Challenges of the refining and bio-refining integration: a future view; O desafio da integracao refino-bio-refino: uma visao do futuro

Energy Technology Data Exchange (ETDEWEB)

Baptista, Claudia Alvarenga; Oliveira, Sandra Lima de [PETROBRAS S. A., Rio de de Janeiro, RJ (Brazil); Silva, Suely Coutinho da [Hope Consultoria Ltda., Rio de Janeiro, RJ (Brazil)

2008-07-01

As the world economy growths, it is expected an increase in the fuels demand. In the other hand, there is a public denounce against the harmful of gas emissions from the mineral fuels, especial the emission of greenhouse gases. Based on this scenario, there is a growing search for renewable fuels as an alternative for the present world energetic matrix. Therefore the biofuel has conquered more and more participation in the economy as a clean grow-your-own fuel. It is not only a renewable fuel but also a way to reduces Co2 emission. The use of this kind of fuel can bring environmental, social and economic advantages. So, a feasible proposal for the near future could be the performance of a binomial and dynamic model that takes place in the integration between biorefining and conventional refining. Biorefining is similar in concept to the petroleum refining industry, except that renewable biomass materials or vegetable oil are the feedstocks rather than crude oil. An important incentive to the integration of these two concepts is the alternative to process the majority of the conventional refining residue or by products in the biorefining. It is possible to produce high quality low emission fuel from co-conversion of biomass and petroleum residue. There are important processes that can be used to carry out this object, such as gasification coupled with Fischer-Tropsch. Besides the production of PREMIUM quality fuel, the energy and the hydrogen obtained in the gasification process can be used in the conventional refining. Biomass can also be turned into alcohol fuel by enzymatic hydrolysis and can be mixed in the refinery gasoline pool for emissions reduction. Another possibility is to process vegetable oil together with middle distillate in the conventional hydrotreating unity. Although the optimized integration involves technical and economic challenges, it is known that this is an important opportunity to mitigate the environmental problems and to allow the world

Grain size refinement of inconel 718 thermomechanical processing

International Nuclear Information System (INIS)

Okimoto, P.C.

1988-01-01

Inconel 718 is a Ni-Fe precipitation treated superalloy. It presents good thermal fatigue properties when the material has small grain size. The aim of this work is to study the grain size refinement by thermomechanical processing, through observations of the microstructural evolution and the influence of some of the process variables in the final grain size. The results have shown that this refinement occured by static recrystallization. The presence of precipitates have influenced the final grain size if the deformations are below 60%. For greater deformations the grain size is independent of the precipitate distribution in the matrix and tends to a limit size of 5 μm. (author)

A new concept for product refining in the Purex process

International Nuclear Information System (INIS)

Henrich, E.; Bauder, U.; Marquardt, R.

1986-01-01

In actual Purex plants the products are refined in additional solvent extraction cycles. Crystallization of uranyl and plutonyl nitrate from aqueous nitric acid solution is proposed as a potentially simpler product refining concept. Suitable crystallization conditions are being investigated in the laboratory using simulated and actual process solutions. A thorough removal of mother liquor is an essential purification step and well washed crystals usually contain less than 1% of an individual impurity. Crystallization simultaneously comprises a product concentration step. Hexavalent uranium can be separated from lower-valent plutonium. An outline of an integrated processing concept is given. Product refining by crystallization is compact; recycling of mother liquor plus wash acid prevents product loss and the generation of additional waste streams. (orig.) [de

Refining of biodiesel by ceramic membrane separation

Energy Technology Data Exchange (ETDEWEB)

Wang, Yong; Ou, Shiyi; Tan, Yanlai; Tang, Shuze [Department of Food Science and Engineering, Jinan University, Guangzhou 510632 (China); Wang, Xingguo; Liu, Yuanfa [School of Food Science and Technology, Jiangnan University, Wuxi 214112 (China)

2009-03-15

A ceramic membrane separation process for biodiesel refining was developed to reduce the considerable usage of water needed in the conventional water washing process. Crude biodiesel produced by refined palm oil was micro-filtered by ceramic membranes of the pore size of 0.6, 0.2 and 0.1 {mu}m to remove the residual soap and free glycerol, at the transmembrane pressure of 0.15 MPa and temperature of 60 C. The flux through membrane maintained at 300 L m{sup -} {sup 2} h{sup -} {sup 1} when the volumetric concentrated ratio reached 4. The content of potassium, sodium, calcium and magnesium in the whole permeate was 1.40, 1.78, 0.81 and 0.20 mg/kg respectively, as determined by inductively coupled plasma-atomic emission spectroscopy. These values are lower than the EN 14538 specifications. The residual free glycerol in the permeate was estimated by water extraction, its value was 0.0108 wt.%. This ceramic membrane technology was a potential environmental process for the refining of biodiesel. (author)

Processes subject to integrated pollution control. Petroleum processes: oil refining and associated processes

International Nuclear Information System (INIS)

1995-01-01

This document, part of a series offering guidance on pollution control regulations issued by Her Majesty's Inspectorate of Pollution, (HMIP) focuses on petroleum processes such as oil refining and other associated processes. The various industrial processes used, their associated pollution release routes into the environment and techniques for controlling these releases are all discussed. Environmental quality standards are related to national and international agreements on pollution control and abatement. HMIP's work on air, water and land pollution monitoring is also reported. (UK)

Refining Nodes and Edges of State Machines

DEFF Research Database (Denmark)

Hallerstede, Stefan; Snook, Colin

2011-01-01

State machines are hierarchical automata that are widely used to structure complex behavioural specifications. We develop two notions of refinement of state machines, node refinement and edge refinement. We compare the two notions by means of examples and argue that, by adopting simple conventions...... refinement theory and UML-B state machine refinement influences the style of node refinement. Hence we propose a method with direct proof of state machine refinement avoiding the detour via Event-B that is needed by UML-B....

Limit of grain refinement during ECAP process. Temperature influence

International Nuclear Information System (INIS)

Chuvil'deev, V.N.; Kopylov, V.I.; Nokhrin, A.V.; Makarov, I.M.; Lopatin, Yu.G.

2004-01-01

Experimental and theoretical study results are reported for the process of deformation grain refinement under severe plastic deformation. A generalization is made for experimental study results on deformation dispersing of unalloyed metals and aluminium and magnesium base alloys. The model is built that allows calculating the value of minimum grain size attained by the method of equal-channel angular pressing. The expressions are derived which describe the dependence of grain refinement limit on the nature of material and the temperature of severe plastic deformation [ru

Process technology for refining crude soybean oil – a product from ...

African Journals Online (AJOL)

Process technology for refining crude soybean oil – a product from soycake meal production in Ghana. ... yield of 83.3 per cent was recorded. Results of quality assessment of the final laboratory refined oil compared favourably with Ghana Standards Board's specification for edible soybean oil. Ghana Journal of Science Vol.

Zeolites as Catalysts for Fuels Refining after Indirect Liquefaction Processes

Directory of Open Access Journals (Sweden)

Arno de Klerk

2018-01-01

Full Text Available The use of zeolite catalysts for the refining of products from methanol synthesis and Fisher–Tropsch synthesis was reviewed. The focus was on fuels refining processes and differences in the application to indirect liquefaction products was compared to petroleum, which is often a case of managing different molecules. Processes covered were skeletal isomerisation of n-butenes, hydroisomerisation of n-butane, aliphatic alkylation, alkene oligomerisation, methanol to hydrocarbons, ethanol and heavier alcohols to hydrocarbons, carbonyls to hydrocarbons, etherification of alkenes with alcohols, light naphtha hydroisomerisation, catalytic naphtha reforming, hydroisomerisation of distillate, hydrocracking and fluid catalytic cracking. The zeolite types that are already industrially used were pointed out, as well as zeolite types that have future promise for specific conversion processes.

On macromolecular refinement at subatomic resolution with interatomic scatterers

Energy Technology Data Exchange (ETDEWEB)

Afonine, Pavel V., E-mail: pafonine@lbl.gov; Grosse-Kunstleve, Ralf W.; Adams, Paul D. [Lawrence Berkeley National Laboratory, One Cyclotron Road, BLDG 64R0121, Berkeley, CA 94720 (United States); Lunin, Vladimir Y. [Institute of Mathematical Problems of Biology, Russian Academy of Sciences, Pushchino 142290 (Russian Federation); Urzhumtsev, Alexandre [IGMBC, 1 Rue L. Fries, 67404 Illkirch and IBMC, 15 Rue R. Descartes, 67084 Strasbourg (France); Faculty of Sciences, Nancy University, 54506 Vandoeuvre-lès-Nancy (France); Lawrence Berkeley National Laboratory, One Cyclotron Road, BLDG 64R0121, Berkeley, CA 94720 (United States)

2007-11-01

Modelling deformation electron density using interatomic scatters is simpler than multipolar methods, produces comparable results at subatomic resolution and can easily be applied to macromolecules. A study of the accurate electron-density distribution in molecular crystals at subatomic resolution (better than ∼1.0 Å) requires more detailed models than those based on independent spherical atoms. A tool that is conventionally used in small-molecule crystallography is the multipolar model. Even at upper resolution limits of 0.8–1.0 Å, the number of experimental data is insufficient for full multipolar model refinement. As an alternative, a simpler model composed of conventional independent spherical atoms augmented by additional scatterers to model bonding effects has been proposed. Refinement of these mixed models for several benchmark data sets gave results that were comparable in quality with the results of multipolar refinement and superior to those for conventional models. Applications to several data sets of both small molecules and macromolecules are shown. These refinements were performed using the general-purpose macromolecular refinement module phenix.refine of the PHENIX package.

User-centric Query Refinement and Processing Using Granularity Based Strategies

NARCIS (Netherlands)

Zeng, Y.; Zhong, N.; Wang, Y.; Qin, Y.; Huang, Z.; Zhou, H; Yao, Y; van Harmelen, F.A.H.

2011-01-01

Under the context of large-scale scientific literatures, this paper provides a user-centric approach for refining and processing incomplete or vague query based on cognitive- and granularity-based strategies. From the viewpoints of user interests retention and granular information processing, we

Processing (refining) of petroleum and natural gases. Pererabotka neftyanykh i prirodnykh gazov

Energy Technology Data Exchange (ETDEWEB)

Berlin, M A; Gorechenkov, V G; Volkov, N P

1981-01-01

A discussion is made of the theoretical principles underlying the processes involved in the processing of natural and petroleum gases and gas condensate. Information is given on apparatus, engineering systems, and machine methods for the designing of gas refining plants. The book is intended for engineers and operation personnel of gas refining plants, and might also be useful to senior undergraduates at chemistry and petroleum institutes of higher learning. 278 references, 54 tables.

High-speed double-disc TMP [thermomechanical pulp] from northern and southern softwoods: One or two refining stages

Energy Technology Data Exchange (ETDEWEB)

Sabourin, M.J. (Andritz Sprout-Bauer, Inc., Springfield, OH (United States)); Cort, J.B.; Musselman, R.L. (Andritz Sprout-Bauer, Inc., Muncy, PA (United States))

1994-01-01

Pilot-plant studies were carried out to evaluate one- and two-stage high-speed refining processes for production of thermomechanical pulp (TMP) at minimal energy consumption. Both northern (black spruce/balsam fir) and southern (lobolly pine) wood species were tested. Preliminary results indicate both one- and two-stage high-speed refining are suitable for the production of TMP from spruce and fir. Single-stage, high-speed refining of spruce/fir resulted in over 25% energy savings compared to conventional TMP production. The resulting TMP had improved optical and shive content properties, with slightly reduced pulp strength and long fiber content. Two stages of refining were necessary to optimize pulp quality from the lobolly pine furnish. A 15% energy reduction was obtained when comparing high-speed and conventional TMP pulping of lobolly pine at similar operating conditions. The high-speed pine TMP had comparable bonding strength, shive content, and lower tear than conventional two-stage lobolly pine TMP. 14 refs., 11 figs., 6 tabs.

Efficiency of the refining processes in removing 14C-dichlorvos residues in soybean oil

International Nuclear Information System (INIS)

Soliman, S.M.

2006-01-01

Crude soybean oil extracted from grains treated with 14 C-dichlorvos at a dose 24 mg insecticide / kg seeds and stored for 30 weeks was subjected to different refining processes such as alkali treatment, bleaching, winterization and deodorization. The effect of the refining processes on the nature and magnitude of the originally present residues was investigated. The insecticide residues in crude oil and cake amounted to 9.5% and 55% , respectively, of original residues inside the seeds. Extraction of the seeds with hexane gave crude oil with 9.5 % of original residues in seeds. The l4 C-activity in the crude stored Soya beans oil could be reduced by about 82% of radioactivity originally present in crude oil eliminated by simulated commercial processes locally used for oil refining. A high percentage of the residues (50-55%) were eliminated during alkali treatment and bleaching. Refining of soybeans oil fortified with '1 4 C-dichlorovos. The final refined oil had only 13% of the radioactivity originally present, mainly in the form of dichlorvos, dimethyl and monomethyl phosphate in addition to desmethyl dichlorvos in oil with aged residues

Combinative application of pH-zone-refining and conventional high-speed counter-current chromatography for preparative separation of caged polyprenylated xanthones from gamboge.

Science.gov (United States)

Xu, Min; Fu, Wenwei; Zhang, Baojun; Tan, Hongsheng; Xiu, Yanfeng; Xu, Hongxi

2016-02-01

An efficient method for the preparative separation of four structurally similar caged xanthones from the crude extracts of gamboge was established, which involves the combination of pH-zone-refining counter-current chromatography and conventional high-speed counter-current chromatography for the first time. pH-zone-refining counter-current chromatography was performed with the solvent system composed of n-hexane/ethyl acetate/methanol/water (7:3:8:2, v/v/v/v), where 0.1% trifluoroacetic acid was added to the upper organic stationary phase as a retainer and 0.03% triethylamine was added to the aqueous mobile phase as an eluter. From 3.157 g of the crude extract, 1.134 g of gambogic acid, 180.5 mg of gambogenic acid and 572.9 mg of a mixture of two other caged polyprenylated xanthones were obtained. The mixture was further separated by conventional high-speed counter-current chromatography with a solvent system composed of n-hexane/ethyl acetate/methanol/water (5:5:10:5, v/v/v/v) and n-hexane/methyl tert-butyl ether/acetonitrile/water (8:2:6:4,v/v/v/v), yielding 11.6 mg of isogambogenic acid and 10.4 mg of β-morellic acid from 218.0 mg of the mixture, respectively. The purities of all four of the compounds were over 95%, as determined by high-performance liquid chromatography, and the chemical structures of the four compounds were confirmed by electrospray ionization mass spectrometry and NMR spectroscopy. The combinative application of pH-zone-refining counter-current chromatography and conventional high-speed counter-current chromatography shows great advantages in isolating and enriching the caged polyprenylated xanthones. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Refining processes of selected copper alloys

Directory of Open Access Journals (Sweden)

S. Rzadkosz

2009-04-01

Full Text Available The analysis of the refining effectiveness of the liquid copper and selected copper alloys by various micro additions and special refiningsubstances – was performed. Examinations of an influence of purifying, modifying and deoxidation operations performed in a metal bath on the properties of certain selected alloys based on copper matrix - were made. Refining substances, protecting-purifying slag, deoxidation and modifying substances containing micro additions of such elements as: zirconium, boron, phosphor, sodium, lithium, or their compounds introduced in order to change micro structures and properties of alloys, were applied in examinations. A special attention was directed to macro and micro structures of alloys, their tensile and elongation strength and hot-cracks sensitivity. Refining effects were estimated by comparing the effectiveness of micro structure changes with property changes of copper and its selected alloys from the group of tin bronzes.

Modeling and optimization of the european oil refining capacities and structures on the horizons 1995, 2000 and 2010

International Nuclear Information System (INIS)

Khebri, S.

1993-04-01

This thesis is a study on petroleum refining. In a first part, the author describes the existing refining processes and the structure of refining units, the structure of petroleum consumption and the interfaces with petroleum chemistry industry and gives a retrospect on world and european petroleum refining. In a second part, the author describes the models used to realize the simulation of supplies, market and refining scheme. Four scenarios are developed (conventional wisdom, driving into tensions, sustaining a high economic growth, high prices) and a forecasting on the horizons 1995, 2000 and 2010 is given. 54 refs

Bauxite mining and alumina refining: process description and occupational health risks.

Science.gov (United States)

Donoghue, A Michael; Frisch, Neale; Olney, David

2014-05-01

To describe bauxite mining and alumina refining processes and to outline the relevant physical, chemical, biological, ergonomic, and psychosocial health risks. Review article. The most important risks relate to noise, ergonomics, trauma, and caustic soda splashes of the skin/eyes. Other risks of note relate to fatigue, heat, and solar ultraviolet and for some operations tropical diseases, venomous/dangerous animals, and remote locations. Exposures to bauxite dust, alumina dust, and caustic mist in contemporary best-practice bauxite mining and alumina refining operations have not been demonstrated to be associated with clinically significant decrements in lung function. Exposures to bauxite dust and alumina dust at such operations are also not associated with the incidence of cancer. A range of occupational health risks in bauxite mining and alumina refining require the maintenance of effective control measures.

A clinical data warehouse-based process for refining medication orders alerts.

Science.gov (United States)

Boussadi, Abdelali; Caruba, Thibaut; Zapletal, Eric; Sabatier, Brigitte; Durieux, Pierre; Degoulet, Patrice

2012-01-01

The objective of this case report is to evaluate the use of a clinical data warehouse coupled with a clinical information system to test and refine alerts for medication orders control before they were fully implemented. A clinical decision rule refinement process was used to assess alerts. The criteria assessed were the frequencies of alerts for initial prescriptions of 10 medications whose dosage levels depend on renal function thresholds. In the first iteration of the process, the frequency of the 'exceeds maximum daily dose' alerts was 7.10% (617/8692), while that of the 'under dose' alerts was 3.14% (273/8692). Indicators were presented to the experts. During the different iterations of the process, 45 (16.07%) decision rules were removed, 105 (37.5%) were changed and 136 new rules were introduced. Extensive retrospective analysis of physicians' medication orders stored in a clinical data warehouse facilitates alert optimization toward the goal of maximizing the safety of the patient and minimizing overridden alerts.

Studies of the Action of Grain-Refining Particles in Aluminium Alloys

Science.gov (United States)

Schumacher, P.; Greer, A. L.

Crystallization from a melt and from a metallic glass both occur in an undercooled liquid. In this way identical nucleation mechanisms can operate in the two cases. However, in metallic glasses, unlike conventional solidification at low undercooling, the low atomic mobility permits the resolution and microscopical study of nucleation processes on added particles. Conventional aluminium grain-refiner based on Al-Ti-B has been used to obtain nucleant particles embedded in a glassy matrix of Al85Y8Ni5Co2 (at%). During crystallization from the glassy state, nucleation and growth of α-Al can be observed on TiB2 particles coated with a layer of Al3Ti Empirical relations found in casting practice of Al-alloys, such as excess Ti necessary for grain refinement, can be related to the observed nucleation mechanism, which is found to be very sensitive to both crystallographic and chemical factors.

Chemical and physical aspects of refining coal liquids

Science.gov (United States)

Shah, Y. T.; Stiegel, G. J.; Krishnamurthy, S.

1981-02-01

Increasing costs and declining reserves of petroleum are forcing oil importing countries to develop alternate energy sources. The direct liquefaction of coal is currently being investigated as a viable means of producing substitute liquid fuels. The coal liquids derived from such processes are typically high in nitrogen, oxygen and sulfur besides having a high aromatic and metals content. It is therefore envisaged that modifications to existing petroleum refining technology will be necessary in order to economically upgrade coal liquids. In this review, compositional data for various coal liquids are presented and compared with those for petroleum fuels. Studies reported on the stability of coal liquids are discussed. The feasibility of processing blends of coal liquids with petroleum feedstocks in existing refineries is evaluated. The chemistry of hydroprocessing is discussed through kinetic and mechanistic studies using compounds which are commonly detected in coal liquids. The pros and cons of using conventional petroleum refining catalysts for upgrading coal liquids are discussed.

Influence of emulsifiers on the optimization of processing parameters of refining milk chocolate in the ball mill

Directory of Open Access Journals (Sweden)

Pajin Biljana

2011-01-01

Full Text Available Chocolate manufacture is a complex process which includes a large number of technology operations. One of the obligatory phases is milling, called refining, which aims at obtaining the appropriate distribution of particle size, resulting in the chocolate with optimal physical and sensory characteristics. The aim of this work was to define and optimize the process parameters for the production of milk chocolate by a non-conventional procedure, using the ball mill. The quality of chocolate mass, produced on this way, is determined by measuring the following parameters: moisture, size of the largest cocoa particle, yield flow, and Casson plastic viscosity. A special consideration of this study is the optimization of the types and amounts of emulsifiers, which are responsible for achieving the appropriate rheological and physical characteristics of the chocolate mass. The obtained parameters are compared with those which are typical for the standard procedure.

Influences of different degassing processes on refining effect and properties of 4004 Al alloy

Directory of Open Access Journals (Sweden)

Wang Liping

2013-03-01

Full Text Available In order to improve the plasticity of 4004 Al alloy and subsequently the productivity of 4004 Al foil, the research studied in detail the influence of the rotary impeller degassing process on the refining effect of 4004 Al alloy, in which the impacts of four major parameters: gas flow, rotational speed, refining time, and stewing time, on degassing rate of 4004 Al alloy was systematically studied by using an orthogonal experiment methodology. Results show that the rotational speed has the greatest impact on the degassing of 4004 Al alloy, followed by gas flow and refining time; stewing time has the least impact. The optimum purification parameters obtained by current orthogonal analysis were: rotor speed of 500 r·min-1, inert gas flow of 0.4 mL·h-1, refining time of 15 min, and stewing time of 6 min. Degassing rate using the optimum parameters reaches 68%. In addition, the comparison experiments among C2Cl6 refining, rotary impeller degassing, and combined treatment of C2Cl6 refining and rotary impeller degassing for 4004 Al alloy were performed. The experimental data indicated that the combined treatment of C2Cl6 refining and rotary impeller degassing has the best degassing effect. Degassing rate of C2Cl6 refining, rotary impeller degassing and combined refining treatment is 39%, 69.1% and 76.9%, respectively. The mechanical properties of the specimen refined by rotary impeller degassing were higher than those by C2Cl6 refining, but lower than those by combined refining treatment.

Reversing the conventional leather processing sequence for cleaner leather production.

Science.gov (United States)

Saravanabhavan, Subramani; Thanikaivelan, Palanisamy; Rao, Jonnalagadda Raghava; Nair, Balachandran Unni; Ramasami, Thirumalachari

2006-02-01

Conventional leather processing generally involves a combination of single and multistep processes that employs as well as expels various biological, inorganic, and organic materials. It involves nearly 14-15 steps and discharges a huge amount of pollutants. This is primarily due to the fact that conventional leather processing employs a "do-undo" process logic. In this study, the conventional leather processing steps have been reversed to overcome the problems associated with the conventional method. The charges of the skin matrix and of the chemicals and pH profiles of the process have been judiciously used for reversing the process steps. This reversed process eventually avoids several acidification and basification/neutralization steps used in conventional leather processing. The developed process has been validated through various analyses such as chromium content, shrinkage temperature, softness measurements, scanning electron microscopy, and physical testing of the leathers. Further, the performance of the leathers is shown to be on par with conventionally processed leathers through bulk property evaluation. The process enjoys a significant reduction in COD and TS by 53 and 79%, respectively. Water consumption and discharge is reduced by 65 and 64%, respectively. Also, the process benefits from significant reduction in chemicals, time, power, and cost compared to the conventional process.

Review on the processes of reduction and refining of metallic vanadium

International Nuclear Information System (INIS)

Mourao, M.B.; Capocchi, J.D.T.

1982-01-01

A literature survey on the processes of vanadium reduction and refining is presented. The results achieved by several research workers are comented. Enphasis is given to the aluminothermic reduction of V 2 O 5 followed by purification of the crude metal in an electron beam melting furnace or by high temperature molten salts electrolitic processes. (Author) [pt

Simulation of electrorefining process using time-dependent multi-component electrochemical model: REFIN

Energy Technology Data Exchange (ETDEWEB)

Park, Byung Gi; Hwang, Il Soon [Seoul National Univ., Seoul (Korea, Republic of)

1999-10-01

REFIN model is applied to analyze a series of experiments that had been conducted by Tomczuk, et al. at Argonne National Laboratory (ANL) in the U.S.A.. Predicted results from REFIN model for the electrorefining experiment are compared with the published experimental results. It is demonstrated that REFIN model can predict faradic current of each element and electrochemical potential as a function of time over the entire campaign of the electrorefining experiment. The elemental concentration changes agree with the experimental results well. Elemental concentration changes during an open-circuit equilibration period are revealed to suggest that the electrorefining process could not be adequately described by the equilibrium model often applied for an electrode surface. Surface potential drop is changed according to equilibrium potential of chemical species with high activity in liquid metal.

Kinetic Modeling of a Silicon Refining Process in a Moist Hydrogen Atmosphere

Science.gov (United States)

Chen, Zhiyuan; Morita, Kazuki

2018-06-01

We developed a kinetic model that considers both silicon loss and boron removal in a metallurgical grade silicon refining process. This model was based on the hypotheses of reversible reactions. The reaction rate coefficient kept the same form but error of terminal boron concentration could be introduced when relating irreversible reactions. Experimental data from published studies were used to develop a model that fit the existing data. At 1500 °C, our kinetic analysis suggested that refining silicon in a moist hydrogen atmosphere generates several primary volatile species, including SiO, SiH, HBO, and HBO2. Using the experimental data and the kinetic analysis of volatile species, we developed a model that predicts a linear relationship between the reaction rate coefficient k and both the quadratic function of p(H2O) and the square root of p(H2). Moreover, the model predicted the partial pressure values for the predominant volatile species and the prediction was confirmed by the thermodynamic calculations, indicating the reliability of the model. We believe this model provides a foundation for designing a silicon refining process with a fast boron removal rate and low silicon loss.

Effect of oil refining processes on 14 C-tetrachlorvinphos residues in soya bean oil

International Nuclear Information System (INIS)

Farghaly, M.; Zayed, S.M.A.D.

1986-01-01

Crude soya bean oil extracted from grains treated with 14 C-tetrachlorvinphos and stored for 30 weeks was subjected to different refining processes. The effect of commercial refining processes, namely: alkali treatment, bleaching, winterization and deodorization on the nature and magnitude of the originally present residues was investigated. A high percentage (52%) of the residues was eliminated during alkali neutralization. No potentially toxic materials were detected among the identified degradation products. The obtained data showed that the ultimate degradation products were dimethyl phosphate and mono methyl phosphate.2 tab.,2 scheme

Microstructure evolution and grain refinement of Ti-6Al-4V alloy by laser shock processing

Energy Technology Data Exchange (ETDEWEB)

Ren, X.D., E-mail: renxd@mail.ujs.edu.cn [Department of Mechanical Engineering, Jiangsu University, Zhenjiang, 212013 (China); Research Center of Fluid Machinery Engineering and Technical, Jiangsu University, Zhenjiang, 212013 (China); Zhou, W.F.; Liu, F.F.; Ren, Y.P. [Department of Mechanical Engineering, Jiangsu University, Zhenjiang, 212013 (China); Yuan, S.Q. [Research Center of Fluid Machinery Engineering and Technical, Jiangsu University, Zhenjiang, 212013 (China); Ren, N.F.; Xu, S.D.; Yang, T. [Department of Mechanical Engineering, Jiangsu University, Zhenjiang, 212013 (China)

2016-02-15

Graphical abstract: The grain refinement process of Ti-6Al-4V alloy under LSP: (a) LDD in original grains; (b) Dislocations in β phase; (c) DTIs in α phase; (d) DTs transform into DCs; (e) DWs develop into sub-GBs; (f) GR accomplishes. - Highlights: • LSP could repair the surface defects and reduce the surface roughness. • Microstructure evolution of α phase in Ti-6Al-4V alloy processed by LSP is distinct from β phase. • Multidirectional twin intersections and subgrain boundaries are the main mechanism of grain refinement of Ti-6Al-4V alloy. • Grain refinement process of the Ti-6Al-4V alloy was illustrated. - Abstract: Microstructure evolution and grain refinement of Ti-6Al-4V alloy after laser shock processing (LSP) are systematically investigated in this paper. Laser shock waves were induced by a Q-switched Nd:YAG laser system operated with a wave-length of 1064 nm and 10 ns pulse width. The microstructures of LSP samples were characterized by scanning electron microscopy (SEM) and transmission electron microscope (TEM). Present results indicate that the surface hardness of samples subjected to LSP impacts has significantly improved. Multidirectional twin intersections and dislocation movements lead to grain subdivision in α phase with ultra-high plastic deformation. High-density dislocations are found in β phase. Multidirectional twin intersections and division of sub-grain boundaries play an important role in the grain refinement of Ti-6Al-4V alloy under LSP loading conditions.

Preparative Separation of Alkaloids from Picrasma quassioides (D. Don Benn. by Conventional and pH-Zone-Refining Countercurrent Chromatography

Directory of Open Access Journals (Sweden)

Qinghai Zhang

2014-06-01

Full Text Available Two high-speed countercurrent chromatography (HSCCC modes were compared by separation of major alkaloids from crude extract of Picrasma quassioides. The conventional HSCCC separation was performed with a two-phase solvent system composed of petroleum ether–ethyl acetate–methanol–water (5:5:4.5:5.5, v/v/v/v with 200 mg loading. pH-Zone-refining CCC was performed with two-phase solvent system composed of petroleum ether–ethyl acetate–n-butanol–water (3:2:7:9, v/v/v/v where triethylamine (10 mM was added to the upper organic stationary phase and hydrochloric acid (5 mM was added to the lower aqueous phase with 2 g loading. From 2 g of crude extract, 87 mg of 5-methoxycanthin-6-one (a, 38 mg of 1-methoxy-β-carboline (b, 134 mg of 1-ethyl-4,8-dimethoxy-β-carboline (c, 74 mg of 1-ethoxycarbonyl-β-carboline (d, 56 mg of 1-vinyl-4,8-dimethoxy-β-carboline (e and 26 mg of 1-vinyl-4-dimethoxy-β-carboline (f were obtained with purities of over 97.0%. The results indicated that pH-zone-refining CCC is an excellent separations tool at the multigram level.

The effect of coarse second-phase particles on the rate of grain refinement during severe deformation processing

DEFF Research Database (Denmark)

Apps, P.J.; Bowen, Jacob R.; Prangnell, P.B.

2003-01-01

The effect of second-phase particles on the rate of grain refinement during severe deformation processing has been investigated, by comparing the microstructure evolution in an AA8079 aluminium alloy, containing 2.5 vol.% of ~2 μm particles, with that in a high purity, single-phase, Al-0.13% Mg a...... by an effective strain of only five in the particle-containing alloy, compared to ten in the single-phase material. The mechanisms that contribute to this acceleration of the grain refinement process are discussed.......The effect of second-phase particles on the rate of grain refinement during severe deformation processing has been investigated, by comparing the microstructure evolution in an AA8079 aluminium alloy, containing 2.5 vol.% of ~2 μm particles, with that in a high purity, single-phase, Al-0.13% Mg...... alloy, deformed identically by ECAE to an effective strain of ten. The materials were analysed by high-resolution EBSD orientation mapping, which revealed that grain refinement occurred at a dramatically higher rate in the particle-containing alloy. A submicron grain structure could be achieved...

Enzymatic Refining and Cellulose Nanofiber Addition in Papermaking Processes from Recycled and Deinked Slurries

Directory of Open Access Journals (Sweden)

Marc Delgado-Aguilar

2015-07-01

Full Text Available Recycling and deinking processes cause fiber damage because of hornification phenomena and increased external fibrillation. Mechanical refining has been used for many years to enhance the mechanical properties of paper. Biorefining of pulp using enzymes is receiving increasing interest for energy reduction at the refining step of the paper-making process. Moreover, enzymes have also been used for the enhancement of mechanical properties without affecting the drainage rate. As an alternative to mechanical refining treatment, a combination of an enzymatic treatment and cellulose nanofibril (CNF addition was explored to enhance the mechanical properties of paper. The tests were carried out on a deinked pulp (DIP suspension made of 50% old newspapers (ONP and 50% old magazines (OMG. Various enzyme charges and CNF amounts were added to the mixture of ONP and OMG. All pulps (treated and untreated were characterized from a morphological point of view, and the paper sheets made thereof were mechanically characterized. The combination of the enzymatic treatment with the addition of 3% CNF provided sufficient tensile strength for the paper to be used in high-performance applications.

Development of an efficient grain refiner for Al-7Si alloy

Energy Technology Data Exchange (ETDEWEB)

Kori, S.A.; Murty, B.S.; Chakraborty, M. [Indian Inst. of Technol., Kharagpur (India). Dept. of Metall. and Mater. Eng.

2000-03-15

The response of Al-7Si alloy towards grain refinement by Al-Ti-B master alloys (with different Ti-B ratios) at different addition levels has been studied in detail. The results indicate that high B-containing master alloys are powerful grain refiners when compared to conventional grain refiners like Al-5Ti-lB master alloys. In the present study, indigenously developed master alloys have been used for the grain refinement of alloys Al-7Si and LM-25. Significant improvements in mechanical properties have been obtained with a combination of grain refiner and Sr as modifier. (orig.)

Optimization of Refining Craft for Vegetable Insulating Oil

Science.gov (United States)

Zhou, Zhu-Jun; Hu, Ting; Cheng, Lin; Tian, Kai; Wang, Xuan; Yang, Jun; Kong, Hai-Yang; Fang, Fu-Xin; Qian, Hang; Fu, Guang-Pan

2016-05-01

Vegetable insulating oil because of its environmental friendliness are considered as ideal material instead of mineral oil used for the insulation and the cooling of the transformer. The main steps of traditional refining process included alkali refining, bleaching and distillation. This kind of refining process used in small doses of insulating oil refining can get satisfactory effect, but can't be applied to the large capacity reaction kettle. This paper using rapeseed oil as crude oil, and the refining process has been optimized for large capacity reaction kettle. The optimized refining process increases the acid degumming process. The alkali compound adds the sodium silicate composition in the alkali refining process, and the ratio of each component is optimized. Add the amount of activated clay and activated carbon according to 10:1 proportion in the de-colorization process, which can effectively reduce the oil acid value and dielectric loss. Using vacuum pumping gas instead of distillation process can further reduce the acid value. Compared some part of the performance parameters of refined oil products with mineral insulating oil, the dielectric loss of vegetable insulating oil is still high and some measures are needed to take to further optimize in the future.

Detecting Difference between Process Models Based on the Refined Process Structure Tree

Directory of Open Access Journals (Sweden)

Jing Fan

2017-01-01

Full Text Available The development of mobile workflow management systems (mWfMS leads to large number of business process models. In the meantime, the location restriction embedded in mWfMS may result in different process models for a single business process. In order to help users quickly locate the difference and rebuild the process model, detecting the difference between different process models is needed. Existing detection methods either provide a dissimilarity value to represent the difference or use predefined difference template to generate the result, which cannot reflect the entire composition of the difference. Hence, in this paper, we present a new approach to solve this problem. Firstly, we parse the process models to their corresponding refined process structure trees (PSTs, that is, decomposing a process model into a hierarchy of subprocess models. Then we design a method to convert the PST to its corresponding task based process structure tree (TPST. As a consequence, the problem of detecting difference between two process models is transformed to detect difference between their corresponding TPSTs. Finally, we obtain the difference between two TPSTs based on the divide and conquer strategy, where the difference is described by an edit script and we make the cost of the edit script close to minimum. The extensive experimental evaluation shows that our method can meet the real requirements in terms of precision and efficiency.

Science, technology and environmental demands: innovations in oil refining process; Ciencia, tecnologia e demandas ambientais: inovacoes nos processos de refino

Energy Technology Data Exchange (ETDEWEB)

Azevedo, Adalberto Mantovani Martiniano de [Universidade Estadual de Campinas, SP (Brazil). Inst. de Geociencias. Programa de Pos-graduacao do Departamento de Politica Cientifica e Tecnologica

2003-07-01

This paper consists in a survey about changes in oil refining technologies caused by an increase of external environmental restrictions, that create demands for innovations related to the reduction of environmental impacts in refining processes and products. The environmental restrictions considered in this paper include state regulation, like the control over solid and gas wastes and the control over levels of air pollutants on refined products. Another group of restrictions include market restrictions, mainly the restrictions for obtaining 'green' quality labels, like ISO 14000. The paper will show the main environmental restrictions for the Paulinia Refinery (REPLAN), and its reaction in introducing innovations in refining processes. Some aspects of the innovations observed will be described, like the kind of innovation (process or product), the institutions that created innovations and their resources, the knowledge fields applied, and another characteristics for the evaluation of environmental influence over the development on oil refining innovations. (author)

Safety, Liveness and Run-time Refinement for Modular Process-Aware Information Systems with Dynamic Sub Processes

DEFF Research Database (Denmark)

Debois, Søren; Hildebrandt, Thomas; Slaats, Tijs

2015-01-01

and verification of flexible, run-time adaptable process-aware information systems, moved into practice via the Dynamic Condition Response (DCR) Graphs notation co-developed with our industrial partner. Our key contributions are: (1) A formal theory of dynamic sub-process instantiation for declarative, event......We study modularity, run-time adaptation and refinement under safety and liveness constraints in event-based process models with dynamic sub-process instantiation. The study is part of a larger programme to provide semantically well-founded technologies for modelling, implementation......-based processes under safety and liveness constraints, given as the DCR* process language, equipped with a compositional operational semantics and conservatively extending the DCR Graphs notation; (2) an expressiveness analysis revealing that the DCR* process language is Turing-complete, while the fragment cor...

Oil refining expansion criteria for Brazil

International Nuclear Information System (INIS)

Tavares, M.E.E.; Szklo, A.S.; Machado, G.V.; Schaeffer, R.; Mariano, J.B.; Sala, J.F.

2006-01-01

This paper assesses different strategies for the expansion of Brazil's oil refining segment, using criteria that range from energy security (reducing imports and vulnerability for key products) through to maximizing the profitability of this sector (boosting the output of higher value oil products) and adding value to Brazil's oil production (reducing exports of heavy acid oil). The development prospects are analyzed for conventional fuel production technology routes, sketching out three possible refining schemes for Brazilian oil and a GTL plant for producing gasoil from natural gas. Market scenario simulations indicate that investments will be required in Brazil's oil refining segment over and above those allocated to planned modifications in its current facilities, reducing the nation's vulnerability in terms of gasoil and petrochemical naphtha imports. Although not economically attractive, oil refining is a key activity that is crucial to oil company strategies. The decision to invest in this segment depends on local infrastructure conditions, environmental constraints and fuel specifications, in addition to oil company strategies, steady growth in demand and the definition of a government policy that eases institutional risks. (author)

Oil refining expansion criteria for Brazil

International Nuclear Information System (INIS)

Tavares, Marina Elisabete Espinho; Szklo, Alexandre Salem; Machado, Giovani Vitoria; Schaeffer, Roberto; Mariano, Jacqueline Barboza; Sala, Janaina Francisco

2006-01-01

This paper assesses different strategies for the expansion of Brazil's oil refining segment, using criteria that range from energy security (reducing imports and vulnerability for key products) through to maximizing the profitability of this sector (boosting the output of higher value oil products) and adding value to Brazil's oil production (reducing exports of heavy acid oil). The development prospects are analyzed for conventional fuel production technology routes, sketching out three possible refining schemes for Brazilian oil and a GTL plant for producing gasoil from natural gas. Market scenario simulations indicate that investments will be required in Brazil's oil refining segment over and above those allocated to planned modifications in its current facilities, reducing the nation's vulnerability in terms of gasoil and petrochemical naphtha imports. Although not economically attractive, oil refining is a key activity that is crucial to oil company strategies. The decision to invest in this segment depends on local infrastructure conditions, environmental constraints and fuel specifications, in addition to oil company strategies, steady growth in demand and the definition of a government policy that eases institutional risks

Grain refinement and mechanical properties of CP-Ti processed by warm accumulative roll bonding

International Nuclear Information System (INIS)

Milner, Justin L.; Abu-Farha, Fadi; Bunget, Cristina; Kurfess, Thomas; Hammond, Vincent H.

2013-01-01

Accumulative roll bonding (ARB), a severe plastic deformation technique, was used in this study to process commercially pure titanium (CP-Ti) at 450 °C. Sheet samples were processed by seven consecutive ARB cycles, with an overall equivalent strain of 5.6. Mechanical characterization and microstructural examination were carried out on the processed material to track their changes and relationships with regard to one another. Electron microscopy, TEM in particular, revealed significant grain refinement in the material, with submicron microstructure achieved even after one cycle of warm processing. Further processing was shown to progressively fragment the highly elongated grains, ultimately producing a predominantly-equiaxed ultrafine grain structure with an average grain size of ∼100 nm. Tensile strength and microhardness of the material increased with the number of ARB cycles; the strength–grain size relationship followed the Hall–Petch equation. The overall grain refinement and strengthening levels observed here are close to those reported in the literature for ARB processing of CP-Ti at ambient temperatures. This demonstrates the ability of warm ARB can be as effective as cold ARB, while offering several advantages for industrial utilization.

Grain refinement of aluminum and its alloys

International Nuclear Information System (INIS)

Zaid, A.I.O.

2001-01-01

Grain refinement of aluminum and its alloys by the binary Al-Ti and Ternary Al-Ti-B master alloys is reviewed and discussed. The importance of grain refining to the cast industry and the parameters affecting it are presented and discussed. These include parameters related to the cast, parameters related to the grain refining alloy and parameters related to the process. The different mechanisms, suggested in the literature for the process of grain refining are presented and discussed, from which it is found that although the mechanism of refining by the binary Al-Ti is well established the mechanism of grain refining by the ternary Al-Ti-B is still a controversial matter and some research work is still needed in this area. The effect of the addition of other alloying elements in the presence of the grain refiner on the grain refining efficiency is also reviewed and discussed. It is found that some elements e.g. V, Mo, C improves the grain refining efficiency, whereas other elements e.g. Cr, Zr, Ta poisons the grain refinement. Based on the parameters affecting the grain refinement and its mechanism, a criterion for selection of the optimum grain refiner is forwarded and discussed. (author)

Process to refine flyash captured from pulverized coal fired boilers and auxiliary equipment

International Nuclear Information System (INIS)

Borowy, W.J.

1991-01-01

This patent describes a separating and refining process for particulate that has been removed from the exhaust gases of an organic fuel combustion process. It includes determining relative sizes of carbon rich and carbon lean particles that are found in the exhaust gases for the combustion process; supplying the particulate matter from the exhaust of the combustion process; providing a means for conveying the particulate matter between the following steps; separating, by size, coarse and fine particles in the exhaust particulate so as to yield carbon rich and carbon lean fractions

Comparing Syntactic and Semantics Action Refinement

NARCIS (Netherlands)

Goltz, Ursula; Gorrieri, Roberto; Rensink, Arend

The semantic definition of action refinement on labelled configuration structures is compared with the notion of syntactic substitution, which can be used as another notion of action refinement in a process algebraic setting. The comparison is done by studying a process algebra equipped with

Process to Continuously Melt, Refine and Cast High Quality Steel

Energy Technology Data Exchange (ETDEWEB)

None

2005-09-01

The purpose of this project is to conduct research and development targeted at designing a revolutionary steelmaking process. This process will deliver high quality steel from scrap to the casting mold in one continuous process and will be safer, more productive, and less capital intensive to build and operate than conventional steelmaking. The new process will produce higher quality steel faster than traditional batch processes while consuming less energy and other resources.

Grain Refinement of Freeform Fabricated Ti-6Al-4V Alloy Using Beam/Arc Modulation

Science.gov (United States)

Mitzner, Scott; Liu, Stephen; Domack, Marcia S.; Hafley, Robert A.

2012-01-01

Grain refinement can significantly improve the mechanical properties of freeform-fabricated Ti-6Al-4V alloy, promoting increased strength and enhanced isotropy compared with coarser grained material. Large beta-grains can lead to a segregated microstructure, in regard to both alpha-phase morphology and alpha-lath orientation. Beam modulation, which has been used in conventional fusion welding to promote grain refinement, is explored in this study for use in additive manufacturing processes including electron beam freeform fabrication (EBF(sup 3)) and gas-tungsten arc (GTA) deposition to alter solidification behavior and produce a refined microstructure. The dynamic molten pool size induced by beam modulation causes rapid heat flow variance and results in a more competitive grain growth environment, reducing grain size. Consequently, improved isotropy and strength can be achieved with relatively small adjustments to deposition parameters.

Assessing corrosion in oil refining and petrochemical processing

Directory of Open Access Journals (Sweden)

Randy C. John

2004-03-01

Full Text Available This paper summarizes the development of an information system used to manage corrosion of metals and alloys by high temperature gases found in many different oil refining, petrochemical, power generation, and chemical processes. The database currently represents about 7.9 million h of exposure time for about 5,500 tests with 89 commercial alloys for a temperature range of 200 - 1,200°C. The system manages corrosion data from well-defined exposures and determines corrosion product stabilities. New models used in the analysis of thermochemical data for the Fe-Ni-Cr-Co-C-O-S-N-H system are being compiled. All known phases based upon combinations of the elements have been analyzed to allow complete assessments of corrosion product stabilities. Use of these data allows prediction of stable corrosion products and hence identification of the possible dominant corrosion mechanisms. The system has the potential to be used in corrosion research, alloy development, failure analysis, lifetime prediction, and process operations evaluations. The corrosion mechanisms emphasized are oxidation, sulfidation, sulfidation/oxidation, and carburization.

On Syntactic and Semantic Action Refinement

NARCIS (Netherlands)

Hagiya, M.; Goltz, U.; Mitchell, J.C.; Gorrieri, R.; Rensink, Arend

1994-01-01

The semantic definition of action refinement on labelled event structures is compared with the notion of syntactic substitution, which can be used as another notion of action refinement in a process algebraic setting. This is done by studying a process algebra equipped with the ACP sequential

Synthesis of Titania-supported Copper Nanoparticles via Refined Alkoxide Sol-gel Process

International Nuclear Information System (INIS)

Wu, Jeffrey C.S.; Tseng, I.-Hsiang; Chang, W.-C.

2001-01-01

Nanoparticles of titania and copper-loaded titania were synthesized by a refined sol-gel method using titanium butoxide. Unlike the conventional sol-gel procedure of adding water directly, the esterification of anhydrous butanol and glacial acetic acid provided the hydrolyzing water. In addition, acetic acid also served as a chelating ligand to stabilize the hydrolysis-condensation process and minimize the agglomeration of titania. Following the hydrolysis, Cu/TiO 2 was prepared by adding copper chloride to titania sol. The sol was dried, then calcined at 500 deg. C to remove organics and transformed to anatase titania which was verified by XRD. Cu/TiO 2 was further hydrogen-reduced at 300 deg. C. The recovery of Ti was exceeded by an average of 95% from titanium butoxide. TEM micrographs show that the Cu/TiO 2 particles are near uniform. The average crystallite sizes are 17-20 nm estimated from the peak broadening of XRD spectra. The bandgaps of TiO 2 and reduced Cu/TiO 2 range from 2.70 to 3.15 eV estimated from the diffusive reflective UV-Vis spectra. XPS analysis shows that Cu 2p 3/2 is 933.4 eV indicating primary Cu 2 O form on the TiO 2 supports. The binding energy of Ti does not exhibit chemical shift suggesting negligible interaction of Cu cluster and TiO 2 support

Synthesis of Titania-supported Copper Nanoparticles via Refined Alkoxide Sol-gel Process

Science.gov (United States)

Wu, Jeffrey C. S.; Tseng, I.-Hsiang; Chang, Wan-Chen

2001-06-01

Nanoparticles of titania and copper-loaded titania were synthesized by a refined sol-gel method using titanium butoxide. Unlike the conventional sol-gel procedure of adding water directly, the esterification of anhydrous butanol and glacial acetic acid provided the hydrolyzing water. In addition, acetic acid also served as a chelating ligand to stabilize the hydrolysis-condensation process and minimize the agglomeration of titania. Following the hydrolysis, Cu/TiO2 was prepared by adding copper chloride to titania sol. The sol was dried, then calcined at 500°C to remove organics and transformed to anatase titania which was verified by XRD. Cu/TiO2 was further hydrogen-reduced at 300°C. The recovery of Ti was exceeded by an average of 95% from titanium butoxide. TEM micrographs show that the Cu/TiO2 particles are near uniform. The average crystallite sizes are 17-20 nm estimated from the peak broadening of XRD spectra. The bandgaps of TiO2 and reduced Cu/TiO2 range from 2.70 to 3.15 eV estimated from the diffusive reflective UV-Vis spectra. XPS analysis shows that Cu 2p3/2 is 933.4 eV indicating primary Cu2O form on the TiO2 supports. The binding energy of Ti does not exhibit chemical shift suggesting negligible interaction of Cu cluster and TiO2 support.

Synthesis of Titania-supported Copper Nanoparticles via Refined Alkoxide Sol-gel Process

Energy Technology Data Exchange (ETDEWEB)

Wu, Jeffrey C.S., E-mail: Cswu@ccms.ntu.edu.tw; Tseng, I.-Hsiang; Chang, W.-C. [National Taiwan University, Department of Chemical Engineering (China)

2001-06-15

Nanoparticles of titania and copper-loaded titania were synthesized by a refined sol-gel method using titanium butoxide. Unlike the conventional sol-gel procedure of adding water directly, the esterification of anhydrous butanol and glacial acetic acid provided the hydrolyzing water. In addition, acetic acid also served as a chelating ligand to stabilize the hydrolysis-condensation process and minimize the agglomeration of titania. Following the hydrolysis, Cu/TiO{sub 2} was prepared by adding copper chloride to titania sol. The sol was dried, then calcined at 500 deg. C to remove organics and transformed to anatase titania which was verified by XRD. Cu/TiO{sub 2} was further hydrogen-reduced at 300 deg. C. The recovery of Ti was exceeded by an average of 95% from titanium butoxide. TEM micrographs show that the Cu/TiO{sub 2} particles are near uniform. The average crystallite sizes are 17-20 nm estimated from the peak broadening of XRD spectra. The bandgaps of TiO{sub 2} and reduced Cu/TiO{sub 2} range from 2.70 to 3.15 eV estimated from the diffusive reflective UV-Vis spectra. XPS analysis shows that Cu 2p{sub 3/2} is 933.4 eV indicating primary Cu{sub 2}O form on the TiO{sub 2} supports. The binding energy of Ti does not exhibit chemical shift suggesting negligible interaction of Cu cluster and TiO{sub 2} support.

Realization of the Zone Length Measurement during Zone Refining Process via Implementation of an Infrared Camera

Directory of Open Access Journals (Sweden)

Danilo C. Curtolo

2018-05-01

Full Text Available Zone refining, as the currently most common industrial process to attain ultrapure metals, is influenced by a variety of factors. One of these parameters, the so-called “zone length”, affects not only the ultimate concentration distribution of impurities, but also the rate at which this distribution is approached. This important parameter has however neither been investigated experimentally, nor ever varied for the purpose of optimization. This lack of detections may be due to the difficult temperature measurement of a moving molten area in a vacuum system, of which the zone refining methodology is comprised. Up to now, numerical simulation as a combination of complex mathematical calculations, as well as many assumptions has been the only way to reveal it. This paper aims to propose an experimental method to accurately measure the molten zone length and to extract helpful information on the thermal gradient, temperature profile and real growth rate in the zone refining of an exemplary metal, in this case aluminum. This thermographic method is based on the measurement of the molten surface temperature via an infrared camera, as well as further data analysis through the mathematical software MATLAB. The obtained results show great correlation with the visual observations of zone length and provide helpful information to determine the thermal gradient and real growth rate during the whole process. The investigations in this paper approved the application of an infrared camera for this purpose as a promising technique to automatically control the zone length during a zone refining process.

Analysis of Drying Process Quality in Conventional Dry-Kilns

OpenAIRE

Sedlar Tomislav; Pervan Stjepan

2010-01-01

This paper presents testing results of drying quality in a conventional dry kiln. Testing is based on a new methodology that will show the level of success of the drying process management by analyzing the quality of drying process in a conventional dry kiln, using a scientifi cally improved version of the check list in everyday practical applications. A company that specializes in lamel and classic parquet production was chosen so as to verify the new testing methodology. A total of 56 m3 of...

Substitute Energy Carriers from Refinement of Coal using HTR-Module

International Nuclear Information System (INIS)

Barnert, Heiko; Kugeler, Kurt; Will, Michael

2014-01-01

There is a revival of coal refinement in the world: a recent press article in Germany titled “The Renaissance of Coal Refinement”. It reports about a large number of conventional plans and plants for coal refinement in many countries in the world, and in particular in China. Nuclear energy can be of assistance, in particular the High Temperature Reactor-Module, because it offers all needed process energies. The status of the research, development, and demonstration, RDD, of technology is summarized, in particular of the former programs in Germany: The primary energy carriers were hard coal and lignite. The envisaged products were: Substitute Natural Gas, SNG, for the gas market, Hydrogen, H2, for a future H2-market, e.g. for airplane traffic, Liquid Fuels, as Substitute Gasoline, or as Energy Alcohol, e.g. Methanol CH3OH, in mixture with higher alcohols, for the car traffic and for home heating. (author)

New antipollution processing of a used refining catalyst and complete recovery of the catalyst metallic components

Energy Technology Data Exchange (ETDEWEB)

Trinh Dinh Chan; Llido, E.

1992-05-15

The used refining catalyst, containing metals such as vanadium, nickel and iron, is first processed by stripping; it is then calcined in critical conditions and heat processed in the presence of a melted alkaline base; the resulting solid matter is then water processed. The antipollution process can be applied to oil fraction hydroconversion or hydroprocessing catalysts.

Optimization bitumen-based upgrading and refining schemes

Energy Technology Data Exchange (ETDEWEB)

Munteanu, M.; Chen, J. [National Centre for Upgrading Technology, Devon, AB (Canada); Natural Resources Canada, Devon, AB (Canada). CanmetENERGY

2009-07-01

This poster highlighted the results of a study in which the entire refining scheme for Canadian bitumen as feedstocks was modelled and simulated under different process configurations, operating conditions and product structures. The aim of the study was to optimize the economic benefits, product quality and energy use under a range of operational scenarios. Optimal refining schemes were proposed along with process conditions for existing refinery configurations and objectives. The goal was to provide guidelines and information for upgrading and refining process design and retrofitting. Critical steps were identified with regards to the upgrading process. It was concluded that the information obtained from this study would lead to significant improvement in process performance and operations, and in reducing the capital cost for building new upgraders and refineries. The simulation results provided valuable information for increasing the marketability of bitumen, reducing greenhouse gas emissions and other environmental impacts associated with bitumen upgrading and refining. tabs., figs.

