The control system based on PXI technology for high voltage power supply

International Nuclear Information System (INIS)

Chen Dehong; Zhang Ming; Ma Shaoxiang; Xia Linglong; Zeng Zhen; Zhang Xueliang; Wang Chuliang; Yu Kexun

2014-01-01

A 100 kV/60 A high voltage power supply (HVPS) is being developed to carry some auxiliary heating research on J-TEXT and supply the auxiliary heating system. The power supply which consists of 144 switch modules is based on PSM technology. For the requirement of isolation, control and protection, a control system based on the PCI extensions for instrumentation (PXI) which meets up with the CODAC standards is designed with developed PSM technology for the high voltage power supply. The compact structure of hardware in the control system is presented too. And the control strategy which is based on shift phase pulse width modulation is discussed Some tests are performed on the control system to validate the control strategy, the experimental results show that the system has a good control performance and fast response, which meets the control requirement of 100 kV/60 A high voltage power supply. (authors)

DISTURBANCE ERROR INVARIANCE IN AUTOMATIC CONTROL SYSTEMS FOR TECHNOLOGICAL OBJECT TRAJECTORY MOVEMENT

Directory of Open Access Journals (Sweden)

A. V. Lekareva

2016-09-01

Full Text Available We consider combined control in automatic control systems for technological objects trajectory movements. We present research results of the system disturbance invariance ensuring on the example of the technological manipulator that implements hydrocutting of the oil pipelines. Control is based on the propositions of the fourth modified invariance form with the use of bootstrapping methods. The paper presents analysis of results obtained by two different correction methods. The essence of the first method lies in injection of additional component into the already established control signal and formation of the channel for that component. Control signal correction during the signal synthesis stage in the control device constitutes the basis for the second method. Research results have shown high efficiency of application for both correction methods. Both methods have roughly the same precision. We have shown that the correction in the control device is preferable because it has no influence on the inner contour of the system. We have shown the necessity of the block usage with the variable transmission coefficient, which value is determined by technological trajectory parameters. Research results can be applied in practice for improvement of the precision specifications of automatic control systems for trajectorial manipulators.

METHODS FOR EVALUATION OF COMPANIES’ INFORMATION SYSTEMS AND TECHNOLOGIES EFFICIENCY AND CONTROL IN TEACHING COURSE "INFORMATION TECHNOLOGY GOVERNANCE"

Directory of Open Access Journals (Sweden)

Samchynska Yaroslava

2014-10-01

Full Text Available The use of the information systems and technologies in economic activity is called to represent companies’ corporate principles, aims, traditions, to help in realization of the planned strategies, thanks to that the management efficiency and the cost of enterprise increases. Teaching for educational discipline «IT Governance» is directed on a study and research of these intercommunications by students of the 5th course on specialties «Computer Science», «Software Engineering» for educational level Specialist (Past Bachelor Degree, Master degree. The auditing services belong to the actual methods for evaluation of the information systems and technologies efficiency and control, which are studied according to the course «IT Governance». The article deals with the methodological basis of providing auditing services for evaluation of efficiency and control of information systems (technologies for the purpose of satisfaction of growing informational needs of companies and functional activation in their information resources. The main task of auditing services for control of information systems (information communication technologies efficiency is to evaluate independently and objectively if the information technologies provide the necessary services. The basic criteria, data ware, subject and object of audit necessary for drawing up an audit report and assurance declaring are established. The program and a detailed list of auditing procedures for evaluation of efficiency of information systems and technologies have been presented

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Current and advanced act control system definition study

Science.gov (United States)

1982-01-01

The Current and Advanced Technology ACT control system definition tasks of the Integrated Application of Active Controls (IAAC) Technology project within the Energy Efficient Transport Program are summarized. The systems mechanize six active control functions: (1) pitch augmented stability; (2) angle of attack limiting; (3) lateral/directional augmented stability; (4) gust load alleviation; (5) maneuver load control; and (6) flutter mode control. The redundant digital control systems meet all function requirements with required reliability and declining weight and cost as advanced technology is introduced.

A Survey of Intelligent Control and Health Management Technologies for Aircraft Propulsion Systems

Science.gov (United States)

Litt, Jonathan S.; Simon, Donald L.; Garg, Sanjay; Guo, Ten-Heui; Mercer, Carolyn; Behbahani, Alireza; Bajwa, Anupa; Jensen, Daniel T.

2005-01-01

Intelligent Control and Health Management technology for aircraft propulsion systems is much more developed in the laboratory than in practice. With a renewed emphasis on reducing engine life cycle costs, improving fuel efficiency, increasing durability and life, etc., driven by various government programs, there is a strong push to move these technologies out of the laboratory and onto the engine. This paper describes the existing state of engine control and on-board health management, and surveys some specific technologies under development that will enable an aircraft propulsion system to operate in an intelligent way--defined as self-diagnostic, self-prognostic, self-optimizing, and mission adaptable. These technologies offer the potential for creating extremely safe, highly reliable systems. The technologies will help to enable a level of performance that far exceeds that of today s propulsion systems in terms of reduction of harmful emissions, maximization of fuel efficiency, and minimization of noise, while improving system affordability and safety. Technologies that are discussed include various aspects of propulsion control, diagnostics, prognostics, and their integration. The paper focuses on the improvements that can be achieved through innovative software and algorithms. It concentrates on those areas that do not require significant advances in sensors and actuators to make them achievable, while acknowledging the additional benefit that can be realized when those technologies become available. The paper also discusses issues associated with the introduction of some of the technologies.

System analysis for material control and accountancy technology

International Nuclear Information System (INIS)

Persiani, P.J.; Daly, T.A.; Bucher, R.G.; Rothman, A.B.; Cha, B.C.; Trevorrow, L.E.; Seefeldt, W.B.

1987-01-01

The systems analysis for material control and accountancy technology (SAMCAT) program involves a working group structured to ensure that direct operating measurements, accountancy experience, and knowledge of the processes and flows of nuclear material in the total US Department of Energy (DOE) complex of production fuel cycles would be the major bases for developing and implementing a plan of action. This working group consists of facility operators, DOE Office of Safeguards Security headquarters and field offices, and government laboratories. The program focus is to develop a system for decision support in validating the material control and accountancy (MC ampersand A) aspects of the masters safeguards and security agreements effectiveness and in evaluating proposed MC ampersand A upgrades. This paper is a status report on the current capabilities of the system

Analog and digital appliance technology for the control and monitoring of space HVAC systems

Energy Technology Data Exchange (ETDEWEB)

Gyoeri, M

1987-01-01

Both analog and digital devices are expected to meet the required control functions. The analog control device meets this function by way of a complicated circuitry and wiring technology of varying sophistication. In the digital control by a preprogrammed microprocessor. Digital technology allows to use the copied programme in different devices. Any change in the control of a system can be implemented and met by a programme change in digital technology. In analog technology, this change involves a change in wiring. (orig./HW).

Applying Distributed Object Technology to Distributed Embedded Control Systems

DEFF Research Database (Denmark)

Jørgensen, Bo Nørregaard; Dalgaard, Lars

2012-01-01

In this paper, we describe our Java RMI inspired Object Request Broker architecture MicroRMI for use with networked embedded devices. MicroRMI relieves the software developer from the tedious and error-prone job of writing communication protocols for interacting with such embedded devices. MicroR...... in developing control systems for distributed embedded platforms possessing severe resource restrictions.......RMI supports easy integration of high-level application specific control logic with low-level device specific control logic. Our experience from applying MicroRMI in the context of a distributed robotics control application, clearly demonstrates that it is feasible to use distributed object technology...

Control system by the technological electron Linac KUT-20

CERN Document Server

Akchurin, Y I; Gurin, V A; Demidov, N V

2001-01-01

The high-power technological electron linac KUT-20 was developed at the Science Research Complex 'Accelerator' of NSC KIPT. The linac consists of two 1.2 m length accelerating structures with a variable geometry and an injector. The latter comprises a diode electron gun,a klystron type buncher and an accelerating cavity.With a RF supply power at accelerating structure entries of 11 MW and with a current at the accelerator exit of 1A,the beam energy will be up to 20 MeV.An average beam power is planned to be 20 kW.All systems of the accelerator are controlled by a computerised control system. The program and technical complex consist of PC equipped with fast ADC control console, synchronization unit, microprocessor-operated complexes.

Air pollution control systems and technologies for waste-to-energy facilities

International Nuclear Information System (INIS)

Getz, N.P.; Amos, C.K. Jr.; Siebert, P.C.

1991-01-01

One of the primary topics of concern to those planning, developing, and operating waste-to-energy (W-T-E) [also known as municipal waste combustors (MWCs)] facilities is air emissions. This paper presents a description of the state-of-the-art air pollution control (APC) systems and technology for particulate, heavy metals, organics, and acid gases control for W-T-E facilities. Items covered include regulations, guidelines, and control techniques as applied in the W-T-E industry. Available APC technologies are viewed in detail on the basis of their potential removal efficiencies, design considerations, operations, and maintenance costs

Advanced Instrumentation, Information, and Control Systems Technologies Technical Program Plan for 2014

Energy Technology Data Exchange (ETDEWEB)

Hallbert, Bruce [Idaho National Lab. (INL), Idaho Falls, ID (United States); Thomas, Ken [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2014-07-01

The Advanced Instrumentation, Information, and Control (II&C) Systems Technologies Pathway conducts targeted research and development (R&D) to address aging and reliability concerns with the legacy instrumentation and control and related information systems of the U.S. operating light water reactor (LWR) fleet. This work involves two major goals: (1) to ensure that legacy analog II&C systems are not life-limiting issues for the LWR fleet, and (2) to implement digital II&C technology in a manner that enables broad innovation and business improvement in the nuclear power plant operating model. Resolving long-term operational concerns with the II&C systems contributes to the long-term sustainability of the LWR fleet, which is vital to the nation's energy and environmental security.

Site-specific weed control technologies

DEFF Research Database (Denmark)

Christensen, Svend; Søgaard, Henning Tangen; Kudsk, Per

2009-01-01

Site-specific weed control technologies are defined as machinery or equipment embedded with technologies that detect weeds growing in a crop and, taking into account predefined factors such as economics, takes action to maximise the chances of successfully controlling them. In the article, we...... describe the basic parts of site specific weed control technologies, comprising of weed sensing systems, weed management models and precision weed control implements. A review of state-of-the-art technologies shows that several weed sensing systems and precision implements have been developed over the last...... of knowledge about the economic and environmental potential for increasing the resolution of weed control. The integration of site-specific information on weed distribution, weed species composition and density, and the effect on crop yield, is decisive for successful site-specific weed management.   Keywords...

Systems analysis for materials control and accountancy technology

International Nuclear Information System (INIS)

Daly, T.A.; Bucher, R.G.; Rothman, A.B.; Charak, I.; Persiani, P.J.

1987-01-01

The objective is to upgrade Materials Control and Accountancy (MCandA) technology over the flows of special nuclear materials throughout the DOE complex of fuel cycles. The program focus is to develop a ''Management Tool'' for decision support in evaluating MCandA upgrades, and invalidating the MCandA aspects of the Master Safeguards and Security Agreements (MSSA) effectiveness. The approach is the computerization of the nuclear materials flow charts, identification of key measurement locations in the production and product fuel cycle, and construct data information processing at each measurement location. The program is to provide the Office of Safeguards and Security (OSS) with a timely management decision support system in planning MCandA safeguards technology upgrades over the nuclear materials production and product cycles

An assessment of advanced displays and controls technology applicable to future space transportation systems

Science.gov (United States)

Hatfield, Jack J.; Villarreal, Diana

1990-01-01

The topic of advanced display and control technology is addressed along with the major objectives of this technology, the current state of the art, major accomplishments, research programs and facilities, future trends, technology issues, space transportation systems applications and projected technology readiness for those applications. The holes that may exist between the technology needs of the transportation systems versus the research that is currently under way are addressed, and cultural changes that might facilitate the incorporation of these advanced technologies into future space transportation systems are recommended. Some of the objectives are to reduce life cycle costs, improve reliability and fault tolerance, use of standards for the incorporation of advancing technology, and reduction of weight, volume and power. Pilot workload can be reduced and the pilot's situational awareness can be improved, which would result in improved flight safety and operating efficiency. This could be accomplished through the use of integrated, electronic pictorial displays, consolidated controls, artificial intelligence, and human centered automation tools. The Orbiter Glass Cockpit Display is an example examined.

Operating experience of the automatic technological control system at the Kolsk NPP

International Nuclear Information System (INIS)

Volkov, A.P.; Ignatenko, E.I.; Kolomtsev, Yu.V.; Mel'nikov, E.F.; Trofimov, B.A.

1981-01-01

Briefly reviewed is operating experience of the automatic control systems of the kolsk NPP (KNPP) power units, where measuring technique of the neutron flux ''Iney'', ARM-4 power regulator, automatic turbine start-up system ATS are used. The main shortcomings of the technological process automatic control system (ACS) and ways of their removal are considered. It is noted that the KNPP ACS performs only limited start-up functions of the basic equipment and reactor power control as well as partially protection functions at instant loading drops and switch-off of the main circulating pump [ru

Establishment of an Environmental Control Technology Laboratory with a Circulating Fluidized-Bed Combustion System

Energy Technology Data Exchange (ETDEWEB)

Wei-Ping Pan; Yan Cao; John Smith

2008-05-31

On February 14, 2002, President Bush announced the Clear Skies Initiative, a legislative proposal to control the emissions of nitrogen oxides (NO{sub x}), sulfur dioxide (SO{sub 2}), and mercury from power plants. In response to this initiative, the National Energy Technology Laboratory organized a Combustion Technology University Alliance and hosted a Solid Fuel Combustion Technology Alliance Workshop. The workshop identified multi-pollutant control; improved sorbents and catalysts; mercury monitoring and capture; and improved understanding of the underlying reaction chemistry occurring during combustion as the most pressing research needs related to controlling environmental emissions from fossil-fueled power plants. The Environmental Control Technology Laboratory will help meet these challenges and offer solutions for problems associated with emissions from fossil-fueled power plants. The goal of this project was to develop the capability and technology database needed to support municipal, regional, and national electric power generating facilities to improve the efficiency of operation and solve operational and environmental problems. In order to effectively provide the scientific data and the methodologies required to address these issues, the project included the following aspects: (1) Establishing an Environmental Control Technology Laboratory using a laboratory-scale, simulated fluidized-bed combustion (FBC) system; (2) Designing, constructing, and operating a bench-scale (0.6 MW{sub th}), circulating fluidized-bed combustion (CFBC) system as the main component of the Environmental Control Technology Laboratory; (3) Developing a combustion technology for co-firing municipal solid waste (MSW), agricultural waste, and refuse-derived fuel (RDF) with high sulfur coals; (4) Developing a control strategy for gaseous emissions, including NO{sub x}, SO{sub 2}, organic compounds, and heavy metals; and (5) Developing new mercury capturing sorbents and new

Improving the Multi-Objective Performance of Rainwater Harvesting Systems Using Real-Time Control Technology

Directory of Open Access Journals (Sweden)

Wei D. Xu

2018-02-01

Full Text Available Many studies have identified the potential of rainwater harvesting (RWH systems to simultaneously augment potable water supply and reduce delivery of uncontrolled stormwater flows to downstream drainage networks. Potentially, such systems could also play a role in the controlled delivery of water to urban streams in ways which mimic baseflows. The performance of RWH systems to achieve these three objectives could be enhanced using Real-Time Control (RTC technology to receive rainfall forecasts and initiate pre-storm release in real time, although few studies have explored such potential. We used continuous simulation to model the ability of a range of allotment-scale RWH systems to simultaneously deliver: (i water supply; (ii stormwater retention; and (iii baseflow restoration. We compared the performance of RWH systems with RTC technology to conventional RWH systems and also systems designed with a passive baseflow release, rather than the active (RTC configuration. We found that RWH systems employing RTC technology were generally superior in simultaneously achieving water supply, stormwater retention and baseflow restoration benefits compared with the other types of system tested. The active operation provided by RTC allows the system to perform optimally across a wider range of climatic conditions, but needs to be carefully designed. We conclude that the active release mechanism employing RTC technology exhibits great promise; its ability to provide centralised control and failure detection also opens the possibility of delivering a more reliable rainwater harvesting system, which can be readily adapted to varying climate over both the short and long term.

L(sub 1) Adaptive Flight Control System: Flight Evaluation and Technology Transition

Science.gov (United States)

Xargay, Enric; Hovakimyan, Naira; Dobrokhodov, Vladimir; Kaminer, Isaac; Gregory, Irene M.; Cao, Chengyu

2010-01-01

Certification of adaptive control technologies for both manned and unmanned aircraft represent a major challenge for current Verification and Validation techniques. A (missing) key step towards flight certification of adaptive flight control systems is the definition and development of analysis tools and methods to support Verification and Validation for nonlinear systems, similar to the procedures currently used for linear systems. In this paper, we describe and demonstrate the advantages of L(sub l) adaptive control architectures for closing some of the gaps in certification of adaptive flight control systems, which may facilitate the transition of adaptive control into military and commercial aerospace applications. As illustrative examples, we present the results of a piloted simulation evaluation on the NASA AirSTAR flight test vehicle, and results of an extensive flight test program conducted by the Naval Postgraduate School to demonstrate the advantages of L(sub l) adaptive control as a verifiable robust adaptive flight control system.

The research on information security technology for the industrial control system of special equipment

International Nuclear Information System (INIS)

Chen Ligang; Liu Hongye; Zhang Wei; Sun Jianying; Lan Peng; Dai Sidan

2014-01-01

With the rapid development of information technology in enterprise application, industrial control network and management network is becoming more and more closely linked. Development and application of special equipment control system from the traditional industrial control system, not considered when designing communication security problem mainly, therefore, the industrial control system opened at the same time, isolation control system and the outside was weakened, the safety problems of industrial control system had become more and more serious. The practical application combined with the special equipment control system, analysis and elaboration in view of security problems for the control network, also, provide appropriate security solutions for professional characteristics of industrial control network, design on process control system specially, provide security partition protection scheme, in order to improve security ability of industrial control system information. (authors)

Recent Technology Advances in Distributed Engine Control

Science.gov (United States)

Culley, Dennis

2017-01-01

This presentation provides an overview of the work performed at NASA Glenn Research Center in distributed engine control technology. This is control system hardware technology that overcomes engine system constraints by modularizing control hardware and integrating the components over communication networks.

A framework for selecting suitable control technologies for nuclear power plant systems

International Nuclear Information System (INIS)

Kisner, R.A.

1992-01-01

New concepts continue to emerge for controlling systems, subsystems, and components and for monitoring parameters, characteristics, and vital signs in nuclear power plants. The steady stream of new control theories and the evolving state of control software exacerbates the difficulty of selecting the most appropriate control technology for nuclear power plant systems. As plant control room operators increase their reliance on computerized systems, the integration of monitoring, diagnostic, and control functions into a uniform and understandable environment becomes imperative. A systematic framework for comparing and evaluating the overall usefulness of control techniques is needed. This paper describes nine factors that may be used to evaluate alternative control concepts. These factors relate to a control system's potential effectiveness within the context of the overall environment, including both human and machine components. Although not an in-depth study, this paper serves to outline an evaluation framework based on several measures of utility. 32 refs

Design of Agricultural Cleaner Production Technology System

OpenAIRE

Hu, Jun-mei; Wang, Xin-jie

2009-01-01

Based on the introduction of agricultural cleaner production, technology system design of planting cleaner production is discussed from five aspects of water-saving irrigation technology, fertilization technology, diseases and insects control technology, straw comprehensive utilization technology and plastic film pollution control technology. Cleaner production technology system of livestock and poultry raise is constructed from the aspects of source control technology, reduction technique in...

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Current and advanced act control system definition study. Volume 2: Appendices

Science.gov (United States)

Hanks, G. W.; Shomber, H. A.; Dethman, H. A.; Gratzer, L. B.; Maeshiro, A.; Gangsaas, D.; Blight, J. D.; Buchan, S. M.; Crumb, C. B.; Dorwart, R. J.

1981-01-01

The current status of the Active Controls Technology (ACT) for the advanced subsonic transport project is investigated through analysis of the systems technical data. Control systems technologies under examination include computerized reliability analysis, pitch axis fly by wire actuator, flaperon actuation system design trade study, control law synthesis and analysis, flutter mode control and gust load alleviation analysis, and implementation of alternative ACT systems. Extensive analysis of the computer techniques involved in each system is included.

Hydrogen-control systems for severe LWR accident conditions - a state-of-technology report

International Nuclear Information System (INIS)

Hilliard, R.K.; Postma, A.K.; Jeppson, D.W.

1983-03-01

This report reviews the current state of technology regarding hydrogen safety issues in light water reactor plants. Topics considered in this report relate to control systems and include combustion prevention, controlled combustion, minimization of combustion effects, combination of control concepts, and post-accident disposal. A companion report addresses hydrogen generation, distribution, and combustion. The objectives of the study were to identify the key safety issues related to hydrogen produced under severe accident conditions, to describe the state of technology for each issue, and to point out ongoing programs aimed at resolving the open issues

Integrated Tools for Future Distributed Engine Control Technologies

Science.gov (United States)

Culley, Dennis; Thomas, Randy; Saus, Joseph

2013-01-01

Turbine engines are highly complex mechanical systems that are becoming increasingly dependent on control technologies to achieve system performance and safety metrics. However, the contribution of controls to these measurable system objectives is difficult to quantify due to a lack of tools capable of informing the decision makers. This shortcoming hinders technology insertion in the engine design process. NASA Glenn Research Center is developing a Hardware-inthe- Loop (HIL) platform and analysis tool set that will serve as a focal point for new control technologies, especially those related to the hardware development and integration of distributed engine control. The HIL platform is intended to enable rapid and detailed evaluation of new engine control applications, from conceptual design through hardware development, in order to quantify their impact on engine systems. This paper discusses the complex interactions of the control system, within the context of the larger engine system, and how new control technologies are changing that paradigm. The conceptual design of the new HIL platform is then described as a primary tool to address those interactions and how it will help feed the insertion of new technologies into future engine systems.

Study of fieldbus technology confiability when applied in a Sterilization plant control and safety systems

International Nuclear Information System (INIS)

Karma, D.; Sampa, M.H.O.; Rela, P.R.

2001-01-01

Several sterilization processes have been used in these years for treatment of countless products. Some processes use high temperatures, thermal shocks and chemical agents. With the discovery of the ionizing radiation and its posterior technological developments turned possible the application of that process, in 1960, also in the sterilization, denominated radiation sterilization. This process became also applied in another areas of health and industrial as food conservation, gemstones enhancement and others. The radiation sterilization requests an effective control and it needs a high level of safety. The commercial use of the computers applied in industrial automation provides and the domain of new technologies in this field provides news applications then new designs now is possible. The Fieldbus technology, a new digital communication protocol, like a Local Area Network, can be an alternative in the cobalt-60 irradiation plant. This paper show preliminary study about confiability in systems using Fieldbus technology. This technology was simulated in sterilization plant control and safety systems and the fail probability was quantified using Fail Tree Analysis Method. Fieldbus technology can be used in sterilization plants because the confiability in this systems is like PLCs and relays systems, was the conclusion

Control system technology for particle accelerators

International Nuclear Information System (INIS)

Tsumura, Yoshihiko; Matsuo, Keiichi; Maruyama, Takayuki.

1995-01-01

Control systems for particle accelerators are being designed around open-architecture systems, which allows easy upgrading, high-speed networks and high-speed processors. Mitsubishi Electric is applying realtime Unix operating systems, fiber-distributed data interface (FDDI), shared memory networks and remote I/O systems to achieve these objectives. In the area of vacuum control systems, which requires large-scale sequence control, the corporation is employing general-purpose programmable logic controllers (PLCs) to achieve cost-effective design. Software for these applications is designed around a library of application program interfaces (APIs) that give users direct access to key system functions. (author)

Environmental Control and Life Support Systems technology options for Space Station application

Science.gov (United States)

Hall, J. B., Jr.; Ferebee, M. J., Jr.; Sage, K. H.

1985-01-01

Continuous assessments regarding the suitability of candidate technologies for manned Space Stations will be needed over the next several years to obtain a basis for recommending the optimum system for an Initial Operating Capability (IOC) Space Station which is to be launched in the early 1990's. This paper has the objective to present analysis programs, the candidate recommendations, and the recommended approach for integration these candidates into the NASA Space Station reference configuration. Attention is given to ECLSS (Environmental Control and Life Support System) technology assessment program, an analysis approach for candidate technology recommendations, mission model variables, a candidate integration program, metabolic oxygen recovery, urine/flush water and all waste water recovery, wash water and condensate water recovery, and an integration analysis.

Light Water Reactor Sustainability Program Advanced Instrumentation, Information, and Control Systems Technologies Technical Program Plan for 2013

Energy Technology Data Exchange (ETDEWEB)

Hallbert, Bruce [Idaho National Laboratory (INL), Idaho Falls, ID (United States); Thomas, Ken [Idaho National Laboratory (INL), Idaho Falls, ID (United States)

2014-09-01

Reliable instrumentation, information, and control (II&C) systems technologies are essential to ensuring safe and efficient operation of the U.S. light water reactor (LWR) fleet. These technologies affect every aspect of nuclear power plant (NPP) and balance-of-plant operations. In 1997, the National Research Council conducted a study concerning the challenges involved in modernization of digital instrumentation and control systems in NPPs. Their findings identified the need for new II&C technology integration.

Controlling Complex Systems and Developing Dynamic Technology

Science.gov (United States)

Avizienis, Audrius Victor

In complex systems, control and understanding become intertwined. Following Ilya Prigogine, we define complex systems as having control parameters which mediate transitions between distinct modes of dynamical behavior. From this perspective, determining the nature of control parameters and demonstrating the associated dynamical phase transitions are practically equivalent and fundamental to engaging with complexity. In the first part of this work, a control parameter is determined for a non-equilibrium electrochemical system by studying a transition in the morphology of structures produced by an electroless deposition reaction. Specifically, changing the size of copper posts used as the substrate for growing metallic silver structures by the reduction of Ag+ from solution under diffusion-limited reaction conditions causes a dynamical phase transition in the crystal growth process. For Cu posts with edge lengths on the order of one micron, local forces promoting anisotropic growth predominate, and the reaction produces interconnected networks of Ag nanowires. As the post size is increased above 10 microns, the local interfacial growth reaction dynamics couple with the macroscopic diffusion field, leading to spatially propagating instabilities in the electrochemical potential which induce periodic branching during crystal growth, producing dendritic deposits. This result is interesting both as an example of control and understanding in a complex system, and as a useful combination of top-down lithography with bottom-up electrochemical self-assembly. The second part of this work focuses on the technological development of devices fabricated using this non-equilibrium electrochemical process, towards a goal of integrating a complex network as a dynamic functional component in a neuromorphic computing device. Self-assembled networks of silver nanowires were reacted with sulfur to produce interfacial "atomic switches": silver-silver sulfide junctions, which exhibit

Embedded Web Technology: Internet Technology Applied to Real-Time System Control

Science.gov (United States)

Daniele, Carl J.

1998-01-01

The NASA Lewis Research Center is developing software tools to bridge the gap between the traditionally non-real-time Internet technology and the real-time, embedded-controls environment for space applications. Internet technology has been expanding at a phenomenal rate. The simple World Wide Web browsers (such as earlier versions of Netscape, Mosaic, and Internet Explorer) that resided on personal computers just a few years ago only enabled users to log into and view a remote computer site. With current browsers, users not only view but also interact with remote sites. In addition, the technology now supports numerous computer platforms (PC's, MAC's, and Unix platforms), thereby providing platform independence.In contrast, the development of software to interact with a microprocessor (embedded controller) that is used to monitor and control a space experiment has generally been a unique development effort. For each experiment, a specific graphical user interface (GUI) has been developed. This procedure works well for a single-user environment. However, the interface for the International Space Station (ISS) Fluids and Combustion Facility will have to enable scientists throughout the world and astronauts onboard the ISS, using different computer platforms, to interact with their experiments in the Fluids and Combustion Facility. Developing a specific GUI for all these users would be cost prohibitive. An innovative solution to this requirement, developed at Lewis, is to use Internet technology, where the general problem of platform independence has already been partially solved, and to leverage this expanding technology as new products are developed. This approach led to the development of the Embedded Web Technology (EWT) program at Lewis, which has the potential to significantly reduce software development costs for both flight and ground software.

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Current and advanced act control system definition study, volume 1

Science.gov (United States)

Hanks, G. W.; Shomber, H. A.; Dethman, H. A.; Gratzer, L. B.; Maeshiro, A.; Gangsaas, D.; Blight, J. D.; Buchan, S. M.; Crumb, C. B.; Dorwart, R. J.

1981-01-01

An active controls technology (ACT) system architecture was selected based on current technology system elements and optimal control theory was evaluated for use in analyzing and synthesizing ACT multiple control laws. The system selected employs three redundant computers to implement all of the ACT functions, four redundant smaller computers to implement the crucial pitch-augmented stability function, and a separate maintenance and display computer. The reliability objective of probability of crucial function failure of less than 1 x 10 to the -9th power per flight of 1 hr can be met with current technology system components, if the software is assumed fault free and coverage approaching 1.0 can be provided. The optimal control theory approach to ACT control law synthesis yielded comparable control law performance much more systematically and directly than the classical s-domain approach. The ACT control law performance, although somewhat degraded by the inclusion of representative nonlinearities, remained quite effective. Certain high-frequency gust-load alleviation functions may require increased surface rate capability.

Advanced Instrumentation, Information, and Control Systems Technologies Research in Support of Light Water Reactors

International Nuclear Information System (INIS)

Hallbert, Bruce P.; Kenneth, Thomas

2014-01-01

The Advanced Instrumentation, Information, and Control (II and C) Systems Technologies Pathway conducts targeted research and development (R and D) to address aging and reliability concerns with the legacy instrumentation and control and related information systems of the U.S. operating light water reactor (LWR) fleet. This work involves two major goals to ensure that legacy analog II and C systems are not life-limiting issues for the LWR fleet, and to implement digital II and C technology in a manner that enables broad innovation and business improvement in the nuclear power plant operating model. Resolving long-term operational concerns with the II and C systems contributes to the long-term sustainability of the LWR fleet, which is vital to the nation's energy and environmental security

Advanced Instrumentation, Information, and Control Systems Technologies Research in Support of Light Water Reactors

Energy Technology Data Exchange (ETDEWEB)

Hallbert, Bruce P.; Kenneth, Thomas [Idaho National Laboratory, Idaho (United States)

2014-08-15

The Advanced Instrumentation, Information, and Control (II and C) Systems Technologies Pathway conducts targeted research and development (R and D) to address aging and reliability concerns with the legacy instrumentation and control and related information systems of the U.S. operating light water reactor (LWR) fleet. This work involves two major goals to ensure that legacy analog II and C systems are not life-limiting issues for the LWR fleet, and to implement digital II and C technology in a manner that enables broad innovation and business improvement in the nuclear power plant operating model. Resolving long-term operational concerns with the II and C systems contributes to the long-term sustainability of the LWR fleet, which is vital to the nation's energy and environmental security.

Evaluation of information technology impact on effective internal control in the University system

Energy Technology Data Exchange (ETDEWEB)

Sanusi Fasilat, A., E-mail: Fasilat17@gmail.com; Hassan, Haslinda, E-mail: lynn@uum.edu.my [School of Accountancy, College of Business, Universiti Utara Malaysia, Sintok, Kedah (Malaysia)

2015-12-11

Information Technology (IT) plays a key role in internal control system in various organizations in terms of maintaining records and other internal services. Internal control system is defined as an efficient control procedures set up by firm to safeguard resources and to assure the reliability and accuracy of both financial and non-financial records in line with applicable governance and procedure to acquire the established goal and objectives. This paper focuses on the impact of IT on internal control system in the Nigerian universities. Data are collected from three different universities via questionnaire. Descriptive statistics is used to analyze the data; Chi-square is performed to test the hypothesis. The results of the hypothesis showed that IT has a positive relationship with the effective internal control activities in the University system. It is concluded that the adoption of IT will significantly improve the effectiveness of the internal control system operations in the University in terms of quality service delivery.

Evaluation of information technology impact on effective internal control in the University system

International Nuclear Information System (INIS)

Sanusi Fasilat, A.; Hassan, Haslinda

2015-01-01

Information Technology (IT) plays a key role in internal control system in various organizations in terms of maintaining records and other internal services. Internal control system is defined as an efficient control procedures set up by firm to safeguard resources and to assure the reliability and accuracy of both financial and non-financial records in line with applicable governance and procedure to acquire the established goal and objectives. This paper focuses on the impact of IT on internal control system in the Nigerian universities. Data are collected from three different universities via questionnaire. Descriptive statistics is used to analyze the data; Chi-square is performed to test the hypothesis. The results of the hypothesis showed that IT has a positive relationship with the effective internal control activities in the University system. It is concluded that the adoption of IT will significantly improve the effectiveness of the internal control system operations in the University in terms of quality service delivery

Evaluation of information technology impact on effective internal control in the University system

Science.gov (United States)

Sanusi Fasilat, A.; Hassan, Haslinda

2015-12-01

Information Technology (IT) plays a key role in internal control system in various organizations in terms of maintaining records and other internal services. Internal control system is defined as an efficient control procedures set up by firm to safeguard resources and to assure the reliability and accuracy of both financial and non-financial records in line with applicable governance and procedure to acquire the established goal and objectives. This paper focuses on the impact of IT on internal control system in the Nigerian universities. Data are collected from three different universities via questionnaire. Descriptive statistics is used to analyze the data; Chi-square is performed to test the hypothesis. The results of the hypothesis showed that IT has a positive relationship with the effective internal control activities in the University system. It is concluded that the adoption of IT will significantly improve the effectiveness of the internal control system operations in the University in terms of quality service delivery.

Use of Soft Computing Technologies for a Qualitative and Reliable Engine Control System for Propulsion Systems

Science.gov (United States)

Trevino, Luis; Brown, Terry; Crumbley, R. T. (Technical Monitor)

2001-01-01

The problem to be addressed in this paper is to explore how the use of Soft Computing Technologies (SCT) could be employed to improve overall vehicle system safety, reliability, and rocket engine performance by development of a qualitative and reliable engine control system (QRECS). Specifically, this will be addressed by enhancing rocket engine control using SCT, innovative data mining tools, and sound software engineering practices used in Marshall's Flight Software Group (FSG). The principle goals for addressing the issue of quality are to improve software management, software development time, software maintenance, processor execution, fault tolerance and mitigation, and nonlinear control in power level transitions. The intent is not to discuss any shortcomings of existing engine control methodologies, but to provide alternative design choices for control, implementation, performance, and sustaining engineering, all relative to addressing the issue of reliability. The approaches outlined in this paper will require knowledge in the fields of rocket engine propulsion (system level), software engineering for embedded flight software systems, and soft computing technologies (i.e., neural networks, fuzzy logic, data mining, and Bayesian belief networks); some of which are briefed in this paper. For this effort, the targeted demonstration rocket engine testbed is the MC-1 engine (formerly FASTRAC) which is simulated with hardware and software in the Marshall Avionics & Software Testbed (MAST) laboratory that currently resides at NASA's Marshall Space Flight Center, building 4476, and is managed by the Avionics Department. A brief plan of action for design, development, implementation, and testing a Phase One effort for QRECS is given, along with expected results. Phase One will focus on development of a Smart Start Engine Module and a Mainstage Engine Module for proper engine start and mainstage engine operations. The overall intent is to demonstrate that by

Hybrid control rooms: the effects of introducing new technology into existing control rooms

International Nuclear Information System (INIS)

Morisseau, Dolores S.

2001-02-01

The goal of this part of the Hybrid Control Room Project is to gain a perspective on the issues and problems that are an integral part of introducing new technology, automated systems, or support systems into nuclear power plant (NPP) control rooms, particularly when they are introduced on a system-by-system basis. For purposes of this project, hybrid control rooms are defined as those into which new technology, such as digital and computer-based controls are gradually incorporated as opposed to those that are completely, or nearly completely, refitted with new technology. Although the focus of this project is the introduction of computer based, digital systems into NPP control rooms, it is not possible to exclude the effects throughout the process that are inevitable when new technology is introduced anywhere in complex process control systems. Thus, this document examines the effects of such changes within the context of the organisation in which they occur, including the management of change, work procedures and work methods, communications and crew interaction, training, and the interdependent functions in the operational context. (Author)

Nutrition and food technology for a Controlled Ecological Life Support System (CELSS)

Science.gov (United States)

Glaser, P. E.; Mabel, J. A.

