WorldWideScience

Sample records for convection turbulent heat

  1. Heat transport in bubbling turbulent convection.

    Science.gov (United States)

    Lakkaraju, Rajaram; Stevens, Richard J A M; Oresta, Paolo; Verzicco, Roberto; Lohse, Detlef; Prosperetti, Andrea

    2013-06-04

    Boiling is an extremely effective way to promote heat transfer from a hot surface to a liquid due to numerous mechanisms, many of which are not understood in quantitative detail. An important component of the overall process is that the buoyancy of the bubble compounds with that of the liquid to give rise to a much-enhanced natural convection. In this article, we focus specifically on this enhancement and present a numerical study of the resulting two-phase Rayleigh-Bénard convection process in a cylindrical cell with a diameter equal to its height. We make no attempt to model other aspects of the boiling process such as bubble nucleation and detachment. The cell base and top are held at temperatures above and below the boiling point of the liquid, respectively. By keeping this difference constant, we study the effect of the liquid superheat in a Rayleigh number range that, in the absence of boiling, would be between 2 × 10(6) and 5 × 10(9). We find a considerable enhancement of the heat transfer and study its dependence on the number of bubbles, the degree of superheat of the hot cell bottom, and the Rayleigh number. The increased buoyancy provided by the bubbles leads to more energetic hot plumes detaching from the cell bottom, and the strength of the circulation in the cell is significantly increased. Our results are in general agreement with recent experiments on boiling Rayleigh-Bénard convection.

  2. Heat transport measurements in turbulent rotating Rayleigh-Benard convection

    Energy Technology Data Exchange (ETDEWEB)

    Ecke, Robert E [Los Alamos National Laboratory; Liu, Yuanming [Los Alamos National Laboratory

    2008-01-01

    We present experimental heat transport measurements of turbulent Rayleigh-Benard convection with rotation about a vertical axis. The fluid, water with Prandtl number ({sigma}) about 6, was confined in a cell which had a square cross section of 7.3 cm x 7.3 cm and a height of 9.4 cm. Heat transport was measured for Rayleigh numbers 2 x 10{sup 5} < Ra < 5 x 10{sup 8} and Taylor numbers 0 < Ta < 5 x 10{sup 9}. We show the variation of normalized heat transport, the Nusselt number, at fixed dimensional rotation rate {Omega}{sub D}, at fixed Ra varying Ta, at fixed Ta varying Ra, and at fixed Rossby number Ro. The scaling of heat transport in the range 10{sup 7} to about 10{sup 9} is roughly 0.29 with a Ro dependent coefficient or equivalently is also well fit by a combination of power laws of the form a Ra{sup 1/5} + b Ra{sup 1/3} . The range of Ra is not sufficient to differentiate single power law or combined power law scaling. The overall impact of rotation on heat transport in turbulent convection is assessed.

  3. Convective Heat Transfer Analysis in Fluid Flow with Turbulence Promoters with Heat Pipes

    Directory of Open Access Journals (Sweden)

    Theodor Mateescu

    2007-01-01

    Full Text Available The present paper proposes the analysis and the simulation of the convection heat transfer into the fluid flow with turbulence promoters utilizing heat pipes. The study is based on the necesity of the unconventional energy forms capitalization, increasing of the energy efficiency and leads to the energy consumtion decrease in concordance with the sustainable development concept.

  4. Turbulent mixed convection in asymmetrically heated vertical channel

    Directory of Open Access Journals (Sweden)

    Mokni Ameni

    2012-01-01

    Full Text Available In this paper an investigation of mixed convection from vertical heated channel is undertaken. The aim is to explore the heat transfer obtained by adding a forced flow, issued from a flat nozzle located in the entry section of a channel, to the up-going fluid along its walls. Forced and free convection are combined studied in order to increase the cooling requirements. The study deals with both symmetrically and asymmetrically heated channel. The Reynolds number based on the nozzle width and the jet velocity is assumed to be 3 103 and 2.104; whereas, the Rayleigh number based on the channel length and the wall temperature difference varies from 2.57 1010 to 5.15 1012. The heating asymmetry effect on the flow development including the mean velocity and temperature the local Nusselt number, the mass flow rate and heat transfer are examined.

  5. Numerical modeling of turbulence mixed convection heat transfer in air filled enclosures by finite volume method

    Directory of Open Access Journals (Sweden)

    M Safaei

    2016-09-01

    Full Text Available In the present study, first the turbulent natural convection and then laminar mixed convection of air flow was solved in a room and the calculated outcomes are compared with results of other scientists and after showing validation of calculations, aforementioned flow is solved as a turbulent mixed convection flow, using the valid turbulence models Standard k-ε, RNG k-ε and RSM. To solve governing differential equations for this flow, finite volume method was used. This method is a specific case of residual weighting method. The results show that at high Richardson Numbers, the flow is rather stationary at the center of the enclosure. Moreover, it is distinguished that when Richardson Number increases the maximum of local Nusselt decreases. Therefore, it can be said that less number of Richardson Number, more rate of heat transfer.

  6. Estimation of boundary heat flux using experimental temperature data in turbulent forced convection flow

    Science.gov (United States)

    Parwani, Ajit K.; Talukdar, Prabal; Subbarao, P. M. V.

    2015-03-01

    Heat flux at the boundary of a duct is estimated using the inverse technique based on conjugate gradient method (CGM) with an adjoint equation. A two-dimensional inverse forced convection hydrodynamically fully developed turbulent flow is considered. The simulations are performed with temperature data measured in the experimental test performed on a wind tunnel. The results show that the present numerical model with CGM is robust and accurate enough to estimate the strength and position of boundary heat flux.

  7. Entropy Generation Analysis and Performance Evaluation of Turbulent Forced Convective Heat Transfer to Nanofluids

    Directory of Open Access Journals (Sweden)

    Yu Ji

    2017-03-01

    Full Text Available The entropy generation analysis of fully turbulent convective heat transfer to nanofluids in a circular tube is investigated numerically using the Reynolds Averaged Navier–Stokes (RANS model. The nanofluids with particle concentration of 0%, 1%, 2%, 4% and 6% are treated as single phases of effective properties. The uniform heat flux is enforced at the tube wall. To confirm the validity of the numerical approach, the results have been compared with empirical correlations and analytical formula. The self-similarity profiles of local entropy generation are also studied, in which the peak values of entropy generation by direct dissipation, turbulent dissipation, mean temperature gradients and fluctuating temperature gradients for different Reynolds number as well as different particle concentration are observed. In addition, the effects of Reynolds number, volume fraction of nanoparticles and heat flux on total entropy generation and Bejan number are discussed. In the results, the intersection points of total entropy generation for water and four nanofluids are observed, when the entropy generation decrease before the intersection and increase after the intersection as the particle concentration increases. Finally, by definition of Ep, which combines the first law and second law of thermodynamics and attributed to evaluate the real performance of heat transfer processes, the optimal Reynolds number Reop corresponding to the best performance and the advisable Reynolds number Read providing the appropriate Reynolds number range for nanofluids in convective heat transfer can be determined.

  8. Prandtl-, Rayleigh-, and Rossby-number dependence of heat transport in turbulent rotating Rayleigh-Bénard convection

    NARCIS (Netherlands)

    Zhong, Jin-Qiang; Stevens, Richard Johannes Antonius Maria; Clercx, H.J.H.; Verzicco, Roberto; Verzicco, Roberto; Lohse, Detlef; Ahlers, Günter

    Experimental and numerical data for the heat transfer as a function of the Rayleigh, Prandtl, and Rossby numbers in turbulent rotating Rayleigh-Bénard convection are presented. For relatively small Ra $\\approx 10^8$ and large Pr modest rotation can enhance the heat transfer by up to 30%. At larger

  9. Aspect ratio dependence of heat transfer and large-scale flow in turbulent convection

    CERN Document Server

    Bailon-Cuba, Jorge; Schumacher, Joerg

    2010-01-01

    The heat transport and corresponding changes in the large-scale circulation (LSC) in turbulent Rayleigh-B\\'{e}nard convection are studied by means of three-dimensional direct numerical simulations as a function of the aspect ratio $\\Gamma$ of a closed cylindrical cell and the Rayleigh number $Ra$. For small and moderate aspect ratios, the global heat transfer law $Nu=A\\times Ra^{\\beta}$ shows a power law dependence of both fit coefficients $A$ and $\\beta$ on the aspect ratio. A minimum Nusselt number coincides with the point where the LSC undergoes a transition from a single-roll to a double-roll pattern. With increasing aspect ratio, we detect complex multi-roll LSC configurations. The aspect ratio dependence of the turbulent heat transfer for small and moderate $\\Gamma$ is in line with a varying amount of energy contained in the LSC, as quantified by the Proper Orthogonal Decomposition analysis. For $\\Gamma\\gtrsim 8$ the heat transfer becomes independent of the aspect ratio.

  10. Heat convection

    Energy Technology Data Exchange (ETDEWEB)

    Jiji, L.M. [City Univ. of New York, NY (United States). Dept. of Mechanical Engineering

    2006-07-01

    Professor Jiji's broad teaching experience lead him to select the topics for this book to provide a firm foundation for convection heat transfer with emphasis on fundamentals, physical phenomena, and mathematical modelling of a wide range of engineering applications. Reflecting recent developments, this textbook is the first to include an introduction to the challenging topic of microchannels. The strong pedagogic potential of Heat Convection is enhanced by the following ancillary materials: (1) Power Point lectures, (2) Problem Solutions, (3) Homework Facilitator, and, (4) Summary of Sections and Chapters. (orig.)

  11. Turbulent mixed convection of heat and water vapor transfers in a two-dimensional vegetation canopy

    Energy Technology Data Exchange (ETDEWEB)

    Banna, M. [Laboratoire sur l' Energie Solaire, Universite de Lome, Faculte des Sciences, BP 1515, Lome (Togo); Pietri, L.; Zeghmati, B. [Centre d' Etudes Fondamentales, Groupe de Mecanique Acoustique et Instrumentation (CEF-GMAI), Universite de Perpignan, 52 avenue de Villeneuve, 66860 Perpignan (France)

    2004-08-01

    The present study consists in a numerical investigation of turbulent mixed-convection of heat and water vapor transfers inside two-dimensional (2-D) vegetation canopy, in the surrounding atmosphere and in a wet underground. The time-averaged Navier-Stokes equations are used to characterize the flow field surrounding the canopy and within it. Reynolds shear stresses are calculated using the eddy turbulence model and the Prandtl mixing length. The governing equations are solved numerically using an implicit finite difference method and Thomas algorithm. The present model is used for the determination of the micro climatic profiles such as streamlines, isotherms and iso-concentration. Special emphasis is laid on the systematic analysis of the total evaporation rate (evapotranspiration), the local and average heat fluxes, the Nusselt and Sherwood numbers. The effects of Leaf Area Density distribution, the canopy stomata regulation, as well as the atmospheric forcing conditions on the transfers, are presented and analysed. The results show that buoyancy force caused by properties variation reduces the local heat and mass transfer coefficients, and that this reduction increases at lower wind velocities. (orig.)

  12. Phenomenology of turbulent convection

    Science.gov (United States)

    Verma, Mahendra; Chatterjee, Anando; Kumar, Abhishek; Samtaney, Ravi

    2016-11-01

    We simulate Rayleigh-Bénard convection (RBC) in which a fluid is confined between two thermally conducting plates. We report results from direct numerical simulation (DNS) of RBC turbulence on 40963 grid, the highest resolution hitherto reported, on 65536 cores of Cray XC40, Shaheen II, at KAUST. The non-dimensional parameters of our simulation are: the Rayleigh number Ra = 1 . 1 ×1011 (the highest ever for a pseudo-spectral simulation) and Prandtl number of unity. We present energy flux diagnostics of shell-to-shell (in wave number space) transfer. Furthermore, noting that convective flows are anisotropic due to buoyancy, we quantify anisotropy by subdividing each wavenumber shell into rings and quantify ring energy spectrum. An outstanding question in convective turbulence is the wavenumber scaling of the energy spectrum. Our pseudo-spectral simulations of turbulent thermal convection coupled with novel energy transfer diagnostics have provided a definitive answer to this question. We conclude that convective turbulence exhibits behavior similar to fluid turbulence, that is, Kolmogorov's k - 5 / 3 spectrum with forward and local energy transfers, along with a nearly isotropic energy distribution. The supercomputer Shaheen at KAUST was utilized for the simulations.

  13. Numerical study of natural turbulent convection of nanofluids in a tall cavity heated from below

    Directory of Open Access Journals (Sweden)

    Mebrouk Ridha

    2016-01-01

    Full Text Available In the present paper a numerical study of natural turbulent convection in a tall cavity filled with nanofluids. The cavity has a heat source embedded on its bottom wall, while the left, right and top walls of the cavity are maintained at a relatively low temperature. The working fluid is a water based nanofluid having three nanoparticle types: alumina, copper and copper oxid. The influence of pertinent parameters such as Rayleigh number, the type of nanofluid and solid volume fraction of nanoparticles on the cooling performance is studied. Steady forms of twodimensional Reynolds-Averaged-Navier-Stokes equations and conservation equations of mass and energy, coupled with the Boussinesq approximation, are solved by the control volume based discretisation method employing the SIMPLE algorithm for pressure-velocity coupling. Turbulence is modeled using the standard k-ε model. The Rayleigh number, Ra, is varied from 2.491009 to 2.491011. The volume fractions of nanoparticles were varied in the interval 0≤φ≤ 6% . Stream lines, isotherms, velocity profiles and Temperature profiles are presented for various combinations of Ra, the type of nanofluid and solid volume fraction of nanoparticles. The results are reported in the form of average Nusselt number on the heated wall. It is shown that for all values of Ra, the average heat transfer rate from the heat source increases almost linearly and monotonically as the solid volume fraction increases. Finally the average heat transfer rate takes on values that decrease according to the ordering Cu, CuO and Al2O3.

  14. Numerical study of forced convection in a turbulent heat sink made of several rows of blocks of square form

    Science.gov (United States)

    Bouchenafa, Rachid; Saim, Rachid; Abboudi, Said

    2015-09-01

    Forced convection is a phenomenon associated with the heat transfer fluid flows. The presence of convection affects simultaneously the thermal and hydrodynamic fields, the problem is thus coupled. This form of heat transfer inside ducts occurs in many practical applications such as solar collectors, heat exchangers, cooling of electronic components as well as chemical and nuclear. In this work, we are interested primarily for a numerical study of thermo-hydraulic performances of an incompressible turbulent flow of air through a heat sink composed of several rows of bars of square section. Profiles and the axial velocity fields, as well as profiles and the distribution of the Nusselt number are plotted for all the geometry considered and chosen for different sections. The effects of geometrical parameters of the model and the operating parameters on the dynamic and thermal behavior of the air are analyzed.

  15. The influence of tip clearance and Prandtl number on turbulent forced convection heat transfer of rectangular fins

    Science.gov (United States)

    Park, Hae-Kyun; Chung, Bum-Jin

    2016-12-01

    The turbulent forced convection heat transfer of rectangular fins in a duct was investigated by varying the tip clearance and Pr. Mass transfer experiments using a H2SO4-CuSO4 electroplating system were performed based on the analogy between heat and mass transfers. FLUENT 6.3 was used for calculations. Turbulent models were tested and the Reynolds Stress Model was chosen, which showed a 1.15 % discrepancy with the existing correlation for a simple tube flow when Pr = 2, but 13 % when Pr = 2014. For a more complex fin channel, the discrepancy increased up to 30 %. The optimal tip clearances, corresponding to maximum heat transfer rates, did not vary with Pr, which is explained using the temperature contours. The results were also compared with the laminar case where Pr influenced the optimal tip clearance.

  16. Two-Dimensional Problem of Turbulent Natural Convection in a Semi-Open Cavity with Radiant Heating of Internal Boundaries

    Directory of Open Access Journals (Sweden)

    Nee Alexander

    2016-01-01

    Full Text Available Mathematical modelling of turbulent natural convection in a semi-open cavity with a heat-conducting walls of finite thickness with radiant heating of internal boundaries was performed. Two-dimensional problem of the conjugate heat transfer was solved by means of the finite difference method. Scale influence of open boundaries and radiant heating of the gas – wall interfaces on the formation of differential and integral heat transfer characteristics was established. An increase in the dimensionless time (τ led to displacement of extremum temperatures in the typical cross section (Y = 0.5 to an open vertical boundary. The average Nusselt number monotonically increased at the gas – a wall interfaces in a range of 400<τ<1200.

  17. Large-scale flow structures and heat transport of turbulent forced and mixed convection in a closed rectangular cavity

    Energy Technology Data Exchange (ETDEWEB)

    Schmeling, D., E-mail: Daniel.Schmeling@dlr.de [German Aerospace Center (DLR), Institute of Aerodynamics and Flow Technology, Bunsenstrasse 10, D-37073 Goettingen (Germany); Westhoff, A.; Kuehn, M.; Bosbach, J.; Wagner, C. [German Aerospace Center (DLR), Institute of Aerodynamics and Flow Technology, Bunsenstrasse 10, D-37073 Goettingen (Germany)

    2011-10-15

    Highlights: > Superposition of forced and thermal convection is studied in a rectangular cavity. > For pure forced convection the mean wind exhibits a solid body rotation. > Four buoyancy induced convection rolls are formed for mixed convection at Ar {approx} 3.3. > The enthalpy flux difference between out- and inflowing air has a maximum at Ar {approx} 0.6. - Abstract: Results of an experimental study of flow structure formation and heat transport in turbulent forced and mixed convection are presented. The experiments were conducted in a rectangular cavity with a square cross section, which has an aspect ratio between length and height of {Gamma}{sub xz} = 5. Air at atmospheric pressure was used as working fluid. The air inflow was supplied through a slot below the ceiling, while exhausting was provided by another slot, which is located directly above the floor. Both vents extend over the whole length of the cell. In order to induce thermal convection the bottom of the cell is heated while the ceiling is maintained at a constant temperature. This configuration allows to generate and study mixed convection under well defined conditions. Results of forced convection at Re = 1.07 x 10{sup 4} as well as mixed convection at 1.01 x 10{sup 4} {<=} Re {<=} 3.4 x 10{sup 4} and Ra = 2.4 x 10{sup 8} (3.3 {>=} Ar {>=} 0.3), which were obtained by means of Particle Image Velocimetry and local temperature measurements, are presented. For purely forced convection a 2D mean wind, which can be approximated by a solid body rotation, is found. With increasing Archimedes number this structure becomes unstable, leading to a transition of the solid body rotation into additional smaller convection rolls. Proper orthogonal decomposition of the instantaneous velocity fields has been performed for further analysis of these coherent large-scale structures. Their fingerprint is found in the spatial temperature distribution of the out flowing air at the end of the outlet channel, which

  18. Effect of turbulence models on predicting convective heat transfer to hydrocarbon fuel at supercritical pressure

    Directory of Open Access Journals (Sweden)

    Tao Zhi

    2016-10-01

    Full Text Available A variety of turbulence models were used to perform numerical simulations of heat transfer for hydrocarbon fuel flowing upward and downward through uniformly heated vertical pipes at supercritical pressure. Inlet temperatures varied from 373 K to 663 K, with heat flux ranging from 300 kW/m2 to 550 kW/m2. Comparative analyses between predicted and experimental results were used to evaluate the ability of turbulence models to respond to variable thermophysical properties of hydrocarbon fuel at supercritical pressure. It was found that the prediction performance of turbulence models is mainly determined by the damping function, which enables them to respond differently to local flow conditions. Although prediction accuracy for experimental results varied from condition to condition, the shear stress transport (SST and launder and sharma models performed better than all other models used in the study. For very small buoyancy-influenced runs, the thermal-induced acceleration due to variations in density lead to the impairment of heat transfer occurring in the vicinity of pseudo-critical points, and heat transfer was enhanced at higher temperatures through the combined action of four thermophysical properties: density, viscosity, thermal conductivity and specific heat. For very large buoyancy-influenced runs, the thermal-induced acceleration effect was over predicted by the LS and AB models.

  19. Turbulent Mixed Convection of a Nanofluid in a Horizontal Circular Tube with Non-Uniform Wall Heat Flux Using a Two-Phase Approach

    Directory of Open Access Journals (Sweden)

    F. Vahidinia

    2015-06-01

    Full Text Available In this paper, Turbulent mixed convective heat transfer of water and Al2O3 nanofluid has been numerically studied in a horizontal tube under non-uniform heat flux on the upper wall and insulation in the lower wall using mixture model. For the discretization of governing equations, the second-order upstream difference scheme and finite volume method were used. The coupling of pressure and velocity was established by using SIMPLEC algorithm. The calculated results demonstrated that the convective heat transfer coefficient of nanofluid is higher than of the base fluid and by increasing the nanoparticles volume fraction, the convective heat transfer coefficient and shear stress on the wall increase. On the other hand, with increasing the Grashof number, the shear stress and convective heat transfer coefficient decrease.

  20. Forced convection heat transfer with microencapsulated phase-change-material slurries. Turbulent flow in a circular tube; Microcapsuleka sohenka busshitsu slurries no kyosei tairyu netsudentatsu tokusei. Enkannai ranryu

    Energy Technology Data Exchange (ETDEWEB)

    Yamagishi, Y.; Sugano, T. [Daido Hoxan Inc., Hokkaido (Japan); Takeuchi, H.; Pyatenko, A. [Hokkaido National Industrial Research Institute Sapporo (Japan)

    1998-01-01

    An experimental study using a slurry of micro-encapsulated phase change material (MCPCM) in water is conducted in order to investigate the increase in convection heat transfer coefficients of slurry flows as well as the increase in thermal capacity of a slurry by using the latent heat from a solid-liquid phase change material (PCM). Experiments were done for turbulent, hydrodynamically fully developed flows in a circular tube with constant wall heat flux. Local convective heat transfer coefficients were measured along the heating test section in order to study the effects of the melting phenomena inside MCPCMs. Experimental data are presented for various particle concentrations, slurry flow rates, and heating rates. Results show that an increase in the local convective heat transfer coefficient is found when the MCPCMs melted. Enhancement of heat transfer due to phase change is affected to varying degrees by Reynolds numbers of slurry flows, the fraction of PCM which is solid phase and heating rates. This paper provides and presents an explanation of the physical mechanism of the convective heat transfer enhancement due to the phase change of MCPCMs and a set of data available for the adjustments of system operating conditions for optimum heat transfer performance. 15 refs., 11 figs., 4 tabs.

  1. Convective heat transfer

    CERN Document Server

    Kakac, Sadik; Pramuanjaroenkij, Anchasa

    2014-01-01

    Intended for readers who have taken a basic heat transfer course and have a basic knowledge of thermodynamics, heat transfer, fluid mechanics, and differential equations, Convective Heat Transfer, Third Edition provides an overview of phenomenological convective heat transfer. This book combines applications of engineering with the basic concepts of convection. It offers a clear and balanced presentation of essential topics using both traditional and numerical methods. The text addresses emerging science and technology matters, and highlights biomedical applications and energy technologies. What’s New in the Third Edition: Includes updated chapters and two new chapters on heat transfer in microchannels and heat transfer with nanofluids Expands problem sets and introduces new correlations and solved examples Provides more coverage of numerical/computer methods The third edition details the new research areas of heat transfer in microchannels and the enhancement of convective heat transfer with nanofluids....

  2. Two-dimensional turbulent convection

    Science.gov (United States)

    Mazzino, Andrea

    2017-11-01

    We present an overview of the most relevant, and sometimes contrasting, theoretical approaches to Rayleigh-Taylor and mean-gradient-forced Rayleigh-Bénard two-dimensional turbulence together with numerical and experimental evidences for their support. The main aim of this overview is to emphasize that, despite the different character of these two systems, especially in relation to their steadiness/unsteadiness, turbulent fluctuations are well described by the same scaling relationships originated from the Bolgiano balance. The latter states that inertial terms and buoyancy terms balance at small scales giving rise to an inverse kinetic energy cascade. The main difference with respect to the inverse energy cascade in hydrodynamic turbulence [R. H. Kraichnan, "Inertial ranges in two-dimensional turbulence," Phys. Fluids 10, 1417 (1967)] is that the rate of cascade of kinetic energy here is not constant along the inertial range of scales. Thanks to the absence of physical boundaries, the two systems here investigated turned out to be a natural physical realization of the Kraichnan scaling regime hitherto associated with the elusive "ultimate state of thermal convection" [R. H. Kraichnan, "Turbulent thermal convection at arbitrary Prandtl number," Phys. Fluids 5, 1374-1389 (1962)].

  3. Modulation of the wall-heat transfer in turbulent thermomagnetic convection by magnetic field gradients

    NARCIS (Netherlands)

    Kenjeres, S.; Zinsmeester, R.; Pyrda, L.; Fornalik-Wajs, E.; Szmyd, J.

    2015-01-01

    We present combined experimental and numerical studies of the heat transfer of paramagnetic or diamagnetic fluid inside a differentially heated cubical enclosure subjected to the magnetic field gradients of different strength and orientation. In contrast to the previously reported studies in

  4. Convection heat transfer

    CERN Document Server

    Bejan, Adrian

    2013-01-01

    Written by an internationally recognized authority on heat transfer and thermodynamics, this second edition of Convection Heat Transfer contains new and updated problems and examples reflecting real-world research and applications, including heat exchanger design. Teaching not only structure but also technique, the book begins with the simplest problem solving method (scale analysis), and moves on to progressively more advanced and exact methods (integral method, self similarity, asymptotic behavior). A solutions manual is available for all problems and exercises.

  5. Turbulent natural convection in a differentially heated cavity of aspect ratio 5 filled with non-participating and participating grey media

    Energy Technology Data Exchange (ETDEWEB)

    Capdevila, R; Trias, F X; Perez-Segarra, C D [Centre Tecnologic de Transferencia de Calor (CTTC), Lab.Termotecnia i Energetica, Universitat Politecnica de Catalunya (UPC), C/Colom, 11, E08222 Terrassa, Barcelona (Spain); Lehmkuhl, O; Colomer, G, E-mail: cttc@cttc.upc.edu, E-mail: termofluids@termofluids.com [Termofluids, S. L., Magi Colet 8, E08204 Sabadell, Barcelona (Spain)

    2011-12-22

    In the present work, turbulent natural convection in a tall differentially heated cavity of aspect ratio 5:1, filled with air (Pr = 0.7) under a Rayleigh number based on the height of 4.5 {center_dot} 10{sup 10}, is studied numerically. Two different situations have been analysed. In the first one, the cavity is filled with a transparent medium. In the second one, the cavity contains a grey participating gas. The turbulent flow is described by means of Large Eddy Simulation (LES) using symmetry-preserving discretizations. Simulations are compared with experimental data available in the literature and with Direct Numerical Simulations (DNS). Surface and gas radiation have been simulated using the Discrete Ordinates Method (DOM). The influence of radiation on fluid flow behaviour has also been analysed.

  6. Experimental investigation of turbulent mixed convection in the wake of a heated sphere; Experimentelle Untersuchung turbulenter Mischkonvektion im Nachlauf einer beheizten Kugel

    Energy Technology Data Exchange (ETDEWEB)

    Suckow, D.

    1993-11-01

    The axisymmetric wake of a heated sphere under conditions of turbulent mixed convection is investigated in the water test section FLUTMIK. The sphere is located in a vertical channel with forced convective upward flow. The influence of buoyancy forces to the flow field is studied by comparison with the unheated wake. The theoretical fundamentals describing turbulent flows and different versions of the k-{epsilon} turbulence model extended by buoyancy terms are described in detail. The quantities to be determined experimentally are derived. The temperature and the components of the velocity vector in axial and radial directions are measured simultaneously by means of a thermocouple probe and a two component, two color laser Doppler anemometer. The flow quantities are determined at axial distances between 5 and 106 sphere diameters. The functional principle and the basis of the laser Doppler anemometer are explained. The mean velocity, the mean temperature, the intensities of their fluctuations and the turbulent exchange quantities of momentum and heat transport are calculated. The decay laws of the quantities along the axis of the channel and the radial profiles are indicated and discussed. The applicability of the experimental results of the axisymmetric buoyancy influenced turbulent wake with respect to the turbulence models presented are shown. (orig.) [Deutsch] In der Wasser-Teststrecke FLUTMIK wird der achsensymmetrische Nachlauf stromab einer beheizten Kugel untersucht. Die Kugel befindet sich in einem vertikal angeordneten Kanal, der von unten nach oben turbulent zwangsdurchstroemt wird. Ein Vergleich mit dem unbeheizten Nachlauf zeigt den Einfluss von Auftriebskraeften auf das Stroemungsfeld. Die theoretischen Grundlagen zur Beschreibung turbulenter Stroemungen und verschiedene auftriebserweiterte Formen des k-{epsilon} Turbulenzmodells werden ausfuehrlich dargestellt. Die experimentell zu bestimmenden Groessen leiten sich hieraus ab. Die Temperatur und die

  7. Dynamical and statistical phenomena of circulation and heat transfer in periodically forced rotating turbulent Rayleigh-Benard convection

    CERN Document Server

    Sterl, Sebastian; Zhong, Jin-Qiang

    2016-01-01

    In this paper, we present results from an experimental study into turbulent Rayleigh-Benard convection forced externally by periodically modulated unidirectional rotation rates. We find that the azimuthal rotation velocity $\\dot{\\theta}$(t) and thermal amplitude $\\delta$(t) of the large-scale circulation (LSC) are modulated by the forcing, exhibiting a variety of dynamics including increasing phase delays and a resonant peak in the amplitude of $\\dot{\\theta}$(t). We also focus on the influence of modulated rotation rates on the frequency of occurrence $\\eta$ of stochastic cessation/reorientation events, and on the interplay between such events and the periodically modulated response of $\\dot{\\theta}$(t). Here we identify a mechanism by which $\\eta$ can be amplfied by the modulated response and these normally stochastic events can occur with high regularity. We provide a modeling framework that explains the observed amplitude and phase responses, and extend this approach to make predictions for the occurrence ...

  8. Turbulent convection in liquid metal with and without rotation.

    Science.gov (United States)

    King, Eric M; Aurnou, Jonathan M

    2013-04-23

    The magnetic fields of Earth and other planets are generated by turbulent, rotating convection in liquid metal. Liquid metals are peculiar in that they diffuse heat more readily than momentum, quantified by their small Prandtl numbers, Pr convection experiments in the liquid metal gallium (Pr = 0.025) over a range of nondimensional buoyancy forcing (Ra) and rotation periods (E). Our primary diagnostic is the efficiency of convective heat transfer (Nu). In general, we find that the convective behavior of liquid metal differs substantially from that of moderate Pr fluids, such as water. In particular, a transition between rotationally constrained and weakly rotating turbulent states is identified, and this transition differs substantially from that observed in moderate Pr fluids. This difference, we hypothesize, may explain the different classes of magnetic fields observed on the Gas and Ice Giant planets, whose dynamo regions consist of Pr 1 fluids, respectively.

  9. Numerical study on turbulent forced convective heat transfer using nanofluids TiO2 in an automotive cooling system

    Directory of Open Access Journals (Sweden)

    Adnan M. Hussein

    2017-03-01

    Full Text Available The limited thermal properties of liquids have led to the addition of solid nanoparticles to liquids in many industrial applications. In this paper, the friction factor and forced convection heat transfer of TiO2 nanoparticles dispersed in water in a car radiator was numerically determined. Four different nanofluid volume concentrations (1%, 2%, 3% and 4% were used, and the resulting thermal properties were evaluated. The Reynolds number and inlet temperature ranged from 10000 to 100000 and from 60 to 90 °C, respectively. The results showed that the friction factor decreases as the Reynolds number increases and increases as the volume concentration increases. Additionally, the Nusselt number increases as the Reynolds number and volume concentration of the nanofluid increases. The TiO2 nanofluid at low concentrations can enhance the heat transfer efficiency up to 20% compared with that of pure water. There was good agreement among the CFD analysis and experimental data available in the literature.

  10. Probability distribution functions in turbulent convection

    Science.gov (United States)

    Balachandar, S.; Sirovich, L.

    1991-01-01

    Results of an extensive investigation of probability distribution functions (pdf's) for Rayleigh-Benard convection, in the hard turbulence regime, are presented. It is seen that the pdf's exhibit a high degree of internal universality. In certain cases this universality is established within two Kolmogorov scales of a boundary. A discussion of the factors leading to universality is presented.

  11. Electromagnetic enhancement of turbulent heat transfer

    NARCIS (Netherlands)

    Kenjeres, S.

    2008-01-01

    We performed large eddy simulations (LES) of the turbulent natural convection of an electrically conductive fluid (water with 7% Na2SO4 electrolyte solution) in a moderate (4:4:1) aspect ratio enclosure heated from below and cooled from above and subjected to external nonuniformly distributed

  12. Confinement and dynamical regulation in two-dimensional convective turbulence

    DEFF Research Database (Denmark)

    Bian, N.H.; Garcia, O.E.

    2003-01-01

    In this work the nature of confinement improvement implied by the self-consistent generation of mean flows in two-dimensional convective turbulence is studied. The confinement variations are linked to two distinct regulation mechanisms which are also shown to be at the origin of low......-frequency bursting in the fluctuation level and the convective heat flux integral, both resulting in a state of large-scale intermittency. The first one involves the control of convective transport by sheared mean flows. This regulation relies on the conservative transfer of kinetic energy from tilted fluctuations...... to the mean component of the flow. Bursting can also result from the quasi-linear modification of the linear instability drive which is the mean pressure gradient. For each bursting process the relevant zero-dimensional model equations are given. These are finally coupled in a minimal model of convection...

  13. Infrasound generation by turbulent convection

    OpenAIRE

    Akhalkatsi, M.; Gogoberidze, G.; Morrison, P. J.

    2004-01-01

    Low frequency acoustic wave generation is studied taking into account the effect of stratification, inhomogeneity of background velocity profile and temperature fluctuations. It is shown that for the typical parameters of convective storms the dipole radiation related to temperature inhomogeneities is at least of the same order as radiation of Lighthill's quadrupole source. It is also shown that the source related to stratification could have valuable contribution whereas some other sources a...

  14. Direct numerical simulation and statistical analysis of turbulent convection in lead-bismuth

    Energy Technology Data Exchange (ETDEWEB)

    Otic, I.; Grotzbach, G. [Forschungszentrum Karlsruhe GmbH, Institut fuer Kern-und Energietechnik (Germany)

    2003-07-01

    Improved turbulent heat flux models are required to develop and analyze the reactor concept of an lead-bismuth cooled Accelerator-Driven-System. Because of specific properties of many liquid metals we have still no sensors for accurate measurements of the high frequency velocity fluctuations. So, the development of the turbulent heat transfer models which are required in our CFD (computational fluid dynamics) tools needs also data from direct numerical simulations of turbulent flows. We use new simulation results for the model problem of Rayleigh-Benard convection to show some peculiarities of the turbulent natural convection in lead-bismuth (Pr = 0.025). Simulations for this flow at sufficiently large turbulence levels became only recently feasible because this flow requires the resolution of very small velocity scales with the need for recording long-wave structures for the slow changes in the convective temperature field. The results are analyzed regarding the principle convection and heat transfer features. They are also used to perform statistical analysis to show that the currently available modeling is indeed not adequate for these fluids. Basing on the knowledge of the details of the statistical features of turbulence in this convection type and using the two-point correlation technique, a proposal for an improved statistical turbulence model is developed which is expected to account better for the peculiarities of the heat transfer in the turbulent convection in low Prandtl number fluids. (authors)

  15. CONVECTIVE HEAT AND MASS TRANSFER IN THE COMBUSTION OF CHEMICALLY ACTIVE SUBSTANCES IN THE BOUNDARY LAYER ON A POROUS SURFACE.

    Science.gov (United States)

    COOLING, *POROUS MATERIALS), (*HEAT TRANSFER, *COMBUSTION), (* MASS TRANSFER , COMBUSTION), CONVECTION(HEAT TRANSFER), GAS FLOW, INJECTION, CHEMICAL REACTIONS, LAMINAR BOUNDARY LAYER, TURBULENT BOUNDARY LAYER, THERMAL INSULATION, USSR

  16. Turbulent resistive heating of solar coronal arches

    Science.gov (United States)

    Benford, G.

    1983-01-01

    The possibility that coronal heating occurs by means of anomalous Joule heating by electrostatic ion cyclotron waves is examined, with consideration given to currents running from foot of a loop to the other. It is assumed that self-fields generated by the currents are absent and currents follow the direction of the magnetic field, allowing the plasma cylinder to expand radially. Ion and electron heating rates are defined within the cylinder, together with longitudinal conduction and convection, radiation and cross-field transport, all in terms of Coulomb and turbulent effects. The dominant force is identified as electrostatic ion cyclotron instability, while ion acoustic modes remain stable. Rapid heating from an initial temperature of 10 eV to 100-1000 eV levels is calculated, with plasma reaching and maintaining a temperature in the 100 eV range. Strong heating is also possible according to the turbulent Ohm's law and by resistive heating.

  17. Phenomenological Nusselt-Rayleigh Scaling of Turbulent Thermal Convection

    Science.gov (United States)

    Liu, Chien-Chia

    2017-12-01

    Natural convection between the hot floor and the cool ceiling, so called Rayleigh-Bénard convection, is pervasive and of both fundamental and industrial interests. One key issue is how heat transfer varies with increasing thermal potential, or equivalently how the Nusselt number (Nu) scales with the Rayleigh number (Ra). The overview of experimental findings remains to show the need of extra explanation complemental to the current theories. Here we present a model based on the phenomenological theory of turbulence, where the power-law spectral exponent of the energy spectrum is the only input parameter required. The goal aims to elucidate the unexplained aspect in the Nu-Ra scaling. We find that Kolmogorov turbulence in the current model leads to Nu ˜ Ra0.3, in good agreement with the modern experimental results. We hope that this model could stimulate the discussion as to the effects of the spectral phenomena on the Nu-Ra scaling, and thus augment our understanding of buoyancy-driven thermal convection.

  18. Direct numerical simulation of low-Prandtl number turbulent convection above a wavy wall

    Energy Technology Data Exchange (ETDEWEB)

    Errico, Orsola; Stalio, Enrico, E-mail: enrico.stalio@unimore.it

    2015-08-15

    Highlights: • Turbulent convection is investigated in a wavy channel for Re = 18, 880 and Pr = 0.025. • In the considered Péclet number range, heat transfer is mostly by mean flow advection. • The Generalized Gradient Diffusion Hypothesis (GGDH) represents with fair accuracy the direction of turbulent heat fluxes. • Given the time scale in the model depends on mechanical quantities only, C{sub θ} needs to be tuned for Pr ≠ 1. - Abstract: Turbulent forced convection is investigated by Direct Numerical Simulation in a channel with one sinusoidal wavy wall and one flat wall. Fluid flow and heat transfer are periodically fully developed, the simulated Reynolds number of the bulk velocity and the hydraulic diameter is Re = 18, 880 while three Prandtl numbers are considered, i.e. Pr = 0.025, Pr = 0.2, and Pr = 0.71. The fluid flow is characterized by separation, reattachment and a shear layer downstream the wave peak, these are conditions relevant for turbulent heat transfer and passive scalar transport applications. In the range of Péclet numbers investigated, the most important heat transfer mechanism is by mean flow advection. Accordingly, the peak heat transfer region is in the upslope part of the domain. The separation bubble instead acts as a barrier to convection and the heat transfer rate is minimum close to separation. An a priori analysis is performed in order to assess the accuracy of turbulent heat transfer models based on the Generalized Gradient Diffusion Hypothesis.

  19. Turbulent thermal convection over rough surfaces

    Science.gov (United States)

    Stringano, G.; Verzicco, R.; Pascazio, G.

    2005-05-01

    Convective heat transport has important applications in engineering and meteorology and a better understanding of heat transport phenomena would lead to improvements in technological applications such as cooling of thermal machines and micro-electronic components or cooling during a metallurgical fusion. It would also improve the prediction of geophysical motions in oceans and atmosphere. The use of rough surfaces is a way to enhance the heat flux. The interaction between the main shear flow and the rough surface creates secondary vortices that enhance the detachment of thermal plumes from the tip of the rough elements. In this work numerical simulations are conducted in a cylindrical cell heated from below and cooled from above in presence of rough surfaces. A comparison of Rayleigh versus Nusselt number scaling between rough surfaces and smooth ones shows enhanced heat fluxes. The flow is solved using a direct numerical simulation (DNS) of the three dimensional unsteady Navier Stokes equations with the Boussinesq approximation and an immersed boundary approach is used for the treatment of rough surfaces.

  20. Convective Induced Turbulence (CIT) Detection via Total Lightning Sensing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We proposes to build a prototype Convective-Induced Turbulence (CIT) hazard detection system based on total lightning sensing as an indicator of the location and...

  1. Double tube heat exchanger with novel enhancement: part II—single phase convective heat transfer

    Science.gov (United States)

    Tiruselvam, R.; Chin, W. M.; Raghavan, Vijay R.

    2012-08-01

    The study is conducted to evaluate the heat transfer characteristics of two new and versatile enhancement configurations in a double tube heat exchanger annulus. The novelty is that they are usable in single phase forced convection, evaporation and condensation. Heat transfer coefficients are determined by the Wilson Plot technique in laminar and turbulent flow and correlations are proposed for Nusselt numbers. Comparisons are then made between heat transfer and flow friction.

  2. Kinetic thermal structure in turbulent Rayleigh-Bénard convection

    Science.gov (United States)

    Chen, Jun; Yin, Ze-Xia; She, Zhen-Su; Bao, Yun

    2017-11-01

    Plumes are believed to be the most important heat carrier in turbulent Rayleigh-Bénard convection (RBC). However, a physically sound and clear definition of plume is still absent. We report here the investigation of a definition of plume called kinetic thermal structure (KTS), based on the analysis of vertical velocity gradient (Λ = ∂w / ∂z), using direct numerical simulation (DNS) data of the three-dimensional RBC in a rectangular cell for Pr = 0.7 and Ra = 1 ×108 5 ×109 . It is shown that the conditional average of temperature on Λ exhibits such a behavior that when Λ is larger than a threshold, the volume carries a constant temperature of fluid, hence defines an unambiguous thermal structure, KTS. The DNS show that the KTS behaves in a sheet-like shape near the conducting plate, and becomes slender and smaller with increasing Ra . The heat flux carried by KTS displays a scaling law, with an exponent larger than the global- Nu - Ra scaling, indicating stronger heat transport than the turbulent background. An advantage of the KTS is its connection to the balance equation allowing, for the first time, a prediction of the Ra -dependence of its vertical velocity and the characteristic Λ threshold, validated by DNS. Supported by NSFC (11172006, 11221062, 11452002), and by MOST (China) 973 project (2009CB724100).

  3. Internally heated convection and Rayleigh-Bénard convection

    CERN Document Server

    Goluskin, David

    2016-01-01

    This Brief describes six basic models of buoyancy-driven convection in a fluid layer: three configurations of internally heated convection and three configurations of Rayleigh-Bénard convection. The author discusses the main quantities that characterize heat transport in each model, along with the constraints on these quantities. This presentation is the first to place the various models in a unified framework, and similarities and differences between the cases are highlighted. Necessary and sufficient conditions for convective motion are given. For the internally heated cases only, parameter-dependent lower bounds on the mean fluid temperature are proven, and results of past simulations and laboratory experiments are summarized and reanalyzed. The author poses several open questions for future study.

  4. Surface Temperature and Surface-Layer Turbulence in a Convective Boundary Layer

    NARCIS (Netherlands)

    Garai, A.; Pardyjak, E.; Steeneveld, G.J.; Kleissl, J.

    2013-01-01

    Previous laboratory and atmospheric experiments have shown that turbulence influences the surface temperature in a convective boundary layer. The main objective of this study is to examine land-atmosphere coupled heat transport mechanism for different stability conditions. High frequency infrared

  5. About the possible options for models of convective heat transfer in closed volumes with local heating source

    OpenAIRE

    Maksimov Vyacheslav I.; Nagornova Tatiana A.; Shestakov Igor A.

    2015-01-01

    Results of mathematical modeling of convective heat transfer in air area surrounded on all sides enclosing structures, in the presence of heat source at the lower boundary of the media are presented. Solved the system of differential equations of unsteady Navier-Stokes equations with the appropriate initial and boundary conditions. The process of convective heat transfer is calculated using the models of turbulence Prandtl and Prandtl-Reichard. Takes into account the processes of heat exchang...

  6. Global and local statistics in turbulent convection at low Prandtl numbers

    CERN Document Server

    Scheel, Janet D

    2016-01-01

    Statistical properties of turbulent Rayleigh-Benard convection at low Prandtl numbers (Pr), which are typical for liquid metals such as mercury, gallium or liquid sodium, are investigated in high-resolution three-dimensional spectral element simulations in a closed cylindrical cell with an aspect ratio of one and are compared to previous turbulent convection simulations in air. We compare the scaling of global momentum and heat transfer. The scaling exponents are found to be in agreement with experiments. Mean profiles of the root-mean-square velocity as well as the thermal and kinetic energy dissipation rates have growing amplitudes with decreasing Prandtl number which underlies a more vigorous bulk turbulence in the low-Pr regime. The skin-friction coefficient displays a Reynolds-number dependence that is close to that of an isothermal, intermittently turbulent velocity boundary layer. The thermal boundary layer thicknesses are larger as Pr decreases and conversely the velocity boundary layer thicknesses be...

  7. Thermal turbulent convection: thermal plumes and fluctuations; Convection thermique turbulente: panaches et fluctuations

    Energy Technology Data Exchange (ETDEWEB)

    Gibert, M

    2007-10-15

    In this study we investigate the phenomenon of thermal turbulent convection in new and unprecedented ways. The first system we studied experimentally is an infinite vertical channel, where a constant vertical mean gradient of temperature exists. Inside this channel the average mass flux is null. The results obtained from our measurements reveal that the flow is mainly inertial; indeed the dissipative coefficients (here the viscosity) play a role only to define a coherence length L. This length is the distance over which the thermal plumes can be considered as 'free falling' objects. The horizontal transport, of heat and momentum, is entirely due to fluctuations. The associated 'mixing length' is small compared to the channel width. In the other hand, the vertical heat transport is due to coherent structures: the heat plumes. Those objects were also investigated in a Lagrangian study of the flow in the bulk of a Rayleigh-Benard cell. The probe, which has the same density as the fluid used in this experiment, is a sphere of 2 cm in diameter with embarked thermometers and radio-emitter. The heat plumes transport it, which allows a statistical study of such objects. (author)

  8. Natural convection heat transfer along vertical rectangular ducts

    Energy Technology Data Exchange (ETDEWEB)

    Ali, M. [King Saud University, Mechanical Engineering Department, Riyadh (Saudi Arabia)

    2009-12-15

    Experimental investigations have been reported on steady state natural convection from the outer surface of vertical rectangular and square ducts in air. Seven ducts have been used; three of them have a rectangular cross section and the rest have square cross section. The ducts are heated using internal constant heat flux heating elements. The temperatures along the vertical surface and the peripheral directions of the duct wall are measured. Axial (perimeter averaged) heat transfer coefficients along the side of each duct are obtained for laminar and transition to turbulent regimes of natural convection heat transfer. Axial (perimeter averaged) Nusselt numbers are evaluated and correlated using the modified Rayleigh numbers for laminar and transition regime using the vertical axial distance as a characteristic length. Critical values of the modified Rayleigh numbers are obtained for transition to turbulent. Furthermore, total overall averaged Nusselt numbers are correlated with the modified Rayleigh numbers and the area ratio for the laminar regimes. The local axial (perimeter averaged) heat transfer coefficients are observed to decrease in the laminar region and increase in the transition region. Laminar regimes are obtained at the lower half of the ducts and its chance to appear decreases as the heat flux increases. (orig.)

  9. Effects of polymer additives in the bulk of turbulent thermal convection

    CERN Document Server

    Xie, Yi-Chao; Funfschilling, Denis; Li, Xiao-Ming; Ni, Rui; Xia, Ke-Qing

    2015-01-01

    We present experimental evidence that a minute amount of polymer additives can significantly enhance heat transport in the bulk region of turbulent thermal convection. The effects of polymer additives are found to be the \\textit{suppression} of turbulent background fluctuations that give rise to incoherent heat fluxes that make no net contribution to heat transport, and at the same time to \\textit{increase} the coherency of temperature and velocity fields. The suppression of small-scale turbulent fluctuations leads to more coherent thermal plumes that result in the heat transport enhancement. The fact that polymer additives can increase the coherency of thermal plumes is supported by the measurements of a number of local quantities, such as the extracted plume amplitude and width, the velocity autocorrelation functions and the velocity-temperature cross-correlation coefficient. The results from local measurements also suggest the existence of a threshold value for the polymer concentration, only above which c...

  10. Spectrally-consistent regularization modeling of turbulent natural convection flows

    NARCIS (Netherlands)

    Trias, F. Xavier; Verstappen, Roel; Gorobets, Andrey; Oliva, Assensi

    2012-01-01

    The incompressible Navier-Stokes equations constitute an excellent mathematical modelization of turbulence. Unfortunately, attempts at performing direct simulations are limited to relatively low-Reynolds numbers because of the almost numberless small scales produced by the non-linear convective

  11. Cubic Spline Collocation Method for the Simulation of Turbulent Thermal Convection in Compressible Fluids

    Energy Technology Data Exchange (ETDEWEB)

    Castillo, Victor Manuel [Univ. of California, Davis, CA (United States)

    1999-01-01

    A collocation method using cubic splines is developed and applied to simulate steady and time-dependent, including turbulent, thermally convecting flows for two-dimensional compressible fluids. The state variables and the fluxes of the conserved quantities are approximated by cubic splines in both space direction. This method is shown to be numerically conservative and to have a local truncation error proportional to the fourth power of the grid spacing. A ''dual-staggered'' Cartesian grid, where energy and momentum are updated on one grid and mass density on the other, is used to discretize the flux form of the compressible Navier-Stokes equations. Each grid-line is staggered so that the fluxes, in each direction, are calculated at the grid midpoints. This numerical method is validated by simulating thermally convecting flows, from steady to turbulent, reproducing known results. Once validated, the method is used to investigate many aspects of thermal convection with high numerical accuracy. Simulations demonstrate that multiple steady solutions can coexist at the same Rayleigh number for compressible convection. As a system is driven further from equilibrium, a drop in the time-averaged dimensionless heat flux (and the dimensionless internal entropy production rate) occurs at the transition from laminar-periodic to chaotic flow. This observation is consistent with experiments of real convecting fluids. Near this transition, both harmonic and chaotic solutions may exist for the same Rayleigh number. The chaotic flow loses phase-space information at a greater rate, while the periodic flow transports heat (produces entropy) more effectively. A linear sum of the dimensionless forms of these rates connects the two flow morphologies over the entire range for which they coexist. For simulations of systems with higher Rayleigh numbers, a scaling relation exists relating the dimensionless heat flux to the two-seventh's power of the Rayleigh number

  12. Infrared thermography for convective heat transfer measurements

    Energy Technology Data Exchange (ETDEWEB)

    Carlomagno, Giovanni Maria; Cardone, Gennaro [University of Naples Federico II, Department of Aerospace Engineering, Naples (Italy)

    2010-12-15

    This paper deals with the evolution of infrared (IR) thermography into a powerful optical tool that can be used in complex fluid flows to either evaluate wall convective heat fluxes or investigate the surface flow field behavior. Measurement of convective heat fluxes must be performed by means of a thermal sensor, where temperatures have to be measured with proper transducers. By correctly choosing the thermal sensor, IR thermography can be successfully exploited to resolve convective heat flux distributions with both steady and transient techniques. When comparing it to standard transducers, the IR camera appears very valuable because it is non-intrusive, it has a high sensitivity (down to 20 mK), it has a low response time (down to 20 {mu}s), it is fully two dimensional (from 80 k up to 1 M pixels, at 50 Hz) and, therefore, it allows for better evaluation of errors due to tangential conduction within the sensor. This paper analyses the capability of IR thermography to perform convective heat transfer measurements and surface visualizations in complex fluid flows. In particular, it includes the following: the necessary radiation theory background, a review of the main IR camera features, a description of the pertinent heat flux sensors, an analysis of the IR image processing methods and a report on some applications to complex fluid flows, ranging from natural convection to hypersonic regime. (orig.)

  13. Turbulent boundary layer in high Rayleigh number convection in air.

    Science.gov (United States)

    du Puits, Ronald; Li, Ling; Resagk, Christian; Thess, André; Willert, Christian

    2014-03-28

    Flow visualizations and particle image velocimetry measurements in the boundary layer of a Rayleigh-Bénard experiment are presented for the Rayleigh number Ra=1.4×1010. Our visualizations indicate that the appearance of the flow structures is similar to ordinary (isothermal) turbulent boundary layers. Our particle image velocimetry measurements show that vorticity with both positive and negative sign is generated and that the smallest flow structures are 1 order of magnitude smaller than the boundary layer thickness. Additional local measurements using laser Doppler velocimetry yield turbulence intensities up to I=0.4 as in turbulent atmospheric boundary layers. From our observations, we conclude that the convective boundary layer becomes turbulent locally and temporarily although its Reynolds number Re≈200 is considerably smaller than the value 420 underlying existing phenomenological theories. We think that, in turbulent Rayleigh-Bénard convection, the transition of the boundary layer towards turbulence depends on subtle details of the flow field and is therefore not universal.

  14. Electromagnetically driven dwarf tornados in turbulent convection

    NARCIS (Netherlands)

    Kenjeres, S.

    2011-01-01

    Motivated by the concept of interdependency of turbulent flow and electromagnetic fields inside the spiraling galaxies, we explored the possibilities of generating a localized Lorentz force that will produce a three-dimensional swirling flow in weakly conductive fluids. Multiple vortical flow

  15. Convective heat transfer in non-uniformly heated corrugated slots

    Science.gov (United States)

    Abtahi, Arman; Floryan, J. M.

    2017-10-01

    An analysis of heat transfer in non-uniformly heated corrugated slots has been carried out. A sinusoidal corrugation is placed at the lower plate that is exposed to heating consisting of uniform and sinusoidal components, while the upper smooth plate is kept isothermal. The phase difference ΩTL describes the shift between the heating and geometric non-uniformities. The analysis is limited to heating conditions that do not give rise to secondary motions. Depending on ΩTL, the conductive heat flow is directed either upwards, or downwards, or is eliminated. Its magnitude is smallest for the long-wavelength systems and largest for the short-wavelength systems, and it increases proportionally to the corrugation amplitude and heating intensity. The same heating creates horizontal temperature gradients that give rise to convection whose form depends on ΩTL. Convection consists of counter-rotating rolls with the size dictated by the system wavelength when the hot spots (points of maximum temperature) overlap either with the corrugation tips or with the corrugation bottoms. Thermal drift forms for all other values of ΩTL. The convective heat flow is always directed upwards, and it is the largest in systems with wavelengths comparable to the slot height. The magnitude of the overall heat flow increases proportionally to the heating intensity when conductive effects dominate and proportionally to the second power of the heating intensity when convection dominates. It also increases proportionally to the corrugation amplitude. The system characteristics are dictated by convection when the relative position of the heating and corrugation patterns eliminates conduction. Addition of the uniform heating component amplifies the above processes, while uniform cooling reduces them. The processes described above are qualitatively similar for all Prandtl numbers of practical interest with the magnitude of the convective heat flow increasing with Pr.

  16. About the possible options for models of convective heat transfer in closed volumes with local heating source

    Directory of Open Access Journals (Sweden)

    Maksimov Vyacheslav I.

    2015-01-01

    Full Text Available Results of mathematical modeling of convective heat transfer in air area surrounded on all sides enclosing structures, in the presence of heat source at the lower boundary of the media are presented. Solved the system of differential equations of unsteady Navier-Stokes equations with the appropriate initial and boundary conditions. The process of convective heat transfer is calculated using the models of turbulence Prandtl and Prandtl-Reichard. Takes into account the processes of heat exchange region considered with the environment. Is carried out the analysis of the dimensionless heat transfer coefficient at interfaces “air – enclosures”. The distributions average along the gas temperature range are obtained.

  17. Convective heat transfer enhancement with nanofluids

    Science.gov (United States)

    Rahman, Md. Habibur; Abedin, Z.

    2017-12-01

    Nanofluids are considered to offer important advantages over conventional heat transfer fluids. Over a decade ago, researchers focused on measuring and modeling the effective thermal conductivity and viscosity of nanofluids. Recently important theoretical and experimental research works on convective heat transfer appeared in the open literatures on the enhancement of heat transfer using suspensions of nanometer-sized solid particle materials, metallic or nonmetallic in base heat transfer fluids. The purpose of this article is to summarize recent research on fluid flow and heat transfer enhancement characteristics of nanofluids and thereby identify opportunities for future research.

  18. Single phase channel flow forced convection heat transfer

    Energy Technology Data Exchange (ETDEWEB)

    Hartnett, J.P.

    1999-04-01

    A review of the current knowledge of single phase forced convection channel flow of liquids (Pr > 5) is presented. Two basic channel geometries are considered, the circular tube and the rectangular duct. Both laminar flow and turbulent flow are covered. The review begins with a brief overview of the heat transfer behavior of Newtonian fluids followed by a more detailed presentation of the behavior of purely viscous and viscoelastic Non-Newtonian fluids. Recent developments dealing with aqueous solutions of high molecular weight polymers and aqueous solutions of surfactants are discussed. The review concludes by citing a number of challenging research opportunities.

  19. Free convection film flows and heat transfer

    CERN Document Server

    Shang, Deyi

    2010-01-01

    Presents development of systematic studies for hydrodynamics and heat and mass transfer in laminar free convection, accelerating film boiling and condensation of Newtonian fluids, and accelerating film flow of non-Newtonian power-law fluids. This book provides a system of analysis models with a developed velocity component method.

  20. Solar Hot Water Heating by Natural Convection.

    Science.gov (United States)

    Noble, Richard D.

    1983-01-01

    Presents an undergraduate laboratory experiment in which a solar collector is used to heat water for domestic use. The working fluid is moved by natural convection so no pumps are required. Experimental apparatus is simple in design and operation so that data can be collected quickly and easily. (Author/JN)

  1. Determination of the convective heat transfer coefficient

    NARCIS (Netherlands)

    Spierings, D.; Bosman, F.; Peters, T.; Plasschaert, F.

    The value of the convective heat transfer coefficient (htc) is determined under different loading conditions by using a computer aided method. The thermal load has been applied mathematically as well as experimentally to the coronal surface of an axisymmetric tooth model. To verify the assumptions

  2. Forced Convection Heat Transfer in Circular Pipes

    Science.gov (United States)

    Tosun, Ismail

    2007-01-01

    One of the pitfalls of engineering education is to lose the physical insight of the problem while tackling the mathematical part. Forced convection heat transfer (the Graetz-Nusselt problem) certainly falls into this category. The equation of energy together with the equation of motion leads to a partial differential equation subject to various…

  3. Boiling turbulent Rayleigh-Bénard convection

    NARCIS (Netherlands)

    Lakkaraju, R.

    2013-01-01

    A fundamental understanding of liquid-vapor phase transitions, mainly boiling phenomenon, is essential due to its omnipresence in science and technology. In industries, many empirical correlations exist on the heat transport to get an optimized and efficient thermal design of the boiling equipment.

  4. Heat Flux Sensors for Infrared Thermography in Convective Heat Transfer

    Science.gov (United States)

    Carlomagno, Giovanni Maria; de Luca, Luigi; Cardone, Gennaro; Astarita, Tommaso

    2014-01-01

    This paper reviews the most dependable heat flux sensors, which can be used with InfraRed (IR) thermography to measure convective heat transfer coefficient distributions, and some of their applications performed by the authors' research group at the University of Naples Federico II. After recalling the basic principles that make IR thermography work, the various heat flux sensors to be used with it are presented and discussed, describing their capability to investigate complex thermo-fluid-dynamic flows. Several applications to streams, which range from natural convection to hypersonic flows, are also described. PMID:25386758

  5. Heat flux sensors for infrared thermography in convective heat transfer.

    Science.gov (United States)

    Carlomagno, Giovanni Maria; de Luca, Luigi; Cardone, Gennaro; Astarita, Tommaso

    2014-11-07

    This paper reviews the most dependable heat flux sensors, which can be used with InfraRed (IR) thermography to measure convective heat transfer coefficient distributions, and some of their applications performed by the authors' research group at the University of Naples Federico II. After recalling the basic principles that make IR thermography work, the various heat flux sensors to be used with it are presented and discussed, describing their capability to investigate complex thermo-fluid-dynamic flows. Several applications to streams, which range from natural convection to hypersonic flows, are also described.

  6. Heat Flux Sensors for Infrared Thermography in Convective Heat Transfer

    Directory of Open Access Journals (Sweden)

    Giovanni Maria Carlomagno

    2014-11-01

    Full Text Available This paper reviews the most dependable heat flux sensors, which can be used with InfraRed (IR thermography to measure convective heat transfer coefficient distributions, and some of their applications performed by the authors’ research group at the University of Naples Federico II. After recalling the basic principles that make IR thermography work, the various heat flux sensors to be used with it are presented and discussed, describing their capability to investigate complex thermo-fluid-dynamic flows. Several applications to streams, which range from natural convection to hypersonic flows, are also described.

  7. Experimental and Numerical Studies of Mechanically- and Convectively-Driven Turbulence in Planetary Interiors

    Science.gov (United States)

    Grannan, Alexander Michael

    2017-08-01

    characteristics of the resulting turbulence are investigated using meridional views to identify the dominate modes and spatial location of the turbulence. For the first time, measurements of the velocity in the equatorial plane are coupled with high resolution numerical simulations of the full flow field in identical geometry to characterize the instability mechanism, energy deposited into the fluid layer, and long-term evolution of the flow. The velocities determined through laboratory and numerical simulations when extrapolated to planets allow me to argue that the dynamics of mechanical forcing in low viscosity fluids may an important role as new and potentially large source of dissipation in planetary interiors. To study convective forcing, I have modified and performed a set of rotating and non-rotating hydrodynamic convection experiments using water as well as rotating and non-rotating magnetohydrodynamic convection in gallium. These studies are performed in a cylindrical geometry representing a model of high latitude planetary core style convection wherein the axis of rotation and gravity are aligned. For the studies using water, the steady columns that are characteristic of rotating convection and present in the dynamo models are likely to destabilize at the more extreme planetary parameters giving way to transitions to more complex styles of rotating turbulent flow. In the studies of liquid metal where the viscosity is lower, the onset of rotating convection occurs through oscillatory columnar convection well below the onset of steady columns. Such oscillatory modes are not represented at the parameters used by current dynamo models. Furthermore a suite of laboratory experiments shows that the imposition of rotational forces and magnetic forces both separately and together generate zeroeth order flow transitions that change the fundamental convective modes and heat transfer. Such regimes are more easily accessible to laboratory experiments then to numerical simulations

  8. Turbulent energy losses during orchard heating

    Energy Technology Data Exchange (ETDEWEB)

    Bland, W.L.

    1979-01-01

    Two rapid-response drag anemometers and low time constant thermocouples, all at 4 m above a heated orchard floor, sampled wind component in the vertical direction and temperature at 30 Hz. The turbulent heat flux calculated revealed not more than 10% of the heat lost from the orchard was via turbulent transort. The observations failed to support previous estimates that at least a third of the energy applied was lost through turbulent transport. Underestimation of heat loss due to mean flow and a newly revealed flux due to spatial variations in the mean flow may explain the unaccounted for loss.

  9. Analysis of subgrid models of heat convection by symmetry group theory

    Science.gov (United States)

    Razafindralandy, Dina; Hamdouni, Aziz

    2007-04-01

    Symmetries, i.e. transformations which leave the set of the solutions of the Navier-Stokes equations unchanged, play an important role in turbulence (conservation laws, wall laws, …). They should not be destroyed by turbulence models. The symmetries of the heat convection equations are then presented, for a non-isothermal fluid. Next, common subgrid stress tensor and flux models are analyzed, using the symmetry approach. To cite this article: D. Razafindralandy, A. Hamdouni, C. R. Mecanique 335 (2007).