Isolation of a furan fatty acid from Hevea brasiliensis latex employing the combined use of pH-zone-refining and conventional countercurrent chromatography.

Science.gov (United States)

Englert, Michael; Ulms, Kerstin; Wendlinger, Christine; Vetter, Walter

2016-02-01

Furan fatty acids are valuable and bioactive minor fatty acids that usually contribute chromatography. A first run using pH-zone-refining countercurrent chromatography provided 48.4 mg of 9-(3-methyl-5-pentylfuran-2-yl)-nonanoic acid from 210 mg latex extract in a purity of 95%. The purity was increased to 99% by means of one second run in conventional countercurrent chromatography mode. The Structure and purity of 9-(3-methyl-5-pentylfuran-2-yl)-nonanoic acid were determined by gas chromatography coupled to mass spectrometry and (1)H and (13)C NMR spectroscopy. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Guidelines regarding the Review Process under the Convention on Nuclear Safety

International Nuclear Information System (INIS)

2013-01-01

These Guidelines, established by the Contracting Parties pursuant to Article 22 of the Convention, are intended to be read in conjunction with the text of the Convention. Their purpose is to provide guidance to the Contracting Parties on the process for reviewing National Reports submitted in accordance with Article 5 of the Convention and thereby to facilitate the efficient review of implementation by the Contracting Parties of their obligations under the Convention. The aim of the review process should be to achieve a thorough examination of National Reports submitted in accordance with Article 5 of the Convention, so that Contracting Parties can learn from each other's solutions to common and individual nuclear safety problems and, above all, contribute to improving nuclear safety worldwide through a constructive exchange of views. [fr

Guidelines regarding the Review Process under the Convention on Nuclear Safety

International Nuclear Information System (INIS)

2013-01-01

These Guidelines, established by the Contracting Parties pursuant to Article 22 of the Convention, are intended to be read in conjunction with the text of the Convention. Their purpose is to provide guidance to the Contracting Parties on the process for reviewing National Reports submitted in accordance with Article 5 of the Convention and thereby to facilitate the efficient review of implementation by the Contracting Parties of their obligations under the Convention. The aim of the review process should be to achieve a thorough examination of National Reports submitted in accordance with Article 5 of the Convention, so that Contracting Parties can learn from each other's solutions to common and individual nuclear safety problems and, above all, contribute to improving nuclear safety worldwide through a constructive exchange of views.

Guidelines regarding the Review Process under the Convention on Nuclear Safety

International Nuclear Information System (INIS)

2013-01-01

These Guidelines, established by the Contracting Parties pursuant to Article 22 of the Convention, are intended to be read in conjunction with the text of the Convention. Their purpose is to provide guidance to the Contracting Parties on the process for reviewing National Reports submitted in accordance with Article 5 of the Convention and thereby to facilitate the efficient review of implementation by the Contracting Parties of their obligations under the Convention. The aim of the review process should be to achieve a thorough examination of National Reports submitted in accordance with Article 5 of the Convention, so that Contracting Parties can learn from each other's solutions to common and individual nuclear safety problems and, above all, contribute to improving nuclear safety worldwide through a constructive exchange of views. [es

Grain refinement in a AlZnMgCuTi alloy by intensive melt shearing: A multi-step nucleation mechanism

Science.gov (United States)

Li, H. T.; Xia, M.; Jarry, Ph.; Scamans, G. M.; Fan, Z.

2011-01-01

Direct chill (DC) cast ingots of wrought Al alloys conventionally require the deliberate addition of a grain refiner to provide a uniform as-cast microstructure for the optimisation of both mechanical properties and processability. Grain refiner additions have been in widespread industrial use for more than half a century. Intensive melt shearing can provide grain refinement without the need for a specific grain refiner addition for both magnesium and aluminium based alloys. In this paper we present experimental evidence of the grain refinement in an experimental wrought aluminium alloy achieved by intensive melt shearing in the liquid state prior to solidification. The mechanisms for high shear induced grain refinement are correlated with the evolution of oxides in alloys. The oxides present in liquid aluminium alloys, normally as oxide films and clusters, can be effectively dispersed by intensive shearing and then provide effective sites for the heterogeneous nucleation of Al 3Ti phase. As a result, Al 3Ti particles with a narrower size distribution and hence improved efficiency as active nucleation sites of α-aluminium grains are responsible for the achieved significant grain refinement. This is termed a multi-step nucleation mechanism.

Solvent-refined-coal (SRC) process. Volume II. Sections V-XIV. Final report

Energy Technology Data Exchange (ETDEWEB)

1982-05-01

This report documents the completion of development work on the Solvent Refined Coal Process by The Pittsburgh and Midway Coal Mining Co. The work was initiated in 1966 under Office of Coal Research, US Department of Interior, Contract No. 14-01-0001-496 and completed under US Department of Energy Contract No. DE-AC05-79ET10104. This report discusses work leading to the development of the SRC-I and SRC-II processes, construction of the Fort Lewis Pilot Plant for the successful development of these processes, and results from the operation of this pilot plant. Process design data generated on a 1 ton-per-day Process Development Unit, bench-scale units and through numerous research projects in support of the design of major demonstration plants are also discussed in summary form and fully referenced in this report.

Towards automated crystallographic structure refinement with phenix.refine

Energy Technology Data Exchange (ETDEWEB)

Afonine, Pavel V., E-mail: pafonine@lbl.gov; Grosse-Kunstleve, Ralf W.; Echols, Nathaniel; Headd, Jeffrey J.; Moriarty, Nigel W. [Lawrence Berkeley National Laboratory, One Cyclotron Road, MS64R0121, Berkeley, CA 94720 (United States); Mustyakimov, Marat; Terwilliger, Thomas C. [Los Alamos National Laboratory, M888, Los Alamos, NM 87545 (United States); Urzhumtsev, Alexandre [CNRS–INSERM–UdS, 1 Rue Laurent Fries, BP 10142, 67404 Illkirch (France); Université Henri Poincaré, Nancy 1, BP 239, 54506 Vandoeuvre-lès-Nancy (France); Zwart, Peter H. [Lawrence Berkeley National Laboratory, One Cyclotron Road, MS64R0121, Berkeley, CA 94720 (United States); Adams, Paul D. [Lawrence Berkeley National Laboratory, One Cyclotron Road, MS64R0121, Berkeley, CA 94720 (United States); University of California Berkeley, Berkeley, CA 94720 (United States)

2012-04-01

phenix.refine is a program within the PHENIX package that supports crystallographic structure refinement against experimental data with a wide range of upper resolution limits using a large repertoire of model parameterizations. This paper presents an overview of the major phenix.refine features, with extensive literature references for readers interested in more detailed discussions of the methods. phenix.refine is a program within the PHENIX package that supports crystallographic structure refinement against experimental data with a wide range of upper resolution limits using a large repertoire of model parameterizations. It has several automation features and is also highly flexible. Several hundred parameters enable extensive customizations for complex use cases. Multiple user-defined refinement strategies can be applied to specific parts of the model in a single refinement run. An intuitive graphical user interface is available to guide novice users and to assist advanced users in managing refinement projects. X-ray or neutron diffraction data can be used separately or jointly in refinement. phenix.refine is tightly integrated into the PHENIX suite, where it serves as a critical component in automated model building, final structure refinement, structure validation and deposition to the wwPDB. This paper presents an overview of the major phenix.refine features, with extensive literature references for readers interested in more detailed discussions of the methods.

Effects of slag composition and process variables on decontamination of metallic wastes by melt refining

International Nuclear Information System (INIS)

Heshmatpour, B.; Copeland, G.L.

1981-01-01

Melt refining has been suggested as an alternative for decontamination and volume reduction of low-level-contaminated metallic wastes. Knowledge of metallurgical and thermochemical aspects of the process is essential for effective treatment of various metals. Variables such as slag type and composition, melting technique, and refractory materials need to be identified for each metal or alloy. Samples of contaminated metals were melted with fluxes by resistance furnace or induction heating. The resulting ingots as well as the slags were analyzed for their nuclide contents, and the corresponding partition ratios were calculated. Compatibility of slags and refractories was also investigated, and proper refractory materials were identified. Resistance furnace melting appeared to be a better melting technique for nonferrous scrap, while induction melting was more suitable for ferrous metals. In general uranium contents of the metals, except for aluminum, could be reduced to as low as 0.01 to 0.1 ppM by melt refining. Aluminum could be decontaminated to about 1 to 2 ppM U when certain fluoride slags were used. The extent of decontamination was not very sensitive to slag type and composition. However, borosilicate and basic oxidizing slags were more effective on ferrous metals and Cu; NaNO 3 -NaCl-NaOH type fluxes were desirable for Zn, Pb, and Sn; and fluoride type slags were effective for decontamination of Al. Recrystallized alumina proved to be the most compatible refractory for melt refining both ferrous and nonferrous metals, while graphite was suitable for nonferrous metal processing. In conclusion, melt refining is an effective technique for volume reduction ad decontamination of contaminated metal scrap when proper slags, melting technique, and refractories are used

Grain refinement and hardness distribution in cryogenically cooled ferritic stainless steel welds

International Nuclear Information System (INIS)

Amuda, M.O.H.; Mridha, S.

2013-01-01

Highlights: ► Grain refinement was undertaken in AISI 430 FSS welds using cryogenic cooling. ► Flow rates of the cryogenic liquid influenced weld grain structure. ► Cryogenic cooling of welds generates about 45% grain refinement in welds. ► Phase structure of welds is not affected by flow rates of cryogenic liquid. ► Hardness profile in cryogenically cooled and conventional welds is similar. - Abstract: The energy input and heat dissipation dynamics during fusion welding generates coarse grain in the welds resulting in poor mechanical properties. While grain refinement in welds via the control of the energy input is quite common, the influence of heat dissipation on grain morphology and properties is not fully established. This paper characterized cryogenically cooled ferritic stainless steel (FSS) welds in terms of grain structure and hardness distribution along transverse and thickness directions. Cryogenic cooling reduces the weld dimension by more than 30% and provides grain refinement of almost 45% compared to conventional weld. The hardness distribution in the thickness direction gives slightly higher profile because of decreased grain growth caused by faster cooling effects of cryogenic liquid

Optimizing refiner operation with statistical modelling

Energy Technology Data Exchange (ETDEWEB)

Broderick, G [Noranda Research Centre, Pointe Claire, PQ (Canada)

1997-02-01

The impact of refining conditions on the energy efficiency of the process and on the handsheet quality of a chemi-mechanical pulp was studied as part of a series of pilot scale refining trials. Statistical models of refiner performance were constructed from these results and non-linear optimization of process conditions were conducted. Optimization results indicated that increasing the ratio of specific energy applied in the first stage led to a reduction of some 15 per cent in the total energy requirement. The strategy can also be used to obtain significant increases in pulp quality for a given energy input. 20 refs., 6 tabs.

Guidelines regarding the Review Process under the Convention on Nuclear Safety

International Nuclear Information System (INIS)

2011-01-01

These guidelines, established by the Contracting Parties pursuant to Article 22 of the Convention, are intended to be read in conjunction with the text of the Convention. Their purpose is to provide guidance to the Contracting Parties on the process for reviewing National Reports submitted in accordance with Article 5 and thereby to facilitate the efficient review of implementation by the Contracting Parties of their obligations under the Convention. The aim of the review process should be to achieve a thorough examination of National Reports submitted in accordance with Article 5 of the Convention, so that Contracting Parties can learn from each other's solutions to common and individual nuclear safety problems and, above all, contribute to improving nuclear safety worldwide through a constructive exchange of views [fr

Guidelines regarding the review process under the Convention on Nuclear Safety

International Nuclear Information System (INIS)

2002-01-01

These guidelines, established by the Contracting Parties pursuant to Article 22 of the Convention, are intended to be read in conjunction with the text of the Convention. Their purpose is to provide guidance to the Contracting Parties on the process for reviewing National Reports submitted in accordance with Article 5 and thereby to facilitate the efficient review of implementation by the Contracting Parties of their obligations under the Convention. The aim of the review process should be to achieve a thorough examination of National Reports submitted in accordance with Article 5 of the Convention, so that Contracting Parties can learn from each other's solutions to common and individual nuclear safety problems and, above all, contribute to improving nuclear safety worldwide through a constructive exchange of views

Guidelines regarding the review process under the convention on nuclear safety

International Nuclear Information System (INIS)

1998-01-01

These guidelines, established by the Contracting Parties pursuant to Article 22 of the Convention, are intended to be read in conjunction with the text of the Convention. Their purpose is to provide guidance to the Contracting Parties on the process for reviewing national reports submitted in accordance with Article 5 and thereby to facilitate the efficient review of implementation by the Contracting Parties of their obligations under the Convention. The aim of the review process should be to achieve a thorough examination of national reports submitted in accordance with Article 5 of the Convention, so that Contracting Parties can learn from each other's solutions to common and individual nuclear safety problems and, above all, contribute to improving nuclear safety worldwide through a constructive exchange of views

Guidelines regarding the Review Process under the Convention on Nuclear Safety

International Nuclear Information System (INIS)

2011-01-01

These guidelines, established by the Contracting Parties pursuant to Article 22 of the Convention, are intended to be read in conjunction with the text of the Convention. Their purpose is to provide guidance to the Contracting Parties on the process for reviewing National Reports submitted in accordance with Article 5 and thereby to facilitate the efficient review of implementation by the Contracting Parties of their obligations under the Convention. The aim of the review process should be to achieve a thorough examination of National Reports submitted in accordance with Article 5 of the Convention, so that Contracting Parties can learn from each other's solutions to common and individual nuclear safety problems and, above all, contribute to improving nuclear safety worldwide through a constructive exchange of views

Guidelines regarding the review process under the Convention on Nuclear Safety

International Nuclear Information System (INIS)

1999-01-01

These guidelines, established by the Contracting Parties pursuant to Article 22 of the Convention, are intended to be read in conjunction with the text of the Convention. Their purpose is to provide guidance to the Contracting Parties on the process for reviewing national reports submitted in accordance with Article 5 and thereby to facilitate the efficient review of implementation by the Contracting Parties of their obligations under the Convention. The aim of the review process should be to achieve a thorough examination of national reports submitted in accordance with Article 5 of the Convention, so that Contracting Parties can learn from each other's solutions to common and individual nuclear safety problems and, above all, contribute to improving nuclear safety worldwide through a constructive exchange of views

Guidelines regarding the Review Process under the Convention on Nuclear Safety

International Nuclear Information System (INIS)

2011-01-01

These guidelines, established by the Contracting Parties pursuant to Article 22 of the Convention, are intended to be read in conjunction with the text of the Convention. Their purpose is to provide guidance to the Contracting Parties on the process for reviewing National Reports submitted in accordance with Article 5 and thereby to facilitate the efficient review of implementation by the Contracting Parties of their obligations under the Convention. The aim of the review process should be to achieve a thorough examination of National Reports submitted in accordance with Article 5 of the Convention, so that Contracting Parties can learn from each other's solutions to common and individual nuclear safety problems and, above all, contribute to improving nuclear safety worldwide through a constructive exchange of views [es

Indian refining industry

International Nuclear Information System (INIS)

Singh, I.J.

2002-01-01

The author discusses the history of the Indian refining industry and ongoing developments under the headings: the present state; refinery configuration; Indian capabilities for refinery projects; and reforms in the refining industry. Tables lists India's petroleum refineries giving location and capacity; new refinery projects together with location and capacity; and expansion projects of Indian petroleum refineries. The Indian refinery industry has undergone substantial expansion as well as technological changes over the past years. There has been progressive technology upgrading, energy efficiency, better environmental control and improved capacity utilisation. Major reform processes have been set in motion by the government of India: converting the refining industry from a centrally controlled public sector dominated industry to a delicensed regime in a competitive market economy with the introduction of a liberal exploration policy; dismantling the administered price mechanism; and a 25 year hydrocarbon vision. (UK)

Refining the Enrolment Process in Emergency Medicine Research.

Science.gov (United States)

Sahan, Kate M; Channon, Keith M; Choudhury, Robin P; Kharbanda, Rajesh K; Lee, Regent; Sheehan, Mark

2016-04-01

Research in the emergency setting involving patients with acute clinical conditions is needed if there are to be advances in diagnosis and treatment. But research in these areas poses ethical and practical challenges. One of these is the general inability to obtain informed consent due to the patient's lack of mental capacity and insufficient time to contact legal representatives. Regulatory frameworks which allow this research to proceed with a consent 'waiver', provided patients lack mental capacity, miss important ethical subtleties. One of these is the varying nature of mental capacity among emergency medicine patients. Not only is their capacity variable and often unclear, but some patients are also likely to be able to engage with the researcher and the context to varying degrees. In this paper we describe the key elements of a novel enrolment process for emergency medicine research that refines the consent waiver and fully engages with the ethical rationale for consent and, in this context, its waiver. The process is verbal but independently documented during the 'emergent' stages of the research. It provides appropriate engagement with the patient, is context-sensitive and better addresses ethical subtleties. In line with regulation, full written consent for on-going participation in the research is obtained once the emergency is passed.

Effect of strontium on the grain refining efficiency of Mg-3Al alloy refined by carbon inoculation

International Nuclear Information System (INIS)

Du Jun; Yang Jian; Kuwabara, Mamoru; Li Wenfang; Peng Jihua

2009-01-01

The effect of Sr on the grain refining efficiency of the Mg-3Al alloy refined by carbon inoculation has been investigated in the present study. A significant grain refinement was obtained for the Mg-3Al alloy treated with either 0.2% C or 0.2% Sr. The Al-C-O particles were found in the sample refined by 0.2% C, and the element O should come from reaction between Al 4 C 3 nuclei of Mg grains and water during the process of sample preparation. The grain size of the sample refined by carbon inoculation was further decreased after the combined addition of Sr. The grain size decreased with increasing Sr content. Much higher refining efficiency was obtained when the Sr addition was increased to 0.5%. Sr is an effective element to improve the grain refining efficiency for the Mg-Al alloys refined by carbon inoculation. The number of Al 4 C 3 particles in the sample refined by the combination of carbon and Sr was more than that in the sample refined by only carbon. No Al-C-O-Sr-rich particles were obviously found in the sample refined by the combination of carbon and a little (<0.5%) Sr addition

40 CFR 80.1347 - What are the sampling and testing requirements for refiners and importers?

Science.gov (United States)

2010-07-01

... reformulated or conventional gasoline or RBOB to produce conventional gasoline at a refinery, must exclude the... refinery and the volume and benzene content of gasoline produced at the refinery, and use the compliance... previously certified gasoline that is used to produce conventional gasoline the refiner must include the...

Grain refinement of zinc-aluminium alloys

International Nuclear Information System (INIS)

Zaid, A.I.O.

2006-01-01

It is now well-established that the structure of the zinc-aluminum die casting alloys can be modified by the binary Al-Ti or the ternary Al-Ti-B master alloys. in this paper, grain refinement of zinc-aluminum alloys by rare earth materials is reviewed and discussed. The importance of grain refining of these alloys and parameters affecting it are presented and discussed. These include parameters related to the Zn-Al alloys cast, parameters related to the grain refining elements or alloys and parameters related to the process. The effect of addition of other alloying elements e.g. Zr either alone or in the presence of the main grain refiners Ti or Ti + B on the grain refining efficiency is also reviewed and discussed. Furthermore, based on the grain refinement and the parameters affecting it, a criterion for selection of the optimum grain refiner is suggested. Finally, the recent research work on the effect of grain refiners on the mechanical behaviour, impact strength, wear resistance, and fatigue life of these alloys are presented and discussed. (author)

Applications of Enzymes in Oil and Oilseed Processing

DEFF Research Database (Denmark)

Xu, Xuebing

Enzymes, through the last 20-30 years research and development, have been widely explored for the uses in oil and oilseed processing. Following the conventional processing technology from oilseeds, the oil can be produced through pressing or solvent extraction. The crude oil is then refined to meet...... edible requirements. The oil can be also modified to meet functional or even nutritional needs. In each of those steps, enzymes have been used in industry successfully. For the oil processing stage, enzymes have been used to destroy the cell structure so that makes the oil release easier, where...... conventionally high temperature conditioning or cooking is necessary. The good story in industry is the fish oil and olive oil processing. Good quality and higher oil yield have been achieved through the use of enzymes in the processing stages. For the refining stage, the use of enzymes for degumming has...

Metal decontamination for waste minimization using liquid metal refining technology

International Nuclear Information System (INIS)

Joyce, E.L. Jr.; Lally, B.; Ozturk, B.; Fruehan, R.J.

1993-01-01

The current Department of Energy Mixed Waste Treatment Project flowsheet indicates that no conventional technology, other than surface decontamination, exists for metal processing. Current Department of Energy guidelines require retrievable storage of all metallic wastes containing transuranic elements above a certain concentration. This project is in support of the National Mixed Low Level Waste Treatment Program. Because of the high cost of disposal, it is important to develop an effective decontamination and volume reduction method for low-level contaminated metals. It is important to be able to decontaminate complex shapes where surfaces are hidden or inaccessible to surface decontamination processes and destruction of organic contamination. These goals can be achieved by adapting commercial metal refining processes to handle radioactive and organic contaminated metal. The radioactive components are concentrated in the slag, which is subsequently vitrified; hazardous organics are destroyed by the intense heat of the bath. The metal, after having been melted and purified, could be recycled for use within the DOE complex. In this project, we evaluated current state-of-the-art technologies for metal refining, with special reference to the removal of radioactive contaminants and the destruction of hazardous organics. This evaluation was based on literature reports, industrial experience, plant visits, thermodynamic calculations, and engineering aspects of the various processes. The key issues addressed included radioactive partitioning between the metal and slag phases, minimization of secondary wastes, operability of the process subject to widely varying feed chemistry, and the ability to seal the candidate process to prevent the release of hazardous species

Beyond Texas City: the state of process safety in the unionized U.S. oil refining industry.

Science.gov (United States)

McQuiston, Thomas H; Lippin, Tobi Mae; Bradley-Bull, Kristin; Anderson, Joseph; Beach, Josie; Beevers, Gary; Frederick, Randy J; Frederick, James; Greene, Tammy; Hoffman, Thomas; Lefton, James; Nibarger, Kim; Renner, Paul; Ricks, Brian; Seymour, Thomas; Taylor, Ren; Wright, Mike

2009-01-01

The March 2005 British Petroleum (BP) Texas City Refinery disaster provided a stimulus to examine the state of process safety in the U.S. refining industry. Participatory action researchers conducted a nation-wide mail-back survey of United Steelworkers local unions and collected data from 51 unionized refineries. The study examined the prevalence of highly hazardous conditions key to the Texas City disaster, refinery actions to address those conditions, emergency preparedness and response, process safety systems, and worker training. Findings indicate that the key highly hazardous conditions were pervasive and often resulted in incidents or near-misses. Respondents reported worker training was insufficient and less than a third characterized their refineries as very prepared to respond safely to a hazardous materials emergency. The authors conclude that the potential for future disasters plagues the refining industry. In response, they call for effective proactive OSHA regulation and outline ten urgent and critical actions to improve refinery process safety.

pH-zone-refining elution-extrusion countercurrent chromatography: Separation of hydroxyanthraquinones from Cassiae semen.

Science.gov (United States)

Bu, Zhisi; Lv, Liqiong; Li, Xingnuo; Chu, Chu; Tong, Shengqiang

2017-11-01

Seven hydroxyanthraquinones were successfully separated from the traditional Chinese medicinal herb Cassiae semen by conventional and pH-zone-refining countercurrent chromatography with an environmentally friendly biphasic solvent system, in which elution-extrusion mode was investigated for pH-zone-refining countercurrent chromatography for the first time. A two-phase solvent system composed of n-hexane/ethyl acetate/ethanol/water (5:3:4:4, v/v/v/v) was used for the conventional countercurrent chromatography while the same system with a different volume ratio n-hexane/ethyl acetate/ethanol/water (3:5:2:6, v/v/v/v) was used for pH-zone-refining countercurrent chromatography, in which 20 mmol/L of trifluoroacetic acid was added in the organic phase as a retainer and 15 mmol/L of ammonia was added to the aqueous phase as an eluter. A 400 mg crude sample could be well separated by pH-zone-refining countercurrent chromatography, yielding 53 mg of aurantio-obtusin, 40 mg of chryso-obtusin, 18 mg of obtusin, 24 mg of obtusifolin, 10 mg of emodin, and 105 mg of the mixture of chrysophanol and physcion with a purity of over 95.8, 95.7, 96.9, 93.5, 97.4, 77.1, and 19.8%, as determined by high-performance liquid chromatography. Furthermore, the difference in elution sequence between conventional and pH-zone-refining mode was observed and discussed. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Future refining impacts of the Clean Air Act amendments of 1990

International Nuclear Information System (INIS)

Hadder, G.R.

1992-01-01

An assessment of the future refining impacts of the U.S. Clean Air Act Amendments of 1990 has been performed with the Navy Mobility Fuels Forecasting System. In 1992, the Environmental Protection Agency (EPA) should finalize precise requirements for Phase I reformulated gasoline, to be produced in 1995-1999. EPA requirements for Phase II reformulated gasoline, to be produced after 1999, will not be established until 1993. The assessment of refining impacts assumes that reformulated gasoline with likely Phase I specifications will be produced for markets projected for the year 2000. The assessment suggests that gasoline reformulation costs in U.S. coastal and near-coastal refining regions could be 3.5 to 5.6 cents per gallon (1989 U.S. currency). The relative value of MTBE is the most important determinant of the reformulation cost. For mileage equivalent to one gallon of conventional gasoline, the regional total added costs (including reformulation costs) for reformulated gasoline could be 5.2 to 7.6 cents. In blending reformulated gasolines, the reduction of butane for lower Reid vapor pressure and the reduction of reformate for lower aromatics are generally compensated by increased percentages of alkylate and/or straight run naphthas. Relatively larger refinery process capacity additions are required for butane isomerization alkylation aromatics recovery, and distillate hydrotreating. (Author)

Grain Refinement of Permanent Mold Cast Copper Base Alloys

Energy Technology Data Exchange (ETDEWEB)

M.Sadayappan; J.P.Thomson; M.Elboujdaini; G.Ping Gu; M. Sahoo

2005-04-01

Grain refinement is a well established process for many cast and wrought alloys. The mechanical properties of various alloys could be enhanced by reducing the grain size. Refinement is also known to improve casting characteristics such as fluidity and hot tearing. Grain refinement of copper-base alloys is not widely used, especially in sand casting process. However, in permanent mold casting of copper alloys it is now common to use grain refinement to counteract the problem of severe hot tearing which also improves the pressure tightness of plumbing components. The mechanism of grain refinement in copper-base alloys is not well understood. The issues to be studied include the effect of minor alloy additions on the microstructure, their interaction with the grain refiner, effect of cooling rate, and loss of grain refinement (fading). In this investigation, efforts were made to explore and understand grain refinement of copper alloys, especially in permanent mold casting conditions.

Effect of Cellulases and Xylanases on Refining Process and Kraft Pulp Properties.

Directory of Open Access Journals (Sweden)

Kamila Przybysz Buzała

Full Text Available Samples of bleached kraft pine cellulosic pulp, either treated with an enzyme preparation (a Thermomyces lanuginosus xylanase, an Aspergillus sp. cellulase, and a multienzyme preparation NS-22086 containing both these activities or untreated, were refined in a laboratory PFI mill. The treatment with cellulases contained in the last two preparations significantly improved the pulp's susceptibility to refining (the target freeness value of 30°SR was achieved in a significantly shorter time, increased water retention value (WRV and fines contents while the weighted average fiber length was significantly reduced. These changes of pulp parameters caused deterioration of paper strength properties. The treatment with the xylanase, which partially hydrolyzed xylan, small amounts of which are associated with cellulose fibers, only slightly loosened the structure of fibers. These subtle changes positively affected the susceptibility of the pulp to refining (refining energy was significantly reduced and improved the static strength properties of paper. Thus, the treatment of kraft pulps with xylanases may lead to substantial savings of refining energy without negative effects on paper characteristics.

Anaerobic digestion of residues from production and refining of vegetable oils as an alternative to conventional solutions.

Science.gov (United States)

Torrijos, M; Thalla, Arun Kumar; Sousbie, P; Bosque, F; Delgenès, J P

2008-01-01

The purpose of this work was to study the anaerobic digestion of by-products generated during the production and refining of oil with the objective of proposing an alternative solution (methanisation) to the conventional solutions while reducing the energy consumption of fossil origin on refinery sites. The production of sunflower oil was taken as example. Glycerine from the production of biodiesel was also included in this study. The results show that glycerine has a high potential for methanisation because of its high methane potential (465 ml CH4/g VS) and high metabolization rates (0.42 g VS/g VSS.d). The use of oil cake as substrate for anaerobic digestion is not interesting because it has a low methane potential of 215 ml CH4/g VS only and because it is easily recovered in animal feed. Six residues have quite a high methane potential (465 to 850 ml CH4/g VS) indicating a good potential for anaerobic digestion. However, they contain a mixture of rapidly and slowly biodegradable organic matter and the loading rates must remain quite low (0.03 to 0.09 g VS/g VSS.d) to prevent any accumulation of slowly biodegradable solids in the digesters. IWA Publishing 2008.

Region-of-interest volumetric visual hull refinement

KAUST Repository

Knoblauch, Daniel; Kuester, Falko

2010-01-01

This paper introduces a region-of-interest visual hull refinement technique, based on flexible voxel grids for volumetric visual hull reconstructions. Region-of-interest refinement is based on a multipass process, beginning with a focussed visual

Towards automated crystallographic structure refinement with phenix.refine

OpenAIRE

Afonine, Pavel V.; Grosse-Kunstleve, Ralf W.; Echols, Nathaniel; Headd, Jeffrey J.; Moriarty, Nigel W.; Mustyakimov, Marat; Terwilliger, Thomas C.; Urzhumtsev, Alexandre; Zwart, Peter H.; Adams, Paul D.

2012-01-01

phenix.refine is a program within the PHENIX package that supports crystallographic structure refinement against experimental data with a wide range of upper resolution limits using a large repertoire of model parameterizations. It has several automation features and is also highly flexible. Several hundred parameters enable extensive customizations for complex use cases. Multiple user-defined refinement strategies can be applied to specific parts of the model in a single refinement run. An i...

Role and distribution of strontium during the dissolving and grain refining process of AlSi7Mg alloy's structure

Energy Technology Data Exchange (ETDEWEB)

Moldovan, P.; Popescu, G.; Zsigmond, M.; Apostolescu, I. [Universitatea Politehnica, Bucharest (Romania)

2002-07-01

The aim of this paper is the study of the modification of AlSi7Mg alloy with two types of master alloys: AlSr10 wire type and AlSr10 block type, at a temperature of 750 C with different contents of strontium. Due to the applicability of the AlSr10 master alloy wire type, the study was mainly elaborated on the dissolving process of this one. Due to this fact we used a 10 mm diameter wire of AlSr10 master alloy, which was introduced in the melt. After the grain refining process we obtained a sample, which was cut at different heights for a better observation of the alloy structure. We can notice that the grain refining degree is not uniform along the sample. Strontium as a grain refiner equalize the qualities of sodium but is much more efficient and keeps its grain refining properties for a longer period of time. The efficiency of the two types of master alloys was compared by the grain refinement degree of AlSi7Mg alloy function of the distance till the lower part of the casting mould and by determination of the grain refinement degree function of strontium content added. We made a micrographic study of the pieces of the sample and we used an optical microscope (OLYMPUS BX 60M) and the image analyzing system was OMNIMENT EXPRESS. Analyzing the results of this study we can see that the AlSi7Mg alloy grain refining degree doesn't depend too much on the form of the master alloy (if is wire or block) but grain refining time is increased when we use block types of master alloy. Also we can see that the cooling rate has a significant influence on the grain refinement degree. The industrial application of the AlSr master alloys are mainly for the light alloys ingots producers and light alloys casting plant for the obtaining of high quality components required by automotive and aeronautical industry. (orig.)

The Analysis of the Chloride and Fluoride Influences on the Reducer Refinement Processes (Carbo-N-Ox Aluminum Alloys

Directory of Open Access Journals (Sweden)

Bydałek A. W.

2013-09-01

Full Text Available Slag refining slag with west materials was analysed used the DTA methods. In the paper a method of determining the reduction capability, with the Carbo-N-Ox method, of slag solutions was used. Some relations between the stimulators in the environment - slag - metal system allow to initiate mass exchange reactions in the process of slag refining.The presented in work course of behaviour permits on choice of basic composition of slaglite, the of necessary components stimulating quantities, as well as on accomplishment of opinion of ability refinement. The worked out programme Slag-Prop, after introduction of data with experiment, it allows on next corrections in composition of proposed mixtures also, should be put on properly elaborated factors of multistage reaction with essential usage of suitable stimulators.

Preliminary assessment of future refining impacts of the Clean Air Act Amendments of 1990

International Nuclear Information System (INIS)

Hadder, G.R.

1991-09-01

A preliminary assessment of the future refining impacts of the Clean Air Act Amendments of 1990 has been performed with the Navy Mobility Fuels Forecasting Systems. The assessment suggests that gasoline reformulation costs in domestic coastal and near-coastal refining regions in the year 2000 could be 3.5 to 5.6 cents per gallon (in terms of 1989 currency). For heating value equivalent to one gallon of conventional gasoline, the regional total added costs (including reformulation costs) for reformulated gasoline could be 5.9 to 8.0 cents. In blending reformulated gasolines, the reduction of butane for lower Reid vapor pressure and the reduction of reformate for lower aromatics are generally compensated by increased percentages of alkylate and/or straight run naphthas. Relatively larger refinery process capacity additions are required for butane isomerization, alkylation, aromatics recovery, and distillate hydrotreating. 21 refs., 3 figs., 18 tabs

Cavitation-aided grain refinement in aluminium alloys

NARCIS (Netherlands)

Atamanenko, T.V.

2010-01-01

This thesis deals with grain refinement under the influence of ultrasonic-driven cavitation in aluminium casting processes. Three major goals of this research were: (1) to identify the mechanism of the cavitation-aided grain refinement at different stages of solidification; (2) to reveal the

Effect of Refining Processes on Magnitude and Nature of Malathion and Carbofuran Residues in Cotton Seed Oil

International Nuclear Information System (INIS)

Zayed, S.M.A.D.; Farghaly, M.; Mahdy, F.

2005-01-01

Cotton seeds obtained from 14 C-carbofuran or 14 C-malathion-treated plants contained 0.25% and 0.11% of the originally applied radioactivity, respectively. The concentration of malathion residues in oil, methanol soluble and in the seed cake amounted to 0.94, 2.6 and 1.7 ppm, respectively. Commercial processing procedures led to a gradual decrease in the total amount of 14 C-residues in oils with aged residues as well as in oil fortified with the radiolabelled insecticides. The refined oil contained only about 20% of the 14 C-residues originally present. The major residue in processed oil contained malathion, malathion monocarboxylic acid and alpha-(O,O-dimethyl phosphorodithio)-propionic acid. The concentration of 14 C-carbofuran residues in cotton seed oil, methanol extract and cake was 1.7, 12.3 and 2.4 ppm, respectively. The main residues in the oil were carbofuran and its phenol. The methanol solubles contained conjugated metabolites, which upon hydrolysis gave 3-hydroxy-carbofuran as a major product. Refinement reduced the residue in oil to 0.26 ppm. The residue in refined oil contained carbofuran and carbofuran phenol as main constituents together with smaller amounts of 3-hydroxy- and 3-keto carbofuran

Pilot scale refinning of crude soybean oil | Mensah | Journal of ...

African Journals Online (AJOL)

Pilot scale refinning of crude soybean oil. ... Abstract. A laboratory process for refining soybean has been scaled up to a 145 tonne per annum pilot plant to refine crude soybean oil. ... The quality of the refined oil was found to be within national and codex standard specifications for edible oil from vegetable sources.

Carcinogenicity of petroleum lubricating oil distillates: effects of solvent refining, hydroprocessing, and blending.

Science.gov (United States)

Halder, C A; Warne, T M; Little, R Q; Garvin, P J

1984-01-01

Certain refining processes were investigated to determine their influence on the dermal carcinogenic activity of petroleum-derived lubricating oil distillates. Specifically, the effects of solvent refining, hydroprocessing, a combination of both processes, and the blending of oils processed using each technique were evaluated in standard mouse skin-painting bioassays. The refining process used as well as the level or severity of treatment greatly influenced the carcinogenic outcome of processed lubricating oils. Solvent refining at severities normally used appeared to eliminate carcinogenicity. In contrast, hydroprocessing alone at mild levels of treatment was successful only in reducing the carcinogenic potency; severe hydroprocessing conditions were necessary to eliminate carcinogenic activity without the use of additional refining processes. Carcinogenic activity could also be eliminated by following moderate solvent refining with mild hydroprocessing. Blending of hydroprocessed oils with solvent-refined oils resulted in a substantial reduction or even elimination of carcinogenic activity. However, the degree of protection obtained varied with the particular distillates used and appeared largely dependent on the inherent biological activity of the hydroprocessed oil.

All-solution-processed organic solar cells with conventional architecture

NARCIS (Netherlands)

Franeker, J.J. van; Voorthuijzen, W.P.; Gorter, H.; Hendriks, K.H.; Janssen, R.A.J.; Hadipour, A.; Andriessen, H.A.J.M.; Galagan, Y.O.

2013-01-01

Abstract All-solution processed organic solar cells with a conventional device structure were demonstrated. The evaporated low work function LiF/Al electrode was replaced by a printed high work function silver electrode combined with an additional electron transport layer (ETL). Two electron

The role of ultrasonic cavitation in refining the microstructure of aluminum based nanocomposites during the solidification process.

Science.gov (United States)

Xuan, Yang; Nastac, Laurentiu

2018-02-01

Recent studies showed that the microstructure and mechanical properties of aluminum based nanocomposites can be significantly improved when ultrasonic cavitation and solidification processing is used. This is because ultrasonic cavitation processing plays an important role not only in degassing and dispersion of the nanoparticles, but also in breaking up the dendritic grains and refining the as-cast microstructure. In the present study, A356 alloy and Al 2 O 3 nanoparticles are used as the matrix alloy and the reinforcement, respectively. Nanoparticles were added into the molten A356 alloy and dispersed via ultrasonic cavitation processing. Ultrasonic cavitation was applied over various temperature ranges during molten alloy cooling and solidification to investigate the grain structure formation and the nanoparticle dispersion behavior. Optical Microscopy and Scanning Electron Microscopy were used to investigate in detail the differences in the microstructure characteristics and the nanoparticle distribution. Experimental results indicated that the ultrasonic cavitation processing and Al 2 O 3 nanoparticles play an important role for microstructure refinement. In addition, it was shown in this study that the Al 2 O 3 nanoparticles modified the eutectic phase. Copyright © 2017 Elsevier B.V. All rights reserved.

Microstructural examination by TEM of WC/Co composites prepared by conventional and Microwave processes

International Nuclear Information System (INIS)

Agrawal, D.; Cheng, J.; Papworth, A.J.; Jain, H.; Williams, D.B.

2001-01-01

Recently, significant developments and advances have taken place in the field of microwave processing of ceramics, composites and metals. Microwave sintering technology of WC/Co based hard metal parts has been now developed for commercial products. Microwave processed WC/Co parts reportedly have exhibited superior performance over standard parts. Additionally, the microwave process requires only one tenth of the total cycle time employed in a conventional process. Laboratory corrosion and impact resistance tests have proved that microwave processed WC/Co parts are several times more resistant than the conventional parts of the same composition. The scanning transmission electron microscopic (STEM) examination conducted an conventionally and microwave sintered WC/Co samples exhibited remarkable difference in the chemistry of cobalt binder phase. It is understood that the superior mechanical properties of microwave sintered part are due to the pure cobalt phase present at the grain boundary of WC grains, while the conventionally sintered part showed there was substantial inter-alloying of Co with tungsten. (author)

The Ad Hoc process to strengthen the framework convention on climate change

Energy Technology Data Exchange (ETDEWEB)

Ramakrishna, K.; Deutz, A.M.; Jacobsen, L.A. [eds.

1995-11-01

The Woods Hole Research Center convened an International Conference on The Ad Hoc Process to Strengthen the Framework Convention on Climate Change in Woods Hole, MA, on October 7-9, 1995. The conference was conducted to examine the prospects for successful adoption of a protocol to the Framework Convention on Climate Change by 1997. In preparation for the Second session of the Ad Hoc Group on the Berlin Mandate, several governmental and nongovernmental representatives met in Woods Hole to discuss the process and possible outcome of the Berlin Mandate negotiations for a protocol or other legal instrument to strengthen the Convention. The conference was by invitation and all participants attended in their personal capacities.

Numerical analysis of impurity separation from waste salt by investigating the change of concentration at the interface during zone refining process

Science.gov (United States)

Choi, Ho-Gil; Shim, Moonsoo; Lee, Jong-Hyeon; Yi, Kyung-Woo

2017-09-01

The waste salt treatment process is required for the reuse of purified salts, and for the disposal of the fission products contained in waste salt during pyroprocessing. As an alternative to existing fission product separation methods, the horizontal zone refining process is used in this study for the purification of waste salt. In order to evaluate the purification ability of the process, three-dimensional simulation is conducted, considering heat transfer, melt flow, and mass transfer. Impurity distributions and decontamination factors are calculated as a function of the heater traverse rate, by applying a subroutine and the equilibrium segregation coefficient derived from the effective segregation coefficients. For multipass cases, 1d solutions and the effective segregation coefficient obtained from three-dimensional simulation are used. In the present study, the topic is not dealing with crystal growth, but the numerical technique used is nearly the same since the zone refining technique was just introduced in the treatment of waste salt from nuclear power industry because of its merit of simplicity and refining ability. So this study can show a new application of single crystal growth techniques to other fields, by taking advantage of the zone refining multipass possibility. The final goal is to achieve the same high degree of decontamination in the waste salt as in zone freezing (or reverse Bridgman) method.

All-solution-processed organic solar cells with conventional architecture

NARCIS (Netherlands)

Franeker, van J.J.; Voorthuijzen, W.P.; Gorter, H.; Hendriks, K.H.; Janssen, R.A.J.; Hadipour, A.; Andriessen, R.; Galagan, Y.

2013-01-01

All-solution processed organic solar cells with a conventional device structure were demonstrated. The evaporated low work function LiF/Al electrode was replaced by a printed high work function silver electrode combined with an additional electron transport layer (ETL). Two electron transport layers

Directions in refining and upgrading of heavy oil and bitumen

International Nuclear Information System (INIS)

Dawson, B.; Parker, R. J.; Flint, L.

1997-01-01

The expansion of heavy oil transportation, marketing and refining facilities over the past two decades have been reviewed to show the strides that several Canadian refiners have taken to build up the facilities required to process synthetic crude oil (SCO). Key points made at a conference, convened by the National Centre for Upgrading Technology (NCUT), held in Edmonton during September 1997 to discuss current and future directions in the refining and marketing of heavy oil, bitumen and SCO, were summarized. Among the key points mentioned were: (1) the high entry barriers faced by centralized upgraders, (2) the advantages of integrating SCO or heavy oil production with downstream refining, (3) the stiff competition from Venezuela and Mexico that both SCO and heavy oil will face in the U.S. PADD II market, (4) the differences between Canadian refiners who have profited from hydrocracking and are better able to handle coker-based SCO, and American refiners who rely chiefly on catalytic cracking and are less able to process the highly aromatic SCO, and (5) the disproportionate cost in the upgrading process represented by the conversion of asphaltenes. Challenges and opportunities for key stakeholders, i.e. producers, refiners, marketers and technology licensors also received much attention at the Edmonton conference

Parallel Block Structured Adaptive Mesh Refinement on Graphics Processing Units

Energy Technology Data Exchange (ETDEWEB)

Beckingsale, D. A. [Atomic Weapons Establishment (AWE), Aldermaston (United Kingdom); Gaudin, W. P. [Atomic Weapons Establishment (AWE), Aldermaston (United Kingdom); Hornung, R. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gunney, B. T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gamblin, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Herdman, J. A. [Atomic Weapons Establishment (AWE), Aldermaston (United Kingdom); Jarvis, S. A. [Atomic Weapons Establishment (AWE), Aldermaston (United Kingdom)

2014-11-17

Block-structured adaptive mesh refinement is a technique that can be used when solving partial differential equations to reduce the number of zones necessary to achieve the required accuracy in areas of interest. These areas (shock fronts, material interfaces, etc.) are recursively covered with finer mesh patches that are grouped into a hierarchy of refinement levels. Despite the potential for large savings in computational requirements and memory usage without a corresponding reduction in accuracy, AMR adds overhead in managing the mesh hierarchy, adding complex communication and data movement requirements to a simulation. In this paper, we describe the design and implementation of a native GPU-based AMR library, including: the classes used to manage data on a mesh patch, the routines used for transferring data between GPUs on different nodes, and the data-parallel operators developed to coarsen and refine mesh data. We validate the performance and accuracy of our implementation using three test problems and two architectures: an eight-node cluster, and over four thousand nodes of Oak Ridge National Laboratory’s Titan supercomputer. Our GPU-based AMR hydrodynamics code performs up to 4.87× faster than the CPU-based implementation, and has been scaled to over four thousand GPUs using a combination of MPI and CUDA.

Disparity refinement process based on RANSAC plane fitting for ...

African Journals Online (AJOL)

... more accurate than normal flow state-of-the-art stereo matching algorithms. The performance evaluations are based on standard image quality metrics i.e. structural similarity index measure, peak signal-to-noise ratio and mean square error. Keywords: computer vision; disparity refinement; image segmentation; RANSAC; ...

Effects of die profile on grain refinement in Al–Mg alloy processed by repetitive corrugation and straightening

Energy Technology Data Exchange (ETDEWEB)

Thangapandian, N., E-mail: erpandian@gmail.com [Department of Mechanical Engineering, College of Engineering Guindy, Anna University, Chennai 600025 (India); Balasivanandha Prabu, S. [Department of Mechanical Engineering, College of Engineering Guindy, Anna University, Chennai 600025 (India); Padmanabhan, K.A. [Centre for Nanotechnology, University of Hyderabad, Hyderabad 500046 (India)

2016-01-01

It is shown that a proper selection of corrugation die profile and die parameters is essential for achieving homogeneous grain refinement in materials subjected to repetitive corrugation and straightening (RCS). An Al–Mg (AA 5083) alloy was subjected to the RCS process using three different corrugation die profiles (V-groove, Flat groove, and Semi-circular groove), followed by straightening to determine the allowable maximum number of passes prior to surface cracking/fracture. Mechanical properties, i.e., hardness and tensile strength of the RCS samples were measured and compared as functions of corrugation die profiles and number of passes and the changes in microstructure. Grain refinement was studied using Electron Back Scattered Diffraction (EBSD) analysis and Transmission Electron Microscopy (TEM).

Kolmogorov's refined similarity hypotheses for turbulence and general stochastic processes

International Nuclear Information System (INIS)

Stolovitzky, G.; Sreenivasan, K.R.

1994-01-01

Kolmogorov's refined similarity hypotheses are shown to hold true for a variety of stochastic processes besides high-Reynolds-number turbulent flows, for which they were originally proposed. In particular, just as hypothesized for turbulence, there exists a variable V whose probability density function attains a universal form. Analytical expressions for the probability density function of V are obtained for Brownian motion as well as for the general case of fractional Brownian motion---the latter under some mild assumptions justified a posteriori. The properties of V for the case of antipersistent fractional Brownian motion with the Hurst exponent of 1/3 are similar in many details to those of high-Reynolds-number turbulence in atmospheric boundary layers a few meters above the ground. The one conspicuous difference between turbulence and the antipersistent fractional Brownian motion is that the latter does not possess the required skewness. Broad implications of these results are discussed

Recovery of Spent Bleaching Earth From Palm Oil Refining Using Radiation

International Nuclear Information System (INIS)

Nor Azillah Fatimah Othman; Tuan Amran Tuan Abdullah; Nor Azillah Fatimah Othman; Nor Azwin Shukri; Selambakkanu, S.; Siti Fatahiyah Mohamad

2014-01-01

Acid activated calcium montmorillonite clay or commonly referred to as bleaching clays is one type of clay used in physical refining of palm oil and it is prioritized in removing a variety of undesirable impurities which would otherwise impart colour, odour and taste to the refined product. Used-up bleaching clays or known as Spent Bleaching Earth (SBE) is considered as industrial waste and commonly dispose without any pretreatment. SBE usually contains considerable quantities of entrained oil that is quantified approximately to 30 to 40 %. The residual oil in these principal solid waste products can rapidly oxidize to the point of spontaneous ignition as a result of clay-catalyzed auto-oxidation reactions. Due to this fact, the disposal of SBE has become an environmental problem and pretreatment of SBE is very important. There are several studies on the residual oil removal from the SBE using heat treatment. Radiation generated from electron beam accelerator can supply high energy to break the C-C and C-H bond. It is expected that the removal of hydrocarbon will occurs at high rate compared to conventional heating. This research proposes the use of radiation on the recovery of SBE from palm oil refining waste. Evaluation of radiation effect on properties of SBE will be conducted to study the effectiveness of using radiation in the purification process. Finally, the material produced will be evaluated and characterized for regeneration and reuse purpose. (author)

The effect of microstructure and texture evolution on mechanical properties of low-carbon steel processed by the continuous hybrid process

International Nuclear Information System (INIS)

Hwang, Sun Kwang; Baek, Hyun Moo; Son, Il-Heon; Im, Yong-Taek; Bae, Chul Min

2013-01-01

In this paper, the continuous hybrid process is newly designed and applied for producing grain-refined long and large cross-section wires of low-carbon steel at high speed at room temperature. The initial specimen, with a diameter of 13 mm, continuously passes through the rolls, equal channel angular pressing (ECAP) dies, and wire-drawing dies in sequence during the process. The specimens deformed by the continuous hybrid process without and with the wire-drawing dies were obtained to investigate the role in the deformation separately. Their microstructures, textures, and mechanical properties were investigated by optical microscopy (OM), electron backscattering diffraction (EBSD), X-ray diffraction (XRD), tension, and Vickers micro-hardness tests and were compared with those for the case processed by the conventional wire-drawing process. According to the present investigation, the continuous hybrid process can more efficiently manufacture fine-grained wires with a strong shear texture in a continuous way than the conventional wire-drawing process can. In addition, the ultimate tensile strength value of the specimen processed by the continuous hybrid process was 23.9% higher, although the elongation was slightly lower than the one produced by the conventional wire-drawing process. The plastic deformation was mainly imposed by the ECAP dies, and the wire-drawing dies improve the dimensional accuracy and increase the local strain homogeneity in the continuous hybrid process. It is demonstrated that the continuous hybrid process might be beneficial in commercializing a continuous application of the severe plastic deformation process for producing grain-refined wires for industrial applications

Post-Processing Approach for Refining Raw Land Cover Change Detection of Very High-Resolution Remote Sensing Images

Directory of Open Access Journals (Sweden)

Zhiyong Lv

2018-03-01

Full Text Available In recent decades, land cover change detection (LCCD using very high-spatial resolution (VHR remote sensing images has been a major research topic. However, VHR remote sensing images usually lead to a large amount of noises in spectra, thereby reducing the reliability of the detected results. To solve this problem, this study proposes an object-based expectation maximization (OBEM post-processing approach for enhancing raw LCCD results. OBEM defines a refinement of the labeling in a detected map to enhance its raw detection accuracies. Current mainstream change detection (preprocessing techniques concentrate on proposing a change magnitude measurement or considering image spatial features to obtain a change detection map. The proposed OBEM approach is a new solution to enhance change detection accuracy by refining the raw result. Post-processing approaches can achieve competitive accuracies to the preprocessing methods, but in a direct and succinct manner. The proposed OBEM post-processing method synthetically considers multi-scale segmentation and expectation maximum algorithms to refine the raw change detection result. Then, the influence of the scale of segmentation on the LCCD accuracy of the proposed OBEM is investigated. Four pairs of remote sensing images, one of two pairs (aerial image with 0.5 m/pixel resolution which depict two landslide sites on Landtau Island, Hong Kong, China, are used in the experiments to evaluate the effectiveness of the proposed approach. In addition, the proposed approach is applied, and validated by two case studies, LCCD in Tianjin City China (SPOT-5 satellite image with 2.5 m/pixel resolution and Mexico forest fire case (Landsat TM images with 30 m/pixel resolution, respectively. Quantitative evaluations show that the proposed OBEM post-processing approach can achieve better performance and higher accuracies than several commonly used preprocessing methods. To the best of the authors’ knowledge, this type

Russian refining - an industry in transition

Energy Technology Data Exchange (ETDEWEB)

Barrett, E [CentreInvest, Moscow (Russian Federation)

1999-02-01

In the old Soviet Union (now called the CIS), the refining industry is undergoing much modernisation, although the process is far from complete. Eventually, the CIS is expected to have a market-responsive competitive refining business. The expected transformation is discussed according to a five-stage plan. The stages are (i) the change from horizontally integrated entity to vertically integrated global concerns, (ii) the change from over-manned dinosaurs to modern efficient businesses, (iii) the move towards smaller, more advanced market-orientated processes, (iv) improving the transport and storage infrastructures and (v) improving accountability and profitability. The predictions for 2005 onwards are for sustained profitability. (UK)

The conventional ammunition requirements determination process of the U.S. Navy.

OpenAIRE

Mawson, John III

1985-01-01

Approved for public release; distribution is unlimited The objective of this thesis is to analyze the Requirements Determination procedures in the Navy's Conventional Gun Ammunition System in an attempt to identify areas for potential improvement. The Conventional Gun Ammunition System involves a logical progression of steps initiated on an annual basis. The Secretary of Defense begins the process by issuing broad guidance for the development of documentation to support b...

