WorldWideScience

Sample records for controlled pulsed laser

  1. Pulse front adaptive optics: a new method for control of ultrashort laser pulses.

    Science.gov (United States)

    Sun, Bangshan; Salter, Patrick S; Booth, Martin J

    2015-07-27

    Ultrafast lasers enable a wide range of physics research and the manipulation of short pulses is a critical part of the ultrafast tool kit. Current methods of laser pulse shaping are usually considered separately in either the spatial or the temporal domain, but laser pulses are complex entities existing in four dimensions, so full freedom of manipulation requires advanced forms of spatiotemporal control. We demonstrate through a combination of adaptable diffractive and reflective optical elements - a liquid crystal spatial light modulator (SLM) and a deformable mirror (DM) - decoupled spatial control over the pulse front (temporal group delay) and phase front of an ultra-short pulse was enabled. Pulse front modulation was confirmed through autocorrelation measurements. This new adaptive optics technique, for the first time enabling in principle arbitrary shaping of the pulse front, promises to offer a further level of control for ultrafast lasers.

  2. Excitation and Control of Plasma Wakefields by Multiple Laser Pulses

    Science.gov (United States)

    Cowley, J.; Thornton, C.; Arran, C.; Shalloo, R. J.; Corner, L.; Cheung, G.; Gregory, C. D.; Mangles, S. P. D.; Matlis, N. H.; Symes, D. R.; Walczak, R.; Hooker, S. M.

    2017-07-01

    We demonstrate experimentally the resonant excitation of plasma waves by trains of laser pulses. We also take an important first step to achieving an energy recovery plasma accelerator by showing that a plasma wave can be damped by an out-of-resonance trailing laser pulse. The measured laser wakefields are found to be in excellent agreement with analytical and numerical models of wakefield excitation in the linear regime. Our results indicate a promising direction for achieving highly controlled, GeV-scale laser-plasma accelerators operating at multikilohertz repetition rates.

  3. Short-pulse lasers for weather control

    Science.gov (United States)

    Wolf, J. P.

    2018-02-01

    Filamentation of ultra-short TW-class lasers recently opened new perspectives in atmospheric research. Laser filaments are self-sustained light structures of 0.1–1 mm in diameter, spanning over hundreds of meters in length, and producing a low density plasma (1015–1017 cm‑3) along their path. They stem from the dynamic balance between Kerr self-focusing and defocusing by the self-generated plasma and/or non-linear polarization saturation. While non-linearly propagating in air, these filamentary structures produce a coherent supercontinuum (from 230 nm to 4 µm, for a 800 nm laser wavelength) by self-phase modulation (SPM), which can be used for remote 3D-monitoring of atmospheric components by Lidar (Light Detection and Ranging). However, due to their high intensity (1013–1014 W cm‑2), they also modify the chemical composition of the air via photo-ionization and photo-dissociation of the molecules and aerosols present in the laser path. These unique properties were recently exploited for investigating the capability of modulating some key atmospheric processes, like lightning from thunderclouds, water vapor condensation, fog formation and dissipation, and light scattering (albedo) from high altitude clouds for radiative forcing management. Here we review recent spectacular advances in this context, achieved both in the laboratory and in the field, reveal their underlying mechanisms, and discuss the applicability of using these new non-linear photonic catalysts for real scale weather control.

  4. Short-pulse lasers for weather control.

    Science.gov (United States)

    Wolf, J P

    2018-02-01

    Filamentation of ultra-short TW-class lasers recently opened new perspectives in atmospheric research. Laser filaments are self-sustained light structures of 0.1-1 mm in diameter, spanning over hundreds of meters in length, and producing a low density plasma (1015-1017 cm-3) along their path. They stem from the dynamic balance between Kerr self-focusing and defocusing by the self-generated plasma and/or non-linear polarization saturation. While non-linearly propagating in air, these filamentary structures produce a coherent supercontinuum (from 230 nm to 4 µm, for a 800 nm laser wavelength) by self-phase modulation (SPM), which can be used for remote 3D-monitoring of atmospheric components by Lidar (Light Detection and Ranging). However, due to their high intensity (1013-1014 W cm-2), they also modify the chemical composition of the air via photo-ionization and photo-dissociation of the molecules and aerosols present in the laser path. These unique properties were recently exploited for investigating the capability of modulating some key atmospheric processes, like lightning from thunderclouds, water vapor condensation, fog formation and dissipation, and light scattering (albedo) from high altitude clouds for radiative forcing management. Here we review recent spectacular advances in this context, achieved both in the laboratory and in the field, reveal their underlying mechanisms, and discuss the applicability of using these new non-linear photonic catalysts for real scale weather control.

  5. Two-pulse laser control of nuclear and electronic motion

    DEFF Research Database (Denmark)

    Grønager, Michael; Henriksen, Niels Engholm

    1997-01-01

    We discuss an explicitly time-dependent two-pulse laser scheme for controlling where nuclei and electrons are going in unimolecular reactions. We focus on electronic motion and show, with HD+ as an example, that one can find non-stationary states where the electron (with some probability) oscilla......We discuss an explicitly time-dependent two-pulse laser scheme for controlling where nuclei and electrons are going in unimolecular reactions. We focus on electronic motion and show, with HD+ as an example, that one can find non-stationary states where the electron (with some probability...

  6. Optimization and control of electron beams from laser wakefield accelerations using asymmetric laser pulses

    Science.gov (United States)

    Gopal, K.; Gupta, D. N.

    2017-10-01

    Optimization and control of electron beam quality in laser wakefield acceleration are explored by using a temporally asymmetric laser pulse of the sharp rising front portion. The temporally asymmetric laser pulse imparts stronger ponderomotive force on the ambient plasma electrons. The stronger ponderomotive force associated with the asymmetric pulse significantly affects the injection of electrons into the wakefield and consequently the quality of the injected bunch in terms of injected charge, mean energy, and emittance. Based on particle-in-cell simulations, we report to generate a monoenergetic electron beam with reduced emittance and enhanced charge in laser wakefield acceleration using an asymmetric pulse of duration 30 fs.

  7. Two-pulse laser control of bond-selective fragmentation

    DEFF Research Database (Denmark)

    Amstrup, Bjarne; Henriksen, Niels Engholm

    1996-01-01

    We elaborate on a two-pulse (pump-pump) laser control scheme for selective bond-breaking in molecules [Amstrup and Henriksen, J. Chem. Phys. 97, 8285 (1992)]. We show, in particular, that with this scheme one can overcome the obstacle of intramolecular vibrational relaxation. As an example, we...

  8. Design of optimal laser pulses to control molecular rovibrational ...

    Indian Academy of Sciences (India)

    Abstract. Optimal control theory in combination with time-dependent quantum dynamics is employed to design laser pulses which can perform selective vibrational and rotational excitations in a heteronuclear diatomic system. We have applied the conjugate gradient method for the constrained optimization of a suit-.

  9. Design of optimal laser pulses to control molecular rovibrational ...

    Indian Academy of Sciences (India)

    Optimal control theory in combination with time-dependent quantum dynamics is employed to design laser pulses which can perform selective vibrational and rotational excitations in a heteronuclear diatomic system. We have applied the conjugate gradient method for the constrained optimization of a suitably designed ...

  10. Free Electron Laser Pulse Control by Acousto Optic Modulators

    CERN Document Server

    Kanai, T; Yoshihashi-Suzuki, S

    2005-01-01

    Free Electron Laser (FEL) at Osaka University can be continuously varied in the range of 5.0-20.0 μm. A FEL has a double pulse structure. The structure consists of a train of macropulses of the pulse width 15 μs, and each macropulse contains a train of 330 micropulses of the pulse width 5 ps. The tunability and short pulse afford new medical applications such as investigation of protein dynamics and ablation of soft tissues. Precise control of micropulse train is very important for medical applications using FEL because macropulse with long pulse duration sometimes leads to undesirable thermal effects. FEL pulse control system using an acousto optic modulators (AOM) was developed in order to investigate of non-thermal effect between the FEL and tissue. This system provide a very good efficiency (~60 %) and a fast switching speed (>200 ns). A phosphorylated protein was irradiated with FEL that controlled the pulse. These result confirmed that the thermal effect is controlled by pulse durat...

  11. Two-pulse laser control for selective photofragment orientation

    DEFF Research Database (Denmark)

    Machholm, Mette; Henriksen, Niels Engholm

    1999-01-01

    The nuclear wave packet dynamics in the potential well of a bound molecule can be controlled by an intense infrared (IR)-laser pulse. The phase of the nuclear wave packet motion is shown to depend on the phase of the laser field and the initial orientation of the molecule. We demonstrate......, for diatomic heteronuclear molecules, that these spatial effects can be used to control the angular distribution of photofragments by selective dissociation of molecules with a given initial orientation from a sample of randomly oriented molecules. (C) 1999 American Institute of Physics. [S0021-9606(99)01131-9]....

  12. Controlling laser-ion acceleration with chirped pulses

    Science.gov (United States)

    Mackenroth, Felix; Gonoskov, Arkady; Marklund, Mattias

    2017-10-01

    The recently proposed novel laser-ion acceleration scheme Chirped-standing-wave acceleration (CSWA) makes use of chirped high-intensity laser pulses to gain enhanced control over the accelerated ions' phase space distribution. The first proof-of-principle analysis of this scheme promised favorable scaling properties of ion energies and densities while simultaneously offering unprecedented spatial and temporal control over the ion beam itself. In this talk we provide an extended analysis of the schemes' further capabilities accessible through, e.g., customized laser chirps and targets. We provide quantitative estimates for existing and upcoming experimental facilities to highlight the scheme's versatility. Furthermore, we benchmark the newly proposed scheme against conventional laser-ion acceleration schemes. To this end we use the accelerated ions' flux as a measure for the conversion efficiency of laser energy into ion kinetic energy and provide a systematic comparison of the theoretically achievable performances of the most common laser-ion acceleration schemes. We find CSWA to be highly competitive in terms of reachable ion energies and fluxes.

  13. Free-electron-laser-induced shock-wave control and mechanistic analysis using pulse control.

    Science.gov (United States)

    Kanai, Taizo; Yoshihashi-Suzuki, Sachiko; Awazu, Kunio

    2008-11-01

    The wavelength of the free electron laser (FEL) in Osaka University can be continuously varied in the range of 5.0-20.0 microm. The FEL has a double-pulse structure, consisting of a train of macropulses of pulse duration 12 micros. Each macropulse contains a train of 330 micropulses of pulse duration 5 ps. The tunability and picosecond pulses afford new medical and biological applications. However, a macropulse of long pulse duration leads to undesirable secondary effects. Precise control of the macropulse duration is essential for the high-precision applications of the FEL. An FEL pulse control system using acousto-optic modulators has been developed to investigate mechanical (shock-wave) effects of the FEL on living tissues. With this system, we have controlled photoinduced shock waves and determine the mechanism of interaction during FEL-induced tissue ablation.

  14. First-principles electron dynamics control simulation of diamond under femtosecond laser pulse train irradiation.

    Science.gov (United States)

    Wang, Cong; Jiang, Lan; Wang, Feng; Li, Xin; Yuan, Yanping; Xiao, Hai; Tsai, Hai-Lung; Lu, Yongfeng

    2012-07-11

    A real-time and real-space time-dependent density functional is applied to simulate the nonlinear electron-photon interactions during shaped femtosecond laser pulse train ablation of diamond. Effects of the key pulse train parameters such as the pulse separation, spatial/temporal pulse energy distribution and pulse number per train on the electron excitation and energy absorption are discussed. The calculations show that photon-electron interactions and transient localized electron dynamics can be controlled including photon absorption, electron excitation, electron density, and free electron distribution by the ultrafast laser pulse train.

  15. Noncollinear SHG with compensation of phase mismatch by controlling frequency chirp and tilted pulse fronts of femtosecond laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Aoyama, Makoto; Nakano, Fumihiko; Akahane, Yutaka; Yamakawa, Koichi [Japan Atomic Energy Research Inst., Kizu, Kyoto (Japan). Kansai Research Establishment; Harimoto, Tetsuo [Yamanashi Univ., Faculty of Engineering, Yamanashi (Japan)

    2001-10-01

    In order to achieve efficient second-harmonic generation with femtosecond laser pulses, we studied noncollinear second-harmonic generation with tilted pulse fronts and a suitable frequency chirp of fundamental pulses. We discussed the compensation of a phase-mismatch by controlling the frequency chirp of fundamental pulses and an improvement of the energy conversion efficiency using our method. When the energy conversion efficiency was less than 0.4% under a phase-mismatch condition, we experimentally obtained a 30% energy conversion efficiency with a proper frequency chirp of fundamental pulses. (author)

  16. Externally Controlled Injection of Electrons by a Laser Pulse in a Laser Wakefield Electron Accelerator

    CERN Document Server

    Chen Szu Yuan; Chen Wei Ting; Chien, Ting-Yei; Lee, Chau-Hwang; Lin, Jiunn-Yuan; Wang, Jyhpyng

    2005-01-01

    Spatially and temporally localized injection of electrons is a key element for development of plasma-wave electron accelerator. Here we report the demonstration of two different schemes for electron injection in a self-modulated laser wakefield accelerator (SM-LWFA) by using a laser pulse. In the first scheme, by implementing a copropagating laser prepulse with proper timing, we are able to control the growth of Raman forward scattering and the production of accelerated electrons. We found that the stimulated Raman backward scattering of the prepulse plays the essential role of injecting hot electrons into the fast plasma wave driven by the pump pulse. In the second scheme, by using a transient density ramp we achieve self-injection of electrons in a SM-LWFA with spatial localization. The transient density ramp is produced by a prepulse propagating transversely to drill a density depression channel via ionization and expansion. The same mechanism of injection with comparable efficiency is also demonstrated wi...

  17. Nanofabrication with Pulsed Lasers

    Directory of Open Access Journals (Sweden)

    Kabashin AV

    2010-01-01

    Full Text Available Abstract An overview of pulsed laser-assisted methods for nanofabrication, which are currently developed in our Institute (LP3, is presented. The methods compass a variety of possibilities for material nanostructuring offered by laser–matter interactions and imply either the nanostructuring of the laser-illuminated surface itself, as in cases of direct laser ablation or laser plasma-assisted treatment of semiconductors to form light-absorbing and light-emitting nano-architectures, as well as periodic nanoarrays, or laser-assisted production of nanoclusters and their controlled growth in gaseous or liquid medium to form nanostructured films or colloidal nanoparticles. Nanomaterials synthesized by laser-assisted methods have a variety of unique properties, not reproducible by any other route, and are of importance for photovoltaics, optoelectronics, biological sensing, imaging and therapeutics.

  18. A pulsed single-longitudinal-mode fiber laser based on gain control of pulse-injection-locked cavity

    Science.gov (United States)

    Wan, Hongdan; Wu, Zhongwei; Sun, Xiaohan

    2013-06-01

    We achieve a pulsed fiber laser based on injecting a pulsed-seed into a high power fiber ring cavity consisting of two-stage amplifier chain. Through gain control of the fiber amplifier chain and adjustment of a variable optical coupler in the cavity, locking condition is satisfied which produce mode-hopping free, single-longitudinal-mode optical spectrum with 38 dB optical signal to noise ratio. The noise-free lasing RF spectrum has a 7.0 kHz 3 dB linewidth. The nanosecond lasing pulses are jittering-free with 40 W peak power at 1550 nm wavelength.

  19. Electron injection and emittance control by transverse colliding pulses in a laser-plasma accelerator

    Directory of Open Access Journals (Sweden)

    M. Chen

    2014-05-01

    Full Text Available A method to inject electron beams with controllable transverse emittances in a laser-plasma accelerators is proposed and analyzed. It uses two colliding laser pulses that propagate transversely to the plasma wave. For colliding pulses with equal frequencies, a beam with very low emittance is generated when the collision is close to the density peak of the plasma wave. Electrons near the axis are accelerated longitudinally by the ponderomotive force of the colliding pulses, accelerated transversely by the beat wave, and subsequently injected into the second bucket of the wake. Ionization is used to increase the transverse injection area and the final trapped charge. Simulations show that the transverse emittance can be less than the 0.1 mm mrad level, which is important for many applications. For colliding laser pulses with different frequencies, the beat wave can produce asymmetric injection, which can enhance betatron radiation generated by the electron beam.

  20. Hydrodynamic size distribution of gold nanoparticles controlled by repetition rate during pulsed laser ablation in water

    Science.gov (United States)

    Menéndez-Manjón, Ana; Barcikowski, Stephan

    2011-02-01

    Most investigations on the laser generation and fragmentation of nanoparticles focus on Feret particle size, although the hydrodynamic size of nanoparticles is of great importance, for example in biotechnology for diffusion in living cells, or in engineering, for a tuned rheology of suspensions. In this sense, the formation and fragmentation of gold colloidal nanoparticles using femtosecond laser ablation at variable pulse repetition rates (100-5000 Hz) in deionized water were investigated through their plasmon resonance and hydrodynamic diameter, measured by Dynamic Light Scattering. The increment of the repetition rate does not influence the ablation efficiency, but produces a decrease of the hydrodynamic diameter and blue-shift of the plasmon resonance of the generated gold nanoparticles. Fragmentation, induced by inter-pulse irradiation of the colloids was measured online, showing to be more effective low repetition rates. The pulse repetition rate is shown to be an appropriate laser parameter for hydrodynamic size control of nanoparticles without further influence on the production efficiency.

  1. Dynamic control of laser driven proton beams by exploiting self-generated, ultrashort electromagnetic pulses

    Energy Technology Data Exchange (ETDEWEB)

    Kar, S., E-mail: s.kar@qub.ac.uk; Ahmed, H.; Nersisyan, G.; Hanton, F.; Naughton, K.; Lewis, C. L. S.; Borghesi, M. [Centre for Plasma Physics, School of Mathematics and Physics, Queen' s University Belfast, Belfast BT7 1NN (United Kingdom); Brauckmann, S.; Giesecke, A. L.; Willi, O. [Institut für Laser-und Plasmaphysik, Heinrich-Heine-Universität, Düsseldorf (Germany)

    2016-05-15

    As part of the ultrafast charge dynamics initiated by high intensity laser irradiations of solid targets, high amplitude EM pulses propagate away from the interaction point and are transported along any stalks and wires attached to the target. The propagation of these high amplitude pulses along a thin wire connected to a laser irradiated target was diagnosed via the proton radiography technique, measuring a pulse duration of ∼20 ps and a pulse velocity close to the speed of light. The strong electric field associated with the EM pulse can be exploited for controlling dynamically the proton beams produced from a laser-driven source. Chromatic divergence control of broadband laser driven protons (upto 75% reduction in divergence of >5 MeV protons) was obtained by winding the supporting wire around the proton beam axis to create a helical coil structure. In addition to providing focussing and energy selection, the technique has the potential to post-accelerate the transiting protons by the longitudinal component of the curved electric field lines produced by the helical coil lens.

  2. Phase-only laser control in the weak-field limit: Two-pulse control of IBr photofragmentation revisited

    DEFF Research Database (Denmark)

    Tiwari, Ashwani Kumar; Henriksen, Niels Engholm

    2016-01-01

    We demonstrate theoretically that laser-induced coherent quantum interference control of asymptotic states of dissociating molecules is possible, starting from a single vibrational eigenstate, after the interaction with two laser pulses-at a fixed time delay-both operating in the weak-field limit...

  3. Controlled modification of biomolecules by ultrashort laser pulses in polar liquids

    DEFF Research Database (Denmark)

    Gruzdev, Vitaly; Korkin, Dmitry; Mooney, Brian P.

    2017-01-01

    to a small class of photosensitive biomolecules because of strong and ultrafast perturbations from biomolecule-solvent interactions. Here, we report excitation of harmonics of vibration modes of solvent molecules by femtosecond laser pulses to produce controlled chemical modifications of non...

  4. Phase and Frequency Control of Laser Arrays for Pulse Synthesis

    Science.gov (United States)

    2015-01-02

    M. Fukuda, M. Okayasu, J. Temmyo, and J. Nakano, “Degradation behavior of 0.98-µm strained quantum well InGaAs /AlGaAs lasers under high-power...from traditional quantum well lasers remains difficult however due to the onset of limiting effects such as two-photon absorption, gain saturation...in Passively Mode Locked GaAs/AlGaAs Quantum Well Lasers,” IEEE J. of Quant. Elec. 48(3), 318-327 (2012). 2. A. Schmitt-Sody, A. Velten, Y. Liu, L

  5. Ultrashort Laser Pulse Phenomena

    CERN Document Server

    Diels, Jean-Claude

    2006-01-01

    Ultrashort Laser Pulse Phenomena, 2e serves as an introduction to the phenomena of ultra short laser pulses and describes how this technology can be used to examine problems in areas such as electromagnetism, optics, and quantum mechanics. Ultrashort Laser Pulse Phenomena combines theoretical backgrounds and experimental techniques and will serve as a manual on designing and constructing femtosecond (""faster than electronics"") systems or experiments from scratch. Beyond the simple optical system, the various sources of ultrashort pulses are presented, again with emphasis on the basic

  6. Control of optical properties of hybrid materials with chirped femtosecond laser pulses under strong coupling conditions.

    Science.gov (United States)

    Sukharev, Maxim

    2014-08-28

    The interaction of chirped femtosecond laser pulses with hybrid materials--materials comprised of plasmon sustaining structures and resonant molecules--is scrutinized using a self-consistent model of coupled Maxwell-Bloch equations. The optical properties of such systems are examined with the example of periodic sinusoidal gratings. It is shown that under strong coupling conditions one can control light transmission using chirped pulses in a spatiotemporal manner. The temporal origin of control relies on chirps non-symmetric in time while the space control is achieved via spatial localization of electromagnetic energy due to plasmon resonances.

  7. Controlled injection and acceleration of electrons in plasma wakefields by colliding laser pulses.

    Science.gov (United States)

    Faure, J; Rechatin, C; Norlin, A; Lifschitz, A; Glinec, Y; Malka, V

    2006-12-07

    In laser-plasma-based accelerators, an intense laser pulse drives a large electric field (the wakefield) which accelerates particles to high energies in distances much shorter than in conventional accelerators. These high acceleration gradients, of a few hundreds of gigavolts per metre, hold the promise of compact high-energy particle accelerators. Recently, several experiments have shown that laser-plasma accelerators can produce high-quality electron beams, with quasi-monoenergetic energy distributions at the 100 MeV level. However, these beams do not have the stability and reproducibility that are required for applications. This is because the mechanism responsible for injecting electrons into the wakefield is based on highly nonlinear phenomena, and is therefore hard to control. Here we demonstrate that the injection and subsequent acceleration of electrons can be controlled by using a second laser pulse. The collision of the two laser pulses provides a pre-acceleration stage which provokes the injection of electrons into the wakefield. The experimental results show that the electron beams obtained in this manner are collimated (5 mrad divergence), monoenergetic (with energy spread electron bunch durations shorter than 10 fs. We anticipate that this stable and compact electron source will have a strong impact on applications requiring short bunches, such as the femtolysis of water, or high stability, such as radiotherapy with high-energy electrons or radiography for materials science.

  8. Field-programmable gate array-controlled sweep velocity-locked laser pulse generator

    Science.gov (United States)

    Chen, Zhen; Hefferman, Gerald; Wei, Tao

    2017-05-01

    A field-programmable gate array (FPGA)-controlled sweep velocity-locked laser pulse generator (SV-LLPG) design based on an all-digital phase-locked loop (ADPLL) is proposed. A distributed feedback laser with modulated injection current was used as a swept-frequency laser source. An open-loop predistortion modulation waveform was calibrated using a feedback iteration method to initially improve frequency sweep linearity. An ADPLL control system was then implemented using an FPGA to lock the output of a Mach-Zehnder interferometer that was directly proportional to laser sweep velocity to an on-board system clock. Using this system, linearly chirped laser pulses with a sweep bandwidth of 111.16 GHz were demonstrated. Further testing evaluating the sensing utility of the system was conducted. In this test, the SV-LLPG served as the swept laser source of an optical frequency-domain reflectometry system used to interrogate a subterahertz range fiber structure (sub-THz-FS) array. A static strain test was then conducted and linear sensor results were observed.

  9. Robust two-level system control by a detuned and chirped laser pulse

    Science.gov (United States)

    Jo, Hanlae; Lee, Han-gyeol; Guérin, Stéphane; Ahn, Jaewook

    2017-09-01

    We propose and demonstrate a robust control scheme by an ultrafast nonadiabatic chirped laser pulse, designed for targeting coherent superpositions of two-level systems. Robustness against power fluctuation is proved by our numerical study and a proof-of-principle experiment performed with femtosecond laser interaction on cold atoms. They exhibit for the final driven dynamics a cusp on the Bloch sphere, corresponding to a zero curvature of fidelity. This solution is particularly simple and thus applicable to a wide range of potential applications.

  10. Hot electron production in laser solid interactions with a controlled pre-pulse

    Energy Technology Data Exchange (ETDEWEB)

    Culfa, O.; Tallents, G. J.; Wagenaars, E.; Ridgers, C. P.; Dance, R. J.; Rossall, A. K.; Woolsey, N. C. [York Plasma Institute, Department of Physics, The University of York, York YO10 5DD (United Kingdom); Gray, R. J.; McKenna, P. [Department of Physics, SUPA, University of Strathclyde, Glasgow G4 0NG (United Kingdom); Brown, C. D. R.; James, S. F.; Hoarty, D. J. [AWE, Aldermaston, Reading, Berkshire RG7 4PR (United Kingdom); Booth, N.; Robinson, A. P. L. [CLF, STFC Rutherford Appleton Laboratory, Didcot, Oxfordshire OX11 0QX (United Kingdom); Lancaster, K. L. [York Plasma Institute, Department of Physics, The University of York, York YO10 5DD (United Kingdom); CLF, STFC Rutherford Appleton Laboratory, Didcot, Oxfordshire OX11 0QX (United Kingdom); Pikuz, S. A. [Joint Institute for High Temperatures, Russian Academy of Sciences, Moscow 125412 (Russian Federation); Faenov, A. Ya. [Joint Institute for High Temperatures, Russian Academy of Sciences, Moscow 125412 (Russian Federation); Quantum Beam Science Directorate, Japan Atomic Energy Agency, Kizugawa, Kyoto 619-0215 (Japan); Kampfer, T.; Schulze, K. S.; Uschmann, I. [Friedrich Schiller University of Jena, D-07743 Jena (Germany)

    2014-04-15

    Hot electron generation plays an important role in the fast ignition approach to inertial confinement fusion (ICF) and other applications with ultra-intense lasers. Hot electrons of temperature up to 10–20 MeV have been produced by high contrast picosecond duration laser pulses focussed to intensities of ∼10{sup 20} W cm{sup −2} with a deliberate pre-pulse on solid targets using the Vulcan Petawatt Laser facility. We present measurements of the number and temperature of hot electrons obtained using an electron spectrometer. The results are correlated to the density scale length of the plasma produced by a controlled pre-pulse measured using an optical probe diagnostic. 1D simulations predict electron temperature variations with plasma density scale length in agreement with the experiment at shorter plasma scale lengths (<7.5μm), but with the experimental temperatures (13–17 MeV) dropping below the simulation values (20–25 MeV) at longer scale lengths. The experimental results show that longer interaction plasmas produced by pre-pulses enable significantly greater number of hot electrons to be produced.

  11. Controlling magnetism by ultrashort laser pulses: from fundamentals to nanoscale engineering

    Science.gov (United States)

    Bossini, D.; Rasing, Th.

    2016-06-01

    From the discovery of sub-picosecond demagnetization over a decade ago [1] to the recent demonstration of magnetization reversal by a single 40 femtosecond laser pulse [2], the manipulation of spins by ultra-short laser pulses has become a fundamentally challenging topic with a potentially high impact for future spintronics, data storage and manipulation and quantum computation [3]. It was realized that the femtosecond laser induced all-optical switching (AOS) as observed in ferrimagnets exploits the laser induced strongly non-equilibrium dynamics and the antiferromagnetic exchange interaction between their sublattices [4-6]. This opens the way to engineer new magnetic materials for AOS [7,8], though for real applications nanoscale control of inhomogeneities appears to be relevant [9]. Besides the intruiging technological implications of these observations, they broadened remarkably the frontiers of our fundamental knowledge of magnetic phenomena. The laser driven out-of-equilibrium states cannot be described in term of the well-established thermodynamical approach, which is based on the concepts of equilibrium and adiabatic transformations. Theoretical efforts, although in their infancy, have already demonstrated [5,6] that light-induced spin dynamics on the (sub)-picosecond time scale results in phenomena utterly forbidden in a thermodynamical framework. Another challenge is how to bring the optical manipulation of magnetic media to the required nanoscale. This is clearly a key element for the perspectives in terms of magnetic recording. In addition, it would allow to explore a novel regime of spin dynamics, since the investigation of magnets on the femtosecond time-scale and the nanometer length-scale simultaneously is unexplored. One experimental approach which may be successful makes use of wave-shaping techniques [10]. Recent results with engineered hybrid magnetic materials and nanofocusing via a plasmonic antenna showed the practical potential of AOS: the

  12. Control of HOD photodissociation dynamics via bond-selective infrared multiphoton excitation and a femtosecond ultraviolet laser pulse

    DEFF Research Database (Denmark)

    Amstrup, Bjarne; Henriksen, Niels Engholm

    1992-01-01

    A scheme for controlling the outcome of a photodissociation process is studied. It involves two lasers—one intense laser in the infrared region which is supposed to excite a particular bond in the electronic ground state, and a second short laser pulse in the ultraviolet region which, at the righ...

  13. Automatic quality control in the production of ceramic substrates by pulsed laser cutting

    DEFF Research Database (Denmark)

    Morace, Renate Erica; Hansen, Hans Nørgaard; De Chiffre, Leonardo

    2004-01-01

    This paper deals with the use of optical coordinate measuring machines (CMMs) in the quality control of ceramic substrates produced by a CO2 pulsed laser. A procedure of automatic measurements on a CMM equipped with a CCD camera was developed. In particular, the number and the distribution...... of cavities on the cut face of thin ceramic substrates were investigated and different strategies to assess the depth and the pitch of cavities were compared. Then, the measurement uncertainty for these two critical parameters was evaluated using the method described in ISO/TS 15530-3....

  14. Controlling the porosity of collagen, gelatin and elastin biomaterials by ultrashort laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Daskalova, A., E-mail: a_daskalova@code.bg [Institute of Electronics, Bulgarian Academy of Sciences, 72, Tsarigradsko Chaussee blvd., 1784 Sofia (Bulgaria); Nathala, Chandra S.R. [IAP, Vienna University of Technology, Wiedner Hauptstrasse 8-10, 1040 Vienna (Austria); Femtolasers Productions GmbH, Fernkorngasse10, 1100 Vienna (Austria); Bliznakova, I. [Institute of Electronics, Bulgarian Academy of Sciences, 72, Tsarigradsko Chaussee blvd., 1784 Sofia (Bulgaria); Stoyanova, E. [IBIR, Department of Molecular Immunology, Bulgarian Academy of Sciences, 73, Tzarigradsko Chaussee blvd., 1113 Sofia (Bulgaria); Zhelyazkova, A. [Institute of Electronics, Bulgarian Academy of Sciences, 72, Tsarigradsko Chaussee blvd., 1784 Sofia (Bulgaria); Ganz, T. [Femtolasers Productions GmbH, Fernkorngasse10, 1100 Vienna (Austria); Lueftenegger, S.; Husinsky, W. [IAP, Vienna University of Technology, Wiedner Hauptstrasse 8-10, 1040 Vienna (Austria)

    2014-02-15

    We report on the structural investigation of self-organized micropores generated in thin gelatin, collagen, and collagen–elastin films after single and multishot irradiation with pulse durations ranging from 30–100 fs at 800 nm. We systematically studied the effect of laser parameters: laser energy, number of pulses, and pulse duration on the development of the micropores. This work showed that applying laser pulses at different rates significantly modified the thin film surface. The results clearly revealed that femtosecond laser treatment of thin films of biomaterials: gelatin, collagen and collagen–elastin, results in creation of micro/nanopores with different size of cavity formations. Experimentally, it is demonstrated that it is possible to influence the dimensions of the pore sizes, ranging from 100 nm to 2 μm by tuning the laser parameters. We are currently further exploring the possibility of structuring these biomaterials by applying a time delay between separate pulses. First results from cell culture experiments on laser created surface foam of collagen–elastin were successfully obtained, showing the potential of the method to cultivate cells on superficial porous substrates and the preferable selectivity of the cells to proliferate on the laser modified parts of the biopolymer substrate.

  15. Long-pulsed dye laser versus long-pulsed dye laser-assisted photodynamic therapy for acne vulgaris: A randomized controlled trial

    DEFF Research Database (Denmark)

    Haedersdal, M.; Togsverd, K.; Wiegell, S.R.

    2008-01-01

    Background: Long-pulsed dye laser (LPDL)-assisted photodynamic therapy has been suggested to be superior to laser alone for acne vulgaris but no evidence is available. Objective: To evaluate the efficacy and safety of LPDL alone versus LPDL in photodynamic therapy with methylaminolevulinic acid (...

  16. Laser plasma acceleration with a negatively chirped pulse: all-optical control over dark current in the blowout regime

    Science.gov (United States)

    Kalmykov, S. Y.; Beck, A.; Davoine, X.; Lefebvre, E.; Shadwick, B. A.

    2012-03-01

    Recent experiments with 100 terawatt-class, sub-50 femtosecond laser pulses show that electrons self-injected into a laser-driven electron density bubble can be accelerated above 0.5 gigaelectronvolt energy in a sub-centimetre-length rarefied plasma. To reach this energy range, electrons must ultimately outrun the bubble and exit the accelerating phase; this, however, does not ensure high beam quality. Wake excitation increases the laser pulse bandwidth by red-shifting its head, keeping the tail unshifted. Anomalous group velocity dispersion of radiation in plasma slows down the red-shifted head, compressing the pulse into a few-cycle-long piston of relativistic intensity. Pulse transformation into a piston causes continuous expansion of the bubble, trapping copious numbers of unwanted electrons (dark current) and producing a poorly collimated, polychromatic energy tail, completely dominating the electron spectrum at the dephasing limit. The process of piston formation can be mitigated by using a broad-bandwidth (corresponding to a few-cycle transform-limited duration), negatively chirped pulse. Initial blue-shift of the pulse leading edge compensates for the nonlinear frequency red-shift and delays the piston formation, thus significantly suppressing the dark current, making the leading quasi-monoenergetic bunch the dominant feature of the electron spectrum near dephasing. This method of dark current control may be feasible for future experiments with ultrahigh-bandwidth, multi-joule laser pulses.

  17. Ultrashort pulse lasers applied to propulsion/control in space- and atmospheric-flight

    Science.gov (United States)

    Kremeyer, Kevin

    2008-05-01

    An impulse measurement device and analysis package was conceived, designed, constructed, tested, and demonstrated to be capable of: measuring nanoNewton-seconds to milliNewton-seconds of impulse due to laser-ablation; being transported as carry-on baggage; set-up and tear-down times of less than an hour; target exchange times of less than two minutes (targets can be ablated at multiple positions for thousands of shots); measurements in air and in vacuum; error of just a few percent; repeatability over a wide range of potential systematic error sources; and time between measurements, including ring-down and analysis, of less than 30 seconds. The instrument consists of a cantilever (i.e. leaf spring), whose time-dependent displacement/oscillation is measured and analyzed to determine the impulse imparted by a laser pulse to a target. These shapes are readily/commercially available, and any target material can be used, provided it can be fashioned in the form of a cantilever, or as a coating/film/tape, suitable for mounting on a cantilever of known geometry. The instrument was calibrated both statically and dynamically, and measurements were performed on brass, steel, and Aluminum, using laser pulses of ~7ns, ~500ps, and ~500fs. The results agree well with those published in the literature, with surface effects, atmosphere, and pre-/post-pulses demonstrating interesting effects and indicating areas for further study. In addition to exploring space-propulsion applications, measurements were performed to explore the strong beneficial effects of depositing lines of energy ahead of supersonic and hypersonic vehicles. This deposition creates a low-density channel, through which a vehicle can travel with dramatically reduced drag. Temperature and pressure are both also reduced on the front surfaces of the vehicle, while density and pressure are increased at the vehicle base. When applied off-center, this technique can be used to control the vehicle, employing the entire

  18. Pulsed-laser printing of silver nanoparticles ink: control of morphological properties.

    Science.gov (United States)

    Rapp, Ludovic; Ailuno, Julie; Alloncle, Anne Patricia; Delaporte, Philippe

    2011-10-24

    Fine electrically-conductive patterns of silver nanoparticles ink have been laser printed using the laser-induced forward transfer (LIFT) technique. LIFT is a technique that offers the possibility of printing patterns with high spatial resolution from a wide range of materials in solid or liquid state. Influence of drying the ink film, previous to its transfer, on the printed droplet morphology is discussed. The laser pulse energy and donor-receiver substrate separation were systematically varied and their effects on the transferred droplets were analyzed. The use of an intermediate titanium dynamic release layer was also investigated and demonstrated the possibility of a better control of both the size and shape of the printed patterns. Conditions have been determined for printing flat-top droplets with sharp edges. 21 µm width silver lines with 80 nm thickness have been printed with a smooth convex profile. Electrical resistivities of the transferred patterns are only 5 times higher than the bulk silver. © 2011 Optical Society of America

  19. Laser pulse shaping for optimal control of multiphoton dissociation in a diatomic molecule using genetic algorithm optimization

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Sitansh, E-mail: sitansh@research.iiit.ac.in [Center for Computational Natural Sciences and Bioinformatics, International Institute of Information Technology, Hyderabad 500 032 (India); Singh, Harjinder, E-mail: harjinder.singh@iiit.ac.in [Center for Computational Natural Sciences and Bioinformatics, International Institute of Information Technology, Hyderabad 500 032 (India)

    2011-11-18

    Graphical abstract: Application of genetic algorithm optimization to control dissociation process in the ground electronic state of HF molecule is demonstrated. Highlights: Black-Right-Pointing-Pointer Genetic algorithm optimization for the design of laser pulses. Black-Right-Pointing-Pointer Control of dissociation process in the ground electronic state of HF molecule. Black-Right-Pointing-Pointer Two types of pulses, one with fixed frequency components and the other having non-deterministic components. Black-Right-Pointing-Pointer Optimized laser fields possess simple time and frequency structures. - Abstract: We have applied genetic algorithm optimization for the design of laser pulses to control dissociation process in the ground electronic state of HF molecule, within the mathematical framework of optimal control theory. In order to design the experimentally feasible laser fields, we coded the small set of selected field parameters in the GA parameter space. Two types of pulses, one with fixed frequency components and the other having non-deterministic components have been designed. Optimized laser field obtained using this approach, possesses simple time and frequency structures. We show that the fields having non-deterministic frequency components lead to greater dissociation probability compared to the ones having deterministic frequency components.

  20. Femtosecond Laser Pulses Principles and Experiments

    CERN Document Server

    Rullière, Claude

    2005-01-01

    This smooth introduction for advanced undergraduates starts with the fundamentals of lasers and pulsed optics. Thus prepared, the student is introduced to short and ultrashort laser pulses, and learns how to generate, manipulate, and measure them. Spectroscopic implications are also discussed. The second edition has been completely revised and includes two new chapters on some of the most promising and fast-developing applications in ultrafast phenomena: coherent control and attosecond pulses.

  1. Controlled assembly of high-order nanoarray metal structures on bulk copper surface by femtosecond laser pulses

    Science.gov (United States)

    Qin, Wanwan; Yang, Jianjun

    2017-07-01

    We report a new one-step maskless method to fabricate high-order nanoarray metal structures comprising periodic grooves and particle chains on a single-crystal Cu surface using femtosecond laser pulses at the central wavelength of 400 nm. Remarkably, when a circularly polarized infrared femtosecond laser pulse (spectrally centered at 800 nm) pre-irradiates the sample surface, the geometric dimensions of the composite structure can be well controlled. With increasing the energy fluence of the infrared laser pulse, both the groove width and particle diameter are observed to reduce, while the measured spacing-to-diameter ratio of the nanoparticles tends to present an increasing tendency. A physical scenario is proposed to elucidate the underlying mechanisms: as the infrared femtosecond laser pulse pre-irradiates the target, the copper surface is triggered to display anomalous transient physical properties, on which the subsequently incident Gaussian blue laser pulse is spatially modulated into fringe-like energy depositions via the excitation of ultrafast surface plasmon. During the following relaxation processes, the periodically heated thin-layer regions can be transferred into the metastable liquid rivulets and then they break up into nanodroplet arrays owing to the modified Rayleigh-like instability. This investigation indicates a simple integrated approach for active designing and large-scale assembly of complexed functional nanostructures on bulk materials.

  2. Fabrication, size control and functionalization of silver nanoparticles by pulsed laser ablation synthesis in liquid

    Science.gov (United States)

    Baranov, M. S.; Khramov, V. N.; Lotin, A. A.; Khaydukov, E. V.

    2017-03-01

    Functionalized nanoparticles are important analytical tool for biomedical applications. Pulsed laser ablation of bulk targets in an aqueous media is the one-step method for the fabrication, size manipulation and biofunctionalization of nanoparticles. We performed kHz laser ablation of a silver target by nanosecond pulses in tetramethylammonium hydroxide (TMAH) and sodium dodecyl sulfate (SDS) aqueous solutions to prepare silver nanoparticles. It was shown that the formation efficiency was increased by addition of TMAH and SDS as well as the stability of nanoparticles. The size decrease of the nanoparticles by addition of SDS was more remarkable than in the laser ablation in TMAH aqueous solutions. Emitted nanoparticles interact with TMAH and SDS in the secondary laser irradiation process leads to the nanoparticles stabilization in aqueous solutions.

  3. Optimal control of laser plasma instabilities using Spike Trains of Uneven Duration and Delay (STUD pulses for ICF and IFE

    Directory of Open Access Journals (Sweden)

    Afeyan Bedros

    2013-11-01

    Full Text Available An adaptive method of controlling parametric instabilities in laser produced plasmas is proposed. It involves fast temporal modulation of a laser pulse on the fastest instability's amplification time scale, adapting to changing and unknown plasma conditions. These pulses are comprised of on and off sequences having at least one or two orders of magnitude contrast between them. Such laser illumination profiles are called STUD pulses for Spike Trains of Uneven Duration and Delay. The STUD pulse program includes scrambling the speckle patterns spatially in between the laser spikes. The off times allow damping of driven waves. The scrambling of the hot spots allows tens of damping times to elapse before hot spot locations experience recurring high intensity spikes. Damping in the meantime will have healed the scars of past growth. Another unique feature of STUD pulses on crossing beams is that their temporal profiles can be interlaced or staggered, and their interactions thus controlled with an on-off switch and a dimmer.

  4. Coherent control of bond making: The performance of rationally phase-shaped femtosecond laser pulses

    CERN Document Server

    Levin, Liat; Kosloff, Ronnie; Koch, Christiane P; Amitay, Zohar

    2015-01-01

    The first step in the coherent control of a photoinduced binary reaction is bond making or photoassociation. We have recently demonstrated coherent control of bond making in multi-photon femtosecond photoassociation of hot magnesium atoms, using linearly chirped pulses [Levin et al., arXiv:1411.1542]. The detected yield of photoassociated magnesium dimers was enhanced by positively chirped pulses which is explained theoretically by a combination of purification and chirp-dependent Raman transitions. The yield could be further enhanced by pulse optimization resulting in pulses with an effective linear chirp and a sub-pulse structure, where the latter allows for exploiting vibrational coherences. Here, we systematically explore the efficiency of phase-shaped pulses for the coherent control of bond making, employing a parametrization of the spectral phases in the form of cosine functions. We find up to an order of magnitude enhancement of the yield compared to the unshaped transform-limited pulse. The highly per...

  5. Pulse width shaping of passively mode-locked soliton fiber laser via polarization control in carbon nanotube saturable absorber.

    Science.gov (United States)

    Jeong, Hwanseong; Choi, Sun Young; Rotermund, Fabian; Yeom, Dong-Il

    2013-11-04

    We report the continuous control of the pulse width of a passively mode-locked fiber laser via polarization state adjustment in a single-walled carbon nanotube saturable absorber (SWCNT-SA). The SWCNT, coated on the side-polished fiber, was fabricated with optimized conditions and used for stable mode-locking of the fiber laser without Q-switching instabilities for any polarization state of the laser intra-cavity. The 3-dB spectral bandwidth of the mode-locked pulses can be continuously tuned from 1.8 nm to 8.5 nm with the polarization control for a given laser cavity length and applied pump power. A pulse duration varying from 470 fs to 1.6 ps was also observed with a change in the spectral bandwidth. The linear and the nonlinear transmission properties of the SA were analyzed, and found to exhibit different modulation depths depending on the input polarization state in the SA. The largest modulation depth of the SA was observed at the polarization state of the transverse electric mode that delivers shortest pulses at the laser output.

  6. Pulsed laser ablation of copper

    Science.gov (United States)

    Jordan, R.; Cole, D.; Lunney, J. G.; Mackay, K.; Givord, D.

    1995-02-01

    The laser ablation of copper with a 532 nm, 6 ns laser has been investigated in the regime normally used for pulsed laser deposition. The ablation depth per pulse and the flux and energy distribution of the ions in the plume were measured and compared to the deposition rate as measured by a quartz microbalance. These measurements were compared with an analytic model of ablation via a laser sustained plasma. It is shown that self-sputtering of the growing film is significant.

  7. Laser Pulses Characterization with Pyroelectric Sensors

    OpenAIRE

    Malka, V.; J. Faure; Y. Gauduel

    2010-01-01

    There are many industrial and medical applications of CO2 (λ=10.6 μm) and Nd:YAG (λ=1.06 μm) infrared lasers for which the quality of the process are tightly connected to the characteristic of the laser pulse. These two types of lasers deliver pulses with duration, repetition frequency and power that can be controlled by means of a programmable electronic control unit. An open-loop control generally optimize the process performances by availing of a laser system model. How...

  8. Coherent scatter-controlled phase-change grating structures in silicon using femtosecond laser pulses.

    Science.gov (United States)

    Fuentes-Edfuf, Yasser; Garcia-Lechuga, Mario; Puerto, Daniel; Florian, Camilo; Garcia-Leis, Adianez; Sanchez-Cortes, Santiago; Solis, Javier; Siegel, Jan

    2017-07-04

    Periodic structures of alternating amorphous-crystalline fringes have been fabricated in silicon using repetitive femtosecond laser exposure (800 nm wavelength and 120 fs duration). The method is based on the interference of the incident laser light with far- and near-field scattered light, leading to local melting at the interference maxima, as demonstrated by femtosecond microscopy. Exploiting this strategy, lines of highly regular amorphous fringes can be written. The fringes have been characterized in detail using optical microscopy combined modelling, which enables a determination of the three-dimensional shape of individual fringes. 2D micro-Raman spectroscopy reveals that the space between amorphous fringes remains crystalline. We demonstrate that the fringe period can be tuned over a range of 410 nm - 13 µm by changing the angle of incidence and inverting the beam scan direction. Fine control over the lateral dimensions, thickness, surface depression and optical contrast of the fringes is obtained via adjustment of pulse number, fluence and spot size. Large-area, highly homogeneous gratings composed of amorphous fringes with micrometer width and millimeter length can readily be fabricated. The here presented fabrication technique is expected to have applications in the fields of optics, nanoelectronics, and mechatronics and should be applicable to other materials.

  9. Controlling the rotation of asymmetric top molecules by the combination of a long and a short laser pulse

    DEFF Research Database (Denmark)

    Viftrup, Simon S.; Kumarappan, Vinod; Holmegaard, Lotte

    2009-01-01

    We describe theoretically and experimentally a laser-based method to    control the rotations of asymmetric top molecules in three-dimensional    space. Our method relies on keeping one axis of a molecule essentially    fixed in space along the polarization vector of a nanosecond laser    pulse (...... (termed the long pulse) and forcing the molecule to rotate about    the aligned axis by an orthogonally polarized, femtosecond laser pulse    (termed the short pulse). Experimentally, we use femtosecond timed    Coulomb explosion to image the three-dimensional (3D) alignment of the    3...... the role    played by the intensity of the long and the short laser pulses. To    illustrate the generality of our method, we illustrate its    applicability to a molecule (3,4-dibromothiophene), with significantly    different inertia and polarizability tensors. Finally, our theory shows...

  10. High power ultrashort pulse lasers

    Energy Technology Data Exchange (ETDEWEB)

    Perry, M.D.

    1994-10-07

    Small scale terawatt and soon even petawatt (1000 terawatt) class laser systems are made possible by application of the chirped-pulse amplification technique to solid-state lasers combined with the availability of broad bandwidth materials. These lasers make possible a new class of high gradient accelerators based on the large electric fields associated with intense laser-plasma interactions or from the intense laser field directly. Here, we concentrate on the laser technology to produce these intense pulses. Application of the smallest of these systems to the production of high brightness electron sources is also introduced.

  11. Laser system using ultra-short laser pulses

    Science.gov (United States)

    Dantus, Marcos [Okemos, MI; Lozovoy, Vadim V [Okemos, MI; Comstock, Matthew [Milford, MI

    2009-10-27

    A laser system using ultrashort laser pulses is provided. In another aspect of the present invention, the system includes a laser, pulse shaper and detection device. A further aspect of the present invention employs a femtosecond laser and binary pulse shaping (BPS). Still another aspect of the present invention uses a laser beam pulse, a pulse shaper and a SHG crystal.

  12. Phase-only shaped laser pulses in optimal control theory: Application to indirect photofragmentation dynamics in the weak-field limit

    DEFF Research Database (Denmark)

    Shu, Chuan-Cun; Henriksen, Niels E.

    2012-01-01

    We implement phase-only shaped laser pulses within quantum optimal control theory for laser-molecule interaction. This approach is applied to the indirect photofragmentation dynamics of NaI in the weak-field limit. It is shown that optimized phase-modulated pulses with a fixed frequency distribut...

  13. Controlling residual hydrogen gas in mass spectra during pulsed laser atom probe tomography.

    Science.gov (United States)

    Kolli, R Prakash

    2017-01-01

    Residual hydrogen (H2) gas in the analysis chamber of an atom probe instrument limits the ability to measure H concentration in metals and alloys. Measuring H concentration would permit quantification of important physical phenomena, such as hydrogen embrittlement, corrosion, hydrogen trapping, and grain boundary segregation. Increased insight into the behavior of residual H2 gas on the specimen tip surface in atom probe instruments could help reduce these limitations. The influence of user-selected experimental parameters on the field adsorption and desorption of residual H2 gas on nominally pure copper (Cu) was studied during ultraviolet pulsed laser atom probe tomography. The results indicate that the total residual hydrogen concentration, HTOT, in the mass spectra exhibits a generally decreasing trend with increasing laser pulse energy and increasing laser pulse frequency. Second-order interaction effects are also important. The pulse energy has the greatest influence on the quantity HTOT, which is consistently less than 0.1 at.% at a value of 80 pJ.

  14. Optical pulses, lasers, measuring techniques

    CERN Document Server

    Früngel, Frank B A

    1965-01-01

    High Speed Pulse Technology: Volume II: Optical Pulses - Lasers - Measuring Techniques focuses on the theoretical and engineering problems that result from the capacitor discharge technique.This book is organized into three main topics: light flash production from a capacitive energy storage; signal transmission and ranging systems by capacitor discharges and lasers; and impulse measuring technique. This text specifically discusses the air spark under atmospheric conditions, industrial equipment for laser flashing, and claims for light transmitting system. The application of light impulse sign

  15. Characterization of handpieces to control tissue ablation with pulsed CO2 laser

    Science.gov (United States)

    Verdaasdonck, Rudolf M.; van Swol, Christiaan F. P.; Coates, Judith

    1995-05-01

    Focusing handpieces used for CO2 beam delivery allow large variation of the power density in the spot depending on the distance to the tissue and hence the effect on the tissue. In contrast to the cw CO2 laser, the pulsed CO2 laser vaporized tissue water instantly (: equals ablation threshold), leaving a charless crater in the tissue surface. Only if the fluence is below or near threshold, the tissue effects are comparable with the cw laser. The threshold and tissue effects were studied for focusing (f equals 119 mm) and collimating (3 mm) handpieces coupled to an ultrapulsed CO2 laser. Using a special thermal imaging setup based on Schlieren techniques, the ablation threshold was determined depending on spotsize and pulse energy (1-200 mJ). In the focus of the handpiece, the threshold was already exceeded at 1 mJ, creating holes that were larger than the theoretical expected spotsize. The ablation threshold (J/cm2) increased for larger spotsizes. Below threshold, there is heating of the tissue resulting in coagulation. Above threshold, the exploding water vapor consumed thermal energy suppressing heating of the surrounding tissue. The gaussian shape of the collimated beam results in relatively more thermal effects. Focusing handpieces provide a wide range in power density and thus require experience from the surgeon. Collimated handpieces might be more easy to handle but offer less flexibility in tissue effect and a larger thermal zone.

  16. Genetic algorithm-based control of birefringent filtering for self-tuning, self-pulsing fiber lasers

    Science.gov (United States)

    Woodward, R. I.; Kelleher, E. J. R.

    2017-08-01

    Polarization-based filtering in fiber lasers is well-known to enable spectral tunability and a wide range of dynamical operating states. This effect is rarely exploited in practical systems, however, because optimization of cavity parameters is non-trivial and evolves due to environmental sensitivity. Here, we report a genetic algorithm-based approach, utilizing electronic control of the cavity transfer function, to autonomously achieve broad wavelength tuning and the generation of Q-switched pulses with variable repetition rate and duration. The practicalities and limitations of simultaneous spectral and temporal self-tuning from a simple fiber laser are discussed, paving the way to on-demand laser properties through algorithmic control and machine learning schemes.

  17. Pulsed Scophony laser projection system

    Science.gov (United States)

    Lowry, J. B.; Welford, W. T.; Humphries, M. R.

    1988-10-01

    A novel laser TV projection display has been developed by PA Technology employing the Scophony system with acousto-optic modulators and pulsed lasers. This results in a projection system with greater optical simplicity, higher reliability and reduced power and cooling requirements over similar laser projectors. The technique has been successfully implemented in British Aerospace's Microdome missile training simulator. This paper describes the underlying principles of the design, its operational features and its implementation in the Microdome.

  18. Apparatus to control and visualize the impact of a high-energy laser pulse on a liquid target

    Science.gov (United States)

    Klein, Alexander L.; Lohse, Detlef; Versluis, Michel; Gelderblom, Hanneke

    2017-09-01

    We present an experimental apparatus to control and visualize the response of a liquid target to a laser-induced vaporization. We use a millimeter-sized drop as target and present two liquid-dye solutions that allow a variation of the absorption coefficient of the laser light in the drop by seven orders of magnitude. The excitation source is a Q-switched Nd:YAG laser at its frequency-doubled wavelength emitting nanosecond pulses with energy densities above the local vaporization threshold. The absorption of the laser energy leads to a large-scale liquid motion at time scales that are separated by several orders of magnitude, which we spatiotemporally resolve by a combination of ultra-high-speed and stroboscopic high-resolution imaging in two orthogonal views. Surprisingly, the large-scale liquid motion upon laser impact is completely controlled by the spatial energy distribution obtained by a precise beam-shaping technique. The apparatus demonstrates the potential for accurate and quantitative studies of laser-matter interactions.

  19. Laser-pulse-shape control of photofragmentation in the weak-field limit

    DEFF Research Database (Denmark)

    Tiwari, Ashwani Kumar; Dey, Diptesh; Henriksen, Niels Engholm

    2014-01-01

    We demonstrate theoretically that laser-induced coherent quantum interference control of asymptotic states of dissociating molecules is possible even in the (one-photon) weak-field limit starting from a single vibrational eigenstate. Thus, phase dependence in the interaction with a fixed energy...

  20. Flexible control of femtosecond pulse duration and separation using an emittance-spoiling foil in x-ray free-electron lasers

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Y. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Behrens, C. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Coffee, R. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Decker, F. -J. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Emma, P. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Field, C. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Helml, W. [Technische Univ. Munchen, Garching (Germany); Huang, Z. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Krejcik, P. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Krzywinski, J. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Loos, H. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Lutman, A. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Marinelli, A. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Maxwell, T. J. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Turner, J. [SLAC National Accelerator Lab., Menlo Park, CA (United States)

    2015-06-22

    We report experimental studies of generating and controlling femtosecond x-ray pulses in free-electron lasers (FELs) using an emittance spoiling foil. By selectivity spoiling the transverse emittance of the electron beam, the output pulse duration or double-pulse separation is adjusted with a variable size single or double slotted foil. Measurements were performed with an X-band transverse deflector located downstream of the FEL undulator, from which both the FEL lasing and emittance spoiling effects are observed directly.

  1. Optimisation study of the synthesis of vanadium oxide nanostructures using pulsed laser deposition

    CSIR Research Space (South Africa)

    Masina, BN

    2014-02-01

    Full Text Available . For the case of the nanosecond, long pulse laser ablation, the plasma expands isothermally during the laser pulse followed by adiabatic expansion after the laser pulse termination [7, 8]. During the isothermal regime process, initially the laser interacts... and plasma plume expansion during a pulsed laser deposition process of synthesising the VO2 nanostructures thin films. In pulsed laser deposition (PLD) process, it is important to control the plume dynamics in order to obtain good quality and correct...

  2. Synchronization of picosecond laser pulses to the target X-ray pulses at SPring-8

    CERN Document Server

    Tanaka, Y; Kitamura, H; Ishikawa, T

    2001-01-01

    Synchronization system between an intense picosecond laser and the target X-ray pulses has been developed at SPring-8. The intense laser pulses were obtained by amplification of the pulses picked up from a mode-locked Ti:sapphire laser synchronized with the radio frequency of the storage ring. The repetition rate of amplified laser pulses was controlled to be 1/n of the RF, where n is a multiple of the number of RF buckets in the ring, so that the laser pulses meet the SR pulses originated from a particular electron bunch in partial filling patterns. The temporal overlap of the laser and the target X-ray pulses was achieved as monitored with a streak camera in synchroscan and repetitive single shot operation modes, and was stable with a precision of a few ps for several hours.

  3. Pulsed Laser Annealing of Carbon

    Science.gov (United States)

    Abrahamson, Joseph P.

    This dissertation investigates laser heating of carbon materials. The carbon industry has been annealing carbon via traditional furnace heating since at least 1800, when Sir Humphry Davy produced an electric arc with carbon electrodes made from carbonized wood. Much knowledge has been accumulated about carbon since then and carbon materials have become instrumental both scientifically and technologically. However, to this day the kinetics of annealing are not known due to the slow heating and cooling rates of furnaces. Additionally, consensus has yet to be reached on the cause of nongraphitizability. Annealing trajectories with respect to time at temperature are observed from a commercial carbon black (R250), model graphitizable carbon (anthracene coke) and a model nongraphitizable carbon (sucrose char) via rapid laser heating. Materials were heated with 1064 nm and 10.6 im laser radiation from a Q-switched Nd:YAG laser and a continuous wave CO2 laser, respectively. A pulse generator was used reduce the CO2 laser pulse width and provide high temporal control. Time-temperature-histories with nanosecond temporal resolution and temperature reproducibility within tens of degrees Celsius were determined by spectrally resolving the laser induced incandescence signal and applying multiwavelength pyrometry. The Nd:YAG laser fluences include: 25, 50, 100, 200, 300, and 550 mJ/cm2. The maximum observed temperature ranged from 2,400 °C to the C2 sublimation temperature of 4,180 °C. The CO2 laser was used to collect a series of isothermal (1,200 and 2,600 °C) heat treatments versus time (100 milliseconds to 30 seconds). Laser heated samples are compared to furnace annealing at 1,200 and 2,600 °C for 1 hour. The material transformation trajectory of Nd:YAG laser heated carbon is different than traditional furnace heating. The traditional furnace annealing pathway is followed for CO2 laser heating as based upon equivalent end structures. The nanostructure of sucrose char

  4. Long-pulsed Nd:YAG laser vs. intense pulsed light for hair removal in dark skin: a randomized controlled trial.

    Science.gov (United States)

    Ismail, S A

    2012-02-01

    Although several lasers meet the wavelength criteria for selective follicular destruction, the treatment of darker skin phototypes is particularly challenging because absorption of laser energy by the targeted hairs is compromised by an increased concentration of epidermal melanin. To compare satisfaction level, safety and effectiveness of a long-pulsed Nd:YAG laser and intense pulsed light (IPL) in axillary hair reduction in subjects with dark skin. The study design was a within-patient, right-left, assessor-blinded, comparison of long-pulsed Nd:YAG laser and IPL. Fifty women (skin phototypes IV-VI) volunteered for removal of axillary hair. Five sessions at 4- to 6-week intervals were performed. Hair counts at both sides were compared at baseline and 6months after the last session. Final overall evaluations were performed by subjects and clinician at the end of the study. Satisfaction was scored for both devices. Thirty-nine women completed the study. At 6months, the decrease in hair counts on the laser side (79·4%, PIPL side (54·4%, P<0·01 vs. pretreatment). Only temporary adverse effects were reported at both sides. Higher pain scores and more inflammation were reported with Nd:YAG laser; however, it was preferred by 29 volunteers (74%). Volunteers reported higher satisfaction score with Nd:YAG laser (P<0·01). Dark skin can be treated by both systems safely and effectively; however, long-pulsed (1064 nm) Nd:YAG laser is more effective as reported by both subjects and clinician. © 2011 The Authors. BJD © 2011 British Association of Dermatologists.

  5. Pulse-burst operation of standard Nd:YAG lasers

    Energy Technology Data Exchange (ETDEWEB)

    Den Hartog, D J; Borchardt, M T; Reusch, J A; Yang, Y M [Department of Physics, University of Wisconsin-Madison, Madison, Wisconsin 53706 (United States); Ambuel, J R; Robl, P E, E-mail: djdenhar@wisc.ed [Physical Sciences Laboratory, University of Wisconsin-Madison, Stoughton, Wisconsin 53589 (United States)

    2010-05-01

    Two standard commercial flashlamp-pumped Nd:YAG lasers have been upgraded to 'pulse-burst' capability. Each laser produces a burst of up to fifteen 2 J Q-switched pulses (1064 nm) at repetition rates 1-12.5 kHz. Variable pulse-width drive (0.15-0.39 ms) of the flashlamps is accomplished by IGBT (insulated gate bipolar transistor) switching of electrolytic capacitor banks. Direct control of the laser Pockels cell drive enables optimal pulse energy extraction, and up to four 2 J laser pulses during one flashlamp pulse. These lasers are used in the Thomson scattering plasma diagnostic system on the MST reversed-field pinch to study the dynamic evolution of the electron temperature.

  6. Selective laser melting of copper using ultrashort laser pulses

    Science.gov (United States)

    Kaden, Lisa; Matthäus, Gabor; Ullsperger, Tobias; Engelhardt, Hannes; Rettenmayr, Markus; Tünnermann, Andreas; Nolte, Stefan

    2017-09-01

    Within the field of laser-assisted additive manufacturing, the application of ultrashort pulse lasers for selective laser melting came into focus recently. In contrast to conventional lasers, these systems provide extremely high peak power at ultrashort interaction times and offer the potential to control the thermal impact at the vicinity of the processed region by tailoring the pulse repetition rate. Consequently, materials with extremely high melting points such as tungsten or special composites such as AlSi40 can be processed. In this paper, we present the selective laser melting of copper using 500 fs laser pulses at MHz repetition rates emitted at a center wavelength of about 1030 nm. To identify an appropriate processing window, a detailed parameter study was performed. We demonstrate the fabrication of bulk copper parts as well as the realization of thin-wall structures featuring thicknesses below 100 {μ }m. With respect to the extraordinary high thermal conductivity of copper which in general prevents the additive manufacturing of elements with micrometer resolution, this work demonstrates the potential for sophisticated copper products that can be applied in a wide field of applications extending from microelectronics functionality to complex cooling structures.

  7. Ultrashort Laser Pulses in Biology and Medicine

    CERN Document Server

    Braun, Markus; Zinth, Wolfgang

    2008-01-01

    Sources of ultrashort laser pulses are nowadays commercially available and have entered many areas of research and development. This book gives an overview of biological and medical applications of these laser pulses. The briefness of these laser pulses permits the tracing of the fastest processes in photo-active bio-systems, which is one focus of the book. The other focus is applications that rely on the high peak intensity of ultrashort laser pulses. Examples covered span non-linear imaging techniques, optical tomography, and laser surgery.

  8. Pulsed laser deposition: metal versus oxide ablation

    NARCIS (Netherlands)

    Doeswijk, L.M.; Rijnders, Augustinus J.H.M.; Blank, David H.A.

    2004-01-01

    We present experimental results of pulsed laser interaction with metal (Ni, Fe, Nb) and oxide (TiO2, SrTiO3, BaTiO3) targets. The influence of the laser fluence and the number of laser pulses on the resulting target morphology are discussed. Although different responses for metal and oxide targets

  9. CTS and CZTS for solar cells made by pulsed laser deposition and pulsed electron deposition

    DEFF Research Database (Denmark)

    Ettlinger, Rebecca Bolt

    This thesis concerns the deposition of thin films for solar cells using pulsed laser deposition (PLD) and pulsed electron deposition (PED). The aim was to deposit copper tin sulfide (CTS) and zinc sulfide (ZnS) by pulsed laser deposition to learn about these materials in relation to copper zinc tin......, which make them promising alternatives to the commercially successful solar cell material copper indium gallium diselenide (CIGS). Complementing our group's work on pulsed laser deposition of CZTS, we collaborated with IMEM-CNR in Parma, Italy, to deposit CZTS by pulsed electron deposition for the first...... of using pulsed electron deposition was to make CZTS at a low processing temperature, avoiding the 570 °C annealing step used for our pulsed laser deposited solar cells. Preliminary solar cells had an efficiency of 0.2 % with a 300 °C deposition step without annealing. Further process control is needed...

  10. CO{sub 2} laser pulse shortening by laser ablation of a metal target

    Energy Technology Data Exchange (ETDEWEB)

    Donnelly, T.; Mazoyer, M.; Lynch, A.; O' Sullivan, G.; O' Reilly, F.; Dunne, P.; Cummins, T. [School of Physics, University College Dublin, Belfield, Dublin 4 (Ireland)

    2012-03-15

    A repeatable and flexible technique for pulse shortening of laser pulses has been applied to transversely excited atmospheric (TEA) CO{sub 2} laser pulses. The technique involves focusing the laser output onto a highly reflective metal target so that plasma is formed, which then operates as a shutter due to strong laser absorption and scattering. Precise control of the focused laser intensity allows for timing of the shutter so that different temporal portions of the pulse can be reflected from the target surface before plasma formation occurs. This type of shutter enables one to reduce the pulse duration down to {approx}2 ns and to remove the low power, long duration tails that are present in TEA CO{sub 2} pulses. The transmitted energy is reduced as the pulse duration is decreased but the reflected power is {approx}10 MW for all pulse durations. A simple laser heating model verifies that the pulse shortening depends directly on the plasma formation time, which in turn is dependent on the applied laser intensity. It is envisaged that this plasma shutter will be used as a tool for pulse shaping in the search for laser pulse conditions to optimize conversion efficiency from laser energy to useable extreme ultraviolet (EUV) radiation for EUV source development.