  10. Turbulent Heat Transfer Behavior of Nanofluid in a Circular Tube Heated under Constant Heat Flux

    Directory of Open Access Journals (Sweden)

    Shuichi Torii

    2010-01-01

    Full Text Available The aim of the present study is to disclose the forced convective heat transport phenomenon of nanofluids inside a horizontal circular tube subject to a constant and uniform heat flux at the wall. Consideration is given to the effect of the inclusion of nanoparticles on heat transfer enhancement, thermal conductivity, viscosity, and pressure loss in the turbulent flow region. It is found that (i heat transfer enhancement is caused by suspending nanoparticles and becomes more pronounced with the increase of the particle volume fraction, (ii its augmentation is affected by three different nanofluids employed here, and (iii the presence of particles produces adverse effects on viscosity and pressure loss that also increases with the particle volume fraction.

  11. Convective heat transfer in porous media

    Science.gov (United States)

    Cheng, P.

    Recent emerging technologies on the extraction of geothermal energy, the design of insulation systems for energy conservation, the use of aquifers for hot-water storage, the disposal of nuclear wastes in sub-seabeds, the enhanced recovery of oils by thermal methods, and the design of catalyst-bed reactors have demanded an improved understanding of heat transfer mechanisms in fluid-filled porous media. Experiments have been conducted to investigate the onset of free convection in rectangular and cylindrical enclosures filled with porous media and heated from below. The Nusselt numbers determined from these experiments during steady conditions are correlated in terms of the Rayleigh number. The data for free convection in rectangular geometries show considerable scattering among investigators using different porous media and fluids. Recently, some data has been obtained for free convect on in water-filled glass beads adjacent to a heated vertical flat plate, a horizontal cylinder and between vertical concentric cylinders. The data obtained at low Rayleigh numbers is found to be in good agreement with theoretical predictions based on Darcy's law.

  12. CFD study of forced convective heat transfer enhancement in a 90 ...

    Indian Academy of Sciences (India)

    In this paper, the forced convective heat transfer enhancement with nanofluids in a 90° pipe bend has been presented. Numerical investigation is carried out for the turbulent flow through the pipe employing finite volume method. The governing differential equations are discretized using hexahedral cells, and theresulting ...

  13. Turbulent collision-coalescence in maritime shallow convection

    Directory of Open Access Journals (Sweden)

    A. A. Wyszogrodzki

    2013-08-01

    Full Text Available This paper discusses cloud simulations aiming at quantitative assessment of the effects of cloud turbulence on rain development in shallow ice-free convective clouds. Cloud fields from large-eddy simulations (LES applying bin microphysics with the collection kernel enhanced by cloud turbulence are compared to those with the standard gravitational collection kernel. Simulations for a range of cloud condensation nuclei (CCN concentrations are contrasted. Details on how the parameterized turbulent collection kernel is used in LES simulations are presented. Because of the disparity in spatial scales between the bottom-up numerical studies guiding the turbulent kernel development and the top-down LES simulations of cloud dynamics, we address the consequence of the turbulence intermittency in the unresolved range of scales on the mean collection kernel applied in LES. We show that intermittency effects are unlikely to play an important role in the current simulations. Highly-idealized single-cloud simulations are used to illustrate two mechanisms that operate in cloud field simulations. First, the microphysical enhancement leads to earlier formation of drizzle through faster autoconversion of cloud water into drizzle, as suggested by previous studies. Second, more efficient removal of condensed water from cloudy volumes when a turbulent collection kernel is used leads to an increased cloud buoyancy and enables clouds to reach higher levels. This is the dynamical enhancement. Both mechanisms operate in the cloud field simulations. The microphysical enhancement leads to the increased drizzle and rain inside clouds in simulations with high CCN. In low-CCN simulations with significant surface rainfall, dynamical enhancement leads to a larger contribution of deeper clouds to the entire cloud population, and results in a dramatically increased mean surface rain accumulation. These results call for future modeling and observational studies to corroborate the

  14. Measurements of Turbulent Convection Speeds in Multistream Jets Using Time-Resolved PIV

    Science.gov (United States)

    Bridges, James; Wernet, Mark P.

    2017-01-01

    Convection speeds of turbulent velocities in jets, including multi-stream jets with and without flight stream, were measured using an innovative application of time-resolved particle image velocimetry. The paper describes the unique instrumentation and data analysis that allows the measurement to be made. Extensive data is shown that relates convection speed, mean velocity, and turbulent velocities for multiple jet cases. These data support the overall observation that the local turbulent convection speed is roughly that of the local mean velocity, biased by the relative intensity of turbulence.

  15. Measurements of Turbulence Convection Speeds in Multistream Jets Using Time-Resolved PIV

    Science.gov (United States)

    Bridges, James; Wernet, Mark P.

    2017-01-01

    Convection speeds of turbulent velocities in jets, including multi-stream jets with and without flight stream, were measured using an innovative application of time-resolved particle image velocimetry. The paper describes the unique instrumentation and data analysis that allows the measurement to be made. Extensive data is shown that relates convection speed, mean velocity, and turbulent velocities for multiple jet cases. These data support the overall observation that the local turbulent convection speed is roughly that of the local mean velocity, biased by the relative intensity of turbulence.

  16. Conjugate Problems in Convective Heat Transfer: Review

    Directory of Open Access Journals (Sweden)

    Abram Dorfman

    2009-01-01

    Full Text Available A review of conjugate convective heat transfer problems solved during the early and current time of development of this modern approach is presented. The discussion is based on analytical solutions of selected typical relatively simple conjugate problems including steady-state and transient processes, thermal material treatment, and heat and mass transfer in drying. This brief survey is accompanied by the list of almost two hundred publications considering application of different more and less complex analytical and numerical conjugate models for simulating technology processes and industrial devices from aerospace systems to food production. The references are combined in the groups of works studying similar problems so that each of the groups corresponds to one of selected analytical solutions considered in detail. Such structure of review gives the reader the understanding of early and current situation in conjugate convective heat transfer modeling and makes possible to use the information presented as an introduction to this area on the one hand, and to find more complicated publications of interest on the other hand.

  17. Fast Prediction Method for Steady-State Heat Convection

    KAUST Repository

    Wáng, Yì

    2012-03-14

    A reduced model by proper orthogonal decomposition (POD) and Galerkin projection methods for steady-state heat convection is established on a nonuniform grid. It was verified by thousands of examples that the results are in good agreement with the results obtained from the finite volume method. This model can also predict the cases where model parameters far exceed the sample scope. Moreover, the calculation time needed by the model is much shorter than that needed for the finite volume method. Thus, the nonuniform POD-Galerkin projection method exhibits high accuracy, good suitability, and fast computation. It has universal significance for accurate and fast prediction. Also, the methodology can be applied to more complex modeling in chemical engineering and technology, such as reaction and turbulence. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. BROWNIAN HEAT TRANSFER ENHANCEMENT IN THE TURBULENT REGIME

    Directory of Open Access Journals (Sweden)

    Suresh Chandrasekhar

    2016-08-01

    Full Text Available The paper presents convection heat transfer of a turbulent flow Al2O3/water nanofluid in a circular duct. The duct is a under constant and uniform heat flux. The paper computationally investigates the system’s thermal behavior in a wide range of Reynolds number and also volume concentration up to 6%. To obtain the nanofluid thermophysical properties, the Hamilton-Crosser model along with the Brownian motion effect are utilized. Then the thermal performance of the system with the nanofluid is compared to the conventional systems which use water as the working fluid. The results indicate that the use of nanofluid of 6% improves the heat transfer rate up to 36.8% with respect to pure water. Therefore, using the Al2O3/water nanofluid instead of water can be a great choice when better heat transfer is needed.

  19. Heat transport in the geostrophic regime of rotating Rayleigh-B{\\'e}nard convection

    CERN Document Server

    Ecke, Robert E

    2013-01-01

    We report experimental measurements of heat transport in rotating Rayleigh-B{\\'e}nard convection in a cylindrical convection cell with aspect ratio $\\Gamma = 1/2$. The fluid was helium gas with Prandtl number Pr = 0.7. The range of control parameters was Rayleigh number $4 \\times 10^9 < {\\rm Ra} < 4 \\times 10^{11}$ and Ekman number $2 \\times 10^{-7} < {\\rm Ek} < 3 \\times 10^{-5}$(corresponding to Taylor number $4 \\times 10^9 < {\\rm Ta} < 1 \\times 10^{14}$ and convective Rossby number $0.07 < {\\rm Ro} < 5$). We determine the crossover from weakly rotating turbulent convection to rotation dominated geostrophic convection through experimental measurements of the normalized heat transport Nu. The heat transport for the rotating state in the geostrophic regime, normalized by the zero-rotation heat transport, is consistent with scaling of $({\\rm RaEk}^{-7/4})^\\beta$ with $\\beta \\approx 1$. A phase diagram is presented that encapsulates measurements on the potential geostrophic turbulence reg...

  20. Visualization of Natural Convection Heat Transfer on a Single Sphere using the Electroplating System

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dong Young; Chung, Bum Jin [Kyunghee University, Yongin (Korea, Republic of)

    2016-05-15

    The natural convective flows on outer sphere rise along surface. At top of sphere, the flows are lifted-up plume shape. For laminar flows, the local heat transfer shows maximum at the bottom of sphere and a monotonic decreases as flows approached to the top. The laminar natural convection heat transfer on a single sphere has been studied experimentally and numerically by several researchers. However, relatively less study has been performed for turbulent flows as it requires large facilities to achieve high Rayleigh numbers. The flows, which occur transition, is hard to experiment because of unstable. This study tried measurement of heat transfer and visualization external natural convection on a single sphere. The basic idea is that the plating patterns of copper on the sphere in mass transfer system will reveal the amount of heat transfer according to angular distance from the bottom. This study simulated natural convection on a single sphere and performed a mass transfer experiment using heat and mass transfer analogy concept. For visualization experiment, streak form plating pattern was observed. In this case, it seems that turbulence sets on the top of sphere and increases local heat transfer.

  1. Numerical and experimental study of turbulent Rayleigh-Benard convection of water in a cubical cavity

    Energy Technology Data Exchange (ETDEWEB)

    Valencia, L.; Pallares, J.; Cuesta, I.; Grau, F.X. [University Rovira i Virgili, Dept. of Mechanical Engineering, Tarragona (Spain)

    2005-07-01

    Experimental measurements and numerical simulations of natural convection in a partially conducting cubical cavity heated from below and cooled from above are reported at turbulent Rayleigh numbers (Ra=10{sup 7} and Ra=7 x 10{sup 7}) and water as a convective fluid (Pr=6.0). The numerical simulations were carried out with a second order finite volume code without any turbulence model because the time-steps and grid sizes used are adequate for the time and spatial resolution requirements reported in previous direct numerical simulations of Rayleigh-Benard flows. The Boussinesq approximation was considered in the simulations according to the thermal conditions and the dimensions of the cavities used in the experiments. The Particle Image Velocimetry (PIV) technique was used to measure the two velocity components parallel to a vertical mid-plane of the cavity. If the heat conduction through the sidewalls is considered in the simulations, there is a general agreement between the predicted time averaged local velocities and those experimentally measured in the vertical mid-planes. (authors)

  2. Natural convection in a fluid layer periodically heated from above.

    Science.gov (United States)

    Hossain, M Z; Floryan, J M

    2014-08-01

    Natural convection in a horizontal layer subject to periodic heating from above has been studied. It is shown that the primary convection leads to the cooling of the bulk of the fluid below the mean temperature of the upper wall. The secondary convection may lead either to longitudinal rolls, transverse rolls, or oblique rolls. The global flow properties (e.g., the average Nusselt number for the primary convection and the critical conditions for the secondary convection) are identical to those of the layer heated from below. However, the flow and temperature patterns exhibit phase shifts in the horizontal directions.

  3. Transitions in turbulent rotating Rayleigh-B\\'enard convection

    CERN Document Server

    Schmitz, S

    2010-01-01

    Numerical simulations of rotating Rayleigh-B\\'enard convection are presented for both no slip and free slip boundaries. The goal is to find a criterion distinguishing convective flows dominated by the Coriolis force from those nearly unaffected by rotation. If one uses heat transport as an indicator of which regime the flow is in, one finds that the transition between the flow regimes always occurs at the same value of a certain combination of Reynolds, Prandtl and Ekman numbers for both boundary conditions. If on the other hand one uses the helicity of the velocity field to identify flows nearly independent of rotation, one finds the transition at a different location in parameter space.

  4. Assessment of CFD Hypersonic Turbulent Heating Rates for Space Shuttle Orbiter

    Science.gov (United States)

    Wood, William A.; Oliver, A. Brandon

    2011-01-01

    Turbulent CFD codes are assessed for the prediction of convective heat transfer rates at turbulent, hypersonic conditions. Algebraic turbulence models are used within the DPLR and LAURA CFD codes. The benchmark heat transfer rates are derived from thermocouple measurements of the Space Shuttle orbiter Discovery windward tiles during the STS-119 and STS-128 entries. The thermocouples were located underneath the reaction-cured glass coating on the thermal protection tiles. Boundary layer transition flight experiments conducted during both of those entries promoted turbulent flow at unusually high Mach numbers, with the present analysis considering Mach 10{15. Similar prior comparisons of CFD predictions directly to the flight temperature measurements were unsatisfactory, showing diverging trends between prediction and measurement for Mach numbers greater than 11. In the prior work, surface temperatures and convective heat transfer rates had been assumed to be in radiative equilibrium. The present work employs a one-dimensional time-accurate conduction analysis to relate measured temperatures to surface heat transfer rates, removing heat soak lag from the flight data, in order to better assess the predictive accuracy of the numerical models. The turbulent CFD shows good agreement for turbulent fuselage flow up to Mach 13. But on the wing in the wake of the boundary layer trip, the inclusion of tile conduction effects does not explain the prior observed discrepancy in trends between simulation and experiment; the flight heat transfer measurements are roughly constant over Mach 11-15, versus an increasing trend with Mach number from the CFD.

  5. Convective Heat Transfer in Acoustic Streaming Flows

    Science.gov (United States)

    Gopinath, Ashok

    1992-01-01

    Convective heat transfer due to acoustic streaming has been studied in the absence of an imposed mean flow. The work is motivated by the need to design and control the thermal features of a suitable experimental rig for the containerless processing of materials by heat treatment of acoustically levitated alloy samples at near zero-gravity. First the problem of heat transfer from an isolated sphere (in a standing sound field) is explored in detail. The streaming Reynolds number, Rs, which characterizes the resulting steady flows, is determined from the acoustic signal. A scale analysis is used to ascertain the importance of buoyancy and viscous dissipation. The steady velocity and temperature fields are determined using asymptotic techniques and numerical methods for the limiting cases of RsKundt tube (supporting a plane axial standing sound wave) with insulated side-wall and isothermal end-walls. Analytical solution techniques are used to determine the steady fields close to the tube walls. For the steady recirculatory transport in the core, the numerical solver PHOENICS is adopted for the solution of the complete elliptic form of the governing equations. A study of the effects of a range of acoustic and geometric parameters on the flow and heat transfer is performed and Nusselt number correlations are obtained for air. PHOENICS is also used to study the effects of variable fluid properties and axial side-wall conduction (coupled with radiation). The role of normal/reduced gravity is assessed and suggestions made for terrestrial testing of the levitation apparatus. Finally, with the sample located at a node in the levitation chamber, the effect of the interaction of the streaming flows (on the sphere and the tube walls) is estimated. Representative calculations for the sample heating/cooling rates are presented and compared with existing data in the literature.

  6. Validation Plan of Turbulence Models for Internal Gas Flow Analysis in a Heated Rectangular Riser Duct

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sin-Yeob; Shin, Dong-Ho; Park, Goon-Cherl; Cho, Hyoung Kyu [Seoul National Univ., Seoul (Korea, Republic of); Kim, Chan-Soo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    VHTR being developed at Korea Atomic Energy Research Institute adopts an air-cooled Reactor Cavity Cooling System (RCCS) incorporating rectangular riser channels to remove the afterheat emitted from the reactor vessel. Because the performance of RCCS is determined by heat removal rate through the RCCS riser, it is important to understand the heat transfer phenomena in the RCCS riser to ensure the safety of the reactor. In the mixed convection, due to the buoyance force induced by temperature and density differences, local flow structure and heat transfer mode near the heated wall have significantly dissimilar characteristics from both forced convection and free convection. In this study, benchmark calculation was conducted to reproduce the previous statements that V2F turbulence model can capture the mixed convection phenomena with the Shehata's experimental data. Then, the necessity of the model validation for the mixed convection phenomena was confirmed with the CFD analyses for the geometry of the prototype RCCS riser. For the purpose of validating the turbulence models for mixed convection phenomena in the heated rectangular riser duct, validation plan with three experimental tests was introduced. Among them, the flow visualization test facility with preserved cross-section geometry was introduced and a preliminary test result was shown.

  7. Heat transfer augmentation in double pipe heat exchanger using mechanical turbulators

    Science.gov (United States)

    Kamboj, Kushal; Singh, Gurjeet; Sharma, Rohit; Panchal, Dilbagh; Hira, Jaspreet

    2017-02-01

    The work presented here focuses on heat transfer augmentation by means of divergent-convergent spring turbulator (the enhancement device). Aim of the present work is to find such an optimum pitch at which the augmentation in heat transfer is maximum and the amount of power consumption is minimum, so that an economic design can be created with maximum thermal efficiency. So, the concept of pitch variation is introduced, which is defined as the horizontal distance between two consecutive turbulators. It describes that, the lesser is the pitch the more number of turbulators that can be inserted in inner pipe of double pipe heat exchanger, hence more will be the friction factor. This physics increases convective ability of the heat transfer process from the surface of inner pipe. There is a certain limit to which a pitch can be decreased, lesser the pitch the more the pressure drop and friction factor and hence the more will be the pumping power requirement to maintain a desired mass flow rate of hot water. Analysis of thermal factors such as Nusselts number, friction factor, with different pitches of divergent convergent spring turbulators of circular cross-section 15, 10, and 5 cm at Reynolds's number ranging between 9000 < Re < 40,000 is done graphically.

  8. Phenomenological and statistical analyses of turbulence in forced convection with temperature-dependent viscosity under non-Boussinesq condition.

    Science.gov (United States)

    Yahya, S M; Anwer, S F; Sanghi, S

    2013-10-01

    In this work, Thermal Large Eddy Simulation (TLES) is performed to study the behavior of weakly compressible Newtonian fluids with anisotropic temperature-dependent viscosity in forced convection turbulent flow. A systematic analysis of variable-viscosity effects, isolated from gravity, with relevance to industrial cooling/heating applications is being carried out. A LES of a planar channel flow with significant heat transfer at a low Mach number was performed to study effects of fluid property variation on the near-wall turbulence structure. In this flow configuration the top wall is maintained at a higher temperature (T hot ) than the bottom wall (T cold ). The temperature ratio (R θ = T hot /T cold ) is fixed at 1.01, 2 and 3 to study the effects of property variations at low Mach number. Results indicate that average and turbulent fields undergo significant changes. Compared with isothermal flow with constant viscosity, we observe that turbulence is enhanced in the cold side of the channel, characterized by locally lower viscosity whereas a decrease of turbulent kinetic energy is found at the hot wall. The turbulent structures near the cold wall are very short and densely populated vortices but near the hot wall there seems to be a long streaky structure or large elongated vortices. Spectral study reveals that turbulence is completely suppressed at the hot side of the channel at a large temperature ratio because no inertial zone is obtained (i.e. index of Kolmogorov scaling law is zero) from the spectra in these region.

  9. CFD Study of Deteriorated Turbulent Heat Transfer in Upward Flow

    Energy Technology Data Exchange (ETDEWEB)

    Nietiadi, Yohanes Setiawan; Lee, Jeong Ik [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Addad, Yacine [Khalifa University of Science and Technology and Research, Abu Dhabi (United Arab Emirates)

    2014-10-15

    DTHT regime can be induced by two effects: buoyancy and acceleration. Apart from these two deteriorating effects, another unique behavior of fluid in the DTHT regime is that the convective heat transfer rate will continue to deteriorate until it reaches certain point. The downstream of this point, is known as the recovery region, where the convective heat transfer rate returns back to the high values by recovering turbulence. We called this phenomena as re-turbulization.. The map of the DTHT regime can be seen from fig. 2, where the x-axis is the buoyancy parameter and y-axis is the acceleration parameter which is the agreed governing non-dimensional numbers among the researchers to illustrate the phenomena. The Buoyancy parameter is defind in Eq. (1) and the acceleration parameter is defined in Eq. (2), respectively. The threshold value for both effects to move from the forced turbulent heat transfer to the DTHT regime are found to be Bo* ≥ 2x10{sup -6}and Kv ≥ 2.5x10{sup -6} in the previous works. Bo{sup *}=Gr{sub q}/Re{sup 3}'.{sup 425} Pr{sup 0}'.{sup 8} (1). K{sub v}=4q{sup +}/Re (2). Many experiments and simulation have been done to investigate this phenomenon and the boundary of the regime. However, very limited number of experiment was conducted in the regime where buoyancy effect and acceleration effect are in the same order of magnitude and high enough to cause DTHT (mixed DTHT). Some important experimental researches that have been done in the gas DTHT regime is Lee et al. who investigated the heat transfer of gas flow in the range of buoyancy parameter from 3x10{sup -9} to 10{sup -5} and acceleration parameter span from 6x10{sup -8} to 5x10{sup -6} and presented the behavior of Nusselt number ratio from the experiment as fig. 3 and fig. 4. This paper will discuss a Computational Fluid Dynamics analysis on DTHT by assuming hypothetical boundary conditions especially on the mixed DTHT regime. It has been found that a gas cooled fast reactor

  10. A priori study of subgrid-scale features in turbulent Rayleigh-Bénard convection

    Science.gov (United States)

    Dabbagh, F.; Trias, F. X.; Gorobets, A.; Oliva, A.

    2017-10-01

    At the crossroad between flow topology analysis and turbulence modeling, a priori studies are a reliable tool to understand the underlying physics of the subgrid-scale (SGS) motions in turbulent flows. In this paper, properties of the SGS features in the framework of a large-eddy simulation are studied for a turbulent Rayleigh-Bénard convection (RBC). To do so, data from direct numerical simulation (DNS) of a turbulent air-filled RBC in a rectangular cavity of aspect ratio unity and π spanwise open-ended distance are used at two Rayleigh numbers R a ∈{1 08,1 010 } [Dabbagh et al., "On the evolution of flow topology in turbulent Rayleigh-Bénard convection," Phys. Fluids 28, 115105 (2016)]. First, DNS at Ra = 108 is used to assess the performance of eddy-viscosity models such as QR, Wall-Adapting Local Eddy-viscosity (WALE), and the recent S3PQR-models proposed by Trias et al. ["Building proper invariants for eddy-viscosity subgrid-scale models," Phys. Fluids 27, 065103 (2015)]. The outcomes imply that the eddy-viscosity modeling smoothes the coarse-grained viscous straining and retrieves fairly well the effect of the kinetic unfiltered scales in order to reproduce the coherent large scales. However, these models fail to approach the exact evolution of the SGS heat flux and are incapable to reproduce well the further dominant rotational enstrophy pertaining to the buoyant production. Afterwards, the key ingredients of eddy-viscosity, νt, and eddy-diffusivity, κt, are calculated a priori and revealed positive prevalent values to maintain a turbulent wind essentially driven by the mean buoyant force at the sidewalls. The topological analysis suggests that the effective turbulent diffusion paradigm and the hypothesis of a constant turbulent Prandtl number are only applicable in the large-scale strain-dominated areas in the bulk. It is shown that the bulk-dominated rotational structures of vortex-stretching (and its synchronous viscous dissipative structures) hold

  11. Numerical study of thermal performance of perforated circular pin fin heat sinks in forced convection

    Science.gov (United States)

    Wen, Mao-Yu; Yeh, Cheng-Hsiung

    2017-06-01

    This paper presents a numerical simulation of the heat transfer performance under forced convection for two different types of circular pin fin heat sinks with (Type A) and without (Type B) a hollow in the heated base. COMSOL Multiphysics, which is used for the thermal hydraulic analyses, has proven to be a powerful finite-element-based simulation tool for solving multiple physics-based systems of partial and ordinary differential equations. The standard κ - \\varepsilon two-equations turbulence model is employed to describe the turbulent structure and behavior. The numerical results are validated with the experimental results, and are shown to be in good agreement. The effects of the Reynolds number, height of the fin, finning factor and the perforated base plate on the heat-transfer coefficient are investigated and evaluated. The present study strongly recommends the use of a small hollow ( (Dh /Db ) heat sink.

  12. On the factors governing water vapor turbulence mixing in the convective boundary layer over land: Concept and data analysis technique using ground-based lidar measurements

    Energy Technology Data Exchange (ETDEWEB)

    Pal, Sandip, E-mail: sup252@PSU.EDU

    2016-06-01

    The convective boundary layer (CBL) turbulence is the key process for exchanging heat, momentum, moisture and trace gases between the earth's surface and the lower part of the troposphere. The turbulence parameterization of the CBL is a challenging but important component in numerical models. In particular, correct estimation of CBL turbulence features, parameterization, and the determination of the contribution of eddy diffusivity are important for simulating convection initiation, and the dispersion of health hazardous air pollutants and Greenhouse gases. In general, measurements of higher-order moments of water vapor mixing ratio (q) variability yield unique estimates of turbulence in the CBL. Using the high-resolution lidar-derived profiles of q variance, third-order moment, and skewness and analyzing concurrent profiles of vertical velocity, potential temperature, horizontal wind and time series of near-surface measurements of surface flux and meteorological parameters, a conceptual framework based on bottom up approach is proposed here for the first time for a robust characterization of the turbulent structure of CBL over land so that our understanding on the processes governing CBL q turbulence could be improved. Finally, principal component analyses will be applied on the lidar-derived long-term data sets of q turbulence statistics to identify the meteorological factors and the dominant physical mechanisms governing the CBL turbulence features. - Highlights: • Lidar based study for CBL turbulence features • Water vapor and aerosol turbulence profiles • Processes governing boundary layer turbulence profiles using lidars.

  13. Turbulent heat transport in two- and three-dimensional temperature fields

    Energy Technology Data Exchange (ETDEWEB)

    Samaraweera, Don Sarath Abesiri [Univ. of California, Berkeley, CA (United States)

    1978-03-01

    A fundamental numerical study of turbulent heat and mass transport processes in two- and three-dimensional convective flows is presented. The model of turbulence employed is the type referred to as a second-order closure. In this scheme transport equations for all nonzero components of the Reynolds stress tensor, for the isotropic dissipation rate of turbulent kinetic energy, for all nonzero scalar flux tensor components and for the mean square scalar fluctuations are solved by a finite difference method along with the mean momentum and mean enthalpy (or concentration) equations. The model used for the stresses was developed earlier. Parallel ideas were utilised in obtaining a model for turbulent heat and mass transfer processes. The study has focused especially on the problem of nonaxisymmetric convective heat and mass transport in pipes, which arises when the boundary conditions are not axisymmetric. The few available experimental data on such situations have indicated anisotropy in effective diffusivities. To expand the available data base an experiment was conducted to obtain heat transfer measurements in strong three-dimensional heating conditions. Numerical procedures especially suitable for incorporation of second-order turbulent closure models have been developed. The effect of circumferential conduction in the tube material, which is influential in the asymmetric heating data currently available, was accounted for directly by extending the finite difference calculations into the pipe wall. The principal goal of predicting three-dimensional scalar transfer has been achieved.

  14. Mantle Convection in a Microwave Oven: New Perspectives for the Internally Heated Convection

    Science.gov (United States)

    Limare, A.; Fourel, L.; Surducan, E.; Neamtu, C.; Surducan, V.; Vilella, K.; Farnetani, C. G.; Kaminski, E. C.; Jaupart, C. P.

    2015-12-01

    The thermal evolution of silicate planets is primarily controlled by the balance between internal heating - due to radioactive decay - and heat transport by mantle convection. In the Earth, the problem is particularly complex due to the heterogeneous distribution of heat sources in the mantle and the non-linear coupling between this distribution and convective mixing. To investigate the behaviour of such systems, we have developed a new technology based on microwave absorption to study internally-heated convection in the laboratory. This prototype offers the ability to reach the high Rayleigh-Roberts and Prandtl numbers that are relevant for planetary convection. Our experimental results obtained for a uniform distribution of heat sources were compared to numerical calculations reproducing exactly experimental conditions (3D Cartesian geometry and temperature-dependent physical properties), thereby providing the first cross validation of experimental and numerical studies of convection in internally-heated systems. We find that the thermal boundary layer thickness and interior temperature scale with RaH-1/4, where RaH is the Rayleigh-Roberts number, as theoretically predicted by scaling arguments on the dissipation of kinetic energy. Our microwave-based method offers new perspectives for the study of internally-heated convection in heterogeneous systems which have been out of experimental reach until now. We are able to selectively heat specific regions in the convecting layer, through the careful control of the absorption properties of different miscible fluids. This is analogous to convection in the presence of chemical reservoirs with different concentration of long-lived radioactive isotopes. We shall show results for two different cases: the stability of continental lithosphere over a convective fluid and the evolution of a hidden enriched reservoir in the lowermost mantle.

  15. Turbulent forced convection of nanofluids downstream an abrupt expansion

    Science.gov (United States)

    Kimouche, Abdelali; Mataoui, Amina

    2017-09-01

    Turbulent forced convection of Nanofluids through an axisymmetric abrupt expansion is investigated numerically in the present study. The governing equations are solved by ANYS 14.0 CFD code based on the finite volume method by implementing the thermo-physical properties of each nanofluid. All results are analyzed through the evolutions of skin friction coefficient and Nusselt number. For each nanofluid, the effect of both volume fraction and Reynolds number on this type of flow configuration, are examined. An increase on average Nusselt number with the volume fraction and Reynolds number, are highlighted and correlated. Two relationships are proposed. The first one, determines the average Nusselt number versus Reynolds number, volume fraction and the ratio of densities of the solid particles to that of the base fluid ( \\overline{Nu}=f(\\operatorname{Re},φ, ρ_s/ρ_f) ). The second one varies according Reynolds number, volume fraction and the conductivities ratio of solid particle to that of the base fluid ( \\overline{Nu}=f(\\operatorname{Re},φ, k_s/k_f) ).

  16. Temperature boundary layer profiles in turbulent Rayleigh-Benard convection

    Science.gov (United States)

    Ching, Emily S. C.; Emran, Mohammad S.; Horn, Susanne; Shishkina, Olga

    2017-11-01

    Classical boundary-layer theory for steady flows cannot adequately describe the boundary layer profiles in turbulent Rayleigh-Benard convection. We have developed a thermal boundary layer equation which takes into account fluctuations in terms of an eddy thermal diffusivity. Based on Prandtl's mixing length ideas, we relate the eddy thermal diffusivity to the stream function. With this proposed relation, we can solve the thermal boundary layer equation and obtain a closed-form expression for the dimensionless mean temperature profile in terms of two independent parameters: θ(ξ) =1/b∫0b ξ [ 1 +3a3/b3(η - arctan(η)) ] - c dη , where ξ is the similarity variable and the parameters a, b, and c are related by the condition θ(∞) = 1 . With a proper choice of the parameters, our predictions of the temperature profile are in excellent agreement with the results of our direct numerical simulations for a wide range of Prandtl numbers (Pr), from Pr=0.01 to Pr=2547.9. OS, ME and SH acknowledge the financial support by the Deutsche Forschungsgemeinschaft (DFG) under Grants Sh405/4-2 (Heisenberg fellowship), Sh405/3-2 and Ho 5890/1-1, respectively.

  17. Influence of the angle between the wind and the isothermal surfaces on the boundary layer structures in turbulent thermal convection.

    Science.gov (United States)

    Shishkina, Olga; Wagner, Sebastian; Horn, Susanne

    2014-03-01

    We derive the asymptotes for the ratio of the thermal to viscous boundary layer thicknesses for infinite and infinitesimal Prandtl numbers Pr as functions of the angle β between the large-scale circulation and an isothermal heated or cooled surface for the case of turbulent thermal convection with laminar-like boundary layers. For this purpose, we apply the Falkner-Skan ansatz, which is a generalization of the Prandtl-Blasius one to a nonhorizontal free-stream flow above the viscous boundary layer. Based on our direct numerical simulations (DNS) of turbulent Rayleigh-Bénard convection for Pr=0.1, 1, and 10 and moderate Rayleigh numbers up to 108 we evaluate the value of β that is found to be around 0.7π for all investigated cases. Our theoretical predictions for the boundary layer thicknesses for this β and the considered Pr are in good agreement with the DNS results.

  18. Neutron Scattering Study of Transitions to Convection and Turbulence in Nematic Para-Azoxyanisole

    DEFF Research Database (Denmark)

    Bjerrum Møller, Hans; Riste, T.

    1975-01-01

    The critical temperature gradients for the onset of convection and turbulence were measured in nematic para-azoxyanisole. The transition to turbulence was found to occur through two successive instabilities. The first of these clearly signals the entrance to a periodic-motion regime, and the second...

  19. A numerical study of momentum and forced convection heat transfer ...

    African Journals Online (AJOL)

    A numerical study has been carried out to examine the momentum and turbulent forced-convection characteristics for airflow through a constant temperature- surfaced rectangular duct with top and lower wallmounted waved baffles.Air is the working fluid with the flow rate in terms of Reynolds numbers ranging from 5,000 to ...

  20. Penetrative internally heated convection in two and three dimensions

    NARCIS (Netherlands)

    Goluskin, D.; van der Poel, Erwin

    2016-01-01

    Convection of an internally heated fluid, confined between top and bottom plates of equal temperature, is studied by direct numerical simulation in two and three dimensions. The unstably stratified upper region drives convection that penetrates into the stably stratified lower region. The fraction

  1. Measurements of convective and radiative heating in wildland fires

    Science.gov (United States)

    David Frankman; Brent W. Webb; Bret W. Butler; Daniel Jimenez; Jason M. Forthofer; Paul Sopko; Kyle S. Shannon; J. Kevin Hiers; Roger D. Ottmar

    2012-01-01

    Time-resolved irradiance and convective heating and cooling of fast-response thermopile sensors were measured in 13 natural and prescribed wildland fires under a variety of fuel and ambient conditions. It was shown that a sensor exposed to the fire environment was subject to rapid fluctuations of convective transfer whereas irradiance measured by a windowed sensor was...

  2. Bursting and large-scale intermittency in turbulent convection with differential rotation

    DEFF Research Database (Denmark)

    Garcia, O.E.; Bian, N.H.

    2003-01-01

    The tilting mechanism, which generates differential rotation in two-dimensional turbulent convection, is shown to produce relaxation oscillations in the mean flow energy integral and bursts in the global fluctuation level, akin to Lotka-Volterra oscillations. The basic reason for such behavior...... of convective turbulence, as manifested by exponential tails in single-point probability distribution functions. Moreover, the spatio-temporal evolution of convective structures illustrates the mechanism triggering avalanche events in the transport process. The latter involves the overlap of delocalized mixing...

  3. Extreme-value statistics from Lagrangian convex hull analysis I. Validation for homogeneous turbulent Boussinesq convection and MHD convection

    CERN Document Server

    Pratt, J; Müller, W -C; Chapman, S C; Watkins, N W

    2016-01-01

    We investigate the utility of the convex hull to analyze physical questions related to the dispersion of a group of much more than four Lagrangian tracer particles in a turbulent flow. Validation of standard dispersion behaviors is a necessary preliminary step for use of the convex hull to describe turbulent flows. In simulations of statistically homogeneous and stationary Navier-Stokes turbulence, neutral fluid Boussinesq convection, and MHD Boussinesq convection we show that the convex hull can be used to reasonably capture the dispersive behavior of a large group of tracer particles. We validate dispersion results produced with convex hull analysis against scalings for Lagrangian particle pair dispersion. In addition to this basic validation study, we show that convex hull analysis provides information that particle pair dispersion does not, in the form of a extreme value statistics, surface area, and volume for a cluster of particles. We use the convex hull surface area and volume to examine the degree of...

  4. Shear heating in creeping faults changes the onset of convection

    Science.gov (United States)

    Tung, R.; Poulet, T.; Alevizos, S.; Veveakis, E.; Regenauer-Lieb, K.

    2017-10-01

    The interaction between mechanical deformation of creeping faults and fluid flow in porous media has an important influence on the heat and mass transfer processes in Earth sciences. Creeping faults can act as heat sources due to the effect of shear heating and as such could be expected to alter the conditions for hydrothermal convection. In this work, we provide a finite element-based numerical framework developed to resolve the problem of heat and mass transfer in the presence of creeping faults. This framework extends the analytical approach of the linear stability analysis (LSA) frequently used to determine the bifurcation criterion for onset of convection, allowing us to study compressible cases with the option of complex geometry and/or material inhomogeneities. We demonstrate the impact of creeping faults on the onset of convection and show that shear heating—expressed through its dimensionless group the Gruntfest number Gr—has exponential influence on the critical value of the Lewis number Le (inversely proportional to the Rayleigh number Ra) required for convection: Lec ˜ Lec0 eGr. In this expression, Lec0 is the critical value of Le in the absence of shear heating. This exponential scaling shows that shear heating increases the critical Lewis number and triggers hydrothermal convection at lower permeability than in situations without it. We also show that the effect of shear heating in a fault significantly alters the pattern of convection in and around the fault zone.

  5. Large–eddy simulations of wall heat transfer and coherent structures in mixed convection over a wavy wall

    NARCIS (Netherlands)

    Kuhn, S.; Kenjeres, S.; Von Rohr, P.R.

    2009-01-01

    In this numerical study the mixed convective flow of water over a heated wavy surface over a range of Reynolds and Richardson numbers, including transitional and turbulent flow regimes (20 ? Re ? 2000 and 0.5 ? Ri ? 5000) is investigated. A dynamic Large Eddy Simulation (LES) approach is applied

  6. Control of wave-driven turbulence and surface heating on the mixing of microplastic marine debris

    Science.gov (United States)

    Kukulka, T.; Lavender Law, K. L.; Proskurowski, G. K.

    2016-02-01

    Buoyant microplastic marine debris (MPMD) is a pollutant in the ocean surface boundary layer (OSBL) that is submerged by turbulent transport processes. Langmuir circulation (LC) is a turbulent process driven by wind and surface waves that enhances mixing in the OSBL. Sea surface cooling also contributes to OSBL turbulence by driving convection. On the other hand, sea surface heating stratifies and stabilizes the water column to reduce turbulent motion. We analyze observed MPMD surface concentrations in the Atlantic and Pacific Oceans to reveal a significant increase in MPMD concentrations during surface heating and a decrease during surface cooling. Turbulence resolving large eddy simulations of the OSBL for an idealized diurnal heating cycle suggest that turbulent downward fluxes of buoyant tracers are enhanced at night, facilitating deep submergence of plastics, and suppressed in heating conditions, resulting in surface trapped MPMD. Simulations agree with observations if enhanced mixing due to LC is included. Our results demonstrate the controlling influence of surface heat fluxes and LC on turbulent transport in the OSBL and on vertical distributions of buoyant marine particles.

  7. On sound generation by turbulent convection: A new look at old results

    Science.gov (United States)

    Musielak, Z. E.; Rosner, R.; Stein, R. F.; Ulmschneider, P.

    1994-01-01

    We have revisited the problem of acoustic wave generation by turbulent convection in stellar atmospheres. The theory of aerodynamically generated sound, originally developed by Lighthill and later modified by Stein to include the effects of stratification, has been used to estimate the acoustic wave energy flux generated in solar and stellar convection zones. We correct the earlier computations by incorporating an improved description of the spatial and temporal spectrum of the turbulent convection. We show the dependence of the resulting wave fluxes on the nature of the turbulence, and compute the wave energy spectra and wave energy fluxes generated in the Sun on the basis of a mixing-length model of the solar convection zone. In contrast to the previous results, we show that the acoustic energy generation does not depend very sensitively on the turbulent energy spectrum. However, typical total acoustic fluxes of order F(sub A) = 5 x 10(exp 7) ergs/sq cm/s with a peak of the acoustic frequency spectrum near omega = 100 mHz are found to be comparable to those previously calculated. The acoustic flux turns out to be strongly dependent on the solar model, scaling with the mixing-length parameter alpha as alpha(exp 3.8). The computed fluxes most likely constitute a lower limit on the acoustic energy produced in the solar convection zone if recent convection simulations suggesting the presence of shocks near the upper layers of the convection zone apply to the Sun.

  8. Natural convective heat transfer from short inclined cylinders

    CERN Document Server

    Oosthuizen, Patrick H

    2014-01-01

    Natural Convective Heat Transfer from Short Inclined Cylinders  examines a heat transfer situation of significant, practical importance not adequately dealt with in existing textbooks or in any widely available review papers. Specifically, the book introduces the reader to recent studies of natural convection from short cylinders mounted on a flat insulated base where there is an “exposed” upper surface. The authors considers the effects of the cylinder cross-sectional shape, the cylinder inclination angle, and the length-to-cross sectional size of the cylinder. Both numerical and experimental studies are discussed and correlation equations based on the results of these studies are reviewed. This book is ideal for professionals involved with thermal management and related systems, researchers, and graduate students in the field of natural convective heat transfer, instructors in graduate level courses in convective heat transfer.

  9. Convective heat and mass transfer in rotating disk systems

    CERN Document Server

    Shevchuk, Igor V

    2009-01-01

    The book describes results of investigations of a series of convective heat and mass transfer problems in rotating-disk systems. Methodology used included integral methods, self-similar and approximate analytical solutions, as well as CFD.

  10. Free convection effects and radiative heat transfer in MHD Stokes ...

    Indian Academy of Sciences (India)

    which controls the gasification rate of the energetic material for estimating heat transfer. Radiation effect on flow and heat transfer is important in the context of space technology and processes involving high temperature. In recent years, the problems of free convective and heat transfer flows through a porous medium under ...

  11. Heat transfer of laminar mixed convection of liquid

    CERN Document Server

    Shang, De-Yi

    2016-01-01

    This book presents a new algorithm to calculate fluid flow and heat transfer of laminar mixed convection. It provides step-by-step tutorial help to learn quickly how to set up the theoretical and numerical models of laminar mixed convection, to consider the variable physical properties of fluids, to obtain the system of numerical solutions, to create a series of formalization equations for the convection heat transfer by using a curve-fitting approach combined with theoretical analysis and derivation. It presents the governing ordinary differential equations of laminar mixed convection, equivalently transformed by an innovative similarity transformation with the description of the related transformation process. A system of numerical calculations of the governing ordinary differential equations is presented for the water laminar mixed convection. A polynomial model is induced for convenient and reliable treatment of variable physical properties of liquids. The developed formalization equations of mixed convec...

  12. Study on the natural convection heat transfer characteristics in the air duct

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Y. K.; Lee, Y. B.; Choi, S. K.; Hwang, J. S.; Nam, H. Y. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1997-12-31

    Temperature distribution measurements in the mockup apparatus of reactor vessel were performed to determine the effective thermal conductivity of porous media with different geometry and to obtain the experimental data for the heat transfer processes by natural convection occurring in the air duct. The temperature distributions at four separated sections with different arrangements of porous media have different slopes according to the geometrical configuration. From the measured temperature distribution, effective thermal conductivity have been derived using the least square fitting method. The test at air duct was performed to the high heat removal at 3.4kW/m{sup 2} by the natural convection from the outer wall to the air. And also the temperature distributions in the sir duct agree well with the 1/7th power-law turbulent temperature distribution. The obtained heat transfer data have been compared with the Shin`s and Sieger`s correlations. 10 refs., 6 figs. (Author)

  13. Penetrative convective flows induced by internal heating and mantle compressibility

    Science.gov (United States)

    Machetel, Philippe; Yuen, David A.

    1989-01-01

    Penetrative convective flows induced in a spherical shell by combined effects of internal heating and mantle compressibility are investigated using mathematical and numerical formulations for compressible spherical shell convection. Isothermal stress-free boundary conditions applied at the top and the bottom of the shell are solved using a time-dependent finite difference code in a temperature, vorticity, stream function formulation for Rayleigh numbers ranging from the critical Rc up to 2000 Rc. Results indicate that compressibility, together with internal heating, could be a mechanism capable of generating spontaneously layered convection and local melting in the mantle and that non-Boussinesq effects must be considered in interpretations of geophysical phenomena.

  14. Theory of heat transfer with forced convection film flows

    CERN Document Server

    Shang, Deyi

    2010-01-01

    Developing a new treatment of ""Free Convection Film Flows and Heat Transfer"" began in Shang's first monograph and is continued in this monograph. The current book displays the recent developments of laminar forced convection and forced film condensation. It is aimed at revealing the true features of heat and mass transfer with forced convection film flows to model the deposition of thin layers. The novel mathematical similarity theory model is developed to simulate temperature - and concentration - dependent physical processes. The following topics are covered in this book: Mathematical meth

  15. Forced convection heat transfer in integrated microchannel heat sinks

    Science.gov (United States)

    Lee, Man

    A microchannel heat sink, integrated with pressure and temperature microsensors, was fabricated to study convective boiling under uniform heat flux boundary condition. Utilizing a wafer bond and etch back technology, the heat source, temperature and pressure sensors were separated from the fluid flow by a membrane only 1.5mum in thickness; thus allowing good control of the thermal boundary conditions. Temperature and pressure distributions for various power levels and flow rates were measured. Single-phase liquid flow results, compared with numerical simulations, confirm that the heat flux boundary condition is indeed nearly uniform. The sensor arrays, particularly for two-phase flow, provide the spatial and temporal dependence of both the temperature and pressures fields. During two-phase flow, a pressure peak appears at the location of the liquid-vapor interface region. Simultaneously, qualitative visualizations of the evolving flow patterns have been correlated with quantitative temperature and pressure measurements. Based on the temperature and pressure measurements inside the microchannels, the empirical correlations of local pressure fluctuation frequency and pressure fluctuation amplitude are found to increase with increasing input power and Suratman number, but with decreasing Reynolds number. A flow regime map is plotted to distinguish the different kinds of flow pattern in microchannels. Moreover, the activity of nucleation sites as well as the ensuing bubble dynamics, from incipience to departure, was found to depend on the channel height. The critical size for active nucleation site increases with increasing microchannel height. Furthermore, size and shape effects on two-phase flow patterns in forced convection boiling were investigated in near rectangular microchannels with silicon substrate. Although detected, in contrast with triangular microchannels, annular flow was observed to be unstable. Instead, the dominant flow pattern was an unsteady

  16. Solution of heat removal from nuclear reactors by natural convection

    Directory of Open Access Journals (Sweden)

    Zitek Pavel

    2014-03-01

    Full Text Available This paper summarizes the basis for the solution of heat removal by natural convection from both conventional nuclear reactors and reactors with fuel flowing coolant (such as reactors with molten fluoride salts MSR.The possibility of intensification of heat removal through gas lift is focused on. It might be used in an MSR (Molten Salt Reactor for cleaning the salt mixture of degassed fission products and therefore eliminating problems with iodine pitting. Heat removal by natural convection and its intensification increases significantly the safety of nuclear reactors. Simultaneously the heat removal also solves problems with lifetime of pumps in the primary circuit of high-temperature reactors.

  17. A DIMENSIONLESS SOLUTION TO RADIATION AND TURBULENT NATURAL CONVECTION IN SQUARE AND RECTANGULAR ENCLOSURES

    Directory of Open Access Journals (Sweden)

    A. K. A. SHATI

    2012-04-01

    Full Text Available The effects of natural convection with and without the interaction of surface radiation in square and rectangular enclosures have been studied, numerically and theoretically. The analyses were carried out over a wide range of enclosure aspect ratios ranging from 0.0625 to 16, including square enclosures in sizes from 40cm to 240cm, with cold wall temperatures ranging from 283 to 373 K, and hot to cold temperature ratios ranging from 1.02 to 2.61. The work was carried out using four different fluids whose properties are varying with temperature. FLUENT software was used to carry out the numerical study. Turbulence was modelled using the RNG k-ε model with a non-uniform grid. The Discrete Transfer Radiation Model (DTRM was used for radiation simulation. A correlation equation for the new dimensionless group represented by the ratio of natural convection to radiation, as a function of Nusselt, Grashof, Prandtl numbers and temperature ratio also, the average Nusselt number without radiation as a function of Grashof and Prandtl numbers have been provided along with the constants needed to use them as a function of temperature ratio. This provides a generalised equation for heat transfer in square and rectangular enclosures both with and without radiation.

  18. Aspects of forced convective heat transfer in geothermal systems

    Energy Technology Data Exchange (ETDEWEB)

    Kilty, K.; Chapman, D.S.; Mase, C.

    1978-07-01

    A knowledge of convective heat transfer is essential to understanding geothermal systems and other systems of moving groundwater. A simple, kinematic approach toward convective heat transfer is taken here. Concern is not with the cause of the groundwater motion but only with the fact that the water is moving and transferring heat. The mathematical basis of convective heat transfer is the energy equation which is a statement of the first law of thermodynamics. The general solution of this equation for a specific model of groundwater flow has to be done numerically. The numerical algorithm used here employs a finite difference approximation to the energy equation that uses central differences for the heat conduction terms and one-sided differences for the heat convection terms. Gauss--Seidel iteration is then used to solve the finite difference equation at each node of a non-uniform mesh. The Monroe and Red Hill hot springs, a small hydrothermal system in central Utah, provide an example to illustrate the application of convective heat transfer theory to a geophysical problem. Two important conclusions regarding small geothermal systems follow immediately from the results of this application. First, the most rapid temperature rise in the convecting part of a geothermal system is near the surface. Below this initially rapid temperature increase the temperature increases very slowly, and thus temperatures extrapolated from shallow boreholes can be seriously in error. Second, the temperatures and heat flows observed at Monroe and Red Hill, and probably at many other small geothermal areas, can easily result from moderate vertical groundwater velocities in faults and fracture zones in an area of normal heat flow.

  19. Natural convection of nanofluids over a convectively heated vertical plate embedded in a porous medium

    Energy Technology Data Exchange (ETDEWEB)

    Ghalambaz, M.; Noghrehabadi, A.; Ghanbarzadeh, A., E-mail: m.ghalambaz@gmail.com, E-mail: ghanbarzadeh.a@scu.ac.ir [Department of Mechanical Engineering, Shahid Chamran University of Ahvaz, Ahvaz (Iran, Islamic Republic of)

    2014-04-15

    In this paper, the natural convective flow of nanofluids over a convectively heated vertical plate in a saturated Darcy porous medium is studied numerically. The governing equations are transformed into a set of ordinary differential equations by using appropriate similarity variables, and they are numerically solved using the fourth-order Runge-Kutta method associated with the Gauss-Newton method. The effects of parametric variation of the Brownian motion parameter (Nb), thermophoresis parameter (Nt) and the convective heating parameter (Nc) on the boundary layer profiles are investigated. Furthermore, the variation of the reduced Nusselt number and reduced Sherwood number, as important parameters of heat and mass transfer, as a function of the Brownian motion, thermophoresis and convective heating parameters is discussed in detail. The results show that the thickness of the concentration profiles is much lower than the temperature and velocity profiles. For low values of the convective heating parameter (Nc), as the Brownian motion parameter increases, the non-dimensional wall temperature increases. However, for high values of Nc, the effect of the Brownian motion parameter on the non-dimensional wall temperature is not significant. As the Brownian motion parameter increases, the reduced Sherwood number increases and the reduced Nusselt number decreases. (author)

  20. NANOFLUID PROPERTIES FOR FORCED CONVECTION HEAT TRANSFER: AN OVERVIEW

    Directory of Open Access Journals (Sweden)

    W.H.Azmi

    2013-06-01

    Full Text Available Nanofluids offer a significant advantage over conventional heat transfer fluids and consequently, they have attracted much attention in recent years. The engineered suspension of nano-sized particles in a base liquid alters the properties of these nanofluids. Many researchers have measured and modeled the thermal conductivity and viscosity of nanofluids. The estimation of forced convective heat transfer coefficients is done through experiments with either metal or nonmetal solid particles dispersed in water. Regression equations are developed for the determination of the thermal conductivity and viscosity of nanofluids. The parameters influencing the decrease in convection heat transfer, observed by certain investigators, is explained.

  1. Free convection effects and radiative heat transfer in MHD Stokes ...

    Indian Academy of Sciences (India)

    The present note deals with the effects of radiative heat transfer and free convection in MHD for a flow of an electrically conducting, incompressible, dusty viscous fluid past an impulsively started vertical non-conducting plate, under the influence of transversely applied magnetic field. The heat due to viscous dissipation and ...

  2. Heat Transfer Correlations for Free Convection from Suspended Microheaters

    Directory of Open Access Journals (Sweden)

    David GOSSELIN

    2016-08-01

    Full Text Available Portability and autonomy for biomedical diagnostic devices are two rising requirements. It is recognized that low-energy heating of such portable devices is of utmost importance for molecular recognition. This work focuses on screen-printed microheaters based on on Joule effect, which constitute an interesting solution for low-energy heating. An experimental study of the natural convection phenomena occurring with such microheaters is conducted. When they are suspended in the air, and because of the thinness of the supporting film, it is shown that the contributions of both the upward and downward faces have to be taken into account. A total Nusselt number and a total convective heat transfer coefficient have been used to describe the natural convection around these microheaters. In addition a relation between the Nusselt number and the Rayleigh number is derived, leading to an accurate prediction of the heating temperature (MRE< 2 %.

  3. Simulation of Turbulent Natural Convection in a Local Zone of Largescale Area Under Conditions of the Radiant Energy Supply

    Directory of Open Access Journals (Sweden)

    Nee Alexander

    2016-01-01

    Full Text Available This paper presents the results of mathematical modelling of turbulent natural convection under conditions of the conjugate heat transfer in an open cavity heated by infrared emitter. Two-dimensional problem of heat transfer was formulated in the vorticity - stream function - temperature dimensionless variables and solved by means of the finite difference method on a uniform grid. According to the results of numerical analysis, the fields of differential and integral heat transfer characteristics, illustrating the unsteady nature of the thermophysical process under study, were obtained. The nonlinear dependence of the average Nusselt number versus dimensionless time (τ was established. It was shown that the average Nusselt number monotonically increased in a range of 800<τ<2000

  4. Convection patterns in end-heated inclined enclosures.

    Science.gov (United States)

    Delgado-Buscalioni, R

    2001-07-01

    The natural convection in inclined side-heated rectangular boxes with adiabatic walls is theoretically and numerically investigated. The study is focused on the characterization of the convection patterns arising at the core of the basic steady unicellular flow and covers the whole range of Prandtl numbers (0enclosures illustrate each type of multicellular flow and examples of instability interactions near the codimension-2 lines predicted by the theory.

  5. Investigation of Transient, Turbulent Natural Convection in Vertical Tubes for Thermal Energy Storage in Supercritical CO2

    Science.gov (United States)

    Baghaei Lakeh, Reza; Lavine, Adrienne S.; Kavehpour, H. Pirouz; Wirz, Richard E.

    2013-11-01

    Heat transfer can be a limiting factor in the operation of thermal energy storage, including sensible heat and latent heat storage systems. Poor heat transfer between the energy storage medium and the container walls impairs the functionality of the thermal storage unit by requiring excessively long times to charge or discharge the system. In this study, the effect of turbulent, unsteady buoyancy-driven flow on heat transfer in vertical storage tubes containing supercritical CO2 as the storage medium is investigated computationally. The heat transfer from a constant-temperature wall to the storage fluid is studied during the charge cycle. The results of this study show that turbulent natural convection dominates the heat transfer mechanism and significantly reduces the required time for charging compared to pure conduction. Changing the L/D ratio of the storage tube has a major impact on the charge time. The charge time shows a decreasing trend with RaL. The non-dimensional model of the problem shows that Nusselt number and non-dimensional mean temperature of the storage fluid in different configurations of the tube is a function Buoyancy-Fourier number defined as of FoL * RaLm* L/D. This study was supported by award No. DE-AR0000140 granted by U.S. Department of Energy under Advanced Research Projects Agency - Energy (ARPA-E) and by award No. 5660021607 granted by Southern California Gas Company.

  6. Convective Heat Transfer Coefficients of the Human Body under Forced Convection from Ceiling

    DEFF Research Database (Denmark)

    Kurazumi, Yoshihito; Rezgals, Lauris; Melikov, Arsen Krikor

    2014-01-01

    The average convective heat transfer coefficient for a seated human body exposed to downward flow from above was determined. Thermal manikin with complex body shape and size of an average Scandinavian female was used. The surface temperature distribution of the manikin’s body was as the skin...... of the convective heat transfer coefficient of the whole body (hc [W/(m2•K)]) was proposed: hc=4.088+6.592V1.715 for a seated naked body at 20ºC and hc=2.874+7.427V1.345 for a seated naked body at 26ºC. Differences in the convective heat transfer coefficient of the whole body in low air velocity range, V

  7. Numerical simulations of soft and hard turbulence - Preliminary results for two-dimensional convection

    Science.gov (United States)

    Deluca, E. E.; Werne, J.; Rosner, R.; Cattaneo, F.

    1990-01-01

    Results on the transition from soft to hard turbulence in simulations of two-dimensional Boussinesq convection are reported. The computed probability densities for temperature fluctuations are exponential in form in both soft and hard turbulence, unlike what is observed in experiments. In contrast, a change is obtained in the Nusselt number scaling on Rayleigh number in good agreement with the three-dimensional experiments.

  8. CONVECTIVE HEAT EXCHANGE ON THE LATERAL SURFACE OF A RELATIVELY LONG CYCLONE CHAMBER

    Directory of Open Access Journals (Sweden)

    E. N. Saburov

    2016-01-01

    Full Text Available The high-turbulent swirling flows of heat carrier that are created by a cyclone chamber are used in industry. They make it possible to intensify processes of heat and mass exchange. The results of an experimental study of convective heat transfer on the lateral surface of the active volume of a relatively long cyclone chamber considerably exceeding the length of the chambers that were used in previously performed studies are presented and analyzed in the article. Air supply in the swirler of the chamber was performed tangentially from diametrically opposite sides of the two input channels. The gas outlet was implemented from the opposite end. The heat transfer by convection to the swirling air flow was studied by the method of changing the state of aggregation of a heating agent – condensation of slightly superheated steam. Collecting condensate from the working section was made through a water seal for maintaining a constant pressure calorimeter. The amount of heat transferred during experiment was determined by weight of the collected condensate. The specific features of influence of geometrical characteristics of cyclone chamber on intensity of heat exchange are considered. In the experiments we varied the relative diameter of the outlet port of the chamber dвых and the relative area of the input channels fвх. Segmental construction of the chamber made it possible to move a calorimeter on its length. The local heat transfer coefficient was determined for various values of the dimensionless longitudinal coordinate z coinciding with the axis of the chamber, and counted from the back end of the swirler. The estimated equations of heat transfer obtained during the research are presented and recommended for use in practice of engineering. The considered problem is of an interest from the point of view of further research of aerodynamics and of convective heat transfer in a highly swirling flow cyclone devices, in order to improve the

  9. Numerical investigations on the turbulent forced convection of nanofluids flow in a triangular-corrugated channel

    Directory of Open Access Journals (Sweden)

    M.A. Ahmed

    2015-09-01

    Full Text Available In this paper, turbulent forced convection of nanofluids flow in triangular-corrugated channels is numerically investigated over Reynolds number ranges of 1000–5000. Four different types of nanofluids which are Al2O3, CuO, SiO2 and ZnO–water with nanoparticles diameters in the range of 30–70 nm and the range of nanoparticles volume fraction from 0% to 4% have been considered. The governing equations of mass, momentum and energy are solved using finite volume method (FVM. The low Reynolds number k–ε model of Launder and Sharma is adopted as well. It is found that the average Nusselt number, pressure drop, heat transfer enhancement, thermal–hydraulic performance increase with increasing in the volume fraction of nanoparticles and with decreasing in the diameter of nanoparticles. Furthermore, the SiO2–water nanofluid provides the highest thermal–hydraulic performance among other types of nanofluids followed by Al2O3, ZnO and CuO–water nanofluids. Moreover, the pure water has the lowest heat transfer enhancement as well as thermal–hydraulic performance.

  10. Turbulent convection experiment at high Rayleigh number to support CAP1400 IVR strategy

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Li, E-mail: mali@snptrd.com [State Nuclear Hua Qing(Beijing) Nuclear Power Technology R& D Centre Co., Ltd, Building A, State Nuclear Power Research Institute, Future Science & Technology Park, Changping Dist., Beijing 102209 (China); Li, Jing, E-mail: lijing@snptrd.com [State Nuclear Hua Qing(Beijing) Nuclear Power Technology R& D Centre Co., Ltd, Building A, State Nuclear Power Research Institute, Future Science & Technology Park, Changping Dist., Beijing 102209 (China); Ji, Shui, E-mail: jishui@snptrd.com [State Nuclear Hua Qing(Beijing) Nuclear Power Technology R& D Centre Co., Ltd, Building A, State Nuclear Power Research Institute, Future Science & Technology Park, Changping Dist., Beijing 102209 (China); Chang, Huajian, E-mail: changhuajian@snptrd.com [State Nuclear Hua Qing(Beijing) Nuclear Power Technology R& D Centre Co., Ltd, Building A, State Nuclear Power Research Institute, Future Science & Technology Park, Changping Dist., Beijing 102209 (China); Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China)

    2015-10-15

    Highlights: • The facility reached high Ra number at 10{sup 12} of CAP1400 working condition. • The fitting formula Nu = 0.085 × Ra{sup 0.315} was established to calculate the heat flux in the metal layer at high Ra for the CAP1400. • The coupling method can accurately and safely predict the heat flow distribution of metal layer in high Ra number conditions. • The experiment results will predict the relationship between axial and radial heat transfer well. - Abstract: The characteristics of the heat transfer and the calculation of heat flux in metal layer are both the critical problems for in-vessel retention (IVR) strategy. Turbulent convection occurs in the metal layer when the Rayleigh number (Ra) becomes sufficient high. The Globe–Dropkin (G–D) correlation (Globe and Dropkin, 1959) and Chu–Churchill (C–C) correlation (Churchill and Chu, 1975) have been widely used to calculate the heat flux in the metal layer, where the valid range of the Ra is from 1.5 × 10{sup 5} to 6.8 × 10{sup 8} in G–D correlation and less than 10{sup 12} in C–C correlation. However, with the increase of reactor power, both the Rayleigh number and the rate of heat transfer below the bottom of metal layer of the molten pool will increase, and in this case the Rayleigh number even can reach 10{sup 11} for the China Advanced Passive Plant CAP1400. Accordingly, the G–D correlation is not suitable for the CAP1400. Therefore, our experiment purposes are to establish the appropriate correlation at high Ra for the CAP1400 and predict the axial and radial distribution of the heat transfer in the metal layer with the heat transfer behavior of metal layer experiment (HELM) facility. The experiments are divided into two parts. Each part concerns 39 runs and 47 experimental conditions. Its corresponding results are obtained at middle Prandtl number (Pr = 7 for water) and the Nusselt number is found to be proportional to Ra{sup 0.315} in the range 3.93 × 10{sup 8} < Ra < 3.57

  11. A numerical exercise for turbulent natural convection and pollutant diffusion in a two-dimensional partially partitioned cavity

    Energy Technology Data Exchange (ETDEWEB)

    Jobert, Patrice; Beghein, Claudine; Sergent, Anne [LEPTAB, Universite de La Rochelle (France); Le Quere, Patrick [LIMSI, CNRS, Orsay (France); Collignan, Bernard; Couturier, Stephane [CSTB, Marne La Vallee (France); Glockner, Stephane; Vincent, Stephane [MASTER, ENSCPB, Pessac (France); Groleau, Dominique; Lubin, Pierre [CERMA, CNRS, Nantes (France)

    2005-04-01

    We present the results of a numerical exercise aimed at comparing the predictions of different conventional turbulent modelling approaches for natural convection at Rayleigh numbers characteristic of applications such as energy savings, fire safety or thermal comfort. A two-dimensional configuration was considered that consists of two adjacent rooms separated by a lintel in which natural convection is induced through heating on their opposite sides and subjected to diffusion of a pollutant from one room to the other. Seven contributions are available. The comparison is carried out, in terms of local or global quantities, for the mean thermal and dynamic fields and for the unsteady diffusion of the pollutant from one room to the other. Characteristic differences between steady RANS and unsteady two-dimensional DNS and LES approaches are observed and discussed. (authors)

  12. Thermo capillary and buoyancy convection in a fluid locally heated on its free surface; Convection thermocapillaire et thermogravitaire dans un fluide chauffe localement sur sa surface libre

    Energy Technology Data Exchange (ETDEWEB)

    Favre, E.