1981-01-01

Food technology requirements and a nutritional strategy for a Controlled Ecological Life Support System (CELSS) to provide adequate food in an acceptable form in future space missions are discussed. The establishment of nutritional requirements, dietary goals, and a food service system to deliver acceptable foods in a safe and healthy form and the development of research goals and priorities were the main objectives of the study.

Fiscal 1999 achievement report. Research and technology of important regional technologies (Development of combustion control system technology for rationalizing energy use); 1999 nendo energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For upgrading and optimizing combustion control systems, research and development is conducted for materializing SiC devices capable of high-temperature operation. In the development of basic technologies common to various types of SiC semiconductor devices, XeCl excimer laser annealing is applied to SiC implanted with Al ions, and low-damage ion implantation is studied. In the development of techniques for forming SiC single crystals into substrates, warpage of 20{mu} or less, surface coarseness of 5{mu}m or less, etc., are achieved in 1-inch and 2-inch wafers. In the development of SiC sensor technology, techniques of heteroepitaxial growth of 3C-SiC on Si substrates and of 6H-SiC on 6H-SiC wafers are established and an optical sensor is built experimentally. A high-temperature UV sensor, switching device for control, rectification device for control, etc., are built of nitrogen ion implanted 6H-SiC. In the effort to develop combustion control system technology, the principle of system operation of the combustion control method proposed under this project is verified. (NEDO)

Fly-by-light flight control system technology development plan

Science.gov (United States)

Chakravarty, A.; Berwick, J. W.; Griffith, D. M.; Marston, S. E.; Norton, R. L.

1990-01-01

The results of a four-month, phased effort to develop a Fly-by-Light Technology Development Plan are documented. The technical shortfalls for each phase were identified and a development plan to bridge the technical gap was developed. The production configuration was defined for a 757-type airplane, but it is suggested that the demonstration flight be conducted on the NASA Transport Systems Research Vehicle. The modifications required and verification and validation issues are delineated in this report. A detailed schedule for the phased introduction of fly-by-light system components has been generated. It is concluded that a fiber-optics program would contribute significantly toward developing the required state of readiness that will make a fly-by-light control system not only cost effective but reliable without mitigating the weight and high-energy radio frequency related benefits.

Output Control Technologies for a Large-scale PV System Considering Impacts on a Power Grid

Science.gov (United States)

Kuwayama, Akira

The mega-solar demonstration project named “Verification of Grid Stabilization with Large-scale PV Power Generation systems” had been completed in March 2011 at Wakkanai, the northernmost city of Japan. The major objectives of this project were to evaluate adverse impacts of large-scale PV power generation systems connected to the power grid and develop output control technologies with integrated battery storage system. This paper describes the outline and results of this project. These results show the effectiveness of battery storage system and also proposed output control methods for a large-scale PV system to ensure stable operation of power grids. NEDO, New Energy and Industrial Technology Development Organization of Japan conducted this project and HEPCO, Hokkaido Electric Power Co., Inc managed the overall project.

Light Water Reactor Sustainability Program Advanced Instrumentation, Information, and Control Systems Technologies Technical Program Plan for FY 2016

Energy Technology Data Exchange (ETDEWEB)

Hallbert, Bruce Perry [Idaho National Lab. (INL), Idaho Falls, ID (United States); Thomas, Kenneth David [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-10-01

Reliable instrumentation, information, and control (II&C) systems technologies are essential to ensuring safe and efficient operation of the U.S. light water reactor (LWR) fleet. These technologies affect every aspect of nuclear power plant (NPP) and balance-of-plant operations. In 1997, the National Research Council conducted a study concerning the challenges involved in modernization of digital instrumentation and control systems in NPPs. Their findings identified the need for new II&C technology integration.

12. Kassel symposium of power system engineering - control technology for decentral power supply systems. Proceedings; Zwoelftes Kasseler Symposium Energie-Systemtechnik - Regelungstechnik fuer dezentrale Energiesysteme. Tagungsband

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

The 12. Kassel symposium of power system engineering focused on control technology for decentral power generation systems. It addressed experts of mechanical engineering, electrical engineering, control engineering and related fields. The symposium was to provide a picture of the state of the art of selected control systems and also to illustrate the immportance of control technology for these systems. Most of the papers used the example of large-capacity wind power systems, where the interdependence of mechanical and electrical engineering and the importance of control technology are particularly clear. The selected illustrate the interdisciplinary character of this engineering discipline, which is also the element that makes it so very interesting. The Kassel symposium therefore addressed not only experts but also students of these disciplines who want to find out more about the theory and practice of renewable power systems. (orig.)

Technologies for Legionella Control

Science.gov (United States)

Presentation includes a review of new Office of Water document entitled "Technologies for Legionella Control in Premise Plumbing Systems", and discussion on ORD research projects involving Legionella and disinfection.

Technological and life cycle assessment of organics processing odour control technologies

Energy Technology Data Exchange (ETDEWEB)

Bindra, Navin [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada); Dubey, Brajesh, E-mail: bkdubey@civil.iitkgp.ernet.in [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada); Environmental Engineering Division, Department of Civil Engineering, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India); Dutta, Animesh [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada)

2015-09-15

As more municipalities and communities across developed world look towards implementing organic waste management programmes or upgrading existing ones, composting facilities are emerging as a popular choice. However, odour from these facilities continues to be one of the most important concerns in terms of cost & effective mitigation. This paper provides a technological and life cycle assessment of some of the different odour control technologies and treatment methods that can be implemented in organics processing facilities. The technological assessment compared biofilters, packed tower wet scrubbers, fine mist wet scrubbers, activated carbon adsorption, thermal oxidization, oxidization chemicals and masking agents. The technologies/treatment methods were evaluated and compared based on a variety of operational, usage and cost parameters. Based on the technological assessment it was found that, biofilters and packed bed wet scrubbers are the most applicable odour control technologies for use in organics processing faculties. A life cycle assessment was then done to compare the environmental impacts of the packed-bed wet scrubber system, organic (wood-chip media) bio-filter and inorganic (synthetic media) bio-filter systems. Twelve impact categories were assessed; cumulative energy demand (CED), climate change, human toxicity, photochemical oxidant formation, metal depletion, fossil depletion, terrestrial acidification, freshwater eutrophication, marine eutrophication, terrestrial eco-toxicity, freshwater eco-toxicity and marine eco-toxicity. The results showed that for all impact categories the synthetic media biofilter had the highest environmental impact, followed by the wood chip media bio-filter system. The packed-bed system had the lowest environmental impact for all categories. - Highlights: • Assessment of odour control technologies for organics processing facilities. • Comparative life cycle assessment of three odour control technologies was conducted

Key technologies of the server monitor and control system based on GSM short messages

International Nuclear Information System (INIS)

Chen Taiwei; Zhou Zhenliu; Liu Baoxu

2007-01-01

The network management based on SNMP protocol cannot effectively monitor and control application-system states and key-process states on the computer server. Furthermore, it needs the administrator's longtime surveillance. When the administrator leaves the computer, he can't receive the malfunction message in time. In this paper we present a server monitor and control system based on monitor agents and GSM short messages, introduce the key technology to realize it, and implement a model system in the real network environment. (authors)

Report from the Light Water Reactor Sustainability Workshop on Advanced Instrumentation, Information, and Control Systems and Human-System Interface Technologies

International Nuclear Information System (INIS)

Hallbert, Bruce P.; Persensky, J.J.; Smidts, Carol; Aldemir, Tunc; Naser, Joseph

2009-01-01

The Light Water Reactor Sustainability (LWRS) Program is a research and development (R and D) program sponsored by the U.S. Department of Energy (DOE). The program is operated in close collaboration with industry R and D programs to provide the technical foundations for licensing and managing the long-term, safe, and economical operation of Nuclear Power Plants that are currently in operation. The LWRS Program focus is on longer-term and higher-risk/reward research that contributes to the national policy objectives of energy and environmental security. Advanced instruments and control (I and C) technologies are needed to support the safe and reliable production of power from nuclear energy systems during sustained periods of operation up to and beyond their expected licensed lifetime. This requires that new capabilities to achieve process control be developed and eventually implemented in existing nuclear assets. It also requires that approaches be developed and proven to achieve sustainability of I and C systems throughout the period of extended operation. The strategic objective of the LWRS Program Advanced Instrumentation, Information, and Control Systems Technology R and D pathway is to establish a technical basis for new technologies needed to achieve safety and reliability of operating nuclear assets and to implement new technologies in nuclear energy systems. This will be achieved by carrying out a program of R and D to develop scientific knowledge in the areas of: (1) Sensors, diagnostics, and prognostics to support characterization and prediction of the effects of aging and degradation phenomena effects on critical systems, structures, and components (SSCs); (2) Online monitoring of SSCs and active components, generation of information, and methods to analyze and employ online monitoring information; (3) New methods for visualization, integration, and information use to enhance state awareness and leverage expertise to achieve safer, more readily available

Report from the Light Water Reactor Sustainability Workshop on Advanced Instrumentation, Information, and Control Systems and Human-System Interface Technologies

Energy Technology Data Exchange (ETDEWEB)

Bruce P. Hallbert; J. J. Persensky; Carol Smidts; Tunc Aldemir; Joseph Naser

2009-08-01

The Light Water Reactor Sustainability (LWRS) Program is a research and development (R&D) program sponsored by the U.S. Department of Energy (DOE). The program is operated in close collaboration with industry R&D programs to provide the technical foundations for licensing and managing the long-term, safe, and economical operation of Nuclear Power Plants that are currently in operation. The LWRS Program focus is on longer-term and higher-risk/reward research that contributes to the national policy objectives of energy and environmental security. Advanced instruments and control (I&C) technologies are needed to support the safe and reliable production of power from nuclear energy systems during sustained periods of operation up to and beyond their expected licensed lifetime. This requires that new capabilities to achieve process control be developed and eventually implemented in existing nuclear assets. It also requires that approaches be developed and proven to achieve sustainability of I&C systems throughout the period of extended operation. The strategic objective of the LWRS Program Advanced Instrumentation, Information, and Control Systems Technology R&D pathway is to establish a technical basis for new technologies needed to achieve safety and reliability of operating nuclear assets and to implement new technologies in nuclear energy systems. This will be achieved by carrying out a program of R&D to develop scientific knowledge in the areas of: • Sensors, diagnostics, and prognostics to support characterization and prediction of the effects of aging and degradation phenomena effects on critical systems, structures, and components (SSCs) • Online monitoring of SSCs and active components, generation of information, and methods to analyze and employ online monitoring information • New methods for visualization, integration, and information use to enhance state awareness and leverage expertise to achieve safer, more readily available electricity generation

Protection and Control with FPGA technology

Energy Technology Data Exchange (ETDEWEB)

Sohn, K. Y.; Yi, W. J. [Korea Reliability Technology and System, Daejeon (Korea, Republic of); Koo, I. S. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2012-03-15

To cope with the experiences such as unsatisfied response time of control and protection system, components obsolescence of those systems, and outstanding coercion of system modernization, nuclear society is striving to resolve this issue fundamentally. The reports and standards issued from IAEA and other standard organization like IBC is interested in the FPGA technology, which is fairly mature technology in other fields of industry. Intuitively it is replacing the high level of micro-processor type equipped with various software and hardware, which causes to accelerate the aging and obsolescence, and demands for system modernization in I and C system in Nuclear Power Plant. Thus utility has to spend much time and effort to upgrade I and C system throughout a decease. This paper summarizes the need of FPGA technology in Nuclear Power Plant, describing the characteristics of FPGA, test methodology and design requirements. Also the specific design and implementation experiences brought up in the course of FPGA-based controller, which has been conducted in KoRTS. The certification and verification and validation process to ensure the integrity of FPGA-based controller will be addressed. After that, Diverse Protection System (DPS) for YGN Unit 3 and 4 that is implemented via VHDL through SDLC is loaded on FPGA-based controller for run-time experimentations such as functionality, performance, integrity and reliability. Some of the test data is addressed in this paper.

Protection and Control with FPGA technology

International Nuclear Information System (INIS)

Sohn, K. Y.; Yi, W. J.; Koo, I. S.

2012-01-01

To cope with the experiences such as unsatisfied response time of control and protection system, components obsolescence of those systems, and outstanding coercion of system modernization, nuclear society is striving to resolve this issue fundamentally. The reports and standards issued from IAEA and other standard organization like IBC is interested in the FPGA technology, which is fairly mature technology in other fields of industry. Intuitively it is replacing the high level of micro-processor type equipped with various software and hardware, which causes to accelerate the aging and obsolescence, and demands for system modernization in I and C system in Nuclear Power Plant. Thus utility has to spend much time and effort to upgrade I and C system throughout a decease. This paper summarizes the need of FPGA technology in Nuclear Power Plant, describing the characteristics of FPGA, test methodology and design requirements. Also the specific design and implementation experiences brought up in the course of FPGA-based controller, which has been conducted in KoRTS. The certification and verification and validation process to ensure the integrity of FPGA-based controller will be addressed. After that, Diverse Protection System (DPS) for YGN Unit 3 and 4 that is implemented via VHDL through SDLC is loaded on FPGA-based controller for run-time experimentations such as functionality, performance, integrity and reliability. Some of the test data is addressed in this paper

Research and development on the application of advanced control technologies to advanced nuclear reactor systems: A US national perspective

International Nuclear Information System (INIS)

White, J.D.; Monson, L.R.; Carrol, D.G.; Dayal, Y.

1989-01-01

Control system designs for nuclear power plants are becoming more advanced through the use of digital technology and automation. This evolution is taking place because of: (1) the limitations in analog based control system performance and maintenance and availability and (2) the promise of significant improvement in plant operation and availability due to advances in digital and other control technologies. Digital retrofits of control systems in US nuclear plants are occurring now. Designs of control and protection systems for advanced LWRs are based on digital technology. The use of small inexpensive, fast, large-capacity computers in these designs is the first step of an evolutionary process described in this paper. Under the sponsorship of the US Department of Energy (DOE), Oak Ridge National Laboratory, Argonne National Laboratory, GE Nuclear Energy and several universities are performing research and development in the application of advances in control theory, software engineering, advanced computer architectures, artificial intelligence, and man-machine interface analysis to control system design. The target plant concept for the work described in this paper is the Power Reactor Inherently Safe Module reactor (PRISM), an advanced modular liquid metal reactor concept. This and other reactor designs which provide strong passive responses to operational upsets or accidents afford good opportunities to apply these advances in control technology. 18 refs., 5 figs

Automatic start-up system of nuclear reactor based on sequence control technology

International Nuclear Information System (INIS)

Zhang Yao; Zhang Dafa; Peng Huaqing

2009-01-01

A conceptive design of an automatic start-up system based on the sequence control for the nuclear reactors is given in this paper, so as to solve the problems during the start-up process, such as the long operation time, low automatic control level and high accident rate. The start-up process and its requirements are analyzed in detail at first. Then,the principle, the architecture, the key technologies of the automatic start-up system of nuclear reactors are designed and discussed. With the designed system, the automatic start-up of the nuclear reactor can be realized,the work load of the operator can be reduced,and the safety and efficiency of the nuclear power plant during its start-up can be improved. (authors)

Parent Perception of Two Eye-Gaze Control Technology Systems in Young Children with Cerebral Palsy: Pilot Study.

Science.gov (United States)

Karlsson, Petra; Wallen, Margaret

2017-01-01

Eye-gaze control technology enables people with significant physical disability to access computers for communication, play, learning and environmental control. This pilot study used a multiple case study design with repeated baseline assessment and parents' evaluations to compare two eye-gaze control technology systems to identify any differences in factors such as ease of use and impact of the systems for their young children. Five children, aged 3 to 5 years, with dyskinetic cerebral palsy, and their families participated. Overall, families were satisfied with both the Tobii PCEye Go and myGaze® eye tracker, found them easy to position and use, and children learned to operate them quickly. This technology provides young children with important opportunities for learning, play, leisure, and developing communication.

Report on achievements of research and development of an automatic sewing system in fiscal 1986. System management and control technology; 1986 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. System kanri seigyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-01

The Automatic Sewing System Technology Research Association was commissioned from the Agency of Industrial Science and Technology on the 'development of an automatic sewing system'. The association is performing the research and development by dividing the subject into such component technologies as a total system and sewing preparation and processing technology, a sewing and assembling technology, a cloth handling technology, and a system management and control technology. This paper reports the achievement of the research and development on the system management and control technology. Plans have been established on the following items: dimensional inspection of sewn parts by using an image processing technology, real-time processing of the matching work interlocked with a striped pattern cloth handling device, and a processing positioning algorithm to instruct sewing lines and needle dropping points based on contour lines of pockets and collars. The effects thereof were verified. Printing seven-segmented numerals on cloth by using fluorescent whitener and an automatic reading test of the printed information verified that the technology can be applied to tracking the parts in a processing line as an ID information. Researches were also made on unification of micro-computers for controlling such automatic machines as a multi-functional sewing machine, a three-dimensional sewing machine, and a cloth handling and positioning device, as well as on interface with the computer for function sharing management and control. (NEDO)

Report on achievements of research and development of an automatic sewing system in fiscal 1986. System management and control technology; 1986 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. System kanri seigyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-01

The Automatic Sewing System Technology Research Association was commissioned from the Agency of Industrial Science and Technology on the 'development of an automatic sewing system'. The association is performing the research and development by dividing the subject into such component technologies as a total system and sewing preparation and processing technology, a sewing and assembling technology, a cloth handling technology, and a system management and control technology. This paper reports the achievement of the research and development on the system management and control technology. Plans have been established on the following items: dimensional inspection of sewn parts by using an image processing technology, real-time processing of the matching work interlocked with a striped pattern cloth handling device, and a processing positioning algorithm to instruct sewing lines and needle dropping points based on contour lines of pockets and collars. The effects thereof were verified. Printing seven-segmented numerals on cloth by using fluorescent whitener and an automatic reading test of the printed information verified that the technology can be applied to tracking the parts in a processing line as an ID information. Researches were also made on unification of micro-computers for controlling such automatic machines as a multi-functional sewing machine, a three-dimensional sewing machine, and a cloth handling and positioning device, as well as on interface with the computer for function sharing management and control. (NEDO)

Design of coordinated controller in nuclear power plant based on digital instrument and control technology

International Nuclear Information System (INIS)

Cheng Shouyu; Peng Minjun; Liu Xinkai; Zhao Qiang; Deng Xiangxin

2014-01-01

Nuclear power plant (NPP) is a multi-input and multi-output, no-linear and time-varying complex system. The conventional PID controller is usually used in NPP control system which is based on analog instrument. The system parameters are easy to overshoot and the response time is longer in the control mode of the conventional PID. In order to improve this condition, a new coordinated control strategy which is based on expert system and the original controllers in the digital instrument and control technology was presented. In order to verify and validate it, the proposed coordinated control technology was tested by the full-scope real-time simulation system. The results prove that using digital instrument and control technology to achieve coordinated controller is feasible, the coordinated controller can effectively improve the dynamic operating characteristics of the system, and the coordinated controller is superior to the conventional PID controller in control performance. (authors)

PFGA based, full-duplex, multi-channel, optical gigabit, synchronous data transceiver for TESLA technology LLRF control system

Energy Technology Data Exchange (ETDEWEB)

Pozniak, K.T.; Romaniuk, R.S.; Jalmuzna, W.; Olowski, K.; Perkuszewski, K.; Zielinski, J. [Warsaw Univ. of Technology (Poland). Inst. of Electronic Systems; Kierzkowski, K. [Warsaw Univ. (Poland). Inst. of Experimental Physics

2005-07-01

It may be predicted now, even assuming very conservative approach, that the next generation of the Low Level RF control systems for future accelerators will use extensively such technologies like: very fast programmable circuits equipped with DSP, embedded PC and optical communication I/O functionalities, as well as multi-gigabit optical transmission of measurement data and control signals. The paper presents the idea and realization of a gigabit synchronous data distributor designed to work in the LLRF control system of TESLA technology based X-ray FEL. The design bases on a relatively simple and cheap FPGA chip Cyclone. Commercially available SERDES (serializer/deserializer) and optical transceiver chips were applied. The optoelectronic module is embedded on the main LLRF BMB (backbone mother board). The MB provides communication with the outside computer control system, programmable chip configuration, integration with other functional modules and power supply. The hardware implementation is here described and the used software for BER (bit-error-rate) testing of the multi-gigabit optical link. The measurement results are presented. The appendix contains a comparison between the available protocols of serial data transmission for FPGA technology. This TESLA Technology Report is a partial contribution to the next version of the SIMCON system which is expected to be released this year. The SIMCON, ver 3. will contain 8 channels and multi-gigabit optical transmission capability. (orig.)

Control Technologies for Room Air-conditioner and Packaged Air-conditioner

Science.gov (United States)

Ito, Nobuhisa

Trends of control technologies about air-conditioning machineries, especially room or packaged air conditioners, are presented in this paper. Multiple air conditioning systems for office buildings are mainly described as one application of the refrigeration cycle control technologies including sensors for thermal comfort and heating/ cooling loads are also described as one of the system control technologies. Inverter systems and related technologies for driving variable speed compressors are described in both case of including induction motors and brushless DC motors. Technologies for more accurate control to meet various kind of regulations such as ozone layer destruction, energy saving and global warming, and for eliminating harmonic distortion of power source current, as a typical EMC problem, will be urgently desired.

TESLA cavity modeling and digital implementation in FPGA technology for control system development

International Nuclear Information System (INIS)

Czarski, T.; Pozniak, K.T.; Romaniuk, R.S.; Simrock, S.

2006-01-01

The electromechanical model of the TESLA cavity has been implemented in FPGA technology for real-time testing of the control system. The model includes Lorentz force detuning and beam loading effects. Step operation and vector stimulus operation modes are applied for the evaluation of a FPGA cavity simulator operated by a digital controller. The performance of the cavity hardware model is verified by comparing with a software model of the cavity implemented in the MATLAB system. The numerical aspects are considered for an optimal DSP calculation. Some experimental results are presented for different cavity operational conditions. (orig.)

Greenhouse irrigation control system design based on ZigBee and fuzzy PID technology

Science.gov (United States)

Zhou, Bing; Yang, Qiliang; Liu, Kenan; Li, Peiqing; Zhang, Jing; Wang, Qijian

In order to achieve the water demand information accurately detect of the greenhouse crop and its precision irrigation automatic control, this article has designed a set of the irrigated control system based on ZigBee and fuzzy PID technology, which composed by the soil water potential sensor, CC2530F256 wireless microprocessor, IAR Embedded Workbench software development platform. And the time of Irrigation as the output .while the amount of soil water potential and crop growth cycle as the input. The article depended on Greenhouse-grown Jatropha to verify the object, the results show that the system can irrigate timely and appropriately according to the soil water potential and water demend of the different stages of Jatropha growth , which basically meet the design requirements. Therefore, the system has broad application prospects in the amount of greenhouse crop of fine control irrigation.

Control System Architectures, Technologies and Concepts for Near Term and Future Human Exploration of Space

Science.gov (United States)

Boulanger, Richard; Overland, David

2004-01-01

Technologies that facilitate the design and control of complex, hybrid, and resource-constrained systems are examined. This paper focuses on design methodologies, and system architectures, not on specific control methods that may be applied to life support subsystems. Honeywell and Boeing have estimated that 60-80Y0 of the effort in developing complex control systems is software development, and only 20-40% is control system development. It has also been shown that large software projects have failure rates of as high as 50-65%. Concepts discussed include the Unified Modeling Language (UML) and design patterns with the goal of creating a self-improving, self-documenting system design process. Successful architectures for control must not only facilitate hardware to software integration, but must also reconcile continuously changing software with much less frequently changing hardware. These architectures rely on software modules or components to facilitate change. Architecting such systems for change leverages the interfaces between these modules or components.

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transpot project-demonstration act system definition

Science.gov (United States)

Hanks, G. W.; Shomber, H. A.; Crumb, C. B.; Flora, C. C.; Macdonald, K. A. B.; Smith, R. D.; Sassi, A. P.; Dorwart, R. J.

1982-01-01

The 1985 ACT airplane is the Final Active Controls Technology (ACT) Airplane with the addition of three-axis fly by wire. Thus it retains all the efficiency features of the full ACT system plus the weight and cost savings accruing from deletion of the mechanical control system. The control system implements the full IAAC spectrum of active controls except flutter-mode control, judged essentially nonbeneficial, and incorporates new control surfaces called flaperons to make the most of wing-load alleviation. This redundant electronic system is conservatively designed to preserve the extreme reliability required of crucial short-period pitch augmentation, which provides more than half of the fuel savings.

Research on NC motion controller based on SOPC technology

Science.gov (United States)

Jiang, Tingbiao; Meng, Biao

2006-11-01

With the rapid development of the digitization and informationization, the application of numerical control technology in the manufacturing industry becomes more and more important. However, the conventional numerical control system usually has some shortcomings such as the poor in system openness, character of real-time, cutability and reconfiguration. In order to solve these problems, this paper investigates the development prospect and advantage of the application in numerical control area with system-on-a-Programmable-Chip (SOPC) technology, and puts forward to a research program approach to the NC controller based on SOPC technology. Utilizing the characteristic of SOPC technology, we integrate high density logic device FPGA, memory SRAM, and embedded processor ARM into a single programmable logic device. We also combine the 32-bit RISC processor with high computing capability of the complicated algorithm with the FPGA device with strong motivable reconfiguration logic control ability. With these steps, we can greatly resolve the defect described in above existing numerical control systems. For the concrete implementation method, we use FPGA chip embedded with ARM hard nuclear processor to construct the control core of the motion controller. We also design the peripheral circuit of the controller according to the requirements of actual control functions, transplant real-time operating system into ARM, design the driver of the peripheral assisted chip, develop the application program to control and configuration of FPGA, design IP core of logic algorithm for various NC motion control to configured it into FPGA. The whole control system uses the concept of modular and structured design to develop hardware and software system. Thus the NC motion controller with the advantage of easily tailoring, highly opening, reconfigurable, and expandable can be implemented.

Information technology equipment cooling system

Science.gov (United States)

Schultz, Mark D.

2014-06-10

According to one embodiment, a system for removing heat from a rack of information technology equipment may include a sidecar indoor air to liquid heat exchanger that cools warm air generated by the rack of information technology equipment. The system may also include a liquid to liquid heat exchanger and an outdoor heat exchanger. The system may further include configurable pathways to connect and control fluid flow through the sidecar heat exchanger, the liquid to liquid heat exchanger, the rack of information technology equipment, and the outdoor heat exchanger based upon ambient temperature and/or ambient humidity to remove heat from the rack of information technology equipment.

Control system in the technological electron linacs

International Nuclear Information System (INIS)

Boriskin, V.N.; Akchurin, Yu.I.; Bahmetev, N.N.; Gurin, V.A.

1999-01-01

The special system has been developed for linac control.It controls the electron beam current,the energy and the position,protects the accelerating and scanning systems from the damage caused by the beam;blocks the modulator and the klystron amplifier in the case of intolerable operating modes;regulates the phase and power of the HF signals in the injecting system and also regulates the source power currents in the magnetic system

Zigbee networking technology and its application in Lamost optical fiber positioning and control system

Science.gov (United States)

Jin, Yi; Zhai, Chao; Gu, Yonggang; Zhou, Zengxiang; Gai, Xiaofeng

2010-07-01

4,000 fiber positioning units need to be positioned precisely in LAMOST(Large Sky Area Multi-object Optical Spectroscopic Telescope) optical fiber positioning & control system, and every fiber positioning unit needs two stepper motors for its driven, so 8,000 stepper motors need to be controlled in the entire system. Wireless communication mode is adopted to save the installing space on the back of the focal panel, and can save more than 95% external wires compared to the traditional cable control mode. This paper studies how to use the ZigBee technology to group these 8000 nodes, explores the pros and cons of star network and tree network in order to search the stars quickly and efficiently. ZigBee technology is a short distance, low-complexity, low power, low data rate, low-cost two-way wireless communication technology based on the IEEE 802.15.4 protocol. It based on standard Open Systems Interconnection (OSI): The 802.15.4 standard specifies the lower protocol layers-the physical layer (PHY), and the media access control (MAC). ZigBee Alliance defined on this basis, the rest layers such as the network layer and application layer, and is responsible for high-level applications, testing and marketing. The network layer used here, based on ad hoc network protocols, includes the following functions: construction and maintenance of the topological structure, nomenclature and associated businesses which involves addressing, routing and security and a self-organizing-self-maintenance functions which will minimize consumer spending and maintenance costs. In this paper, freescale's 802.15.4 protocol was used to configure the network layer. A star network and a tree network topology is realized, which can build network, maintenance network and create a routing function automatically. A concise tree network address allocate algorithm is present to assign the network ID automatically.

Assessing the interaction effect of cost control systems and information technology integration on manufacturing plant financial performance

OpenAIRE

Maiga, Adam S; Nilsson, Anders; Jacobs, Fred

2014-01-01

The interface between management control and information technology is an under-developed research area with a knowledge gap concerning its implications for financial performance. This study contributes to bridging this gap by investigates the interaction effect of cost control systems and information technology integration on manufacturing plant financial performance. We surveyed a sample of 518 managers of U.S. manufacturing plants, approximately evenly distributed between those using activ...

Methods and Technologies of XML Data Modeling for IP Mode Intelligent Measuring and Controlling System

International Nuclear Information System (INIS)

Liu, G X; Hong, X B; Liu, J G

2006-01-01

This paper presents the IP mode intelligent measuring and controlling system (IMIMCS). Based on object-oriented modeling technology of UML and XML Schema, the innovative methods and technologies of some key problems for XML data modeling in the IMIMCS were especially discussed, including refinement for systemic business by means of use-case diagram of UML, the confirmation of the content of XML data model and logic relationship of the objects of XML Schema with the aid of class diagram of UML, the mapping rules from the UML object model to XML Schema. Finally, the application of the IMIMCS based on XML for a modern greenhouse was presented. The results show that the modeling methods of the measuring and controlling data in the IMIMCS involving the multi-layer structure and many operating systems process strong reliability and flexibility, guarantee uniformity of complex XML documents and meet the requirement of data communication across platform

From control switches to integrated process control systems. 60 years of power plant control technology; Vom Steuerquittierschalter zum integrierten Prozessleitsystem. 60 Jahre Kraftwerksleittechnik

Energy Technology Data Exchange (ETDEWEB)

Pagel, Peter [ABB AG, Mannheim (Germany). Marketing

2009-07-01

Power plant control has always been based on the process requirements and on the need to reduce the process cost. Modern power plant control systems also take account of the need for emission reduction. They have developed into integrated navigation platforms with functional confectioning of workstations, focusing on the aspects of functionality, efficiency, ergonomics, plant availability and life cycle cost. The contribution outlines important developments of power plant control technology during the past few decades. (orig.)

Transference of advanced LMFBR control technology to the aerospace power system program

International Nuclear Information System (INIS)

Chisholm, G.H.

1984-01-01

Much recent R and D has been devoted to the safety of liquid metal fast breeder reactors (LMFBR's). Part of the resulting technology, especially advanced control systems, appears to be directly transferable to the space nuclear power program. Some of the ideas described herein have been already culminated in successful products that are available for application, e.g. analytical redundancy and fault-tolerant computers. Others, in various stages of R and D, are being developed as elements to support the design goals outlined in the following section, e.g. automated software verification, automated hardware verification, and system validation

Intelligent control and automation technology for nuclear applications

International Nuclear Information System (INIS)

Kim, Jae Hui; Huh, Young Hwan; Lee, Jang Soo; Kim, Ko Ryeo; Cha, Kyoung Ho; Lee, Jae Cheol; Dong, In Sook

1993-01-01

This project intends to establish the basic technology of intelligent control and automation to be applied to the next generation nuclear plant. For that, the research status of those technologies is surveyed for various application areas at first. The characteristics and availability of those techniques such as neural network, fuzzy rule based control and reasoning, multimedia, real-time software and qualitative modelling are studied through a series of simulations and experiments. By integrating each technologies studied above, we developed a hierarchical, intelligent control system for an autonomous mobile robot as a test bed. The system is composed of several modules of software and hardware subsystems, which are implemented by use of the intelligent techniques. Through the analysis of the results and experiences, we investigated the feasibility of application of the basic technology to the next generation plant. (Author)

New technology for BWR power plant control and instrumentation

International Nuclear Information System (INIS)

Takano, Yoshiyuki; Nakamura, Makoto; Murata, Fumio.

1992-01-01

Nuclear power plants are facing strong demands for higher reliability and cost-performance in their control and instrumentation systems. To meet these needs, Hitachi is developing advanced control and instrumentation technology by rationalizing the conventional technology in that field. The rationalization is done through the utilization of reliable digital technology and optical transmission technology, and others, which are now commonly used in computer applications. The goal of the development work is to ensure safe, stable operation of the plant facilities and to secure harmony between man and machine. To alleviate the burdens of the operators, the latest electronic devices are being employed to create an advanced man-machine interface, and to promote automatic operation of the plant based upon the automatic operation of individual systems. In addition, the control and instrumentation system, including the safety system, incorporates more and more digital components in order to further enhance the reliability and maintainability of the plant. (author)

Control technologies for soil vapor extraction at petroleum hydrocarbon impacted sites -- Regulatory challenges to system operations

International Nuclear Information System (INIS)

Cacossa, K.F.; Campbell, G.E.; Devine, K.

1995-01-01

Soil vapor extraction (SVE) is frequently used to remediate soils impacted by petroleum hydrocarbons. Four technologies have proven to be viable methods to control the off-gas emissions from SVE systems, namely, internal combustion, thermal oxidation, catalytic oxidation, and granular activated carbon adsorption. The optimal range of influent vapor concentrations for system operation differs for each of the technologies. Over the past several years the authors have worked proactively with the state regulatory community to develop general, all inclusive air pollution control permits which allow for the potential use of all four technologies over the life of the permit. Private industry has similarly worked with the state regulators to develop a less labor intensive sampling/monitoring procedure. Actual system performances, which were monitored using summa canisters and field equipment, provided the basis for the new procedure. System performance data indicated that field sampling with portable hydrocarbon analyzers, such as flame ionization detectors (FID), was preferable over the use of summa canister sampling. In addition, to reduce the costs associated with the analysis of samples, the new SVE monitoring protocol also reduced the number of system monitoring visits. These reductions equated into a cost effective, yet environmentally sound SVE system monitoring programs. Finally, the authors have worked with the regulatory community to establish permit limitations which allow operational flexibility

Exploring the Impact of Fuel Data Acquisition Technology on the USMC Expeditionary Energy Command and Control System

Science.gov (United States)

2016-09-01

CA: Sage Publications, Inc. Tulusan, J., Soi, L., Paefgen, J., Brogle, M., & Staake, T. (2011). Eco -efficient feedback technologies : Which eco ...IMPACT OF FUEL DATA ACQUISITION TECHNOLOGY ON THE USMC EXPEDITIONARY ENERGY COMMAND AND CONTROL SYSTEM by Jeremy F. Thomas September 2016...DATE September 2016 3. REPORT TYPE AND DATES COVERED Master’s Thesis 4. TITLE AND SUBTITLE EXPLORING THE IMPACT OF FUEL DATA ACQUISITION TECHNOLOGY

Wisdom Appliance Control System

Science.gov (United States)

Hendrick; Jheng, Jyun-Teng; Tsai, Chen-Chai; Liou, Jia-Wei; Wang, Zhi-Hao; Jong, Gwo-Jia

2017-07-01

Intelligent appliances wisdom involves security, home care, convenient and energy saving, but the home automation system is still one of the core unit, and also using micro-processing electronics technology to centralized and control the home electrical products and systems, such as: lighting, television, fan, air conditioning, stereo, it composed of front-controller systems and back-controller panels, user using front-controller to control command, and then through the back-controller to powered the device.

Inlet Flow Control and Prediction Technologies for Embedded Propulsion Systems

Science.gov (United States)

McMillan, Michelle L.; Mackie, Scott A.; Gissen, Abe; Vukasinovic, Bojan; Lakebrink, Matthew T.; Glezer, Ari; Mani, Mori; Mace, James L.

2011-01-01

Fail-safe, hybrid, flow control (HFC) is a promising technology for meeting high-speed cruise efficiency, low-noise signature, and reduced fuel-burn goals for future, Hybrid-Wing-Body (HWB) aircraft with embedded engines. This report details the development of HFC technology that enables improved inlet performance in HWB vehicles with highly integrated inlets and embedded engines without adversely affecting vehicle performance. In addition, new test techniques for evaluating Boundary-Layer-Ingesting (BLI)-inlet flow-control technologies developed and demonstrated through this program are documented, including the ability to generate a BLI-like inlet-entrance flow in a direct-connect, wind-tunnel facility, as well as, the use of D-optimal, statistically designed experiments to optimize test efficiency and enable interpretation of results. Validated improvements in numerical analysis tools and methods accomplished through this program are also documented, including Reynolds-Averaged Navier-Stokes CFD simulations of steady-state flow physics for baseline, BLI-inlet diffuser flow, as well as, that created by flow-control devices. Finally, numerical methods were employed in a ground-breaking attempt to directly simulate dynamic distortion. The advances in inlet technologies and prediction tools will help to meet and exceed "N+2" project goals for future HWB aircraft.