A Canadian refiner's perspective of synthetic crudes

International Nuclear Information System (INIS)

Halford, T.L.; McIntosh, A.P.; Rasmussen

1997-01-01

Some of the factors affecting a refiner's choice of crude oil include refinery hardware, particularly gas oil crackers, products slate and product specifications, crude availability, relative crude price and crude quality. An overview of synthetic crude, the use of synthetic crude combined with other crudes and a comparison of synthetic crude with conventional crude oil was given. The two main users of synthetic crude are basically two groups of refiners, those large groups who use synthetic crude combined with other crudes, and a smaller group who run synthetic crude on specially designed units as a sole feed. The effects of changes in fuel legislation were reviewed. It was predicted that the changes will have a mixed impact on the value of synthetic crude, but low sulphur diesel regulations and gasoline sulphur regulations will make current synthetic crudes attractive. The big future change with a negative impact will be diesel cetane increases to reduce engine emissions. This will reduce synthetic crude attractiveness due to distillate yields and quality and high gas oil yields. Similarly, any legislation limiting aromatics in diesel fuel will also make synthetic crudes less attractive. Problems experienced by refiners with hardware dedicated to synthetic crude (salt, naphthenic acid, fouling, quality variations) were also reviewed. 3 tabs

Bauxite Mining and Alumina Refining

Science.gov (United States)

Frisch, Neale; Olney, David

2014-01-01

Objective: To describe bauxite mining and alumina refining processes and to outline the relevant physical, chemical, biological, ergonomic, and psychosocial health risks. Methods: Review article. Results: The most important risks relate to noise, ergonomics, trauma, and caustic soda splashes of the skin/eyes. Other risks of note relate to fatigue, heat, and solar ultraviolet and for some operations tropical diseases, venomous/dangerous animals, and remote locations. Exposures to bauxite dust, alumina dust, and caustic mist in contemporary best-practice bauxite mining and alumina refining operations have not been demonstrated to be associated with clinically significant decrements in lung function. Exposures to bauxite dust and alumina dust at such operations are also not associated with the incidence of cancer. Conclusions: A range of occupational health risks in bauxite mining and alumina refining require the maintenance of effective control measures. PMID:24806720

Refining Lane-Based Traffic Signal Settings to Satisfy Spatial Lane Length Requirements

Directory of Open Access Journals (Sweden)

Yanping Liu

2017-01-01

Full Text Available In conventional lane-based signal optimization models, lane markings guiding road users in making turns are optimized with traffic signal settings in a unified framework to maximize the overall intersection capacity or minimize the total delay. The spatial queue requirements of road lanes should be considered to avoid overdesigns of green durations. Point queue system adopted in the conventional lane-based framework causes overflow in practice. Based on the optimization results from the original lane-based designs, a refinement is proposed to enhance the lane-based settings to ensure that spatial holding limits of the approaching traffic lanes are not exceeded. A solution heuristic is developed to modify the green start times, green durations, and cycle length by considering the vehicle queuing patterns and physical holding capacities along the approaching traffic lanes. To show the effectiveness of this traffic signal refinement, a case study of one of the busiest and most complicated intersections in Hong Kong is given for demonstration. A site survey was conducted to collect existing traffic demand patterns and existing traffic signal settings in peak periods. Results show that the proposed refinement method is effective to ensure that all vehicle queue lengths satisfy spatial lane capacity limits, including short lanes, for daily operation.

Refining of raw materials, lignite present economic problems

Energy Technology Data Exchange (ETDEWEB)

Schirmer, G.

1985-06-01

East Germany seeks an economic intensification program that involves refining raw materials to a higher level. Lignite briquetting prior to liquefaction and gasification illustrates both the theoretical and practical aspects of that goal and also introduces questions of secure supplies. The author describes the special labor processes, use of technology, recycling of waste materials, and other new problems that the approach entails as the refined raw materials become new materials or energy sources. Economics based on the value of the refined product and the cost of the materials determine the degree of refinement. The concept also involves the relationship of producer and user as profits increase.

Chinese refining capacity for Canadian heavy oil

International Nuclear Information System (INIS)

Bruce, G.W.

2006-01-01

This paper discussed China's refining capacity in relation to exports of Canadian heavy oil. Demand for oil is increasing throughout the world, and China is expected to consume 25 per cent of the projected yearly oil supplies. Alberta currently has an estimated 174 billion barrels of recoverable bitumen, and produces 1.06 million barrels per day. Production is expected to increase to 4.5 million barrels per day by the year 2020. Currently bitumen blends are refined and diluted with naphtha and sweet synthetic crude oil. Bitumen is a challenging feedstock for refineries, and requires thermal production methods or gasification processes. Primary conversion into sour synthetic crude is typically followed by hydrocracking and further refining into finished petroleum products. There are currently 50 refineries in China with a 7.4 million barrel per day capacity. Coastal refineries using imported crude oil have a 4 million barrel per day capacity. New facilities are being constructed and existing plants are being upgraded in order to process heavier and more sour crude oils. However, current refining capabilities in Chinese refineries have a limited ability for resid conversion. It was concluded that while China has a refining infrastructure, only refineries on the coast will use oil sands-derived feedstocks. However, there are currently opportunities to design refineries to match future feedstocks. tabs., figs

Refining revolution

Energy Technology Data Exchange (ETDEWEB)

Fesharaki, F.; Isaak, D.

1984-01-01

A review of changes in the oil refining industry since 1973 examines the drop in capacity use and its effect on profits of the Organization of Economic Cooperation and Development (OECD) countries compared to world refining. OPEC countries used their new oil revenues to expand Gulf refineries, which put additional pressure on OECD refiners. OPEC involvement in global marketing, however, could help to secure supplies. Scrapping some older OECD refineries could improve the percentage of capacity in use if new construction is kept to a minimum. Other issues facing refiners are the changes in oil demand patterns and government responses to the market. 2 tables.

Using atomic energy in the oil refining and petrochemical industry

Energy Technology Data Exchange (ETDEWEB)

Feigin, E.A.; Barashkov, R.Ia.; Raud, E.A.

1982-01-01

A short description of the basic large scale processes for oil refining and petrochemistry in which nuclear reactors can be used is given. The possible industrial plans for using nuclear reactors are examined together with the problems in using the advances in atomic technology in oil refining and petrochemical processes.

Plasma gasification process: Modeling, simulation and comparison with conventional air gasification

International Nuclear Information System (INIS)

Janajreh, Isam; Raza, Syed Shabbar; Valmundsson, Arnar Snaer

2013-01-01

Highlights: ► Plasma/conventional gasification are modeled via Gibbs energy minimization. ► The model is applied to wide range of feedstock, tire, biomass, coal, oil shale. ► Plasma gasification show high efficiency for tire waste and coal. ► Efficiency is around 42% for plasma and 72% for conventional gasification. ► Lower plasma gasification efficiency justifies hazardous waste energy recovery. - Abstract: In this study, two methods of gasification are developed for the gasification of various feedstock, these are plasma gasification and conventional air gasification. The two methods are based on non-stoichiometric Gibbs energy minimization approach. The model takes into account the different type of feedstocks, which are analyzed at waste to energy lab at Masdar Institute, oxidizer used along with the plasma energy input and accurately evaluates the syngas composition. The developed model is applied for several types of feedstock, i.e. waste tire material, coal, plywood, pine needles, oil shale, and municipal solid waste (MSW), algae, treated/untreated wood, instigating air/steam as the plasma gas and only air as oxidizer for conventional gasification. The results of plasma gasification and conventional air gasification are calculated on the bases of product gas composition and the process efficiency. Results of plasma gasification shows that high gasification efficiency is achievable using both tire waste material and coal, also, the second law efficiency is calculated for plasma gasification that shows a relative high efficiency for tire and coal as compare to other feedstock. The average process efficiency for plasma gasification is calculated to be around 42%. On other hand the result of conventional gasification shows an average efficiency of 72%. The low efficiency of plasma gasification suggest that if only the disposal of hazard waste material is considered then plasma gasification can be a viable option to recover energy.

Toxicological evaluation of natural rubber films from vulcanized latex by the conventional process and the alternative process with ionizing radiation

International Nuclear Information System (INIS)

Campos, Vania Elisabeth

1997-01-01

The industrial vulcanization of natural rubber latex (NRL) is made all over the world by conventional process using sulphur and heat but it can be made by an alternative process using ionizing radiation. In this research the NRL was tested by 13 physical, chemical and mechanical assays which showed its good quality. It was done a preliminary study of the toxicological properties of 4 natural rubber films obtained by casting process of NRL: one non vulcanized, other vulcanized by the conventional process and two vulcanized by the alternative process. In the alternative process the films were obtained by irradiation of NRL by gamma rays from the 60 Co source at 250 kGy in the absence of sensitizer and irradiated NRL at 12 kGy in the presence of 4ph r of n-butyl acrylate / 0.2 phr of KOH. These vulcanization doses were determined from broken tensile strength. In the conventional process, sulphur vulcanized NRL was made using a classical composition. Another film was made with non vulcanized NRL. The preliminary evaluation of the toxicological properties was made from in vitro cytotoxicity and in vivo systemic toxicity assays. The LBN films vulcanized by the alternative process have less cytotoxicity than the NRL film vulcanized by the conventional process. The sensitized vulcanized films by gamma rays and non vulcanized films showed similar cytotoxicity while the vulcanized films without sensitizer showed a slight lower cytotoxicity. The non vulcanized NRL film and the NRL films vulcanized by the alternative process did not show toxic effects int he 72 hours period of the systemic toxicity assay. However the NRL film vulcanized with sulphur induced effects like allaying and motor in coordination on the animals treated with an oil extract at the fourth hour and recovering after that. The alternative process promoted lower toxic effects than conventional process because there was no toxic substances present. (author)

Refinement of NMR structures using implicit solvent and advanced sampling techniques.

Science.gov (United States)

Chen, Jianhan; Im, Wonpil; Brooks, Charles L

2004-12-15

NMR biomolecular structure calculations exploit simulated annealing methods for conformational sampling and require a relatively high level of redundancy in the experimental restraints to determine quality three-dimensional structures. Recent advances in generalized Born (GB) implicit solvent models should make it possible to combine information from both experimental measurements and accurate empirical force fields to improve the quality of NMR-derived structures. In this paper, we study the influence of implicit solvent on the refinement of protein NMR structures and identify an optimal protocol of utilizing these improved force fields. To do so, we carry out structure refinement experiments for model proteins with published NMR structures using full NMR restraints and subsets of them. We also investigate the application of advanced sampling techniques to NMR structure refinement. Similar to the observations of Xia et al. (J.Biomol. NMR 2002, 22, 317-331), we find that the impact of implicit solvent is rather small when there is a sufficient number of experimental restraints (such as in the final stage of NMR structure determination), whether implicit solvent is used throughout the calculation or only in the final refinement step. The application of advanced sampling techniques also seems to have minimal impact in this case. However, when the experimental data are limited, we demonstrate that refinement with implicit solvent can substantially improve the quality of the structures. In particular, when combined with an advanced sampling technique, the replica exchange (REX) method, near-native structures can be rapidly moved toward the native basin. The REX method provides both enhanced sampling and automatic selection of the most native-like (lowest energy) structures. An optimal protocol based on our studies first generates an ensemble of initial structures that maximally satisfy the available experimental data with conventional NMR software using a simplified

Formal refinement of extended state machines

Directory of Open Access Journals (Sweden)

Thomas Fayolle

2016-06-01

Full Text Available In a traditional formal development process, e.g. using the B method, the informal user requirements are (manually translated into a global abstract formal specification. This translation is especially difficult to achieve. The Event-B method was developed to incrementally and formally construct such a specification using stepwise refinement. Each increment takes into account new properties and system aspects. In this paper, we propose to couple a graphical notation called Algebraic State-Transition Diagrams (ASTD with an Event-B specification in order to provide a better understanding of the software behaviour. The dynamic behaviour is captured by the ASTD, which is based on automata and process algebra operators, while the data model is described by means of an Event-B specification. We propose a methodology to incrementally refine such specification couplings, taking into account new refinement relations and consistency conditions between the control specification and the data specification. We compare the specifications obtained using each approach for readability and proof complexity. The advantages and drawbacks of the traditional approach and of our methodology are discussed. The whole process is illustrated by a railway CBTC-like case study. Our approach is supported by tools for translating ASTD's into B and Event-B into B.

Basic effects of pulp refining on fiber properties--a review.

Science.gov (United States)

Gharehkhani, Samira; Sadeghinezhad, Emad; Kazi, Salim Newaz; Yarmand, Hooman; Badarudin, Ahmad; Safaei, Mohammad Reza; Zubir, Mohd Nashrul Mohd

2015-01-22

The requirement for high quality pulps which are widely used in paper industries has increased the demand for pulp refining (beating) process. Pulp refining is a promising approach to improve the pulp quality by changing the fiber characteristics. The diversity of research on the effect of refining on fiber properties which is due to the different pulp sources, pulp consistency and refining equipment has interested us to provide a review on the studies over the last decade. In this article, the influence of pulp refining on structural properties i.e., fibrillations, fine formation, fiber length, fiber curl, crystallinity and distribution of surface chemical compositions is reviewed. The effect of pulp refining on electrokinetic properties of fiber e.g., surface and total charges of pulps is discussed. In addition, an overview of different refining theories, refiners as well as some tests for assessing the pulp refining is presented. Copyright © 2014 Elsevier Ltd. All rights reserved.

GAMER: A GRAPHIC PROCESSING UNIT ACCELERATED ADAPTIVE-MESH-REFINEMENT CODE FOR ASTROPHYSICS

International Nuclear Information System (INIS)

Schive, H.-Y.; Tsai, Y.-C.; Chiueh Tzihong

2010-01-01

We present the newly developed code, GPU-accelerated Adaptive-MEsh-Refinement code (GAMER), which adopts a novel approach in improving the performance of adaptive-mesh-refinement (AMR) astrophysical simulations by a large factor with the use of the graphic processing unit (GPU). The AMR implementation is based on a hierarchy of grid patches with an oct-tree data structure. We adopt a three-dimensional relaxing total variation diminishing scheme for the hydrodynamic solver and a multi-level relaxation scheme for the Poisson solver. Both solvers have been implemented in GPU, by which hundreds of patches can be advanced in parallel. The computational overhead associated with the data transfer between the CPU and GPU is carefully reduced by utilizing the capability of asynchronous memory copies in GPU, and the computing time of the ghost-zone values for each patch is diminished by overlapping it with the GPU computations. We demonstrate the accuracy of the code by performing several standard test problems in astrophysics. GAMER is a parallel code that can be run in a multi-GPU cluster system. We measure the performance of the code by performing purely baryonic cosmological simulations in different hardware implementations, in which detailed timing analyses provide comparison between the computations with and without GPU(s) acceleration. Maximum speed-up factors of 12.19 and 10.47 are demonstrated using one GPU with 4096 3 effective resolution and 16 GPUs with 8192 3 effective resolution, respectively.

Corrosion behaviour of some conventional stainless steels in electrolyzing process

Directory of Open Access Journals (Sweden)

Amal NASSAR

2015-12-01

Full Text Available In this study, attempts were made to increase the amount of hydrogen generated from the water electrolysis process. Some conventional stainless steels (316; 409; 410 and 430 were used as anode and cathode in electrolysis process. Further study was carried out on the corrosion trend in all the investigated metals. It is observed that the electrode material can effect on the amount of hydrogen generate by electrolyzing process and metal composition of the stainless steels effects on the rate of corrosion.

Production of Al-Ti-C grain refiners with the addition of elemental carbon

International Nuclear Information System (INIS)

Gezer, Berke Turgay; Toptan, Fatih; Daglilar, Sibel; Kerti, Isil

2010-01-01

Grain refining process used in aluminium alloys, has an important role for preventing columnar, coarse grains and encouraging fine, equiaxed grain formation. Al-Ti-B grain refiners are widely used as aluminium grain refiners despite the problems in application Al-Ti-C refiners have an increasing demand in recent years. In the present work, Al-Ti-C grain refiners with different Ti:C ratios were produced by insitu method with the addition of elemental carbon. Microstructures were characterised by optic microscope and scanning electron microscope equipped with energy dispersive spectroscopy. The effects of temperature, holding time and Ti:C ratio on the grain refinement process were investigated and optimum conditions were determined.

Review of conventional and novel food processing methods on food allergens.

Science.gov (United States)

Vanga, Sai Kranthi; Singh, Ashutosh; Raghavan, Vijaya

2017-07-03

With the turn of this century, novel food processing techniques have become commercially very important because of their profound advantages over the traditional methods. These novel processing methods tend to preserve the characteristic properties of food including their organoleptic and nutritional qualities better when compared with the conventional food processing methods. During the same period of time, there is a clear rise in the populations suffering from food allergies, especially infants and children. Though, this fact is widely attributed to the changing livelihood of population in both developed and developing nations and to the introduction of new food habits with advent of novel foods and new processing techniques, their complete role is still uncertain. Under the circumstance, it is very important to understand the structural changes in the protein as food is processed to comprehend whether the specific processing technique (conventional and novel) is increasing or mitigating the allergenicity. Various modern means are now being employed to understand the conformational changes in the protein which can affect the allergenicity. In this review, the processing effects on protein structure and allergenicity are discussed along with the insinuations of recent studies and techniques for establishing a platform to investigate future pathway to reduce or eliminate allergenicity in the population.

On Syntactic and Semantic Action Refinement

NARCIS (Netherlands)

Goltz, Ursula; Gorrieri, Roberto; Rensink, Arend

1992-01-01

The semantic definition of action refinement on labelled event structures is compared with the notion of syntactic substitution,which can be used as another notion of action refiment in a process algebraic setting. This is done by studying a process algebra equipped with the ACP sequential

Uranium refining by solvent extraction

International Nuclear Information System (INIS)

Kraikaew, J.

1996-01-01

The yellow cake refining was studied in both laboratory and semi-pilot scales. The process units mainly consist of dissolution and filtration, solvent extraction, and precipitation and filtration. Effect of flow ratio (organic flow rate/ aqueous flow rate) on working efficiencies of solvent extraction process was studied. Detailed studies were carried out on extraction, scrubbing and stripping processes. Purity of yellow cake product obtained is high as 90.32% U 3 O 8

Modelling Embedded Systems by Non-Monotonic Refinement

NARCIS (Netherlands)

Mader, Angelika H.; Marincic, J.; Wupper, H.

2008-01-01

This paper addresses the process of modelling embedded sys- tems for formal verification. We propose a modelling process built on non-monotonic refinement and a number of guidelines. The outcome of the modelling process is a model, together with a correctness argument that justifies our modelling

Refining mineral oils

Energy Technology Data Exchange (ETDEWEB)

1946-07-05

A process is described refining raw oils such as mineral oils, shale oils, tar, their fractions and derivatives, by extraction with a selected solvent or a mixture of solvents containing water, forming a solvent more favorable for the hydrocarbons poor in hydrogen than for hydrocarbons rich in hydrogen, this process is characterized by the addition of an aiding solvent for the water which can be mixed or dissolved in the water and the solvent or in the dissolving mixture and increasing in this way the solubility of the water in the solvent or the dissolving mixture.

Impact of operating variables on re-refining of vehicle waste oil to base-oil by acid-clay process

International Nuclear Information System (INIS)

Durrani, H.A.; Panhwar, M.I.; Kazi, R.A.

2009-01-01

A large volume of waste oil is generated each year as the number of vehicles in the country is increasing every day. This used lubricant oil constitutes a serious pollution problem. It easily be converted as a resource depending on the manners of utilization and management. This paper compares various end uses of waste oil and develops technology by which basic properties of the base oil can be regained. An experimental setup (Experimental rig) of acid-clay method was used to regain waste oil collected and number of experiments were conducted by varying different process variables. The impacts of the operating variables on the quality of re-refined oil are also discussed. The recovery of re-refined base oil was found in between 44-49%. (author)

Influence of refining process on the porosity of high pressure die casting alloy Al-Si

Directory of Open Access Journals (Sweden)

A.W. Orlowicz

2009-04-01

Full Text Available This study presents research results of the influence that refining and transfer of AlSi12S alloy on the porosity of high pressure diecastings.Tests were conducted under production conditions of Die-casting Foundry META-ZEL Sp z o.o. The operation of refining was conducted in a melting furnace, with the use of an FDU Mini Degasser. Decay of the refining effect was assessed by evaluating the porosity content and metallographic examination.

New Insights on Degumming and Bleaching Process Parameters on The Formation of 3-Monochloropropane-1,2-Diol Esters and Glycidyl Esters in Refined, Bleached, Deodorized Palm Oil.

Science.gov (United States)

Sim, Biow Ing; Muhamad, Halimah; Lai, Oi Ming; Abas, Faridah; Yeoh, Chee Beng; Nehdi, Imededdine Arbi; Khor, Yih Phing; Tan, Chin Ping

2018-04-01

This paper examines the interactions of degumming and bleaching processes as well as their influences on the formation of 3-monochloropropane-1,2-diol esters (3-MCPDE) and glycidyl esters in refined, bleached and deodorized palm oil by using D-optimal design. Water degumming effectively reduced the 3-MCPDE content up to 50%. Acid activated bleaching earth had a greater effect on 3-MCPDE reduction compared to natural bleaching earth and acid activated bleaching earth with neutral pH, indicating that performance and adsorption capacities of bleaching earth are the predominant factors in the removal of esters, rather than its acidity profile. The combination of high dosage phosphoric acid during degumming with the use of acid activated bleaching earth eliminated almost all glycidyl esters during refining. Besides, the effects of crude palm oil quality was assessed and it was found that the quality of crude palm oil determines the level of formation of 3-MCPDE and glycidyl esters in palm oil during the high temperature deodorization step of physical refining process. Poor quality crude palm oil has strong impact towards 3-MCPDE and glycidyl esters formation due to the intrinsic components present within. The findings are useful to palm oil refining industry in choosing raw materials as an input during the refining process.

Basic investigations to improve the refinement process of coal. Grundlagenuntersuchungen zur Erhoehung des Veredlungsverhaltens von Kohlen

Energy Technology Data Exchange (ETDEWEB)

Krug, H; Naundorf, W; Trommer, D

1985-01-01

In the four articles in this issue, variants of the process for the effective use and improved refinement of brown coal are described. There are reports on the manufacture of special briquettes from briquette coal slack and on the briquetting behaviour of dry brown coal dust and the briquetting and coking behaviour of hard foreign brown coal containing a lot of ash. The four articles are dealt with separately. With 52 figs., 10 tabs.

Biomolecular structure refinement using the GROMOS simulation software

International Nuclear Information System (INIS)

Schmid, Nathan; Allison, Jane R.; Dolenc, Jožica; Eichenberger, Andreas P.; Kunz, Anna-Pitschna E.; Gunsteren, Wilfred F. van

2011-01-01

For the understanding of cellular processes the molecular structure of biomolecules has to be accurately determined. Initial models can be significantly improved by structure refinement techniques. Here, we present the refinement methods and analysis techniques implemented in the GROMOS software for biomolecular simulation. The methodology and some implementation details of the computation of NMR NOE data, 3 J-couplings and residual dipolar couplings, X-ray scattering intensities from crystals and solutions and neutron scattering intensities used in GROMOS is described and refinement strategies and concepts are discussed using example applications. The GROMOS software allows structure refinement combining different types of experimental data with different types of restraining functions, while using a variety of methods to enhance conformational searching and sampling and the thermodynamically calibrated GROMOS force field for biomolecular simulation.

Biomolecular structure refinement using the GROMOS simulation software

Energy Technology Data Exchange (ETDEWEB)

Schmid, Nathan; Allison, Jane R.; Dolenc, Jozica; Eichenberger, Andreas P.; Kunz, Anna-Pitschna E.; Gunsteren, Wilfred F. van, E-mail: wfvgn@igc.phys.chem.ethz.ch [Swiss Federal Institute of Technology ETH, Laboratory of Physical Chemistry (Switzerland)

2011-11-15

For the understanding of cellular processes the molecular structure of biomolecules has to be accurately determined. Initial models can be significantly improved by structure refinement techniques. Here, we present the refinement methods and analysis techniques implemented in the GROMOS software for biomolecular simulation. The methodology and some implementation details of the computation of NMR NOE data, {sup 3}J-couplings and residual dipolar couplings, X-ray scattering intensities from crystals and solutions and neutron scattering intensities used in GROMOS is described and refinement strategies and concepts are discussed using example applications. The GROMOS software allows structure refinement combining different types of experimental data with different types of restraining functions, while using a variety of methods to enhance conformational searching and sampling and the thermodynamically calibrated GROMOS force field for biomolecular simulation.

Decontamination of transuranic contaminated metals by melt refining

International Nuclear Information System (INIS)

Heshmatpour, B.; Copeland, G.L.; Heestand, R.L.

1983-01-01

Melt refining of transuranic contaminated metals is a possible decontamination process with the potential advantages of producing metal for reuse and of simplifying chemical analyses. By routinely achieving the 10 nCi/g( about0.1ppm) level by melt refining, scrap metal can be removed from the transuranic waste category. (To demonstrate the effectiveness of this melt refining process, mild steel, stainless steel, nickel, and copper were contaminated with 500 ppm (μg/g) PuO 2 and melted with various fluxes. The solidified slags and metals were analyzed for their plutonium contents, and corresponding partition ratios for plutonium were calculated. Some metals were double refined in order to study the effect of secondary slag treatment. The initial weight of the slags was also varied to investigate the effect of slag weight on the degree of plutonium removal. In general, all four metals could be decontaminated below 1 ppm (μg/g) Pu ( about100 nCi/g) by a single slag treatment. Doubling the slag weight did not improve decontamination significantly; however, double slag treatment using 5 wt.% slag did decontaminate the metals to below 0.1 ppm (μg/g) Pu (10 nCi/g).)

An interactive medical image segmentation framework using iterative refinement.

Science.gov (United States)

Kalshetti, Pratik; Bundele, Manas; Rahangdale, Parag; Jangra, Dinesh; Chattopadhyay, Chiranjoy; Harit, Gaurav; Elhence, Abhay

2017-04-01

Segmentation is often performed on medical images for identifying diseases in clinical evaluation. Hence it has become one of the major research areas. Conventional image segmentation techniques are unable to provide satisfactory segmentation results for medical images as they contain irregularities. They need to be pre-processed before segmentation. In order to obtain the most suitable method for medical image segmentation, we propose MIST (Medical Image Segmentation Tool), a two stage algorithm. The first stage automatically generates a binary marker image of the region of interest using mathematical morphology. This marker serves as the mask image for the second stage which uses GrabCut to yield an efficient segmented result. The obtained result can be further refined by user interaction, which can be done using the proposed Graphical User Interface (GUI). Experimental results show that the proposed method is accurate and provides satisfactory segmentation results with minimum user interaction on medical as well as natural images. Copyright © 2017 Elsevier Ltd. All rights reserved.

Preparation and characterization of semi-refined kappa carrageenan-based edible film for nano coating application on minimally processed food

Science.gov (United States)

Manuhara, Godras Jati; Praseptiangga, Danar; Muhammad, Dimas Rahadian Aji; Maimuni, Bawani Hindami

2016-02-01

Shorter and easier processing of semi-refined kappa carrageenan extracted from Euchema cottonii red seaweed result in cheaper price of the polysaccharide. In this study, edible film was prepared from the semi-refined carrageenan without any salt addition. The effect of the carrageenan concentration (1.0, 1.5, and 2.0% w/v) on physical and mechanical properties of the edible film was studied. Edible film thickness and tensile strength increased but elongation at break and water vapor transmission rate (WVTR) decreased as the concentration increased. Based on the characteristic of the edible film, formulation using 2% carrageenan was recommended. The edible film demonstrated the characteristic as follow: 0.054 mm thickness, 21.14 MPa tensile strength, 12.36% elongation at break, and 9.56 g/m2.hour WVTR. It was also noted the carrageenan-based edible film indicated potential physical and mechanical characteristics for nano coating applications on minimally processed food.

Study of mechanism on microstructure refinement during compact strip production process

International Nuclear Information System (INIS)

Yu Hao; Kang Yonglin; Wang Kelu; Fu Jie; Wang Zhongbing; Liu Delu

2003-01-01

In this study, microstructures of 1.9 mm hot strip steel produced by compact strip production (CSP) are investigated by using optical metallograph observation and electron back-scattered diffraction (EBSD) data to deduce the status of hot rolled austenite before phase transformation, because the evolution of hot rolled austenite is important to provide information for the microstructure refinement. The experimental results show that the finishing hot rolled microstructure is a mixture of recrystallized and deformed austenite, and the percentage of recrystallized austenite is greater than that of the deformed austenite. At last, microstructure evolution of austenite is modeled based on chemical compositions and techniques of producing 1.9 mm hot strip. The simulation results agree well with experimental data. Analysis shows that microstructure refinement, recrystallization and supercooling rate are the primary causes to fine microstructure

P-Refinement and P-Threads (Preprint)

National Research Council Canada - National Science Library

Dong, Steven; Karniadakis, George E

2002-01-01

...]) in d dimensions, which is higher than lower-order methods. In this paper, we demonstrate that by employing multi-threading within MPI processes we manage to counter- balance the cost increase associated with P-refinement...

Third-Party Evaluation of Petro Tex Hydrocarbons, LLC, ReGen Lubricating Oil Re-refining Process

Energy Technology Data Exchange (ETDEWEB)

Compere, A L [ORNL; Griffith, William {Bill} L [ORNL

2009-04-01

This report presents an assessment of market, energy impact, and utility of the PetroTex Hydrocarbons, LLC., ReGen process for re-refining used lubricating oil to produce Group I, II, and III base oils, diesel fuel, and asphalt. PetroTex Hydrocarbons, LLC., has performed extensive pilot scale evaluations, computer simulations, and market studies of this process and is presently evaluating construction of a 23 million gallon per year industrial-scale plant. PetroTex has obtained a 30 acre site in the Texas Industries RailPark in Midlothian Texas. The environmental and civil engineering assessments of the site are completed, and the company has been granted a special use permit from the City of Midlothian and air emissions permits for the Texas Commission on Environmental Quality.

Challenges and choices : a U.S. refiner's perspective on Western Canadian crude

International Nuclear Information System (INIS)

Cook, C.

2004-01-01

This presentation included a map depicting refineries, pipelines, terminals, coastal terminals and inland terminals in the eastern United States. Major oil trade movements between the United States, Canada, Mexico, South America, Central America, Europe, Middle East, Africa, and Asia-Pacific were also illustrated. A graph depicting Western Canada's long range crude supply forecast shows a decrease in conventional heavy oil supply but an increase in supply of diluent bitumen blend and synthetic bitumen blends. The presentation focused on this shift in refining and how product quality is viewed differently by producers and refiners in terms of gravity, sulfur content, boiling range distribution, distillate cetane, total acid number (TAN), asphalt properties, nitrogen and particulates. Refiners are looking for affordability, quality, consistency, yields and unit balance. Canadian marketing connections to PADD 1, 2, 4 and 5 were outlined. It was noted that more than 45 refineries in over 20 regions in the United States use Western Canadian crude oil. 22 figs

Accurate macromolecular crystallographic refinement: incorporation of the linear scaling, semiempirical quantum-mechanics program DivCon into the PHENIX refinement package

Energy Technology Data Exchange (ETDEWEB)

Borbulevych, Oleg Y.; Plumley, Joshua A.; Martin, Roger I. [QuantumBio Inc., 2790 West College Avenue, State College, PA 16801 (United States); Merz, Kenneth M. Jr [University of Florida, Gainesville, Florida (United States); Westerhoff, Lance M., E-mail: lance@quantumbioinc.com [QuantumBio Inc., 2790 West College Avenue, State College, PA 16801 (United States)

2014-05-01

Semiempirical quantum-chemical X-ray macromolecular refinement using the program DivCon integrated with PHENIX is described. Macromolecular crystallographic refinement relies on sometimes dubious stereochemical restraints and rudimentary energy functionals to ensure the correct geometry of the model of the macromolecule and any covalently bound ligand(s). The ligand stereochemical restraint file (CIF) requires a priori understanding of the ligand geometry within the active site, and creation of the CIF is often an error-prone process owing to the great variety of potential ligand chemistry and structure. Stereochemical restraints have been replaced with more robust functionals through the integration of the linear-scaling, semiempirical quantum-mechanics (SE-QM) program DivCon with the PHENIX X-ray refinement engine. The PHENIX/DivCon package has been thoroughly validated on a population of 50 protein–ligand Protein Data Bank (PDB) structures with a range of resolutions and chemistry. The PDB structures used for the validation were originally refined utilizing various refinement packages and were published within the past five years. PHENIX/DivCon does not utilize CIF(s), link restraints and other parameters for refinement and hence it does not make as many a priori assumptions about the model. Across the entire population, the method results in reasonable ligand geometries and low ligand strains, even when the original refinement exhibited difficulties, indicating that PHENIX/DivCon is applicable to both single-structure and high-throughput crystallography.

Assessing food allergy risks from residual peanut protein in highly refined vegetable oil

NARCIS (Netherlands)

Blom, W.M.; Kruizinga, A.G.; Rubingh, C.M.; Remington, B.C.; Crevel, R.W.R.; Houben, G.F.

2017-01-01

Refined vegetable oils including refined peanut oil are widely used in foods. Due to shared production processes, refined non-peanut vegetable oils can contain residual peanut proteins. We estimated the predicted number of allergic reactions to residual peanut proteins using probabilistic risk

Computational prediction of the refinement of oxide agglomerates in a physical conditioning process for molten aluminium alloy

International Nuclear Information System (INIS)

Tong, M; Jagarlapudi, S C; Browne, D J; Patel, J B; Stone, I C; Fan, Z

2015-01-01

Physically conditioning molten scrap aluminium alloys using high shear processing (HSP) was recently found to be a promising technology for purification of contaminated alloys. HSP refines the solid oxide agglomerates in molten alloys, so that they can act as sites for the nucleation of Fe-rich intermetallic phases which can subsequently be removed by the downstream de-drossing process. In this paper, a computational modelling for predicting the evolution of size of oxide clusters during HSP is presented. We used CFD to predict the macroscopic flow features of the melt, and the resultant field predictions of temperature and melt shear rate were transferred to a population balance model (PBM) as its key inputs. The PBM is a macroscopic model that formulates the microscopic agglomeration and breakage of a population of a dispersed phase. Although it has been widely used to study conventional deoxidation of liquid metal, this is the first time that PBM has been used to simulate the melt conditioning process within a rotor/stator HSP device. We employed a method which discretizes the continuous profile of size of the dispersed phase into a collection of discrete bins of size, to solve the governing population balance equation for the size of agglomerates. A finite volume method was used to solve the continuity equation, the energy equation and the momentum equation. The overall computation was implemented mainly using the FLUENT module of ANSYS. The simulations showed that there is a relatively high melt shear rate between the stator and sweeping tips of the rotor blades. This high shear rate leads directly to significant fragmentation of the initially large oxide aggregates. Because the process of agglomeration is significantly slower than the breakage processes at the beginning of HSP, the mean size of oxide clusters decreases very rapidly. As the process of agglomeration gradually balances the process of breakage, the mean size of oxide clusters converges to a

Computational prediction of the refinement of oxide agglomerates in a physical conditioning process for molten aluminium alloy

Science.gov (United States)

Tong, M.; Jagarlapudi, S. C.; Patel, J. B.; Stone, I. C.; Fan, Z.; Browne, D. J.

2015-06-01

Physically conditioning molten scrap aluminium alloys using high shear processing (HSP) was recently found to be a promising technology for purification of contaminated alloys. HSP refines the solid oxide agglomerates in molten alloys, so that they can act as sites for the nucleation of Fe-rich intermetallic phases which can subsequently be removed by the downstream de-drossing process. In this paper, a computational modelling for predicting the evolution of size of oxide clusters during HSP is presented. We used CFD to predict the macroscopic flow features of the melt, and the resultant field predictions of temperature and melt shear rate were transferred to a population balance model (PBM) as its key inputs. The PBM is a macroscopic model that formulates the microscopic agglomeration and breakage of a population of a dispersed phase. Although it has been widely used to study conventional deoxidation of liquid metal, this is the first time that PBM has been used to simulate the melt conditioning process within a rotor/stator HSP device. We employed a method which discretizes the continuous profile of size of the dispersed phase into a collection of discrete bins of size, to solve the governing population balance equation for the size of agglomerates. A finite volume method was used to solve the continuity equation, the energy equation and the momentum equation. The overall computation was implemented mainly using the FLUENT module of ANSYS. The simulations showed that there is a relatively high melt shear rate between the stator and sweeping tips of the rotor blades. This high shear rate leads directly to significant fragmentation of the initially large oxide aggregates. Because the process of agglomeration is significantly slower than the breakage processes at the beginning of HSP, the mean size of oxide clusters decreases very rapidly. As the process of agglomeration gradually balances the process of breakage, the mean size of oxide clusters converges to a

Cooking processes increase bioactive compounds in organic and conventional green beans.

Science.gov (United States)

Lima, Giuseppina Pace Pereira; Costa, Sergio Marques; Monaco, Kamila de Almeida; Uliana, Maira Rodrigues; Fernandez, Roberto Morato; Correa, Camila Renata; Vianello, Fabio; Cisneros-Zevallos, Luis; Minatel, Igor Otavio

2017-12-01

The influence of cooking methods on chlorophyl, carotenoids, polyamines, polyphenols contents and antioxidant capacity were analyzed in organic and conventional green beans. The initial raw material had a higher content of chlorophyl and total phenolics in conventional green beans, whereas organic cultive favored flavonoid content and antioxidant capacity. Polyamines and carotenoids were similar for the two crop systems. After the cooking process, carotenoids (β-carotene, lutein and zeaxanthin) increased. Microwave heating favored the enhancement of some polar compounds, whereas pressure cooking favored carotenoids. When we used the estimation of the radical scavenging activity by electron spin resonance (ESR) spectroscopy, a reduction of the DPPH radical signal in the presence of green bean extracts was observed, regardless of the mode of cultivation. The highest reduction of the ESR signal ocurred for microwave cooking in organic and conventional green beans, indicating a higher availability of antioxidants with this type of heat treatment.

Declarative event based models of concurrency and refinement in psi-calculi

DEFF Research Database (Denmark)

Normann, Håkon; Johansen, Christian; Hildebrandt, Thomas

2015-01-01

Psi-calculi constitute a parametric framework for nominal process calculi, where constraint based process calculi and process calculi for mobility can be defined as instances. We apply here the framework of psi-calculi to provide a foundation for the exploration of declarative event-based process...... calculi with support for run-time refinement. We first provide a representation of the model of finite prime event structures as an instance of psi-calculi and prove that the representation respects the semantics up to concurrency diamonds and action refinement. We then proceed to give a psi......-calculi representation of Dynamic Condition Response Graphs, which conservatively extends prime event structures to allow finite representations of (omega) regular finite (and infinite) behaviours and have been shown to support run-time adaptation and refinement. We end by outlining the final aim of this research, which...

Refining crude oils and gasolines, etc

Energy Technology Data Exchange (ETDEWEB)

1931-11-23

A process of refining crude oils and gasolines distilled from shale and the like is described, consisting of submitting them to a prewash with soda, an oxidation preferably with hypochlorite solution, a hydrogenation with nascent hydrogen, and finally rectification and neutralization.

Microstructures and Grain Refinement of Additive-Manufactured Ti- xW Alloys

Science.gov (United States)

Mendoza, Michael Y.; Samimi, Peyman; Brice, David A.; Martin, Brian W.; Rolchigo, Matt R.; LeSar, Richard; Collins, Peter C.

2017-07-01

It is necessary to better understand the composition-processing-microstructure relationships that exist for materials produced by additive manufacturing. To this end, Laser Engineered Net Shaping (LENS™), a type of additive manufacturing, was used to produce a compositionally graded titanium binary model alloy system (Ti- xW specimen (0 ≤ x ≤ 30 wt pct), so that relationships could be made between composition, processing, and the prior beta grain size. Importantly, the thermophysical properties of the Ti- xW, specifically its supercooling parameter ( P) and growth restriction factor ( Q), are such that grain refinement is expected and was observed. The systematic, combinatorial study of this binary system provides an opportunity to assess the mechanisms by which grain refinement occurs in Ti-based alloys in general, and for additive manufacturing in particular. The operating mechanisms that govern the relationship between composition and grain size are interpreted using a model originally developed for aluminum and magnesium alloys and subsequently applied for titanium alloys. The prior beta grain factor observed and the interpretations of their correlations indicate that tungsten is a good grain refiner and such models are valid to explain the grain-refinement process. By extension, other binary elements or higher order alloy systems with similar thermophysical properties should exhibit similar grain refinement.

Accurate macromolecular crystallographic refinement: incorporation of the linear scaling, semiempirical quantum-mechanics program DivCon into the PHENIX refinement package.

Science.gov (United States)

Borbulevych, Oleg Y; Plumley, Joshua A; Martin, Roger I; Merz, Kenneth M; Westerhoff, Lance M

2014-05-01

Macromolecular crystallographic refinement relies on sometimes dubious stereochemical restraints and rudimentary energy functionals to ensure the correct geometry of the model of the macromolecule and any covalently bound ligand(s). The ligand stereochemical restraint file (CIF) requires a priori understanding of the ligand geometry within the active site, and creation of the CIF is often an error-prone process owing to the great variety of potential ligand chemistry and structure. Stereochemical restraints have been replaced with more robust functionals through the integration of the linear-scaling, semiempirical quantum-mechanics (SE-QM) program DivCon with the PHENIX X-ray refinement engine. The PHENIX/DivCon package has been thoroughly validated on a population of 50 protein-ligand Protein Data Bank (PDB) structures with a range of resolutions and chemistry. The PDB structures used for the validation were originally refined utilizing various refinement packages and were published within the past five years. PHENIX/DivCon does not utilize CIF(s), link restraints and other parameters for refinement and hence it does not make as many a priori assumptions about the model. Across the entire population, the method results in reasonable ligand geometries and low ligand strains, even when the original refinement exhibited difficulties, indicating that PHENIX/DivCon is applicable to both single-structure and high-throughput crystallography.

Optimizing the treatment of landfill leachate by conventional Fenton and photo-Fenton processes

International Nuclear Information System (INIS)

Hermosilla, Daphne; Cortijo, Manuel; Huang, Chin Pao

2009-01-01

Landfill, a matured and economically appealing technology, is the ultimate approach for the management of municipal solid wastes. However, the inevitable generation of leachate from landfill requires further treatment. Among the various leachate treatment technologies available, advanced oxidation processes (AOPs) are among powerful methods to deal with the refractory organic constituents, and the Fenton reagent has evolved as one promising AOPs for the treatment of leachates. Particularly, the combination of UV-radiation with Fenton's reagent has been reported to be a method that allows both the photo-regeneration of Fe 2+ and photo-decarboxylation of ferric carboxylates. In this study, Fenton and photo-Fenton processes were fine tuned for the treatment of leachates from the Colmenar Viejo (Madrid, Spain) Landfill. Results showed that it is possible to define a set of conditions under which the same COD and TOC removals (approx 70%) could be achieved with both the conventional and photo-Fenton processes. But Fenton process generated an important quantity of iron sludge, which will require further disposal, when performed under optimal COD removal conditions. Furthermore conventional Fenton process was able to achieve slightly over an 80% COD removal from a 'young' leachate, while for 'old' and 'mixed' leachates was close to a 70%. The main advantage showed by the photo-assisted Fenton treatment of landfill leachate was that it consumed 32 times less iron and produced 25 times less sludge volume yielding the same COD removal results than a conventional Fenton treatment.

Transform domain Wyner-Ziv video coding with refinement of noise residue and side information

DEFF Research Database (Denmark)

Huang, Xin; Forchhammer, Søren

2010-01-01

are successively updating the estimated noise residue for noise modeling and side information frame quality during decoding. Experimental results show that the proposed decoder can improve the Rate- Distortion (RD) performance of a state-of-the-art Wyner Ziv video codec for the set of test sequences.......Distributed Video Coding (DVC) is a video coding paradigm which mainly exploits the source statistics at the decoder based on the availability of side information at the decoder. This paper considers feedback channel based Transform Domain Wyner-Ziv (TDWZ) DVC. The coding efficiency of TDWZ video...... coding does not match that of conventional video coding yet, mainly due to the quality of side information and inaccurate noise estimation. In this context, a novel TDWZ video decoder with noise residue refinement (NRR) and side information refinement (SIR) is proposed. The proposed refinement schemes...

Bitumen to refined products and petrochemicals : a preliminary assessment

International Nuclear Information System (INIS)

Crandall, G.

2004-01-01

Purvin and Gertz is an energy consulting firm that provides advise to the energy sector. A review of western Canadian crude oil supply suggests that oil sands production will surpass declining conventional production. Oil sands supply includes synthetic crude oil (SCO), bitumen and diluent. It is expected that oil sands will increase from 42 per cent of western supply in 2002 to 78 per cent in 2015. This presentation reviewed the potential of Alberta's oil sands and presented a recent study of refined products and petrochemicals from bitumen. Upgrading, refining and petrochemical case studies were presented. In particular, the author examined if a Canadian oil sands upgrading project with high capital costs can be competitive with competing projects in the United States and internationally. In addition to supply and demand issues, the presentation examined infrastructure capability and market potential in the United States. The economic potential and risks of preferred business cases compared to upgrading to SCO were also evaluated. tabs., figs

Potency of high-intensity ultrasonic treatment for grain refinement of magnesium alloys

International Nuclear Information System (INIS)

Ramirez, A.; Qian Ma; Davis, B.; Wilks, T.; StJohn, D.H.

2008-01-01

High-intensity ultrasonic treatment (UT) for grain refinement of magnesium alloys has been investigated using a novel theoretical approach in order to better understand its grain-refining potential and the mechanism of nucleation. The process demonstrated significantly superior grain-refining potency to carbon inoculation for Al-containing magnesium alloys but inferior potency to zirconium for Al-free alloys. Details revealed by applying the theoretical approach to ultrasonic grain refinement provide new clues to understanding the mechanism of grain nucleation by UT

Singapore refiners in midst of huge construction campaign

International Nuclear Information System (INIS)

Land, R.

1992-01-01

This paper reports that Singapore's downstream capacity continues to mushroom. Singapore refiners, upbeat about long term prospects for petroleum products demand in the Asia-Pacific region, and are pressing plans to boost processing capacity. Their plans go beyond capacity expansions. They are proceeding with projects to upgrade refineries to emphasize production of higher value products and to further integrate refining capabilities wit the region's petrochemical industry. Planned expansion and upgrading projects at Singapore refineries call for outlays of more than $1 billion to boost total capacity to about 1.1 million b/d in 1993 and 1.27 million b/d by 1995. That would be the highest level since the mid-1980s, when refiners such as Shell Singapore cut capacity amid an oil glut. Singapore refineries currently are running at effective full capacity of 1.04 million b/d. Meanwhile, Singapore refiners are aggressively courting customers in the Indochina subcontinent, where long isolated centrally planned economies are turning gradually to free markets

Petroleum refining industry in China

International Nuclear Information System (INIS)

Walls, W.D.

2010-01-01

The oil refining industry in China has faced rapid growth in oil imports of increasingly sour grades of crude with which to satisfy growing domestic demand for a slate of lighter and cleaner finished products sold at subsidized prices. At the same time, the world petroleum refining industry has been moving from one that serves primarily local and regional markets to one that serves global markets for finished products, as world refining capacity utilization has increased. Globally, refined product markets are likely to experience continued globalization until refining investments significantly expand capacity in key demand regions. We survey the oil refining industry in China in the context of the world market for heterogeneous crude oils and growing world trade in refined petroleum products. (author)

Grain refinement of DC cast magnesium alloys with intensive melt shearing

International Nuclear Information System (INIS)

Zuo, Y B; Jiang, B; Zhang, Y; Fan, Z

2012-01-01

A new direct chill (DC) casting process, melt conditioned DC (MC-DC) process, has been developed for the production of high quality billets/slabs of light alloys by application of intensive melt shearing through a rotor-stator high shear device during the DC casting process. The rotor-stator high shear device provides intensive melt shearing to disperse the naturally occurring oxide films, and other inclusions, while creating a microscopic flow pattern to homogenize the temperature and composition fields in the sump. In this paper, we report the grain refining effect of intensive melt shearing in the MC-DC casting processing. Experimental results on DC casting of Mg-alloys with and without intensive melt shearing have demonstrated that the MC-DC casting process can produce magnesium alloy billets with significantly refined microstructure. Such grain refinement in the MC-DC casting process can be attributed to enhanced heterogeneous nucleation by dispersed naturally occurring oxide particles, increased nuclei survival rate in uniform temperature and compositional fields in the sump, and potential contribution from dendrite arm fragmentation.

Determination of Cation Distributions in Mineral Structures by use of the Rietveld Full-Profile Refinement Technique

International Nuclear Information System (INIS)

Nord, A.G.

1986-01-01

Use of the Rietveld full-profile refinement technique with X-ray or neutron powder diffraction data for the determination of divalent-metal cation distributions in three mineral structure types (farringtonite, grafonite, sarcopside) is demonstrated. The accuracy of the conventional cation distribution coefficient Ksub(D) is about 5-10 percent with 24-46 parameters to be refined, and the averaged metal-oxygen distances are reliable and well correlated to the observed cation distribution pattern. In particular the usefulness of the Rietveld technique in combination with Moessbauer spectroscopy is stressed. Some concluding remarks are also given

On the refinement calculus

CERN Document Server

Vickers, Trevor

1992-01-01

On the Refinement Calculus gives one view of the development of the refinement calculus and its attempt to bring together - among other things - Z specifications and Dijkstra's programming language. It is an excellent source of reference material for all those seeking the background and mathematical underpinnings of the refinement calculus.

Architectural Refinement for the Design of Survivable Systems

National Research Council Canada - National Science Library

Ellison, Robert

2001-01-01

This paper describes a process for systematically refining an enterprise system architecture to resist recognize and recover from deliberate, malicious attacks by applying reusable design primitives...

Zone refining of sintered, microwave-derived YBCO superconductors

International Nuclear Information System (INIS)

Warrier, K.G.K.; Varma, H.K.; Mani, T.V.; Damodaran, A.D.; Balachandran, U.

1993-07-01

Post-sintering treatments such as zone melting under thermal gradient has been conducted on sintered YBCO tape cast films. YBCO precursor powder was derived through decomposition of a mixture of nitrates of cations in a microwave oven for ∼4 min. The resulting powder was characterized and made into thin sheets by tape casting and then sintered at 945 C for 5 h. The sintered tapes were subjected to repeated zone refining operations at relatively high speeds of ∼30 mm/h. A microstructure having uniformly oriented grains in the a-b plane throughout the bulk of the sample was obtained by three repeated zone refining operations. Details of precursor preparation, microwave processing and its advantages, zone refining conditions, and microstructural features are presented in this paper

Repetitive Identification of Structural Systems Using a Nonlinear Model Parameter Refinement Approach

Directory of Open Access Journals (Sweden)

Jeng-Wen Lin

2009-01-01

Full Text Available This paper proposes a statistical confidence interval based nonlinear model parameter refinement approach for the health monitoring of structural systems subjected to seismic excitations. The developed model refinement approach uses the 95% confidence interval of the estimated structural parameters to determine their statistical significance in a least-squares regression setting. When the parameters' confidence interval covers the zero value, it is statistically sustainable to truncate such parameters. The remaining parameters will repetitively undergo such parameter sifting process for model refinement until all the parameters' statistical significance cannot be further improved. This newly developed model refinement approach is implemented for the series models of multivariable polynomial expansions: the linear, the Taylor series, and the power series model, leading to a more accurate identification as well as a more controllable design for system vibration control. Because the statistical regression based model refinement approach is intrinsically used to process a “batch” of data and obtain an ensemble average estimation such as the structural stiffness, the Kalman filter and one of its extended versions is introduced to the refined power series model for structural health monitoring.

Optimizing the treatment of landfill leachate by conventional Fenton and photo-Fenton processes

Energy Technology Data Exchange (ETDEWEB)

Hermosilla, Daphne, E-mail: dhermosilla@quim.ucm.es [Departamento de Ingenieria Quimica, Facultad de Ciencias Quimicas, Universidad Complutense de Madrid, Ciudad Universitaria s/n, 28040 Madrid (Spain); Cortijo, Manuel [U.D. Operaciones Basicas, Departamento de Ingenieria Forestal, E.T.S.I. Montes, Universidad Politecnica de Madrid, Avda. Ramiro de Maeztu s/n, 28040 Madrid (Spain); Huang, Chin Pao [Department of Civil and Environmental Engineering, 352C DuPont Hall, University of Delaware, Newark, DE 19716 (United States)

2009-05-15

Landfill, a matured and economically appealing technology, is the ultimate approach for the management of municipal solid wastes. However, the inevitable generation of leachate from landfill requires further treatment. Among the various leachate treatment technologies available, advanced oxidation processes (AOPs) are among powerful methods to deal with the refractory organic constituents, and the Fenton reagent has evolved as one promising AOPs for the treatment of leachates. Particularly, the combination of UV-radiation with Fenton's reagent has been reported to be a method that allows both the photo-regeneration of Fe{sup 2+} and photo-decarboxylation of ferric carboxylates. In this study, Fenton and photo-Fenton processes were fine tuned for the treatment of leachates from the Colmenar Viejo (Madrid, Spain) Landfill. Results showed that it is possible to define a set of conditions under which the same COD and TOC removals (approx 70%) could be achieved with both the conventional and photo-Fenton processes. But Fenton process generated an important quantity of iron sludge, which will require further disposal, when performed under optimal COD removal conditions. Furthermore conventional Fenton process was able to achieve slightly over an 80% COD removal from a 'young' leachate, while for 'old' and 'mixed' leachates was close to a 70%. The main advantage showed by the photo-assisted Fenton treatment of landfill leachate was that it consumed 32 times less iron and produced 25 times less sludge volume yielding the same COD removal results than a conventional Fenton treatment.

North American refining

International Nuclear Information System (INIS)

Osten, James; Haltmaier, Susan

2000-01-01

This article examines the current status of the North American refining industry, and considers the North American economy and the growth in demand in the petroleum industry, petroleum product demand and quality, crude oil upgrading to meet product standards, and changes in crude oil feedstocks such as the use of heavier crudes and bitumens. Refining expansion, the declining profits in refining, and changes due to environmental standards are discussed. The Gross Domestic Product and oil demand for the USA, Canada, Mexico, and Venezuela for the years 1995-2020 are tabulated

Process data validation according VDI 2048 in conventional and nuclear power plants

International Nuclear Information System (INIS)

Langenstein, M.; Laipple, B.; Schmid, F.

2004-01-01

Process data validation according VDI 2048 in conventional and nuclear power plants is required for acceptance testing, process and component monitoring, and status-oriented maintenance. Once a validation system like VALI III has been certified according to VDI 2048, power plant owners can use the data obtained for efficiency increase. Further, all control variables can be adjusted so as to ensure maximum plant efficiency. (orig.)

