutronic studies show that similar in-core and ex-core neutron fluxes, and fuel cycle length can be achieved using high-density LEU fuel with about 6.1 gU/cm 3 in an altered reactor core configuration. However, hydraulic and safety analyses of the altered HFBR core configuration needs to be performed in order to establish the feasibility of this concept. (author)

  19. The role of community conversations in facilitating local HIV competence: case study from rural Zimbabwe.

    Science.gov (United States)

    Campbell, Catherine; Nhamo, Mercy; Scott, Kerry; Madanhire, Claudius; Nyamukapa, Constance; Skovdal, Morten; Gregson, Simon

    2013-04-17

    This paper examines the potential for community conversations to strengthen positive responses to HIV in resource-poor environments. Community conversations are an intervention method through which local people work with a facilitator to collectively identify local strengths and challenges and brainstorm potential strategies for solving local problems. We conducted 18 community conversations (with six groups at three points in time) with a total of 77 participants in rural Zimbabwe (20% HIV positive). Participants were invited to reflect on how they were responding to the challenges of HIV, both as individuals and in community groups, and to think of ways to better support openness about HIV, kindness towards people living with HIV and greater community uptake of HIV prevention and treatment. Community conversations contributed to local HIV competence through (1) enabling participants to brainstorm concrete action plans for responding to HIV, (2) providing a forum to develop a sense of common purpose in relation to implementing these, (3) encouraging and challenging participants to overcome fear, denial and passivity, (4) providing an opportunity for participants to move from seeing themselves as passive recipients of information to active problem solvers, and (5) reducing silence and stigma surrounding HIV. Our discussion cautions that community conversations, while holding great potential to help communities recognize their potential strengths and capacities for responding more effectively to HIV, are not a magic bullet. Poverty, poor harvests and political instability frustrated and limited many participants' efforts to put their plans into action. On the other hand, support from outside the community, in this case the increasing availability of antiretroviral treatment, played a vital role in enabling communities to challenge stigma and envision new, more positive, ways of responding to the epidemic.

  20. ALTERNATIVE AND ENHANCED CHEMICAL CLEANING: BASIC STUDIES RESULTS FY2010

    Energy Technology Data Exchange (ETDEWEB)

    King, W.; Hay, M.

    2011-01-24

    In an effort to develop and optimize chemical cleaning methods for the removal of sludge heels from High Level Waste tanks, solubility tests have been conducted using nonradioactive, pure metal phases. The metal phases studied included the aluminum phase gibbsite and the iron phases hematite, maghemite, goethite, lepidocrocite, magnetite, and wustite. Many of these mineral phases have been identified in radioactive, High Level Waste sludge at the Savannah River and Hanford Sites. Acids evaluated for dissolution included oxalic, nitric, and sulfuric acids and a variety of other complexing organic acids. The results of the solubility tests indicate that mixtures of oxalic acid with either nitric or sulfuric acid are the most effective cleaning solutions for the dissolution of the primary metal phases in sludge waste. Based on the results, optimized conditions for hematite dissolution in oxalic acid were selected using nitric or sulfuric acid as a supplemental proton source. Electrochemical corrosion studies were also conducted (reported separately; Wiersma, 2010) with oxalic/mineral acid mixtures to evaluate the effects of these solutions on waste tank integrity. The following specific conclusions can be drawn from the test results: (1) Oxalic acid was shown to be superior to all of the other organic acids evaluated in promoting the dissolution of the primary sludge phases. (2) All iron phases showed similar solubility trends in oxalic acid versus pH, with hematite exhibiting the lowest solubility and the slowest dissolution. (3) Greater than 90% hematite dissolution occurred in oxalic/nitric acid mixtures within one week for two hematite sources and within three weeks for a third hematite sample with a larger average particle size. This dissolution rate appears acceptable for waste tank cleaning applications. (4) Stoichiometric dissolution of iron phases in oxalic acid (based on the oxalate concentration) and the formation of the preferred 1:1 Fe to oxalate complex

  1. Alternative Enhanced Chemical Cleaning Basic Studies Results FY09

    Energy Technology Data Exchange (ETDEWEB)

    Hay, M.; King, W.

    2010-05-05

    Due to the need to close waste storage tanks, chemical cleaning methods are needed for the effective removal of the heels. Oxalic acid is the preferred cleaning reagent for sludge heel dissolution, particularly for iron-based sludge, due to the strong complexing strength of the oxalate. However, the large quantity of oxalate added to the tank farm from oxalic acid based chemical cleaning has significant downstream impacts. Optimization of the oxalic acid cleaning process can potentially reduce the downstream impacts from chemical cleaning. To optimize oxalic acid usage, a detailed understanding of the chemistry of oxalic acid based sludge dissolution is required. Additionally, other acid systems may be required for specific waste components with low solubility in oxalic acid and as a means to reduce oxalic acid usage in general. Solubility tests were conducted using non-radioactive, pure metal phases known to be the primary phases present in High Level Waste sludge. The metal phases studied included the aluminum phases gibbsite and boehmite and the iron phases magnetite and hematite. Hematite and boehmite are expected to be the most difficult iron and aluminum phases to dissolve. These mineral phases have been identified in both SRS and Hanford High Level Waste sludge. Acids evaluated for dissolution included oxalic, nitric, and sulfuric acids. The results of the solubility tests indicate that oxalic and sulfuric acids are more effective for the dissolution of the primary sludge phases. For boehmite, elevated temperature will be required to promote effective phase dissolution in the acids studied. Literature reviews, thermodynamic modeling, and experimental results have all confirmed that pH control using a supplemental proton source (additional acid) is critical for minimization of oxalic acid usage during the dissolution of hematite. These results emphasize the importance of pH control in optimizing hematite dissolution in oxalic acid and may explain the somewhat

  2. Alternative Enhanced Chemical Cleaning Basic Studies Results FY09

    International Nuclear Information System (INIS)

    Hay, M.; King, W.

    2010-01-01

    Due to the need to close waste storage tanks, chemical cleaning methods are needed for the effective removal of the heels. Oxalic acid is the preferred cleaning reagent for sludge heel dissolution, particularly for iron-based sludge, due to the strong complexing strength of the oxalate. However, the large quantity of oxalate added to the tank farm from oxalic acid based chemical cleaning has significant downstream impacts. Optimization of the oxalic acid cleaning process can potentially reduce the downstream impacts from chemical cleaning. To optimize oxalic acid usage, a detailed understanding of the chemistry of oxalic acid based sludge dissolution is required. Additionally, other acid systems may be required for specific waste components with low solubility in oxalic acid and as a means to reduce oxalic acid usage in general. Solubility tests were conducted using non-radioactive, pure metal phases known to be the primary phases present in High Level Waste sludge. The metal phases studied included the aluminum phases gibbsite and boehmite and the iron phases magnetite and hematite. Hematite and boehmite are expected to be the most difficult iron and aluminum phases to dissolve. These mineral phases have been identified in both SRS and Hanford High Level Waste sludge. Acids evaluated for dissolution included oxalic, nitric, and sulfuric acids. The results of the solubility tests indicate that oxalic and sulfuric acids are more effective for the dissolution of the primary sludge phases. For boehmite, elevated temperature will be required to promote effective phase dissolution in the acids studied. Literature reviews, thermodynamic modeling, and experimental results have all confirmed that pH control using a supplemental proton source (additional acid) is critical for minimization of oxalic acid usage during the dissolution of hematite. These results emphasize the importance of pH control in optimizing hematite dissolution in oxalic acid and may explain the somewhat

  3. Newly Generated Liquid Waste Processing Alternatives Study, Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Landman, William Henry; Bates, Steven Odum; Bonnema, Bruce Edward; Palmer, Stanley Leland; Podgorney, Anna Kristine; Walsh, Stephanie

    2002-09-01

    This report identifies and evaluates three options for treating newly generated liquid waste at the Idaho Nuclear Technology and Engineering Center of the Idaho National Engineering and Environmental Laboratory. The three options are: (a) treat the waste using processing facilities designed for treating sodium-bearing waste, (b) treat the waste using subcontractor-supplied mobile systems, or (c) treat the waste using a special facility designed and constructed for that purpose. In studying these options, engineers concluded that the best approach is to store the newly generated liquid waste until a sodium-bearing waste treatment facility is available and then to co-process the stored inventory of the newly generated waste with the sodium-bearing waste. After the sodium-bearing waste facility completes its mission, two paths are available. The newly generated liquid waste could be treated using the subcontractor-supplied system or the sodium-bearing waste facility or a portion of it. The final decision depends on the design of the sodium-bearing waste treatment facility, which will be completed in coming years.

  4. Feasibility study for an alternative PWR-containment. Stage 3

    International Nuclear Information System (INIS)

    Eibl, J.

    1994-08-01

    The following report deals with a feasibility study on a lightwater reactor containment which is oriented at the German 1300 MW Convoy Type reactor. It was the aim of this containment development for a future nuclear ractor to restrict all consequences of an extreme reactor failure exclusively to the interior of the containment. Also the decay heat of the relevant core catchers is provided to be removed by passive means. This containment development was a common project with the Nuclear Research Centre at Karlsruhe (KFK). As a consequence of this intention the concept started from upper physical limits, such as a maximum static pressure of 1,5 MPa at 200 , a global and local detonation pressure of 8,4 MPa at an impulse of 5,0 kPas, an upward directed force exerted by the pressure vessel of 300 MN, a horizontal force exerted by the moving pressure vessel onto its environment of 70 MN, a cavern pressure around the core catcher of 3,0 resp., 2,0 MPa and a steam explosion-energy of 300 MJ. Such a contaiment concept is presented and inverstigated with respect to its feasibility, statically and dynamically in all relevant details including earthquake actions. (orig.) [de

  5. Microwave plasma mode conversion

    International Nuclear Information System (INIS)

    Torres, H.S.; Sakanaka, P.H.; Villarroel, C.H.

    1985-01-01

    The behavior of hot electrons during the process of laser-produced plasma is studied. The basic equations of mode conversion from electromagnetic waves to electrostatic waves are presented. It is shown by mode conversion, that, the resonant absorption and parametric instabilities appear simultaneously, but in different plasma regions. (M.C.K.) [pt

  6. Study on alternatives of inertisation of nuclear power plant containment

    International Nuclear Information System (INIS)

    Baron, J.H.; Zarate, S.M.

    1998-01-01

    In the course of a severe accident in a nuclear power plant, the hydrogen generation and other flammable gases, during the core degradation phase and the interaction corium-concrete, could produce the failure of the containment by overpressure of by combustion. According to the analysis of the potential effects of hydrogen evolution, following accidents inside the containment trough a Defense-in depth principle, which attempts to assure that the containment must not fail catastrophically, two techniques have been evaluated: a: Inertisation pre-accident and b: Inertisation post-accident. The technique of inertisation pre-accident consists in replacing the air of the containment with inert-gas like nitrogen (N 2 ) or carbon dioxide (CO 2 ) during the normal operation. The inertisation post-accident in combination with early venting system consists in replacing the air of the containment with inert-gas like nitrogen (N 2 ) or carbon dioxide (CO 2 ), immediately after the beginning of the accident, while the radioactivity is still negligible inside the containment. A system of inertisation pre-accident with nitrogen is used on BWR Mark I and Mark II. Investigations on the inertisation post-accident of the containment atmosphere during severe accidents have been carried out with different objectives from principles of the decade of 1980. Studies concerning hydrogen problem for the nuclear power plants Atucha I and CAREM-25 have permitted to know that the hydrogen generation during an accidental sequence with core degradation, would result important, being able to arrive to form explosive mixtures. In the present work, the applicability of the techniques of inertisation is analyzed for the containment of the Atucha I and CAREM-25, considering the particular design characteristics of these plants. (author) [es

  7. Variability of LD50 Values from Rat Oral Acute Toxicity Studies: Implications for Alternative Model Development

    Science.gov (United States)

    Alternative models developed for estimating acute systemic toxicity are generally evaluated using in vivo LD50 values. However, in vivo acute systemic toxicity studies can produce variable results, even when conducted according to accepted test guidelines. This variability can ma...

  8. Comparative Theology: An Alternative to Religious Studies or Theology of Religions?

    OpenAIRE

    Betül AVCI

    2018-01-01

    This paper examines the relationship between Comparative Theology, Religious Studies and Theology of Religions and questions whether Comparative Theology is an alternative to the last two. Comparative Theology, a faith seeking understanding practice, may be viewed as an alternative to the Enlightenment ideal of Religious Studies, which seeks “impartiality” and “scientific objectivity” in contrast to Comparative Theology’s enquiry into “truth” and “meaning.” I suggest, however, that the compar...

  9. A comparative study of bulk-fill composites: degree of conversion, post-gel shrinkage and cytotoxicity

    Directory of Open Access Journals (Sweden)

    Flávia Gonçalves

    2018-03-01

    Full Text Available Abstract: Bulk-fill composites are claimed to be restorative materials used in deep preparations and effectively photoactivated in layers up to 4 mm. The aim of the present study was to evaluate the degree of conversion, post-gel volumetric shrinkage, and cytotoxicity of six bulk-fill and two conventional composites. Degree of conversion was determined by FTIR spectroscopy; post-gel volumetric shrinkage was determined using the strain gauge method; and cytotoxicity in human fibroblasts was evaluated indirectly by the MTT assay. Data were subjected to one-way ANOVA/Tukey's test (α = 0.05. All materials, including bulk-fill and conventional composites, were classified as non-toxic, with cell viability higher than 70%. Bulk-fill composites exhibited volumetric shrinkage similar to or lower (1.4 to 0.4% than that of conventional composites (1.7–2.1%. However, only four of the bulk-fill composites were able to sustain a homogeneous conversion at the 4-mm depth. Despite their non-toxicity and shrinkage similar to that of conventional materials, not all commercial bulk-fill materials were able to maintain a conversion as high as 80% of the superficial layer, at the 4-mm depth, indicating some failure in the bulk-fill design of some commercial brands. Therefore, the use of bulk-fill materials in dental practice is advantageous, but special attention should be given to the selection and correct use of the materials.

  10. Microbial conversion of agriculture wastes as a source of energy for developing countries: a case study in Nigeria

    International Nuclear Information System (INIS)

    Ejike, C.; Okereke, G.U.

    1991-01-01

    The direct relationship between level of economic development of any nation and its consumption of energy show that there is improve standard of living with increase in the per capita consumption of energy. In Nigeria, the need to offset some of the economic set backs brought about by increasing fuel costs and chronic lack of foreign currency reserves has compelled her to search for alternative sources of energy. The continuous increase in concern over environmental pollution has also resulted in greater negative cost values of wastes and hence has increased their potential as substrates for bio-derived energy. Cellulosic agricultural wastes are available in Nigeria in large amounts, are ordinarily of little economic value and are non toxic. Nigeria produces about 227,500 tons of animal waste per day implying the bio gas production could be a feasible alternative source of energy. Conversion of agricultural waste to usable energy at commercially acceptable rates involves the availability of raw materials and conversion of same to suitable substrates for fermentation to alcohol and then to bio gas. Saccharomyces spp. produced from fermentation of alcoholic beverages in Northern Nigeria have been used in the production of ethanol from corn corp waste and grass straw. Chromolaena odorata a weed that has no economic value which grows luxuriantly in Nigeria has been used in the generation of bio gas. Drying procedure and pH are among other conditions the affect methane yield. The development of the biotechnology of bio-derivable energy from agricultural waste if effectively harnessed will help to aleviate the energy problems of developing countries. The climate for the promotion of this technology is favourable because of low cost of raw material, high cost of fuel energy, and poor foreign exchange earning capacity of developing countries. (author)

  11. Catalytic Conversion of Carbohydrates

    DEFF Research Database (Denmark)

    Osmundsen, Christian Mårup

    a renewable route to aromatics. The conversion of biomass by high temperature processes is a desirable prospect due to the high volumetric production rates which can be achieved, and the ability of these types of processes to convert a wide range of substrates. Current processes however typically have rather...... with the production of commodity chemicals from the most abundantly available renewable source of carbon, carbohydrates. The production of alkyl lactates by the Lewis acid catalyzed conversion of hexoses is an interesting alternative to current fermentation based processes. A range of stannosilicates were...... to be an efficient initial conversion step in the utilization of biomass for chemicals production. The shift from an oil based chemical industry to one based on renewable resources is bound to happen sooner or later, however the environmental problems associated with the burning of fossil resources means...

  12. Study of Thermally Responsive Ionic Liquids for Novel Water Desalination and Energy Conversion Applications

    KAUST Repository

    Zhong, Yujiang

    2018-04-01

    The rapidly expanding of the global population in the 21st-century forces people facing two serious problems: water scarcity and energy shortage. Enormous continuous studies focus on providing enough fresh water and energy in a sustainable way. This thesis aims at exploring novel membrane processes based on thermally responsive ionic liquids with the upper critical solution temperature (UCST ILs) for water desalination and energy conversion from low-grade heat energy to electricity. A UCST IL protonated betaine bis(trifluoromethylsulfonyl)imide ([Hbet][Tf2N]) was first experimentally studied as a novel draw solute in a thermal forward osmosis (FO). A 3.2 M [Hbet][Tf2N] solution can be obtained via spontaneous phase separation from an IL and water mixture at room temperature. By heating and maintaining the temperature above 56°C, this solution can draw water from high-salinity solution up to 3.0 M, 5 times salty as the sea water. The IL draw solution can be easily regenerated by phase separation. Conducting the FO process at higher temperatures can also increase the water flux. According to the different choices of the freshwater polishing step, the electric energy consumption in this novel process was estimated as 26.3% to 64.2% of conventional one-step sea water reverse osmosis. Two UCST ILs with better performance, [Hbet][Tf2N] and choline bis(trifluoromethylsulfonyl)imide ([Choline][Tf2N]), were selected as the agents in a novel closed-loop thermally responsive IL osmotic heat engine (TRIL-OHE) to convert low-grade thermal energy to electricity. The specific energies of the [Hbet][Tf2N] system and the [Choline][Tf2N] system are 2500 kJ/t and 3700 kJ/t, which are 2.7 and 4.0 times of the seawater and river water system, respectively. The maximum power density measured from a commercial FO membrane is 1.5 W/m2 for the [Hbet][Tf2N] system and 2.3 W/m2 for the [Choline][Tf2N] system, leaving a big room to improve if highly permeable membranes are used. Another

  13. Alternative medicine in Paris and Rio de Janeiro: a study on transformative health experiences

    Directory of Open Access Journals (Sweden)

    Elisabeth Eglem

    2014-06-01

    Full Text Available The purpose of this paper is to explore the practice of alternative medicine as an experience capable of modifying the very perception of the body and body feeling, based in a two-field research in France (Paris and Brazil (Rio de Janeiro. In this research, the resort to alternative medicines was considered as urban practice and a possible response to emotional needs, beyond the curative specificities of these medicines. The two countries were chosen for their supposed complementarity concerning the perception of spirituality and therefore, the perception of holistic health concepts. The study relies on an inductive approach and a qualitative methodology: introspective interviews with consumers and professionals, as well as participant observations. After a review of the theoretical aspects on the subject — concepts related to health, alternative medicine, transformative experience —, empirical results are presented. They show that the experience of alternative medicine tends to modify body perception, understood as how individuals define their own body. It also tends to modify body internal feeling, literally how people feel their body. The second conclusion that can be drawn from our study is that, beyond cultural specificities, some similarities appear in the way the practice of alternative medicine impacts on body perception and individual values. In that sense, alternative medicine practices in big urban centers appear to be related to a global consumer culture. However, alternative health behaviors rely on a subjective quest of sense which can be expressed through a variety of practices related to better health, not necessarily involving consumption.

  14. Ortho-para H₂ conversion by proton exchange at low temperature: an accurate quantum mechanical study.

    Science.gov (United States)

    Honvault, P; Jorfi, M; González-Lezana, T; Faure, A; Pagani, L

    2011-07-08

    We report extensive, accurate fully quantum, time-independent calculations of cross sections at low collision energies, and rate coefficients at low temperatures for the H⁺ + H₂(v = 0, j) → H⁺ + H₂(v = 0, j') reaction. Different transitions are considered, especially the ortho-para conversion (j = 1 → j' = 0) which is of key importance in astrophysics. This conversion process appears to be very efficient and dominant at low temperature, with a rate coefficient of 4.15 × 10⁻¹⁰ cm³ molecule⁻¹ s⁻¹ at 10 K. The quantum mechanical results are also compared with statistical quantum predictions and the reaction is found to be statistical in the low temperature regime (T < 100 K).

  15. Supervised artificial neural network-based method for conversion of solar radiation data (case study: Algeria)

    Science.gov (United States)

    Laidi, Maamar; Hanini, Salah; Rezrazi, Ahmed; Yaiche, Mohamed Redha; El Hadj, Abdallah Abdallah; Chellali, Farouk

    2017-04-01

    In this study, a backpropagation artificial neural network (BP-ANN) model is used as an alternative approach to predict solar radiation on tilted surfaces (SRT) using a number of variables involved in physical process. These variables are namely the latitude of the site, mean temperature and relative humidity, Linke turbidity factor and Angstrom coefficient, extraterrestrial solar radiation, solar radiation data measured on horizontal surfaces (SRH), and solar zenith angle. Experimental solar radiation data from 13 stations spread all over Algeria around the year (2004) were used for training/validation and testing the artificial neural networks (ANNs), and one station was used to make the interpolation of the designed ANN. The ANN model was trained, validated, and tested using 60, 20, and 20 % of all data, respectively. The configuration 8-35-1 (8 inputs, 35 hidden, and 1 output neurons) presented an excellent agreement between the prediction and the experimental data during the test stage with determination coefficient of 0.99 and root meat squared error of 5.75 Wh/m2, considering a three-layer feedforward backpropagation neural network with Levenberg-Marquardt training algorithm, a hyperbolic tangent sigmoid and linear transfer function at the hidden and the output layer, respectively. This novel model could be used by researchers or scientists to design high-efficiency solar devices that are usually tilted at an optimum angle to increase the solar incident on the surface.

  16. Study of electron beam energy conversion at gyrocon-linear accelerator facility

    International Nuclear Information System (INIS)

    Karliner, M.M.; Makarov, I.G.; Ostreiko, G.N.

    2004-01-01

    A gyrocon together with the high-voltage 1.5 MeV accelerator ELIT-3A represents a power generator at 430 MHz serving for linear electron accelerator pulse driving. The facility description and results of calorimetric measurements of ELIT-3A electron beam power and accelerated beam at the end of accelerator are presented in the paper. The achieved energy conversion efficiency is about 55%

  17. Numerical study of hydrodynamic behavior and conversion efficiency of a two-buoy wave energy converter

    Science.gov (United States)

    Yang, Cen; Zhang, Yong-liang

    2018-04-01

    In this paper we propose a two-buoy wave energy converter composed of a heaving semi-submerged cylindrical buoy, a fixed submerged cylindrical buoy and a power take-off (PTO) system, and investigate the effect of the fixed submerged buoy on the hydrodynamics of the heaving semi-submerged buoy based on the three-dimensional potential theory. And the dynamic response of the semi-submerged buoy and the wave energy conversion efficiency of the converter are analyzed. The difference of the hydrodynamics and the wave energy conversion efficiency of a semi-submerged buoy converter with and without a fixed submerged buoy is discussed. It is revealed that the influence of the fixed submerged buoy on the exciting wave force, the added mass, the radiation damping coefficient and the wave energy conversion efficiency can be significant with a considerable variation, depending on the vertical distance between the heaving semi-submerged buoy and the fixed submerged buoy, the diameter ratio of the fixed submerged buoy to the heaving semi-submerged buoy and the water depth.

  18. The Effectiveness of Strategic Activities on the Conversational Skills A Case Study: Persian Language Learners Abroad

    Directory of Open Access Journals (Sweden)

    Zahra Abolhassani Chimeh

    2017-04-01

    Full Text Available This paper investigates the effectiveness of those activities which are based on all types of strategies for teaching conversational skills. These strategies are practiced in the form of 17 activities and their effectiveness on the oral language performane of Persian learners has been investigated. The second language learning strategies in this research are dependent on two Kuhn's paradigms and include "learning" and "using" second language. The former consists of recognition and acceptance of materials, distinction from other materials, categorizing them for a better learning, constant involvement with materials, using common memorization methods for rehearsal to improve natural conversation learning. The teacher's Linguistics and Iranology knowledge in choosing teaching materials, producing similarities and differences in two languages, lexical and syntactic categorizations of activities based on the first to the third strategies were implemented in the classroom. Informal gatherings, appropriate assignments of certain tasks like memorizing the dialogues or proverbs were practiced for the fourth and the fifth strategies. These strategies were applied on 19 undergaduate intermediate Persian language learners, with Slav mother tongue in 5 successive semesters from 2011 to 2013. In this research, it was affirmed that there is a positive correlation between using strategic activities with the improvement of converational skill of language learners. That is, the more learners are active in the activities related to strategies, the better they become in the conversational skill.

  19. A Correlation Study on Attachment Style and GPA of Students at an Alternative Education Center

    OpenAIRE

    Cindy L. Burdick

    2014-01-01

    Adolescents in America are dropping out of school in alarming rates. In the school year 2009- 2010, 514,238 adolescents dropped out of high school. While alternative education centers have been created to meet the needs of these individuals, they are not always successful as evidenced by a graduation rate below 5% in several alternative centers in Florida. Previous studies have shown that students with a positive attachment style have higher grade point averages (GPA) and perform better in sc...

  20. Comparative Theology: An Alternative to Religious Studies or Theology of Religions?

    Directory of Open Access Journals (Sweden)

    Betül AVCI

    2018-03-01

    Full Text Available This paper examines the relationship between Comparative Theology, Religious Studies and Theology of Religions and questions whether Comparative Theology is an alternative to the last two. Comparative Theology, a faith seeking understanding practice, may be viewed as an alternative to the Enlightenment ideal of Religious Studies, which seeks “impartiality” and “scientific objectivity” in contrast to Comparative Theology’s enquiry into “truth” and “meaning.” I suggest, however, that the comparative method employed by both Religious Studies and Comparative Theology is not a neutral space. Hence, the new comparativism in Religious Studies reinstates its search for understanding and its political stand, which blurs the boundaries between Comparative Theology and Religious Studies. Likewise, while Comparative Theology is distinct from the Theology of Religions, it does not pose an alternative to it because Comparative Theology, too, often embodies either a pluralist or an inclusivist approach.

  1. CONTENT ANALYSIS, DISCOURSE ANALYSIS, AND CONVERSATION ANALYSIS: PRELIMINARY STUDY ON CONCEPTUAL AND THEORETICAL METHODOLOGICAL DIFFERENCES

    Directory of Open Access Journals (Sweden)

    Anderson Tiago Peixoto Gonçalves

    2016-08-01

    Full Text Available This theoretical essay aims to reflect on three models of text interpretation used in qualitative research, which is often confused in its concepts and methodologies (Content Analysis, Discourse Analysis, and Conversation Analysis. After the presentation of the concepts, the essay proposes a preliminary discussion on conceptual and theoretical methodological differences perceived between them. A review of the literature was performed to support the conceptual and theoretical methodological discussion. It could be verified that the models have differences related to the type of strategy used in the treatment of texts, the type of approach, and the appropriate theoretical position.

  2. Conversion electron Moessbauer and XPS study on the effect of polishing of a stainless steel sample

    International Nuclear Information System (INIS)

    Vertes, Cs.; Kuzmann, E.; Lakatos-Varsanyi, M.; Vertes, A.; Vass, G.; Romhanyi, K.

    1994-01-01

    Conversion electron Moessbauer spectroscopy (CEMS) and XPS has been used for the surface analysis of an 'X10CrNiTi 18/9 (DIN 1.7440)'-type stainless steel in order to determine the supposed structural and/or chemical changes in the surface layer caused by polishing. Both, CEMS and XPS results can be associated with the appearance of Fe nitride in the outer layer of steel samples after polishing, while no sing of nitrogen was detected in the bulk material. (author) 9 refs.; 3 figs.; 1 tab

  3. Recent Advances in the Mechanistic Studies of Alkylaromatic Conversions over Zeolite Catalysts

    International Nuclear Information System (INIS)

    Min, Hyung-Ki; Hong, Suk Bong

    2013-01-01

    The transformation of alkylaromatic hydrocarbons using zeolite catalysts play big part in the current petrochemical industry. Here we review recent advances in the understanding of the reaction mechanisms of various alkylaromatic conversions with respect to the structural and physicochemical properties of zeolite catalysts employed. Indeed, the shape-selective nature of zeolite catalysts determines the type of reaction intermediates and hence the prevailing reaction mechanism together with the product distribution. The prospect of zeolite catalysis in the development of more efficient petrochemical processes is also described

  4. Engineering the central pathways in Lactococcus lactis: functional expression of the phosphofructokinase (pfk) and alternative oxidase (aox1) genes from Aspergillus niger in Lactococcus lactis facilitates improved carbon conversion rates under oxidizing conditions.

    Science.gov (United States)

    Papagianni, Maria; Avramidis, Nicholaos

    2012-08-10

    The present work describes a novel central pathway engineering method that has been designed with the aim to increase the carbon conversion rates under oxidizing conditions in L. lactis fermentations. The nisin producer L. lactis ATCC11454 strain has been genetically engineered by cloning a truncated version of the phosphofructokinase gene (pfk13), along with the pkaC, encoding for the catalytic subunit of cAMP-dependent protein kinase, and the alternative oxidase (aox1) genes of A. niger. Functional expression of the above genes resulted in enhanced PFK activity and the introduction of AOX activity and alternative respiration in the presence of a source of heme in the substrate, under fully aerobic growth conditions. The constructed strain is capable of fermenting high concentrations of glucose as was demonstrated in a series of glucostat fed-batch fermentations with glucose levels maintained at 55, 138 and 277 mM. The high maximum specific uptake rate of glucose of 1.8 mMs(-1)gCDW(-1) at 277 mM glucose is characteristic of the improved ability of the microorganism to handle elevated glucose concentrations under conditions otherwise causing severe reduction of PFK activity. The increased carbon flow through glycolysis led to increased protein synthesis that was reflected in increased biomass and nisin levels. The pfk 13-pkaC-aox1-transformant strain's fermentation at 277 mM glucose gave a final biomass concentration of 7.5 g/l and nisin activity of 14,000 IU/ml which is, compared to the parental strain's production levels at its optimal 55 mM glucose, increased by a factor of 2.34 for biomass and 4.37 for nisin. Copyright © 2012 Elsevier Inc. All rights reserved.

