Linear Matrix Inequalities in Multirate Control over Networks

Directory of Open Access Journals (Sweden)

Ángel Cuenca

2012-01-01

Full Text Available This paper faces two of the main drawbacks in networked control systems: bandwidth constraints and timevarying delays. The bandwidth limitations are solved by using multirate control techniques. The resultant multirate controller must ensure closed-loop stability in the presence of time-varying delays. Some stability conditions and a state feedback controller design are formulated in terms of linear matrix inequalities. The theoretical proposal is validated in two different experimental environments: a crane-based test-bed over Ethernet, and a maglev based platform over Profibus.

Wave boundary layer over a stone-covered bed

DEFF Research Database (Denmark)

Dixen, Martin; Hatipoglu, Figen; Sumer, B. Mutlu

2008-01-01

This paper summarizes the results of an experimental investigation on wave boundary layers over a bed with large roughness, simulating stone/rock/armour block cover on the sea bottom. The roughness elements used in the experiments were stones the size of 1.4cm and 3.85cm in one group of experiments...

Carbon Bed Mercury Emissions Control For Mixed Waste Treatment

International Nuclear Information System (INIS)

Soelberg, Nick; Enneking, Joe

2010-01-01

Mercury has had various uses in nuclear fuel reprocessing and other nuclear processes, and so is often present in radioactive and mixed (both radioactive and hazardous according to the Resource Conservation and Recovery Act) wastes. Depending on regulatory requirements, the mercury in the off-gas must be controlled with sometimes very high efficiencies. Compliance to the Hazardous Waste Combustor (HWC) Maximum Achievable Control Technology (MACT) standards can require off-gas mercury removal efficiencies up to 99.999% for thermally treating some mixed waste streams. Several test programs have demonstrated this level of off-gas mercury control using fixed beds of granular sulfur-impregnated activated carbon. Other results of these tests include: (a) The depth of the mercury control mass transfer zone was less than 15-30 cm for the operating conditions of these tests, (b) MERSORB(reg s ign) carbon can sorb Hg up to 19 wt% of the carbon mass, and (c) the spent carbon retained almost all (98-99.99%) of the Hg; but when even a small fraction of the total Hg dissolves, the spent carbon can fail the TCLP test when the spent carbon contains high Hg concentrations. Localized areas in a carbon bed that become heated through heat of adsorption, to temperatures where oxidation occurs, are referred to as 'bed hot spots.' Carbon bed hot spots must be avoided in processes that treat radioactive and mixed waste. Key to carbon bed hot spot mitigation are (a) designing for sufficient gas velocity, for avoiding gas flow maldistribution, and for sufficient but not excessive bed depth, (b) monitoring and control of inlet gas flowrate, temperature, and composition, (c) monitoring and control of in-bed and bed outlet gas temperatures, and (d) most important, monitoring of bed outlet CO concentrations. An increase of CO levels in the off-gas downstream of the carbon bed to levels about 50-100 ppm higher than the inlet CO concentration indicate CO formation in the bed, caused by carbon bed

Specific and cross over effects of massage for muscle soreness: randomized controlled trial.

Science.gov (United States)

Jay, Kenneth; Sundstrup, Emil; Søndergaard, Stine D; Behm, David; Brandt, Mikkel; Særvoll, Charlotte A; Jakobsen, Markus D; Andersen, Lars L

2014-02-01

Muscle soreness can negatively interfere with the activities of daily living as well as sports performance. In the working environment, a common problem is muscle tenderness, soreness and pain, especially for workers frequently exposed to unilateral high repetitive movements tasks. The aim of the study is therefore to investigate the acute effect of massage applied using a simple device Thera-band roller Massager on laboratory induced hamstring muscle soreness, and the potential cross over effect to the non-massaged limb. 22 healthy untrained men (Mean age 34 +/- 7 years; mean height 181.7 +/- 6.9 cm; mean weight 80.6 +/- 6.4 kg; BMI: 24.5 +/- 1.3) with no prior history of knee, low back or neck injury or other adverse health issues were recruited. Participants visited the researchers on two separate occasions, separated by 48 hours, each time providing a soreness rating (modified visual analog scale 0-10), and being tested for pressure pain threshold (PPT) and active range of motion (ROM) of the hamstring muscles. During the first visit, delayed onset muscular soreness of the hamstring muscles was induced by 10 x 10 repetitions of the stiff-legged dead-lift. On the second visit participants received either 1) 10 minutes of roller massage on one leg, while the contralateral leg served as a cross over control, or 2) Resting for 10 minutes with no massage at all. Measurement of soreness, PPT and ROM were taken immediately before and at 0, 10, 30 and 60 min. after treatment. There was a significant group by time interaction for soreness (p < 0.0001) and PPT (p = 0.0007), with the massage group experiencing reduced soreness and increasing PPT compared with the control group. There was no group by time interaction for ROM (p = 0.18). At 10 min. post massage there was a significant reduction in soreness of the non-massaged limb in the cross over control group compared to controls but this effect was lost 30 minutes post massage. Massage with a roller device reduces

Near-Bed Turbulent Kinetic Energy Budget Under a Large-Scale Plunging Breaking Wave Over a Fixed Bar

Science.gov (United States)

van der Zanden, Joep; van der A, Dominic A.; Cáceres, Iván.; Hurther, David; McLelland, Stuart J.; Ribberink, Jan S.; O'Donoghue, Tom

2018-02-01

Hydrodynamics under regular plunging breaking waves over a fixed breaker bar were studied in a large-scale wave flume. A previous paper reported on the outer flow hydrodynamics; the present paper focuses on the turbulence dynamics near the bed (up to 0.10 m from the bed). Velocities were measured with high spatial and temporal resolution using a two component laser Doppler anemometer. The results show that even at close distance from the bed (1 mm), the turbulent kinetic energy (TKE) increases by a factor five between the shoaling, and breaking regions because of invasion of wave breaking turbulence. The sign and phase behavior of the time-dependent Reynolds shear stresses at elevations up to approximately 0.02 m from the bed (roughly twice the elevation of the boundary layer overshoot) are mainly controlled by local bed-shear-generated turbulence, but at higher elevations Reynolds stresses are controlled by wave breaking turbulence. The measurements are subsequently analyzed to investigate the TKE budget at wave-averaged and intrawave time scales. Horizontal and vertical turbulence advection, production, and dissipation are the major terms. A two-dimensional wave-averaged circulation drives advection of wave breaking turbulence through the near-bed layer, resulting in a net downward influx in the bar trough region, followed by seaward advection along the bar's shoreward slope, and an upward outflux above the bar crest. The strongly nonuniform flow across the bar combined with the presence of anisotropic turbulence enhances turbulent production rates near the bed.

Do-it-yourself Bed Bug Control

Science.gov (United States)

... Contact Us Share Do-it-yourself Bed Bug Control Información relacionada disponible en español Can you treat ... all of the residents to participate. Achieving complete control can take weeks to months, depending on the ...

A Pebble Bed Reactor cross section methodology

International Nuclear Information System (INIS)

Hudson, Nathanael H.; Ougouag, Abderrafi M.; Rahnema, Farzad; Gougar, Hans

2009-01-01

A method is presented for the evaluation of microscopic cross sections for the Pebble Bed Reactor (PBR) neutron diffusion computational models during convergence to an equilibrium (asymptotic) fuel cycle. This method considers the isotopics within a core spectral zone and the leakages from such a zone as they arise during reactor operation. The randomness of the spatial distribution of fuel grains within the fuel pebbles and that of the fuel and moderator pebbles within the core, the double heterogeneity of the fuel, and the indeterminate burnup of the spectral zones all pose a unique challenge for the computation of the local microscopic cross sections. As prior knowledge of the equilibrium composition and leakage is not available, it is necessary to repeatedly re-compute the group constants with updated zone information. A method is presented to account for local spectral zone composition and leakage effects without resorting to frequent spectrum code calls. Fine group data are pre-computed for a range of isotopic states. Microscopic cross sections and zone nuclide number densities are used to construct fine group macroscopic cross sections, which, together with fission spectra, flux modulation factors, and zone buckling, are used in the solution of the slowing down balance to generate a new or updated spectrum. The microscopic cross-sections are then re-collapsed with the new spectrum for the local spectral zone. This technique is named the Spectral History Correction (SHC) method. It is found that this method accurately recalculates local broad group microscopic cross sections. Significant improvement in the core eigenvalue, flux, and power peaking factor is observed when the local cross sections are corrected for the effects of the spectral zone composition and leakage in two-dimensional PBR test problems.

Synthetic bedding and wheeze in childhood.

Science.gov (United States)

Ponsonby, Anne-Louise; Dwyer, Terence; Kemp, Andrew; Cochrane, Jennifer; Couper, David; Carmichael, Allan

2003-01-01

The reasons for the increase in childhood asthma over time are unclear. The indoor environment is of particular concern. An adverse role for synthetic bedding on asthma development in childhood has been suggested by cross-sectional studies that have found an association between synthetic pillow use and childhood wheeze. Prospective data on infant bedding have not been available. Bedding data at 1 month of age were available from an infant survey for children who were participating in a 1995 follow-up study (N = 863; 78% traced). The 1995 follow-up was embedded in a larger cross-sectional survey involving 6,378 seven year olds in Tasmania (N = 92% of eligible). Outcome measures included respiratory symptoms as defined in the International Study of Asthma and Allergies in Childhood protocol. Frequent wheeze was defined as more than 12 wheeze episodes over the past year compared with no wheeze. Synthetic pillow use at 1 month of age was associated with frequent wheeze at age 7 (adjusted relative risk [aRR] = 2.5; 95% confidence interval [CI] = 1.2-5.5) independent of childhood exposure. Current synthetic pillow and quilt use was strongly associated with frequent wheeze (aRR = 5.2; CI = 1.3-20.6). Substantial trends were evident for an association of increasing number of synthetic bedding items with frequent wheeze and with increasing wheeze frequency. Among children with asthma, the age of onset of asthma occurred earlier if synthetic bedding was used in infancy. In this cohort, synthetic bedding was strongly and consistently associated with frequent childhood wheeze. The association did not appear to be attributable to bedding choice as part of an asthma management strategy.

The Importance of Splat Events to the Spatiotemporal Structure of Near-Bed Fluid Velocity and Bed Load Motion Over Bed Forms: Laboratory Experiments Downstream of a Backward Facing Step

Science.gov (United States)

Leary, K. C. P.; Schmeeckle, M. W.

2017-12-01

Flow separation/reattachment on the lee side of alluvial bed forms is known to produce a complex turbulence field, but the spatiotemporal details of the associated patterns of bed load sediment transported remain largely unknown. Here we report turbulence-resolving, simultaneous measurements of bed load motion and near-bed fluid velocity downstream of a backward facing step in a laboratory flume. Two synchronized high-speed video cameras simultaneously observed bed load motion and the motion of neutrally buoyant particles in a laser light sheet 6 mm above the bed at 250 frames/s downstream of a 3.8 cm backward facing step. Particle Imaging Velocimetry (PIV) and Acoustic Doppler Velocimetry (ADV) were used to characterize fluid turbulent patterns, while manual particle tracking techniques were used to characterize bed load transport. Octant analysis, conducted using ADV data, coupled with Markovian sequence probability analysis highlights differences in the flow near reattachment versus farther downstream. Near reattachment, three distinct flow patterns are apparent. Farther downstream we see the development of a dominant flow sequence. Localized, intermittent, high-magnitude transport events are more apparent near flow reattachment. These events are composed of streamwise and cross-stream fluxes of comparable magnitudes. Transport pattern and fluid velocity data are consistent with the existence of permeable "splat events," wherein a volume of fluid moves toward and impinges on the bed (sweep) causing a radial movement of fluid in all directions around the point of impingement (outward interaction). This is congruent with flow patterns, identified with octant analysis, proximal to flow reattachment.

A two dimensional model of undertow current over mud bed

International Nuclear Information System (INIS)

Mir Hammadul Azam; Abdul Aziz Ibrahim; Noraieni Hj, Mokhtar

1996-01-01

Coastal wave-current dynamics often causes severe erosion and this activity is more prominent within the surf zone. Turbulence generated by breaking wave is a complex phenomena and the degree of complexity increases to a higher degree when it happens over mud bed. A better understanding on wave and current is necessary to enrich the engineering hand to facilitate any coastal development work. Since physical model has certain deficiencies, such as high cost and scaling problem, the need for developing numerical models in such cases is significant. A time averaged two dimensional model has been developed to simulate the undertow over mud bed. A turbulent energy model also included which considers only the vertical variation of mixing length. Production of turbulent kinetic energy in the surf zone has been calculated from an hydraulic jump analogy. The result obtained shows an insignificant vertical variation of current. Further research is needed involving laboratory and field works to get sufficient data for comparing the model results

Model-free adaptive control of supercritical circulating fluidized-bed boilers

Science.gov (United States)

Cheng, George Shu-Xing; Mulkey, Steven L

2014-12-16

A novel 3-Input-3-Output (3.times.3) Fuel-Air Ratio Model-Free Adaptive (MFA) controller is introduced, which can effectively control key process variables including Bed Temperature, Excess O2, and Furnace Negative Pressure of combustion processes of advanced boilers. A novel 7-input-7-output (7.times.7) MFA control system is also described for controlling a combined 3-Input-3-Output (3.times.3) process of Boiler-Turbine-Generator (BTG) units and a 5.times.5 CFB combustion process of advanced boilers. Those boilers include Circulating Fluidized-Bed (CFB) Boilers and Once-Through Supercritical Circulating Fluidized-Bed (OTSC CFB) Boilers.

Propagation of a Strong Shock Over a Random Bed of Spherical Particles

Energy Technology Data Exchange (ETDEWEB)

Mehta, Y. [Univ. of Florida, Gainesville, FL (United States); Neal, C. [Univ. of Florida, Gainesville, FL (United States); Salari, K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Jackson, T. L. [Univ. of Florida, Gainesville, FL (United States); Balachandar, S. [Univ. of Florida, Gainesville, FL (United States); Thakur, S. [Univ. of Florida, Gainesville, FL (United States)

2017-04-11

Propagation of a strong shock through a bed of particles results in complex wave dynamics such as a reflected shock, a transmitted shock, and highly unsteady flow inside the particle bed. In this paper we present three-dimensional numerical simulations of shock propagation in air over a random bed of particles. We assume the flow is inviscid and governed by the Euler equations of gas dynamics. Simulations are carried out by varying the volume fraction of the particle bed at a fixed shock Mach number. We compute the unsteady inviscid streamwise and transverse drag coefficients as a function of time for each particle in the random bed as a function of volume fraction. We show that (i) there are significant variations in the peak drag for the particles in the bed, (ii) the mean peak drag as a function of streamwise distance through the bed decreases with a slope that increases as the volume fraction increases, and (iii) the deviation from the mean peak drag does not correlate with local volume fraction. We also present the local Mach number and pressure contours for the different volume fractions to explain the various observed complex physical mechanisms occurring during the shock-particle interactions. Since the shock interaction with the random bed of particles leads to transmitted and reflected waves, we compute the average flow properties to characterize the strength of the transmitted and reflected shock waves and quantify the energy dissipation inside the particle bed. Finally, to better understand the complex wave dynamics in a random bed, we consider a simpler approximation of a planar shock propagating in a duct with a sudden area change. We obtain Riemann solutions to this problem, which are used to compare with fully resolved numerical simulations.

HIV incidence in rural South Africa: comparison of estimates from longitudinal surveillance and cross-sectional cBED assay testing.

Directory of Open Access Journals (Sweden)

Till Bärnighausen

Full Text Available The BED IgG-Capture Enzyme Immunoassay (cBED assay, a test of recent HIV infection, has been used to estimate HIV incidence in cross-sectional HIV surveys. However, there has been concern that the assay overestimates HIV incidence to an unknown extent because it falsely classifies some individuals with non-recent HIV infections as recently infected. We used data from a longitudinal HIV surveillance in rural South Africa to measure the fraction of people with non-recent HIV infection who are falsely classified as recently HIV-infected by the cBED assay (the long-term false-positive ratio (FPR and compared cBED assay-based HIV incidence estimates to longitudinally measured HIV incidence.We measured the long-term FPR in individuals with two positive HIV tests (in the HIV surveillance, 2003-2006 more than 306 days apart (sample size n = 1,065. We implemented four different formulae to calculate HIV incidence using cBED assay testing (n = 11,755 and obtained confidence intervals (CIs by directly calculating the central 95(th percentile of incidence values. We observed 4,869 individuals over 7,685 person-years for longitudinal HIV incidence estimation. The long-term FPR was 0.0169 (95% CI 0.0100-0.0266. Using this FPR, the cross-sectional cBED-based HIV incidence estimates (per 100 people per year varied between 3.03 (95% CI 2.44-3.63 and 3.19 (95% CI 2.57-3.82, depending on the incidence formula. Using a long-term FPR of 0.0560 based on previous studies, HIV incidence estimates varied between 0.65 (95% CI 0.00-1.32 and 0.71 (95% CI 0.00-1.43. The longitudinally measured HIV incidence was 3.09 per 100 people per year (95% CI 2.69-3.52, after adjustment to the sex-age distribution of the sample used in cBED assay-based estimation.In a rural community in South Africa with high HIV prevalence, the long-term FPR of the cBED assay is substantially lower than previous estimates. The cBED assay performs well in HIV incidence estimation if the locally

KAJIAN TEKNIS-EKONOMIS ALAT PENGERING PATI SAGU MODEL CROSS FLOW VIBRO FLUIDIZED BED (Study on Technical-Economic of Sago Starch Dryer Model of Cross Flow Vibro Fluidized Bed

Directory of Open Access Journals (Sweden)

Abadi Jading

2015-02-01

Full Text Available The purpose of this research was to evaluate performance of vibro cross flow fluidized bed dryer using biomass fuel for drying sago starch. The phase of research were evaluation of dryer heated by a biomass stove using coconut shell as a fuel and observation of the drying temperature, moisture content, drying time, energy analysis, and drying effiviency, as well as calculation of its economic analysis. The dryer has dimension of 200x50x1500 cm for length, width, hight, respectively, and working capacity of 35kg/process. The results showed that biomass fuel consumption for drying sago starch for 7 hours was 12740,00 MJ (70 kg/process and electricity consumption for blower and vibrator was 37,80 MJ. Furthermore, the dryer reduced moisture content of sago starch from 42% (wb to 12% (wb with temperature in the vibrator chamber of 40-60 oC and relative humidity of 50%, as well as ambient temperature of 30 3C and drying efficiency of 46,02%. Economic analysis showed that the dryer had NPV of Rp. 16.002.858, BCR of 1,53, IRR of 35%, and PBP of 3,51 years. Keywords: Cross flow, vibro fluidized bed dryer, biomass stoves, sago starch, financial analysis   ABSTRAK Tujuan penelitian ini adalah melakukan pengujian terhadap alat pengering pati berbasis sagu model cross flow vibrofluidized bed bertenaga biomassa. Tahapan penelitian meliputi pengujian alat pengering menggunakan tungku biomassa berbahan bakar tempurung kelapa dengan melakukan pengamatan suhu selama pengeringan, penurunan kadar air, waktu pengeringan, kebutuhan energi, efisiensi pengering, dan analisis finansial. Konstruksi alat pengering pati sagu model vibro fluidized bed bertenaga biomassa berukuran panjang, lebar dan tinggi masing-masing (200x50x1500 cm, serta memiliki daya tampung atau kapasitas maksimum pati sagu basah 35 kg/proses. Hasil pengujian menunjukkan bahwa alat pengering ini mampu mengeringkan pati sagu selama 7 jam, dengan konsumsi bahan bakar tempurung kelapa sebanyak 70 kg

Fluidization quality analyzer for fluidized beds

Science.gov (United States)

Daw, C.S.; Hawk, J.A.

1995-07-25

A control loop and fluidization quality analyzer for a fluidized bed utilizes time varying pressure drop measurements. A fast-response pressure transducer measures the overall bed pressure drop, or over some segment of the bed, and the pressure drop signal is processed to produce an output voltage which changes with the degree of fluidization turbulence. 9 figs.

The Role of Infragravity Waves in Near-Bed Cross-Shore Sediment Flux in the Breaker Zone

Directory of Open Access Journals (Sweden)

Samantha Kularatne

2014-08-01

Full Text Available Results from a series of field experiments, conducted to investigate the influence of infragravity waves (from wave groups, ripple type and location relative to the breaker line on cross-shore suspended sediment flux close to the sea bed in nearshore environments, are presented. The field data were collected from Cable Beach (Broome and Mullaloo Beach in Western Australia and Chilaw in Sri Lanka. These beaches experience different incident wave, tidal and morphological conditions, with Cable Beach having a 10-m spring tidal range, whilst the other two beaches have tidal ranges <1.0 m. Measurements included simultaneous records of surface elevation, two-dimensional horizontal current velocities and suspended sediment concentrations, together with half-hourly observations of the seabed topography. Although most of the data sets were obtained just outside of the surf zone, a few results from inside of the surf zone were also included. A significant correlation between wave groups and suspended sediment concentration was found at all of the measurement sites, either with or without bed ripples. The direction and magnitude of cross-shore suspended sediment flux varied with location with respect to the breaker line; however, other parameters, such as bed ripples and velocity skewness, could have influenced this result. In Broome, where the measurement location with respect to the breaker line varied with the tidal cycle, the cross-shore sediment flux due to swell waves was shoreward inside and just outside of the surf zone and seaward farther offshore of the breaker line. Further, sediment flux due to swell waves was onshore when the seabed was flat and offshore over post-vortex ripples. Sediment flux due to swell waves was onshore when the normalised velocity skewness towards the shore was high (positive; the flux was offshore when the skewness was lower, but positive, suggesting the influence of other parameters, such as ripples and grain size. The

Set-shifting abilities, mood and loss of control over eating in binge eating disorder: An experimental study.

Science.gov (United States)

Dingemans, Alexandra E; Visser, Hiske; Paul, Linda; van Furth, Eric F

2015-12-15

Executive functions play an important role in problem-solving and self-control. Set-shifting is an aspect of executive functioning and represents cognitive flexibility. The inability to control eating in Binge Eating Disorder (BED) may imply deficits in set-shifting which could be exacerbated by negative mood and depressive symptoms. The aim of the study was to test whether there is a causal relationship between set-shifting ability, changes in mood and loss of control over eating in BED. Seventy-five participants diagnosed with BED were randomly assigned to a negative or neutral mood induction. Set-shifting abilities, depressive symptoms, current mood and loss of control over eating were assessed. Having depressive symptoms and poorer set-shifting abilities resulted in a more negative mood after a negative mood induction, whereas this was not observed in the neutral mood induction. Post-hoc analyses revealed that individuals with poorer set-shifting abilities and more changes in negative mood, experienced more feelings of loss of control over eating than individuals whose set-shifting abilities were better and whose mood did not change. The results suggest that both depressive symptoms and deficits in set-shifting abilities may decrease an individual's ability to handle negative affect and increase loss of control over eating in individuals with BED. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Gabapentin in traumatic nerve injury pain: A randomized, double-blind, placebo-controlled, cross-over, multi-center study

DEFF Research Database (Denmark)

Gordh, Torsten E; Stubhaug, Audun; Jensen, Troels S

2008-01-01

A double-blind, randomized, placebo-controlled cross-over multi-center study was conducted to evaluate the efficacy and safety of gabapentin in the treatment of neuropathic pain caused by traumatic or postsurgical peripheral nerve injury, using doses up to 2400mg/day. The study comprised a run...

Coordinated Control of Cross-Flow Turbines

Science.gov (United States)

Strom, Benjamin; Brunton, Steven; Polagye, Brian

2016-11-01

Cross-flow turbines, also known as vertical-axis turbines, have several advantages over axial-flow turbines for a number of applications including urban wind power, high-density arrays, and marine or fluvial currents. By controlling the angular velocity applied to the turbine as a function of angular blade position, we have demonstrated a 79 percent increase in cross-flow turbine efficiency over constant-velocity control. This strategy uses the downhill simplex method to optimize control parameter profiles during operation of a model turbine in a recirculating water flume. This optimization method is extended to a set of two turbines, where the blade motions and position of the downstream turbine are optimized to beneficially interact with the coherent structures in the wake of the upstream turbine. This control scheme has the potential to enable high-density arrays of cross-flow turbines to operate at cost-effective efficiency. Turbine wake and force measurements are analyzed for insight into the effect of a coordinated control strategy.

Implications of Lessons Learned From Tobacco Control for Tanning Bed Reform

Science.gov (United States)

Sinclair, Craig

2013-01-01

Tanning beds used according to the manufacturer’s instructions expose the user to health risks, including melanoma and other skin cancers. Applying the MPOWER model (monitor, protect, offer alternatives, warn, enforce, and raise taxes), which has been used in tobacco control, to tanning bed reform could reduce the number of people at risk of diseases associated with tanning bed use. Among the tactics available to government are restricting the use of tanning beds by people under age 18 and those with fair skin, increasing the price of tanning bed services through taxation, licensing tanning bed operators, and banning unsupervised tanning bed operations. PMID:23449282

Exploring Parental Bonding in BED and Non-BED Obesity Compared with Healthy Controls: Clinical, Personality and Psychopathology Correlates.

Science.gov (United States)

Amianto, Federico; Ercole, Roberta; Abbate Daga, Giovanni; Fassino, Secondo

2016-05-01

Early inadequate attachment experiences are relevant co-factors in the development of obesity and Binge Eating Disorder (BED), which often concurs with obesity. The relationship of parental bonding with personality and psychopathology may influence treatment strategies for obese subjects, either affected or not with BED. In this study, 443 obese women (BMI ≥ 30 kg/m(2)), including 243 with and 200 without BED, and 158 female controls were assessed with regards to attachment, personality and eating psychopathology measures. Clusters obtained using the scores of the Parental Bonding Instrument (PBI) were compared with each other and with a control subjects' group. Lower scores of parental bonding distinguished obese subjects with respect to healthy controls. The cluster analysis revealed two clusters of parenting among obese subjects. The larger one displayed intermediate care and overprotection between controls and the smaller cluster, with the exception of paternal overprotection which is similar to controls. This larger cluster was characterized by low persistence and levels of psychopathology which are intermediate between healthy controls and the smaller cluster. The smaller cluster displayed lower care and higher overcontrol from both parents. It also displays more extreme personality traits (high novelty seeking and harm avoidance, and lower self-directedness and cooperativeness) and more severe eating and general psychopathology. Different parenting dynamics relate to different personality patterns and eating psychopathology of obese subjects, but not to binge eating conducts. Personality differences between parenting clusters are more extensive than those between BED and non-BED subgroups. The two different typologies of obese subjects based on parenting may be relevant for treatment personalization. Copyright © 2015 John Wiley & Sons, Ltd and Eating Disorders Association.

Granular controls on the dispersion of bed load tracers

Science.gov (United States)

Jerolmack, D. J.; Martin, R. L.; Phillips, C. B.

2014-12-01

Coarse particles are transported in a river as bed load, i.e., they move in frequent contact with and are supported by the granular bed. This movement is typically intermittent and may be described by a series of steps are rests, the distributions of which determine particle dispersion. Laboratory and field studies of bed load tracer dispersion have reported sub- and super-diffusive behavior, both of which have been successfully reproduced with stochastic transport models. Although researchers have invoked heavy-tailed step lengths as the cause of anomalous dispersion, most observations report thin-tailed distributions. Little attention has been paid to rest periods, and stochastic transport models have not been connected to the underlying mechanics of particle motion. Based on theoretical and experimental evidence, we argue that step lengths are thin-tailed and do not control the longterm dispersion of bed load tracers; they are determined by momentum balance between the fluid and solid. Using laboratory experiments with both marbles and natural sediments, we demonstrate that the rest time distribution is power law, and argue that this distribution controls asymptotic dispersion. Observed rest times far exceed any hydrodynamic timescale. Experiments reveal that rest times of deposited particles are governed by fluctuations in river bed elevation; in particular, the return time for the bed to scour to the base of a deposited particle. Stochastic fluctuations in bed elevation are describable by an Ornstein-Uhlenbeck (mean-reverting random walk) model that contains two parameters, which we show are directly related to the granular shear rate and range of bed elevation fluctuations, respectively. Combining these results with the theory of asymmetric random walks (particles only move downstream), we predict superdiffusive behavior that is in quantitative agreement with our observations of tracer dispersion in a natural river.

Bed Utilisation in an Irish Regional Paediatric Unit A Cross-Sectional Study Using the Paediatric Appropriateness Evaluation Protocol (PAEP)

LENUS (Irish Health Repository)

Ó hAiseadha, Coilín

2016-05-01

Increasing demand for limited healthcare resources raises questions about appropriate use of inpatient beds. In the first paediatric bed utilisation study at a regional university centre in Ireland, we conducted a cross-sectional study to audit the utilisation of inpatient beds at the Regional Paediatric Unit (RPU) in University Hospital Limerick (UHL), Limerick, Ireland and also examined hospital activity data, to make recommendations for optimal use of inpatient resources.

Effect of almond consumption on vascular function in patients with coronary artery disease: a randomized, controlled, cross-over trial

Science.gov (United States)

Objective: Almonds reduce cardiovascular disease risk via cholesterol reduction, anti-inflammation, glucoregulation, and antioxidation. The objective of this randomized, controlled, cross-over trial was to determine whether the addition of 85 g almonds daily to a National Cholesterol Education Progr...

The Cross-Flow Mixing Analysis of Quasi-Static Pebble Flow in Pebble Bed Reactor

International Nuclear Information System (INIS)

Fang Xiang; Liu Zhiyong; Sun Yanfei; Yang Xingtuan; Jiang Shengyao

2014-01-01

In the pebble bed reactor, large number of fuel pebbles’ movement law and moving state can affect the reactor’s design, operation and safety directly. Therefore the pebble flow, which is based on the theory of particle streaming, is one of the most important research subjects of the pebble bed reactor engineering. The in-core pebble flow is a very slow particle flow (or called quasi-static particle flow), which is very different from the usual particle motion. How to accurately describe the characteristics of in-core pebble flow is a central issue for this subject. Due to the presence of random flow, the cross-mixing phenomenon will occur inevitably. In the present paper, the mixing phenomenon of pebble flow is generalized on the basis of experiment results. The pebble flow cross-mixing probability serves as the parameter which describes both the regularity and the randomness of pebble flow. The results are provided in the form of diagrammatic presentation. (author)

Spatial variability of the wave bottom boundary layer over movable rippled beds

NARCIS (Netherlands)

Rodriguez-Abudo, S.; Foster, D.L.; Henriquez, M.

2013-01-01

Observations of the spatially dependent velocity field over movable bed forms subjected to slightly skewed and asymmetric regular wave forcing were collected. The dynamics between the ripple elements is dominated by coherent vortices, characterized by the swirling strength, and evidenced in the

Biofilm Effect on Flow Structure over a Permeable Bed

Science.gov (United States)

Kazemifar, F.; Blois, G.; Aybar, M.; Perez-Calleja, P.; Nerenberg, R.; Sinha, S.; Hardy, R. J.; Best, J.; Sambrook Smith, G.; Christensen, K. T.

2017-12-01

Biofilms constitute an important form of bacterial life in aquatic environments and are present at the fluid-solid interfaces in natural and industrial settings, such as water distribution systems and riverbeds among others. The permeable, heterogeneous, and deformable structure of biofilms can influence mass and momentum transport between the subsurface and freestream. However, this interaction is not fully understood, in part due to technical obstacles impeding quantitative experimental investigations. In this work, the effect of biofilm on flow structure over a permeable bed is studied. Experiments are conducted in a closed water channel equipped with an idealized two-dimensional permeable bed. Prior to conducting flow experiments, the models are placed within an independent recirculating reactor for biofilm growth. Once a targeted biofilm growth stage is achieved, the models are transferred to the water channel and subjected to transitional and turbulent flows. Long-distance microscopic particle image velocimetry measurements are performed to quantify the effect of biofilm on the turbulence structure of the free flow as well as the freestream-subsurface flow interaction.

Bed erosion control at 60 degree river confluence using vanes

Science.gov (United States)

Wuppukondur, Ananth; Chandra, Venu

2017-04-01

Confluences are common occurrences along natural rivers. Hydrodynamics at the confluence is complex due to merging of main and lateral flows with different characteristics. Bed erosion occurs at the confluence due to turbulence and also secondary circulation induced by centrifugal action of the lateral flow. The eroded sediment poses various problems in the river ecosystem including river bank failure. Reservoirs are majorly affected due to sediment deposition which reduces storage capacity. The bed erosion also endangers stability of pipeline crossings and bridge piers. The aim of this experimental study is to check the performance of vanes in controlling bed erosion at the confluence. Experiments are performed in a 600 confluence mobile bed model with a non-uniform sediment of mean particle size d50 = 0.28mm. Discharge ratio (q=ratio of lateral flow discharge to main flow discharge) is maintained as 0.5 and 0.75 with a constant average main flow depth (h) of 5cm. Vanes of width 0.3h (1.5cm) and thickness of 1 mm are placed along the mixing layer at an angle of 150, 300 and 600(with respect to main flow) to perform the experiments. Also, two different spacing of 2h and 3h (10cm and 15cm) between the vanes are used for conducting the experiments. A digital point gauge with an accuracy of ±0.1mm is used to measure bed levels and flow depths at the confluence. An Acoustic Doppler Velocitimeter (ADV) with a frequency of 25Hz and accuracy of ±1mm/s is used to measure flow velocities. Maximum scour depth ratio Rmax, which is ratio between maximum scour depth (Ds) and flow depth (h), is used to present the experimental results.From the experiments without vanes, it is observed that the velocities are increasing along the mixing layer and Rmax=0.82 and 1.06, for q=0.5 and 0.75, respectively. The velocities reduce with vanes since roughness increases along the mixing layer. For q=0.5 and 0.75, Rmax reduces to 0.62 and 0.7 with vanes at 2h spacing, respectively. Similarly

Direct Synthesis of Renewable Dodecanol and Dodecane with Methyl Isobutyl Ketone over Dual-Bed Catalyst Systems.

Science.gov (United States)

Sheng, Xueru; Li, Ning; Li, Guangyi; Wang, Wentao; Wang, Aiqin; Cong, Yu; Wang, Xiaodong; Zhang, Tao

2017-03-09

For the first time, we demonstrated two integrated processes for the direct synthesis of dodecanol or 2,4,8-trimethylnonane (a jet fuel range C 12 -branched alkane) using methyl isobutyl ketone (MIBK) that can be derived from lignocellulose. The reactions were carried out in dual-bed continuous flow reactors. In the first bed, MIBK was selectively converted to a mixture of C 12 alcohol and ketone. Over the Pd-modified magnesium- aluminium hydrotalcite (Pd-MgAl-HT) catalyst, a high total carbon yield (73.0 %) of C 12 oxygenates can be achieved under mild conditions. In the second bed, the C 12 oxygenates generated in the first bed were hydrogenated to dodecanol over a Ru/C catalyst or hydrodeoxygenated to 2,4,8-trimethylnonane over a Cu/SiO 2 catalyst. The as-obtained dodecanol can be used as feedstock in the production of sodium dodecylsulfate (SDS) and sodium dodecyl benzene sulfonate (SDBS), which are widely used as surfactants or detergents. The asobtained 2,4,8-trimethylnonane can be blended into conventional jet fuel without hydroisomerization. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Mounted Smartphones as Measurement and Control Platforms for Motor-Based Laboratory Test-Beds

Directory of Open Access Journals (Sweden)

Jared A. Frank

2016-08-01

Full Text Available Laboratory education in science and engineering often entails the use of test-beds equipped with costly peripherals for sensing, acquisition, storage, processing, and control of physical behavior. However, costly peripherals are no longer necessary to obtain precise measurements and achieve stable feedback control of test-beds. With smartphones performing diverse sensing and processing tasks, this study examines the feasibility of mounting smartphones directly to test-beds to exploit their embedded hardware and software in the measurement and control of the test-beds. This approach is a first step towards replacing laboratory-grade peripherals with more compact and affordable smartphone-based platforms, whose interactive user interfaces can engender wider participation and engagement from learners. Demonstrative cases are presented in which the sensing, computation, control, and user interaction with three motor-based test-beds are handled by a mounted smartphone. Results of experiments and simulations are used to validate the feasibility of mounted smartphones as measurement and feedback control platforms for motor-based laboratory test-beds, report the measurement precision and closed-loop performance achieved with such platforms, and address challenges in the development of platforms to maintain system stability.

Mounted Smartphones as Measurement and Control Platforms for Motor-Based Laboratory Test-Beds.

Science.gov (United States)

Frank, Jared A; Brill, Anthony; Kapila, Vikram

2016-08-20

Laboratory education in science and engineering often entails the use of test-beds equipped with costly peripherals for sensing, acquisition, storage, processing, and control of physical behavior. However, costly peripherals are no longer necessary to obtain precise measurements and achieve stable feedback control of test-beds. With smartphones performing diverse sensing and processing tasks, this study examines the feasibility of mounting smartphones directly to test-beds to exploit their embedded hardware and software in the measurement and control of the test-beds. This approach is a first step towards replacing laboratory-grade peripherals with more compact and affordable smartphone-based platforms, whose interactive user interfaces can engender wider participation and engagement from learners. Demonstrative cases are presented in which the sensing, computation, control, and user interaction with three motor-based test-beds are handled by a mounted smartphone. Results of experiments and simulations are used to validate the feasibility of mounted smartphones as measurement and feedback control platforms for motor-based laboratory test-beds, report the measurement precision and closed-loop performance achieved with such platforms, and address challenges in the development of platforms to maintain system stability.

The effect of levetiracetam on focal nocturnal epileptiform activity during sleep--a placebo-controlled double-blind cross-over study.

Science.gov (United States)

Larsson, Pål Gunnar; Bakke, Kristin A; Bjørnæs, Helge; Heminghyt, Einar; Rytter, Elisif; Brager-Larsen, Line; Eriksson, Ann-Sofie

2012-05-01

Electric Status Epilepticus during Sleep (ESES) occurs in children with and without epilepsy. It may be related to disturbances as autism spectrum disorder, attention-deficit hyperactivity disorder and acquired aphasia (Landau-Kleffner syndrome). Antiepileptic drug (AED) treatment has been reported in small studies without placebo control. This study was designed to assess AED effect in a placebo-controlled double-blind cross-over study. Levetiracetam (LEV) was chosen based on clinical evidence. Eighteen patients fulfilled the inclusion criteria. The mean spike index at baseline was 56, falling to a mean of 37 at the end of the LEV treatment period. Assessed with a 2-way ANOVA, there is a significant treatment effect (pdouble-blind cross-over study for any AED in patients with ESES. The effect of LEV is comparable with its effect in treatment of epileptic seizures. Copyright © 2012 Elsevier Inc. All rights reserved.

Genetic control of mitotic crossing over in yeast. 2. Influence of UV irradiation

International Nuclear Information System (INIS)

Zakharov, I.A.; Marfin, S.V.; Koval'tsova, S.V.; Kasinova, G.V.

1982-01-01

UV-induced crossing-over and general mitotic segregation of the following strains of Saccharomyces cerevisiae yeasts were studied: a wild-type diploid, diploids homozygous with respect to the radiosensitivity of rad 2, rad 15, rad 54, xrs 4, rad 2 rad 54, rad 15 rad 54. Wild-type diploids rad 2 and rad 15 have a high frequency of the induced mitotic crossing-over. Diploids rad 15, rad 54 can not cause UV-induced mitotic crossing-over. Reddish-pink and reddish-pink-white colonies ratio (the first appear if the crossing-over occurs during the first after the irradiation division, the second - during the second division) is 4.8:1 for the wild type, 1.6:1 for rad 2, and 1.1:1 for rad 15. Nonreciprocal mitotic segregation of high frequency was observed for the wild type rad 2, rad 15, xrs 4, and diploids rad 54, rad 2 rad 54, rad 15 rad 54 had a lower frequency. We suppose that after UV-irradiation there exist at least three types of repair in yeast diploid cells: excision repair, prereplication recombinating repair after the excision of dimers, and post-replication recombinating repair. Rad 2 and rad 15 mutations blow the first and second types, rad 54 mutation partially block the second and third parths. It seems that xrs 4 mutation does not block the recombinating capability but somehow changes the process of recombination in such a way that much nonreciprocal products recorded as seqregants are produced [ru

Implications of Lessons Learned From Tobacco Control for Tanning Bed Reform

OpenAIRE

Sinclair, Craig; Makin, Jennifer K.

2013-01-01

Tanning beds used according to the manufacturer?s instructions expose the user to health risks, including melanoma and other skin cancers. Applying the MPOWER model (monitor, protect, offer alternatives, warn, enforce, and raise taxes), which has been used in tobacco control, to tanning bed reform could reduce the number of people at risk of diseases associated with tanning bed use. Among the tactics available to government are restricting the use of tanning beds by people under age 18 and th...

2D numerical model of particle-bed collision in fluid-particle flows over bed

Czech Academy of Sciences Publication Activity Database

Lukerchenko, Nikolay; Chára, Zdeněk; Vlasák, Pavel

2006-01-01

Roč. 44, č. 1 (2006), s. 70-78 ISSN 0022-1686 R&D Projects: GA AV ČR IAA2060201 Institutional research plan: CEZ:AV0Z20600510 Keywords : saltation * particle-bed collision * collision angle * bed roughness Subject RIV: BK - Fluid Dynamics Impact factor: 0.527, year: 2006

Mounted Smartphones as Measurement and Control Platforms for Motor-Based Laboratory Test-Beds

OpenAIRE

Jared A. Frank; Anthony Brill; Vikram Kapila

2016-01-01

Laboratory education in science and engineering often entails the use of test-beds equipped with costly peripherals for sensing, acquisition, storage, processing, and control of physical behavior. However, costly peripherals are no longer necessary to obtain precise measurements and achieve stable feedback control of test-beds. With smartphones performing diverse sensing and processing tasks, this study examines the feasibility of mounting smartphones directly to test-beds to exploit their em...

Impaired prefrontal cognitive control over interference by food images in binge-eating disorder and bulimia nervosa.

Science.gov (United States)

Lee, Jung Eun; Namkoong, Kee; Jung, Young-Chul

2017-06-09

Binge-eating disorder (BED)characterized by recurrent episodes of binge-eating without inappropriate compensatory behaviors is classified as an official diagnosis in DSM-5. However, the neural bases that differentiate BED from other eating disorders such as bulimia nervosa (BN), are still under debate. Thirty-nine participants (HC, n=14; BN, n=13; BED, n=12) underwent functional MRI while performing a Stroop-Match-to-Sample task. This pilot study investigated how food images interfered with the behavioral performances and blood-oxygenation-level-dependent neuronal activity. Compared to healthy controls, participants with BN showed lower accuracy indicating impaired cognitive control over interference. Compared to healthy controls, participants with BED demonstrated stronger activations in the ventral striatum in response to food images. By contrast, participants with BN exhibited stronger activations in the premotor cortex and dorsal striatum. These aberrant ventral and dorsal frontostriatal activations in response to food images are associated with increased reward sensitivity and habitual binge-eating/purging behaviors in BED and BN. Copyright © 2017 Elsevier B.V. All rights reserved.

Mounted Smartphones as Measurement and Control Platforms for Motor-Based Laboratory Test-Beds †

Science.gov (United States)

Frank, Jared A.; Brill, Anthony; Kapila, Vikram

2016-01-01

Laboratory education in science and engineering often entails the use of test-beds equipped with costly peripherals for sensing, acquisition, storage, processing, and control of physical behavior. However, costly peripherals are no longer necessary to obtain precise measurements and achieve stable feedback control of test-beds. With smartphones performing diverse sensing and processing tasks, this study examines the feasibility of mounting smartphones directly to test-beds to exploit their embedded hardware and software in the measurement and control of the test-beds. This approach is a first step towards replacing laboratory-grade peripherals with more compact and affordable smartphone-based platforms, whose interactive user interfaces can engender wider participation and engagement from learners. Demonstrative cases are presented in which the sensing, computation, control, and user interaction with three motor-based test-beds are handled by a mounted smartphone. Results of experiments and simulations are used to validate the feasibility of mounted smartphones as measurement and feedback control platforms for motor-based laboratory test-beds, report the measurement precision and closed-loop performance achieved with such platforms, and address challenges in the development of platforms to maintain system stability. PMID:27556464

Prevention and Control of Bed Bugs in Residences

Science.gov (United States)

... in other rooms, including bathrooms, living rooms and laundry rooms. Look for spots or smears Dark blood ... having the inspection done by a pest control service provider (exterminator). If you find a bed bug, ...

Real time test bed development for power system operation, control and cyber security

Science.gov (United States)

Reddi, Ram Mohan

The operation and control of the power system in an efficient way is important in order to keep the system secure, reliable and economical. With advancements in smart grid, several new algorithms have been developed for improved operation and control. These algorithms need to be extensively tested and validated in real time before applying to the real electric power grid. This work focuses on the development of a real time test bed for testing and validating power system control algorithms, hardware devices and cyber security vulnerability. The test bed developed utilizes several hardware components including relays, phasor measurement units, phasor data concentrator, programmable logic controllers and several software tools. Current work also integrates historian for power system monitoring and data archiving. Finally, two different power system test cases are simulated to demonstrate the applications of developed test bed. The developed test bed can also be used for power system education.

An Apparatus for Bed Material Sediment Extraction From Coarse River Beds in Large Alluvial Rivers

Science.gov (United States)

Singer, M. B.; Adam, H.; Cooper, J.; Cepello, S.

2005-12-01

Grain size distributions of bed material sediment in large alluvial rivers are required in applications ranging from habitat mapping, calibration of sediment transport models, high resolution sediment routing, and testing of existing theories of longitudinal and cross steam sediment sorting. However, characterizing bed material sediment from coarse river beds is hampered by difficulties in sediment extraction, a challenge that is generally circumvented via pebble counts on point bars, even though it is unclear whether the bulk grain size distribution of bed sediments is well represented by pebble counts on bars. We have developed and tested a boat-based sampling apparatus and methodology for extracting bulk sediment from a wide range of riverbed materials. It involves the use of a 0.4 x 0.4 x 0.2 meter stainless steel toothed sampler, called the Cooper Scooper, which is deployed from and dragged downstream by the weight of a jet boat. The design is based on that of a river anchor such that a rotating center bar connected to a rope line in the boat aligns the sampler in the downstream direction, the teeth penetrate the bed surface, and the sampler digs into the bed. The sampler is fitted with lead weights to keep it from tipping over. The force of the sampler `biting' into the bed can be felt on the rope line held by a person in the boat at which point they let out slack. The boat then motors to the spot above the embedded sampler, which is hoisted to the water surface via a system of pulleys. The Cooper Scooper is then clipped into a winch and boom assembly by which it is brought aboard. This apparatus improves upon commonly used clamshell dredge samplers, which are unable to penetrate coarse or mixed bed surfaces. The Cooper Scooper, by contrast, extracts statistically representative bed material sediment samples of up to 30 kilograms. Not surprisingly, the sampler does not perform well in very coarse or armored beds (e.g. where surface material size is on the

Comparative analysis of several sediment transport formulations applied to dam-break flows over erodible beds

Science.gov (United States)

Cea, Luis; Bladé, Ernest; Corestein, Georgina; Fraga, Ignacio; Espinal, Marc; Puertas, Jerónimo

2014-05-01

Transitory flows generated by dam failures have a great sediment transport capacity, which induces important morphological changes on the river topography. Several studies have been published regarding the coupling between the sediment transport and hydrodynamic equations in dam-break applications, in order to correctly model their mutual interaction. Most of these models solve the depth-averaged shallow water equations to compute the water depth and velocity. On the other hand, a wide variety of sediment transport formulations have been arbitrarily used to compute the topography evolution. These are based on semi-empirical equations which have been calibrated under stationary and uniform conditions very different from those achieved in dam-break flows. Soares-Frazao et al. (2012) proposed a Benchmark test consisting of a dam-break over a mobile bed, in which several teams of modellers participated using different numerical models, and concluded that the key issue which still needs to be investigated in morphological modelling of dam-break flows is the link between the solid transport and the hydrodynamic variables. This paper presents a comparative analysis of different sediment transport formulations applied to dam-break flows over mobile beds. All the formulations analysed are commonly used in morphological studies in rivers, and include the formulas of Meyer-Peter & Müller (1948), Wong-Parker (2003), Einstein-Brown (1950), van Rijn (1984), Engelund-Hansen (1967), Ackers-White (1973), Yang (1973), and a Meyer-Peter & Müller type formula but with ad-hoc coefficients. The relevance of corrections on the sediment flux direction and magnitude due to the bed slope and the non-equilibrium hypothesis is also analysed. All the formulations have been implemented in the numerical model Iber (Bladé et al. (2014)), which solves the depth-averaged shallow water equations coupled to the Exner equation to evaluate the bed evolution. Two different test cases have been

Gas pipeline crossings over water bodies: analysis of environmental impact mitigation coming from controls adopted; Implantacao de travessias de gasodutos em corpos d'agua: analise da mitigacao dos impactos ambientais decorrente das medidas de controle adotadas

Energy Technology Data Exchange (ETDEWEB)

Serricchio, Claudio; Caldas, Flaviana V. [PETROBRAS, Rio de Janeiro, RJ (Brazil); Souza, Izabel C. de [TELSAN Engenharia e Servicos Ltda, Vitoria, ES (Brazil); Paz, Claudio [IMC Saste - Construcoes, Servicos e Comercio Ltda., Sao Paulo, SP (Brazil); Veronez, Fernanda A. [Centro Federal de Educacao Tecnologica do Espirito Santo (CEFET-ES), Vitoria, ES (Brazil)

2008-07-01

Among the implemented measures to control environmental impacts during the crossings of water courses, can be mentioned: the laying of pipe under provisional passages, the execution of physical barriers, the provisional and definitive drainage systems, the riverbank water bodies revegetation after the completion of works and the monitoring of water quality in the previous phases and after the execution of works for the implementation of the crossing. This study examined the effectiveness of these measures using as a case study the works of gas pipelines: Cacimbas (ES) - Vitoria (ES) and Cabiunas (RJ) - Vitoria (ES). In general it was observed that the measures taken were effective. In the case of implemented crossings with the conventional method of monitoring, the results confirmed an expected temporary increase in turbidity, resulting from the removal of sediment of the river bed in order to open the ditch. This impact was shown to be well tolerated by the body water, after crossing back to normal conditions. Regarding the Monitoring of Water Quality, which usually increases the cost of the venture, this was not an effective instrument for the control of impacts due to the time needed to obtain the results of samples taken compared to the time of execution of the crossing. (author)

Control of a nursing bed based on a hybrid brain-computer interface.

Science.gov (United States)

Nengneng Peng; Rui Zhang; Haihua Zeng; Fei Wang; Kai Li; Yuanqing Li; Xiaobin Zhuang

2016-08-01

In this paper, we propose an intelligent nursing bed system which is controlled by a hybrid brain-computer interface (BCI) involving steady-state visual evoked potential (SSVEP) and P300. Specifically, the hybrid BCI includes an asynchronous brain switch based on SSVEP and P300, and a P300-based BCI. The brain switch is used to turn on/off the control system of the electric nursing bed through idle/control state detection, whereas the P300-based BCI is for operating the nursing bed. At the beginning, the user may focus on one group of flashing buttons in the graphic user interface (GUI) of the brain switch, which can simultaneously evoke SSVEP and P300, to switch on the control system. Here, the combination of SSVEP and P300 is used for improving the performance of the brain switch. Next, the user can control the nursing bed using the P300-based BCI. The GUI of the P300-based BCI includes 10 flashing buttons, which correspond to 10 functional operations, namely, left-side up, left-side down, back up, back down, bedpan open, bedpan close, legs up, legs down, right-side up, and right-side down. For instance, he/she can focus on the flashing button "back up" in the GUI of the P300-based BCI to activate the corresponding control such that the nursing bed is adjusted up. Eight healthy subjects participated in our experiment, and obtained an average accuracy of 93.75% and an average false positive rate (FPR) of 0.15 event/min. The effectiveness of our system was thus demonstrated.

Homeopathy for mental fatigue: lessons from a randomized, triple blind, placebo-controlled cross-over clinical trial

Directory of Open Access Journals (Sweden)

Dean Michael

2012-10-01

Full Text Available Abstract Background Difficulty in controlling attention can lead to mental fatigue in the healthy population. We identified one trial reporting a benefit in patients’ attention using a homeopathic formula preparation. One component of the preparation was potassium phosphate, widely available off the shelf as Kali phos 6x for cognitive problems. The aim of this exploratory trial was to assess the effectiveness of Kali phos 6x for attention problems associated with mental fatigue. Methods We recruited student and staff volunteers (University of York with self-reported mental fatigue, excluding any using homeopathy or prescribed stimulants, or with a diagnosis of chronic fatigue syndrome. In a triple blind, cross-over, placebo-controlled clinical trial, 86 volunteers were randomized to receive Kali phos 6x or identical placebo 10 minutes before taking a psychological test of attention (Stroop Colour-Word Test. One week later they were crossed over and took the other preparation before repeating the test. Results We found no evidence of a treatment effect in a comparison of Kali phos 6x with placebo (Kali phos minus placebo = −1.1 (95% CI −3.0 to 0.9, P = 0.3 Stroop score units, Cohen effect size = −0.17 even when allowing for a weak period effect with accuracy scores in the second period being higher than those in the first (P = 0.05. We observed a ceiling effect in the Stroop test which undermined our ability to interpret this result. Conclusions Kali phos 6x was not found to be effective in reducing mental fatigue. A ceiling effect in our primary outcome measure meant that we could not rule out a type II error. Thorough piloting of an adequate outcome measure could have led to an unequivocal result. Current Controlled Trials ISRCTN16521161

BED estimates of HIV incidence: resolving the differences, making things simpler.

Directory of Open Access Journals (Sweden)

John Hargrove

Full Text Available Develop a simple method for optimal estimation of HIV incidence using the BED capture enzyme immunoassay.Use existing BED data to estimate mean recency duration, false recency rates and HIV incidence with reference to a fixed time period, T.Compare BED and cohort estimates of incidence referring to identical time frames. Generalize this approach to suggest a method for estimating HIV incidence from any cross-sectional survey.Follow-up and BED analyses of the same, initially HIV negative, cases followed over the same set time period T, produce estimates of the same HIV incidence, permitting the estimation of the BED mean recency period for cases who have been HIV positive for less than T. Follow-up of HIV positive cases over T, similarly, provides estimates of the false-recent rate appropriate for T. Knowledge of these two parameters for a given population allows the estimation of HIV incidence during T by applying the BED method to samples from cross-sectional surveys. An algorithm is derived for providing these estimates, adjusted for the false-recent rate. The resulting estimator is identical to one derived independently using a more formal mathematical analysis. Adjustments improve the accuracy of HIV incidence estimates. Negative incidence estimates result from the use of inappropriate estimates of the false-recent rate and/or from sampling error, not from any error in the adjustment procedure.Referring all estimates of mean recency periods, false-recent rates and incidence estimates to a fixed period T simplifies estimation procedures and allows the development of a consistent method for producing adjusted estimates of HIV incidence of improved accuracy. Unadjusted BED estimates of incidence, based on life-time recency periods, would be both extremely difficult to produce and of doubtful value.

Bed Bugs

Science.gov (United States)

Prevent, identify, and treat bed bug infestations using EPA’s step-by-step guides, based on IPM principles. Find pesticides approved for bed bug control, check out the information clearinghouse, and dispel bed bug myths.

Realization of a gamma emission tomography by a servo-controlled camera and bed

International Nuclear Information System (INIS)

Parmentier, M.; Gunzman, D.; Bidet, R.

1979-01-01

A gamma-camera and a whole-body bed were connected to a minicomputer which controlled automatically their movements. By combining horizontal displacement of the bed with vertical displacement and rotation of the camera we were able to obtain the equivalent of camera rotation around the bed. This method provides an inexpensive way of realizing gamma emission tomography [fr

Catalytic wet oxidation of phenol in a trickle bed reactor over a Pt/TiO2 catalyst.

Science.gov (United States)

Maugans, Clayton B; Akgerman, Aydin

2003-01-01

Catalytic wet oxidation of phenol was studied in a batch and a trickle bed reactor using 4.45% Pt/TiO2 catalyst in the temperature range 150-205 degrees C. Kinetic data were obtained from batch reactor studies and used to model the reaction kinetics for phenol disappearance and for total organic carbon disappearance. Trickle bed experiments were then performed to generate data from a heterogeneous flow reactor. Catalyst deactivation was observed in the trickle bed reactor, although the exact cause was not determined. Deactivation was observed to linearly increase with the cumulative amount of phenol that had passed over the catalyst bed. Trickle bed reactor modeling was performed using a three-phase heterogeneous model. Model parameters were determined from literature correlations, batch derived kinetic data, and trickle bed derived catalyst deactivation data. The model equations were solved using orthogonal collocations on finite elements. Trickle bed performance was successfully predicted using the batch derived kinetic model and the three-phase reactor model. Thus, using the kinetics determined from limited data in the batch mode, it is possible to predict continuous flow multiphase reactor performance.

The bedding environment, sleep position, and frequent wheeze in childhood.

Science.gov (United States)

Ponsonby, Anne-Louise; Dwyer, Terence; Trevillian, Leigh; Kemp, Andrew; Cochrane, Jennifer; Couper, David; Carmichael, Allan

2004-05-01

Synthetic quilt use has been associated with increased childhood wheeze in previous studies. Our aim was to examine whether the adverse effect of synthetic quilt use on frequent wheeze differed by usual sleep position. A population-based cross-sectional study of 6378 (92% of those eligible) 7-year-olds in Tasmania, Australia, was conducted in 1995. Exercise-challenge lung function was obtained on a subset of 414 children from randomly selected schools. Child bedding including pillow and overbedding composition and usual sleep position by parental questionnaire. Frequent wheeze (>12 wheeze episodes over the past year), using the International Study of Asthma and Allergies in Childhood parental questionnaire, and baseline and postexercise forced expiratory volume in 1 second lung-function measures. Frequent wheeze (n = 117) was positively associated with synthetic quilts, synthetic pillows, electric blankets, and sleeping in a bottom bunk bed but did not vary by sleep position. In a nested case-control analysis, the association between synthetic quilt use and frequent wheeze differed by sleep position. Among children who slept supine, synthetic (versus feather) quilt use was associated with frequent wheeze (adjusted odds ratio: 2.37 [1.08, 5.23]). However, among nonsupine sleepers, overlying synthetic quilt use was not associated with frequent wheeze (adjusted odds ratio: 1.06 [0.60, 1.88]). This difference in quilt effect by sleep position was highly significant. Similarly, synthetic quilt use was associated with lower postexercise forced expiratory volume in 1 second measures among supine but not nonsupine sleeping children. An increasing focus on the bedding environment immediately adjacent to the nose and mouth is required for respiratory disorders provoked by bedding, such as child asthma characterized by frequent wheeze.

Effect of bedding control on amount of house dust mite allergens, asthma symptoms, and peak expiratory flow rate.

Science.gov (United States)

Lee, Inn-Sook

2003-04-30

This quasi-experimental study was designed to investigate the effect of bedding control on the amount of house dust mite (HDM) allergens, asthma symptoms, and peak expiratory flow rate (PEFR) in asthmatics sensitive to HDMs. The subjects in the study were drawn from patients receiving treatment at the allergy clinics of three university-affiliated hospitals in Seoul. Forty-two patients without prior practice of the bedding control used in this study were selected. They commonly showed bronchial asthma caused by HDMs, and exhibited strong positive points (more than 3 points) in skin prick test (D. farinae, D. pteronyssinus), and positive response in both fluoro-allergosorbent test (FAST), and PC20 methacholine test. Of the subjects, alternatively, 22 were assigned to the experimental group and 20 to control group. Bedding control consisted of the use of outer cotton covers, boiling them for 10 minutes fortnightly, and disinfecting bedding by sunlight fortnightly. The experimental group was under bedding control for 4 weeks. The data were collected from October 2000 to January 2001. The results were as follows: 1. After bedding control, the total amount of HDM allergens decreased significantly in the experimental group. However there was no significant difference in the decrease of the amount of HDM allergens between the two groups. 2. Of the asthma symptoms, there was significant difference only in the decrease of the frequency of dyspnea, and in the increase of sleeping disturbance between the two groups after bedding control. 3. After bedding control, PEFR increased in the experimental group whereas it decreased in the control group. However, neither change was significant. The above findings indicate that bedding control improved several asthma symptoms in asthmatics sensitive to HDMs. Accordingly, we suggest that bedding control is adopted as a useful nursing intervention in the field.