    1997-09-26

    coupled buoyancy and thermo-capillary convection lead to a convective motion of the interface liquid/gas which drastically changes the heat and mass transfer across the liquid layer. Two experiments were considered, depending on the fluid: oil or mercury. The liquid is set in a cooled cylindrical vessel, and heated by a heat flux across the center of the free surface. The basic flow, in the case of oil, is a torus. When the heat parameter increases, a stationary flow appears as petals or rays when the aspect ratio. The lateral confinement selects the azimuthal wavelength. In the case of petals-like flow, a sub-critical Hopf bifurcation is underlined. The turbulence is found to be `weak`, even for the largest values of the Marangoni number (Ma = 1.3 10{sup 5}). In the case of mercury, the thermo-capillary effect is reduced to zero to impurities at the surface which have special trajectories we describe and compare to a simpler experiment. Only the buoyancy forces induce a unstationary, weakly turbulent flow as soon as the heating power exceeds 4W (Ra = 4.5 10{sup 3}, calculated with h = 1 mm). The past part concerns the analysis of the effect on the flow of the boundary conditions, the geometry, the Prandtl number and the buoyancy force with the help of the literature. Results concerning heat transfer, in particular the exponent of the law Nusselt number vs. heating power, were compared with available data. (author) 115 refs.

  13. Heating of matter by microwaves without convection

    OpenAIRE

    Drašković, Draško

    2012-01-01

    This thesis considers heating of matter by means of microwaves. The most common device that uses micro waves for the heating of matter is the microwave oven. Because of the microwave ovens ubiquity and accessibility there are many articles that address the way it works and in how it heats matter. However, it appears that articles contradict each other in their claims that the heating of the matter is either from the inside or from the outside. What actually means »heating the material in the...

  14. CFD-simulations of turbulent convective flows at supercritical pressure; CFD-Simulationen turbulenter konvektiver Stroemungen bei ueberkritischen Druecken

    Energy Technology Data Exchange (ETDEWEB)

    Kunik, Claus

    2012-07-10

    In the year 2000, six innovative reactor concepts have been proposed by the Generation IV International Forum (GIF) for a detailed investigation. One of those concepts is the so-called Supercritical Water Reactor (SCWR), which uses water at supercritical pressure conditions as coolant. Accordingly, there is a significant improvement of heat transfer at standard operation conditions. Fluids at pressure conditions around the thermodynamic critical point exhibit strong variations of fluid properties, which occur suddenly in a narrow temperature range. Those changes interact with the production of turbulence in the near wall area and can cause an deterioration of heat transfer. Consequently, this can lead to overheating of components and material problems. To analyse this safety-related phenomena, several experiments are performed in the past, which usually are very expensive and restricted with respect to turbulence data. Therefore, fundamental numerical investigations on fluid flow and heat transfer at supercritical pressure are required. In the first step, a numerical method, which is adapted on supercritical pressure conditions, is developed. This method bases on the so-called low Mach-number approximation and on a system of equations, which is coupled by the temperature dependent thermophysical properties. Because of lower computational costs, this approach will be applied on the Reynolds Averaged Navier-Stokes (RANS) method at first. After the verification with help of a strongly heated air flow, the approach will be applied on forced and mixed convection conditions at supercritical pressure. The results are compared with direct numerical simulation (DNS) data from the literature. Based on this analysis, an adapted turbulence model, is developed. In the second step of this work, the approach will be applied on the Large Eddy Simulation (LES) method, which allows the resolution of turbulent structures. After verification with help of an externally heated channel

  15. Natural convection heat transfer within horizontal spent nuclear fuel assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Canaan, R.E.

    1995-12-01

    Natural convection heat transfer is experimentally investigated in an enclosed horizontal rod bundle, which characterizes a spent nuclear fuel assembly during dry storage and/or transport conditions. The basic test section consists of a square array of sixty-four stainless steel tubular heaters enclosed within a water-cooled rectangular copper heat exchanger. The heaters are supplied with a uniform power generation per unit length while the surrounding enclosure is maintained at a uniform temperature. The test section resides within a vacuum/pressure chamber in order to subject the assembly to a range of pressure statepoints and various backfill gases. The objective of this experimental study is to obtain convection correlations which can be used in order to easily incorporate convective effects into analytical models of horizontal spent fuel systems, and also to investigate the physical nature of natural convection in enclosed horizontal rod bundles in general. The resulting data consist of: (1) measured temperatures within the assembly as a function of power, pressure, and backfill gas; (2) the relative radiative contribution for the range of observed temperatures; (3) correlations of convective Nusselt number and Rayleigh number for the rod bundle as a whole; and (4) correlations of convective Nusselt number as a function of Rayleigh number for individual rods within the array.

  16. Optimal Prandtl number for heat transfer in rotating Rayleigh-Benard convection

    CERN Document Server

    Stevens, Richard J A M; Lohse, Detlef

    2009-01-01

    Numerical data for the heat transfer as a function of the Prandtl (Pr) and Rossby (Ro) numbers in turbulent rotating Rayleigh-Benard convection are presented for Rayleigh number Ra = 10^8. When Ro is fixed the heat transfer enhancement with respect to the non-rotating value shows a maximum as function of Pr. This maximum is due to the reduced efficiency of Ekman pumping when Pr becomes too small or too large. When Pr becomes small, i.e. for large thermal diffusivity, the heat that is carried by the vertical vortices spreads out in the middle of the cell, and Ekman pumping thus becomes less efficient. For higher Pr the thermal boundary layers (BLs) are thinner than the kinetic BLs and therefore the Ekman vortices do not reach the thermal BL. This means that the fluid that is sucked into the vertical vortices is colder than for lower Pr which limits the efficiency of the upwards heat transfer.

  17. Heating-insensitive scale increase caused by convective precipitation

    Science.gov (United States)

    Haerter, Jan; Moseley, Christopher; Berg, Peter

    2017-04-01

    The origin of intense convective extremes and their unusual temperature dependence has recently challenged traditional thermodynamic arguments, based on the Clausius-Clapeyron relation. In a sequence of studies (Lenderink and v. Mejgaard, Nat Geosc, 2008; Berg, Haerter, Moseley, Nat Geosc, 2013; and Moseley, Hohenegger, Berg, Haerter, Nat Geosc, 2016) the argument of convective-type precipitation overcoming the 7%/K increase in extremes by dynamical, rather than thermodynamic, processes has been promoted. How can the role of dynamical processes be approached for precipitating convective cloud? One-phase, non-precipitating Rayleigh-Bénard convection is a classical problem in complex systems science. When a fluid between two horizontal plates is sufficiently heated from below, convective rolls spontaneously form. In shallow, non-precipitating atmospheric convection, rolls are also known to form under specific conditions, with horizontal scales roughly proportional to the boundary layer height. Here we explore within idealized large-eddy simulations, how the scale of convection is modified, when precipitation sets in and intensifies in the course of diurnal solar heating. Before onset of precipitation, Bénard cells with relatively constant diameter form, roughly on the scale of the atmospheric boundary layer. We find that the onset of precipitation then signals an approximately linear (in time) increase in horizontal scale. This scale increase progresses at a speed which is rather insensitive to changes in surface temperature or changes in the rate at which boundary conditions change, hinting at spatial characteristics, rather than temperature, as a possible control on spatial scales of convection. When exploring the depth of spatial correlations, we find that precipitation onset causes a sudden disruption of order and a subsequent complete disintegration of organization —until precipitation eventually ceases. Returning to the initial question of convective

  18. Forced convective heat transfer in curved diffusers

    Science.gov (United States)

    Rojas, J.; Whitelaw, J. H.; Yianneskis, M.

    1987-01-01

    Measurements of the velocity characteristics of the flows in two curved diffusers of rectangular cross section with C and S-shaped centerlines are presented and related to measurements of wall heat transfer coefficients along the heated flat walls of the ducts. The velocity results were obtained by laser-Doppler anemometry in a water tunnel and the heat transfer results by liquid crystal thermography in a wind tunnel. The thermographic technique allowed the rapid and inexpensive measurement of wall heat transfer coefficients along flat walls of arbitrary boundary shapes with an accuracy of about 5 percent. The results show that an increase in secondary flow velocities near the heated wall causes an increase in the local wall heat transfer coefficient, and quantify the variation for maximum secondary-flow velocities in a range from 1.5 to 17 percent of the bulk flow velocity.

  19. Random Taylor hypothesis and the behavior of local and convective accelerations in isotropic turbulence

    NARCIS (Netherlands)

    Tsinober, A.; Vedula, P.; Yeung, P.K.

    2001-01-01

    The properties of acceleration fluctuations in isotropic turbulence are studied in direct numerical simulations (DNS) by decomposing the acceleration as the sum of local and convective contributions (aL = ?u/?t and aC = u??u), or alternatively as the sum of irrotational and solenoidal contributions

  20. Effects of turbulence and heterogeneous emissions on photochemically active species in the convective boundary layer

    NARCIS (Netherlands)

    Krol, M.C.; Molemaker, M.J.; Vilu-Guerau, de J.

    2000-01-01

    Photochemistry is studied in a convective atmospheric boundary layer. The essential reactions that account for the ozone formation and depletion are included in the chemical mechanism which, as a consequence, contains a wide range of timescales. The turbulent reacting flow is modeled with a

  1. Effects of shear in the convective boundary layer: analysis of the turbulent kinetic energy budget

    NARCIS (Netherlands)

    Pino, D.; Vilà-Guerau de Arellano, J.

    2008-01-01

    Effects of convective and mechanical turbulence at the entrainment zone are studied through the use of systematic Large-Eddy Simulation (LES) experiments. Five LES experiments with different shear characteristics in the quasi-steady barotropic boundary layer were conducted by increasing the value of

  2. Turbulence statistics and energy budget in rotating Rayleigh-Bénard convection

    NARCIS (Netherlands)

    Kunnen, R.P.J.; Geurts, Bernardus J.; Clercx, H.J.H.

    The strongly-modified turbulence statistics of Rayleigh–Bénard convection subject to various rotation rates is addressed by numerical investigations. The flow is simulated in a domain with periodic boundary conditions in the horizontal directions, and confined vertically by parallel no-slip

  3. Numerical Study of Entropy Generation due to Coupled Laminar and Turbulent Mixed Convection and Thermal Radiation in an Enclosure Filled with a Semitransparent Medium

    Directory of Open Access Journals (Sweden)

    M. Goodarzi

    2014-01-01

    Full Text Available The effect of radiation on laminar and turbulent mixed convection heat transfer of a semitransparent medium in a square enclosure was studied numerically using the Finite Volume Method. A structured mesh and the SIMPLE algorithm were utilized to model the governing equations. Turbulence and radiation were modeled with the RNG k-ε model and Discrete Ordinates (DO model, respectively. For Richardson numbers ranging from 0.1 to 10, simulations were performed for Rayleigh numbers in laminar flow (104 and turbulent flow (108. The model predictions were validated against previous numerical studies and good agreement was observed. The simulated results indicate that for laminar and turbulent motion states, computing the radiation heat transfer significantly enhanced the Nusselt number (Nu as well as the heat transfer coefficient. Higher Richardson numbers did not noticeably affect the average Nusselt number and corresponding heat transfer rate. Besides, as expected, the heat transfer rate for the turbulent flow regime surpassed that in the laminar regime. The simulations additionally demonstrated that for a constant Richardson number, computing the radiation heat transfer majorly affected the heat transfer structure in the enclosure; however, its impact on the fluid flow structure was negligible.

  4. Turbulent flow regime in coiled tubes: local heat-transfer coefficient

    Science.gov (United States)

    Bozzoli, F.; Cattani, L.; Mocerino, A.; Rainieri, S.

    2017-08-01

    Wall curvature represents a widely adopted technique for enhancing heat transfer: the fluid flowing inside a coiled pipe experiences the centrifugal force and this phenomenon induces local maxima in the velocity distribution that locally increase the temperature gradients at the wall by enhancing the heat transfer both in the laminar and in the turbulent flow regime. Consequently, the distribution of the velocity field over the cross-section of the tube is strongly uneven thus leading to significant variations along the circumferential angular coordinate of the convective heat-transfer coefficient at the wall internal surface: in particular, it shows higher values at the outer bend side of the coil than at the inner bend side. The aim of the present work is to estimate experimentally the local convective heat-transfer coefficient at the fluid wall interface in coiled tubes when turbulent flow regime occurs. In particular, the temperature distribution maps on the external coil wall are employed as input data of the inverse heat conduction problem in the wall and a solution approach based on the Tikhonov regularisation is implemented. The results, obtained with water as working fluid, are focused on the fully developed region in the turbulent flow regime in the Reynolds number range of 5000 to 12,000. For the sake of completeness, the overall efficiency of the coiled tubes under test is assessed under a first-law performance evaluation criterion.

  5. Intensification of Convective Heat Transfer in Heating Device of Mobile Heating System with BH-Heat Generator

    Directory of Open Access Journals (Sweden)

    N. A. Nesenchuk

    2013-01-01

    Full Text Available Directions pertaining to intensification of convective heat transfer in a soft heating device have been experimentally investigated  in the paper and the most efficient one has been selected that is creation of artificial roughness on the device surface. The considered heating device for a heat supply system of a mobile object has been made of soft polymer material (polyvinyl chloride. Following  evaluation results of  heat exchange intensification a criteria equation has been obtained for calculation of external heat transfer with due account of heat transfer intensification.

  6. Solar seismology. II - The stochastic excitation of the solar p-modes by turbulent convection

    Science.gov (United States)

    Goldreich, P.; Keeley, D. A.

    1977-01-01

    We test the hypothesis that the solar p-modes are stabilized by damping due to turbulent viscosity in the convective zone. Starting from the assumption that the modes are stable, we calculate expectation values for the modal energies. We find that the interaction between a p-mode and the turbulent convection is such that the modal energy tends toward equipartition with the kinetic energy of turbulent eddies whose lifetimes are comparable to the modal period. From the calculated values of the modal energies, we compute rms surface velocity amplitudes. Our predicted rms surface velocities range from 0.01 cm/sec for the fundamental radial mode to 0.6 cm/sec for the radial mode whose period is approximately 5 minutes. The predicted surface velocities for the low order p-modes are much smaller than the velocities inferred from recent observations.

  7. Heat convection at the density maximum point of water

    Science.gov (United States)

    Balta, Nuri; Korganci, Nuri

    2018-01-01

    Water exhibits a maximum in density at normal pressure at around 4° degree temperature. This paper demonstrates that during cooling, at around 4 °C, the temperature remains constant for a while because of heat exchange associated with convective currents inside the water. Superficial approach implies it as a new anomaly of water, but actually it is not.

  8. Estimation of convection heat and mass transfer coefficients for ...

    African Journals Online (AJOL)

    Estimation of convection heat and mass transfer coefficients for constant-rate drying period during tape casting. Y T Puyate. Abstract. No Abstract. Global Journal of Engineering Research Vol. 6 (1) 2007: pp. 75-77. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.

  9. Measurement of the Convective Heat-Transfer Coefficient

    Science.gov (United States)

    Conti, Rosaria; Gallitto, Aurelio Agliolo; Fiordilino, Emilio

    2014-01-01

    We propose an experiment for investigating how objects cool down toward the thermal equilibrium with their surroundings. We describe the time dependence of the temperature difference of the cooling objects and the environment with an exponential decay function. By measuring the thermal constant t, we determine the convective heat-transfer…

  10. Heat Convection at the Density Maximum Point of Water

    Science.gov (United States)

    Balta, Nuri; Korganci, Nuri

    2018-01-01

    Water exhibits a maximum in density at normal pressure at around 4° degree temperature. This paper demonstrates that during cooling, at around 4 °C, the temperature remains constant for a while because of heat exchange associated with convective currents inside the water. Superficial approach implies it as a new anomaly of water, but actually it…

  11. Predicting transition ranges to fully turbulent viscous boundary layers in low Prandtl number convection flows

    Science.gov (United States)

    Scheel, Janet D.; Schumacher, Jörg

    2017-12-01

    We discuss two aspects of turbulent Rayleigh-Bénard convection (RBC) on the basis of high-resolution direct numerical simulations in a unique setting: a closed cylindrical cell of aspect ratio of one. First, we present a comprehensive comparison of statistical quantities such as energy dissipation rates and boundary layer thickness scales. Data are used from three simulation run series at Prandtl numbers Pr that cover two orders of magnitude. In contrast to most previous studies in RBC the focus of the present work is on convective turbulence at very low Prandtl numbers including Pr=0.021 for liquid mercury or gallium and Pr=0.005 for liquid sodium. In this parameter range of RBC, inertial effects cause a dominating turbulent momentum transport that is in line with highly intermittent fluid turbulence both in the bulk and in the boundary layers and thus should be able to trigger a transition to the fully turbulent boundary layers of the ultimate regime of convection for higher Rayleigh number. Second, we predict the ranges of Rayleigh numbers for which the viscous boundary layer will transition to turbulence and the flow as a whole will cross over into the ultimate regime. These transition ranges are obtained by extrapolation from our simulation data. The extrapolation methods are based on the large-scale properties of the velocity profile. Two of the three methods predict similar ranges for the transition to ultimate convection when their uncertainties are taken into account. All three extrapolation methods indicate that the range of critical Rayleigh numbers Rac is shifted to smaller magnitudes as the Prandtl number becomes smaller.

  12. Non intrusive measurement of the convective heat transfer coefficient

    Energy Technology Data Exchange (ETDEWEB)

    Rebay, M.; Mebarki, G.; Padet, J. [Reims Univ., Reims (France). Faculty of Science, GRESPI Thermomechanical Lab; Arfaoui, A. [Reims Univ., Reims (France). Faculty of Science, GRESPI Thermomechanical Lab; Tunis Univ., Tunis (Tunisia). Faculty of Science, EL MANAR, LETTM; Maad, B.R. [Tunis Univ., Tunis (Tunisia). Faculty of Science, EL MANAR, LETTM

    2010-07-01

    The efficiency of cooling methods in thermal systems such as radiators and heat exchangers must be improved in order to enhance performance. The evaluation of the heat transfer coefficients between a solid and a fluid is necessary for the control and the dimensioning of thermal systems. In this study, the pulsed photothermal method was used to measure the convective heat transfer coefficient on a solid-fluid interface, notably between an air flow and a heated slab mounted on a PVC flat plate. This configuration simulated the electronic air-cooling inside enclosures and racks. The influence of the deflector's inclination angle on the enhancement of heat transfer was investigated using 2 newly developed identification models. The first model was based on a constant heat transfer coefficient during the pulsed experiment, while the second, improved model was based on a variable heat transfer coefficient. The heat transfer coefficient was deduced from the evolution of the transient temperature induced by a sudden deposit of a luminous energy on the front face of the slab. Temperature evolutions were derived by infrared thermography, a camera for cartography and a detector for precise measurement in specific locations. The results show the improvement of measurement accuracies when using a model that considers the temporal evolution of the convective heat transfer coefficient. The deflection of air flow on the upper surface of the heated slab demonstrated better cooling of the slab by the deflection of air flow. 11 refs., 1 tab., 8 figs.

  13. Relating Convective and Stratiform Rain to Latent Heating

    Science.gov (United States)

    Tao, Wei-Kuo; Lang, Stephen; Zeng, Xiping; Shige, Shoichi; Takayabu, Yukari

    2010-01-01

    The relationship among surface rainfall, its intensity, and its associated stratiform amount is established by examining observed precipitation data from the Tropical Rainfall Measuring Mission (TRMM) Precipitation Radar (PR). The results show that for moderate-high stratiform fractions, rain probabilities are strongly skewed toward light rain intensities. For convective-type rain, the peak probability of occurrence shifts to higher intensities but is still significantly skewed toward weaker rain rates. The main differences between the distributions for oceanic and continental rain are for heavily convective rain. The peak occurrence, as well as the tail of the distribution containing the extreme events, is shifted to higher intensities for continental rain. For rainy areas sampled at 0.58 horizontal resolution, the occurrence of conditional rain rates over 100 mm/day is significantly higher over land. Distributions of rain intensity versus stratiform fraction for simulated precipitation data obtained from cloud-resolving model (CRM) simulations are quite similar to those from the satellite, providing a basis for mapping simulated cloud quantities to the satellite observations. An improved convective-stratiform heating (CSH) algorithm is developed based on two sources of information: gridded rainfall quantities (i.e., the conditional intensity and the stratiform fraction) observed from the TRMM PR and synthetic cloud process data (i.e., latent heating, eddy heat flux convergence, and radiative heating/cooling) obtained from CRM simulations of convective cloud systems. The new CSH algorithm-derived heating has a noticeably different heating structure over both ocean and land regions compared to the previous CSH algorithm. Major differences between the new and old algorithms include a significant increase in the amount of low- and midlevel heating, a downward emphasis in the level of maximum cloud heating by about 1 km, and a larger variance between land and ocean in

  14. Computational Study of Convective Heat Transfer in Circular Pipe using Trapezoidal Ribs

    Science.gov (United States)

    Patel, V. K.; Sharma, P.; Saxena, K.

    2017-09-01

    Perturbations or interruptions provided in the passage of heat exchanger generate the vortices downstream. The formation of these natural vortices, augment local heat transfer abruptly. The effect on convective heat transfer enhancement and friction characteristics by providing trapezoidal ribs inside a circular pipe is computationally investigated in detail. Different variations of height, width and pitch of the ribs are used to optimize the rate of heat transfer through the pipe. Liquid water is employed as the working fluid. Input parameters of Reynolds Number ranging from 5000-60000 with axial flow along the pipe and constant heat flux of 50 W/cm2 to the pipe surface is used. After validation with the existing literature, Realizable k-ε turbulent model with enhanced wall function is used in commercial CFD software ANSYS FLUENT. The outcome of the investigation shows that the ribs provided on the inside of the pipe surface enhance the turbulence in the flow and produce recirculation which disturb the thermal boundary layer behind the ribs and thus help in enhancing the rate of heat transfer through the pipe.

  15. Turbulence and surface heat transfer near the stagnation point of a circular cylinder in turbulent flow

    Science.gov (United States)

    Wang, C. R.

    1983-01-01

    A turbulent boundary layer flow analysis of the momentum and thermal flow fields near the forward stagnation point due to a circular cylinder in turbulent cross flow is presented. Turbulence modeling length scale, anisotropic turbulence initial profiles and boundary conditions were identified as functions of the cross flow turbulence intensity and the boundary layer flow far field velocity. These parameters were used in a numerical computational procedure to calculate the mean velocity, mean temperature, and turbulence double correlation profiles within the flow field. The effects of the cross flow turbulence on the stagnation region momentum and thermal flow fields were investigated. This analysis predicted the existing measurements of the stagnation region mean velocity and surface heat transfer rate with cross flow Reynolds number and turbulence intensity less than 250,000 and 0.05, respectively.

  16. Numerical Study of Single Phase/Two-Phase Models for Nanofluid Forced Convection and Pressure Drop in a Turbulence Pipe Flow

    Directory of Open Access Journals (Sweden)

    M. Esfandiary

    2016-01-01

    Full Text Available In this paper, the problem of turbulent forced convection flow of water- alumina nanofluid in a uniformly heated pipe has been thoroughly investigated. In numerical study, single and two-phase models have been used. In single-phase modeling of nanofluid, thermal and flow properties of nanofluid have been considered to be dependent on temperature and volume fraction. Effects of volume fraction and Reynolds number (3000

  17. Endwall convective heat transfer for bluff bodies

    DEFF Research Database (Denmark)

    Wang, Lei; Salewski, Mirko; Sundén, Bengt

    2012-01-01

    The endwall heat transfer characteristics of forced flow past bluff bodies have been investigated using liquid crystal thermography (LCT). The bluff body is placed in a rectangular channel with both its ends attached to the endwalls. The Reynolds number varies from 50,000 to 100,000. In this stud...

  18. Conjugate problems in convective heat transfer

    CERN Document Server

    Dorfman, Abram S

    2009-01-01

    The conjugate heat transfer (CHT) problem takes into account the thermal interaction between a body and fluid flowing over or through it, a key consideration in both mechanical and aerospace engineering. Presenting more than 100 solutions of non-isothermal and CHT problems, this title considers the approximate solutions of CHT problems.

  19. ESTIMATION OF TURBULENT DIFFUSIVITY WITH DIRECT NUMERICAL SIMULATION OF STELLAR CONVECTION

    Energy Technology Data Exchange (ETDEWEB)

    Hotta, H.; Iida, Y.; Yokoyama, T., E-mail: hotta.h@eps.s.u-tokyo.ac.jp [Department of Earth and Planetary Science, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan)

    2012-05-20

    We investigate the value of horizontal turbulent diffusivity {eta} by numerical calculation of thermal convection. In this study, we introduce a new method whereby the turbulent diffusivity is estimated by monitoring the time development of the passive scalar, which is initially distributed in a given Gaussian function with a spatial scale d{sub 0}. Our conclusions are as follows: (1) assuming the relation {eta} = L{sub c} v{sub rms}/3, where v{sub rms} is the root-mean-square (rms) velocity, the characteristic length L{sub c} is restricted by the shortest one among the pressure (density) scale height and the region depth. (2) The value of turbulent diffusivity becomes greater with the larger initial distribution scale d{sub 0}. (3) The approximation of turbulent diffusion holds better when the ratio of the initial distribution scale d{sub 0} to the characteristic length L{sub c} is larger.

  20. Second Law Analysis in Convective Heat and Mass Transfer

    Directory of Open Access Journals (Sweden)

    A. Ben Brahim

    2006-02-01

    Full Text Available This paper reports the numerical determination of the entropy generation due to heat transfer, mass transfer and fluid friction in steady state for laminar double diffusive convection, in an inclined enclosure with heat and mass diffusive walls, by solving numerically the mass, momentum, species conservation and energy balance equations, using a Control Volume Finite-Element Method. The influences of the inclination angle, the thermal Grashof number and the buoyancy ratio on total entropy generation were investigated. The irreversibilities localization due to heat transfer, mass transfer and fluid friction is discussed for three inclination angles at a fixed thermal Grashof number.

  1. Lattice Boltzmann simulations of convection heat transfer in porous media

    Science.gov (United States)

    Liu, Qing; He, Ya-Ling

    2017-01-01

    A non-orthogonal multiple-relaxation-time (MRT) lattice Boltzmann (LB) method is developed to study convection heat transfer in porous media at the representative elementary volume scale based on the generalized non-Darcy model. In the method, two different LB models are constructed: one is constructed in the framework of the double-distribution-function approach, and the other is constructed in the framework of the hybrid approach. In particular, the transformation matrices used in the MRT-LB models are non-orthogonal matrices. The present method is applied to study mixed convection flow in a porous channel and natural convection flow in a porous cavity. It is found that the numerical results are in good agreement with the analytical solutions and/or other results reported in previous studies. Furthermore, the non-orthogonal MRT-LB method shows better numerical stability in comparison with the BGK-LB method.

  2. Enhancing Convective Heat Transfer over a Surrogate Photovoltaic Panel

    Science.gov (United States)

    Fouladi, Fama

    This research is particularly focused on studying heat transfer enhancement of a photovoltaic (PV) panel by putting an obstacle at the panel's windward edge. The heat transfer enhancement is performed by disturbing the airflow over the surface and increasing the heat and momentum transfer. Different objects such as triangular, square, rectangular, and discrete rectangular ribs and partial grids were applied at the leading edge of a surrogate PV panel and flow and the heat transfer of the panel are investigated experimentally. This approach was selected to expand understanding of effect of these different objects on the flow and turbulence structures over a flat surface by analyzing the flow comprehensively. It is observed that, a transverse object at the plate's leading edge would cause some flow blockage in the streamwise direction, but at the same time creates some velocity in the normal and cross stream directions. In addition to that, the obstacle generates some turbulence over the surface which persists for a long downstream distance. Also, among all studied objects, discrete rectangular ribs demonstrate the highest heat transfer rate enhancement (maximum Nu/Nu0 of 1.5). However, ribs with larger gap ratios are observed to be more effective at enhancing the heat transfer augmentation at closer distances to the rib, while at larger downstream distances from the rib, discrete ribs with smaller gap ratios are more effective. Furthermore, this work attempted to recognize the most influential flow parameters on the heat transfer enhancement of the surface. It is seen that the flow structure over a surface downstream of an object (flow separation-reattachment behaviour) has a significant effect on the heat transfer enhancement trend. Also, turbulence intensities are the most dominant parameters in enhancing the heat transfer rate from the surface; however, flow velocity (mostly normal velocity) is also an important factor.

  3. Convective heat transfer in ribbed channels with a 180 turn

    Energy Technology Data Exchange (ETDEWEB)

    Astarita, T.; Cardone, G.; Carlomagno, G.M. [University of Naples Federico II, DETEC, P. le Tecchio, 80-80125 Naples (Italy)

    2002-07-01

    Detailed quantitative maps of the heat transfer distribution near a 180 sharp turn of a square channel with rib turbulators are measured by means of infrared thermography associated with the heated-thin-foil technique. Air flows into the channel where ribs are mounted on two opposite walls and placed at 60 with respect to its axis. Two rib pitches, two different rib arrangements and two heating conditions are investigated. Results are presented in terms of local and averaged Nusselt numbers which are normalized with the classical Dittus and Boelter correlation for three different Reynolds numbers. (orig.)

  4. From convection rolls to finger convection in double-diffusive turbulence

    NARCIS (Netherlands)

    Yang, Yantao; Verzicco, Roberto; Lohse, Detlef

    2015-01-01

    Double-diffusive convection (DDC), which is the buoyancy-driven flow with fluid density depending on two scalar components, is ubiquitous in many natural and engineering environments. Of great interests are scalars’ transfer rate and flow structures. Here we systematically investigate DDC flow

  5. Stagnation Region Heat Transfer Augmentation at Very High Turbulence Levels

    Energy Technology Data Exchange (ETDEWEB)

    Ames, Forrest [University of North Dakota; Kingery, Joseph E. [University of North Dakota

    2015-06-17

    A database for stagnation region heat transfer has been extended to include heat transfer measurements acquired downstream from a new high intensity turbulence generator. This work was motivated by gas turbine industry heat transfer designers who deal with heat transfer environments with increasing Reynolds numbers and very high turbulence levels. The new mock aero-combustor turbulence generator produces turbulence levels which average 17.4%, which is 37% higher than the older turbulence generator. The increased level of turbulence is caused by the reduced contraction ratio from the liner to the exit. Heat transfer measurements were acquired on two large cylindrical leading edge test surfaces having a four to one range in leading edge diameter (40.64 cm and 10.16 cm). Gandvarapu and Ames [1] previously acquired heat transfer measurements for six turbulence conditions including three grid conditions, two lower turbulence aero-combustor conditions, and a low turbulence condition. The data are documented and tabulated for an eight to one range in Reynolds numbers for each test surface with Reynolds numbers ranging from 62,500 to 500,000 for the large leading edge and 15,625 to 125,000 for the smaller leading edge. The data show augmentation levels of up to 136% in the stagnation region for the large leading edge. This heat transfer rate is an increase over the previous aero-combustor turbulence generator which had augmentation levels up to 110%. Note, the rate of increase in heat transfer augmentation decreases for the large cylindrical leading edge inferring only a limited level of turbulence intensification in the stagnation region. The smaller cylindrical leading edge shows more consistency with earlier stagnation region heat transfer results correlated on the TRL (Turbulence, Reynolds number, Length scale) parameter. The downstream regions of both test surfaces continue to accelerate the flow but at a much lower rate than the leading edge. Bypass transition occurs

  6. Robust Controller for Turbulent and Convective Boundary Layers

    National Research Council Canada - National Science Library

    Speyer, Jason L; Kim, J. John

    2006-01-01

    Linear feedback controllers and estimators have been designed from the governing equations of a channel flow, linearized about the laminar mean flow, and a layer of heated fluid, linearized about the no-motion state...

  7. Convective heat transfer in engine coolers influenced by electromagnetic fields

    Science.gov (United States)

    Karcher, C.; Kühndel, J.

    2017-08-01

    In engine coolers of off-highway vehicles, convective heat transfer at the coolant side limits both efficiency and performance density of the apparatus. Here, due to restrictions in construction and design, backwater areas and stagnation regions cannot be avoided. Those unwanted changes in flow characteristics are mainly triggered by flow deflections and sudden cross-sectional expansions. In application, mixtures of water and glysantine are used as appropriate coolants. Such coolants typically show an electrical conductivity of a few S/m. Coolant flow and convective heat transfer can then be controlled using Lorentz forces. These body forces are generated within the conducting fluid by the interactions of an electrical current density and a localized magnetic field, both of which are externally superimposed. In future application, this could be achieved by inserting electrodes in the cooler wall and a corresponding arrangement of permanent magnets. In this paper we perform numerical simulations of such magnetohydrodynamic flow in three model geometries that frequently appear in engine cooling applications: Carnot-Borda diffusor, 90° bend, and 180° bend. The simulations are carried out using the software package ANSYS Fluent. The present study demonstrates that, depending on the electromagnetic interaction parameter and the specific geometric arrangement of electrodes and magnetic field, Lorentz forces are suitable to break up eddy waters and separation zones and thus significantly increase convective heat transfer in these areas. Furthermore, the results show that hydraulic pressure losses can be reduced due to the pumping action of the Lorentz forces.

  8. Mathematical modeling of radiant heating of a closed rectangular area under conditions of convective heat transfer at the external boundaries

    Directory of Open Access Journals (Sweden)

    Nee Alexander

    2015-01-01

    Full Text Available Mathematical modeling of radiant heating of a closed rectangular area under conditions of convective heat transfer at the external boundaries is passed. The fields of temperature and stream function, illustrating the unsteady nature of the heat transfer were obtained. The extent influence of convective heat transfer at the external boundaries on the circulating flows formation in the gas cavity are shown.

  9. Quantitative Temperature Imaging in Gas-Phase Turbulent Thermal Convection by Laser-Induced Fluorescence of Acetone

    Energy Technology Data Exchange (ETDEWEB)

    KEARNEY,SEAN P.; REYES,FELIPE V.

    2000-12-13

    In this paper, an acetone planar laser-induced fluorescence (PLIF) technique for nonintrusive, temperature imaging is demonstrated in gas-phase (Pr = 0.72) turbulent Rayleigh-Benard convection at Rayleigh number, Ra = 1.3 x 10{sup 5}. The PLIF technique provides quantitative, spatially correlated temperature data without the flow intrusion or time lag associated with physical probes and without the significant path averaging that plagues most optical heat-transfer diagnostic tools, such as the Mach-Zehnder interferometer, thus making PLIF an attractive choice for quantitative thermal imaging in easily perturbed, complex three-dimensional flow fields. The instantaneous (20-ns integration time) thermal images presented have a spatial resolution of 176 x 176 x 500 {micro}m and a single-pulse temperature measurement precision of {+-}5.5 K, or 5.4 % of the total temperature difference. These images represent a 2-D slice through a complex, 3-D flow allowing for the thermal structure of the turbulence to be quantified. Statistics such as the horizontally averaged temperature profile, rms temperature fluctuation, two-point spatial correlations, and conditionally averaged plume structures are computed from an ensemble of 100 temperature images. The profiles of the mean temperature and rms temperature fluctuation are in good agreement with previously published data, and the results obtained from the two-point spatial correlations and conditionally averaged temperature fields show the importance of large-scale coherent structures in this turbulent flow.

  10. Geostrophic convective turbulence: The effect of boundary layers

    CERN Document Server

    Ostilla-Mónico, Rodolfo; Kunnen, Rudie P J; Verzicco, Roberto; Lohse, Detlef

    2014-01-01

    This Letter presents results of the first direct numerical simulations of rotating Rayleigh--B\\'enard convection in the so-called geostrophic regime, (hence very small Ekman numbers $\\mathcal{O}(10^{-7})$ and high Rayleigh numbers~$Ra=10^{10}$ and~$5\\cdot 10^{10}$), employing the \\emph{full} Navier--Stokes equations. In the geostrophic regime the criteria of very strong rotation and large supercriticality are met simultaneously, which is true for many geophysical and astrophysical flows. Until now, numerical approaches of this regime have been based on \\emph{reduced} versions of the Navier--Stokes equations (cf. Sprague \\emph{et al.} J. Fluid Mech., \\textbf{551}, 141 (2006)), omitting the effect of the viscous (Ekman) boundary layers. By using different velocity boundary conditions at the plates, we study the effect of these Ekman layers. We find that the formation of large-scale structures (Rubio \\emph{et al.} (Phys. Rev. Lett. \\textbf{112} (2014)), which indicates the presence of an inverse energy cascade, ...

  11. Comparative study of convective heat transfer characteristics of nanofluids

    Science.gov (United States)

    Muryam, Hina; Ramzan, Naveed; Umer, Asim; Awan, Gul Hameed; Hassan, Ali

    2017-07-01

    The present research is about to draw a comparison between heat transfer characteristics of gold/deionized water (DIW) and silver/DIW based nanofluid under same heat flux for laminar flow. Experiments are performed on both nanofluid by using different concentrations (0.015, 0.045, 0.0667%) of nano-particles (NPs) in DIW as a base fluid. The experimental study concludes that an appreciable intensification in heat transfer coefficient (HTC) of both nanofluid has been attained as compare to base fluid. However, gold/DIW based nanofluid exhibit better convective heat transfer intensification compared with silver/DIW based nanofluid but Shah correlation cannot predict as much augmentation as in experimental work for both nanofluid. It is also noticed that the anomalous enhancement in Nusselt number and HTC is not only due to the accession in thermal properties but also by the formation of thinner thermal boundary layer at the entrance of the tube due to NPs.

  12. Heat Transport in Low-Rossby-Number Rayleigh-Bénard Convection

    Science.gov (United States)

    Julien, Keith; Knobloch, Edgar; Rubio, Antonio M.; Vasil, Geoffrey M.

    2012-12-01

    We demonstrate, via simulations of asymptotically reduced equations describing rotationally constrained Rayleigh-Bénard convection, that the efficiency of turbulent motion in the fluid bulk limits overall heat transport and determines the scaling of the nondimensional Nusselt number Nu with the Rayleigh number Ra, the Ekman number E, and the Prandtl number σ. For E≪1 inviscid scaling theory predicts and simulations confirm the large Ra scaling law Nu-1≈C1σ-1/2Ra3/2E2, where C1 is a constant, estimated as C1≈0.04±0.0025. In contrast, the corresponding result for nonrotating convection, Nu-1≈C2Raα, is determined by the efficiency of the thermal boundary layers (laminar: 0.28≲α≲0.31, turbulent: α˜0.38). The 3/2 scaling law breaks down at Rayleigh numbers at which the thermal boundary layer loses rotational constraint, i.e., when the local Rossby number ≈1. The breakdown takes place while the bulk Rossby number is still small and results in a gradual transition to the nonrotating scaling law. For low Ekman numbers the location of this transition is independent of the mechanical boundary conditions.

  13. Convective heat transfer on an inlet guide vane.

    Science.gov (United States)

    Holmer, M L; Eriksson, L E; Sunden, B

    2001-05-01

    The flow and temperature fields around an inlet guide vane are determined numerically by a CFD method. Outer surface temperatures, heat transfer coefficient distributions, and static pressure distributions are presented. Three different thermal boundary conditions on the vane are analysed. The computed results are compared with experimental data. The governing equations are solved by a finite-volume method with the low Reynolds number version of the k-omega turbulence model by Wilcox implemented. It is found that the calculated results agree best with measurements if a conjugate heat transfer approach is applied and thus this wall condition is recommended for future investigations of film cooling of guide vanes and turbine blades.

  14. Thermal measurements and flow visualization of heat convection in a tilted channel

    Science.gov (United States)

    Tisserand, Jean-Christophe; Creyssels, Mathieu; Riedinger, Xavier; Castaing, Bernard; Chillà, Francesca

    2010-05-01

    Convection is the most important heat transport mechanism. We can find it not only in many natural situations such as stars, planet's atmosphere but also in half-natural situations such as industrial plants. Furthermore, the Rayleigh-Benard system, in which a fluid is cooled from above and heated from below, is one of the most studied systems in thermal convection. Nevertheless, in this configuration, the neighborhood of the plates controls the heat transfer. Therefore, we have to make a system in which the flow forgets the cold and the hot plate. We have built a vertical long channel which links two chambers : the hot one at the lower end and the cold one at the upper end. Moreover, this channel, which is hanged to a structure, can be tilted from an angle of 0 degree to 90 degrees. The experimental facility used for this purpose is a square channel with an inner area of 5*5 cm² m and with a height of 20 cm. The cell is filled with water and is heated at the bottom by Joule effect. At the top, the temperature is regulated by a thermal bath and the mean temperature of the bulk is 25°C . It is worth noticing that this configuration could correspond to heat pipes (without phase transformation) used in thermalisation systems or could model a vertical access pit of an underground carry. In this paper, we want to highlight how the thermal convection in the bulk of the channel is. In the first part, the paper will be focused on the visualization of the flow into the channel thanks to particle image velocimetry (PIV) technique. We look at the mean velocity field (transverse and axial components) , the fluctuations of the mean velocity field and the shear Reynolds stress. Besides, we analyze how the influence of the power supply and the dependance of the tilt angle are. At last, we will interpret the PIV measurements in terms of turbulent viscosity and effective heat conduction and we will deduce from the PIV measurements the axial mean profile of temperature. Then, in a

  15. Reappraising the relationships between physics students’ mental models and predictions: An example of heat convection

    National Research Council Canada - National Science Library

    Chiou, Guo-Li

    2013-01-01

    .... The purpose of this study, therefore, was first to investigate 30 physics students’ mental models of heat convection, and then to examine the relationship between their mental models and predictions of convection-related phenomena...

  16. A new method to optimize natural convection heat sinks

    Science.gov (United States)

    Lampio, K.; Karvinen, R.

    2017-08-01

    The performance of a heat sink cooled by natural convection is strongly affected by its geometry, because buoyancy creates flow. Our model utilizes analytical results of forced flow and convection, and only conduction in a solid, i.e., the base plate and fins, is solved numerically. Sufficient accuracy for calculating maximum temperatures in practical applications is proved by comparing the results of our model with some simple analytical and computational fluid dynamics (CFD) solutions. An essential advantage of our model is that it cuts down on calculation CPU time by many orders of magnitude compared with CFD. The shorter calculation time makes our model well suited for multi-objective optimization, which is the best choice for improving heat sink geometry, because many geometrical parameters with opposite effects influence the thermal behavior. In multi-objective optimization, optimal locations of components and optimal dimensions of the fin array can be found by simultaneously minimizing the heat sink maximum temperature, size, and mass. This paper presents the principles of the particle swarm optimization (PSO) algorithm and applies it as a basis for optimizing existing heat sinks.

  17. CONVECTIVE HEAT TRANSFER IN CYCLONE DEVICE WITH EXTERNAL GAS RECIRCULATION

    Directory of Open Access Journals (Sweden)

    S. V. Karpov

    2016-01-01

    Full Text Available The article considers the convective heat transfer on the surface of a hollow cylinder or several billets in a cyclone device with the new principle of external gas recirculation. According to this principle, transport of coolant from the lateral surface of the chamber, where the temperature is the highest, in the axial region is being fulfilled due to the pressure drop between the wall and axial areas of cyclonic flow. Dependency analysis of average and local heat transfer coefficients from operational and geometrical parameters has been performed; the generalized similarity equations for the calculation of the latter have been suggested. It is demonstrated that in case of download of a cyclone chamber with several billets, the use of the considered scheme of the external recirculation due to the specific characteristics of aerodynamics practically does not lead to noticeable changes in the intensity of convective heat transfer. Both experimental data and the numerical simulation results obtained with the use of OpenFOAM platform were used in the work. The investigations fulfilled will expand the area of the use of cyclone heating devices.

  18. The Characterization of Atmospheric Boundary Layer Depth and Turbulence in a Mixed Rural and Urban Convective Environment

    Science.gov (United States)

    Hicks, Micheal M.

    A comprehensive analysis of surface-atmosphere flux exchanges over a mixed rural and urban convective environment is conducted at Howard University Beltsville, MD Research Campus. This heterogeneous site consists of rural, suburban and industrial surface covers to its south, east and west, within a 2 km radius of a flux sensor. The eddy covariance method is utilized to estimate surface-atmosphere flux exchanges of momentum, heat and moisture. The attributes of these surface flux exchanges are contrasted to those of classical homogeneous sites and assessed for accuracy, to evaluate the following: (I) their similarity to conventional convective boundary layer (CBL) processes and (II) their representativeness of the surrounding environment's turbulent properties. Both evaluations are performed as a function of upwind surface conditions. In particular, the flux estimates' obedience to spectrum power laws and similarity theory relationships is used for performing the first evaluation, and their ability to close the surface energy balance and accurately model CBL heights is used for the latter. An algorithm that estimates atmospheric boundary layer heights from observed lidar extinction backscatter was developed, tested and applied in this study. The derived lidar based CBL heights compared well with those derived from balloon borne soundings, with an overall Pearson correlation coefficient and standard deviation of 0.85 and 223 m, respectively. This algorithm assisted in the evaluation of the response of CBL processes to surface heterogeneity, by deriving high temporal CBL heights and using them as independent references of the surrounding area averaged sensible heat fluxes. This study found that the heterogeneous site under evaluation was rougher than classical homogeneous sites, with slower dissipation rates of turbulent kinetic energy. Flux measurements downwind of the industrial complexes exhibited enhanced efficiency in surface-atmosphere momentum, heat, and

  19. Natural convection of ferrofluids in partially heated square enclosures

    Energy Technology Data Exchange (ETDEWEB)

    Selimefendigil, Fatih, E-mail: fatih.selimefendigil@cbu.edu.tr [Department of Mechanical Engineering, Celal Bayar University, 45140 Manisa (Turkey); Öztop, Hakan F., E-mail: hfoztop1@gmail.com [Department of Mechanical Engineering, Technology Faculty, Fırat University, 23119 Elazığ (Turkey); Al-Salem, Khaled, E-mail: kalsalem@ksu.edu.sa [Department of Mechanical Engineering, College of Engineering, King Saud University, Riyadh (Saudi Arabia)

    2014-12-15

    In this study, natural convection of ferrofluid in a partially heated square cavity is numerically investigated. The heater is located to the left vertical wall and the right vertical wall is kept at constant temperature lower than that of the heater. Other walls of the square enclosure are assumed to be adiabatic. Finite element method is utilized to solve the governing equations. The influence of the Rayleigh number (10{sup 4}≤Ra≤5×10{sup 5}), heater location (0.25H≤y{sub h}≤0.75H), strength of the magnetic dipole (0≤γ≤2), horizontal and vertical location of the magnetic dipole (−2H≤a≤−0.5H, 0.2H≤b≤0.8H) on the fluid flow and heat transfer characteristics are investigated. It is observed that different velocity components within the square cavity are sensitive to the magnetic dipole source strength and its position. The length and size of the recirculation zones adjacent to the heater can be controlled with magnetic dipole strength. Averaged heat transfer increases with decreasing values of horizontal position of the magnetic dipole source. Averaged heat transfer value increases from middle towards both ends of the vertical wall when the vertical location of the dipole source is varied. When the heater location is changed, a symmetrical behavior in the averaged heat transfer plot is observed and the minimum value of the averaged heat transfer is attained when the heater is located at the mid of vertical wall. - Highlights: • Free convection of ferrofluids in a partially heated cavity is numerically studied. • Velocities are sensitive to the magnetic dipole source strength and its position. • Averaged Nu increases with decreasing x-location values of the magnetic dipole. • Averaged Nu increases from middle towards ends when y-location of dipole changes.

  20. Performance of a convective, infrared and combined infrared- convective heated conveyor-belt dryer.

    Science.gov (United States)

    El-Mesery, Hany S; Mwithiga, Gikuru

    2015-05-01

    A conveyor-belt dryer was developed using a combined infrared and hot air heating system that can be used in the drying of fruits and vegetables. The drying system having two chambers was fitted with infrared radiation heaters and through-flow hot air was provided from a convective heating system. The system was designed to operate under either infrared radiation and cold air (IR-CA) settings of 2000 W/m(2) with forced ambient air at 30 °C and air flow of 0.6 m/s or combined infrared and hot air convection (IR-HA) dryer setting with infrared intensity set at 2000 W/m(2) and hot at 60 °C being blown through the dryer at a velocity of 0.6 m/s or hot air convection (HA) at an air temperature of 60 °C and air flow velocity 0.6 m/s but without infrared heating. Apple slices dried under the different dryer settings were evaluated for quality and energy requirements. It was found that drying of apple (Golden Delicious) slices took place in the falling rate drying period and no constant rate period of drying was observed under any of the test conditions. The IR-HA setting was 57.5 and 39.1 % faster than IR-CA and HA setting, respectively. Specific energy consumption was lower and thermal efficiency was higher for the IR-HA setting when compared to both IR-CA and HA settings. The rehydration ratio, shrinkage and colour properties of apples dried under IR-HA conditions were better than for either IR-CA or HA.

  1. Free convection flow and heat transfer in pipe exposed to cooling

    Energy Technology Data Exchange (ETDEWEB)

    Mme, Uduak Akpan

    2010-10-15

    One of the challenges with thermal insulation design in subsea equipment is to minimize the heat loss through cold spots during production shut down. Cold spots are system components where insulation is difficult to implement, resulting in an insulation discontinuity which creates by nature a thermal bridge. It is difficult to avoid cold spots or thermal bridges in items like sensors, valves, connectors and supporting structures. These areas of reduced or no insulation are referred to as cold spots. Heat is drained faster through these spots, resulting in an increased local fluid density resulting in an internal fluid flow due to gravity and accelerated cool- down. This natural convection flow is important for both heat loss and internal distribution of the temperature. This thesis is presenting both experimental work and modelling work. A series of cool down tests and Computational Fluid Dynamics (CFD) simulations of these tests are presented. These tests and simulations were carried out in order to understand the flow physics involved in heat exchange processes caused by free convection flow in pipe exposed to cooling. Inclination of the pipe relative to the direction of gravity and temperature difference between cooling water and internal pipe water are the two main parameters investigated in this study. The experimental heat removal and temperature field is discussed and further interpreted by means of computational fluid dynamics. For prediction of the evolvement of the local temperature and heat flow, selection of an appropriate turbulence model is critical. Hence, different models and wall functions are investigated. The predicted temperature profiles and heat extraction rates are compered to the experiments for the selected turbulence models. Our main conclusions, supported by our experimental and CFD results, include: (i) Heat transfer from a localized cold spot in an inclined pipe is most efficient when the pipe orientation is close to horizontal. As the

  2. An experimental investigation of turbulent flow heat transfer through ...

    African Journals Online (AJOL)

    An experimental investigation has been carried out to study the turbulent flow heat transfer and to determine the pressure drop characteristics of air, flowing through a tube with insert. An insert of special geometry is used inside the tube. The test section is electrically heated, and air is allowed to flow as the working fluid ...

  3. The Role of the Velocity Gradient in Laminar Convective Heat Transfer through a Tube with a Uniform Wall Heat Flux

    Science.gov (United States)

    Wang, Liang-Bi; Zhang, Qiang; Li, Xiao-Xia

    2009-01-01

    This paper aims to contribute to a better understanding of convective heat transfer. For this purpose, the reason why thermal diffusivity should be placed before the Laplacian operator of the heat flux, and the role of the velocity gradient in convective heat transfer are analysed. The background to these analyses is that, when the energy…

  4. Intermittent heating of the solar corona by MHD turbulence

    Directory of Open Access Journals (Sweden)

    É. Buchlin

    2007-10-01

    Full Text Available As the dissipation mechanisms considered for the heating of the solar corona would be sufficiently efficient only in the presence of small scales, turbulence is thought to be a key player in the coronal heating processes: it allows indeed to transfer energy from the large scales to these small scales. While Direct numerical simulations which have been performed to investigate the properties of magnetohydrodynamic turbulence in the corona have provided interesting results, they are limited to small Reynolds numbers. We present here a model of coronal loop turbulence involving shell-models and Alfvén waves propagation, allowing the much faster computation of spectra and turbulence statistics at higher Reynolds numbers. We also present first results of the forward-modelling of spectroscopic observables in the UV.

  5. A survey on infrared thermography for convective heat transfer measurements

    Energy Technology Data Exchange (ETDEWEB)

    Astarita, T.; Cardone, G.; Carlomagno, G.M.; Meola, C. [Universita degli Studi di Napoli ' ' Federico II' ' (Italy). Dipartimento di Energetica

    2000-11-01

    During the past several years infrared thermography has evolved into a powerful investigative means, of thermo-fluid-dynamic analysis to measure convective heat fluxes as well as to investigate the surface flow field behaviour over complicated body shapes. The basic concepts that govern this innovative measurement technique together with some particular aspects linked to its use are herein reviewed. Different operating methods together with their implementations are also discussed. Finally, the capability of infrared thermography to deal with several simple, or complex, fluid flow configurations is analysed. (author)

  6. Study on the turbulence model sensitivity for various cross-corrugated surfaces applied to matrix type heat exchanger

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jun Myung; Ha, Man Yeong; Son, Chang Min; Doo, Jeong Hoon; Min, June Kee [Pusan National University, Busan (Korea, Republic of)

    2016-03-15

    Diverse cross-corrugated surface geometries were considered to estimate the sensitivity of four variants of k-ε turbulence models (Low Reynolds, standard, RNG and realizable models). The cross-corrugated surfaces considered in this study are a conventional sinusoidal shape and two different asymmetric shapes. The numerical simulations using the steady incompressible Reynolds-averaged Navier Stokes (RANS) equations were carried out to obtain the steady solutions of the flow and thermal fields in the unitary cell of the heat exchanger matrix. In addition, the experimental test for the measurement of local convective heat transfer coefficients on the heat transfer surfaces was performed by means of the Transient liquid crystal (TLC) technique in order to compare the numerical results with the measured data. The features on detailed flow structure and corresponding heat transfer in the unitary cell of the matrix type heat exchanger are compared and analyzed against four different turbulence models considered in this study.

  7. Experimental investigation of convective heat transfer agumentation using Al2O3/water nanofluid in circular pipe

    Science.gov (United States)

    Chavan, Durgeshkumar; Pise, Ashok T.

    2015-09-01

    In the present paper, experimental study is performed to investigate convective heat transfer and flow characteristics of nanofluids through a circular tube. The heat transfer coefficient and friction factor of the γ-Al2O3-water nanofluid flowing through a pipe of 10 mm inner ID and 1 m in length, with constant wall temperature under turbulent flow conditions are investigated. Experiments are conducted with 30 nm size γ-Al2O3 nanoparticle with a volume fraction between 0.1 and to 1.0 and Reynolds number between 8,000 and 14,000. Experimental results emphasize the heat transfer enhancement with the increase in a Reynolds number or nanoparticle volume fraction. The maximum enhancement of 36 % in the heat transfer coefficient for a Reynolds number of 8,550, by using nanofluid with 1.0 vol% was observed compared with base fluid. Experimental measurement also shows the considerable increase in the pressure drop with small addition of nanoparticles in base fluid. Experimental results of nanofluids were compared with existing convective heat transfer correlations in the turbulent regime. Comparison shows that Maiga's correlation has close agreement with experimental results in comparison with Dittus Boelter correlation.

  8. Effect of turbulence and convection on melting of the ice shelves in stratified environment

    Science.gov (United States)

    Gayen, Bishakdatta; Mondal, Mainak; Griffiths, Ross

    2017-11-01

    We have performed high-resolution simulations to investigate the convective boundary layer when a wall of ice dissolves into stratified seawater under polar ocean conditions. Under the stratified ambient condition, melt water spreads out into the interior in a series of nearly horizontal layers due to double diffusive convection. The layer thickness depends on the ambient density gradient and the difference in density between the freezing point (interface temperature) and the ambient water temperature. For a small O(1) m hight box the layers are laminar and results for layer depth are in agreement with the experimental results. However, for significantly higher ice walls the layer scaling differs as a result of turbulent mixing. Stratification has a significant effect on melt rate which further helps in the shaping of ice-wall. The temperature and density structures found under Pine Island Glacier show several layers having a vertical scale that can also be explained by this study.

  9. Plume fragmentation by bulk interactions in turbulent Rayleigh-Bénard convection.

    Science.gov (United States)

    Bosbach, Johannes; Weiss, Stephan; Ahlers, Guenter

    2012-02-03

    Using compressed gases with Prandtl numbers near 0.7, we obtained flow visualizations of turbulent Rayleigh-Bénard convection in a cylindrical sample with an aspect ratio Γ≡D/L≅10 (D is the diameter and L the height) by the shadowgraph method. Focusing on the plumes under the top plate, we found that their length had a log-normal distribution, suggesting a fragmentation process. Fragmentation events could be visually identified in the images and involved plume interactions with bulk fluctuations or upwelling domain walls. We found the mean spacing between plumes to vary with the Rayleigh number in proportion to the volume-averaged Kolmogorov length of the turbulent bulk fluctuations, providing further evidence for plume-bulk interactions.

  10. Marangoni mixed convection flow with Joule heating and nonlinear radiation

    Directory of Open Access Journals (Sweden)

    Tasawar Hayat

    2015-07-01

    Full Text Available Marangoni mixed convective flow of Casson fluid in a thermally stratified medium is addressed. Flow analysis has been carried out in presence of inclined magnetic field. Heat transfer analysis is discussed in the presence of viscous dissipation, Joule heating and nonlinear thermal radiation. The governing nonlinear partial differential equations are first converted into ordinary differential systems and then developed the convergent series solutions. Flow pattern with the influence of pertinent parameters namely the magnetic parameter, Casson fluid parameter, temperature ratio parameter, stratification parameter, Prandtl number, Eckert number and radiation parameter is investigated. Expression of local Nusselt number is computed and analyzed. It is found that the Nusselt number decreases by increasing magnetic parameter, temperature ratio parameter, angle of inclination and stratification parameter. Moreover the effect of buoyancy parameter on the velocity distribution is opposite in both the opposing and assisting flow phenomena. Thermal field and associated layer thickness are enhanced for larger radiation parameter.

  11. Modelling of convective heat and mass transfer in rotating flows

    CERN Document Server

    Shevchuk, Igor V

    2016-01-01

     This monograph presents results of the analytical and numerical modeling of convective heat and mass transfer in different rotating flows caused by (i) system rotation, (ii) swirl flows due to swirl generators, and (iii) surface curvature in turns and bends. Volume forces (i.e. centrifugal and Coriolis forces), which influence the flow pattern, emerge in all of these rotating flows. The main part of this work deals with rotating flows caused by system rotation, which includes several rotating-disk configurations and straight pipes rotating about a parallel axis. Swirl flows are studied in some of the configurations mentioned above. Curvilinear flows are investigated in different geometries of two-pass ribbed and smooth channels with 180° bends. The author demonstrates that the complex phenomena of fluid flow and convective heat transfer in rotating flows can be successfully simulated using not only the universal CFD methodology, but in certain cases by means of the integral methods, self-similar and analyt...

  12. Identification of convective heat loss on exterior cavity wall assemblies

    Science.gov (United States)

    Colantonio, Antonio

    1999-03-01

    Most present day low and medium rise buildings constructed in Canada use some form of cavity wall design for their exterior walls. These types of wall assemblies use a broad range of cladding materials such as brick, stone, wood, sheet metal, porcelain enamel or metal panels, cementitious materials and plastics. The interior assemblies of these walls include the air barrier, vapor barrier and insulation layers. The cladding is separated from the interior wall assembly by an air space of varying thickness. Dependent upon the temperature differential between the interior and exterior, the temperature between the outer surface of the interior wall assembly and the inner surface of the exterior cladding under conditions in which air movement is restricted will give rise to convective heat loss mechanisms. This paper will look at how these convective heat loss patterns manifest themselves as thermal patterns on exterior surfaces of cladding materials. Similar details will be illustrated under various pressure differential conditions through the entire building envelope assembly. Various types of exterior wall assemblies will be discussed.

  13. Numerical prediction of flow, heat transfer, turbulence and combustion

    CERN Document Server

    Spalding, D Brian; Pollard, Andrew; Singhal, Ashok K

    1983-01-01

    Numerical Prediction of Flow, Heat Transfer, Turbulence and Combustion: Selected Works of Professor D. Brian Spalding focuses on the many contributions of Professor Spalding on thermodynamics. This compilation of his works is done to honor the professor on the occasion of his 60th birthday. Relatively, the works contained in this book are selected to highlight the genius of Professor Spalding in this field of interest. The book presents various research on combustion, heat transfer, turbulence, and flows. His thinking on separated flows paved the way for the multi-dimensional modeling of turbu

  14. Heat Transfer Enhancement in Turbulent Flows by Blocked Surfaces

    Directory of Open Access Journals (Sweden)

    Onur YEMENİCİ

    2013-04-01

    Full Text Available In this study, the heat transfer analyses over flat and blocked surfaces were carried out in turbulent flow under the influence of the block height. A constant-temperature hot wire anemometer was used to the velocity and turbulent intensity measurements, while temperature values were measured by copper-constantan thermocouples. The average Stanton numbers for block heights of 15 and 25 mm were higher than those of flat surface by %38 and %84, respectively. The results showed that the presence of the blocks increased the heat transfer and the enhancement rose with block heights

  15. Cryogenic Heat Exchanger with Turbulent Flows

    Science.gov (United States)

    Amrit, Jay; Douay, Christelle; Dubois, Francis; Defresne, Gerard

    2012-01-01

    An evaporator-type cryogenic heat exchanger is designed and built for introducing fluid-solid heat exchange phenomena to undergraduates in a practical and efficient way. The heat exchanger functions at liquid nitrogen temperature and enables cooling of N[subscript 2] and He gases from room temperatures. We present first the experimental results of…

  16. Numerical investigation on the convective heat transfer in a spiral coil with radiant heating

    Directory of Open Access Journals (Sweden)

    Đorđević Milan Lj.

    2016-01-01

    Full Text Available The objective of this study was to numerically investigate the heat transfer in spiral coil tube in the laminar, transitional, and turbulent flow regimes. The Archimedean spiral coil was exposed to radiant heating and should represent heat absorber of parabolic dish solar concentrator. Specific boundary conditions represent the uniqueness of this study, since the heat flux upon the tube external surfaces varies not only in the circumferential direction, but also in the axial direction. The curvature ratio of spiral coil varies from 0.029 at the flow inlet to 0.234 at the flow outlet, while the heat transfer fluid is water. The 3-D steady-state transport equations were solved using the Reynolds stress turbulence model. Results showed that secondary flows strongly affect the flow and that the heat transfer is strongly asymmetric, with higher values near the outer wall of spiral. Although overall turbulence levels were lower than in a straight pipe, heat transfer rates were larger due to the curvature-induced modifications of the mean flow and temperature fields. [Projekat Ministarstva nauke Republike Srbije, br. 42006

  17. The safety and effectiveness of a modified convection heating system for children during anesthesia.

    Science.gov (United States)

    Cassey, John G; Armstrong, Peter J; Smith, Gil E; Farrell, Patrick T

    2006-06-01

    Convection heating shows most promise in maintaining children's core temperatures under anesthesia. We have previously shown that a modified convection heating technique worked in a mannequin model and sought to establish its safety and effectiveness in a clinical study. Children were recruited who were having elective surgery under general anesthesia lasting >90 min. The children were anesthetized and maintained in a room temperature of 21 degrees C. Warming was performed by a 'Bair Hugger' attached to a heat dissipation box, producing turbulent air from multiple outlet holes on its face. A plastic sheet covered the child, was attached to the top of the box, tucked into the sides of the bed and left open at the head end. Temperatures at various sites (air, skin, and core) were continuously monitored using thermistors connected to a datalogger and laptop. Analysis was performed using Excel. The study comprised 40 children ranging in age from 2 days to 12.5 years and weigh 2.5-73 kg. Operations were 'peripheral' (e.g. urethroplasty) lasting 90 min to major laparotomy lasting 590 min. Body surface area uncovered was 5-25%. Skin temperatures rose to a maximum of c. 40 degrees C. Core temperatures rose after a 12-min lag by 0.01-0.04 degrees C x min(-1). In children who became hyperthermic, cooling was readily achieved by turning the heating off and leaving the fan running. The technique is safe and effective for children throughout the pediatric range. The practice of increasing room temperature above 21 degrees C for elective cases should be abandoned. Continuous monitoring of core temperature is necessary to prevent hyperthermia.