  5. Pictorial Conversations.

    Science.gov (United States)

    Hooper, Kristina

    1982-01-01

    Provides the rationale for considering communication in a graphic domain and suggests a specific goal for designing work stations which provide graphic capabilities in educational settings. The central element of this recommendation is the "pictorial conversation", a highly interactive exchange that includes pictures as the central elements.…

  6. The modified gait abnormality rating scale in patients with a conversion disorder: a reliability and responsiveness study.

    Science.gov (United States)

    Vandenberg, Justin M; George, Deanna R; O'Leary, Andrea J; Olson, Lindsay C; Strassburg, Kaitlyn R; Hollman, John H

    2015-01-01

    Individuals with conversion disorder have neurologic symptoms that are not identified by an underlying organic cause. Often the symptoms manifest as gait disturbances. The modified gait abnormality rating scale (GARS-M) may be useful for quantifying gait abnormalities in these individuals. The purpose of this study was to examine the reliability, responsiveness and concurrent validity of GARS-M scores in individuals with conversion disorder. Data from 27 individuals who completed a rehabilitation program were included in this study. Pre- and post-intervention videos were obtained and walking speed was measured. Five examiners independently evaluated gait performance according to the GARS-M criteria. Inter- and intrarater reliability of GARS-M scores were estimated with intraclass correlation coefficients (ICCs). Responsiveness was estimated with the minimum detectable change (MDC). Pre- to post-treatment changes in GARS-M scores were analyzed with a dependent t-test. The correlation between GARS-M scores and walking speed was analyzed to assess concurrent validity. GARS-M scores were quantified with good-to-excellent inter- (ICC = 0.878) and intrarater reliability (ICC = 0.989). The MDC was 2 points. Mean GARS-M scores decreased from 7 ± 5 at baseline to 1 ± 2 at discharge (t26 = 7.411, p conversion disorder. GARS-M scores provide objective measures upon which treatment effects can be assessed. Copyright © 2014 Elsevier B.V. All rights reserved.

  7. Characteristics and Outcomes of Children With Conversion Disorder Admitted to a Single Inpatient Rehabilitation Unit, A Retrospective Study.

    Science.gov (United States)

    Bolger, Ashlee; Collins, Andrew; Michels, Michelle; Pruitt, David

    2018-03-14

    Conversion disorder (CD) can lead to impaired functioning. Few studies present demographic and outcome data for pediatric patients. Many have had success with rehabilitation; however, further details are not known. To identify characteristics and outcomes of children admitted to a pediatric inpatient rehabilitation program with CD symptoms. Retrospective study. Inpatient rehabilitation unit within a large children's hospital. All patients with diagnosis of CD or functional gait disorder (FGD) during designated time period. Data were obtained from chart review and United Data Systems for Medical Rehabilitation. Descriptive statistics and Wilcoxon signed rank tests were used to analyze data. A P value of conversion disorder symptoms in the 12 months following discharge, and school reentry characteristics. 30 admissions were identified that met criteria. Before diagnosis, duration of symptoms was 58 ± 145 days, physician visits averaged 1.9 ± 2.1, hospital admissions to the same hospital averaged 0.7 ± 0.9, and absence from school was 6 ± 12 weeks. Overall, 83% exhibited mixed symptoms. Length of inpatient rehabilitation stay was 8.4 ± 4.2 days with WeeFIM score change of 30 ± 11.9 (P conversion disorder and leads to sustained functional improvement and return to school after discharge. ?? Copyright © 2018 American Academy of Physical Medicine and Rehabilitation. Published by Elsevier Inc. All rights reserved.

  8. Wabash Valley Integrated Gasification Combined Cycle, Coal to Fischer Tropsch Jet Fuel Conversion Study

    Energy Technology Data Exchange (ETDEWEB)

    Shah, Jayesh [Lummus Technology Inc., Bloomfield, NJ (United States); Hess, Fernando [Lummus Technology Inc., Bloomfield, NJ (United States); Horzen, Wessel van [Lummus Technology Inc., Bloomfield, NJ (United States); Williams, Daniel [Lummus Technology Inc., Bloomfield, NJ (United States); Peevor, Andy [JM Davy, London (United Kingdom); Dyer, Andy [JM Davy, London (United Kingdom); Frankel, Louis [Canonsburgh, PA (United States)

    2016-06-01

    This reports examines the feasibility of converting the existing Wabash Integrated Gasification Combined Cycle (IGCC) plant into a liquid fuel facility, with the goal of maximizing jet fuel production. The fuels produced are required to be in compliance with Section 526 of the Energy Independence and Security Act of 2007 (EISA 2007 §526) lifecycle greenhouse gas (GHG) emissions requirements, so lifecycle GHG emissions from the fuel must be equal to or better than conventional fuels. Retrofitting an existing gasification facility reduces the technical risk and capital costs associated with a coal to liquids project, leading to a higher probability of implementation and more competitive liquid fuel prices. The existing combustion turbine will continue to operate on low cost natural gas and low carbon fuel gas from the gasification facility. The gasification technology utilized at Wabash is the E-Gas™ Technology and has been in commercial operation since 1995. In order to minimize capital costs, the study maximizes reuse of existing equipment with minimal modifications. Plant data and process models were used to develop process data for downstream units. Process modeling was utilized for the syngas conditioning, acid gas removal, CO2 compression and utility units. Syngas conversion to Fischer Tropsch (FT) liquids and upgrading of the liquids was modeled and designed by Johnson Matthey Davy Technologies (JM Davy). In order to maintain the GHG emission profile below that of conventional fuels, the CO2 from the process must be captured and exported for sequestration or enhanced oil recovery. In addition the power utilized for the plant’s auxiliary loads had to be supplied by a low carbon fuel source. Since the process produces a fuel gas with sufficient energy content to power the plant’s loads, this fuel gas was converted to hydrogen and exported to the existing gas turbine for low carbon power production. Utilizing low carbon fuel gas and

  9. Study of the thermal conversions of organic carbon of Huadian oil shale during pyrolysis

    International Nuclear Information System (INIS)

    Chen, Bin; Han, Xiangxin; Li, Qingyou; Jiang, Xiumin

    2016-01-01

    Highlights: • Long-chain alkenes’ formation needs less energy than short ones. • The rupture tends to happen at the middle position of long alkyl chains first. • Cycloparaffins tend to be cracked rather than to be dehydrogenated. - Abstract: The essence of kerogen decomposition in retorting process is organic carbon conversion. FTIR and GC-MS methods were employed in analyzing the conversion process of “kerogen → bitumen” and “bitumen → shale oil” in this paper. To achieve a deeper investigation of thermochemical transformation of organic carbon during the oil shale retorting, a set of physical models of carbon chains were constructed and analyzed using the transition state theory (TST) of quantum chemistry with gauss03 package. According to the results, the main reactions in the transformation of kerogen to bitumen are the re-integration of macromolecular structure and the breakup of oxygen-bridged bonds. Long alkyl chains containing functional groups decompose and transform to shorter alkanes, alkenes and aliphatic free radicals. The rupture of alkanes happens first at the middle position of long carbon chains. Alkyl free radicals further convert to alkanes, alkenes or aromatic rings. The alkanes take the highest content in shale oil.

  10. Preliminary Study of Printed Circuit Heat Exchanger (PCHE) for various power conversion systems for SMART

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, Jinsu; Baik, Seungjoon; Lee, Jeong Ik [KAIST, Daejeon (Korea, Republic of)

    2016-10-15

    The steam-Rankine cycle was the most widely used power conversion system for a nuclear power plant. The size of the heat exchanger is important for the modulation. Such a challenge was conducted by Kang et al. They change the steam generator type for the SMART from helical type heat exchanger to Printed Circuit Heat Exchanger (PCHE). Recently, there has been a growing interest in the supercritical carbon dioxide (S-CO{sub 2}) Brayton cycle as the most promising power conversion system. The reason is high efficiency with simple layout and compact power plant due to small turbomachinery and compact heat exchanger technology. That is why the SCO{sub 2} Brayton cycle can enhance the existing advantages of Small Modular Reactor (SMR) like SMART, such as reduction in size, capital cost, and construction period. Thermal hydraulic and geometric parameters of a PCHE for the S-CO{sub 2} power cycle coupled to SMART. The results show that the water - CO{sub 2} printed circuit heat exchanger size is smaller than printed circuit steam generator for the superheated steam Rankine cycle. This results show the potential benefit of using the S-CO-2 Brayton power cycle to a water-cooled small modular reactor.

  11. Studies on the induction of mitotic gene conversion by ultraviolet irradiation

    International Nuclear Information System (INIS)

    Ito, T.; Kobayashi, K.

    1975-01-01

    Action spectra for the induction of intragenic mitotic recombination (gene conversion) at the trp 5 locus by UV are presented for three cell stages (T 0 , T 9 and T 16 ) taken from synchronously growing cultures of Saccharomyces cerevisiae. The spectra over the range from 230 to 300 nm were taken mostly in 5-nm steps. The peak in the action spectra was significantly shifted, regardless of the stage, towards the longer wavelengths as compared with that of the absorption spectrum of DNA (258nm) or even that of thymine (265nm). In one extreme case ( 16 ), the peak was shifted 17nm from the absorption peak of DNA. Further, the spectrum changed its shape as the cell stage advanced from the non-dividing (unbudded) (T 0 ) to a dividing phase (T 16 ). Furthermore, the induction cross section decreased by a large factor (about 40), regardless of the wavelength, in going from the non-dividing to a dividing phase. From observations of the high photoreversibility of induced conversions, the major primary damage was thought to be pyrimidine dimers in the DNA

  12. Study of the application of a near-real-time materials accountancy system for a model plutonium conversion plants

    International Nuclear Information System (INIS)

    Ihara, Hitoshi; Ikawa, Koji

    1986-11-01

    An assessment was done on the potential capability of a Near-Real-Time materials accountancy system for a model plutonium conversion plant. To this end, a computer simulation system, DYSAS-C, has been developed and evaluated through this assessment study. This study showed that N.R.T.A system could be used not only as a good operator's accounting system but also as a useful inspectorate's system to detect an abrupt diversion. It also showed, however, that more elaborated NRTA system which have not yet evaluated in this study should be considerered when we wish to improve of detecting protracted diversion. (author)

  13. A study on the capture of carbon dioxide from a large refinery power station boiler by conversion to oxyfuel operation

    Energy Technology Data Exchange (ETDEWEB)

    Wilkinson, M.B.; Boden, J.C.; Panesar, R.S.; Allam, R.J. [BP Amoco, Sunbury-on-Thames (United Kingdom)

    2001-07-01

    A detailed feasibility study has been carried out on the conversion of an existing refinery power station boiler, fired with refinery off-gas, to oxyfuel operation with carbon dioxide capture. The conversion was shown to be technically feasible using proven technologies. Boiler output could be maintained without significant pressure-part modifications and there would be no loss of boiler efficiency. It would be possible to retain a capability to operate in conventional air firing mode for start-up and emergency situations. The concept has been developed to a stage where a demonstration plant could be designed. The major elements of the capital costs of conversion are associated with the air separation unit and the carbon dioxide treatment and compression train and the additional operating costs are associated principally with the power consumption of these units. Further optimisation of the oxyfuel combustion system is possible and it is anticipated that the ongoing developments in air separation technology will help to make significant reductions in these costs in the future. 5 refs., 6 figs.

  14. A Study on Becoming an Alternatively Certified Career and Technical Educator

    Science.gov (United States)

    Cotton-Flanagan, Kymberli A.

    2011-01-01

    This mixed method study examined the perspectives of twelve practicing high school CTE teachers engaged in a newly approved university model for alternative certification. Using Creswell's (2008) Sequential Exploratory Design and the lens of adult learning theory as established in Knowles' (1970) Theory of Andragogy, this study examines how…

  15. Using an Empirical Binomial Hierarchical Bayesian Model as an Alternative to Analyzing Data from Multisite Studies

    Science.gov (United States)

    Hardin, J. Michael; Anderson, Billie S.; Woodby, Lesa L.; Crawford, Myra A.; Russell, Toya V.

    2008-01-01

    This article explores the statistical methodologies used in demonstration and effectiveness studies when the treatments are applied across multiple settings. The importance of evaluating and how to evaluate these types of studies are discussed. As an alternative to standard methodology, the authors of this article offer an empirical binomial…

  16. Why We Teach: Autobiographies of Traditionally and Alternatively Certified Pre-Service Social Studies Teachers

    Science.gov (United States)

    Santoli, Susan

    2009-01-01

    This study describes the analysis of the social studies autobiographies of 46 students compiled over a 15 month period. Two major questions were addressed: (1) what motivational patterns are revealed in these autobiographies and (2) what differences and similarities exist in the autobiographies of students seeking alternative and traditional…

  17. Study and experimental verification of control tuning strategies in a variable speed wind energy conversion system

    Energy Technology Data Exchange (ETDEWEB)

    Zaragoza, Jordi; Pou, Josep; Arias, Antoni [Electronic Engineering Dept., Technical University of Catalonia, Campus Terrassa, C. Colom 1, 08222 Terrassa (Spain); Spiteri, Cyril [Department of Industrial Electrical Power Conversion, University of Malta, Faculty of Engineering, Msida (Malta); Robles, Eider; Ceballos, Salvador [Energy Unit, Robotiker-Tecnalia Technology Corporation, Zamudio, Basque Country (Spain)

    2011-05-15

    This paper analyzes and compares different control tuning strategies for a variable speed wind energy conversion system (WECS) based on a permanent-magnet synchronous generator (PMSG). The aerodynamics of the wind turbine (WT) and a PMSG have been modeled. The control strategy used in this research is composed of three regulators, which may be based on either linear or nonlinear controllers. In this analysis, proportional-integral (PI) linear controllers have been used. Two different tuning strategies are analyzed and compared. The main goal is to enhance the overall performance by achieving a low sensitivity to disturbances and minimal overshoot under variable operating conditions. Finally, the results have been verified by an experimental WECS laboratory prototype. (author)

  18. Raw materials evaluation and process development studies for conversion of biomass to sugars and ethanol

    Energy Technology Data Exchange (ETDEWEB)

    Wilke, C.R.; Yang, R.D.; Sciamanna, A.S.; Freitas, R.P.

    1978-06-01

    A range of cellulosic raw materials in the form of agricultural crop residue was analyzed for chemical composition and assessed for potential yields of sugars through chemical pretreatment and enzymatic hydrolysis of these materials. Corn stover was used as a representative raw material for a preliminary process design and economic assessment of the production of sugars and ethanol. With the process as presently developed, 23 gallons of ethanol can be obtained per ton of corn stover at a processing cost of about $1.80 per gallon exclusive of by-product credits. The analysis shows the cost of ethanol to be highly dependent upon (1) the cost of the biomass, (2) the extent of conversion to glucose, (3) enzyme recovery and production cost and (4) potential utilization of xylose. Significant cost reduction appears possible through further research in these directions.

  19. Tritium conversion in tritiated water: study of the involved reactions: a literature survey

    International Nuclear Information System (INIS)

    Ballereau, P.

    1987-10-01

    According to ICRP publication 30, hazards due to molecular tritium are not significant in comparison to hazards due to the oxidated form: tritiated water. It is thus important to know the kinetics of tritium/tritiated water conversion to obtain a realistic evaluation of the risks for the environment at level of present facilities and of future nuclear fusion facilities. Laboratory experiments in static contained conditions have shown that tritiated water is produced by two mechanisms: gas phase oxidation, hydrogen isotopic exchange with water. The periods found are relatively long and difficult to specify. In terrestrial atmosphere, the two mechanisms intervening in tritiated water formation are photochemical oxidation and biochemical reactions occurring in soil and in vegetation aerial parts. The corresponding periods are of some years for the first one, of some hours for the second one [fr

  20. Parametric studies for the nuclear design of high-conversion pressurized water reactors

    International Nuclear Information System (INIS)

    Axmann, J.; Oldekop, W.

    1987-01-01

    Undermoderated high-conversion pressurized water reactors with steel canning tubes offer the possibility of high burnup together with a comparatively low consumption of fissionable material; however, they require a relatively large inventory of fissionable material. The effects of different fuel compositions upon the specific consumption of fissionable material are investigated for a fixed burnup and moderator-to-fuel volume ratios varying between 0.5 and 2.0. Moreover, the required inventory of fissionable material is determined and the influence on the costs of electric power generation is shown. Further investigations deal with the neutron-physical effects of decreasing fuel rod diameters and the influence of differing steel additives. It appears that the parasitic neutron absorption by alloying constituents depends on the moderation level in a non-uniform manner and that the contribution of the fissionable material to the electric power generation costs is rather independent of the moderator-to-fuel volume ratio. (orig.) [de

  1. Carbon trading as incentive for conversion to organic agriculture. Case study. Organic peanuts in Tanzania

    Energy Technology Data Exchange (ETDEWEB)

    Bodnar, F.

    2005-12-15

    In this pilot project, the climate effects of the conversion from conventional to organic cultivation of peanuts are evaluated. We could aim at voluntary carbon credits that do not comply with the CDM (Clean Development Mechanisms) rules, but we try to meet the CDM rules by combining it with a agroforestry component. However, in the example of Tanzania meeting the CDM rules was a problem. The agricultural system in Tanzania consists of a rotation of several years cultivation and several years fallow. This fallow of grass, shrubs and trees could be considered as 'forest'. Taking fallow land into cultivation would then be deforestation, which would make the planting of trees no longer eligible under CDM. This is a shame because the traditional 'slash and burn' system emits a lot of greenhouse gases.

  2. Municipal solid waste energy conversion study on Guam and American Samoa

    Energy Technology Data Exchange (ETDEWEB)

    1984-03-31

    In the Pacific Islands of Guam and Tutuila in American Samoa, conversion of municipal solid waste to useable energy forms - principally electricity but possibly steam - may hold promise for reducing economic dependence on imported petroleum. A secondary benefit may be derived from reduction of solid waste landfill requirements. At the preliminary planning stage, waste-to-energy facilities producing electricity appear technically and environmentally feasible. Economically, the projects appear marginal but could be viable under specific conditions related to capital costs, revenue from garbage collection and revenue from the sale of the energy generated. Grant funding for the projects would considerably enhance the economic viability of the proposed facilities. The projects appear sufficiently viable to proceed to the detailed planning stage. Such projects are not viable for the islands now emerging from the US Trust Territory of the Pacific Islands.

  3. Feasibility study of internal conversion electron spectroscopy of {sup 229m}Th

    Energy Technology Data Exchange (ETDEWEB)

    Seiferle, Benedict; Wense, Lars von der; Thirolf, Peter G. [Ludwig-Maximilians-Universitaet Muenchen, Garching (Germany)

    2017-05-15

    With an expected energy of 7.8(5) eV, the isomeric first excited state in {sup 229}Th exhibits the lowest excitation energy of all known nuclei. Until today, a value for the excitation energy has been inferred only by indirect measurements. In this paper we propose an experimental method that is potentially capable of measuring the ground-state transition energy via the detection of the internal conversion electrons. MatLab-based Monte Carlo simulations have been performed to obtain an estimate of the expected statistics and to test the feasibility and the expected precision of the experiment. From the simulations we conclude that with the presented methods an energy determination with a precision of better than 0.1 eV is within reach. (orig.)

  4. Radioactive (14C) tracer studies of methanol conversion over a Ni-ZSM-5 zeolite

    International Nuclear Information System (INIS)

    Hwu, F.S.; Hightower, J.W.

    1983-01-01

    Secondary reactions have been identified in the overall conversion of methanol to hydrocarbons over a Ni-ZSM-5 catalyst. The major conclusions are: (1) The alkylation of light olefins with methanol or methyl ether is one pathway for the formation of larger olefins with one more carbon atom. (2) Paraffins are produced primarily by hydrogen transfer to the corresponding olefin. (3) Except for minor cracking reactions, paraffins with no more than 7 carbon atoms, are final stable products; isomerization among paraffin isomers does not take place at 368 0 C. (4) Light olefins, e.g. ethylene, propylene, and butenes, are reactive intermediates for aromatics formation. (5) Aromatic compounds may also be produced by methanol- methyl ether-alkylation of benzene and subsequent alkylated benezenes. 2 figures, 3 tables

  5. Comparative theology: an alternative to religious studies or theology of religions?

    OpenAIRE

    Avcı, Betül

    2018-01-01

    Avcı, Betül (IHU Author) This paper examines the relationship between Comparative Theology, Religious Studies and Theology of Religions and questions whether Comparative Theology is an alternative to the last two. Comparative Theology, a faith seeking understanding practice, may be viewed as an alternative to the Enlightenment ideal of Religious Studies, which seeks “impartiality” and “scientific objectivity” in contrast to Comparative Theology’s enquiry into “truth” and “meaning.” I sugge...

  6. Experimental Study of Heat Transfer Enhancements from Array of Alternate Rectangular Dwarf Fins at Different Inclinations

    Science.gov (United States)

    Awasarmol, Umesh Vandeorao; Pise, Ashok T.

    2018-02-01

    The main objective of this experimental work is to investigate and compare heat transfer enhancement of alternate dwarf fin array at different angles of inclination. In this study, the steady state heat transfer from the full length fin arrays and alternate dwarf fin arrays are measured in natural convection and radiation environment. Largest increase in the Nusselt number was achieved with alternate dwarf fin at angle of orientation 90°, which shows about 28% enhanced heat transfer coefficient as opposed to the full-length fin array with 25% saving in material. In case of non-black FAB, contribution of radiation heat transfer is found to be very small nearly within 1% of the heater input. After coating lamp black contribution of radiation heat transfer is found to increase to about 3-4% of the heater input in the range of temperatures considered in this study.

  7. An Interpretive Study of Yosemite National Park Visitors' Perspectives Toward Alternative Transportation in Yosemite Valley

    Science.gov (United States)

    White, Dave D.

    2007-01-01

    The National Park Service (NPS) is increasingly focusing on alternative transportation systems in national parks to address environmental and social problems arising from a historical reliance on personal automobiles as the primary means of visitor access. Despite the potential advantages, alternative transportation may require a reorientation in the way that Americans have experienced national parks since the advent of auto-tourism in the early twentieth century. Little research exists, however, on visitor perspectives towards alternative transportation or the rationale underlying their perspectives. It remains unclear how transportation systems affect visitors’ experiences of the park landscape or the factors influencing their travel behavior in the parks. This report presents an interpretive study of visitor perspectives toward transportation management in the Yosemite Valley area of Yosemite National Park, California. Qualitative analysis of 160 semi-structured interviews identified individual psychological factors as well as situational influences that affect visitors’ behavior and perspectives. Individual psychological factors include perceived freedom, environmental values and beliefs, prior experience with Yosemite National Park and other national parks, prior experience with alternative transportation in national parks, and sensitivity to subjective perceptions of crowding. Situational factors included convenience, access, and flexibility of travel modes, as well as type of visit, type of group, and park use level. Interpretive communication designed to encourage voluntary visitor use of alternative transportation should focus on these psychological and situational factors. Although challenges remain, the results of this study suggest approaches for shaping the way Americans visit and experience their national parks to encourage environmental sustainability.

  8. Uranium conversion; Urankonvertering

    Energy Technology Data Exchange (ETDEWEB)

    Oliver, Lena; Peterson, Jenny; Wilhelmsen, Katarina [Swedish Defence Research Agency (FOI), Stockholm (Sweden)

    2006-03-15

    FOI, has performed a study on uranium conversion processes that are of importance in the production of different uranium compounds in the nuclear industry. The same conversion processes are of interest both when production of nuclear fuel and production of fissile material for nuclear weapons are considered. Countries that have nuclear weapons ambitions, with the intention to produce highly enriched uranium for weapons purposes, need some degree of uranium conversion capability depending on the uranium feed material available. This report describes the processes that are needed from uranium mining and milling to the different conversion processes for converting uranium ore concentrate to uranium hexafluoride. Uranium hexafluoride is the uranium compound used in most enrichment facilities. The processes needed to produce uranium dioxide for use in nuclear fuel and the processes needed to convert different uranium compounds to uranium metal - the form of uranium that is used in a nuclear weapon - are also presented. The production of uranium ore concentrate from uranium ore is included since uranium ore concentrate is the feed material required for a uranium conversion facility. Both the chemistry and principles or the different uranium conversion processes and the equipment needed in the processes are described. Since most of the equipment that is used in a uranium conversion facility is similar to that used in conventional chemical industry, it is difficult to determine if certain equipment is considered for uranium conversion or not. However, the chemical conversion processes where UF{sub 6} and UF{sub 4} are present require equipment that is made of corrosion resistant material.

  9. A study of core electron binding energies in technetium-99m complexes by internal conversion electron spectroscopy

    International Nuclear Information System (INIS)

    Burke, J.F.; Archer, C.M.; Wei Chiu, K.; Latham, I.A.; Egdell, R.G.

    1991-01-01

    Core electron binding energies in a series of 99m Tc complexes have been studied by internal conversion electron spectroscopy (ICES) in a conventional x-ray photoelectron spectrometer. In both 3d and 3p regions, a chemical shift of about 1 eV is observed per unit increase in oxidation state. The role of ICES in characterizing radiopharmaceutical agents is illustrated with studies of some novel 99m Tc-phosphine complexes that have been developed for myocardial perfusion imaging. (author)

  10. Studies on the Effect of Radio Frequency Field in a Cusp-Type Charge Separation Device for Direct Energy Conversion

    OpenAIRE

    HAMABE, Masaki; IZAWA, Hiroaki; TAKENO, Hiromasa; NAKAMOTO, Satoshi; ICHIMURA, Kazuya; NAKASHIMA, Yousuke

    2016-01-01

    In D-3He fusion power generation, an application of direct energy conversion is expected in which separation of charged particles is necessary. A cusp-type direct energy converter (CuspDEC) was proposed as a charge separation device, but its performance was degraded for a high density plasma. The goal of the present study is to establish an additional method to assist charge separation by using a nonlinear effect of a radio frequency (rf) electric field. Following to the previous study, we ex...

  11. Comparative study on Ti/Zr/V and chromate conversion treated aluminum alloys: Anti-corrosion performance and epoxy coating adhesion properties

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Wen; Li, Wenfang, E-mail: mewfli@163.com; Mu, Songlin; Fu, Nianqing; Liao, Zhongmiao

    2017-05-31

    Highlights: • The surface roughness and surface free energy of the AA6063 are significantly increased after TZVCC treatment. • The anti-corrosion performance of the AA6063 is effectively enhanced after TZVCC treatment. • Both the corrosion resistance and wet adhesion properties of the epoxy coating on the AA6063 are noticeably improved after TZVCC treatment. - Abstract: In this study, a Ti/Zr/V conversion coating (TZVCC) was deposited on the surface of aluminum alloy 6063 (AA6063) as an alternative of the chromate conversion coating (CCC). Both the TZVCC treated AA6063 (TZVCC/AA6063) and CCC treated AA6063 (CCC/AA6063) were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), atomic force microscope (AFM) and contact angle measuring device. The anti-corrosion performance of the TZVCC/AA6063 and CCC/AA6063 was evaluated by electrochemical measurements and neutral salt spray tests. It showed that both the surface roughness and surface free energy of the AA6063 were significantly increased after TZVCC treatment. The anti-corrosion performance of TZVCC/AA6063 was superior to that of CCC/AA6063. In addition, the effects of the TZVCC and CCC on the adhesion properties and anti-corrosion performance of epoxy coating applied on samples were examined by pull-off tests and electrochemical impedance spectroscopy (EIS). The dry, wet and recovery adhesive strengths of the epoxy coating on TZVCC treated samples (epoxy coated TZVCC/AA6063) were very close to those of epoxy coating on CCC treated ones (epoxy coated CCC/AA6063). The epoxy coated TZVCC/AA6063 showed better corrosion resistance than the epoxy coated CCC/AA6063 and epoxy coated AA6063.

  12. Study on the conversion of H2 and CO from the helium carrier gas of high temperature gas-cooled reactor

    International Nuclear Information System (INIS)

    Liao Cuiping; Zheng Zhenhong; Shi Fuen

    1995-01-01

    The conversions of hydrogen and carbon monoxide into water vapor and carbon dioxide on CuO-ZnO-Al 2 O 3 catalyst are studied. The effects of different temperature, system atmospheric pressure, impurity gas concentration, flow and dew point on properties of cupric oxide bed are investigated. The conversion characteristics curves of H 2 and CO are given. Experimental data of conversion capacity, action period and conversion efficiency of CuO-ZnO-Al 2 O 3 are obtained and the optimal parameters are determined. The results show that the concentration of H 2 and CO of the effluent gas after purification can reach below 2 x 10 -6 , respectively. So it can meet the demands of high temperature gas-cooled reactor and also provide optimal design parameters and reliable data for conversion of H 2 and CO on CuO-ZnO-Al 2 O 3 catalyst

  13. Potential for wind energy generation and conversion for rural application: a case study for Ada

    International Nuclear Information System (INIS)

    Ayensu, A.; Lawluv, H.

    2001-01-01

    One major indicator of achieving the goals of Vision 2020 is an increased energy use per head, which had a 1993 value of 93 koe (kilograms of oil equivalent) as compared to 299 koe for the least developed middle income nation, and 5,563 koe for Singapore. To satisfy this energy requirement, all potential sources of energy must be harnessed and most importantly, the private sector's involvement in off-grid electric power generation must be encouraged. A cost-benefit analysis, energy payback time and energy ratios have been determined to assess the potential of wind energy generation and conversation at Ada; which has a mean monthly wind speed of 6.23 m/s at a height of 30 m and considered to be adequate to run a small to medium sized wind turbine to generate about 28 kW. The proposal is to install a prototype aero generation system for a small community isolated from the national grid line, and is aimed at demonstrating how a renewable, non-pollutant and independent power source, transformed by means of advanced technology can achieve energy self sufficiency for the community, while avoiding negative impacts on the environment and ensuring cost-effectiveness. The system will consist of an aero-generation unit, storage system and demand electric consumption. The generator will supply the power to batteries through a load rectifier/governor for storage. The demand in electric consumption can be supplied in DC by accumulators or AC by current inverter. The technical features proposed for the aero generation system is a 20 - 30 kW maximum power turbine, a 24 V capacity battery delivery 1625 Ah in 100 h, two charger inverter units connected in parallel with AC synchronized outlet for consumption. The outlet power of each inverter will be 2400 W DC and the estimated time to complete battery load power unit will be 12 h. The projected cost of electricity generated by an optimized scheme is estimated to be 9 cents/kWh, as compared with photovoltaic generation at 5 - 14

  14. A Study of the Effect of Alternative Programs on the Potential Dropout.

    Science.gov (United States)

    Gloria, Cyril; Karr-Kidwell, PJ

    Educators are very concerned about the problem of students dropping out of school. The reasons for students dropping out vary from social to economic causes. Alternative programs or schools have been used since the 1960s to try to keep students in school. This study involved a literature review of research on the identification and remediation of…

  15. Fourth "R" in Analytic Mode: A Study of Alternatives to Religious Instruction in the Public Schools.

    Science.gov (United States)

    Dudley, Noel W.