A scaled experimental study of control blade insertion dynamics in Pebble-Bed Fluoride-Salt-Cooled High-Temperature Reactors

Energy Technology Data Exchange (ETDEWEB)

Buster, Grant C., E-mail: grant.buster@gmail.com; Laufer, Michael R.; Peterson, Per F.

2016-07-15

Highlights: • A granular dynamics scaling methodology is discussed. • Control blade insertion in a representative pebble-bed core is experimentally studied. • Control blade insertion forces and pebble displacements are experimentally measured. • X-ray tomography techniques are used to observe pebble displacement distributions. - Abstract: Direct control element insertion into a pebble-bed reactor core is proposed as a viable control system in molten-salt-cooled pebble-bed reactors. Unlike helium-cooled pebble-bed reactors, this reactor type uses spherical fuel elements with near-neutral buoyancy in the molten-salt coolant, thus reducing contact forces on the fuel elements. This study uses the X-ray Pebble Bed Recirculation Experiment facility to measure the force required to insert a control element directly into a scaled pebble-bed. The required control element insertion force, and therefore the contact force on fuel elements, is measured to be well below recommended limits. Additionally, X-ray tomography is used to observe how the direct insertion of a control element physically displaces spherical fuel elements. The tomography results further support the viability of direct control element insertion into molten-salt-cooled pebble-bed reactor cores.

Control, data acquisition and analysis for the JET neutral injection test bed

International Nuclear Information System (INIS)

Jones, T.T.C.; Brenan, P.R.; Rodgers, M.E.; Stork, D.; Young, I.D.

1984-01-01

The Neutral Injection Test-Bed (NITB) is a major experimental assembly in support of the Neutral Beam Heating Programme for JET. In addition to its prime function of testing the Neutral Injection hardware, the Test Bed serves as the prototype to test the computer control and data acquisition system, which is described. (author)

Efficacy of an Essential Oil-Based Pesticide for Controlling Bed Bug (Cimex lectularius Infestations in Apartment Buildings

Directory of Open Access Journals (Sweden)

Changlu Wang

2014-11-01

Full Text Available Bed bugs (Cimex lectularius L. and Cimex hemipterus F. are among the most difficult urban pests to manage. Many essential oil-based bed bug control products that are considered reduced risk to mammals compared to synthetic insect neurotoxins have become commercially available, but their effectiveness as a stand-alone control method is unknown. This study assessed the field efficacy of an essential oil-based bed bug control product (EcoRaider; a.i. 1% geraniol + 1% cedar oil + 2% sodium lauryl sulfate compared to a pyrethroid and neonicotinoid mixture spray (0.075% Temprid SC; a.i. beta-cyfluthrin + imidacloprid. After 12 weeks, the three treatments—EcoRaider, Temprid SC, and EcoRaider + Temprid SC caused 92.5 ± 2.7, 92.9 ± 3.0, and 91.7% ± 2.7% bed bug count reduction, respectively. No significant differences existed in the bed bug reduction among the treatments. Bed bugs were eliminated from only 22% of the treated apartments. Among those still with bed bugs, 76% of the residents did not know bed bugs were present. We documented the residents’ self-control practices and discussed the potential of using essential oil-based insecticides in bed bug management programs to minimize the health risks to building occupants and pets and to slow down the development of insecticide resistance.

Genetical control of mitotic crossing over in yeast

International Nuclear Information System (INIS)

Fedorova, I.V.; Marfin, A.B.

1982-01-01

Lethal effect of 8 methoxypsoralen (8-MOP) and long-wave ultraviolet radiation (LUR) on diploid and haploid radiosensitive strains of yeast LSaccharomyces cerevisiae has been studied. It is shown that wild type diploids and homozygous with respect to locus rad 2 is considerably more stable than corresponding haploids, while diploid homozygous with respect to rad 54 locus is more sensitive than haploid. Use of the method of repeated irradiation permitted to study capability of radiosensitive diploids to remove 8 MOP-induced DNA photodamages-monoadducts. This process proceeds effectively in the wild type strain and rad 54 rad 54 diploid and was absent in rad 2 rad 2 diploid. Very strong recombinogenous effect of 8-MOP and LUR was discovered when studying mitotic segregation and crossing-over. It is also shown that rad 2 mutation increases slightly and rad 54 mutation decreases sharply frequency of recombination events in yeast cells. It is established by means of the repeated irradiation method that the main contribution to the 8 MOP and LUR recombinogenous effect is made with DNA sutures induced with these agents. Possible participation of different repair systems in the recombination processes induced with 8 MOP and LUR in yeast cells is discussed

Mass transfer controlled reactions in packed beds at low Reynolds numbers

Energy Technology Data Exchange (ETDEWEB)

Fedkiw, P.S.

1978-12-01

The a priori prediction and correlation of mass-transfer rates in transport limited, packed-bed reactors at low Reynolds numbers is examined. The solutions to the governing equations for a flow-through porous electrode reactor indicate that these devices must operate at a low space velocity to suppress a large ohmic potential drop. Packed-bed data for the mass-transfer rate at such low Reynolds numbers were examined and found to be sparse, especially in liquid systems. Prior models to simulate the solid-void structure in a bed are reviewed. Here the bed was envisioned as an array of sinusoidal periodically constricted tubes (PCT). Use of this model has not appeared in the literature. The velocity field in such a tube should be a good approximation to the converging-diverging character of the velocity field in an actual bed. The creeping flow velocity profiles were calculated. These results were used in the convective-diffusion equation to find mass transfer rates at high Peclet number for both deep and shallow beds, for low Peclet numbers in a deep bed. All calculations assumed that the reactant concentration at the tube surface is zero. Mass-transfer data were experimentally taken in a transport controlled, flow-through porous electrode to test the theoretical calculations and to provide data resently unavailable for deeper beds. It was found that the sinusoidal PCT model could not fit the data of this work or that available in the literature. However, all data could be adequately described by a model which incorporates a channelingeffect. The bed was successfully modeled as an array of dual sized straight tubes.

Test bed control center design concept for Tank Waste Retrieval Manipulator Systems

International Nuclear Information System (INIS)

Sundstrom, E.; Draper, J.V.; Fausz, A.

1995-01-01

This paper describes the design concept for the control center for the Single Shell Tank Waste Retrieval Manipulator System test bed and the design process behind the concept. The design concept supports all phases of the test bed mission, including technology demonstration, comprehensive system testing, and comparative evaluation for further development and refinement of the TWRMS for field operations

A Non-Equilibrium Sediment Transport Model for Dam Break Flow over Moveable Bed Based on Non-Uniform Rectangular Mesh

Directory of Open Access Journals (Sweden)

Gangfeng Wu

2018-05-01

Full Text Available The use of multiple-level non-uniform rectangular mesh in coupled flow and sediment transport modeling is preferred to achieve high accuracy in important region without increasing computational cost greatly. Here, a robust coupled hydrodynamic and non-equilibrium sediment transport model is developed on non-uniform rectangular mesh to simulate dam break flow over movable beds. The enhanced shallow water and sediment transport equations are adopted to consider the mass and momentum exchange between the flow phase and sediment phase. The flux at the interface is calculated by the positivity preserving central upwind scheme, which belongs to Godunov-type Riemann-problem-solver-free central schemes and is less expensive than other popular Riemann solvers while still capable of tracking wet/dry fronts accurately. The nonnegative water depth reconstruction method is used to achieve second-order accuracy in space. The model was first verified against two laboratory experiments of dam break flow over irregular fixed bed. Then the quantitative performance of the model was further investigated by comparing the computational results with measurement data of dam break flow over movable bed. The good agreements between the measurements and the numerical simulations are found for the flow depth, velocity and bed changes.

Trickle bed reactor for the oxidation of phenol over active carbon catalyst

OpenAIRE

Gabbiye, Nigus; Font Capafons, Josep; Fortuny Sanromá, Agustín; Bengoa, Christophe José; Fabregat Llangotera, Azael; Stüber, Frank Erich

2009-01-01

The catalytic wet air oxidation of phenol using activated carbon has been performed in a laboratory trickle bed reactor over a wide range of operating variables (PO2, T, FL and Cph,o) and hydrodynamic conditions. The influence of different start-up procedures (saturation of activated carbon) has also been tested. Further improvement of activity and stability has been checked for by using dynamic TBR operation concept or impregnated Fe/carbon catalyst. The results obtained confi...

Dialysis-associated hypertension treated with Telmisartan--DiaTel: a pilot, placebo-controlled, cross-over, randomized trial.

Directory of Open Access Journals (Sweden)

Matthias Huber

Full Text Available Treatment of hypertension in hemodialysis (HD patients is characterised by lack of evidence for both the blood pressure (BP target goal and the recommended drug class to use. Telmisartan, an Angiotensin receptor blocker (ARB that is metabolised in the liver and not excreted via HD extracorporeal circuit might be particularly suitable for HD patients. We designed and conducted a randomised, placebo-controlled, double-blind and cross-over trial for treatment of dialysis-associated hypertension with telmisartan 80 mg once daily or placebo on top of standard antihypertensive treatment excluding other Renin-Angiotensin-System (RAS blockers. In 29 patients after randomization we analysed BP after a treatment period of 8 weeks, while 13 started with telmisartan and 16 with placebo; after 8 weeks 11 continued with telmisartan and 12 with placebo after cross-over, respectively. Patients exhibited a significant reduction of systolic pre-HD BP from 141.9±21.8 before to 131.3±17.3 mmHg after the first treatment period with telmisartan or placebo. However, no average significant influence of telmisartan was observed compared to placebo. The latter may be due to a large inter-individual variability of BP responses reaching from a 40 mmHg decrease under placebo to 40 mmHg increase under telmisartan. Antihypertensive co-medication was changed for clinical reasons in 7 out of 21 patients with no significant difference between telmisartan and placebo groups. Our starting hypothesis, that telmisartan on top of standard therapy lowers systolic office BP in HD patients could not be confirmed. In conclusion, this small trial indicates that testing antihypertensive drug efficacy in HD patients is challenging due to complicated standardization of concomitant medication and other confounding factors, e.g. volume status, salt load and neurohormonal activation, that influence BP control in HD patients.Clinicaltrialsregister.eu 2005-005021-60.

Dissolved oxygen control in a coupled fluidized bed system

International Nuclear Information System (INIS)

Jones, R.M.; Melcer, H.

1988-01-01

The biological fluidized bed process is a modification of more conventional fixed film processes, such as the trickling filter, in which wastewater is passed upward through a bed of granular support medium, typically sand, at a sufficient velocity to expand or fluidize the medium. The granular medium provides a large surface area for the establishment of a biological film. The fluidized bed process was selected to investigate the treatment of coking plant wastewaters in view of the significant advantages offered in terms of reduced reactor volumes that result from the high biomass concentration maintained on the support medium. The technical feasibility of treating coal distillation condensates was evaluated during a 3-year study at Environment Canada's Wastewater Technology Centre (WTC). The feed to the pilot scale test system consisted of effluent from fixed and free leg ammonia stills at the by-product coke plant of Dofasco Inc. in Hamilton, Ontario. The pilot plant consisted of two fluidized bed reactors in series, coupled to provide carbon oxidation, nitrification and denitrification in the predenitrification operating mode. The anoxic denitrification reactor was 115 mm in diameter and the oxygenic nitrification reactor, 290 mm in diameter. The bed heights and reactor volumes were adjustable by relocation of the position of the sand/biomass wasting valve. The experimental objective of this research was to determine those operating conditions required to maintain stable nitrification and complete denitrification under both steady state and dynamic operating conditions. Details regarding operating, sampling and analytic procedures have been presented elsewhere. A specific operating problem existed relating to the control of the dissolved oxygen concentration in the oxygenic fluidized bed reactor, the solution of which forms the basis of the paper

Nonlinear dynamics and control of a recycle fixed bed reactor

DEFF Research Database (Denmark)

Recke, Bodil; Jørgensen, Sten Bay

1997-01-01

The purpose of this paper is twofold. Primarily to describe the dynamic behaviour that can be observed in a fixed bed reactor with recycle of unconverted reactant. Secondly to describe the possibilities of model reduction in order to facilitate control design. Reactant recycle has been shown...... to introduce periodic solution to the fixed bed reactor, a phenomenon which is not seen for the system without the recycle, at least not within the Peclet number range investigated in the present work. The possibility of model reduction by the methods of modal decomposition, and by characteristics...

Using multiple bed load measurements: Toward the identification of bed dilation and contraction in gravel-bed rivers

Science.gov (United States)

Marquis, G. A.; Roy, A. G.

2012-02-01

This study examines bed load transport processes in a small gravel-bed river (Béard Creek, Québec) using three complementary methods: bed elevation changes between successive floods, bed activity surveys using tags inserted into the bed, and bed load transport rates from bed load traps. The analysis of 20 flood events capable of mobilizing bed material led to the identification of divergent results among the methods. In particular, bed elevation changes were not consistent with the bed activity surveys. In many cases, bed elevation changes were significant (1 to 2 times the D50) even if the bed surface had not been activated during the flood, leading to the identification of processes of bed dilation and contraction that occurred over 10% to 40% of the bed surface. These dynamics of the river bed prevent accurate derivation of bed load transport rates from topographic changes, especially for low magnitude floods. This paper discusses the mechanisms that could explain the dilation and contraction of particles within the bed and their implications in fluvial dynamics. Bed contraction seems to be the result of the winnowing of the fine sediments under very low gravel transport. Bed dilation seems to occur on patches of the bed at the threshold of motion where various processes such as fine sediment infiltration lead to the maintenance of a larger sediment framework volume. Both processes are also influenced by flood history and the initial local bed state and in turn may have a significant impact on sediment transport and morphological changes in gravel-bed rivers.

Tanning beds: A call to action for further educational and legislative efforts.

Science.gov (United States)

Farley, Clara; Alimi, Yewande; Espinosa, Lauren R; Perez, Sebastian; Knechtle, William; Hestley, Andrea; Carlson, Grant W; Russell, Maria C; Delman, Keith A; Rizzo, Monica

2015-08-01

Melanoma is steadily increasing over the past decade. Recent studies confirmed a link between tanning bed use and melanoma. We sought to determine the prevalence and frequency of tanning bed among young patients with melanoma. We retrospectively analyzed tanning bed use among young melanoma patients compared to controls selected from the hospital medical records. A telephone survey investigated family history of melanoma or skin cancer, hair color, eye color, skin type, tanning bed use, and patient awareness of dangers of tanning bed use. A total of 601 melanoma cases were identified; 265 (44%) completed the telephone survey as did 195 (31%) controls. Of these 460 subjects, 260 were female. Females were 3.0 times more likely to have used a tanning bed. Melanoma patients had natural light color hair, blue-green eyes, and 2.0 times more likely to use a tanning bed than controls. Among the tanning bed users, 90% were aware of danger of tanning bed. Our study found that tanning beds were more likely to be used by young women, the majority of whom are aware of the associated risks. Eliminating the use of tanning beds should be considered to decrease the incidence of melanoma. © 2015 Wiley Periodicals, Inc.

Adaptive control of paste drying in spouted bed using the GPC algorithm

Directory of Open Access Journals (Sweden)

Corrêa N.A.

2000-01-01

Full Text Available Spouted bed is an equipment reasonable investigated for drying of many and different materials ranging from granules to pastes and suspensions. This work presents an implementation and tests of an advanced control strategy (GPC on a spouted bed dryer. Water was used as the ideal paste for tests. A microcomputer PC-486 type was used to maintain humidity and temperature set points of air in the dryer by manipulating electric power of heat exchanger and paste feed flow rate. An instrumentation was set-up with different sensors, interface and final control elements for the process. The tests were carried out with pure water as ideal paste. Stability and performance analysis of the control strategy were accomplished. A stable controller was obtained which encouraged us to investigate this control strategy in the drying of other pastes too.

Impact of palm date consumption on microbiota growth and large intestinal health: a randomised, controlled, cross-over, human intervention study.

Science.gov (United States)

Eid, Noura; Osmanova, Hristina; Natchez, Cecile; Walton, Gemma; Costabile, Adele; Gibson, Glenn; Rowland, Ian; Spencer, Jeremy P E

2015-10-28

The reported inverse association between the intake of plant-based foods and a reduction in the prevalence of colorectal cancer may be partly mediated by interactions between insoluble fibre and (poly)phenols and the intestinal microbiota. In the present study, we assessed the impact of palm date consumption, rich in both polyphenols and fibre, on the growth of colonic microbiota and markers of colon cancer risk in a randomised, controlled, cross-over human intervention study. A total of twenty-two healthy human volunteers were randomly assigned to either a control group (maltodextrin-dextrose, 37·1 g) or an intervention group (seven dates, approximately 50 g). Each arm was of 21 d duration and was separated by a 14-d washout period in a cross-over manner. Changes in the growth of microbiota were assessed by fluorescence in situ hybridisation analysis, whereas SCFA levels were assessed using HPLC. Further, ammonia concentrations, faecal water genotoxicity and anti-proliferation ability were also assessed using different assays, which included cell work and the Comet assay. Accordingly, dietary intakes, anthropometric measurements and bowel movement assessment were also carried out. Although the consumption of dates did not induce significant changes in the growth of select bacterial groups or SCFA, there were significant increases in bowel movements and stool frequency (Pfruit intake significantly reduced genotoxicity in human faecal water relative to control (Pfruit may reduce colon cancer risk without inducing changes in the microbiota.

Evaluation of a clay-based acidic bedding conditioner for dairy cattle bedding.

Science.gov (United States)

Proietto, R L; Hinckley, L S; Fox, L K; Andrew, S M

2013-02-01

This study investigated the effects of a clay-based acidic bedding conditioner on sawdust bedding pH, dry matter (DM), environmental pathogen counts, and environmental bacterial counts on teat ends of lactating dairy cows. Sixteen lactating Holstein cows were paired based on parity, days in milk, milk yield, and milk somatic cell count, and were negative for the presence of an intramammary pathogen. Within each pair, cows were randomly assigned to 1 of 2 treatments with 3-wk periods in a crossover design. Treatment groups consisted of 9 freestalls per group bedded with either untreated sawdust or sawdust with a clay-based acidic bedding conditioner, added at 3- to 4-d intervals over each 21-d period. Bedding and teat ends were aseptically sampled on d 0, 1, 2, 7, 14, and 21 for determination of environmental bacterial counts. At the same time points, bedding was sampled for DM and pH determination. The bacteria identified in the bedding material were total gram-negative bacteria, Streptococcus spp., and coliform bacteria. The bacteria identified on the teat ends were Streptococcus spp., coliform bacteria, and Klebsiella spp. Teat end score, milk somatic cell count, and intramammary pathogen presence were measured weekly. Bedding and teat cleanliness, environmental high and low temperatures, and dew point data were collected daily. The bedding conditioner reduced the pH, but not the DM, of the sawdust bedding compared with untreated sawdust. Overall environmental bacterial counts in bedding were lower for treated sawdust. Total bacterial counts in bedding and on teat ends increased with time over both periods. Compared with untreated sawdust, the treated bedding had lower counts of total gram-negative bacteria and streptococci, but not coliform counts. Teat end bacterial counts were lower for cows bedded on treated sawdust for streptococci, coliforms, and Klebsiella spp. compared with cows bedded on untreated sawdust. The clay-based acidic bedding conditioner

Bed-material entrainment and associated transportation infrastructure problems in streams of the Edwards Plateau, central Texas

Science.gov (United States)

Heitmuller, Franklin T.; Asquith, William H.

2008-01-01

The Texas Department of Transportation commonly builds and maintains low-water crossings (LWCs) over streams in the Edwards Plateau in Central Texas. LWCs are low-height structures, typically constructed of concrete and asphalt, that provide acceptable passage over seasonal rivers or streams with relatively low normal-depth flow. They are designed to accommodate flow by roadway overtopping during high-flow events. The streams of the Edwards Plateau are characterized by cobble- and gravel-sized bed material and highly variable flow regimes. Low base flows that occur most of the time occasionally are interrupted by severe floods. The floods entrain and transport substantial loads of bed material in the stream channels. As a result, LWCs over streams in the Edwards Plateau are bombarded and abraded by bed material during floods and periodically must be maintained or even replaced.

DMFC performance and methanol cross-over: Experimental analysis and model validation

Energy Technology Data Exchange (ETDEWEB)

Casalegno, A.; Marchesi, R. [Dipartimento di Energia, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milano (Italy)

2008-10-15

A combined experimental and modelling approach is proposed to analyze methanol cross-over and its effect on DMFC performance. The experimental analysis is performed in order to allow an accurate investigation of methanol cross-over influence on DMFC performance, hence measurements were characterized in terms of uncertainty and reproducibility. The findings suggest that methanol cross-over is mainly determined by diffusion transport and affects cell performance partly via methanol electro-oxidation at the cathode. The modelling analysis is carried out to further investigate methanol cross-over phenomenon. A simple model evaluates the effectiveness of two proposed interpretations regarding methanol cross-over and its effects. The model is validated using the experimental data gathered. Both the experimental analysis and the proposed and validated model allow a substantial step forward in the understanding of the main phenomena associated with methanol cross-over. The findings confirm the possibility to reduce methanol cross-over by optimizing anode feeding. (author)

Predicting Bed Mobility in a Simple River Channel

Science.gov (United States)

Wydzga, M. A.; Legleiter, C.; Dunne, T.

2007-12-01

Prediction of the frequency and spatial pattern of bed mobility in gravel bed rivers is central to a wide range of theoretical and applied interests ranging from sediment transport to the impacts of natural or managed floods on aquatic organisms. Although bed mobility has been investigated in numerous flume and field studies, accurate predictions of grain entrainment and transport in gravel bed rivers remain elusive. Alluvial rivers typically encompass a much wider range of hydraulic and sedimentological conditions than those that have been recreated in laboratory flume studies upon which many grain entrainment and transport models are based. These flume studies are limited to the examination of processes occurring over the short term, commonly with the absence of slower processes such as fine-grain infilling. On the other hand, in field studies key variables can not be controlled and the spatial complexity of processes and conditions complicate data collection and analysis. A unique opportunity currently exists to help bridge this gap between laboratory and field studies: a 3.2 km long, recently constructed, single thread, alternate bar, gravel bed river channel of the Merced River. This channel, constructed for ecosystem restoration purposes, is slowly developing greater complexity, but is still currently defined by a simple plan form and cross-sectional channel geometry compared to most natural gravel bed river channels. This channel can thus be considered a full-scale flume. In the six years since the channel was constructed, a wider range of sedimentological bed conditions have evolved than have been created in a laboratory flume. We are characterizing the bed grain sizes, flow field, grain entrainment, and the sedimentological or bed state conditions in this simple channel. The flow field is modeled using a calibrated, 2D hydrodynamic flow model, MD_SWMS. Grain entrainment is measured with both metal tags inserted into the bed, and painted rock tracers

Large Eddy Simulations of Compositional Density Currents Flowing Over a Mobile Bed

Science.gov (United States)

Kyrousi, Foteini; Zordan, Jessica; Leonardi, Alessandro; Juez, Carmelo; Zanello, Francesca; Armenio, Vincenzo; Franca, Mário J.

2017-04-01

Density currents are a ubiquitous phenomenon caused by natural events or anthropogenic activities, and play an important role in the global sediment cycle; they are agents of long distance sediment transport in lakes, seas and oceans. Density gradients induced by salinity, temperature differences, or by the presence of suspended material are all possible triggers of a current. Such flows can travel long distances while eroding or depositing bed materials. This can provoke rapid topological changes, which makes the estimation of their transport capacity of prime interest for environmental engineering. Despite their relevance, field data regarding their dynamics is limited due to density currents scattered and unpredictable occurrence in nature. For this reason, laboratory experiments and numerical simulations have been a preferred way to investigate sediment transport processes associated to density currents. The study of entrainment and deposition processes requires detailed data of velocities spatial and temporal distributions in the boundary layer and bed shear stress, which are troublesome to obtain in laboratory. Motivated by this, we present 3D wall-resolved Large Eddy Simulations (LES) of density currents generated by lock-exchange. The currents travel over a smooth flat bed, which includes a section composed by erodible fine sediment susceptible of eroding. Several sediment sizes and initial density gradients are considered. The grid is set to resolve the velocity field within the boundary layer of the current (a tiny fraction of the total height), which in turn allows to obtain predictions of the bed shear stress. The numerical outcomes are compared with experimental data obtained with an analogous laboratory setting. In laboratory experiments salinity was chosen for generating the initial density gradient in order to facilitate the identification of entrained particles, since salt does not hinder the possibility to track suspended particles. Under these

Dicyclopentadiene Hydrogenation in Trickle Bed Reactor under Forced Periodic Control

Czech Academy of Sciences Publication Activity Database

Skála, D.; Hanika, Jiří

2008-01-01

Roč. 62, č. 2 (2008), s. 215-218 ISSN 1336-7242 R&D Projects: GA MPO(CZ) FT-TA/039 Institutional research plan: CEZ:AV0Z40720504 Keywords : periodic control * trickle -bed reactor * dicyclopentadiene Subject RIV: CI - Industrial Chemistry, Chemical Engineering

Cross-Layer Design of Source Rate Control and Congestion Control for Wireless Video Streaming

Directory of Open Access Journals (Sweden)

Peng Zhu

2007-01-01

Full Text Available Cross-layer design has been used in streaming video over the wireless channels to optimize the overall system performance. In this paper, we extend our previous work on joint design of source rate control and congestion control for video streaming over the wired channel, and propose a cross-layer design approach for wireless video streaming. First, we extend the QoS-aware congestion control mechanism (TFRCC proposed in our previous work to the wireless scenario, and provide a detailed discussion about how to enhance the overall performance in terms of rate smoothness and responsiveness of the transport protocol. Then, we extend our previous joint design work to the wireless scenario, and a thorough performance evaluation is conducted to investigate its performance. Simulation results show that by cross-layer design of source rate control at application layer and congestion control at transport layer, and by taking advantage of the MAC layer information, our approach can avoid the throughput degradation caused by wireless link error, and better support the QoS requirements of the application. Thus, the playback quality is significantly improved, while good performance of the transport protocol is still preserved.

Fluidized bed reactor for working up carbon coated particles

International Nuclear Information System (INIS)

Marschollek, M.; Simon, W.; Walter, C.

1981-01-01

A fluidized bed reactor is described for working up carbon coated particles, particularly nuclear fuel particles or fertile material particles consisting essentially of a cylindrical portion connected to a conical portion. Gas supply pipes, gas distribution space and gas distribution heads are provided within the conical reactor lower portion, the gas distribution members being arranged in at least two superimposed planes and distributed symmetrically over the cross-section of the reactor

Cross-Layer Adaptive Feedback Scheduling of Wireless Control Systems

Science.gov (United States)

Xia, Feng; Ma, Longhua; Peng, Chen; Sun, Youxian; Dong, Jinxiang

2008-01-01

There is a trend towards using wireless technologies in networked control systems. However, the adverse properties of the radio channels make it difficult to design and implement control systems in wireless environments. To attack the uncertainty in available communication resources in wireless control systems closed over WLAN, a cross-layer adaptive feedback scheduling (CLAFS) scheme is developed, which takes advantage of the co-design of control and wireless communications. By exploiting cross-layer design, CLAFS adjusts the sampling periods of control systems at the application layer based on information about deadline miss ratio and transmission rate from the physical layer. Within the framework of feedback scheduling, the control performance is maximized through controlling the deadline miss ratio. Key design parameters of the feedback scheduler are adapted to dynamic changes in the channel condition. An event-driven invocation mechanism for the feedback scheduler is also developed. Simulation results show that the proposed approach is efficient in dealing with channel capacity variations and noise interference, thus providing an enabling technology for control over WLAN. PMID:27879934

The Effects of Dinner-to-Bed Time and Post-Dinner Walk on Gastric Cancer Across Different Age Groups: A Multicenter Case-Control Study in Southeast China.

Science.gov (United States)

Xu, Le; Zhang, Xi; Lu, Jun; Dai, Jia-Xi; Lin, Ren-Qin; Tian, Fang-Xi; Liang, Bing; Guo, Yi-Nan; Luo, Hui-Yu; Li, Ni; Fang, Dong-Ping; Zhao, Ruo-Hua; Huang, Chang-Ming

2016-04-01

Gastric cancer (GC) remains a major killer throughout the world. Despite the dramatic decrease in GC over the last century, its etiology has not yet been well characterized. This study investigated the possible independent and combined effects of the dinner-to-bed time and post-dinner walk on the risk for GC across different age groups. A population-based, case-control study was conducted in southeast China, including 452 patients with GC and 465 age-, race-, and gender-matched controls. A self-designed questionnaire was used to collect information on demographic characteristics, dinner-to-bed time, post-dinner walk, and other behavioral factors. Conditional logistic regression models were used to estimate the effects of the dinner-to-bed time and post-dinner walk as well as their joint effect on the risk for GC across different age groups. Individuals with dinner-to-bed time 55 years old.

The CRO-1 gene of Saccharomyces cerevisiae controls mitotic crossing over, chromosomal stability and sporulation

International Nuclear Information System (INIS)

Esposito, M.S.; Maleas, D.T.; Bjornstad, K.A.; Holbrook, L.L.

1987-01-01

The properties of a novel temperature-sensitive recombination-defective mutant of Saccharomyces cerevisiae, cro1-1 is described. The cro1-1 mutant is the first instance of a rec mutation that reduces drastically the rates of spontaneous mitotic crossing-over events but not those of gene conversional events. The cro1-1 mutation thus provides evidence that mitotic crossing-over is dependent upon gene products that are not essential for gene conversional events. The cro1-1 mutation also results in enhanced mitotic-chromosomal instability and MATa/MATα cro1-1/cro1-1 mutants are sporulation deficient. These phenotypes indicate that the CRO1 gene modulates mitotic chromosomal integrity and is essential for normal meiosis. The cro1-1 mutant possesses Holliday junction resolvase activity, hence its recombinational defect does not involve failure to execute this putative final recombinational step. 7 refs., 1 fig., 5 tabs

A double-blind randomised cross-over comparison of nabilone and metoclopramide in the control of radiation-induced nausea

International Nuclear Information System (INIS)

Priestman, S.G.; Priestman, T.J.; Canney, P.A.

1987-01-01

Forty patients who were suffering from radiation induced emesis were entered into a prospectively randomised double-blind cross-over study comparing nabilone with metoclopramide. Only patients who had at least five treatments remaining of their planned course of irradiation were randomised, in order to allow an adequate time to monitor the degree of symptom control and any adverse effects of the two drugs. Patient characteristics and the incidence and severity of nausea and vomiting were similar for the two groups. There was no difference in the efficacy of the two drugs but the incidence and severity of adverse reactions was significantly greater in those patients who received nabilone. (author)

Material control system design: Test Bed Nitrate Storage Area (TBNSA)

International Nuclear Information System (INIS)

Clark, G.A.; Da Roza, R.A.; Dunn, D.R.; Sacks, I.J.; Harrison, W.; Huebel, J.G.; Ross, W.N.; Salisbury, J.D.; Sanborn, R.H.; Weissenberger, S.

1978-05-01

This report provides an example of a hypothetical Special Nuclear Material (SNM) Safeguard Material Control and Accounting (MC and A) System which will be used as a subject for the demonstration of the Lawrence Livermore Laboratory MC and A System Evaluation Methodology in January 1978. This methodology is to become a tool in the NRC evaluation of license applicant submittals for Nuclear Fuel Cycle facilities. The starting point for this test bed design was the Allied-General Nuclear Services--Barnwell Nuclear Fuel Plant Reprocessing plant as described in the Final Safety Analysis Report (FSAR), of August 1975. The test bed design effort was limited to providing an SNM safeguard system for the plutonium nitrate storage area of this facility

Feather bedding and childhood asthma associated with house dust mite sensitisation: a randomised controlled trial.

Science.gov (United States)

Glasgow, Nicholas J; Ponsonby, Anne-Louise; Kemp, Andrew; Tovey, Euan; van Asperen, Peter; McKay, Karen; Forbes, Samantha

2011-06-01

Observational studies report inverse associations between the use of feather upper bedding (pillow and/or quilt) and asthma symptoms but there is no randomised controlled trial (RCT) evidence assessing the role of feather upper bedding as a secondary prevention measure. To determine whether, among children not using feather upper bedding, a new feather pillow and feather quilt reduces asthma severity among house dust mite (HDM) sensitised children with asthma over a 1-year period compared with standard dust mite avoidance advice, and giving children a new mite-occlusive mattress cover. RCT. The Calvary Hospital in the Australian Capital Territory and the Children's Hospital at Westmead, Sydney, New South Wales. 197 children with HDM sensitisation and moderate to severe asthma. Intervention New upper bedding duck feather pillow and quilt and a mite-occlusive mattress cover (feather) versus standard care and a mite-occlusive mattress cover (standard). The proportion of children reporting four or more episodes of wheeze in the past year; an episode of speech-limiting wheeze; or one or more episodes of sleep disturbance caused by wheezing; and spirometry with challenge testing. Statistical analysis included multiple logistic and linear regression. No differences between groups were found for primary end points--frequent wheeze (OR 1.51, 95% CI 0.83 to 2.76, p=0.17), speech-limiting wheeze (OR 0.70, 95% CI 0.32 to 1.48, p=0.35), sleep disturbed because of wheezing (OR 1.17, 95% CI 0.64 to 2.13, p=0.61) or for any secondary end points. Secondary analyses indicated the intervention reduced the risk of sleep being disturbed because of wheezing and severe wheeze to a greater extent for children who slept supine. No differences in respiratory symptoms or lung function were observed 1 year after children with moderate-severe asthma and HDM sensitisation were given a mite-occlusive mattress cover and then received either feather upper bedding (pillow and quilt) or standard

Vestibular and Somatosensory Covergence in Postural Equilibrium Control: Insights from Spaceflight and Bed Rest Studies

Science.gov (United States)

Mulavara, A. P.; Batson, C. D.; Buxton, R. E.; Feiveson, A. H.; Kofman, I. S.; Lee, S. M. C.; Miller, C. A.; Peters, B. T.; Phillips, T.; Platts, S. H.;

The thermal denigration in fluid-bed to make uranyl product

International Nuclear Information System (INIS)

Ma Zhenrong; Cui Yulin; Zhu Changbing; Fan Chuanyong; Liu Yanfeng

2010-01-01

Nuclear fuel reprocessing plant used the thermal denigration to high concentration of uranyl nitrate solution in fluid-bed to make uranyl product. First the uranyl nitrate solution were concentrated in evaporator, into 300 gU/L, 600 gU/L, 750 gU/L and 1000 gU/L.When the fluid-bed was in good fluidity state at 320 degree C, the solution was sprayed all over the surface of the fine crystal seeds through the dual-channel air-blast nozzles to make new crystal seed and to make them grow up. The denigration reaction occurred when the internal temperature of the fluid-bed was kept at about 300 degree C by the outside and inside heat apparatus. The product were transported crossing the valve and spiral transfer to pack. The tail gas was purified and discharged. Through the fluid-bed's running, the variation discipline of temperature and the pressure, the effect curve of the quality of product accumulated to pressure drop were determined. At the same time, the gentrification temperature, the distributed heat and the transfer mode were tested. (authors)

Feather bedding and childhood asthma associated with house dust mite sensitisation : a randomised controlled trial

NARCIS (Netherlands)

Glasgow, Nicholas J.; Ponsonby, Anne-Louise; Kemp, Andrew; Tovey, Euan; van Asperen, Peter; McKay, Karen; Forbes, Samantha

Introduction Observational studies report inverse associations between the use of feather upper bedding (pillow and/or quilt) and asthma symptoms but there is no randomised controlled trial (RCT) evidence assessing the role of feather upper bedding as a secondary prevention measure. Objective To

Bed Load Variability and Morphology of Gravel Bed Rivers Subject to Unsteady Flow: A Laboratory Investigation

Science.gov (United States)

Redolfi, M.; Bertoldi, W.; Tubino, M.; Welber, M.

2018-02-01

Measurement and estimation of bed load transport in gravel bed rivers are highly affected by its temporal fluctuations. Such variability is primarily driven by the flow regime but is also associated with a variety of inherent channel processes, such as flow turbulence, grain entrainment, and bed forms migration. These internal and external controls often act at comparable time scales, and are therefore difficult to disentangle, thus hindering the study of bed load variability under unsteady flow regime. In this paper, we report on laboratory experiments performed in a large, mobile bed flume where typical hydromorphological conditions of gravel bed rivers were reproduced. Data from a large number of replicated runs, including triangular and square-wave hydrographs, were used to build a statistically sound description of sediment transport processes. We found that the inherent variability of bed load flux strongly depends on the sampling interval, and it is significantly higher in complex, wandering or braided channels. This variability can be filtered out by computing the mean response over the experimental replicates, which allows us to highlight two distinctive phenomena: (i) an overshooting (undershooting) response of the mean bed load flux to a sudden increase (decrease) of discharge, and (ii) a clockwise hysteresis in the sediment rating curve. We then provide an interpretation of these findings through a conceptual mathematical model, showing how both phenomena are associated with a lagging morphological adaptation to unsteady flow. Overall, this work provides basic information for evaluating, monitoring, and managing gravel transport in morphologically active rivers.

The effects of a newsletter on bedding control on house dust mite allergen concentrations in childcare centers in Korea

Directory of Open Access Journals (Sweden)

Jeonghoon Kim

2015-08-01

Full Text Available Objectives Bedding in childcare centers (CCCs can hold house dust mite (HDM allergens. This study examined whether HDM allergen levels can be reduced through the distribution of an educational newsletter on bedding control to parents of CCC children in Korea. Methods All 38 CCCs were measured for Der 1 (sum of Der f 1 and Der p 1 concentrations on classroom floors and bedding before the intervention. Educational newsletters on children’s bedding control were sent to 21 CCCs by mail, and teachers were asked to distribute the newsletters to the parents of the children (intervention group. The remaining 17 CCCs were not sent newsletters (control group. The measurement of Der 1 concentrations in 38 CCCs was repeated after the intervention. Dust samples were collected with a vacuum cleaner and analyzed using enzyme-linked immunosorbent assay methods. Results The Der 1 concentrations on the bedding were significantly higher than those on the floors in 38 CCCs at baseline (p<0.05. Although changes of the Der 1 concentrations for the control group (n=17 were not significant, Der 1 concentrations for the intervention group (n=21 decreased significantly from 2077.9 ng/g dust to 963.5 ng/g dust on the floors and from 3683.9 ng/g dust to 610.4 ng/g dust on bedding (p<0.05. Conclusions The distribution of educational newsletters on bedding control to parents may be an effective means of controlling HDMs in CCCs.

Advanced Photovoltaic Inverter Control Development and Validation in a Controller-Hardware-in-the-Loop Test Bed

Energy Technology Data Exchange (ETDEWEB)

Prabakar, Kumaraguru [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Shirazi, Mariko [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Singh, Akanksha [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Chakraborty, Sudipta [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-11-07

Penetration levels of solar photovoltaic (PV) generation on the electric grid have increased in recent years. In the past, most PV installations have not included grid-support functionalities. But today, standards such as the upcoming revisions to IEEE 1547 recommend grid support and anti-islanding functions-including volt-var, frequency-watt, volt-watt, frequency/voltage ride-through, and other inverter functions. These functions allow for the standardized interconnection of distributed energy resources into the grid. This paper develops and tests low-level inverter current control and high-level grid support functions. The controller was developed to integrate advanced inverter functions in a systematic approach, thus avoiding conflict among the different control objectives. The algorithms were then programmed on an off-the-shelf, embedded controller with a dual-core computer processing unit and field-programmable gate array (FPGA). This programmed controller was tested using a controller-hardware-in-the-loop (CHIL) test bed setup using an FPGA-based real-time simulator. The CHIL was run at a time step of 500 ns to accommodate the 20-kHz switching frequency of the developed controller. The details of the advanced control function and CHIL test bed provided here will aide future researchers when designing, implementing, and testing advanced functions of PV inverters.

Reynolds Number Effect on Spatial Development of Viscous Flow Induced by Wave Propagation Over Bed Ripples

Science.gov (United States)

Dimas, Athanassios A.; Kolokythas, Gerasimos A.

Numerical simulations of the free-surface flow, developing by the propagation of nonlinear water waves over a rippled bottom, are performed assuming that the corresponding flow is two-dimensional, incompressible and viscous. The simulations are based on the numerical solution of the Navier-Stokes equations subject to the fully-nonlinear free-surface boundary conditions and appropriate bottom, inflow and outflow boundary conditions. The equations are properly transformed so that the computational domain becomes time-independent. For the spatial discretization, a hybrid scheme is used where central finite-differences, in the horizontal direction, and a pseudo-spectral approximation method with Chebyshev polynomials, in the vertical direction, are applied. A fractional time-step scheme is used for the temporal discretization. Over the rippled bed, the wave boundary layer thickness increases significantly, in comparison to the one over flat bed, due to flow separation at the ripple crests, which generates alternating circulation regions. The amplitude of the wall shear stress over the ripples increases with increasing ripple height or decreasing Reynolds number, while the corresponding friction force is insensitive to the ripple height change. The amplitude of the form drag forces due to dynamic and hydrostatic pressures increase with increasing ripple height but is insensitive to the Reynolds number change, therefore, the percentage of friction in the total drag force decreases with increasing ripple height or increasing Reynolds number.

Effects of Bed Rest on Conduction Velocity of the Triceps Surae Stretch Reflex and Postural Control

Science.gov (United States)

Reschke, M. F.; Wood, S. J.; Cerisano, J. M.; Kofman, I. S.; Fisher, E. A.; Esteves, J. T.; Taylor, L. C.; DeDios, Y. E.; Harm, D. L.

2011-01-01

Despite rigorous exercise and nutritional management during space missions, astronauts returning from microgravity exhibit neuromuscular deficits and a significant loss in muscle mass in the postural muscles of the lower leg. Similar changes in the postural muscles occur in subjects participating in long-duration bed rest studies. These adaptive muscle changes manifest as a reduction in reflex conduction velocity during head-down bed rest. Because the stretch reflex encompasses both the peripheral (muscle spindle and nerve axon) and central (spinal synapse) components involved in adaptation to calf muscle unloading, it may be used to provide feedback on the general condition of neuromuscular function, and might be used to evaluate the effectiveness of countermeasures aimed at preserving muscle mass and function during periods of unloading. Stretch reflexes were measured on 18 control subjects who spent 60 to 90 days in continuous 6 deg head-down bed rest. Using a motorized system capable of rotating the foot around the ankle joint (dorsiflexion) through an angle of 10 degrees at a peak velocity of about 250 deg/sec, a stretch reflex was recorded from the subject's left triceps surae muscle group. Using surface electromyography, about 300 reflex responses were obtained and ensemble-averaged on 3 separate days before bed rest, 3 to 4 times in bed, and 3 times after bed rest. The averaged responses for each test day were examined for reflex latency and conduction velocity (CV) across gender. Computerized posturography was also conducted on these same subjects before and after bed rest as part of the standard measures. Peak-to-peak sway was measured during Sensory Organization Tests (SOTs) to evaluate changes in the ability to effectively use or suppress visual, vestibular, and proprioceptive information for postural control. Although no gender differences were found, a significant increase in reflex latency and a significant decrease in CV were observed during the bed

Near-infrared spectroscopy monitoring and control of the fluidized bed granulation and coating processes-A review.

Science.gov (United States)

Liu, Ronghua; Li, Lian; Yin, Wenping; Xu, Dongbo; Zang, Hengchang

2017-09-15

The fluidized bed granulation and pellets coating technologies are widely used in pharmaceutical industry, because the particles made in a fluidized bed have good flowability, compressibility, and the coating thickness of pellets are homogeneous. With the popularization of process analytical technology (PAT), real-time analysis for critical quality attributes (CQA) was getting more attention. Near-infrared (NIR) spectroscopy, as a PAT tool, could realize the real-time monitoring and control during the granulating and coating processes, which could optimize the manufacturing processes. This article reviewed the application of NIR spectroscopy in CQA (moisture content, particle size and tablet/pellet thickness) monitoring during fluidized bed granulation and coating processes. Through this review, we would like to provide references for realizing automated control and intelligent production in fluidized bed granulation and pellets coating of pharmaceutical industry. Copyright © 2017 Elsevier B.V. All rights reserved.

Does Bedding Affect the Airway and Allergy?

Directory of Open Access Journals (Sweden)

RW Siebers

2011-03-01

Full Text Available Various cross-sectional and longitudinal studies have suggested that synthetic bedding is associated with asthma, allergic rhinitis and eczema while feather bedding seems to be protective. Synthetic bedding items have higher house dust mite allergen levels than feather bedding items. This is possibly the mechanism involved although fungal and bacterial proinflammatory compounds and volatile organic compounds may play a role. In this review we present and discuss the epidemiological evidence and suggest possible mechanisms. Primary intervention studies are required to show whether feather bedding is protective for the development of childhood asthma and allergic diseases while secondary intervention studies are required to potentially reduce symptoms and medication use in subjects with established disease.

Does bedding affect the airway and allergy?

Science.gov (United States)

Siebers, R W; Crane, J

2011-04-01

Various cross-sectional and longitudinal studies have suggested that synthetic bedding is associated with asthma, allergic rhinitis and eczema while feather bedding seems to be protective. Synthetic bedding items have higher house dust mite allergen levels than feather bedding items. This is possibly the mechanism involved although fungal and bacterial proinflammatory compounds and volatile organic compounds may play a role. In this review we present and discuss the epidemiological evidence and suggest possible mechanisms. Primary intervention studies are required to show whether feather bedding is protective for the development of childhood asthma and allergic diseases while secondary intervention studies are required to potentially reduce symptoms and medication use in subjects with established disease.

Biomass fueled fluidized bed combustion: atmospheric emissions, emission control devices and environmental regulations

International Nuclear Information System (INIS)

Grass, S.W.; Jenkins, B.M.

1994-01-01

Fluidized bed combustors have become the technological choice for power generation from biomass fuels in California. Atmospheric emission data obtained during compliance tests are compared for five operating 18 to 32 MW fluidized bed combustion power plants. The discussion focuses on the impact of fuel properties and boiler design criteria on the emission of pollutants, the efficiency of pollution control devices, and regulations affecting atmospheric emissions. Stack NO x emission factors are shown not to vary substantially among the five plants which burn fuels with nitrogen concentrations between 0.3 and 1.1% dry weight. All facilities use at least one particular control device, but not all use limestone injection or other control techniques for sulfur and chlorine. The lack of control for chlorine suggests the potential for emission of toxic species due to favorable temperature conditions existing in the particulate control devices, particularly when burning fuels containing high concentrations of chlorine. (Author)

Development of a Torque Sensor-Based Test Bed for Attitude Control System Verification and Validation

Science.gov (United States)

2017-12-30

AFRL-RV-PS- AFRL-RV-PS- TR-2018-0008 TR-2018-0008 DEVELOPMENT OF A TORQUE SENSOR- BASED TEST BED FOR ATTITUDE CONTROL SYSTEM VERIFICATION AND...Sensor-Based Test Bed for Attitude Control System Verification & Validation 5a. CONTRACT NUMBER FA9453-15-1-0315 5b. GRANT NUMBER 5c. PROGRAM ELEMENT...NUMBER 62601F 6. AUTHOR(S) Norman Fitz-Coy 5d. PROJECT NUMBER 4846 5e. TASK NUMBER PPM00015968 5f. WORK UNIT NUMBER EF125135 7. PERFORMING

[Pathological overeating--an overview].

Science.gov (United States)

Götestam, K Gunnar; Skårderud, Finn; Rosenvinge, Jan H; Vedul-Kjelsås, Einar

2004-08-26

An eating disorder apart from anorexia nervosa and bulimia nervosa is "binge eating disorder" (BED): eating in a short period of time a large quantity of food and a feeling of lack of control over food intake. There is also an atypical rest category, "eating disorders not otherwise specified" (EDNOS). Diagnostic criteria for BED and EDNOS are incomplete, particularly with respect to the definition of "bingeing" relative to bulimia nervosa. More restrictive criteria for anorexia nervosa and bulimia nervosa skew the diagnostic distribution towards BED and EDNOS, though the total prevalence of eating disorders remains unchanged. For BED and EDNOS taken together the lifetime prevalence in women is about 6%. The relationship between BED, EDNOS and overweight has mainly been overlooked; further investigations are needed. Lasting treatment effects have been found for overweight people with BED. Other eating disorders apart from anorexia nervosa and bulimia are prevalent and clinically important, and research has opened up a potential for effective treatment.

Controlling HIV Epidemics among Injection Drug Users: Eight Years of Cross-Border HIV Prevention Interventions in Vietnam and China

Science.gov (United States)

Hammett, Theodore M.; Des Jarlais, Don C.; Kling, Ryan; Kieu, Binh Thanh; McNicholl, Janet M.; Wasinrapee, Punneeporn; McDougal, J. Stephen; Liu, Wei; Chen, Yi; Meng, Donghua; Huu Nguyen, Tho; Ngoc Hoang, Quyen; Van Hoang, Tren

2012-01-01

Introduction HIV in Vietnam and Southern China is driven by injection drug use. We have implemented HIV prevention interventions for IDUs since 2002–2003 in Lang Son and Ha Giang Provinces, Vietnam and Ning Ming County (Guangxi), China. Methods Interventions provide peer education and needle/syringe distribution. Evaluation employed serial cross-sectional surveys of IDUs 26 waves from 2002 to 2011, including interviews and HIV testing. Outcomes were HIV risk behaviors, HIV prevalence and incidence. HIV incidence estimation used two methods: 1) among new injectors from prevalence data; and 2) a capture enzyme immunoassay (BED testing) on all HIV+ samples. Results We found significant declines in drug-related risk behaviors and sharp reductions in HIV prevalence among IDUs (Lang Son from 46% to 23% [pHIV incidence to low levels among new injectors through 36–48 months, then some rebound, particularly in Ning Ming, but BED-based estimates revealed significant reductions in incidence through 96 months. Discussion This is one of the longest studies of HIV prevention among IDUs in Asia. The rebound in incidence among new injectors may reflect sexual transmission. BED-based estimates may overstate incidence (because of false-recent results in patients with long-term infection or on ARV treatment) but adjustment for false-recent results and survey responses on duration of infection generally confirm BED-based incidence trends. Combined trends from the two estimation methods show sharp declines in incidence to low levels. The significant downward trends in all primary outcome measures indicate that the Cross-Border interventions played an important role in bringing HIV epidemics among IDUs under control. The Cross-Border project offers a model of HIV prevention for IDUs that should be considered for large-scale replication. PMID:22952640

Control, data acquisition and analysis for the JET neutral injection test bed

International Nuclear Information System (INIS)

Jones, T.T.C.; Brenan, P.R.; Rodgers, M.E.; Stork, D.; Young, I.D.

1985-01-01

The Neutral Injection Test-Bed (NITB) is a major experimental assembly in support of the Neutral Beam Heating Programme for JET. In addition to its prime function of testing the Neutral Injection hardware, the Test Bed serves as the prototype to test the computer control and data acquisition system, which is described in this paper. The software system has been written in a portable, data-driven manner with the aim to adapt it, with only minor modifications to the operation of the first. Neutral Injection Beamline on JET, which will involve operation both synchronous and asynchronous with that of the JET Tokamak

ADVANCES IN CLOG STATE MONITORING FOR USE IN AUTOMATED REED BED INSTALLATIONS

Directory of Open Access Journals (Sweden)

Theodore HUGHES-RILEY

2014-06-01

Full Text Available Constructed wetlands are a popular form of waste-water treatment that have proliferated across Europe and the rest of the world in recent years as an environmentally conscious form of waste water treatment. The ability to monitor the conditions in the bed and control input factors such as heating and aeration may extend the lifetime of the reed bed substantially beyond the ten year lifetime normally reached. The Autonomous Reed Bed Installation (ARBI project is an EU FP7 initiative to develop a reed bed with automated control over input parameters based on readings taken from embedded sensors. Automated remedial action may improve bed treatment efficiency, and prolong the life of the bed and avoiding the need to refurbish the bed, which is both time consuming and costly. One critical parameter to observe is the clog state of the reed bed, as this can severely impact on the efficiency of water treatment to the point of the bed becoming non-operable. Magnetic resonance (MR sensors can be a powerful tool in determining clogging levels, and has previously been explored in the literature. This work is based on a conference paper (2nd International Conference "Water resources and wetlands", 2014 and details magnetic sensors suitable for long-term embedding into a constructed wetland. Unlike previous studies this work examines a probe embedded into a wetland.

Effect of β-hydroxy-β-methylbutyrate (HMB) on lean body mass during 10 days of bed rest in older adults.

Science.gov (United States)

Deutz, Nicolaas E P; Pereira, Suzette L; Hays, Nicholas P; Oliver, Jeffery S; Edens, Neile K; Evans, Chris M; Wolfe, Robert R

2013-10-01

Loss of muscle mass due to prolonged bed rest decreases functional capacity and increases hospital morbidity and mortality in older adults. To determine if HMB, a leucine metabolite, is capable of attenuating muscle decline in healthy older adults during complete bed rest. A randomized, controlled, double-blinded, parallel-group design study was carried out in 24 healthy (SPPB ≥ 9) older adult subjects (20 women, 4 men), confined to complete bed rest for ten days, followed by resistance training rehabilitation for eight weeks. Subjects in the experimental group were treated with HMB (calcium salt, 1.5 g twice daily - total 3 g/day). Control subjects were treated with an inactive placebo powder. Treatments were provided starting 5 days prior to bed rest till the end rehabilitation phase. DXA was used to measure body composition. Nineteen eligible older adults (BMI: 21-33; age: 60-76 year) were evaluable at the end of the bed rest period (Control n = 8; Ca-HMB n = 11). Bed rest caused a significant decrease in total lean body mass (LBM) (2.05 ± 0.66 kg; p = 0.02, paired t-test) in the Control group. With the exclusion of one subject, treatment with HMB prevented the decline in LBM over bed rest -0.17 ± 0.19 kg; p = 0.23, paired t-test). There was a statistically significant difference between treatment groups for change in LBM over bed rest (p = 0.02, ANOVA). Sub-analysis on female subjects (Control = 7, HMB = 8) also revealed a significant difference in change in LBM over bed rest between treatment groups (p = 0.04, ANOVA). However, differences in function parameters could not be observed, probably due to the sample size of the study. In healthy older adults, HMB supplementation preserves muscle mass during 10 days of bed rest. These results need to be confirmed in a larger trial. Copyright © 2013 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

Multiple Property Cross Direction Control of Paper Machines

Directory of Open Access Journals (Sweden)

Markku Ohenoja

2011-07-01

Full Text Available Cross direction (CD control in sheet-forming process forms a challenging problem with high dimensions. Accounting the interactions between different properties and actuators, the dimensionality increases further and also computational issues arise. We present a multiple property controller feasible to be used especially with imaging measurements that provide high sampling frequency and therefore enable short control interval. The simulation results state the benefits of multiple property CD control over single property control and single property control using full feedforward compensation. The controller presented may also be tuned in automated manner and the results demonstrate the effect of tuning on input saturation.

The characteristics of bed agglomeration during fluidized bed combustion of eucalyptus bark

International Nuclear Information System (INIS)

Chaivatamaset, Pawin; Tia, Suvit

2015-01-01

The bed agglomeration behaviors were investigated experimentally when eucalyptus bark was burning tested in a laboratory scale fluidized bed reactor. The focuses of this work were the influences of operating conditions and bed materials on the bed agglomeration tendency and the elucidation in the behaviors of fuel inorganic elements and the governing mode of the agglomeration. It was found that the defluidization caused by the bed agglomeration was clearly detectable from the decrease in measured bed pressure. The growth of bed particle and accumulation of agglomerates during combustion provided the partial to complete defluidization. The defluidization was promoted by the increase of bed temperature and bed particle size, and the decrease of fluidizing air velocity. The SEM-EDS analyses revealed that the bed agglomeration was mainly attributed to the formation of potassium silicate compounds as liquid phase during the combustion. This was initiated by the chemical reaction between the bed particle and the released ash constituents. In this study, the inorganic migration from fuel particle to bed particle was likely dominated by the condensation/reaction. The thermodynamic examination by ternary phase diagram analysis corroborated that the liquid phase formation of the ash derived materials controlled the agglomeration. The alumina sand prevented the bed agglomeration since it was inactive in the formation of viscous molten substances during combustion at the observed temperatures. - Highlights: • The behaviors of bed agglomeration were studied during the fluidized bed combustion of eucalyptus bark. • The increase in bed temperature and sand size, and the decrease of air velocity promoted bed defluidization. • The formation of molten potassium silicate compounds conduced to the bed agglomeration. • Condensation/reaction was the dominant inorganic migration mechanism from fuel particle to bed particle. • The alumina sand prevented effectively the bed

Exploring the role of flood transience in coarse bed load sediment transport

Science.gov (United States)

Phillips, C. B.; Singer, M. B.; Hill, K. M.; Paola, C.

2015-12-01

The rate of bed load transport under steady flow is known to vary both spatially and temporally due to various hydrologic and granular phenomena. Grain size distributions and riverbed properties (packing, imbrication, etc.) are known to affect flux for a particular value of applied flow stress, while hydrology is mainly assumed to control the magnitude of the applied bed stress above the threshold for bed material entrainment. The prediction of bed load sediment transport in field settings is further complicated by the inherent transience in flood hydrology, but little is known about how such flood transience influences bed load flux over a range of applied bed stress. Here we investigate the role of flood transience for gravel bed load transport through controlled laboratory experiments in a 28 m long 0.5 meter wide flume. We explore transient flow as the combination of unsteady and intermittent flow, where unsteady flow varies in magnitude over a given duration, and intermittent flow is characterized by turning the flow on and off. We systematically vary these details of flood hydrographs from one experiment to the next, and monitor the bed load as it varies with water discharge in real time by measuring sediment flux and tracking particles. We find that even with a narrow unimodal grain size distribution and constant sediment supply we observe hysteresis in bed load flux, different thresholds for entrainment and distrainment for the rising and falling limbs of a flood, and a threshold of entrainment that can vary one flood hydrograph to the next. Despite these complex phenomena we find that the total bed load transported for each flood plots along a linear trend with the integrated excess stress, consistent with prior field results. These results suggest that while the effects of transient flow and the shape of the hydrograph are measurable, they are second-order compared to the integrated excess stress.

Determination of pressure distribution in an aerated bed in a controlled pilot-scale compost reactor

Energy Technology Data Exchange (ETDEWEB)

Solowiej, P. [Warmia and Mazury Univ., Olsztyn (Poland)

2010-07-01

This study investigated the effectiveness of dealing with biological waste by composting. In particular, it examined the feasibility of recovering excess thermal energy produced in the process of composting biological waste in terms of mass and energy transport parameters required in the aerated compost bed. An experiment was performed in which a 100 dm{sup 3} adiabatic, leak-tight reactor equipped with a controlled aeration system was constructed to study the temperature and pressure distribution in the bed. Sensors were used to determine the amount and humidity of emitted gases under variable external physical conditions. The perforated bottom of the reactor allowed for bed aeration. As such, the humidity and heat were transported upwards, forced by the air pumped in and by natural convection. In terms of pressure distribution inside the composted and aerated bed, the study results showed that there were considerable differences in pressure for the selected places of the bed of the composted biological material. An increase in upwards pressure was observed in the heap throughout the experiment. Pressure differences in the same plane of the bed were also noted. The study results should facilitate the development of a model of mass and energy transport in a bed of composted material.