  11. Pulsed Laser Spectroscopy: An Inexpensive Approach

    Science.gov (United States)

    Daly, J. G.; Hastings, R.; Schmidt, J. A.

    1982-10-01

    The assembly of a pulsed laser spectroscopy laboratory is presented. The authors describe how they constructed pulsed lasers, fast photodetectors, a boxcar signal averager, and associated equipment. A molecular nitrogen laser operating up to 50 Hz with an ultraviolet (337.1 nm) 700 kW pulse was used to optically pump an organic dye laser. The resulting output could be tuned from 360.0 to 680.0 nm. This pulse was typically 30 kW and 8 nsec, which makes it ideally suited to selective excitation and fluorescence studies. By constructing this equipment, it is estimated that the investment was one-tenth the cost of commercial components.

  12. Matrix assisted pulsed laser evaporation of pullulan tailor-made biomaterial thin films for controlled drug delivery systems

    Energy Technology Data Exchange (ETDEWEB)

    Cristescu, R [National Institute for Laser, Plasma and Radiation Physics, MG-36, RO-77125, Bucharest (Romania); Jelinek, M [Institute of Physics ASCR, Na Slovance 2, 182 21Prague 8 (Czech Republic); Kocourek, T [Institute of Physics ASCR, Na Slovance 2, 182 21Prague 8 (Czech Republic); Axente, E [National Institute for Laser, Plasma and Radiation Physics, MG-36, RO-77125, Bucharest (Romania); Grigorescu, S [National Institute for Laser, Plasma and Radiation Physics, MG-36, RO-77125, Bucharest (Romania); Moldovan, A [National Institute for Laser, Plasma and Radiation Physics, MG-36, RO-77125, Bucharest (Romania); Mihaiescu, D E [University of Agriculture Sciences and Veterinary Medicine, 59 Marasti, Bucharest (Romania); Albulescu, M [National Institute for Chemical-Pharmaceutical R and D, 112 Vitan, 74373 Bucharest 3 (Romania); Buruiana, T [Petru Poni Institute of Macromolecular Chemistry, Iasi, 6600 (Romania); Dybal, J [Institute of Macromolecular Chemistry, Academy of Sciences of the Czech Republic, Heyrovsky Sq. 2, 16206, Prague 6, Czech Republic (Czech Republic); Stamatin, I [University of Bucharest, Faculty of Physics, PO Box MG-11, 3Nano-SAE Research Center, Bucharest-Magurele (Romania); Mihailescu, I N [National Institute for Laser, Plasma and Radiation Physics, MG-36, RO-77125, Bucharest (Romania); Chrisey, D B [Naval Research Laboratory, Code 6851 Washington, DC 20375 (United States)

    2007-04-15

    We report the first successful deposition of cinnamate-pullulan polysaccharide thin films by Matrix Assisted Pulsed Laser Evaporation (MAPLE). Thin film depositions were performed in vacuum using a KrF* excimer laser source ({lambda} = 248 nm, {tau} {approx} 20 ns) operated at a repetition rate of 10 Hz. The dependence on incident laser fluence of the induced surface morphology is studied. We demonstrated by Raman spectroscopy that our MAPLE-deposited cinnamate-pullulan thin films are composed of starting materials preserving their chemical structures, with no impurities.

  13. Generation And Measurement Of High Contrast Ultrashort Intense Laser Pulses

    CERN Document Server

    Konoplev, O A

    2000-01-01

    In this thesis, the generation and measurement of high contrast, intense, ultrashort pulses have been studied. Various factors affecting the contrast and pulse shape of ultrashort light pulses from a chirped pulse amplification (CPA) laser system are identified. The level of contrast resulting from influence of these factors is estimated. Methods for improving and controlling the pulse shape and increasing the contrast are discussed. Ultrahigh contrast, 1-ps pulses were generated from a CPA system with no temporal structure up to eleven orders of magnitude. This is eight orders of magnitude higher contrast than the original pulse. This contrast boost was achieved using two techniques. One is the optical pulse cleaning based on the nonlinear birefringence of the chirping fiber and applied to the pulses before amplification. The other is the fast saturable absorber. The fast saturable absorber was placed after amplification and compression of the pulse. The measurements of high-contrast, ultrashort pulse with h...

  14. Formation of the active medium in high-power repetitively pulsed gas lasers pumped by an electron-beam-controlled discharge

    Science.gov (United States)

    Bulaev, V. D.; Lysenko, S. L.

    2015-07-01

    A high-power repetitively pulsed e-beam-controlled discharge CO2 laser is simulated numerically; the simulation results are compared with experimental data. Optimal sizes and design of electrodes and configuration of the external magnetic field are found, which allow one to introduce no less than 90% electric pump energy into a specified volume of the active medium, including the active volume of a laser with an aperture of 110 × 110 cm. The results obtained can also be used to design other types of highpower gas lasers.

  15. Ultrashort pulse laser technology laser sources and applications

    CERN Document Server

    Schrempel, Frank; Dausinger, Friedrich

    2016-01-01

    Ultrashort laser pulses with durations in the femtosecond range up to a few picoseconds provide a unique method for precise materials processing or medical applications. Paired with the recent developments in ultrashort pulse lasers, this technology is finding its way into various application fields. The book gives a comprehensive overview of the principles and applications of ultrashort pulse lasers, especially applied to medicine and production technology. Recent advances in laser technology are discussed in detail. This covers the development of reliable and cheap low power laser sources as well as high average power ultrashort pulse lasers for large scale manufacturing. The fundamentals of laser-matter-interaction as well as processing strategies and the required system technology are discussed for these laser sources with respect to precise materials processing. Finally, different applications within medicine, measurement technology or materials processing are highlighted.

  16. One laser pulse generates two photoacoustic signals

    CERN Document Server

    Gao, Fei; Zheng, Yuanjin

    2016-01-01

    Photoacoustic sensing and imaging techniques have been studied widely to explore optical absorption contrast based on nanosecond laser illumination. In this paper, we report a long laser pulse induced dual photoacoustic (LDPA) nonlinear effect, which originates from unsatisfied stress and thermal confinements. Being different from conventional short laser pulse illumination, the proposed method utilizes a long square-profile laser pulse to induce dual photoacoustic signals. Without satisfying the stress confinement, the dual photoacoustic signals are generated following the positive and negative edges of the long laser pulse. More interestingly, the first expansion-induced photoacoustic signal exhibits positive waveform due to the initial sharp rising of temperature. On the contrary, the second contraction-induced photoacoustic signal exhibits exactly negative waveform due to the falling of temperature, as well as pulse-width-dependent, signal amplitude which is caused by the concurrent heat accumulation and ...

  17. Short-pulse laser interactions with disordered materials and liquids

    Energy Technology Data Exchange (ETDEWEB)

    Phinney, L.M.; Goldman, C.H.; Longtin, J.P.; Tien, C.L. [Univ. of California, Berkeley, CA (United States)

    1995-12-31

    High-power, short-pulse lasers in the picosecond and subpicosecond range are utilized in an increasing number of technologies, including materials processing and diagnostics, micro-electronics and devices, and medicine. In these applications, the short-pulse radiation interacts with a wide range of media encompassing disordered materials and liquids. Examples of disordered materials include porous media, polymers, organic tissues, and amorphous forms of silicon, silicon nitride, and silicon dioxide. In order to accurately model, efficiently control, and optimize short-pulse, laser-material interactions, a thorough understanding of the energy transport mechanisms is necessary. Thus, fractals and percolation theory are used to analyze the anomalous diffusion regime in random media. In liquids, the thermal aspects of saturable and multiphoton absorption are examined. Finally, a novel application of short-pulse laser radiation to reduce surface adhesion forces in microstructures through short-pulse laser-induced water desorption is presented.

  18. Dark pulse quantum dot diode laser.

    Science.gov (United States)

    Feng, Mingming; Silverman, Kevin L; Mirin, Richard P; Cundiff, Steven T

    2010-06-21

    We describe an operating regime for passively mode-locked quantum dot diode laser where the output consists of a train of dark pulses, i.e., intensity dips on a continuous background. We show that a dark pulse train is a solution to the master equation for mode-locked lasers. Using simulations, we study stability of the dark pulses and show they are consistent with the experimental results.

  19. Combinatorial Matrix Assisted Pulsed Laser Evaporation of a biodegradable polymer and fibronectin for protein immobilization and controlled release

    Energy Technology Data Exchange (ETDEWEB)

    Sima, F., E-mail: felix.sima@inflpr.ro [Lasers Department, National Institute for Lasers, Plasma and Radiation Physics, Măgurele (Romania); Axente, E.; Iordache, I.; Luculescu, C. [Lasers Department, National Institute for Lasers, Plasma and Radiation Physics, Măgurele (Romania); Gallet, O. [ERRMECE, Cergy-Pontoise University, Cergy-Pontoise (France); Anselme, K. [IS2M, CNRS UMR7361, Haute-Alsace University, Mulhouse (France); Mihailescu, I.N. [Lasers Department, National Institute for Lasers, Plasma and Radiation Physics, Măgurele (Romania)

    2014-07-01

    Defined protein quantities were embedded in situ in a biodegradable polymer coating during simultaneous laser vaporization of two targets. Fibronectin (FN) and poly-DL-lactide (PDLLA) were transferred and immobilized concomitantly by Combinatorial Matrix Assisted Pulsed Laser Evaporation onto solid substrates. The film surface with gradient of composition was characterized by optical, scanning electron microscopy and profilometry. Micrometric FN packages were visualized in the polymeric matrix by confocal microscopy. The composition of FN was investigated by FTIR and μFTIR analyses in a polymeric matrix with different thickness.

  20. Initial state-specific photodissociation dynamics of pyrrole via 1 π σ ∗/ S 0 conical intersection initiated with optimally controlled UV-laser pulses

    Science.gov (United States)

    Nandipati, K. R.; Kanakati, Arun Kumar; Singh, H.; Lan, Z.; Mahapatra, S.

    2017-09-01

    Optimal initiation of quantum dynamics of N-H photodissociation of pyrrole on the S0-1πσ∗(1A2) coupled electronic states by UV-laser pulses in an effort to guide the subsequent dynamics to dissociation limits is studied theoretically. Specifically, the task of designing optimal laser pulses that act on initial vibrational states of the system for an effective UV-photodissociation is considered by employing optimal control theory. The associated control mechanism(s) for the initial state dependent photodissociation dynamics of pyrrole in the presence of control pulses is examined and discussed in detail. The initial conditions determine implicitly the variation in the dissociation probabilities for the two channels, upon interaction with the field. The optimal pulse corresponds to the objective fixed as maximization of overall reactive flux subject to constraints of reasonable fluence and quantum dynamics. The simple optimal pulses obtained by the use of genetic algorithm based optimization are worth an experimental implementation given the experimental relevance of πσ∗-photochemistry in recent times.

  1. Femtosecond laser pulses principles and experiments

    CERN Document Server

    1998-01-01

    This smooth introduction for advanced undergraduate students starts with the fundamentals of lasers and pulsed optics Thus prepared, the student learns how to generate short and ultrashort laser pulses, how to manipulate them, and how to measure them Finally, spectroscopic implications are discussed This rounded text gives the student an up-to-date introduction to one of the most exciting fields in laser physics

  2. Pulse-burst laser systems for fast Thomson scattering (invited)

    Energy Technology Data Exchange (ETDEWEB)

    Den Hartog, D. J. [Department of Physics, University of Wisconsin-Madison, 1150 University Avenue, Madison, Wisconsin 53706 (United States); Center for Magnetic Self-Organization in Laboratory and Astrophysical Plasmas, University of Wisconsin-Madison, Madison, Wisconsin 53706 (United States); Ambuel, J. R.; Holly, D. J.; Robl, P. E. [Physical Sciences Laboratory, University of Wisconsin-Madison, 3725 Schneider Drive, Stoughton, Wisconsin 53589 (United States); Borchardt, M. T.; Falkowski, A. F.; Harris, W. S.; Parke, E.; Reusch, J. A.; Stephens, H. D.; Yang, Y. M. [Department of Physics, University of Wisconsin-Madison, 1150 University Avenue, Madison, Wisconsin 53706 (United States)

    2010-10-15

    Two standard commercial flashlamp-pumped Nd:YAG (YAG denotes yttrium aluminum garnet) lasers have been upgraded to ''pulse-burst'' capability. Each laser produces a burst of up to 15 2 J Q-switched pulses (1064 nm) at repetition rates of 1-12.5 kHz. Variable pulse-width drive (0.15-0.39 ms) of the flashlamps is accomplished by insulated gate bipolar transistor (IGBT) switching of electrolytic capacitor banks. Direct control of the laser Pockels cell drive enables optimal pulse energy extraction, and up to four 2 J laser pulses during one flashlamp pulse. These lasers are used in the Thomson scattering plasma diagnostic system on the MST reversed-field pinch to record the dynamic evolution of the electron temperature profile and temperature fluctuations. To further these investigations, a custom pulse-burst laser system with a maximum pulse repetition rate of 250 kHz is now being commissioned.

  3. Effect of pulsed Nd:YAG laser in the treatment of neuropathic foot ulcers in children with spina bifida: a randomized controlled study.

    Science.gov (United States)

    Ebid, Anwar Abdelgayed; El-Kafy, Ehab Mohame Abd; Alayat, Mohamed Salaheldien Mohamed

    2013-12-01

    This study assessed the effects of pulsed Nd:YAG laser treatment of neuropathic foot ulcers in children with spina bifida. Children with spina bifida face increased risk for developing neuropathic foot ulcers. In a randomized controlled trial, 39 children and adolescents (ages 6-15 years) with spina bifida and stage III neuropathic foot ulcers were randomly assigned to the laser group or the placebo laser group. The former received pulsed Nd:YAG laser treatments (i.e., total energy of 300-350 J during three sessions/week) plus standard wound care, and the latter received sham laser treatments plus standard wound care. Wound size and wound appearance were assessed for all patients at the beginning of the treatment, after 5 weeks, and after 10 weeks. The decrease in wound surface area at 5 and 10 weeks post- treatment was significantly greater in the laser group (i.e., 2.44 ± 0.33 and 0.29 ± 0.25 cm(2), respectively) than in the placebo group (i.e., 3.81 ± 0.18 and 3.24 ± 0.44 cm(2), respectively). Also, the decrease in the total score for the Pressure Sore Status Tool (PSST) at 5 and 10 weeks post-treatment was significantly different for the laser group (i.e., 32.76 ± 2.30 and 17.52 ± 1.66, respectively) than for the placebo group (i.e., 46.50 ± 2.12 and 38.11 ± 3.17, respectively). Treatment with pulsed neodymium:yttrium aluminum garnet (Nd:YAG) laser combined with standard wound care decreases wound size and improves wound appearance for stage III neuropathic foot ulcers in children with spina bifida.

  4. Short pulse laser systems for biomedical applications

    CERN Document Server

    Mitra, Kunal

    2017-01-01

    This book presents practical information on the clinical applications of short pulse laser systems and the techniques for optimizing these applications in a manner that will be relevant to a broad audience, including engineering and medical students as well as researchers, clinicians, and technicians. Short pulse laser systems are useful for both subsurface tissue imaging and laser induced thermal therapy (LITT), which hold great promise in cancer diagnostics and treatment. Such laser systems may be used alone or in combination with optically active nanoparticles specifically administered to the tissues of interest for enhanced contrast in imaging and precise heating during LITT. Mathematical and computational models of short pulse laser-tissue interactions that consider the transient radiative transport equation coupled with a bio-heat equation considering the initial transients of laser heating were developed to analyze the laser-tissue interaction during imaging and therapy. Experiments were first performe...

  5. Pulse number controlled laser annealing for GeSn on insulator structure with high substitutional Sn concentration

    Energy Technology Data Exchange (ETDEWEB)

    Moto, Kenta; Sadoh, Taizoh; Miyao, Masanobu, E-mail: miyao@ed.kyushu-u.ac.jp [Department of Electronics, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Matsumura, Ryo [Department of Electronics, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); JSPS, 5-3-1 Kojimachi, Chiyoda-ku, Tokyo 102-0083 (Japan); Ikenoue, Hiroshi [Department of Gigaphoton Next GLP, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan)

    2016-06-27

    Crystalline GeSn-on-insulator structures with high Sn concentration (>8%), which exceeds thermal equilibrium solid-solubility (∼2%) of Sn in Ge, are essential to achieve high-speed thin film transistors and high-efficiency optical devices. We investigate non-thermal equilibrium growth of Ge{sub 1−x}Sn{sub x} (0 ≤ x ≤ 0.2) on quartz substrates by using pulsed laser annealing (PLA). The window of laser fluence enabling complete crystallization without film ablation is drastically expanded (∼5 times) by Sn doping above 5% into Ge. Substitutional Sn concentration in grown layers is found to be increased with decreasing irradiation pulse number. This phenomenon can be explained on the basis of significant thermal non-equilibrium growth achieved by higher cooling rate after PLA with a lower pulse number. As a result, GeSn crystals with substitutional Sn concentration of ∼12% are realized at pulse irradiation of single shot for the samples with the initial Sn concentration of 15%. Raman spectroscopy and electron microscopy measurements reveal the high quality of the grown layer. This technique will be useful to fabricate high-speed thin film transistors and high-efficiency optical devices on insulating substrates.

  6. Propagating Characteristics of Pulsed Laser in Rain

    Directory of Open Access Journals (Sweden)

    Jing Guo

    2015-01-01

    Full Text Available To understand the performance of laser ranging system under the rain weather condition, we need to know the propagating characteristics of laser pulse in rain. In this paper, the absorption and attenuation coefficients were calculated based on the scattering theories in discrete stochastic media, and the propagating characteristics of laser pulse in rain were simulated and analyzed using Monte-Carlo method. Some simulation results were verified by experiments, and the simulation results are well matched with the experimental data, with the maximal deviation not less than 7.5%. The results indicated that the propagating laser beam would be attenuated and distorted due to the scattering and absorption of raindrops, and the energy attenuation and pulse shape distortion strongly depended on the laser pulse widths.

  7. Apparatus to control and visualize the impact of a high-energy laser pulse on a liquid target

    NARCIS (Netherlands)

    Klein, Alexander L.; Lohse, Detlef; Versluis, Michel; Gelderblom, Hanneke

    2017-01-01

    We present an experimental apparatus to control and visualize the response of a liquid target to a laser-induced vaporization. We use a millimeter-sized drop as target and present two liquid-dye solutions that allow a variation of the absorption coefficient of the laser light in the drop by seven

  8. Non-resonant dynamic stark control of vibrational motion with optimized laser pulses

    DEFF Research Database (Denmark)

    Thomas, Esben Folger; Henriksen, Niels Engholm

    2016-01-01

    The term dynamic Stark control (DSC) has been used to describe methods of quantum control related to the dynamic Stark effect, i.e., a time-dependent distortion of energy levels. Here, we employ analytical models that present clear and concise interpretations of the principles behind DSC. Within ...

  9. DEVICE FOR INVESTIGATION OF MAGNETRON AND PULSED-LASER PLASMA

    Directory of Open Access Journals (Sweden)

    A. P. Burmakov

    2012-01-01

    Full Text Available Various modifications of complex pulsed laser and magnetron deposition thin-film structures unit are presented. They include joint and separate variants of layer deposition. Unit realizes the plasma parameters control and enhances the possibility of laser-plasma and magnetron methods of coatings deposition.

  10. Single-pulse femtosecond laser Bessel beams drilling of high-aspect-ratio microholes based on electron dynamics control

    Science.gov (United States)

    Zhao, Weiwei; Li, Xiaowei; Xia, Bo; Yan, Xueliang; Han, Weina; Lu, Yongfeng; Jiang, Lan

    2014-11-01

    Microholes drilling has attracted extensive research efforts for its broad applications in photonics, microfluidics, optical fibers and many other fields. A femtosecond (fs) laser is a promising tool for high-precision materials processing with reduced recast/microcracks and minimized heat affected zones. But there remain many challenges in hole drilling using conventional fs laser with Gaussian beams, such as low aspect ratio and taper effects. We report small-diameter and high-aspect-ratio microholes with taper free drilling in PMMA (polymethyl methacrylate) using single-pulse fs laser Bessel beams. Axicon is used to transform Gaussian beams into Bessel beams, which then irradiate in the sample by a telescope consisting of plano-convex lens and microscope objective. Using this technique, we enhance the aspect ratio of microholes by 55 times as compared with Gaussian beams. We attribute this high aspect ratio and high quality microholes formation to the unique spatial intensity distribution and propagation stability of Bessel beams, which can effectively adjust the transient localized electron density distribution leading to a long and uniform localized-interacted zone. By using the optimized pulse energy and focal depth position, the microholes diameter ranges between 1.4-2.1 μm and the aspect ratio can exceed 460. This efficient technique is of great potentials for fabrication of microphotonics devices and microfluidics.

  11. Evolution Strategies for Laser Pulse Compression

    NARCIS (Netherlands)

    Monmarché, Nicolas; Fanciulli, Riccardo; Willmes, Lars; Talbi, El-Ghazali; Savolainen, Janne; Collet, Pierre; Schoenauer, Marc; van der Walle, P.; Lutton, Evelyne; Back, Thomas; Herek, Jennifer Lynn

    2008-01-01

    This study describes first steps taken to bring evolutionary optimization technology from computer simulations to real world experimentation in physics laboratories. The approach taken considers a well understood Laser Pulse Compression problem accessible both to simulation and laboratory

  12. Pulse growth dynamics in laser mode locking

    Science.gov (United States)

    Popov, Mark; Gat, Omri

    2018-01-01

    We analyze theoretically and numerically the nonlinear process of pulse formation in mode-locked lasers, starting from a perturbation of a continuous wave. Focusing on weak-to-moderate dispersion systems, we show that pulse growth is initially slow, dominated by a cascade of energy from low to high axial modes, followed by fast strongly nonlinear growth, and finally relaxation to the stable pulse wave form. The pulse grows initially by condensing a fixed amount of energy into a decreasing time interval, with peak power growing toward a finite-time singularity that is checked when the gain bandwidth is saturated by the pulse.

  13. Surface modification of the titanium implant using TEA CO 2 laser pulses in controllable gas atmospheres - Comparative study

    Science.gov (United States)

    Ciganovic, J.; Stasic, J.; Gakovic, B.; Momcilovic, M.; Milovanovic, D.; Bokorov, M.; Trtica, M.

    2012-01-01

    Interaction of a TEA CO2 laser, operating at 10.6 μm wavelength and pulse duration of 100 ns (FWHM), with a titanium implant in various gas atmospheres was studied. The Ti implant surface modification was typically studied at the moderate laser beam energy density/fluence of 28 J/cm2 in the surrounding of air, N2, O2 or He. The energy absorbed from the TEA CO2 laser beam is partially converted to thermal energy, which generates a series of effects, such as melting, vaporization of the molten material, shock waves, etc. The following titanium implant surface changes and phenomena were observed, depending on the gas used: (i) creation of cone-like surface structures in the atmospheres of air, N2 and O2, and dominant micro-holes/pores in He ambient; (ii) hydrodynamic features, most prominent in air; (iii) formation of titanium nitride and titanium oxide layers, and (iv) occurrence of plasma in front of the implant. It can be concluded from this study that the reported laser fluence and gas ambiences can effectively be applied for enhancing the titanium implant roughness and creation of titanium oxides and nitrides on the strictly localized surface area. The appearance of plasma in front of the implants indicates relatively high temperatures created above the surface. This offers a sterilizing effect, facilitating contaminant-free conditions.

  14. Bringing Pulsed Laser Welding into Production

    DEFF Research Database (Denmark)

    Olsen, Flemmming Ove

    1996-01-01

    In this paper, some research and develop-ment activities within pulsed laser welding technology at the Tech-nical University of Denmark will be described. The laser group at the Insti-tute for Manufacturing Technology has nearly 20 years of experience in laser materials process-ing. Inter......-nationally the group is mostly known for its contri-butions to the development of the laser cutting process, but further it has been active within laser welding, both in assisting industry in bringing laser welding into production in several cases and in performing fundamental R & D. In this paper some research...... activities concerning the weldability of high alloyed austenitic stainless steels for mass production industry applying industrial lasers for fine welding will be described. Studies on hot cracking sensitivity of high alloyed austenitic stainless steel applying both ND-YAG-lasers and CO2-lasers has been...

  15. 25 years of pulsed laser deposition

    Science.gov (United States)

    Lorenz, Michael; Ramachandra Rao, M. S.

    2014-01-01

    decade, large-area PLD grown YBa2Cu3O7-δ thin films became a reality for applications in microwave filters for satellite and mobile communication. The material systems that could be covered under the PLD gamut extended to almost all oxides, nitrides and even organics. A second textbook exclusively dedicated to PLD was edited by Rob Eason in 2007 [4], reviewing many possible modifications and extensions of the method. To celebrate 25 years of pulsed laser deposition, Venkatesan organized a symposium on 'Recent Advances in the Pulsed Laser Deposition of Thin Films and Nanostructures' in 2013 [5]. Besides dielectric, ferroelectric and magnetic oxides, the wide-bandgap group II-VI semiconductor ZnO is among the most intensively researched compounds during the last decade. Therefore, this material has become the subject of two introductory reviews in this issue by Opel et al and Tsukazaki et al , to show the state-of-the-art work carried out on ZnO thin films to 2013. The detailed insights into growth parameter control and their impact on the ZnO film performance make both reviews highly instructional not only for specialists, but also for beginners in PLD. The perspective of PLD towards industrial applications largely depends, first, on the ability of the excimer laser suppliers to further increase the laser power and, second, on the deposition schemes to distribute the ablated material homogeneously on technologically relevant substrate areas (8-inch diameter). These developments are explained here by the leading companies dealing with high-power excimer lasers and large-area PLD equipment, such as Coherent Laser Systems GmbH, PVD Products, Inc., and SolMateS B.V. It is also important to note the efforts made by Blank and Rijnders for atomic layer control of PLD by in situ high-pressure reflection high-energy electron diffraction (RHEED), which is now adopted by many groups worldwide. The potential of multi-beam PLD for advanced optical waveguides and of advanced design

  16. Hair removal in hirsute women with normal testosterone levels: a randomized controlled trial of long-pulsed diode laser vs. intense pulsed light.

    Science.gov (United States)

    Haak, C S; Nymann, P; Pedersen, A T; Clausen, H V; Feldt Rasmussen, U; Rasmussen, A K; Main, K; Haedersdal, M

    2010-11-01

    Hirsutism is a common disorder in women of reproductive age, and androgen disturbances may aggravate the condition. Limited evidence exists regarding efficacy of hair removal in this specific population and no data are available for patients with verified normal testosterone levels. To compare efficacy and safety of intense pulsed light (IPL) vs. long-pulsed diode laser (LPDL) in a well-defined group of hirsute women with normal testosterone levels. Thirty-one hirsute women received six allocated split-face treatments with IPL (525-1200 nm; Palomar Starlux IPL system) and LPDL (810 nm; Asclepion MeDioStar XT diode laser). Testosterone levels were measured three times during the study period. Patients with intrinsically normal or medically normalized testosterone levels throughout the study were included in efficacy assessments (n = 23). Endpoints were reduction in hair counts assessed by blinded photoevaluations at baseline and 1, 3 and 6 months after final treatment, patient-evaluated reduction in hairiness, patient satisfaction, treatment-related pain and adverse effects. IPL and LPDL reduced hair counts significantly, with median reductions from baseline of 77%, 53% and 40% for IPL and 68%, 60% and 34% for LDPL at 1, 3 and 6 months, respectively. At 6 months follow-up, there was no significant difference between treatments in terms of hair reduction (P = 0·427), patient assessment of hairiness (P = 0·250) and patient satisfaction (P = 0·125). Pain scores were consistently higher for IPL [median 6, interquartile range (IQR) 4-7] than LPDL (median 3, IQR 2-5) (P IPL and LPDL treatments of facial hairiness, but the efficacy declined over 6 months. © 2010 The Authors. BJD © 2010 British Association of Dermatologists.

  17. Precision machining of pig intestine using ultrafast laser pulses

    Science.gov (United States)

    Beck, Rainer J.; Góra, Wojciech S.; Carter, Richard M.; Gunadi, Sonny; Jayne, David; Hand, Duncan P.; Shephard, Jonathan D.

    2015-07-01

    Endoluminal surgery for the treatment of early stage colorectal cancer is typically based on electrocautery tools which imply restrictions on precision and the risk of harm through collateral thermal damage to the healthy tissue. As a potential alternative to mitigate these drawbacks we present laser machining of pig intestine by means of picosecond laser pulses. The high intensities of an ultrafast laser enable nonlinear absorption processes and a predominantly nonthermal ablation regime. Laser ablation results of square cavities with comparable thickness to early stage colorectal cancers are presented for a wavelength of 1030 nm using an industrial picosecond laser. The corresponding histology sections exhibit only minimal collateral damage to the surrounding tissue. The depth of the ablation can be controlled precisely by means of the pulse energy. Overall, the application of ultrafast lasers to ablate pig intestine enables significantly improved precision and reduced thermal damage to the surrounding tissue compared to conventional techniques.

  18. Modeling Pilot Pulse Control

    Science.gov (United States)

    Bachelder, Edward; Hess, Ronald; Godfroy-Cooper, Martine; Aponso, Bimal

    2017-01-01

    In this study, behavioral models are developed that closely reproduced pulsive control response of two pilots from the experimental pool using markedly different control techniques (styles) while conducting a tracking task. An intriguing find was that the pilots appeared to: 1) produce a continuous, internally-generated stick signal that they integrated in time; 2) integrate the actual stick position; and 3) compare the two integrations to issue and cease pulse commands. This suggests that the pilots utilized kinesthetic feedback in order to perceive and integrate stick position, supporting the hypothesis that pilots can access and employ the proprioceptive inner feedback loop proposed by Hess' pilot Structural Model. The Pulse Models used in conjunction with the pilot Structural Model closely recreated the pilot data both in the frequency and time domains during closed-loop simulation. This indicates that for the range of tasks and control styles encountered, the models captured the fundamental mechanisms governing pulsive and control processes. The pilot Pulse Models give important insight for the amount of remnant (stick output uncorrelated with the forcing function) that arises from nonlinear pilot technique, and for the remaining remnant arising from different sources unrelated to tracking control (i.e. neuromuscular tremor, reallocation of cognitive resources, etc.).

  19. Laser scar revision: comparison of CO2 laser vaporization with and without simultaneous pulsed dye laser treatment.

    Science.gov (United States)

    Alster, T S; Lewis, A B; Rosenbach, A

    1998-12-01

    Over the past decade, the 585-nm pulsed dye laser (PDL) has been used successfully to treat a variety of cutaneous vascular lesions as well as hypertrophic scars. Laser scar revision has been revolutionized by the recent development of high-energy, pulsed carbon dioxide (CO2) laser systems. These new CO2 lasers allow controlled vaporization of thin layers of skin while minimizing damage to surrounding dermal structures. To determine the effect of a high-energy, pulsed CO2 laser alone and in combination with a 585-nm PDL on nonerythematous hypertrophic scars. Twenty patients with nonerythematous hypertrophic scars were treated with a high-energy, pulsed CO2 laser. One-half of each scar was additionally treated with the 585-nm PDL laser. Sequential clinical and photographic analyses were performed independently by two blinded assessors. In addition, erythema reflectance spectrometry measurements were obtained from the scars before and at regular postoperative intervals. Global assessment scores and erythema spectrometry measurements were significantly improved after laser treatment. Combination CO2 and PDL laser treatment resulted in more significant improvement than CO2 laser irradiation alone. Concomitant use of the high-energy, pulsed CO2 and PDL laser systems was superior to CO2 laser vaporization alone for revision of nonerythematous hypertrophic scars. Once again, the vascular specificity of the 585-nm PDL has been linked to improvement in hypertrophic scar tissue.

  20. Electron yield enhancement in a laser wakefield accelerator driven by asymmetric laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Leemans, W.P.; Catravas, P.; Esarey, E.; Geddes, C.G.R.; Toth, C.; Trines, R.; Schroeder, C.B.; Shadwick, B.A.; van Tilborg, J.; Faure, J.

    2002-08-01

    The effect of asymmetric laser pulses on electron yield from a laser wakefield accelerator has been experimentally studied using > 10{sup 19} cm{sup -3} plasmas and a 10 TW, > 45 fs, Ti:Al{sub 2}O{sub 3} laser. Laser pulse shape was controlled through non-linear chirp with a grating pair compressor. Pulses (76 fs FWHM) with a steep rise and positive chirp were found to significantly enhance the electron yield compared to pulses with a gentle rise and negative chirp. Theory and simulation show that fast rising pulses can generate larger amplitude wakes that seed the growth of the self-modulation instability and that frequency chirp is of minimal importance for the experimental parameters.

  1. Hybrid Pulsed Nd:YAG Laser

    Science.gov (United States)

    Miller, Sawyer; Trujillo, Skyler; Fort Lewis College Laser Group Team

    This work concerns the novel design of an inexpensive pulsed Nd:YAG laser, consisting of a hybrid Kerr Mode Lock (KLM) and Q-switch pulse. The two pulse generation systems work independently, non simultaneously of each other, thus generating the ability for the user to easily switch between ultra-short pulse widths or large energy density pulses. Traditionally, SF57 glass has been used as the Kerr medium. In this work, novel Kerr mode-locking mediums are being investigated including: tellurite compound glass (TeO2), carbon disulfide (CS2), and chalcogenide glass. These materials have a nonlinear index of refraction orders of magnitude,(n2), larger than SF57 glass. The Q-switched pulse will utilize a Pockels cell. As the two pulse generation systems cannot be operated simultaneously, the Pockels cell and Kerr medium are attached to kinematic mounts, allowing for quick interchange between systems. Pulse widths and repetition rates will vary between the two systems. A goal of 100 picosecond pulse widths are desired for the mode-locked system. A goal of 10 nanosecond pulse widths are desired for the Q-switch system, with a desired repetition rate of 50 Hz. As designed, the laser will be useful in imaging applications.

  2. RF synchronized short pulse laser ion source

    Energy Technology Data Exchange (ETDEWEB)

    Fuwa, Yasuhiro, E-mail: fuwa@kyticr.kuicr.kyoto-u.ac.jp; Iwashita, Yoshihisa; Tongu, Hiromu; Inoue, Shunsuke; Hashida, Masaki; Sakabe, Shuji [Institute for Chemical Research, Kyoto University, Uji, Kyoto 611-0011 (Japan); Okamura, Masahiro [Collider-Accelerator Department, Brookhaven National Laboratory, Upton, New York 11973 (United States); Yamazaki, Atsushi [Graduate School of Engineering, Nagoya University, Nagoya, Aichi 464-8603 (Japan)

    2016-02-15

    A laser ion source that produces shortly bunched ion beam is proposed. In this ion source, ions are extracted immediately after the generation of laser plasma by an ultra-short pulse laser before its diffusion. The ions can be injected into radio frequency (RF) accelerating bucket of a subsequent accelerator. As a proof-of-principle experiment of the ion source, a RF resonator is prepared and H{sub 2} gas was ionized by a short pulse laser in the RF electric field in the resonator. As a result, bunched ions with 1.2 mA peak current and 5 ns pulse length were observed at the exit of RF resonator by a probe.

  3. Efficacy of pulsed Nd:YAG laser in the treatment of patients with knee osteoarthritis: a randomized controlled trial.

    Science.gov (United States)

    Alayat, Mohamed Salaheldien Mohamed; Aly, Tarek Helmy Ahmed; Elsayed, Aly Elsayed Mohamed; Fadil, Ammar Suliman Mohamed

    2017-04-01

    The purpose of this study was to investigate the effects of pulsed Nd:YAG laser plus glucosamine/chondroitin sulfate (GCS) in patients with knee osteoarthritis (KOA) by examining changes in pain and knee function, as well as synovial thickness (ST) and femoral cartilage thickness (FCT). Sixty-seven male patients participated, with a mean (SD) age of 53.85 (4.39) years, weight of 84.01 (4.70) kg, height of 171.51 (3.96) cm, and BMI of 28.56 (1.22). Group 1 was treated with high-intensity laser therapy (HILT), GCS, and exercises (HILT + GCS + EX). Group 2 was treated with GCS plus exercises (GCS + EX), and group 3 received placebo laser plus exercises (PL + EX). The outcomes measured were pain level and functional disability using the visual analog scale (VAS) and Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC), respectively. ST and FCT were measured by ultrasound examination. Statistical analyses were performed to compare differences between baseline and after 6 weeks of treatment and then after 3 months of follow-up. Statistical significance was set at p treatment of KOA patients.

  4. Surface modification of collagen-based biomaterial induced by pulse width variable femtosecond laser pulses

    Science.gov (United States)

    Daskalova, A.; Selimis, A.; Manousaki, A.; Gray, D.; Ranella, A.; Fotakis, C.

    2013-03-01

    The ability to produce idealized cellular constructs is essential for understanding and controlling intercellular processes and ultimately for producing engineered tissue replacements. Preliminary results have been obtained on collagen modification by irradiation with single and multiple pulses of femtosecond laser with variable pulse duration. Irradiation of collagen thin film by single pulses of femtosecond duration results in creation of foam layer with micrometer thickness. The structure and thickness of the layer strongly depends on the number of the applied laser pulses. The surface properties of collagen thin films before and after Ti-sapphire irradiation with 800 nm were investigated by means of the technique Field Emission Scanning Electron Microscope (FESEM). Based on the FESEM results, it was possible to identify an energy density range as the ablation threshold for collagen thin films. The laser-induced foam formation was characterized over the intensity range 3 - 4.2x1011 W/cm2. The results of the field emission scanning electron microscopy, showed that by tailoring the laser pulse duration, improved the uniformity of the pore network. Examination of the interaction of ultra-short laser pulses with collagen films is useful for controlling the chemical and microstructural modification of the created foam layer.

  5. Regimes of self-pulsing in photonic crystal Fano lasers

    DEFF Research Database (Denmark)

    Rasmussen, Thorsten Svend; Yu, Yi; Mørk, Jesper

    2017-01-01

    Laser self-pulsing was a property exclusive to macroscopic laser systems until recently, where self-pulsing laser operation was demonstrated experimentally and theoretically in a microscopic photonic crystal Fano laser [1]. We now provide a detailed theoretical analysis of the self-pulsing mechan......Laser self-pulsing was a property exclusive to macroscopic laser systems until recently, where self-pulsing laser operation was demonstrated experimentally and theoretically in a microscopic photonic crystal Fano laser [1]. We now provide a detailed theoretical analysis of the self...

  6. Study of pulsed laser deposited ZnGa2O4 : Mn phosphor thin films in an oxygen controlled environment

    Science.gov (United States)

    Thiyagarajan, P.; Kottaisamy, M.; Rama, N.; Ramachandra Rao, M. S.

    2009-08-01

    Photoluminescent properties of ZnGa2O4 : Mn phosphor thin films grown on Si and quartz substrate using the pulsed laser deposition technique under different deposition conditions (i.e. oxygen partial pressure and substrate temperature) are reported. The charge transfer band (283 nm) excitation of the phosphor exhibited green emission (504 nm) due to electronic transition from 4G(4T1)-6S(6A1) of 3d5 Mn2+ ions. The SEM image with elemental composition analysis shows a change in the film porosity and the Ga/Zn ratio with respect to variation in the oxygen partial pressure during the growth of the thin films at a constant temperature (650 °C). The changes in the emission intensity of the films are attributed to the variation in oxygen and Zn content (low vapour pressure) with respect to the change in O2 partial pressure.

  7. Ophthalmic applications of ultrashort pulsed lasers

    Science.gov (United States)

    Juhasz, Tibor; Spooner, Greg; Sacks, Zachary S.; Suarez, Carlos G.; Raksi, Ferenc; Zadoyan, Ruben; Sarayba, Melvin; Kurtz, Ronald M.

    2004-06-01

    Ultrashort laser pulses can be used to create high precision incision in transparent and translucent tissue with minimal damage to adjacent tissue. These performance characteristics meet important surgical requirements in ophthalmology, where femtosecond laser flap creation is becoming a widely used refractive surgery procedure. We summarize clinical findings with femtosecond laser flaps as well as early experiments with other corneal surgical procedures such as corneal transplants. We also review laser-tissue interaction studies in the human sclera and their consequences for the treatment of glaucoma.

  8. Drop shaping by laser-pulse impact

    CERN Document Server

    Klein, Alexander L; Visser, Claas Willem; Lhuissier, Henri; Sun, Chao; Snoeijer, Jacco H; Villermaux, Emmanuel; Lohse, Detlef; Gelderblom, Hanneke

    2015-01-01

    We study the hydrodynamic response of a falling drop hit by a laser pulse. Combining high-speed with stroboscopic imaging we report that a millimeter-sized dyed water drop hit by a milli-Joule nanosecond laser-pulse deforms and propels forward at several meters per second, until it eventually fragments. We show that the drop motion results from the recoil momentum imparted at the drop surface by water vaporization. We measure the propulsion speed and the time-deformation law of the drop, complemented by boundary integral simulations. We explain the drop propulsion and shaping in terms of the laser pulse energy and drop surface tension. These findings are crucial for the generation of extreme ultraviolet (EUV) light in lithography machines.

  9. Development of all solid-state, high average power ultra-short pulse laser for X-ray generation. High average power CPA system and wavefront control of ultra short laser pulse

    Energy Technology Data Exchange (ETDEWEB)

    Harayama, Sayaka; Akaoka, Katsuaki; Tei, Kazuyoku; Kato, Masaaki; Niwa, Yoshito; Maruyama, Yoichiro; Matoba, Toru; Arisawa, Takashi; Takuma, Hiroshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1998-03-01

    We developed a prototype CPA laser system which is pumped by a all solid-state Nd:YAG laser. In a preliminary experiment, the output energy of 52mJ before compression was obtained when the pumping energy was 250mJ. To compensate the wavefront distortion, an adaptive optics has been developed. By using this wavefront control system, the laser beam with the distortion of 0.15{lambda} was obtained. (author)

  10. Pulsed laser illumination of photovoltaic cells

    Science.gov (United States)

    Yater, Jane A.; Lowe, Roland A.; Jenkins, Phillip P.; Landis, Geoffrey A.

    1995-01-01

    In future space missions, free electron lasers (FEL) may be used to illuminate photovoltaic receivers to provide remote power. Both the radio-frequency (RF) and induction FEL produce pulsed rather than continuous output. In this work we investigate cell response to pulsed laser light which simulates the RF FEL format. The results indicate that if the pulse repetition is high, cell efficiencies are only slightly reduced compared to constant illumination at the same wavelength. The frequency response of the cells is weak, with both voltage and current outputs essentially dc in nature. Comparison with previous experiments indicates that the RF FEL pulse format yields more efficient photovoltaic conversion than does an induction FEL format.

  11. Ultrashort laser pulse driven inverse free electron laser accelerator experiment

    Directory of Open Access Journals (Sweden)

    J. T. Moody

    2016-02-01

    Full Text Available In this paper we discuss the ultrashort pulse high gradient inverse free electron laser accelerator experiment carried out at the Lawrence Livermore National Laboratory which demonstrated gradients exceeding 200  MV/m using a 4 TW 100 fs long 800 nm Ti:Sa laser pulse. Due to the short laser and electron pulse lengths, synchronization was determined to be one of the main challenges in this experiment. This made necessary the implementation of a single-shot, nondestructive, electro-optic sampling based diagnostics to enable time-stamping of each laser accelerator shot with <100  fs accuracy. The results of this experiment are expected to pave the way towards the development of future GeV-class IFEL accelerators.

  12. Towards manipulating relativistic laser pulses with 3D printed materials

    CERN Document Server

    Ji, L L; Pukhov, A; Freeman, R R; Akli, K U

    2015-01-01

    Efficient coupling of intense laser pulses to solid-density matter is critical to many applications including ion acceleration for cancer therapy. At relativistic intensities, the focus has been mainly on investigating various laser beams irradiating initially flat interfaces with little or no control over the interaction. Here, we propose a novel approach that leverages recent advancements in 3D direct laser writing (DLW) of materials and high contrast lasers to manipulate the laser-matter interactions on the micro-scales. We demonstrate, via simulations, that usable intensities >10^23Wcm^(-2) could be achieved with current tabletop lasers coupled to 3D printed plasma lenses. We show that these plasma optical elements act not only as a lens to focus laser light, but also as an electromagnetic guide for secondary particle beams. These results open new paths to engineering light-matter interactions at ultra-relativistic intensities.

  13. Size control and luminescence properties of Eu2+:LiCaAlF6 particles prepared by femtosecond pulsed laser ablation

    Science.gov (United States)

    Inoue, Yusuke; Muramatsu, Sotaro; Itoigawa, Fumihiro; Ono, Shingo; Sudo, Masaaki; Fukuda, Kentaro; Yanagida, Takayuki

    2017-10-01

    We have fabricated Eu2+:LiCaAlF6 (Eu:LiCAF) nanoparticles via a dry pulsed laser ablation process using femtosecond laser pulses. The particle size was controlled by adjusting the laser fluence. The crystallographic orientation and chemical composition were preserved in all particles. The typical luminescence peak of Eu:LiCAF crystals at approximately 370 nm was observed in both the PL and X-ray induced luminescence (XL) spectra. The temporal PL profiles of all deposited particles exhibited fast-decay components in addition to the slow-decay components observed in the profile of the bulk crystal. Smaller particles had shorter decay times than larger particles. The fast-decay component of particles with a mean diameter of less than 0.36 μm (˜40 ns) was at least one order of magnitude shorter than the decay time of the bulk crystal (˜1700 ns). Even in the temporal XL profile, all deposited particles showed shorter decay times than the bulk decay time. We attribute these fast-decay components to defects on the particle surface. To confirm the defect level, we investigated the thermally stimulated luminescence of the deposited particles. In addition to an emission peak at approximately 540 K, which was also observed in the spectrum of the bulk crystal, an emission peak corresponding to surface defects at approximately 700 K was observed in the spectrum of the particles.

  14. Laser breakdown in air at ultrahigh laser pulse repetition rates

    Energy Technology Data Exchange (ETDEWEB)

    Kononenko, Vitalii V; Kononenko, Taras V; Pashinin, V P; Gololobov, V M; Konov, Vitalii I [A M Prokhorov General Physics Institute, Russian Academy of Sciences, Moscow (Russian Federation)

    2013-04-30

    Some specific features of interaction of intense femtosecond laser pulses with air at ultrahigh pulse repetition rates have been experimentally studied. Data on the dynamics of plasma cloud expansion and the plasma electron density on time intervals no longer than 10 ns are obtained by femtosecond interferometry. These data are interpreted in terms of the most likely mechanisms of ionised gas recombination. The effect of ultrahigh-frequency laser radiation on a medium was modelled by double-pulse irradiation with a short delay {Delta}t between the pulses: from 1 ps to 11 ns. A nonmonotonic dependence of the degree of air ionisation by the second pulse on the delay time {Delta}t is found; possible mechanisms of these dependences are discussed in terms of the processes of femtosecond radiation absorption in the residual plasma. (extreme light fields and their applications)

  15. New pulsed laser data-acquisition system

    Science.gov (United States)

    Singer, K. D.; Merlin, M. S.; Grossman, C. H.; Garito, A. F.

    1983-01-01

    A new pulsed laser data-acquisition system which can perform the normal operations of boxcar integrators is described. The system is based on a CAMAC standard photocurrent charge-sensitive integrator which is coupled to a laboratory minicomputer. The charge-sensitive integrator is triggered by a gate pulse which is optically synchronized to the laser output. This greatly reduces asynchronous noise. Details of the hardware configuration, the trigger gate circuit, and data averaging software are presented. Flexibility of hardware and software allow for other applications, such as multichannel analysis and other real time data processing.

  16. Lipase biofilm deposited by Matrix Assisted Pulsed Laser Evaporation technique

    Energy Technology Data Exchange (ETDEWEB)

    Aronne, Antonio [Department of Chemical Engineering, Materials and Industrial Production, University of Naples “Federico II”, Napoli (Italy); Bloisi, Francesco, E-mail: bloisi@na.infn.it [SPIN – CNR, Naples (Italy); Department of Physics, University of Naples “Federico II”, Napoli (Italy); Calabria, Raffaela; Califano, Valeria [Istituto Motori – CNR, Naples (Italy); Depero, Laura E. [Department of Mechanical and Industrial Engineering, University of Brescia, Brescia (Italy); Fanelli, Esther [Department of Chemical Engineering, Materials and Industrial Production, University of Naples “Federico II”, Napoli (Italy); Federici, Stefania [Department of Mechanical and Industrial Engineering, University of Brescia, Brescia (Italy); Massoli, Patrizio [Istituto Motori – CNR, Naples (Italy); Vicari, Luciano R.M. [SPIN – CNR, Naples (Italy); Department of Physics, University of Naples “Federico II”, Napoli (Italy)

    2015-05-01

    Highlights: • A lipase film was deposited with Matrix Assisted Pulsed Laser Evaporation technique. • FTIR spectra show that laser irradiation do not damage lipase molecule. • Laser fluence controls the characteristics of complex structure generated by MAPLE. - Abstract: Lipase is an enzyme that finds application in biodiesel production and for detection of esters and triglycerides in biosensors. Matrix Assisted Pulsed Laser Evaporation (MAPLE), a technique derived from Pulsed Laser Deposition (PLD) for deposition of undamaged biomolecules or polymers, is characterized by the use of a frozen target obtained from a solution/suspension of the guest material (to be deposited) in a volatile matrix (solvent). The presence of the solvent avoids or at least reduces the potential damage of guest molecules by laser radiation but only the guest material reaches the substrate in an essentially solvent-free deposition. MAPLE can be used for enzymes immobilization, essential for industrial application, allowing the development of continuous processes, an easier separation of products, the reuse of the catalyst and, in some cases, enhancing enzyme properties (pH, temperature stability, etc.) and catalytic activity in non-aqueous media. Here we show that MAPLE technique can be used to deposit undamaged lipase and that the complex structure (due to droplets generated during extraction from target) of the deposited material can be controlled by changing the laser beam fluence.

  17. Active phase locking of a tiled two-grating assembly for high-energy laser pulse compression using simultaneous controls from far-field profiles and interferometry

    Science.gov (United States)

    Sharma, A. K.; Joshi, A. S.; Naik, P. A.; Gupta, P. D.

    2017-04-01

    A prototype study on active phase locking of a tiled two-grating assembly (TTGA) using four electronic nanometric actuators has been reported, for its use in high-energy laser pulse compression. Measurement and correction of various phase errors of a TTGA have been demonstrated with a precision of sub-50 nm in differential longitudinal translational and sub-10 µrad in differential angular errors using controls derived from simultaneous recording of laser interferogram and far-field profiles of reflected and diffracted beams from TTGA differentiating in-plane rotation with respect to tip error, which is otherwise difficult in the case of using interferometry alone. Multiple-level intensities in the thresholds of the power spectra of apodized interferogram and far-field profiles have been adapted to estimate spatial frequencies and beam peak positions with sub-pixel accuracies.

  18. Route to the minimum pulse duration in normal-dispersion fiber lasers

    Science.gov (United States)

    Chong, Andy; Renninger, William H.; Wise, Frank W.

    2011-01-01

    The factors that control the pulse duration in all-normal-dispersion lasers are identified. To minimize the pulse duration, the cavity dispersion should be as small as possible. For fixed dispersion, increasing pulse energy leads to shorter, but more-structured, pulses. Experiments performed with ordinary single-mode fiber at 1 μm wavelength agree reasonably with numerical simulations, and produce clean ~80-fs pulses. The simulations indicate that 30-fs pulses can be reached at higher energies. PMID:19015693

  19. Quantum Computation with Ultrafast Laser Pulse Shaping

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 10; Issue 6. Quantum Computation with Ultrafast Laser Pulse Shaping. Debabrata Goswami. General Article Volume 10 Issue 6 June 2005 pp 8-14. Fulltext. Click here to view fulltext PDF. Permanent link:

  20. Deep-ultraviolet quantum interference metrology with ultrashort laser pulses

    NARCIS (Netherlands)

    Witte, S.; Zinkstok, R.T.; Ubachs, W.M.G.; Hogervorst, W.; Eikema, K.S.E.

    2005-01-01

    Precision spectroscopy at ultraviolet and shorter wavelengths has been hindered by the poor access of narrow-band lasers to that spectral region. We demonstrate high-accuracy quantum interference metrology on atomic transitions with the use of an amplified train of phase-controlled pulses from a

  1. Group velocity and pulse lengthening of mismatched laser pulses in plasma channels

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, Carl; Benedetti, Carlo; Esarey, Eric; van Tilborg, Jeroen; Leemans, Wim

    2011-07-07

    Analytic solutions are presented to the non-paraxial wave equation describing an ultra-short, low-power, laser pulse propagating in aplasma channel. Expressions for the laser pulse centroid motion and laser group velocity are derived, valid for matched and mismatchedpropagation in a parabolic plasma channel, as well as in vacuum, for an arbitrary Laguerre-Gaussian laser mode. The group velocity of amismatched laser pulse, for which the laser spot size is strongly oscillating, is found to be independent of propagation distance andsignificantly less than that of a matched pulse. Laser pulse lengthening of a mismatched pulse owing to laser mode slippage isexamined and found to dominate over that due to dispersive pulse spreading for sufficiently long pulses. Analytic results are shown tobe in excellent agreement with numerical solutions of the full Maxwell equations coupled to the plasma response. Implications for plasmachannel diagnostics are discussed.

  2. Laser-Induced Damage with Femtosecond Pulses

    Science.gov (United States)

    Kafka, Kyle R. P.

    The strong electric fields of focused femtosecond laser pulses lead to non-equilibrium dynamics in materials, which, beyond a threshold intensity, causes laser-induced damage (LID). Such a strongly non-linear and non-perturbative process renders important LID observables like fluence and intensity thresholds and damage morphology (crater) extremely difficult to predict quantitatively. However, femtosecond LID carries a high degree of precision, which has been exploited in various micro/nano-machining and surface engineering applications, such as human eye surgery and super-hydrophobic surfaces. This dissertation presents an array of experimental studies which have measured the damage behavior of various materials under femtosecond irradiation. Precision experiments were performed to produce extreme spatio-temporal confinement of the femtosecond laser-solid damage interaction on monocrystalline Cu, which made possible the first successful direct-benchmarking of LID simulation with realistic damage craters. A technique was developed to produce laser-induced periodic surface structures (LIPSS) in a single pulse (typically a multi-pulse phenomenon), and was used to perform a pump-probe study which revealed asynchronous LIPSS formation on copper. Combined with 1-D calculations, this new experimental result suggests more drastic electron heating than expected. Few-cycle pulses were used to study the LID performance and morphology of commercial ultra-broadband optics, which had not been systematically studied before. With extensive surface analysis, various morphologies were observed, including LIPSS, swelling (blisters), simple craters, and even ring-shaped structures, which varied depending on the coating design, number of pulses, and air/vacuum test environment. Mechanisms leading to these morphologies are discussed, many of which are ultrafast in nature. The applied damage behavior of multi-layer dielectric mirrors was measured and compared between long pulse (150 ps

  3. Pulsed Power for Solid-State Lasers

    Energy Technology Data Exchange (ETDEWEB)

    Gagnon, W; Albrecht, G; Trenholme, J; Newton, M

    2007-04-19

    Beginning in the early 1970s, a number of research and development efforts were undertaken at U.S. National Laboratories with a goal of developing high power lasers whose characteristics were suitable for investigating the feasibility of laser-driven fusion. A number of different laser systems were developed and tested at ever larger scale in pursuit of the optimum driver for laser fusion experiments. Each of these systems had associated with it a unique pulsed power option. A considerable amount of original and innovative engineering was carried out in support of these options. Ultimately, the Solid-state Laser approach was selected as the optimum driver for the application. Following this, the Laser Program at the Lawrence Livermore National Laboratory and the University of Rochester undertook aggressive efforts directed at developing the technology. In particular, at Lawrence Livermore National Laboratory, a series of laser systems beginning with the Cyclops laser and culminating in the present with the National Ignition Facility were developed and tested. As a result, a large amount of design information for solid-state laser pulsed power systems has been documented. Some of it is in the form of published papers, but most of it is buried in internal memoranda, engineering reports and LLNL annual reports. One of the goals of this book is to gather this information into a single useable format, such that it is easily accessed and understood by other engineers and physicists for use with future designs. It can also serve as a primer, which when seriously studied, makes the subsequent reading of original work and follow-up references considerably easier. While this book deals only with the solid-state laser pulsed power systems, in the bibliography we have included a representative cross section of papers and references from much of the very fine work carried out at other institutions in support of different laser approaches. Finally, in recent years, there has

  4. Laser-Material Interaction of Powerful Ultrashort Laser Pulses

    Energy Technology Data Exchange (ETDEWEB)

    Komashko, A

    2003-01-06

    Laser-material interaction of powerful (up to a terawatt) ultrashort (several picoseconds or shorter) laser pulses and laser-induced effects were investigated theoretically in this dissertation. Since the ultrashort laser pulse (USLP) duration time is much smaller than the characteristic time of the hydrodynamic expansion and thermal diffusion, the interaction occurs at a solid-like material density with most of the light energy absorbed in a thin surface layer. Powerful USLP creates hot, high-pressure plasma, which is quickly ejected without significant energy diffusion into the bulk of the material, Thus collateral damage is reduced. These and other features make USLPs attractive for a variety of applications. The purpose of this dissertation was development of the physical models and numerical tools for improvement of our understanding of the process and as an aid in optimization of the USLP applications. The study is concentrated on two types of materials - simple metals (materials like aluminum or copper) and wide-bandgap dielectrics (fused silica, water). First, key physical phenomena of the ultrashort light interaction with metals and the models needed to describe it are presented. Then, employing one-dimensional plasma hydrodynamics code enhanced with models for laser energy deposition and material properties at low and moderate temperatures, light absorption was self-consistently simulated as a function of laser wavelength, pulse energy and length, angle of incidence and polarization. Next, material response on time scales much longer than the pulse duration was studied using the hydrocode and analytical models. These studies include examination of evolution of the pressure pulses, effects of the shock waves, material ablation and removal and three-dimensional dynamics of the ablation plume. Investigation of the interaction with wide-bandgap dielectrics was stimulated by the experimental studies of the USLP surface ablation of water (water is a model of

  5. Analysis of data transmission technique based on pulsed laser

    Science.gov (United States)

    Drozd, T.; Zygmunt, M.; Knysak, P.; Wojtanowski, J.

    2012-03-01

    Pulsed lasers are used mainly in lidar systems as sources of short and highly energetic light pulses. In data transmission systems continuous wave lasers are typically applied, however it is also possible to use pulsed lasers in such systems. Such approach seems to be especially reasonable for devices where a pulsed laser is applied anyway and executes another function (rangefinding). The article discusses a data transmission concept based on a pulsed laser technology. Advantages and limits of such a transmission method are described. Influence of individual transmission elements on the effective data transmission speed is analysed.

  6. Characterization of polymer thin films obtained by pulsed laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Palla-Papavlu, A., E-mail: apalla@nipne.ro [NILPRP, National Institute for Lasers, Plasma and Radiation Physics, 409 Atomistilor Street, PO Box MG-16, Zip RO-077125, Magurele, Bucharest (Romania); Dinca, V.; Ion, V.; Moldovan, A.; Mitu, B.; Luculescu, C.; Dinescu, M. [NILPRP, National Institute for Lasers, Plasma and Radiation Physics, 409 Atomistilor Street, PO Box MG-16, Zip RO-077125, Magurele, Bucharest (Romania)

    2011-04-01

    The development of laser techniques for the deposition of polymer and biomaterial thin films on solid surfaces in a controlled manner has attracted great attention during the last few years. Here we report the deposition of thin polymer films, namely Polyepichlorhydrin by pulsed laser deposition. Polyepichlorhydrin polymer was deposited on flat substrate (i.e. silicon) using an NdYAG laser (266 nm, 5 ns pulse duration and 10 Hz repetition rate). The obtained thin films have been characterized by atomic force microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy and spectroscopic ellipsometry. It was found that for laser fluences up to 1.5 J/cm{sup 2} the chemical structure of the deposited polyepichlorhydrin polymer thin layers resembles to the native polymer, whilst by increasing the laser fluence above 1.5 J/cm{sup 2} the polyepichlorohydrin films present deviations from the bulk polymer. Morphological investigations (atomic force microscopy and scanning electron microscopy) reveal continuous polyepichlorhydrin thin films for a relatively narrow range of fluences (1-1.5 J/cm{sup 2}). The wavelength dependence of the refractive index and extinction coefficient was determined by ellipsometry studies which lead to new insights about the material. The obtained results indicate that pulsed laser deposition method is potentially useful for the fabrication of polymer thin films to be used in applications including electronics, microsensor or bioengineering industries.

  7. Characterization of polymer thin films obtained by pulsed laser deposition

    Science.gov (United States)

    Palla-Papavlu, A.; Dinca, V.; Ion, V.; Moldovan, A.; Mitu, B.; Luculescu, C.; Dinescu, M.

    2011-04-01

    The development of laser techniques for the deposition of polymer and biomaterial thin films on solid surfaces in a controlled manner has attracted great attention during the last few years. Here we report the deposition of thin polymer films, namely Polyepichlorhydrin by pulsed laser deposition. Polyepichlorhydrin polymer was deposited on flat substrate (i.e. silicon) using an NdYAG laser (266 nm, 5 ns pulse duration and 10 Hz repetition rate). The obtained thin films have been characterized by atomic force microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy and spectroscopic ellipsometry. It was found that for laser fluences up to 1.5 J/cm 2 the chemical structure of the deposited polyepichlorhydrin polymer thin layers resembles to the native polymer, whilst by increasing the laser fluence above 1.5 J/cm 2 the polyepichlorohydrin films present deviations from the bulk polymer. Morphological investigations (atomic force microscopy and scanning electron microscopy) reveal continuous polyepichlorhydrin thin films for a relatively narrow range of fluences (1-1.5 J/cm 2). The wavelength dependence of the refractive index and extinction coefficient was determined by ellipsometry studies which lead to new insights about the material. The obtained results indicate that pulsed laser deposition method is potentially useful for the fabrication of polymer thin films to be used in applications including electronics, microsensor or bioengineering industries.

  8. Laser-pulsed plasma chemistry: Laser-initiated plasma oxidation of niobium

    Science.gov (United States)

    Marks, R. F.; Pollak, R. A.; Avouris, Ph.; Lin, C. T.; Théfaine, Y. J.

    1983-03-01

    We report the first observation of the chemical modification of a solid surface exposed to an ambient gas plasma initiated by the interaction of laser radiation with the same surface. A new technique, which we designate laser-pulsed plasma chemistry (LPPC), is proposed for activating heterogeneous chemical reactions at solid surfaces in a gaseous ambient by means of a plasma initiated by laser radiation. Results for niobium metal in one atmosphere oxygen demonstrate single-pulse, self-limiting oxide growth induced by a pulsed CO2 laser. X-ray photoelectron spectroscopy (XPS or ESCA) was used to monitor surface chemical composition changes and thickness control of thin (1 to 5 nm) reaction product layers. The dependence of single-pulse oxide growth upon laser fluence is observed to be monotonic for oxide thicknesses up to 5 nm. Composition of the oxide Nb2O5-δ, formed by such an optically driven plasma, is similar to that formed by low-temperature oxidation processes such as rf plasma oxidation; however, the valence defect δ of the LPPC oxide is a least two to five times lower. Interdiffusion at the oxide/metal interface becomes important at higher irradiances and is activated by direct optical coupling with the solid or by plasma-mediated thermal coupling. Under ultrahigh vacuum, CO2 laser irradiances greater than 0.9 J cm-2 per pulse thin the surface oxide.

  9. Pulsed lasers in speckle photography: error owing to pulse width.

    Science.gov (United States)

    Joenathan, C; Blair, S M; Ganesan, A R

    1993-01-10

    The effect of the pulse width of a pulsed laser in the studies of speckle velocimetry and transient vibration analysis is discussed. Because of the motion of the object during an exposure, a sine function is obtained by using the pointwise filtering method. This function modulates the halo along with the Young's fringes. It is shown that for high object velocities the sinc function modifies the halo distribution; as a result, the error in calculating the fringe position increases. An aperture geometry for which the autocorrelation halo is made constant in certain regions is proposed in which the intensity variation in this region is the result of the modulating sinc function only. A closed-form solution for the shift in the position of the fringes in this region is obtained. Experimental results of the simulation are presented.

  10. Self-controlled Study of Onychomycosis Treated with Long-pulsed Nd:YAG 1064-nm Laser Combined with Itraconazole

    Directory of Open Access Journals (Sweden)

    Yan Li

    2016-01-01

    Conclusions: For patients with mild or moderate onychomycosis, we recommended a pure medication treatment or combination treatment with medication and laser. For those patients with severe onychomycosis, we recommended a combination of medication and laser therapy.

  11. Plasma generated during underwater pulsed laser processing

    Science.gov (United States)

    Hoffman, Jacek; Chrzanowska, Justyna; Moscicki, Tomasz; Radziejewska, Joanna; Stobinski, Leszek; Szymanski, Zygmunt

    2017-09-01

    The plasma induced during underwater pulsed laser ablation of graphite is studied both experimentally and theoretically. The results of the experiment show that the maximum plasma temperature of 25000 K is reached 20 ns from the beginning of the laser pulse and decreases to 6500 K after 1000 ns. The observed OH absorption band shows that the plasma plume is surrounded by the thin layer of dissociated water vapour at a temperature around 5500 K. The hydrodynamic model applied shows similar maximum plasma temperature at delay times between 14 ns and 30 ns. The calculations show also that already at 14th ns, the plasma electron density reaches 0.97·1027 m-3, which is the critical density for 1064 nm radiation. At the same time the plasma pressure is 2 GPa, which is consisted with earlier measurements of the peak pressure exerted on a target in similar conditions.