    This doctoral dissertation examines alternatives for public-school religious education which stress spiritual values but do not conflict with legal restrictions. The study is divided into four parts. Part one is an historical survey of religious education in public schools that includes an interpretation of the legal restrictions and the…

  16. FOCUSED FEASIBILITY STUDY OF PHYTOREMEDIATION ALTERNATIVE FOR THE INDUSTRIAL EXCESS LANDFILL SITE IN STARK COUNTY, OHIO.

    Science.gov (United States)

    Focused feasibility study of phytoremediation alternative for the Industrial Excess Landfill site in Stark County, Ohio. More information can be found on the NPL Fact Sheet for this site at www.epa.gov/region5/superfund/npl/ohio/OHD000377971.htm

  17. Coupling Cover Crops with Alternative Swine Manure Application Strategies: Manure-15N Tracer Studies

    Science.gov (United States)

    Integration of rye cover crops with alternative liquid swine (Sus scrofa L.) manure application strategies may enhance retention of manure N in corn (Zea mays L.) - soybean [Glycine max (L.) Merr] cropping systems. The objective of this study was to quantify uptake of manure derived-N by a rye (Seca...

  18. Alternative Conceptions in Animal Classification Focusing on Amphibians and Reptiles: A Cross-Age Study

    Science.gov (United States)

    Yen, Chiung-Fen; Yao, Tsung-Wei; Chiu, Yu-Chih

    2004-01-01

    This study examined students' alternative conceptions of reptiles and amphibians and the extent to which these conceptions remain intact through the elementary (grades 4 and 6), junior, and senior high school years. We administered multiple-choice and free-response instruments to a total of 513 students and interviewed at least 20 students at each…

  19. Final cost reduction study for the Geysers Recharge Alternative. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    The purpose of this study is to determine whether or not cost reduction opportunities exist for the Geysers Recharge Alternative as defined in the Santa Rosa Subregional Long-Term Wastewater Project EIR/EIS. The City of Santa Rosa has been directed to have a plan for reclaimed water disposal in place by 1999 which will meet future capacity needs under all weather conditions. A Draft EIR/EIS released in July 1996 and a Final EIR certified in June 1997 examine four primary alternatives plus the No Action Alternative. Two of the primary alternatives involve agricultural irrigation with reclaimed water, either in western or southern Sonoma County. Another involves increased discharge of reclaimed water into the Russian River. The fourth involves using reclaimed water to replenish the geothermal reservoir at the Geysers. The addition of this water source would enable the Geysers operators to produce more steam from the geothermal area and thereby prolong the life and economic production level of the steamfield and the geothermal power plants supplied by the steamfield. This study provides additional refined cost estimates for new scenarios which utilize an alternative pipeline alignment and a range of reclaimed water flows, which deliver less water to the Geysers than proposed in the EIR/EIS (by distributing flow to other project components). Also, electrical power rates were revised to reflect the recent changes in costs associated with deregulation of the power industry. In addition, this report provides information on sources of potential public and private funding available and future environmental documentation required if the cost reduction scenarios were to be selected by the City as part of their preferred alternative.

  20. Study of the Corrosion Resistance of Austenitic Stainless Steels during Conversion of Waste to Biofuel

    Science.gov (United States)

    Cabrini, Marina; Lorenzi, Sergio; Pastore, Tommaso; Pellegrini, Simone; Burattini, Mauro; Miglio, Roberta

    2017-01-01

    The paper deals with the corrosion behavior of stainless steels as candidate materials for biofuel production plants by liquefaction process of the sorted organic fraction of municipal solid waste. Corrosion tests were carried out on AISI 316L and AISI 304L stainless steels at 250 °C in a batch reactor during conversion of raw material to bio-oil (biofuel precursor), by exposing specimens either to water/oil phase or humid gas phase. General corrosion rate was measured by weight loss tests. The susceptibility to stress corrosion cracking was evaluated by means of U-bend specimens and slow stress rate tests at 10−6 or 10−5 s−1 strain rate. After tests, scanning electron microscope analysis was carried out to detect cracks and localized attacks. The results are discussed in relation with exposure conditions. They show very low corrosion rates strictly dependent upon time and temperature. No stress corrosion cracking was observed on U-bend specimens, under constant loading. Small cracks confined in the necking cone of specimens prove that stress corrosion cracking only occurred during slow strain rate tests at stresses exceeding the yield strength. PMID:28772682

  1. Studies on the induction of mitotic gene conversion by ultraviolet irradiation

    International Nuclear Information System (INIS)

    Ito, T.; Kobayashi, K.

    1975-01-01

    The UV (270-nm) dose-frequency relationship for the induction of intragenic mitotic recombination at trp 5 locus in Saccharomyces cerevisiae was non-linear. Two parameters, α and a, in the proposed equation for the non-linear relationship f = (at)α were determined so as to fit the experimental data by the method of least squares. The analysis was extended over 5 cell stages during synchronous growth. It was found that (1) parameter α changed from 2.02 for unbudded small cells to 1.09 for the stage where the cell had finished the division of the nucleus, and (2) parameter a changed correspondingly from 7.25.10 -4 to 0.180.10- 4 sec -1 during the same period. One interesting outcome in this analysis was the deduction of a dose-dependent nature of relative sensitivity with respect to the stage. The determination of these two parameters enabled us to calculate dose-effect relationships beyond the limits of experimental restrictions. Such an ''imaginary'' relationship, calculated at an extremely low dose, revealed the existence of maximal sensitivity around the DNA synthesis period. It was further shown that this maximum would easily be masked even in the moderate dose range. Thus, we conclude that the validity of single dose comparisons is diminished unless α is constant regardless of the cell stage. Some considerations on the proposed parameters have been made in relation to the mechanisms of the induction of gene conversion by UV

  2. Study of Syngas Conversion to Light Olefins by Response Surface Methodology

    Directory of Open Access Journals (Sweden)

    Hossein Atashi

    2013-01-01

    Full Text Available The effect of adding MgO to a precipitated iron-cobalt-manganese based Fischer-Tropsch synthesis (FTS catalyst was investigated via response surface methodology. The catalytic performance of the catalysts was examined in a fixed bed microreactor at a total pressure of 1–7 bar, temperature of 280–380°C, MgO content of 5–25% and using a syngas having a H2 to CO ratio equal to 2.The dependence of the activity and product distribution on MgO content, temperature, and pressure was successfully correlated via full quadratic second-order polynomial equations. The statistical analysis and response surface demonstrations indicated that MgO significantly influences the CO conversion and chain growth probability as well as ethane, propane, propylene, butylene selectivity, and alkene/alkane ratio. A strong interaction between variables was also evidenced in some cases. The decreasing effect of pressure on alkene to alkane ratio is investigated through olefin readsorption effects and CO hydrogenation kinetics. Finally, a multiobjective optimization procedure was employed to calculate the best amount of MgO content in different reactor conditions.

  3. Specialist inpatient treatment for severe motor conversion disorder: a retrospective comparative study.

    Science.gov (United States)

    McCormack, Ruaidhri; Moriarty, John; Mellers, John D; Shotbolt, Paul; Pastena, Rosa; Landes, Nadine; Goldstein, Laura; Fleminger, Simon; David, Anthony S

    2014-08-01

    Gold standard protocols have yet to be established for the treatment of motor conversion disorder (MCD). There is limited evidence to support inpatient, multidisciplinary intervention in chronic, severe cases. To evaluate the characteristics and outcomes of MCD patients admitted to a specialist neuropsychiatric inpatient unit. All patients admitted to the Lishman Unit (years 2007-2011) with a diagnosis of MCD were included. Data relevant to characteristics and status with regard to mobility, activities of daily living (ADLs) and Modified Rankin Scale (MRS) score at admission and discharge were extracted. Thirty-three cases (78.8% female) were included; the median duration of illness was 48 months. In comparison with brain injury patients admitted to the same unit, more cases had histories of childhood sexual abuse (36.4%, n=12), premorbid non-dissociative mental illness (81.1%, n=27) and employment as a healthcare/social-care worker (45.5%, n=15). Cases showed significant improvements in MRS scores (p<0.001), mobility (p<0.001) and ADL (p=0.002) following inpatient treatment. Patients with severe, long-standing MCD can achieve significant improvements in functioning after admission to a neuropsychiatry unit. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  4. ICRF Mode Conversion Studies with Phase Contrast Imaging and Comparisons with Full-Wave Simulations

    International Nuclear Information System (INIS)

    Tsujii, N.; Bonoli, P. T.; Lin, Y.; Wright, J. C.; Wukitch, S. J.; Porkolab, M.; Jaeger, E. F.; Harvey, R. W.

    2011-01-01

    Waves in the ion cyclotron range of frequencies (ICRF) are widely used to heat toka-mak plasmas. In a multi-ion-species plasma, the FW converts to ion cyclotron waves (ICW) and ion Bernstein waves (IBW) around the ion-ion hybrid resonance (mode conversion). The mode converted wave is of interest as an actuator to optimise plasma performance through flow drive and current drive. Numerical simulations are essential to describe these processes accurately, and it is important that these simulation codes be validated. On Alcator C-Mod, direct measurements of the mode converted waves have been performed using Phase Contrast Imaging (PCI), which measures the line-integrated electron density fluctuations. The results were compared to full-wave simulations AORSA and TORIC. AORSA is coupled to a Fokker-Planck code CQL3D for self-consistent simulation of the wave electric field and the minority distribution function. The simulation results are compared to PCI measurements using synthetic diagnostic. The experiments were performed in D-H and D- 3 He plasmas over a wide range of ion species concentrations. The simulations agreed well with the measurements in the strong absorption regime. However, the measured fluctuation intensity was smaller by 1-2 orders of magnitudes in the weakly abosorbing regime, and a realistic description of the plasma edge including dissipation and antenna geometry may be required in these cases.

  5. Digital computer study of nuclear reactor thermal transients during startup of 60-kWe Brayton power conversion system

    Science.gov (United States)

    Jefferies, K. S.; Tew, R. C.

    1974-01-01

    A digital computer study was made of reactor thermal transients during startup of the Brayton power conversion loop of a 60-kWe reactor Brayton power system. A startup procedure requiring the least Brayton system complication was tried first; this procedure caused violations of design limits on key reactor variables. Several modifications of this procedure were then found which caused no design limit violations. These modifications involved: (1) using a slower rate of increase in gas flow; (2) increasing the initial reactor power level to make the reactor respond faster; and (3) appropriate reactor control drum manipulation during the startup transient.

  6. Cognitive-analytical therapy for a patient with functional neurological symptom disorder-conversion disorder (psychogenic myopia: A case study

    Directory of Open Access Journals (Sweden)

    Hamid Nasiri

    2015-01-01

    Full Text Available Functional neurological symptom disorder commonly presents with symptoms and defects of sensory and motor functions. Therefore, it is often mistaken for a medical condition. It is well known that functional neurological symptom disorder more often caused by psychological factors. There are three main approaches namely analytical, cognitive and biological to manage conversion disorder. Any of such approaches can be applied through short-term treatment programs. In this case, study a 12-year-old boy with the diagnosed functional neurological symptom disorder (psychogenic myopia was put under a cognitive-analytical treatment. The outcome of this treatment modality was proved successful.

  7. Cognitive-analytical therapy for a patient with functional neurological symptom disorder-conversion disorder (psychogenic myopia): A case study.

    Science.gov (United States)

    Nasiri, Hamid; Ebrahimi, Amrollah; Zahed, Arash; Arab, Mostafa; Samouei, Rahele

    2015-05-01

    Functional neurological symptom disorder commonly presents with symptoms and defects of sensory and motor functions. Therefore, it is often mistaken for a medical condition. It is well known that functional neurological symptom disorder more often caused by psychological factors. There are three main approaches namely analytical, cognitive and biological to manage conversion disorder. Any of such approaches can be applied through short-term treatment programs. In this case, study a 12-year-old boy with the diagnosed functional neurological symptom disorder (psychogenic myopia) was put under a cognitive-analytical treatment. The outcome of this treatment modality was proved successful.

  8. Alternative Education: A Comparative Case Study of the Behavior Modification Programs of Two Upstate South Carolina Alternative Schools for Youth Who Exhibit Behavior That Is Disruptive

    Science.gov (United States)

    Scipio, Timothy Lamont

    2013-01-01

    This study examined behavior modification programs in schools designed to focus on discipline and that aim to reform disruptive behavior in students, usually over a limited period of time. This was a comparative case study of two type II alternative schools in the Upstate of South Carolina. The findings contributed to the research base regarding…

  9. Ethnographic Observational Study of the Biologic Initiation Conversation Between Rheumatologists and Biologic-Naive Rheumatoid Arthritis Patients.

    Science.gov (United States)

    Kottak, Nicholas; Tesser, John; Leibowitz, Evan; Rosenberg, Melissa; Parenti, Dennis; DeHoratius, Raphael

    2018-01-30

    This ethnographic market research study investigated the biologic initiation conversation between rheumatologists and biologic-naive patients with rheumatoid arthritis to assess how therapy options, particularly mode of administration, were discussed. Consenting rheumatologists (n = 16) and patients (n = 48) were videotaped during medical visits and interviewed by a trained ethnographer. The content, structure, and timing of conversations regarding biologic initiation were analyzed. The mean duration of physician-patient visits was approximately 15 minutes; biologic therapies were discussed for a mean of 5.6 minutes. Subcutaneous (SC) and intravenous (IV) therapy options were mentioned in 45 and 35 visits, respectively, out of a total of 48 visits. All patients had some familiarity with SC administration, but nearly half of patients (22 of 48) were unfamiliar with IV therapy going into the visit. IV administration was not defined or described by rheumatologists in 77% of visits (27 of 35) mentioning IV therapy. Thus, 19 of 22 patients who were initially unfamiliar with IV therapy remained unfamiliar after the visit. Disparities in physician-patient perceptions were revealed, as all rheumatologists (16 of 16) believed IV therapy would be less convenient than SC therapy for patients, while 46% of patients (22 of 48) felt this way. In post-visit interviews, some patients seemed confused and overwhelmed, particularly when presented with many treatment choices in a visit. Some patients stated they would benefit from visual aids or summary sheets of key points. This study revealed significant educational opportunities to improve the biologic initiation conversation and indicated a disparity between patients' and rheumatologists' perception of IV therapy. © 2018 The Authors. Arthritis Care & Research published by Wiley Periodicals, Inc. on behalf of American College of Rheumatology.

  10. ALTERNATIVE DISPUTE RESOLUTION IN BANYUMAS REGENCY: IN THE PERSPECTIVE OF CULTURAL STUDIES

    Directory of Open Access Journals (Sweden)

    Singkir Hudijono

    2012-11-01

    Full Text Available This study discusses about an Alternative Dispute Resolution in BanyumasRegency as a non-litigation dispute resolution. The problem observed was a breakthroughtaken by the Society in Banyumas Regency in overcoming the so far deadlock of lawenforcement and the attitude of not trusting the justice enforcement. It has been a publicsecret that the dispute resolutions employing the legal centralism paradigm have beendominated by the judicial network. This has caused the acknowledgement of the state lawto decrease, being a commodity that can be traded. The research aims at finding out anddescribing how the alternative dispute resolution (ADR emerges as an alternativemechanism in deconstructing the legal centralism; interpreting and describing what ismeant by the alternative dispute resolution (ADR in the development of progressive law.This research was conducted employing qualitative method. In this context, theresearcher explored various pieces of related information with the reason that the societyin Banyumas Regency has chosen the alternative dispute resolution mechanism as themechanism in deconstructing the legal centralism. The research was conducted asfollows: the problems were identified, the theories for analyzing the data were selected,the primary and secondary data were collected, the collected data were analyzed andinterpreted, and finally, the results of the research were written and constructed. Thetheories employed were critical legal studies, deconstruction, and large narration criticismtheories.The results of the research show that: firstly, the alternative dispute resolution hasemerged because of the awakened local knowledge, as the form of anticipation to theineffective formal law domination. With regard to the effect of global intercourse, thealternative dispute resolution has emerged because of the refusal against the culturalhomogeneity. Secondly, the implementation of the alternative dispute resolution hasbecome the preferred

  11. Conversational flow promotes solidarity.

    Science.gov (United States)

    Koudenburg, Namkje; Postmes, Tom; Gordijn, Ernestine H

    2013-01-01

    Social interaction is fundamental to the development of various aspects of "we-ness". Previous research has focused on the role the content of interaction plays in establishing feelings of unity, belongingness and shared reality (a cluster of variables referred to as solidarity here). The present paper is less concerned with content, but focuses on the form of social interaction. We propose that the degree to which conversations flow smoothly or not is, of itself, a cue to solidarity. We test this hypothesis in samples of unacquainted and acquainted dyads who communicate via headsets. Conversational flow is disrupted by introducing a delay in the auditory feedback (vs. no delay). Results of three studies show that smoothly coordinated conversations (compared with disrupted conversations and a control condition) increase feelings of belonging and perceptions of group entitativity, independently of conversation content. These effects are driven by the subjective experience of conversational flow. Our data suggest that this process occurs largely beyond individuals' control. We conclude that the form of social interaction is a powerful cue for inferring group solidarity. Implications for the impact of modern communication technology on developing a shared social identity are discussed.

  12. Conversational flow promotes solidarity.

    Directory of Open Access Journals (Sweden)

    Namkje Koudenburg

    Full Text Available Social interaction is fundamental to the development of various aspects of "we-ness". Previous research has focused on the role the content of interaction plays in establishing feelings of unity, belongingness and shared reality (a cluster of variables referred to as solidarity here. The present paper is less concerned with content, but focuses on the form of social interaction. We propose that the degree to which conversations flow smoothly or not is, of itself, a cue to solidarity. We test this hypothesis in samples of unacquainted and acquainted dyads who communicate via headsets. Conversational flow is disrupted by introducing a delay in the auditory feedback (vs. no delay. Results of three studies show that smoothly coordinated conversations (compared with disrupted conversations and a control condition increase feelings of belonging and perceptions of group entitativity, independently of conversation content. These effects are driven by the subjective experience of conversational flow. Our data suggest that this process occurs largely beyond individuals' control. We conclude that the form of social interaction is a powerful cue for inferring group solidarity. Implications for the impact of modern communication technology on developing a shared social identity are discussed.

  13. Methodological aspects of market study on residential, commercial and industrial sectors, of the Conversion Project for natural gas of existing network in Sao Paulo city

    International Nuclear Information System (INIS)

    Kishinami, R.I.; Perazza, A.A.

    1991-01-01

    The methodological aspects of market study, developed at the geographical area served by existing network of naphtha gas, which will be converted to natural gas in a two years conversion program are presented. (author)

  14. Study on high conversion type core of innovative water reactor for flexible fuel cycle (FLWR) for minor actinide (MA) recycling

    International Nuclear Information System (INIS)

    Fukaya, Yuji; Nakano, Yoshihiro; Okubo, Tsutomu

    2009-01-01

    In order to ensure sustainable energy supplies in the future based on the well-established light water reactor (LWR) technologies, conceptual design studies have been performed on the innovative water reactor for flexible fuel cycle (FLWR) with the high conversion ratio core. For early introduction of FLWR without a serious technical gap from the LWR technologies, the conceptual design of the high conversion type one (HC-FLWR) was constructed to recycle reprocessed plutonium. Furthermore, an investigation of minor actinide (MA) recycling based on the HC-FLWR core concept has been performed and is presented in this paper. Because HC-FLWR is a near-term technology, it would be a good option in the future if HC-FLWR can recycle MAs. In order to recycle MAs in HC-FLWR, it has been found that the core design should be changed, because the loaded MA makes the void reactivity coefficient worse and decreases the discharge burn-up. To find a promising core design specification, the investigation on the core characteristics were performed using the results from parameter surveys with core burn-up calculations. The final core designs were established by coupled three dimensional neutronics and thermal-hydraulics core calculations. The major core specifications are as follows. The plutonium fissile (Puf) content is 13 wt%. The discharge burn-up is about 55 GWd/t. Around 2 wt% of Np or Am can be recycled. The MA conversion ratios are around unity. In particular, it has been found that loaded Np can be transmuted effectively in this core concept. Therefore, these concepts would be a good option to reduce environmental burdens.

  15. [Conversation analysis for improving nursing communication].

    Science.gov (United States)

    Yi, Myungsun

    2007-08-01

    Nursing communication has become more important than ever before because quality of nursing services largely depends on the quality of communication in a very competitive health care environment. This article was to introduce ways to improve nursing communication using conversation analysis. This was a review study on conversation analysis, critically examining previous studies in nursing communication and interpersonal relationships. This study provided theoretical backgrounds and basic assumptions of conversation analysis which was influenced by ethnomethodology, phenomenology, and sociolinguistic. In addition, the characteristics and analysis methods of conversation analysis were illustrated in detail. Lastly, how conversation analysis could help improve communication was shown, by examining researches using conversation analysis not only for ordinary conversations but also for extraordinary or difficult conversations such as conversations between patients with dementia and their professional nurses. Conversation analysis can help in improving nursing communication by providing various structures and patterns as well as prototypes of conversation, and by suggesting specific problems and problem-solving strategies in communication.

  16. Theoretical studies aiming at the IEA-R1 reactor core conversion from high U-235 enrichment to low U-235 enrichment

    International Nuclear Information System (INIS)

    Frajndlich, R.

    1982-01-01

    The research reactors, of which the fuel elements are of MTR type, functions presently, almost in their majority with high U-235 enrichment. The fear that those fuel elements might generate a considerabLe proliferation of nuclear weapons rendered almost mandatory the conversion of highly enriched fuel elements to a low U-235 enrichment. As the IEA-R1 reactor of IPEN is operating with highly enriched fuel elements a study aiming at this conversion was done. The problems related to the conversion and the results obtained, demonstrated the technical viabilty for its realization. (E.G.) [pt

  17. Use of alternative medicine for hypertension in Buikwe and Mukono districts of Uganda: a cross sectional study.

    Science.gov (United States)

    Nuwaha, Fred; Musinguzi, Geofrey

    2013-11-04

    Use of alternative medicine for chronic diseases such as hypertension is common in low as well as high income countries. This study estimated the proportion of people who were aware of their hypertension that use alternative medicine and identified factors predicting the use of alternative medicine. In a community based cross sectional survey among people ≥ 15 years in Buikwe and Mukono districts of Uganda 258 people aware of their hypertension were questioned about use of alternative medicine for hypertension, advice about uptake of life style intervention for hypertension control such as reduction of salt intake and about their attitude towards use of alternative medicine. Proportions of people who used alternative medicine and adopt life style interventions and their 95% confidence intervals (CI) were calculated. Predictors of using alternative medicine were identified using logistic binary regression analysis. More than a half 144 (56.2%) had ever used alternative medicine whereas more than one in four 74 (28.6%) were currently using alternative medicine alone or in combination with modern medicine (50%). People who were using alternative medicine alone (29.7% CI 17.5-45.9) were less likely to have received advice on reduction of salt intake compared to those using modern medicine alone or in combination with traditional medicine (56.6%, CI 47.7-65.0). The only independent predictor for using alternative medicine was agreeing that alternative medicine is effective for treatment of hypertension (adjusted odds ratio [AOR] 2.6; 95% CI 1.40-4.82). The use of alternative medicine was common among patients with hypertension and usage was underpinned by the belief that alternative medicine is effective. As patients with hypertension use alternative medicine and modern medicine concurrently, there is need for open communication between health workers and patients regarding use of alternative medicine.

  18. Life cycle assessment of the use of alternative fuels in cement kilns: A case study.

    Science.gov (United States)

    Georgiopoulou, Martha; Lyberatos, Gerasimos

    2018-06-15

    The benefits of using alternative fuels (AFs) in the cement industry include reduction of the use of non-renewable fossil fuels and lower emissions of greenhouse gases, since fossil fuels are replaced with materials that would otherwise be degraded or incinerated with corresponding emissions and final residues. Furthermore, the use of alternative fuels maximizes the recovery of energy. Seven different scenaria were developed for the production of 1 ton of clinker in a rotary cement kiln. Each of these scenaria includes the use of alternative fuels such as RDF (Refuse derived fuel), TDF (Tire derived fuel) and BS (Biological sludge) or a mixture of them, in partial replacement of conventional fuels such as coal and pet coke. The purpose of this study is to evaluate the environmental impacts of the use of alternative fuels in relation to conventional fuels in the kiln operation. The Life Cycle Assessment (LCA) methodology is used to quantify the potential environmental impacts in each scenario. The interpretation of the results provides the conclusion that the most environmentally friendly prospect is the scenario based on RDF while the less preferable scenario is the scenario based on BS. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. B cell remote-handled waste shipment cask alternatives study; TOPICAL

    International Nuclear Information System (INIS)

    RIDDELLE, J.G.

    1999-01-01

    The decommissioning of the 324 Facility B Cell includes the onsite transport of grouted remote-handled radioactive waste from the 324 Facility to the 200 Areas for disposal. The grouted waste has been transported in the leased ATG Nuclear Services 3-82B Radioactive Waste Shipping Cask (3-82B cask). Because the 3-82B cask is a U.S. Nuclear Regulatory Commission (NRC)-certified Type B shipping cask, the lease cost is high, and the cask operations in the onsite environment may not be optimal. An alternatives study has been performed to develop cost and schedule information on alternative waste transportation systems to assist in determining which system should be used in the future. Five alternatives were identified for evaluation. These included continued lease of the 3-82B cask, fabrication of a new 3-82B cask, development and fabrication of an onsite cask, modification of the existing U.S. Department of Energy-owned cask (OH-142), and the lease of a different commercially available cask. Each alternative was compared to acceptance criteria for use in the B Cell as an initial screening. Only continued leasing of the 3-82B cask, fabrication of a new 3-82B cask, and the development and fabrication of an onsite cask were found to meet all of the B Cell acceptance criteria

  20. An observational study evaluating tacrolimus dose, exposure, and medication adherence after conversion from twice- to once-daily tacrolimus in liver and kidney transplant recipients.

    Science.gov (United States)

    Bäckman, Lars; Persson, Carl-Axel

    2014-03-17

    Immunosuppression regimens in transplantation medicine are complex. Drugs with extended release action have simplified medication dosing without affecting efficacy. This prospective, observational, multicenter study, conducted in a routine medical practice setting, evaluated changes in tacrolimus daily dose and trough levels and patient-reported medication adherence at day 90 after 1:1 (mg: mg) conversion to once-daily tacrolimus in adult liver and kidney transplant recipients. Data from 224 recipients of a liver (n=19) or kidney (n=205) transplant, average age 51±14.5 years, were evaluated. The mean change in tacrolimus daily dose was +0.04 mg/day. Dose remained stable after conversion in 62.5%, was lower in 15.6%, and higher in 22% of patients. Trough level after conversion was lower in 62.6% and higher in 36.5%; generally, levels were 12.8% lower than pre-conversion levels. No acute rejection, graft loss, or serious safety events were observed. Two deaths occurred due to myocardial infarction. Conversion helped 19% to less frequently forget medications and 55% reported no difference in remembering to take the once-daily dose after conversion. The change in dosing frequency was identified as "better" for 55%. Tacrolimus daily dose remained stable while trough levels were significantly lower after conversion to once-daily dosing. Safety and efficacy were maintained; reduced dosing frequency had no apparent influence on patient-reported medication adherence.

  1. Photovoltaic conversion of laser energy

    Science.gov (United States)

    Stirn, R. J.

    1976-01-01

    The Schottky barrier photovoltaic converter is suggested as an alternative to the p/n junction photovoltaic devices for the conversion of laser energy to electrical energy. The structure, current, output, and voltage output of the Schottky device are summarized. The more advanced concepts of the multilayer Schottky barrier cell and the AMOS solar cell are briefly considered.

  2. Absorption spectroscopic studies of carbon dioxide conversion in a low pressure glow discharge using tunable infrared diode lasers

    International Nuclear Information System (INIS)

    Hempel, F; Roepcke, J; Miethke, F; Wagner, H-E

    2002-01-01

    The time and spatial dependence of the chemical conversion of CO 2 to CO were studied in a closed glow discharge reactor (p = 50 Pa, I = 2-30 mA) consisting of a small plasma zone and an extended stationary afterglow. Tunable infrared diode laser absorption spectroscopy has been applied to determine the absolute ground state concentrations of CO and CO 2 . After a certain discharge time an equilibrium of the concentrations of both species could be observed. The spatial dependence of the equilibrium CO concentration in the afterglow was found to be varying less than 10%. The feed gas was converted to CO more predominantly between 43% and 60% with increasing discharge current, forming so-called quasi-equilibrium states of the stable reaction products. The formation time of the stable gas composition also decreased with the current. For currents higher than 10 mA the conversion rate of CO 2 to CO was estimated to be 1.2x10 13 molecules J -1 . Based on the experimental results, a plasma chemical modelling has been established

  3. The emergency telephone conversation in the context of the older person in suicidal crisis: a qualitative study.

    Science.gov (United States)

    Deuter, Kate; Procter, Nicholas; Rogers, John

    2013-01-01

    Suicide in older people is a significant public health issue with a predicted future increase. Contemporary research directs considerable attention toward physical, mental, and social risk factors that contribute to suicidality in older people; still, little is understood about the fundamental meanings that older people in suicidal crisis attribute to these factors. The aim of this qualitative study was to describe, analyze, and compare counselors' and older peoples' perceptions of the suicidal crisis during an emergency telephone conversation. Data collection consisted of individual interviews with telephone counselors (N = 7) working within an emergency mental health triage service, and listening to telephone calls (N = 14) received by the service responding to people aged 65 years and over in suicidal crisis. Triangulation of the two data sets resulted in the emergence of three key themes. We found (1) congruence in the way risk factors were perceived by counselors and communicated during telephone conversations, (2) dissension between counselors' perceptions of end-of-life issues and older people's feelings of ambivalence about wanting to die and not knowing what to do and (3) the need for working side-by-side with the older person, exploring acute changes and immediate capacity for change. An explicit focus on risk factors alone may preclude counselors from gaining a deeper understanding of suicidal crisis in an older person's life. This research has begun to capture and illuminate how telephone counselors can deliver effective crisis intervention as older people struggle and make meaning through their suffering.

  4. [Neurology of hysteria (conversion disorder)].