The anticonvulsant levetiracetam for the treatment of pain in polyneuropathy: A randomized, placebo-controlled, cross-over trial

DEFF Research Database (Denmark)

Holbech, Jakob Vormstrup; Otto, Marit; Bach, Flemming W

2011-01-01

of this study was to test the analgesic effect of levetiracetam in painful polyneuropathy. METHODS: This was a randomized, double-blind, placebo-controlled, cross-over trial with levetiracetam 3000mg/day versus placebo (6-week treatment periods). Patients with diagnosed polyneuropathy and symptoms for more than......-three patients were screened for participation and 39 patients entered the study. Thirty-five patients were included in the data analysis. There were no differences in the ratings of pain relief (levetiracetam 2.29 versus placebo 2.28, p=0.979), total pain intensity (levetiracetam 5.5 versus placebo 5.3, p=0......Levetiracetam is an anticonvulsant which is assumed to act by modulating neurotransmitter release via binding to the vesicle protein SV2A. This could have an impact on signaling in the nociceptive system, and a pilot study indicated relief of neuropathic pain with levetiracetam. OBJECTIVES: The aim...

Experimental analysis of methanol cross-over in a direct methanol fuel cell

Energy Technology Data Exchange (ETDEWEB)

Casalegno, Andrea [Dipartimento di Energetica, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milan (Italy)]. E-mail: andrea.casalegno@polimi.it; Grassini, Paolo [Dipartimento di Energetica, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milan (Italy)]. E-mail: PGrassini@seal.it; Marchesi, Renzo [Dipartimento di Energetica, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milan (Italy)]. E-mail: renzo.marchesi@polimi.it

2007-03-15

Methanol cross-over through the polymeric membrane is one of the main causes limiting direct methanol fuel cell performances. It causes fuel wasting and enhances cathode overpotential. A repeatable and reproducible measurement system, that assures the traceability of the measurement to international reference standards, is necessary to compare different fuel cell construction materials. In this work a method to evaluate methanol cross-over rate and operating condition influence is presented and qualified in term of measurement uncertainty. In the investigated range, the methanol cross-over rate results mainly due to diffusion through the membrane, in fact it is strongly affected by temperature. Moreover the cross-over influence on fuel utilization and fuel cell efficiency is investigated. The methanol cross-over rate appears linearly proportional to electrochemical fuel utilization and values, obtained by measurements at different anode flow rate but constant electrochemical fuel utilization, are roughly equal; methanol wasting, due to cross-over, is considerable and can still be higher than electrochemical utilization. The fuel recirculation effect on energy efficiency has been investigated and it was found that fuel recirculation gives more advantage at low temperature, but fuel cell energy efficiency results are in any event higher at high temperature.

Experimental analysis of methanol cross-over in a direct methanol fuel cell

International Nuclear Information System (INIS)

Casalegno, Andrea; Grassini, Paolo; Marchesi, Renzo

2007-01-01

Methanol cross-over through the polymeric membrane is one of the main causes limiting direct methanol fuel cell performances. It causes fuel wasting and enhances cathode overpotential. A repeatable and reproducible measurement system, that assures the traceability of the measurement to international reference standards, is necessary to compare different fuel cell construction materials. In this work a method to evaluate methanol cross-over rate and operating condition influence is presented and qualified in term of measurement uncertainty. In the investigated range, the methanol cross-over rate results mainly due to diffusion through the membrane, in fact it is strongly affected by temperature. Moreover the cross-over influence on fuel utilization and fuel cell efficiency is investigated. The methanol cross-over rate appears linearly proportional to electrochemical fuel utilization and values, obtained by measurements at different anode flow rate but constant electrochemical fuel utilization, are roughly equal; methanol wasting, due to cross-over, is considerable and can still be higher than electrochemical utilization. The fuel recirculation effect on energy efficiency has been investigated and it was found that fuel recirculation gives more advantage at low temperature, but fuel cell energy efficiency results are in any event higher at high temperature

Concentration profiles in the wake of a sphere buried in a granular bed through which fluid flows

International Nuclear Information System (INIS)

Guedes de Carvalho, J.R.F.; Delgado, J.M.P.Q.; Alves, M.A.

2005-01-01

The concentration distribution in the wake of a soluble sphere immersed in a granular bed of inerts has been obtained numerically, for transport by both advection and diffusion/dispersion. Fluid flow in the granular bed around the sphere was assumed to follow Darcy's law and, at each point, dispersion of solute was considered in both the cross-stream and stream-wise directions. The elliptic PDE equation, resulting from a differential material balance on the solute, has been solved numerically over a wide range of values of the relevant parameters. (authors)

Concentration profiles in the wake of a sphere buried in a granular bed through which fluid flows

Energy Technology Data Exchange (ETDEWEB)

Guedes de Carvalho, J.R.F.; Delgado, J.M.P.Q.; Alves, M.A. [Porto Univ., Dpet. de Engenharia Quimica, Faculdade de Engenharia (Portugal)

2005-07-01

The concentration distribution in the wake of a soluble sphere immersed in a granular bed of inerts has been obtained numerically, for transport by both advection and diffusion/dispersion. Fluid flow in the granular bed around the sphere was assumed to follow Darcy's law and, at each point, dispersion of solute was considered in both the cross-stream and stream-wise directions. The elliptic PDE equation, resulting from a differential material balance on the solute, has been solved numerically over a wide range of values of the relevant parameters. (authors)

Reactivity control system of a passively safe thorium breeder pebble bed reactor

International Nuclear Information System (INIS)

Wols, F.J.; Kloosterman, J.L.; Lathouwers, D.; Hagen, T.H.J.J. van der

2014-01-01

Highlights: • A worth of over 15,000 pcm ensures achieving long-term cold shutdown in thorium PBR. • Control rod worth in side reflector is insufficient due to low-power breeder zone. • 20 control rods, just outside the driver zone, can achieve long-term cold shutdown. • BF 3 gas can be inserted for reactor shutdown, but only in case of emergency. • Perturbation theory accurately predicts absorber gas worth for many concentrations. - Abstract: This work investigates the neutronic design of the reactivity control system for a 100 MW th passively safe thorium breeder pebble bed reactor (PBR), a conceptual design introduced previously by the authors. The thorium PBR consists of a central driver zone of 100 cm radius, surrounded by a breeder zone with 300 cm outer radius. The fissile content of the breeder zone is low, leading to low fluxes in the radial reflector region. Therefore, a significant decrease of the control rod worth at this position is anticipated. The reactivity worth of control rods in the side reflector and at alternative in-core positions is calculated using different techniques, being 2D neutron diffusion, perturbation theory and more accurate 3D Monte Carlo models. Sensitivity coefficients from perturbation theory provide a first indication of effective control rod positions, while the 2D diffusion models provide an upper limit on the reactivity worth achievable at a certain radial position due to the homogeneous spreading of the absorber material over the azimuthal domain. Three dimensional forward calculations, e.g. in KENO, are needed for an accurate calculation of the total control rod worth. The two dimensional homogeneous calculations indicate that the reactivity worth in the radial reflector is by far insufficient to achieve cold reactor shutdown, which requires a control rod worth of over 15 000 pcm. Three dimensional heterogeneous KENO calculations show that placing 20 control rods just outside the driver channel, between 100 cm

Reactivity control system of a passively safe thorium breeder pebble bed reactor

Energy Technology Data Exchange (ETDEWEB)

Wols, F.J., E-mail: f.j.wols@tudelft.nl; Kloosterman, J.L.; Lathouwers, D.; Hagen, T.H.J.J. van der

2014-12-15

Highlights: • A worth of over 15,000 pcm ensures achieving long-term cold shutdown in thorium PBR. • Control rod worth in side reflector is insufficient due to low-power breeder zone. • 20 control rods, just outside the driver zone, can achieve long-term cold shutdown. • BF{sub 3} gas can be inserted for reactor shutdown, but only in case of emergency. • Perturbation theory accurately predicts absorber gas worth for many concentrations. - Abstract: This work investigates the neutronic design of the reactivity control system for a 100 MW{sub th} passively safe thorium breeder pebble bed reactor (PBR), a conceptual design introduced previously by the authors. The thorium PBR consists of a central driver zone of 100 cm radius, surrounded by a breeder zone with 300 cm outer radius. The fissile content of the breeder zone is low, leading to low fluxes in the radial reflector region. Therefore, a significant decrease of the control rod worth at this position is anticipated. The reactivity worth of control rods in the side reflector and at alternative in-core positions is calculated using different techniques, being 2D neutron diffusion, perturbation theory and more accurate 3D Monte Carlo models. Sensitivity coefficients from perturbation theory provide a first indication of effective control rod positions, while the 2D diffusion models provide an upper limit on the reactivity worth achievable at a certain radial position due to the homogeneous spreading of the absorber material over the azimuthal domain. Three dimensional forward calculations, e.g. in KENO, are needed for an accurate calculation of the total control rod worth. The two dimensional homogeneous calculations indicate that the reactivity worth in the radial reflector is by far insufficient to achieve cold reactor shutdown, which requires a control rod worth of over 15 000 pcm. Three dimensional heterogeneous KENO calculations show that placing 20 control rods just outside the driver channel

Impaired anticipatory control of grasp during obstacle crossing in Parkinson's disease.

Science.gov (United States)

McIsaac, Tara L; Diermayr, Gudrun; Albert, Frederic

2012-05-16

During self-paced walking, people with Parkinson's disease maintain anticipatory control during object grasping. However, common functional tasks often include carrying an object while changing step patterns mid-path and maneuvering over obstacles, increasing task complexity and attentional demands. Thus, the present study investigated the effect of Parkinson's disease on the modulation of grasping force changes as a function of gait-related inertial forces. Subjects with Parkinson's disease maintained the ability to scale and to couple over time their grip and inertial forces while walking at irregular step lengths, but were unable to maintain the temporal coupling of grasping forces compared to controls during obstacle crossing. We suggest that this deterioration in anticipatory control is associated with the increased demands of task complexity and attention during obstacle crossing. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

BedMachine v3: Complete Bed Topography and Ocean Bathymetry Mapping of Greenland From Multibeam Echo Sounding Combined With Mass Conservation

DEFF Research Database (Denmark)

Morlighem, M.; Williams, C. N.; Rignot, E.

2017-01-01

Greenland's bed topography is a primary control on ice flow, grounding line migration, calving dynamics, and subglacial drainage. Moreover, fjord bathymetry regulates the penetration of warm Atlantic water (AW) that rapidly melts and undercuts Greenland's marine‐terminating glaciers. Here we...... present a new compilation of Greenland bed topography that assimilates seafloor bathymetry and ice thickness data through a mass conservation approach. A new 150 m horizontal resolution bed topography/bathymetric map of Greenland is constructed with seamless transitions at the ice/ocean interface......, yielding major improvements over previous data sets, particularly in the marine‐terminating sectors of northwest and southeast Greenland. Our map reveals that the total sea level potential of the Greenland ice sheet is 7.42 ± 0.05 m, which is 7 cm greater than previous estimates. Furthermore, it explains...

Generation of Composite Dose and Biological Effective Dose (BED) Over Multiple Treatment Modalities and Multistage Planning Using Deformable Image Registration

International Nuclear Information System (INIS)

Zhang, Geoffrey; Huang, T-C; Feygelman, Vladimir; Stevens, Craig; Forster, Kenneth

2010-01-01

Currently there are no commercially available tools to generate composite plans across different treatment modalities and/or different planning image sets. Without a composite plan, it may be difficult to perform a meaningful dosimetric evaluation of the overall treatment course. In this paper, we introduce a method to generate composite biological effective dose (BED) plans over multiple radiotherapy treatment modalities and/or multistage plans, using deformable image registration. Two cases were used to demonstrate the method. Case I was prostate cancer treated with intensity-modulated radiation therapy (IMRT) and a permanent seed implant. Case II involved lung cancer treated with two treatment plans generated on two separate computed tomography image sets. Thin-plate spline or optical flow methods were used as appropriate to generate deformation matrices. The deformation matrices were then applied to the dose matrices and the resulting physical doses were converted to BED and added to yield the composite plan. Cell proliferation and sublethal repair were considered in the BED calculations. The difference in BED between normal tissues and tumor volumes was accounted for by using different BED models, α/β values, and cell potential doubling times. The method to generate composite BED plans presented in this paper provides information not available with the traditional simple dose summation or physical dose summation. With the understanding of limitations and uncertainties of the algorithms involved, it may be valuable for the overall treatment plan evaluation.

Modelling heat transfer during flow through a random packed bed of spheres

Science.gov (United States)

Burström, Per E. C.; Frishfelds, Vilnis; Ljung, Anna-Lena; Lundström, T. Staffan; Marjavaara, B. Daniel

2018-04-01

Heat transfer in a random packed bed of monosized iron ore pellets is modelled with both a discrete three-dimensional system of spheres and a continuous Computational Fluid Dynamics (CFD) model. Results show a good agreement between the two models for average values over a cross section of the bed for an even temperature profiles at the inlet. The advantage with the discrete model is that it captures local effects such as decreased heat transfer in sections with low speed. The disadvantage is that it is computationally heavy for larger systems of pellets. If averaged values are sufficient, the CFD model is an attractive alternative that is easy to couple to the physics up- and downstream the packed bed. The good agreement between the discrete and continuous model furthermore indicates that the discrete model may be used also on non-Stokian flow in the transitional region between laminar and turbulent flow, as turbulent effects show little influence of the overall heat transfer rates in the continuous model.

The application of quality control circle in neurosurgery ICU nurses in raising compliance of the head of a bed

Directory of Open Access Journals (Sweden)

Na LI

2014-11-01

Full Text Available Objective: To explore the application of quality control circle in raising compliance of the head of a bed in neurosurgery ICU nurses. Methods: The quality control circle was made up of 4 ICU nurses, determine the subject in order to improve the neurosurgery ICU nurses in raising compliance of the head of a bed, according to the QCC activity steps to formulate plans, including grasp the current situation, goal setting, through analysis, circle members develop strategy and plan implementation and review, finally compared the situation before and after neurosurgery ICU nurses raised bed activities compliance. Results: After implementation of QCC, neurosurgery ICU nurses raised bed to 30 ~ 45 degrees. After activities, circle members in the team cooperation ability, cohesion, to accept new things ability, and innovative thinking ability and to raise the understanding of the relevant knowledge of the head of a bed has improved significantly. Conclusion: The application of quality management circle activity improves the neurosurgery ICU nurses effectively raise the compliance of the head of a bed, improve the comprehensive quality of the clinical nurses.

Double-blind, placebo-controlled cross-over study of intravenous S-adenosyl-L-methionine in patients with fibromyalgia

DEFF Research Database (Denmark)

Volkmann, H; Nørregaard, J; Jacobsen, Søren

1997-01-01

The objective of this study was to test the efficacy of intravenously administered S-adenosyl-L-methionine (SAMe) in patients with fibromyalgia (FM). Thirty-four out-patients with fibromyalgia symptoms received SAMe 600 mg i.v. or placebo daily for 10 days in a cross-over trial. There was no sign......The objective of this study was to test the efficacy of intravenously administered S-adenosyl-L-methionine (SAMe) in patients with fibromyalgia (FM). Thirty-four out-patients with fibromyalgia symptoms received SAMe 600 mg i.v. or placebo daily for 10 days in a cross-over trial.......17) and slight improvement only on fatigue, quality of sleep, morning stiffness, and on the Fibromyalgia Impact Questionnaire for pain. No effect could be observed on isokinetic muscle strength, Zerrsen self-assessment questionnaire, and the face scale. No effect of SAMe in patients with FM was found...

Identification and MPC control of a circulation fluidized bed boiler using an LPV model

NARCIS (Netherlands)

Huang, J.; Ji, G.; Zhu, Y.; Lin, W.; Kothare, M.; Tade, M.; Vande Wouwer, A.; Smets, I.

2010-01-01

This work studies the identification and control of circulation fluidized bed (CFB) boilers. The CFB boiler under investigation shows strong nonlinearity due to big changes of steam load. A linear parameter varying (LPV) model is used to represent the process dynamics and used in control. The steam

Arthroscopy or ultrasound in undergraduate anatomy education: a randomized cross-over controlled trial

Science.gov (United States)

2012-01-01

Background The exponential growth of image-based diagnostic and minimally invasive interventions requires a detailed three-dimensional anatomical knowledge and increases the demand towards the undergraduate anatomical curriculum. This randomized controlled trial investigates whether musculoskeletal ultrasound (MSUS) or arthroscopic methods can increase the anatomical knowledge uptake. Methods Second-year medical students were randomly allocated to three groups. In addition to the compulsory dissection course, the ultrasound group (MSUS) was taught by eight, didactically and professionally trained, experienced student-teachers and the arthroscopy group (ASK) was taught by eight experienced physicians. The control group (CON) acquired the anatomical knowledge only via the dissection course. Exposure (MSUS and ASK) took place in two separate lessons (75 minutes each, shoulder and knee joint) and introduced standard scan planes using a 10-MHz ultrasound system as well as arthroscopy tutorials at a simulator combined with video tutorials. The theoretical anatomic learning outcomes were tested using a multiple-choice questionnaire (MCQ), and after cross-over an objective structured clinical examination (OSCE). Differences in student’s perceptions were evaluated using Likert scale-based items. Results The ASK-group (n = 70, age 23.4 (20–36) yrs.) performed moderately better in the anatomical MC exam in comparison to the MSUS-group (n = 84, age 24.2 (20–53) yrs.) and the CON-group (n = 88, 22.8 (20–33) yrs.; p = 0.019). After an additional arthroscopy teaching 1% of students failed the MC exam, in contrast to 10% in the MSUS- or CON-group, respectively. The benefit of the ASK module was limited to the shoulder area (p training is profitable and attractive to students with respect to complex joint anatomy. Simultaneous teaching of basic-skills in musculoskeletal ultrasound should be performed by medical experts, but seems to be inferior to the arthroscopic 2D-3D

Discussion on the differences between epigenetic oxidized and primary red beds

International Nuclear Information System (INIS)

Chen Xiaolin; Fang Xiheng; Sun Ye; Pang Yaqing; Guo Qingyin

2008-01-01

The red oxidation zone may be formed in the process of the interlayer oxidation. If the original gray beds formed in the moist palaeoclimatic condition and became red in oxidation, it is easy to distinguish this red oxidization zone from the original red beds. Gray sandstone sandwiched by red mudstone can be formed partially in the arid-semiarid condition. If this gray sandstone was oxidized to be red in color, almost all the strata would be red in cross section, and then it will be difficult to distinguish these red strata from the original red beds. If they are regarded as original red beds, we maybe lose the favorable opportunity to find uranium deposit. This paper presents a case study of Yaojia Formation, Upper Cretaceous in the southwestern part of Songliao Basin. Although the palaeoelimatic condition was arid-semiarid, the gray sandstones of Yaojia Formation in Qianjiadian Sag and its adjacent areas have obvious characteristics of primary depositional origin, and part of them may be formed by epigenetic reduction. The gray sandstone has formed red interlayer oxidation zone after being oxidized and it is just the red interlayer oxidation zone which controls the uranium mineralization in Qianjiadian uranium deposit. By careful contrast and analysis, identification marks of red epigenetic oxidation beds have be established, which can effectively help the distinguishing of epigenetic oxidized red beds from original red beds and extends prospecting idea. (authors)

Long-Term Efficacy of Various Natural or "Green" Insecticides against Bed Bugs: A Double-Blind Study.

Science.gov (United States)

Goddard, Jerome

2014-11-28

Bed bugs are resurging throughout the world, and, thus, effective pest control strategies are constantly needed. A few studies have evaluated 25(b) and other natural, or so-called "green" products, as well as over-the-counter insecticides for bed bugs, but additional studies are needed to determine efficacy of bed bug control products. This double-blinded research project was initiated to examine long-term effectiveness of six commercially available natural or "green" insecticides against bed bugs and to compare them with three known traditional residual products. Water was used as a control. Products were evaluated against both susceptible and resistant strains of bed bugs (1200 bugs each), and two different substrates were used. Temprid(®) (Bayer Corporation, Monheim, Germany), Transport(®) (FMC Corp., Philadelphia, PA, USA), Invader(®) (FMC Corporation, Philadelphia, PA USA), Cimexa(®) (Rockwell Laboratories, Kansas City, MO, USA), and BBT-2000(®) (Swepe-Tite LLC, Tupelo, MS, USA) were the only products which showed any substantial (>40%) bed bug control upon exposure to treated substrates after the six-month waiting period, although results with the resistant bed bug strain were much reduced. Alpine dust(®) (BASF Corporation, Florham Park, NJ, USA) killed 27% of bed bugs or less, depending on strain and substrate. EcoRaider(®) (North Bergen, NJ, USA) and Mother Earth D(®) (Whitmire Microgen, Florham Park, NJ, USA) (diatomaceous earth) produced 11% control or less. Cimi-Shield Protect(®) (Pest Barrier, Carson, CA, USA) showed no activity against bed bugs in this study. Analysis using SAS software showed a three-way interaction between treatment, substrate, and bed bug strain (Numerator DF 9; Denominator DF 80; F = 4.90; p < 0.0001).

Design and control of the precise tracking bed based on complex electromechanical design theory

Science.gov (United States)

Ren, Changzhi; Liu, Zhao; Wu, Liao; Chen, Ken

2010-05-01

The precise tracking technology is wide used in astronomical instruments, satellite tracking and aeronautic test bed. However, the precise ultra low speed tracking drive system is one high integrated electromechanical system, which one complexly electromechanical design method is adopted to improve the efficiency, reliability and quality of the system during the design and manufacture circle. The precise Tracking Bed is one ultra-exact, ultra-low speed, high precision and huge inertial instrument, which some kind of mechanism and environment of the ultra low speed is different from general technology. This paper explores the design process based on complex electromechanical optimizing design theory, one non-PID with a CMAC forward feedback control method is used in the servo system of the precise tracking bed and some simulation results are discussed.

SPECIFIC AND CROSS-OVER EFFECTS OF FOAM ROLLING ON ANKLE DORSIFLEXION RANGE OF MOTION

Science.gov (United States)

Beardsley, Chris

2016-01-01

ABSTRACT Background Flexibility is an important physical quality. Self-myofascial release (SMFR) methods such as foam rolling (FR) increase flexibility acutely but how long such increases in range of motion (ROM) last is unclear. Static stretching (SS) also increases flexibility acutely and produces a cross-over effect to contralateral limbs. FR may also produce a cross-over effect to contralateral limbs but this has not yet been identified. Purpose To explore the potential cross-over effect of SMFR by investigating the effects of a FR treatment on the ipsilateral limb of 3 bouts of 30 seconds on changes in ipsilateral and contralateral ankle DF ROM and to assess the time-course of those effects up to 20 minutes post-treatment. Methods A within- and between-subject design was carried out in a convenience sample of 26 subjects, allocated into FR (n=13) and control (CON, n=13) groups. Ankle DF ROM was recorded at baseline with the in-line weight-bearing lunge test for both ipsilateral and contralateral legs and at 0, 5, 10, 15, 20 minutes following either a two-minute seated rest (CON) or 3 3 30 seconds of FR of the plantar flexors of the dominant leg (FR). Repeated measures ANOVA was used to examine differences in ankle DF ROM. Results No significant between-group effect was seen following the intervention. However, a significant within-group effect (pin the FR group was seen between baseline and all post-treatment time-points (0, 5, 10, 15 and 20 minutes). Significant within-group effects (pin the ipsilateral leg between baseline and at all post-treatment time-points, and in the contralateral leg up to 10 minutes post-treatment, indicating the presence of a cross-over effect. Conclusions FR improves ankle DF ROM for at least 20 minutes in the ipsilateral limb and up to 10 minutes in the contralateral limb, indicating that FR produces a cross-over effect into the contralateral limb. The mechanism producing these cross-over effects is unclear but may involve

Children of parents with BED have more eating behavior disturbance than children of parents with obesity or healthy weight.

Science.gov (United States)

Lydecker, Janet A; Grilo, Carlos M

2017-06-01

A limited literature suggests an association between parental eating disorders and child eating-disorder behaviors although this research has focused primarily on restrictive-type eating disorders and very little is known about families with binge-eating disorder (BED). The current study focused on parents (N = 331; 103 fathers and 226 mothers), comparing parents with core features of BED (n = 63) to parents with obesity and no eating disorder (OB; n = 85) and parents with healthy-weight and no eating disorder (HW; n = 183). Parents with BED were significantly more likely than OB and HW parents to report child binge eating, and more likely than HW parents to report child overeating. Parents with BED felt greater responsibility for child feeding than OB parents, and felt more concern about their child's weight than OB and HW parents. Dietary restriction of the child by the parents was related to child binge eating, overeating, and child overweight, and parental group was related to child binge eating (parental BED), overeating (parental BED), and child weight (parental OB). Parents with BED report greater disturbance in their children's eating than OB and HW parents, and OB parents report higher child weight than HW parents. This suggests that it is important to consider both eating-disorder psychopathology and obesity in clinical interventions and research. Our cross-sectional findings, which require experimental and prospective confirmations, provide preliminary evidence suggesting potential factors in families with parental BED and obesity to address in treatment and prevention efforts for pediatric eating disorders and obesity. © 2016 Wiley Periodicals, Inc.(Int J Eat Disord 2017; 50:648-656). © 2016 Wiley Periodicals, Inc.

Fluidized bed catalytic pyrolysis of eucalyptus over hzsm-5: effect of acid density and gallium modification on catalyst deactivation

Science.gov (United States)

Catalytic fast pyrolysis of eucalyptus wood was performed on a continuous laboratory scale fluidized bed fast pyrolysis system. Catalytic activity was monitored from use of fresh catalyst up to a cumulative biomass to catalyst ratio (B/C) of 4/1 over extruded pellets of three different ZSM-5 catalys...

Intracycle angular velocity control of cross-flow turbines

Science.gov (United States)

Strom, Benjamin; Brunton, Steven L.; Polagye, Brian

2017-08-01

Cross-flow turbines, also known as vertical-axis turbines, are attractive for power generation from wind and water currents. Some cross-flow turbine designs optimize unsteady fluid forces and maximize power output by controlling blade kinematics within one rotation. One established method is to dynamically pitch the blades. Here we introduce a mechanically simpler alternative: optimize the turbine rotation rate as a function of angular blade position. We demonstrate experimentally that this approach results in a 59% increase in power output over standard control methods. Analysis of fluid forcing and blade kinematics suggest that power increase is achieved through modification of the local flow conditions and alignment of fluid force and rotation rate extrema. The result is a low-speed, structurally robust turbine that achieves high efficiency and could enable a new generation of environmentally benign turbines for renewable power generation.

Cross-layer ultrasound video streaming over mobile WiMAX and HSUPA networks.

Science.gov (United States)

Alinejad, Ali; Philip, Nada Y; Istepanian, Robert S H

2012-01-01

It is well known that the evolution of 4G-based mobile multimedia network systems will contribute significantly to future mobile healthcare (m-health) applications that require high bandwidth and fast data rates. Central to the success of such emerging applications is the compatibility of broadband networks, such as mobile Worldwide Interoperability For Microwave Access (WiMAX) and High-Speed Uplink Packet Access (HSUPA), and especially their rate adaption issues combined with the acceptable real-time medical quality of service requirements. In this paper, we address the relevant challenges of cross-layer design requirements for real-time rate adaptation of ultrasound video streaming in mobile WiMAX and HSUPA networks. A comparative performance analysis of such approach is validated in two experimental m-health test bed systems for both mobile WiMAX and HSUPA networks. The experimental results have shown an improved performance of mobile WiMAX compared to the HSUPA using the same cross-layer optimization approach.

Bridge over troubled water: Guidance crosses | Amundson ...

African Journals Online (AJOL)

This article is based on a keynote presentation at an international conference where the focus was cross-over career guidance. Simon and Garfunkel's popular song, "Bridge ... and the future, and building connections. There also was the suggestion that other metaphors could be used as a way to broaden the exploration.

Once-Yearly Zoledronic Acid and Days of Disability, Bed Rest, and Back Pain: Randomized, Controlled HORIZON Pivotal Fracture Trial

Science.gov (United States)

Cauley, Jane A.; Black, Dennis; Boonen, Steven; Cummings, Steven R.; Mesenbrink, Peter; Palermo, Lisa; Man, Zulema; Hadji, Peyman; Reid, Ian R.

2016-01-01

The objective of this study was to determine the effect of once-yearly zoledronic acid on the number of days of back pain and the number of days of disability (ie, limited activity and bed rest) owing to back pain or fracture in postmenopausal women with osteoporosis. This was a multicenter, randomized, double-blind, placebo-controlled trial in 240 clinical centers in 27 countries. Participants included 7736 postmenopausal women with osteoporosis. Patients were randomized to receive either a single 15-minute intravenous infusion of zoledronic acid (5 mg) or placebo at baseline, 12 months, and 24 months. The main outcome measures were self-reported number of days with back pain and the number of days of limited activity and bed rest owing to back pain or a fracture, and this was assessed every 3 months over a 3-year period. Our results show that although the incidence of back pain was high in both randomized groups, women randomized to zoledronic acid experienced, on average, 18 fewer days of back pain compared with placebo over the course of the trial (p = .0092). The back pain among women randomized to zoledronic acid versus placebo resulted in 11 fewer days of limited activity (p = .0017). In Cox proportional-hazards models, women randomized to zoledronic acid were about 6% less likely to experience 7 or more days of back pain [relative risk (RR) = 0.94, 95% confidence interval (CI) 0.90–0.99] or limited activity owing to back pain (RR = 0.94, 95% CI 0.87–1.00). Women randomized to zoledronic acid were significantly less likely to experience 7 or more bed-rest days owing to a fracture (RR = 0.58, 95% CI 0.47–0.72) and 7 or more limited-activity days owing to a fracture (RR = 0.67, 95% CI 0.58–0.78). Reductions in back pain with zoledronic acid were independent of incident fracture. Our conclusion is that in women with postmenopausal osteoporosis, a once-yearly infusion with zoledronic acid over a 3-year period significantly reduced the number of days that

A Cross-Layer Approach in Sensing and Resource Allocation for Multimedia Transmission over Cognitive UWB Networks

NARCIS (Netherlands)

Aripin, N.M.; Rashid, R.A.; Fisal, N.; Lo, A.C.C.; Ariffin, S.H.S.; Yusof, S.K.S.

2010-01-01

We propose an MAC centric cross-layer approach to address the problem of multimedia transmission over cognitive Ultra Wideband (C-UWB) networks. Several fundamental design issues, which are related to application (APP), medium access control (MAC), and physical (PHY) layer, are discussed. Although

1-800-CALL-H.E.P. -- Experiences on a voice-over-IP test bed

International Nuclear Information System (INIS)

Matthews, W.

2000-01-01

Highly interactive Internet applications such as Voice-over-IP are extremely sensitive to network performance. Even on high performance research networks, many cases will require the use of differentiated services to achieve high (toll) quality conversations. In this talk the authors will describe a test bed over the Energy Sciences network (ESnet) between Lawrence Berkeley National Laboratory (LBNL), Stanford Linear Accelerator Center (SLAC), Argonne National Laboratory (ANL) and Sandia National Laboratory (Sandia). In particular the characteristics of Voice-over-IP calls between LBNL and SLAC will be reviewed and the effect of low, moderate and high congestion on the link will be quantified. The use of Per Hop Behavior (PHB) in IP headers with Weighted Fair Queuing (WFQ) in routers and the benefit they provide will be explained. A model of flows and performance will be presented and new techniques to predict the quality of calls are under development and will be reviewed. Comparisons with telephone reliability will be discussed and the feasibility of wide spread deployment of VoIP in HEP will be considered

Fluidized bed reactor for processing particles coated with carbon

International Nuclear Information System (INIS)

Marschollek, M.; Simon, W.; Walter, C.

1978-01-01

The carbon coating of production returns of these particles first has to be removed before the heavy metal core released can be reprocessed. For reasons of criticality, removal of burnt-up particles downwards must be possible in the fluidized bed reactor even if the reactor diameter is greater than 800 mm, and the material temperatures must not exceed 650 0 C. It consists of an upper cylindrical and a lower conical part, where, according to the invention, the gas distributor heads in the conical part are situated in several planes above one another for the fluidisation and combustion gas and where they are evently distributed over the reactor crossection, so that an even flow profile is achieved over the reactor cross section. (HP) [de

Effects of pressure drop and superficial velocity on the bubbling fluidized bed incinerator.

Science.gov (United States)

Wang, Feng-Jehng; Chen, Suming; Lei, Perng-Kwei; Wu, Chung-Hsing

2007-12-01

Since performance and operational conditions, such as superficial velocity, pressure drop, particles viodage, and terminal velocity, are difficult to measure on an incinerator, this study used computational fluid dynamics (CFD) to determine numerical solutions. The effects of pressure drop and superficial velocity on a bubbling fluidized bed incinerator (BFBI) were evaluated. Analytical results indicated that simulation models were able to effectively predict the relationship between superficial velocity and pressure drop over bed height in the BFBI. Second, the models in BFBI were simplified to simulate scale-up beds without excessive computation time. Moreover, simulation and experimental results showed that minimum fluidization velocity of the BFBI must be controlled in at 0.188-3.684 m/s and pressure drop was mainly caused by bed particles.

Space station environmental control and life support systems test bed program - an overview

Science.gov (United States)

Behrend, Albert F.

As the National Aeronautics and Space Administration (NASA) begins to intensify activities for development of the Space Station, decisions must be made concerning the technical state of the art that will be baselined for the initial Space Station system. These decisions are important because significant potential exists for enhancing system performance and for reducing life-cycle costs. However, intelligent decisions cannot be made without an adequate assessment of new and ready technologies, i.e., technologies which are sufficiently mature to allow predevelopment demonstrations to prove their application feasibility and to quantify the risk associated with their development. Therefore, the NASA has implemented a technology development program which includes the establishment of generic test bed capabilities in which these new technologies and approaches can be tested at the prototype level. One major Space Station subsystem discipline in which this program has been implemented is the environmental control and life support system (ECLSS). Previous manned space programs such as Gemini, Apollo, and Space Shuttle have relied heavily on consumables to provide environmental control and life support services. However, with the advent of a long-duration Space Station, consumables must be reduced within technological limits to minimize Space Station resupply penalties and operational costs. The use of advanced environmental control and life support approaches involving regenerative processes offers the best solution for significant consumables reduction while also providing system evolutionary growth capability. Consequently, the demonstration of these "new technologies" as viable options for inclusion in the baseline that will be available to support a Space Station initial operational capability in the early 1990's becomes of paramount importance. The mechanism by which the maturity of these new regenerative life support technologies will be demonstrated is the Space

Thermal/chemical degradation of ceramic cross-flow filter materials

Energy Technology Data Exchange (ETDEWEB)

Alvin, M.A.; Lane, J.E.; Lippert, T.E.

1989-11-01

This report summarizes the 14-month, Phase 1 effort conducted by Westinghouse on the Thermal/Chemical Degradation of Ceramic Cross-Flow Filter Materials program. In Phase 1 expected filter process conditions were identified for a fixed-bed, fluid-bed, and entrained-bed gasification, direct coal fired turbine, and pressurized fluidized-bed combustion system. Ceramic cross-flow filter materials were also selected, procured, and subjected to chemical and physical characterization. The stability of each of the ceramic cross-flow materials was assessed in terms of potential reactions or phase change as a result of process temperature, and effluent gas compositions containing alkali and fines. In addition chemical and physical characterization was conducted on cross-flow filters that were exposed to the METC fluid-bed gasifier and the New York University pressurized fluidized-bed combustor. Long-term high temperature degradation mechanisms were proposed for each ceramic cross-flow material at process operating conditions. An experimental bench-scale test program is recommended to be conducted in Phase 2, generating data that support the proposed cross-flow filter material thermal/chemical degradation mechanisms. Papers on the individual subtasks have been processed separately for inclusion on the data base.

Gravity-driven, dry granular flows over a loose bed in stationary and homogeneous conditions

Science.gov (United States)

Meninno, Sabrina; Armanini, Aronne; Larcher, Michele

2018-02-01

Flows involving solid particulates have been widely studied in recent years, but their dynamics are still a complex issue to model because they strongly depend on the interaction with the boundary conditions. We report on laboratory investigations regarding homogeneous and steady flows of identical particles over a loose bed in a rectangular channel. Accurate measurements were carried out through imaging techniques to estimate profiles of the mean velocity, solid concentration, and granular temperature for a large set of flow rates and widths. Vertical and transversal structures observed in the flow change as interparticle interactions become more collisional, and they depend on the bottom over which the flow develops. The lateral confinement has a remarkable effect on the flow, especially for narrow channels compared with the grain size, and a hydraulic analogy is able to show how the walls influence the mechanisms of friction and energy dissipation.

Deep Bed Iodine Sorbent Testing FY 2011 Report

International Nuclear Information System (INIS)

Soelberg, Nick; Watson, Tony

2011-01-01

Nuclear fission results in the production of fission products (FPs) and activation products that increasingly interfere with the fission process as their concentrations increase. Some of these fission and activation products tend to evolve in gaseous species during used nuclear fuel reprocessing. Analyses have shown that I129, due to its radioactivity, high potential mobility in the environment, and high longevity (half life of 15.7 million years), can require control efficiencies of up to 1,000x or higher to meet regulatory emission limits. Deep-bed iodine sorption testing has been done to evaluate the performance of solid sorbents for capturing iodine in off-gas streams from nuclear fuel reprocessing plants. The objectives of the FY 2011 deep bed iodine sorbent testing are: (1) Evaluate sorbents for iodine capture under various conditions of gas compositions and operating temperature (determine sorption efficiencies, capacities, and mass transfer zone depths); and (2) Generate data for dynamic iodine sorption modeling. Three tests performed this fiscal year on silver zeolite light phase (AgZ-LP) sorbent are reported here. Additional tests are still in progress and can be reported in a revision of this report or a future report. Testing was somewhat delayed and limited this year due to initial activities to address some questions of prior testing, and due to a period of maintenance for the on-line GC. Each test consisted of (a) flowing a synthetic blend of gases designed to be similar to an aqueous dissolver off-gas stream over the sorbent contained in three separate bed segments in series, (b) measuring each bed inlet and outlet gas concentrations of iodine and methyl iodide (the two surrogates of iodine gas species considered most representative of iodine species expected in dissolver off-gas), (c) operating for a long enough time to achieve breakthrough of the iodine species from at least one (preferably the first two) bed segments, and (d) post-test purging

Sildenafil citrate (Viagra) and erectile dysfunction following external beam radiotherapy for prostate cancer: a randomized, double-blind, placebo-controlled, cross-over study

International Nuclear Information System (INIS)

Incrocci, Luca; Koper, Peter C.M.; Hop, Wim C.J.; Slob, A. Koos

2001-01-01

Purpose: To determine the efficacy of sildenafil citrate (Viagra) in patients with erectile dysfunction after three-dimensional conformal external beam radiotherapy (3D-CRT) for prostate cancer. Methods and Materials: 406 patients with complaints of erectile dysfunction and who completed radiation at least 6 months before the study were approached by mail. 3D-CRT had been delivered (mean dose 68 Gy). Sixty patients were included and entered a double-blind, placebo-controlled, cross-over study lasting 12 weeks. They received during 2 weeks 50 mg of sildenafil or placebo; at Week 2 the dose was increased to 100 mg in case of unsatisfactory erectile response. At Week 6, patients crossed over to the alternative treatment. Data were collected using the International Index of Erectile Function (IIEF) questionnaire, and side effects were recorded. Results: Mean age was 68 years. All patients completed the study. For most questions of the IIEF questionnaire there was a significant increase in mean scores from baseline with sildenafil, but not with placebo. Ninety percent of the patients needed a dose adjustment to 100 mg sildenafil. Side effects were mild or moderate. Conclusion: Sildenafil is well tolerated and effective in improving erectile function of patients with ED after 3D-CRT for prostate cancer

The correction of pebble bed reactor nodal cross sections for the effects of leakage and depletion history

Science.gov (United States)

Hudson, Nathanael Harrison

An accurate and computationally fast method to generate nodal cross sections for the Pebble Bed Reactor (PBR) was presented. In this method, named Spectral History Correction (SHC), a set of fine group microscopic cross section libraries, pre-computed at specified depletion and moderation states, was coupled with the nodal nuclide densities and group bucklings to compute the new fine group spectrum for each node. The relevant fine group cross-section library was then recollapsed to the local broad group cross-section structure with this new fine group spectrum. This library set was tracked in terms of fuel isotopic densities. Fine group modulation factors (to correct the homogeneous flux for heterogeneous effects) and fission spectra were also stored with the cross section library. As the PBR simulation converges to a steady state fuel cycle, the initial nodal cross section library becomes inaccurate due to the burnup of the fuel and the neutron leakage into and out of the node. Because of the recirculation of discharged fuel pebbles with fresh fuel pebbles, a node can consist of a collection of pebbles at various burnup stages. To account for the nodal burnup, the microscopic cross sections were combined with nodal averaged atom densities to approximate the fine group macroscopic cross-sections for that node. These constructed, homogeneous macroscopic cross sections within the node were used to calculate a numerical solution for the fine group spectrum with B1 theory. This new fine spectrum was used to collapse the pre-computed microscopic cross section library to the broad group structure employed by the fuel cycle code. This SHC technique was developed and practically implemented as a subroutine within the PBR fuel cycle code PEBBED. The SHC subroutine was called to recalculate the broad group cross sections during the code convergence. The result was a fast method that compared favorably to the benchmark scheme of cross section calculation with the lattice

Loading and Unloading Weaned Pigs: Effects of Bedding Types, Ramp Angle, and Bedding Moisture

Directory of Open Access Journals (Sweden)

Arlene Garcia

2014-12-01

Full Text Available The use of non-slip surfaces during loading and unloading of weaned pigs plays an important role in animal welfare and economics of the pork industry. Currently, the guidelines available only suggest the use of ramps below 20° to load and unload pigs. Three ramp angles (0°, 10° or 20°, five bedding materials (nothing, sand, feed, wood shavings or wheat straw hay, two moistures (dry or wet bedding; >50% moisture over two seasons (>23.9 °C summer, <23.9 °C winter were assessed for slips/falls/vocalizations (n = 6,000 pig observations. “Score” was calculated by the sum of slips, falls, and vocalizations. With the exception of using feed as a bedding, all beddings provided some protection against elevated slips, falls, and vocalizations (P < 0.01. Providing bedding reduced (P < 0.05 scores regardless of whether the bedding was dry or wet. Scores increased as the slope increased (P < 0.01. Provision of bedding, other than feed, at slopes greater than zero, decreased slips, falls and vocalizations. The total time it took to load and unload pigs was

Field Study of the Comparative Efficacy of Three Pyrethroid/Neonicotinoid Mixture Products for the Control of the Common Bed Bug, Cimex lectularius

Directory of Open Access Journals (Sweden)

Changlu Wang

2015-03-01

Full Text Available Three insecticide mixtures that contain two classes of insecticides (pyrethroid and neonicotinoid were recently developed to control bed bugs. We evaluated three integrated bed bug management strategies in apartments, each using the same non-chemical control methods and one of the three insecticide mixture products: Tandem (lambda-cyhalothrin + thiamethoxam, Temprid SC (beta-cyfluthrin + imidacloprid, and Transport Mikron (bifenthrin + acetamiprid. No insecticides were applied in the Control apartments. In all apartments, we installed vinyl mattress encasements (if not already present and applied steam to beds and other infested upholstered furniture. Insecticide sprays were applied in the three treatments. Each treatment and the Control included 8–10 occupied apartments. Re-treatment was conducted during biweekly inspections if necessary. After eight weeks, the mean (± SEM bed bug count reduction in the Tandem, Temprid SC, Transport Mikron, and Control was 89 ± 9, 87 ± 6, 98 ± 1, and 23 ± 54%, respectively. Only Tandem and Transport Mikron treatments resulted in significantly higher population reduction than the Control at eight weeks. There were no significant differences in mean percent reduction among the three treatments (Tandem, Temprid SC, Transport Mikron at eight weeks. Tandem spray caused significantly faster bed bug reduction than Temprid SC spray and Transport Mikron spray.

Strong Shock Propagating Over A Random Bed of Spherical Particles

Science.gov (United States)

Mehta, Yash; Salari, Kambiz; Jackson, Thomas L.; Balachandar, S.; Thakur, Siddharth

2017-11-01

The study of shock interaction with particles has been largely motivated because of its wide-ranging applications. The complex interaction between the compressible flow features, such as shock wave and expansion fan, and the dispersed phase makes this multi-phase flow very difficult to predict and control. In this talk we will be presenting results on fully resolved inviscid simulations of shock interaction with random bed of particles. One of the fascinating observations from these simulations are the flow field fluctuations due to the presence of randomly distributed particles. Rigorous averaging (Favre averaging) of the governing equations results in Reynolds stress like term, which can be classified as pseudo turbulence in this case. We have computed this ``Reynolds stress'' term along with individual fluctuations and the turbulent kinetic energy. Average pressure was also computed to characterize the strength of the transmitted and the reflected waves. This work was supported by the U.S. Department of Energy, National Nuclear Security Administration, Advanced Simulation and Computing Program, as a Cooperative Agreement under the Predictive Science Academic Alliance Program.

ESTABLISHMENT OF AN ENVIRONMENTAL CONTROL TECHNOLOGY LABORATORY WITH A CIRCULATING FLUIDIZED-BED COMBUSTION SYSTEM

Energy Technology Data Exchange (ETDEWEB)

Wei-Ping Pan; Andy Wu; John T. Riley

2004-10-30

This report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period July 1, 2004 through September 30, 2004. The following tasks have been completed. First, renovation of the new Combustion Laboratory and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building have started. Second, the design if the component parts of the CFBC system have been reviewed and finalized so that the drawings may be released to the manufacturers during the next quarter. Third, the experiments for solid waste (chicken litter) incineration have been conducted using a Thermogravimetric Analyzer (TGA). This is in preparation for testing in the simulated fluidized-bed combustor. The experimental results from this study are presented in this report. Finally, the proposed work for the next quarter has been outlined in this report.

Arthroscopy or ultrasound in undergraduate anatomy education: a randomized cross-over controlled trial

Directory of Open Access Journals (Sweden)

Knobe Matthias

2012-09-01

Full Text Available Abstract Background The exponential growth of image-based diagnostic and minimally invasive interventions requires a detailed three-dimensional anatomical knowledge and increases the demand towards the undergraduate anatomical curriculum. This randomized controlled trial investigates whether musculoskeletal ultrasound (MSUS or arthroscopic methods can increase the anatomical knowledge uptake. Methods Second-year medical students were randomly allocated to three groups. In addition to the compulsory dissection course, the ultrasound group (MSUS was taught by eight, didactically and professionally trained, experienced student-teachers and the arthroscopy group (ASK was taught by eight experienced physicians. The control group (CON acquired the anatomical knowledge only via the dissection course. Exposure (MSUS and ASK took place in two separate lessons (75 minutes each, shoulder and knee joint and introduced standard scan planes using a 10-MHz ultrasound system as well as arthroscopy tutorials at a simulator combined with video tutorials. The theoretical anatomic learning outcomes were tested using a multiple-choice questionnaire (MCQ, and after cross-over an objective structured clinical examination (OSCE. Differences in student’s perceptions were evaluated using Likert scale-based items. Results The ASK-group (n = 70, age 23.4 (20–36 yrs. performed moderately better in the anatomical MC exam in comparison to the MSUS-group (n = 84, age 24.2 (20–53 yrs. and the CON-group (n = 88, 22.8 (20–33 yrs.; p = 0.019. After an additional arthroscopy teaching 1% of students failed the MC exam, in contrast to 10% in the MSUS- or CON-group, respectively. The benefit of the ASK module was limited to the shoulder area (p Conclusions The additional implementation of arthroscopy tutorials to the dissection course during the undergraduate anatomy training is profitable and attractive to students with respect to complex joint anatomy. Simultaneous

Binge Eating Disorder (BED in Relation to Addictive Behaviors and Personality Risk Factors

Directory of Open Access Journals (Sweden)

Caroline Davis

2017-04-01

Full Text Available While there is good evidence that binge eating disorder (BED is linked to higher-than-expected use of a broad range of addictive behaviors, mechanisms underlying this association are not well understood. Using a mediation-analytical approach with three age- and gender-matched groups – overweight/obese adults with (n = 42 and without (n = 104 BED, and normal-weight control participants (n = 73 – we tested the hypothesis that adults with BED would engage in more addictive behaviors and have higher scores on a personality-risk index than the two control groups. We also anticipated that the relationship between BED and addictive behaviors would be mediated by a high-risk personality profile. The predicted mediation effect was strongly supported. Contrary to expectation, BED participants did not engage in more addictive behaviors or have higher personality-risk scores than their weight-matched counterparts. However, both overweight/obese groups did have significantly higher scores than the normal-weight group. The relationships among personality risk, elevated body mass index (BMI, and addictive behaviors have important clinical implications, especially for treatments that target psycho-behavioral intervention for compulsive overeating and substance-use disorders.

Binge Eating Disorder (BED) in Relation to Addictive Behaviors and Personality Risk Factors.

Science.gov (United States)

Davis, Caroline; Mackew, Laura; Levitan, Robert D; Kaplan, Allan S; Carter, Jacqueline C; Kennedy, James L

2017-01-01

While there is good evidence that binge eating disorder (BED) is linked to higher-than-expected use of a broad range of addictive behaviors, mechanisms underlying this association are not well understood. Using a mediation-analytical approach with three age- and gender-matched groups - overweight/obese adults with ( n = 42) and without ( n = 104) BED, and normal-weight control participants ( n = 73) - we tested the hypothesis that adults with BED would engage in more addictive behaviors and have higher scores on a personality-risk index than the two control groups. We also anticipated that the relationship between BED and addictive behaviors would be mediated by a high-risk personality profile. The predicted mediation effect was strongly supported. Contrary to expectation, BED participants did not engage in more addictive behaviors or have higher personality-risk scores than their weight-matched counterparts. However, both overweight/obese groups did have significantly higher scores than the normal-weight group. The relationships among personality risk, elevated body mass index (BMI), and addictive behaviors have important clinical implications, especially for treatments that target psycho-behavioral intervention for compulsive overeating and substance-use disorders.

The relationship between bed size and profitability in South Carolina hospitals.

Science.gov (United States)

Kim, Yang K; Glover, Saundra H; Stoskopf, Carleen H; Boyd, Suzan D

2002-01-01

The purpose of the study is to identify factors affecting hospital profitability and to find the optimal hospital bed size that assures maximum profit. This is a cross-sectional study using survey data obtained from acute care hospitals in South Carolina in 1997. The relationship of hospital profitability and hospital bed size revealed that when bed size increases, hospital profitability increases, decreases, and then increases again. For the patient profit proportion, the turning points in bed size are 238.22 and 560.08. For the total profit proportion, the turning points in bed size are 223.31 and 503.86. The results on the relationship between bed size and hospital profitability indicate that medium-size hospitals have less profitability.

Cross-Layer Adaptive Feedback Scheduling of Wireless Control Systems

Directory of Open Access Journals (Sweden)

Jinxiang Dong

2008-07-01

Full Text Available There is a trend towards using wireless technologies in networked control systems. However, the adverse properties of the radio channels make it difficult to design and implement control systems in wireless environments. To attack the uncertainty in available communication resources in wireless control systems closed over WLAN, a cross-layer adaptive feedback scheduling (CLAFS scheme is developed, which takes advantage of the co-design of control and wireless communications. By exploiting crosslayer design, CLAFS adjusts the sampling periods of control systems at the application layer based on information about deadline miss ratio and transmission rate from the physical layer. Within the framework of feedback scheduling, the control performance is maximized through controlling the deadline miss ratio. Key design parameters of the feedback scheduler are adapted to dynamic changes in the channel condition. An eventdriven invocation mechanism for the feedback scheduler is also developed. Simulation results show that the proposed approach is efficient in dealing with channel capacity variations and noise interference, thus providing an enabling technology for control over WLAN.

Continuous synthesis of methanol: heterogeneous hydrogenation of ethylene carbonate over Cu/HMS catalysts in a fixed bed reactor system.

Science.gov (United States)

Chen, Xi; Cui, Yuanyuan; Wen, Chao; Wang, Bin; Dai, Wei-Lin

2015-09-18

Continuous fixed-bed catalytic hydrogenation of ethylene carbonate (EC) to methanol and ethylene glycol (EG), an emerging synthetic process of methanol via indirect conversion of CO2, was successfully performed over Cu/HMS catalysts prepared by the ammonia evaporation (AE) method. The catalysts possessed superb performance with a conversion of 100% and a selectivity to methanol of 74%.

Preferences of group-housed female mice regarding structure of softwood bedding.

Science.gov (United States)

Kirchner, J; Hackbarth, H; Stelzer, H D; Tsai, P-P

2012-04-01

Bedding influences various parameters in the housing of laboratory mice, such as health, physiology and behaviour (often considered as being integral parts of welfare). Notwithstanding existent studies about bedding preferences of individually tested mice, data about group-housed mice are still lacking. The aim of this study was to find out the structure preference for softwood bedding of group-housed mice. One hundred and eight 8-week-old female mice (C57BL6/JOlaHsd and BALB/cOlaHsd) were housed in groups of three and were given one-week free access to two different bedding structures at a time. In three test combinations, softwood shaving bedding was tested versus softwood chip bedding products of three different particle sizes (fine/medium/coarse-grained). The preference test was performed in a DoubleCage system composed of two Makrolon type IIL cages, connected by a perspex tunnel. This validated system was able to detect the crossings of each individual animal with correct crossing time and direction. On the basis of these data, dwelling times on the particular bedding structures were statistically analysed as a parameter for bedding preferences. In all three test combinations, a highly significant shaving preference was detected. On average, mice spent 70% of their dwelling time on the shavings. This preference was more explicit during the light period and in C57BL/6J mice. The relative ranking of the bedding structures was: shavings > coarse-grained chips > medium chips = fine chips. By means of these results, a shaving structure as bedding can be recommended for laboratory mice, whereas fine chip structures should be avoided.

Find a Bed Bug Pesticide Product

Science.gov (United States)

Introduces the Bed Bug Product Search Tool, to help consumers find EPA-registered pesticides for bed bug infestation control. Inclusion in this database is not an endorsement. Always follow label directions carefully.

Evaluating the Acoustic Benefits of Over-the-Rotor Acoustic Treatments Installed on the Advanced Noise Control Fan

Science.gov (United States)

Gazella, Matthew R.; Takakura, Tamuto; Sutliff, Daniel L.; Bozak, Richard F.; Tester, Brian J.

2017-01-01

Over the last 15 years, over-the-rotor acoustic treatments have been evaluated by NASA with varying success. Recently, NASA has been developing the next generation of over-the-rotor acoustic treatments for fan noise reduction. The NASA Glenn Research Centers Advanced Noise Control Fan was used as a Low Technology Readiness Level test bed. A rapid prototyped in-duct array consisting of 50 microphones was employed, and used to correlate the in-duct analysis to the far-field acoustic levels and to validate an existing beam-former method. The goal of this testing was to improve the Technology Readiness Level of various over-the-rotor acoustic treatments by advancing the understanding of the physical mechanisms and projecting the far-field acoustic benefit.

Experiments on Pool-riffle Sequences with Multi-fractional Sediment Bed During Floods

Science.gov (United States)

Rodriguez, J. F.; Vahidi, E.; Bayat, E.; de Almeida, G. A. M.; Saco, P. M.

2017-12-01

The morphodynamics of pools and riffles has been the subject of research for over a century and has more recently attracted intense attention for their central role in providing habitat diversity conditions, both in terms of flow and substrate. Initial efforts to explain the long-term stability of the pool-riffle (PR) sequences (often referred to as self-maintenance) focused almost exclusively on cross sectional flow characteristics (either average or near bed velocity or shear stress), using episodic shifts in higher shear stress or velocities from riffles to pools during floods (i.e. reversal conditions) as an indication of the long-term self-maintenance of the structures.. However, less attention has been paid to the interactions of flow unsteadiness, sediment supply and sedimentological contrasts as the drivers for maintaining PR sequences. Here we investigate these effects through laboratory experiments on a scaled-down PR sequence of an existing gravel bed river. Froude similitude and equality of Shields' number were applied to scale one- to four-year recurrence flood events and sediment size distributions, respectively. We conducted experiments with different hydrographs and different sedimentological conditions. In each experiment we continuously measured velocities and shear stresses (using acoustic velocity profilers) bed levels (using a bed profiler) and bed grain size distribution (using an automatic digital technique on the painted bed sediments) during the hydrographs. Our results show that the most important factors for self-maintenance were the sediment bed composition, the level of infilling of the pool and the sediment supply grainsize distribution. These results highlight the need to consider the time varying sedimentological characteristics of a PR sequence to assess its capacity for self-maintenance.

Comparing ownership and use of bed nets at two sites with differential malaria transmission in western Kenya.

Science.gov (United States)

Ernst, Kacey C; Hayden, Mary H; Olsen, Heather; Cavanaugh, Jamie L; Ruberto, Irene; Agawo, Maurice; Munga, Stephen

2016-04-14

Challenges persist in ensuring access to and optimal use of long-lasting, insecticidal bed nets (LLINs). Factors associated with ownership and use may differ depending on the history of malaria and prevention control efforts in a specific region. Understanding how the cultural and social-environmental context of bed net use may differ between high- and low-risk regions is important when identifying solutions to improve uptake and appropriate use. Community forums and a household, cross-sectional survey were used to collect information on factors related to bed net ownership and use in western Kenya. Sites with disparate levels of transmission were selected, including an endemic lowland area, Miwani, and a highland epidemic-prone area, Kapkangani. Analysis of ownership was stratified by site. A combined site analysis was conducted to examine factors associated with use of all available bed nets. Logistic regression modelling was used to determine factors associated with ownership and use of owned bed nets. Access to bed nets as the leading barrier to their use was identified in community forums and cross-sectional surveys. While disuse of available bed nets was discussed in the forums, it was a relatively rare occurrence in both sites. Factors associated with ownership varied by site. Education, perceived risk of malaria and knowledge of individuals who had died of malaria were associated with higher bed net ownership in the highlands, while in the lowlands individuals reporting it was easy to get a bed net were more likely to own one. A combined site analysis indicated that not using an available bed net was associated with the attitudes that taking malaria drugs is easier than using a bed net and that use of a bed net will not prevent malaria. In addition, individuals with an unused bed net in the household were more likely to indicate that bed nets are difficult to use, that purchased bed nets are better than freely distributed ones, and that bed nets should only

A depositional model for the Taylor coal bed, Martin and Johnson counties, eastern Kentucky

Science.gov (United States)

Andrews, W.M.; Hower, J.C.; Ferm, J.C.; Evans, S.D.; Sirek, N.S.; Warrell, M.; Eble, C.F.

1996-01-01

This study investigated the Taylor coal bed in Johnson and Martin counties, eastern Kentucky, using field and petrographic techniques to develop a depositional model of the coal bed. Petrography and chemistry of the coal bed were examined. Multiple benches of the Taylor coal bed were correlated over a 10 km distance. Three sites were studied in detail. The coal at the western and eastern sites were relatively thin and split by thick clastic partings. The coal at the central site was the thickest and unsplit. Two major clastic partings are included in the coal bed. Each represents a separate and distinct fluvial splay. The Taylor is interpreted to have developed on a coastal plain with periodic flooding from nearby, structurally-controlled fluvial systems. Doming is unlikely due to the petrographic and chemical trends, which are inconsistent with modern Indonesian models. The depositional history and structural and stratigraphic setting suggest contemporaneous structural influence on thickness and quality of the Taylor coal bed in this area.

Fluid-bed process for SYNROC production

International Nuclear Information System (INIS)

Ackerman, F.J.; Grens, J.Z.; Ryerson, F.J.; Hoenig, C.L.; Bazan, F.; Peters, P.E.; Smith, R.; Campbell, J.H.