  12. Laser Pulse Heating of Spherical Metal Particles

    Directory of Open Access Journals (Sweden)

    Michael I. Tribelsky

    2011-12-01

    Full Text Available We consider the general problem of laser pulse heating of spherical metal particles with the sizes ranging from nanometers to millimeters. We employ the exact Mie solution of the diffraction problem and solve the heat-transfer equation to determine the maximum temperature rise at the particle surface as a function of optical and thermometric parameters of the problem. Primary attention is paid to the case when the thermal diffusivity of the particle is much larger than that of the environment, as it is in the case of metal particles in fluids. We show that, in this case, for any given duration of the laser pulse, the maximum temperature rise as a function of the particle size reaches a maximum at a certain finite size of the particle. We suggest simple approximate analytical expressions for this dependence, which cover the entire parameter range of the problem and agree well with direct numerical simulations.

  13. Tracing the phase of focused broadband laser pulses

    Science.gov (United States)

    Hoff, Dominik; Krüger, Michael; Maisenbacher, Lothar; Sayler, A. M.; Paulus, Gerhard G.; Hommelhoff, Peter

    2017-10-01

    Precise knowledge of the behaviour of the phase of light in a focused beam is fundamental to understanding and controlling laser-driven processes. More than a hundred years ago, an axial phase anomaly for focused monochromatic light beams was discovered and is now commonly known as the Gouy phase. Recent theoretical work has brought into question the validity of applying this monochromatic phase formulation to the broadband pulses becoming ubiquitous today. Based on electron backscattering at sharp nanometre-scale metal tips, a method is available to measure light fields with sub-wavelength spatial resolution and sub-optical-cycle time resolution. Here we report such a direct, three-dimensional measurement of the spatial dependence of the optical phase of a focused, 4-fs, near-infrared pulsed laser beam. The observed optical phase deviates substantially from the monochromatic Gouy phase--exhibiting a much more complex spatial dependence, both along the propagation axis and in the radial direction. In our measurements, these significant deviations are the rule and not the exception for focused, broadband laser pulses. Therefore, we expect wide ramifications for all broadband laser-matter interactions, such as in high-harmonic and attosecond pulse generation, femtochemistry, ophthalmological optical coherence tomography and light-wave electronics.

  14. Injection of electrons by colliding laser pulses in a laser wakefield accelerator

    CERN Document Server

    Hansson, Martin; Ekerfelt, Henrik; Persson, Anna; Lundh, Olle

    2016-01-01

    To improve the stability and reproducibility of laser wakefield accelerators and to allow for future applications, controlling the injection of electrons is of great importance. This allows us to control the amount of charge in the beams of accelerated electrons and final energy of the electrons. Results are presented from a recent experiment on controlled injection using the scheme of colliding pulses and performed using the Lund multi-terawatt laser. Each laser pulse is split into two parts close to the interaction point. The main pulse is focused on a 2 mm diameter gas jet to drive a nonlinear plasma wave below threshold for self-trapping. The second pulse, containing only a fraction of the total laser energy, is focused to collide with the main pulse in the gas jet under an angle of 150°. Beams of accelerated electrons with low divergence and small energy spread are produced using this set-up. Control over the amount of accelerated charge is achieved by rotating the plane of polarization of the second p...

  15. Temporal structure of X-ray radiation pulses of picosecond laser plasma

    Energy Technology Data Exchange (ETDEWEB)

    Belyaev, V S; Kovkov, D V; Matafonov, A P; Karabadzhak, G F; Raikunov, G G [Central Research Institute of Machine Building, Korolev, Moscow region (Russian Federation); Faenov, A Ya; Pikuz, S A; Skobelev, I Yu; Pikuz, T A; Fokin, D A; Fortov, V E [Joint Institute for High Temperatures, Russian Academy of Sciences, Moscow (Russian Federation); Ignat' ev, G N; Kapitanov, S V; Krapiva, P S; Korotkov, K E [All-Russian Institute of Automatics, Moscow (Russian Federation)

    2013-09-30

    The shape of the X-ray pulse generated by picosecond laser plasma is experimentally studied. The unusual phenomenon was experimentally observed for the first time for targets made of moderate-heavy chemical elements, namely, the pulse of hard X-ray radiation generated by laser plasma at the laser radiation flux of ∼10{sup 18} W cm{sup -2} had a longer duration than the pulse of softer X-ray radiation. A simple kinetic model is suggested for explaining this fact. We have suggested a method for controlling the temporal shape of X-ray pulse emitted by laser plasma by varying the contrast of laser pulse. (interaction of laser radiation with matter)

  16. Pulsed laser deposition of rare earth compounds

    CERN Document Server

    Stone, L A

    2001-01-01

    Magnetostrictive thin films have been deposited using various techniques such as sputtering and evaporation but the use of laser deposition has been limited. This research presents the results from pulsed laser deposition (PLD) of TbFe sub 2 , DyFe sub 2 and Terfenol-D thin films using an infra red Transversely Excited Atmospheric (TEA) CO sub 2 laser at lambda approx 10.6 mu m and an ultra violet Argon-Fluoride (ArF) excimer laser at lambda approx 193 nm. Results have showed that the TEA CO sub 2 laser under the range of conditions studied is not suitable for the production of magnetostrictive films. The problems experienced are a mixture of mostly fracture debris at low fluences (F approx 20 Jcm sup - sup 2) and melt droplets at high fluences (F approx 60 Jcm sup - sup 2). In all cases the destruction of the target is a major problem, with the Terfenol-D targets being the worst affected. Thin films produced were all iron rich. The use of an excimer laser has proved more successful in providing stoichiometri...

  17. A Preliminary In Vitro Study on the Efficacy of High-Power Photodynamic Therapy (HLLT): Comparison between Pulsed Diode Lasers and Superpulsed Diode Lasers and Impact of Hydrogen Peroxide with Controlled Stabilization

    OpenAIRE

    Gianluigi Caccianiga; Marco Baldoni; Carlo Angelo Ghisalberti; Alessio Paiusco

    2016-01-01

    Aim. In periodontology lasers have been suggested for the photodynamic therapy (PDT): such therapy can be defined as the inactivation of cells, microorganisms, or molecules induced by light and not by heat. The aim of this study was to evaluate results of PDT using a 980?nm diode laser (Wiser Doctor Smile, Lambda SPA, Italy) combined with hydrogen peroxide, comparing a pulsed diode laser (LI) activity to a high-frequency superpulsed diode laser (LII). Materials and Methods. Primary fibroblast...

  18. Ultrafast laser pulses for medical applications

    Science.gov (United States)

    Lubatschowski, Holger; Heisterkamp, Alexander; Will, Fabian; Serbin, Jesper; Bauer, Thorsten; Fallnich, Carsten; Welling, Herbert; Mueller, Wiebke; Schwab, Burkard; Singh, Ajoy I.; Ertmer, Wolfgang

    2002-04-01

    Ultrafast lasers have become a promising tool for micromachining and extremely precise ablation of all kinds of materials. Due to the low energy threshold, thermal and mechanical side effects are limited to the bu micrometers range. The neglection of side effects enables the use of ultrashort laser pulses in a broad field of medical applications. Moreover, the interaction process based on nonlinear absorption offers the opportunity to process transparent tissue three dimensionally inside the bulk. We demonstrate the feasibility of surgical procedures in different fields of medical interest: in ophthalmology intrastromal cutting and preparing of cornael flaps for refractive surgery in living animals is presented. Besides, the very low mechanical side effects enables the use of fs- laser in otoralyngology to treat ocecular bones. Moreover, the precise cutting quality can be used in fields of cardiovascular surgery for the treatment of arteriosklerosis as well as in dentistry to remove caries from dental hard tissue.

  19. Pulsed Nd-YAG laser in endodontics

    Science.gov (United States)

    Ragot-Roy, Brigitte; Severin, Claude; Maquin, Michel

    1994-12-01

    The purpose of this study was to establish an operative method in endodontics. The effect of a pulsed Nd:YAG laser on root canal dentin has been examined with a scanning electron microscope. Our first experimentation was to observe the impacts carried out perpendicularly to root canal surface with a 200 micrometers fiber optic in the presence of dye. Secondarily, the optical fiber was used as an endodontic instrument with black dye. The irradiation was performed after root canal preparation (15/100 file or 40/100 file) or directly into the canal. Adverse effects are observed. The results show that laser irradiation on root canal dentin surfaces induces a nonhomogeneous modified dentin layer, melted and resolidified dentin closed partially dentinal tubules. The removal of debris is not efficient enough. The laser treatment seems to be indicated only for endodontic and periapical spaces sterilization after conventional root canal preparation.

  20. Pulsed pump: Thermal effects in solid state lasers under super ...

    Indian Academy of Sciences (India)

    Home; Journals; Pramana – Journal of Physics; Volume 67; Issue 6. Pulsed ... Pulse pump; thermal effects; thermal lensing; phase shift; diode-pumped solid state laser; super-Gaussian pump profile. Abstract. Solid state laser (SSL) powers can be realistically scaled when pumped by a real, efficient and multimode pulse.

  1. Corneal and skin laser exposures from 1540-nm laser pulses

    Science.gov (United States)

    Johnson, Thomas E.; Mitchell, Michael A.; Rico, Pedro J.; Fletcher, David J.; Eurell, Thomas E.; Roach, William P.

    2000-06-01

    Mechanisms of tissue damage are investigated for skin and cornea exposures from 1540 nm ('eye safe') laser single pulses of 0.8 milli-seconds. New skin model data point out the advantages of using the Yucatan mini-pig versus the Yorkshire pig for in-vivo skin laser exposures. Major advantages found include similarities in thickness and melanin content when compared with human skin. Histology from Yucatan mini-pig skin exposures and the calculation of an initial ED50 threshold indicate that the main photon tissue interaction may not be solely due to water absorption. In-vitro corneal equivalents compared well with in-vivo rabbit cornea exposure under similar laser conditions. In-vivo and in-vitro histology show that initial energy deposition leading to damage occurs intrastromally, while epithelial cells show no direct injury due to laser light absorption.

  2. Comparative study on Pulsed Laser Deposition and Matrix Assisted Pulsed Laser Evaporation of urease thin films

    Energy Technology Data Exchange (ETDEWEB)

    Smausz, Tomi, E-mail: tomi@physx.u-szeged.h [Department of Optics and Quantum Electronics, University of Szeged, H-6701 Szeged, P.O. Box 406 (Hungary); Megyeri, Gabor; Kekesi, Renata; Vass, Csaba [Department of Optics and Quantum Electronics, University of Szeged, H-6701 Szeged, P.O. Box 406 (Hungary); Gyoergy, Eniko; Sima, Felix; Mihailescu, Ion N. [National Institute for Lasers, Plasma and Radiation Physics, Lasers Department, PO Box MG-54, RO-77125, Bucharest-Magurele (Romania); Hopp, Bela [Hungarian Academy of Sciences and University of Szeged, Research Group on Laser Physics, H-6701 Szeged, P.O. Box 406 (Hungary)

    2009-06-01

    Urease thin films were produced by Matrix Assisted Pulsed Laser Evaporation (MAPLE) and Pulsed Laser Deposition from two types of targets: frozen water solutions of urease with different concentrations (1-10% m/v) and pure urease pellets. The fluence of the ablating KrF excimer laser was varied between 300 and 2200 mJ/cm{sup 2}. Fourier transform infrared spectra of the deposited films showed no difference as compared to the original urease. Morphologic studies proved that the films consist of a smooth 'base' layer with embedded micrometer-sized droplets. Absorption-coefficient measurements contradicted the traditional 'absorptive matrix' model for MAPLE deposition. The laser energy was absorbed by urease clusters leading to a local heating-up and evaporation of the frozen matrix from the uppermost layer accompanied by the release of dissolved urease molecules. Significant enzymatic activity of urease was preserved only during matrix assisted transfer.

  3. Photoconductive Semiconductor Switch Technology for Short Pulse Electromagnetics and Lasers

    Energy Technology Data Exchange (ETDEWEB)

    Denison, Gary J.; Helgeson, Wesley D.; Hjalmarson, Harold P.; Loubriel, Guillermo M.; Mar, Alan; O' Malley, Martin W.; Zutavern, Fred J.

    1999-08-05

    High gain photoconductive semiconductor switches (PCSS) are being used to produce high power electromagnetic pulses foc (1) compact, repetitive accelerators, (2) ultra-wide band impulse sources, (3) precision gas switch triggers, (4) optically-activated firesets, and (5) high power optical pulse generation and control. High power, sub-nanosecond optical pulses are used for active optical sensors such as compact optical radars and range-gated hallistic imaging systems. Following a brief introduction to high gain PCSS and its general applications, this paper will focus on PCSS for optical pulse generation and control. PCSS technology can be employed in three distinct approaches to optical pulse generation and control: (1) short pulse carrier injection to induce gain-switching in semiconductor lasers, (2) electro-optical Q-switching, and (3) optically activated Q-switching. The most significant PCSS issues for these applications are switch rise time, jitter, and longevity. This paper will describe both the requirements of these applications and the most recent results from PCSS technology. Experiments to understand and expand the limitations of high gain PCSS will also be described.

  4. Laser-induced back-ablation of aluminum thin films using picosecond laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    BULLOCK, A B

    1999-05-26

    Experiments were performed to understand laser-induced back-ablation of Al film targets with picosecond laser pulses. Al films deposited on the back surface of BK-7 substrates are ablated by picosecond laser pulses propagating into the Al film through the substrate. The ablated Al plume is transversely probed by a time-delayed, two-color sub-picoseond (500 fs) pulse, and this probe is then used to produce self-referencing interferograms and shadowgraphs of the Al plume in flight. Optical emission from the Al target due to LIBA is directed into a time-integrated grating spectrometer, and a time-integrating CCD camera records images of the Al plume emission. Ablated Al plumes are also redeposited on to receiving substrates. A post-experimental study of the Al target and recollected deposit characteristics was also done using optical microscopy, interferometry, and profilometry. In this high laser intensity regime, laser-induced substrate ionization and damage strongly limits transmitted laser fluence through the substrate above a threshold fluence. The threshold fluence for this ionization-based transmission limit in the substrate is dependent on the duration of the incident pulse. The substrate ionization can be used as a dynamic control of both transmitted spatial pulse profile and ablated Al plume shape. The efficiency of laser energy transfer between the laser pulse incident on the Al film and the ablated Al plume is estimated to be of order 5% and is a weak function of laser pulsewidth. The Al plume is highly directed. Low plume divergence ({theta}{sub divergence} < 5{sup o}) shows the ablated plume temperature to be very low at long time delays ( T << 0.5 eV at delays of 255 ns). Spectroscopic observations and calculations indicate that, in early time (t < 100 ps), the Al film region near the substrate/metal interface is at temperatures of order 0.5 eV. Interferograms of Al plumes produced with 0.1 {micro}m films show these plumes to be of high neutral atom

  5. Pulsed laser fluorometry for environmental monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Saunders, G. C.; Martin, J. C.; Jett, J. H.; Wilder, M. E.; Martinez, A.; Bentley, B. F.; Lopez, J.; Hutson, L.

    1990-01-01

    A compact pulsed laser fluorometer has been incorporated into a continuous flow system developed to detect acetylcholinesterase (AChE) inhibitors and/or primary amine compounds in air and water. A pulsed nitrogen laser pumped dye laser excites fluorescent reactants which flow continuously through a quartz flow cell. Data are collected, analyzed, and displayed using a Macintosh II personal computer. For detection of cholinesterase inhibitors the fluorogenic substrate N methylindoxyl acetate is used to monitor the activity of immobilized enzyme. Presence of inhibitors results in a decrease of steady state fluorescence. Detection of compounds containing primary amines is based on their reaction with fluorescamine to rapidly produce intensely fluorescent products. Compounds of interest to our research were amino acids, peptides, and proteins. An increase in steady state fluorescence could be cause to evaluate the reasons for the change. The detection limit of the protein, bovine serum albumin (BSA) in water is 10 ppT. Nebulized BSA concentrated by the LANL air sampler can be detected at sub ppT original air concentration. 16 refs., 14 figs., 3 tabs.

  6. Pulse Front Tilt and Laser Plasma Acceleration

    Science.gov (United States)

    Mittelberger, Daniel; Thévenet, Maxence; Nakamura, Kei; Lehe, Remi; Gonsalves, Anthony; Benedetti, Carlo; Leemans, Wim

    2017-10-01

    Pulse front tilt (PFT) is potentially present in any CPA laser system, but its effects may be overlooked because spatiotemporal pulse characterization is considerably more involved than measuring only spatial or temporal profile. PFT is particularly important for laser plasma accelerators (LPA) because it influences electron beam injection and steering. In this work, experimental results from the BELLA Center will be presented that demonstrate the effect of optical grating misalignment and optical compression, resulting in PFT, on accelerator performance. Theoretical models of laser and electron beam steering will be introduced based on particle-in-cell simulations showing distortion of the plasma wake. Theoretical predictions will be compared with experiments and complimentary simulations, and tolerances on PFT and optical compressor alignment will be developed as a function of LPA performance requirements. This work was supported by the Office of High Energy Physics, Office of Science, US Department of Energy under Contract DE-AC02-05CH11231 and the National Science Foundation under Grant PHY-1415596.

  7. Factors controlling the microstructure of Ce0.9Gd0.1O2-δ films in pulsed laser deposition process

    DEFF Research Database (Denmark)

    Rodrigo, Katarzyna Agnieszka; Heiroth, S.; Döbeli, M.

    2010-01-01

    Films of Ce0.9Gd0.1O2-delta (CGO10) are prepared at a range of conditions by pulsed laser deposition (PLD) on a single crystal Si (100) and MgO (100), and on a polycrystalline Pt/MgO (100) substrate. The relationship between the film microstructure, crystallography, chemical composition and PLD p...

  8. Optimizing chirped laser pulse parameters for electron acceleration in vacuum

    Energy Technology Data Exchange (ETDEWEB)

    Akhyani, Mina; Jahangiri, Fazel; Niknam, Ali Reza; Massudi, Reza, E-mail: r-massudi@sbu.ac.ir [Laser and Plasma Research Institute, Shahid Beheshti University, Tehran 1983969411 (Iran, Islamic Republic of)

    2015-11-14

    Electron dynamics in the field of a chirped linearly polarized laser pulse is investigated. Variations of electron energy gain versus chirp parameter, time duration, and initial phase of laser pulse are studied. Based on maximizing laser pulse asymmetry, a numerical optimization procedure is presented, which leads to the elimination of rapid fluctuations of gain versus the chirp parameter. Instead, a smooth variation is observed that considerably reduces the accuracy required for experimentally adjusting the chirp parameter.

  9. Benefits of cryogenic cooling on the operation of a pulsed CO2 laser

    Indian Academy of Sciences (India)

    2014-01-05

    Jan 5, 2014 ... The paper presents results of a theoretical model of a pulsed electron beam controlled CO2 laser (EBCL) to investigate the effect of cooling on the laser gas mixture. It is shown that cryogenic cooling can significantly improve the performance of the laser. The efficiency of an EBCL improved from 20% to ...

  10. Benefits of cryogenic cooling on the operation of a pulsed CO2 laser

    Indian Academy of Sciences (India)

    2014-01-05

    Jan 5, 2014 ... Abstract. The paper presents results of a theoretical model of a pulsed electron beam controlled. CO2 laser (EBCL) to investigate the effect of cooling on the laser gas mixture. It is shown that cryogenic cooling can significantly improve the performance of the laser. The efficiency of an. EBCL improved from ...

  11. Ultra short pulse laser generated surface textures for anti-ice applications in aviation

    NARCIS (Netherlands)

    Römer, G.W.; Del Cerro, D.A.; Sipkema, R.C.J.; Groenendijk, M.N.W.; Huis in 't Veld, A.J.

    2009-01-01

    By laser ablation with ultra short laser pulses in the pico- and femto-second range, well controlled dual scaled micro- and nano-scaled surface textures can be obtained. The micro-scale of the texture is mainly determined by the dimensions of the laser spot, whereas the superimposed nano-structure

  12. Microencapsulation of silicon cavities using a pulsed excimer laser

    KAUST Repository

    Sedky, Sherif M.

    2012-06-07

    This work presents a novel low thermal-budget technique for sealing micromachined cavities in silicon. Cavities are sealed without deposition, similar to the silicon surface-migration sealing process. In contrast to the 1100°C furnace anneal required for the migration process, the proposed technique uses short excimer laser pulses (24ns), focused onto an area of 23mm 2, to locally heat the top few microns of the substrate, while the bulk substrate remains near ambient temperature. The treatment can be applied to selected regions of the substrate, without the need for special surface treatments or a controlled environment. This work investigates the effect of varying the laser pulse energy from 400 mJ cm 2to 800 mJ cm 2, the pulse rate from 1Hz to 50Hz and the pulse count from 200 to 3000 pulses on sealing microfabricated cavities in silicon. An analytical model for the effect of holes on the surface temperature distribution is derived, which shows that much higher temperatures can be achieved by increasing the hole density. A mechanism for sealing the cavities is proposed, which indicates how complete sealing is feasible. © 2012 IOP Publishing Ltd.

  13. Pulse-spacing manipulation in a passively mode-locked multipulse fiber laser.

    Science.gov (United States)

    Yu, Ying; Wei, Xiaoming; Kang, Jiqiang; Li, Bowen; Wong, Kenneth K Y

    2017-06-12

    Passively mode-locked fiber lasers have been intensively applied in various research fields. However, the passive mode-locking typically operates in free-running regime, which easily produces messy multiple pulses due to the fruitful nonlinear effects involved in optical fibers. Actively controlling those disordered pulses in a passively mode-locked laser is of great interest but rarely studied. In this work, we experimentally investigate a flexible pulse-spacing manipulation in the passively mode-locked multipulse fiber laser by both intracavity and extracavity methods. A tuning range of pulse spacing up to 1.5 ns is achieved. More importantly, continuous pulse-spacing modulation is successfully demonstrated through external optical injection. It is anticipated that the results can contribute to the understanding of laser nonlinear dynamics and pursuing the optimal performance of passively mode-locked fiber lasers for practical applications.

  14. Three-dimensional laser pulse intensity diagnostic for photoinjectors

    Directory of Open Access Journals (Sweden)

    Heng Li

    2011-11-01

    Full Text Available Minimizing the electron-beam emittance of photoinjectors is an important task for maximizing the brightness of the next-generation x-ray facilities, such as free-electron lasers and energy recovery linacs. Optimally shaped laser pulses can significantly reduce emittance. A reliable diagnostic for the laser pulse intensity is required for this purpose. We demonstrate measurement of three-dimensional spatiotemporal intensity profiles, with spatial resolution of 20  μm and temporal resolution of 130 fs. The capability is illustrated by measurements of stacked soliton pulses and pulses from a dissipative-soliton laser.

  15. Crystalline phase control and growth selectivity of β-MnO{sub 2} thin films by remote plasma assisted pulsed laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Abi-Akl, M.; Tabbal, M., E-mail: malek.tabbal@aub.edu.lb; Kassem, W.

    2016-08-01

    In this paper, we exploit the effect of coupling an oxygen remote plasma source to Pulsed Laser Deposition (PLD) for the growth of pure and well crystallized β-MnO{sub 2} films. Films were grown on Si substrates by laser ablation of a MnO target in oxygen ambient and remote plasma. X-Ray Diffraction, Fourier Transform Infra-Red spectroscopy and Raman scattering were used to determine the crystalline structure and bonding in the grown layers, whereas Atomic Force Microscopy was used to study their morphology and surface roughness. Deposition at 500 °C and high oxygen pressure (33.3–66.6 Pa) resulted in the formation of films with roughness of 12 nm consisting of nsutite γ-MnO{sub 2}, a structure characterized by the intergrowth of the pyrolusite β-MnO{sub 2} in a ramsdellite R-MnO{sub 2} matrix. Deposition at the same temperature but low pressure (1.33–3.33 Pa) in oxygen ambient lead to the formation of Mn{sub 2}O{sub 3} whereas plasma activation within the same pressure range induced the growth of single phase highly crystalline β-MnO{sub 2} having smooth surfaces with a roughness value of 0.6 nm. Such results underline the capability of remote plasma assisted PLD in selecting and controlling the crystalline phase of manganese oxide layers. - Highlights: • MnO{sub 2} films were grown by Remote Plasma Assisted Pulsed Laser Deposition. • Crystalline MnO{sub 2} is formed at a substrate temperature of 500 °C. • Smooth crystalline single phase β-MnO{sub 2} films were obtained at 1.33–3.33 Pa. • Deposition at 1.33–3.33 Pa without plasma activation lead to the growth of Mn{sub 2}O{sub 3}. • Without plasma, mixed phases of MnO{sub 2} polymorphs are obtained at 33.3 Pa and above.

  16. Histological difference between pulsed wave laser and continuous wave laser in endovenous laser ablation.

    Science.gov (United States)

    Kansaku, Rei; Sakakibara, Naoki; Amano, Atsushi; Endo, Hisako; Shimabukuro, Takashi; Sueishi, Michiaki

    2015-07-01

    Endovenous laser ablation to saphenous veins has been popular as a minimally invasive treatment for chronic venous insufficiency. However, adverse effects after endovenous laser ablation using continuous wave laser still remain. Pulsed wave with enough short pulse duration and sufficiently long thermal relaxation time may avoid the excess energy delivery, which leads to the perforation of the vein wall. (1) Free radiation: Laser is radiated in blood for 10 s. (2) Endovenous laser ablation: Veins were filled with blood and placed in saline. Endovenous laser ablations were performed. (1) There were clots on the fiber tips with continuous wave laser while no clots with pulsed wave laser. (2) In 980-nm continuous wave, four of 15 specimens had ulcers and 11 of 15 had perforation. In 1470-nm continuous wave with 120 J/cm of linear endovenous energy density, two of three presented ulcers and one of three showed perforation. In 1470-nm continuous wave with 60 J/cm of linear endovenous energy density, two of four had ulcers and two of four had perforation. In 1320-nm pulsed wave, there were neither ulcers nor perforation in the specimens. While endovenous laser ablation using continuous wave results in perforation in many cases, pulsed wave does not lead to perforation. © The Author(s) 2014.

  17. Three types of pulses delivered from a nanotube-mode-locked fiber laser

    Science.gov (United States)

    Yao, X. K.

    2015-07-01

    Three types of pulses are experimentally investigated in a switchable normal-dispersion nanotube-mode-locked fiber laser by adjusting polarizer controller and pump power. They are a standard dissipative-soliton (DS), conventional soliton (CS)-like pulse, and noiselike pulse, which correspond to three mode-locking states. The standard DS with a rectangular spectrum possesses a Gaussian-shape pulse. The CS-like operation has a Lorenz shape, and the spectrum involves several sidebands similar to the CS case. For the noiselike pulse with a bell-shaped spectrum, a 317 fs peak rides upon the 132.5 ps pedestal in the autocorrelation trace. The spectra of these three pulse operations are centered at three close wavelengths. The generation of three such different types of pulses in one identical normal- dispersion laser cavity may find an important application for the future of mode-locked laser research.

  18. Proton acceleration by radially polarized chirped laser pulses

    Directory of Open Access Journals (Sweden)

    Jin-Lu Liu (刘晋陆

    2012-04-01

    Full Text Available Within the framework of plane-wave angular spectrum analysis of electromagnetic fields, a solution for the field of a tightly focused radially polarized (RP chirped laser pulse is presented. With this solution, direct laser acceleration of protons by this kind of RP laser pulses is investigated numerically. It is found that a RP laser pulse with proper negative frequency chirps can lead to efficient proton acceleration, reaching sub-GeV at the laser intensity of 10^{22}  W/cm^{2} from its injection energy of 45 MeV.

  19. High precision laser direct microstructuring system based on bursts of picosecond pulses

    Science.gov (United States)

    Mur, Jaka; Petelin, Jaka; Osterman, Natan; Petkovšek, Rok

    2017-08-01

    We have developed an efficient, high precision system for direct laser microstructuring using fiber laser generated bursts of picosecond pulses. An advanced opto-mechanical system for beam deflection and sample movement, precise pulse energy control, and a custom built fiber laser with the pulse duration of 65 ps have been combined in a compact setup. The setup allows structuring of single-micrometer sized objects with a nanometer resolution of the laser beam positioning due to a combination of acousto-optical laser beam deflection and tight focusing. The precise synchronization of the fiber laser with the pulse burst repetition frequency of up to 100 kHz allowed a wide range of working parameters, including a tuneable number of pulses in each burst with the intra-burst repetition frequency of 40 MHz and delivering exactly one burst of pulses to every chosen position. We have demonstrated that tightly focused bursts of pulses significantly increase the ablation efficiency during the microstructuring of a copper layer and shorten the typical processing time compared to the single pulse per spot regime. We have used a simple short-pulse ablation model to describe our single pulse ablation data and developed an upgrade to the model to describe the ablation with bursts. Bursts of pulses also contribute to a high quality definition of structure edges and sides. The increased ablation efficiency at lower pulse energies compared to the single pulse per spot regime opens a window to utilize compact fiber lasers designed to operate at lower pulse energies, reducing the overall system complexity and size.

  20. Laser and intense pulsed light hair removal technologies

    DEFF Research Database (Denmark)

    Haedersdal, M; Beerwerth, F; Nash, J F

    2011-01-01

    Light-based hair removal (LHR) is one of the fastest growing, nonsurgical aesthetic cosmetic procedures in the United States and Europe. A variety of light sources including lasers, e.g. alexandrite laser (755 nm), pulsed diode lasers (800, 810 nm), Nd:YAG laser (1064 nm) and broad-spectrum inten...

  1. Laser and intense pulsed light hair removal technologies

    DEFF Research Database (Denmark)

    Haedersdal, M; Beerwerth, F; Nash, J F

    2011-01-01

    Light-based hair removal (LHR) is one of the fastest growing, nonsurgical aesthetic cosmetic procedures in the United States and Europe. A variety of light sources including lasers, e.g. alexandrite laser (755 nm), pulsed diode lasers (800, 810 nm), Nd:YAG laser (1064 nm) and broad-spectrum intense...

  2. A Computer Controlled Pulse Programmer for Pulsed NQR Experiments

    OpenAIRE

    Horiuchi, Keizo; 堀内, 敬三

    1987-01-01

    We constructed a computer controlled pulse programmer for the measurement of nuclear quadrupole resonance relaxation times. Programmable interval timer 8253 was used as device for pulse programming. The circuit is very simple and construction is also easy in comparison with the usual pulse programmer. This programmer is sufficiently useful concerning the pulse programming of slimple pulse sequences such as π-τ-π/2 and π/2-τ-π, which are usually used in the measurement of relaxation times. We ...

  3. Repetitive pulses and laser-induced retinal injury thresholds

    Science.gov (United States)

    Lund, David J.

    2007-02-01

    Experimental studies with repetitively pulsed lasers show that the ED 50, expressed as energy per pulse, varies as the inverse fourth power of the number of pulses in the exposure, relatively independently of the wavelength, pulse duration, or pulse repetition frequency of the laser. Models based on a thermal damage mechanism cannot readily explain this result. Menendez et al. proposed a probability-summation model for predicting the threshold for a train of pulses based on the probit statistics for a single pulse. The model assumed that each pulse is an independent trial, unaffected by any other pulse in the train of pulses and assumes that the probability of damage for a single pulse is adequately described by the logistic curve. The requirement that the effect of each pulse in the pulse train be unaffected by the effects of other pulses in the train is a showstopper when the end effect is viewed as a thermal effect with each pulse in the train contributing to the end temperature of the target tissue. There is evidence that the induction of cell death by microcavitation bubbles around melanin granules heated by incident laser irradiation can satisfy the condition of pulse independence as required by the probability summation model. This paper will summarize the experimental data and discuss the relevance of the probability summation model given microcavitation as a damage mechanism.

  4. Layout of NALM fiber laser with adjustable peak power of generated pulses.

    Science.gov (United States)

    Smirnov, Sergey; Kobtsev, Sergey; Ivanenko, Alexey; Kokhanovskiy, Alexey; Kemmer, Anna; Gervaziev, Mikhail

    2017-05-01

    The Letter proposes a new layout of a passively mode-locked fiber laser based on a nonlinear amplifying loop mirror (NALM) with two stretches of active fiber and two independently controlled pump modules. In contrast with conventional NALM configurations using a single piece of active fiber that yields virtually constant peak power, the proposed novel laser features larger than a factor of 2 adjustment range of peak power of generated pulses. The proposed layout also provides independent adjustment of duration and peak power of generated pulses as well as power-independent control of generated pulse spectral width impossible in NALM lasers with a single piece of active fiber.

  5. Pulsed laser deposition of pepsin thin films

    Energy Technology Data Exchange (ETDEWEB)

    Kecskemeti, G. [Department of Optics and Quantum Electronics, University of Szeged, H-6720 Szeged, Dom ter 9 (Hungary)]. E-mail: kega@physx.u-szeged.hu; Kresz, N. [Department of Optics and Quantum Electronics, University of Szeged, H-6720 Szeged, Dom ter 9 (Hungary); Smausz, T. [Hungarian Academy of Sciences and University of Szeged, Research Group on Laser Physics, H-6720 Szeged, Dom ter 9 (Hungary); Hopp, B. [Hungarian Academy of Sciences and University of Szeged, Research Group on Laser Physics, H-6720 Szeged, Dom ter 9 (Hungary); Nogradi, A. [Department of Ophthalmology, University of Szeged, H-6720, Szeged, Koranyi fasor 10-11 (Hungary)

    2005-07-15

    Pulsed laser deposition (PLD) of organic and biological thin films has been extensively studied due to its importance in medical applications among others. Our investigations and results on PLD of a digestion catalyzing enzyme, pepsin, are presented. Targets pressed from pepsin powder were ablated with pulses of an ArF excimer laser ({lambda} = 193 nm, FWHM = 30 ns), the applied fluence was varied between 0.24 and 5.1 J/cm{sup 2}. The pressure in the PLD chamber was 2.7 x 10{sup -3} Pa. The thin layers were deposited onto glass and KBr substrates. Our IR spectroscopic measurements proved that the chemical composition of deposited thin films is similar to that of the target material deposited at 0.5 and 1.3 J/cm{sup 2}. The protein digesting capacity of the transferred pepsin was tested by adapting a modified 'protein cube' method. Dissolution of the ovalbumin sections proved that the deposited layers consisted of catalytically active pepsin.

  6. Long-term effect of pulsed high-intensity laser therapy in the treatment of post-mastectomy pain syndrome: a double blind, placebo-control, randomized study.

    Science.gov (United States)

    Ebid, Anwar Abdelgayed; El-Sodany, Ahmed Mohamed

    2015-08-01

    We assess the long-term effect of pulsed high-intensity laser therapy (HILT) in the treatment of the post-mastectomy pain syndrome (PMPS). A total of 61 women participated in this study (30 in the laser group and 31 in the placebo laser group), with a mean age of 53.56 ± 1.11 years. Patients who were randomly assigned to the laser group received HILT three times per week for 4 weeks, plus a routine physical therapy program (RPTP). The placebo laser group received placebo HILT plus RPTP. The outcomes measured were pain level by visual analog scale (VAS), shoulder range of motion (ROM), and quality of life (QOL). Statistical analysis was performed by ANOVA with repeated measures to compare the differences between baseline and post-treatment measurements and after 12 weeks of follow-up for both groups. The level of statistical significance was set at P placebo group. VAS results showed a significant decrease post-treatment in the laser group relative to the placebo group, and QOL results showed a significant improvement in the laser group compared with the placebo group and still improved after 12 weeks of follow-up. HILT combined with an RPTP appears to be more effective in patients with PMPS than a placebo laser procedure with RPTP.

  7. Studying the mechanism of micromachining by short pulsed laser

    Science.gov (United States)

    Gadag, Shiva

    economical, because the micromachining rates are much higher than in the case of the ultra-short pulsed lasers. Hence, studying the mechanisms of micromachining by nanosecond pulsed laser of semiconductor silicon, transparent dielectric glass and quartz is undertaken for this research work. Laser drilling of an array of miniaturized micro holes is termed as laser micro via. A study of the effect of laser wavelengths, frequency, and energy of the pulses on the depth and diameter of craters and micro via are carried out using high resolution optical microscopy and a nano via 3D profiler. Analytical equations correlating depth and volume of the crater in terms of the optical absorption coefficient and ratio of peak applied to the threshold fluence for ablation of the silicon are derived. The depth of crater is scaled in terms of optical penetration depth times the ratio of crater diameter to the beam diameter. The shorter UV wavelengths are found to be more suitable for ablation of Si and SiO2 than longer IR wavelengths from the study of the absorption coefficient of Si varying with wavelength. Hence, the UV lasers (266 nm or 355 nm) are used for micromachining of Si and SiO2 involving cutting, cleaning, drilling and dicing, micro-milling and texturing of submicron size vertically oriented silicon wires for photovoltaic applications. The high density vertical wires are useful to grab a greater density of solar energy to generate more environmentally-friendly green power. The laser drilling of micro via can be typically of two types: (1) percussion drilling using a stationary laser beam with single or multiple pulses of the laser or (2) trepanned drilling of micro via by the circular motion of laser. Numerical simulation of dynamic drilling of laser micro via of silicon is performed, using control volume (FV) Fluent code in a Cartesian co-ordinate system. Total enthalpy formulation is used to simulate the phase change taking place during the laser ablation process from melting

  8. Pulsed laser ablation of solids basics, theory and applications

    CERN Document Server

    Stafe, Mihai; Puscas, Niculae N

    2014-01-01

    The book introduces ‘the state of the art' of pulsed laser ablation and its applications. It is based on recent theoretical and experimental studies. The book reaches from the basics to advanced topics of pulsed laser ablation. Theoretical and experimental fundamental phenomena involved in pulsed laser ablation are discussed with respect to material properties, laser wavelength, fluence and intensity regime of the light absorbed linearly or non-linearly in the target material. The energy absorbed by the electrons leads to atom/molecule excitation, ionization and/or direct chemical bond breaking and is also transferred to the lattice leading to material heating and phase transitions. Experimental  non-invasive optical methods for analyzing these phenomena in real time are described. Theoretical models for pulsed laser ablation and phase transitions induced by laser beams and laser-vapour/plasma interaction during the plume expansion above the target are also presented. Calculations of the ablation speed and...

  9. Nanospallation induced by a femtosecond laser pulse

    Science.gov (United States)

    Agranat, M. B.; Anisimov, S. I.; Ashitkov, S. I.; Zhakhovskii, V. V.; Inogamov, N. A.; Nishihara, K.; Petrov, Yu. V.

    2008-01-01

    In the present work phenomena are considered related to the interaction of ultra-short laser pulses, τ L~0.1 ps, with metallic targets. The absorption of laser pulse results in formation of thin layer of hot electrons strongly superheated (T e>>T i) relative to the ion temperature, T i. Initial thickness of the layer d heat is small, d heat~δ, where δ~10 nm is the skin layer thickness. Subsequent developments include the following stages: (1) Propagation of electron thermal wave which expands the hot layer d heat; (2) Cooling of electrons due to energy transfer to cold ions; (3) Onset of hydrodynamic motion that constitutes the rarefaction wave with positive pressure; (4) Further expansion of target material leading to the appearance of negative pressure; and (5) Long separation process which begins with nucleation of voids and goes on to the total separation of spallation plate. The thickness of the plate is ~10 nm (we call it nanospallation). Theoretical model involves two-temperature hydrodynamic equations with semiempirical EOS for a metal, electron heat conduction and electron-ion energy exchange. The decay of metastable strongly stretched matter is described by molecular dynamics (MD) simulation with extremely large number of atoms. The experimental setup includes femtosecond chromium-forsterite laser operating in the pump-probe regime. The experiments are performed with gold target. Measured ablation threshold for gold is 1.35 J/cm2 of incident pump light at inclination 45°, p-polarization. Calorimeter measurements give for the absorbed fluence F abs=0.3F inc, therefore the threshold value of F abs is 0.4 J/cm2.

  10. Enhanced 5-aminolevulinic acid-gold nanoparticle conjugate-based photodynamic therapy using pulse laser

    Science.gov (United States)

    Xu, Hao; Yao, Cuiping; Wang, Jing; Chang, Zhennan; Zhang, Zhenxi

    2016-02-01

    The low bioavailability is a crucial limitation for the application of 5-aminolevulinic acid (ALA) in theranostics. In this research, 5-aminolevulinic acid and gold nanoparticle conjugates (ALA-GNPs) were synthesized to improve the bioavailability of ALA and to investigate the impact of ALA photodynamic therapy (ALA-PDT) in Hela cells. A 532 nm pulse laser and light-emitting diode (central wavelengths 502 nm) were jointly used as light sources in PDT research. The results show a 532 nm pulse laser can control ALA release from ALA-GNPs by adjusting the pulse laser dose. This laser control release may be attributed to the heat generation from GNPs under pulse laser irradiation, which indicates accurately adjusting the pulse laser dose to control the drug release in the cell interior can be considered as a new cellular surgery modality. Furthermore, the PDT results in Hela cells indicate the enhancement of ALA release by pulse laser before PDT can promote the efficacy of cell eradication in the light-emitting diode PDT (LED-PDT). This laser mediated drug release system can provide a new online therapy approach in PDT and it can be utilized in the optical monitor technologies based individual theranostics.

  11. Short-pulse high intensity laser thin foil interaction

    Science.gov (United States)

    Audebert, Patrick

    2003-10-01

    The technology of ultrashort pulse laser generation has progressed to the point that optical pulses larger than 10 J, 300 fs duration or shorter are routinely produced. Such pulses can be focused to intensities exceeding 10^18 W/cm^2. With high contrast pulses, these focused intensities can be used to heat solid matter to high temperatures with minimal hydrodynamic expansion, producing an extremely high energy-density state of matter for a short period of time. This high density, high temperature plasma can be studied by x-ray spectroscopy. We have performed experiments on thin foils of different elements under well controlled conditions at the 100 Terawatt laser at LULI to study the characteristics X-ray emission of laser heated solids. To suppress the ASE effect, the laser was frequency doubled. S-polarized light with a peak intensity of 10^19W/cm^2 was used to minimize resonance absorption. To decrease the effect of longitudinal temperature gradients very thin (800 μ) aluminum foil targets were used. We have also studied the effect of radial gradient by limiting the measured x-ray emission zone using 50μ or 100μ pinhole on target. The spectra, in the range 7-8Å, were recorded using a conical crystal spectrometer coupled to a 800 fs resolution streak camera. A Fourier Domain Interferometry (FDI) of the back of the foil was also performed providing a measurement of the hydrodynamic expansion as function of time for each shot. To simulate the experiment, we used the 1D hydrodynamic code FILM with a given set of plasma parameter (ρ, Te) as initial conditions. The X-ray emission was calculated by post processing hydrodynamic results with a collisional-radiative model which uses super-configuration average atomic data. The simulation reproduces the main features of the experimental time resolved spectrum.

  12. Nonlinear interaction of ultraintense laser pulse with relativistic thin ...

    Indian Academy of Sciences (India)

    momentum acquired by the ions as a result of the ultraintense laser pulse focussed on a thin plasma layer in the radiation pressuredominant(RPD) regime. In the RPD regime, the plasma foil is pushed by ultraintense laser pulse when the radiation ...

  13. Property change during nanosecond pulse laser annealing of ...

    Indian Academy of Sciences (India)

    Keywords. SMA; NiTi; pulse laser; thin film; crystallization. Abstract. Nanosecond lasers of different intensities were pulsed into sputter-deposited amorphous thin films of near equiatomic Ni/Ti composition to produce partially crystallized highly sensitive -phase spots surrounded by amorphous regions. Scanning electron ...

  14. Modelling multiple laser pulses for port wine stain treatment

    NARCIS (Netherlands)

    Verkruysse, W.; van Gemert, M. J.; Smithies, D. J.; Nelson, J. S.

    2000-01-01

    Many port wine stains (PWS) are still resistant to pulsed dye laser treatment. However, anecdotal information suggests that multiple-pulse laser irradiation improves patient outcome. Our aims in this note are to explain the underlying mechanism and estimate the possible thermal effects of multiple

  15. Short pulse generation in a passively mode-locked photonic crystal semiconductor laser

    DEFF Research Database (Denmark)

    Heuck, Mikkel; Blaaberg, Søren; Mørk, Jesper

    2010-01-01

    We present a new type of passively mode-locked laser with quantum wells embedded in photonic crystal waveguides operating in the slow light regime, which is capable of emitting sub picosecond pulses with widely controllable properties......We present a new type of passively mode-locked laser with quantum wells embedded in photonic crystal waveguides operating in the slow light regime, which is capable of emitting sub picosecond pulses with widely controllable properties...

  16. Spectral compression of single-photon-level laser pulse

    Science.gov (United States)

    Li, Yuanhua; Xiang, Tong; Nie, Yiyou; Sang, Minghuang; Chen, Xianfeng

    2017-02-01

    We experimentally demonstrate that the bandwidth of single photons laser pulse is compressed by a factor of 58 in a periodically poled lithium niobate (PPLN) waveguide chip. A positively chirped single photons laser pulse and a negatively chirped classical laser pulse are employed to produce a narrowband single photon pulse with new frequency through sum-frequency generation. In our experiment, the frequency and bandwidth of single photons at 1550 nm are simultaneously converted. Our results mark a critical step towards the realization of coherent photonic interface between quantum communication at 1550 nm and quantum memory in the near-visible window.

  17. Plasma channels during filamentation of a femtosecond laser pulse with wavefront astigmatism in air

    Energy Technology Data Exchange (ETDEWEB)

    Dergachev, A A; Kandidov, V P; Shlenov, S A [Lomonosov Moscow State University, Faculty of Physics, Moscow (Russian Federation); Ionin, A A; Mokrousova, D V; Seleznev, L V; Sinitsyn, D V; Sunchugasheva, E S; Shustikova, A P [P N Lebedev Physics Institute, Russian Academy of Sciences, Moscow (Russian Federation)

    2014-12-31

    We have demonstrated experimentally and numerically the possibility of controlling parameters of plasma channels formed during filamentation of a femtosecond laser pulse by introducing astigmatism in the laser beam wavefront. It is found that weak astigmatism increases the length of the plasma channel in comparison with the case of aberration-free focusing and that strong astigmatism can cause splitting of the plasma channel into two channels located one after another on the filament axis. (interaction of laser radiation with matter. laser plasma)

  18. Multielectron dissociative ionization of methane and formaldehyde molecules with optimally tailored intense femtosecond laser pulses

    Science.gov (United States)

    Irani, E.; Anvari, A.; Sadighi-Bonabi, R.; Monfared, M.

    2017-10-01

    The multielectron dissociative ionization of CH4 and CH2O molecules has been investigated using optimum convolution of different dual tailored short laser pulses. Based on three dimensional molecular dynamics simulations and TDDFT approach, the dissociation probability is enhanced by designing the dual chirped-chirped laser pulses and chirped-ordinary laser pulses for formaldehyde molecule. However, it is interesting to notice that the sensitivity of enhanced dissociation probability into different tailored laser pulses is not significant for methane molecule. In this presented modifications, time variation of bond length, velocity, time dependent electron localization function and evolution of the efficient occupation states are presented to analyze the time evolution of molecular dynamics. This work is proved to be a potential way to reduce the controlling costs with a currently available pulse shaping technology.

  19. Chirp of monolithic colliding pulse mode-locked diode lasers

    DEFF Research Database (Denmark)

    Hofmann, M.; Bischoff, S.; Franck, Thorkild

    1997-01-01

    Spectrally resolved streak camera measurements of picosecond pulses emitted by hybridly colliding pulse mode-locked (CPM) laser diodes are presented in this letter. Depending on the modulation frequency both blue-chirped (upchirped) and red-chirped (downchirped) pulses can be observed. The two...

  20. Accuracy of laser measurements improved by pulse autocorrelator electronic system

    Science.gov (United States)

    Campanella, S. J.

    1967-01-01

    Pulse autocorrelator electronic system discriminates between the dispersion effect of a disturbed laser signal and background noise by detecting multipath arrivals of Gaussian-shaped signal pulses. The autocorrelation function is time-dependent and can be determined by integrating the product of a received pulse and its delayed replicas.

  1. Pulse compression in synchronously pumped mode locked Raman lasers.

    Science.gov (United States)

    Granados, Eduardo; Spence, David J

    2010-09-13

    We explain a pulse compression mechanism reported in picosecond Raman lasers pumped by continuous trains of mode-locked pulses. Our theoretical model is based on transient Raman scattering equations, and shows good agreement with the experimental results. The model reveals that the compression effect is produced by a combination of group velocity walk-off and strong pump pulse depletion. We predict the possibilities and the limitations of this technique for constructing highly efficient, low cost, ultrafast Raman lasers in the visible.

  2. Ultra-short pulsed laser engineered metal-glass nanocomposites

    CERN Document Server

    Stalmashonak, Andrei; Abdolvand, Amin

    2013-01-01

    Glasses containing metallic nanoparticles exhibit very promising linear and nonlinear optical properties, mainly due to the surface plasmon resonances (SPRs) of the nanoparticles. The spectral position in the visible and near-infrared range and polarization dependence of the SPR are characteristically determined by the nanoparticles’ shapes. The focus of Ultra-Short Pulsed Laser Engineered Metal-Glass Nanocomposites is the interaction of intense ultra-short laser pulses with glass containing silver nanoparticles embedded in soda-lime glass, and nanostructural modifications in metal-glass nanocomposites induced by such laser pulses. In order to provide a comprehensive physical picture of the processes leading to laser-induced persistent shape transformation of the nanoparticles, series of experimental results investigating the dependences of laser assisted shape modifications of nanoparticles with laser pulse intensity, excitation wavelength, temperature are considered. In addition, the resulting local opti...

  3. Non-invasive treatment to grade 1 essential hypertension by percutaneous laser and electric pulse to acupoint with music: A randomized controlled trial.

    Science.gov (United States)

    Zhan, Hong-Rui; Hong, Zhong-Si; Chen, Yi-Shen; Hong, Hai-Yu; Weng, Ze-Bin; Yang, Zhang-Bin; Shi, Jing-Li; Chen, Zhong-Ben

    2016-09-01

    To study a non-drug therapy for hypertension disease by combining percutaneous laser and electric pulse stimulation to acupoint with music, and to test the efficiency of the combining treatment to grade 1 essential hypertension. A total of 174 patients with grade 1 essential hypertension were randomly assigned to 3 groups with a random number table after Chinese medicine (CM) syndrome differentiation: the photoelectric and musical treatment group (Group 1, with a self-developed multi-mode audio frequency pulse photoelectric therapeutic apparatus), acupuncture group (Group 2), and oral placebo group (Group 3), 58 cases per group. The curative effect of each group was evaluated by the changes of blood pressure and CM syndrome integral before and after treatment. Compared with Group 3, there were significant decrease of blood pressure and CM syndrome integral in Group 1 and Group 2 (P0.05). The multi-mode audio frequency pulse photoelectric therapeutic apparatus, combining music, laser and electric pulse stimulation, is clinically useful for grade 1 essential hypertension. This "three in one" therapy method is non-invasive, easy and simple to handle. It is expected to be popularized as a new alternative treatment.

  4. Efficient delivery of 60 J pulse energy of long pulse Nd: YAG laser ...

    Indian Academy of Sciences (India)

    2014-02-09

    Feb 9, 2014 ... In this work, we have put efforts to efficiently deliver the laser output of 'ceramic reflector'-based long pulse Nd:YAG laser through a 200 m core diameter optical fibre and successfully delivered up to 60 J of pulse energy with 90% transmission efficiency, using a GRADIUM (axial gradient) plano-convex ...

  5. Pulsed laser Doppler measurements of wind shear

    Science.gov (United States)

    Dimarzio, C.; Harris, C.; Bilbro, J. W.; Weaver, E. A.; Burnham, D. C.; Hallock, J. N.

    1979-01-01

    There is a need for a sensor at the airport that can remotely detect, identify, and track wind shears near the airport in order to assure aircraft safety. To determine the viability of a laser wind-shear system, the NASA pulsed coherent Doppler CO2 lidar (Jelalian et al., 1972) was installed in a semitrailer van with a rooftop-mounted hemispherical scanner and was used to monitor thunderstorm gust fronts. Wind shears associated with the gust fronts at the Kennedy Space Center (KSC) between 5 July and 4 August 1978 were measured and tracked. The most significant data collected at KSC are discussed. The wind shears were clearly visible in both real-time velocity vs. azimuth plots and in postprocessing displays of velocities vs. position. The results indicate that a lidar system cannot be used effectively when moderate precipitation exists between the sensor and the region of interest.

  6. Production of picosecond, kilojoule, petawatt laser pulses via Raman amplification of nanosecond pulses

    CERN Document Server

    Trines, R; Bingham, R; Fonseca, R A; Silva, L O; Cairns, R A; Norreys, P A

    2011-01-01

    Raman amplification in plasma has been promoted as a means of compressing picosecond optical laser pulses to femtosecond duration to explore the intensity frontier. Here we show for the first time that it can be used, with equal success, to compress laser pulses from nanosecond to picosecond duration. Simulations show up to 60% energy transfer from pump to probe pulses, implying that multi-kiloJoule ultra-violet petawatt laser pulses can be produced using this scheme. This has important consequences for the demonstration of fast-ignition inertial confinement fusion.

  7. Characteristics and Applications of Spatiotemporally Focused Femtosecond Laser Pulses

    Directory of Open Access Journals (Sweden)

    Chenrui Jing

    2016-12-01

    Full Text Available Simultaneous spatial and temporal focusing (SSTF of femtosecond laser pulses gives rise to strong suppression of nonlinear self-focusing during the propagation of the femtosecond laser beam. In this paper, we begin with an introduction of the principle of SSTF, followed by a review of our recent experimental results on the characterization and application of the spatiotemporally focused pulses for femtosecond laser micromachining. Finally, we summarize all of the results and give a future perspective of this technique.

  8. Laser pulse heating of surfaces and thermal stress analysis

    CERN Document Server

    Yilbas, Bekir S; Al-Aqeeli, Nasser; Al-Qahtani, Hussain M

    2013-01-01

    This book introduces laser pulse heating and thermal stress analysis in materials surface. Analytical temperature treatments and stress developed in the surface region are also explored. The book will help the reader analyze the laser induced stress in the irradiated region and presents solutions for the stress field. Detailed thermal stress analysis in different laser pulse heating situations and different boundary conditions are also presented. Written for surface engineers.

  9. First evidence of end-cap control in the synthesis of long-chain polyynes by intense ultrashort laser pulse irradiation

    CERN Document Server

    Ramadhan, Ali; Wakabayashi, Tomonari; Shiromaru, Haruo; Fujino, Tatsuya; Kodama, Takeshi; Duley, Walter; Sanderson, Joseph

    2016-01-01

    Hydrogen- and methyl-capped polyynes were synthesized by irradiating pure liquid toluene with 35 femtosecond, 300 {\\mu}J laser pulses having a central wavelength of 800 nm, generated by a regeneratively amplified Ti:sapphire tabletop laser at a repetition rate of 1 kHz. Raman spectroscopy was used to confirm the presence of polyynes in the irradiated samples while high-performance liquid chromatography was used to separate hydrogen-capped polyynes up to C18H2 and methyl-capped polyynes up to HC14CH3. These represent the first such methyl-capped polyynes and the longest hydrogen capped chains synthesized to date by the ultrafast laser based method. Furthermore our results show that choice of the starting solvent molecule directly influences the end caps of the polyynes which can be produced.

  10. A method of laser micro-polishing for metallic surface using UV nano-second pulse and CW lasers

    CERN Document Server

    Jang, Pong-Ryol; Ji, Kum-Hyok; Kim, Nam-Chol

    2014-01-01

    During laser micro-polishing, the constant control of laser energy density is a key technology to improve the surface roughness. In this paper, a method which controls the energy density of UV(ultraviolet) pulse laser in real time with the control of CW(continuous wave) laser spot size in laser micro-polishing for metallic surface was presented. The experimental and analytical considerations of several influence factors such as laser spot size, fusion zone and focal offset were investigated. In addition, using a laser micro-polishing system manufactured with this method, the laser micro-polishing experiments on the two different surface shapes of stainless steel 316L were conducted. For the inclined or curved surface, the surface roughness improvements of up to 56.4% and 57.3% were respectively obtained, and the analysis of the results were discussed.

  11. Size-controllable synthesis of Bi/Bi2O3 heterojunction nanoparticles using pulsed Nd:YAG laser deposition and metal-semiconductor-heterojunction-assisted photoluminescence

    Science.gov (United States)

    Patil, Ranjit A.; Wei, Mao-Kuo; Yeh, P.-H.; Liang, Jyun-Bo; Gao, Wan-Ting; Lin, Jin-Han; Liou, Yung; Ma, Yuan-Ron

    2016-02-01

    We synthesized Bi/Bi2O3 heterojunction nanoparticles at various substrate temperatures using the pulsed laser deposition (PLD) technique with a pulsed Nd:YAG laser. The Bi/Bi2O3 heterojunction nanoparticles consisted of Bi nanoparticles and Bi2O3 surface layers. The average diameter of the Bi nanoparticles and the thickness of the Bi2O3 surface layer are linearly proportional to the substrate temperature. The heterojunctions between the Bi nanoparticles and Bi2O3 surface layers, which are the metal-semiconductor heterojunctions, can strongly enhance the photoluminescence (PL) of the Bi/Bi2O3 nanoparticles, because the metallic Bi nanoparticles can provide massive free Fermi-level electrons for the electron transitions in the Bi2O3 surface layers. The enhancement of PL emission at room temperature by metal-semiconductor-heterojunctions make the Bi/Bi2O3 heterojunction nanoparticles potential candidates for use in optoelectronic nanodevices, such as light-emitting diodes (LEDs) and laser diodes (LDs).We synthesized Bi/Bi2O3 heterojunction nanoparticles at various substrate temperatures using the pulsed laser deposition (PLD) technique with a pulsed Nd:YAG laser. The Bi/Bi2O3 heterojunction nanoparticles consisted of Bi nanoparticles and Bi2O3 surface layers. The average diameter of the Bi nanoparticles and the thickness of the Bi2O3 surface layer are linearly proportional to the substrate temperature. The heterojunctions between the Bi nanoparticles and Bi2O3 surface layers, which are the metal-semiconductor heterojunctions, can strongly enhance the photoluminescence (PL) of the Bi/Bi2O3 nanoparticles, because the metallic Bi nanoparticles can provide massive free Fermi-level electrons for the electron transitions in the Bi2O3 surface layers. The enhancement of PL emission at room temperature by metal-semiconductor-heterojunctions make the Bi/Bi2O3 heterojunction nanoparticles potential candidates for use in optoelectronic nanodevices, such as light-emitting diodes

  12. Energy losses estimation during pulsed-laser seam welding

    Czech Academy of Sciences Publication Activity Database

    Šebestová, Hana; Havelková, M.; Chmelíčková, H.

    2014-01-01

    Roč. 45, č. 3 (2014), s. 1116-1121 ISSN 1073-5615 R&D Projects: GA MŠk(CZ) LG13007 Institutional support: RVO:68378271 Keywords : laser welding * pulsed-laser * Nd:YAG laser Subject RIV: JP - Industrial Processing Impact factor: 1.461, year: 2014

  13. PULSED MODE LASER CUTTING OF SHEETS FOR TAILORED BLANKS

    DEFF Research Database (Denmark)

    Bagger, Claus; Olsen, Flemming Ove

    1999-01-01

    This paper describes how the laser cutting process can be optimised in such a way that the cut sheets can subsequently be used to laser weld tailored blanks. In a number of systematic laboratory experiments the effect of cutting speed, assist gas pressure, average laser power and pulse energy was...

  14. Role of laser pre-pulse wavelength and inter-pulse delay on signal enhancement in collinear double-pulse laser-induced breakdown spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Diwakar, P.K., E-mail: pdiwakar@purdue.edu; Harilal, S.S.; Freeman, J.R.; Hassanein, A.

    2013-09-01

    Dual-pulse (DP) laser-induced breakdown spectroscopy (LIBS) provides significant improvement in signal intensity as compared to conventional single-pulse LIBS. We investigated collinear DPLIBS experimental performance using various laser wavelength combinations employing 1064 nm, 532 nm, and 266 nm Nd:YAG lasers. In particular, the role of the pre-pulse laser wavelength, inter-pulse delay times, and energies of the reheating pulses on LIBS sensitivity improvements is studied. Wavelengths of 1064 nm, 532 nm, and 266 nm pulses were used for generating pre-pulse plasma while 1064 nm pulse was used for reheating the pre-formed plasma generated by the pre-pulse. Significant emission intensity enhancement is noticed for all reheated plasma regardless of the pre-pulse excitation beam wavelength compared to single pulse LIBS. A dual peak in signal enhancement was observed for different inter-pulse delays, especially for 1064:1064 nm combinations, which is explained based on temperature measurement and shockwave expansion phenomenon. Our results also show that 266 nm:1064 nm combination provided maximum absolute signal intensity as compared to 1064 nm:1064 nm or 532 nm:1064 nm. - Highlights: • Role of pre-pulse wavelength and inter-pulse delay on LIBS sensitivity was studied. • For NIR:NIR combination, dual peaks in signal enhancement were observed. • UV:NIR combination resulted in maximum absolute signal intensity. • Persistence of neutral species was increased for double pulse.

  15. Fragmentation dynamics of molecular hydrogen in strong ultrashort laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Rudenko, A; Feuerstein, B; Zrost, K; Jesus, V L B de; Ergler, T; Dimopoulou, C; Schroeter, C D; Moshammer, R; Ullrich, J [Max-Planck-Institut fuer Kernphysik, D-69029 Heidelberg (Germany)

    2005-03-14

    We present the results of a systematic experimental study of dissociation and Coulomb explosion of molecular hydrogen induced by intense ultrashort (7-25 fs) laser pulses. Using coincident recoil-ion momentum spectroscopy we can distinguish the contributions from dissociation and double ionization even if they result in the same kinetic energies of the fragments. The dynamics of all fragmentation channels drastically depends on the pulse duration, and for 7 fs pulses becomes extremely sensitive to the pulse shape.

  16. Explosive Nucleosynthesis Study Using Laser Driven γ-ray Pulses

    Directory of Open Access Journals (Sweden)

    Takehito Hayakawa

    2017-03-01

    Full Text Available We propose nuclear experiments using γ-ray pulses provided from high field plasma generated by high peak power laser. These γ-ray pulses have the excellent features of extremely short pulse, high intensity, and continuous energy distribution. These features are suitable for the study of explosive nucleosyntheses in novae and supernovae, such as the γ process and ν process. We discuss how to generate suitable γ-ray pulses and the nuclear astrophysics involved.

  17. All-Fiber, Directly Chirped Laser Source for Chirped-Pulse-Amplification

    Science.gov (United States)

    Xin, Ran

    Chirped-pulse-amplification (CPA) technology is widely used to produce ultra-short optical pulses (sub picosecond to femtoseconds) with high pulse energy. A chirped pulse laser source with flexible dispersion control is highly desirable as a CPA seed. This thesis presents an all-fiber, directly chirped laser source (DCLS) that produces nanosecond, linearly-chirped laser pulses at 1053 nm for seeding high energy CPA systems. DCLS produces a frequency chirp on an optical pulse through direct temporal phase modulation. DCLS provides programmable control for the temporal phase of the pulse, high pulse energy and diffraction-limited beam performance, which are beneficial for CPA systems. The DCLS concept is first described. Its key enabling technologies are identified and their experimental demonstration is presented. These include high-precision temporal phase control using an arbitrary waveform generator, multi-pass phase modulation to achieve high modulation depth, regenerative amplification in a fiber ring cavity and a negative feedback system that controls the amplifier cavity dynamics. A few technical challenges that arise from the multi-pass architecture are described and their solutions are presented, such as polarization management and gain-spectrum engineering in the DCLS fiber cavity. A DCLS has been built and its integration into a high energy OPCPA system is demonstrated. DCLS produces a 1-ns chirped pulse with a 3-nm bandwidth. The temporal phase and group delay dispersion on the DCLS output pulse is measured using temporal interferometry. The measured temporal phase has an ˜1000 rad amplitude and is close to a quadratic shape. The chirped pulse is amplified from 0.9 nJ to 76 mJ in an OPCPA system. The amplified pulse is compressed to close to its Fourier transform limit, producing an intensity autocorrelation trace with a 1.5-ps width. Direct compressed-pulse duration control by adjusting the phase modulation drive amplitude is demonstrated. Limitation

  18. Application of ultrashort laser pulses for intrastromal refractive surgery.

    Science.gov (United States)

    Lubatschowski, H; Maatz, G; Heisterkamp, A; Hetzel, U; Drommer, W; Welling, H; Ertmer, W

    2000-01-01

    Recently, laser systems have become available which generate ultrashort laser pulses with a duration of 100-200 femtoseconds (fs). By generating micro-plasmas inside the corneal stroma with fs pulses, it is possible to achieve a cutting effect inside the tissue while leaving the anterior layers intact. The energy threshold to generate a micro-plasma with fs pulses is some orders of magnitude lower than it is for picosecond or nanosecond pulses. This results in a strong reduction of the thermal and mechanical damage of the surrounding tissue. With a titanium:sapphire fs laser system, the cutting effect on corneal tissue from freshly enucleated porcine eye globes was investigated with different pulse energies. The irradiated samples were examined by light and electron microscopy. The laser-induced pressure transients and the laser-induced bubble formation were analysed with a broadband acoustic transducer and by flash photography. With fs laser pulses, the extent of thermal and mechanical damage of the adjacent tissue is in the order of 1 microm or below and therefore comparable with the tissue alterations after ArF excimer laser ablation. Using pulse energies of approximately 1-2 microJ and a spot diameter of 5-10 microm, intrastromal cuts can be performed very precisely in order to prepare corneal flaps and lenticules. Femtosecond photodisruption has the potential to become an attractive tool for intrastromal refractive surgery.

  19. Synchronized femtosecond laser pulse switching system based nano-patterning technology

    Science.gov (United States)

    Sohn, Ik-Bu; Choi, Hun-Kook; Yoo, Dongyoon; Noh, Young-Chul; Sung, Jae-Hee; Lee, Seong-Ku; Ahsan, Md. Shamim; Lee, Ho

    2017-07-01

    This paper demonstrates the design and development of a synchronized femtosecond laser pulse switching system and its applications in nano-patterning of transparent materials. Due to synchronization, we are able to control the location of each irradiated laser pulse in any kind of substrate. The control over the scanning speed and scanning step of the laser beam enables us to pattern periodic micro/nano-metric holes, voids, and/or lines in various materials. Using the synchronized laser system, we pattern synchronized nano-holes on the surface of and inside various transparent materials including fused silica glass and polymethyl methacrylate to replicate any image or pattern on the surface of or inside (transparent) materials. We also investigate the application areas of the proposed synchronized femtosecond laser pulse switching system in a diverse field of science and technology, especially in optical memory, color marking, and synchronized micro/nano-scale patterning of materials.