    Science.gov (United States)

    Sonoo, Masahiro

    2014-07-01

    Hysteria has served as an important driving force in the development of both neurology and psychiatry. Jean Martin Charcot's devotion to mesmerism for treating hysterical patients evoked the invention of psychoanalysis by Sigmund Freud. Meanwhile, Joseph Babinski took over the challenge to discriminate between organic and hysterical patients from Charcot and found Babinski's sign, the greatest milestone in modern neurological symptomatology. Nowadays, the usage of the term hysteria is avoided. However, new terms and new classifications are complicated and inconsistent between the two representative taxonomies, the DSM-IV and ICD-10. In the ICD-10, even the alternative term conversion disorder, which was becoming familiar to neurologists, has also disappeared as a group name. The diagnosis of hysteria remains important in clinical neurology. Extensive exclusive diagnoses and over investigation, including various imaging studies, should be avoided because they may prolong the disease course and fix their symptoms. Psychological reasons that seem to explain the conversion are not considered reliable. Positive neurological signs suggesting nonorganic etiologies are the most reliable measures for diagnosing hysteria, as Babinski first argued. Hysterical paresis has several characteristics, such as giving-way weakness or peculiar distributions of weakness. Signs to uncover nonorganic paresis utilizing synergy include Hoover's test and the Sonoo abductor test.

  5. An Independent Evaluation of the FMEA/CIL Hazard Analysis Alternative Study

    Science.gov (United States)

    Ray, Paul S.

    1996-01-01

    The present instruments of safety and reliability risk control for a majority of the National Aeronautics and Space Administration (NASA) programs/projects consist of Failure Mode and Effects Analysis (FMEA), Hazard Analysis (HA), Critical Items List (CIL), and Hazard Report (HR). This extensive analytical approach was introduced in the early 1970's and was implemented for the Space Shuttle Program by NHB 5300.4 (1D-2. Since the Challenger accident in 1986, the process has been expanded considerably and resulted in introduction of similar and/or duplicated activities in the safety/reliability risk analysis. A study initiated in 1995, to search for an alternative to the current FMEA/CIL Hazard Analysis methodology generated a proposed method on April 30, 1996. The objective of this Summer Faculty Study was to participate in and conduct an independent evaluation of the proposed alternative to simplify the present safety and reliability risk control procedure.

  6. Substance use and dietary practices among students attending alternative high schools: results from a pilot study

    OpenAIRE

    Arcan, Chrisa; Kubik, Martha Y; Fulkerson, Jayne A; Hannan, Peter J; Story, Mary

    2011-01-01

    Abstract Background Substance use and poor dietary practices are prevalent among adolescents. The purpose of this study was to examine frequency of substance use and associations between cigarette, alcohol and marijuana use and selected dietary practices, such as sugar-sweetened beverages, high-fat foods, fruits and vegetables, and frequency of fast food restaurant use among alternative high school students. Associations between multi-substance use and the same dietary practices were also exa...

  7. Emotional experiences predict the conversion of individuals with Attenuated Psychosis Syndrome to psychosis: A six-month follow up study

    Directory of Open Access Journals (Sweden)

    Fa Zhan Chen

    2016-06-01

    Full Text Available The present study explored the conversion rate in individuals with Attenuated Psychosis Syndrome (APS and potential predictor for transition in China. Sixty-three participants were identified as APS were followed up six months later. The results showed that 17% of individuals with APS converted to psychosis. The converters exhibited poorer emotional experience and expression than the non-converters at baseline. A further binary logistic regression analysis showed that emotional experience could predict the transition (Wald = 4.18, p = 0.041, 95% CI = 1.04~6.82. The current study suggested an important role of emotional processing in the prediction of the development of full-blown psychosis.

  8. Studies on the effect of radio frequency field in a cusp-type charge separation device for direct energy conversion

    International Nuclear Information System (INIS)

    Hamabe, Masaki; Izawa, Hiroaki; Takeno, Hiromasa; Nakamoto, Satoshi; Ichimura, Kazuya; Nakashima, Yousuke

    2016-01-01

    In D- 3 He fusion power generation, an application of direct energy conversion is expected in which separation of charged particles is necessary. A cusp-type direct energy converter (CuspDEC) was proposed as a charge separation device, but its performance was degraded for a high density plasma. The goal of the present study is to establish an additional method to assist charge separation by using a nonlinear effect of a radio frequency (rf) electric field. Following to the previous study, we experimentally examine the effect of an rf field to electron motion in a CuspDEC device. Two ring electrodes were newly installed in a CuspDEC simulator and the current flowing into the electron collector located in the line cusp region was measured on an rf field application. The significant variation in the current was found, and an improvement of the charge separation can be expected by using the phenomenon appropriately. (author)

  9. Collaborative study for the validation of alternative in vitro potency assays for human tetanus immunoglobulins.

    Science.gov (United States)

    Gross, S; Janssen, S W J; de Vries, B; Terao, E; Daas, A; Buchheit, K-H

    2010-07-01

    An international collaborative study to validate 2 alternative in vitro methods for the potency testing of human tetanus immunoglobulin products was organised by the European Directorate for the Quality of Medicines & HealthCare (EDQM). The study, run in the framework of the Biological Standardisation Programme (BSP) under the aegis of the European Commission and the Council of Europe, involved 21 official medicines control and industry laboratories from 15 countries. Both methods, an enzyme-linked immunoassay (EIA) and a toxoid inhibition assay (TIA), showed good reproducibility, repeatability and precision. EIA and TIA discriminated between low, medium and high potency samples. Potency estimates correlated well and both values were in close agreement with those obtained by in vivo methods. Moreover, these alternative methods allowed to resolve discrepant results between laboratories that were due to product potency loss and reporting errors. The study demonstrated that EIA and TIA are suitable quality control methods for tetanus immunoglobulin, which can be standardised in a control laboratory using a quality assurance system. Consequently, the Group of Experts on Human Blood and Blood Products of the European Pharmacopoeia revised the monograph on human tetanus immunoglobulins to include both the methods as compendial alternatives to the in vivo mouse challenge assay. 2010 The International Association for Biologicals. Published by Elsevier Ltd. All rights reserved.

  10. 77 FR 14801 - Request for Information (RFI) on Design of a Pilot Operational Study To Assess Alternative Blood...

    Science.gov (United States)

    2012-03-13

    ... permitted to donate under revised selection criteria. A study funded by the Food and Drug Administration... Operational Study To Assess Alternative Blood Donor Deferral Criteria for Men Who Have Had Sex With Other Men... (or studies) on alternative donor deferral criteria that would permit blood and plasma donations...

  11. Substance use and dietary practices among students attending alternative high schools: results from a pilot study

    Directory of Open Access Journals (Sweden)

    Hannan Peter J

    2011-04-01

    Full Text Available Abstract Background Substance use and poor dietary practices are prevalent among adolescents. The purpose of this study was to examine frequency of substance use and associations between cigarette, alcohol and marijuana use and selected dietary practices, such as sugar-sweetened beverages, high-fat foods, fruits and vegetables, and frequency of fast food restaurant use among alternative high school students. Associations between multi-substance use and the same dietary practices were also examined. Methods A convenience sample of adolescents (n = 145; 61% minority, 52% male attending six alternative high schools in the St Paul/Minneapolis metropolitan area completed baseline surveys. Students were participants in the Team COOL (Controlling Overweight and Obesity for Life pilot study, a group randomized obesity prevention pilot trial. Mixed model multivariate analyses procedures were used to assess associations of interest. Results Daily cigarette smoking was reported by 36% of students. Cigarette smoking was positively associated with consumption of regular soda (p = 0.019, high-fat foods (p = 0.037, and fast food restaurant use (p = 0.002. Alcohol (p = 0.005 and marijuana use (p = 0.035 were positively associated with high-fat food intake. With increasing numbers of substances, a positive trend was observed in high-fat food intake (p = 0.0003. There were no significant associations between substance use and fruit and vegetable intake. Conclusions Alternative high school students who use individual substances as well as multiple substances may be at high risk of unhealthful dietary practices. Comprehensive health interventions in alternative high schools have the potential of reducing health-compromising behaviors that are prevalent among this group of students. This study adds to the limited research examining substance use and diet among at-risk youth. Trial registration number ClinicalTrials.gov: NCT01315743

  12. Advanced transportation system studies technical area 3: Alternate propulsion subsystem concepts, volume 2

    Science.gov (United States)

    Levak, Daniel

    1993-01-01

    The Alternate Propulsion Subsystem Concepts contract had five tasks defined for the first year. The tasks were: F-1A Restart Study, J-2S Restart Study, Propulsion Database Development, Space Shuttle Main Engine (SSME) Upper Stage Use, and CER's for Liquid Propellant Rocket Engines. The detailed study results, with the data to support the conclusions from various analyses, are being reported as a series of five separate Final Task Reports. Consequently, this volume only reports the required programmatic information concerning Computer Aided Design Documentation, and New Technology Reports. A detailed Executive Summary, covering all the tasks, is also available as Volume 1.

  13. Complementary and Alternative Medicine in the Pediatrics with Leukemia: A Narrative Review Study

    Directory of Open Access Journals (Sweden)

    Mojtaba Miladinia

    2017-01-01

    Full Text Available BackgroundFor using of complementary and alternative medicine methods (CAM in the leukemia pediatrics than other types of cancer, we have two great challenges; first challenge is their safety and risks and second challenge is study gaps in this field. Regarding to these challenges, this study is a narrative review of some CAM methods in the leukemia pediatrics from the perspective of their safety, risks and study gaps.Materials and MethodsIn this narrative review study searched both international electronic databases including ISI Web of science, PubMed, PsycINFO, CINAHL, ISC, Embase, Scopus, Google Scholar and also, Iranian electronic databases including Magiran, Medlib and SID. Also, searches were performed separately in the specialized journals in the field of leukemia pediatrics and complementary and alternative medicine research.ResultsMusic therapy, gentle yoga movements, gentle massage types are quite safe for leukemia pediatrics. But, use of heavy yoga movements, massages with deep pressure, acupressure and acupuncture can be dangerous for leukemia pediatrics (risks of bleeding and or infection. Also, this study showed that, the number of investigations about the use of CAM in the leukemia pediatrics is very limited; especially in the field of yoga and acupuncture.ConclusionThe results of this study can be a basis both for chose of safe CAM method in these children and a basis for future studies on the basis of identified study gaps in this review study.

  14. Theoretical study of OCCHCN as a potential alternative insulation gas for SF6

    Directory of Open Access Journals (Sweden)

    Zhiguo Chen

    2017-01-01

    Full Text Available Cyanoketene (OCCHCN has been reported as a potential alternative insulation gas for SF6 in Patent US0135817. Stationary point equilibrium geometries on the ground state have been optimized at the B3LYP/6-311+G(d,p level, and the harmonic vibration frequencies are calculated at the same level. The HOMO-LUMO energy gaps (Eg, ionization potentials (IP, and electron affinities (EA of the studied molecules are obtained. The minimum energy path (MEP is obtained by the intrinsic reaction coordinate (IRC theory, and the energetic information is further refined by QCISD(T (single-point method. The results show that OCCHCN can be used as SF6 alternative insulation gas in high voltage equipment according to potential energy surface analysis. As the isomerization and the cleavage reactions potential barriers are lower than the Eg and IP values, resulting in OCCHCN is not easy to be ionized and excited.

  15. Full-scale experimentations on alternative materials in roads: analysis of study practices.

    Science.gov (United States)

    François, D; Jullien, A; Kerzreho, J P; Chateau, L

    2009-03-01

    In France beginning in the 1990s, the topic of road construction using various alternative materials has given rise to several studies aimed at clarifying the technical and environmental feasibility of such an option. Although crucial to understanding and forecasting their behaviour in the field, an analysis of feedback from onsite experiences (back analysis) of roads built with alternative materials has not yet been carried out. The aim of the CAREX project (2003-2005) has been to fill this gap at the national scale. Based on a stress-response approach applied to both the alternative material and the road structure and including the description of external factors, a dedicated standardised framework for field data classification and analysis was adopted. To carry out this analysis, a set of 17 documented field experiments was identified through a specific national survey. It appears that a great heterogeneity exists in data processing procedures among studies. The description of material is acceptable while it is generally poor regarding external factors and structure responses. Structure monitoring is usually brief and mechanical loads too weak, which limits the significance of field testing. For future full-scale experiments, strengthening the realism within the testing conditions would be appropriate.

  16. Value engineering study report on Lower East Fork Poplar Creek Project. Alternative No. 3

    International Nuclear Information System (INIS)

    1995-08-01

    The project under study is Alternative No. 3 as identified in the Feasibility Study dated August 1994. This alternative is identified as Excavation and Disposal of Commercial/DOE, Other, and Residential Remedial Unit Soil. The assumptions used for generating baseline costs are discussed in site associated costs. It is further described as follows: Soils with mercury concentrations greater than 200 ppM in the Commercial/DOE and Other Remedial Units and greater than 180 ppM in the Residential Remedial Unit [41,300m 3 (54,000yd 3 a volume equivalent to approximately 6,750 dump truck loads)] would be excavated and disposed of in an approved, lined landfill at Y-12 with leachate collection and possible pretreatment of the leachate before discharge. Because 0.6 ha (1.5 acres) of wetland would be destroyed, wetlands banking would occur, whereby a 1.8-ha (4.5-acre) wetland would be constructed on DOE-owned land near K-25. Borrow soil would be obtained from the Y-12 West End Borrow Area or from excess soil located at Y-12 landfills to fill the excavation. It is estimated that 7.3 ha (18.2 acres, and area about the size of 17 football fields) of habitat would be adversely affected. This alternative would use BMPs to minimize any adverse affects and to comply substantively with regulatory requirements

  17. Continuum random-phase approximation study of the incoherent μ--e- conversion rate and its spurious 1- admixture

    International Nuclear Information System (INIS)

    Papakonstantinou, P.; Wambach, J.; Kosmas, T.S.; Faessler, A.

    2006-01-01

    The incoherent transition strength of the exotic μ - -e - conversion in the 208 Pb nucleus is investigated by utilizing the continuum random-phase-approximation method, appropriate for the evaluation of the rate that goes to the continuum of the nuclear spectrum. We find that the contribution of resonances lying high in the continuum is not negligible. Special attention is paid to the detailed study of the pronounced 1 - contribution that according to previous calculations, dominates the overall incoherent rate in about all the nuclear targets. The spurious center-of-mass admixture to the partial rate originating from the 1 - excitations is explored, and its elimination is performed by correcting properly the dipole operators. The results found this way show that the greatest portion of the total 1 - contribution to the incoherent rate is spurious

  18. A study of customer commitment through the use of the conversion model in the South African motor vehicle industry

    Directory of Open Access Journals (Sweden)

    Nic Terblanche

    2012-05-01

    Full Text Available Consumer markets have become increasingly competitive. Numerous measures to gauge and predict loyalty and commitment have been developed to assist management in this respect. The marketing literature contains many examples illustrating that longer relationships achieve customer retention, and have been rewarded with a considerable increase in customer net present value. Customer retention is undoubtedly a major contributor to profitability in the long term. Research shows that the most successful measures for achieving customer retention are customer delight, customer satisfaction and customer commitment. This study makes a closer exploration of customer commitment, as measured by the Conversion Model, in the South African motor vehicle industry. The findings highlight the commitment segments of the most popular motor vehicle brands in South Africa, as well the typical marketing strategies for managing the different commitment segments.

  19. 5-fluorocytosine-related bone-marrow depression and conversion to fluorouracil: a pilot study

    NARCIS (Netherlands)

    Vermes, András; Guchelaar, Henk-Jan; van Kuilenburg, Andre B. P.; Dankert, Jacob

    2002-01-01

    The aim of this study is to investigate whether fluorouracil (5-FU) could be responsible for bone-marrow depression occurring in fluorocytosine 5-FC) treated patients. Six 5-FC treated patients were included in this pilot study. Toxicity was monitored by means of thrombocyte and leucocyte counts.

  20. Study of combustion and emission characteristics of fuel derived from waste plastics by various waste to energy (W-t-E) conversion processes

    Science.gov (United States)

    Hazrat, M. A.; Rasul, M. G.; Khan, M. M. K.

    2016-07-01

    Reduction of plastic wastes by means of producing energy can be treated as a good investment in the waste management and recycling sectors. In this article, conversion of plastics into liquid fuel by two thermo-chemical processes, pyrolysis and gasification, are reviewed. The study showed that the catalytic pyrolysis of homogenous waste plastics produces better quality and higher quantity of liquefied fuel than that of non-catalytic pyrolysis process at a lower operating temperature. The syngas produced from gasification process, which occurs at higher temperature than the pyrolysis process, can be converted into diesel by the Fischer-Tropsch (FT) reaction process. Conducive bed material like Olivine in the gasification conversion process can remarkably reduce the production of tar. The waste plastics pyrolysis oil showed brake thermal efficiency (BTE) of about 27.75%, brake specific fuel consumption (BSFC) of 0.292 kg/kWh, unburned hydrocarbon emission (uHC) of 91 ppm and NOx emission of 904 ppm in comparison with the diesel for BTE of 28%, BSFC of 0.276 kg/kWh, uHC of 57 ppm and NOx of 855 ppm. Dissolution of Polystyrene (PS) into biodiesel also showed the potential of producing alternative transport fuel. It has been found from the literature that at higher engine speed, increased EPS (Expanded Polystyrene) quantity based biodiesel blends reduces CO, CO2, NOx and smoke emission. EPS-biodiesel fuel blend increases the brake thermal efficiency by 7.8%, specific fuel consumption (SFC) by 7.2% and reduces brake power (Pb) by 3.2%. More study using PS and EPS with other thermoplastics is needed to produce liquid fuel by dissolving them into biodiesel and to assess their suitability as a transport fuel. Furthermore, investigation to find out most suitable W-t-E process for effective recycling of the waste plastics as fuel for internal combustion engines is necessary to reduce environmental pollution and generate revenue which will be addressed in this article.

  1. Study of the conversion of lignocellulosic (aspen) materials to liquid fuels and chemicals

    Energy Technology Data Exchange (ETDEWEB)

    Pepper, J M; Eager, R L; Mathews, J F

    1979-01-01

    Studies were completed on the use of the small-scale semi-continuous reactor whereby lignocellulosic materials may be converted into a fuel oil. Changes in design and operation were made and further data obtained as a result of studies of the following parameters: pretreatment with sulfuric acid, operating pressure, presence or absence of CO, and nature of feedstock. The major study has centered around the design, construction and testing of a small-scale continuous reactor whose operation was based upon the use of a newly designed screw unit to compress and deliver the wood meal to the reactor site. Chemical studies on oils were obtained from both wood and cellulose. Semi-continuous reactor experiments were run to demonstrate that proto oil could be made continuously under conditions similar to batch runs, and to outline the ranges of the process variable in which satisfactory operation can be maintained for extended periods of time. 7 refs., 4 figs., 5 tabs.

  2. Study of Thermally Responsive Ionic Liquids for Novel Water Desalination and Energy Conversion Applications

    KAUST Repository

    Zhong, Yujiang

    2018-01-01

    The rapidly expanding of the global population in the 21st-century forces people facing two serious problems: water scarcity and energy shortage. Enormous continuous studies focus on providing enough fresh water and energy in a sustainable way

  3. Ocean wave energy conversion

    CERN Document Server

    McCormick, Michael E

    2007-01-01

    This volume will prove of vital interest to those studying the use of renewable resources. Scientists, engineers, and inventors will find it a valuable review of ocean wave mechanics as well as an introduction to wave energy conversion. It presents physical and mathematical descriptions of the nine generic wave energy conversion techniques, along with their uses and performance characteristics.Author Michael E. McCormick is the Corbin A. McNeill Professor of Naval Engineering at the U.S. Naval Academy. In addition to his timely and significant coverage of possible environmental effects associa

  4. Assisting Defense Conversion Technology Transfer Efforts. A Case Study of Ohio’s Miami Valley.

    Science.gov (United States)

    1995-09-01

    Contracting Division, Wright-Patterson AFB OH. Official Letter Correspondence. 24 January 1994. Bryman , Alan. Research Methods and Organization Studies...Washington DC: 22 February 1993. Cooper, Donald R. and C. William Emory. Business Research Methods (Tifth Edition). Chicago: Richard D. Irwin, Inc...data was collected to address the research objective through a case study methodology. First, it describes and justifies the specific method used

  5. Feasibility study for the partial conversion of a hydropower plant into a pumped-storage power plant: a case study of hydroelectric power plant La Barca (Asturias, Spain

    Directory of Open Access Journals (Sweden)

    E. Antuña Yudego

    2017-01-01

    Full Text Available Renewable energy sources have reported an unprecedented increase of global installed renewable power capacity. Against the advantages provided by this renewable power generation technology it should be taken into account an important issue: these intermittent energy sources supply a fluctuating output which is difficult to manage. Pumped-storage hydro power plants reappear in these circumstances as an efficient form of energy storage which allows to use reserves when necessary, enabling power generation output to cover continuously this energy demand. The present paper shows a simplified feasibility study of the partial conversion of hydropower plant La Barca, in Asturias, into a reversible storage through the development of an algorithm to simulate its operation according to electricity market prices. For this purpose, the operation in the deviation management market is considered and the technical modifications required for the conversion are shown. The estimation of costs and incomes present a feasible scenario.

  6. Paradoxical therapy in conversion disorder

    OpenAIRE

    ATAOĞLU, Ahmet

    1998-01-01

    Paradoxical therapy consists of suggesting that the patient intentionally engages in the unwanted behaviour, such as performing complusive ritual or bringing on a conversion attack. In this study paradoxical intention (PI) was used with to half of the patients with conversion disorders, while the other half were treated with diazepam in order to examine the efficiency of the PI versus diazepam in conversion disorder. Patients treated with PI appeared to have a greater improvement r...

  7. Alternating ibuprofen and acetaminophen in the treatment of febrile children: a pilot study [ISRCTN30487061

    Directory of Open Access Journals (Sweden)

    Sabra Ramzi

    2006-03-01

    Full Text Available Abstract Background Alternating ibuprofen and acetaminophen for the treatment of febrile children is a prevalent practice among physicians and parents, despite the lack of evidence on effectiveness or safety. This randomized, double-blind and placebo-controlled clinical trial aims at comparing the antipyretic effectiveness and safety of a single administration of alternating ibuprofen and acetaminophen doses to that of ibuprofen mono-therapy in febrile children. Methods Seventy febrile children were randomly allocated to receive either a single oral dose of 10 mg/kg ibuprofen and 15 mg/kg oral acetaminophen after 4 hours, or a similar dose of ibuprofen and placebo at 4 hours. Rectal temperature was measured at baseline, 4, 5, 6, 7 and 8 hours later. Endpoints included proportions of afebrile children at 6, 7 and 8 hours, maximum decline in temperature, time to recurrence of fever, and change in temperature from baseline at each time point. Intent-to-treat analysis was planned with statistical significance set at P Results A higher proportion of subjects in the intervention group (83.3% became afebrile at 6 hours than in the control group (57.6%; P = 0.018. This difference was accentuated at 7 and 8 hours (P Conclusion A single dose of alternating ibuprofen and acetaminophen appears to be a superior antipyretic regimen than ibuprofen mono-therapy. Further studies are needed to confirm these findings.

  8. Coping behavior in multiple sclerosis-complementary and alternative medicine: A cross-sectional study.

    Science.gov (United States)

    Rommer, Paulus S; König, Nicolaus; Sühnel, Annett; Zettl, Uwe K

    2018-04-10

    Treatment options for multiple sclerosis (MS) have enlarged tremendously over the last years. Nonetheless, lots of patients look for alternative treatment options. The use of complementary and alternative medicine (CAM) is widespread in MS, however, its scientific investigation is limited so far. The aim of the study is to analyse clinical and demographical differences of MS patients in dependency of their CAM utilization as coping strategy. A total of 254 patients with a clinically definite MS were examined in a semistructured interview. Additional standardized questionnaires were used to measure different aspects of coping with illness. All patients underwent neurological examination. About 206 of all enrolled patients are CAM users (81.1%). They have a longer disease duration (8.3 years vs 7.3 years, P = 0.028) and show higher disability (median EDSS 4.0 vs 2.0, P alternative or complementary methods. CAM utilization may mirror unmet needs in the treatment of MS. © 2018 The Authors. CNS Neuroscience & Therapeutics Published by John Wiley & Sons Ltd.

  9. An Experimental Study of Surfactant Alternating CO2 Injection for Enhanced Oil Recovery of Carbonated Reservoir

    Directory of Open Access Journals (Sweden)

    Asghar Gandomkar

    2016-10-01

    Full Text Available Core flooding experiments were conducted with the objective of evaluating near miscible surfactant alternating CO2 injection and the effect of surfactant concentrations on gas-oil and water displacements in porous media. The core samples were provided from a low permeability mixed wet oil reservoir at 156 °F and 1900 psia. In addition, very few studies of surfactant adsorption on carbonate minerals have been conducted. Hence, the surfactant adsorption on carbonate rock was determined by core flooding and crushed tests. It was found that for the crushed rock, the required equilibrium time is approximately five hours, while it is more than four days for the flow-through tests. Hysteresis effects demonstrated that the irreducible water saturations were 5 to 10% higher than the initial connate water saturation after drainage cycles during 5000 ppm surfactant solution. Furthermore, near-miscible surfactant alternating CO2 injection process led to a 4-17% increase in the recovery factor in comparison to water alternating gas process.

  10. Theoretical and NMR conformational studies of β-proline oligopeptides with alternating chirality of pyrrolidine units

    Science.gov (United States)

    Mantsyzov, Alexey B.; Savelyev, Oleg Y.; Ivantcova, Polina M.; Bräse, Stefan; Kudryavtsev, Konstantin V.; Polshakov, Vladimir I.

    2018-03-01

    Synthetic β-peptides are potential functional mimetics of native α-proteins. A recently developed, novel, synthetic approach provides an effective route to the broad group of β-proline oligomers with alternating patterns of stereogenic centers. Conformation of the pyrrolidine ring, Z/E isomerism of β-peptide bonds, and hindered rotation of the neighboring monomers determine the spatial structure of this group of β-proline oligopeptides. Preferences in structural organization and corresponding thermodynamic properties are determined by NMR spectroscopy, restrained molecular dynamics and quantum mechanics. The studied β-proline oligopeptides exist in dimethyl sulfoxide solution in a limited number of conformers, with compatible energy of formation and different spatial organization. In the β-proline tetrapeptide with alternating chirality of composing pyrrolidine units, one of three peptide bonds may exist in an E configuration. For the alternating β-proline pentapeptide, the presence of an E configuration for at least of one β-peptide bond is mandatory. In this case, three peptide bonds synchronously change their configurations. Larger polypeptides may only exist in the presence of several E configurations of β-peptide bonds forming a wave-like extended structure.

  11. Theoretical and NMR Conformational Studies of β-Proline Oligopeptides With Alternating Chirality of Pyrrolidine Units

    Directory of Open Access Journals (Sweden)

    Alexey B. Mantsyzov

    2018-03-01

    Full Text Available Synthetic β-peptides are potential functional mimetics of native α-proteins. A recently developed, novel, synthetic approach provides an effective route to the broad group of β-proline oligomers with alternating patterns of stereogenic centers. Conformation of the pyrrolidine ring, Z/E isomerism of β-peptide bonds, and hindered rotation of the neighboring monomers determine the spatial structure of this group of β-proline oligopeptides. Preferences in their structural organization and corresponding thermodynamic properties are determined by NMR spectroscopy, restrained molecular dynamics and quantum mechanics. The studied β-proline oligopeptides exist in dimethyl sulfoxide solution in a limited number of conformers, with compatible energy of formation and different spatial organization. In the β-proline tetrapeptide with alternating chirality of composing pyrrolidine units, one of three peptide bonds may exist in an E configuration. For the alternating β-proline pentapeptide, the presence of an E configuration for at least of one β-peptide bond is mandatory. In this case, three peptide bonds synchronously change their configurations. Larger polypeptides may only exist in the presence of several E configurations of β-peptide bonds forming a wave-like extended structure.

  12. Repair work in the context of English language mediated computer interface use: A conversation analytic study

    DEFF Research Database (Denmark)

    Raudaskoski, Pirkko

    1992-01-01

    The main aim in this study is to develop an understanding of how repair work is managed in the intertwining of activities and actions with talk and language. By doing this, the richness of the concept of repair in interactional studies is shown. The core work concentrates on exploring repair work...... the English language as a resource. The computer interface use context was chosen to show how narrowly traditional research has seen repair work.......The main aim in this study is to develop an understanding of how repair work is managed in the intertwining of activities and actions with talk and language. By doing this, the richness of the concept of repair in interactional studies is shown. The core work concentrates on exploring repair work...... in the context of participants solving interactional troubles in their activities. Many types of resources are potentially available in any situation, from the physical features of tools to the cultural context. In this study the interest lies especially in the more complicated artifacts which also offer...

  13. Infrared studies of ortho-para conversion at Cl-atom and H-atom impurity centers in cryogenic solid hydrogen

    International Nuclear Information System (INIS)

    Raston, P.L.; Kettwich, S.C.; Anderson, D.T.

    2010-01-01

    We report infrared spectroscopic studies of H 2 ortho-para (o/p) conversion in solid hydrogen doped with Cl-atoms at 2 K while the Cl + H 2 (υ = 1) → HCl + H infrared-induced chemical reaction is occurring. The Cl-atom doped hydrogen crystals are synthesized using 355 nm in situ photodissociation of Cl 2 precursor molecules. For hydrogen solids with high ortho-H 2 fractional concentrations (X o = 0.55), the o/p conversion kinetics is dominated by Cl-atom catalyzed conversion with a catalyzed conversion rate constant K cc = 1.16(11) min -1 and the process is rate-limited by ortho-H 2 quantum diffusion. For hydrogen crystals with low ortho-H2 concentrations (X o = 0.03), single-exponential decay of the ortho-H 2 concentration with time is observed which is attributed to H-atom catalyzed o/p conversion by the H-atoms produced during the infrared-induced Cl + H 2 reaction. The measured H-atom catalyzed o/p conversion kinetics indicates the H-atoms are mobile under these conditions in agreement with previous ESR measurements.

  14. An Open Conversation on Using Eye-Gaze Methods in Studies of Neurodevelopmental Disorders

    Science.gov (United States)

    Venker, Courtney E.; Kover, Sara T.