Government will shape China's refining boom

International Nuclear Information System (INIS)

Wang, H.

1995-01-01

China's refining system is undergoing a major overhaul. New refineries are being built as existing ones are upgraded and expanded. The success of refineries funded completely or partially by non-chinese companies will depend in part on Chinese government policy. There will be demand for products from third-party processing facilities, but hard current is necessary for the investors to repatriate profits and for china Petrochemical Corp. (Sinopec) to bid on the products from such facilities. The limited convertibility of chinese current constitutes a major central control over the country's entire economy. This control can be affected by limiting product exchange participants and the volumes to be traded. Such a limitation, however, will reduce access of non-Chinese companies to China's markets, and is not likely to occur in the next 10 years. The paper discusses the current situation in capacity and in refining, capacity, expansion, refinery planning, construction projects, third-party processing, and the prospects for change

Multivariate refined composite multiscale entropy analysis

International Nuclear Information System (INIS)

Humeau-Heurtier, Anne

2016-01-01

Multiscale entropy (MSE) has become a prevailing method to quantify signals complexity. MSE relies on sample entropy. However, MSE may yield imprecise complexity estimation at large scales, because sample entropy does not give precise estimation of entropy when short signals are processed. A refined composite multiscale entropy (RCMSE) has therefore recently been proposed. Nevertheless, RCMSE is for univariate signals only. The simultaneous analysis of multi-channel (multivariate) data often over-performs studies based on univariate signals. We therefore introduce an extension of RCMSE to multivariate data. Applications of multivariate RCMSE to simulated processes reveal its better performances over the standard multivariate MSE. - Highlights: • Multiscale entropy quantifies data complexity but may be inaccurate at large scale. • A refined composite multiscale entropy (RCMSE) has therefore recently been proposed. • Nevertheless, RCMSE is adapted to univariate time series only. • We herein introduce an extension of RCMSE to multivariate data. • It shows better performances than the standard multivariate multiscale entropy.

Decontamination of steel by melt refining: A literature review

International Nuclear Information System (INIS)

Ozturk, B.; Fruehan, R.J.

1994-01-01

It has been reported that a large amount of metal waste is produced annually by nuclear fuel processing and nuclear power plants. These metal wastes are contaminated with radioactive elements, such as uranium and plutonium. Current Department of Energy guidelines require retrievable storage of all metallic wastes containing transuranic elements above a certain level. Because of high cost, it is important to develop an effective decontamination and volume reduction method for low level contaminated metals. It has been shown by some investigators that a melt refining technique can be used for the processing of the contaminated metal wastes. In this process, contaminated metal is melted wit a suitable flux. The radioactive elements are oxidized and transferred to a slag phase. In order to develop a commercial process it is important to have information on the thermodynamics and kinetics of the removal. Therefore, a literature search was carried out to evaluate the available information on the decontamination uranium and transuranic-contaminated plain steel, copper and stainless steel by melt a refining technique. Emphasis was given to the thermodynamics and kinetics of the removal. Data published in the literature indicate that it is possible to reduce the concentration of radioactive elements to a very low level by the melt refining method. 20 refs

40 CFR 80.1142 - What are the provisions for small refiners under the RFS program?

Science.gov (United States)

2010-07-01

... all of the following criteria: (i) The refiner produced gasoline at its refineries by processing crude... Standard § 80.1142 What are the provisions for small refiners under the RFS program? (a)(1) Gasoline produced by a refiner, or foreign refiner (as defined at § 80.1165(a)), is exempt from the renewable fuel...

Production of a 304 stainless steel nuclear reactor forging from a very large electroslag refined ingot

International Nuclear Information System (INIS)

Watkins, E.J.; Tihansky, E.L.

1986-01-01

A four-loop, upper barrel flange forging for a nuclear reactor was produced from what the authors believe to be the largest 304H grade stainless steel electroslag refined (ESR) ingot ever refined. The ingot was refined in a 1524-mm-diameter, ingot withdrawal-type ESR furnace using a lime-bearing slag, low-frequency a-c power, and dry air protection. Five electrodes were remelted in order to produce the desired ingot weight. The ingot was subsequently forged in a five-step operation on a 6800-metric-ton press to produce the desired barrel flange configuration. Testing of the finished machined forging revealed excellent tensile ductility, excellent ultrasonic penetrability, and good chemical uniformity with no macrosegregation. Overall quality was judged to be superior to previously produced, conventionally melted forgings

Grain Refinement of Commercial EC Grade 1070 Aluminium Alloy for Electrical Application

OpenAIRE

Hassanabadi, Massoud

2015-01-01

The aluminium alloys for electrical conductivity applications are generally not grain refinedsince the addition of grain refiners drops the electrical conductivity by introducing impuritiesinto the melt. Non-grain refined aluminium may lead to bar fracture and cracks during themetalworking process. The present study focuses to find an optimum balance between the grain refiner addition andthe electrical conductivity of commercial EC grade 1070 aluminium alloy for electricalapplication. In orde...

Modeling of the inhomogeneity of grain refinement during combined metal forming process by finite element and cellular automata methods

Energy Technology Data Exchange (ETDEWEB)

Majta, Janusz; Madej, Łukasz; Svyetlichnyy, Dmytro S.; Perzyński, Konrad; Kwiecień, Marcin, E-mail: mkwiecie@agh.edu.pl; Muszka, Krzysztof

2016-08-01

The potential of discrete cellular automata technique to predict the grain refinement in wires produced using combined metal forming process is presented and discussed within the paper. The developed combined metal forming process can be treated as one of the Severe Plastic Deformation (SPD) techniques that consists of three different modes of deformation: asymmetric drawing with bending, namely accumulated angular drawing (AAD), wire drawing (WD) and wire flattening (WF). To accurately replicate complex stress state both at macro and micro scales during subsequent deformations two stage modeling approach was used. First, the Finite Element Method (FEM), implemented in commercial ABAQUS software, was applied to simulate entire combined forming process at the macro scale level. Then, based on FEM results, the Cellular Automata (CA) method was applied for simulation of grain refinement at the microstructure level. Data transferred between FEM and CA methods included set of files with strain tensor components obtained from selected integration points in the macro scale model. As a result of CA simulation, detailed information on microstructure evolution during severe plastic deformation conditions was obtained, namely: changes of shape and sizes of modeled representative volume with imposed microstructure, changes of the number of grains, subgrains and dislocation cells, development of grain boundaries angle distribution as well as changes in the pole figures. To evaluate CA model predictive capabilities, results of computer simulation were compared with scanning electron microscopy and electron back scattered diffraction images (SEM/EBSD) studies of samples after AAD+WD+WF process.

The heavy oil refiners needs in the future

International Nuclear Information System (INIS)

Sauer, J.W.

1991-01-01

In the 1970s oil crisis, the high price differential that developed between heavy and light crude led to an expansion in heavy crude processing geared to producing light oil products. The subsequent collapse in prices meant that heavy crudes with low netbacks were shut in, heavy crude refining capacity exceeded the restrained production of heavy crudes, and refineries were operating at losses. However, the low prices for oil rekindled demand and spare production capacity has been absorbed. The crude oil price is forecast to rise to ca $27/bbl by the late 1990s, which is favorable for heavy crude oil production. Nevertheless, investments in heavy crude production are exposed to a high degree of risk. A strategy for dealing with this risk is to integrate into downstream, which makes more sense for heavy crude producers than for conventional producers. On the other hand, such integration is capital-intensive, and light oils will likely be favored in crude oil production developments for the next several years. Low prices for natural gas will make it hard to find markets for residual fuel made from heavy crudes. 8 figs

Refinement of Parallel and Reactive Programs

OpenAIRE

Back, R. J. R.

1992-01-01

We show how to apply the refinement calculus to stepwise refinement of parallel and reactive programs. We use action systems as our basic program model. Action systems are sequential programs which can be implemented in a parallel fashion. Hence refinement calculus methods, originally developed for sequential programs, carry over to the derivation of parallel programs. Refinement of reactive programs is handled by data refinement techniques originally developed for the sequential refinement c...

Creating value in refining

International Nuclear Information System (INIS)

Cobb, C.B.

2001-01-01

This article focuses on recent developments in the US refining industry and presents a model for improving the performance of refineries based on the analysis of the refining industry by Cap Gemini Ernst and Young. The identification of refineries in risk of failing, the construction of pipelines for refinery products from Gulf State refineries, mergers and acquisitions, and poor financial performance are discussed. Current challenges concerning the stagnant demand for refinery products, environmental regulations, and shareholder value are highlighted. The structure of the industry, the creation of value in refining, and the search for business models are examined. The top 25 US companies and US refining business groups are listed

Initiating technical refinements in high-level golfers: Evidence for contradictory procedures.

Science.gov (United States)

Carson, Howie J; Collins, Dave; Richards, Jim

2016-01-01

When developing motor skills there are several outcomes available to an athlete depending on their skill status and needs. Whereas the skill acquisition and performance literature is abundant, an under-researched outcome relates to the refinement of already acquired and well-established skills. Contrary to current recommendations for athletes to employ an external focus of attention and a representative practice design,  Carson and  Collins' (2011) [Refining and regaining skills in fixation/diversification stage performers: The Five-A Model. International Review of Sport and Exercise Psychology, 4, 146-167. doi: 10.1080/1750984x.2011.613682 ] Five-A Model requires an initial narrowed internal focus on the technical aspect needing refinement: the implication being that environments which limit external sources of information would be beneficial to achieving this task. Therefore, the purpose of this paper was to (1) provide a literature-based explanation for why techniques counter to current recommendations may be (temporarily) appropriate within the skill refinement process and (2) provide empirical evidence for such efficacy. Kinematic data and self-perception reports are provided from high-level golfers attempting to consciously initiate technical refinements while executing shots onto a driving range and into a close proximity net (i.e. with limited knowledge of results). It was hypothesised that greater control over intended refinements would occur when environmental stimuli were reduced in the most unrepresentative practice condition (i.e. hitting into a net). Results confirmed this, as evidenced by reduced intra-individual movement variability for all participants' individual refinements, despite little or no difference in mental effort reported. This research offers coaches guidance when working with performers who may find conscious recall difficult during the skill refinement process.

Architectural Refinement for the Design of Survivable Systems

National Research Council Canada - National Science Library

Ellison, Robert

2001-01-01

...; that is, have no central administration and no unified security policy. The survivable architecture refinement is an iterative risk-driven process which adopts the structure of Boehm's Spiral Model Boehm 88...

Geometry Processing of Conventionally Produced Mouse Brain Slice Images.

Science.gov (United States)

Agarwal, Nitin; Xu, Xiangmin; Gopi, M

2018-04-21

Brain mapping research in most neuroanatomical laboratories relies on conventional processing techniques, which often introduce histological artifacts such as tissue tears and tissue loss. In this paper we present techniques and algorithms for automatic registration and 3D reconstruction of conventionally produced mouse brain slices in a standardized atlas space. This is achieved first by constructing a virtual 3D mouse brain model from annotated slices of Allen Reference Atlas (ARA). Virtual re-slicing of the reconstructed model generates ARA-based slice images corresponding to the microscopic images of histological brain sections. These image pairs are aligned using a geometric approach through contour images. Histological artifacts in the microscopic images are detected and removed using Constrained Delaunay Triangulation before performing global alignment. Finally, non-linear registration is performed by solving Laplace's equation with Dirichlet boundary conditions. Our methods provide significant improvements over previously reported registration techniques for the tested slices in 3D space, especially on slices with significant histological artifacts. Further, as one of the application we count the number of neurons in various anatomical regions using a dataset of 51 microscopic slices from a single mouse brain. To the best of our knowledge the presented work is the first that automatically registers both clean as well as highly damaged high-resolutions histological slices of mouse brain to a 3D annotated reference atlas space. This work represents a significant contribution to this subfield of neuroscience as it provides tools to neuroanatomist for analyzing and processing histological data. Copyright © 2018 Elsevier B.V. All rights reserved.

Unilever food safety assurance system for refined vegetable oils and fats

Directory of Open Access Journals (Sweden)

van Duijn Gerrit

2010-03-01

Full Text Available The Unilever Food Safety Assurance system for refined oils and fats is based on risk assessments for the presence of contaminants or pesticide residues in crude oils, and refining process studies to validate the removal of these components. Crude oil risk assessments were carried out by combining supply chain visits, and analyses of the contaminant and pesticide residue levels in a large number of crude oil samples. Contaminants like poly-aromatic hydrocarbons and hydrocarbons of mineral origin, and pesticide residues can largely be removed by refining. For many years, this Food Safety Assurance System has proven to be effective in controlling contaminant levels in refined vegetable oils and fats.

Kinetics of Sub-Micron Grain Size Refinement in 9310 Steel

Science.gov (United States)

Kozmel, Thomas; Chen, Edward Y.; Chen, Charlie C.; Tin, Sammy

2014-05-01

Recent efforts have focused on the development of novel manufacturing processes capable of producing microstructures dominated by sub-micron grains. For structural applications, grain refinement has been shown to enhance mechanical properties such as strength, fatigue resistance, and fracture toughness. Through control of the thermo-mechanical processing parameters, dynamic recrystallization mechanisms were used to produce microstructures consisting of sub-micron grains in 9310 steel. Starting with initial bainitic grain sizes of 40 to 50 μm, various levels of grain refinement were observed following hot deformation of 9310 steel samples at temperatures and strain rates ranging from 755 K to 922 K (482 °C and 649 °C) and 1 to 0.001/s, respectively. The resulting deformation microstructures were characterized using scanning electron microscopy and electron backscatter diffraction techniques to quantify the extent of carbide coarsening and grain refinement occurring during deformation. Microstructural models based on the Zener-Holloman parameter were developed and modified to include the effect of the ferrite/carbide interactions within the system. These models were shown to effectively correlate microstructural attributes to the thermal mechanical processing parameters.

Modelling of the Effectiveness of Al-Ti-B Refiners in Commercial Purity Aluminium

Science.gov (United States)

Bunn, A. M.; Evans, P. V.; Bristow, D. J.; Greer, A. L.

Al-5Ti-1B (wt.%) alloys are effective grain refiners for DC-cast aluminium although as few as 1% of the TiB2 particles added to the melt nucleate grains. The aim of this work is to develop quantitative modelling for prediction of grain sizes in commercial purity aluminium. In this way the low efficiency of refiners can be understood, ultimately to clarify the design rules for a more effective refiner. The modelling focuses on the role of particle size distribution. This is in conjunction with measurements (by scanning electron microscopy and image analysis) of the particle size distributions in commercial Al-5Ti-1B refiners known to have differing performances. The undercooling required for heterogeneous nucleation of oc-Al on the surface of potent TiB2 particles is extremely low. Accordingly, the modelling is based on the assumption that the critical step for a particle to behave as an active growth centre is that required to initiate free growth from the particle surface, rather than the initial heterogeneous nucleation event. It is considered that further initiation of free growth of crystals is stopped by the onset of recalescence in the melt during solidification. Only those particles which are active growth centres at the point of recalescence will contribute towards the final grain size. Negligible interference between particles and spherical growth up to the point of recalescence are assumed; these assumptions are rigorously tested. The model tests the effect of varying the particle size distribution by using measured distributions from `good' and `poor' refiners. The variation of grain size with addition rate of refiner is examined. The model predicts an effective saturation, beyond which further addition has little effect. In general, good agreement is found between the grain-size predictions and conventional grain-refining tests.

Optimization of breast reconstruction results using TMG flap in 30 cases: Evaluation of several refinements addressing flap design, shaping techniques, and reduction of donor site morbidity.

Science.gov (United States)

Nickl, Stefanie; Nedomansky, Jakob; Radtke, Christine; Haslik, Werner; Schroegendorfer, Klaus F

2018-01-31

The transverse myocutaneous gracilis (TMG) flap is a widely used alternative to abdominal flaps in autologous breast reconstruction. However, secondary procedures for aesthetic refinement are frequently necessary. Herein, we present our experience with an optimized approach in TMG breast reconstruction to enhance aesthetic outcome and to reduce the need for secondary refinements. We retrospectively analyzed 37 immediate or delayed reconstructions with TMG flaps in 34 women, performed between 2009 and 2015. Four patients (5 flaps) constituted the conventional group (non-optimized approach). Thirty patients (32 flaps; modified group) underwent an optimized procedure consisting of modified flap harvesting and shaping techniques and methods utilized to reduce denting after rib resection and to diminish donor site morbidity. Statistically significant fewer secondary procedures (0.6 ± 0.9 versus 4.8 ± 2.2; P < .001) and fewer trips to the OR (0.4 ± 0.7 versus 2.3 ± 1.0 times; P = .001) for aesthetic refinement were needed in the modified group as compared to the conventional group. In the modified group, 4 patients (13.3%) required refinement of the reconstructed breast, 7 patients (23.3%) underwent mastopexy/mammoplasty or lipofilling of the contralateral breast, and 4 patients (13.3%) required refinement of the contralateral thigh. Total flap loss did not occur in any patient. Revision surgery was needed once. Compared to the conventional group, enhanced aesthetic results with consecutive reduction of secondary refinements could be achieved when using our modified flap harvesting and shaping techniques, as well as our methods for reducing contour deformities after rib resection and for overcoming donor site morbidities. © 2017 Wiley Periodicals, Inc.

Southeast Asian oil markets and refining

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, N.D. [FACTS, Inc., Honolulu, Hawaii (United States)

1999-09-01

An overview of the Southeast Asian oil markets and refining is presented concentrating on Brunei, Malaysia, the Philippines, Singapore and Thailand refiners. Key statistics of the refiners in this region are tabulated. The demand and the quality of Indonesian, Malaysian, Philippine, Singapore and Thai petroleum products are analysed. Crude distillation unit capacity trends in the Southeastern Asian refining industry are discussed along with cracking to distillation ratios, refining in these countries, and the impact of changes in demand and refining on the product trade.

Southeast Asian oil markets and refining

International Nuclear Information System (INIS)

Yamaguchi, N.D.

1999-01-01

An overview of the Southeast Asian oil markets and refining is presented concentrating on Brunei, Malaysia, the Philippines, Singapore and Thailand refiners. Key statistics of the refiners in this region are tabulated. The demand and the quality of Indonesian, Malaysian, Philippine, Singapore and Thai petroleum products are analysed. Crude distillation unit capacity trends in the Southeastern Asian refining industry are discussed along with cracking to distillation ratios, refining in these countries, and the impact of changes in demand and refining on the product trade

Replication, refinement & reachability: complexity in dynamic condition-response graphs

DEFF Research Database (Denmark)

Debois, Søren; Hildebrandt, Thomas T.; Slaats, Tijs

2017-01-01

We explore the complexity of reachability and run-time refinement under safety and liveness constraints in event-based process models. Our study is framed in the DCR? process language, which supports modular specification through a compositional operational semantics. DCR? encompasses the “Dynami...

Significance of Kaduna River to Kaduna Refining and ...

African Journals Online (AJOL)

User

River through the Kaduna Refining and Petrochemicals Company (KRPC) plants and .... Other less-common process involves filtering heated crude using diatomaceous earth ..... Water is polluted by the fallout from air pollution and by refinery.

A refined approach: Saudi Arabia moves beyond crude

International Nuclear Information System (INIS)

Krane, Jim

2015-01-01

Saudi Arabia's role in global energy markets is changing. The kingdom is reshaping itself as a supplier of refined petroleum products while moving beyond its long-held role as a simple exporter of crude oil. This change is commensurate with the typical development trajectory of a state progressing to a more advanced stage of global economic integration. Gains from increased refining include reducing fuel imports and capturing margins now bequeathed to competitors. Refining also allows the kingdom to export its heavy crude oil to a wider array of customers, beyond select importers configured to handle heavy crudes. However, the move also presents strategic complications. The world's 'swing supplier' of oil may grow less willing or able to adjust supply to suit market demands. In the process, Saudi Arabia may have to update the old “oil for security” relationship that links it with Washington, augmenting it with a more diverse set of economic and investment ties with individual companies and countries, including China. -- Highlights: •Saudi Arabia is diverting crude oil into an expanding refining sector. •In doing so, the kingdom is moving beyond its role as global “swing supplier” of crude oil. •The kingdom will benefit from increased refining, including enhanced demand for heavy crude. •Strategic complications may force it to seek security partners beyond Washington

Linearly Refined Session Types

Directory of Open Access Journals (Sweden)

Pedro Baltazar

2012-11-01

Full Text Available Session types capture precise protocol structure in concurrent programming, but do not specify properties of the exchanged values beyond their basic type. Refinement types are a form of dependent types that can address this limitation, combining types with logical formulae that may refer to program values and can constrain types using arbitrary predicates. We present a pi calculus with assume and assert operations, typed using a session discipline that incorporates refinement formulae written in a fragment of Multiplicative Linear Logic. Our original combination of session and refinement types, together with the well established benefits of linearity, allows very fine-grained specifications of communication protocols in which refinement formulae are treated as logical resources rather than persistent truths.

Region-of-interest volumetric visual hull refinement

KAUST Repository

Knoblauch, Daniel

2010-01-01

This paper introduces a region-of-interest visual hull refinement technique, based on flexible voxel grids for volumetric visual hull reconstructions. Region-of-interest refinement is based on a multipass process, beginning with a focussed visual hull reconstruction, resulting in a first 3D approximation of the target, followed by a region-of-interest estimation, tasked with identifying features of interest, which in turn are used to locally refine the voxel grid and extract a higher-resolution surface representation for those regions. This approach is illustrated for the reconstruction of avatars for use in tele-immersion environments, where head and hand regions are of higher interest. To allow reproducability and direct comparison a publicly available data set for human visual hull reconstruction is used. This paper shows that region-of-interest reconstruction of the target is faster and visually comparable to higher resolution focused visual hull reconstructions. This approach reduces the amount of data generated through the reconstruction, allowing faster post processing, as rendering or networking of the surface voxels. Reconstruction speeds support smooth interactions between the avatar and the virtual environment, while the improved resolution of its facial region and hands creates a higher-degree of immersion and potentially impacts the perception of body language, facial expressions and eye-to-eye contact. Copyright © 2010 by the Association for Computing Machinery, Inc.

Conventional and Innovative Processing of Milk for Yogurt Manufacture; Development of Texture and Flavor: A Review

Directory of Open Access Journals (Sweden)

Panagiotis Sfakianakis

2014-03-01

Full Text Available Milk and yogurt are important elements of the human diet, due to their high nutritional value and their appealing sensory properties. During milk processing (homogenization, pasteurization and further yogurt manufacture (fermentation physicochemical changes occur that affect the flavor and texture of these products while the development of standardized processes contributes to the development of desirable textural and flavor characteristics. The processes that take place during milk processing and yogurt manufacture with conventional industrial methods, as well as with innovative methods currently proposed (ultra-high pressure, ultrasound, microfluidization, pulsed electric fields, and their effect on the texture and flavor of the final conventional or probiotic/prebiotic products will be presented in this review.

Conventional and Innovative Processing of Milk for Yogurt Manufacture; Development of Texture and Flavor: A Review

Science.gov (United States)

Sfakianakis, Panagiotis; Tzia, Constatnina

2014-01-01

Milk and yogurt are important elements of the human diet, due to their high nutritional value and their appealing sensory properties. During milk processing (homogenization, pasteurization) and further yogurt manufacture (fermentation) physicochemical changes occur that affect the flavor and texture of these products while the development of standardized processes contributes to the development of desirable textural and flavor characteristics. The processes that take place during milk processing and yogurt manufacture with conventional industrial methods, as well as with innovative methods currently proposed (ultra-high pressure, ultrasound, microfluidization, pulsed electric fields), and their effect on the texture and flavor of the final conventional or probiotic/prebiotic products will be presented in this review. PMID:28234312

Bauxite Mining and Alumina Refining

OpenAIRE

Donoghue, A. Michael; Frisch, Neale; Olney, David

2014-01-01

Objective: To describe bauxite mining and alumina refining processes and to outline the relevant physical, chemical, biological, ergonomic, and psychosocial health risks. Methods: Review article. Results: The most important risks relate to noise, ergonomics, trauma, and caustic soda splashes of the skin/eyes. Other risks of note relate to fatigue, heat, and solar ultraviolet and for some operations tropical diseases, venomous/dangerous animals, and remote locations. Exposures to bauxite dust,...

Protein NMR Structures Refined with Rosetta Have Higher Accuracy Relative to Corresponding X-ray Crystal Structures

Science.gov (United States)

2014-01-01

We have found that refinement of protein NMR structures using Rosetta with experimental NMR restraints yields more accurate protein NMR structures than those that have been deposited in the PDB using standard refinement protocols. Using 40 pairs of NMR and X-ray crystal structures determined by the Northeast Structural Genomics Consortium, for proteins ranging in size from 5–22 kDa, restrained Rosetta refined structures fit better to the raw experimental data, are in better agreement with their X-ray counterparts, and have better phasing power compared to conventionally determined NMR structures. For 37 proteins for which NMR ensembles were available and which had similar structures in solution and in the crystal, all of the restrained Rosetta refined NMR structures were sufficiently accurate to be used for solving the corresponding X-ray crystal structures by molecular replacement. The protocol for restrained refinement of protein NMR structures was also compared with restrained CS-Rosetta calculations. For proteins smaller than 10 kDa, restrained CS-Rosetta, starting from extended conformations, provides slightly more accurate structures, while for proteins in the size range of 10–25 kDa the less CPU intensive restrained Rosetta refinement protocols provided equally or more accurate structures. The restrained Rosetta protocols described here can improve the accuracy of protein NMR structures and should find broad and general for studies of protein structure and function. PMID:24392845

Cross-band noise model refinement for transform domain Wyner–Ziv video coding

DEFF Research Database (Denmark)

Huang, Xin; Forchhammer, Søren

2012-01-01

TDWZ video coding trails that of conventional video coding solutions, mainly due to the quality of side information, inaccurate noise modeling and loss in the final coding step. The major goal of this paper is to enhance the accuracy of the noise modeling, which is one of the most important aspects...... influencing the coding performance of DVC. A TDWZ video decoder with a novel cross-band based adaptive noise model is proposed, and a noise residue refinement scheme is introduced to successively update the estimated noise residue for noise modeling after each bit-plane. Experimental results show...... that the proposed noise model and noise residue refinement scheme can improve the rate-distortion (RD) performance of TDWZ video coding significantly. The quality of the side information modeling is also evaluated by a measure of the ideal code length....

Control of Refining Processes on Mid-Distillates by Near Infrared Spectroscopy

Directory of Open Access Journals (Sweden)

Zanier-Szydlowski N.

1999-07-01

Full Text Available The purpose of this paper is to demonstrate the accuracy of physicochemical determinations based on equations calculated by multivariate analysis of near infrared spectra which gives access to simultaneous analyses both on-line and off-line. Detailed results concerning the determination of the refractive index at 20°C, the density, the weight% of hydrogen, the % of aromatic carbon, the weight% of mono-, di- and total aromatics and the cetane number on mid-distillates are given in a shorter time than using the conventional approach by standardized methods. It is shown that near infrared spectroscopy combined with chemometrics should allow detailed and precise comparisons of the hydrotreatment process efficiencies.

Drugs Cleared Through The FDA's Expedited Review Offer Greater Gains Than Drugs Approved By Conventional Process.

Science.gov (United States)

Chambers, James D; Thorat, Teja; Wilkinson, Colby L; Neumann, Peter J

2017-08-01

We investigated whether drugs approved by the Food and Drug Administration (FDA) through expedited review have offered larger health gains, compared to drugs approved through conventional review processes. We identified published estimates of additional health gains (measured in quality-adjusted life-years, or QALYs) associated with drugs approved in the period 1999-2012 through expedited (seventy-six drugs) versus conventional (fifty-nine) review processes. We found that drugs in at least one expedited review program offered greater gains than drugs reviewed through conventional processes (0.182 versus 0.003 QALYs). We also found that, compared to drugs not included in the same program, greater gains were provided by drugs in the priority review (0.175 versus 0.007 QALYs), accelerated approval (0.370 versus 0.031 QALYs), and fast track (0.254 versus 0.014 QALYs) programs. Our analysis suggests that the FDA has prioritized drugs that offer the largest health gains. Project HOPE—The People-to-People Health Foundation, Inc.

Biodesulfurization process evaluation with a Gordona rubropertinctus strain

International Nuclear Information System (INIS)

Acero, Julia; Verdugo, Claudia; Mogollon Leonardo

2003-01-01

Direct combustion of fossil fuels produce sulfur oxides, which are the main source of acid rain; therefore, most countries worldwide are regulating its release into the environment. As a consequence, several processes have been developed over the past years for desulfurization of crude oil and distillates. Due to its specificity, biodesulfurization is an interesting alternative for the transformation and upgrading of refined products, acting as a complement to traditional refining processes. This work presents an overview of Ecopetrol - Instituto Colombiano del Petroleo (ICP) efforts to develop a Biodesulfurization process, based on the activity of a native strain of Gordona rubropertinctus ICP172. Technical improvements on the isolation and characterization of desulfurizing microorganisms, the potential of developing new biocatalysts by means of directed evolution techniques, as well as the experience achieved during production of the biocatalyst in large-scale fermentation processes are hereby presented. The results of biodesulfurization reactions in conventional reactors and in a new membrane bioreactor prototype are also included. Finally, technological challenges faced by biodesulfurization processes are also discussed

Future prospects for palm oil refining and modifications

Directory of Open Access Journals (Sweden)

Gibon Véronique

2009-07-01

Full Text Available Palm oil is rich in minor components that impart unique nutritional properties and need to be preserved. In this context, refining technologies have been improved, with the dual temperature deodorizer, the double condensing unit and the ice condensing system. The DOBI is a good tool to assess quality of the crude palm oil and its ability to be properly refined. Specially refined oils open a market for new high quality products (golden palm oil, red palm oil, white soaps, etc.. Palm oil is a good candidate for the multi-step dry fractionation process, aiming to the production of commodity oils and specialty fats (cocoa butter replacers. New technological developments allow quality and yield improvements. Palm oil and fractions are also valuable feedstock for enzymatic interesterification in which applications are for commodity oil (low-trans margarines and shortenings and for special products (cocoa butter equivalents, infant formulation, ….

Changing perspective on tissue processing - comparison of microwave histoprocessing method with the conventional method

Directory of Open Access Journals (Sweden)

G Shrestha

2015-09-01

Full Text Available Background: Histopathological examination of tissues requires sliver of formalin fixed tissue that has been chemically processed and then stained with Haematoxylin and Eosin. The time honored conventional method of tissue processing, which requires 12 to 13 hours for completion, is employed at majority of laboratories but is now seeing the

Commercial refining in the Mediterranean

International Nuclear Information System (INIS)

Packer, P.

1999-01-01

About 9% of the world's oil refining capacity is on the Mediterranean: some of the world's biggest and most advanced refineries are on Sicily and Sardinia. The Mediterranean refineries are important suppliers to southern Europe and N. Africa. The article discusses commercial refining in the Mediterranean under the headings of (i) historic development, (ii) product demand, (iii) refinery configurations, (iv) refined product trade, (v) financial performance and (vi) future outlook. Although some difficulties are foreseen, refining in the Mediterranean is likely to continue to be important well into the 21st century. (UK)

Effects of degumming on biodiesel properties of some non-conventional seedoils

Directory of Open Access Journals (Sweden)

Abolanle Saheed Adekunle

2016-11-01

Full Text Available This study examined the effect of degumming process on physicochemical and biodiesel properties of six non-conventional oils in Nigeria extracted from the seeds and flesh of Terminalia catappa (seed, Irvingia gabonesis (seed, Glycine max (seed, Persea americana(flesh, Tithonia diversifolia (seed, and Dacryodes edulis(flesh. The fruits and seeds were air-dried to constant weight and pulverized. Oil was extracted from the milled sample using Soxhlet extraction method. The oils were degummed using 300 μg/mL of NaCl solution to obtain the refined (degummed oil. Physicochemical properties of both degummed and crude oils were carried out using the AOAC (1990 methods. The fuel properties of the biodiesel obtained were carried out using ASTM methods. Results showed that degumming process lead to high biodiesel yield and reduced the acid value and iodine value compared with the crude oils. The study therefore concluded that degummed oils were a better substitute for biodiesel fuels production.

Role of manganese on the grain refining efficiency of AZ91D magnesium alloy refined by Al4C3

International Nuclear Information System (INIS)

Liu Shengfa; Zhang Yuan; Han Hui

2010-01-01

A novel Mg-50% Al 4 C 3 (hereafter in wt.%) master alloy has been developed by powder in situ synthesis process, the role of manganese on the grain refining efficiency of AZ91D magnesium alloy refined by this master alloy has been investigated. X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDS) results show the existence of Al 4 C 3 particles in this master alloy. After addition of 0.6% Al 4 C 3 or combined addition of 0.6% Al 4 C 3 and 0.27% Mn, the average grain size of AZ91D decreased dramatically from 360 μm to 210 μm, and from 360 μm to130 μm, respectively. However, no further refinement of grain size was achieved with additional amount of Mn exceeding 0.27% for AZ91D alloy refined by 0.6% Al 4 C 3 in the present investigation. Al-C-O-Mn-Fe-rich intermetallic particles with an Al-C-O-rich coating film, often observed in the central region of magnesium grains of the AZ91D alloy treated by the combination of Al 4 C 3 and Mn, are proposed to be the potent nucleating substrates for primary α-Mg.

Preparation of refined oils, etc

Energy Technology Data Exchange (ETDEWEB)

1931-02-03

A process is disclosed for the preparation of refined sulfur-containing oils from sulfur-containing crude oils obtained by distillation of bituminous limestone, characterized by this crude oil being first subjected to a purification by distillation with steam in the known way, then treated with lime and chloride of lime and distilled preferably in the presence of zinc powder, whereby in this purification a rectification can be added for the purpose of recovering definite fractions.

Anomalies in the refinement of isoleucine

International Nuclear Information System (INIS)

Berntsen, Karen R. M.; Vriend, Gert

2014-01-01

The side-chain torsion angles of isoleucines in X-ray protein structures are a function of resolution, secondary structure and refinement software. Detailing the standard torsion angles used in refinement software can improve protein structure refinement. A study of isoleucines in protein structures solved using X-ray crystallography revealed a series of systematic trends for the two side-chain torsion angles χ 1 and χ 2 dependent on the resolution, secondary structure and refinement software used. The average torsion angles for the nine rotamers were similar in high-resolution structures solved using either the REFMAC, CNS or PHENIX software. However, at low resolution these programs often refine towards somewhat different χ 1 and χ 2 values. Small systematic differences can be observed between refinement software that uses molecular dynamics-type energy terms (for example CNS) and software that does not use these terms (for example REFMAC). Detailing the standard torsion angles used in refinement software can improve the refinement of protein structures. The target values in the molecular dynamics-type energy functions can also be improved

Anomalies in the refinement of isoleucine

Energy Technology Data Exchange (ETDEWEB)

Berntsen, Karen R. M.; Vriend, Gert, E-mail: gerrit.vriend@radboudumc.nl [Radboud University Medical Center, Geert Grooteplein 26-28, 6525 GA Nijmegen (Netherlands)

2014-04-01

The side-chain torsion angles of isoleucines in X-ray protein structures are a function of resolution, secondary structure and refinement software. Detailing the standard torsion angles used in refinement software can improve protein structure refinement. A study of isoleucines in protein structures solved using X-ray crystallography revealed a series of systematic trends for the two side-chain torsion angles χ{sub 1} and χ{sub 2} dependent on the resolution, secondary structure and refinement software used. The average torsion angles for the nine rotamers were similar in high-resolution structures solved using either the REFMAC, CNS or PHENIX software. However, at low resolution these programs often refine towards somewhat different χ{sub 1} and χ{sub 2} values. Small systematic differences can be observed between refinement software that uses molecular dynamics-type energy terms (for example CNS) and software that does not use these terms (for example REFMAC). Detailing the standard torsion angles used in refinement software can improve the refinement of protein structures. The target values in the molecular dynamics-type energy functions can also be improved.

Electromagnetic Stirring versus ECAP: Morphological Comparison of Al-Si-Cu Alloys to Make the Microstructural Refinement for Use in SSM Processing

Directory of Open Access Journals (Sweden)

Luis Vanderlei Torres

2016-01-01

Full Text Available This work evaluates the morphological evolution at the semisolid state of the Al-4.0wt%Si-2.5wt%Cu alloy produced by direct chill casting under electromagnetic stirring (EMS and by one equal channel angular pressing (ECAP pass. The ECAP emerged as a promising technique capable of reduction and homogeneous metals microstructure imposing large deformations occurs in a matrix that contains two channels of the same cross-sectional area and forms an angle of 120°. The materials were submitted to reheating treatment in condition of 60% solid fraction at treatment times of 0, 30, and 90 s. Comparing the two cases, we have the presented ECAP process that had an excellent response to the recovery and recrystallization mechanisms, and refined microstructures ideal for thixoforming were produced. Primary particle sizes of about 45 μm and grain sizes of about 75 μm and a circularity shape factor of more than 0.60 were obtained. The low silicon alloy, Al-4.0wt%Si-2.5wt%Cu, presented excellent refinement when processed via equal channel angular pressing, presenting good morphological stability at the semisolid state, without significant changes in size or shape of the solid particles. This fully globular structure is favourable for thixoforming processes.

Effect of the strain-induced melt activation (SIMA) process on the tensile properties of a new developed super high strength aluminum alloy modified by Al-5Ti-1B grain refiner

Energy Technology Data Exchange (ETDEWEB)

Haghparast, Amin [School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Nourimotlagh, Masoud [Young Researchers Club, Dareshahr Branch, Islamic Azad university (Iran, Islamic Republic of); Alipour, Mohammad, E-mail: Alipourmo@ut.ac.ir [School of Metallurgy and Materials Engineering, University of Tehran, Tehran (Iran, Islamic Republic of)

2012-09-15

In this study, the effect of Al-5Ti-1B grain refiners and modified strain-induced melt activation process on an Al-Zn-Mg-Cu alloy was studied. The optimum level of Ti was found to be 0.1 wt.%. The specimens subjected to deformation ratio of 40% (at 300 Degree-Sign C) and various heat treatment times (10-40 min) and temperature (550-600 Degree-Sign C) regimes were characterized in this study. Reheating condition to obtain a fine globular microstructure was optimized. Microstructural examinations were conducted by optical and scanning electron microscopy coupled with an energy dispersive spectrometry. The optimum temperature and time in strain-induced melt activation process are 575 Degree-Sign C and 20 min, respectively. T6 heat treatment including quenching to room temperature and aging at 120 Degree-Sign C for 24 h was employed to reach to the maximum strength. Significant improvements in mechanical properties were obtained with the addition of grain refiner combined with T6 heat treatment. After the T6 heat treatment, the average tensile strength increased from 283 MPa to 587 and 332 MPa to 617 for samples refined with 2 wt.% Al-5Ti-1B before and after strain-induced melt activation process and extrusion process, respectively. Ultimate strength of Ti-refined specimens without SIMA process has a lower value than globular microstructure specimens after SIMA and extrusion process. - Highlights: Black-Right-Pointing-Pointer The effect of Al-5Ti-1B on the aluminum alloy produced by SIMA process was studied. Black-Right-Pointing-Pointer Al-5Ti-1B is an effective in reducing the grain and reagent fine microstructure. Black-Right-Pointing-Pointer Reheating condition to obtain a fine globular microstructure was optimized. Black-Right-Pointing-Pointer The optimum temperature and time in SIMA process are 575 Degree-Sign C and 20 min respectively. Black-Right-Pointing-Pointer UTS of globular structure specimens have a more value than Ti-refined specimens.

Structural heredity of TiC and its influences on refinement behaviors of AlTiC master alloy

Institute of Scientific and Technical Information of China (English)

王振卿; 刘相法; 柳延辉; 张均燕; 于丽娜; 边秀房

2003-01-01

Heredity of microstructure in AlTiC master alloy, grain refiners, was analyzed. It is found that, for morphologies and distributions of TiC particles, there are visible heredity which originates from raw materials or processing methods of Al melt, and will ultimately be transferred to the solid state structure through the melt stage, and this phenomenon can cause hereditary influences on refinement: formation of chain-like TiC morphology results in rapid refinement fading behavior; distribution of TiC along grain boundaries greatly reduces refinement efficiency. Controlling of structural heredity through proper selections of raw materials and processing parameters is of great importance in obtaining ideal microstructures and improving refinement behaviors of AlTiC master alloys.

TiO2-coated mesoporous carbon: conventional vs. microwave-annealing process.

Science.gov (United States)

Coromelci-Pastravanu, Cristina; Ignat, Maria; Popovici, Evelini; Harabagiu, Valeria

2014-08-15

The study of coating mesoporous carbon materials with titanium oxide nanoparticles is now becoming a promising and challenging area of research. To optimize the use of carbon materials in various applications, it is necessary to attach functional groups or other nanostructures to their surface. The combination of the distinctive properties of mesoporous carbon materials and titanium oxide is expected to be applied in field emission displays, nanoelectronic devices, novel catalysts, and polymer or ceramic reinforcement. But, their synthesis is still largely based on conventional techniques, such as wet impregnation followed by chemical reduction of the metal nanoparticle precursors, which takes time and money. The thermal heating based techniques are time consuming and often lack control of particle size and morphology. Hence, since there is a growing interest in microwave technology, an alternative way of power input into chemical reactions through dielectric heating is the use of microwaves. This work is focused on the advantages of microwave-assisted synthesis of TiO2-coated mesoporous carbon over conventional thermal heating method. The reviewed studies showed that the microwave-assisted synthesis of such composites allows processes to be completed within a shorter reaction time allowing the nanoparticles formation with superior properties than that obtained by conventional method. Copyright © 2014 Elsevier B.V. All rights reserved.

Refining and petrochemicals

Energy Technology Data Exchange (ETDEWEB)

Constancio, Silva

2006-07-01

In 2004, refining margins showed a clear improvement that persisted throughout the first three quarters of 2005. This enabled oil companies to post significantly higher earnings for their refining activity in 2004 compared to 2003, with the results of the first half of 2005 confirming this trend. As for petrochemicals, despite a steady rise in the naphtha price, higher cash margins enabled a turnaround in 2004 as well as a clear improvement in oil company financial performance that should continue in 2005, judging by the net income figures reported for the first half-year. Despite this favorable business environment, capital expenditure in refining and petrochemicals remained at a low level, especially investment in new capacity, but a number of projects are being planned for the next five years. (author)

Refining and petrochemicals

International Nuclear Information System (INIS)

Constancio, Silva

2006-01-01

In 2004, refining margins showed a clear improvement that persisted throughout the first three quarters of 2005. This enabled oil companies to post significantly higher earnings for their refining activity in 2004 compared to 2003, with the results of the first half of 2005 confirming this trend. As for petrochemicals, despite a steady rise in the naphtha price, higher cash margins enabled a turnaround in 2004 as well as a clear improvement in oil company financial performance that should continue in 2005, judging by the net income figures reported for the first half-year. Despite this favorable business environment, capital expenditure in refining and petrochemicals remained at a low level, especially investment in new capacity, but a number of projects are being planned for the next five years. (author)

File: non conventional hydrocarbons - Between concerns and opportunities

International Nuclear Information System (INIS)

Deflandre, Jean-Pierre; Heidmann, Jean-Claude; Vially, Roland; Duflot, Sylvie; Lions, Renaud; Speirs, Julie; Bauquis, Pierre-Rene; Brunelle, Nathalie

2015-01-01

A first article proposes an overview of gas and oil resources with respect to their geological context. The authors address the origins of hydrocarbons, their underground migration and possible trapping, thus scanning the whole spectrum of conventional and non conventional resources. A second article, signed by representatives of companies working on shale gas in Europe as well as in the USA, examines whether the development of shale gases, if it ever emerges in Europe, will be the same as it is in the USA. They notably outline differences regarding several legal aspects on land property and on the environment. Based on a study on shale supply chain which identified costs, needed skills, existing capabilities, and recommendations for closing identified gaps, the third article discusses the perspective and opportunity of a possible development of shale gas in the UK. The fourth article discusses the impacts of the exploitation of source rock oils and gases on the American and World economies, and the fifth one discusses the perspectives for the petrochemicals and refining industries in a context of development of shale gases and oils in the USA, of an over-capacity situation for the refining industry, of decline of the European oil product market, and of competition with new polymer production capacities (notably in the Middle East where ethane extracted from natural gas is available in large quantities and at very low prices)

An assessment of dietary exposure to glyphosate using refined deterministic and probabilistic methods.

Science.gov (United States)

Stephenson, C L; Harris, C A

2016-09-01

Glyphosate is a herbicide used to control broad-leaved weeds. Some uses of glyphosate in crop production can lead to residues of the active substance and related metabolites in food. This paper uses data on residue levels, processing information and consumption patterns, to assess theoretical lifetime dietary exposure to glyphosate. Initial estimates were made assuming exposure to the highest permitted residue levels in foods. These intakes were then refined using median residue levels from trials, processing information, and monitoring data to achieve a more realistic estimate of exposure. Estimates were made using deterministic and probabilistic methods. Exposures were compared to the acceptable daily intake (ADI)-the amount of a substance that can be consumed daily without an appreciable health risk. Refined deterministic intakes for all consumers were at or below 2.1% of the ADI. Variations were due to cultural differences in consumption patterns and the level of aggregation of the dietary information in calculation models, which allows refinements for processing. Probabilistic exposure estimates ranged from 0.03% to 0.90% of the ADI, depending on whether optimistic or pessimistic assumptions were made in the calculations. Additional refinements would be possible if further data on processing and from residues monitoring programmes were available. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

The Canadian refining Industry : The circle of influence

International Nuclear Information System (INIS)

Burton, W.R.

1998-01-01

Examples of how the downstream petroleum industry is influenced by events in the upstream petroleum sector were presented. In order to survive, Canadian refiners (downstream petroleum) must remain competitive with their domestic counterparts, with the U.S. and with offshore refiners who can import products into key Eastern markets. The downstream sector has little choice but to focus on crude costs and flexibility to try to improve the profitability of its operations. In Canada, the supply of both conventional and bitumen crude oil has increased significantly. This change in the supply and demand balance has had a definite impact on prices. Ample Canadian heavy crude supply has caused refiners to adjust their operations to take advantage of lower-cost crude oil. The result has been the announcement of several large-scale projects, such as for example Shell Oil's construction of an upgrader at their Scotsford plant. The North American pipeline system is the link between the upstream supply and the downstream demand. New pipeline projects have allowed increased supplies of Canadian heavy crude to gain access to new markets. It was emphasized that the downstream sector provides feedback to the upstream sector that influences producers when they plan their exploration, development and production activities. The picture in light crude production is the reverse of heavy crude oil production, i.e. Canadian light crude supply declined 4 per cent in 1996 from the average of the previous three years. This decline has given synthetic crude oil facilities like Syncrude and GCOS the chance to expand their production to offset a portion of the inland crude supply shortfall. 5 figs

Effect of zirconium addition on welding of aluminum grain refined by titanium

International Nuclear Information System (INIS)

Zaid, A.I.O.

2011-01-01

Aluminum and its alloys solidify in large grains columnar structure which tends to reduce their mechanical behaviour and surface quality. Therefore, they are industrially grain refined by titanium or titanium + boron. Furthermore, aluminum oxidizes in ordinary atmosphere which makes its weldability difficult and weak. Therefore, it is anticipated that the effect of addition of zirconium at a weight percentages of 0.1% (which proved to be an effective grain refiner on the weldability of aluminum grain refined by Ti) is worthwhile investigating. This formed the objective of this research work. In this paper, the effect of zirconium addition at a weight percentage of 0.1%, which corresponds to the peritctic limit on the aluminum-zirconium phase diagram, on the weldability of aluminum grain refined by Ti is investigated. Rolled sheets of commercially pure aluminum, Al grain refined Ti of 3 mm thickness were welded together using Gas Tungsten Arc Welding method (GTAW), formerly known as TIG. A constant air gap was maintained at a constant current level, 30 ampere AC, was used because it removes the oxides of the welding process under the same process parameters. Metallographic examination of weldments of the different combinations of aluminum and its microalloys at the heat affected zone, HAZ, and base metal was carried out and examined for width, porosity, cracks and microhardness. It was found that grain refining of commercially pure aluminum by Ti resulted in enhancement of its weldability. Similarly, addition of zirconium to Al grain refined by Ti resulted in further enhancement of the weldment. Photomicrographs of the HAZ regions are presented and discussed. (author)

Asian oil refining. Demand growth and deregulation - an uncertain future

International Nuclear Information System (INIS)

Sameer Nawaz.

1996-01-01

The objective of the report is to identify the most important features of the oil refining industry in Asia. Major developments in consumption patterns changes in regional importance of countries are discussed, highlighting potential future developments. The first chapter introduces the various refining processes and presents a simple model for the analysis of complex refineries. Chapter 2 examines the development of the Asian refining industry against a background of economic growth and analyses trends in consumption of all products in Asian countries. In Chapter 3, the key issues concerning the refining industry are examined, among them the forces driving consumption, including the importance of economic development, and electricity and transport demand. The importance of product imports and international trade is discussed, and the extent of government involvement and the effects of changing retail and market prices are analysed. Chapter 4 looks at the strategies that oil and gas companies are following in the Asian refining industry. Particular significance is attached to the vertical integration of the oil majors, Japanese and Middle Eastern oil companies. A brief overview of the importance of the petrochemical industry is presented. The countries of Asia that are involved in the refining industry are profiled in Chapter 5. The future trend in oil consumption is examined in Chapter 6. There follows a brief discussion of the plans to expand crude refining capacity in the various countries and a forecast of the state of overcapacity which will result. In the final chapter, brief profiles of some of the most important companies in the Asian refining industry are presented, discussing their major activities and future plans. (Author)

Refining an asynchronous telerehabilitation platform for speech-language pathology: Engaging end-users in the process

Directory of Open Access Journals (Sweden)

Annie Jane Hill

2016-12-01

feedback options to both the participant and clinician, automatic transfer of results to the clinician and expansion of the task template list. This research highlights the importance of including end-users in the process of technology refinement, in order to ensure effective and efficient use of the technology. Future directions for research are discussed including clinical trials in which the effectiveness of and adherence to intervention protocols using asynchronous telerehabilitation are examined.

The effect of refining step on the changes in viscosity values of vegetable oils

International Nuclear Information System (INIS)

Ergonul, P.G.

2013-01-01

In this work, the viscosity values of chemically refined vegetable oils (sunflower, corn, soybean and rapeseed) and physically refined vegetable oils (olive and palm) were determined during refining processes. At this point of view, fatty acid compositions and viscosity values of oil samples were determined. The edible vegetable oils presented Newtonian behavior in shear rates at ranges 6.28-20.93 s/sup -1/. It was observed that palm oil is more viscous than the others. During physical refining, the effect of both oil type and refining steps were significantly important, whereas in chemical refining only the effect of oil type was found statistically important (p<0.01). It was observed that correlation among fatty acid compositions and viscosity values of the samples showed differences according to oil type. (author)

Niobium-base grain refiner for aluminium

International Nuclear Information System (INIS)

Silva Pontes, P. da; Robert, M.H.; Cupini, N.L.

1980-01-01

A new chemical grain refiner for aluminium has been developed, using inoculation of a niobium-base compound. When a bath of molten aluminium is inoculated whith this refiner, an intermetallic aluminium-niobium compound is formed which acts as a powerful nucleant, producing extremely fine structure comparable to those obtained by means of the traditional grain refiner based on titanium and boron. It was found that the refinement of the structure depends upon the weight percentage of the new refiner inoculated as well as the time of holding the bath after inoculation and before pouring, but mainly on the inoculating temperature. (Author) [pt

Creativity: a refinement of the concept for nursing practice.

Science.gov (United States)

Fasnacht, Patsy H

2003-01-01

This paper seeks to remove some of the ambiguity surrounding the conceptual meaning of creativity using techniques of concept refinement to advance the concept. Creativity is an essential component of nursing practice that occurs daily in nurse's interactions with clients, families and other nurses. Failure to acknowledge and encourage creativity in beginning nurses may hinder future development and innovations in nursing practice and in nursing science. In order to promote the development of creativity it is first necessary to clarify and refine the concept as it applies to nursing. A comprehensive review of a variety of computer and online databases resulted in thousands of articles on creativity between the years 1966 and 1999. The final sample (n = 48) was obtained using both stratified random and purposive sampling techniques. A content analysis of the literature was conducted using methods identified by Morse and illustrated in the work of Hupcey et al. Having determined the concept to be partially mature, the concept was advanced using techniques of concept refinement. Content analysis of the literature yielded three differing definitions for creativity: revelation, birth and reincarnation. Creativity occurs in the presence of intrinsic motivation and a nurturing environment. While value is often used to identify whether a product is creative, the value of the product cannot determine whether the process has occurred. The product produced determines evidence of the process of creativity. Limitations of this investigation are the use of secondary sources and the relatively small sample size (n = 48). Refinement of the concept of creativity indicates that it is a process that may be developed and influenced by the environment and is recognized by the product produced. Further investigation is needed to explore methods and techniques for developing creativity in nursing.

Value added product recovery from sludge generated during gum arabic refining process by vermicomposting.

Science.gov (United States)

Das, Veena; Satyanarayan, Sanjeev; Satyanarayan, Shanta

2016-09-01

Gum arabic is multifunctional and used in food products, pharmaceutical, confectionery, cosmetic, printing and textile industry. Gum arabic has an excellent market and its production is being increased to meet the market demand. In the process, huge quantity of solid waste is generated during its refining process. An attempt has been made to vermicompost this organic waste using Eudrilus eugeniae. This research work is first of its kind. Literature on this substrate has not been reported anywhere else for vermicomposting. Results were excellent with volatile solid reduction of 51.34 %; C/N ratio reduced to 16.31 % indicating efficient loss of carbon as carbon dioxide during vermicomposting period. Manurial value, i.e. nitrogen, phosphorus and potassium content in the range, required for the plants also increased. Porosity of 67.74 % and water holding capacity of 65.75 % were observed. The maturity of the vermicompost was evaluated through scanning electron microscopy wherein the complete conversion of large raw material particles into finer particles forming a uniform matrix with more surface area was observed indicating its efficient conversion. Microbial quality of vermicompost was also studied. The final vermicompost is free of fungal cells and pathogenic bacteria.

Spanish Refining

International Nuclear Information System (INIS)

Lores, F.R.