1983-01-01

SYNROC is a titanate-based ceramic waste developed for the immobilization of high-level nuclear reactor waste. Lawrence Livermore National Laboratory (LLNL) has investigated a fluid-bed technique for the large-scale production of SYNROC precursor powders. Making SYNROC in a fluid bed permits slurry drying, calcination and reduction-oxidation reactions to be carried out in a single unit. We present the results of SYNROC fluid-bed studies from two fluid-bed units 10 cm in diameter: an internally heated fluid-bed unit developed by Exxon Idaho and an externally heated unit constructed at LLNL. Bed operation over a range of temperatures, feed rates, fluidizing rates, and redox conditions indicate that SYNROC powders of a high density and a uniform particle size can be produced. These powders facilitate the densification step and yield dense ceramics (greater than 95% theoretical density) with well-developed phases and low leaching rates

Determination of the coke bed voidage in the blast furnace hearth

Energy Technology Data Exchange (ETDEWEB)

Havelange, O.; Danloy, G.; Venturini, M.J. [and others] [CRM, Liege (Belgium)

2004-07-01

The objectives of the research were to develop and apply techniques and model tools allowing an online evaluation of the blast furnace hearth conditions and its permeability, in order to guarantee a stable furnace operation and to control the refractory wear through early corrective actions. CRM determined the coke bed voidage in the hearth of BFB of Cockerill-Sambre by two techniques: one based on pressure measurement inside the taphole and the other based on electromotive force measurement. A mathematicalmodel was developed taking into account the movements of the deadman. ln order to continuously determine the hot metal flow rate, BFI measured the filling level in the runner at BF 2 of TKS. A statistical wear model evaluated the cross-sectional runner geometry. The data have been fed into a model to calculate the coke bed voidage on multiple taphole blast furnaces. To control the wear caused by preferential liquid flow, Corus IJmuiden developed a monitoring of temperature and heat flux information from purpose-installed duplex thermocouples. This information has been correlated over time to identify any persistent trends and used to evaluate control measures such as blocked tuyeres and process shutdowns. Industrial trials at Fos BF1 enabled IRSID to propose a picture to describe the effects of the central coke charging practice. IRSID used the Fluent code to describe the liquid flow in the hearth with regard to the deadman conditions and to simulate tracer experiments. From studies of the behaviour of the hearth skull, Corus UK proposed a method for its monitoring. The iron flow rate was measured by using strain gauges attached to the torpedo ladles, and the slag flow rate was estimated from the slag pelletiser current. Data from tuyere core drilling samples were examined to estimate the voidage in the hearth. 38 refs., 127 figs.

Double-blind, placebo-controlled cross-over study of intravenous S-adenosyl-L-methionine in patients with fibromyalgia

DEFF Research Database (Denmark)

Volkmann, H; Nørregaard, J; Jacobsen, Søren

1997-01-01

The objective of this study was to test the efficacy of intravenously administered S-adenosyl-L-methionine (SAMe) in patients with fibromyalgia (FM). Thirty-four out-patients with fibromyalgia symptoms received SAMe 600 mg i.v. or placebo daily for 10 days in a cross-over trial. There was no sign......The objective of this study was to test the efficacy of intravenously administered S-adenosyl-L-methionine (SAMe) in patients with fibromyalgia (FM). Thirty-four out-patients with fibromyalgia symptoms received SAMe 600 mg i.v. or placebo daily for 10 days in a cross-over trial....... There was no significant difference in improvement in the primary outcome: tender point change between the two treatment groups. There was a tendency towards statistical significance in favour of SAMe on subjective perception of pain at rest (p = 0.08), pain on movement (p = 0.11), and overall well-being (p = 0.......17) and slight improvement only on fatigue, quality of sleep, morning stiffness, and on the Fibromyalgia Impact Questionnaire for pain. No effect could be observed on isokinetic muscle strength, Zerrsen self-assessment questionnaire, and the face scale. No effect of SAMe in patients with FM was found...

Toxicity of selected essential oils, silicone oils, and paraffino oil against the common bed bug, cimex lectularius L. (Hemiptera: Cimicidae)

Science.gov (United States)

The common bed bug (Cimex lectularius L.) resurged in the U.S. and many other countries over the past decade. The need for safe and effective bed bug control products propelled the development of numerous “green pesticides”, mostly with essential oils listed as active ingredients. Various inorganic ...

Fluidized bed selective pyrolysis of coal

Science.gov (United States)

Shang, Jer Y.; Cha, Chang Y.; Merriam, Norman W.

1992-01-01

The present invention discloses a process for the pyrolysis of coal which comprises the effective utilization of two zonal inclined fluidized beds, where said zones can be selectively controlled as to temperature and heating rate. The first zonal inclined fluidized bed serves as a dryer for crushed coal and additionally is controlled to selectively pyrolyze said coal producing substantially carbon dioxide for recycle use. The second zonal inclined fluidized bed further pyrolyzes the coal to gaseous, liquid and char products under controlled temperature and heating rate zones designed to economically integrate the product mix. The gas and liquid products are recovered from the gaseous effluent stream while the char which remains can be further treated or utilized in a subsequent process step.

Experimental, kinetic and numerical modeling of hydrogen production by catalytic reforming of crude ethanol over a commercial catalyst in packed bed tubular reactor and packed bed membrane reactor

International Nuclear Information System (INIS)

Aboudheir, Ahmed; Akande, Abayomi; Idem, Raphael

2006-01-01

The demand for hydrogen energy has increased tremendously in recent years essentially because of the increase in the word energy consumption as well as recent developments in fuel cell technologies. The energy information administration has projected that world energy consumption will increase by 59% over the next two decades, from 1999 to 2020, in which the largest share is still dominated by fossil fuels (oil, natural gas and coal). Carbon dioxide (CO 2 ) emissions resulting from the combustion of these fossil fuels currently are estimated to account for three-fourth of human-caused CO 2 emissions worldwide. Greenhouse gas emission, including CO 2 , should be limited, as recommended at the Kyoto Conference, Japan, in December 1997. In this regard, hydrogen (H 2 ) has a significant future potential as an alternative fuel that can solve the problems of CO 2 emissions as well as the emissions of other air contaminants. One of the techniques to produce hydrogen is by reforming of hydrocarbons or biomass. Crude ethanol (a form of biomass, which essentially is fermentation broth) is easy to produce, is free of sulphur, has low toxicity, and is also safe to handle, transport and store. In addition, crude ethanol consists of oxygenated hydrocarbons, such as ethanol, lactic acid, glycerol, and maltose. These oxygenated hydrocarbons can be reformed completely to H 2 and CO 2 , the latter of which could be separated from H 2 by membrane technology. This provides for CO 2 capture for eventual storage or destruction. In the case of using crude ethanol, this will result in negative CO 2 , emissions. In this paper, we conducted experimental work on production of hydrogen by the catalytic reforming of crude ethanol over a commercial promoted Ni-based catalyst in a packed bed tubular reactor as well as a packed bed membrane reactor. As well, a rigorous numerical model was developed to simulate this process in both the catalytic packed bed tubular reactor and packed bed membrane

Dark chocolate and vascular function in patients with peripheral artery disease: a randomized, controlled cross-over trial.

Science.gov (United States)

Hammer, Alexandra; Koppensteiner, Renate; Steiner, Sabine; Niessner, Alexander; Goliasch, Georg; Gschwandtner, Michael; Hoke, Matthias

2015-01-01

Flavonoid-rich dark chocolate has positive effects on vascular function in healthy subjects and in patients at risk of atherosclerosis. The impact of dark chocolate on endothelial and microvascular function in patients with symptomatic peripheral artery disease (PAD) has not been investigated so far. In an investigator blinded, randomized, controlled, cross-over trial we assessed the effect of flavonoid-rich dark chocolate and cocoa-free control chocolate on flow-mediated dilatation (FMD) of the brachial artery and on microvascular function (assessed by Laser Doppler fluxmetry) in 21 patients with symptomatic (Fontaine stage II) PAD. Measurements were done in each patient on 2 single days, with an interval of 7 days, at baseline and at 2 hours after ingestion of 50 g dark chocolate or 50 g white chocolate, respectively. FMD remained unchanged after intake of dark chocolate (baseline and 2 hours after ingestion, %: 5.1 [IQR 4.4 to 7.3] and 5.5 [IQR 3.9 to 10.4]; p = 0.57, and after intake of white chocolate (baseline and 2 hours after ingestion, %: 6.4 [IQR 4.5 to 11.4] and 4.4 [IQR 2.6 to 8.7]; p = 0.14. Similarly, microcirculatory parameters were not significantly altered after intake of any chocolate compared with the respective baseline values. In conclusion, a single consumption of 50 g dark chocolate has no effect on endothelial and microvascular function in patients with symptomatic PAD.

Improvement of Combustion Characteristics in Fluidized Bed

International Nuclear Information System (INIS)

Mohamed, H.S.; El Sourougy, M.R.; Faik, M.

2009-01-01

The present investigation is directed towards the experimental study of the effect of a new design of the bed temperature on the overall thermal efficiency and heat transfer by conduction, convection and radiation in gaseous fuel-fluidized bed combustion system. The experiments are performed on a water-cooled fluidized bed model furnace with cylindrical cross-section of 0.25 m diameter and its height is 0.60 m. the fluidising medium used is sand particles with average diameter 1.5 mm. The bed temperature is varied between 700 degree C and 1100 degree C. Measurements f carbon dioxide, carbon monoxide and oxygen concentrations are carried out by using water-cooled sampling probe, and infrared and paramagnetic analyzers. The results obtained show that the bed temperature, the total heat transfer to the wall and the bed combustion efficiency increase with the decrease of the air-fuel ratio. It is also found that 91% of the total heat transfer is in the fluidising part of the bed and most of this heat is transferred by convection from hot sand particles to the wall. Two empirical formulae for the calculation of the wall heat transfer coefficient and the particle convective heat transfer coefficient are proposed. A verification of the proposed empirical formulae is made by comparing the calculated values with the experimental results.

Carbon bed mercury emissions control for mixed waste treatment.

Science.gov (United States)

Soelberg, Nick; Enneking, Joe

2010-11-01

Mercury has various uses in nuclear fuel reprocessing and other nuclear processes, and so it is often present in radioactive and mixed (radioactive and hazardous) wastes. Compliance with air emission regulations such as the Hazardous Waste Combustor (HWC) Maximum Achievable Control Technology (MACT) standards can require off-gas mercury removal efficiencies up to 99.999% for thermally treating some mixed waste streams. Test programs have demonstrated this level of off-gas mercury control using fixed beds of granular sulfur-impregnated activated carbon. Other results of these tests include (1) the depth of the mercury control mass transfer zone was less than 15-30 cm for the operating conditions of these tests; (2) MERSORB carbon can sorb mercury up to 19 wt % of the carbon mass; and (3) the spent carbon retained almost all (98.3-99.99%) of the mercury during Toxicity Characteristic Leachability Procedure (TCLP) tests, but when even a small fraction of the total mercury dissolves, the spent carbon can fail the TCLP test when the spent carbon contains high mercury concentrations.

Effect of ionization, bedding, and feeding on air quality in a horse stable.

Science.gov (United States)

Siegers, Esther Willemijn; Anthonisse, Milou; van Eerdenburg, Frank J C M; van den Broek, Jan; Wouters, Inge M; Westermann, Cornélie Martine

2018-05-01

Organic dust is associated with Equine asthma. Ionization should reduce airborne dust levels. To determine the effect of ionization of air, type of bedding, and feed on the levels of airborne dust, endotoxin, and fungal colonies in horse stables. 24 healthy University-owned horses occupied the stables. A randomized controlled cross-over study. Four units with 6 stables were equipped with an ionization installation (25 VA, 5000 Volt Direct Current). Horses were kept either on wood shavings and fed haylage (2 units), or on straw and fed dry hay (2 units). Measurements were performed with and without activated ionization, during daytime and nighttime, repeatedly over the course of a week and repeatedly during 4-6 weeks. Statistical analysis was performed using a mixed effect model with Akaike's Information Criterion for model reduction and 95% profile (log) likelihood confidence intervals (CI). Ionization did not alter concentrations of dust, endotoxin, or fungi, fewer. In the units with straw and hay, the concentration of dust, endotoxin, and fungi (difference in logarithmic mean 1.92 (95%CI 1.71-2.12); 2.86 (95%CI 2.59-3.14); 1.75 (95%CI 1.13-2.36)) were significantly higher compared to wood shavings and haylage. The installation of a negative air-ionizer in the horse stable did not reduce concentrations of dust, endotoxin, and viable fungal spores. The substantial effect of low dust bedding and feed is confirmed. Copyright © 2018 The Authors. Journal of Veterinary Internal Medicine published by Wiley Periodicals, Inc. on behalf of the American College of Veterinary Internal Medicine.

Improving operability of spouted beds using a simple optimizing control structure

Directory of Open Access Journals (Sweden)

N. A. CORRÊA

1999-12-01

Full Text Available In operations using spouted beds, it is of major importance, from an energy consumption point of view, to operate the process as close as possible to the minimum spout flow. At this point, the speed of the gas (for example, warm air in drying operations is greater than the amount of heat and mass transfer involved, although it only transfers the minimum amount of momentum to maintain the spout. Therefore, by staying close to this minimum flow condition, it is possible to perform a stable operation and to obtain energy savings not only in the heating of the gas but also in its displacement by blowers. In order to improve the operation of such processes, a study is carried out by implementing a simple optimizing control structure on a spouted bed experimental set-up. The air flow is regulated by a frequency inverter, at the speed of blower rotation. A PI controller was used and the set-point for the air flow rate is calculated on-line by a simple and well-known minimization method called Golden Section Search. This set-point is constantly updated with values very close to the actual minimum spout flow rate. To accomplish the calculations and data acquisitions, a microcomputer with an interface and an analog signal conditioner is used .

Effects of synbiotic food consumption on metabolic status of diabetic patients: a double-blind randomized cross-over controlled clinical trial.

Science.gov (United States)

Asemi, Zatollah; Khorrami-Rad, Ashraf; Alizadeh, Sabihe-Alsadat; Shakeri, Hossein; Esmaillzadeh, Ahmad

2014-04-01

We are aware of no study indicating the effects of synbiotic food consumption on metabolic profiles, inflammation and oxidative stress among diabetic patients. The aim of the current study was to investigate the effects of synbiotic food consumption on metabolic profiles, hs-CRP and biomarkers of oxidative stress in diabetic patients. This randomized double-blinded cross-over controlled clinical trial was performed among 62 diabetic patients aged 35-70 y. After a 2-wk run-in period, subjects were randomly assigned to consume either a synbiotic (n = 62) or control food (n = 62) for 6 weeks. A 3-week washout period was applied following which subjects were crossed over to the alternate treatment arm for an additional 6 weeks. The synbiotic food consisted of a probiotic viable and heat-resistant Lactobacillus sporogenes (1 × 10(7) CFU), 0.04 g inulin (HPX) as prebiotic with 0.38 g isomalt, 0.36 g sorbitol and 0.05 g stevia as sweetener per 1 g. Control food (the same substance without probiotic bacteria and prebiotic inulin) was packed in identical 9-gram packages. Patients were asked to consume the synbiotic and control foods three times a day. Fasting blood samples were taken at baseline and after a 6-wk intervention to measure metabolic profiles, hs-CRP and biomarkers of oxidative stress. Consumption of a synbiotic food, compared to the control, resulted in a significant decrease in serum insulin levels (changes from baseline: -1.75 ± 0.60 vs. +0.95 ± 1.09 μIU/mL, P = 0.03). Although we failed to find a significant effect of synbiotic food consumption on total- and LDL-cholesterol levels and HOMA-IR, the effects on FPG (22.3 vs. 4.2 mg/dL, P = 0.09), serum triglycerides (45.9 vs. 20.6 mg/dL, P = 0.08) and HDL-cholesterol levels (3.1 vs. -2 mg/dL, P = 0.06) tended to be significant. A significant reduction in serum hs-CRP levels (-1057.86 ± 283.74 vs. 95.40 ± 385.38 ng/mL, P = 0.01) was found following the consumption of synbiotic food compared with the

Femoral Test Bed for Impedance Controlled Surgical Instrumentation

Directory of Open Access Journals (Sweden)

Christian Brendle

2012-01-01

Full Text Available The risk for patients during the standard procedure of revision of cemented artificial hip joints is unsatisfactorily highdue to its high level of invasiveness and limited access to the operative field. To reduce this risk we are developing anImpedance Controlled Surgical Instrumentation (ICOS system, which aims to establish real-time control during a BoneCement (BC milling process. For this, the relationship between the thickness of the BC and its frequency-dependentelectrical impedance is used to estimate the residual BC thickness. The aim is to avoid unintended cutting of boneby detecting the passage of the BC/bone boundary layer by the milling head. In a second step, an estimation of theresidual BC thickness will be used to improve process control. As a first step towards demonstrating the feasibility ofour approach, presented here are experimental studies to characterize the BC permittivity and to describe the process indetail. The results show that the permittivity properties of BC are dominated by its polymethyl methacrylate (PMMAfraction. Thus, PMMA can be used as a substitute for future experiments. Furthermore, a Femoral Test Bed (FTB wasdesigned. Using this setup we show it is feasible to accurately distinguish between slightly different thicknesses of BC.

On the effect of cross sectional shape on incipient motion and deposition of sediments in fixed bed channels

Directory of Open Access Journals (Sweden)

Safari Mir-Jafar-Sadegh

2014-03-01

Full Text Available The condition of incipient motion and deposition are of the essential issues for the study of sediment transport. This phenomenon is of great importance to hydraulic engineers for designing sewers, drainage, as well as other rigid boundary channels. This is a study carried out with the objectives of describing the effect of cross-sectional shape on incipient motion and deposition of particles in rigid boundary channels. In this research work, the experimental data given by Loveless (1992 and Mohammadi (2005 are used. On the basis of the critical velocity approach, a new incipient motion equation for a V-shaped bottom channel and incipient deposition of sediment particles equations for rigid boundary channels having circular, rectangular, and U-shaped cross sections are obtained. New equations were compared to the other incipient motion equations. The result shows that the cross-sectional shape is an important factor for defining the minimum velocity for no-deposit particles. This study also distinguishes incipient motion of particles from incipient deposition for particles. The results may be useful for designing fixed bed channels with a limited deposition condition.

Synchronization control of cross-strict feedback hyperchaotic system based on cross active backstepping design

International Nuclear Information System (INIS)

Wang Jing; Gao Jinfeng; Ma Xikui

2007-01-01

This Letter presents a novel cross active backstepping design method for synchronization control of cross-strict feedback hyperchaotic system, in which the ordinary backstepping design is unavailable. The proposed control method, combining backstepping design and active control approach, extends the application of backstepping technique in chaos control. Based on this method, different combinations of controllers can be designed to meet the needs of different applications. The proposed method is applied to achieve chaos synchronization of two identical cross-strict feedback hyperchaotic systems. Also it is used to implement synchronization between cross-strict feedback hyperchaotic system and Roessler hyperchaotic system. Numerical examples illustrate the validity of the control method

Evaluation of ADCP apparent bed load velocity in a large sand-bed river: Moving versus stationary boat conditions

Science.gov (United States)

Jamieson, E.C.; Rennie, C.D.; Jacobson, R.B.; Townsend, R.D.

2011-01-01

Detailed mapping of bathymetry and apparent bed load velocity using a boat-mounted acoustic Doppler current profiler (ADCP) was carried out along a 388-m section of the lower Missouri River near Columbia, Missouri. Sampling transects (moving boat) were completed at 5- and 20-m spacing along the study section. Stationary (fixed-boat) measurements were made by maintaining constant boat position over a target point where the position of the boat did not deviate more than 3 m in any direction. For each transect and stationary measurement, apparent bed load velocity (vb) was estimated using ADCP bottom tracking data and high precision real-time kinematic (RTK) global positioning system (GPS). The principal objectives of this research are to (1) determine whether boat motion introduces a bias in apparent bed load velocity measurements; and (2) evaluate the reliability of ADCP bed velocity measurements for a range of sediment transport environments. Results indicate that both high transport (vb>0.6 m/s) and moving-boat conditions (for both high and low transport environments) increase the relative variability in estimates of mean bed velocity. Despite this, the spatially dense single-transect measurements were capable of producing detailed bed velocity maps that correspond closely with the expected pattern of sediment transport over large dunes. ?? 2011 American Society of Civil Engineers.

Bedding Improves Yellow-Poplar Growth on Fragipan Soils

Science.gov (United States)

John K. Francis

1979-01-01

Yellow-poplar can be grown on soils that have a shallow fragipan--but unless such sites are bedded, growth is likely to be extremely poor. In a Tennessee study, bedding increased height of planted yellow-poplar over 5 years, but fertilizer did not. Because of the cost of bedding and the availability of nonfragipan sites, it would ordinarily be better not to plant...

A mathematical model for supplying air-cooling for a building using a packed bed

Energy Technology Data Exchange (ETDEWEB)

Marewo, G.T. [Zimbabwe Univ., Mathematics Dept., Harare (Zimbabwe); Henwood, D.J. [School of Computing and Mathematical Sciences, Brighton (United Kingdom)

2006-01-15

The cooling system at the Harare International School uses a packed bed system for storing the coldness of the night-time to be used later for day-time air-conditioning. A two-phase mathematical model is described for the packed bed which includes heat dispersion in the fluid, and heat loss to the environment. This is in contrast to other studies, where at least one of these terms is neglected to simplify the mathematical model. A numerical method for obtaining a solution is proposed and implemented. Using measured inlet temperatures, the measured and predicted outlet temperatures of the bed show good trend agreement. The differences in detail are examined through sensitivity analyses for both the heat convection transfer and air velocity. It is apparent that adjusting these parameters can increase the agreement between the predicted and measured data. A parametric study for heat storage with various materials and bed sizes is given, which indicates how the code may be used as a tool for improving design and operational parameters. Practical application: A mathematical model of a packed bed is described; the bed is made up of fluid flowing over solid material with heat interchange between the two. The solid material is idealized as spheres and the fluid temperature is assumed uniform in a cross-section of the bed. The model includes heat interchange between the bed and its surrounding environment and allows for time varying fluid velocity. The input data is the inlet temperature to the bed, which may be measured. The comparison with measured data may be helpful to anyone attempting to develop and test a similar model. The sensitivity tests give an understanding of the significance of some of the parameters involved. The Appendix gives a mathematical statement of the problem and an outline of an approach to developing computer code for a numerical solution. (Author)

Why Don't You Go to Bed on Time? A Daily Diary Study on the Relationships between Chronotype, Self-Control Resources and the Phenomenon of Bedtime Procrastination.

Science.gov (United States)

Kühnel, Jana; Syrek, Christine J; Dreher, Anne

2018-01-01

Background: This daily diary study investigates the phenomenon of bedtime procrastination. Bedtime procrastination is defined as going to bed later than intended, without having external reasons for doing so. We highlight the role chronotype (interindividual differences in biological preferences for sleep-wake-times) plays for bedtime procrastination. Moreover, we challenge the view that bedtime procrastination is the result of a lack of self-regulatory resources by investigating momentary self-regulatory resources as a predictor of day-specific bedtime procrastination. Methods: One-hundred and eight employees working in various industries completed a general electronic questionnaire (to assess chronotype and trait self-control) and two daily electronic questionnaires (to assess momentary self-regulatory resources before going to bed and day-specific bedtime procrastination) over the course of five work days, resulting in 399 pairs of matched day-next-day measurements. Results: Results of multilevel regression analyses showed that later chronotypes (also referred to as evening types or 'owls') tended to report more bedtime procrastination on work days. Moreover, for late chronotypes, day-specific bedtime procrastination declined over the course of the work week. This pattern is in line with expectations derived from chronobiology and could not be explained by trait self-control. In addition, on evenings on which employees had less self-regulatory resources available before going to bed-compared to evenings on which they had more self-regulatory resources available before going to bed-employees showed lower bedtime procrastination. This finding contradicts the prevailing idea that bedtime procrastination is the result of a lack of self-regulatory resources. Conclusion: The findings of this study provide important implications for how bedtime procrastination should be positioned in the field of procrastination as self-regulatory failure and for how bedtime

ESTABLISHMENT OF AN ENVIRONMENTAL CONTROL TECHNOLOGY LABORATORY WITH A CIRCULATING FLUIDIZED-BED COMBUSTION SYSTEM

Energy Technology Data Exchange (ETDEWEB)

Wei-Ping Pan; Andy Wu; John T. Riley

2005-04-30

This report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period January 1, 2005 through March 31, 2005. The following tasks have been completed. First, the renovation of the new Combustion Laboratory is nearly complete, and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building is in the final stages. Second, the fabrication and manufacture of the CFBC Facility is being discussed with a potential contractor. Discussions with potential contactor regarding the availability of materials and current machining capabilities have resulted in the modification of the original designs. The selection of the fabrication contractor for the CFBC Facility is expected during the next quarter. Third, co-firing experiments conducted with coal and chicken waste have been initiated in the laboratory-scale simulated fluidized-bed facility. The experimental results from this study are presented in this report. Finally, the proposed work for the next quarter is described in this report.

Environmental management through sluice gated bed-dam: a revived strategy for the control of Anopheles fluviatilis breeding in streams

Science.gov (United States)

Sahu, S.S.; Gunasekaran, K.; Jambulingam, P.

2014-01-01

Background & objectives: Integrated vector management (IVM) emphasizes sustainable eco-friendly methods and minimal use of chemicals. In this context, the present study highlights the environmental control of breeding of Anopheles fluviatilis, the primary malaria vector, through water management in a natural stream in Koraput district, Odisha, India. Methods: The District Rural Development Agency (DRDA), Koraput, constructed two bed-dams across streams, one in Barigaon and the other in Pipalapodar village. The bed-dam in the former village was fitted with two sluice gates whereas the bed dam constructed in the latter village was without the sluice gate. The sluice gates were opened once in a week on a fixed day to flush out the water from the dam. Anopheles immatures were sampled systematically in the streams using a dipper for density measurement and species composition. Results: There was a reduction of 84.9 per cent in the proportion of positive dips for Anopheles larvae/pupae and a reduction of 98.4 per cent in immature density (number/dip) of An. fluviatilis in the experimental downstream compared to the control following opening of the sluice gates. Interpretation & conclusions: Our findins showed that opening of sluice gates of the bed-dam regularly once in a week resulted in the control of vector breeding in the downstream due to the flushing effect of the water released with a high flow from the bed-dam that stagnated water in the upstream. The outcome of the study encourages upscaling this measure to other areas, wherever feasible. PMID:25297364

Variability of bed mobility in natural, gravel-bed channels and adjustments to sediment load at local and reach scales

Science.gov (United States)

Thomas E. Lisle; Jonathan M. Nelson; John Pitlick; Mary Ann Madej; Brent L. Barkett

2000-01-01

Abstract - Local variations in boundary shear stress acting on bed-surface particles control patterns of bed load transport and channel evolution during varying stream discharges. At the reach scale a channel adjusts to imposed water and sediment supply through mutual interactions among channel form, local grain size, and local flow dynamics that govern bed mobility...

Balancing hydropower production and river bed incision in operating a run-of-river hydropower scheme along the River Po

Science.gov (United States)

Denaro, Simona; Dinh, Quang; Bizzi, Simone; Bernardi, Dario; Pavan, Sara; Castelletti, Andrea; Schippa, Leonardo; Soncini-Sessa, Rodolfo

2013-04-01

Water management through dams and reservoirs is worldwide necessary to support key human-related activities ranging from hydropower production to water allocation, and flood risk mitigation. Reservoir operations are commonly planned in order to maximize these objectives. However reservoirs strongly influence river geomorphic processes causing sediment deficit downstream, altering the flow regime, leading, often, to process of river bed incision: for instance the variations of river cross sections over few years can notably affect hydropower production, flood mitigation, water supply strategies and eco-hydrological processes of the freshwater ecosystem. The river Po (a major Italian river) has experienced severe bed incision in the last decades. For this reason infrastructure stability has been negatively affected, and capacity to derive water decreased, navigation, fishing and tourism are suffering economic damages, not to mention the impact on the environment. Our case study analyzes the management of Isola Serafini hydropower plant located on the main Po river course. The plant has a major impact to the geomorphic river processes downstream, affecting sediment supply, connectivity (stopping sediment upstream the dam) and transport capacity (altering the flow regime). Current operation policy aims at maximizing hydropower production neglecting the effects in term of geomorphic processes. A new improved policy should also consider controlling downstream river bed incision. The aim of this research is to find suitable modeling framework to identify an operating policy for Isola Serafini reservoir able to provide an optimal trade-off between these two conflicting objectives: hydropower production and river bed incision downstream. A multi-objective simulation-based optimization framework is adopted. The operating policy is parameterized as a piecewise linear function and the parameters optimized using an interactive response surface approach. Global and local

Uranium bed oxidation vacuum process system

International Nuclear Information System (INIS)

McLeland, H.L.

1977-01-01

Deuterium and tritium gases are occluded in uranium powder for release into neutron generator tubes. The uranium powder is contained in stainless steel bottles, termed ''beds.'' If these beds become damaged, the gases must be removed and the uranium oxidized in order not to be flammable before shipment to ERDA disposal grounds. This paper describes the system and methods designed for the controlled degassing and oxidation process. The system utilizes sputter-ion, cryo-sorption and bellows pumps for removing the gases from the heated source bed. Removing the tritium gas is complicated by the shielding effect of helium-3, a byproduct of tritium decay. This effect is minimized by incremental pressure changes, or ''batch'' processing. To prevent runaway exothermic reaction, oxidation of the uranium bed is also done incrementally, or by ''batch'' processing, rather than by continuous flow. The paper discusses in detail the helium-3 shielding effect, leak checks that must be made during processing, bed oxidation, degree of gas depletion, purity of gases sorbed from beds, radioactivity of beds, bed disposal and system renovation

The effect of physical training on patients with rheumatoid arthritis: changes in disease activity, muscle strength and aerobic capacity. A clinically controlled minimized cross-over study

DEFF Research Database (Denmark)

Lyngberg, K; Danneskiold-Samsøe, B; Halskov, O

1988-01-01

cross-over study the effect of graduated progressive training has been evaluated in 18 RA-patients with moderately active disease. The training was performed twice weekly with aerobic conditioning and strength exercises progressing to strenuous exercises over an 8-week period. The design was a crossover......For decades, physical training of rheumatoid arthritis (RA)-patients has been controversial, especially for patients with active disease. The aim of this study was to investigate whether RA-patients could receive graduated training without increasing the activity of the disease. In a controlled...... project with two groups obtained by minimisation. After training the patients had significantly fewer swollen joints than before. Training of the muscles acting over the swollen joints resulted in more than a 35% decrease in the number of swollen joints. The hemoglobin level increased significantly after...

Agglomeration of bed material: Influence on efficiency of biofuel fluidized bed boiler

Directory of Open Access Journals (Sweden)

Ryabov Georgy A.

2003-01-01

Full Text Available The successful design and operation of a fluidized bed combustor requires the ability to control and mitigate ash-related problems. The main ash-related problem of biomass filing boiler is agglomeration. The fluidized bed boiler with steam capacity of 66 t/h (4 MPa, 440 °C was started up at the Arkhangelsk Paper-Pi dp-Plant in 2001. This boiler was manufactured by the Russian companies "Energosofin" and "Belenergomash" and installed instead of the existing boiler with mechanical grate. Some constructional elements and steam drum of existing boiler remained unchanged. The primary air fan was installed past the common air fan, which supply part of the air into 24 secondary airports. First operating period shows that the bed material is expanded and then operator should increase the primary air rate, and the boiler efficiency dramatically decreases. Tills paper presents some results of our investigations of fuel, bed and fly ash chemical compositions and other characteristics. Special experiments were carried out to optimize the bed drain flow rate. The influence of secondly air supply improvement on mixing with the main flow and boiler efficiency are given.

Statistical description of flume experiments on mixed-size bed-load transport and bed armoring processes

Science.gov (United States)

Chen, D.; Zhang, Y.

2008-12-01

The objective of this paper is to describe the statistical properties of experiments on non-uniform bed-load transport as well as the mechanism of bed armoring processes. Despite substantial effort made over the last two decades, the ability to compute the bed-load flux in a turbulent system remains poor. The major obstacles include the poor understanding of the formation of armor lays on bed surfaces. Such a layer is much flow-resistible than the underlying material and therefore significantly inhibits sediment transport from the reach. To study the problem, we conducted a flume study for mixed sand/gravel sediments. We observed that aggregated sediment blocks were the most common characters in armor layers - the largest sizes resist hydraulic forces, while the smaller sizes add interlocking support and prevent loss of fine material through gaps between the larger particles. Fractional transport rates with the existing of armor layers were measured with time by sediment trapping method at the end of flume. To address the intermittent and time-varying behavior of bed-load transport during bed armoring processes, we investigated the probability distribution of the fractional bed-load transport rates, and the underlying dynamic model derived from the continuous time random walk framework. Results indicate that it is critical to consider the impact of armor layers when a flow is sufficient to move some of the finer particles and yet insufficient to move all the larger particles on a channel bed.

Development of a low-temperature two-stage fluidized bed incinerator for controlling heavy-metal emission in flue gases

International Nuclear Information System (INIS)

Peng, Tzu-Huan; Lin, Chiou-Liang; Wey, Ming-Yen

2014-01-01

This study develops a low-temperature two-stage fluidized bed system for treating municipal solid waste. This new system can decrease the emission of heavy metals, has low construction costs, and can save energy owing to its lower operating temperature. To confirm the treatment efficiency of this system, the combustion efficiency and heavy-metal emission were determined. An artificial waste containing heavy metals (chromium, lead, and cadmium) was used in this study. The tested parameters included first-stage temperature and system gas velocity. Results obtained using a thermogravimetric analyzer with a differential scanning calorimeter indicated that the first-stage temperature should be controlled to at least 400 °C. Although, a large amount of carbon monoxide was emitted after the first stage, it was efficiently consumed in the second. Loss of the ignition values of ash residues were between 0.005% and 0.166%, and they exhibited a negative correlation with temperature and gas velocity. Furthermore, the emission concentration of heavy metals in the two-stage system was lower than that of the traditional one-stage fluidized bed system. The heavy-metal emissions can be decreased by between 16% and 82% using the low-temperature operating process, silica sand adsorption, and the filtration of the secondary stage. -- Graphical abstract: Heavy-metal emission concentrations in flue gases under different temperatures and gas velocities (dashed line: average of the heavy-metal emission in flue gases in the one-stage fluidized-bed incinerator). Highlights: • Low temperature two-stage system is developed to control heavy metal. • The different first-stage temperatures affect the combustion efficiency. • Surplus CO was destroyed efficiently by the secondary fluidized bed combustor. • Metal emission in two-stage system is lower than in the traditional system. • Temperature, bed adsorption, and filtration are the main control mechanisms

Dynamic transition between fixed- and mobile-bed: mathematical and numerical aspects

Science.gov (United States)

Zugliani, Daniel; Pasqualini, Matteo; Rosatti, Giorgio

2017-04-01

Free-surface flows with high sediment transport (as debris flow or hyper-concentrated flow) are composed by a mixture of fluid and solid phase, usually water and sediment. When these flows propagate over loose beds, particles constituting the mixture of water and sediments strongly interact with the ones forming the bed, leading to erosion or deposition. However, there are lots of other situations when the mixture flows over rigid bedrocks or over artificially paved transects, so there is no mass exchange between bed and mixture. The two situations are usually referred to as, respectively, mobile- and fixed-bed conditions. From a mathematical point of view, the systems of Partial Differential Equations (PDEs) that describe these flows derive from mass and momentum balance of both phases, but, the two resulting PDEs systems are different. The main difference concerns the concentration: in the mobile-bed condition, the concentration is linked to the local flow conditions by means of a suitable rheological relation, while in the fixed-bed case, the concentration is an unknown of the problem. It is quite common that a free surface flow with high sediment transport, in its path, encounters both conditions. In the recent work of Rosatti & Zugliani 2015, the mathematical and numerical description of the transition between fixed- and mobile-bed was successfully resolved, for the case of low sediment transport phenomena, by the introduction of a suitable erodibility variable and satisfactory results were obtained. The main disadvantage of the approach is related to the erodibility variable, that changes in space, based on bed characteristics, but remains constant in time. However, the nature of the bed can change dynamically as result of deposition over fixed bed or high erosion over mobile bed. With this work, we extend the applicability of the mentioned approach to the more complex PDEs describing the hyper-concentrated flow. Moreover, we introduce a strategy that allows

Modeling N2O Reduction and Decomposition in a Circulating Fluidized bed Boiler

DEFF Research Database (Denmark)

Johnsson, Jan Erik; Åmand, Lars-Erik; Dam-Johansen, Kim

1996-01-01

The N2O concentration was measured in a circulating fluidized bed boiler of commercial size. Kinetics for N2O reduction by char and catalytic reduction and decomposition over bed material from the combustor were determined in a laboratory fixed bed reactor. The destruction rate of N2O in the comb......The N2O concentration was measured in a circulating fluidized bed boiler of commercial size. Kinetics for N2O reduction by char and catalytic reduction and decomposition over bed material from the combustor were determined in a laboratory fixed bed reactor. The destruction rate of N2O...... in the combustion chamber and the cyclone was calculated taking three mechanisms into account: Reduction by char, catalytic decomposition over bed material and thermal decomposition. The calculated destruction rate was in good agreement with the measured destruction of N2O injected at different levels in the boiler...

Intravesical Capsaicin in Patients with Detrusor Hyper-reflexia. A Placebo-controlled Cross-over Study

DEFF Research Database (Denmark)

Petersen, T; Nielsen, J B; Schrøder, H D

1999-01-01

to anticholinergic treatment underwent intravesical administration of 50 ml 2% lignocaine. followed by either 100 ml 1 mmol/l capsaicin or 100 ml physiological saline for 30 min. Cross-over to the alternative treatment took place after 4 weeks. Varying degrees of burning sensation were experienced by all but one...... patient during the capsaicin treatment and precluded the possibility of conducting studies of this type in a blind manner. No preference for capsaicin treatment was found, and micturition and VAS scores were unchanged after treatment with capsaicin. The mean volume of the contents of the bladder at which...... DH first appeared was 175 ml after saline and 195 ml after capsaicin (mean difference 20 ml with a 5% confidence interval from -25 to 65). Bladder biopsies taken 2 weeks after treatment with capsaicin showed more pronounced inflammation, superficial haemorrhage, squamous epithelial metaplasia...

Efficacy of topical Rose (Rosa damascena Mill.) oil for migraine headache: A randomized double-blinded placebo-controlled cross-over trial.

Science.gov (United States)

Niazi, Maria; Hashempur, Mohammad Hashem; Taghizadeh, Mohsen; Heydari, Mojtaba; Shariat, Abdolhamid

2017-10-01

To evaluate the effect of topical formulation of Rosa damascena Mill. (R. damascena) oil on migraine headache, applying syndrome diffrentiation model. Forty patients with migraine headache were randomly assigned to 2 groups of this double-blind, placebo-controlled cross-over trial. The patients were treated for the first 2 consecutive migraine headache attacks by topical R. damascena oil or placebo. Then, after one week of washout period, cross-over was done. Pain intensity of the patients' migraine headache was recorded at the beginnig and ten-sequence time schadule of attacks up to 24h. In addition, photophobia, phonophobia, and nausea and/or vomitting (N/V) of the patients were recorded as secondary outcomes. Finally, gathered data were analysed in a syndrome differentiation manner to assess the effect of R. damascena oil on Hot- and Cold-type migraine headache. Mean pain intensity of the patients' migraine headache in the different time-points after R. damascena oil or placebo use, was not significantly different. Additionally, regarding mean scores of N/V, photophobia, and phonophobia severity of the patients, no significant differences between the two groups were observed. Finally, applying syndrome differentiation model, the mean score of migraine headache pain intensity turned out to be significantly lower in patients with "hot" type migraine syndrome at in 30, 45, 60, 90, and 120min after R. damascena oil application compared to "cold" types (P values: 0.001, 0.001, <0.001, <0.001, and 0.02; respectively). It seems that syndrome differentiation can help in selection of patients who may benefit from the topical R. damascena oil in short-term relief of pain intensity in migraine headache. Further studies of longer follow-up and larger study population, however, are necessitated for more scientifically rigorous judgment on efficacy of R. damascena oil for patients with migraine headache. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bacillus cereus in free-stall bedding.

Science.gov (United States)

Magnusson, M; Svensson, B; Kolstrup, C; Christiansson, A

2007-12-01

To increase the understanding of how different factors affect the bacterial growth in deep sawdust beds for dairy cattle, the microbiological status of Bacillus cereus and coliforms in deep sawdust-bedded free stalls was investigated over two 14-d periods on one farm. High counts of B. cereus and coliforms were found in the entire beds. On average, 4.1 log(10) B. cereus spores, 5.5 log(10) B. cereus, and 6.7 log(10) coliforms per gram of bedding could be found in the upper layers of the sawdust likely to be in contact with the cows' udders. The highest counts of B. cereus spores, B. cereus, and coliforms were found in the bedding before fresh bedding was added, and the lowest immediately afterwards. Different factors of importance for the growth of B. cereus in the bedding material were explored in laboratory tests. These were found to be the type of bedding, pH, and the type and availability of nutrients. Alternative bedding material such as peat and mixtures of peat and sawdust inhibited the bacterial growth of B. cereus. The extent of growth of B. cereus in the sawdust was increased in a dose-dependent manner by the availability of feces. Urine added to different bedding material raised the pH and also led to bacterial growth of B. cereus in the peat. In sawdust, a dry matter content greater than 70% was needed to lower the water activity to 0.95, which is needed to inhibit the growth of B. cereus. In an attempt to reduce the bacterial growth of B. cereus and coliforms in deep sawdust beds on the farm, the effect of giving bedding daily or a full replacement of the beds was studied. The spore count of B. cereus in the back part of the free stalls before fresh bedding was added was 0.9 log units lower in stalls given daily bedding than in stalls given bedding twice weekly. No effect on coliform counts was found. Replacement of the entire sawdust bedding had an effect for a short period, but by 1 to 2 mo after replacement, the counts of B. cereus spores in the

Bed blockers: A study on the elderly patients in a teaching hospital in India

Directory of Open Access Journals (Sweden)

Praveen Kumar N

2010-07-01

Full Text Available A cross-sectional study of in-patients over the age of 60 years was conducted at district McGann Hospital, Shimoga on patients who were classified as bed blockers. Level of dependency and cognitive function of these patients were assessed using Barthel scale and Abbreviated mental test (AMT respectively. Median age of the study population was 67 years; majority of them were men. Most of them were admitted in the medical ward and the median time to be labeled as bed blocker was 32 days. These bed blockers were a weak group of patients with an average 3.1 pathology per case. Majority of them suffered from neurological disorders and cardiovascular disease. High level of dependence was noted with a mean Barthel score of 29.68 (Range 0 -100. Low levels of cognitive function was also noted among these patients with a mean AMT of 4.76 (Range 0 -10.These findings demonstrate that the bed blockers in McGann hospital suffer not only from genuine health problems but also have a high dependency level in activities of daily living which hamper their discharge to the community. Community based rehabilitation using an intersectoral approach may help at least the less dependent to return home.

Particle flow of ceramic breeder pebble beds in bi-axial compression experiments

International Nuclear Information System (INIS)

Hermsmeyer, S.; Reimann, J.

2002-01-01

Pebble beds of Tritium breeding ceramic material are investigated within the framework of developing solid breeder blankets for future nuclear fusion power plants. For the thermo-mechanical characterisation of such pebble beds, bed compression experiments are the standard tools. New bi-axial compression experiments on 20 and 30 mm high pebble beds show pebble flow effects much more pronounced than in previous 10 mm beds. Owing to the greater bed height, conditions are reached where the bed fails in cross direction and unhindered flow of the pebbles occurs. The paper presents measurements for the orthosilicate and metatitanate breeder materials that are envisaged to be used in a solid breeder blanket. The data are compared with calculations made with a Drucker-Prager soil model within the finite-element code ABAQUS, calibrated with data from other experiments. It is investigated empirically whether internal bed friction angles can be determined from pebble beds of the considered heights, which would simplify, and broaden the data base for, the calibration of the Drucker-Prager pebble bed models

Comparative study between fluidized bed and fixed bed reactors in methane reforming with CO2 and O2 to produce syngas

International Nuclear Information System (INIS)

Jing Qiangshan; Lou Hui; Mo Liuye; Zheng Xiaoming

2006-01-01

Reforming of methane with carbon dioxide and oxygen was investigated over Ni/MgO-SiO 2 catalysts using fixed bed and fluidized bed reactors. The conversions of CH 4 and CO 2 in a fluidized bed reactor were close to thermodynamic equilibrium. The activity and stability of the catalyst in the fixed bed reactor were lower than that in the fluidized bed reactor due to carbon deposition and nickel sintering. TGA and TEM techniques were used to characterize the spent catalysts. The results showed that a lot of whisker carbon was found on the catalyst in the rear of the fixed bed reactor, and no deposited carbon was observed on the catalysts in the fluidized bed reactor after reaction. It is suggested that this phenomenon is related to a permanent circulation of catalyst particles between the oxygen rich and oxygen free zones. That is, fluidization of the catalysts in the fluidized bed reactor favors inhibiting deposited carbon and thermal uniformity in the reactor

Transreplication and crossing over in Sordaria fimicola.

Science.gov (United States)

KITANI, Y; OLIVE, L S; EL-ANI, A S

1961-09-08

A study of the segregation of markers closely linked to the gray ascospore color locus in Sordaria fimicola reveals that there is a high incidence of crossing over very near the locus when it transreplicates, which is much more pronounced in 5:3 than in 6:2 asci. Also, a single 7:1 and several aberrant 4:4 asci are described. At a different spore color locus, transreplication yields only 6:2 ratios, while other spore color loci fail to transreplicate altogether

Implementation of an Electric Vehicle Test Bed Controlled by a Virtual Power Plant for Contributing to Regulating Power Reserves

DEFF Research Database (Denmark)

Marra, Francesco; Sacchetti, Dario; Pedersen, Anders Bro

2012-01-01

and communication interfaces, is able to respond in real-time to smart grid control signals. The EV test bed is equipped with a Lithium-ion battery pack, a Battery Management System (BMS), a charger and a Vehicle-to-Grid (V2G) unit for feeding power back to the grid. The designed solution serves......With the increased focus on Electric Vehicles (EV) research and the potential benefits they bring for smart grid applications, there is a growing need for an evaluation platform connected to the electricity grid. This paper addresses the design of an EV test bed, which using real EV components...... requests from the Danish TSO are used as a proof-of-concept, to demonstrate the EV test bed power response. Test results have proven the capability to respond to frequent power control requests and they reveal the potential EV ability for contributing to regulating power reserves....

Bed Utilisation in an Irish Regional Paediatric Unit – A Cross-Sectional Study Using the Paediatric Appropriateness Evaluation Protocol (PAEP

Directory of Open Access Journals (Sweden)

Coilín ÓhAiseadha

2016-11-01

Full Text Available Background Increasing demand for limited healthcare resources raises questions about appropriate use of inpatient beds. In the first paediatric bed utilisation study at a regional university centre in Ireland, we conducted a cross-sectional study to audit the utilisation of inpatient beds at the Regional Paediatric Unit (RPU in University Hospital Limerick (UHL, Limerick, Ireland and also examined hospital activity data, to make recommendations for optimal use of inpatient resources. Methods We used a questionnaire based on the paediatric appropriateness evaluation protocol (PAEP, modified and validated for use in the United Kingdom, to prospectively gather data regarding reasons for admission and for ongoing care after 2 days, from case records for all inpatients during 11 days in February (winter and 7 days in May–June (summer. We conducted bivariate and multivariate analysis to explore associations between failure to meet PAEP criteria and patient attributes including age, gender, admission outside of office hours, arrival by ambulance, and private health insurance. Inpatient bed occupancy and day ward activity were also scrutinised. Results Mean bed occupancy was 84.1%. In all, 12/355 (3.4%, 95% CI: 1.5%–5.3% of children failed to meet PAEP admission criteria, and 27/189 (14.3%, 95% CI: 9.3%–19.3% who were still inpatients after 2 days failed to meet criteria for ongoing care. 35/355 (9.9%, 95% CI: 6.8%–13.0% of admissions fulfilled only the PAEP criterion for intravenous medications or fluid replacement. A logistic regression model constructed by forward selection identified a significant association between failure to meet PAEP criteria for ongoing care 2 days after admission and admission during office hours (08.00–17.59 (P = .020, and a marginally significant association between this outcome and arrival by ambulance (P = .054. Conclusion At a mean bed occupancy of 84.1%, an Irish RPU can achieve 96.6% appropriate admissions

An Experiment of GMPLS-Based Dispersion Compensation Control over In-Field Fibers

Science.gov (United States)

Seno, Shoichiro; Horiuchi, Eiichi; Yoshida, Sota; Sugihara, Takashi; Onohara, Kiyoshi; Kamei, Misato; Baba, Yoshimasa; Kubo, Kazuo; Mizuochi, Takashi

As ROADMs (Reconfigurable Optical Add/Drop Multiplexers) are becoming widely used in metro/core networks, distributed control of wavelength paths by extended GMPLS (Generalized MultiProtocol Label Switching) protocols has attracted much attention. For the automatic establishment of an arbitrary wavelength path satisfying dynamic traffic demands over a ROADM or WXC (Wavelength Cross Connect)-based network, precise determination of chromatic dispersion over the path and optimized assignment of dispersion compensation capabilities at related nodes are essential. This paper reports an experiment over in-field fibers where GMPLS-based control was applied for the automatic discovery of chromatic dispersion, path computation, and wavelength path establishment with dynamic adjustment of variable dispersion compensation. The GMPLS-based control scheme, which the authors called GMPLS-Plus, extended GMPLS's distributed control architecture with attributes for automatic discovery, advertisement, and signaling of chromatic dispersion. In this experiment, wavelength paths with distances of 24km and 360km were successfully established and error-free data transmission was verified. The experiment also confirmed path restoration with dynamic compensation adjustment upon fiber failure.

Bed-level adjustments in the Arno River, central Italy

Science.gov (United States)

Rinaldi, Massimo; Simon, Andrew

1998-02-01

Two distinct phases of bed-level adjustment over the last 150 years are identified for the principal alluvial reaches of the Arno River (Upper Valdarno and Lower Valdarno). The planimetric configuration of the river in these reaches is the result of a series of hydraulic works (canalization, rectification, artificial cut-offs, etc.) carried out particularly between the 18th and the 19th centuries. Subsequently, a series of interventions at basin level (construction of weirs, variations in land use), intense instream gravel-mining after World War II, and the construction of two dams on the Arno River, caused widespread degradation of the streambed. Since about 1900, total lowering of the channel bed is typically between 2 and 4 m in the Upper Valdarno Reach and between 5 and 8 m in some areas of the Lower Valdarno Reach. Bed-level adjustments with time are analyzed for a large number of cross-sections and described by an exponential-decay function. This analysis identified the existence of two main phases of lowering: the first, triggered at the end of the past century; the second, triggered in the interval 1945-1960 and characterized by more intense degradation of the streambed. The first phase derived from changes in land-use and land-management practices. The second phase is the result of the superimposition of two factors: intense instream mining of gravel, and the construction of the Levane and La Penna dams.

[Genetic control of mitotic crossing-over in yeasts. III. Induction by 8-methoxypsoralen and long-wave UV irradiation (lambda=365 nm)].

Science.gov (United States)

Fedorova, I V; Marfin, S V

1982-02-01

The lethal effect of 8-methoxypsoralen (8-MOP) plus 365 nm light has been studied in haploid radiosensitive strains of Saccharomyces cerevisiae. The diploid of wild type and the diploid homozygous for the rad2 mutation (this mutation blocks the excision of UV-induced pyrimidine dimers) were more resistant to the lethal effect of 8-MOP plus 365 nm light than the haploid of wild type and rad2 haploid, respectively. The diploid homozygous for rad54 mutation (the mutation blocks the repair of double-strand breaks in DNA) was more sensitive than haploid rad54. The method of repeated irradiation allowed to study the capacity of radiosensitive diploids to remove monoadducts induced by 8-MOP in DNA. This process was very effective in diploids of wild type and in the rad54 rad54 diploid, while the rad2 rad2 diploid was characterized by nearly complete absence of monoadduct excision. The study of mitotic crossing over and mitotic segregation in yeast diploids, containing a pair of complementing alleles of the ade2 gene (red/pink) has shown a very high recombinogenic effect of 8-MOP plus 365 nm light. The rad2 mutation slightly increased the frequency of mitotic segregation and mitotic crossing over. The rad54 mutation decreased the frequency of mitotic segregation and entirely suppressed mitotic crossing over. The method of repeated irradiation showed that the cross-links, but not monoadducts, are the main cause of high recombinogenic effect of 8-MOP plus 365 nm light. The possible participation of different repair systems in recombinational processes induced by 8-MOP in yeast cells is discussed.

Model for boiling and dryout in particle beds

International Nuclear Information System (INIS)

Lipinski, R.J.

1982-06-01

Over the last ten years experiments and modeling of dryout in particle beds have produced over fifty papers. Considering only volume-heated beds, over 250 dryout measurements have been made, and are listed in this work. In addition, fifteen models to predict dryout have been produced and are discussed. A model is developed in this report for one-dimensional boiling and dryout in a porous medium. It is based on conservation laws for mass, momentum, and energy. The initial coupled differential equations are reduced to a single first-order differential equation with an algebraic equation for the upper boundary condition. The model includes the effects of both laminar and turbulent flow, two-phase friction, and capillary force. The boundary condition at the bed bottom includes the possibility of inflowing liquid and either an adiabatic or a bottom-cooled support structure. The top of the bed may be either channeled or subcooled. In the first case the channel length and the saturation at the base of the channels are predicted. In the latter case, a criterion for penetration of the subcooled zone by channels is obtained

Forces on stationary particles in near-bed turbulent flows

Science.gov (United States)

Schmeeckle, Mark W.; Nelson, Jonathan M.; Shreve, Ronald L.

2007-06-01

In natural flows, bed sediment particles are entrained and moved by the fluctuating forces, such as lift and drag, exerted by the overlying flow on the particles. To develop a better understanding of these forces and the relation of the forces to the local flow, the downstream and vertical components of force on near-bed fixed particles and of fluid velocity above or in front of them were measured synchronously at turbulence-resolving frequencies (200 or 500 Hz) in a laboratory flume. Measurements were made for a spherical test particle fixed at various heights above a smooth bed, above a smooth bed downstream of a downstream-facing step, and in a gravel bed of similarly sized particles as well as for a cubical test particle and 7 natural particles above a smooth bed. Horizontal force was well correlated with downstream velocity and not correlated with vertical velocity or vertical momentum flux. The standard drag formula worked well to predict the horizontal force, but the required value of the drag coefficient was significantly higher than generally used to model bed load motion. For the spheres, cubes, and natural particles, average drag coefficients were found to be 0.76, 1.36, and 0.91, respectively. For comparison, the drag coefficient for a sphere settling in still water at similar particle Reynolds numbers is only about 0.4. The variability of the horizontal force relative to its mean was strongly increased by the presence of the step and the gravel bed. Peak deviations were about 30% of the mean force for the sphere over the smooth bed, about twice the mean with the step, and 4 times it for the sphere protruding roughly half its diameter above the gravel bed. Vertical force correlated poorly with downstream velocity, vertical velocity, and vertical momentum flux whether measured over or ahead of the test particle. Typical formulas for shear-induced lift based on Bernoulli's principle poorly predict the vertical forces on near-bed particles. The

Discrete Element Modeling of the Mobilization of Coarse Gravel Beds by Finer Gravel Particles

Science.gov (United States)

Hill, K. M.; Tan, D.

2012-12-01

Recent research has shown that the addition of fine gravel particles to a coarse bed will mobilize the coarser bed, and that the effect is sufficiently strong that a pulse of fine gravel particles can mobilize an impacted coarser bed. Recent flume experiments have demonstrated that the degree of bed mobilization by finer particles is primarily dependent on the particle size ratio of the coarse and fine particles, rather than absolute size of either particle, provided both particles are sufficiently large. However, the mechanism behind the mobilization is not understood. It has previously been proposed that the mechanism is driven by a combination of geometric effects and hydraulic effects. For example, it has been argued that smaller particles fill in gaps along the bed, resulting in a smoother bed over which the larger particles are less likely to be disentrained and a reduced near-bed flow velocity and subsequent increased drag on protruding particles. Altered near-bed turbulence has also been cited as playing an important role. We perform simulations using the discrete element method with one-way fluid-solid coupling to conduct simulations of mobilization of a gravel bed by fine gravel particles. By independently and artificially controlling average and fluctuating velocity profiles, we systematically investigate the relative role that may be played by particle-particle interactions, average near-bed velocity profiles, and near-bed turbulence statistics. The simulations indicate that the relative importance of these mechanisms changes with the degree of mobilization of the bed. For higher bed mobility similar to bed sheets, particle-particle interactions, plays a significant role in an apparent rheology in the bed sheets, not unlike that observed in a dense granular flow of particles of different sizes. For conditions closer to a critical shear stress for bedload transport, the near-bed velocity profiles and turbulence statistics become increasingly important.

Design and adjustment on test bed of replacing subassembly machine control system for China experimental fast reactor

International Nuclear Information System (INIS)

Dong Shengguo; Ma Hongsheng; Zhao Lixia

2008-01-01

The present research concerns in the design and adjustment of replacing sub- assembly machine control system of China Experimental Fast Reactor. The design of replacing subassembly machine control system adopts some electric equipments, such as programmable controllers, digital DC drivers. The designed control system was adjusted on the test bed. The results indicate that the operation of the control system is steady and reliable, and designed control system can meet the needs of the design specification. (authors)

Optimal oxygen feeding policy to maximize the production of Maleic anhydride in unsteady state fixed bed catalytic reactors

Directory of Open Access Journals (Sweden)

E. Ali

2017-07-01

Full Text Available The effect of different oxygen feeding scenarios in a fixed bed reactor for the production of Maleic anhydride (MA is studied. Two reactor configurations were examined. In the first configuration, a cross flow reactor (CFR with 4 discrete feeding points is considered. Another configuration is the conventional packed-bed reactor (PBR with a single feed. Nonlinear Model Predictive Controller (NLMPC was used as optimal controller to operate the CFR in dynamic mode and to optimize the multiple feed dosages in order to enhance the MA yield. The simulation results indicated that different combinations of the four feed ratios can operate the reactor at the best value for the yield provided the first feeding point is kept as low as possible. For the packed bed reactor configuration, a single oxygen feed is considered and is optimized transiently by NLMPC. The simulation outcomes showed that the reactor performance in terms of the produced MA mole fraction can also be enhanced to the same magnitude obtained by CFR configuration. This improvement requires decreasing the oxygen ratio in the reactor single feed by 70%.