  18. Turbulence Heating ObserveR: - Satellite Mission Proposal

    Science.gov (United States)

    Vaivads, A.; Retino, A.; Soucek, J.; Khotyaintsev, Yu V.; Valentini, F.; Escoubet, C. P.; Alexandrova, O.; Andre, M.; Bale, S. D.; Balikhin, M.; hide

    2016-01-01

    The Universe is permeated by hot, turbulent, magnetized plasmas. Turbulent plasma is a major constituent of active galactic nuclei, supernova remnants, the intergalactic and interstellar medium, the solar corona, the solar wind and the Earths magnetosphere, just to mention a few examples. Energy dissipation of turbulent fluctuations plays a key role in plasma heating and energization, yet we still do not understand the underlying physical mechanisms involved. THOR is a mission designed to answer the questions of how turbulent plasma is heated and particles accelerated, how the dissipated energy is partitioned and how dissipation operates in different regimes of turbulence. THOR is a single-spacecraft mission with an orbit tuned to maximize data return from regions in near-Earth space magnetosheath, shock, foreshock and pristine solar wind featuring different kinds of turbulence. Here we summarize the THOR proposal submitted on 15 January 2015 to the Call for a Medium-size mission opportunity in ESAs Science Programme for a launch in 2025 (M4). THOR has been selected by European Space Agency (ESA) for the study phase.

  19. Free convection film flows and heat transfer laminar free convection of phase flows and models for heat-transfer analysis

    CERN Document Server

    Shang, De-Yi

    2012-01-01

    This book presents recent developments in our systematic studies of hydrodynamics and heat and mass transfer in laminar free convection, accelerating film boiling and condensation of Newtonian fluids, as well as accelerating film flow of non-Newtonian power-law fluids (FFNF). These new developments provided in this book are (i) novel system of analysis models based on the developed New Similarity Analysis Method; (ii) a system of advanced methods for treatment of gas temperature- dependent physical properties, and liquid temperature- dependent physical properties; (iii) the organically combined models of the governing mathematical models with those on treatment model of variable physical properties; (iv) rigorous approach of overcoming a challenge on accurate solution of three-point boundary value problem related to two-phase film boiling and condensation; and (v) A pseudo-similarity method of dealing with thermal boundary layer of FFNF for greatly simplifies the heat-transfer analysis and numerical calculati...

  20. Convective Heating of the LIFE Engine Target During Injection

    Energy Technology Data Exchange (ETDEWEB)

    Holdener, D S; Tillack, M S; Wang, X R

    2011-10-24

    Target survival in the hostile, high temperature xenon environment of the proposed Laser Inertial Fusion Energy (LIFE) engine is critical. This work focuses on the flow properties and convective heat load imposed upon the surface of the indirect drive target while traveling through the xenon gas. While this rarefied flow is traditionally characterized as being within the continuum regime, it is approaching transition where conventional CFD codes reach their bounds of operation. Thus ANSYS, specifically the Navier-Stokes module CFX, will be used in parallel with direct simulation Monte Carlo code DS2V and analytically and empirically derived expressions for heat transfer to the hohlraum for validation. Comparison of the viscous and thermal boundary layers of ANSYS and DS2V were shown to be nearly identical, with the surface heat flux varying less than 8% on average. From the results herein, external baffles have been shown to reduce this heat transfer to the sensitive laser entrance hole (LEH) windows and optimize target survival independent of other reactor parameters.

  1. Large Eddy Simulations of turbulent flows with heat transfer; Simulation des grandes echelles d'ecoulements turbulents avec transferts de chaleur

    Energy Technology Data Exchange (ETDEWEB)

    Chatelain, A.

    2004-09-15

    LES of turbulent flows with heat transfer was used within the framework of conjugate heat transfer problems. The objective of this work lies not only in identifying the various elements likely to impair temperature fluctuations estimations at the fluid/solid interface but also to introduce adequate wall modeling. The choice of a proper convection scheme for the transport of passive scalars led to the adoption of a high order upwind scheme with slope limiter. The use of classical wall models having shown some weaknesses as for the estimation of parietal temperature fluctuations, two new approaches are proposed and tested. The first one relies on a complete resolution of the Navier-Stokes equations on a refined grid close to the wall making it possible to rebuild the temperature fluctuations near the wall. The second one relies on the simultaneous and one dimensional resolution of a turbulent boundary layer equation and a variance transport equation near the wall. (author)

  2. Application of the Proper Orthogonal Decomposition to Turbulent Czochralski Convective Flows

    Energy Technology Data Exchange (ETDEWEB)

    Rahal, S [Department of Mechanical Engineering, University of Batna, Rue Boukhlouf Mohamed el Hadi, 05000 Batna (Algeria); Cerisier, P [IUSTI - CNRS UMR 6595, Polytech' Marseille, Technopole de Chateau-Gombert, 5 rue Enrico Fermi, 13453, Marseille Cedex 13 (France); Azuma, H [Department of Aerospace Engineering, Osaka Prefecture University, Gakuen-cho 1-1, Sakai, Osaka 599-8531 (Japan)

    2007-04-15

    The aim of this work is to study the general aspects of the convective flow instabilities in a simulated Czochralski system. We considered the influence of the buoyancy and crystal rotation. Velocity fields, obtained by an ultrasonic technique, the corresponding 2D Fourier spectra and a correlation function, have been used. Steady, quasi-periodic and turbulent flows, are successively recognized, as the Reynolds number was increased, for a fixed Rayleigh number. The orthogonal decomposition method was applied and the numbers of modes, involved in the dynamics of turbulent flows, calculated. As far as we know, this method has been used for the first time to study the Czochralski convective flows. This method provides also information on the most important modes and allows simple theoretical models to be established. The large rotation rates of the crystal were found to stabilize the flow, and conversely the temperature gradients destabilize the flow. Indeed, the increase of the rotation effects reduces the number of involved modes and oscillations, and conversely, as expected, the increase of the buoyancy effects induces more modes to be involved in the dynamics. Thus, the flow oscillations can be reduced either by increasing the crystal rotation rate to the adequate value, as shown in this study or by imposing a magnetic field.

  3. Heat and mass transfer of a second grade magnetohydrodynamic fluid over a convectively heated stretching sheet

    Directory of Open Access Journals (Sweden)

    Kalidas Das

    2016-10-01

    Full Text Available The present work is concerned with heat and mass transfer of an electrically conducting second grade MHD fluid past a semi-infinite stretching sheet with convective surface heat flux. The analysis accounts for thermophoresis and thermal radiation. A similarity transformations is used to reduce the governing equations into a dimensionless form. The local similarity equations are derived and solved using Nachtsheim-Swigert shooting iteration technique together with Runge–Kutta sixth order integration scheme. Results for various flow characteristics are presented through graphs and tables delineating the effect of various parameters characterizing the flow. Our analysis explores that the rate of heat transfer enhances with increasing the values of the surface convection parameter. Also the fluid velocity and temperature in the boundary layer region rise significantly for increasing the values of thermal radiation parameter.

  4. Natural convection heat transfer for a staggered array of heated, horizontal cylinders within a rectangular enclosure

    Energy Technology Data Exchange (ETDEWEB)

    Triplett, C.E.

    1996-12-01

    This thesis presents the results of an experimental investigation of natural convection heat transfer in a staggered array of heated cylinders, oriented horizontally within a rectangular enclosure. The main purpose of this research was to extend the knowledge of heat transfer within enclosed bundles of spent nuclear fuel rods sealed within a shipping or storage container. This research extends Canaan`s investigation of an aligned array of heated cylinders that thermally simulated a boiling water reactor (BWR) spent fuel assembly sealed within a shipping or storage cask. The results are presented in terms of piecewise Nusselt-Rayleigh number correlations of the form Nu = C(Ra){sup n}, where C and n are constants. Correlations are presented both for individual rods within the array and for the array as a whole. The correlations are based only on the convective component of the heat transfer. The radiative component was calculated with a finite-element code that used measured surface temperatures, rod array geometry, and measured surface emissivities as inputs. The correlation results are compared to Canaan`s aligned array results and to other studies of natural convection in horizontal tube arrays.

  5. Fast Heat Pulse Propagation by Turbulence Spreading

    DEFF Research Database (Denmark)

    Naulin, Volker; Juul Rasmussen, Jens; Mantica, Paola

    2009-01-01

    The propagation of a cold pulse initiated by edge cooling in JET is compared to propagation of the heat wave originating from a modulation of the heating source roughly at mid radius. It is found that the propagation of the cold pulse is by far faster than what could be predicted on the basis of ...

  6. Convection of wall shear stress events in a turbulent boundary layer

    Science.gov (United States)

    Pabon, Rommel; Mills, David; Ukeiley, Lawrence; Sheplak, Mark

    2017-11-01

    The fluctuating wall shear stress is measured in a zero pressure gradient turbulent boundary layer of Reτ 1700 simultaneously with velocity measurements using either hot-wire anemometry or particle image velocimetry. These experiments elucidate the patterns of large scale structures in a single point measurement of the wall shear stress, as well as their convection velocity at the wall. The wall shear stress sensor is a CS-A05 one-dimensional capacitice floating element from Interdisciplinary Consulting Corp. It has a nominal bandwidth from DC to 5 kHz and a floating element size of 1 mm in the principal sensing direction (streamwise) and 0.2 mm in the cross direction (spanwise), allowing the large scales to be well resolved in the current experimental conditions. In addition, a two sensor array of CS-A05 aligned in the spanwise direction with streamwise separations O (δ) is utilized to capture the convection velocity of specific scales of the shear stress through a bandpass filter and peaks in the correlation. Thus, an average wall normal position for the corresponding convecting event can be inferred at least as high as the equivalent local streamwise velocity. This material is based upon work supported by the National Science Foundation Graduate Research Fellowship under Grant No. DGE-1315138.

  7. Mixed convective heat transfer in an inclined cavity with multiple heated elements on one wall

    Science.gov (United States)

    Oosthuizen, P. H.; de Champlain, A.

    1989-06-01

    A numerical investigation has been conducted into mixed forced and free convective heat transfer through a rectangular cavity having two or three identical rectangular elements on the walls, whose faces are heated to a uniform temperature, in the case where the forced flow enters and leaves through the same wall. The study employs the two-dimensional Navier-Stokes, energy, and continuity equations, under assumptions of steady and laminar flow characteristics. Solution parameters are Reynolds number, Grashof number, fluid Prandtl number, cavity aspect ratio, cavity inclination angle, inlet and outlet duct size, and position and aspect ratio of the heated elements.

  8. Evaluation of PBL Parameterizations in WRF at Sub-Kilometer Resolution: Turbulence Statistics in the Convective Boundary Layer

    Science.gov (United States)

    Hailey Shin, Hyeyum; Dudhia, Jimy

    2015-04-01

    Evaluation of the planetary boundary layer (PBL) parameterization up to the present time has focused on profiles of mean and parameterized vertical flux, since the parameterization has been developed for horizontal resolution that cannot resolve any turbulence in the PBL. Meanwhile, recent increase in computing power has been allowing numerical weather prediction at horizontal resolution finer than 1 km, at which kilometer-scale large eddies in the PBL are partly resolvable. In this study, the performance of five PBL parameterizations in the Weather Research and Forecasting (WRF) model is evaluated at sub-kilometer resolution. The evaluation focuses on resolved high-order turbulence statistics, given that modeling at the high resolution is aimed at improving the simulation of resolved fields. The five parameterizations include four nonlocal PBL schemes - the Yonsei University (YSU), Asymmetric Convective Model 2 (ACM2), Eddy Diffusivity Mass Flux (EDMF), and Total Energy Mass Flux (TEMF) schemes, and one local scheme - Mellor-Yamada-Nakanishi-Niino (MYNN) level 2.5 model. Key findings are as follows. 1) None of the PBL schemes are scale-aware. Instead, each PBL scheme has its own best performing resolution in parameterizing subgrid-scale (SGS) vertical transport and resolving eddies, and the resolution appears to be different between heat and momentum. 2) All the selected PBL schemes reproduce total vertical heat transport well, as resolved transport compensates defects of SGS transport. This interaction between the resolved and SGS transports is not found in momentum transport. 3) The local PBL scheme maintains a weakly stable temperature profile in the upper PBL, which was not accomplished by coarser-resolution simulations. 4) The best schemes in simulating mean, energy spectrum, and vertical-velocity histogram, i.e., the first-, second- and third-order statistics, do not coincide.

  9. Heat transfers in porous media. Conduction, convection, radiant transfer; Transferts de chaleur dans les milieux poreux. Conduction, convection, rayonnement

    Energy Technology Data Exchange (ETDEWEB)

    Bories, S.; Mojtabi, A.; Prat, M.; Quintard, M. [Institut de Mecanique des Fluides de Toulouse, 31 (France)

    2008-10-15

    Multiple physico-chemical and transport phenomena take place in porous media. The study of these phenomena requires the knowledge of fluid storage, transfer and mechanical properties of these media. Like all polyphasic heterogenous systems, these properties depend on the morphology of the matrix and of the phenomena interacting in the different phases. This makes the heat transfers in porous media a particularly huge field of researches. This article makes a synthesis of these researches. Content: 1 - classification and characterization of porous media; 2 - modeling of transfer phenomena; 3 - heat transfer by conduction: concept of equivalent thermal conductivity (ETC), modeling of conduction heat transfer, ETC determination; 4 - heat transfer by convection: modeling of convection heat transfer, natural convection (in confined media, along surfaces or impermeable bodies immersed in a saturated porous medium), forced and mixed convection; 5 - radiant heat transfer: energy status equation, approximate solutions of the radiant transfer equation, use of the approximate solutions: case of fibrous insulating materials; 6 - conclusion. (J.S.)

  10. Heat transfer measurements in swept shock wave/turbulent boundary-layer interactions

    Science.gov (United States)

    Lee, Yeol

    An experimental research program providing basic knowledge and establishing a database on the heat transfer in three-dimensional shock wave/boundary-layer interaction is described. High thermal loading in such interactions constitutes a fundamental problem of critical concern to future supersonic and hypersonic flight vehicles. A turbulent boundary-layer on a flat plate is subjected to interactions with swept planar shock waves generated by a sharp fin. Fin angles from 10 deg to 20 deg at freestream Mach numbers 3.0 and 4.0 produce a variety of interaction strengths from weak to very strong. A foil heater generates a uniform heat flux over the surface of interest and thin-film resistance thermometers mounted on it are used to measure the local surface temperature. The heat convection equation is then used to calculate the local heat transfer coefficients. The present heat transfer technique is applied to measure heat transfer distributions for 5 different interaction cases. The experimental data are compared with numerical Navier-Stokes solutions. The estimation of total uncertainty of the present measurements is about plus or minus 10 percent, which makes them suitable for CFD code validation purposes. The measured peak heat transfer data are correlated with the normal Mach number based on the concept of the quasi-conical nature of such interactions, and the results show good agreement with other experimental data.

  11. Understanding and representing the effect of wind shear on the turbulent transfer in the convective boundary layer

    NARCIS (Netherlands)

    Ronda, R.J.; Vilà-Guerau de Arellano, J.; Pino, D.

    2012-01-01

    Goal of this study is to quantify the effect of wind shear on the turbulent transport in the dry Convective Boundary Layer (CBL). Questions addressed include the effect of wind shear on the depth of the mixed layer, the effect of wind shear on the depth and structure of the capping inversion, and

  12. Natural convection heat transfer analysis of ATR fuel elements

    Energy Technology Data Exchange (ETDEWEB)

    Langerman, M.A.

    1992-05-01

    Natural convection air cooling of the Advanced Test Reactor (ATR) fuel assemblies is analyzed to determine the level of decay heat that can be removed without exceeding the melting temperature of the fuel. The study was conducted to assist in the level 2 PRA analysis of a hypothetical ATR water canal draining accident. The heat transfer process is characterized by a very low Rayleigh number (Ra {approx} 10{sup {minus}5}) and a high temperature ratio. Since neither data nor analytical models were available for Ra < 0.1, an analytical approach is presented based upon the integral boundary layer equations. All assumptions and simplifications are presented and assessed and two models are developed from similar foundations. In one model, the well-known Boussinesq approximations are employed, the results from which are used to assess the modeling philosophy through comparison to existing data and published analytical results. In the other model, the Boussinesq approximations are not used, thus making the model more general and applicable to the ATR analysis.

  13. A review on analytical techniques for natural convection investigation in a heated closed enclosure: Case study

    Directory of Open Access Journals (Sweden)

    Minea Alina Adriana

    2015-01-01

    Full Text Available The aim of this paper is to present a theoretical analysis of a few convection problems. The investigations were started from the geometry of a classic muffle manufactured furnace. During this analytical study, different methodologies have been carefully chosen in order to compare and evaluate the effects of applying different analytical methods of the convection heat transfer processes. In conclusion, even if there are available a lot of analytical methods, natural convection in enclosed enclosures can be studied correctly only with numerical analysis. Also, in this article is presented a case study on natural convection application in a closed heated enclosure.

  14. An inverse natural convection problem of estimating the strength of a heat source

    Energy Technology Data Exchange (ETDEWEB)

    Park, H.M.; Chung, O.Y. [Sogang University, Seoul (D.P.R. of Korea). Dpt. of Chemical Engineering

    1999-12-01

    The inverse problem of determining the time-varying strength of a heat source, which causes natural convection in a two-dimensional cavity, is considered. The Boussinesq equation is used to model the natural convection induced by the heat source. The inverse natural convection problem is posed as a minimization problem of the least-square criterion, which is solved by a conjugate gradient method employing the adjoint equation to determine the descent direction. The present method solves the inverse natural convection problem accurately without any simplification of the governing Boussinesq equation. (author)

  15. Adjoint optimization of natural convection problems: differentially heated cavity

    Science.gov (United States)

    Saglietti, Clio; Schlatter, Philipp; Monokrousos, Antonios; Henningson, Dan S.

    2017-12-01

    Optimization of natural convection-driven flows may provide significant improvements to the performance of cooling devices, but a theoretical investigation of such flows has been rarely done. The present paper illustrates an efficient gradient-based optimization method for analyzing such systems. We consider numerically the natural convection-driven flow in a differentially heated cavity with three Prandtl numbers (Pr=0.15{-}7) at super-critical conditions. All results and implementations were done with the spectral element code Nek5000. The flow is analyzed using linear direct and adjoint computations about a nonlinear base flow, extracting in particular optimal initial conditions using power iteration and the solution of the full adjoint direct eigenproblem. The cost function for both temperature and velocity is based on the kinetic energy and the concept of entransy, which yields a quadratic functional. Results are presented as a function of Prandtl number, time horizons and weights between kinetic energy and entransy. In particular, it is shown that the maximum transient growth is achieved at time horizons on the order of 5 time units for all cases, whereas for larger time horizons the adjoint mode is recovered as optimal initial condition. For smaller time horizons, the influence of the weights leads either to a concentric temperature distribution or to an initial condition pattern that opposes the mean shear and grows according to the Orr mechanism. For specific cases, it could also been shown that the computation of optimal initial conditions leads to a degenerate problem, with a potential loss of symmetry. In these situations, it turns out that any initial condition lying in a specific span of the eigenfunctions will yield exactly the same transient amplification. As a consequence, the power iteration converges very slowly and fails to extract all possible optimal initial conditions. According to the authors' knowledge, this behavior is illustrated here for

  16. Finite-size effects lead to supercritical bifurcations in turbulent rotating Rayleigh-B\\'enard convection

    CERN Document Server

    Weiss, Stephan; Zhong, Jin-Qiang; Clercx, Herman J H; Lohse, Detlef; Ahlers, Guenter; 10.1103/PhysRevLett.105.224501

    2011-01-01

    In turbulent thermal convection in cylindrical samples of aspect ratio \\Gamma = D/L (D is the diameter and L the height) the Nusselt number Nu is enhanced when the sample is rotated about its vertical axis, because of the formation of Ekman vortices that extract additional fluid out of thermal boundary layers at the top and bottom. We show from experiments and direct numerical simulations that the enhancement occurs only above a bifurcation point at a critical inverse Rossby number $1/\\Ro_c$, with $1/\\Ro_c \\propto 1/\\Gamma$. We present a Ginzburg-Landau like model that explains the existence of a bifurcation at finite $1/\\Ro_c$ as a finite-size effect. The model yields the proportionality between $1/\\Ro_c$ and $1/\\Gamma$ and is consistent with several other measured or computed system properties.

  17. The effect of sampling rate on interpretation of the temporal characteristics of radiative and convective heating in wildland flames

    Science.gov (United States)

    David Frankman; Brent W. Webb; Bret W. Butler; Daniel Jimenez; Michael Harrington

    2012-01-01

    Time-resolved radiative and convective heating measurements were collected on a prescribed burn in coniferous fuels at a sampling frequency of 500 Hz. Evaluation of the data in the time and frequency domain indicate that this sampling rate was sufficient to capture the temporal fluctuations of radiative and convective heating. The convective heating signal contained...

  18. Experimental Study of Convective Heating on the Back Face and Payload of a Hypersonic Inflatable Aerodynamic Decelerator (HIAD) Aeroshell

    Science.gov (United States)

    Hollis, Brian R.; Berry, Scott A.; Hollingsworth, Kevin E.; Wright, Sheila A.

    2017-01-01

    A wind tunnel test program has been conducted to define convective heating environments on the back-face of a Hypersonic Inflatable Aerodynamic Decelerator aeroshell. Wind tunnel testing was conducted at Mach 6 and Mach 10 at unit Reynolds numbers from 0.5×10(exp 6)/ft to 3.9×10(exp 6)/ft on a 6.3088 in diameter aeroshell model. Global heating data were obtained through phosphor thermography on the aeroshell back face, as well as on the payload and the aeroshell front face. For all test conditions, laminar flow was produced on the aeroshell front face, while the separated wake shear layer and aeroshell back-face boundary layer were transitional or turbulent. Along the leeward centerline of the aeroshell back face and payload centerbody, heating levels increased with both free stream Reynolds number and angle of attack. The Reynolds number dependency was due to increasing strength of wake turbulence with Reynolds number. The angle-of-attack dependency was due to movement of the wake-vortex reattachment point on the aeroshell back face. The maximum heating levels on the aeroshell back face and payload were approximately 5% to 6%, respectively, of the aeroshell front-face stagnation point. To allow for extrapolation of the ground test data to flight conditions, the back face and payload heating levels were correlated as a function of aeroshell front-face peak momentum thickness Reynolds numbers.

  19. Hazard Avoidance Products for Convectively-Induced Turbulence in Support of High-Altitude Global Hawk Aircraft Missions

    Science.gov (United States)

    Griffin, Sarah M.; Velden, Christopher S.

    2018-01-01

    A combination of satellite-based and ground-based information is used to identify regions of intense convection that may act as a hazard to high-altitude aircraft. Motivated by concerns that Global Hawk pilotless aircraft, flying near 60,000 feet, might encounter significant convectively-induced turbulence during research overflights of tropical cyclones, strict rules were put in place to avoid such hazards. However, these rules put constraints on science missions focused on sampling convection with onboard sensors. To address these concerns, three hazard avoidance tools to aid in real-time mission decision support are used to more precisely identify areas of potential turbulence: Satellite-derived Cloud-top height and tropical overshooting tops, and ground-based global network lightning flashes. These tools are used to compare an ER-2 aircraft overflight of tropical cyclone Emily in 2005, which experienced severe turbulence, to Global Hawk overflights of tropical cyclones Karl and Matthew in 2010 that experienced no turbulence. It is found that the ER-2 overflew the lowest cloud tops and had the largest vertical separation from them compared to the Global Hawk flights. Therefore, cold cloud tops alone cannot predict turbulence. Unlike the overflights of Matthew and Karl, Emily exhibited multiple lightning flashes and a distinct overshooting top coincident with the observed turbulence. Therefore, these tools in tandem can better assist in identifying likely regions/periods of intense active convection. The primary outcome of this study is an altering of the Global Hawk overflight rules to be more flexible based on the analyzed conditions.

  20. The effect of convective heating on evaporative heat loss in anesthetized children.

    Science.gov (United States)

    Cassey, John; Salter, Jo; Colyvas, Kim; Burstal, Richard; Stanger, Rohan

    2014-12-01

    Convective warming is effective in maintaining core temperature under anesthesia. It may increase evaporative water loss (EWL). If significant, further investigation of warming modifications to minimize this impact would be warranted. To quantify EWL in two groups of children (warmed and nonwarmed) having surgical procedures under anesthesia. We performed an observational study of well children having general anesthesia for elective surgical procedures lasting ≥60 min. They were recruited sequentially to each of three age groups: 1-12 months, 13 months-5 years, and 5-12 years--with each age group divided into convectively warmed (43°C) and nonwarmed (21°C) subgroups. Evaporative heat loss (EHL) was calculated from accurate measurement of net EWL during the surgical period. Sixty children were studied. As a percentage of body mass, mean EWLs were 0.29 (warmed) and 0.09 (nonwarmed). Using an ancova model, only procedure duration had a significant impact and explained why the extended procedural time in some convectively warmed children led to higher mean EWLs for that group. For the nonwarmed group, the mean Tcore drop was 1.27°C with a contribution from EWL of 0.6°C over ~70 min. Within the age range 1 month-12 years, EHL is not significantly influenced by convective heating under anesthesia. There is no thermal advantage in exploring technique modifications such as humidifying the warming air. Previous estimates of the contribution of EHL to total heat loss in anesthetized children may require revision. © 2014 John Wiley & Sons Ltd.

  1. Statistical and geometrical properties of thermal plumes in turbulent Rayleigh-B\\'{e}nard convection

    CERN Document Server

    Zhou, Quan

    2010-01-01

    We present a systematic experimental study of geometric and statistical properties of thermal plumes in turbulent Rayleigh-B\\'{e}nard convection using the thermochromic-liquid-crystal (TLC) technique. The experiments were performed in three water-filled cylindrical convection cells with aspect ratios 2, 1, and 0.5 and over the Rayleigh-number range $5\\times10^7 \\leq Ra \\leq 10^{11}$. TLC thermal images of horizontal plane cuts at various depths below the top plate were acquired. Three-dimensional images of thermal plumes were then reconstructed from the two-dimensional slices of the temperature field. The results show that the often-called sheetlike plumes are really one-dimensional structures and may be called rodlike plumes. We find that the number densities for both sheetlike/rodlike and mushroomlike plumes have power-law dependence on $Ra$ with scaling exponents of $\\sim 0.3$, which is close to that between the Nusselt number $Nu$ and $Ra$. This result suggests that it is the plume number that primarily d...

  2. Comparison of Measured and Numerically Simulated Turbulence Statistics in a Convective Boundary Layer Over Complex Terrain

    Energy Technology Data Exchange (ETDEWEB)

    Rai, Raj K.; Berg, Larry K.; Kosović, Branko; Mirocha, Jeffrey D.; Pekour, Mikhail S.; Shaw, William J.

    2016-11-25

    High resolution numerical simulation can provide insight into important physical processes that occur within the planetary boundary layer (PBL). The present work employs large eddy simulation (LES) using the Weather Forecasting and Research (WRF) model, with the LES domain nested within mesoscale simulation, to simulate real conditions in the convective PBL over an area of complex terrain. A multiple nesting approach has been used to downsize the grid spacing from 12.15 km (mesoscale) to 0.03 km (LES). A careful selection of grid spacing in the WRF Meso domain has been conducted to minimize artifacts in the WRF-LES solutions. The WRF-LES results have been evaluated with in situ and remote sensing observations collected during the US Department of Energy-supported Columbia BasinWind Energy Study (CBWES). Comparison of the first- and second-order moments, turbulence spectrum, and probability density function (PDF) of wind speed shows good agreement between the simulations and data. Furthermore, the WRF-LES variables show a great deal of variability in space and time caused by the complex topography in the LES domain. The WRF-LES results show that the flow structures, such as roll vortices and convective cells, vary depending on both the location and time of day. In addition to basic studies related to boundary-layer meteorology, results from these simulations can be used in other applications, such as studying wind energy resources, atmospheric dispersion, fire weather etc.

  3. Validity of sound-proof approaches in rapidly-rotating compressible convection: marginal stability versus turbulence

    Science.gov (United States)

    Verhoeven, Jan; Glatzmaier, Gary A.

    2018-01-01

    The validity of the anelastic approximation has recently been questioned in the regime of rapidly-rotating compressible convection in low Prandtl number fluids (Calkins et al. 2015). Given the broad usage and the high computational efficiency of sound-proof approaches in this astrophysically relevant regime, this paper clarifies the conditions for a safe application. The potential of the alternative pseudo-incompressible approximation is investigated, which in contrast to the anelastic approximation is shown to never break down for predicting the point of marginal stability. Its accuracy, however, decreases close to the parameters corresponding to the failure of the anelastic approach, which is shown to occur when the sound-crossing time of the domain exceeds a rotation time scale, i.e. for rotational Mach numbers greater than one. Concerning the supercritical case, which is naturally characterised by smaller rotational Mach numbers, we find that the anelastic approximation does not show unphysical behaviour. Growth rates computed with the linearised anelastic equations converge toward the corresponding fully compressible values as the Rayleigh number increases. Likewise, our fully nonlinear turbulent simulations, produced with our fully compressible and anelastic models and carried out in a highly supercritical, rotating, compressible, low Prandtl number regime show good agreement. However, this nonlinear test example is for only a moderately low convective Rossby number of 0.14.

  4. Comparison of Measured and Numerically Simulated Turbulence Statistics in a Convective Boundary Layer Over Complex Terrain

    Science.gov (United States)

    Rai, Raj K.; Berg, Larry K.; Kosović, Branko; Mirocha, Jeffrey D.; Pekour, Mikhail S.; Shaw, William J.

    2017-04-01

    The Weather Research and Forecasting (WRF) model can be used to simulate atmospheric processes ranging from quasi-global to tens of m in scale. Here we employ large-eddy simulation (LES) using the WRF model, with the LES-domain nested within a mesoscale WRF model domain with grid spacing decreasing from 12.15 km (mesoscale) to 0.03 km (LES). We simulate real-world conditions in the convective planetary boundary layer over an area of complex terrain. The WRF-LES model results are evaluated against observations collected during the US Department of Energy-supported Columbia Basin Wind Energy Study. Comparison of the first- and second-order moments, turbulence spectrum, and probability density function of wind speed shows good agreement between the simulations and observations. One key result is to demonstrate that a systematic methodology needs to be applied to select the grid spacing and refinement ratio used between domains, to avoid having a grid resolution that falls in the grey zone and to minimize artefacts in the WRF-LES model solutions. Furthermore, the WRF-LES model variables show large variability in space and time caused by the complex topography in the LES domain. Analyses of WRF-LES model results show that the flow structures, such as roll vortices and convective cells, vary depending on both the location and time of day as well as the distance from the inflow boundaries.

  5. Extreme dissipation event due to plume collision in a turbulent convection cell

    CERN Document Server

    Schumacher, Joerg

    2016-01-01

    An extreme dissipation event in the bulk of a closed three-dimensional turbulent convection cell is found to be correlated with a strong reduction of the large-scale circulation flow in the system that happens at the same time as a plume emission event from the bottom plate. The reduction in the large-scale circulation opens the possibility for a nearly frontal collision of down- and upwelling plumes and the generation of a high-amplitude thermal dissipation layer in the bulk. This collision is locally connected to a subsequent high-amplitude energy dissipation event in the form of a strong shear layer. Our analysis illustrates the impact of transitions in the large-scale structures on extreme events at the smallest scales of the turbulence, a direct link that is observed in a flow with boundary layers. We also show that detection of extreme dissipation events which determine the far-tail statistics of the dissipation fields in the bulk requires long-time integrations of the equations of motion over at least ...

  6. Examining In-Cloud Convective Turbulence in Relation to Total Lightning and the 3D Wind Field of Severe Thunderstorms

    Science.gov (United States)

    Al-Momar, S. A.; Deierling, W.; Williams, J. K.; Hoffman, E. G.

    2014-12-01

    Convectively induced turbulence (CIT) is commonly listed as a cause or factor in weather-related commercial aviation accidents. In-cloud CIT is generated in part by shears between convective updrafts and downdrafts. Total lightning is also dependent on a robust updraft and the resulting storm electrification. The relationship between total lightning and turbulence could prove useful in operational aviation settings with the use of future measurements from the geostationary lightning mapper (GLM) onboard the GOES-R satellite. Providing nearly hemispheric coverage of total lightning, the GLM could help identify CIT in otherwise data-sparse locations. For a severe thunderstorm case on 7 June 2012 in northeast Colorado, in-cloud eddy dissipation rate estimates from the NCAR/NEXRAD Turbulence Detection Algorithm were compared with cloud electrification data from the Colorado Lightning Mapping Array and radar products from the Denver, Colorado WSR-88D. These comparisons showed that high concentrations of very high frequency (VHF) source densities emitted by lightning occurred near and downstream of the storm's convective core. Severe turbulence was also shown to occur near this area, extending near the melting level of the storm and spreading upward and outward. Additionally, increases/decreases in VHF sources and turbulence volumes occurred within a few minutes of each other; although, light turbulence was shown to increase near one storm's dissipation. This may be due to increased shear from the now downdraft dominate storm. The 3D wind field from this case, obtained by either a dual-Doppler or a Variational Doppler Radar Assimilation System (VDRAS) analysis, will also be examined to further study the relationships between total lightning and thunderstorm kinematics. If these results prove to be robust, lightning may serve as a strong indicator of the location of moderate or greater turbulence.

  7. Laminar convective heat transfer of non-Newtonian nanofluids with constant wall temperature

    Science.gov (United States)

    Hojjat, M.; Etemad, S. Gh.; Bagheri, R.; Thibault, J.

    2011-02-01

    Nanofluids are obtained by dispersing homogeneously nanoparticles into a base fluid. Nanofluids often exhibit higher heat transfer rate in comparison with the base fluid. In the present study, forced convection heat transfer under laminar flow conditions was investigated experimentally for three types of non-Newtonian nanofluids in a circular tube with constant wall temperature. CMC solution was used as the base fluid and γ-Al2O3, TiO2 and CuO nanoparticles were homogeneously dispersed to create nanodispersions of different concentrations. Nanofluids as well as the base fluid show shear thinning (pseudoplastic) rheological behavior. Results show that the presence of nanoparticles increases the convective heat transfer of the nanodispersions in comparison with the base fluid. The convective heat transfer enhancement is more significant when both the Peclet number and the nanoparticle concentration are increased. The increase in convective heat transfer is higher than the increase caused by the augmentation of the effective thermal conductivity.

  8. A numerical method for natural convection and heat conduction around and in a horizontal circular pipe

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, Satoru; Niiyama, Daisuke [Tohoku Univ., Sendai (Japan). Dept. of Aeronautics and Space Engineering; Byeong Rog Shin [Tohoku Univ., Sendai (Japan). Inst. of Fluid Science

    2004-12-01

    Natural convection around a horizontal circular pipe coupled with heat conduction in the solid structure is numerically investigated using a preconditioning method for solving incompressible and compressible Navier-Stokes equations. In this method, fundamental equations are completely reduced to an equation of heat conduction when the flow field is static (zero velocity). Therefore, not only compressible flows but also very slow flows such as natural convection in a flow field and heat conduction in a static field can be simultaneously calculated using the same computational algorithm. In this study, we first calculated the compressible flow around a NACA0012 airfoil with conduction in the airfoil and then simulated natural convections around a horizontal circular pipe with a different heat conductivity. Finally, we numerically investigated the effect of heat conductivity of the pipe on natural convection. (author)

  9. Solutions manual and computer programs for physical and computational aspects of convective heat transfer

    CERN Document Server

    Cebeci, Tuncer

    1989-01-01

    This book is designed to accompany Physical and Computational Aspects of Convective Heat Transfer by T Cebeci and P Bradshaw and contains solutions to the exercises and computer programs for the numerical methods contained in that book Physical and Computational Aspects of Convective Heat Transfer begins with a thorough discussion of the physical aspects of convective heat transfer and presents in some detail the partial differential equations governing the transport of thermal energy in various types of flows The book is intended for senior undergraduate and graduate students of aeronautical, chemical, civil and mechanical engineering It can also serve as a reference for the practitioner

  10. Role of stochasticity in turbulence and convective intermittent transport at the scrape off layer of Ohmic plasma in QUEST

    Science.gov (United States)

    Banerjee, Santanu; Zushi, H.; Nishino, N.; Hanada, K.; Ishiguro, M.; Tashima, S.; Liu, H. Q.; Mishra, K.; Nakamura, K.; Idei, H.; Hasegawa, M.; Fujisawa, A.; Nagashima, Y.; Matsuoka, K.

    2014-07-01

    Statistical features of fluctuations are investigated using the fast camera imaging technique in the scrape of layer (SOL) of electron cyclotron resonance heated Ohmic plasma. Fluctuations in the SOL towards low field side are dominated by coherent convective structures (blobs). Two dimensional structures of the higher order moments (skewness s and kurtosis k) representing the shape of probability density function (PDF) are studied. s and k are seen to be functions of the magnetic field lines. s and k are consistently higher towards the bottom half of the vessel in the SOL showing the blob trajectory along the field lines from the top towards bottom of the vessel. Parabolic relation ( k = A s 2 + C) is observed between s and k near the plasma boundary, featuring steep density gradient region and at the far SOL. The coefficient A, obtained experimentally, indicates a shift of prominence from pure drift-wave instabilities towards fully developed turbulence. Numerical coefficients characterizing the Pearson system are derived which demonstrates the progressive deviation of the PDF from Gaussian towards gamma from the density gradient region, towards the far SOL. Based on a simple stochastic differential equation, a direct correspondence between the multiplicative noise amplitude, increased intermittency, and hence change in PDF is discussed.

  11. Convection generated by a small heat source in a box with a cooled upper contour at constant temperature

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, L P; Marino, B M [Facultad de Ciencias Exactas, Universidad Nacional del Centro de la Provincia de Buenos Aires, Pinto 399, B 7000 GHG Tandil (Argentina); Tovar, R; Castillo, J A, E-mail: lthomas@exa.unicen.edu.ar [Centro de Investigacion en EnergIa, Universidad Nacional Autonoma de Mexico Priv. Xochicalco s/n, Col. Centro, Temixco, Morelos (Mexico)

    2011-05-01

    The flow generated by a linear heat source inside a thermally insulated box with the upper boundary maintained at constant temperature is analyzed by means of a series of experiments. The attention is focused on the steady state during which the heat provided by the source is absorbed by the upper boundary giving place to a particular convective process in two well defined zones. One of them occupies most part of the box from the lower boundary and is characterized by a turbulent convective flow; the other is the thermal boundary layer developed below the cooled top contour where strong fluctuations are detected. Special interest is found in the analogies with the results obtained employing a configuration similar to that used to research the Rayleigh-Benard convection with lower and upper boundaries at constant temperatures but without internal sources. This study has particular relevance to understanding and predicting the use of the cooled-ceiling systems in buildings as a passive solution to enhance the comfort of its inhabitants during hot days with the consequential energy savings.

  12. Heat transfer in Rockwool modelling and method of measurement. The effect of natural convection on heat transfer in fibrous materials

    Energy Technology Data Exchange (ETDEWEB)

    Dyrboel, Susanne

    1998-05-01

    Fibrous materials are some of the most widely used materials for thermal insulation. In this project the focus of interest has been on fibrous materials for building application. Interest in improving the thermal properties of insulation materials is increasing as legislation is being tightened to reduce the overall energy consumption. A knowledge of the individual heat transfer mechanisms - whereby heat is transferred within a particular material is an essential tool to improve continuously the thermal properties of the material. Heat is transferred in fibrous materials by four different transfer mechanisms: conduction through air, conduction through fibres, thermal radiation and convection. In a particular temperature range the conduction through air can be regarded as a constant, and conduction through fibres is an insignificant part of the total heat transfer. Radiation, however, constitutes 25-40% of the total heat transfer in light fibrous materials. In Denmark and a number of other countries convection in fibrous materials is considered as non-existent when calculating heat transmission as well as when designing building structures. Two heat transfer mechanisms have been the focus of the current project: radiation heat transfer and convection. The radiation analysis serves to develop a model that can be used in further work to gain a wider knowledge of the way in which the morphology of the fibrous material, i.e. fibre diameter distribution, fibre orientation distribution etc., influences the radiation heat transfer under different conditions. The convection investigation serves to examine whether considering convection as non-existent is a fair assumption to use in present and future building structures. The assumption applied in practically is that convection makes a notable difference only in very thick insulation, at external temperatures below -20 deg. C, and at very low densities. For large thickness dimensions the resulting heat transfer through the

  13. Mixed convection flow and heat transfer in a vertical wavy channel ...

    African Journals Online (AJOL)

    user

    Buoyancy effects distort the velocity and temperature profiles relative to the forced convection case. This phenomenon is of ... temperatures and stability of the flow. Convective heat ... vaporization in combustion chambers, the finishing of painted walls and in reducing friction of drag on the hulls of ships and submarines.

  14. Roles of convective heating and boundary-layer moisture asymmetry in slowing down the convectively coupled Kelvin waves

    Science.gov (United States)

    Wang, Lu; Li, Tim

    2017-04-01

    Mechanisms for an in-phase relationship between convection and low-level zonal wind and the slow propagation of the convectively coupled Kelvin wave (CCKW) are investigated by analyzing satellite-based brightness temperature and reanalysis data and by constructing a simple theoretical model. Observational data analysis reveals an eastward shift of the low-level convergence and moisture relative to the CCKW convective center. The composite vertical structures show that the low-level convergence lies in the planetary boundary layer (PBL) (below 800 hPa), and is induced by the pressure trough above the top of PBL through an Ekman-pumping process. A traditional view of a slower eastward propagation speed compared to the dry Kelvin waves is attributed to the reduction of atmospheric static stability in mid-troposphere due to the convective heating effect. The authors' quantitative assessment of the heating effect shows that this effect alone cannot explain the observed CCKW phase speed. We hypothesize that additional slowing process arises from the effect of zonally asymmetric PBL moisture. A simple theoretical model is constructed to understand the relative role of the heating induced effective static stability effect and the PBL moisture effect. The result demonstrates the important role of the both effects. Thus, PBL-free atmosphere interaction is important in explaining the observed structure and propagation of CCKW.

  15. Convection influence on ice formation process on the evaporator heat pump pipes

    Directory of Open Access Journals (Sweden)

    Maksimov Vyacheslav

    2017-01-01

    Full Text Available The purpose of this research is to identify the effect of convection on the ice growth process on the evaporator of heat pump, and how this growth can affect the heat exchange, and the evaporator performance. An experimental analyse is done on the heat pump station which depends on water as heat source. A 2D model is built in Comsol environment depending on Brinkman and heat transfer equations. The experimental and mathematical simulation results confirm that the ice formation has a negative effect on the evaporator heat exchange efficiency, and the convection has high effect on ice growth rate and this effect increases when the pipe is closer to the heat exchanger base. The effect of block size on the convection and ice growth rate must be studied in future.

  16. A Numerical Study of Combined Convective and Radiative Heat Transfer in a Rocket Engine Combustion Chamber

    National Research Council Canada - National Science Library

    Savur, Mehmet

    2002-01-01

    A numerical study was conducted to predict the combined convective and radiative heat transfer rates on the walls of a small aspect ratio cylinder representative of the scaled model of a rocket engine combustion chamber...

  17. Convective Structure and Heat Transfer of Liquid Films Evaporating into a Pure Vapor Environment

    Science.gov (United States)

    Kimball, J. T.; Hermanson, J. C.; Allen, J. S.

    2009-11-01

    The stability, convective structure and heat transfer of upward facing, evaporating, thin liquid films were studied experimentally. Dichloromethane, n-pentane, and methanol films initially 5 mm to 50 μm thick were subjected to constant or impulsive superheat levels. The films resided on a temperature controlled, gold-plated copper plate in a closed, degassed test chamber. The dynamic film thickness was measured at multiple discrete points using ultrasound and instability wavelength and convective structure information was obtained by schlieren imaging. For films below the transition Rayleigh number there is little convective heat transfer present within the film. In films above this transition, the Nusselt number increases with increasing Rayleigh number. The transition in the heat flux occurs over a wide range of Marangoni numbers. Transient experiments reveal an initial rise in heat flux due to evaporation, followed by a decrease and then increase at the onset of convective motion.

  18. Lattice Boltzmann simulation of natural convection heat transfer of SWCNT-nanofluid in an open enclosure

    Directory of Open Access Journals (Sweden)

    Mohammad Jafari

    2015-09-01

    Full Text Available The effects of Single Walled Carbon Nanotube and Copper nanoparticles on natural convection heat transfer in an open cavity are investigated numerically. The problem is studied for different volume fractions of nanoparticles (0–1% and aspect ratio of the cavity (1–4 when Rayleigh number varies from 103 to 105. The volume fraction of added nanoparticles to Water is lower than 1% to make a dilute suspension. Although, results show that adding nanoparticles to the base fluid enhances the heat transfer, make a comparison between SWCNT and Cu-nanoparticles shows that the SWCNT-nanoparticle has better performance to enhance the convection rate. It is found that the aspect ratio of the cavity plays an important role on natural convection. An increase of this parameter leads to heat transfer reduction in the target problem. It is concluded that the Carbon Nanotubes can be applied as a passive way to enhance heat transfer in convection problems.

  19. Cloud Resolving Simulations of Convection during AMIE/DYNAMO: Microphysics and Heat / Moisture Budget

    Science.gov (United States)

    Janiga, M. A.; Li, X.; Hagos, S.; Feng, Z.; Wang, S.; Rowe, A.; Tao, W. K.; Zhang, C.

    2014-12-01

    This study compares simulations of convection during the AMIE/DYNAMO field campaign performed using three doubly-periodic cloud-resolving models (CRMs) and one regional CRM. A variety of microphysics parameterizations are used in these simulations. The target of these simulations is the second MJO event of the campaign, including suppressed periods before and after the passage of the convective envelope. The properties of convection in the CRM simulations are compared to observations of reflectivity and hydrometeor type from the dual-polarimetric SPOL radar. Contrasts in the properties of convection between the various simulations are related to their effect on the heat and moisture budgets.

  20. Conjugated Conduction-Free Convection Heat Transfer in an Annulus Heated at Either Constant Wall Temperature or Constant Heat Flux

    Directory of Open Access Journals (Sweden)

    HAROON IMTIAZ

    2017-04-01

    Full Text Available In this paper, we investigate numerically the effect of thermal boundary conditions on conjugated conduction-free convection heat transfer in an annulus between two concentric cylinders using Fourier Spectral method. The inner wall of the annulus is heated and maintained at either CWT (Constant Wall Temperature or CHF (Constant Heat Flux, while the outer wall is maintained at constant temperature. CHF case is relatively more significant for high pressure industrial applications, but it has not received much attention. This study particularly focuses the latter case (CHF. The main influencing parameters on flow and thermal fields within the annulus are: Rayleigh number Ra; thickness of inner wall Rs; radius ratio Rr and inner wall-fluid thermal conductivity ratio Kr. The study has shown that the increase in Kr increases the heat transfer rate through the annulus for heating at CWT and decreases the inner wall dimensionless temperature for heating at CHF and vice versa. It has also been proved that as the Rs increases at fixed Ra and Rr, the heat transfer rate decreases for heating at CWT and the inner wall dimensionless temperature increases for heating at CHF at Kr 1 depends on Rr. It has been shown that for certain combinations of controlling parameters there will be a value of Rr at which heat transfer rate will be minimum in the annulus in case of heating at CWT, while

  1. Convective heat transfer in axisymmetric enclosures of different configurations under the conditions of their axial rotation and external heating

    Science.gov (United States)

    Vetrov, V. V.; Vorobyev, A. A.

    2017-03-01

    The phenomenon of the intensification of convective heat transfer through air cavities under the conditions of their axial rotation and external heating based on the rise of centrifugal body forces in differently heated air medium has been substantiated theoretically and confirmed experimentally. The criterion dependencies for convection coefficients of axisymmetric cylindrical and conical closed air cavities subjected to external heating and axial rotation have been obtained using the results of the physical and numerical experiments. Both single-layer cylindrical cavities and two-layer ones with perforating internal orifices have been considered.

  2. Calculating mass transfer from vertical wet fabrics using a free convection heat transfer correlation

    Energy Technology Data Exchange (ETDEWEB)

    Tafreshi, H. Vahedi; Ercan, E.; Pourdeyhimi, B. [North Carolina State University, Nonwovens Cooperative Research Center, Raleigh, NC (United States)

    2006-07-15

    In this note, the evaporation rate from a vertical wet fabric sheet is calculated using a free convection heat transfer correlation. Chilton-Colburn analogy is used to derive a mass transfer correlation from a heat transfer correlation proposed by Churchill and Chu for free convection from a vertical isothermal plate. The mass transfer rate obtained from this expression has shown excellent agreement with experimental data. (orig.)

  3. MHD forced convective laminar boundary layer flow from a convectively heated moving vertical plate with radiation and transpiration effect.

    Science.gov (United States)

    Uddin, Md Jashim; Khan, Waqar A; Ismail, A I Md

    2013-01-01

    A two-dimensional steady forced convective flow of a Newtonian fluid past a convectively heated permeable vertically moving plate in the presence of a variable magnetic field and radiation effect has been investigated numerically. The plate moves either in assisting or opposing direction to the free stream. The plate and free stream velocities are considered to be proportional to x(m) whilst the magnetic field and mass transfer velocity are taken to be proportional to x((m-1)/2) where x is the distance along the plate from the leading edge of the plate. Instead of using existing similarity transformations, we use a linear group of transformations to transform the governing equations into similarity equations with relevant boundary conditions. Numerical solutions of the similarity equations are presented to show the effects of the controlling parameters on the dimensionless velocity, temperature and concentration profiles as well as on the friction factor, rate of heat and mass transfer. It is found that the rate of heat transfer elevates with the mass transfer velocity, convective heat transfer, Prandtl number, velocity ratio and the magnetic field parameters. It is also found that the rate of mass transfer enhances with the mass transfer velocity, velocity ratio, power law index and the Schmidt number, whilst it suppresses with the magnetic field parameter. Our results are compared with the results existing in the open literature. The comparisons are satisfactory.

  4. Numerical investigation of natural and mixed convection heat transfer on optimal distribution of discrete heat sources mounted on a substrate

    Science.gov (United States)

    Karvinkoppa, M. V.; Hotta, T. K.

    2017-11-01

    The paper deals with the numerical investigation of natural and mixed convection heat transfer on optimal distribution of five non-identical protruding discrete heat sources (Aluminium) mounted on a substrate (Bakelite) board. The heat sources are subjected to a uniform heat flux of 2000 W/m2. The temperature of heat sources along with the effect of thermal interaction between them is predicted by carrying out numerical simulations using ANSYS Icepak, and the results are validated with the existing experimental findings. The results suggest that mixed convection is a better method for cooling of discrete heat source modules. Also, the temperature of heat sources is a strong function of their shape, size, and positioning on the substrate. Effect of radiation is studied by painting the surface of heat sources by black paint. The results conclude that, under natural convection heat transfer, the temperature of heat sources drops by 6-13% from polished to black painted surface, while mixed convection results in the drop by 3-15%. The numerical predictions are in strong agreement with experimental results.

  5. Investigation of the influence of a step change in surface roughness on turbulent heat transfer

    Science.gov (United States)

    Taylor, Robert P.; Coleman, Hugh W.; Taylor, J. Keith; Hosni, M. H.

    1991-01-01

    The use is studied of smooth heat flux gages on the otherwise very rough SSME fuel pump turbine blades. To gain insights into behavior of such installations, fluid mechanics and heat transfer data were collected and are reported for a turbulent boundary layer over a surface with a step change from a rough surface to a smooth surface. The first 0.9 m length of the flat plate test surface was roughened with 1.27 mm hemispheres in a staggered, uniform array spaced 2 base diameters apart. The remaining 1.5 m length was smooth. The effect of the alignment of the smooth surface with respect to the rough surface was also studied by conducting experiments with the smooth surface aligned with the bases or alternatively with the crests of the roughness elements. Stanton number distributions, skin friction distributions, and boundary layer profiles of temperature and velocity are reported and are compared to previous data for both all rough and all smooth wall cases. The experiments show that the step change from rough to smooth has a dramatic effect on the convective heat transfer. It is concluded that use of smooth heat flux gages on otherwise rough surfaces could cause large errors.

  6. Scale/Analytical Analyses of Freezing and Convective Melting with Internal Heat Generation

    Energy Technology Data Exchange (ETDEWEB)

    Ali S. Siahpush; John Crepeau; Piyush Sabharwall

    2013-07-01

    Using a scale/analytical analysis approach, we model phase change (melting) for pure materials which generate constant internal heat generation for small Stefan numbers (approximately one). The analysis considers conduction in the solid phase and natural convection, driven by internal heat generation, in the liquid regime. The model is applied for a constant surface temperature boundary condition where the melting temperature is greater than the surface temperature in a cylindrical geometry. The analysis also consider constant heat flux (in a cylindrical geometry).We show the time scales in which conduction and convection heat transfer dominate.

  7. Effects of Lewis number on coupled heat and mass transfer in a circular tube subjected to external convective heating

    Science.gov (United States)

    Jiao, Anjun; Zhang, Yuwen; Ma, Hongbin; Critser, John

    2010-01-01

    Heat and mass transfer in a circular tube subject to the boundary condition of the third kind is investigated. The closed form of temperature and concentration distributions, the local Nusselt number based on the total external heat transfer and convective heat transfer inside the tube, as well as the Sherwood number were obtained. The effects of Lewis number and Biot number on heat and mass transfer were investigated. PMID:20862211

  8. Transient natural convection and conduction heat transfers on hot box of a coke drum in Pre-heating stage

    Science.gov (United States)

    Siahaan, A. S.; Ambarita, H.; Kawai, H.; Daimaruya, M.

    2017-01-01

    In an oil refinery unit, coke drum is subjected cyclic thermal stress and mechanical loads due to cyclic heating and cooling loads. Thus, the useful life of a coke drum is much shorter than other equipment. One of the most severe locations due to thermal stress is shell to skirt junction. Here, a hot box is proposed. In this study effectiveness of a hot box will be analyzed numerically. The addition of hot box (triangular cavity) was expected to generate natural convection, which will enhance heat transfer. As for the result show that heat flux conduction and natural convection have the same trend. The peak of conduction heat flux is 122 W/m2 and for natural convection is 12 W/m2. In the heating stage of coke drum cycle it found that the natural convection only provide approximately 10 % of heat transfer compare to conduction heat transfer. In this study it was proved that in the heating stage, the addition of triangular enclosure is less effective to enhance the heat transfer than previously thought.

  9. Magnetohydrodynamics Carreau nanofluid flow over an inclined convective heated stretching cylinder with Joule heating

    Directory of Open Access Journals (Sweden)

    Imad Khan

    Full Text Available Current work highlights the computational aspects of MHD Carreau nanofluid flow over an inclined stretching cylinder with convective boundary conditions and Joule heating. The mathematical modeling of physical problem yields nonlinear set of partial differential equations. A suitable scaling group of variables is employed on modeled equations to convert them into non-dimensional form. The integration scheme Runge-Kutta-Fehlberg on the behalf of shooting technique is utilized to solve attained set of equations. The interesting aspects of physical problem (linear momentum, energy and nanoparticles concentration are elaborated under the different parametric conditions through graphical and tabular manners. Additionally, the quantities (local skin friction coefficient, local Nusselt number and local Sherwood number which are responsible to dig out the physical phenomena in the vicinity of stretched surface are computed and delineated by varying controlling flow parameters. Keywords: MHD, Carreau nanofluid, Inclined stretching cylinder, Joule heating, Shooting technique

  10. Control strategy on the double-diffusive convection in a nanofluid layer with internal heat generation

    Science.gov (United States)

    Mokhtar, N. F. M.; Khalid, I. K.; Siri, Z.; Ibrahim, Z. B.; Gani, S. S. A.

    2017-10-01

    The influences of feedback control and internal heat source on the onset of Rayleigh-Bénard convection in a horizontal nanofluid layer is studied analytically due to Soret and Dufour parameters. The confining boundaries of the nanofluid layer (bottom boundary-top boundary) are assumed to be free-free, rigid-free, and rigid-rigid, with a source of heat from below. Linear stability theory is applied, and the eigenvalue solution is obtained numerically using the Galerkin technique. Focusing on the stationary convection, it is shown that there is a positive thermal resistance in the presence of feedback control on the onset of double-diffusive convection, while there is a positive thermal efficiency in the existence of internal heat generation. The possibilities of suppress or augment of the Rayleigh-Bénard convection in a nanofluid layer are also discussed in detail.

  11. Effects of unsteady free stream velocity and free stream turbulence on stagnation point heat transfer

    Science.gov (United States)

    Gorla, R. S. R.

    1984-01-01

    The combined effects of transient free stream velocity and free stream turbulence on heat transfer at a stagnation point over a cylinder situated in a crossflow are studied. An eddy diffusivity model was formulated and the governing momentum and energy equations are integrated by means of the steepest descent method. The numerical results for the wall shear stress and heat transfer rate are correlated by a turbulence parameter. The wall friction and heat transfer rate increase with increasing free stream turbulence intensity.

  12. Experimental Investigation of Large-Scale Flow Structures in Turbulent Mixed Convection

    Science.gov (United States)

    Koerner, Max; Resagk, Christian; Thess, Andre

    2014-11-01

    We report on experimental investigations of the temporal and spatial behavior of large-scale flow structures (LSC) in turbulent mixed convection. Using a reduced scale model room with a passenger cabin based geometry allows a global view on the LSCs, which are mainly responsible for thermal comfort and air quality within rooms. Moreover, the usage of pressurized working gases like air or sulfur hexafluoride (SF6) enables experimental investigations within broad ranges of the Reynolds number Re and Rayleigh number Ra. Thus, it is also possible to achieve realistic values of the dimensionless numbers allowing direct conclusions to be drawn about the LSCs in rooms similar to passenger cabins. The LSCs are determined by measurements of the 2D velocity field using a 2D2C particle image velocimetry system. In order to characterize three-dimensionally evolved flow structures, the measurement plane can be moved throughout the depth of the model room. We found very complex LSCs ranging from two-dimensional to three-dimensional structures and from one-roll systems over simple two-roll ones to chaotic behavior of the flow. The formation the LSCs has a strong dependency on the relation between Re and Ra and they often show distinct coherent oscillations. The authors gratefully acknowledge the DFG (Grant No. TH497-32-1) for financial support.

  13. Open Channel Natural Convection Heat Transfer on a Vertical Finned Plate

    Energy Technology Data Exchange (ETDEWEB)

    Park, Joo Hyun; Heo, Jeong Hwan; Chung, Bum Jin [Kyung Hee Univ., Yongin (Korea, Republic of)

    2013-10-15

    The natural convection heat transfer of vertical plate fin was investigated experimentally. Heat transfer systems were replaced by mass-transfer systems, based on the analogy concept. The experimental results lie within the predictions of the existing heat transfer correlations of plate-fin for the natural convections. An overlapped thermal boundary layers caused increasing heat transfer, and an overlapped momentum boundary layers caused decreasing heat transfer. As the fin height increases, heat transfer was enhanced due to increased inflow from the open side of the fin spacing. When fin spacing and fin height are large, heat transfer was unaffected by the fin spacing and fin height. Passive cooling by natural convection becomes more and more important for the nuclear systems as the station black out really happened at the Fukushima NPPs. In the RCCS (Reactor Cavity Cooling System) of a VHTR (Very High Temperature Reactor), natural convection cooling through duct system is adopted. In response to the stack failure event, extra cooling capacity adopting the fin array has to be investigated. The finned plate increases the surface area and the heat transfer increases. However, the plate of fin arrays may increase the pressure drop and the heat transfer decreases. Therefore, in order to enhance the passive cooling with fin arrays, the parameters for the fin arrays should be optimized. According to Welling and Wooldridge, a natural convection on vertical plate fin is function of Gr, Pr, L, t, S, and H. The present work investigated the natural convection heat transfer of a vertical finned plate with varying the fin height and the fin spacing. In order achieve high Rayleigh numbers, an electroplating system was employed and the mass transfer rates were measured using a copper sulfate electroplating system based on the analogy concept.

  14. Experimental and numerical analysis of convective heat losses from spherical cavity receiver of solar concentrator

    Directory of Open Access Journals (Sweden)

    Shewale Vinod C.

    2017-01-01

    Full Text Available Spherical cavity receiver of solar concentrator is made up of Cu tubing material having cavity diameter 385 mm to analyze the different heat losses such as conduction, convection and radiation. As the convection loss plays major role in heat loss analysis of cavity receiver, the experimental analysis is carried out to study convective heat loss for the temperature range of 55-75°C at 0°, 15°, 30°, 45°, 60°, and 90° inclination angle of downward facing cavity receiver. The numerical analysis is carried out to study convective heat loss for the low temperature range (55-75°C as well as high temperature range (150-300 °C for no wind condition only. The experimental set-up mainly consists of spherical cavity receiver which is insulated with glass wool insulation to reduce the heat losses from outside surface. The numerical analysis is carried out by using CFD software and the results are compared with the experimental results and found good agreement. The result shows that the convective loss increases with decrease in cavity inclination angle and decreases with decrease in mean cavity receiver temperature. The maximum losses are obtained at 0° inclination angle and the minimum losses are obtained at 90° inclination angle of cavity due to increase in stagnation zone in to the cavity from 0° to 90° inclination. The Nusselt number correlation is developed for the low temperature range 55-75°C based on the experimental data. The analysis is also carried out to study the effect of wind speed and wind direction on convective heat losses. The convective heat losses are studied for two wind speeds (3 m/s and 5 m/s and four wind directions [α is 0° (Side-on wind, 30°, 60°, and 90° (head-on wind]. It is found that the convective heat losses for both wind speed are higher than the losses obtained by no wind test. The highest heat losses are found for wind direction α is 60° with respect to receiver stand and lowest heat losses are found

  15. The effect of rowing headgear on forced convective heat loss and radiant heat gain on a thermal manikin headform.

    Science.gov (United States)

    Bogerd, Cornelis P; Brühwiler, Paul A; Heus, Ronald

    2008-05-01

    Both radiant and forced convective heat flow were measured for a prototype rowing headgear and white and black cotton caps. The measurements were performed on a thermal manikin headform at a wind speed of 4.0 m . s(-1) (s = 0.1) in a climate chamber at 22.0 degrees C (s = 0.05), with and without radiant heat flow from a heat lamp, coming from either directly above (90 degrees ) or from above at an angle of 55 degrees . The effects of hair were studied by repeating selected measurements with a wig. All headgear reduced the radiant heat gain compared with the nude headform: about 80% for the caps and 95% for the prototype rowing headgear (P headgear (9%) (P headgear, showing that forced convective heat loss is the dominant heat transfer parameter under the chosen conditions. The results of the headgear - wig combinations were qualitatively similar, with lower absolute heat transfer.

  16. Natural convection heat transfer from a long heated vertical cylinder to an adjacent air gap of concentric and eccentric conditions

    DEFF Research Database (Denmark)

    Hosseini, R.; Kolaei, Alireza Rezania; Alipour, M.

    2012-01-01

    In this work, the natural convection heat transfer from a long vertical electrically heated cylinder to an adjacent air gap is experimentally studied. The aspect and diameter ratios of the cylinder are 55.56 and 6.33, respectively. The experimental measurements were obtained for a concentric...

  17. Supergranulation and multiscale flows in the solar photosphere. Global observations vs. a theory of anisotropic turbulent convection

    Science.gov (United States)

    Rincon, F.; Roudier, T.; Schekochihin, A. A.; Rieutord, M.

    2017-03-01

    The Sun provides us with the only spatially well-resolved astrophysical example of turbulent thermal convection. While various aspects of solar photospheric turbulence, such as granulation (one-Megameter horizontal scale), are well understood, the questions of the physical origin and dynamical organization of larger-scale flows, such as the 30-Megameters supergranulation and flows deep in the solar convection zone, remain largely open in spite of their importance for solar dynamics and magnetism. Here, we present a new critical global observational characterization of multiscale photospheric flows and subsequently formulate an anisotropic extension of the Bolgiano-Obukhov theory of hydrodynamic stratified turbulence that may explain several of their distinctive dynamical properties. Our combined analysis suggests that photospheric flows in the horizontal range of scales between supergranulation and granulation have a typical vertical correlation scale of 2.5 to 4 Megameters and operate in a strongly anisotropic, self-similar, nonlinear, buoyant dynamical regime. While the theory remains speculative at this stage, it lends itself to quantitative comparisons with future high-resolution acoustic tomography of subsurface layers and advanced numerical models. Such a validation exercise may also lead to new insights into the asymptotic dynamical regimes in which other, unresolved turbulent anisotropic astrophysical fluid systems supporting waves or instabilities operate.