2001-01-01

An overview of petroleum refining in Spain is presented (by Repsol YPF) and some views on future trends are discussed. Spain depends heavily on imports. Sub-headings in the article cover: sources of crude imports, investments and logistics and marketing, -detailed data for each are shown diagrammatically. Tables show: (1) economic indicators (e.g. total GDP, vehicle numbers and inflation) for 1998-200; (2) crude oil imports for 1995-2000; (3) oil products balance for 1995-2000; (4) commodities demand, by product; (5) refining in Spain in terms of capacity per region; (6) outlets in Spain and other European countries in 2002 and (7) sales distribution channel by product

Discontinuous Galerkin discretization and hp-refinement for the resolution of the neutron transport equation

International Nuclear Information System (INIS)

Fournier, Damien; Le-Tellier, Romain; Herbin, Raphaele

2013-01-01

This paper presents an hp-refinement method for a first order scalar transport reaction equation discretized by a discontinuous Galerkin method. First, the theoretical rates of convergence of h- and p-refinement are recalled and numerically tested. Then, in order to design some meshes, we propose two different estimators of the local error on the spatial domain. These quantities are analyzed and compared depending on the regularity of the solution so as to find the best way to lead the refinement process and the best strategy to choose between h- and p-refinement. Finally, the different possible refinement strategies are compared first on analytical examples and then on realistic applications for neutron transport in a nuclear reactor core. (authors)

Current research progress in grain refinement of cast magnesium alloys: A review article

International Nuclear Information System (INIS)

Ali, Yahia; Qiu, Dong; Jiang, Bin; Pan, Fusheng; Zhang, Ming-Xing

2015-01-01

Grain refinement of cast magnesium alloys, particularly in magnesium–aluminium (Mg–Al) based alloys, has been an active research topic in the past two decades, because it has been considered as one of the most effective approaches to simultaneously increase the strength, ductility and formability. The development of new grain refiners was normally based on the theories/models that were established through comprehensive and considerable studies of grain refinement in cast Al alloys. Generally, grain refinement in cast Al can be achieved through either inoculation treatment, which is a process of adding, or in situ forming, foreign particles to promote heterogeneous nucleation rate, or restricting grain growth by controlling the constitutional supercooling or both. But, the concrete and tangible grain refinement mechanism in cast metals is still not fully understood and there are a number of controversies. Therefore, most of the new developed grain refiners for Mg–Al based alloys are not as efficient as the commercially available ones, such as zirconium in non-Al containing Mg alloys. To facilitate the research in grain refinement of cast magnesium alloys, this review starts with highlighting the theoretical aspects of grain refinement in cast metals, followed by reviewing the latest research progress in grain refinement of magnesium alloys in terms of the solute effect and potent nucleants

Current research progress in grain refinement of cast magnesium alloys: A review article

Energy Technology Data Exchange (ETDEWEB)

Ali, Yahia; Qiu, Dong [School of Mechanical and Mining Engineering, University of Queensland, St Lucia, QLD 4072 (Australia); Jiang, Bin; Pan, Fusheng [College of Materials Science and Engineering, Chongqing University, Chongqing 400030 (China); Zhang, Ming-Xing, E-mail: Mingxing.Zhang@uq.edu.au [School of Mechanical and Mining Engineering, University of Queensland, St Lucia, QLD 4072 (Australia)

2015-01-15

Grain refinement of cast magnesium alloys, particularly in magnesium–aluminium (Mg–Al) based alloys, has been an active research topic in the past two decades, because it has been considered as one of the most effective approaches to simultaneously increase the strength, ductility and formability. The development of new grain refiners was normally based on the theories/models that were established through comprehensive and considerable studies of grain refinement in cast Al alloys. Generally, grain refinement in cast Al can be achieved through either inoculation treatment, which is a process of adding, or in situ forming, foreign particles to promote heterogeneous nucleation rate, or restricting grain growth by controlling the constitutional supercooling or both. But, the concrete and tangible grain refinement mechanism in cast metals is still not fully understood and there are a number of controversies. Therefore, most of the new developed grain refiners for Mg–Al based alloys are not as efficient as the commercially available ones, such as zirconium in non-Al containing Mg alloys. To facilitate the research in grain refinement of cast magnesium alloys, this review starts with highlighting the theoretical aspects of grain refinement in cast metals, followed by reviewing the latest research progress in grain refinement of magnesium alloys in terms of the solute effect and potent nucleants.

A case study: Residue reduction at Deer Park Refining Limited Partnership

International Nuclear Information System (INIS)

Geehan, D.M.

1996-01-01

With input from Shell Synthetic Fuels Inc. (SSFI), Deer Park Refining Limited Partnership (DPRLP) analyzed options for managing the bottom of the barrel to extinction, with an objective of high return on investment. DPRLP is a joint venture of PEMEX and Shell Oil Company. This Gulf Coast refiner processes 227M BBL/D of heavy, high sulfur crude. This paper discusses the process options considered, their advantages and disadvantages, and the option selected as well as the options still open. Recent modernization projects at DPRLP are now on stream with high yield of clean products.There remains one by-product, petroleum coke, which presents opportunity as a low cost feed for one or more process options yielding attractive products. The Shell Coke (or Coal) Gasification Process is one of the options now being considered

Flow Rate Measurement in Multiphase Flow Rig: Radiotracer and Conventional

International Nuclear Information System (INIS)

Nazrul Hizam Yusoff; Noraishah Othman; Nurliyana Abdullah; Amirul Syafiq Mohd Yunos; Rasif Mohd Zain; Roslan Yahya

2015-01-01

Applications of radiotracer technology are prevalent throughout oil refineries worldwide, and this industry is one of the main users and beneficiaries of the technology. Radioactive tracers have been used to a great extent in many applications i.e. flow rate measurement, RTD, plant integrity evaluation and enhancing oil production in oil fields. Chemical and petrochemical plants are generally continuously operating and technically complex where the radiotracer techniques are very competitive and largely applied for troubleshooting inspection and process analysis. Flow rate measurement is a typical application of radiotracers. For flow measurements, tracer data are important, rather than the RTD models. Research is going on in refining the existing methods for single phase flow measurement, and in developing new methods for multiphase flow without sampling. The tracer techniques for single phase flow measurements are recognized as ISO standards. This paper presents technical aspect of laboratory experiments, which have been carried out using Molybdenum-99 - Mo99 (radiotracer) to study and determine the flow rate of liquid in multiphase flow rig. The multiphase flow rig consists of 58.7 m long and 20 cm diameter pipeline that can accommodate about 0.296 m 3 of liquid. Tap water was used as liquid flow in pipeline and conventional flow meters were also installed at the flow rig. The flow rate results; radiotracer and conventional flow meter were compared. The total count method was applied for radiotracer technique and showed the comparable results with conventional flow meter. (author)

Biodiesel obtained from soapstock originated in a refining oil industry

International Nuclear Information System (INIS)

Tobio Pérez, Indira; Díaz Domínguez, Yosvany; Piloto-Rodríguez, Ramón

2017-01-01

In the vegetable oil chemical refining process is obtained a by-product commonly named as soapstock, due to its physical and aspect properties. The soapstock free fatty acid content can reach to 50%. The present work shows a survey of researches focused on biodiesel obtaining from this by-product. The biodiesel is obtained following different routes and catalyzers features. A variety of reports shown the effectivity of the use of this by-product derived from vegetable oil refining industry to produce biodiesel. Several studies are addressed to the acid oil recovering involving processes without soapstock acidulation, with the aim of lowering costs and finding more attractive yields closing to the concept of zero wastes. (author)

Neutron irradiation effects on grain-refined W and W-alloys

International Nuclear Information System (INIS)

Hasegawa, A.; Fukuda, M.; Tanno, T.; Nogami, S.; Yabuuchi, K.; Tanaka, T.; Muroga, T.

2014-10-01

Microstructural data of neutron irradiated Tungsten (W) such as size and number density of voids and precipitates obtained by W up to 1.5dpa irradiation in the temperature range of 400-800degC were compiled quantitatively. Nucleation and growth process of these defects were clarified and a qualitative prediction of the damage structure development and hardening of W in fusion reactor environments were made taking into account the solid transmutation effects for the first time. To improve recrystallization behavior and low temperature embrittlement, grain refined-W alloys were fabricated by K- or La-doping method. Rhenium addition to the grain refining process was also examined to improve mechanical properties. Characterizations of unirradiated materials were performed. (author)

Pacific Basin Heavy Oil Refining Capacity

Directory of Open Access Journals (Sweden)

David Hackett

2013-02-01

Full Text Available The United States today is Canada’s largest customer for oil and refined oil products. However, this relationship may be strained due to physical, economic and political influences. Pipeline capacity is approaching its limits; Canadian oil is selling at substantive discounts to world market prices; and U.S. demand for crude oil and finished products (such as gasoline, has begun to flatten significantly relative to historical rates. Lower demand, combined with increased shale oil production, means U.S. demand for Canadian oil is expected to continue to decline. Under these circumstances, gaining access to new markets such as those in the Asia-Pacific region is becoming more and more important for the Canadian economy. However, expanding pipeline capacity to the Pacific via the proposed Northern Gateway pipeline and the planned Trans Mountain pipeline expansion is only feasible when there is sufficient demand and processing capacity to support Canadian crude blends. Canadian heavy oil requires more refining and produces less valuable end products than other lighter and sweeter blends. Canadian producers must compete with lighter, sweeter oils from the Middle East, and elsewhere, for a place in the Pacific Basin refineries built to handle heavy crude blends. Canadian oil sands producers are currently expanding production capacity. Once complete, the Northern Gateway pipeline and the Trans Mountain expansion are expected to deliver an additional 500,000 to 1.1 million barrels a day to tankers on the Pacific coast. Through this survey of the capacity of Pacific Basin refineries, including existing and proposed facilities, we have concluded that there is sufficient technical capacity in the Pacific Basin to refine the additional Canadian volume; however, there may be some modifications required to certain refineries to allow them to process Western Canadian crude. Any additional capacity for Canadian oil would require refinery modifications or

Comparing Refinements for Failure and Bisimulation Semantics

NARCIS (Netherlands)

Eshuis, H.; Fokkinga, M.M.

2002-01-01

Refinement in bisimulation semantics is defined differently from refinement in failure semantics: in bisimulation semantics refinement is based on simulations between labelled transition systems, whereas in failure semantics refinement is based on inclusions between failure systems. There exist

Melt refining of uranium contaminated copper, nickel, and mild steel

International Nuclear Information System (INIS)

Ren Xinwen; Liu Wencang; Zhang Yuan

1993-01-01

This paper presents the experiment results on melt refining of uranium contaminated metallic discards such as copper, nickel, and mild steel. Based on recommended processes, uranium contents in ingots shall decrease below 1 ppm; metal recovery is higher than 96%; and slag production is below 5% in weight of the metal to be refined. The uranium in the slag is homogeneously distributed. The slag seems to be hard ceramics, insoluble in water, and can be directly disposed of after proper packaging

Reverse mechanical after effect during hydrogenation of zone refined iron

Energy Technology Data Exchange (ETDEWEB)

Spivak, L.V.; Skryabina, N.E.; Kurmaeva, L.D.; Smirnov, L.V. (Permskij Gosudarstvennyj Univ. (USSR); AN SSSR, Sverdlovsk. Inst. Fiziki Metallov)

1984-12-01

The relationship between the process of hydrogenation and the reverse mechanical after effect (RMA) microplastic deformation in the zone refined iron has been studied. Metallographic investigations and mechanical testing of the samples hydrogenated under torsional strain have been performed. It is shown that in the zone refined iron the formation of voids responsible for irreversible hydrogen embrittlement does not occur, but the hydrogen-initiated RMA strain is conserved, i. e. the RMA effects are independent of the presence of discontinuities.

Crystal structure refinement with SHELXL

Energy Technology Data Exchange (ETDEWEB)

Sheldrick, George M., E-mail: gsheldr@shelx.uni-ac.gwdg.de [Department of Structural Chemistry, Georg-August Universität Göttingen, Tammannstraße 4, Göttingen 37077 (Germany)

2015-01-01

New features added to the refinement program SHELXL since 2008 are described and explained. The improvements in the crystal structure refinement program SHELXL have been closely coupled with the development and increasing importance of the CIF (Crystallographic Information Framework) format for validating and archiving crystal structures. An important simplification is that now only one file in CIF format (for convenience, referred to simply as ‘a CIF’) containing embedded reflection data and SHELXL instructions is needed for a complete structure archive; the program SHREDCIF can be used to extract the .hkl and .ins files required for further refinement with SHELXL. Recent developments in SHELXL facilitate refinement against neutron diffraction data, the treatment of H atoms, the determination of absolute structure, the input of partial structure factors and the refinement of twinned and disordered structures. SHELXL is available free to academics for the Windows, Linux and Mac OS X operating systems, and is particularly suitable for multiple-core processors.

Production and characterization of refined oils obtained from Indian oil sardine (Sardinella longiceps).

Science.gov (United States)

Chakraborty, Kajal; Joseph, Deepu

2015-01-28

Crude Sardinella longiceps oil was refined in different stages such as degumming, neutralization, bleaching, and deodorization. The efficiency of these processes was evaluated on the basis of free fatty acid (FFA), peroxide (PV), p-anisidine (pAV), total oxidation (TOTOX), thiobarbituric acid reactive species (TBARS) values, Lovibond CIE-L*a*b* color analyses, and (1)H NMR or GC-MS experiments. The utilities of NMR-based proton signal characteristics as new analytical tools to understand the signature peaks and relative abundance of different fatty acids and monitoring the refining process of fish oil have been demonstrated. Phosphoric acid (1%) was found to be an effective degumming reagent to obtain oil with the lowest FFA, PV, pAV, TOTOX, and TBARS values and highest color reduction. Significant reduction in the contents of hydrocarbon functionalities as shown by the decrease in proton integral in the characteristic (1)H NMR region was demonstrated by using 1% H3PO4 during the course of the degumming process. A combination (1.25:3.75%) of activated charcoal and Fuller's earth at 3% concentration for a stirring time of 40 min was found to be effective in bleaching the sardine oil. This study demonstrated that unfavorable odor-causing components, particularly low molecular weight carbonyl compounds, could successfully be removed by the refining process. The alkane-dienals/alkanes, which cause unfavorable fishy odors, were successfully removed by distillation (100 °C) under vacuum with aqueous acetic acid solution (0.25 N) to obtain greater quality of refined sardine oil, a rich source of essential fatty acids and improved oxidative stability. The present study demonstrated that the four-stage refinement process of sardine oil resulted in a significant improvement in quality characteristics and nutritional values, particularly n-3 PUFAs, with improved fish oil characteristics for use in the pharmaceutical and functional food industries.

Numerical modelling of surface waves generated by low frequency electromagnetic field for silicon refinement process

Science.gov (United States)

Geža, V.; Venčels, J.; Zāģeris, Ģ.; Pavlovs, S.

2018-05-01

One of the most perspective methods to produce SoG-Si is refinement via metallurgical route. The most critical part of this route is refinement from boron and phosphorus, therefore, approach under development will address this problem. An approach of creating surface waves on silicon melt’s surface is proposed in order to enlarge its area and accelerate removal of boron via chemical reactions and evaporation of phosphorus. A two dimensional numerical model is created which include coupling of electromagnetic and fluid dynamic simulations with free surface dynamics. First results show behaviour similar to experimental results from literature.

Refining of fossil resin flotation concentrate from western coal. Final report

Energy Technology Data Exchange (ETDEWEB)

Jensen, G.F.; Miller, J.D.

1995-02-16

During the past several years, significant research efforts have been made to develop process technology for the selective flotation of fossil resin from western coals. As a result of these efforts, several new flotation technologies have been developed. Operation of a proof-of-concept continuous flotation circuit showed the selective flotation process to be sufficiently profitable to justify the development of a fossil resin industry. However, little attention has been given to the refining of the fossil resin flotation concentrate although solvent refining is a critical step for the fossil resin to become a marketable product. In view of this situation, DOE funded this two-year project to evaluate the following aspects of the fossil resin refining technology: 1) Characterization of the fossil resin flotation concentrate and its refined products; 2) Kinetics of fossil resin extraction; 3) Effects of operating variables on solvent extraction; 4) Extraction solvents; 5) Proof-of-concept continuous refining tests; and 6) Technical and economic analysis. The results from this research effort have led to the following conclusions: Hexane- or heptane-refined fossil resin has a light-yellow color, a melting point of 140 - 142{degrees}C, a density of 1.034 gram/cm, and good solubility in nonpolar solvents. Among the four solvents evaluated (hexane, heptane, toluene and ethyl acetate), hexane is the most appropriate solvent based on overall technical and economic considerations. Batch extraction tests and kinetic studies suggest that the main interaction between the resin and the solvent is expected to be the forces associated with solvation phenomena. Temperature has the most significant effect on extraction rate. With hexane as the solvent, a recovery of 90% cam be achieved at 50{degrees}C and 10% solids concentration with moderate agitation for 1 hour.

Profex: a graphical user interface for the Rietveld refinement program BGMN.

Science.gov (United States)

Doebelin, Nicola; Kleeberg, Reinhard

2015-10-01

Profex is a graphical user interface for the Rietveld refinement program BGMN . Its interface focuses on preserving BGMN 's powerful and flexible scripting features by giving direct access to BGMN input files. Very efficient workflows for single or batch refinements are achieved by managing refinement control files and structure files, by providing dialogues and shortcuts for many operations, by performing operations in the background, and by providing import filters for CIF and XML crystal structure files. Refinement results can be easily exported for further processing. State-of-the-art graphical export of diffraction patterns to pixel and vector graphics formats allows the creation of publication-quality graphs with minimum effort. Profex reads and converts a variety of proprietary raw data formats and is thus largely instrument independent. Profex and BGMN are available under an open-source license for Windows, Linux and OS X operating systems.

US refining capacity for Canadian heavy oil : current overview and future potential

International Nuclear Information System (INIS)

Paget, S.

2006-01-01

This presentation provided an overview of the Canadian oil sands industry and investigated the potential heavy oil refining capacity of the United States. An outline of the first commercial developments of steam assisted gravity drainage (SAGD) in Alberta's oil sands was provided. Canada's reserves were compared with oil shale and heavy oil reserves in the United States and Venezuela. Influences of Canadian developments from western Canadian conventional crude oil were reviewed, and an oil sands production forecast was provided. Recent refining developments in the United States include delayed coking; catalytic cracking; fluid coking; flexicoking; and LC-fining. However, many oil sand producers are now choosing to upgrade oil, and producers are currently saturating United States markets with heavy crude oil. Canadian crude prices reached $90 per barrel in 2006. Heavy oil pipelines are now being constructed and existing heavy oil pipelines are being expanded. ConocoPhillips is planning to invest $1 billion for a new heavy oil coker, while BP is investing $3 billion for a heavy oil refinery in Indiana which plans to refine Canadian crude oil supplies. However, bitumens from Alberta are volatile in price, and excess Canadian production must be exported. Less than 10 per cent of western Canadian crude has tidewater access, and capital providers are concerned about cost over-runs. In order for the Canadian oil sands industry to succeed, refining capacity in the United States must be expanded, and open access must be provided to the Gulf coast as well as to the Pacific Ocean. tabs., figs

A Refined Model for Calculation of the Vortex Tube Thermal Characteristics

Science.gov (United States)

Biryuk, V. V.; Gorshkalev, A. A.; Uglanov, D. A.; Urlapkin, V. V.; Korneev, S. S.

2018-01-01

The article deals with the main types of vortex tubes, provides a brief description of the fundamental principles of the vortex interaction hypothesis. A physical process is represented reflecting the physical essence of the gas flow energetic separation process in the vortex tube due to the intensive turbulent heat exchange from the forced vortex to the free one. A method for refinement of the design characteristics for the cold and hot gas temperatures in a vortex tube through the employment of the gas-dynamic and thermodynamic corrections is proposed. A refined calculation method allows reaching close agreement between the cold gas temperature and the experimental values.

Latin American oil markets and refining

International Nuclear Information System (INIS)

Yamaguchi, N.D.; Obadia, C.

1999-01-01

This paper provides an overview of the oil markets and refining in Argentina, Brazil, Chile, Colombia, Ecuador, Mexico, Peru and Venezuela, and examines the production of crude oil in these countries. Details are given of Latin American refiners highlighting trends in crude distillation unit capacity, cracking to distillation ratios, and refining in the different countries. Latin American oil trade is discussed, and charts are presented illustrating crude production, oil consumption, crude refining capacity, cracking to distillation ratios, and oil imports and exports

Comparison of Ti(C,N)-based cermets processed by hot-pressing sintering and conventional pressureless sintering

International Nuclear Information System (INIS)

Xu, Qingzhong; Ai, Xing; Zhao, Jun; Qin, Weizhen; Wang, Yintao; Gong, Feng

2015-01-01

Highlights: • The HP sintered Ti(C,N)-based cermets exhibit high hardness with fine grain size. • The PLS sintered cermets possess high mechanical properties with low porosity. • The applied pressure can rearrange particles and contribute to grain refinement. • The heating rate can greatly affect the solid and liquid phase sintering of cermets. - Abstract: A suitable sintering method is important to obtain the Ti(C,N)-based cermets with superior properties. In this paper, Ti(C,N)-based cermets were fabricated by hot-pressing sintering (HP) and conventional pressureless sintering (PLS) technology, respectively, to investigate the influence of different sintering methods on the microstructure and mechanical properties of cermets materials. The microstructure, fracture morphology, indention cracks and phase composition were observed and detected using scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The transverse rupture strength (TRS), Vickers hardness (HV) and fracture toughness (K IC ) were also measured. The results reveal that all of the Ti(C,N)-based cermets exhibit core–rim microstructures with black cores, white cores and grey rims embedded into metal binder phases. The grain size of the samples fabricated by HP is much finer and the structure is more compact than those fabricated by PLS, while there exist pores in the HP sintered samples. The sintering process has no influence on the phase composition of cermets, but affects the phase content and crystallinity. The samples fabricated by PLS present higher transverse rupture strength, fracture toughness and density than samples fabricated by HP. However, the HP sintered samples possess a higher hardness

Numerical solution of plasma fluid equations using locally refined grids

International Nuclear Information System (INIS)

Colella, P.

1997-01-01

This paper describes a numerical method for the solution of plasma fluid equations on block-structured, locally refined grids. The plasma under consideration is typical of those used for the processing of semiconductors. The governing equations consist of a drift-diffusion model of the electrons and an isothermal model of the ions coupled by Poisson's equation. A discretization of the equations is given for a uniform spatial grid, and a time-split integration scheme is developed. The algorithm is then extended to accommodate locally refined grids. This extension involves the advancement of the discrete system on a hierarchy of levels, each of which represents a degree of refinement, together with synchronization steps to ensure consistency across levels. A brief discussion of a software implementation is followed by a presentation of numerical results

Relational Demonic Fuzzy Refinement

Directory of Open Access Journals (Sweden)

Fairouz Tchier

2014-01-01

Full Text Available We use relational algebra to define a refinement fuzzy order called demonic fuzzy refinement and also the associated fuzzy operators which are fuzzy demonic join (⊔fuz, fuzzy demonic meet (⊓fuz, and fuzzy demonic composition (□fuz. Our definitions and properties are illustrated by some examples using mathematica software (fuzzy logic.

Panorama 2012 - Refining 2030

International Nuclear Information System (INIS)

Marion, Pierre; Saint-Antonin, Valerie

2011-11-01

The major uncertainty characterizing the global energy landscape impacts particularly on transport, which remains the virtually-exclusive bastion of the oil industry. The industry must therefore respond to increasing demand for mobility against a background marked by the emergence of alternatives to oil-based fuels and the need to reduce emissions of pollutants and greenhouse gases (GHG). It is in this context that the 'Refining 2030' study conducted by IFP Energies Nouvelles (IFPEN) forecasts what the global supply and demand balance for oil products could be, and highlights the type and geographical location of the refinery investment required. Our study shows that the bulk of the refining investment will be concentrated in the emerging countries (mainly those in Asia), whilst the areas historically strong in refining (Europe and North America) face reductions in capacity. In this context, the drastic reduction in the sulphur specification of bunker oil emerges as a structural issue for European refining, in the same way as increasingly restrictive regulation of refinery CO 2 emissions (quotas/taxation) and the persistent imbalance between gasoline and diesel fuels. (authors)

Materials refining on the Moon

Science.gov (United States)

Landis, Geoffrey A.

2007-05-01

Oxygen, metals, silicon, and glass are raw materials that will be required for long-term habitation and production of structural materials and solar arrays on the Moon. A process sequence is proposed for refining these materials from lunar regolith, consisting of separating the required materials from lunar rock with fluorine. The fluorine is brought to the Moon in the form of potassium fluoride, and is liberated from the salt by electrolysis in a eutectic salt melt. Tetrafluorosilane produced by this process is reduced to silicon by a plasma reduction stage; the fluorine salts are reduced to metals by reaction with metallic potassium. Fluorine is recovered from residual MgF and CaF2 by reaction with K2O.

Refining margins and prospects

International Nuclear Information System (INIS)

Baudouin, C.; Favennec, J.P.

1997-01-01

Refining margins throughout the world have remained low in 1996. In Europe, in spite of an improvement, particularly during the last few weeks, they are still not high enough to finance new investments. Although the demand for petroleum products is increasing, experts are still sceptical about any rapid recovery due to prevailing overcapacity and to continuing capacity growth. After a historical review of margins and an analysis of margins by regions, we analyse refining over-capacities in Europe and the unbalances between production and demand. Then we discuss the current situation concerning barriers to the rationalization, agreements between oil companies, and the consequences on the future of refining capacities and margins. (author)

Preparation of Al-Ti-B grain refiner by SHS technology

International Nuclear Information System (INIS)

Nikitin, V.I.; Wanqi, J.I.E.; Kandalova, E.G.; Makarenko, A.G.; Yong, L.

2000-01-01

Since the discovery of the grain refinement effect of aluminum by titanium, especially with the existence of B or C in 1950, grain refiners are widely accepted in industry for microstructure control of aluminum alloys. Research on this topic is to obtain the highest grain refinement efficiency with the lowest possible addition of master alloy. It is widely accepted that the morphology and size of TiAl 3 particles, which are known as heterogeneous nucleation centers, are important factors deterring the grain refinement efficiency. Fine TiAl 3 particles are favorable. The grain refinement process shows a heredity phenomenon, which means that structural information from initial materials transfers through a melt to the final product. It is important to find the connection between microstructural parameters of the master alloy and the final product. To improve the quality of Al-Ti-B master alloys for the use as a grain refiner, a new method based on SHS (self-propagating high-temperature synthesis) technology has been developed in Samara State Technical University to produce the master alloys. SHS, as a new method for preparation of materials, was first utilized by Merzhanov in 1967. This method uses the energy from highly exothermic reactions to sustain the chemical reaction in a combustion wave. The advantages of SHS include simplicity, low energy requirement, and higher product purity. Because SHS reactions can take place between elemental reactants, it is easy to control product composition. The purposes of this investigation were to fabricate an SHS Al-5%Ti-1%B master alloy, to analyze its structure and to test its grain refining performance

Rising costs call for new European refining strategies

International Nuclear Information System (INIS)

Sweeney, B.N.C.

1993-01-01

The outlook for the global refining industry is for increased spending and reduced margins, largely because of efforts to improve the environment. A look at these trends through the end of the decade is thus in order. Three major industry thrusts are proposed to see refiners through this uncertain period. Three main thrusts are necessary: fixed costs must be reduced by re-engineering business processes and reexamining noncore business units against total and marginal costs. In this respect the best refiners are well ahead of the good ones. New cooperative ways of meeting regulations must be sought, to avoid wasteful over capacity. Joint ventures and alliances with competitors will be needed. The cooperative principle upstream must be extended and new strategies must be sought to meet product demand changes and reduce feedstock costs. The picture that is presented is tough, largely because of the wish to improve the environment. The question that must be continually reviewed is ''Have governments got the right balance in these regulations between the environment and the downstream industry?''

Re-examination of Chinese semantic processing and syntactic processing: evidence from conventional ERPs and reconstructed ERPs by residue iteration decomposition (RIDE.

Directory of Open Access Journals (Sweden)

Fang Wang

Full Text Available A number of studies have explored the time course of Chinese semantic and syntactic processing. However, whether syntactic processing occurs earlier than semantics during Chinese sentence reading is still under debate. To further explore this issue, an event-related potentials (ERPs experiment was conducted on 21 native Chinese speakers who read individually-presented Chinese simple sentences (NP1+VP+NP2 word-by-word for comprehension and made semantic plausibility judgments. The transitivity of the verbs was manipulated to form three types of stimuli: congruent sentences (CON, sentences with a semantically violated NP2 following a transitive verb (semantic violation, SEM, and sentences with a semantically violated NP2 following an intransitive verb (combined semantic and syntactic violation, SEM+SYN. The ERPs evoked from the target NP2 were analyzed by using the Residue Iteration Decomposition (RIDE method to reconstruct the ERP waveform blurred by trial-to-trial variability, as well as by using the conventional ERP method based on stimulus-locked averaging. The conventional ERP analysis showed that, compared with the critical words in CON, those in SEM and SEM+SYN elicited an N400-P600 biphasic pattern. The N400 effects in both violation conditions were of similar size and distribution, but the P600 in SEM+SYN was bigger than that in SEM. Compared with the conventional ERP analysis, RIDE analysis revealed a larger N400 effect and an earlier P600 effect (in the time window of 500-800 ms instead of 570-810ms. Overall, the combination of conventional ERP analysis and the RIDE method for compensating for trial-to-trial variability confirmed the non-significant difference between SEM and SEM+SYN in the earlier N400 time window. Converging with previous findings on other Chinese structures, the current study provides further precise evidence that syntactic processing in Chinese does not occur earlier than semantic processing.

Comparison of Environment Impact between Conventional and Cold Chain Management System in Paprika Distribution Process

Directory of Open Access Journals (Sweden)

Eidelweijs A Putri

2012-09-01

Full Text Available Pasir Langu village in Cisarua, West Java, is the largest central production area of paprika in Indonesia. On average, for every 200 kilograms of paprika produced, there is rejection amounting to 3 kilograms. This resulted in money loss for wholesalers and wastes. In one year, this amount can be approximately 11.7 million Indonesian rupiahs. Recently, paprika wholesalers in Pasir Langu village recently are developing cold chain management system to maintain quality of paprika so that number of rejection can be reduced. The objective of this study is to compare environmental impacts between conventional and cold chain management system in paprika distribution process using Life Cycle Assessment (LCA methodology and propose Photovoltaic (PV system in paprika distribution process. The result implies that the cold chain system produces more CO2 emission compared to conventional system. However, due to the promotion of PV system, the emission would be reduced. For future research, it is necessary to reduce CO2 emission from transportation process since this process is biggest contributor of CO2 emission at whole distribution process. Keywords: LCA, environmentally friendly distribution, paprika,cold chain, PV system

Refinement Types for TypeScript

OpenAIRE

Vekris, Panagiotis; Cosman, Benjamin; Jhala, Ranjit

2016-01-01

We present Refined TypeScript (RSC), a lightweight refinement type system for TypeScript, that enables static verification of higher-order, imperative programs. We develop a formal core of RSC that delineates the interaction between refinement types and mutability. Next, we extend the core to account for the imperative and dynamic features of TypeScript. Finally, we evaluate RSC on a set of real world benchmarks, including parts of the Octane benchmarks, D3, Transducers, and the TypeScript co...

Nucleation mechanisms of refined alpha microstructure in beta titanium alloys

Science.gov (United States)

Zheng, Yufeng

Due to a great combination of physical and mechanical properties, beta titanium alloys have become promising candidates in the field of chemical industry, aerospace and biomedical materials. The microstructure of beta titanium alloys is the governing factor that determines their properties and performances, especially the size scale, distribution and volume fraction of precipitate phase in parent phase matrix. Therefore in order to enhance the performance of beta titanium alloys, it is critical to obtain a thorough understanding of microstructural evolution in beta titanium alloys upon various thermal and/or mechanical processes. The present work is focusing on the study of nucleation mechanisms of refined alpha microstructure and super-refined alpha microstructure in beta titanium alloys in order to study the influence of instabilities within parent phase matrix on precipitates nucleation, including compositional instabilities and/or structural instabilities. The current study is primarily conducted in Ti-5Al-5Mo-5V-3Cr (wt%, Ti-5553), a commercial material for aerospace application. Refined and super-refined precipitates microstructure in Ti-5553 are obtained under specific accurate temperature controlled heat treatments. The characteristics of either microstructure are investigated in details using various characterization techniques, such as SEM, TEM, STEM, HRSTEM and 3D atom probe to describe the features of microstructure in the aspect of morphology, distribution, structure and composition. Nucleation mechanisms of refined and super-refined precipitates are proposed in order to fully explain the features of different precipitates microstructure in Ti-5553. The necessary thermodynamic conditions and detailed process of phase transformations are introduced. In order to verify the reliability of proposed nucleation mechanisms, thermodynamic calculation and phase field modeling simulation are accomplished using the database of simple binary Ti-Mo system

The limit of grain refinement on equal channel angular deformation

International Nuclear Information System (INIS)

Kopylov, V.I.; Chuvil'deev, V.N.

2004-01-01

Experimental and theoretical study results on the process of strain-induced grain refinement under severe plastic deformation are described. A generalization is made for experimental results on deformation dispersing of copper, magnesium and aluminium base alloys as well as unalloyed metals. The model is developed which allows calculating the minimal grain size being able to result from equal channel angular pressing. The expressions describing the dependence of the limit of grain refinement on the nature of the material and severe plastic deformation rate and temperature are obtained [ru

Using high-order methods on adaptively refined block-structured meshes - discretizations, interpolations, and filters.

Energy Technology Data Exchange (ETDEWEB)

Ray, Jaideep; Lefantzi, Sophia; Najm, Habib N.; Kennedy, Christopher A.

2006-01-01

Block-structured adaptively refined meshes (SAMR) strive for efficient resolution of partial differential equations (PDEs) solved on large computational domains by clustering mesh points only where required by large gradients. Previous work has indicated that fourth-order convergence can be achieved on such meshes by using a suitable combination of high-order discretizations, interpolations, and filters and can deliver significant computational savings over conventional second-order methods at engineering error tolerances. In this paper, we explore the interactions between the errors introduced by discretizations, interpolations and filters. We develop general expressions for high-order discretizations, interpolations, and filters, in multiple dimensions, using a Fourier approach, facilitating the high-order SAMR implementation. We derive a formulation for the necessary interpolation order for given discretization and derivative orders. We also illustrate this order relationship empirically using one and two-dimensional model problems on refined meshes. We study the observed increase in accuracy with increasing interpolation order. We also examine the empirically observed order of convergence, as the effective resolution of the mesh is increased by successively adding levels of refinement, with different orders of discretization, interpolation, or filtering.

China's refiners face massive overhaul, expansion to meet demand growth, new crude slate

International Nuclear Information System (INIS)

Anon.

1994-01-01

China's refining industry has embarked on a massive overhaul and expansion to accommodate soaring domestic growth in refined products demand. Currently that growth in demand is being met by increasing imports of refined products, in recent years attaining triple digit growth rates and squeezing direly needed foreign exchange. The focus is on adding refining capacity of about 1.4 million b/d to the current capacity of about 3.2 million b/d by 2000. Priority for increasing capacity is being given to expanding existing refineries and participating in foreign joint venture grassroots refineries along China's booming coastal regions as well as hiking output. A major challenge for China's refineries is that country's reentry into the General Agreement on Tariffs and Trade (GATT), recently signed in Morocco by more than 100 nations. The accompanying reduction of tariffs on imported refined products will make it more difficult for China's marginal refineries to compete in the domestic market. The paper discusses imports and exports, LPG outlook, refining capacity, revamps needed, third party processing, China's first joint venture refinery, industry plans, and GATT challenges

Summary of uranium refining and conversion pilot plant at Ningyo-toge works

International Nuclear Information System (INIS)

Iwata, Ichiro

1981-01-01

In the Ningyo-toge works, Power Reactor and Nuclear Fuel Development Corp., the construction of the uranium refining and conversion pilot plant was completed, and the operation will be started after the various tests based on the related laws. As for the uranium refining in Japan, the PNC process by wet refining method has been developed since 1958. The history of the development is described. It was decided to construct the refining and conversion pilot plant with 200 t uranium/year capacity as the comprehensive result of the development. This is the amount sufficient to supply UF 6 to the uranium enrichment pilot plant in Ningyo-toge. The building for the refining and conversion pilot plant is a three-story ferro-concrete building with the total floor area of about 13,000 m 2 . The raw materials are the uranium ore produced in Ningyo-toge and the yellow cakes from abroad. Uranyl sulfate solution is obtained by solvent extraction using an extraction tower or a mixer-settler. The following processes are electrolytic reduction, precipitation of uranium tetrafluoride, filtration, drying, dehydration and UF 6 conversion. The fluorine for UF 6 conversion is produced by the facility in the plant. The operation of the pilot plant will be started in the latter half of the fiscal year 1981, the batch operation is carrried out in 1982, and the continuous operation from 1983. (Kako, I.)

Glycidyl fatty acid esters in refined edible oils: A review on formation, occurrence, analysis, and elimination methods

Science.gov (United States)

Glycidyl fatty acid esters (GEs), one of the main contaminants in processed oil, are mainly formed during the deodorization step in the oil refining process of edible oils and therefore occur in almost all refined edible oils. GEs are potential carcinogens, due to the fact that they hydrolyze into t...

Linkages between the markets for crude oil and the markets for refined products

International Nuclear Information System (INIS)

Didziulis, V.S.

1990-01-01

To understand the crude oil price determination process it is necessary to extend the analysis beyond the markets for petroleum. Crude oil prices are determined in two closely related markets: the markets for crude oil and the markets for refined products. An econometric-linear programming model was developed to capture the linkages between the markets for crude oil and refined products. In the LP refiners maximize profits given crude oil supplies, refining capacities, and prices of refined products. The objective function is profit maximization net of crude oil prices. The shadow price on crude oil gives the netback price. Refined product prices are obtained from the econometric models. The model covers the free world divided in five regions. The model is used to analyze the impacts on the markets of policies that affect crude oil supplies, the demands for refined products, and the refining industry. For each scenario analyzed the demand for crude oil is derived from the equilibrium conditions in the markets for products. The demand curve is confronted with a supply curve which maximizes revenues providing an equilibrium solution for both crude oil and product markets. The model also captures crude oil price differentials by quality. The results show that the demands for crude oil are different across regions due to the structure of the refining industries and the characteristics of the demands for refined products. Changes in the demands for products have a larger impact on the markets than changes in the refining industry. Since markets for refined products and crude oil are interrelated they can't be analyzed individually if an accurate and complete assessment of a policy is to be made. Changes in only one product market in one region affect the other product markets and the prices of crude oil

Interspinous process device versus standard conventional surgical decompression for lumbar spinal stenosis: Randomized controlled trial

NARCIS (Netherlands)

W.A. Moojen (Wouter); M.P. Arts (Mark); W.C.H. Jacobs (Wilco); E.W. van Zwet (Erik); M.E. van den Akker-van Marle (Elske); B.W. Koes (Bart); C.L.A.M. Vleggeert-Lankamp (Carmen); W.C. Peul (Wilco)

2013-01-01

markdownabstractAbstract Objective To assess whether interspinous process device implantation is more effective in the short term than conventional surgical decompression for patients with intermittent neurogenic claudication due to lumbar spinal stenosis. Design Randomized controlled

Automating crystallographic structure solution and refinement of protein–ligand complexes

International Nuclear Information System (INIS)

Echols, Nathaniel; Moriarty, Nigel W.; Klei, Herbert E.; Afonine, Pavel V.; Bunkóczi, Gábor; Headd, Jeffrey J.; McCoy, Airlie J.; Oeffner, Robert D.; Read, Randy J.; Terwilliger, Thomas C.; Adams, Paul D.

2013-01-01

A software system for automated protein–ligand crystallography has been implemented in the Phenix suite. This significantly reduces the manual effort required in high-throughput crystallographic studies. High-throughput drug-discovery and mechanistic studies often require the determination of multiple related crystal structures that only differ in the bound ligands, point mutations in the protein sequence and minor conformational changes. If performed manually, solution and refinement requires extensive repetition of the same tasks for each structure. To accelerate this process and minimize manual effort, a pipeline encompassing all stages of ligand building and refinement, starting from integrated and scaled diffraction intensities, has been implemented in Phenix. The resulting system is able to successfully solve and refine large collections of structures in parallel without extensive user intervention prior to the final stages of model completion and validation

Neutron Powder Diffraction and Constrained Refinement

DEFF Research Database (Denmark)

Pawley, G. S.; Mackenzie, Gordon A.; Dietrich, O. W.

1977-01-01

The first use of a new program, EDINP, is reported. This program allows the constrained refinement of molecules in a crystal structure with neutron diffraction powder data. The structures of p-C6F4Br2 and p-C6F4I2 are determined by packing considerations and then refined with EDINP. Refinement is...

Hardness and microstructure homogeneity of pure copper processed by accumulative back extrusion

International Nuclear Information System (INIS)

Bazaz, B.; Zarei-Hanzaki, A.; Fatemi-Varzaneh, S.M.

2013-01-01

The present work deals with the microstructure evolution of a pure copper processed by a new severe plastic deformation method. A set of pure copper (99.99%) work-pieces with coarse-grained microstructures was processed by accumulative back extrusion (ABE) method at room temperature. The optical and scanning electron microscopy (SEM) and hardness measurements were utilized to study the microstructural evolution and hardness homogeneity. The results indicated that ABE is a capable process to provide a homogenous grain refined microstructure in pure copper. The observed grain refinement was discussed relying on the occurrence of dynamic restoration processes. The analysis of microstructure and hardness showed outstanding homogeneity improvement throughout the work-pieces as the consecutive ABE passes were applied. The homogeneity improvement was attributed to the propagation of the shear bands and also the heavily deformed regions. A reversing route was also applied in the ABE processing to investigate its effect on the development of microstructural homogeneity. Comparing to the conventional route, the application of the reversing route was found to yield better homogeneity after less passes of the process.

Refined geometric transition and qq-characters

Science.gov (United States)

Kimura, Taro; Mori, Hironori; Sugimoto, Yuji

2018-01-01

We show the refinement of the prescription for the geometric transition in the refined topological string theory and, as its application, discuss a possibility to describe qq-characters from the string theory point of view. Though the suggested way to operate the refined geometric transition has passed through several checks, it is additionally found in this paper that the presence of the preferred direction brings a nontrivial effect. We provide the modified formula involving this point. We then apply our prescription of the refined geometric transition to proposing the stringy description of doubly quantized Seiberg-Witten curves called qq-characters in certain cases.

Trends in heavy oil production and refining in California

International Nuclear Information System (INIS)

Olsen, D.K.; Ramzel, E.B.; Pendergrass, R.A. II.

1992-07-01

This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production and is part of a study being conducted for the US Department of Energy. This report summarizes trends in oil production and refining in Canada. Heavy oil (10 degrees to 20 degrees API gravity) production in California has increased from 20% of the state's total oil production in the early 1940s to 70% in the late 1980s. In each of the three principal petroleum producing districts (Los Angeles Basin, Coastal Basin, and San Joaquin Valley) oil production has peaked then declined at different times throughout the past 30 years. Thermal production of heavy oil has contributed to making California the largest producer of oil by enhanced oil recovery processes in spite of low oil prices for heavy oil and stringent environmental regulation. Opening of Naval Petroleum Reserve No. 1, Elk Hills (CA) field in 1976, brought about a major new source of light oil at a time when light oil production had greatly declined. Although California is a major petroleum-consuming state, in 1989 the state used 13.3 billion gallons of gasoline or 11.5% of US demand but it contributed substantially to the Nation's energy production and refining capability. California is the recipient and refines most of Alaska's 1.7 million barrel per day oil production. With California production, Alaskan oil, and imports brought into California for refining, California has an excess of oil and refined products and is a net exporter to other states. The local surplus of oil inhibits exploitation of California heavy oil resources even though the heavy oil resources exist. Transportation, refining, and competition in the market limit full development of California heavy oil resources

Recovery of condensates from the thermal wood refinement extraction of biomolecules

Energy Technology Data Exchange (ETDEWEB)

Roschitz, C.; Martini, S.; Kleinhappl, M. (Austrian Bioenergy Centre GmbH, Area Gasification, Graz (Austria)); Jenny, M.; Wrulicit, O.A.; Wondrak, A.; Ueberall, E. (Innsbruck University of Medicine, Biocenter, Division of Medical Biochemistry, Innsbruck (Austria)); Fillafer, F.; Steiner, F. (Mafi Holzverarbeitung GmbH, Schneegattern (Austria)); Draxler, J. (Leoben University of Mining and Materials, Institute for Process technology and Industrial Environment Protection, Leoben (Austria))

2007-07-01

Generally the utilisation of woody biomass is dominated by the pulp and paper industry, its use for energy production by combustion or gasification and as a construction material. A large potential of substances could be gained directly and indirectly from biomass. During industrial processes like the thermal wood refinement or the digestion from wood to pulp a large spectrum of substances could be recovered. This paper gives an idea of how to obtain and use those special substances contained in woody biomass. Therefore this project was launched to investigate exhaust vapours originating from industrial wood refining processes. The exhaust vapour of a thermal wood refinement chamber, which works at 150 - 220 deg C, was sampled and its constituents of low amount were investigated. Substance classes like organic acids, aldehydes, esters alcohols, lignin fractions and resin like compounds were identified. The bioactivity of the samples was investigated in biological test procedures, to identify the characteristic pattern of impression (toxicity, antioxidants, gene expression). The technological step of recovery in small ale during the refinery process is under construction and will perform the staged recovery of valuable fractions. The pilot scale plant will give the chance to gain test fractions in sufficient amount to generate materials for application as chemicals, additives for detergents and cleaning agents. (orig.)

Solvent refined coal (SRC) process. Quarterly technical progress report, January 1980-March 1980. [In process streams

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

This report summarizes the progress of the Solvent Refined Coal (SRC) project at the SRC Pilot Plant in Fort Lewis, Wahsington, and the Process Development Unit (P-99) in Harmarville, Pennsylvania. After the remaining runs of the slurry preheater survey test program were completed January 14, the Fort Lewis Pilot Plant was shut down to inspect Slurry Preheater B and to insulate the coil for future testing at higher rates of heat flux. Radiographic inspection of the coil showed that the welds at the pressure taps and the immersion thermowells did not meet design specifications. Slurry Preheater A was used during the first 12 days of February while weld repairs and modifications to Slurry Preheater B were completed. Two attempts to complete a material balance run on Powhatan No. 6 Mine coal were attempted but neither was successful. Slurry Preheater B was in service the remainder of the quarter. The start of a series of runs at higher heat flux was delayed because of plugging in both the slurry and the hydrogen flow metering systems. Three baseline runs and three slurry runs of the high heat flux program were completed before the plant was shut down March 12 for repair of the Inert Gas Unit. Attempts to complete a fourth slurry run at high heat flux were unsuccessful because of problems with the coal feed handling and the vortex mix systems. Process Development Unit (P-99) completed three of the four runs designed to study the effect of dissolver L/D ratio. The fourth was under way at the end of the period. SRC yield correlations have been developed that include coal properties as independent variables. A preliminary ranking of coals according to their reactivity in PDU P-99 has been made. Techniques for studying coking phenomenona are now in place.

Refinement of the gross theory of nuclear {beta}-decay, and hindrance of the first-forbidden transition of rank 1

Energy Technology Data Exchange (ETDEWEB)

Nakata, Hidehiko [Waseda Univ., Tokyo (Japan). Dept. of Physics; Tachibana, Takahiro; Yamada, Masami

1997-03-01

Recently the gross theory of nuclear {beta}-decay was refined for odd-odd nuclei. In this refinement, the effect of the selection rule of {beta}-transitions from the ground states of odd-odd nuclei to those of even-even nuclei was taken into account based on a statistical consideration. The transitions to the first 2{sup +} excited states in even-even nuclei were also taken into account according to the selection rule approximately. In that study, it was found that the transitions between 1{sup -} ground states of the odd-odd nuclei and 0{sup +} ground states of even-even nuclei, belonging to the first-forbidden transitions of rank 1, are strongly hindered. A reduction factor was introduced for the transitions to the ground states of even-even nuclei to take into account this hindrance. It was also found that the strength functions of the Gamow-Teller transitions obtained from the conventional gross theory are underestimated by a factor of about 3. In order to improve this underestimation, the Lorentz-type function was adopted for the one-particle strength function in the model instead of the hyperbolic-secant-type function. In the present study we have newly analyzed the experimental ft-values of odd-A nuclei, and found that the first-forbidden transitions of rank 1 are also considerably hindered between the ground states. Following the above refinement we have calculated the {beta}-ray spectra of some odd-odd short-lived fission products with the use of the refined gross theory. These results are compared not only with the experiments by Rudstam et al. but also with the conventional gross theory. (author)

Evaluation of unrestrained replica-exchange simulations using dynamic walkers in temperature space for protein structure refinement.

Directory of Open Access Journals (Sweden)

Mark A Olson

Full Text Available A central problem of computational structural biology is the refinement of modeled protein structures taken from either comparative modeling or knowledge-based methods. Simulations are commonly used to achieve higher resolution of the structures at the all-atom level, yet methodologies that consistently yield accurate results remain elusive. In this work, we provide an assessment of an adaptive temperature-based replica exchange simulation method where the temperature clients dynamically walk in temperature space to enrich their population and exchanges near steep energetic barriers. This approach is compared to earlier work of applying the conventional method of static temperature clients to refine a dataset of conformational decoys. Our results show that, while an adaptive method has many theoretical advantages over a static distribution of client temperatures, only limited improvement was gained from this strategy in excursions of the downhill refinement regime leading to an increase in the fraction of native contacts. To illustrate the sampling differences between the two simulation methods, energy landscapes are presented along with their temperature client profiles.

On Modal Refinement and Consistency

DEFF Research Database (Denmark)

Nyman, Ulrik; Larsen, Kim Guldstrand; Wasowski, Andrzej

2007-01-01

Almost 20 years after the original conception, we revisit several fundamental question about modal transition systems. First, we demonstrate the incompleteness of the standard modal refinement using a counterexample due to Hüttel. Deciding any refinement, complete with respect to the standard...

Impact of processing on in vitro digestion of milk from grazing organic and confined conventional herds

Science.gov (United States)

Debate on differences between milk from grazing and non-grazing cows has not addressed the effects that standard processing may have on milk digestibility. In this study, raw milk from grazing organic (ORG) and non-grazing conventional (CONV) herds was adjusted to 0 and 3.25% fat and processed as fo...

Automatic mesh refinement and local multigrid methods for contact problems: application to the Pellet-Cladding mechanical Interaction

International Nuclear Information System (INIS)

Liu, Hao

2016-01-01

This Ph.D. work takes place within the framework of studies on Pellet-Cladding mechanical Interaction (PCI) which occurs in the fuel rods of pressurized water reactor. This manuscript focuses on automatic mesh refinement to simulate more accurately this phenomena while maintaining acceptable computational time and memory space for industrial calculations. An automatic mesh refinement strategy based on the combination of the Local Defect Correction multigrid method (LDC) with the Zienkiewicz and Zhu a posteriori error estimator is proposed. The estimated error is used to detect the zones to be refined, where the local sub-grids of the LDC method are generated. Several stopping criteria are studied to end the refinement process when the solution is accurate enough or when the refinement does not improve the global solution accuracy anymore. Numerical results for elastic 2D test cases with pressure discontinuity show the efficiency of the proposed strategy. The automatic mesh refinement in case of unilateral contact problems is then considered. The strategy previously introduced can be easily adapted to the multi-body refinement by estimating solution error on each body separately. Post-processing is often necessary to ensure the conformity of the refined areas regarding the contact boundaries. A variety of numerical experiments with elastic contact (with or without friction, with or without an initial gap) confirms the efficiency and adaptability of the proposed strategy. (author) [fr

Refining - Panorama 2008

International Nuclear Information System (INIS)

2008-01-01

Investment rallied in 2007, and many distillation and conversion projects likely to reach the industrial stage were announced. With economic growth sustained in 2006 and still pronounced in 2007, oil demand remained strong - especially in emerging countries - and refining margins stayed high. Despite these favorable business conditions, tensions persisted in the refining sector, which has fallen far behind in terms of investing in refinery capacity. It will take renewed efforts over a long period to catch up. Looking at recent events that have affected the economy in many countries (e.g. the sub-prime crisis), prudence remains advisable

The Generation of AlmFe in Dilute Aluminium Alloys with Different Grain Refining Additions

Science.gov (United States)

Meredith, M. W.; Greer, A. L.; Evans, P. V.; Hamerton, R. G.

Al13Fe4, Al6Fe and AlmFe are common intermetallics in commercial AA1XXX series Al alloys. Grain-refining additions (based on either Al-Ti-B or Al-Ti-C) are usually added to such alloys during solidification processing to aid the grain structure development. They also influence the favoured intermetallic and, hence, can affect the materials' properties. This work simulates commercial casting practices in an attempt to determine the mechanisms by which one intermetallic phase is favoured over another by the introduction of grain-refining additions. Directional solidification experiments on Al-0.3wt.%Fe-0.15wt.%Si with and without grain refiner are conducted using Bridgman apparatus. The type, amount and effectiveness of the grain-refining additions are altered and the resulting intermetallic phase selection followed. The materials are characterised using optical microscopy, scanning electron microscopy and X-ray diffraction. AlmFe is seen to form when Al-Ti-B grain-refiner is introduced but only when the refinement is successful; reducing the effectiveness of the refiner led to Al6Fe forming under all conditions. Al-Ti-C refiners are seen to promote AlmFe at lower solidification velocities than when Al-Ti-B was used even though the grain structure was not as refined. These trends can be explained within existing eutectic theory, by considering growth undercooling.

The Aarhus Convention: A new regional convention on citizens' environmental rights

International Nuclear Information System (INIS)

Wates, J.

2000-01-01

The UN ECE Convention on Access to Information, Public Participation in Decision-making and Access to Justice in Environmental Matters had been adopted at Arhus, Denmark, at the Fourth Ministerial Conference in the 'Environment for Europe' process, and signed by thirty-five countries and the European Community. This paper summarises the main features of the Convention and briefly discusses its relevance to radioactive waste management issues. It then describes some of the activities currently being undertaken under the auspices of the Convention. (author)

i3Drefine software for protein 3D structure refinement and its assessment in CASP10.