  20. Non-Contact Cardiac Activity Monitoring using Pulsed Laser Vibrometer

    Directory of Open Access Journals (Sweden)

    Chen Chia WANG

    2014-01-01

    Full Text Available We demonstrate experimentally the detection of detailed human cardiac mechanical activity in a remote, non-contacting, and non-ionizing manner using a pulsed laser vibrometer. The highly sensitive pulsed laser vibrometer allows the detection of the temporally-phased mechanical events occurring in individual cardiac cycles even from the surface of clothing-covered extremities of the subjects. Fine structures of the detected cardiac traces are identified with their meanings assigned and corroborated using accelerometer and electrocardiogram measurements obtained concurrently with the pulsed laser vibrometer studies.

  1. Production of color centers in PMMA by ultrashort laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Elgul Samad, Ricardo, E-mail: resamad@gmail.co [Instituto de Pesquisas Energeticas e Nucleares, IPEN-CNEN/SP, Av. Prof. Lineu Prestes 2242, Cidade universitaria 05508-000, Sao Paulo, SP (Brazil); Coronato Courrol, Lilia [Departamento de Ciencias Exatas e da Terra, UNIFESP, Diadema, SP (Brazil); Benevolo Lugao, Ademar; Zanardi Freitas, Anderson de; Dias Vieira, Nilson [Instituto de Pesquisas Energeticas e Nucleares, IPEN-CNEN/SP, Av. Prof. Lineu Prestes 2242, Cidade universitaria 05508-000, Sao Paulo, SP (Brazil)

    2010-03-15

    We report here the creation of color centers in commercial, transparent PMMA samples by ultrashort pulses from a Ti:Sapphire laser emitting at 800 nm, with spatial control. Although the 800 nm photon energy is not sufficient to ionize the polymer, the centers are created following a multiphotonic absorption that causes the ionization. We propose that the free electrons quivering motion on the pulse electric field displaces atoms from its equilibrium positions, creating free radicals and double bonds that coalesce into color centers. The absorption and emission spectra of the centers were measured, but a dose-like curve could not be built due to the presence of damages created along with the centers that scatter the excitation and emission lights due to the commercial sample's poor optical quality.

  2. The role of light-induced nanostructures in femtosecond laser micromachining with vector and scalar pulses.

    Science.gov (United States)

    Hnatovsky, Cyril; Shvedov, Vladlen G; Krolikowski, Wieslaw

    2013-05-20

    In this article we compare the results of micromachining of fused silica and silicon with tightly focused scalar (viz., circularly and linearly polarized) and vector (viz., azimuthally and radially polarized) femtosecond laser pulses. We show that drilling with radially polarized pulses produces holes with smoother and better-delineated walls compared with the other polarizations used, whereas linearly polarized pulses can machine 20-nm wide single grooves in fused silica when the electric field of the pulse is aligned perpendicular to the cutting direction. The observed polarization-controlled micromachining is due to the formation of sub-diffraction-limited nanostructures that are optically produced in the multi-pulse irradiation regime.

  3. Erosion resistant anti-ice surfaces generated by ultra short laser pulses

    NARCIS (Netherlands)

    Del Cerro, D.A.; Römer, G.R.B.E.; Huis in't Veld, A.J.

    2010-01-01

    Wetting properties of a wide range of materials can be modified by accurate laser micromachining with ultra short laser pulses. Controlling the surface topography in a micro and sub-micrometer scale allows the generation of water-repellent surfaces, which remain dry and prevent ice accumulation

  4. Pulse-shaping mechanism in colliding-pulse mode-locked laser diodes

    DEFF Research Database (Denmark)

    Bischoff, Svend; Sørensen, Mads Peter; Mørk, J.

    1995-01-01

    The large signal dynamics of passively colliding pulse mode-locked laser diodes is studied. We derive a model which explains modelocking via the interplay of gain and loss dynamics; no bandwidth limiting element is necessary for pulse formation. It is found necessary to have both fast and slow ab...... absorber dynamics to achieve mode-locking. Significant chirp is predicted for pulses emitted from long lasers, in agreement with experiment. The pulse width shows a strong dependence on both cavity and saturable absorber length. (C) 1995 American Institute of Physics.......The large signal dynamics of passively colliding pulse mode-locked laser diodes is studied. We derive a model which explains modelocking via the interplay of gain and loss dynamics; no bandwidth limiting element is necessary for pulse formation. It is found necessary to have both fast and slow...

  5. Hydroxyapatite thin films grown by pulsed laser deposition and matrix assisted pulsed laser evaporation: Comparative study

    Science.gov (United States)

    Popescu-Pelin, G.; Sima, F.; Sima, L. E.; Mihailescu, C. N.; Luculescu, C.; Iordache, I.; Socol, M.; Socol, G.; Mihailescu, I. N.

    2017-10-01

    Pulsed Laser Deposition (PLD) and Matrix Assisted Pulsed Laser Evaporation (MAPLE) techniques were applied for growing hydroxyapatite (HA) thin films on titanium substrates. All experiments were conducted in a reaction chamber using a KrF* excimer laser source (λ = 248 nm, τFWHM ≈ 25 ns). Half of the samples were post-deposition thermally treated at 500 °C in a flux of water vapours in order to restore crystallinity and improve adherence. Coating surface morphologies and topographies specific to the deposition method were evidenced by scanning electron, atomic force microscopy investigations and profilometry. They were shown to depend on deposition technique and also on the post-deposition treatment. Crystalline structure of the coatings evaluated by X-ray diffraction was improved after thermal treatment. Biocompatibility of coatings, cellular adhesion, proliferation and differentiation tests were conducted using human mesenchymal stem cells (MSCs). Results showed that annealed MAPLE deposited HA coatings were supporting MSCs proliferation, while annealed PLD obtained films were stimulating osteogenic differentiation.

  6. Linear Electro Optic Effect for High Repetition Rate Carrier Envelope Phase Control of Ultra Short Laser Pulses

    Directory of Open Access Journals (Sweden)

    Michel Comte

    2013-02-01

    Full Text Available This paper is devoted to analyzing the principle and applications of the linear electro-optic (EO effect for the control of the carrier-envelope-phase (CEP. We introduce and detail here an original method, which relies on the use of an EO dispersive prism pair in a compressor-like configuration. We show that, by choosing an adequate geometry, it is possible to shift the CEP without changing the group delay (isochronous carrier-envelope-phase shifter or change the induced group delay without varying the CEP. According to our calculations, when applying an electric field around 400 V/cm to the rubidium titanyle phosphate (RTP prisms in a double pass configuration (2 × 40 mm total length, one obtains a CEP shift of π rad at 800 nm without inducing a group delay. In contrast, this CEP shift is obtained for an electric field around 1.4 kV/cm in a RTP rectangular slab of the same total length and, in this case, the group delay is of the order of a few fs.

  7. Organic-inorganic nano-composite films for photonic applications made by multi-beam multi-target pulsed laser deposition with remote control of the plume directions

    Science.gov (United States)

    Darwish, Abdalla M.; Moore, Shaelynn; Mohammed, Aziz; Alexander, Deonte'; Bastian, Tyler; Dorlus, Wydglif; Sarkisov, Sergey S.; Patel, Darayas N.; Mele, Paolo; Koplitz, Brent

    2016-09-01

    There has been an explosive interest in the technique of laser assisted deposition of polymer nano-composite films exploiting the matrix assisted pulsed laser evaporation (MAPLE) with regard to the polymer host as can be judged form recent publications.1-4 In MAPLE, a frozen solution of a polymer in a relatively volatile solvent is used as a laser target. The solvent and concentration are selected so that first, the polymer of interest can dissolve to form a dilute, particulate free solution, second, the majority of the laser energy is initially absorbed by the solvent molecules and not by the solute molecules, and third, there is no photochemical reaction between the solvent and the solute. The light-material interaction in MAPLE can be described as a photothermal process. The photon energy absorbed by the solvent is converted to thermal energy that causes the polymer to be heated but the solvent to vaporize. As the surface solvent molecules are evaporated into the gas phase, polymer molecules are exposed at the gas-target matrix interface. The polymer molecules attain sufficient kinetic energy through collective collisions with the evaporating solvent molecules, to be transferred into the gas phase. By careful optimization of the MAPLE deposition conditions (laser wavelength, repetition rate, solvent type, concentration, temperature, and background gas and gas pressure), this process can occur without any significant polymer decomposition. The MAPLE process proceeds layer-by-layer, depleting the target of solvent and polymer in the same concentration as the starting matrix. When a substrate is positioned directly in the path of the plume, a coating starts to form from the evaporated polymer molecules, while the volatile solvent molecules are evacuated by the pump from the deposition chamber. In case of fabrication of polymer nanocomposites, MAPLE targets are usually prepared as nano-colloids of the additives of interest in the initial polymer solutions. Mixing

  8. Phase-coherent optical pulse synthesis from separate femtosecond lasers.

    Science.gov (United States)

    Shelton, R K; Ma, L S; Kapteyn, H C; Murnane, M M; Hall, J L; Ye, J

    2001-08-17

    We generated a coherently synthesized optical pulse from two independent mode-locked femtosecond lasers, providing a route to extend the coherent bandwidth available for ultrafast science. The two separate lasers (one centered at 760 nanometers wavelength, the other at 810 nanometers) are tightly synchronized and phase-locked. Coherence between the two lasers is demonstrated via spectral interferometry and second-order field cross-correlation. Measurements reveal a coherently synthesized pulse that has a temporally narrower second-order autocorrelation width and that exhibits a larger amplitude than the individual laser outputs. This work represents a new and flexible approach to the synthesis of coherent light.

  9. Parabolic similariton Yb-fiber laser with triangular pulse evolution

    Science.gov (United States)

    Wang, Sijia; Wang, Lei

    2016-04-01

    We propose a novel mode-locked fiber laser design which features a passive nonlinear triangular pulse formation and self-similar parabolic pulse amplification intra cavity. Attribute to the nonlinear reshaping progress in the passive fiber, a triangular-profiled pulse with negative-chirp is generated and paved the way for rapid and efficient self-similar parabolic evolution in a following short-length high-gain fiber. In the meanwhile, the accompanied significantly compressed narrow spectrum from this passive nonlinear reshaping also gives the promise of pulse stabilization and gain-shaping robustness without strong filtering. The resulting short average intra-cavity pulse duration, low amplified spontaneous emission (ASE) and low intra-cavity power loss are essential for the low-noise operation. Simulations predict this modelocked fiber laser allows for high-energy ultra-short transform-limited pulse generation exceeding the gain bandwidth. The output pulse has a de-chirped duration (full-width at half maximum, FWHM) of 27 fs. In addition to the ultrafast laser applications, the proposed fiber laser scheme can support low-noise parabolic and triangular pulse trains at the same time, which are also attractive in optical pulse shaping, all-optical signal processing and high-speed communication applications.

  10. An experimental investigation of pulsed laser-assisted machining of AISI 52100 steel

    Science.gov (United States)

    Panjehpour, Afshin; Soleymani Yazdi, Mohammad R.; Shoja-Razavi, Reza

    2014-11-01

    Grinding and hard turning are widely used for machining of hardened bearing steel parts. Laser-assisted machining (LAM) has emerged as an efficient alternative to grinding and hard turning for hardened steel parts. In most cases, continuous-wave lasers were used as a heat source to cause localized heating prior to material removal by a cutting tool. In this study, an experimental investigation of pulsed laser-assisted machining of AISI 52100 bearing steel was conducted. The effects of process parameters (i.e., laser mean power, pulse frequency, pulse energy, cutting speed and feed rate) on state variables (i.e., material removal temperature, specific cutting energy, surface roughness, microstructure, tool wear and chip formation) were investigated. At laser mean power of 425 W with frequency of 120 Hz and cutting speed of 70 m/min, the benefit of LAM was shown by 25% decrease in specific cutting energy and 18% improvement in surface roughness, as compared to those of the conventional machining. It was shown that at constant laser power, the increase of laser pulse energy causes the rapid increase in tool wear rate. Pulsed laser allowed efficient control of surface temperature and heat penetration in material removal region. Examination of the machined subsurface microstructure and microhardness profiles showed no change under LAM and conventional machining. Continuous chips with more uniform plastic deformation were produced in LAM.

  11. Continuous and Pulsed THz generation with molecular gas lasers and photoconductive antennas gated by femtosecond pulses

    Science.gov (United States)

    Cruz, Flavio C.; Nogueira, T.; Costa, Leverson F. L.; Jarschel, Paulo F.; Frateschi, Newton C.; Viscovini, Ronaldo C.; Vieira, Bruno R. B.; Guevara, Victor M. B.; Pereira, Daniel

    2008-04-01

    We report THz generation based on two systems: 1) continuous-wave (cw) laser generation in molecular gas lasers, and 2) short pulse generation in photoconductive antennas, gated by femtosecond near-infrared Ti:sapphire lasers. With the first system, we have generated tens of monochromatic cw laser lines over the last years, extending roughly from 40 microns to several hundred microns. This is done by optical pumping of gas lasers based on polar molecules such as methanol and its isotopes. In the second system, under development, pulsed THz radiation is generated by a photoconductive antenna built in a semi-insulating GaAs substrate excited by femtosecond pulses from a near-infrared (800 nm) Ti:sapphire laser.

  12. Metal Processing with Ultra-Short Laser Pulses

    Energy Technology Data Exchange (ETDEWEB)

    Banks, P S; Feit, M D; Komashko, A M; Perry, M D; Rubenchik, A M; Stuart, B C

    2000-05-01

    Femtosecond laser ablation has been shown to produce well-defined cuts and holes in metals with minimal heat effect to the remaining material. Ultrashort laser pulse processing shows promise as an important technique for materials processing. We will discuss the physical effects associated with processing based experimental and modeling results. Intense ultra-short laser pulse (USLP) generates high pressures and temperatures in a subsurface layer during the pulse, which can strongly modify the absorption. We carried out simulations of USLP absorption versus material and pulse parameters. The ablation rate as function of the laser parameters has been estimated. Since every laser pulse removes only a small amount of material, a practical laser processing system must have high repetition rate. We will demonstrate that planar ablation is unstable and the initially smooth crater bottom develops a corrugated pattern after many tens of shots. The corrugation growth rate, angle of incidence and the polarization of laser electric field dependence will be discussed. In the nonlinear stage, the formation of coherent structures with scales much larger than the laser wavelength was observed. Also, there appears to be a threshold fluence above which a narrow, nearly perfectly circular channel forms after a few hundred shots. Subsequent shots deepen this channel without significantly increasing its diameter. The role of light absorption in the hole walls will be discussed.

  13. Fundamental studies of pulsed laser ablation

    CERN Document Server

    Claeyssens, F

    2001-01-01

    dopant) have resulted in a coherent view of the resulting plume, which exhibits a multi-component structure correlated with different regimes of ablation, which are attributed to ejection from ZnO and ablation from a Zn melt. OES measurements show that the emitting Zn component within the plume accelerates during expansion in vacuum - an observation attributable to the presence of hot, fast electrons in the plume. The same acceleration behaviour is observed in the case of Al atomic emissions resulting from ablation of an Al target in vacuum. Deposition conditions, substrate temperature and background gas pressure were all varied in a quest for optimally aligned, high quality ZnO thin films. Initial ab initio calculations were performed also, to aid in understanding the stability of these c-axis aligned films. The pulsed ultraviolet (lambda = 193, 248 nm) laser ablation of graphite, polycrystalline diamond and ZnO targets has been investigated. Characteristics of the resulting plumes of ablated material have b...

  14. Miniature, Rugged, Pulsed Laser Source for LIDAR Application Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Princeton Optronics proposes to develop a high energy pulsed laser source based on a novel approach. The approach consists of a technique to combine a large number...

  15. 20 W High Efficiency 1550 nm Pulsed Fiber Laser Project

    Data.gov (United States)

    National Aeronautics and Space Administration — High peak power short pulsed lasers have been considered to be an enabling technology to build high power transmitters for future deep space high rate space...

  16. Reduction of the pulse duration of the ultrafast laser pulses of the Two-Photon Laser Scanning Microscopy (2PLSM

    Directory of Open Access Journals (Sweden)

    Reshak Ali

    2008-07-01

    Full Text Available Abstract Background We provide an update of our two-photon laser scanning microscope by compressing or reducing the broadening of the pulse width of ultrafast laser pulses for dispersion precompensation, to enable the pulses to penetrate deeply inside the sample. Findings The broadening comes as the pulses pass through the optical elements. We enhanced and modified the quality and the sharpness of images by enhancing the resolution using special polarizer namely Glan Laser polarizer GL10. This polarizer consists of two prisms separated by air space. This air separation between the two prisms uses to delay the red wavelength when the light leaves the first prism to the air then to second prism. We note a considerable enhancing with using the GL polarizer, and we can see the details of the leaf structure in early stages when we trying to get focus through z-stacks of images in comparison to exactly the same measurements without using GL polarizer. Hence, with this modification we able to reduce the time of exposure the sample to the laser radiation thereby we will reduce the probability of photobleaching and phototoxicity. When the pulse width reduced, the average power of the laser pulses maintained at a constant level. Significant enhancement is found between the two kinds of images of the Two-Photon Excitation Fluorescence (TPEF. Conclusion In summary reduction the laser pulse width allowed to collect more diffraction orders which will used to form the images. The more diffraction orders the higher resolution images.

  17. Carbon dioxide laser with a variable output pulse duration

    Energy Technology Data Exchange (ETDEWEB)

    Apollonov, V.V.; Akhunov, N.; Derzhavin, S.I.; Kononov, I.K.; Sirotkin, A.A.; Firsov, K.N.; Yamshchikov, V.A.

    1983-09-01

    A report is given of the construction of a CO/sub 2/ laser in which the exciting discharge was stabilized by adding readily ionized organic substances to the mixture. The temporal characteristics of the laser emission pulses were investigated for a wide range of active mixtures and pulse durations from 10 ..mu..sec to 150 nsec. A discussion is given of improvements in the output energy distribution over the beam cross section.

  18. Non-Contact Cardiac Activity Monitoring using Pulsed Laser Vibrometer

    OpenAIRE

    Chen Chia WANG; Sudhir TRIVEDI; Susan KUTCHER; Ponciano RODRIGUEZ; Feng JIN; V. SWAMINATHAN; Frank WALTERS; Narasimha S. PRASAD

    2014-01-01

    We demonstrate experimentally the detection of detailed human cardiac mechanical activity in a remote, non-contacting, and non-ionizing manner using a pulsed laser vibrometer. The highly sensitive pulsed laser vibrometer allows the detection of the temporally-phased mechanical events occurring in individual cardiac cycles even from the surface of clothing-covered extremities of the subjects. Fine structures of the detected cardiac traces are identified with their meanings assigned and corrobo...

  19. Ultrashort Laser Pulse Heating of Nanoparticles: Comparison of Theoretical Approaches

    Directory of Open Access Journals (Sweden)

    Renat R. Letfullin

    2008-01-01

    Full Text Available The interaction between nanoparticles and ultrashort laser pulses holds great interest in laser nanomedicine, introducing such possibilities as selective cell targeting to create highly localized cell damage. Two models are studied to describe the laser pulse interaction with nanoparticles in the femtosecond, picosecond, and nanosecond regimes. The first is a two-temperature model using two coupled diffusion equations: one describing the heat conduction of electrons, and the other that of the lattice. The second model is a one-temperature model utilizing a heat diffusion equation for the phonon subsystem and applying a uniform heating approximation throughout the particle volume. A comparison of the two modeling strategies shows that the two-temperature model gives a good approximation for the femtosecond mode, but fails to accurately describe the laser heating for longer pulses. On the contrary, the simpler one-temperature model provides an adequate description of the laser heating of nanoparticles in the femtosecond, picosecond, and nanosecond modes.

  20. Supression of laser breakdown by pulsed nonequilibrium ns discharge

    Science.gov (United States)

    Starikovskiy, A. Y.; Semenov, I. E.; Shneider, M. N.

    2016-10-01

    The avalanche ionization induced by infrared laser pulses was investigated in a pre-ionized argon gas. Pre-ionization was created by a high-voltage pulsed nanosecond discharge developed in the form of a fast ionization wave. Then, behind the front of ionization wave additional avalanche ionization was initiated by the focused Nd-YAG laser pulse. It was shown that the gas pre-ionization inhibits the laser spark generation. It was demonstrated that the suppression of laser spark development in the case of strong gas pre-ionization is because of fast electron energy transfer from the laser beam focal region. The main mechanism of this energy transfer is free electrons diffusion.

  1. Role of laser pre-pulse wavelength and inter-pulse delay on signal enhancement in collinear double-pulse laser-induced breakdown spectroscopy

    Science.gov (United States)

    Diwakar, P. K.; Harilal, S. S.; Freeman, J. R.; Hassanein, A.

    2013-09-01

    Dual-pulse (DP) laser-induced breakdown spectroscopy (LIBS) provides significant improvement in signal intensity as compared to conventional single-pulse LIBS. We investigated collinear DPLIBS experimental performance using various laser wavelength combinations employing 1064 nm, 532 nm, and 266 nm Nd:YAG lasers. In particular, the role of the pre-pulse laser wavelength, inter-pulse delay times, and energies of the reheating pulses on LIBS sensitivity improvements is studied. Wavelengths of 1064 nm, 532 nm, and 266 nm pulses were used for generating pre-pulse plasma while 1064 nm pulse was used for reheating the pre-formed plasma generated by the pre-pulse. Significant emission intensity enhancement is noticed for all reheated plasma regardless of the pre-pulse excitation beam wavelength compared to single pulse LIBS. A dual peak in signal enhancement was observed for different inter-pulse delays, especially for 1064:1064 nm combinations, which is explained based on temperature measurement and shockwave expansion phenomenon. Our results also show that 266 nm:1064 nm combination provided maximum absolute signal intensity as compared to 1064 nm:1064 nm or 532 nm:1064 nm.

  2. Computational design of short pulse laser driven iron opacity experiments

    Science.gov (United States)

    Martin, M. E.; London, R. A.; Goluoglu, S.; Whitley, H. D.

    2017-02-01

    The resolution of current disagreements between solar parameters calculated from models and observations would benefit from the experimental validation of theoretical opacity models. Iron's complex ionic structure and large contribution to the opacity in the radiative zone of the sun make iron a good candidate for validation. Short pulse lasers can be used to heat buried layer targets to plasma conditions comparable to the radiative zone of the sun, and the frequency dependent opacity can be inferred from the target's measured x-ray emission. Target and laser parameters must be optimized to reach specific plasma conditions and meet x-ray emission requirements. The HYDRA radiation hydrodynamics code is used to investigate the effects of modifying laser irradiance and target dimensions on the plasma conditions, x-ray emission, and inferred opacity of iron and iron-magnesium buried layer targets. It was determined that plasma conditions are dominantly controlled by the laser energy and the tamper thickness. The accuracy of the inferred opacity is sensitive to tamper emission and optical depth effects. Experiments at conditions relevant to the radiative zone of the sun would investigate the validity of opacity theories important to resolving disagreements between solar parameters calculated from models and observations.

  3. Pulse Duration of Seeded Free-Electron Lasers

    Science.gov (United States)

    Finetti, Paola; Höppner, Hauke; Allaria, Enrico; Callegari, Carlo; Capotondi, Flavio; Cinquegrana, Paolo; Coreno, Marcello; Cucini, Riccardo; Danailov, Miltcho B.; Demidovich, Alexander; De Ninno, Giovanni; Di Fraia, Michele; Feifel, Raimund; Ferrari, Eugenio; Fröhlich, Lars; Gauthier, David; Golz, Torsten; Grazioli, Cesare; Kai, Yun; Kurdi, Gabor; Mahne, Nicola; Manfredda, Michele; Medvedev, Nikita; Nikolov, Ivaylo P.; Pedersoli, Emanuele; Penco, Giuseppe; Plekan, Oksana; Prandolini, Mark J.; Prince, Kevin C.; Raimondi, Lorenzo; Rebernik, Primoz; Riedel, Robert; Roussel, Eleonore; Sigalotti, Paolo; Squibb, Richard; Stojanovic, Nikola; Stranges, Stefano; Svetina, Cristian; Tanikawa, Takanori; Teubner, Ulrich; Tkachenko, Victor; Toleikis, Sven; Zangrando, Marco; Ziaja, Beata; Tavella, Franz; Giannessi, Luca

    2017-04-01

    The pulse duration, and, more generally, the temporal intensity profile of free-electron laser (FEL) pulses, is of utmost importance for exploring the new perspectives offered by FELs; it is a nontrivial experimental parameter that needs to be characterized. We measured the pulse shape of an extreme ultraviolet externally seeded FEL operating in high-gain harmonic generation mode. Two different methods based on the cross-correlation of the FEL pulses with an external optical laser were used. The two methods, one capable of single-shot performance, may both be implemented as online diagnostics in FEL facilities. The measurements were carried out at the seeded FEL facility FERMI. The FEL temporal pulse characteristics were measured and studied in a range of FEL wavelengths and machine settings, and they were compared to the predictions of a theoretical model. The measurements allowed a direct observation of the pulse lengthening and splitting at saturation, in agreement with the proposed theory.

  4. Diagnostics of pulse contrast for petawatt laser in SGII

    Science.gov (United States)

    Ouyang, Xiaoping; Liu, Daizhong; Zhu, Baoqiang; Zhu, Jian; Zhu, Jianqiang

    2015-02-01

    Pulse contrast is an important parameter for ultrafast pulses. It shall be 108 or higher in order to avoid effect from noise before main pulse. Diagnostics with cross-correlation can achieve high temporal resolution such as ~7fs. Cross-correlation has advantage in pulse contrast measurement than autocorrelation because it can distinguish noise before or after main pulse. High dynamic range is also essential in pulse contrast measurement. Cross-correlation signal from a single shot is converted into a signal series through fiber array, which can be analyzed by a set of a PMT and an oscilloscope. Noise from nonlinear crystal and scatter needs decrease to improve dynamic range. And pulse power is also discussed in pulse contrast experiments. Time delay τ is generated by travel stage in measurement for repetition pulses. Then energy instability will generate error in this measurement. In measurement for single shot pulse, time delay τ is generated by slant angle of beams. The scanning procession is completed with thousands parts of beam section within a single shot, and error will generated from no uniformity in near field. Performance test of pulse contrast measurement is introduced in subsequent sections. Temporal resolution is testified by self-calibration. Dynamic range is judged by a parallel flat. At last pulse contrast of petawatt laser is diagnosed by a single shot cross-correlator with high confidence. The ratio is 10-6 at 50ps before main pulse, and 10-4 at 10ps before main pulse.

  5. Filamentation of ultrashort laser pulses of different wavelengths in ...

    Indian Academy of Sciences (India)

    We investigate the filaments formed by the ultrashort laser pulses with different wavelengths of 400 nm, 586 nm and 800 nm propagating in argon. Numerical results show that, when the input power or the ratio of the input power to the critical power is given, the pulse with 400 nm wavelength has the largest on-axis intensity, ...

  6. Pulse properties of external cavity mode locked semiconductor lasers

    DEFF Research Database (Denmark)

    Mulet, Josep; Kroh, Marcel; Mørk, Jesper

    2006-01-01

    The performance of an external-cavity mode-locked semiconductor laser is investigated both theoretically and experimentally. The optimization analysis focuses on the regimes of stable mode locking and the generation of sub-picosecond optical pulses. We demonstrate stable output pulses down to one...

  7. Imposed layer by layer growth by pulsed laser interval deposition

    NARCIS (Netherlands)

    Koster, Gertjan; Rijnders, Augustinus J.H.M.; Blank, David H.A.; Rogalla, Horst

    1999-01-01

    Pulsed laser deposition has become an important technique to fabricate novel materials. Although there is the general impression that, due to the pulsed deposition, the growth mechanism differs partially from continuous physical and chemical deposition techniques, it has hardly been used. Here, we

  8. Advanced pulse generator and preamplifier for the HELEN laser

    Science.gov (United States)

    Norman, Michael J.; Harvey, E. J.; Hopps, N. W.; Nolan, J. R.; Smith, W. F. E.

    1997-12-01

    A replacement for the HELEN laser has been proposed that would involve a considerable increase in performance up to 100 TW from 32 beams. The design for the new laser is to be based on the technology being developed for the US National Ignition Facility. The pulse generation and preamplification stages employ novel technologies and represent a significant departure from previous designs. As part of the laser replacement development program a pulse generator and preamplifier have been built and installed on the HELEN laser at AWE, based on those employed on the Beamlet laser physics demonstration facility at Lawrence Livermore National Laboratory. As well as providing experience of the technologies involved, this system represents a significant enhancement of the performance of HELEN. Initial pulses are generated by a diode-pumped Q-switched Neodymium-doped Yttrium Lithium Fluoride ring oscillator. These are then launched into optical fiber and transported to a series of two integrated optics amplitude modulators for pulse shaping. The resulting pulses are then transported by optical fibers to a ring regenerative preamplifier for amplification to a level suitable for input to the HELEN laser. We describe this system, its performance and the enhanced capabilities of the HELEN laser resulting from its installation.

  9. Time dependent temperature distribution in pulsed Ti:sapphire lasers

    Science.gov (United States)

    Buoncristiani, A. Martin; Byvik, Charles E.; Farrukh, Usamah O.

    1988-01-01

    An expression is derived for the time dependent temperature distribution in a finite solid state laser rod for an end-pumped beam of arbitrary shape. The specific case of end pumping by circular (constant) or Gaussian beam is described. The temperature profile for a single pump pulse and for repetitive pulse operation is discussed. The particular case of the temperature distribution in a pulsed titanium:sapphire rod is considered.

  10. Application of femtosecond-pulsed lasers for direct optical manipulation of biological functions

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Jonghee; Park, Junseong; Jong Choi, Won [Department of Bio and Brain Engineering, KAIST, Daejeon (Korea, Republic of); Choi, Myunghwan [Graduate School of Nanoscience and Technology, KAIST, Daejeon (Korea, Republic of); Harvard Medical School and Wellman Center for Photomedicine, Massachusetts General Hospital, Boston, MA (United States); Choi, Chulhee [Department of Bio and Brain Engineering, KAIST, Daejeon (Korea, Republic of); KAIST Institute for the BioCentury, KAIST, Daejeon (Korea, Republic of)

    2013-03-15

    Absorption of photon energy by cells or tissue can evoke photothermal, photomechanical, and photochemical effects, depending on the density of the deposited energy. Photochemical effects require a low energy density and can be used for reversible modulation of biological functions. Ultrashort-pulsed lasers have a high intensity due to the short pulse duration, despite its low average energy. Through nonlinear absorption, these lasers can deliver very high peak energy into the submicrometer focus area without causing collateral damage. Absorbed energy delivered by ultrashort-pulsed laser irradiation induces free electrons, which can be readily converted to reactive oxygen species (ROS) and related free radicals in the localized region. Free radicals are best known to induce irreversible biological effects via oxidative modification; however, they have also been proposed to modulate biological functions by releasing calcium ions from intracellular organelles. Calcium can evoke variable biological effects in both excitable and nonexcitable cell types. Controlled stimulation by ultrashort laser pulses generate intracellular calcium waves that can modulate many biological functions, such as cardiomyocyte beat rate, muscle contractility, and blood-brain barrier (BBB) permeability. This article presents optical methods that are useful therapeutic and research tools in the biomedical field and discuss the possible mechanisms responsible for biological modulation by ultrashort-pulsed lasers, especially femtosecond-pulsed lasers. (copyright 2012 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  11. Generation of isolated attosecond pulses by spatial shaping of a femtosecond laser beam

    Energy Technology Data Exchange (ETDEWEB)

    Strelkov, V V; Mevel, E; Constant, E [Centre Lasers Intenses et Applications (CELIA), Domaine du Haut-Carre, Universite Bordeaux 1, 43 Rue Pierre Noailles, 33405 Talence (France)], E-mail: v-strelkov@fpl.gpi.ru

    2008-08-15

    We present a new method for generating isolated attosecond pulses via high-order harmonic generation in gases. It relies on using collective effects to achieve transient phase-matching which provides both a high efficiency and a strong temporal confinement under specific conditions. By controlling the spatial shape of the fundamental beam and the geometry of the laser-gas interaction, this transient phase matching leads to the generation of isolated broadband attosecond pulses with long driving pulses (10-20 fs) even without controlling their carrier envelope phase. Such laser pulses are becoming available at high energy levels and our approach offers a route to increase the energy of isolated attosecond pulses by orders of magnitude as compared to existing sources.

  12. Femtosecond and nanosecond pulsed laser deposition of silicon and germanium

    Energy Technology Data Exchange (ETDEWEB)

    Reenaas, Turid Worren [Department of Physics, Norwegian University of Science and Technology, 7491 Trondheim (Norway); Lee, Yen Sian [Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia); Department of Physics, Faculty of Science, University of Malaya, 50603 Kuala Lumpur (Malaysia); Chowdhury, Fatema Rezwana; Gupta, Manisha; Tsui, Ying Yin [Department of Electrical and Computer Engineering, University of Alberta (Canada); Tou, Teck Yong [Faculty of Engineering, Multimedia University, 63100 Cyberjaya, Selangor (Malaysia); Yap, Seong Ling [Department of Physics, Faculty of Science, University of Malaya, 50603 Kuala Lumpur (Malaysia); Kok, Soon Yie [Faculty of Engineering, Multimedia University, 63100 Cyberjaya, Selangor (Malaysia); Yap, Seong Shan, E-mail: seongshan@gmail.com [Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia)

    2015-11-01

    Highlights: • Ge and Si were deposited by fs and ns laser at room temperature and at vacuum. • Ion of 10{sup 4} ms{sup −1} and 30–200 eV was obtained for ns ablation for Ge and Si. • Highly energetic ions of 10{sup 5} ms{sup −1} with 2–7 KeV were produced in fs laser ablation. • Nanocrystalline Si and Ge were deposited by using fs laser. • Nanoparticles < 10 nm haven been obtained by fs laser. - Abstract: 150 fs Ti:Sapphire laser pulsed laser deposition of Si and Ge were compared to a nanosecond KrF laser (25 ns). The ablation thresholds for ns lasers were about 2.5 J cm{sup −2} for Si and 2.1 J cm{sup −2} for Ge. The values were about 5–10 times lower when fs laser were used. The power densities were 10{sup 8}–10{sup 9} W cm{sup −2} for ns but 10{sup 12} W cm{sup −2} for fs. By using an ion probe, the ions emission at different fluence were measured where the emitting ions achieving the velocity in the range of 7–40 km s{sup −1} and kinetic energy in the range of 30–200 eV for ns laser. The ion produced by fs laser was measured to be highly energetic, 90–200 km s{sup −1}, 2–10 KeV. Two ion peaks were detected above specific laser fluence for both ns and fs laser ablation. Under fs laser ablation, the films were dominated by nano-sized crystalline particles, drastically different from nanosecond pulsed laser deposition where amorphous films were obtained. The ions characteristics and effects of pulse length on the properties of the deposited films were discussed.

  13. Theory and simulation of ultra-short pulse laser interactions

    Energy Technology Data Exchange (ETDEWEB)

    More, R.; Walling, R.; Price, D.; Guethlein, G.; Stewart, R.; Libby, S.; Graziani, F.; Levatin, J. [Lawrence Livermore National Lab., Livermore, CA (United States)

    1998-03-01

    This paper describes recent Livermore work aimed at building computational tools to describe ultra-short pulse laser plasmas. We discuss calculations of laser absorption, atomic data for high-charge ions, and a new idea for linear-response treatment of non-equilibrium phenomena near LTE. (author)

  14. Spatial and temporal laser pulse design for material processing on ultrafast scales

    Science.gov (United States)

    Stoian, R.; Colombier, J. P.; Mauclair, C.; Cheng, G.; Bhuyan, M. K.; Velpula, P. K.; Srisungsitthisunti, P.

    2014-01-01

    The spatio-temporal design of ultrafast laser excitation can have a determinant influence on the physical and engineering aspects of laser-matter interactions, with the potential of upgrading laser processing effects. Energy relaxation channels can be synergetically stimulated as the energy delivery rate is synchronized with the material response on ps timescales. Experimental and theoretical loops based on the temporal design of laser irradiation and rapid monitoring of irradiation effects are, therefore, able to predict and determine ideal optimal laser pulse forms for specific ablation objectives. We illustrate this with examples on manipulating the thermodynamic relaxation pathways impacting the ablation products and nanostructuring of bulk and surfaces using longer pulse envelopes. Some of the potential control factors will be pointed out. At the same time the spatial character can dramatically influence the development of laser interaction. We discuss spatial beam engineering examples such as parallel and non-diffractive approaches designed for high-throughput, high-accuracy processing events.

  15. Influence of laser pulse frequency on the microstructure of aluminum nitride thin films synthesized by pulsed laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Antonova, K., E-mail: krasa@issp.bas.bg [Institute of Solid State Physics, Bulgarian Academy of Sciences, Tzarigradsko Chaussee 72, Sofia 1784 (Bulgaria); Duta, L. [National Institute for Lasers, Plasma, and Radiation Physics, 409 Atomistilor Street, 077125 Magurele (Romania); Szekeres, A. [Institute of Solid State Physics, Bulgarian Academy of Sciences, Tzarigradsko Chaussee 72, Sofia 1784 (Bulgaria); Stan, G.E. [National Institute of Materials Physics, 105 bis Atomistilor Street, 077125 Magurele (Romania); Mihailescu, I.N. [National Institute for Lasers, Plasma, and Radiation Physics, 409 Atomistilor Street, 077125 Magurele (Romania); Anastasescu, M.; Stroescu, H.; Gartner, M. [Institute of Physical Chemistry, “Ilie Murgulescu”, Romanian Academy, 202 Splaiul Independentei, 060021 Bucharest (Romania)

    2017-02-01

    Highlights: • Study of pulsed laser deposited AlN films at different laser pulse frequencies. • Higher laser pulse frequency promotes nanocrystallites formation at temperature 450 °C. • AFM and GIXRD detect randomly oriented wurtzite AlN structures. • Characterization of the nanocrystallites’ orientation by FTIR reflectance spectra. • Berreman effect is registered in p-polarised radiation at large incidence angles. - Abstract: Aluminum Nitride (AlN) thin films were synthesized on Si (100) wafers at 450 °C by pulsed laser deposition. A polycrystalline AlN target was multipulsed irradiated in a nitrogen ambient, at different laser pulse repetition rate. Grazing Incidence X-Ray Diffraction and Atomic Force Microscopy analyses evidenced nanocrystallites with a hexagonal lattice in the amorphous AlN matrix. The thickness and optical constants of the layers were determined by infrared spectroscopic ellipsometry. The optical properties were studied by Fourier Transform Infrared reflectance spectroscopy in polarised oblique incidence radiation. Berreman effect was observed around the longitudinal phonon modes of the crystalline AlN component. Angular dependence of the A{sub 1}LO mode frequency was analysed and connected to the orientation of the particles’ optical axis to the substrate surface normal. The role of the laser pulse frequency on the layers’ properties is discussed on this basis.

  16. Dynamic features of bubble induced by a nanosecond pulse laser in still and flowing water

    Science.gov (United States)

    Charee, Wisan; Tangwarodomnukun, Viboon

    2018-03-01

    Underwater laser ablation techniques have been developed and employed to synthesis nanoparticles, to texture workpiece surface and to assist the material removal in laser machining process. However, the understanding of laser-material-water interactions, bubble formation and effects of water flow on ablation performance has still been very limited. This paper thus aims at exploring the formation and collapse of bubbles during the laser ablation of silicon in water. The effects of water flow rate on bubble formation and its consequences to the laser disturbance and cut features obtained in silicon were observed by using a high speed camera. A nanosecond pulse laser emitting the laser pulse energy of 0.2-0.5 mJ was employed in the experiment. The results showed that the bubble size was found to increase with the laser pulse energy. The use of high water flow rate can importantly facilitate the ejection of ablated particles from the workpiece surface, hence resulting in less deposition to the work surface and minimizing any disturbance to the laser beam during the ablation in water. Furthermore, a clean micro-groove in silicon wafer can successfully be produced when the process was performed in the high water flow rate condition. The findings of this study could provide an essential guideline for process selection, control and improvement in the laser micro-/submicro-fabrication using the underwater technique.

  17. Autocorrelation measurement of fast electron pulses emitted through the interaction of femtosecond laser pulses with a solid target.

    Science.gov (United States)

    Inoue, Shunsuke; Tokita, Shigeki; Otani, Kazuto; Hashida, Masaki; Hata, Masayasu; Sakagami, Hitoshi; Taguchi, Toshihiro; Sakabe, Shuji

    2012-11-02

    We report the first direct measurement of the emission duration of laser-accelerated fast electrons from the surface of a solid target irradiated by a high-intensity femtosecond laser pulse. The emission duration is determined by autocorrelation measurement using the Coulomb repulsive forces that act on two equivalent electron pulses. The emission duration depends on the laser pulse duration for laser pulses of 200-690 fs. Numerical modeling of three-dimensional charged particle dynamics indicates that the emission duration of fast electrons is almost equal to the duration of the laser pulse.

  18. Effect of laser pulse duration on damage to metal mirrors for laser IFE

    Science.gov (United States)

    Pulsifer, John E.; Tillack, Mark S.; Harilal, S. S.

    2008-01-01

    A Grazing Incidence Metal Mirror (GIMM) is a chief candidate for beam delivery for Inertial Fusion Energy (IFE). The goal for GIMM survival is greater than 3×10 8 laser pulses with 5 J/cm2 laser fluence normal to the incident beam. Laser-induced damage to metal mirrors is primarily a thermomechanical process. Long-term exposure leads to microstructural evolution analogous to fatigue. We have performed laser-induced damage experiments on high damage threshold aluminum mirrors using commercial KrF excimer (248 nm) lasers. We have studied mirror response to standard, 25 ns long-pulses as well as to IFE prototypic, 5 ns short-pulses achieved using a Pockels Cell. Short-pulse damage fluence was found to be better than predicted using simple thermal diffusion scaling from long-pulse results.

  19. Mechanism study of skin tissue ablation by nanosecond laser pulses

    Science.gov (United States)

    Fang, Qiyin

    Understanding the fundamental mechanisms in laser tissue ablation is essential to improve clinical laser applications by reducing collateral damage and laser pulse energy requirement. The motive of this dissertation is to study skin tissue ablation by nanosecond laser pulses in a wide spectral region from near-infrared to ultraviolet for a clear understanding of the mechanism that can be used to improve future design of the pulsed lasers for dermatology and plastic surgery. Multiple laser and optical configurations have been constructed to generate 9 to 12ns laser pulses with similar profiles at 1064. 532, 266 and 213nm for this study of skin tissue ablation. Through measurements of ablation depth as a function cf laser pulse energy, the 589nm spectral line in the secondary radiation from ablated skin tissue samples was identified as the signature of the occurrence of ablation. Subsequently, this spectral signature has been used to investigate the probabilistic process of the ablation near the threshold at the four wavelengths. Measurements of the ablation probability were conducted as a function of the electrical field strength of the laser pulse and the ablation thresholds in a wide spectral range from 1064nm to 213nm were determined. Histology analysis and an optical transmission method were applied in assessing of the ablation depth per pulse to study the ablation process at irradiance levels higher than threshold. Because more than 70% of the wet weight of the skin tissue is water, optical breakdown and backscattering in water was also investigated along with a nonlinear refraction index measurement using a z-scan technique. Preliminary studies on ablation of a gelatin based tissue phantom are also reported. The current theoretical models describing ablation of soft tissue ablation by short laser pulses were critically reviewed. Since none of the existing models was found capable of explaining the experimental results, a new plasma-mediated model was developed

  20. Development of pulse laser processing for mounting fiber Bragg grating

    Science.gov (United States)

    Nishimura, Aikihko; Shimada, Yukihiro; Yonemoto, Yukihiro; Suzuki, Hirokazu; Ishibashi, Hisayoshi

    2012-07-01

    Pulse laser processing has been developed for the application of industrial plants in monitoring and maintenance. Surface cleaning by nano-second laser ablation was demonstrated for decontamination of oxide layers of Cr contained steel. Direct writing by femtosecond processing induced a Bragg grating in optical fiber to make it a seismic sensor for structural health monitoring. Adhesive cement was used to fix the seismic sensor on the surface of reactor coolant pipe material. Pulse laser processing and its related technologies were presented to overcome the severe accidents of nuclear power plants.

  1. Interaction physics of multipicosecond Petawatt laser pulses with overdense plasma.

    Science.gov (United States)

    Kemp, A J; Divol, L

    2012-11-09

    We study the interaction of intense petawatt laser pulses with overdense plasma over several picoseconds, using two- and three-dimensional kinetic particle simulations. Sustained irradiation with non-diffraction-limited pulses at relativistic intensities yields conditions that differ qualitatively from what is experimentally available today. Nonlinear saturation of laser-driven density perturbations at the target surface causes recurrent emissions of plasma, which stabilize the surface and keep absorption continuously high. This dynamics leads to the acceleration of three distinct groups of electrons up to energies many times the laser ponderomotive potential. We discuss their energy distribution for applications like the fast-ignition approach to inertial confinement fusion.

  2. Xenon plasma sustained by pulse-periodic laser radiation

    Energy Technology Data Exchange (ETDEWEB)

    Rudoy, I. G.; Solovyov, N. G.; Soroka, A. M.; Shilov, A. O.; Yakimov, M. Yu., E-mail: yakimov@lantanlaser.ru [Russian Academy of Sciences, A. Ishlinsky Institute for Problems in Mechanics (Russian Federation)

    2015-10-15

    The possibility of sustaining a quasi-stationary pulse-periodic optical discharge (POD) in xenon at a pressure of p = 10–20 bar in a focused 1.07-μm Yb{sup 3+} laser beam with a pulse repetition rate of f{sub rep} ⩾ 2 kHz, pulse duration of τ ⩾ 200 μs, and power of P = 200–300 W has been demonstrated. In the plasma development phase, the POD pulse brightness is generally several times higher than the stationary brightness of a continuous optical discharge at the same laser power, which indicates a higher plasma temperature in the POD regime. Upon termination of the laser pulse, plasma recombines and is then reinitiated in the next pulse. The initial absorption of laser radiation in successive POD pulses is provided by 5p{sup 5}6s excited states of xenon atoms. This kind of discharge can be applied in plasma-based high-brightness broadband light sources.

  3. Flexible rectangular wave-breaking-free pulse generation in actively mode-locked ytterbium-doped fiber laser.

    Science.gov (United States)

    Chen, He; Chen, Sheng-Ping; Jiang, Zong-Fu; Hou, Jing

    2014-11-03

    We demonstrate nanosecond scale rectangular wave-breaking-free pulse generation in an actively mode locked Yb-doped fiber laser based on a combined action of active periodic cavity loss modulation and nonlinear polarization rotation effect. The pulse width of the laser can be controlled in the range of 890 ps to above 124 ns instantaneously by adjusting the electrical signal applied on the modulator. As high as 19.8 nJ wave-breaking-free pulse is achieved with maximum available pump power. The output pulse temporal dynamics exhibit various distinct characteristics under different modulation and polarization control. The laser presents unusually flexible tunabilities in pulse width, pulse energy and pulse shape.

  4. The efficiency of photovoltaic cells exposed to pulsed laser light

    Science.gov (United States)

    Lowe, R. A.; Landis, G. A.; Jenkins, P.

    1993-01-01

    Future space missions may use laser power beaming systems with a free electron laser (FEL) to transmit light to a photovoltaic array receiver. To investigate the efficiency of solar cells with pulsed laser light, several types of GaAs, Si, CuInSe2, and GaSb cells were tested with the simulated pulse format of the induction and radio frequency (RF) FEL. The induction pulse format was simulated with an 800-watt average power copper vapor laser and the RF format with a frequency-doubled mode-locked Nd:YAG laser. Averaged current vs bias voltage measurements for each cell were taken at various optical power levels and the efficiency measured at the maximum power point. Experimental results show that the conversion efficiency for the cells tested is highly dependent on cell minority carrier lifetime, the width and frequency of the pulses, load impedance, and the average incident power. Three main effects were found to decrease the efficiency of solar cells exposed to simulated FEL illumination: cell series resistance, LC 'ringing', and output inductance. Improvements in efficiency were achieved by modifying the frequency response of the cell to match the spectral energy content of the laser pulse with external passive components.

  5. The interaction of intense subpicosecond laser pulses with underdense plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Coverdale, Christine Ann [Univ. of California, Davis, CA (United States)

    1995-05-11

    Laser-plasma interactions have been of interest for many years not only from a basic physics standpoint, but also for their relevance to numerous applications. Advances in laser technology in recent years have resulted in compact laser systems capable of generating (psec), 1016 W/cm2 laser pulses. These lasers have provided a new regime in which to study laser-plasma interactions, a regime characterized by Lplasma ≥ 2LRayleigh > cτ. The goal of this dissertation is to experimentally characterize the interaction of a short pulse, high intensity laser with an underdense plasma (no ≤ 0.05ncr). Specifically, the parametric instability known as stimulated Raman scatter (SRS) is investigated to determine its behavior when driven by a short, intense laser pulse. Both the forward Raman scatter instability and backscattered Raman instability are studied. The coupled partial differential equations which describe the growth of SRS are reviewed and solved for typical experimental laser and plasma parameters. This solution shows the growth of the waves (electron plasma and scattered light) generated via stimulated Raman scatter. The dispersion relation is also derived and solved for experimentally accessible parameters. The solution of the dispersion relation is used to predict where (in k-space) and at what frequency (in ω-space) the instability will grow. Both the nonrelativistic and relativistic regimes of the instability are considered.

  6. Laser High-Cycle Thermal Fatigue of Pulse Detonation Engine Combustor Materials Tested

    Science.gov (United States)

    Zhu, Dong-Ming; Fox, Dennis S.; Miller, Robert A.

    2001-01-01

    Pulse detonation engines (PDE's) have received increasing attention for future aerospace propulsion applications. Because the PDE is designed for a high-frequency, intermittent detonation combustion process, extremely high gas temperatures and pressures can be realized under the nearly constant-volume combustion environment. The PDE's can potentially achieve higher thermodynamic cycle efficiency and thrust density in comparison to traditional constant-pressure combustion gas turbine engines (ref. 1). However, the development of these engines requires robust design of the engine components that must endure harsh detonation environments. In particular, the detonation combustor chamber, which is designed to sustain and confine the detonation combustion process, will experience high pressure and temperature pulses with very short durations (refs. 2 and 3). Therefore, it is of great importance to evaluate PDE combustor materials and components under simulated engine temperatures and stress conditions in the laboratory. In this study, a high-cycle thermal fatigue test rig was established at the NASA Glenn Research Center using a 1.5-kW CO2 laser. The high-power laser, operating in the pulsed mode, can be controlled at various pulse energy levels and waveform distributions. The enhanced laser pulses can be used to mimic the time-dependent temperature and pressure waves encountered in a pulsed detonation engine. Under the enhanced laser pulse condition, a maximum 7.5-kW peak power with a duration of approximately 0.1 to 0.2 msec (a spike) can be achieved, followed by a plateau region that has about one-fifth of the maximum power level with several milliseconds duration. The laser thermal fatigue rig has also been developed to adopt flat and rotating tubular specimen configurations for the simulated engine tests. More sophisticated laser optic systems can be used to simulate the spatial distributions of the temperature and shock waves in the engine. Pulse laser high

  7. Long-term effects of pulsed high-intensity laser therapy in the treatment of post-burn pruritus: a double-blind, placebo-controlled, randomized study.

    Science.gov (United States)

    Ebid, Anwar Abdelgayed; Ibrahim, Abeer Ramadan; Omar, Mohammed Taher; El Baky, Amal Mohamed Abd

    2017-04-01

    We assessed the long-term effects of pulsed high-intensity laser therapy (HILT) in post-burn pruritus treatment. A total of 49 adult burn patients with mean age of 31.53 ± 10.14 years participated, with 24 patients randomly assigned to the active laser group (ALG) and 25 in the placebo laser group (PLG). The ALG received HILT three times per week for 6 weeks, while the PLG received placebo HILT. Both groups received 10-mg cetirizine tablets twice daily and 10 mg at bedtime. All patients were advised to massage their burn scars with coconut oil for 5 min four times daily. The outcomes measured were the itch severity scale (ISS), impairment of pruritus-related quality of life (QoL), pain level by the visual analog scale (VAS), hand grip strength by handheld dynamometer, and daily cetirizine intake. Repeated-measures ANOVA was used to compare the baseline and post-treatment measurements and after 12 weeks of follow-up. Statistical significance was set at P < 0.05. ISS decreased significantly in the ALG after 6 weeks of treatment and after 12 weeks of follow-up compared with the PLG. The QoL results showed a significant improvement in the ALG compared with the PLG, which continued after 12 weeks. VAS results significantly decrease, hand grip strength significantly improved, and cetirizine intake significantly decreased post-treatment in the ALG relative to the PLG. HILT combined with cetirizine seems more effective in patients with post-burn pruritus than a placebo laser procedure with cetirizine.

  8. High stability breakdown of noble gases with femtosecond laser pulses.

    Science.gov (United States)

    Heins, A M; Guo, Chunlei

    2012-02-15

    In the past, laser-induced breakdown spectroscopy (LIBS) signals have been reported to have a stability independent of the pulse length in solids. In this Letter, we perform the first stability study of femtosecond LIBS in gases (to our best knowledge) and show a significant improvement in signal stability over those achieved with longer pulses. Our study shows that ultrashort-pulse LIBS has an intrinsically higher stability in gas compared to nanosecond-pulse LIBS because of a deterministic ionization process at work in the femtosecond pulse. Relative standard deviations below 1% are demonstrated and are likely only limited by our laser output fluctuations. This enhanced emission stability may open up possibilities for a range of applications, from monitoring rapid gas dynamics to high-quality broadband light sources.

  9. Laser modification of silica, simulating pulse shape and length

    Energy Technology Data Exchange (ETDEWEB)

    Corrales, L. Rene [Departments of Materials Science and Engineering, and Chemistry, University of Arizona, Tucson, Arizona 85721 (United States)], E-mail: lrcorral@email.arizona.edu; Moore, Emily [Departments of Materials Science and Engineering, and Chemistry, University of Arizona, Tucson, Arizona 85721 (United States)

    2009-09-15

    Computer simulations of instantaneous thermal heating due to a laser pulse is modeled as a pulse occurring over 1 or 100 fs, during which time the atoms within a cylinder are given excess kinetic energy to mimic the effect of adding energy locally to a system by a laser. The response of the material under conditions in which a similar amount of energy is dumped within 1 fs versus over a 100 fs pulse with two distinct shapes, square and Gaussian-like, is explored. Key physics disclosed is that with a pulse width of 100 fs, as the energy is being added it begins to dissipate away from region where it is added. With a 1 fs (instantaneous) pulse there is greater initial ballistic behavior than when it is dumped over a 100 fs period. In the latter, there are localized hot spots displaying ballistic behavior.

  10. 100J Pulsed Laser Shock Driver for Dynamic Compression Research

    Science.gov (United States)

    Wang, X.; Sethian, J.; Bromage, J.; Fochs, S.; Broege, D.; Zuegel, J.; Roides, R.; Cuffney, R.; Brent, G.; Zweiback, J.; Currier, Z.; D'Amico, K.; Hawreliak, J.; Zhang, J.; Rigg, P. A.; Gupta, Y. M.

    2017-06-01

    Logos Technologies and the Laboratory for Laser Energetics (LLE, University of Rochester) - in partnership with Washington State University - have designed, built and deployed a one of a kind 100J pulsed UV (351 nm) laser system to perform real-time, x-ray diffraction and imaging experiments in laser-driven compression experiments at the Dynamic Compression Sector (DCS) at the Advanced Photon Source, Argonne National Laboratory. The laser complements the other dynamic compression drivers at DCS. The laser system features beam smoothing for 2-d spatially uniform loading of samples and four, highly reproducible, temporal profiles (total pulse duration: 5-15 ns) to accommodate a wide variety of scientific needs. Other pulse shapes can be achieved as the experimental needs evolve. Timing of the laser pulse is highly precise (<200 ps) to allow accurate synchronization of the x-rays with the dynamic compression event. Details of the laser system, its operating parameters, and representative results will be presented. Work supported by DOE/NNSA.

  11. Laser-pulsed Plasma Chemistry: Laser-initiated Plasma Oxidation Of Niobium

    OpenAIRE

    Marks R.F.; Pollak R.A.; Avouris Ph.; Lin C.T.; Thefaine Y.J.

    1983-01-01

    We report the first observation of the chemical modification of a solid surface exposed to an ambient gas plasma initiated by the interaction of laser radiation with the same surface. A new technique, which we designate laser-pulsed plasma chemistry (LPPC), is proposed for activating heterogeneous chemical reactions at solid surfaces in a gaseous ambient by means of a plasma initiated by laser radiation. Results for niobium metal in one atmosphere oxygen demonstrate single-pulse, self-limitin...

  12. Laser photoionization of triacetone triperoxide (TATP) by femtosecond and nanosecond laser pulses

    Science.gov (United States)

    Mullen, Christopher; Huestis, David; Coggiola, Michael; Oser, Harald

    2006-05-01

    Laser ionization time-of-flight mass spectrometry has been applied to the study of triacetone triperoxide (TATP), an improvised explosive. Wavelength dependent mass spectra in two time regimes were acquired using nanosecond (5 ns) and femtosecond (130 fs) laser pulses. We find the major difference between the two time regimes to be the detection of the parent molecular ion when femtosecond laser pulses are employed.

  13. Pulsed Single Frequency MOPA Laser Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Latest advances in semiconductor optoelectronics makes it possible to develop compact light weight robust sources of coherent optical pulses, demanded for numerous...

  14. Pulse energy control through dual loop electronic feedback

    CSIR Research Space (South Africa)

    Jacobs, Cobus

    2006-07-01

    Full Text Available What is Pulse Energy Control: • Reliability & Repeatability • Accuracy & Stability • Programmability head2righthead2rightWhy do we need it: • Protection against component & subject damage • Micromachining with irregular pulse rate • Safer/improved laser....0 20.0 25.0 30.0 35.0 40.0 45.0 50.0 Q-switched Pulse Repetition Rate [Hz] P u l s e E n e r g y [ m J ] Sources of Instability Reliability & Repeatability Programmability Reliability & Repeatability Accuracy & Stability Pump...

  15. Burst train generator of high energy femtosecond laser pulses for driving heat accumulation effect during micromachining.

    Science.gov (United States)

    Rezaei, Saeid; Li, Jianzhao; Herman, Peter R

    2015-05-01

    A new method for generating high-repetition-rate (12.7-38.2 MHz) burst trains of femtosecond laser pulses has been demonstrated for the purpose of tailoring ultrashort laser interactions in material processing that can harness the heat accumulation effect among pulses separated by a short interval (i.e., 26 ns). Computer-controlled time delays were applied to synchronously trigger the high frequency switching of a high voltage Pockels cell to specify distinctive values of polarization rotation for each round-trip of a laser pulse cycling within a passive resonator. Polarization dependent output coupling facilitated the flexible shaping of the burst envelope profile to provide burst trains of up to ∼1  mJ of burst energy divided over a selectable number (1 to 25) of pulses. Individual pulses of variable energy up to 150 μJ and with pulse duration tunable over 70 fs to 2 ps, were applied in burst trains to generate deep and high aspect ratio holes that could not form with low-repetition-rate laser pulses.

  16. COMPLIS: COllinear spectroscopy Measurements using a Pulsed Laser Ion Source

    CERN Multimedia

    2002-01-01

    A Pulsed Laser spectroscopy experiment has been installed for the study of hyperfine structure and isotope shift of refractory and daughter elements from ISOLDE beams. It includes decelerated ion-implantation, element-selective laser ionization, magnetic and time-of-flight mass separation. The laser spectroscopy has been performed on the desorbed atoms in a set-up at ISOLDE-3 but later on high resolution laser collinear spectroscopy with the secondary pulsed ion beam is planned for the Booster ISOLDE set-up. During the first operation time of ISOLDE-3 we restricted our experiments to Doppler-limited resonant ionization laser and $\\gamma$-$\\gamma$ nuclear spectroscopy on neutron deficient platinum isotopes of even mass number down to A~=~186 and A~=~179 respectively. These isotopes have been produced by implantation of radioactive Hg and their subsequent $\\beta$-decay.

  17. Pathogen reduction in human plasma using an ultrashort pulsed laser.

    Science.gov (United States)

    Tsen, Shaw-Wei D; Kingsley, David H; Kibler, Karen; Jacobs, Bert; Sizemore, Sara; Vaiana, Sara M; Anderson, Jeanne; Tsen, Kong-Thon; Achilefu, Samuel

    2014-01-01

    Pathogen reduction is a viable approach to ensure the continued safety of the blood supply against emerging pathogens. However, the currently licensed pathogen reduction techniques are ineffective against non-enveloped viruses such as hepatitis A virus, and they introduce chemicals with concerns of side effects which prevent their widespread use. In this report, we demonstrate the inactivation of both enveloped and non-enveloped viruses in human plasma using a novel chemical-free method, a visible ultrashort pulsed laser. We found that laser treatment resulted in 2-log, 1-log, and 3-log reductions in human immunodeficiency virus, hepatitis A virus, and murine cytomegalovirus in human plasma, respectively. Laser-treated plasma showed ≥70% retention for most coagulation factors tested. Furthermore, laser treatment did not alter the structure of a model coagulation factor, fibrinogen. Ultrashort pulsed lasers are a promising new method for chemical-free, broad-spectrum pathogen reduction in human plasma.

  18. Pathogen reduction in human plasma using an ultrashort pulsed laser.

    Directory of Open Access Journals (Sweden)

    Shaw-Wei D Tsen

    Full Text Available Pathogen reduction is a viable approach to ensure the continued safety of the blood supply against emerging pathogens. However, the currently licensed pathogen reduction techniques are ineffective against non-enveloped viruses such as hepatitis A virus, and they introduce chemicals with concerns of side effects which prevent their widespread use. In this report, we demonstrate the inactivation of both enveloped and non-enveloped viruses in human plasma using a novel chemical-free method, a visible ultrashort pulsed laser. We found that laser treatment resulted in 2-log, 1-log, and 3-log reductions in human immunodeficiency virus, hepatitis A virus, and murine cytomegalovirus in human plasma, respectively. Laser-treated plasma showed ≥70% retention for most coagulation factors tested. Furthermore, laser treatment did not alter the structure of a model coagulation factor, fibrinogen. Ultrashort pulsed lasers are a promising new method for chemical-free, broad-spectrum pathogen reduction in human plasma.

  19. Study of laser die release by Q-switched Nd:YAG laser pulses

    NARCIS (Netherlands)

    Karlitskaya, N.; de Lange, D.F.; Meijer, J.; Sanders, Rene; Phipps, Claude R.

    2004-01-01

    A new laser-assisted process called "Laser Die Transfer" is developed for high speed assembling of miniature electronic components. Silicon dies, fabricated on an optically transparent carrier are released using a laser pulse. This process has the potential to offer major advantages compared to

  20. LASER ABLATION OF MONOCRYSTALLINE SILICON UNDER PULSED-FREQUENCY FIBER LASER

    Directory of Open Access Journals (Sweden)

    V. P. Veiko

    2015-05-01

    Full Text Available Subject of research. The paper deals with research of the surface ablation for single-crystal silicon wafers and properties of materials obtained in response to silicon ablation while scanning beam radiation of pulse fiber ytterbium laser with a wavelenght λ = 1062 nm in view of variation of radiation power and scanning modes. Method. Wafers of commercial p-type conductivity silicon doped with boron (111, n-type conductivity silicon doped with phosphorus (100 have been under research with a layer of intrinsical silicon oxide having the thickness equal to several 10 s of nanometers and SiO2 layer thickness from 120 to 300 nm grown by thermal oxidation method. The learning system comprises pulse fiber ytterbium laser with a wavelenght λ = 1062 nm. The laser rated-power output is equal to 20 W, pulse length is 100 ns. Pulses frequency is in the range from 20 kHz to 100 kHz. Rated energy in the pulse is equal to 1.0 mJ. Scanning has been carried out by means of two axial scanning device driven by VM2500+ and controlled by personal computer with «SinMarkТМ» software package. Scanning velocity is in the range from 10 mm/s to 4000 mm/s, the covering varies from 100 lines per mm to 3000 lines per mm. Control of samples has been carried out by means of Axio Imager A1m optical microscope Carl Zeiss production with a high definition digital video camera. All experiments have been carried out in the mode of focused laser beam with a radiation spot diameter at the substrate equal to 50 μm. The change of temperature and its distribution along the surface have been evaluated by FLIR IR imager of SC7000 series. Main results. It is shown that ablation occurs without silicon melting and with plasma torch origination. The particles of ejected silicon take part in formation of silicon ions plasma and atmosphere gases supporting the plasmo-chemical growth of SiO2. The range of beam scanning modes is determined where the growth of SiO2 layer is observed

  1. Shallow hydroxyapatite coatings pulsed laser deposited onto Al{sub 2}O{sub 3} substrates with controlled porosity: correlation of morphological characteristics with in vitro testing results

    Energy Technology Data Exchange (ETDEWEB)

    Sima, F.; Ristoscu, C.; Stefan, N.; Dorcioman, G. [National Institute for Lasers, Plasma, and Radiation Physics, PO Box MG-54, RO-77125 Bucharest-Magurele (Romania); Mihailescu, I.N. [National Institute for Lasers, Plasma, and Radiation Physics, PO Box MG-54, RO-77125 Bucharest-Magurele (Romania)], E-mail: ion.mihailescu@inflpr.ro; Sima, L.E.; Petrescu, S.M. [Institute of Biochemistry, Romanian Academy, Splaiul Independentei 296, Bucharest (Romania); Palcevskis, E.; Krastins, J.; Zalite, I. [Institute of Inorganic Chemistry of the Riga Technical University, 34 Miera str, Salaspils LV-2169 (Latvia)

    2009-03-01

    We studied the influence of porous Al{sub 2}O{sub 3} substrates on Ce-stabilized ZrO{sub 2}-doped hydroxyapatite thin films morphology pulsed laser deposited on their top. The porosities of substrates were monitored by changing sintering temperatures and measured with a high pressure Hg porosimeter. The depositions were conducted in 50 Pa water vapors by multipulse ablation of the targets with an UV KrF* ({lambda} = 248 nm, {tau} {approx} 25 ns) excimer laser. The surface morphology of synthesized nanostructures was investigated by scanning electron microscopy and atomic force microcopy. Ca/P ratio within the range 1.67-1.70 was found for hydroxyapatite coatings by energy dispersive spectroscopy. The films were further seeded with mesenchymal stem cells for in vitro tests. The cells showed good attachment and spreading uniformly covering the entire surface of samples. The complexity of film morphology which is increasing with substrate porosity was shown to have a positive influence on cultivated cells density.