State-of-the-art report for the instrumentation and control technology based on the nuclear-information technology convergence

International Nuclear Information System (INIS)

Kwon, Kee Choon; Kim, Chang Hwoi; Lee, Dong Young; Lee, Cheol Kwon; Lee, Hyun Chul

2011-12-01

As digitalized the instrumentation and control systems in nuclear power plants, in the past that were implemented in an analog system or circuit for monitoring, control and protection, most of the them is implemented in embedded software based on hardware platform. Digital instrumentation and control system hardware platforms and a digital safety systems have developed in Korea. The fundamental technology of the software part of MMIS (Man-Machine Interface System) has achieved the localization. But in order to secure our global competitiveness, in the -based software, the source of the content areas / It is needed to develop core technologies of the software and contents areas based on the nuclear-IT convergence technology. In this report, the IT technology centered for the characteristics of embedded software applied to nuclear power is described. Also state-of-the-art IT technologies that will converge to nuclear power plants are mentioned

Quality indicators in a computerized technology information system

International Nuclear Information System (INIS)

Mancuso, C.A.; Hyde, R.A.

1992-01-01

An environmental technology information system was developed by EG ampersand G Idaho, Inc. at the Idaho National Engineering Laboratory (INEL) for the Department of Energy (DOE). The purpose of the system is to reduce costs and time associated with evaluating potential remedial alternatives for a waste site. The information system is organized to aid in the CERCLA process by describing the implementability, effectiveness, and cost of many remedial technologies. Technology categories included in the information system include: Institutional Controls, Retrieval, Separation, Characterization, Physical/Chemical Treatment, Biological Treatment, Thermal Treatment, Storage, Transportation, Disposal, Migration Control (containment), Support Systems, Waste Minimization, and Remote Operations. Two hundred and sixty processes are summarized in these technology areas. Information on these processes was collected from EPA publications, books, journal articles, conference proceedings, vendors, DOE publications, and technical experts. The purpose of this paper is to familiarize readers with issues associated with the development of information systems. A major issue is the system and software quality, which can be controlled by configuration management. Another major issue is the documentation of data quality indicators in references used to collect data for the system, which can not be controlled but must be planned for in the review process

Propulsion/flight control integration technology (PROFIT) software system definition

Science.gov (United States)

Carlin, C. M.; Hastings, W. J.

1978-01-01

The Propulsion Flight Control Integration Technology (PROFIT) program is designed to develop a flying testbed dedicated to controls research. The control software for PROFIT is defined. Maximum flexibility, needed for long term use of the flight facility, is achieved through a modular design. The Host program, processes inputs from the telemetry uplink, aircraft central computer, cockpit computer control and plant sensors to form an input data base for use by the control algorithms. The control algorithms, programmed as application modules, process the input data to generate an output data base. The Host program formats the data for output to the telemetry downlink, the cockpit computer control, and the control effectors. Two applications modules are defined - the bill of materials F-100 engine control and the bill of materials F-15 inlet control.

Architecture and technology of 500 Msample/s feedback systems for control of coupled-bunch instabilities

International Nuclear Information System (INIS)

Teytelman, Dmitry

2000-01-01

Feedback control of coupled-bunch instabilities presents many challenges. Control bandwidths up to 250 MHz are required to damp all of the unstable coupled-bunch modes in recent accelerators. A digital parallel-processing array with 80 DSPs has been developed to control longitudinal instabilities in PEP-II/ALS/DA NE machines. Here the authors present a description of the architecture as well as the technologies used to implement 500 Msample/s real-time control system with 2,000 FIR filtering channels. Algorithms for feedback control, data acquisition, and analysis are described and measurements from ALS are presented

How controlled release technology can aid gene delivery.

Science.gov (United States)

Jo, Jun-Ichiro; Tabata, Yasuhiko

2015-01-01

Many types of gene delivery systems have been developed to enhance the level of gene expression. Controlled release technology is a feasible gene delivery system which enables genes to extend the expression duration by maintaining and releasing them at the injection site in a controlled manner. This technology can reduce the adverse effects by the bolus dose administration and avoid the repeated administration. Biodegradable biomaterials are useful as materials for the controlled release-based gene delivery technology and various biodegradable biomaterials have been developed. Controlled release-based gene delivery plays a critical role in a conventional gene therapy and genetic engineering. In the gene therapy, the therapeutic gene is released from biodegradable biomaterial matrices around the tissue to be treated. On the other hand, the intracellular controlled release of gene from the sub-micro-sized matrices is required for genetic engineering. Genetic engineering is feasible for cell transplantation as well as research of stem cells biology and medicine. DNA hydrogel containing a sequence of therapeutic gene and the exosome including the individual specific nucleic acids may become candidates for controlled release carriers. Technologies to deliver genes to cell aggregates will play an important role in the promotion of regenerative research and therapy.

Energy Efficient Engine: Control system preliminary definition report

Science.gov (United States)

Howe, David C.

1986-01-01

The object of the Control Preliminary Definition Program was to define a preliminary control system concept as a part of the Energy Efficient Engine program. The program was limited to a conceptual definition of a full authority digital electronic control system. System requirements were determined and a control system was conceptually defined to these requirements. Areas requiring technological development were identified and a plan was established for implementing the identified technological features, including a control technology demonstration. A significant element of this program was a study of the potential benefits of closed-loop active clearance control, along with laboratory tests of candidate clearance sensor elements for a closed loop system.

Achievement report for fiscal 1998. Development of control system technologies such as combustion with energy consumption rationalized; 1998 nendo seika hokokusho. Energy shiyo gorkika nensho nado seigyo system gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

To improve and optimize fuel control systems, basic technologies were studied for building SiC devices capable of high-temperature operation. The technologies involved the construction of single-crystal SiC substrates, development of element technologies such as conduction control, experimental production of SiC devices, and systems incorporating SiC devices for controlling, for example, combustion. The subjects of research and development for fiscal 1998 included the technologies related to common SiC semiconductor substrates (SiC substrate crystallinity evaluation by X-ray topography, thermal oxidation acceleration by ion irradiation, and annealing of ion-implanted SiC by excimer laser ), technologies of forming an SiC single crystal into a substrate, technologies related to SiC sensors, technologies related to SiC devices capable of operation at high temperature and high speed, technologies related to SiC devices for controlling, and technologies for controlling, for example, combustion. The subjects of basic researches at universities and research institutes included new crystal growing methods, ion beam-aided SiC synthesis, effect of irradiation of SiC with neutrons, and nuclear conversion implantation. (NEDO)

The development of advanced instrumentation and control technology -The development of basic technology for instrumentation and control-

Energy Technology Data Exchange (ETDEWEB)

Ham, Chang Sik; Kwon, Kee Choon; Park, Jae Chang; Kim, Jung Taek; Jung, Chul Hwan; Lee, Dong Yung; Kim, Chang Hoi; Hwang, In Koo; Kim, Jung Soo; Nah, Nan Joo [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1995-07-01

In this report automatic startup technology and dynamic alarm processing technology are developed. We designed an automatic control system had four modes and six break points. The four modes are heating mode I, heating mode II, heating mode III and critical mode. The six break points are RHR isolation and pressurizer bubble generation, P-6, critical conformation and another three break points for the start point of each mode from heating mode II to critical mode. We defined control variables and components at each mode and developed control algorithms. The conceptual design for automatic startup system configuration and interface with test facility was developed. These results will be used for detail design and software implementation in the project of next year. For development of dynamic alarm processing technology, necessary techniques were selected according to the survey on current development activities and the analysis on design documents. Alarm operating procedures were studied for obtaining casual relationships among alarms and part of a preliminary prototype was implemented in this first year using the results of the analysis including various techniques studied during the survey and analysis stage. 70 figs, 7 tabs, 77 refs. (Author).

Propulsion Control Technology Development in the United States A Historical Perspective

Science.gov (United States)

Jaw, Link C.a; Garg, Sanjay

2005-01-01

This paper presents a historical perspective of the advancement of control technologies for aircraft gas turbine engines. The paper primarily covers technology advances in the United States in the last 60 years (1940 to approximately 2002). The paper emphasizes the pioneering technologies that have been tested or implemented during this period, assimilating knowledge and experience from industry experts, including personal interviews with both current and retired experts. Since the first United States-built aircraft gas turbine engine was flown in 1942, engine control technology has evolved from a simple hydro-mechanical fuel metering valve to a full-authority digital electronic control system (FADEC) that is common to all modern aircraft propulsion systems. At the same time, control systems have provided engine diagnostic functions. Engine diagnostic capabilities have also evolved from pilot observation of engine gauges to the automated on-board diagnostic system that uses mathematical models to assess engine health and assist in post-flight troubleshooting and maintenance. Using system complexity and capability as a measure, we can break the historical development of control systems down to four phases: (1) the start-up phase (1942 to 1949), (2) the growth phase (1950 to 1969), (3) the electronic phase (1970 to 1989), and (4) the integration phase (1990 to 2002). In each phase, the state-of-the-art control technology is described and the engines that have become historical landmarks, from the control and diagnostic standpoint, are identified. Finally, a historical perspective of engine controls in the last 60 years is presented in terms of control system complexity, number of sensors, number of lines of software (or embedded code), and other factors.

Development of Plant Control Diagnosis Technology and Increasing Its Applications

Science.gov (United States)

Kugemoto, Hidekazu; Yoshimura, Satoshi; Hashizume, Satoru; Kageyama, Takashi; Yamamoto, Toru

A plant control diagnosis technology was developed to improve the performance of plant-wide control and maintain high productivity of plants. The control performance diagnosis system containing this technology picks out the poor performance loop, analyzes the cause, and outputs the result on the Web page. Meanwhile, the PID tuning tool is used to tune extracted loops from the control performance diagnosis system. It has an advantage of tuning safely without process changes. These systems are powerful tools to do Kaizen (continuous improvement efforts) step by step, coordinating with the operator. This paper describes a practical technique regarding the diagnosis system and its industrial applications.

Siemens: Smart Technologies for Large Control Systems

CERN Multimedia

CERN. Geneva; BAKANY, Elisabeth

2015-01-01

The CERN Large Hadron Collider (LHC) is known to be one of the most complex scientific machines ever built by mankind. Its correct functioning relies on the integration of a multitude of interdependent industrial control systems, which provide different and essential services to run and protect the accelerators and experiments. These systems have to deal with several millions of data points (e.g. sensors, actuators, configuration parameters, etc…) which need to be acquired, processed, archived and analysed. Since more than 20 years, CERN and Siemens have developed a strong collaboration to deal with the challenges for these large systems. The presentation will cover the current work on the SCADA (Supervisory Control and Data Acquisition) systems and Data Analytics Frameworks.

Noise-control needs in the developing energy technologies

Energy Technology Data Exchange (ETDEWEB)

Keast, D.N.

1978-03-01

The noise characteristics of existing energy conversion technologies, e.g., from obtaining and processing fossil fuels to power plants operations, and of developing energy technologies (wind, geothermal sources, solar energy or fusion systems) are discussed in terms of the effects of noise on humans, animals, structures, and equipment and methods for noise control. Regulations for noise control are described. Recommendations are made for further research on noise control and noise effects. (LCL)

Research, development and technological innovation of wind turbine control systems; Investigacion, desarrollo e innovacion tecnologica de sistemas de control de aerogeneradores

Energy Technology Data Exchange (ETDEWEB)

Garduno Ramirez, Raul; Rodriguez Martinez, Arnulfo Antelmo; Sanchez Parra, Marino; Martinez Morales, Miguel Angel; Hernandez Cuellar, Maria Aurora; Alcaide Godinez, Indira Xochiquetzal; Re Lopez, Victor Genaro; Hernandez Gonzalez, Roberto [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2012-07-01

Control systems constitute the brain and the nervous system of modern machines, such as wind turbine generators (TGE by its acronym in Spanish). TGEs can work efficiently, safely and almost autonomously, thanks to the control systems with which they are equipped. Conversely, any malfunctioning of the control system may cause failure or damage of a component, a subsystem or even destruction of the TGE itself. This paper introduces some basic facts about generation of electric power from wind energy in the world and Mexico, wind turbogenerators and their most relevant technologies, TGE control systems, and R and TD+I about TGE control systems performed at the Instituto de Investigaciones Electricas. [Spanish] Los sistemas de control constituyen el cerebro y el sistema nervioso de las maquinas modernas, como aerogeneradores (AG). Los AG pueden trabajar eficiente, segura y casi autonomamente, gracias a los sistemas de control con los que estan equipados. De manera inversa, cualquier mal funcionamiento del sistema de control puede provocar falla o dano de un componente, subsistema o incluso la destruccion del propio AG. Este documento introduce algunos hechos basicos en torno a la generacion de energia electrica a partir de energia eolica en el mundo y Mexico, los aerogeneradores y sus tecnologias mas importantes, sistemas de control de AG e I+DT alrededor de los sistemas de control de AG realizados en el Instituto de Investigaciones Electricas.

Study on collaborative optimization control of ventilation and radon reduction system based on multi-agent technology

International Nuclear Information System (INIS)

Dai Jianyong; Meng Lingcong; Zou Shuliang

2015-01-01

According to the radioactive safety features such as radon and its progeny, combined with the theory of ventilation system, structure of multi-agent system for ventilation and radon reduction system is constructed with the application of multi agent technology. The function attribute of the key agent and the connection between the nodes in the multi-agent system are analyzed to establish the distributed autonomous logic structure and negotiation mechanism of multi agent system of ventilation and radon reduction system, and thus to implement the coordination optimization control of the multi-agent system. The example analysis shows that the system structure of the multi-agent system of ventilation and reducing radon system and its collaborative mechanism can improve and optimize the radioactive pollutants control, which provides a theoretical basis and important application prospect. (authors)

En-Tegrity - Advanced subsea well control technology

Energy Technology Data Exchange (ETDEWEB)

Edwards, Jeff

2010-07-01

Shear Seal Valve: En-Tegrity - Advanced subsea well control technology. With the growing complexity of well interventions operations such as zone isolations, chemical treatment, sand removal and side track re-completion drilling, there is an increasing demand for an efficient light well intervention service equipment. This paper details the design, development and qualification program undertaken to introduce a new technology for well interventions operations. The Shear Seal Valve provides dual barrier sealing integrity that is capable of cutting large diameter coiled tubing, drill pipe and intervention tooling within a single compact housing. The hydraulic design of the valve minimizes operating volumes and negates the requirement for mechanical ram locks therefore greatly simplifying control system complexity. Utilizing dual metal to metal sealing technology and a fail safe close rational the system is ideally suited to HPHT applications providing optimum operational integrity. (Author)

The Advanced Technology Operations System: ATOS

Science.gov (United States)

Kaufeler, J.-F.; Laue, H. A.; Poulter, K.; Smith, H.

1993-01-01

Mission control systems supporting new space missions face ever-increasing requirements in terms of functionality, performance, reliability and efficiency. Modern data processing technology is providing the means to meet these requirements in new systems under development. During the past few years the European Space Operations Centre (ESOC) of the European Space Agency (ESA) has carried out a number of projects to demonstrate the feasibility of using advanced software technology, in particular, knowledge based systems, to support mission operations. A number of advances must be achieved before these techniques can be moved towards operational use in future missions, namely, integration of the applications into a single system framework and generalization of the applications so that they are mission independent. In order to achieve this goal, ESA initiated the Advanced Technology Operations System (ATOS) program, which will develop the infrastructure to support advanced software technology in mission operations, and provide applications modules to initially support: Mission Preparation, Mission Planning, Computer Assisted Operations, and Advanced Training. The first phase of the ATOS program is tasked with the goal of designing and prototyping the necessary system infrastructure to support the rest of the program. The major components of the ATOS architecture is presented. This architecture relies on the concept of a Mission Information Base (MIB) as the repository for all information and knowledge which will be used by the advanced application modules in future mission control systems. The MIB is being designed to exploit the latest in database and knowledge representation technology in an open and distributed system. In conclusion the technological and implementation challenges expected to be encountered, as well as the future plans and time scale of the project, are presented.

Multirate flutter suppression system design for the Benchmark Active Controls Technology Wing

Science.gov (United States)

Berg, Martin C.; Mason, Gregory S.

1994-01-01

To study the effectiveness of various control system design methodologies, the NASA Langley Research Center initiated the Benchmark Active Controls Project. In this project, the various methodologies will be applied to design a flutter suppression system for the Benchmark Active Controls Technology (BACT) Wing (also called the PAPA wing). Eventually, the designs will be implemented in hardware and tested on the BACT wing in a wind tunnel. This report describes a project at the University of Washington to design a multirate flutter suppression system for the BACT wing. The objective of the project was two fold. First, to develop a methodology for designing robust multirate compensators, and second, to demonstrate the methodology by applying it to the design of a multirate flutter suppression system for the BACT wing. The contributions of this project are (1) development of an algorithm for synthesizing robust low order multirate control laws (the algorithm is capable of synthesizing a single compensator which stabilizes both the nominal plant and multiple plant perturbations; (2) development of a multirate design methodology, and supporting software, for modeling, analyzing and synthesizing multirate compensators; and (3) design of a multirate flutter suppression system for NASA's BACT wing which satisfies the specified design criteria. This report describes each of these contributions in detail. Section 2.0 discusses our design methodology. Section 3.0 details the results of our multirate flutter suppression system design for the BACT wing. Finally, Section 4.0 presents our conclusions and suggestions for future research. The body of the report focuses primarily on the results. The associated theoretical background appears in the three technical papers that are included as Attachments 1-3. Attachment 4 is a user's manual for the software that is key to our design methodology.

Suitability of Agent Technology for Military Command and Control in the Future Combat System Environment

Energy Technology Data Exchange (ETDEWEB)

Potok, TE

2003-02-13

The U.S. Army is faced with the challenge of dramatically improving its war fighting capability through advanced technologies. Any new technology must provide significant improvement over existing technologies, yet be reliable enough to provide a fielded system. The focus of this paper is to assess the novelty and maturity of agent technology for use in the Future Combat System (FCS). The FCS concept represents the U.S. Army's ''mounted'' form of the Objective Force. This concept of vehicles, communications, and weaponry is viewed as a ''system of systems'' which includes net-centric command and control (C{sup 2}) capabilities. This networked C{sup 2} is an important transformation from the historically centralized, or platform-based, C{sup 2} function since a centralized command architecture may become a decision-making and execution bottleneck, particularly as the pace of war accelerates. A mechanism to ensure an effective network-centric C{sup 2} capacity (combining intelligence gathering and analysis available at lower levels in the military hierarchy) is needed. Achieving a networked C{sup 2} capability will require breakthroughs in current software technology. Many have proposed the use of agent technology as a potential solution. Agents are an emerging technology, and it is not yet clear whether it is suitable for addressing the networked C{sup 2} challenge, particularly in satisfying battlespace scalability, mobility, and security expectations. We have developed a set of software requirements for FCS based on military requirements for this system. We have then evaluated these software requirements against current computer science technology. This analysis provides a set of limitations in the current technology when applied to the FCS challenge. Agent technology is compared against this set of limitations to provide a means of assessing the novelty of agent technology in an FCS environment. From this analysis we

Management of Control System Information SecurityI: Control System Patch Management

Energy Technology Data Exchange (ETDEWEB)

Quanyan Zhu; Miles McQueen; Craig Rieger; Tamer Basar

2011-09-01

The use of information technologies in control systems poses additional potential threats due to the frequent disclosure of software vulnerabilities. The management of information security involves a series of policy-making on the vulnerability discovery, disclosure, patch development and patching. In this paper, we use a system approach to devise a model to understand the interdependencies of these decision processes. In more details, we establish a theoretical framework for making patching decision for control systems, taking into account the requirement of functionability of control systems. We illustrate our results with numerical simulations and show that the optimal operation period of control systems given the currently estimated attack rate is roughly around a half a month.

ACTS TDMA network control. [Advanced Communication Technology Satellite

Science.gov (United States)

Inukai, T.; Campanella, S. J.

1984-01-01

This paper presents basic network control concepts for the Advanced Communications Technology Satellite (ACTS) System. Two experimental systems, called the low-burst-rate and high-burst-rate systems, along with ACTS ground system features, are described. The network control issues addressed include frame structures, acquisition and synchronization procedures, coordinated station burst-time plan and satellite-time plan changes, on-board clock control based on ground drift measurements, rain fade control by means of adaptive forward-error-correction (FEC) coding and transmit power augmentation, and reassignment of channel capacities on demand. The NASA ground system, which includes a primary station, diversity station, and master control station, is also described.

Practical Packaging Technology for Microfluidic Systems

International Nuclear Information System (INIS)

Lee, Hwan Yong; Han, Song I; Han, Ki Ho

2010-01-01

This paper presents the technology for the design, fabrication, and characterization of a microfluidic system interface (MSI): the purpose of this technology is to enable the integration of complex microfluidic systems. The MSI technology can be applied in a simple manner for realizing complex arrangements of microfluidic interconnects, integrated microvalves for fluid control, and optical windows for on-chip optical processes. A microfluidic system for the preparation of genetic samples was used as the test vehicle to prove the effectiveness of the MSI technology for packaging complex microfluidic systems with multiple functionalities. The miniaturized genetic sample preparation system comprised several functional compartments, including compartments for cell purification, cell separation, cell lysis, solid-phase DNA extraction, polymerase chain reaction, and capillary electrophoresis. Additionally, the functional operation of the solid-phase extraction and PCR thermocycling compartments was demonstrated by using the MSI

Generic device controller for accelerator control systems

International Nuclear Information System (INIS)

Mariotti, R.; Buxton, W.; Frankel, R.; Hoff, L.

1987-01-01

Distributed intelligence for accelerator control systems has become possible as a result of advances in microprocessor technology. A system based on distributed intelligence is inherently versatile, readily expandable, and reduces both information flow across the system and software complexity in each unit

Development and Application of Coating Weight Control Technology

Energy Technology Data Exchange (ETDEWEB)

Park, Jin Hyoung [Dongbu Steel, Incheon (Korea, Republic of)

2010-08-15

Precise coating weight control is very important issue on quality and minimizing operating costs on continuous galvanizing line. These days, many steel making companies are having a new understanding of cost importance by rise raw material prices and customers requirement for cost reduction. Dongbu steel also meets these situations and decided to develop the technologies. Dongbu Steel developed Integrated coating weight control system jointly with Objective Control Ltd. and installed 2CGL and 4CGL. Several technological functions were developed and realized to achieve true hands-off operation and maximum cost benefit by combining model-based preset and dynamic prediction models. We also installed it on 1 CGL on April, 2008. This paper will present the interface, functions and application result of the integrated coating weight control system including Zn saving and coating weight uniformity.

Control system integration

CERN Document Server

Shea, T J

2008-01-01

This lecture begins with a definition of an accelerator control system, and then reviews the control system architectures that have been deployed at the larger accelerator facilities. This discussion naturally leads to identification of the major subsystems and their interfaces. We shall explore general strategies for integrating intelligent devices and signal processing subsystems based on gate arrays and programmable DSPs. The following topics will also be covered: physical packaging; timing and synchronization; local and global communication technologies; interfacing to machine protection systems; remote debugging; configuration management and source code control; and integration of commercial software tools. Several practical realizations will be presented.

Technology transfer of nuclear techniques and nucleonic control systems in the mineral industry

International Nuclear Information System (INIS)

1990-11-01

Among the many beneficial applications of radiation and radioisotopes in industry which are now well established in advanced countries, the applications of nuclear techniques and nucleonic control systems in the mineral industry have great potential for developing Member States. The use of nucleonic on-stream analyzers in the coal industry has resulted in enormous technical and economic benefits in addition to minimization of environmental pollution. Large savings have also resulted from the use of such analyzers in the processing of other minerals. Nuclear borehole logging techniques have demonstrated great potential in oil and gas evaluation. Radiotracer investigations have led to process optimisation and trouble shooting in various stages in ore processing and metallurgy. Though the technical and economic benefits of applications of nuclear techniques in the mineral industry are well recognised, technology transfer in these areas has been hampered by a variety of factors. In order to review the status and trends in nuclear techniques and nucleonic control systems in the mineral industry and the problems and considerations in their technology transfer to developing Member States, the IAEA convened an Advisory Group Meeting in Bombay, India, 15-19 January 1990. The present publication is based on the 7 contributions presented at this meeting. A separate abstract was prepared for each of these papers. Refs, figs and tabs

Expert system technology for control integration in nuclear reactors

International Nuclear Information System (INIS)

Stabler, E.P. Jr.; Zimmerman, J.J.; Stratton, R.C.

1986-03-01

This report describes the role of expert system technology in nuclear power plant operation. The use of computers to assist operator decisions would greatly enhance the safety and efficiency of operation. A description of the necessary operator interfaces, data acquisition and validation, plant status and parameter diagnosis, and system reliability is presented. (FL)

USE OF UBIQUITOUS TECHNOLOGIES IN MILITARY LOGISTIC SYSTEM IN IRAN

Directory of Open Access Journals (Sweden)

P. Jafari

2013-09-01

Full Text Available This study is about integration and evaluation of RFID and ubiquitous technologies in military logistic system management. Firstly, supply chain management and the necessity of a revolution in logistic systems especially in military area, are explained. Secondly RFID and ubiquitous technologies and the advantages of their use in supply chain management are introduced. Lastly a system based on these technologies for controlling and increasing the speed and accuracy in military logistic system in Iran with its unique properties, is presented. The system is based on full control of military logistics (supplies from the time of deployment to replenishment using sensor network, ubiquitous and RFID technologies.

Use of Ubiquitous Technologies in Military Logistic System in Iran

Science.gov (United States)

Jafari, P.; Sadeghi-Niaraki, A.

2013-09-01

This study is about integration and evaluation of RFID and ubiquitous technologies in military logistic system management. Firstly, supply chain management and the necessity of a revolution in logistic systems especially in military area, are explained. Secondly RFID and ubiquitous technologies and the advantages of their use in supply chain management are introduced. Lastly a system based on these technologies for controlling and increasing the speed and accuracy in military logistic system in Iran with its unique properties, is presented. The system is based on full control of military logistics (supplies) from the time of deployment to replenishment using sensor network, ubiquitous and RFID technologies.

Experience of digital control systems in Scandinavian BWRs

International Nuclear Information System (INIS)

Rydahl, I.

1989-01-01

Since 1984 digital control systems have been in operation in various Scandinavian BWRs. Examples of such digital control systems are: dual microprocessor based system for complete control of radwaste plant, three channel recirculation control system, and three channel feedwater control system. This paper describes Swedish development from one channel through three channel analog control systems to digital systems. The author describes experience of digital control systems during design, testing, commissioning and operation. The main benefits of digital compared with analog technology are discussed. Especially the outstanding facility of using a built-in process simulator for commissioning and tuning. The use of digital technology in nuclear safety system and future plans are dealt with

Emulating Industrial Control System Field Devices Using Gumstix Technology

Science.gov (United States)

2012-06-01

Security mechanisms (e.g., intrusion detection systems, antivirus and honeypots) are employed in traditional Information Technology (IT) systems to detect...can be used to determine the vendor of the device if the fingerprinting is done on a local segment. 2.8 Emulation Emulation is software or...Each of the honeypots in the network can be different systems ranging from Windows workstations to IIS web servers to Cisco routers. Honeynets rely

The establishment of master plan for developing advanced I and C technology -The development of advanced instrumentation and control technology-

International Nuclear Information System (INIS)

Ham, Chang Shik; Lee, Byung Sun; Kwon, Kee Choon; Lee, Dong Young; Hwang, In Koo; Lee, Jang Soo; Kim, Jung Soo; Kim, Chang Hwoi; Jung, Chul Hwan; Na, Nan Ju; Dong, In Sook; Kang, Soon Gu; Lyu, Chan Ho; Song, Soon Ja

1994-07-01

Although several organizations are performing their tasks making efforts to develop new digital technology for application to existing nuclear power plants as well as new plants of the future, their projects are similar to each other and have possibilities of redundant investment. Therefore, KAERI have established a Master Plan to define the suitable work-scope of each Instrumentation and Control (I and C) development project and proceed its development items continuously. Furthermore, in the project, several kinds of advanced technology for application of computer science and digital electronics were studied to obtain better reliability of the I and C systems and reduce opertor's burden. For establishing the Master Plan, functions of I and C system of NPPs were surveyed. Especially EPRI URD was deeply analyzed for setting up a basis of the foreign countries were referred for the Master Plan. For the new technology survey, fault-tolerant control technology and control system performance analysis methods were studied. Requirements of alarm and information system as well as technology of I and C network system of NPPs were also established to introduce the advantages of commercial distributed control system. (Author)

Propellantless Attitude Control of Solar Sail Technology Utilizing Reflective Control Devices

Science.gov (United States)

Munday, Jeremy

2016-01-01

Solar sails offer an opportunity for a CubeSatscale, propellant-free spacecraft technology that enables long-term and long-distance missions not possible with traditional methods. Solar sails operate using the transfer of linear momentum from photons of sunlight reflected from the surface of the sail. To propel the spacecraft, no mechanically moving parts, thrusters, or propellant are needed. However, attitude control, or orientation, is still performed using traditional methods involving reaction wheels and propellant ejection, which severely limit mission lifetime. For example, the current state of the art solutions employed by upcoming missions couple solar sails with a state of the art propellant ejection gas system. Here, the use of the gas thruster has limited the lifetime of the mission. To solve the limited mission lifetime problem, the Propellantless Attitude Control of Solar Sail Technology Utilizing Reflective Control Devices project team is working on propellantless attitude control using thin layers of material, an optical film, electrically switchable from transparent to reflective. The technology is based on a polymer-dispersed liquid crystal (PDLC), which allows this switch upon application of a voltage. This technology removes the need for propellant, which reduces weight and cost while improving performance and lifetime.

Water pollution control technology and strategy for river-lake systems: a case study in Gehu Lake and Taige Canal.

Science.gov (United States)

Zhang, Yimin; Zhang, Yongchun; Gao, Yuexiang; Zhang, Houhu; Cao, Jianying; Cai, Jinbang; Kong, Xiangji

2011-07-01

The Taoge water system is located in the upstream of Taihu Lake basin and is characterized by its multi-connected rivers and lakes. In this paper, current analyses of hydrology, hydrodynamics and water pollution of Gehu Lake and Taige Canal are presented. Several technologies are proposed for pollution prevention and control, and water environmental protection in the Taihu Lake basin. These included water pollution control integration technology for the water systems of Gehu Lake, Taige Canal and Caoqiao River. Additionally, river-lake water quality and quantity regulation technology, ecological restoration technology for polluted and degraded water bodies, and water environmental integration management and optimization strategies were also examined. The main objectives of these strategies are to: (a) improve environmental quality of relative water bodies, prevent pollutants from entering Gehu Lake and Taige Canal, and ensure that the clean water after the pre-treatment through Gehu Lake is not polluted before entering the Taihu Lake through Taige Canal; (b) stably and efficiently intercept and decrease the pollution load entering the lake through enhancing the river outlet ecological system structure function and water self-purifying capacity, and (c) designate Gehu Lake as a regulation system for water quality and water quantity in the Taoge water system and thus guarantee the improvement of the water quality of the inflow into Taihu Lake.

Security of legacy process control systems : Moving towards secure process control systems

NARCIS (Netherlands)

Oosterink, M.

2012-01-01

This white paper describes solutions which organisations may use to improve the security of their legacy process control systems. When we refer to a legacy system, we generally refer to old methodologies, technologies, computer systems or applications which are still in use, despite the fact that

Systems engineering identification and control of mixed waste technology development

International Nuclear Information System (INIS)

Beitel, G.A.

1997-01-01

The Department of Energy (DOE) established the Mixed Waste Characterization, Treatment, and Disposal Focus Area (MWFA) to develop technologies required to meet the Department's commitments for treatment of mixed low-level and transuranic wastes. Waste treatment includes all necessary steps from generation through disposal. Systems engineering was employed to reduce programmatic risk, that is, risk of failure to meet technical commitments within cost and schedule. Customer needs (technology deficiencies) are identified from Site Treatment Plans, Consent Orders, ten year plans, Site Technical Coordinating Groups, Stakeholders, and Site Visits. The Technical Baseline, a prioritized list of technology deficiencies, forms the basis for determining which technology development activities will be supported by the MWFA. Technology Development Requirements Documents are prepared for each technology selected for development. After technologies have been successfully developed and demonstrated, they are documented in a Technology Performance Report. The Technology Performance Reports are available to any of the customers or potential users of the technology, thus closing the loop between problem identification and product development. This systematic approach to technology development and its effectiveness after 3 years is discussed in this paper

Fibradapt trademark: Adaptive Wind Turbine Control System; Fibradapt trademark: Adaptive Wind Turbine Control System

Energy Technology Data Exchange (ETDEWEB)

Wernicke, J.-Th. [Wind Force Engineering and Consulting GmbH, Bremerhaven (Germany)

2004-07-01

The technology of Time Division Multiplexing (TDM) is compared with conventional strain gauge technologies in practical operation in a wind power system. Load cycles in the rotor blade were measured during plant life, and the data were used in plant control. The system is a tool in technical project management and financial management of a wind park. (orig.)

Modelling the impact of technology on anti poaching command and control systems

CSIR Research Space (South Africa)

Oosthuizen, R

2015-06-01

Full Text Available Introducing a new technology into a complex sociotechnical system will have planned as well as unplanned impact. The need for a new technology may arise from new technology available for improved performance (technology push) or changes...

The implementation of virtualization technology in EAST data system

International Nuclear Information System (INIS)

Wang, Feng; Sun, Xiaoyang; Li, Shi; Wang, Yong; Xiao, Bingjia; Chang, Sidi

2014-01-01

Highlights: • The server virtualization based on XenServer has been used in EAST data center for common servers and software development platform. • The application virtualization based on XenApp has been demonstrated in EAST to provide an easy and unified data browser method. • The desktop virtualization based on XenDesktop has been adopted for desktop virtualization in the new EAST central control room. - Abstract: The virtualization technology is very popular in many fields at present which has many advantages such as reducing costs, unified management, mobile applications, cross platform, etc. We have also implemented the virtualization technology in EAST control and data system. There are primarily four kinds of technology providers in virtualization technology including VMware, Citrix, Microsoft Hyper-V as well as open source solutions. We have chosen the Citrix solution to implement our virtualization system which mainly includes three aspects. Firstly, we adopt the XenServer technology to realize virtual server for EAST data management and service system. Secondly, we use XenApp technology to realize cross platform system for unify data access. Thirdly, in order to simplify the management of the client computers, we adopt the XenDesktop technology to realize virtual desktops for new central control room. The details of the implementation are described in this paper

Disruptive technology for vector control: the Innovative Vector Control Consortium and the US Military join forces to explore transformative insecticide application technology for mosquito control programmes.

Science.gov (United States)

Knapp, Jennifer; Macdonald, Michael; Malone, David; Hamon, Nicholas; Richardson, Jason H

2015-09-26

Malaria vector control technology has remained largely static for decades and there is a pressing need for innovative control tools and methodology to radically improve the quality and efficiency of current vector control practices. This report summarizes a workshop jointly organized by the Innovative Vector Control Consortium (IVCC) and the Armed Forces Pest Management Board (AFPMB) focused on public health pesticide application technology. Three main topics were discussed: the limitations with current tools and techniques used for indoor residual spraying (IRS), technology innovation to improve efficacy of IRS programmes, and truly disruptive application technology beyond IRS. The group identified several opportunities to improve application technology to include: insuring all IRS programmes are using constant flow valves and erosion resistant tips; introducing compression sprayer improvements that help minimize pesticide waste and human error; and moving beyond IRS by embracing the potential for new larval source management techniques and next generation technology such as unmanned "smart" spray systems. The meeting served to lay the foundation for broader collaboration between the IVCC and AFPMB and partners in industry, the World Health Organization, the Bill and Melinda Gates Foundation and others.

Automated systems for control of technological processes at nuclear power plants and their use in putting the plant into operation

International Nuclear Information System (INIS)

Majtan, L.