  18. Experimental investigation of turbulent transport of momentum and heat in the atmospheric surface layer

    Science.gov (United States)

    Han, Guowen; Zheng, X. J.; Bo, Tianli

    2017-11-01

    In our study, turbulent transport of momentum and heat is investigated in the neutral and unstable atmospheric surface layer (ASL) over the edge of a desert. Our results reveal that with the increase of wind speed the transport efficiencies for momentum and heat increased, furthermore, transport efficiency of momentum increases faster than that of heat. In addition, the method of quadrant analysis and turbulent events were used to analyze the moment flux and heat flux. Experimental results show that the influence of wind speed on moment flux and heat flux can be quite different, which maybe has a great impact on the turbulent transport of momentum and heat in ASL.

  19. Turbulent convection in a horizontal duct with strong axial magnetic field

    Science.gov (United States)

    Zhang, Xuan; Zikanov, Oleg

    2014-11-01

    Convection in a horizontal duct with one heated wall is studied computationally. The work is motivated by the concept of a blanket for fusion reactors, according to which liquid metal slowly flows in toroidal ducts aligned with the main component of the magnetic field. We first assume that the magnetic field is sufficiently strong for the flow to be purely two-dimensional and analyze chaotic flow regimes at very high Grashof numbers. Furthermore, three-dimensional perturbations are considered and the relation between the length of the duct and the critical Hartmann number, below which the flow becomes three-dimensional, is determined. Financial support was provided by the US NSF (Grant CBET 1232851).

  20. On the effect of laterally varying boundary heat flux on rapidly rotating spherical shell convection

    Science.gov (United States)

    Sahoo, Swarandeep; Sreenivasan, Binod

    2017-08-01

    The onset of convection in a rotating spherical shell subject to laterally varying heat flux at the outer boundary is considered in this paper. The focus is on the geophysically relevant regime of rapid rotation (low Ekman number) where the natural length scale of convection is significantly smaller than the length scale imposed by the boundary heat flux pattern. Contrary to earlier studies at a higher Ekman number, we find a substantial reduction in the onset Rayleigh number Rac with increasing lateral variation. The decrease in Rac is shown to be closely correlated to the equatorial heat flux surplus in the steady, basic state solution. The consistency of such a correlation makes the estimation of Rac possible without solving the full stability problem. The steady baroclinic flow has a strong cyclone-anticyclone asymmetry in the kinetic helicity only for equatorially symmetric lateral variations, with possible implications for dynamo action. Equatorially antisymmetric variations, on the other hand, break the symmetry of the mean flow, in turn negating its helicity. Analysis of the perturbation solution reveals strongly localized clusters through which convection rolls drift in and out at a frequency higher than that for the reference case with homogeneous boundary heat flux. Large lateral variations produce a marked decrease in the azimuthal length scale of columns, which indicates that small-scale motions are essential to the transport of heat in rapidly rotating, localized convection. With an equatorially antisymmetric heat flux pattern, convection in individual clusters goes through an asynchronous wax-wane cycle whose frequency is much lower than the drift rate of the columns. These continual variations in convection intensity may in turn result in fluctuations in the magnetic field intensity, an effect that needs to be considered in dynamo models. Finally, there is a notable analogy between the role of a laterally varying boundary heat flux and the role of a

  1. Impact of tidal heating on the onset of convection in Enceladus' ice shell

    Science.gov (United States)

    Behounkova, Marie; Tobie, Gabriel; Choblet, Gael; Cadek, Ondrej

    2013-04-01

    Observations of Enceladus by the Cassini spacecraft indicated that its south pole is very active, with jets of water vapor and ice emanating from warm tectonic ridges. Convective processes in the ice shell are commonly advocated to explain the enhanced activity at the south pole. The conditions under which convection may occur on Enceladus are, however, still puzzling. According to the estimation of Barr and McKinnon (2007) based on scaling laws, convection may initiate in Enceladus' ice shell only for grain size smaller than 0.3 mm, which is very small compared to the grain size observed on Earth in polar ice sheets for similar temperature and stress conditions (2-4mm). Moreover, Bahounková et al. (2012) showed that such enhanced activity periods associated with thermal convection and internal melting should be brief (~ 1 - 10Myrs) and should be followed by relatively long periods of inactivity (~ 100Myrs), with a probable cessation of thermal convection. In order to constrain the likelihood and periodicity of enhanced activity periods, the conditions under which thermal convection may restart are needed to be investigated. In particular, the goal is to understand how tidal heating, especially during periods of elevated eccentricity, may influence the onset of convection. To answer this question, 3D simulations of thermal convection including a self-consistent computation of tidal dissipation using the code Antigone (Bahounková et al., 2010, 2012) were performed, a composite non-Newtonian rheology (Goldsby and Kohlstedt, 2001) and Maxwell-like rheology mimicking Andrade model were considered. Our simulations show that the onset of convection may occur in Enceladus' ice shell only for ice grain size smaller or equal than 0.5 mm in absence of tidal heating. Tidal dissipation shifts the critical grain size for convection up to values of 1-1.5 mm. The convection is initiated in the polar region due to enhanced tidal dissipation in this area and remains in the

  2. Heat Release Effects on Scaling Laws for Turbulent Shear Flows

    Science.gov (United States)

    Tacina, Kathleen M.; Dahm, Werner J. A.

    1996-11-01

    Experiments have long suggested apparent differences in the fundamental scaling laws for turbulent shear flows between reacting and nonreacting flows. These differences result from the density changes produced by exothermic reaction, and are here shown to be similar to the changes produced by free-stream density differences in nonreacting flows. Motivated by this, we show that the fundamental scaling laws can be generalized to predict the changes due to heat release. The bilinear dependence of temperature T(ζ) on an appropriately defined conserved scalar ζ allows the density changes to be related to an equivalent nonreacting flow, in which one of the free-stream fluid temperatures is set to a value determined by the adiabatic flame temperature and the overall stoichiometry. This scaling principle is applied to turbulent jet diffusion flames, and leads to a generalized scaling variable d^+ for both reacting and nonreacting flows; it effectively extends the momentum diameter d^* of Thring & Newby (1952) and Ricou & Spalding (1961) to reacting flows. The resulting predicted effects of heat release show good agreement with all available data from momentum-dominated jet flames. (Supported by GRI Contract No. 5093-260-2728.)

  3. Carbon-nanotube nanofluid thermophysical properties and heat transfer by natural convection

    Science.gov (United States)

    Li, Y.; Suzuki, S.; Inagaki, T.; Yamauchi, N.

    2014-11-01

    We measured the thermophysical properties of suspensions of carbon nanotubes in water as a type of nanofluid, and experimentally investigated their heat transfer characteristics in a horizontal, closed rectangular vessel. Using a previously constructed system for high- reliability measurement, we quantitatively determined their thermophysical properties and the temperature dependence of these properties. We also investigated the as yet unexplained mechanism of heat transport in carbon-nanotube nanofluids and their flow properties from a thermal perspective. The results indicated that these nanofluids are non-Newtonian fluids, whose high viscosity impedes convection and leads to a low heat transfer coefficient under natural convection, despite their high thermal conductivity.

  4. CONVECTIVE AND RADIATIVE HEAT TRANSFER DURING MELTING WIRE IN THE FLOW OF PLASMA ARC

    Directory of Open Access Journals (Sweden)

    A. V. Yershov

    2014-07-01

    Full Text Available The features of convection and radiant heat exchange of argon plasma cross flow from the surface of the melted butt of steel wire with plasma coating on metal surface are considered. We investigated the uneven distribution of convective heat flow around the perimeter of the heating wire The main part of convective heat flux of plasma centered on its wire is shown,. The density of convective heat flow in the neighborhood of its critical point during the heating of the plasma flow in a wire coating is defined. Calculation of the heat flux density is a 3-d plasma radiation. It is shown that the spherical layer of 2 mm radius of argon plasma is optically transparent in the temperature range (8–20 103 k, since the degree of this layer blackness is considerably less than one. It is determined that the density of heat flow radiation of steel electrode surface is negligible compared with the radiation from the plasma column with the temperature 12·103 К

  5. Flow and Convective Heat Transfer of Cylinder Misaligned from Aerodynamic Axis of Cyclone Flow

    Directory of Open Access Journals (Sweden)

    I. L. Leukhin

    2008-01-01

    Full Text Available The paper provides and analyzes results of experimental investigations on physical specific features of hydrodynamics and convective heat transfer of a cyclone flow with a group of round cylinders located symmetrically relative to its aerodynamic axis, calculative equations for average and local heat transfer factors at characteristic sections of cylinder surface.

  6. Effects of Hall current on convective heat generating fluid in slip flow regime

    Energy Technology Data Exchange (ETDEWEB)

    Singh, S.S.; Ram, P.C. (Kenyatta Univ., Nairobi (KE). Dept. of Mathematics); Stower, G.X. (Jomo Kenyatta Univ. College of Agriculture and Technology, Nairobi (KE). Dept. of Mathematics and Computer Science)

    1992-08-01

    The problem of free convection flow of a viscous heat generating rarefied gas is considered for the case when a strong magnetic field is imposed perpendicularly to the plane of flow. Analytical expressions for the velocity field and temperature are obtained, and the influence of the Hall currents m and the heat source parameter {delta} on the velocity field and temperature are discussed. (Author).

  7. Indirect involvement of armorphous carbon layer on convective heat transfer enhancement using carbon nanofibers

    NARCIS (Netherlands)

    Taha, T.J.; Lefferts, Leonardus; van der Meer, Theodorus H.

    2015-01-01

    In this work, an experimental heat transfer investigation was carried out to investigate the combined influence of both amorphous carbon (a-C) layer thickness and carbon nanofibers (CNFs) on the convective heat transfer behavior. Synthesis of these carbon nanostructures was achieved using catalytic

  8. The effect of blowing or suction on laminar free convective heat transfer on flat horizontal plates

    NARCIS (Netherlands)

    Brouwers, Jos

    1993-01-01

    In the present paper laminar free convective heat transfer on flat permeable horizontal plates is investigated. To assess the effect of surface suction or injection on heat transfer a correction factor, provided by the film model (or ldquofilm theoryrdquo), is applied. Comparing the film model

  9. Enhancement of convective heat transfer coefficient of ethylene glycol base cuprous oxide (Cu2O) nanofluids

    Science.gov (United States)

    Hassan, Ali; Ramzan, Naveed; Umer, Asim; Ahmad, Ayyaz; Muryam, Hina

    2017-08-01

    The enhancement in the convective heat transfer coefficient of the ethylene glycol (EG) base cuprous oxide (Cu2O) nanofluids were investigated. The nanofluids of different volume concentrations i-e 1%, 2.5% and 4.5% were prepared by the two step method. Cuprous oxide (Cu2O) nanoparticles were ultrasonically stirred for four hours in the ethylene glycol (EG). The experimental study has been performed through circular tube geometry in laminar flow regime at average Reynolds numbers 36, 71 and 116. The constant heat flux Q = 4000 (W/m2) was maintained during this work. Substantial enhancement was observed in the convective heat transfer coefficient of ethylene glycol (EG) base cuprous oxide (Cu2O) nanofluids than the base fluid. The maximum 74% enhancement was observed in convective heat transfer coefficient at 4.5 vol% concentration and Re = 116.

  10. A visual description of the convective flow field around the heat of a human

    DEFF Research Database (Denmark)

    Özcan, Oktay; Meyer, Knud Erik; Melikov, Arsen Krikor

    2005-01-01

    Mean velocity data obtained by PIV (Particle Image Velocimetry) around the head of a real-life size breathing thermal manikin are presented for two cases of `no breathing' and `continuous exhalation through nose'. Experiments were conducted in a special chamber which provided stationary convective...... flows around the seated manikin. Results are limited to the plane of symmetry. The paper aims to describe the physical structure of the turbulent flow field by presenting velocity and vorticity data in color graphics....

  11. 3D CFD simulations to study the effect of inclination of condenser tube on natural convection and thermal stratification in a passive decay heat removal system

    Energy Technology Data Exchange (ETDEWEB)

    Minocha, Nitin [Homi Bhabha National Institute, Anushaktinagar, Mumbai 400 094 (India); Joshi, Jyeshtharaj B., E-mail: jbjoshi@gmail.com [Homi Bhabha National Institute, Anushaktinagar, Mumbai 400 094 (India); Department of Chemical Engineering, Institute of Chemical Technology, Matunga, Mumbai 400 019 (India); Nayak, Arun K. [Reactor Engineering Division, Bhabha Atomic Research Center, Trombay, Mumbai 400 085 (India); Vijayan, Pallippattu K., E-mail: vijayanp@barc.gov.in [Reactor Engineering Division, Bhabha Atomic Research Center, Trombay, Mumbai 400 085 (India)

    2016-08-15

    Highlights: • Investigation of three-dimensional natural convection and thermal stratification inside large water pool. • Effect of inclination (α) of condenser tube on fluid flow and heat transfer. • The heat transfer was found to be maximum for α = 90° and minimum for α = 15°. • Laminar-turbulent natural convection and heat transfer in the presence of longitudinal vortices. - Abstract: Many advanced nuclear reactors adopt methodologies of passive safety systems based on natural forces such as gravity. In one of such system, the decay heat generated from a reactor is removed by isolation condenser (ICs) submerged in a large water pool called the Gravity Driven Water Pool (GDWP). The objective of the present study was to design an IC for the passive decay heat removal system (PDHRS) for advanced nuclear reactor. First, the effect of inclination of IC tube on three dimensional temperature and flow fields was investigated inside a pilot scale (10 L) GDWP. Further, the knowledge of these fields has been used for the quantification of heat transfer and thermal stratification phenomenon. In a next step, the knowledge gained from the pilot scale GDWP has been extended to design an IC for real size GDWP (∼10,000 m{sup 3}). Single phase CFD simulation using open source CFD code [OpenFOAM-2.2] was performed for different tube inclination angles (α) (w.r.t. to vertical direction) in the range 0° ⩽ α ⩽ 90°. The results indicate that the heat transfer coefficient increases with increase in tube inclination angle. The heat transfer was found to be maximum for α = 90° and minimum for α = 15°. This behavior is due to the interaction between the primary flow (due to pressure gradient) and secondary flow (due to buoyancy force). The primary flow enhanced the fluid sliding motion at the tube top whereas the secondary flow resulted in enhancement in fluid motion along the circumference of tube. As the angle of inclination (α) of the tube was increased, the

  12. Sensing turbulent flow and heat transport in a cave conduit

    Science.gov (United States)

    Kurtzman, D.; Lucia, F. J.; Jennings, J. W.; Wilson, J. L.; Tyler, S. W.; Jorgensen, A. M.; Dwivedi, R.; Boston, P.; Burger, P.

    2008-12-01

    Cave systems provide an extreme example of complex subsurface porous media, dominated by flow through an interconnected network of conduits. Whether water or air-filled, these flow systems have been largely observed subjectively, with only a few simple quantitative measurements of flow and pressure. In the spring of 2008 a joint campaign of New Mexico Tech and the University of Nevada Reno entered the 210m deep, ~8m "diameter," keyhole shaped, subhorizontal, Left Hand Tunnel, a large air-filled conduit in Carlsbad Caverns, New Mexico, with the intent to observe fluid flow with modern thermally-based instruments. The conduit experiences countercurrent, thermally stratified flow, with mean velocities in each layer less than 0.1m/s. It is part of a geothermally forced, large-scale convection cell. Two instruments were deployed. A distributed temperature sensing (DTS) fiber optic cable was stretched over 1km of the tunnel, and partially suspended by balloons to the roof, to sense spatial and low-frequency (0.01Hz) temporal variations of temperature with a resolution approaching 0.05 degree C. The mean temperature difference between layers was on the order of 0.5 degree and the caveward (subhorizontal) temperature gradient was 1 degree/400m. Influences of connecting subvertical shafts, wet areas of the cave, human activity, and diurnal fluctuations were observed. The second instrument, a 7m tall tower with an array of eight 300Hz thermocouple temperature sensors, with a sensitivity approaching 0.005 degree, was deployed 200m into the tunnel and used to detect high- frequency temperature fluctuations associated with turbulence and the stratified flow. Turbulence structure of each layer was similar. Temperature fluctuation (and turbulence intensity?) was significantly greater near the boundary between layers and its steep vertical gradient of mean temperature. Results from this 3-day campaign, as limited as they are, suggest that there is a wealth of information and

  13. A numerical study of momentum and forced convection heat transfer ...

    African Journals Online (AJOL)

    ASME J. Heat Transfer, Vol. 99, 180-186. [2] Webb B.W., Ramadhyani S., 1985. Conjugate heat transfer in a channel with staggered ribs, Int. J. Heat Mass. Transfer, Vol. 28, 1679-1687. [3] Kelkar K.M.&Patankar S.V., 1987. Numerical prediction of flow and heat transfer in a parallel plate channel with staggered fins, ASME J.

  14. Anomalous heat transport and condensation in convection of cryogenic helium

    Czech Academy of Sciences Publication Activity Database

    Urban, Pavel; Schmoranzer, D.; Hanzelka, Pavel; Sreenivasan, K. R.; Skrbek, L.

    2013-01-01

    Roč. 110, č. 20 (2013), s. 8036-8039 ISSN 0027-8424 R&D Projects: GA ČR GPP203/12/P897 Institutional support: RVO:68081731 Keywords : two-phase convection * temperature inversion * condensation * rain formation Subject RIV: BK - Fluid Dynamics Impact factor: 9.809, year: 2013

  15. Numerical investigation of natural convection heat transfer of nano ...

    African Journals Online (AJOL)

    An enhanced cell-centered finite-volume procedure has been presented for solving the natural convection of the laminar Al O /Water nanofluid flow in a Γ shaped micro-channel in the slip flow region, including the effects of velocity slip and temperature jump at the wall, which are the main characteristics of flow in the slip ...

  16. Variable viscosity effects on mixed convection heat and mass ...

    African Journals Online (AJOL)

    DR OKE

    porous medium, Physics Letters A, Vol. 372, 14, pp 2355-2358. Jayanthi S. and Kumari M., 2007. Effect of variable viscosity on non-Darcy free or mixed convection flow on a vertical surface in a fluid saturated porous medium, Applied Mathematics and Computations, Vol.186, 2, pp 1643-1659. Kafoussius N.G. and Williams ...

  17. Unsteady MHD free convection flow and heat transfer along an ...

    African Journals Online (AJOL)

    Steady free convection flow of an electrically conducting fluid along an infinite vertical porous plate under Arrhenius kinetics are investigated in the presence of strong transverse magnetic field imposed perpendicularly to the plate .A similarity parameter length scale (h) as a function of time and the suction velocity are ...

  18. Investigating Convective Heat Transfer with an Iron and a Hairdryer

    Science.gov (United States)

    Gonzalez, Manuel I.; Lucio, Jesus H.

    2008-01-01

    A simple experimental set-up to study free and forced convection in undergraduate physics laboratories is presented. The flat plate of a domestic iron has been chosen as the hot surface, and a hairdryer is used to generate an air stream around the plate. Several experiments are proposed and typical numerical results are reported. An analysis and…

  19. Parametric Study of Mixed Convective RadiativeHeat Transfer in an Inclined Annulus

    OpenAIRE

    Raed G. Saihood; Manal H. Al-Hafidh

    2008-01-01

    The steady state laminar mixed convection and radiation through inclined rectangular duct with an interior circular tube is investigated numerically for a thermally and hydrodynamicaly fully developed flow. The two heat transfer mechanisms of convection and radiation are treated independently and simultaneously. The governing equations which used are continuity, momentum and energy equations. These equations are normalized and solved using the Vorticity-Stream function and the Body Fitted Coo...

  20. Reappraising the relationships between physics students’ mental models and predictions: An example of heat convection

    OpenAIRE

    Guo-Li Chiou

    2013-01-01

    Although prediction is claimed to be a prime function of mental models, to what extent students can run their mental models to make predictions of physical phenomena remains uncertain. The purpose of this study, therefore, was first to investigate 30 physics students’ mental models of heat convection, and then to examine the relationship between their mental models and predictions of convection-related phenomena. A series of semistructured interviews was conducted to probe the participants’ m...

  1. Convective Flow of a Colloidal Suspension in a Vertical Slot Heated from Side Wall

    Science.gov (United States)

    Cherepanov, I. N.; Smorodin, B. L.

    2017-12-01

    Convective flows and the transport of nanoparticles are numerically investigated in the vertical slot filled with a colloidal suspension and heated from the side. The thermodiffusion and gravitational sedimentation of the nanoparticles are taken into account. Two different regimes of laminar flow are found. The intensity of the first regime is much lower than in molecular liquids (the magnitudes of the convective and diffusion fluxes have the same order). The second regime is more intensive. The transitions between these two regimes are investigated. It is shown that intensive convective flow completely mixes the colloidal suspension to a homogeneous state as a result of the long transient process.

  2. 2ND EF Conference in Turbulent Heat Transfer, Manchester, UK 1998. Volume 1

    Science.gov (United States)

    1998-06-01

    ered analogous to Brownian motion ; that is, a random wandering process. As a result, such (non-local) trans- port cannot be described within "standard...Counter-Rotating Disks P - 83 P. Diamessis, D. Bouris and G. Bergeles Prediction of Grid Turbulence Evolution with a Simple Multifractal Cascade...Kontomaris et al. (9) was used. Each marker moves due to convective and to molecular effects. The convective part of the motion is calculated from the

  3. Magnetohydrodynamics Carreau nanofluid flow over an inclined convective heated stretching cylinder with Joule heating

    Science.gov (United States)

    Khan, Imad; Shafquatullah; Malik, M. Y.; Hussain, Arif; Khan, Mair

    Current work highlights the computational aspects of MHD Carreau nanofluid flow over an inclined stretching cylinder with convective boundary conditions and Joule heating. The mathematical modeling of physical problem yields nonlinear set of partial differential equations. A suitable scaling group of variables is employed on modeled equations to convert them into non-dimensional form. The integration scheme Runge-Kutta-Fehlberg on the behalf of shooting technique is utilized to solve attained set of equations. The interesting aspects of physical problem (linear momentum, energy and nanoparticles concentration) are elaborated under the different parametric conditions through graphical and tabular manners. Additionally, the quantities (local skin friction coefficient, local Nusselt number and local Sherwood number) which are responsible to dig out the physical phenomena in the vicinity of stretched surface are computed and delineated by varying controlling flow parameters.

  4. Heating and Cooling of Coronal Loops with Turbulent Suppression of Parallel Heat Conduction

    Science.gov (United States)

    Bian, Nicolas; Emslie, A. Gordon; Horne, Duncan; Kontar, Eduard P.

    2018-01-01

    Using the “enthalpy-based thermal evolution of loops” (EBTEL) model, we investigate the hydrodynamics of the plasma in a flaring coronal loop in which heat conduction is limited by turbulent scattering of the electrons that transport the thermal heat flux. The EBTEL equations are solved analytically in each of the two (conduction-dominated and radiation-dominated) cooling phases. Comparison of the results with typical observed cooling times in solar flares shows that the turbulent mean free path {λ }T lies in a range corresponding to a regime in which classical (collision-dominated) conduction plays at most a limited role. We also consider the magnitude and duration of the heat input that is necessary to account for the enhanced values of temperature and density at the beginning of the cooling phase and for the observed cooling times. We find through numerical modeling that in order to produce a peak temperature ≃ 1.5× {10}7 K and a 200 s cooling time consistent with observations, the flare-heating profile must extend over a significant period of time; in particular, its lingering role must be taken into consideration in any description of the cooling phase. Comparison with observationally inferred values of post-flare loop temperatures, densities, and cooling times thus leads to useful constraints on both the magnitude and duration of the magnetic energy release in the loop, as well as on the value of the turbulent mean free path {λ }T.

  5. A Physically Based Horizontal Subgrid-scale Turbulent Mixing Parameterization for the Convective Boundary Layer in Mesoscale Models

    Science.gov (United States)

    Zhou, Bowen; Xue, Ming; Zhu, Kefeng

    2017-04-01

    Compared to the representation of vertical turbulent mixing through various PBL schemes, the treatment of horizontal turbulence mixing in the boundary layer within mesoscale models, with O(10) km horizontal grid spacing, has received much less attention. In mesoscale models, subgrid-scale horizontal fluxes most often adopt the gradient-diffusion assumption. The horizontal mixing coefficients are usually set to a constant, or through the 2D Smagorinsky formulation, or in some cases based on the 1.5-order turbulence kinetic energy (TKE) closure. In this work, horizontal turbulent mixing parameterizations using physically based characteristic velocity and length scales are proposed for the convective boundary layer based on analysis of a well-resolved, wide-domain large-eddy simulation (LES). The proposed schemes involve different levels of sophistication. The first two schemes can be used together with first-order PBL schemes, while the third uses TKE to define its characteristic velocity scale and can be used together with TKE-based higher-order PBL schemes. The current horizontal mixing formulations are also assessed a priori through the filtered LES results to illustrate their limitations. The proposed parameterizations are tested a posteriori in idealized simulations of turbulent dispersion of a passive scalar. Comparisons show improved horizontal dispersion by the proposed schemes, and further demonstrate the weakness of the current schemes.

  6. Turbulent heat/mass transfer at oceanic interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Enstad, Lars Inge

    2005-07-01

    The thesis studies heat/mass transfer and uses various simulation techniques. A numerical method has been developed. 4 papers which describes the work, are included. In the first paper we look at such flow configuration where the flow is driven by a constant pressure gradient and the interface is cooled from above. Papers 2 and 3. 2: The effect of stable density stratification on turbulent vortical structures near an atmosphere-ocean interface driven by low wind shear. 3: Low shear turbulence structures beneath a gas-liquid interface under neutral and stable stratified conditions. A well known feature of the upper layer of the ocean is the presence of counter-rotating streamwise vorticity, so called Langmuir circulation. Earlier numerical investigations show that similar vortex structures appear on small scale induced by shear instability only. Short wave solar radiation may create a stable situation which affects the turbulence near the interface. In these papers we investigate such a flow situation by employing a uniform and constant shear stress at the interface together with a similar heat flux into the interface. In both articles we also use a two-point correlation to give a statistical representation of the streamwise vorticity. The spatial extent and intensity are decreased by stable stratification. In addition, in article 3, we find that the Reynolds stress is damped by stable stratification. This leads to an increased mean velocity since decreased Reynolds stress is compensated by a larger mean velocity gradient. The cospectra of the Reynolds stress in the spanwise direction show that the production of Reynolds stress is decreased at lower wave numbers and thus shifted to higher wave numbers in the presence of stable stratification. The streak structure created by the streamwise vorticity is disorganized by stable stratification. Article 4: A numerical study of a density interface using the General Ocean Turbulence Model (GOTM) coupled with a Navier Stokes

  7. The effect of external heat transfer on thermal explosion in a spherical vessel with natural convection.

    Science.gov (United States)

    Campbell, A N

    2015-07-14

    When any exothermic reaction proceeds in an unstirred vessel, natural convection may develop. This flow can significantly alter the heat transfer from the reacting fluid to the environment and hence alter the balance between heat generation and heat loss, which determines whether or not the system will explode. Previous studies of the effects of natural convection on thermal explosion have considered reactors where the temperature of the wall of the reactor is held constant. This implies that there is infinitely fast heat transfer between the wall of the vessel and the surrounding environment. In reality, there will be heat transfer resistances associated with conduction through the wall of the reactor and from the wall to the environment. The existence of these additional heat transfer resistances may alter the rate of heat transfer from the hot region of the reactor to the environment and hence the stability of the reaction. This work presents an initial numerical study of thermal explosion in a spherical reactor under the influence of natural convection and external heat transfer, which neglects the effects of consumption of reactant. Simulations were performed to examine the changing behaviour of the system as the intensity of convection and the importance of external heat transfer were varied. It was shown that the temporal development of the maximum temperature in the reactor was qualitatively similar as the Rayleigh and Biot numbers were varied. Importantly, the maximum temperature in a stable system was shown to vary with Biot number. This has important consequences for the definitions used for thermal explosion in systems with significant reactant consumption. Additionally, regions of parameter space where explosions occurred were identified. It was shown that reducing the Biot number increases the likelihood of explosion and reduces the stabilising effect of natural convection. Finally, the results of the simulations were shown to compare favourably with

  8. Mathematical Simulation of Convective Heat Transfer in the Low-Temperature Storage of Liquefied Natural Gas

    Directory of Open Access Journals (Sweden)

    Shestakov Igor A.

    2015-01-01

    Full Text Available The article shows the results of mathematical modeling of convective heat transfer in the low-temperature storage of liquefied natural gas. Regime of natural convection in an enclosure with different intensity of the heat flux at the external borders are investigated. Was examined two-dimensional nonstationary problem within the model of Navier-Stokes in dimensionless variables “vorticity - stream function - temperature”. Distributions of hydrodynamic parameters and temperatures that characterize the basic regularities of the processes are obtained. Circulating flows are determined and carried out the analysis of vortices formation mechanism and the temperature distribution in solution at conditions of natural convection when the Grashof number (Gr = 106. A significant influence of heat transfer rate on solutions boundary on flow structure and temperature field in LNG storage tanks.

  9. Inverse natural convection problem of estimating wall heat flux using a moving sensor

    Energy Technology Data Exchange (ETDEWEB)

    Park, H.M.; Chung, O.Y.

    1999-11-01

    Inverse heat transfer problems have many applications in various branch of science and engineering. Here, the inverse problem of determining heat flux at the bottom wall of a two-dimensional cavity from temperature measurement in the domain is considered. The Boussinesq equation is used to model the natural convection induced by the wall heat flux. The inverse natural convection problem is posed as a minimization problem of the performance function, which is the sum of square residuals between calculated and observed temperature, by means of a conjugate gradient method. Instead of employing several fixed sensors, a single sensor is used which is moving at a given frequency over the bottom wall. The present method solves the inverse natural convection problem accurately without a priori information about the unknown function to be estimated.

  10. Topical report: Natural convection shutdown heat removal test facility (NSTF) evaluation for generating additional reactor cavity cooling system (RCCS) data.

    Energy Technology Data Exchange (ETDEWEB)

    Farmer, M. T.; Kilsdonk, D. J.; Tzanos, C.P.; Lomperski, S.; Aeschlimann, R.W.; Pointer, D.; Nuclear Engineering Division

    2005-09-01

    As part of the Department of Energy (DOE) Generation IV roadmapping activity, the Very High Temperature gas cooled Reactor (VHTR) has been selected as the principal concept for hydrogen production and other process-heat applications such as district heating and potable water production. On this basis, the DOE has selected the VHTR for additional R&D with the ultimate goal of demonstrating emission-free electricity and hydrogen production with this advanced reactor concept. One of the key passive safety features of the VHTR is the potential for decay heat removal by natural circulation of air in a Reactor Cavity Cooling System (RCCS). The air-cooled RCCS concept is notably similar to the Reactor Vessel Auxiliary Cooling System (RVACS) that was developed for the General Electric PRISM sodium-cooled fast reactor. As part of the DOE R&D program that supported the development of this fast reactor concept, the Natural Convection Shutdown Heat Removal Test Facility (NSTF) was developed at ANL to provide proof-of-concept data for the RVACS under prototypic natural convection flow, temperature, and heat flux conditions. Due to the similarity between RVACS and the RCCS, current VHTR R&D plans call for the utilization of the NSTF to provide RCCS model development and validation data, in addition to supporting design validation and optimization activities. Both air-cooled and water-cooled RCCS designs are to be included. In support of this effort, ANL has been tasked with the development of an engineering plan for mechanical and instrumentation modifications to NSTF to ensure that sufficiently detailed temperature, heat flux, velocity and turbulence profiles are obtained to adequately qualify the codes under the expected range of air-cooled RCCS flow conditions. Next year, similar work will be carried out for the alternative option of a water-cooled RCCS design. Analysis activities carried out in support of this experiment planning task have shown that: (a) in the RCCS, strong

  11. Evaluation of convective heat transfer coefficient of various crops in cyclone type dryer

    Energy Technology Data Exchange (ETDEWEB)

    Akpinar, E. Kavak [Mechanical Engineering Department, Firat University, 23279 Elazig (Turkey)]. E-mail: eakpinar@firat.edu.tr

    2005-09-15

    In this paper, an attempt was made to evaluate the convective heat transfer coefficient during drying of various crops and to investigate the influences of drying air velocity and temperature on the convective heat transfer coefficient. Drying was conducted in a convective cyclone type dryer at drying air temperatures of 60, 70 and 80 deg. C and velocities of 1 and 1.5 m/s using rectangle shaped potato and apple slices (12.5 x 12.5 x 25 mm) and cylindrical shaped pumpkin slices (35 x 5 mm). The temperature changes of the dried crops and the temperature of the drying air were measured during the drying process. It was found that the values of convective heat transfer coefficient varied from crop to crop with a range 30.21406 and 20.65470 W/m{sup 2} C for the crops studied, and it was observed that the convective heat transfer coefficient increased in large amounts with the increase of the drying air velocity but increased in small amounts with the rise of the drying air temperature.

  12. Effect of radiation on convection in a top-heated enclosure

    Energy Technology Data Exchange (ETDEWEB)

    Degroph, H.C. III; Kassemi, M. (NASA Lewis Research Center, Cleveland, OH (United States))

    1993-10-01

    The top-heated enclosure is of considerable importance in many engineering situations, especially in crystal growth from vapor where it is used to minimize convection. In this work we present a combined numerical and experimental investigation of radiation induced convection to show that the convective stability of the top-heated enclosure is disrupted by heat transfer conditions at the wall. When the enclosure is not insulated, the thermal stratification of the fluid is modified by convective and radiative losses to the surrounding environment. This results in a double annular cell flow, which when cut by the laser sheet, shows a four-vortex pattern with a weak annular cell at the bottom and a large counter-rotating annular cell at the top. When the enclosure is insulated, the convective stability of the fluid is again disrupted; this time as a result of radiative heat transfer between the enclosing surfaces which drives two annular flow cells of relatively equal size. Excellent agreement was found between the numerical predictions and the experiment. Comparison between model and experiments show that radiation effects are important even at temperature levels as low as 300 C, and if these effects are not included, numerical predictions can be far removed from reality.

  13. Transient Convection Due to Imposed Heat Flux: Application to Liquid-Acquisition Devices

    Science.gov (United States)

    Duval, Walter M. B.; Chato, David J.; Doherty, Michael P.

    2014-01-01

    A model problem is considered that addresses the effect of heat load from an ambient laboratory environment on the temperature rise of liquid nitrogen inside an enclosure. This model has applications to liquid acquisition devices inside the cryogenic storage tanks used to transport vapor-free propellant to the main engine. We show that heat loads from Q = 0.001 to 10 W, with corresponding Rayleigh numbers from Ra = 109 to 1013, yield a range of unsteady convective states and temperature rise in the liquid. The results show that Q = 1 to 10 W (Ra = 1012 to 1013) yield temperature distributions along the enclosure height that are similar in trend to experimental measurements. Unsteady convection, which shows selfsimilarity in its planforms, is predicted for the range of heat-load conditions. The onset of convection occurs from a free-convection-dominated base flow that becomes unstable against convective instability generated at the bottom of the enclosure while the top of the enclosure is convectively stable. A number of modes are generated with small-scale thermals at the bottom of the enclosure in which the flow selforganizes into two symmetric modes prior to the onset of the propagation of the instability. These symmetric vertical modes transition to asymmetric modes that propagate as a traveling-wave-type motion of convective modes and are representative of the asymptotic convective state of the flow field. Intense vorticity production is created in the core of the flow field due to the fact that there is shear instability between the vertical and horizontal modes. For the higher Rayleigh numbers, 1012 to 1013, there is a transition from a stationary to a nonstationary response time signal of the flow and temperature fields with a mean value that increases with time over various time bands and regions of the enclosure.

  14. A new method for simultaneous measurement of convective and radiative heat flux in car underhood applications

    Science.gov (United States)

    Khaled, M.; Garnier, B.; Harambat, F.; Peerhossaini, H.

    2010-02-01

    A new experimental technique is presented that allows simultaneous measurement of convective and radiative heat flux in the underhood. The goal is to devise an easily implemented and accurate experimental method for application in the vehicle underhood compartment. The new method is based on a technique for heat-flux measurement developed by the authors (Heat flow (flux) sensors for measurement of convection, conduction and radiation heat flow 27036-2, © Rhopoint Components Ltd, Hurst Green, Oxted, RH8 9AX, UK) that uses several thermocouples in the thickness of a thermal resistive layer (foil heat-flux sensor). The method proposed here uses a pair of these thermocouples with different radiative properties. Measurements validating this novel technique are carried out on a flat plate with a prescribed constant temperature in both natural- and forced-convection flow regimes. The test flat plate is instrumented by this new technique, and also with a different technique that is intrusive but very accurate, used as reference here (Bardon J P and Jarny Y 1994 Procédé et dispositif de mesure transitoire de température et flux surfacique Brevet n°94.011996, 22 February). Discrepancies between the measurements by the two techniques are less than 10% for both convective and radiative heat flux. Error identification and sensitivity analysis of the new method are also presented.

  15. Measurement of turbulent kinetic energy spectrum - Part 2: Convection record measurements

    DEFF Research Database (Denmark)

    Velte, Clara Marika; Buchhave, Preben; Hodzic, Azur

    2017-01-01

    A novel exact temporal to spatial mapping for point measurements in turbulence has been applied to various flow conditions existing in a round turbulent jet. The conditions range between equilibrium and non-equilibrium as well as mid to high turbulence intensities. The exact mapping applies to al...

  16. Heat Transfer Analysis of Passive Residual Heat Removal Heat Exchanger under Natural Convection Condition in Tank

    Directory of Open Access Journals (Sweden)

    Qiming Men

    2014-01-01

    Full Text Available Aiming at the heat transfer calculation of the Passive Residual Heat Removal Heat Exchanger (PRHR HX, experiments on the heat transfer of C-shaped tube immerged in a water tank were performed. Comparisons of different correlation in literatures with the experimental data were carried out. It can be concluded that the Dittus-Boelter correlation provides a best-estimate fit with the experimental results. The average error is about 0.35%. For the tube outside, the McAdams correlations for both horizontal and vertical regions are best-estimated. The average errors are about 0.55% for horizontal region and about 3.28% for vertical region. The tank mixing characteristics were also investigated in present work. It can be concluded that the tank fluid rose gradually which leads to a thermal stratification phenomenon.

  17. EXPERIMENTAL INVESTIGATION OF CONVECTIVE HEAT TRANSFER IN A NARROW RECTANGULAR CHANNEL FOR UPWARD AND DOWNWARD FLOWS

    Directory of Open Access Journals (Sweden)

    DAESEONG JO

    2014-04-01

    Full Text Available Heat transfer characteristics in a narrow rectangular channel are experimentally investigated for upward and downward flows. The experimental data obtained are compared with existing data and predictions by many correlations. Based on the observations, there are differences from others: (1 there are no different heat transfer characteristics between upward and downward flows, (2 most of the existing correlations under-estimate heat transfer characteristics, and (3 existing correlations do not predict the high heat transfer in the entrance region for a wide range of Re. In addition, there are a few heat transfer correlations applicable to narrow rectangular channels. Therefore, a new set of correlations is proposed with and without consideration of the entrance region. Without consideration of the entrance region, heat transfer characteristics are expressed as a function of Re and Pr for turbulent flows, and as a function of Gz for laminar flows. The correlation proposed for turbulent and laminar flows has errors of ±18.25 and ±13.62%, respectively. With consideration of the entrance region, the heat transfer characteristics are expressed as a function of Re, Pr, and z* for both laminar and turbulent flows. The correlation for turbulent and laminar flows has errors of ±19.5 and ±22.0%, respectively.

  18. Large scale three-dimensional topology optimisation of heat sinks cooled by natural convection

    DEFF Research Database (Denmark)

    Alexandersen, Joe; Sigmund, Ole; Aage, Niels

    2016-01-01

    This work presents the application of density-based topology optimisation to the design of three-dimensional heat sinks cooled by natural convection. The governing equations are the steady-state incompressible Navier-Stokes equations coupled to the thermal convection-diffusion equation through...... topologies verify prior conclusions regarding fin length/thickness ratios and Biot numbers, but also indicate that carefully tailored and complex geometries may improve cooling behaviour considerably compared to simple heat fin geometries. (C) 2016 Elsevier Ltd. All rights reserved....

  19. Determining convective heat transfer coefficient using phoenics software package

    Energy Technology Data Exchange (ETDEWEB)

    Kostikov, A.; Matsevity, Y. [Institute of Mechanical Engineering Problems of National Academy of Sciences of Ukraine, Kharkov (Ukraine)

    1997-12-31

    The two methods of determination of such important quantity of heat exchange on a body surface using PHOENICS are suggested in the presentation. The first method consists in a post-processing of results of conjugate heat transfer problem solved by PHOENICS. The second one is solving an inverse heat conduction problem for solid body using PHOENICS. Comparative characteristic of these two methods is represented. (author) 4 refs.

  20. Bounds on heat transport in Bénard-Marangoni convection

    Science.gov (United States)

    Hagstrom, George; Doering, Charles R.

    2010-04-01

    For Pearson’s model of Bénard-Marangoni convection, the Nusselt number Nu is proven to be bounded as a function Marangoni number Ma according to Nu≤0.838×Ma2/7 for infinite Prandtl number and according to Nu≲Ma1/2 uniformly for finite Prandtl number. The analysis is also used to raise the lower bound for the critical Marangoni number for energy stability of the conduction solution from 56.77 to 58.36 when the Prandtl number is infinite.

  1. Research of the convective heat exchange of relatively long cyclone chamber with use gradient heat flux sensors

    Science.gov (United States)

    Onokhin, D. A.; Saburov, E. N.; Orekhov, A. N.

    2017-11-01

    The aim of study is research of features of convective heat transfer in relatively long cyclone chamber. The research of heat exchange was carried out in a wide range of Reynolds numbers using gradient heat flow sensors. In the experiments, the value of the entrance area was changed by the flow and the diameter of the outlet. The results obtained were presented in the form of similarity equation. It was proposed to use the possibilities of gradient thermometry for studying the processes of heat exchange in cyclone chambers.

  2. Determination of drying kinetics and convective heat transfer coefficients of ginger slices

    Science.gov (United States)

    Akpinar, Ebru Kavak; Toraman, Seda

    2016-10-01

    In the present work, the effects of some parametric values on convective heat transfer coefficients and the thin layer drying process of ginger slices were investigated. Drying was done in the laboratory by using cyclone type convective dryer. The drying air temperature was varied as 40, 50, 60 and 70 °C and the air velocity is 0.8, 1.5 and 3 m/s. All drying experiments had only falling rate period. The drying data were fitted to the twelve mathematical models and performance of these models was investigated by comparing the determination of coefficient ( R 2), reduced Chi-square ( χ 2) and root mean square error between the observed and predicted moisture ratios. The effective moisture diffusivity and activation energy were calculated using an infinite series solution of Fick's diffusion equation. The average effective moisture diffusivity values and activation energy values varied from 2.807 × 10-10 to 6.977 × 10-10 m2/s and 19.313-22.722 kJ/mol over the drying air temperature and velocity range, respectively. Experimental data was used to evaluate the values of constants in Nusselt number expression by using linear regression analysis and consequently, convective heat transfer coefficients were determined in forced convection mode. Convective heat transfer coefficient of ginger slices showed changes in ranges 0.33-2.11 W/m2 °C.

  3. Numerical modelling of Rayleigh-Benard convection and heat transfer in normal {sup 3}He near the critical point

    Energy Technology Data Exchange (ETDEWEB)

    Polezhaev, V I; Gorbunov, A A; Nikitin, S A; Soboleva, E B [Institute for Problems in Mechanics, Russian Academy of Sciences, Moscow (Russian Federation)], E-mail: polezh@ipmnet.ru

    2009-02-01

    New numerical results on thermal gravity-driven convection in a layer filled with near-critical {sup 3}He and heated from below are presented. Corrections of conditions for convection onset are discussed. The heat transfer calibrations near the critical point are tested using experimental data. Stratification effects are analysed. As found, space environment that suppresses the strong density gradients near the critical point may provoke the enhancement of convection compared to the terrestrial conditions.

  4. Teleconnections, Midlatitude Cyclones and Aegean Sea Turbulent Heat Flux Variability on Daily Through Decadal Time Scales

    Science.gov (United States)

    Romanski, Joy; Romanou, Anastasia; Bauer, Michael; Tselioudis, George

    2013-01-01

    We analyze daily wintertime cyclone variability in the central and eastern Mediterranean during 1958-2001, and identify four distinct cyclone states, corresponding to the presence or absence of cyclones in each basin. Each cyclone state is associated with wind flows that induce characteristic patterns of cooling via turbulent (sensible and latent) heat fluxes in the eastern Mediterranean basin and Aegean Sea. The relative frequency of occurrence of each state determines the heat loss from the Aegean Sea during that winter, with largest heat losses occurring when there is a storm in the eastern but not central Mediterranean (eNOTc), and the smallest occurring when there is a storm in the central but not eastern Mediterranean (cNOTe). Time series of daily cyclone states for each winter allow us to infer Aegean Sea cooling for winters prior to 1985, the earliest year for which we have daily heat flux observations. We show that cyclone states conducive to Aegean Sea convection occurred in 1991/1992 and 1992/1993, the winters during which deep water formation was observed in the Aegean Sea, and also during the mid-1970s and the winters of 1963/1964 and 1968/1969. We find that the eNOTc cyclone state is anticorrelated with the North Atlantic Oscillation (NAO) prior to 1977/1978. After 1977/1978, the cNOTe state is anticorrelated with both the NAO and the North Caspian Pattern (NCP), showing that the area of influence of large scale atmospheric teleconnections on regional cyclone activity shifted from the eastern to the central Mediterranean during the late 1970s. A trend toward more frequent occurrence of the positive phase of the NAO produced less frequent cNOTe states since the late 1970s, increasing the number of days with strong cooling of the Aegean Sea surface waters.

  5. Analytical prediction of forced convective heat transfer of fluids ...

    Indian Academy of Sciences (India)

    Several phenomenological models have been proposed to explain the anomalous heat transfer enhancement in nanofluids. This paper presents a systematic literature survey to exploit the characteristics of nanofluids, viz., thermal conductivity, specific heat and other thermal properties. An empirical correlation for the ...

  6. Scaled model studies of decay heat removal by natural convection for sodium cooled reactors

    Energy Technology Data Exchange (ETDEWEB)

    Hoffmann, H. (Institut fuer Angewandte Thermo- und Fluiddynamik (IATF), Kernforschungszentrum Karlsruhe (Germany)); Weinberg, D. (Institut fuer Angewandte Thermo- und Fluiddynamik (IATF), Kernforschungszentrum Karlsruhe (Germany)); Marten, K. (Institut fuer Angewandte Thermo- und Fluiddynamik (IATF), Kernforschungszentrum Karlsruhe (Germany)); Schnetgoeke, G. (Institut fuer Angewandte Thermo- und Fluiddynamik (IATF), Kernforschungszentrum Karlsruhe (Germany))

    1993-06-01

    Thermohydraulic experiments were performed with water in order to simulate decay heat removal by natural convection in a pool-type sodium cooled reactor. Two water test rigs of different scales were used, namely, RAMONA (1:20) and NEPTUN (1:5). RAMONA was taken to study the transition from nominal operation by forced convection to decay heat removal operation by natural convection. Steady-state similarity tests were carried out in both facilities. All tests provide a basis for verification of computer programs. Calculations performed with the three-dimensional code FLUTAN proved that the thermohydraulic processes are quantitatively mastered, even for the very complex geometry of the NEPTUN test rig. (orig.)

  7. Methods for characterizing convective cryoprobe heat transfer in ultrasound gel phantoms.

    Science.gov (United States)

    Etheridge, Michael L; Choi, Jeunghwan; Ramadhyani, Satish; Bischof, John C

    2013-02-01

    While cryosurgery has proven capable in treating of a variety of conditions, it has met with some resistance among physicians, in part due to shortcomings in the ability to predict treatment outcomes. Here we attempt to address several key issues related to predictive modeling by demonstrating methods for accurately characterizing heat transfer from cryoprobes, report temperature dependent thermal properties for ultrasound gel (a convenient tissue phantom) down to cryogenic temperatures, and demonstrate the ability of convective exchange heat transfer boundary conditions to accurately describe freezing in the case of single and multiple interacting cryoprobe(s). Temperature dependent changes in the specific heat and thermal conductivity for ultrasound gel are reported down to -150 °C for the first time here and these data were used to accurately describe freezing in ultrasound gel in subsequent modeling. Freezing around a single and two interacting cryoprobe(s) was characterized in the ultrasound gel phantom by mapping the temperature in and around the "iceball" with carefully placed thermocouple arrays. These experimental data were fit with finite-element modeling in COMSOL Multiphysics, which was used to investigate the sensitivity and effectiveness of convective boundary conditions in describing heat transfer from the cryoprobes. Heat transfer at the probe tip was described in terms of a convective coefficient and the cryogen temperature. While model accuracy depended strongly on spatial (i.e., along the exchange surface) variation in the convective coefficient, it was much less sensitive to spatial and transient variations in the cryogen temperature parameter. The optimized fit, convective exchange conditions for the single-probe case also provided close agreement with the experimental data for the case of two interacting cryoprobes, suggesting that this basic characterization and modeling approach can be extended to accurately describe more complicated

  8. MHD natural convection in open inclined square cavity with a heated circular cylinder

    Science.gov (United States)

    Hosain, Sheikh Anwar; Alim, M. A.; Saha, Satrajit Kumar

    2017-06-01

    MHD natural convection in open cavity becomes very important in many scientific and engineering problems, because of it's application in the design of electronic devices, solar thermal receivers, uncovered flat plate solar collectors having rows of vertical strips, geothermal reservoirs, etc. Several experiments and numerical investigations have been presented for describing the phenomenon of natural convection in open cavity for two decades. MHD natural convection and fluid flow in a two-dimensional open inclined square cavity with a heated circular cylinder was considered. The opposite wall to the opening side of the cavity was first kept to constant heat flux q, at the same time the surrounding fluid interacting with the aperture was maintained to an ambient temperature T∞. The top and bottom wall was kept to low and high temperature respectively. The fluid with different Prandtl numbers. The properties of the fluid are assumed to be constant. As a result a buoyancy force is created inside the cavity due to temperature difference and natural convection is formed inside the cavity. The Computational Fluid Dynamics (CFD) code are used to discretize the solution domain and represent the numerical result to graphical form.. Triangular meshes are used to obtain the solution of the problem. The streamlines and isotherms are produced, heat transfer parameter Nu are obtained. The results are presented in graphical as well as tabular form. The results show that heat flux decreases for increasing inclination of the cavity and the heat flux is a increasing function of Prandtl number Pr and decreasing function of Hartmann number Ha. It is observed that fluid moves counterclockwise around the cylinder in the cavity. Various recirculations are formed around the cylinder. The almost all isotherm lines are concentrated at the right lower corner of the cavity. The object of this work is to develop a Mathematical model regarding the effect of MHD natural convection flow around

  9. Measurement of turbulent kinetic energy spectrum - Part 1: Convection record method

    DEFF Research Database (Denmark)

    Buchhave, Preben; Velte, Clara Marika

    2017-01-01

    the relation Δ sn =unΔtn.n indicates the sample number in a measurement sequence. Summation of the consecutive streakline elements, Δ s, corresponding to the convection distance of the fluid, results in a spatial “convection record”. The exact mapping applies to all flows,since it is based on the instantaneous...

  10. Chaotic Convection in a Viscoelastic Fluid Saturated Porous Medium with a Heat Source

    Directory of Open Access Journals (Sweden)

    B. S. Bhadauria

    2016-01-01

    Full Text Available Chaotic convection in a viscoelastic fluid saturated porous layer, heated from below, is studied by using Oldroyd’s type constituting relation and in the presence of an internal heat source. A modified Darcy law is used in the momentum equation, and a heat source term has been considered in energy equation. An autonomous system of fourth-order differential equations has been deduced by using a truncated Fourier series. Effect of internal heat generation on chaotic convection has been investigated. The asymptotic behavior can be stationary, periodic, or chaotic, depending upon the flow parameters. Construction of four-scroll, or “two-butterfly,” and chaotic attractor has been examined.

  11. The Impact of Reduced Gravity on Free Convective Heat Transfer from a Finite, Flat, Vertical Plate

    Science.gov (United States)

    Lotto, Michael A.; Johnson, Kirstyn M.; Nie, Christopher W.; Klaus, David M.

    2017-09-01

    Convective heat transfer is governed by a number of factors including various fluid properties, the presence of a thermal gradient, geometric configuration, flow condition, and gravity. Empirically-derived analytical relationships can be used to estimate convection as a function of these governing parameters. Although it is relatively straightforward to experimentally quantify the contributions of the majority of these variables, it is logistically difficult to assess the influence of reduced-gravity due to practical limitations of establishing this environment. Therefore, in order to explore this regime, a series of tests was conducted to evaluate convection under reduced-gravity conditions averaging 0.45 m/sec2 (0.05 g) achieved aboard a parabolic aircraft. The results showed a reduction in net heat transfer of approximately 61% in flight relative to a 1g terrestrial baseline using the same setup. The average experimental Nusselt Number of 19.05 ± 1.41 statistically correlated with the predicted value of 18.90 ± 0.63 (N = 13), estimated using the Churchill-Chu correlation for free convective heat transfer from a finite, flat, vertical plate. Extrapolating this to similar performance in true microgravity (10-6 g) indicates that these conditions should yield a Nusselt Number of 1.27, which is 2.6% the magnitude of free convection at 1g, or a reduction of 97.4%. With advection essentially eliminated, heat transfer becomes limited to diffusion and radiation, which are gravity-independent and nearly equivalent in magnitude in this case. These results offer a general guideline for integrating components that utilize natural (free) convective gas cooling in a spacecraft habitat and properly sizing the thermal control system.

  12. Tropical Diabatic Heating and the Role of Convective Processes as Represented in Several Contemporary Climate Models

    Science.gov (United States)

    Robertson, Franklin R.; Roads, John; Oglesby, Robert; Marshall, Susan

    2004-01-01

    One of the most fundamental properties of the global heat balance is the net heat input into the tropical atmosphere that helps drive the planetary atmospheric circulation. Although broadly understood in terms of its gross structure and balance of source / sink terms, incorporation of the relevant processes in predictive models is still rather poor. The work reported here examines the tropical radiative and water cycle behavior as produced by four contemporary climate models. Among these are the NSIPP-2 (NASA Seasonal to Interannual Prediction Project) which uses the RAS convective parameterization; the FVCCM, a code using finite volume numerics and the CCM3.6 physics; FVCCM-MCRAS again having the finite volume numerics, but MCRAS convective parameterization and a different radiation treatment; and, finally, the NCEP GSM which uses the RAS. Using multi-decadal integrations with specified SSTs we examine the statistics of radiative / convective processes and associated energy transports, and then estimate model energy flux sensitivities to SST changes. In particular the behavior of the convective parameterizations is investigated. Additional model integrations are performed specifically to assess the importance representing convective inhibition in regulating convective cloud-top structure and moisture detrainment as well as controlling surface energy fluxes. To evaluate the results of these experiments, a number of satellite retrievals are used: TRMM retrievals of vertical reflectivity structure, rainfall rate, and inferred diabatic heating are analyzed to show both seasonal and interannual variations in vertical structure of latent heat release. Top-of-atmosphere radiative fluxes from ERBS and CERES are used to examine shortwave and longwave cloud forcing and to deduce required seasonal energy transports. Retrievals of cloud properties from ISCCP and water vapor variations from SSM/T-2 are also used to understand behavior of the humidity fields. These observations

  13. The Impact of Reduced Gravity on Free Convective Heat Transfer from a Finite, Flat, Vertical Plate

    Science.gov (United States)

    Lotto, Michael A.; Johnson, Kirstyn M.; Nie, Christopher W.; Klaus, David M.

    2017-10-01

    Convective heat transfer is governed by a number of factors including various fluid properties, the presence of a thermal gradient, geometric configuration, flow condition, and gravity. Empirically-derived analytical relationships can be used to estimate convection as a function of these governing parameters. Although it is relatively straightforward to experimentally quantify the contributions of the majority of these variables, it is logistically difficult to assess the influence of reduced-gravity due to practical limitations of establishing this environment. Therefore, in order to explore this regime, a series of tests was conducted to evaluate convection under reduced-gravity conditions averaging 0.45 m/sec2 (0.05 g) achieved aboard a parabolic aircraft. The results showed a reduction in net heat transfer of approximately 61% in flight relative to a 1 g terrestrial baseline using the same setup. The average experimental Nusselt Number of 19.05 ± 1.41 statistically correlated with the predicted value of 18.90 ± 0.63 (N = 13), estimated using the Churchill-Chu correlation for free convective heat transfer from a finite, flat, vertical plate. Extrapolating this to similar performance in true microgravity (10-6 g) indicates that these conditions should yield a Nusselt Number of 1.27, which is 2.6% the magnitude of free convection at 1 g, or a reduction of 97.4%. With advection essentially eliminated, heat transfer becomes limited to diffusion and radiation, which are gravity-independent and nearly equivalent in magnitude in this case. These results offer a general guideline for integrating components that utilize natural (free) convective gas cooling in a spacecraft habitat and properly sizing the thermal control system.

  14. Average Natural Convective Heat Transfer of Air-cooled Condensing Heat Exchanger of Emergency Cooldown Tank - Effect of Tube Banks

    Energy Technology Data Exchange (ETDEWEB)

    Huh, Seon Jeong; Lee, Hee Joon [Kookmin University, Seoul (Korea, Republic of); Kim, Myoung Jun; Moon, Joo Hyung; Bae, Youngmin; Kim, Young-In [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    Recently emergency cooldown tank(ECT) is a great concern of passive cooling system for the safety of nuclear reactor. After the operation of a conventional passive cooling system for an extended period, however, the water level falls as a result of the evaporation from the ECT, as steam is emitted from the open top of the tank. In this study, the effect of heat transfer area at the air cooled condensing heat exchanger was investigated by changing 5×5 tube banks into 4×4 and 3×3. Moreover, each of air-side natural convective heat transfer coefficient of tube banks was compared to existing correlations. This study presents the effect of heat transfer area at air-cooled condensing heat exchanger. As heat transfer area decreased, the temperature of outlet increased. In other words, the cooling performance got lower with the decrease of heat transfer area. In addition, the average natural convective heat transfer coefficient was 15.3 W/m{sup 2}/K from the 4×4 tube banks, and 4.92 W/m{sup 2}/K from the 3×3 tube banks, which had quite a large error more than 46% especially with the value of 4×4 tube banks compared to the value from correlation equation. Therefore, according to this result, it is needed to measure the local heat transfer coefficient of vertical cylinder more elaborately in further study.

  15. Thermomechanically-induced convective motion and natural convection in confined gaseous helium subjected to boundary heating

    Science.gov (United States)

    Sutrisno

    A theoretical analysis of the effects of a gravity field on gaseous helium confined in a slender two dimensional box when boundary heating suddenly takes place at the wall is described. The gravity field is applied vertically. A heat flux, capable of producing an appreciable wall temperature increase, is applied uniformly along the longer vertical walls. A systematic analysis using various perturbation techniques is carried out in the central region away from the upper and lower insulated boundaries. A complete system of conservation equations governing viscous, heat conducting and compressible flow is employed. Analysis on the acoustic timescale shows that conduction heating takes place only in a thin, continuously growing boundary layer near the heated wall. On the conduction timescale, both acoustic and conduction phenomena occur simultaneously in the container. Multiple timescale methods are employed to separate the high frequency acoustic equations from the lower frequency conduction equations. In this fully conductive system, energy is transferred by conduction among the fluid particles which at the same time experience thermal expansion and compression.

  16. Experimental study of transient forced convection heat transfer from simulated electronic chips

    Science.gov (United States)

    Bhowmik, H.; Tou, K. W.

    2005-05-01

    Experiments are performed to study the single-phase transient forced convection heat transfer on an array of four in-line, flush-mounted simulated electronic chips in a vertical rectangular channel. Water is the coolant media and the flow covers the wide range of laminar flow regime with Reynolds number, based on heat source length, from 800 to 2,625. The heat flux ranges from 1 W/cm2 to 7 W/cm2. The heat transfer characteristics are studied and correlations are presented. The transient correlation for overall data recommended is Nuℓ= 0.945(Peℓ 1/3) Fo-1/2.

  17. Influence of the convective surface transfer coefficients on the Heat, Air, and Moisture (HAM) building performance

    DEFF Research Database (Denmark)

    Steskens, Paul Wilhelmus Maria Hermanus; Janssen, Hans; Rode, Carsten

    2009-01-01

    Current models to predict heat, air and moisture (HAM) conditions in buildings assume constant boundary conditions for the temperature and relative humidity of the neighbouring air and for the surface heat and moisture transfer coefficients. These assumptions may introduce errors in the predicted...... HAM conditions. The paper focuses on the influence of the interior surface heat and moisture transfer coefficients, and investigates its effect on the hygrothermal performance. The parameter study showed that the magnitude of the convective surface transfer coefficients have a relatively large...... influence on the predicted hygrothermal conditions at the surface of a building component and on the heat and vapour exchange with the indoor environment....

  18. Industrial Application of Topology Optimization for Combined Conductive and Convective Heat Transfer Problems

    DEFF Research Database (Denmark)

    Zhou, Mingdong; Alexandersen, Joe; Sigmund, Ole

    2016-01-01

    This paper presents an industrial application of topology optimization for combined conductive and convective heat transfer problems. The solution is based on a synergy of computer aided design and engineering software tools from Dassault Systemes. The considered physical problem of steady...

  19. Numerical modelling of convective heat transport by air flow in permafrost talus slopes

    Science.gov (United States)

    Wicky, Jonas; Hauck, Christian

    2017-06-01

    Talus slopes are a widespread geomorphic feature in the Alps. Due to their high porosity a gravity-driven internal air circulation can be established which is forced by the gradient between external (air) and internal (talus) temperature. The thermal regime is different from the surrounding environment, leading to the occurrence of permafrost below the typical permafrost zone. This phenomenon has mainly been analysed by field studies and only few explicit numerical modelling studies exist. Numerical simulations of permafrost sometimes use parameterisations for the effects of convection but mostly neglect the influence of convective heat transfer in air on the thermal regime. In contrast, in civil engineering many studies have been carried out to investigate the thermal behaviour of blocky layers and to improve their passive cooling effect. The present study further develops and applies these concepts to model heat transfer in air flows in a natural-scale talus slope. Modelling results show that convective heat transfer has the potential to develop a significant temperature difference between the lower and the upper parts of the talus slope. A seasonally alternating chimney-effect type of circulation develops. Modelling results also show that this convective heat transfer leads to the formation of a cold reservoir in the lower part of the talus slope, which can be crucial for maintaining the frozen ground conditions despite increasing air temperatures caused by climate change.

  20. Mixed convective heat transfer from a vertical plate embedded in a ...

    Indian Academy of Sciences (India)

    In problems dealing with porous media, the effect of melting, radiation is important in indus- tries and technologies. The applications are found in situation such as geothermal systems, heating and cooling chamber, fossil fuel combustion, energy processes and Astro-physical flows. The effects of non-Darcy mixed convection ...

  1. Reappraising the Relationships between Physics Students' Mental Models and Predictions: An Example of Heat Convection

    Science.gov (United States)

    Chiou, Guo-Li

    2013-01-01

    Although prediction is claimed to be a prime function of mental models, to what extent students can run their mental models to make predictions of physical phenomena remains uncertain. The purpose of this study, therefore, was first to investigate 30 physics students' mental models of heat convection, and then to examine the relationship between…

  2. Mixed convection flow and heat transfer in a vertical wavy channel ...

    African Journals Online (AJOL)

    Mixed convection flow and heat transfer in a vertical wavy channel containing porous and fluid layer with traveling thermal waves. ... Results for a wide range of governing parameters such as Grashof number, viscosity ratio, width ratio, conductivity ratio, and traveling thermal temperature are plotted for different values of ...