Science.gov (United States)

Bhattacharya, Debswapna; Cheng, Jianlin

2013-01-01

Protein structure refinement refers to the process of improving the qualities of protein structures during structure modeling processes to bring them closer to their native states. Structure refinement has been drawing increasing attention in the community-wide Critical Assessment of techniques for Protein Structure prediction (CASP) experiments since its addition in 8(th) CASP experiment. During the 9(th) and recently concluded 10(th) CASP experiments, a consistent growth in number of refinement targets and participating groups has been witnessed. Yet, protein structure refinement still remains a largely unsolved problem with majority of participating groups in CASP refinement category failed to consistently improve the quality of structures issued for refinement. In order to alleviate this need, we developed a completely automated and computationally efficient protein 3D structure refinement method, i3Drefine, based on an iterative and highly convergent energy minimization algorithm with a powerful all-atom composite physics and knowledge-based force fields and hydrogen bonding (HB) network optimization technique. In the recent community-wide blind experiment, CASP10, i3Drefine (as 'MULTICOM-CONSTRUCT') was ranked as the best method in the server section as per the official assessment of CASP10 experiment. Here we provide the community with free access to i3Drefine software and systematically analyse the performance of i3Drefine in strict blind mode on the refinement targets issued in CASP10 refinement category and compare with other state-of-the-art refinement methods participating in CASP10. Our analysis demonstrates that i3Drefine is only fully-automated server participating in CASP10 exhibiting consistent improvement over the initial structures in both global and local structural quality metrics. Executable version of i3Drefine is freely available at http://protein.rnet.missouri.edu/i3drefine/.

i3Drefine Software for Protein 3D Structure Refinement and Its Assessment in CASP10

Science.gov (United States)

Bhattacharya, Debswapna; Cheng, Jianlin

2013-01-01

Protein structure refinement refers to the process of improving the qualities of protein structures during structure modeling processes to bring them closer to their native states. Structure refinement has been drawing increasing attention in the community-wide Critical Assessment of techniques for Protein Structure prediction (CASP) experiments since its addition in 8th CASP experiment. During the 9th and recently concluded 10th CASP experiments, a consistent growth in number of refinement targets and participating groups has been witnessed. Yet, protein structure refinement still remains a largely unsolved problem with majority of participating groups in CASP refinement category failed to consistently improve the quality of structures issued for refinement. In order to alleviate this need, we developed a completely automated and computationally efficient protein 3D structure refinement method, i3Drefine, based on an iterative and highly convergent energy minimization algorithm with a powerful all-atom composite physics and knowledge-based force fields and hydrogen bonding (HB) network optimization technique. In the recent community-wide blind experiment, CASP10, i3Drefine (as ‘MULTICOM-CONSTRUCT’) was ranked as the best method in the server section as per the official assessment of CASP10 experiment. Here we provide the community with free access to i3Drefine software and systematically analyse the performance of i3Drefine in strict blind mode on the refinement targets issued in CASP10 refinement category and compare with other state-of-the-art refinement methods participating in CASP10. Our analysis demonstrates that i3Drefine is only fully-automated server participating in CASP10 exhibiting consistent improvement over the initial structures in both global and local structural quality metrics. Executable version of i3Drefine is freely available at http://protein.rnet.missouri.edu/i3drefine/. PMID:23894517

Refinement by interface instantiation

DEFF Research Database (Denmark)

Hallerstede, Stefan; Hoang, Thai Son

2012-01-01

be easily refined. Our first contribution hence is a proposal for a new construct called interface that encapsulates the external variables, along with a mechanism for interface instantiation. Using the new construct and mechanism, external variables can be refined consistently. Our second contribution...... is an approach for verifying the correctness of Event-B extensions using the supporting Rodin tool. We illustrate our approach by proving the correctness of interface instantiation....

Role of the process designer in the evolution of a technology oriented toward energy conservation

Energy Technology Data Exchange (ETDEWEB)

Cassarino, S [CONSER, Rome; Riccardi, R

1975-01-01

The increase in energy costs has introduced new stringent boundaries to process engineering, involving the need for more and more advanced calculation techniques and a greater accountability on the part of the process designer for the purposes of a financially effective engineering work. The designing and optimization approaches tending to favor minimum investment decisions for the past are now subjected to a careful critical revision under the pressures of this new reality. The process designer can--through such revision process--bring a substantial contribution of his own to the development of a technology oriented toward energy conservation. In view of these considerations and on the basis of newly emerging trends, some examples are introduced to illustrate certain development opportunities in oil-refining and petrochemical industrial processes. Conventional designs covering a refining plant and an oil fractionating unit are compared in details in this review with alternative patterns to which new designing approaches are applied for the purposes of an optimized energy consumption.

Investigation on grain refinement and precipitation strengthening applied in high speed wire rod containing vanadium

Energy Technology Data Exchange (ETDEWEB)

Wu, Da-yong; Xiao, Fu-ren, E-mail: frxiao@ysu.edu.cn; Wang, Bin; Liu, Jia-ling; Liao, Bo, E-mail: cyddjyjs@263.net

2014-01-13

To obtain necessary information for the simulation of high speed wire production process, the effect of grain refinement and precipitation strengthening on two high speed wire rod steels with different vanadium and nitrogen contents was investigated by continuous cooling transformation (CCT) characteristics. CCT curves were constructed by the dilatometer test and microscopic observation. Results showed that the formation of intra-granular ferrite (IGF) could refine grain remarkably and accelerate the ferrite transformation. Schedules for high speed wire production process focused on the effect of cooling rate. Ferrite grain was refined by increasing cooling rate and the formation of IGF. The microhardness calculation revealed that the steels were strengthened mostly by a combined effect of grain refinement and precipitation hardening. Degenerated pearlite was observed at lower transformation temperature and the fracture morphology changed from cementite lamellar to nanoscale cementite particle with increasing cooling rate. Based on the analysis above, an optimal schedule was applied and the microstructure and microhardness were improved.

[A Brief Homophobia Scale in Medical Students From Two Universities: Results of A Refinement Process].

Science.gov (United States)

Campo-Arias, Adalberto; Herazo, Edwin; Oviedo, Heidi Celina

The process of evaluating measurement scales is an ongoing procedure that requires revisions and adaptations according to the characteristics of the participants. The Homophobia Scale of seven items (EHF-7) has showed acceptable performance in medical students attending to two universities in Colombia. However, performance of some items was poor and could be removed, with an improvement in the psychometric findings of items retained. To review the psychometric functioning and refine the content of EHF-7 among medical students from two Colombian universities. A group of 667 students from the first to tenth semester participated in the research. Theirs ages were between 18 and 34 (mean, 20.9±2.7) years-old, and 60.6% were females. Cronbach alpha (α) and omega of McDonald (Ω) were calculated as indicators of reliability and to refine the scale, an exploratory (EFA) and confirmatory factor analysis (CFA) was performed. EHF-7 showed α=.793 and Ω=.796 and a main factor that explained 45.2% of the total variance. EFA and CFA suggested the suppression of three items. The four-item version (EHF-4) reached an α=.770 and Ω=.775, with a single factor that accounted for 59.7% of the total variance. CFA showed better indexes (χ 2 =3.622; df=1; P=.057; Root-mean-square error of approximation (RMSEA)=.063, 90% CI, .000-.130; Comparative Fit Indices (CFI)=.998; Tucker-Lewis Index (TLI)=.991). EHF-4 shows high internal consistency and a single dimension that explains more than 50% of the total variance. Further studies are needed to confirm these observations, that can be taken as preliminary. Copyright © 2016 Asociación Colombiana de Psiquiatría. Publicado por Elsevier España. All rights reserved.

Refining of the cracked products of mineral oils, etc

Energy Technology Data Exchange (ETDEWEB)

Seelig, S

1928-06-02

A process is disclosed for the refining of the distilled or cracked products from mineral oil, shale oil, or brown-coal-tar oil, with the aid of alkali-plumbite solution, characterized by adding to the plumbite solution from oxide, iron hydroxide, basic oxide, or an iron salt.

Analytical models of Ohmic heating and conventional heating in food processing

Science.gov (United States)

Serventi, A.; Bozzoli, F.; Rainieri, S.

2017-11-01

Ohmic heating is a food processing operation in which an electric current is passed through a food and the electrical resistance of the food causes the electric power to be transformed directly into heat. The heat is not delivered through a surface as in conventional heat exchangers but it is internally generated by Joule effect. Therefore, no temperature gradient is required and it origins quicker and more uniform heating within the food. On the other hand, it is associated with high energy costs and its use is limited to a particular range of food products with an appropriate electrical conductivity. Sterilization of foods by Ohmic heating has gained growing interest in the last few years. The aim of this study is to evaluate the benefits of Ohmic heating with respect to conventional heat exchangers under uniform wall temperature, a condition that is often present in industrial plants. This comparison is carried out by means of analytical models. The two different heating conditions are simulated under typical circumstances for the food industry. Particular attention is paid to the uniformity of the heat treatment and to the heating section length required in the two different conditions.

The relationship between viscosity and refinement efficiency of pure aluminum by Al-Ti-B refiner

Energy Technology Data Exchange (ETDEWEB)

Yu Lina [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, 73 Jingshi Road, Jinan 250061 (China); Liu Xiangfa [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, 73 Jingshi Road, Jinan 250061 (China)]. E-mail: xfliu@sdu.edu.cn

2006-11-30

The relationship between viscosity and refinement efficiency of pure aluminum with the addition of Al-Ti-B master alloy was studied in this paper. The experimental results show that when the grain size of solidified sample is finer the viscosity of the melt is higher after the addition of different Al-Ti-B master alloys. This indicates that viscosity can be used to approximately estimate the refinement efficiency of Al-Ti-B refiners in production to a certain extent. The main reason was also discussed in this paper by using transmission electron microscopy (TEM) analysis and differential scanning calorimetry (DSC) experiment.

Relational Demonic Fuzzy Refinement

OpenAIRE

Tchier, Fairouz

2014-01-01

We use relational algebra to define a refinement fuzzy order called demonic fuzzy refinement and also the associated fuzzy operators which are fuzzy demonic join $({\\bigsqcup }_{\\mathrm{\\text{f}}\\mathrm{\\text{u}}\\mathrm{\\text{z}}})$ , fuzzy demonic meet $({\\sqcap }_{\\mathrm{\\text{f}}\\mathrm{\\text{u}}\\mathrm{\\text{z}}})$ , and fuzzy demonic composition $({\\square }_{\\mathrm{\\text{f}}\\mathrm{\\text{u}}\\mathrm{\\text{z}}})$ . Our definitions and properties are illustrated by some examples using ma...

Rare earths refining by vacuum sublimation method

International Nuclear Information System (INIS)

Rytus, N.N.

1983-01-01

The process of rare earths refining by the sUblimation; method in high and superhigh oil-free vacuum, is investigated. The method is effective for rare earths obtaining and permits to prepare metal samples with a high value of electric resistance ratio γ=RsUb(298 K)/Rsub(4.2 K). The estimation of general purity is performed for Sm, Eu, Yb, Tm, Dy, Ho, Er and Se

Quality comparison of continuous steam sterilization segmented-flow aseptic processing versus conventional canning of whole and sliced mushrooms.

Science.gov (United States)

Anderson, N M; Walker, P N

2011-08-01

This study was carried out to investigate segmented-flow aseptic processing of particle foods. A pilot-scale continuous steam sterilization unit capable of producing shelf stable aseptically processed whole and sliced mushrooms was developed. The system utilized pressurized steam as the heating medium to achieve high temperature-short time processing conditions with high and uniform heat transfer that will enable static temperature penetration studies for process development. Segmented-flow technology produced a narrower residence time distribution than pipe-flow aseptic processing; thus, whole and sliced mushrooms were processed only as long as needed to achieve the target F₀  = 7.0 min and were not overcooked. Continuous steam sterilization segmented-flow aseptic processing produced shelf stable aseptically processed mushrooms of superior quality to conventionally canned mushrooms. When compared to conventionally canned mushrooms, aseptically processed yield (weight basis) increased 6.1% (SD = 2.9%) and 6.6% (SD = 2.2%), whiteness (L) improved 3.1% (SD = 1.9%) and 4.7% (SD = 0.7%), color difference (ΔE) improved 6.0% (SD = 1.3%) and 8.5% (SD = 1.5%), and texture improved 3.9% (SD = 1.7%) and 4.6% (SD = 4.2%), for whole and sliced mushrooms, respectively. Segmented-flow aseptic processing eliminated a separate blanching step, eliminated the unnecessary packaging of water and promoted the use of bag-in-box and other versatile aseptic packaging methods. Segmented-flow aseptic processing is capable of producing shelf stable aseptically processed particle foods of superior quality to a conventionally canned product. This unique continuous steam sterilization process eliminates the need for a separate blanching step, reduces or eliminates the need for a liquid carrier, and promotes the use of bag-in-box and other versatile aseptic packaging methods. © 2011 Institute of Food Technologists®

Assessment of very high-temperature reactors in process applications. Appendix II. VHTR process heat application studies

International Nuclear Information System (INIS)

Jones, J.E.; Gambill, W.R.; Cooper, R.H.; Fox, E.C.; Fuller, L.C.; Littlefield, C.C.; Silverman, M.D.

1977-06-01

A critical review is presented of the technology and economics for coupling a very high-temperature gas-cooled reactor to a variety of process applications. It is concluded that nuclear steam reforming of light hydrocarbons for coal conversion could be a near-term alternative and that direct nuclear coal gasification could be a future consideration. Thermochemical water splitting appears to be more costly and its availability farther in the future than the coal-conversion systems. Nuclear steelmaking is competitive with the direct reduction of iron ore from conventional coal-conversion processes but not competitive with the reforming of natural gas at present gas prices. Nuclear process heat for petroleum refining, even with the necessary backup systems, is competitive with fossil energy sources. The processing with nuclear heat of oil shale and tar sands is of marginal economic importance. An analysis of peaking power applications using nuclear heat was also made. It is concluded that steam reforming methane for energy storage and production of peaking power is not a viable economic alternative, but that energy storage with a high-temperature heat transfer salt (HTS) is competitive with conventional peaking systems. An examination of the materials required in process heat exchangers is made

Catalysts in petroleum refining and petrochemical industries 1995

Energy Technology Data Exchange (ETDEWEB)

Absi-Halabi, M.; Beshara, J.; Qabazard, H.; Stanislaus, A. [eds.] [Petroleum, Petrochemicals and Materials Division, Kuwait Institute of Scientific Research, Kuwait (Kuwait)

1996-07-01

Catalysis plays an increasingly critical role in modern petroleum refining and basic petrochemical industries. The market demands for and specifications of petroleum and petrochemical products are continuously changing. They have impacted the industry significantly over the past twenty years. Numerous new refining processes have been developed and significant improvements were made on existing technologies. Catalysts have been instrumental in enabling the industry to meet the continuous challenges posed by the market. As we enter the 21st century, new challenges for catalysis science and technology are anticipated in almost every field. Particularly, better utilization of petroleum resources and demands for cleaner transportation fuels are major items on the agenda. It is against this background that the 2nd International Conference on Catalysts in Petroleum Refining and Petrochemical Industries was organized. The papers from the conference were carefully selected from around 100 submissions. They were a mix of reviews providing an overview of selected areas, original fundamental research results, and industrial experiences. The papers in the proceedings were grouped in the following sections for quick reference: Plenary Papers; Hydroprocessing of Petroleum Residues and Distillates; Fluid Catalytic Cracking; Oxidation Catalysis; Aromatization and Polymerization Catalysis; Catalyst Characterization and Performance. The plenary papers were mostly reviews covering important topics related to the objectives of the conference. The remaining sections cover various topics of major impact on modern petroleum refining and petrochemical industries. A large number of papers dealt with hydroprocessing of petroleum distillates and residues which reflects the concern over meeting future sulfur-level specifications for diesel and fuel oils

Grain Refinement and Microstructural Evolution in Nickel During High-Pressure Torsion

National Research Council Canada - National Science Library

Zhilyaev, A

2002-01-01

.... It is now well established that SPD processing can lead to a very significant refinement in the size of a wide range of materials including pure metals, metallic alloys and intermetallics 3, 4...

Novel simple process for tocopherols selective recovery from vegetable oils by adsorption and desorption with an anion-exchange resin.

Science.gov (United States)

Hiromori, Kousuke; Shibasaki-Kitakawa, Naomi; Nakashima, Kazunori; Yonemoto, Toshikuni

2016-03-01

A novel and simple low-temperature process was used to recover tocopherols from a deodorizer distillate, which is a by-product of edible oil refining. The process consists of three operations: the esterification of free fatty acids with a cation-exchange resin catalyst, the adsorption of tocopherols onto an anion-exchange resin, and tocopherol desorption from the resin. No degradation of tocopherols occurred during these processes. In the tocopherol-rich fraction, no impurities such as sterols or glycerides were present. These impurities are commonly found in the product of the conventional process. This novel process improves the overall recovery ratio and the mass fraction of the product (75.9% and 51.0wt%) compared with those in the conventional process (50% and 35wt%). Copyright © 2015 Elsevier Ltd. All rights reserved.

Tri-Clustered Tensor Completion for Social-Aware Image Tag Refinement.

Science.gov (United States)

Tang, Jinhui; Shu, Xiangbo; Qi, Guo-Jun; Li, Zechao; Wang, Meng; Yan, Shuicheng; Jain, Ramesh

2017-08-01

Social image tag refinement, which aims to improve tag quality by automatically completing the missing tags and rectifying the noise-corrupted ones, is an essential component for social image search. Conventional approaches mainly focus on exploring the visual and tag information, without considering the user information, which often reveals important hints on the (in)correct tags of social images. Towards this end, we propose a novel tri-clustered tensor completion framework to collaboratively explore these three kinds of information to improve the performance of social image tag refinement. Specifically, the inter-relations among users, images and tags are modeled by a tensor, and the intra-relations between users, images and tags are explored by three regularizations respectively. To address the challenges of the super-sparse and large-scale tensor factorization that demands expensive computing and memory cost, we propose a novel tri-clustering method to divide the tensor into a certain number of sub-tensors by simultaneously clustering users, images and tags into a bunch of tri-clusters. And then we investigate two strategies to complete these sub-tensors by considering (in)dependence between the sub-tensors. Experimental results on a real-world social image database demonstrate the superiority of the proposed method compared with the state-of-the-art methods.

Panorama 2007: Refining and Petrochemicals

International Nuclear Information System (INIS)

Silva, C.

2007-01-01

The year 2005 saw a new improvement in refining margins that continued during the first three quarters of 2006. The restoration of margins in the last three years has allowed the refining sector to regain its profitability. In this context, the oil companies reported earnings for fiscal year 2005 that were up significantly compared to 2004, and the figures for the first half-year 2006 confirm this trend. Despite this favorable business environment, investments only saw a minimal increase in 2005 and the improvement expected for 2006 should remain fairly limited. Looking to 2010-2015, it would appear that the planned investment projects with the highest probability of reaching completion will be barely adequate to cover the increase in demand. Refining sector should continue to find itself under pressure. As for petrochemicals, despite a steady up-trend in the naphtha price, the restoration of margins consolidated a comeback that started in 2005. All in all, capital expenditure remained fairly low in both the refining and petrochemicals sectors, but many projects are planned for the next ten years. (author)

Recycling and refining of copper for electrical application

Directory of Open Access Journals (Sweden)

Dablement Sébastien

2013-11-01

Full Text Available Copper is, after silver, the best electrical conductor. All residual impurities inside the matrix have high consequences on these properties. Thus, the Nexans factory in Lens “purifies” the copper scraps by a fire refining in order to remove all the internal pollutant. This process, unique in France, is complementary to a traditional process using an electrolytic cathode. It allows, first, to diversify the raw material and, second, to increase the ecological balance compare to the traditional way of scrap treatment for electrical application.

Refining mass formulas for astrophysical applications: A Bayesian neural network approach

Science.gov (United States)

Utama, R.; Piekarewicz, J.

2017-10-01

Background: Exotic nuclei, particularly those near the drip lines, are at the core of one of the fundamental questions driving nuclear structure and astrophysics today: What are the limits of nuclear binding? Exotic nuclei play a critical role in both informing theoretical models as well as in our understanding of the origin of the heavy elements. Purpose: Our aim is to refine existing mass models through the training of an artificial neural network that will mitigate the large model discrepancies far away from stability. Methods: The basic paradigm of our two-pronged approach is an existing mass model that captures as much as possible of the underlying physics followed by the implementation of a Bayesian neural network (BNN) refinement to account for the missing physics. Bayesian inference is employed to determine the parameters of the neural network so that model predictions may be accompanied by theoretical uncertainties. Results: Despite the undeniable quality of the mass models adopted in this work, we observe a significant improvement (of about 40%) after the BNN refinement is implemented. Indeed, in the specific case of the Duflo-Zuker mass formula, we find that the rms deviation relative to experiment is reduced from σrms=0.503 MeV to σrms=0.286 MeV. These newly refined mass tables are used to map the neutron drip lines (or rather "drip bands") and to study a few critical r -process nuclei. Conclusions: The BNN approach is highly successful in refining the predictions of existing mass models. In particular, the large discrepancy displayed by the original "bare" models in regions where experimental data are unavailable is considerably quenched after the BNN refinement. This lends credence to our approach and has motivated us to publish refined mass tables that we trust will be helpful for future astrophysical applications.

Prevalent fatty acids in cashew nuts obtained from conventional and organic cultivation in different stages of processing

Directory of Open Access Journals (Sweden)

Denise Josino Soares

2013-06-01

Full Text Available Brazil is one of the three largest producers of fruits in the world, and among those fruit trees, the cashew tree stands out due to the high nutritional and commercial value of its products. During its fruit processing, there are losses in some compounds and few studies address this issue. Over the last decade the conventional system of food production has been substituted for the organic cultivation system, which is a promising alternative source of income given the global demand for healthy food. Therefore, this research aimed to characterize and quantify the prevalent fatty acids found in cashew nuts obtained from conventional and organic cultivation during various stages of processing. The prevalent fatty acids found were palmitic, linoleic, oleic, and stearic acid. The average of these fatty acids were 6.93 ± 0.55; 16.99 ± 0.61; 67.62 ± 1.00 and 8.42 ± 0.55 g/100 g, respectively. There was no reduction in the palmitic, oleic and stearic fatty acid contents during processing. Very little difference was observed between the nuts obtained from conventional and organic cultivation, indicating that the method of cultivation used has little or no influence on the content of cashew nut fatty acids.

Present status of refining and conversion facility dismantling. Progress in 2008 first half of the fiscal year

International Nuclear Information System (INIS)

Kado, Kazumi; Sugitsue, Noritake; Morimoto, Yasuyuki; Ikegami, Sohei; Takahashi, Nobuo; Tokuyasu, Takashi

2009-06-01

The Refining and Conversion Facility located in the Ningyo-toge Environmental Engineering Center. Process of natural uranium conversion facility (PNC Process) and reprocessed uranium conversion facility (two-stage dry fluorination system) is in a Refining and Conversion Facility. This building started construction in 1979 and was completed in October 1981. The PNC process operated from March 1982 to March 1991. As a result, uranium hexafluoride of about 385 tonU was manufactured. Also, the reprocessed uranium conversion process operated from December 1982 to July 1999. As a result, uranium hexafluoride of about 338 tonU was manufactured. The demonstration of the demolition method was done using the PNC process after the end of operation. The schedule which will finish dismantling of all equipment in a radiation controlled area is by the 2011 fiscal year. This report summarized the present situation by the first half of the 2008 fiscal year of a Refining and Conversion Facility decommissioning. (author)

Refining margins: recent trends

International Nuclear Information System (INIS)

Baudoin, C.; Favennec, J.P.

1999-01-01

Despite a business environment that was globally mediocre due primarily to the Asian crisis and to a mild winter in the northern hemisphere, the signs of improvement noted in the refining activity in 1996 were borne out in 1997. But the situation is not yet satisfactory in this sector: the low return on invested capital and the financing of environmental protection expenditure are giving cause for concern. In 1998, the drop in crude oil prices and the concomitant fall in petroleum product prices was ultimately rather favorable to margins. Two elements tended to put a damper on this relative optimism. First of all, margins continue to be extremely volatile and, secondly, the worsening of the economic and financial crisis observed during the summer made for a sharp decline in margins in all geographic regions, especially Asia. Since the beginning of 1999, refining margins are weak and utilization rates of refining capacities have decreased. (authors)

Panorama 2009 - refining

International Nuclear Information System (INIS)

2008-01-01

For oil companies to invest in new refining and conversion capacity, favorable conditions over time are required. In other words, refining margins must remain high and demand sustained over a long period. That was the situation prevailing before the onset of the financial crisis in the second half of 2008. The economic conjuncture has taken a substantial turn for the worse since then and the forecasts for 2009 do not look bright. Oil demand is expected to decrease in the OECD countries and to grow much more slowly in the emerging countries. It is anticipated that refining margins will fall in 2009 - in 2008, they slipped significantly in the United States - as a result of increasingly sluggish demand, especially for light products. The next few months will probably be unfavorable to investment. In addition to a gloomy business outlook, there may also be a problem of access to sources of financing. As for investment projects, a mainstream trend has emerged in the last few years: a shift away from the regions that have historically been most active (the OECD countries) towards certain emerging countries, mostly in Asia or the Middle East. The new conjuncture will probably not change this trend

Refining shale-oil distillates

Energy Technology Data Exchange (ETDEWEB)

Altpeter, J

1952-03-17

A process is described for refining distillates from shale oil, brown coal, tar, and other tar products by extraction with selective solvents, such as lower alcohols, halogen-hydrins, dichlorodiethyl ether, liquid sulfur dioxide, and so forth, as well as treating with alkali solution, characterized in that the distillate is first treated with completely or almost completely recovered phenol or cresotate solution, the oil is separated from the phenolate with solvent, for example concentrated or adjusted to a determined water content of lower alcohol, furfural, halogen-hydrin, dichlorodiethyl ether, liquid sulfur dioxide, or the like, extracted, and the raffinate separated from the extract layer, if necessary after distillation or washing out of solvent, and freeing with alkali solution from residual phenol or creosol.

A Game-Theoretic Approach to Branching Time Abstract-Check-Refine Process

Science.gov (United States)

Wang, Yi; Tamai, Tetsuo

2009-01-01

Since the complexity of software systems continues to grow, most engineers face two serious problems: the state space explosion problem and the problem of how to debug systems. In this paper, we propose a game-theoretic approach to full branching time model checking on three-valued semantics. The three-valued models and logics provide successful abstraction that overcomes the state space explosion problem. The game style model checking that generates counter-examples can guide refinement or identify validated formulas, which solves the system debugging problem. Furthermore, output of our game style method will give significant information to engineers in detecting where errors have occurred and what the causes of the errors are.

Preciscavanje otpadnih voda u postupcima prerade i flegmatizacije eksploziva / Refining of waste waters in processes of manufacturing and coating of high explosives

Directory of Open Access Journals (Sweden)

Mirjana Anđelković-Lukić

2002-03-01

Full Text Available U radu su prikazani tehnološki postupci prerade (flegmatizacije eksploziva pri kojima dolazi do zagađenja okoline otpadnim vodama. Prikazani su neki od načina prerade otpadnih voda pre nego što se ispuste u javne vodotokove. / The paper deals with production processes of manufacturing and coating Ugh explosives which pollute environment with waste waters. Some methods of refining waste waters before letting them into open water current are presented.

Separation of CsCl and SrCl_2 from a ternary CsCl-SrCl_2-LiCl via a zone refining process for waste salt minimization of pyroprocessing

International Nuclear Information System (INIS)

Shim, Moonsoo; Choi, Ho Gil; Yi, Kyung Woo; Hwang, Il Soon; Lee, Jong Hyeon

2016-01-01

The purification of LiCl salt mixture has traditionally been carried out by a melt crystallization process. To improve the throughput of zone refining, three heaters were installed in the zone refiner. The zone refining method was used to grow pure LiCl salt ingots from LiCl-CsCl-SrCl_2 salt mixture. The main investigated parameters were the heater speed and the number of passes. A change in the LiCl crystal grain size was observed according to the horizontal direction. From each zone refined salt ingot, samples were collected horizontally. To analyze the concentrations of Sr and Cs, an inductively coupled plasma optical emission spectrometer and inductively coupled plasma mass spectrometer were used, respectively. The experimental results show that Sr and Cs concentrations at the initial region of the ingot were low and reached their peak at the final freezing region of the salt ingot. Concentration results of zone refined salt were compared with theoretical results yielded by the proposed model to validate its predictions. The k_e_f_f of Sr and Cs were 0.13 and 0.11, respectively. The decontamination factors of Sr and Cs were 450 and 1650, respectively. - Highlights: • The LiCl-CsCl-SrCl_2 salt ingot was purified by zone refining technique to minimize waste salt. • The concentration distribution of Cs and Sr were analyzed by mass transfer equation. • The decontamination factors of Cs and Sr were 1600 and 450 respectively in case of 60% of recovery yield.

Romanian refining industry assesses restructuring

International Nuclear Information System (INIS)

Tanasescu, D.G.

1991-01-01

The Romanian crude oil refining industry, as all the other economic sectors, faces the problems accompanying the transition from a centrally planned economy to a market economy. At present, all refineries have registered as joint-stock companies and all are coordinated and assisted by Rafirom S.A., from both a legal and a production point of view. Rafirom S.A. is a joint-stock company that holds shares in refineries and other stock companies with activities related to oil refining. Such activities include technological research, development, design, transportation, storage, and domestic and foreign marketing. This article outlines the market forces that are expected to: drive rationalization and restructuring of refining operations and define the targets toward which the reconfigured refineries should strive

Comparison Between Conventional and Post-Processing PMU-Based State Estimation to Deal with Bad Data

DEFF Research Database (Denmark)

Khazraj, Hesam; Silva, Filipe Miguel Faria da; Bak, Claus Leth

2017-01-01

simulations, IEEE 30 bus is implemented in PowerFactory and Matlab is used to solve proposed state estimation using post-processing of PMUs. Bad data is generated manually and added in PMU and conventional measurements profile. Finally, the location and analysis of bad data are available by result of largest...

Production of biodiesel by transesterification of refined soybean oil ...

African Journals Online (AJOL)

This study focused on the production of biodiesel via transesterification of refined soybean oil obtained locally. Sodium hydroxide was used as the alkali catalyst and methanol (as alcohol) was used in the transesterification process due to its low cost. The methanol-to-oil molar ratio was maintained at 6:1. The effect of ...

Action Refinement

NARCIS (Netherlands)

Gorrieri, R.; Rensink, Arend; Bergstra, J.A.; Ponse, A.; Smolka, S.A.

2001-01-01

In this chapter, we give a comprehensive overview of the research results in the field of action refinement during the past 12 years. The different approaches that have been followed are outlined in detail and contrasted to each other in a uniform framework. We use two running examples to discuss

Validating neural-network refinements of nuclear mass models

Science.gov (United States)

Utama, R.; Piekarewicz, J.

2018-01-01

Background: Nuclear astrophysics centers on the role of nuclear physics in the cosmos. In particular, nuclear masses at the limits of stability are critical in the development of stellar structure and the origin of the elements. Purpose: We aim to test and validate the predictions of recently refined nuclear mass models against the newly published AME2016 compilation. Methods: The basic paradigm underlining the recently refined nuclear mass models is based on existing state-of-the-art models that are subsequently refined through the training of an artificial neural network. Bayesian inference is used to determine the parameters of the neural network so that statistical uncertainties are provided for all model predictions. Results: We observe a significant improvement in the Bayesian neural network (BNN) predictions relative to the corresponding "bare" models when compared to the nearly 50 new masses reported in the AME2016 compilation. Further, AME2016 estimates for the handful of impactful isotopes in the determination of r -process abundances are found to be in fairly good agreement with our theoretical predictions. Indeed, the BNN-improved Duflo-Zuker model predicts a root-mean-square deviation relative to experiment of σrms≃400 keV. Conclusions: Given the excellent performance of the BNN refinement in confronting the recently published AME2016 compilation, we are confident of its critical role in our quest for mass models of the highest quality. Moreover, as uncertainty quantification is at the core of the BNN approach, the improved mass models are in a unique position to identify those nuclei that will have the strongest impact in resolving some of the outstanding questions in nuclear astrophysics.

The hydrogen market in refining and petrochemicals in France

International Nuclear Information System (INIS)

Lutz, P.; Borel, P.

1991-11-01

The french hydrogen market on industrial sites can be divided into three main parts. Captive hydrogen is produced by thermofor catalytic reforming, catalytic cracking and hydrotreating of vacuum distillates, and is consumed in hydrotreating of petrol, hydrodesulfurization of gasoil and domestic fuel oil, hydrocracking and hydrofining of lubricants. By-product hydrogen is burnt in boilers and flare stacks. Merchant hydrogen is sold to users on the open market. Currently, thirteen refineries belonging to six companies produce 73 million tonnes of petroleum products each year in France and release annually a surplus of some 100,000 tonnes of hydrogen. The future of refining industry in France depends on the quality of the crude oil, the specific characteristics of the end products, and the developments in user markets. The refining process is likely to become more complex by 2005 with an increase in hydrogen requirements. Refineries could then undergo an annual deficit between 140,000 and 230,000 tonnes of hydrogen. The choice of the appropriate process to cover this shortfall depends mostly on oil companies strategy. (author). 1 fig., 3 tabs., 3 diagrams

Grain refining efficiency of Al-Ti-C alloys

International Nuclear Information System (INIS)

Birol, Yuecel

2006-01-01

The problems associated with boride agglomeration and the poisoning effect of Zr in Zr-bearing alloys have created a big demand for boron-free grain refiners. The potential benefits of TiC as a direct nucleant for aluminium grains have thus generated a great deal of interest in TiC-bearing alloys in recent years. In Al-Ti-C grain refiners commercially available today, Al 3 Ti particles are introduced into the melt along with the TiC particles. Since the latter are claimed to nucleate α-Al directly, it is of great technological interest to see if reducing the Ti:C ratio further, i.e., increasing the C content of the grain refiner, will produce an increase in the grain refining efficiency of these alloys. A series of grain refiner samples with the Ti concentration fixed at 3% and a range of C contents between 0 and 0.75 were obtained by appropriately mixing an experimental Al-3Ti-0.75C alloy with Al-10Ti alloy and commercial purity aluminium. The grain refining efficiency of these grain refiners was assessed to investigate the role of the insoluble TiC and the soluble Al 3 Ti particles. The optimum chemistry for the Al-Ti-C grain refiners was also identified

Grain refining efficiency of Al-Ti-C alloys

Energy Technology Data Exchange (ETDEWEB)

Birol, Yuecel [Materials Institute, Marmara Research Center, TUBITAK, 41470 Gebze, Kocaeli (Turkey)]. E-mail: yucel.birol@mam.gov.tr

2006-09-28

The problems associated with boride agglomeration and the poisoning effect of Zr in Zr-bearing alloys have created a big demand for boron-free grain refiners. The potential benefits of TiC as a direct nucleant for aluminium grains have thus generated a great deal of interest in TiC-bearing alloys in recent years. In Al-Ti-C grain refiners commercially available today, Al{sub 3}Ti particles are introduced into the melt along with the TiC particles. Since the latter are claimed to nucleate {alpha}-Al directly, it is of great technological interest to see if reducing the Ti:C ratio further, i.e., increasing the C content of the grain refiner, will produce an increase in the grain refining efficiency of these alloys. A series of grain refiner samples with the Ti concentration fixed at 3% and a range of C contents between 0 and 0.75 were obtained by appropriately mixing an experimental Al-3Ti-0.75C alloy with Al-10Ti alloy and commercial purity aluminium. The grain refining efficiency of these grain refiners was assessed to investigate the role of the insoluble TiC and the soluble Al{sub 3}Ti particles. The optimum chemistry for the Al-Ti-C grain refiners was also identified.

Adaptive temporal refinement in injection molding

Science.gov (United States)

Karyofylli, Violeta; Schmitz, Mauritius; Hopmann, Christian; Behr, Marek

2018-05-01

Mold filling is an injection molding stage of great significance, because many defects of the plastic components (e.g. weld lines, burrs or insufficient filling) can occur during this process step. Therefore, it plays an important role in determining the quality of the produced parts. Our goal is the temporal refinement in the vicinity of the evolving melt front, in the context of 4D simplex-type space-time grids [1, 2]. This novel discretization method has an inherent flexibility to employ completely unstructured meshes with varying levels of resolution both in spatial dimensions and in the time dimension, thus allowing the use of local time-stepping during the simulations. This can lead to a higher simulation precision, while preserving calculation efficiency. A 3D benchmark case, which concerns the filling of a plate-shaped geometry, is used for verifying our numerical approach [3]. The simulation results obtained with the fully unstructured space-time discretization are compared to those obtained with the standard space-time method and to Moldflow simulation results. This example also serves for providing reliable timing measurements and the efficiency aspects of the filling simulation of complex 3D molds while applying adaptive temporal refinement.

Characterization and process development for the selective removal of Sn, Sb, and As from anode slime obtained from electrolytic copper refining

Directory of Open Access Journals (Sweden)

Steinlechner S.

2018-01-01

Full Text Available The aim of this work was to develop a process for the removal of Sn, Sb and As from anode slime out of copper refinery to disburden a subsequent pyrometallurgical processing for precious metals refinement. For this reason, a detailed literature survey was conducted, followed by a characterization to find the present compounds/alloys and their morphology. A newly developed process concept for the separate extraction of the afore mentioned three target metals was developed and verified by leaching experiments, combined with thermodynamic calculations on their behavior under varying conditions. In this context, the influence of leaching temperature, alkalinity of leaching solution, and solid-liquid ration were evaluated on the extraction yields of Sn, As, and Sb, as well as how to exploit these findings to obtain separate streams enriched in the respective metals.

Data refinement for true concurrency

Directory of Open Access Journals (Sweden)

Brijesh Dongol

2013-05-01

Full Text Available The majority of modern systems exhibit sophisticated concurrent behaviour, where several system components modify and observe the system state with fine-grained atomicity. Many systems (e.g., multi-core processors, real-time controllers also exhibit truly concurrent behaviour, where multiple events can occur simultaneously. This paper presents data refinement defined in terms of an interval-based framework, which includes high-level operators that capture non-deterministic expression evaluation. By modifying the type of an interval, our theory may be specialised to cover data refinement of both discrete and continuous systems. We present an interval-based encoding of forward simulation, then prove that our forward simulation rule is sound with respect to our data refinement definition. A number of rules for decomposing forward simulation proofs over both sequential and parallel composition are developed.

Theoretical analysis of a biogas-fed PEMFC system with different hydrogen purifications: Conventional and membrane-based water gas shift processes

International Nuclear Information System (INIS)

Authayanun, Suthida; Aunsup, Pounyaporn; Patcharavorachot, Yaneeporn; Arpornwichanop, Amornchai

2014-01-01

Highlights: • Thermodynamic analysis of the biogas-fed PEMFC system is performed. • Conventional and membrane-based WGS processes for H 2 purification are studied. • A flowsheet model of the PEMFC system is developed. • Effect of key parameters on yields of H 2 and carbon in the biogas reformer is shown. • Performance of PEMFC systems with different H 2 purification processes is analyzed. - Abstract: This study presents a thermodynamic analysis of biogas reforming and proton electrolyte membrane fuel cell (PEMFC) integrated process with different hydrogen purifications: conventional and membrane-based water gas shift processes. The aim is to determine the optimal reforming process for hydrogen production from biogas in the PEMFC system. The formation of carbon is concerned in the hydrogen production. The simulation results show that increases in the steam-to-methane ratio and reformer temperature can improve the hydrogen yield and reduce the carbon formation. From the performance analysis, it is found that when the PEMFC is operated at high temperature and fuel utilization, the overall system efficiency enhances. The performance of the PEMFC system with the installation of a water gas shift membrane unit in the hydrogen purification step is slightly increased, compared with a conventional process

Grain refinement of permanent mold cast copper base alloys. Final report

Energy Technology Data Exchange (ETDEWEB)

Sadayappan, M.; Thomson, J. P.; Elboujdaini, M.; Gu, G. Ping; Sahoo, M.

2004-04-29

Grain refinement behavior of copper alloys cast in permanent molds was investigated. This is one of the least studied subjects in copper alloy castings. Grain refinement is not widely practiced for leaded copper alloys cast in sand molds. Aluminum bronzes and high strength yellow brasses, cast in sand and permanent molds, were usually fine grained due to the presence of more than 2% iron. Grain refinement of the most common permanent mold casting alloys, leaded yellow brass and its lead-free replacement EnviroBrass III, is not universally accepted due to the perceived problem of hard spots in finished castings and for the same reason these alloys contain very low amounts of iron. The yellow brasses and Cu-Si alloys are gaining popularity in North America due to their low lead content and amenability for permanent mold casting. These alloys are prone to hot tearing in permanent mold casting. Grain refinement is one of the solutions for reducing this problem. However, to use this technique it is necessary to understand the mechanism of grain refinement and other issues involved in the process. The following issues were studied during this three year project funded by the US Department of Energy and the copper casting industry: (1) Effect of alloying additions on the grain size of Cu-Zn alloys and their interaction with grain refiners; (2) Effect of two grain refining elements, boron and zirconium, on the grain size of four copper alloys, yellow brass, EnviroBrass II, silicon brass and silicon bronze and the duration of their effect (fading); (3) Prediction of grain refinement using cooling curve analysis and use of this method as an on-line quality control tool; (4) Hard spot formation in yellow brass and EnviroBrass due to grain refinement; (5) Corrosion resistance of the grain refined alloys; (6) Transfer the technology to permanent mold casting foundries; It was found that alloying elements such as tin and zinc do not change the grain size of Cu-Zn alloys

The petroleum refining industry and the implications for the environment

International Nuclear Information System (INIS)

Saraiva, Gerardo Jose de Pontes

2000-01-01

The petroleum refining industry is basically concerned with the production of oil, lubricants and intermediate petrochemical products, utilizing crude oil as its main raw material. Petroleum refining, a distillation process that breaks hydrocarbons into fractions, eliminating undesired impurities, generates irreducible residues. Until the industrial revolution, the residues were essentially organic, susceptible to the attack of agents of destruction and transformation (bacterium, fungi, etc). Suddenly, due to the intensification of human activities of modern man, nature scattered across the planet more resistant products, many of them with long life times, that produce a deeper impact in the environment. Almost entirely marine is the pollution that results from increasing quantity of hydrocarbons dumped into the sea, a problem that is aggravated by the development of manufacturing and transportation of petroleum products. The expansion of the petroleum commerce, using essentially maritime transportation, has increased considerably the probability of accidents increasing the risks of environment pollution. This work presents suggestions and possible solutions to minimize the problem of environment pollution, caused by refining and transportation of this combustible, essential to present time industry. (author)

Parallel Adaptive Mesh Refinement for High-Order Finite-Volume Schemes in Computational Fluid Dynamics

Science.gov (United States)

Schwing, Alan Michael

comparisons across a range of regimes. Unsteady and steady applications are considered in both subsonic and supersonic flows. Inviscid and viscous simulations achieve similar results at a much reduced cost when employing dynamic mesh adaptation. Several techniques for guiding adaptation are compared. Detailed analysis of statistics from the instrumented solver enable understanding of the costs associated with adaptation. Adaptive mesh refinement shows promise for the test cases presented here. It can be considerably faster than using conventional grids and provides accurate results. The procedures for adapting the grid are light-weight enough to not require significant computational time and yield significant reductions in grid size.

Steel refining possibilities in LF

Science.gov (United States)

Dumitru, M. G.; Ioana, A.; Constantin, N.; Ciobanu, F.; Pollifroni, M.

2018-01-01

This article presents the main possibilities for steel refining in Ladle Furnace (LF). These, are presented: steelmaking stages, steel refining through argon bottom stirring, online control of the bottom stirring, bottom stirring diagram during LF treatment of a heat, porous plug influence over the argon stirring, bottom stirring porous plug, analysis of porous plugs disposal on ladle bottom surface, bottom stirring simulation with ANSYS, bottom stirring simulation with Autodesk CFD.

Microstructures and constituents of super-high strength aluminum alloy ingots made through LFEC process

Directory of Open Access Journals (Sweden)

WANG Shuang

2007-11-01

Full Text Available Ingots of a new super-high strength Al-Zn-Mg-Cu-Zr alloy were produced respectively by low frequency electromagnetic casting (LFEC and by conventional direct chill (DC casting process. Microstructure and constituents of the ingots were studied. The results indicated that the LFEC process significantly refines microstructure and constituents of the alloy, and to some extent, decreases the area (or volume fraction of constituents and eutectic structure precipitated at grain boundaries. But, no difference in the type of constituents was observed between LFEC and DC ingots. The results also showed LFEC process can improve the as-cast mechanical properties.

Achieving aesthetic results in facial reconstructive microsurgery: planning and executing secondary refinements.

Science.gov (United States)

Haddock, Nicholas T; Saadeh, Pierre B; Siebert, John W

2012-12-01

Free tissue transfer to improve bulk and contour in facial deformities has been proven useful, yet refinements that turn an acceptable result into an excellent result are essential to reconstruction. The authors reviewed their experience and described these refinements. The charts of 371 free tissue transfer cases (1989 to 2010) performed by the senior author (J.W.S.) were reviewed. Free tissue transfer of a circumflex scapular variant flap or superficial inferior epigastric was performed to treat deformities arising from hemifacial atrophy (n = 126), hemifacial microsomia (n = 89), radiation therapy (n = 40), bilateral malformations including lupus and polymyositis (n = 50), other congenital anomalies (n = 25), facial palsy (n = 17), and burns and trauma (n = 24). Revision surgery planning began at initial flap operation where the flap was stretched maximally and interdigitated with recipient tissue. More tissue was required in the malar region. Revision refinement was indicated in all cases (after 6 months). Flap revision involved liposuction, debulking, reelevation, and release of tethering, followed by tissue rearrangement by means of advancement, rotation, transposition, and/or turnover flaps of subcutaneous tissues from the previous free flap. The jawline frequently required more debulking. Periorbital reconstruction was combined with lower lid support with or without canthal repositioning. Conventional face-lift techniques with the flap as superficial musculoaponeurotic system augmented the result. Autologous fat injection to the alar rim, medial canthus, upper eyelid, and lip was a useful adjunct. Severe lip deficiencies were addressed with local flaps. The keys to improving results were continual critical reassessment, open-mindedness to new approaches, and maintaining high expectations. Therapeutic, V.

Control and Prevention of Wastewater Pollution From Amerya Petroleum Refining Company

International Nuclear Information System (INIS)

Bakry, A.A.

2004-01-01

An oil refinery normally uses large quantities of water, for cooling and other process purpose. This water is treated from contaminants and finally returned to a lake or sea, outside the refinery. Amerya Petroleum Refining Company (APRC) uses conventional and special treatment methods for wastewater to remove all pollutants and to reduce the oil content in refinery final effluent water to a limit of 10 ppm , as the maximum permissible limit for environmental protection as designated by the Egyptian Act No.4 for the year 1994 . About 80% of oil in wastewater is separated by API (American Petroleum Institute) separator method and returned to refinery. Small oil droplets, emulsion and suspended matter escaped from API separator but were removed successfully in the dissolved air flotation (DAF) with chemical additives as the secondary treatment stage for wastewater. The flotation method with chemical additives and filtration were used to reduce the suspended solids and oil content to permissible levels (10 ppm) Furthermore, biological treatment unit was constructed to remove the dissolved oxygen consuming contaminates, e.g. phenolic compounds and traces of hydrocarbon derivatives. It was found that the BOD and COD of the effluent were reduced, and 100% removal of the trace amount of phenol was achieved in effluent

Method of cleansing and refining of liquid hydrocarbons and derivatives of hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Hahn, C A; Nielsen, H

1934-10-11

A process is described for cleaning and refining liquid hydrocarbons and derivatives by utilization of acids, followed by washing partly with a basic solution, partly with clean water. The process is characterized by using, in connection with the acid solutions mentioned, a strong solution of a mixture of sulfuric acid and phosphoric acid.

Refinement for Transition Systems with Responses

Directory of Open Access Journals (Sweden)

Marco Carbone

2012-07-01

Full Text Available Motivated by the response pattern for property specifications and applications within flexible workflow management systems, we report upon an initial study of modal and mixed transition systems in which the must transitions are interpreted as must eventually, and in which implementations can contain may behaviors that are resolved at run-time. We propose Transition Systems with Responses (TSRs as a suitable model for this study. We prove that TSRs correspond to a restricted class of mixed transition systems, which we refer to as the action-deterministic mixed transition systems. We show that TSRs allow for a natural definition of deadlocked and accepting states. We then transfer the standard definition of refinement for mixed transition systems to TSRs and prove that refinement does not preserve deadlock freedom. This leads to the proposal of safe refinements, which are those that preserve deadlock freedom. We exemplify the use of TSRs and (safe refinements on a small medication workflow.

Design of Grain Refiners for Aluminium Alloys

Science.gov (United States)

Tronche, A.; Greer, A. L.

The efficiency of a grain refiner can be quantified as the number of grains per nucleant particle in the solidified product. Even for effective refiners in aluminium, such as Al-5Ti-1B, it is known from experiments that efficiencies are very low, at best 10-3 to 102. It is of interest to explore the reasons for such low values, and to assess the prospects for increased efficiency though design of refiners. Recently it has been shown [1] that a simple recalescence-based model can make quantitative predictions of grain size as a function of refiner addition level, cooling rate and solute content. In the model, the initiation of grains is limited by the free growth from nucleant particles, the size distribution of which is very important. The present work uses this model as the basis for discussing the effect of particle size distribution on grain refiner performance. Larger particles (of TiB2 in the case of present interest) promote greater efficiency, as do narrower size distributions. It is shown that even if the size distribution could be exactly specified, compromises would have to be made to balance efficiency (defined as above) with other desirable characteristics of a refiner.

Mesh refinement for uncertainty quantification through model reduction

International Nuclear Information System (INIS)

Li, Jing; Stinis, Panos

2015-01-01

We present a novel way of deciding when and where to refine a mesh in probability space in order to facilitate uncertainty quantification in the presence of discontinuities in random space. A discontinuity in random space makes the application of generalized polynomial chaos expansion techniques prohibitively expensive. The reason is that for discontinuous problems, the expansion converges very slowly. An alternative to using higher terms in the expansion is to divide the random space in smaller elements where a lower degree polynomial is adequate to describe the randomness. In general, the partition of the random space is a dynamic process since some areas of the random space, particularly around the discontinuity, need more refinement than others as time evolves. In the current work we propose a way to decide when and where to refine the random space mesh based on the use of a reduced model. The idea is that a good reduced model can monitor accurately, within a random space element, the cascade of activity to higher degree terms in the chaos expansion. In turn, this facilitates the efficient allocation of computational sources to the areas of random space where they are more needed. For the Kraichnan–Orszag system, the prototypical system to study discontinuities in random space, we present theoretical results which show why the proposed method is sound and numerical results which corroborate the theory

A refinement methodology for object-oriented programs

OpenAIRE

Tafat , Asma; Boulmé , Sylvain; Marché , Claude

2010-01-01

International audience; Refinement is a well-known approach for developing correct-byconstruction software. It has been very successful for producing high quality code e.g., as implemented in the B tool. Yet, such refinement techniques are restricted in the sense that they forbid aliasing (and more generally sharing of data-structures), which often happens in usual programming languages. We propose a sound approach for refinement in presence of aliases. Suitable abstractions of programs are d...

Petroleum refining. 5, refinery operation and management; Le raffinage du petrole. 5. Exploitation et gestion de la raffinerie

Energy Technology Data Exchange (ETDEWEB)

Favennec, J.P. (ed.)

2001-07-01

In this volume, the reader will find: an analysis of the refining industry's current environment and economics, including the importance of crude oil, the demand for petroleum products, markets and price setting mechanisms for crude oil and oil products, refining costs and margins, the evolution of the refining capacity and of constraints on the industry; a review of the tools available for optimising and controlling operations; an explanation of material balance management and a description of refinery management and organisation. Contents: I. Background to refining. 1. Oil and Energy. 2. Petroleum products applications, characteristics, markets. 3. International oil markets. 4. Refining: a technical summary investments, margins, costs probable future developments. II. Refining tools. 5. Introduction to linear programming as used in the refining industry. 6. Application of linear programming to refining. 7. Automation, process control and information technology. 8. Applications and their implementation. III. Management and organisation. 9. Management and optimisation of refinery operations. 10. Logistics: transport and dispatch. 11. Functional and organisational analysis. 12. Managerial aspects. Glossary. Index. (author)

Consumer acceptance and aroma characterization of navy bean (Phaseolus vulgaris) powders prepared by extrusion and conventional processing methods.

Science.gov (United States)

Szczygiel, Edward J; Harte, Janice B; Strasburg, Gale M; Cho, Sungeun

2017-09-01

Food products produced with bean ingredients are gaining in popularity among consumers due to the reported health benefits. Navy bean (Phaseolus vulgaris) powder produced through extrusion can be considered as a resource-efficient alternative to conventional methods, which often involve high water inputs. Therefore, navy bean powders produced with extrusion and conventional methods were assessed for the impact of processing on consumer liking in end-use products and odor-active compounds. Consumer acceptance results reveal significant differences in flavor, texture and overall acceptance scores of several products produced with navy bean powder. Crackers produced with extruded navy bean powder received higher hedonic flavor ratings than those produced with commercial navy bean powder (P < 0.001). GC-O data showed that the commercial powder produced through conventional processing had much greater contents of several aliphatic aldehydes commonly formed via lipid oxidation, such as hexanal, octanal and nonanal with descriptors of 'grassy', 'nutty', 'fruity', 'dusty', and 'cleaner', compared to the extruded powder. Extrusion processed navy bean powders were preferred over commercial powders for certain navy bean powder applications. This is best explained by substantial differences in aroma profiles of the two powders that may have been caused by lipid oxidation. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

South Korea - oil refining overview

International Nuclear Information System (INIS)

Hayes, D.

1999-01-01

Following the economic problems of the 1990s, the petroleum refining industry of South Korea underwent much involuntary restructuring in 1999 with respect to takeovers and mergers and these are discussed. The demand for petroleum has now pretty well recovered. The reasons for fluctuating prices in the 1990s, how the new structure should be cushioned against changes in the future, and the potential for South Korea to export refined petroleum, are all discussed

Adaptive Mesh Refinement in CTH

International Nuclear Information System (INIS)

Crawford, David

1999-01-01

This paper reports progress on implementing a new capability of adaptive mesh refinement into the Eulerian multimaterial shock- physics code CTH. The adaptivity is block-based with refinement and unrefinement occurring in an isotropic 2:1 manner. The code is designed to run on serial, multiprocessor and massive parallel platforms. An approximate factor of three in memory and performance improvements over comparable resolution non-adaptive calculations has-been demonstrated for a number of problems

Price implications for Russia's oil refining

International Nuclear Information System (INIS)

Khartukov, Eugene M.