1987-01-01

The systems of testing and control of technological processes in WWER-440 units in nuclear power plants which have so far been constructed in Czechoslovakia have been based on the conceptual principles and hardware used in the USSR. For the Mochovce nuclear power plant an automated process control system is to be introduced which proceeds from experiences gained with new Czechoslovak conventional power plants with 200 MW units. The control system consists of two levels: unit control and the control of the whole power plant the unit control consists of the DERIS-900 decentralized control system and the SM 1804 microcomputer and SM 1420 minicomputer based information and control system. A data processing system based on the SM 52/11.M1 minicomputer system will be used for power plant start-up and commissioning. (Z.M.). 2 figs., 4 refs

Self Assistive Technology for Disabled People – Voice Controlled Wheel Chair and Home Automation System

Directory of Open Access Journals (Sweden)

R. Puviarasi

2014-07-01

Full Text Available This paper describes the design of an innovative and low cost self-assistive technology that is used to facilitate the control of a wheelchair and home appliances by using advanced voice commands of the disabled people. This proposed system will provide an alternative to the physically challenged people with quadriplegics who is permanently unable to move their limbs (but who is able to speak and hear and elderly people in controlling the motion of the wheelchair and home appliances using their voices to lead an independent, confident and enjoyable life. The performance of this microcontroller based and voice integrated design is evaluated in terms of accuracy and velocity in various environments. The results show that it could be part of an assistive technology for the disabled persons without any third person’s assistance.

Status of the ATLAS control system upgrade

International Nuclear Information System (INIS)

Munson, F.H.; Ferraretto, M.; Rutherford, B.

1992-01-01

Certain components of the ATLAS control system are two generations behind today's technology. It has been decided to upgrade the control system. in part, by replacing Digital Equipment Corporation (DEC) PDP-11 computers with present-day VAX technology. Two primary goals have been defined for the upgraded control system. The first of these goals is to keep additional ''in-house'' written software to a minimum, while providing the portability necessary to ensure the continued use of existing software. In an attempt to achieve this goal, commercially-available software has been utilized to provide a foundation for the final control-system configuration. The second goal is to develop the new control system, while not interfering with accelerator operations. This paper describes some of the motivation for upgrading the ATLAS control system, the basic features of the new control system, and the present status of the system's development

Report on achievements of research and development of an automatic sewing system in fiscal 1985. System management and control technology; 1985 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. System kanri seigyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-01

This paper describes the system management and control technology, extracted from the achievement report for fiscal 1985 on developing an automatic sewing system. The comprehensive system management has verified algorithms for the optimal process formation and load balancing based on the industry's latest market and production plan trends, and obtained good results. Furthermore, structuring, discussions and proposals were made on an interface system of an optimal process controlling computer with an automatic device controlling micro computer. The inspection and failure diagnosis have set a quality standard for intermediate products in the sewing lines, and verified that its automation is possible by using an image processing technology that identifies dimensional inspection and colors. In the research of printing control information, calculations were performed on the information amount, printing locations, expression method and printing speed, narrowing down to parts ID and location information as the required printing information. Thus,items of basic information for media, media printing and printing device design were put into order. The information recognizing technology has picked up image recognition applying locations in a sewing factory and problems therein, and performed evaluation experiments on specific pattern matching and processing position recognition to have obtained the prospect of application of the automation. (NEDO)

Report on achievements of research and development of an automatic sewing system in fiscal 1985. System management and control technology; 1985 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. System kanri seigyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-01

This paper describes the system management and control technology, extracted from the achievement report for fiscal 1985 on developing an automatic sewing system. The comprehensive system management has verified algorithms for the optimal process formation and load balancing based on the industry's latest market and production plan trends, and obtained good results. Furthermore, structuring, discussions and proposals were made on an interface system of an optimal process controlling computer with an automatic device controlling micro computer. The inspection and failure diagnosis have set a quality standard for intermediate products in the sewing lines, and verified that its automation is possible by using an image processing technology that identifies dimensional inspection and colors. In the research of printing control information, calculations were performed on the information amount, printing locations, expression method and printing speed, narrowing down to parts ID and location information as the required printing information. Thus,items of basic information for media, media printing and printing device design were put into order. The information recognizing technology has picked up image recognition applying locations in a sewing factory and problems therein, and performed evaluation experiments on specific pattern matching and processing position recognition to have obtained the prospect of application of the automation. (NEDO)

Developing an Integration Infrastructure for Distributed Engine Control Technologies

Science.gov (United States)

Culley, Dennis; Zinnecker, Alicia; Aretskin-Hariton, Eliot; Kratz, Jonathan

2014-01-01

Turbine engine control technology is poised to make the first revolutionary leap forward since the advent of full authority digital engine control in the mid-1980s. This change aims squarely at overcoming the physical constraints that have historically limited control system hardware on aero-engines to a federated architecture. Distributed control architecture allows complex analog interfaces existing between system elements and the control unit to be replaced by standardized digital interfaces. Embedded processing, enabled by high temperature electronics, provides for digitization of signals at the source and network communications resulting in a modular system at the hardware level. While this scheme simplifies the physical integration of the system, its complexity appears in other ways. In fact, integration now becomes a shared responsibility among suppliers and system integrators. While these are the most obvious changes, there are additional concerns about performance, reliability, and failure modes due to distributed architecture that warrant detailed study. This paper describes the development of a new facility intended to address the many challenges of the underlying technologies of distributed control. The facility is capable of performing both simulation and hardware studies ranging from component to system level complexity. Its modular and hierarchical structure allows the user to focus their interaction on specific areas of interest.

Advanced liquid metal reactor plant control system

International Nuclear Information System (INIS)

Dayal, Y.; Wagner, W.; Zizzo, D.; Carroll, D.

1993-01-01

The modular Advanced Liquid Metal Reactor (ALMR) power plant is controlled by an advanced state-of-the-art control system designed to facilitate plant operation, optimize availability, and protect plant investment. The control system features a high degree of automatic control and extensive amount of on-line diagnostics and operator aids. It can be built with today's control technology, and has the flexibility of adding new features that benefit plant operation and reduce O ampersand M costs as the technology matures

An Auto-Tuning PI Control System for an Open-Circuit Low-Speed Wind Tunnel Designed for Greenhouse Technology.

Science.gov (United States)

Espinoza, Karlos; Valera, Diego L; Torres, José A; López, Alejandro; Molina-Aiz, Francisco D

2015-08-12

Wind tunnels are a key experimental tool for the analysis of airflow parameters in many fields of application. Despite their great potential impact on agricultural research, few contributions have dealt with the development of automatic control systems for wind tunnels in the field of greenhouse technology. The objective of this paper is to present an automatic control system that provides precision and speed of measurement, as well as efficient data processing in low-speed wind tunnel experiments for greenhouse engineering applications. The system is based on an algorithm that identifies the system model and calculates the optimum PI controller. The validation of the system was performed on a cellulose evaporative cooling pad and on insect-proof screens to assess its response to perturbations. The control system provided an accuracy of integrated software unit that manages the tests in terms of airflow speed and pressure drop set points.

FY1987 report on the result of the R and D of an automatic sewing system. System management/control technology; 1987 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. System kanri seigyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

The paper summarized the R and D of system management/control technology which is an element technology of an automatic sewing system by the Automatic Sewing System Technology Research Association. The effects were confirmed by experiments such as the inspection of dimensions of sewing parts using image processing technology, inspection of the surface state to examine if or not there are darts and pintucks, making and demonstration of the recognition treatment software for fitting patterns on the pocket with big cross stripes, strengthening of the function to determine processing position, etc. Improvement was added to 7 segment letters which becomes ID information so that 8mm letters could be read at a recognition rate of more than 95%. The information required for production plan was summarized after making it mutually connected. Further, a method was worked out for estimation of the standard time required for making the day schedule. Files for drawing-up the optimum process and for process control simulator were made by the expression peculiar to apparel. The framework of the interface was prepared to make the following clear: the integration of the process control use computer into the microcomputer for control of automatic machines such as devices and presses for sewing preparation, multi-functional sewing, assembly sewing, cloth handling/positioning, and the sharing of functions. (NEDO)

Intelligent control and automation technology for nuclear applications

International Nuclear Information System (INIS)

Kim, Jae Hee; Kim, Ko Ryeo; Lee, Jae Cheol; Eom, Heung Seop; Lee, Jang Soo

1994-01-01

Using recently established intelligent mobile robot theory and high technologies in computer science, we have designed an inspection automation system for welded parts of the reactor vessel, and we intend to establish basic technologies. The recent status of those technologies is surveyed for various application areas, and the characteristics and availability of those techniques such as intelligent mobile robot, digital computer control, intelligent user interface, realtime data processing, ultrasonic signal processing, intelligent user interface, intelligent defect recognition, are studied and examined at first. The high performance and compact size inspection system is designed, and if implemented, it is expected to be very efficient in economic point of view. In addition, the use of integrated SW system leads to the reduction of human errors. Through the analysis results and experiences, we investigated the further feasibility of basic technology applications to the various similar operation systems in NPP. (Author)

Applicability of Agent-Based Technology for Acquisition, Monitoring and Process Control Systems at Real Time for Distributed Architectures

International Nuclear Information System (INIS)

Dorao, Carlos; Fontanini, H; Fernandez, R

2000-01-01

Modern industrial plants are characterized by their large size and higher complexity of the processes involved in their operations.The real time monitoring systems of theses plants must be used a distributed architecture.Due to the pressure of competitive markets, an efficient adaptability to changes must be present in the plants.Modifications in the plants due to changes in the lay-out, the introduction of newer supervision, control and monitoring technologies must not affect the integrity of the systems.The aim of this work is give an introduction to the agent-based technology and analyze it advantage for the development of a modern monitoring system

Specialists meeting on design and assessment of instrumentation and control systems in NPP coping with rapid technological change

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-10-01

A transition from analogue to computer based I and C (instrumentation and control) systems in nuclear power plants enabled the industry not only to make use of advantages of computers for the control of technological processes, but also transferred the unusual short innovation cycles in computer technology to become a constraint on the process I and C. This situation led the IAEA to provide an international forum for the presentation and discussion of the problems and organize a Specialists` Meeting in the framework of the International Working Group on Nuclear Power Plant Control and Instrumentation. The basic objective was to elaborate the management, engineering and economic problems arising from rapid technological changes, to point out solutions and to discuss the future trends in the field. The Year 2000 Issue was also inside the scope of the Meeting. Typical problems were technology changes provoking major I and C concept changes, spare part availability, compatibility in refurbishment processes. The present document contains the papers presented by national delegates, each with an abstract, and the conclusions drawn from the final discussion Refs, figs, tabs

Specialists meeting on design and assessment of instrumentation and control systems in NPP coping with rapid technological change

International Nuclear Information System (INIS)

1998-10-01

A transition from analogue to computer based I and C (instrumentation and control) systems in nuclear power plants enabled the industry not only to make use of advantages of computers for the control of technological processes, but also transferred the unusual short innovation cycles in computer technology to become a constraint on the process I and C. This situation led the IAEA to provide an international forum for the presentation and discussion of the problems and organize a Specialists' Meeting in the framework of the International Working Group on Nuclear Power Plant Control and Instrumentation. The basic objective was to elaborate the management, engineering and economic problems arising from rapid technological changes, to point out solutions and to discuss the future trends in the field. The Year 2000 Issue was also inside the scope of the Meeting. Typical problems were technology changes provoking major I and C concept changes, spare part availability, compatibility in refurbishment processes. The present document contains the papers presented by national delegates, each with an abstract, and the conclusions drawn from the final discussion

Improving Blood Pressure Control Using Smart Technology.

Science.gov (United States)

Ciemins, Elizabeth L; Arora, Anupama; Coombs, Nicholas C; Holloway, Barbara; Mullette, Elizabeth J; Garland, Robin; Walsh Bishop-Green, Shannon; Penso, Jerry; Coon, Patricia J

2018-03-01

The authors sought to determine if wireless oscillometric home blood pressure monitoring (HBPM) that integrates with smartphone technology improves blood pressure (BP) control among patients with new or existing uncontrolled hypertension (HTN). A prospective observational cohort study monitored BP control before and after an educational intervention and introduction to HBPM. Patients in the intervention group were instructed to track their BP using a smartphone device three to seven times per week. Cases were matched to controls at a 1:3 allocation ratio on several clinical characteristics over the same period and received usual care. The proportion of patients with controlled BP was compared between groups at pre- and postintervention, ∼9 months later. Results and Materials: The total study population included 484 patients with mean age 60 years (range 23-102 years), 47.7% female, and 84.6% Caucasian. Mean preintervention BP was 137.8 mm Hg systolic and 81.4 mm Hg diastolic. Mean BP control rates improved for patients who received HBPM from 42% to 67% compared with matched control patients who improved from 59% to 67% (p technology has the potential to improve HTN management among patients with uncontrolled or newly diagnosed HTN. Technology needs to be easy to use and operate and would work best when integrated into local electronic health record systems. In systems without this capability, medical assistants or other personnel may be trained to facilitate the process. Nurse navigator involvement was instrumental in bridging communication between the patients and provider.

Digital control system of advanced reactor

International Nuclear Information System (INIS)

Peng Huaqing; Zhang Rui; Liu Lixin

2001-01-01

This article produced the Digital Control System For Advanced Reactor made by NPIC. This system uses Siemens SIMATIC PCS 7 process control system and includes five control system: reactor power control system, pressurizer level control system, pressurizer pressure control system, steam generator water level control system and dump control system. This system uses three automatic station to realize the function of five control system. Because the safety requisition of reactor is very strict, the system is redundant. The system configuration uses CFC and SCL. the human-machine interface is configured by Wincc. Finally the system passed the test of simulation by using RETRAN 02 to simulate the control object. The research solved the key technology of digital control system of reactor and will be very helpful for the nationalization of digital reactor control system

How to improve plant efficiency through leading plant monitoring and control system technology-Almaraz NPP Samo

International Nuclear Information System (INIS)

Garcia Rodriguez, A.; Schwee, S.M.

1994-01-01

The nuclear industry is currently faced with an intense pressure to reduce the cost of electric production. To achieve these cost reductions, utilities are changing the way they have traditionally operated. They are embracing innovative processes and systems to fundamentally change the way they have operated and maintained their plants. Plant monitoring and control technology has been instrumental in affecting these rapid and proactive changes. Our challenge is to use these new technologies in ways that improve plant reliability while lowering operation and maintenance costs. What must we do to increase operational time, improve safety and reliability while reducing all costs including fixed as well as labor? We will discuss an overall plant monitoring system vision that will allow these changes in operational practices. (Author)

NSSS Component Control System Design of Integral Reactor

International Nuclear Information System (INIS)

Lee, Joon Koo; Kwon, Ho Je; Jeong, Kwong Il; Park, Heui Youn; Koo, In Soo

2005-01-01

MMIS(Man Machine Interface System) of an integral reactor is composed of a Control Room, Plant Protection System, Control System and Monitoring System which are related with the overall plant operation. MMIS is being developed with a new design concept and digital technology to reduce the Human Factor Error and improve the systems' safety, reliability and availability. And CCS(component control system) is also being developed with a new design concept and digital hardware technology A fully digitalized system and design concept are introduced in the NSSS CCS

An Auto-Tuning PI Control System for an Open-Circuit Low-Speed Wind Tunnel Designed for Greenhouse Technology

Directory of Open Access Journals (Sweden)

Karlos Espinoza

2015-08-01

Full Text Available Wind tunnels are a key experimental tool for the analysis of airflow parameters in many fields of application. Despite their great potential impact on agricultural research, few contributions have dealt with the development of automatic control systems for wind tunnels in the field of greenhouse technology. The objective of this paper is to present an automatic control system that provides precision and speed of measurement, as well as efficient data processing in low-speed wind tunnel experiments for greenhouse engineering applications. The system is based on an algorithm that identifies the system model and calculates the optimum PI controller. The validation of the system was performed on a cellulose evaporative cooling pad and on insect-proof screens to assess its response to perturbations. The control system provided an accuracy of <0.06 m·s‾1 for airflow speed and <0.50 Pa for pressure drop, thus permitting the reproducibility and standardization of the tests. The proposed control system also incorporates a fully-integrated software unit that manages the tests in terms of airflow speed and pressure drop set points.

Soft-Fault Detection Technologies Developed for Electrical Power Systems

Science.gov (United States)

Button, Robert M.

2004-01-01

The NASA Glenn Research Center, partner universities, and defense contractors are working to develop intelligent power management and distribution (PMAD) technologies for future spacecraft and launch vehicles. The goals are to provide higher performance (efficiency, transient response, and stability), higher fault tolerance, and higher reliability through the application of digital control and communication technologies. It is also expected that these technologies will eventually reduce the design, development, manufacturing, and integration costs for large, electrical power systems for space vehicles. The main focus of this research has been to incorporate digital control, communications, and intelligent algorithms into power electronic devices such as direct-current to direct-current (dc-dc) converters and protective switchgear. These technologies, in turn, will enable revolutionary changes in the way electrical power systems are designed, developed, configured, and integrated in aerospace vehicles and satellites. Initial successes in integrating modern, digital controllers have proven that transient response performance can be improved using advanced nonlinear control algorithms. One technology being developed includes the detection of "soft faults," those not typically covered by current systems in use today. Soft faults include arcing faults, corona discharge faults, and undetected leakage currents. Using digital control and advanced signal analysis algorithms, we have shown that it is possible to reliably detect arcing faults in high-voltage dc power distribution systems (see the preceding photograph). Another research effort has shown that low-level leakage faults and cable degradation can be detected by analyzing power system parameters over time. This additional fault detection capability will result in higher reliability for long-lived power systems such as reusable launch vehicles and space exploration missions.

Nuclear materials control technology in the post-cold war world: Radiation-based methods and information management systems

International Nuclear Information System (INIS)

Tape, J.W.; Eccleston, G.W.; Ensslin, N.; Markin, J.T.

1993-01-01

The end of the cold war is providing both opportunities and requirements for improving the control of nuclear materials around the world. The dismantlement of nuclear weapons and the growth of nuclear power, including the use of plutonium in light water reactors and breeder reactor programs, coupled with enhanced proliferation concerns, drive the need for improved nuclear materials control. We describe nuclear materials control and the role of technology in making controls more effective and efficient. The current use and anticipated development in selected radiation-based methods and related information management systems am described briefly

Enhanced technologies for unattended ground sensor systems

Science.gov (United States)

Hartup, David C.

2010-04-01

Progress in several technical areas is being leveraged to advantage in Unattended Ground Sensor (UGS) systems. This paper discusses advanced technologies that are appropriate for use in UGS systems. While some technologies provide evolutionary improvements, other technologies result in revolutionary performance advancements for UGS systems. Some specific technologies discussed include wireless cameras and viewers, commercial PDA-based system programmers and monitors, new materials and techniques for packaging improvements, low power cueing sensor radios, advanced long-haul terrestrial and SATCOM radios, and networked communications. Other technologies covered include advanced target detection algorithms, high pixel count cameras for license plate and facial recognition, small cameras that provide large stand-off distances, video transmissions of target activity instead of still images, sensor fusion algorithms, and control center hardware. The impact of each technology on the overall UGS system architecture is discussed, along with the advantages provided to UGS system users. Areas of analysis include required camera parameters as a function of stand-off distance for license plate and facial recognition applications, power consumption for wireless cameras and viewers, sensor fusion communication requirements, and requirements to practically implement video transmission through UGS systems. Examples of devices that have already been fielded using technology from several of these areas are given.

Control in the ATLAS TDAQ System

CERN Document Server

Liko, D; Flammer, J; Dobson, M; Jones, R; Mapelli, L; Alexandrov, I; Korobov, S; Kotov, V; Mineev, M; Amorim, A; Fiuza de Barros, N; Klose, D; Pedro, L; Badescu, E; Caprini, M; Kolos, S; Kazarov, A; Ryabov, Yu; Soloviev, I; Computing In High Energy Physics

2005-01-01

TDAQ system requires a comprehensive and flexible control system. Its role ranges from the so-called run-control, e.g. starting and stopping the data taking, to error handling and fault tolerance. It also includes initialization and verification of the overall system. Following the traditional approach a hierarchical system of customizable controllers has been proposed. For the final system all functionality will be therefore available in a distributed manner, with the possibility of local customization. After a technology survey the open source expert system CLIPS has been chosen as a basis for the implementation of the supervision and the verification system. The CLIPS interpreter has been extended to provide a general control framework. Other ATLAS Online software components have been integrated as plug-ins and provide the mechanism for configuration and communication. Several components have been implemented sharing this technology. The dynamic behavior of the individual component is fully described by th...

Specificity of continuous auditing approach on information technology internal controls

Directory of Open Access Journals (Sweden)

Kaćanski Slobodan

2012-01-01

Full Text Available Contemporary business world, can not be imagined without the use of information technology in all aspects of business. The use of information technology in manufacturing and non-production companies' activities can greatly facilitate and accelerate the process of operation and control. Because of its complexity, they possess vulnerable areas and provide space for the emergence of accidental and intentional frauds that can significantly materially affect the business decisions made by the companies' management. Implementation of internal controls can greatly reduce the level of errors that can contribute to making the wrong decisions. In order to protect the operating system, the company's management implement an internal audit to periodically examine the fundamental quality of the internal control systems. Since the internal audit, according to its character, only periodically checks quality of internal control systems and information technologies to be reported to the manager, the problem arises in the process of in wrong time reporting the management structures of the business entity. To eliminate this problem, management implements a special approach to internal audit, called continuous auditing.

Scheduling algorithms for automatic control systems for technological processes

Science.gov (United States)

Chernigovskiy, A. S.; Tsarev, R. Yu; Kapulin, D. V.

2017-01-01

Wide use of automatic process control systems and the usage of high-performance systems containing a number of computers (processors) give opportunities for creation of high-quality and fast production that increases competitiveness of an enterprise. Exact and fast calculations, control computation, and processing of the big data arrays - all of this requires the high level of productivity and, at the same time, minimum time of data handling and result receiving. In order to reach the best time, it is necessary not only to use computing resources optimally, but also to design and develop the software so that time gain will be maximal. For this purpose task (jobs or operations), scheduling techniques for the multi-machine/multiprocessor systems are applied. Some of basic task scheduling methods for the multi-machine process control systems are considered in this paper, their advantages and disadvantages come to light, and also some usage considerations, in case of the software for automatic process control systems developing, are made.

RHIC control system

Energy Technology Data Exchange (ETDEWEB)

Barton, D.S. E-mail: dsbarton@bnl.gov; Binello, S.; Buxton, W.; Clifford, T.; D' Ottavio, T.; Hartmann, H.; Hoff, L.T.; Katz, R.; Kennell, S.; Kerner, T.; Laster, J.; Lee, R.C.; Marusic, A.; Michnoff, R.; Morris, J.; Oerter, B.R.; Olsen, R.; Piacentino, J.; Skelly, J.F

2003-03-01

The RHIC control system architecture is hierarchical and consists of two physical layers with a fiber-optic network connection. The Front-End Level systems consist of VME chassis with processors running a real-time operating system and both VME I/O modules and remote bus interfaces. Accelerator device software interfaces are implemented as objects in C++. The network implementation uses high speed, switched Ethernet technology. Specialized hardware modules were built for waveform control of power supplies, multiplexed signal acquisition, and timing services. The Console Level systems are Unix workstations. A strong emphasis has been given to developing highly reusable, standard software tools for use in building physics and diagnostic application software.

RHIC control system

International Nuclear Information System (INIS)

Barton, D.S.; Binello, S.; Buxton, W.; Clifford, T.; D'Ottavio, T.; Hartmann, H.; Hoff, L.T.; Katz, R.; Kennell, S.; Kerner, T.; Laster, J.; Lee, R.C.; Marusic, A.; Michnoff, R.; Morris, J.; Oerter, B.R.; Olsen, R.; Piacentino, J.; Skelly, J.F.

2003-01-01

The RHIC control system architecture is hierarchical and consists of two physical layers with a fiber-optic network connection. The Front-End Level systems consist of VME chassis with processors running a real-time operating system and both VME I/O modules and remote bus interfaces. Accelerator device software interfaces are implemented as objects in C++. The network implementation uses high speed, switched Ethernet technology. Specialized hardware modules were built for waveform control of power supplies, multiplexed signal acquisition, and timing services. The Console Level systems are Unix workstations. A strong emphasis has been given to developing highly reusable, standard software tools for use in building physics and diagnostic application software

Design of a study of Systems Analysis for Material Control and Accountancy Technology (SAMCAT)

International Nuclear Information System (INIS)

Persiani, P.J.; Rothman, A.B.; Bucher, R.G.; Daly, T.A.; Cha, B.C.; Trevorrow, L.E.; Seefeldt, W.B.; Stewart, W.E.

1987-01-01

The Systems Analysis for Material Control and Accountancy Technology (SAMCAT) is a program to develop an interactive computer-based management system for decision support in evaluating Material Control and Accountancy (MCandA) upgrades and for validating the MCandA aspects of the Master Safeguards and Security Agreements (MSSA) effectiveness. This paper briefly reviews SAMCAT and presents the status of current activities, with primary focus on the design of a pilot study that has been planned for the near-term development program. The objective of the pilot study is to aid in the development and testing of assessment technologies by utilizing data and information from recent upgrades in MCandA measurements at several of the measurement locations that were important contributors to the uncertainty of the inventory differences (IDs) for a specific material balance area (MBA). The FB-Line MBA in the plutonium production cycle through Savannah River was recommended as a candidate MBA for the study. Attributes considered as selection criteria of key measurement locations for MCandA upgrades, importance rankings of the measurement locations, modeling approaches in evaluating the effectiveness of upgrades at given locations, and the data requirements to support the pilot study are presented. Applications of the near-term pilot study to the overall SAMCAT development program are also presented. 2 refs., 3 figs., 1 tab

Research on control technology of hardware parallelism for marine controlled source electromagnetic transmitter

Science.gov (United States)

Wang, Meng; Deng, Ming; Luo, Xianhu; Zhao, Qingxian; Chen, Kai; Jing, Jianen

2018-02-01

The marine controlled source electromagnetic (CSEM) method has been recognized as an effective exploration method of shallow hydrocarbons around the world. We developed our own underwater marine CSEM transmitter that consisted of many functional modules with various response times. We previously adopted a centralized software-control technology to design the transmitter circuit topological structure. That structure probably generated a control disorder or malfunction. These undesirable conditions could lead to repeated recovery and deployment of the transmitter, which not only consumed time but also affected data continuity and establishment of stable and continuous CSEM field. We developed an instrument design concept named ‘control technology of hardware parallelism’. In this design, a noteworthy innovation of our new technology is to solve the above-mentioned problems at the physical and fundamental levels. We used several self-contained control-units to simultaneously accomplish the predetermined functions of the transmitter. The new solution relies on two technologies: multi-core embedded technology and multi-channel parallel optical-fiber data transmission technology. The first technology depends on many independent microcontrollers. Every microcontroller is only used to achieve a customized function. The second one relies on several multiple optical-fiber transmission channels realized by a complex programmable logic device and two optical-fiber conversion devices, which are used to establish a communication link between the shipboard monitoring and control-unit and underwater transmitter. We have conducted some marine experiments to verify the reliability and stability of the new method. In particular, the new technology used in the transmitter system could help us obtain more useful measured data in a limited time, improve real-time efficiency, and support the establishment of a stable CSEM field.

The Effect of Used Information Technology, Internal Control, and Regional Accounting System on the Performance of City Governance Agency of Banda Aceh City, Indonesia

Directory of Open Access Journals (Sweden)

Muslim Djalil

2017-07-01

Full Text Available The purpose of this research is to examine the influence of utilization of information technology, internal control system, and regional financial accounting system on the performance of city government agencies in Banda Aceh city government, Indonesia.The population of the research is 39 city government agencies (SKPK of Banda Aceh and by using the simple random sampling technique, it is selected 28 agencies within city government as a sample and employed 84 persons as respondents. The primary data of this research arecollected by using questionnaire and analyzed by using the multiple regression regresion method with a SPSS application software.The result shows that perceived by simultaneously statistical test indicated that the utilization of information technology, internal control system and implementation of regionalfinancial accounting system have a significant positive effect on the performance of city government agency. Similarly, tested partially, utilization of information technology, internalcontrol system, and implementation of the regional financial accounting system also have a significant positive effect on the performance of city government agencies in the city government of Banda Aceh, Indonesia.Keywords: Information Technology, Internal Control System, Regional Financial Accounting System, and Performance of City Governance.

Use of Soft Computing Technologies For Rocket Engine Control

Science.gov (United States)

Trevino, Luis C.; Olcmen, Semih; Polites, Michael

2003-01-01

The problem to be addressed in this paper is to explore how the use of Soft Computing Technologies (SCT) could be employed to further improve overall engine system reliability and performance. Specifically, this will be presented by enhancing rocket engine control and engine health management (EHM) using SCT coupled with conventional control technologies, and sound software engineering practices used in Marshall s Flight Software Group. The principle goals are to improve software management, software development time and maintenance, processor execution, fault tolerance and mitigation, and nonlinear control in power level transitions. The intent is not to discuss any shortcomings of existing engine control and EHM methodologies, but to provide alternative design choices for control, EHM, implementation, performance, and sustaining engineering. The approaches outlined in this paper will require knowledge in the fields of rocket engine propulsion, software engineering for embedded systems, and soft computing technologies (i.e., neural networks, fuzzy logic, and Bayesian belief networks), much of which is presented in this paper. The first targeted demonstration rocket engine platform is the MC-1 (formerly FASTRAC Engine) which is simulated with hardware and software in the Marshall Avionics & Software Testbed laboratory that

Modernization of the automation control system of technological processes at the preparation plant in the conditions of technical re-equipment

Science.gov (United States)

Lyakhovets, M. V.; Wenger, K. G.; Myshlyaev, L. P.; Shipunov, M. V.; Grachev, V. V.; Melkozerov, M. Yu; Fairoshin, Sh A.

2018-05-01

The experience of modernization of the automation control system of technological processes at the preparation plant under the conditions of technical re-equipment of the preparation plant “Barzasskoye Tovarischestvo” LLC (Berezovsky) is considered. The automated process control systems (APCS), the modernization goals and the ways to achieve them are indicated, the main subsystems of the integrated APCS are presented, the enlarged functional and technical structure of the upgraded system is given. The procedure for commissioning an upgraded system is described.

LARGE-SCALE MECURY CONTROL TECHNOLOGY TESTING FOR LIGNITE-FIRED UTILITIES-OXIDATION SYSTEMS FOR WET FGD

Energy Technology Data Exchange (ETDEWEB)

Michael J. Holmes; Steven A. Benson; Jeffrey S. Thompson

2004-03-01

The Energy & Environmental Research Center (EERC) is conducting a consortium-based effort directed toward resolving the mercury (Hg) control issues facing the lignite industry. Specifically, the EERC team--the EERC, EPRI, URS, ADA-ES, Babcock & Wilcox, the North Dakota Industrial Commission, SaskPower, and the Mercury Task Force, which includes Basin Electric Power Cooperative, Otter Tail Power Company, Great River Energy, Texas Utilities (TXU), Montana-Dakota Utilities Co., Minnkota Power Cooperative, BNI Coal Ltd., Dakota Westmoreland Corporation, and the North American Coal Company--has undertaken a project to significantly and cost-effectively oxidize elemental mercury in lignite combustion gases, followed by capture in a wet scrubber. This approach will be applicable to virtually every lignite utility in the United States and Canada and potentially impact subbituminous utilities. The oxidation process is proven at the pilot-scale and in short-term full-scale tests. Additional optimization is continuing on oxidation technologies, and this project focuses on longer-term full-scale testing. The lignite industry has been proactive in advancing the understanding of and identifying control options for Hg in lignite combustion flue gases. Approximately 1 year ago, the EERC and EPRI began a series of Hg-related discussions with the Mercury Task Force as well as utilities firing Texas and Saskatchewan lignites. This project is one of three being undertaken by the consortium to perform large-scale Hg control technology testing to address the specific needs and challenges to be met in controlling Hg from lignite-fired power plants. This project involves Hg oxidation upstream of a system equipped with an electrostatic precipitator (ESP) followed by wet flue gas desulfurization (FGD). The team involved in conducting the technical aspects of the project includes the EERC, Babcock & Wilcox, URS, and ADA-ES. The host sites include Minnkota Power Cooperative Milton R. Young

Development of technologies for national control of and accountancy for nuclear materials

International Nuclear Information System (INIS)

Choi, Young Myung; Kwack, E. H.; Kim, B. K.

2002-03-01

The aim of this project is to establish a rigid foundation of national safeguards and to develop the new technologies for the nuclear control. This project is composed of four different technologies; 1. Monitoring technology for nuclear materials, 2. Detection technology for a single particle, 3. Safeguards information management technology, 4. Physical protection technology. Various studies such as a remote verification system for CANDU spent fuel in dry storage canister, a spent fuel verification system using an optical fiber scintillator, and development of softwares for safeguards and physical protection were performed in the frist phase('99-'01). As a result of this research, it has been identified that the developed technologies could be a crucial means of the control for the nuclear material and facilities related. We are planing to accomplish a steady national safeguard system in the second phase('02-'06). This research will help to elevate the transparency and credibility in national nuclear activities by improving the relative technologies

Intelligent control and automation technology for nuclear application

International Nuclear Information System (INIS)

Kim, Jae Hee; Eom, Heung Sub; Kim, Ko Ryu; Lee, Jae Cheol; Choi, You Rak; Lee, Soo Cheol

1996-06-01

Using recent technologies on a mobile robot and computer science, we developed an automatic inspection system for weld lines of the reactor pressure vessel. The ultrasonic inspection of the reactor pressure vessel is currently performed by commercialized robot manipulators. Since, however, the conventional fixed type robot manipulator is very huge, heavy and expensive, it needs long inspection time and is hard to handle and maintain. In order to resolve these problems, we developed a new inspection automation system using a small mobile robot crawling on the vertical wall. According to the conceptual design studied in the first year, we developed the inspection automation system including an underwater inspection robot, a laser position control subsystem and a main control subsystem. And we carried out underwater experiments on the reactor vessel mockup. After finishing this project successfully, we have a plan to commercialize our inspection system. Using this system, we can expect much reduction of the inspection time, performance enhancement, automatic management of inspection history, etc. In the economic point of view, we can also expect import substitution more than 5 million dollars. The established essential technologies for intelligent control and automation are expected to be synthetically applied to the automation of similar systems in nuclear power plants. 4 tabs., 37 figs., 6 refs. (Author)

Control technology standards as foundation for production monitoring systems; Steuerungstechnische Standards als Fundament fuer die Leittechnik

Energy Technology Data Exchange (ETDEWEB)

Hirzle, Anton [Daimler AG, Mercedes-Benz Cars, Werk Sindelfingen (DE). Automatisierungstechnologie und Simulation (PWT/VAS); Alosnso Garcia, Alexander [Daimler AG, Mercedes-Benz Cars, Werk Sindelfingen (Germany). PWT/VAS, Technologiesteuerungen und Robotik; Burkhardt, Andreas [Daimler AG, Mercedes-Benz Cars, Werk Sindelfingen (Germany). PWT/VAS, Steuerungstechnik

2008-07-01

Due to increasing demands on functionality, capacity and flexibility of manufacturing facilities, the complexity in automation technology grows continuously. Daimler AG faces this development with a consistent standardisation of automation- and control technology for assembly plants. Here the standardisation strategy is composed of three consecutive phases. Main point on aimed development and standardisation of a kit out of hard- and software components is in phase 1. Phase 2 contains the standardisation on system- and application level for whole plants like body in white, paint shop and assembly. Finally the standardisation of engineering processes is the third phase. (orig.)

Intelligent Propulsion System Foundation Technology: Summary of Research

Science.gov (United States)

2008-01-01

The purpose of this cooperative agreement was to develop a foundation of intelligent propulsion technologies for NASA and industry that will have an impact on safety, noise, emissions, and cost. These intelligent engine technologies included sensors, electronics, communications, control logic, actuators, smart materials and structures, and system studies. Furthermore, this cooperative agreement helped prepare future graduates to develop the revolutionary intelligent propulsion technologies that will be needed to ensure pre-eminence of the U.S. aerospace industry. This Propulsion 21 - Phase 11 program consisted of four primary research areas and associated work elements at Ohio universities: 1.0 Turbine Engine Prognostics, 2.0 Active Controls for Emissions and Noise Reduction, 3.0 Active Structural Controls and Performance, and 4.0 System Studies and Integration. Phase l, which was conducted during the period August 1, 2003, through September 30, 2004, has been reported separately.

ETV TEST REPORT OF MOBILE SOURCE EMISSIONS CONTROL DEVICES: LUBRIZOL ENGINE CONTROL SYSTEMS PURIFILTER SC17L

Science.gov (United States)

The Environmental Technology Verification report discusses the technology and performance of the Lubrizol Engine Control Systems Purifilter SC17L manufactured by Lubrizol Engine Control Systems. The technology is a precious and base metal, passively regenerated particulate filter...