    2015-01-01

    Purpose: Eye-gaze methods have the potential to advance the study of neurodevelopmental disorders. Despite their increasing use, challenges arise in using these methods with individuals with neurodevelopmental disorders and in reporting sufficient methodological detail such that the resulting research is replicable and interpretable. Method: This…

  15. Induced Pluripotent Stem Cell Technology and Direct Conversion : New Possibilities to Study and Treat Parkinson's Disease

    NARCIS (Netherlands)

    Roessler, Reinhard; Boddeke, Erik; Copray, Sjef

    Recent developments in in vitro disease modeling and regenerative medicine have placed induced pluripotent stem cells (iPSCs) in the center of attention as a unique source to study Parkinson's disease. After only 5 years of intensive research, human iPSCs can be generated without viral integration

  16. A Case Study of Middle Grades Leadership in a Conversion Charter School

    Science.gov (United States)

    Bickmore, Dana L.; Dowell, Margaret-Mary Sulentic

    2015-01-01

    This 3-year case study examined middle grades principal leadership in a takeover charter school. The researcher analyzed principal and teacher interviews, field notes, and documents in relationship to a middle grades model of principal leadership. Results suggest the principals' limited experience, organizational factors unique to takeover charter…

  17. Individualized Education Program Team Decisions: A Preliminary Study of Conversations, Negotiations, and Power

    Science.gov (United States)

    Ruppar, Andrea L.; Gaffney, Janet S.

    2011-01-01

    Given the centrality of the Individualized Education Program (IEP) to services for students with disabilities, the decision-making process during the IEP meeting deserves attention in research and implementation. In this case study, IEP team decision-making is examined as a socially situated practice. Transcripts of an initial evaluation and IEP…

  18. Intracellular PHB conversion in a type II methanotroph studied by 13 C NMR

    NARCIS (Netherlands)

    Vecherskaya, M.; Dijkema, C.; Stams, A.J.M.

    2001-01-01

    Poly-g-hydroxybutyrate (PHB) formation under aerobic conditions via incorporation of [13C-2]acetate as a cosubstrate and its intracellular degradation under anaerobic conditions in a Type II methanotroph was studied by 13C NMR. During PHB synthesis in the presence of labelled acetate, low levels of

  19. Creating Critical Conversations: Investigating the Utility of Socratic Dialogues in Elementary Social Studies Methods

    Science.gov (United States)

    Buchanan, Lisa Brown

    2012-01-01

    This article explores the utility of Socratic dialogues in the elementary social studies methods course. Findings include preservice teachers' behaviors during dialogues, perceived strengths and challenges of using Socratic dialogues in teacher education, and the impact on student learning. Challenges and apprehensions encountered by the teacher…

  20. Corrosion study of heat exchanger tubes in pressurized water cooled nuclear reactors by conversion electron Moessbauer spectroscopy

    International Nuclear Information System (INIS)

    Homonnay, Z.; Kuzmann, E.; Varga, K.; Nemeth, Z.; Szabo, A.; Rado, K.; Schunk, J.; Tilky, P.; Patek, G.

    2005-01-01

    Nuclear energy production tends to return into the focus of interest because of the constantly increasing energy need of the world and the green house effect problems of the strongest competitor oil or gas based power plants. In addition to the construction of new nuclear power plants, lifetime extension of the existing ones is the most cost effective investment in the energy business. However, feasibility and safety issues become very important at this point, and corrosion of the construction materials should be carefully investigated before decision on a potential lifetime extension of a reactor. 57 Fe-Conversion Electron Moessbauer Spectroscopy (CEMS) is a sensitive tool to analyze the phase composition of corrosion products on the surface of stainless steel. The upper ∼300 nm can be investigated due to the penetration range of conversion electrons. The corrosion state of heat exchanger tubes from the four reactor units of the Paks Nuclear Power Plant, Hungary, were analyzed by several methods including CEMS. The primary circuit side of the tubes was studied on selected samples cut out from the heat exchangers during regular maintenance. Cr- and Ni-substituted magnetite, sometimes hematite, amorphous Fe-oxides/oxyhydroxides as well as the signal of bulk austenitic steel of the tubes were detected. The level of Cr- and Ni-substitution in the magnetite phase could be estimated from the Moessbauer spectra. Correlation between earlier decontamination cycles and the corrosion state of the heat exchangers was sought. In combination with other methods, a hybrid structure of the surface oxide layer of several microns was established. It is suggested that previous AP-CITROX decontamination cycles can be responsible for this structure which makes the oxide layer mobile. This mobility may be responsible for unwanted corrosion product transport into the reactor vessel by the primary coolant.

  1. Quantum mechanical study of the proton exchange in the ortho-para H2 conversion reaction at low temperature.

    Science.gov (United States)

    Honvault, P; Jorfi, M; González-Lezana, T; Faure, A; Pagani, L

    2011-11-14

    Ortho-para H(2) conversion reactions mediated by the exchange of a H(+) proton have been investigated at very low energy for the first time by means of a time independent quantum mechanical (TIQM) approach. State-to-state probabilities and cross sections for H(+) + H(2) (v = 0, j = 0,1) processes have been calculated for a collision energy, E(c), ranging between 10(-6) eV and 0.1 eV. Differential cross sections (DCSs) for H(+) + H(2) (v = 0, j = 1) → H(+) + H(2) (v' = 0, j' = 0) for very low energies only start to develop a proper global minimum around the sideways scattering direction (θ≈ 90°) at E(c) = 10(-3) eV. Rate coefficients, a crucial information required for astrophysical models, are provided between 10 K and 100 K. The relaxation ortho-para process j = 1 → j' = 0 is found to be more efficient than the j = 0 → j' = 1 conversion at low temperatures, in line with the extremely small ratio between the ortho and para species of molecular hydrogen predicted at the temperature of interstellar cold molecular clouds. The results obtained by means of a statistical quantum mechanical (SQM) model, which has previously proved to provide an adequate description of the dynamics of the title reactions at a higher collision energy regime, have been compared with the TIQM results. A reasonable good agreement has been found with the only exception of the DCSs for the H(+) + H(2) (v = 0, j = 1) → H(+) + H(2) (v' = 0, j' = 0) process at very low energy. SQM cross sections are also slightly below the quantum results. Estimates for the rate coefficients, in good accord with the TIQM values, are a clear improvement with respect to pioneering statistical studies on the reaction.

  2. Conversation and research

    NARCIS (Netherlands)

    Schuurman, Jan Gerrit; Veermans, K.H.

    2001-01-01

    Gordon Pask’s conversation theory was created in the 1970s. The theory encompasses a high-level framework for studying interactions between actors in artificial situations where people co-operate, have conflicts, follow rules, negotiate outcomes, invent new rules together, etc. Sadly, the theory is

  3. A neutronic feasibility study for LEU conversion of the Brookhaven Medical Research Reactor (BMRR).

    Energy Technology Data Exchange (ETDEWEB)

    Hanan, N. A.

    1998-01-14

    A neutronic feasibility study for converting the Brookhaven Medical Research Reactor from HEU to LEU fuel was performed at Argonne National Laboratory in cooperation with Brookhaven National Laboratory. Two possible LEU cores were identified that would provide nearly the same neutron flux and spectrum as the present HEU core at irradiation facilities that are used for Boron Neutron Capture Therapy and for animal research. One core has 17 and the other has 18 LEU MTR-type fuel assemblies with uranium densities of 2.5g U/cm{sup 3} or less in the fuel meat. This LEU fuel is fully-qualified for routine use. Thermal hydraulics and safety analyses need to be performed to complete the feasibility study.

  4. A neutronics feasibility study for the LEU conversion of Poland's Maria research reactor

    International Nuclear Information System (INIS)

    Bretscher, M. M.

    1998-01-01

    The MARIA reactor is a high-flux multipurpose research reactor which is water-cooled and moderated with both beryllium and water. Standard HEU (80% 235 U)fuel assemblies consist of six concentric fuel tubes of a U-Al alloy clad in aluminum. Although the inventory of HEU (80%) fuel is nearly exhausted, a supply of highly-loaded 36%-enriched fuel assemblies is available at the reactor site. Neutronic equilibrium studies have been made to determine the relative performance of fuels with enrichments of 80%, 36% and 19.7%. These studies indicate that LEU (19.7%) densities of about 2.5 gU/cm 3 and 3.8 gU/cm 3 are required to match the performance of the MARIA reactor with 80%-enriched and with 36%-enriched fuels, respectively

  5. A study of the stressor, family environment and family burden in dissociative (conversion disorder patients

    Directory of Open Access Journals (Sweden)

    Kamal K Verma

    2017-01-01

    Full Text Available Background: Dissociative disorder is a stress-related disorder usually present in adolescent and younger age group. It is also accompanied with significant impairment in activity of daily living and family relationship. Family environment plays important role in initiation and maintenance of symptoms and this put significant burden on family. Aim and Objective: To study presence of stressor, family environment, and assessment of family burden in dissociative disorder patients. Material and Method: This was a cross-sectional observational study in which 100 dissociatives disorder patients were included after fulfilling inclusion criteria from both inpatients and outpatient department of psychiatry. Results: In our study major part of the sample were women 60 (60%, among them most of were housewife and educated up to primary school. According to a stressor, 63 (63% patients had family stress/problem and out of them, 35 (58.4 were women. Seventy-four (74% patients had dissociative convulsion and out of them, 45 (75% were women. The dissociative disorder patients cause a considerable degree of burden over other family members in both men and women. There is a significant difference found in the family environment in term of personal growth dimension, relationship dimension in both men and women. Conclusion: Present study concludes that dissociative disorder patients cause a considerable degree of burden over other family members in term of leisure, physical, mental, financial, and routines family interrelationship domains. The family environment in term of personal growth dimension, relationship dimension has a casual effect on symptoms of dissociative disorder patients.

  6. Transitivity in Telephone Conversation in a Bribery Case in Indonesia : a Forensic Linguistic Study

    OpenAIRE

    Waskita, Dana

    2014-01-01

    Penelitian ini adalah sebuah kajian linguistik atas percakapan telepon dalam bahasa Indonesia pada kasus korupsi yang terjadi baru-baru ini, khususnya sebuah kasus penyuapan. Pendekatan linguistik pragmatis dan sistemik fungsional digunakan sebagai metode untuk mengungkapkan fakta-fakta yang ditemukan pada kasus penyuapan sebagai suatu jenis kasus hukum dalam studi Linguistik Forensik. Percakapan telepon dari dua jenis penyuapan dikumpulkan sebagai data penelitian ini. Data dianalisis secara ...

  7. Experimental study of the effects of alternating fields on HTS coils according to the winding insulation conditions

    International Nuclear Information System (INIS)

    Hwang, Y J; Lee, T S; Lee, W S; Ko, T K; Ahn, M C

    2013-01-01

    This paper examines the effects of alternating fields on high-temperature superconducting (HTS) coils according to the winding insulation condition. Alternating fields can occur in synchronous machines (armature reaction, faults) and other devices. In superconducting synchronous machines, alternating fields affect the operational characteristics of the machine and the superconducting field coil. Therefore, a method of reducing the effects of alternating fields is necessary in superconducting synchronous design. In this study, the effects of alternating fields on the HTS field coil according to the winding insulation condition were experimentally evaluated. The experimental results show that HTS coils made using the no-insulation technique can be a solution for reducing the effects of the alternating field. These results are expected to suggest useful data for applications of HTS field coils in superconducting synchronous machines. (paper)

  8. Contribution to the study of the conversion PWR type reactors to the thorium cycle

    International Nuclear Information System (INIS)

    Martins Filho, J.R.

    1980-01-01

    The use of the thorium cycle in PWR reactors is discussed. The fuel has been calculated in the equilibrium condition for a economic comparison with the uranium cycle (in the same condition). First of all, a code named EQUILIBRIO has been developed for the fuel equilibrium calculation. The results gotten by this code, were introduced in the LEOPARD code for the fuel depletion calculation (in the equilibrium cycle). Same important physics details of fuel depletion are studied, for instance: the neutron balance, power sharing, fuel burnup, etc. The calculations have been done taking as reference the Angra-1 PWR reactor. (Author) [pt

  9. FT-IR spectroscopic analysis for studying Clostridium cell response to conversion of enzymatically hydrolyzed hay

    Science.gov (United States)

    Grube, Mara; Gavare, Marita; Nescerecka, Alina; Tihomirova, Kristina; Mezule, Linda; Juhna, Talis

    2013-07-01

    Grass hay is one of assailable cellulose containing non-food agricultural wastes that can be used as a carbohydrate source by microorganisms producing biofuels. In this study three Clostridium strains Clostridium acetobutylicum, Clostridium beijerinckii and Clostridium tetanomorphum, capable of producing acetone, butanol and ethanol (ABE) were adapted to convert enzymatically hydrolyzed hay used as a growth media additive. The results of growth curves, substrate degradation kinetics and FT-IR analyses of bacterial biomass macromolecular composition showed diverse strain-specific cell response to the growth medium composition.

  10. Fumarate to Malate Conversion in Infarcted Porcine Heart – a Pilot Study

    DEFF Research Database (Denmark)

    Søvsø Szocska Hansen, Esben; Tougaard, Rasmus Stilling; Nielsen, Per Mose

    2017-01-01

    Hyperpolarized MR may be a key tool for investigation cardiac metabolism and cardiac treatment response. [1,4- 13C2]Fumarate is an emerging and interesting candidate for measuring and visualizing cardiac injury after ischemia. In this study we showed an initial step for imaging cardiac cell death...... in a large animal model with [1,4- 13C2]malate. The [1,4- 13C2]malate signal correlated well with increased 13C-lactate signal and 13C-alanine absence. Overall, this shows increased metabolism in the infarcted area and ongoing necrosis....

  11. Allocentric spatial memory testing predicts conversion from mild cognitive impairment to dementia: an initial proof-of-concept study

    Directory of Open Access Journals (Sweden)

    Ruth A Wood

    2016-12-01

    Full Text Available The hippocampus is one of the first regions to exhibit neurodegeneration in Alzheimer’s disease (AD and knowledge of its role in allocentric spatial memory may therefore aid early diagnosis of AD. The 4 Mountains Test (4MT is a short and easily administered test of spatial memory based on the cognitive map theory of hippocampal function as derived from rodent single cell and behavioral studies. The 4MT has been shown in previous cross-sectional studies to be sensitive and specific for mild cognitive impairment due to AD. This report describes the initial results of a longitudinal study testing the hypothesis that allocentric spatial memory is predictive of conversion from mild cognitive impairment to dementia.Fifteen patients with mild cognitive impairment underwent baseline testing on the 4MT in addition to CSF amyloid/tau biomarker studies, volumetric MRI and neuropsychological assessment including the Rey Auditory Verbal Learning Test (RAVLT and Trail Making Test B (TMT-B. At 24 months, 9/15 patients had converted to AD dementia. The 4MT predicted conversion to AD with 93% accuracy (Cohen’s d = 2.52. The predictive accuracies of the comparator measures were as follows: CSF tau/β-amyloid1-42 ratio 92% (d = 1.81, RAVLT 64% (d = 0.41, TMT-B 78% (d = 1.56, and hippocampal volume 77% (d = 0.65. CSF tau levels were strongly negative correlated with 4MT scores (r = -0.71. This proof-of-concept study provides initial support for the hypothesis that allocentric spatial memory testing is a predictive cognitive marker of hippocampal neurodegeneration in pre-dementia AD. The 4MT is a brief, noninvasive, straightforward spatial memory test and is therefore ideally suited for use in routine clinical diagnostic practice. This is of particular importance given the current unmet need for simple accurate diagnostic tests for early AD and the ongoing development of potential disease-modifying therapeutic agents which may be more efficacious when given

  12. Allocentric Spatial Memory Testing Predicts Conversion from Mild Cognitive Impairment to Dementia: An Initial Proof-of-Concept Study.

    Science.gov (United States)

    Wood, Ruth A; Moodley, Kuven K; Lever, Colin; Minati, Ludovico; Chan, Dennis

    2016-01-01

    The hippocampus is one of the first regions to exhibit neurodegeneration in Alzheimer's disease (AD), and knowledge of its role in allocentric spatial memory may therefore aid early diagnosis of AD. The 4 Mountains Test (4MT) is a short and easily administered test of spatial memory based on the cognitive map theory of hippocampal function as derived from rodent single cell and behavioral studies. The 4MT has been shown in previous cross-sectional studies to be sensitive and specific for mild cognitive impairment (MCI) due to AD. This report describes the initial results of a longitudinal study testing the hypothesis that allocentric spatial memory is predictive of conversion from MCI to dementia. Fifteen patients with MCI underwent baseline testing on the 4MT in addition to CSF amyloid/tau biomarker studies, volumetric MRI and neuropsychological assessment including the Rey Auditory Verbal Learning Test (RAVLT) and Trail Making Test "B" (TMT-B). At 24 months, 9/15 patients had converted to AD dementia. The 4MT predicted conversion to AD with 93% accuracy (Cohen's d  = 2.52). The predictive accuracies of the comparator measures were as follows: CSF tau/β-amyloid 1-42 ratio 92% ( d  = 1.81), RAVLT 64% ( d  = 0.41), TMT-B 78% ( d  = 1.56), and hippocampal volume 77% ( d  = 0.65). CSF tau levels were strongly negatively correlated with 4MT scores ( r  = -0.71). This proof-of-concept study provides initial support for the hypothesis that allocentric spatial memory testing is a predictive cognitive marker of hippocampal neurodegeneration in pre-dementia AD. The 4MT is a brief, non-invasive, straightforward spatial memory test and is therefore ideally suited for use in routine clinical diagnostic practice. This is of particular importance given the current unmet need for simple accurate diagnostic tests for early AD and the ongoing development of potential disease-modifying therapeutic agents, which may be more efficacious when given earlier in

  13. Quality of Parent-Adolescent Conversations About Sex and Adolescent Sexual Behavior: An Observational Study.

    Science.gov (United States)

    Rogers, Adam A; Ha, Thao; Stormshak, Elizabeth A; Dishion, Thomas J

    2015-08-01

    Studies suggest that the quality of parent-adolescent communication about sex uniquely predicts adolescent sexual behavior. Previous studies have relied predominantly on self-report data. Observational methods, which are not susceptible to self-report biases, may be useful in examining the associations between the quality of parent-adolescent communication about sex and adolescent sexual behavior more objectively. With a sample of adolescents (N = 55, 58% male, 44% white, Mage = 15.8) and their parents, we used hierarchical logistic regression analyses to examine the associations between the observed quality of parent-adolescent communication about dating and sex and the likelihood of adolescents' sexual intercourse. The quality of parent-adolescent communication about dating and sex predicted sexual behavior. Specifically, lecturing was associated with a higher likelihood of adolescents having had sexual intercourse. The quality of parent-adolescent communication about sex is a unique correlate of adolescent sexual behavior and warrants further investigation. Thus, it serves as a potential target of preventive interventions that aim to foster adolescent sexual health behaviors. Copyright © 2015 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

  14. A neutronic feasibility study for LEU conversion of the WWR-M reactor at Gatchina

    International Nuclear Information System (INIS)

    Petrov, Yu. V.; Erykalov, A.N.; Onegin, M.S.

    2000-01-01

    In this report we present the results of computations of the full scale reactor core with HEU (90%), MEU (36%) and LEU (19.75%) fuel. The reactor computer model for the MCU RFFI Monte Carlo code includes all peculiarities of the core. Calculations show that a uranium density of 3.3gU/cm 3 of MEU (36%) fuel and 8/25gU/cm 3 of LEU (19.75%) in WWR-M5 fuel assembly (FA) geometry is required to match the fuel cycle length of the HEU (90%) case with the same end of cycle (EOEC) excess reactivity. For the equilibrium fuel cycle the fuel burnup and poisoning, the fast and thermal neutron fluxes, the reactivity worth of control rods were calculated for the reference case with HEU (90%) FA and for the MEU and LEU FA. The relative accuracy of this neutronic feasibility study of fuel enrichment reduction of the WWR-M reactor in Gatchina is sufficient to start the fabrication feasibility study of MEU (36%) WWR-M5 fuel assemblies. At the present stage of technology it seems hardly possible to manufacture LEU (19.75%) fuel elements in WWR-M5 geometry due to too high uranium density. Only a future R and D can solve the problem. (author)

  15. Avoidant conversations about death by clinicians cause delays in reporting of neutropenic sepsis: Grounded theory study.

    Science.gov (United States)

    Oakley, Catherine; Taylor, Cath; Ream, Emma; Metcalfe, Alison

    2017-10-01

    Evidence suggests that patients delay reporting symptoms of neutropenic sepsis (NS) despite the risk to their life. This study aimed to elicit factors that contribute to delayed patient reporting of NS symptoms. A constructivist grounded theory study used observations of chemotherapy consultations (13 h) and 31 in-depth interviews to explore beliefs, experiences, and behaviors related to NS. Participants included women with breast cancer, their carers (partners, family, or friends), and clinicians. An explanation for patient delays was developed through theoretical sampling of participants to explore emerging areas of interest and through constant comparison of data and their coding. This entailed iterative and concurrent data collection and analysis. Data were collected until saturation. All patients who developed NS-type symptoms delayed presenting to hospital (2.5 h-8 days), sometimes repeatedly. Moderators of delay included metastatic disease, bereavement, fatalism, religious beliefs, and quality of relationships with clinicians. There was an interplay of behaviors between clinicians, patients, and carers where they subconsciously conspired to underplay the seriousness and possibility of NS occurring. Findings have implications for health risk communication and development of holistic service models. Copyright © 2016 John Wiley & Sons, Ltd.

  16. Conversion of Oleum papaveris seminis oil into methyl esters via esterification process optimization and kinetic study

    Energy Technology Data Exchange (ETDEWEB)

    Syam, A.M.; Rashid, U.; Yunus, R.; Hamid, H.A.; Al-Resayes, S.I.; Nehdi, I.A.; Al-Muhtaseb, A.H.

    2016-07-01

    This paper presents an acid pre-treatment process and a kinetic study for the esterification reaction of Oleum papaveris seminis oil with methanol in the presence of amberlite 120 as a solid catalyst to convert the oil into methyl esters. Response surface methodology (RSM) was applied to optimize the reaction parameters, i.e. reaction time, percentage of the catalyst and volume ratio of methanol to oil. The results revealed that 0.87% w/w of catalyst concentration and 44.70% v/v of methanol to oil ratio provided final free fatty acid (FFA) contents of 0.60% w/w at 102.40 min of reaction time. It proved that the contribution of Amberlite 120 in the esterification of FFA was highly significant. The kinetics of the esterification in Oleum papaveris seminis oil with methanol in the presence of the amberlite 120 catalyst were also investigated to establish the reaction rate constant (k), reaction order, and activation energy. The study was performed under the optimized parameters at three reaction temperatures (50, 55, and 60 ºC). The value of k was in the range of 0.013 to 0.027 min-1. The first-order kinetics’ model was suitable for this irreversible FFA esterification with the activation energy of about 60.9 KJ·mol-1. (Author)

  17. Costs for Alternatives to District Heating. A study of real costs on local heating markets; Alternativkostnad till fjaerrvaerme. En studie av verkliga kostnader paa lokala vaermemarknader

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, Annelie; Lehtmets, Marti; Andersson, Sofie

    2008-07-01

    Heating comprise the major part of the cost of supporting a building with necessities like electricity, heat, refuse collection and water and sewage. As these costs increase, it is becoming more interesting to find other solutions in order to reduce them. One alternative is to convert to another heating system. Several price analyses comparing different heating systems have been performed. Avgiftsgruppen publishes one report on a yearly basis, where the costs to support a building with necessities and how they vary between communities are listed. The latest report states that it is less expensive in 75 % of the communities in Sweden to convert from district heating to a pellets boiler or a ground-source pump. However, other studies have established that the heat market is a local market with local conditions. Therefore you need to compare alternative heating costs that are specific to the area instead of estimated average costs at a national level. The purpose of this survey is to study a local heat market in order to verify the real cost of the alternative heating systems to district heating and if these costs vary between different communities. The hypothesis is that it is not possible to generalize the heating cost on a national level. Instead, a local market should be studied to make an accurate cost comparison between heating options. Three communities are studied in order to find real and verified investment costs in pellet boilers and heat pumps. The investments that are of primary interest are those performed in buildings similar to the multi-dwelling house used in earlier price analyses. Furthermore, the building should be located within the distribution network of district heating in order to illustrate the competition between the heating alternatives. The result of the study illustrates the difficulties to find real and verified costs of completed investments in alternative heating systems in buildings that is of primary interest for this study. Contacts

  18. Electron autoradiographic study of intracellular conversion of fatty acids into glycogen in rats with alloxan diabetes

    International Nuclear Information System (INIS)

    Lebkova, N.P.; Bobkov, Y.I.; Gorbonova, V.D.; Kolesova, O.E.

    1985-01-01

    An electron-autoradiographic study was undertaken of the intracellular distribution of hydrogen of fatty acids in alloxan diabetes. Alloxan diabetes was induced in rats; between 2 weeks and 2 months after development of the disease 0.1 ml of tritium-oleic or tritium-arachidonic acid was injected into the caudel vein of the rats. After decapitation, myocardial tissue from the subendocardial zone of the left ventricle, liver tissue, and glycogen isolated from the liver by a biochemical method, were taken for electron-autoradiographic investigation. Analysis of the data showed that a radioactive isotope, injected into the blood stream of the animals in the form of oleic or arachidonic acids, is incorporated into various structures of hepatocytes and cardiomyocytes. Direct proof is obtained to show that glycogen in hepatocytes and cardiomyoctyes of diabetic rats may be formed from fatty acids

  19. Green conversion of graphene oxide to graphene nanosheets and its biosafety study.

    Directory of Open Access Journals (Sweden)

    Adhiraj Dasgupta

    Full Text Available Chemical reduction of graphene oxide (GO to graphene employs the use of toxic and environmentally harmful reducing agents, hindering mass production of graphene which is of tremendous technological importance. In this study we report a green approach to the synthesis of graphene, bio-reduced by crude polysaccharide. The polysaccharide reduces exfoliated GO to graphene at room temperature in an aqueous medium. Transmission electron microscopy image provides clear evidence for the formation of few layer graphene. Characterization of the resulting polysaccharide reduced GO by Raman spectroscopy, Fourier transform infrared spectroscopy and Energy dispersive X-ray analysis confirms reduction of GO to graphene. We also investigated the degree of biosafety of the reduced GO and found it to be safe under 100 μg/ml.

  20. The fission-track analysis: An alternative technique for provenance studies of prehistoric obsidian artefacts

    CERN Document Server

    Bellot-Gurlet, L; Dorighel, O; Oddone, M; Poupeau, G; Yegingil, Z

    1999-01-01

    Comparison of fission-track parameters - age and track densities - is an alternative tool for correlating obsidian artefacts with their potential natural sources. This method was applied by different fission-track groups in various regions and results were compared with those obtained using the more popular provenance identification techniques based on chemical composition studies. Hundreds of analyses prove that fission-track dating is a complementary technique which turns out to be very useful, specially when the chemical composition does not fully discriminate different sources. Archaeologically significant results were obtained applying the fission-track analysis in various regions of earth.

  1. Use of alternative sources of energy: design study of photovoltaic based parking area lighting system

    International Nuclear Information System (INIS)

    Perraki, V.; Loucas, G.

    2000-01-01

    This study proposes the lighting of the parking area and the surrounding streets of the north west part of the University Campus of Patras, using an alternative source of energy, the photovoltaic energy. The sizing of the proposed system results to a reliable, autonomous system which covers the total of the energy needs without any maintenance. Although the energy produced is more expensive compared to the grid electricity nowadays, such solutions seem necessary and well promising for the future as the fuel reserves are limited. (authors)

  2. The fission-track analysis: An alternative technique for provenance studies of prehistoric obsidian artefacts

    International Nuclear Information System (INIS)

    Bellot-Gurlet, L.; Bigazzi, G.; Dorighel, O.; Oddone, M.; Poupeau, G.; Yegingil, Z.

    1999-01-01

    Comparison of fission-track parameters - age and track densities - is an alternative tool for correlating obsidian artefacts with their potential natural sources. This method was applied by different fission-track groups in various regions and results were compared with those obtained using the more popular provenance identification techniques based on chemical composition studies. Hundreds of analyses prove that fission-track dating is a complementary technique which turns out to be very useful, specially when the chemical composition does not fully discriminate different sources. Archaeologically significant results were obtained applying the fission-track analysis in various regions of earth

  3. Treatability studies of alternative wastewaters for Metal Finishing Effluent Treatment Facility

    International Nuclear Information System (INIS)

    Wittry, D.M.; Martin, H.L.

    1994-01-01

    The 300-M Area Liquid Effluent Treatment Facility (LETF) of the Savannah River Site (SRS) is an end-of-pipe industrial wastewater treatment facility that uses precipitation and filtration, which is the EPA Best Available Technology economically achievable for a Metal Finishing and Aluminum Form Industries. Upon the completion of stored waste treatment, the LETF will be shut down, because production of nuclear materials for reactors stopped at the end of the Cold War. The economic use of the LETF for the treatment of alternative wastewater streams is being evaluated through laboratory bench-scale treatability studies

  4. Alternative dispute resolution programs in health care: a study of organizational utilization.

    Science.gov (United States)

    Rotarius, T M; Liberman, A; Osterman, K C; Putnam, P

    1999-03-01

    The hyperturbulence in today's health care environment acts as a primer that escalates the frequency and severity of business conflicts. Several alternative dispute resolution (ADR) programs are described, with ADR suggested as a viable approach in assisting organizations in resolving conflicts. The data indicate that all of the health care organizations surveyed utilize some form of ADR to resolve conflict. The most common conflict resolution objective found is win/win, and respondents felt that ADR effectively met intended objectives. While the data gathered for this study are from a limited geographic region in Central Florida, the results can likely be generalized to many socially and ethnically diverse regions of the country.

  5. Numerical study on air turbines with enhanced techniques for OWC wave energy conversion

    Science.gov (United States)

    Cui, Ying; Hyun, Beom-Soo; Kim, Kilwon

    2017-10-01

    In recent years, the oscillating water column (OWC) wave energy converter, which can capture wave energy from the ocean, has been widely applied all over the world. As the essential part of the OWC system, the impulse and Wells turbines are capable of converting the low pressure pneumatic energy into the mechanical shaft power. As an enhanced technique, the design of endplate or ring attached to the blade tip is investigated numerically in this paper. 3D numerical models based on a CFD-software FLUENT 12.0 are established and validated by the corresponding experimental results from the reports of Setoguchi et al. (2004) and Takao et al. (2001). Then the flow fields and non-dimensional evaluating coefficients are calculated and analyzed under steady conditions. Results show that the efficiency of impulse turbine with ring can reach up to 0.49 when ϕ=1, which is 4% higher than that in the cases for the endplate-type and the original one. And the ring-type Wells turbine with fixed guide vanes shows the best performance with the maximal efficiency of 0.55, which is 22% higher than that of the original one. In addition, the quasi-steady analysis is used to calculate the mean efficiency and output-work of a wave cycle under sinusoidal flow condition. Taking all together, this study provides support for structural optimization of impulse turbine and Wells turbine in the future.