  2. Plasma mediated ablation of biological tissues with ultrashort laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Oraevsky, A.A. [Lawrence Livermore National Lab., CA (United States)]|[Rice Univ., Houston, TX (United States). Dept. of Electrical Engineering; DaSilva, L.B.; Feit, M.D. [Lawrence Livermore National Lab., CA (United States)] [and others

    1995-03-08

    Plasma mediated ablation of collagen gels and porcine cornea was studied at various laser pulse durations in the range from 350 fs to 1 ns at 1,053 nm wavelength. A time resolved stress detection technique was employed to measure transient stress profiles and amplitudes. Optical microscopy was used to characterize ablation craters qualitatively, while a wide band acoustic transducer helped to quantify tissue mechanical response and the ablation threshold. The ablation threshold was measured as a function of laser pulse duration and linear absorption coefficient. For nanosecond pulses the ablation threshold was found to have a strong dependence on the linear absorption coefficient of the material. As the pulse length decreased into the subpicosecond regime the ablation threshold became insensitive to the linear absorption coefficient. The ablation efficiency was found to be insensitive to both the laser pulse duration and the linear absorption coefficient. High quality ablation craters with no thermal or mechanical damage to surrounding material were obtained with 350 fs laser pulses. The mechanism of optical breakdown at the tissue surface was theoretically investigated. In the nanosecond regime, optical breakdown proceeds as an electron collisional avalanche ionization initiated by thermal seed electrons. These seed electrons are created by heating of the tissue by linear absorption. In the ultrashort pulse range, optical breakdown is initiated by the multiphoton ionization of the irradiated medium (6 photons in case of tissue irradiated at 1,053 nm wavelength), and becomes less sensitive to the linear absorption coefficient. The energy deposition profile is insensitive to both the laser pulse duration and the linear absorption coefficient.

  3. Electronic beam control for advanced laser radar

    Science.gov (United States)

    Dorschner, Terry A.; Lambert, Larry Q.; Smith, Irl W.; Harris, Clarke E.

    1999-05-01

    The recent development of optical phased arrays (OPAs) enables practical, electronically programmable, control of laser beams for laser radar and other advanced optical sensors. OPAs are the direct analog of microwave phased array antennas; they are electronically programmable optical elements that control the phase distribution on an optical aperture in order to control beam direction and shape. Operating principles and construction of OPAs are briefly described and current and potential performance capabilities are summarized. An OPA supports spatial-domain beam control such as agile or continuous scanning patterns, adaptive electronic focus control, and far-field beam shape control, as well as the generation of multiple beams from a single input beam (pattern generation, or fanout). OPAs also support time-domain beam control, including precision time delay or positioning of short pulses, pulse compression and expansion, and the generation of dense pulse bursts from a single pulse. All of these functions are software controllable, which enables mission-flexible and mission-adaptive optical systems, including so-called 'smart' optical systems with autonomous alignment and calibration capabilities. These and other electronically programmable capabilities are discussed. As a concrete example of an advanced sensor enabled by the OPA, the potential for an adaptable-format, high-resolution, multi-beam laser radar with no moving parts is discussed.

  4. A pulse-burst laser system for Thomson scattering on NSTX-U

    Science.gov (United States)

    Den Hartog, D. J.; Borchardt, M. T.; Holly, D. J.; Diallo, A.; LeBlanc, B.

    2017-10-01

    A pulse-burst laser system has been built for Thomson scattering on NSTX-U, and is currently being integrated into the NSTX-U Thomson scattering diagnostic system. The laser will be operated in three distinct modes. The base mode is continuous 30 Hz rep rate, and is the standard operating mode of the laser. The base mode will be interrupted to produce a "slow burst" (specified 1 kHz rep rate for 50 ms) or a "fast burst" (specified 10 kHz rep rate for 5 ms). The combination of base mode→ interruption→ burst mode is new and has not been implemented on any previous pulse-burst laser system. Laser pulsing is halted for a set period (~ 1 minute) following a burst to allow the YAG rods to cool; this type of operation is called a heat-capacity laser. The laser is Nd:YAG operated at 1064 nm, q-switched to produce >= 1.5 J pulses with ~ 20 ns FWHM. It is flashlamp pumped, with dual-rod oscillator (9 mm) and dual-rod amplifier (12 mm). Variable pulsewidth drive of the flashlamps is accomplished by IGBT (insulated gate bipolar transistor) switching of electrolytic capacitor banks. Direct control of the laser Pockels cell drive enables optimal pulse energy extraction. The laser system has demonstrated compliance with all specifications, and is capable of exceeding design specifications by significant margins, e.g., higher rep rates for longer burst periods. Burst operation of this laser system will be used to capture fast time evolution of the electron temperature and density profiles during events such as ELMs, the L-H transition, and various MHD modes.

  5. Computer modeling of pulsed CO2 lasers for lidar applications

    Science.gov (United States)

    Spiers, Gary D.

    1993-01-01

    The object of this effort is to develop code to enable the accurate prediction of the performance of pulsed transversely excited (TE) CO2 lasers prior to their construction. This is of particular benefit to the NASA Laser Atmospheric Wind Sounder (LAWS) project. A benefit of the completed code is that although developed specifically for the pulsed CO2 laser much of the code can be modified to model other laser systems of interest to the lidar community. A Boltzmann equation solver has been developed which enables the electron excitation rates for the vibrational levels of CO2 and N2, together with the electron ionization and attachment coefficients to be determined for any CO2 laser gas mixture consisting of a combination of CO2, N2, CO, He and CO. The validity of the model has been verified by comparison with published material. The results from the Boltzmann equation solver have been used as input to the laser kinetics code which is currently under development. A numerical code to model the laser induced medium perturbation (LIMP) arising from the relaxation of the lower laser level has been developed and used to determine the effect of LIMP on the frequency spectrum of the LAWS laser output pulse. The enclosed figures show representative results for a laser operating at 0.5 atm. with a discharge cross-section of 4.5 cm to produce a 20 J pulse with aFWHM of 3.1 microns. The first four plots show the temporal evolution of the laser pulse power, energy evolution, LIMP frequency chirp and electric field magnitude. The electric field magnitude is taken by beating the calculated complex electric field and beating it with a local oscillator signal. The remaining two figures show the power spectrum and energy distribution in the pulse as a function of the varying pulse frequency. The LIMP theory has been compared with experimental data from the NOAA Windvan Lidar and has been found to be in good agreement.

  6. Engineering plasmonic nanostructured surfaces by pulsed laser deposition

    Science.gov (United States)

    Ghidelli, Matteo; Mascaretti, Luca; Bricchi, Beatrice Roberta; Zapelli, Andrea; Russo, Valeria; Casari, Carlo Spartaco; Li Bassi, Andrea

    2018-03-01

    The synthesis and the optical response of gold nanoparticles (NPs) and thin nanostructured films grown by pulsed laser deposition (PLD) are here studied. Different PLD process parameters - including background gas pressure and the number of laser shots as well as post-deposition annealing treatments - have been varied to control the growth of Au NPs and films, thus tuning the surface plasmon characteristics. The mechanisms of NPs and film growth have been explored performing a morphological characterization by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM), and the correlation with the optical behavior is investigated. We show that the size distribution and the morphology of the as deposited Au NPs depend on growth mechanisms which are controlled by tuning the deposition process, while the optical behavior is strongly affected by the average size and surface density of NPs or by the length of percolated Au domains. Furthermore, nucleation in gas phase has been reported at high (1000 Pa Ar) background pressures, enabling independent control of NP size and coverage, contrary to surface driven NP growth by diffusion and aggregation on substrate.

  7. Treatment of Acne Vulgaris With Salicylic Acid Chemical Peel and Pulsed Dye Laser: A Split Face, Rater-Blinded, Randomized Controlled Trial.

    Science.gov (United States)

    Lekakh, Olga; Mahoney, Anne Marie; Novice, Karlee; Kamalpour, Julia; Sadeghian, Azeen; Mondo, Dana; Kalnicky, Cathy; Guo, Rong; Peterson, Anthony; Tung, Rebecca

    2015-01-01

    Pulsed dye laser (PDL) has been used to treat acne lesions and scar erythema by interrupting superficial vasculature. Salicylic acid chemical peels are employed chiefly due to their lipophilic, comedolytic, and anti-inflammatory properties. Although studies have looked at peels and laser therapy independently in acne management, we examined these treatments in combination. Our primary objective was to evaluate the safety and efficacy of concurrent use of salicylic acid peels with PDL versus salicylic acid peels alone in the treatment of moderate to severe acne vulgaris. Adult patients with moderate to severe acne were included. Subjects received a total of 3 treatments at 3-week intervals. Per randomized split-face treatment, at week 0, one half of the subject's face was treated with PDL (595 nm) followed by whole face application of a 30% salicylic acid peel. At weeks 3 and 6, the treatments were repeated. At 0 and 9 weeks, patients were assessed with the Global Evaluation Acne (GEA) scale and Dermatology Life Quality Index (DLQI) questionnaire. Nineteen subjects were enrolled, and 18 completed the study. Significant improvement in acne was seen in both the combined (laser and peel) and chemical peel alone treatment arms (P peel only group. Based on the GEA scale scoring, a statistically significant greater difference in acne improvement was seen, from week 0 to week 9, in the combination treatment group compared with the peel only group (P = .003). While acne subjects had significant benefit from the salicylic acid peel alone, they experienced greater significant benefit from PDL treatment used in conjunction with salicylic acid peels. The adjunctive utilization of PDL to salicylic acid peel therapy can lead to better outcomes in acne management.

  8. Free space optical communication based on pulsed lasers

    Science.gov (United States)

    Drozd, Tadeusz; Mierczyk, Zygmunt; Zygmunt, Marek; Wojtanowski, Jacek

    2016-12-01

    Most of the current optical data transmission systems are based on continuous wave (cw) lasers. It results from the tendency to increase data transmission speed, and from the simplicity in implementation (straightforward modulation). Pulsed lasers, which find many applications in a variety of industrial, medical and military systems, in this field are not common. Depending on the type, pulsed lasers can generate instantaneous power which is many times greater when compared with cw lasers. As such, they seem to be very attractive to be used in data transmission technology, especially due to the potentially larger ranges of transmission, or in adverse atmospheric conditions where low power cw-lasersbased transmission is no longer feasible. It is also a very practical idea to implement data transmission capability in the pulsed laser devices that have been around and already used, increasing the functionality of this type of equipment. At the Institute of Optoelectronics at Military University of Technology, a unique method of data transmission based on pulsed laser radiation has been developed. This method is discussed in the paper in terms of both data transmission speed and transmission range. Additionally, in order to verify the theoretical assumptions, modules for voice and data transmission were developed and practically tested which is also reported, including the measurements of Bit Error Rate (BER) and performance vs. range analysis.

  9. Pulsed Nd:YAG laser beam drilling: A review

    Science.gov (United States)

    Gautam, Girish Dutt; Pandey, Arun Kumar

    2018-03-01

    Laser beam drilling (LBD) is one of non contact type unconventional machining process that are employed in machining of stiff and high-strength materials, high strength temperature resistance materials such as; metal alloys, ceramics, composites and superalloys. Most of these materials are difficult-to-machine by using conventional machining methods. Also, the complex and precise holes may not be obtained by using the conventional machining processes which may be obtained by using unconventional machining processes. The laser beam drilling in one of the most important unconventional machining process that may be used for the machining of these materials with satisfactorily. In this paper, the attention is focused on the experimental and theoretical investigations on the pulsed Nd:YAG laser drilling of different categories of materials such as ferrous materials, non-ferrous materials, superalloys, composites and Ceramics. Moreover, the review has been emphasized by the use of pulsed Nd:YAG laser drilling of different materials in order to enhance productivity of this process without adverse effects on the drilled holes quality characteristics. Finally, the review is concluded with the possible scope in the area of pulsed Nd:YAG laser drilling. This review work may be very useful to the subsequent researchers in order to give an insight in the area of pulsed Nd:YAG laser drilling of different materials and research gaps available in this area.

  10. Beamlet pulse-generation and wavefront-control system

    Energy Technology Data Exchange (ETDEWEB)

    Van Wonterghem, B.M.; Salmon, J.T.; Wilcox, R.W.

    1996-06-01

    The Beamlet pulse-generation system (or {open_quotes}front end{close_quotes}) refers to the laser hardware that generates the spatially and temporally shaped pulse that is injected into the main laser cavity. All large ICF lasers have pulse-generation systems that typically consist of a narrow-band oscillator, elector-optic modulators for temporal and bandwidth shaping, and one or more preamplifiers. Temporal shaping is used to provide the desired laser output pulse shape and also to compensate for gain saturation effects in the large-aperture amplifiers. Bandwidth is applied to fulfill specific target irradiation requirements and to avoid stimulated Brillouin scattering (SBS) in large-aperture laser components. Usually the sharp edge of the beam`s spatial intensity profile is apodized before injection in the main amplifier beam line. This prevents large-amplitude ripples on the intensity profile. Here the authors briefly review the front-end design and discuss improvements to the oscillator and modulator systems. Their main focus, however, is to describe Beamlet`s novel beam-shaping and wavefront-control systems that have recently been fully activated and tested.

  11. Precision resection of lung cancer in a sheep model using ultrashort laser pulses

    Science.gov (United States)

    Beck, Rainer J.; Mohanan, Syam Mohan P. C.; Góra, Wojciech S.; Cousens, Chris; Finlayson, Jeanie; Dagleish, Mark P.; Griffiths, David J.; Shephard, Jonathan D.

    2017-02-01

    Recent developments and progress in the delivery of high average power ultrafast laser pulses enable a range of novel minimally invasive surgical procedures. Lung cancer is the leading cause of cancer deaths worldwide and here the resection of lung tumours by means of picosecond laser pulses is presented. This represents a potential alternative to mitigate limitations of existing surgical treatments in terms of precision and collateral thermal damage to the healthy tissue. Robust process parameters for the laser resection are demonstrated using ovine pulmonary adenocarcinoma (OPA). OPA is a naturally occurring lung cancer of sheep caused by retrovirus infection that has several features in common with some forms of human pulmonary adenocarcinoma, including a similar histological appearance, which makes it ideally suited for this study. The picosecond laser was operated at a wavelength of 515 nm to resect square cavities from fresh ex-vivo OPA samples using a range of scanning strategies. Process parameters are presented for efficient ablation of the tumour with clear margins and only minimal collateral damage to the surrounding tissue. The resection depth can be controlled precisely by means of the pulse energy. By adjusting the overlap between successive laser pulses, deliberate heat transfer to the tissue and thermal damage can be achieved. This can be beneficial for on demand haemostasis and laser coagulation. Overall, the application of ultrafast lasers for the resection of lung tumours has potential to enable significantly improved precision and reduced thermal damage to the surrounding tissue compared to conventional techniques.

  12. Time resolved studies of H{sub 2}{sup +} dissociation with phase-stabilized laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, Bettina

    2010-06-23

    In the course of this thesis, experimental studies on the dissociation of H{sub 2}{sup +}(H{sub 2}{sup +}{yields}p+H) in ultrashort laser pulses with a stabilized carrier-envelope phase (CEP) were carried out. In single-pulse measurements, the ability to control the emission direction of low energetic protons, i.e. the localization of the bound electron at one of the nuclei after dissociation, by the CEP was demonstrated. The coincident detection of the emitted protons and electrons and the measurement of their three-dimensional momentum vectors with a reaction microscope allowed to clarify the localization mechanism. Further control was achieved by a pump-control scheme with two timedelayed CEP-stabilized laser pulses. Here the neutral H{sub 2} molecule was ionized in the first pulse and dissociation was induced by the second pulse. Electron localization was shown to depend on the properties of the bound nuclear wave packet in H{sub 2}{sup +} at the time the control pulse is applied, demonstrating the ability to use the shape and dynamics of the nuclear wave packet as control parameters. Wave packet simulations were performed reproducing qualitatively the experimental results of the single and the two-pulse measurements. For both control schemes, intuitive models are presented, which qualitatively explain the main features of the obtained results. (orig.)

  13. A comparative study of pulsed Nd:YAG and CO2 laser effect on cardiovascular tissue

    OpenAIRE

    Yova, D.; Papadakis, E.; Kassis, K.; Agapitos, E.; Kavantzas, N.; Koutsouris, D.; Serafetinidis, A.

    1994-01-01

    Percutaneous laser angioplasty is receiving increasing attention, as laser ablation of atheromatous plaque presents advantages to direct surgery or balloon angioplasty. One of the main prerequisites of using powerful pulsed lasers in angioplasty is the optimum choice of the irradiation parameters (the wavelength, the pulse shape and duration, the energy parameters e.t.c.). Infrared lasers have numerous applications in surgery. Among them the pulsed CO2 laser emitting at 10.6 µm and the pulsed...

  14. A Preliminary In Vitro Study on the Efficacy of High-Power Photodynamic Therapy (HLLT): Comparison between Pulsed Diode Lasers and Superpulsed Diode Lasers and Impact of Hydrogen Peroxide with Controlled Stabilization.

    Science.gov (United States)

    Caccianiga, Gianluigi; Baldoni, Marco; Ghisalberti, Carlo Angelo; Paiusco, Alessio

    2016-01-01

    Aim. In periodontology lasers have been suggested for the photodynamic therapy (PDT): such therapy can be defined as the inactivation of cells, microorganisms, or molecules induced by light and not by heat. The aim of this study was to evaluate results of PDT using a 980 nm diode laser (Wiser Doctor Smile, Lambda SPA, Italy) combined with hydrogen peroxide, comparing a pulsed diode laser (LI) activity to a high-frequency superpulsed diode laser (LII). Materials and Methods. Primary fibroblasts and keratinocytes cell lines, isolated from human dermis, were irradiated every 48 h for 10 days using LI and LII combined with SiOxyL(+) ™ Solution (hydrogen peroxide (HP) stabilized with a glycerol phosphate complex). Two days after the last irradiation, the treated cultures were analyzed by flow cytofluorometry (FACS) and western blotting to quantify keratin 5 and keratin 8 with monoclonal antibodies reactive to cytokeratin 5 and cytokeratin 8. Antimicrobial activity was also evaluated. Results. Both experimental models show the superiority of LII against LI. In parallel, stabilized HP provided better results in the regeneration test in respect to common HP, while the biocidal activity remains comparable. Conclusion. The use of high-frequency lasers combined with stabilized hydrogen peroxide can provide optimal results for a substantial decrease of bacterial count combined with a maximal biostimulation induction of soft tissues and osteogenesis.

  15. A Preliminary In Vitro Study on the Efficacy of High-Power Photodynamic Therapy (HLLT: Comparison between Pulsed Diode Lasers and Superpulsed Diode Lasers and Impact of Hydrogen Peroxide with Controlled Stabilization

    Directory of Open Access Journals (Sweden)

    Gianluigi Caccianiga

    2016-01-01

    Full Text Available Aim. In periodontology lasers have been suggested for the photodynamic therapy (PDT: such therapy can be defined as the inactivation of cells, microorganisms, or molecules induced by light and not by heat. The aim of this study was to evaluate results of PDT using a 980 nm diode laser (Wiser Doctor Smile, Lambda SPA, Italy combined with hydrogen peroxide, comparing a pulsed diode laser (LI activity to a high-frequency superpulsed diode laser (LII. Materials and Methods. Primary fibroblasts and keratinocytes cell lines, isolated from human dermis, were irradiated every 48 h for 10 days using LI and LII combined with SiOxyL+™ Solution (hydrogen peroxide (HP stabilized with a glycerol phosphate complex. Two days after the last irradiation, the treated cultures were analyzed by flow cytofluorometry (FACS and western blotting to quantify keratin 5 and keratin 8 with monoclonal antibodies reactive to cytokeratin 5 and cytokeratin 8. Antimicrobial activity was also evaluated. Results. Both experimental models show the superiority of LII against LI. In parallel, stabilized HP provided better results in the regeneration test in respect to common HP, while the biocidal activity remains comparable. Conclusion. The use of high-frequency lasers combined with stabilized hydrogen peroxide can provide optimal results for a substantial decrease of bacterial count combined with a maximal biostimulation induction of soft tissues and osteogenesis.

  16. Rapid, controllable, one-pot and room-temperature aqueous synthesis of ZnO:Cu nanoparticles by pulsed UV laser and its application for photocatalytic degradation of methyl orange.

    Science.gov (United States)

    Arabi, Mozhgan; Baizaee, Seyyed Mahdy; Bahador, Alireza; Otaqsara, Seyed Mohammad Taheri

    2017-12-28

    Zinc oxide (ZnO) and ZnO:Cu nanoparticles (NPs) were synthesized using a rapid, controllable, one-pot and room-temperature pulsed UV-laser assisted method. UV-laser irradiation was used as an effective energy source in order to gain better control over the NPs size and morphology in aqueous media. Parameters effective in laser assisted synthesis of NPs such as irradiation time and laser shot repetition rate were optimized. Photoluminescence (PL) spectra of ZnO NPs showed a broad emission with two trap state peaks located at 442 and 485 nm related to electronic transition from zinc interstitial level (I Zn ) to zinc vacancy level (V Zn ) and electronic transition from conduction band to the oxygen vacancy level (V O ), respectively. For ZnO:Cu NPs, trap state emissions disappeared completely and a copper (Cu)-related emission appeared. PL intensity of Cu-related emission increased with the increase in concentration of Cu 2+ , so that for molar ratio of Cu:Zn 2%, optimal value of PL intensity was obtained. The photocatalytic activity of Cu-doped ZnO revealed 50 and 100% increasement than that of undoped NPs under UV and visible irradiation, respectively. The enhanced photocatalytic activity could be attributed to smaller crystal size, as well as creation of impurity acceptor levels (T 2 ) inside the ZnO energy band gap. Copyright © 2017 John Wiley & Sons, Ltd.

  17. Energy deposition from focused terawatt laser pulses in air

    CERN Document Server

    Point, Guillaume; Mysyrowicz, André; Houard, Aurélien

    2015-01-01

    Laser filamentation is responsible for the deposition of a significant part of the laser pulse energy in the propagation medium. We found that using terawatt laser pulses and relatively tight focusing conditions in air, resulting in a bundle of co-propagating multifilaments, more than 50 % of the pulses energy is transferred to the medium, eventually degrading into heat. This results in a strong hydrodynamic reaction of air with the generation of shock waves and associated underdense channels for each short-scale filament. In the focal zone, where filaments are close to each other, these discrete channels eventually merge to form a single cylindrical low-density tube over a $\\sim 1~ \\mu\\mathrm{s}$ timescale. We measured the maximum lineic deposited energy to be more than 1 J/m.

  18. Seeded QED cascades in counterpropagating laser pulses.

    Science.gov (United States)

    Grismayer, T; Vranic, M; Martins, J L; Fonseca, R A; Silva, L O

    2017-02-01

    The growth rates of seeded QED cascades in counterpropagating lasers are calculated with first-principles two- and three-dimensional QED-PIC (particle-in-cell) simulations. The dependence of the growth rate on the laser polarization and intensity is compared with analytical models that support the findings of the simulations. The models provide insight regarding the qualitative trend of the cascade growth when the intensity of the laser field is varied. A discussion about the cascade's threshold is included, based on the analytical and numerical results. These results show that relativistic pair plasmas and efficient conversion from laser photons to γ rays can be observed with the typical intensities planned to operate on future ultraintense laser facilities such as ELI or Vulcan.

  19. High power, short pulses ultraviolet laser for the development of a new x-ray laser

    Energy Technology Data Exchange (ETDEWEB)

    Meixler, L.; Nam, C.H.; Robinson, J.; Tighe, W.; Krushelnick, K.; Suckewer, S.; Goldhar, J.; Seely, J.; Feldman, U.

    1989-04-01

    A high power, short pulse ultraviolet laser system (Powerful Picosecond-Laser) has been developed at the Princeton Plasma Physics Laboratory (PPPL) as part of experiments designed to generate shorter wavelength x-ray lasers. With the addition of pulse compression and a final KrF amplifier the laser output is expected to have reached 1/3-1/2 TW (10/sup 12/ watts) levels. The laser system, particularly the final amplifier, is described along with some initial soft x-ray spectra from laser-target experiments. The front end of the PP-Laser provides an output of 20--30 GW (10/sup 9/ watts) and can be focussed to intensities of /approximately/10/sup 16/ W/cm/sup 2/. Experiments using this output to examine the effects of a prepulse on laser-target interaction are described. 19 refs., 14 figs.

  20. Photoionization of water molecules by a train of attosecond pulses assisted by a near-infrared laser: delay and polarization control

    Science.gov (United States)

    Martini, Lara; Boll, Diego I. R.; Fojón, Omar A.

    2017-08-01

    Basic reactions involving water molecules are essential to understand the interaction between radiation and the biological tissue because living cells are composed mostly by water. Therefore, the knowledge of ionization of the latter is crucial in many domains of Biology and Physics. So, we study theoretically the photoionization of water molecules by extreme ultraviolet attopulse trains assisted by lasers in the near-infrared range. We use a separable Coulomb-Volkov model in which the temporal evolution of the system can be divided into three stages allowing spatial and temporal separation for the Coulomb and Volkov final state wavefunctions. First, we analyze photoelectron angular distributions for different delays between the attopulse train and the assistant laser field. We compare our results for water and Ne atoms as they belong to the same isoelectronic series. Moreover, we contrast our calculations with previous theoretical and experimental work for Ar atoms due to the similarities of the orbitals involved in the reaction. Second, we study the effect of varying the relative orientations of the attopulse and laser field polarizations and we compare our predictions with other theories and experiments. We expect these studies contribute to the improvement of polarization experiments and the development of the attopulse trains and assistant laser fields technologies. Finally, we hope our work promote progress on the control of the chemical reactivity of water molecules since this could be useful in different fields such as radiobiology and medical physics.

  1. Numerical analysis of laser ablation and damage in glass with multiple picosecond laser pulses.

    Science.gov (United States)

    Sun, Mingying; Eppelt, Urs; Russ, Simone; Hartmann, Claudia; Siebert, Christof; Zhu, Jianqiang; Schulz, Wolfgang

    2013-04-08

    This study presents a novel numerical model for laser ablation and laser damage in glass including beam propagation and nonlinear absorption of multiple incident ultrashort laser pulses. The laser ablation and damage in the glass cutting process with a picosecond pulsed laser was studied. The numerical results were in good agreement with our experimental observations, thereby revealing the damage mechanism induced by laser ablation. Beam propagation effects such as interference, diffraction and refraction, play a major role in the evolution of the crater structure and the damage region. There are three different damage regions, a thin layer and two different kinds of spikes. Moreover, the electronic damage mechanism was verified and distinguished from heat modification using the experimental results with different pulse spatial overlaps.

  2. Application of laser pulse stretching scheme for efficiently delivering laser energy in photoacoustic imaging

    Science.gov (United States)

    Wang, Tianheng; Kumavor, Patrick D.; Zhu, Quing

    2012-06-01

    High-energy and short-duration laser pulses are desirable to improve the photoacoustic image quality when imaging deeply seated lesions. In many clinical applications, the high-energy pulses are coupled to tissue using optical fibers. These pulses can damage fibers if the damage threshold is exceeded. While keeping the total energy under the Food and Drug Administration limit for avoiding tissue damage, it is necessary to reduce the peak intensity and increase the pulse duration for minimizing fiber damage and delivering sufficient light for imaging. We use laser-pulse-stretching to address this problem. An initial 17-ns pulse was stretched to 27 and 37 ns by a ring-cavity laser-pulse-stretching system. The peak power of the 37-ns stretched pulse reduced to 42% of the original, while the fiber damage threshold was increased by 1.5-fold. Three ultrasound transducers centered at 1.3-, 3.5-, and 6-MHz frequencies were simulated, and the results showed that the photoacoustic signal of a 0.5-mm-diameter target obtained with 37-ns pulse was about 98, 91, and 80%, respectively, using the same energy as the 17-ns pulse. Simulations were validated using a broadband hydrophone. Quantitative comparisons of photoacoustic images obtained with three corresponding transducers showed that the image quality was not affected by stretching the pulse.

  3. Short infrared laser pulses block action potentials in neurons

    Science.gov (United States)

    Walsh, Alex J.; Tolstykh, Gleb P.; Martens, Stacey L.; Ibey, Bennett L.; Beier, Hope T.

    2017-02-01

    Short infrared laser pulses have many physiological effects on cells including the ability to stimulate action potentials in neurons. Here we show that short infrared laser pulses can also reversibly block action potentials. Primary rat hippocampal neurons were transfected with the Optopatch2 plasmid, which contains both a blue-light activated channel rhodopsin (CheRiff) and a red-light fluorescent membrane voltage reporter (QuasAr2). This optogenetic platform allows robust stimulation and recording of action potential activity in neurons in a non-contact, low noise manner. For all experiments, QuasAr2 was imaged continuously on a wide-field fluorescent microscope using a Krypton laser (647 nm) as the excitation source and an EMCCD camera operating at 1000 Hz to collect emitted fluorescence. A co-aligned Argon laser (488 nm, 5 ms at 10Hz) provided activation light for CheRiff. A 200 mm fiber delivered infrared light locally to the target neuron. Reversible action potential block in neurons was observed following a short infrared laser pulse (0.26-0.96 J/cm2; 1.37-5.01 ms; 1869 nm), with the block persisting for more than 1 s with exposures greater than 0.69 J/cm2. Action potential block was sustained for 30 s with the short infrared laser pulsed at 1-7 Hz. Full recovery of neuronal activity was observed 5-30s post-infrared exposure. These results indicate that optogenetics provides a robust platform for the study of action potential block and that short infrared laser pulses can be used for non-contact, reversible action potential block.

  4. Pulsed-Laser Irradiation Space Weathering Of A Carbonaceous Chondrite

    Science.gov (United States)

    Thompson, M. S.; Keller, L. P.; Christoffersen, R.; Loeffler, M. J.; Morris, R. V.; Graff, T. G.; Rahman, Z.

    2017-01-01

    Grains on the surfaces of airless bodies experience irradiation from solar energetic particles and melting, vaporization and recondensation processes associated with micrometeorite impacts. Collectively, these processes are known as space weathering and they affect the spectral properties, composition, and microstructure of material on the surfaces of airless bodies, e.g. Recent efforts have focused on space weathering of carbonaceous materials which will be critical for interpreting results from the OSIRIS-REx and Hayabusa2 missions targeting primitive, organic-rich asteroids. In addition to returned sample analyses, space weathering processes are quantified through laboratory experiments. For example, the short-duration thermal pulse from hypervelocity micrometeorite impacts have been simulated using pulsed-laser irradiation of target material e.g. Recent work however, has shown that pulsed-laser irradiation has variable effects on the spectral properties and microstructure of carbonaceous chondrite samples. Here we investigate the spectral characteristics of pulsed-laser irradiated CM2 carbonaceous chondrite, Murchison, including the vaporized component. We also report the chemical and structural characteristics of specific mineral phases within the meteorite as a result of pulsed-laser irradiation.

  5. Stretching of picosecond laser pulses with uniform reflecting volume Bragg gratings

    Science.gov (United States)

    Mokhov, Sergiy; Spiro, Alexander; Smirnov, Vadim; Kaim, Sergiy; Zeldovich, Boris; Glebov, Leonid

    2017-08-01

    This study shows that a uniform reflecting volume Bragg grating (VBG) can be used as a compact monolithic stretcher of high-power picosecond laser pulses, which is important for cases in which chirped Bragg gratings with the required chirp rate are difficult to fabricate. When an incident short pulse propagates along a grating and experiences local Bragg diffraction, a chirp-free reflected stretched pulse with an almost rectangular shape is generated. The increase in the duration of the reflected pulse is approximately equal to twice the propagation time along the grating. We derive an analytic expression for the diffraction efficiency, which incorporates the incident pulse duration, grating thickness, and amplitude of the refractive index modulation, enabling selection of the optimum grating for pulse stretching. Theoretical models of the extended pulse profiles are found to be in good agreement with experimental autocorrelation measurements. We also propose a simple and reliable method to control the temporal parameters of high-power picosecond pulses using the same laser source and a VBG of variable thickness, which can simplify experiments requiring different pulse durations significantly.

  6. Interaction of nanosecond ultraviolet laser pulses with reactive dusty plasma

    Energy Technology Data Exchange (ETDEWEB)

    Wetering, F. M. J. H. van de; Oosterbeek, W.; Beckers, J.; Nijdam, S. [Eindhoven University of Technology, P.O. Box 513, 5600 MB Eindhoven (Netherlands); Gibert, T.; Mikikian, M.; Rabat, H.; Kovačević, E.; Berndt, J. [GREMI, UMR7344, CNRS & Université d' Orléans, Orléans (France)

    2016-05-23

    Even though UV laser pulses that irradiate a gas discharge are small compared to the plasma volume (≲3%) and plasma-on time (≲6 × 10{sup −6}%), they are found to dramatically change the discharge characteristics on a global scale. The reactive argon–acetylene plasma allows the growth of nanoparticles with diameters up to 1 μm, which are formed inside the discharge volume due to spontaneous polymerization reactions. It is found that the laser pulses predominantly accelerate and enhance the coagulation phase and are able to suppress the formation of a dust void.

  7. Correlated Multielectron Dynamics in Ultrafast Laser Pulse Interactions with Atoms

    Science.gov (United States)

    Rudenko, A.; Zrost, K.; Feuerstein, B.; de Jesus, V. L.; Schröter, C. D.; Moshammer, R.; Ullrich, J.

    2004-12-01

    We present the results of the detailed experimental study of multiple ionization of Ne and Ar by 25 and 7fs laser pulses. Whereas in multiple ionization of Ar different mechanisms, involving field ionization steps and recollision-induced excitations, play a role, for Ne only one channel, where the highly correlated instantaneous emission of up to four electrons is triggered by a recollisional electron impact, is found to be important. Using few-cycle pulses we are able to suppress those processes that occur on time scales longer than one laser cycle.

  8. Plasma high-order-harmonic generation from ultraintense laser pulses

    Science.gov (United States)

    Tang, Suo; Kumar, Naveen; Keitel, Christoph H.

    2017-05-01

    Plasma high-order-harmonic generation from an extremely intense short-pulse laser is explored by including the effects of ion motion, electron-ion collisions, and radiation reaction force in the plasma dynamics. The laser radiation pressure induces plasma ion motion through the hole-boring effect, resulting in frequency shifting and widening of the harmonic spectra. The classical radiation reaction force slightly mitigates the frequency broadening caused by the ion motion. Based on the results and physical considerations, parameter maps highlighting the optimum regions for generating a single intense attosecond pulse and coherent XUV radiation are presented.

  9. Detection of early dental caries with short pulse laser

    Energy Technology Data Exchange (ETDEWEB)

    Okubo, Nahoko; Goto, Shigeru [Osada Research Inst., Ltd., Tokyo (Japan); Tanaka, Hiroshi; Ohzu, Akira; Arisawa, Takashi [Japan Atomic Energy Research Inst., Kansai Research Establishment, Advanced Photon Research Center, Kyoto (Japan)

    2002-07-01

    Differences in the optical properties of polarization and photoluminescence between caries lesion and noncaries (sound) enamel have been investigated by focusing a pulsed Nd:YAG laser of 532 nm on the surface of teeth. Significant difference in the polarization property of the scattered light from the surface can be observed with some carious samples. For photoluminescence spectral lines which appear at around 650 nm, the intensity of caries lesion has been approximately two times higher than that of sound one. A discussion is presented in which early are potentially detectable by the pulsed laser. (author)

  10. Absorption of a laser light pulse in a dense plasma.

    Science.gov (United States)

    Mehlman-Balloffet, G.

    1973-01-01

    An experimental study of the absorption of a laser light pulse in a transient, high-density, high-temperature plasma is presented. The plasma is generated around a metallic anode tip by a fast capacitive discharge occurring in vacuum. The amount of transmitted light is measured for plasmas made of different metallic ions in the regions of the discharge of high electronic density. Variation of the transmission during the laser pulse is also recorded. Plasma electrons are considered responsible for the very high absorption observed.

  11. High-repetition-rate pulse-burst laser for Thomson scattering on the MST reversed-field pinch

    Science.gov (United States)

    Young, W. C.; Morton, L. A.; Parke, E.; Den Hartog, D. J.

    2013-11-01

    A new, high-repetition-rate pulse-burst laser system for the MST Thomson scattering diagnostic has operated with 2 J pulses at repetition rates up to 75 kHz within a burst. The 1064 nm laser currently employs a q-switched, diode pumped Nd:YVO4 master oscillator, four Nd:YAG amplifier stages, and a Nd:glass amplifier, with plans for an additional Nd:glass amplifier. The laser can maintain 1.5-2 J pulses in two operating modes: either at a uniform repetition rate of 5-10 kHz (sustained for 5-8 ms), or reach rates of up to 75 kHz in pulse-burst operation (for 10 bursts of 15 pulses each), limited by flashlamp explosion energy and wall loading. The full system, including an additional Nd:glass amplifier, is designed to produce bursts of 2 J pulses at a repetition rate of at least 250 kHz. Custom programmable square-pulse power supplies drive the amplifier flashlamps, providing fine control of pulse timing, duration, and repetition, and allow for pulse-burst operation. The new laser system integrates with the same collection optics and detectors as used by the previous MST Thomson laser: 21 spatial points across the MST minor radius, filter polychromators with 6 to 8 channels (10 eV-5 keV range), avalanche photodiode detectors, and 1 GSample/s/channel digitization. Use of the previous pulse-burst laser continues concurrently with new laser development. Additional notes on optimization of flashlamp simmering will also be covered, showing that an increase in simmer currents can improve pulse-to-pulse energy consistency on both the new and older lasers.

  12. Relativistic Electron Acceleration with Ultrashort Mid-IR Laser Pulses

    Science.gov (United States)

    Feder, Linus; Woodbury, Daniel; Shumakova, Valentina; Gollner, Claudia; Miao, Bo; Schwartz, Robert; Pugžlys, Audrius; Baltuška, Andrius; Milchberg, Howard

    2017-10-01

    We report the first results of laser plasma wakefield acceleration driven by ultrashort mid-infrared laser pulses (λ = 3.9 μm , pulsewidth 100 fs, energy width, as well as trends in the accelerated beam profiles, charge and energy spectra which are supported by 3D particle-in-cell simulations. These results extend earlier work with sub-TW self-modulated laser wakefield acceleration using near IR drivers to the Mid-IR, and enable us to capture time-resolved images of relativistic self-focusing of the laser pulse. This work supported by DOE (DESC0010706TDD, DESC0015516); AFOSR(FA95501310044, FA95501610121); NSF(PHY1535519); DHS.

  13. Influence of laser pulse frequency on the microstructure of aluminum nitride thin films synthesized by pulsed laser deposition

    Science.gov (United States)

    Antonova, K.; Duta, L.; Szekeres, A.; Stan, G. E.; Mihailescu, I. N.; Anastasescu, M.; Stroescu, H.; Gartner, M.

    2017-02-01

    Aluminum Nitride (AlN) thin films were synthesized on Si (100) wafers at 450 °C by pulsed laser deposition. A polycrystalline AlN target was multipulsed irradiated in a nitrogen ambient, at different laser pulse repetition rate. Grazing Incidence X-Ray Diffraction and Atomic Force Microscopy analyses evidenced nanocrystallites with a hexagonal lattice in the amorphous AlN matrix. The thickness and optical constants of the layers were determined by infrared spectroscopic ellipsometry. The optical properties were studied by Fourier Transform Infrared reflectance spectroscopy in polarised oblique incidence radiation. Berreman effect was observed around the longitudinal phonon modes of the crystalline AlN component. Angular dependence of the A1LO mode frequency was analysed and connected to the orientation of the particles' optical axis to the substrate surface normal. The role of the laser pulse frequency on the layers' properties is discussed on this basis.

  14. SPECTRAL AMPLITUDE AND PHASE EVOLUTION IN PETAWATT LASER PULSES

    Energy Technology Data Exchange (ETDEWEB)

    Filip, C V

    2010-11-22

    The influence of the active gain medium on the spectral amplitude and phase of amplified pulses in a CPA system is studied. Results from a 10-PW example based on Nd-doped mixed glasses are presented. In conclusion, this study shows that, by using spectral shaping and gain saturation in a mixed-glass amplifier, it is possible to produce 124 fs, 1.4 kJ laser pulses. One detrimental effect, the pulse distortion due to resonant amplification medium, has been investigated and its magnitude as well as its compensation calculated.

  15. Theory and Modeling of Petawatt Laser Pulse Propagation in Low Density Plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Shadwick, Bradley A. [Univ. of Nebraska, Lincoln, NE (United States). Dept. of Physics and Astronomy; Kalmykov, S. Y. [Univ. of Nebraska, Lincoln, NE (United States). Dept. of Physics and Astronomy

    2016-12-08

    Report describing accomplishments in all-optical control of self-injection in laser-plasma accelerators and in developing advanced numerical models of laser-plasma interactions. All-optical approaches to controlling electron self-injection and beam formation in laser-plasma accelerators (LPAs) were explored. It was demonstrated that control over the laser pulse evolution is the key ingredient in the generation of low-background, low-phase-space-volume electron beams. To this end, preserving a smooth laser pulse envelope throughout the acceleration process can be achieved through tuning the phase and amplitude of the incident pulse. A negative frequency chirp compensates the frequency red-shift accumulated due to wake excitation, preventing evolution of the pulse into a relativistic optical shock. This reduces the ponderomotive force exerted on quiescent plasma electrons, suppressing expansion of the bubble and continuous injection of background electrons, thereby reducing the charge in the low-energy tail by an order of magnitude. Slowly raising the density in the pulse propagation direction locks electrons in the accelerating phase, boosting their energy, keeping continuous injection at a low level, tripling the brightness of the quasi-monoenergetic component. Additionally, propagating the negatively chirped pulse in a plasma channel suppresses diffraction of the pulse leading edge, further reducing continuous injection. As a side effect, oscillations of the pulse tail may be enhanced, leading to production of low-background, polychromatic electron beams. Such beams, consisting of quasi-monoenergetic components with controllable energy and energy separation, may be useful as drivers of polychromatic x-rays based on Thomson backscattering. These all-optical methods of electron beam quality control are critically important for the development of future compact, high-repetition-rate, GeV-scale LPA using 10 TW-class, ultra-high bandwidth pulses and mm-scale, dense

  16. Dynamics of pulsed holmium:YAG laser photocoagulation of albumen

    Energy Technology Data Exchange (ETDEWEB)

    Pfefer, T.J. [Biomedical Engineering Program, The University of Texas at Austin, Austin, TX 78712 (United States). E-mail: jpfefer at helix.mgh.harvard.edu; Chan, K.F.; Hammer, D.X. [Department of Electrical and Computer Engineering, The University of Texas at Austin, Austin, TX 78712 (United States); Welch, A.J. [Biomedical Engineering Program, The University of Texas at Austin, Austin, TX 78712 (United States); Department of Electrical and Computer Engineering, The University of Texas at Austin, Austin, TX 78712 (United States)

    2000-05-01

    The pulsed holmium:YAG laser ({lambda} = 2.12 {mu}m, {tau}{sub p} = 250 {mu}s) has been investigated as a method for inducing localized coagulation for medical procedures, yet the dynamics of this process are not well understood. In this study, photocoagulation of albumen (egg white) was analysed experimentally and results compared with optical-thermal simulations to investigate a rate process approach to thermal damage and the role of heat conduction and dynamic changes in absorption. The coagulation threshold was determined using probit analysis, and coagulum dynamics were documented with fast flash photography. The nonlinear computational model, which included a Beer's law optical component, a finite difference heat transfer component and an Arrhenius equation-based damage calculation, was verified against data from the literature. Moderate discrepancies between simulation results and our experimental data probably resulted from the use of a laser beam with an irregular spatial profile. This profile produced a lower than expected coagulation threshold and an irregular damage distribution within a millisecond after laser onset. After 1 ms, heat conduction led to smoothing of the coagulum. Simulations indicated that dynamic changes in absorption led to a reduction in surface temperatures. The Arrhenius equation was shown to be effective for simulating transient albumen coagulation during pulsed holmium:YAG laser irradiation. Greater understanding of pulsed laser-tissue interactions may lead to improved treatment outcome and optimization of laser parameters for a variety of medical procedures. (author)

  17. Modeling of ablation threshold dependence on pulse duration for dielectrics with ultrashort pulsed laser

    Science.gov (United States)

    Sun, Mingying; Zhu, Jianqiang; Lin, Zunqi

    2017-01-01

    We present a numerical model of plasma formation in ultrafast laser ablation on the dielectrics surface. Ablation threshold dependence on pulse duration is predicted with the model and the numerical results for water agrees well with the experimental data for pulse duration from 140 fs to 10 ps. Influences of parameters and approximations of photo- and avalanche-ionization on the ablation threshold prediction are analyzed in detail for various pulse lengths. The calculated ablation threshold is strongly dependent on electron collision time for all the pulse durations. The complete photoionization model is preferred for pulses shorter than 1 ps rather than the multiphoton ionization approximations. The transition time of inverse bremsstrahlung absorption needs to be considered when pulses are shorter than 5 ps and it can also ensure the avalanche ionization (AI) coefficient consistent with that in multiple rate equations (MREs) for pulses shorter than 300 fs. The threshold electron density for AI is only crucial for longer pulses. It is reasonable to ignore the recombination loss for pulses shorter than 100 fs. In addition to thermal transport and hydrodynamics, neglecting the threshold density for AI and recombination could also contribute to the disagreements between the numerical and the experimental results for longer pulses.

  18. Multifunctional optical correlator for picosecond ultraviolet laser pulse measurement.

    Science.gov (United States)

    Rakhman, Abdurahim; Wang, Yang; Garcia, Frances; Long, Cary; Huang, Chunning; Takeda, Yasuhiro; Liu, Yun

    2014-11-01

    A compact multifunctional optical correlator system for pulse width measurement of ultrashort ultraviolet (UV) pulses has been designed and experimentally demonstrated. Both autocorrelation and cross-correlation functions are measured using a single nonlinear crystal, and the switching between two measurements requires no adjustment of phase matching and detector. The system can measure UV pulse widths from sub-picoseconds to 100 ps, and it involves no auxiliary pulse in the measurement. The measurement results on a burst-mode picosecond UV laser show a high-quality performance on speed, accuracy, resolution, and dynamic range. The proposed correlator can be applied to measure any ultrashort UV pulses produced through sum-frequency generation or second-harmonic generation.

  19. Temporal laser pulse manipulation using multiple optical ring-cavities

    Science.gov (United States)

    Nguyen, Quang-Viet (Inventor); Kojima, Jun (Inventor)

    2010-01-01

    An optical pulse stretcher and a mathematical algorithm for the detailed calculation of its design and performance is disclosed. The optical pulse stretcher has a plurality of optical cavities, having multiple optical reflectors such that an optical path length in each of the optical cavities is different. The optical pulse stretcher also has a plurality of beam splitters, each of which intercepts a portion of an input optical beam and diverts the portion into one of the plurality of optical cavities. The input optical beam is stretched and a power of an output beam is reduced after passing through the optical pulse stretcher and the placement of the plurality of optical cavities and beam splitters is optimized through a model that takes into account optical beam divergence and alignment in the pluralities of the optical cavities. The optical pulse stretcher system can also function as a high-repetition-rate (MHz) laser pulse generator, making it suitable for use as a stroboscopic light source for high speed ballistic projectile imaging studies, or it can be used for high speed flow diagnostics using a laser light sheet with digital particle imaging velocimetry. The optical pulse stretcher system can also be implemented using fiber optic components to realize a rugged and compact optical system that is alignment free and easy to use.

  20. Efficient chirped-pulse amplification of sub-20 fs laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, Shinichi; Yamakawa, Koichi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1998-03-01

    We have developed a model for ultrabroadband and ultrashort pulse amplification including the effects of a pulse shaper for regenerative pulse shaping, gain narrowing and gain saturation in the amplifiers. Thin solid etalons are used to control both gain narrowing and gain saturation during amplification. This model has been used to design an optimized Ti:sapphire amplifier system for producing efficiently pulses of < 20-fs duration with approaching peak and average powers of 100 TW and 20 W. (author)

  1. Field-free molecular orientation by delayed elliptically polarised laser pulses

    Science.gov (United States)

    Maan, Anjali; Tyagi, Ashish; Prasad, Vinod

    2018-01-01

    A theoretical model of NAREX (non-adiabatic rotational excitation) and field-free molecular orientation by a short specific elliptically polarised laser pulses (EPLPs) driving a polar molecule is presented. By choosing the proper value of elliptically polarised field parameters, efficient field-free orientation could be achieved. It is demonstrated that NAREX can be controlled by various laser parameters, out of which pulse shape plays the most significant role. The effect of elliptic parameter on the rotational excitation and orientation dynamics is also under concern.

  2. Polycrystalline ZnTe thin film on silicon synthesized by pulsed laser deposition and subsequent pulsed laser melting

    Science.gov (United States)

    Xu, Menglei; Gao, Kun; Wu, Jiada; Cai, Hua; Yuan, Ye; Prucnal, S.; Hübner, R.; Skorupa, W.; Helm, M.; Zhou, Shengqiang

    2016-03-01

    ZnTe thin films on Si substrates have been prepared by pulsed laser deposition and subsequent pulsed laser melting (PLM) treatment. The crystallization during PLM is confirmed by Raman scattering, x-ray diffraction and room temperature photoluminescence (PL) measurements. The PL results show a broad peak at 574 nm (2.16 eV), which can be assigned to the transitions from the conduction band to the acceptor level located at 0.145 eV above the valence band induced by zinc-vacancy ionization. Our work provides an applicable approach to low temperature preparation of crystalline ZnTe thin films.

  3. Size-controlled growth of ZnO nanowires by catalyst-free high-pressure pulsed laser deposition and their optical properties

    Directory of Open Access Journals (Sweden)

    W. Z. Liu

    2011-06-01

    Full Text Available Single crystalline ZnO nanowires were fabricated on Si (100 substrates by catalyst-free high-pressure pulsed laser deposition. It is found that the nanowires start to form when the substrate temperature and growth pressure exceed the critical values of 700 oC and 700 Pa, and their size strongly depends on these growth conditions. That is, the aspect ratio of the nanowires decreases with increasing temperature or decreasing pressure. Such a size dependence on growth conditions was discussed in terms of surface migration and scattering of ablated atoms. Room-temperature photoluminescence spectrum of ZnO nanowires shows a dominant near-band-edge emission peak at 3.28 eV and a visible emission band centered at 2.39 eV. Temperature-dependent photoluminescence studies reveal that the former consists of the acceptor-bound exciton and free exciton emissions; while the latter varies in intensity with the aspect ratio of the nanowires and is attributed to the surface-mediated deep level emission.

  4. Infantile hemangioma: pulsed dye laser versus surgical therapy

    Science.gov (United States)

    Remlova, E.; Dostalova, T.; Michalusova, I.; Vranova, J.; Jelinkova, H.; Hubacek, M.

    2014-05-01

    Hemangioma is a mesenchymal benign tumor formed by blood vessels. Anomalies affect up to 10% of children and they are more common in females than in males. The aim of our study was to compare the treatment efficacy, namely the curative effect and adverse events, such as loss of pigment and appearance of scarring, between classical surgery techniques and laser techniques. For that reason a group of 223 patients with hemangioma was retrospectively reviewed. For treatment, a pulsed dye laser (PDL) (Rhodamine G, wavelength 595 nm, pulsewidth between 0.45 and 40 ms, spot diameter 7 mm, energy density 9-11 J cm-2) was used and the results were compared with a control group treated with classical surgical therapy under general anesthesia. The curative effects, mainly number of sessions, appearance of scars, loss of pigment, and relapses were evaluated as a marker of successful treatment. From the results it was evident that the therapeutic effects of both systems are similar. The PDL was successful in all cases. The surgery patients had four relapses. Classical surgery is directly connected with the presence of scars, but the system is safe for larger hemangiomas. It was confirmed that the PDL had the optimal curative effect without scars for small lesions (approximately 10 mm). Surgical treatment under general anesthesia is better for large hemangiomas; the disadvantage is the presence of scars.

  5. Electron optical injection with head-on and countercrossing colliding laser pulses.

    Science.gov (United States)

    Kotaki, H; Daito, I; Kando, M; Hayashi, Y; Kawase, K; Kameshima, T; Fukuda, Y; Homma, T; Ma, J; Chen, L-M; Esirkepov, T Zh; Pirozhkov, A S; Koga, J K; Faenov, A; Pikuz, T; Kiriyama, H; Okada, H; Shimomura, T; Nakai, Y; Tanoue, M; Sasao, H; Wakai, D; Matsuura, H; Kondo, S; Kanazawa, S; Sugiyama, A; Daido, H; Bulanov, S V

    2009-11-06

    A high stability electron bunch is generated by laser wakefield acceleration with the help of a colliding laser pulse. The wakefield is generated by a laser pulse; the second laser pulse collides with the first pulse at 180 degrees and at 135 degrees realizing optical injection of an electron bunch. The electron bunch has high stability and high reproducibility compared with single pulse electron generation. In the case of 180 degrees collision, special measures have been taken to prevent damage. In the case of 135 degrees collision, since the second pulse is countercrossing, it cannot damage the laser system.

  6. MODIFICATION OF SILICON ABSORPTIVITY UNDER FEMTOSECOND LASER PULSE

    Directory of Open Access Journals (Sweden)

    I. V. Guk,

    2013-05-01

    Full Text Available The article deals with theoreticalmodeling results of the combined influence of nonlinear absorptivity and absorption coefficient on the spatial and temporal distribution of the electron-hole plasma and the dynamics of the specific absorption flux in silicon under femtosecond laser pulse. It is shown thatincreased absorption of the hot electron gas makes the main contribution to the change in specific absorption flux. Obtained results were compared with the known views about the polariton mechanism,which is usedfor the interpretation of femtosecond laser silicon microstructuring. There aredemonstratedThe need to consider absorption capacity dynamics in the regimes assessment of ultra short laser semiconductor processing.

  7. Ionization of O2 molecule by n-cycle circularly polarized laser pulses

    Science.gov (United States)

    Ren, Xianghe; Yang, Qingbo; Zhang, Jingtao

    2017-08-01

    In this paper we investigate the ionization of O2 molecule exposed to few-cycle pulses with different optical cycle numbers by calculating the photoelectron angular distributions (PADs) of O2 molecule. In order to show the influence of the molecular electronic structure and the laser pulse on the PADs, we also calculate the PADs of H atom, which has an isotropic electronic distribution in its ground state. We find that for one-cycle laser pulse, the PADs of O2 molecule are inversion asymmetric, and the PADs are not dependent on the photoelectron energy. For two-cycle and three-cycle laser pulses, although the PADs are still inversion asymmetric, the PADs have a certain dependence on the photoelectron energy. According to this phenomenon, we can control the emission directions of photoelectrons by choosing a fitted photoelectron energy. At same time, with a fitted photoelectron energy, by changing the carrier-envelope (CE) phase, the split position of the PADs of O2 molecule can be controlled, and then can forecast the main emission direction of photoelectron. While for long pulse (ten-cycle pulse) the dependence of PADs on the photoelectron energy nearly disappears, and the ionization behaviors extend to that in an infinitely monochromatic plane wave.

  8. Nitridation of Nb surface by nanosecond and femtosecond laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Farha, Ashraf Hassan [Department of Electrical and Computer Engineering and the Applied Research Center, Old Dominion University, Norfolk, VA 23529 (United States); Department of Physics, Faculty of Science, Ain Shams University, Cairo 11566 (Egypt); Ozkendir, Osman Murat [Tarsus Technology Faculty, Mersin University, Tarsus 33480 (Turkey); Koroglu, Ulas; Ufuktepe, Yüksel [Department of Physics, Cukurova University, Adana 01330 (Turkey); Elsayed-Ali, Hani E., E-mail: helsayed@odu.edu [Department of Electrical and Computer Engineering and the Applied Research Center, Old Dominion University, Norfolk, VA 23529 (United States)

    2015-01-05

    Highlights: • Laser nitridation of niobium is performed with nanosecond and femtosecond pulses. • Formation of NbN{sub x} with mixed α, β and δ phases was observed. • For femtosecond laser processed samples, laser induced ripple patterns oriented parallel to the beam polarization were formed. • X-ray absorption near edge structure show formation of Nb{sub 2}O{sub 5} on the surface of the samples. - Abstract: Niobium nitride samples were prepared by laser nitridation in a reactive nitrogen gas environment at room temperature using a Q-switched Nd:YAG nanosecond laser and a Ti:sapphire femtosecond laser. The effects of laser fluence on the formed phase, surface morphology, and electronic properties of the NbN{sub x} were investigated. The samples were prepared at different nanosecond laser fluences up to 5.0 ± 0.8 J/cm{sup 2} at fixed nitrogen pressure of ∼2.7 × 10{sup 4} Pa formed NbN{sub x} with mainly the cubic δ-NbN phase. Femtosecond laser nitrided samples were prepared using laser fluences up to 1.3 ± 0.3 mJ/cm{sup 2} at ∼4.0 × 10{sup 4} Pa nitrogen pressure. Laser induced ripple patterns oriented parallel to the beam polarization were formed with spacing that increases with the laser fluence. To achieve a laser-nitrided surface with desired crystal orientation the laser fulence is an important parameter that needs to be properly adjusted.

  9. Effect of aging on copper nanoparticles synthesized by pulsed laser ...

    Indian Academy of Sciences (India)

    Effect of aging on copper nanoparticles synthesized by pulsed laser ablation of copper plate in water was studied. By characterization studies of the aged nanoparticles, it is found that copper nanoparticles converted into Cu@Cu2O nanostructure. The synthesized nanomaterial is characterized with UV-Visible absorption, ...

  10. Modeling short-pulse laser excitation of dielectric materials

    DEFF Research Database (Denmark)

    Wædegaard, Kristian Juncher; Sandkamm, Ditte Både; Haahr-Lillevang, Lasse

    2014-01-01

    A theoretical description of ultrashort-pulse laser excitation of dielectric materials based on strong-field excitation in the Keldysh picture combined with a multiple-rateequation model for the electronic excitation including collisional processes is presented. The model includes light attenuation...

  11. Epitaxial oxide thin films by pulsed laser deposition: Retrospect and ...

    Indian Academy of Sciences (India)

    Unknown

    Among the large number of processes to fabricate thin films of materials, pulsed laser deposition (PLD) has emerged as a ... It is important to recognize that highly stoichiometric, nearly single crystal like epitaxial film is aimed for in the PLD .... This new class of Josephson junctions is attractive for novel phase devices.

  12. RHEED study of titanium dioxide with pulsed laser deposition

    DEFF Research Database (Denmark)

    Rasmussen, Inge Lise; Pryds, Nini; Schou, Jørgen

    2009-01-01

    Reflection high-energy electron diffraction (RHEED) operated at high pressure has been used to monitor the growth of thin films of titanium dioxide (TiO2) on (1 0 0) magnesium oxide (MgO) substrates by pulsed laser deposition (PLD). The deposition is performed with a synthetic rutile TiO2 target...

  13. Surface melting of copper by ultrashort laser pulses

    NARCIS (Netherlands)

    Oboňa, J.V.; Ocelík, V.; De Hosson, J.T.M.; Skolski, J.Z.P.; Mitko, V.S.; Römer, G.R.B.E.; Huis in 't Veld, A.J.

    2011-01-01

    The main advantage of ultrashort laser pulses in manufacturing technology is their very high removal rate of material and high quality of microstructures with the smallest dimensions at 1 μm level. The accuracy is mainly due to an almost absence of thermal diffusion into bulk material. In this paper

  14. Non-stoichiometry in sulfides produced by pulsed laser deposition

    DEFF Research Database (Denmark)

    Canulescu, Stela; Cazzaniga, Andrea Carlo; Ettlinger, Rebecca Bolt

    Pulsed laser deposition or PLD is known as a technique by which complex materials can be stoichiometrically transferred from a target to a substrate, providing that the ablation threshold is exceeded. For a multi-target component, it frequently happens that there is loss of the lightest and the m...

  15. Treatment of lupus erythematosus with pulsed dye laser.

    Science.gov (United States)

    Baniandrés, Ofelia; Boixeda, Pablo; Belmar, Paulina; Pérez, Alejandro

    2003-01-01

    The treatment of cutaneous lupus erythematosus (CLE) with dye and argon laser has been evaluated in a number of articles in recent years. The improvement of telangiectasias and chronic erythema of the cutaneous lesions was based on the selective photothermolysis ablation of the dilated capillaries and venules. We describe the results of the treatment of cutaneous lesions of 14 patients; eight with discoid lupus erythematosus (DLE) and six with systemic lupus erythematosus (SLE). Three patients received a treatment with flashlamp pulsed dye laser (FPDL) (585 nm, 450 microseconds) with fluences in the range from 5 to 7.75 J/cm(2); the other 11 patients were treated with long pulsed dye laser (LPDL) (595 nm, 1.5-10 milliseconds) with fluences in the range from 6 to 13 J/cm(2) depending on the pulse duration. During a median follow-up of 10 months, we observed an average improvement in over 60% of the lesions. A few side effects were observed in all patients: four had transient hyperpigmentation and one patient had light scarring. Three patients had a relapse after more than 1 year; they were then offered conventional treatment. We confirm that pulsed dye laser is a good alternative treatment for the erythema in active cutaneous lesions of lupus erythematosus (LE). Copyright 2003 Wiley-Liss, Inc.

  16. Tracking Femtosecond Laser Pulses in Space and Time

    NARCIS (Netherlands)

    Balistreri, M.L.M.; Gersen, H.; Korterik, Jeroen P.; Kuipers, L.; van Hulst, N.F.

    2001-01-01

    We show that the propagation of a femtosecond laser pulse inside a photonic structure can be directly visualized and tracked as it propagates using a time-resolved photon scanning tunneling microscope. From the time-dependent and phase- sensitive measurements, both the group velocity and the phase

  17. Influence of SOD on THG for femtosecond laser pulse

    Science.gov (United States)

    Trofimov, Vyacheslav A.; Sidorov, Pavel S.

    2017-02-01

    THG is used nowadays in many practical applications such as a substance diagnostics, and biological objects imaging, and etc. Therefore, THG features understanding are urgent problem and this problem attracts an attention of many researchers. In this paper we analyze THG efficiency of a femtosecond laser pulse. Consideration is based on computer simulation of the laser pulse propagation with taking into account a selfand cross- modulation of the interacting waves, and their SOD, and phase mismatching. Moreover, we analyze an influence of the non-homogeneous phase mismatching along laser pulse propagation coordinate. In this case, a phase matching occurs only in narrow area of longitudinal coordinate. Due to strong self- and crossmodulation of interacting waves it is possible to manage effective THG. Using the frame-work of long pulse duration approximation and plane wave approximation as well as an original approach we write the explicit solution of Schrödinger equations describing the frequency tripling of femtosecond pulse. It should be stressed, that the main feature of our approach consists in conservation laws using corresponding to wave interaction process.

  18. Electra: durable repetitively pulsed angularly multiplexed KrF laser system

    Science.gov (United States)

    Wolford, Matthew F.; Myers, Matthew C.; Giuliani, John L.; Sethian, John D.; Burns, Patrick M.; Hegeler, Frank; Jaynes, Reginald

    2008-02-01

    Electra is a repetitively pulsed, electron beam pumped Krypton Fluoride (KrF) laser at the Naval Research Laboratory that is developing the technologies that can meet the Inertial Fusion Energy (IFE) requirements for durability, efficiency, and cost. The technologies developed on Electra should be directly scalable to a full size fusion power plant beam line. As in a full size fusion power plant beam line, Electra is a multistage laser amplifier system which, consists of a commercial discharge laser (LPX 305i, Lambda Physik), 175 keV electron beam pumped (40 ns flat-top) preamplifier, and 530 keV (100 ns flat-top) main amplifier. Angular multiplexing is used in the optical layout to provide pulse length control and to maximize laser extraction from the amplifiers. Single shot yield of 452 J has been extracted from the initial shots of the Electra laser system using a relatively low energy preamplifier laser beam. In rep-rate burst of 5 Hz for durations of one second a total energy of 1.585 kJ (average 317 J/pulse) has been attained. Total energy of 2.5 kJ has been attained over a two second period. For comparison, the main amplifier of Electra in oscillator mode has demonstrated at 2.5 Hz rep-rate average laser yield of 270 J over a 2 hour period.

  19. Study on laser welding of austenitic stainless steel by varying incident angle of pulsed laser beam

    Science.gov (United States)

    Kumar, Nikhil; Mukherjee, Manidipto; Bandyopadhyay, Asish

    2017-09-01

    In the present work, AISI 304 stainless steel sheets are laser welded in butt joint configuration using a robotic control 600 W pulsed Nd:YAG laser system. The objective of the work is of twofold. Firstly, the study aims to find out the effect of incident angle on the weld pool geometry, microstructure and tensile property of the welded joints. Secondly, a set of experiments are conducted, according to response surface design, to investigate the effects of process parameters, namely, incident angle of laser beam, laser power and welding speed, on ultimate tensile strength by developing a second order polynomial equation. Study with three different incident angle of laser beam 89.7 deg, 85.5 deg and 83 deg has been presented in this work. It is observed that the weld pool geometry has been significantly altered with the deviation in incident angle. The weld pool shape at the top surface has been altered from semispherical or nearly spherical shape to tear drop shape with decrease in incident angle. Simultaneously, planer, fine columnar dendritic and coarse columnar dendritic structures have been observed at 89.7 deg, 85.5 deg and 83 deg incident angle respectively. Weld metals with 85.5 deg incident angle has higher fraction of carbide and δ-ferrite precipitation in the austenitic matrix compared to other weld conditions. Hence, weld metal of 85.5 deg incident angle achieved higher micro-hardness of ∼280 HV and tensile strength of 579.26 MPa followed by 89.7 deg and 83 deg incident angle welds. Furthermore, the predicted maximum value of ultimate tensile strength of 580.50 MPa has been achieved for 85.95 deg incident angle using the developed equation where other two optimum parameter settings have been obtained as laser power of 455.52 W and welding speed of 4.95 mm/s. This observation has been satisfactorily validated by three confirmatory tests.

  20. Formation of ultrasmooth thin silver films by pulsed laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, I. A.; Garaeva, M. Ya.; Mamichev, D. A., E-mail: d_mamichev@mail.ru; Grishchenko, Yu. V.; Zanaveskin, M. L. [NBIC Center, National Research Centre ' Kurchatov Institute' (Russian Federation)

    2013-09-15

    Ultrasmooth thin silver films have been formed on a quartz substrate with a buffer yttrium oxide layer by pulsed laser deposition. The dependence of the surface morphology of the film on the gas (N{sub 2}) pressure in the working chamber and laser pulse energy is investigated. It is found that the conditions of film growth are optimal at a gas pressure of 10{sup -2} Torr and lowest pulse energy. The silver films formed under these conditions on a quartz substrate with an initial surface roughness of 0.3 nm had a surface roughness of 0.36 nm. These films can be used as a basis for various optoelectronics and nanoplasmonics elements.