Evolution of the racetrack microtron control system

International Nuclear Information System (INIS)

Martin, E.R.; Schneider, C.M.; Martinez, V.A.; Trout, R.E.; Gritzo, R.E.

1982-01-01

Ultimately, the true measure of a control system lies in how well initial decisions allow for exigencies, as the overall machine evolves and requirements solidify. Recognizing that advances in electronic technology virtually guarantee that any system will be technologically out of date by the time it is operational, the criteria really do not involve the state of the technological advancement, but instead legitimately ask whether the control-system design can adjust to the inevitable machine-design changes, whether the operators can use it to control the machine in a reasonable manner, whether it was built within budget constraints, or, in short, whether it works. On these bases, our initial decisions on the racetrack microtron (RTM) control system have been increasingly vindicated as the system has evolved, and we feel that our experiences have shed some light on just which criteria are of real importance, and which are merely a part of the lore of popular misinformation. Unless the basic requirements are met, technical elegance is no virtue, and when they are met, design simplicity is no vice

Trends in Energy Management Technology - Part 3: State of Practiceof Energy Management, Control, and Information Systems

Energy Technology Data Exchange (ETDEWEB)

Yee, Gaymond; Webster, Tom

2004-02-01

In this report, the third in a series, we provide an evaluation of several products that exemplify the current state of practice of Energy Management, Control, and Information Systems (EMCIS). The available features for these products are summarized and analyzed with regard to emerging trends in EMCIS and potential benefits to the federal sector. The first report [1] covered enabling technologies for emerging energy management systems. The second report [2] serves as a basic reference for building control system (BCS) networking fundamentals and includes an assessment of current approaches to open communications. Part 4 of this series will discuss applications software from a user's perspective. It is important for energy managers in the Federal sector to have a high level of knowledge and understanding of these complex energy management systems. This series of reports provides energy practitioners with some basic informational and educational tools to help make decisions relative to energy management systems design, specification, procurement, and energy savings potential.

Wind Energy Conversion Systems Technology and Trends

CERN Document Server

2012-01-01

Wind Energy Conversion System covers the technological progress of wind energy conversion systems, along with potential future trends. It includes recently developed wind energy conversion systems such as multi-converter operation of variable-speed wind generators, lightning protection schemes, voltage flicker mitigation and prediction schemes for advanced control of wind generators. Modeling and control strategies of variable speed wind generators are discussed, together with the frequency converter topologies suitable for grid integration. Wind Energy Conversion System also describes offshore farm technologies including multi-terminal topology and space-based wind observation schemes, as well as both AC and DC based wind farm topologies. The stability and reliability of wind farms are discussed, and grid integration issues are examined in the context of the most recent industry guidelines. Wind power smoothing, one of the big challenges for transmission system operators, is a particular focus. Fault ride th...

Tritium system test assembly control system cost estimate

International Nuclear Information System (INIS)

Stutz, R.A.

1979-01-01

The principal objectives of the Tritium Systems Test Assembly (TSTA), which includes the development, demonstration and interfacing of technologies related to the deuterium--tritium fuel cycle for fusion reactor systems, are concisely stated. The various integrated subsystems comprising TSTA and their functions are discussed. Each of the four major subdivisions of TSTA, including the main process system, the environmental and safety systems, supporting systems and the physical plant are briefly discussed. An overview of the Master Data Acquisition and Control System, which will control all functional operation of TSTA, is provided

Large Deployable Reflector (LDR) system concept and technology definition study. Volume 2: Technology assessment and technology development plan

Science.gov (United States)

Agnew, Donald L.; Jones, Peter A.

1989-01-01

A study was conducted to define reasonable and representative LDR system concepts for the purpose of defining a technology development program aimed at providing the requisite technological capability necessary to start LDR development by the end of 1991. This volume presents thirteen technology assessments and technology development plans, as well as an overview and summary of the LDR concepts. Twenty-two proposed augmentation projects are described (selected from more than 30 candidates). The five LDR technology areas most in need of supplementary support are: cryogenic cooling; astronaut assembly of the optically precise LDR in space; active segmented primary mirror; dynamic structural control; and primary mirror contamination control. Three broad, time-phased, five-year programs were synthesized from the 22 projects, scheduled, and funding requirements estimated.

Environmental control technology

International Nuclear Information System (INIS)

Anon.

1985-01-01

During this report period, Chem Tech identified environmental control technology (ECT) as an area of emphasis for future planning and resource allocation. The Division plans to continue to perform R and D activities in ECT for external sponsors such as the DOE Office of Fossil Energy (DOE/FE), the Electric Power Research Institute (EPRI), and the Environmental Protection Agency (EPA) while striving for recognition as an R and D center for ECT within the Martin Marietta Energy Systems' Complex. Chem Tech has already played supporting roles in this area for the Y-12 Plant and the Oak Ridge Gaseous Diffusion Plant (ORGDP) and is currently expanding its support to organizations within ORNL responsible for environmental matters. Over the long term, the Division hopes to achieve recognition as a center for R and D in ECT within the wider DOE system. Recent initiatives supporting these plans are discussed below

Implementation and Analysis for APR1400 Soft Control System

International Nuclear Information System (INIS)

2015-01-01

Due to the rapid advancement of digital technology, the definite technical advantages of digital control system compared to analog control system are accelerating the implementation of advanced distributed digital control system in the nuclear power plant. One of the major advantages of digital control system is the capability of Soft Control System. The design of Soft Control System for Advanced Power Reactor 1400 (APR1400) plant of Man-Machine Interface System (MMIS) is based on full digital technologies to enhance reliability, operability and maintainability. Computer-based compact workstation has been adopted in the APR1400 Main Control Room (MCR) to provide convenient working environment. This paper introduces the approaches and methodologies of Soft Control System for the Advanced Control Room (ACR). This paper also explains major design features for operation and display of the Soft Control System and its implementation to cope with regulatory requirements. (authors)

Research on NGN network control technology

Science.gov (United States)

Li, WenYao; Zhou, Fang; Wu, JianXue; Li, ZhiGuang

2004-04-01

Nowadays NGN (Next Generation Network) is the hotspot for discussion and research in IT section. The NGN core technology is the network control technology. The key goal of NGN is to realize the network convergence and evolution. Referring to overlay network model core on Softswitch technology, circuit switch network and IP network convergence realized. Referring to the optical transmission network core on ASTN/ASON, service layer (i.e. IP layer) and optical transmission convergence realized. Together with the distributing feature of NGN network control technology, on NGN platform, overview of combining Softswitch and ASTN/ASON control technology, the solution whether IP should be the NGN core carrier platform attracts general attention, and this is also a QoS problem on NGN end to end. This solution produces the significant practical meaning on equipment development, network deployment, network design and optimization, especially on realizing present network smooth evolving to the NGN. This is why this paper puts forward the research topic on the NGN network control technology. This paper introduces basics on NGN network control technology, then proposes NGN network control reference model, at the same time describes a realizable network structure of NGN. Based on above, from the view of function realization, NGN network control technology is discussed and its work mechanism is analyzed.

Babcock & Wilcox technologies for power plant stack emissions control

Energy Technology Data Exchange (ETDEWEB)

Polster, M.; Nolan, P.S.; Batyko, R.J. [Babcock & Wilcox, Barberton, OH (United States)

1994-12-31

The current status of sulfur dioxide control in power plants is reviewed with particular emphasis on proven, commercial technologies. This paper begins with a detailed review of Babcock & Wilcox commercial wet flue gas desulfurization (FGD) systems. This is followed by a brief discussion of B&W dry FGD technologies, as well as recent full-scale and pilot-scale demonstration projects which focus on lower capital cost alternatives to conventional FGD systems. A comparison of the economics of several of these processes is also presented. Finally, technology selections resulting from recent acid rain legislation in various countries are reviewed.

USE OF UBIQUITOUS TECHNOLOGIES IN MILITARY LOGISTIC SYSTEM IN IRAN

OpenAIRE

P. Jafari; A. Sadeghi-Niaraki

2013-01-01

This study is about integration and evaluation of RFID and ubiquitous technologies in military logistic system management. Firstly, supply chain management and the necessity of a revolution in logistic systems especially in military area, are explained. Secondly RFID and ubiquitous technologies and the advantages of their use in supply chain management are introduced. Lastly a system based on these technologies for controlling and increasing the speed and accuracy in military logistic system ...

System catalytic neutralization control of combustion engines waste gases in mining technologies

Science.gov (United States)

Korshunov, G. I.; Solnitsev, R. I.

2017-10-01

The paper presents the problems solution of the atmospheric air pollution with the exhaust gases of the internal combustion engines, used in mining technologies. Such engines are used in excavators, bulldozers, dump trucks, diesel locomotives in loading and unloading processes and during transportation of minerals. NOx, CO, CH emissions as the waste gases occur during engine operation, the concentration of which must be reduced to the standard limits. The various methods and means are used for the problem solution, one of which is neutralization based on platinum catalysts. A mathematical model of a controlled catalytic neutralization system is proposed. The simulation results confirm the increase in efficiency at start-up and low engine load and the increase in the catalyst lifetime.

REVIEW OF NRC APPROVED DIGITAL CONTROL SYSTEMS ANALYSIS

International Nuclear Information System (INIS)

Markman, D.W.

1999-01-01

Preliminary design concepts for the proposed Subsurface Repository at Yucca Mountain indicate extensive reliance on modern, computer-based, digital control technologies. The purpose of this analysis is to investigate the degree to which the U. S. Nuclear Regulatory Commission (NRC) has accepted and approved the use of digital control technology for safety-related applications within the nuclear power industry. This analysis reviews cases of existing digitally-based control systems that have been approved by the NRC. These cases can serve as precedence for using similar types of digitally-based control technologies within the Subsurface Repository. While it is anticipated that the Yucca Mountain Project (YMP) will not contain control systems as complex as those required for a nuclear power plant, the review of these existing NRC approved applications will provide the YMP with valuable insight into the NRCs review process and design expectations for safety-related digital control systems. According to the YMP Compliance Program Guidance, portions of various NUREGS, Regulatory Guidelines, and nuclear IEEE standards the nuclear power plant safety related concept would be applied to some of the designs on a case-by-case basis. This analysis will consider key design methods, capabilities, successes, and important limitations or problems of selected control systems that have been approved for use in the Nuclear Power industry. An additional purpose of this analysis is to provide background information in support of further development of design criteria for the YMP. The scope and primary objectives of this analysis are to: (1) Identify and research the extent and precedence of digital control and remotely operated systems approved by the NRC for the nuclear power industry. Help provide a basis for using and relying on digital technologies for nuclear related safety critical applications. (2) Identify the basic control architecture and methods of key digital control

Applications of CELSS technology to controlled environment agriculture

Science.gov (United States)

Bates, Maynard E.; Bubenheim, David L.

1991-01-01

Controlled environment agriculture (CEA) is defined as the use of environmental manipulation for the commercial production of organisms, whether plants or animals. While many of the technologies necessary for aquaculture systems in North America is nevertheless doubling approximately every five years. Economic, cultural, and environmental pressures all favor CEA over field production for many non-commodity agricultural crops. Many countries around the world are already dependent on CEA for much of their fresh food. Controlled ecological life support systems (CELSS), under development at ARC, KSC, and JSC expand the concept of CEA to the extent that all human requirements for food, oxygen, and water will be provided regenerated by processing of waste streams to supply plant inputs. The CELSS will likely contain plants, humans, possibly other animals, microorganisms and physically and chemical processors. In effect, NASA will create engineered ecosystems. In the process of developing the technology for CELSS, NASA will develop information and technology which will be applied to improving the efficiency, reliability, and cost effectiveness for CEA, improving its resources recycling capabilities, and lessening its environmental impact to negligible levels.

RESEARCH AREA -- ARTIFICIAL INTELLIGENCE CONTROL (AIR POLLUTION TECHNOLOGY BRANCH, AIR POLLUTION PREVENTION AND CONTROL DIVISION, NRMRL)

Science.gov (United States)

The Air Pollution Technology Branch (APTB) of NRMRL's Air Pollution Prevention and Control Division in Research Triangle Park, NC, has conducted several research projects for evaluating the use of artificial intelligence (AI) to improve the control of pollution control systems an...

Spacecraft momentum control systems

CERN Document Server

Leve, Frederick A; Peck, Mason A

2015-01-01

The goal of this book is to serve both as a practical technical reference and a resource for gaining a fuller understanding of the state of the art of spacecraft momentum control systems, specifically looking at control moment gyroscopes (CMGs). As a result, the subject matter includes theory, technology, and systems engineering. The authors combine material on system-level architecture of spacecraft that feature momentum-control systems with material about the momentum-control hardware and software. This also encompasses material on the theoretical and algorithmic approaches to the control of space vehicles with CMGs. In essence, CMGs are the attitude-control actuators that make contemporary highly agile spacecraft possible. The rise of commercial Earth imaging, the advances in privately built spacecraft (including small satellites), and the growing popularity of the subject matter in academic circles over the past decade argues that now is the time for an in-depth treatment of the topic. CMGs are augmented ...

ISABELLE control system: design concepts

International Nuclear Information System (INIS)

Humphrey, J.W.

1979-01-01

ISABELLE is a Department of Energy funded proton accelerator/storage ring being built at Brookhaven National Laboratory (Upton, Long Island, New York). It is large (3.8 km circumference) and complicated (approx. 30,000 monitor and control variables). It is based on superconducting technology. Following the example of previous accelerators, ISABELLE will be operated from a single control center. The control system will be distributed and will incorporate a local computer network. An overview of the conceptual design of the ISABELLE control system will be presented

Recommended Practice: Creating Cyber Forensics Plans for Control Systems

Energy Technology Data Exchange (ETDEWEB)

Eric Cornelius; Mark Fabro

2008-08-01

Cyber forensics has been in the popular mainstream for some time, and has matured into an information-technology capability that is very common among modern information security programs. The goal of cyber forensics is to support the elements of troubleshooting, monitoring, recovery, and the protection of sensitive data. Moreover, in the event of a crime being committed, cyber forensics is also the approach to collecting, analyzing, and archiving data as evidence in a court of law. Although scalable to many information technology domains, especially modern corporate architectures, cyber forensics can be challenging when being applied to non-traditional environments, which are not comprised of current information technologies or are designed with technologies that do not provide adequate data storage or audit capabilities. In addition, further complexity is introduced if the environments are designed using proprietary solutions and protocols, thus limiting the ease of which modern forensic methods can be utilized. The legacy nature and somewhat diverse or disparate component aspects of control systems environments can often prohibit the smooth translation of modern forensics analysis into the control systems domain. Compounded by a wide variety of proprietary technologies and protocols, as well as critical system technologies with no capability to store significant amounts of event information, the task of creating a ubiquitous and unified strategy for technical cyber forensics on a control systems device or computing resource is far from trivial. To date, no direction regarding cyber forensics as it relates to control systems has been produced other than what might be privately available from commercial vendors. Current materials have been designed to support event recreation (event-based), and although important, these requirements do not always satisfy the needs associated with incident response or forensics that are driven by cyber incidents. To address these

Delegation control of multiple unmanned systems

Science.gov (United States)

Flaherty, Susan R.; Shively, Robert J.

2010-04-01

Maturing technologies and complex payloads coupled with a future objective to reduce the logistics burden of current unmanned aerial systems (UAS) operations require a change to the 2-crew employment paradigm. Increased automation and operator supervisory control of unmanned systems have been advocated to meet the objective of reducing the crew requirements, while managing future technologies. Specifically, a delegation control employment strategy has resulted in reduced workload and higher situation awareness for single operators controlling multiple unmanned systems in empirical studies1,2. Delegation control is characterized by the ability for an operator to call a single "play" that initiates prescribed default actions for each vehicle and associated sensor related to a common mission goal. Based upon the effectiveness of delegation control in simulation, the U.S. Army Aeroflightdynamics Directorate (AFDD) developed a Delegation Control (DelCon) operator interface with voice recognition implementation for play selection, real-time play modification, and play status with automation transparency to enable single operator control of multiple unmanned systems in flight. AFDD successfully demonstrated delegation control in a Troops-in-Contact mission scenario at Ft. Ord in 2009. This summary showcases the effort as a beneficial advance in single operator control of multiple UAS.

Water pollution control technology in Japan

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-11-01

This work is a compilation by members of the Committee for Studying Transfer of Environmental Technology on the expertise and technology developed by the members for controlling water pollution in Japan, together with consideration of issues concerning the transfer of environmental technologies to developing countries. The committee is composed of representatives for the Environment Agency, Japan, Osaka Prefectural Government, Osaka Municipal Government, and 25 companies such as manufacturers of environmental equipment. The document contains a total of 93 short papers grouped into sections on: industrial wastewater treatment; sewage treatment; right soil treatment; sludge treatment; and miscellaneous. One paper by the Kausai Electric Power Co., Inc., discusses waste water treatment systems in oil-fired thermal power plants; another describes an internally circulating fluidized bed boiler for cocombusting coal with industrial wastes.

Automating the control of robotic systems in unstructured environments

International Nuclear Information System (INIS)

Harrigan, R.W.

1993-01-01

The US Department Energy's Office of Technology Development has sponsored the development of generic robotics technologies for application to a wide range of remote systems. Of primary interest is the development of technologies which enable faster, safer, and cheaper cleanup of hazardous waste sites than is possible using conventional human contact or remote manual approaches. The development of model-based sensor-directed robot control approaches supports these goals by developing modular control technologies which reduce the time and cost of development by allowing reuse of control system software. In addition, the use of computer models improves the safety of remote site cleanup by allowing automated errors detection and recovery while reducing the time for technology development

Review of Literature on Terminal Box Control, Occupancy Sensing Technology and Multi-zone Demand Control Ventilation (DCV)

Energy Technology Data Exchange (ETDEWEB)

Liu, Guopeng; Dasu, Aravind R.; Zhang, Jian

2012-03-01

This report presents an overall review of the standard requirement, the terminal box control, occupancy sensing technology and DCV. There is system-specific guidance for single-zone systems, but DCV application guidance for multi-zone variable air volume (VAV) systems is not available. No real-world implementation case studies have been found using the CO2-based DCV. The review results also show that the constant minimum air flow set point causes excessive fan power consumption and potential simultaneous heating and cooling. Occupancy-based control (OBC) is needed for the terminal box in order to achieve deep energy savings. Key to OBC is a technology for sensing the actual occupancy of the zone served in real time. Several technologies show promise, but none currently fully meets the need with adequate accuracy and sufficiently low cost.

Control and monitoring systems for electron beam flue gas treatment technology

International Nuclear Information System (INIS)

Chmielewski, A.G.; Licki, J.; Mazurekc, J.; Nelskic, L.; Sobolewskic, L.

2011-01-01

The reliable and accurate measurements of gas parameters in essential points of industrial plant are necessary for its proper operation and control. Natural flue gases there are only at the inlet. At other points of plant gas parameters are strongly modified by process control system. The principal role of process monitoring system is to provide the Computer System for Monitoring and Control with continuous recording of process parameters. The main goal of control system is to obtain the optimal SO 2 and NO x removal efficiencies by control of amount of spray water at the spray cooler, amount of NH 3 injection to flue gas and adjustment of electron beam current. The structure of the process control system is based on algorithms describing functional dependence of SO 2 and NO x removal efficiencies. The best available techniques should be applied for measurements of flue gases parameters at essential points of installation and for digital control system to assist plant operators in the analysis and optimization of plant operation, including integrated emission control. (author)

Control and monitoring systems for electron beam flue gas treatment technology

Energy Technology Data Exchange (ETDEWEB)

Chmielewski, A. G. [Institute of Nuclear Chemistry and Technology, Warsaw (Poland); Licki, J. [Institute of Atomic Energy, Otwock-Świerk (Poland); Mazurekc, J.; Nelskic, L.; Sobolewskic, L. [Dolna Odra Group, Pomorzany Power Plant, Szczecin (Poland)

2011-07-01

The reliable and accurate measurements of gas parameters in essential points of industrial plant are necessary for its proper operation and control. Natural flue gases there are only at the inlet. At other points of plant gas parameters are strongly modified by process control system. The principal role of process monitoring system is to provide the Computer System for Monitoring and Control with continuous recording of process parameters. The main goal of control system is to obtain the optimal SO{sub 2} and NO{sub x} removal efficiencies by control of amount of spray water at the spray cooler, amount of NH{sub 3} injection to flue gas and adjustment of electron beam current. The structure of the process control system is based on algorithms describing functional dependence of SO{sub 2} and NO{sub x} removal efficiencies. The best available techniques should be applied for measurements of flue gases parameters at essential points of installation and for digital control system to assist plant operators in the analysis and optimization of plant operation, including integrated emission control. (author)

Advanced Instrumentation, Information, and Control Systems Technologies Pathway: FY 2016 External Review

Energy Technology Data Exchange (ETDEWEB)

Thomas, Kenneth David [Idaho National Lab. (INL), Idaho Falls, ID (United States); Hallbert, Bruce Perry [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-11-01

This report describes an External Review conducted by the LWRS Program Advanced Instrumentation, Information, and Control (II&C) Systems Technologies Pathway to solicit feedback on the topics and results of the ongoing II&C research program. This review was held in conjunction with the Nuclear Energy Institute (NEI) Digital I&C Working Group meeting that was held at Idaho National Laboratory (INL) on August 9-10, 2016. Given the opportunity to visit INL and see the pathway research projects, NEI agreed that the Working Group would serve as the External Review panel for the purpose of obtaining expert input on the value and timing of the research projects. This consisted of demonstrations in the Human Systems Simulation Laboratory followed by presentations on the II&C research program in general as well as the five technology development areas. Following the meeting, the presentations were sent to each of the attendees so they could review them in more detail and refer to them in completing the feedback form. Follow-up activities were conducted with the attendees following the meeting to obtain the completed feedback forms. A total of 13 forms were returned. The feedback forms were reviewed by the pathway to compile the data and comments received, which are documented in the report. In all, the feedback provided by the External Review participants is taken to be a strong endorsement of the types of projects being conducted by the pathway, the value they hold for the nuclear plants, and the general timing of need. The feedback aligns well with the priorities, levels of efforts allocated for the research projects, and project schedules. The feedback also represents realistic observations on the practicality of some aspects of implementing these technologies. In some cases, the participants provided thoughtful challenges to certain assumptions in the formulation of the technologies or in deployment plans. These deserve further review and revision of plans if warranted

Advanced Instrumentation, Information, and Control Systems Technologies Pathway: FY 2016 External Review

International Nuclear Information System (INIS)

Thomas, Kenneth David; Hallbert, Bruce Perry

2016-01-01

This report describes an External Review conducted by the LWRS Program Advanced Instrumentation, Information, and Control (II&C) Systems Technologies Pathway to solicit feedback on the topics and results of the ongoing II&C research program. This review was held in conjunction with the Nuclear Energy Institute (NEI) Digital I&C Working Group meeting that was held at Idaho National Laboratory (INL) on August 9-10, 2016. Given the opportunity to visit INL and see the pathway research projects, NEI agreed that the Working Group would serve as the External Review panel for the purpose of obtaining expert input on the value and timing of the research projects. This consisted of demonstrations in the Human Systems Simulation Laboratory followed by presentations on the II&C research program in general as well as the five technology development areas. Following the meeting, the presentations were sent to each of the attendees so they could review them in more detail and refer to them in completing the feedback form. Follow-up activities were conducted with the attendees following the meeting to obtain the completed feedback forms. A total of 13 forms were returned. The feedback forms were reviewed by the pathway to compile the data and comments received, which are documented in the report. In all, the feedback provided by the External Review participants is taken to be a strong endorsement of the types of projects being conducted by the pathway, the value they hold for the nuclear plants, and the general timing of need. The feedback aligns well with the priorities, levels of efforts allocated for the research projects, and project schedules. The feedback also represents realistic observations on the practicality of some aspects of implementing these technologies. In some cases, the participants provided thoughtful challenges to certain assumptions in the formulation of the technologies or in deployment plans. These deserve further review and revision of plans if warranted

Airborne radioactive emission control technology. Volume II

International Nuclear Information System (INIS)

Skoski, L.; Berlin, R.; Corby, D.; Clancy, J.; Hoopes, G.

1980-03-01

This report reviews the current and future control technology for airborne emissions from a wide variety of industries/facilities, including uranium mining and milling, other nuclear fuel cycle facilities, other NRC-licensed and DOE facilities, fossil fuel facilities, selected metal and non-metal extraction industries, and others. Where specific radioactivity control technology is lacking, a description of any existing control technology is given. Future control technology is assessed in terms of improvements to equipment performance and process alterations. A catalogue of investigated research on advanced control technologies is presented

Airborne radioactive emission control technology. Volume III

International Nuclear Information System (INIS)

Skoski, L.; Berlin, R.; Corby, D.; Clancy, J.; Hoopes, G.

1980-03-01

This report reviews the current and future control technology for airborne emissions from a wide variety of industries/facilities, including uranium mining and milling, other nuclear fuel cycle facilities, other NRC-licensed and DOE facilities, fossil fuel facilities, selected metal and non-metal extraction industries, and others. Where specific radioactivity control technology is lacking, a description of any existing control technology is given. Future control technology is assessed in terms of improvements to equipment performance and process alterations. A catalogue of investigated research on advanced control technologies is presented

Airborne radioactive emission control technology. Volume I

International Nuclear Information System (INIS)

Skoski, L.; Berlin, R.; Corby, D.; Clancy, J.; Hoopes, G.

1980-03-01

This report reviews the current and future control technology for airborne emissions from a wide variety of industries/facilities, includimg uranium mining and milling, other nuclear fuel cycle facilities, other NRC-licensed and DOE facilities, fossil fuel facilities, selected metal and non-metal extraction industries, and others. Where specific radioactivity control technology is lacking a description of any existing control technology is given. Future control technology is assessed in terms of improvements to equipment performance and process alterations. A catalogue of investigated research on advanced control technologies is presented

F-15 IFCS: Intelligent Flight Control System

Science.gov (United States)

Bosworth, John

2007-01-01

This viewgraph presentation describes the F-15 Intelligent Flight Control System (IFCS). The goals of this project include: 1) Demonstrate revolutionary control approaches that can efficiently optimize aircraft performance in both normal and failure conditions; and 2) Demonstrate advance neural network-based flight control technology for new aerospace systems designs.

Integration of advanced teleoperation technologies for control of space robots

Science.gov (United States)

Stagnaro, Michael J.

1993-01-01

Teleoperated robots require one or more humans to control actuators, mechanisms, and other robot equipment given feedback from onboard sensors. To accomplish this task, the human or humans require some form of control station. Desirable features of such a control station include operation by a single human, comfort, and natural human interfaces (visual, audio, motion, tactile, etc.). These interfaces should work to maximize performance of the human/robot system by streamlining the link between human brain and robot equipment. This paper describes development of a control station testbed with the characteristics described above. Initially, this testbed will be used to control two teleoperated robots. Features of the robots include anthropomorphic mechanisms, slaving to the testbed, and delivery of sensory feedback to the testbed. The testbed will make use of technologies such as helmet mounted displays, voice recognition, and exoskeleton masters. It will allow tor integration and testing of emerging telepresence technologies along with techniques for coping with control link time delays. Systems developed from this testbed could be applied to ground control of space based robots. During man-tended operations, the Space Station Freedom may benefit from ground control of IVA or EVA robots with science or maintenance tasks. Planetary exploration may also find advanced teleoperation systems to be very useful.

Controleum - an independently extensible control system

DEFF Research Database (Denmark)

Jensen, Martin Lykke Rytter

2014-01-01

challenging kind of system to design for independent extension. This thesis presents two new software technologies that improve the extensibility of control systems: First, the concept of dynamic links is introduced and Decouplink – an implementation of dynamic links for Java - is presented. Dynamic links...... is introduced, and an implementation is presented. The extensible controller is a component framework designed to automatically resolve conflicts among mutually unaware components in a control system. The solution is based on the idea that independent components implement different kinds of control concerns...

Engineering Design of ITER Prototype Fast Plant System Controller

Science.gov (United States)

Goncalves, B.; Sousa, J.; Carvalho, B.; Rodrigues, A. P.; Correia, M.; Batista, A.; Vega, J.; Ruiz, M.; Lopez, J. M.; Rojo, R. Castro; Wallander, A.; Utzel, N.; Neto, A.; Alves, D.; Valcarcel, D.

2011-08-01

The ITER control, data access and communication (CODAC) design team identified the need for two types of plant systems. A slow control plant system is based on industrial automation technology with maximum sampling rates below 100 Hz, and a fast control plant system is based on embedded technology with higher sampling rates and more stringent real-time requirements than that required for slow controllers. The latter is applicable to diagnostics and plant systems in closed-control loops whose cycle times are below 1 ms. Fast controllers will be dedicated industrial controllers with the ability to supervise other fast and/or slow controllers, interface to actuators and sensors and, if necessary, high performance networks. Two prototypes of a fast plant system controller specialized for data acquisition and constrained by ITER technological choices are being built using two different form factors. This prototyping activity contributes to the Plant Control Design Handbook effort of standardization, specifically regarding fast controller characteristics. Envisaging a general purpose fast controller design, diagnostic use cases with specific requirements were analyzed and will be presented along with the interface with CODAC and sensors. The requirements and constraints that real-time plasma control imposes on the design were also taken into consideration. Functional specifications and technology neutral architecture, together with its implications on the engineering design, were considered. The detailed engineering design compliant with ITER standards was performed and will be discussed in detail. Emphasis will be given to the integration of the controller in the standard CODAC environment. Requirements for the EPICS IOC providing the interface to the outside world, the prototype decisions on form factor, real-time operating system, and high-performance networks will also be discussed, as well as the requirements for data streaming to CODAC for visualization and

Generation of control sequences for a pilot-disassembly system

Science.gov (United States)

Seliger, Guenther; Kim, Hyung-Ju; Keil, Thomas

2002-02-01

Closing the product and material cycles has emerged as a paradigm for industry in the 21st century. Disassembly plays a key role in a life cycle economy since it enables the recovery of resources. A partly automated disassembly system should adapt to a large variety of products and different degrees of devaluation. Also the amounts of products to be disassembled can vary strongly. To cope with these demands an approach to generate on-line disassembly control sequences will be presented. In order to react on these demands the technological feasibility is considered within a procedure for the generation of disassembly control sequences. Procedures are designed to find available and technologically feasible disassembly processes. The control system is formed by modularised and parameterised control units in the cell level within the entire control architecture. In the first development stage product and process analyses at the sample product washing machine were executed. Furthermore a generalized disassembly process was defined. Afterwards these processes were structured in primary and secondary functions. In the second stage the disassembly control at the technological level was investigated. Factors were the availability of the disassembly tools and the technological feasibility of the disassembly processes within the disassembly system. Technical alternative disassembly processes are determined as a result of availability of the tools and technological feasibility of processes. The fourth phase was the concept for the generation of the disassembly control sequences. The approach will be proved in a prototypical disassembly system.

EVALUATION OF BEST AVAILABLE CONTROL TECHNOLOGY FOR TOXICS (TBACT) DOUBLE SHELL TANK FARMS PRIMARY VENTILATION SYSTEM SUPPORTING WASTE TRANSFER OPERATIONS

International Nuclear Information System (INIS)

Kelly, S.E.; Haass, C.C.; Kovach, J.L.; Turner, D.A.

2010-01-01

This report is an evaluation of Best Available Control Technology for Toxics (tBACT) for installation and operation of the Hanford double shell (DST) tank primary ventilation systems. The DST primary ventilation systems are being modified to support Hanford's waste retrieval, mixing, and delivery of single shell tank (SST) and DST waste through out the DST storage system to the Waste Treatment and Immobilization Plant (WTP).

EVALUATION OF BEST AVAILABLE CONTROL TECHNOLOGY FOR TOXICS (TBACT) DOUBLE SHELL TANK FARMS PRIMARY VENTILATION SYSTEMS SUPPORTING WASTE TRANSFER OPERATIONS

International Nuclear Information System (INIS)

Haas, C.C.; Kovach, J.L.; Kelly, S.E.; Turner, D.A.

2010-01-01

This report is an evaluation of Best Available Control Technology for Toxics (tBACT) for installation and operation of the Hanford double shell (DST) tank primary ventilation systems. The DST primary ventilation systems are being modified to support Hanford's waste retrieval, mixing, and delivery of single shell tank (SST) and DST waste through the DST storage system to the Waste Treatment and Immobilization Plant (WTP).

EVALUATION OF BEST AVAILABLE CONTROL TECHNOLOGY FOR TOXICS (TBACT) DOUBLE SHELL TANK FARMS PRIMARY VENTILATION SYSTEM SUPPORTING WASTE TRANSFER OPERATIONS

Energy Technology Data Exchange (ETDEWEB)

KELLY SE; HAASS CC; KOVACH JL; TURNER DA

2010-06-03

This report is an evaluation of Best Available Control Technology for Toxics (tBACT) for installation and operation of the Hanford double shell (DST) tank primary ventilation systems. The DST primary ventilation systems are being modified to support Hanford's waste retrieval, mixing, and delivery of single shell tank (SST) and DST waste throught the DST storage system to the Waste Treatment and Immobilization Plant (WTP).

EVALUATION OF BEST AVAILABLE CONTROL TECHNOLOGY FOR TOXICS -TBACT- DOUBLE SHELL TANK FARMS PRIMARY VENTILATION SYSTEMS SUPPORTING WASTE TRANSFER OPERATIONS

Energy Technology Data Exchange (ETDEWEB)

HAAS CC; KOVACH JL; KELLY SE; TURNER DA

2010-06-24

This report is an evaluation of Best Available Control Technology for Toxics (tBACT) for installation and operation of the Hanford double shell (DST) tank primary ventilation systems. The DST primary ventilation systems are being modified to support Hanford's waste retrieval, mixing, and delivery of single shell tank (SST) and DST waste through the DST storage system to the Waste Treatment and Immobilizaiton Plant (WTP).

FOOD SAFETY CONTROL SYSTEM IN CHINA

Institute of Scientific and Technical Information of China (English)

Liu Wei-jun; Wei Yi-min; Han Jun; Luo Dan; Pan Jia-rong

2007-01-01

Most countries have expended much effort to develop food safety control systems to ensure safe food supplies within their borders. China, as one of the world's largest food producers and consumers,pays a lot of attention to food safety issues. In recent years, China has taken actions and implemented a series of plans in respect to food safety. Food safety control systems including regulatory, supervisory,and science and technology systems, have begun to be established in China. Using, as a base, an analysis of the current Chinese food safety control system as measured against international standards, this paper discusses the need for China to standardize its food safety control system. We then suggest some policies and measures to improve the Chinese food safety control system.

Open modular architecture controls at GM Powertrain: technology and implementation

Science.gov (United States)

Bailo, Clark P.; Yen, C. J.

1997-01-01

General Motors Powertrain Group (GMPTG) has been the leader in implementing open, modular architecture controller (OMAC) technologies in its manufacturing applications since 1986. The interest in OMAC has been greatly expanded for the past two years because of the advancement of personal computer technologies and the publishing of the OMAC whitepaper by the US automotive companies stating the requirements of OMAC technologies in automotive applications. The purpose of this paper is to describe the current OMAC projects and the future direction of implementation at GMPTG. An overview of the OMAC project and the definition of the OMAC concept are described first. The rationale of pursuing open technologies is explained from the perspective of GMPTG in lieu of its agile manufacturing strategy. Examples of existing PC-based control applications are listed to demonstrate the extensive commitment to PC-based technologies that has already been put in place. A migration plan form PC-based to OMAC-based systems with the thorough approach of validation are presented next to convey the direction that GMPTG is taking in implementing OMAC technologies. Leveraged technology development projects are described to illustrate the philosophy and approaches toward the development of OMAC technologies at GMPTG. Finally, certain implementation issues are discussed to emphasize efforts that are still required to have successful implementations of OMAC systems.