1998-01-01

Over the past several years, Russia's oil industry has undergone its radical transformation from a wholly state-run and generously subsidized oil distribution system toward a substantially privatized, cash-strapped, and quasi-market ''petropreneurship''. This fully applies to the industry's downstream sector. Still unlike more dynamic E and C operations, the country's refining has turned out better fenced off competitive market forces and is less capable to respond to market imperatives. Consequently, jammed between depressed product prices and persistent feedstock costs, Russian refiners were badly hit by the world oil glut - which has made a radical modernization of the obsolete refining sector clearly a must. (author)

Progress in vacuum metal extraction, refining and consolidation

International Nuclear Information System (INIS)

Sundaram, C.V.; Mukherjee, T.K.; Sharma, B.P.

1973-01-01

The unique achievements in the process metallurgy of rare metals in the past quarter century should largely be attributed to advances in vacuum technology. New standards for high purity, increasing demand for pure metals and alloys for established applications, and steady improvement in sophistication and capacity of vacuum furnaces have provided the stimulus for developing and expanding vacuum metal extraction processes, and also exploring totally new processes. The paper discusses the thermochemistry of vacuum metallurgy, carbothermic and metallothermic reduction reactions, consolidation and refining by vacuum arc melting, electron beam melting and high temperature high vacuum sintering, and ultrapurification, with special reference to the reactive and refractory metals of Group IV to VI. (author)

Effect of molybdenum addition on aluminium grain refined by titanium on its metallurgical and mechanical characteristics in the as cast condition and after pressing by the equal angular channel process

International Nuclear Information System (INIS)

Zaid, A. I. O.; Atieh, A. M.

2013-01-01

Aluminium and its alloys are versatile materials which are widely used in industrial and engineering applications due to their attractive characteristics. However, they solidify in columnar structure which tends to reduce their surface quality and mechanical strength. It is therefore, grain refined by grain refiners i.e. titanium or titanium+boron. The equal angular channel pressing, ECAP, process is a recent method for producing severe plastic deformation in materials. In this research work, the effect of addition of molybdenum either alone or in the presence of titanium to commercially pure aluminium on microstructure and mechanical behaviour is investigated in two conditions; first, in the as cast condition, and second after pressing by the ECAP process at room temperature. It was found that addition of Ti alone at a rate of 0.15 percentage weight to commercially pure Al resulted in grain refining of microstructure and a grain size of 91 meu m was obtained. However, after pressing by the ECAP process further refinement was achieved and the grain size was reduced to 18 meu m. Addition of Mo alone to aluminium at a rate of 0.1 percentage resulted in grain size of 76 meu m in the as cast condition and 32 meu m after pressing by the ECAP process. The combination of the two elements Ti and Mo together resulted in 48 meu m grain size in the as cast condition, compared to 40 meu m after pressing by the ECAP process. Furthermore, it was found that in the as cast condition: addition of Ti alone to Al resulted in enhancement of its mechanical behaviour by an increase of 5.2 percentage increase in its flow stress at 20 percentage true strain, whereas addition of Mo either alone or in the presence of Ti resulted in decrease of its flow stress at 20 percentage by 9 percentage and 5.6 percentage respectively. However, after pressing by ECAP: it was found that addition of Ti or Mo either alone or together to Al resulted in increase of its flow stress at 20 percentage strain by

Effect of molybdenum addition on aluminium grain refined by titanium on its metallurgical and mechanical characteristics in the as cast condition and after pressing by the equal angular channel process

International Nuclear Information System (INIS)

Zaid, A I O; Atieh, A M

2014-01-01

Aluminium and its alloys are versatile materials which are widely used in industrial and engineering applications due to their attractive characteristics. However, they solidify in columnar structure which tends to reduce their surface quality and mechanical strength. It is therefore, grain refined by grain refiners i.e. titanium or titanium+boron. The equal angular channel pressing, ECAP, process is a recent method for producing severe plastic deformation in materials. In this research work, the effect of addition of molybdenum either alone or in the presence of titanium to commercially pure aluminium on microstructure and mechanical behaviour is investigated in two conditions; first, in the as cast condition, and second after pressing by the ECAP process at room temperature. It was found that addition of Ti alone at a rate of 0.15% weight to commercially pure Al resulted in grain refining of microstructure and a grain size of 91μm was obtained. However, after pressing by the ECAP process further refinement was achieved and the grain size was reduced to 18μm. Addition of Mo alone to aluminium at a rate of 0.1% resulted in grain size of 76μm in the as cast condition and 32μm after pressing by the ECAP process. The combination of the two elements Ti and Mo together resulted in 48μm grain size in the as cast condition, compared to 40μm after pressing by the ECAP process. Furthermore, it was found that in the as cast condition: addition of Ti alone to Al resulted in enhancement of its mechanical behaviour by an increase of 5.2% increase in its flow stress at 20% true strain, whereas addition of Mo either alone or in the presence of Ti resulted in decrease of its flow stress at 20% by 9% and 5.6% respectively. However, after pressing by ECAP: it was found that addition of Ti or Mo either alone or together to Al resulted in increase of its flow stress at 20 % strain by the following percentages 5.49, 4.74 and 10.3% respectively

Technology of niobium and molybdenum refining by electron beam

International Nuclear Information System (INIS)

Conti, R.A.; Pinatti, D.G.; Sandim, H.R.Z.

1988-01-01

The uses of metals and alloys in superconductors (Nb46%Ti), aerospatial industry (Ti6Al4V), electroeletronic industry (Nb, Mo, W) and in surgical implants (Ti, Nb) are increasing nowadays. A refining process of niobium and molybdenum by electron beam technique, since the oxides reduction till the obtention of a high purity ingot is presented. (C.G.C.) [pt

Development of reduced crude processing technology in delayed coking units; Desenvolvimento da tecnologia de processamento de residuo atmosferico em unidade de coqueamento retardado

Energy Technology Data Exchange (ETDEWEB)

Soares, Gloria Maria Gomes; Bartros, Francisco Carlos da Costa; Goncalves, Natalie Jorge; Pala, Danielle Marins; Nadolni, Aline Voigt [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2008-07-01

Delayed Coking Technology can be described as thermal cracking of low value refinery residual streams into high-value products. This process has been applied in petroleum refining schemes in order to upgrade heavy and ultra-heavy crude oils. The typical feedstock is vacuum residue (VR). When we have an increasing medium distillates demand and refining schemes which have gas oil and VR excess, the simultaneous conversion of these streams becomes economically attractive, due mainly to the increase of diesel production. Thus, the processing of atmospheric residue (AR) in Delayed Coking Units (DCU) has fueled great interest for PETROBRAS. This work presents the results of industrial and pilot plant tests with AR and VR showing the increasing of diesel yields and decreasing of coke yields processing AR as feedstock. When we process all the AR in the DCU with high recycle rate we observe an increasing of 25% on refinery diesel production related to conventional schemes. The refining scheme of the new PETROBRAS refinery at Northeast of Brazil is based on this technology. This refinery will process heavy oils maximizing diesel production with minimum investment. (author)

Grain refinement mechanism in A3003 alloy

International Nuclear Information System (INIS)

Cho, Hoon; Shin, Je-Sik; Lee, Byoung-Soo; Jo, Hyung-Ho

2009-01-01

In the present study, in order to find out an grain refinement mechanism, 0.1wt.% Al-10wt.%Ti master alloy was added into A3003 alloy melt contained in graphite crucible and in alumina crucible, and then the melt holding time at 750 deg. C was systematically changed from 1 min up to 120 min. It is interesting to note that the grain refinement and fading phenomena remarkably depend on the crucible material. The fading effect in the specimens using alumina crucible can be explained as the result of TiAl 3 phase dissolution into molten aluminium matrix. In the specimens using graphite crucible, the grain refinement was occurred gradually with increasing holding time. It was suggest that the continuous grain refinement is due to transition of refinement mechanism from TiAl 3 phase to TiC phase. It can be mentioned that the TiC formed from titanium and carbon solute in the aluminium melt, which came from the Al-10Ti alloy and the graphite crucible.

Startup of the Anammox Process in a Membrane Bioreactor (AnMBR) from Conventional Activated Sludge.

Science.gov (United States)

Gutwiński, P; Cema, G; Ziembińska-Buczyńska, A; Surmacz-Górska, J; Osadnik, M

2016-12-01

  In this study, a laboratory-scale anammox process in a membrane bioreactor (AnMBR) was used to startup the anaerobic ammonium oxidation (anammox) process from conventional activated sludge. Stable operation was achieved after 125 days. From that time, nitrogen load was gradually increased. After six months, the average nitrogen removal efficiency exceeded 80%. The highest obtained special anammox activity (SAA) achieved was 0.17 g (-N + -N) (g VSS × d)-1. Fluorescent in situ hybridization also proved the presence of the anammox bacteria, typically a genus of Brocadia anammoxidans and Kuenenia stuttgartiensis.

China expands refining sector to handle booming oil demand

International Nuclear Information System (INIS)

Anon.

1993-01-01

China's refining sector is in the midst of a major expansion and reorganization in response to booming domestic demand for petroleum products. Plans call for hiking crude processing capacity to 3.9 million b/d in 1995 from the current 3.085 million b/d. Much of that 26% increase will come where the products demand growth is the strongest: China's coastal provinces, notably those in the southeast. Despite the demand surge, China's refineries operated at only 74% of capacity in 1991, and projections for 1992 weren't much better. Domestic crude supply is limited because of Beijing's insistence on maintaining crude export levels, a major source of hard currency foreign exchange. The paper discusses the superheated demand; exports and imports; the refining infrastructure; the Shenzhen refinery; Hong Kong demand; southeast coast demand; 1993 plans; and foreign investment

Refining discordant gene trees.

Science.gov (United States)

Górecki, Pawel; Eulenstein, Oliver

2014-01-01

Evolutionary studies are complicated by discordance between gene trees and the species tree in which they evolved. Dealing with discordant trees often relies on comparison costs between gene and species trees, including the well-established Robinson-Foulds, gene duplication, and deep coalescence costs. While these costs have provided credible results for binary rooted gene trees, corresponding cost definitions for non-binary unrooted gene trees, which are frequently occurring in practice, are challenged by biological realism. We propose a natural extension of the well-established costs for comparing unrooted and non-binary gene trees with rooted binary species trees using a binary refinement model. For the duplication cost we describe an efficient algorithm that is based on a linear time reduction and also computes an optimal rooted binary refinement of the given gene tree. Finally, we show that similar reductions lead to solutions for computing the deep coalescence and the Robinson-Foulds costs. Our binary refinement of Robinson-Foulds, gene duplication, and deep coalescence costs for unrooted and non-binary gene trees together with the linear time reductions provided here for computing these costs significantly extends the range of trees that can be incorporated into approaches dealing with discordance.

Dense and refined microstructure 3D measurement method based on an optical microscope and varying illuminations

International Nuclear Information System (INIS)

Li, Zhongwei; Li, Y F

2011-01-01

We propose a novel microscopic photometric stereo (MPS) method based on a conventional optical microscope and varying illuminations for dense and refined microstructure 3D measurement. To guarantee the flexibility of the MPS, an uncalibrated photometric stereo (UPS) method, which does not require a priori knowledge of the light-source direction or the light-source intensity, is employed to recover surface normals and albedos from the captured multiple micro-images. Although the UPS has been studied before, there are some particular issues to be addressed to make it suitable for microscopic cases. For resolving the inherent generalized bas-relief (GBR) ambiguity of the UPS, we present a GBR disambiguation method based on a framework of entropy minimization, and extend it using a graph-cut energy minimization to decrease the influence of noise and further refine the recovered surface normal. The proposed MPS method has been tested on synthetic as well as real images and very encouraging results have been obtained. The experimental results show that this novel method can reconstruct dense and refined 3D points for the microstructure. It is an easy-to-implement yet effective alternative method for microstructure 3D measurement and can be applied to many potential fields

Phenolic content and antioxidant capacity in organically and conventionally grown eggplant (Solanum melongena fruits following thermal processing

Directory of Open Access Journals (Sweden)

Erika Leonor Zambrano-Moreno

2015-09-01

Full Text Available AbstractThermal processing and production practices used in vegetables can cause changes in their phytochemical contents. Eggplant is characterized by its high antioxidant content. The objective of this work was to determine levels of anthocyanins, polyphenols, and flavonoids and antioxidant capacity in organically and conventionally grown eggplant prepared fresh or subjected to one of three thermal preparation methods: boiling, baking or steaming. The soluble and hydrolyzable polyphenols and flavonoids content were quantified by Folin-Ciocalteu and Aluminum chloride methods, respectively. Anthocyanins were quantified according to the pH differential method. Antioxidant capacity was determined by DPPH and ORAC methods. The results showed differences between organic and conventional eggplant for some variables although cultivation method did not have a consistent effect. Hydrolysable polyphenol content was greater, and soluble and hydrolysable antioxidant capacities were higher in organically grown eggplant, while anthocyanin content was greater in conventionally grown eggplant. Fresh eggplant produced under conventional cultivation had a much greater content of anthocyanins compared to that of other cultivation method-thermal treatment combination. In general, steamed eggplant contained higher total polyphenol and flavonoid levels as well as greater antioxidant capacity. Steamed eggplant from both conventional and organic systems also had high amounts of anthocyanins compared to other thermal treatments.

The use of Fourier reverse transforms in crystallographic phase refinement

Energy Technology Data Exchange (ETDEWEB)

Ringrose, Sharon [Iowa State Univ., Ames, IA (United States)

1997-10-08

Often a crystallographer obtains an electron density map which shows only part of the structure. In such cases, the phasing of the trial model is poor enough that the electron density map may show peaks in some of the atomic positions, but other atomic positions are not visible. There may also be extraneous peaks present which are not due to atomic positions. A method for determination of crystal structures that have resisted solution through normal crystallographic methods has been developed. PHASER is a series of FORTRAN programs which aids in the structure solution of poorly phased electron density maps by refining the crystallographic phases. It facilitates the refinement of such poorly phased electron density maps for difficult structures which might otherwise not be solvable. The trial model, which serves as the starting point for the phase refinement, may be acquired by several routes such as direct methods or Patterson methods. Modifications are made to the reverse transform process based on several assumptions. First, the starting electron density map is modified based on the fact that physically the electron density map must be non-negative at all points. In practice a small positive cutoff is used. A reverse Fourier transform is computed based on the modified electron density map. Secondly, the authors assume that a better electron density map will result by using the observed magnitudes of the structure factors combined with the phases calculated in the reverse transform. After convergence has been reached, more atomic positions and less extraneous peaks are observed in the refined electron density map. The starting model need not be very large to achieve success with PHASER; successful phase refinement has been achieved with a starting model that consists of only 5% of the total scattering power of the full molecule. The second part of the thesis discusses three crystal structure determinations.

Distillation modeling for a uranium refining process

Energy Technology Data Exchange (ETDEWEB)

Westphal, B.R.

1996-03-01

As part of the spent fuel treatment program at Argonne National Laboratory, a vacuum distillation process is being employed for the recovery of uranium following an electrorefining process. Distillation of a salt electrolyte, containing a eutectic mixture of lithium and potassium chlorides, from uranium is achieved by a simple batch operation and is termed {open_quotes}cathode processing{close_quotes}. The incremental distillation of electrolyte salt will be modeled by an equilibrium expression and on a molecular basis since the operation is conducted under moderate vacuum conditions. As processing continues, the two models will be compared and analyzed for correlation with actual operating results. Possible factors that may contribute to aberrations from the models include impurities at the vapor-liquid boundary, distillate reflux, anomalous pressure gradients, and mass transport phenomena at the evaporating surface. Ultimately, the purpose of either process model is to enable the parametric optimization of the process.

Separation of CsCl and SrCl{sub 2} from a ternary CsCl-SrCl{sub 2}-LiCl via a zone refining process for waste salt minimization of pyroprocessing

Energy Technology Data Exchange (ETDEWEB)

Shim, Moonsoo [Graduate School of Energy Science and Technology, Chungnam National University, 99 Daehak-ro, Yuseong-gu, Daejeon, 34134 (Korea, Republic of); Choi, Ho Gil; Yi, Kyung Woo; Hwang, Il Soon [Graduate School of Seoul National University, 1 Gwanak-ro, Gwanak-gu, Seoul 08826 (Korea, Republic of); Lee, Jong Hyeon, E-mail: jonglee@cnu.ac.kr [Graduate School of Energy Science and Technology, Chungnam National University, 99 Daehak-ro, Yuseong-gu, Daejeon, 34134 (Korea, Republic of); Graduate School of Department of Advanced Materials Engineering, Chungnam National University, 99 Daehak-ro, Yuseong-gu, Daejeon, 34134 (Korea, Republic of); Rapid Solidified Materials Research Center, Chungnam National University, 99 Daehak-ro, Yuseong-gu, Daejeon, 34134 (Korea, Republic of)

2016-11-15

The purification of LiCl salt mixture has traditionally been carried out by a melt crystallization process. To improve the throughput of zone refining, three heaters were installed in the zone refiner. The zone refining method was used to grow pure LiCl salt ingots from LiCl-CsCl-SrCl{sub 2} salt mixture. The main investigated parameters were the heater speed and the number of passes. A change in the LiCl crystal grain size was observed according to the horizontal direction. From each zone refined salt ingot, samples were collected horizontally. To analyze the concentrations of Sr and Cs, an inductively coupled plasma optical emission spectrometer and inductively coupled plasma mass spectrometer were used, respectively. The experimental results show that Sr and Cs concentrations at the initial region of the ingot were low and reached their peak at the final freezing region of the salt ingot. Concentration results of zone refined salt were compared with theoretical results yielded by the proposed model to validate its predictions. The k{sub eff} of Sr and Cs were 0.13 and 0.11, respectively. The decontamination factors of Sr and Cs were 450 and 1650, respectively. - Highlights: • The LiCl-CsCl-SrCl{sub 2} salt ingot was purified by zone refining technique to minimize waste salt. • The concentration distribution of Cs and Sr were analyzed by mass transfer equation. • The decontamination factors of Cs and Sr were 1600 and 450 respectively in case of 60% of recovery yield.

Refined large N duality for knots

DEFF Research Database (Denmark)

Kameyama, Masaya; Nawata, Satoshi

We formulate large N duality of U(N) refined Chern-Simons theory with a torus knot/link in S³. By studying refined BPS states in M-theory, we provide the explicit form of low-energy effective actions of Type IIA string theory with D4-branes on the Ω-background. This form enables us to relate...

US refining reviewed

International Nuclear Information System (INIS)

Yamaguchi, N.D.

1998-01-01

The paper reviews the history, present position and future prospects of the petroleum industry in the USA. The main focus is on supply and demand, the high quality of the products, refinery capacity and product trade balances. Diagrams show historical trends in output, product demand, demand for transport fuels and oil, refinery capacity, refinery closures, and imports and exports. Some particularly salient points brought out were (i) production of US crude shows a marked downward trend but imports of crude will continue to increase, (ii) product demand will continue to grow even though the levels are already high, (iii) the demand is dominated by those products that typically yield the highest income for the refiner, (i.e. high quality transport fuels for environmental compliance), (iv) refinery capacity has decreased since 1980 and (v) refining will continue to have financial problems but will still be profitable. (UK)

Mechanical Behaviour of Conventional Materials at Experimental Conditions of Deep Drawing Technological Process

Science.gov (United States)

Nikolov, N.; Pashkouleva, D.; Kavardzhikov, V.

2012-09-01

The paper deals with experimental investigations on the mechanical behaviour of body-centred-cubic (BCC) and face-centred-cubic (FCC)-conventionally structured sheet metalic-metalic materials under stress-strain conditions of a deep drawing process determined by a coefficient close to the limiting one for Steel 08 and punch diameter of 50 mm. The mechanical characteristics of the investigated materials are identified by one-dimensional tension tests. The materials' responses, as results of identical loading conditions, are described by the change of blank sizes and characteristics of the forming processes. The chosen deformation path ensures obtaining a qualitative steel piece and leads to failures of aluminium and brass blanks. The reported results could be useful for investigations and predictions of the mechanical responses of such type metallic structures applying microscopic instrumented observations and numerical simulations.

Impact of Crude Oil Quality on the Refining Conditions and Composition of Nutraceuticals in Refined Palm Oil.

Science.gov (United States)

Sampaio, Klicia A; Ayala, Jose Vila; Van Hoed, Vera; Monteiro, Simone; Ceriani, Roberta; Verhé, Roland; Meirelles, Antonio J A

2017-08-01

Palm oil is the major vegetable oil used worldwide due to its unique properties. The effect of crude palm oil acidity on the final free fatty acids (FFA) content, neutral oil loss (NOL), and nutraceutical compounds, such as carotenes, total tocols (tocopherols and tocotrienols), squalene, and phytosterols was investigated. A central composite design was employed to study the influence of the refining conditions: temperature (200 to 260 °C), steam percentage (0.5% to 3.5%), and initial FFA content (2.2% to 6.0%) on the quality of the refined product. The results revealed that initial palm oil acidity is a statistically important parameter to obtain commercially acceptable values for final FFA content. The increase of temperature presented the most important effect on the reduction of all nutraceutical compounds. The highest tocopherols (88%), phytosterols (98%), and squalene retention (84%) was obtained when applying the mildest temperature (200 °C). From the experimental results, 3 equations were generated enabling the prediction of the free fatty acids content, the tocols content, and the losses of neutral oil. Therefore, this work contributes to the understanding and optimization of the process for the production of palm oil with high nutraceutical quality and low free fatty acid contents. © 2017 Institute of Food Technologists®.

Neutrosophic Refined Similarity Measure Based on Cosine Function

Directory of Open Access Journals (Sweden)

Said Broumi

2014-12-01

Full Text Available In this paper, the cosine similarity measure of neutrosophic refined (multi- sets is proposed and its properties are studied. The concept of this cosine similarity measure of neutrosophic refined sets is the extension of improved cosine similarity measure of single valued neutrosophic. Finally, using this cosine similarity measure of neutrosophic refined set, the application of medical diagnosis is presented.

Future of French refining

International Nuclear Information System (INIS)

Calvet, B.

1993-01-01

Over recent years, the refining industry has had to grapple with a growing burden of environmental and safety regulations concerning not only its plants and other facilities, but also its end products. At the same time, it has had to bear the effects of the reduction of the special status that used to apply to petroleum, and the consequences of economic freedom, to which we should add, as specifically concerns the French market, the impact of energy policy and the pro-nuclear option. The result is a drop in heavy fuel oil from 36 million tonnes per year in 1973 to 6.3 million in 1992, and in home-heating fuel from 37 to 18 million per year. This fast-moving market is highly competitive. The French market in particular is wide open to imports, but the refining companies are still heavy exporters for those products with high added-value, like lubricants, jet fuel, and lead-free gasolines. The competition has led the refining companies to commit themselves to quality, and to publicize their efforts in this direction. This is why the long-term perspectives for petroleum fuels are still wide open. This is supported by the probable expectation that the goal of economic efficiency is likely to soften the effects of the energy policy, which penalizes petroleum products, in that they have now become competitive again. In the European context, with the challenge of environmental protection and the decline in heavy fuel outlets, French refining has to keep on improving the quality of its products and plants, which means major investments. The industry absolutely must return to a more normal level of profitability, in order to sustain this financial effort, and generate the prosperity of its high-performance plants and equipment. 1 fig., 5 tabs

The evolution of oil refining in Europe

Energy Technology Data Exchange (ETDEWEB)

Reid, A. [CONCAWE, Brussels (Belgium)

2013-04-01

Back in 1963 when CONCAWE was founded, the world looked very different from what it is today, and so did the global and European refining industry. Oil product markets were expanding fast and new refineries were being built at a steady rate. The oil crisis of the 1970s brought an abrupt end to this, heralding a long era of consolidation and stepwise adaptation. At the same time the nature of the global oil business shifted from fully integrated companies producing, transporting and refining their own oil to a much more diversified situation where oil production ('upstream') and refining/distribution ('downstream') gradually became two essentially separate businesses. From being purely a 'cost centre' in an integrated chain, refining has become a separate activity in its own right, operating as a 'profit centre' between two global markets - crude oil and products - which, although not entirely independent, have their own dynamics and influences. In addition demand gradually shifted towards lighter products while the quality requirements on all products were considerably tightened. This article explores the new challenges that these changes have imposed on EU refiners, and describes CONCAWE's contributions to understanding their impact on refinery production and investments.

Russian refining shows signs of revival, needs investment

International Nuclear Information System (INIS)

Plotnikov, V.S.; Avgerinos, G.F.; Dvorets, N.L.; Tyukov, V.M.

1996-01-01

The Russian refining industry appears ready for a comeback but needs investment from abroad. After 7 years of annual decline, output of petroleum products in the former Soviet Union (FSU), most of it from Russian refineries, is estimated to have dropped marginally last year. And an increase is possible this year. In 1994, Russia's refineries, which account for two thirds of total FSU distillation capacity, yielded 176.2 million metric tons of oil products, compared with 214.1 million tons in 1993. Despite the precipitous decline in refinery production, net FSU exports oil refined products were down only 5% in 1994 at about 51.3 million tons. This occurred despite the decline in refinery production because of sizable contraction in oil consumption in Russian and the other republics. Russia, like the rest of the FSU, needs more than loans to produce oil or restore wells. According to the Ministries of Economics and Fuels and Energy, 90% of Russian enterprises need foreign capital. Investments to rebuild refining, gas processing, and petrochemicals are necessary, as are funds for modern technologies and equipment. Capital also is needed for extraction of resources that are remotely located or difficult to produce. In addition to providing a legal structure that provides a solid basis for investment, Russian must promote competition, change its tax system to raise revenue but allow companies to retain profits, and remove disincentives to investment for domestic and foreign enterprises

The potential impact of proposed hazardous air pollutant legislation on the US refining industry

International Nuclear Information System (INIS)

1989-11-01

The Administration has recently submitted a Clean Air Act Bill to Congress which would significantly modify the regulatory treatment of industrial hazardous air pollutants (air toxics). The adverse economic impacts of this legislation on the petroleum refining industry could be substantial. Depending on how EPA interprets the legislative language, the capital costs of compliance for the proposed bill could range from $1.3 to $15.0 billion. At the upper end of the range, costs of this order of magnitude would be over 2.5 times larger than the combined estimated cost of EPAs gasoline volatility (RVP) regulations and the proposed diesel sulfur content regulations. Potential compliance costs could be as much as $0.40 per barrel processed for large, complex refineries and as much as $0.50 per barrel for some small, simple refineries. For perspective, total refining costs, including a normal return on investment, are $4--5 per barrel. Because foreign refineries supplying the US will not be affected by the US air toxics regulations, US refineries may not be able to raise prices sufficiently to recover their compliance costs. For this reason, the air toxic legislation may put US refineries at an economic disadvantage relative to foreign competitors. Even under the best petroleum product market conditions, costs of $0.40 to $0.50 per barrel processed could reduce US Gulf refiner cash operating margins by as much as 29 percent. Under less favorable market conditions, such as the mid-80's when refiners were losing money, the hazardous air pollutant regulations could greatly increase US refiner operating losses and potentially lead to closure of some marginal refineries

Application of the Aarhus Convention

Directory of Open Access Journals (Sweden)

Tubić Bojan

2011-01-01

Full Text Available Convention on access to information, public participation in decision-making and access to justice in environmental matters (Aarhus Convention has been adopted in 1998 and entered into force three years later. It envisages three elements for strengthening democratic procedures in decision-making: access to information, public participation and access to justice. At the first meeting of the Member States the Aarhus Convention Compliance Committee was founded. The European Union is a party of the Convention and it has implemented the provisions in its legal order. After entering into force of the Convention, several Directives that regulate these issues in the EU have been enacted. Republic of Serbia has ratified the Convention in 2009 and it is currently in the process of its implementation by involving private subjects in decision-making on environmental issues.

Canada's hydrocarbon processing evolution

International Nuclear Information System (INIS)

Wise, T.H.; Horton, R.

2000-01-01

The development of petroleum refining, petrochemicals and natural gas industries in Canada are discussed together with future issues and prospects. Figures give data on (a) refined products trade 1998; (b) refining capacity; (c) product demand 1980-1999; (d) refinery crude runs and capacity; (e) refining and marketing, historical returns 1993-1999; (f) processing power index for Canada and USA; (g) ethylene capacity; (eye) Montreal petrochemical capacities; (j) Sarnia petrochemical capacities in 2000; (k) Alberta petrochemicals capacities 2001; (l) ethylene net equivalent trade; (m) ethylene costs 1999 for W. Canada and other countries. It was concluded that the hydrocarbon processing business continues to expand in Canada and natural gas processing is likely to increase. Petrochemicals may expand in W. Canada, possibly using feed stock from the Far North. Offshore developments may stimulate new processing on the E. Coast

Refinery production planning and scheduling: the refining core business

Directory of Open Access Journals (Sweden)

M. Joly

2012-06-01

Full Text Available Intelligent production planning and scheduling are of paramount importance to ensure refinery profitability, logistic reliability and safety at the local and corporate levels. In Brazil, such activities play a particularly critical role, since the Brazilian downstream model is moving towards a demand-driven model rather than a supply-driven one. Moreover, new and specialized non-linear constraints are continuously being incorporated into these large-scale problems: increases in oil prices implying the need for processing poor quality crudes, increasing demand and new demand patterns for petroleum products, new stringent environmental regulations related to clean fuels and start-up of new production technologies embedded into more complex refining schemes. This paper aims at clarifying the central role of refinery planning and scheduling activities in the Petrobras refining business. Major past and present results are outlined and corporate long-term strategies to deal with present and future challenges are presented.

Refining's-clean new jingle

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that at a time when profit margins are slim and gasoline demand is down, the U.S. petroleum-refining industry is facing one of its greatest challenges; How to meet new federal and state laws for reformulated gasoline, oxygenated fuels, low-sulfur diesel and other measures to improve the environment. The American Petroleum Institute (API) estimates that industry will spend between $15 and $23 billion by the end of the decade to meet the U.S. Clean Air Act Amendments (CAAA) of 1990, and other legislation. ENSR Consulting and Engineering's capital-spending figure runs to between $70 and 100 billion this decade, including $24 billion to produce reformulated fuels and $10-12 billion to reduce refinery emissions. M.W. Kellogg Co. estimates that refiners may have to spend up to $30 billion this decade to meet the demand for reformulated gasoline. The estimates are wide-ranging because refiners are still studying their options and delaying final decisions as long as they can, to try to ensure they are the best and least-costly decisions. Oxygenated fuels will be required next winter, but federal regulations for reformulated gasoline won't go into effect until 1995, while California's tougher reformulated-fuels law will kick in the following year

Reproducibility of lateral cephalometric landmarks on conventional radiographs and spatial frequency-processed digital images

International Nuclear Information System (INIS)

Shin, Jeong Won; Heo, Min Suk; Lee, Sam Sun; Choi, Hyun Bae; Choi, Soon Chul; Choi, Hang Moon

2002-01-01

Computed radiography (CR) has been used in cephalometric radiography and many studies have been carried out to improve image quality using various digital enhancement and filtering techniques. During CR image acquisition, the frequency rank and type affect to the image quality. The aim of this study was to compare the diagnostic quality of conventional cephalometric radiographs to those of computed radiography. The diagnostic quality of conventional cephalometric radiographs (M0) and their digital image counterparts were compared, and at the same time, six modalities (M1-M6) of spatial frequency-processed digital images were compared by evaluating the reproducibility of 23 cephalometric landmark locations. Reproducibility was defined as an observer's deviation (in mm) from the mean between all observers. In comparison with the conventional cephalometric radiograph (M0), M1 showed statistically significant differences in 8 locations, M2 in 9, M3 12, M4 in 7, M5 in 12, and M6 showed significant differences in 14 of 23 landmark locations (p<0.05). The number of reproducible landmarks that each modality possesses were 7 in M6, 6 in M5, 5 in M3, 4 in M4, 3 in M2, 2 in M1, and 1 location in M0. The image modality that observers selected as having the best image quality was M5.

Distillation modeling for a uranium refining process

International Nuclear Information System (INIS)

Westphal, B.R.

1996-01-01

As part of the spent fuel treatment program at Argonne National Laboratory, a vacuum distillation process is being employed for the recovery of uranium following an electrorefining process. Distillation of a salt electrolyte, containing a eutectic mixture of lithium and potassium chlorides, from uranium is achieved by a simple batch operation and is termed open-quotes cathode processingclose quotes. The incremental distillation of electrolyte salt will be modeled by an equilibrium expression and on a molecular basis since the operation is conducted under moderate vacuum conditions. As processing continues, the two models will be compared and analyzed for correlation with actual operating results. Possible factors that may contribute to aberrations from the models include impurities at the vapor-liquid boundary, distillate reflux, anomalous pressure gradients, and mass transport phenomena at the evaporating surface. Ultimately, the purpose of either process model is to enable the parametric optimization of the process

Refinement of the concept of uncertainty.

Science.gov (United States)

Penrod, J

2001-04-01

To analyse the conceptual maturity of uncertainty; to develop an expanded theoretical definition of uncertainty; to advance the concept using methods of concept refinement; and to analyse congruency with the conceptualization of uncertainty presented in the theory of hope, enduring, and suffering. Uncertainty is of concern in nursing as people experience complex life events surrounding health. In an earlier nursing study that linked the concepts of hope, enduring, and suffering into a single theoretical scheme, a state best described as 'uncertainty' arose. This study was undertaken to explore how this conceptualization fit with the scientific literature on uncertainty and to refine the concept. Initially, a concept analysis using advanced methods described by Morse, Hupcey, Mitcham and colleagues was completed. The concept was determined to be partially mature. A theoretical definition was derived and techniques of concept refinement using the literature as data were applied. The refined concept was found to be congruent with the concept of uncertainty that had emerged in the model of hope, enduring and suffering. Further investigation is needed to explore the extent of probabilistic reasoning and the effects of confidence and control on feelings of uncertainty and certainty.

Refinement Checking on Parametric Modal Transition Systems

DEFF Research Database (Denmark)

Benes, Nikola; Kretínsky, Jan; Larsen, Kim Guldstrand

2015-01-01

Modal transition systems (MTS) is a well-studied specification formalism of reactive systems supporting a step-wise refinement methodology. Despite its many advantages, the formalism as well as its currently known extensions are incapable of expressing some practically needed aspects in the refin...

Usability Testing as a Method to Refine a Health Sciences Library Website.

Science.gov (United States)

Denton, Andrea H; Moody, David A; Bennett, Jason C

2016-01-01

User testing, a method of assessing website usability, can be a cost-effective and easily administered process to collect information about a website's effectiveness. A user experience (UX) team at an academic health sciences library has employed user testing for over three years to help refine the library's home page. Test methodology used in-person testers using the "think aloud" method to complete tasks on the home page. Review of test results revealed problem areas of the design and redesign; further testing was effective in refining the page. User testing has proved to be a valuable method to engage users and provide feedback to continually improve the library's home page.

Framework for understanding LENR processes, using conventional condensed matter physics

International Nuclear Information System (INIS)

Chubb, Scott R.

2006-01-01

Conventional condensed matter physics provides a unifying framework for understanding low-energy nuclear reactions (LENRs) in solids. In the paper, standard many-body physics techniques are used to illustrate this fact. Specifically, the paper shows that formally the theories by Schwinger, Hagelstein, and Chubb and Chubb (C and C), all can be related to a common set of equations, associated with reaction rate and energy transfer, through a standard many-body physics procedure (R-matrix theory). In each case, particular forms of coherence are used that, implicitly provide a mechanism for understanding how LENRs can proceed without. the emission of high-energy particles. In addition, additional ideas, associated with Conventional Condensed Matter physics, are used to extend the earlier ion band state (IBS) model by C and C. The general model clarifies the origin of coherent. processes that initiate LENRs, through the onset of ion conduction that can occur through ionic fluctuations in nano-scale crystals. In the case of PdD x , these fluctuations begin to occur as x → 1 in sub-lattice structures with characteristic dimensions of 60 nm. The resulting LENRs are triggered by the polarization between injected d's and electrons (immediately above the Fermi energy) that takes place in finite-size PdD crystals. During the prolonged charging of PdD x the applied, external electric field induces these fluctuations through a form of Zener tunneling that mimics the kind of tunneling, predicted by Zener, that is responsible for possible conduction (referred to as Zener-electric breakdown) in insulators. But because the fluctuations are ionic and they occur in PdD, nano-scale structures, a more appropriate characterization is Zener-ionic breakdown in nano-crystalline PdD. Using the underlying dynamics, it is possible to relate triggering times that are required for the initiation of the effect, to crystal size and externally applied fields. (authors)

Japan's refiner/marketers headed for major shakeout

International Nuclear Information System (INIS)

Anon.

1996-01-01

Japan's downstream oil industry is in a state of crisis and headed for a major shakeout. The major catalyst for this was a dramatic deregulation step during April 1996 that allowed refined petroleum product imports by non-refiners. The move, together with a sharp drop in refining margins, falling retail gasoline prices, and a service station sector on the brink of collapse, are all leading to massive changes in the way the country's refiners and marketers do business. This paper reviews the collapse of corporate profits during this period of deregulation; the development of a new price system geared toward bringing the prices of gasoline, fuel oil, and kerosene into line with each other to offset the fall in gasoline prices; and industry restructuring including mergers, acquisitions, and marketing consolidation. The paper then makes predictions on the outcome of these changes on the Japanese oil industry

An enriched finite element model with q-refinement for radiative boundary layers in glass cooling

Energy Technology Data Exchange (ETDEWEB)

Mohamed, M. Shadi [Institute for Infrastructure and Environment, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom); Seaid, Mohammed; Trevelyan, Jon [School of Engineering and Computing Sciences, University of Durham, South Road, Durham DH1 3LE (United Kingdom); Laghrouche, Omar [Institute for Infrastructure and Environment, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom)

2014-02-01

Radiative cooling in glass manufacturing is simulated using the partition of unity finite element method. The governing equations consist of a semi-linear transient heat equation for the temperature field and a stationary simplified P{sub 1} approximation for the radiation in non-grey semitransparent media. To integrate the coupled equations in time we consider a linearly implicit scheme in the finite element framework. A class of hyperbolic enrichment functions is proposed to resolve boundary layers near the enclosure walls. Using an industrial electromagnetic spectrum, the proposed method shows an immense reduction in the number of degrees of freedom required to achieve a certain accuracy compared to the conventional h-version finite element method. Furthermore the method shows a stable behaviour in treating the boundary layers which is shown by studying the solution close to the domain boundaries. The time integration choice is essential to implement a q-refinement procedure introduced in the current study. The enrichment is refined with respect to the steepness of the solution gradient near the domain boundary in the first few time steps and is shown to lead to a further significant reduction on top of what is already achieved with the enrichment. The performance of the proposed method is analysed for glass annealing in two enclosures where the simplified P{sub 1} approximation solution with the partition of unity method, the conventional finite element method and the finite difference method are compared to each other and to the full radiative heat transfer as well as the canonical Rosseland model.

Effect of processing on phenolic composition of dough and bread fractions made from refined and whole wheat flour of three wheat varieties.

Science.gov (United States)

Lu, Yingjian; Luthria, Devanand; Fuerst, E Patrick; Kiszonas, Alecia M; Yu, Liangli; Morris, Craig F

2014-10-29

This study investigated the effect of breadmaking on the assay of phenolic acids from flour, dough, and bread fractions of three whole and refined wheat varieties. Comparison of the efficacy of two commonly used methods for hydrolysis and extraction of phenoilc acids showed that yields of total phenolic acids (TPA) were 5-17% higher among all varieties and flour types when samples were directly hydrolyzed in the presence of ascorbate and EDTA as compared to the method separating free, soluble conjugates and bound, insoluble phenolic acids. Ferulic acid (FA) was the predominant phenolic acid, accounting for means of 59 and 81% of TPA among all refined and whole wheat fractions, respectively. All phenolic acids measured were more abundant in whole wheat than in refined samples. Results indicated that the total quantified phenolic acids did not change significantly when breads were prepared from refined and whole wheat flour. Thus, the potential phytochemical health benefits of total phenolic acids appear to be preserved during bread baking.

Improved cracking characteristics of bitumen through advanced froth treatment process

Energy Technology Data Exchange (ETDEWEB)

Ng, S.H. [National Centre for Upgrading Technology, Devon, AB (Canada); Dabros, T. [Natural Resources Canada, Devon, AB (Canada). CANMET Advanced Separation Technologies Laboratory; Humphries, A. [Albemarle Catalysts Co., Houston, TX (United States)

2006-07-01

Fluid catalytic cracking (FCC) is the dominant refinery conversion process for producing transportation fuels. Feed to the FCC unit is heavy gas oil (HGO). Its quality depends on the crude used and the processes involved. Bitumen-derived crude (BDC), including synthetic crude oil (SCO) is less superior to produce FCC feed than stocks from conventional sources. As a result, North American refiners have limited the use of BDC in their conventional FCC-based operations. This paper examined the improved cracking characteristics of bitumen through an advanced froth treatment process. This involved processing of the bitumen with paraffinic solvent in froth treatment with removal of some asphaltenes, CCR precursors, and metals. The paper discussed the experimental and subsequent results and discussion, including cracking characteristics; product quality; synergetic effect; and economic benefits. It was concluded that the poisoning effect by some deleterious components such as nitrogen compounds in feeds on the catalyst could be reduced or compensated for by higher C/O ratios (more catalyst per unit weight of feed). In addition, as conversion increased, sulfur in gasoline decreased slightly and linearly with more or less the same magnitude for the two bitumens. 5 refs., 1 tab., 3 figs.

Olefins from conventional and heavy feedstocks: Energy use in steam cracking and alternative processes

International Nuclear Information System (INIS)

Ren Tao; Patel, Martin; Blok, Kornelis

2006-01-01

Steam cracking for the production of light olefins, such as ethylene and propylene, is the single most energy-consuming process in the chemical industry. This paper reviews conventional steam cracking and innovative olefin technologies in terms of energy efficiency. It is found that the pyrolysis section of a naphtha steam cracker alone consumes approximately 65% of the total process energy and approximately 75% of the total exergy loss. A family portrait of olefin technologies by feedstocks is drawn to search for alternatives. An overview of state-of-the-art naphtha cracking technologies shows that approximately 20% savings on the current average process energy use are possible. Advanced naphtha cracking technologies in the pyrolysis section, such as advanced coil and furnace materials, could together lead to up to approximately 20% savings on the process energy use by state-of-the-art technologies. Improvements in the compression and separation sections could together lead to up to approximately 15% savings. Alternative processes, i.e. catalytic olefin technologies, can save up to approximately 20%

Management of wastes from the refining and conversion of uranium ore concentrate to uranium hexafluoride

International Nuclear Information System (INIS)

1981-01-01

This report is the outcome of an IAEA Advisory Group Meeting on ''Waste Management Aspects in Relation to the Refining of Uranium Ore Concentrates and their Conversion to Uranium Hexafluoride'', which was held in Vienna from 17 to 21 December 1979. The report summarizes the main topics discussed at the meeting and gives an overview of uranium refining processes, being used in nuclear industry. The meeting was organized by the International Atomic Energy Agency, Radioactive Waste Management Section

The refinement of ipsilateral eye retinotopic maps is increased by removing the dominant contralateral eye in adult mice.

Directory of Open Access Journals (Sweden)

Spencer L Smith

2010-03-01

Full Text Available Shortly after eye opening, initially disorganized visual cortex circuitry is rapidly refined to form smooth retinotopic maps. This process asymptotes long before adulthood, but it is unknown whether further refinement is possible. Prior work from our lab has shown that the retinotopic map of the non-dominant ipsilateral eye develops faster when the dominant contralateral eye is removed. We examined whether input from the contralateral eye might also limit the ultimate refinement of the ipsilateral eye retinotopic map in adults. In addition, we examined whether the increased refinement involved the recruitment of adjacent cortical area.By surgically implanting a chronic optical window over visual cortex in mice, we repeatedly measured the degree of retinotopic map refinement using quantitative intrinsic signal optical imaging over four weeks. We removed the contralateral eye and observed that the retinotopic map for the ipsilateral eye was further refined and the maximum magnitude of response increased. However, these changes were not accompanied by an increase in the area of responsive cortex.Since the retinotopic map was functionally refined to a greater degree without taking over adjacent cortical area, we conclude that input from the contralateral eye limits the normal refinement of visual cortical circuitry in mice. These findings suggest that the refinement capacity of cortical circuitry is normally saturated.

A Macdonald refined topological vertex

Science.gov (United States)

Foda, Omar; Wu, Jian-Feng

2017-07-01

We consider the refined topological vertex of Iqbal et al (2009 J. High Energy Phys. JHEP10(2009)069), as a function of two parameters ≤ft\\lgroup x, y \\right\\rgroup , and deform it by introducing the Macdonald parameters ≤ft\\lgroup q, t \\right\\rgroup , as in the work of Vuletić on plane partitions (Vuletić M 2009 Trans. Am. Math. Soc. 361 2789-804), to obtain ‘a Macdonald refined topological vertex’. In the limit q → t , we recover the refined topological vertex of Iqbal et al and in the limit x → y , we obtain a qt-deformation of the original topological vertex of Aganagic et al (2005 Commun. Math. Phys. 25 425-78). Copies of the vertex can be glued to obtain qt-deformed 5D instanton partition functions that have well-defined 4D limits and, for generic values of ≤ft\\lgroup q, t\\right\\rgroup , contain infinite-towers of poles for every pole present in the limit q → t .

Grain refinement of AZ31 magnesium alloy by electromagnetic ...

Indian Academy of Sciences (India)

Low-frequency electromagnetic field; AZ31 magnesium alloy; Al4C3; grain refinement. Abstract. The effects of electromagnetic stirring and Al4C3 grain refiner on the grain refinement of semicontinuously cast AZ31 magnesium alloy were discussed in this investigation. The results indicate that electromagnetic stirring has an ...

A refined index of model performance: a rejoinder

Science.gov (United States)

Legates, David R.; McCabe, Gregory J.

2013-01-01

Willmott et al. [Willmott CJ, Robeson SM, Matsuura K. 2012. A refined index of model performance. International Journal of Climatology, forthcoming. DOI:10.1002/joc.2419.] recently suggest a refined index of model performance (dr) that they purport to be superior to other methods. Their refined index ranges from − 1.0 to 1.0 to resemble a correlation coefficient, but it is merely a linear rescaling of our modified coefficient of efficiency (E1) over the positive portion of the domain of dr. We disagree with Willmott et al. (2012) that dr provides a better interpretation; rather, E1 is more easily interpreted such that a value of E1 = 1.0 indicates a perfect model (no errors) while E1 = 0.0 indicates a model that is no better than the baseline comparison (usually the observed mean). Negative values of E1 (and, for that matter, dr McCabe [Legates DR, McCabe GJ. 1999. Evaluating the use of “goodness-of-fit” measures in hydrologic and hydroclimatic model validation. Water Resources Research 35(1): 233-241.] and Schaefli and Gupta [Schaefli B, Gupta HV. 2007. Do Nash values have value? Hydrological Processes 21: 2075-2080. DOI: 10.1002/hyp.6825.]. This important discussion focuses on the appropriate baseline comparison to use, and why the observed mean often may be an inadequate choice for model evaluation and development. 

PM-10 emissions and power of a Diesel engine fueled with crude and refined Biodiesel from salmon oil

Energy Technology Data Exchange (ETDEWEB)

J.F. Reyes; M.A. Sepulveda [University of Concepcion (Chile). Department of Mechanization and Energy, Faculty of Agricultural Engineering

2006-09-15

Power response and level of particulate emissions were assessed for blends of Diesel-crude Biodiesel and Diesel-refined Biodiesel. Crude Biodiesel and refined Biodiesel or methyl ester, were made from salmon oil with high content of free fatty acids, throughout a process of acid esterification followed by alkaline transesterification. Blends of Diesel-crude Biodiesel and Diesel-refined Biodiesel were tested in a diesel engine to measure simultaneously the dynamometric response and the particulate material (PM-10) emission performance. The results indicate a maximum power loss of about 3.5% and also near 50% of PM-10 reduction with respect to diesel when a 100% of refined Biodiesel is used. For blends with less content of either crude Biodiesel or refined Biodiesel, the observed power losses are lower but at the same time lower reduction in PM-10 emissions are attained. 21 refs., 4 figs., 2 tabs.

Refinement of RAIM via Implementation of Implicit Euler Method

Energy Technology Data Exchange (ETDEWEB)

Lee, Yoonhee; Kim, Han-Chul [Korea Institute of Nuclear and Safety, Daejeon (Korea, Republic of)

2016-10-15

The first approach is a mechanistic approach which is used in LIRIC in which more than 200 reactions are modeled in detail. This approach enables to perform the detailed analysis. However, it requires huge computation burden. The other approach is a simplified model approach which is used in the IMOD, ASTEC/IODE, and etc. Recently, KINS has developed RAIM (Radio-Active Iodine chemistry Model) based on the simplified model approach. Since the numerical analysis module in RAIM is based on the explicit Euler method, there are major issues on the stability of the module. Therefore, implementation of a stable numerical method becomes essential. In this study, RAIM is refined via implementation of implicit Euler method in which the Newton method is used to find the solutions at each time step. The refined RAIM is tested by comparing to RAIM based on the explicit Euler method. In this paper, RAIM was refined by implementing the implicit Euler method. At each time step of the method in the refined RAIM, the reaction kinetics equations are solved by the Newton method in which elements of the Jacobian matrix are expressed analytically. With the results of OECD-BIP P10T2 test, the refined RAIM was compared to RAIM with the explicit Euler method. The refined RAIM shows better agreement with the experimental data than those from the explicit Euler method. For the rapid change of pH during the experiment, the refined RAIM gives more realistic changes in the concentrations of chemical species than those from the explicit Euler method. In addition, in terms of computing time, the refined RAIM shows comparable computing time to that with explicit Euler method. These comparisons are attributed to ⁓10 times larger time step size used in the implicit Euler method, even though computation burden at each time step in the refined RAIM is much higher than that of the explicit Euler method. Compared to the experimental data, the refined RAIM still shows discrepancy, which are attributed

Refinement of RAIM via Implementation of Implicit Euler Method

International Nuclear Information System (INIS)

Lee, Yoonhee; Kim, Han-Chul

2016-01-01

The first approach is a mechanistic approach which is used in LIRIC in which more than 200 reactions are modeled in detail. This approach enables to perform the detailed analysis. However, it requires huge computation burden. The other approach is a simplified model approach which is used in the IMOD, ASTEC/IODE, and etc. Recently, KINS has developed RAIM (Radio-Active Iodine chemistry Model) based on the simplified model approach. Since the numerical analysis module in RAIM is based on the explicit Euler method, there are major issues on the stability of the module. Therefore, implementation of a stable numerical method becomes essential. In this study, RAIM is refined via implementation of implicit Euler method in which the Newton method is used to find the solutions at each time step. The refined RAIM is tested by comparing to RAIM based on the explicit Euler method. In this paper, RAIM was refined by implementing the implicit Euler method. At each time step of the method in the refined RAIM, the reaction kinetics equations are solved by the Newton method in which elements of the Jacobian matrix are expressed analytically. With the results of OECD-BIP P10T2 test, the refined RAIM was compared to RAIM with the explicit Euler method. The refined RAIM shows better agreement with the experimental data than those from the explicit Euler method. For the rapid change of pH during the experiment, the refined RAIM gives more realistic changes in the concentrations of chemical species than those from the explicit Euler method. In addition, in terms of computing time, the refined RAIM shows comparable computing time to that with explicit Euler method. These comparisons are attributed to ⁓10 times larger time step size used in the implicit Euler method, even though computation burden at each time step in the refined RAIM is much higher than that of the explicit Euler method. Compared to the experimental data, the refined RAIM still shows discrepancy, which are attributed

The European refining and distribution industry at the 2010 vista

International Nuclear Information System (INIS)

Lacour, J.J.; Tessmer, G.; Ward, I.

1998-01-01

Oil company chairmen belonging to the AFTP, DGMK and IP associations met together to debate about the future of the European refining industry. The following topics were discussed: is it the end of the refining crisis? Which uncertainties will have to be met? What is the situation of petroleum products supply and demand? What are the consumers' expectations? How to face the environmental constraints? Which future for the refining activities in Europe? Seven round-tables took place with the following themes: the factors of uncertainty in the future of refining activities, the petroleum products supply and demand (automotive fuels, fuel oils, lubricants), the refining activities and the supply of consumers (service stations and supermarkets), the situation of the European petroleum policy, the European refining industry and the public regulations (development of more efficient environmental approaches), the impact of environmental constraints and the technical solutions, and the future of the refining industry. (J.S.)

Zone refining high-purity germanium

International Nuclear Information System (INIS)

Hubbard, G.S.; Haller, E.E.; Hansen, W.L.

1977-10-01

The effects of various parameters on germanium purification by zone refining have been examined. These parameters include the germanium container and container coatings, ambient gas and other operating conditions. Four methods of refining are presented which reproducibly yield 3.5 kg germanium ingots from which high purity (vertical barN/sub A/ - N/sub D/vertical bar less than or equal to2 x 10 10 cm -3 ) single crystals can be grown. A qualitative model involving binary and ternary complexes of Si, O, B, and Al is shown to account for the behavior of impurities at these low concentrations

The effect of grain refinement and silicon content on grain formation in hypoeutectic Al-Si alloys

Energy Technology Data Exchange (ETDEWEB)

Lee, Y.C.; Dahle, A.K.; StJohn, D.H.; Hutt, J.E.C. [Queensland Univ., Brisbane (Australia). Dept. of Mining, Minerals and Mater. Eng.

1999-01-15

The effect of increasing the amount of added grain refiner on grain size and morphology has been investigated for a range of hypoeutectic Al-Si alloys. The results show a transition in grain size at a silicon concentration of about 3 wt% in unrefined alloys; the grain size decreasing with silicon content before the transition, and increasing beyond the transition point. A change in morphology also occurs with increased silicon content. The addition of grain refiner leads to greater refinement for silicon contents below the transition point than for those contents above the transition point, while the transition point seems to remain unchanged. The slope of the grain size versus silicon content curve after the transition seems to be unaffected by the degree of grain refinement. The results are related to the competitive processes of nucleation and constitutional effects during growth and their impact on nucleation kinetics. (orig.) 13 refs.