  1. Efficient self-sustained pulsed CO laser

    NARCIS (Netherlands)

    Peters, P.J.M.

    1978-01-01

    In this paper a simple sealed-off TEA CO laser is described with a self-sustained discharge without an external UV preionization source. At 77 K this system yields more than 600 mJ from a lasing volume of about 60 cm3 CO-N2-He mixture (45 J/ℓ atm. with 15.6% efficiency).

  2. Pulsed laser deposition of anatase thin films on textile substrates

    Energy Technology Data Exchange (ETDEWEB)

    Krämer, André; Kunz, Clemens; Gräf, Stephan; Müller, Frank A.

    2015-10-30

    Highlights: • Anatase thin films were grown on carbon fibre fabrics by pulsed laser deposition. • A novel Q-switched CO{sub 2} laser was utilised as radiation source. • Coated fibres exhibit photocatalytic activity and are resistant against bending. - Abstract: Pulsed laser deposition (PLD) is a highly versatile tool to prepare functional thin film coatings. In our study we utilised a Q-switched CO{sub 2} laser with a pulse duration τ ≈ 300 ns, a laser wavelength λ = 10.59 μm, a repetition frequency f{sub rep} = 800 Hz and a peak power P{sub peak} = 15 kW to deposit crystalline anatase thin films on carbon fibre fabrics. For this purpose, preparatory experiments were performed on silicon substrates to optimise the anatase deposition conditions including the influence of different substrate temperatures and oxygen partial pressures. Processing parameters were then transferred to deposit anatase on carbon fibres. Scanning electron microscopy, X-ray diffraction analyses, Raman spectroscopy and tactile profilometry were used to characterise the samples and to reveal the formation of phase pure anatase without the occurrence of a secondary rutile phase. Methanol conversion test were used to prove the photocatalytic activity of the coated carbon fibres.

  3. Making Relativistic Positrons Using Ultra-Intense Short Pulse Lasers

    Energy Technology Data Exchange (ETDEWEB)

    Chen, H; Wilks, S; Bonlie, J; Chen, C; Chen, S; Cone, K; Elberson, L; Gregori, G; Liang, E; Price, D; Van Maren, R; Meyerhofer, D D; Mithen, J; Murphy, C V; Myatt, J; Schneider, M; Shepherd, R; Stafford, D; Tommasini, R; Beiersdorfer, P

    2009-08-24

    This paper describes a new positron source produced using ultra-intense short pulse lasers. Although it has been studied in theory since as early as the 1970s, the use of lasers as a valuable new positron source was not demonstrated experimentally until recent years, when the petawatt-class short pulse lasers were developed. In 2008 and 2009, in a series of experiments performed at Lawrence Livermore National Laboratory, a large number of positrons were observed after shooting a millimeter thick solid gold target. Up to 2 x 10{sup 10} positrons per steradian ejected out the back of {approx}mm thick gold targets were detected. The targets were illuminated with short ({approx}1 ps) ultra-intense ({approx}1 x 10{sup 20} W/cm{sup 2}) laser pulses. These positrons are produced predominantly by the Bethe-Heitler process, and have an effective temperature of 2-4 MeV, with the distribution peaking at 4-7 MeV. The angular distribution of the positrons is anisotropic. For a wide range of applications, this new laser based positron source with its unique characteristics may complements the existing sources using radioactive isotopes and accelerators.

  4. Laser Cooling with Ultrafast Pulse Trains

    Science.gov (United States)

    2011-08-08

    unprecedented agreement between ab initio theory and experiment in this field by investigating ionisation of atomic hydrogen with few-cycle pulses [1]. Figure 1...Abeln, K Bartschat, I Ivanov, A Kheifets, HM Quiney, IV Litvinyuk, RT Sang, and D Kielpinski, “Above threshold ionisation of atomic hydrogen using few...Grzhimailo, B Abeln, K Bartschat, I Ivanov, A Kheifets, HM Quiney, IV Litvinyuk, RT Sang, and D Kielpinski, “Above threshold ionisation of atomic

  5. Power supplied for pulsed laser systems

    Science.gov (United States)

    Ed Strickland, B.; Nelms, R. Mark

    1995-01-01

    Conventional DC power supplies are normally designed for loads with constant or near constant power requirements and do not perform well under the wide range of load variations involved in repetitively charging an energy storage capacitor from zero volts to a maximum voltage. This paper will discuss a family of capacitor charging power supplies developed in a collaborative effort between Auburn University and Maxwell Laboratories in San Diego, California. These supplies utilize resonant technology and a patented pulse-width modulation scheme.

  6. Laser pulse detection method and apparatus

    Science.gov (United States)

    Goss, W.; Janesick, J. R.

    1984-02-01

    A sensor is described for detecting the difference in phase of a pair of returned light pulse components, such as two components of a light pulse of an optical gyro. In an optic gyro, the two light components have passed in opposite directions through a coil of optical fiber, with the difference in phase of the returned light components determining the intensity of light shining on the sensor. The sensor includes a CCD (charge coupled device) that receives the pair of returned light components to generate a charge proportional to the number of photons in the received light. The amount of the charge represents the phase difference between the two light components. At a time after the transmission of the light pulse and before the expected time of arrival of the interfering light components, charge accumulating in the CCD as a result of reflections from components in the system, are repeatedly removed from the CCD, by transferring out charges in the CCD and dumping these charges.

  7. Diode-pumped solid state laser. (Part V). ; Short pulse laser oscillation. Handotai laser reiki kotai laser. 5. ; Tan pulse hasshin

    Energy Technology Data Exchange (ETDEWEB)

    Kuwabara, M.; Bando, N. (Asahi Glass Co. Ltd., Tokyo (Japan))

    1991-12-25

    A semiconductor laser (LD) excited solid state laser using an LD as an excited light source is under discussion for its practical applications to measurements, processing, communications, office automation, and medical areas. This paper describes the discussions given on the short pulse transmission using AOQ switching elements in the LD excited solid state laser with a long wave length band (1.3{mu}m), which is expected of its application in the communications and measurements area. Based on a possibility of raising a measurements resolution by making the pluses in the LD excited solid state laser, and experiments were performed using Nd:YLF as a laser host. as a results, it was found that the smaller the effective mode volume V {sub eff},the smaller the pulse width, and that the ratio of number of initial inversion distribution (N{sub i}/N{sub t}), an important parameter to determine pulse widths, can be obtained from the ratio of the LD exciting light to the input power (P{sub in}/P{sub t}). 7 refs., 14 figs., 2 tabs.

  8. Evidence of femtosecond-laser pulse induced cell membrane nanosurgery

    Science.gov (United States)

    Katchinskiy, Nir; Godbout, Roseline; Elezzabi, Abdulhakem Y.

    2017-02-01

    The mechanism of femtosecond laser nanosurgical attachment is investigated in the following article. Using sub-10 femtosecond laser pulses with 800 nm central wavelength were used to attach retinoblastoma cells. During the attachment process the cell membrane phospholipid bilayers hemifuse into one shared phospholipid bilayer, at the location of attachment. Transmission electron microscopy was used in order to verify the above hypothesis. Based on the imaging results, it was concluded that the two cell membrane coalesce to form one single shared membrane. The technique of cell-cell attachment via femtosecond laser pulses could potentially serve as a platform for precise cell membrane manipulation. Manipulation of the cellular membrane is valuable for studying diseases such as cancer; where the expression level of plasma proteins on the cell membrane is altered.

  9. Medical and biological applications for ultrafast laser pulses

    Science.gov (United States)

    Lubatschowski, Holger; Heisterkamp, Alexander; Will, Fabian; Singh, Ajoy I.; Serbin, Jesper; Ostendorf, Andreas; Kermani, Omid; Heermann, R.; Welling, Herbert; Ertmer, Wolfgang

    2003-02-01

    Due to the low energy threshold of photodisruption with fs laser pulses, thermal and mechanical side effects are limited to the sub μm range. The neglection of side effects enables the use of ultrashort laser pulses in a broad field of medical applications. Moreover, the interaction process based on nonlinear absorption offers the opportunity to process transparent tissue three dimensionally inside the bulk. We demonstrate the feasibility of surgical procedures in different fields of medical interest: In ophthalmology intrastromal cutting and preparing of corneal flaps for refractive surgery in living animals is presented. Besides, the very low mechanical side effects enables the use of fs-laser in otoralyngology to treat ocecular bones. Moreover, the precise cutting quality can be used in fields of cardiovascular surgery for the treatment of arteriosclerosis as well as in dentistry to remove caries from dental hard tissue.

  10. Interaction of Repetitively Pulsed High Energy Laser Radiation With Matter

    Science.gov (United States)

    Hugenschmidt, Manfred

    1986-10-01

    The paper is concerned with laser target interaction processes involving new methods of improving the overall energy balance. As expected theoretically, this can be achieved with high repetition rate pulsed lasers even for initially highly reflecting materials, such as metals. Experiments were performed by using a pulsed CO2 laser at mean powers up to 2 kW and repetition rates up to 100 Hz. The rates of temperature rise of aluminium for example were thereby increased by lore than a factor of 3 as compared to cw-radiation of comparable power density. Similar improvements were found for the overall absorptivities that were increased by this method by more than an order of magnitude.

  11. Shadowgraphic imaging of material removal during laser drilling with a long pulse eximer laser

    NARCIS (Netherlands)

    Schoonderbeek, A.; Biesheuvel, C.A.; Hofstra, R.M.; Boller, Klaus J.; Meijer, J.

    2005-01-01

    After the development of a novel XeCl excimer laser with a nearly diffraction-limited beam and 175 ns pulse length, research was done on different industrial applications of this laser. Hole drilling, one of these applications, was studied extensively. A better understanding of the drilling process

  12. A New Kind of Laser Microphone Using High Sensitivity Pulsed Laser Vibrometer

    Science.gov (United States)

    Wang, Chen-Chia; Trivedi, Sudhir; Jin, Feng; Swaminathan, V.; Prasad, Narasimha S.

    2008-01-01

    We demonstrate experimentally a new kind of laser microphone using a highly sensitive pulsed laser vibrometer. By using the photo-electromotive-force (photo-EMF) sensors, we present data indicating the real-time detection of surface displacements as small as 4 pm.

  13. Laser surface and subsurface modification of sapphire using femtosecond pulses

    Energy Technology Data Exchange (ETDEWEB)

    Eberle, G., E-mail: eberle@iwf.mavt.ethz.ch [Institute of Machine Tools and Manufacturing, ETH Zurich, Leonhardstrasse 21, 8092 Zurich (Switzerland); Schmidt, M. [Chair of Photonic Technologies, University of Erlangen-Nuremberg, Konrad-Zuse-Strasse 3-5, 91052 Erlangen (Germany); Pude, F. [Inspire AG, Technoparkstrasse 1, 8005 Zurich (Switzerland); Wegener, K. [Institute of Machine Tools and Manufacturing, ETH Zurich, Leonhardstrasse 21, 8092 Zurich (Switzerland); Inspire AG, Technoparkstrasse 1, 8005 Zurich (Switzerland)

    2016-08-15

    Highlights: • Single and multipulse ablation threshold of aluminium oxide is determined. • Laser ablation, and in-volume modification followed by wet etching are demonstrated. • Quality following laser processing and laser-material interactions are studied. - Abstract: Two methods to process sapphire using femtosecond laser pulses are demonstrated, namely ablation (surface), and in-volume laser modification followed by wet etching (subsurface). Firstly, the single and multipulse ablation threshold is determined and compared with previous literature results. A unique application of ablation is demonstrated by modifying the entrance aperture of water jet orifices. Laser ablation exhibits advantages in terms of geometric flexibility and resolution, however, defects in the form of edge outbreaks and poor surface quality are evident. Secondly, the role of material transformation, polarisation state and formation of multi-focus structures after in-volume laser modification is investigated in order to explain their influence during the wet etching process. Laser scanning and electron microscopy as well as electron backscatter diffraction measurements supported by ion beam polishing are used to better understand quality and laser-material interactions of the two demonstrated methods of processing.

  14. Extending ultra-short pulse laser texturing over large area

    Energy Technology Data Exchange (ETDEWEB)

    Mincuzzi, G., E-mail: girolamo.mincuzzi@alphanov.com; Gemini, L.; Faucon, M.; Kling, R.

    2016-11-15

    Highlights: • We carried out metal surface texturing (Ripples, micro grooves, Spikes) using a high power, high repetition rate, industrial, Ultra-short pulses laser. • Extremely Fast processing is shown (Laser Scan speed as high as 90 m/s) with a polygon scanner head. • Stainless steel surface blackening with Ultra-short pulses laser has been obtained with unprecedented scanspeed. • Full SEM surface characterization was carried out for all the different structures obtained. • Reflectance measurements were carried out to characterize surface reflectance. - Abstract: Surface texturing by Ultra-Short Pulses Laser (UPL) for industrial applications passes through the use of both fast beam scanning systems and high repetition rate, high average power P, UPL. Nevertheless unwanted thermal effects are expected when P exceeds some tens of W. An interesting strategy for a reliable heat management would consists in texturing with a low fluence values (slightly higher than the ablation threshold) and utilising a Polygon Scanner Heads delivering laser pulses with unrepeated speed. Here we show for the first time that with relatively low fluence it is possible over stainless steel, to obtain surface texturing by utilising a 2 MHz femtosecond laser jointly with a polygonal scanner head in a relatively low fluence regime (0.11 J cm{sup −2}). Different surface textures (Ripples, micro grooves and spikes) can be obtained varying the scan speed from 90 m s{sup −1} to 25 m s{sup −1}. In particular, spikes formation process has been shown and optimised at 25 m s{sup −1} and a full morphology characterization by SEM has been carried out. Reflectance measurements with integrating sphere are presented to compare reference surface with high scan rate textures. In the best case we show a black surface with reflectance value < 5%.

  15. Temporal pulse shaping: a key parameter for the laser welding of dental alloys.

    Science.gov (United States)

    Bertrand, Caroline; Poulon-Quintin, Angeline

    2015-07-01

    This study aims to describe the effect of pulse shaping on the prevention of internal defects during laser welding for two dental alloys mainly used in prosthetic dentistry. Single spot, weld beads, and welds with 80 % overlapping were performed on Co-Cr-Mo and Pd-Ag-Sn cast plates with a pulsed neodymium-doped yttrium aluminum garnet (Nd:YAG) laser. A specific welding procedure using adapted parameters to each alloy was completed. All the possibilities for pulse shaping were tested: (1) the square pulse shape as a default setting, (2) a rising edge slope for gradual heating, (3) a falling edge slope to slow the cooling process, and (4) a combination of rising and falling edges. The optimization of the pulse shape is supposed to produce defect-free welds (crack, pores, voids). Cross-section SEM observations and Vickers microhardness measurements were made. Pd-Ag-Sn was highly sensitive to hot cracking, and Co-Cr-Mo was more sensitive to voids and small porosities (sometimes combined with cracks). Using a slow cooling ramp allowed a better control on the solidification process for those two alloys always preventing internal defects. A rapid slope should be preferred for Co-Cr-Mo alloys due to its low-laser beam reflectivity. On the opposite, for Pd-Ag-Sn alloy, a slow rising slope should be preferred because this alloy has a high-laser beam reflectivity.

  16. 80 GHz AlGaInAs/InP colliding-pulse mode-locked laser with high pulse power

    Science.gov (United States)

    Zhao, Pengchao; Liu, Anjin; Zheng, Wanhua

    2016-12-01

    We theoretically analyze the impact of a saturable absorber (SA) length on the pulse power of a semiconductor mode-locked laser and find that in the range of the SA length from 1.5 to 7%, a laser with a longer SA can generate pulses with a higher power. Based on the simulation, we demonstrate a colliding-pulse mode-locked laser with an 80 µm SA. The device generates pulses at 80 GHz, with a pulse width of 1.75 ps, peak power of 188 mW, pulse energy of 0.33 pJ, and time-bandwidth product of 0.51. The results provide new possibilities for the design of high-repetition frequency high-pulse power mode-locked lasers.

  17. The preparation of iron complex oxide nanoparticles by pulsed-laser ablation

    Science.gov (United States)

    Sasaki, T.; Terauchi, S.; Koshizaki, N.; Umehara, H.

    1998-05-01

    Nanoparticles of a calcium-iron complex oxide were prepared by pulsed laser ablation on silicon wafer substrates placed at off-axial positions against a target. An ArF excimer laser was used to irradiate a CaFe 2O 4 target in atmospheres of Ar and O 2 at room temperature. The effects of ambient pressure and laser pulse energy on size and composition of nanoparticles were investigated using atomic force microscopy and X-ray photoelectron spectroscopy. The nanoparticles obtained were almost spherical and 2 to 26 nm in diameter. The size distributions of the nanoparticles were very narrow and agreed with the log-normal distribution function. The nanoparticle size increased with ambient pressure and pulse energy. The Ca/Fe atomic ratios in the nanoparticles, however, decreased with increasing ambient pressure and were independent of pulse energy. By this technique, the size and composition of nanoparticles can be easily controlled by laser fluence and pressure during the laser ablation.

  18. Pulsed laser CVD investigations of single-wall carbon nanotube growth dynamics

    Science.gov (United States)

    Liu, Z.; Styers-Barnett, D. J.; Puretzky, A. A.; Rouleau, C. M.; Yuan, D.; Ivanov, I. N.; Xiao, K.; Liu, J.; Geohegan, D. B.

    2008-12-01

    The nucleation and rapid growth of single-wall carbon nanotubes (SWNTs) were explored by pulsed-laser assisted chemical vapor deposition (PLA-CVD). A special high-power, Nd:YAG laser system with tunable pulse width (>0.5 ms) was implemented to rapidly heat (>3×104°C/s) metal catalyst-covered substrates to different growth temperatures for very brief (sub-second) and controlled time periods as measured by in situ optical pyrometry. Utilizing growth directly on transmission electron microscopy grids, exclusively SWNTs were found to grow under rapid heating conditions, with a minimum nucleation time of >0.1 s. By measuring the length of nanotubes grown by single laser pulses, extremely fast growth rates (up to 100 microns/s) were found to result from the rapid heating and cooling induced by the laser treatment. Subsequent laser pulses were found not to incrementally continue the growth of these nanotubes, but instead activate previously inactive catalyst nanoparticles to grow new nanotubes. Localized growth of nanotubes with variable density was demonstrated through this process and was applied for the reliable direct-write synthesis of SWNTs onto pre-patterned, catalyst-covered metal electrodes for the synthesis of SWNT field-effect transistors.

  19. Pulsed Laser CVD Investigations of Single-Wall Carbon Nanotube Growth Dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Geohegan, David B [ORNL; Liu, Zuqin [ORNL; Styers-Barnett, David J [ORNL; Puretzky, Alexander A [ORNL; Rouleau, Christopher M [ORNL; Yuan, Dongning [Duke University; Ivanov, Ilia N [ORNL; Xiao, Kai [ORNL; Liu, Jie [Duke University

    2008-01-01

    The nucleation and rapid growth of single-wall carbon nanotubes (SWNTs) were explored by pulsed-laser assisted chemical vapor deposition (PLA-CVD). A special high-power, Nd:YAG laser system with tunable pulse width (> 0.5 ms) was implemented to rapidly heat (>30,000 C/s) metal catalyst-covered substrates to different growth temperatures for very brief (sub-second) and controlled time periods as measured by in situ optical pyrometry. Utilizing growth directly on transmission electron microscopy grids, exclusively SWNTs were found to grow under rapid heating conditions, with a minimum nucleation time of >0.10 s. By measuring the length of nanotubes grown by single laser pulses, extremely fast growth rates (up to 100 microns/s) were found to result from the rapid heating and cooling induced by the laser treatment. Subsequent laser pulses were found not to incrementally continue the growth of these nanotubes, but instead activate previously inactive catalyst nanoparticles to grow new nanotubes. Localized growth of nanotubes with variable density was demonstrated through this process, and was applied for the reliable direct-write synthesis of SWNTs onto pre-patterned, catalyst-covered metal electrodes for the synthesis of SWNT field-effect transistors.

  20. Nanofabrication of tailored surface structures in dielectrics using temporally shaped femtosecond-laser pulses.

    Science.gov (United States)

    Hernandez-Rueda, Javier; Götte, Nadine; Siegel, Jan; Soccio, Michelina; Zielinski, Bastian; Sarpe, Cristian; Wollenhaupt, Matthias; Ezquerra, Tiberio A; Baumert, Thomas; Solis, Javier

    2015-04-01

    We have investigated the use of tightly focused, temporally shaped femtosecond (fs)-laser pulses for producing nanostructures in two dielectric materials (sapphire and phosphate glass) with different characteristics in their response to pulsed laser radiation. For this purpose, laser pulses shaped by third-order dispersion (TOD) were used to generate temporally asymmetric excitation pulses, leading to the single-step production of subwavelength ablative and subablative surface structures. When compared to previous works on the interaction of tightly focused TOD-shaped pulses with fused silica, we show here that this approach leads to very different nanostructure morphologies, namely, clean nanopits without debris surrounding the crater in sapphire and well-outlined nanobumps and nanovolcanoes in phosphate glass. Although in sapphire the debris-free processing is associated with the much lower viscosity of the melt compared to fused silica, nanobump formation in phosphate glass is caused by material network expansion (swelling) upon resolidification below the ablation threshold. The formation of nanovolcanoes is a consequence of the combined effect of material network expansion and ablation occurring in the periphery and central part of the irradiated region, respectively. It is shown that the induced morphologies can be efficiently controlled by modulating the TOD coefficient of the temporally shaped pulses.

  1. Spectral shaping of attosecond pulses using two-colour laser fields

    Energy Technology Data Exchange (ETDEWEB)

    Mansten, E; Dahlstroem, J M; Johnsson, P; Swoboda, M; L' Huillier, A; Mauritsson, J [Department of Physics, Lund University, P O Box 118, SE-221 00 Lund (Sweden)], E-mail: erik.mansten@fysik.lth.se, E-mail: johan.mauritsson@fysik.lth.se

    2008-08-15

    We use a strong two-colour laser field composed of the fundamental (800 nm) and the second harmonic (400 nm) of an infrared (IR) laser field to generate attosecond pulses with controlled spectral and temporal properties. With a second-harmonic intensity equal to 15% of the IR intensity the second-harmonic field is strong enough to significantly alter and control the electron trajectories in the generation process. This enables us to tune the central photon energy of the attosecond pulses by changing the phase difference between the IR and the second-harmonic fields. In the time domain the radiation is emitted as a sequence of pulses separated by a full IR cycle. We also perform calculations showing that the effect of even stronger second-harmonic fields leads to an extended tunable range under conditions that are experimentally feasible.

  2. Pulsed photothermal depth profiling of tattoos undergoing laser removal treatment

    Science.gov (United States)

    Milanic, Matija; Majaron, Boris

    2012-02-01

    Pulsed photothermal radiometry (PPTR) allows noninvasive determination of temperature depth profiles induced by pulsed laser irradiation of strongly scattering biological tissues and organs, including human skin. In present study, we evaluate the potential of this technique for investigational characterization and possibly quantitative evaluation of laser tattoo removal. The study involved 5 healthy volunteers (3 males, 2 females), age 20-30 years, undergoing tattoo removal treatment using a Q-switched Nd:YAG laser. There were four measurement and treatment sessions in total, separated by 2-3 months. Prior to each treatment, PPTR measurements were performed on several tattoo sites and one nearby healthy site in each patient, using a 5 ms Nd:YAG laser at low radiant exposure values and a dedicated radiometric setup. The laser-induced temperature profiles were then reconstructed by applying a custom numerical code. In addition, each tatoo site was documented with a digital camera and measured with a custom colorimetric system (in tristimulus color space), providing an objective evaluation of the therapeutic efficacy to be correlated with our PPTR results. The results show that the laser-induced temperature profile in untreated tattoos is invariably located at a subsurface depth of 300 μm. In tattoo sites that responded well to laser therapy, a significant drop of the temperature peak was observed in the profiles obtained from PPTR record. In several sites that appeared less responsive, as evidenced by colorimetric data, a progressive shift of the temperature profile deeper into the dermis was observed over the course of consecutive laser treatments, indicating that the laser tattoo removal was efficient.

  3. Real-time energy measurement of high repetition rate ultrashort laser pulses using pulse integration and FPGA processing

    Science.gov (United States)

    Tang, Qi-jie; Yang, Dong-xu; Wang, Jian; Feng, Yi; Zhang, Hong-fei; Chen, Teng-yun

    2016-11-01

    Real-time energy measurement using pulse integration method for high repetition rate ultrashort laser pulses based on FPGA (Field-Programmable Gate Array) and high-speed pipeline ADC (Analog-to-Digital Convertor) is introduced in this paper. There are two parts contained in this method: pulse integration and real-time data processing. The pulse integration circuit will convert the pulse to the step type signals which are linear to the laser pulse energy. Through the real-time data processing part, the amplitude of the step signals will be obtained by ADC sampling and conducting calculation in real time in FPGA. The test result shows that the method with good linearity (4.770%) and without pulse measurement missing is suitable for ultrashort laser pulses with high repetition rate up to 100 MHz.

  4. Ultracold and ultrafast: Probing quantum gases with femtosecond laser pulses

    Science.gov (United States)

    Wessels, Philipp; Ruff, Bernhard; Kroker, Tobias; Pehmöller, Steffen; Simonet, Juliette; Drescher, Markus; Sengstock, Klaus

    2017-04-01

    Ultrafast lasers open new pathways for probing and manipulating ultracold atomic systems in order to address fundamental questions in quantum physics. The short pulses act as a highly localized instantaneous trigger to drive complex dynamics and enable access to coherence properties in macroscopic quantum targets and superfluid matter. We report on first experiments exploring ultracold 87Rb atoms and Bose-Einstein condensates (BEC) exposed to ultrashort laser pulses of 280 fs duration. The intense light pulses create ions within the focal region via strong-field ionization and the remaining atoms are detected by absorption imaging. Additionally, we quantify the momentum transferred to the atoms by the femtosecond laser pulse. Since the amount of generated ions is tunable, a tool with the potential to create hybrid quantum systems of few ions immersed in the trapped cloud is provided. First results already indicate the formation of a long-lived ultracold plasma state. Analyzing the charged fragments after ionization promises further insight so that we discuss perspectives on detecting ions and electrons in a new experimental setup to investigate coherence transfer from a macroscopic wave function to its microscopic constituents.

  5. Obtaining Cross-Sections of Paint Layers in Cultural Artifacts Using Femtosecond Pulsed Lasers

    Directory of Open Access Journals (Sweden)

    Takaaki Harada

    2017-01-01

    Full Text Available Recently, ultrafast lasers exhibiting high peak powers and extremely short pulse durations have created a new paradigm in materials processing. The precision and minimal thermal damage provided by ultrafast lasers in the machining of metals and dielectrics also suggests a novel application in obtaining precise cross-sections of fragile, combustible paint layers in artwork and cultural heritage property. Cross-sections of paint and other decorative layers on artwork provide critical information into its history and authenticity. However, the current methodology which uses a scalpel to obtain a cross-section can cause further damage, including crumbling, delamination, and paint compression. Here, we demonstrate the ability to make controlled cross-sections of paint layers with a femtosecond pulsed laser, with minimal damage to the surrounding artwork. The femtosecond laser cutting overcomes challenges such as fragile paint disintegrating under scalpel pressure, or oxidation by the continuous-wave (CW laser. Variations in laser power and translational speed of the laser while cutting exhibit different benefits for cross-section sampling. The use of femtosecond lasers in studying artwork also presents new possibilities in analyzing, sampling, and cleaning of artwork with minimal destructive effects.

  6. Obtaining Cross-Sections of Paint Layers in Cultural Artifacts Using Femtosecond Pulsed Lasers.

    Science.gov (United States)

    Harada, Takaaki; Spence, Stephanie; Margiolakis, Athanasios; Deckoff-Jones, Skylar; Ploeger, Rebecca; Shugar, Aaron N; Hamm, James F; Dani, Keshav M; Dani, Anya R

    2017-01-26

    Recently, ultrafast lasers exhibiting high peak powers and extremely short pulse durations have created a new paradigm in materials processing. The precision and minimal thermal damage provided by ultrafast lasers in the machining of metals and dielectrics also suggests a novel application in obtaining precise cross-sections of fragile, combustible paint layers in artwork and cultural heritage property. Cross-sections of paint and other decorative layers on artwork provide critical information into its history and authenticity. However, the current methodology which uses a scalpel to obtain a cross-section can cause further damage, including crumbling, delamination, and paint compression. Here, we demonstrate the ability to make controlled cross-sections of paint layers with a femtosecond pulsed laser, with minimal damage to the surrounding artwork. The femtosecond laser cutting overcomes challenges such as fragile paint disintegrating under scalpel pressure, or oxidation by the continuous-wave (CW) laser. Variations in laser power and translational speed of the laser while cutting exhibit different benefits for cross-section sampling. The use of femtosecond lasers in studying artwork also presents new possibilities in analyzing, sampling, and cleaning of artwork with minimal destructive effects.

  7. Obtaining Cross-Sections of Paint Layers in Cultural Artifacts Using Femtosecond Pulsed Lasers

    Science.gov (United States)

    Harada, Takaaki; Spence, Stephanie; Margiolakis, Athanasios; Deckoff-Jones, Skylar; Ploeger, Rebecca; Shugar, Aaron N.; Hamm, James F.; Dani, Keshav M.; Dani, Anya R.

    2017-01-01

    Recently, ultrafast lasers exhibiting high peak powers and extremely short pulse durations have created a new paradigm in materials processing. The precision and minimal thermal damage provided by ultrafast lasers in the machining of metals and dielectrics also suggests a novel application in obtaining precise cross-sections of fragile, combustible paint layers in artwork and cultural heritage property. Cross-sections of paint and other decorative layers on artwork provide critical information into its history and authenticity. However, the current methodology which uses a scalpel to obtain a cross-section can cause further damage, including crumbling, delamination, and paint compression. Here, we demonstrate the ability to make controlled cross-sections of paint layers with a femtosecond pulsed laser, with minimal damage to the surrounding artwork. The femtosecond laser cutting overcomes challenges such as fragile paint disintegrating under scalpel pressure, or oxidation by the continuous-wave (CW) laser. Variations in laser power and translational speed of the laser while cutting exhibit different benefits for cross-section sampling. The use of femtosecond lasers in studying artwork also presents new possibilities in analyzing, sampling, and cleaning of artwork with minimal destructive effects. PMID:28772468

  8. Charging and plasma effects under ultrashort pulsed laser ablation

    Science.gov (United States)

    Bulgakova, N. M.; Bulgakov, A. V.; Zhukov, V. P.; Marine, W.; Vorobyev, A. Y.; Guo, Chunlei

    2008-05-01

    Based on experiments and a theoretical analysis, we raise questions on two fundamental mechanisms of femtosecond laser desorption/ablation of solids, namely Coulomb explosion (CE) and plasma etching. The effects of laser-induced ionization and surface charging are analyzed which can be responsible for ultrafast ions observed in time-of-flight mass-spectra under ultrashort laser irradiation of solids. The importance of surface charging in formation of velocity distributions of desorbed/ablated species has been revealed for conditions when the CE mechanism is inhibited. The influence of ambient plasma formation on the dynamics of heating of metallic targets by femtosecond laser pulses is studied based on 2D modeling of laser-induced target heating and dynamics of the ambient plasma. The calculations show an intriguing picture of the laser-induced ambient gas motion. We propose a model of laser-induced breakdown of an ambient gas in a region in front of the irradiated target and analyze plasma-chemical processes which can affect laser processing of surfaces in the presence of air or highly reactive media.

  9. Calculations of population transfer during intense laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Schafer, K.J.; Kulander, K.C.

    1993-08-01

    Recent experiments by several groups have examined the question of population transfer to resonantly excited states during intense short laser pulses, in particular the amount of population that remains ``trapped`` in excited states at the end of a laser pulse. In this chapter we present calculations of population transfer and resonant ionization in xenon at both 660 and 620 nm. At the longer wavelength, the seven photon channel closes at 2.5{times}10{sup 13} W/cm{sup 2}. Pulses with peak intensities higher than this result in ``Rydberg trapping``, the resonant transfer of population to a broad range of high-lying states. The amount of population transferred depends on both the peak intensity and pulse duration. At 620 mm there are numerous possible six photon resonances to states with p or f angular momentum. We have done a large number of calculations for 40 fs pulses at different peak intensities and have examined the population transferred to these low-lying resonant states as a function of the peak laser intensity. We do not have room to comment upon the resonantly enhanced ionized electron energy spectra that we also determine in the same calculations. Our calculations involve the direct numerical integration of the time-dependent Schroedinger equation for an atom interacting with a strong laser field. The time-dependent wave function of a given valence electron is calculated on a spatial grid using a one-electron pseudo potential. This single active electron approximation (SAE) has been shown to be a good approximation for the rare gases at the intensities and wavelengths that we will consider. The SAE potential we use has an explicit angular momentum dependence which allows us to reproduce all of the excited state energies for xenon quite well.

  10. Short electron bunches generated by perpendicularly crossing laser pulses

    Science.gov (United States)

    Horný, Vojtěch; Petržílka, Václav; Klimo, Ondřej; Krůs, Miroslav

    2017-10-01

    Optical injection of electrons into a laser wakefield accelerator by a low intensity orthogonally colliding laser pulse is investigated using 2D particle-in-cell simulations. The collision of the main laser pulse driving the plasma wave in the cavitated regime and the low intensity injection pulse affects the trajectories of electrons in the crossing region. As a consequence, some electrons are ejected into the front part of the bubble, and these electrons are subsequently trapped in the rear part of the bubble. The injected and accelerated electron bunch reaches a peak energy of 630 MeV after 8 ps of acceleration being as short as 7.0 fs and is quasimonoenergetic with a low energy spread of 20 MeV (3.8%), having a charge of several dozens of pC and a relatively large emittance of 2.27 π . mm . mrad. Two main injection mechanisms—crossing beatwave injection and injection by laser field preacceleration—were identified.

  11. Longitudinally excited CO2 laser with short laser pulse operating at high repetition rate

    Science.gov (United States)

    Li, Jianhui; Uno, Kazuyuki; Akitsu, Tetsuya; Jitsuno, Takahisa

    2016-11-01

    A short-pulse longitudinally excited CO2 laser operating at a high repetition rate was developed. The discharge tube was made of a 45 cm-long or 60 cm-long dielectric tube with an inner diameter of 16 mm and two metallic electrodes at the ends of the tube. The optical cavity was formed by a ZnSe output coupler with a reflectivity of 85% and a high-reflection mirror. Mixed gas (CO2:N2:He = 1:1:2) was flowed into the discharge tube. A high voltage of about 33 kV with a rise time of about 200 ns was applied to the discharge tube. At a repetition rate of 300 Hz and a gas pressure of 3.4 kPa, the 45 cm-long discharge tube produced a short laser pulse with a laser pulse energy of 17.5 mJ, a spike pulse energy of 0.2 mJ, a spike width of 153 ns, and a pulse tail length of 90 μs. The output power was 5.3 W. The laser pulse waveform did not depend on the repetition rate, but the laser beam profile did. At a low repetition rate of less than 50 Hz, the laser beam had a doughnut-like shape. However, at a high repetition rate of more than 150 Hz, the discharge concentrated at the center of the discharge tube, and the intensity at the center of the laser beam was higher. The laser beam profile depended on the distribution of the discharge. An output power of 7.0 W was achieved by using the 60 cm-long tube.

  12. Determination of the temporal structure of femtosecond laser pulses by means of laser-induced air plasma

    Science.gov (United States)

    Zhang, Nan; Bao, Wen-Xia; Yang, Jing-Hui; Zhu, Xiao-Nong

    2013-05-01

    A new approach is presented to reveal the temporal structure of femtosecond laser pulses by recording the corresponding time-resolved shadowgraphs of the laser-induced air plasma. It is shown that the temporal structures of femtosecond laser pulses, normally not observable by the ordinary intensity autocorrelator, can be detected through intuitively analyzing the ultrafast evolution process of the air plasma induced by the femtosecond laser pulses under examination. With this method, existence of pre- and post-pulses has been clearly unveiled within the time window of ±150 fs in reference with the main 50-fs laser pulses output from a commercial 1-kHz femtosecond laser amplifier. The unique advantage of the proposed method is that it can directly provide valuable information about the pulse temporal structures' effect on the laser-induced ionization or material ablation.

  13. Localized dispersing of ceramic particles in tool steel surfaces by pulsed laser radiation

    Energy Technology Data Exchange (ETDEWEB)

    Hilgenberg, K., E-mail: hilgenberg@uni-kassel.de [Metal Forming Technology, University of Kassel (Germany); Behler, K. [Laser Technology, THM University of Applied Sciences (Germany); Steinhoff, K. [Metal Forming Technology, University of Kassel (Germany)

    2014-06-01

    In this paper the capability of a localized laser dispersing technique for changing the material microstructure and the surface topology of steels is discussed. The laser implantation named technique bases on a discontinuous dispersing of ceramic particles into the surface of steels by using pulsed laser radiation. As ceramic particles TiC, WC and TiB{sub 2} are used, substrate material is high-alloyed cold working steel (X153CrMoV12). The influence of the laser parameters pulse length and pulse intensity was investigated in a comprehensive parameter study. The gained surface topology and microstructure were evaluated by optical microscopy, energy dispersive X-ray spectroscopy (EDX) and white light interferometry; mechanical properties were analyzed by micro hardness measurement. The experiments reveal that the alignment of separated, elevated, dome-shaped spots on the steel surface is feasible. The geometrical properties as well as the mechanical properties are highly controllable by the laser parameters. The laser implanted spots show a mostly crack-free and pore-free bonding to the substrate material as well as a significant increase of micro hardness.

  14. Localized dispersing of ceramic particles in tool steel surfaces by pulsed laser radiation

    Science.gov (United States)

    Hilgenberg, K.; Behler, K.; Steinhoff, K.

    2014-06-01

    In this paper the capability of a localized laser dispersing technique for changing the material microstructure and the surface topology of steels is discussed. The laser implantation named technique bases on a discontinuous dispersing of ceramic particles into the surface of steels by using pulsed laser radiation. As ceramic particles TiC, WC and TiB2 are used, substrate material is high-alloyed cold working steel (X153CrMoV12). The influence of the laser parameters pulse length and pulse intensity was investigated in a comprehensive parameter study. The gained surface topology and microstructure were evaluated by optical microscopy, energy dispersive X-ray spectroscopy (EDX) and white light interferometry; mechanical properties were analyzed by micro hardness measurement. The experiments reveal that the alignment of separated, elevated, dome-shaped spots on the steel surface is feasible. The geometrical properties as well as the mechanical properties are highly controllable by the laser parameters. The laser implanted spots show a mostly crack-free and pore-free bonding to the substrate material as well as a significant increase of micro hardness.

  15. Picosecond lasers: the next generation of short-pulsed lasers.

    Science.gov (United States)

    Freedman, Joshua R; Kaufman, Joely; Metelitsa, Andrea I; Green, Jeremy B

    2014-12-01

    Selective photothermolysis, first discussed in the context of targeted microsurgery in 1983, proposed that the optimal parameters for specific thermal damage rely critically on the duration over which energy is delivered to the tissue. At that time, nonspecific thermal damage had been an intrinsic limitation of all commercially available lasers, despite efforts to mitigate this by a variety of compensatory cooling mechanisms. Fifteen years later, experimental picosecond lasers were first reported in the dermatological literature to demonstrate greater efficacy over their nanosecond predecessors in the context of targeted destruction of tattoo ink. Within the last 4 years, more than a decade after those experiments, the first commercially available cutaneous picosecond laser unit became available (Cynosure, Westford, Massachusetts), and several pilot studies have demonstrated its utility in tattoo removal. An experimental picosecond infrared laser has also recently demonstrated a nonthermal tissue ablative capability in soft tissue, bone, and dentin. In this article, we review the published data pertaining to dermatology on picosecond lasers from their initial reports to the present as well as discuss forthcoming technology.

  16. Ionization of molecular hydrogen in ultrashort intense laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Vanne, Yulian V.

    2010-03-18

    A novel ab initio numerical approach is developed and applied that solves the time-dependent Schroedinger equation describing two-electron diatomic molecules (e.g. molecular hydrogen) exposed to an intense ultrashort laser pulse. The method is based on the fixed-nuclei and the non-relativistic dipole approximations and aims to accurately describe both correlated electrons in full dimensionality. The method is applicable for a wide range of the laser pulse parameters and is able to describe both few-photon and many-photon single ionization processes, also in a non-perturbative regime. A key advantage of the method is its ability to treat the strong-field response of the molecules with arbitrary orientation of the molecular axis with respect to the linear-polarized laser field. Thus, this work reports on the first successful orientation-dependent analysis of the multiphoton ionization of H{sub 2} performed by means of a full-dimensional numerical treatment. Besides the investigation of few-photon regime, an extensive numerical study of the ionization by ultrashort frequency-doubled Ti:sapphire laser pulses (400 nm) is presented. Performing a series of calculations for different internuclear separations, the total ionization yields of H{sub 2} and D{sub 2} in their ground vibrational states are obtained for both parallel and perpendicular orientations. A series of calculations for 800 nm laser pulses are used to test a popular simple interference model. Besides the discussion of the ab initio numerical method, this work considers different aspects related to the application of the strong-field approximation (SFA) for investigation of a strong-field response of an atomic and molecular system. Thus, a deep analysis of the gauge problem of SFA is performed and the quasistatic limit of the velocity-gauge SFA ionization rates is derived. The applications of the length-gauge SFA are examined and a recently proposed generalized Keldysh theory is criticized. (orig.)

  17. Simulation of intense short-pulse laser-plasma interaction

    Energy Technology Data Exchange (ETDEWEB)

    Yamagiwa, Mitsuru [Advanced Photon Research Center, Kansai Research Establishment, Japan Atomic Energy Research Inst., Kizu, Kyoto (Japan)

    2000-03-01

    We have completed the massive parallelization of a 2-dimensional giga-particle code and have achieved a 530-fold acceleration rate with 512 processing elements (PE's). Using this we have implemented a simulation of the interaction of a solid thin film and a high intensity laser and have discovered a phenomenon in which high quality short pulses from the far ultraviolet to soft X-rays are generated at the back surface of the thin layer. We have also introduced the atomic process database code (Hullac) and have the possibility for high precision simulations of X-ray laser radiation. With respect to laser acceleration we have the possibility to quantitatively evaluate relativistic self-focusing assumed to occur in higher intensity fields. Ion acceleration from a solid target and an underdense plasma irradiated by an intense and an ultra intense laser, respectively, has also been studied by particle-in-cell (PIC) simulations. (author)

  18. Comparative Study of Diode Laser Versus Neodymium-Yttrium Aluminum: Garnet Laser Versus Intense Pulsed Light for the Treatment of Hirsutism.

    Science.gov (United States)

    Puri, Neerja

    2015-01-01

    Lasers are widely used for the treatment of hirsutism. But the choice of the right laser for the right skin type is very important. Before starting with laser therapy, it is important to assess the skin type, the fluence, the pulse duration and the type of laser to be used. To compare the efficacy and side effects of Diode laser, Neodymium-yttrium aluminum - garnet (Nd: YAG) laser and intense pulsed light (IPL) on 30 female patients of hirsutism. Thirty female patients with hirsutism were selected for a randomised controlled study. The patients were divided into three groups of 10 patients each. In group I patients diode laser was used, in group II patients long pulsed Nd: YAG laser was used and in group III, IPL was used. The patients were evaluated and result graded according to a 4-point scale as excellent, >75% reduction; good, 50-75% reduction; fair; 25-50% reduction; and poor, diode laser group, followed by 35% hair reduction in the Nd: Yag laser group and 10% hair reduction in the IPL group. The percentage of hair reduction after four sessions of treatment was maximum (64%) in the diode laser group, followed by 62% hair reduction in the Nd: Yag laser group and 48% hair reduction in the IPL group. The percentage of hair reduction after eight sessions of treatment was maximum (92%) in the diode laser group, followed by 90% hair reduction in the Nd: YAG group and 70% hair reduction in the IPL group. To conclude for the Indian skin with dark hairs, the diode laser still stands the test of time. But, since the diode laser has a narrow margin of safety, proper pre and post-procedure cooling is recommended. Although, the side effects of Nd: YAG laser are less as compared to the diode laser, it is less efficacious as compared to the diode laser.

  19. Femtosecond few-cycle mid-infrared laser pulses

    DEFF Research Database (Denmark)

    Liu, Xing

    The few-cycle pulses of mid-infrared (mid-IR, wavelength 2-10 microns) have attracted increasing attention owing to their great potentials for high order harmonic generation, time-resolved spectroscopy, precision of cutting and biomedical science.In this thesis, mid-IR frequency conversion.......2 - 5.5 μm with only one fixed pump wavelength, a feature absent in Kerr media. Finally, we experimentally observe supercontinuum generation spanning 1.5 octaves, generated in a 10 mm long silicon-rich nitride waveguide pumped by 100 pJ femtosecond pulses from an erbium fiber laser. The waveguide has...

  20. Energy effective dual-pulse bispectral laser for EUV lithography

    Science.gov (United States)

    Zhevlakov, A. P.; Seisyan, R. P.; Bespalov, V. G.; Elizarov, V. V.; Grishkanich, A. S.; Kascheev, S. V.; Sidorov, I. S.

    2016-03-01

    The power consumption in the two-pulse bispectral primary source could be substantially decreased by replacing the SRS converters from 1.06 μm into 10.6 μm wavelength as the preamplifier cascades in CO2 laser channel at the same efficiency radiation of EUV source. The creation of high volume manufacturing lithography facilities with the technological standard of 10-20 nm is related to the implementation of resist exposure modes with pulse repetition rate of 100 kHz. Low power consumption of the proposed scheme makes it promising for the creation of LPP EUV sources.

  1. Alignment of symmetric top molecules by short laser pulses

    DEFF Research Database (Denmark)

    Hamilton, Edward; Seideman, Tamar; Ejdrup, Tine

    2005-01-01

    Nonadiabatic alignment of symmetric top molecules induced by a linearly polarized, moderately intense picosecond laser pulse is studied theoretically and experimentally. Our studies are based on the combination of a nonperturbative solution of the Schrodinger equation with femtosecond time......-resolved photofragment imaging. Using methyliodide and tert-butyliodide as examples, we calculate and measure the alignment dynamics, focusing on the temporal structure and intensity of the revival patterns, including their dependence on the pulse duration, and their behavior at long times, where centrifugal distortion...

  2. Infrared laser irradiation of dental enamel using submicrosecond laser pulses with and without an applied water layer: effect on bond strength to restorative materials

    Science.gov (United States)

    Sarma, Anupama V.; Staninec, Michal; Le, Charles Q.; Fried, Daniel

    2004-05-01

    Previous studies have shown that during IR laser irradiation at CO2 and Er:YAG laser wavelengths, residual particles of fused non-apatite calcium phosphate phases accumulate that may inhibit adhesion to restorative materials. A layer of water added to the enamel surface before ablation prevents the accumulation of such phases. The objective of this study was to investigate the influence of laser pulse duration and wavelength with and without the added water layer on the bond strength of composite to laser prepared enamel surfaces. The surfaces of bovine enamel were irradiated by three lasers systems: a 0.5-μs Er:YSGG laser. a 25-μs Er:YAG laser and a 5-μs TEA CO2 laser operating at 9.6-μm. A motion control system and a pressurized spray system incorporating a microprocessor controlled pulsed nozzle for water delivery, were used to ensure uniform treatment of the entire surface. There was no significant reduction in the shear-bond strength of enamel to composite for the shorter erbium laser pulses if a water-spray was not used, in contrast to previous results for the 200-μs free-running Er:YAG laser in which the water-spray resulted in significantly higher bond-strengths. Shear-bond strengths for both erbium laser systems were significantly higher than for the CO2 laser irradiated samples and the negative control (no acid-etch) but significantly lower than the positive control group (phosphoric acid-etch). The application of the water-spray markedly influenced the surface morphology for all three laser systems with the most uniform surface preparation being produced by the 25-μs Er:YAG laser and the 5-μs CO2 laser with the water-spray.

  3. Grism compressor for carrier-envelope phase-stable millijoule-energy chirped pulse amplifier lasers featuring bulk material stretcher.

    Science.gov (United States)

    Ricci, A; Jullien, A; Forget, N; Crozatier, V; Tournois, P; Lopez-Martens, R

    2012-04-01

    We demonstrate compression of amplified carrier-envelope phase (CEP)-stable laser pulses using paired transmission gratings and high-index prisms, or grisms, with chromatic dispersion matching that of a bulk material pulse stretcher. Grisms enable the use of larger bulk stretching factors and thereby higher energy pulses with lower B-integral in a compact amplifier design suitable for long-term CEP control.

  4. Dentin bond strength after ablation using a CO2 laser operating at high pulse repetition rates

    Science.gov (United States)

    Hedayatollahnajafi, Saba; Staninec, Michal; Watanabe, Larry; Lee, Chulsung; Fried, Daniel

    2009-02-01

    Pulsed CO2 lasers show great promise for the rapid and efficient ablation of dental hard tissues. Our objective was to demonstrate that CO2 lasers operated at high repetition rates can be used for the rapid removal of dentin without excessive thermal damage and without compromising adhesion to restorative materials. Human dentin samples (3x3mm2) were rapidly ablated with a pulsed CO2 laser operating at a wavelength of 9.3-µm, pulse repetition rate of 300-Hz and an irradiation intensity of 18-J/cm2. The bond strength to composite was determined by the modified single plane shear test. There were 8 test groups each containing 10 blocks: negative control (non-irradiated non-etched), positive control (non-irradiated acid-etched), and six laser treated groups (three etched and three non-etched sets). The first and second etched and non-etched sets were ablated at a speed of 25 mm/sec and 50 mm/sec with water, respectively. The third set was also ablated at 50 mm/sec without application of water during laser irradiation. Minimal thermal damage was observed on the dentin surfaces for which water cooling was applied. Bond strengths exceeded 20 MPa for laser treated surfaces that were acid-etched after ablation (25-mm/sec: 29.9-MPa, 50-mm/sec: 21.3-MPa). The water-cooled etched laser groups all produced significantly stronger bonds than the negative control (pbond strength than the positive control (pbond strength than the acid-etched control samples is clinically significant where durability of these bonded restoration supersedes high bond strength.

  5. Time-resolved beam profiler for pulsed lasers

    Science.gov (United States)

    Klick, David I.; Knight, Frederick K.

    1993-04-01

    A high-speed imaging device based on a streak camera has been demonstrated, which provides multiple images from non-repeatable transient events of time scale >= 1 ns. It can be employed for pulsed laser beam diagnostics, measuring laser beam spatial and temporal structure on a single-pulse basis. The system currently has angular resolution of 16 X 16 pixels, with a time resolution of 250 ps. The laser beam width is sized to fill the input optic, and the image is dissected by a square array of optical fibers. At the other end of the fiber optic image converter, the 256 fibers form a line array, which is input to the slit of a streak camera. The streak camera sweeps the input line across the output phosphor screen so that position is directly proportional to time. The resulting 2-D image (fiber position vs. time) at the phosphor is read by an intensified (SIT) vidicon TV tube, and the image is digitized and stored. A computer subsequently decodes the image, unscrambling the linear pixels into an angle-angle image at each time. We are left with a series of snapshots, each one depicting the laser beam spatial profile (intensity cross-section) at succeeding moments in time. The system can currently record several hundred images over a span of 25 to 400 ns. This detector can study lasers of pulse width >= 1 ns and with a visible wavelength (200 - 900 nm). Candidate lasers include doubled Nd:YAG, excimer, ruby, nitrogen, metal vapor, and Ti:Sapphire. The system could also be simply configured as an 8 X 8 element wavefront sensor to record the cross-sectional distribution of phase, as well as amplitude. Finally, suggestions for system improvement are detailed, and the ultimate limitations of the method in terms of spatial and temporal resolution are discussed.

  6. Gain dynamics of a free-space nitrogen laser pumped by circularly polarized femtosecond laser pulses.

    Science.gov (United States)

    Yao, Jinping; Xie, Hongqiang; Zeng, Bin; Chu, Wei; Li, Guihua; Ni, Jielei; Zhang, Haisu; Jing, Chenrui; Zhang, Chaojin; Xu, Huailiang; Cheng, Ya; Xu, Zhizhan

    2014-08-11

    We experimentally demonstrate ultrafast dynamic of generation of the 337-nm nitrogen laser by injecting an external seed pulse into a femtosecond laser filament pumped by a circularly polarized laser pulse. In the pump-probe scheme, it is revealed that the population inversion between the C(3)Π(u) and B(3)Π(g) states of N(2) for the free-space 337-nm laser is firstly built up on the timescale of several picoseconds, followed by a relatively slow decay on the timescale of tens of picoseconds, depending on the nitrogen gas pressure. By measuring the intensities of 337-nm signal from nitrogen gas mixed with different concentrations of oxygen gas, it is also found that oxygen molecules have a significant quenching effect on the nitrogen laser signal. Our experimental observations agree with the picture of electron-impact excitation.

  7. INTERACTION OF LASER RADIATION WITH MATTER: Influence of a target on operation of a pulsed CO2 laser emitting microsecond pulses

    Science.gov (United States)

    Baranov, V. Yu; Dolgov, V. A.; Malyuta, D. D.; Mezhevov, V. S.; Semak, V. V.

    1987-12-01

    The profile of pulses emitted by a TEA CO2 laser with an unstable resonator changed as a result of interaction of laser radiation with the surface of a metal in the presence of a breakdown plasma. This influence of a target on laser operation and its possible applications in laser processing of materials are analyzed.

  8. Tunable CO2 laser system with subnanosecond-pulse-train output

    Science.gov (United States)

    Kimura, W. D.

    2017-02-01

    A CO2 laser system has been demonstrated that generates a train of subnanosecond pulses tunable over the P and R branches of the CO2 laser spectrum at 9-11 μm. It utilizes optical free induction decay to generate a single 100-ps laser pulse from a tunable transverse-excited-atmospheric CO2 laser. This laser pulse is injection-seeded into a high-pressure CO2 oscillator whose output consists of a train of amplified 100-ps pulses with maximum pulse energy of 30 mJ, corresponding to a peak power of 300 MW. The 100-ps, tunable, infrared laser pulses are needed for a new technique to remotely detect atmospheric gaseous molecules, which relies on the train of CO2 laser pulses selectively exciting the target molecules whose presence is then revealed using a separate terahertz probe beam.

  9. Numerical investigation of vessel heating using a copper vapor laser and a pulsed dye laser in treating vascular skin lesions

    Science.gov (United States)

    Pushkareva, A. E.; Ponomarev, I. V.; Isaev, A. A.; Klyuchareva, S. V.

    2018-02-01

    A computer simulation technique was employed to study the selective heating of a tissue vessel using emission from a pulsed copper vapor laser and a pulsed dye laser. The depth and size of vessels that could be selectively and safely removed were determined for the lasers under examination.

  10. Pulsed laser deposition of niobium nitride thin films

    Energy Technology Data Exchange (ETDEWEB)

    Farha, Ashraf Hassan, E-mail: ahass006@odu.edu; Elsayed-Ali, Hani E., E-mail: helsayed@odu.edu [Department of Electrical and Computer Engineering, Old Dominion University, Norfolk, VA 23529 (United States); Applied Research Center, Jefferson National Accelerator Facility, Newport News, VA 23606 (United States); Department of Physics, Faculty of Science, Ain Shams University, Cairo 11566 (Egypt); Ufuktepe, Yüksel, E-mail: ufuk@cu.edu.tr [Department of Physics, University of Cukurova, 01330 Adana (Turkey); Myneni, Ganapati, E-mail: rao@jlab.org [Thomas Jefferson National Accelerator Facility, Newport News, Virginia 23606 (United States)

    2015-12-04

    Niobium nitride (NbN{sub x}) films were grown on Nb and Si(100) substrates using pulsed laser deposition. NbN{sub x} films were deposited on Nb substrates using PLD with a Q-switched Nd:YAG laser (λ = 1064 nm, ∼40 ns pulse width, and 10 Hz repetition rate) at different laser fluences, nitrogen background pressures and deposition substrate temperatures. When all the fabrication parameters are fixed, except for the laser fluence, the surface roughness, nitrogen content, and grain size increase with increasing laser fluence. Increasing nitrogen background pressure leads to a change in the phase structure of the NbN{sub x} films from mixed β-Nb{sub 2}N and cubic δ-NbN phases to single hexagonal β-Nb{sub 2}N. The substrate temperature affects the preferred orientation of the crystal structure. The structural and electronic, properties of NbN{sub x} deposited on Si(100) were also investigated. The NbN{sub x} films exhibited a cubic δ-NbN with a strong (111) orientation. A correlation between surface morphology, electronic, and superconducting properties was found. The observations establish guidelines for adjusting the deposition parameters to achieve the desired NbN{sub x} film morphology and phase.

  11. Effect of Er:YAG laser pulse duration on the shear bond strength of bleached dentin

    Science.gov (United States)

    Yu, Ping; Yu, Dandan; Zhao, Peng; Xu, Zhou; Gao, Shanshan

    2017-11-01

    The influence of different Er:YAG laser pulse durations on the shear bond strength (SBS) of bleached dentin was investigated in this study. In total, 176 crowns of extracted human premolars were cut horizontally, embedded and ground to expose the sound dentin. Of these, 132 specimens were bleached with 12% hydrogen peroxide (HP) and divided into three groups, irradiated by an Er:YAG laser with different pulse lengths of 50 µs super short pulse (SSP), 100 µs moderate short pulse (MSP) and 300 µs short pulse (SP), respectively. The energy density of the three groups was the same at about 15.73 J cm‑2 for each. Then, each group was further divided into two subgroups according to whether it had been etched with 37% phosphoric acid or not. The control group (N  =  22) was bleached and etched with acid while the blank group (N  =  22) was just etched with acid. The surface morphology of the dentin was observed using scanning electron microscopy (SEM). The SBS of the composite resin to the conditioned dentin was tested with a universal testing machine. It was found that the SBS of the dentin significantly decreased after bleaching treatment, while it was possible to restore it using Er:YAG laser irradiation. Lasers with various pulse durations led to different surface morphologies but had no effect on the SBS. The SSP laser was more suitable on account of it resulting in less thermal damage, and additional acid etching was not necessary for the irradiated bleached dentin in the clinic because it could not further improve the SBS value.

  12. High pulse energy, high beam quality microsecond-pulse Ti:sapphire laser at 819.7 nm

    Science.gov (United States)

    Xu, Chang; Guo, Chuan; Yu, Hai-Bo; Wang, Zhi-Min; Zuo, Jun-Wei; Xia, Yuan-Qin; Bian, Qi; Bo, Yong; Gao, Hong-Wei; Guo, Ya-Ding; Zhang, Sheng; Cui, Da-Fu; Peng, Qin-Jun; Xu, Zu-Yan

    2017-03-01

    In this letter, a high pulse energy and high beam quality 819.7 nm Ti:sapphire laser pumped by a frequency-doubled Nd:YAG laser is demonstrated. At incident pump energy of 774 mJ, the maximum output energy of 89 mJ at 819.7 nm with a pulse width of 100 μs is achieved at a repetition rate of 5 Hz. To the best of our knowledge, this is the highest pulse energy at 819.7 nm with pulse width of hundred microseconds for a Ti:sapphire laser. The beam quality factor M 2 is measured to be 1.18. This specific wavelength with the high pulse energy and high beam quality at 819.7 nm is a promising light source to create a polychromatic laser guide star together with a home-made 589 nm laser via exciting the sodium atoms in the mesospheric atmosphere.

  13. Picosecond Laser Pulse Optical Density of Three 1060-NM Filters.

    Science.gov (United States)

    1980-12-01

    pul- ses. These included a dyed glass plate (Schott KG-3), a polymethyl methacrylate plate ( PMMA ) developed for the Air Force for 1060-nm- specific...Schott KG-3), a polymethyl methacrylate plate ( PMMA ) developed for the Air Force for 1060-nm-specific visors, and a dielectric-coated laser cavity... Ocular tissue damage due to ultrashort 1060-nm light pulses from a mode-locked Nd:glass laser. Appl Opt 14:1759-1761 (1975). 4. Taboada, J., and D. D

  14. Resonant infrared pulsed laser deposition of thin biodegradable polymer films

    DEFF Research Database (Denmark)

    Bubb, D.M.; Toftmann, B.; Haglund Jr., R.F.

    2002-01-01

    Thin films of the biodegradable polymer poly(DL-lactide-co-glycolide) (PLGA) were deposited using resonant infrared pulsed laser deposition (RIR-PLD). The output of a free-electron laser was focused onto a solid target of the polymer, and the films were deposited using 2.90 (resonant with O...... absorbance spectrum of the films is nearly identical with that of the native polymer, the average molecular weight of the films is a little less than half that of the starting material. Potential strategies for defeating this mass change are discussed....

  15. Short-Pulse Laser-Matter Computational Workshop Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Town, R; Tabak, M

    2004-11-02

    For three days at the end of August 2004, 55 plasma scientists met at the Four Points by Sheraton in Pleasanton to discuss some of the critical issues associated with the computational aspects of the interaction of short-pulse high-intensity lasers with matter. The workshop was organized around the following six key areas: (1) Laser propagation/interaction through various density plasmas: micro scale; (2) Anomalous electron transport effects: From micro to meso scale; (3) Electron transport through plasmas: From meso to macro scale; (4) Ion beam generation, transport, and focusing; (5) ''Atomic-scale'' electron and proton stopping powers; and (6) K{alpha} diagnostics.

  16. Wetting ability modifications in biocompatible polymers induced by pulsed lasers

    Science.gov (United States)

    Scolaro, C.; Torrisi, L.; Cutroneo, M.; Velardi, L.

    2014-04-01

    Wetting ability was measured in the surface of different biocompatible polymers, such as mylar, polyethylene, poly-methyl-methacrylate and teflon. Nanosecond pulse lasers at intensities of the order of 108 W/cm2 were employed at different doses to irradiate the polymeric surfaces and to induce wetting ability modifications due to the chemical and physical surface changes vs. irradiation time and laser wavelength. In particular, the contact angle as a function of the surface roughness was investigated, as will be presented and discussed.

  17. Pyramidal growth of ceria nanostructures by pulsed laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Bârcă, E.S. [Pitesti University, Faculty of Mechanics and Technology, 110040 Pitesti, Arges (Romania); Filipescu, M., E-mail: mihaela.filipescu@gmail.com [National Institute for Lasers, Plasma and Radiation Physics, 077125 Magurele (Romania); Luculescu, C.; Birjega, R.; Ion, V.; Dumitru, M. [National Institute for Lasers, Plasma and Radiation Physics, 077125 Magurele (Romania); Nistor, L.C. [National Institute of Materials Physics, 077125 Magurele, Ilfov (Romania); Stanciu, G. [National Institute for Lasers, Plasma and Radiation Physics, 077125 Magurele (Romania); University Politehnica of Bucharest, Faculty of Applied Chemistry and Material Science, 011061 Bucharest (Romania); Abrudeanu, M. [Pitesti University, Faculty of Mechanics and Technology, 110040 Pitesti, Arges (Romania); Munteanu, C. [Technical University “Gheorghe Asachi” of Iasi, Faculty of Mechanics, 700050, Iasi (Romania); Dinescu, M. [National Institute for Lasers, Plasma and Radiation Physics, 077125 Magurele (Romania)

    2016-02-15

    Graphical abstract: - Highlights: • Growth of ceria thin films with pyramidal morphology suitable for catalytic and sensor applications. • Ceria thin films with hierarchical structures combination of columnar and dendritic growth and crystalline cubic structure are obtained by pulsed laser deposition. • High substrate temperature influences the appearance of these hierarchical structures. - Abstract: We report in this paper on the deposition and characterization of CeO{sub 2} nanostructured thin films with hierarchical morphology. Micro-sized ceria powder (CeO{sub 2}, 99.9% purity) was pressed to obtain a ceramic target. An ArF laser working at 193 nm irradiated the target in controlled oxygen gas flow at constant pressure (0.1 mbar). Silicon wafers used as substrates for thin films were heated at different temperatures, up to 773 K. The influence of substrate temperature on the structure and surface morphology of ceria thin films was studied by X-ray diffraction (XRD), transmission electron microscopy (TEM), Raman spectroscopy and scanning electron microscopy (SEM). The refractive indices and information about roughness and thickness were revealed by spectroellipsometry. Crystalline cubic ceria thin films exhibiting a hierarchical structure that combines columnar and dendritic growth were obtained at temperatures above 473 K. For the samples obtained at 773 K, columns ending in pyramidal formations with sharp edges and sizes of hundreds of nanometers were observed, indicating a high crystallinity of the layer. XRD analysis reveals a consistent increase of the X-ray coherence length/crystallite size along the [111] direction with increasing temperature. Using a semi-empirical formula, Raman crystallites sizes were calculated and it was found that size increases with the temperature increasing. The spectroellipsometry investigations evidenced the increasing of refractive index with the substrate temperature increase. High surface roughness and pyramidal

  18. Preface to the Special Issue on short pulse fiber lasers

    Science.gov (United States)

    Delavaux, Jean-Marc P.; Grelu, Philippe; Pu, Wang; Ilday, Fatih Ömer

    2014-12-01

    In the last two decades the fiber laser has evolved from a laboratory curiosity to a viable tool in an increasing number of applications in such diverse areas as material processing, atmospheric monitoring, high energy physics, medicine, telecommunications, and defense. The reasons for the growing acceptance of fiber lasers lie in the combination of their many attractive features. Indeed, fiber lasers are together power efficient, compact, light weight, versatile and reliable. Initially, the development of fiber laser technology was led to challenge the dominance of well entrenched solid state lasers used in the lucrative manufacturing industry. Traditionally, the emission wavelength band of interest was mostly limited to the near infrared (NIR) region (i.e. from 1 to 1.6 μm). More recently, extensive fiber laser R&D advances have extended the laser applications to a broader spectrum, from the ultra violet (UV) to the mid-infrared (Mid-IR) wavelength region, and investigated the specific advantages associated with different pulse widths, from ns to fs, and different operating regimes.