  6. Conversion of electric bell type furnace for natural gas usage: a case study

    Energy Technology Data Exchange (ETDEWEB)

    Ferraz, Andre D.; Machado Junior, Antonio R.; Rocha, Ivan C.C. da; Azevedo, Jorge G.W. de; Konishi, Ricardo; Lehmkuhl, Willian A. [Companhia de Gas de Santa Catarina (SCGAS), Florianopolis, SC (Brazil); Nunes, Andrea T.; Possamai, Talita S.; Nicolau, Vicente de P. [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil)

    2012-07-01

    In the present process of the heat treatment of normalizing of the crystalline structure of cast metal pieces, the heating is made by electric resistance arranged on the inner surfaces of the side walls of a bell furnace. Although electrical heating is suitable to obtain a uniform generation on the walls covered with electrical resistances, and is easy to control and operate with virtually no gas flow, it has some disadvantages such as poor movement of the heated ambient air, and higher cost. Heating occurs mostly by thermal radiation, with direct exchange between the resistors and the heated parts, but with a part serving as a barrier to the other, and with greater difficulty of heating the core loading. The details presented in this study, will simulate the process of heating by using electricity and using natural gas. In these simulations will be observed the distribution of temperature in the load and indoor over time and the rate of energy transferred to the load and also for the outside so to have a comparative processes. (author)

  7. Monte Carlo Studies of two Different Conversion Layers for Neutron Measurements with Medipix Silicon Detector.

    CERN Document Server

    Larsen, Andreas

    2013-01-01

    In 2007 the ventilation system of CNGS failed and investigations showed that the failure was due to Single Event Upset (SEU). Since then there has been increased interest in studies of neutron flux, that can potentially cause SEU. Two Medipix detectors have previously been installed in the CMS cavern on a test basis and have shown to work as intended[1]. More Medipix detectors will be installed to provide high resolution measurements of the particle flux in the vicinity of the CMS, focusing on measurements of the neutron flux. The measurements will provide an important basis to know what precautions to take to avoid another failure due to SEU. The measurements will also constitute a valuably reference to the FLUKA simulations of the general flux in the CMS cavern, that can potentially lead to important corrections of the simulations. Furthermore, measurements from the Medipix detectors will act as a cross check on the hadronic forward detector radiation monitoring system (HF radmon). Bonnos spheres are alread...

  8. A neutronic feasibility study for LEU conversion of the SAFARI-1 reactor

    International Nuclear Information System (INIS)

    Pond, R.B.; Hanan, N.A.; Matos, J.E.; Ball, G.

    2000-01-01

    A neutronic feasibility study to convert the SAFARI-1 reactor from HEU to LEU fuel was performed at Argonne National Laboratory in cooperation with NECSA. Comparisons were made of the reactor performance with the current 90% enriched HEU fuel type (UAl) and two 19.75% enriched LEU fuel types (U 3 Si 2 and U7Mo). The thermal fluxes with the LEU fuels were 3 - 9% lower than with the current HEU fuel. For the same fuel assembly design, a uranium density of approximately 4.5 g/cm 3 was required with U 3 Si 2 -Al fuel and a uranium density of about 4.6 g/cm 3 was required with U7Mo-Al fuel to match the 24.6-day cycle of the UAl-alloy fuel with 0.92 gU/cm 3 . The selection of a suitable LEU fuel and the decision to convert SAFARI-1 will be an economic matter that depends upon the fuel type, fuel assembly design, experiment performance and fuel cycle costs. (author)

  9. Experimental Study of a Small Scale Hydraulic System for Mechanical Wind Energy Conversion into Heat

    Directory of Open Access Journals (Sweden)

    Tadas Zdankus

    2016-07-01

    Full Text Available Significant potential for reducing thermal energy consumption in buildings of moderate and cold climate countries lies within wind energy utilisation. Unlike solar irradiation, character of wind speeds in Central and Northern Europe correspond to the actual thermal energy demand in buildings. However, mechanical wind energy undergoes transformation into electrical energy before being actually used as thermal energy in most wind energy applications. The study presented in this paper deals with hydraulic systems, designed for small-scale applications to eliminate the intermediate energy transformation as it converts mechanical wind energy into heat directly. The prototype unit containing a pump, flow control valve, oil tank and piping was developed and tested under laboratory conditions. Results of the experiments showed that the prototype system is highly efficient and adjustable to a broad wind velocity range by modifying the definite hydraulic system resistance. Development of such small-scale replicable units has the potential to promote “bottom-up” solutions for the transition to a zero carbon society.

  10. "Provoking conversations": case studies of organizations where Option Grid™ decision aids have become 'normalized'.

    Science.gov (United States)

    Scalia, Peter; Elwyn, Glyn; Durand, Marie-Anne

    2017-08-18

    Implementing patient decision aids in clinic workflow has proven to be a challenge for healthcare organizations and physicians. Our aim was to determine the organizational strategies, motivations, and facilitating factors to the routine implementation of Option Grid™ encounter decision aids at two independent settings. Case studies conducted by semi-structured interview, using the Normalization Process Theory (NPT) as a framework for thematic analysis. Twenty three interviews with physicians, nurses, hospital staff and stakeholders were conducted at: 1) CapitalCare Medical Group in Albany, New York; 2) HealthPartners Clinics in Minneapolis, Minnesota. 'Coherent' motivations were guided by financial incentives at CapitalCare, and by a 'champion' physician at HealthPartners. Nurses worked 'collectively' at both settings and played an important role at sites where successful implementation occurred. Some physicians did not understand the perceived utility of Option Grid™, which led to varying degrees of implementation success across sites. The appraisal work (reflexive monitoring) identified benefits, particularly in terms of information provision. Physicians at both settings, however, were concerned with time pressures and the suitability of the tool for patients with low levels of health literacy. Although both practice settings illustrated the mechanisms of normalization postulated by the theory, the extent to which Option Grid™ was routinely embedded in clinic workflow varied between sites, and between clinicians. Implementation of new interventions will require attention to an identified rationale (coherence), and to the collective action, cognitive participation, and assessment of value by organizational members of the organization.

  11. Initial implementation of the conversion from the energy-subtracted CT number to electron density in tissue inhomogeneity corrections: An anthropomorphic phantom study of radiotherapy treatment planning

    Energy Technology Data Exchange (ETDEWEB)

    Tsukihara, Masayoshi [Division of Radiological Technology, Graduate School of Health Sciences, Niigata University, Niigata 951-8518 (Japan); Noto, Yoshiyuki [Department of Radiology, Niigata University Medical and Dental Hospital, Niigata 951-8520 (Japan); Sasamoto, Ryuta; Hayakawa, Takahide; Saito, Masatoshi, E-mail: masaito@clg.niigata-u.ac.jp [Department of Radiological Technology, School of Health Sciences, Faculty of Medicine, Niigata University, Niigata 951-8518 (Japan)

    2015-03-15

    Purpose: To achieve accurate tissue inhomogeneity corrections in radiotherapy treatment planning, the authors had previously proposed a novel conversion of the energy-subtracted computed tomography (CT) number to an electron density (ΔHU–ρ{sub e} conversion), which provides a single linear relationship between ΔHU and ρ{sub e} over a wide range of ρ{sub e}. The purpose of this study is to present an initial implementation of the ΔHU–ρ{sub e} conversion method for a treatment planning system (TPS). In this paper, two example radiotherapy plans are used to evaluate the reliability of dose calculations in the ΔHU–ρ{sub e} conversion method. Methods: CT images were acquired using a clinical dual-source CT (DSCT) scanner operated in the dual-energy mode with two tube potential pairs and an additional tin (Sn) filter for the high-kV tube (80–140 kV/Sn and 100–140 kV/Sn). Single-energy CT using the same DSCT scanner was also performed at 120 kV to compare the ΔHU–ρ{sub e} conversion method with a conventional conversion from a CT number to ρ{sub e} (Hounsfield units, HU–ρ{sub e} conversion). Lookup tables for ρ{sub e} calibration were obtained from the CT image acquisitions for tissue substitutes in an electron density phantom (EDP). To investigate the beam-hardening effect on dosimetric uncertainties, two EDPs with different sizes (a body EDP and a head EDP) were used for the ρ{sub e} calibration. Each acquired lookup table was applied to two radiotherapy plans designed using the XiO TPS with the superposition algorithm for an anthropomorphic phantom. The first radiotherapy plan was for an oral cavity tumor and the second was for a lung tumor. Results: In both treatment plans, the performance of the ΔHU–ρ{sub e} conversion was superior to that of the conventional HU–ρ{sub e} conversion in terms of the reliability of dose calculations. Especially, for the oral tumor plan, which dealt with dentition and bony structures, treatment

  12. Conversion of Oleum papaveris seminis oil into methyl esters via esterification process: Optimization and kinetic study

    Directory of Open Access Journals (Sweden)

    Syam, A. M.

    2016-03-01

    Full Text Available This paper presents an acid pre-treatment process and a kinetic study for the esterification reaction of Oleum papaveris seminis oil with methanol in the presence of amberlite 120 as a solid catalyst to convert the oil into methyl esters. Response surface methodology (RSM was applied to optimize the reaction parameters, i.e. reaction time, percentage of the catalyst and volume ratio of methanol to oil. The results revealed that 0.87% w/w of catalyst concentration and 44.70% v/v of methanol to oil ratio provided final free fatty acid (FFA contents of 0.60% w/w at 102.40 min of reaction time. It proved that the contribution of Amberlite 120 in the esterification of FFA was highly significant. The kinetics of the esterification in Oleum papaveris seminis oil with methanol in the presence of the amberlite 120 catalyst were also investigated to establish the reaction rate constant (k, reaction order, and activation energy. The study was performed under the optimized parameters at three reaction temperatures (50, 55, and 60 ºC. The value of k was in the range of 0.013 to 0.027 min-1. The first-order kinetics’ model was suitable for this irreversible FFA esterification with the activation energy of about 60.9 KJ·mol-1.En este artículo se presenta un proceso de pre-tratamiento con ácido, y un estudio cinético de la reacción de esterificación. Se utiliza Oleum papaveris seminis con metanol en presencia de Amberlite 120 como catalizador sólido para la formación de los ésteres metílicos. Se aplicó una metodología de superficie de respuesta (RSM para optimizar los parámetros de la reacción; es decir, tiempo de reacción, porcentaje de la relación de catalizador y volumen de metanol - aceite. Los resultados mostraron que el 0,87% w/w de la concentración de catalizador y 44,70% v/v de metanol en relación al aceite dan lugar a un contenido final de ácidos grasos libres (FFA de 0,60% w/w en 102,40 min de tiempo de reacción. Se demostr

  13. A study of HANARO core conversion using high density U-Mo fuel

    International Nuclear Information System (INIS)

    Lee, K.H.; Lee, C.S.; Lee, B.C.; Park, S.J.; Kim, H.; Kim, C.K.

    2002-01-01

    Currently, HANARO is using 3.15gU/cc U3Si/Al as a driver fuel. HANARO has seven vertical irradiation holes in the core region. Three of them including a central trap are located in the inner region of the core and mainly being used for material irradiation tests. Four of them are located in the reflector tank but cooled by primary coolant. They are used for fuel irradiation tests or radioisotope development tests. For minimum core modification using high density U-Mo fuels, no dimension change is assumed in the current fuel rods and the cladding thickness remains the same in this study. The high density U-Mo fuel will have up to about twice the linear uranium loading of a current HANARO driver fuel. Using this high density fuel 8 fuel sites can be replaced with irradiation sites. Three kinds of conceptual cores are considered using 5 gU/cc U-7Mo/Al and 16 gU/cc U-7Mo. The increase of the linear heat generation rate due to the decrease of total fuel length can be overcome by more uniform radial and axial power distribution using different uranium densities and different fuel meat diameters are introduced into those cores. The new core has 4.54 times larger surface-to-volume ratio than the reference core. The core uranium loading, linear heat generation rate, excess reactivity, and control rod worth as well as the neutron spectra are analysed for each core. (author)

  14. CESR Conversion Damping Ring Studies of Electron Cloud Instabilities (CESR-TA)

    International Nuclear Information System (INIS)

    Rubin, David L.; Palmer, Mark A.

    2011-01-01

    In the International Linear Collider, two linear accelerators will accelerate bunches of positrons and electrons to over a hundred billion electron volts and collide them in a central detector. In order to obtain useful collision rates, the bunches, each containing twenty billion particles, must be compressed to a cross section of a few nanometers by a few hundred nanometers. In order to prepare these ultra high density bunches, damping rings (DRs) are employed before the linear accelerators. The DRs take the high emittance bunches that are provided by the electron and positron sources and, through the process of radiation damping, squeeze them into ultra low emittance beams that are ready for the main linear accelerators. In the damping rings, a number of effects can prevent the successful preparation of the beams. In the electron ring, an effect known as the fast ion instability can lead to beam growth and, in the positron ring, the build-up of an electron cloud (EC), which interacts with the circulating bunches, can produce the same effect. EC build-up and the subsequent interaction of the cloud with the positron beam in the DR have been identified as major risks for the successful construction of a linear collider. The CESRTA research program at the Cornell Electron Storage Ring (CESR) was developed in order to study the build-up of the EC, the details of its impact on ultra low emittance beams, as well as methods to mitigate the impact of the cloud. In the DR, the EC forms when synchrotron photons radiated from the circulating beam strike the walls of the vacuum chamber, resulting in the emission of photoelectrons. These low energy electrons can be accelerated across the vacuum chamber by the electric field of the beam, and strike the walls, causing the emission of secondary electrons. The secondary electrons are subsequently accelerated into the walls yet again via the same mechanism. The result is that the EC can rapidly begin to fill the vacuum chamber. In

  15. CESR Conversion Damping Ring Studies of Electron Cloud Instabilities (CESR-TA)

    Energy Technology Data Exchange (ETDEWEB)

    Rubin, David L.; Palmer, Mark A.

    2011-08-02

    In the International Linear Collider, two linear accelerators will accelerate bunches of positrons and electrons to over a hundred billion electron volts and collide them in a central detector. In order to obtain useful collision rates, the bunches, each containing twenty billion particles, must be compressed to a cross section of a few nanometers by a few hundred nanometers. In order to prepare these ultra high density bunches, damping rings (DRs) are employed before the linear accelerators. The DRs take the high emittance bunches that are provided by the electron and positron sources and, through the process of radiation damping, squeeze them into ultra low emittance beams that are ready for the main linear accelerators. In the damping rings, a number of effects can prevent the successful preparation of the beams. In the electron ring, an effect known as the fast ion instability can lead to beam growth and, in the positron ring, the build-up of an electron cloud (EC), which interacts with the circulating bunches, can produce the same effect. EC build-up and the subsequent interaction of the cloud with the positron beam in the DR have been identified as major risks for the successful construction of a linear collider. The CESRTA research program at the Cornell Electron Storage Ring (CESR) was developed in order to study the build-up of the EC, the details of its impact on ultra low emittance beams, as well as methods to mitigate the impact of the cloud. In the DR, the EC forms when synchrotron photons radiated from the circulating beam strike the walls of the vacuum chamber, resulting in the emission of photoelectrons. These low energy electrons can be accelerated across the vacuum chamber by the electric field of the beam, and strike the walls, causing the emission of secondary electrons. The secondary electrons are subsequently accelerated into the walls yet again via the same mechanism. The result is that the EC can rapidly begin to fill the vacuum chamber. In

  16. Alternatives in solar energy

    Science.gov (United States)

    Schueler, D. G.

    1978-01-01

    Although solar energy has the potential of providing a significant source of clean and renewable energy for a variety of applications, it is expected to penetrate the nation's energy economy very slowly. The alternative solar energy technologies which employ direct collection and conversion of solar radiation as briefly described.

  17. School Process and Teacher Job Satisfaction at Alternative Schools: A Multilevel Study Using SASS 2007-08 Data

    Science.gov (United States)

    Xia, Jiangang; Izumi, Masashi; Gao, Xingyuan

    2015-01-01

    This study examined the associations between public alternative schools' teacher job satisfaction and school processes. Based on a multilevel analysis of the national School and Staffing Survey 2007-08 data, we found that among the seven school processes, public alternative schools' administrative support, staff collegiality, career and working…

  18. Life Cycle Costing in Sustainability Assessment—A Case Study of Remanufactured Alternators

    Directory of Open Access Journals (Sweden)

    Annekatrin Lehmann

    2011-11-01

    Full Text Available Sustainability is on the international agenda, and is a driver for industry in international competition. Sustainability encompasses the three pillars: environment, society and economy. To prevent shifting of burden, the whole life cycle needs to be taken into account. For the environmental dimension of sustainability, life cycle assessment (LCA has been practiced for a while and is a standardized method. A life cycle approach for the social and economic pillars of sustainability needs to be further developed. This paper investigates the application of life cycle costing (LCC as part of a wider sustainability assessment where also social life cycle assessment (SLCA and LCA are combined. LCA-type LCC is applied on a case study of remanufactured alternators. Remanufacturing of automobile parts is a fast growing important business with large potential for cost and resource savings. Three design alternatives for the alternator and three locations for the remanufacturing plant are evaluated. The remanufacturer perspective and the user perspective are investigated. The results for the LCA-type LCC show that the largest cost for the remanufacturer is the new parts replacing old warn parts. However, the user cost, and therein especially, cost for fuel used for the alternator’s power production dominates and should be the focus for further improvement. In conducting the case study, it was revealed that the connection between the LCA-type LCC results and the economic dimension of sustainability needs to be further investigated and defined. For this purpose, areas of protection for life cycle sustainability assessment and LCA-type LCC in particular need further development.

  19. Study on the alternative mitigation of cement dust spread by capturing the dust with fogging method

    Science.gov (United States)

    Purwanta, Jaka; Marnoto, Tjukup; Setyono, Prabang; Handono Ramelan, Ari

    2017-12-01

    The existence of a cement plant impact the lives of people around the factory site. For example the air quality, which is polluted by dust. Cement plant has made various efforts to mitigate the generated dust, but there are still alot of dust fly inground either from the cement factory chimneys or transportation. The purpose of this study was to conduct a review of alternative mitigation of the spread of dust around the cement plant. This study uses research methods such as collecting secondary data which includes data of rain density, the average rains duration, wind speed and direction as well as data of dust intensity quality around PT. Semen Gresik (Persero) Tbk.Tuban plant. A soft Wind rose file is used To determine the wind direction propensity models. The impact on the spread of dust into the environment is determined using secondary data monitoring air quality. Results of the study is that the mitigation of dust around the cement plant is influenced by natural factors, such as the tendency of wind direction, rain fall and rainy days, and the rate of dust emission from the chimney. The alternative means proposed is an environmental friendly fogging dust catcher.

  20. The Effect of non-Newtonian Behavior of Fluid on the Tubular Reactor Performance and Studying Different Variables in Relation to the Degree of Conversion

    Directory of Open Access Journals (Sweden)

    Keivan Shayesteh

    2015-02-01

    Full Text Available In tubular reactors, there are different parameters which can affect the degree of conversion. The type of fluid motion and velocity profile of substances in the reactor are of most central measures. Different rheological models can be employed to study the behavior of fluids; power law model is one of the most commonly used models. In this study, the rheological behaviour of polymerization reaction of methyl methacrylate was examined. Due to the similarity function of tubular and batch reactors, the number of test tubes are used to prepare the solution. After preparation of the reactor solution, the n value of power law model was estimated within the span of 0.3492 to 0.9889 by curve fitting. Employing these rheological data, a reactor has been designed. Moreover, the effects of parameters such as reaction temperature, initiator wt%, the concentration of monomer and reactor’s radius on the degree of conversion have been studied. The obtained results in the research indicate a direct proportionality of conversion with the reaction temperature, initiator wt% and the concentration of monomer and also an inverse proportionality of conversion with reactor’s radius. Finally, the amount of conversion was obtained equal to 56.47% and according to its laboratory proportion which was 55.88% we have reached the conclusion that the modeling duly undertaken is applicable and valid.

  1. Parametric and alternative studies for fusion experimental reactor (FER) (FY 1984)

    International Nuclear Information System (INIS)

    1986-01-01

    Since 1980 the design study has been conducted at JAERI for the Fusion Experimental Reactor (FER) which has been proposed to be the next machine to JT-60 in the Japanese long term program of fusion reactor development. Starting from 1984 FER design is being reviewed and redesigned. This report is a part of the interim report which describes the results obtained in the review and redesign activities in FY 1984. This report includes the following parametric and alternative studies for the FER reference design: 1) parametric studies concerning with core plasma magnets, and operation scenario and power supply, 2) tritium breeding blanket, 3) the study for the steady state operation FER, 4) OTHERS. (AUTHOR)

  2. A Numerical Study on Mass Transfer and Methanol Conversion Efficiency According to Porosity and Temperature Change of Curved Channel Methanol-Steam Reformer

    International Nuclear Information System (INIS)

    Seong, Hong Seok; Lee, Chung Ho; Suh, Jeong Se

    2016-01-01

    Micro methanol-steam reformer for fuel cell can effectively produce hydrogen as reforming response to steam takes place in low temperature (less than 250℃). This study conducted numerical research on this reformer. First, study set wall temperature of the reformer at 100, 140, 180 and 220℃ while methanol conversion efficiency was set in 0, 0.072, 3.83 and 46.51% respectively. Then, porosity of catalyst was set in 0.1, 0.35, 0.6 and 0.85 and although there was no significant difference in methanol conversion efficiency, values of pressure drop were 4645.97, 59.50, 5.12 and 0.45 kPa respectively. This study verified that methanol-steam reformer rarely responds under the temperature of 180℃ and porosity does not have much effect on methanol conversion efficiency if the fluid flowing through reformer lowers activation energy by sufficiently contacting reformer.

  3. A Numerical Study on Mass Transfer and Methanol Conversion Efficiency According to Porosity and Temperature Change of Curved Channel Methanol-Steam Reformer

    Energy Technology Data Exchange (ETDEWEB)

    Seong, Hong Seok; Lee, Chung Ho; Suh, Jeong Se [Gyeongsang Nat’l Univ., Jinju (Korea, Republic of)

    2016-11-15

    Micro methanol-steam reformer for fuel cell can effectively produce hydrogen as reforming response to steam takes place in low temperature (less than 250℃). This study conducted numerical research on this reformer. First, study set wall temperature of the reformer at 100, 140, 180 and 220℃ while methanol conversion efficiency was set in 0, 0.072, 3.83 and 46.51% respectively. Then, porosity of catalyst was set in 0.1, 0.35, 0.6 and 0.85 and although there was no significant difference in methanol conversion efficiency, values of pressure drop were 4645.97, 59.50, 5.12 and 0.45 kPa respectively. This study verified that methanol-steam reformer rarely responds under the temperature of 180℃ and porosity does not have much effect on methanol conversion efficiency if the fluid flowing through reformer lowers activation energy by sufficiently contacting reformer.

  4. STUDY OF ALTERNATIVE FUELS AND EFFECTS OF COMPRESSION RATIO ON THERMAL EFFICIENCY AND ENGINE POWER

    Directory of Open Access Journals (Sweden)

    Sarjito Sarjito

    2017-01-01

    Full Text Available This paper was a case study during the sabatical program at Kingston University London in February 2007. It has been studied by team of motorsport automotive department Kingston University London and it has been elaborated as a final project on Master Program. This study takes into account some of the issues surrounding the debate about alcohol fuels in Motorsport and the wider automotive sector and is primarily concerned to add data where there seems to be little existing research since Motorsport is a secretive business. Motorsport plays an important part in the automotive industry and is a sport enjoyed worldwide. Racing practice is regarded as using the best available resources and technology as it requires optimal performance. The racing arena gives engineers the opportunity to test valuable technological solutions to prove their merits. Therefore, racing is the natural starting point for introducing new technological solutions to the public and could lead to the wholesale conversion to renewable fuels to meet our automotive energy needs. Alcohol has unique properties that make superior in many ways to ordinary gasoline. The higher knock resistance allows for higher compression ratios to be utilized resulting in higher power outputs and thermal efficiency. The efficient use of energy is of growing concern in all spheres of life and the automotive sector needs to be front runner in these efforts.

  5. Career conversations in vocational schools

    NARCIS (Netherlands)

    Mittendorff, K.M.; Brok, den P.J.; Beijaard, D.

    2010-01-01

    The purpose of this study was to examine career conversations between teachers and students in competence-based vocational education in the Netherlands. A total of 32 career conversations were observed and analysed with respect to four elements: content, teacher activities, student activities and

  6. Conversion from depression to bipolar disorder in a cohort of young people in England, 1999-2011: A national record linkage study.

    Science.gov (United States)

    James, Anthony; Wotton, Clare J; Duffy, Anne; Hoang, Uy; Goldacre, Michael

    2015-10-01

    To estimate the conversion rate from unipolar depression (ICD10 codes F32-F33) to bipolar disorder (BP) (ICD10 codes F31) in an English national cohort. It was hypothesised that early-onset BP (age disorder, with a more rapid, and higher rate of conversion from depression to BP. This record linkage study used English national Hospital Episode Statistics (HES) covering all NHS inpatient and day case admissions between 1999 and 2011. The overall rate of conversion from depression to BP for all ages was 5.65% (95% CI: 5.48-5.83) over a minimum 4-year follow-up period. The conversion rate from depression to BP increased in a linear manner with age from 10-14 years - 2.21% (95% C: 1.16-4.22) to 30-34 years - 7.06% (95% CI: 6.44-7.55) (F1,23=77.6, p=0.001, R(2)=0.77). The time to conversion was constant across the age range. The rate of conversion was higher in females (6.77%; 95% CI: 6.53-7.02) compared to males, (4.17%; 95% CI: 3.95-4.40) (χ(2)=194, pconversion rate from depression to bipolar disorder with age, and constant time for conversion across the age range does not support the notion that early-onset BP is a more severe form of the disorder. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Experimental and Theoretical Studies of the Acid-Catalyzed Conversion of Furfuryl Alcohol to Levulinic Acid in Aqueous Solution

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez Maldonado, Gretchen M.; Assary, Rajeev S.; Dumesic, James A.; Curtiss, Larry A.

    2012-02-14

    The conversion of furfuryl alcohol (FAL) to levulinic acid over Amberlyst TM 15 in aqueous media was investigated using a combination of liquid chromatography-mass spectrometry (LC-MS) measurements, isotopic labeling studies, nuclear magnetic resonance (NMR) spectroscopy, and ab initio quantum chemical calculations using the G4MP2 method. The results of these combined studies showed that one of the major reaction pathways takes place via a geminal diol species (4,5,5- trihydroxypentan-2-one, denoted as intermediate A), formed by the addition of two water molecules to FAL, where two of the oxygen atoms from FAL are retained. This geminal diol species can also be produced from another intermediate found to be a dimer-like species, denoted as intermediate B. This dimer-like species is formed at the early stages of reaction, and it can also be converted to intermediate A, indicating that intermediate B is the product of the reaction of FAL with another early intermediate. Quantum chemical calculations suggested this to be a protonated acyclic species. Reaction of this early intermediate with water produces intermediate A, while reaction with FAL produces intermediate B.

  8. Experimental and Theoretical Studies of the Acid-Catalyzed Conversion of Furfuryl Alcohol to Levulinic Acid in Aqueous Solution

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez Maldonado, Gretchen; Assary, Rajeev S.; Dumesic, James A; Curtiss, Larry A

    2012-01-01

    The conversion of furfuryl alcohol (FAL) to levulinic acid over AmberlystTM 15 in aqueous media was investigated using a combination of liquid chromatography-mass spectrometry (LC-MS) measurements, isotopic labeling studies, nuclear magnetic resonance (NMR) spectroscopy, and ab initio quantum chemical calculations using the G4MP2 method. The results of these combined studies showed that one of the major reaction pathways takes place via a geminal diol species (4,5,5-trihydroxypentan-2-one, denoted as intermediate A), formed by the addition of two water molecules to FAL, where two of the oxygen atoms from FAL are retained. This geminal diol species can also be produced from another intermediate found to be a dimer-like species, denoted as intermediate B. This dimer-like species is formed at the early stages of reaction, and it can also be converted to intermediate A, indicating that intermediate B is the product of the reaction of FAL with another early intermediate. Quantum chemical calculations suggested this to be a protonated acyclic species. Reaction of this early intermediate with water produces intermediate A, while reaction with FAL produces intermediate B.

  9. Conversion program in Sweden

    Energy Technology Data Exchange (ETDEWEB)

    Jonsson, E.B. [Studsvik Nuclear AB, Nykoeping (Sweden)

    1997-08-01

    The conversion of the Swedish 50 MW R2 reactor from HEU to LEU fuel has been successfully accomplished over a 16 cycles long process. The conversion started in January 1991 with the introduction of 6 LEU assemblies in the 8*8 core. The first all LEU core was loaded in March 1993 and physics measurements were performed for the final licensing reports. A total of 142 LEU fuel assemblies have been irradiated up until September 1994 without any fuel incident. The operating licence for the R2 reactor was renewed in mid 1994 taking into account new fuel type. The Swedish Nuclear Inspectorate (SKI) pointed out one crucial problem with the LEU operation, that the back end of the LEU fuel cycle has not yet been solved. For the HEU fuel Sweden had the reprocessing alternative. The country is now relying heavily on the success of the USDOEs Off Site Fuels Policy to take back the spent fuel from the research reactors. They have in the meantime increased their intermediate storage facilities. There is, however, a limit both in time and space for storage of MTR-type of assemblies in water. The penalty of the lower thermal neutron flux in LEU cores has been reduced by improvements of the new irradiation rigs and by fine tuning the core calculations. The Studsvik code package, CASMO-SIMULATE, widely used for ICFM in LWRs has been modified to suit the compact MTR type of core.

  10. Advanced Transportation System Studies. Technical Area 3: Alternate Propulsion Subsystem Concepts. Volume 1; Executive Summary

    Science.gov (United States)

    Levack, Daniel J. H.