Adaptive mesh refinement for shocks and material interfaces

Energy Technology Data Exchange (ETDEWEB)

Dai, William Wenlong [Los Alamos National Laboratory

2010-01-01

There are three kinds of adaptive mesh refinement (AMR) in structured meshes. Block-based AMR sometimes over refines meshes. Cell-based AMR treats cells cell by cell and thus loses the advantage of the nature of structured meshes. Patch-based AMR is intended to combine advantages of block- and cell-based AMR, i.e., the nature of structured meshes and sharp regions of refinement. But, patch-based AMR has its own difficulties. For example, patch-based AMR typically cannot preserve symmetries of physics problems. In this paper, we will present an approach for a patch-based AMR for hydrodynamics simulations. The approach consists of clustering, symmetry preserving, mesh continuity, flux correction, communications, management of patches, and load balance. The special features of this patch-based AMR include symmetry preserving, efficiency of refinement across shock fronts and material interfaces, special implementation of flux correction, and patch management in parallel computing environments. To demonstrate the capability of the AMR framework, we will show both two- and three-dimensional hydrodynamics simulations with many levels of refinement.

Study on the Impact Characteristics of Coherent Supersonic Jet and Conventional Supersonic Jet in EAF Steelmaking Process

Science.gov (United States)

Wei, Guangsheng; Zhu, Rong; Cheng, Ting; Dong, Kai; Yang, Lingzhi; Wu, Xuetao

2018-02-01

Supersonic oxygen-supplying technologies, including the coherent supersonic jet and the conventional supersonic jet, are now widely applied in electric arc furnace steelmaking processes to increase the bath stirring, reaction rates, and energy efficiency. However, there has been limited research on the impact characteristics of the two supersonic jets. In the present study, by integrating theoretical modeling and numerical simulations, a hybrid model was developed and modified to calculate the penetration depth and impact zone volume of the coherent and conventional supersonic jets. The computational fluid dynamics results were validated against water model experiments. The results show that the lance height has significant influence on the jet penetration depth and jet impact zone volume. The penetration depth decreases with increasing lance height, whereas the jet impact zone volume initially increases and then decreases with increasing lance height. In addition, the penetration depth and impact zone volume of the coherent supersonic jet are larger than those of the conventional supersonic jet at the same lance height, which illustrates the advantages of the coherent supersonic jet in delivering great amounts of oxygen to liquid melt with a better stirring effect compared to the conventional supersonic jet. A newly defined parameter, the k value, reflects the velocity attenuation and the potential core length of the main supersonic jet. Finally, a hybrid model and its modifications can well predict the penetration depth and impact zone volume of the coherent and conventional supersonic jets.

Energy conservation potential in China’s petroleum refining industry: Evidence and policy implications

International Nuclear Information System (INIS)

Lin, Boqiang; Xie, Xuan

2015-01-01

Highlights: • A long-term equilibrium relationship of energy demand in China’s petroleum refining industry is established. • The sectoral energy conservation potential is evaluated by using scenarios analysis. • Energy prices, enterprise scale, R and D investment and ownership structure affect electricity intensity. • Future policy for energy conservation in China’s petroleum refining industry is suggested. - Abstract: China is currently the second largest petroleum refining country in the world due to rapid growth in recent years. Because the petroleum refining industry is energy-intensive, the rapid growth in petroleum refining and development caused massive energy consumption. China’s urbanization process will guarantee sustained growth of the industry for a long time. Therefore, it is necessary to study the energy conservation potential of the petroleum industry. This paper estimates the energy conservation potential of the industry by applying a cointegration model to investigate the long-run equilibrium relationship between energy consumption and some factors such as energy price, enterprise scale, R and D investment and ownership structure. The results show that R and D investment has the greatest reduction impact on energy intensity, and the growth of market participants (i.e. the decline of the share of state-owned companies) can improve energy efficiency of this industry. Under the advanced energy-saving scenario, the accumulated energy conservation potential will reach 230.18 million tons of coal equivalent (tce). Finally, we provide some targeted policy recommendations for industrial energy conservation

Review of Grain Refinement of Cast Metals Through Inoculation: Theories and Developments

Science.gov (United States)

Liu, Zhilin

2017-10-01

The inoculation method of grain refinement is widely used in research and industry. Because of its commercial and engineering importance, extensive research on the mechanisms/theories of grain refinement and development of effective grain refiners for diverse cast metals/alloys has been conducted. In 1999, Easton and St. John reviewed the mechanisms of grain refinement of cast Al alloys. Since then, grain refinement in alloys of Al, Mg, Fe, Ti, Cu, and Zn has evolved a lot. However, there is still no full consensus on the mechanisms/theories of grain refinement. Moreover, some new grain refiners developed based on the theories do not ensure efficient grain refinement. Thus, the factors that contribute to grain refinement are still not fully understood. Clarification of the prerequisite issues that occur in grain refinement is required using recent theories. This review covers multiple metals/alloys and developments in grain refinement from the last twenty years. The characteristics of effective grain refiners are considered from four perspectives: effective particle/matrix wetting configuration, sufficiently powerful segregating elements, preferential crystallographic matching, and geometrical features of effective nucleants. Then, recent mechanisms/theories on the grain refinement of cast metals/alloys are reviewed, including the peritectic-related, hypernucleation, inert nucleant, and constitutional supercooling-driven theories. Further, developments of deterministic and probabilistic modeling and nucleation crystallography in the grain refinement of cast metals are reviewed. Finally, the latest progress in the grain refinement of cast Zn and its alloys is described, and future work on grain refinement is summarized.

Proceedings of the DGMK-conference 'Chances for innovative processes at the interface between refining and petrochemistry'. Authors' manuscripts

Energy Technology Data Exchange (ETDEWEB)

Emig, G; Gallei, E; Luecke, B; Weitkamp, J [eds.

2002-07-01

The latest developments in the field of petrochemical refining are reviewed in 37 papers. Main topics are catalysts developments for various chemical reactions, ionic liquids, zeolite and metal catalysts. (uke)

Removal of antibiotics from surface and distilled water in conventional water treatment processes

Science.gov (United States)

Adams, C.; Wang, Y.; Loftin, K.; Meyer, M.

2002-01-01

Conventional drinking water treatment processes were evaluated under typical water treatment plant conditions to determine their effectiveness in the removal of seven common antibiotics: carbadox, sulfachlorpyridazine, sulfadimethoxine, sulfamerazine, sulfamethazine, sulfathiazole, and trimethoprim. Experiments were conducted using synthetic solutions prepared by spiking both distilled/ deionized water and Missouri River water with the studied compounds. Sorption on Calgon WPH powdered activated carbon, reverse osmosis, and oxidation with chlorine and ozone under typical plant conditions were all shown to be effective in removing the studied antibiotics. Conversely, coagulation/flocculation/sedimentation with alum and iron salts, excess lime/soda ash softening, ultraviolet irradiation at disinfection dosages, and ion exchange were all relatively ineffective methods of antibiotic removal. This study shows that the studied antibiotics could be effectively removed using processes already in use many water treatment plants. Additional work is needed on by-product formation and the removal of other classes of antibiotics.

Total antioxidant content of alternatives to refined sugar.

Science.gov (United States)

Phillips, Katherine M; Carlsen, Monica H; Blomhoff, Rune

2009-01-01

Oxidative damage is implicated in the etiology of cancer, cardiovascular disease, and other degenerative disorders. Recent nutritional research has focused on the antioxidant potential of foods, while current dietary recommendations are to increase the intake of antioxidant-rich foods rather than supplement specific nutrients. Many alternatives to refined sugar are available, including raw cane sugar, plant saps/syrups (eg, maple syrup, agave nectar), molasses, honey, and fruit sugars (eg, date sugar). Unrefined sweeteners were hypothesized to contain higher levels of antioxidants, similar to the contrast between whole and refined grain products. To compare the total antioxidant content of natural sweeteners as alternatives to refined sugar. The ferric-reducing ability of plasma (FRAP) assay was used to estimate total antioxidant capacity. Major brands of 12 types of sweeteners as well as refined white sugar and corn syrup were sampled from retail outlets in the United States. Substantial differences in total antioxidant content of different sweeteners were found. Refined sugar, corn syrup, and agave nectar contained minimal antioxidant activity (sugar had a higher FRAP (0.1 mmol/100 g). Dark and blackstrap molasses had the highest FRAP (4.6 to 4.9 mmol/100 g), while maple syrup, brown sugar, and honey showed intermediate antioxidant capacity (0.2 to 0.7 mmol FRAP/100 g). Based on an average intake of 130 g/day refined sugars and the antioxidant activity measured in typical diets, substituting alternative sweeteners could increase antioxidant intake an average of 2.6 mmol/day, similar to the amount found in a serving of berries or nuts. Many readily available alternatives to refined sugar offer the potential benefit of antioxidant activity.

Solvent refined coal studies: effects and characterization of treated solvent refined coal effluent. Progress report, FY 1977

Energy Technology Data Exchange (ETDEWEB)

Becker, C.D.; Woodfield, W.G.; Strand, J.A.

1978-07-01

The Freshwater Sciences Section of PNL has initiated biologically oriented studies at the P and M solvent refined coal (SRC) pilot plant on the Fort Lewis Reservation in western Washington. Essentially, the study objectives are to identify residual components in the treated SRC process and assess potential for adverse impact on water quality and aquatic biota. Since inception of research in mid-1976, six static toxicity tests with treated SRC process effluent have been conducted. Toxic components, not yet specifically identified, sometimes occur in the effluent. It is believed these components involve organic hydrocarbons of the phenol and cresol groups. Analyses have been obtained on inorganic and organic constituents in partially-treated and treated process effluent. Concentrations of inorganics identified in the effluent did not differ greatly from their concentrations in Lake Sequalitchew or SRC plant tap water, but the low concentrations may be due primarily to dilution with freshwater before discharge. Organics identified in the effluent are similar to those found in samples contaminated with petroleum, and involve many complex hydrocarbons.

Precipitation behavior and grain refinement of burnishing Al-Zn-Mg alloy

Directory of Open Access Journals (Sweden)

Ce Pang

2018-02-01

Full Text Available Burnishing is a unique strengthening approach to improve the strength of surface layer and remains the ductility of the interior of metallic materials. In this work, burnishing treatment was employed to improve the surface microstructure of naturally aged Al-Zn-Mg alloys after solid solution. Transmission electron microscopy, high-resolution transmission electron microscopy, X-ray diffraction and nano-indentation were used to characterize the effects of the burnishing on the microstructures of surface layer and Guinier-Preston (GP zones. It was indicated that GP zones uniformly distributed and dispersed in the matrix before burnishing, and the amount of GP zones decreased dramatically after burnishing processing. Additionally, the grains in the surficial layer were refined into nano-crystals with an average grain size of 78 nm. Burnishing treatment not only led to formation of large number of dislocation substructures in the sub-surface and near-matrix surface, but also promoted the precipitation of metastable η' phase at grain boundaries. The synergistic effects of the grain refinement, dislocation multiplication and the precipitation of η' phase strengthen the burnished layer of Al-Zn-Mg alloy. Keywords: Al-Zn-Mg alloy, Burnishing, Nano-crystal, Precipitation, Grain refinement

Investment in exploration-production and refining 2015

International Nuclear Information System (INIS)

Maisonnier, G.; Hureau, G.; Serbutoviez, S.; Silva, C.

2016-01-01

IFPEN analyses in this study the 2015 evolution of global investment in the field of exploration-production and refining: - Changes in oil and gas prices; - Investment in Exploration/Production: the end of an upward cycle; - Drilling and the global drilling market, upstream activities and markets; - 2015, a breath of fresh air for refining

Thermal Adsorption Processing Of Hydrocarbon Residues

Directory of Open Access Journals (Sweden)

Sudad H. Al.

2017-04-01

Full Text Available The raw materials of secondary catalytic processes must be pre-refined. Among these refining processes are the deasphalting and demetallization including their thermo adsorption or thermo-contact adsorption variety. In oil processing four main processes of thermo-adsorption refining of hydrocarbon residues are used ART Asphalt Residual Treating - residues deasphaltizing 3D Discriminatory Destructive Distillation developed in the US ACT Adsorption-Contact Treatment and ETCC Express Thermo-Contact Cracking developed in Russia. ART and ACT are processes with absorbers of lift type reactor while 3D and ETCC processes are with an adsorbing reactor having ultra-short contact time of the raw material with the adsorbent. In all these processes refining of hydrocarbon residues is achieved by partial Thermo-destructive transformations of hydrocarbons and hetero-atomic compounds with simultaneous adsorption of the formed on the surface of the adsorbents resins asphaltene and carboids as well as metal- sulphur - and nitro-organic compounds. Demetallized and deasphalted light and heavy gas oils or their mixtures are a quality raw material for secondary deepening refining processes catalytic and hydrogenation cracking etc. since they are characterized by low coking ability and low content of organometallic compounds that lead to irreversible deactivation of the catalysts of these deepening processes.

Hirshfeld atom refinement.

Science.gov (United States)

Capelli, Silvia C; Bürgi, Hans-Beat; Dittrich, Birger; Grabowsky, Simon; Jayatilaka, Dylan

2014-09-01

Hirshfeld atom refinement (HAR) is a method which determines structural parameters from single-crystal X-ray diffraction data by using an aspherical atom partitioning of tailor-made ab initio quantum mechanical molecular electron densities without any further approximation. Here the original HAR method is extended by implementing an iterative procedure of successive cycles of electron density calculations, Hirshfeld atom scattering factor calculations and structural least-squares refinements, repeated until convergence. The importance of this iterative procedure is illustrated via the example of crystalline ammonia. The new HAR method is then applied to X-ray diffraction data of the dipeptide Gly-l-Ala measured at 12, 50, 100, 150, 220 and 295 K, using Hartree-Fock and BLYP density functional theory electron densities and three different basis sets. All positions and anisotropic displacement parameters (ADPs) are freely refined without constraints or restraints - even those for hydrogen atoms. The results are systematically compared with those from neutron diffraction experiments at the temperatures 12, 50, 150 and 295 K. Although non-hydrogen-atom ADPs differ by up to three combined standard uncertainties (csu's), all other structural parameters agree within less than 2 csu's. Using our best calculations (BLYP/cc-pVTZ, recommended for organic molecules), the accuracy of determining bond lengths involving hydrogen atoms from HAR is better than 0.009 Å for temperatures of 150 K or below; for hydrogen-atom ADPs it is better than 0.006 Å(2) as judged from the mean absolute X-ray minus neutron differences. These results are among the best ever obtained. Remarkably, the precision of determining bond lengths and ADPs for the hydrogen atoms from the HAR procedure is comparable with that from the neutron measurements - an outcome which is obtained with a routinely achievable resolution of the X-ray data of 0.65 Å.

Pakistan stepping up expansion of refining, transportation sectors

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that Pakistan is taking steps to speed expansion of its refining and oil transportation infrastructure. While the country has made significant progress toward energy self-efficiency by boosting oil and gas production it still must modernize and expand an aging, inadequate refining sector to meet rapidly growing demand for refined products. Pakistan's government has disclosed plans to build two refineries in the country, one at Rawalpindi near a string of recent oil discoveries, the other somewhere in the southern part of the country, likely Karachi. At the same time, efforts are proceeding to upgrade Pakistan's refineries. In addition, Pakistani state companies continue to press joint ventures in refining and marketing with foreign companies and expand downstream ties with neighbors that are key oil and gas exporters

Glycidyl esters in refined palm (Elaeis guineensis) oil and related fractions. Part II: practical recommendations for effective mitigation.

Science.gov (United States)

Craft, Brian D; Nagy, Kornél; Seefelder, Walburga; Dubois, Mathieu; Destaillats, Frédéric

2012-05-01

In a previous work, it was shown that at high temperatures (up to 280°C) glycidyl esters (GE) are formed from diacylglycerols (DAG) via elimination of free fatty acid (FFA). In the present study, the impact of DAG content and temperature on the formation of GE using a model vacuum system mimicking industrial edible oil deodorization is investigated. These deodorization experiments confirmed that the formation of GE from DAG is extensive at temperatures above 230-240°C, and therefore, this value should be considered as an upper limit for refining operations. Furthermore, experimental data suggest that the formation of GE accelerates in particular when the DAG levels in refined oils exceed 3-4% of total lipids. Analysis of the lipid composition of crude palm oil (CPO) samples allowed the estimation that this critical DAG content corresponds to about 1.9-2.5% of FFA, which is the conventional quality marker of CPO. Moreover, high levels (>100ppm) of GE were also found in palm fatty acid distillate samples, which may indicate that the level of GE in fully refined palm oils also depends on the elimination rate of GE into the fatty acid distillate. Copyright © 2011 Elsevier Ltd. All rights reserved.

Identification of key oil refining technologies for China National Petroleum Co. (CNPC)

International Nuclear Information System (INIS)

Liu Haiyan; Yu Jianning; Xu Jian; Fan Yu; Bao Xiaojun

2007-01-01

This paper summarizes the results from the project 'Vision of the Key Petroleum Refining Technologies for China National Petroleum Co. (CNPC) in the Early 21st Century' undertaken by the Department of R and D Administration, CNPC, and its affiliate key laboratory, The Key Laboratory of Catalysis operated by China University of Petroleum, Beijing. The objective of the project was to identify the challenges and opportunities of CNPC's petroleum refining business given increasing economy globalization and stricter environmental regulations. Using the modified Delphi method, four key technologies for CNPC's oil refining industry were identified. They are: integrated fluid catalytic cracking (FCC), hydroprocessing, residue hydrocracking, and high-grade lubricant production. The most significant technology will be the integrated FCC technology that can economically increase the yield of light fractions as well as upgrade transportation fuels. In China, FCC units produce about 80% and 30% commercial gasoline and diesel, respectively. To ensure compliance with future environmental legislation, hydroprocessing technologies, including those related to petroleum product hydrorefining and distillate hydrocracking, should be developed. By combining residue hydrocracking and FCC technologies, poorer quality residua can be processed. Supplying high-grade lube oils is one of the main tasks for CNPC's oil refining industry. Development of hydrodewaxing technologies to manufacture API group II/III base oil is the main direction for CNPC's lubricant production business

Refining design of superconducting magnets synchronous with winding using particle swarm optimization

International Nuclear Information System (INIS)

Du, J.J.; Wu, W.; Mei, E.M.; Yuan, P.; Ma, L.Z.; Dong, Z.W.

2013-01-01

Highlights: ► A method of synchronous optimization design of superconducting magnets is proposed. ► We get a refining design of a main magnet on Lanzhou Penning Trap by the method. ► We expounds the necessity of tracking optimizing of coils for magnets. ► Particle swarm optimization shows effectiveness in magnet optimization. ► The expected homogeneity of the magnet improves considerably. -- Abstract: A methodology of synchronous optimization design of magnets under construction according to original design scheme is put forward in this paper, and it has been successfully used for refining design of a superconducting magnet on Lanzhou Penning Trap (LPT). This paper expounds the necessity of tracking optimization of magnet coil in the process of traditional manufacturing, and optimization design of magnet coils by particle swarm optimization is proposed. Particle swarm optimization is turned out to be an effective design method for magnet optimization. The expected homogeneity of the magnet is improved to 200 ppm from 1150 ppm through the refining optimizing, which provides important guarantee for required homogeneity of the whole magnet

Dynamics of the European refining and petrochemical industry. Strategies, structure and change

International Nuclear Information System (INIS)

Steenbakkers, K.

1997-01-01

The changes in the market position of producers engaged in the oil refining and basic petrochemical industry on the Western European market are the central theme of this book. Analysis of this reshuffling process among these actors is conducted on three levels. First, research is carried out at the level of world regions. In order to understand the reorganization of oil refining and basic petrochemical production in Western Europe, it is necessary to explore the recent aggregate dynamics of these activities on a global scale. Second, the differences in strategic behaviour are exanuned at the level of groups of market participants, namely the major oil companies, the chemical companies, the state-owned companies from both consumer and producer countries, and the independents. Finally, the investment/disinvestment decisions in the Western European oil refining and basic petrochemical industry are investigated at the level of the individual firm. Particular emphasis is placed upon explaining why companies active in the sectors under study have followed different strategies, although they have been confronted with similar adverse market conditions in Western Europe during the last decades. 341 refs

The Analysis of Force Parameters in Drawing Process of High Carbon Steel Wires in Conventional and Hydrodynamic Dies

Directory of Open Access Journals (Sweden)

Suliga M.

2017-12-01

Full Text Available The paper analyzes force parameters in the process of multistage drawing of steel wires in conventional and hydrodynamic dies. The drawing process of the wire rod with a diameter of 5.5 mm for wires with a diameter of 1.70 mm was performed in 12 drafts with the usage of the multistage drawbench Koch KGT with the speed range of 5-25 m/s.

Local Refinement of the Super Element Model of Oil Reservoir

Directory of Open Access Journals (Sweden)

A.B. Mazo

2017-12-01

Full Text Available In this paper, we propose a two-stage method for petroleum reservoir simulation. The method uses two models with different degrees of detailing to describe hydrodynamic processes of different space-time scales. At the first stage, the global dynamics of the energy state of the deposit and reserves is modeled (characteristic scale of such changes is km / year. The two-phase flow equations in the model of global dynamics operate with smooth averaged pressure and saturation fields, and they are solved numerically on a large computational grid of super-elements with a characteristic cell size of 200-500 m. The tensor coefficients of the super-element model are calculated using special procedures of upscaling of absolute and relative phase permeabilities. At the second stage, a local refinement of the super-element model is constructed for calculating small-scale processes (with a scale of m / day, which take place, for example, during various geological and technical measures aimed at increasing the oil recovery of a reservoir. Then we solve the two-phase flow problem in the selected area of the measure exposure on a detailed three-dimensional grid, which resolves the geological structure of the reservoir, and with a time step sufficient for describing fast-flowing processes. The initial and boundary conditions of the local problem are formulated on the basis of the super-element solution. This approach allows us to reduce the computational costs in order to solve the problems of designing and monitoring the oil reservoir. To demonstrate the proposed approach, we give an example of the two-stage modeling of the development of a layered reservoir with a local refinement of the model during the isolation of a water-saturated high-permeability interlayer. We show a good compliance between the locally refined solution of the super-element model in the area of measure exposure and the results of numerical modeling of the whole history of reservoir

Global climate convention

International Nuclear Information System (INIS)

Simonis, U.E.

1991-01-01

The effort of negotiate a global convention on climate change is one of mankind's great endeavours - and a challenge to economists and development planners. The inherent linkages between climate and the habitability of the earth are increasingly well recognized, and a convention could help to ensure that conserving the environment and developing the economy in the future must go hand in hand. Due to growing environmental concern the United Nations General Assembly has set into motion an international negotiating process for a framework convention on climate change. One the major tasks in these negotiations is how to share the duties in reducing climate relevant gases, particularly carbon dioxide (CO 2 ), between the industrial and the developing countries. The results and proposals could be among the most far-reaching ever for socio-economic development, indeed for global security and survival itself. While the negotiations will be about climate and protection of the atmosphere, they will be on fundamental global changes in energy policies, forestry, transport, technology, and on development pathways with low greenhouse gas emissions. Some of these aspects of a climate convention, particularly the distributional options and consequences for the North-South relations, are addressed in this chapter. (orig.)

Nonlinear joint dynamics between prices of crude oil and refined products

Science.gov (United States)

Zhang, Tao; Ma, Guofeng; Liu, Guangsheng

2015-02-01

In this paper, we investigate the relationships between crude oil and refined product prices. We find that nonlinear correlations are stronger in the long-term than in the short-term. Crude oil and product prices are cointegrated and financial crisis in 2007-2008 caused a structural break of the cointegrating relationship. Moreover, different from the findings in most studies, we reveal that the relationships are almost symmetric based on a threshold error correction model. The so-called 'asymmetric relationships' are caused by some outliers and financial crisis. Most of the time, crude oil prices play the major role in the adjustment process of the long-term equilibrium. However, refined product prices dominated crude oil prices during the period of financial crisis. Important policy and risk management implications can be learned from the empirical findings.

Conventions and workflows for using Situs

International Nuclear Information System (INIS)

Wriggers, Willy

2012-01-01

Recent developments of the Situs software suite for multi-scale modeling are reviewed. Typical workflows and conventions encountered during processing of biophysical data from electron microscopy, tomography or small-angle X-ray scattering are described. Situs is a modular program package for the multi-scale modeling of atomic resolution structures and low-resolution biophysical data from electron microscopy, tomography or small-angle X-ray scattering. This article provides an overview of recent developments in the Situs package, with an emphasis on workflows and conventions that are important for practical applications. The modular design of the programs facilitates scripting in the bash shell that allows specific programs to be combined in creative ways that go beyond the original intent of the developers. Several scripting-enabled functionalities, such as flexible transformations of data type, the use of symmetry constraints or the creation of two-dimensional projection images, are described. The processing of low-resolution biophysical maps in such workflows follows not only first principles but often relies on implicit conventions. Situs conventions related to map formats, resolution, correlation functions and feature detection are reviewed and summarized. The compatibility of the Situs workflow with CCP4 conventions and programs is discussed

Sulfur and octane trade off in FCC naphta conventional hydrotreating

Energy Technology Data Exchange (ETDEWEB)

Badra, C. [INTEVEP S.A. Research and Technological Support Center of Petroleos de Venzuela, Caracas (Venezuela). Dept. de Refinacion; Perez, J.A. [INTEVEP S.A. Research and Technological Support Center of Petroleos de Venzuela, Caracas (Venezuela). Dept. de Refinacion; Salazar, J.A. [INTEVEP S.A. Research and Technological Support Center of Petroleos de Venzuela, Caracas (Venezuela). Dept. de Refinacion; Cabrera, L. [INTEVEP S.A. Research and Technological Support Center of Petroleos de Venzuela, Caracas (Venezuela). Dept. de Refinacion; Gracia, W. [INTEVEP S.A. Research and Technological Support Center of Petroleos de Venzuela, Caracas (Venezuela). Dept. de Refinacion

1997-06-01

A model to predict the change of octane numbers expected in an FCC naphtha hydrotreating process as a function of the hydroprocessing severity (degree of sulfur removal) and the type of naphtha (expressed as the sulfur content and bromine number in the feedstock) is presented. When considering hydrotreating as an option for processing their catalytic naphthas, refiners search for the proper balance between the desired reduction of sulfur and olefins and the resulting undesired reduction of octane (RON and MON). In doing so, refiners should study the possibility of performing the hydrotreating at mild severities and/or the possibility of fractionating FCC naphthas to just treat a specific cut. This paper provides simple tools to study and analyze these study cases and to assess the sulfur-octane trade offs. (orig.)

The energy efficiency of crude oil refining in Brazil: A Brazilian refinery plant case

International Nuclear Information System (INIS)

Lima, Romulo S. de; Schaeffer, Roberto

2011-01-01

This article evaluates energy efficiency in Brazilian crude oil refining in comparison with the crude oil refining in the United States between 1930 and 2008. It aims to show that increased refinery complexity reduces the energy consumption of products of high value added. Moreover, the article shows that improvements in energy efficiency result in higher quality products and increased processing of oil. A Brazilian refinery with a capacity of 157,000 barrels per day (kbpd) was modernized in 2008 at a cost of US $1.3 billion. As a result, its capacity increased by 17%, from 157 to 189 kbpd. Its complexity index also rose from 3.2 to 6.8, allowing an improvement in the EII (energy intensity index) from 110% to 93%. In relation to the crude oil processed before being modernized, energy consumption fell from 0.75 to 0.52 MBtu (million British thermal units) per barrel processed. These proceedings show that increases in complexity reduce the energy consumed in the production of final products with high value added, such as gasoline, diesel and jet fuel. -- Highlights: → Increased refinery complexity reduces the energy consumption of products of high value added. → Improvements in refinery energy efficiency result in higher quality products and increased processing of oil. → Brazilian refineries were not affected significantly in the 2008 crisis, such as the US refineries, due to many factors. → The EII of Brazilian refining presents real opportunities for gains through changes in the profile of energy consumed.

Morse Set Classification and Hierarchical Refinement Using Conley Index

KAUST Repository

Guoning Chen,; Qingqing Deng,; Szymczak, A.; Laramee, R. S.; Zhang, E.

2012-01-01

Morse decomposition provides a numerically stable topological representation of vector fields that is crucial for their rigorous interpretation. However, Morse decomposition is not unique, and its granularity directly impacts its computational cost. In this paper, we propose an automatic refinement scheme to construct the Morse Connection Graph (MCG) of a given vector field in a hierarchical fashion. Our framework allows a Morse set to be refined through a local update of the flow combinatorialization graph, as well as the connection regions between Morse sets. The computation is fast because the most expensive computation is concentrated on a small portion of the domain. Furthermore, the present work allows the generation of a topologically consistent hierarchy of MCGs, which cannot be obtained using a global method. The classification of the extracted Morse sets is a crucial step for the construction of the MCG, for which the Poincar index is inadequate. We make use of an upper bound for the Conley index, provided by the Betti numbers of an index pair for a translation along the flow, to classify the Morse sets. This upper bound is sufficiently accurate for Morse set classification and provides supportive information for the automatic refinement process. An improved visualization technique for MCG is developed to incorporate the Conley indices. Finally, we apply the proposed techniques to a number of synthetic and real-world simulation data to demonstrate their utility. © 2006 IEEE.

Morse Set Classification and Hierarchical Refinement Using Conley Index

KAUST Repository

Guoning Chen,

2012-05-01

Morse decomposition provides a numerically stable topological representation of vector fields that is crucial for their rigorous interpretation. However, Morse decomposition is not unique, and its granularity directly impacts its computational cost. In this paper, we propose an automatic refinement scheme to construct the Morse Connection Graph (MCG) of a given vector field in a hierarchical fashion. Our framework allows a Morse set to be refined through a local update of the flow combinatorialization graph, as well as the connection regions between Morse sets. The computation is fast because the most expensive computation is concentrated on a small portion of the domain. Furthermore, the present work allows the generation of a topologically consistent hierarchy of MCGs, which cannot be obtained using a global method. The classification of the extracted Morse sets is a crucial step for the construction of the MCG, for which the Poincar index is inadequate. We make use of an upper bound for the Conley index, provided by the Betti numbers of an index pair for a translation along the flow, to classify the Morse sets. This upper bound is sufficiently accurate for Morse set classification and provides supportive information for the automatic refinement process. An improved visualization technique for MCG is developed to incorporate the Conley indices. Finally, we apply the proposed techniques to a number of synthetic and real-world simulation data to demonstrate their utility. © 2006 IEEE.

Refinements of the column generation process for the Vehicle Routing Problem with Time Windows

DEFF Research Database (Denmark)

Larsen, Jesper

2004-01-01

interval denoted the time window. The objective is to determine routes for the vehicles that minimizes the accumulated cost (or distance) with respect to the above mentioned constraints. Currently the best approaches for determining optimal solutions are based on column generation and Branch......-and-Bound, also known as Branch-and-Price. This paper presents two ideas for run-time improvements of the Branch-and-Price framework for the Vehicle Routing Problem with Time Windows. Both ideas reveal a significant potential for using run-time refinements when speeding up an exact approach without compromising...

Experimental investigation of different refining stages influences on optical and ultrasonic signals in paper pulp suspensions

International Nuclear Information System (INIS)

Jan, Niemi

2010-01-01

An important parameter to control in papermaking is the fiber mass fraction in the pulp suspension. Poor control to an unstable process that compromises the production, quality and the energy efficiency in the pulp mill. Using optical or ultrasound measurement techniques can obtain estimation of the mass fraction. Refining is an important operation in preparing the fibers for the paper machine. Refining influence the properties of the fiber by crushing the fiber, roughens the fiber surface and occasionally cut fibers and removes parts of the outer fiber wall leading to an increasing amount of short fibers (fines). A freeness tester was used for verify the changes in fiber properties at four different refining levels. The result shows that for unbleached softwood pulp the used measurement techniques either were not observable or minor. The results indicate that refining can potentially influence accurate consistency estimation for unbleached softwood pulp but for bleached hardwood pulp the influence is believed to be minor using the investigating measurement techniques

Effects of grain refinement on the biocorrosion and in vitro bioactivity of magnesium

Energy Technology Data Exchange (ETDEWEB)

Saha, Partha; Roy, Mangal [Department of Bioengineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Datta, Moni Kanchan [Department of Bioengineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Center for Complex Engineered Multifunctional Materials, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Lee, Boeun [Department of Bioengineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Kumta, Prashant N., E-mail: pkumta@pitt.edu [Department of Bioengineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Center for Complex Engineered Multifunctional Materials, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Mechanical Engineering and Materials Science, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Chemical and Petroleum Engineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); School of Dental Medicine, University of Pittsburgh, PA 15261 (United States); McGowan Institute of Regenerative Medicine, University of Pittsburgh, PA 15261 (United States)

2015-12-01

Magnesium is a new class of biodegradable metals potentially suitable for bone fracture fixation due to its suitable mechanical properties, high degradability and biocompatibility. However, rapid corrosion and loss in mechanical strength under physiological conditions render it unsuitable for load-bearing applications. In the present study, grain refinement was implemented to control bio-corrosion demonstrating improved in vitro bioactivity of magnesium. Pure commercial magnesium was grain refined using different amounts of zirconium (0.25 and 1.0 wt.%). Corrosion behavior was studied by potentiodynamic polarization (PDP) and mass loss immersion tests demonstrating corrosion rate decrease with grain size reduction. In vitro biocompatibility tests conducted by MC3T3-E1 pre-osteoblast cells and measured by DNA quantification demonstrate significant increase in cell proliferation for Mg–1 wt.% Zr at day 5. Similarly, alkaline phosphatase (ALP) activity was higher for grain refined Mg. Alloys were also tested for ability to support osteoclast differentiation using RAW264.7 monocytes with receptor activator of nuclear factor kappa-β ligand (RANKL) supplemented cell culture. Osteoclast differentiation process was observed to be severely restricted for smaller grained Mg. Overall, the results indicate grain refinement to be useful not only for improving corrosion resistance of Mg implants for bone fixation devices but also potentially modulate bone regeneration around the implant. - Highlights: • The biocorrosion and biocompatibility of pure Mg and Mg grain refined with different Zr levels were investigated. • Corrosion resistance in HBSS and compressive strength of pure Mg was significantly improved with Zr addition. • Electrochemical and immersion corrosion tests showed a fourfold decrease in corrosion rate of pure Mg with 1% Zr addition. • Grain refinement of pure Mg demonstrated enhanced osteoblast cell activity and proliferation.

Effects of grain refinement on the biocorrosion and in vitro bioactivity of magnesium

International Nuclear Information System (INIS)

Saha, Partha; Roy, Mangal; Datta, Moni Kanchan; Lee, Boeun; Kumta, Prashant N.

2015-01-01

Magnesium is a new class of biodegradable metals potentially suitable for bone fracture fixation due to its suitable mechanical properties, high degradability and biocompatibility. However, rapid corrosion and loss in mechanical strength under physiological conditions render it unsuitable for load-bearing applications. In the present study, grain refinement was implemented to control bio-corrosion demonstrating improved in vitro bioactivity of magnesium. Pure commercial magnesium was grain refined using different amounts of zirconium (0.25 and 1.0 wt.%). Corrosion behavior was studied by potentiodynamic polarization (PDP) and mass loss immersion tests demonstrating corrosion rate decrease with grain size reduction. In vitro biocompatibility tests conducted by MC3T3-E1 pre-osteoblast cells and measured by DNA quantification demonstrate significant increase in cell proliferation for Mg–1 wt.% Zr at day 5. Similarly, alkaline phosphatase (ALP) activity was higher for grain refined Mg. Alloys were also tested for ability to support osteoclast differentiation using RAW264.7 monocytes with receptor activator of nuclear factor kappa-β ligand (RANKL) supplemented cell culture. Osteoclast differentiation process was observed to be severely restricted for smaller grained Mg. Overall, the results indicate grain refinement to be useful not only for improving corrosion resistance of Mg implants for bone fixation devices but also potentially modulate bone regeneration around the implant. - Highlights: • The biocorrosion and biocompatibility of pure Mg and Mg grain refined with different Zr levels were investigated. • Corrosion resistance in HBSS and compressive strength of pure Mg was significantly improved with Zr addition. • Electrochemical and immersion corrosion tests showed a fourfold decrease in corrosion rate of pure Mg with 1% Zr addition. • Grain refinement of pure Mg demonstrated enhanced osteoblast cell activity and proliferation

Refining clean fuels for the future

International Nuclear Information System (INIS)

Courty, P.; Gruson, J.F.

2001-01-01

To which extent transportation fuels will reasonably be changed in the coming years? LPG and natural gas are expected to challenge conventional fuels, hydrogen and methanol are bounded to possible fuel cells development. Among others, security of supply, competitive economics and environmental protection issues will be the key to the changes in the coming years. But taking into account expected transportation development, liquid fuels from oil should prevail as the reference energy. Though most of technologies and catalysts needed for the future are still existing or under marketing plans, the industry has to cope with the growing share of middle distillates. Indeed future zero heavy fuel-oil refineries are technically feasible through many existing and recent technologies. However their potential profitability is weighed down deeply by the very high investments and operating costs which are tied up. Tomorrow's main gasoline challenges deal with sulfur in FCC gasoline, aromatics and olefins contents together with a possible ban of ethers, hampering future octane demand and its technical feasibility. In a similar way diesel oil issues for the future imply a very deep desulfurization with possible aromatics hydrogenation and rings opening in order to comply with cetane and poly-aromatics ratings. Natural gas upgrading via syngas chemistry is still expected to open the way to clean fuels for the future via improved and integrated FT's GTL technologies which could as a matter provide most of future increases in clean fuels demand without decreasing the related fatal carbon losses as CO 2 . As an overall view, clean fuels production for the future is technically feasible. Advanced hydro-refining and hydro-conversion technologies open the way to clean fuels and allow the best flexibility in the gasoline/middle distillates ratio. However cost reduction remains a key issue since the huge investments needed are faced with low and volatile refining margins. In addition, CO 2

Application of CAD/CAE/CAM in forging process: a review

International Nuclear Information System (INIS)

Ahmad Baharuddin Abdullah; Hamouda, A.M.S.

2005-01-01

Forging can be described as the process in which metal is plastically deformed with application of huge pressure. The process not only changes the shape but also improves the properties of the forged parts due to grain size refinement. Conventionally, the empirical trial and error method has been applied, but recently there are various tools are employed to improved product quality and economic of the process. For example, Computer Aided Design (CAD) is widely used in modeling of the process, while Computer Aided Engineering (CAE) tools have been utilized in analyzing the process. To physically demonstrate the process, Computer Aided Manufacturing (CAM) such as CNC machine has been exploited. In order to improve forging process efficiency, an integrated system that combines all advantages of CAD, CAM and CAE need to be developed. This paper presents an overview of computer aided simulation such as CAD, CAE and CAM application in forging process. (Author)

Patient radiation dose in conventional and xerographic cephalography

International Nuclear Information System (INIS)

Copley, R.L.; Glaze, S.A.; Bushong, S.C.; West, D.C.

1979-01-01

A comparison of the radiation doses for xeroradiographic and conventional film screen cephalography was made. Alderson tissue-equivalent phantoms were used for patient simulation. An optimum technique in terms of patient dose and image quality indicated that the dose for the Xerox process ranged from five to eleven times greater than that for the conventional process for entrance and exit exposures, respectively. This dose, however, falls within an acceptable range for other dental and medical radiation doses. It is recommended that conventional cephalography be used for routine purposes and that xeroradiography be reserved for situations requiring the increased image quality that the process affords

Electron microscopy investigation of the TiBAl and TiCAl grain refiner master alloys

International Nuclear Information System (INIS)

Cizek, P

2006-01-01

The present work brings a detailed statistical analysis of the microstructural characteristics and chemistry of the second phase particles present in the Al-5Ti-1B and Al- 3Ti-0.15C (wt.%) commercial grain refiner rods used in the Al casting industry. The investigation was performed using the TEM, EDS, STEM and HREM techniques. Both refiner rods contained large, blocky Al 3 Ti DO 22 particles. Borides present in the TiBAl rod, known to be main α-Al nucleation substrates, exhibited a facetted, hexagonal platelet morphology and largely represented a mixed (Ti,Al)B 2 phase, with Ti and Al contents changing continuously across the particle dimensions. There were two distinct families of small particles observed in the TiCAl rod. The coarser, facetted particles corresponded to cubic TiC crystal structure and these are believed to be major α-Al nucleation sites. The family of finer, round particles appeared to correspond to orthorhombic Al 6 Fe phase and their role in the nucleation process remains to be clarified. The results obtained may be used in optimising the grain refiner rod microstructures that would ensure improved refining performance during casting

Electron microscopy investigation of the TiBAl and TiCAl grain refiner master alloys

Energy Technology Data Exchange (ETDEWEB)

Cizek, P [IMMPETUS, Department of Engineering Materials, University of Sheffield, Mappin Street, Sheffield S1 3JD (United Kingdom)

2006-02-22

The present work brings a detailed statistical analysis of the microstructural characteristics and chemistry of the second phase particles present in the Al-5Ti-1B and Al- 3Ti-0.15C (wt.%) commercial grain refiner rods used in the Al casting industry. The investigation was performed using the TEM, EDS, STEM and HREM techniques. Both refiner rods contained large, blocky Al{sub 3}Ti DO{sub 22} particles. Borides present in the TiBAl rod, known to be main {alpha}-Al nucleation substrates, exhibited a facetted, hexagonal platelet morphology and largely represented a mixed (Ti,Al)B{sub 2} phase, with Ti and Al contents changing continuously across the particle dimensions. There were two distinct families of small particles observed in the TiCAl rod. The coarser, facetted particles corresponded to cubic TiC crystal structure and these are believed to be major {alpha}-Al nucleation sites. The family of finer, round particles appeared to correspond to orthorhombic Al{sub 6}Fe phase and their role in the nucleation process remains to be clarified. The results obtained may be used in optimising the grain refiner rod microstructures that would ensure improved refining performance during casting.

Preparation of Al-Ti-B grain refiner by SHS technology[Self-propagating High-temperature Synthesis

Energy Technology Data Exchange (ETDEWEB)

Nikitin, V.I.; Wanqi, J.I.E.; Kandalova, E.G.; Makarenko, A.G.; Yong, L.

2000-02-01

Since the discovery of the grain refinement effect of aluminum by titanium, especially with the existence of B or C in 1950, grain refiners are widely accepted in industry for microstructure control of aluminum alloys. Research on this topic is to obtain the highest grain refinement efficiency with the lowest possible addition of master alloy. It is widely accepted that the morphology and size of TiAl{sub 3} particles, which are known as heterogeneous nucleation centers, are important factors deterring the grain refinement efficiency. Fine TiAl{sub 3} particles are favorable. The grain refinement process shows a heredity phenomenon, which means that structural information from initial materials transfers through a melt to the final product. It is important to find the connection between microstructural parameters of the master alloy and the final product. To improve the quality of Al-Ti-B master alloys for the use as a grain refiner, a new method based on SHS (self-propagating high-temperature synthesis) technology has been developed in Samara State Technical University to produce the master alloys. SHS, as a new method for preparation of materials, was first utilized by Merzhanov in 1967. This method uses the energy from highly exothermic reactions to sustain the chemical reaction in a combustion wave. The advantages of SHS include simplicity, low energy requirement, and higher product purity. Because SHS reactions can take place between elemental reactants, it is easy to control product composition. The purposes of this investigation were to fabricate an SHS Al-5%Ti-1%B master alloy, to analyze its structure and to test its grain refining performance.

The decision-making process in Brazil's ratification of the World Health Organization Framework Convention on Tobacco Control.

Science.gov (United States)

Rangel, Erica Cavalcanti; Pereira, Andre; Cavalcante, Tania Maria; Oliveira, Egléubia Andrade; Silva, Vera Luiza da Costa E

2017-09-21

Tobacco consumption is a leading cause of various types of cancer and other tobacco-related diseases. In 2003, the World Health Assembly adopted the World Health Organization Framework Convention on Tobacco Control (WHO-FCTC), which aims to protect citizens from the health, social, environmental, and economic consequences of tobacco consumption and exposure to tobacco smoke. The Convention was to be ratified by the Member States of the WHO; in Brazil's case, ratification involved the National Congress, which held public hearings in the country's leading tobacco growing communities (municipalities). The current study analyzes this decision-making process according to the different interests, positions, and stakeholders. In methodological terms, this is a qualitative study based on document research, drawing primarily on the shorthand notes from the public hearings. We analyze the interests and arguments for and against ratification. The article shows that although preceded by intense debates, the final decision in favor of ratification was made by a limited group of government stakeholders, characterizing a decision-making process similar to a funnel.

Optimal algebraic multilevel preconditioning for local refinement along a line

NARCIS (Netherlands)

Margenov, S.D.; Maubach, J.M.L.

1995-01-01

The application of some recently proposed algebraic multilevel methods for the solution of two-dimensional finite element problems on nonuniform meshes is studied. The locally refined meshes are created by the newest vertex mesh refinement method. After the introduction of this refinement technique

The convention planning process: Potential impact of a high-level Nuclear Waste Repository in Nevada

International Nuclear Information System (INIS)

Kunreuther, H.; Easterling, D.; Kleindorfer, P.

1988-09-01

This report presents results from two studies that test whether a high level nuclear waste repository sites at Yucca Mountain, Nevada will diminish the willingness of meeting planners to schedule conventions, trade shows, and other meetings in Las Vegas. The first study, a focus group interview with nine meeting planners from the Philadelphia area, found little evidence that planners' selection decisions would be influenced by environmental hazards (e.g., earthquakes, pollution), unless planners were led to believe that these hazards would have a direct impact on convention delegates and the planner could conceivably be held personally responsible for any such impacts. Participants did point out that they would be sensitive to continued media coverage of a negative event, as this might stigmatize the city in the eyes of delegates. The results from the focus group guided the development of a larger and more formal questionnaire survey of meeting planners who were known to have selected Las Vegas for a meeting. Of the 153 planners recruited, 114 had a future meeting scheduled and 39 had arranged a meeting that was recently held in the city. Subjects first answered a number of questions that described the process by which they chose Las Vegas among the possible convention cities. They were then instructed to reconsider their decision in light of seven different scenarios pertaining to the repository at Yucca Mountain

Framework for understanding LENR processes, using conventional condensed matter physics

Energy Technology Data Exchange (ETDEWEB)

Chubb, Scott R. [Research Systems Inc., 9822 Pebble Weigh Ct., Burke VA 22015-3378 (United States)

2006-07-01

Conventional condensed matter physics provides a unifying framework for understanding low-energy nuclear reactions (LENRs) in solids. In the paper, standard many-body physics techniques are used to illustrate this fact. Specifically, the paper shows that formally the theories by Schwinger, Hagelstein, and Chubb and Chubb (C and C), all can be related to a common set of equations, associated with reaction rate and energy transfer, through a standard many-body physics procedure (R-matrix theory). In each case, particular forms of coherence are used that, implicitly provide a mechanism for understanding how LENRs can proceed without. the emission of high-energy particles. In addition, additional ideas, associated with Conventional Condensed Matter physics, are used to extend the earlier ion band state (IBS) model by C and C. The general model clarifies the origin of coherent. processes that initiate LENRs, through the onset of ion conduction that can occur through ionic fluctuations in nano-scale crystals. In the case of PdD{sub x}, these fluctuations begin to occur as x {yields} 1 in sub-lattice structures with characteristic dimensions of 60 nm. The resulting LENRs are triggered by the polarization between injected d's and electrons (immediately above the Fermi energy) that takes place in finite-size PdD crystals. During the prolonged charging of PdD{sub x} the applied, external electric field induces these fluctuations through a form of Zener tunneling that mimics the kind of tunneling, predicted by Zener, that is responsible for possible conduction (referred to as Zener-electric breakdown) in insulators. But because the fluctuations are ionic and they occur in PdD, nano-scale structures, a more appropriate characterization is Zener-ionic breakdown in nano-crystalline PdD. Using the underlying dynamics, it is possible to relate triggering times that are required for the initiation of the effect, to crystal size and externally applied fields. (authors)

RBT—A Tool for Building Refined Buneman Trees

DEFF Research Database (Denmark)

Besenbacher, Søren; Mailund; Westh-Nielsen, Lasse

2005-01-01

We have developed a tool implementing an efficient algorithm for refined Buneman tree reconstruction. The algorithm—which has the same complexity as the neighbour-joining method and the (plain) Buneman tree construction—enables refined Buneman tree reconstruction on large taxa sets....

Combined thermophilic aerobic process and conventional anaerobic digestion: effect on sludge biodegradation and methane production.

Science.gov (United States)

Dumas, C; Perez, S; Paul, E; Lefebvre, X

2010-04-01

The efficiency of hyper-thermophilic (65 degrees Celsius) aerobic process coupled with a mesophilic (35 degrees Celsius) digester was evaluated for the activated sludge degradation and was compared to a conventional mesophilic digester. For two Sludge Retention Time (SRT), 21 and 42 days, the Chemical Oxygen Demand (COD) solubilisation and biodegradation processes, the methanisation yield and the aerobic oxidation were investigated during 180 days. The best results were obtained at SRT of 44 days; the COD removal yield was 30% higher with the Mesophilic Anaerobic Digestion/Thermophilic Aerobic Reactor (MAD-TAR) co-treatment. An increase of the sludge intrinsic biodegradability is also observed (20-40%), showing that the unbiodegradable COD in mesophilic conditions becomes bioavailable. However, the methanisation yield was quite similar for both processes at a same SRT. Finally, such a process enables to divide by two the volume of digester with an equivalent efficiency. Copyright 2009 Elsevier Ltd. All rights reserved.

Comparing the impact of homogenization and heat processing on the properties and in vitro digestion of milk from organic and conventional dairy herds

Science.gov (United States)

The effects of homogenization and heat processing on the chemical and in vitro digestion traits of milk from organic and conventional herds were compared. Raw milk from organic (>50% of dry matter intake from pasture) and conventional (no access to pasture) farms were adjusted to commercial whole a...

Additional grain refinement in recrystallization controlled rolling of Ti-microalloyed steels processed by near-net-shape casting technology

International Nuclear Information System (INIS)

Arribas, M.; Lopez, B.; Rodriguez-Ibabe, J.M.

2008-01-01

This paper analyzes the recrystallization kinetics in Ti-microalloyed steels processed using 'beam blank' casting technology. The faster solidification rates associated with this technology brings a finer precipitation of TiN particles which are very effective in controlling austenite grain growth during hot working. Furthermore, these small precipitates have been shown to delay static and dynamic recrystallization. The finer the precipitates the higher the delay in recrystallization. Nevertheless, beyond particle size and distribution, the level of delay is very dependent on microstructure (above all austenite grain size) and deformation conditions (strain and temperature). This paper studies the effects of this recrystallization delay on the microstructure evolution during hot rolling. Special attention was paid to the study of the occurrence of partial recrystallization during the final stages of rolling, which could lead to the presence of mixed microstructures before transformation. The possibility of achieving an additional austenite grain size refinement prior to transformation was evaluated

India's refining prospects linked to economic growth

International Nuclear Information System (INIS)

Lewis, E.

1996-01-01

International investors assess refining ventures in India the same way they do comparable projects elsewhere in the world: according to their expectations about investment returns. By that standard, India's appeal is mixed, although its need for some measure of additional refining capacity seems certain. The success of future refinery investments will depend heavily on the government's commitment to policies allowing the economy to grow faster than the population. Unless accompanied by economic growth, expected increases in the population will not automatically raise demand for petroleum products. Decisions about investments in India's refining sector, therefore, must carefully weigh market fundamentals, the business environment, and likely investment performance. This paper reviews the market for the various products and predicts new economic trends

Friction-stir processing of a high-damping Mn-Cu alloy used for marine propellers

Energy Technology Data Exchange (ETDEWEB)

Lynch, S.P.; Edwards, D.P.; Majumdar, A. [Defence Science and Technology Organisation, Melbourne (Australia); Moutsos, S. [Centre for Advanced Materials Technology, Monash Univ. (Australia); Mahoney, M.W. [Rockwell Scientific, Thousand Oaks (United States)

2003-07-01

Mn-Cu alloys are used for specialised applications, such as marine propellers, where high noise-damping characteristics are required. These alloys tend to have more severe shrinkage porosity than conventional propeller alloys, and the corrosion resistance (including stress-corrosion and corrosion-fatigue resistance) of the alloys is not as high as desirable. Friction-stir processing (FSP) trials on one such alloy (tradename Sonoston) have shown that near-surface porosity can be eliminated and that the coarse, as-cast microstructure can be significantly refined. The corrosion resistance of processed material is substantially improved provided a heat treatment to relieve residual stress is carried out after FSP. (orig.)

Refinement-Animation for Event-B - Towards a Method of Validation

DEFF Research Database (Denmark)

Hallerstede, Stefan; Leuschel, Michael; Plagge, Daniel

2010-01-01

We provide a detailed description of refinement in Event-B, both as a contribution in itself and as a foundation for the approach to simultaneous animation of multiple levels of refinement that we propose. We present an algorithm for simultaneous multi-level animation of refinement, and show how ...

Cleaning Data with OpenRefine

Directory of Open Access Journals (Sweden)

Seth van Hooland

2013-08-01

Full Text Available Duplicate records, empty values and inconsistent formats are phenomena we should be prepared to deal with when using historical data sets. This lesson will teach you how to discover inconsistencies in data contained within a spreadsheet or a database. As we increasingly share, aggregate and reuse data on the web, historians will need to respond to data quality issues which inevitably pop up. Using a program called OpenRefine, you will be able to easily identify systematic errors such as blank cells, duplicates, spelling inconsistencies, etc. OpenRefine not only allows you to quickly diagnose the accuracy of your data, but also to act upon certain errors in an automated manner.

Outlook for Canadian refining

International Nuclear Information System (INIS)

Boje, G.

1998-01-01

The petroleum supply and demand balance was discussed and a comparison between Canadian and U.S. refineries was provided. The impact of changing product specifications on the petroleum industry was also discussed. The major changes include sulphur reductions in gasoline, benzene and MMT additives. These changes have been made in an effort to satisfy environmental needs. Geographic margin variations in refineries between east and west were reviewed. An overview of findings from the Solomon Refining Study of Canadian and American refineries, which has been very complimentary of the Canadian refining industry, was provided. From this writer's point of view refinery utilization has improved but there is a threat from increasing efficiency of US competitors. Environmental issues will continue to impact upon the industry and while the chances for making economic returns on investment are good for the years ahead, it will be a challenge to maintain profitability

Construction and Application of a Refined Hospital Management Chain.