Investigation of Facies Types and Associations of Kuhlan Red Bed Formation in NW Yemen: A New Hypothesis for Origin and Depositional Environment

Directory of Open Access Journals (Sweden)

Mohammed A. Al-Wosabi

2006-06-01

Full Text Available Varieties of thirteen facies types were recognized in the Kuhlan Formation represented by red bed siliciclastic sequences of argillaceous sediments. Examination of the Kuhlan stratigraphic column included sequence relationships, lithology, sedimentary characters, structures and petrography of the dominant rock types. These facies types are grouped in three distinct associations of facies. The lower unit A comprises association of facies (Distal turbidites represented by alternates of turbidity sequences including sandstone, siltstone and thick shale beds. These facies types confirm a regressive depositional environment in deep marine shelf conditions. There are three facies types which are identified as massive sandstone, cross-bedded sandstone and pebbly sandstone facies. The middle unit B association of facies (Proximal turbedites represents glaciomarine sequences displaying high lateral and vertical facies changes of glacioturbidite sediment alternates with diamictites and tillite beds. The sequences are affected by eustatic and eustatism of the glacial advance and retreat. This unit B includes eight types of facies. These are identified as; tillite, massive diamictites, stratified diamictites, laminated siltstone/shale, deformed siltstone/mudstone, graded rhythmic siltstone, massive conglomerate and cross-stratified sandy conglomerate facies. The upper unit C association of facies is represented by shallow marine shelf sequences displaying very thick massive and locally cross-bedded sand bar sandstone overlying the laminated siltstone/shale interbeds. The upward gradual changes in mineralogical composition and color confirms the start of marine transgression and later deposited platform Amran Group. Mineralogical composition of Kuhlan sandstone displays impure dirty rocks consisting of more than 30% of argillaceous matrix, 50% of cristobalite and quartz grains, more than 10% of ferruginous cement and 10% of detrital iron oxide grains, potash

Self-pacing study of faces of different races: metacognitive control over study does not eliminate the cross-race recognition effect.

Science.gov (United States)

Tullis, Jonathan G; Benjamin, Aaron S; Liu, Xiping

2014-08-01

People often recognize same-race faces better than other-race faces. This cross-race effect (CRE) has been proposed to arise in part because learners devote fewer cognitive resources to encode faces of social out-groups. In three experiments, we evaluated whether learners' other-race mnemonic deficits are due to "cognitive disregard" during study and whether this disregard is under metacognitive control. Learners studied each face either for as long as they wanted (the self-paced condition) or for the average time taken by a self-paced learner (the fixed-rate condition). Self-paced learners allocated equal amounts of study time to same-race and other-race faces, and having control over study time did not change the size of the CRE. In the second and third experiments, both self-paced and fixed-rate learners were given instructions to "individuate" other-race faces. Individuation instructions caused self-paced learners to allocate more study time to other-race faces, but this did not significantly reduce the size of the CRE, even for learners who reported extensive contact with other races. We propose that the differential processing that people apply to faces of different races and the subsequent other-race mnemonic deficit are not due to learners' strategic cognitive disregard of other-race faces.

The Grain-size Patchiness of Braided Gravel-Bed Streams - example of the Urumqi River (northeast Tian Shan, China)

Science.gov (United States)

Guerit, L.; Barrier, L.; Narteau, C.; Métivier, F.; Liu, Y.; Lajeunesse, E.; Gayer, E.; Meunier, P.; Malverti, L.; Ye, B.

2014-02-01

In gravel-bed rivers, sediments are often sorted into patches of different grain-sizes, but in braided streams, the link between this sorting and the channel morpho-sedimentary elements is still unclear. In this study, the size of the bed sediment in the shallow braided gravel-bed Urumqi River is characterized by surface-count and volumetric sampling methods. Three morpho-sedimentary elements are identified in the active threads of the river: chutes at flow constrictions, which pass downstream to anabranches and bars at flow expansions. The surface and surface-layer grain-size distributions of these three elements show that they correspond to only two kinds of grain-size patches: (1) coarse-grained chutes, coarser than the bulk river bed, and (2) finer-grained anabranches and bars, consistent with the bulk river bed. In cross-section, the chute patches are composed of one coarse-grained top layer, which can be interpreted as a local armour layer overlying finer deposits. In contrast, the grain size of the bar-anabranch patches is finer and much more homogeneous in depth than the chute patches. Those patches, which are features of lateral and vertical sorting associated to the transport dynamics that build braided patterns, may be typical of active threads in shallow gravel-bed rivers and should be considered in future works on sorting processes and their geomorphologic and stratigraphic results.

Debris bed cooling following an HCDA in a fast reactor. Final report

International Nuclear Information System (INIS)

Abdel-Khalik, S.I.

1983-01-01

Natural convection within simulated core debris beds has been experimentally and theoretically investigated. The effect of heating method on bed behavior has been found to be important. For directly-heated beds, variations of the downward and upward power fraction and Nusselt numbers with bed loading, power density, particle size, overlying fluid layer height and top surface boundary condition have been determined. Generalized correlations for the upward and downward Nusselt numbers as functions of the internal Rayleigh number have been obtained. Particle tracing techniques have been used to visualize the flow patterns within the bed and overlying fluid layer. The temperature distributions within the bed and overlying fluid layer have also been measured. The experimental data have been compared with COMMIX-lA predictions. Poor agreement has been obtained for both the integral quantities, i.e. downward and upward power fractions and Nusselt numbers, as well as the steady state velocity and temperature distributions. The code does not correctly predict either the magnitude or even the trend of the data

How should we best estimate the mean recency duration for the BED method?

Directory of Open Access Journals (Sweden)

John Hargrove

Full Text Available BED estimates of HIV incidence from cross-sectional surveys are obtained by restricting, to fixed time T, the period over which incidence is estimated. The appropriate mean recency duration (Ω(T then refers to the time where BED optical density (OD is less than a pre-set cut-off C, given the patient has been HIV positive for at most time T. Five methods, tested using data for postpartum women in Zimbabwe, provided similar estimates of Ω(T for C = 0.8: i The ratio (r/s of the number of BED-recent infections to all seroconversions over T = 365 days: 192 days [95% CI 168-216]. ii Linear mixed modeling (LMM: 191 days [95% CI 174-208]. iii Non-linear mixed modeling (NLMM: 196 days [95% CrI 188-204]. iv Survival analysis (SA: 192 days [95% CI 168-216]. Graphical analysis: 193 days. NLMM estimates of Ω(T--based on a biologically more appropriate functional relationship than LMM--resulted in best fits to OD data, the smallest variance in estimates of VT, and best correspondence between BED and follow-up estimates of HIV incidence, for the same subjects over the same time period. SA and NLMM produced very similar estimates of Ω(T but the coefficient of variation of the former was .3 times as high. The r/s method requires uniformly distributed seroconversion events but is useful if data are available only from a single follow-up. The graphical method produces the most variable results, involves unsound methodology and should not be used to provide estimates of Ω(T. False-recent rates increased as a quadratic function of C: for incidence estimation C should thus be chosen as small as possible, consistent with an adequate resultant number of recent cases, and accurate estimation of Ω(T. Inaccuracies in the estimation of Ω(T should not now provide an impediment to incidence estimation.

Heat exchanger support apparatus in a fluidized bed

Science.gov (United States)

Lawton, Carl W.

1982-01-01

A heat exchanger is mounted in the upper portion of a fluidized combusting bed for the control of the temperature of the bed. A support, made up of tubes, is extended from the perforated plate of the fluidized bed up to the heat exchanger. The tubular support framework for the heat exchanger has liquid circulated therethrough to prevent deterioration of the support.

Mathematical Modelling of Catalytic Fixed-Bed Reactor for Carbon Dioxide Reforming of Methane over Rh/Al2O3 Catalyst

Directory of Open Access Journals (Sweden)

New Pei Yee

2008-04-01

Full Text Available A one-dimensional mathematical model was developed to simulate the performance of catalytic fixed bedreactor for carbon dioxide reforming of methane over Rh/Al2O3 catalyst at atmospheric pressure. The reactionsinvolved in the system are carbon dioxide reforming of methane (CORM and reverse water gas shiftreaction (RWGS. The profiles of CH4 and CO2 conversions, CO and H2 yields, molar flow rate and molefraction of all species as well as reactor temperature along the axial bed of catalyst were simulated. In addition,the effects of different reactor temperature on the reactor performance were also studied. The modelscan also be applied to analyze the performances of lab-scale micro reactor as well as pilot-plant scale reactorwith certain modifications and model verification with experimental data. © 2008 BCREC UNDIP. All rights reserved.[Received: 20 August 2008; Accepted: 25 September 2008][How to Cite: N.A.S. Amin, I. Istadi, N.P. Yee. (2008. Mathematical Modelling of Catalytic Fixed-Bed Reactor for Carbon Dioxide Reforming of Methane over Rh/Al2O3 Catalyst. Bulletin of Chemical Reaction Engineering and Catalysis, 3 (1-3: 21-29. doi:10.9767/bcrec.3.1-3.19.21-29

Petrology and geochemistry of samples from bed-contact zones in Tunnel Bed 5, U12g-Tunnel, Nevada Test Site

International Nuclear Information System (INIS)

Connolly, J.R.; Keil, K.; Mansker, W.L.; Allen, C.C.; Husler, J.; Lowy, R.; Fortney, D.R.; Lappin, A.R.

1984-10-01

This report summarizes the detailed geologic characterization of samples of bed-contact zones and surrounding nonwelded bedded tuffs, both within Tunnel Bed 5, that are exposed in the G-Tunnel complex beneath Rainier Mesa on the Nevada Test Site (NTS). Original planning studies treated the bed-contact zones in Tunnel Bed 5 as simple planar surfaces of relatively high permeability. Detailed characterization, however, indicates that these zones have a finite thickness, are depositional in origin, vary considerably over short vertical and horizontal distances, and are internally complex. Fluid flow in a sequence of nonwelded zeolitized ash-flow or bedded tuffs and thin intervening reworked zones appears to be a porous-medium phenomenon, regardless of the presence of layering. There are no consistent differences in either bulk composition or detailed mineralogy between bedded tuffs and bed-contact zones in Tunnel Bed 5. Although the original bulk composition of Tunnel Bed 5 was probably peralkaline, extensive zeolitization has resulted in a present peraluminous bulk composition of both bedded tuffs and bed-contact zones. The major zeolite present, clinoptilolite, is intermediate (Ca:K:Na = 26:35:39) and effectively uniform in composition. This composition is similar to that of clinoptilolite from the tuffaceous beds of Calico Hills above the static water level in hole USW G-1, but somewhat different from that reported for zeolites from below the static water level in USW G-2. Tunnel Bed 5 also contains abundant hydrous manganese oxides. The similarity in composition of the clinoptilolites from Tunnel Bed 5 and those above the static water level at Yucca Mountain indicates that many of the results of nuclide-migration experiments in Tunnel Bed 5 would be transferrable to zeolitized nonwelded tuffs above the static water level at Yucca Mountain

Cross over of recurrence networks to random graphs and random ...

Indian Academy of Sciences (India)

2017-01-27

Jan 27, 2017 ... that all recurrence networks can cross over to random geometric graphs by adding sufficient amount of noise to .... municative [19] or social [20], deviate from the random ..... He has shown that the spatial effects become.

Effectiveness of two different HDR brachytherapy regimens with the same BED value in cervical cancer

Directory of Open Access Journals (Sweden)

Rajesh Vashistha

2010-07-01

Full Text Available Purpose: To analyze the effectiveness of biologically effective dose (BED in two different regimens of HDR brachytherapy keeping the same total BED to point A and to compare the relationship of overall treatment time in terms of local control and bladder and rectal complications.Material and methods: The study included two groups comprising a total of 90 cervical cancer patients who underwent external beam radiotherapy (EBRT followed by HDR intracavitary brachytherapy (ICBT. EBRT treatment was delivered by a Co-60 teletherapy unit to a prescribed dose of 45 Gy with 1.8 Gy per fraction in 25 fractions over a period of five weeks. Parallel opposed anterior–posterior (AP/PA fields with no central shielding were used, followed by the HDR ICBT dose, to point A, of either two fractions of 9.5 Gy with a gap of 10 days, or three fractions of 7.5 Gy with a gap of 7 days between the fractions. Gemcitabine (dose of 150 mg/m2 was given weekly to all the patients as a radiosensitizer. The calculate BED3 to point A was almost the same in both groups to keep the same late complication rates. The doses, and BED10 and BED3, were calculated at different bladder and rectal point as well as at the lymphatictrapezoid points. During and after treatment patients were evaluated for local control and complications for 24 months.Results and Conclusions: Doses and BEDs at different bladder, rectal and lymphatic trapezoid points, local control, and complications in both HDR ICBT groups did not have statistically significant differences (p > 0.05. Both HDR ICBT schedules are well tolerable and equally effective.

Granule size control and targeting in pulsed spray fluid bed granulation.

Science.gov (United States)

Ehlers, Henrik; Liu, Anchang; Räikkönen, Heikki; Hatara, Juha; Antikainen, Osmo; Airaksinen, Sari; Heinämäki, Jyrki; Lou, Honxiang; Yliruusi, Jouko

2009-07-30

The primary aim of the study was to investigate the effects of pulsed liquid feed on granule size. The secondary aim was to increase knowledge of this technique in granule size targeting. Pulsed liquid feed refers to the pump changing between on- and off-positions in sequences, called duty cycles. One duty cycle consists of one on- and off-period. The study was performed with a laboratory-scale top-spray fluid bed granulator with duty cycle length and atomization pressure as studied variables. The liquid feed rate, amount and inlet air temperature were constant. The granules were small, indicating that the powder has only undergone ordered mixing, nucleation and early growth. The effect of atomizing pressure on granule size depends on inlet air relative humidity, with premature binder evaporation as a reason. The duty cycle length was of critical importance to the end product attributes, by defining the extent of intermittent drying and rewetting. By varying only the duty cycle length, it was possible to control granule nucleation and growth, with a wider granule size target range in increased relative humidity. The present study confirms that pulsed liquid feed in fluid bed granulation is a useful tool in end product particle size targeting.

A review of some parameters involved in fluidized bed bioreactors

Energy Technology Data Exchange (ETDEWEB)

Wright, P.C. [School of Chemical Engineering and Industrial Chemistry, The Univ. of New South Wales, Sydney (Australia); Raper, J.A. [School of Chemical Engineering and Industrial Chemistry, The Univ. of New South Wales, Sydney (Australia)

1996-02-01

Three-phase fluidized bed bioreactors have advantages over conventional chemical reaction systems. There is a lack of agreement over most major operational conditions, and a wide range of design variables are open to question. A large body of recent work in the field has been reviewed, with a degree of historical comparison and discussion. It has been found that aspects of fluidized bed biofilm reactors of vital importance include: choice of solid media, gas and liquid loadings, bacterial type and reactor mechanical design. A large proportion of the work in the field of three-phase fluidization is non-biologically specific, or not tested on a bacterially inoculated system. The majority of three-phase fluidized bed bioreactor work is in the field of water treatment. Although this work has highlighted the potential for use of bio-fluidized beds for this application, there are still specific problems hinderin the large scale industrial acceptance of three-phase fluidized bed bioreactors. (orig.)

Dehydration studies using a novel multichamber microscale fluid bed dryer with in-line near-infrared measurement

DEFF Research Database (Denmark)

Räsänen, Eetu; Rantanen, Jukka; Mannermaa, Jukka-Pekka

2003-01-01

The purpose of this research was to study the effect of two process parameters (temperature and moisture content) on dehydration behavior of different materials using a novel multichamber microscale fluid bed dryer with a process air control unit and in-line near-infrared (NIR) spectroscopy....... The materials studied were disodium hydrogen phosphates with three different levels of hydrate water and wet theophylline granules. Measured process parameters of fluid bed drying were logged, including in-line NIR signals. Off-line analyses consisted of X-ray powder diffraction patterns, Fourier transform NIR...... spectra and moisture contents of studied materials. During fluid bed drying, the stepwise dehydration of materials was observed by the water content difference of inlet and outlet air, the pressure difference over the bed, and the in-line NIR spectroscopy. The off-line analysis confirmed the state...

A double-blind placebo-controlled cross-over clinical trial of DONepezil In Posterior cortical atrophy due to underlying Alzheimer's Disease: DONIPAD study.

Science.gov (United States)

Ridha, Basil H; Crutch, Sebastian; Cutler, Dawn; Frost, Christopher; Knight, William; Barker, Suzie; Epie, Norah; Warrington, Elizabeth K; Kukkastenvehmas, Riitta; Douglas, Jane; Rossor, Martin N

2018-05-01

The study investigated whether donepezil exerts symptomatic benefit in patients with posterior cortical atrophy (PCA), an atypical variant of Alzheimer's disease. A single-centre, double-blind, placebo-controlled, cross-over clinical trial was performed to assess the efficacy of donepezil in patients with PCA. Each patient received either donepezil (5 mg once daily in the first 6 weeks and 10 mg once daily in the second 6 weeks) or placebo for 12 weeks. After a 2-week washout period, each patient received the other treatment arm during the following 12 weeks followed by another 2-week washout period. The primary outcome was the Mini-Mental State Examination (MMSE) at 12 weeks. Secondary outcome measures were five neuropsychological tests reflecting parieto-occipital function. Intention-to-treat analysis was used. For each outcome measure, carry-over effects were first assessed. If present, then analysis was restricted to the first 12-week period. Otherwise, the standard approach to the analysis of a 2 × 2 cross-over trial was used. Eighteen patients (13 females) were recruited (mean age 61.6 years). There was a protocol violation in one patient, who subsequently withdrew from the study due to gastrointestinal side effects. There was statistically significant (p effect on MMSE. Therefore, the analysis of treatment effect on MMSE was restricted to the first 12-week period. Treatment effect at 6 weeks was statistically significant (difference = 2.5 in favour of donepezil, 95% CI 0.1 to 5.0, p effect at 12 weeks was close, but not statistically significant (difference = 2.0 in favour of donepezil, 95% CI -0.1 to 4.5, p > 0.05). There were no statistically significant treatment effects on any of the five neuropsychological tests, except for digit span at 12 weeks (higher by 0.5 digits in favour of placebo, 95% CI 0.1 to 0.9). Gastrointestinal side effects occurred most frequently, affecting 13/18 subjects (72%), and were the cause of study discontinuation in one

Magic with moulds: Meiotic and mitotic crossing over in Neurospora ...

Indian Academy of Sciences (India)

2006-02-16

Feb 16, 2006 ... Home; Journals; Journal of Biosciences; Volume 31; Issue 1. Commentary: Magic with moulds: Meiotic and mitotic crossing over in Neurospora inversions and duplications. Durgadas P Kasbekar. Volume 31 Issue 1 March 2006 pp 3-4 ...

Research on application of burnable poison in pebble bed HTR

International Nuclear Information System (INIS)

Wei Chunlin; Zhang Jian; Shan Wenzhi; Jing Xingqing

2013-01-01

Burnable poison in fuel ball was used in pebble bed high-temperature gas-cooled reactor (HTR) to optimize the shape and the peak factor of power distribution in certain conditions. Two options are available and evaluated, that is the homogeneous burnable poison in graphite matrix and burnable poison particles (BPPs) in fuel balls. Due to the absorption cross section of "1"0B, the depletion speed for homogeneous burnable poison is very fast, and difficult to control, on the other side, the depletion speed of BPPs can be optimized respecting to its size, and better shape and peak value of power distribution can be achieved. (authors)

Bed Bug Information Clearinghouse

Science.gov (United States)

Its purpose is to help states, communities, and consumers in efforts to prevent and control bed bug infestations. Currently includes only reviewed material from federal/state/local government agencies, extension services, and universities.

Changes in the channel-bed level of the western Carpathian rivers over the last 40years

Science.gov (United States)

Kijowska-Strugała, Małgorzata; Bucała-Hrabia, Anna

2017-04-01

(3.2 cm/year) was dominated. Two main factors determine changes in the position of the rivers channel beds: natural (floods, tributaries, type of the channel bed substrate) and anthropogenic (control works in the channel, extraction gravels, reservoir backwater. The deep erosion observed in the Carpathians rivers in the last decade is also associated with changes in land use that have increased due to the economic transformation of the country, and in recent years, the Polish accession to the EU.

Avoiding Carbon Bed Hot Spots in Thermal Process Off-Gas Systems

International Nuclear Information System (INIS)

Soelberg, Nick; Enneking, Joe

2011-01-01

Mercury has had various uses in nuclear fuel reprocessing and other nuclear processes, and so is often present in radioactive and mixed (radioactive and hazardous) wastes. Test programs performed in recent years have shown that mercury in off-gas streams from processes that treat radioactive wastes can be controlled using fixed beds of activated sulfur-impregnated carbon, to levels low enough to comply with air emission regulations such as the Hazardous Waste Combustor (HWC) Maximum Achievable Control Technology (MACT) standards. Carbon bed hot spots or fires have occurred several times during these tests, and also during a remediation of tanks that contained mixed waste. Hot spots occur when localized areas in a carbon bed become heated to temperatures where oxidation occurs. This heating typically occurs due to heat of absorption of gas species onto the carbon, but it can also be caused through external means such as external heaters used to heat the carbon bed vessel. Hot spots, if not promptly mitigated, can grow into bed fires. Carbon bed hot spots and fires must be avoided in processes that treat radioactive and mixed waste. Hot spots are detected by (a) monitoring in-bed and bed outlet gas temperatures, and (b) more important, monitoring of bed outlet gas CO concentrations. Hot spots are mitigated by (a) designing for appropriate in-bed gas velocity, for avoiding gas flow maldistribution, and for sufficient but not excessive bed depth, (b) appropriate monitoring and control of gas and bed temperatures and compositions, and (c) prompt implementation of corrective actions if bed hot spots are detected. Corrective actions must be implemented quickly if bed hot spots are detected, using a graded approach and sequence starting with corrective actions that are simple, quick, cause the least impact to the process, and are easiest to recover from.

Fluid bed dryer and Aeropep solidification system

International Nuclear Information System (INIS)

1975-01-01

Performance measurements were made on the model of the Fluidized-bed Calciner developed by Aerojet Liquid Rocket Co. The measurements were made over the period August 11-19, 1975, at the Sacramento location of the calciner. The purpose of the tests was to evaluate the performance of the ALRC Fluidized Bed Concentrator for the processing of simulated waste containing realistic concentrations and chemical forms of radioiodine. (auth)

Particle bed reactor modeling

Science.gov (United States)

Sapyta, Joe; Reid, Hank; Walton, Lew

The topics are presented in viewgraph form and include the following: particle bed reactor (PBR) core cross section; PBR bleed cycle; fuel and moderator flow paths; PBR modeling requirements; characteristics of PBR and nuclear thermal propulsion (NTP) modeling; challenges for PBR and NTP modeling; thermal hydraulic computer codes; capabilities for PBR/reactor application; thermal/hydralic codes; limitations; physical correlations; comparison of predicted friction factor and experimental data; frit pressure drop testing; cold frit mask factor; decay heat flow rate; startup transient simulation; and philosophy of systems modeling.

Mussel beds are biological power stations on intertidal flats

Science.gov (United States)

Engel, Friederike G.; Alegria, Javier; Andriana, Rosyta; Donadi, Serena; Gusmao, Joao B.; van Leeuwe, Maria A.; Matthiessen, Birte; Eriksson, Britas Klemens

2017-05-01

Intertidal flats are highly productive areas that support large numbers of invertebrates, fish, and birds. Benthic diatoms are essential for the function of tidal flats. They fuel the benthic food web by forming a thin photosynthesizing compartment in the top-layer of the sediment that stretches over the vast sediment flats during low tide. However, the abundance and function of the diatom film is not homogenously distributed. Recently, we have realized the importance of bivalve reefs for structuring intertidal ecosystems; by creating structures on the intertidal flats they provide habitat, reduce hydrodynamic stress and modify the surrounding sediment conditions, which promote the abundance of associated organisms. Accordingly, field studies show that high chlorophyll a concentration in the sediment co-vary with the presence of mussel beds. Here we present conclusive evidence by a manipulative experiment that mussels increase the local biomass of benthic microalgae; and relate this to increasing biomass of microalgae as well as productivity of the biofilm across a nearby mussel bed. Our results show that the ecosystem engineering properties of mussel beds transform them into hot spots for primary production on tidal flats, highlighting the importance of biological control of sedimentary systems.

Status of the fluidized bed unit

International Nuclear Information System (INIS)

Williams, P.M.; Wade, J.F.

1994-01-01

Rocky Flats has a serious mixed waste problem. No technology or company has a license and available facilities to remedy this dilemma. One solution under study is to use a catalytic fluidized bed unit to destroy the combustible portion of the mixed waste. The fluidized bed thermal treatment program at Rocky Flats is building on knowledge gained over twenty years of successful development activity. The FBU has numerous technical advantages over other thermal technologies to treat Rocky Flats' mixed waste, the largest being the lower temperature (700 degrees C versus 1000 degrees C) which reduces acid corrosion and mechanical failures and obviates the need for ceramic lining. Successful demonstrations have taken place on bench, pilot, and full-scale tests using radioactive mixed wastes. The program is approaching implementation and licensing of a production-scale fluidized bed system for the safe treatment of mixed waste. The measure for success on this project is the ability to work closely with the community to jointly solve problems and respond to concerns of mixed waste treatment at Rocky Flats

Flue Gas Emissions from Fluidized Bed Combustion

NARCIS (Netherlands)

Bramer, E.A.; Valk, M.

1995-01-01

During the past decades fluidized bed coal combustion was developed as a technology for burning coal in an effective way meeting the standards for pollution control. During the earlier years of research on fluidized bed combustion, the potential for limiting the S02 emission by adding limestone to

Nonhomologous Synapsis and Reduced Crossing over in a Heterozygous Paracentric Inversion in Saccharomyces Cerevisiae

Science.gov (United States)

Dresser, M. E.; Ewing, D. J.; Harwell, S. N.; Coody, D.; Conrad, M. N.

1994-01-01

Homologous chromosome synapsis (``homosynapsis'') and crossing over are well-conserved aspects of meiotic chromosome behavior. The long-standing assumption that these two processes are causally related has been challenged recently by observations in Saccharomyces cerevisiae of significant levels of crossing over (1) between small sequences at nonhomologous locations and (2) in mutants where synapsis is abnormal or absent. In order to avoid problems of local sequence effects and of mutation pleiotropy, we have perturbed synapsis by making a set of isogenic strains that are heterozygous and homozygous for a large chromosomal paracentric inversion covering a well marked genetic interval and then measured recombination. We find that reciprocal recombination in the marked interval in heterozygotes is reduced variably across the interval, on average to ~55% of that in the homozygotes, and that positive interference still modulates crossing over. Cytologically, stable synapsis across the interval is apparently heterologous rather than homologous, consistent with the interpretation that stable homosynapsis is required to initiate or consummate a large fraction of the crossing over observed in wild-type strains. When crossing over does occur in heterozygotes, dicentric and acentric chromosomes are formed and can be visualized and quantitated on blots though not demonstrated in viable spores. We find that there is no loss of dicentric chromosomes during the two meiotic divisions and that the acentric chromosome is recovered at only 1/3 to 1/2 of the expected level. PMID:7851761

Media arrangement impacts cell growth in anaerobic fixed-bed reactors treating sugarcane vinasse: Structured vs. randomic biomass immobilization.

Science.gov (United States)

de Aquino, Samuel; Fuess, Lucas Tadeu; Pires, Eduardo Cleto

2017-07-01

This study reports on the application of an innovative structured-bed reactor (FVR) as an alternative to conventional packed-bed reactors (PBRs) to treat high-strength solid-rich wastewaters. Using the FVR prevents solids from accumulating within the fixed-bed, while maintaining the advantages of the biomass immobilization. The long-term operation (330days) of a FVR and a PBR applied to sugarcane vinasse under increasing organic loads (2.4-18.0kgCODm -3 day -1 ) was assessed, focusing on the impacts of the different media arrangements over the production and retention of biomass. Much higher organic matter degradation rates, as well as long-term operational stability and high conversion efficiencies (>80%) confirmed that the FVR performed better than the PBR. Despite the equivalent operating conditions, the biomass growth yield was different in both reactors, i.e., 0.095gVSSg -1 COD (FVR) and 0.066gVSSg -1 COD (PBR), indicating a clear control of the media arrangement over the biomass production in fixed-bed reactors. Copyright © 2017 Elsevier Ltd. All rights reserved.

Toxicities of Selected Essential Oils, Silicone Oils, and Paraffin Oil against the Common Bed Bug (Hemiptera: Cimicidae).

Science.gov (United States)

Zha, Chen; Wang, Changlu; Li, Andrew

2018-02-09

The common bed bug [Cimex lectularius L. (Hemiptera: Cimicidae)] and tropical bed bug [Cimex hemipterus F. (Hemiptera: Cimicidae)] resurged in the United States and many other countries over the past decades. The need for safe and effective bed bug control products propelled the development of numerous 'green insecticides', mostly with essential oils listed as active ingredients. Various inorganic and organic oils also were used for bed bug management. However, there are no published studies on their toxicities against bed bugs. In this study, we screened 18 essential oils, three silicone oils, and paraffin oil (C5-20 paraffins) for their toxicities against bed bugs. All the oils exhibited insecticidal activity in topical assays. Their toxicities varied significantly; all of the evaluated essential oils were less effective than silicone oils and paraffin oil. The LD50 values of the most effective essential oil (blood orange), paraffin oil, and the most effective silicone oil (dodecamethylpentasiloxane) are 0.184 ± 0.018, 0.069 ± 0.012, and 0.036 ± 0.005 mg per bug, respectively. Direct spray of 1% water solution of 3-[hydroxy (polyethyleneoxy) propyl] heptamethyltrisiloxane, the only silicone oil that mixes well with water, resulted in 92% bed bug mortality after 1 d. Results of this study indicate silicone oils and paraffin oil have the potential to be used as safer alternative bed bug control materials. © The Author(s) 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

On-line temperature control of fluidized bed incinerator using fuzzy algorithm; Fuzzu seigyo donyu ni yoru ryudosogata shokyakuro unten no jidoka

Energy Technology Data Exchange (ETDEWEB)

Okayasu, S.; Kuratani, T.; Imai, H. [Ajinomoto Co. Inc., Tokyo (Japan)

1995-03-15

Automatic control of incinerators for their stable operation has been desired for the preservation of the environment in the factory. An on-line fuzzy control system has been successfully introduced for temperature control of the fluidized bed of incinerator for industrial wastes. In this case, manual control can be applied to the plant instead of a PID control system, because of the complexity of the waste materials and the large delay in detection of the temperature change in the fluidized bed sand. On the basis of analyzing the dynamic performance of the process and the know-how of skilled operators, membership functions and fuzzy control rules are selected, then determined carefully for the system. Introduction of the system resulted in almost the same performance as manual control. Subsequently the operators are freed from manual operation in the control room for an hour. 6 refs., 5 figs., 4 tabs.

Use of bed nets and factors that influence bed net use among Jinuo Ethnic Minority in southern China.

Science.gov (United States)

Xu, Jian-wei; Liao, Yuan-mei; Liu, Hui; Nie, Ren-hua; Havumaki, Joshua

2014-01-01

Insecticide-treated nets (ITNs) are an integral part of vector control recommendations for malaria elimination in China. This study investigated the extent to which bed nets were used and which factors influence bed net use among Jinuo Ethnic Minority in China-Myanmar-Laos border areas. This study combined a quantitative household questionnaire survey and qualitative semi-structured in-depth interviews (SDI). Questionnaires were administered to 352 heads of households. SDIs were given to 20 key informants. The bed net to person ratio was 1∶2.1 (i.e., nearly one net for every two people), however only 169 (48.0%) households owned at least one net and 623 (47.2%) residents slept under bed nets the prior night. The percentages of residents who regularly slept under nets (RSUN) and slept under nets the prior night (SUNPN) were similar (48.0% vs. 47.2%, P>0.05), however the percentage correct use of nets (CUN) was significantly lower (34.5%, Pcash income per person (ACIP) was an independent factor that influenced bed net use (PHigh bed net availability does not necessarily mean higher coverage or bed net use. Household income, house type and knowledge of the ability of bed nets to prevent malaria are all independent factors that influence bed net use among Jinuo Ethnic Minority.

International Space Station Sustaining Engineering: A Ground-Based Test Bed for Evaluating Integrated Environmental Control and Life Support System and Internal Thermal Control System Flight Performance

Science.gov (United States)

Ray, Charles D.; Perry, Jay L.; Callahan, David M.

2000-01-01

As the International Space Station's (ISS) various habitable modules are placed in service on orbit, the need to provide for sustaining engineering becomes increasingly important to ensure the proper function of critical onboard systems. Chief among these are the Environmental Control and Life Support System (ECLSS) and the Internal Thermal Control System (ITCS). Without either, life onboard the ISS would prove difficult or nearly impossible. For this reason, a ground-based ECLSS/ITCS hardware performance simulation capability has been developed at NASA's Marshall Space Flight Center. The ECLSS/ITCS Sustaining Engineering Test Bed will be used to assist the ISS Program in resolving hardware anomalies and performing periodic performance assessments. The ISS flight configuration being simulated by the test bed is described as well as ongoing activities related to its preparation for supporting ISS Mission 5A. Growth options for the test facility are presented whereby the current facility may be upgraded to enhance its capability for supporting future station operation well beyond Mission 5A. Test bed capabilities for demonstrating technology improvements of ECLSS hardware are also described.

Characterization of biofilm in 200W fluidized bed reactors

Energy Technology Data Exchange (ETDEWEB)

Lee, Michelle H. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Saurey, Sabrina D. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Lee, Brady D. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Parker, Kent E. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Eisenhauer, Emalee E. R. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Cordova, Elsa A. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Golovich, Elizabeth C. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States)

2014-09-29

Contaminated groundwater beneath the 200 West Area at the Hanford Site in Southeast Washington is currently being treated using a pump and treat system to remove organics, inorganics, radionuclides, and metals. A granular activated carbon-based fluidized bed reactor (FBR) has been added to remove nitrate, hexavalent chromium and carbon tetrachloride. Initial analytical results indicated the microorganisms effectively reduced many of the contaminants to less than cleanup levels. However shortly thereafter operational upsets of the FBR include carbon carry over, over production of microbial extracellular polymeric substance (biofilm) materials, and over production of hydrogen sulfide. As a result detailed investigations were undertaken to understand the functional diversity and activity of the microbial community present in the FBR over time. Molecular analyses including terminal restriction fragment length polymorphism analysis, quantitative polymerase chain reaction and fluorescent in situ hybridization analyses were performed on the microbial community extracted from the biofilm within the bed and from the inoculum, to determine functional dynamics of the FBR bed over time and following operational changes. Findings from these analyses indicated: 1) the microbial community within the bed was completely different than community used for inoculation, and was likely from the groundwater; 2) analyses early in the testing showed an FBR community dominated by a few Curvibacter and Flavobacterium species; 3) the final sample taken indicated that the microbial community in the FBR bed had become more diverse; and 4) qPCR analyses indicated that bacteria involved in nitrogen cycling, including denitrifiers and anaerobic ammonia oxidizing bacteria, were dominant in the bed. These results indicate that molecular tools can be powerful for determining functional diversity within FBR type reactors. Coupled with micronutrient, influent and effluent chemistry

Infant's bed climate and bedding in the Japanese home.

Science.gov (United States)

Nakamura Ikeda, Rie; Fukai, Kiyoko; Okamoto Mizuno, Kazue

2012-06-01

to assess the bed climate of infants in their homes in Japan. descriptive, exploratory, non-experimental research design. the data were collected at the participants' homes under normal circumstances. nineteen healthy infants between the ages of two and five months. Their mothers, who joined a parenting class organised by a maternity clinic in Okayama, Japan, consented to participate in this study. we visited the infants' homes and interviewed their mothers concerning the types and use of bedding. The temperature and relative humidity of the bed climate at the back and foot of the bedding, and in the room were measured every minute for four consecutive days. Differences among the bed climates measured during three seasons (spring, summer, and autumn) were assessed by one-way analysis of variance. The bed temperature was higher for infants than for adults. No significant difference in temperature was noted among the three seasons. The bed temperature was about 36.0°C when waterproof sheets and futon mattresses for children or adult were used. The average relative humidity of the bed climate at the back was highest in summer, followed by that in spring and autumn; the differences were significant. The use of waterproof sheets and futon mattresses for children in summer increased the relative humidity to 80% or more. The use of infant beds, sunoko drainboards, and cotton futon mattresses in summer was effective in reducing the bed humidity. these results suggest that nurse-midwives should advise the parents on comfortable bed climates for their infants, as well as how to select and use bedding for them. Copyright © 2010 Elsevier Ltd. All rights reserved.

Plated nickel wire mesh makes superior catalyst bed

Science.gov (United States)

Sill, M.

1965-01-01

Porous nickel mesh screen catalyst bed produces gas evolution in hydrogen peroxide thrust chambers used for attitude control of space vehicles. The nickel wire mesh disks in the catalyst bed are plated in rugose form with a silver-gold coating.

Biomechanics-based active control of bedding support properties and its influence on sleep.

Science.gov (United States)

Van Deun, D; Verhaert, V; Willemen, T; Wuyts, J; Verbraecken, J; Exadaktylos, V; Haex, B; Vander Sloten, J

2012-01-01

Proper body support plays an import role in the recuperation of our body during sleep. Therefore, this study uses an automatically adapting bedding system that optimises spinal alignment throughout the night by altering the stiffness of eight comfort zones. The aim is to investigate the influence of such a dynamic sleep environment on objective and subjective sleep parameters. The bedding system contains 165 sensors that measure mattress indentation. It also includes eight actuators that control the comfort zones. Based on the measured mattress indentation, body movements and posture changes are detected. Control of spinal alignment is established by fitting personalized human models in the measured indentation. A total of 11 normal sleepers participated in this study. Sleep experiments were performed in a sleep laboratory where subjects slept three nights: a first night for adaptation, a reference night and an active support night (in counterbalanced order). Polysomnographic measurements were recorded during the nights, combined with questionnaires aiming at assessing subjective information. Subjective information on sleep quality, daytime quality and perceived number of awakenings shows significant improvements during the active support (ACS) night. Objective results showed a trend towards increased slow wave sleep. On the other hand, it was noticed that % N1-sleep was significantly increased during ACS night, while % N2-sleep was significantly decreased. No prolonged N1 periods were found during or immediately after steering.

Transient core-debris bed heat-removal experiments and analysis

International Nuclear Information System (INIS)

Ginsberg, T.; Klein, J.; Klages, J.; Schwarz, C.E.; Chen, J.C.

1982-08-01

An experimental investigation is reported of the thermal interaction between superheated core debris and water during postulated light-water reactor degraded core accidents. Data are presented for the heat transfer characteristics of packed beds of 3 mm spheres which are cooled by overlying pools of water. Results of transient bed temperature and steam flow rate measurements are presented for bed heights in the range 218 mm-433 mm and initial particle bed temperatures between 530K and 972K. Results display a two-part sequential quench process. Initial frontal cooling leaves pockets or channels of unquenched spheres. Data suggest that heat transfer process is limited by a mechanism of countercurrent two-phase flow. An analytical model which combines a bed energy equation with either a quasisteady version of the Lipinski debris bed model or a critical heat flux model reasonably well predicts the characteristic features of the bed quench process. Implications with respect to reactor safety are discussed

SYNROC production using a fluid bed calciner

International Nuclear Information System (INIS)

Ackerman, F.J.; Grens, J.Z.; Ryerson, F.J.; Hoenig, C.L.; Bazan, F.; Campbell, J.H.

1982-01-01

SYNROC is a titanate-based ceramic developed for immobilization of high-level nuclear reactor wastes in solid form. Fluid-bed SYNROC production permits slurry drying, calcining and redox to be carried out in a single unit. We present results of studies from two fluid beds; the Idaho Exxon internally-heated unit and the externally-heated unit constructed at Lawrence Livermore National laboratory. Bed operation over a range of temperature, feed rate, fluidizing rate and redox conditions indicate that high density, uniform particle-size SYNROC powders are produced which facilitate the densification step and give HUP parts with dense, well-developed phases and good leaching characteristics. 3 figures, 3 tables

Experimental study of improvement on combustion control of fluidized bed combustion chamber; Ryudosho shokyakuro no nenshosei no kaizen ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Izumiya, T.; Baba, K.; Koshida, H.; Uetani, J.; Furuta, M.

1998-10-29

Nippon Steel Corporation has carried out an experimental study using the Yawata waste incinerator plant in order to improve combustion control of a fluidized bed combustion chamber. For controlling the forming of dioxin, combustion control is very important in addition to conventional methods. In this paper, we report two studies about improvements on combustion control. In the first study, we verified improvement on combustion control by modifying gas flow at the freeboard. The operational results of the experiments were studied using the numerical model of the combustion chamber. The modification of gas flow at freeboard was confirmed to be effective to obtain a compact design of fluidized bed combustion chamber for municipal waste. In the second, study we improved combustion control for sewage combustion with municipal waste. In burning municipal waste and sewage, it is especially required to take combustion control into careful consideration. In this experiment, we developed a new device for supplying sewage for the appropriate controlling combustion, and verified its effectiveness to combustion control and an effective reduction of dioxin. (author)

Slow sedimentary processes on-a-chip: experiments on porous flow effects on granular bed creep

Science.gov (United States)

Houssais, M.; Maldarelli, C.; Shattuck, M.; Morris, J. F.

2017-12-01

Steep soils dynamics is hard to catch. they exhibit very slow granular creep most of the time, and sometimes, mostly under or after rain, turn into a landslide, a very fast avalanche flow.The conditions of transition from soil creep to avalanching remains a lot non-understood, and Safe Factor law (empirical criteria, function of rain intensity and duration). On another side, in marine fast deposition environments, compaction drives vertical porous flow, which makes bed shear resistance change, and form over time bed size patterns (pipes, dishes) or mechanical heterogeneities.Capturing how the slow creep dynamics depends on the porous flow would allow for much more accurate landscape evolution modeling.We present here preliminary results of an experimental investigation of one the major triggering condition for soils destabilization: rain infiltration, and more generally porous flow through a tilted granular bed. In a quasi-2D microfluidics channel, a flat sediment bed made of spherical particles is prepared, in fully submerged condition. It is thereafter tilted (at slope under critical slope of avalanching) and simultaneously put under vertical weak porous flow (well under the critical flow of liquefaction regarding positive pressure gradients). The two control parameters are varied, and local particles concentration and motion are measured. Interestingly, although staying in the sub-critical creeping regime, we observe an acceleration of the bed deformation downward, as the porous flow and the bed slope are increased, until the criteria for avalanching is reached. Those results appear to present similitudes with the case of tilted dry sediment bed under controlled vibrations. Consequently it opens the discussion about a potential universal model of landslides triggering due to frequent seismological and rainstorm events.

Gradient Compression Stockings may Prevent Recovery after Bed Rest Deconditioning

Science.gov (United States)

Stenger, Michael B.; Lee, Stuart M.; Westby, Christian M.; Willig, Michael C.; Platts, Steven H.

2011-01-01

Introduction: Astronauts continue to wear a compression garment during and immediately after landing to prevent orthostatic intolerance (OI). We recently developed a custom-fitted, 3-piece garment that consists of thigh-high stockings with biker-style shorts that provides continuous, gradient compression: 55 mmHg at the ankle that decreases to approximately 20 mmHg at the top of the leg and 15 mmHg over the abdomen. This garment has been shown to be effective in preventing symptoms of OI during a short stand test after Space Shuttle missions, but symptoms may persist for several days after a long-duration mission in some astronauts. The purpose of this study was to confirm the effectiveness of wearing these elastic, gradient compression garments during orthostatic testing after 2 weeks of 6 degree head-down tilt bed rest as a model of spaceflight and to determine whether they would impact recovery after bed rest. Methods: Eight (5 treatment, 3 control) of 16 subjects have completed this study to-date. All subjects wore the 3-piece garment from waking until tilt testing (3 h) as a simulation of the timeline for astronauts on landing day (BR+0). Control subjects removed the garment after the tilt test. Treatment subjects wore the garment for the remainder of the day and wore lower compression thigh-high only garments on the day after bed rest (BR+1). Blood pressure, heart rate, and stroke volume responses to a 15-min 80 degree head-up tilt test were determined before 2 weeks of 6 degree head-down tilt, and on BR+0 and BR+1. Plasma volume (PV) was measured before each of these test sessions. Data are mean SE. Results: Compression garments prevented signs of OI on BR+0; all subjects in both groups completed the full 15-min test. Heart rate responses to tilt were lower on BR+0 than all other test days. Control subjects demonstrated a marginal PV decrease after bed rest, but showed typical recovery the day after bed rest (BR+0: 2.32 plus or minus 0.15 L to BR+1: 2

Interaction between bedding and sleeping position in the sudden infant death syndrome: a population based case-control study.

Science.gov (United States)

Fleming, P J; Gilbert, R; Azaz, Y; Berry, P J; Rudd, P T; Stewart, A; Hall, E

1990-01-01

OBJECTIVE--To determine the relation between sleeping position and quantity of bedding and the risk of sudden unexpected infant death. DESIGN--A study of all infants dying suddenly and unexpectedly and of two controls matched for age and date with each index case. The parents of control infants were interviewed within 72 hours of the index infant's death. Information was collected on bedding, sleeping position, heating, and recent signs of illness for index and control infants. SETTING--A defined geographical area comprising most of the county of Avon and part of Somerset. SUBJECTS--72 Infants who had died suddenly and unexpectedly (of whom 67 had died from the sudden infant death syndrome) and 144 control infants. RESULTS--Compared with the control infants the infants who had died from the sudden infant death syndrome were more likely to have been sleeping prone (relative risk 8.8; 95% confidence interval 7.0 to 11.0; p less than 0.001), to have been more heavily wrapped (relative risk 1.14 per tog above 8 tog; 1.03 to 1.28; p less than 0.05), and to have had the heating on all night (relative risk 2.7; 1.4 to 5.2; p less than 0.01). These differences were less pronounced in the younger infants (less than 70 days) than the older ones. The risk of sudden unexpected death among infants older than 70 days, nursed prone, and with clothing and bedding of total thermal resistance greater than 10 tog was increased by factors of 15.1 (2.6 to 89.6) and 25.2 (3.7 to 169.0) respectively compared with the risk in infants of the same age nursed supine or on their side and under less than 6 tog of bedding. CONCLUSIONS--Overheating and the prone position are independently associated with an increased risk of sudden unexpected infant death, particularly in infants aged more than 70 days. Educating parents about appropriate thermal care and sleeping position of infants may help to reduce the incidence of the sudden infant death syndrome. PMID:2390588

Nurse-physician teamwork in the emergency department: impact on perceptions of job environment, autonomy, and control over practice.

Science.gov (United States)

Ajeigbe, David O; McNeese-Smith, Donna; Leach, Linda Searle; Phillips, Linda R

2013-03-01

Teamwork is essential to safety. Few studies focus on teamwork between nurses and physicians in emergency departments (EDs). The aim of this study was to examine differences between staff in the interventional group EDs (IGEDs) and control group EDs (CGEDs) on perception of job environment, autonomy, and control over practice. This was a comparative cross-sectional study of the impact of teamwork on perceptions of job environment, autonomy, and control over practice by registered nurses and physicians (MDs) in EDs. Staff in the IGEDs showed significant differences compared with staff who worked in the CGEDs on staff perception of job environment, autonomy, and control over practice. Active teamwork practice was associated with increased perceptions of a positive job environment, autonomy, and control over practice of both nurses and physicians.

Effects of Subsensory Noise and Fatigue on Knee Landing and Cross-over Cutting Biomechanics in Male Athletes.

Science.gov (United States)

Qu, Xingda; Jiang, Jianxin; Hu, Xinyao

2018-06-01

The objective of this study was to examine the effects of subsensory noise and fatigue on knee biomechanics during the athletic task of landing followed by cross-over cutting. A total of 32 healthy male athletes participated in the study. They were evenly divided into 2 groups: no fatigue group and fatigue group. Fatigue was induced to the lower extremity by a repetitive squatting exercise in the fatigue group. Subsensory noise was generated by linear miniature vibrators bilaterally placed around the knee joints. During data collection, the participants were instructed to perform landing followed by cross-over cutting in both the subsensory on and off conditions. Dependent variables were selected to assess knee biomechanics in the phases of landing and cross-over cutting, separately. Results showed that fatigue resulted in larger knee flexion during landing and larger knee internal rotation during cross-over cutting. Subsensory noise was found to reduce knee rotation impulse during cross-over cutting. These findings suggest that cross-over cutting is more dangerous than landing in the fatigue condition, and subsensory noise may lead to changes in knee biomechanics consistent with reduced risk of anterior cruciate ligament injuries, but the changes may be task-specific.

Controlling groundwater over abstraction

NARCIS (Netherlands)

Naber, Al Majd; Molle, Francois

2017-01-01

The control of groundwater over abstraction is a vexing problem worldwide. Jordan is one of the countries facing severe water scarcity which has implemented a wide range of measures and policies over the past 20 years. While the gap between formal legal and policy frameworks and local practices on

An assessment of biological processes close to the sea bed in a slope region and its significance to the assessment of sea bed disposal of radioactive waste

International Nuclear Information System (INIS)

Hargreaves, P.M.; Ellis, C.J.; Angel, M.V.

1984-01-01

Vertical profiles of planktonic and micronektonic biomass observed close to the sea bed along a transect running up the continental slope on the southern flank of the Porcupine Seabight (to the southwest of Ireland) showed that a doubling in biomass concentration occurs from 100 to 10m above the sea bed. Comparison with biomass concentrations at two deep water stations, one in the Seabight and the other in the Rockall Trough, showed that there was a consistent increase in standing crop close to the sea bed over the slope. Supplementary data were collected on the northern flank of the Seabight. Analysis of both taxonomic groups and individual species showed that some taxa were more abundant near the sea floor and extended their vertical ranges to greater depths over the slope than over deep water, other taxa were unaffected. The implications to the problem of assessing the safety of sea bed disposal of high level radioactive waste are summarised. (author)

A randomized, controlled cross-over trial of dermally-applied lavender (Lavandula angustifolia) oil as a treatment of agitated behaviour in dementia.

Science.gov (United States)

O'Connor, Daniel W; Eppingstall, Barbara; Taffe, John; van der Ploeg, Eva S

2013-11-13

Lavender essential oil shows evidence of sedative properties in neurophysiological and animal studies but clinical trials of its effectiveness as a treatment of agitation in people with dementia have shown mixed results. Study methods have varied widely, however, making comparisons hazardous. To help remedy previous methodological shortcomings, we delivered high grade lavender oil in specified amounts to nursing home residents whose agitated behaviours were recorded objectively. 64 nursing home residents with frequent physically agitated behaviours were entered into a randomized, single-blind cross-over trial of dermally-applied, neurophysiologically active, high purity 30% lavender oil versus an inactive control oil. A blinded observer counted the presence or absence of target behaviours and rated participants' predominant affect during each minute for 30 minutes prior to exposure and for 60 minutes afterwards. Lavender oil did not prove superior to the control oil in reducing the frequency of physically agitated behaviours or in improving participants' affect. Studies of essential oils are constrained by their variable formulations and uncertain pharmacokinetics and so optimal dosing and delivery regimens remain speculative. Notwithstanding this, topically delivered, high strength, pure lavender oil had no discernible effect on affect and behaviour in a well-defined clinical sample. Australian and New Zealand Clinical Trials Registry (ACTRN 12609000569202).

Development and Evaluation of a Wide-Bed Former for Vegetable Cultivation in Controlled Tractor Traffic

Science.gov (United States)

Dixit, Anoop; Khurana, Rohinish; Verma, Aseem; Singh, Arshdeep; Manes, G. S.

2018-05-01

India is the second largest producer of vegetables in the world. For vegetable cultivation, a good seed bed preparation is an important task which involves 6-10 different operations. To tackle the issue of multiple operations, a prototype of tractor operated wide bed former was developed and evaluated. The machine comprises of a rotary tiller and a bed forming setup. It forms bed of 1000 mm top width which is suitable as per the track width of an average sized tractor in India. The height of the beds formed is 130 mm whereas the top and bottom width of channel formed on both sides of the bed is 330 and 40 mm respectively at soil moisture content of 12.5-16% (db). The forward speed of 2.75 km/h was observed to be suitable for proper bed formation. The average fuel consumption of the machine was 5.9 l/h. The average bulk density of soil before and after the bed formation was 1.46 and 1.63 g/cc respectively. Field capacity of the machine was found to be 0.31 ha/h. The machine resulted in 93.8% labour saving and 80.4% saving in cost of bed preparation as compared to conventional farmer practice. Overall performance of wide-bed former was found to be satisfactory.

Evaluation of Green-LiDAR Data for Mapping Extent, Density and Height of Aquatic Reed Beds at Lake Chiemsee, Bavaria—Germany

Directory of Open Access Journals (Sweden)

Nicolás Corti Meneses

2017-12-01

Full Text Available Aquatic reed is an important indicator for the ecological assessment of freshwater lakes. Monitoring is essential to document its expansion or deterioration and decline. The applicability of Green-LiDAR data for the status assessment of aquatic reed beds of Bavarian freshwater lakes was investigated. The study focused on mapping diagnostic structural parameters of aquatic reed beds by exploring 3D data provided by the Green-LiDAR system. Field observations were conducted over 14 different areas of interest along 152 cross-sections. The data indicated the morphologic and phenologic traits of aquatic reed, which were used for validation purposes. For the automatic classification of aquatic reed bed spatial extent, density and height, a rule-based algorithm was developed. LiDAR data allowed for the delimitating of the aquatic reed frontline, as well as shoreline, and therefore an accurate quantification of extents (Hausdorff distance = 5.74 m and RMSE of cross-sections length 0.69 m. The overall accuracy measured for aquatic reed bed density compared to the simultaneously recorded aerial imagery was 96% with a Kappa coefficient of 0.91 and 72% (Kappa = 0.5 compared to field measurements. Digital Surface Models (DSM, calculated from point clouds, similarly showed a high level of agreement in derived heights of flat surfaces (RMSE = 0.1 m and showed an adequate agreement of aquatic reed heights with evenly distributed errors (RMSE = 0.8 m. Compared to field measurements, aerial laser scanning delivered valuable information with no disturbance of the habitat. Analysing data with our classification procedure improved the efficiency, reproducibility, and accuracy of the quantification and monitoring of aquatic reed beds.

Improving Emergency Department flow through optimized bed utilization.

Science.gov (United States)

Chartier, Lucas Brien; Simoes, Licinia; Kuipers, Meredith; McGovern, Barb

2016-01-01

Over the last decade, patient volumes in the emergency department (ED) have grown disproportionately compared to the increase in staffing and resources at the Toronto Western Hospital, an academic tertiary care centre in Toronto, Canada. The resultant congestion has spilled over to the ED waiting room, where medically undifferentiated and potentially unstable patients must wait until a bed becomes available. The aim of this quality improvement project was to decrease the 90th percentile of wait time between triage and bed assignment (time-to-bed) by half, from 120 to 60 minutes, for our highest acuity patients. We engaged key stakeholders to identify barriers and potential strategies to achieve optimal flow of patients into the ED. We first identified multiple flow-interrupting challenges, including operational bottlenecks and cultural issues. We then generated change ideas to address two main underlying causes of ED congestion: unnecessary patient utilization of ED beds and communication breakdown causing bed turnaround delays. We subsequently performed seven tests of change through sequential plan-do-study-act (PDSA) cycles. The most significant gains were made by improving communication strategies: small gains were achieved through the optimization of in-house digital information management systems, while significant improvements were achieved through the implementation of a low-tech direct contact mechanism (a two-way radio or walkie-talkie). In the post-intervention phase, time-to-bed for the 90th percentile of high-acuity patients decreased from 120 minutes to 66 minutes, with special cause variation showing a significant shift in the weekly measurements.

First measurement of the tt[over ] differential cross section dsigma/dM_{tt[over ]} in pp[over ] collisions at sqrt[s]=1.96 TeV.