  19. Two-photon imaging using adaptive phase compensated ultrashort laser pulses.

    Science.gov (United States)

    Xi, Peng; Andegeko, Yair; Pestov, Dmitry; Lovozoy, Vadim V; Dantus, Marcos

    2009-01-01

    An adaptive pulse shaper controlled by multiphoton intrapulse interference phase scanning (MIIPS) was used, together with a prism-pair, to measure and cancel high-order phase distortions introduced by a high-numerical-aperture objective and other dispersive elements of a two-photon laser-scanning microscope. The delivery of broad-bandwidth (approximately 100 nm), sub-12-fs pulses was confirmed by interferometric autocorrelation measurements at the focal plane. A comparison of two-photon imaging with transform-limited and second-order-dispersion compensated laser pulses of the same energy showed a 6-to-11-fold improvement in the two-photon excitation fluorescence signal when applied to cells and tissue, and up to a 19-fold improvement in the second harmonic generation signal from a rat tendon specimen.

  20. Note: 15-fs, 15-μJ green pulses from two-stage temporal compressor of ytterbium laser pulses.

    Science.gov (United States)

    Konyashchenko, A V; Kostryukov, P V; Losev, L L; Tenyakov, S Yu

    2012-10-01

    15-fs, 15-μJ light pulses at the central wavelength of 515 nm were generated by two-stage nonlinear compression of 300-fs, 150-μJ ytterbium laser pulses. The compression was based on the pulse spectrum broadening by self-phase modulation in gas filled capillary and second harmonic generation in crystal.

  1. Rapid microfabrication of transparent materials using filamented femtosecond laser pulses

    Science.gov (United States)

    Butkus, S.; Gaižauskas, E.; Paipulas, D.; Viburys, Ž.; Kaškelyė, D.; Barkauskas, M.; Alesenkov, A.; Sirutkaitis, V.

    2014-01-01

    Microfabrication of transparent materials using femtosecond laser pulses has showed good potential towards industrial application. Maintaining pulse energies exceeding the critical self-focusing threshold by more than 100-fold produced filaments that were used for micromachining purposes. This article demonstrates two different micromachining techniques using femtosecond filaments generated in different transparent media (water and glass). The stated micromachining techniques are cutting and welding of transparent samples. In addition, cutting and drilling experiments were backed by theoretical modelling giving a deeper insight into the whole process. We demonstrate cut-out holes in soda-lime glass having thickness up to 1 mm and aspect ratios close to 20, moreover, the fabrication time is of the order of tens of seconds, in addition, grooves and holes were fabricated in hardened 1.1 mm thick glass (Corning Gorilla glass). Glass welding was made possible and welded samples were achieved after several seconds of laser fabrication.

  2. Optical modulation of astrocyte network using ultrashort pulsed laser

    Science.gov (United States)

    Yoon, Jonghee; Ku, Taeyun; Chong, Kyuha; Ryu, Seung-Wook; Choi, Chulhee

    2012-03-01

    Astrocyte, the most abundant cell type in the central nervous system, has been one of major topics in neuroscience. Even though many tools have been developed for the analysis of astrocyte function, there has been no adequate tool that can modulates astrocyte network without pharmaceutical or genetic interventions. Here we found that ultrashort pulsed laser stimulation can induce label-free activation of astrocytes as well as apoptotic-like cell death in a dose-dependent manner. Upon irradiation with high intensity pulsed lasers, the irradiated cells with short exposure time showed very rapid mitochondria fragmentation, membrane blebbing and cytoskeletal retraction. We applied this technique to investigate in vivo function of astrocyte network in the CNS: in the aspect of neurovascular coupling and blood-brain barrier. We propose that this noninvasive technique can be widely applied for in vivo study of complex cellular network.

  3. Intrastromal refractive sugery with ultrashort laser pulses in living animals

    Science.gov (United States)

    Heisterkamp, Alexander; Mamom, Thanongsak; Kermani, Omid; Drommer, Wolfgang; Welling, Herbert; Ertmer, Wolfgang; Lubatschowski, Holger

    2002-06-01

    In order to perform refractive surgery, fs-laser pulses of 130-fs pulse duration were focused into animal cornea. By focusing the radiation down to spot-sizes of 5 micrometers , very precise cuts could be achieved inside the treated eyes, accompanied with minimum collateral damage to the tissue by thermal or mechanical effects. Due to these low side effects, micrometers -cutting precisions at preparing of corneal flaps and lenticules can be achieved. Thus, animal studies with 8 living rabbits were performed, in which intrastromal lenticules and flaps were created and extracted. Wound healing reactions were studied by histo- pathological analysis of the treated eyes in intervals at one, 7, 14 and 28 days after surgery. The treated eyes showed mild wound healing reactions with comparable results to what is known from Excimer-LASIK. Moreover the use of the fs-laser offered new possibilities in preparation of corneal flaps, providing advantages to the use of the mechanical keratome.

  4. Nonlinear electron emission in ultrashort laser pulses and rescattering suppression

    Science.gov (United States)

    Mikhin, E. A.; Preobrazhenskii, M. A.; Golovinski, P. A.

    2017-11-01

    The process of nonlinear electron emission from a metal surface under the action of femtosecond laser pulse with moderate intensity ~1011 W/cm2 is considered. One-dimensional model is formulated, taking into account the advantage of the p-polarized light in the nonlinear emission. The time dependent Schrödinger equation with fixed equilibrium boundary conditions is solved in the half-space using the Laplace transform technique. The energy spectrum of emitted electrons is presented, including analysis of dependence on the laser pulse parameters. In the framework of classical mechanics, the impact of additional dc electric field on the rescattering of emitted electron on the metal surface is investigated. The model reproduces the fiches of electron energy distribution and can be used at arbitrary Keldysh parameters.

  5. [A clinical observation of pericoronitis treatment with pulse semiconductor laser].

    Science.gov (United States)

    Lu, Shan; Fang, Yuan

    2004-08-01

    In order to valuate the effect of pericoronitis treated with pulse semiconductor laser. As a treatment group, 24 ones drawn ramdomly from 48 cases of pericoronitis were given periodontal radiation, point-radiation therapy and pharmacotherapy as well. While another 24 cases as a contrast group were given pharmacotherapy only. On the 3rd day and the 5th day the degree of pain and restriction of mouth opening of the two groups were graded, contrasted and processed by Ridit statistics. Result, The therapy group gained more notable effect in pain-relieving and mouth-opening-improving than the contrast group. Because of no damage, handy and can be done easily, be definite in curative effect, Pulse semiconductor laser treatment pericoronitis deserves popularizing.

  6. Selective bond breakage within the HOD molecule using optimized femtosecond ultraviolet laser pulses

    DEFF Research Database (Denmark)

    Tiwari, Ashwani Kumar; Møller, Klaus Braagaard; Henriksen, Niels Engholm

    2008-01-01

    With the HOD molecule initially in its vibrational ground state, we theoretically analyze the laser-induced control of the OD/OH branching ratio D+OH H+OD in the first absorption band. In the weak-field limit, any form of UV-pulse shaping control leads to a branching ratio larger than similar to 2....... We obtain in the strong-field limit (peak intensities similar to 10 TW/cm(2)) a branching ratio significantly less than 2. The optimized pulses operate by a pump-dump-pump mechanism, where the dumping to the electronic ground state creates nonstationary vibrational states in HOD....

  7. Desorption by Femtosecond Laser Pulses : An Electron-Hole Effect?

    OpenAIRE

    D. M., NEWNS; T. F., HEINZ; J. A., MISEWICH; IBM Research Division, T. J. Watson Research Center; IBM Research Division, T. J. Watson Research Center; IBM Research Division, T. J. Watson Research Center

    1992-01-01

    Desorption of molecules from metal surfaces induced by femtosecond visible laser pulses has been reported. Since the lattice temperature rise is insufficient to explain desorption, an electronic mechanism is clearly responsible. It is shown that a theory based on direct coupling between the center-of-mass degree of freedom of the adsorbate and the electron-hole excitations of the substrate provides a satisfactory explanation of the various experimental findings.

  8. Pulsed laser deposition and characterisation of thin superconducting films

    Energy Technology Data Exchange (ETDEWEB)

    Morone, A. [CNR, zona industriale di Tito Scalo, Potenza (Italy). Istituto per i Materiali Speciali

    1996-09-01

    Same concepts on pulsed laser deposition of thin films will be discussed and same examples of high transition temperature (HTc) BiSrCaCuO (BISCO) and low transition temperature NbN/MgO/NbN multilayers will be presented. X-ray and others characterizations of these films will be reported and discussed. Electrical properties of superconducting thin films will be realized as a function of structural and morphological aspect.

  9. Volumetric graphics in liquid using holographic femtosecond laser pulse excitations

    Science.gov (United States)

    Kumagai, Kota; Hayasaki, Yoshio

    2017-06-01

    Much attention has been paid to the development of three-dimensional volumetric displays in the fields of optics and computer graphics, and it is a dream of we display researchers. However, full-color volumetric displays are challenging because many voxels with different colors have to be formed to render volumetric graphics in real three-dimensional space. Here, we show a new volumetric display in which microbubble voxels are three-dimensionally generated in a liquid by focused femtosecond laser pulses. Use of a high-viscosity liquid, which is the key idea of this system, slows down the movement of the microbubbles, and as a result, volumetric graphics can be displayed. This "volumetric bubble display" has a wide viewing angle and simple refresh and requires no addressing wires because it involves optical access to transparent liquid and achieves full-color graphics composed on light-scattering voxels controlled by illumination light sources. In addition, a bursting of bubble graphics system using an ultrasonic vibrator also has been demonstrated. This technology will open up a wide range of applications in three-dimensional displays, augmented reality and computer graphics.

  10. Interaction Mechanisms of Cavitation Bubbles Induced by Spatially and Temporally Separated fs-Laser Pulses

    Science.gov (United States)

    Tinne, Nadine; Kaune, Brigitte; Krüger, Alexander; Ripken, Tammo

    2014-01-01

    The emerging use of femtosecond lasers with high repetition rates in the MHz regime together with limited scan speed implies possible mutual optical and dynamical interaction effects of the individual cutting spots. In order to get more insight into the dynamics a time-resolved photographic analysis of the interaction of cavitation bubbles is presented. Particularly, we investigated the influence of fs-laser pulses and their resulting bubble dynamics with various spatial as well as temporal separations. Different time courses of characteristic interaction effects between the cavitation bubbles were observed depending on pulse energy and spatio-temporal pulse separation. These ranged from merely no interaction to the phenomena of strong water jet formation. Afterwards, the mechanisms are discussed regarding their impact on the medical application of effective tissue cutting lateral to the laser beam direction with best possible axial precision: the mechanical forces of photodisruption as well as the occurring water jet should have low axial extend and a preferably lateral priority. Furthermore, the overall efficiency of energy conversion into controlled mechanical impact should be maximized compared to the transmitted pulse energy and unwanted long range mechanical side effects, e.g. shock waves, axial jet components. In conclusion, these experimental results are of great importance for the prospective optimization of the ophthalmic surgical process with high-repetition rate fs-lasers. PMID:25502697

  11. Interaction mechanisms of cavitation bubbles induced by spatially and temporally separated fs-laser pulses.

    Directory of Open Access Journals (Sweden)

    Nadine Tinne

    Full Text Available The emerging use of femtosecond lasers with high repetition rates in the MHz regime together with limited scan speed implies possible mutual optical and dynamical interaction effects of the individual cutting spots. In order to get more insight into the dynamics a time-resolved photographic analysis of the interaction of cavitation bubbles is presented. Particularly, we investigated the influence of fs-laser pulses and their resulting bubble dynamics with various spatial as well as temporal separations. Different time courses of characteristic interaction effects between the cavitation bubbles were observed depending on pulse energy and spatio-temporal pulse separation. These ranged from merely no interaction to the phenomena of strong water jet formation. Afterwards, the mechanisms are discussed regarding their impact on the medical application of effective tissue cutting lateral to the laser beam direction with best possible axial precision: the mechanical forces of photodisruption as well as the occurring water jet should have low axial extend and a preferably lateral priority. Furthermore, the overall efficiency of energy conversion into controlled mechanical impact should be maximized compared to the transmitted pulse energy and unwanted long range mechanical side effects, e.g. shock waves, axial jet components. In conclusion, these experimental results are of great importance for the prospective optimization of the ophthalmic surgical process with high-repetition rate fs-lasers.

  12. Interaction mechanisms of cavitation bubbles induced by spatially and temporally separated fs-laser pulses.

    Science.gov (United States)

    Tinne, Nadine; Kaune, Brigitte; Krüger, Alexander; Ripken, Tammo

    2014-01-01

    The emerging use of femtosecond lasers with high repetition rates in the MHz regime together with limited scan speed implies possible mutual optical and dynamical interaction effects of the individual cutting spots. In order to get more insight into the dynamics a time-resolved photographic analysis of the interaction of cavitation bubbles is presented. Particularly, we investigated the influence of fs-laser pulses and their resulting bubble dynamics with various spatial as well as temporal separations. Different time courses of characteristic interaction effects between the cavitation bubbles were observed depending on pulse energy and spatio-temporal pulse separation. These ranged from merely no interaction to the phenomena of strong water jet formation. Afterwards, the mechanisms are discussed regarding their impact on the medical application of effective tissue cutting lateral to the laser beam direction with best possible axial precision: the mechanical forces of photodisruption as well as the occurring water jet should have low axial extend and a preferably lateral priority. Furthermore, the overall efficiency of energy conversion into controlled mechanical impact should be maximized compared to the transmitted pulse energy and unwanted long range mechanical side effects, e.g. shock waves, axial jet components. In conclusion, these experimental results are of great importance for the prospective optimization of the ophthalmic surgical process with high-repetition rate fs-lasers.

  13. Optical Characterization of SERS Substrates Based on Porous Au Films Prepared by Pulsed Laser Deposition

    Directory of Open Access Journals (Sweden)

    V. V. Strelchuk

    2015-01-01

    Full Text Available The SERS (surface enhanced Raman spectroscopy substrates based on nanocomposite porous films with gold nanoparticles (Au NPs arrays were formed using the method of the pulsed laser deposition from the back low-energy flux of erosion torch particles on the glass substrate fixed at the target plain. The dependencies of porosity, and morphology of the surface of the film regions located near and far from the torch axis on the laser ablation regime, laser pulses energy density, their number, and argon pressure in the vacuum chamber, were ascertained. The Au NPs arrays with the controllable extinction spectra caused by the local surface plasmon resonance were prepared. The possibility of the formation of SERS substrates for the detection of the Rhodamine 6G molecules with the concentration 10−10 Mol/L with the enhancement factor 4·107 was shown.

  14. Digital gate pulse generator for cycloconverter control

    Science.gov (United States)

    Klein, Frederick F.; Mutone, Gioacchino A.

    1989-01-01

    The present invention provides a digital gate pulse generator which controls the output of a cycloconverter used for electrical power conversion applications by determining the timing and delivery of the firing pulses to the switching devices in the cycloconverter. Previous gate pulse generators have been built with largely analog or discrete digital circuitry which require many precision components and periodic adjustment. The gate pulse generator of the present invention utilizes digital techniques and a predetermined series of values to develop the necessary timing signals for firing the switching device. Each timing signal is compared with a reference signal to determine the exact firing time. The present invention is significantly more compact than previous gate pulse generators, responds quickly to changes in the output demand and requires only one precision component and no adjustments.

  15. Fractional high-harmonic combs by attosecond-precision split-spectrum pulse control

    Directory of Open Access Journals (Sweden)

    Laux Martin

    2013-03-01

    Full Text Available Few-cycle laser fields enable pulse-shaping control of high-order harmonic generation by time delaying variable broadband spectral sections. We report the experimental generation of fractional (noninteger high-harmonic combs by the controlled interference of two attosecond pulse trains. Additionally the energy of the high harmonics is strongly tuned with the relative time delay. We quantify the tuning to directly result from the controlled variation of the instantaneous laser frequency at the shaped driver pulse intensity maximum.

  16. Dielectrophoretic focusing integrated pulsed laser activated cell sorting

    Science.gov (United States)

    Zhu, Xiongfeng; Kung, Yu-Chun; Wu, Ting-Hsiang; Teitell, Michael A.; Chiou, Pei-Yu

    2017-08-01

    We present a pulsed laser activated cell sorter (PLACS) integrated with novel sheathless size-independent dielectrophoretic (DEP) focusing. Microfluidic fluorescence activated cell sorting (μFACS) systems aim to provide a fully enclosed environment for sterile cell sorting and integration with upstream and downstream microfluidic modules. Among them, PLACS has shown a great potential in achieving comparable performance to commercial aerosol-based FACS (>90% purity at 25,000 cells sec-1). However conventional sheath flow focusing method suffers a severe sample dilution issue. Here we demonstrate a novel dielectrophoresis-integrated pulsed laser activated cell sorter (DEP-PLACS). It consists of a microfluidic channel with 3D electrodes laid out to provide a tunnel-shaped electric field profile along a 4cmlong channel for sheathlessly focusing microparticles/cells into a single stream in high-speed microfluidic flows. All focused particles pass through the fluorescence detection zone along the same streamline regardless of their sizes and types. Upon detection of target fluorescent particles, a nanosecond laser pulse is triggered and focused in a neighboring channel to generate a rapidly expanding cavitation bubble for precise sorting. DEP-PLACS has achieved a sorting purity of 91% for polystyrene beads at a throughput of 1,500 particle/sec.

  17. Extreme dynamic compression with a low energy laser pulse

    Science.gov (United States)

    Armstrong, Michael R.; Crowhurst, Jonathan C.; Zaug, Joseph M.; Radousky, Harry B.

    2017-01-01

    Here we review the scaling of pulse energy with duration for sub-ns laser-driven dynamic compression experiments, which suggests that extreme pressures (multiple Mbar) might be achieved in rapidly equilibrating materials with substantially lower energy than used in traditional experiments. For instance, conventional scaling of pressure with laser intensity indicates that pressures well into the multiple Mbar range should be accessible by compressing with a hundreds of picosecond duration drive pulse with some tens of mJ of energy - orders of magnitude less than required for conventional experiments. Via a related scaling argument, we also show that the throughput of time-resolved pulsed x-ray dynamic compression experiments (such as those performed at x-ray free electron lasers) varies as the inverse square of the time scale of the experiment. The strong variation of throughput with the scale of the experiment should be a significant consideration in the design of such experiments - to obtain high throughput, the time scale of compression should be no longer than required (via material equilibration) to achieve the desired final material state.

  18. Phonatory outcome of 585 nm/pulsed-dye laser in the management of glottic leukoplakia.

    Science.gov (United States)

    Park, Young Min; Jo, Kwang Hee; Hong, Hyun Jun; Choi, Hong-Shik

    2014-10-01

    Vocal cord mucosectomy using pulsed-dye laser was assessed for its ability to completely remove lesions without deterioration of vocal quality in cases of vocal cord leukoplakia. To confirm the validity of a pulsed-dye laser, we retrospectively analyzed the treatment outcomes of patients who received surgery preceded by pulsed-dye laser and compared these with the outcomes of patients who received vocal cord mucosectomy using CO2 laser. Between February 2007 and June 2012, 36 patients were enrolled. Seventeen patients received vocal cord treatment with a CO2 laser and 19 patients received operation with a pulsed-dye laser. To evaluate voice status, acoustic wave form analysis and electroglottography were done, and voice handicap index was measured before and after the operation. The entire lesion was removed in all patients. Compared to preoperative vocal parameters, the postoperative values for jitter were only improved in the pulsed-dye laser group. On stroboscopic findings, a diminution or lack of mucosal wave was observed in more CO2 laser cases than pulsed-dye laser cases. Significant improvement in voice handicap index results was only observed in the pulsed-dye laser group. Although long-term results with more patients are required to establish the validity of pulsed-dye laser, this study confirmed the merits of pulsed-dye laser for the en-bloc removal of vocal cord leukoplakia and improved voice outcome. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  19. Femtosecond pulse shaping for phase and morphology control in PLD: Synthesis of cubic SiC

    Science.gov (United States)

    Ristoscu, C.; Socol, G.; Ghica, C.; Mihailescu, I. N.; Gray, D.; Klini, A.; Manousaki, A.; Anglos, D.; Fotakis, C.

    2006-04-01

    Pulse shaping introduces the method that makes possible the production of tunable arbitrary shaped pulses. We extend this method to control the prevalent growth of cubic SiC films on Si (1 0 0) substrates by pulsed laser deposition at temperatures around 973 K from a SiC target in vacuum. We used a laser system generating 200 fs pulses duration at 800 nm with 600 μJ at 1 kHz. The obtained structures are investigated by electron microscopy, X-ray diffraction and profilometry. We observed grains embedded in an amorphous texture, characteristic in our opinion to the depositions obtained with very short pulses. We present a comparison of deposited films with and without pulse shaping. Pulse shaping promotes increased crystallization and results in the deposition of thin structures of cubic SiC with a strongly reduced density of particulates, under similar deposition conditions.

  20. Coherent control of light-pulse propagation in a Raman induced grating

    Science.gov (United States)

    Arkhipkin, V. G.; Myslivets, S. A.

    2017-05-01

    We study light-pulse propagation in a dynamically controllable periodic structure (grating) resulting from Raman interaction of a weak probe pulse with a standing-wave pump and a second control laser field in N-type four-level atomic media. The grating is induced due to periodic spatial modulation of the Raman gain in a standing pump field (Raman gain grating). We show that it is possible to control both the probe pulse amplitude and the group velocity of the pulse from subluminal to superluminal by varying the pump or control field. Such a grating is of interest for all-optical switches and transistors.

  1. LASER PHYSICS: Self-stabilization of ultrashort pulses emitted by a neodymium phosphate glass laser

    Science.gov (United States)

    Mavritskiĭ, O. B.; Petrovskiĭ, A. N.

    1987-07-01

    An investigation was made of the emission spectra of a neodymium phosphate glass laser during various stages of formation of ultrashort pulses. The kinetics of the spectrum of free lasing with passive mode locking was observed first. Considerable changes in the spectrum were observed for successive free-lasing spikes, which made it impossible to achieve self-stabilization of the ultrashort pulse duration. The spectrum of ultrashort pulses varied with the point of selection of a pulse in a train. The results were explained allowing for the simultaneous influence of burning of spectral holes in the population inversion and phase self-modulation on the operation of a laser with passive mode locking.

  2. Ag and Au nanoparticles for SERS substrates produced by pulsed laser ablation

    Energy Technology Data Exchange (ETDEWEB)

    Agarwal, N.R.; Castiglioni, C.; Lucotti, A. [DCMIC, Politecnico di Milano, Milano (Italy); Fazio, E.; Neri, F. [Dip. Fisica della Materia e Ingegneria Elettronica, Universita di Messina, Messina (Italy); Trusso, S. [CNR- Istituto per i Processi Chimico-Fisici, Messina (Italy); Santo, N. [Centro Interdipartimentale Microscopia Avanzata, Universita degli Studi di Milano, Milano (Italy); Ossi, P.M. [Dip. Energia, Politecnico di Milano, Milano (Italy)

    2011-08-15

    A method for the growth of films consisting of Nanoparticles (NP) of Ag and Au is presented. Nanostructured films were obtained by means of nanosecond pulsed laser ablation of a metallic target in presence of a controlled Ar atmosphere. The morphology of these films from island structures to isolated nanoparticles, measured by SEM, depends on the varying gas pressure (10-100 Pa) and on the number of laser pulses (500-30000), keeping other deposition parameters such as the target to substrate distance, incidence angle, laser wavelength, laser fluence constant. Fast imaging of the plasma, performed using a intensified and gateable CCD camera at different time delays with respect to the arrival of the laser pulse, allows revelation of the propagation regime of the ablation plume and inference of plasma initial velocity. This data along with the measured average ablated mass per pulse were taken as inputs to a model to estimate the average size of NPs grown in the expanding plume. The theoretical NP sizes were compared with sizes measured from TEM images. These images indicate narrow gradients of NP sizes. Hence strict control of growth parameters aids fine tuning of NP size that is essential for many applications, including Surface Enhanced Raman Spectroscopy (SERS) active substrates. UV-Visible Spectroscopy helped in determination of appropriate laser wavelength for resonant excitation of the localized surface plasmon. SERS Spectra obtained with increasingly lower concentrations of reference dye Rhodamin 6G (Rh6G) and medical drug Apomorphine, are discussed as a perspective of application to biomedical sensors. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  3. Submicro foaming in biopolymers by UV pulsed laser irradiation

    Science.gov (United States)

    Oujja, Mohamed; Rebollar, Esther; Gaspard, Solenne; Abrusci, Concepción; Catalina, Fernando; Lazare, Sylvain; Castillejo, Marta

    2006-05-01

    Microstructuring of polymers and biopolymers is of application in medical technology and biotechnology. Using different fabrication techniques three-dimensionally shaped and micro structured constructs can be developed for drug release and tissue engineering. As an alternative method, laser microstructuring offers a series of advantages including high resolution capability, low heat deposition in the substrate and high level of flexibility. In this work we present evidence of laser microfoam formation in collagen and gelatine by nanosecond pulsed laser irradiation in the UV at 248 and 266 nm. Irradiation at 355 nm produces melting followed by resolidification of the substrate, whereas irradiation at 532 and 1064 nm induces the formation of craters of irregular contours. Single pulse irradiation of a collagen film with an homogenized KrF microbeam yields a 20 μm thick expanded layer, which displays the interesting features of a nanofibrous 3-dimensional network with open cells. In gelatine, irradiation at 248 and 266 nm produces similar morphological modifications. The effect of the structural properties of the substrate on the laser induced microfoam is studied by comparing gelatines differing in gel strength (Bloom values 225 and 75) and in crosslinking degree. While results are discussed on the basis of thermal and photomechanical mechanisms and of the role played by the water content of the substrates, it is thought that such structures could have a biomimic function in future 3D cell culture devices for research.

  4. Interaction of gold nanoparticles with nanosecond laser pulses: Nanoparticle heating

    Energy Technology Data Exchange (ETDEWEB)

    Nedyalkov, N.N., E-mail: nnn_1900@yahoo.com [Institute of Electronics, Bulgarian Academy of Sciences, Tzarigradsko shousse 72, Sofia 1784 (Bulgaria); Imamova, S.E.; Atanasov, P.A. [Institute of Electronics, Bulgarian Academy of Sciences, Tzarigradsko shousse 72, Sofia 1784 (Bulgaria); Toshkova, R.A.; Gardeva, E.G.; Yossifova, L.S.; Alexandrov, M.T. [Institute of Experimental Pathology and Parasitology, Bulgarian Academy of Sciences, G. Bonchev Street, bl. 25, Sofia 1113 (Bulgaria); Obara, M. [Department of Electronics and Electrical Engineering, Faculty of Science and Technology, Keio University, 3-14-1 Hiyoshi, Kohoku-ku, Yokohama 223-8522 (Japan)

    2011-04-01

    Theoretical and experimental results on the heating process of gold nanoparticles irradiated by nanosecond laser pulses are presented. The efficiency of particle heating is demonstrated by in-vitro photothermal therapy of human tumor cells. Gold nanoparticles with diameters of 40 and 100 nm are added as colloid in the cell culture and the samples are irradiated by nanosecond pulses at wavelength of 532 nm delivered by Nd:YAG laser system. The results indicate clear cytotoxic effect of application of nanoparticle as more efficient is the case of using particles with diameter of 100 nm. The theoretical analysis of the heating process of nanoparticle interacting with laser radiation is based on the Mie scattering theory, which is used for calculation of the particle absorption coefficient, and two-dimensional heat diffusion model, which describes the particle and the surrounding medium temperature evolution. Using this model the dependence of the achieved maximal temperature in the particles on the applied laser fluence and time evolution of the particle temperature is obtained.

  5. Copper bromide vapour laser with an output pulse duration of up to 320 ns

    Energy Technology Data Exchange (ETDEWEB)

    Gubarev, F A; Fedorov, K V; Evtushenko, G S [National Research Tomsk Polytechnic University, Tomsk (Russian Federation); Fedorov, V F; Shiyanov, D V [V.E. Zuev Institute of Atmospheric Optics, Siberian Branch, Russian Academy of Sciences, Tomsk (Russian Federation)

    2016-01-31

    We report the development of a copper bromide vapour laser with an output pulse duration of up to 320 ns. To lengthen the pulse, the discharge current was limited using a compound switch comprising a pulsed hydrogen thyratron and a tacitron. This technique permits limiting the excitation of the working levels at the initial stage of the discharge development to lengthen the inversion lifetime. The longest duration of a laser pulse was reached in tubes 25 and 50 mm in diameter for a pulse repetition rate of 2 – 4 kHz. (lasers and laser beams)

  6. Molecular spinning by a chiral train of short laser pulses

    Science.gov (United States)

    Floß, Johannes; Averbukh, Ilya Sh.

    2012-12-01

    We provide a detailed theoretical analysis of molecular rotational excitation by a chiral pulse train, a sequence of linearly polarized pulses with the polarization direction rotating from pulse to pulse by a controllable angle. Molecular rotation with a preferential rotational sense (clockwise or counterclockwise) can be excited by this scheme. We show that the directionality of the rotation is caused by quantum interference of different excitation pathways. The chiral pulse train is capable of selective excitation of molecular isotopologs and nuclear spin isomers in a mixture. We demonstrate this using 14N2 and 15N2 as examples for isotopologs and para- and ortho-nitrogen as examples for nuclear-spin isomers.

  7. Femtosecond laser pulse induced desorption: A molecular dynamics simulation

    Energy Technology Data Exchange (ETDEWEB)

    Lončarić, Ivor, E-mail: ivor.loncaric@gmail.com [Centro de Física de Materiales CFM/MPC (CSIC-UPV/EHU), P. Manuel de Lardizabal 5, 20018 San Sebastián (Spain); Alducin, Maite [Centro de Física de Materiales CFM/MPC (CSIC-UPV/EHU), P. Manuel de Lardizabal 5, 20018 San Sebastián (Spain); Donostia International Physics Center DIPC, P. Manuel de Lardizabal 4, 20018 San Sebastián (Spain); Saalfrank, Peter [Institut für Chemie, Universität Potsdam, Karl-Liebknecht-Strasse 24-25, D-14476 Potsdam (Germany); Donostia International Physics Center DIPC, P. Manuel de Lardizabal 4, 20018 San Sebastián (Spain); Juaristi, J. Iñaki [Departamento de Física de Materiales, Facultad de Químicas, Universidad del País Vasco (UPV/EHU), Apartado 1072, 20080 San Sebastián (Spain); Centro de Física de Materiales CFM/MPC (CSIC-UPV/EHU), P. Manuel de Lardizabal 5, 20018 San Sebastián (Spain); Donostia International Physics Center DIPC, P. Manuel de Lardizabal 4, 20018 San Sebastián (Spain)

    2016-09-01

    In recent simulations of femtosecond laser induced desorption of molecular oxygen from the Ag(110) surface, it has been shown that depending on the properties (depth and electronic environment) of the well in which O{sub 2} is adsorbed, the desorption can be either induced dominantly by hot electrons or via excitations of phonons. In this work we explore whether the ratios between the desorption yields from different adsorption wells can be tuned by changing initial surface temperature and laser pulse properties. We show that the initial surface temperature is an important parameter, and that by using low initial surface temperatures the electronically mediated process can be favored. In contrast, laser properties seem to have only a modest influence on the results.

  8. Drug delivery with microsecond laser pulses into gelatin

    Science.gov (United States)

    Shangguan, Hanqun; Casperson, Lee W.; Shearin, Alan; Gregory, Kenton W.; Prahl, Scott A.

    1996-07-01

    Photoacoustic drug delivery is a technique for localized drug delivery by laser-induced hydrodynamic pressure following cavitation bubble expansion and collapse. Photoacoustic drug delivery was investigated on gelatin-based thrombus models with planar and cylindrical geometries by use of one microsecond laser pulses. Solutions of a hydrophobic dye in mineral oil permitted monitoring of delivered colored oil into clear gelatin-based thrombus models. Cavitation bubble development and photoacoustic drug delivery were visualized with flash photography. This study demonstrated that cavitation is the governing mechanism for photoacoustic drug delivery, and the deepest penetration of colored oil in gels followed the bubble collapse. Spatial distribution measurements revealed that colored oil could be driven a few millimeters into the gels in both axial and radial directions, and the penetration was less than 500 mu m when the gelatin structure was not fractured. localized drug delivery, cavitation bubble, laser thrombolysis.

  9. Testing of a femtosecond pulse laser in outer space

    Science.gov (United States)

    Lee, Joohyung; Lee, Keunwoo; Jang, Yoon-Soo; Jang, Heesuk; Han, Seongheum; Lee, Sang-Hyun; Kang, Kyung-In; Lim, Chul-Woo; Kim, Young-Jin; Kim, Seung-Woo

    2014-01-01

    We report a test operation of an Er-doped fibre femtosecond laser which was conducted for the first time in outer space. The fibre-based ultrashort pulse laser payload was designed to meet space-use requirements, undergone through ground qualification tests and finally launched into a low-earth orbit early in 2013. Test results obtained during a one-year mission lifetime confirmed stable mode-locking all the way through although the radiation induced attenuation (RIA) in the Er-doped gain fibre caused an 8.6% reduction in the output power. This successful test operation would help facilitate diverse scientific and technological applications of femtosecond lasers in space and earth atmosphere in the near future. PMID:24875665

  10. Testing of a femtosecond pulse laser in outer space.

    Science.gov (United States)

    Lee, Joohyung; Lee, Keunwoo; Jang, Yoon-Soo; Jang, Heesuk; Han, Seongheum; Lee, Sang-Hyun; Kang, Kyung-In; Lim, Chul-Woo; Kim, Young-Jin; Kim, Seung-Woo

    2014-05-30

    We report a test operation of an Er-doped fibre femtosecond laser which was conducted for the first time in outer space. The fibre-based ultrashort pulse laser payload was designed to meet space-use requirements, undergone through ground qualification tests and finally launched into a low-earth orbit early in 2013. Test results obtained during a one-year mission lifetime confirmed stable mode-locking all the way through although the radiation induced attenuation (RIA) in the Er-doped gain fibre caused an 8.6% reduction in the output power. This successful test operation would help facilitate diverse scientific and technological applications of femtosecond lasers in space and earth atmosphere in the near future.

  11. Electrical Addressing and Temporal Tweezing of Localized Pulses in Passively Mode-Locked Semiconductor Lasers

    CERN Document Server

    Camelin, P; Marconi, M; Giudici, M

    2016-01-01

    We show that the pumping current is a convenient parameter for manipulating the temporal Localized Structures (LSs), also called localized pulses, found in passively mode-locked Vertical-Cavity Surface-Emitting Lasers. While short electrical pulses can be used for writing and erasing individual LSs, we demonstrate that a current modulation introduces a temporally evolving parameter landscape allowing to control the position and the dynamics of LSs. We show that the localized pulses drifting speed in this landscape depends almost exclusively on the local parameter value instead of depending on the landscape gradient, as shown in quasi-instantaneous media. This experimental observation is theoretically explained by the causal response time of the semiconductor carriers that occurs on an finite timescale and breaks the parity invariance along the cavity, thus leading to a new paradigm for temporal tweezing of localized pulses. Different modulation waveforms are applied for describing exhaustively this paradigm. ...

  12. Microstructuring of soft organic matter by temporally shaped femtosecond laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Rebollar, Esther, E-mail: e.rebollar@iqfr.csic.es [Instituto de Química Física Rocasolano, IQFR-CSIC, Serrano 119, 28006 Madrid (Spain); Mildner, Jutta; Götte, Nadine; Otto, Dirk; Sarpe, Cristian; Köhler, Jens; Wollenhaupt, Matthias; Baumert, Thomas [Institut für Physik, Universität Kassel, Heinrich-Plett-Str. 40, D-34132 Kassel (Germany); Castillejo, Marta [Instituto de Química Física Rocasolano, IQFR-CSIC, Serrano 119, 28006 Madrid (Spain)

    2014-05-01

    Thin films of the biopolymers gelatine and chitosan were treated using femtosecond pulse shaping techniques combined with a microscope-based setup for material processing. The polymer films were irradiated with laser pulses of 35 fs and a central wavelength of 790 nm provided by an amplified Ti:Sapphire system. The effect of temporal pulse shaping, with quadratic and cubic spectral phases, on the induced morphology was analyzed by characterization of the created surface structures via scanning electron microscopy. We observed different material modification thresholds and different structure sizes for temporally asymmetric pulse shapes. The results indicate the possibility of control of the generated microstructures and are discussed in relation to the formation of free electrons and the different contributions of multi-photon and avalanche ionization processes.

  13. Pulse-periodic iodine photodissociation laser pumped with radiation from magnetoplasma compressors

    Science.gov (United States)

    Kashnikov, G. N.; Orlov, V. K.; Panin, A. N.; Piskunov, A. K.; Reznikov, V. A.

    1980-09-01

    The design and operation of an iodine photodissociation laser, pumped by radiation from magnetoplasma compressors, are described. The laser uses a closed-circulation system with C3F7I as the working gas. Repetitive-pulse operation has been achieved with an interval between pulses of 1 minute, a lasing energy of 110 J, and a pulse duration of 30 microseconds.

  14. Influence of laser pulse duration on extreme ultraviolet and ion emission features from tin plasmas

    Science.gov (United States)

    Roy, A.; Harilal, S. S.; Polek, M. P.; Hassan, S. M.; Endo, A.; Hassanein, A.

    2014-03-01

    We investigated the role of laser pulse duration and intensity on extreme ultraviolet (EUV) generation and ion emission from a laser produced Sn plasma. For producing plasmas, planar slabs of pure Sn were irradiated with 1064 nm Nd:YAG laser pulses with varying pulse duration (5-20 ns) and intensity. Experimental results performed at CMUXE indicate that the conversion efficiency (CE) of the EUV radiation strongly depend on laser pulse width and intensity, with a maximum CE of ˜2.0% measured for the shortest laser pulse width used (5 ns). Faraday Cup ion analysis of Sn plasma showed that the ion flux kinetic profiles are shifted to higher energy side with the reduction in laser pulse duration and narrower ion kinetic profiles are obtained for the longest pulse width used. However, our initial results showed that at a constant laser energy, the ion flux is more or less constant regardless of the excitation laser pulse width. The enhanced EUV emission obtained at shortest laser pulse duration studied is related to efficient laser-plasma reheating supported by presence of higher energy ions at these pulse durations.

  15. Influence of laser pulse duration on extreme ultraviolet and ion emission features from tin plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Roy, A., E-mail: roy@fzu.cz, E-mail: aroy@barc.gov.in [HiLASE Project, Department of Diode-Pumped Lasers, Institute of Physics of the ASCR, Na Slovance 2, 18221 Prague (Czech Republic); School of Nuclear Engineering and Center for Materials Under Extreme Environment (CMUXE), Purdue University, West Lafayette, Indiana 47907 (United States); Harilal, S. S.; Polek, M. P.; Hassan, S. M.; Hassanein, A. [School of Nuclear Engineering and Center for Materials Under Extreme Environment (CMUXE), Purdue University, West Lafayette, Indiana 47907 (United States); Endo, A. [HiLASE Project, Department of Diode-Pumped Lasers, Institute of Physics of the ASCR, Na Slovance 2, 18221 Prague (Czech Republic)

    2014-03-15

    We investigated the role of laser pulse duration and intensity on extreme ultraviolet (EUV) generation and ion emission from a laser produced Sn plasma. For producing plasmas, planar slabs of pure Sn were irradiated with 1064 nm Nd:YAG laser pulses with varying pulse duration (5–20 ns) and intensity. Experimental results performed at CMUXE indicate that the conversion efficiency (CE) of the EUV radiation strongly depend on laser pulse width and intensity, with a maximum CE of ∼2.0% measured for the shortest laser pulse width used (5 ns). Faraday Cup ion analysis of Sn plasma showed that the ion flux kinetic profiles are shifted to higher energy side with the reduction in laser pulse duration and narrower ion kinetic profiles are obtained for the longest pulse width used. However, our initial results showed that at a constant laser energy, the ion flux is more or less constant regardless of the excitation laser pulse width. The enhanced EUV emission obtained at shortest laser pulse duration studied is related to efficient laser-plasma reheating supported by presence of higher energy ions at these pulse durations.

  16. Reshaping, Fragmentation, and Assembly of Gold Nanoparticles Assisted by Pulse Lasers.

    Science.gov (United States)

    González-Rubio, Guillermo; Guerrero-Martínez, Andrés; Liz-Marzán, Luis M

    2016-04-19

    controlled welding of plasmonic gold nanostructures by electromagnetic field enhancement at the hot spots of assembled Au NPs. The combination of such nanostructures with pulse lasers promises significant chemical and biochemical advances, including the structural determination of organic reaction intermediates, the investigation of phase transitions in inorganic nanomaterials at mild reaction conditions, or the efficient photothermal destruction of cancer cells avoiding damage of surrounding tissue.

  17. COMPARATIVE EVALUATION OF LONG PULSE ALEXANDRITE LASER AND INTENSE PULSED LIGHT SYSTEMS FOR PSEUDOFOLLICULITIS BARBAE TREATMENT WITH ONE YEAR OF FOLLOW UP

    OpenAIRE

    Leheta Tahra

    2009-01-01

    Background: Existing remedies for controlling pseudofolliculitis barbae (PFB) are sometimes helpful; however the positive effects are often short lived. The only definitive cure for PFB is permanent removal of the hair follicle. Aims: Our aim was to compare the efficacy of the Alexandrite laser with the intense pulsed light system in the treatment of PFB and to follow up the recurrence. Methods: Twenty male patients seeking laser hair removal for the treatment of PFB were enrolled in thi...

  18. Magnus expansion for laser-matter interaction: Application to generic few-cycle laser pulses

    DEFF Research Database (Denmark)

    Klaiber, Michael; Dimitrovski, Darko; Briggs, John S.

    2009-01-01

    We treat the interaction of an atom with a short intense few-cycle laser pulse by the use of the Magnus expansion of the time-evolution operator. Terms of the Magnus expansion up to the third order in the pulse duration are evaluated explicitly, and expressions for the transition probability...... of the Magnus approximation are in excellent agreement with time-dependent transition probabilities obtained from accurate ab initio numerical calculations. However, the limitation of the Magnus expansion for pulses having both vanishing momentum and position shifts is demonstrated also....

  19. Duration of an intense laser pulse can determine the breakage of multiple chemical bonds.

    Science.gov (United States)

    Xie, Xinhua; Lötstedt, Erik; Roither, Stefan; Schöffler, Markus; Kartashov, Daniil; Midorikawa, Katsumi; Baltuška, Andrius; Yamanouchi, Kaoru; Kitzler, Markus

    2015-08-14

    Control over the breakage of a certain chemical bond in a molecule by an ultrashort laser pulse has been considered for decades. With the availability of intense non-resonant laser fields it became possible to pre-determine femtosecond to picosecond molecular bond breakage dynamics by controlled distortions of the electronic molecular system on sub-femtosecond time scales using field-sensitive processes such as strong-field ionization or excitation. So far, all successful demonstrations in this area considered only fragmentation reactions, where only one bond is broken and the molecule is split into merely two moieties. Here, using ethylene (C2H4) as an example, we experimentally investigate whether complex fragmentation reactions that involve the breakage of more than one chemical bond can be influenced by parameters of an ultrashort intense laser pulse. We show that the dynamics of removing three electrons by strong-field ionization determines the ratio of fragmentation of the molecular trication into two respectively three moieties. We observe a relative increase of two-body fragmentations with the laser pulse duration by almost an order of magnitude. Supported by quantum chemical simulations we explain our experimental results by the interplay between the dynamics of electron removal and nuclear motion.

  20. High-power pulsed and CW diode-pumped mode-locked Nd:YAG lasers

    Science.gov (United States)

    Marshall, Larry R.; Hays, A. D.; Kaz, Alex; Kasinski, Jeff; Burnham, R. L.

    1991-01-01

    The operation of both pulsed and CW diode-pumped mode-locked Nd:YAG lasers are presented. The pulsed laser produced 1.0 mJ with pulsewidths of 90 psec at 20 Hz. The CW pumped laser produced 6 W output at 1.064 microns and 3 W output at 532 nm.

  1. Effect of surface-breakdown plasma on metal drilling by pulsed CO2-laser radiation

    Science.gov (United States)

    Arutiunian, P. V.; Baranov, V. Iu.; Bobkov, I. V.; Bol'Shakov, L. A.; Dolgov, V. A.

    1988-03-01

    The effect of low-threshold surface breakdown produced by short (5-microsec) CO2-laser pulses on the metal drilling process is investigated. Data on the interaction of metals with laser pulses having the same duration but different shape are shown to be different. The effect of the ambient atmospheric pressure on the laser drilling process is investigated.

  2. Novel oral applications of ultra-short laser pulses

    Science.gov (United States)

    Wieger, V.; Wernisch, J.; Wintner, E.

    2007-02-01

    In the past decades, many efforts have been made to replace mechanical tools in oral applications by various laser systems. The reasons therefore are manifold: i) Friction causes high temperatures damaging adjacent tissue. ii) Smear layers and rough surfaces are produced. iii) Size and shape of traditional tools are often unsuitable for geometrically complicated incisions and for minimum invasive treatment. iv) Mechanical damage of the remaining tissue occurs. v) Online diagnosis for feedback is not available. Different laser systems in the µs and sub-&mrgs-pulse regime, among them Erbium lasers, have been tested in the hope to overcome the mentioned drawbacks and, to some extent, they represent the current state of the art with respect to commercial and hence practical application. In the present work the applicability of scanned ultrashort pulse lasers (USPLs) for biological hard tissue as well as dental restoration material removal was tested. It is shown that cavities with features superior to mechanically treated or Erbium laser ablated cavities can be generated if appropriate scan algorithms and optimum laser parameters are matched. Smooth cavity rims, no microcracks, melting or carbonisation and precise geometry are the advantages of scanned USLP ablation. For bone treatment better healing conditions are expected as the natural structure remains unaffected by the preparation procedure. The novelty of this work is represented by a comprehensive compilation of various experimental results intended to assess the performance of USPLs. In this context, various pulse durations in the picosecond and femtosecond regime were applied to dental and bone tissue as well as dental restoration materials which is considered to be indispensable for a complete assessment. Parameters like ablation rates describing the efficiency of the ablation process, and ablation thresholds were determined - some of them for the first time - and compared to the corresponding Erbium

  3. Experimental study of laser-induced plasma: Influence of laser fluence and pulse duration

    Energy Technology Data Exchange (ETDEWEB)

    Bai, Xueshi; Ma, Qianli; Perrier, Maxime; Motto-Ros, Vincent [Institut Lumière Matière, UMR5306 Université Lyon 1-CNRS, Université de Lyon, 69622 Villeurbanne cedex (France); Sabourdy, David; Nguyen, Luc; Jalocha, Alain [CILAS Laser Company, Photonics Department, 45000 Orléans (France); Yu, Jin, E-mail: jin.yu@univ-lyon1.fr [Institut Lumière Matière, UMR5306 Université Lyon 1-CNRS, Université de Lyon, 69622 Villeurbanne cedex (France)

    2013-09-01

    Influence of laser fluence and pulse duration on the morphology and the internal structure of plasma induced by infrared nanosecond laser pulse on an aluminum target placed in an argon ambient gas of one atmosphere pressure was experimentally studied. Dual-wavelength differential spectroscopic imaging was used in the experiment, which allowed observing the detailed structure inside of the ablation plume with distributions of species evaporated from the target as well as contributed by the ambient gas. Different regimes of post-ablation interaction were investigated using different laser fluences and pulse durations. We demonstrate in particular that plasma shielding due to various species localized in different zones inside of the plume leads to different morphologies and internal structures of the plasma. At moderate fluence, the plasma shielding due to the ablation vapor localized in the central part of the plume leads to its nearly spherical expansion with a layered structure of the distribution of different species. At higher fluence, the plasma shielding becomes strongly contributed by ionized ambient gas localized in the propagation front of the plume. An elongated morphology of the plume is observed with a zone of mixing between different species evaporated from the target or contributed by the ambient gas. Finally with extremely strong plasma shielding by ionized ambient gas in the case of a long duration pulse at high fluence, a delayed evaporation from the target is observed due to the ejection of melted material by splashing. - Highlights: • Morphology and internal structure of a plasma were experimentally determined. • Laser fluence and pulse duration are critical parameters for plasma structure. • Plasma shielding due to various species leads to different plasma structures. • Different regimes of laser-support absorption wave are used for interpretation. • Splashing ejection is observed for strong plasma shielding with long pulse.

  4. Synthesis of silver nanoparticles by laser ablation in ethanol: A pulsed photoacoustic study

    Energy Technology Data Exchange (ETDEWEB)

    Valverde-Alva, M.A., E-mail: azbmiguel@gmail.com [Posgrado en Ciencia e Ingeniería de Materiales, Universidad Nacional Autónoma de México (UNAM), México D.F., C.P. 04510, México (Mexico); García-Fernández, T. [Universidad Autónoma de la Ciudad de México (UACM), Prolongación San Isidro 151, Col. San Lorenzo Tezonco, México D.F., C.P. 09790, México (Mexico); Villagrán-Muniz, M.; Sánchez-Aké, C.; Castañeda-Guzmán, R. [CCADET Universidad Nacional Autónoma de México (UNAM), México D.F., C.P. 04510, México (Mexico); Esparza-Alegría, E. [Facultad de Ciencias, Universidad Nacional Autónoma de México (UNAM), México D.F., C.P. 04510, México (Mexico); Sánchez-Valdés, C.F. [Instituto Potosino de Investigación Científica y Tecnológica A.C., Camino a la Presa San José 2055, Col. Lomas 4a sección, San Luis Potosí, S.L.P., C.P. 78216, México (Mexico); and others

    2015-11-15

    Graphical abstract: - Highlights: • Pulsed photoacoustic technique allowed to determine the production rate of NPs. • Pulsed photoacoustic technique allows to determine the Ag concentration in colloids. • The nanoparticles production rate drops quickly during the first laser pulses. • Nanoparticles production rate is almost constant after few hundreds of laser shots. • Photoacoustic signal amplitude was proportional to fluence on the target surface. - Abstract: The pulsed photoacoustic (PA) technique was used to study the synthesis by laser ablation of silver nanoparticles (Ag-NPs) in ethanol. PA technique allowed to determine the production rate per laser pulse and concentration of synthesized Ag-NPs. The samples were produced by using a pulsed Nd:YAG laser with 1064 nm of wavelength and 7 ns of pulse duration. The laser pulse energy varied from 10 to 100 mJ. Transmission electron microscopy micrographs demonstrated that the obtained nanoparticles were spherical with an average size close to 10 nm. The absorption spectra of the colloids showed a plasmon absorption peak around 400 nm. The PA analyses showed a significant reduction of the production rate of Ag-NPs during the first hundreds of laser pulses. For a higher number of pulses this rate was kept almost constant. Finally, we found that the root mean square (RMS) value of the PA signal was proportional to the laser pulse fluence on the target surface. Thus PA technique was useful to monitor the ablation process.

  5. Effects of pulsed Nd:YAG laser irradiation on root canal wall dentin with different laser initiators.

    Science.gov (United States)

    Zhang, C; Kimura, Y; Matsumoto, K; Harashima, T; Zhou, H

    1998-05-01

    The effects of pulsed Nd:YAG laser irradiation with different laser initiators on the permeability and ultrastructure of the root canal wall dentin were investigated in vitro. Forty extracted human single-rooted teeth were randomly assigned to four groups. Group 1 teeth were not lased as a control. Group 2 specimens received four 10-s duration laser exposures for a total exposure of 40 s/canal. In group 3 specimens, the root canals were painted with black ink and then lased by the same method as group 2 teeth. In group 4 specimens, root canals were treated with 38% Ag(NH3)2F and then lased by the same method as group 2 teeth. Laser parameters were set at 2 W, 20 pps. After being placed in 0.6% rhodamine B solution for 48 h, the teeth were sectioned for study by stereoscope and scanning electron microscopy. Statistical analysis showed there were significant differences (p permeability in the apical areas between groups 3 and 1, 4 and 1, and 4 and 2. Scanning electron microscopic examination showed that laser treatment alone had no obvious effects on the root canal wall. The root canal surfaces prepared for by laser irradiation with black ink or 38% Ag(NH3)2F revealed melting, smear layer evaporation, and open dentinal tubules. Black ink was more effective than 38% Ag(NH3)2F as a Nd:YAG laser initiator.

  6. Fatigue Testing of Materials by UV Pulsed Laser Irradiation

    CERN Document Server

    Calatroni, S; Taborelli, M

    2004-01-01

    The energy dissipated by the RF currents in the cavities of pulsed high-power linacs induces cycles of the surface temperature. In the case of the CLIC main linac the expected amplitude of the thermal cycles is above fifty degrees, for a total number of pulses reaching 1011. The differential thermal expansion due to the temperature gradient in the material creates a cyclic stress that can result in surface break-up by fatigue. The materials for cavity fabrication must therefore be selected in order to withstand such constraints whilst maintaining an acceptable surface state. The fatigue behaviour of Cu and CuZr alloy has been tested by inducing larger surface peak temperatures, thus reducing the number of cycles to failure, irradiating the surface with 40 ns pulses of UV light (308 nm) from an excimer laser. Surface break-up is observed after different number of laser shots as a function of the peak temperature. CuZr appears to withstand a much larger number of cycles than Cu, for equal peak temperature. The ...

  7. Delivery of molecules into cells using carbon nanoparticles activated by femtosecond laser pulses.

    Science.gov (United States)

    Chakravarty, Prerona; Qian, Wei; El-Sayed, Mostafa A; Prausnitz, Mark R

    2010-08-01

    A major barrier to drug and gene delivery is crossing the cell's plasma membrane. Physical forces applied to cells via electroporation, ultrasound and laser irradiation generate nanoscale holes in the plasma membrane for direct delivery of drugs into the cytoplasm. Inspired by previous work showing that laser excitation of carbon nanoparticles can drive the carbon-steam reaction to generate highly controlled shock waves, we show that carbon black nanoparticles activated by femtosecond laser pulses can facilitate the delivery of small molecules, proteins and DNA into two types of cells. Our initial results suggest that interaction between the laser energy and carbon black nanoparticles may generate photoacoustic forces by chemical reaction to create transient holes in the membrane for intracellular delivery.

  8. Thin film surface processing by ultrashort laser pulses (USLP)

    Science.gov (United States)

    Scorticati, D.; Skolski, J. Z. P.; Römer, G. R. B. E.; Huis in't Veld, A. J.; Workum, M.; Theelen, M.; Zeman, M.

    2012-06-01

    In this work, we studied the feasibility of surface texturing of thin molybdenum layers on a borosilicate glass substrate with Ultra-Short Laser Pulses (USLP). Large areas of regular diffraction gratings were produced consisting of Laserinduced periodic surface structures (LIPSS). A short pulsed laser source (230 fs-10 ps) was applied using a focused Gaussian beam profile (15-30 μm). Laser parameters such as fluence, overlap (OL) and Overscans (OS), repetition frequency (100-200 kHz), wavelength (1030 nm, 515 nm and 343 nm) and polarization were varied to study the effect on periodicity, height and especially regularity of LIPSS obtained in layers of different thicknesses (150-400 nm). The aim was to produce these structures without cracking the metal layer and with as little ablation as possible. It was found that USLP are suitable to reach high power densities at the surface of the thin layers, avoiding mechanical stresses, cracking and delamination. A possible photovoltaic (PV) application could be found in texturing of thin film cells to enhance light trapping mechanisms.

  9. The effects of pulsed laser parameters on the photoacoustic detection of glucose aqueous solution

    Science.gov (United States)

    Ren, Zhong; Liu, Guodong; Huang, Zhen; Zeng, Lvming

    2017-10-01

    In this study, the photoacoustic detection system was established based on the Q switched Nd: YAG 532nm pumped optical parametric oscillator pulsed laser and the ultrasonic detector. Based on the established photoacoustic detection system, the effects of pulsed laser on the photoacoustic detection of glucose aqueous solutions were experimentally studied. The photoacoustic peak-to-peak values of glucose and pure water were obtained at different output energy of pulsed laser and at the wavelengths from 1300nm to 2200nm. Experimental results show that the photoacoustic peak-to-peak values of glucose linearly increase with the increasing of the output energy of pulsed laser. The photoacoustic peak-to-peak values were compensated because the output energy of pulsed laser exponentially decreased with the increasing of the wavelengths of pulsed laser. The characteristic wavelengths of glucose were determined according to the difference spectral between the compensated photoacoustic peak-to-peak values of glucose aqueous solution and pure water.

  10. Femtosecond laser ablation of silver foil with single and double pulses

    CSIR Research Space (South Africa)

    Roberts, DE

    2009-01-01

    Full Text Available The average ablation depth per pulse of silver foil by 130 fs laser pulses has been measured in vacuum over a range of three orders of magnitude of pulse fluence up to 900 J cm_2. In addition, double pulses with separations up to 3.4 ns have been...

  11. Femtosecond laser ablation of silver foil with single and double pulses

    CSIR Research Space (South Africa)

    Roberts, DE

    2009-01-01

    Full Text Available The average ablation depth per pulse of silver foil by 130 fs laser pulses has been measured in vacuum over a range of three orders of magnitude of pulse fluence up to 900 J cm-2. In addition, double pulses with separations up to 3.4 ns have been...

  12. Simulated electronic heterodyne recording and processing of pulsed-laser holograms

    Science.gov (United States)

    Decker, A. J.

    1979-01-01

    The electronic recording of pulsed-laser holograms is proposed. The polarization sensitivity of each resolution element of the detector is controlled independently to add an arbitrary phase to the image waves. This method which can be used to simulate heterodyne recording and to process three-dimensional optical images, is based on a similar method for heterodyne recording and processing of continuous-wave holograms.

  13. Pulsed-laser-induced nanoscale island formation in thin metal-on-oxide films

    OpenAIRE

    Henley, SJ; Carey, JD; Silva, SRP

    2005-01-01

    he mechanisms controlling the nanostructuring of thin metal-on-oxide films by nanosecond pulsed excimer lasers are investigated. When permitted by the interfacial energetics, the breakup of the metal film into nanoscale islands is observed. A range of metals (Au, Ag, Mo, Ni, Ti, and Zn) with differing physical and thermodynamic properties, and differing tendencies for oxide formation, are investigated. The nature of the interfacial metal-substrate interaction, the thermal conductivity of the ...

  14. Investigations on fibers for high-peak power pulsed Nd:YAG-lasers for laser detonator

    Science.gov (United States)

    Gao, Yang; Zhao, Xing-hai; Su, Wei; Cheng, Yong-sheng; Xu, Mei-jian; Duan, Wen-tao; Yu, Hai-wu

    2008-04-01

    For laser detonator application, high-peak power pulsed Nd:YAG laser is transmitted through all-silica optical fiber. The transmission properties of step-index fibers are investigated, using a high-peak power pulsed Nd: YAG rod laser with beyond 1MW power and Q-switch mode. The fibers are step-index multimode fibers with 400 or 600 μm core diameters, 440 or 660 μm cladding diameters. The power delivery characteristics were studied by theory and experiments. The results show that the fiber core diameter, NA, length and so on affect the transmission efficiency for high power laser. When the laser power is beyond a certain threshold, the SRS and SBS will be serious; the quantity of fiber end-face limits to the raising of laser power passing through fibers; the zero-probability damage threshold is calculated according to ISO/DIS standard 11254-1.2, which is 58.6J/cm2. Energy distribution of output beam from fibers will be uniform. Even the fiber end-face was partly damaged, laser power is still deliverable, and the transmission efficiency is related to the fiber damage grade.

  15. Effects of pulse width and repetition rate of pulsed laser on kinetics and production of singlet oxygen luminescence

    Directory of Open Access Journals (Sweden)

    Defu Chen

    2016-11-01

    Full Text Available Pulsed and continuous-wave (CW lasers have been widely used as the light sources for photodynamic therapy (PDT treatment. Singlet oxygen (1O2 is known to be a major cytotoxic agent in type-II PDT and can be directly detected by its near-infrared luminescence at 1270nm. As compared to CW laser excitation, the effects of pulse width and repetition rate of pulsed laser on the kinetics and production of 1O2 luminescence were quantitatively studied during photosensitization of Rose Bengal. Significant difference in kinetics of 1O2 luminescence was found under the excitation with various pulse widths of nanosecond, microsecond and CW irradiation with power of 20mW. The peak intensity and duration of 1O2 production varied with the pulse widths for pulsed laser excitation, while the 1O2 was generated continuously and its production reached a steady state with CW excitation. However, no significant difference (P>0.05 in integral 1O2 production was observed. The results suggest that the PDT efficacy using pulsed laser may be identical to the CW laser with the same wavelength and the same average fluence rate below a threshold in solution.

  16. Experimental set-up for a pulsed CO2 laser rangefinder with heterodyne detection

    Science.gov (United States)

    Bloem, J.

    1990-08-01

    The creation of a pulsed CO2 laser range finder with heterodyne detection is described. The range finder uses a hybrid CW-TEA (Continuous Wave-Transversely Excited Atmospheric pressure) laser as emitter and an RF laser as local oscillator. The laser stabilization is described. The frequency offset between the transmitted laser pulse and the local oscillator laser is locked at 20 MHz. The long term (20 to 30 min) variation of this offset frequency is limited to 50 kHz. The effects of pulsing on this stabilization were eliminated. The signal processing was started. A rough model of the laser pulse and its frequency characteristics was developed. An AM demodulator was developed to determine the envelope of the reflected pulses. The system created can be used to measure the range to (and in the future also the speed of) diffuse reflecting targets.

  17. Short energetic electron bunches from laser wakefield accelerator with orthogonally polarized perpendicularly crossed laser pulses

    Science.gov (United States)

    Horný, Vojtěch; Petržílka, Václav; Klimo, Ondřej; Krůs, Miroslav

    2017-05-01

    Electron acceleration with optical injection by a perpendicularly propagating and orthogonally polarized low intensity laser pulse into a nonlinear plasma wave driven by a short intense laser pulse was explored by particle- in-cell simulations. The scheme presented here provides an energetic electron bunch in the first ion cavity with a low energy spread. The electron bunch short and compact, with the mean energy about 400 MeV and a low energy spread about 10 MeV in time of 6 ps of acceleration. The injected charge is several tens of pC for the low intensity of the injection pulse. Initial positions of electrons forming the energetic bunch are shown and then these electrons are followed during the simulation in order to understand the injection process and determine electron bunch properties.

  18. No effect of femtosecond laser pulses on M13, E. coli, DNA, or protein

    Science.gov (United States)

    Wigle, Jeffrey C.; Holwitt, Eric A.; Estlack, Larry E.; Noojin, Gary D.; Saunders, Katharine E.; Yakovlev, Valdislav V.; Rockwell, Benjamin A.

    2014-01-01

    Data showing what appears to be nonthermal inactivation of M13 bacteriophage (M13), Tobacco mosaic virus, Escherichia coli (E. coli), and Jurkatt T-cells following exposure to 80-fs pulses of laser radiation have been published. Interest in the mechanism led to attempts to reproduce the results for M13 and E. coli. Bacteriophage plaque-forming and bacteria colony-forming assays showed no inactivation of the microorganisms; therefore, model systems were used to see what, if any, damage might be occurring to biologically important molecules. Purified plasmid DNA (pUC19) and bovine serum albumin were exposed to and analyzed by agarose gel electrophoresis (AGE) and polyacrylamide gel electrophoresis (PAGE), respectively, and no effect was found. DNA and coat proteins extracted from laser-exposed M13 and analyzed by AGE or PAGE found no effect. Raman scattering by M13 in phosphate buffered saline was measured to determine if there was any physical interaction between M13 and femtosecond laser pulses, and none was found. Positive controls for the endpoints measured produced the expected results with the relevant assays. Using the published methods, we were unable to reproduce the inactivation results or to show any interaction between ultrashort laser pulses and buffer/water, DNA, protein, M13 bacteriophage, or E. coli.

  19. Design principles for high quality electron beams via colliding pulses in laser plasma accelerators

    Directory of Open Access Journals (Sweden)

    E. Cormier-Michel

    2014-09-01

    Full Text Available Laser plasma based accelerators have the potential to reduce dramatically the size and cost of future particle colliders and light sources. Production of high quality beams along with reproducibility, tunability, and efficiency are required for many applications. We present design principles for two-pulse colliding laser pulse injection mechanisms, which can meet these requirements. Simulations are used to determine the best conditions for the production of high quality beams: high charge, low energy spread, and low emittance. Simulations also allow access to the internal dynamics of the interaction, providing insight regarding further improvement of the beam quality. We find that a 20 pC beam can be accelerated to 300 MeV in 4 mm with only a few percent energy spread and transverse normalized emittance close to 1 mm mrad, using a 10 TW laser. We demonstrate that this design scales according to linear theory. Control of the laser pulse mode content and subsequent evolution in the plasma channel are shown to be critical for achieving the highest beam quality.

  20. Nanoalloy Printed and Pulse-Laser Sintered Flexible Sensor Devices with Enhanced Stability and Materials Compatibility

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Wei; Rovore, Thomas; Weerawarne, Darshana; Osterhoudt, Gavin; Kang, Ning; Joseph, Pharrah; Luo, Jin; Shim, Bonggu; Poliks, Mark; Zhong, Chuan-Jian

    2015-06-02

    While conformal and wearable devices have become one of the most desired formats for printable electronics, it is challenging to establish a scalable process that produces stable conductive patterns but also uses substrates compatible with widely available wearable materials. Here, we describe findings of an investigation of a nanoalloy ink printed and pulsed laser sintered conductive patterns as flexible functional devices with enhanced stability and materials compatibility. While nanoparticle inks are desired for printable electronics, almost all existing nanoparticle inks are based on single-metal component, which, as an electronic element, is limited by its inherent stabilities of the metal such as propensity of metal oxidation and mobility of metal ions, especially in sintering processes. The work here has demonstrated the first example in exploiting plasmonic coupling of nanoalloys and pulsed-laser energy with controllable thermal penetration. The experimental and theoretical results have revealed clear correlation between the pulsed laser parameters and the nanoalloy structural characteristics. The superior performance of the resulting flexible sensor device, upon imparting nanostructured sensing materials, for detecting volatile organic compounds has significant implications to developing stable and wearable sensors for monitoring environmental pollutants and breath biomarkers. This simple “nanoalloy printing 'laser sintering' nanostructure printing” process is entirely general to many different sensor devices and nanostructured sensing materials, enabling the ability to easily construct sophisticated sensor array.

  1. Ultrafast dynamics driven by intense light pulses from atoms to solids, from lasers to intense X-rays

    CERN Document Server

    Gräfe, Stefanie

    2016-01-01

    This book documents the recent vivid developments in the research field of ultrashort intense light pulses for probing and controlling ultrafast dynamics. The recent fascinating results in studying and controlling ultrafast dynamics in ever more complicated systems such as (bio-)molecules and structures of meso- to macroscopic sizes on ever shorter time-scales are presented. The book is written by some of the most eminent experimental and theoretical experts in the field. It covers the new groundbreaking research directions that were opened by the availability of new light sources such as fully controlled intense laser fields with durations down to a single oscillation cycle, short-wavelength laser-driven attosecond pulses and intense X-ray pulses from the upcoming free electron lasers. These light sources allowed the investigation of dynamics in atoms, molecules, clusters, on surfaces and very recently also in nanostructures and solids in new regimes of parameters which, in turn, led to the identification of...