  3. Adiabatic partition effect on natural convection heat transfer inside a square cavity

    DEFF Research Database (Denmark)

    Mahmoudi Nezhad, Sajjad; Rezaniakolaei, Alireza; yousefi, Tooraj

    2017-01-01

    A steady state and two-dimensional laminar free convection heat transfer in a partitioned cavity with horizontal adiabatic and isothermal side walls is investigated using both experimental and numerical approaches. The experiments and numerical simulations are carried out using a Mach-Zehnder int...

  4. Mixed convective heat transfer from a vertical plate embedded in a ...

    Indian Academy of Sciences (India)

    Home; Journals; Sadhana; Volume 40; Issue 2. Mixed convective heat transfer from a vertical plate embedded in a saturated non-Darcy porous medium with concentration and melting effect. K Hemalatha Peri K Kameswaran M V D N S Madhavi. Mechanical Sciences Volume 40 Issue 2 April 2015 pp 455-465 ...

  5. Use of Artificial Neural Networks for Prediction of Convective Heat Transfer in Evaporative Units

    Directory of Open Access Journals (Sweden)

    Romero-Méndez Ricardo

    2014-01-01

    Full Text Available Convective heat transfer prediction of evaporative processes is more complicated than the heat transfer prediction of single-phase convective processes. This is due to the fact that physical phenomena involved in evaporative processes are very complex and vary with the vapor quality that increases gradually as more fluid is evaporated. Power-law correlations used for prediction of evaporative convection have proved little accuracy when used in practical cases. In this investigation, neural-network-based models have been used as a tool for prediction of the thermal performance of evaporative units. For this purpose, experimental data were obtained in a facility that includes a counter-flow concentric pipes heat exchanger with R134a refrigerant flowing inside the circular section and temperature controlled warm water moving through the annular section. This work also included the construction of an inverse Rankine refrigeration cycle that was equipped with measurement devices, sensors and a data acquisition system to collect the experimental measurements under different operating conditions. Part of the data were used to train several neural-network configurations. The best neural-network model was then used for prediction purposes and the results obtained were compared with experimental data not used for training purposes. The results obtained in this investigation reveal the convenience of using artificial neural networks as accurate predictive tools for determining convective heat transfer rates of evaporative processes.

  6. Reinforcing Concepts of Transient Heat Conduction and Convection with Simple Experiments and COMSOL Simulations

    Science.gov (United States)

    Mendez, Sergio; AungYong, Lisa

    2014-01-01

    To help students make the connection between the concepts of heat conduction and convection to real-world phenomenon, we developed a combined experimental and computational module that can be incorporated into lecture or lab courses. The experimental system we present requires materials and apparatus that are readily accessible, and the procedure…

  7. An analytical solution to the one-dimensional heat conduction-convection equation in soil

    Science.gov (United States)

    Heat transfer in soil occurs by conduction and convection. Infiltrating water affects soil temperature distributions, and measuring soil temperature distributions below infiltrating water can provide a signal for the flux of water. In earlier work a sine wave function (hereinafter referred to as the...

  8. Thermal performance of a porus radial fin with natural convection and radiative heat losses

    Directory of Open Access Journals (Sweden)

    Darvishi M.T.

    2015-01-01

    Full Text Available An analytic (series solution is developed to describe the thermal performance of a porous radial fin with natural convection in the fluid saturating the fin and radiation heat loss from the top and bottom surfaces of the fin. The HAM results for the temperature distribution and base heat flux are compared with the direct numerical results and found to be very accurate.

  9. Novel Natural Convection Heat Sink Design Concepts From First Principles

    Science.gov (United States)

    2016-06-01

    effective f fluid ,m i mean mixing-cup at inlet ,m o mean mixing-cup at outlet open open boundary p pressure rad radiation s surface th...utilizing principles of the stack effect (i.e., using multiple inlets to create a suction effect to draw cooler ambient air into the tube). The second...of flow and heat transfer were carried out for constant temperature heat addition for single vertical tubes, multiple stacked tubes, tube system

  10. Study and Application of Forced Convection in Road Bus Heating System

    Directory of Open Access Journals (Sweden)

    Scheila Sandi Biazus

    2015-03-01

    Full Text Available This work deals with a replacing the heating system of intercity buses, made by long heat exchangers distributed on the sides of the passenger saloon by small and compact ones that use forced convection to heat dissipation. At the beginning the calculation was made of the heat capacity of a heat exchanger with the parameters defined by the supplier, and then conducted an analysis of change in these parameters in order to improve its efficiency. The method for examining the heat exchanger is based on the correlations available in the convection flow inside and outside to determine the respective convective coefficients, and therefore the overall coefficient of heat transfer. Following, the heat exchanger in its original form, was tested on bench. Thus, from the thermal load of the bus model studied, the amount of exchangers required has been defined to satisfy the thermal comfort of passengers. Field tests of the heating systems with new heat exchangers were performed to obtain actual data of the proposed system. The original factory system showed to be efficient in meeting the needs thermal load and economically viable, such that the critical thermal load can be met with ten heaters installed along the body. Furthermore, this system offers the possibility of varying the parameters to best fit to the project, where the flow variation of the fans or the spacing between the fins of the heat exchanger decreases the amount of heaters required. At the same time, the system showed the need for further study to assess its distribution along the passenger saloon in order to meet a best uniformity temperature distribution.

  11. β-distribution for Reynolds stress and turbulent heat flux in relaxation turbulent boundary layer of compression ramp

    Science.gov (United States)

    Hu, YanChao; Bi, WeiTao; Li, ShiYao; She, ZhenSu

    2017-12-01

    A challenge in the study of turbulent boundary layers (TBLs) is to understand the non-equilibrium relaxation process after sep-aration and reattachment due to shock-wave/boundary-layer interaction. The classical boundary layer theory cannot deal with the strong adverse pressure gradient, and hence, the computational modeling of this process remains inaccurate. Here, we report the direct numerical simulation results of the relaxation TBL behind a compression ramp, which reveal the presence of intense large-scale eddies, with significantly enhanced Reynolds stress and turbulent heat flux. A crucial finding is that the wall-normal profiles of the excess Reynolds stress and turbulent heat flux obey a β-distribution, which is a product of two power laws with respect to the wall-normal distances from the wall and from the boundary layer edge. In addition, the streamwise decays of the excess Reynolds stress and turbulent heat flux also exhibit power laws with respect to the streamwise distance from the corner of the compression ramp. These results suggest that the relaxation TBL obeys the dilation symmetry, which is a specific form of self-organization in this complex non-equilibrium flow. The β-distribution yields important hints for the development of a turbulence model.

  12. Combined influence of unsteady free stream velocity and free stream turbulence on stagnation point heat transfer

    Science.gov (United States)

    Gorla, R. S. R.

    1984-01-01

    An analysis is presented to study the combined effects of transient free stream velocity and free stream turbulence on heat transfer at a stagnation point over a cylinder situated in a crossflow. An expression for the eddy diffusivity has been formulated and the governing momentum and energy equations are integrated by means of the steepest descent method. The numerical results for the heat transfer rate are correlated by a turbulence parameter. It has been found that the stagnation point heat transfer rate increases with increasing free stream turbulence intensity.

  13. Feedback control and heat transfer measurements in a Rayleigh-Bénard convection cell

    Science.gov (United States)

    Vial, M.; Hernández, R. H.

    2017-07-01

    We report experimental results on the heat transfer and instability onset of a Rayleigh-Bénard convection cell of aspect ratios 6:3:1 filled with a high Prandtl aqueous solution of glycerol under feedback control. We investigate the transient and stationary response of both local temperature readings and heat transfer fluxes on the Rayleigh Bénard cell in both conductive and convective states when we perform two independent feedback control actions on both hot and cold walls. We evaluate the performance of both controllers to maintain a temperature gradient independently if the system is below or above the convection threshold. As the convection cell can be rotated at 180° about the shorter axis of the cell, it was possible to perform transitions between thermal conduction and convection regimes and vice versa under a constant temperature difference maintained by both independent controllers. The experimental setup provided an accurate measurement of the critical Rayleigh number and the evolution of the Nusselt number as a function of the Rayleigh number in the moderately supercritical regime (R a formed by 6 transverse rolls throughout the range of Rayleigh numbers.

  14. Heat Transfer and Convective Structure of Evaporating Films under Pressure-Modulated Conditions

    Science.gov (United States)

    Gonzalez, Juan Carlos

    This work examines the fluid mechanical and heat transfer characteristics of evaporating films under cyclical superheat conditions. This research was motivated by the need to further understand the instability drivers in films undergoing unsteady and cyclical evaporation. The superheat was controlled modulating the system pressure. An isolated test cell allowed the films to evaporate into their own vapor without non-condensable present. A non-intrusive thickness measurement technique was used to yield dynamic heat flux measurements. A double pass schlieren system was employed to capture convective structures. System temperature and pressure measurements completed the diagnostics. The primary conclusions are briefly summarized as follows: • The evolution of thermal profile within evaporating films has a strong impact on the development of convective structure and heat transfer. In some cases convective structure appears within the film under pressure-modulated conditions even when the evaporation intervals are sufficiently short that conduction is expected to be the only heat transfer mode within the film. • Convective structure appears to persist in many cases even after evaporation is stopped. • Stopping the evaporation for short time intervals appears to have a negligible effect on the temperature profile in the film based on the subsequent evaporation behavior. • Complex, multi-wavelength convective structure behavior can be induced through cyclical superheating of the films. • A modest gain in short-term heat flux is achievable under some pressure-modulated conditions. • Surface instabilities of quasi-steady evaporating films do not lead to an increase in the evaporation rate. • Reduced gravity tests were seriously compromised by unsteady g-levels and g-jitter.

  15. Entropy Generation Analysis of Natural Convection in Square Enclosures with Two Isoflux Heat Sources

    Directory of Open Access Journals (Sweden)

    S. Z. Nejad

    2017-04-01

    Full Text Available This study investigates entropy generation resulting from natural convective heat transfer in square enclosures with local heating of the bottom and symmetrical cooling of the sidewalls. This analysis tends to optimize heat transfer of two pieces of semiconductor in a square electronic package. In this simulation, heaters are modeled as isoflux heat sources and sidewalls of the enclosure are isothermal heat sinks. The top wall and the non-heated portions of the bottom wall are adiabatic. Flow and temperature fields are obtained by numerical simulation of conservation equations of mass, momentum and energy in laminar, steady and two dimensional flows. With constant heat energy into the cavity, effect of Rayleigh number, heater length, heater strength ratios and heater position is evaluated on flow and temperature fields and local entropy generation. The results show that a minimum entropy generation rate is obtained under the same condition in which a minimum peak heater temperature is obtained.

  16. Research of heat transfer of staggered horizontal bundles of finned tubes at free air convection

    Science.gov (United States)

    Novozhilova, A. V.; Maryna, Z. G.; Samorodov, A. V.; Lvov, E. A.

    2017-11-01

    The study of free-convective processes is important because of the cooling problem in many machines and systems, where other ways of cooling are impossible or impractical. Natural convective processes are common in the steam turbine air condensers of electric power plants located within the city limits, in dry cooling towers of circulating water systems, in condensers cooled by air and water, in radiators cooling oil of power electric transformers, in emergency cooling systems of nuclear reactors, in solar power, as well as in air-cooling of power semiconductor energy converters. All this makes actual the synthesis of the results of theoretical and experimental research of free convection for heat exchangers with finned tube bundles. The results of the study of free-convection heat transfer for two-, three- and four-row staggered horizontal bundles of industrial bimetallic finned tubes with finning factor of 16.8 and equilateral tubes arrangement are presented. Cross and diagonal steps in the bundles are the same: 58; 61; 64; 70; 76; 86; 100 mm, which corresponds to the relative steps: 1.042; 1.096; 1.152; 1.258; 1.366; 1.545; 1.797. These steps are standardized for air coolers. An equation for calculating the free-convection heat transfer, taking into account the influence of geometrical parameters in the range of Rayleigh number from 30,000 to 350,000 with an average deviation of ± 4.8%, has been obtained. The relationship presented in the article allows designing a wide range of air coolers for various applications, working in the free convection modes.

  17. Bibliography on augmentation of convective heat and mass transfer

    Energy Technology Data Exchange (ETDEWEB)

    Bergles, A.E.; Webb, R.L.; Junkhan, G.H.; Jensen, M.K.

    1979-05-01

    Heat transfer augmentation has developed into a major specialty area in heat transfer research and development. A bibliography of world literature on augmentation is presented. The literature is classified into passive augmentation techniques, which require no external power, and active techniques, which do require external power. The fourteen techniques are grouped in terms of their application to the various modes of heat transfer. Mass transfer is included for completeness. Key words are included with each citation for technique/mode identification. The total number of publications cited is 1,967, including 75 surveys of various techniques and 42 papers on performance evaluation of passive techniques. Patents are not included as they will be the subject of a future topical report.

  18. Comprehensive Analysis of Convective Heat Transfer in Parallel Plate Microchannel with Viscous Dissipation and Constant Heat Flux Boundary Conditions

    Science.gov (United States)

    Kushwaha, Hari Mohan; Sahu, Santosh Kumar

    2017-10-01

    This paper reports the hydrodynamically and thermally fully developed, laminar, incompressible, forced convective heat transfer characteristics of gaseous flows through a parallel plate microchannel with different constant heat flux boundary conditions. The first order velocity slip and viscous dissipation effects are considered in the analysis. Here, three different thermal boundary conditions such as: both plates kept at different constant heat fluxes, both plates kept at equal constant heat fluxes and one plate kept at constant heat flux and other one insulated are considered for the analysis. The deviation in Nusselt number between the model that considers both first order velocity slip and temperature jump and the one that considers only velocity slip is reported. Also, the effect of various heat flux ratios on the Nusselt number is reported in this analysis. In addition, the deviation in Nusselt number between first and second order slip model is discussed in this study.

  19. Convection in a nematic liquid crystal with homeotropic alignment and heated from below

    Energy Technology Data Exchange (ETDEWEB)

    Ahlers, G. [Univ. of California, Santa Barbara, CA (United States)

    1995-12-31

    Experimental results for convection in a thin horizontal layer of a homeotropically aligned nematic liquid crystal heated from below and in a vertical magnetic field are presented. A subcritical Hopf bifurcation leads to the convecting state. There is quantitative agreement between the measured and the predicted bifurcation line as a function of magnetic field. The nonlinear state near the bifurcation is one of spatio-temporal chaos which seems to be the result of a zig-zag instability of the straight-roll state.

  20. Critical heat flux for free convection boiling in thin rectangular channels

    Science.gov (United States)

    Cheng, Lap Y.; Tichler, P. R.

    A review of the experimental data on free convection boiling critical heat flux (CHF) in vertical rectangular channels reveals three mechanisms of burnout. They are the pool boiling limit, the circulation limit, and the flooding limit associated with a transition in flow regime from churn to annular flow. The dominance of a particular mechanism depends on the dimensions of the channel. Analytical models were developed for each free convection boiling limit. Limited agreement with data is observed. A CHF correlation, which is valid for a wide range of gap sizes, was constructed from the CHF's calculated according to the three mechanisms of burnout.

  1. Reappraising the relationships between physics students’ mental models and predictions: An example of heat convection

    Directory of Open Access Journals (Sweden)

    Guo-Li Chiou

    2013-05-01

    Full Text Available Although prediction is claimed to be a prime function of mental models, to what extent students can run their mental models to make predictions of physical phenomena remains uncertain. The purpose of this study, therefore, was first to investigate 30 physics students’ mental models of heat convection, and then to examine the relationship between their mental models and predictions of convection-related phenomena. A series of semistructured interviews was conducted to probe the participants’ mental models and predictions of heat convection, and the constant comparative method was adopted for data analysis. The results reveal that the participants held a variety of mental models of heat convection, and nearly half held flawed mental models rather than a scientifically compatible one. In addition, while many participants attempted to run their mental models to make a prediction at the beginning stage of solving an interview problem, the relationship between the models and predictions became increasingly complex as the problem solving process continued. The relationships between mental models and predictions, however, could be better understood by considering the completeness of a mental model, the scale of analyzing mental models, and the retrieval of different formats of mental representations.

  2. Linear Stability Analysis of Penetrative Convection via Internal Heating in a Ferrofluid Saturated Porous Layer

    Directory of Open Access Journals (Sweden)

    Amit Mahajan

    2017-05-01

    Full Text Available Penetrative convection due to purely internal heating in a horizontal ferrofluid-saturated porous layer is examined by performing linear stability analysis. Four different types of heat supply functions are considered. The Darcy model is used to incorporate the effect of the porous medium. Numerical solutions are obtained by using the Chebyshev pseudospectral method, and the results are discussed for all three boundary conditions: when both boundaries are impermeable and conducting; when both boundaries are conducting with lower boundary impermeable and free upper boundary; and when both boundaries are impermeable with lower boundary conducting and upper with constant heat flux. The effect of the Langevin parameter, width of ferrofluid layer, permeability parameter, and nonlinearity of the fluid magnetization has been observed at the onset of penetrative convection for water- and ester-based ferrofluids. It is seen that the Langevin parameter, width of ferrofluid layer, and permeability parameter have stabilizing effects on the onset of convection, while the nonlinearity of the fluid magnetization advances the onset of convection.

  3. Transient natural convection heat and mass transfer in crystal growth

    Science.gov (United States)

    Han, Samuel S.

    1990-01-01

    A numerical analysis of transient combined heat and mass transfer across a rectangular cavity is performed. The physical parameters are selected to represent a range of possible crystal growth in solutions. Good agreements with measurement data are observed. It is found that the thermal and solute fields become highly oscillatory when the thermal and solute Grashof numbers are large.

  4. Variable viscosity effects on mixed convection heat and mass ...

    African Journals Online (AJOL)

    An analysis is carried out to study the viscous dissipation and variable viscosity effects on the flow, heat and mass transfer characteristics in a viscous fluid over a semi-infinite vertical porous plate in the presence of chemical reaction. The governing boundary layer equations are written into a dimensionless form by similarity ...

  5. Time-Dependent Natural Convection Couette Flow of Heat ...

    African Journals Online (AJOL)

    Laplace transform techniques is used to obtain the analytical solutions for the temperature and the velocity profiles while the rate of heat transfer as well the skin friction are consequently derived. The numerical simulation conducted for some saturated liquids reveled that at t ≥ Pr the steady and unsteady state velocities (as ...

  6. Heat transfers in a double-skin roof ventilated by natural convection in summer time

    CERN Document Server

    Biwole, Pascal; Pompeo, C

    2013-01-01

    The double-skin roofs investigated in this paper are formed by adding a metallic screen on an existing sheet metal roof. The system enhances passive cooling of dwellings and can help diminishing power costs for air conditioning in summer or in tropical and arid countries. In this work, radiation, convection and conduction heat transfers are investigated. Depending on its surface properties, the screen reflects a large amount of oncoming solar radiation. Natural convection in the channel underneath drives off the residual heat. The bi-dimensional numerical simulation of the heat transfers through the double skin reveals the most important parameters for the system's efficiency. They are, by order of importance, the sheet metal surface emissivity, the screen internal and external surface emissivity, the insulation thickness and the inclination angle for a channel width over 6 cm. The influence of those parameters on Rayleigh and Nusselt numbers is also investigated. Temperature and air velocity profiles on seve...

  7. Numerical study of combined convection heat transfer for thermally developing upward flow in a vertical cylinder

    Directory of Open Access Journals (Sweden)

    Mohammed Hussein A.

    2008-01-01

    Full Text Available The problem of the laminar upward mixed convection heat transfer for thermally developing air flow in the entrance region of a vertical circular cylinder under buoyancy effect and wall heat flux boundary condition has been numerically investigated. An implicit finite difference method and the Gauss elimination technique have been used to solve the governing partial differential equations of motion (Navier Stocks equations for two-dimensional model. This investigation covers Reynolds number range from 400 to 1600, heat flux is varied from 70 W/m2 to 400 W/m2. The results present the dimensionless temperature profile, dimensionless velocity profile, dimensionless surface temperature along the cylinder, and the local Nusselt number variation with the dimensionless axial distance Z+. The dimensionless velocity and temperature profile results have revealed that the secondary flow created by natural convection have a significant effect on the heat transfer process. The results have also shown an increase in the Nusselt number values as the heat flux increases. The results have been compared with the available experimental study and with the available analytical solution for pure forced convection in terms of the local Nusselt number. The comparison has shown satisfactory agreement. .

  8. Influence of sea ice lead-width distribution on turbulent heat transfer between the ocean and the atmosphere

    Directory of Open Access Journals (Sweden)

    S. Marcq

    2012-02-01

    Full Text Available Leads are linear-like structures of open water within the sea ice cover that develop as the result of fracturing due to divergence or shear. Through leads, air and water come into contact and directly exchange latent and sensible heat through convective processes driven by the large temperature and moisture differences between them. In the central Arctic, leads only cover 1 to 2% of the ocean during winter, but account for more than 70% of the upward heat fluxes. Furthermore, narrow leads (several meters are more than twice as efficient at transmitting turbulent heat than larger ones (several hundreds of meters. We show that lead widths are power law distributed, P(X~X−a with a>1, down to very small spatial scales (20 m or below. This implies that the open water fraction is by far dominated by very small leads. Using two classical formulations, which provide first order turbulence closure for the fetch-dependence of heat fluxes, we find that the mean heat fluxes (sensible and latent over open water are up to 55% larger when considering the lead-width distribution obtained from a SPOT satellite image of the ice cover, compared to the situation where the open water fraction constitutes one unique large lead and the rest of the area is covered by ice, as it is usually considered in climate models at the grid scale. This difference may be even larger if we assume that the power law scaling of lead widths extends down to smaller (~1 m scales. Such estimations may be a first step towards a subgrid scale parameterization of the spatial distribution of open water for heat fluxes calculations in ocean/sea ice coupled models.

  9. Radiative heat transfer in turbulent combustion systems theory and applications

    CERN Document Server

    Modest, Michael F

    2016-01-01

    This introduction reviews why combustion and radiation are important, as well as the technical challenges posed by radiation. Emphasis is on interactions among turbulence, chemistry and radiation (turbulence-chemistry-radiation interactions – TCRI) in Reynolds-averaged and large-eddy simulations. Subsequent chapters cover: chemically reacting turbulent flows; radiation properties, Reynolds transport equation (RTE) solution methods, and TCRI; radiation effects in laminar flames; TCRI in turbulent flames; and high-pressure combustion systems. This Brief presents integrated approach that includes radiation at the outset, rather than as an afterthought. It stands as the most recent developments in physical modeling, numerical algorithms, and applications collected in one monograph.

  10. Study on transition between heat conduction and convection using particle methods

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, Tadashi; Kaburaki, Hideo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1996-09-01

    The Rayleigh-Benard system is simulated using the direct simulation Monte Carlo method and the molecular dynamics method, which are the representative particle methods, and the transition phenomena between heat conduction and convection is studied from the microscopic level. The critical Rayleigh number obtained by the direct simulation Monte Carlo method, which is a statistical technique, agrees with that obtained by the linear stability analysis of hydrodynamic equations, and it is shown that the macroscopic flow instability can be studied quantitatively using the microscopic particle method. The correlations of fluctuations of temperature and velocity are found to grow at the transition in comparison with those at obvious conduction or convection states. The motions of atoms are studied using the molecular dynamics method, which is a deterministic technique, in terms of Lyapunov exponents. It is found that the chaotic motions of atoms are increased when the convection rolls, which are large-scale ordered motions of atoms, appear in the flow field. (author)

  11. Distributed Roughness Effects on Blunt-Body Transition and Turbulent Heating

    Science.gov (United States)

    Hollis, Brian R.

    2014-01-01

    An experimental program has been conducted to obtain data on the effects of surface roughness on blunt bodies at laminar, transitional, and turbulent conditions. Wind tunnel models with distributed surface roughness heights from 0.06 mm to 1.75 mm were tested and heating data were obtained using global surface thermography. Heating rates of up to 85% higher than predicted, smooth-surface turbulent levels were measured.

  12. Salt tectonics and shallow subseafloor fluid convection: Models of coupled fluid-heat-salt transport

    Science.gov (United States)

    Wilson, A.; Ruppel, C.

    2007-01-01

    Thermohaline convection associated with salt domes has the potential to drive significant fluid flow and mass and heat transport in continental margins, but previous studies of fluid flow associated with salt structures have focused on continental settings or deep flow systems of importance to petroleum exploration. Motivated by recent geophysical and geochemical observations that suggest a convective pattern to near-seafloor pore fluid flow in the northern Gulf of Mexico (GoMex), we devise numerical models that fully couple thermal and chemical processes to quantify the effects of salt geometry and seafloor relief on fluid flow beneath the seafloor. Steady-state models that ignore halite dissolution demonstrate that seafloor relief plays an important role in the evolution of shallow geothermal convection cells and that salt at depth can contribute a thermal component to this convection. The inclusion of faults causes significant, but highly localized, increases in flow rates at seafloor discharge zones. Transient models that include halite dissolution show the evolution of flow during brine formation from early salt-driven convection to later geothermal convection, characteristics of which are controlled by the interplay of seafloor relief and salt geometry. Predicted flow rates are on the order of a few millimeters per year or less for homogeneous sediments with a permeability of 10−15 m2, comparable to compaction-driven flow rates. Sediment permeabilities likely fall below 10−15 m2 at depth in the GoMex basin, but such thermohaline convection can drive pervasive mass transport across the seafloor, affecting sediment diagenesis in shallow sediments. In more permeable settings, such flow could affect methane hydrate stability, seafloor chemosynthetic communities, and the longevity of fluid seeps.

  13. Free convection flow of some fractional nanofluids over a moving vertical plate with uniform heat flux and heat source

    Science.gov (United States)

    Azhar, Waqas Ali; Vieru, Dumitru; Fetecau, Constantin

    2017-08-01

    Free convection flow of some water based fractional nanofluids over a moving infinite vertical plate with uniform heat flux and heat source is analytically and graphically studied. Exact solutions for dimensionless temperature and velocity fields, Nusselt numbers, and skin friction coefficients are established in integral form in terms of modified Bessel functions of the first kind. These solutions satisfy all imposed initial and boundary conditions and reduce to the similar solutions for ordinary nanofluids when the fractional parameters tend to one. Furthermore, they reduce to the known solutions from the literature when the plate is fixed and the heat source is absent. The influence of fractional parameters on heat transfer and fluid motion is graphically underlined and discussed. The enhancement of heat transfer in such flows is higher for fractional nanofluids in comparison with ordinary nanofluids. Moreover, the use of fractional models allows us to choose the fractional parameters in order to get a very good agreement between experimental and theoretical results.

  14. Conjugate Heat Transfer of Mixed Convection for Viscoelastic Fluid Past a Stretching Sheet

    Directory of Open Access Journals (Sweden)

    Kai-Long Hsiao

    2007-01-01

    Full Text Available A conjugate heat transfer problem of a second-grade viscoelastic fluid past a stretching sheet has been studied. Governing equations include heat conduction equation of a stretching sheet, continuity equation, momentum equation, and energy equation of a second-grade fluid, analyzed by a combination of a series expansion method, the similarity transformation, and a second-order accurate finite-difference method. These solutions are used to iterate with the heat conduction equation of the stretching sheet to obtain distributions of the local convective heat transfer coefficient and the stretching sheet temperature. Ranges of dimensionless parameters, the Prandtl number Pr, the elastic number E and the conduction-convection coefficient Ncc are from 0.001 to 10, 0.0001 to 0.01, and 0.5 to 2.0, respectively. A parameter G, which is used to represent the dominance of the buoyant effect, is present in governing equations. Results indicated that elastic effect in the flow could increase the local heat transfer coefficient and enhance the heat transfer of a stretching sheet. In addition, same as the results from Newtonian fluid flow and conduction analysis of a stretching sheet, a better heat transfer is obtained with a larger Ncc, G, and E.

  15. Link between von-Karman energy decay and reconnection heating in turbulent plasmas

    Science.gov (United States)

    Shay, M. A.; Parashar, T.; Haggerty, C. C.; Matthaeus, W. H.; Phan, T.; Drake, J. F.; Cassak, P.; Wu, P.

    2016-12-01

    Coherent structures such as current sheets are prevalent in many turbulent plasmas and have been shown to be correlated with dissipation and heating in observations of solar wind turbulence and dissipation in kinetic particle-in-cell (PIC) simulations. However, the role that they play in the dissipation of turbulent energy and ultimately the heating of the plasma are still not well understood. A recent study [1] using kinetic PIC simulations of turbulence found that the total heating in the plasma is consistent with a von-Karman scaling of the cascade rate, and that the proton to electron heating ratio was proportional to the total heating rate and linked to the ratio of gyroperiod to nonlinear turnover time at the ion kinetic scales. We review recent findings regarding the rate of heating in outflow jets during laminar reconnection and apply it to kinetic PIC simulations of turbulence, employing some reasonable assumptions to connect the two theories. The goal is to determine if reconnection is a primary heating mechanism or plays less of a role. Conversely, we also apply the new understanding of the von-Karman cascade to isolated reconnection events to determine if a cascade-like process is controlling the heating rate. [1] W. Matthaeus et al., ApJ Letters, 827, L7, 2016, doi:10.3847/2041-8205/827/1/L7

  16. Numerical Studies on Natural Convection Heat Losses from Open Cubical Cavities

    Directory of Open Access Journals (Sweden)

    M. Prakash

    2013-01-01

    Full Text Available The natural convection heat losses occurring from cubical open cavities are analysed in this paper. Open cubical cavities of sides 0.1 m, 0.2 m, 0.25 m, 0.5 m, and 1 m with constant temperature back wall boundary conditions and opening ratio of 1 are studied. The Fluent CFD software is used to analyse the three-dimensional (3D cavity models. The studies are carried out for cavities with back wall temperatures between 35°C and 100°C. The effect of cavity inclination on the convective loss is analysed for angles of 0° (cavity facing sideways, 30°, 45°, 60°, and 90° (cavity facing vertically downwards. The Rayleigh numbers involved in this study range between 4.5 × 105 and 1.5 × 109. The natural convection loss is found to increase with an increase in back wall temperature. The natural convection loss is observed to decrease with an increase in cavity inclination; the highest convective loss being at 0° and the lowest at 90° inclination. This is observed for all cavities analysed here. Nusselt number correlations involving the effect of Rayleigh number and the cavity inclination angle have been developed from the current studies. These correlations can be used for engineering applications such as electronic cooling, low- and medium-temperature solar thermal systems, passive architecture, and also refrigeration systems.

  17. Mixed convection heat transfer from confined tandem square cylinders in a horizontal channel

    KAUST Repository

    Huang, Zhu

    2013-11-01

    This paper presents a numerical study on the two-dimensional laminar mixed convective flow and heat transfer around two identical isothermal square cylinders arranged in tandem and confined in a channel. The spacing between the cylinders is fixed with four widths of the cylinder and the blockage ratio and the Prandtl number are fixed at 0.1 and 0.7 respectively. The mixed convective flow and heat transfer is simulated by high accuracy multidomain pseudospectral method. The Reynolds number (Re) is studied in the range 80 ≤ Re ≤ 150, the Richardson number (Ri) demonstrating the influence of thermal buoyancy ranges from 0 to 1. Numerical results reveal that, with the thermal buoyancy effect, the mixed convective flow sheds vortex behind the cylinders and keeps periodic oscillating. The variations of characteristic quantities related to flow and heat transfer processes, such as the overall drag and lift coefficients and the Nusselt numbers, are presented and discussed. Furthermore, the influence of thermal buoyancy on the fluid flow and heat transfer are discussed and analysed. © 2013 Elsevier Ltd. All rights reserved.

  18. Numerical Modeling of Conjugate Thermogravitational Convection in a Closed System with a Radiant Energy Source in Conditions of Convective-Radiative Heat Exchange at the External Boundary

    Directory of Open Access Journals (Sweden)

    Nee Alexander

    2016-01-01

    Full Text Available Mathematical modeling of conjugate natural convection in a closed rectangular cavity with a radiant energy source in conditions of convective-radiative heat exchange at the external boundary was conducted. The radiant energy distribution was set by the Lambert’s law. Conduction and convection processes analysis showed that the air masses flow pattern is modified slightly over the time. The temperature increases in the gas cavity, despite the heat removal from the one of the external boundary. According to the results of the integral heat transfer analysis were established that the average Nusselt number (Nuav increasing occurs up to τ = 200 (dimensionless time. Further Nuav has changed insignificantly due to the temperature field equalization near the interfaces “gas – wall”.

  19. Sensory quality and energy use for scrambled eggs and beef patties heated in institutional microwave and convection ovens

    Energy Technology Data Exchange (ETDEWEB)

    Cremer, M.L.

    1982-05-01

    Scrambled eggs (96 portions) and beef patties (96 portions) were heated in institutional microwave and convection ovens to determine energy use in heating and sensory quality of food. For both products, significantly (P < 0.01) more energy (BTU) was used for heating in the convection than in the microwave oven and respective amounts (BTU) were 28658.7 and 9385.7 for eggs; 31313.3 and 9365.0 for beef patties. All scores for sensory quality were significantly (P < 0.01) higher for eggs heated in the microwave than in the convection, but for beef patties, scores were higher for all characteristics and significantly (P < 0.01) higher for appearance, flavor, and general acceptability after heating in the convection rather than the microwave oven.

  20. Self-consistent viscous heating of rapidly compressed turbulence

    Science.gov (United States)

    Campos, Alejandro; Morgan, Brandon; Olson, Britton; Greenough, Jeffrey

    2016-11-01

    Given turbulence subjected to infinitely rapid deformations, linear terms representing interactions between the mean flow and the turbulence dictate the flow evolution, whereas non-linear terms corresponding to turbulence-turbulence interactions are safely ignored. For rapidly deformed flows where the turbulence Reynolds number is not sufficiently large, viscous effects can't be neglected and tend to play a prominent role, as shown in Davidovits & Fisch (2016). For such a case, the rapid increase of viscosity in a plasma-as compared to the weaker scaling of viscosity in a fluid-leads to the sudden viscous dissipation of turbulent kinetic energy. As described in Davidovits & Fisch, increases in temperature caused by the direct compression of the plasma drive sufficiently large values of viscosity. We report on numerical simulations of turbulence where the increase in temperature is the result of both the direct compression (an inviscid mechanism) and the self-consistent viscous transfer of energy from the turbulent scales towards the thermal energy. A comparison between implicit large-eddy simulations against well-resolved direct numerical simulations is included to asses the effect of the numerical and subgrid-scale dissipation on the self-consistent viscous energy transfer. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

  1. Laminar mixed convection heat and mass transfer in an isothermally cooled channel

    Energy Technology Data Exchange (ETDEWEB)

    Oulaid, O. [Laboratoire de Mecanique des Fluides et d Energetique, Marrakech (Morocco). Dept. of Physics; Sherbrooke Univ., PQ (Canada). Dept. of Mechanical Engineering; Benhamou, B. [Laboratoire de Mecanique des Fluides et d Energetique, Marrakech (Morocco). Dept. of Physics; Galanis, N. [Sherbrooke Univ., PQ (Canada). Dept. of Mechanical Engineering

    2009-07-01

    Many studies have been performed to investigate the combined effects of thermal and mass buoyancy forces in channel convection. This paper presented a numerical study of a laminar mixed convection associated with phase change in an isothermally cooled vertical parallel-plate channel. The plates were wetted by a thin liquid water film and maintained at a constant temperature lower than that of the air entering the channel. The paper discussed the use of an elliptical model, including axial diffusion of momentum, heat and mass transfer. The paper also presented the solution of the governing equations using the finite volume method with the simpler algorithm for handling the velocity-pressure coupling. Cases of film evaporation and vapor condensation were also considered. In order to to bring out the effects of buoyancy forces, results from mixed convection case and forced convection were compared. A comparative evaluation showed that these forces, mostly of thermal origin, decelerate the flow near the walls and induce flow reversal for high temperatures, thus reducing heat and mass transfer. 17 refs., 1 tab., 6 figs.

  2. Radio frequency heating induced edge plasma convection: self-consistent simulations and experiments on ASDEX Upgrade

    Science.gov (United States)

    Zhang, W.; Tierens, W.; Noterdaeme, J.-M.; Bobkov, V.; Aguiam, D.; Coster, D.; Fuenfgelder, H.; Jacquot, J.; Ochoukov, R.; Silva, A.; Colas, L.; Křivská, A.; the ASDEX Upgrade Team; the MST1 Team

    2017-11-01

    Plasma heating with waves in the ion cyclotron range of frequency (ICRF) affects the edge plasma and the edge plasma affects the ICRF heating. In simulations, these nonlinear ICRF—edge plasma interactions have been self-consistently simulated by running the EMC3-EIRENE, RAPLICASOL and SSWICH codes in an iterative way on ASDEX Upgrade for the first time. In experiments, the edge plasma convection induced by powered 3-strap antennas is measured with the antenna embedded reflectometers for the first time. Both the simulation and experimental results indicate that the ICRF induced convective cells are most significant on the top and bottom of the antennas; the edge plasma convection induced by 3-strap antennas in optimized antenna feeding configuration (dipole phasing, power ratio between the center and outer straps ~1.5) is smallest among the studied cases. The simulation results also suggest that compared to the 2-strap antennas, the 3-strap antennas can significantly reduce the plasma convection associated with the radio-frequency sheaths, even with unfavorable power balance between the straps in dipole phasing.

  3. On oscillatory convection with the Cattaneo–Christov hyperbolic heat-flow model

    Science.gov (United States)

    Bissell, J. J.

    2015-01-01

    Adoption of the hyperbolic Cattaneo–Christov heat-flow model in place of the more usual parabolic Fourier law is shown to raise the possibility of oscillatory convection in the classic Bénard problem of a Boussinesq fluid heated from below. By comparing the critical Rayleigh numbers for stationary and oscillatory convection, Rc and RS respectively, oscillatory convection is found to represent the preferred form of instability whenever the Cattaneo number C exceeds a threshold value CT≥8/27π2≈0.03. In the case of free boundaries, analytical approaches permit direct treatment of the role played by the Prandtl number P1, which—in contrast to the classical stationary scenario—can impact on oscillatory modes significantly owing to the non-zero frequency of convection. Numerical investigation indicates that the behaviour found analytically for free boundaries applies in a qualitatively similar fashion for fixed boundaries, while the threshold Cattaneo number CT is computed as a function of P1∈[10−2,10+2] for both boundary regimes. PMID:25792960

  4. EXPERIMENTAL INVESTIGATION OF NATURAL CONVECTION HEAT TRANSFER OF IONIC LIQUID IN A RECTANGULAR ENCLOSURE HEATED FROM BELOW

    Energy Technology Data Exchange (ETDEWEB)

    Fox, E.; Visser, A.; Bridges, N.

    2011-07-18

    This paper presents an experimental study of natural convection heat transfer for an Ionic Liquid. The experiments were performed for 1-butyl-2, 3-dimethylimidazolium bis(trifluoromethylsulfonyl)imide, ([C{sub 4}mmim][NTf{sub 2}]) at a Raleigh number range of 1.26 x 10{sup 7} to 8.3 x 10{sup 7}. In addition to determining the convective heat transfer coefficients, this study also included experimental determination of thermophysical properties of [C{sub 4}mmim][NTf{sub 2}] such as, density, viscosity, heat capacity, and thermal conductivity. The results show that the density of [C{sub 4}mmim][NTf{sub 2}] varies from 1.437-1.396 g/cm{sup 3} within the temperature range of 10-50 C, the thermal conductivity varies from 0.105-0.116 W/m.K between a temperature of 10 to 60 C, the heat capacity varies from 1.015 J/g.K - 1.760 J/g.K within temperature range of 25-340 C and the viscosity varies from 18cp-243cp within temperature range 10-75 C. The results for density, thermal conductivity, heat capacity, and viscosity were in close agreement with the values in the literature. Measured dimensionless Nusselt number was observed to be higher for the ionic liquid than that of DI water. This is expected as Nusselt number is the ratio of heat transfer by convection to conduction and the ionic liquid has lower thermal conductivity (approximately 18%) than DI water.

  5. Fluid flow and heat convection studies for actively cooled airframes

    Science.gov (United States)

    Mills, A. F.

    This report details progress made on the jet impingement - liquid crystal - digital imaging experiment. With the design phase complete, the experiment is currently in the construction phase. In order to reach this phase two design related issues were resolved. The first issue was to determine NASP leading edge active cooling design parameters. Meetings were arranged with personnel at SAIC International, Torrance, CA in order to obtain recent publications that characterized expected leading edge heat fluxes as well as other details of NASP operating conditions. The information in these publications was used to estimate minimum and maximum jet Reynolds numbers needed to accomplish the required leading edge cooling, and to determine the parameters of the experiment. The details of this analysis are shown in Appendix A. One of the concerns for the NASP design is that of thermal stress due to large surface temperature gradients. Using a series of circular jets to cool the leading edge will cause a non-uniform temperature distribution and potentially large thermal stresses. Therefore it was decided to explore the feasibility of using a slot jet to cool the leading edge. The literature contains many investigations into circular jet heat transfer but few investigations of slot jet heat transfer. The first experiments will be done on circular jets impinging on a fiat plate and results compared to previously published data to establish the accuracy of the method. Subsequent experiments will be slot jets impinging on full scale models of the NASP leading edge. Table 1 shows the range of parameters to be explored. Next a preliminary design of the experiment was done. Previous papers which used a similar experimental technique were studied and elements of those experiments adapted to the jet impingement study. Trade-off studies were conducted to determine which design was the least expensive, easy to construct, and easy to use. Once the final design was settled, vendors were

  6. Convective heat transfer in foams under laminar flow in pipes and tube bundles.

    Science.gov (United States)

    Attia, Joseph A; McKinley, Ian M; Moreno-Magana, David; Pilon, Laurent

    2012-12-01

    The present study reports experimental data and scaling analysis for forced convection of foams and microfoams in laminar flow in circular and rectangular tubes as well as in tube bundles. Foams and microfoams are pseudoplastic (shear thinning) two-phase fluids consisting of tightly packed bubbles with diameters ranging from tens of microns to a few millimeters. They have found applications in separation processes, soil remediation, oil recovery, water treatment, food processes, as well as in fire fighting and in heat exchangers. First, aqueous solutions of surfactant Tween 20 with different concentrations were used to generate microfoams with various porosity, bubble size distribution, and rheological behavior. These different microfoams were flowed in uniformly heated circular tubes of different diameter instrumented with thermocouples. A wide range of heat fluxes and flow rates were explored. Experimental data were compared with analytical and semi-empirical expressions derived and validated for single-phase power-law fluids. These correlations were extended to two-phase foams by defining the Reynolds number based on the effective viscosity and density of microfoams. However, the local Nusselt and Prandtl numbers were defined based on the specific heat and thermal conductivity of water. Indeed, the heated wall was continuously in contact with a film of water controlling convective heat transfer to the microfoams. Overall, good agreement between experimental results and model predictions was obtained for all experimental conditions considered. Finally, the same approach was shown to be also valid for experimental data reported in the literature for laminar forced convection of microfoams in rectangular minichannels and of macrofoams across aligned and staggered tube bundles with constant wall heat flux.

  7. Characteristic analysis of turbulent heat diffusion in a multi-compartment structure; Takukakuka kukan kozo ni okeru ranryunetsu kakusan gensho no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Hu, C.; Fukuchi, N. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1997-10-01

    An analysis was made on turbulent heat diffusion in a multi-compartment structure necessary for designing calorific power and environment for functional systems used in marine vessels and off-shore structures. In a multi-compartment structure, the diffusion phenomenon is complex because of movement of air flow in turbulence and buoyancy resulted from non-isothermal condition. The phenomenon is largely affected by space shapes and walls, and the conditions in heat diffusion field is governed also by shapes of opening connecting the compartments. An analysis was made by using the SIMPLE method on turbulent heat diffusion in a multi-compartment space with high Raleigh number in which natural convection is dominant. If the opening is small, the Coanda effect appears, in which air flow passing through the opening rises along the wall, wherein a high-temperature layer is formed near the ceiling, making the heat diffusion inactive. If the opening is large, a jetting flow from the opening and a large circulating flow are created, which cause active advection mixture, making temperature gradient smaller in the upper layer. Heat transfer intensity in an opening on a partition wall decays in proportion with 1/4th power of the opening ratio. 7 refs., 11 figs.

  8. Optimal wall spacing for heat transport in thermal convection

    Energy Technology Data Exchange (ETDEWEB)

    Shishkina, Olga [Max Planck Institute for Dynamics and Self-Organization, Goettingen (Germany)

    2016-11-01

    The simulation of RB flow for Ra up to 1 x 10{sup 10} is computationally expensive in terms of computing power and hard disk storage. Thus, we gratefully acknowledge the computational resources supported by Leibniz-Rechenzentrum Munich. Compared to Γ=1 situation, a new physical picture of heat transport is identified here at Γ{sub opt} for any explored Ra. Therefore, a detailed comparison between Γ=1 and Γ=Γ{sub opt} is valuable for our further research, for example, their vertical temperature and velocity profiles. Additionally, we plan to compare the fluid with different Pr under geometrical confinement, which are computationally expensive for the situations of Pr<<1 and Pr>>1.

  9. A new correlation for convective heat transfer coefficient of water–alumina nanofluid in a square array subchannel under PWR condition

    Energy Technology Data Exchange (ETDEWEB)

    Shamim, Jubair A. [Department of Nuclear Engineering, Seoul National University, Seoul 08826 (Korea, Republic of); Department of Mechanical Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Bhowmik, Palash K. [Department of Nuclear Engineering, Seoul National University, Seoul 08826 (Korea, Republic of); Department of Nuclear Engineering, Missouri University of Science and Technology, 1201 N. State St., Rolla, MO 65409 (United States); Xiangyi, Chen [Department of Nuclear Engineering, Seoul National University, Seoul 08826 (Korea, Republic of); Suh, Kune Y., E-mail: kysuh@snu.ac.kr [Department of Nuclear Engineering, Seoul National University, Seoul 08826 (Korea, Republic of)

    2016-11-15

    Highlights: • Thermo-hydrodynamic properties of water–Al{sub 2}O{sub 3} nanofluid at PWR condition is analyzed. • Details of CFD simulation and validation procedure is outlined. • Augmented heat transfer capacity of nanofluid is governed by larger pumping power. • A new correlation for nanofluid Nusselt number in subchannel geometry is proposed. - Abstract: The computational fluid dynamic (CFD) simulation is performed to determine on the thermo- and hydrodynamic performance of the water–alumina (Al{sub 2}O{sub 3}) nanofluid in a square array subchannel featuring pitch-to-diameter ratios of 1.25 and 1.35. Two fundamental aspects of thermal hydraulics, viz. heat transfer and pressure drop, are assessed under typical pressurized water reactor (PWR) conditions at various flow rates (3 × 10{sup 5} ⩽ Re ⩽ 6 × 10{sup 5}) using pure water and differing concentrations of water–alumina nanofluid (0.5–3.0 vol.%) as coolant. Numerical results are compared against predictions made by conventional single-phase convective heat transfer and pressure loss correlations for fully developed turbulent flow. It is observed that addition of tiny nanoparticles in PWR coolant can give rise to the convective heat transfer coefficient at the expense of larger pressure drop. Nevertheless, a modified correlation as a function of nanoparticle volume fraction is proposed to estimate nanofluid Nusselt number more precisely in square array subchannel.

  10. Thermal-diffusion effects on mixed convection flow in a heat absorbing fluid with Newtonian heating and chemical reaction

    Science.gov (United States)

    Hussanan, Abid; Salleh, Mohd Zuki; Tahar, Razman Mat; Khan, Ilyas

    2015-02-01

    Thermal-diffusion and chemical reaction effects on mixed convection heat and mass transfer flow past an infinite oscillating vertical plate with Newtonian heating is investigated. The governing equations are transformed to a system of linear partial differential equations using appropriate non-dimensional variables. Using Laplace transform method the resulting equations are solved analytically and the expression for velocity, temperature and concentration are obtained. They satisfy all imposed initial and boundary conditions. Numerical results for temperature and concentration are shown in various graphs for embedded flow parameters and discussed in details.

  11. Absorption of intense microwaves and ion acoustic turbulence due to heat transport

    Energy Technology Data Exchange (ETDEWEB)

    De Groot, J.S.; Liu, J.M. [California Univ., Davis, CA (United States); Matte, J.P. [INRS-Energie (Canada)] [and others

    1994-02-04

    Measurements and calculations of the inverse bremsstrahlung absorption of intense microwaves are presented. The isotropic component of the electron distribution becomes flat-topped in agreement with detailed Fokker-Planck calculations. The plasma heating is reduced due to the flat-topped distributions in agreement with calculations. The calculations show that the heat flux at high microwave powers is very large, q{sub max} {approx} 0.3 n{sub e}v{sub e}T{sub e}. A new particle model to, calculate the heat transport inhibition due to ion acoustic turbulence in ICF plasmas is also presented. One-dimensional PIC calculations of ion acoustic turbulence excited due to heat transport are presented. The 2-D PIC code is presently being used to perform calculations of heat flux inhibition due to ion acoustic turbulence.

  12. Assessment of Haar Wavelet-Quasilinearization Technique in Heat Convection-Radiation Equations

    Directory of Open Access Journals (Sweden)

    Umer Saeed

    2014-01-01

    Full Text Available We showed that solutions by the Haar wavelet-quasilinearization technique for the two problems, namely, (i temperature distribution equation in lumped system of combined convection-radiation in a slab made of materials with variable thermal conductivity and (ii cooling of a lumped system by combined convection and radiation are strongly reliable and also more accurate than the other numerical methods and are in good agreement with exact solution. According to the Haar wavelet-quasilinearization technique, we convert the nonlinear heat transfer equation to linear discretized equation with the help of quasilinearization technique and apply the Haar wavelet method at each iteration of quasilinearization technique to get the solution. The main aim of present work is to show the reliability of the Haar wavelet-quasilinearization technique for heat transfer equations.

  13. Measurements of laminar mixed convection flow adjacent to an inclined surface with uniform wall heat flux

    Energy Technology Data Exchange (ETDEWEB)

    Abu-Mulaweh, H.I. [Mechanical Engineering Department, Purdue University at Fort Wayne, 2101 E. Coliseum Blvd., 46805, Fort Wayne, IN (United States)

    2003-01-01

    Measurements of laminar mixed convection flow adjacent to an inclined heated flat plate with uniform wall heat flux are reported. Laser-doppler velocimeter and cold wire anemometer were used to measure simultaneously the velocity and temperature distributions, respectively. Measurements of the air velocity and temperature distributions are presented for a range of buoyancy parameters 0{<=}{xi}{<=}2.91. It was found that both the mixed convection local Nusselt number and local friction coefficient increase as the buoyancy force increases (under the buoyancy assisting condition). The velocity field was found to be more sensitive to the buoyancy force than the thermal field. Predictions from both local similarity and local non-similarity models agree well with the experimental results for the thermal field, but only the predictions from the local non-similarity model agree favorably with the measured values for the flow field. (authors)

  14. CFD Study on Wall/Nanoparticle Interaction in Nanofluids Convective Heat Transfer

    Directory of Open Access Journals (Sweden)

    Mohammad Reza Tarybakhsh

    2013-01-01

    Full Text Available The Brownian motion of the nanoparticles in nanofluid is one of the potential contributors to enhance effective thermal conductivity and the mechanisms that might contribute to this enhancement are the subject of considerable discussion and debate. In this paper, the mixing effect of the base fluid in the immediate vicinity of the nanoparticles caused by the Brownian motion was analyzed, modeled, and compared with existing experimental data available in the literature. CFD was developed to study the effect of wall/nanoparticle interaction on forced convective heat transfer in a tube under constant wall temperature condition. The results showed that the motion of the particle near the wall which can decrease boundary layer and the hydrodynamics effects associated with the Brownian motion have a significant effect on the convection heat transfer of nanofluid.

  15. A note on convective heat transfer of an MHD Jeffrey fluid over a stretching sheet

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, Jawad; Shahzad, Azeem [Department of Basic Sciences, University of Engineering and Technology, Taxila 47050 (Pakistan); Khan, Masood [Department of Mathematics, Quaid-i-Azam University, Islamabad 44000 (Pakistan); Ali, Ramzan, E-mail: alian.qau@gmail.com [Department of Applied Mathematics, TU-Dortmund (Germany); University of Central Asia, 720001 Bishkek (Kyrgyzstan)

    2015-11-15

    This article focuses on the exact solution regarding convective heat transfer of a magnetohydrodynamic (MHD) Jeffrey fluid over a stretching sheet. The effects of joule and viscous dissipation, internal heat source/sink and thermal radiation on the heat transfer characteristics are taken in account in the presence of a transverse magnetic field for two types of boundary heating process namely prescribed power law surface temperature (PST) and prescribed heat flux (PHF). Similarity transformations are used to reduce the governing non-linear momentum and thermal boundary layer equations into a set of ordinary differential equations. The exact solutions of the reduced ordinary differential equations are developed in the form of confluent hypergeometric function. The influence of the pertinent parameters on the temperature profile is examined. In addition the results for the wall temperature gradient are also discussed in detail.

  16. A note on convective heat transfer of an MHD Jeffrey fluid over a stretching sheet

    Directory of Open Access Journals (Sweden)

    Jawad Ahmed

    2015-11-01

    Full Text Available This article focuses on the exact solution regarding convective heat transfer of a magnetohydrodynamic (MHD Jeffrey fluid over a stretching sheet. The effects of joule and viscous dissipation, internal heat source/sink and thermal radiation on the heat transfer characteristics are taken in account in the presence of a transverse magnetic field for two types of boundary heating process namely prescribed power law surface temperature (PST and prescribed heat flux (PHF. Similarity transformations are used to reduce the governing non-linear momentum and thermal boundary layer equations into a set of ordinary differential equations. The exact solutions of the reduced ordinary differential equations are developed in the form of confluent hypergeometric function. The influence of the pertinent parameters on the temperature profile is examined. In addition the results for the wall temperature gradient are also discussed in detail.

  17. Nonlinear thermal convection in a layer of nanofluid under G-jitter and internal heating effects

    Directory of Open Access Journals (Sweden)

    Bhadauria B. S.

    2014-01-01

    Full Text Available This paper deals with a mathematical model of controlling heat transfer in nanofluids. The time-periodic vertical vibrations of the system are considered to effect an external control of heat transport along with internal heating effects. A weakly non-linear stability analysis is based on the five-mode Lorenz model using which the Nusselt number is obtained as a function of the thermal Rayleigh number, nano-particle concentration based Rayleigh number, Prandtl number, Lewis number, modified diffusivity ratio, amplitude and frequency of modulation. It is shown that modulation can be effectively used to control convection and thereby heat transport. Further, it is found that the effect of internal Rayleigh number is to enhance the heat and nano-particles transport.

  18. Comparison of microwave and conduction-convection heating autohydrolysis pretreatment for bioethanol production.

    Science.gov (United States)

    Aguilar-Reynosa, Alejandra; Romaní, Aloia; Rodríguez-Jasso, Rosa M; Aguilar, Cristóbal N; Garrote, Gil; Ruiz, Héctor A

    2017-11-01

    This work describes the application of two forms of heating for autohydrolysis pretreatment on isothermal regimen: conduction-convection heating and microwave heating processing using corn stover as raw material for bioethanol production. Pretreatments were performed using different operational conditions: residence time (10-50 min) and temperature (160-200°C) for both pretreatments. Subsequently, the susceptibility of pretreated solids was studied using low enzyme loads, and high substrate loads. The highest conversion was 95.1% for microwave pretreated solids. Also solids pretreated by microwave heating processing showed better ethanol conversion in simultaneous saccharification and fermentation process (92% corresponding to 33.8g/L). Therefore, microwave heating processing is a promising technology in the pretreatment of lignocellulosic materials. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Lie Group Analysis of Natural Convective Flow from a Convectively Heated Upward Facing Radiating Permeable Horizontal Plate in Porous Media Filled with Nanofluid

    Directory of Open Access Journals (Sweden)

    Md. Jashim Uddin

    2012-01-01

    Full Text Available Two-dimensional, steady, laminar and incompressible natural convective flow of a nanofluid over a connectively heated permeable upward facing radiating horizontal plate in porous medium is studied numerically. The present model incorporates Brownian motion and thermophoresis effects. The similarity transformations for the governing equations are developed by Lie group analysis. The transformed equations are solved numerically by Runge-Kutta-Fehlberg fourth-fifth order method with shooting technique. Effects of the governing parameters on the dimensionless velocity, temperature and nanoparticle volume fraction as well as on the dimensionless rate of heat and mass transfer are presented graphically and the results are compared with the published data for special cases. Good agreement is found between numerical results of the present paper and published results. It is found that Lewis number, Brownian motion and convective heat transfer parameters increase the heat and mass transfer rates whilst thermophoresis decreases both heat and mass transfer rates.

  20. Al/ oil nanofluids inside annular tube: an experimental study on convective heat transfer and pressure drop

    Science.gov (United States)

    Jafarimoghaddam, Amin; Aberoumand, Sadegh; Javaherdeh, Kourosh; Arani, Ali Akbar Abbasian; Jafarimoghaddam, Reza

    2017-10-01

    In this work, an experimental study on nanofluid preparation stability, thermo-physical properties, heat transfer performance and friction factor of Al/ Oil nanofluids has been carried out. Electrical Explosion Wire (E.E.W) which is one of the most reliable one-step techniques for nanofluids preparation has been used. An annular tube has been considered as the test section in which the outer tube was subject to a uniform heat flux boundary condition of about 204 W. The utilized nanofluids were prepared in three different volume concentrations of 0.011%, 0.044% and 0.171%. A wide range of parameters such as Reynolds number Prandtl number, viscosity, thermal conductivity, density, specific heat, convective heat transfer coefficient, Nusselt number and the friction factor have been studied. The experiment was conducted in relatively low Reynolds numbers of less than 160 and within a hydrodynamically fully-developed regime. According to the results, thermal conductivity, density and viscosity increased depending on the volume concentrations and working temperatures while the specific heat declined. More importantly, it was observed that convective heat transfer coefficient and Nusselt number enhanced by 28.6% and 16.4%, respectively, for the highest volume concentration. Finally, the friction factor (which plays an important role in the pumping power) was found to be increased around 18% in the volume fraction of 0.171%.

  1. Fundamental Study of Local Heat Transfer in Forced Convective Boiling of Ammonia on Vertical Flat Plate

    Science.gov (United States)

    Kim, Jeong-Hun; Arima, Hirofumi; Ikegami, Yasuyuki

    In the present study, the fundamental experiments that investigate characteristics of local heat transfer in forced convective boiling on vertical flat plate with 2-mm channel height are taken to realize plate type compact evaporator for OTEC or STEC. The experiments are performed with ammonia as the working fluid. The experiments are also carried out with the following test conditions; saturated pressure = 0.7, 0.8, 0.9 MPa, mass flux = 7.5, 10, 15 kg/(m2•s), heat flux = 15, 20, 25 kW/m2 and inlet quality = 0.1 ~ 0.4 [-]. The result shows that the wall superheated temperature of forced convective boiling is lower than that of pool boiling. And the heat transfer coefficient increases with an increase in quality and the decrease in the local heat flux and saturated pressure for prescribed experimental conditions. However, local heat transfer coefficients are not affected by mass fluxes in the prescribed experimental conditions. An empirical correlation that can predict the local heat transfer coefficient on vertical flat plate within experimental conditions is also proposed.

  2. Magnetohydrodynamic free convection heat and mass transfer of a heat generating fluid past an impulsively started infinite vertical porous plate with Hall current and radiation absorption

    Energy Technology Data Exchange (ETDEWEB)

    Kinyanjui, M.; Kwanza, J.K.; Uppal, S.M. [Jomo Kenyatta University of Agriculture and Technology, Nairobi (Cayman Islands). Dept. of Mathematics and Statistics

    2001-05-01

    Simultaneous heat and mass transfer in unsteady free convection flow with radiation absorption past an impulsively started infinite vertical porous plate subjected to a strong magnetic field is presented. The governing equations for the problem are solved by a finite difference scheme. The influence of the various parameters on the convectively cooled or convectively heated plate in the laminar boundary layer are considered. An analysis of the effects of the parameters on the concentration, velocity and temperature profiles, as well as skin friction and the rates of mass and heat transfer, is done with the aid of graphs and tables. (author)

  3. Numerical Investigation of Heat Transfer Enhancement in a Rectangular Heated Pipe for Turbulent Nanofluid

    Directory of Open Access Journals (Sweden)

    Hooman Yarmand

    2014-01-01

    Full Text Available Thermal characteristics of turbulent nanofluid flow in a rectangular pipe have been investigated numerically. The continuity, momentum, and energy equations were solved by means of a finite volume method (FVM. The symmetrical rectangular channel is heated at the top and bottom at a constant heat flux while the sides walls are insulated. Four different types of nanoparticles Al2O3, ZnO, CuO, and SiO2 at different volume fractions of nanofluids in the range of 1% to 5% are considered in the present investigation. In this paper, effect of different Reynolds numbers in the range of 5000 < Re < 25000 on heat transfer characteristics of nanofluids flowing through the channel is investigated. The numerical results indicate that SiO2-water has the highest Nusselt number compared to other nanofluids while it has the lowest heat transfer coefficient due to low thermal conductivity. The Nusselt number increases with the increase of the Reynolds number and the volume fraction of nanoparticles. The results of simulation show a good agreement with the existing experimental correlations.

  4. A p-version finite element method for steady incompressible fluid flow and convective heat transfer

    Science.gov (United States)

    Winterscheidt, Daniel L.

    1993-01-01

    A new p-version finite element formulation for steady, incompressible fluid flow and convective heat transfer problems is presented. The steady-state residual equations are obtained by considering a limiting case of the least-squares formulation for the transient problem. The method circumvents the Babuska-Brezzi condition, permitting the use of equal-order interpolation for velocity and pressure, without requiring the use of arbitrary parameters. Numerical results are presented to demonstrate the accuracy and generality of the method.

  5. Enhanced convective heat transfer using graphene dispersed nanofluids

    Directory of Open Access Journals (Sweden)

    Baby Tessy

    2011-01-01

    Full Text Available Abstract Nanofluids are having wide area of application in electronic and cooling industry. In the present work, hydrogen exfoliated graphene (HEG dispersed deionized (DI water, and ethylene glycol (EG based nanofluids were developed. Further, thermal conductivity and heat transfer properties of these nanofluids were systematically investigated. HEG was synthesized by exfoliating graphite oxide in H2 atmosphere at 200°C. The nanofluids were prepared by dispersing functionalized HEG (f-HEG in DI water and EG without the use of any surfactant. HEG and f-HEG were characterized by powder X-ray diffractometry, electron microscopy, Raman and FTIR spectroscopy. Thermal and electrical conductivities of f-HEG dispersed DI water and EG based nanofluids were measured for different volume fractions and at different temperatures. A 0.05% volume fraction of f-HEG dispersed DI water based nanofluid shows an enhancement in thermal conductivity of about 16% at 25°C and 75% at 50°C. The enhancement in Nusselts number for these nanofluids is more than that of thermal conductivity.

  6. Integral transform solution of natural convection in a square cavity with volumetric heat generation

    Directory of Open Access Journals (Sweden)

    C. An

    2013-12-01

    Full Text Available The generalized integral transform technique (GITT is employed to obtain a hybrid numerical-analytical solution of natural convection in a cavity with volumetric heat generation. The hybrid nature of this approach allows for the establishment of benchmark results in the solution of non-linear partial differential equation systems, including the coupled set of heat and fluid flow equations that govern the steady natural convection problem under consideration. Through performing the GITT, the resulting transformed ODE system is then numerically solved by making use of the subroutine DBVPFD from the IMSL Library. Therefore, numerical results under user prescribed accuracy are obtained for different values of Rayleigh numbers, and the convergence behavior of the proposed eigenfunction expansions is illustrated. Critical comparisons against solutions produced by ANSYS CFX 12.0 are then conducted, which demonstrate excellent agreement. Several sets of reference results for natural convection with volumetric heat generation in a bi-dimensional square cavity are also provided for future verification of numerical results obtained by other researchers.