Science.gov (United States)

Aaltonen, T; Adelman, J; Akimoto, T; Alvarez González, B; Amerio, S; Amidei, D; Anastassov, A; Annovi, A; Antos, J; Apollinari, G; Apresyan, A; Arisawa, T; Artikov, A; Ashmanskas, W; Attal, A; Aurisano, A; Azfar, F; Azzurri, P; Badgett, W; Barbaro-Galtieri, A; Barnes, V E; Barnett, B A; Bartsch, V; Bauer, G; Beauchemin, P-H; Bedeschi, F; Beecher, D; Behari, S; Bellettini, G; Bellinger, J; Benjamin, D; Beretvas, A; Beringer, J; Bhatti, A; Binkley, M; Bisello, D; Bizjak, I; Blair, R E; Blocker, C; Blumenfeld, B; Bocci, A; Bodek, A; Boisvert, V; Bolla, G; Bortoletto, D; Boudreau, J; Boveia, A; Brau, B; Bridgeman, A; Brigliadori, L; Bromberg, C; Brubaker, E; Budagov, J; Budd, H S; Budd, S; Burke, S; Burkett, K; Busetto, G; Bussey, P; Buzatu, A; Byrum, K L; Cabrera, S; Calancha, C; Campanelli, M; Campbell, M; Canelli, F; Canepa, A; Carls, B; Carlsmith, D; Carosi, R; Carrillo, S; Carron, S; Casal, B; Casarsa, M; Castro, A; Catastini, P; Cauz, D; Cavaliere, V; Cavalli-Sforza, M; Cerri, A; Cerrito, L; Chang, S H; Chen, Y C; Chertok, M; Chiarelli, G; Chlachidze, G; Chlebana, F; Cho, K; Chokheli, D; Chou, J P; Choudalakis, G; Chuang, S H; Chung, K; Chung, W H; Chung, Y S; Chwalek, T; Ciobanu, C I; Ciocci, M A; Clark, A; Clark, D; Compostella, G; Convery, M E; Conway, J; Cordelli, M; Cortiana, G; Cox, C A; Cox, D J; Crescioli, F; Cuenca Almenar, C; Cuevas, J; Culbertson, R; Cully, J C; Dagenhart, D; Datta, M; Davies, T; de Barbaro, P; De Cecco, S; Deisher, A; De Lorenzo, G; Dell'orso, M; Deluca, C; Demortier, L; Deng, J; Deninno, M; Derwent, P F; di Giovanni, G P; Dionisi, C; Di Ruzza, B; Dittmann, J R; D'Onofrio, M; Donati, S; Dong, P; Donini, J; Dorigo, T; Dube, S; Efron, J; Elagin, A; Erbacher, R; Errede, D; Errede, S; Eusebi, R; Fang, H C; Farrington, S; Fedorko, W T; Feild, R G; Feindt, M; Fernandez, J P; Ferrazza, C; Field, R; Flanagan, G; Forrest, R; Frank, M J; Franklin, M; Freeman, J C; Furic, I; Gallinaro, M; Galyardt, J; Garberson, F; Garcia, J E; Garfinkel, A F; Genser, K; Gerberich, H; Gerdes, D; Gessler, A; Giagu, S; Giakoumopoulou, V; Giannetti, P; Gibson, K; Gimmell, J L; Ginsburg, C M; Giokaris, N; Giordani, M; Giromini, P; Giunta, M; Giurgiu, G; Glagolev, V; Glenzinski, D; Gold, M; Goldschmidt, N; Golossanov, A; Gomez, G; Gomez-Ceballos, G; Goncharov, M; González, O; Gorelov, I; Goshaw, A T; Goulianos, K; Gresele, A; Grinstein, S; Grosso-Pilcher, C; Grundler, U; Guimaraes da Costa, J; Gunay-Unalan, Z; Haber, C; Hahn, K; Hahn, S R; Halkiadakis, E; Han, B-Y; Han, J Y; Happacher, F; Hara, K; Hare, D; Hare, M; Harper, S; Harr, R F; Harris, R M; Hartz, M; Hatakeyama, K; Hays, C; Heck, M; Heijboer, A; Heinrich, J; Henderson, C; Herndon, M; Heuser, J; Hewamanage, S; Hidas, D; Hill, C S; Hirschbuehl, D; Hocker, A; Hou, S; Houlden, M; Hsu, S-C; Huffman, B T; Hughes, R E; Husemann, U; Hussein, M; Huston, J; Incandela, J; Introzzi, G; Iori, M; Ivanov, A; James, E; Jang, D; Jayatilaka, B; Jeon, E J; Jha, M K; Jindariani, S; Johnson, W; Jones, M; Joo, K K; Jun, S Y; Jung, J E; Junk, T R; Kamon, T; Kar, D; Karchin, P E; Kato, Y; Kephart, R; Keung, J; Khotilovich, V; Kilminster, B; Kim, D H; Kim, H S; Kim, H W; Kim, J E; Kim, M J; Kim, S B; Kim, S H; Kim, Y K; Kimura, N; Kirsch, L; Klimenko, S; Knuteson, B; Ko, B R; Kondo, K; Kong, D J; Konigsberg, J; Korytov, A; Kotwal, A V; Kreps, M; Kroll, J; Krop, D; Krumnack, N; Kruse, M; Krutelyov, V; Kubo, T; Kuhr, T; Kulkarni, N P; Kurata, M; Kwang, S; Laasanen, A T; Lami, S; Lammel, S; Lancaster, M; Lander, R L; Lannon, K; Lath, A; Latino, G; Lazzizzera, I; Lecompte, T; Lee, E; Lee, H S; Lee, S W; Leone, S; Lewis, J D; Lin, C-S; Linacre, J; Lindgren, M; Lipeles, E; Liss, T M; Lister, A; Litvintsev, D O; Liu, C; Liu, T; Lockyer, N S; Loginov, A; Loreti, M; Lovas, L; Lucchesi, D; Luci, C; Lueck, J; Lujan, P; Lukens, P; Lungu, G; Lyons, L; Lys, J; Lysak, R; Macqueen, D; Madrak, R; Maeshima, K; Makhoul, K; Maki, T; Maksimovic, P; Malde, S; Malik, S; Manca, G; Manousakis-Katsikakis, A; Margaroli, F; Marino, C; Marino, C P; Martin, A; Martin, V; Martínez, M; Martínez-Ballarín, R; Maruyama, T; Mastrandrea, P; Masubuchi, T; Mathis, M; Mattson, M E; Mazzanti, P; McFarland, K S; McIntyre, P; McNulty, R; Mehta, A; Mehtala, P; Menzione, A; Merkel, P; Mesropian, C; Miao, T; Miladinovic, N; Miller, R; Mills, C; Milnik, M; Mitra, A; Mitselmakher, G; Miyake, H; Moggi, N; Moon, C S; Moore, R; Morello, M J; Morlock, J; Movilla Fernandez, P; Mülmenstädt, J; Mukherjee, A; Muller, Th; Mumford, R; Murat, P; Mussini, M; Nachtman, J; Nagai, Y; Nagano, A; Naganoma, J; Nakamura, K; Nakano, I; Napier, A; Necula, V; Nett, J; Neu, C; Neubauer, M S; Neubauer, S; Nielsen, J; Nodulman, L; Norman, M; Norniella, O; Nurse, E; Oakes, L; Oh, S H; Oh, Y D; Oksuzian, I; Okusawa, T; Orava, R; Osterberg, K; Pagan Griso, S; Palencia, E; Papadimitriou, V; Papaikonomou, A; Paramonov, A A; Parks, B; Pashapour, S; Patrick, J; Pauletta, G; Paulini, M; Paus, C; Peiffer, T; Pellett, D E; Penzo, A; Phillips, T J; Piacentino, G; Pianori, E; Pinera, L; Pitts, K; Plager, C; Pondrom, L; Poukhov, O; Pounder, N; Prakoshyn, F; Pronko, A; Proudfoot, J; Ptohos, F; Pueschel, E; Punzi, G; Pursley, J; Rademacker, J; Rahaman, A; Ramakrishnan, V; Ranjan, N; Redondo, I; Renton, P; Renz, M; Rescigno, M; Richter, S; Rimondi, F; Ristori, L; Robson, A; Rodrigo, T; Rodriguez, T; Rogers, E; Rolli, S; Roser, R; Rossi, M; Rossin, R; Roy, P; Ruiz, A; Russ, J; Rusu, V; Rutherford, B; Saarikko, H; Safonov, A; Sakumoto, W K; Saltó, O; Santi, L; Sarkar, S; Sartori, L; Sato, K; Savoy-Navarro, A; Schlabach, P; Schmidt, A; Schmidt, E E; Schmidt, M A; Schmidt, M P; Schmitt, M; Schwarz, T; Scodellaro, L; Scribano, A; Scuri, F; Sedov, A; Seidel, S; Seiya, Y; Semenov, A; Sexton-Kennedy, L; Sforza, F; Sfyrla, A; Shalhout, S Z; Shears, T; Shepard, P F; Shimojima, M; Shiraishi, S; Shochet, M; Shon, Y; Shreyber, I; Sidoti, A; Sinervo, P; Sisakyan, A; Slaughter, A J; Slaunwhite, J; Sliwa, K; Smith, J R; Snider, F D; Snihur, R; Soha, A; Somalwar, S; Sorin, V; Spalding, J; Spreitzer, T; Squillacioti, P; Stanitzki, M; St Denis, R; Stelzer, B; Stelzer-Chilton, O; Stentz, D; Strologas, J; Strycker, G L; Stuart, D; Suh, J S; Sukhanov, A; Suslov, I; Suzuki, T; Taffard, A; Takashima, R; Takeuchi, Y; Tanaka, R; Tecchio, M; Teng, P K; Terashi, K; Thom, J; Thompson, A S; Thompson, G A; Thomson, E; Tipton, P; Ttito-Guzmán, P; Tkaczyk, S; Toback, D; Tokar, S; Tollefson, K; Tomura, T; Tonelli, D; Torre, S; Torretta, D; Totaro, P; Tourneur, S; Trovato, M; Tsai, S-Y; Tu, Y; Turini, N; Ukegawa, F; Vallecorsa, S; van Remortel, N; Varganov, A; Vataga, E; Vázquez, F; Velev, G; Vellidis, C; Vidal, M; Vidal, R; Vila, I; Vilar, R; Vine, T; Vogel, M; Volobouev, I; Volpi, G; Wagner, P; Wagner, R G; Wagner, R L; Wagner, W; Wagner-Kuhr, J; Wakisaka, T; Wallny, R; Wang, S M; Warburton, A; Waters, D; Weinberger, M; Weinelt, J; Wester, W C; Whitehouse, B; Whiteson, D; Wicklund, A B; Wicklund, E; Wilbur, S; Williams, G; Williams, H H; Wilson, P; Winer, B L; Wittich, P; Wolbers, S; Wolfe, C; Wright, T; Wu, X; Würthwein, F; Xie, S; Yagil, A; Yamamoto, K; Yamaoka, J; Yang, U K; Yang, Y C; Yao, W M; Yeh, G P; Yoh, J; Yorita, K; Yoshida, T; Yu, G B; Yu, I; Yu, S S; Yun, J C; Zanello, L; Zanetti, A; Zhang, X; Zheng, Y; Zucchelli, S

2009-06-05

We present a measurement of the tt[over ] differential cross section with respect to the tt[over ] invariant mass, dsigma/dM_{tt[over ]}, in pp[over ] collisions at sqrt[s]=1.96 TeV using an integrated luminosity of 2.7 fb;{-1} collected by the CDF II experiment. The tt[over ] invariant mass spectrum is sensitive to a variety of exotic particles decaying into tt[over ] pairs. The result is consistent with the standard model expectation, as modeled by PYTHIA with CTEQ5L parton distribution functions.

Physiological and Functional Alterations after Spaceflight and Bed Rest.

Science.gov (United States)

Mulavara, Ajitkumar P; Peters, Brian T; Miller, Chris A; Kofman, Igor S; Reschke, Millard F; Taylor, Laura C; Lawrence, Emily L; Wood, Scott J; Laurie, Steven S; Lee, Stuart M C; Buxton, Roxanne E; May-Phillips, Tiffany R; Stenger, Michael B; Ploutz-Snyder, Lori L; Ryder, Jeffrey W; Feiveson, Alan H; Bloomberg, Jacob J

2018-04-03

Exposure to microgravity causes alterations in multiple physiological systems, potentially impacting the ability of astronauts to perform critical mission tasks. The goal of this study was to determine the effects of spaceflight on functional task performance and to identify the key physiological factors contributing to their deficits. A test battery comprised of 7 functional tests and 15 physiological measures was used to investigate the sensorimotor, cardiovascular and neuromuscular adaptations to spaceflight. Astronauts were tested before and after 6-month spaceflights. Subjects were also tested before and after 70 days of 6° head-down bed rest, a spaceflight analog, to examine the role of axial body unloading on the spaceflight results. These subjects included Control and Exercise groups to examine the effects of exercise during bed rest. Spaceflight subjects showed the greatest decrement in performance during functional tasks that required the greatest demand for dynamic control of postural equilibrium which was paralleled by similar decrements in sensorimotor tests that assessed postural and dynamic gait control. Other changes included reduced lower limb muscle performance and increased heart rate to maintain blood pressure. Exercise performed during bed rest prevented detrimental change in neuromuscular and cardiovascular function, however, both bed rest groups experienced functional and balance deficits similar to spaceflight subjects. Bed rest data indicates that body support unloading experienced during spaceflight contributes to postflight postural control dysfunction. Further, the bed rest results in the Exercise group of subjects confirm that resistance and aerobic exercises performed during spaceflight can play an integral role in maintaining neuromuscular and cardiovascular function, which can help in reducing decrements in functional performance. These results indicate that a countermeasure to mitigate postflight postural control dysfunction is

Cross-Layer Design Approach for Power Control in Mobile Ad Hoc Networks

Directory of Open Access Journals (Sweden)

A. Sarfaraz Ahmed

2015-03-01

Full Text Available In mobile ad hoc networks, communication among mobile nodes occurs through wireless medium The design of ad hoc network protocol, generally based on a traditional “layered approach”, has been found ineffective to deal with receiving signal strength (RSS-related problems, affecting the physical layer, the network layer and transport layer. This paper proposes a design approach, deviating from the traditional network design, toward enhancing the cross-layer interaction among different layers, namely physical, MAC and network. The Cross-Layer design approach for Power control (CLPC would help to enhance the transmission power by averaging the RSS values and to find an effective route between the source and the destination. This cross-layer design approach was tested by simulation (NS2 simulator and its performance over AODV was found to be better.

The Tulip GT® airway versus the facemask and Guedel airway: a randomised, controlled, cross-over study by Basic Life Support-trained airway providers in anaesthetised patients.

Science.gov (United States)

Shaikh, A; Robinson, P N; Hasan, M

2016-03-01

We performed a randomised, controlled, cross-over study of lung ventilation by Basic Life Support-trained providers using either the Tulip GT® airway or a facemask with a Guedel airway in 60 anaesthetised patients. Successful ventilation was achieved if the provider produced an end-tidal CO2 > 3.5 kPa and a tidal volume > 250 ml in two of the first three breaths, within 60 sec and within two attempts. Fifty-seven (95%) providers achieved successful ventilation using the Tulip GT compared with 35 (58%) using the facemask (p Basic Life Support-trained airway providers. © 2015 The Association of Anaesthetists of Great Britain and Ireland.

Combustion of peanut shells in a cone-shaped bubbling fluidized-bed combustor using alumina as the bed material

International Nuclear Information System (INIS)

Arromdee, Porametr; Kuprianov, Vladimir I.

2012-01-01

Highlights: ► We propose burning of peanut shells in a conical fluidized bed using alumina sand. ► We examine hydrodynamic, combustion and emission characteristics of the reactor. ► High, over 99%, combustion efficiency is achievable. ► Emissions of CO and NO from the combustor meet the national emission limits. ► Composition of the bed material undergoes significant changes during the combustion. -- Abstract: This paper reports experimental studies on burning peanut shells in the conical fluidized-bed combustor using alumina sand as the fluidizing agent. Prior to combustion tests, hydrodynamic regimes and characteristics of a conical alumina–biomass bed were investigated under cold-state conditions for variable percentage of peanut shells in the mixture and static bed height. With selected particle sizes (300–500 μm) and static bed height (30 cm), alumina ensured bubbling fluidization regime of the bed at operating conditions specified for firing biomass. Combustion tests were performed at 60 kg/h and 45 kg/h fuel feed rates, while ranging excess air from 20% to 80% at a fixed combustor load. Temperature and gas concentrations (O 2 , CO, C x H y as CH 4 , and NO) were measured along radial and axial directions inside the reactor as well as at stack in order to characterize combustion and emission performance of the combustor for the ranges of operating conditions. For firing 60 kg/h peanut shells, excess air of 40% can be selected as an appropriate value ensuring high, about 99%, combustion efficiency and rather low emissions of CO and NO: 520 ppm and 125 ppm, respectively (both on a dry basis and at 6% O 2 ). With reducing combustor load, the combustion efficiency and emission characteristics were improved to a little extent. No evidence of bed agglomeration was found during 30-h combustion tests on this conical fluidized-bed combustor using alumina sand as the bed material. However, the timescale effect on the composition of the bed material was

Do More Hospital Beds Lead to Higher Hospitalization Rates? A Spatial Examination of Roemer’s Law

Science.gov (United States)

Delamater, Paul L.; Messina, Joseph P.; Grady, Sue C.; WinklerPrins, Vince; Shortridge, Ashton M.

2013-01-01

Background Roemer’s Law, a widely cited principle in health care policy, states that hospital beds that are built tend to be used. This simple but powerful expression has been invoked to justify Certificate of Need regulation of hospital beds in an effort to contain health care costs. Despite its influence, a surprisingly small body of empirical evidence supports its content. Furthermore, known geographic factors influencing health services use and the spatial structure of the relationship between hospital bed availability and hospitalization rates have not been sufficiently explored in past examinations of Roemer’s Law. We pose the question, “Accounting for space in health care access and use, is there an observable association between the availability of hospital beds and hospital utilization?” Methods We employ an ecological research design based upon the Anderson behavioral model of health care utilization. This conceptual model is implemented in an explicitly spatial context. The effect of hospital bed availability on the utilization of hospital services is evaluated, accounting for spatial structure and controlling for other known determinants of hospital utilization. The stability of this relationship is explored by testing across numerous geographic scales of analysis. The case study comprises an entire state system of hospitals and population, evaluating over one million inpatient admissions. Results We find compelling evidence that a positive, statistically significant relationship exists between hospital bed availability and inpatient hospitalization rates. Additionally, the observed relationship is invariant with changes in the geographic scale of analysis. Conclusions This study provides evidence for the effects of Roemer’s Law, thus suggesting that variations in hospitalization rates have origins in the availability of hospital beds. This relationship is found to be robust across geographic scales of analysis. These findings suggest

Bed agglomeration characteristics of palm shell and corncob combustion in fluidized bed

International Nuclear Information System (INIS)

Chaivatamaset, Pawin; Sricharoon, Panchan; Tia, Suvit

2011-01-01

Bed particle agglomeration was studied experimentally in an atmospheric laboratory scale fluidized bed combustor using quartz sand as bed material. Palm shell and corncob were tested. The objectives of the study were (i) to describe the contributions of the biomass ash properties and the operating conditions on the bed agglomeration tendency in term of the bed defluidization time (t def ) and the extent of potassium accumulation in the bed (K/Bed) and (ii) to further elucidate the ash inorganic behaviors and the governing bed agglomeration mechanisms. Defluidization caused by the bed agglomeration was experienced in all experiments during combustion of these biomasses, as a consequence of the presence of potassium in biomass. The experimental results indicated that biomass ash characteristics were the significant influence on the bed agglomeration. The increasing bed temperature, bed particle size and static bed height and the decreasing fluidizing air velocity enhanced the bed agglomeration tendency. The SEM/EDS analyses on the agglomerates confirmed that the agglomeration was attributed to the formation of potassium silicate liquid enriched on the surface of quartz sand particles in conjunction with the high surface temperature of the burning biomass char particles. Thermodynamic examination based on the phase diagram analysis confirmed that the molten phase formation was responsible for the agglomeration. In this study, the high molten ash fraction resulting from the high potassium content in biomass promoted the agglomeration and thus defluidization. - Highlights: → Palm shell and corncob of Thailand are tested their bed agglomeration behaviors during fluidized bed combustion. → The increase of bed temperature, bed particle size and static bed height and the decrease of air velocity enhance bed agglomeration. → The formation of ash derived potassium silicate melts enriched on sand surface is the key process. → The collision between char and sand

Development of a Quadrotor Test Bed — Modelling, Parameter Identification, Controller Design and Trajectory Generation

Directory of Open Access Journals (Sweden)

Wei Dong

2015-02-01

Full Text Available In this paper, a quadrotor test bed is developed. The technical approach for this test bed is firstly proposed by utilizing a commercial quadrotor, a Vicon motion capture system and a ground station. Then, the mathematical model of the quadrotor is formulated considering aerodynamic effects, and the parameter identification approaches for this model are provided accordingly. Based on the developed model and identified parameters, a simulation environment that is consistent with the real system is developed. Subsequently, a flight control strategy and a trajectory generation method, both of which are conceptually and computationally lightweight, are developed and tested in the simulation environment. The developed algorithms are then directly transplanted to the real system, and the experimental results show that their responses in the real-time flights match well with those from the simulations. This indicates that the control algorithms developed for the quadrotor can be preliminarily verified and refined though simulations, and then directly implemented to the real system, which could significantly reduce the experimental risks and costs. Meanwhile, real-time experiments show that the developed flight controller can efficiently stabilize the quadrotor when external disturbances exist, and the trajectory generation approach can provide safe guidance for the quadrotor to fly smoothly through cluttered environments with obstacle rings. All of these features are valuable for real applications, thus demonstrating the feasibility of further development.

Development and application of an actively controlled hybrid proton exchange membrane fuel cell - Lithium-ion battery laboratory test-bed based on off-the-shelf components

Energy Technology Data Exchange (ETDEWEB)

Yufit, V.; Brandon, N.P. [Dept. Earth Science and Engineering, Imperial College, London SW7 2AZ (United Kingdom)

2011-01-15

The use of commercially available components enables rapid prototyping and assembling of laboratory scale hybrid test-bed systems, which can be used to evaluate new hybrid configurations. The development of such a test-bed using an off-the-shelf PEM fuel cell, lithium-ion battery and DC/DC converter is presented here, and its application to a hybrid configuration appropriate for an unmanned underwater vehicle is explored. A control algorithm was implemented to regulate the power share between the fuel cell and the battery with a graphical interface to control, record and analyze the electrochemical and thermal parameters of the system. The results demonstrate the applicability of the test-bed and control algorithm for this application, and provide data on the dynamic electrical and thermal behaviour of the hybrid system. (author)

Zero cross over timing with coaxial Ge(Li) detectors

International Nuclear Information System (INIS)

El-Ibiary, M.Y.

1979-07-01

The performance of zero cross over timing systems of the constant fraction or amplitude rise time compensated type using coaxial Ge(Li) detectors is analyzed with special attention to conditions that compromise their energy-independence advantage. The outcome is verified against existing experimental results, and the parameters that lead to minimum disperson, as well as the value of the dispersion to be expected, are given by a series of charts

Status of Urban Bed Bug Infestations in Southern China: An Analysis of Pest Control Service Records in Shenzhen in 2012 and Dongguan in 2013.

Science.gov (United States)

Wang, Lei; Cai, Xuquan; Xu, Yijuan

2015-01-01

The recent resurgence of bed bugs (Cimex spp.) in many developed countries has drawn increasing attention worldwide. The status of urban bed bug infestations were investigated in Shenzhen and Dongguan, two major cities in southern Guangdong Province of southern China, based on pest control service records from two different companies (one during 2012 and another during 2013). The results showed that Shenzhen and Dongguan have a severe problem with bed bug infestations: the control of bed bugs is a constant concern, except during the winter. In Shenzhen, a similar number of premises were treated for bed bugs in central business districts and suburban districts. However, in Dongguan, more premises were treated for bed bugs in suburban districts than in central business districts. The treatment rate for worker sleeping quarters, apartments, hotel, and private houses in Shenzhen was 53.8, 43.0, 1.9, and 1.3%, respectively. The percentage of treated rooms was 56.1% for worker sleeping quarters and 91.1% for apartments. In Dongguan, the treatment rate for worker sleeping quarters, apartments, hotel, and private houses was 90.0, 10.0, 0.0, and 0.0%, respectively. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Changes in Cartilage Morphology of the Knee after 14-days of Bed Rest

Science.gov (United States)

Liphardt, A.-M.; Mündermann, A.; Koo, S.; Bäcker, N.; Andriacchi, T.; Zange, J.; Mester, J.; Heer, M.

Introduction While there are still many unanswered questions related to the effects of space flight and disuse on cartilage health and cartilage morphology the number of in vivo experiments in humans is small For muscle and bone tissue it is well known that unloading results in degeneration of those tissues Also for cartilage previous studies in patients suggest that unloading causes cartilage degeneration Studies using immobilization as a model of unloading help to investigate the importance of experiencing mechanical loads for the maintenance of healthy biological tissues The goal of our study was to investigate whether bed rest induced immobilization has a negative effect on articular cartilage in healthy subjects and if vibration training is a potential counter-measure for these negative effects Methods Eight male healthy subjects 78 1 pm 9 5 kg 179 pm 9 6 cm 26 pm 5 years performed a 14-day bed rest in 6 r -head down tilt HDT The study was designed in a cross-over-design where each subject received a training intervention vib in one phase and no intervention con in the other phase During the training intervention subjects trained 2 x 5-minutes per day at 20 Hz with 2 -- 4 mm amplitude on a vibration plate Galileo 900 Magnet resonance MR imaging of the right knee was performed to measure articular cartilage thickness MR-images 2 mm slice thickness 0 35 mm x 0 35 mm in-plane resolution 448 x 512 pixels were taken before and after bed rest to investigate the effects of bed rest

Wandering gravel-bed rivers and high-constructive stable channel sandy fluvial systems in the Ross River area, Yukon Territory, Canada

Directory of Open Access Journals (Sweden)

Darrel G.F. Long

2011-07-01

Gravel-dominated strata, inter-bedded with, and overlying coal-bearing units, are interpreted as deposits of wandering gravel-bed rivers, with sinuosity approaching 1.4. In most exposures they appear to be dominated by massive and thin planar-bedded granule to small pebble conglomerates, which would traditionally be interpreted as sheet-flood or longitudinal bar deposits of a high-gradient braided stream or alluvial fan. Architectural analysis of exposures in an open-pit shows that the predominance of flat bedding is an artefact of the geometry of the roadside exposures. In the pit the conglomerates are dominated by large scale cross stratification on a scale of 1–5.5 m. These appear to have developed as downstream and lateral accretion elements on side-bars and on in-channel bars in water depths of 2–12 m. Stacking of strata on domed 3rd order surfaces suggests development of longitudinal in-channel bar complexes similar to those observed in parts of the modern Rhône River system. Mudstone preserved in some of the channels reflects intervals of channel abandonment or avulsion. Minimum channel width is from 70 to 450 m.

Design Of Fluidized-bed Incinerator

International Nuclear Information System (INIS)

Lee, Bong Hun

1992-04-01

This book tells of design of fluidized-bed incinerator, which includes outline of fluidized-bed incinerator such as definition, characteristic, structure of principle of incineration and summary of the system, facilities of incinerator with classification of incinerator apparatus of supply of air, combustion characteristic, burnup control and point of design of incinerator, preconditioning facilities on purpose, types and characteristic of that system, a crusher, point of design of preconditioning facilities, rapid progress equipment, ventilation equipment, chimney facilities, flue gas cooling facilities boiler equipment, and removal facility of HCI/SOX and NOX.

Exercise Effects on the Brain and Sensorimotor Function in Bed Rest

Science.gov (United States)

Koppelmans, V.; Cassady, K.; De Dios, Y. E.; Szecsy, D.; Gadd, N.; Wood, S. J.; Reuter-Lorenz, R. A.; Kofman, I.; Bloomberg, J. J.; Mulavara, A. P.;

Method of online cleanliness control for upward-facing transport mirrors in integration test bed

International Nuclear Information System (INIS)

Zhao Longbiao; Qin Lang; Zhou Guorui; Ye Yayun; Zhang Chuanchao; Miao Xinxiang; Wang Hongbin; Yuan Xiaodong; Wang Xiaohong; Cheng Xiaofeng

2013-01-01

An online cleanliness control method based on the online monitoring system was developed for controlling the particle pollution and damage of upward-facing transport mirrors in the integration test bed. By building up gas knife system, the online cleanliness processing was effectively achieved for the particle pollution on the mirror surface. By using the gas screen, the cleanliness of the mirror surface was effectively online maintained. The image processing system was applied to assessing the effect of online cleanliness processing. The experimental results indicate that the particle pollution was reduced by the gas knife and the gas screen was useful to avoid the settlement of particle pollution. (authors)

Study on heat and mass transfer between a greenhouse considered as a solar air heater and a rock packed bed as ambient control system

International Nuclear Information System (INIS)

Ajona Maeztu, J.I.

1990-01-01

A general study on heat transfer in dry packed beds is made, with special emphasis in comparing different transient models and in identifying the required conditions by which the attained results are equivalent. The differences in thermal behaviour on packed beds, when simultaneous heat mass transfer occurs as wet air is used as heat transfer fluid and exchanges heat and water with the solid in the bed, is analyzed. We modelize wet packed beds considering them as one dimension adsorbents beds, with dispersive and non-dispersive models, where adsorption, condensation-evaporation and liquid water downward flow from condensate phenomena are present. Models were solved numerically and experiments with a rock bed with dry and wet air through it, were made to test assumptions and to further understand the behavior of the system, obtaining a pretty good agreement between expected and measured profiles of the temperature evolution within the packed bed. As a possible application of the wet rock bed for storage purposes, a forced ventilation greenhouse was characterized as a wet air solar heater and analyzed the energetic potential of storing the heat that has to be rejected during daytime to control the crop ambient conditions, in a rock bed for later use at night for heating. (author)

A randomized double-blind, placebo-controlled, cross-over trial (Vestparoxy) of the treatment of vestibular paroxysmia with oxcarbazepine.

Science.gov (United States)

Bayer, Otmar; Brémová, Tatiana; Strupp, Michael; Hüfner, Katharina

2018-02-01

Vestibular paroxysmia (VP) is characterized by short, often oligosymptomatic attacks of vertigo which occur spontaneously or are sometimes provoked by turning the head. Despite the description of the disease almost 40 years ago (first termed "disabling positional vertigo"), no controlled treatment trial has been published to date. The Vestparoxy trial was designed as a randomized, placebo-controlled, double-blind cross-over trial to examine the therapeutic effect of oxcarbazepine (OXA) in patients with definite or probable VP. Patients were recruited from August 2005 to December 2011 in the outpatient Dizziness Unit of the Department of Neurology of the Munich University Hospital, and randomized to receive OXA (first week: 300 mg once per day, second week: 300 mg b.i.d., third week: 300 mg t.i.d. until the end of the third month), followed by placebo or vice versa with a 1-month wash-out period in between. The primary endpoint was the number of days with one or more attacks. Secondary endpoints were the number of attacks during the observed days, and the median (for each day) duration of attacks. All these endpoints were assessed using standardized diaries collected at the end of each treatment phase. Forty-three patients were randomized, 18 patients provided usable data (2525 patient days) for at least one treatment phase and were included in the main (intention-to-treat) analysis. The most common reasons for discontinuation documented were adverse events. The risk of experiencing a day with at least one attack was 0.41 under OXA, and 0.62 under placebo treatment, yielding a relative risk of 0.67 (95% CI 0.47-0.95, p = 0.025). The number of attacks during the observed days ratio was 0.53 (95% CI 0.42-0.68, p effects.

The Safety of Hospital Beds: Ingress, Egress, and In-Bed Mobility.

Science.gov (United States)

Morse, Janice M; Gervais, Pierre; Pooler, Charlotte; Merryweather, Andrew; Doig, Alexa K; Bloswick, Donald

2015-01-01

To explore the safety of the standard and the low hospital bed, we report on a microanalysis of 15 patients' ability to ingress, move about the bed, and egress. The 15 participants were purposefully selected with various disabilities. Bed conditions were randomized with side rails up or down and one low bed with side rails down. We explored the patients' use of the side rails, bed height, ability to lift their legs onto the mattress, and ability to turn, egress, and walk back to the chair. The standard bed was too high for some participants, both for ingress and egress. Side rails were used by most participants when entering, turning in bed, and exiting. We recommend that side rails be reconsidered as a means to facilitate in-bed movement, ingress, and egress. Furthermore, single deck height settings for all patients are not optimal. Low beds as a safety measure must be re-evaluated.

Nuclear reactor control column

International Nuclear Information System (INIS)

Bachovchin, D.M.

1982-01-01

The nuclear reactor control column comprises a column disposed within the nuclear reactor core having a variable cross-section hollow channel and containing balls whose vertical location is determined by the flow of the reactor coolant through the column. The control column is divided into three basic sections wherein each of the sections has a different cross-sectional area. The uppermost section of the control column has the greatest crosssectional area, the intermediate section of the control column has the smallest cross-sectional area, and the lowermost section of the control column has the intermediate cross-sectional area. In this manner, the area of the uppermost section can be established such that when the reactor coolant is flowing under normal conditions therethrough, the absorber balls will be lifted and suspended in a fluidized bed manner in the upper section. However, when the reactor coolant flow falls below a predetermined value, the absorber balls will fall through the intermediate section and into the lowermost section, thereby reducing the reactivity of the reactor core and shutting down the reactor

Design of fluidized-bed, biological denitrification systems

International Nuclear Information System (INIS)

Patton, B.D.; Hancher, C.W.; Pitt, W.W.; Walker, J.F.

1982-01-01

Many commercial processes yield nitrate-containing wastewaters that are being discharged to the environment because traditional recovery or disposal methods are economically unacceptable. The anticipated discharge limits (i.e., 10 to 20 g (NO 3 - )/m 3 ) being considered by many states will not allow continued release of these wastewaters. The new discharge standards can be met economically by use of the fluidizied-bed, biological denitrification process. Research and development studies were conducted with 0.05-, 0.10-, 0.20-, and 0.50-m-diam fluidized-bed bioreactor systems. Feed nitrate concentrations were in the 0 to 10,000 g (NO 3 - )/m 3 range. Using the data from these studies, rate expressions were developed for the destruction of nitrate as a function of nitrate concentration. Methods were also developed for sizing bioreactors and biomass control systems. The sizing methods for fluidized-bed denitrification systems are described, and support systems such as sampling and analysis, instrumentation and controls, utilities, and bacteria storage are discussed. Operation of the process is also briefly discussed to aid the designer. Using the methods presented in this report, fluidized-bed, biological denitrification systems can be designed to treat nitrate wastewater streams

Oxidation of ethene in a wall-cooled packed-bed reactor

NARCIS (Netherlands)

Schouten, E.P.S.; Borman, P.C.; Westerterp, K.R.

1994-01-01

The selective oxidation of ethene over a silver on α-alumina catalyst was studied in a pilot plant with a wall-cooled tubular packed bed reactor. Gas and solid temperatures in the catalyst bed were measured at different axial and radial positions as well as concentrations at different axial

Treatment of epistaxis in hereditary hemorrhagic telangiectasia with tranexamic acid - a double-blind placebo-controlled cross-over phase IIIB study.

Science.gov (United States)

Geisthoff, Urban W; Seyfert, Ulrich T; Kübler, Marcus; Bieg, Birgitt; Plinkert, Peter K; König, Jochem

2014-09-01

Epistaxis is the most frequent manifestation in hereditary hemorrhagic telangiectasia, in which no optimal treatment exists. It can lead to severe anemia and reduced quality of life. Positive effects of tranexamic acid, an antifibrinolytic drug, have been reported on epistaxis related to this disorder. We sought to evaluate the efficacy of treating nosebleeds in hereditary hemorrhagic telangiectasia with tranexamic acid. In a randomized, double-blind, placebo controlled, cross-over phase IIIB study, 1 gram of tranexamic acid or placebo was given orally 3 times daily for 3 months for a total of 6 months. 22 patients were included in the intention-to-treat analysis. Hemoglobin levels, the primary outcome measure, did not change significantly (p=0.33). The secondary outcome measure was epistaxis score and patients reported a statistically significant reduction in nosebleeds, equaling a clinically relevant 54% diminution (p=0.0031), as compared to the placebo period. No severe side effects were observed. Tranexamic acid reduces epistaxis in patients with hereditary hemorrhagic telangiectasia. (Clinical trial registration numbers: BfArM 141 CHC 9008-001 and ClinicalTrials.gov NCT01031992). Copyright © 2014 Elsevier Ltd. All rights reserved.

Stress analysis of LOFT steam generator blowdown cross-over line

International Nuclear Information System (INIS)

Singh, J.N.

1978-01-01

The purpose of this report is to demonstrate compliance of the LOFT Steam Generator Blowdown Cross-Over Piping with the ASME Boiler and Pressure Vessel Code, Section III, Subsection NC. Deadweight, thermal expansion, seismic, LOCE, and LOCA loads have been considered. With the addition of two snubbers, as shown in this report, the system conforms to all requirements

The Effects of Consumption of Bread Fortified With Soy Bean Flour on Metabolic Profile in Type 2 Diabetic Women: A Cross-over Randomized Controlled Clinical Trial.

Science.gov (United States)

Moghaddam, Asma Salari; Entezari, Mohammad Hassan; Iraj, Bijan; Askari, Gholam Reza; Maracy, Mohammad Reza

2014-12-01

Diabetes mellitus is one of the most common chronic diseases in the world and has become a major threat for global health. Recent studies reported that the soy has beneficial effects in diabetic mellitus patients. The aim of this study was to assess the effects of soybean flour fortified bread consumption on metabolic profile in type 2 diabetic women. This randomized, cross-over, controlled clinical trial was carried out in 30 type 2 diabetic women. At first, a 2-week run-in period was applied. Then, participants were randomly assigned to either intervention or control groups. Participants in the intervention group were asked to replace 120 g of soybean flour fortified bread with the same amount of their usual bread intake or other cereal products for 6 weeks. After a 4 weeks washout period, participants were crossed over for another 6 weeks. Mean (±standard deviation) age and body mass index of subjects was 45.7 ± 3.8 years and 29.5 ± 3.9 kg/m(2), respectively. The results of our study showed no significant effects of soybean flour fortified bread on metabolic profile. We found a reduction in serum triglycerides (change difference: -3.7, P = 0.82), serum low-density lipoprotein-cholesterol (change difference: -11.2, P = 0.50), insulin (change difference: -3.6, P = 0.7), and homeostatic model assessment of insulin resistance (change differences: -0.57, P = 0.45) after 6 weeks but these changes were not statistically significant. No significant effects of soybean flour fortified bread on serum concentrations of fasting blood sugar, glycated hemoglobin, high-density lipoproteins and total cholesterol levels were found. Six weeks consumption of soybean flour fortified bread among diabetic patients had no significant effects on metabolic profile.

The effects of consumption of bread fortified with soy bean flour on metabolic profile in type 2 diabetic women: A cross-over randomized controlled clinical trial

Directory of Open Access Journals (Sweden)

Asma Salari Moghaddam

2014-01-01

Full Text Available Background: Diabetes mellitus is one of the most common chronic diseases in the world and has become a major threat for global health. Recent studies reported that the soy has beneficial effects in diabetic mellitus patients. The aim of this study was to assess the effects of soybean flour fortified bread consumption on metabolic profile in type 2 diabetic women. Methods: This randomized, cross-over, controlled clinical trial was carried out in 30 type 2 diabetic women. At first, a 2-week run-in period was applied. Then, participants were randomly assigned to either intervention or control groups. Participants in the intervention group were asked to replace 120 g of soybean flour fortified bread with the same amount of their usual bread intake or other cereal products for 6 weeks. After a 4 weeks washout period, participants were crossed over for another 6 weeks. Results: Mean (±standard deviation age and body mass index of subjects was 45.7 ± 3.8 years and 29.5 ± 3.9 kg/m 2 , respectively. The results of our study showed no significant effects of soybean flour fortified bread on metabolic profile. We found a reduction in serum triglycerides (change difference: -3.7, P = 0.82, serum low-density lipoprotein-cholesterol (change difference: -11.2, P = 0.50, insulin (change difference: -3.6, P = 0.7, and homeostatic model assessment of insulin resistance (change differences: -0.57, P = 0.45 after 6 weeks but these changes were not statistically significant. No significant effects of soybean flour fortified bread on serum concentrations of fasting blood sugar, glycated hemoglobin, high-density lipoproteins and total cholesterol levels were found. Conclusions: Six weeks consumption of soybean flour fortified bread among diabetic patients had no significant effects on metabolic profile.

Animal welfare in cross-ventilated, compost-bedded pack, and naturally ventilated dairy barns in the upper Midwest.

Science.gov (United States)

Lobeck, K M; Endres, M I; Shane, E M; Godden, S M; Fetrow, J

2011-11-01

The objective of this cohort study was to investigate animal welfare in 2 newer dairy housing options in the upper Midwest, cross-ventilated freestall barns (CV) and compost-bedded-pack barns (CB), compared with conventional, naturally ventilated freestall barns (NV). The study was conducted on 18 commercial dairy farms, 6 of each housing type, in Minnesota and eastern South Dakota. The primary breed in all farms was Holstein; 1 CV and 1 NV herd had approximately 30% Jersey-Holstein crossbreds. All freestall herds used sand for bedding. Farms were visited 4 times (once in each season) between January and November 2008, and approximately 93% of all animals in each pen were visually scored on each visit. Outcome-based measurements of welfare (locomotion, hock lesions, body condition score, hygiene, respiration rates, mortality, and mastitis prevalence) were collected on each farm. Lameness prevalence (proportion of cows with locomotion score ≥3 on a 1 to 5 scale, where 1=normal and 5=severely lame) in CB barns (4.4%) was lower than that in NV (15.9%) and CV (13.1%) barns. Lameness prevalence was similar between CV and NV barns. Hock lesion prevalence (proportion of cows with a lesion score ≥2 on a 1 to 3 scale, where 1=normal, 2=hair loss, and 3=swelling) was lower in CB barns (3.8%) than in CV (31.2%) and NV barns (23.9%). Hygiene scores (1 to 5 scale, where 1=clean and 5=very dirty) were higher for CB (3.18) than CV (2.83) and NV (2.77) barns, with no differences between CV and NV barns. Body condition scores, respiration rates, mastitis prevalence, culling, and mortality rates did not differ among housing systems. The CV and NV barns were evaluated using the cow comfort index (proportion of cows lying down in a stall divided by all animals touching a stall) and the stall usage index (proportion of cows lying divided by all animals in the pen not eating). The CV barns tended to have greater cow comfort index (85.9%) than the NV barns (81.4%) and had greater

Wound bed preparation for ischemic diabetic foot ulcer.

Science.gov (United States)

Zhang, Zhaoxin; Lv, Lei; Guan, Sheng

2015-01-01

This study is to evaluate the effect of allograft skin on wound angiogenesis and wound bed preparation of ischemic diabetic foot ulcer. A total of 60 cases of patients with diabetic foot ulcer were randomly divided into the experimental group (n = 30) and the control group (n = 30). After debridement, in the experimental group, allograft skin was used to cover the wound while in the control group, vaseline and gauze was used to cover the wound. The wound was opened and dressed at 3, 5, 7, 14 days after operation and the growth condition of the granulation tissue was observed and recorded. The wound bed preparation time of the experimental group was 14.37 ± 1.06 days, compared with the control group 25.99 ± 4.03 days, there was statistically significant difference (t = 14.78, P cure time of the experimental group was 32 ± 1.93 days and this time was significantly shortened than the control group 39.73 ± 2.55 days (t = 12.521, P ulcer and shorten the wound bed preparation time and treatment cycle.

PIT-tagged particle study of bed mobility in a Maine salmon river impacted by logging activities

Science.gov (United States)

Thompson, D. M.; Fixler, S. A.; Roberts, K. E.; McKenna, M.; Marshall, A. E.; Koenig, S.

2017-12-01

Presenting an interim report on a study on the Narraguagus River in Maine, which utilizes laser total stations cross-sectional surveys and tracking of passive integrated transponder (PIT) tags embedded in glass spheres to document changes in channel-bed characteristics associated with large wood (LW) additions and natural spawning activities. In 2016, work was initiated to monitor changes in bed elevation and sediment mobility with the addition of LW to the Narraguagus River as part of a restoration effort. Ten cross-sections, spaced 5-m apart, were established and surveyed with a laser total station in each of three different study reaches. The study sites include a control reach, a section with anticipated spawning activities and a site with ongoing LW placement. A grid of 200 glass spheres embedded with PIT tags, with twenty alternating 25-mm and 40-mm size particles equally spaced along each of the ten transects, were placed to serve as point sensors to detect sediment mobilization within each reach. In 2017, the site was revisited to determine if differences in PIT-tagged tracer particle mobilization reflect locations were LW was added and places where Atlantic salmon (Salmo salar) and sea lamprey (Petromyzon marinus) construct spawning redds. The positions of PIT-tagged tracer particles was recorded, but particles were not disturbed or uncovered to permit study of potential reworking of buried tracer particles the following year. Full tracer particle recovery will be determined in 2018 to determine if depths of tracer burial and changes in bed elevation vary among places near redds, LW and main channel locations. The data will be used to determine if salmon redds are preferentially located in either places with greater evidence of sediment reworking or alternatively in stable areas? The study will help determine the degree of bed disruption associated with spawning activities and whether LW placement encourages similar sediment mobilization processes.

Fluidized bed volume reduction of diverse radwastes

International Nuclear Information System (INIS)

McFee, J.N.; McConnell, J.W.; Waddoups, D.A.; Gray, M.F.; Harwood, L.E.; Clayton, N.J.; Drown, D.C.

1981-01-01

Method and apparatus for a fluidized bed radwaste volume reduction system are claimed. Low level radioactive wastes, combustible solids, ion exchange resins and filter sludges, and liquids, emanating from a reactor facility are introduced separately through an integrated waste influent system into a common fluidized bed vessel where volume reduction either through incineration or calcination occurs. Addition of a substance to the ion exchange resin before incineration inhibits the formation of low-melting point materials which tend to form clinkers in the bed. Solid particles are scrubbed or otherwise removed from the gaseous effluent of the vessel in an off-gas system, before the cooled and cleaned off-gas is released to the atmosphere. Iodine is chemically or physically removed from the off-gas. Otherwise, the only egress materials from the volume reduction system are containerized dry solids and tramp material. The bed material used during each mode may be circulated, cleaned, stored and exchanged from within the bed vessel by use of a bed material handling system. An instrumentation and control system provides operator information, monitors performance characteristics, implements start up and shut down procedures, and initiates alarms and emergency procedures during abnormal conditions

Hydrogeochemistry and coal-associated bacterial populations from a methanogenic coal bed

Science.gov (United States)

Barnhart, Elliott P.; Weeks, Edwin P.; Jones, Elizabeth J.P.; Ritter, Daniel J.; McIntosh, Jennifer C.; Clark, Arthur C.; Ruppert, Leslie F.; Cunningham, Alfred B.; Vinson, David S.; Orem, William H.; Fields, Matthew W.

2016-01-01

Biogenic coalbed methane (CBM), a microbially-generated source of natural gas trapped within coal beds, is an important energy resource in many countries. Specific bacterial populations and enzymes involved in coal degradation, the potential rate-limiting step of CBM formation, are relatively unknown. The U.S. Geological Survey (USGS) has established a field site, (Birney test site), in an undeveloped area of the Powder River Basin (PRB), with four wells completed in the Flowers-Goodale coal bed, one in the overlying sandstone formation, and four in overlying and underlying coal beds (Knoblach, Nance, and Terret). The nine wells were positioned to characterize the hydraulic conductivity of the Flowers-Goodale coal bed and were selectively cored to investigate the hydrogeochemistry and microbiology associated with CBM production at the Birney test site. Aquifer-test results indicated the Flowers-Goodale coal bed, in a zone from about 112 to 120 m below land surface at the test site, had very low hydraulic conductivity (0.005 m/d) compared to other PRB coal beds examined. Consistent with microbial methanogenesis, groundwater in the coal bed and overlying sandstone contain dissolved methane (46 mg/L average) with low δ13C values (−67‰ average), high alkalinity values (22 meq/kg average), relatively positive δ13C-DIC values (4‰ average), and no detectable higher chain hydrocarbons, NO3−, or SO42−. Bioassay methane production was greatest at the upper interface of the Flowers-Goodale coal bed near the overlying sandstone. Pyrotag analysis identified Aeribacillus as a dominant in situbacterial community member in the coal near the sandstone and statistical analysis indicated Actinobacteria predominated coal core samples compared to claystone or sandstone cores. These bacteria, which previously have been correlated with hydrocarbon-containing environments such as oil reservoirs, have demonstrated the ability to produce biosurfactants to break down

BedMachine v3: Complete Bed Topography and Ocean Bathymetry Mapping of Greenland From Multibeam Echo Sounding Combined With Mass Conservation

DEFF Research Database (Denmark)

Morlighem, M.; Williams, C. N.; Rignot, E.

2017-01-01

Greenland's bed topography is a primary control on ice flow, grounding line migration, calving dynamics, and subglacial drainage. Moreover, fjord bathymetry regulates the penetration of warm Atlantic water (AW) that rapidly melts and undercuts Greenland's marine‐terminating glaciers. Here we...... present a new compilation of Greenland bed topography that assimilates seafloor bathymetry and ice thickness data through a mass conservation approach. A new 150 m horizontal resolution bed topography/bathymetric map of Greenland is constructed with seamless transitions at the ice/ocean interface...

Study of Fluidized-Bed Control Rods; Etude de Barres de Controle Fluidisees; Izuchenie reguliruyushchej sistemy, ispol'zuyushchej suspenziyu pogloshchayushchikh chastits; Estudio Sobre Barras de Control de Lecho Fluidificado

Energy Technology Data Exchange (ETDEWEB)

Blair, D. J. [General Nuclear Engineering Corporation, Dunedin, FL (United States); Driscoll, M. J.; Dalton, G. R.; Parkinson, T. F. [Department of Nuclear Engineering, University of Florida, Gainesville, FL (United States)

1964-06-15

Control of nuclear reactors with fluidized-bed control rods (FBCR) has been previously proposed; but, despite some apparent advantages over electromechanical systems, such rods have not received widespread attention. With the FBCR concept, the reactor control system becomes a flow-regulating system using either variable-speed pumps or motor-driven control valves in the main coolant. Alternatively, in-core by-pass piping similar to control systems now being developed for fluidized-bed reactors may be utilized. Some of the possible advantages of the FBCR concept are as follows: (1) Most pressure-vessel head penetrations are eliminated, and refueling is simplified; (2) Automatic scram results from a loss-of-flow accident; (3) Axial power can be shaped by the use of contoured channels or variable-sized particles; (4). Water-gap flux peaking can be reduced for the partially withdrawn control rod; (5) The temperature reactivity allowance may be reduced if the fluidized control rods have a negative temperature coefficient; and (6) Fabrication costs are much lower than for electromechanical systems. An evaluation of the FBCR concept, including construction of prototype models and testing of the hydraulic and nuclear characteristics, has been performed. Two types of rods were studied: transmission rods (thickness Less-Than-Over-Equal-To 2 mean-free-paths) and reflection rods (thickness Less-Than-Over-Equal-To 4 mean-free-paths). Acceptable hydraulic and nuclear characteristics are possible with both types. The feasibility of controlling low-power reactors by either transmission- or reflection-type fluidized.-bed control rods has been established. Furthermore, it was shown that the FBCR concept has good control properties which may be calculated by standard theoretical methods. For high-power, high-temperature applications, additional information on particle material characteristics is needed. A great advantage offered by the FBCR is the possibility of shaping the axial flux

Literature review for Texas Department of Transportation Research Project 0-4695: Guidance for design in areas of extreme bed-load mobility, Edwards Plateau, Texas

Science.gov (United States)

Heitmuller, Franklin T.; Asquith, William H.; Fang, Xing; Thompson, David B.; Wang, Keh-Han

2005-01-01

A review of the literature addressing sediment transport in gravel-bed river systems and structures designed to control bed-load mobility is provided as part of Texas Department of Transportation research project 0–4695: Guidance for Design in Areas of Extreme Bed-Load Mobility. The study area comprises the western half of the Edwards Plateau in central Texas. Three primary foci of the literature review are journal articles, edited volumes, and government publications. Major themes within the body of literature include deterministic sediment transport theory and equations, development of methods to measure and analyze fluvial sediment, applications and development of theory in natural channels and flume experiments, and recommendations for river management and structural design. The literature review provides an outline and foundation for the research project to characterize extreme bed-load mobility in rivers and streams across the study area. The literature review also provides a basis upon which potential modifications to low-water stream-crossing design in the study area can be made.

7 CFR 2902.15 - Bedding, bed linens, and towels.

Science.gov (United States)

2010-01-01

... PROCUREMENT Designated Items § 2902.15 Bedding, bed linens, and towels. (a) Definition. (1) Bedding is that... minimum biobased content is 12 percent and shall be based on the amount of qualifying biobased carbon in..., and silk are not qualifying biobased feedstocks for the purpose of determining the biobased content of...

Predictors of over-the-counter medication: A cross-sectional Indian study

OpenAIRE

Abinash Panda; Supriya Pradhan; Gurukrushna Mohapatro; Jaya Singh Kshatri

2017-01-01

Context: The determinants of over-the-counter (OTC) medication need to be understood to design adequate drug information policies. Aim: To determine the prevalence and predictors of OTC medication among the adult population of Berhampur town in Odisha, India. Settings and Design: It was a prospective, cross-sectional, observational study carried out in the private retail pharmacy on a convenience sample of 880 adults over a period of 6 months at Berhampur, Odisha, India. Materials and Methods...

Improvement of the crossed undulator design for effective circular polarization control in X-ray FELs

Energy Technology Data Exchange (ETDEWEB)

Geloni, Gianluca [European XFEL GmbH, Hamburg (Germany); Kocharyan, Vitali; Saldin, Evgeni [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

2011-01-15

The production of X-ray radiation with a high degree of circular polarization constitutes an important goal at XFEL facilities. A simple scheme to obtain circular polarization control with crossed undulators has been proposed so far. In its simplest configuration the crossed undulators consist of pair of short planar undulators in crossed position separated by an electromagnetic phase shifter. An advantage of this configuration is a fast helicity switching. A drawback is that a high degree of circular polarization (over 90 %) can only be achieved for lengths of the insertion devices significantly shorter than the gain length, i.e. at output power significantly lower than the saturation power level. The obvious and technically possible extension considered in this paper, is to use a setup with two or more crossed undulators separated by phase shifters. This cascade crossed undulator scheme is distinguished, in performance, by a fast helicity switching, a high degree of circular polarization (over 95%) and a high output power level, comparable with the saturation power level in the baseline undulator at fundamental wavelength. We present feasibility study and exemplifications for the LCLS baseline in the soft X-ray regime. (orig.)

How dynamic are ice-stream beds?

Science.gov (United States)

Davies, Damon; Bingham, Robert G.; King, Edward C.; Smith, Andrew M.; Brisbourne, Alex M.; Spagnolo, Matteo; Graham, Alastair G. C.; Hogg, Anna E.; Vaughan, David G.

2018-05-01

Projections of sea-level rise contributions from West Antarctica's dynamically thinning ice streams contain high uncertainty because some of the key processes involved are extremely challenging to observe. An especially poorly observed parameter is sub-decadal stability of ice-stream beds, which may be important for subglacial traction, till continuity and landform development. Only two previous studies have made repeated geophysical measurements of ice-stream beds at the same locations in different years, but both studies were limited in spatial extent. Here, we present the results from repeat radar measurements of the bed of Pine Island Glacier, West Antarctica, conducted 3-6 years apart, along a cumulative ˜ 60 km of profiles. Analysis of the correlation of bed picks between repeat surveys shows that 90 % of the bed displays no significant change despite the glacier increasing in speed by up to 40 % over the last decade. We attribute the negligible detection of morphological change at the bed of Pine Island Glacier to the ubiquitous presence of a deforming till layer, wherein sediment transport is in steady state, such that sediment is transported along the basal interface without inducing morphological change to the radar-sounded basal interface. Given the precision of our measurements, the upper limit of subglacial erosion observed here is 500 mm a-1, far exceeding erosion rates reported for glacial settings from proglacial sediment yields, but substantially below subglacial erosion rates of 1.0 m a-1 previously reported from repeat geophysical surveys in West Antarctica.

A Cross-Layer Approach in Sensing and Resource Allocation for Multimedia Transmission over Cognitive UWB Networks

Directory of Open Access Journals (Sweden)

Lo ACC

2010-01-01

Full Text Available We propose an MAC centric cross-layer approach to address the problem of multimedia transmission over cognitive Ultra Wideband (C-UWB networks. Several fundamental design issues, which are related to application (APP, medium access control (MAC, and physical (PHY layer, are discussed. Although substantial research has been carried out in the PHY layer perspective of cognitive radio system, this paper attempts to extend the existing research paradigm to MAC and APP layers, which can be considered as premature at this time. This paper proposed a cross-layer design that is aware of (a UWB wireless channel conditions, (b time slot allocations at the MAC layer, and (c MPEG-4 video at the APP layer. Two cooperative sensing mechanisms, namely, AND and OR, are analyzed in terms of probability of detection ( , probability of false alarm ( , and the required sensing period. Then, the impact of sensing scheduling to the MPEG-4 video transmission over wireless cognitive UWB networks is observed. In addition, we also proposed the packet reception rate- (PRR- based resource allocation scheme that is aware of the channel condition, target PRR, and queue status.

Temporal and spatial variability in thalweg profiles of a gravel-bed river

Science.gov (United States)

Madej, Mary Ann

1999-01-01

This study used successive longitudinal thalweg profiles in gravel-bed rivers to monitor changes in bed topography following floods and associated large sediment inputs. Variations in channel bed elevations, distributions of residual water depths, percentage of channel length occupied by riffles, and a spatial autocorrelation coefficient (Moran's I) were used to quantify changes in morphological diversity and spatial structure in Redwood Creek basin, northwestern California. Bed topography in Redwood Creek and its major tributaries consists primarily of a series of pools and riffles. The size, frequency and spatial distribution of the pools and riffles have changed significantly during the past 20 years. Following large floods and high sediment input in Redwood Creek and its tributaries in 1975, variation in channel bed elevations was low and the percentage of the channel length occupied by riffles was high. Over the next 20 years, variation in bed elevations increased while the length of channel occupied by riffles decreased. An index [(standard deviation of residual water depth/bankfull depth) × 100] was developed to compare variations in bed elevation over a range of stream sizes, with a higher index being indicative of greater morphological diversity. Spatial autocorrelation in the bed elevation data was apparent at both fine and coarse scales in many of the thalweg profiles and the observed spatial pattern of bed elevations was found to be related to the dominant channel material and the time since disturbance. River reaches in which forced pools dominated, and in which large woody debris and bed particles could not be easily mobilized, exhibited a random distribution of bed elevations. In contrast, in reaches where alternate bars dominated, and both wood and gravel were readily transported, regularly spaced bed topography developed at a spacing that increased with time since disturbance. This pattern of regularly spaced bed features was reversed

OverWatch: A Cross-Plane DDoS Attack Defense Framework with Collaborative Intelligence in SDN

Directory of Open Access Journals (Sweden)

Biao Han

2018-01-01

Full Text Available Distributed Denial of Service (DDoS attacks are one of the biggest concerns for security professionals. Traditional middle-box based DDoS attack defense is lack of network-wide monitoring flexibility. With the development of software-defined networking (SDN, it becomes prevalent to exploit centralized controllers to defend against DDoS attacks. However, current solutions suffer with serious southbound communication overhead and detection delay. In this paper, we propose a cross-plane DDoS attack defense framework in SDN, called OverWatch, which exploits collaborative intelligence between data plane and control plane with high defense efficiency. Attack detection and reaction are two key procedures of the proposed framework. We develop a collaborative DDoS attack detection mechanism, which consists of a coarse-grained flow monitoring algorithm on the data plane and a fine-grained machine learning based attack classification algorithm on the control plane. We propose a novel defense strategy offloading mechanism to dynamically deploy defense applications across the controller and switches, by which rapid attack reaction and accurate botnet location can be achieved. We conduct extensive experiments on a real-world SDN network. Experimental results validate the efficiency of our proposed OverWatch framework with high detection accuracy and real-time DDoS attack reaction, as well as reduced communication overhead on SDN southbound interface.

Rock bed heat accumulators. Final report

Energy Technology Data Exchange (ETDEWEB)

Riaz, M.

1977-12-01

The principal objectives of the research program on rock bed heat accumulators (or RBHA) are: (1) to investigate the technical and economic feasibility of storing large amounts of thermal energy (in the tens of MWt range) at high temperature (up to 500/sup 0/C) over extended periods of time (up to 6 months) using native earth or rock materials; (2) to conduct studies to establish the performance characteristics of large rock bed heat accumulators at various power and temperature levels compatible with thermal conversion systems; and (3) to assess the materials and environmental problems associated with the operation of such large heat accumulators. Results of the study indicate that rock bed heat accumulators for seasonal storage are both technically and economically feasible, and hence could be exploited in various applications in which storage plays an essential role such as solar power and total energy systems, district and cogeneration heating systems.

Petechiae: reproducible pattern of distribution and increased appearance after bed rest.

Science.gov (United States)

Ganse, Bergita; Limper, Ulrich; Bühlmeier, Judith; Rittweger, Jörn

2013-08-01

Exposure to acceleration can cause petechial hemorrhages, called G measles. Petechiae usually start to develop between 5 and 9 G with a high interindividual variance. Centrifuge training delays the onset to higher G levels. One might expect onset at lower G levels after bed rest; however, there is no evidence in the literature. A case of petechiae formation after bed rest is presented here. Orthostatic tolerance was tested using a tilt table and lower body negative pressure before and after bed rest in both campaigns of a 2 x 21-d bed rest study with 6 degrees head-down tilt. A 42-yr-old male Caucasian without any history of thrombosis, venous disease, hemorrhage, or petechiae, and with a negative thrombophilia screening, took part in the bed rest study as 1 out of 10 subjects. He was the only one to develop petechiae during the orthostatic tests after, but not before, bed rest in both campaigns. Petechiae were distributed throughout the lower legs and most pronounced at the shin in a stocking-like fashion, surprisingly reoccurring in an identical pattern of distribution. Petechiae appeared slowly over minutes during hyperemia. This case indicates that prolonged bed rest decreases the threshold for petechiae formation. A reproducible distribution pattern suggests that factors predisposing to petechiae formation keep their local distribution over time (possibly due to local vessel structures). Mechanisms of adaptation and interindividual variance are unclear. Findings are of clinical relevance as such cases might occur after prolonged bed rest in patients without need of expensive testing.

Focal Gray Matter Plasticity as a Function of Long Duration Head-down Tilt Bed Rest

Science.gov (United States)

Koppelmans, V.; DeDios, Y. E.; Wood, S. J.; Reuter-Lorenz, P. A.; Kofman, I.; Bloomberg, J. J.; Mulavara, A. P.; Koppelmans, V.

2014-01-01

Long duration spaceflight (i.e., > or = 22 days) has been associated with changes in sensorimotor systems, resulting in difficulties that astronauts experience with posture control, locomotion, and manual control. The microgravity environment is an important causal factor for spaceflight induced sensorimotor changes. Whether these sensorimotor changes may be related to structural and functional brain changes is yet unknown. However, experimental studies revealed changes in the gray matter (GM) of the brain after simulated microgravity. Thus, it is possible that spaceflight may affect brain structure and thereby cognitive functioning and motor behavior. Long duration head-down tilt bed rest has been suggested as an exclusionary analog to study microgravity effects on the sensorimotor system. Bed rest mimics microgravity in body unloading and bodily fluid shifts. In consideration of the health and performance of crewmembers both in- and post-flight, we are conducting a prospective longitudinal 70-day bed rest study as an analog to investigate the effects of microgravity on the brain. VBM analysis revealed a progressive decrease from pre- to in- bed rest in GM volume in bilateral areas including the frontal medial cortex, the insular cortex and the caudate. Over the same time period, there was a progressive increase in GM volume in the cerebellum, occipital-, and parietal cortex, including the precuneus. The majority of these changes did not fully recover during the post-bed rest period. Analysis of lobular GM volumes obtained with BRAINS showed significantly increased volume from pre-bed rest to in-bed rest in GM of the parietal lobe and the third ventricle. Temporal GM volume at 70 days in bed rest was smaller than that at the first pre-bed rest measurement. Trend analysis showed significant positive linear and negative quadratic relationships between parietal GM and time, a positive linear relationship between third ventricle volume and time, and a negative linear

The mechanism of char ignition in fluidized bed combustors

NARCIS (Netherlands)

Siemons, R.V.