Air pollution control technologies and their interactions

Energy Technology Data Exchange (ETDEWEB)

Nalbandian, H. [IEA Clean Coal Centre, London (United Kingdom)

2004-11-01

A large number of coal-fired power stations have been fitted/retrofitted with dedicated air pollutant control technologies. Experience shows that these technologies can have complex interactions and can impact each other as well as balance of plant, positively and/or negatively. Particulate matter (PM) is usually captured with electrostatic precipitators (ESPs) and fabric filters (FF). These technologies are efficient and reliable but their performance may be affected by modifying operating conditions and introducing primary measures for NOx reduction. Flue gas desulphurisation (FGD) systems for SO{sub 2} control have been installed in many facilities with the most popular technology being the wet limestone/gypsum scrubber. FGD use can decrease particulate matter and mercury emissions which is a major issue in the USA, cause an increase in carbon dioxide emissions, and in solids by-product. Primary measures such as low NOx burners (LNBs) and overfire air (OFA) minimise NOx formation but can increase carbon in ash (CIA) which can cause problems with fly ash sales but may also improve mercury capture. Reducing NOx emissions with selective catalytic reduction (SCR) can result in a decrease in particulate matter, an increase in SO{sub 3} emissions and trace increase in NH{sub 3}. This can cause fouling and loss of performance of the air preheater, due to the formation of ammonium sulphates. One way of alleviating this is improved soot-blowing and other cleaning capabilities. This report studies these and other interactions between existing air pollution control technologies in pulverised coal fired power plants. 249 refs., 13 figs., 18 tabs.

Field Operations and Enforcement Manual for Air Pollution Control. Volume II: Control Technology and General Source Inspection.

Science.gov (United States)

Weisburd, Melvin I.

The Field Operations and Enforcement Manual for Air Pollution Control, Volume II, explains in detail the following: technology of source control, modification of operations, particulate control equipment, sulfur dioxide removal systems for power plants, and control equipment for gases and vapors; inspection procedures for general sources, fuel…

Scientific-technical level of developments of technological process control and management systems. Modeling of processes of defective fuel pellets formation

International Nuclear Information System (INIS)

Troshchenko, V.G.

2005-01-01

Automation section of the Institute SverdNIIkhimmash is founded for development of management systems for equipment being created in the Institute and for providing of the systems by optional facilities for control and automation. To solve these problems the section takes part in investigations of technological units as objects of automation with mathematical models working out [ru

National Renewable Energy Laboratory (NREL) Topic 2 Final Report: End-to-End Communication and Control System to Support Clean Energy Technologies

Energy Technology Data Exchange (ETDEWEB)

Hudgins, Andrew P. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Carrillo, Ismael M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jin, Xin [National Renewable Energy Lab. (NREL), Golden, CO (United States); Simmins, John [Electric Power Research Inst. (EPRI), Palo Alto, CA (United States)

2018-02-21

This document is the final report of a two-year development, test, and demonstration project, 'Cohesive Application of Standards- Based Connected Devices to Enable Clean Energy Technologies.' The project was part of the National Renewable Energy Laboratory's (NREL's) Integrated Network Testbed for Energy Grid Research and Technology (INTEGRATE) initiative hosted at Energy Systems Integration Facility (ESIF). This project demonstrated techniques to control distribution grid events using the coordination of traditional distribution grid devices and high-penetration renewable resources and demand response. Using standard communication protocols and semantic standards, the project examined the use cases of high/low distribution voltage, requests for volt-ampere-reactive (VAR) power support, and transactive energy strategies using Volttron. Open source software, written by EPRI to control distributed energy resources (DER) and demand response (DR), was used by an advanced distribution management system (ADMS) to abstract the resources reporting to a collection of capabilities rather than needing to know specific resource types. This architecture allows for scaling both horizontally and vertically. Several new technologies were developed and tested. Messages from the ADMS based on the common information model (CIM) were developed to control the DER and DR management systems. The OpenADR standard was used to help manage grid events by turning loads off and on. Volttron technology was used to simulate a homeowner choosing the price at which to enter the demand response market. Finally, the ADMS used newly developed algorithms to coordinate these resources with a capacitor bank and voltage regulator to respond to grid events.

INFORMATION SYSTEM QUALITY CONTROL KNOWLEDGE

Directory of Open Access Journals (Sweden)

Vladimir Nikolaevich Babeshko

2017-02-01

Full Text Available The development of the educational system is associated with the need to control the quality of educational services. Quality control knowledge is an important part of the scientific process. The penetration of computers into all areas of activities changing approaches and technologies that previously they were used.

Automatic Energy Control And Monitoring System For Building

Directory of Open Access Journals (Sweden)

Hnin Nu Thaung

2015-08-01

Full Text Available The use of smart home technology in the home or building offers significant potential for energy savings. In this paper an energy management system based on wireless sensor networks. The proposed system is composed of two main components a wireless sensor network and monitoring terminal. Wireless sensors are used for sensing and transmitting electricity data and remote monitoring and control of appliances are provided to users through computer. The system enables users to save energy by monitoring and controlling appliances through terminal. This paper gives an overview of sensor technology and wireless networks in the development of an intelligent energy management system for buildings. This technology has ample potential to change the way live and work. ZigBee is used as a communication medium in building intelligent energy management system in this paper. From the prototype setup it is shown that ZigBee is a suitable technology to be adopted as the communication infrastructure in energy management system for buildings .The proposed system can be installed and maintained in residential environments with ease.

2nd International Conference on Electrical Systems, Technology and Information 2015

CERN Document Server

Tanoto, Yusak; Lim, Resmana; Santoso, Murtiyanto; Pah, Nemuel

2016-01-01

This book includes the original, peer-reviewed research papers from the 2nd International Conference on Electrical Systems, Technology and Information (ICESTI 2015), held in September 2015 at Patra Jasa Resort & Villas Bali, Indonesia. Topics covered include: Mechatronics and Robotics, Circuits and Systems, Power and Energy Systems, Control and Industrial Automation, and Information Theory.    It explores emerging technologies and their application in a broad range of engineering disciplines, including communication technologies and smart grids. It examines hybrid intelligent and knowledge-based control, embedded systems, and machine learning. It also presents emerging research and recent application in green energy system and storage. It discusses the role of electrical engineering in biomedical, industrial and mechanical systems, as well as multimedia systems and applications, computer vision and image and signal processing. The primary objective of this series is to provide references for disseminat...

Neutral beam control systems for the Tandem Mirror Experiment

International Nuclear Information System (INIS)

Ross, R.I.

1979-01-01

The Tandem Mirror Experiment (TMX) is presently developing the technology and approaches which will be used in larger fusion systems. This paper describes some of the designs which were used in creating the control system for the TMX neutral beams. To create a system of controls that would work near these large, rapid switching current sources required a mixture of different technologies: fiberoptic data transmission, printed circuit and wirewrap techniques, etc

GLCTA control system

International Nuclear Information System (INIS)

Terunuma, N.; Hayano, H.; Higo, T.; Saeki, T.; Suehara, T.; Watanabe, K.

2004-01-01

Research and development for the high power X-band RF technologies have been performed on the GLC Test Accelerator, GLCTA, since fall of 2003. The control system of this facility is based on the PC-Linux servers that handle the CAMAC, VME and PLC modules. Automated RF processing and data accumulation of the RF breakdown have been performed. (author)

Avionics systems integration technology

Science.gov (United States)

Stech, George; Williams, James R.

1988-01-01

A very dramatic and continuing explosion in digital electronics technology has been taking place in the last decade. The prudent and timely application of this technology will provide Army aviation the capability to prevail against a numerically superior enemy threat. The Army and NASA have exploited this technology explosion in the development and application of avionics systems integration technology for new and future aviation systems. A few selected Army avionics integration technology base efforts are discussed. Also discussed is the Avionics Integration Research Laboratory (AIRLAB) that NASA has established at Langley for research into the integration and validation of avionics systems, and evaluation of advanced technology in a total systems context.

Overview: Applicability of U.S. environmental control technologies for Korea

Energy Technology Data Exchange (ETDEWEB)

Chun, S.W. [DOE Pittsburgh Energy Technology Center, PA (United States)

1994-12-31

A review of the applicability of US environmental control technologies for Korea is presented in outline form. The following topics are discussed: PETC coal research activities, environmental costs, environmental challenges, Clean Air Act requirements, additional regulations for air toxics, clean coal technologies (CCT) approach, CCT help meet environmental challenges, utility options, research goals for advanced power systems, PETC Programs, the NO{sub x} SO process, flue gas cleanup program, air toxics emissions, and retrofit NO{sub x} control for coal-burning boilers.

JT-60 plasma control system

International Nuclear Information System (INIS)

Kurihara, K.

1988-01-01

JT-60 plasma control can be performed by the supervisory controller, the measurement system and actuators such as the poloidal field coil power supplies, gas injectors, neutral beam injection (NBI) heating system and radio frequency (RF) heating system. One of the most important characteristics of this system is a perfect digital control one composed of mini-computers, fast array processors and CAMAC modules, and it has large flexibility and few troubles to adjust the system. This system started to be operated in April 1985, after the six-year-long design, construction and testing, and have been operated and improved many times for two years. In this paper, the final system specification and its performance are presented aiming at the technological aspect of hardware and software. In addition, and experienced troubles are also presented. (author)

Demand Response Advanced Controls Framework and Assessment of Enabling Technology Costs

Energy Technology Data Exchange (ETDEWEB)

Potter, Jennifer; Cappers, Peter

2017-08-28

The Demand Response Advanced Controls Framework and Assessment of Enabling Technology Costs research describe a variety of DR opportunities and the various bulk power system services they can provide. The bulk power system services are mapped to a generalized taxonomy of DR “service types”, which allows us to discuss DR opportunities and bulk power system services in fewer yet broader categories that share similar technological requirements which mainly drive DR enablement costs. The research presents a framework for the costs to automate DR and provides descriptions of the various elements that drive enablement costs. The report introduces the various DR enabling technologies and end-uses, identifies the various services that each can provide to the grid and provides the cost assessment for each enabling technology. In addition to a report, this research includes a Demand Response Advanced Controls Database and User Manual. They are intended to provide users with the data that underlies this research and instructions for how to use that database more effectively and efficiently.

Recent control and instrumentation systems for BWR nuclear power plant

International Nuclear Information System (INIS)

Fujii, Hiroaki; Higashikawa, Yuichi; Sato, Hideyuki

1990-01-01

For the needs of the more stable operation of nuclear power stations, the upgrading of the measurement and control system for BWRs has been promoted by positively introducing remarkably advancing electronic technology. Further, it is aimed at to construct the synthetic digitized measurement and control system for nuclear power stations to heighten the operation reliability in ABWRs. As the first step of the development in the synthetic digitization, the monitoring and control system for radioactive waste treatment was put in practical use for No.5 plant of Kashiwazaki, Kariwa Nuclear Power Station, Tokyo Electric Power Co., Inc. Hitachi Ltd. has promoted the development and the application to actual plants of the measurement and control system for BWRs, in which digital control technology, optical information transmission technology and the operation-supporting technology using a computer were utilized. Hereafter, it is intended to expand the application of digital measurement and control aiming at improving the reliability, operation performance and maintainability. The nuclear power plant control complex with advanced man-machine interface-90 (NUCAMM-90) was developed, and its application to actual plants is planned. (K.I.)

SPring-8 beamline control system.

Science.gov (United States)

Ohata, T; Konishi, H; Kimura, H; Furukawa, Y; Tamasaku, K; Nakatani, T; Tanabe, T; Matsumoto, N; Ishii, M; Ishikawa, T

1998-05-01

The SPring-8 beamline control system is now taking part in the control of the insertion device (ID), front end, beam transportation channel and all interlock systems of the beamline: it will supply a highly standardized environment of apparatus control for collaborative researchers. In particular, ID operation is very important in a third-generation synchrotron light source facility. It is also very important to consider the security system because the ID is part of the storage ring and is therefore governed by the synchrotron ring control system. The progress of computer networking systems and the technology of security control require the development of a highly flexible control system. An interlock system that is independent of the control system has increased the reliability. For the beamline control system the so-called standard model concept has been adopted. VME-bus (VME) is used as the front-end control system and a UNIX workstation as the operator console. CPU boards of the VME-bus are RISC processor-based board computers operated by a LynxOS-based HP-RT real-time operating system. The workstation and the VME are linked to each other by a network, and form the distributed system. The HP 9000/700 series with HP-UX and the HP 9000/743rt series with HP-RT are used. All the controllable apparatus may be operated from any workstation.

Application of Video Recognition Technology in Landslide Monitoring System

Directory of Open Access Journals (Sweden)

Qingjia Meng

2018-01-01

Full Text Available The video recognition technology is applied to the landslide emergency remote monitoring system. The trajectories of the landslide are identified by this system in this paper. The system of geological disaster monitoring is applied synthetically to realize the analysis of landslide monitoring data and the combination of video recognition technology. Landslide video monitoring system will video image information, time point, network signal strength, power supply through the 4G network transmission to the server. The data is comprehensively analysed though the remote man-machine interface to conduct to achieve the threshold or manual control to determine the front-end video surveillance system. The system is used to identify the target landslide video for intelligent identification. The algorithm is embedded in the intelligent analysis module, and the video frame is identified, detected, analysed, filtered, and morphological treatment. The algorithm based on artificial intelligence and pattern recognition is used to mark the target landslide in the video screen and confirm whether the landslide is normal. The landslide video monitoring system realizes the remote monitoring and control of the mobile side, and provides a quick and easy monitoring technology.

Robust Position Control of Electro-mechanical Systems

OpenAIRE

Rong Mei; Mou Chen

2013-01-01

In this work, the robust position control scheme is proposed for the electro-mechanical system using the disturbance observer and backstepping control method. To the external unknown load of the electro-mechanical system, the nonlinear disturbance observer is given to estimate the external unknown load. Combining the output of the developed nonlinear disturbance observer with backstepping technology, the robust position control scheme is proposed for the electro-mechanical system. The stabili...

Overview of the NSTX Control System

International Nuclear Information System (INIS)

Sichta, P.; Dong, J.; Oliaro, G.; Roney, P.

2001-01-01

The National Spherical Torus Experiment (NSTX) is an innovative magnetic fusion device that was constructed by the Princeton Plasma Physics Laboratory (PPPL) in collaboration with the Oak Ridge National Laboratory, Columbia University, and the University of Washington at Seattle. Since achieving first plasma in 1999, the device has been used for fusion research through an international collaboration of more than twenty institutions. The NSTX is operated through a collection of control systems that encompass a wide range of technology, from hardwired relay controls to real-time control systems with giga-FLOPS of capability. This paper presents a broad introduction to the control systems used on NSTX, with an emphasis on the computing controls, data acquisition, and synchronization systems

The development of control systems for high power steam turbines

International Nuclear Information System (INIS)

Mathey, M.

1983-01-01

The functional and technological aspects of developments in the field of control systems for steam turbines over the last twenty years are analyzed. These developments have now culminated in very sophisticated systems which closely link electronics to high pressure hydraulic technology. A detailed description of these systeme high-lighting the high technical level of the control methods and the flexibility and reliability in service of turbines controlled in this way is given [fr

Nondestructive assay technology and in-plant dynamic materials control: ''DYMAC''

International Nuclear Information System (INIS)

Keppin, G.R.; Maraman, W.J.

1975-01-01

An advanced system of in-plant materials control known as DYMAC, Dynamic Materials Control, is being developed. This major safeguards R and D effort merges state-of-the-art nondestructive assay instrumentation and computer technology, with the clear objective of demonstrating a workable, cost-effective system of stringent, real time control of nuclear materials in a modern plutonium processing facility. Emphasis is placed on developing practical solutions to generic problems of materials measurement and control, so that resulting safeguards techniques and instrumentation will have widespread applicability throughout the nuclear community. (auth)

Control systems under attack?

CERN Document Server

Lüders, Stefan

2005-01-01

The enormous growth of the Internet during the last decade offers new means to share and distribute both information and data. In Industry, this results in a rapprochement of the production facilities, i.e. their Process Control and Automation Systems, and the data warehouses. At CERN, the Internet opens the possibility to monitor and even control (parts of) the LHC and its four experiments remotely from anywhere in the world. However, the adoption of standard IT technologies to Distributed Process Control and Automation Systems exposes inherent vulnerabilities to the world. The Teststand On Control System Security at CERN (TOCSSiC) is dedicated to explore the vulnerabilities of arbitrary Commercial-Of-The-Shelf hardware devices connected to standard Ethernet. As such, TOCSSiC should discover their vulnerabilities, point out areas of lack of security, and address areas of improvement which can then be confidentially communicated to manufacturers. This paper points out risks of accessing the Control and Automa...

Technological options for acid rain control

International Nuclear Information System (INIS)

Princiotta, F.T.; Sedman, C.B.

1993-01-01

The paper discusses technological options for acid rain control. Compliance with Title IV of the Clean Air Act Amendments of 1990 will require careful scrutiny of a number of issues before selecting control options to reduce sulfur dioxide (SO2) and nitrogen oxide (NOx) emissions. One key consideration is the effect of fuel switching or control technology upon the existing dust collector, with additional air toxics legislation looming ahead. A number of likely SO2 and NOx retrofit technologies and estimated costs are presented, along with results of retrofit case studies. New hybrid particulate controls are also being developed to meet future requirements

Research on laser cladding control system based on fuzzy PID

Science.gov (United States)

Zhang, Chuanwei; Yu, Zhengyang

2017-12-01

Laser cladding technology has a high demand for control system, and the domestic laser cladding control system mostly uses the traditional PID control algorithm. Therefore, the laser cladding control system has a lot of room for improvement. This feature is suitable for laser cladding technology, Based on fuzzy PID three closed-loop control system, and compared with the conventional PID; At the same time, the laser cladding experiment and friction and wear experiment were carried out under the premise of ensuring the reasonable control system. Experiments show that compared with the conventional PID algorithm in fuzzy the PID algorithm under the surface of the cladding layer is more smooth, the surface roughness increases, and the wear resistance of the cladding layer is also enhanced.

Improving industrial process control systems security

CERN Document Server

Epting, U; CERN. Geneva. TS Department

2004-01-01

System providers are today creating process control systems based on remote connectivity using internet technology, effectively exposing these systems to the same threats as corporate computers. It is becoming increasingly difficult and costly to patch/maintain the technical infrastructure monitoring and control systems to remove these vulnerabilities. A strategy including risk assessment, security policy issues, service level agreements between the IT department and the controls engineering groups must be defined. In addition an increased awareness of IT security in the controls system engineering domain is needed. As consequence of these new factors the control system architectures have to take into account security requirements, that often have an impact on both operational aspects as well as on the project and maintenance cost. Manufacturers of industrial control system equipment do however also propose progressively security related solutions that can be used for our active projects. The paper discusses ...

Interregional technology transfer on advanced materials and renewable energy systems

International Nuclear Information System (INIS)

Agrianidis, P.; David, C.; Anthymidis, K.; Ekhrawat, M.

2008-01-01

Advanced materials are used in most industrial sectors and human activities and all developing and developed countries as well as international organizations eg. United Nations have established work groups, which survey the national and global state and developments in the area of advanced materials trying to establish strategies on that crucial technology sector. These strategies are focused on research and technology activities including education and vocation training, as well as stimulus for the starting up of new industrial applications. To introduce such a concept in Greece and especially in Northern Greece, the Technological Education Institute of Serres has initiated an Interregional technology transfer project in this scientific field. This project includes mod topics of advanced materials technology with emphasison specific industrial applications (renewable energy systems). The project demonstrates the development of a prototype photovoltaic thermal system in terms of a new industrial product. The product development procedure consists of steps such as initial product design, materials selection and processing, prototype design and manufacturing, quality control, performance optimization, but also control of materials ecocompatibility according to the national trends of life cycle design and recycling techniques. Keywords: Interregional technology transfer, materials, renewable energy systems

Interregional technology transfer on advanced materials and renewable energy systems

Energy Technology Data Exchange (ETDEWEB)

Agrianidis, P.; David, C.; Anthymidis, K.; Ekhrawat, M. [Department of Mechanical Engineering, Technological Educational Institute of Serres, Serres (Greece)

2008-07-01

Advanced materials are used in most industrial sectors and human activities and all developing and developed countries as well as international organizations eg. United Nations have established work groups, which survey the national and global state and developments in the area of advanced materials trying to establish strategies on that crucial technology sector. These strategies are focused on research and technology activities including education and vocation training, as well as stimulus for the starting up of new industrial applications. To introduce such a concept in Greece and especially in Northern Greece, the Technological Education Institute of Serres has initiated an Interregional technology transfer project in this scientific field. This project includes mod topics of advanced materials technology with emphasison specific industrial applications (renewable energy systems). The project demonstrates the development of a prototype photovoltaic thermal system in terms of a new industrial product. The product development procedure consists of steps such as initial product design, materials selection and processing, prototype design and manufacturing, quality control, performance optimization, but also control of materials ecocompatibility according to the national trends of life cycle design and recycling techniques. Keywords: Interregional technology transfer, materials, renewable energy systems.

Definition, technology readiness, and development cost of the orbit transfer vehicle engine integrated control and health monitoring system elements

Science.gov (United States)

Cannon, I.; Balcer, S.; Cochran, M.; Klop, J.; Peterson, S.

1991-01-01

An Integrated Control and Health Monitoring (ICHM) system was conceived for use on a 20 Klb thrust baseline Orbit Transfer Vehicle (OTV) engine. Considered for space used, the ICHM was defined for reusability requirements for an OTV engine service free life of 20 missions, with 100 starts and a total engine operational time of 4 hours. Functions were derived by flowing down requirements from NASA guidelines, previous OTV engine or ICHM documents, and related contracts. The elements of an ICHM were identified and listed, and these elements were described in sufficient detail to allow estimation of their technology readiness levels. These elements were assessed in terms of technology readiness level, and supporting rationale for these assessments presented. The remaining cost for development of a minimal ICHM system to technology readiness level 6 was estimated. The estimates are within an accuracy range of minus/plus 20 percent. The cost estimates cover what is needed to prepare an ICHM system for use on a focussed testbed for an expander cycle engine, excluding support to the actual test firings.

Development of intelligent supervisory control system

International Nuclear Information System (INIS)

Takizawa, Y.; Fukumoto, A.; Makino, M.; Takiguchi, S.

1994-01-01

The objective of the development of an intelligent supervisory control system for next generation plants is enhancement of the operational reliability by applying the recent outcome of artificial intelligence and computer technologies. This system consists of the supervisory control and monitoring for automatic operation, the equipment operation support for historical data management and for test scheduling, the operators' decision making support for accidental plant situations and the human-friendly interface of these support functions. The verification test results showed the validity of the functions realized by this system for the next generation control room. (author)

Learning System Center App Controller

CERN Document Server

Naeem, Nasir

2015-01-01

This book is intended for IT professionals working with Hyper-V, Azure cloud, VMM, and private cloud technologies who are looking for a quick way to get up and running with System Center 2012 R2 App Controller. To get the most out of this book, you should be familiar with Microsoft Hyper-V technology. Knowledge of Virtual Machine Manager is helpful but not mandatory.

VOC emissions control systems

International Nuclear Information System (INIS)

Spessard, J.E.

1993-01-01

The air pollution control equipment marketplace offers many competing technologies for controlling emissions of volatile organic compounds (VOC) in air. If any technology was economically and technically superior under all conditions, it would be the only one on the market. In fact, each technology used to control VOCs is superior under some set of conditions. The reasons for choosing one control technology over another are situation-specific. Some general guidelines to VOC control technologies and the situations where each may be appropriate are presented in this article. The control technologies and applications are summarized in a table

Trends in Energy Management Technology - Part 4: Review ofAdvanced Applications in Energy Management, Control, and InformationSystems

Energy Technology Data Exchange (ETDEWEB)

Yee, Gaymond; Webster, Tom

2003-08-01

In this article, the fourth in a series, we provide a review of advanced applications in Energy Management, Control, and Information Systems (EMCIS). The available features for these products are summarized and analyzed with regard to emerging trends in EMCIS and potential benefits to the Federal sector. The first article [1] covered enabling technologies for emerging energy management systems. The second article [2] serves as a basic reference for building control system (BCS) networking fundamentals and includes an assessment of current approaches to open communications. The third article [3] evaluated several products that exemplify the current state of practice in EMCIS. It is important for energy managers in the Federal sector to have a high level of knowledge and understanding of these complex energy management systems. This series of articles provides energy practitioners with some basic informational and educational tools to help make decisions relative to energy management systems design, specification, procurement, and energy savings potential.

NextGen Technologies on the FAA's Standard Terminal Automation Replacement System

Science.gov (United States)

Witzberger, Kevin; Swenson, Harry; Martin, Lynne; Lin, Melody; Cheng, Jinn-Hwei

2014-01-01

This paper describes the integration, evaluation, and results from a high-fidelity human-in-the-loop (HITL) simulation of key NASA Air Traffic Management Technology Demonstration - 1 (ATD- 1) technologies implemented in an enhanced version of the FAA's Standard Terminal Automation Replacement System (STARS) platform. These ATD-1 technologies include: (1) a NASA enhanced version of the FAA's Time-Based Flow Management, (2) a NASA ground-based automation technology known as controller-managed spacing (CMS), and (3) a NASA advanced avionics airborne technology known as flight-deck interval management (FIM). These ATD-1 technologies have been extensively tested in large-scale HITL simulations using general-purpose workstations to study air transportation technologies. These general purpose workstations perform multiple functions and are collectively referred to as the Multi-Aircraft Control System (MACS). Researchers at NASA Ames Research Center and Raytheon collaborated to augment the STARS platform by including CMS and FIM advisory tools to validate the feasibility of integrating these automation enhancements into the current FAA automation infrastructure. NASA Ames acquired three STARS terminal controller workstations, and then integrated the ATD-1 technologies. HITL simulations were conducted to evaluate the ATD-1 technologies when using the STARS platform. These results were compared with the results obtained when the ATD-1 technologies were tested in the MACS environment. Results collected from the numerical data show acceptably minor differences, and, together with the subjective controller questionnaires showing a trend towards preferring STARS, validate the ATD-1/STARS integration.

Intelligent automated control of robotic systems for environmental restoration

International Nuclear Information System (INIS)

Harrigan, R.W.

1992-01-01

The US Department of Energy's Office of Technology Development (OTD) has sponsored the development of the Generic Intelligent System Controller (GISC) for application to remote system control. Of primary interest to the OTD is the development of technologies which result in faster, safer, and cheaper cleanup of hazardous waste sites than possible using conventional approaches. The objective of the GISC development project is to support these goals by developing a modular robotics control approach which reduces the time and cost of development by allowing reuse of control system software and uses computer models to improve the safety of remote site cleanup while reducing the time and life cycle costs

An IBeacon-Based Location System for Smart Home Control.

Science.gov (United States)

Liu, Qinghe; Yang, Xinshuang; Deng, Lizhen

2018-06-11

Indoor location and intelligent control system can bring convenience to people’s daily life. In this paper, an indoor control system is designed to achieve equipment remote control by using low-energy Bluetooth (BLE) beacon and Internet of Things (IoT) technology. The proposed system consists of five parts: web server, home gateway, smart terminal, smartphone app and BLE beacons. In the web server, fingerprint matching based on RSSI stochastic characteristic and posture recognition model based on geomagnetic sensing are used to establish a more efficient equipment control system, combined with Pedestrian Dead Reckoning (PDR) technology to improve the accuracy of location. A personalized menu of remote “one-click” control is finally offered to users in a smartphone app. This smart home control system has been implemented by hardware, and precision and stability tests have been conducted, which proved the practicability and good user experience of this solution.

Customizing graphical user interface technology for spacecraft control centers

Science.gov (United States)

Beach, Edward; Giancola, Peter; Gibson, Steven; Mahmot, Ronald

1993-01-01

The Transportable Payload Operations Control Center (TPOCC) project is applying the latest in graphical user interface technology to the spacecraft control center environment. This project of the Mission Operations Division's (MOD) Control Center Systems Branch (CCSB) at NASA Goddard Space Flight Center (GSFC) has developed an architecture for control centers which makes use of a distributed processing approach and the latest in Unix workstation technology. The TPOCC project is committed to following industry standards and using commercial off-the-shelf (COTS) hardware and software components wherever possible to reduce development costs and to improve operational support. TPOCC's most successful use of commercial software products and standards has been in the development of its graphical user interface. This paper describes TPOCC's successful use and customization of four separate layers of commercial software products to create a flexible and powerful user interface that is uniquely suited to spacecraft monitoring and control.

Application of improved quality control technology to pressure vessels

International Nuclear Information System (INIS)

Kriedt, F.

1985-01-01

Within the last decade, ASME Boiler and Pressure Vessel Code Section VIII-1 instituted requirements for a formal written quality control system. The results, good and bad, of this requirement are discussed. The effects are far reaching from a national economic standpoint. Quality control technology has improved. These improvements are discussed and compared to existing requirements of the CODE. Recommended improvements are suggested

Procedure guide for the implementation of quality management program in products and services link with the utilization of tracers technology (TT) and Nucleonic Control System

International Nuclear Information System (INIS)

Resnizky, S.; Banados Perez, H.; Longo, G.; Rodriguez Cardona, R.L.; Sebastian Calvo, C.; Kohnenkamp O, I.; Duran P, O.

2000-01-01

This Manual was elaborated in the mark of the project RLA/8/024 ARCAL XLII 'Industrial Applications of the Tracer Technology and Nucleonic Control Systems'. The objective of the present Quality Manual is to spread the Quality Policy and to describe the form of implementing the Quality Management System, according to the requirements of the Standard ISO 9001:2000. It is applied to the design, development, implementation and maintenance of the products of the Organization of Tracers Technology (TT) and Nucleonic Control Systems (SCN). It have 9 Section: I. Introduction, II. Normative references, III. Definitions, IV. Quality Management System; V. Direction Responsibility; VI. Resources Management; VII. Products Accomplishment; VIII. Measurement, Analysis and Improvement and 7 Annex

Advanced Applications of Subsea Control Systems

International Nuclear Information System (INIS)

Duncan, G.; Kitt, P.; Leipner, G.A.; Whitaker, T.

2002-01-01

Technology transfer is one of the main arguments Norwegian companies have for getting involved in difficult markets like Angola. There is great need for sub sea technology in Angola, and Kvaerner Oilfield Products is one of the companies that have successfully fought for contracts in this lucrative market. Field operator TotalFinaElf Exploration and Production Angola has awarded Kvaerner Oilfield Products a USD 3.1 million contract for pre-engineering and qualification testing of the sub sea production systems for the Dalia field offshore Angola. Kvaerner Oilfield Products has already started pre-engineering and testing activity. The sub sea production system includes 42 Xmas trees for controlling the well stream, nine manifolds as well as related control equipment. As sub sea technology improves and advances, equipment that is more complex is being placed on the seabed and downhole environments. Factors such as the cost of the umbilical, increased noise immunity and speed requirements will almost certainly result in optical communications being widely adopted for future system designs. However; in the immediate future operators are likely to insist on backup electrical communications due to the immaturity of certain aspects such as Wetmate optical connectors, fibre handling and fibre degradation. Perhaps the single greatest advantage of open standard sub sea networking is derived from the exploitation of the growing range of third party intelligent instrumentation available on the market. This instrumentation when properly integrated into a sensor to boardroom data management system allows unparalleled control to be delivered to the user at a total cost of installation which can be radically less than conventional technology. It can provide a compelling case for adoption of true open standards. In order to deliver power over any significant distance it is necessary to consider the losses in the transmission medium. The major constraint in the sub sea industry is

Gossamer-1: Mission concept and technology for a controlled deployment of gossamer spacecraft

Science.gov (United States)

Seefeldt, Patric; Spietz, Peter; Sproewitz, Tom; Grundmann, Jan Thimo; Hillebrandt, Martin; Hobbie, Catherin; Ruffer, Michael; Straubel, Marco; Tóth, Norbert; Zander, Martin

2017-01-01

Gossamer structures for innovative space applications, such as solar sails, require technology that allows their controlled and thereby safe deployment. Before employing such technology for a dedicated science mission, it is desirable, if not necessary, to demonstrate its reliability with a Technology Readiness Level (TRL) of six or higher. The aim of the work presented here is to provide reliable technology that enables the controlled deployment and verification of its functionality with various laboratory tests, thereby qualifying the hardware for a first demonstration in low Earth orbit (LEO). The development was made in the Gossamer-1 project of the German Aerospace Center (DLR). This paper provides an overview of the Gossamer-1 mission and hardware development. The system is designed based on the requirements of a technology demonstration mission. The design rests on a crossed boom configuration with triangular sail segments. Employing engineering models, all aspects of the deployment were tested under ambient environment. Several components were also subjected to environmental qualification testing. An innovative stowing and deployment strategy for a controlled deployment, as well as the designs of the bus system, mechanisms and electronics are described. The tests conducted provide insights into the deployment process and allow a mechanical characterization of that deployment process, in particular the measurement of the deployment forces. Deployment on system level could be successfully demonstrated to be robust and controllable. The deployment technology is on TRL four approaching level five, with a qualification model for environmental testing currently being built.

Propose Reactor Control and Monitoring System for RTP

International Nuclear Information System (INIS)

Mohd Sabri Minhat; Izhar Abu Hussin; Mohd Idris Taib; Mohd Khairulezwan Abdul Manan; Nurfarhana Ayuni Joha

2011-01-01

Reactor control and monitoring system is a one of the important features used in reactor. The control and monitoring must come together to provide safety, excellent performance and reliable in nuclear reactor technology application. Objectives of this technical paper are to design and propose reactor control system and reactor monitoring system in Research Reactor (RTP) for Reactor Upgrading Project. (author)

The development of control technologies applied to waste processing operations

International Nuclear Information System (INIS)

Grasz, E.; Baker, S.; Couture, S.; Dennison, D.; Holliday, M.; Hurd, R.; Kettering, B.; Merrill, R.; Wilhelmson, K.

1993-02-01

Typical waste and residue processes involve some level of human interaction. The risk of exposure to unknown hazardous materials and the potential for radiation contamination provide the impetus for physically separating or removing operators from such processing steps. Technologies that facilitate separation of the operator from potential contamination include glove box robotics; modular systems for remote and automated servicing; and interactive controls that minimize human intervention. Lawrence Livermore National Laboratory (LLNL) is developing an automated system which by design will supplant the operator for glove box tasks, thus affording protection from the risk of radiation exposure and minimizing operator associated waste.This paper describes recent accomplishments in technology development and integration, and outlines the future goals at LLNL for achieving this integrated, interactive control capability

Controlling air pollution from passenger ferries: cost-effectiveness of seven technological options.

Science.gov (United States)

Farrell, Alexander E; Corbett, James J; Winebrake, James J

2002-12-01

Continued interest in improving air quality in the United States along with renewed interest in the expansion of urban passenger ferry service has created concern about air pollution from ferry vessels. This paper presents a methodology for estimating the air pollution emissions from passenger ferries and the costs of emissions control strategies. The methodology is used to estimate the emissions and costs of retrofitting or re-powering ferries with seven technological options (combinations of propulsion and emission control systems) onto three vessels currently in service in San Francisco Bay. The technologies include improved engine design, cleaner fuels (including natural gas), and exhaust gas cleanup devices. The three vessels span a range of ages and technologies, from a 25-year-old monohull to a modern, high-speed catamaran built only four years ago. By looking at a range of technologies, vessel designs, and service conditions, a sense of the broader implications of controlling emissions from passenger ferries across a range of vessels and service profiles is provided. Tier 2-certified engines are the most cost-effective choice, but all options are cost-effective relative to other emission control strategies already in place in the transportation system.

Environmental control technology activities of the Department of Energy in FY 1977

International Nuclear Information System (INIS)

1977-11-01

The Department of Energy is responsible for the research, development, and demonstration of emerging energy technologies and the promotion of energy conservation. An integral and significant part of that responsibility includes the balancing of energy goals with environmental requirements to protect and enhance the general health, safety, and welfare of the nation. This requires that environmental effects be considered and mitigating measures be taken in all energy processes through incorporation of environmental and safety controls which are developed as an integral part of energy system design. This inventory of environmental control technology activities was initiated by the Administrator, ERDA, prior to the incorporation of that administration within the Department of Energy. This compilation of total Energy Research and Development Administration (ERDA) environmental control technology activities, and associated funding, related to environmental control technology identifies the resources committed by ERDA to demonstrate its objective to protect and enhance the general health, safety, and welfare of the nation in the research, development, and demonstration of energy systems. Only ERDA research, development, and demonstration activities are covered in this report. The compilation for FY 1978 will encompass all of the DOE activities

Space Station Environmental Control/Life Support System engineering

Science.gov (United States)

Miller, C. W.; Heppner, D. B.

1985-01-01

The present paper is concerned with a systems engineering study which has provided an understanding of the overall Space Station ECLSS (Environmental Control and Life Support System). ECLSS/functional partitioning is considered along with function criticality, technology alternatives, a technology description, single thread systems, Space Station architectures, ECLSS distribution, mechanical schematics per space station, and Space Station ECLSS characteristics. Attention is given to trade studies and system synergism. The Space Station functional description had been defined by NASA. The ECLSS will utilize technologies which embody regenerative concepts to minimize the use of expendables.