    2000-01-01

    The Alternate Propulsion Subsystem Concepts contract had seven tasks defined that are reported under this contract deliverable. The tasks were: FAA Restart Study, J-2S Restart Study, Propulsion Database Development. SSME Upper Stage Use. CERs for Liquid Propellant Rocket Engines. Advanced Low Cost Engines, and Tripropellant Comparison Study. The two restart studies, F-1A and J-2S, generated program plans for restarting production of each engine. Special emphasis was placed on determining changes to individual parts due to obsolete materials, changes in OSHA and environmental concerns, new processes available, and any configuration changes to the engines. The Propulsion Database Development task developed a database structure and format which is easy to use and modify while also being comprehensive in the level of detail available. The database structure included extensive engine information and allows for parametric data generation for conceptual engine concepts. The SSME Upper Stage Use task examined the changes needed or desirable to use the SSME as an upper stage engine both in a second stage and in a translunar injection stage. The CERs for Liquid Engines task developed qualitative parametric cost estimating relationships at the engine and major subassembly level for estimating development and production costs of chemical propulsion liquid rocket engines. The Advanced Low Cost Engines task examined propulsion systems for SSTO applications including engine concept definition, mission analysis. trade studies. operating point selection, turbomachinery alternatives, life cycle cost, weight definition. and point design conceptual drawings and component design. The task concentrated on bipropellant engines, but also examined tripropellant engines. The Tripropellant Comparison Study task provided an unambiguous comparison among various tripropellant implementation approaches and cycle choices, and then compared them to similarly designed bipropellant engines in the

  11. Energy conversion and utilization technologies

    International Nuclear Information System (INIS)

    1988-01-01

    The DOE Energy Conversion and Utilization Technologies (ECUT) Program continues its efforts to expand the generic knowledge base in emerging technological areas that support energy conservation initiatives by both the DOE end-use sector programs and US private industry. ECUT addresses specific problems associated with the efficiency limits and capabilities to use alternative fuels in energy conversion and end-use. Research is aimed at understanding and improving techniques, processes, and materials that push the thermodynamic efficiency of energy conversion and usage beyond the state of the art. Research programs cover the following areas: combustion, thermal sciences, materials, catalysis and biocatalysis, and tribology. Six sections describe the status of direct contact heat exchange; the ECUT biocatalysis project; a computerized tribology information system; ceramic surface modification; simulation of internal combustion engine processes; and materials-by-design. These six sections have been indexed separately for inclusion on the database. (CK)

  12. GACT: a Genome build and Allele definition Conversion Tool for SNP imputation and meta-analysis in genetic association studies.

    Science.gov (United States)

    Sulovari, Arvis; Li, Dawei

    2014-07-19

    Genome-wide association studies (GWAS) have successfully identified genes associated with complex human diseases. Although much of the heritability remains unexplained, combining single nucleotide polymorphism (SNP) genotypes from multiple studies for meta-analysis will increase the statistical power to identify new disease-associated variants. Meta-analysis requires same allele definition (nomenclature) and genome build among individual studies. Similarly, imputation, commonly-used prior to meta-analysis, requires the same consistency. However, the genotypes from various GWAS are generated using different genotyping platforms, arrays or SNP-calling approaches, resulting in use of different genome builds and allele definitions. Incorrect assumptions of identical allele definition among combined GWAS lead to a large portion of discarded genotypes or incorrect association findings. There is no published tool that predicts and converts among all major allele definitions. In this study, we have developed a tool, GACT, which stands for Genome build and Allele definition Conversion Tool, that predicts and inter-converts between any of the common SNP allele definitions and between the major genome builds. In addition, we assessed several factors that may affect imputation quality, and our results indicated that inclusion of singletons in the reference had detrimental effects while ambiguous SNPs had no measurable effect. Unexpectedly, exclusion of genotypes with missing rate > 0.001 (40% of study SNPs) showed no significant decrease of imputation quality (even significantly higher when compared to the imputation with singletons in the reference), especially for rare SNPs. GACT is a new, powerful, and user-friendly tool with both command-line and interactive online versions that can accurately predict, and convert between any of the common allele definitions and between genome builds for genome-wide meta-analysis and imputation of genotypes from SNP-arrays or deep

  13. Study of the standard direct costs of various techniques of advanced endoscopy. Comparison with surgical alternatives.

    Science.gov (United States)

    Loras, Carme; Mayor, Vicenç; Fernández-Bañares, Fernando; Esteve, Maria

    2018-03-12

    The complexity of endoscopy has carried out an increase in cost that has a direct effect on the healthcare systems. However, few studies have analyzed the cost of advanced endoscopic procedures (AEP). To carry out a calculation of the standard direct costs of AEP, and to make a financial comparison with their surgical alternatives. Calculation of the standard direct cost in carrying out each procedure. An endoscopist detailed the time, personnel, materials, consumables, recovery room time, stents, pathology and medication used. The cost of surgical procedures was the average cost recorded in the hospital. Thirty-eight AEP were analyzed. The technique showing lowest cost was gastroscopy + APC (€116.57), while that with greatest cost was ERCP with cholangioscopy + stent placement (€5083.65). Some 34.2% of the procedures registered average costs of €1000-2000. In 57% of cases, the endoscopic alternative was 2-5 times more cost-efficient than surgery, in 31% of cases indistinguishable or up to 1.4 times more costly. Standard direct cost of the majority of AEP is reported using a methodology that enables easy application in other centers. For the most part, endoscopic procedures are more cost-efficient than the corresponding surgical procedure. Copyright © 2018 The Author(s). Published by Elsevier Ltd.. All rights reserved.

  14. Effects of propranolol on conversational reciprocity in autism spectrum disorder: a pilot, double-blind, single-dose psychopharmacological challenge study.

    Science.gov (United States)

    Zamzow, Rachel M; Ferguson, Bradley J; Stichter, Janine P; Porges, Eric C; Ragsdale, Alexandra S; Lewis, Morgan L; Beversdorf, David Q

    2016-04-01

    Pharmacological intervention for autism spectrum disorder (ASD) is an important addition to treatment, yet currently available agents target co-morbid psychiatric concerns, such as aggression and irritability. Propranolol, a beta-adrenergic antagonist with anxiolytic effects, has been shown to improve verbal fluency and working memory in adults and adolescents with ASD in single-dose challenges. The present pilot study explores the acute effects of propranolol on a measure of conversational reciprocity in this population. We also examined whether autonomic activity and anxiety moderate or mediate response to the drug, given relationships between these variables and ASD, as well as the drug's effects. In a within-subject crossover design, 20 individuals with ASD received a single dose of propranolol or placebo during two sessions in a double-blinded, counterbalanced manner. After drug administration, participants performed a conversational reciprocity task by engaging in a short conversation with the researcher. Measurements of autonomic activity and anxiety were obtained before and after drug administration. Propranolol significantly improved performance on the conversational reciprocity task total [d = 0.40] and nonverbal communication domain scores when compared to the placebo condition. However, neither autonomic activity nor anxiety was significantly associated with drug response. Acute propranolol administration improved conversational reciprocity in ASD. Further exploration of these preliminary findings, as well as other potential treatment response predictors, with serial doses is warranted.

  15. Alternative Fuels Data Center: Hybrid and Plug-In Electric Vehicle

    Science.gov (United States)

    Conversions Hybrid and Plug-In Electric Vehicle Conversions to someone by E-mail Share Alternative Fuels Data Center: Hybrid and Plug-In Electric Vehicle Conversions on Facebook Tweet about Alternative Fuels Data Center: Hybrid and Plug-In Electric Vehicle Conversions on Twitter Bookmark Alternative

  16. A First Case Study of a Life Cycle-Based Alternatives Assessment (LCAA)

    DEFF Research Database (Denmark)

    Fantke, Peter; Huang, L.; Overcash, Michael

    2017-01-01

    cycle impacts. Our approach is evaluated in a case study, through which we outline future research needs to fully operationalize a consistent and Life Cycle-based Alternatives Assessment (LCAA). We build on a flexible mass balance-based modeling system yielding cumulative multimedia transfer fractions...... and exposure pathway-specific Product Intake Fractions defined as chemical mass taken in by humans per unit mass of chemical in a product. When combined with chemical masses in products and further with toxicity information, this approach is a resourceful way to inform AA. Our case study reveals that replacing...... various population groups including workers, consumers and the general public, while life cycle impacts need to focus on categories relevant for a given AA chemical-product application. We systematically define the scope of AA and identify key elements for quantitatively considering exposure and life...

  17. Carbon offsets as an economic alternative to large-scale logging: a case study in Guyana

    Energy Technology Data Exchange (ETDEWEB)

    Osborne, T. [Energy and Resources Group, University of California Berkeley, 310 Barrows Hall, Berkeley CA 94720 (United States); Kiker, C. [Food and Resource Economics Department, University of Florida, PO Box 110240, Gainesville, FL 32611 (United States)

    2005-03-01

    The objective of this study is to analyze the economic viability of carbon-offset projects that avoid logging in Guyana's forests. The results of this case study illustrate the cost effectiveness of alternative land-use options that reduce deforestation and associated greenhouse gas (GHG) emissions. This analysis demonstrates that using Guyana's rainforests for climate change mitigation can generate equivalent revenue to that of conventional large-scale logging without detrimental environmental impacts. At a 12% discount rate, the break-even price for carbon is estimated to be about US$ 0.20/tC. This estimate falls toward the low range of carbon prices for existing carbon offset projects that avoid deforestation.

  18. Experimental studies on the elimination of minimal residual leukemia in vivo by alternate half body irradiation

    International Nuclear Information System (INIS)

    Chu Jianxin

    1992-01-01

    The purpose of this study is to develop a new way for leukemia patients to tolerate an ablative chemoradiotherapy without BMT. Previous studies had demonstrated that only a few leukemia cells remained in the body during remission phase following chemotherapy and did not migrate to distant organs via the circulation until they had given rise to 3 ∼ 4 x 10 5 new cells. The period required for such growth was about 20 days. However, hematopoietic stem cells migrate earlier than do leukemia cells. Therefore, alternate half body irradiation (HBI) within this period would kill the residual leukemia cells, but hematopoietic stem cells would migrate from shielded marrow to irradiated marrow and reconstruct hematopoiesis

  19. [Neuropsychological assessment in conversion disorder].

    Science.gov (United States)

    Demır, Süleyman; Çelıkel, Feryal Çam; Taycan, Serap Erdoğan; Etıkan, İlker

    2013-01-01

    Conversion disorder is characterized by functional impairment in motor, sensory, or neurovegetative systems that cannot be explained by a general medical condition. Diagnostic systems emphasize the absence of an organic basis for the dysfunction observed in conversion disorder. Nevertheless, there is a growing body of data on the specific functional brain correlates of conversion symptoms, particularly those obtained via neuroimaging and neurophysiological assessment. The present study aimed to determine if there are differences in measures of cognitive functioning between patients with conversion disorder and healthy controls. The hypothesis of the study was that the patients with conversion disorder would have poorer neurocognitive performance than the controls. The patient group included 43 patients diagnosed as conversion disorder and other psychiatric comorbidities according to DSM-IV-TR. Control group 1 included 44 patients diagnosed with similar psychiatric comorbidities, but not conversion diosorder, and control group 2 included 43 healthy individuals. All participants completed a sociodemographic questionnaire and were administered the SCID-I and a neuropsychological test battery of 6 tests, including the Serial Digit Learning Test (SDLT), Auditory Verbal Learning Test (AVLT), Wechsler Memory Scale, Stroop Color Word Interference Test, Benton Judgment of Line Orientation Test (BJLOT), and Cancellation Test. The patient group had significantly poorer performance on the SDLT, AVLT, Stroop Color Word Interference Test, and BJLOT than both control groups. The present findings highlight the differences between the groups in learning and memory, executive and visuospatial functions, and attention, which seemed to be specific to conversion disorder.

  20. A comparative study of nitrogen conversion during pyrolysis of coconut fiber, its corresponding biochar and their blends with lignite.

    Science.gov (United States)

    Liu, Zhengang; Balasubramanian, Rajasekhar

    2014-01-01

    In the present study, the conversion of fuel-N to HCN and NH3 was investigated during rapid pyrolysis of raw biomass (coconut fiber), its corresponding biochar and their blends with lignite within a temperature range of 600-900°C. The results showed that the raw biomass and the biochar showed totally different nitrogen partitioning between NH3 and HCN. HCN was the dominant nitrogen pollutant from pyrolysis of raw biomass, while for the biochar pyrolysis the yield of NH3 was slightly higher than that of HCN. Synergistic interactions occurred within both raw biomass/lignite and biochar/lignite blends, especially for the biochar/lignite blend, and resulted in reduced yields of HCN and NH3, decreased the total nitrogen percentage retained in the char and promoted harmless N2 formation. These findings suggest that biochar/lignite co-firing for energy production may have the enhanced benefit of reduced emissions of nitrogen pollutants than raw biomass/lignite. Copyright © 2013 Elsevier Ltd. All rights reserved.

  1. Experimental and Modeling Studies on the Conversion of Inulin to 5-Hydroxymethylfurfural Using Metal Salts in Water

    Directory of Open Access Journals (Sweden)

    Boy Arief Fachri

    2015-12-01

    Full Text Available Inulin, a plant polysaccharide consisting of mainly d-fructose units, is considered an interesting feed for 5-hydroxymethylfurfural (HMF, a top 12 bio-based chemical. We here report an exploratory experimental study on the use of a wide range of homogeneous metal salts as catalysts for the conversion of inulin to HMF in water. Best results were obtained using CuCl2. Activity-pH relations indicate that the catalyst activity of CuCl2 is likely related to Lewis acidity and not to Brönsted acidity. The effects of process conditions on HMF yield for CuCl2 were systematically investigated and quantified using a central composite design (160–180 °C, an inulin loading between 0.05 and 0.15 g/mL, CuCl2 concentration in range of 0.005–0.015 M, and a reaction time between 10 and 120 min. The highest experimental HMF yield in the process window was 30.3 wt. % (39 mol %, 180 °C, 0.05 g/mL inulin, 0.005 M CuCl2 and a reaction time of 10 min. The HMF yields were modelled using non-linear, multi variable regression and good agreement between experimental data and model were obtained.

  2. Role of water in the enzymatic catalysis: study of ATP + AMP → 2ADP conversion by adenylate kinase.

    Science.gov (United States)

    Adkar, Bharat V; Jana, Biman; Bagchi, Biman

    2011-04-28

    The catalytic conversion ATP + AMP → 2ADP by the enzyme adenylate kinase (ADK) involves the binding of one ATP molecule to the LID domain and one AMP molecule to the NMP domain. The latter is followed by a phosphate transfer and then the release of two ADP molecules. We have computed a novel two-dimensional configurational free energy surface (2DCFES), with one reaction coordinate each for the LID and the NMP domain motions, while considering explicit water interactions. Our computed 2DCFES clearly reveals the existence of a stable half-open half-closed (HOHC) intermediate state of the enzyme. Cycling of the enzyme through the HOHC state reduces the conformational free energy barrier for the reaction by about 20 kJ/mol. We find that the stability of the HOHC state (missed in all earlier studies with implicit solvent model) is largely because of the increase of specific interactions of the polar amino acid side chains with water, particularly with the arginine and the histidine residues. Free energy surface of the LID domain is rather rugged, which can conveniently slow down LID's conformational motion, thus facilitating a new substrate capture after the product release in the catalytic cycle.

  3. Rating Instructional Conversations: A Guide

    OpenAIRE

    Rueda, Robert; Goldenberg, Claude; Gallimore, Ronald

    1992-01-01

    The current focus on more effective ways to foster literacy in school-age children, especially language minority students, has led to the development of alternative instructional approaches. One such approach is the instructional conversation (IC), based on early work in the Hawaiian Kamehameha Elementary Education Project (KEEP), on neo-Vygotskian theory, and on recent classroom-based research on reading comprehension. The present report outlines preliminary efforts to operationaliz...

  4. Alternate superior Julia sets

    International Nuclear Information System (INIS)

    Yadav, Anju; Rani, Mamta

    2015-01-01

    Alternate Julia sets have been studied in Picard iterative procedures. The purpose of this paper is to study the quadratic and cubic maps using superior iterates to obtain Julia sets with different alternate structures. Analytically, graphically and computationally it has been shown that alternate superior Julia sets can be connected, disconnected and totally disconnected, and also fattier than the corresponding alternate Julia sets. A few examples have been studied by applying different type of alternate structures

  5. Project Alternative Systems Study - PASS. Analysis of performance and long-term safety of repository concepts

    International Nuclear Information System (INIS)

    Birgersson, L.; Skagius, K.; Wiborgh, M.; Widen, H.

    1992-09-01

    This study is part of the Project on Alternative Systems Study, PASS, with the overall aim to perform a technical/economical ranking of alternative repository concepts and canisters for the final storage of spent nuclear fuel. The comparison should in the first stage separately assess technology in construction and operation, long-term performance and safety, and costs. Three of the repository concepts are assumed to be located at a depth of approximately 500 m in the host rock, KBS-3, Very Long Holes (VLH) and Medium Long Holes (MLH). In the KBS-3 concept the canisters are deposited in vertical deposition holes in a system of parallel storage tunnels. In the VLH concept larger canisters are deposited in long horizontal tunnels. The MLH concept, is an evolution of the two other concepts, with KBS-3 type canisters deposited in horizontal tunnels. Smaller canisters are to be deposited in deep bore holes at a depth between 2000 to 4000 m in the Very Deep Holes (VDH) concept. In all concepts the canisters will be surrounded by a bentonite buffer. The aim of the present study is to analyze and compare the performance and long-term safety of the repository concepts. Only a qualitative comparison of the concepts is made as no calculations of radionuclide releases or dose to man have been performed. The ranking of the repository concepts was carried out by comparing the VDH, VLH and MLH concept with the KBS-3 concept. The performance and long-term safety of the repositories located at 500 m level will be based on a multiple barrier system and the predictions for the concepts will involve similar uncertainties. (54 refs.)

  6. Alternative security

    International Nuclear Information System (INIS)

    Weston, B.H.

    1990-01-01

    This book contains the following chapters: The Military and Alternative Security: New Missions for Stable Conventional Security; Technology and Alternative Security: A Cherished Myth Expires; Law and Alternative Security: Toward a Just World Peace; Politics and Alternative Security: Toward a More Democratic, Therefore More Peaceful, World; Economics and Alternative Security: Toward a Peacekeeping International Economy; Psychology and Alternative Security: Needs, Perceptions, and Misperceptions; Religion and Alternative Security: A Prophetic Vision; and Toward Post-Nuclear Global Security: An Overview

  7. A Study of Mars Dust Environment Simulation at NASA Johnson Space Center Energy Systems Test Area Resource Conversion Test Facility

    Science.gov (United States)

    Chen, Yuan-Liang Albert

    1999-01-01

    The dust environment on Mars is planned to be simulated in a 20 foot thermal-vacuum chamber at the Johnson Space Center, Energy Systems Test Area Resource Conversion Test Facility in Houston, Texas. This vacuum chamber will be used to perform tests and study the interactions between the dust in Martian air and ISPP hardware. This project is to research, theorize, quantify, and document the Mars dust/wind environment needed for the 20 foot simulation chamber. This simulation work is to support the safety, endurance, and cost reduction of the hardware for the future missions. The Martian dust environment conditions is discussed. Two issues of Martian dust, (1) Dust Contamination related hazards, and (2) Dust Charging caused electrical hazards, are of our interest. The different methods of dust particles measurement are given. The design trade off and feasibility were studied. A glass bell jar system is used to evaluate various concepts for the Mars dust/wind environment simulation. It was observed that the external dust source injection is the best method to introduce the dust into the simulation system. The dust concentration of 30 Mg/M3 should be employed for preparing for the worst possible Martian atmosphere condition in the future. Two approaches thermal-panel shroud for the hardware conditioning are discussed. It is suggested the wind tunnel approach be used to study the dust charging characteristics then to be apply to the close-system cyclone approach. For the operation cost reduction purpose, a dehumidified ambient air could be used to replace the expensive CO2 mixture for some tests.

  8. Selection of the Best Alternative of Heating System by Environmental Impact Assessment—Case Study

    Directory of Open Access Journals (Sweden)

    Vlasta Ondrejka Harbulakova

    2018-01-01

    Full Text Available The Framework Directive 2009/28/EC on the promotion of the use of energy from renewable sources aims at developing the local and regional electricity market in order to reduce greenhouse gas emissions. A comparison study of the proposed activities of construction of a new biomass-fired power plant or reconstruction of an old one-gas power plant in town located in eastern Slovakia is presented in this paper. The method of the index coefficient was used for choosing the best alternatives. Multicriteria analysis proved that the construction of biomass-fired power plant is the most suitable solution chosen from three assessed variants (no activity is implemented, biomass power plant and modernized gas boiler.

  9. Preliminary design study of an alternate heat source assembly for a Brayton isotope power system

    Science.gov (United States)

    Strumpf, H. J.

    1978-01-01

    Results are presented for a study of the preliminary design of an alternate heat source assembly (HSA) intended for use in the Brayton isotope power system (BIPS). The BIPS converts thermal energy emitted by a radioactive heat source into electrical energy by means of a closed Brayton cycle. A heat source heat exchanger configuration was selected and optimized. The design consists of a 10 turn helically wound Hastelloy X tube. Thermal analyses were performed for various operating conditions to ensure that post impact containment shell (PICS) temperatures remain within specified limits. These limits are essentially satisfied for all modes of operation except for the emergency cooling system for which the PICS temperatures are too high. Neon was found to be the best choice for a fill gas for auxiliary cooling system operation. Low cycle fatigue life, natural frequency, and dynamic loading requirements can be met with minor modifications to the existing HSA.

  10. Taking a case study approach to assessing alternative leadership models in health care.

    Science.gov (United States)

    Harris, Jonathan; Mayo, Paula

    2018-06-14

    Good leadership is essential to patient-centred care and staff satisfaction in the healthcare environment. All members of the healthcare team can be leaders and evidence-based theory should inform their leadership practice. This article uses a case study approach to critically evaluate leadership as exercised by a charge nurse and a student nurse in a clinical scenario. Ineffective leadership styles are identified and alternatives proposed; considerable attention is given to critiquing both 'heroic' and 'post-heroic' transformational leadership theories. The concept of power will also be discussed, as power and leadership are closely related, and the importance of empowering members of the healthcare team through altering organisational structure is emphasised. This article advocates leadership that encourages innovation, enhances patient-centred care, encourages excellence and has ethical integrity. Recommendations of appropriate models of leadership are provided, while existing gaps in the healthcare leadership literature are highlighted.

  11. Study of greenhouse gases reduction alternatives for the exploitation of non conventional oil sands in Canada

    Energy Technology Data Exchange (ETDEWEB)

    Bouchonneau, Deborah [Institut Francais du Petrole (IFP), Paris (France)

    2008-07-01

    High energy prices and greenhouse gases reduction represent the main challenges the current worldwide energetic situation has to face. As a consequence, paradox strategies can be highlighted: oil prices are sufficiently high to exploit non conventional oil resources, like extra heavy oils and oil sands. But the production of these resources emits larger GHG than the conventional oil path and implies other major environmental issues (water management, risks of soil pollution, destruction of the boreal forest), incompatible with the rules validated by the protocol of Kyoto. At the light of the new greenhouse gases reduction regulation framework announced by the Canadian Federal government, this work focuses on the study of greenhouse gases reduction alternatives applied to the non conventional oil sands exploitation in Canada. (author)

  12. Oral Narrative Genres as Dialogic Resources for Classroom Literature Study: A Contextualized Case Study of Conversational Narrative Discussion

    Science.gov (United States)

    Juzwik, Mary M.; Nystrand, Martin; Kelly, Sean; Sherry, Michael B.

    2008-01-01

    Five questions guided a case study exploring the relationship between oral narrative and discussion in middle school literature study: (a) Relative to similar classrooms in a large-scale study, how can overall literature instruction be characterized? (b) Relative to similar classrooms in a large-scale study, how well do students achieve in the…

  13. Experimental and Kinetic Modeling Studies on the Conversion of Sucrose to Levulinic Acid and 5-Hydroxymethylfurfural Using Sulfuric Acid in Water

    NARCIS (Netherlands)

    Tan-Soetedjo, Jenny N. M.; van de Bovenkamp, Henk H.; Abdilla, Ria M.; Rasrendra, Carolus B.; van Ginkel, Jacob; Heeres, Hero J.

    2017-01-01

    We here report experimental and kinetic modeling studies on the conversion of sucrose to levulinic acid (LA) and 5-hydroxymethylfurfural (HMF) in water using sulfuric acid as the catalyst. Both compounds are versatile building blocks for the synthesis of various biobased (bulk) chemicals. A total of

  14. Experimental and Kinetic Modeling Studies on the Sulfuric Acid Catalyzed Conversion of D-Fructose to 5-Hydroxymethylfurfural and Levulinic Acid in Water

    NARCIS (Netherlands)

    Fachri, Boy A.; Abdilla, Ria M.; van de Bovenkamp, Henk H.; Rasrendra, Carolus B.; Heeres, Hero J.

    2015-01-01

    Levulinic acid (LA) and 5-hydroxymethylfurfural (HMF) have been identified as promising biomass-derived platform chemicals. A kinetic study on the conversion of D-fructose to HMF and LA in water using sulfuric acid as the catalyst has been performed in batch setups. The experiments were carried out

  15. A Planning Study for the Conversion of Recorded Books and Magazines from Rigid Discs to Cassettes and Flexible Discs. Final Report.

    Science.gov (United States)

    Innovative Systems Research, Inc., Pennsauken, NJ.

    Twelve different conversion plans were delineated and evaluated in the performance of this study effort. An indepth technical, financial, and cost/benefit analysis was included. One plan was determined to be distinctively more cost-effective than any of the other plans because it provided a technically feasible system that assured the maximum…

  16. 'I Already Have a Culture.' Negotiating Competing Grand and Personal Narratives in Interview Conversations with New Study Abroad Arrivals

    Science.gov (United States)

    Amadasi, Sara; Holliday, Adrian

    2018-01-01

    In an interview with a postgraduate student about her intercultural experience of recently arriving for study abroad, it was found that the two researchers and the student were engaged in a mutual exploration of cultural identity. The interview events became conversational and took the form of small culture formation on the go in which each…

  17. Environmental assessment of alternative municipal solid waste management strategies. A Spanish case study.

    Science.gov (United States)

    Bovea, M D; Ibáñez-Forés, V; Gallardo, A; Colomer-Mendoza, F J

    2010-11-01

    The aim of this study is to compare, from an environmental point of view, different alternatives for the management of municipal solid waste generated in the town of Castellón de la Plana (Spain). This town currently produces 207 ton of waste per day and the waste management system employed today involves the collection of paper/cardboard, glass and light packaging from materials banks and of rest waste at street-side containers. The proposed alternative scenarios were based on a combination of the following elements: selective collection targets to be accomplished by the year 2015 as specified in the Spanish National Waste Plan (assuming they are reached to an extent of 50% and 100%), different collection models implemented nationally, and diverse treatments of both the separated biodegradable fraction and the rest waste to be disposed of on landfills. This resulted in 24 scenarios, whose environmental behaviour was studied by applying the life cycle assessment methodology. In accordance with the ISO 14040-44 (2006) standard, an inventory model was developed for the following stages of the waste management life cycle: pre-collection (bags and containers), collection, transport, pre-treatment (waste separation) and treatment/disposal (recycling, composting, biogasification+composting, landfill with/without energy recovery). Environmental indicators were obtained for different impact categories, which made it possible to identify the key variables in the waste management system and the scenario that offers the best environmental behaviour. Finally, a sensitivity analysis was used to test some of the assumptions made in the initial life cycle inventory model. Copyright © 2010 Elsevier Ltd. All rights reserved.

  18. Oxidative degradation of alternative gasoline oxygenates in aqueous solution by ultrasonic irradiation: Mechanistic study

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Duk Kyung, E-mail: dkim@aum.edu [Department of Physical Science, Auburn University Montgomery, Montgomery, AL 36117 (United States); O' Shea, Kevin E., E-mail: osheak@fiu.edu [Department of Chemistry and Biochemistry, Florida International University, University Park, Miami, FL 33199 (United States); Cooper, William J. [Department of Civil and Environmental Engineering, Urban Water Research Center, University of California Irvine, Irvine, CA 92697-2175 (United States)

    2012-07-15

    Widespread pollution has been associated with gasoline oxygenates of branched ethers methyl tert-butyl ether (MTBE), di-isopropyl ether (DIPE), ethyl tert-butyl ether (ETBE), and tert-amyl ether (TAME) which enter groundwater. The contaminated plume develops rapidly and treatment for the removal/destruction of these ethers is difficult when using conventional methods. Degradation of MTBE, with biological methods and advanced oxidation processes, are rather well known; however, fewer studies have been reported for degradation of alternative oxygenates. Degradation of alternative gasoline oxygenates (DIPE, ETBE, and TAME) by ultrasonic irradiation in aqueous oxygen saturation was investigated to elucidate degradation pathways. Detailed degradation mechanisms are proposed for each gasoline oxygenate. The common major degradation pathways are proposed to involve abstraction of {alpha}-hydrogen atoms by hydroxyl radicals generated during ultrasound cavitation and low temperature pyrolytic degradation of ETBE and TAME. Even some of the products from {beta}-H abstraction overlap with those from high temperature pyrolysis, the effect of {beta}-H abstraction was not shown clearly from product study because of possible 1,5 H-transfer inside cavitating bubbles. Formation of hydrogen peroxide and organic peroxides was also determined during sonolysis. These data provide a better understanding of the degradation pathways of gasoline oxygenates by sonolysis in aqueous solutions. The approach may also serve as a model for others interested in the details of sonolysis. - Highlights: Black-Right-Pointing-Pointer Gasoline oxygenates (ETBE, TAME, DIPE) were completely degraded after 6 hours under ultrasonic irradiation in O{sub 2} saturation. Black-Right-Pointing-Pointer The major degradation pathways were proposed to involve abstraction of {alpha}-hydrogen atoms by hydroxyl radicals and low temperature pyrolytic degradation. Black-Right-Pointing-Pointer The effect of {beta

  19. Perception of co-speech gestures in aphasic patients: a visual exploration study during the observation of dyadic conversations.