1987-01-01

Knowledge about ignition processes of coal in fluidized beds is of importance for the start-up and dynamic control of these combustors. Initial experiments in a transparent fluidized bed scale model showed the existence of a considerable induction period for the ignition of char, especially at low

Low latency adaptive streaming of HD H.264 video over 802.11 wireless networks with cross-layer feedback

Science.gov (United States)

Patti, Andrew; Tan, Wai-tian; Shen, Bo

2007-09-01

Streaming video in consumer homes over wireless IEEE 802.11 networks is becoming commonplace. Wireless 802.11 networks pose unique difficulties for streaming high definition (HD), low latency video due to their error-prone physical layer and media access procedures which were not designed for real-time traffic. HD video streaming, even with sophisticated H.264 encoding, is particularly challenging due to the large number of packet fragments per slice. Cross-layer design strategies have been proposed to address the issues of video streaming over 802.11. These designs increase streaming robustness by imposing some degree of monitoring and control over 802.11 parameters from application level, or by making the 802.11 layer media-aware. Important contributions are made, but none of the existing approaches directly take the 802.11 queuing into account. In this paper we take a different approach and propose a cross-layer design allowing direct, expedient control over the wireless packet queue, while obtaining timely feedback on transmission status for each packet in a media flow. This method can be fully implemented on a media sender with no explicit support or changes required to the media client. We assume that due to congestion or deteriorating signal-to-noise levels, the available throughput may drop substantially for extended periods of time, and thus propose video source adaptation methods that allow matching the bit-rate to available throughput. A particular H.264 slice encoding is presented to enable seamless stream switching between streams at multiple bit-rates, and we explore using new computationally efficient transcoding methods when only a high bit-rate stream is available.

Development of a mobile sensor for robust assessment of river bed grain forces

Science.gov (United States)

Maniatis, G.; Hoey, T.; Sventek, J.; Hodge, R. A.

2013-12-01

The forces experienced by sediment grains at entrainment and during transport, and those exerted on river beds, are significant for the development of river systems and landscape evolution. The assessment of local grain forces has been approached using two different methodologies. The first approach uses static impact sensors at points or cross-sections to measure velocity and/or acceleration. A second approach uses mobile natural or artificial 'smart' pebbles instrumented with inertia micro-sensors for directly measuring the local forces experienced by individual grains. The two approaches have yielded significantly different magnitudes of impact forces. Static sensors (piezoelectric plates connected to accelerometers) temporally smooth the impacts from several grains and infrequently detect the higher forces (up to ×100g) generated by direct single-grain impacts. The second method is currently unable to record the full range of impacts in real rivers due to the low measurement range of the deployed inertia sensors (×3g). Laboratory applications have required only low-range accelerometers, so excluding the magnitude of natural impacts from the design criteria. Here we present the first results from the development of a mobile sensor, designed for the purpose of measuring local grain-forces in a natural riverbed. We present two sets of measurements. The first group presents the calibration of a wide range micro-accelerometer from a set of vertical drop experiments (gravitational acceleration) and further experiments on a shaking table moving with pre-defined acceleration. The second group of measurements are from incipient motion experiments performed in a 9m x0.9m flume (slope 0.001 to 0.018) under steadily increasing discharge. Initially the spherical sensor grain was placed on an artificial surface of hemispheres of identical diameter to the sensor (111mm). Incipient motion was assessed under both whole and half-diameter exposure for each slope. Subsequently

Thermal fatigue and creep evaluation for the bed in tritium SDS

Energy Technology Data Exchange (ETDEWEB)

Choi, Woo-seok, E-mail: wschoi@kaeri.re.kr [Korea Atomic Energy Research Institute, Yuseong, Daejeon (Korea, Republic of); Park, Chang-gyu [Korea Atomic Energy Research Institute, Yuseong, Daejeon (Korea, Republic of); Ju, Yong-sun [KOASIS, Yuseong, Daejeon (Korea, Republic of); Kang, Hyun-goo; Jang, Min-ho; Yun, Sei-hun [National Fusion Research Institute, Yuseong, Daejeon (Korea, Republic of)

2016-11-01

Highlights: • To evaluate the integrity of the ITER tritium SDS bed, three kinds of assessments were conducted. • The structural analysis showed that the stress induced from the thermal load and the internal pressure is within the design stress intensity. • The combined fatigue and creep assessment was also performed according to the procedure of ASME code Subsection NH. • A new operation procedure to obtain more integrity margin was recommended. • The other operation procedure could be considered which makes the rapid operation possible giving up the marginal integrity. - Abstract: The primary vessel of ITER tritium SDS bed is made of stainless steel. It is heated beyond 500 °C to desorb tritium. During this process the primary vessel is subject to thermal stress. And it is also subject to thermal fatigue by the iterative process of absorption and desorption. In addition, its operation temperature range is in the thermal creep temperature region. Therefore, the tritium SDS bed should have sufficient design stress intensity under the high temperature operating conditions. It should also be free of damage due to fatigue during the design life. Thermal analysis and structural analysis was performed using a finite element method to calculate the temperature and the stress distribution of the ITER tritium SDS bed due to the internal pressure and thermal loads. The thermal fatigue and creep effects were also evaluated since the tritium SDS bed was heated to hot temperature region where creep occurs. Based on the distribution of the primary stress and secondary stress results, two evaluation cross-sections were selected. The evaluation showed that the calculated value on the cross-sections satisfied all of the limits of the design code requirements.

Heat Transfer in a Fixed Bed of Straw Char

DEFF Research Database (Denmark)

Fjellerup, Jan Søren; Henriksen, Ulrik Birk; Jensen, Anker

2003-01-01

A model for the thermal conductivity of a straw char bed has been developed. The model extends the work of Yagi and Kunii to describe heat transfer in a bed of cylinders, using a relationship between the interparticle distance and the external porosity. To verify the model, thermal conductivity...... the experimental uncertainty over the range of conditions investigated. The heat transfer model was used in a parametric study to evaluate the effect of gas flow rate, particle diameter, porosity, and temperature on the thermal conductivity in a straw char bed....... experiments were performed on shredded and un-shredded straw char samples, varying particle size, bed packing (loose or dense), and temperature. Predictions with the model, using the measured external porosity and particle diameter as input parameters, are in agreement with measurements within...

Cardiac atrophy after bed rest and spaceflight

Science.gov (United States)

Perhonen, M. A.; Franco, F.; Lane, L. D.; Buckey, J. C.; Blomqvist, C. G.; Zerwekh, J. E.; Peshock, R. M.; Weatherall, P. T.; Levine, B. D.

2001-01-01

Cardiac muscle adapts well to changes in loading conditions. For example, left ventricular (LV) hypertrophy may be induced physiologically (via exercise training) or pathologically (via hypertension or valvular heart disease). If hypertension is treated, LV hypertrophy regresses, suggesting a sensitivity to LV work. However, whether physical inactivity in nonathletic populations causes adaptive changes in LV mass or even frank atrophy is not clear. We exposed previously sedentary men to 6 (n = 5) and 12 (n = 3) wk of horizontal bed rest. LV and right ventricular (RV) mass and end-diastolic volume were measured using cine magnetic resonance imaging (MRI) at 2, 6, and 12 wk of bed rest; five healthy men were also studied before and after at least 6 wk of routine daily activities as controls. In addition, four astronauts were exposed to the complete elimination of hydrostatic gradients during a spaceflight of 10 days. During bed rest, LV mass decreased by 8.0 +/- 2.2% (P = 0.005) after 6 wk with an additional atrophy of 7.6 +/- 2.3% in the subjects who remained in bed for 12 wk; there was no change in LV mass for the control subjects (153.0 +/- 12.2 vs. 153.4 +/- 12.1 g, P = 0.81). Mean wall thickness decreased (4 +/- 2.5%, P = 0.01) after 6 wk of bed rest associated with the decrease in LV mass, suggesting a physiological remodeling with respect to altered load. LV end-diastolic volume decreased by 14 +/- 1.7% (P = 0.002) after 2 wk of bed rest and changed minimally thereafter. After 6 wk of bed rest, RV free wall mass decreased by 10 +/- 2.7% (P = 0.06) and RV end-diastolic volume by 16 +/- 7.9% (P = 0.06). After spaceflight, LV mass decreased by 12 +/- 6.9% (P = 0.07). In conclusion, cardiac atrophy occurs during prolonged (6 wk) horizontal bed rest and may also occur after short-term spaceflight. We suggest that cardiac atrophy is due to a physiological adaptation to reduced myocardial load and work in real or simulated microgravity and demonstrates the plasticity

Airborne bacterial dispersal during and after dressing and bed changes on burns patients.

Science.gov (United States)

Bache, Sarah E; Maclean, Michelle; Gettinby, George; Anderson, John G; MacGregor, Scott J; Taggart, Ian

2015-02-01

It is acknowledged that activities such as dressing changes and bed sheet changes are high-risk events; creating surges in levels of airborne bacteria. Burns patients are particularly high dispersers of pathogens; due to their large, often contaminated, wound areas. Prevention of nosocomial cross-contamination is therefore one of the major challenges faced by the burns team. In order to assess the contribution of airborne spread of bacteria, air samples were taken repeatedly throughout and following these events, to quantify levels of airborne bacteria. Air samples were taken at 3-min intervals before, during and after a dressing and bed change on a burns patient using a sieve impaction method. Following incubation, bacterial colonies were enumerated to calculate bacterial colony forming units per m(3) (cfu/m(3)) at each time point. Statistical analysis was performed, whereby the period before the high-risk event took place acted as a control period. The periods during and after the dressing and bed sheet changes were examined for significant differences in airborne bacterial levels relative to the control period. The study was carried out four times, on three patients with burns between 35% total burn surface area (TBSA) and 51% TBSA. There were significant increases in airborne bacteria levels, regardless of whether the dressing change or bed sheet change took place first. Of particular note, is the finding that significantly high levels (up to 2614cfu/m(3)) of airborne bacteria were shown to persist for up to approximately 1h after these activities ended. This is the most accurate picture to date of the rapidly changing levels of airborne bacteria within the room of a burns patient undergoing a dressing change and bed change. The novel demonstration of a significant increase in the airborne bacterial load during these events has implications for infection control on burns units. Furthermore, as these increased levels remained for approximately 1h afterwards

Coevolution of bed surface patchiness and channel morphology: 2. Numerical experiments

Science.gov (United States)

Nelson, Peter A.; McDonald, Richard R.; Nelson, Jonathan M.; Dietrich, William E.

2015-01-01

In gravel bed rivers, bed topography and the bed surface grain size distribution evolve simultaneously, but it is not clear how feedbacks between topography and grain sorting affect channel morphology. In this, the second of a pair of papers examining interactions between bed topography and bed surface sorting in gravel bed rivers, we use a two-dimensional morphodynamic model to perform numerical experiments designed to explore the coevolution of both free and forced bars and bed surface patches. Model runs were carried out on a computational grid simulating a 200 m long, 2.75 m wide, straight, rectangular channel, with an initially flat bed at a slope of 0.0137. Over five numerical experiments, we varied (a) whether an obstruction was present, (b) whether the sediment was a gravel mixture or a single size, and (c) whether the bed surface grain size feeds back on the hydraulic roughness field. Experiments with channel obstructions developed a train of alternate bars that became stationary and were connected to the obstruction. Freely migrating alternate bars formed in the experiments without channel obstructions. Simulations incorporating roughness feedbacks between the bed surface and flow field produced flatter, broader, and longer bars than simulations using constant roughness or uniform sediment. Our findings suggest that patches are not simply a by-product of bed topography, but they interact with the evolving bed and influence morphologic evolution.

Overview and evolution of the LeRC PMAD DC test bed

Science.gov (United States)

Soeder, James F.; Frye, Robert J.

1992-01-01

Since the beginning of the Space Station Freedom Program (SSFP), the Lewis Research Center (LeRC) has been developed electrical power system test beds to support the overall design effort. Through this time, the SSFP has changed the design baseline numerous times, however, the test bed effort has endeavored to track these changes. Beginning in August 1989 with the baseline and an all DC system, a test bed was developed to support the design baseline. The LeRC power measurement and distribution (PMAD) DC test bed and the changes in the restructure are described. The changes included the size reduction of primary power channel and various power processing elements. A substantial reduction was also made in the amount of flight software with the subsequent migration of these functions to ground control centers. The impact of these changes on the design of the power hardware, the controller algorithms, the control software, and a description of their current status is presented. An overview of the testing using the test bed is described, which includes investigation of stability and source impedance, primary and secondary fault protection, and performance of a rotary utility transfer device. Finally, information is presented on the evolution of the test bed to support the verification and operational phases of the SSFP in light of these restructure scrubs.

A randomized, double-blind, crossover comparison of novel continuous bed motion versus traditional bed position whole-body PET/CT imaging

International Nuclear Information System (INIS)

Schatka, Imke; Weiberg, Desiree; Reichelt, Stephanie; Owsianski-Hille, Nicole; Derlin, Thorsten; Berding, Georg; Bengel, Frank M.

2016-01-01

Continuous bed motion has recently been introduced for whole-body PET/CT, and represents a paradigm shift towards individualized and flexible acquisition without the limitations of bed position-based planning. Increased patient comfort due to lack of abrupt table position changes may be another albeit still unproven advantage. For robust clinical implementation, image quality and quantitative accuracy should at least be equal to the prior standard of bed position-based step-and-shoot imaging. The study included 68 consecutive patients referred for whole-body PET/CT for various malignancies. The patients underwent traditional step-and-shoot and novel continuous bed motion acquisition in the same session in a randomized crossover design. The patients and two independent observers were blinded to the sequence of scan techniques. Patient comfort/satisfaction was examined using a standardized questionnaire. SUVs were compared for reference tissue (liver, muscle) and tumour lesions. PET image quality and misalignment with CT images were evaluated on a scale of 1 - 4. Patients preferred continuous bed motion over step-and-shoot (P = 0.0001). It was considered to be more relaxing (38 % vs. 8 %), quieter (34 % vs. 8 %), and more fluid (64 % vs. 8 %). Image quality, SUV and CT misalignment did not differ between the techniques. Continuous bed motion resulted in better end-plane image quality (P < 0.0001). Regardless of the technique, second examinations had significantly higher tumour lesion SUVmax values (P = 0.0002), and a higher CT misalignment score (P = 0.0017). Oncological PET/CT with continuous bed motion enhances patient comfort and is associated with image quality at least comparable to that with traditional bed position-based step-and-shoot acquisition. (orig.)

A randomized, double-blind, crossover comparison of novel continuous bed motion versus traditional bed position whole-body PET/CT imaging

Energy Technology Data Exchange (ETDEWEB)

Schatka, Imke [Hannover Medical School, Department of Nuclear Medicine, Hannover (Germany); Charite, Department of Nuclear Medicine, Berlin (Germany); Weiberg, Desiree; Reichelt, Stephanie; Owsianski-Hille, Nicole; Derlin, Thorsten; Berding, Georg; Bengel, Frank M. [Hannover Medical School, Department of Nuclear Medicine, Hannover (Germany)

2016-04-15

Continuous bed motion has recently been introduced for whole-body PET/CT, and represents a paradigm shift towards individualized and flexible acquisition without the limitations of bed position-based planning. Increased patient comfort due to lack of abrupt table position changes may be another albeit still unproven advantage. For robust clinical implementation, image quality and quantitative accuracy should at least be equal to the prior standard of bed position-based step-and-shoot imaging. The study included 68 consecutive patients referred for whole-body PET/CT for various malignancies. The patients underwent traditional step-and-shoot and novel continuous bed motion acquisition in the same session in a randomized crossover design. The patients and two independent observers were blinded to the sequence of scan techniques. Patient comfort/satisfaction was examined using a standardized questionnaire. SUVs were compared for reference tissue (liver, muscle) and tumour lesions. PET image quality and misalignment with CT images were evaluated on a scale of 1 - 4. Patients preferred continuous bed motion over step-and-shoot (P = 0.0001). It was considered to be more relaxing (38 % vs. 8 %), quieter (34 % vs. 8 %), and more fluid (64 % vs. 8 %). Image quality, SUV and CT misalignment did not differ between the techniques. Continuous bed motion resulted in better end-plane image quality (P < 0.0001). Regardless of the technique, second examinations had significantly higher tumour lesion SUVmax values (P = 0.0002), and a higher CT misalignment score (P = 0.0017). Oncological PET/CT with continuous bed motion enhances patient comfort and is associated with image quality at least comparable to that with traditional bed position-based step-and-shoot acquisition. (orig.)

Short communication: Dairy bedding type affects survival of Prototheca in vitro.

Science.gov (United States)

Adhikari, N; Bonaiuto, H E; Lichtenwalner, A B

2013-01-01

Protothecae are algal pathogens, capable of causing bovine mastitis, that are unresponsive to treatment; they are believed to have an environmental reservoir. The role of bedding management in control of protothecal mastitis has not been studied. The purpose of this study was to evaluate the growth of either environmental or mastitis-associated Prototheca genotypes in dairy bedding materials that are commonly used in Maine. Prototheca zopfii genotypes 1 and 2 (gt1 and gt2) were inoculated into sterile broth only (control ), kiln-dried spruce shavings, "green" hemlock sawdust, sand, or processed manure-pack beddings with broth, and incubated for 2 d. Fifty microliters of each isolate was then cultured onto plates and the resulting colonies counted at 24 and 48 h postinoculation. Shavings were associated with significantly less total Prototheca growth than other bedding types. Growth of P. zopfii gt1 was significantly higher than that of gt2 in the manure-pack bedding material. Spruce shavings, compared with manure, sand, or sawdust, may be a good bedding type to prevent growth of Prototheca. Based on these in vitro findings, bedding type may affect Prototheca infection of cattle in vivo. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Solid diffusion control of the adsorption of basic dyes onto granular activated carbon and natural zeolite in fixed bed columns

Directory of Open Access Journals (Sweden)

M. MARINKOVSKI

2001-07-01

Full Text Available The adsorption of basic dyes from aqueous solutions onto granular activated carbon and natural zeolite was studied using a fixed bed column. The design procedures for fixed bed adsorption columns were investigated for two basic dyes Maxilon Goldgelb GL EC 400 % (MG-400 and Maxilon Schwarz FBL-01 300 % (MS-300. A computer program based on the solid diffusion control model has been developed. The model parameters: solid diffusion coefficient, DS, axial dispersion coefficient, DL and external mass transfer coefficient, kf for all the investigated systems were estimated by means of a best fit approach.

In-situ determination of cross-over point for overcoming plasma-related matrix effects in inductively coupled plasma-atomic emission spectrometry

International Nuclear Information System (INIS)

Chan, George C.-Y.; Hieftje, Gary M.

2008-01-01

A novel method is described for overcoming plasma-related matrix effects in inductively coupled plasma-atomic emission spectrometry (ICP-AES). The method is based on measurement of the vertically resolved atomic emission of analyte within the plasma and therefore requires the addition of no reagents to the sample solution or to the plasma. Plasma-related matrix effects enhance analyte emission intensity low in the plasma but depress the same emission signal at higher positions. Such bipolar behavior is true for all emission lines and matrices that induce plasma-related interferences. The transition where the enhancement is balanced by the depression (the so-called cross-over point) results in a spatial region with no apparent matrix effects. Although it would be desirable always to perform determinations at this cross-over point, its location varies between analytes and from matrix to matrix, so it would have to be found separately for every analyte and for every sample. Here, a novel approach is developed for the in-situ determination of the location of this cross-over point. It was found that the location of the cross-over point is practically invariant for a particular analyte emission line when the concentration of the matrix was varied. As a result, it is possible to determine in-situ the location of the cross-over point for all analyte emission lines in a sample by means of a simple one-step sample dilution. When the original sample is diluted by a factor of 2 and the diluted sample is analyzed again, the extent of the matrix effect is identical (zero) between the original sample and the diluted sample at one and only one location - the cross-over point. This novel method was verified with several single-element matrices (0.05 M Na, Ca, Ba and La) and some mixed-element matrices (mixtures of Na-Ca, Ca-Ba, and a plant-sample digest). The inaccuracy in emission intensity due to the matrix effect could be as large as - 30% for conventional measurements in the

Fish oil-supplementation increases appetite in healthy adults. A randomized controlled cross-over trial.

Science.gov (United States)

Damsbo-Svendsen, Signe; Rønsholdt, Mia Dybkjær; Lauritzen, Lotte

2013-07-01

Marine n-3 fatty acids are hypothesized to have beneficial effects on obesity and cancer cachexia possibly via an effect on appetite. The aim of this study was to investigate, if fish oil-supplementation affects appetite in healthy individuals. In a randomized cross-over study, 20 normal-weight subjects (50% females) were given ten 0.5-mL capsules/day of fish oil or soybean oil for 3 weeks separated by 1-week wash-out. In the end of each period, appetite was assessed by 10-cm visual analog scales immediately before and after a standardized breakfast. Results were analyzed in accordance with the paired design considering oil sequence and gender. All subjects completed both periods with a compliance of 96% and oil sequence did not affect the results. There was no difference between the two supplements in any pre-breakfast appetite scores, but the post-prandial sensation of being full was 1.21 cm (0.20; 2.22) lower after the fish oil-period. Furthermore, there was a supplement × gender-interaction on "desire to eat more" due to a score increase of 1.09 cm (0.28; 1.90) in women only. These results suggest that marine n-3 fatty acid may increase appetite. This finding would be potentially beneficial for patients with compromised nutritional status. Copyright © 2013 Elsevier Ltd. All rights reserved.

"To sleep, perchance to tweet": in-bed electronic social media use and its associations with insomnia, daytime sleepiness, mood, and sleep duration in adults.

Science.gov (United States)

Bhat, Sushanth; Pinto-Zipp, Genevieve; Upadhyay, Hinesh; Polos, Peter G

2018-04-01

The use of mobile device-based electronic social media (ESM) in bed is rapidly becoming commonplace, with potentially adverse impacts on sleep and daytime functioning. The purpose of this study was to determine the extent to which in-bed ESM use is associated with insomnia, daytime sleepiness, mood, and sleep duration in adults. This was a cross-sectional observational study conducted among 855 hospital employees and university students (mean age, 43.6years; 85% female) via an online questionnaire. Nearly 70% of participants indulged in in-bed ESM use, with nearly 15% spending an hour or more a night doing so. The degree of in-bed ESM use did not vary by gender, but higher levels of in-bed ESM use were seen in younger and middle-aged than elderly participants. Compared with participants with no in-bed ESM use and controlling for age, gender, and ethnicity, participants with high in-bed ESM use were more likely to have insomnia, anxiety, and short sleep duration on weeknights, but not depression or daytime sleepiness; low in-bed ESM use only increased the likelihood of short sleep duration on weeknights. In-bed ESM use by a bed partner did not have an adverse association with sleep or mood. In-bed ESM use is associated with sleep and mood dysfunction in adults. These findings are of relevance to clinicians, therapists, and the public at large, as they suggest that limitation of in-bed ESM use is a potential interventional strategy in the overall management of sleep hygiene and mental health. Copyright © 2017 National Sleep Foundation. Published by Elsevier Inc. All rights reserved.

Pipeline corridors through wetlands -- Impacts on plant communities: Little Timber Creek Crossing, Gloucester County, New Jersey. Topical report, August 1991--January 1993

Energy Technology Data Exchange (ETDEWEB)

Shem, L.M.; Zimmerman, R.E.; Alsum, S.K. [Argonne National Lab., IL (United States). Center for Environmental Restoration Systems; Van Dyke, G.D. [Argonne National Lab., IL (United States). Center for Environmental Restoration Systems]|[Trinity Christian Coll., Palos Heights, IL (United States). Dept. of Biology

1994-12-01

The goal of the Gas Research Institute Wetland Corridors Program is to document impacts of existing pipelines on the wetlands they traverse. To accomplish this goal, 12 existing wetland crossings were surveyed. These sites varied in elapsed time since pipeline construction, wetland type, pipeline installation techniques, and right-of-way (ROW) management practices. This report presents results of a survey conducted over the period of August 5--7, 1991, at the Little Timber Creek crossing in Gloucester County, New Jersey, where three pipelines, constructed in 1950, 1960, and 1990, cross the creek and associated wetlands. The old side of the ROW, created by the installation of the 1960 pipeline, was designed to contain a raised peat bed over the 1950 pipeline and an open-water ditch over the 1960 pipeline. The new portion of the ROW, created by installation of the 1990 pipeline, has an open-water ditch over the pipeline (resulting from settling of the backfill) and a raised peat bed (resulting from rebound of compacted peat). Both the old and new ROWs contain dense stands of herbs; the vegetation on the old ROW was more similar to that in the adjacent natural area than was vegetation in the new ROW. The ROW increased species and habitat diversity in the wetlands. It may contribute to the spread of purple loosestrife and affect species sensitive to habitat fragmentation.

Pipeline corridors through wetlands -- Impacts on plant communities: Little Timber Creek Crossing, Gloucester County, New Jersey. Topical report, August 1991--January 1993

International Nuclear Information System (INIS)

Shem, L.M.; Zimmerman, R.E.; Alsum, S.K.; Van Dyke, G.D.; Trinity Christian Coll., Palos Heights, IL

1994-12-01

The goal of the Gas Research Institute Wetland Corridors Program is to document impacts of existing pipelines on the wetlands they traverse. To accomplish this goal, 12 existing wetland crossings were surveyed. These sites varied in elapsed time since pipeline construction, wetland type, pipeline installation techniques, and right-of-way (ROW) management practices. This report presents results of a survey conducted over the period of August 5--7, 1991, at the Little Timber Creek crossing in Gloucester County, New Jersey, where three pipelines, constructed in 1950, 1960, and 1990, cross the creek and associated wetlands. The old side of the ROW, created by the installation of the 1960 pipeline, was designed to contain a raised peat bed over the 1950 pipeline and an open-water ditch over the 1960 pipeline. The new portion of the ROW, created by installation of the 1990 pipeline, has an open-water ditch over the pipeline (resulting from settling of the backfill) and a raised peat bed (resulting from rebound of compacted peat). Both the old and new ROWs contain dense stands of herbs; the vegetation on the old ROW was more similar to that in the adjacent natural area than was vegetation in the new ROW. The ROW increased species and habitat diversity in the wetlands. It may contribute to the spread of purple loosestrife and affect species sensitive to habitat fragmentation

Integrated pyrolucite fluidized bed-membrane hybrid process for improved iron and manganese control in drinking water.

Science.gov (United States)

Dashtban Kenari, Seyedeh Laleh; Barbeau, Benoit

2017-04-15

Newly developed ceramic membrane technologies offer numerous advantages over the conventional polymeric membranes. This work proposes a new configuration, an integrated pyrolucite fluidized bed (PFB)-ceramic MF/UF hybrid process, for improved iron and manganese control in drinking water. A pilot-scale study was undertaken to evaluate the performance of this process with respect to iron and manganese control as well as membrane fouling. In addition, the fouling of commercially available ceramic membranes in conventional preoxidation-MF/UF process was compared with the hybrid process configuration. In this regard, a series of experiments were conducted under different influent water quality and operating conditions. Fouling mechanisms and reversibility were analyzed using blocking law and resistance-in-series models. The results evidenced that the flux rate and the concentration of calcium and humic acids in the feed water have a substantial impact on the filtration behavior of both membranes. The model for constant flux compressible cake formation well described the rise in transmembrane pressure. The compressibility of the filter cake substantially increased in the presence of 2 mg/L humic acids. The presence of calcium ions caused significant aggregation of manganese dioxide and humic acid which severely impacted the extent of membrane fouling. The PFB pretreatment properly alleviated membrane fouling by removing more than 75% and 95% of iron and manganese, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sodium/water pool-deposit bed model of the CONACS code

International Nuclear Information System (INIS)

Peak, R.D.

1983-01-01

A new Pool-Bed model of the CONACS (Containment Analysis Code System) code represents a major advance over the pool models of other containment analysis code (NABE code of France, CEDAN code of Japan and CACECO and CONTAIN codes of the United States). This new model advances pool-bed modeling because of the number of significant materials and processes which are included with appropriate rigor. This CONACS pool-bed model maintains material balances for eight chemical species (C, H 2 O, Na, NaH, Na 2 O, Na 2 O 2 , Na 2 CO 3 and NaOH) that collect in the stationary liquid pool on the floor and in the desposit bed on the elevated shelf of the standard CONACS analysis cell

Effect of a fermented dietary supplement containing chromium and zinc on metabolic control in patients with type 2 diabetes: a randomized, placebo-controlled, double-blind cross-over study

Directory of Open Access Journals (Sweden)

Yu-Mi Lee

2016-06-01

Full Text Available Background: For the increasing development of type 2 diabetes dietary habits play an important role. In this regard, dietary supplements are of growing interest to influence the progression of this disease. Objective: The aim of this study was to investigate the effect of a cascade-fermented dietary supplement based on fruits, nuts, and vegetables fortified with chromium and zinc on metabolic control in patients with type 2 diabetes mellitus. Methods: This was a randomized, placebo-controlled, double-blind, intervention study under free-living conditions using a cross-over design. Thirty-six patients with type 2 diabetes mellitus were enrolled and randomized either to receive a cascade-fermented dietary supplement enriched with chromium (100 µg/d and zinc (15 mg/d or a placebo similar in taste but without supplements, over a period of 12 weeks. After a wash-out period of 12 weeks, the patients received the other test product. The main outcome variable was the levels of glycated hemoglobin (HbA1c. Other outcome variables were fasting blood glucose, fructosamine, and lipid parameters. Results: Thirty-one patients completed the study. HbA1c showed no relevant changes during both treatment periods, nor was there a relevant difference between the two treatments (HbA1c: p=0.48. The same results were found for fructosamine and fasting glucose (fructosamine: p=0.9; fasting glucose: p=0.31. In addition, there was no effect on lipid metabolism. Conclusion: This intervention study does not provide evidence that a cascade-fermented plant-based dietary supplement enriched with a combination of chromium and zinc improves glucose metabolism in patients with type 2 diabetes mellitus under free-living conditions.

Time in bed, quality of sleep and school functioning of children.

Science.gov (United States)

Meijer, A M; Habekothé, H T; Van Den Wittenboer, G L

2000-06-01

This study describes the relationship of time in bed and quality of sleep with concentration and functioning at school. Neurotic and psychosomatic symptoms have been used as control variables. The sample consisted of 449 Dutch children in the seventh and eighth grades of elementary school. The age of the children varied between 9 y 5 mo and 14 y 5 mo. Seven schools participated in the research, with a total of 18 classes. The results indicated that 43% of the children had difficulty getting up in the morning. Furthermore, 15% of the children reported sleep problems and 25% did not feel rested at school. Time in bed and sleep quality show no relationship with concentration. Sleep quality, feeling rested at school and less distinct bedtimes were clearly related to school functioning. Another result was that children who had no difficulty getting up displayed more achievement motivation. Being open to the teacher's influence and achievement motivation depended mainly on sleep characteristics. Not getting bored at school, self-image as a pupil and control over aggressive behaviour were also influenced by gender, age, neuroticism and neurosomaticism.

Tracking channel bed resiliency in forested mountain catchments using high temporal resolution channel bed movement

Science.gov (United States)

Martin, Sarah E.; Conklin, Martha H.

2018-01-01

This study uses continuous-recording load cell pressure sensors in four, high-elevation (1500-1800 m), Sierra Nevada headwater streams to collect high-temporal-resolution, bedload-movement data for investigating the channel bed movement patterns within these streams for water years 2012-2014. Data show an annual pattern where channel bed material in the thalweg starts to build up in early fall, peaks around peak snow melt, and scours back to baseline levels during hydrograph drawdown and base flow. This pattern is punctuated by disturbance and recovery of channel bed material associated with short-term storm events. A conceptual model, linking sediment sources at the channel margins to patterns of channel bed fill and scour in the thalweg, is proposed building on the results of Martin et al. (2014). The material in the thalweg represents a balance between sediment supply from the channel margins and sporadic, conveyor-belt-like downstream transport in the thalweg. The conceptual model highlights not only the importance of production and transport rates but also that seasonal connectedness between the margins and thalweg is a key sediment control, determining the accumulation rate of sediment stores at the margins and the redistribution of sediment from margins to thalweg that feeds the conveyor belt. Disturbance and recovery cycles are observed at multiple temporal scales; but long term, the channel beds are stable, suggesting that the beds act as short-term storage for sediment but are in equilibrium interannually. The feasibility of use for these sensors in forested mountain stream environments is tested. Despite a high failure rate (50%), load cell pressure sensors show potential for high-temporal-resolution bedload measurements, allowing for the collection of channel bed movement data to move beyond time-integrated change measurements - where many of the subtleties of bedload movement patterns may be missed - to continuous and/or real-time measurements. This

Scour process caused by multiple subvertical non-crossing jets

Directory of Open Access Journals (Sweden)

Stefano Pagliara

2017-01-01

Full Text Available The scour process induced by plunging jets is an important topic for hydraulic engineers. In recent decades, several researchers have developed new strategies and methodologies to control the scour morphology, including different jet arrangements and structures located in the stilling basin. It has been found that multiple jets can cause less scouring than single plunging jets. Based on this evidence, this study aimed to investigate the equilibrium morphology caused by multiple non-crossing jets. A dedicated laboratory model was built and experimental tests were carried out under different combinations of jet inclination angles, by varying the tailwater level and the virtual crossing point location, which was set below the original channel bed level. It was experimentally shown that the equilibrium scour morphology depends on the jet discharge, the differences in non-crossing jet inclination angles, the downstream water level, and the distance of the virtual crossing point from the original channel bed level. In particular, the last parameter was found to be one of the most influential parameters, because of the resulting flow patterns inside the water body. Furthermore, the analysis of experimental evidence allowed for a complete and detailed classification of the scour hole typologies. Three different scour typologies were distinguished and classified. Finally, based on previous studies, two novel relationships have been proposed to predict both the maximum scour depth and length within a large range of hydraulic and geometric parameters.

Sampling interval analysis and CDF generation for grain-scale gravel bed topography

Science.gov (United States)

In river hydraulics, there is a continuing need for characterizing bed elevations to arrive at quantitative roughness measures that can be used in predicting flow depth and for improved prediction of fine-sediment transport over and through coarse beds. Recently published prediction methods require...

Skin maintenance in the bed-ridden patient.

Science.gov (United States)

Flam, E

1990-01-01

The skin of a patient at risk of developing pressure ulcers can resist deterioration if the conditions that weaken it are controlled. The purpose of this study is to determine the relationships between hydration level, skin temperature, and friction in patients at risk of development or reoccurrence of pressure ulcers and in patients with newly created surgical flaps. Two systems were considered: the standard hospital mattress covered with a thick occlusive plastic film and a 50/50 cotton/polyester bed sheet and the KinAir and the TheraPulse support systems with nylon/High Air Loss GORE-TEX (n/HAL) laminate cushions and coverlets. The moisture vapor management and aeration capabilities of the support system materials were determined, and the frictional force generated against the skin was measured. The results revealed that excessive hydration increases the level of friction against the skin while at the same time reducing the mechanical properties of the protective skin layers. The n/HAL laminate coverlet also had a significantly lower skin friction coefficient than the 50/50 cotton/polyester bed sheet. The significance of these findings is that over-hydration accelerates the abrading action on the skin by increasing the frictional force and decreasing the shear resistance of the skin.

Radionuclide transport in running waters, sensitivity analysis of bed-load, channel geometry and model discretisation

International Nuclear Information System (INIS)

Jonsson, Karin; Elert, Mark

2006-08-01

In this report, further investigations of the model concept for radionuclide transport in stream, developed in the SKB report TR-05-03 is presented. Especially three issues have been the focus of the model investigations. The first issue was to investigate the influence of assumed channel geometry on the simulation results. The second issue was to reconsider the applicability of the equation for the bed-load transport in the stream model, and finally the last issue was to investigate how the model discretisation will influence the simulation results. The simulations showed that there were relatively small differences in results when applying different cross-sections in the model. The inclusion of the exact shape of the cross-section in the model is therefore not crucial, however, if cross-sectional data exist, the overall shape of the cross-section should be used in the model formulation. This could e.g. be accomplished by using measured values of the stream width and depth in the middle of the stream and by assuming a triangular shape. The bed-load transport was in this study determined for different sediment characteristics which can be used as an order of magnitude estimation if no exact determinations of the bed-load are available. The difference in the calculated bed-load transport for the different materials was, however, found to be limited. The investigation of model discretisation showed that a fine model discretisation to account for numerical effects is probably not important for the performed simulations. However, it can be necessary for being able to account for different conditions along a stream. For example, the application of mean slopes instead of individual values in the different stream reaches can result in very different predicted concentrations

Cooling of a polyethylene tunnel type greenhouse by means of a rock bed

Energy Technology Data Exchange (ETDEWEB)

Kurklu, Ahmet; Bilgin, Sefai [Akdeniz Univ., Dept. of Agricultural Mechanisation, Antalya (Turkey)

2004-10-01

An experiment was conducted to cool a 15 m{sup 2} ground area plastic-tunnel-type greenhouse by the use of a rock bed. An identical greenhouse with no rock bed was also erected for control purposes. Two rock-bed canals, each with the dimensions of 3 x l.25 x 0.75 m, were dug in the soil of the experimental greenhouse. After the canals were filled with the rocks and insulated, the top surface was covered by a soil layer of thickness enough for the root development depth of the plants. Air was pushed through the rock bed by a centrifugal fan with a 1100 m{sup 3}/h flow rate. Energy stored in the rock bed during the day was dumped outside the greenhouse at night using the cooler outside air. The results of the measurements showed that the rock-bed system maintained air temperature 14 deg C lower at maximum in the experimental greenhouse than the control one. The temperature difference seemed to increase with increasing solar radiation and outside air temperature. Relative humidity during the day remained at about 40% in the experimental greenhouse and was always higher than that in the control one. The coefficient of performance (COP) of the rock-bed system was higher than 3 in general, and it was observed that this value increased with decreasing rock-bed temperature. The average solar collection efficiency was 38%. The rock-bed system seems to have a significant potential for cooling applications in greenhouses. (Author)

Thermalhydraulics of flowing particle-bed-type fusion reactor blankets

International Nuclear Information System (INIS)

Nietert, R.E.; Abdelk-Khalik, S.I.

1982-01-01

An experimental investigation has been conducted to determine the heat transfer characteristics of gravity-flowing particle beds using a special heat transfer loop. Glass microspheres were allowed to flow by gravity at controlled rates through an electrically heated stainless steel tubular test section. Values of the local and average convective heat transfer coefficient as a function of the average bed velocity, particle size and heat flux were determined. Such information is necessary for the design of gravity-flowing particle-bed type fusion reactor-blankets and associated tritium recovery systems. (orig.)

A new process control strategy for aqueous film coating of pellets in fluidised bed

DEFF Research Database (Denmark)

Larsen, C.C.; Sonnergaard, Jørn; Bertelsen, Pernille Scholdan

2003-01-01

The parameters with effect on maximum spray rate and maximum relative outlet air humidity when coating pellets in a fluidised bed were investigated. The tested variables include type of water based modified release film coating (Eudragit® NE 30D, Eudragit® RS 30D, Aquacoat ECD®) coating principle...... (top spray, bottom spray), inlet air humidity and type of pellets (sugar spheres, microcrystalline cellulose pellets). The maximum spray rate was not influenced by the coating principles. The highest spray rate was obtained for the film polymer with the lowest tackiness which is assumed...... to be the controlling factor. The type of pellets affected the maximum spray rate. A thermodynamic model for the coating process is employed throughout the process and not just during steady state. The thermodynamic model is incorporated into a new process control strategy. The process control strategy is based on in...

Evaluation of free-stall mattress bedding treatments to reduce mastitis bacterial growth

Energy Technology Data Exchange (ETDEWEB)

Kristula, M A; Dou, Z; Toth, J D; Smith, B I; Harvey, N; Sabo, M [University of Penn, Kennett Square, PA (United States)

2008-05-15

Bacterial counts were compared in free-stall mattresses and teat ends exposed to 5 treatments in a factorial study design on 1 dairy farm. Mattresses in five 30-cow groups were subjected to 1 of 5 bedding treatments every other day: 0.5 kg of hydrated limestone, 120 mL of commercial acidic conditioner, 1 kg of coal fly ash, 1 kg of kiln-dried wood shavings, and control (no bedding). Counts of coliforms, Klebsiella spp., Escherichia coli, and Streptococcus spp. were lowest on mattresses bedded with lime. Mattresses bedded with the commercial acidic conditioner had the next lowest counts for coliforms, Klebsiella spp., and Streptococcus spp. Wood shavings and the no-bedding control had the highest counts for coliform and Klebsiella spp. Compared with wood shavings or control, fly ash reduced the counts of coliforms, whereas for the other 3 bacterial groups, the reduction was not always significant. Streptococcus spp. counts were greatest in the control group and did not differ among the shavings and fly ash groups. Teat swab results indicated that hydrated lime was the only bedding treatment that significantly decreased the counts of both coliforms and Klebsiella spp. There were no differences in Streptococcus spp. numbers on the teats between any of the bedding treatments. Bacterial populations grew steadily on mattresses and were generally higher at 36 to 48 h than at 12 to 24 h, whereas bacterial populations on teats grew rapidly by 12 h and then remained constant. Hydrated lime was the only treatment that significantly reduced bacterial counts on both mattresses and teat ends, but it caused some skin irritation.

Assessing the Importance of Cross-Stream Transport in Bedload Flux Estimates from Migrating Dunes: Colorado River, Grand Canyon National Park

Science.gov (United States)

Leary, K. P.; Buscombe, D.; Schmeeckle, M.; Kaplinski, M. A.

2017-12-01

Bedforms are ubiquitous in sand-bedded rivers, and understanding their morphodynamics is key to quantifying bedload transport. As such, mechanistic understanding of the spatiotemporal details of sand transport through and over bedforms is paramount to quantifying total sediment flux in sand-bedded river systems. However, due to the complexity of bedform field geometries and migration in natural settings, our ability to relate migration to bedload flux, and to quantify the relative role of tractive and suspended processes in their dynamics, is incomplete. Recent flume and numerical investigations indicate the potential importance of cross-stream transport, a process previously regarded as secondary and diffusive, to the three-dimensionality of bedforms and spatially variable translation and deformation rates. This research seeks to understand and quantify the importance of cross-stream transport in bedform three-dimensionality in a field setting. This work utilizes a high-resolution (0.25 m grid) data set of bedforms migrating in the channel of the Colorado River in Grand Canyon National Park. This data set comprises multi-beam sonar surveys collected at 3 different flow discharges ( 283, 566, and 1076 m3/s) along a reach of the Colorado River just upstream of the Diamond Creek USGS gage. Data were collected every 6 minutes almost continuously for 12 hours. Using bed elevation profiles (BEPs), we extract detailed bedform geometrical data (i.e. bedform height, wavelength) and spatial sediment flux data over a suite of bedforms at each flow. Coupling this spatially extensive data with a generalized Exner equation, we conduct mass balance calculations that evaluate the possibility, and potential importance, of cross-stream transport in the spatial variability of translation and deformation rates. Preliminary results suggest that intra-dune cross-stream transport can partially account for changes in the planform shape of dunes and may play an important role in spatially

The impact of structural development on near bed flow dynamics in gravel bed rivers: coupling flume experiments with numerical modelling

Science.gov (United States)

Ockelford, A.; Hardy, R. J.; Rice, S. P.; Powell, M.

2017-12-01

It is increasingly being recognised that gravel bed rivers develop a surface `texture' in response to changes in the flow and sediment regime. This textural response often takes the form of a bed structure which develops to ultimately stabilise the surface across a range of spatio-temporal scales and it is these topographical structures which determine the flow structures that develop over the river bed. However, our ability to measure and parameterise that structure in ways that are useful and meaningful for the prediction of flow dynamics, still remains inadequate; this paper uses a three dimensional numerical model to assess how the temporal development of structure influences the near bed flow dynamics. Using a suite of flume based experiments a unimodal grain size distribution (σg = 1.30, D50 = 8.8mm) was exposed to three different levels of constant bed shear that produced sediment transport conditions ranging from marginal transport to conditions approaching full mobility of all size fractions. Surface structuring characteristics were measured at a high spatio-temporal resolution such that the time evolution of the beds could be fully described. In total 54 surfaces were generated and run through a Reynolds averaged three dimensional numerical model with an Rng turbulence closure. The topography input included using an immersed boundary technique within a Cartesian framework. Discussion concentrates on the how the trajectory of structural evolution under the different treatments affects the near bed flow dynamics. Specifically links are made between how the scales of boundary topography influence the flow and discusses how the measured flow variability at any one point will contain both locally derived and upstream-inherited flow structures, according to the range of scales of bed topography present. Keywords: Graded, Sediment, Structure, Turbulence, Modelling

Quench cooling of superheated debris beds in containment during LWR core meltdown accidents

International Nuclear Information System (INIS)

Ginsberg, T.; Chen, J.C.

1984-01-01

Light water reactor core meltdown accident sequence studies suggest that superheated debris beds may settle on the concrete floor beneath the reactor vessel. A model for the heat transfer processes during quench of superheated debris beds cooled by an overlying pool of water has been presented in a prior paper. This paper discusses the coolability of decay-heated debris beds from the standpoint of their transient quench characteristics. It is shown that even though a debris bed configuration may be coolable from the point of view of steady-state decay heat removal, the quench behavior from an initially elevated temperature may lead to bed melting prior to quench of the debris

An adaptable, low cost test-bed for unmanned vehicle systems research

Science.gov (United States)

Goppert, James M.

2011-12-01

An unmanned vehicle systems test-bed has been developed. The test-bed has been designed to accommodate hardware changes and various vehicle types and algorithms. The creation of this test-bed allows research teams to focus on algorithm development and employ a common well-tested experimental framework. The ArduPilotOne autopilot was developed to provide the necessary level of abstraction for multiple vehicle types. The autopilot was also designed to be highly integrated with the Mavlink protocol for Micro Air Vehicle (MAV) communication. Mavlink is the native protocol for QGroundControl, a MAV ground control program. Features were added to QGroundControl to accommodate outdoor usage. Next, the Mavsim toolbox was developed for Scicoslab to allow hardware-in-the-loop testing, control design and analysis, and estimation algorithm testing and verification. In order to obtain linear models of aircraft dynamics, the JSBSim flight dynamics engine was extended to use a probabilistic Nelder-Mead simplex method. The JSBSim aircraft dynamics were compared with wind-tunnel data collected. Finally, a structured methodology for successive loop closure control design is proposed. This methodology is demonstrated along with the rest of the test-bed tools on a quadrotor, a fixed wing RC plane, and a ground vehicle. Test results for the ground vehicle are presented.

Artificial intelligence-based modeling and control of fluidized bed combustion

Energy Technology Data Exchange (ETDEWEB)

Ikonen, E.; Leppaekoski, K. (Univ. of Oulu, Dept. of Process and Environmental Engineering (Finland)). email: enso.ikonen@oulu.fi

2009-07-01

AI-inspired techniques have a lot to offer when developing methods for advanced identification, monitoring, control and optimization of industrial processes, such as power plants. Advanced control methods have been extensively examined in the research of the Power Plant Automation group at the Systems Engineering Laboratory, e.g., in fuel inventory modelling, combustion power control, modelling and control of flue gas oxygen, drum control, modelling and control of superheaters, or in optimization of flue-gas emissions. Most engineering approaches to artificial intelligence (AI) are characterized by two fundamental properties: the ability to learn from various sources and the ability to deal with plant complexity. Learning systems that are able to operate in uncertain environments based on incomplete information are commonly referred to as being intelligent. A number of other approaches exist, characterized by these properties, but not easily categorized as AI-systems. Advanced control methods (adaptive, predictive, multivariable, robust, etc.) are based on the availability of a model of the process to be controlled. Hence identification of processes becomes a key issue, leading to the use of adaptation and learning techniques. A typical learning control system concerns a selection of learning techniques applied for updating a process model, which in turn is used for the controller design. When design of learning control systems is complemented with concerns for dealing with uncertainties or vaguenesses in models, measurements, or even objectives, particularly close connections exist between advanced process control and methods of artificial intelligence and machine learning. Needs for advanced techniques are typically characterized by the desire to properly handle plant non-linearities, the multivariable nature of the dynamic problems, and the necessity to adapt to changing plant conditions. In the field of fluidized bed combustion (FBC) control, the many promising

Comparison of chest compressions in the standing position beside a bed at knee level and the kneeling position: a non-randomised, single-blind, cross-over trial.

Science.gov (United States)

Oh, Je Hyeok; Kim, Chan Woong; Kim, Sung Eun; Lee, Sang Jin; Lee, Dong Hoon

2014-07-01

When rescuers perform cardiopulmonary resuscitation (CPR) from a standing position, the height at which chest compressions are carried out is raised. To determine whether chest compressions delivered on a bed adjusted to rescuer's knee height are as effective as those delivered on the floor. A total of 20 fourth-year medical students participated in the study. The students performed chest compressions for 2 min each on a manikin lying on the floor (test 1) and on a manikin lying on a bed (test 2). The average compression rate (ACR) and the average compression depth (ACD) were compared between the two tests. The ACR was not significantly different between tests 1 and 2 (120.1 to 132.9  vs 115.7 to 131.2 numbers/min, 95% CI, p=0.324). The ACD was also not significantly different between tests 1 and 2 (51.2 to 56.6 vs 49.4 to 55.7 mm, 95% CI, p=0.058). The results suggest that there may be no significant differences in compression rate and depth between CPR performed on manikins placed on the floor and those placed at a rescuer's knee height. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Light extinction in metallic powder beds: Correlation with powder structure

International Nuclear Information System (INIS)

Rombouts, M.; Froyen, L.; Gusarov, A.V.; Bentefour, E.H.; Glorieux, C.

2005-01-01

A theoretical correlation between the effective extinction coefficient, the specific surface area, and the chord length distribution of powder beds is verified experimentally. The investigated powder beds consist of metallic particles of several tens of microns. The effective extinction coefficients are measured by a light-transmission technique at a wavelength of 540 nm. The powder structure is characterized by a quantitative image analysis of powder bed cross sections resulting in two-point correlation functions and chord length distributions. The specific surface area of the powders is estimated by laser-diffraction particle-size analysis and by the two-point correlation function. The theoretically predicted tendency of increasing extinction coefficient with specific surface area per unit void volume is confirmed by the experiments. However, a significant quantitative discrepancy is found for several powders. No clear correlation of the extinction coefficient with the powder material and particle size, and morphology is revealed, which is in line with the assumption of geometrical optics

Effect of interprofessional student-led beds on emergency department performance indicators.

Science.gov (United States)

Meek, Robert; Morphet, Julia; Hood, Kerry; Leech, Michelle; Sandry, Kate

2013-10-01

The study aims to compare ED performance indicators between patients managed by students in an inter-professional learning (IPL) programme and comparable patients receiving usual ED care. An IPL programme ran for five separate 2 week periods during 2012. Four student-led beds were managed by four final year students (two medical, two nursing). Four control beds were matched for patient acuity. Data were gathered electronically from the ED information system. Comparisons of baseline characteristics and a range of ED performance indicators were made between patients managed in the student-led and control beds. Patient satisfaction with student care was surveyed. Characteristics of the 369 study and 365 control patients were similar. Median times to being seen by a nurse and a doctor were not significantly different between student-led and control beds, at 50 (19-103) versus 45 (20-93) min, and 84 (28-162) versus 91 (41-165) min, respectively. Median time to inpatient referral for admitted patients was significantly longer in student-led compared with control beds, being 142 (65-249) versus 101.5 (48-200) min, respectively. Median lengths of stay were similar between the student-led and control groups, being 263 (201-343) versus 303.5 (204-384) min for discharged patients, and 866 (571-1238) versus 745.5 (487-1168) min for inpatient ward admissions. Patients reported high levels of satisfaction with student care. There was little difference in performance indicators between patients managed by student teams as part of an IPL programme and a similar group receiving usual ED care. © 2013 Australasian College for Emergency Medicine and Australasian Society for Emergency Medicine.

Styrene biofiltration in a trickle-bed reactor

Directory of Open Access Journals (Sweden)

V. Novak

2008-04-01

Full Text Available The biological treatment of styrene waste gas in a trickle-bed filter (TBF was investigated. The bioreactor consisted of a two-part glass cylinder (ID 150 mm filled with 25 mm polypropylene Pall rings serving as packing material. The bed height was 1m. Although the laboratory temperature was maintained at 22 ºC, the water temperature in the trickle-bed filter was slightly lower (about 18 ºC.The main aim of our study was to observe the effect of empty-bed residence time (EBRT on bioreactor performance at a constant pollutant concentration over an extended time period. The bioreactor was inoculated with a mixed microbial consortium isolated from a styrene-degrading biofilter that had been running for the previous two years. After three weeks of acclimation period, the bioreactor was loaded with styrene (100 mg.m-3. EBRT was in the range of 53 s to 13 s. A maximum elimination capacity (EC of 11.3 gC.m-3.h-1 was reached at an organic loading (OL rate of 18.6 gC.m-3.h-1.

Influence of decelerating flow on incipient motion of a gravel-bed ...

Indian Academy of Sciences (India)

2016-08-26

Aug 26, 2016 ... From the observation of eleven fixed-bed and nine mobile-bed velocity profiles, it is revealed that the parabolic law method (PLM) and the Reynolds stress method are comparable for estimation of shear velocity in general. Also, the results show that the shear stress distribution adopts a convex form over ...

Preliminary assessment of channel stability and bed-material transport in the Tillamook Bay tributaries and Nehalem River basin, northwestern Oregon

Science.gov (United States)

Jones, Krista L.; Keith, Mackenzie K.; O'Connor, Jim E.; Mangano, Joseph F.; Wallick, J. Rose

2012-01-01

valley confinement. * Natural and human-caused disturbances such as mass movements, logging, fire, channel modifications for navigation and flood control, and gravel mining also have varying effects on channel condition, bed-material transport, and distribution and area of bars throughout the study areas and over time. * Existing datasets include at least 16 and 18 sets of aerial and orthophotographs that were taken of the study areas in the Tillamook Bay tributary basins and Nehalem River basin, respectively, from 1939 to 2011. These photographs are available for future assessments of long-term changes in channel condition, bar area, and vegetation establishment patterns. High resolution Light Detection And Ranging (LiDAR) surveys acquired in 2007-2009 could support future quantitative analyses of channel morphology and bed-material transport in all study areas. * A review of deposited and mined gravel volumes reported for instream gravel mining sites shows that bed-material deposition tends to rebuild mined bar surfaces in most years. Mean annual deposition volumes on individual bars exceeded 3,000 cubic meters (m3) on Donaldson Bar on the Wilson River, Dill Bar on the Kilchis River, and Plant and Winslow Bars on the Nehalem River. Cumulative reported volumes of bed-material deposition were greatest at Donaldson and Dill Bars, totaling over 25,000 m3 per site from 2004 to 2011. Within this period, reported cumulative mined volumes were greatest for the Donaldson, Plant, and Winslow Bars, ranging from 24,470 to 33,940 m3. * Analysis of historical stage-streamflow data collected by the U.S. Geological Survey on the Wilson River near Tillamook (14301500) and Nehalem River near Foss (14301000) shows that these rivers have episodically aggraded and incised, mostly following high flow events, but they do not exhibit systematic, long-term trends in bed elevation. * Multiple cross sections show that channels near bridge crossings in all six study areas are dynamic with many

The effect of hydraulic bed movement on the quality of chest compressions.

Science.gov (United States)

Park, Maeng Real; Lee, Dae Sup; In Kim, Yong; Ryu, Ji Ho; Cho, Young Mo; Kim, Hyung Bin; Yeom, Seok Ran; Min, Mun Ki

2017-08-01

The hydraulic height control systems of hospital beds provide convenience and shock absorption. However, movements in a hydraulic bed may reduce the effectiveness of chest compressions. This study investigated the effects of hydraulic bed movement on chest compressions. Twenty-eight participants were recruited for this study. All participants performed chest compressions for 2min on a manikin and three surfaces: the floor (Day 1), a firm plywood bed (Day 2), and a hydraulic bed (Day 3). We considered 28 participants of Day 1 as control and each 28 participants of Day 2 and Day 3 as study subjects. The compression rates, depths, and good compression ratios (>5-cm compressions/all compressions) were compared between the three surfaces. When we compared the three surfaces, we did not detect a significant difference in the speed of chest compressions (p=0.582). However, significantly lower values were observed on the hydraulic bed in terms of compression depth (p=0.001) and the good compression ratio (p=0.003) compared to floor compressions. When we compared the plywood and hydraulic beds, we did not detect significant differences in compression depth (p=0.351) and the good compression ratio (p=0.391). These results indicate that the movements in our hydraulic bed were associated with a non-statistically significant trend towards lower-quality chest compressions. Copyright © 2017 Elsevier Inc. All rights reserved.

Realisation of a gamma emission tomograph by a servo-controlled camera and bed

International Nuclear Information System (INIS)

Guzman-Torres, D.R.

1980-07-01

We took part in the building of a transverse axial emission tomograph intended for nuclear medicine. The following three points were dealt with: mathematical, choice of processing algorithm; electronic, development of equipment; experimental, testing of the system built. On the mathematical side, following a survey of reconstruction methods, we studied the use of a reconstruction algorithm after filtering of the projections by convolution which gives a good spatial resolution. We also proposed a means to solve the computing time/quality of image problem, leading to a satisfactory result within a shorter total investigation time. In this way the computing time has been reduced by a factor three. In the electronics field we built an interface between the bed, the gamma camera and the computer already in the laboratory. The present instrument corresponds to version no. 2. The system control the bed and gamma camera which are operated from the computer. Experimentally we were able on checking the calculations with a phantom made up of small emitting sources, to prove by finding the exact spot our ability to locate active foci on the patient. While the results obtained are encouraging from the image restitution viewpoint, the study of problems related to self-absorption inside the organ and those of statistical noise have still to be continued [fr

Analysis of the Internal Bed Regulation Committees from hospitals of a Southern Brazilian city

Science.gov (United States)

Soares, Vinícius Sabedot

2017-01-01

ABSTRACT Objective To evaluate the composition of the Internal Regulation Committees created in hospitals of a capital city. Methods A cross-sectional descriptive study assessing the structure, processes and results of each Committee. Results The main reasons for implementing the committees were legal issues and overcrowding in the emergency department. The most monitored indicators were the occupancy rate and the mean length of stay, and the most observed results were reductions in the latter. Institutional protocols were developed in 70% of cases, and the degree of support that the Internal Regulation Committee received from the hospital managers was high, despite being only average the support received from the medical teams. Promoting the efficient use of beds seemed to be the main goal. To achieve it, the Internal Regulation Committee had to control hospital capacity at levels that allowed proper and safe bed turnover for patients. The strategies for this were varied and needed to integrate administrative and care issues. Conclusion The Internal Regulation Committees were a management tool with great potential and promising results in the experiences evaluated. PMID:29091157

Understanding and modeling retention of mammalian cells in fluidized bed centrifuges.