Feasibility of EGS Well Control Systems

Energy Technology Data Exchange (ETDEWEB)

Norann, Randy A [Perma Works LLC; Darlow, Richard [GeoTek Energy LLC

2015-02-03

This report covers the 8th major objective listed in Grant DE-FG36-08GO18185. This objective takes the information and experience gained from the development of 300°C well monitoring system and applies them to concepts envisioned for future geothermal well control systems supporting EGS power production. This report covers a large number of instrumentation and control system engineering issues for EGS wells while also providing a window into existing technology to address those issues.

Automatic process control in anaerobic digestion technology: A critical review.

Science.gov (United States)

Nguyen, Duc; Gadhamshetty, Venkataramana; Nitayavardhana, Saoharit; Khanal, Samir Kumar

2015-10-01

Anaerobic digestion (AD) is a mature technology that relies upon a synergistic effort of a diverse group of microbial communities for metabolizing diverse organic substrates. However, AD is highly sensitive to process disturbances, and thus it is advantageous to use online monitoring and process control techniques to efficiently operate AD process. A range of electrochemical, chromatographic and spectroscopic devices can be deployed for on-line monitoring and control of the AD process. While complexity of the control strategy ranges from a feedback control to advanced control systems, there are some debates on implementation of advanced instrumentations or advanced control strategies. Centralized AD plants could be the answer for the applications of progressive automatic control field. This article provides a critical overview of the available automatic control technologies that can be implemented in AD processes at different scales. Copyright © 2015 Elsevier Ltd. All rights reserved.

Technology for sodium purity control

Energy Technology Data Exchange (ETDEWEB)

Jeong, Ji Young; Kim, B. H.; Kim, T. J. [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-10-01

When sodium is used as heat transfer fluid, the plugging in coolant flow, the corrosion of structure material and the transfer of radioactive material caused by the impurities in sodium are worth considerable. Accordingly, these impurities must be monitored and controlled continuously by sodium purification devices in the heat transfer system which sodium is used as coolant. Sodium purification loop was constructed for the purpose of accumulating the technology for purity control of the coolant, developing and verifying further efficient instruments for sodium purification. The plugging meter and the cold trap is used as the implement for measuring and controlling the oxygen and the hydrogen, the main impurities in sodium coolant. They are capable of excellent performance as the implements which could detect and monitor the impurities to the concentration limit required for nuclear reactor. Sodium purification loop could be used variably according to the experimental purpose. 18 refs., 34 figs., 8 tabs. (Author)

Advanced digital computers, controls, and automation technologies for power plants: Proceedings

International Nuclear Information System (INIS)

Bhatt, S.C.

1992-08-01

This document is a compilation of the papers that were presented at an EPRI workshop on Advances in Computers, Controls, and Automation Technologies for Power Plants. The workshop, sponsored by EPRI's Nuclear Power Division, took place February 1992. It was attended by 157 representatives from electric utilities, equipment manufacturers, engineering consulting organizations, universities, national laboratories, government agencies and international utilities. More than 40% of the attendees were from utilities representing the majority group. There were 30% attendees from equipment manufacturers and the engineering consulting organizations. The participants from government agencies, universities, and national laboratories were about 10% each. The workshop included a keynote address, 35 technical papers, and vendor's equipment demonstrations. The technical papers described the state-of-the-art in the areas of recent utility digital upgrades such as digital feedwater controllers, steam generator level controllers, integrated plant computer systems, computer aided diagnostics, automated testing and surveillance and other applications. A group of technical papers presented the ongoing B ampersand W PWR integrated plant control system prototype developments with the triple redundant advanced digital control system. Several international papers from France, Japan and U.K. presented their programs on advance power plant design and applications. Significant advances in the control and automation technologies such as adaptive controls, self-tuning methods, neural networks and expert systems were presented by developers, universities, and national laboratories. Individual papers are indexed separately

Sensor Technologies for Intelligent Transportation Systems.

Science.gov (United States)

Guerrero-Ibáñez, Juan; Zeadally, Sherali; Contreras-Castillo, Juan

2018-04-16

Modern society faces serious problems with transportation systems, including but not limited to traffic congestion, safety, and pollution. Information communication technologies have gained increasing attention and importance in modern transportation systems. Automotive manufacturers are developing in-vehicle sensors and their applications in different areas including safety, traffic management, and infotainment. Government institutions are implementing roadside infrastructures such as cameras and sensors to collect data about environmental and traffic conditions. By seamlessly integrating vehicles and sensing devices, their sensing and communication capabilities can be leveraged to achieve smart and intelligent transportation systems. We discuss how sensor technology can be integrated with the transportation infrastructure to achieve a sustainable Intelligent Transportation System (ITS) and how safety, traffic control and infotainment applications can benefit from multiple sensors deployed in different elements of an ITS. Finally, we discuss some of the challenges that need to be addressed to enable a fully operational and cooperative ITS environment.

Sensor Technologies for Intelligent Transportation Systems

Science.gov (United States)

Guerrero-Ibáñez, Juan; Zeadally, Sherali

2018-01-01

Modern society faces serious problems with transportation systems, including but not limited to traffic congestion, safety, and pollution. Information communication technologies have gained increasing attention and importance in modern transportation systems. Automotive manufacturers are developing in-vehicle sensors and their applications in different areas including safety, traffic management, and infotainment. Government institutions are implementing roadside infrastructures such as cameras and sensors to collect data about environmental and traffic conditions. By seamlessly integrating vehicles and sensing devices, their sensing and communication capabilities can be leveraged to achieve smart and intelligent transportation systems. We discuss how sensor technology can be integrated with the transportation infrastructure to achieve a sustainable Intelligent Transportation System (ITS) and how safety, traffic control and infotainment applications can benefit from multiple sensors deployed in different elements of an ITS. Finally, we discuss some of the challenges that need to be addressed to enable a fully operational and cooperative ITS environment. PMID:29659524

Sensor Technologies for Intelligent Transportation Systems

Directory of Open Access Journals (Sweden)

Juan Guerrero-Ibáñez

2018-04-01

Full Text Available Modern society faces serious problems with transportation systems, including but not limited to traffic congestion, safety, and pollution. Information communication technologies have gained increasing attention and importance in modern transportation systems. Automotive manufacturers are developing in-vehicle sensors and their applications in different areas including safety, traffic management, and infotainment. Government institutions are implementing roadside infrastructures such as cameras and sensors to collect data about environmental and traffic conditions. By seamlessly integrating vehicles and sensing devices, their sensing and communication capabilities can be leveraged to achieve smart and intelligent transportation systems. We discuss how sensor technology can be integrated with the transportation infrastructure to achieve a sustainable Intelligent Transportation System (ITS and how safety, traffic control and infotainment applications can benefit from multiple sensors deployed in different elements of an ITS. Finally, we discuss some of the challenges that need to be addressed to enable a fully operational and cooperative ITS environment.

ESTABLISHMENT OF AN ENVIRONMENTAL CONTROL TECHNOLOGY LABORATORY WITH A CIRCULATING FLUIDIZED-BED COMBUSTION SYSTEM

Energy Technology Data Exchange (ETDEWEB)

Wei-Ping Pan; Andy Wu; John T. Riley

2004-10-30

This report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period July 1, 2004 through September 30, 2004. The following tasks have been completed. First, renovation of the new Combustion Laboratory and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building have started. Second, the design if the component parts of the CFBC system have been reviewed and finalized so that the drawings may be released to the manufacturers during the next quarter. Third, the experiments for solid waste (chicken litter) incineration have been conducted using a Thermogravimetric Analyzer (TGA). This is in preparation for testing in the simulated fluidized-bed combustor. The experimental results from this study are presented in this report. Finally, the proposed work for the next quarter has been outlined in this report.

Investigation on food sanitation controlling technologies; Shokuhin eisei kanri gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

Doi, Y [Hokkaido Electric Power Co. Inc., Sapporo (Japan); Nishioka, J

2000-03-24

Investigation has been made on the current status of food sanitation controlling technologies. Eighty percent of food poisoning is caused by bacte such as Salmonera, enteritis vibrio, staphylococcus, and pathogenic colibacillus. Putrefaction as the cause for food poisoning occurs from proliferation of different microorganisms. Heating sterilization is the main method being performed, but non-heating method may include sterilization by flash and high voltage pulse discharge in addition to ultra-high pressure and ultraviolet ray sterilization. As a result of the questionnaire survey, what is extracted as the problems in the food sanitation controlling technologies is to establish a rinsing and sterilizing method with large sterilization effect, an effective sterilizing method and thawing of processed marine products, and a cooling method in food processing. Increasingly demanded for the future is to develop a foodstuff sanitation control system using as the core the hazard analysis critical control point (HACCP, a quality control program developed by the U.S. NASA to ensure safety in manufacturing space food), and micro-organism control and sterilizing technologies to support the above system. The flash pulse and high-voltage pulse sterilizing technologies as the non-heating sterilizing technology are more effective than the conventional heating sterilization methods also from the aspect of quality retention after sterilization. More active development thereof is desired. (NEDO)

FY 1994 report on the results of the development of a large wind power system. Development of control technology of the array type wind power system; 1994 nendo ogata furyoku hatsuden system kaihatsu seika hokokusho. Shugogata furyoku hatsuden system no seigyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This technology development aims at developing the design technology of the array type wind power system and the control technology to efficiently operate the system. As a result, the wind turbine produced by Micon was selected. The rated power is 100kW, and the number of the wind turbine is three. The three-phase short-circuit capacity at the generating end of the wind power generation facilities is 26,25 MVA, which can fully be broken. A simulation of voltage variation/frequency variation was made to grasp various phenomena of the output of the wind power system influencing the power source system and power distribution system. As a result, it was confirmed that it is possible to operate the system safely without lowering the quality of power. As to the overall monitor/control system which controls wind turbines, five wind turbines as many as possible are grid-interconnected and the number of wind turbine is to be controlled by a ratio of the total demand power to the gross generating output of wind power in the Miyako system, for the purpose of increasing the rate of equipment utilization of the wind power system also at the time of the lowest load of the Miyako system. In the operation of two-system interconnection, the gross power generating amount was 1,321,250 kWh, which increased 9.7% over the results in FY 1993. (NEDO)

Effect of automatic control technologies on emission reduction in small-scale combustion

Energy Technology Data Exchange (ETDEWEB)

Ruusunen, M. [Control Engineering Laboratory, University of Oulu (Finland)

2007-07-01

Automatic control can be regarded as a primary measure for preventing combustion emissions. In this view, the control technology covers broadly the control methods, sensors and actuators for monitoring and controlling combustion. In addition to direct control of combustion process, it can also give tools for condition monitoring and optimisation of total heat consumption by system integration thus reducing the need for excess conversion of energy. Automatic control has already shown its potential in small-scale combustion. The potential, but still unrealised advantages of automatic control in this scale are the adaptation to changes in combustion conditions (fuel, environment, device, user) and the continuous optimisation of the air/fuel ratio. Modem control technology also covers combustion condition monitoring, diagnostics, and the higher level optimisation of the energy consumption with system integration. In theory, these primary measures maximise the overall efficiency, enabling a significant reduction in fuel consumption and thus total emissions per small-scale combustion unit, specifically at the annual level.

Emission Control Technologies for Thermal Power Plants

Science.gov (United States)

Nihalani, S. A.; Mishra, Y.; Juremalani, J.

2018-03-01

Coal thermal power plants are one of the primary sources of artificial air emissions, particularly in a country like India. Ministry of Environment and Forests has proposed draft regulation for emission standards in coal-fired power plants. This includes significant reduction in sulphur-dioxide, oxides of nitrogen, particulate matter and mercury emissions. The first step is to evaluate the technologies which represent the best selection for each power plant based on its configuration, fuel properties, performance requirements, and other site-specific factors. This paper will describe various technology options including: Flue Gas Desulfurization System, Spray Dryer Absorber (SDA), Circulating Dry Scrubber (CDS), Limestone-based Wet FGD, Low NOX burners, Selective Non Catalytic Reduction, Electrostatic Precipitator, Bag House Dust Collector, all of which have been evaluated and installed extensively to reduce SO2, NOx, PM and other emissions. Each control technology has its advantages and disadvantages. For each of the technologies considered, major features, potential operating and maintenance cost impacts, as well as key factors that contribute to the selection of one technology over another are discussed here.

Development of fluid and I and C systems design technology

Energy Technology Data Exchange (ETDEWEB)

Sim, Yoon Sub; Park, C. K.; Kim, S. O. [and others

2000-05-01

LMR is the reactor type that makes utilization of uranium resource very efficiently and the necessity of construction of a LMR in 2020's has been raised. However, the design technology required for construction has not been secured domestically. To fulfill the necessity, study has been made for the LMR system design technology and conceptual design of KALIMER systems for fluid, instrumentation, control, and protection have been developed. Also the computer code systems for the design and analysis of the KALIMER fluid systems have been developed. These study results are to used as the starting point of the next phase LMR design technology development research.

Development of fluid and I and C systems design technology

International Nuclear Information System (INIS)

Sim, Yoon Sub; Park, C. K.; Kim, S. O.

2000-05-01

LMR is the reactor type that makes utilization of uranium resource very efficiently and the necessity of construction of a LMR in 2020's has been raised. However, the design technology required for construction has not been secured domestically. To fulfill the necessity, study has been made for the LMR system design technology and conceptual design of KALIMER systems for fluid, instrumentation, control, and protection have been developed. Also the computer code systems for the design and analysis of the KALIMER fluid systems have been developed. These study results are to used as the starting point of the next phase LMR design technology development research

Development of fluid and I and C systems design technology

Energy Technology Data Exchange (ETDEWEB)

Sim, Yoon Sub; Park, C K; Kim, S O [and others

2000-05-01

LMR is the reactor type that makes utilization of uranium resource very efficiently and the necessity of construction of a LMR in 2020's has been raised. However, the design technology required for construction has not been secured domestically. To fulfill the necessity, study has been made for the LMR system design technology and conceptual design of KALIMER systems for fluid, instrumentation, control, and protection have been developed. Also the computer code systems for the design and analysis of the KALIMER fluid systems have been developed. These study results are to used as the starting point of the next phase LMR design technology development research.

Implementing UPDM to develop command and control systems

CSIR Research Space (South Africa)

Oosthuizen, R

2016-09-01

Full Text Available Systems engineering is an established approach to develop systems, including complex sociotechnical systems such as Command and Control (C2) Systems. These systems often occur through introduction of a new technology into an existing system...

Nova laser alignment control system

International Nuclear Information System (INIS)

Van Arsdall, P.J.; Holloway, F.W.; McGuigan, D.L.; Shelton, R.T.

1984-01-01

Alignment of the Nova laser requires control of hundreds of optical components in the ten beam paths. Extensive application of computer technology makes daily alignment practical. The control system is designed in a manner which provides both centralized and local manual operator controls integrated with automatic closed loop alignment. Menudriven operator consoles using high resolution color graphics displays overlaid with transport touch panels allow laser personnel to interact efficiently with the computer system. Automatic alignment is accomplished by using image analysis techniques to determine beam references points from video images acquired along the laser chain. A major goal of the design is to contribute substantially to rapid experimental turnaround and consistent alignment results. This paper describes the computer-based control structure and the software methods developed for aligning this large laser system

Dynamitron control systems

International Nuclear Information System (INIS)

Lisanti, Thomas F.

2005-01-01

The Dynamitron control system utilizes the latest personal computer technology in control circuitry and components. Both the DPC-2000 and newer Millennium series of control systems make use of their modular architecture in both software and hardware to keep up with customer and engineering demands. This also allows the main structure of the software to remain constant for the user while software drivers are easily changed as hardware demands are modified and improved. The system is presented as four units; the Remote I/O (Input/Output), Local Analog and Digital I/O, Operator Interface and the Main Computer. The operator is provided with a selection of many informative screen displays. The control program handles all graphic screen displays and the updating of these screens directly; it does not communicate to a display terminal. This adds to the quick response and excellent operator feedback received while operating the accelerator. The CPU also has the ability to store and record all process variable setpoints for each product that will be treated. All process parameters are printed to a report at regular intervals during a process run for record keeping

Chaos in electric drive systems analysis control and application

CERN Document Server

Chau, K T

2011-01-01

In Chaos in Electric Drive Systems: Analysis, Control and Application authors Chau and Wang systematically introduce an emerging technology of electrical engineering that bridges abstract chaos theory and practical electric drives. The authors consolidate all important information in this interdisciplinary technology, including the fundamental concepts, mathematical modeling, theoretical analysis, computer simulation, and hardware implementation. The book provides comprehensive coverage of chaos in electric drive systems with three main parts: analysis, control and application. Corresponding drive systems range from the simplest to the latest types: DC, induction, synchronous reluctance, switched reluctance, and permanent magnet brushless drives.The first book to comprehensively treat chaos in electric drive systemsReviews chaos in various electrical engineering technologies and drive systemsPresents innovative approaches to stabilize and stimulate chaos in typical drivesDiscusses practical application of cha...

Cognitive Technologies: The Design of Joint Human-Machine Cognitive Systems

OpenAIRE

Woods, David D.

1985-01-01

This article explores the implications of one type of cognitive technology, techniques and concepts to develop joint human-machine cognitive systems, for the application of computational technology by examining the joint cognitive system implicit in a hypothetical computer consultant that outputs some form of problem solution. This analysis reveals some of the problems can occur in cognitive system design-e.g., machine control of the interaction, the danger of a responsibility-authority doubl...

International Conference on Intelligent Technologies and Engineering System (ICITES 2012)

CERN Document Server

Huang, Yi-Cheng; Intelligent Technologies and Engineering Systems

2013-01-01

This book concentrates on intelligent technologies as it relates to engineering systems. The book covers the following topics: networking, signal processing, artificial intelligence, control and software engineering, intelligent electronic circuits and systems, communications, and materials and mechanical engineering. The book is a collection of original papers that have been reviewed by technical editors. These papers were presented at the International Conference on Intelligent Technologies and Engineering Systems, held Dec. 13-15, 2012.

Division of Cyber Safety and Security Responsibilities Between Control System Owners and Suppliers

OpenAIRE

Skotnes , Ruth

2016-01-01

Part 2: CONTROL SYSTEMS SECURITY; International audience; The chapter discusses the important issue of responsibility for information and communications technology (ICT) – or cyber – safety and security for industrial control systems and the challenges involved in dividing the responsibility between industrial control system owners and suppliers in the Norwegian electric power supply industry. Industrial control system owners are increasingly adopting information and communications technologi...

Preferences for technology versus human assistance and control over technology in the performance of kitchen and personal care tasks in baby boomers and older adults.

Science.gov (United States)

Beach, Scott R; Schulz, Richard; Matthews, Judith T; Courtney, Karen; Dabbs, Annette DeVito

2014-11-01

Quality of Life technology (QoLT) stresses humans and technology as mutually dependent and aware, working together to improve task performance and quality of life. This study examines preferences for technology versus human assistance and control in the context of QoLT. Data are from a nationally representative, cross-sectional web-based sample of 416 US baby boomers (45-64) and 114 older adults (65+) on preferences for technology versus human assistance and control in the performance of kitchen and personal care tasks. Multinomial logistic regression and ordinary least squares regression were used to determine predictors of these preferences. Respondents were generally accepting of technology assistance but wanted to maintain control over its' operation. Baby boomers were more likely to prefer technology than older adults, and those with fewer QoLT privacy concerns and who thought they were more likely to need future help were more likely to prefer technology over human assistance and more willing to relinquish control to technology. Results suggest the need for design of person- and context-aware QoLT systems that are responsive to user desires for level of control over operation of the technology. The predictors of these preferences suggest potentially receptive markets for the targeting of QoLT systems.

Environmental control implications of generating electric power from coal. Technology status report. Volume II

Energy Technology Data Exchange (ETDEWEB)

None

1976-12-01

This is the first in a series of reports evaluating environmental control technologies applicable to the coal-to-electricity process. The technologies are described and evaluated from an engineering and cost perspective based upon the best available information obtained from utility experience and development work in progress. Environmental control regulations and the health effects of pollutants are also reviewed. Emphasis is placed primarily upon technologies that are now in use. For SO/sub 2/ control, these include the use of low sulfur coal, cleaned coal, or flue-gas desulfurization systems. Electrostatic precipitators and fabric filters used for the control of particulate matter are analyzed, and combustion modifications for NO/sub x/ control are described. In each area, advanced technologies still in the development stage are described briefly and evaluated on the basis of current knowledge. Fluidized-bed combustion (FBC) is a near-term technology that is discussed extensively in the report. The potential for control of SO/sub 2/ and NO/sub x/ emissions by use of FBC is analyzed, as are the resulting solid waste disposal problems, cost estimates, and its potential applicability to electric utility systems. Volume II presents the detailed technology analyses complete with reference citations. This same material is given in condensed form in Volume I without references. A brief executive summary is also given in Volume I.

Proceedings of the Technology Roadmap Workshop on Communication and Control Systems for Distributed Energy Implementation and Testing

Energy Technology Data Exchange (ETDEWEB)

none,

2002-05-01

More than 50 experts from energy and information technology industries, Federal and State government agencies, universities, and National Laboratories participated in the “Communication and Control Systems for Distributed Energy Implementation and Testing Workshop” in Reston, Virginia, on May 14-15, 2002. This was a unique workshop in that, for the first time, representatives from the information technology sector and those from energy-related industries, Federal and State government agencies, universities, and National Laboratories, gathered to discuss these issues and develop a set of action-oriented implementation strategies. A planning committee of industry, consultant, and government representatives laid the groundwork for the workshop by identifying key participants and developing an appropriate agenda. This document reflects the ideas and priorities discussed by workshop participants.

Environment, safety, and health information technology systems integration.

Energy Technology Data Exchange (ETDEWEB)

Hendrickson, David A.; Bayer, Gregory W.

2006-02-01

The ES&H Information Systems department, motivated by the numerous isolated information technology systems under its control, undertook a significant integration effort. This effort was planned and executed over the course of several years and parts of it still continue today. The effect was to help move the ES&H Information Systems department toward integration with the corporate Information Solutions and Services center.

Universal CNC platform motion control technology for industrial CT

International Nuclear Information System (INIS)

Cheng Senlin; Wang Yang

2011-01-01

According to the more scanning methods and the higher speed of industrial CT, the higher precision of the motion location and the data collection sync-control is required at present, a new motion control technology was proposed, which was established based on the universal CNC system with high precision of multi-axis control. Aiming at the second and the third generation of CT scanning motion, a control method was researched, and achieved the demands of the changeable parameters and network control, Through the simulation of the second and the third generation of CT scanning motion process, the control precision of the rotation axis reached 0.001° and the linear axis reached 0.002 mm, Practical tests showed this system can meet the requirements of the multi-axis motion integration and the sync signal control, it also have advantages in the control precision and the performance. (authors)

Technology Transfer Programme In Reactor Digital Instrumentation And Control System (REDICS) Project: Knowledge, Experiences And Future Expectations

International Nuclear Information System (INIS)

Nurfarhana Ayuni Joha; Mohamad Puad Abu; Izhar Abu Hussin; Ridzuan Abdul Mutalib; Zareen Khan Abdul Jalil Khan; Mohd Khairulezwan Abdul Manan; Mohd Sabri Minhat; Mohd Idris Taib

2013-01-01

The PUSPATI TRIGA MARK II research reactor in Malaysia was commissioned in 1982. After 31 years of operation, Nuclear Malaysia is taking an approach for a better research and development in nuclear radiations as well as the technical services that provided. Reactor TRIGA PUSPATI (RTP) is currently upgrading its control console from analogue to digital system. The Reactor Digital Instrumentation and Control System (ReDICS) project is done on cooperation with Korea Atomic Energy Research Institute (KAERI), Korea including the technical part from the design stage until commissioning as well as the Technology Transfer Program (TTP). TTP in this ReDICS project is a part of Human Resource and System Development Program. It was carried out from the design stage until the commissioning of the system. It covers all subjects related to the design on the digital system and the requirements for the operation of RTP. The objective of this paper is to share the knowledge and experiences gained through this ReDICS project. This paper will also discuss the future expectations from this ReDICS project for Nuclear Malaysia and its personnel, as well as to the country. (author)

JV Task 126 - Mercury Control Technologies for Electric Utilities Burning Bituminous Coal

Energy Technology Data Exchange (ETDEWEB)

Jason Laumb; John Kay; Michael Jones; Brandon Pavlish; Nicholas Lentz; Donald McCollor; Kevin Galbreath

2009-03-29

The EERC developed an applied research consortium project to test cost-effective mercury (Hg) control technologies for utilities burning bituminous coals. The project goal was to test innovative Hg control technologies that have the potential to reduce Hg emissions from bituminous coal-fired power plants by {ge}90% at costs of one-half to three-quarters of current estimates for activated carbon injection (ACI). Hg control technology evaluations were performed using the EERC's combustion test facility (CTF). The CTF was fired on pulverized bituminous coals at 550,000 Btu/hr (580 MJ/hr). The CTF was configured with the following air pollution control devices (APCDs): selective catalytic reduction (SCR) unit, electrostatic precipitator (ESP), and wet flue gas desulfurization system (WFDS). The Hg control technologies investigated as part of this project included ACI (three Norit Americas, Inc., and eleven Envergex sorbents), elemental mercury (Hg{sup 0}) oxidation catalysts (i.e., the noble metals in Hitachi Zosen, Cormetech, and Hitachi SCR catalysts), sorbent enhancement additives (SEAs) (a proprietary EERC additive, trona, and limestone), and blending with a Powder River Basin (PRB) subbituminous coal. These Hg control technologies were evaluated separately, and many were also tested in combination.

Control architecture of power systems: Modeling of purpose and function

DEFF Research Database (Denmark)

Heussen, Kai; Saleem, Arshad; Lind, Morten

2009-01-01

Many new technologies with novel control capabilities have been developed in the context of “smart grid” research. However, often it is not clear how these capabilities should best be integrated in the overall system operation. New operation paradigms change the traditional control architecture...... of power systems and it is necessary to identify requirements and functions. How does new control architecture fit with the old architecture? How can power system functions be specified independent of technology? What is the purpose of control in power systems? In this paper, a method suitable...... for semantically consistent modeling of control architecture is presented. The method, called Multilevel Flow Modeling (MFM), is applied to the case of system balancing. It was found that MFM is capable of capturing implicit control knowledge, which is otherwise difficult to formalize. The method has possible...

Technology of solving multi-objective problems of control of systems with distributed parameters

Science.gov (United States)

Rapoport, E. Ya.; Pleshivtseva, Yu. E.

2017-07-01

A constructive technology of multi-objective optimization of control of distributed parameter plants is proposed. The technology is based on a single-criterion version in the form of the minimax convolution of normalized performance criteria. The approach under development is based on the transition to an equivalent form of the variational problem with constraints, with the problem solution being a priori Pareto-effective. Further procedures of preliminary parameterization of control actions and subsequent reduction to a special problem of semi-infinite programming make it possible to find the sought extremals with the use of their Chebyshev properties and fundamental laws of the subject domain. An example of multi-objective optimization of operation modes of an engineering thermophysics object is presented, which is of independent interest.

The LANSCE RICE control system upgrade.

Energy Technology Data Exchange (ETDEWEB)

Oothoudt, Michael; Schaller, S. (Stuart); Bjorklund, E. A. (Eric A.); Burns, M. J. (Mary J.); Carr, G. (Gary); Carr, G. (Gary); Faucett, John Allen,; Hayden, D. J. (David J.); Lusk, M. D. (Matthew D.); Merl, R. B. (Robert B.); Potter, J. M. (Jerry M.); Reynolds, J. A. (Jerome A.); Romero, D. B. (Dolores B.); Shelley, F. E. (Fred E.)

2003-01-01

The LANSCE (Los Alamos Neutron Science Center) control system upgrade program continues with the impending replacement of the RICE (Remote Instrumentation and Control Equipment) subsystem. The RICE subsystem upgrade is a challenge because of its technology (late 1960s), number of channels (>10,000), and unique characteristics (all-modules data takes, timed/flavored data takes). The plan is to replace at least the non-timed data and the command portions of the subsystem with Programmable Logic Controllers (PLCs). We discuss motivations, technological challenges, proof-of-principle, and planning. The boundary condition, as usual, is that we must implement these major changes on a running accelerator.

The LANSCE RICE control system upgrade

International Nuclear Information System (INIS)

Oothoudt, Michael; Schaller, S.; Bjorklund, E.A.; Burns, M.J.; Carr, G.; Faucett, John Allen; Hayden, D.J.; Lusk, M.D.; Merl, R.B.; Potter, J.M.; Reynolds, J.A.; Romero, D.B.; Shelley, F.E.

2003-01-01

The LANSCE (Los Alamos Neutron Science Center) control system upgrade program continues with the impending replacement of the RICE (Remote Instrumentation and Control Equipment) subsystem. The RICE subsystem upgrade is a challenge because of its technology (late 1960s), number of channels (>10,000), and unique characteristics (all-modules data takes, timed/flavored data takes). The plan is to replace at least the non-timed data and the command portions of the subsystem with Programmable Logic Controllers (PLCs). We discuss motivations, technological challenges, proof-of-principle, and planning. The boundary condition, as usual, is that we must implement these major changes on a running accelerator.

Investigational report on the trend of control technology; Seigyo gijutsu doko chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-06-01

For the purpose of corresponding to changes of the industrial structure and making full use of the control technology, the paper investigated the state of the application. High-grade automation in the manufacturing industry has reached the spread of use at big companies for these 10 years. The hierarchical structure of business/process/DCS has been completed, and the optimal control and the advanced control have been realized. The development and spread to the much wider field is anticipated. The soft structure system is needed for equipment improvement in view of the life cycle of equipment and toward the elimination of bottlenecking. For the design of the control system, commercial tools began to be much used, and it is expected in future to accumulate and recycle the knowledge/knowhow for effective design work. Further, strict simulation models based material balance and heat balance have also been on the rise, and the advance in technology is expected. Because of the total productivity of the production equipment, the control technology is anticipated not only for the pursuit of controllability but for the use as supporting technology in the operation/driving/failure diagnosis for working out, carrying out and evaluating the optimum operation plan. 18 refs., 99 figs., 100 tabs.

Survey of LWR environmental control technology performance and cost

International Nuclear Information System (INIS)

Heeb, C.M.; Aaberg, R.L.; Cole, B.M.; Engel, R.L.; Kennedy, W.E. Jr.; Lewallen, M.A.

1980-03-01

This study attempts to establish a ranking for species that are routinely released to the environment for a projected nuclear power growth scenario. Unlike comparisons made to existing standards, which are subject to frequent revision, the ranking of releases can be used to form a more logical basis for identifying the areas where further development of control technology could be required. This report describes projections of releases for several fuel cycle scenarios, identifies areas where alternative control technologies may be implemented, and discusses the available alternative control technologies. The release factors were used in a computer code system called ENFORM, which calculates the annual release of any species from any part of the LWR nuclear fuel cycle given a projection of installed nuclear generation capacity. This survey of fuel cycle releases was performed for three reprocessing scenarios (stowaway, reprocessing without recycle of Pu and reprocessing with full recycle of U and Pu) for a 100-year period beginning in 1977. The radioactivity releases were ranked on the basis of a relative ranking factor. The relative ranking factor is based on the 100-year summation of the 50-year population dose commitment from an annual release of radioactive effluents. The nonradioactive releases were ranked on the basis of dilution factor. The twenty highest ranking radioactive releases were identified and each of these was analyzed in terms of the basis for calculating the release and a description of the currently employed control method. Alternative control technology is then discussed, along with the available capital and operating cost figures for alternative control methods

Development of 6-DOF painting robot control system

Science.gov (United States)

Huang, Junbiao; Liu, Jianqun; Gao, Weiqiang

2017-01-01

With the development of society, the spraying technology of manufacturing industry in China has changed from the manual operation to the 6-DOF (Degree Of Freedom)robot automatic spraying. Spraying painting robot can not only complete the work which does harm to human being, but also improve the production efficiency and save labor costs. Control system is the most critical part of the 6-DOF robots, however, there is still a lack of relevant technology research in China. It is very necessary to study a kind of control system of 6-DOF spraying painting robots which is easy to operation, and has high efficiency and stable performance. With Googol controller platform, this paper develops programs based on Windows CE embedded systems to control the robot to finish the painting work. Software development is the core of the robot control system, including the direct teaching module, playback module, motion control module, setting module, man-machine interface, alarm module, log module, etc. All the development work of the entire software system has been completed, and it has been verified that the entire software works steady and efficient.

Step 1: Human System Integration (HSI) FY05 Pilot-Technology Interface Requirements for Command, Control, and Communications (C3)

Science.gov (United States)

2005-01-01

The document provides the Human System Integration(HSI) high-level functional C3 HSI requirements for the interface to the pilot. Description includes (1) the information required by the pilot to have knowledge C3 system status, and (2) the control capability needed by the pilot to obtain C3 information. Fundamentally, these requirements provide the candidate C3 technology concepts with the necessary human-related elements to make them compatible with human capabilities and limitations. The results of the analysis describe how C3 operations and functions should interface with the pilot to provide the necessary C3 functionality to the UA-pilot system. Requirements and guidelines for C3 are partitioned into three categories: (1) Pilot-Air Traffic Control (ATC) Voice Communications (2) Pilot-ATC Data Communications, and (3) command and control of the unmanned aircraft (UA). Each requirement is stated and is supported with a rationale and associated reference(s).

Reviewing the impact of advanced control room technology

International Nuclear Information System (INIS)

Wilhelmsen, C.A.; Gertman, D.I.; Ostrom, L.T.; Nelson, W.R.; Galyean, W.J.; Byers, J.C.

1992-01-01

Progress to date on assessing the nature of the expected changes in human performance and risk associated with the introduction of digital control, instrumentation, and display systems is presented. Expected changes include the shift toward more supervisory tasks, development of intervention strategies, and reallocation of function between human and machine. Results are reported in terms of the scope of new technology, human performance issues, and crews experience with digital control systems in a variety of industries petrochemical and aerospace. Plans to conduct a limited Probabilistic Risk Assessment/Human Reliability Assessment (PRA/HRA) comparison between a conventional NUREG-1150 series plant and that same plant retrofit with distributed control and advanced instrumentation and display are also presented. Changes needed to supplement existing HRA modeling methods and quantification techniques are discussed

Integration of analog and digital instrumentation and control systems in hybrid control rooms

International Nuclear Information System (INIS)

2010-01-01

he IAEA's activities in the area of nuclear power plant operating performance and life cycle management are aimed at increasing Member State capabilities in utilizing good engineering and management practices as developed and transferred by the IAEA. In particular, the IAEA supports the improvement of nuclear power plant performance, plant life management, training, power uprating, operational license renewal, and the modernization of instrumentation and control (I and C) systems of plants. The issue of the integration of analog and digital I and C systems in hybrid control rooms was suggested by the IAEA Technical Working Group on Nuclear Power Plant Control and Instrumentation (TWG-NPPCI) at its meetings in 2003 and 2005. The subject was then approved by the IAEA and included in its work programmes for 2006-2009. The purpose of this report is to help nuclear utilities in planning control room and other human system interface (HSI) changes, making appropriate use of modern technologies. These technologies would aid in managing ageing and obsolescence, and facilitate improvements in plant performance and safety. This report covers a broad spectrum of potential changes to the control room ranging from the replacement of a few obsolete components with newer digital devices to a fully computerized control room. New digital technologies offer significant opportunities to improve access to and presentation of information to the user, e.g. operators, maintenance staff and management. However, this technology should be used prudently. In some cases, modernization is undertaken to resolve ageing and obsolescence or to meet regulatory requirements for license renewal. The integration of new technologies during main control room (MCR) modernizations should be performed cautiously and all affected aspects of plant maintenance, and operation should be carefully considered, paying particular attention to the human factors elements of these aspects. This report describes a

A Plan for Revolutionary Change in Gas Turbine Engine Control System Architecture

Science.gov (United States)

Culley, Dennis E.

2011-01-01

The implementation of Distributed Engine Control technology on the gas turbine engine has been a vexing challenge for the controls community. A successful implementation requires the resolution of multiple technical issues in areas such as network communications, power distribution, and system integration, but especially in the area of high temperature electronics. Impeding the achievement has been the lack of a clearly articulated message about the importance of the distributed control technology to future turbine engine system goals and objectives. To resolve these issues and bring the technology to fruition has, and will continue to require, a broad coalition of resources from government, industry, and academia. This presentation will describe the broad challenges facing the next generation of advanced control systems and the plan which is being put into action to successfully implement the technology on the next generation of gas turbine engine systems.