  7. Convection Heat Transfer Modeling of Ag Nanofluid Using Different Viscosity Theories

    Directory of Open Access Journals (Sweden)

    Ali Bakhsh Kasaeian

    2012-04-01

    Full Text Available ABSTRACT: In this paper, the effects of adding nanoparticles (including Ag to a fluid media for improving free convection heat transfer were analysed. The free convective heat transfer was assumed to be in laminar flow regime, and the corresponding calculations and solutions were all done by the integral method. Water, as a Newtonian fluid, was considered as the base and all relevant thermo physical properties of the nanofluids were considered to be unvarying. The calculations performed and the graphs generated showed that, in general, the addition of nanoparticles to the fluid media resulted in an increment or improvement of its heat transfer coefficient. With increase in the concentration of the nanoparticles, the heat transfer rate of the fluid also increased. The increment in heat transfer is also dependent on the nanoparticles’ thermal conductivity and the viscosity theory which was utilized in the calculations. In this study, four different theories were used to calculate the viscosities of the nanofluids. The effects of viscosity on the nanofluids’ thermal conductivity were apparent from the calculations which were performed for nanoparticle concentrations of 4% or less. ABSTRAK: Kajian ini menganalisis kesan penambahan nanopartikel Ag ke dalam media bendalir bagi tujuan pembaikkan pemindahan haba perolakan bebas. Perolakan bebas diandaikan berada di zon aliran laminar, di mana penyelesaian dan pengiraan telah dilakukan mengunakan kaedah kamilan. Air yang merupakan cecair Newtonian, dianggap sebagai asas dan sifat terma fizikal nanocecair dianggapkan tidak berubah. Mengikut pengiraan yang dilakukan dan graf yang diplotkan, umumnya penambahan nanopartikel kepada media bendalir menyebabkan peningkatan dan pengembangan pekali pemindahan haba. Kadar pemindahan haba meningkat dengan nanopartikel. Peningkatan pemindahan haba juga bergantung kepada pengalir haba nanopartikel dan teori kelikatan yang digunakan. Di dalam kajian ini, empat

  8. A study of natural convection cooling of multiple discrete heat sources in a vertical channel

    Science.gov (United States)

    Willson, Thomas D.

    1988-06-01

    Natural convection liquid cooling of simulated electronic components in a vertical channel was investigated. The test surface contained a single column of eight rectangular, protruding heated elements, each simulating a 20 pin dual-in-line package. Temperature measurements and flow visualization were performed for a number of power dissipation levels and channel widths. Collectively, this information was used in interpreting the flow and transport characteristics. A correlation to predict the heat transfer rates was developed based on the component surface temperatures. Optimum channel widths were determined from these surface temperature measurements for the range of power levels investigated. Temperature distributions in the fluid were measured using a traversing thermocouple probe.

  9. Analytical solutions for tomato peeling with combined heat flux and convective boundary conditions

    Science.gov (United States)

    Cuccurullo, G.; Giordano, L.; Metallo, A.

    2017-11-01

    Peeling of tomatoes by radiative heating is a valid alternative to steam or lye, which are expensive and pollutant methods. Suitable energy densities are required in order to realize short time operations, thus involving only a thin layer under the tomato surface. This paper aims to predict the temperature field in rotating tomatoes exposed to the source irradiation. Therefore, a 1D unsteady analytical model is presented, which involves a semi-infinite slab subjected to time dependent heating while convective heat transfer takes place on the exposed surface. In order to account for the tomato rotation, the heat source is described as the positive half-wave of a sinusoidal function. The problem being linear, the solution is derived following the Laplace Transform Method. In addition, an easy-to-handle solution for the problem at hand is presented, which assumes a differentiable function for approximating the source while neglecting convective cooling, the latter contribution turning out to be negligible for the context at hand. A satisfying agreement between the two analytical solutions is found, therefore, an easy procedure for a proper design of the dry heating system can be set up avoiding the use of numerical simulations.

  10. Combined Influence of Strain and Heat Loss on Turbulent Premixed Flame Stabilization

    KAUST Repository

    Tay-Wo-Chong, Luis

    2015-11-16

    The present paper argues that the prediction of turbulent premixed flames under non-adiabatic conditions can be improved by considering the combined effects of strain and heat loss on reaction rates. The effect of strain in the presence of heat loss on the consumption speed of laminar premixed flames was quantified by calculations of asymmetric counterflow configurations (“fresh-to-burnt”) with detailed chemistry. Heat losses were introduced by setting the temperature of the incoming stream of products on the “burnt” side to values below those corresponding to adiabatic conditions. The consumption speed decreased in a roughly exponential manner with increasing strain rate, and this tendency became more pronounced in the presence of heat losses. An empirical relation in terms of Markstein number, Karlovitz Number and a non-dimensional heat loss parameter was proposed for the combined influence of strain and heat losses on the consumption speed. Combining this empirical relation with a presumed probability density function for strain in turbulent flows, an attenuation factor that accounts for the effect of strain and heat loss on the reaction rate in turbulent flows was deduced and implemented into a turbulent combustion model. URANS simulations of a premixed swirl burner were carried out and validated against flow field and OH chemiluminescence measurements. Introducing the effects of strain and heat loss into the combustion model, the flame topology observed experimentally was correctly reproduced, with good agreement between experiment and simulation for flow field and flame length.

  11. Heat Transfer Enhancement in a Channel with Rib-Groove Turbulators

    Science.gov (United States)

    Kaewkohkiat, Y.; Kongkaitpaiboon, V.; Eiamsa-ard, S.; Pimsarn, M.

    2010-03-01

    This paper presents the effects of the rib-groove turbulators on the heat transfer and friction characteristics in a rectangular channel. The experiments encompass the Reynolds number range from 1800 to 10,000; pitch ratios (PR = P/e) 6.6-13.3 by using air as the working fluid. The obtained results demonstrate that heat transfer rate in term of Nusselt number (Nu) increases with the increase of Reynolds number, whereas friction factor (f) shows the opposite trend. Both Nusselt number and friction factor increase with decreasing pitch ratio. It is also observed that heat transfer rate and friction factor for the channels with rib-groove turbulators are higher than those for the smooth channel under similar test conditions. In addition, the correlations for heat transfer rate in term of Nusselt number (Nu) and friction factor (f) for channel with rib-groove turbulators are also presented.

  12. Measuring convective heat transfer coefficients of nanofluids over a circular fine wire maintaining a constant temperature

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Shinpyo [Kyonggi Univ., Suwon (Korea, Republic of)

    2012-01-15

    This paper describes a measuring apparatus that can be used to appraise the effectiveness of nanofluids as new heat transfer enhancing fluids. A couple of apparatuses using fine hot wires as sensors have been proposed for this purpose; however, they have a technical weakness related to the uncertain working conditions of the sensor. The present method used the convective heat transfer coefficient from a hot wire as an indication of the heat transfer effectiveness of the nanofluid, where the temperature of the wire remains constant during the experiment. The operating principle and experimental procedure are explained in detail, and the validity of the system is tested with pure base fluids. The effects of particle concentration, velocity, and temperature on the heat transfer coefficients of the nanofluids are discussed comprehensively using the experimental data for graphite nanolubrication oil.

  13. Characterization of fluid flow patterns and heat transfer in horizontal channel mixed convection

    Energy Technology Data Exchange (ETDEWEB)

    Benderradji, A. [University of Batna, Department of Mechanical Engineering, Batna (Algeria); Haddad, A.; Taher, R.; Medale, M.; Abid, C.; Papini, F. [Technopole de Chateau-Gombert, IUSTI-CNRS UMR 6595, Polytech' Marseille, Marseille (France)

    2008-10-15

    Two mechanisms of roll initiation are highlighted in a horizontal channel flow, uniformly heated from below, at constant heat flux ({gamma}=10, Pr=7, 50{<=}Re{<=}100, 0{<=}Ra{<=}10{sup 6}). The first mechanism is the classical one, it occurs for low Rayleigh numbers and is initiated by the lateral wall effect. The second occurs for higher Rayleigh numbers and combines the previous effect with a supercritical vertical temperature gradient in the lower boundary layer, which simultaneously triggers pairs of rolls in the whole zone in between the two lateral rolls. We have found that in the present configuration, the transition between the two roll initiation mechanisms occurs for Ra/Re{sup 2} {approx}18. Consequently, the heat transfer is significantly enhanced compared to the pure forced convection case owing to the flow pattern responsible of the continuous flooding the heated wall with cold fluid. (orig.)

  14. Convective heat transfer from rotating disks subjected to streams of air

    CERN Document Server

    aus der Wiesche, Stefan

    2016-01-01

    This Brief describes systematically results of research studies on a series of convective heat transfer phenomena from rotating disks in air crossflow. Phenomena described in this volume were investigated experimentally using an electrically heated disk placed in the test section of a wind tunnel. The authors describe findings in which transitions between different heat transfer regimes can occur in dependency on the involved Reynolds numbers and the angle of incidence, and that these transitions could be related to phenomenological Landau and Landau-de Gennes models. The concise volume closes a substantial gap in the scientific literature with respect to flow and heat transfer in rotating disk systems and provides a comprehensive presentation of new and recent results not previously published in book form.

  15. Numerical Investigation of Heat Transfer Enhancement in a Rectangular Heated Pipe for Turbulent Nanofluid

    Science.gov (United States)

    Kazi, Salim Newaz; Sadeghinezhad, Emad

    2014-01-01

    Thermal characteristics of turbulent nanofluid flow in a rectangular pipe have been investigated numerically. The continuity, momentum, and energy equations were solved by means of a finite volume method (FVM). The symmetrical rectangular channel is heated at the top and bottom at a constant heat flux while the sides walls are insulated. Four different types of nanoparticles Al2O3, ZnO, CuO, and SiO2 at different volume fractions of nanofluids in the range of 1% to 5% are considered in the present investigation. In this paper, effect of different Reynolds numbers in the range of 5000 channel is investigated. The numerical results indicate that SiO2-water has the highest Nusselt number compared to other nanofluids while it has the lowest heat transfer coefficient due to low thermal conductivity. The Nusselt number increases with the increase of the Reynolds number and the volume fraction of nanoparticles. The results of simulation show a good agreement with the existing experimental correlations. PMID:25254236

  16. Convective and Stratiform Precipitation Processes and their Relationship to Latent Heating

    Science.gov (United States)

    Tao, Wei-Kuo; Lang, Steve; Zeng, Xiping; Shige, Shoichi; Takayabu, Yukari

    2009-01-01

    The global hydrological cycle is central to the Earth's climate system, with rainfall and the physics of its formation acting as the key links in the cycle. Two-thirds of global rainfall occurs in the Tropics. Associated with this rainfall is a vast amount of heat, which is known as latent heat. It arises mainly due to the phase change of water vapor condensing into liquid droplets; three-fourths of the total heat energy available to the Earth's atmosphere comes from tropical rainfall. In addition, fresh water provided by tropical rainfall and its variability exerts a large impact upon the structure and motions of the upper ocean layer. An improved convective -stratiform heating (CSH) algorithm has been developed to obtain the 3D structure of cloud heating over the Tropics based on two sources of information: 1) rainfall information, namely its amount and the fraction due to light rain intensity, observed directly from the Precipitation Radar (PR) on board the TRMM satellite and 2) synthetic cloud physics information obtained from cloud-resolving model (CRM) simulations of cloud systems. The cloud simulations provide details on cloud processes, specifically latent heating, eddy heat flux convergence and radiative heating/cooling, that. are not directly observable by satellite. The new CSH algorithm-derived heating has a noticeably different heating structure over both ocean and land regions compared to the previous CSH algorithm. One of the major differences between new and old algorithms is that the level of maximum cloud heating occurs 1 to 1.5 km lower in the atmosphere in the new algorithm. This can effect the structure of the implied air currents associated with the general circulation of the atmosphere in the Tropics. The new CSH algorithm will be used provide retrieved heating data to other heating algorithms to supplement their performance.

  17. Development, validation and application of an effective convectivity model for simulation of melt pool heat transfer in a light water reactor

    Energy Technology Data Exchange (ETDEWEB)

    Tran, Chi Thanh

    2007-12-15

    Severe accidents in a Light Water Reactor (LWR) have been a subject of the research for the last three decades. The research in this area aims to further understanding of the inherent physical phenomena and reduce the uncertainties surrounding their quantification, with the ultimate goal of developing models that can be applied to safety analysis of nuclear reactors. The research is also focusing on evaluation of the proposed accident management schemes for mitigating the consequences of such accidents. During a hypothetical severe accident, whatever the scenario, there is likelihood that the core material will be relocated and accumulated in the lower plenum in the form of a debris bed or a melt pool. Physical phenomena involved in a severe accident progression are complex. The interactions of core debris or melt with the reactor structures depend very much on the debris bed or melt pool thermal hydraulics. That is why predictions of heat transfer during melt pool formation in the reactor lower head are important for the safety assessment. The main purpose of the present study is to advance a method for describing turbulent natural convection heat transfer of a melt pool, and to develop a computational platform for cost-effective, sufficiently-accurate numerical simulations and analyses of Core Melt-Structure-Water Interactions in the LWR lower head during a postulated severe core-melting accident. Given the insights gained from Computational Fluid Dynamics (CFD) simulations, a physics-based model and computationally-efficient tools are developed for multi-dimensional simulations of transient thermal-hydraulic phenomena in the lower plenum of a Boiling Water Reactor (BWR) during the late phase of an in-vessel core melt progression. A model is developed for the core debris bed heat up and formation of a melt pool in the lower head of the reactor vessel, and implemented in a commercial CFD code. To describe the natural convection heat transfer inside the

  18. Conjugate heat transfer of laminar mixed convection of a nanofluid through an inclined tube with circumferentially non-uniform heating

    Directory of Open Access Journals (Sweden)

    Sarvari Seyed

    2011-01-01

    Full Text Available Abstract Laminar mixed convection of a nanofluid consisting of water and Al2O3 in an inclined tube with heating at the top half surface of a copper tube has been studied numerically. The bottom half of the tube wall is assumed to be adiabatic (presenting a tube of a solar collector. Heat conduction mechanism through the tube wall is considered. Three-dimensional governing equations with using two-phase mixture model have been solved to investigate hydrodynamic and thermal behaviours of the nanofluid over wide range of nanoparticle volume fractions. For a given nanoparticle mean diameter the effects of nanoparticle volume fractions on the hydrodynamics and thermal parameters are presented and discussed at different Richardson numbers and different tube inclinations. Significant augmentation on the heat transfer coefficient as well as on the wall shear stress is seen.

  19. Natural Convection Heat and Mass Transfer from Falling Films in Vertical Channels

    Science.gov (United States)

    Buck, Gregory Allen

    1990-01-01

    In the design of solar collector/regenerators for use in open cycle absorption refrigeration (OCAR) units, the problem of predicting evaporation rates and solution temperatures is of paramount importance in determining overall cycle performance. This transport of heat and mass is dominated by natural convection with buoyant forces primarily generated as a result of film heating by the solar flux, but aided by the evaporation of water (the lighter species) into the rising moist air stream. In order to better understand the mechanism of these combined buoyant interactions, the governing equations for natural convection flow in a vertical channel bounded by a heated falling film (simulating a glazed collector/regenerator) were solved using several different finite difference techniques. The numerical results were validated against existing experimental and numerical results for simplified boundary conditions. The appropriate nondimensionalization for the falling film boundary condition was established, ostensibly for the first time, and a parametric study for an air-water vapor mixture has been presented. Curve fits to the numerical results were determined for engineering design applications. To further confirm the validity of the numerical solutions, an experimental apparatus was constructed using electric resistance heat to simulate the constant heat flux of the solar source. Water was introduced at the top of this heated vertical surface at various flow rates and under various supplied heat fluxes, and a natural convection channel flow generated between the heated falling film and a parallel, plexiglass surface. Film temperatures and moist air velocity profiles were measured at various streamwise (vertical) locations for comparison with the numerical results. In general, measured film temperatures were 15 to 20 percent lower than the predicted values, but came to within 3 percent of the predictions when experimental uncertainty was incorporated into the numerical

  20. Enhancement of the forced convective heat transfer on mini pin fin heat sinks with micro spiral fins

    Science.gov (United States)

    Khonsue, Osot

    2017-09-01

    This research is an experimental study on the characteristics of heat transfer and pressure drop in mini heat sinks using air as the working fluid. The experiments were performed under a constant heat flux ranging from 9.132-13.698 kW/m2 and the air Reynolds number range 322-1982. Three different types of mini heat sinks were rectangle pin fins, cylindrical pin fins, and spiral pin fins with 36x28x9 mm and 5 mm fins high. There were 63 fins altogether and all were made of aluminum. The results showed that the characteristics of the temperature of heat sink of spiral pin fins was the least. Meanwhile the average heat transfer coefficient and Nusselt number of spiral pin fins were the most. Regarding the pressure drop, the rectangular pin fins was the least. The results of this study can be used to guide the design and development of electronic devices cooling system with forced convective heat transfer for higher performance in the future.

  1. Prediction of forced convective heat transfer and critical heat flux for subcooled water flowing in miniature tubes

    Science.gov (United States)

    Shibahara, Makoto; Fukuda, Katsuya; Liu, Qiusheng; Hata, Koichi

    2018-02-01

    The heat transfer characteristics of forced convection for subcooled water in small tubes were clarified using the commercial computational fluid dynamic (CFD) code, PHENICS ver. 2013. The analytical model consists of a platinum tube (the heated section) and a stainless tube (the non-heated section). Since the platinum tube was heated by direct current in the authors' previous experiments, a uniform heat flux with the exponential function was given as a boundary condition in the numerical simulation. Two inner diameters of the tubes were considered: 1.0 and 2.0 mm. The upward flow velocities ranged from 2 to 16 m/s and the inlet temperature ranged from 298 to 343 K. The numerical results showed that the difference between the surface temperature and the bulk temperature was in good agreement with the experimental data at each heat flux. The numerical model was extended to the liquid sublayer analysis for the CHF prediction and was evaluated by comparing its results with the experimental data. It was postulated that the CHF occurs when the fluid temperature near the heated wall exceeds the saturated temperature, based on Celata et al.'s superheated layer vapor replenishment (SLVR) model. The suggested prediction method was in good agreement with the experimental data and with other CHF data in literature within ±25%.

  2. Sensible Heat Flux Related to Variations in Atmospheric Turbulence Kinetic Energy on a Sandy Beach

    Science.gov (United States)

    2017-06-01

    FLUX RELATED TO VARIATIONS IN ATMOSPHERIC TURBULENCE KINETIC ENERGY ON A SANDY BEACH by Jessica S. Koscinski June 2017 Thesis Advisor...KINETIC ENERGY ON A SANDY BEACH 5. FUNDING NUMBERS 6. AUTHOR(S) Jessica S. Koscinski 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Naval...Sensible heat flux, turbulence kinetic energy , surf zone 15. NUMBER OF PAGES 57 16. PRICE CODE 17. SECURITY CLASSIFICATION OF REPORT

  3. Numerical investigation of Al2O3/water nanofluid laminar convective heat transfer through triangular ducts

    Directory of Open Access Journals (Sweden)

    Zeinali Heris Saeed

    2011-01-01

    Full Text Available Abstract In this article, laminar flow-forced convective heat transfer of Al2O3/water nanofluid in a triangular duct under constant wall temperature condition is investigated numerically. In this investigation, the effects of parameters, such as nanoparticles diameter, concentration, and Reynolds number on the enhancement of nanofluids heat transfer is studied. Besides, the comparison between nanofluid and pure fluid heat transfer is achieved in this article. Sometimes, because of pressure drop limitations, the need for non-circular ducts arises in many heat transfer applications. The low heat transfer rate of non-circular ducts is one the limitations of these systems, and utilization of nanofluid instead of pure fluid because of its potential to increase heat transfer of system can compensate this problem. In this article, for considering the presence of nanoparticl: es, the dispersion model is used. Numerical results represent an enhancement of heat transfer of fluid associated with changing to the suspension of nanometer-sized particles in the triangular duct. The results of the present model indicate that the nanofluid Nusselt number increases with increasing concentration of nanoparticles and decreasing diameter. Also, the enhancement of the fluid heat transfer becomes better at high Re in laminar flow with the addition of nanoparticles.

  4. Comparative measurements of natural convection heat transfer in channels by holographic interferometry and schlieren

    Energy Technology Data Exchange (ETDEWEB)

    Ambrosini, Dario [DIMEG, Universita dell' Aquila, Loc. Monteluco di Roio, I-67040 Roio Poggio (AQ) (Italy); Tanda, Giovanni [DIPTEM, Universita di Genova, Via all' Opera Pia 15a, I-67100 Genova (Italy)

    2006-01-01

    In this work, natural convection heat transfer in vertical channels is experimentally investigated by applying different optical techniques, namely holographic interferometry and schlieren. Both these techniques are based on the temperature dependence of the air refractive index but they detect different optical quantities and their use involves different instrumentation and optical components. Optical methods, non-intrusive in nature, are particularly suitable for the visualization of flow and thermal fields as witnessed by their increasing use in a range of scientific and engineering disciplines; for this reason, the introduction of these experimental tools into a laboratory course can be of high value. Physics and engineering students can get familiarized with optical techniques, grasp the basics of thermal phenomena, usually elusive, which can be more easily understood if they are made visible, and begin to master digital image analysis, a key skill in laboratory activities. A didactic description of holographic interferometry and schlieren is provided and experimental results obtained for vertical, smooth and rib-roughened channels with asymmetrical heating are presented. A comparison between distributions of the local heat transfer coefficient (or its dimensionless counterpart, the Nusselt number) revealed good agreement between the results separately obtained by the two techniques, thus proving their suitability for investigating free convection heat transfer in channels.

  5. New similarity solution of boundary layer flow along a continuously moving convectively heated horizontal plate by deductive group method

    Directory of Open Access Journals (Sweden)

    Uddin Mohammed Jashim

    2015-01-01

    Full Text Available A mathematical model is presented and analyzed for steady two-dimensional non-isothermal laminar free convective boundary layer flow along a convectively heated moving horizontal plate. New similarity transformations are developed using one parameter deductive group transformations and hence the governing transport equations are reduced to a system of coupled, nonlinear ordinary differential equations with associated boundary conditions. The reduced equations are then solved numerically by an implicit finite difference numerical method. The effects of pertinent parameters on the non-dimensional velocity, temperature, friction factor and heat transfer rates are investigated and presented graphically. It is found that friction factor decreases with the free convective parameter and rate of heat transfer increases with the convection-conduction parameter.

  6. Stagnation point heat transfer augmentation due to free stream turbulence

    Science.gov (United States)

    Gorla, R. S. R.

    1982-01-01

    A model has been proposed for the momentum eddy diffusivity induced by free stream turbulence intensity and integral length scale. The eddy diffusivity model is applied to the stagnation point of a cylinder situated in a uniform crossflow in the presence of free stream turbulence. A numerical solution of the governing momentum and energy equations with the proposed eddy diffusivity model yielded results for the skin friction coefficient and the Nusselt number. The numerical predictions of the present work are compared with experimental data and the agreement between the two is seen to be very good.

  7. Turbulence

    CERN Document Server

    Bailly, Christophe

    2015-01-01

    This book covers the major problems of turbulence and turbulent processes, including  physical phenomena, their modeling and their simulation. After a general introduction in Chapter 1 illustrating many aspects dealing with turbulent flows, averaged equations and kinetic energy budgets are provided in Chapter 2. The concept of turbulent viscosity as a closure of the Reynolds stress is also introduced. Wall-bounded flows are presented in Chapter 3, and aspects specific to boundary layers and channel or pipe flows are also pointed out. Free shear flows, namely free jets and wakes, are considered in Chapter 4. Chapter 5 deals with vortex dynamics. Homogeneous turbulence, isotropy, and dynamics of isotropic turbulence are presented in Chapters 6 and 7. Turbulence is then described both in the physical space and in the wave number space. Time dependent numerical simulations are presented in Chapter 8, where an introduction to large eddy simulation is offered. The last three chapters of the book summarize remarka...

  8. Influence of high range of mass transfer coefficient and convection heat transfer on direct contact membrane distillation performance

    KAUST Repository

    Lee, Jung Gil

    2017-11-03

    In order to improve water production of membrane distillation (MD), the development of high performance membrane having better mass transfer and enhancement of convection heat transfer in MD module have been continuously investigated. This paper presents the relationship between the heat and mass transfer resistance across the membrane and the performance improvement. Various ranges of mass transfer coefficient (MTC) from normal (0.3×10−6 to 2.1×10−6kg/m2sPa: currently available membranes) to high (>2.1×10−6kg/m2sPa: membranes under development) were simulated using an experimentally validated model at different ranges of convection heat transfer by varying the inlet flow rates and spacer enhancement factor. The effect of mass transfer and convection heat transfer on the MD performance parameters including temperature polarization coefficient (TPC), mean permeate flux, and specific energy consumption were investigated in a direct contact MD (DCMD) configuration. Results showed that improving the MTC at the low ranges is more important than that at the high ranges where the heat transfer resistance becomes dominant and hence the convection heat transfer coefficient must be increased. Therefore, an effort on designing MD modules using feed and permeate spacers and controlling the membrane surface roughness to increase the convection heat transfer and TPC in the channel aiming to enhance the flux is required because the currently developed mass transfer has almost reached the critical point.

  9. MHD Modeling of the Solar Wind with Turbulence Transport and Heating

    Science.gov (United States)

    Goldstein, M. L.; Usmanov, A. V.; Matthaeus, W. H.; Breech, B.

    2009-01-01

    We have developed a magnetohydrodynamic model that describes the global axisymmetric steady-state structure of the solar wind near solar minimum with account for transport of small-scale turbulence associated heating. The Reynolds-averaged mass, momentum, induction, and energy equations for the large-scale solar wind flow are solved simultaneously with the turbulence transport equations in the region from 0.3 to 100 AU. The large-scale equations include subgrid-scale terms due to turbulence and the turbulence (small-scale) equations describe the effects of transport and (phenomenologically) dissipation of the MHD turbulence based on a few statistical parameters (turbulence energy, normalized cross-helicity, and correlation scale). The coupled set of equations is integrated numerically for a source dipole field on the Sun by a time-relaxation method in the corotating frame of reference. We present results on the plasma, magnetic field, and turbulence distributions throughout the heliosphere and on the role of the turbulence in the large-scale structure and temperature distribution in the solar wind.

  10. Convective air warming is more effective than resistive heating in an experimental model with a water dummy.

    Science.gov (United States)

    Ittner, Karl Peter; Bachfischer, Markus; Zimmermann, Markus; Taeger, Kai

    2004-06-01

    Trauma patients with accidental hypothermia have adverse outcomes when compared with normothermic patients. Studies with a small number of mild hypothermic volunteers suggested that convective warming is more effective than warming with 12 volt resistive heating blankets. In a laboratory study, we compared the warming effectiveness of two electric blankets and convective air warming. The average speed of convective rewarming during anaesthesia in patients is approximately 0.6 degree C per hour. Accordingly, calibration of the dummy was performed with increasing amounts of water during convective warming until we reached a temperature gain of 0.6 degree C per hour. The following warming experiments were performed: 12 volt electric warming blanket (SH6012, Hella); 12 volt electric warming blanket (Thermamed, whole-body blanket); convective air warming (Warm Touch, Mallinckrodt, whole-body blanket). Each experiment was repeated four times. The temperature development was measured and recorded online. Convective warming increased the dummy temperature 0.6 degree C per hour, Thermamed 0.3 degree C per hour (Pwarming) and two Hella blankets 0.2 degree C per hour (Pwarming). Our laboratory investigation confirmed the superiority of convective warming over resistive heating. Efforts should be made to incorporate convective warming into the out-of-hospital treatment of trauma patients.

  11. Mixed convection heat and mass transfer in peristaltic flow with chemical reaction and inclined magnetic field

    Science.gov (United States)

    Noreen, S.; Hayat, T.; Alsaedi, A.; Qasim, M.

    2013-09-01

    A mathematical model is constructed to investigate the mixed convective heat and mass transfer effects on peristaltic flow of magnetohydrodynamic pseudoplastic fluid in a symmetric channel. An analysis has been carried out to examine the impact of an inclined magnetic field and chemical reaction in presence of heat sink/source. Mechanics of flow and heat/mass transfer described in terms of continuity, linear momentum, energy and concentration equations are predicted by using long wavelength and low Reynolds number. Expressions for stream function, temperature, concentration and pressure gradient are derived. Numerical simulation is performed for the rise in pressure per wave length. Effects of several physical parameters on the flow quantities are analyzed.

  12. Computational Modelling of Couette Flow of Nanofluids with Viscous Heating and Convective Cooling

    Directory of Open Access Journals (Sweden)

    Oluwole Daniel Makinde

    2014-01-01

    Full Text Available The combined effect of viscous heating and convective cooling on Couette flow and heat transfer characteristics of water base nanofluids containing Copper Oxide (CuO and Alumina (Al2O3 as nanoparticles is investigated. It is assumed that the nanofluid flows in a channel between two parallel plates with the channel’s upper plate accelerating and exchange heat with the ambient surrounding following the Newton’s law of cooling, while the lower plate is stationary and maintained at a constant temperature. Using appropriate similarity transformation, the governing Navier-Stokes and the energy equations are reduced to a set of nonlinear ordinary differential equations. These equations are solved analytically by regular perturbation method with series improvement technique and numerically by an efficient Runge-Kutta-Fehlberg integration technique coupled with shooting method. The effects of the governing parameters on the dimensionless velocity, temperature, skin friction, pressure drop and Nusselt number are presented graphically, and discussed quantitatively.

  13. Progress towards understanding and predicting convection heat transfer in the turbine gas path

    Science.gov (United States)

    Simoneau, Robert J.; Simon, Frederick F.

    1992-01-01

    A new era is drawing in the ability to predict convection heat transfer in the turbine gas path. We feel that the technical community now has the capability to mount a major assault on this problem, which has eluded significant progress for a long time. We hope to make a case for this bold statement by reviewing the state of the art in three major heat transfer, configuration-specific experiments, whose data have provided the big picture and guided both the fundamental modeling research and the code development. Following that, we review progress and directions in the development of computer codes to predict turbine gas path heat transfer. Finally, we cite examples and make observations on the more recent efforts to do all this work in a simultaneous, interactive, and more synergistic manner. We conclude with an assessment of progress, suggestions for how to use the current state of the art, and recommendations for the future.

  14. Hydromagnetic Stagnation-Point Flow towards a Radially Stretching Convectively Heated Disk

    Directory of Open Access Journals (Sweden)

    S. Shateyi

    2013-01-01

    Full Text Available The steady stagnation-point flow and heat transfer of an electrically conducted incompressible viscous fluid are extended to the case where the disk surface is convectively heated and radially stretching. The fluid is subjected to an external uniform magnetic field perpendicular to the plane of the disk. The governing momentum and energy balance equations give rise to nonlinear boundary value problem. Using a spectral relaxation method with a Chebyshev spectral collocation method, the numerical solutions are obtained over the entire range of the physical parameters. Emphasis has been laid to study the effects of viscous dissipation and Joule heating on the thermal boundary layer. Pertinent results on the effects of various thermophysical parameters on the velocity and temperature fields as well as local skin friction and local Nusselt number are discussed in detail and shown graphically and/or in tabular form.

  15. Evaluation of heat transfer in acupuncture needles: convection and conduction approaches.

    Science.gov (United States)

    Tzou, Chieh-Han John; Yang, Tzyy-Yih; Chung, Ya-Chien

    2015-04-01

    Originating in ancient China, acupuncture using needles has been developed for thousands of years and has received attention for its reported medical remedies, such as pain relief and chronic disease treatment. Heat transfer through the needles, which might have effects on the biomechanism of acupuncture, providing a stimulus and regulating homeostasis, has never been studied. This article analyzes the significance of heat transfer through needles via convection and conduction, approached by means of computational analysis. The needle is a cylindrical body, and an axis symmetrical steady-state heat-transfer model that viscosity and static pressure was not applied. This article evaluates heat transfer via acupuncture needles by using five metal materials: silver, copper, brass, iron, and stainless steel. A silver needle of the type extensively applied in acupuncture can dissipate more than seven times as much heat as a stainless steel needle of the same type. Heat transfer through such a needle is significant, compared to natural body-energy consumption over a range of ambient temperatures. The mechanism by which heat flows in or out of the body through the needles may be crucial in the remedial efficacy of acupuncture. Copyright © 2015. Published by Elsevier B.V.

  16. Effect of internal heat generation or absorption on MHD free convection from an isothermal truncated cone

    Directory of Open Access Journals (Sweden)

    A.H. Srinivasa

    2016-06-01

    Full Text Available This paper examines the effect of heat generation or absorption on the free convection flow of an incompressible, electrically conducting fluid about an isothermal truncated cone in the presence of a transverse magnetic field. The non-linear coupled partial differential equations governing the flow and heat transfer have been solved numerically, using an efficient implicit finite-difference scheme along with quasilinearization technique. The nonsimilar solutions have been obtained for the problem overcoming numerical difficulties near the leading edge and in the downstream regime, for air (Pr = 0.72. The effects of various physical parameters on skin friction and heat transfer coefficients and, on velocity and temperature are shown graphically for different values of magnetic parameter (M and heat generation/absorption parameter (Q. It is observed that, magnetic field decreases both skin friction and heat transfer coefficients. The effect of heat generation or absorption is found to be very significant on heat transfer, but its effect on skin friction is negligible.

  17. Natural convection heat transfer characteristics of the molten metal pool with solidification by boiling coolant

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Jae Seon; Suh, Kune Yull; Chung, Chang Hyun [Seoul National University, Seoul (Korea, Republic of); Paark, Rae Joon; Kim, Sang Baik [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1997-12-31

    This paper presents results of experimental studies on the heat transfer and solidification of the molten metal pool with overlying coolant with boiling. The metal pool is heated from the bottom surface and coolant is injected onto the molten metal pool. Ad a result, the crust, which is a solidified layer, may form at the top of the molten metal pool. Heat transfer is accomplished by a conjugate mechanism, which consists of the natural convection of the molten metal pool, the conduction in the crust layer and the convective boiling heat transfer in the coolant. This work examines the crust formation and the heat transfer rate on the molten metal pool with boiling coolant. The simulant molten pool material is tin (Sn) with the melting temperature of 232 deg C. Demineralized water is used as the working coolant. The crust layer thickness was ostensibly varied by the heated bottom surface temperature of the test section, but not much affected by the coolant injection rate. The correlation between the Nusselt number and the Rayleigh number in the molten metal pool region of this study is compared against the crust formation experiment without coolant boiling and the literature correlations. The present experimental results are higher than those from the experiment without coolant boiling, but show general agreement with the Eckert correlation, with some deviations in the high and low ends of the Rayleigh number. This discrepancy is currently attributed to concurrent rapid boiling of the coolant on top of the metal layer. 10 refs., 4 figs., 1 tab. (Author)

  18. Natural convection in a water tank with a heated horizontal plate facing downward

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Sun Kyoo; Jung, Moon Kee [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of); Helmut Hoffmann [Kemforschungszentrum Karlsruhe/IATF, (Germany)

    1995-06-01

    Experimental and computational studies were carried out to investigate the natural convection of the single phase flow in a tank with a heated horizontal plate facing downward. This is a simplified model for investigations of the influence of a core melt at the bottom of a reactor vessel on the thermal hydraulic behavior in a water filled cavity surrounding the vessel. In this case the vessel is simulated by a hexahedron insulated box with a heated plate horizontally mounted at the bottom of the box. The box with the heated plate is installed in a water filled hexahedron tank. Coolers are immersed in the U-type water volume between the box and the tank. Although the multicomponent flows exist more probably below the heated plate in reality, present study concentrates on the single phase flow in a first step prior to investigating the complicated multicomponent thermal hydraulic phenomena. In the present study, in order to get a better understanding for the natural convection characteristics below the heated plate, the velocity and temperature are measured by LDA(Laser Doppler Anemometry) and thermocouples, respectively. And flow fields are visualized by taking pictures of the flow region with suspended particles. The results show the occurrence of a very effective circulation of the fluid in the whole flow area as the heater and coolers are put into operation. In the remote region below the heated plate the flow is nearly stagnant, and a remarkable temperature stratification can be observed with very thin thermal boundary. Analytical predictions using the FLUTAN code show a reasonable matching of the measured velocity fields. 18 figs., 2 tabs., 18 refs. (Author).

  19. Large eddy simulation of rotating turbulent flows and heat transfer by the lattice Boltzmann method

    Science.gov (United States)

    Liou, Tong-Miin; Wang, Chun-Sheng

    2018-01-01

    Due to its advantage in parallel efficiency and wall treatment over conventional Navier-Stokes equation-based methods, the lattice Boltzmann method (LBM) has emerged as an efficient tool in simulating turbulent heat and fluid flows. To properly simulate the rotating turbulent flow and heat transfer, which plays a pivotal role in tremendous engineering devices such as gas turbines, wind turbines, centrifugal compressors, and rotary machines, the lattice Boltzmann equations must be reformulated in a rotating coordinate. In this study, a single-rotating reference frame (SRF) formulation of the Boltzmann equations is newly proposed combined with a subgrid scale model for the large eddy simulation of rotating turbulent flows and heat transfer. The subgrid scale closure is modeled by a shear-improved Smagorinsky model. Since the strain rates are also locally determined by the non-equilibrium part of the distribution function, the calculation process is entirely local. The pressure-driven turbulent channel flow with spanwise rotation and heat transfer is used for validating the approach. The Reynolds number characterized by the friction velocity and channel half height is fixed at 194, whereas the rotation number in terms of the friction velocity and channel height ranges from 0 to 3.0. A working fluid of air is chosen, which corresponds to a Prandtl number of 0.71. Calculated results are demonstrated in terms of mean velocity, Reynolds stress, root mean square (RMS) velocity fluctuations, mean temperature, RMS temperature fluctuations, and turbulent heat flux. Good agreement is found between the present LBM predictions and previous direct numerical simulation data obtained by solving the conventional Navier-Stokes equations, which confirms the capability of the proposed SRF LBM and subgrid scale relaxation time formulation for the computation of rotating turbulent flows and heat transfer.

  20. The Structure of Plasma Heating in Gyrokinetic Alfv\\'enic Turbulence

    CERN Document Server

    Navarro, A B; Told, D; Groselj, D; Crandall, P; Jenko, F

    2016-01-01

    We analyze plasma heating in weakly collisional kinetic Alfv\\'en wave (KAW) turbulence using high resolution gyrokinetic simulations spanning the range of scales between the ion and the electron gyroradii. Real space structures that have a higher than average heating rate are shown not to be confined to current sheets. This novel result is at odds with previous studies, which use the electromagnetic work in the local electron fluid frame, i.e. $\\mathbf{J} \\!\\cdot\\! (\\mathbf{E} + \\mathbf{v}_e\\times\\mathbf{B})$, as a proxy for turbulent dissipation to argue that heating follows the intermittent spatial structure of the electric current. Furthermore, we show that electrons are dominated by parallel heating while the ions prefer the perpendicular heating route. We comment on the implications of the results presented here.

  1. Enhancing Oxidative Stability of Sunflower Oil during Convective and Microwave Heating Using Grape Seed Extract

    Directory of Open Access Journals (Sweden)

    Mariana-Atena Poiana

    2012-07-01

    Full Text Available This study was performed to investigate the effectiveness of grape seed extract (GSE compared to butylated hydroxytoluene (BHT on retarding lipid oxidation of sunflower oil subjected to convection and microwave heating up to 240 min under simulated frying conditions. The progress of lipid oxidation was assessed in terms of peroxide value (PV, p-anisidine value (p-AV, conjugated dienes and trienes (CD, CT, inhibition of oil oxidation (IO and TOTOX value. In addition, total phenolic content (TP was evaluated in samples before and after heating in order to assess the changes in these compounds relative to the extent of lipid oxidation. The results of this study highlight that GSE showed a significantly inhibitory effect on lipid oxidation during both treatments, although to a different extent. This ability was dose-dependent; therefore, the extent of lipid oxidation was inversely related to GSE level. Convective heating, respective microwave exposure for 240 min of samples supplemented by GSE to a level of 1000 ppm, resulted in significant decreases of investigated indices relative to the control values as follows: PV (48%; 30%, p-AV (29%; 40%, CD (45%; 30%, CT (41%; 36%, TOTOX (35%; 37%. GSE to a level of 600–800 ppm inhibited the lipid oxidation in a similar manner to BHT. These results suggested that GSE can be used as a potential natural extract for improving oxidative stability of sunflower oil during thermal applications.

  2. Enhancing oxidative stability of sunflower oil during convective and microwave heating using grape seed extract.

    Science.gov (United States)

    Poiana, Mariana-Atena

    2012-01-01

    This study was performed to investigate the effectiveness of grape seed extract (GSE) compared to butylated hydroxytoluene (BHT) on retarding lipid oxidation of sunflower oil subjected to convection and microwave heating up to 240 min under simulated frying conditions. The progress of lipid oxidation was assessed in terms of peroxide value (PV), p-anisidine value (p-AV), conjugated dienes and trienes (CD, CT), inhibition of oil oxidation (IO) and TOTOX value. In addition, total phenolic content (TP) was evaluated in samples before and after heating in order to assess the changes in these compounds relative to the extent of lipid oxidation. The results of this study highlight that GSE showed a significantly inhibitory effect on lipid oxidation during both treatments, although to a different extent. This ability was dose-dependent; therefore, the extent of lipid oxidation was inversely related to GSE level. Convective heating, respective microwave exposure for 240 min of samples supplemented by GSE to a level of 1000 ppm, resulted in significant decreases of investigated indices relative to the control values as follows: PV (48%; 30%), p-AV (29%; 40%), CD (45%; 30%), CT (41%; 36%), TOTOX (35%; 37%). GSE to a level of 600-800 ppm inhibited the lipid oxidation in a similar manner to BHT. These results suggested that GSE can be used as a potential natural extract for improving oxidative stability of sunflower oil during thermal applications.

  3. Enhancing Oxidative Stability of Sunflower Oil during Convective and Microwave Heating Using Grape Seed Extract

    Science.gov (United States)

    Poiana, Mariana-Atena

    2012-01-01

    This study was performed to investigate the effectiveness of grape seed extract (GSE) compared to butylated hydroxytoluene (BHT) on retarding lipid oxidation of sunflower oil subjected to convection and microwave heating up to 240 min under simulated frying conditions. The progress of lipid oxidation was assessed in terms of peroxide value (PV), p-anisidine value (p-AV), conjugated dienes and trienes (CD, CT), inhibition of oil oxidation (IO) and TOTOX value. In addition, total phenolic content (TP) was evaluated in samples before and after heating in order to assess the changes in these compounds relative to the extent of lipid oxidation. The results of this study highlight that GSE showed a significantly inhibitory effect on lipid oxidation during both treatments, although to a different extent. This ability was dose-dependent; therefore, the extent of lipid oxidation was inversely related to GSE level. Convective heating, respective microwave exposure for 240 min of samples supplemented by GSE to a level of 1000 ppm, resulted in significant decreases of investigated indices relative to the control values as follows: PV (48%; 30%), p-AV (29%; 40%), CD (45%; 30%), CT (41%; 36%), TOTOX (35%; 37%). GSE to a level of 600–800 ppm inhibited the lipid oxidation in a similar manner to BHT. These results suggested that GSE can be used as a potential natural extract for improving oxidative stability of sunflower oil during thermal applications. PMID:22942764

  4. Fully determined scaling laws for volumetrically heated convective systems, a tool for assessing habitability of exoplanets

    Science.gov (United States)

    Vilella, Kenny; Kaminski, Edouard

    2017-05-01

    The long-term habitability of a planet rises from its ability to generate and maintain an atmosphere through partial melting and volcanism. This question has been mainly addressed in the framework of plate tectonics, which may be too specific to apply to the wide range of internal dynamics expected for exoplanets, and even to the thermal evolution of the early Earth. Here we propose a more general theoretical approach of convection to build a regime diagram giving the conditions for partial melting to occur, in planetary bodies, as a function of key parameters that can be estimated for exoplanets, their size and internal heating rate. To that aim, we introduce a refined view of the Thermal Boundary Layer (TBL) in a convective system heated from within, that focuses on the temperature and thickness of the TBL at the top of the hottest temperature profiles, along which partial melting shall first occur. This ;Hottest Thermal Boundary Layer; (HotTBL) is first characterized using fully theoretical scaling laws based on the dynamics of thermal boundary layers. These laws are the first ones proposed in the literature that do not rely on empirical determinations of dimensionless constants and that apply to both low Rayleigh and high Rayleigh convective regimes. We show that the scaling laws can be successfully applied to planetary bodies by comparing their predictions to full numerical simulations of the Moon. We then use the scaling laws to build a regime diagram for exoplanets. Combined with estimates of internal heating in exoplanets, the regime diagram predicts that in the habitable zone partial melting occurs in planets younger than the Earth.

  5. Thermal radiation effect on a mixed convection flow and heat transfer of the Williamson fluid past an exponentially shrinking permeable sheet with a convective boundary condition

    Science.gov (United States)

    Zaib, A.; Bhattacharyya, K.; Khalid, M.; Shafie, S.

    2017-05-01

    The thermal radiation effect on a steady mixed convective flow with heat transfer of a nonlinear (non-Newtonian) Williamson fluid past an exponentially shrinking porous sheet with a convective boundary condition is investigated numerically. In this study, both an assisting flow and an opposing flow are considered. The governing equations are converted into nonlinear ordinary differential equations by using a suitable transformation. A numerical solution of the problem is obtained by using the Matlab software package for different values of the governing parameters. The results show that dual nonsimilar solutions exist for the opposing flow, whereas the solution for the assisting flow is unique. It is also observed that the dual nonsimilar solutions exist only if a certain amount of mass suction is applied through the porous sheet, which depends on the Williamson parameter, convective parameter, and radiation parameter.

  6. The conditions of similarity and generalized dependences for calculating convective heat transfer in supercritical pressure coolants

    Science.gov (United States)

    Deev, V. I.; Kharitonov, V. S.; Churkin, A. N.; Baisov, A. M.

    2017-11-01

    In this report the assessment of the results of recent experimental investigations of heat transfer in turbulent flow of supercritical water and modeling fluids (carbon dioxide, Freon) in vertical channels of different geometry (tubes, annular gaps and rod bundles) is presented. The conditions of similarity and the system of criteria, which determine the intensity of heat exchange in the fluids near the critical point, are considered. Due to the small hydraulic diameter of the heat exchange channels in the core of nuclear reactors it is possible to neglect the gravitational forces compared to the acceleration caused by the thermal inertia effects and the forces of viscosity. Based on these ideas two comprehensive criteria were proposed. Their application in the basic equation of heat transfer suggested by the authors earlier for the normal regimes satisfactorily (with an error of 20–25%) describes the features of change of heat transfer coefficient in the deteriorated and mixed regimes of heat transfer. The system of equations suitable for engineering calculation of heat transfer in channels of nuclear reactors cooled with supercritical pressure water was developed.

  7. Heat Transfer and Mass Diffusion in Nanofluids over a Moving Permeable Convective Surface

    Directory of Open Access Journals (Sweden)

    Muhammad Qasim

    2013-01-01

    Full Text Available Heat transfer and mass diffusion in nanofluid over a permeable moving surface are investigated. The surface exhibits convective boundary conditions and constant mass diffusion. Effects of Brownian motion and thermophoresis are considered. The resulting partial differential equations are reduced into coupled nonlinear ordinary differential equations using suitable transformations. Shooting technique is implemented for the numerical solution. Velocity, temperature, and concentration profiles are analyzed for different key parameters entering into the problem. Performed comparative study shows an excellent agreement with the previous analysis.

  8. Assessment of thermal conductivity, viscosity and specific heat of nanofluids in single phase laminar indernal forced convection

    NARCIS (Netherlands)

    Vanapalli, Srinivas; ter Brake, Hermanus J.M.

    2013-01-01

    Nanofluids are considered for improving the heat exchange in forced convective flow. In literature, the benefit of nanofluids compared to the corresponding base fluid is represented by several figures-of-merit in which the heat transfer benefit and the cost of pumping the fluid are considered. These

  9. Natural Convection Flow along an Isothermal Vertical Flat Plate with Temperature Dependent Viscosity and Heat Generation

    Directory of Open Access Journals (Sweden)

    Md. Mamun Molla

    2014-01-01

    Full Text Available The purpose of this study is to investigate the natural convection laminar flow along an isothermal vertical flat plate immersed in a fluid with viscosity which is the exponential function of fluid temperature in presence of internal heat generation. The governing boundary layer equations are transformed into a nondimensional form and the resulting nonlinear system of partial differential equations is reduced to a convenient form which are solved numerically using an efficient marching order implicit finite difference method with double sweep technique. Numerical results are presented in terms of the velocity and temperature distribution of the fluid as well as the heat transfer characteristics, namely, the wall shear stress and the local and average rate of heat transfer in terms of the local skin-friction coefficient, the local and average Nusselt number for a wide range of the viscosity-variation parameter, heat generation parameter, and the Rayleigh number. Increasing viscosity variation parameter and Rayleigh number lead to increasing the local and average Nusselt number and decreasing the wall shear stress. Wall shear stress and the rate of heat transfer decreased due to the increase of heat generation.

  10. Turbulence structure in a diabatically heated forest canopy composed of fractal Pythagoras trees

    Science.gov (United States)

    Schröttle, Josef; Dörnbrack, Andreas

    2013-06-01

    We investigate the turbulent flow through a heterogeneous forest canopy by high-resolution numerical modeling. For this purpose, a novel approach to model individual trees is implemented in our large-eddy simulation (LES). A group of sixteen fractal Pythagoras trees is placed in the computational domain and the tree elements are numerically treated as immersed boundaries. Our objective is to resolve the multiscale flow response starting at the diameter of individual tree elements up to the depth of the atmospheric surface layer. A reference run, conducted for the forest flow under neutral thermal stratification, produces physically meaningful turbulence statistics. Our numerical results agree quantitatively with data obtained from former field-scale LESs and wind tunnel experiments. Furthermore, the numerical simulations resolve vortex shedding behind individual branches and trunks as well as the integral response of the turbulent flow through the heterogeneous forest canopy. A focus is the investigation of the turbulence structure of the flow under stable thermal stratification and in response to the heating of the fractal tree crowns. For the stratified flows, statistical quantities, e.g. turbulent kinetic energy and vorticity, are presented and the turbulent exchange processes of momentum and heat are considered in detail. The onset and formation of coherent structures such as elevated shear layers above the diabatically heated forest canopy are analyzed. For the stably stratified flow, temperature ramps above the forest canopy were simulated in agreement with previous observations. Thermally driven vortices with a typical diameter of the canopy height were simulated when the tree crowns were diabatically heated. The impact of the coherent flow structures on the heat flux is investigated.

  11. Convective Heat Transfer Scaling of Ignition Delay and Burning Rate with Heat Flux and Stretch Rate in the Equivalent Low Stretch Apparatus

    Science.gov (United States)

    Olson, Sandra

    2011-01-01

    To better evaluate the buoyant contributions to the convective cooling (or heating) inherent in normal-gravity material flammability test methods, we derive a convective heat transfer correlation that can be used to account for the forced convective stretch effects on the net radiant heat flux for both ignition delay time and burning rate. The Equivalent Low Stretch Apparatus (ELSA) uses an inverted cone heater to minimize buoyant effects while at the same time providing a forced stagnation flow on the sample, which ignites and burns as a ceiling fire. Ignition delay and burning rate data is correlated with incident heat flux and convective heat transfer and compared to results from other test methods and fuel geometries using similarity to determine the equivalent stretch rates and thus convective cooling (or heating) rates for those geometries. With this correlation methodology, buoyant effects inherent in normal gravity material flammability test methods can be estimated, to better apply the test results to low stretch environments relevant to spacecraft material selection.

  12. Scaling laws of turbulence and heating of fast solar wind: the role of density fluctuations.

    Science.gov (United States)

    Carbone, V; Marino, R; Sorriso-Valvo, L; Noullez, A; Bruno, R

    2009-08-07

    Incompressible and isotropic magnetohydrodynamic turbulence in plasmas can be described by an exact relation for the energy flux through the scales. This Yaglom-like scaling law has been recently observed in the solar wind above the solar poles observed by the Ulysses spacecraft, where the turbulence is in an Alfvénic state. An analogous phenomenological scaling law, suitably modified to take into account compressible fluctuations, is observed more frequently in the same data set. Large-scale density fluctuations, despite their low amplitude, thus play a crucial role in the basic scaling properties of turbulence. The turbulent cascade rate in the compressive case can, moreover, supply the energy dissipation needed to account for the local heating of the nonadiabatic solar wind.

  13. Evaporation of bi-component droplets in a heated, highly turbulent flow

    Energy Technology Data Exchange (ETDEWEB)

    Moreau, F.; Bazile, R. [Universite de Toulouse, INPT, UPS, IMFT, Institut de Mecanique des Fluides de Toulouse, Toulouse (France); CNRS, IMFT, Toulouse (France)

    2012-08-15

    This work aims to understand the phenomena that occur in a combustion chamber where multi-component fuel droplets are injected. Many evaporation models exist but the influence of turbulence on spray vaporization is not yet well understood. This study gives a useful database to improve these models. The objective of the work is to measure the dispersion and the evaporation of bi-component (octane/3-pentanone) droplets and the resulting vapor mixing in a well-known, heated, highly turbulent channel flow. The carrier flow shows high turbulence levels, flat profiles for the mean velocity and the velocity fluctuations. The injected droplets have a large variety of behaviors due to the large polydispersion and to the turbulence. The evolution of 3-pentanone liquid concentration, mass flux, and droplet clusters are described. Mean concentration, fluctuations of concentration, and mixing of the vapor phase are characterized. (orig.)

  14. MAGNETOHYDRODYNAMIC WAVES AND CORONAL HEATING: UNIFYING EMPIRICAL AND MHD TURBULENCE MODELS

    Energy Technology Data Exchange (ETDEWEB)

    Sokolov, Igor V.; Van der Holst, Bart; Oran, Rona; Jin, Meng; Manchester, Ward B. IV; Gombosi, Tamas I. [Department of AOSS, University of Michigan, 2455 Hayward Street, Ann Arbor, MI 48109 (United States); Downs, Cooper [Predictive Science Inc., 9990 Mesa Rim Road, Suite 170, San Diego, CA 92121 (United States); Roussev, Ilia I. [Institute for Astronomy, University of Hawaii, 2680 Woodlawn Drive, Honolulu, HI 96822 (United States); Evans, Rebekah M., E-mail: igorsok@umich.edu [NASA Goddard Space Flight Center, Space Weather Lab, 8800 Greenbelt Road, Greenbelt, MD 20771 (United States)

    2013-02-10

    We present a new global model of the solar corona, including the low corona, the transition region, and the top of the chromosphere. The realistic three-dimensional magnetic field is simulated using the data from the photospheric magnetic field measurements. The distinctive feature of the new model is incorporating MHD Alfven wave turbulence. We assume this turbulence and its nonlinear dissipation to be the only momentum and energy source for heating the coronal plasma and driving the solar wind. The difference between the turbulence dissipation efficiency in coronal holes and that in closed field regions is because the nonlinear cascade rate degrades in strongly anisotropic (imbalanced) turbulence in coronal holes (no inward propagating wave), thus resulting in colder coronal holes, from which the fast solar wind originates. The detailed presentation of the theoretical model is illustrated with the synthetic images for multi-wavelength EUV emission compared with the observations from SDO AIA and STEREO EUVI instruments for the Carrington rotation 2107.

  15. Scaling Laws of Turbulence and Heating of Fast SolarWind: The Role of Density Fluctuations

    CERN Document Server

    Carbone, V; Sorriso-Valvo, L; Noullez, A; Bruno, R

    2010-01-01

    Incompressible and isotropic magnetohydrodynamic turbulence in plasms can be described by an exact relation for the energy flux through the scales. This Yaglom-like scaling law has been recently observed in the solar wind above the solar poles observed by the Ulysses spacecraft, where the turbulence is in an Alfv\\'enic state. An analogous phenomenological scaling law, suitably modified to take into account compressible fluctuations, is observed more frequently in the same dataset. Large scale density fluctuations, despite their low amplitude, play thus a crucial role in the basic scaling properties of turbulence. The turbulent cascade rate in the compressive case can moreover supply the energy dissipation needed to account for the local heating of the non-adiabatic solar wind.

  16. Thermal Convection in a Fluid Layer Heated From Below and From Within - Implication for Planetary Evolution

    Science.gov (United States)

    Choblet, G.; Parmentier, M.; Sotin, C.

    2002-12-01

    Solid-state thermal convection in terrestrial planets interiors is generated by both volumetric heating (radiogenic elements, secular cooling) and heating from below (cooling of the metallic core). However, the relative importance of plumes emanating from both boundary layers and their interaction is still poorly understood. The aim of the present study is to propose a precise scaling for heat transfer in this heating configuration. Our initial numerical experiments have examined an isoviscous fluid in a Cartesian geometry (both 2D and 3D), since this allows well resolved results to be obtained with modest-scale computation. A relationship assuming that the top and bottom boundary layers are of equal thickness so that the ratio of temperature differences across them varies in a simple way with the fraction of heating from below produces a correct first order scaling. This leads to the prediction that the temperature of the well mixed interior does not vary with the fraction of heat supplied from below. However, in our numerical experiments, horizontally averaged temperature within the well mixed interior for a given amount of heat sources (basal plus internal) varies with the way heat is distributed between the bottom surface and the interior of the layer by an amount that can be significant on scales of interest for planetary evolution. In addition, systematic differences are observed between 2D and 3D numerical experiments ; other variations appear according on the basal heating mode (either flux or temperature can be prescribed). This reflects the dynamics of the interaction of plumes with thermal boundary layers and with each other. We thus propose a more complete scaling based on the influence of a plume on both the boundary layer where it forms and the opposite boundary layer where it produces a stagnation point. This leads to a scaling which predicts that the two boundary layers are of different thickness and allows a more accurate description of temperature

  17. Effects of spatial gradients in thermophysical properties on the topology of turbulence in heated channel flow of supercritical fluids

    Science.gov (United States)

    Azih, Chukwudi; Yaras, Metin I.

    2018-01-01

    The current literature suggests that large spatial gradients of thermophysical properties, which occur in the vicinity of the pseudo-critical thermodynamic state, may result in significant variations in forced-convection heat transfer rates. Specifically, these property gradients induce inertia- and buoyancy-driven phenomena that may enhance or deteriorate the turbulence-dominated heat convection process. Through direct numerical simulations, the present study investigates the role of coherent flow structures in channel geometries for non-buoyant and buoyant flows of supercritical water, with buoyant configurations involving wall-normal oriented gravitational acceleration and downstream-oriented gravitational acceleration. This sequence of simulations enables the evaluation of the relative contributions of inertial and buoyancy phenomena to heat transfer variations. In these simulations, the state of the working fluid is in the vicinity of the pseudo-critical point. The uniform wall heat flux and the channel mass flux are specified such that the heat to mass flux ratio is 3 kJ/kg, with an inflow Reynolds number of 12 000 based on the channel hydraulic diameter, the area-averaged inflow velocity, and fluid properties evaluated at the bulk temperature and pressure of the inflow plane. In the absence of buoyancy forces, notable reductions in the density and viscosity in close proximity of the heated wall are observed to promote generation of small-scale vortices, with resultant breakdown into smaller scales as they interact with preexisting larger near-wall vortices. This interaction results in a reduction in the overall thermal mixing at particular wall-normal regions of the channel. Under the influence of wall-normal gravitational acceleration, the wall-normal density gradients are noted to enhance ejection motions due to baroclinic vorticity generation on the lower wall, thus providing additional wall-normal thermal mixing. Along the upper wall, the same mechanism

  18. New Generation Meteorological Satellite Imager Aviation Decision Support Applications for Detection of Convection, Turbulence, and Volcanic Ash

    Science.gov (United States)

    Feltz, Wayne

    2016-04-01

    A suite of aviation related decision support products have been in development to meet GOES-R science requirements since 2008 and are being evaluated to assess meteorological hazards to aircraft in flight derived from the current generation of European Spinning Enhanced Visible and Infrared Imager (SEVIRI) imager data. This presentation will focus on GOES-R Advanced Baseline Imager (ABI) measurement requirements relating to satellite-based aviation convective, turbulence, and volcanic ash/SO2 products that can be applied globally on next generation geostationary imagers including the Japanese Himawari, South Korean COMS (AMI), and European Metop-SG imagers. These new methodologies have relevance on current generation GOES and SEVIRI imagers, and overview will include discussion on how product utility has been improved through satellite GOES-R/JPSS Proving Ground NOAA testbed activities. Satellite-based decision support for aviation context toward improvement of future air transportation route planning and warning for the general public with emphasis on successfully bridging research to operations will also be discussed with anticipated October 2016 launch of GOES-R.

  19. Low-dimensional model of turbulent Rayleigh-Benard convection in a Cartesian cell with square domain

    CERN Document Server

    Bailon-Cuba, Jorge

    2011-01-01

    A low-dimensional model (LDM) for turbulent Rayleigh-Benard convection in a Cartesian cell with square domain, based on the Galerkin projection of the Boussinesq equations onto a finite set of empirical eigenfunctions, is presented. The empirical eigenfunctions are obtained from a joint Proper Orthogonal Decomposition (POD) of the velocity and temperature fields using the Snapshot Method on the basis of a direct numerical simulation (DNS). The resulting LDM is a quadratic inhomogeneous system of coupled ordinary differential equations which we use to describe the long-time temporal evolution of the large-scale mode amplitudes for a Rayleigh number of 1e5 and a Prandtl number of 0.7. The truncation to a finite number of degrees of freedom, that does not exceed a number of 310 for the present, requires the additional implementation of an eddy viscosity-diffusivity to capture the missing dissipation of the small-scale modes. The magnitude of this additional dissipation mechanism is determined by requiring statis...

  20. Oscillatory instability of three-dimensional natural convection of air in a laterally heated cubic box

    CERN Document Server

    Gelfgat, Alexander

    2015-01-01

    Transition from steady to oscillatory buoyancy convection of air in a laterally heated cubic box is studied numerically by straight-forward time integration of Boussinesq equations using a series of gradually refined finite volume grids. Horizontal and spanwise cube boundaries are assumed to be either perfectly thermally conducting or perfectly thermally insulated, which results in four different sets of thermal boundary conditions. Critical Grashof numbers are obtained by interpolation of numerically extracted growth/decay rates of oscillations amplitude to zero. Slightly supercritical flow regimes are described by time-averaged flows, snapshots, and spatial distribution of oscillations amplitude. Possible similarities and dissimilarities with two-dimensional instabilities in laterally heated square cavities are discussed. Arguments for grid and time step independence of the results are given.

  1. MHD mixed convective peristaltic motion of nanofluid with Joule heating and thermophoresis effects.

    Science.gov (United States)

    Shehzad, Sabir Ali; Abbasi, Fahad Munir; Hayat, Tasawar; Alsaadi, Fuad

    2014-01-01

    The primary objective of present investigation is to introduce the novel aspect of thermophoresis in the mixed convective peristaltic transport of viscous nanofluid. Viscous dissipation and Joule heating are also taken into account. Problem is modeled using the lubrication approach. Resulting system of equations is solved numerically. Effects of sundry parameters on the velocity, temperature, concentration of nanoparticles and heat and mass transfer rates at the wall are studied through graphs. It is noted that the concentration of nanoparticles near the boundaries is enhanced for larger thermophoresis parameter. However reverse situation is observed for an increase in the value of Brownian motion parameter. Further, the mass transfer rate at the wall significantly decreases when Brownian motion parameter is assigned higher values.

  2. On Convective Dusty Flow Past a Vertical Stretching Sheet with Internal Heat Absorption

    Directory of Open Access Journals (Sweden)

    Raj Nandkeolyar

    2013-01-01

    Full Text Available The steady two-dimensional boundary layer flow of a viscous, incompressible, and electrically conducting dusty fluid past a vertical permeable stretching sheet under the influence of a transverse magnetic field with the viscous and Joule dissipation is investigated. The fluid particles are assumed to be heat absorbing and the temperature at the surface of the sheet is a result of convective heating. The governing nonlinear partial differential equations are transformed to a set of highly nonlinear coupled ordinary differential equations using a suitable similarity transformation and the resulting system is then solved numerically. It is found inter alia that the contributions of viscous and Joule dissipation in the flow are to increase the thickness of the thermal boundary layer.