  2. REVIEW ARTICLE: Spatio-temporal couplings in ultrashort laser pulses

    Science.gov (United States)

    Akturk, Selcuk; Gu, Xun; Bowlan, Pamela; Trebino, Rick

    2010-09-01

    The electric field of an ultrashort laser pulse often fails to separate into a product of purely temporal and purely spatial factors. These so-called spatio-temporal couplings constitute a broad range of physical effects, which often become important in applications. In this review, we compile some recent experimental and theoretical work on the understanding, avoidance and applications of these effects. We first present a discussion of the characteristics of pulses containing spatio-temporal couplings, including their sources, a mathematical description and the interdependence of different couplings. We then review different experimental methods for their characterization. Finally, we describe different applications of spatio-temporal couplings and suggest further schemes for their exploitation and avoidance.

  3. Short intense laser pulse collapse in near-critical plasma.

    Science.gov (United States)

    Sylla, F; Flacco, A; Kahaly, S; Veltcheva, M; Lifschitz, A; Malka, V; d'Humières, E; Andriyash, I; Tikhonchuk, V

    2013-02-22

    It is observed that the interaction of an intense ultrashort laser pulse with a near-critical gas jet results in the pulse collapse and the deposition of a significant fraction of the energy. This deposition happens in a small and well-localized volume in the rising part of the gas jet, where the electrons are efficiently accelerated and heated. A collisionless plasma expansion over ~ 150 μm at a subrelativistic velocity (~ c/3) has been optically monitored in time and space, and attributed to the quasistatic field ionization of the gas associated with the hot electron current. Numerical simulations in good agreement with the observations suggest the acceleration in the collapse region of relativistic electrons, along with the excitation of a sizable magnetic dipole that sustains the electron current over several picoseconds.

  4. Robust Short-Pulse, High-Peak-Power Laser Transmitter for Optical Communications

    Science.gov (United States)

    Wright, Malcolm W.

    2009-01-01

    We report on a pulsed fiber based master oscillator power amplifier laser at 1550 nm to support moderate data rates with high peak powers in a compact package suitable for interplanetary optical communications. To accommodate pulse position modulation, the polarization maintaining laser transmitter generates pulses from 0.1 to 1 ns with variable duty cycle over a pulse repetition frequency range of 10 to 100 MHz.

  5. A 158 fs 5.3 nJ fiber-laser system at 1 mu m using photonic bandgap fibers for dispersion control and pulse compression

    DEFF Research Database (Denmark)

    Nielsen, C.K.; Jespersen, Kim Giessmann; Keiding, S.R.

    2006-01-01

    We demonstrate a 158 fs 5.3 nJ mode-locked laser system based on a fiber oscillator, fiber amplifier and fiber compressor. Dispersion compensation in the fiber oscillator was obtained with a solid-core photonic bandgap (SC-PBG) fiber spliced to standard fibers, and external compression is obtained...

  6. Formation of hexagonal-wurtzite germanium by pulsed laser ablation

    Science.gov (United States)

    Zhang, Y.; Iqbal, Z.; Vijayalakshmi, S.; Qadri, S.; Grebel, H.

    2000-08-01

    A stable phase of relatively large hexagonal-wurtzite germanium (lonsdaleite) crystals (up to 10 μm) was formed when germanium was directly deposited at low pressure using pulsed ultraviolet laser ablation. Films were grown on various substrates at room temperature from a single crystal, cubic germanium target. Crystallites of the hexagonal-wurtzite phase of germanium were clearly identified using selected area electron diffraction. Further characterizations of the films were made using X-ray diffraction and confocal scanning micro-Raman spectroscopy.

  7. Frequency doubling of ultrashort laser pulses in biological tissues

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Beop-Min [Medical Technology Program, Lawrence Livermore National Laboratory, 7000 East Avenue L-399, Livermore, California 94550 (United States); Eichler, Juergen [Technische Fachhochschule Berlin, University of Applied Sciences, Seestrasse 63, 13347 Berlin, (Germany); Da Silva, Luiz B. [Medical Technology Program, Lawrence Livermore National Laboratory, 7000 East Avenue L-399, Livermore, California 94550 (United States)

    1999-12-01

    Theoretical and experimental studies of second-harmonic generation (SHG) in biological tissues was performed by use of ultrashort laser pulses (<1 ps). A simplified one-dimensional model for the generation and the propagation of frequency-doubled light inside tissue was developed. This model was tested in vitro against measurements of pig and chicken tissue and human tooth. The experimental results indicate that the intensity of SHG varies significantly among tissues types and between test sites in individual tissue. Possibilities of using this nonlinear tissue property in imaging and diagnostics are discussed. (c) 1999 Optical Society of America.

  8. Metallic Light Absorbers Produced by Femtosecond Laser Pulses

    Directory of Open Access Journals (Sweden)

    Anatoliy Y. Vorobyev

    2010-01-01

    Full Text Available Using high-intensity femtosecond laser pulses for surface structuring, technologically important metallic light absorbers (dark Au, W, and Ti alloy with absorption of about 85–95% over a broad wavelength range from ultraviolet to infrared were produced. It was found that the enhanced absorption of the dark metals is caused by a rich variety of nano-/microscale surface structures. The dark metals produced in this study may find a variety of applications in the fields of renewable energy and energy efficiency, such as thermophotovoltaics, solar energy absorbers, thermal radiation sources, and radiative heat transfer devices.

  9. Ultrashort-pulse laser excitation and damage of dielectric materials

    DEFF Research Database (Denmark)

    Haahr-Lillevang, Lasse; Balling, Peter

    2015-01-01

    Ultrashort-pulse laser excitation of dielectrics is an intricate problem due to the strong coupling between the rapidly changing material properties and the light. In the present paper, details of a model based on a multiple-rate-equation description of the conduction band are provided. The model...... is verified by comparison with recent experimental measurements of the transient optical properties in combination with ablation-depth determinations. The excitation process from the first creation of conduction-band electrons at low intensities to the formation of a highly-excited plasma and associated...

  10. Experimental investigations and statistical analysis of pulsed laser bending of AISI 304 stainless steel sheet

    Science.gov (United States)

    Maji, Kuntal; Pratihar, D. K.; Nath, A. K.

    2013-07-01

    This paper presents experimental investigations on pulsed laser bending of sheet metal and statistical analysis to study the effects of process parameters. Laser power, scan speed, spot diameter and pulsed duration were taken as input variables and bending angle was considered as the output. Response surface methodology was used for modeling and optimization of the pulsed laser bending process. The performance of the developed model was validated through the experiments. All the input variables were found to have significant influence on the bending angle. Bending angle increased with the increase of laser power and pulse duration and decreased with the increase of scan speed and spot diameter. The optimum process parameters for the maximum bending angle were also found and verified with experimental data. The effects of pulse frequency, pulse width and pulse energy on bending angle were also investigated through experiments. Bending angle was found to be the maximum for a certain value of pulse frequency. With the increase of pulse width, bending angle increased at constant laser power but decreased at constant pulse energy. Bending angle was seen to increase with the increase of spatial overlapping and decrease with the increase of gap at constant laser power, but it showed optimal values for both the cases at constant line energy. A comparative study between continuous and pulsed laser bending was carried out to study the process efficiency in terms of energy input and produced deformation.

  11. Graphene based widely-tunable and singly-polarized pulse generation with random fiber lasers

    Science.gov (United States)

    Yao, B. C.; Rao, Y. J.; Wang, Z. N.; Wu, Y.; Zhou, J. H.; Wu, H.; Fan, M. Q.; Cao, X. L.; Zhang, W. L.; Chen, Y. F.; Li, Y. R.; Churkin, D.; Turitsyn, S.; Wong, C. W.

    2015-12-01

    Pulse generation often requires a stabilized cavity and its corresponding mode structure for initial phase-locking. Contrastingly, modeless cavity-free random lasers provide new possibilities for high quantum efficiency lasing that could potentially be widely tunable spectrally and temporally. Pulse generation in random lasers, however, has remained elusive since the discovery of modeless gain lasing. Here we report coherent pulse generation with modeless random lasers based on the unique polarization selectivity and broadband saturable absorption of monolayer graphene. Simultaneous temporal compression of cavity-free pulses are observed with such a polarization modulation, along with a broadly-tunable pulsewidth across two orders of magnitude down to 900 ps, a broadly-tunable repetition rate across three orders of magnitude up to 3 MHz, and a singly-polarized pulse train at 41 dB extinction ratio, about an order of magnitude larger than conventional pulsed fiber lasers. Moreover, our graphene-based pulse formation also demonstrates robust pulse-to-pulse stability and wide-wavelength operation due to the cavity-less feature. Such a graphene-based architecture not only provides a tunable pulsed random laser for fiber-optic sensing, speckle-free imaging, and laser-material processing, but also a new way for the non-random CW fiber lasers to generate widely tunable and singly-polarized pulses.

  12. Ion beam control in laser plasma interaction

    Science.gov (United States)

    Kawata, S.; Izumiyama, T.; Sato, D.; Nagashima, T.; Takano, M.; Barada, D.; Gu, Y. J.; Ma, Y. Y.; Kong, Q.; Wang, P. X.; Wang, W. M.

    2016-03-01

    By a two-stage successive acceleration in laser ion acceleration, our 2.5-dimensional particle-in-cell simulations demonstrate a remarkable increase in ion energy by a few hundreds of MeV; the maximum proton energy reaches about 250MeV. The ions are accelerated by the inductive continuous post-acceleration in a laser plasma interaction together with the target normal sheath acceleration and the breakout afterburner mechanism. An intense short-pulse laser generates a strong current by high-energy electrons accelerated, when an intense short- pulse laser illuminates a plasma target. The strong electric current creates a strong magnetic field along the high-energy electron current in the plasma. During the increase phase in the magnetic field strength, the moving longitudinal inductive electric field is induced by the Faraday law, and accelerates the forward-moving ions continously. The multi-stage acceleration provides a unique controllability in the ion energy and its quality.

  13. Bioactive glass thin films synthesized by advanced pulsed laser techniques

    Science.gov (United States)

    Mihailescu, N.; Stan, George E.; Ristoscu, C.; Sopronyi, M.; Mihailescu, Ion N.

    2016-10-01

    Bioactive materials play an increasingly important role in the biomaterials industry, and are extensively used in a range of applications, including biodegradable metallic implants. We report on Bioactive Glasses (BG) films deposition by pulsed laser techniques onto biodegradable substrates. The BG coatings were obtained using a KrF* excimer laser source (λ= 248 nm, τFWHM ≤ 25 ns).Their thickness has been determined by Profilometry measurements, whilst their morphology has been analysed by Scanning Electron Microscopy (SEM). The obtained coatings fairly preserved the targets composition and structure, as revealed by Energy Dispersive X-Ray Spectroscopy, Grazing Incidence X-Ray Diffraction, and Fourier Transform Infra-Red Spectroscopy analyses.

  14. History and current status of commercial pulsed laser deposition equipment

    Science.gov (United States)

    Greer, James A.

    2014-01-01

    This paper will review the history of the scale-up of the pulsed laser deposition (PLD) process from small areas ∼1 cm2 up to 10 m2 starting in about 1987. It also documents the history of commercialization of PLD as various companies become involved in selling fully integrated laser deposition tools starting in 1989. The paper will highlight the current state of the art of commercial PLD equipment for R&D that is available on the market today from mainstream vendors as well as production-oriented applications directed at piezo-electric materials for microelectromechanical systems and high-temperature superconductors for coated-conductor applications. The paper clearly demonstrates that considerable improvements have been made to scaling this unique physical vapour deposition process to useful substrate sizes, and that commercial deposition equipment is readily available from a variety of vendors to address a wide variety of technologically important thin-film applications.

  15. Growth modes of pentacene films obtained by pulsed laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Wisz, G., E-mail: gwisz@univ.rzeszow.pl [Institute of Physics, University of Rzeszow, Rejtana 16a, 35-309 Rzeszow (Poland); Kuzma, M.; Virt, I.; Sagan, P. [Institute of Physics, University of Rzeszow, Rejtana 16a, 35-309 Rzeszow (Poland); Rudyj, I. [Lviv University of Technology, Bandery 12, 90-646 Lviv (Ukraine)

    2011-04-01

    Thin pentacene films were deposited on KCl and ITO/glass substrates by the pulsed laser deposition method (PLD) using a YAG:Nd{sup 3+} laser with a second harmonic ({lambda} = 532 nm). We compared the structure of the layer on differently oriented substrates with respect to the pentacene plasma plume - vertical and parallel orientation. The structure of the layers formed was examined using SEM, RHEED and THEED methods. The lattice parameters of the layer deposited on KCl were determined from THEED pattern (a = 5.928 A, b 7.874 A, c = 14,98 A, {alpha} = 76.54{sup o}, {beta} 75.17{sup o}, {gamma} = 89.20{sup o}). The preferred direction [11-bar 0] of the layer growth on KCl substrate was addressed. The effect of the substrate orientation results in a different growth mode of the layers.

  16. Bulk diamond optical waveguides fabricated by focused femtosecond laser pulses

    Science.gov (United States)

    Hadden, J. P.; Sotillo, Belén.; Bharadwaj, Vibhav; Rampini, Stefano; Bosia, Federico; Picollo, Federico; Sakakura, Masaaki; Chiappini, Andrea; Fernandez, Toney T.; Osellame, Roberto; Miura, Kiyotaka; Ferrari, Maurizio; Ramponi, Roberta; Olivero, Paolo; Barclay, Paul E.; Eaton, Shane M.

    2017-02-01

    Diamond's nitrogen-vacancy (NV) centers show great promise in sensing applications and quantum computing due to their long electron spin coherence time and their ability to be located, manipulated and read out using light. The electrons of the NV center, largely localized at the vacancy site, combine to form a spin triplet, which can be polarized with 532- nm laser light, even at room temperature. The NV's states are isolated from environmental perturbations making their spin coherence comparable to trapped ions. An important breakthrough would be in connecting, using waveguides, multiple diamond NVs together optically. However, the inertness of diamond is a significant hurdle for the fabrication of integrated optics similar to those that revolutionized silicon photonics. In this work we show the possibility of buried waveguide fabrication in diamond, enabled by focused femtosecond high repetition rate laser pulses. We use μRaman spectroscopy to gain better insight into the structure and refractive index profile of the optical waveguides.

  17. Modeling laser pulse evolution in ionizing gas and plasma with application to laser wakefield acceleration

    Science.gov (United States)

    Cooley, James Hamilton

    The interaction of high intensity laser pulses with matter is of current research interest not only for potential applications but also due to the interesting non-linear process that can occur with current experimental facilities. Understanding many of the non-linear processes requires significant modeling and simulation effort. We explore several aspects of laser pulse evolution and plasma response in simulations ranging from modeling laser wakefield accelerators to modeling basic ionization processes. First, we present a model that describes the onset and growth of axial modulation found experimentally during the formation of plasma channels formed using an axicon lens. We provide a systematic development that describes this new type of parametric instability and explains the pressure dependence and the mechanism for formation of these axial modulations in the channel. Next, we describe details of a new three-dimensional laser pulse evolution code that we have developed to model propagation in tenuous gas and plasma and we provide relevant information about the validation and testing of the code. We then use this new code to examine the three-dimensional structure of the laser pulse evolving in the presence of ionizing gas. In particular we present results from the first three-dimensional study of the ionization scattering instability. Finally, we examine injecting electrons into laser wakefield accelerators. We examine in detail the injection and trapping characteristics for an electron beam with an initially broad energy distribution and look at the effect of beam loading on the trapping efficiency. We present estimates for the maximum charge that can be trapped from a low energy beam with a Boltzmann type energy distribution.

  18. Fast Micromachining Using Spatial Light Modulator and Galvanometer Scanner with Infrared Pulsed Nanosecond Fiber Laser

    National Research Council Canada - National Science Library

    Jarno J J Kaakkunen; Ilkka Vanttaja; Petri Laakso

    2014-01-01

    ...) and a galvanometer scanner with an infrared nanosecond fiber lasers is studied. Here, the SLM is used as a computer generated hologram which can be applied to modify laser pulses intensity distribution virtually almost arbitrary...

  19. Reliability of High Power Laser Diode Arrays Operating in Long Pulse Mode

    Science.gov (United States)

    Amzajerdian, Farzin; Meadows, Byron L.; Barnes, Bruce W.; Lockard, George E.; Singh, Upendra N.; Kavaya, Michael J.; Baker, Nathaniel R.

    2006-01-01

    Reliability and lifetime of quasi-CW laser diode arrays are greatly influenced by their thermal characteristics. This paper examines the thermal properties of laser diode arrays operating in long pulse duration regime.

  20. An informal teaching of light and lasers through the CSIR-NLC PULSE programme

    CSIR Research Space (South Africa)

    Shikwambana, L

    2012-07-01

    Full Text Available The PULSE programme of the CSIR relates to the public understanding of laser science and engineering and the awareness of laser science and engineering to schools and tertiary institutions....

  1. Antibacterial effects of pulsed Nd:YAG laser radiation at different energy settings in root canals.

    Science.gov (United States)

    Folwaczny, Matthias; Mehl, Albert; Jordan, Christian; Hickel, Reinhard

    2002-01-01

    The in vitro study aimed at the determination of the bacterial reduction in root canals used pulsed Nd:YAG laser radiation without a photosensitizing dye. In addition the temperature change in the root canals was determined during laser irradiation. The study sample was 114 root canals of extracted single-rooted human teeth that have been enlarged mechanically, sterilized, and randomly assigned to two experimental units. The source of radiation was a Nd:YAG laser device emitting pulsed infrared radiation at a wavelength of 1.064 microm, a pulse duration of 100 micros, and a pulse repetition rate of 20 pps. Samples of each experimental unit were inoculated with Escherichia coli (ATCC 25922) or Staphylococcus aureus (ATCC 25923), respectively, and divided into subgroups of 13 teeth each for irradiation for 20 s at 100 mJ or 200 mJ. One subgroup was left untreated as positive control and one subgroup was rinsed with 0.5 ml of sodium hypochloride. After laser treatment or rinsing with sodium hypochloride the number of bacteria in each root canal was determined using the surface spread plate technique. Statistical analysis of the results was performed with ANOVA and Scheffé test at a level of significance of 5% (p temperature increase at 100 mJ was 24.3 degrees C (+/-3.9) and that at 200 mJ was 61.8 degrees C (+/-4.2). The Nd:YAG laser radiation has antimicrobial effects in root canals even in the absence of photosensitizing dyes but also causes considerable temperature increase.

  2. Treatment of rosacea with long-pulsed Nd: YAG laser

    Directory of Open Access Journals (Sweden)

    Ekin Meşe Say

    2013-03-01

    Full Text Available Background and Design: Rosacea is a chronic inflammatory disorder of the face. There is no curative treatment for the disease. Facial flushing and vascular lesions due to rosacea may significantly affect a patient’s quality of life. Topical and oral antibiotics are not effective for treating rosacea. Currently, laser treatment of vascular lesions has been reported in the literature. We aimed to investigate the efficacy of long-pulse 1064-nm neodymium: YAG (Nd: YAG laser in the treatment of vascular lesions (erythema and telangiectasia in rosacea patients. Materials and Methods: Thirty-nine patients (29 women, 10 men with erythematotelangiectatic rosacea (ETR were recruited into the study. Severity of the disease (ETR-score: 0-3 was assessed for all patients. We used long-pulsed Nd: YAG laser for vascular lesions at 3-4 weeks intervals. The face was divided into seven anatomic regions for evaluation. Assessment was made by comparing pretreatment and posttreatment photographs by using ETR-scores. For evaluating patient satisfaction, a scale of 0 to 3 was used. Results: The patients were divided into three groups according to the ETR scores [ETR-1 (n=12, ETR-2 (n=9, ETR-3 (n=18]. Following an average of 3.95 (2-8 sessions laser treatments, the clinical improvement was statistically significant in all groups (p<0.05. The mean reduction of ETR-score was 91.70% in patients with ETR-1 and. the clinical improvement was to be decreased in severe forms of ETR. The most common sites for the lesions were the malar region, ala nasi and the nasal dorsum, respectively. The lesions on the ala nasi were more recalcitrant to the treatment than those on the other areas. Regarding to physician assessment of treatment’s success, 97% of the patients was associated with moderate and excellent improvement. According to physicians’ assessment, excellent improvement was noticed in 43.58% and, 61.5% of patients reported a high degree of satisfaction with this

  3. Impact of pulse duration on Ho:YAG laser lithotripsy: fragmentation and dusting performance.

    Science.gov (United States)

    Bader, Markus J; Pongratz, Thomas; Khoder, Wael; Stief, Christian G; Herrmann, Thomas; Nagele, Udo; Sroka, Ronald

    2015-04-01

    In vitro investigations of Ho:YAG laser-induced stone fragmentation were performed to identify potential impacts of different pulse durations on stone fragmentation characteristics. A Ho:YAG laser system (Swiss LaserClast, EMS S.A., Nyon, Switzerland) with selectable long or short pulse mode was tested with regard to its fragmentation and laser hardware compatibility properties. The pulse duration is depending on the specific laser parameters. Fragmentation tests (hand-held, hands-free, single-pulse-induced crater) on artificial BEGO stones were performed under reproducible experimental conditions (fibre sizes: 365 and 200 µm; laser settings: 10 W through combinations of 0.5, 1, 2 J/pulse and 20, 10, 5 Hz, respectively). Differences in fragmentation rates between the two pulse duration regimes were detected with statistical significance for defined settings. Hand-held and motivated Ho:YAG laser-assisted fragmentation of BEGO stones showed no significant difference between short pulse mode and long pulse mode, neither in fragmentation rates nor in number of fragments and fragment sizes. Similarly, the results of the hands-free fragmentation tests (with and without anti-repulsion device) showed no statistical differences between long pulse and short pulse modes. The study showed that fragmentation rates for long and short pulse durations at identical power settings remain at a comparable level. Longer holmium laser pulse duration reduces stone pushback. Therefore, longer laser pulses may result in better clinical outcome of laser lithotripsy and more convenient handling during clinical use without compromising fragmentation effectiveness.

  4. Femtosecond pulsed laser processing of electronic materials: Fundamentals and micro/nano-scale applications

    Science.gov (United States)

    Choi, Tae-Youl

    Ultra-short pulsed laser radiation has been shown to be effective for precision materials processing and surface micro-modification. One of advantages is the substantial reduction of the heat penetration depth, which leads to minimal lateral damage. Other advantages include non-thermal nature of ablation process, controlled ablation and ideal characteristics for precision micro-structuring. Yet, fundamental questions remain unsolved regarding the nature of melting and ablation mechanisms in femtosecond laser processing of materials. In addition to micro engineering problems, nano-structuring and nano-fabrication are emerging fields that are of particular interest in conjunction with femtosecond laser processing. A comprehensive experimental study as well as theoretical development is presented to address these issues. Ultra-short pulsed laser irradiation was used to crystallize 100 nm amorphous silicon (a-Si) films. The crystallization process was observed by time-resolved pump-and-probe reflection imaging in the range of 0.2 ps to 100 ns. The in-situ images in conjunction with post-processed SEM and AFM mapping of the crystallized structure provide evidence for non-thermal ultra-fast phase transition and subsequent surface-initiated crystallization. Mechanisms of ultra-fast laser-induced ablation on crystalline silicon and copper are investigated by time-resolved pump-and-probe microscopy in normal imaging and shadowgraph arrangements. A one-dimensional model of the energy transport is utilized to predict the carrier temperature and lattice temperature as well as the electron and vapor flux emitted from the surface. The temporal delay between the pump and probe pulses was set by a precision translation stage up to about 500 ps and then extended to the nanosecond regime by an optical fiber assembly. The ejection of material was observed at several picoseconds to tens of nanoseconds after the main (pump) pulse by high-resolution, ultra-fast shadowgraphs. The

  5. The effect of laser contrast on generation of highly charged Fe ions by ultra-intense femtosecond laser pulses

    Science.gov (United States)

    Faenov, Anatoly Ya.; Alkhimova, Maria A.; Pikuz, Tatiana A.; Skobelev, Igor Yu.; Nishiuchi, Mamiko; Sakaki, Hironao; Pirozhkov, Alexander S.; Sagisaka, Akito; Dover, Nicholas P.; Kondo, Kotaro; Ogura, Koichi; Fukuda, Yuji; Kiriyama, Hiromitsu; Andreev, Alexander; Nishitani, Keita; Miyahara, Takumi; Watanabe, Yukinobu; Pikuz, Sergey A.; Kando, Masaki; Kodama, Ruosuke; Kondo, Kiminori

    2017-07-01

    Experimental studies on the formation of highly charged ions of medium-Z elements using femtosecond laser pulses with different contrast levels were carried out. Multiply charged Fe ions were generated by laser pulses with 35 fs duration and an intensity exceeding 1021 W/cm2. Using high-resolution X-ray spectroscopic methods, bulk electron temperature of the generated plasma has been identified. It is shown that the presence of a laser pre-pulse at a contrast level of 105-106 with respect to the main pulse drastically decreases the degree of Fe ionization. We conclude that an effective source of energetic, multiply charged moderate and high- Z ions based on femtosecond laser-plasma interactions can be created only using laser pulses of ultra-high contrast.

  6. Clinical laser angioplasty with a pulsed neodymium:YAG laser: long-term followup

    Science.gov (United States)

    Lawrence, Roy N.; Michaels, Jonathan A.; Cross, Frank W.; Raphael, Michael; Adiseshiah, M.; Marston, A.

    1992-08-01

    Since December 1986, 140 laser angioplasty procedures have been carried out using a pulsed Nd:YAG laser (Lumonics Ltd. Rugby, UK). The laser produces 100 microsecond(s) ec pulses at a wavelength of 1064 nm and a repetition rate of 10 Hz. All procedures were carried out for critical ischaemia or severe claudication in patients who had complete occlusion of the superficial femoral artery (SFA). All occlusions were over 5 cm in length or previous failures of balloon angioplasty and would otherwise have proceeded to bypass surgery. The occlusion was approached percutaneously via the ipsilateral femoral artery and successful recanalization was followed by balloon dilatation. Problems with access were encountered in 18% of the procedures, about half of which were subsequently repeated with successful access. There was failure of recanalization in 26% of the cases, five due to vessel perforation. These did not result in clinical sequelae. Early occlusion (procedure (range 3 - 47 months). Of the 19 patients who reoccluded, (mean 12.1 months, range 1 - 26 months), seven had bypass grafts, three underwent amputation (all three presented with rest pain), two had repeat laser procedures, and seven were treated conservatively. Thirteen percent of the patients have died, chiefly from cardiovascular disease elsewhere. Overall, continued patency has been achieved in 32% of limbs considered for laser treatment, but this rises to 60% of all initially successful procedures. In conclusion, laser angioplasty may avoid the need for vascular surgery in a significant number of patients.

  7. Formation of Stable Polymer Glasses via Matrix Assisted Pulsed Laser Evaporation

    Science.gov (United States)

    Shepard, Kimberly; Guo, Yunlong; Priestley, Rodney

    2012-02-01

    Via Matrix Assisted Pulsed Laser Evaporation (MAPLE), we are able to form amorphous polymer films that exhibit significant changes in material properties and structure. In the MAPLE method, a pulsed laser ablates a target, consisting of a frozen dilute solution of the desired polymer, in order to produce films of the material. By carefully controlling the growth rate of film formation and the substrate temperature during deposition, we are able to form glassy films with structures that are either less or more dense compared to the standard glass. Interestingly, the morphology of the low and high-density amorphous films is significantly different. The low-density glasses are nanostructured and the high-density glasses are not. In this poster, we discuss how MAPLE can be used to tune the morphology and hence, the properties of polymer glasses.

  8. SOLID BODY ABLATION UNDER EXPOSURE TO ULTRA SHORT LASER PULSES: STUDY BY MOLECULAR DYNAMICS METHODS

    OpenAIRE

    D. S. Ivanov; V. P. Veiko; Y. B. Yakovlev; M. E. Carcia; Rethfeld, B.

    2014-01-01

    The process of laser ablation under the influence of ultra short laser pulses on metals is investigated by methods of molecular dynamics. The validity and applicability of the hybrid atomistic-continuous model for the estimation of optimum modes of ultra short laser pulses processing are explored. Combination of atomistic model of laser-induced non-equilibrium process of a phase transition at the atomic level with continuous two-temperature model for describing the dynamics of photo-excitatio...

  9. Effects of Beam Size and Pulse Duration on the Laser Drilling Process

    CERN Document Server

    Afrin, Nazia; Chen, J K; Zhang, Yuwen

    2016-01-01

    A two-dimensional axisymmetric transient laser drilling model is used to analyze the effects of laser beam diameter and laser pulse duration on the laser drilling process. The model includes conduction and convection heat transfer, melting, solidification and vaporization, as well as material removal resulting from the vaporization and melt ejection. The validated model is applied to study the effects of laser beam size and pulse duration on the geometry of the drilled hole. It is found that the ablation effect decrease with the increasing beam diameter due to the effect of increased vaporization rate, and deeper hole is observed for the larger pulse width due to the higher thermal ablation efficiency.

  10. Electra: Repetitively Pulsed Angularly Multiplexed KrF Laser System Performance

    Science.gov (United States)

    Wolford, Matthew; Myers, Matthew; Giuliani, John; Sethian, John; Burns, Patrick; Hegeler, Frank; Jaynes, Reginald

    2008-11-01

    As in a full size fusion power plant beam line, Electra is a multistage laser amplifier system. The multistage amplifier system consists of a commercial discharge laser and two doubled sided electron beam pumped amplifiers. Angular multiplexing is used in the optical layout to provide pulse length control and to maximize laser extraction from the amplifiers. Two angularly multiplexed beams have extracted 30 J of KrF laser light with an aperture 8 x 10 cm^2, which is sufficient to extract over 500 J from the main amplifier and models agree. The main amplifier of Electra in oscillator mode has demonstrated single shot and rep-rate laser energies exceeding 700 J with 100 ns pulsewidth at 248 nm with an aperture 29 x 29 cm^2. Continuous operation of the KrF electron beam pumped oscillator has lasted for more than 2.5 hours without failure at 1 Hz and 2.5 Hz. The measured intensity and pulse energy for durations greater than thousand shots are consistent at measurable rep-rates of 1 Hz, 2.5 Hz and 5 Hz.

  11. Laser controlled flame stabilization

    Science.gov (United States)

    Early, James W.; Thomas, Matthew E.

    2001-01-01

    A method and apparatus is provided for initiating and stabilizing fuel combustion in applications such as gas turbine electrical power generating engines and jet turbine engines where it is desired to burn lean fuel/air mixtures which produce lower amounts of NO.sub.x. A laser induced spark is propagated at a distance from the fuel nozzle with the laser ignitor being remotely located from the high temperature environment of the combustion chamber. A laser initiating spark generated by focusing high peak power laser light to a sufficiently tight laser spot within the fuel to cause the ionization of air and fuel into a plasma is unobtrusive to the flow dynamics of the combustion chamber of a fuel injector, thereby facilitating whatever advantage can be taken of flow dynamics in the design of the fuel injector.

  12. Shadowgraphic imaging of metal drilling with a long pulse excimer laser

    NARCIS (Netherlands)

    Schoonderbeek, A.; Biesheuvel, C.A.; Hofstra, R.M.; Boller, Klaus J.; Meijer, J.; Miyamoto, Isamu; Ostendorf, Andreas; Sugioka, Koji; Helvajian, Henry

    2003-01-01

    A shadowgraphic imaging technique is used for studying the interaction between the laser beam and the material during laser drilling. The used laser is a XeCl excimer laser with a nearly diffraction limited beam and 175 ns pulse length. We studied how and when the material is removed. Holes are

  13. Novel doped hydroxyapatite thin films obtained by pulsed laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Duta, L. [National Institute for Lasers, Plasma and Radiation Physics, Lasers Department, 409 Atomistilor Street, Magurele (Romania); Oktar, F.N. [Department of Bioengineering, Faculty of Engineering, Marmara University, Goztepe, Istanbul 34722 (Turkey); Department of Medical Imaging Technics, Vocational School of Health Services, Marmara University, Uskudar, Istanbul 34668 (Turkey); Nanotechnology and Biomaterials Application and Research Centre, Marmara University, Istanbul (Turkey); Stan, G.E. [National Institute of Materials Physics, 105 Bis Atomistilor Street, Magurele (Romania); Popescu-Pelin, G.; Serban, N.; Luculescu, C. [National Institute for Lasers, Plasma and Radiation Physics, Lasers Department, 409 Atomistilor Street, Magurele (Romania); Mihailescu, I.N., E-mail: ion.mihailescu@inflpr.ro [National Institute for Lasers, Plasma and Radiation Physics, Lasers Department, 409 Atomistilor Street, Magurele (Romania)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer HA coatings synthesized by pulsed laser deposition. Black-Right-Pointing-Pointer Comparative study of commercial vs. animal origin materials. Black-Right-Pointing-Pointer HA coatings of animal origin were rougher and more adherent to substrates. Black-Right-Pointing-Pointer Animal origin films can be considered as promising candidates for implant coatings. - Abstract: We report on the synthesis of novel ovine and bovine derived hydroxyapatite thin films on titanium substrates by pulsed laser deposition for a new generation of implants. The calcination treatment applied to produce the hydroxyapatite powders from ovine/bovine bones was intended to induce crystallization and to prohibit the transmission of diseases. The deposited films were characterized by scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and energy dispersive X-ray spectroscopy. Pull-off adherence and profilometry measurements were also carried out. X-ray diffraction ascertained the polycrystalline hydroxyapatite nature of the powders and films. Fourier transform infrared spectroscopy evidenced the vibrational bands characteristic to a hydroxyapatite material slightly carbonated. The micrographs of the films showed a uniform distribution of spheroidal particulates with a mean diameter of {approx}2 {mu}m. Pull-off measurements demonstrated excellent bonding strength values between the hydroxyapatite films and the titanium substrates. Because of their physical-chemical properties and low cost fabrication from renewable resources, we think that these new coating materials could be considered as a prospective competitor to synthetic hydroxyapatite used for implantology applications.

  14. Picosecond and subpicosecond pulsed laser deposition of Pb thin films

    Directory of Open Access Journals (Sweden)

    F. Gontad

    2013-09-01

    Full Text Available Pb thin films were deposited on Nb substrates by means of pulsed laser deposition (PLD with UV radiation (248 nm, in two different ablation regimes: picosecond (5 ps and subpicosecond (0.5 ps. Granular films with grain size on the micron scale have been obtained, with no evidence of large droplet formation. All films presented a polycrystalline character with preferential orientation along the (111 crystalline planes. A maximum quantum efficiency (QE of 7.3×10^{-5} (at 266 nm and 7 ns pulse duration was measured, after laser cleaning, demonstrating good photoemission performance for Pb thin films deposited by ultrashort PLD. Moreover, Pb thin film photocathodes have maintained their QE for days, providing excellent chemical stability and durability. These results suggest that Pb thin films deposited on Nb by ultrashort PLD are a noteworthy alternative for the fabrication of photocathodes for superconductive radio-frequency electron guns. Finally, a comparison with the characteristics of Pb films prepared by ns PLD is illustrated and discussed.

  15. Single and double long pulse laser ablation of aluminum induced in air and water ambient

    Energy Technology Data Exchange (ETDEWEB)

    Akbari Jafarabadi, Marzieh; Mahdieh, Mohammad Hossein, E-mail: mahdm@iust.ac.ir

    2017-02-28

    Highlights: • Laser ablation of aluminum target by single and double pulse (∼ 5 ns delay) in ambient air and distilled water • Comparing with air, in ambient water, plasma confinement results in higher crater depth. • In comparison with single pulse laser ablation, the absorption of the laser pulse energy is higher for double pulse regime. • As a result of ablated material expansion, the crater depth is decreased if the target is placed at lower depth. - Abstract: In this paper, single pulse and double pulse laser ablation of an aluminum target in two interaction ambient was investigated experimentally. The interaction was performed by nanosecond Nd:YAG laser beam in air and four depths (i.e. 9, 13, 17, and 21 mm) of distilled water ambient. The irradiation was carried out in single and collinear double pulse configurations in both air and liquid ambient. Crater geometry (depth and diameter) was measured by an optical microscope. The results indicated that the crater geometry strongly depends on both single pulse and double pulse configurations and interaction ambient. In single pulse regime, the crater diameter is higher for all water depths compared to that of air. However, the crater depth, depend on water depth, is higher or lower than the crater depth in air. In double pulse laser ablation, there are greater values for both crater diameters and crater depths in the water.

  16. Ablation experiment and threshold calculation of titanium alloy irradiated by ultra-fast pulse laser

    Directory of Open Access Journals (Sweden)

    Buxiang Zheng

    2014-02-01

    Full Text Available The interaction between an ultra-fast pulse laser and a material's surface has become a research hotspot in recent years. Micromachining of titanium alloy with an ultra-fast pulse laser is a very important research direction, and it has very important theoretical significance and application value in investigating the ablation threshold of titanium alloy irradiated by ultra-fast pulse lasers. Irradiated by a picosecond pulse laser with wavelengths of 1064 nm and 532 nm, the surface morphology and feature sizes, including ablation crater width (i.e. diameter, ablation depth, ablation area, ablation volume, single pulse ablation rate, and so forth, of the titanium alloy were studied, and their ablation distributions were obtained. The experimental results show that titanium alloy irradiated by a picosecond pulse infrared laser with a 1064 nm wavelength has better ablation morphology than that of the green picosecond pulse laser with a 532 nm wavelength. The feature sizes are approximately linearly dependent on the laser pulse energy density at low energy density and the monotonic increase in laser pulse energy density. With the increase in energy density, the ablation feature sizes are increased. The rate of increase in the feature sizes slows down gradually once the energy density reaches a certain value, and gradually saturated trends occur at a relatively high energy density. Based on the linear relation between the laser pulse energy density and the crater area of the titanium alloy surface, and the Gaussian distribution of the laser intensity on the cross section, the ablation threshold of titanium alloy irradiated by an ultra-fast pulse laser was calculated to be about 0.109 J/cm2.

  17. Controlling the acoustic streaming by pulsed ultrasounds.

    Science.gov (United States)

    Hoyos, Mauricio; Castro, Angélica

    2013-01-01

    We propose a technique based on pulsed ultrasounds for controlling, reducing to a minimum observable value the acoustic streaming in closed ultrasonic standing wave fluidic resonators. By modifying the number of pulses and the repetition time it is possible to reduce the velocity of the acoustic streaming with respect to the velocity generated by the continuous ultrasound mode of operation. The acoustic streaming is observed at the nodal plane where a suspension of 800nm latex particles was focused by primary radiation force. A mixture of 800nm and 15μm latex particles has been also used for showing that the acoustic streaming is hardly reduced while primary and secondary forces continue to operate. The parameter we call "pulse mode factor" i.e. the time of applied ultrasound divided by the duty cycle, is found to be the adequate parameter that controls the acoustic streaming. We demonstrate that pulsed ultrasound is more efficient for controlling the acoustic streaming than the variation of the amplitude of the standing waves. Copyright © 2012 Elsevier B.V. All rights reserved.

  18. Comparison of 2 pulsed lasers for lithotripsy of ureteral calculi: report on 154 patients.

    Science.gov (United States)

    Benizri, E; Wodey, J; Amiel, J; Toubol, J

    1993-12-01

    Extracorporeal lithotripsy does not always provide satisfactory results for the treatment of ureteral stones. Such cases appear to be excellent indications for endocorporeal lithotripsy based on an association of ureteroscopy and laser. To compare the performances of 2 pulsed lasers, the pulsed dye laser (Candela) and solid Q switched laser (HMT), for the treatment of these calculi 161 ureteral stones were treated successively from November 1990 to March 1992 by a combination of ureteroscopy and laser. Endocorporeal lithotripsy was performed in 102 cases with the Candela laser, in 47 with the HMT laser and in 7 with both lasers. With a stable success rate greater than 90%, both lasers demonstrated equivalent performances regardless of the location of the stone along the ureter. However, while stone fragmentation was more rapid with the Candela laser, the HMT laser appeared to be more effective for dark stones (monohydrate calcium oxidate).

  19. Enhancement mechanism of femtosecond double-pulse laser-induced Cu plasma spectroscopy

    Science.gov (United States)

    Zhang, Dan; Chen, Anmin; Wang, Xiaowei; Li, Suyu; Wang, Ying; Sui, Laizhi; Jiang, Yuanfei; Jin, Mingxing

    2017-11-01

    A dual-wavelength femtosecond double-pulse laser is used to induce the Cu plasma spectroscopy in air. The laser wavelengths are a fundamental wavelength (800 nm) and a second harmonic wavelength (400 nm) from Ti:sapphire laser. The inter-pulse delay of double-pulse is from -300 ps to 160 ps. The observed spectral intensity is dependent on the inter-pulse delay of the dual-wavelength femtosecond double-pulse. We analyze the characteristics of the plasma temperature and the electron number density on the inter-pulse delay of double-pulse with two different wavelengths. For 800 nm + 400 nm, the spectral emission enhancement is based on more material ablation. For 400 nm + 800 nm, the enhanced mechanism is plasma reheating effect. This study will provide a better way to understand the mechanism of femtosecond double-pulse LIBS.

  20. Generation of 25-TW Femtosecond Laser Pulses at 515 nm with Extremely High Temporal Contrast

    Directory of Open Access Journals (Sweden)

    Marco Hornung

    2015-12-01

    Full Text Available We report on the frequency doubling of femtosecond laser pulses at 1030 nm center wavelength generated from the fully diode-pumped laser system POLARIS. The newly generated pulses at a center wavelength of 515 nm have a pulse energy of 3 J with a pulse duration of 120 fs. On the basis of initially ultra-high contrast seed pulses we expect a temporal intensity contrast better 10 17 200 ps before the peak of the main pulse. We analyzed the temporal intensity contrast from milliseconds to femtoseconds with a dynamic range covering more than 20 orders of magnitude. The pulses were focussed with a f/2-focussing parabola resulting in a peak intensity exceeding 10 20 W / cm 2 . The peak power and intensity are to the best of our knowledge the highest values for 515 nm-laser-pulses achieved so far.

  1. Laser Energy Monitor for Double-Pulsed 2-Micrometer IPDA Lidar Application

    Science.gov (United States)

    Refaat, Tamer F.; Petros, Mulugeta; Remus, Ruben; Yu, Jirong; Singh, Upendra N.

    2014-01-01

    Integrated path differential absorption (IPDA) lidar is a remote sensing technique for monitoring different atmospheric species. The technique relies on wavelength differentiation between strong and weak absorbing features normalized to the transmitted energy. 2-micron double-pulsed IPDA lidar is best suited for atmospheric carbon dioxide measurements. In such case, the transmitter produces two successive laser pulses separated by short interval (200 microseconds), with low repetition rate (10Hz). Conventional laser energy monitors, based on thermal detectors, are suitable for low repetition rate single pulse lasers. Due to the short pulse interval in double-pulsed lasers, thermal energy monitors underestimate the total transmitted energy. This leads to measurement biases and errors in double-pulsed IPDA technique. The design and calibration of a 2-micron double-pulse laser energy monitor is presented. The design is based on a high-speed, extended range InGaAs pin quantum detectors suitable for separating the two pulse events. Pulse integration is applied for converting the detected pulse power into energy. Results are compared to a photo-electro-magnetic (PEM) detector for impulse response verification. Calibration included comparing the three detection technologies in single-pulsed mode, then comparing the pin and PEM detectors in double-pulsed mode. Energy monitor linearity will be addressed.

  2. Ultraviolet pulsed laser irradiation of multi-walled carbon nanotubes in nitrogen atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Pérez del Pino, Ángel, E-mail: aperez@icmab.es; Cabana, Laura; Tobias, Gerard [Instituto de Ciencia de Materiales de Barcelona, Consejo Superior de Investigaciones Científicas (ICMAB-CSIC), Campus UAB, 08193 Bellaterra (Spain); György, Enikö [Instituto de Ciencia de Materiales de Barcelona, Consejo Superior de Investigaciones Científicas (ICMAB-CSIC), Campus UAB, 08193 Bellaterra (Spain); National Institute for Lasers, Plasma and Radiation Physics, P. O. Box MG 36, 76900 Bucharest V (Romania); Ballesteros, Belén [ICN2—Institut Catala de Nanociencia i Nanotecnologia, Campus UAB, 08193 Bellaterra, Barcelona (Spain)

    2014-03-07

    Laser irradiation of randomly oriented multi-walled carbon nanotube (MWCNT) networks has been carried out using a pulsed Nd:YAG UV laser in nitrogen gas environment. The evolution of the MWCNT morphology and structure as a function of laser fluence and number of accumulated laser pulses has been studied using electron microscopies and Raman spectroscopy. The observed changes are discussed and correlated with thermal simulations. The obtained results indicate that laser irradiation induces very fast, high temperature thermal cycles in MWCNTs which produce the formation of different nanocarbon forms, such as nanodiamonds. Premelting processes have been observed in localized sites by irradiation at low number of laser pulses and low fluence values. The accumulation of laser pulses and the increase in the fluence cause the full melting and amorphization of MWCNTs. The observed structural changes differ from that of conventional high temperature annealing treatments of MWCNTs.

  3. Infrared Pulse-laser Long-path Absorption Measurement of Carbon Dioxide Using a Raman-shifted Dye Laser

    Science.gov (United States)

    Minato, Atsushi; Sugimoto, Nobuo; Sasano, Yasuhiro

    1992-01-01

    A pulsed laser source is effective in infrared laser long-path absorption measurements when the optical path length is very long or the reflection from a hard target is utilized, because higher signal-to-noise ratio is obtained in the detection of weak return signals. We have investigated the performance of a pulse-laser long-path absorption system using a hydrogen Raman shifter and a tunable dye laser pumped by a Nd:YAG laser, which generates second Stokes radiation in the 2-micron region.

  4. Femtosecond pulsed laser deposition of biological and biocompatible thin layers

    Energy Technology Data Exchange (ETDEWEB)

    Hopp, B. [Hungarian Academy of Sciences, University of Szeged, Research Group on Laser Physics, Dom ter 9, H-6720 Szeged (Hungary)]. E-mail: bhopp@physx.u-szeged.hu; Smausz, T. [Hungarian Academy of Sciences, University of Szeged, Research Group on Laser Physics, Dom ter 9, H-6720 Szeged (Hungary); Kecskemeti, G. [Department of Optics and Quantum Electronics, University of Szeged, Dom ter 9, H-6720 Szeged (Hungary); Klini, A. [Institute of Electronic Structure and Laser (I.E.S.L.), Foundation for Research and Technology-Hellas (F.O.R.T.H.), P.O. Box 1527, GR-711 10 Heraklion, Crete (Greece); Bor, Zs. [Department of Optics and Quantum Electronics, University of Szeged, Dom ter 9, H-6720 Szeged (Hungary)

    2007-07-31

    In our study we investigate and report the femtosecond pulsed laser deposition of biological and biocompatible materials. Teflon, polyhydroxybutyrate, polyglycolic-acid, pepsin and tooth in the form of pressed pellets were used as target materials. Thin layers were deposited using pulses from a femtosecond KrF excimer laser system (FWHM = 450 fs, {lambda} = 248 nm, f = 10 Hz) at different fluences: 0.6, 0.9, 1.6, 2.2, 2.8 and 3.5 J/cm{sup 2}, respectively. Potassium bromide were used as substrates for diagnostic measurements of the films on a FTIR spectrometer. The pressure in the PLD chamber was 1 x 10{sup -3} Pa, and in the case of tooth and Teflon the substrates were heated at 250 deg. C. Under the optimized conditions the chemical structure of the deposited materials seemed to be largely preserved as evidenced by the corresponding IR spectra. The polyglycolic-acid films showed new spectral features indicating considerable morphological changes during PLD. Surface structure and thickness of the layers deposited on Si substrates were examined by an atomic force microscopy (AFM) and a surface profilometer. An empirical model has been elaborated for the description of the femtosecond PLD process. According to this the laser photons are absorbed in the surface layer of target resulting in chemical dissociation of molecules. The fast decomposition causes explosion-like gas expansion generating recoil forces which can tear off and accelerate solid particles. These grains containing target molecules without any chemical damages are ejected from the target and deposited onto the substrate forming a thin layer.

  5. Laser dynamics of a mode-locked thulium/holmium fiber laser in the solitonic and the stretched pulse regimes

    Science.gov (United States)

    Kadel, Rajesh

    Mode-locked lasers that produce short optical pulses in the mid-infrared wavelength region have been sought out for a wide range of applications such as free space communication, molecular spectroscopy, medical diagnostics, and remote sensing. Here, a thulium and holmium (Tm/Ho) co-doped fiber laser that mode-locks in both the solitonic and stretched-pulse regimes is used to produce ultra-short pulses in the 2 mum region. Nonlinear polarization rotation technique is used where fiber nonlinearity is responsible to mode-lock the laser. The anomalous group velocity dispersion of both the single mode and gain fibers used limit the laser operation in the solitonic regime where spectral bandwidth is 10 nm and hence the pulse duration is limited to 996 fs. In order to increase the spectral bandwidth and hence get the shorter pulses the anomalous dispersion of these fibers has to compensate using normal group velocity dispersion fiber in the laser cavity. High numerical aperture fibers, which have normal group velocity dispersion around 2 mum due to its large and positive waveguide dispersion, can be used to compensate the anomalous dispersion of the gain and single mode fibers. We used a high numerical aperture fiber called UHNA4 in the laser cavity in order to compensate the anomalous dispersion of other fibers and mode-locked the laser in stretched pulse regime. The spectral bandwidth of the laser increased to 31 nm with corresponding pulse duration of 450 fs measured from the interferometric autocorrelation. The laser dynamics of the Tm/Ho co-doped fiber laser is also studied while going from the stretched-pulse to solitonic regime by fiber cut-back measurements of normal dispersion fiber. It was clearly observed that both the spectral bandwidth and the pulse duration changed significantly going from one region to the other.

  6. A quantum dynamics study of the benzopyran ring opening guided by laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Saab, Mohamad, E-mail: mohamad.saab@univ-montp2.fr [CTMM, Institut Charles Gerhardt Montpellier (UMR5253), CC 15001, Université Montpellier 2, F-34095 Montpellier (France); Doriol, Loïc Joubert, E-mail: Loic.Joubert-Doriol@univ-montp2.fr [CTMM, Institut Charles Gerhardt Montpellier (UMR5253), CC 15001, Université Montpellier 2, F-34095 Montpellier (France); Lasorne, Benjamin, E-mail: lasorne@univ-montp2.fr [CTMM, Institut Charles Gerhardt Montpellier (UMR5253), CC 15001, Université Montpellier 2, F-34095 Montpellier (France); Guérin, Stéphane, E-mail: sguerin@u-bourgogne.fr [Département Optique, Interaction Matière-Rayonnement (OMR) (UMR 6303), Université de Bourgogne, F-21078 Dijon (France); Gatti, Fabien, E-mail: gatti@univ-montp2.fr [CTMM, Institut Charles Gerhardt Montpellier (UMR5253), CC 15001, Université Montpellier 2, F-34095 Montpellier (France)

    2014-10-17

    Highlights: • We perform quantum mechanical simulations for the ring-opening of benzopyran. • We develop strategies of control with laser pulses. • We focus on the physics involving the conical intersection. - Abstract: The ring-opening photoisomerization of benzopyran, which occurs via a photochemical route involving a conical intersection, has been studied with quantum dynamics calculations using the multi-configuration time-dependent Hartree method (MCTDH). We introduce a mechanistic strategy to control the conversion of benzopyran to merocyanine with laser pulses. We use a six-dimensional model developed in a previous work for the potential energy surfaces (PES) based on an extension of the vibronic-coupling Hamiltonian model (diabatization method by ansatz), which depends on the most active degrees of freedom. The main objective of these quantum dynamics simulations is to provide a set of strategies that could help experimentalists to control the photoreactivity vs. photostability ratio (selectivity). In this work we present: (i) a pump–dump technique used to control the photostability, (ii) a two-step strategy to enhance the reactivity of the system: first, a pure vibrational excitation in the electronic ground state that prepares the system and, second, an ultraviolet excitation that brings the system to the first adiabatic electronic state; (iii) finally the effect of a non-resonant pulse (Stark effect) on the dynamics.

  7. Effects of laser wavelength and fluence on the growth of ZnO thin films by pulsed laser deposition

    NARCIS (Netherlands)

    Craciun, V.; Amirhaghi, S.; Craciun, D.; Elders, J.; Gardeniers, Johannes G.E.; Boyd, Ian W.

    Transparent, electrically conductive and c-axis oriented ZnO thin films have been grown by the pulsed laser deposition (PLD) technique on silicon and Corning glass substrates employing either a KrF excimer laser (λ = 248 nm) or a frequency-doubled Nd:YAG laser (λ = 532 nm). The crystalline

  8. Measurement of weldpiece distortion during pulsed laser welding using rapid laser profilometry

    OpenAIRE

    Gorkič, Aleš; Jezeršek, Matija; Možina, Janez; Diaci, Janez

    2015-01-01

    The present paper reports a new setup for acquisition of shape data for weldpieces during pulsed laser welding. The setup is based on illumination of the weldpiece surface by laser light, which is structured as multiple light planes, and acquisition of the image of the illuminated surface by a digital camera. The position of the optical system is fixed relative to the measured weldpiece. The acquired image is fed into a personal computer where it is processed to obtain the three-dimensional s...

  9. Laser Ion Acceleration from the Interaction of Ultra-Intense laser Pulse with thi foils

    Energy Technology Data Exchange (ETDEWEB)

    Allen, Matthew Mark [Univ. of California, Berkeley, CA (United States)

    2004-03-12

    The discovery that ultra-intense laser pulses (I > 1018 W/cm2) can produce short pulse, high energy proton beams has renewed interest in the fundamental mechanisms that govern particle acceleration from laser-solid interactions. Experiments have shown that protons present as hydrocarbon contaminants on laser targets can be accelerated up to energies > 50 MeV. Different theoretical models that explain the observed results have been proposed. One model describes a front-surface acceleration mechanism based on the ponderomotive potential of the laser pulse. At high intensities (I > 1018 W/cm2), the quiver energy of an electron oscillating in the electric field of the laser pulse exceeds the electron rest mass, requiring the consideration of relativistic effects. The relativistically correct ponderomotive potential is given by Up = ([1 + Iλ2/1.3 x 1018]1/2 - 1) moc2, where Iλ2 is the irradiance in Wμm2/cm2 and moc2 is the electron rest mass.At laser irradiance of Iλ2 ~ 1018 Wμm2/cm2, the ponderomotive potential can be of order several MeV. A few recent experiments--discussed in Chapter 3 of this thesis--consider this ponderomotive potential sufficiently strong to accelerate protons from the front surface of the target to energies up to tens of MeV. Another model, known as Target Normal Sheath Acceleration (TNSA), describes the mechanism as an electrostatic sheath on the back surface of the laser target. According to the TNSA model, relativistic hot electrons created at the laser-solid interaction penetrate the foil where a few escape to infinity. The remaining hot electrons are retained by the target potential and establish an electrostatic sheath on the back surface of the target.

  10. Design and Applications of In-Cavity Pulse Shaping by Spectral Sculpturing in Mode-Locked Fibre Lasers

    Directory of Open Access Journals (Sweden)

    Sonia Boscolo

    2015-11-01

    Full Text Available We review our recent progress on the realisation of pulse shaping in passively-mode-locked fibre lasers by inclusion of an amplitude and/or phase spectral filter into the laser cavity. We numerically show that depending on the amplitude transfer function of the in-cavity filter, various regimes of advanced waveform generation can be achieved, including ones featuring parabolic-, flat-top- and triangular-profiled pulses. An application of this approach using a flat-top spectral filter is shown to achieve the direct generation of high-quality sinc-shaped optical Nyquist pulses with a widely tunable bandwidth from the laser oscillator. We also present the operation of an ultrafast fibre laser in which conventional soliton, dispersion-managed soliton (stretched-pulse and dissipative soliton mode-locking regimes can be selectively and reliably targeted by adaptively changing the dispersion profile and bandwidth programmed on an in-cavity programmable filter. The results demonstrate the strong potential of an in-cavity spectral pulse shaper for achieving a high degree of control over the dynamics and output of mode-locked fibre lasers.

  11. Effects of Nd:YAG laser pulse frequency on the surface treatment of Ti 6Al 4V alloys

    Energy Technology Data Exchange (ETDEWEB)

    Gursel, Ali [International University of Sarajevo (Bosnia and Herzegovina). Dept. of Mechanical Engineering

    2016-07-01

    The desirable properties of titanium and titanium alloys, including excellent corrosion resistance, high strength to weight ratio and high operating temperature, have led to their successful application in various fields such as the medical and aerospace industries. Among the reliable treatment techniques, laser welding can provide significant advantages for the titanium alloys because of its precision, rapid processing capability and ability to control the welding parameters and their effects. The morphology and the quality of pulsed seam welds are directly or synergistically influenced by the Nd:YAG laser parameters of pulse shape, energy, duration, travel speed, peak power and frequency of repetition. In this study, a 1.5 mm thick Ti-6Al-4V alloy sheet surface was treated by SigmaLaser {sup registered} 300 Nd:YAG pulsed laser. The influence of the pulse frequency on seam morphology and surface effects was then investigated. The seam and surface quality were characterized in terms of weld morphology and microhardness. The results showed that, for Nd:YAG laser seams used for surface treatment, pulse repetition was more effective on the cooling rate than had been expected.

  12. Controlling the spectral shape of nonlinear Thomson scattering with proper laser chirping

    Directory of Open Access Journals (Sweden)

    S. G. Rykovanov

    2016-03-01

    Full Text Available Effects of nonlinearity in Thomson scattering of a high intensity laser pulse from electrons are analyzed. Analytic expressions for laser pulse shaping in frequency (chirping are obtained which control spectrum broadening for high laser pulse intensities. These analytic solutions allow prediction of the spectral form and required laser parameters to avoid broadening. Results of analytical and numerical calculations agree well. The control over the scattered radiation bandwidth allows narrow bandwidth sources to be produced using high scattering intensities, which in turn greatly improves scattering yield for future x- and gamma-ray sources.

  13. Planar waveguide devices fabricated by pulsed laser deposition

    CERN Document Server

    Barrington, S J

    2001-01-01

    buried Nd:GGG waveguide laser has been fabricated for the first time by PLD and has achieved lasing action at a threshold of 14.8 mW of absorbed power. Comparison of the lasing threshold to that of similar uncapped devices demonstrate that the capped layer has a highly beneficial effect on the lasing threshold when the particulate density in the film is high. This thesis is intended to be a comprehensive study on using pulsed laser deposition to fabricate planar waveguide devices. As such a thorough review into the state of art of current activities in this area is initially presented. A versatile technique has been developed to efficiently and homogeneously heat substrates using a raster scanned CO sub 2 laser. Use of this device has virtually eliminated the occurrence of substrate fracture and has greatly reduced the turn-around time for depositions of crystalline films. The heating homogeneity achievable with this system is ultimately limited to speed at which it is able to scan the substrate. Growth of ph...

  14. Pulsed Laser Interactions with Space Debris: Target Shape Effects

    CERN Document Server

    Liedahl, D A; Libby, S B; Nikolaev, S; Phipps, C R

    2013-01-01

    Among the approaches to the proposed mitigation and remediation of the space debris problem is the de-orbiting of objects in low Earth orbit through irradiation by ground-based high-intensity pulsed lasers. Laser ablation of a thin surface layer causes target recoil, resulting in the depletion of orbital angular momentum and accelerated atmospheric re-entry. However, both the magnitude and direction of the recoil are shape dependent, a feature of the laser-based remediation concept that has received little attention. Since the development of a predictive capability is desirable, we have investigated the dynamical response to ablation of objects comprising a variety of shapes. We derive and demonstrate a simple analytical technique for calculating the ablation-driven transfer of linear momentum, emphasizing cases for which the recoil is not exclusively parallel to the incident beam. For the purposes of comparison and contrast, we examine one case of momentum transfer in the low-intensity regime, where photon p...

  15. Near-infrared laser-induced fluorescence detection in column liquid chromatography. A comparison of various lasers and detection systems. II*. Pulsed lasers.

    NARCIS (Netherlands)

    Mank, A.J.G.; Velthorst, N.H.; Brinkman, U.A.T.; Gooijer, C.

    1995-01-01

    The applicability of two pulsed lasers, a XeCl-excimer/dye laser and a Nd:YAG/dye laser combination, as excitation sources for near-infrared (NIR) laser-induced fluorescence (LIF) detection in column liquid chromatography (LC) is studied. Using gradient LC, the best detection limit for the model

  16. Laser-induced retinal damage threshold for repetitive-pulse exposure to 100-μs pulses

    Science.gov (United States)

    Lund, Brian J.; Lund, David J.; Edsall, Peter R.; Gaines, Victor D.

    2014-10-01

    The laser-induced retinal injury thresholds for repetitive-pulse exposures to 100-μs-duration pulses at a wavelength of 532 nm have been determined for exposures of up to 1000 pulses in an in vivo model. The ED50 was measured for pulse repetition frequencies of 50 and 1000 Hz. Exposures to collimated beams producing a minimal retinal beam spot and to divergent beams producing a 100-μm-diameter retinal beam spot were considered. The ED50 for a 100-μs exposure was measured to be 12.8 μJ total intraocular energy for a minimal retinal beam spot exposure and 18.1 μJ total intraocular energy for a 100-μm-diameter retinal beam spot. The threshold for exposures to N>1 pulse was found to be the same for both pulse repetition frequencies. The variation of the ED50 with the number of pulses is described well by the probability summation model, in which each pulse is considered an independent event. This is consistent with a threshold-level damage mechanism of microcavitation for single-pulse 100-μs-duration exposures. The data support the maximum permissible exposure levels for repetitive-pulse exposure promulgated in the most recent laser safety guidelines.

  17. Layered MoS{sub 2} grown on c-sapphire by pulsed laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Ho, Yen-Teng; Ma, Chun-Hao; Luong, Tien-Tung; Wei, Lin-Lung; Yen, Tzu-Chun; Chu, Yung-Ching; Tu, Yung-Yi [Department of Materials Science and Engineering, National Chiao Tung University, Hsinchu (China); Hsu, Wei-Ting; Chang, Wen-Hao [Department of Electrophysics, National Chiao Tung University, Hsinchu (China); Pande, Krishna Prasad [Department of Electrical and Computer Engineering, National Chiao Tung University, Hsinchu (China); Chang, Edward Yi [Department of Materials Science and Engineering, National Chiao Tung University, Hsinchu (China); Department of Electronics Engineering, National Chiao Tung University, Hsinchu (China)

    2015-03-01

    Layered growth of molybdenum disulphide (MoS{sub 2}) was successfully achieved by pulsed laser deposition (PLD) method on c -plane sapphire substrate. Growth of monolayer to a few monolayer MoS{sub 2}, dependent on the pulsed number of excimer laser in PLD is demonstrated, indicating the promising controllability of layer growth. Among the samples with various pulse number deposition, the frequency difference (A{sub 1g}-E{sup 1}{sub 2g}) in Raman analysis of the 70 pulse sample is estimated as 20.11 cm{sup -1}, suggesting a monolayer MoS{sub 2} was obtained. Two-dimensional (2D) layer growth of MoS{sub 2} is confirmed by the streaky reflection high energy electron diffraction (RHEED) patterns during growth and the cross-sectional view of transmission electron microscopy (TEM). The in-plane relationship, (0006) sapphire//(0002)MoS{sub 2} and [2 anti 1 anti 10] sapphire//[0 anti 1 anti 10]MoS{sub 2} is determined. The results imply that PLD is suitable for layered MoS{sub 2} growth. Additionally, the oxide states of Mo 3d core level spectra of PLD grown MoS{sub 2}, analysed by X-ray photoelectron spectroscopy (XPS), can be effectively reduced by adopting a post sulfurization process. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  18. Effect of double-pulse-laser polarization and time delay on laser-assisted etching of fused silica

    Science.gov (United States)

    Chu, Dongkai; Sun, Xiaoyan; Dong, Xinran; Yin, Kai; Luo, Zhi; Chen, Guowei; Duan, Ji-An; Hu, Youwang; Zhao, Xinyu

    2017-11-01

    High-aspect-ratio microchannels were fabricated by femtosecond-double-pulse-laser-assisted polarization-selective etching. The etching rate and uniformity of the microchannels were mainly determined by the double-pulse polarization and time delay. We found that when the two sub-pulses had a different polarization (one linear, the other circular), the microchannel etching rate increased by a factor of 10 compared to when both sub-pulses were linearly polarized. The maximum etching rate was obtained when the polarization combination was circular for the first sub-pulse and vertical for the second one. In this case, the etching rate was independent from the time delay. Laser confocal microscopy images showed that when the polarization was circular, the area modified by the laser was larger than when the polarization was linear, explaining the higher etching rate value obtained after irradiation with circularly polarized laser light.

  19. Optical emission spectra of ZnMnO plasma produced by a pulsed laser

    Science.gov (United States)

    Uzuriaga, J.; Chamorro, J. C.; Marín, R. A.; Riascos, H.

    2012-06-01

    Optical emission lines from the plasma generated by a laser ablation process have been investigated to gather information on the nature of the chemical species present. In particular, the experiments were carried out during the laser ablation of a ZnMnO target, in presence of a controlled oxygen atmosphere. The resolved emission spectra are dominated by the atomic neutral or singly ionized emission lines from Zn species, while the Mn I line was detected in emission spectrum at 40 mTorr only. The background continuum, intensities and widths of all observed lines increased with increasing gas pressure. The electron density and electron temperature were calculated for various gas pressures. The electron density was found to increase with the increment of the argon gas pressure, whereas electron temperature decreased. The electron temperature and density are found to be similar to those obtained in the well-known pulsed laser deposition (PLD) process.

  20. In vivo photoacoustic imaging of blood vessels with a pulsed laser diode

    NARCIS (Netherlands)

    Kolkman, R.G.M.; Steenbergen, Wiendelt; van Leeuwen, Ton

    2006-01-01

    Photoacoustic imaging is a hybrid imaging modality that is based on the detection of acoustic waves generated by absorption of pulsed light by tissue chromophores such as hemoglobin in blood. For this technique, usually large and costly Q-switched Nd:YAG lasers are used. These lasers provide a pulse