Fundamentals of automotive and engine technology standard drives, hybrid drives, brakes, safety systems

CERN Document Server

2014-01-01

Hybrid drives and the operation of hybrid vehicles are characteristic of contemporary automotive technology. Together with the electronic driver assistant systems, hybrid technology is of the greatest importance and both cannot be ignored by today’s car drivers. This technical reference book provides the reader with a firsthand comprehensive description of significant components of automotive technology. All texts are complemented by numerous detailed illustrations. Contents History of the automobile.- History of the Diesel engine.- Areas of use for Diesel engines.- Basic principles of the Diesel engine.- Basic principles of Diesel fuel-injection.- Basic principles of the gasoline engine.- Inductive ignition system.- Transmissions for motor vehicles.- Motor vehicle safety.- Basic principles of vehicle dynamics.- Car braking systems.- Vehicle electrical systems.- Overview of electrical and electronic systems in the vehicle.- Control of gasoline engines.- Control of Diesel engines.- Lighting technology.- Elec...

The status of the LAMPF control system upgrade

International Nuclear Information System (INIS)

Carr, G.P.; Schaller, S.C.; Bjorklund, E.A.; Burns, M.J.; Harrison, J.F.; Rose, P.A.; Schultz, D.E.

1987-01-01

The upgraded Los Alamos Meson Physics Facility (LAMPF) control system is now operational. The SEL-840 computer has been removed, and all application programs are now running on VAXes. We are continuing to upgrade the control system network. We are using MicroVMS systems for distributed local control and have introduced VAXELN systems for dedicated real-time situations. Communications with both systems is based on a standardized remote procedure call interface. We have also begun to integrate the Proton Storage Ring controls with the LAMPF control system, to experiment with VAX/GPX-based workstation operator interfaces, and to investigate possible applications of artificial intelligence technology. 13 refs

Development of technology for creating intelligent control systems for power plants and propulsion systems for marine robotic systems

Science.gov (United States)

Iakovleva, E. V.; Momot, B. A.

2017-10-01

The object of this study is to develop a power plant and an electric propulsion control system for autonomous remotely controlled vessels. The tasks of the study are as follows: to assess remotely controlled vessels usage reasonability, to define the requirements for this type of vessel navigation. In addition, the paper presents the analysis of technical diagnostics systems. The developed electric propulsion control systems for vessels should provide improved reliability and efficiency of the propulsion complex to ensure the profitability of remotely controlled vessels.

Technology Roadmap Instrumentation, Control, and Human-Machine Interface to Support DOE Advanced Nuclear Energy Programs

Energy Technology Data Exchange (ETDEWEB)

Donald D Dudenhoeffer; Burce P Hallbert

2007-03-01

Instrumentation, Controls, and Human-Machine Interface (ICHMI) technologies are essential to ensuring delivery and effective operation of optimized advanced Generation IV (Gen IV) nuclear energy systems. In 1996, the Watts Bar I nuclear power plant in Tennessee was the last U.S. nuclear power plant to go on line. It was, in fact, built based on pre-1990 technology. Since this last U.S. nuclear power plant was designed, there have been major advances in the field of ICHMI systems. Computer technology employed in other industries has advanced dramatically, and computing systems are now replaced every few years as they become functionally obsolete. Functional obsolescence occurs when newer, more functional technology replaces or supersedes an existing technology, even though an existing technology may well be in working order.Although ICHMI architectures are comprised of much of the same technology, they have not been updated nearly as often in the nuclear power industry. For example, some newer Personal Digital Assistants (PDAs) or handheld computers may, in fact, have more functionality than the 1996 computer control system at the Watts Bar I plant. This illustrates the need to transition and upgrade current nuclear power plant ICHMI technologies.

NPL superconducting Linac control system

International Nuclear Information System (INIS)

Swanson, H.E.; Howe, M.A.; Jackson, L.W.; LaCroix, J.M.; Readdy, H.P.; Storm, D.W.; Van Houten, L.P.

1985-01-01

The control system for the NPL Linac is based on a Microvax II host computer connected in a star network with 9 satellite computers. These satellites use single board varsions of DEC's PDP 11 processor. The operator's console uses high performance graphics and touch screen technology to display the current linac status and as the means for interactively controlling the operation of the accelerator

Structural Control Systems Implemented in Civil Engineering

Directory of Open Access Journals (Sweden)

Cristian Pastia

2005-01-01

Full Text Available Over the past three decades, a great interest has been generated by the use of protection systems to mitigate the effects of dynamic environmental hazards on civil engineering structures, such as earthquakes and strong wind. These control systems develop controllable forces to add or dissipate energy in a structure, or both, due to specific devices integrated with sensors, controllers and real – time process to operate. The paper includes the advantages of these technologies consisting of the following sections: 1 represents an introduction, 2 deals with passive control system, 3 regards some control techniques, 4 concerns hybrid control techniques, 5 contains semi – active control techniques, and 6 is dedicated to general conclusions.

The Surveillance Society: Information Technology and Bureaucratic Social Control.

Science.gov (United States)

Gandy, Oscar H., Jr.

1989-01-01

Describes how communications and information technologies are being used to increase the reach and influence of bureaucratic surveillance, creating an increasing inequality between those who provide and those who gather personal information. Argues that the current legal system is hopelessly inadequate to the challenge of controlling the…

Training Center for Industrial Control Systems

Directory of Open Access Journals (Sweden)

V. D. Yezhov

2013-01-01

Full Text Available We consider the application of embedded microcontrollers and industrial controllers with built-in operating systems.With the development of embedded operating systems and technology of open standard IEC 61131-3 product developer can write their own program management and support staff – to modernize management program.

Environmental control and life support system requirements and technology needs for advanced manned space missions

Science.gov (United States)

Powell, Ferolyn T.; Sedej, Melaine; Lin, Chin

1987-01-01

NASA has completed an environmental control and life support system (ECLSS) technology R&D plan for advanced missions which gave attention to the drivers (crew size, mission duration, etc.) of a range of manned missions under consideration. Key planning guidelines encompassed a time horizon greater than 50 years, funding resource requirements, an evolutionary approach to goal definition, and the funding of more than one approach to satisfy a given perceived requirement. Attention was given to the ECLSS requirements of transportation and service vehicles, platforms, bases and settlements, ECLSS functions and average load requirements, unique drivers for various missions, and potentially exploitable commonalities among vehicles and habitats.

Development of Adaptive Acoustic Impedance Control Technologies of Acoustic Duct Liner

Directory of Open Access Journals (Sweden)

Hiroshi Kobayashi

2011-01-01

Full Text Available This paper describes the development of adaptive acoustic impedance control (AAC technologies to achieve a larger fan noise reduction, by adaptively adjusting reactance and resistance of the acoustic liner impedance. For the actual proof of the AAC technology III performance, the advanced fan noise absorption control duct liner II was made on trial basis, with the simple control system and the plain device. And, then, the duct liner II was examined for the AAC technology I, II, and III models, using the high speed fan test facility. The test results made clear that the duct liner II of the AAC technology III model could achieve the fan noise reduction higher than O.A. SPL 10 dB (A at the maximum fan speed 6000 rpm, containing the reduction of fundamental BPF tone of 18 dB and 2nd BPF tone of 10 dB in response to the fan peed change from 3000 to 6000 rpm.

Bridging the gap: adapting advanced display technologies for use in hybrid control rooms

International Nuclear Information System (INIS)

Jokstad, Håkon; Boring, Ronald

2015-01-01

The Institute for Energy Technology (IFE), runs the OECD Halden Reactor Project (HRP), featuring a state-of-the-art research simulator facility in Halden, Norway, called HAMMLAB. HAMMLAB serves two main purposes: the study of human behaviour in interaction with complex process systems; and the development, test and evaluation of prototype control centres and their individual systems. By studying operator performance in HAMMLAB and integrating the knowledge gained into new designs, the HRP contributes to improving operational safety, reliability, efficiency and productivity. The U.S. Department of Energy's (DOE) Light Water Reactor Sustainability (LWRS) Program has contracted IFE to assist DOE national laboratory staff at Idaho National Laboratory (INL) in adapting HAMMLAB design concepts for the purpose of control room modernization at nuclear power plants in the U.S. In support of this effort, the DOE has built a simulator research facility at INL called the Human Systems Simulation Laboratory (HSSL). The HSSL is centered on control room modernization, in which industry provided plant instrumentation and controls are modified for upgrade opportunities. The HSSL houses the LWRS simulator, which is a reconfigurable full-scale and full-scope control room simulator. Consisting of 45 large touchscreens on 15 panels, the LWRS simulator is currently using this glass top technology to digitally represent and replicate the functionality of the analog I&C systems in existing control rooms. The LWRS simulator is reconfigurable in that different plant training simulator models obtained from the utilities can be run on the panels, and the panels can be physically moved and arranged to mimic the layout of those control rooms. The glass top technology and reconfigurability capabilities allow the LWRS simulator to be the research platform that is necessary to design, prototype, and validate human-system interface (HSI) technologies that can replace existing analog I&C. IFE

Bridging the gap: adapting advanced display technologies for use in hybrid control rooms

Energy Technology Data Exchange (ETDEWEB)

Jokstad, Håkon [Inst. for Energy Technology, Halden (Norway); Boring, Ronald [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-02-01

The Institute for Energy Technology (IFE), runs the OECD Halden Reactor Project (HRP), featuring a state-of-the-art research simulator facility in Halden, Norway, called HAMMLAB. HAMMLAB serves two main purposes: the study of human behaviour in interaction with complex process systems; and the development, test and evaluation of prototype control centres and their individual systems. By studying operator performance in HAMMLAB and integrating the knowledge gained into new designs, the HRP contributes to improving operational safety, reliability, efficiency and productivity. The U.S. Department of Energy’s (DOE) Light Water Reactor Sustainability (LWRS) Program has contracted IFE to assist DOE national laboratory staff at Idaho National Laboratory (INL) in adapting HAMMLAB design concepts for the purpose of control room modernization at nuclear power plants in the U.S. In support of this effort, the DOE has built a simulator research facility at INL called the Human Systems Simulation Laboratory (HSSL). The HSSL is centered on control room modernization, in which industry provided plant instrumentation and controls are modified for upgrade opportunities. The HSSL houses the LWRS simulator, which is a reconfigurable full-scale and full-scope control room simulator. Consisting of 45 large touchscreens on 15 panels, the LWRS simulator is currently using this glass top technology to digitally represent and replicate the functionality of the analog I&C systems in existing control rooms. The LWRS simulator is reconfigurable in that different plant training simulator models obtained from the utilities can be run on the panels, and the panels can be physically moved and arranged to mimic the layout of those control rooms. The glass top technology and reconfigurability capabilities allow the LWRS simulator to be the research platform that is necessary to design, prototype, and validate human-system interface (HSI) technologies that can replace existing analog I&C. IFE has

Power system small signal stability analysis and control

CERN Document Server

Mondal, Debasish; Sengupta, Aparajita

2014-01-01

Power System Small Signal Stability Analysis and Control presents a detailed analysis of the problem of severe outages due to the sustained growth of small signal oscillations in modern interconnected power systems. The ever-expanding nature of power systems and the rapid upgrade to smart grid technologies call for the implementation of robust and optimal controls. Power systems that are forced to operate close to their stability limit have resulted in the use of control devices by utility companies to improve the performance of the transmission system against commonly occurring power system

Cross-Layer Adaptive Feedback Scheduling of Wireless Control Systems

Science.gov (United States)

Xia, Feng; Ma, Longhua; Peng, Chen; Sun, Youxian; Dong, Jinxiang

2008-01-01

There is a trend towards using wireless technologies in networked control systems. However, the adverse properties of the radio channels make it difficult to design and implement control systems in wireless environments. To attack the uncertainty in available communication resources in wireless control systems closed over WLAN, a cross-layer adaptive feedback scheduling (CLAFS) scheme is developed, which takes advantage of the co-design of control and wireless communications. By exploiting cross-layer design, CLAFS adjusts the sampling periods of control systems at the application layer based on information about deadline miss ratio and transmission rate from the physical layer. Within the framework of feedback scheduling, the control performance is maximized through controlling the deadline miss ratio. Key design parameters of the feedback scheduler are adapted to dynamic changes in the channel condition. An event-driven invocation mechanism for the feedback scheduler is also developed. Simulation results show that the proposed approach is efficient in dealing with channel capacity variations and noise interference, thus providing an enabling technology for control over WLAN. PMID:27879934

Cross-Layer Adaptive Feedback Scheduling of Wireless Control Systems

Directory of Open Access Journals (Sweden)

Jinxiang Dong

2008-07-01

Full Text Available There is a trend towards using wireless technologies in networked control systems. However, the adverse properties of the radio channels make it difficult to design and implement control systems in wireless environments. To attack the uncertainty in available communication resources in wireless control systems closed over WLAN, a cross-layer adaptive feedback scheduling (CLAFS scheme is developed, which takes advantage of the co-design of control and wireless communications. By exploiting crosslayer design, CLAFS adjusts the sampling periods of control systems at the application layer based on information about deadline miss ratio and transmission rate from the physical layer. Within the framework of feedback scheduling, the control performance is maximized through controlling the deadline miss ratio. Key design parameters of the feedback scheduler are adapted to dynamic changes in the channel condition. An eventdriven invocation mechanism for the feedback scheduler is also developed. Simulation results show that the proposed approach is efficient in dealing with channel capacity variations and noise interference, thus providing an enabling technology for control over WLAN.

Exploring a new paradigm for accelerators and large experimental apparatus control systems

International Nuclear Information System (INIS)

Catani, L.; Ammendola, R.; Zani, F.; Bisegni, C.; Ciuffetti, P.; Di Pirro, G.; Mazzitelli, G.; Stecchi, A.; Calabro, S.; Foggetta, L.

2012-01-01

The integration of web technologies and web services has been, in the recent years, one of the major trends in upgrading and developing control systems for accelerators and large experimental apparatuses. Usually, web technologies have been introduced to complement the control systems with smart add-on and user friendly services or, for instance, to safely allow access to the control system to users from remote sites. Despite this still narrow spectrum of employment, some software technologies developed for high performance web services, although originally intended and optimized for these particular applications, deserve some features that would allow their deeper integration in a control system and, eventually, using them to develop some of the control system's core components. In this paper we present the conclusion of the preliminary investigations of a new design for an accelerator control system and associated machine data acquisition system (DAQ), based on a synergic combination of network distributed object caching (DOC) and a non-relational key/value database (KVDB). We investigated these technologies with particular interest on performances, namely speed of data storage and retrieve for the distributed caching, data throughput and queries execution time for the database and, especially, how much this performances can benefit from their inherent adaptability. (authors)

Power system stabilizers based on modern control techniques

Energy Technology Data Exchange (ETDEWEB)

Malik, O P; Chen, G P; Zhang, Y; El-Metwally, K [Calgary Univ., AB (Canada). Dept. of Electrical and Computer Engineering

1994-12-31

Developments in digital technology have made it feasible to develop and implement improved controllers based on sophisticated control techniques. Power system stabilizers based on adaptive control, fuzzy logic and artificial networks are being developed. Each of these control techniques possesses unique features and strengths. In this paper, the relative performance of power systems stabilizers based on adaptive control, fuzzy logic and neural network, both in simulation studies and real time tests on a physical model of a power system, is presented and compared to that of a fixed parameter conventional power system stabilizer. (author) 16 refs., 45 figs., 3 tabs.

RFID-Based Monitoring And Access Control System For Parliamentary Campus

Directory of Open Access Journals (Sweden)

Sai Thu Rein Htun

2015-08-01

Full Text Available This paper is to implement monitoring and access control system based on RFID and Zigbee technology which can be used at Parliamentary Campus. Nowadays RFID technology is widely used for access control system because it is cheap waterproof and easy to use as well as it contains unique EPC electronic protect code .In addition Zigbee wireless module is cost-effective and can be reliable for security. Sothis system consists of RFID tag RFID reader Arduino Uno and Zigbee. This system can also be used for industrial amp commercial and security HVAC closures. This paper describes the results of point-to-point connection and point-to-multipoint connection using Zigbee and RFID technology.

Distributed computer control systems in future nuclear power plants

International Nuclear Information System (INIS)

Yan, G.; L'Archeveque, J.V.R.; Watkins, L.M.

1978-09-01

Good operating experience with computer control in CANDU reactors over the last decade justifies a broadening of the role of digital electronic and computer related technologies in future plants. Functions of electronic systems in the total plant context are reappraised to help evolve an appropriate match between technology and future applications. The systems research, development and demonstration program at CRNL is described, focusing on the projects pertinent to the real-time data acquisition and process control requirements. (author)

NPP Temelin instrumentation and control system upgrade and verification

International Nuclear Information System (INIS)

Ubra, O.; Petrlik, J.

1998-01-01

Two units of Ver 1000 type of the Czech nuclear power plant Temelin, which are under construction are being upgraded with the latest instrumentation and control system delivered by WEC. To confirm that the functional design of the new Reactor Control and Limitation System, Turbine Control System and Plant Control System are in compliance with the Czech customer requirements and that these requirements are compatible with NPP Temelin upgraded technology, the verification of the control systems has been performed. The method of transient analysis has been applied. Some details of the NPP Temelin Reactor Control and Limitation System verification are presented.(author)

FPGA - Based Technology and Systems for I and C of Existing and Advanced Reactors

International Nuclear Information System (INIS)

Bachmach, E.; Siora, O.; Tokarev, V.; Reshetytsky, S.; Kharchenko, V.; Bezsalyi, V.

2011-01-01

Control systems of modern nuclear installations (including water-cooled, WCR) are based on programmable technologies. Most of control systems modernizations which are implemented at operating nuclear installations are also based on application of programmable technologies. Besides, a range of features and properties is defied for programmable technologies. These features and properties make licensing process more complicated, facilitate appearance of common cause failures, make safety evaluation procedures more complicated, etc. Also it is known that programmable technologies significantly extend the time periods for project realization of new power units construction and modernization of the existing power units, and also it involves rise of its value. Company RADIY has developed the Platform of digital equipment RADIY on FPGA-based technology. In the article there is a description of the features of FPGA-technology developed and applied by Company RADIY, features of the Platform RADIY and systems realized on its base, which allow to minimize significantly above-mentioned negative features and properties of programmable technologies. Technology which realized in Platform RADIY allows to solve the whole set of tasks of control (including regulation) and protection of nuclear installations. Platform RADIY is a combination of the best features of traditional programmable technologies and FPGA-technology. According to the opinion of the authors of this article the technology which is realized in Platform RADIY is the key factor for solving of control and protection tasks of nuclear installations in the nearest future. (author)

Non-invasive brain-computer interface system: towards its application as assistive technology.

Science.gov (United States)

Cincotti, Febo; Mattia, Donatella; Aloise, Fabio; Bufalari, Simona; Schalk, Gerwin; Oriolo, Giuseppe; Cherubini, Andrea; Marciani, Maria Grazia; Babiloni, Fabio

2008-04-15

The quality of life of people suffering from severe motor disabilities can benefit from the use of current assistive technology capable of ameliorating communication, house-environment management and mobility, according to the user's residual motor abilities. Brain-computer interfaces (BCIs) are systems that can translate brain activity into signals that control external devices. Thus they can represent the only technology for severely paralyzed patients to increase or maintain their communication and control options. Here we report on a pilot study in which a system was implemented and validated to allow disabled persons to improve or recover their mobility (directly or by emulation) and communication within the surrounding environment. The system is based on a software controller that offers to the user a communication interface that is matched with the individual's residual motor abilities. Patients (n=14) with severe motor disabilities due to progressive neurodegenerative disorders were trained to use the system prototype under a rehabilitation program carried out in a house-like furnished space. All users utilized regular assistive control options (e.g., microswitches or head trackers). In addition, four subjects learned to operate the system by means of a non-invasive EEG-based BCI. This system was controlled by the subjects' voluntary modulations of EEG sensorimotor rhythms recorded on the scalp; this skill was learnt even though the subjects have not had control over their limbs for a long time. We conclude that such a prototype system, which integrates several different assistive technologies including a BCI system, can potentially facilitate the translation from pre-clinical demonstrations to a clinical useful BCI.

2nd International Conference on Intelligent Technologies and Engineering Systems

CERN Document Server

Chen, Cheng-Yi; Yang, Cheng-Fu

2014-01-01

This book includes the original, peer reviewed research papers from the 2nd International Conference on Intelligent Technologies and Engineering Systems (ICITES2013), which took place on December 12-14, 2013 at Cheng Shiu University in Kaohsiung, Taiwan. Topics covered include: laser technology, wireless and mobile networking, lean and agile manufacturing, speech processing, microwave dielectrics, intelligent circuits and systems, 3D graphics, communications, and structure dynamics and control.

Physics and chemistry of plasma pollution control technology

International Nuclear Information System (INIS)

Chang, J S

2008-01-01

Gaseous pollution control technologies for acid gases (NO x , SO x , etc), volatile organic compounds, greenhouse gases, ozone layer depleting substances, etc have been commercialized based on catalysis, incineration and adsorption methods. However, non-thermal plasma techniques based on electron beams and corona discharges are becoming significant due to advantages such as lower costs, higher removal efficiency and smaller space volume. In order to commercialize this new technology, the pollution gas removal rate, energy efficiency of removal, pressure drop of reactors and useable by-product production rates must be improved and identification of major fundamental processes and optimizations of reactor and power supply for an integrated system must be investigated. In this work, the chemistry and physics of plasma pollution control are discussed and the limitation of this type of plasma is outlined based on the plasma parameters.

Control of the technological processes at ''Azovstal'' plant using radioisotope devices

Energy Technology Data Exchange (ETDEWEB)

Nosochenko, O V; Overchenko, Z V; Karpov, O I; Deryabina, G N

1980-05-01

Considered is the state of radioisotope control of the technological process at 'Azovstal' plant which has permitted to increase the quality of metal and of metal production. With the help of radioisotope densimeter PR-1024 carried out is the control of the density of the lime solution used for hearth spraying at pig iron casting. A system of automatic correction of skip coke supply according to indications of moisture gauges ''Neutron 3-1'' is implemented at blast furnaces. A radioisotope thickness gauge of hot rolling is positioned on the section of finishing stand of thick-sheet plant, its operation is based on the ..gamma.. radiation weakening in dependence on sheet thickness. The introduction of thickness gauges in the automatized system of rolling control is planned. A radioisotope device ''Paza 2'' for measuring of continuous ingot skin thickness is tested successively at the plant. Gamma-relay devices are used to control the level of loose materials in bunkers. Noted is the prospects of using radioisotopic means of control and automatization of technological processes in ferrous matallurgy.

Bridge between control science and technology. Volume 5 Manufacturing man-machine systems, computers, components, traffic control, space applications

Energy Technology Data Exchange (ETDEWEB)

Rembold, U; Kempf, K G; Towill, D R; Johannsen, G; Paul, M

1985-01-01

Among the topics discussed are: robotics; CAD/CAM applications; and man-machine systems. Consideration is also given to: tools and software for system design and integration; communication systems for real-time computer control; fail-safe design of real-time computer systems; and microcomputer-based control systems. Additional topics discussed include: programmable and intelligent components and instruments in automatic control; transportation systems; and space applications of automatic control systems.

Design concept of Hydro cascade control system

International Nuclear Information System (INIS)

Fustik, Vangel; Kiteva, Nevenka

2006-01-01

In this paper a design concept of the comple hydro cascade scheme is presented with the design parameters of the main technical features. The cascade control system architecture is designed considering up-to-date communication and information technology. The control algorithm is based on Pond Level Control and Economic Load Allocation concepts.

Portal monitoring technology control process

International Nuclear Information System (INIS)

York, R.L.

1998-01-01

Portal monitors are an important part of the material protection, control, and accounting (MPC and A) programs in Russia and the US. Although portal monitors are only a part of an integrated MPC and A system, they are an effective means of controlling the unauthorized movement of special nuclear material (SNM). Russian technical experts have gained experience in the use of SNM portal monitors from US experts ad this has allowed them to use the monitors more effectively. Several Russian institutes and companies are designing and manufacturing SNM portal monitors in Russia. Interactions between Russian and US experts have resulted in improvements to the instruments. SNM portal monitor technology has been effectively transferred from the US to Russia and should be a permanent part of the Russian MPC and A Program. Progress in the implementation of the monitors and improvements to how they are used are discussed

Distributed automatic control of technological processes in conditions of weightlessness

Science.gov (United States)

Kukhtenko, A. I.; Merkulov, V. I.; Samoylenko, Y. I.; Ladikov-Royev, Y. P.

1986-01-01

Some problems associated with the automatic control of liquid metal and plasma systems under conditions of weightlessness are examined, with particular reference to the problem of stability of liquid equilibrium configurations. The theoretical fundamentals of automatic control of processes in electrically conducting continuous media are outlined, and means of using electromagnetic fields for simulating technological processes in a space environment are discussed.

Printing technologies in fabrication of drug delivery systems.

Science.gov (United States)

Kolakovic, Ruzica; Viitala, Tapani; Ihalainen, Petri; Genina, Natalja; Peltonen, Jouko; Sandler, Niklas

2013-12-01

There has been increased activity in the field recently regarding the development and research on various printing techniques in fabrication of dosage forms and drug delivery systems. These technologies may offer benefits and flexibility in manufacturing, potentially paving the way for personalized dosing and tailor-made dosage forms. In this review, the most recent observations and advancements in fabrication of drug delivery systems by utilizing printing technologies are summarized. A general overview of 2D printing techniques is presented including a review of the most recent literature where printing techniques are used in fabrication of drug delivery systems. The future perspectives and possible impacts on formulation strategies, flexible dosing and personalized medication of using printing techniques for fabrication of drug delivery systems are discussed. It is evident that there is an urgent need to meet the challenges of rapidly growing trend of personalization of medicines through development of flexible drug-manufacturing approaches. In this context, various printing technologies, such as inkjet and flexography, can play an important role. Challenges on different levels exist and include: i) technological development of printers and production lines; ii) printable formulations and carrier substrates; iii) quality control and characterization; and iv) regulatory perspectives.

On load flow control in electric power systems

Energy Technology Data Exchange (ETDEWEB)

Herbig, Arnim

2000-01-01

This dissertation deals with the control of active power flow, or load flow in electric power systems. During the last few years, interest in the possibilities to control the active power flows in transmission systems has increased significantly. There is a number of reasons for this, coming both from the application side - that is, from power system operations - and from the technological side. where advances in power electronics and related technologies have made new system components available. Load flow control is by nature a multi-input multi-output problem, since any change of load flow in one line will be complemented by changes in other lines. Strong cross-coupling between controllable components is to be expected, and the possibility of adverse interactions between these components cannot be rejected straightaway. Interactions with dynamic phenomena in the power system are also a source of concern. Three controllable components are investigated in this thesis, namely the controlled series capacitor (CSC), the phase angle regulator (PAR), and the unified power flow controller (UPFC). Properties and characteristics of these devices axe investigated and discussed. A simple control strategy is proposed. This strategy is then analyzed extensively. Mathematical methods and physical knowledge about the pertinent phenomena are combined, and it is shown that this control strategy can be used for a fairly general class of devices. Computer simulations of the controlled system provide insight into the system behavior in a system of reasonable size. The robustness and stability of the control system are discussed as are its limits. Further, the behavior of the control strategy in a system where the modeling allows for dynamic phenomena are investigated with computer simulations. It is discussed under which circumstances the control action has beneficial or detrimental effect on the system dynamics. Finally, a graphical approach for analyzing the effect of controllers

The strategy for intelligent integrated instrumentation and control system development

International Nuclear Information System (INIS)

Kwon, Kee Choon; Ham, Chang Shik

1995-01-01

All of the nuclear power plants in Korea are operating with analog instrumentation and control ( I and C) equipment which are increasingly faced with frequent troubles, obsolescence and high maintenance expenses. Electrical and computer technology has improved rapidly in recent years and has been applied to other industries. So it is strongly recommended we adopt modern digital and computer technology to improve plant safety and availability. The advanced I and C system, namely, Integrated Intelligent Instrumentation and Control System (I 3 Cs) will be developed for beyond the next generation nuclear power plant. I 3 CS consists of three major parts, the advanced compact workstation, distributed digital control and protection system including Automatic Start-up/Shutdown Intelligent Control System (ASICS) and the computer-based alarm processing and operator support system, namely, Diagnosis, Response, and operator Aid Management System (DREAMS)

Technological measures for controlling the use of copyrighted works of authorship in the information society

Directory of Open Access Journals (Sweden)

Spasić Vidoje

2016-01-01

Full Text Available Information technology has given rise to the problem of controlling the use of copyrighted works of authorship from their unauthorized use. In this context, one of the effective solutions is the application of technological protection measures, which are aimed at a more efficient application of the protection measures prescribed by the law. Technological protection measures imply the use of any technology, device or component which may be aimed at preventing or restricting an unauthorized use of a protected work of authorship, which has not been approved by the author or holder of some related right. Generally, all these measures may be classified into three basic groups: technological measures aimed at controlling access, technological measured aimed at controlling exploitation, and technological measures aimed at protecting the integrity of the work of authorship. Considering their technical characteristics and mode of application, they may be hardware-based measures, software-based measures, or a combination thereof. Modern technology has enabled the development of digital systems which entail a controlled use of copyrighted works and facilitate obtaining licences for their exploitation. They are commonly known as digital rights management (DRM. The DRM system should provide for a compromise between safeguarding the intellectual property rights of the copyright holder, the end user privacy, and system costs. The envisaged goals are achieved by employing various cryptographic measures. The process of developing technological protection measures is accompanied by concurrent attempts to circumvent the application of these measures. Thus, the effectiveness of these measures primarily depends on their legal protection, which has been recognized by a vast majority of legal systems, we now know the most modern legal system. However, the normative solutions are not uniform. The observed differences actually reflect problems in finding adequate forms

Implementation of digital control and protection systems of China advanced research reactor

International Nuclear Information System (INIS)

Zeng Hai; Jin Huajin; Xu Qiguo; Zhang Mingkui

2005-01-01

China Advanced Research Reactor (CARR), a reactor of the 21st century with high performance is being constructed in China. The requirements of reliability and stability on the control and protection (c and p) system are the main points raised. Especially, with the development of digital technology, the c and p system of CARR is demanded to match the trend of digitization in the field of reactor control. The c and p system, including reactor protection system, reactor monitoring and control system, reactor power regulating system, and the mitigation system for ATWS (Anticipate Transient Without Scram), adopts digital technology, and the digital display screen will replace the analog panels in the main control room. The c and p system of CARR adopts redundant technology with 2 or 3 redundant channels to improve the system reliability. The 10/100 Mbps self-adaptive redundant optic fiber industry Ethernet ring network is used to interlink operator workstations, supervisor workstation, and I/O control stations. Commercial grade equipment with mature experience in industrial application are applied to the c and p system of CARR, which have high reliability, good interchangeability, and is easily purchased, the software-developing tools fully match the international industry standards. The realization of digital c and p system of CARR will promote the progress of digital control technology for reactors in China, and certainly become a technical basic platform for developing informational and intelligent reactors in China. (authors)

Best available technology equivalent controls for B Plant Process Condensate: Tank farm process technology section

International Nuclear Information System (INIS)

1988-11-01

This report evaluates whether proposed controls for the B Plant Process Condensate effluent stream are equivalent to Best Available Technology (BAT) economically achievable. Methods to determine whether the proposed controls for the BCP were equivalent to BAT originated from the Guidance Document for the Hanford Site. The BAT performance standards, which originate from the Clean Water Act, are to be applied to all contaminated liquid effluent discharges currently going to the soil column at the Hanford Site. The B Plant BAT evaluation addressed pollutants that had not been regulated traditionally under Federal or State water-pollution control programs. As a result, only comparisons could be made to existing radiation and water quality standards, and a BAT determination based on the effluent guidelines method (as outlined in the BAT Guidance Document) was not possible. Due to the variability and inconsistency of factors with comparable streams, such as the effluent stream at the Savannah River Plant, a BAT determination by the technology transfer method and treatability studies method was not possible. By using the generic treatment systems method, a one-or two-stage treatment system for dissolved solids removal was concluded to be equivalent to BAT. By performing two economic achievability tests, a one-stage treatment system consisting of mixed bed ion exchange columns was considered to be cost effective and equivalent to BAT. 13 refs., 4 figs., 5 tabs

Evolution of the Argonne Tandem Linear Accelerator System (ATLAS) control system

International Nuclear Information System (INIS)

Power, M.; Munson, F.

2012-01-01

Given that the Argonne Tandem Linear Accelerator System (ATLAS) recently celebrated its 25. anniversary, this paper will explore the past, present, and future of the ATLAS Control System, and how it has evolved along with the accelerator and control system technology. ATLAS as we know it today, originated with a Tandem Van de Graff in the sixties. With the addition of the Booster section in the late seventies, came the first computerized control. ATLAS itself was placed into service on June 25, 1985, and was the world's first superconducting linear accelerator for ions. Since its dedication as a National User Facility, more than a thousand experiments by more than 2,000 users worldwide, have taken advantage of the unique capabilities it provides. Today, ATLAS continues to be a user facility for physicists who study the particles that form the heart of atoms. Its most recent addition, CARIBU (Californium Rare Isotope Breeder Upgrade), creates special beams that feed into ATLAS. ATLAS is similar to a living organism, changing and responding to new technological challenges and research needs. As it continues to evolve, so does the control system: from the original days using a DEC PDP-11/34 computer and two CAMAC crates, to a DEC Alpha computer running Vsystem software and more than twenty CAMAC crates, to distributed computers and VME systems. Future upgrades are also in the planning stages that will continue to evolve the control system. (authors)

Renewable energy technology for off-grid power generation solar hybrid system

International Nuclear Information System (INIS)

Mohd Azhar Abd Rahman

2006-01-01

Off-grid power generation is meant to supply remote or rural area, where grid connection is almost impossible in terms of cost and geography, such as island, aborigine's villages, and areas where nature preservation is concern. Harnessing an abundance renewable energy sources using versatile hybrid power systems can offer the best, least-cost alternative solution for extending modern energy services to remote and isolated communities. The conventional method for off-grid power generation is using diesel generator with a renewable energy (RE) technology utilizing solar photovoltaic, wind, biomass, biogas and/or mini/micro hydro. A hybrid technology is a combination of multiple source of energy; such as RE and diesel generator and may also include energy storage such as battery. In our design, the concept of solar hybrid system is a combination of solar with diesel genset and battery as an energy storage. The main objective of the system are to reduce the cost of operation and maintenance, cost of logistic and carbon dioxide (CO 2 ) emission. The operational concept of solar hybrid system is that solar will be the first choice of supplying load and excess energy produced will be stored in battery. Genset will be a secondary source of energy. The system is controlled by a microprocessor-based controlled to manage the energy supplied and load demand. The solar hybrid system consists of one or two diesel generator with electronic control system, lead-acid battery system, solar PV, inverter module and system controller with remote monitoring capability. The benefits of solar hybrid system are: Improved reliability, Improved energy services, reduced emissions and pollution, provide continuous power supply, increased operational life, reduced cost, and more efficient use of power. Currently, such system has been installed at Middle and Top Station of Langkawi Cable Car, Langkawi and Aborigines Village Kg Denai, Rompin, Pahang. The technology is considered new in Malaysia

Synthesis of pneumatic controll systems

Directory of Open Access Journals (Sweden)

D. Nowak

2011-04-01

Full Text Available Currently, the basic tool for automating the production processes are the PLCs. However, in many areas application of the pneumaticcontrol systems may be more reasonable. The main factor determining choice of the control technology are costs. In the case of pneumaticsystems, the costs shall be determined by the number of elements used. Therefore, during the design works it is important to choose anappropriate method for the pneumatic control systems synthesis. The article presents the MTS method, which may be used for a discretetechnological processes modeling and PLC programming, as well as for a pneumatic control systems designing. An important element ofthe MTS method is the network of actions, which graphically presents an algorithm of the implemented process. Based on the actionnetwork and operating machine’s functional diagram, the diagram of different states is determinated, which graphically shows changes ofthe control system’s input and output signals. Analysis of the diagram of different states, makes it easy to determine a schematic equation, which shall be the basis for the control system implementation. Advantage of the MTS method is the lack of restrictions on the number of the control system’s input and output signals. The resulting solution is characterized by a minimum number of elements needed to implement the control system.

Energy: Systems for Control, Maintenance, and Storage. A Bibliography.

Science.gov (United States)

Thomas, Gerald, Comp.; McKane, Irving, Comp.

This publication is a bibliography of available periodical literature on specific aspects of energy and today's technology. The Applied Science and Technology Indexes were searched for articles that related to these specific areas: (1) Energy control systems; (2) Maintenance of Energy Systems; and (3) Energy storage. The articles and papers…