    Science.gov (United States)

    Preisig, Basil C; Eggenberger, Noëmi; Zito, Giuseppe; Vanbellingen, Tim; Schumacher, Rahel; Hopfner, Simone; Nyffeler, Thomas; Gutbrod, Klemens; Annoni, Jean-Marie; Bohlhalter, Stephan; Müri, René M

    2015-03-01

    Co-speech gestures are part of nonverbal communication during conversations. They either support the verbal message or provide the interlocutor with additional information. Furthermore, they prompt as nonverbal cues the cooperative process of turn taking. In the present study, we investigated the influence of co-speech gestures on the perception of dyadic dialogue in aphasic patients. In particular, we analysed the impact of co-speech gestures on gaze direction (towards speaker or listener) and fixation of body parts. We hypothesized that aphasic patients, who are restricted in verbal comprehension, adapt their visual exploration strategies. Sixteen aphasic patients and 23 healthy control subjects participated in the study. Visual exploration behaviour was measured by means of a contact-free infrared eye-tracker while subjects were watching videos depicting spontaneous dialogues between two individuals. Cumulative fixation duration and mean fixation duration were calculated for the factors co-speech gesture (present and absent), gaze direction (to the speaker or to the listener), and region of interest (ROI), including hands, face, and body. Both aphasic patients and healthy controls mainly fixated the speaker's face. We found a significant co-speech gesture × ROI interaction, indicating that the presence of a co-speech gesture encouraged subjects to look at the speaker. Further, there was a significant gaze direction × ROI × group interaction revealing that aphasic patients showed reduced cumulative fixation duration on the speaker's face compared to healthy controls. Co-speech gestures guide the observer's attention towards the speaker, the source of semantic input. It is discussed whether an underlying semantic processing deficit or a deficit to integrate audio-visual information may cause aphasic patients to explore less the speaker's face. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. SU-D-209-06: Study On the Dose Conversion Coefficients in Pediatric Radiography with the Development of Children Voxel Phantoms

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Q [Institute of Radiation Medicine Fudan University, Shanghai (China); Shanghai General Hospital, Shanghai, Shanghai (China); Zhuo, W; Liu, H [Institute of Radiation Medicine Fudan University, Shanghai (China); Liu, Y; Chen, T [Shanghai General Hospital, Shanghai, Shanghai (China)

    2016-06-15

    Purpose: Conversion coefficients of organ dose normalized to entrance skin dose (ESD) are widely used to evaluate the organ doses directly using ESD without time-consuming dose measurement, this work aims to investigate the dose conversion coefficients in pediatric chest and abdomen radiography with the development of 5 years and 10 years old children voxel phantoms. Methods: After segmentation of organs and tissues from CT slice images of ATOM tissue-equivalent phantoms, a 5-year-old and a 10-year-old children computational voxel phantoms were developed for Monte Carlo simulation. The organ doses and the entrance skin dose for pediatric chest postero-anterior projection and abdominal antero-posterior projection were simulated at the same time, and then the organ dose conversion coefficients were calculated.To verify the simulated results, dose measurement was carried out with ATOM tissue-equivalent phantoms for 5 year chest radiography. Results: Simulated results and experimental results matched very well with each other, the result differences of all the organs covered in radiation field were below 16% for 5-year-old child in chest projection. I showed that the conversion coefficients of organs covered in the radiation field were much larger than organs out of the field for all the study cases, for example, the conversion coefficients of stomach, liver intestines, and pancreas are larger for abdomen radiography while conversion coefficients of lungs are larger for chest radiography. Conclusion: The voxel children phantoms were helpful to evaluate the radiation doses more accurately and efficiently. Radiation field was the essential factor that affects the organ dose, use reasonably small field should be encouraged for radiation protection. This work was supported by the National Natural Science Foundation of China(11475047)

  1. Temporal lobe and inferior frontal gyrus dysfunction in patients with schizophrenia during face-to-face conversation: a near-infrared spectroscopy study.

    Science.gov (United States)

    Takei, Yuichi; Suda, Masashi; Aoyama, Yoshiyuki; Yamaguchi, Miho; Sakurai, Noriko; Narita, Kosuke; Fukuda, Masato; Mikuni, Masahiko

    2013-11-01

    Schizophrenia (SC) is marked by poor social-role performance and social-skill deficits that are well reflected in daily conversation. Although the mechanism underlying these impairments has been investigated by functional neuroimaging, technical limitations have prevented the investigation of brain activation during conversation in typical clinical situations. To fill this research gap, this study investigated and compared frontal and temporal lobe activation in patients with SC during face-to-face conversation. Frontal and temporal lobe activation in 29 patients and 31 normal controls (NC) (n = 60) were measured during 180-s conversation periods by using near-infrared spectroscopy (NIRS). The grand average values of oxyhemoglobin concentration ([oxy-Hb]) changes during task performance were analyzed to determine their correlation with clinical variables and Positive and Negative Syndrome Scale (PANSS) subscores. Compared to NCs, patients with SC exhibited decreased performance in the conversation task and decreased activation in both the temporal lobes and the right inferior frontal gyrus (IFG) during task performance, as indicated by the grand average of [oxy-Hb] changes. The decreased activation in the left temporal lobe was negatively correlated with the PANSS disorganization and negative symptoms subscores and that in the right IFG was negatively correlated with illness duration, PANSS disorganization, and negative symptom subscores. These findings indicate that brain dysfunction in SC during conversation is related to functional deficits in both the temporal lobes and the right IFG and manifests primarily in the form of disorganized thinking and negative symptomatology. Copyright © 2013 Elsevier Ltd. All rights reserved.

  2. SU-D-209-06: Study On the Dose Conversion Coefficients in Pediatric Radiography with the Development of Children Voxel Phantoms

    International Nuclear Information System (INIS)

    Liu, Q; Zhuo, W; Liu, H; Liu, Y; Chen, T

    2016-01-01

    Purpose: Conversion coefficients of organ dose normalized to entrance skin dose (ESD) are widely used to evaluate the organ doses directly using ESD without time-consuming dose measurement, this work aims to investigate the dose conversion coefficients in pediatric chest and abdomen radiography with the development of 5 years and 10 years old children voxel phantoms. Methods: After segmentation of organs and tissues from CT slice images of ATOM tissue-equivalent phantoms, a 5-year-old and a 10-year-old children computational voxel phantoms were developed for Monte Carlo simulation. The organ doses and the entrance skin dose for pediatric chest postero-anterior projection and abdominal antero-posterior projection were simulated at the same time, and then the organ dose conversion coefficients were calculated.To verify the simulated results, dose measurement was carried out with ATOM tissue-equivalent phantoms for 5 year chest radiography. Results: Simulated results and experimental results matched very well with each other, the result differences of all the organs covered in radiation field were below 16% for 5-year-old child in chest projection. I showed that the conversion coefficients of organs covered in the radiation field were much larger than organs out of the field for all the study cases, for example, the conversion coefficients of stomach, liver intestines, and pancreas are larger for abdomen radiography while conversion coefficients of lungs are larger for chest radiography. Conclusion: The voxel children phantoms were helpful to evaluate the radiation doses more accurately and efficiently. Radiation field was the essential factor that affects the organ dose, use reasonably small field should be encouraged for radiation protection. This work was supported by the National Natural Science Foundation of China(11475047)

  3. Combustion of solid alternative fuels in the cement kiln burner

    DEFF Research Database (Denmark)

    Nørskov, Linda Kaare

    In the cement industry there is an increasing environmental and financial motivation for substituting conventional fossil fuels with alternative fuels, being biomass or waste derived fuels. However, the introduction of alternative fuels may influence emissions, cement product quality, process...... stability, and process efficiency. Alternative fuel substitution in the calciner unit has reached close to 100% at many cement plants and to further increase the use of alternative fuels rotary kiln substitution must be enhanced. At present, limited systematic knowledge of the alternative fuel combustion...... properties and the influence on the flame formation is available. In this project a scientific approach to increase the fundamental understanding of alternative fuel conversion in the rotary kiln burner is employed through literature studies, experimental combustion characterisation studies, combustion...

  4. Cheese is a reliable alternative meal for solid-phase gastric emptying study.

    Science.gov (United States)

    Drubach, Laura A; Kourmouzi, Vasiliki; Fahey, Frederic H

    2010-05-01

    We evaluated the labeling stability of several alternative meals that could be used to perform solid-phase gastric emptying study. Cooked egg whites labeled with technetium-99m sulfur colloid served as a control. Packaged instant oatmeal and instant mashed potatoes were prepared by adding hot water. Cheddar cheese was melted. Peanut butter was added to bread. The different meals were mixed with technetium-99m sulfur colloid (2.2-3.7 MBq), chopped into small pieces and placed in a glass tube containing gastric juice. Four samples of each meal were analyzed after 1 and 4 h of agitation with a 3-D rotator (two samples per time point). The meal samples were washed with 2 ml of saline and filtered using a blood transfusion filter. The activity in each sample before and after filtering was assayed in a dose calibrator. The percentage of initial radioactivity remaining with the meal of admixture with gastric juice was measured and the average of the two samples was taken. The percentage of activity bound to the solid phase was 98.2+/-1.9, 95.6+/-1.1, 62.1+/-1.7, 41.8+/-0.6, and 74.5+/-3.8% at 1 h and 98.5+/-1.0, 95.8+/-2.6, 77.2+/-6.8, 55.5+/-3.4 and 40.2+/-22.1 at 4 h for egg whites, cheese, oatmeal, mashed potatoes and peanut butter respectively. For egg whites and cheese, there was no significant difference between the values at 1 and 4 h (P>0.8). Cheddar cheese provides an alternative meal for assessing solid gastric emptying in children comparable to egg whites. Oatmeal and mashed potatoes had low and variable labeling stability and are not recommended. In view of the significant proportion of pediatric patients who refuse to eat scrambled eggs or have allergy to eggs, the availability of other meal choices is essential. The versatility of cheddar cheese, which can be added to macaroni or as a topping on pizza, makes it a useful alternative to labeled eggs.

  5. Provider and patient perspectives on opioids and alternative treatments for managing chronic pain: a qualitative study.

    Science.gov (United States)

    Penney, Lauren S; Ritenbaugh, Cheryl; DeBar, Lynn L; Elder, Charles; Deyo, Richard A

    2017-03-24

    Current literature describes the limits and pitfalls of using opioid pharmacotherapy for chronic pain and the importance of identifying alternatives. The objective of this study was to identify the practical issues patients and providers face when accessing alternatives to opioids, and how multiple parties view these issues. Qualitative data were gathered to evaluate the outcomes of acupuncture and chiropractic (A/C) services for chronic musculoskeletal pain (CMP) using structured interview guides among patients with CMP (n = 90) and primary care providers (PCPs) (n = 25) purposively sampled from a managed care health care system as well as from contracted community A/C providers (n = 14). Focus groups and interviews were conducted patients with CMP with varying histories of A/C use. Plan PCPs and contracted A/C providers took part in individual interviews. All participants were asked about their experiences managing chronic pain and experience with and/or attitudes about A/C treatment. Audio recordings were transcribed and thematically coded. A summarized version of the focus group/interview guides is included in the Additional file 1. We identified four themes around opioid use: (1) attitudes toward use of opioids to manage chronic pain; (2) the limited alternative options for chronic pain management; (3) the potential of A/C care as a tool to help manage pain; and (4) the complex system around chronic pain management. Despite widespread dissatisfaction with opioid medications for pain management, many practical barriers challenged access to other options. Most of the participants' perceived A/C care as helpful for short term pain relief. We identified that problems with timing, expectations, and plan coverage limited A/C care potential for pain relief treatment. These results suggest that education about realistic expectations for chronic pain management and therapy options, as well as making A/C care more easily accessible, might lead to more

  6. Smokers' unprompted comments on cigarette additives during conversations about the genetic basis for nicotine addiction: a focus group study.

    Science.gov (United States)

    Philpott, Sydney E; Gehlert, Sarah; Waters, Erika A

    2018-04-13

    Research designed to elicit smokers' cognitive and affective reactions to information about chemicals that tobacco companies add to cigarettes ("additives") found that knowledge is limited. However, little is known about smokers' unprompted thoughts and feelings about additives. Such information could be used to shape future communication efforts. We explored the content and possible functions of spontaneous statements about cigarette additives made by smokers during a study examining reactions to learning about the genetic link to nicotine addiction. Adult smokers (N = 84) were recruited from a medium-sized Midwestern city. Focus groups (N = 13) were conducted between April-September 2012. Data were analyzed by 2 coders using thematic analysis. Comments about cigarette additives arose without prompting by the focus group moderator. Three main themes were identified: (1) discussing additives helped participants navigate the conceptual link between smoking and genetics, (2) additives were discussed as an alternative mechanism for addiction to cigarettes, and (3) additives provided an alternative mechanism by which cigarette smoking exacerbates physical harm. Notably, discussion of additives contained a pervasive tone of mistrust illustrated by words like "they" and "them," by statements of uncertainty such as "you don't know what they're putting into cigarettes," and by negative affective verbalizations such as "nasty" and "disgusting". Participants had distinct beliefs about cigarette additives, each of which seemed to serve a purpose. Although mistrust may complicate communication about the health risks of tobacco use, health communication experts could use smokers' existing beliefs and feelings to better design more effective anti-smoking messages.

  7. Preventing long-lasting fear recovery using bilateral alternating sensory stimulation: A translational study.

    Science.gov (United States)

    Wurtz, H; El-Khoury-Malhame, M; Wilhelm, F H; Michael, T; Beetz, E M; Roques, J; Reynaud, E; Courtin, J; Khalfa, S; Herry, C

    2016-05-03

    Posttraumatic stress disorder (PTSD) is a highly debilitating and prevalent psychological disorder. It is characterized by highly distressing intrusive trauma memories that are partly explained by fear conditioning. Despite efficient therapeutic approaches, a subset of PTSD patients displays spontaneous recurrence of traumatic memories after successful treatment. The development of animal behavioral models mimicking the individual variability in treatment outcome for PTSD patients represent therefore an important challenge as it allows for the identification of predicting factors of resilience or susceptibility to relapse. However, to date, only few animal behavioral models of long-lasting fear recovery have been developed and their predictive validity has not been tested directly. The objectives of this study were twofold. First we aimed to develop a simple animal behavioral model of long-lasting fear recovery based on auditory cued fear conditioning and extinction learning, which recapitulates the heterogeneity of fear responses observed in PTSD patients after successful treatment. Second we aimed at testing the predictive validity of our behavioral model and used to this purpose a translational approach based (i) on the demonstration of the efficiency of Eye Movement Desensitization and Reprocessing (EMDR) therapy to reduce conditioned fear responses in PTSD patients and (ii) on the implementation in our behavioral model of an electrical bilateral alternating stimulation of the eyelid which mimics the core feature of EMDR. Our data indicate that electrical bilateral alternating stimulation of the eyelid during extinction learning alleviates long-lasting fear recovery of conditioned fear responses and dramatically reduces inter-individual variability. These results demonstrate the face and predictive validity of our animal behavioral model and provide an interesting tool to understand the neurobiological underpinnings of long-lasting fear recovery. Copyright

  8. Barnwell Nuclear Fuels Plant applicability study. Volume II. BNFP: utilization alternatives, evaluations, and conclusions

    International Nuclear Information System (INIS)

    1978-04-01

    Descriptions and status of the Barnwell separations facility and related fuel cycle facilities are given. Alternative uses other than reprocessing, evaluation of uses for reprocessing alternatives, resource utilization and its relationship to U.S. security objectives, and evaluation of ownership-management options are discussed

  9. Microbial Energy Conversion

    Energy Technology Data Exchange (ETDEWEB)

    Buckley, Merry [American Society for Microbiology (ASM), Washington, DC (United States); Wall, Judy D. [Univ. of Missouri, Columbia, MO (United States)

    2006-10-01

    The American Academy of Microbiology convened a colloquium March 10-12, 2006, in San Francisco, California, to discuss the production of energy fuels by microbial conversions. The status of research into various microbial energy technologies, the advantages and disadvantages of each of these approaches, research needs in the field, and education and training issues were examined, with the goal of identifying routes for producing biofuels that would both decrease the need for fossil fuels and reduce greenhouse gas emissions. Currently, the choices for providing energy are limited. Policy makers and the research community must begin to pursue a broader array of potential energy technologies. A diverse energy portfolio that includes an assortment of microbial energy choices will allow communities and consumers to select the best energy solution for their own particular needs. Funding agencies and governments alike need to prepare for future energy needs by investing both in the microbial energy technologies that work today and in the untested technologies that will serve the world’s needs tomorrow. More mature bioprocesses, such as ethanol production from starchy materials and methane from waste digestors, will find applications in the short term. However, innovative techniques for liquid fuel or biohydrogen production are among the longer term possibilities that should also be vigorously explored, starting now. Microorganisms can help meet human energy needs in any of a number of ways. In their most obvious role in energy conversion, microorganisms can generate fuels, including ethanol, hydrogen, methane, lipids, and butanol, which can be burned to produce energy. Alternatively, bacteria can be put to use in microbial fuel cells, where they carry out the direct conversion of biomass into electricity. Microorganisms may also be used some day to make oil and natural gas technologies more efficient by sequestering carbon or by assisting in the recovery of oil and

  10. Advanced transportation system studies, technical area 3. Alternate propulsion subsystem concepts: J-2S restart study

    Science.gov (United States)

    Vilja, John; Levack, Daniel

    1993-04-01

    The objectives were to assess what design changes would be required to remit late production of the J-2S engine for use as a large high energy upper stage engine. The study assessed design changes required to perform per the J-2S model specification, manufacturing changes required due to obsolescence or improvements in state-of-the-practice, availability issues for supplier provided items, and provided cost and schedule estimates for this configuration. The confidence that J-2S production could be reinitiated within reasonable costs and schedules was provided. No significant technical issues were identified in either the producibility study or in the review of previous technical data. Areas of potential cost reduction were identified which could be quantified to a greater extent with further manufacturing planning. The proposed schedule can be met with no foreseeable impacts. The results of the study provided the necessary foundation for the detailed manufacturing and test plans and non-recurring and recurring cost estimates that are needed to complete the effort to reinitiate production of the J-2S engine system.

  11. Three-generation study of neutrino spin-flavor conversion in supernovae and implication for the neutrino magnetic moment

    Science.gov (United States)

    Ando, Shin'ichiro; Sato, Katsuhiko

    2003-01-01

    We investigate resonant spin-flavor (RSF) conversions of supernova neutrinos which are induced by the interaction of neutrino magnetic moment and supernova magnetic fields. From the formulation which includes all three-flavor neutrinos and antineutrinos, we give a new crossing diagram that includes not only ordinary Mikheyev-Smirnov-Wolfenstein (MSW) resonance but also a magnetically induced RSF effect. With the diagram, it is found that four conversions occur in supernovae: two are induced by the RSF effect and two by the pure MSW effect. We also numerically calculate neutrino conversions in supernova matter, using neutrino mixing parameters inferred from recent experimental results and a realistic supernova progenitor model. The results indicate that until 0.5 sec after the core bounce, the RSF-induced ν¯e↔ντ transition occurs efficiently (adiabatic resonance), when μν≳10- 12μB(B0/5×109 G)-1, where B0 is the strength of the magnetic field at the surface of iron core. We also evaluate the energy spectrum as a function of μνB0 at the super-Kamiokande detector and the Sudbury Neutrino Observatory using the calculated conversion probabilities, and find that the spectral deformation might have the possibility to provide useful information on the neutrino magnetic moment as well as the magnetic field strength in supernovae.

  12. Theoretical and experimental studies on combustion of alternative fuels in cement kilns

    International Nuclear Information System (INIS)

    Axelsen, Ernst Petter

    2002-01-01

    In this thesis, the utilization of alternative fuels for NOx reduction by means of reburning and advanced reburning is considered. Laboratory experiments, full-scale experiments and computational fluid dynamic (CFD) simulations are the basis of the thesis. The goal of the work was to characterize alternative fuels used in cement kilns, with focus on the processes taking place in the precalciner of the cement kiln. To facilitate testing under controlled process conditions, a lab-scale circulating fluidized bed combustion (CFBC) reactor was designed and constructed. A co prehensive study on the fluidization regime in CFBC reactors and precalciners was required to ensure and verify that the operational regime in the CFBC reactor was similar to the regime in a precalciner. Different alternative fuels, such as refuse derived fuel, animal meal and solid hazardous waste, were tested in the CFBC reactor, which proved well suited for characterization of alternative fuels and investigations of NOx reduction, even though the operation of a CFBC reactor is quite complex and gives a certain variation in stability. Experiments with and without circulating mass in the CFBC reactor demonstrated the importance of executing the laboratory combustion experiments in an environment similar to that in the full-scale process, i.e. in the precalciner. Animal meal is believed to follow the reduction route of selective non-catalytic r duction or advanced reburning and to have a special capability of reducing NOx during increased NOx concentrations at the reactor inlet. The increased CO emissions during advanced reburning and reburning with animal meal are most likely to be due to the competition for the OH radical during oxidation of CO and of NH 3 . Furthermore, it was shown, for all fuels, that an increased concentration of NOx at the reactor inlet increases the ratio of NOx at the exit and NOx supplied. Full-scale experiments were executed at Norcem's kiln 6 in Brevik, using solid

  13. Theoretical and experimental studies on combustion of alternative fuels in cement kilns

    Energy Technology Data Exchange (ETDEWEB)

    Axelsen, Ernst Petter

    2002-07-01

    In this thesis, the utilization of alternative fuels for NOx reduction by means of reburning and advanced reburning is considered. Laboratory experiments, full-scale experiments and computational fluid dynamic (CFD) simulations are the basis of the thesis. The goal of the work was to characterize alternative fuels used in cement kilns, with focus on the processes taking place in the precalciner of the cement kiln. To facilitate testing under controlled process conditions, a lab-scale circulating fluidized bed combustion (CFBC) reactor was designed and constructed. A co prehensive study on the fluidization regime in CFBC reactors and precalciners was required to ensure and verify that the operational regime in the CFBC reactor was similar to the regime in a precalciner. Different alternative fuels, such as refuse derived fuel, animal meal and solid hazardous waste, were tested in the CFBC reactor, which proved well suited for characterization of alternative fuels and investigations of NOx reduction, even though the operation of a CFBC reactor is quite complex and gives a certain variation in stability. Experiments with and without circulating mass in the CFBC reactor demonstrated the importance of executing the laboratory combustion experiments in an environment similar to that in the full-scale process, i.e. in the precalciner. Animal meal is believed to follow the reduction route of selective non-catalytic r duction or advanced reburning and to have a special capability of reducing NOx during increased NOx concentrations at the reactor inlet. The increased CO emissions during advanced reburning and reburning with animal meal are most likely to be due to the competition for the OH radical during oxidation of CO and of NH{sub 3}. Furthermore, it was shown, for all fuels, that an increased concentration of NOx at the reactor inlet increases the ratio of NOx at the exit and NOx supplied. Full-scale experiments were executed at Norcem's kiln 6 in Brevik, using solid

  14. Theoretical and experimental studies on combustion of alternative fuels in cement kilns

    Energy Technology Data Exchange (ETDEWEB)

    Axelsen, Ernst Petter

    2002-07-01

    In this thesis, the utilization of alternative fuels for NOx reduction by means of reburning and advanced reburning is considered. Laboratory experiments, full-scale experiments and computational fluid dynamic (CFD) simulations are the basis of the thesis. The goal of the work was to characterize alternative fuels used in cement kilns, with focus on the processes taking place in the precalciner of the cement kiln. To facilitate testing under controlled process conditions, a lab-scale circulating fluidized bed combustion (CFBC) reactor was designed and constructed. A co prehensive study on the fluidization regime in CFBC reactors and precalciners was required to ensure and verify that the operational regime in the CFBC reactor was similar to the regime in a precalciner. Different alternative fuels, such as refuse derived fuel, animal meal and solid hazardous waste, were tested in the CFBC reactor, which proved well suited for characterization of alternative fuels and investigations of NOx reduction, even though the operation of a CFBC reactor is quite complex and gives a certain variation in stability. Experiments with and without circulating mass in the CFBC reactor demonstrated the importance of executing the laboratory combustion experiments in an environment similar to that in the full-scale process, i.e. in the precalciner. Animal meal is believed to follow the reduction route of selective non-catalytic r duction or advanced reburning and to have a special capability of reducing NOx during increased NOx concentrations at the reactor inlet. The increased CO emissions during advanced reburning and reburning with animal meal are most likely to be due to the competition for the OH radical during oxidation of CO and of NH{sub 3}. Furthermore, it was shown, for all fuels, that an increased concentration of NOx at the reactor inlet increases the ratio of NOx at the exit and NOx supplied. Full-scale experiments were executed at Norcem's kiln 6 in Brevik, using

  15. PEEK-OPTIMA? as an alternative to cobalt chrome in the femoral component of total knee replacement: A preliminary study

    OpenAIRE

    Cowie, Raelene M; Briscoe, Adam; Fisher, John; Jennings, Louise M

    2016-01-01

    PEEK-OPTIMA™ (Invibio Ltd, UK) has been considered as an alternative joint arthroplasty bearing material due to its favourable mechanical properties and the biocompatibility of its wear debris. In this study, the potential to use injection moulded PEEK-OPTIMA™ as an alternative to cobalt chrome in the femoral component of a total knee replacement was investigated in terms of its wear performance. Experimental wear simulation of three cobalt chrome and three PEEK-OPTIMA™ femoral components art...

  16. [Before you diagnose a patient with a conversion disorder, perform a thorough general medical and neurological examination. Case study].

    Science.gov (United States)

    Pawełczyk, Tomasz; Pawełczyk, Agnieszka; Rabe-Jabłońska, Jolanta

    2012-01-01

    Dissociative and conversion disorders are classified together according to ICD-10 as states that are not confirmed by the presence of somatic diseases, which they suggest. According to the DSM-IV, both disorders are classified separately. Conversion disorders are a group of psychiatric disorders whose symptoms mimic the presence of malfunction or loss of motor or sensory function, whereas the nature and dynamics of the observed symptoms is not fully explained by the results of objective assessments and consultations, nor is the direct effect of a psychoactive substance. Impaired mental integration of different functions which normally interact simultaneously in the perception of reality and inner experience of the individual is found in dissociative disorders. The article describes the case of 25-year old man, in whom after initial suspicion of myasthenia gravis and its exclusion, a diagnosis of conversion disorder was made on the basis of the clinical picture and treatment with an SSRI antidepressant and individual psychotherapy were recommended. No improvement in mental and neurological status after six month therapy resulted in an in-depth diagnostics in a clinical setting and diagnosis of brain stem tumor (aastrocytoma fibrillare). (a) Neuroimaging is a source of important clinical data and in many cases should constitute an inherent element of a psychiatric diagnosis. (b) Diagnosis of conversion (dissociative) disorders requires a precise differential diagnosis, excluding the somatic causes of observed neurological ailments. (c) A late diagnosis of neurological or somatic causes of symptoms which arouse a suspicion of conversion (dissociative) disorders may make a radical treatment impossible or may considerably aggravate the remote prognosis and quality of the patients' life.

  17. Passenger and Cell Phone Conversations in Simulated Driving

    Science.gov (United States)

    Drews, Frank A.; Pasupathi, Monisha; Strayer, David L.

    2008-01-01

    This study examines how conversing with passengers in a vehicle differs from conversing on a cell phone while driving. We compared how well drivers were able to deal with the demands of driving when conversing on a cell phone, conversing with a passenger, and when driving without any distraction. In the conversation conditions, participants were…

  18. Alternative Exercise Technologies to Fight against Sarcopenia at Old Age: A Series of Studies and Review

    Directory of Open Access Journals (Sweden)

    Wolfgang Kemmler

    2012-01-01

    Full Text Available The most effective physiologic mean to prevent sarcopenia and related muscle malfunction is a physically active lifestyle, or even better, physical exercise. However, due to time constraints, lack of motivation, or physical limitations, a large number of elderly subjects are either unwilling or unable to perform conventional workouts. In this context, two new exercise technologies, whole-body vibration (WBV and whole-body electromyostimulation (WB-EMS, may exhibit a save, autonomous, and efficient alternative to increase or maintain muscle mass and function. Regarding WB-EMS, the few recent studies indeed demonstrated highly relevant effects of this technology on muscle mass, strength, and power parameters at least in the elderly, with equal or even higher effects compared with conventional resistance exercise. On the contrary, although the majority of studies with elderly subjects confirmed the positive effect of WBV on strength and power parameters, a corresponding relevant effect on muscle mass was not reported. However, well-designed studies with adequate statistical power should focus more intensely on this issue.

  19. Tenebrio molitor (Coleoptera: Tenebrionidae) as an alternative host to study fungal infections.

    Science.gov (United States)

    de Souza, Patrícia Canteri; Morey, Alexandre Tadachi; Castanheira, Gabriel Marcondes; Bocate, Karla Paiva; Panagio, Luciano Aparecido; Ito, Fabio Augusto; Furlaneto, Márcia Cristina; Yamada-Ogatta, Sueli Fumie; Costa, Idessânia Nazareth; Mora-Montes, Hector Manuel; Almeida, Ricardo Sergio

    2015-11-01

    Models of host–pathogen interactions are crucial for the analysis of microbial pathogenesis. In this context, invertebrate hosts, including Drosophila melanogaster (fruit fly), Caenorhabditis elegans (nematode) and Galleria mellonella (moth), have been used to study the pathogenesis of fungi and bacteria. Each of these organisms offers distinct benefits in elucidating host–pathogen interactions. In this study,we present a newinvertebrate infection model to study fungal infections: the Tenebrio molitor (beetle) larvae. Here we performed T. molitor larvae infection with one of two important fungal human pathogens, Candida albicans or Cryptococcus neoformans, and analyzed survival curves and larva infected tissues.We showed that increasing concentrations of inoculum of both fungi resulted in increased mortality rates, demonstrating the efficiency of the method to evaluate the virulence of pathogenic yeasts. Additionally, following 12 h post-infection, C. albicans formsmycelia, spreading its hyphae through the larva tissue,whilst GMS stain enabled the visualization of C. neoformans yeast and theirmelanin capsule. These larvae are easier to cultivate in the laboratory than G. mellonella larvae, and offer the same benefits. Therefore, this insect model could be a useful alternative tool to screen clinical pathogenic yeast strainswith distinct virulence traits or different mutant strains.

  20. A STUDY ON LIMITATION OF GOVERNMENT INITIATIVE MODEL FOR ALTERNATIVE FUEL VEHICLE (AFV PROMOTION IN CHINA

    Directory of Open Access Journals (Sweden)

    Byunghun Choi

    2016-04-01

    Full Text Available Chinese responsibility for reducing Greenhouse Gas or carbon dioxide emission increases continuously. Chinese government suggested two targets; Alternative Fuel Vehicle output volume 500 thousand and AFV market share 5% by the end of 2011. However any of two targets did not come true. Therefore this study accessed the question, ‘why Chinese government initiative model for AFV promotion has been so poor?’ This study reviewed the transition process for AFV policies in China and made a structural analysis for three key policies since 2009. As a result the number of articles for related industries or factor endowments was relatively more than firm strategy or demand conditions. Also this study accessed the AFV strategy of Six SOEs from the perspective of social responsibility. Six SOEs have more concentrated on electric vehicle rather than hybrid vehicle with following the government leadership. However major EV or HEV models of them mostly were made by Joint Ventures being under control of foreign makers and the JVs have actually controlled over AFV business. So the limitation of Chinese government initiative model resulted from supplier-centric approach with targeting for public transportation and institution consumer, and it caused a failure to create the demand conditions of general customers.