Science.gov (United States)

Kelly, William; Rubin, Jonathan; Scully, Jennifer; Kamaraju, Hari; Wnukowski, Piotr; Bhatia, Ravinder

2016-11-01

Within the last decade, fully disposable centrifuge technologies, fluidized-bed centrifuges (FBC), have been introduced to the biologics industry. The FBC has found a niche in cell therapy where it is used to collect, concentrate, and then wash mammalian cell product while continuously discarding centrate. The goal of this research was to determine optimum FBC conditions for recovery of live cells, and to develop a mathematical model that can assist with process scaleup. Cell losses can occur during bed formation via flow channels within the bed. Experimental results with the kSep400 centrifuge indicate that, for a given volume processed: the bed height (a bed compactness indicator) is affected by RPM and flowrate, and dead cells are selectively removed during operation. To explain these results, two modeling approaches were used: (i) equating the centrifugal and inertial forces on the cells (i.e., a force balance model or FBM) and (ii) a two-phase computational fluid dynamics (CFD) model to predict liquid flow patterns and cell retention in the bowl. Both models predicted bed height vs. time reasonably well, though the CFD model proved more accurate. The flow patterns predicted by CFD indicate a Coriolis-driven flow that enhances uniformity of cells in the bed and may lead to cell losses in the outflow over time. The CFD-predicted loss of viable cells and selective removal of the dead cells generally agreed with experimental trends, but did over-predict dead cell loss by up to 3-fold for some of the conditions. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:1520-1530, 2016. © 2016 American Institute of Chemical Engineers.

The effect of small solar powered 'Bͻkͻͻ' net fans on mosquito net use: results from a randomized controlled cross-over trial in southern Ghana.

Science.gov (United States)

Briët, Olivier J T; Yukich, Joshua O; Pfeiffer, Constanze; Miller, William; Jaeger, Mulako S; Khanna, Nitin; Oppong, Samuel; Nardini, Peter; Ahorlu, Collins K; Keating, Joseph

2017-01-03

Long-lasting insecticidal nets (LLINs) are ineffective malaria transmission prevention tools if they are unused. Discomfort due to heat is the most commonly reported reason for not using nets, but this problem is largely unaddressed. With increasing rural electrification and the dropping price of solar power, fans could improve comfort inside nets and be affordable to populations in malaria endemic areas. Here, results are presented from a pilot randomized controlled cross-over study testing the effect of fans on LLIN use. Eighty-three households from two rural communities in Greater Accra, Ghana, randomized into three groups, participated in a 10-month cross-over trial. After a screening survey to identify eligible households, all households received new LLINs. Bͻkͻͻ net fan systems (one fan per member) were given to households in Group 1 and water filters were given to households in Group 2. At mid-point, Group 1 and 2 crossed over interventions. Households in Group 1 and 2 participated in fortnightly surveys on households' practices related to nets, fans and water filters, while households in Group 3 were surveyed only at screening, mid-point and study end. Entomological and weather data were collected throughout the study. Analysis took both 'per protocol' (PP) and 'intention to treat' (ITT) approaches. The mid- and end-point survey data from Group 1 and 2 were analysed using Firth logistic regressions. Fortnightly survey data from all groups were analysed using logistic regressions with random effects. Provision of fans to households appeared to increase net use in this study. Although the increase in net use explained by fans was not significant in the primary analyses (ITT odds ratio 3.24, p > 0.01; PP odds ratio = 1.17, p > 0.01), it was significant in secondary PP analysis (odds ratio = 1.95, p Fan use was 90-100% depending on the fortnightly visit. This pilot study could not provide definitive evidence that fans increase net use. A larger

Controlled biomass formation and kinetics of toluene degradation in a bioscrubber and in a reactor with a periodically moved trickle-bed.

Science.gov (United States)

Wübker, S M; Laurenzis, A; Werner, U; Friedrich, C

1997-08-20

The kinetics of degradation of toluene from a model waste gas and of biomass formation were examined in a bioscrubber operated under different nutrient limitations with a mixed culture. The applicability of the kinetics of continuous cultivation of the mixed culture was examined for a special trickle-bed reactor with a periodically moved filter bed. The efficiency of toluene elimination of the bioscrubber was 50 to 57% and depended on the toluene mass transfer as evident from a constant productivity of 0.026 g dry cell weight/L . h over the dilution rate. Under potassium limitation the biomass productivity was reduced by 60% to 0.011 g dry cell weight/L . h at a dilution rate of 0.013/h. Conversely, at low dilution rates the specific toluene degradation rates increased. Excess biomass in a trickle-bed reactor causes reduction of interfacial area and mass transfer, and increase in pressure drop. To avoid these disadvantages, the trickle-bed was moved periodically and biomass was removed with outflowing medium. The concentration of steady state biomass fixed on polyamide beads decreased hyperbolically with the dilution rate. Also, the efficiency of toluene degradation decreased from 72 to 56% with increasing dilution rate while the productivity increased. Potassium limitation generally caused a reduction in biomass, productivity, and yield while the specific degradation increased with dilution rate. This allowed the application of the principles of the chemostat to the trickle-bed reactor described here, for toluene degradation from waste gases. (c) 1997 John Wiley & Sons, Inc. Biotechnol Bioeng 55: 686-692, 1997.

Management bedding : vrijloopstal met composterende bedding van houtsnippers

NARCIS (Netherlands)

Boer, de H.C.; Wiersma, M.; Galama, P.J.; Szanto, G.L.

2015-01-01

In de vrijloopstal liggen de koeien meestal op een organische bedding en scheiden daar mest (feces en urine) uit. Om de bedding voldoende droog en schoon te houden wordt er regelmatig nieuw strooisel aangevoerd en wordt de toplaag bewerkt. Op basis van onderzoek- en praktijkervaringen tot nu toe

Bed-material entrainment potential, Roaring Fork River at Basalt, Colorado

Science.gov (United States)

Elliott, John G.

2002-01-01

The Roaring Fork River at Basalt, Colorado, has a frequently mobile streambed composed of gravel, cobbles, and boulders. Recent urban and highway development on the flood plain, earlier attempts to realign and confine the channel, and flow obstructions such as bridge openings and piers have altered the hydrology, hydraulics, sediment transport, and sediment deposition areas of the Roaring Fork. Entrainment and deposition of coarse sediment on the streambed and in large alluvial bars have reduced the flood-conveying capacity of the river. Previous engineering studies have identified flood-prone areas and hazards related to inundation and high streamflow velocity, but those studies have not evaluated the potential response of the channel to discharges that entrain the coarse streambed. This study builds upon the results of earlier flood studies and identifies some potential areas of concern associated with bed-material entrainment. Cross-section surveys and simulated water-surface elevations from a previously run HEC?RAS model were used to calculate the boundary shear stress on the mean streambed, in the thalweg, and on the tops of adjacent alluvial bars for four reference streamflows. Sediment-size characteristics were determined for surficial material on the streambed, on large alluvial bars, and on a streambank. The median particle size (d50) for the streambed samples was 165 millimeters and for the alluvial bars and bank samples was 107 millimeters. Shear stresses generated by the 10-, 50-, and 100-year floods, and by a more common flow that just inundated most of the alluvial bars in the study reach were calculated at 14 of the cross sections used in the Roaring Fork River HEC?RAS model. The Shields equation was used with a Shields parameter of 0.030 to estimate the critical shear stress for entrainment of the median sediment particle size on the mean streambed, in the thalweg, and on adjacent alluvial bar surfaces at the 14 cross sections. Sediment

Cross-layer restoration with software defined networking based on IP over optical transport networks

Science.gov (United States)

Yang, Hui; Cheng, Lei; Deng, Junni; Zhao, Yongli; Zhang, Jie; Lee, Young

2015-10-01

The IP over optical transport network is a very promising networking architecture applied to the interconnection of geographically distributed data centers due to the performance guarantee of low delay, huge bandwidth and high reliability at a low cost. It can enable efficient resource utilization and support heterogeneous bandwidth demands in highly-available, cost-effective and energy-effective manner. In case of cross-layer link failure, to ensure a high-level quality of service (QoS) for user request after the failure becomes a research focus. In this paper, we propose a novel cross-layer restoration scheme for data center services with software defined networking based on IP over optical network. The cross-layer restoration scheme can enable joint optimization of IP network and optical network resources, and enhance the data center service restoration responsiveness to the dynamic end-to-end service demands. We quantitatively evaluate the feasibility and performances through the simulation under heavy traffic load scenario in terms of path blocking probability and path restoration latency. Numeric results show that the cross-layer restoration scheme improves the recovery success rate and minimizes the overall recovery time.

Online process control of a pharmaceutical intermediate in a fluidized-bed drier environment using near-infrared spectroscopy.

Science.gov (United States)

Märk, Julia; Karner, Martin; Andre, Max; Rueland, Jochen; Huck, Christian W

2010-05-15

In the production plant of an antibiotic substance, a new fluidized-bed drier has been installed. For online process control of the drying progress and determination of the ideal drying end point, a continuous near-infrared spectroscopic (NIRS) measuring setup was implemented to rapidly and simultaneously gain all essential product information. A bypass system outside the drier combined with a robust process probe proved to provide the best sampling system geometry. The spectrometer was equipped with an additional laboratory probe for complementary offline analysis. Multivariate calibrations for product assay, water content, and residual solvent were calculated, optimized, and compared for the two probes. The final root-mean-square error of cross validation (RMSECV) for the process probe could be reduced to 0.81% for the product assay, 0.25% for water, and 0.06% for acetone. The laboratory-probe prediction values show good agreement with reference data during the testing period. The calibrations of the process probe were checked by comparing its predictions to those of the validated laboratory probe. The monitoring system could be automated to a large extent, and product quality could be improved considerably. The established technology is of high importance for the pharmaceutical industry carrying out high-throughput routine analysis because of its advantages in terms of of time and cost reductions.

Design and control of one precise tracking simulation bed for Chinese 20/30 meter optic/infrared telescope

Science.gov (United States)

Ren, Changzhi; Li, Xiaoyan; Song, Xiaoli; Niu, Yong; Li, Aihua; Zhang, Zhenchao

2012-09-01

Direct drive technology is the key to solute future 30-m and larger telescope motion system to guarantee a very high tracking accuracy, in spite of unbalanced and sudden loads such as wind gusts and in spite of a structure that, because of its size, can not be infinitely stiff. However, this requires the design and realization of unusually large torque motor that the torque slew rate must be extremely steep too. A conventional torque motor design appears inadequate. This paper explores one redundant unit permanent magnet synchronous motor and its simulation bed for 30-m class telescope. Because its drive system is one high integrated electromechanical system, one complexly electromechanical design method is adopted to improve the efficiency, reliability and quality of the system during the design and manufacture circle. This paper discusses the design and control of the precise tracking simulation bed in detail.

DNA-induced inter-particle cross-linking during expanded bed adsorption chromatography - Impact on future support design

DEFF Research Database (Denmark)

Theodossiou, Irini; Thomas, Owen R. T.

2002-01-01

(M(r)similar to50 000) and the other with long dextran (M(r)similar to500000) chains weakly derivatised with DEAE. However, the ability of the surfaces of these two matrices to bring about bed contraction, was strikingly different. The highly charged surface afforded by coupling of polyethyleneimine...... exhibited a three-fold higher tendency to interact with neighbouring particles in the presence of DNA than that of the dextran DEAE support. The implications of these findings on the design of future expanded bed materials for separation of both proteins and nucleic acids are discussed....

Root Cause Assessment of Pressure Drop Rise of a Packed Bed of Lithium Hydroxide in the International Space Station Trace Contaminant Control System

Science.gov (United States)

Aguilera, Tatiana; Perry, Jay L.

2009-01-01

The trace contaminant control system (TCCS) located in the International Space Station s (ISS) U.S. laboratory module employs physical adsorption, thermal catalytic oxidation, and chemical adsorption to remove trace chemical contamination produced by equipment offgassing and anthropogenic sources from the cabin atmosphere. The chemical adsorption stage, consisting of a packed bed of granular lithium hydroxide (LiOH), is located after the thermal catalytic oxidation stage and is designed to remove acid gas byproducts that may be formed in the upstream oxidation stage. While in service on board the ISS, the LiOH bed exhibited a change in flow resistance that leading to flow control difficulties in the TCCS. Post flight evaluation revealed LiOH granule size attrition among other changes. An experimental program was employed to investigate mechanisms hypothesized to contribute to the change in the packed bed s flow resistance. Background on the problem is summarized, including a discussion of likely mechanisms. The experimental program is described, results are presented, and implications for the future are discussed.

Congestion control and routing over satellite networks

Science.gov (United States)

Cao, Jinhua

Satellite networks and transmissions find their application in fields of computer communications, telephone communications, television broadcasting, transportation, space situational awareness systems and so on. This thesis mainly focuses on two networking issues affecting satellite networking: network congestion control and network routing optimization. Congestion, which leads to long queueing delays, packet losses or both, is a networking problem that has drawn the attention of many researchers. The goal of congestion control mechanisms is to ensure high bandwidth utilization while avoiding network congestion by regulating the rate at which traffic sources inject packets into a network. In this thesis, we propose a stable congestion controller using data-driven, safe switching control theory to improve the dynamic performance of satellite Transmission Control Protocol/Active Queue Management (TCP/AQM) networks. First, the stable region of the Proportional-Integral (PI) parameters for a nominal model is explored. Then, a PI controller, whose parameters are adaptively tuned by switching among members of a given candidate set, using observed plant data, is presented and compared with some classical AQM policy examples, such as Random Early Detection (RED) and fixed PI control. A new cost detectable switching law with an interval cost function switching algorithm, which improves the performance and also saves the computational cost, is developed and compared with a law commonly used in the switching control literature. Finite-gain stability of the system is proved. A fuzzy logic PI controller is incorporated as a special candidate to achieve good performance at all nominal points with the available set of candidate controllers. Simulations are presented to validate the theory. An effocient routing algorithm plays a key role in optimizing network resources. In this thesis, we briefly analyze Low Earth Orbit (LEO) satellite networks, review the Cross Entropy (CE

Tumour bed boost radiotherapy for women after breast-conserving surgery.

Science.gov (United States)

Kindts, Isabelle; Laenen, Annouschka; Depuydt, Tom; Weltens, Caroline

2017-11-06

Breast-conserving therapy, involving breast-conserving surgery followed by whole-breast irradiation and optionally a boost to the tumour bed, is a standard therapeutic option for women with early-stage breast cancer. A boost to the tumour bed means that an extra dose of radiation is applied that covers the initial tumour site. The rationale for a boost of radiotherapy to the tumour bed is that (i) local recurrence occurs mostly at the site of the primary tumour because remaining microscopic tumour cells are most likely situated there; and (ii) radiation can eliminate these causative microscopic tumour cells. The boost continues to be used in women at high risk of local recurrence, but is less widely accepted for women at lower risk. Reasons for questioning the boost are twofold. Firstly, the boost brings higher treatment costs. Secondly, the potential adverse events are not negligible. In this Cochrane Review, we investigated the effect of the tumour bed boost on local control and side effects. To assess the effects of tumour bed boost radiotherapy after breast-conserving surgery and whole-breast irradiation for the treatment of breast cancer. We searched the Cochrane Breast Cancer Specialised Register, the Cochrane Central Register of Controlled Trials (CENTRAL), MEDLINE (January 1966 to 1 March 2017), Embase (1980 to 1 March 2017), the World Health Organization International Clinical Trials Registry Platform, and ClinicalTrials.gov on 1 March 2017. We also searched the European Society of Radiotherapy and Oncology Annual Meeting, the St Gallen Oncology Conferences, and the American Society for Radiation Oncology Annual Meeting for abstracts. Randomised controlled trials comparing the addition and the omission of breast cancer tumour bed boost radiotherapy. Two review authors (IK and CW) performed data extraction and assessed risk of bias using Cochrane's 'Risk of bias' tool, resolving any disagreements through discussion. We entered data into Review Manager 5 for

Effect of almond consumption on vascular function in patients with coronary artery disease: a randomized, controlled, cross-over trial.

Science.gov (United States)

Chen, C-Y Oliver; Holbrook, Monika; Duess, Mai-Ann; Dohadwala, Mustali M; Hamburg, Naomi M; Asztalos, Bela F; Milbury, Paul E; Blumberg, Jeffrey B; Vita, Joseph A

2015-06-17

Almonds reduce cardiovascular disease risk via cholesterol reduction, anti-inflammation, glucoregulation, and antioxidation. The objective of this randomized, controlled, cross-over trial was to determine whether the addition of 85 g almonds daily to a National Cholesterol Education Program (NCEP) Step 1 diet (ALM) for 6 weeks would improve vascular function and inflammation in patients with coronary artery disease (CAD). A randomized, controlled, crossover trial was conducted in Boston, MA to test whether as compared to a control NCEP Step 1 diet absent nuts (CON), incorporation of almonds (85 g/day) into the CON diet (ALM) would improve vascular function and inflammation. The study duration was 22 weeks including a 6-weeks run-in period, two 6-weeks intervention phases, and a 4-weeks washout period between the intervention phases. A total of 45 CAD patients (27 F/18 M, 45-77 y, BMI = 20-41 kg/m(2)) completed the study. Drug therapies used by patients were stable throughout the duration of the trial. The addition of almonds to the CON diet increased plasma α-tocopherol status by a mean of 5.8%, reflecting patient compliance (P ≤0.05). However, the ALM diet did not alter vascular function assessed by measures of flow-mediated dilation, peripheral arterial tonometry, and pulse wave velocity. Further, the ALM diet did not significantly modify the serum lipid profile, blood pressure, C-reactive protein, tumor necrosis factor-α or E-selectin. The ALM diet tended to decrease vascular cell adhesion molecule-1 by 5.3% (P = 0.064) and increase urinary nitric oxide by 17.5% (P = 0.112). The ALM intervention improved the overall quality of the diet by increasing calcium, magnesium, choline, and fiber intakes above the Estimated Average Requirement (EAR) or Recommended Dietary Allowance (RDA). Thus, the addition of almonds to a NECP Step 1 diet did not significantly impact vascular function, lipid profile or systematic inflammation in CAD patients receiving

Environmental characterization of bedded salt formations and overlying areas of the Permian Basin

International Nuclear Information System (INIS)

1983-07-01

This report constitutes one input to the first stage of site qualification studies. It presents a general environmental characterization of the region that is underlain by the Permian bedded salt formation. The formation covers portions of Colorado, Kansas, New Mexico, Oklahoma, and Texas. The Permian bedded salt formation is one of a number of deep, stable geologic formations being studied for potential locations for nuclear waste repositories. These studies will not necessarily lead to selection of a site. They are intended only to provide information necessary to evaluate the suitability of locations for repositories. The report is intended as a general characterization of the existing environmental setting of the Permian Region with emphasis on land, water, and air characteristics; resources; plant and animal life; and man's organizations and activities. The report provides background information about the role that this regional study will play in the overall plan for environmental impact assessments and statements deemed necessary as input to the decision-making process. Background information on the present concept of nuclear waste repository design and function is also included. The information presented in this report has been summarized from open literature readily accessible to the public. No field work was conducted nor new data used in developing the descriptions contained herein

Glacier seismology: eavesdropping on the ice-bed interface

Science.gov (United States)

Walter, F.; Röösli, C.

2015-12-01

Glacier sliding plays a central role in ice dynamics. A number of remote sensing and deep drilling initiatives have therefore focused on the ice-bed interface. Although these techniques have provided valuable insights into bed properties, they do not supply theorists with data of sufficient temporal and spatial resolution to rigorously test mathematical sliding laws. As an alternative, passive seismic techniques have gained popularity in glacier monitoring. Analysis of glacier-related seismic sources ('icequakes') has become a useful technique to study inaccessible regions of the cryosphere, including the ice-bed interface. Seismic monitoring networks on the polar ice sheets have shown that ice sliding is not only a smooth process involving viscous deformation and regelation of basal ice layers. Instead, ice streams exhibit sudden slip episodes over their beds and intermittent phases of partial or complete stagnation. Here we discuss new and recently published discoveries of basal seismic sources beneath various glacial bodies. We revisit basal seismicity of hard-bedded Alpine glaciers, which is not the result of pure stick-slip motion. Sudden changes in seismicity suggest that the local configuration of the subglacial drainage system undergoes changes on sub daily time scales. Accordingly, such observations place constraints on basal resistance and sliding of hard-bedded glaciers. In contrast, certain clusters of stick-slip dislocations associated with micro seismicity beneath the Greenland ice sheet undergo diurnal variations in magnitudes and inter event times. This is best explained with a soft till bed, which hosts the shear dislocations and whose strength varies in response to changes in subglacial water pressure. These results suggest that analysis of basal icequakes is well suited for characterizing glacier and ice sheet beds. Future studies should address the relative importance between "smooth" and seismogenic sliding in different glacial environments.

Breakup and reestablishment of the armour layer in a large gravel-bed river below dams: The lower Ebro

Science.gov (United States)

Vericat, Damia; Batalla, Ramon J.; Garcia, Celso

2006-06-01

Changes in armour layer during floods under supply limited conditions are little known. This paper describes the breakup and the reestablishment of the bed armour layer in the regulated gravel-bed Ebro River during a flooding period. The study was conducted over a 28-km study reach from 2002 to 2004. The surface, subsurface and bed load grain size distribution constitute the bases for the analysis of bed-armouring dynamics. The results indicate that the magnitude of floods controlled the degree of armouring of the river bed. The initial mean armouring ratio was 2.3, with maximum values reaching 4.4. Floods in the winter of 2002-2003 ( Q8) caused the breakup of the armour layer in several sections. This resulted in the erratic bed load pattern observed during the December 2002 flushing flow and in the increase in bed load transport during successive events. Most grain size classes were entrained and transported, causing river bed incision. The mean armouring ratio decreased to 1.9. In contrast, during low magnitude floods in 2003-2004 ( Q2), the coarsest fractions (64 mm) did not take part in the bed load while finer particles were winnowed, thus surface deposits coarsened. As a result, the armour layer was reestablished (i.e., the mean armouring ratio increased to 2.3), and the supply of subsurface sediment decreased. The supply and transport of bed material appear to be in balance in the river reach immediately below the dam. In contrast, the transport of medium and finer size classes in the downstream reaches was higher than their supply from upstream, a phenomenon that progressively reduced their availability in the river bed surface, hence the armour layer reworking.

Bed Bugs are Public Health Pests

Science.gov (United States)

EPA and the Centers for Disease Control and Prevention (CDC) issued a joint statement on the public health impacts of bed bugs, which are blood-sucking ectoparasites (external parasites). EPA also has a pesticide registration notice on this topic.

Nail bed expansion: A new technique for correction of multiple isolated congenital micronychia

Directory of Open Access Journals (Sweden)

Gholamhossein Ghaffarpour

2014-01-01

Full Text Available Congenital micronychia may involve big toes or may involve other nails. The etiology of micronychia is not clear but amniotic bands, teratogens (drugs, alcohol, Nail Patella Syndrome etc. A 44-year-old woman with multiple isolated congenital micronychia over her hands and feet was selected. The major affected nails were thumbs and Index fingers. Surgical method were done step by step: Anesthesia of the area, extraction of short nail, elevation of nail bed, longitudinal nail bed incisions, suturing the lateral nail bed to the nail wall, covering the nail bed by a splint of plastic suction tube, bandage with gauze Vaseline. Finally, we hypnotized that in congenital micronychia, the main pathology is in nail bed; through this theory by nail bed expansion better outcomes are coming.

The thermal conductivity of beds of spheres

International Nuclear Information System (INIS)

McElroy, D.L.; Weaver, F.J.; Shapiro, M.; Longest, A.W.; Yarbrough, D.W.

1987-01-01

The thermal conductivities (k) of beds of solid and hollow microspheres were measured using two radial heat flow techniques. One technique provided k-data at 300 K for beds with the void spaces between particles filled with argon, nitrogen, or helium from 5 kPa to 30 MPa. The other technique provided k-data with air at atmospheric pressure from 300 to 1000 K. The 300 K technique was used to study bed systems with high k-values that can be varied by changing the gas type and gas pressure. Such systems can be used to control the operating temperature of an irradiation capsule. The systems studied included beds of 500 μm dia solid Al 2 O 3 , the same Al 2 O 3 spheres mixed with spheres of silica--alumina or with SiC shards, carbon spheres, and nickel spheres. Both techniques were used to determine the k-value of beds of hollow spheres with solid shells of Al 2 O 3 , Al 2 O 3 /center dot/7 w/o Cr 2 O 3 , and partially stabilized ZrO 2 . The hollow microspheres had diameters from 2100 to 3500 μm and wall thicknesses from 80 to 160 μm. 12 refs., 7 figs., 4 tabs

CFD-DEM simulation of a conceptual gas-cooled fluidized bed nuclear reactor

International Nuclear Information System (INIS)

Almeida, Lucilla C.; Su, Jian

2015-01-01

Several conceptual designs of the fluidized-bed nuclear reactor have been proposed due to its many advantages over conventional nuclear reactors such as PWRs and BWRs. Amongst their characteristics, the enhanced heat transfer and mixing enables a more uniform temperature distribution, reducing the risk of hot-spot and excessive fuel temperature, in addition to resulting in a higher burnup of the fuel. Furthermore, the relationship between the bed height and reactor neutronics turns the coolant flow rate control into a power production mechanism. Moreover, the possibility of removing the fuel by gravity from the movable core in case of a loss-of-cooling accident increases its safety. High-accuracy modeling of particles and coolant flow in fluidized bed reactors is needed to evaluate reliably the thermal-hydraulic efficiency and safety margin. The two-way coupling between solid and fluid can account for high-fidelity solid-solid interaction and reasonable accuracy in fluid calculation and fluid-solid interaction. In the CFD-DEM model, the particles are modeled as a discrete phase, following the DEM approach, whereas the fluid flow is treated as a continuous phase, described by the averaged Navier-Stokes equations on a computational cell scale. In this work, the coupling methodology between Fluent and Rocky is described. The numerical approach was applied to the simulation of a bubbling fluidized bed and the results were compared to experimental data and showed good agreement. (author)

Geomechanics of bedded salt

International Nuclear Information System (INIS)

Serata, S.; Milnor, S.W.

1979-01-01

Creep data from the literature search is reinterpreted by SGI, resulting in a better understanding of the temperature and stress state dependence of the octahedral creep rate and the octahedral shear strength. The concept of a transition strength between the elastic and the plastic states is in agreement with the data. The elastic and rheological properties of salt are described, and a set of constitutive equations is presented. The dependence of material properties on parameters such as temperature is considered. Findings on the permeability of salt are summarized, and the in-situ behavior of openings in bedded salt is described based on extensive engineering experience. A stress measuring system utilizing a finite element computer code is discussed. Geological factors affecting the stability of salt openings are considered, and the Stress Control Technique for designing stable openings in bedded salt formations is explained

Effect of bed particles to combustion of gases in fluidized bed

Energy Technology Data Exchange (ETDEWEB)

Raiko, R.; Wallen, V.; Etelaeaho, R.; Correia, S. [Tampere Univ. of Technology (Finland). Energy and Process Engineering

1997-10-01

The objective of this project was to obtain experimental data on effects of sand particles to the combustion of gases. The effect of the surface area of the particles was tested using different sized particles. The fluidized bed reactor used in these experiments was a stainless-steel tube with an internal diameter of 42 mm surrounded by an electric heater. The test rig was built in the Laboratory of Energy and Process Engineering at Tampere University of Technology. In order to elucidate the possible changes of particle surface, microscopic and porosimetric studies were conducted with both fresh bed particles and used bed particles. These measurements indicate that carbon monoxide significantly reacts with oxygen in the particulate or emulsion phase of a fluidized bed, if the residence time is long enough. The reaction rate depends mainly on temperature, air coefficient, residence time and particle size of the solids. It seems that the combustion enhances if the average particle size increases. Whether this is caused by increased free path length or reduced specific surface area of the bed is yet unknown. The first might be more probable cause because the majority of reactions often took place in the freeboard right above the bed. It was clear that the bed hindered proper combustion in several cases. (orig.)

Is parent-child bed-sharing a risk for wheezing and asthma in early childhood?

Science.gov (United States)

Luijk, Maartje P C M; Sonnenschein-van der Voort, Agnes M M; Mileva-Seitz, Viara R; Jansen, Pauline W; Verhulst, Frank C; Hofman, Albert; Jaddoe, Vincent W V; de Jongste, Johan C; van IJzendoorn, Marinus H; Duijts, Liesbeth; Tiemeier, Henning

2015-03-01

Household crowding can place young children at risk for respiratory infections which subsequently provoke asthma symptoms. However, crowding might also protect against asthma, in accordance with the hygiene hypothesis. We tested if parent-infant bed-sharing, an important dimension of household crowding, increases or decreases the risk for asthma. In a population-based prospective cohort (N = 6160) we assessed bed-sharing at 2 and 24 months; wheezing between 1 and 6 years of age; and asthma at 6 years of age. Generalised estimating equation models were used to assess repeated measures of wheezing and asthma. We found no association between bed-sharing in early infancy and wheezing or diagnosis of asthma. By contrast, we found a positive association between bed-sharing in toddlerhood and both wheezing (OR 1.42, 95% CI 1.15-1.74) and asthma (OR 1.57, 95% CI 1.03-2.38). Wheezing was not associated with bed-sharing when using cross-lagged modelling. This study suggests that bed-sharing in toddlerhood is associated with an increased risk of asthma at later ages, and not vice versa. Further studies are needed to explore the underlying causal mechanisms. Copyright ©ERS 2015.

A cross-over from Sport Psychology to the Psychology of Music: An ...

African Journals Online (AJOL)

The primary aim of this research was to evaluate whether the cross-over from Sport Psychology to the Psychology of Music in terms of the knowledge base, intervention Psychological Skills Training (PST) protocols and psychometric measurements was meaningful. A second aim was to ascertain whether the psychological ...

Cross-validation Methodology between Ground and GPM Satellite-based Radar Rainfall Product over Dallas-Fort Worth (DFW) Metroplex

Science.gov (United States)

Chen, H.; Chandrasekar, V.; Biswas, S.

2015-12-01

Over the past two decades, a large number of rainfall products have been developed based on satellite, radar, and/or rain gauge observations. However, to produce optimal rainfall estimation for a given region is still challenging due to the space time variability of rainfall at many scales and the spatial and temporal sampling difference of different rainfall instruments. In order to produce high-resolution rainfall products for urban flash flood applications and improve the weather sensing capability in urban environment, the center for Collaborative Adaptive Sensing of the Atmosphere (CASA), in collaboration with National Weather Service (NWS) and North Central Texas Council of Governments (NCTCOG), has developed an urban radar remote sensing network in DFW Metroplex. DFW is the largest inland metropolitan area in the U.S., that experiences a wide range of natural weather hazards such as flash flood and hailstorms. The DFW urban remote sensing network, centered by the deployment of eight dual-polarization X-band radars and a NWS WSR-88DP radar, is expected to provide impacts-based warning and forecasts for benefit of the public safety and economy. High-resolution quantitative precipitation estimation (QPE) is one of the major goals of the development of this urban test bed. In addition to ground radar-based rainfall estimation, satellite-based rainfall products for this area are also of interest for this study. Typical example is the rainfall rate product produced by the Dual-frequency Precipitation Radar (DPR) onboard Global Precipitation Measurement (GPM) Core Observatory satellite. Therefore, cross-comparison between ground and space-based rainfall estimation is critical to building an optimal regional rainfall system, which can take advantages of the sampling differences of different sensors. This paper presents the real-time high-resolution QPE system developed for DFW urban radar network, which is based upon the combination of S-band WSR-88DP and X

Bed retained products in swept fixed bed (SFB) coal hydropyrolysis

Energy Technology Data Exchange (ETDEWEB)

Mastral, A.M.; Perez-Surio, M.J. [CSIC, Zaragosa (Spain). Inst. de Carboquimica

1997-12-31

The hydropyrolysis of a low rank coal in a swept fixed bed (SFB) reactor is carried out by fixing the hydrogen pressure (40 kg/cm{sup 2}), the hydrogen flow (2 l/min) and the residence time (10 min) at increasing temperatures (400 C, 500 C and 600 C) and coal bed heights (h, 1.5h, 2h, 2.5h and 3h). It is shown that the percentages of tars and char directly depend on the coal bed height and that there is not only a quantitative dependence, but also the height of the coal bed is very important and plays a relevant role on the nature of the conversion products. (orig.)

Thermo-catalytic pyrolysis of waste polyethylene bottles in a packed bed reactor with different bed materials and catalysts

International Nuclear Information System (INIS)

Obeid, Farah; Zeaiter, Joseph; Al-Muhtaseb, Ala’a H.; Bouhadir, Kamal

2014-01-01

Highlights: • Thermo-catalytic pyrolysis of waste polyethylene bottles was investigated. • The highest yield of liquid (82%) was obtained over a cement powder bed. • Acidic catalysts narrowed the carbon chain length of the paraffins to C 10 –C 28 . • Combination of cement bed with HBeta catalyst gave the highest yield of liquid. • Significant yield of aromatics was obtained mainly naphthalene and D-limonene. - Abstract: Plastic waste is an increasing economic and environmental problem as such there is a great need to process this waste and reduce its environmental impact. In this work, the pyrolysis of high density polyethylene (HDPE) waste products was investigated using both thermal and catalytic cracking techniques. The experimental work was carried out using packed bed reactor operating under an inert atmosphere at 450 °C. Different reactor bed materials, including sand, cement and white clay were used to enhance the thermal cracking of HDPE. In addition, the catalytic effect of sodium hydroxide, HUSY and HBeta zeolite catalysts on the degradation of HDPE waste was also investigated. The reactor beds were found to significantly alter the yield as well as the product composition. Products such as paraffins (⩽C 44 ), olefins (⩽C 22 ), aromatics (⩽C 14 ) and alcohols (C 16 and C 17 ) were obtained at varying rates. The highest yield of liquid (82%) was obtained over a cement powder bed with a paraffin yield of 58%. The yield of paraffins and olefins followed separate paths, for paraffins it was found to increase in the order or Cement > White clay > Silica Sand, whereas for the olefins it was in the reverse order Silica Sand > White clay > Cement. The results obtained in this work exhibited a higher P/O ratio than expected, where the amount of generated paraffins was greater than 60% in most cases. Less olefin was generated as a consequence. This indicates that the product generated is more suited to be used as a fuel rather than as a chemical

In-bed accountability of tritium in production scale metal hydride storage beds

International Nuclear Information System (INIS)

Klein, J.E.

1995-01-01

An ''in-bed accountability'' (IBA) flowing gas calorimetric measurement method has been developed and implemented to eliminate the need to remove tritium from production scale metal hydride storage beds for inventory measurement purposes. Six-point tritium IBA calibration curves have been completed for two, 390 gram tritium metal hydride storage beds. The calibration curves for the two tritium beds are similar to those obtained from the ''cold'' test program. Tritium inventory errors at the 95 percent confidence level ranged from ± 7.3 to 8.6 grams for the cold test results compared to ± 4.2 to 7.5 grams obtained for the two tritium calibrated beds

Surface-subsurface turbulent interaction at the interface of a permeable bed: influence of the wall permeability

Science.gov (United States)

Kim, T.; Blois, G.; Best, J.; Christensen, K. T.

2017-12-01

Coarse-gravel river beds possess a high degree of permeability. Flow interactions between surface and subsurface flow across the bed interface is key to a number of natural processes occurring in the hyporheic zone. In fact, it is increasingly recognized that these interactions drive mass, momentum and energy transport across the interface, and consequently control biochemical processes as well as stability of sediments. The current study explores the role of the wall permeability in surface and subsurface flow interaction under controlled experimental conditions on a physical model of a gravel bed. The present wall model was constructed by five layers of cubically arranged spheres (d=25.4mm, where d is a diameter) providing 48% of porosity. Surface topography was removed by cutting half of a diameter on the top layer of spheres to render the flow surface smooth and highlight the impact of the permeability on the overlying flow. An impermeable smooth wall was also considered as a baseline of comparison for the permeable wall flow. To obtain basic flow statistics, low-frame-rate high-resolution PIV measurements were performed first in the streamwise-wall-normal (x-y) plane and refractive-index matching was employed to optically access the flow within the permeable wall. Time-resolved PIV experiments in the same facility were followed to investigate the flow interaction across the wall interface in sptaio-temporal domain. In this paper, a detailed analysis of the first and second order velocity statistics as well as the amplitude modulation for the flow overlying the permeable smooth wall will be presented.

Addition of Bacillus sp. inoculums in bedding for swine on a pilot scale: effect on microbial population and bedding temperature.

Science.gov (United States)

Corrêa, E K; Ulguim, R R; Corrêa, L B; Castilhos, D D; Bianchi, I; Gil-Turnes, C; Lucia, T

2012-10-01

Thermal and microbiological characteristics of beddings for swine were compared according to their depth and of addition of inoculums. Bedding was added to boxes at 0.25 (25D) and 0.50 m (50D), with three treatments: control (no inoculums); T1, with 250 g of Bacillus cereus var. toyoii at 8.4 × 10(7) CFU; and T2, with 250 g of a pool of B. subtilis, Bacillus licheniformis and Bacillus polymyxa at 8.4 × 10(7) CFU (250 g for 25D and 500 g for 50D). Mean temperatures were 28.5 ± 3.9 at the surface and 35.2 ± 8.9 inside the beddings. The most probable number (MPN) of thermophilic bacteria was higher for T1 and T2 than for the control (P<0.05). The MPN of thermophilic bacteria and fungi was greater for D50 than for D25 (P<0.05). The use of 25D without inoculums is recommended due to the reduction of thermophilic microbiota. Copyright © 2012 Elsevier Ltd. All rights reserved.

Advanced sorbent development progam; development of sorbents for moving-bed and fluidized-bed applications

International Nuclear Information System (INIS)

Ayala, R.E.; Venkataramani, V.S.

1998-01-01

The integrated gasification combined cycle (IGCC) power system using high-temperature coal gas cleanup is one of the most promising advanced technologies for the production of electric power from coal in an environmentally acceptable manner. Unlike conventional low-temperature cleanup systems that require costly heat exchangers, high-temperature coal gas cleanup systems can be operated near 482-538 C (900-1000F) or higher, conditions that are a closer match with the gasifier and turbine components in the IGCC system, thus resulting is a more efficient overall system. GE is developing a moving-bed, high-temperature desulfurization system for the IGCC power cycle in which zinc-based regenerable sorbents are currently being used as desulfurization sorbents. Zinc titanate and other proprietary zinc-based oxides are being considered as sorbents for use in the Clean Coal Technology Demonstration Program at Tampa Electric Co.s (TECo) Polk Power Station. Under cold startup conditions at TECo, desulfurization and regeneration may be carried out at temperatures as low as 343 C (650 F), hence a versatile sorbent is desirable to perform over this wide temperature range. A key to success in the development of high-temperature desulfurization systems is the matching of sorbent properties for the selected process operating conditions, namely, sustainable desulfurization kinetics, high sulfur capacity, and mechanical durability over multiple cycles. Additionally, the sulfur species produced during regeneration of the sorbent must be in a form compatible with sulfur recovery systems, such as sulfuric acid or elemental sulfur processes. The overall objective of this program is to develop regenerable sorbents for hydrogen sulfide removal from coal-derived fuel gases in the temperature range 343-538 C (650-1000 F). Two categories of reactor configurations are being considered: moving-bed reactors and fluidized-bed (bubbling and circulating) reactors. In addition, a cost assessment and

Thermal Analysis of Fluidized Bed and Fixed Bed Latent Heat Thermal Storage System

Science.gov (United States)

Beemkumar, N.; Karthikeyan, A.; Shiva Keshava Reddy, Kota; Rajesh, Kona; Anderson, A.

2017-05-01

Thermal energy storage technology is essential because its stores available energy at low cost. Objective of the work is to store the thermal energy in a most efficient method. This work is deal with thermal analysis of fluidized bed and fixed bed latent heat thermal storage (LHTS) system with different encapsulation materials (aluminium, brass and copper). D-Mannitol has been used as phase change material (PCM). Encapsulation material which is in orbicular shape with 4 inch diameter and 2 mm thickness orbicular shaped product is used. Therminol-66 is used as a heat transfer fluid (HTF). Arrangement of encapsulation material is done in two ways namely fluidized bed and fixed bed thermal storage system. Comparison was made between the performance of fixed bed and fluidized bed with different encapsulation material. It is observed that from the economical point of view aluminium in fluidized bed LHTS System has highest efficiency than copper and brass. The thermal energy storage system can be analyzed with fixed bed by varying mass flow rate of oil paves a way to find effective heat energy transfer.

Neurophysiological effects of modafinil on cue-exposure in cocaine dependence: a randomized placebo-controlled cross-over study using pharmacological fMRI.

Science.gov (United States)

Goudriaan, Anna E; Veltman, Dick J; van den Brink, Wim; Dom, Geert; Schmaal, Lianne

2013-02-01

Enhanced reactivity to substance related cues is a central characteristic of addiction and has been associated with increased activity in motivation, attention, and memory related brain circuits and with a higher probability of relapse. Modafinil was promising in the first clinical trials in cocaine dependence, and was able to reduce craving in addictive disorders. However, its mechanism of action remains to be elucidated. In this functional magnetic resonance imaging (fMRI) study therefore, cue reactivity in cocaine dependent patients was compared to cue reactivity in healthy controls (HCs) under modafinil and placebo conditions. An fMRI cue reactivity study, with a double-blind, placebo-controlled cross-over challenge with a single dose of modafinil (200mg) was employed in 13 treatment seeking cocaine dependent patients and 16 HCs. In the placebo condition, watching cocaine-related pictures (versus neutral pictures) resulted in higher brain activation in the medial frontal cortex, anterior cingulate cortex, angular gyrus, left orbitofrontal cortex, and ventral tegmental area (VTA) in the cocaine dependent group compared to HCs. However, in the modafinil condition, no differences in brain activation patterns were found between cocaine dependent patients and HCs. Group interactions revealed decreased activity in the VTA and increased activity in the right ACC and putamen in the modafinil condition relative to the placebo condition in cocaine dependent patients, whereas such changes were not present in healthy controls. Decreases in self-reported craving when watching cocaine-related cues after modafinil administration compared to the placebo condition were associated with modafinil-induced increases in ACC and putamen activation. Enhanced cue reactivity in the cocaine dependent group compared to healthy controls was found in brain circuitries related to reward, motivation, and autobiographical memory processes. In cocaine dependent patients, these enhanced brain

Engineered channel controls limiting spawning habitat rehabilitation success on regulated gravel-bed rivers

Science.gov (United States)

Brown, Rocko A.; Pasternack, Gregory B.

2008-05-01

In efforts to rehabilitate regulated rivers for ecological benefits, the flow regime has been one of the primary focal points of management strategies. However, channel engineering can impact channel geometry such that hydraulic and geomorphic responses to flow reregulation do not yield the sought for benefits. To illustrate and assess the impacts of structural channel controls and flow reregulation on channel processes and fish habitat quality in multiple life stages, a highly detailed digital elevation model was collected and analyzed for a river reach right below a dam using a suite of hydrologic, hydraulic, geomorphic, and ecological methods. Results showed that, despite flow reregulation to produce a scaled-down natural hydrograph, anthropogenic boundary controls have severely altered geomorphic processes associated with geomorphic self-sustainability and instream habitat availability in the case study. Given the similarity of this stream to many others, we concluded that the potential utility of natural flow regime reinstatement in regulated gravel-bed rivers is conditional on concomitant channel rehabilitation.

Chemical characteristics of beddings for swine: effects of bedding depths and of addition of inoculums in a pilot-scale.

Science.gov (United States)

Corrêa, E K; Corezzolla, J L; Corrêa, M N; Bianchi, I; Gil-Turnes, C; Lucia, T

2012-11-01

The effect of depths and of addition of inoculums on the chemical content of swine beddings was evaluated. For beddings 0.25m (25D) and 0.50m (50D) deep, three treatments were tested in two repeats with the same beddings: control (no inoculums); T1 (250g of Bacillus cereus var. toyoii at 8.4×10(7)CFU/g); and T2 (250g of a pool of Bacillus sp. at 8.4×10(7)CFU/g) (250g for 25D and 500g for 50D). For 25D, the C:N ratio was lower, but N, K and C contents were greater than for 50D (P0.05). In the second repeat, beddings presented lower C:N ratio and greater N, P and K contents than in the first repeat (P<0.05). Thus, the compost produced after using 25D twice had greater fertilizer value than that of 50D. Copyright © 2012 Elsevier Ltd. All rights reserved.

Crud removal with deep bed type condensate demineralizer in Tokai-2 BWR

International Nuclear Information System (INIS)

Abe, Ayumi; Takiguchi, Hideki; Numata, Kunio; Saito, Toshihiko

1996-01-01

The major objective and functions for the installation of the deep bed type condensate polishers in BWR power plants is to remove both ionic impurities caused by sea water leakage and suspended impurities called crud mainly consisting of metal oxides which are produced from metal corrosion. In considering the reduction of occupational radiation exposure level, it is extremely important to remove the crud effectively. In recent Japanese BWR power plants, condensate pre-filters with powdered ion exchange resins or with hollow fiber membrane have been installed to remove the crud at the upper stream of the deep bed polishers. In such plants, the crud removal is conventionally the secondary objective for the deep bed polishers. The Japan Atomic Power Company has introduced the small particle ion exchange resin and a soak regeneration method since April 1985, and then applied the low cross-linked resin since July 1995 at Tokai-2 Power Station, to improve the crud removal performance by using only deep bed type condensate demineralizer, and as a result condensate demineralizer outlet iron level has been kept below 1 ppb since 1991

Experimental and Numerical Research Activity on a Packed Bed TES System

Directory of Open Access Journals (Sweden)

Mario Cascetta

2016-09-01

Full Text Available This paper presents the results of experimental and numerical research activities on a packed bed sensible thermal energy storage (TES system. The TES consists of a cylindrical steel tank filled with small alumina beads and crossed by air used as the heat transfer fluid. Experimental tests were carried out while varying some operating parameters such as the mass flow rate, the inlet–outlet temperature thresholds and the aspect ratio (length over diameter. Numerical simulations were carried out using a one-dimensional model, specifically developed in the Matlab-Simulink environment and a 2D axisymmetric model based on the ANSYS-Fluent platform. Both models are based on a two-equation transient approach to calculate fluid and solid phase temperatures. Thermodynamic properties were considered to be temperature-dependent and, in the Computational Fluid Dynamics (CFD model, variable porosity of the bed in the radial direction, thermal losses and the effective conductivity of the alumina beads were also considered. The simulation results of both models were compared to the experimental ones, showing good agreement. The one-dimensional model has the advantage of predicting the axial temperature distribution with a very low computational cost, but it does not allow calculation of the correct energy stored when the temperature distribution is strongly influenced by the wall. To overcome this problem a 2D CFD model was used in this work.

Feasibility of Using Rice Hulls as Bedding for Laboratory Mice.

Science.gov (United States)

Carbone, Elizabeth T; Kass, Philip H; Evans, Kristin D

2016-01-01

Factors that are considered when selecting laboratory mouse bedding include animal health and comfort, cost, effects on personnel, and bioactive properties. Corncob is economical and facilitates low intracage ammonia but has undesirable influences on some endocrine studies. Rice hulls are an economical material that has not been well characterized as a bedding substrate. In this pilot study, we compared various aspects of bedding performance of rice hulls and other materials. On a per-volume basis, rice hulls were less absorbent than was corncob bedding. Rice hulls had higher odds than did corncob or reclaimed wood pulp of having moisture present at the bedding surface. The results of the absorbency tests coupled with the results of preliminary monitoring of intracage ammonia raised concern about the ability of rice hulls to control ammonia levels sufficiently in cages with high occupancy. However, ammonia was negligible when cages contained 5 young adult female mice. The relative expression of 3 cytochrome p450 genes was compared among mice housed on rice hulls, corncob, reclaimed wood pulp, or pine shavings. The expression of Cyp1a2 was 1.7 times higher in the livers of mice housed on rice hulls than on pine shavings, but other differences were not statistically significant. This study provides information on the merits of rice hulls as laboratory mouse bedding. Their relatively poor moisture control is a major disadvantage that might preclude their widespread use.

Bed care for patients in palliative settings: considering risks to caregivers and bed surfaces.

Science.gov (United States)

Fragala, Guy

2015-02-01

Ensuring patients are comfortable in bed is key to effective palliative care, but when moving and positioning patients in bed, health professionals face an occupational risk of injury. The turning and positioning (TAP) system is a new method of moving patients in bed, that evidence has shown to reduce the risk of injury to caregivers. Providing the correct bed surface is another aspect of bed care essential to the comfort of the palliative patient, and to aid wound prevention and treatment. It is important to take a patient-centred approach when considering the most appropriate bed surface patients. This article provides an overview and discussion of these two aspects of bed care for palliative patients.

Analysis of the start-up and control of a particle bed reactor

International Nuclear Information System (INIS)

Lazareth, O.W.; Araj, K.J.; Horn, F.L.; Ludewig, H.; Powell, J.R.

1987-01-01

This study describes the modeling of start-up transients in Particle Bed Reactors (PBR) for burst electric power. Two computer programs have been developed to analyze the start-up process. The first program (named KINETIC) analyzes the entire fuel element, calculating time dependent solutions for power and the temperature distribution in the packed bed. The second program (named SPHEAT, for Spherical Heating) calculates time-dependent temperatures inside individual, cladded fuel particles. The two programs provide powerful analytical tools for evaluation of material and geometrical options, power and time constraints, and conditions that could lead to element failures

Fluid bed porosity equation for an inverse fluidized bed bioreactor with particles growing biofilm

International Nuclear Information System (INIS)

Campos-Diaz, K. E.; Limas-Ballesteros, R.

2009-01-01

Fluid Bed Bioreactor performance is strongly affected by bed void fraction or bed porosity fluctuations. Particle size enlargement due to biofilm growth is an important factor that is involved in these variations and until now there are no mathematical equations that consider biofilm growth. In this work a mathematical equation is proposed to calculate bed void fraction in an inverse fluid bed bioreactor. (Author)

Comparison of Three Bed Bug Management Strategies in a Low-Income Apartment Building

Directory of Open Access Journals (Sweden)

Changlu Wang

2012-04-01

Full Text Available Bed bug (Cimex lectularius L. infestations are currently controlled by a variety of non-chemical and chemical methods. There have been few studies on the comparative effectiveness of these control techniques. We evaluated three bed bug management strategies in an apartment building: (1 non-chemical methods only (n = 9; (2 insecticides only (n = 6; and (3 integrated pest management including both non-chemical methods and insecticides (n = 9. The apartments were one-bedroom units occupied by seniors or people with disabilities. Bed bug numbers in each apartment were determined by visual inspection and/or installing intercepting devices under bed and sofa legs. The median (min, max bed bug counts in the non-chemical methods only, insecticides only, and integrated pest management (IPM treatment were: 4 (1, 57, 19 (1, 250, and 14 (1, 219, respectively prior to the treatments. The apartments were retreated if found necessary during biweekly to monthly inspections. After 10 weeks, bed bugs were found to be eliminated from 67, 33, and 44% of the apartments in the three treatment groups, respectively. The final (after 10 weeks median (min, max bed bug counts in the non-chemical methods only, insecticides only, and IPM treatment were: 0 (0, 134, 11.5 (0, 58, and 1 (0, 38, respectively. There were no significant differences in the speed of bed bug count reduction or the final bed bug counts. Lack of resident cooperation partially contributed to the failure in eliminating bed bugs from some of the apartments. Results of this study suggest that non-chemical methods can effectively eliminate bed bugs in lightly infested apartments.

Seasonal and interannual cross-shelf transport over the Texas and Louisiana continental shelf

Science.gov (United States)

Thyng, Kristen M.; Hetland, Robert D.

2018-05-01

Numerical drifters are tracked in a hydrodynamic simulation of circulation over the Texas-Louisiana shelf to analyze patterns in cross-shelf transport of materials. While the important forcing mechanisms in the region (wind, river, and deep eddies) and associated flow patterns are known, the resultant material transport is less well understood. The primary metric used in the calculations is the percent of drifters released within a region that cross the 100 m isobath. Results of the analysis indicate that, averaged over the eleven years of the simulation, there are two regions on the shelf - over the Texas shelf during winter, and over the Louisiana shelf in summer - with increased seasonal probability for offshore transport. Among the two other distinct regions, the big bend region in Texas has increased probability for onshore transport, and the Mississippi Delta region has an increase in offshore transport, for both seasons. Some of these regions of offshore transport have marked interannual variability. This interannual variability is correlated to interannual changes in forcing conditions. Winter transport off of the Texas shelf is correlated with winter mean wind direction, with more northerly winds enhancing offshore transport; summer transport off the Louisiana shelf is correlated with Mississippi River discharge.

Tranexamic acid for epistaxis in hereditary hemorrhagic telangiectasia patients: a European cross-over controlled trial in a rare disease.

Science.gov (United States)

Gaillard, S; Dupuis-Girod, S; Boutitie, F; Rivière, S; Morinière, S; Hatron, P-Y; Manfredi, G; Kaminsky, P; Capitaine, A-L; Roy, P; Gueyffier, F; Plauchu, H

2014-09-01

Hereditary hemorrhagic telangiectasia (HHT) is a genetic disorder associated with abnormal angiogenesis and disabling epistaxis. Tranexamic acid (TA) has been widely used in the treatment of these severe bleeds but with no properly designed trial. To demonstrate the efficacy of TA in epistaxis in HHT patients and to explore its safety of use. A randomized, placebo-controlled, double-blind, cross-over trial was conducted. Participants were randomized to receive TA (3 g a day) then placebo or the opposite sequence. The main analysis compared intra-individual mean duration of epistaxis under TA vs. placebo on a log scale. The primary outcome was the mean duration of epistaxis per month, assessed with specific grids to be completed by participants. The number of epistaxis episodes was recorded as a secondary outcome. A total of 118 randomized patients contributed to the statistical analysis. The mean duration of epistaxis per month was significantly shorter with TA than placebo (0.19 on the log scale; SD = 0.07; P = 0.005), corresponding to a decrease of 17.3% (15.7 min) in the duration of epistaxis per month (CI 95%, 5.5-27.6). The median number of epistaxis episodes per month was 22.1 episodes in the placebo arm vs. 23.3 episodes in the TA arm. No thrombophlebitis was observed. In the ATERO study, we demonstrated a significant decrease in the duration of epistaxis in HHT patients taking TA. No safety issues were recorded in our cohort of patients. © 2014 International Society on Thrombosis and Haemostasis.

The longitudinal relationship between control over working hours and depressive symptoms: Results from SLOSH, a population-based cohort study.

Science.gov (United States)

Albrecht, Sophie C; Kecklund, Göran; Rajaleid, Kristiina; Leineweber, Constanze

2017-06-01

Psychosocial work factors can affect depressive moods, but research is inconclusive if flexibility to self-determine working hours (work-time control, WTC) is associated with depressive symptoms over time. We investigated if either sub-dimension of WTC, control over daily hours and control over time off, was related to depressive symptoms over time and examined causal, reversed-causal, and reciprocal pathways. The study was based on four waves of the Swedish Longitudinal Occupational Survey of Health which is a follow-up of representative samples of the Swedish working population. WTC was measured using a 5-item index. Depressive symptoms were assessed with a brief subscale of the Symptom Checklist. Latent growth curve models and cross-lagged panel models were tested. Best fit was found for a model with correlated intercepts (control over daily hours) and both correlated intercepts and slopes (control over time off) between WTC and depressive symptoms, with stronger associations for control over time off. Causal models estimating impacts from WTC to subsequent depressive symptoms were best fitting, with a standardised coefficient between -0.023 and -0.048. Results were mainly based on self-report data and mean age in the study sample was relatively high. Higher WTC was related to fewer depressive symptoms over time albeit small effects. Giving workers control over working hours - especially over taking breaks and vacation - may improve working conditions and buffer against developing depression, potentially by enabling workers to recover more easily and promoting work-life balance. Copyright © 2017 Elsevier B.V. All rights reserved.

Non-local rheology of stony debris flow propagating over a cohesionless sediment bed

Science.gov (United States)

Lanzoni, Stefano; Gregoretti, Carlo

2016-04-01

normal to the flow, with particular attention to the role played by frictional stresses near to the movable bed over which the debris flow propagates.

Traffic control on a railway crossing with elements of utility theory

Directory of Open Access Journals (Sweden)

Abramova L.S.

2016-08-01

Full Text Available An approach to the management of vehicles at a railway crossing in order to improve the road safety is considered. To do this, it is suggested to introduce the dynamic motion control modes on the road, which consist in reducing the speed at a certain distance from the railway crossing and depends on its condition. The value of the recommended speed is displayed on the managed road signs and is calculated in real-time traffic controller at the railway crossing control point. The mark location is determined based on traffic intensity equalization that affects both the traffic intensity of the railway crossing and the road section on the approach to it. To analyze such events directed to improve the traffic on level crossings it is suggested to use the elements of utility theory to further develop the traffic control algorithm. For this purpose there was built a decision tree for the existing conditions at the railway crossing and at the introduction of the dynamic management, which indicates the result of decision taken by the change in the selected criteria of efficiency of traffic management at the railway crossing. Such an approach can reduce the number of road accidents and to increase the capacity of vehicular traffic at a particular road section to the technical means of attracting the driver's attention to the complex road by forced reduction in speed not only before the railway crossing, but also in at the approach to it.

The optimal injection technique for the osteoarthritic ankle: A randomized, cross-over trial

NARCIS (Netherlands)

Witteveen, Angelique G. H.; Kok, Aimee; Sierevelt, Inger N.; Kerkhoffs, Gino M. M. J.; van Dijk, C. Niek

2013-01-01

Background: To optimize the injection technique for the osteoarthritic ankle in order to enhance the effect of intra-articular injections and minimize adverse events. Methods: Randomized cross-over trial. Comparing two injection techniques in patients with symptomatic ankle osteoarthritis. Patients

Quench cooling of superheated debris beds in containment during LWR core meltdown accidents

International Nuclear Information System (INIS)

Ginsberg, T.; Chen, J.C.

1984-01-01

Light water reactor core meltdown accident sequence studies suggest that superheated debris beds may settle on the concrete floor beneath the reactor vessel. A model for the heat transfer processes during quench (removal of stored energy from initial temperature to saturation temperature) of superheated debris beds cooled by an overlying pool of water has been presented in a prior paper. This paper discusses the coolability of decay-heated debris beds from the standpoint of their transient quench characteristics. It is shown that even though a debris bed configuration may be coolable from the point of view of steady-state decay heat removal, the quench behavior from an initially elevated temperature may lead to bed melting prior to quench of the debris

Childhood pneumonia and crowding, bed-sharing and nutrition: a case-control study from The Gambia.

Science.gov (United States)

Howie, S R C; Schellenberg, J; Chimah, O; Ideh, R C; Ebruke, B E; Oluwalana, C; Mackenzie, G; Jallow, M; Njie, M; Donkor, S; Dionisio, K L; Goldberg, G; Fornace, K; Bottomley, C; Hill, P C; Grant, C C; Corrah, T; Prentice, A M; Ezzati, M; Greenwood, B M; Smith, P G; Adegbola, R A; Mulholland, K

2016-10-01

Greater Banjul and Upper River Regions, The Gambia. To investigate tractable social, environmental and nutritional risk factors for childhood pneumonia. A case-control study examining the association of crowding, household air pollution (HAP) and nutritional factors with pneumonia was undertaken in children aged 2-59 months: 458 children with severe pneumonia, defined according to the modified WHO criteria, were compared with 322 children with non-severe pneumonia, and these groups were compared to 801 neighbourhood controls. Controls were matched by age, sex, area and season. Strong evidence was found of an association between bed-sharing with someone with a cough and severe pneumonia (adjusted OR [aOR] 5.1, 95%CI 3.2-8.2, P Malnutrition and pneumonia had clear evidence of association, which was strongest between severe malnutrition and severe pneumonia (aOR 8.7, 95%CI 4.2-17.8, P malnutrition remains an important tractable determinant.

Real-Time Measurement of Volatile Chemicals Released by Bed Bugs during Mating Activities

DEFF Research Database (Denmark)

Kilpinen, Ole Østerlund; Liu, Dezhao; Adamsen, Anders Peter

2012-01-01

In recent years, bed bug (Hemiptera: Cimicidae) problems have increased dramatically in many parts of the world, leading to a renewed interest in their chemical ecology. Most studies of bed bug semiochemicals have been based on the collection of volatiles over a period of time followed by chemical...