  3. CFD Analysis of nanofluid forced convection heat transport in laminar flow through a compact pipe

    Science.gov (United States)

    Yu, Kitae; Park, Cheol; Kim, Sedon; Song, Heegun; Jeong, Hyomin

    2017-08-01

    In the present paper, developing laminar forced convection flows were numerically investigated by using water-Al2O3 nano-fluid through a circular compact pipe which has 4.5mm diameter. Each model has a steady state and uniform heat flux (UHF) at the wall. The whole numerical experiments were processed under the Re = 1050 and the nano-fluid models were made by the Alumina volume fraction. A single-phase fluid models were defined through nano-fluid physical and thermal properties calculations, Two-phase model(mixture granular model) were processed in 100nm diameter. The results show that Nusselt number and heat transfer rate are improved as the Al2O3 volume fraction increased. All of the numerical flow simulations are processed by the FLUENT. The results show the increment of thermal transfer from the volume fraction concentration.

  4. Conjugate Heat Transfer in Rayleigh-Bénard Convection in a Square Enclosure

    Directory of Open Access Journals (Sweden)

    Habibis Saleh

    2014-01-01

    Full Text Available Conjugate natural convection-conduction heat transfer in a square enclosure with a finite wall thickness is studied numerically in the present paper. The governing parameters considered are the Rayleigh number 5×103≤Ra≤106, the wall-to-fluid thermal conductivity ratio 0.5≤Kr≤10, and the ratio of wall thickness to its height 0.2≤D≤0.4. The staggered grid arrangement together with MAC method was employed to solve the governing equations. It is found that the fluid flow and the heat transfer can be controlled by the thickness of the bottom wall, the thermal conductivity ratio, and the Rayleigh number.

  5. Bifurcations and chaos in convection taking non-Fourier heat-flux

    Science.gov (United States)

    Layek, G. C.; Pati, N. C.

    2017-11-01

    In this Letter, we report the influences of thermal time-lag on the onset of convection, its bifurcations and chaos of a horizontal layer of Boussinesq fluid heated underneath taking non-Fourier Cattaneo-Christov hyperbolic model for heat propagation. A five-dimensional nonlinear system is obtained for a low-order Galerkin expansion, and it reduces to Lorenz system for Cattaneo number tending to zero. The linear stability agreed with existing results that depend on Cattaneo number C. It also gives a threshold Cattaneo number, CT, above which only oscillatory solutions can persist. The oscillatory solutions branch terminates at the subcritical steady branch with a heteroclinic loop connecting a pair of saddle points for subcritical steady-state solutions. For subcritical onset of convection two stable solutions coexist, that is, hysteresis phenomenon occurs at this stage. The steady solution undergoes a Hopf bifurcation and is of subcritical type for small value of C, while it becomes supercritical for moderate Cattaneo number. The system goes through period-doubling/noisy period-doubling transition to chaos depending on the control parameters. There after the system exhibits Shil'nikov chaos via homoclinic explosion. The complexity of spiral strange attractor is analyzed using fractal dimension and return map.

  6. A NUMERICAL INVESTIGATION OF EFFECT OF MAGNETIC FIELD ON HEAT CONVECTION WITH VARIABLE PHYSICAL PROPERTIES

    Directory of Open Access Journals (Sweden)

    Ziyaddin RECEBLİ

    2008-01-01

    Full Text Available In some studies, the effect of magnetic field on heat convection has been investigated given that physical properties are constant regardless of temperature. The effect of magnetic field on heat convection and fluids whose physical properties change by temperature has been investigated in this study as physical properties of fluids change by the effect of temperature. Momentum, continuity and energy equations including electromagnetic force affecting the fluid were used in the solution. Temperatures at axial and radial directions and Nusselt numbers were calculated depending on magnetic field intensity and other physical properties of fluid by solving the equation system written in cylindrical coordinates system by means of one of the numerical methods which is finite difference method. According to results, velocity and temperature of the cooled fluid decreased following an increase in the intensity of magnetic field placed vertically to flow direction. As determined in the previous one, this study also indicated that the increase in Reynolds number increases Nusselt number, and increasing the effect of magnetic field decreases Nusselt number. The theoretical results of the present study are in conformity with the results of our previous one.

  7. Numerical Investigation of Nanofluid Forced Convection in Channels with Discrete Heat Sources

    Directory of Open Access Journals (Sweden)

    Payam Rahim Mashaei

    2012-01-01

    Full Text Available Numerical simulation is performed to investigate the laminar force convection of Al2O3/water nanofluid in a flow channel with discrete heat sources. The heat sources are placed on the bottom wall of channel which produce much thermal energy that must be evacuated from the system. The remaining surfaces of channel are kept adiabatic to exchange energy between nanofluid and heat sources. In the present study the effects of Reynolds number (Re=50,100,200,400, and 1000, particle volume fraction (=0 (distilled water, 1 and 4% on the average heat transfer coefficient (h, pressure drop (Δ, and wall temperature ( are evaluated. The use of nanofluid can produce an asymmetric velocity along the height of the channel. The results show a maximum value 38% increase in average heat transfer coefficient and 68% increase in pressure drop for all the considered cases when compared to basefluid (i.e., water. It is also observed that the wall temperature decreases remarkably as Re and ϕ increase. Finally, thermal-hydraulic performance (η is evaluated and it is seen that best performance can be obtained for Re=1000 and =4%.

  8. Natural Convection in a Differentially Heated Square Enclosure with a Solid Polygon

    Directory of Open Access Journals (Sweden)

    R. Roslan

    2014-01-01

    Full Text Available The aim of the present numerical study is to analyze the conjugate natural convection heat transfer in a differentially heated square enclosure containing a conductive polygon object. The left wall is heated and the right wall is cooled, while the horizontal walls are kept adiabatic. The COMSOL Multiphysics software is applied to solve the dimensionless governing equations. The governing parameters considered are the polygon type, 3≤N≤∞, the horizontal position, 0.25≤X0≤0.75, the polygon size, 0≤A≤π/16, the thermal conductivity ratio, 0.1≤Kr≤10.0, and the Rayleigh number, 103≤Ra≤106. The critical size of the solid polygon was found exists at low conductivities. The heat transfer rate increases with the increase of the size of the solid polygon, until it reaches its maximum value. Here, the size of the solid polygon is reaches its critical value. Further, beyond this critical size of the solid polygon, will decrease the heat transfer rate.

  9. Heat transport and flow structure in rotating Rayleigh-B\\'enard convection

    CERN Document Server

    Stevens, Richard J A M; Lohse, Detlef

    2013-01-01

    Here we summarize the results from our direct numerical simulations (DNS) and experimental measurements on rotating Rayleigh-B\\'enard (RB) convection. Our experiments and simulations are performed in a cylindrical samples with aspect ratio of $0.5 \\leq \\Gamma\\leq 2.0$. Here \\Gamma=D/L with D and L are the diameter and height of the sample, respectively. When the rotation rate is increased, while a fixed temperature difference between the hot bottom and cold top plate is maintained, a sharp increase in the heat transfer is observed before the heat transfer drops drastically at stronger rotation rates. Here we focus on the question of how the heat transfer enhancement with respect to the non-rotating case depends on the Rayleigh number Ra, the Prandtl number Pr, and the rotation rate, indicated by the Rossby number Ro. Special attention will be given to influence of the aspect ratio on rotation rate that is required to get heat transport enhancement. In addition, we will discuss the relation between the heat tr...

  10. Natural convection in a differentially heated square enclosure with a solid polygon.

    Science.gov (United States)

    Roslan, R; Saleh, H; Hashim, I

    2014-01-01

    The aim of the present numerical study is to analyze the conjugate natural convection heat transfer in a differentially heated square enclosure containing a conductive polygon object. The left wall is heated and the right wall is cooled, while the horizontal walls are kept adiabatic. The COMSOL Multiphysics software is applied to solve the dimensionless governing equations. The governing parameters considered are the polygon type, 3 ≤ N ≤ ∞, the horizontal position, 0.25 ≤ X 0 ≤ 0.75, the polygon size, 0 ≤ A ≤ π/16, the thermal conductivity ratio, 0.1 ≤ K r ≤ 10.0, and the Rayleigh number, 10(3) ≤ Ra ≤ 10(6). The critical size of the solid polygon was found exists at low conductivities. The heat transfer rate increases with the increase of the size of the solid polygon, until it reaches its maximum value. Here, the size of the solid polygon is reaches its critical value. Further, beyond this critical size of the solid polygon, will decrease the heat transfer rate.

  11. Introduction to heat transfer

    CERN Document Server

    SUNDÉN, B

    2012-01-01

    Presenting the basic mechanisms for transfer of heat, Introduction to Heat Transfer gives a deeper and more comprehensive view than existing titles on the subject. Derivation and presentation of analytical and empirical methods are provided for calculation of heat transfer rates and temperature fields as well as pressure drop. The book covers thermal conduction, forced and natural laminar and turbulent convective heat transfer, thermal radiation including participating media, condensation, evaporation and heat exchangers.

  12. Performance evaluation of RANS-based turbulence models in simulating a honeycomb heat sink

    Science.gov (United States)

    Subasi, Abdussamet; Ozsipahi, Mustafa; Sahin, Bayram; Gunes, Hasan

    2017-07-01

    As well-known, there is not a universal turbulence model that can be used to model all engineering problems. There are specific applications for each turbulence model that make it appropriate to use, and it is vital to select an appropriate model and wall function combination that matches the physics of the problem considered. Therefore, in this study, performance of six well-known Reynolds-Averaged Navier-Stokes ( RANS) based turbulence models which are the Standard k {{-}} ɛ, the Renormalized Group k- ɛ, the Realizable k- ɛ, the Reynolds Stress Model, the k- ω and the Shear Stress Transport k- ω and accompanying wall functions which are the standard, the non-equilibrium and the enhanced are evaluated via 3D simulation of a honeycomb heat sink. The CutCell method is used to generate grid for the part including heat sink called test section while a hexahedral mesh is employed to discretize to inlet and outlet sections. A grid convergence study is conducted for verification process while experimental data and well-known correlations are used to validate the numerical results. Prediction of pressure drop along the test section, mean base plate temperature of the heat sink and temperature at the test section outlet are regarded as a measure of the performance of employed models and wall functions. The results indicate that selection of turbulence models and wall functions has a great influence on the results and, therefore, need to be selected carefully. Hydraulic and thermal characteristics of the honeycomb heat sink can be determined in a reasonable accuracy using RANS- based turbulence models provided that a suitable turbulence model and wall function combination is selected.

  13. The role of Stewartson and Ekman layers in turbulent rotating Rayleigh-B\\'enard convection

    CERN Document Server

    Kunnen, Rudie P J; Overkamp, Jim; Sun, Chao; van Heijst, GertJan F; Clercx, Herman J H

    2011-01-01

    When the classical Rayleigh-B\\'enard (RB) system is rotated about its vertical axis roughly three regimes can be identified. In regime I (weak rotation) the large scale circulation (LSC) is the dominant feature of the flow. In regime II (moderate rotation) the LSC is replaced by vertically aligned vortices. Regime III (strong rotation) is characterized by suppression of the vertical velocity fluctuations. Using results from experiments and direct numerical simulations of RB convection for a cell with a diameter-to-height aspect ratio equal to one at $Ra \\sim 10^8-10^9$ ($Pr=4-6$) and $0 \\lesssim 1/Ro \\lesssim 25$ we identified the characteristics of the azimuthal temperature profiles at the sidewall in the different regimes. In regime I the azimuthal wall temperature profile shows a cosine shape and a vertical temperature gradient due to plumes that travel with the LSC close to the sidewall. In regime II and III this cosine profile disappears, but the vertical wall temperature gradient is still observed. It t...

  14. Energy and water cycle over the Tibetan plateau : surface energy balance and turbulent heat fluxes

    NARCIS (Netherlands)

    Su, Zhongbo; Zhang, Ting; Ma, Yaoming; Jia, Li; Wen, Jun

    2006-01-01

    This contribution presents an overview and an outlook of studies on energy and water cycle over the Tibetan plateau with focuses on the estimation of energy balance terms and turbulent heat fluxes. On the basis of the surface energy balance calculations, we show that the phenomena of the energy

  15. Energy and water cycle over the Tibetan Plateau: surface energy balance and turbulent heat fluxes

    NARCIS (Netherlands)

    Su, Z.; Zhang, T.; Ma, Y.; Jia, L.; Wen, J.

    2006-01-01

    This contribution presents an overview and an outlook of studies on energy and water cycle over the Tibetan plateau with focuses on the estimation of energy balance terms and turbulent heat fluxes. On the basis of the surface energy balance calculations, we show that the phenomena of the energy

  16. Heat transfer in particle-laden wall-bounded turbulent flows

    NARCIS (Netherlands)

    Jaszczur, M.; Portela, L.M.

    2006-01-01

    In present work heat transfer in particle-laden wall-bounded turbulent flows has been study with the fluid-particle one way interaction approach. Direct Numerical Simulation of the flow, combined with Lagrangian particle tracking technique has been performed to study the problem. In presented

  17. Temperature regimes and turbulent heat fluxes across a heterogeneous canopy in an Alaskan boreal forest

    Science.gov (United States)

    We evaluate local differences in thermal regimes and turbulent heat fluxes across the heterogeneous canopy of a black spruce boreal forest on discontinuous permafrost in interior Alaska. The data was taken during an intensive observing period in the summer of 2013 from two micrometeorological tower...

  18. Heat and mass transfer in a vertical channel under heat-gravitational convection conditions

    Science.gov (United States)

    Petrichenko, Michail; Nemova, Darya; Reich, Elisaveta; Subbotina, Svetlana; Khayrutdinova, Faina

    2016-03-01

    Heat-gravitational motion of an air flow in a vertical channel with one-sided heating in an area with low Reynolds number is stated in Boussinesq approximation. Hydraulic variables field in a heat-gravitational motion is modeled with the application of ANSYS-FLUENT. It is converted to average velocity and temperature values in a cross section of the channel. The value of an average velocity is determined by rate of heat supply in a barotropic flow with a polytropic coefficient nventilated vertical channel with free air access and in the absence of gaps. In a channel with closed air access inleakage of the cold air through gaps on an unheated side leads to decrease in an average speed at least twice in comparison to channel with free air access.

  19. Scalings for unsteady natural convection boundary layers on an evenly heated plate with time-dependent heating flux

    Science.gov (United States)

    Lin, Wenxian; Armfield, S. W.

    2013-12-01

    It is of fundamental significance, especially with regard to application, to fully understand the flow behavior of unsteady natural convection boundary layers on a vertical plate heated by a time-dependent heat flux. Such an understanding is currently scarce. In this paper, the scaling analysis by Lin et al. [Phys. Rev. E 79, 066313 (2009), 10.1103/PhysRevE.79.066313] using a simple three-region structure for the unsteady natural convection boundary layer of a homogeneous Newtonian fluid with Pr >1 under isothermal heating was substantially extended for the case when the heating is due to a time-varying sinusoidal heat flux. A series of scalings was developed for the thermal boundary thickness, the plate temperature, the viscous boundary thicknesses, and the maximum vertical velocity within the boundary layer, which are the major parameters representing the flow behavior, in terms of the governing parameters of the flow, i.e., the Rayleigh number Ra, the Prandtl number Pr, and the dimensionless natural frequency fn of the time-varying sinusoidal heat flux, at the start-up stage, at the transition time scale which represents the ending of the start-up stage and the beginning of the transitional stage of the boundary-layer development, and at the quasi-steady stage. These scalings were validated by comparison to 10 full numerical solutions of the governing equations with Ra, Pr, and fn in the ranges 106≤Ra≤109, 3≤Pr≤100, and 0.01≤fn≤0.1 and were shown in general to provide an accurate description of the flow at different development stages, except for high-Pr runs in which a further, although weak, Pr dependence is present, which cannot be accurately predicted by the current scaling analysis using the simple three-region structure, attributed to the non-boundary-layer nature of the velocity field with high-Pr fluids. Some scalings at the transition time scale and at the quasi-steady stage also produce noticeable deviations from the numerical results when

  20. Numerical study for nanofluid flow due to a nonlinear curved stretching surface with convective heat and mass conditions

    Directory of Open Access Journals (Sweden)

    Tasawar Hayat

    Full Text Available This article presents the simultaneous effects of convective heat and mass conditions in boundary-layer flow of nanoliquid due to a nonlinear curved stretching surface. A nonlinear curved stretching surface is used to generate the flow. Thermophoretic diffusion and random motion features are also incorporated. Convective heat and mass conditions are imposed at boundary. Suitable variables are utilized to convert the nonlinear partial differential system into nonlinear ordinary differential system. The obtained nonlinear systems are solved numerically through shooting technique. Plots are displayed in order to explore the role of physical flow variables on the solutions. The skin-friction coefficient and local Nusselt and Sherwood numbers are computed and examined. Our findings indicate that the local Nusselt and Sherwood numbers are reduced for larger values of thermophoresis parameter. Keywords: Nonlinear curved stretching surface, Nanoparticles, Convective heat and mass conditions, Numerical solution

  1. The ion cyclotron turbulence generated by a low frequency kinetic Alfvén wave and turbulent heating of ions

    Science.gov (United States)

    Mikhailenko, V. S.; Mikhailenko, V. V.; Lee, Hae June

    2018-01-01

    The ion cyclotron instability driven by a strong kinetic Alfvén wave is investigated as a possible source of anisotropic heating of ions in the sun's corona. We present a novel model of a plasma with coupled inhomogeneous current and shearing flow, which results from the particle's motion in the electric field of the kinetic Alfvén wave of finite wavelength. The investigation is performed employing the non-modal kinetic theory grounded on the shearing mode approach. The solution of the governing linear integral equation for the perturbed potential displays that the flow velocity shear, which for the corona conditions may be above the growth rate of the ion cyclotron instability in the plasma with steady current, changes the exponential growth of the ion cyclotron potential on the power function of time, that impedes the growth of the unstable ion cyclotron wave and reduces the turbulent heating rate of ions across the magnetic field.

  2. Electron Heating at Kinetic Scales in Magnetosheath Turbulence

    Science.gov (United States)

    Chasapis, Alexandros; Matthaeus, W. H.; Parashar, T. N.; Lecontel, O.; Retino, A.; Breuillard, H.; Khotyaintsev, Y.; Vaivads, A.; Lavraud, B.; Eriksson, E.; hide

    2017-01-01

    We present a statistical study of coherent structures at kinetic scales, using data from the Magnetospheric Multiscale mission in the Earths magnetosheath. We implemented the multi-spacecraft partial variance of increments (PVI) technique to detect these structures, which are associated with intermittency at kinetic scales. We examine the properties of the electron heating occurring within such structures. We find that, statistically, structures with a high PVI index are regions of significant electron heating. We also focus on one such structure, a current sheet, which shows some signatures consistent with magnetic reconnection. Strong parallel electron heating coincides with whistler emissions at the edges of the current sheet.

  3. Azimuthal asymmetries of the large-scale circulation in turbulent Rayleigh-Bénard convection

    Science.gov (United States)

    Brown, Eric; Ahlers, Guenter

    2008-10-01

    Previously we published a dynamical model [E. Brown and G. Ahlers, Phys. Fluids 20, 075101 (2008)] for the large-scale-circulation (LSC) dynamics of Rayleigh-Bénard convection in cylindrical containers. The model consists of a pair of stochastic ordinary differential equations, motivated by the Navier-Stokes equations, one each for the strength δ and the orientation θ0 of the LSC. Here we extend it to cases where the rotational invariance of the system is broken by one of several physically relevant perturbations. As an example of this symmetry breaking we present experimental measurements of the LSC dynamics for a container tilted relative to gravity. In that case the model predicts that the buoyancy of the thermal boundary layers encourages fluid to travel along the steepest slope, that it locks the LSC in this direction, and that it strengthens the flow, as seen in experiments. The increase in LSC strength is shown to be responsible for the observed suppression of cessations and azimuthal fluctuations. We predict and observe that for large enough tilt angles, the restoring force that aligns the flow with the slope is strong enough to cause oscillations of the LSC around this orientation. This planar oscillation mode is different from coherent torsional oscillations that have been observed previously. The model was applied also to containers with elliptical cross sections and predicts that the pressure due to the side wall forces the flow into a preferred orientation in the direction of the longest diameter. When the ellipticity is large enough, then oscillations around this orientation are predicted. The model shows that various azimuthal asymmetries will lock the LSC orientation. However, only those that act on the δ-equation (such as tilting relative to gravity) will enhance the LSC strength and suppress cessations and other azimuthal dynamics. Those that affect only the θ0 equation, such as an interaction with Earth's Coriolis force, will align the flow

  4. Thermocapillary convection around gas bubbles: an important natural effect for the enhancement of heat transfer in liquids under microgravity.

    Science.gov (United States)

    Betz, J; Straub, J

    2002-10-01

    In the presence of a temperature gradient at a liquid-gas or liquid-liquid interface, thermocapillary or Marangoni convection develops. This convection is a special type of natural convection that was not paid much attention in heat transfer for a long time, although it is strong enough to drive liquids against the direction of buoyancy on Earth. In a microgravity environment, however, it is the remaining mode of natural convection and supports heat and mass transfer. During boiling in microgravity it was observed at subcooled liquid conditions. Therefore, the question arises about its contribution to heat transfer without phase change. Thermocapillary convection was quantitatively studied at single gas bubbles in various liquids, both experimentally and numerically. A two-dimensional mathematical model described in this article was developed. The coupled mechanism of heat transfer and fluid flow in pure liquids around a single gas bubble was simulated with a control-volume FE-method. The simulation was accompanied and compared with experiments on Earth. The numerical results are in good accordance with the experiments performed on Earth at various Marangoni numbers using various alcohols of varying chain length and Prandtl numbers. As well as calculations on Earth, the numerical method also allows simulations at stationary spherical gas bubbles in a microgravity environment. The results demonstrate that thermocapillary convection is a natural heat transfer mechanism that can partially replace the buoyancy in a microgravity environment, if extreme precautions are taken concerning the purity of the liquids, because impurities accumulate predominantly at the interface. Under Earth conditions, an enhancement of the heat transfer in a liquid volume is even found in the case where thermocapillary flow is counteracted by buoyancy. In particular, the obstructing influence of surface active substances could be observed during the experiments on Earth in water and also in

  5. Forced convective boiling heat transfer of R-410A in horizontal minichannels

    Energy Technology Data Exchange (ETDEWEB)

    Pamitran, A.S.; Choi, Kwang-Il [Graduate School, Chonnam National University, San 96-1, Dunduk-Dong, Yeosu, Chonnam 550 749 (Korea, Republic of); Oh, Jong-Taek [Department of Refrigeration Engineering, Chonnam National University, San 96-1, Dunduk-Dong, Yeosu, Chonnam 550 749 (Korea, Republic of); Oh, Hoo-Kyu [Department of Refrigeration and A/C Engineering, Pukyong National University, 100, Yongdang-Dong, Nam-Ku, Busan 608 739 (Korea, Republic of)

    2007-01-15

    Convective boiling heat transfer experiments were performed in horizontal minichannels with binary mixture refrigerant, R-410A. The test section is made of stainless steel tubes with inner diameters of 1.5mm and 3.0mm and with lengths of 1500mm and 3000mm, respectively, and is uniformly heated by applying electric current directly to the tubes. Local heat transfer coefficients were obtained for a heat flux range of 10-30kWm{sup -2}, a mass flux range of 300-600kgm{sup -2}s{sup -1}, and quality ranges of up to 1.0. The experimental results were mapped on Wang et al.'s (C.C. Wang, C.S. Chiang, D.C. Lu, Visual observation of two-phase flow pattern of R-22, R-134a, and R-407C in a 6.5-mm smooth tube, Experimental, Thermal and Fluid Science 15 (1997) 395-405) and Wojtan et al.'s (L. Wojtan, T. Ursenbacher, J.R. Thome, Investigation of flow boiling in horizontal tubes: part I - a new diabatic two-phase flow pattern map, International Journal of Heat and Mass Transfer 48 (2005) 2955-2969) flow pattern maps to observe the flow regimes. Laminar flow appears in flow with minichannels. A new boiling heat transfer coefficient correlation based on the superposition model for R-410A was developed with 11.20% mean deviation; it showed a good agreement between the measured data and the calculated heat transfer coefficients. (author)

  6. How do patchy snow covers affect turbulent sensible heat fluxes? - Numerical analysis and experimental findings

    Science.gov (United States)

    Schlögl, Sebastian; Mott, Rebecca; Lehning, Michael

    2017-04-01

    The surface energy balance of a snow cover significantly changes once the snow cover gets patchy. The substantial progress in knowledge about the surface energy balance of patchy snow covers is a mandatory requirement to reduce biases in flux parameterizations in larger scale meteorological or climatological models. The aim of this project was to numerically improve energy balance calculations late in the melting season when the spatial variability of turbulent fluxes is especially high owing to the complex feedback between bare/snow-covered areas and the atmosphere above. In order to account for the feedback between the atmosphere and the patchy snow-cover we calculated three-dimensional air temperature and wind velocity fields with the non-hydrostatic atmospheric model ARPS for an idealized flat test site initialized with different snow distributions and atmospheric conditions. The physics-based surface process model Alpine3D has been forced with these atmospheric fields close to the snow surface in order to resolve the small-scale spatial variability. We further initialized the model with atmospheric fields above the blending height as a reference case. The numerical analysis shows that for simulations initialized with fully-resolved atmospheric fields below the blending height, turbulent sensible heat fluxes are up to 50 W/m2 larger than for calculations forced without resolved atmospheric fields. This difference in turbulent sensible heat fluxes over snow increase with increasing number of snow patches and decreasing snow-cover fraction. This is mainly attributed to an increase in the mean near-surface air temperature over snow due to horizontal and vertical exchange processes induced by the heterogeneous land-surface. We used flux footprint estimations to analyse turbulence data measured during three ablation periods in the Dischma valley (Switzerland). This fundamental theory was deployed for eddy-covariance measurements revealing the origin of the measured

  7. Experimental study of convective heat transfer during cooling with low air velocity in a stack of objects

    Energy Technology Data Exchange (ETDEWEB)

    Ben Amara, Sami; Laguerre, Onrawee [Cemagref - Refrigeration Processes Engineering Research Unit, parc de Tourvoie, BP 44, 92163 cedex, Antony (France); Flick, Denis [National Agronomic Institute - INAPG, 16 rue Claude Bernard, 75231 cedex 05, Paris (France)

    2004-12-01

    During cooling with low air velocity (u{<=}0.2 m.s{sup -1}) of a stack of foodstuffs (a few centimeters dimension), the radiation and conduction between products can be of the same order of magnitude as convection. A method was developed to quantify these various transfer modes. The experiment was carried out using an in-line spherical arrangement; however, the same methodology can be applied to other product shapes. The results confirm that the heat transfers by radiation and conduction cannot be neglected. In addition, the convective heat transfer coefficient varies not only with air velocity but also with the product position in the stack. (authors)

  8. Numerical Study of Natural Convection within a Wavy Enclosure Using Meshfree Approach: Effect of Corner Heating

    Directory of Open Access Journals (Sweden)

    Sonam Singh

    2014-01-01

    Full Text Available This paper presents a numerical study of natural convection within a wavy enclosure heated via corner heating. The considered enclosure is a square enclosure with left wavy side wall. The vertical wavy wall of the enclosure and both of the corner heaters are maintained at constant temperature, Tc and Th, respectively, with Th>Tc while the remaining horizontal, bottom, top and side walls are insulated. A penalty element-free Galerkin approach with reduced gauss integration scheme for penalty terms is used to solve momentum and energy equations over the complex domain with wide range of parameters, namely, Rayleigh number (Ra, Prandtl number (Pr, and range of heaters in the x- and y-direction. Numerical results are represented in terms of isotherms, streamlines, and Nusselt number. It is observed that the rate of heat transfer depends to a great extent on the Rayleigh number, Prandtl number, length of the corner heaters and the shape of the heat transfer surface. The consistent performance of the adopted numerical procedure is verified by comparison of the results obtained through the present meshless technique with those existing in the literature.

  9. Heat transfer augmentation of magnetohydrodynamics natural convection in L-shaped cavities utilizing nanofluids

    Directory of Open Access Journals (Sweden)

    Sourtiji Ehsan

    2012-01-01

    Full Text Available A numerical study of natural convection heat transfer through an alumina-water nanofluid inside L-shaped cavities in the presence of an external magnetic field is performed. The study has been carried out for a wide range of important parame­ters such as Rayleigh number, Hartmann number, aspect ratio of the cavity and solid volume fraction of the nanofluid. The influence of the nanoparticle, buoyancy force and the magnetic field on the flow and temperature fields have been plotted and discussed. The results show that after a critical Rayleigh number depending on the aspect ratio, the heat transfer in the cavity rises abruptly due to some significant changes in flow field. It is also found that the heat transfer enhances in the presence of the nanoparticles and increases with solid volume fraction of the nanofluid. In addition, the performance of the nanofluid utilization is more effective at high Ray­leigh numbers. The influence of the magnetic field has been also studied and de­duced that it has a remarkable effect on the heat transfer and flow field in the cavity that as the Hartmann number increases the overall Nusselt number is significantly decreased specially at high Rayleigh numbers.

  10. Numerical simulation of MHD free convection flow in a differentially heated square enclosure with tilted obstacle

    Science.gov (United States)

    Ali, M. M.; Alim, M. A.; Maleque, M. A.; Ahmed, Syed Sabbir

    2017-06-01

    A numerical study has been carried out to analyze the flow and heat transfer characteristics due to the effects of magnetohydrodynamic free convection flow in a differentially heated enclosure having a hot tilted square block. The vertical and horizontal walls of the cavity are non-uniformly heated while the walls of the tilted block are uniformly heated. The basic partial differential equations of the physical problem are solved numerically using finite element technique along with Galerkin's weighted residual simulation. Calculations have been performed for different values of buoyancy parameter (102 ≤ Ra ≤ 105) and magnetic field parameter (0 ≤ Ha ≤ 60) and obtained results are illustrated in terms of streamlines, isotherms, average Nusselt number and average temperature. The results show that the flow pattern and temperature distributions affected noticeably for the effect of aforementioned parameters. In addition, an increase in average Nusselt number is found for the whole range of Rayleigh number and average temperature decreased for increasing Rayleigh number. Comparison between the obtained results and the previously published results on the basis of special case is a good agreement.

  11. Anomalously Weak Solar Convection

    Science.gov (United States)

    Hanasoge, Shravan M.; Duvall, Thomas L.; Sreenivasan, Katepalli R.

    2012-01-01

    Convection in the solar interior is thought to comprise structures on a spectrum of scales. This conclusion emerges from phenomenological studies and numerical simulations, though neither covers the proper range of dynamical parameters of solar convection. Here, we analyze observations of the wavefield in the solar photosphere using techniques of time-distance helioseismology to image flows in the solar interior. We downsample and synthesize 900 billion wavefield observations to produce 3 billion cross-correlations, which we average and fit, measuring 5 million wave travel times. Using these travel times, we deduce the underlying flow systems and study their statistics to bound convective velocity magnitudes in the solar interior, as a function of depth and spherical- harmonic degree l..Within the wavenumber band l convective velocities are 20-100 times weaker than current theoretical estimates. This constraint suggests the prevalence of a different paradigm of turbulence from that predicted by existing models, prompting the question: what mechanism transports the heat flux of a solar luminosity outwards? Advection is dominated by Coriolis forces for wavenumbers l convection may be quasi-geostrophic. The fact that isorotation contours in the Sun are not coaligned with the axis of rotation suggests the presence of a latitudinal entropy gradient.

  12. ELECTRON HEATING IN MAGNETOROTATIONAL INSTABILITY: IMPLICATIONS FOR TURBULENCE STRENGTH IN THE OUTER REGIONS OF PROTOPLANETARY DISKS

    Energy Technology Data Exchange (ETDEWEB)

    Mori, Shoji; Okuzumi, Satoshi, E-mail: mori.s@geo.titech.ac.jp [Department of Earth and Planetary Sciences, Tokyo Institute of Technology, Meguro-ku, Tokyo, 152-8551 (Japan)

    2016-01-20

    The magnetorotational instability (MRI) drives vigorous turbulence in a region of protoplanetary disks where the ionization fraction is sufficiently high. It has recently been shown that the electric field induced by the MRI can heat up electrons and thereby affect the ionization balance in the gas. In particular, in a disk where abundant dust grains are present, the electron heating causes a reduction of the electron abundance, thereby preventing further growth of the MRI. By using the nonlinear Ohm's law that takes into account electron heating, we investigate where in protoplanetary disks this negative feedback between the MRI and ionization chemistry becomes important. We find that the “e-heating zone,” the region where the electron heating limits the saturation of the MRI, extends out up to 80 AU in the minimum-mass solar nebula with abundant submicron-sized grains. This region is considerably larger than the conventional dead zone whose radial extent is ∼20 AU in the same disk model. Scaling arguments show that the MRI turbulence in the e-heating zone should have a significantly lower saturation level. Submicron-sized grains in the e-heating zone are so negatively charged that their collisional growth is unlikely to occur. Our present model neglects ambipolar and Hall diffusion, but our estimate shows that ambipolar diffusion would also affect the MRI in the e-heating zone.

  13. Internal (Annular) and Compressible External (Flat Plate) Turbulent Flow Heat Transfer Correlations.

    Energy Technology Data Exchange (ETDEWEB)

    Dechant, Lawrence [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Smith, Justin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-01-01

    Here we provide a discussion regarding the applicability of a family of traditional heat transfer correlation based models for several (unit level) heat transfer problems associated with flight heat transfer estimates and internal flow heat transfer associated with an experimental simulation design (Dobranich 2014). Variability between semi-empirical free-flight models suggests relative differences for heat transfer coefficients on the order of 10%, while the internal annular flow behavior is larger with differences on the order of 20%. We emphasize that these expressions are strictly valid only for the geometries they have been derived for e.g. the fully developed annular flow or simple external flow problems. Though, the application of flat plate skin friction estimate to cylindrical bodies is a traditional procedure to estimate skin friction and heat transfer, an over-prediction bias is often observed using these approximations for missile type bodies. As a correction for this over-estimate trend, we discuss a simple scaling reduction factor for flat plate turbulent skin friction and heat transfer solutions (correlations) applied to blunt bodies of revolution at zero angle of attack. The method estimates the ratio between axisymmetric and 2-d stagnation point heat transfer skin friction and Stanton number solution expressions for sub-turbulent Reynolds numbers %3C1x10 4 . This factor is assumed to also directly influence the flat plate results applied to the cylindrical portion of the flow and the flat plate correlations are modified by

  14. Turbulent heat and mass transfers across a thermally stratified air-water interface

    Science.gov (United States)

    Papadimitrakis, Y. A.; Hsu, Y.-H. L.; Wu, J.

    1986-01-01

    Rates of heat and mass transfer across an air-water interface were measured in a wind-wave research facility, under various wind and thermal stability conditions (unless otherwise noted, mass refers to water vapor). Heat fluxes were obtained from both the eddy correlation and the profile method, under unstable, neutral, and stable conditions. Mass fluxes were obtained only under unstable stratification from the profile and global method. Under unstable conditions the turbulent Prandtl and Schmidt numbers remain fairly constant and equal to 0.74, whereas the rate of mass transfer varies linearly with bulk Richardson number. Under stable conditions the turbulent Prandtl number rises steadily to a value of 1.4 for a bulk Richardson number of about 0.016. Results of heat and mass transfer, expressed in the form of bulk aerodynamic coefficients with friction velocity as a parameter, are also compared with field data.

  15. Observations of Plasma Turbulence and Heating from the Solar Wind and Simulations

    Science.gov (United States)

    Wicks, R. T.

    2015-12-01

    The cascade of energy by plasma turbulence has been shown to occur in, and heat, the solar wind. Recent work in the study of solar wind turbulence has focussed, in the most part, on advanced data analysis techniques, such as third moment structure functions, wavelets, conditional data sampling, multi-spacecraft observations and reconstruction of 2D k-spectra with tomography, and statistical studies from long time series of spacecraft observations. These techniques are complex and contain different assumptions about the qualities of the data underpinning the measurements. Here, we will review recent advances and discoveries in the study of plasma turbulence from solar wind data analysis and discuss how benchmarking of techniques against one another could be pursued and how simulations can be used to aid in the understanding of the results of solar wind data analysis, in particular in the framework of the "Turbulence Dissipation Challenge" (Parashar et al., Journal of Plasma Physics, Volume 81, Issue 05, 905810513, 2015). We will pay particular attention to observing two different heating mechanisms: stochastic heating and resonant wave-particle interactions. The magnetic helicity of the solar wind is shown to separate into two distinct components, one originating from pseudo-Alfvenic (k may have a component parallel to the magnetic field) and one from the Alfvenic fluctuations (k is strictly perpendicular). The solar wind results are compared with "pseudo-spacecraft" data from large 3D PIC simulations.

  16. Heat and mass transfer in a vertical channel under heat-gravitational convection conditions

    Directory of Open Access Journals (Sweden)

    Petrichenko Michail

    2016-01-01

    Full Text Available Heat-gravitational motion of an air flow in a vertical channel with one-sided heating in an area with low Reynolds number is stated in Boussinesq approximation. Hydraulic variables field in a heat-gravitational motion is modeled with the application of ANSYS-FLUENT. It is converted to average velocity and temperature values in a cross section of the channel. The value of an average velocity is determined by rate of heat supply in a barotropic flow with a polytropic coefficient n

  17. Experimental investigation of the influence of the air jet trajectory on convective heat transfer in buildings equipped with air-based and radiant cooling systems

    DEFF Research Database (Denmark)

    Le Dreau, Jerome; Heiselberg, Per; Jensen, Rasmus Lund

    2015-01-01

    -state and dynamic conditions. With the air-based cooling system, a dependency of the convective heat transfer on the air jet trajectory has been observed. New correlations have been developed, introducing a modified Archimedes number to account for the air flow pattern. The accuracy of the new correlations has been...... evaluated to±15%. Besides the study with an air-based cooling system, the convective heat transfer with a radiant cooling system has also been investigated. The convective flow at the activated surface is mainly driven by natural convection. For other surfaces, the complexity of the flow and the large......The complexity and diversity of airflow in buildings make the accurate definition of convective heat transfer coefficients (CHTCs) difficult. In a full-scale test facility, the convective heat transfer of two cooling systems (active chilled beam and radiant wall) has been investigated under steady...

  18. Experimental investigation of heat transfer and flow pattern from heated horizontal rectangular fin array under natural convection

    Science.gov (United States)

    Taji, S. G.; Parishwad, G. V.; Sane, N. K.

    2014-07-01

    This paper presents results of the experimental study conducted on heated horizontal rectangular fin array under natural convection. The temperature mapping and the prediction of the flow patterns over the fin array with variable fin spacing is carried out. Dimensionless fin spacing to height (S/H) ratio is varied from 0.05 to 0.3 and length to height ratio (L/H) = 5 is kept constant. The heater input to the fin array assembly is varied from 25 to 100 W. The single chimney flow pattern is observed from 8 to 12 mm fin spacing. The end flow is choked below 6 mm fin spacing. The single chimney flow pattern changes to sliding or end flow choking at 6 mm fin spacing. The average heat transfer coefficient (ha) is very small (2.52-5.78 W/m2 K) at 100 W for S = 5-12 mm. The ha is very small (1.12-1.8 W/m2 K) at 100 W for 2-4 mm fin spacing due to choked fin array end condition. The end flow is not sufficient to reach up to central portion of fin array and in the middle portion there is an unsteady down and up flow pattern resulting in sliding chimney. The central bottom portion of fin array channel does not contribute much in heat dissipation for S = 2-4 mm. The ha has significantly improved at higher spacing as compared to lower spacing region. The single chimney flow pattern is preferred from heat transfer point of view. The optimum spacing is confirmed in the range of 8-10 mm. The average heat transfer results are compared with previous literature and showed similar trend and satisfactory agreement. An empirical equation has been proposed to correlate the average Nusselt number as a function of Grashof number and fin spacing to height ratio. The average error for this equation is -0.32 %.

  19. Double stratification effects on unsteady electrical MHD mixed convection flow of nanofluid with viscous dissipation and Joule heating

    Directory of Open Access Journals (Sweden)

    Yahaya Shagaiya Daniel

    2017-10-01

    Full Text Available The problem of unsteady mixed convection electrical magnetohydrodynamic (MHD flow and heat transfer induced due to nanofluid over a permeable stretching sheet using Buongiorno model is investigated. The transverse electric and magnetic fields are considered in the flow field, while in the heat convection is associated with the thermal radiation, heat generation/absorption, viscous and Ohmic dissipations, and chemical reaction is incorporated in the mass diffusion. A similarity transformation is used to reduce the boundary layer governing equations which are partial differential equations to nonlinear differential equations and then solved numerically using implicit finite difference scheme. The nanofluid velocity and temperature are sensitive to an increase in the electric field, which resolved the problem of sticky effects due to the magnetic field. Destructive chemical reaction increases the level nanoparticles concentration while reversed behave happened in the case of the generative chemical reaction. Heat source boosts the fluid temperature while as opposite occurred with the heat sink. Thermal and concentration stratifications decreased the fluid temperature and the nanoparticles concentration profiles. Buoyancy ratio parameter reduced the Nusselt and Sherwood numbers whereas mixed convection parameter increases for higher values. A comparison with the previous study available in literature has been done and found an excellent agreement with the published data. Keywords: Magnetic nanofluid, Doubly stratified flow, Mixed convection, Thermal radiation, Electric field, Viscous and Ohmic dissipations

  20. Stochastic Convection Parameterizations

    Science.gov (United States)

    Teixeira, Joao; Reynolds, Carolyn; Suselj, Kay; Matheou, Georgios

    2012-01-01

    computational fluid dynamics, radiation, clouds, turbulence, convection, gravity waves, surface interaction, radiation interaction, cloud and aerosol microphysics, complexity (vegetation, biogeochemistry, radiation versus turbulence/convection stochastic approach, non-linearities, Monte Carlo, high resolutions, large-Eddy Simulations, cloud structure, plumes, saturation in tropics, forecasting, parameterizations, stochastic, radiation-clod interaction, hurricane forecasts

  1. Simple heat transfer correlations for turbulent tube flow

    Directory of Open Access Journals (Sweden)

    Taler Dawid

    2017-01-01

    Full Text Available The paper presents three power-type correlations of a simple form, which are valid for Reynolds numbers range from 3·103 ≤ Re ≤ 106, and for three different ranges of Prandtl number: 0.1 ≤ Pr ≤ 1.0, 1.0 < Pr ≤ 3.0, and 3.0 < Pr ≤ 103. Heat transfer correlations developed in the paper were compared with experimental results available in the literature. The comparisons performed in the paper confirm the good accuracy of the proposed correlations. They are also much simpler compared with the relationship of Gnielinski, which is also widely used in the heat transfer calculations.

  2. Circulation and Convection in the Irminger Sea

    Science.gov (United States)

    2010-02-01

    area than in any other ocean ( Sabine et al., 2004). Atmospheric variabil- ity, primarily NAO-related, strongly impacts convective activity as well as...east of Cape Farewell were compromised. Turbulent heat fluxes were computed using a bulk formula (COARE 3.0, Fairall et al., 2003) with the inputs of...background levels (Fig. 2-6c). Replacing the ERA-40 wind speed with our estimate of the true wind speed in the bulk formula raised the heat fluxes in

  3. Heat transfer by natural convection into an horizontal cavity; Transferencia de calor por conveccion natural en una cavidad horizontal

    Energy Technology Data Exchange (ETDEWEB)

    Arevalo J, P

    1998-12-31

    At this thesis it is studied the heat transfer by natural convection in an horizontal cavity, it is involved a boiling`s part that is described the regimes and correlations differences for boiling`s curve. It is designed a horizontal cavity for realize the experimental part and it`s mention from equipment or instrumentation to succeed in a experimentation that permits to realize the analysis of heat transfer, handling as water fluid at atmospheric pressure and where it`s present process from natural convection involving part boiling`s subcooled. The system consists of heater zone submerged in a horizontal cavity with water. Once part finished experimental with information to obtained it`s proceeded to obtain a correlation, realized starting from analysis dimensionless such as: Jakob, Bond and Grasoft (Boiling) besides of knows in natural convection: Prandtl and Nusselt. The mathematical model explains the behavior for natural convection continued part boiling`s subcooled. It is realize analysis graphics too where it`s show comparing with Globe Dropkin and Catton equations by natural convection with bottom heating. (Author)

  4. TRMM Convective and Stratiform Heating L3 1 month 0.5 degree x 0.5 degree V6 (TRMM_CSH) at GES DISC

    Data.gov (United States)

    National Aeronautics and Space Administration — These data are output from the Goddard Convective-Stratiform Heating (CSH) algorithm. The dataset contains global 0.5 x 0.5 monthly latent heating profiles from...

  5. Maxwell-Cattaneo Heat Convection and Thermal Stresses Responses of a Semi-Infinite Medium to High-Speed Laser Heating due to High Speed Laser Heating

    Directory of Open Access Journals (Sweden)

    Abdallah I. A.

    2009-07-01

    Full Text Available Based on Maxwell-Cattaneo convection equation, the thermoelasticity problem is in- vestigated in this paper. The analytic solution of a boundary value problem for a semi- infinite medium with traction free surface heated by a high-speed laser-pulses have Dirac temporal profile is solved. The temperature, the displacement and the stresses distributions are obtained analytically using the Laplace transformation, and discussed at small time duration of the laser pulses. A numerical study for Cu as a target is performed. The results are presented graphically. The obtained results indicate that the small time duration of the laser pulses has no e ect on the finite velocity of the heat con- ductivity, but the behavior of the stress and the displacement distribution are affected due to the pulsed heating process and due to the structure of the governing equations.

  6. Oxygen Ion Heat Rate within Alfvenic Turbulence in the Cusp

    Science.gov (United States)

    Coffey, Victoria N.; Singh, Nagendra; Chandler, Michael O.

    2009-01-01

    The role that the cleft/cusp has in ionosphere-magnetosphere coupling makes it a dynamic and important region. It is directly exposed to the solar wind, making it possible for the entry of electromagnetic energy and precipitating electrons and ions from dayside reconnection and other dayside events. It is also a significant source of ionospheric plasma, contributing largely to the mass loading of the magnetosphere with large fluxes of outflowing ions. Crossing the cusp/cleft near 5100 km, the Polar instruments observe the common correlation of downward Poynting flux, ion energization, soft electron precipitation, broadband extremely low-frequency (BB-ELF) emissions, and density depletions. The dominant power in the BB-ELF emissions is now identified to be from spatially broad, low frequency Alfv nic structures. For a cusp crossing, we determine using the Electric Field Investigation (EFI), that the electric and magnetic field fluctuations are Alfv nic and the electric field gradients satisfy the inequality for stochastic acceleration. With all the Polar 1996 horizontal crossings of the cusp, we determine the O+ heating rate using the Thermal Ion Dynamics Experiment (TIDE) and Plasma Wave Investigation (PWI). We then compare this heating rate to other heating rates assuming the electric field gradient criteria exceeds the limit for stochastic acceleration for the remaining crossings. The comparison suggests that a stochastic acceleration mechanism is operational and the heating is controlled by the transverse spatial scale of the Alfvenic waves.

  7. Conceptual Design of Forced Convection Molten Salt Heat Transfer Testing Loop

    Energy Technology Data Exchange (ETDEWEB)

    Manohar S. Sohal; Piyush Sabharwall; Pattrick Calderoni; Alan K. Wertsching; S. Brandon Grover

    2010-09-01

    This report develops a proposal to design and construct a forced convection test loop. A detailed test plan will then be conducted to obtain data on heat transfer, thermodynamic, and corrosion characteristics of the molten salts and fluid-solid interaction. In particular, this report outlines an experimental research and development test plan. The most important initial requirement for heat transfer test of molten salt systems is the establishment of reference coolant materials to use in the experiments. An earlier report produced within the same project highlighted how thermophysical properties of the materials that directly impact the heat transfer behavior are strongly correlated to the composition and impurities concentration of the melt. It is therefore essential to establish laboratory techniques that can measure the melt composition, and to develop purification methods that would allow the production of large quantities of coolant with the desired purity. A companion report describes the options available to reach such objectives. In particular, that report outlines an experimental research and development test plan that would include following steps: •Molten Salts: The candidate molten salts for investigation will be selected. •Materials of Construction: Materials of construction for the test loop, heat exchangers, and fluid-solid corrosion tests in the test loop will also be selected. •Scaling Analysis: Scaling analysis to design the test loop will be performed. •Test Plan: A comprehensive test plan to include all the tests that are being planned in the short and long term time frame will be developed. •Design the Test Loop: The forced convection test loop will be designed including extensive mechanical design, instrument selection, data acquisition system, safety requirements, and related precautionary measures. •Fabricate the Test Loop. •Perform the Tests. •Uncertainty Analysis: As a part of the data collection, uncertainty analysis will

  8. Experimental study on forced convective and subcooled flow boiling heat transfer coefficient of water-ethanol mixtures: an application in cooling of heat dissipative devices

    Science.gov (United States)

    Suhas, B. G.; Sathyabhama, A.

    2018-02-01

    The experimental study is carried out to determine forced convective and subcooled flow boiling heat transfer coefficient in conventional rectangular channels. The fluid is passed through rectangular channels of 0.01 m depth, 0.01 m width, and 0.15 m length. The parameters varied are heat flux, mass flux, inlet temperature and volume fraction of ethanol. Forced convective heat transfer coefficient increases with increase in heat flux and mass flux, but effect of mass flux is less significant. Subcooled flow boiling heat transfer increases with increase in heat flux and mass flux, but the effect of heat flux is dominant. During the subcooled flow boiling region, the effect of mass flux will not influence the heat transfer. The strong Marangoni effect will increase the heat transfer coeffient for mixture with 25% ethanol volume fraction. The results obtained for subcooled flow boiling heat transfer coefficient of water are compared with available literature correlations. It is found that Liu-Winterton equation predicts the experimental results better when compared with that of other literature correlations. An empirical correlation for subcooled flow boiling heat transfer coefficient as a function of mixture wall super heat, mass flux, volume fractions and inlet temperature is developed from the experimental results.

  9. Experimental study on forced convective and subcooled flow boiling heat transfer coefficient of water-ethanol mixtures: an application in cooling of heat dissipative devices

    Science.gov (United States)

    Suhas, B. G.; Sathyabhama, A.

    2017-08-01

    The experimental study is carried out to determine forced convective and subcooled flow boiling heat transfer coefficient in conventional rectangular channels. The fluid is passed through rectangular channels of 0.01 m depth, 0.01 m width, and 0.15 m length. The parameters varied are heat flux, mass flux, inlet temperature and volume fraction of ethanol. Forced convective heat transfer coefficient increases with increase in heat flux and mass flux, but effect of mass flux is less significant. Subcooled flow boiling heat transfer increases with increase in heat flux and mass flux, but the effect of heat flux is dominant. During the subcooled flow boiling region, the effect of mass flux will not influence the heat transfer. The strong Marangoni effect will increase the heat transfer coeffient for mixture with 25% ethanol volume fraction. The results obtained for subcooled flow boiling heat transfer coefficient of water are compared with available literature correlations. It is found that Liu-Winterton equation predicts the experimental results better when compared with that of other literature correlations. An empirical correlation for subcooled flow boiling heat transfer coefficient as a function of mixture wall super heat, mass flux, volume fractions and inlet temperature is developed from the experimental results.

  10. Differential kinetic dynamics and heating of ions in the turbulent solar wind

    CERN Document Server

    Valentini, F; Stabile, S; Pezzi, O; Servidio, S; De Marco, R; Marcucci, F; Bruno, R; Lavraud, B; De Keyser, J; Consolini, G; Brienza, D; Sorriso-Valvo, L; Retinò, A; Vaivads, A; Salatti, M; Veltri, P

    2016-01-01

    The solar wind plasma is a fully ionized and turbulent gas ejected by the outer layers of the solar corona at very high speed, mainly composed by protons and electrons, with a small percentage of helium nuclei and a significantly lower abundance of heavier ions. Since particle collisions are practically negligible, the solar wind is typically not in a state of thermodynamic equilibrium. Such a complex system must be described through self-consistent and fully nonlinear models, taking into account its multi-species composition and turbulence. We use a kinetic hybrid Vlasov-Maxwell numerical code to reproduce the turbulent energy cascade down to ion kinetic scales, in typical conditions of the uncontaminated solar wind plasma, with the aim of exploring the differential kinetic dynamics of the dominant ion species, namely protons and alpha particles. We show that the response of different species to the fluctuating electromagnetic fields is different. In particular, a significant differential heating of alphas w...

  11. The study and development of the empirical correlations equation of natural convection heat transfer on vertical rectangular sub-channels

    Science.gov (United States)

    Kamajaya, Ketut; Umar, Efrizon; Sudjatmi, K. S.

    2012-06-01

    This study focused on natural convection heat transfer using a vertical rectangular sub-channel and water as the coolant fluid. To conduct this study has been made pipe heaters are equipped with thermocouples. Each heater is equipped with five thermocouples along the heating pipes. The diameter of each heater is 2.54 cm and 45 cm in length. The distance between the central heating and the pitch is 29.5 cm. Test equipment is equipped with a primary cooling system, a secondary cooling system and a heat exchanger. The purpose of this study is to obtain new empirical correlations equations of the vertical rectangular sub-channel, especially for the natural convection heat transfer within a bundle of vertical cylinders rectangular arrangement sub-channels. The empirical correlation equation can support the thermo-hydraulic analysis of research nuclear reactors that utilize cylindrical fuel rods, and also can be used in designing of baffle-free vertical shell and tube heat exchangers. The results of this study that the empirical correlation equations of natural convection heat transfer coefficients with rectangular arrangement is Nu = 6.3357 (Ra.Dh/x)0.0740.

  12. Spatial transport and spectral transfer of solar wind turbulence composed of Alfvén waves and convective structures II: numerical results

    Directory of Open Access Journals (Sweden)

    J. M. Schmidt

    1995-05-01

    Full Text Available This work follows the paper titled "Spatial transport and spectral transfer of solar wind turbulence composed of Alfvén waves and convective structures I: The theoretical model", and deals with the detailed physics and numerical solution of a two-component solar wind model, consisting of small-scale Alfvén waves and convected structures. In particular, we present numerical results which qualitatively reflect many of the observed features of the radial and spectral evolution of the turbulent energies, the residual energy, the cross-helicity and Alfvén-ratio in high-speed solar wind streams. These features are the following: the formation of a characteristic "inclined eye", which evolves between the energy spectra displayed over the frequency axis and tends to close in the radial development of the spectra, a steepening of all spectra towards Kolmogorov-like f-5/3 spectra, the development of the normalized cross-helicity towards a constant not much less than one and the formation of a "trough" form of the Alfvén ratio with a z-shaped left boundary, By weighting special terms in the equations differently, we can also cast light on the physical role of parametric conversion model terms, wave-structure scattering model terms, nonlinear terms, spherical expansion terms and their effects on the radial evolution of turbulent energies in high-speed solar wind streams.

  13. Exact solution for heat transfer free convection flow of Maxwell nanofluids with graphene nanoparticles

    Science.gov (United States)

    Aman, Sidra; Zuki Salleh, Mohd; Ismail, Zulkhibri; Khan, Ilyas

    2017-09-01

    This article focuses on the flow of Maxwell nanofluids with graphene nanoparticles over a vertical plate (static) with constant wall temperature. Possessing high thermal conductivity, engine oil is useful to be chosen as base fluid with free convection. The problem is modelled in terms of PDE’s with boundary conditions. Some suitable non-dimensional variables are interposed to transform the governing equations into dimensionless form. The generated equations are solved via Laplace transform technique. Exact solutions are evaluated for velocity and temperature. These solutions are significantly controlled by some parameters involved. Temperature rises with elevation in volume fraction while Velocity decreases with increment in volume fraction. A comparison with previous published results are established and discussed. Moreover, a detailed discussion is made for influence of volume fraction on the flow and heat profile.

  14. Flow reversal of laminar mixed convection in the entry region of symmetrically heated, vertical plate channels

    Energy Technology Data Exchange (ETDEWEB)

    Desrayaud, G. [Universite de Picardie Jules Verne, INSSET, Lab. Modelisation et Simulation Multi Echelle, MSME FRE 3160 CNRS, 02 - Saint-Quentin (France); Lauriat, G. [Universite Paris-Est, Lab. Modelisation et Simulation Multi Echelle, MSME FRE 3160 CNRS, 77 - Marne-la-Vallee (France)

    2009-11-15

    The present numerical investigation is concerned with flow reversal phenomena for laminar, mixed convection of air in a vertical parallel-plate channel of finite length. Results are obtained for buoyancy-assisted flow in a symmetrically heated channel with uniform wall temperatures for various Grashof numbers and Reynolds numbers in the range 300 {<=} Re {<=} 1300. The effects of buoyancy forces on the flow pattern are investigated and the shapes of velocity and temperature profiles are discussed in detail. Flow reversals centred in the entrance of the channel are predicted. The strength of the cells decreases as the Reynolds number is increased, until they disappear. The regime of reversed flow is identified for high values of the Peclet number in a Pe-Gr/Re map. It is also shown that the channel length has no influence on the occurrence of the reversal flow provided that H/D {>=} 10. (authors)

  15. Heat Transfer in MHD Mixed Convection Flow of a Ferrofluid along a Vertical Channel.

    Directory of Open Access Journals (Sweden)

    Aaiza Gul

    Full Text Available This study investigated heat transfer in magnetohydrodynamic (MHD mixed convection flow of ferrofluid along a vertical channel. The channel with non-uniform wall temperatures was taken in a vertical direction with transverse magnetic field. Water with nanoparticles of magnetite (Fe3O4 was selected as a conventional base fluid. In addition, non-magnetic (Al2O3 aluminium oxide nanoparticles were also used. Comparison between magnetic and magnetite nanoparticles were also conducted. Fluid motion was originated due to buoyancy force together with applied pressure gradient. The problem was modelled in terms of partial differential equations with physical boundary conditions. Analytical solutions were obtained for velocity and temperature. Graphical results were plotted and discussed. It was found that temperature and velocity of ferrofluids depend strongly on viscosity and thermal conductivity together with magnetic field. The results of the present study when compared concurred with published work.

  16. Heat Transfer in MHD Mixed Convection Flow of a Ferrofluid along a Vertical Channel.

    Science.gov (United States)

    Gul, Aaiza; Khan, Ilyas; Shafie, Sharidan; Khalid, Asma; Khan, Arshad

    2015-01-01

    This study investigated heat transfer in magnetohydrodynamic (MHD) mixed convection flow of ferrofluid along a vertical channel. The channel with non-uniform wall temperatures was taken in a vertical direction with transverse magnetic field. Water with nanoparticles of magnetite (Fe3O4) was selected as a conventional base fluid. In addition, non-magnetic (Al2O3) aluminium oxide nanoparticles were also used. Comparison between magnetic and magnetite nanoparticles were also conducted. Fluid motion was originated due to buoyancy force together with applied pressure gradient. The problem was modelled in terms of partial differential equations with physical boundary conditions. Analytical solutions were obtained for velocity and temperature. Graphical results were plotted and discussed. It was found that temperature and velocity of ferrofluids depend strongly on viscosity and thermal conductivity together with magnetic field. The results of the present study when compared concurred with published work.

  17. NUMERICAL STUDY OF DEVELOPING LAMINAR FORCED CONVECTION OF A NANOFLUID HEAT TRANSFER IN AN ANNULAR HORIZONTAL PIPE

    Directory of Open Access Journals (Sweden)

    M BENKHEDDA

    2014-12-01

    Full Text Available This study reports numerical simulation for 3D laminar forced convection of a nanofluid flow in horizontal annulus with constant heat flux at the outer cylinder will the inner cylinder is considered adiabatic. The numerical model is carried out by solving the governing equation of continuity, momentum and energy using take account for thee finite volume method, with the assistance of SIMPLER algorithm. The results shows that for the Reynolds numbers and Prandtl fixed, the dimensionless velocity profile for the laminar forced convection of a nanofluid consisting of water does not vary with the volume concentration of nanoparticles while the effect of the concentration of nanoparticles on the temperature of the mass is significant nanofluid. These results are consistent with those found in the literature. In general the use of nanofluid with a volume concentration of nanoparticles causes a increase in the coefficient of heat transfer by convection.

  18. Mixed convection boundary layer flow of viscoelastic nanofluid past a horizontal circular cylinder: Case of constant heat flux

    Science.gov (United States)

    Mahat, Rahimah; Afiqah Rawi, Noraihan; Kasim, Abdul Rahman Mohd; Shafie, Sharidan

    2017-09-01

    The steady of two-dimensional convection boundary layer flow of a viscoelastic nanofluid over a circular cylinder is investigated in this paper. Carboxymethyl cellulose solution (CMC) is chosen as the base fluid and copper as a nanoparticle with the Prandtl number Pr = 6.2. The governing boundary layer partial differential equations are transformed into dimensionless forms. Then they are solved numerically by using the Keller-Box method. This paper focus on the effects of selected parameter on the flow and heat transfer characteristics and be presented in graphs. The results show that, the velocity profiles and the temperature profiles are increased by increasing the values of nanoparticles volume fraction. While velocity profile decreases when viscoelastic parameter is increase. The reverse trend is observed for the temperature profiles. Also, the values of reduced skin friction are increased by increasing mixed convection parameter, but the values of heat transfer coefficient produce an opposite behaviour with an increasing in mixed convection parameter.

  19. Experimental investigation of a solar dryer with natural convective heat flow

    Energy Technology Data Exchange (ETDEWEB)

    Gbaha, P.; Yobouet Andoh, H.; Kouassi Saraka, J. [Laboratoire d' Energies d' Energies Nouvelles et Renouvelables, Institut National Polytechnique Felix Houphoeuet-Boigny, B.P. 1526 Yamoussoukro (Ivory Coast); Kamenan Koua, B.; Toure, S. [Laboratoire d' Energie Solaire, Universite de Cocody, 22 B.P.: 582, Abidjan 22 (Ivory Coast)

    2007-09-15

    A direct type natural convection solar dryer is designed. It is constructed in local materials (wood, blades of glass, metals) then tested experimentally in foodstuffs drying (cassava, bananas, mango). It is about an experimental approach which consists in analyzing the behavior of the dryer. The study relates mainly kinetics and establishment of drying heat balances. The influence of significant parameters governing heat and mass transfers, such as solar incident radiation, drying air mass flow and effectiveness, is analyzed in order to evaluate its thermal performances. Experimental data can be represented by empirical correlations of the form M(t)=M{sub i}exp(-kt) for representation of drying process. The resolution of these drying equations makes-possible to predict total drying time of each product. Moreover, this drying process allows to reduce the moisture content of cassava and sweet banana approximately to 80% in 19 and 22 h, respectively to reach the safety threshold value of 13%. This value permits the conservation of these products about one year without deterioration. The determination of parameters, like ambient temperature, drying chamber temperature, drying air mass flow and incident heat fluxes, allow to predict the drying effectiveness for modeling and refining the dimensioning of the elaborate prototype. (author)

  20. 3D modelling of coupled mass and heat transfer of a convection-oven roasting process.

    Science.gov (United States)

    Feyissa, Aberham Hailu; Gernaey, Krist V; Adler-Nissen, Jens

    2013-04-01

    A 3D mathematical model of coupled heat and mass transfer describing oven roasting of meat has been developed from first principles. The proposed mechanism for the mass transfer of water is modified and based on a critical literature review of the effect of heat on meat. The model equations are based on a conservation of mass and energy, coupled through Darcy's equations of porous media - the water flow is mainly pressure-driven. The developed model together with theoretical and experimental assessments were used to explain the heat and water transport and the effect of the change in microstructure (permeability, water binding capacity and elastic modulus) that occur during the meat roasting process. The developed coupled partial differential equations were solved by using COMSOL Multiphysics®3.5 and state variables are predicted as functions of both position and time. The proposed mechanism was partially validated by experiments in a convection oven where temperatures were measured online. Copyright © 2012 Elsevier Ltd. All rights reserved.